A regression introduced in https://github.com/raspberrypi/linux/pull/3887
meant that if the newly scheduled transfer immediately returned data, and
the driver resubmitted a single URB after every transfer, then the effective
polling interval would end up being approx 1ms.
Use the larger of SCHEDULE_SLOP or the configured endpoint interval.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Adds an overlay to configure the TinyDRM driver for ST7735R
based 160x128 and 128x128 (untested) displays such as the
Adafruit 1.8" display.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
This commit updates the imx519 driver to adverise support for embedded
data streams.
The imx519 sensor subdevice overloads the media pad to differentiate
between image stream (pad 0) and embedded data stream (pad 1) when
performing the v4l2_subdev_pad_ops functions.
Signed-off-by: Lee Jackson <info@arducam.com>
Adds a driver for the 16MPix IMX519 CSI2 sensor.
Whilst the sensor supports 2 or 4 CSI2 data lanes, this driver
currently only supports 2 lanes.
The following Bayer modes are currently available:
4656x3496 10-bit @ 10fps
3840x2160 10-bit (cropped) @ 21fps
2328x1748 10-bit (binned) @ 30fps
1920x1080 10-bit (cropped/binned) @ 60fps
1280x720 10-bit (cropped/binned) @ 120fps
Signed-off-by: Lee Jackson <info@arducam.com>
The Linux support for controlling card power via regulators appears to
be contentious. I would argue that the default behaviour is contrary to
the SDHCI spec - turning off the power writes a reserved value to the
SD Bus Voltage Select field of the Power Control Register, which
seems to kill the Arasan/iProc controller - but fortunately there is a
hook in sdhci_ops to override the behaviour.
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
This reverts commit aed19399a0.
Commit 6c92ae1e45 ("mmc: sdhci: Introduce sdhci_set_power_and_bus_voltage()")
introduced a generic helper that does the same thing so use that instead in
the following commit.
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
Check for errors only if we actually tried to enable the bvb clock.
Fixes: 01a6d727b4 ("vc4/drm: hdmi: Handle case when bvb clock is null")
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
When doing an asynchronous page flip (PAGE_FLIP ioctl with the
DRM_MODE_PAGE_FLIP_ASYNC flag set), the current code waits for the
possible GPU buffer being rendered through a call to
vc4_queue_seqno_cb().
On the BCM2835-37, the GPU driver is part of the vc4 driver and that
function is defined in vc4_gem.c to wait for the buffer to be rendered,
and once it's done, call a callback.
However, on the BCM2711 used on the RaspberryPi4, the GPU driver is
separate (v3d) and that function won't do anything. This was working
because we were going into a path, due to uninitialized variables, that
was always scheduling the callback.
However, we were never actually waiting for the buffer to be rendered
which was resulting in frames being displayed out of order.
The generic API to signal those kind of completion in the kernel are the
DMA fences, and fortunately the v3d drivers supports them and signal
when its job is done. That API also provides an equivalent function that
allows to have a callback being executed when the fence is signalled as
done.
Let's change our driver a bit to rely on the previous function for the
older SoCs, and on DMA fences for the BCM2711.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The read and write functions did not use the correct pointer offset
when dealing with an odd number of bytes after a DMA transfer. Also,
only handle the remaining odd bytes if the DMA transfer completed
successfully.
Submitted-by: @madimario (GitHub)
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The driver was implementing a get_brightness function that
tried to read back the PWM setting of the display to report
as the current brightness.
The controller on the display does not support that, therefore
we end up reporting a brightness of 0, and that confuses
systemd's backlight service.
Remove the hook so that the framework returns the current
brightness automatically.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
This allows using the video-i2c camera driver with MLX90640 thermal
infrared sensors, connected to Raspberry Pi. CONFIG_VIDEO_V4L2_I2C
has to be selected to use the camera.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
The ISP can do H & V flips whilst resizing or converting
the image, so expose that via V4L2_CID_[H|V]FLIP.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Currently the code was only setting some controls from
bcm2835_codec_set_ctrls, but it's simpler to use
v4l2_ctrl_handler_setup to avoid forgetting to adding new
controls to the list.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Completions don't reference count, so setting the completion
on the first buffer returned and then not reinitialising it
means that the flush function doesn't behave as intended.
Signal the completion when the last buffer is returned.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Should we go through the timeout failure case with port_disable
not returning all buffers for whatever reason, the
buffers_with_vpu counter gets left at a non-zero value, which
will cause reference counting issues should the instance be
reused.
Reset the count when the port is enabled again, but before
any buffers have been sent to the VPU.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
When a buffer is returned on a port that is disabled, return it
to the videobuf2 QUEUED state instead of DONE which returns it
to the client.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The firmware defaults to not stopping video decode if only the
pixel aspect ratio or colourspace change. V4L2 requires us
to stop decoding on any change, therefore tell the firmware
of the desire for this alternate behaviour.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
When a format changed event occurs, the spec says that it
triggers an implicit drain, and that needs to be signalled
via -EPIPE.
For BCM2835, the format changed event happens at the point
the format change occurs, so no further buffers exist from
before the resolution changed point. We therefore signal the
last buffer immediately.
We don't have a V4L2 available to us at this point, so set
the videobuf2 queue last_buffer_dequeued flag directly.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The list of includes was slightly over generic, and wasn't
in alphabetical order. Clean it up.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
With video decode we now enable both input and output ports on
the component. This means that buffers will get passed to the VPU
earlier than desired if they are queued befoer STREAMON.
Check that the queue is streaming before sending buffers to the VPU.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The V4L2 stateful video decoder API requires that you can STREAMON
on only the OUTPUT queue, feed in buffers, and wait for the
SOURCE_CHANGE event.
This requires that we enable the MMAL output port at the same time
as the input port, because the output port is the one that creates
the SOURCE_CHANGED event.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Before uniniting the decode context sync with the IRQ queues to ensure
that decode no longer has any buffers in use. This fixes a problem that
manifested as ffmpeg leaking CMA buffers when it did a stream off on
OUTPUT before CAPTURE, though in reality it was probably much more
dangerous than that.
Signed-off-by: John Cox <jc@kynesim.co.uk>
Remove unused ctx state tracking variable and associated defines.
Their presence implies they might be used, but they aren't.
Signed-off-by: John Cox <jc@kynesim.co.uk>
With EDPWRDOWN set in idle, it must be cleared before checking for
ENERGYON going high, indicating that a link is being established.
The existing code allows 640ms for ENERGYON to go high, but on
Raspberry Pis that appears not to be enough, causing link detection
to fail.
Increase the polling timeout to 1500ms - with a polling interval of
10ms it shouldn't cause unnecessary delays.
See: https://github.com/raspberrypi/linux/issues/4393
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
V4L2 spec says that G/S/TRY_FMT IOCTLs should never return errors for
anything other than wrong buffer types. Improve the capture format
function such that this is so and unsupported values get converted
to supported ones properly.
Signed-off-by: John Cox <jc@kynesim.co.uk>
A failure of some CPU cores to come online has been traced to the
failure of a stm instruction while the cache is disabled. The symptom
is that the saved values read back as zeroes, a catastrophic error since
one of the values is a return address.
This patch forces a readback and retry until the correct value is
returned,
Notes:
At this stage in the boot process the core is running with its cache
disabled. Before enabling the cache its contents must be explicitly
invalidated, a process that requires quite a few registers that the
caller must preserve. Evidence suggests that something is writing a
block of zeroes over that space at a time when all other cores should
be idle, possibly some kind of write-combiner, and retrying is an
attempt to avoid the problem.
The previous attempted fix (forcing the accesses to only be 4-byte
aligned) appears to have only worked for a while and likely for less
obvious reasons such as a change in code alignment.
See: https://github.com/Hexxeh/rpi-firmware/issues/232
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
This reverts commit fe4cc0ed59.
The speculative patch that this commit reverts is proving to not be
effective any more, so revert it and try a new approach.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
As we're wanting to wrap the image_fx component for deinterlacing,
add the deinterlace algorithm values to enum mmal_parameter_imagefx
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
If the client provides a bytesperline value in try_fmt/s_fmt then
validate it and correct if necessary.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Should start_streaming fail, or buffers be queued during
stop_streaming, they should be returned to the core as QUEUED
and not (as currently) as ERROR.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The video decoder can support decoding interlaced streams, so add
the required plumbing to signal this correctly.
The encoder and ISP do NOT support interlaced data, so trying to
configure an interlaced format on those nodes will be rejected.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Adds enum mmal_interlace_type and struct
mmal_parameter_video_interlace_type to allow for querying the
interlacing mode on decoders.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
In order to effectively guarantee that a V4L2_EVENT_SOURCE_CHANGE
event occurs, adopt a default resolution of 32x32 so that it
is incredibly unlikely to be decoding a stream of that resolution
and therefore failing to note a "change" requiring the event.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The exit path of vc4_hdmi_encoder_pre_crtc_configure() is fairly hard to
maintain given its numerous error conditions.
Switch to a goto based approach to simplify it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Unlike pm_runtime_get_sync(), pm_runtime_resume_and_get() doesn't take a
reference on failure, so we don't need to call pm_runtime_put() on
failure.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Our detect function calls pm_runtime_resume_and_get() and
pm_runtime_put() to make sure the device is properly powered before
trying to access the controller.
However, it also makes sure the HSM clock is properly enabled (and
disabled), which is redundant with what runtime_pm is doing already.
Let's just remove it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The older panel-raspberrypi-touchscreen driver had issues in
that it also controlled the power for the touchscreen without
having an appropriate hook for the touchscreen driver to control
that.
Mainline has now added a Toshiba TC358762 bridge driver, and
a regulator/backlight driver for the ATTiny microcontroller on
the board. That allows clean integration with the touchscreen
driver.
Switch the overlays over to using newer drivers.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
We need independent control of the resets for the panel&bridge,
vs the touch controller.
Expose the reset lines that are on the Atmel's port C via the GPIO
API so that they can be controlled appropriately.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The Atmel was doing a load of automatic sequencing of
control lines, however it was combining the touch controller's
reset with the bridge/panel control.
Change to control the control signals directly rather than
through the automatic POWERON control.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The initial state of the Atmel is not defined, so ensure the
backlight PWM is set to 0 by default.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The driver was using the regmap lock to serialise the
individual accesses, but we really need to protect the
timings of enabling the regulators, including any communication
with the Atmel.
Use a mutex within the driver to control overall accesses to
the Atmel, instead of the regmap lock.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The Atmel is doing some things in the I2C ISR, during which
period it will not respond to further commands. This is
particularly true of the POWERON command.
Increase delays appropriately, and retry should I2C errors be
reported.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
There's no reason why 2 Raspberry Pi DSI displays can't be
attached to a Pi Compute Module, so the backlight names need to
be unique.
Use the parent dev_name. It's not as readable, but is unique.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
If no interrupt is defined then a timer and workqueue are used
to poll the controller.
On remove these were not being cleaned up correctly.
Fixes: ca61fdaba7 "Input: edt-ft5x06: Poll the device if no interrupt is
configured."
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The Raspberry Pi 7" 800x480 panel uses a Toshiba TC358762 DSI
to DPI bridge chip, so there is a requirement for the timings
to be specified for the end panel. Add such a definition.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
rpi_touchscreen_i2c_read returns any errors from i2c_transfer,
or the 8 bit received value.
Check for error values before trying to process the data as
valid.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The panel has a prepare call which is before video starts, and an
enable call which is after.
The Toshiba bridge should be configured before video, so move
the relevant power and initialisation calls to prepare.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
If a call to rpi_touchscreen_i2c_write from rpi_touchscreen_probe
fails before mipi_dsi_device_register_full is called, then
in trying to log the error message if uses ts->dsi->dev when
it is still NULL.
Use ts->i2c->dev instead, which is initialised earlier in probe.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The divider calculations tried to find the divider
just faster than the clock requested. However if
it required a divider of 7 then the for loop
aborted without handling the "error" case, and could
end up with a clock lower than requested.
Correct the loop so that we always have a clock greater
than requested.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
On Pi0-3 the driver allocates a buffer and requests a DMA channel
because the ARM can't write to DSI1's registers directly.
However unbind and the error paths in bind don't release the buffer or
the DMA channel.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The HDMI block can repeat pixels for double clocked modes,
and the firmware is now configuring the block to do this as
the PV is doing it incorrectly when at 2pixels/clock.
If the kernel doesn't reset it then we end up with strange
modes.
Reset MISC_CONTROL.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The sysfs delay_ms value is calculated live, and it is possible for
the time left to appear to be negative briefly if the timer handling
hasn't completed. Ensure the displayed value never goes below zero,
for the sake of appearances.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
A module parameter "dpc_enable" is added to allow the control of the
sensor's on-board DPC (Defective Pixel Correction) function.
This is a global setting to be configured before using the sensor;
there is no intention that this would ever be changed on-the-fly.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
drm_connector_helper_hpd_irq_event() calls
drm_kms_helper_hotplug_event() with the mode-setting lock taken while
it's supposed to be called without that lock taken.
This results in a lockdep warning, and a deadlock if we were to wake up
a TV through CEC (and possibly other cases).
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
commit 514e976744 upstream.
My local syzbot instance hit memory leak in usb_set_configuration().
The problem was in unputted usb interface. In case of errors after
usb_get_intf() the reference should be putted to correclty free memory
allocated for this interface.
Fixes: ec16dae545 ("V4L/DVB (7019): V4L: add support for Syntek DC1125 webcams")
Cc: stable@vger.kernel.org
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 15db16837a upstream.
Server responds to LOOKUP and other ops (READDIRPLUS/CREATE/MKNOD/...)
with ourarg containing nodeid and generation.
If a fuse inode is found in inode cache with the same nodeid but different
generation, the existing fuse inode should be unhashed and marked "bad" and
a new inode with the new generation should be hashed instead.
This can happen, for example, with passhrough fuse filesystem that returns
the real filesystem ino/generation on lookup and where real inode numbers
can get recycled due to real files being unlinked not via the fuse
passthrough filesystem.
With current code, this situation will not be detected and an old fuse
dentry that used to point to an older generation real inode, can be used to
access a completely new inode, which should be accessed only via the new
dentry.
Note that because the FORGET message carries the nodeid w/o generation, the
server should wait to get FORGET counts for the nlookup counts of the old
and reused inodes combined, before it can free the resources associated to
that nodeid.
Stable backport notes:
* This is not a regression. The bug has been in fuse forever, but only
a certain class of low level fuse filesystems can trigger this bug
* Because there is no way to check if this fix is applied in runtime,
libfuse test_examples.py tests this fix with hardcoded check for
kernel version >= 5.14
* After backport to stable kernel(s), the libfuse test can be updated
to also check minimal stable kernel version(s)
* Depends on "fuse: fix bad inode" which is already applied to stable
kernels v5.4.y and v5.10.y
* Required backporting helper inode_wrong_type()
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-fsdevel/CAOQ4uxi8DymG=JO_sAU+wS8akFdzh+PuXwW3Ebgahd2Nwnh7zA@mail.gmail.com/
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e3e2c4362 upstream.
inode_wrong_type(inode, mode) returns true if setting inode->i_mode
to given value would've changed the inode type. We have enough of
those checks open-coded to make a helper worthwhile.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13d9c6b998 upstream.
ASUS ROG Strix G17 has the very same PCI and codec SSID (1043:103f) as
ASUS TX300, and unfortunately, the existing quirk for TX300 is broken
on ASUS ROG. Actually the device works without the quirk, so we'll
need to clear the quirk before applying for this device.
Since ASUS ROG has a different codec (ALC294 - while TX300 has
ALC282), this patch adds a workaround for the device, just clearing
the codec->fixup_id by checking the codec vendor_id.
It's a bit ugly to add such a workaround there, but it seems to be the
simplest way.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214101
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210820143214.3654-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 222013f9ac ]
Support for cryptoloop has been officially marked broken and deprecated
in favor of dm-crypt (which supports the same broken algorithms if
needed) in Linux 2.6.4 (released in March 2004), and support for it has
been entirely removed from losetup in util-linux 2.23 (released in April
2013). Add a warning and a deprecation schedule.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20210827163250.255325-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9e6ffbc5b ]
kcalloc() is called to allocate memory for m->m_info, and if it fails,
ceph_mdsmap_destroy() behind the label out_err will be called:
ceph_mdsmap_destroy(m);
In ceph_mdsmap_destroy(), m->m_info is dereferenced through:
kfree(m->m_info[i].export_targets);
To fix this possible null-pointer dereference, check m->m_info before the
for loop to free m->m_info[i].export_targets.
[ jlayton: fix up whitespace damage
only kfree(m->m_info) if it's non-NULL ]
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Tuo Li <islituo@gmail.com>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e543468869 ]
Thanks to Kees Cook who detected the problem of memset that starting
from not the first member, but sized for the whole struct.
The better change will be to remove the redundant memset and to clear
only the msix_cnt member.
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Reported-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 85520079af ]
macb_ptp_desc will not return NULL under most circumstances with correct
Kconfig and IP design config register. But for the sake of the extreme
corner case, check for NULL when using the helper. In case of rx_tstamp,
no action is necessary except to return (similar to timestamp disabled)
and warn. In case of TX, return -EINVAL to let the skb be free. Perform
this check before marking skb in progress.
Fixes coverity warning:
(4) Event dereference:
Dereferencing a null pointer "desc_ptp"
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0cd08537d ]
For VFs we should return with an error in case we didn't get the exact
number of msix vectors as we requested.
Not doing that will lead to a crash when starting queues for this VF.
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit bae989c4bc upstream.
The ams_delta_camera_power() function is unused as reports
Clang compilation with omap1_defconfig on linux-next:
arch/arm/mach-omap1/board-ams-delta.c:462:12: warning: unused function 'ams_delta_camera_power' [-Wunused-function]
static int ams_delta_camera_power(struct device *dev, int power)
^
1 warning generated.
The soc_camera support was dropped without removing
ams_delta_camera_power() function, making it unused.
Fixes: ce548396a4 ("media: mach-omap1: board-ams-delta.c: remove soc_camera dependencies")
Signed-off-by: Maciej Falkowski <maciej.falkowski9@gmail.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/1326
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d95f22798 upstream.
Here is the warning converted as error and reported by GCC:
kernel/static_call.c: In function ‘__static_call_update’:
kernel/static_call.c:153:18: error: unused variable ‘mod’ [-Werror=unused-variable]
153 | struct module *mod = site_mod->mod;
| ^~~
cc1: all warnings being treated as errors
make[1]: *** [scripts/Makefile.build:271: kernel/static_call.o] Error 1
This is simply because since recently, we no longer use 'mod' variable
elsewhere if MODULE is unset.
When using 'make tinyconfig' to generate the default kconfig, MODULE is
unset.
There are different ways to fix this warning. Here I tried to minimised
the number of modified lines and not add more #ifdef. We could also move
the declaration of the 'mod' variable inside the if-statement or
directly use site_mod->mod.
Fixes: 698bacefe9 ("static_call: Align static_call_is_init() patching condition")
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20210326105023.2058860-1-matthieu.baerts@tessares.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 064c734986 upstream.
The stat() family of syscalls report the wrong size for encrypted
symlinks, which has caused breakage in several userspace programs.
Fix this by calling fscrypt_symlink_getattr() after ubifs_getattr() for
encrypted symlinks. This function computes the correct size by reading
and decrypting the symlink target (if it's not already cached).
For more details, see the commit which added fscrypt_symlink_getattr().
Fixes: ca7f85be8d ("ubifs: Add support for encrypted symlinks")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210702065350.209646-5-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 461b43a8f9 upstream.
The stat() family of syscalls report the wrong size for encrypted
symlinks, which has caused breakage in several userspace programs.
Fix this by calling fscrypt_symlink_getattr() after f2fs_getattr() for
encrypted symlinks. This function computes the correct size by reading
and decrypting the symlink target (if it's not already cached).
For more details, see the commit which added fscrypt_symlink_getattr().
Fixes: cbaf042a3c ("f2fs crypto: add symlink encryption")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210702065350.209646-4-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c4bca10ce upstream.
The stat() family of syscalls report the wrong size for encrypted
symlinks, which has caused breakage in several userspace programs.
Fix this by calling fscrypt_symlink_getattr() after ext4_getattr() for
encrypted symlinks. This function computes the correct size by reading
and decrypting the symlink target (if it's not already cached).
For more details, see the commit which added fscrypt_symlink_getattr().
Fixes: f348c25232 ("ext4 crypto: add symlink encryption")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210702065350.209646-3-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d187605605 upstream.
Add a helper function fscrypt_symlink_getattr() which will be called
from the various filesystems' ->getattr() methods to read and decrypt
the target of encrypted symlinks in order to report the correct st_size.
Detailed explanation:
As required by POSIX and as documented in various man pages, st_size for
a symlink is supposed to be the length of the symlink target.
Unfortunately, st_size has always been wrong for encrypted symlinks
because st_size is populated from i_size from disk, which intentionally
contains the length of the encrypted symlink target. That's slightly
greater than the length of the decrypted symlink target (which is the
symlink target that userspace usually sees), and usually won't match the
length of the no-key encoded symlink target either.
This hadn't been fixed yet because reporting the correct st_size would
require reading the symlink target from disk and decrypting or encoding
it, which historically has been considered too heavyweight to do in
->getattr(). Also historically, the wrong st_size had only broken a
test (LTP lstat03) and there were no known complaints from real users.
(This is probably because the st_size of symlinks isn't used too often,
and when it is, typically it's for a hint for what buffer size to pass
to readlink() -- which a slightly-too-large size still works for.)
However, a couple things have changed now. First, there have recently
been complaints about the current behavior from real users:
- Breakage in rpmbuild:
https://github.com/rpm-software-management/rpm/issues/1682https://github.com/google/fscrypt/issues/305
- Breakage in toybox cpio:
https://www.mail-archive.com/toybox@lists.landley.net/msg07193.html
- Breakage in libgit2: https://issuetracker.google.com/issues/189629152
(on Android public issue tracker, requires login)
Second, we now cache decrypted symlink targets in ->i_link. Therefore,
taking the performance hit of reading and decrypting the symlink target
in ->getattr() wouldn't be as big a deal as it used to be, since usually
it will just save having to do the same thing later.
Also note that eCryptfs ended up having to read and decrypt symlink
targets in ->getattr() as well, to fix this same issue; see
commit 3a60a1686f ("eCryptfs: Decrypt symlink target for stat size").
So, let's just bite the bullet, and read and decrypt the symlink target
in ->getattr() in order to report the correct st_size. Add a function
fscrypt_symlink_getattr() which the filesystems will call to do this.
(Alternatively, we could store the decrypted size of symlinks on-disk.
But there isn't a great place to do so, and encryption is meant to hide
the original size to some extent; that property would be lost.)
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210702065350.209646-2-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a54c4613da upstream.
The location of the system.data extended attribute can change whenever
xattr_sem is not taken. So we need to recalculate the i_inline_off
field since it mgiht have changed between ext4_write_begin() and
ext4_write_end().
This means that caching i_inline_off is probably not helpful, so in
the long run we should probably get rid of it and shrink the in-memory
ext4 inode slightly, but let's fix the race the simple way for now.
Cc: stable@kernel.org
Fixes: f19d5870cb ("ext4: add normal write support for inline data")
Reported-by: syzbot+13146364637c7363a7de@syzkaller.appspotmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds an overlay to connect the QCA7000 in UART mode via UART0.
The qcauart driver uses the serial device bus instead of deprecated
line disciplines.
Signed-off-by: Stefan Wahren <stefan.wahren@in-tech.com>
commit a2baf4e8bb upstream.
Commit b910eaaaa4 ("bpf: Fix NULL pointer dereference in bpf_get_local_storage()
helper") fixed a bug for bpf_get_local_storage() helper so different tasks
won't mess up with each other's percpu local storage.
The percpu data contains 8 slots so it can hold up to 8 contexts (same or
different tasks), for 8 different program runs, at the same time. This in
general is sufficient. But our internal testing showed the following warning
multiple times:
[...]
warning: WARNING: CPU: 13 PID: 41661 at include/linux/bpf-cgroup.h:193
__cgroup_bpf_run_filter_sock_ops+0x13e/0x180
RIP: 0010:__cgroup_bpf_run_filter_sock_ops+0x13e/0x180
<IRQ>
tcp_call_bpf.constprop.99+0x93/0xc0
tcp_conn_request+0x41e/0xa50
? tcp_rcv_state_process+0x203/0xe00
tcp_rcv_state_process+0x203/0xe00
? sk_filter_trim_cap+0xbc/0x210
? tcp_v6_inbound_md5_hash.constprop.41+0x44/0x160
tcp_v6_do_rcv+0x181/0x3e0
tcp_v6_rcv+0xc65/0xcb0
ip6_protocol_deliver_rcu+0xbd/0x450
ip6_input_finish+0x11/0x20
ip6_input+0xb5/0xc0
ip6_sublist_rcv_finish+0x37/0x50
ip6_sublist_rcv+0x1dc/0x270
ipv6_list_rcv+0x113/0x140
__netif_receive_skb_list_core+0x1a0/0x210
netif_receive_skb_list_internal+0x186/0x2a0
gro_normal_list.part.170+0x19/0x40
napi_complete_done+0x65/0x150
mlx5e_napi_poll+0x1ae/0x680
__napi_poll+0x25/0x120
net_rx_action+0x11e/0x280
__do_softirq+0xbb/0x271
irq_exit_rcu+0x97/0xa0
common_interrupt+0x7f/0xa0
</IRQ>
asm_common_interrupt+0x1e/0x40
RIP: 0010:bpf_prog_1835a9241238291a_tw_egress+0x5/0xbac
? __cgroup_bpf_run_filter_skb+0x378/0x4e0
? do_softirq+0x34/0x70
? ip6_finish_output2+0x266/0x590
? ip6_finish_output+0x66/0xa0
? ip6_output+0x6c/0x130
? ip6_xmit+0x279/0x550
? ip6_dst_check+0x61/0xd0
[...]
Using drgn [0] to dump the percpu buffer contents showed that on this CPU
slot 0 is still available, but slots 1-7 are occupied and those tasks in
slots 1-7 mostly don't exist any more. So we might have issues in
bpf_cgroup_storage_unset().
Further debugging confirmed that there is a bug in bpf_cgroup_storage_unset().
Currently, it tries to unset "current" slot with searching from the start.
So the following sequence is possible:
1. A task is running and claims slot 0
2. Running BPF program is done, and it checked slot 0 has the "task"
and ready to reset it to NULL (not yet).
3. An interrupt happens, another BPF program runs and it claims slot 1
with the *same* task.
4. The unset() in interrupt context releases slot 0 since it matches "task".
5. Interrupt is done, the task in process context reset slot 0.
At the end, slot 1 is not reset and the same process can continue to occupy
slots 2-7 and finally, when the above step 1-5 is repeated again, step 3 BPF
program won't be able to claim an empty slot and a warning will be issued.
To fix the issue, for unset() function, we should traverse from the last slot
to the first. This way, the above issue can be avoided.
The same reverse traversal should also be done in bpf_get_local_storage() helper
itself. Otherwise, incorrect local storage may be returned to BPF program.
[0] https://github.com/osandov/drgn
Fixes: b910eaaaa4 ("bpf: Fix NULL pointer dereference in bpf_get_local_storage() helper")
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210810010413.1976277-1-yhs@fb.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67d69e9d1a upstream.
AUDIT_TRIM is expected to be idempotent, but multiple executions resulted
in a refcount underflow and use-after-free.
git bisect fingered commit fb041bb7c0 ("locking/refcount: Consolidate
implementations of refcount_t") but this patch with its more thorough
checking that wasn't in the x86 assembly code merely exposed a previously
existing tree refcount imbalance in the case of tree trimming code that
was refactored with prune_one() to remove a tree introduced in
commit 8432c70062 ("audit: Simplify locking around untag_chunk()")
Move the put_tree() to cover only the prune_one() case.
Passes audit-testsuite and 3 passes of "auditctl -t" with at least one
directory watch.
Cc: Jan Kara <jack@suse.cz>
Cc: Will Deacon <will@kernel.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Seiji Nishikawa <snishika@redhat.com>
Cc: stable@vger.kernel.org
Fixes: 8432c70062 ("audit: Simplify locking around untag_chunk()")
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Reviewed-by: Jan Kara <jack@suse.cz>
[PM: reformatted/cleaned-up the commit description]
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0efb16294 upstream.
A common implementation of isatty(3) involves calling a ioctl passing
a dummy struct argument and checking whether the syscall failed --
bionic and glibc use TCGETS (passing a struct termios), and musl uses
TIOCGWINSZ (passing a struct winsize). If the FD is a socket, we will
copy sizeof(struct ifreq) bytes of data from the argument and return
-EFAULT if that fails. The result is that the isatty implementations
may return a non-POSIX-compliant value in errno in the case where part
of the dummy struct argument is inaccessible, as both struct termios
and struct winsize are smaller than struct ifreq (at least on arm64).
Although there is usually enough stack space following the argument
on the stack that this did not present a practical problem up to now,
with MTE stack instrumentation it's more likely for the copy to fail,
as the memory following the struct may have a different tag.
Fix the problem by adding an early check for whether the ioctl is a
valid socket ioctl, and return -ENOTTY if it isn't.
Fixes: 44c02a2c3d ("dev_ioctl(): move copyin/copyout to callers")
Link: https://linux-review.googlesource.com/id/I869da6cf6daabc3e4b7b82ac979683ba05e27d4d
Signed-off-by: Peter Collingbourne <pcc@google.com>
Cc: <stable@vger.kernel.org> # 4.19
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a7956e25e upstream.
The kthread_is_per_cpu() construct relies on only being called on
PF_KTHREAD tasks (per the WARN in to_kthread). This gives rise to the
following usage pattern:
if ((p->flags & PF_KTHREAD) && kthread_is_per_cpu(p))
However, as reported by syzcaller, this is broken. The scenario is:
CPU0 CPU1 (running p)
(p->flags & PF_KTHREAD) // true
begin_new_exec()
me->flags &= ~(PF_KTHREAD|...);
kthread_is_per_cpu(p)
to_kthread(p)
WARN(!(p->flags & PF_KTHREAD) <-- *SPLAT*
Introduce __to_kthread() that omits the WARN and is sure to check both
values.
Use this to remove the problematic pattern for kthread_is_per_cpu()
and fix a number of other kthread_*() functions that have similar
issues but are currently not used in ways that would expose the
problem.
Notably kthread_func() is only ever called on 'current', while
kthread_probe_data() is only used for PF_WQ_WORKER, which implies the
task is from kthread_create*().
Fixes: ac687e6e8c ("kthread: Extract KTHREAD_IS_PER_CPU")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Valentin Schneider <Valentin.Schneider@arm.com>
Link: https://lkml.kernel.org/r/YH6WJc825C4P0FCK@hirez.programming.kicks-ass.net
[ Drop the balance_push() hunk as it is not needed. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4571b8c5e upstream.
[BUG]
It's easy to trigger NULL pointer dereference, just by removing a
non-existing device id:
# mkfs.btrfs -f -m single -d single /dev/test/scratch1 \
/dev/test/scratch2
# mount /dev/test/scratch1 /mnt/btrfs
# btrfs device remove 3 /mnt/btrfs
Then we have the following kernel NULL pointer dereference:
BUG: kernel NULL pointer dereference, address: 0000000000000000
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP NOPTI
CPU: 9 PID: 649 Comm: btrfs Not tainted 5.14.0-rc3-custom+ #35
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
RIP: 0010:btrfs_rm_device+0x4de/0x6b0 [btrfs]
btrfs_ioctl+0x18bb/0x3190 [btrfs]
? lock_is_held_type+0xa5/0x120
? find_held_lock.constprop.0+0x2b/0x80
? do_user_addr_fault+0x201/0x6a0
? lock_release+0xd2/0x2d0
? __x64_sys_ioctl+0x83/0xb0
__x64_sys_ioctl+0x83/0xb0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
[CAUSE]
Commit a27a94c2b0 ("btrfs: Make btrfs_find_device_by_devspec return
btrfs_device directly") moves the "missing" device path check into
btrfs_rm_device().
But btrfs_rm_device() itself can have case where it only receives
@devid, with NULL as @device_path.
In that case, calling strcmp() on NULL will trigger the NULL pointer
dereference.
Before that commit, we handle the "missing" case inside
btrfs_find_device_by_devspec(), which will not check @device_path at all
if @devid is provided, thus no way to trigger the bug.
[FIX]
Before calling strcmp(), also make sure @device_path is not NULL.
Fixes: a27a94c2b0 ("btrfs: Make btrfs_find_device_by_devspec return btrfs_device directly")
CC: stable@vger.kernel.org # 5.4+
Reported-by: butt3rflyh4ck <butterflyhuangxx@gmail.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7428022b50 upstream.
When a port leaves a VLAN-aware bridge, the current code does not clear
other ports' matrix field bit. If the bridge is later set to VLAN-unaware
mode, traffic in the bridge may leak to that port.
Remove the VLAN filtering check in mt7530_port_bridge_leave.
Fixes: 474a2ddaa1 ("net: dsa: mt7530: fix VLAN traffic leaks")
Fixes: 83163f7dca ("net: dsa: mediatek: add VLAN support for MT7530")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c9b3caab3 upstream.
It's possible that the interrupt handler for the UCSI driver signals a
connector changes after the handler clears the PENDING bit, but before
it has sent the acknowledge request. The result is that the handler is
invoked yet again, to ack the same connector change.
At least some versions of the Qualcomm UCSI firmware will not handle the
second - "spurious" - acknowledgment gracefully. So make sure to not
clear the pending flag until the change is acknowledged.
Any connector changes coming in after the acknowledgment, that would
have the pending flag incorrectly cleared, would afaict be covered by
the subsequent connector status check.
Fixes: 217504a055 ("usb: typec: ucsi: Work around PPM losing change information")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-By: Benjamin Berg <bberg@redhat.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210516040953.622409-1-bjorn.andersson@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 217504a055 upstream.
Some/many PPMs are simply clearing the change bitfield when a
notification on a port is acknowledge. Unfortunately, doing so means
that any changes between the GET_CONNECTOR_STATUS and ACK_CC_CI commands
is simply lost.
Work around this by re-fetching the connector status afterwards. We can
then infer any changes that we see have happened but that may not be
respresented in the change bitfield.
We end up with the following actions:
1. UCSI_GET_CONNECTOR_STATUS, store result, update unprocessed_changes
2. UCSI_GET_CAM_SUPPORTED, discard result
3. ACK connector change
4. UCSI_GET_CONNECTOR_STATUS, store result
5. Infere lost changes by comparing UCSI_GET_CONNECTOR_STATUS results
6. If PPM reported a new change, then restart in order to ACK
7. Process everything as usual.
The worker is also changed to re-schedule itself if a new change
notification happened while it was running.
Doing this fixes quite commonly occurring issues where e.g. the UCSI
power supply would remain online even thought the ThunderBolt cable was
unplugged.
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Benjamin Berg <bberg@redhat.com>
Link: https://lore.kernel.org/r/20201009144047.505957-3-benjamin@sipsolutions.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b40066c97 upstream.
State transitions from 1->0->1 and N->2->1 callbacks require RCU
synchronization. Rather than performing the RCU synchronization every
time the state change occurs, which is quite slow when many tracepoints
are registered in batch, instead keep a snapshot of the RCU state on the
most recent transitions which belong to a chain, and conditionally wait
for a grace period on the last transition of the chain if one g.p. has
not elapsed since the last snapshot.
This applies to both RCU and SRCU.
This brings the performance regression caused by commit 231264d692
("Fix: tracepoint: static call function vs data state mismatch") back to
what it was originally.
Before this commit:
# trace-cmd start -e all
# time trace-cmd start -p nop
real 0m10.593s
user 0m0.017s
sys 0m0.259s
After this commit:
# trace-cmd start -e all
# time trace-cmd start -p nop
real 0m0.878s
user 0m0.000s
sys 0m0.103s
Link: https://lkml.kernel.org/r/20210805192954.30688-1-mathieu.desnoyers@efficios.com
Link: https://lore.kernel.org/io-uring/4ebea8f0-58c9-e571-fd30-0ce4f6f09c70@samba.org/
Cc: stable@vger.kernel.org
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: "Paul E. McKenney" <paulmck@kernel.org>
Cc: Stefan Metzmacher <metze@samba.org>
Fixes: 231264d692 ("Fix: tracepoint: static call function vs data state mismatch")
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Reviewed-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b5bd67cf6 upstream.
There is a need for a polling interface for SRCU grace
periods, so this commit supplies get_state_synchronize_srcu(),
start_poll_synchronize_srcu(), and poll_state_synchronize_srcu() for this
purpose. The first can be used if future grace periods are inevitable
(perhaps due to a later call_srcu() invocation), the second if future
grace periods might not otherwise happen, and the third to check if a
grace period has elapsed since the corresponding call to either of the
first two.
As with get_state_synchronize_rcu() and cond_synchronize_rcu(),
the return value from either get_state_synchronize_srcu() or
start_poll_synchronize_srcu() must be passed in to a later call to
poll_state_synchronize_srcu().
Link: https://lore.kernel.org/rcu/20201112201547.GF3365678@moria.home.lan/
Reported-by: Kent Overstreet <kent.overstreet@gmail.com>
[ paulmck: Add EXPORT_SYMBOL_GPL() per kernel test robot feedback. ]
[ paulmck: Apply feedback from Neeraj Upadhyay. ]
Link: https://lore.kernel.org/lkml/20201117004017.GA7444@paulmck-ThinkPad-P72/
Reviewed-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 74612a07b8 upstream.
There is a need for a polling interface for SRCU grace periods. This
polling needs to distinguish between an SRCU instance being idle on the
one hand or in the middle of a grace period on the other. This commit
therefore converts the Tiny SRCU srcu_struct structure's srcu_idx from
a defacto boolean to a free-running counter, using the bottom bit to
indicate that a grace period is in progress. The second-from-bottom
bit is thus used as the index returned by srcu_read_lock().
Link: https://lore.kernel.org/rcu/20201112201547.GF3365678@moria.home.lan/
Reported-by: Kent Overstreet <kent.overstreet@gmail.com>
[ paulmck: Fix ->srcu_lock_nesting[] indexing per Neeraj Upadhyay. ]
Reviewed-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a893c711a upstream.
There is a need for a polling interface for SRCU grace periods.
This polling needs to initiate an SRCU grace period without
having to queue (and manage) a callback. This commit therefore
splits the Tiny SRCU call_srcu() function into callback-queuing and
start-grace-period portions, with the latter in a new function named
srcu_gp_start_if_needed().
Link: https://lore.kernel.org/rcu/20201112201547.GF3365678@moria.home.lan/
Reported-by: Kent Overstreet <kent.overstreet@gmail.com>
Reviewed-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5358c9fa54 upstream.
There is a need for a polling interface for SRCU grace
periods, so this commit supplies get_state_synchronize_srcu(),
start_poll_synchronize_srcu(), and poll_state_synchronize_srcu() for this
purpose. The first can be used if future grace periods are inevitable
(perhaps due to a later call_srcu() invocation), the second if future
grace periods might not otherwise happen, and the third to check if a
grace period has elapsed since the corresponding call to either of the
first two.
As with get_state_synchronize_rcu() and cond_synchronize_rcu(),
the return value from either get_state_synchronize_srcu() or
start_poll_synchronize_srcu() must be passed in to a later call to
poll_state_synchronize_srcu().
Link: https://lore.kernel.org/rcu/20201112201547.GF3365678@moria.home.lan/
Reported-by: Kent Overstreet <kent.overstreet@gmail.com>
[ paulmck: Add EXPORT_SYMBOL_GPL() per kernel test robot feedback. ]
[ paulmck: Apply feedback from Neeraj Upadhyay. ]
Link: https://lore.kernel.org/lkml/20201117004017.GA7444@paulmck-ThinkPad-P72/
Reviewed-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29d2bb94a8 upstream.
There is a need for a polling interface for SRCU grace periods.
This polling needs to initiate an SRCU grace period without having
to queue (and manage) a callback. This commit therefore splits the
Tree SRCU __call_srcu() function into callback-initialization and
queuing/start-grace-period portions, with the latter in a new function
named srcu_gp_start_if_needed(). This function may be passed a NULL
callback pointer, in which case it will refrain from queuing anything.
Why have the new function mess with queuing? Locking considerations,
of course!
Link: https://lore.kernel.org/rcu/20201112201547.GF3365678@moria.home.lan/
Reported-by: Kent Overstreet <kent.overstreet@gmail.com>
Reviewed-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f66de7ac48 upstream.
The power_pmu_event_init() callback access per-cpu variable
(cpu_hw_events) to check for event constraints and Branch Stack
(BHRB). Current usage is to disable preemption when accessing the
per-cpu variable, but this does not prevent timer callback from
interrupting event_init. Fix this by using 'local_irq_save/restore'
to make sure the code path is invoked with disabled interrupts.
This change is tested in mambo simulator to ensure that, if a timer
interrupt comes in during the per-cpu access in event_init, it will be
soft masked and replayed later. For testing purpose, introduced a
udelay() in power_pmu_event_init() to make sure a timer interrupt arrives
while in per-cpu variable access code between local_irq_save/resore.
As expected the timer interrupt was replayed later during local_irq_restore
called from power_pmu_event_init. This was confirmed by adding
breakpoint in mambo and checking the backtrace when timer_interrupt
was hit.
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1606814880-1720-1-git-send-email-atrajeev@linux.vnet.ibm.com
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f0e6edcd9 upstream.
Considering the following testcase:
int
foo(int a, int b)
{
for (unsigned i = 0; i < 1000000000; i++)
a += b;
return a;
}
int main()
{
foo (3, 4);
return 0;
}
'perf annotate' displays:
86.52 │40055e: → ja 40056c <foo(int, int)+0x26>
13.37 │400560: mov -0x18(%rbp),%eax
│400563: add %eax,-0x14(%rbp)
│400566: addl $0x1,-0x4(%rbp)
0.11 │40056a: → jmp 400557 <foo(int, int)+0x11>
│40056c: mov -0x14(%rbp),%eax
│40056f: pop %rbp
and the 'ja 40056c' does not link to the location in the function. It's
caused by fact that comma is wrongly parsed, it's part of function
signature.
With my patch I see:
86.52 │ ┌──ja 26
13.37 │ │ mov -0x18(%rbp),%eax
│ │ add %eax,-0x14(%rbp)
│ │ addl $0x1,-0x4(%rbp)
0.11 │ │↑ jmp 11
│26:└─→mov -0x14(%rbp),%eax
and 'o' output prints:
86.52 │4005┌── ↓ ja 40056c <foo(int, int)+0x26>
13.37 │4005│0: mov -0x18(%rbp),%eax
│4005│3: add %eax,-0x14(%rbp)
│4005│6: addl $0x1,-0x4(%rbp)
0.11 │4005│a: ↑ jmp 400557 <foo(int, int)+0x11>
│4005└─→ mov -0x14(%rbp),%eax
On the contrary, compiling the very same file with gcc -x c, the parsing
is fine because function arguments are not displayed:
jmp 400543 <foo+0x1d>
Committer testing:
Before:
$ cat cpp_args_annotate.c
int
foo(int a, int b)
{
for (unsigned i = 0; i < 1000000000; i++)
a += b;
return a;
}
int main()
{
foo (3, 4);
return 0;
}
$ gcc --version |& head -1
gcc (GCC) 10.2.1 20201125 (Red Hat 10.2.1-9)
$ gcc -g cpp_args_annotate.c -o cpp_args_annotate
$ perf record ./cpp_args_annotate
[ perf record: Woken up 2 times to write data ]
[ perf record: Captured and wrote 0.275 MB perf.data (7188 samples) ]
$ perf annotate --stdio2 foo
Samples: 7K of event 'cycles:u', 4000 Hz, Event count (approx.): 7468429289, [percent: local period]
foo() /home/acme/c/cpp_args_annotate
Percent
0000000000401106 <foo>:
foo():
int
foo(int a, int b)
{
push %rbp
mov %rsp,%rbp
mov %edi,-0x14(%rbp)
mov %esi,-0x18(%rbp)
for (unsigned i = 0; i < 1000000000; i++)
movl $0x0,-0x4(%rbp)
↓ jmp 1d
a += b;
13.45 13: mov -0x18(%rbp),%eax
add %eax,-0x14(%rbp)
for (unsigned i = 0; i < 1000000000; i++)
addl $0x1,-0x4(%rbp)
0.09 1d: cmpl $0x3b9ac9ff,-0x4(%rbp)
86.46 ↑ jbe 13
return a;
mov -0x14(%rbp),%eax
}
pop %rbp
← retq
$
I.e. works for C, now lets switch to C++:
$ g++ -g cpp_args_annotate.c -o cpp_args_annotate
$ perf record ./cpp_args_annotate
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.268 MB perf.data (6976 samples) ]
$ perf annotate --stdio2 foo
Samples: 6K of event 'cycles:u', 4000 Hz, Event count (approx.): 7380681761, [percent: local period]
foo() /home/acme/c/cpp_args_annotate
Percent
0000000000401106 <foo(int, int)>:
foo(int, int):
int
foo(int a, int b)
{
push %rbp
mov %rsp,%rbp
mov %edi,-0x14(%rbp)
mov %esi,-0x18(%rbp)
for (unsigned i = 0; i < 1000000000; i++)
movl $0x0,-0x4(%rbp)
cmpl $0x3b9ac9ff,-0x4(%rbp)
86.53 → ja 40112c <foo(int, int)+0x26>
a += b;
13.32 mov -0x18(%rbp),%eax
0.00 add %eax,-0x14(%rbp)
for (unsigned i = 0; i < 1000000000; i++)
addl $0x1,-0x4(%rbp)
0.15 → jmp 401117 <foo(int, int)+0x11>
return a;
mov -0x14(%rbp),%eax
}
pop %rbp
← retq
$
Reproduced.
Now with this patch:
Reusing the C++ built binary, as we can see here:
$ readelf -wi cpp_args_annotate | grep producer
<c> DW_AT_producer : (indirect string, offset: 0x2e): GNU C++14 10.2.1 20201125 (Red Hat 10.2.1-9) -mtune=generic -march=x86-64 -g
$
And furthermore:
$ file cpp_args_annotate
cpp_args_annotate: ELF 64-bit LSB executable, x86-64, version 1 (SYSV), dynamically linked, interpreter /lib64/ld-linux-x86-64.so.2, BuildID[sha1]=4fe3cab260204765605ec630d0dc7a7e93c361a9, for GNU/Linux 3.2.0, with debug_info, not stripped
$ perf buildid-list -i cpp_args_annotate
4fe3cab260204765605ec630d0dc7a7e93c361a9
$ perf buildid-list | grep cpp_args_annotate
4fe3cab260204765605ec630d0dc7a7e93c361a9 /home/acme/c/cpp_args_annotate
$
It now works:
$ perf annotate --stdio2 foo
Samples: 6K of event 'cycles:u', 4000 Hz, Event count (approx.): 7380681761, [percent: local period]
foo() /home/acme/c/cpp_args_annotate
Percent
0000000000401106 <foo(int, int)>:
foo(int, int):
int
foo(int a, int b)
{
push %rbp
mov %rsp,%rbp
mov %edi,-0x14(%rbp)
mov %esi,-0x18(%rbp)
for (unsigned i = 0; i < 1000000000; i++)
movl $0x0,-0x4(%rbp)
11: cmpl $0x3b9ac9ff,-0x4(%rbp)
86.53 ↓ ja 26
a += b;
13.32 mov -0x18(%rbp),%eax
0.00 add %eax,-0x14(%rbp)
for (unsigned i = 0; i < 1000000000; i++)
addl $0x1,-0x4(%rbp)
0.15 ↑ jmp 11
return a;
26: mov -0x14(%rbp),%eax
}
pop %rbp
← retq
$
Signed-off-by: Martin Liška <mliska@suse.cz>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Link: http://lore.kernel.org/lkml/13e1a405-edf9-e4c2-4327-a9b454353730@suse.cz
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 41d5854113 upstream.
I got several memory leak reports from Asan with a simple command. It
was because VDSO is not released due to the refcount. Like in
__dsos_addnew_id(), it should put the refcount after adding to the list.
$ perf record true
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.030 MB perf.data (10 samples) ]
=================================================================
==692599==ERROR: LeakSanitizer: detected memory leaks
Direct leak of 439 byte(s) in 1 object(s) allocated from:
#0 0x7fea52341037 in __interceptor_calloc ../../../../src/libsanitizer/asan/asan_malloc_linux.cpp:154
#1 0x559bce4aa8ee in dso__new_id util/dso.c:1256
#2 0x559bce59245a in __machine__addnew_vdso util/vdso.c:132
#3 0x559bce59245a in machine__findnew_vdso util/vdso.c:347
#4 0x559bce50826c in map__new util/map.c:175
#5 0x559bce503c92 in machine__process_mmap2_event util/machine.c:1787
#6 0x559bce512f6b in machines__deliver_event util/session.c:1481
#7 0x559bce515107 in perf_session__deliver_event util/session.c:1551
#8 0x559bce51d4d2 in do_flush util/ordered-events.c:244
#9 0x559bce51d4d2 in __ordered_events__flush util/ordered-events.c:323
#10 0x559bce519bea in __perf_session__process_events util/session.c:2268
#11 0x559bce519bea in perf_session__process_events util/session.c:2297
#12 0x559bce2e7a52 in process_buildids /home/namhyung/project/linux/tools/perf/builtin-record.c:1017
#13 0x559bce2e7a52 in record__finish_output /home/namhyung/project/linux/tools/perf/builtin-record.c:1234
#14 0x559bce2ed4f6 in __cmd_record /home/namhyung/project/linux/tools/perf/builtin-record.c:2026
#15 0x559bce2ed4f6 in cmd_record /home/namhyung/project/linux/tools/perf/builtin-record.c:2858
#16 0x559bce422db4 in run_builtin /home/namhyung/project/linux/tools/perf/perf.c:313
#17 0x559bce2acac8 in handle_internal_command /home/namhyung/project/linux/tools/perf/perf.c:365
#18 0x559bce2acac8 in run_argv /home/namhyung/project/linux/tools/perf/perf.c:409
#19 0x559bce2acac8 in main /home/namhyung/project/linux/tools/perf/perf.c:539
#20 0x7fea51e76d09 in __libc_start_main ../csu/libc-start.c:308
Indirect leak of 32 byte(s) in 1 object(s) allocated from:
#0 0x7fea52341037 in __interceptor_calloc ../../../../src/libsanitizer/asan/asan_malloc_linux.cpp:154
#1 0x559bce520907 in nsinfo__copy util/namespaces.c:169
#2 0x559bce50821b in map__new util/map.c:168
#3 0x559bce503c92 in machine__process_mmap2_event util/machine.c:1787
#4 0x559bce512f6b in machines__deliver_event util/session.c:1481
#5 0x559bce515107 in perf_session__deliver_event util/session.c:1551
#6 0x559bce51d4d2 in do_flush util/ordered-events.c:244
#7 0x559bce51d4d2 in __ordered_events__flush util/ordered-events.c:323
#8 0x559bce519bea in __perf_session__process_events util/session.c:2268
#9 0x559bce519bea in perf_session__process_events util/session.c:2297
#10 0x559bce2e7a52 in process_buildids /home/namhyung/project/linux/tools/perf/builtin-record.c:1017
#11 0x559bce2e7a52 in record__finish_output /home/namhyung/project/linux/tools/perf/builtin-record.c:1234
#12 0x559bce2ed4f6 in __cmd_record /home/namhyung/project/linux/tools/perf/builtin-record.c:2026
#13 0x559bce2ed4f6 in cmd_record /home/namhyung/project/linux/tools/perf/builtin-record.c:2858
#14 0x559bce422db4 in run_builtin /home/namhyung/project/linux/tools/perf/perf.c:313
#15 0x559bce2acac8 in handle_internal_command /home/namhyung/project/linux/tools/perf/perf.c:365
#16 0x559bce2acac8 in run_argv /home/namhyung/project/linux/tools/perf/perf.c:409
#17 0x559bce2acac8 in main /home/namhyung/project/linux/tools/perf/perf.c:539
#18 0x7fea51e76d09 in __libc_start_main ../csu/libc-start.c:308
SUMMARY: AddressSanitizer: 471 byte(s) leaked in 2 allocation(s).
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20210315045641.700430-1-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67069a1f0f upstream.
ASan reported a memory leak caused by info_linear not being deallocated.
The info_linear was allocated during in perf_event__synthesize_one_bpf_prog().
This patch adds the corresponding free() when bpf_prog_info_node
is freed in perf_env__purge_bpf().
$ sudo ./perf record -- sleep 5
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.025 MB perf.data (8 samples) ]
=================================================================
==297735==ERROR: LeakSanitizer: detected memory leaks
Direct leak of 7688 byte(s) in 19 object(s) allocated from:
#0 0x4f420f in malloc (/home/user/linux/tools/perf/perf+0x4f420f)
#1 0xc06a74 in bpf_program__get_prog_info_linear /home/user/linux/tools/lib/bpf/libbpf.c:11113:16
#2 0xb426fe in perf_event__synthesize_one_bpf_prog /home/user/linux/tools/perf/util/bpf-event.c:191:16
#3 0xb42008 in perf_event__synthesize_bpf_events /home/user/linux/tools/perf/util/bpf-event.c:410:9
#4 0x594596 in record__synthesize /home/user/linux/tools/perf/builtin-record.c:1490:8
#5 0x58c9ac in __cmd_record /home/user/linux/tools/perf/builtin-record.c:1798:8
#6 0x58990b in cmd_record /home/user/linux/tools/perf/builtin-record.c:2901:8
#7 0x7b2a20 in run_builtin /home/user/linux/tools/perf/perf.c:313:11
#8 0x7b12ff in handle_internal_command /home/user/linux/tools/perf/perf.c:365:8
#9 0x7b2583 in run_argv /home/user/linux/tools/perf/perf.c:409:2
#10 0x7b0d79 in main /home/user/linux/tools/perf/perf.c:539:3
#11 0x7fa357ef6b74 in __libc_start_main /usr/src/debug/glibc-2.33-8.fc34.x86_64/csu/../csu/libc-start.c:332:16
Signed-off-by: Riccardo Mancini <rickyman7@gmail.com>
Acked-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Andrii Nakryiko <andrii@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: KP Singh <kpsingh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: Yonghong Song <yhs@fb.com>
Link: http://lore.kernel.org/lkml/20210602224024.300485-1-rickyman7@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 55981d3541 upstream.
Some USB BT adapters don't satisfy the MTU requirement mentioned in
commit e848dbd364 ("Bluetooth: btusb: Add support USB ALT 3 for WBS")
and have ALT 3 setting that produces no/garbled audio. Some adapters
with larger MTU were also reported to have problems with ALT 3.
Add a flag and check it and MTU before selecting ALT 3, falling back to
ALT 1. Enable the flag for Realtek, restoring the previous behavior for
non-Realtek devices.
Tested with USB adapters (mtu<72, no/garbled sound with ALT3, ALT1
works) BCM20702A1 0b05:17cb, CSR8510A10 0a12:0001, and (mtu>=72, ALT3
works) RTL8761BU 0bda:8771, Intel AX200 8087:0029 (after disabling
ALT6). Also got reports for (mtu>=72, ALT 3 reported to produce bad
audio) Intel 8087:0a2b.
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Fixes: e848dbd364 ("Bluetooth: btusb: Add support USB ALT 3 for WBS")
Tested-by: Michał Kępień <kernel@kempniu.pl>
Tested-by: Jonathan Lampérth <jon@h4n.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7387a72c5f upstream.
__tipc_sendmsg() is called to send SYN packet by either tipc_sendmsg()
or tipc_connect(). The difference is in tipc_connect(), it will call
tipc_wait_for_connect() after __tipc_sendmsg() to wait until connecting
is done. So there's no need to wait in __tipc_sendmsg() for this case.
This patch is to fix it by calling tipc_wait_for_connect() only when dlen
is not 0 in __tipc_sendmsg(), which means it's called by tipc_connect().
Note this also fixes the failure in tipcutils/test/ptts/:
# ./tipcTS &
# ./tipcTC 9
(hang)
Fixes: 36239dab6da7 ("tipc: fix implicit-connect for SYN+")
Reported-by: Shuang Li <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new generic NAND ECC framework stores the configuration and
requirements in separate places since commit 93ef92f6f4 ("mtd: nand: Use
the new generic ECC object"). In 5.10.x The SPI NAND layer still uses only
the requirements to track the ECC properties. This mismatch leads to
values of zero being used for ECC strength and step_size in the SPI NAND
layer wherever nanddev_get_ecc_conf() is used and therefore breaks the SPI
NAND on-die ECC support in 5.10.x.
By using nanddev_get_ecc_requirements() instead of nanddev_get_ecc_conf()
for SPI NAND, we make sure that the correct parameters for the detected
chip are used. In later versions (5.11.x) this is fixed anyway with the
implementation of the SPI NAND on-die ECC engine.
Cc: stable@vger.kernel.org # 5.10.x
Reported-by: voice INTER connect GmbH <developer@voiceinterconnect.de>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe67f4dd8d upstream.
It turns out that the SIGIO/FASYNC situation is almost exactly the same
as the EPOLLET case was: user space really wants to be notified after
every operation.
Now, in a perfect world it should be sufficient to only notify user
space on "state transitions" when the IO state changes (ie when a pipe
goes from unreadable to readable, or from unwritable to writable). User
space should then do as much as possible - fully emptying the buffer or
what not - and we'll notify it again the next time the state changes.
But as with EPOLLET, we have at least one case (stress-ng) where the
kernel sent SIGIO due to the pipe being marked for asynchronous
notification, but the user space signal handler then didn't actually
necessarily read it all before returning (it read more than what was
written, but since there could be multiple writes, it could leave data
pending).
The user space code then expected to get another SIGIO for subsequent
writes - even though the pipe had been readable the whole time - and
would only then read more.
This is arguably a user space bug - and Colin King already fixed the
stress-ng code in question - but the kernel regression rules are clear:
it doesn't matter if kernel people think that user space did something
silly and wrong. What matters is that it used to work.
So if user space depends on specific historical kernel behavior, it's a
regression when that behavior changes. It's on us: we were silly to
have that non-optimal historical behavior, and our old kernel behavior
was what user space was tested against.
Because of how the FASYNC notification was tied to wakeup behavior, this
was first broken by commits f467a6a664 and 1b6b26ae70 ("pipe: fix
and clarify pipe read/write wakeup logic"), but at the time it seems
nobody noticed. Probably because the stress-ng problem case ends up
being timing-dependent too.
It was then unwittingly fixed by commit 3a34b13a88 ("pipe: make pipe
writes always wake up readers") only to be broken again when by commit
3b844826b6 ("pipe: avoid unnecessary EPOLLET wakeups under normal
loads").
And at that point the kernel test robot noticed the performance
refression in the stress-ng.sigio.ops_per_sec case. So the "Fixes" tag
below is somewhat ad hoc, but it matches when the issue was noticed.
Fix it for good (knock wood) by simply making the kill_fasync() case
separate from the wakeup case. FASYNC is quite rare, and we clearly
shouldn't even try to use the "avoid unnecessary wakeups" logic for it.
Link: https://lore.kernel.org/lkml/20210824151337.GC27667@xsang-OptiPlex-9020/
Fixes: 3b844826b6 ("pipe: avoid unnecessary EPOLLET wakeups under normal loads")
Reported-by: kernel test robot <oliver.sang@intel.com>
Tested-by: Oliver Sang <oliver.sang@intel.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b844826b6 upstream.
I had forgotten just how sensitive hackbench is to extra pipe wakeups,
and commit 3a34b13a88 ("pipe: make pipe writes always wake up
readers") ended up causing a quite noticeable regression on larger
machines.
Now, hackbench isn't necessarily a hugely meaningful benchmark, and it's
not clear that this matters in real life all that much, but as Mel
points out, it's used often enough when comparing kernels and so the
performance regression shows up like a sore thumb.
It's easy enough to fix at least for the common cases where pipes are
used purely for data transfer, and you never have any exciting poll
usage at all. So set a special 'poll_usage' flag when there is polling
activity, and make the ugly "EPOLLET has crazy legacy expectations"
semantics explicit to only that case.
I would love to limit it to just the broken EPOLLET case, but the pipe
code can't see the difference between epoll and regular select/poll, so
any non-read/write waiting will trigger the extra wakeup behavior. That
is sufficient for at least the hackbench case.
Apart from making the odd extra wakeup cases more explicitly about
EPOLLET, this also makes the extra wakeup be at the _end_ of the pipe
write, not at the first write chunk. That is actually much saner
semantics (as much as you can call any of the legacy edge-triggered
expectations for EPOLLET "sane") since it means that you know the wakeup
will happen once the write is done, rather than possibly in the middle
of one.
[ For stable people: I'm putting a "Fixes" tag on this, but I leave it
up to you to decide whether you actually want to backport it or not.
It likely has no impact outside of synthetic benchmarks - Linus ]
Link: https://lore.kernel.org/lkml/20210802024945.GA8372@xsang-OptiPlex-9020/
Fixes: 3a34b13a88 ("pipe: make pipe writes always wake up readers")
Reported-by: kernel test robot <oliver.sang@intel.com>
Tested-by: Sandeep Patil <sspatil@android.com>
Tested-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc0939fcfa upstream.
We have a race between marking that an inode needs to be logged, either
at btrfs_set_inode_last_trans() or at btrfs_page_mkwrite(), and between
btrfs_sync_log(). The following steps describe how the race happens.
1) We are at transaction N;
2) Inode I was previously fsynced in the current transaction so it has:
inode->logged_trans set to N;
3) The inode's root currently has:
root->log_transid set to 1
root->last_log_commit set to 0
Which means only one log transaction was committed to far, log
transaction 0. When a log tree is created we set ->log_transid and
->last_log_commit of its parent root to 0 (at btrfs_add_log_tree());
4) One more range of pages is dirtied in inode I;
5) Some task A starts an fsync against some other inode J (same root), and
so it joins log transaction 1.
Before task A calls btrfs_sync_log()...
6) Task B starts an fsync against inode I, which currently has the full
sync flag set, so it starts delalloc and waits for the ordered extent
to complete before calling btrfs_inode_in_log() at btrfs_sync_file();
7) During ordered extent completion we have btrfs_update_inode() called
against inode I, which in turn calls btrfs_set_inode_last_trans(),
which does the following:
spin_lock(&inode->lock);
inode->last_trans = trans->transaction->transid;
inode->last_sub_trans = inode->root->log_transid;
inode->last_log_commit = inode->root->last_log_commit;
spin_unlock(&inode->lock);
So ->last_trans is set to N and ->last_sub_trans set to 1.
But before setting ->last_log_commit...
8) Task A is at btrfs_sync_log():
- it increments root->log_transid to 2
- starts writeback for all log tree extent buffers
- waits for the writeback to complete
- writes the super blocks
- updates root->last_log_commit to 1
It's a lot of slow steps between updating root->log_transid and
root->last_log_commit;
9) The task doing the ordered extent completion, currently at
btrfs_set_inode_last_trans(), then finally runs:
inode->last_log_commit = inode->root->last_log_commit;
spin_unlock(&inode->lock);
Which results in inode->last_log_commit being set to 1.
The ordered extent completes;
10) Task B is resumed, and it calls btrfs_inode_in_log() which returns
true because we have all the following conditions met:
inode->logged_trans == N which matches fs_info->generation &&
inode->last_subtrans (1) <= inode->last_log_commit (1) &&
inode->last_subtrans (1) <= root->last_log_commit (1) &&
list inode->extent_tree.modified_extents is empty
And as a consequence we return without logging the inode, so the
existing logged version of the inode does not point to the extent
that was written after the previous fsync.
It should be impossible in practice for one task be able to do so much
progress in btrfs_sync_log() while another task is at
btrfs_set_inode_last_trans() right after it reads root->log_transid and
before it reads root->last_log_commit. Even if kernel preemption is enabled
we know the task at btrfs_set_inode_last_trans() can not be preempted
because it is holding the inode's spinlock.
However there is another place where we do the same without holding the
spinlock, which is in the memory mapped write path at:
vm_fault_t btrfs_page_mkwrite(struct vm_fault *vmf)
{
(...)
BTRFS_I(inode)->last_trans = fs_info->generation;
BTRFS_I(inode)->last_sub_trans = BTRFS_I(inode)->root->log_transid;
BTRFS_I(inode)->last_log_commit = BTRFS_I(inode)->root->last_log_commit;
(...)
So with preemption happening after setting ->last_sub_trans and before
setting ->last_log_commit, it is less of a stretch to have another task
do enough progress at btrfs_sync_log() such that the task doing the memory
mapped write ends up with ->last_sub_trans and ->last_log_commit set to
the same value. It is still a big stretch to get there, as the task doing
btrfs_sync_log() has to start writeback, wait for its completion and write
the super blocks.
So fix this in two different ways:
1) For btrfs_set_inode_last_trans(), simply set ->last_log_commit to the
value of ->last_sub_trans minus 1;
2) For btrfs_page_mkwrite() only set the inode's ->last_sub_trans, just
like we do for buffered and direct writes at btrfs_file_write_iter(),
which is all we need to make sure multiple writes and fsyncs to an
inode in the same transaction never result in an fsync missing that
the inode changed and needs to be logged. Turn this into a helper
function and use it both at btrfs_page_mkwrite() and at
btrfs_file_write_iter() - this also fixes the problem that at
btrfs_page_mkwrite() we were setting those fields without the
protection of the inode's spinlock.
This is an extremely unlikely race to happen in practice.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fb4b1373dc ]
Function "dma_map_sg" is entitled to merge adjacent entries
and return a value smaller than what was passed as "nents".
Subsequently "ib_map_mr_sg" needs to work with this value ("sg_dma_len")
rather than the original "nents" parameter ("sg_len").
This old RDS bug was exposed and reliably causes kernel panics
(using RDMA operations "rds-stress -D") on x86_64 starting with:
commit c588072bba ("iommu/vt-d: Convert intel iommu driver to the iommu ops")
Simply put: Linux 5.11 and later.
Signed-off-by: Gerd Rausch <gerd.rausch@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Link: https://lore.kernel.org/r/60efc69f-1f35-529d-a7ef-da0549cad143@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6eaa1f3c59 ]
When booted with multiple displays attached, the EFI GOP driver on (at
least) Ampere, can leave DP links powered up that aren't being used to
display anything. This confuses our tracking of SOR routing, with the
likely result being a failed modeset and display engine hang.
Fix this by (ab?)using the DisableLT IED script to power-down the link,
restoring HW to a state the driver expects.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa0b1ef5f7 ]
[Why]
Userspace should get back a copy of drm_wait_vblank that's been modified
even when drm_wait_vblank_ioctl returns a failure.
Rationale:
drm_wait_vblank_ioctl modifies the request and expects the user to read
it back. When the type is RELATIVE, it modifies it to ABSOLUTE and updates
the sequence to become current_vblank_count + sequence (which was
RELATIVE), but now it became ABSOLUTE.
drmWaitVBlank (in libdrm) expects this to be the case as it modifies
the request to be Absolute so it expects the sequence to would have been
updated.
The change is in compat_drm_wait_vblank, which is called by
drm_compat_ioctl. This change of copying the data back regardless of the
return number makes it en par with drm_ioctl, which always copies the
data before returning.
[How]
Return from the function after everything has been copied to user.
Fixes IGT:kms_flip::modeset-vs-vblank-race-interruptible
Tested on ChromeOS Trogdor(msm)
Reviewed-by: Michel Dänzer <mdaenzer@redhat.com>
Signed-off-by: Mark Yacoub <markyacoub@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210812194917.1703356-1-markyacoub@chromium.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37110237f3 ]
Avoiding qed ll2 race condition and NULL pointer dereference as part
of the remove and recovery flows.
Changes form V1:
- Change (!p_rx->set_prod_addr).
- qed_ll2.c checkpatch fixes.
Change from V2:
- Revert "qed_ll2.c checkpatch fixes".
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a24ce06c70 ]
We use a spinlock now so add a stub.
Ignore bogus uninitialized variable warnings.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e74cfa91f4 ]
As __vringh_iov() traverses a descriptor chain, it populates
each descriptor entry into either read or write vring iov
and increments that iov's ->used member. So, as we iterate
over a descriptor chain, at any point, (riov/wriov)->used
value gives the number of descriptor enteries available,
which are to be read or written by the device. As all read
iovs must precede the write iovs, wiov->used should be zero
when we are traversing a read descriptor. Current code checks
for wiov->i, to figure out whether any previous entry in the
current descriptor chain was a write descriptor. However,
iov->i is only incremented, when these vring iovs are consumed,
at a later point, and remain 0 in __vringh_iov(). So, correct
the check for read and write descriptor order, to use
wiov->used.
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Link: https://lore.kernel.org/r/1624591502-4827-1-git-send-email-neeraju@codeaurora.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43bb40c5b9 ]
When a virtio pci device undergo surprise removal (aka async removal in
PCIe spec), mark the device as broken so that any upper layer drivers can
abort any outstanding operation.
When a virtio net pci device undergo surprise removal which is used by a
NetworkManager, a below call trace was observed.
kernel:watchdog: BUG: soft lockup - CPU#1 stuck for 26s! [kworker/1:1:27059]
watchdog: BUG: soft lockup - CPU#1 stuck for 52s! [kworker/1:1:27059]
CPU: 1 PID: 27059 Comm: kworker/1:1 Tainted: G S W I L 5.13.0-hotplug+ #8
Hardware name: Dell Inc. PowerEdge R640/0H28RR, BIOS 2.9.4 11/06/2020
Workqueue: events linkwatch_event
RIP: 0010:virtnet_send_command+0xfc/0x150 [virtio_net]
Call Trace:
virtnet_set_rx_mode+0xcf/0x2a7 [virtio_net]
? __hw_addr_create_ex+0x85/0xc0
__dev_mc_add+0x72/0x80
igmp6_group_added+0xa7/0xd0
ipv6_mc_up+0x3c/0x60
ipv6_find_idev+0x36/0x80
addrconf_add_dev+0x1e/0xa0
addrconf_dev_config+0x71/0x130
addrconf_notify+0x1f5/0xb40
? rtnl_is_locked+0x11/0x20
? __switch_to_asm+0x42/0x70
? finish_task_switch+0xaf/0x2c0
? raw_notifier_call_chain+0x3e/0x50
raw_notifier_call_chain+0x3e/0x50
netdev_state_change+0x67/0x90
linkwatch_do_dev+0x3c/0x50
__linkwatch_run_queue+0xd2/0x220
linkwatch_event+0x21/0x30
process_one_work+0x1c8/0x370
worker_thread+0x30/0x380
? process_one_work+0x370/0x370
kthread+0x118/0x140
? set_kthread_struct+0x40/0x40
ret_from_fork+0x1f/0x30
Hence, add the ability to abort the command on surprise removal
which prevents infinite loop and system lockup.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Link: https://lore.kernel.org/r/20210721142648.1525924-5-parav@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60f0779862 ]
Currently vq->broken field is read by virtqueue_is_broken() in busy
loop in one context by virtnet_send_command().
vq->broken is set to true in other process context by
virtio_break_device(). Reader and writer are accessing it without any
synchronization. This may lead to a compiler optimization which may
result to optimize reading vq->broken only once.
Hence, force reading vq->broken on each invocation of
virtqueue_is_broken() and also force writing it so that such
update is visible to the readers.
It is a theoretical fix that isn't yet encountered in the field.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Link: https://lore.kernel.org/r/20210721142648.1525924-2-parav@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 335ffab3ef ]
This WARN can be triggered per-core and the stack trace is not useful.
Replace it with plain dev_err(). Fix a comment while at it.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1669a941f7 ]
The probe was manually passing NULL instead of dev to devm_clk_hw_register.
This caused a Unable to handle kernel NULL pointer dereference error.
Fix this by passing 'dev'.
Signed-off-by: Adam Ford <aford173@gmail.com>
Fixes: a20a40a8bb ("clk: renesas: rcar-usb2-clock-sel: Fix error handling in .probe()")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b3a8738b7 ]
The u32 variable pci_dword is being masked with 0x1fffffff and then left
shifted 23 places. The shift is a u32 operation,so a value of 0x200 or
more in pci_dword will overflow the u32 and only the bottow 32 bits
are assigned to addr. I don't believe this was the original intent.
Fix this by casting pci_dword to a resource_size_t to ensure no
overflow occurs.
Note that the mask and 12 bit left shift operation does not need this
because the mask SNR_IMC_MMIO_MEM0_MASK and shift is always a 32 bit
value.
Fixes: ee49532b38 ("perf/x86/intel/uncore: Add IMC uncore support for Snow Ridge")
Addresses-Coverity: ("Unintentional integer overflow")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Link: https://lore.kernel.org/r/20210706114553.28249-1-colin.king@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c8094e394 ]
When the schema fixups are applied to 'select' the result is a single
entry is required for a match, but that will never match as there should
be 2 entries. Also, a 'select' schema should have the widest possible
match, so use 'contains' which matches the compatible string(s) in any
position and not just the first position.
Fixes: 993dcfac64 ("dt-bindings: riscv: sifive-l2-cache: convert bindings to json-schema")
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 82a44ae113 ]
In the case of taprio offload is not enabled, the error handling path
causes a kernel crash due to kernel NULL pointer deference.
Fix this by adding check for NULL before attempt to access 'plat->est'
on the mutex_lock() call.
The following kernel panic is observed without this patch:
RIP: 0010:mutex_lock+0x10/0x20
Call Trace:
tc_setup_taprio+0x482/0x560 [stmmac]
kmem_cache_alloc_trace+0x13f/0x490
taprio_disable_offload.isra.0+0x9d/0x180 [sch_taprio]
taprio_destroy+0x6c/0x100 [sch_taprio]
qdisc_create+0x2e5/0x4f0
tc_modify_qdisc+0x126/0x740
rtnetlink_rcv_msg+0x12b/0x380
_raw_spin_lock_irqsave+0x19/0x40
_raw_spin_unlock_irqrestore+0x18/0x30
create_object+0x212/0x340
rtnl_calcit.isra.0+0x110/0x110
netlink_rcv_skb+0x50/0x100
netlink_unicast+0x191/0x230
netlink_sendmsg+0x243/0x470
sock_sendmsg+0x5e/0x60
____sys_sendmsg+0x20b/0x280
copy_msghdr_from_user+0x5c/0x90
__mod_memcg_state+0x87/0xf0
___sys_sendmsg+0x7c/0xc0
lru_cache_add+0x7f/0xa0
_raw_spin_unlock+0x16/0x30
wp_page_copy+0x449/0x890
handle_mm_fault+0x921/0xfc0
__sys_sendmsg+0x59/0xa0
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xa9
---[ end trace b1f19b24368a96aa ]---
Fixes: b60189e039 ("net: stmmac: Integrate EST with TAPRIO scheduler API")
Cc: <stable@vger.kernel.org> # 5.10.x
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2aae654a4 ]
Add a mutex lock to protect est structure parameters so that the
EST parameters can be updated by other threads.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pavel Machek (CIP) <pavel@denx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 885814a97f ]
This reverts commit 419dd626e3.
It turned out that the change from the reverted commit breaks the ACPI
based rpi's because it causes the 100Mhz max clock to be overridden to the
return from sdhci_iproc_get_max_clock(), which is 0 because there isn't a
OF/DT based clock device.
Reported-by: Jeremy Linton <jeremy.linton@arm.com>
Fixes: 419dd626e3 ("mmc: sdhci-iproc: Set SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN on BCM2711")
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c1671e0d1 ]
Currently, when query PFC configuration by dcbtool, driver will return
PFC enable status based on TC. As all priorities are mapped to TC0 by
default, if TC0 is enabled, then all priorities mapped to TC0 will be
shown as enabled status when query PFC setting, even though some
priorities have never been set.
for example:
$ dcb pfc show dev eth0
pfc-cap 4 macsec-bypass off delay 0
prio-pfc 0:off 1:off 2:off 3:off 4:off 5:off 6:off 7:off
$ dcb pfc set dev eth0 prio-pfc 0:on 1:on 2:on 3:on
$ dcb pfc show dev eth0
pfc-cap 4 macsec-bypass off delay 0
prio-pfc 0:on 1:on 2:on 3:on 4:on 5:on 6:on 7:on
To fix this problem, just returns user's PFC config parameter saved in
driver.
Fixes: cacde272dd ("net: hns3: Add hclge_dcb module for the support of DCB feature")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94391fae82 ]
VLAN list should not be added duplicate VLAN node, otherwise it would
cause "add failed" when restore VLAN from VLAN list, so this patch adds
VLAN ID check before adding node into VLAN list.
Fixes: c6075b1934 ("net: hns3: Record VF vlan tables")
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a96d9330b0 ]
After the cmdq registers are cleared, the firmware may take time to
clear out possible left over commands in the cmdq. Driver must release
cmdq memory only after firmware has completed processing of left over
commands.
Fixes: 232d0d55fc ("net: hns3: uninitialize command queue while unloading PF driver")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a6d281946 ]
If a PF is bonded to a virtual machine and the virtual machine exits
unexpectedly, some hardware resource cannot be cleared. In this case,
loading driver may cause exceptions. Therefore, the hardware resource
needs to be cleared when the driver is loaded.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 96a6b93b69 ]
Currently when device is moved between network namespaces using
RTM_NEWLINK message type and one of netns attributes (FLA_NET_NS_PID,
IFLA_NET_NS_FD, IFLA_TARGET_NETNSID) but w/o specifying IFLA_IFNAME, and
target namespace already has device with same name, userspace will get
EINVAL what is confusing and makes debugging harder.
Fix it so that userspace gets more appropriate EEXIST instead what makes
debugging much easier.
Before:
# ./ifname.sh
+ ip netns add ns0
+ ip netns exec ns0 ip link add l0 type dummy
+ ip netns exec ns0 ip link show l0
8: l0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 66:90:b5:d5:78:69 brd ff:ff:ff:ff:ff:ff
+ ip link add l0 type dummy
+ ip link show l0
10: l0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 6e:c6:1f:15:20:8d brd ff:ff:ff:ff:ff:ff
+ ip link set l0 netns ns0
RTNETLINK answers: Invalid argument
After:
# ./ifname.sh
+ ip netns add ns0
+ ip netns exec ns0 ip link add l0 type dummy
+ ip netns exec ns0 ip link show l0
8: l0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 1e:4a:72:e3:e3:8f brd ff:ff:ff:ff:ff:ff
+ ip link add l0 type dummy
+ ip link show l0
10: l0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether f2:fc:fe:2b:7d:a6 brd ff:ff:ff:ff:ff:ff
+ ip link set l0 netns ns0
RTNETLINK answers: File exists
The problem is that do_setlink() passes its `char *ifname` argument,
that it gets from a caller, to __dev_change_net_namespace() as is (as
`const char *pat`), but semantics of ifname and pat can be different.
For example, __rtnl_newlink() does this:
net/core/rtnetlink.c
3270 char ifname[IFNAMSIZ];
...
3286 if (tb[IFLA_IFNAME])
3287 nla_strscpy(ifname, tb[IFLA_IFNAME], IFNAMSIZ);
3288 else
3289 ifname[0] = '\0';
...
3364 if (dev) {
...
3394 return do_setlink(skb, dev, ifm, extack, tb, ifname, status);
3395 }
, i.e. do_setlink() gets ifname pointer that is always valid no matter
if user specified IFLA_IFNAME or not and then do_setlink() passes this
ifname pointer as is to __dev_change_net_namespace() as pat argument.
But the pat (pattern) in __dev_change_net_namespace() is used as:
net/core/dev.c
11198 err = -EEXIST;
11199 if (__dev_get_by_name(net, dev->name)) {
11200 /* We get here if we can't use the current device name */
11201 if (!pat)
11202 goto out;
11203 err = dev_get_valid_name(net, dev, pat);
11204 if (err < 0)
11205 goto out;
11206 }
As the result the `goto out` path on line 11202 is neven taken and
instead of returning EEXIST defined on line 11198,
__dev_change_net_namespace() returns an error from dev_get_valid_name()
and this, in turn, will be EINVAL for ifname[0] = '\0' set earlier.
Fixes: d8a5ec6727 ("[NET]: netlink support for moving devices between network namespaces.")
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43fed4d48d ]
When adapter init fails, the blocked freelist bitmap is already freed
up and should not be touched. So, move the bitmap zeroing closer to
where it was successfully allocated. Also handle adapter init failure
unwind path immediately and avoid setting up RDMA memory windows.
Fixes: 5b377d114f ("cxgb4: Add debugfs facility to inject FL starvation")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6457378fe7 ]
A group of security researchers brought to our attention
the weakness of hash function used in fnhe_hashfun().
Lets use siphash instead of Jenkins Hash, to considerably
reduce security risks.
Also remove the inline keyword, this really is distracting.
Fixes: d546c62154 ("ipv4: harden fnhe_hashfun()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Keyu Man <kman001@ucr.edu>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4785305c05 ]
A group of security researchers brought to our attention
the weakness of hash function used in rt6_exception_hash()
Lets use siphash instead of Jenkins Hash, to considerably
reduce security risks.
Following patch deals with IPv4.
Fixes: 35732d01fe ("ipv6: introduce a hash table to store dst cache")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Keyu Man <kman001@ucr.edu>
Cc: Wei Wang <weiwan@google.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Acked-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd9b50adc6 ]
While running kselftests, Hangbin observed that sch_ets.sh often crashes,
and splats like the following one are seen in the output of 'dmesg':
BUG: kernel NULL pointer dereference, address: 0000000000000000
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 159f12067 P4D 159f12067 PUD 159f13067 PMD 0
Oops: 0000 [#1] SMP NOPTI
CPU: 2 PID: 921 Comm: tc Not tainted 5.14.0-rc6+ #458
Hardware name: Red Hat KVM, BIOS 1.11.1-4.module+el8.1.0+4066+0f1aadab 04/01/2014
RIP: 0010:__list_del_entry_valid+0x2d/0x50
Code: 48 8b 57 08 48 b9 00 01 00 00 00 00 ad de 48 39 c8 0f 84 ac 6e 5b 00 48 b9 22 01 00 00 00 00 ad de 48 39 ca 0f 84 cf 6e 5b 00 <48> 8b 32 48 39 fe 0f 85 af 6e 5b 00 48 8b 50 08 48 39 f2 0f 85 94
RSP: 0018:ffffb2da005c3890 EFLAGS: 00010217
RAX: 0000000000000000 RBX: ffff9073ba23f800 RCX: dead000000000122
RDX: 0000000000000000 RSI: 0000000000000008 RDI: ffff9073ba23fbc8
RBP: ffff9073ba23f890 R08: 0000000000000001 R09: 0000000000000001
R10: 0000000000000001 R11: 0000000000000001 R12: dead000000000100
R13: ffff9073ba23fb00 R14: 0000000000000002 R15: 0000000000000002
FS: 00007f93e5564e40(0000) GS:ffff9073bba00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 000000014ad34000 CR4: 0000000000350ee0
Call Trace:
ets_qdisc_reset+0x6e/0x100 [sch_ets]
qdisc_reset+0x49/0x1d0
tbf_reset+0x15/0x60 [sch_tbf]
qdisc_reset+0x49/0x1d0
dev_reset_queue.constprop.42+0x2f/0x90
dev_deactivate_many+0x1d3/0x3d0
dev_deactivate+0x56/0x90
qdisc_graft+0x47e/0x5a0
tc_get_qdisc+0x1db/0x3e0
rtnetlink_rcv_msg+0x164/0x4c0
netlink_rcv_skb+0x50/0x100
netlink_unicast+0x1a5/0x280
netlink_sendmsg+0x242/0x480
sock_sendmsg+0x5b/0x60
____sys_sendmsg+0x1f2/0x260
___sys_sendmsg+0x7c/0xc0
__sys_sendmsg+0x57/0xa0
do_syscall_64+0x3a/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f93e44b8338
Code: 89 02 48 c7 c0 ff ff ff ff eb b5 0f 1f 80 00 00 00 00 f3 0f 1e fa 48 8d 05 25 43 2c 00 8b 00 85 c0 75 17 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 58 c3 0f 1f 80 00 00 00 00 41 54 41 89 d4 55
RSP: 002b:00007ffc0db737a8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 0000000061255c06 RCX: 00007f93e44b8338
RDX: 0000000000000000 RSI: 00007ffc0db73810 RDI: 0000000000000003
RBP: 0000000000000000 R08: 0000000000000001 R09: 0000000000000000
R10: 000000000000000b R11: 0000000000000246 R12: 0000000000000001
R13: 0000000000687880 R14: 0000000000000000 R15: 0000000000000000
Modules linked in: sch_ets sch_tbf dummy rfkill iTCO_wdt iTCO_vendor_support intel_rapl_msr intel_rapl_common joydev i2c_i801 pcspkr i2c_smbus lpc_ich virtio_balloon ip_tables xfs libcrc32c crct10dif_pclmul crc32_pclmul crc32c_intel ahci libahci ghash_clmulni_intel libata serio_raw virtio_blk virtio_console virtio_net net_failover failover sunrpc dm_mirror dm_region_hash dm_log dm_mod
CR2: 0000000000000000
When the change() function decreases the value of 'nstrict', we must take
into account that packets might be already enqueued on a class that flips
from 'strict' to 'quantum': otherwise that class will not be added to the
bandwidth-sharing list. Then, a call to ets_qdisc_reset() will attempt to
do list_del(&alist) with 'alist' filled with zero, hence the NULL pointer
dereference.
For classes flipping from 'strict' to 'quantum', initialize an empty list
and eventually add it to the bandwidth-sharing list, if there are packets
already enqueued. In this way, the kernel will:
a) prevent crashing as described above.
b) avoid retaining the backlog packets (for an arbitrarily long time) in
case no packet is enqueued after a change from 'strict' to 'quantum'.
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Fixes: dcc68b4d80 ("net: sch_ets: Add a new Qdisc")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 359f4cdd7d ]
According to Armada XP datasheet bit at 0 position is corresponding for
TxInProg indication.
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Signed-off-by: Maxim Kiselev <bigunclemax@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ed74b03eb ]
A successful 'xge_mdio_config()' call should be balanced by a corresponding
'xge_mdio_remove()' call in the error handling path of the probe, as
already done in the remove function.
Update the error handling path accordingly.
Fixes: ea8ab16ab2 ("drivers: net: xgene-v2: Add MDIO support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44a13a5d99 ]
We should decode the latency and the max_latency before directly compare.
The latency should be presented as lat_enc = scale x value:
lat_enc_d = (lat_enc & 0x0x3ff) x (1U << (5*((max_ltr_enc & 0x1c00)
>> 10)))
Fixes: cf8fb73c23 ("e1000e: add support for LTR on I217/I218")
Suggested-by: Yee Li <seven.yi.lee@gmail.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b79959510 ]
After unplug thunderbolt dock with i225, pciehp interrupt is triggered,
remove call will read/write mmio address which is already disconnected,
then cause page fault and make system hang.
Check PCI state to remove device safely.
Trace:
BUG: unable to handle page fault for address: 000000000000b604
Oops: 0000 [#1] SMP NOPTI
RIP: 0010:igc_rd32+0x1c/0x90 [igc]
Call Trace:
igc_ptp_suspend+0x6c/0xa0 [igc]
igc_ptp_stop+0x12/0x50 [igc]
igc_remove+0x7f/0x1c0 [igc]
pci_device_remove+0x3e/0xb0
__device_release_driver+0x181/0x240
Fixes: 13b5b7fd6a ("igc: Add support for Tx/Rx rings")
Fixes: b03c49cde6 ("igc: Save PTP time before a reset")
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ffc9c3ebb4 ]
- restore the behavior in enable_net_traffic() to avoid regressions - Jakub
Kicinski;
- hurried up and removed redundant assignment in pegasus_open() before yet
another checker complains;
Fixes: 8a160e2e9a ("net: usb: pegasus: Check the return value of get_geristers() and friends;")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Petko Manolov <petko.manolov@konsulko.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8f89fa277 ]
The devlink dev info command reports version information about the
device and firmware running on the board. This includes the "board.id"
field which is supposed to represent an identifier of the board design.
The ice driver uses the Product Board Assembly identifier for this.
In some cases, the PBA is not present in the NVM. If this happens,
devlink dev info will fail with an error. Instead, modify the
ice_info_pba function to just exit without filling in the context
buffer. This will cause the board.id field to be skipped. Log a dev_dbg
message in case someone wants to confirm why board.id is not showing up
for them.
Fixes: e961b679fb ("ice: add board identifier info to devlink .info_get")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20210819223451.245613-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbe71c6199 ]
kmalloc_array() is called to allocate memory for tx->descp. If it fails,
the function __sdma_txclean() is called:
__sdma_txclean(dd, tx);
However, in the function __sdma_txclean(), tx-descp is dereferenced if
tx->num_desc is not zero:
sdma_unmap_desc(dd, &tx->descp[0]);
To fix this possible null-pointer dereference, assign the return value of
kmalloc_array() to a local variable descp, and then assign it to tx->descp
if it is not NULL. Otherwise, go to enomem.
Fixes: 7724105686 ("IB/hfi1: add driver files")
Link: https://lore.kernel.org/r/20210806133029.194964-1-islituo@gmail.com
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Tuo Li <islituo@gmail.com>
Tested-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 02c6dcd543 upstream.
We found a hang, the steps to reproduce are as follows:
1. blocking device via scsi_device_set_state()
2. dd if=/dev/sda of=/mnt/t.log bs=1M count=10
3. echo none > /sys/block/sda/queue/scheduler
4. echo "running" >/sys/block/sda/device/state
Step 3 and 4 should complete after step 4, but they hang.
CPU#0 CPU#1 CPU#2
--------------- ---------------- ----------------
Step 1: blocking device
Step 2: dd xxxx
^^^^^^ get request
q_usage_counter++
Step 3: switching scheculer
elv_iosched_store
elevator_switch
blk_mq_freeze_queue
blk_freeze_queue
> blk_freeze_queue_start
^^^^^^ mq_freeze_depth++
> blk_mq_run_hw_queues
^^^^^^ can't run queue when dev blocked
> blk_mq_freeze_queue_wait
^^^^^^ Hang here!!!
wait q_usage_counter==0
Step 4: running device
store_state_field
scsi_rescan_device
scsi_attach_vpd
scsi_vpd_inquiry
__scsi_execute
blk_get_request
blk_mq_alloc_request
blk_queue_enter
^^^^^^ Hang here!!!
wait mq_freeze_depth==0
blk_mq_run_hw_queues
^^^^^^ dispatch IO, q_usage_counter will reduce to zero
blk_mq_unfreeze_queue
^^^^^ mq_freeze_depth--
To fix this, we need to run queue before rescanning device when the device
state changes to SDEV_RUNNING.
Link: https://lore.kernel.org/r/20210824025921.3277629-1-lijinlin3@huawei.com
Fixes: f0f82e2476 ("scsi: core: Fix capacity set to zero after offlinining device")
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Li Jinlin <lijinlin3@huawei.com>
Signed-off-by: Qiu Laibin <qiulaibin@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a1e25c0a0 upstream.
During a USB cable disconnect, or soft disconnect scenario, a pending
SETUP transaction may not be completed, leading to the following
error:
dwc3 a600000.dwc3: timed out waiting for SETUP phase
If this occurs, then the entire pullup disable routine is skipped and
proper cleanup and halting of the controller does not complete.
Instead of returning an error (which is ignored from the UDC
perspective), allow the pullup disable routine to continue, which
will also handle disabling of EP0/1. This will end any active
transfers as well. Ensure to clear any delayed_status also, as the
timeout could happen within the STATUS stage.
Fixes: bb01473648 ("usb: dwc3: gadget: don't clear RUN/STOP when it's invalid to do so")
Cc: <stable@vger.kernel.org>
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/20210825042855.7977-1-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51f1954ad8 upstream.
We can't depend on the TRB's HWO bit to determine if the TRB ring is
"full". A TRB is only available when the driver had processed it, not
when the controller consumed and relinquished the TRB's ownership to the
driver. Otherwise, the driver may overwrite unprocessed TRBs. This can
happen when many transfer events accumulate and the system is slow to
process them and/or when there are too many small requests.
If a request is in the started_list, that means there is one or more
unprocessed TRBs remained. Check this instead of the TRB's HWO bit
whether the TRB ring is full.
Fixes: c4233573f6 ("usb: dwc3: gadget: prepare TRBs on update transfers too")
Cc: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/e91e975affb0d0d02770686afc3a5b9eb84409f6.1629335416.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c82cacd2f1 upstream.
The recent attempt to handle an unknown ROM state in the commit
d143825baf ("usb: renesas-xhci: Fix handling of unknown ROM state")
resulted in a regression and reverted later by the commit 44cf53602f
("Revert "usb: renesas-xhci: Fix handling of unknown ROM state"").
The problem of the former fix was that it treated the failure of
firmware loading as a fatal error. Since the firmware files aren't
included in the standard linux-firmware tree, most users don't have
them, hence they got the non-working system after that. The revert
fixed the regression, but also it didn't make the firmware loading
triggered even on the devices that do need it. So we need still a fix
for them.
This is another attempt to handle the unknown ROM state. Like the
previous fix, this also tries to load the firmware when ROM shows
unknown state. In this patch, however, the failure of a firmware
loading (such as a missing firmware file) isn't handled as a fatal
error any longer when ROM has been already detected, but it falls back
to the ROM mode like before. The error is returned only when no ROM
is detected and the firmware loading failed.
Along with it, for simplifying the code flow, the detection and the
check of ROM is factored out from renesas_fw_check_running() and done
in the caller side, renesas_xhci_check_request_fw(). It avoids the
redundant ROM checks.
The patch was tested on Lenovo Thinkpad T14 gen (BIOS 1.34). Also it
was confirmed that no regression is seen on another Thinkpad T14
machine that has worked without the patch, too.
Fixes: 44cf53602f ("Revert "usb: renesas-xhci: Fix handling of unknown ROM state"")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://bugzilla.opensuse.org/show_bug.cgi?id=1189207
Link: https://lore.kernel.org/r/20210826124127.14789-1-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32bc8f8373 upstream.
schedule_delayed_work does not push back the work if it was already
scheduled before, so amdgpu_device_delay_enable_gfx_off ran ~100 ms
after the first time GFXOFF was disabled and re-enabled, even if GFXOFF
was disabled and re-enabled again during those 100 ms.
This resulted in frame drops / stutter with the upcoming mutter 41
release on Navi 14, due to constantly enabling GFXOFF in the HW and
disabling it again (for getting the GPU clock counter).
To fix this, call cancel_delayed_work_sync when the disable count
transitions from 0 to 1, and only schedule the delayed work on the
reverse transition, not if the disable count was already 0. This makes
sure the delayed work doesn't run at unexpected times, and allows it to
be lock-free.
v2:
* Use cancel_delayed_work_sync & mutex_trylock instead of
mod_delayed_work.
v3:
* Make amdgpu_device_delay_enable_gfx_off lock-free (Christian König)
v4:
* Fix race condition between amdgpu_gfx_off_ctrl incrementing
adev->gfx.gfx_off_req_count and amdgpu_device_delay_enable_gfx_off
checking for it to be 0 (Evan Quan)
Cc: stable@vger.kernel.org
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com> # v3
Acked-by: Christian König <christian.koenig@amd.com> # v3
Signed-off-by: Michel Dänzer <mdaenzer@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e9655763b upstream.
This reverts commit f216562731.
[BUG]
It's no longer possible to create compressed inline extent after commit
f216562731 ("btrfs: compression: don't try to compress if we don't
have enough pages").
[CAUSE]
For compression code, there are several possible reasons we have a range
that needs to be compressed while it's no more than one page.
- Compressed inline write
The data is always smaller than one sector and the test lacks the
condition to properly recognize a non-inline extent.
- Compressed subpage write
For the incoming subpage compressed write support, we require page
alignment of the delalloc range.
And for 64K page size, we can compress just one page into smaller
sectors.
For those reasons, the requirement for the data to be more than one page
is not correct, and is already causing regression for compressed inline
data writeback. The idea of skipping one page to avoid wasting CPU time
could be revisited in the future.
[FIX]
Fix it by reverting the offending commit.
Reported-by: Zygo Blaxell <ce3g8jdj@umail.furryterror.org>
Link: https://lore.kernel.org/linux-btrfs/afa2742.c084f5d6.17b6b08dffc@tnonline.net
Fixes: f216562731 ("btrfs: compression: don't try to compress if we don't have enough pages")
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 379eb01c21 upstream.
The value of FP registers in the core dump file comes from the
thread.fstate. However, kernel saves the FP registers to the thread.fstate
only before scheduling out the process. If no process switch happens
during the exception handling process, kernel will not have a chance to
save the latest value of FP registers to thread.fstate. It will cause the
value of FP registers in the core dump file may be incorrect. To solve this
problem, this patch force lets kernel save the FP register into the
thread.fstate if the target task_struct equals the current.
Signed-off-by: Vincent Chen <vincent.chen@sifive.com>
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Fixes: b8c8a9590e ("RISC-V: Add FP register ptrace support for gdb.")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2f9fa1f3b upstream.
The ceph_cap_flush structures are usually dynamically allocated, but
the ceph_cap_snap has an embedded one.
When force umounting, the client will try to remove all the session
caps. During this, it will free them, but that should not be done
with the ones embedded in a capsnap.
Fix this by adding a new boolean that indicates that the cap flush is
embedded in a capsnap, and skip freeing it if that's set.
At the same time, switch to using list_del_init() when detaching the
i_list and g_list heads. It's possible for a forced umount to remove
these objects but then handle_cap_flushsnap_ack() races in and does the
list_del_init() again, corrupting memory.
Cc: stable@vger.kernel.org
URL: https://tracker.ceph.com/issues/52283
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 48c812e032 ]
The ocelot driver makes use of regmap, wrapping it with driver specific
operations that are thin wrappers around the core regmap APIs. These are
exported with EXPORT_SYMBOL, dropping the _GPL from the core regmap
exports which is frowned upon. Add _GPL suffixes to at least the APIs that
are doing register I/O.
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 580c610429 ]
One error path can result in release_dentry_name_snapshot() being called
before "name" was initialized by take_dentry_name_snapshot().
Fix by moving the release_dentry_name_snapshot() to immediately after the
only use.
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4608fdfc07 ]
Michal Kubecek reports that conntrack gc is responsible for frequent
wakeups (every 125ms) on idle systems.
On busy systems, timed out entries are evicted during lookup.
The gc worker is only needed to remove entries after system becomes idle
after a busy period.
To resolve this, always scan the entire table.
If the scan is taking too long, reschedule so other work_structs can run
and resume from next bucket.
After a completed scan, wait for 2 minutes before the next cycle.
Heuristics for faster re-schedule are removed.
GC_SCAN_INTERVAL could be exposed as a sysctl in the future to allow
tuning this as-needed or even turn the gc worker off.
Reported-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf79167fd8 ]
Enabling CONFIG_STACKDEPOT results in the following build error.
arc-elf-ld: lib/stackdepot.o: in function `filter_irq_stacks':
stackdepot.c:(.text+0x456): undefined reference to `__irqentry_text_start'
arc-elf-ld: stackdepot.c:(.text+0x456): undefined reference to `__irqentry_text_start'
arc-elf-ld: stackdepot.c:(.text+0x476): undefined reference to `__irqentry_text_end'
arc-elf-ld: stackdepot.c:(.text+0x476): undefined reference to `__irqentry_text_end'
arc-elf-ld: stackdepot.c:(.text+0x484): undefined reference to `__softirqentry_text_start'
arc-elf-ld: stackdepot.c:(.text+0x484): undefined reference to `__softirqentry_text_start'
arc-elf-ld: stackdepot.c:(.text+0x48c): undefined reference to `__softirqentry_text_end'
arc-elf-ld: stackdepot.c:(.text+0x48c): undefined reference to `__softirqentry_text_end'
Other architectures address this problem by adding IRQENTRY_TEXT and
SOFTIRQENTRY_TEXT to the text segment, so do the same here.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31428c7874 ]
When the component level pin control functions were added they for some
no longer obvious reason handled adding prefixing of widget names. This
meant that when the lack of prefix handling in the DAPM level pin
operations was fixed by ae4fc53224 (ASoC: dapm: use component
prefix when checking widget names) the one device using the component
level API ended up with the prefix being applied twice, causing all
lookups to fail.
Fix this by removing the redundant prefixing from the component code,
which has the nice side effect of also making that code much simpler.
Reported-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Tested-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210726194123.54585-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b910eaaaa4 upstream.
Jiri Olsa reported a bug ([1]) in kernel where cgroup local
storage pointer may be NULL in bpf_get_local_storage() helper.
There are two issues uncovered by this bug:
(1). kprobe or tracepoint prog incorrectly sets cgroup local storage
before prog run,
(2). due to change from preempt_disable to migrate_disable,
preemption is possible and percpu storage might be overwritten
by other tasks.
This issue (1) is fixed in [2]. This patch tried to address issue (2).
The following shows how things can go wrong:
task 1: bpf_cgroup_storage_set() for percpu local storage
preemption happens
task 2: bpf_cgroup_storage_set() for percpu local storage
preemption happens
task 1: run bpf program
task 1 will effectively use the percpu local storage setting by task 2
which will be either NULL or incorrect ones.
Instead of just one common local storage per cpu, this patch fixed
the issue by permitting 8 local storages per cpu and each local
storage is identified by a task_struct pointer. This way, we
allow at most 8 nested preemption between bpf_cgroup_storage_set()
and bpf_cgroup_storage_unset(). The percpu local storage slot
is released (calling bpf_cgroup_storage_unset()) by the same task
after bpf program finished running.
bpf_test_run() is also fixed to use the new bpf_cgroup_storage_set()
interface.
The patch is tested on top of [2] with reproducer in [1].
Without this patch, kernel will emit error in 2-3 minutes.
With this patch, after one hour, still no error.
[1] https://lore.kernel.org/bpf/CAKH8qBuXCfUz=w8L+Fj74OaUpbosO29niYwTki7e3Ag044_aww@mail.gmail.com/T
[2] https://lore.kernel.org/bpf/20210309185028.3763817-1-yhs@fb.com
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Roman Gushchin <guro@fb.com>
Link: https://lore.kernel.org/bpf/20210323055146.3334476-1-yhs@fb.com
Cc: <stable@vger.kernel.org> # 5.10.x
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5b029a32cf upstream.
Commit 457f44363a ("bpf: Implement BPF ring buffer and verifier support
for it") extended check_map_func_compatibility() by enforcing map -> helper
function match, but not helper -> map type match.
Due to this all of the bpf_ringbuf_*() helper functions could be used with
a wrong map type such as array or hash map, leading to invalid access due
to type confusion.
Also, both BPF_FUNC_ringbuf_{submit,discard} have ARG_PTR_TO_ALLOC_MEM as
argument and not a BPF map. Therefore, their check_map_func_compatibility()
presence is incorrect since it's only for map type checking.
Fixes: 457f44363a ("bpf: Implement BPF ring buffer and verifier support for it")
Reported-by: Ryota Shiga (Flatt Security)
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e78c597c3 upstream.
This check was incomplete, did not consider size is 0:
if (len != ALIGN(size, 4) + hdrlen)
goto err;
if size from qrtr_hdr is 0, the result of ALIGN(size, 4)
will be 0, In case of len == hdrlen and size == 0
in header this check won't fail and
if (cb->type == QRTR_TYPE_NEW_SERVER) {
/* Remote node endpoint can bridge other distant nodes */
const struct qrtr_ctrl_pkt *pkt = data + hdrlen;
qrtr_node_assign(node, le32_to_cpu(pkt->server.node));
}
will also read out of bound from data, which is hdrlen allocated block.
Fixes: 194ccc8829 ("net: qrtr: Support decoding incoming v2 packets")
Fixes: ad9d24c942 ("net: qrtr: fix OOB Read in qrtr_endpoint_post")
Signed-off-by: Xiaolong Huang <butterflyhuangxx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ upstream commit 21f965221e ]
If an SQPOLL based ring is newly created and an application issues an
io_uring_enter(2) system call on it, then we can return a spurious
-EOWNERDEAD error. This happens because there's nothing to submit, and
if the caller doesn't specify any other action, the initial error
assignment of -EOWNERDEAD never gets overwritten. This causes us to
return it directly, even if it isn't valid.
Move the error assignment into the actual failure case instead.
Cc: stable@vger.kernel.org
Fixes: d9d05217cb ("io_uring: stop SQPOLL submit on creator's death")
Reported-by: Sherlock Holo sherlockya@gmail.com
Link: https://github.com/axboe/liburing/issues/413
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ upstream commit a30f895ad3 ]
We currently check for ret != 0 to indicate error, but '1' is a valid
return and just indicates that the allocation succeeded with a wrap.
Correct the check to be for < 0, like it was before the xarray
conversion.
Cc: stable@vger.kernel.org
Fixes: 61cf93700f ("io_uring: Convert personality_idr to XArray")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fdd92b64d1 ]
We've had CONFIG_MANDATORY_FILE_LOCKING since 2015 and a lot of distros
have disabled it. Warn the stragglers that still use "-o mand" that
we'll be dropping support for that mount option.
Cc: stable@vger.kernel.org
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f56ce412a5 ]
We've noticed occasional OOM killing when memory.low settings are in
effect for cgroups. This is unexpected and undesirable as memory.low is
supposed to express non-OOMing memory priorities between cgroups.
The reason for this is proportional memory.low reclaim. When cgroups
are below their memory.low threshold, reclaim passes them over in the
first round, and then retries if it couldn't find pages anywhere else.
But when cgroups are slightly above their memory.low setting, page scan
force is scaled down and diminished in proportion to the overage, to the
point where it can cause reclaim to fail as well - only in that case we
currently don't retry, and instead trigger OOM.
To fix this, hook proportional reclaim into the same retry logic we have
in place for when cgroups are skipped entirely. This way if reclaim
fails and some cgroups were scanned with diminished pressure, we'll try
another full-force cycle before giving up and OOMing.
[akpm@linux-foundation.org: coding-style fixes]
Link: https://lkml.kernel.org/r/20210817180506.220056-1-hannes@cmpxchg.org
Fixes: 9783aa9917 ("mm, memcg: proportional memory.{low,min} reclaim")
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reported-by: Leon Yang <lnyng@fb.com>
Reviewed-by: Rik van Riel <riel@surriel.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Roman Gushchin <guro@fb.com>
Acked-by: Chris Down <chris@chrisdown.name>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: <stable@vger.kernel.org> [5.4+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65ca89c2b1 ]
The commit 2e6b836312 ("ASoC: intel: atom: Fix reference to PCM
buffer address") changed the reference of PCM buffer address to
substream->runtime->dma_addr as the buffer address may change
dynamically. However, I forgot that the dma_addr field is still not
set up for the CONTINUOUS buffer type (that this driver uses) yet in
5.14 and earlier kernels, and it resulted in garbage I/O. The problem
will be fixed in 5.15, but we need to address it quickly for now.
The fix is to deduce the address again from the DMA pointer with
virt_to_phys(), but from the right one, substream->runtime->dma_area.
Fixes: 2e6b836312 ("ASoC: intel: atom: Fix reference to PCM buffer address")
Reported-and-tested-by: Hans de Goede <hdegoede@redhat.com>
Cc: <stable@vger.kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/2048c6aa-2187-46bd-6772-36a4fb3c5aeb@redhat.com
Link: https://lore.kernel.org/r/20210819152945.8510-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a671f77ee ]
The struct pci_dev uses reference counting but zPCI assumed erroneously
that the last reference would always be the local reference after
calling pci_stop_and_remove_bus_device(). This is usually the case but
not how reference counting works and thus inherently fragile.
In fact one case where this causes a NULL pointer dereference when on an
SRIOV device the function 0 was hot unplugged before another function of
the same multi-function device. In this case the second function's
pdev->sriov->dev reference keeps the struct pci_dev of function 0 alive
even after the unplug. This bug was previously hidden by the fact that
we were leaking the struct pci_dev which in turn means that it always
outlived the struct zpci_dev. This was fixed in commit 0b13525c20
("s390/pci: fix leak of PCI device structure") exposing the broken
behavior.
Fix this by accounting for the long living reference a struct pci_dev
has to its underlying struct zpci_dev via the zbus->function[] array and
only release that in pcibios_release_device() ensuring that the struct
pci_dev is not left with a dangling reference. This is a minimal fix in
the future it would probably better to use fine grained reference
counting for struct zpci_dev.
Fixes: 05bc1be6db ("s390/pci: create zPCI bus")
Cc: stable@vger.kernel.org
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57a1681095 ]
The function tpci200_register called by tpci200_install and
tpci200_unregister called by tpci200_uninstall are in pair. However,
tpci200_unregister has some cleanup operations not in the
tpci200_register. So the error handling code of tpci200_pci_probe has
many different double free issues.
Fix this problem by moving those cleanup operations out of
tpci200_unregister, into tpci200_pci_remove and reverting
the previous commit 9272e5d002 ("ipack/carriers/tpci200:
Fix a double free in tpci200_pci_probe").
Fixes: 9272e5d002 ("ipack/carriers/tpci200: Fix a double free in tpci200_pci_probe")
Cc: stable@vger.kernel.org
Reported-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Link: https://lore.kernel.org/r/20210810100323.3938492-1-mudongliangabcd@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a263c1ff6a ]
In some usecases transaction ids are dynamically allocated inside
the controller driver after sending the messages which have generic
acknowledge responses. So check for this before refcounting pm_runtime.
Without this we would end up imbalancing runtime pm count by
doing pm_runtime_put() in both slim_do_transfer() and slim_msg_response()
for a single pm_runtime_get() in slim_do_transfer()
Fixes: d3062a2109 ("slimbus: messaging: add slim_alloc/free_txn_tid()")
Cc: <stable@vger.kernel.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210809082428.11236-3-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9711759a87 ]
As GDSCs are registered and found to be already enabled gdsc_init()
ensures that 1) the kernel state matches the hardware state, and 2)
votable GDSCs are properly enabled from this master as well.
But as the (optional) supply regulator is enabled deep into
gdsc_toggle_logic(), which is only executed for votable GDSCs, the
kernel's state of the regulator might not match the hardware. The
regulator might be automatically turned off if no other users are
present or the next call to gdsc_disable() would cause an unbalanced
regulator_disable().
Given that the votable case deals with an already enabled GDSC, most of
gdsc_enable() and gdsc_toggle_logic() can be skipped. Reduce it to just
clearing the SW_COLLAPSE_MASK and enabling hardware control to simply
call regulator_enable() in both cases.
The enablement of hardware control seems to be an independent property
from the GDSC being enabled, so this is moved outside that conditional
segment.
Lastly, as the propagation of ALWAYS_ON to GENPD_FLAG_ALWAYS_ON needs to
happen regardless of the initial state this is grouped together with the
other sc->pd updates at the end of the function.
Cc: stable@vger.kernel.org
Fixes: 37416e5549 ("clk: qcom: gdsc: Handle GDSC regulator supplies")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210721224056.3035016-1-bjorn.andersson@linaro.org
[sboyd@kernel.org: Rephrase commit text]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 25f8203b4b ]
When a Data CRC interrupt is received, the driver disables the DMA, then
sends the stop/abort command and then waits for Data Transfer Over.
However, sometimes, when a data CRC error is received in the middle of a
multi-block write transfer, the Data Transfer Over interrupt is never
received, and the driver hangs and never completes the request.
The driver sets the BMOD.SWR bit (SDMMC_IDMAC_SWRESET) when stopping the
DMA, but according to the manual CMD.STOP_ABORT_CMD should be programmed
"before assertion of SWR". Do these operations in the recommended
order. With this change the Data Transfer Over is always received
correctly in my tests.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210630102232.16011-1-vincent.whitchurch@axis.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa05bdb89b ]
This reverts commit 9ea3e52c5b.
Cited commit added a check to make sure 'action' is not NULL, but
'action' is already dereferenced before the check, when calling
flow_offload_has_one_action().
Therefore, the check does not make any sense and results in a smatch
warning:
include/net/flow_offload.h:322 flow_action_mixed_hw_stats_check() warn:
variable dereferenced before check 'action' (see line 319)
Fix by reverting this commit.
Cc: gushengxian <gushengxian@yulong.com>
Fixes: 9ea3e52c5b ("flow_offload: action should not be NULL when it is referenced")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://lore.kernel.org/r/20210819105842.1315705-1-idosch@idosch.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8da80c9d50 ]
Make changes to MAC address dependent on the response of PF.
Disallow changes to HW MAC address and MAC filter from untrusted
VF, thanks to that ping is not lost if VF tries to change MAC.
Add a new field in iavf_mac_filter, to indicate whether there
was response from PF for given filter. Based on this field pass
or discard the filter.
If untrusted VF tried to change it's address, it's not changed.
Still filter was changed, because of that ping couldn't go through.
Fixes: c5c922b3e0 ("iavf: fix MAC address setting for VFs when filter is rejected")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Gurucharan G <Gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a222be597e ]
Without this patch, ATR does not work. Receive/transmit uses queue
selection based on SW DCB hashing method.
If traffic classes are not configured for PF, then use
netdev_pick_tx function for selecting queue for packet transmission.
Instead of calling i40e_swdcb_skb_tx_hash, call netdev_pick_tx,
which ensures that packet is transmitted/received from CPU that is
running the application.
Reproduction steps:
1. Load i40e driver
2. Map each MSI interrupt of i40e port for each CPU
3. Disable ntuple, enable ATR i.e.:
ethtool -K $interface ntuple off
ethtool --set-priv-flags $interface flow-director-atr
4. Run application that is generating traffic and is bound to a
single CPU, i.e.:
taskset -c 9 netperf -H 1.1.1.1 -t TCP_RR -l 10
5. Observe behavior:
Application's traffic should be restricted to the CPU provided in
taskset.
Fixes: 89ec1f0886 ("i40e: Fix queue-to-TC mapping on Tx")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a876a33d2a ]
The register of USB_BP2_EN is 16 bits, so we should use
ocp_write_word(), not ocp_write_byte().
Fixes: 9370f2d05a ("support request_firmware for RTL8153")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8798d36411 ]
This fixes improper iotlb invalidation in intel_pasid_tear_down_entry().
When a PASID was used as nested mode, released and reused, the following
error message will appear:
[ 180.187556] Unexpected page request in Privilege Mode
[ 180.187565] Unexpected page request in Privilege Mode
[ 180.279933] Unexpected page request in Privilege Mode
[ 180.279937] Unexpected page request in Privilege Mode
Per chapter 6.5.3.3 of VT-d spec 3.3, when tear down a pasid entry, the
software should use Domain selective IOTLB flush if the PGTT of the pasid
entry is SL only or Nested, while for the pasid entries whose PGTT is FL
only or PT using PASID-based IOTLB flush is enough.
Fixes: 2cd1311a26 ("iommu/vt-d: Add set domain DOMAIN_ATTR_NESTING attr")
Signed-off-by: Kumar Sanjay K <sanjay.k.kumar@intel.com>
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Tested-by: Yi Sun <yi.y.sun@intel.com>
Link: https://lore.kernel.org/r/20210817042425.1784279-1-yi.l.liu@intel.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210817124321.1517985-3-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 01634047bf ]
fq qdisc requires tstamp to be cleared in the forwarding path. Now ovs
doesn't clear skb->tstamp. We encountered a problem with linux
version 5.4.56 and ovs version 2.14.1, and packets failed to
dequeue from qdisc when fq qdisc was attached to ovs port.
Fixes: fb420d5d91 ("tcp/fq: move back to CLOCK_MONOTONIC")
Signed-off-by: kaixi.fan <fankaixi.li@bytedance.com>
Signed-off-by: xiexiaohui <xiexiaohui.xxh@bytedance.com>
Reviewed-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7bd0cef5da ]
When registering mdiobus children, if we get an -EPROBE_DEFER, we shouldn't
ignore it and continue registering the rest of the mdiobus children. This
would permanently prevent the deferring child mdiobus from working instead
of reattempting it in the future. So, if a child mdiobus needs to be
reattempted in the future, defer the entire mdio-mux initialization.
This fixes the issue where PHYs sitting under the mdio-mux aren't
initialized correctly if the PHY's interrupt controller is not yet ready
when the mdio-mux is being probed. Additional context in the link below.
Fixes: 0ca2997d14 ("netdev/of/phy: Add MDIO bus multiplexer support.")
Link: https://lore.kernel.org/lkml/CAGETcx95kHrv8wA-O+-JtfH7H9biJEGJtijuPVN0V5dUKUAB3A@mail.gmail.com/#t
Signed-off-by: Saravana Kannan <saravanak@google.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Marc Zyngier <maz@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86b9bbd332 ]
When adding support for using the skb->hash value as the flow hash in CAKE,
I accidentally introduced a logic error that broke the host-only isolation
modes of CAKE (srchost and dsthost keywords). Specifically, the flow_hash
variable should stay initialised to 0 in cake_hash() in pure host-based
hashing mode. Add a check for this before using the skb->hash value as
flow_hash.
Fixes: b0c19ed608 ("sch_cake: Take advantage of skb->hash where appropriate")
Reported-by: Pete Heist <pete@heistp.net>
Tested-by: Pete Heist <pete@heistp.net>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dbcf24d153 ]
Commit a02e8964ea ("virtio-net: ethtool configurable LRO")
maps LRO to virtio guest offloading features and allows the
administrator to enable and disable those features via ethtool.
This leads to several issues:
- For a device that doesn't support control guest offloads, the "LRO"
can't be disabled triggering WARN in dev_disable_lro() when turning
off LRO or when enabling forwarding bridging etc.
- For a device that supports control guest offloads, the guest
offloads are disabled in cases of bridging, forwarding etc slowing
down the traffic.
Fix this by using NETIF_F_GRO_HW instead. Though the spec does not
guarantee packets to be re-segmented as the original ones,
we can add that to the spec, possibly with a flag for devices to
differentiate between GRO and LRO.
Further, we never advertised LRO historically before a02e8964ea
("virtio-net: ethtool configurable LRO") and so bridged/forwarded
configs effectively always relied on virtio receive offloads behaving
like GRO - thus even if this breaks any configs it is at least not
a regression.
Fixes: a02e8964ea ("virtio-net: ethtool configurable LRO")
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reported-by: Ivan <ivan@prestigetransportation.com>
Tested-by: Ivan <ivan@prestigetransportation.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97c2c69e19 ]
The number of queues implemented by many virtio backends is limited,
especially some machines have a large number of CPUs. In this case, it
is often impossible to allocate a separate queue for
XDP_TX/XDP_REDIRECT, then xdp cannot be loaded to work, even xdp does
not use the XDP_TX/XDP_REDIRECT.
This patch allows XDP_TX/XDP_REDIRECT to run by reuse the existing SQ
with __netif_tx_lock() hold when there are not enough queues.
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Reviewed-by: Dust Li <dust.li@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09e856d54b ]
To fix the "reverse-NAT" for replies.
When a packet is sent over a VRF, the POST_ROUTING hooks are called
twice: Once from the VRF interface, and once from the "actual"
interface the packet will be sent from:
1) First SNAT: l3mdev_l3_out() -> vrf_l3_out() -> .. -> vrf_output_direct()
This causes the POST_ROUTING hooks to run.
2) Second SNAT: 'ip_output()' calls POST_ROUTING hooks again.
Similarly for replies, first ip_rcv() calls PRE_ROUTING hooks, and
second vrf_l3_rcv() calls them again.
As an example, consider the following SNAT rule:
> iptables -t nat -A POSTROUTING -p udp -m udp --dport 53 -j SNAT --to-source 2.2.2.2 -o vrf_1
In this case sending over a VRF will create 2 conntrack entries.
The first is from the VRF interface, which performs the IP SNAT.
The second will run the SNAT, but since the "expected reply" will remain
the same, conntrack randomizes the source port of the packet:
e..g With a socket bound to 1.1.1.1:10000, sending to 3.3.3.3:53, the conntrack
rules are:
udp 17 29 src=2.2.2.2 dst=3.3.3.3 sport=10000 dport=53 packets=1 bytes=68 [UNREPLIED] src=3.3.3.3 dst=2.2.2.2 sport=53 dport=61033 packets=0 bytes=0 mark=0 use=1
udp 17 29 src=1.1.1.1 dst=3.3.3.3 sport=10000 dport=53 packets=1 bytes=68 [UNREPLIED] src=3.3.3.3 dst=2.2.2.2 sport=53 dport=10000 packets=0 bytes=0 mark=0 use=1
i.e. First SNAT IP from 1.1.1.1 --> 2.2.2.2, and second the src port is
SNAT-ed from 10000 --> 61033.
But when a reply is sent (3.3.3.3:53 -> 2.2.2.2:61033) only the later
conntrack entry is matched:
udp 17 29 src=2.2.2.2 dst=3.3.3.3 sport=10000 dport=53 packets=1 bytes=68 src=3.3.3.3 dst=2.2.2.2 sport=53 dport=61033 packets=1 bytes=49 mark=0 use=1
udp 17 28 src=1.1.1.1 dst=3.3.3.3 sport=10000 dport=53 packets=1 bytes=68 [UNREPLIED] src=3.3.3.3 dst=2.2.2.2 sport=53 dport=10000 packets=0 bytes=0 mark=0 use=1
And a "port 61033 unreachable" ICMP packet is sent back.
The issue is that when PRE_ROUTING hooks are called from vrf_l3_rcv(),
the skb already has a conntrack flow attached to it, which means
nf_conntrack_in() will not resolve the flow again.
This means only the dest port is "reverse-NATed" (61033 -> 10000) but
the dest IP remains 2.2.2.2, and since the socket is bound to 1.1.1.1 it's
not received.
This can be verified by logging the 4-tuple of the packet in '__udp4_lib_rcv()'.
The fix is then to reset the flow when skb is received on a VRF, to let
conntrack resolve the flow again (which now will hit the earlier flow).
To reproduce: (Without the fix "Got pkt_to_nat_port" will not be printed by
running 'bash ./repro'):
$ cat run_in_A1.py
import logging
logging.getLogger("scapy.runtime").setLevel(logging.ERROR)
from scapy.all import *
import argparse
def get_packet_to_send(udp_dst_port, msg_name):
return Ether(src='11:22:33:44:55:66', dst=iface_mac)/ \
IP(src='3.3.3.3', dst='2.2.2.2')/ \
UDP(sport=53, dport=udp_dst_port)/ \
Raw(f'{msg_name}\x0012345678901234567890')
parser = argparse.ArgumentParser()
parser.add_argument('-iface_mac', dest="iface_mac", type=str, required=True,
help="From run_in_A3.py")
parser.add_argument('-socket_port', dest="socket_port", type=str,
required=True, help="From run_in_A3.py")
parser.add_argument('-v1_mac', dest="v1_mac", type=str, required=True,
help="From script")
args, _ = parser.parse_known_args()
iface_mac = args.iface_mac
socket_port = int(args.socket_port)
v1_mac = args.v1_mac
print(f'Source port before NAT: {socket_port}')
while True:
pkts = sniff(iface='_v0', store=True, count=1, timeout=10)
if 0 == len(pkts):
print('Something failed, rerun the script :(', flush=True)
break
pkt = pkts[0]
if not pkt.haslayer('UDP'):
continue
pkt_sport = pkt.getlayer('UDP').sport
print(f'Source port after NAT: {pkt_sport}', flush=True)
pkt_to_send = get_packet_to_send(pkt_sport, 'pkt_to_nat_port')
sendp(pkt_to_send, '_v0', verbose=False) # Will not be received
pkt_to_send = get_packet_to_send(socket_port, 'pkt_to_socket_port')
sendp(pkt_to_send, '_v0', verbose=False)
break
$ cat run_in_A2.py
import socket
import netifaces
print(f"{netifaces.ifaddresses('e00000')[netifaces.AF_LINK][0]['addr']}",
flush=True)
s = socket.socket(socket.AF_INET, socket.SOCK_DGRAM)
s.setsockopt(socket.SOL_SOCKET, socket.SO_BINDTODEVICE,
str('vrf_1' + '\0').encode('utf-8'))
s.connect(('3.3.3.3', 53))
print(f'{s. getsockname()[1]}', flush=True)
s.settimeout(5)
while True:
try:
# Periodically send in order to keep the conntrack entry alive.
s.send(b'a'*40)
resp = s.recvfrom(1024)
msg_name = resp[0].decode('utf-8').split('\0')[0]
print(f"Got {msg_name}", flush=True)
except Exception as e:
pass
$ cat repro.sh
ip netns del A1 2> /dev/null
ip netns del A2 2> /dev/null
ip netns add A1
ip netns add A2
ip -n A1 link add _v0 type veth peer name _v1 netns A2
ip -n A1 link set _v0 up
ip -n A2 link add e00000 type bond
ip -n A2 link add lo0 type dummy
ip -n A2 link add vrf_1 type vrf table 10001
ip -n A2 link set vrf_1 up
ip -n A2 link set e00000 master vrf_1
ip -n A2 addr add 1.1.1.1/24 dev e00000
ip -n A2 link set e00000 up
ip -n A2 link set _v1 master e00000
ip -n A2 link set _v1 up
ip -n A2 link set lo0 up
ip -n A2 addr add 2.2.2.2/32 dev lo0
ip -n A2 neigh add 1.1.1.10 lladdr 77:77:77:77:77:77 dev e00000
ip -n A2 route add 3.3.3.3/32 via 1.1.1.10 dev e00000 table 10001
ip netns exec A2 iptables -t nat -A POSTROUTING -p udp -m udp --dport 53 -j \
SNAT --to-source 2.2.2.2 -o vrf_1
sleep 5
ip netns exec A2 python3 run_in_A2.py > x &
XPID=$!
sleep 5
IFACE_MAC=`sed -n 1p x`
SOCKET_PORT=`sed -n 2p x`
V1_MAC=`ip -n A2 link show _v1 | sed -n 2p | awk '{print $2'}`
ip netns exec A1 python3 run_in_A1.py -iface_mac ${IFACE_MAC} -socket_port \
${SOCKET_PORT} -v1_mac ${SOCKET_PORT}
sleep 5
kill -9 $XPID
wait $XPID 2> /dev/null
ip netns del A1
ip netns del A2
tail x -n 2
rm x
set +x
Fixes: 73e20b761a ("net: vrf: Add support for PREROUTING rules on vrf device")
Signed-off-by: Lahav Schlesinger <lschlesinger@drivenets.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20210815120002.2787653-1-lschlesinger@drivenets.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 828affc27e ]
Each completion ring entry has a valid bit to indicate that the entry
contains a valid completion event. The driver's main poll loop
__bnxt_poll_work() has the proper dma_rmb() to make sure the valid
bit of the next entry has been checked before proceeding further.
But when we call bnxt_rx_pkt() to process the RX event, the RX
completion event consists of two completion entries and only the
first entry has been checked to be valid. We need the same barrier
after checking the next completion entry. Add missing dma_rmb()
barriers in bnxt_rx_pkt() and other similar locations.
Fixes: 67a95e2022 ("bnxt_en: Need memory barrier when processing the completion ring.")
Reported-by: Lance Richardson <lance.richardson@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Reviewed-by: Lance Richardson <lance.richardson@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55c8fca1da ]
During the swap dependency on PCH_GBE to selection PTP_1588_CLOCK_PCH
incidentally dropped the implicit dependency on the PCI. Restore it.
Fixes: 18d359ceb0 ("pch_gbe, ptp_pch: Fix the dependency direction between these drivers")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19d1532a18 ]
Syzbot reported slab-out-of bounds write in decode_data().
The problem was in missing validation checks.
Syzbot's reproducer generated malicious input, which caused
decode_data() to be called a lot in sixpack_decode(). Since
rx_count_cooked is only 400 bytes and noone reported before,
that 400 bytes is not enough, let's just check if input is malicious
and complain about buffer overrun.
Fail log:
==================================================================
BUG: KASAN: slab-out-of-bounds in drivers/net/hamradio/6pack.c:843
Write of size 1 at addr ffff888087c5544e by task kworker/u4:0/7
CPU: 0 PID: 7 Comm: kworker/u4:0 Not tainted 5.6.0-rc3-syzkaller #0
...
Workqueue: events_unbound flush_to_ldisc
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x197/0x210 lib/dump_stack.c:118
print_address_description.constprop.0.cold+0xd4/0x30b mm/kasan/report.c:374
__kasan_report.cold+0x1b/0x32 mm/kasan/report.c:506
kasan_report+0x12/0x20 mm/kasan/common.c:641
__asan_report_store1_noabort+0x17/0x20 mm/kasan/generic_report.c:137
decode_data.part.0+0x23b/0x270 drivers/net/hamradio/6pack.c:843
decode_data drivers/net/hamradio/6pack.c:965 [inline]
sixpack_decode drivers/net/hamradio/6pack.c:968 [inline]
Reported-and-tested-by: syzbot+fc8cd9a673d4577fb2e4@syzkaller.appspotmail.com
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8d8c5d80f ]
skbs are freed on error and not put on the ring. We may, however,
be in a situation where we're freeing the last skb of a batch,
and there is a doorbell ring pending because of xmit_more() being
true earlier. Make sure we ring the door bell in such situations.
Since errors are rare don't pay attention to xmit_more() and just
always flush the pending frames.
The busy case should be safe to be left alone because it can
only happen if start_xmit races with completions and they
both enable the queue. In that case the kick can't be pending.
Noticed while reading the code.
Fixes: 4d172f21ce ("bnxt_en: Implement xmit_more.")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 01cca6b933 ]
napi schedules DIM, napi has to be disabled first,
then DIM canceled.
Noticed while reading the code.
Fixes: 0bc0b97fca ("bnxt_en: cleanup DIM work on device shutdown")
Fixes: 6a8788f256 ("bnxt_en: add support for software dynamic interrupt moderation")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c603136c9 ]
We can't take the tx lock from the napi poll routine, because
netpoll can poll napi at any moment, including with the tx lock
already held.
The tx lock is protecting against two paths - the disable
path, and (as Michael points out) the NETDEV_TX_BUSY case
which may occur if NAPI completions race with start_xmit
and both decide to re-enable the queue.
For the disable/ifdown path use synchronize_net() to make sure
closing the device does not race we restarting the queues.
Annotate accesses to dev_state against data races.
For the NAPI cleanup vs start_xmit path - appropriate barriers
are already in place in the main spot where Tx queue is stopped
but we need to do the same careful dance in the TX_BUSY case.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45c709f8c7 ]
"access skb fields ok" verifier test fails on s390 with the "verifier
bug. zext_dst is set, but no reg is defined" message. The first insns
of the test prog are ...
0: 61 01 00 00 00 00 00 00 ldxw %r0,[%r1+0]
8: 35 00 00 01 00 00 00 00 jge %r0,0,1
10: 61 01 00 08 00 00 00 00 ldxw %r0,[%r1+8]
... and the 3rd one is dead (this does not look intentional to me, but
this is a separate topic).
sanitize_dead_code() converts dead insns into "ja -1", but keeps
zext_dst. When opt_subreg_zext_lo32_rnd_hi32() tries to parse such
an insn, it sees this discrepancy and bails. This problem can be seen
only with JITs whose bpf_jit_needs_zext() returns true.
Fix by clearning dead insns' zext_dst.
The commits that contributed to this problem are:
1. 5aa5bd14c5 ("bpf: add initial suite for selftests"), which
introduced the test with the dead code.
2. 5327ed3d44 ("bpf: verifier: mark verified-insn with
sub-register zext flag"), which introduced the zext_dst flag.
3. 83a2881903 ("bpf: Account for BPF_FETCH in
insn_has_def32()"), which introduced the sanity check.
4. 9183671af6 ("bpf: Fix leakage under speculation on
mispredicted branches"), which bisect points to.
It's best to fix this on stable branches that contain the second one,
since that's the point where the inconsistency was introduced.
Fixes: 5327ed3d44 ("bpf: verifier: mark verified-insn with sub-register zext flag")
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210812151811.184086-2-iii@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71dcadba34 ]
The orginal setting is not correct, fix it to follow hardware data sheet.
If keep this error setting, mt8173/mt8183 display ok
but mt8192 display abnormal.
Fixes: 0664d1392c ("drm/mediatek: Add AAL engine basic function")
Signed-off-by: Yongqiang Niu <yongqiang.niu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08dbd56602 ]
The current code treats an empty iotlb provdied in set_map() as a
special case and destroy the memory region object. This must not be done
since the virtqueue objects reference this MR. Doing so will cause the
driver unload to emit errors and log timeouts caused by the firmware
complaining on busy resources.
This patch treats an empty iotlb as any other change of mapping. In this
case, mlx5_vdpa_create_mr() will fail and the entire set_map() call to
fail.
This issue has not been encountered before but was seen to occur in a
non-official version of qemu. Since qemu is a userspace program, the
driver must protect against such case.
Fixes: 94abbccdf2 ("vdpa/mlx5: Add shared memory registration code")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20210811053713.66658-1-elic@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06a089ef64 ]
We have changed the return type for sysc_check_active_timer() from -EBUSY
to -ENXIO, but the gpt12 system timer fix still checks for -EBUSY. We are
also not returning on other errors like we did earlier as noted by
Pavel Machek <pavel@denx.de>.
Commit 3ff340e24c ("bus: ti-sysc: Fix gpt12 system timer issue with
reserved status") should have been updated for commit 65fb736761
("bus: ti-sysc: suppress err msg for timers used as clockevent/source").
Let's fix the issue by checking for -ENXIO and returning on any other
errors as suggested by Pavel Machek <pavel@denx.de>.
Fixes: 3ff340e24c ("bus: ti-sysc: Fix gpt12 system timer issue with reserved status")
Depends-on: 65fb736761 ("bus: ti-sysc: suppress err msg for timers used as clockevent/source")
Reported-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Pavel Machek (CIP) <pavel@denx.de>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86aab09a48 ]
GCC complains about empty macros in an 'if' statement, so convert
them to 'do {} while (0)' macros.
Fixes these build warnings:
net/dccp/output.c: In function 'dccp_xmit_packet':
../net/dccp/output.c:283:71: warning: suggest braces around empty body in an 'if' statement [-Wempty-body]
283 | dccp_pr_debug("transmit_skb() returned err=%d\n", err);
net/dccp/ackvec.c: In function 'dccp_ackvec_update_old':
../net/dccp/ackvec.c:163:80: warning: suggest braces around empty body in an 'else' statement [-Wempty-body]
163 | (unsigned long long)seqno, state);
Fixes: dc841e30ea ("dccp: Extend CCID packet dequeueing interface")
Fixes: 3802408644 ("dccp ccid-2: Update code for the Ack Vector input/registration routine")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: dccp@vger.kernel.org
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 484f2b7c61 ]
The 1.2 GHz variant of the Armada 3720 SOC is unstable with DVFS: when
the SOC boots, the WTMI firmware sets clocks and AVS values that work
correctly with 1.2 GHz CPU frequency, but random crashes occur once
cpufreq driver starts scaling.
We do not know currently what is the reason:
- it may be that the voltage value for L0 for 1.2 GHz variant provided
by the vendor in the OTP is simply incorrect when scaling is used,
- it may be that some delay is needed somewhere,
- it may be something else.
The most sane solution now seems to be to simply forbid the cpufreq
driver on 1.2 GHz variant.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: 92ce45fb87 ("cpufreq: Add DVFS support for Armada 37xx")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5aa95d8834 ]
If probe_device is failing, iommu_group is not initialized because
iommu_group_add_device is not reached, so freeing it will result
in NULL pointer access.
iommu_bus_init
->bus_iommu_probe
->probe_iommu_group in for each:/* return -22 in fail case */
->iommu_probe_device
->__iommu_probe_device /* return -22 here.*/
-> ops->probe_device /* return -22 here.*/
-> iommu_group_get_for_dev
-> ops->device_group
-> iommu_group_add_device //good case
->remove_iommu_group //in fail case, it will remove group
->iommu_release_device
->iommu_group_remove_device // here we don't have group
In my case ops->probe_device (mtk_iommu_probe_device from
mtk_iommu_v1.c) is due to failing fwspec->ops mismatch.
Fixes: d72e31c937 ("iommu: IOMMU Groups")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://lore.kernel.org/r/20210731074737.4573-1-linux@fw-web.de
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cca342d98b ]
A different wait queue was used when removing ctrl_wait than when adding
it. This effectively made the remove operation without locking compared
to other operations on the wait queue ctrl_wait was part of. This caused
issues like below where dead000000000100 is LIST_POISON1 and
dead000000000200 is LIST_POISON2.
list_add corruption. next->prev should be prev (ffffffc1b0a33a08), \
but was dead000000000200. (next=ffffffc03ac77de0).
------------[ cut here ]------------
CPU: 3 PID: 2138 Comm: bluetoothd Tainted: G O 4.4.238+ #9
...
---[ end trace 0adc2158f0646eac ]---
Call trace:
[<ffffffc000443f78>] __list_add+0x38/0xb0
[<ffffffc0000f0d04>] add_wait_queue+0x4c/0x68
[<ffffffc00020eecc>] __pollwait+0xec/0x100
[<ffffffc000d1556c>] bt_sock_poll+0x74/0x200
[<ffffffc000bdb8a8>] sock_poll+0x110/0x128
[<ffffffc000210378>] do_sys_poll+0x220/0x480
[<ffffffc0002106f0>] SyS_poll+0x80/0x138
[<ffffffc00008510c>] __sys_trace_return+0x0/0x4
Unable to handle kernel paging request at virtual address dead000000000100
...
CPU: 4 PID: 5387 Comm: kworker/u15:3 Tainted: G W O 4.4.238+ #9
...
Call trace:
[<ffffffc0000f079c>] __wake_up_common+0x7c/0xa8
[<ffffffc0000f0818>] __wake_up+0x50/0x70
[<ffffffc000be11b0>] sock_def_wakeup+0x58/0x60
[<ffffffc000de5e10>] l2cap_sock_teardown_cb+0x200/0x224
[<ffffffc000d3f2ac>] l2cap_chan_del+0xa4/0x298
[<ffffffc000d45ea0>] l2cap_conn_del+0x118/0x198
[<ffffffc000d45f8c>] l2cap_disconn_cfm+0x6c/0x78
[<ffffffc000d29934>] hci_event_packet+0x564/0x2e30
[<ffffffc000d19b0c>] hci_rx_work+0x10c/0x360
[<ffffffc0000c2218>] process_one_work+0x268/0x460
[<ffffffc0000c2678>] worker_thread+0x268/0x480
[<ffffffc0000c94e0>] kthread+0x118/0x128
[<ffffffc000085070>] ret_from_fork+0x10/0x20
---[ end trace 0adc2158f0646ead ]---
Signed-off-by: Ole Bjørn Midtbø <omidtbo@cisco.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4152b297d ]
[Why]
HPD disable and enable sequences are not mutually exclusive
on Linux. For HPDs that spans over 1s (i.e. HPD low = 1s),
part of the disable sequence (specifically, a request to SMU
to lower refclk) could come right before the call to PHY
enable, causing DMUB to access an unresponsive PHY
and thus a hard hang on the system.
[How]
Disable 48mhz refclk off on native DP.
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06050a0f01 ]
Why:
In DCN2x, HW doesn't automatically divide MASTER_UPDATE_LOCK_DB_X
by the number of pipes ODM Combined.
How:
Set MASTER_UPDATE_LOCK_DB_X to the value that is adjusted by the
number of pipes ODM Combined.
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Bing Guo <bing.guo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b67d4d63e ]
Currently phy_device state could be left in inconsistent state shown
by following alert message[1]. This is because phy_read_status could
be called concurrently from lan78xx_delayedwork, phy_state_machine and
__ethtool_get_link. Fix this by making sure that phy_device state is
updated atomically.
[1] lan78xx 1-1.1.1:1.0 eth0: No phy led trigger registered for speed(-1)
Signed-off-by: Ivan T. Ivanov <iivanov@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a160e2e9a ]
Certain call sites of get_geristers() did not do proper error handling. This
could be a problem as get_geristers() typically return the data via pointer to a
buffer. If an error occurred the code is carelessly manipulating the wrong data.
Signed-off-by: Petko Manolov <petkan@nucleusys.com>
Reviewed-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1159e25c13 ]
A crash has been observed if rmmod is done while automatic debug
collection in progress. It is due to a race condition between
both of them.
To fix stop the sp_task during unload to avoid running qede_sp_task
even if they are schedule during removal process.
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f0f82e2476 ]
After adding physical volumes to a volume group through vgextend, the
kernel will rescan the partitions. This in turn will cause the device
capacity to be queried.
If the device status is set to offline through sysfs at this time, READ
CAPACITY command will return a result which the host byte is
DID_NO_CONNECT, and the capacity of the device will be set to zero in
read_capacity_error(). After setting device status back to running, the
capacity of the device will remain stuck at zero.
Fix this issue by rescanning device when the device state changes to
SDEV_RUNNING.
Link: https://lore.kernel.org/r/20210727034455.1494960-1-lijinlin3@huawei.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: lijinlin <lijinlin3@huawei.com>
Signed-off-by: Wu Bo <wubo40@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 70edd2e6f6 ]
Avoid printing a 'target allocation failed' error if the driver
target_alloc() callback function returns -ENXIO. This return value
indicates that the corresponding H:C:T:L entry is empty.
Removing this error reduces the scan time if the user issues SCAN_WILD_CARD
scan operation through sysfs parameter on a host with a lot of empty
H:C:T:L entries.
Avoiding the printk on -ENXIO matches the behavior of the other callback
functions during scanning.
Link: https://lore.kernel.org/r/20210726115402.1936-1-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eda97cb095 ]
If the router_xlate can not find the controller in the available DMA
devices then it should return with -EPORBE_DEFER in a same way as the
of_dma_request_slave_channel() does.
The issue can be reproduced if the event router is registered before the
DMA controller itself and a driver would request for a channel before the
controller is registered.
In of_dma_request_slave_channel():
1. of_dma_find_controller() would find the dma_router
2. ofdma->of_dma_xlate() would fail and returned NULL
3. -ENODEV is returned as error code
with this patch we would return in this case the correct -EPROBE_DEFER and
the client can try to request the channel later.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20210717190021.21897-1-peter.ujfalusi@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20a6b3fd8e ]
Based on the latest timing specifications for the TPS65218 from the data
sheet, http://www.ti.com/lit/ds/symlink/tps65218.pdf, document SLDS206
from November 2014, we must change the i2c bus speed to better fit within
the minimum high SCL time required for proper i2c transfer.
When running at 400khz, measurements show that SCL spends
0.8125 uS/1.666 uS high/low which violates the requirement for minimum
high period of SCL provided in datasheet Table 7.6 which is 1 uS.
Switching to 100khz gives us 5 uS/5 uS high/low which both fall above
the minimum given values for 100 khz, 4.0 uS/4.7 uS high/low.
Without this patch occasionally a voltage set operation from the kernel
will appear to have worked but the actual voltage reflected on the PMIC
will not have updated, causing problems especially with cpufreq that may
update to a higher OPP without actually raising the voltage on DCDC2,
leading to a hang.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7dd2dd4ff9 ]
When user calls dmaengine_terminate_sync, the driver will clean up any
remaining descriptors for all the pending or active transfers that had
previously been submitted. However, this might happen whilst the tasklet is
invoking the DMA callback for the last finished transfer, so by the time it
returns and takes over the channel's spinlock, the list of completed
descriptors it was traversing is no longer valid. This leads to a
read-after-free situation.
Fix it by signalling whether a user-triggered termination has happened by
means of a boolean variable.
Signed-off-by: Adrian Larumbe <adrian.martinezlarumbe@imgtec.com>
Link: https://lore.kernel.org/r/20210706234338.7696-3-adrian.martinezlarumbe@imgtec.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0863f1927 ]
When the user submits a control URB via usbfs, the user supplies the
bRequestType value and the kernel uses it to compute the pipe value.
However, do_proc_control() performs this computation incorrectly in
the case where the bRequestType direction bit is set to USB_DIR_IN and
the URB's transfer length is 0: The pipe's direction is also set to IN
but it should be OUT, which is the direction the actual transfer will
use regardless of bRequestType.
Commit 5cc59c418f ("USB: core: WARN if pipe direction != setup
packet direction") added a check to compare the direction bit in the
pipe value to a control URB's actual direction and to WARN if they are
different. This can be triggered by the incorrect computation
mentioned above, as found by syzbot.
This patch fixes the computation, thus avoiding the WARNing.
Reported-and-tested-by: syzbot+72af3105289dcb4c055b@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20210712185436.GB326369@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da6393cdd8 ]
Reported by syzkaller:
WARNING: CPU: 7 PID: 10526 at linux/arch/x86/kvm//x86.c:7621 x86_emulate_instruction+0x41b/0x510 [kvm]
RIP: 0010:x86_emulate_instruction+0x41b/0x510 [kvm]
Call Trace:
kvm_mmu_page_fault+0x126/0x8f0 [kvm]
vmx_handle_exit+0x11e/0x680 [kvm_intel]
vcpu_enter_guest+0xd95/0x1b40 [kvm]
kvm_arch_vcpu_ioctl_run+0x377/0x6a0 [kvm]
kvm_vcpu_ioctl+0x389/0x630 [kvm]
__x64_sys_ioctl+0x8e/0xd0
do_syscall_64+0x3c/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
Commit 4a1e10d5b5 ("KVM: x86: handle hardware breakpoints during emulation())
adds hardware breakpoints check before emulation the instruction and parts of
emulation context initialization, actually we don't have the EMULTYPE_NO_DECODE flag
here and the emulation context will not be reused. Commit c8848cee74 ("KVM: x86:
set ctxt->have_exception in x86_decode_insn()) triggers the warning because it
catches the stale emulation context has #UD, however, it is not during instruction
decoding which should result in EMULATION_FAILED. This patch fixes it by moving
the second part emulation context initialization into init_emulate_ctxt() and
before hardware breakpoints check. The ctxt->ud will be dropped by a follow-up
patch.
syzkaller source: https://syzkaller.appspot.com/x/repro.c?x=134683fdd00000
Reported-by: syzbot+71271244f206d17f6441@syzkaller.appspotmail.com
Fixes: 4a1e10d5b5 (KVM: x86: handle hardware breakpoints during emulation)
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Message-Id: <1622160097-37633-1-git-send-email-wanpengli@tencent.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4aa2691dcb ]
Move the instruction decode part out of x86_emulate_instruction() for it
to be used in other places. Also kvm_clear_exception_queue() is moved
inside the if-statement as it doesn't apply when KVM are coming back from
userspace.
Co-developed-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Wei Huang <wei.huang2@amd.com>
Message-Id: <20210126081831.570253-2-wei.huang2@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea354b6ddd ]
Syzbot discovered that the probe error handling doesn't clean up the
resources allocated in zr364xx_board_init(). There are several
related bugs in this code so I have re-written the error handling.
1) Introduce a new function zr364xx_board_uninit() which cleans up
the resources in zr364xx_board_init().
2) In zr364xx_board_init() if the call to zr364xx_start_readpipe()
fails then release the "cam->buffer.frame[i].lpvbits" memory
before returning. This way every function either allocates
everything successfully or it cleans up after itself.
3) Re-write the probe function so that each failure path goto frees
the most recent allocation. That way we don't free anything
before it has been allocated and we can also verify that
everything is freed.
4) Originally, in the probe function the "cam->v4l2_dev.release"
pointer was set to "zr364xx_release" near the start but I moved
that assignment to the end, after everything had succeeded. The
release function was never actually called during the probe cleanup
process, but with this change I wanted to make it clear that we
don't want to call zr364xx_release() until everything is
allocated successfully.
Next I re-wrote the zr364xx_release() function. Ideally this would
have been a simple matter of copy and pasting the cleanup code from
probe and adding an additional call to video_unregister_device(). But
there are a couple quirks to note.
1) The probe function does not call videobuf_mmap_free() and I don't
know where the videobuf_mmap is allocated. I left the code as-is to
avoid introducing a bug in code I don't understand.
2) The zr364xx_board_uninit() has a call to zr364xx_stop_readpipe()
which is a change from the original behavior with regards to
unloading the driver. Calling zr364xx_stop_readpipe() on a stopped
pipe is not a problem so this is safe and is potentially a bugfix.
Reported-by: syzbot+b4d54814b339b5c6bbd4@syzkaller.appspotmail.com
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af0321a5be ]
zr364xx_start_readpipe() can fail but callers do not care about that.
This can result in various negative consequences. The patch adds missed
error handling.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ca2848022c upstream.
Do not delete a key cache entry that is still being referenced by
pending frames in TXQs. This avoids reuse of the key cache entry while a
frame might still be transmitted using it.
To avoid having to do any additional operations during the main TX path
operations, track pending key cache entries in a new bitmap and check
whether any pending entries can be deleted before every new key
add/remove operation. Also clear any remaining entries when stopping the
interface.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201214172118.18100-6-jouni@codeaurora.org
Cc: Pali Rohár <pali@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56c5485c9e upstream.
It is possible for there to be pending frames in TXQs with a reference
to the key cache entry that is being deleted. If such a key cache entry
is cleared, those pending frame in TXQ might get transmitted without
proper encryption. It is safer to leave the previously used key into the
key cache in such cases. Instead, only clear the MAC address to prevent
RX processing from using this key cache entry.
This is needed in particularly in AP mode where the TXQs cannot be
flushed on station disconnection. This change alone may not be able to
address all cases where the key cache entry might get reused for other
purposes immediately (the key cache entry should be released for reuse
only once the TXQs do not have any remaining references to them), but
this makes it less likely to get unprotected frames and the more
complete changes may end up being significantly more complex.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201214172118.18100-2-jouni@codeaurora.org
Cc: Pali Rohár <pali@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the firmware doesn't setup the HSM rate (such as when booting
without an HDMI cable plugged in), its rate is 0 and thus any register
access results in a CPU stall, even though HSM is enabled.
Let's enforce a minimum rate at boot to avoid this issue.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Commit 9d44abbbb8 ("drm/vc4: Fall back to using an EDID probe in the
absence of a GPIO.") added some code to read the EDID through DDC in the
HDMI driver detect hook since the Pi3 had no HPD GPIO back then.
However, commit b1b8f45b31 ("ARM: dts: bcm2837: Add missing GPIOs of
Expander") changed that a couple of years later.
This causes an issue though since some TV (like the LG 55C8) when it
comes out of standy will deassert the HPD line, but the EDID will
remain readable.
It causes an issues nn platforms without an HPD GPIO, like the Pi4,
where the DDC probing will be our primary mean to detect a display, and
thus we will never detect the HPD pulse. This was fine before since the
pulse was small enough that we would never detect it, and we also didn't
have anything (like the scrambler) that needed to be set up in the
display.
However, now that we have both, the display during the HPD pulse will
clear its scrambler status, and since we won't detect the
disconnect/reconnect cycle we will never enable the scrambler back.
As our main reason for that DDC probing is gone, let's just remove it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The drm_helper_hpd_irq_event() documentation states that this function
is "useful for drivers which can't or don't track hotplug interrupts for
each connector." and that "Drivers which support hotplug interrupts for
each connector individually and which have a more fine-grained detect
logic should bypass this code and directly call
drm_kms_helper_hotplug_event()". This is thus what we ended-up doing.
However, what this actually means, and is further explained in the
drm_kms_helper_hotplug_event() documentation, is that
drm_kms_helper_hotplug_event() should be called by drivers that can
track the connection status change, and if it has changed we should call
that function.
This underlying expectation we failed to provide is that the caller of
drm_kms_helper_hotplug_event() should call drm_helper_probe_detect() to
probe the new status of the connector.
Since we didn't do it, it meant that even though we were sending the
notification to user-space and the DRM clients that something changed we
never probed or updated our internal connector status ourselves.
This went mostly unnoticed since the detect callback usually doesn't
have any side-effect. Also, if we were using the DRM fbdev emulation
(which is a DRM client), or any user-space application that can deal
with hotplug events, chances are they would react to the hotplug event
by probing the connector status eventually.
However, now that we have to enable the scrambler in detect() if it was
enabled it has a side effect, and an application such as Kodi or
modetest doesn't deal with hotplug events. This resulted with a black
screen when Kodi or modetest was running when a screen was disconnected
and then reconnected, or switched off and on.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The drm_helper_hpd_irq_event() function is iterating over all the
connectors when an hotplug event is detected.
During that iteration, it will call each connector detect function and
figure out if its status changed.
Finally, if any connector changed, it will notify the user-space and the
clients that something changed on the DRM device.
This is supposed to be used for drivers that don't have a hotplug
interrupt for individual connectors. However, drivers that can use an
interrupt for a single connector are left in the dust and can either
reimplement the logic used during the iteration for each connector or
use that helper and iterate over all connectors all the time.
Since both are suboptimal, let's create a helper that will only perform
the status detection on a single connector.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The PoE HAT cooling levels are not well suited for the PoE+ HAT - the
fan fails to come on until the temperature reaches the third trip point
(50C).
Give the rpi-poe-plus overlay a different set of cooling levels -
0 32 64 128 255, as suggested by @chris-kai-in.
See: https://github.com/raspberrypi/firmware/issues/1607
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
commit 9130c2d30c upstream.
On the CPU port, we can support both tagged and untagged VLANs at the
same time by doing any necessary untagging in software rather than
hardware. To enable that, keep the CPU port's Remove Tag flag cleared
and set the dsa_switch::untag_bridge_pvid flag.
Fixes: e66f840c08 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver")
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backport to 5.10: adjust context]
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af01754f9e upstream.
When a VLAN is deleted from a port, the flags in struct
switchdev_obj_port_vlan are always 0. ksz8_port_vlan_del() copies the
BRIDGE_VLAN_INFO_UNTAGGED flag to the port's Tag Removal flag, and
therefore always clears it.
In case there are multiple VLANs configured as untagged on this port -
which seems useless, but is allowed - deleting one of them changes the
remaining VLANs to be tagged.
It's only ever necessary to change this flag when a VLAN is added to
the port, so leave it unchanged in ksz8_port_vlan_del().
Fixes: e66f840c08 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver")
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backport to 5.10: adjust context]
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f4f58f88f upstream.
The switches supported by ksz8795 only have a per-port flag for Tag
Removal. This means it is not possible to support both tagged and
untagged VLANs on the same port. Reject attempts to add a VLAN that
requires the flag to be changed, unless there are no VLANs currently
configured.
VID 0 is excluded from this check since it is untagged regardless of
the state of the flag.
On the CPU port we could support tagged and untagged VLANs at the same
time. This will be enabled by a later patch.
Fixes: e66f840c08 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver")
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backport to 5.10:
- This configuration has to be detected and rejected in the
port_vlan_prepare operation
- ksz8795_port_vlan_add() has to check again to decide whether to
change the Tag Removal flag, so put the common condition in a
separate function
- Handle VID ranges]
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef3b02a1d7 upstream.
ksz8795 has never actually enabled PVID tag insertion, and it also
programmed the PVID incorrectly. To fix this:
* Allow tag insertion to be controlled per ingress port. On most
chips, set bit 2 in Global Control 19. On KSZ88x3 this control
flag doesn't exist.
* When adding a PVID:
- Set the appropriate register bits to enable tag insertion on
egress at every other port if this was the packet's ingress port.
- Mask *out* the VID from the default tag, before or-ing in the new
PVID.
* When removing a PVID:
- Clear the same control bits to disable tag insertion.
- Don't update the default tag. This wasn't doing anything useful.
Fixes: e66f840c08 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver")
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backport to 5.10:
- Drop the KSZ88x3 cases as those chips are not supported here
- Handle VID ranges in ksz8795_port_vlan_del()]
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ksz8795 and ksz9477 drivers differ in the way they count ports.
For ksz8795, ksz_device::port_cnt does not include the host port
whereas for ksz9477 it does. This inconsistency was fixed in Linux
5.11 by a series of changes, but remains in 5.10-stable.
When probing, the common code treats a port device node with an
address >= dev->port_cnt as a fatal error. As a minimal fix, change
it to compare again dev->mib_port_cnt. This is the length of the
dev->ports array that the port number will be used to index, and
always includes the host port.
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c7dfa40099 upstream.
If L1 disables VMLOAD/VMSAVE intercepts, and doesn't enable
Virtual VMLOAD/VMSAVE (currently not supported for the nested hypervisor),
then VMLOAD/VMSAVE must operate on the L1 physical memory, which is only
possible by making L0 intercept these instructions.
Failure to do so allowed the nested guest to run VMLOAD/VMSAVE unintercepted,
and thus read/write portions of the host physical memory.
Fixes: 89c8a4984f ("KVM: SVM: Enable Virtual VMLOAD VMSAVE feature")
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f923e0712 upstream.
* Invert the mask of bits that we pick from L2 in
nested_vmcb02_prepare_control
* Invert and explicitly use VIRQ related bits bitmask in svm_clear_vintr
This fixes a security issue that allowed a malicious L1 to run L2 with
AVIC enabled, which allowed the L2 to exploit the uninitialized and enabled
AVIC to read/write the host physical memory at some offsets.
Fixes: 3d6368ef58 ("KVM: SVM: Add VMRUN handler")
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 848378812e upstream.
A recent change in LLVM causes module_{c,d}tor sections to appear when
CONFIG_K{A,C}SAN are enabled, which results in orphan section warnings
because these are not handled anywhere:
ld.lld: warning: arch/x86/pci/built-in.a(legacy.o):(.text.asan.module_ctor) is being placed in '.text.asan.module_ctor'
ld.lld: warning: arch/x86/pci/built-in.a(legacy.o):(.text.asan.module_dtor) is being placed in '.text.asan.module_dtor'
ld.lld: warning: arch/x86/pci/built-in.a(legacy.o):(.text.tsan.module_ctor) is being placed in '.text.tsan.module_ctor'
Fangrui explains: "the function asan.module_ctor has the SHF_GNU_RETAIN
flag, so it is in a separate section even with -fno-function-sections
(default)".
Place them in the TEXT_TEXT section so that these technologies continue
to work with the newer compiler versions. All of the KASAN and KCSAN
KUnit tests continue to pass after this change.
Cc: stable@vger.kernel.org
Link: https://github.com/ClangBuiltLinux/linux/issues/1432
Link: 7b78956224
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Fangrui Song <maskray@google.com>
Acked-by: Marco Elver <elver@google.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210731023107.1932981-1-nathan@kernel.org
[nc: Resolve conflict due to lack of cf68fffb66]
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8434ffe71c upstream.
There is a race in ceph_put_snap_realm. The change to the nref and the
spinlock acquisition are not done atomically, so you could decrement
nref, and before you take the spinlock, the nref is incremented again.
At that point, you end up putting it on the empty list when it
shouldn't be there. Eventually __cleanup_empty_realms runs and frees
it when it's still in-use.
Fix this by protecting the 1->0 transition with atomic_dec_and_lock,
and just drop the spinlock if we can get the rwsem.
Because these objects can also undergo a 0->1 refcount transition, we
must protect that change as well with the spinlock. Increment locklessly
unless the value is at 0, in which case we take the spinlock, increment
and then take it off the empty list if it did the 0->1 transition.
With these changes, I'm removing the dout() messages from these
functions, as well as in __put_snap_realm. They've always been racy, and
it's better to not print values that may be misleading.
Cc: stable@vger.kernel.org
URL: https://tracker.ceph.com/issues/46419
Reported-by: Mark Nelson <mnelson@redhat.com>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Luis Henriques <lhenriques@suse.de>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df2c0cb7f8 upstream.
They both say that the snap_rwsem must be held for write, but I don't
see any real reason for it, and it's not currently always called that
way.
The lookup is just walking the rbtree, so holding it for read should be
fine there. The "get" is bumping the refcount and (possibly) removing
it from the empty list. I see no need to hold the snap_rwsem for write
for that.
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52dfd86aa5 upstream.
Opening a new file is done in 2 steps on regular filesystems:
1. Call the create inode-op on the parent-dir to create an inode
to hold the meta-data related to the file.
2. Call the open file-op to get a handle for the file.
vboxsf however does not really use disk-backed inodes because it
is based on passing through file-related system-calls through to
the hypervisor. So both steps translate to an open(2) call being
passed through to the hypervisor. With the handle returned by
the first call immediately being closed again.
Making 2 open calls for a single open(..., O_CREATE, ...) calls
has 2 problems:
a) It is not really efficient.
b) It actually breaks some apps.
An example of b) is doing a git clone inside a vboxsf mount.
When git clone tries to create a tempfile to store the pak
files which is downloading the following happens:
1. vboxsf_dir_mkfile() gets called with a mode of 0444 and succeeds.
2. vboxsf_file_open() gets called with file->f_flags containing
O_RDWR. When the host is a Linux machine this fails because doing
a open(..., O_RDWR) on a file which exists and has mode 0444 results
in an -EPERM error.
Other network-filesystems and fuse avoid the problem of needing to
pass 2 open() calls to the other side by using the atomic_open
directory-inode op.
This commit fixes git clone not working inside a vboxsf mount,
by adding support for the atomic_open directory-inode op.
As an added bonus this should also make opening new files faster.
The atomic_open implementation is modelled after the atomic_open
implementations from the 9p and fuse code.
Fixes: 0fd1695766 ("fs: Add VirtualBox guest shared folder (vboxsf) support")
Reported-by: Ludovic Pouzenc <bugreports@pouzenc.fr>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 02f840f907 upstream.
Factor out the code to create / release a struct vboxsf_handle into
2 new helper functions.
This is a preparation patch for adding atomic_open support.
Fixes: 0fd1695766 ("fs: Add VirtualBox guest shared folder (vboxsf) support")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 18712c1370 upstream.
Use vmx_need_pf_intercept() when determining if L0 wants to handle a #PF
in L2 or if the VM-Exit should be forwarded to L1. The current logic fails
to account for the case where #PF is intercepted to handle
guest.MAXPHYADDR < host.MAXPHYADDR and ends up reflecting all #PFs into
L1. At best, L1 will complain and inject the #PF back into L2. At
worst, L1 will eat the unexpected fault and cause L2 to hang on infinite
page faults.
Note, while the bug was technically introduced by the commit that added
support for the MAXPHYADDR madness, the shame is all on commit
a0c134347b ("KVM: VMX: introduce vmx_need_pf_intercept").
Fixes: 1dbf5d68af ("KVM: VMX: Add guest physical address check in EPT violation and misconfig")
Cc: stable@vger.kernel.org
Cc: Peter Shier <pshier@google.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Jim Mattson <jmattson@google.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210812045615.3167686-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b9cae027b upstream.
Use the secondary_exec_controls_get() accessor in vmx_has_waitpkg() to
effectively get the controls for the current VMCS, as opposed to using
vmx->secondary_exec_controls, which is the cached value of KVM's desired
controls for vmcs01 and truly not reflective of any particular VMCS.
While the waitpkg control is not dynamic, i.e. vmcs01 will always hold
the same waitpkg configuration as vmx->secondary_exec_controls, the same
does not hold true for vmcs02 if the L1 VMM hides the feature from L2.
If L1 hides the feature _and_ does not intercept MSR_IA32_UMWAIT_CONTROL,
L2 could incorrectly read/write L1's virtual MSR instead of taking a #GP.
Fixes: 6e3ba4abce ("KVM: vmx: Emulate MSR IA32_UMWAIT_CONTROL")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210810171952.2758100-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c32ac11da3 upstream.
On arm64, the stub only moves the kernel image around in memory if
needed, which is typically only for KASLR, given that relocatable
kernels (which is the default) can run from any 64k aligned address,
which is also the minimum alignment communicated to EFI via the PE/COFF
header.
Unfortunately, some loaders appear to ignore this header, and load the
kernel at some arbitrary offset in memory. We can deal with this, but
let's check for this condition anyway, so non-compliant code can be
spotted and fixed.
Cc: <stable@vger.kernel.org> # v5.10+
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77e89afc25 upstream.
Multi-MSI uses a single MSI descriptor and there is a single mask register
when the device supports per vector masking. To avoid reading back the mask
register the value is cached in the MSI descriptor and updates are done by
clearing and setting bits in the cache and writing it to the device.
But nothing protects msi_desc::masked and the mask register from being
modified concurrently on two different CPUs for two different Linux
interrupts which belong to the same multi-MSI descriptor.
Add a lock to struct device and protect any operation on the mask and the
mask register with it.
This makes the update of msi_desc::masked unconditional, but there is no
place which requires a modification of the hardware register without
updating the masked cache.
msi_mask_irq() is now an empty wrapper which will be cleaned up in follow
up changes.
The problem goes way back to the initial support of multi-MSI, but picking
the commit which introduced the mask cache is a valid cut off point
(2.6.30).
Fixes: f2440d9acb ("PCI MSI: Refactor interrupt masking code")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.726833414@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 361fd37397 upstream.
msi_mask_irq() takes a mask and a flags argument. The mask argument is used
to mask out bits from the cached mask and the flags argument to set bits.
Some places invoke it with a flags argument which sets bits which are not
used by the device, i.e. when the device supports up to 8 vectors a full
unmask in some places sets the mask to 0xFFFFFF00. While devices probably
do not care, it's still bad practice.
Fixes: 7ba1930db0 ("PCI MSI: Unmask MSI if setup failed")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.568173099@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b9255a7cb5 upstream.
Nothing enforces the posted writes to be visible when the function
returns. Flush them even if the flush might be redundant when the entry is
masked already as the unmask will flush as well. This is either setup or a
rare affinity change event so the extra flush is not the end of the world.
While this is more a theoretical issue especially the logic in the X86
specific msi_set_affinity() function relies on the assumption that the
update has reached the hardware when the function returns.
Again, as this never has been enforced the Fixes tag refers to a commit in:
git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
Fixes: f036d4ea5fa7 ("[PATCH] ia32 Message Signalled Interrupt support")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.515188147@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da181dc974 upstream.
The specification (PCIe r5.0, sec 6.1.4.5) states:
For MSI-X, a function is permitted to cache Address and Data values
from unmasked MSI-X Table entries. However, anytime software unmasks a
currently masked MSI-X Table entry either by clearing its Mask bit or
by clearing the Function Mask bit, the function must update any Address
or Data values that it cached from that entry. If software changes the
Address or Data value of an entry while the entry is unmasked, the
result is undefined.
The Linux kernel's MSI-X support never enforced that the entry is masked
before the entry is modified hence the Fixes tag refers to a commit in:
git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
Enforce the entry to be masked across the update.
There is no point in enforcing this to be handled at all possible call
sites as this is just pointless code duplication and the common update
function is the obvious place to enforce this.
Fixes: f036d4ea5fa7 ("[PATCH] ia32 Message Signalled Interrupt support")
Reported-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.462096385@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d5ec3d361 upstream.
When MSI-X is enabled the ordering of calls is:
msix_map_region();
msix_setup_entries();
pci_msi_setup_msi_irqs();
msix_program_entries();
This has a few interesting issues:
1) msix_setup_entries() allocates the MSI descriptors and initializes them
except for the msi_desc:masked member which is left zero initialized.
2) pci_msi_setup_msi_irqs() allocates the interrupt descriptors and sets
up the MSI interrupts which ends up in pci_write_msi_msg() unless the
interrupt chip provides its own irq_write_msi_msg() function.
3) msix_program_entries() does not do what the name suggests. It solely
updates the entries array (if not NULL) and initializes the masked
member for each MSI descriptor by reading the hardware state and then
masks the entry.
Obviously this has some issues:
1) The uninitialized masked member of msi_desc prevents the enforcement
of masking the entry in pci_write_msi_msg() depending on the cached
masked bit. Aside of that half initialized data is a NONO in general
2) msix_program_entries() only ensures that the actually allocated entries
are masked. This is wrong as experimentation with crash testing and
crash kernel kexec has shown.
This limited testing unearthed that when the production kernel had more
entries in use and unmasked when it crashed and the crash kernel
allocated a smaller amount of entries, then a full scan of all entries
found unmasked entries which were in use in the production kernel.
This is obviously a device or emulation issue as the device reset
should mask all MSI-X table entries, but obviously that's just part
of the paper specification.
Cure this by:
1) Masking all table entries in hardware
2) Initializing msi_desc::masked in msix_setup_entries()
3) Removing the mask dance in msix_program_entries()
4) Renaming msix_program_entries() to msix_update_entries() to
reflect the purpose of that function.
As the masking of unused entries has never been done the Fixes tag refers
to a commit in:
git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
Fixes: f036d4ea5fa7 ("[PATCH] ia32 Message Signalled Interrupt support")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.403833459@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 438553958b upstream.
The ordering of MSI-X enable in hardware is dysfunctional:
1) MSI-X is disabled in the control register
2) Various setup functions
3) pci_msi_setup_msi_irqs() is invoked which ends up accessing
the MSI-X table entries
4) MSI-X is enabled and masked in the control register with the
comment that enabling is required for some hardware to access
the MSI-X table
Step #4 obviously contradicts #3. The history of this is an issue with the
NIU hardware. When #4 was introduced the table access actually happened in
msix_program_entries() which was invoked after enabling and masking MSI-X.
This was changed in commit d71d6432e1 ("PCI/MSI: Kill redundant call of
irq_set_msi_desc() for MSI-X interrupts") which removed the table write
from msix_program_entries().
Interestingly enough nobody noticed and either NIU still works or it did
not get any testing with a kernel 3.19 or later.
Nevertheless this is inconsistent and there is no reason why MSI-X can't be
enabled and masked in the control register early on, i.e. move step #4
above to step #1. This preserves the NIU workaround and has no side effects
on other hardware.
Fixes: d71d6432e1 ("PCI/MSI: Kill redundant call of irq_set_msi_desc() for MSI-X interrupts")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Ashok Raj <ashok.raj@intel.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.344136412@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dbbc93576e upstream.
msi_domain_alloc_irqs() invokes irq_domain_activate_irq(), but
msi_domain_free_irqs() does not enforce deactivation before tearing down
the interrupts.
This happens when PCI/MSI interrupts are set up and never used before being
torn down again, e.g. in error handling pathes. The only place which cleans
that up is the error handling path in msi_domain_alloc_irqs().
Move the cleanup from msi_domain_alloc_irqs() into msi_domain_free_irqs()
to cure that.
Fixes: f3b0946d62 ("genirq/msi: Make sure PCI MSIs are activated early")
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210518033117.78104-1-cuibixuan@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 064855a690 upstream.
Creating a new sub monitoring group in the root /sys/fs/resctrl leads to
getting the "Unavailable" value for mbm_total_bytes and mbm_local_bytes
on the entire filesystem.
Steps to reproduce:
1. mount -t resctrl resctrl /sys/fs/resctrl/
2. cd /sys/fs/resctrl/
3. cat mon_data/mon_L3_00/mbm_total_bytes
23189832
4. Create sub monitor group:
mkdir mon_groups/test1
5. cat mon_data/mon_L3_00/mbm_total_bytes
Unavailable
When a new monitoring group is created, a new RMID is assigned to the
new group. But the RMID is not active yet. When the events are read on
the new RMID, it is expected to report the status as "Unavailable".
When the user reads the events on the default monitoring group with
multiple subgroups, the events on all subgroups are consolidated
together. Currently, if any of the RMID reads report as "Unavailable",
then everything will be reported as "Unavailable".
Fix the issue by discarding the "Unavailable" reads and reporting all
the successful RMID reads. This is not a problem on Intel systems as
Intel reports 0 on Inactive RMIDs.
Fixes: d89b737901 ("x86/intel_rdt/cqm: Add mon_data")
Reported-by: Paweł Szulik <pawel.szulik@intel.com>
Signed-off-by: Babu Moger <Babu.Moger@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: stable@vger.kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=213311
Link: https://lkml.kernel.org/r/162793309296.9224.15871659871696482080.stgit@bmoger-ubuntu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c0e37dc11 upstream.
The IO/APIC cannot handle interrupt affinity changes safely after startup
other than from an interrupt handler. The startup sequence in the generic
interrupt code violates that assumption.
Mark the irq chip with the new IRQCHIP_AFFINITY_PRE_STARTUP flag so that
the default interrupt setting happens before the interrupt is started up
for the first time.
Fixes: 1840475676 ("genirq: Expose default irq affinity mask (take 3)")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.832143400@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff363f480e upstream.
The X86 MSI mechanism cannot handle interrupt affinity changes safely after
startup other than from an interrupt handler, unless interrupt remapping is
enabled. The startup sequence in the generic interrupt code violates that
assumption.
Mark the irq chips with the new IRQCHIP_AFFINITY_PRE_STARTUP flag so that
the default interrupt setting happens before the interrupt is started up
for the first time.
While the interrupt remapping MSI chip does not require this, there is no
point in treating it differently as this might spare an interrupt to a CPU
which is not in the default affinity mask.
For the non-remapping case go to the direct write path when the interrupt
is not yet started similar to the not yet activated case.
Fixes: 1840475676 ("genirq: Expose default irq affinity mask (take 3)")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.886722080@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 826da77129 upstream.
X86 IO/APIC and MSI interrupts (when used without interrupts remapping)
require that the affinity setup on startup is done before the interrupt is
enabled for the first time as the non-remapped operation mode cannot safely
migrate enabled interrupts from arbitrary contexts. Provide a new irq chip
flag which allows affected hardware to request this.
This has to be opt-in because there have been reports in the past that some
interrupt chips cannot handle affinity setting before startup.
Fixes: 1840475676 ("genirq: Expose default irq affinity mask (take 3)")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.779791738@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3a26242375 ]
Commit 82046702e2 ("efi/libstub/arm64: Replace 'preferred' offset with
alignment check") simplified the way the stub moves the kernel image
around in memory before booting it, given that a relocatable image does
not need to be copied to a 2M aligned offset if it was loaded on a 64k
boundary by EFI.
Commit d32de9130f ("efi/arm64: libstub: Deal gracefully with
EFI_RNG_PROTOCOL failure") inadvertently defeated this logic by
overriding the value of efi_nokaslr if EFI_RNG_PROTOCOL is not
available, which was mistaken by the loader logic as an explicit request
on the part of the user to disable KASLR and any associated relocation
of an Image not loaded on a 2M boundary.
So let's reinstate this functionality, by capturing the value of
efi_nokaslr at function entry to choose the minimum alignment.
Fixes: d32de9130f ("efi/arm64: libstub: Deal gracefully with EFI_RNG_PROTOCOL failure")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5b94046efb ]
Distro versions of GRUB replace the usual LoadImage/StartImage calls
used to load the kernel image with some local code that fails to honor
the allocation requirements described in the PE/COFF header, as it
does not account for the image's BSS section at all: it fails to
allocate space for it, and fails to zero initialize it.
Since the EFI stub itself is allocated in the .init segment, which is
in the middle of the image, its BSS section is not impacted by this,
and the main consequence of this omission is that the BSS section may
overlap with memory regions that are already used by the firmware.
So let's warn about this condition, and force image reallocation to
occur in this case, which works around the problem.
Fixes: 82046702e2 ("efi/libstub/arm64: Replace 'preferred' offset with alignment check")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4152433c39 ]
The EFI stub random allocator used for kaslr on arm64 has a subtle
bug. In function get_entry_num_slots() which counts the number of
possible allocation "slots" for the image in a given chunk of free
EFI memory, "last_slot" can become negative if the chunk is smaller
than the requested allocation size.
The test "if (first_slot > last_slot)" doesn't catch it because
both first_slot and last_slot are unsigned.
I chose not to make them signed to avoid problems if this is ever
used on architectures where there are meaningful addresses with the
top bit set. Instead, fix it with an additional test against the
allocation size.
This can cause a boot failure in addition to a loss of randomisation
due to another bug in the arm64 stub fixed separately.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fixes: 2ddbfc81ea ("efi: stub: add implementation of efi_random_alloc()")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49b0b6ffe2 ]
There's a potential deadlock case when remove the vsock device or
process the RESET event:
vsock_for_each_connected_socket:
spin_lock_bh(&vsock_table_lock) ----------- (1)
...
virtio_vsock_reset_sock:
lock_sock(sk) --------------------- (2)
...
spin_unlock_bh(&vsock_table_lock)
lock_sock() may do initiative schedule when the 'sk' is owned by
other thread at the same time, we would receivce a warning message
that "scheduling while atomic".
Even worse, if the next task (selected by the scheduler) try to
release a 'sk', it need to request vsock_table_lock and the deadlock
occur, cause the system into softlockup state.
Call trace:
queued_spin_lock_slowpath
vsock_remove_bound
vsock_remove_sock
virtio_transport_release
__vsock_release
vsock_release
__sock_release
sock_close
__fput
____fput
So we should not require sk_lock in this case, just like the behavior
in vhost_vsock or vmci.
Fixes: 0ea9e1d3a9 ("VSOCK: Introduce virtio_transport.ko")
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/20210812053056.1699-1-longpeng2@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 88ca2521bd ]
There is a TOCTOU issue in set_evtchn_to_irq. Rows in the evtchn_to_irq
mapping are lazily allocated in this function. The check whether the row
is already present and the row initialization is not synchronized. Two
threads can at the same time allocate a new row for evtchn_to_irq and
add the irq mapping to the their newly allocated row. One thread will
overwrite what the other has set for evtchn_to_irq[row] and therefore
the irq mapping is lost. This will trigger a BUG_ON later in
bind_evtchn_to_cpu:
INFO: pci 0000:1a:15.4: [1d0f:8061] type 00 class 0x010802
INFO: nvme 0000:1a:12.1: enabling device (0000 -> 0002)
INFO: nvme nvme77: 1/0/0 default/read/poll queues
CRIT: kernel BUG at drivers/xen/events/events_base.c:427!
WARN: invalid opcode: 0000 [#1] SMP NOPTI
WARN: Workqueue: nvme-reset-wq nvme_reset_work [nvme]
WARN: RIP: e030:bind_evtchn_to_cpu+0xc2/0xd0
WARN: Call Trace:
WARN: set_affinity_irq+0x121/0x150
WARN: irq_do_set_affinity+0x37/0xe0
WARN: irq_setup_affinity+0xf6/0x170
WARN: irq_startup+0x64/0xe0
WARN: __setup_irq+0x69e/0x740
WARN: ? request_threaded_irq+0xad/0x160
WARN: request_threaded_irq+0xf5/0x160
WARN: ? nvme_timeout+0x2f0/0x2f0 [nvme]
WARN: pci_request_irq+0xa9/0xf0
WARN: ? pci_alloc_irq_vectors_affinity+0xbb/0x130
WARN: queue_request_irq+0x4c/0x70 [nvme]
WARN: nvme_reset_work+0x82d/0x1550 [nvme]
WARN: ? check_preempt_wakeup+0x14f/0x230
WARN: ? check_preempt_curr+0x29/0x80
WARN: ? nvme_irq_check+0x30/0x30 [nvme]
WARN: process_one_work+0x18e/0x3c0
WARN: worker_thread+0x30/0x3a0
WARN: ? process_one_work+0x3c0/0x3c0
WARN: kthread+0x113/0x130
WARN: ? kthread_park+0x90/0x90
WARN: ret_from_fork+0x3a/0x50
This patch sets evtchn_to_irq rows via a cmpxchg operation so that they
will be set only once. The row is now cleared before writing it to
evtchn_to_irq in order to not create a race once the row is visible for
other threads.
While at it, do not require the page to be zeroed, because it will be
overwritten with -1's in clear_evtchn_to_irq_row anyway.
Signed-off-by: Maximilian Heyne <mheyne@amazon.de>
Fixes: d0b075ffee ("xen/events: Refactor evtchn_to_irq array to be dynamically allocated")
Link: https://lore.kernel.org/r/20210812130930.127134-1-mheyne@amazon.de
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24d032e235 ]
The SFC_DONE register lives within the corresponding VD0/VD2/VD4/VD6
forcewake domain and is not accessible if the vdbox in that domain is
fused off and the forcewake is not initialized.
This mistake went unnoticed because until recently we were using the
wrong register offset for the SFC_DONE register; once the register
offset was corrected, we started hitting errors like
<4> [544.989065] i915 0000:cc:00.0: Uninitialized forcewake domain(s) 0x80 accessed at 0x1ce000
on parts with fused-off vdbox engines.
Fixes: e50dbdbfd9 ("drm/i915/tgl: Add SFC instdone to error state")
Fixes: 9c9c6d0ab0 ("drm/i915: Correct SFC_DONE register offset")
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210806174130.1058960-1-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
(cherry picked from commit c5589bb5dc)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[Changed Fixes tag to match the cherry-picked 82929a2140]
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6de035fec0 ]
Currently if BBR congestion control is initialized after more than 2B
packets have been delivered, depending on the phase of the
tp->delivered counter the tracking of BBR round trips can get stuck.
The bug arises because if tp->delivered is between 2^31 and 2^32 at
the time the BBR congestion control module is initialized, then the
initialization of bbr->next_rtt_delivered to 0 will cause the logic to
believe that the end of the round trip is still billions of packets in
the future. More specifically, the following check will fail
repeatedly:
!before(rs->prior_delivered, bbr->next_rtt_delivered)
and thus the connection will take up to 2B packets delivered before
that check will pass and the connection will set:
bbr->round_start = 1;
This could cause many mechanisms in BBR to fail to trigger, for
example bbr_check_full_bw_reached() would likely never exit STARTUP.
This bug is 5 years old and has not been observed, and as a practical
matter this would likely rarely trigger, since it would require
transferring at least 2B packets, or likely more than 3 terabytes of
data, before switching congestion control algorithms to BBR.
This patch is a stable candidate for kernels as far back as v4.9,
when tcp_bbr.c was added.
Fixes: 0f8782ea14 ("tcp_bbr: add BBR congestion control")
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Kevin Yang <yyd@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20210811024056.235161-1-ncardwell@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6922110d15 ]
After migrating my laptop from 4.19-LTS to 5.4-LTS a while ago I noticed
that my Ethernet port to which a bond and a VLAN interface are attached
appeared to remain up after resuming from suspend with the cable unplugged
(and that problem still persists with 5.10-LTS).
It happens that the following happens:
- the network driver (e1000e here) prepares to suspend, calls e1000e_down()
which calls netif_carrier_off() to signal that the link is going down.
- netif_carrier_off() adds a link_watch event to the list of events for
this device
- the device is completely stopped.
- the machine suspends
- the cable is unplugged and the machine brought to another location
- the machine is resumed
- the queued linkwatch events are processed for the device
- the device doesn't yet have the __LINK_STATE_PRESENT bit and its events
are silently dropped
- the device is resumed with its link down
- the upper VLAN and bond interfaces are never notified that the link had
been turned down and remain up
- the only way to provoke a change is to physically connect the machine
to a port and possibly unplug it.
The state after resume looks like this:
$ ip -br li | egrep 'bond|eth'
bond0 UP e8:6a:64:64:64:64 <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP>
eth0 DOWN e8:6a:64:64:64:64 <NO-CARRIER,BROADCAST,MULTICAST,SLAVE,UP>
eth0.2@eth0 UP e8:6a:64:64:64:64 <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP>
Placing an explicit call to netdev_state_change() either in the suspend
or the resume code in the NIC driver worked around this but the solution
is not satisfying.
The issue in fact really is in link_watch that loses events while it
ought not to. It happens that the test for the device being present was
added by commit 124eee3f69 ("net: linkwatch: add check for netdevice
being present to linkwatch_do_dev") in 4.20 to avoid an access to
devices that are not present.
Instead of dropping events, this patch proceeds slightly differently by
postponing their handling so that they happen after the device is fully
resumed.
Fixes: 124eee3f69 ("net: linkwatch: add check for netdevice being present to linkwatch_do_dev")
Link: https://lists.openwall.net/netdev/2018/03/15/62
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Link: https://lore.kernel.org/r/20210809160628.22623-1-w@1wt.eu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45a687879b ]
Ignore fdb flags when adding port extern learn entries and always set
BR_FDB_LOCAL flag when adding bridge extern learn entries. This is
closest to the behaviour we had before and avoids breaking any use cases
which were allowed.
This patch fixes iproute2 calls which assume NUD_PERMANENT and were
allowed before, example:
$ bridge fdb add 00:11:22:33:44:55 dev swp1 extern_learn
Extern learn entries are allowed to roam, but do not expire, so static
or dynamic flags make no sense for them.
Also add a comment for future reference.
Fixes: eb100e0e24 ("net: bridge: allow to add externally learned entries from user-space")
Fixes: 0541a62932 ("net: bridge: validate the NUD_PERMANENT bit when adding an extern_learn FDB entry")
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20210810110010.43859-1-razor@blackwall.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0541a62932 ]
Currently it is possible to add broken extern_learn FDB entries to the
bridge in two ways:
1. Entries pointing towards the bridge device that are not local/permanent:
ip link add br0 type bridge
bridge fdb add 00:01:02:03:04:05 dev br0 self extern_learn static
2. Entries pointing towards the bridge device or towards a port that
are marked as local/permanent, however the bridge does not process the
'permanent' bit in any way, therefore they are recorded as though they
aren't permanent:
ip link add br0 type bridge
bridge fdb add 00:01:02:03:04:05 dev br0 self extern_learn permanent
Since commit 52e4bec155 ("net: bridge: switchdev: treat local FDBs the
same as entries towards the bridge"), these incorrect FDB entries can
even trigger NULL pointer dereferences inside the kernel.
This is because that commit made the assumption that all FDB entries
that are not local/permanent have a valid destination port. For context,
local / permanent FDB entries either have fdb->dst == NULL, and these
point towards the bridge device and are therefore local and not to be
used for forwarding, or have fdb->dst == a net_bridge_port structure
(but are to be treated in the same way, i.e. not for forwarding).
That assumption _is_ correct as long as things are working correctly in
the bridge driver, i.e. we cannot logically have fdb->dst == NULL under
any circumstance for FDB entries that are not local. However, the
extern_learn code path where FDB entries are managed by a user space
controller show that it is possible for the bridge kernel driver to
misinterpret the NUD flags of an entry transmitted by user space, and
end up having fdb->dst == NULL while not being a local entry. This is
invalid and should be rejected.
Before, the two commands listed above both crashed the kernel in this
check from br_switchdev_fdb_notify:
struct net_device *dev = info.is_local ? br->dev : dst->dev;
info.is_local == false, dst == NULL.
After this patch, the invalid entry added by the first command is
rejected:
ip link add br0 type bridge && bridge fdb add 00:01:02:03:04:05 dev br0 self extern_learn static; ip link del br0
Error: bridge: FDB entry towards bridge must be permanent.
and the valid entry added by the second command is properly treated as a
local address and does not crash br_switchdev_fdb_notify anymore:
ip link add br0 type bridge && bridge fdb add 00:01:02:03:04:05 dev br0 self extern_learn permanent; ip link del br0
Fixes: eb100e0e24 ("net: bridge: allow to add externally learned entries from user-space")
Reported-by: syzbot+9ba1174359adba5a5b7c@syzkaller.appspotmail.com
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Link: https://lore.kernel.org/r/20210801231730.7493-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21b52fed92 ]
rtnl_fdb_dump() has logic to split a dump of PF_BRIDGE neighbors into
multiple netlink skbs if the buffer provided by user space is too small
(one buffer will typically handle a few hundred FDB entries).
When the current buffer becomes full, nlmsg_put() in
dsa_slave_port_fdb_do_dump() returns -EMSGSIZE and DSA saves the index
of the last dumped FDB entry, returns to rtnl_fdb_dump() up to that
point, and then the dump resumes on the same port with a new skb, and
FDB entries up to the saved index are simply skipped.
Since dsa_slave_port_fdb_do_dump() is pointed to by the "cb" passed to
drivers, then drivers must check for the -EMSGSIZE error code returned
by it. Otherwise, when a netlink skb becomes full, DSA will no longer
save newly dumped FDB entries to it, but the driver will continue
dumping. So FDB entries will be missing from the dump.
Fix the broken backpressure by propagating the "cb" return code and
allow rtnl_fdb_dump() to restart the FDB dump with a new skb.
Fixes: 291d1e72b7 ("net: dsa: sja1105: Add support for FDB and MDB management")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 871a73a1c8 ]
rtnl_fdb_dump() has logic to split a dump of PF_BRIDGE neighbors into
multiple netlink skbs if the buffer provided by user space is too small
(one buffer will typically handle a few hundred FDB entries).
When the current buffer becomes full, nlmsg_put() in
dsa_slave_port_fdb_do_dump() returns -EMSGSIZE and DSA saves the index
of the last dumped FDB entry, returns to rtnl_fdb_dump() up to that
point, and then the dump resumes on the same port with a new skb, and
FDB entries up to the saved index are simply skipped.
Since dsa_slave_port_fdb_do_dump() is pointed to by the "cb" passed to
drivers, then drivers must check for the -EMSGSIZE error code returned
by it. Otherwise, when a netlink skb becomes full, DSA will no longer
save newly dumped FDB entries to it, but the driver will continue
dumping. So FDB entries will be missing from the dump.
Fix the broken backpressure by propagating the "cb" return code and
allow rtnl_fdb_dump() to restart the FDB dump with a new skb.
Fixes: 58c59ef9e9 ("net: dsa: lantiq: Add Forwarding Database access")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ada2fee185 ]
rtnl_fdb_dump() has logic to split a dump of PF_BRIDGE neighbors into
multiple netlink skbs if the buffer provided by user space is too small
(one buffer will typically handle a few hundred FDB entries).
When the current buffer becomes full, nlmsg_put() in
dsa_slave_port_fdb_do_dump() returns -EMSGSIZE and DSA saves the index
of the last dumped FDB entry, returns to rtnl_fdb_dump() up to that
point, and then the dump resumes on the same port with a new skb, and
FDB entries up to the saved index are simply skipped.
Since dsa_slave_port_fdb_do_dump() is pointed to by the "cb" passed to
drivers, then drivers must check for the -EMSGSIZE error code returned
by it. Otherwise, when a netlink skb becomes full, DSA will no longer
save newly dumped FDB entries to it, but the driver will continue
dumping. So FDB entries will be missing from the dump.
Fix the broken backpressure by propagating the "cb" return code and
allow rtnl_fdb_dump() to restart the FDB dump with a new skb.
Fixes: ab335349b8 ("net: dsa: lan9303: Add port_fast_age and port_fdb_dump methods")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 164844135a ]
Currently ksz8_port_vlan_filtering() sets or clears the VLAN Enable
hardware flag. That controls discarding of packets with a VID that
has not been enabled for any port on the switch.
Since it is a global flag, set the dsa_switch::vlan_filtering_is_global
flag so that the DSA core understands this can't be controlled per
port.
When VLAN filtering is enabled, the switch should also discard packets
with a VID that's not enabled on the ingress port. Set or clear each
external port's VLAN Ingress Filter flag in ksz8_port_vlan_filtering()
to make that happen.
Fixes: e66f840c08 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver")
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c34f674c88 ]
ksz_read64() currently does some dubious byte-swapping on the two
halves of a 64-bit register, and then only returns the high bits.
Replace this with a straightforward expression.
Fixes: e66f840c08 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver")
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 563476ae0c ]
The CQ destroy is performed based on the IRQ number that is stored in
cq->irqn. That number wasn't set explicitly during CQ creation and as
expected some of the API users of mlx5_core_create_cq() forgot to update
it.
This caused to wrong synchronization call of the wrong IRQ with a number
0 instead of the real one.
As a fix, set the IRQ number directly in the mlx5_core_create_cq() and
update all users accordingly.
Fixes: 1a86b377aa ("vdpa/mlx5: Add VDPA driver for supported mlx5 devices")
Fixes: ef1659ade3 ("IB/mlx5: Add DEVX support for CQ events")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ba7f53f8b ]
In some circumstances, such as with bridging, it's possible that the
stack will add the device's own MAC address to its unicast address list.
If, later, the stack deletes this address, the driver will receive a
request to remove this address.
The driver stores its current MAC address as part of the VSI MAC filter
list instead of separately. So, this causes a problem when the device's
MAC address is deleted unexpectedly, which results in traffic failure in
some cases.
The following configuration steps will reproduce the previously
mentioned problem:
> ip link set eth0 up
> ip link add dev br0 type bridge
> ip link set br0 up
> ip addr flush dev eth0
> ip link set eth0 master br0
> echo 1 > /sys/class/net/br0/bridge/vlan_filtering
> modprobe -r veth
> modprobe -r bridge
> ip addr add 192.168.1.100/24 dev eth0
The following ping command fails due to the netdev->dev_addr being
deleted when removing the bridge module.
> ping <link partner>
Fix this by making sure to not delete the netdev->dev_addr during MAC
address sync. After fixing this issue it was noticed that the
netdev_warn() in .set_mac was overly verbose, so make it at
netdev_dbg().
Also, there is a possibility of a race condition between .set_mac and
.set_rx_mode. Fix this by calling netif_addr_lock_bh() and
netif_addr_unlock_bh() on the device's netdev when the netdev->dev_addr
is going to be updated in .set_mac.
Fixes: e94d447866 ("ice: Implement filter sync, NDO operations and bump version")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Liang Li <liali@redhat.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50ac747984 ]
The userspace utility "driverctl" can be used to change/override the
system's default driver choices. This is useful in some situations
(buggy driver, old driver missing a device ID, trying a workaround,
etc.) where the user needs to load a different driver.
However, this is also prone to user error, where a driver is mapped
to a device it's not designed to drive. For example, if the ice driver
is mapped to driver iavf devices, the ice driver crashes.
Add a check to return an error if the ice driver is being used to
probe a virtual function.
Fixes: 837f08fdec ("ice: Add basic driver framework for Intel(R) E800 Series")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d09c548dbf ]
When mirror/redirect a skb to a different port, the ct info should be reset
for reclassification. Or the pkts will match unexpected rules. For example,
with following topology and commands:
-----------
|
veth0 -+-------
|
veth1 -+-------
|
------------
tc qdisc add dev veth0 clsact
# The same with "action mirred egress mirror dev veth1" or "action mirred ingress redirect dev veth1"
tc filter add dev veth0 egress chain 1 protocol ip flower ct_state +trk action mirred ingress mirror dev veth1
tc filter add dev veth0 egress chain 0 protocol ip flower ct_state -inv action ct commit action goto chain 1
tc qdisc add dev veth1 clsact
tc filter add dev veth1 ingress chain 0 protocol ip flower ct_state +trk action drop
ping <remove ip via veth0> &
tc -s filter show dev veth1 ingress
With command 'tc -s filter show', we can find the pkts were dropped on
veth1.
Fixes: b57dc7c13e ("net/sched: Introduce action ct")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f3d65c166 ]
There can be a race between the waiters for a tx work request buffer
and the link down processing that finally clears the link. Although
all waiters are woken up before the link is cleared there might be
waiters which did not yet get back control and are still waiting.
This results in an access to a cleared wait queue head.
Fix this by introducing atomic reference counting around the wait calls,
and wait with the link clear processing until all waiters have finished.
Move the work request layer related calls into smc_wr.c and set the
link state to INACTIVE before calling smcr_link_clear() in
smc_llc_srv_add_link().
Fixes: 15e1b99aad ("net/smc: no WR buffer wait for terminating link group")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2459dcb96b ]
IFLA_IFNAME is nul-term string which means that IFLA_IFNAME buffer can be
larger than length of string which contains.
Function __rtnl_newlink() generates new own ifname if either IFLA_IFNAME
was not specified at all or userspace passed empty nul-term string.
It is expected that if userspace does not specify ifname for new ppp netdev
then kernel generates one in format "ppp<id>" where id matches to the ppp
unit id which can be later obtained by PPPIOCGUNIT ioctl.
And it works in this way if IFLA_IFNAME is not specified at all. But it
does not work when IFLA_IFNAME is specified with empty string.
So fix this logic also for empty IFLA_IFNAME in ppp_nl_newlink() function
and correctly generates ifname based on ppp unit identifier if userspace
did not provided preferred ifname.
Without this patch when IFLA_IFNAME was specified with empty string then
kernel created a new ppp interface in format "ppp<id>" but id did not
match ppp unit id returned by PPPIOCGUNIT ioctl. In this case id was some
number generated by __rtnl_newlink() function.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: bb8082f691 ("ppp: build ifname using unit identifier for rtnl based devices")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2383cb9497 ]
Commit a5e63c7d38 "net: phy: micrel: Fix detection of ksz87xx
switch" broke link detection on the external ports of the KSZ8795.
The previously unused phy_driver structure for these devices specifies
config_aneg and read_status functions that appear to be designed for a
fixed link and do not work with the embedded PHYs in the KSZ8795.
Delete the use of these functions in favour of the generic PHY
implementations which were used previously.
Fixes: a5e63c7d38 ("net: phy: micrel: Fix detection of ksz87xx switch")
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4eb1f4032 ]
In __htab_map_lookup_and_delete_batch(), hash buckets are iterated
over to count the number of elements in each bucket (bucket_size).
If bucket_size is large enough, the multiplication to calculate
kvmalloc() size could overflow, resulting in out-of-bounds write
as reported by KASAN:
[...]
[ 104.986052] BUG: KASAN: vmalloc-out-of-bounds in __htab_map_lookup_and_delete_batch+0x5ce/0xb60
[ 104.986489] Write of size 4194224 at addr ffffc9010503be70 by task crash/112
[ 104.986889]
[ 104.987193] CPU: 0 PID: 112 Comm: crash Not tainted 5.14.0-rc4 #13
[ 104.987552] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014
[ 104.988104] Call Trace:
[ 104.988410] dump_stack_lvl+0x34/0x44
[ 104.988706] print_address_description.constprop.0+0x21/0x140
[ 104.988991] ? __htab_map_lookup_and_delete_batch+0x5ce/0xb60
[ 104.989327] ? __htab_map_lookup_and_delete_batch+0x5ce/0xb60
[ 104.989622] kasan_report.cold+0x7f/0x11b
[ 104.989881] ? __htab_map_lookup_and_delete_batch+0x5ce/0xb60
[ 104.990239] kasan_check_range+0x17c/0x1e0
[ 104.990467] memcpy+0x39/0x60
[ 104.990670] __htab_map_lookup_and_delete_batch+0x5ce/0xb60
[ 104.990982] ? __wake_up_common+0x4d/0x230
[ 104.991256] ? htab_of_map_free+0x130/0x130
[ 104.991541] bpf_map_do_batch+0x1fb/0x220
[...]
In hashtable, if the elements' keys have the same jhash() value, the
elements will be put into the same bucket. By putting a lot of elements
into a single bucket, the value of bucket_size can be increased to
trigger the integer overflow.
Triggering the overflow is possible for both callers with CAP_SYS_ADMIN
and callers without CAP_SYS_ADMIN.
It will be trivial for a caller with CAP_SYS_ADMIN to intentionally
reach this overflow by enabling BPF_F_ZERO_SEED. As this flag will set
the random seed passed to jhash() to 0, it will be easy for the caller
to prepare keys which will be hashed into the same value, and thus put
all the elements into the same bucket.
If the caller does not have CAP_SYS_ADMIN, BPF_F_ZERO_SEED cannot be
used. However, it will be still technically possible to trigger the
overflow, by guessing the random seed value passed to jhash() (32bit)
and repeating the attempt to trigger the overflow. In this case,
the probability to trigger the overflow will be low and will take
a very long time.
Fix the integer overflow by calling kvmalloc_array() instead of
kvmalloc() to allocate memory.
Fixes: 057996380a ("bpf: Add batch ops to all htab bpf map")
Signed-off-by: Tatsuhiko Yasumatsu <th.yasumatsu@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210806150419.109658-1-th.yasumatsu@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d7b132e62 ]
The gpiod_lookup_table.table passed to gpiod_add_lookup_table() must
be terminated with an empty entry, add this.
Note we have likely been getting away with this not being present because
the GPIO lookup code first matches on the dev_id, causing most lookups to
skip checking the table and the lookups which do check the table will
find a matching entry before reaching the end. With that said, terminating
these tables properly still is obviously the correct thing to do.
Fixes: f8eb0235f6 ("x86: pcengines apuv2 gpio/leds/keys platform driver")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210806115515.12184-1-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 704e624f7b ]
On s390, the following build warning occurs:
drivers/net/ethernet/marvell/mvpp2/mvpp2.h:844:2: warning: overflow in
conversion from 'long unsigned int' to 'int' changes value from
'18446744073709551584' to '-32' [-Woverflow]
844 | ((total_size) - MVPP2_SKB_HEADROOM - MVPP2_SKB_SHINFO_SIZE)
This happens because MVPP2_SKB_SHINFO_SIZE, which is 320 bytes (which is
already 64-byte aligned) on some architectures, actually gets ALIGN'd up
to 512 bytes in the s390 case.
So then, when this is invoked:
MVPP2_RX_MAX_PKT_SIZE(MVPP2_BM_SHORT_FRAME_SIZE)
...that turns into:
704 - 224 - 512 == -32
...which is not a good frame size to end up with! The warning above is a
bit lucky: it notices a signed/unsigned bad behavior here, which leads
to the real problem of a frame that is too short for its contents.
Increase MVPP2_BM_SHORT_FRAME_SIZE by 32 (from 704 to 736), which is
just exactly big enough. (The other values can't readily be changed
without causing a lot of other problems.)
Fixes: 07dd0a7aae ("mvpp2: add basic XDP support")
Cc: Sven Auhagen <sven.auhagen@voleatech.de>
Cc: Matteo Croce <mcroce@microsoft.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aff51c5da3 ]
Add the missing RxUnicast counter.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 38ea9def5b ]
It should be added kfree_skb_list() when err is not equal to zero
in nf_br_ip_fragment().
v2: keep this aligned with IPv6.
v3: modify iter.frag_list to iter.frag.
Fixes: 3c171f496e ("netfilter: bridge: add connection tracking system")
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b353bbeae ]
The driver was defining two ALSA controls that both change the same
register field for the wind noise filter corner frequency. The filter
response has two corners, at different frequencies, and the duplicate
controls most likely were an attempt to be able to set the value using
either of the frequencies.
However, having two controls changing the same field can be problematic
and it is unnecessary. Both frequencies are related to each other so
setting one implies exactly what the other would be.
Removing a control affects user-side code, but there is currently no
known use of the removed control so it would be best to remove it now
before it becomes a problem.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2c394ca796 ("ASoC: Add support for CS42L42 codec")
Link: https://lore.kernel.org/r/20210803160834.9005-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 798a315fc3 ]
Some pin doesn't support PUPD register, if it fails and fallbacks with
bias_set_combo case, it will call mtk_pinconf_bias_set_pupd_r1_r0() to
modify the PUPD pin again.
Since the general bias set are either PU/PD or PULLSEL/PULLEN, try
bias_set or bias_set_rev1 for the other fallback case. If the pin
doesn't support neither PU/PD nor PULLSEL/PULLEN, it will return
-ENOTSUPP.
Fixes: 81bd1579b4 ("pinctrl: mediatek: Fix fallback call path")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Link: https://lore.kernel.org/r/20210701080955.2660294-1-hsinyi@chromium.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b93dfa6bda upstream.
Fix the NFIT parsing code to treat a 0 index in a SPA Range Structure as
a special case and not match Region Mapping Structures that use 0 to
indicate that they are not mapped. Without this fix some platform BIOS
descriptions of "virtual disk" ranges do not result in the pmem driver
attaching to the range.
Details:
In addition to typical persistent memory ranges, the ACPI NFIT may also
convey "virtual" ranges. These ranges are indicated by a UUID in the SPA
Range Structure of UUID_VOLATILE_VIRTUAL_DISK, UUID_VOLATILE_VIRTUAL_CD,
UUID_PERSISTENT_VIRTUAL_DISK, or UUID_PERSISTENT_VIRTUAL_CD. The
critical difference between virtual ranges and UUID_PERSISTENT_MEMORY,
is that virtual do not support associations with Region Mapping
Structures. For this reason the "index" value of virtual SPA Range
Structures is allowed to be 0. If a platform BIOS decides to represent
NVDIMMs with disconnected "Region Mapping Structures" (range-index ==
0), the kernel may falsely associate them with standalone ranges where
the "SPA Range Structure Index" is also zero. When this happens the
driver may falsely require labels where "virtual disks" are expected to
be label-less. I.e. "label-less" is where the namespace-range ==
region-range and the pmem driver attaches with no user action to create
a namespace.
Cc: Jacek Zloch <jacek.zloch@intel.com>
Cc: Lukasz Sobieraj <lukasz.sobieraj@intel.com>
Cc: "Lee, Chun-Yi" <jlee@suse.com>
Cc: <stable@vger.kernel.org>
Fixes: c2f32acdf8 ("acpi, nfit: treat virtual ramdisk SPA as pmem region")
Reported-by: Krzysztof Rusocki <krzysztof.rusocki@intel.com>
Reported-by: Damian Bassa <damian.bassa@intel.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Link: https://lore.kernel.org/r/162870796589.2521182.1240403310175570220.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf2ba43221 upstream.
Function ceph_check_delayed_caps() is called from the mdsc->delayed_work
workqueue and it can be kept looping for quite some time if caps keep
being added back to the mdsc->cap_delay_list. This may result in the
watchdog tainting the kernel with the softlockup flag.
This patch breaks this loop if the caps have been recently (i.e. during
the loop execution). Any new caps added to the list will be handled in
the next run.
Also, allow schedule_delayed() callers to explicitly set the delay value
instead of defaulting to 5s, so we can ensure that it runs soon
afterward if it looks like there is more work.
Cc: stable@vger.kernel.org
URL: https://tracker.ceph.com/issues/46284
Signed-off-by: Luis Henriques <lhenriques@suse.de>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a715e8040 upstream.
FPU_STATUS register contains FP exception flags bits which are updated
by core as side-effect of FP instructions but can also be manually
wiggled such as by glibc C99 functions fe{raise,clear,test}except() etc.
To effect the update, the programming model requires OR'ing FWE
bit (31). This bit is write-only and RAZ, meaning it is effectively
auto-cleared after write and thus needs to be set everytime: which
is how glibc implements this.
However there's another usecase of FPU_STATUS update, at the time of
Linux task switch when incoming task value needs to be programmed into
the register. This was added as part of f45ba2bd6d ("ARCv2:
fpu: preserve userspace fpu state") which missed OR'ing FWE bit,
meaning the new value is effectively not being written at all.
This patch remedies that.
Interestingly, this snafu was not caught in interm glibc testing as the
race window which relies on a specific exception bit to be set/clear is
really small specially when it nvolves context switch.
Fortunately this was caught by glibc's math/test-fenv-tls test which
repeatedly set/clear exception flags in a big loop, concurrently in main
program and also in a thread.
Fixes: https://github.com/foss-for-synopsys-dwc-arc-processors/linux/issues/54
Fixes: f45ba2bd6d ("ARCv2: fpu: preserve userspace fpu state")
Cc: stable@vger.kernel.org #5.6+
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit acc68b8d2a upstream.
The CPSW switchdev driver inherited fix from commit 9421c90150 ("net:
ethernet: ti: cpsw: fix min eth packet size") which changes min TX packet
size to 64bytes (VLAN_ETH_ZLEN, excluding ETH_FCS). It was done to fix HW
packed drop issue when packets are sent from Host to the port with PVID and
un-tagging enabled. Unfortunately this breaks some other non-switch
specific use-cases, like:
- [1] CPSW port as DSA CPU port with DSA-tag applied at the end of the
packet
- [2] Some industrial protocols, which expects min TX packet size 60Bytes
(excluding FCS).
Fix it by configuring min TX packet size depending on driver mode
- 60Bytes (ETH_ZLEN) for multi mac (dual-mac) mode
- 64Bytes (VLAN_ETH_ZLEN) for switch mode
and update it during driver mode change and annotate with
READ_ONCE()/WRITE_ONCE() as it can be read by napi while writing.
[1] https://lore.kernel.org/netdev/20210531124051.GA15218@cephalopod/
[2] https://e2e.ti.com/support/arm/sitara_arm/f/791/t/701669
Cc: stable@vger.kernel.org
Fixes: ed3525eda4 ("net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac")
Reported-by: Ben Hutchings <ben.hutchings@essensium.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d3fc01796 upstream.
We used to follow the rule earlier that the create SD context
always be a multiple of 8. However, with the change:
cifs: refactor create_sd_buf() and and avoid corrupting the buffer
...we recompute the length, and we failed that rule.
Fixing that with this change.
Cc: <stable@vger.kernel.org> # v5.10+
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 86ff25ed6c upstream.
If an i2c driver happens to not provide the full amount of data that a
user asks for, it is possible that some uninitialized data could be sent
to userspace. While all in-kernel drivers look to be safe, just be sure
by initializing the buffer to zero before it is passed to the i2c driver
so that any future drivers will not have this issue.
Also properly copy the amount of data recvieved to the userspace buffer,
as pointed out by Dan Carpenter.
Reported-by: Eric Dumazet <edumazet@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c39ca6885 upstream.
The tlv320aic31xx driver relies on regcache_sync() to restore the register
contents after going to _BIAS_OFF, for example during system suspend. This
does not work for the jack detection configuration since that is configured
via the same register that status is read back from so the register is
volatile and not cached. This can also cause issues during init if the jack
detection ends up getting set up before the CODEC is initially brought out
of _BIAS_OFF, we will reset the CODEC and resync the cache as part of that
process.
Fix this by explicitly reapplying the jack detection configuration after
resyncing the register cache during power on.
This issue was found by an engineer working off-list on a product
kernel, I just wrote up the upstream fix.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210723180200.25105-1-broonie@kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 827f3164aa upstream.
Along with the transition to the managed PCM buffers, the driver now
accepts the dynamically allocated buffer, while it still kept the
reference to the old preallocated buffer address. This patch corrects
to the right reference via runtime->dma_addr.
(Although this might have been already buggy before the cleanup with
the managed buffer, let's put Fixes tag to point that; it's a corner
case, after all.)
Fixes: d55894bc27 ("ASoC: uniphier: Use managed buffer allocation")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20210728112353.6675-5-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0d62baa7f upstream.
Printing kernel pointers is discouraged because they might leak kernel
memory layout. This fixes smatch warning:
drivers/net/ethernet/xilinx/xilinx_emaclite.c:1191 xemaclite_of_probe() warn:
argument 4 to %08lX specifier is cast from pointer
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pavel Machek (CIP) <pavel@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 427215d85e upstream.
Add the following checks from __do_loopback() to clone_private_mount() as
well:
- verify that the mount is in the current namespace
- verify that there are no locked children
Reported-by: Alois Wohlschlager <alois1@gmx-topmail.de>
Fixes: c771d683a6 ("vfs: introduce clone_private_mount()")
Cc: <stable@vger.kernel.org> # v3.18
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3125f26c51 upstream.
When registering new ppp interface via PPPIOCNEWUNIT ioctl then kernel has
to choose interface name as this ioctl API does not support specifying it.
Kernel in this case register new interface with name "ppp<id>" where <id>
is the ppp unit id, which can be obtained via PPPIOCGUNIT ioctl. This
applies also in the case when registering new ppp interface via rtnl
without supplying IFLA_IFNAME.
PPPIOCNEWUNIT ioctl allows to specify own ppp unit id which will kernel
assign to ppp interface, in case this ppp id is not already used by other
ppp interface.
In case user does not specify ppp unit id then kernel choose the first free
ppp unit id. This applies also for case when creating ppp interface via
rtnl method as it does not provide a way for specifying own ppp unit id.
If some network interface (does not have to be ppp) has name "ppp<id>"
with this first free ppp id then PPPIOCNEWUNIT ioctl or rtnl call fails.
And registering new ppp interface is not possible anymore, until interface
which holds conflicting name is renamed. Or when using rtnl method with
custom interface name in IFLA_IFNAME.
As list of allocated / used ppp unit ids is not possible to retrieve from
kernel to userspace, userspace has no idea what happens nor which interface
is doing this conflict.
So change the algorithm how ppp unit id is generated. And choose the first
number which is not neither used as ppp unit id nor in some network
interface with pattern "ppp<id>".
This issue can be simply reproduced by following pppd call when there is no
ppp interface registered and also no interface with name pattern "ppp<id>":
pppd ifname ppp1 +ipv6 noip noauth nolock local nodetach pty "pppd +ipv6 noip noauth nolock local nodetach notty"
Or by creating the one ppp interface (which gets assigned ppp unit id 0),
renaming it to "ppp1" and then trying to create a new ppp interface (which
will always fails as next free ppp unit id is 1, but network interface with
name "ppp1" exists).
This patch fixes above described issue by generating new and new ppp unit
id until some non-conflicting id with network interfaces is generated.
Signed-off-by: Pali Rohár <pali@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc0dc8a73e upstream.
The recent fix c4824ae7db ("ALSA: pcm: Fix mmap capability check")
restricts the mmap capability only to the drivers that properly set up
the buffers, but it caused a regression for a few drivers that manage
the buffer on its own way.
For those with UNKNOWN buffer type (i.e. the uninitialized / unused
substream->dma_buffer), just assume that the driver handles the mmap
properly and blindly trust the hardware info bit.
Fixes: c4824ae7db ("ALSA: pcm: Fix mmap capability check")
Reported-and-tested-by: Jeff Woods <jwoods@fnordco.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/s5him0gpghv.wl-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26b75952ca upstream.
Kunpeng920's EHCI controller does not have SBRN register.
Reading the SBRN register when the controller driver is
initialized will get 0.
When rebooting the EHCI driver, ehci_shutdown() will be called.
if the sbrn flag is 0, ehci_shutdown() will return directly.
The sbrn flag being 0 will cause the EHCI interrupt signal to
not be turned off after reboot. this interrupt that is not closed
will cause an exception to the device sharing the interrupt.
Therefore, the EHCI controller of Kunpeng920 needs to skip
the read operation of the SBRN register.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Longfang Liu <liulongfang@huawei.com>
Link: https://lore.kernel.org/r/1617958081-17999-1-git-send-email-liulongfang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab0c29687b upstream
Make vboxsf_dir_create() optionally return the vboxsf-handle for
the created file. This is a preparation patch for adding atomic_open
support.
Fixes: 0fd1695766 ("fs: Add VirtualBox guest shared folder (vboxsf) support")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc3ddee97c upstream
Honor the excl flag to the dir-inode create op, instead of behaving
as if it is always set.
Note the old behavior still worked most of the time since a non-exclusive
open only calls the create op, if there is a race and the file is created
between the dentry lookup and the calling of the create call.
While at it change the type of the is_dir parameter to the
vboxsf_dir_create() helper from an int to a bool, to be consistent with
the use of bool for the excl parameter.
Fixes: 0fd1695766 ("fs: Add VirtualBox guest shared folder (vboxsf) support")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ebc666f39f upstream
The RZ/G2 boards expect there to be an external clock reference for
USB2 EHCI controllers. For the Beacon boards, this reference clock
is controlled by a programmable versaclock. Because the RZ/G2
family has a special clock driver when using an external clock,
the third clock reference in the EHCI node needs to point to this
special clock, called usb2_clksel.
Since the usb2_clksel does not keep the usb_extal clock enabled,
the 4th clock entry for the EHCI nodes needs to reference it to
keep the clock running and make USB functional.
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20210513114617.30191-2-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 19eaad1400 which is
ee0415681e upstream.
This commit is not a stable candidate and was backported without needed
dependencies that results in the resctrl tests unable to compile.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51e1bb9eea upstream.
Back then, commit 96ae522795 ("bpf: Add bpf_probe_write_user BPF helper
to be called in tracers") added the bpf_probe_write_user() helper in order
to allow to override user space memory. Its original goal was to have a
facility to "debug, divert, and manipulate execution of semi-cooperative
processes" under CAP_SYS_ADMIN. Write to kernel was explicitly disallowed
since it would otherwise tamper with its integrity.
One use case was shown in cf9b1199de ("samples/bpf: Add test/example of
using bpf_probe_write_user bpf helper") where the program DNATs traffic
at the time of connect(2) syscall, meaning, it rewrites the arguments to
a syscall while they're still in userspace, and before the syscall has a
chance to copy the argument into kernel space. These days we have better
mechanisms in BPF for achieving the same (e.g. for load-balancers), but
without having to write to userspace memory.
Of course the bpf_probe_write_user() helper can also be used to abuse
many other things for both good or bad purpose. Outside of BPF, there is
a similar mechanism for ptrace(2) such as PTRACE_PEEK{TEXT,DATA} and
PTRACE_POKE{TEXT,DATA}, but would likely require some more effort.
Commit 96ae522795 explicitly dedicated the helper for experimentation
purpose only. Thus, move the helper's availability behind a newly added
LOCKDOWN_BPF_WRITE_USER lockdown knob so that the helper is disabled under
the "integrity" mode. More fine-grained control can be implemented also
from LSM side with this change.
Fixes: 96ae522795 ("bpf: Add bpf_probe_write_user BPF helper to be called in tracers")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 914ab19e47 ]
Implement a .shutdown hook that will be called during a kexec operation
so that the TEE shared memory, session, and context that were set up
during .probe can be properly freed/closed.
Additionally, don't use dma-buf backed shared memory for the
fw_shm_pool. dma-buf backed shared memory cannot be reliably freed and
unregistered during a kexec operation even when tee_shm_free() is called
on the shm from a .shutdown hook. The problem occurs because
dma_buf_put() calls fput() which then uses task_work_add(), with the
TWA_RESUME parameter, to queue tee_shm_release() to be called before the
current task returns to user mode. However, the current task never
returns to user mode before the kexec completes so the memory is never
freed nor unregistered.
Use tee_shm_alloc_kernel_buf() to avoid dma-buf backed shared memory
allocation so that tee_shm_free() can directly call tee_shm_release().
This will ensure that the shm can be freed and unregistered during a
kexec operation.
Fixes: 246880958a ("firmware: broadcom: add OP-TEE based BNXT f/w manager")
Cc: stable@vger.kernel.org
Signed-off-by: Allen Pais <apais@linux.microsoft.com>
Co-developed-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Signed-off-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 376e4199e3 ]
Currently TEE_SHM_DMA_BUF flag has been inappropriately used to not
register shared memory allocated for private usage by underlying TEE
driver: OP-TEE in this case. So rather add a new flag as TEE_SHM_PRIV
that can be utilized by underlying TEE drivers for private allocation
and usage of shared memory.
With this corrected, allow tee_shm_alloc_kernel_buf() to allocate a
shared memory region without the backing of dma-buf.
Cc: stable@vger.kernel.org
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Co-developed-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Signed-off-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 179c6c27bf ]
Use the raw ASID, not ASID-1, when nullifying the last used VMCB when
freeing an SEV ASID. The consumer, pre_sev_run(), indexes the array by
the raw ASID, thus KVM could get a false negative when checking for a
different VMCB if KVM manages to reallocate the same ASID+VMCB combo for
a new VM.
Note, this cannot cause a functional issue _in the current code_, as
pre_sev_run() also checks which pCPU last did VMRUN for the vCPU, and
last_vmentry_cpu is initialized to -1 during vCPU creation, i.e. is
guaranteed to mismatch on the first VMRUN. However, prior to commit
8a14fe4f0c ("kvm: x86: Move last_cpu into kvm_vcpu_arch as
last_vmentry_cpu"), SVM tracked pCPU on its own and zero-initialized the
last_cpu variable. Thus it's theoretically possible that older versions
of KVM could miss a TLB flush if the first VMRUN is on pCPU0 and the ASID
and VMCB exactly match those of a prior VM.
Fixes: 70cd94e60c ("KVM: SVM: VMRUN should use associated ASID when SEV is enabled")
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
See https://github.com/raspberrypi/linux/issues/3981
An unknown unsafe memory access can result in the ep_state variable
in xhci_virt_ep being trampled with a stuck SET_DEQ_PENDING state
despite successful completion of a Set TR Deq Pointer command.
All URB enqueue/dequeue calls for the endpoint will fail in this state
so no transfers are possible until the device is reconnected.
As a workaround, clear the flag if we see it set and issue a new Set
TR Deq command anyway - this should be harmless, as a prior Set TR Deq
command will only have been issued in the Stopped state, and if the
endpoint is Running then the controller is required to ignore it and
respond with a Context State Error event TRB.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
commit e30e8d46cf upstream.
Due to inconsistencies in the way we manipulate compat GPRs, we have a
few issues today:
* For audit and tracing, where error codes are handled as a (native)
long, negative error codes are expected to be sign-extended to the
native 64-bits, or they may fail to be matched correctly. Thus a
syscall which fails with an error may erroneously be identified as
failing.
* For ptrace, *all* compat return values should be sign-extended for
consistency with 32-bit arm, but we currently only do this for
negative return codes.
* As we may transiently set the upper 32 bits of some compat GPRs while
in the kernel, these can be sampled by perf, which is somewhat
confusing. This means that where a syscall returns a pointer above 2G,
this will be sign-extended, but will not be mistaken for an error as
error codes are constrained to the inclusive range [-4096, -1] where
no user pointer can exist.
To fix all of these, we must consistently use helpers to get/set the
compat GPRs, ensuring that we never write the upper 32 bits of the
return code, and always sign-extend when reading the return code. This
patch does so, with the following changes:
* We re-organise syscall_get_return_value() to always sign-extend for
compat tasks, and reimplement syscall_get_error() atop. We update
syscall_trace_exit() to use syscall_get_return_value().
* We consistently use syscall_set_return_value() to set the return
value, ensureing the upper 32 bits are never set unexpectedly.
* As the core audit code currently uses regs_return_value() rather than
syscall_get_return_value(), we special-case this for
compat_user_mode(regs) such that this will do the right thing. Going
forward, we should try to move the core audit code over to
syscall_get_return_value().
Cc: <stable@vger.kernel.org>
Reported-by: He Zhe <zhe.he@windriver.com>
Reported-by: weiyuchen <weiyuchen3@huawei.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20210802104200.21390-1-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
[Mark: trivial conflict resolution for v5.10.y]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f2ad3accef ]
We've gotten a number of reports about backlight control not
working on panels which indicate that they use aux backlight
control. A recent patch:
commit 2d73eabe29
Author: Camille Cho <Camille.Cho@amd.com>
Date: Thu Jul 8 18:28:37 2021 +0800
drm/amd/display: Only set default brightness for OLED
[Why]
We used to unconditionally set backlight path as AUX for panels capable
of backlight adjustment via DPCD in set default brightness.
[How]
This should be limited to OLED panel only since we control backlight via
PWM path for SDR mode in LCD HDR panel.
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Camille Cho <Camille.Cho@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Changes some other code to only use aux for backlight control on
OLED panels. The commit message seems to indicate that PWM should
be used for SDR mode on HDR panels. Do something similar for
backlight control in general. This may need to be revisited if and
when HDR started to get used.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1438
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=213715
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ad4df56cd ]
Clang detected a problem with rc possibly being unitialized
(when length is zero) in a recently added fallocate code path.
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92766c4628 ]
When calling the 'ql_wait_for_drvr_lock' and 'ql_adapter_reset', the driver
has already acquired the spin lock, so the driver should not call 'ssleep'
in atomic context.
This bug can be fixed by using 'mdelay' instead of 'ssleep'.
Reported-by: Letu Ren <fantasquex@gmail.com>
Signed-off-by: Letu Ren <fantasquex@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit caace6ca4e ]
This issue was noticed while debugging a shutdown issue where some
secondary CPUs are not being shutdown correctly. A fix for that [1] requires
that secondary cpus be offlined using the cpu_online_mask so that the
stop operation is a no-op if CPU HOTPLUG is disabled. I, like the author in
[1] looked at the architectures and found that alpha is one of two
architectures that executes smp_send_stop() on all possible CPUs.
On alpha, smp_send_stop() sends an IPI to all possible CPUs but only needs
to send them to online CPUs.
Send the stop IPI to only the online CPUs.
[1] https://lkml.org/lkml/2020/1/10/250
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 795e3d2ea6 ]
The list_for_each_entry() iterator, "vlan" in this code, can never be
NULL so the warning will never be printed.
Signed-off-by: Harshvardhan Jha <harshvardhan.jha@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ecef6a9eff ]
Data transfers are not required to be block aligned in memory, so they
span two pages. Fix this by splitting the call to >sff_data_xfer into
two for that case.
This has been broken since the initial libata import before the damn
of git, but was uncovered by the legacy ide driver removal.
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20210709130237.3730959-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
The backport of c9d9fdbc10 to 5.10 in
6976f3cf34 removed more than it should
have leading to 'batch' being used uninitialised. The 5.13 backport and
the mainline commit did not remove the portion this patch adds back.
Signed-off-by: Jonathan Gray <jsg@jsg.id.au>
Fixes: 6976f3cf34 ("drm/i915: Revert "drm/i915/gem: Asynchronous cmdparser"")
Cc: <stable@vger.kernel.org> # 5.10
Cc: Jason Ekstrand <jason@jlekstrand.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f558c2b834 upstream.
Double enqueues in rt runqueues (list) have been reported while running
a simple test that spawns a number of threads doing a short sleep/run
pattern while being concurrently setscheduled between rt and fair class.
WARNING: CPU: 3 PID: 2825 at kernel/sched/rt.c:1294 enqueue_task_rt+0x355/0x360
CPU: 3 PID: 2825 Comm: setsched__13
RIP: 0010:enqueue_task_rt+0x355/0x360
Call Trace:
__sched_setscheduler+0x581/0x9d0
_sched_setscheduler+0x63/0xa0
do_sched_setscheduler+0xa0/0x150
__x64_sys_sched_setscheduler+0x1a/0x30
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xae
list_add double add: new=ffff9867cb629b40, prev=ffff9867cb629b40,
next=ffff98679fc67ca0.
kernel BUG at lib/list_debug.c:31!
invalid opcode: 0000 [#1] PREEMPT_RT SMP PTI
CPU: 3 PID: 2825 Comm: setsched__13
RIP: 0010:__list_add_valid+0x41/0x50
Call Trace:
enqueue_task_rt+0x291/0x360
__sched_setscheduler+0x581/0x9d0
_sched_setscheduler+0x63/0xa0
do_sched_setscheduler+0xa0/0x150
__x64_sys_sched_setscheduler+0x1a/0x30
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xae
__sched_setscheduler() uses rt_effective_prio() to handle proper queuing
of priority boosted tasks that are setscheduled while being boosted.
rt_effective_prio() is however called twice per each
__sched_setscheduler() call: first directly by __sched_setscheduler()
before dequeuing the task and then by __setscheduler() to actually do
the priority change. If the priority of the pi_top_task is concurrently
being changed however, it might happen that the two calls return
different results. If, for example, the first call returned the same rt
priority the task was running at and the second one a fair priority, the
task won't be removed by the rt list (on_list still set) and then
enqueued in the fair runqueue. When eventually setscheduled back to rt
it will be seen as enqueued already and the WARNING/BUG be issued.
Fix this by calling rt_effective_prio() only once and then reusing the
return value. While at it refactor code as well for clarity. Concurrent
priority inheritance handling is still safe and will eventually converge
to a new state by following the inheritance chain(s).
Fixes: 0782e63bc6 ("sched: Handle priority boosted tasks proper in setscheduler()")
[squashed Peterz changes; added changelog]
Reported-by: Mark Simmons <msimmons@redhat.com>
Signed-off-by: Juri Lelli <juri.lelli@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20210803104501.38333-1-juri.lelli@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df51fe7ea1 upstream.
If we use "perf record" in an AMD Milan guest, dmesg reports a #GP
warning from an unchecked MSR access error on MSR_F15H_PERF_CTLx:
[] unchecked MSR access error: WRMSR to 0xc0010200 (tried to write 0x0000020000110076) at rIP: 0xffffffff8106ddb4 (native_write_msr+0x4/0x20)
[] Call Trace:
[] amd_pmu_disable_event+0x22/0x90
[] x86_pmu_stop+0x4c/0xa0
[] x86_pmu_del+0x3a/0x140
The AMD64_EVENTSEL_HOSTONLY bit is defined and used on the host,
while the guest perf driver should avoid such use.
Fixes: 1018faa6cf ("perf/x86/kvm: Fix Host-Only/Guest-Only counting with SVM disabled")
Signed-off-by: Like Xu <likexu@tencent.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Tested-by: Kim Phillips <kim.phillips@amd.com>
Tested-by: Liam Merwick <liam.merwick@oracle.com>
Link: https://lkml.kernel.org/r/20210802070850.35295-1-likexu@tencent.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8eee86317 upstream.
Sparse reports a compile time warning when dereferencing an
__iomem pointer:
drivers/soc/ixp4xx/ixp4xx-qmgr.c:149:37: warning: dereference of noderef expression
drivers/soc/ixp4xx/ixp4xx-qmgr.c:153:40: warning: dereference of noderef expression
drivers/soc/ixp4xx/ixp4xx-qmgr.c:154:40: warning: dereference of noderef expression
drivers/soc/ixp4xx/ixp4xx-qmgr.c:174:38: warning: dereference of noderef expression
drivers/soc/ixp4xx/ixp4xx-qmgr.c:174:44: warning: dereference of noderef expression
Use __raw_readl() here for consistency with the rest of the file.
This should really get converted to some proper accessor, as the
__raw functions are not meant to be used in drivers, but the driver
has used these since the start, so for the moment, let's only fix
the warning.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: d4c9e9fc97 ("IXP42x: Add QMgr support for IXP425 rev. A0 processors.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce5a595744 upstream.
We currently only enforce BW floors for a subset of nodes in a path.
All BCMs that need updating are queued in the pre_aggregate/aggregate
phase. The first set() commits all queued BCMs and subsequent set()
calls short-circuit without committing anything. Since the floor BW
isn't set in sum_avg/max_peak until set(), then some BCMs are committed
before their associated nodes reflect the floor.
Set the floor as each node is being aggregated. This ensures that all
all relevant floors are set before the BCMs are committed.
Fixes: 266cd33b59 ("interconnect: qcom: Ensure that the floor bandwidth value is enforced")
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
Link: https://lore.kernel.org/r/20210721175432.2119-4-mdtipton@codeaurora.org
[georgi: Removed unused variable]
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8861452b20 upstream.
When compile-testing with 64-bit resource_size_t, gcc reports an invalid
printk format string:
In file included from include/linux/dma-mapping.h:7,
from drivers/soc/ixp4xx/ixp4xx-npe.c:15:
drivers/soc/ixp4xx/ixp4xx-npe.c: In function 'ixp4xx_npe_probe':
drivers/soc/ixp4xx/ixp4xx-npe.c:694:18: error: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'resource_size_t' {aka 'long long unsigned int'} [-Werror=format=]
dev_info(dev, "NPE%d at 0x%08x-0x%08x not available\n",
Use the special %pR format string to print the resources.
Fixes: 0b458d7b10 ("soc: ixp4xx: npe: Pass addresses as resources")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d5aaad6f83 upstream.
Take a signed 'long' instead of an 'unsigned long' for the number of
pages to add/subtract to the total number of pages used by the MMU. This
fixes a zero-extension bug on 32-bit kernels that effectively corrupts
the per-cpu counter used by the shrinker.
Per-cpu counters take a signed 64-bit value on both 32-bit and 64-bit
kernels, whereas kvm_mod_used_mmu_pages() takes an unsigned long and thus
an unsigned 32-bit value on 32-bit kernels. As a result, the value used
to adjust the per-cpu counter is zero-extended (unsigned -> signed), not
sign-extended (signed -> signed), and so KVM's intended -1 gets morphed to
4294967295 and effectively corrupts the counter.
This was found by a staggering amount of sheer dumb luck when running
kvm-unit-tests on a 32-bit KVM build. The shrinker just happened to kick
in while running tests and do_shrink_slab() logged an error about trying
to free a negative number of objects. The truly lucky part is that the
kernel just happened to be a slightly stale build, as the shrinker no
longer yells about negative objects as of commit 18bb473e50 ("mm:
vmscan: shrink deferred objects proportional to priority").
vmscan: shrink_slab: mmu_shrink_scan+0x0/0x210 [kvm] negative objects to delete nr=-858993460
Fixes: bc8a3d8925 ("kvm: mmu: Fix overflow on kvm mmu page limit calculation")
Cc: stable@vger.kernel.org
Cc: Ben Gardon <bgardon@google.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210804214609.1096003-1-seanjc@google.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85cd39af14 upstream.
KVM creates a debugfs directory for each VM in order to store statistics
about the virtual machine. The directory name is built from the process
pid and a VM fd. While generally unique, it is possible to keep a
file descriptor alive in a way that causes duplicate directories, which
manifests as these messages:
[ 471.846235] debugfs: Directory '20245-4' with parent 'kvm' already present!
Even though this should not happen in practice, it is more or less
expected in the case of KVM for testcases that call KVM_CREATE_VM and
close the resulting file descriptor repeatedly and in parallel.
When this happens, debugfs_create_dir() returns an error but
kvm_create_vm_debugfs() goes on to allocate stat data structs which are
later leaked. The slow memory leak was spotted by syzkaller, where it
caused OOM reports.
Since the issue only affects debugfs, do a lookup before calling
debugfs_create_dir, so that the message is downgraded and rate-limited.
While at it, ensure kvm->debugfs_dentry is NULL rather than an error
if it is not created. This fixes kvm_destroy_vm_debugfs, which was not
checking IS_ERR_OR_NULL correctly.
Cc: stable@vger.kernel.org
Fixes: 536a6f88c4 ("KVM: Create debugfs dir and stat files for each VM")
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fa7a549d32 upstream.
Once an exception has been injected, any side effects related to
the exception (such as setting CR2 or DR6) have been taked place.
Therefore, once KVM sets the VM-entry interruption information
field or the AMD EVENTINJ field, the next VM-entry must deliver that
exception.
Pending interrupts are processed after injected exceptions, so
in theory it would not be a problem to use KVM_INTERRUPT when
an injected exception is present. However, DOSEMU is using
run->ready_for_interrupt_injection to detect interrupt windows
and then using KVM_SET_SREGS/KVM_SET_REGS to inject the
interrupt manually. For this to work, the interrupt window
must be delayed after the completion of the previous event
injection.
Cc: stable@vger.kernel.org
Reported-by: Stas Sergeev <stsp2@yandex.ru>
Tested-by: Stas Sergeev <stsp2@yandex.ru>
Fixes: 71cc849b70 ("KVM: x86: Fix split-irqchip vs interrupt injection window request")
Reviewed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec7099fdea upstream.
This reverts commit 3d5bfbd971.
When booting with threadirqs, it causes a splat
WARNING: CPU: 0 PID: 29 at kernel/irq/handle.c:159 __handle_irq_event_percpu+0x1ec/0x27c
irq 66 handler irq_default_primary_handler+0x0/0x1c enabled interrupts
That splat later went away with commit 81e2073c17 ("genirq: Disable
interrupts for force threaded handlers"), which got backported to
-stable. However, when running an -rt kernel, the splat still
exists. Moreover, quoting Thomas Gleixner [1]
But 3d5bfbd971 ("gpio: mpc8xxx: change the gpio interrupt flags.")
has nothing to do with that:
"Delete the interrupt IRQF_NO_THREAD flags in order to gpio interrupts
can be threaded to allow high-priority processes to preempt."
This changelog is blatantly wrong. In mainline forced irq threads
have always been invoked with softirqs disabled, which obviously
makes them non-preemptible.
So the patch didn't even do what its commit log said.
[1] https://lore.kernel.org/lkml/871r8zey88.ffs@nanos.tec.linutronix.de/
Cc: stable@vger.kernel.org # v5.9+
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6d90e9f22 upstream.
Make the RNG on AM3 GP only.
Based on this patch from TI v5.4 tree which is based on hwmod data
which are now removed:
| ARM: AM43xx: hwmod: Move RNG to a GP only links table
|
| On non-GP devices the RNG is controlled by the secure-side software,
| like in DRA7xx hwmod we should not control this IP when we are not
| a GP device.
|
| Signed-off-by: Andrew F. Davis <afd@ti.com>
Cc: stable@vger.kernel.org # v5.10+
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e39cdacf2f upstream.
During the driver loading process, the 'dev' field was not assigned, but
the 'dev' field was referenced in the subsequent 'i82092aa_set_mem_map'
function.
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
CC: <stable@vger.kernel.org>
[linux@dominikbrodowski.net: shorten commit message, add Cc to stable]
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e9505064f upstream.
The attribute-translator has to take in mind maxtype, that is
xfrm_link::nla_max. When it is set, attributes are not of xfrm_attr_type_t.
Currently, they can be only XFRMA_SPD_MAX (message XFRM_MSG_NEWSPDINFO),
their UABI is the same for 64/32-bit, so just copy them.
Thanks to YueHaibing for reporting this:
In xfrm_user_rcv_msg_compat() if maxtype is not zero and less than
XFRMA_MAX, nlmsg_parse_deprecated() do not initialize attrs array fully.
xfrm_xlate32() will access uninit 'attrs[i]' while iterating all attrs
array.
KASAN: probably user-memory-access in range [0x0000000041b58ab0-0x0000000041b58ab7]
CPU: 0 PID: 15799 Comm: syz-executor.2 Tainted: G W 5.14.0-rc1-syzkaller #0
RIP: 0010:nla_type include/net/netlink.h:1130 [inline]
RIP: 0010:xfrm_xlate32_attr net/xfrm/xfrm_compat.c:410 [inline]
RIP: 0010:xfrm_xlate32 net/xfrm/xfrm_compat.c:532 [inline]
RIP: 0010:xfrm_user_rcv_msg_compat+0x5e5/0x1070 net/xfrm/xfrm_compat.c:577
[...]
Call Trace:
xfrm_user_rcv_msg+0x556/0x8b0 net/xfrm/xfrm_user.c:2774
netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2504
xfrm_netlink_rcv+0x6b/0x90 net/xfrm/xfrm_user.c:2824
netlink_unicast_kernel net/netlink/af_netlink.c:1314 [inline]
netlink_unicast+0x533/0x7d0 net/netlink/af_netlink.c:1340
netlink_sendmsg+0x86d/0xdb0 net/netlink/af_netlink.c:1929
sock_sendmsg_nosec net/socket.c:702 [inline]
Fixes: 5106f4a8ac ("xfrm/compat: Add 32=>64-bit messages translator")
Cc: <stable@kernel.org>
Reported-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2580d3f400 upstream.
xfrm_bydst_resize() calls synchronize_rcu() while holding
hash_resize_mutex. But then on PREEMPT_RT configurations,
xfrm_policy_lookup_bytype() may acquire that mutex while running in an
RCU read side critical section. This results in a deadlock.
In fact the scope of hash_resize_mutex is way beyond the purpose of
xfrm_policy_lookup_bytype() to just fetch a coherent and stable policy
for a given destination/direction, along with other details.
The lower level net->xfrm.xfrm_policy_lock, which among other things
protects per destination/direction references to policy entries, is
enough to serialize and benefit from priority inheritance against the
write side. As a bonus, it makes it officially a per network namespace
synchronization business where a policy table resize on namespace A
shouldn't block a policy lookup on namespace B.
Fixes: 77cc278f7b (xfrm: policy: Use sequence counters with associated lock)
Cc: stable@vger.kernel.org
Cc: Ahmed S. Darwish <a.darwish@linutronix.de>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Varad Gautam <varad.gautam@suse.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb7262b295 upstream.
syzbot reported KCSAN data races vs. timer_base::timer_running being set to
NULL without holding base::lock in expire_timers().
This looks innocent and most reads are clearly not problematic, but
Frederic identified an issue which is:
int data = 0;
void timer_func(struct timer_list *t)
{
data = 1;
}
CPU 0 CPU 1
------------------------------ --------------------------
base = lock_timer_base(timer, &flags); raw_spin_unlock(&base->lock);
if (base->running_timer != timer) call_timer_fn(timer, fn, baseclk);
ret = detach_if_pending(timer, base, true); base->running_timer = NULL;
raw_spin_unlock_irqrestore(&base->lock, flags); raw_spin_lock(&base->lock);
x = data;
If the timer has previously executed on CPU 1 and then CPU 0 can observe
base->running_timer == NULL and returns, assuming the timer has completed,
but it's not guaranteed on all architectures. The comment for
del_timer_sync() makes that guarantee. Moving the assignment under
base->lock prevents this.
For non-RT kernel it's performance wise completely irrelevant whether the
store happens before or after taking the lock. For an RT kernel moving the
store under the lock requires an extra unlock/lock pair in the case that
there is a waiter for the timer, but that's not the end of the world.
Reported-by: syzbot+aa7c2385d46c5eba0b89@syzkaller.appspotmail.com
Reported-by: syzbot+abea4558531bae1ba9fe@syzkaller.appspotmail.com
Fixes: 030dcdd197 ("timers: Prepare support for PREEMPT_RT")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/87lfea7gw8.fsf@nanos.tec.linutronix.de
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec6446d530 upstream.
The performance reporting driver added cpu hotplug
feature but it didn't add pmu migration call in cpu
offline function.
This can create an issue incase the current designated
cpu being used to collect fme pmu data got offline,
as based on current code we are not migrating fme pmu to
new target cpu. Because of that perf will still try to
fetch data from that offline cpu and hence we will not
get counter data.
Patch fixed this issue by adding pmu_migrate_context call
in fme_perf_offline_cpu function.
Fixes: 724142f8c4 ("fpga: dfl: fme: add performance reporting support")
Cc: stable@vger.kernel.org
Tested-by: Xu Yilun <yilun.xu@intel.com>
Acked-by: Wu Hao <hao.wu@intel.com>
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 341abd693d upstream.
This attempts to fix a bug found with a serial port card which uses
an MCS9922 chip, one of the 4 models for which MSI-X interrupts are
currently supported. I don't possess such a card, and i'm not
experienced with the serial subsystem, so this patch is based on what
i think i found as a likely reason for failure, based on walking the
user who actually owns the card through some diagnostic.
The user who reported the problem finds the following in his dmesg
output for the relevant ttyS4 and ttyS5:
[ 0.580425] serial 0000:02:00.0: enabling device (0000 -> 0003)
[ 0.601448] 0000:02:00.0: ttyS4 at I/O 0x3010 (irq = 125, base_baud = 115200) is a ST16650V2
[ 0.603089] serial 0000:02:00.1: enabling device (0000 -> 0003)
[ 0.624119] 0000:02:00.1: ttyS5 at I/O 0x3000 (irq = 126, base_baud = 115200) is a ST16650V2
...
[ 6.323784] genirq: Flags mismatch irq 128. 00000080 (ttyS5) vs. 00000000 (xhci_hcd)
[ 6.324128] genirq: Flags mismatch irq 128. 00000080 (ttyS5) vs. 00000000 (xhci_hcd)
...
Output of setserial -a:
/dev/ttyS4, Line 4, UART: 16650V2, Port: 0x3010, IRQ: 127
Baud_base: 115200, close_delay: 50, divisor: 0
closing_wait: 3000
Flags: spd_normal skip_test
This suggests to me that the serial driver wants to register and share a
MSI/MSI-X irq 128 with the xhci_hcd driver, whereas the xhci driver does
not want to share the irq, as flags 0x00000080 (== IRQF_SHARED) from the
serial port driver means to share the irq, and this mismatch ends in some
failed irq init?
With this setup, data reception works very unreliable, with dropped data,
already at a transmission rate of only a 16 Bytes chunk every 1/120th of
a second, ie. 1920 Bytes/sec, presumably due to rx fifo overflow due to
mishandled or not used at all rx irq's?
See full discussion thread with attempted diagnosis at:
https://psychtoolbox.discourse.group/t/issues-with-iscan-serial-port-recording/3886
Disabling the use of MSI interrupts for the serial port pci card did
fix the reliability problems. The user executed the following sequence
of commands to achieve this:
echo 0000:02:00.0 | sudo tee /sys/bus/pci/drivers/serial/unbind
echo 0000:02:00.1 | sudo tee /sys/bus/pci/drivers/serial/unbind
echo 0 | sudo tee /sys/bus/pci/devices/0000:02:00.0/msi_bus
echo 0 | sudo tee /sys/bus/pci/devices/0000:02:00.1/msi_bus
echo 0000:02:00.0 | sudo tee /sys/bus/pci/drivers/serial/bind
echo 0000:02:00.1 | sudo tee /sys/bus/pci/drivers/serial/bind
This resulted in the following log output:
[ 82.179021] pci 0000:02:00.0: MSI/MSI-X disallowed for future drivers
[ 87.003031] pci 0000:02:00.1: MSI/MSI-X disallowed for future drivers
[ 98.537010] 0000:02:00.0: ttyS4 at I/O 0x3010 (irq = 17, base_baud = 115200) is a ST16650V2
[ 103.648124] 0000:02:00.1: ttyS5 at I/O 0x3000 (irq = 18, base_baud = 115200) is a ST16650V2
This patch attempts to fix the problem by disabling irq sharing when
using MSI irq's. Note that all i know for sure is that disabling MSI
irq's fixed the problem for the user, so this patch could be wrong and
is untested. Please review with caution, keeping this in mind.
Fixes: 8428413b1d ("serial: 8250_pci: Implement MSI(-X) support")
Cc: Ralf Ramsauer <ralf.ramsauer@oth-regensburg.de>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Link: https://lore.kernel.org/r/20210729043306.18528-1-mario.kleiner.de@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a936d6c3d upstream.
Correct big-endian accesses to the CBUS UART, a Malta on-board discrete
TI16C550C part wired directly to the system controller's device bus, and
do not use byte swapping with the 32-bit accesses to the device.
The CBUS is used for devices such as the boot flash memory needed early
on in system bootstrap even before PCI has been initialised. Therefore
it uses the system controller's device bus, which follows the endianness
set with the CPU, which means no byte-swapping is ever required for data
accesses to CBUS, unlike with PCI.
The CBUS UART uses the UPIO_MEM32 access method, that is the `readl' and
`writel' MMIO accessors, which on the MIPS platform imply byte-swapping
with PCI systems. Consequently the wrong byte lane is accessed with the
big-endian configuration and the UART is not correctly accessed.
As it happens the UPIO_MEM32BE access method makes use of the `ioread32'
and `iowrite32' MMIO accessors, which still use `readl' and `writel'
respectively, however they byte-swap data passed, effectively cancelling
swapping done with the accessors themselves and making it suitable for
the CBUS UART.
Make the CBUS UART switch between UPIO_MEM32 and UPIO_MEM32BE then,
based on the endianness selected. With this change in place the device
is correctly recognised with big-endian Malta at boot, along with the
Super I/O devices behind PCI:
Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled
printk: console [ttyS0] disabled
serial8250.0: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
printk: console [ttyS0] enabled
printk: bootconsole [uart8250] disabled
serial8250.0: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A
serial8250.0: ttyS2 at MMIO 0x1f000900 (irq = 20, base_baud = 230400) is a 16550A
Fixes: e7c4782f92 ("[MIPS] Put an end to <asm/serial.h>'s long and annyoing existence")
Cc: stable@vger.kernel.org # v2.6.23+
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260524430.37803@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5227c5109 upstream.
Make sure only actual 8 bits of the IIR register are used in determining
the port type in `autoconfig'.
The `serial_in' port accessor returns the `unsigned int' type, meaning
that with UPIO_AU, UPIO_MEM16, UPIO_MEM32, and UPIO_MEM32BE access types
more than 8 bits of data are returned, of which the high order bits will
often come from bus lines that are left floating in the data phase. For
example with the MIPS Malta board's CBUS UART, where the registers are
aligned on 8-byte boundaries and which uses 32-bit accesses, data as
follows is returned:
YAMON> dump -32 0xbf000900 0x40
BF000900: 1F000942 1F000942 1F000900 1F000900 ...B...B........
BF000910: 1F000901 1F000901 1F000900 1F000900 ................
BF000920: 1F000900 1F000900 1F000960 1F000960 ...........`...`
BF000930: 1F000900 1F000900 1F0009FF 1F0009FF ................
YAMON>
Evidently high-order 24 bits return values previously driven in the
address phase (the 3 highest order address bits used with the command
above are masked out in the simple virtual address mapping used here and
come out at zeros on the external bus), a common scenario with bus lines
left floating, due to bus capacitance.
Consequently when the value of IIR, mapped at 0x1f000910, is retrieved
in `autoconfig', it comes out at 0x1f0009c1 and when it is right-shifted
by 6 and then assigned to 8-bit `scratch' variable, the value calculated
is 0x27, not one of 0, 1, 2, 3 expected in port type determination.
Fix the issue then, by assigning the value returned from `serial_in' to
`scratch' first, which masks out 24 high-order bits retrieved, and only
then right-shift the resulting 8-bit data quantity, producing the value
of 3 in this case, as expected. Fix the same issue in `serial_dl_read'.
The problem first appeared with Linux 2.6.9-rc3 which predates our repo
history, but the origin could be identified with the old MIPS/Linux repo
also at: <git://git.kernel.org/pub/scm/linux/kernel/git/ralf/linux.git>
as commit e0d2356c0777 ("Merge with Linux 2.6.9-rc3."), where code in
`serial_in' was updated with this case:
+ case UPIO_MEM32:
+ return readl(up->port.membase + offset);
+
which made it produce results outside the unsigned 8-bit range for the
first time, though obviously it is system dependent what actual values
appear in the high order bits retrieved and it may well have been zeros
in the relevant positions with the system the change originally was
intended for. It is at that point that code in `autoconf' should have
been updated accordingly, but clearly it was overlooked.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org # v2.6.12+
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260516220.37803@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c4a509d38 upstream.
Fix uart corruption issue when rx power off.
Add spin lock in mtk8250_dma_rx_complete function in APDMA mode.
when uart is used as a communication port with external device(GPS).
when external device(GPS) power off, the power of rx pin is also from
1.8v to 0v. Even if there is not any data in rx. But uart rx pin can
capture the data "0".
If uart don't receive any data in specified cycle, uart will generates
BI(Break interrupt) interrupt.
If external device(GPS) power off, we found that BI interrupt appeared
continuously and very frequently.
When uart interrupt type is BI, uart IRQ handler(8250 framwork
API:serial8250_handle_irq) will push data to tty buffer.
mtk8250_dma_rx_complete is a task of mtk_uart_apdma_rx_handler.
mtk8250_dma_rx_complete priority is lower than uart irq
handler(serial8250_handle_irq).
if we are in process of mtk8250_dma_rx_complete, uart appear BI
interrupt:1)serial8250_handle_irq will priority execution.2)it may cause
write tty buffer conflict in mtk8250_dma_rx_complete.
So the spin lock protect the rx receive data process is not break.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210729084640.17613-2-zhiyong.tao@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 877ba3f729 upstream.
Commit b5776e7524 ("ext4: fix potential htree index checksum
corruption) removed a required restart when multiple levels of index
nodes need to be split. Fix this to avoid directory htree corruptions
when using the large_dir feature.
Cc: stable@kernel.org # v5.11
Cc: Благодаренко Артём <artem.blagodarenko@gmail.com>
Fixes: b5776e7524 ("ext4: fix potential htree index checksum corruption)
Reported-by: Denis <denis@voxelsoft.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 76f22c93b2 upstream.
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Control transfers without a data stage are treated as OUT requests by
the USB stack and should be using usb_sndctrlpipe(). Failing to do so
will now trigger a warning.
The driver uses a zero-length i2c-read request for type detection so
update the control-request code to use usb_sndctrlpipe() in this case.
Note that actually trying to read the i2c register in question does not
work as the register might not exist (e.g. depending on the demodulator)
as reported by Eero Lehtinen <debiangamer2@gmail.com>.
Reported-by: syzbot+faf11bbadc5a372564da@syzkaller.appspotmail.com
Reported-by: Eero Lehtinen <debiangamer2@gmail.com>
Tested-by: Eero Lehtinen <debiangamer2@gmail.com>
Fixes: d0f232e823 ("[media] rtl28xxu: add heuristic to detect chip type")
Cc: stable@vger.kernel.org # 4.0
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4d1014c181 upstream.
dma_range_map is freed to early, which might cause an oops when
a driver probe fails.
Call trace:
is_free_buddy_page+0xe4/0x1d4
__free_pages+0x2c/0x88
dma_free_contiguous+0x64/0x80
dma_direct_free+0x38/0xb4
dma_free_attrs+0x88/0xa0
dmam_release+0x28/0x34
release_nodes+0x78/0x8c
devres_release_all+0xa8/0x110
really_probe+0x118/0x2d0
__driver_probe_device+0xc8/0xe0
driver_probe_device+0x54/0xec
__driver_attach+0xe0/0xf0
bus_for_each_dev+0x7c/0xc8
driver_attach+0x30/0x3c
bus_add_driver+0x17c/0x1c4
driver_register+0xc0/0xf8
__platform_driver_register+0x34/0x40
...
This issue is introduced by commit d0243bbd5d ("drivers core:
Free dma_range_map when driver probe failed"). It frees
dma_range_map before the call to devres_release_all, which is too
early. The solution is to free dma_range_map only after
devres_release_all.
Fixes: d0243bbd5d ("drivers core: Free dma_range_map when driver probe failed")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Filip Schauer <filip@mg6.at>
Link: https://lore.kernel.org/r/20210727112311.GA7645@DESKTOP-E8BN1B0.localdomain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9e6aa51b2 upstream.
There was strange error handling logic in case of fw load failure. For
some reason fw loader callback was doing clean up stuff when fw is not
available. I don't see any reason behind doing this. Since this driver
doesn't have EEPROM firmware let's just disconnect it in case of fw load
failure. Doing clean up stuff in 2 different place which can run
concurently is not good idea and syzbot found 2 bugs related to this
strange approach.
So, in this pacth I deleted all clean up code from fw callback and made
a call to device_release_driver() under device_lock(parent) in case of fw
load failure. This approach is more generic and it defend driver from UAF
bugs, since all clean up code is moved to one place.
Fixes: e02a3b9458 ("staging: rtl8712: fix memory leak in rtl871x_load_fw_cb")
Fixes: 8c213fa591 ("staging: r8712u: Use asynchronous firmware loading")
Cc: stable <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+5872a520e0ce0a7c7230@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+cc699626e48a6ebaf295@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/d49ecc56e97c4df181d7bd4d240b031f315eacc3.1626895918.git.paskripkin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dfb703ad2a upstream.
dma-buf backed shared memory cannot be reliably freed and unregistered
during a kexec operation even when tee_shm_free() is called on the shm
from a .shutdown hook. The problem occurs because dma_buf_put() calls
fput() which then uses task_work_add(), with the TWA_RESUME parameter,
to queue tee_shm_release() to be called before the current task returns
to user mode. However, the current task never returns to user mode
before the kexec completes so the memory is never freed nor
unregistered.
Use tee_shm_alloc_kernel_buf() to avoid dma-buf backed shared memory
allocation so that tee_shm_free() can directly call tee_shm_release().
This will ensure that the shm can be freed and unregistered during a
kexec operation.
Fixes: 09e574831b ("tpm/tpm_ftpm_tee: A driver for firmware TPM running inside TEE")
Fixes: 1760eb689e ("tpm/tpm_ftpm_tee: add shutdown call back")
Cc: stable@vger.kernel.org
Signed-off-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Acked-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit adf752af45 upstream.
Fix a hung task issue, seen when booting the kdump kernel, that is
caused by all of the secure world threads being in a permanent suspended
state:
INFO: task swapper/0:1 blocked for more than 120 seconds.
Not tainted 5.4.83 #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
swapper/0 D 0 1 0 0x00000028
Call trace:
__switch_to+0xc8/0x118
__schedule+0x2e0/0x700
schedule+0x38/0xb8
schedule_timeout+0x258/0x388
wait_for_completion+0x16c/0x4b8
optee_cq_wait_for_completion+0x28/0xa8
optee_disable_shm_cache+0xb8/0xf8
optee_probe+0x560/0x61c
platform_drv_probe+0x58/0xa8
really_probe+0xe0/0x338
driver_probe_device+0x5c/0xf0
device_driver_attach+0x74/0x80
__driver_attach+0x64/0xe0
bus_for_each_dev+0x84/0xd8
driver_attach+0x30/0x40
bus_add_driver+0x188/0x1e8
driver_register+0x64/0x110
__platform_driver_register+0x54/0x60
optee_driver_init+0x20/0x28
do_one_initcall+0x54/0x24c
kernel_init_freeable+0x1e8/0x2c0
kernel_init+0x18/0x118
ret_from_fork+0x10/0x18
The invoke_fn hook returned OPTEE_SMC_RETURN_ETHREAD_LIMIT, indicating
that the secure world threads were all in a suspended state at the time
of the kernel crash. This intermittently prevented the kdump kernel from
booting, resulting in a failure to collect the kernel dump.
Make kernel dump collection more reliable on systems utilizing OP-TEE by
refusing to load the driver under the kdump kernel.
Cc: stable@vger.kernel.org
Signed-off-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5c10dd04b upstream.
The shm cache could contain invalid addresses if
optee_disable_shm_cache() was not called from the .shutdown hook of the
previous kernel before a kexec. These addresses could be unmapped or
they could point to mapped but unintended locations in memory.
Clear the shared memory cache, while being careful to not translate the
addresses returned from OPTEE_SMC_DISABLE_SHM_CACHE, during driver
initialization. Once all pre-cache shm objects are removed, proceed with
enabling the cache so that we know that we can handle cached shm objects
with confidence later in the .shutdown hook.
Cc: stable@vger.kernel.org
Signed-off-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c32706dac upstream.
When the function_graph tracer is in use, arch_stack_walk() may unwind
the stack incorrectly, erroneously reporting itself, missing the final
entry which is being traced, and reporting all traced entries between
these off-by-one from where they should be.
When ftrace hooks a function return, the original return address is
saved to the fgraph ret_stack, and the return address in the LR (or the
function's frame record) is replaced with `return_to_handler`.
When arm64's unwinder encounter frames returning to `return_to_handler`,
it finds the associated original return address from the fgraph ret
stack, assuming the most recent `ret_to_hander` entry on the stack
corresponds to the most recent entry in the fgraph ret stack, and so on.
When arch_stack_walk() is used to dump the current task's stack, it
starts from the caller of arch_stack_walk(). However, arch_stack_walk()
can be traced, and so may push an entry on to the fgraph ret stack,
leaving the fgraph ret stack offset by one from the expected position.
This can be seen when dumping the stack via /proc/self/stack, where
enabling the graph tracer results in an unexpected
`stack_trace_save_tsk` entry at the start of the trace, and `el0_svc`
missing form the end of the trace.
This patch fixes this by marking arch_stack_walk() as notrace, as we do
for all other functions on the path to ftrace_graph_get_ret_stack().
While a few helper functions are not marked notrace, their calls/returns
are balanced, and will have no observable effect when examining the
fgraph ret stack.
It is possible for an exeption boundary to cause a similar offset if the
return address of the interrupted context was in the LR. Fixing those
cases will require some more substantial rework, and is left for
subsequent patches.
Before:
| # cat /proc/self/stack
| [<0>] proc_pid_stack+0xc4/0x140
| [<0>] proc_single_show+0x6c/0x120
| [<0>] seq_read_iter+0x240/0x4e0
| [<0>] seq_read+0xe8/0x140
| [<0>] vfs_read+0xb8/0x1e4
| [<0>] ksys_read+0x74/0x100
| [<0>] __arm64_sys_read+0x28/0x3c
| [<0>] invoke_syscall+0x50/0x120
| [<0>] el0_svc_common.constprop.0+0xc4/0xd4
| [<0>] do_el0_svc+0x30/0x9c
| [<0>] el0_svc+0x2c/0x54
| [<0>] el0t_64_sync_handler+0x1a8/0x1b0
| [<0>] el0t_64_sync+0x198/0x19c
| # echo function_graph > /sys/kernel/tracing/current_tracer
| # cat /proc/self/stack
| [<0>] stack_trace_save_tsk+0xa4/0x110
| [<0>] proc_pid_stack+0xc4/0x140
| [<0>] proc_single_show+0x6c/0x120
| [<0>] seq_read_iter+0x240/0x4e0
| [<0>] seq_read+0xe8/0x140
| [<0>] vfs_read+0xb8/0x1e4
| [<0>] ksys_read+0x74/0x100
| [<0>] __arm64_sys_read+0x28/0x3c
| [<0>] invoke_syscall+0x50/0x120
| [<0>] el0_svc_common.constprop.0+0xc4/0xd4
| [<0>] do_el0_svc+0x30/0x9c
| [<0>] el0t_64_sync_handler+0x1a8/0x1b0
| [<0>] el0t_64_sync+0x198/0x19c
After:
| # cat /proc/self/stack
| [<0>] proc_pid_stack+0xc4/0x140
| [<0>] proc_single_show+0x6c/0x120
| [<0>] seq_read_iter+0x240/0x4e0
| [<0>] seq_read+0xe8/0x140
| [<0>] vfs_read+0xb8/0x1e4
| [<0>] ksys_read+0x74/0x100
| [<0>] __arm64_sys_read+0x28/0x3c
| [<0>] invoke_syscall+0x50/0x120
| [<0>] el0_svc_common.constprop.0+0xc4/0xd4
| [<0>] do_el0_svc+0x30/0x9c
| [<0>] el0_svc+0x2c/0x54
| [<0>] el0t_64_sync_handler+0x1a8/0x1b0
| [<0>] el0t_64_sync+0x198/0x19c
| # echo function_graph > /sys/kernel/tracing/current_tracer
| # cat /proc/self/stack
| [<0>] proc_pid_stack+0xc4/0x140
| [<0>] proc_single_show+0x6c/0x120
| [<0>] seq_read_iter+0x240/0x4e0
| [<0>] seq_read+0xe8/0x140
| [<0>] vfs_read+0xb8/0x1e4
| [<0>] ksys_read+0x74/0x100
| [<0>] __arm64_sys_read+0x28/0x3c
| [<0>] invoke_syscall+0x50/0x120
| [<0>] el0_svc_common.constprop.0+0xc4/0xd4
| [<0>] do_el0_svc+0x30/0x9c
| [<0>] el0_svc+0x2c/0x54
| [<0>] el0t_64_sync_handler+0x1a8/0x1b0
| [<0>] el0t_64_sync+0x198/0x19c
Cc: <stable@vger.kernel.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Madhavan T. Venkataraman <madvenka@linux.microsoft.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Will Deacon <will@kernel.org>
Reviwed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210802164845.45506-3-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 231264d692 upstream.
On a 1->0->1 callbacks transition, there is an issue with the new
callback using the old callback's data.
Considering __DO_TRACE_CALL:
do { \
struct tracepoint_func *it_func_ptr; \
void *__data; \
it_func_ptr = \
rcu_dereference_raw((&__tracepoint_##name)->funcs); \
if (it_func_ptr) { \
__data = (it_func_ptr)->data; \
----> [ delayed here on one CPU (e.g. vcpu preempted by the host) ]
static_call(tp_func_##name)(__data, args); \
} \
} while (0)
It has loaded the tp->funcs of the old callback, so it will try to use the old
data. This can be fixed by adding a RCU sync anywhere in the 1->0->1
transition chain.
On a N->2->1 transition, we need an rcu-sync because you may have a
sequence of 3->2->1 (or 1->2->1) where the element 0 data is unchanged
between 2->1, but was changed from 3->2 (or from 1->2), which may be
observed by the static call. This can be fixed by adding an
unconditional RCU sync in transition 2->1.
Note, this fixes a correctness issue at the cost of adding a tremendous
performance regression to the disabling of tracepoints.
Before this commit:
# trace-cmd start -e all
# time trace-cmd start -p nop
real 0m0.778s
user 0m0.000s
sys 0m0.061s
After this commit:
# trace-cmd start -e all
# time trace-cmd start -p nop
real 0m10.593s
user 0m0.017s
sys 0m0.259s
A follow up fix will introduce a more lightweight scheme based on RCU
get_state and cond_sync, that will return the performance back to what it
was. As both this change and the lightweight versions are complex on their
own, for bisecting any issues that this may cause, they are kept as two
separate changes.
Link: https://lkml.kernel.org/r/20210805132717.23813-3-mathieu.desnoyers@efficios.com
Link: https://lore.kernel.org/io-uring/4ebea8f0-58c9-e571-fd30-0ce4f6f09c70@samba.org/
Cc: stable@vger.kernel.org
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: "Paul E. McKenney" <paulmck@kernel.org>
Cc: Stefan Metzmacher <metze@samba.org>
Fixes: d25e37d89d ("tracepoint: Optimize using static_call()")
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff41c28c4b upstream.
The event_trace_add_tracer() can fail. In this case, it leads to a crash
in start_creating with below call stack. Handle the error scenario
properly in trace_array_create_dir.
Call trace:
down_write+0x7c/0x204
start_creating.25017+0x6c/0x194
tracefs_create_file+0xc4/0x2b4
init_tracer_tracefs+0x5c/0x940
trace_array_create_dir+0x58/0xb4
trace_array_create+0x1bc/0x2b8
trace_array_get_by_name+0xdc/0x18c
Link: https://lkml.kernel.org/r/1627651386-21315-1-git-send-email-kamaagra@codeaurora.org
Cc: stable@vger.kernel.org
Fixes: 4114fbfd02 ("tracing: Enable creating new instance early boot")
Signed-off-by: Kamal Agrawal <kamaagra@codeaurora.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c05caa7ba upstream.
When working on my user space applications, I found a bug in the synthetic
event code where the automated synthetic event field was not matching the
event field calculation it was attached to. Looking deeper into it, it was
because the calculation hist_field was not given a size.
The synthetic event fields are matched to their hist_fields either by
having the field have an identical string type, or if that does not match,
then the size and signed values are used to match the fields.
The problem arose when I tried to match a calculation where the fields
were "unsigned int". My tool created a synthetic event of type "u32". But
it failed to match. The string was:
diff=field1-field2:onmatch(event).trace(synth,$diff)
Adding debugging into the kernel, I found that the size of "diff" was 0.
And since it was given "unsigned int" as a type, the histogram fallback
code used size and signed. The signed matched, but the size of u32 (4) did
not match zero, and the event failed to be created.
This can be worse if the field you want to match is not one of the
acceptable fields for a synthetic event. As event fields can have any type
that is supported in Linux, this can cause an issue. For example, if a
type is an enum. Then there's no way to use that with any calculations.
Have the calculation field simply take on the size of what it is
calculating.
Link: https://lkml.kernel.org/r/20210730171951.59c7743f@oasis.local.home
Cc: Tom Zanussi <zanussi@kernel.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@vger.kernel.org
Fixes: 100719dcef ("tracing: Add simple expression support to hist triggers")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf88fef0b6 upstream.
The HNP work can be re-scheduled while it's still in-fly. This results in
re-initialization of the busy work, resetting the hrtimer's list node of
the work and crashing kernel with null dereference within kernel/timer
once work's timer is expired. It's very easy to trigger this problem by
re-plugging USB cable quickly. Initialize HNP work only once to fix this
trouble.
Unable to handle kernel NULL pointer dereference at virtual address 00000126)
...
PC is at __run_timers.part.0+0x150/0x228
LR is at __next_timer_interrupt+0x51/0x9c
...
(__run_timers.part.0) from [<c0187a2b>] (run_timer_softirq+0x2f/0x50)
(run_timer_softirq) from [<c01013ad>] (__do_softirq+0xd5/0x2f0)
(__do_softirq) from [<c012589b>] (irq_exit+0xab/0xb8)
(irq_exit) from [<c0170341>] (handle_domain_irq+0x45/0x60)
(handle_domain_irq) from [<c04c4a43>] (gic_handle_irq+0x6b/0x7c)
(gic_handle_irq) from [<c0100b65>] (__irq_svc+0x65/0xac)
Cc: stable@vger.kernel.org
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210717182134.30262-6-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit afcff6dc69 upstream.
The USB HID standard declares mandatory support for GET_IDLE and SET_IDLE
requests for Boot Keyboard. Most hosts can handle their absence, but others
like some old/strange UEFIs and BIOSes consider this a critical error
and refuse to work with f_hid.
This primitive implementation of saving and returning idle is sufficient
to meet the requirements of the standard and these devices.
Acked-by: Felipe Balbi <balbi@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Maxim Devaev <mdevaev@gmail.com>
Link: https://lore.kernel.org/r/20210721180351.129450-1-mdevaev@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cb10f68ad8 upstream.
If the device is already in the runtime suspended state, any call to
the pullup routine will issue a runtime resume on the DWC3 core
device. If the USB gadget is disabling the pullup, then avoid having
to issue a runtime resume, as DWC3 gadget has already been
halted/stopped.
This fixes an issue where the following condition occurs:
usb_gadget_remove_driver()
-->usb_gadget_disconnect()
-->dwc3_gadget_pullup(0)
-->pm_runtime_get_sync() -> ret = 0
-->pm_runtime_put() [async]
-->usb_gadget_udc_stop()
-->dwc3_gadget_stop()
-->dwc->gadget_driver = NULL
...
dwc3_suspend_common()
-->dwc3_gadget_suspend()
-->DWC3 halt/stop routine skipped, driver_data == NULL
This leads to a situation where the DWC3 gadget is not properly
stopped, as the runtime resume would have re-enabled EP0 and event
interrupts, and since we avoided the DWC3 gadget suspend, these
resources were never disabled.
Fixes: 77adb8bdf4 ("usb: dwc3: gadget: Allow runtime suspend if UDC unbinded")
Cc: stable <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1628058245-30692-1-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66291b6adb upstream.
The change to restore the autosuspend from the disabled state uses a
wrong check: namely, it should have been the exact comparison of the
quirk_type instead of the bitwise and (&). Otherwise it matches
wrongly with the other quirk types.
Although re-enabling the autosuspend for the already enabled device
shouldn't matter much, it's better to fix the unbalanced call.
Fixes: 9799110825 ("ALSA: usb-audio: Disable USB autosuspend properly in setup_disable_autosuspend()")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/s5hr1flh9ov.wl-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 75d95e2e39 upstream.
This use-after-free happens when a fw_priv object has been freed but
hasn't been removed from the pending list (pending_fw_head). The next
time fw_load_sysfs_fallback tries to insert into the list, it ends up
accessing the pending_list member of the previously freed fw_priv.
The root cause here is that all code paths that abort the fw load
don't delete it from the pending list. For example:
_request_firmware()
-> fw_abort_batch_reqs()
-> fw_state_aborted()
To fix this, delete the fw_priv from the list in __fw_set_state() if
the new state is DONE or ABORTED. This way, all aborts will remove
the fw_priv from the list. Accordingly, remove calls to list_del_init
that were being made before calling fw_state_(aborted|done).
Also, in fw_load_sysfs_fallback, don't add the fw_priv to the pending
list if it is already aborted. Instead, just jump out and return early.
Fixes: bcfbd3523f ("firmware: fix a double abort case with fw_load_sysfs_fallback")
Cc: stable <stable@vger.kernel.org>
Reported-by: syzbot+de271708674e2093097b@syzkaller.appspotmail.com
Tested-by: syzbot+de271708674e2093097b@syzkaller.appspotmail.com
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Anirudh Rayabharam <mail@anirudhrb.com>
Link: https://lore.kernel.org/r/20210728085107.4141-3-mail@anirudhrb.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d6434e10b upstream.
The only motivation for using -EAGAIN in commit 0542ad88fb
("firmware loader: Fix _request_firmware_load() return val for fw load
abort") was to distinguish the error from -ENOMEM, and so there is no
real reason in keeping it. -EAGAIN is typically used to tell the
userspace to try something again and in this case re-using the sysfs
loading interface cannot be retried when a timeout happens, so the
return value is also bogus.
-ETIMEDOUT is received when the wait times out and returning that
is much more telling of what the reason for the failure was. So, just
propagate that instead of returning -EAGAIN.
Suggested-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Anirudh Rayabharam <mail@anirudhrb.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210728085107.4141-2-mail@anirudhrb.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c18e9baee upstream.
The chip supports high transfer rates, but with the small default buffers
(64 bytes read), some entire blocks are regularly lost. This typically
happens at 1.5 Mbps (which is the default speed on Rockchip devices) when
used as a console to access U-Boot where the output of the "help" command
misses many lines and where "printenv" mangles the environment.
The FTDI driver doesn't suffer at all from this. One difference is that
it uses 512 bytes rx buffers and 256 bytes tx buffers. Adopting these
values completely resolved the issue, even the output of "dmesg" is
reliable. I preferred to leave the Tx value unchanged as it is not
involved in this issue, while a change could increase the risk of
triggering the same issue with other devices having too small buffers.
I verified that it backports well (and works) at least to 5.4. It's of
low importance enough to be dropped where it doesn't trivially apply
anymore.
Cc: stable@vger.kernel.org
Signed-off-by: Willy Tarreau <w@1wt.eu>
Link: https://lore.kernel.org/r/20210724152739.18726-1-w@1wt.eu
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 30fad76ce4 upstream.
rcu: INFO: rcu_preempt self-detected stall on CPU
rcu: 1-...!: (2 ticks this GP) idle=d92/1/0x4000000000000000
softirq=25390/25392 fqs=3
(t=12164 jiffies g=31645 q=43226)
rcu: rcu_preempt kthread starved for 12162 jiffies! g31645 f0x0
RCU_GP_WAIT_FQS(5) ->state=0x0 ->cpu=0
rcu: Unless rcu_preempt kthread gets sufficient CPU time,
OOM is now expected behavior.
rcu: RCU grace-period kthread stack dump:
task:rcu_preempt state:R running task
...........
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: usb_submit_urb failed: -19
The function usbtmc_interrupt() resubmits urbs when the error status
of an urb is -EPROTO. In systems using the dummy_hcd usb controller
this can result in endless interrupt loops when the usbtmc device is
disconnected from the host system.
Since host controller drivers already try to recover from transmission
errors, there is no need to resubmit the urb or try other solutions
to repair the error situation.
In case of errors the INT pipe just stops to wait for further packets.
Fixes: dbf3e7f654 ("Implement an ioctl to support the USMTMC-USB488 READ_STATUS_BYTE operation")
Cc: stable@vger.kernel.org
Reported-by: syzbot+e2eae5639e7203360018@syzkaller.appspotmail.com
Signed-off-by: Qiang.zhang <qiang.zhang@windriver.com>
Acked-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Link: https://lore.kernel.org/r/20210723004334.458930-1-qiang.zhang@windriver.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e04480920d ]
syzbot is hitting might_sleep() warning at hci_sock_dev_event() due to
calling lock_sock() with rw spinlock held [1].
It seems that history of this locking problem is a trial and error.
Commit b40df5743e ("[PATCH] bluetooth: fix socket locking in
hci_sock_dev_event()") in 2.6.21-rc4 changed bh_lock_sock() to
lock_sock() as an attempt to fix lockdep warning.
Then, commit 4ce61d1c7a ("[BLUETOOTH]: Fix locking in
hci_sock_dev_event().") in 2.6.22-rc2 changed lock_sock() to
local_bh_disable() + bh_lock_sock_nested() as an attempt to fix the
sleep in atomic context warning.
Then, commit 4b5dd696f8 ("Bluetooth: Remove local_bh_disable() from
hci_sock.c") in 3.3-rc1 removed local_bh_disable().
Then, commit e305509e67 ("Bluetooth: use correct lock to prevent UAF
of hdev object") in 5.13-rc5 again changed bh_lock_sock_nested() to
lock_sock() as an attempt to fix CVE-2021-3573.
This difficulty comes from current implementation that
hci_sock_dev_event(HCI_DEV_UNREG) is responsible for dropping all
references from sockets because hci_unregister_dev() immediately
reclaims resources as soon as returning from
hci_sock_dev_event(HCI_DEV_UNREG).
But the history suggests that hci_sock_dev_event(HCI_DEV_UNREG) was not
doing what it should do.
Therefore, instead of trying to detach sockets from device, let's accept
not detaching sockets from device at hci_sock_dev_event(HCI_DEV_UNREG),
by moving actual cleanup of resources from hci_unregister_dev() to
hci_cleanup_dev() which is called by bt_host_release() when all
references to this unregistered device (which is a kobject) are gone.
Since hci_sock_dev_event(HCI_DEV_UNREG) no longer resets
hci_pi(sk)->hdev, we need to check whether this device was unregistered
and return an error based on HCI_UNREGISTER flag. There might be subtle
behavioral difference in "monitor the hdev" functionality; please report
if you found something went wrong due to this patch.
Link: https://syzkaller.appspot.com/bug?extid=a5df189917e79d5e59c9 [1]
Reported-by: syzbot <syzbot+a5df189917e79d5e59c9@syzkaller.appspotmail.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes: e305509e67 ("Bluetooth: use correct lock to prevent UAF of hdev object")
Acked-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d75d0eff6 ]
If queue is dying while iolatency_set_limit() is in progress,
blk_get_queue() won't increment the refcount of the queue. However,
blk_put_queue() will still decrement the refcount later, which will
cause the refcout to be unbalanced.
Thus error out in such case to fix the problem.
Fixes: 8c772a9bfc ("blk-iolatency: fix IO hang due to negative inflight counter")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20210805124645.543797-1-yukuai3@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 942e560a3d ]
Smatch says:
drivers/net/ethernet/neterion/vxge/vxge-main.c:3518 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev);
drivers/net/ethernet/neterion/vxge/vxge-main.c:3518 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev);
drivers/net/ethernet/neterion/vxge/vxge-main.c:3520 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev);
drivers/net/ethernet/neterion/vxge/vxge-main.c:3520 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev);
Since vdev pointer is netdev private data accessing it after free_netdev()
call can cause use-after-free bug. Fix it by moving free_netdev() call at
the end of the function
Fixes: 6cca200362 ("vxge: cleanup probe error paths")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44712965bf ]
Smatch says:
drivers/net/ethernet/freescale/fec_main.c:3994 fec_drv_remove() error: Using fep after free_{netdev,candev}(ndev);
drivers/net/ethernet/freescale/fec_main.c:3995 fec_drv_remove() error: Using fep after free_{netdev,candev}(ndev);
Since fep pointer is netdev private data, accessing it after free_netdev()
call can cause use-after-free bug. Fix it by moving free_netdev() call at
the end of the function
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: a31eda65ba ("net: fec: fix clock count mis-match")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af35fc3735 ]
Syzbot reported uninit value pegasus_probe(). The problem was in missing
error handling.
get_interrupt_interval() internally calls read_eprom_word() which can
fail in some cases. For example: failed to receive usb control message.
These cases should be handled to prevent uninit value bug, since
read_eprom_word() will not initialize passed stack variable in case of
internal failure.
Fail log:
BUG: KMSAN: uninit-value in get_interrupt_interval drivers/net/usb/pegasus.c:746 [inline]
BUG: KMSAN: uninit-value in pegasus_probe+0x10e7/0x4080 drivers/net/usb/pegasus.c:1152
CPU: 1 PID: 825 Comm: kworker/1:1 Not tainted 5.12.0-rc6-syzkaller #0
...
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:79 [inline]
dump_stack+0x24c/0x2e0 lib/dump_stack.c:120
kmsan_report+0xfb/0x1e0 mm/kmsan/kmsan_report.c:118
__msan_warning+0x5c/0xa0 mm/kmsan/kmsan_instr.c:197
get_interrupt_interval drivers/net/usb/pegasus.c:746 [inline]
pegasus_probe+0x10e7/0x4080 drivers/net/usb/pegasus.c:1152
....
Local variable ----data.i@pegasus_probe created at:
get_interrupt_interval drivers/net/usb/pegasus.c:1151 [inline]
pegasus_probe+0xe57/0x4080 drivers/net/usb/pegasus.c:1152
get_interrupt_interval drivers/net/usb/pegasus.c:1151 [inline]
pegasus_probe+0xe57/0x4080 drivers/net/usb/pegasus.c:1152
Reported-and-tested-by: syzbot+02c9f70f3afae308464a@syzkaller.appspotmail.com
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/20210804143005.439-1-paskripkin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb653827c7 ]
Set the error code if bnx2x_alloc_fw_stats_mem() fails. The current
code returns success.
Fixes: ad5afc8936 ("bnx2x: Separate VF and PF logic")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28bbbb9875 ]
When cross compiling a MIPS kernel on a BSD based HOSTCC leads
to errors like
SYNC include/config/auto.conf.cmd - due to: .config
egrep: empty (sub)expression
UPD include/config/kernel.release
HOSTCC scripts/dtc/dtc.o - due to target missing
It turns out that egrep uses this egrep pattern:
(|MINOR_|PATCHLEVEL_)
This is not valid syntax or gives undefined results according
to POSIX 9.5.3 ERE Grammar
https://pubs.opengroup.org/onlinepubs/9699919799/basedefs/V1_chap09.html
It seems to be silently accepted by the Linux egrep implementation
while a BSD host complains.
Such patterns can be replaced by a transformation like
"(|p1|p2)" -> "(p1|p2)?"
Fixes: 48c35b2d24 ("[MIPS] There is no __GNUC_MAJOR__")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06f5553e0f ]
According to comment in qdisc_alloc(), sch->seqlock's lockdep
class key should be set to qdisc_tx_busylock, due to possible
type error, sch->busylock's lockdep class key is set to
qdisc_tx_busylock, which is duplicated because sch->busylock's
lockdep class key is already set in qdisc_alloc().
So fix it by replacing sch->busylock with sch->seqlock.
Fixes: 96009c7d50 ("sched: replace __QDISC_STATE_RUNNING bit with a spin lock")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1a58c013a ]
In case of this switch we work with 32bit registers on top of 16bit
bus. Some registers (for example access to forwarding database) have
trigger bit on the first 16bit half of request and the result +
configuration of request in the second half. Without this patch, we would
trigger database operation and overwrite result in one run.
To make it work properly, we should do the second part of transfer
before the first one is done.
So far, this rule seems to work for all registers on this switch.
Fixes: ec6698c272 ("net: dsa: add support for Atheros AR9331 built-in switch")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20210803063746.3600-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4039146777 ]
The patch fixing the returned value of ip6_skb_dst_mtu (int -> unsigned
int) was rebased between its initial review and the version applied. In
the meantime fade56410c was applied, which added a new variable (int)
used as the returned value. This lead to a mismatch between the function
prototype and the variable used as the return value.
Fixes: 40fc3054b4 ("net: ipv6: fix return value of ip6_skb_dst_mtu")
Cc: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9fdc5d85a8 ]
Pauseframe control is set to symmetric mode by default on the NFP.
Pause frames can not be configured through ethtool now, but ethtool can
report the supported mode.
Fixes: 265aeb511b ("nfp: add support for .get_link_ksettings()")
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae954bbc45 ]
In commit 58acd10092 ("sctp: update active_key for asoc when old key is
being replaced"), sctp_auth_asoc_init_active_key() is called to update
the active_key right after the old key is deleted and before the new key
is added, and it caused that the active_key could be found with the key_id.
In Ying Xu's testing, the BUG_ON in sctp_auth_asoc_init_active_key() was
triggered:
[ ] kernel BUG at net/sctp/auth.c:416!
[ ] RIP: 0010:sctp_auth_asoc_init_active_key.part.8+0xe7/0xf0 [sctp]
[ ] Call Trace:
[ ] sctp_auth_set_key+0x16d/0x1b0 [sctp]
[ ] sctp_setsockopt.part.33+0x1ba9/0x2bd0 [sctp]
[ ] __sys_setsockopt+0xd6/0x1d0
[ ] __x64_sys_setsockopt+0x20/0x30
[ ] do_syscall_64+0x5b/0x1a0
So fix it by moving the active_key update after sh_keys is added.
Fixes: 58acd10092 ("sctp: update active_key for asoc when old key is being replaced")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b87f43537 ]
The tqmx86 MFD driver was passing IRQ 0 for "no IRQ" in the past. This
causes warnings with newer kernels.
Prepare the gpio-tqmx86 driver for the fixed MFD driver by handling a
missing IRQ properly.
Fixes: b868db94a6 ("gpio: tqmx86: Add GPIO from for this IO controller")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7fe74dfd41 ]
Replace pci_enable_device() with pcim_enable_device(),
pci_disable_device() and pci_release_regions() will be
called in release automatically.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5e63c7d38 ]
The logic for discerning between KSZ8051 and KSZ87XX PHYs is incorrect
such that the that KSZ87XX switch is not identified correctly.
ksz8051_ksz8795_match_phy_device() uses the parameter ksz_phy_id
to discriminate whether it was called from ksz8051_match_phy_device()
or from ksz8795_match_phy_device() but since PHY_ID_KSZ87XX is the
same value as PHY_ID_KSZ8051, this doesn't work.
Instead use a bool to discriminate the caller.
Without this patch, the KSZ8795 switch port identifies as:
ksz8795-switch spi3.1 ade1 (uninitialized): PHY [dsa-0.1:03] driver [Generic PHY]
With the patch, it identifies correctly:
ksz8795-switch spi3.1 ade1 (uninitialized): PHY [dsa-0.1:03] driver [Micrel KSZ87XX Switch]
Fixes: 8b95599c55 ("net: phy: micrel: Discern KSZ8051 and KSZ8795 PHYs")
Signed-off-by: Steve Bennett <steveb@workware.net.au>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47c2c0c231 ]
On SJA1105P/Q/R/S and SJA1110, the L2 Lookup Table entries contain a
maskable "inner/outer tag" bit which means:
- when set to 1: match single-outer and double tagged frames
- when set to 0: match untagged and single-inner tagged frames
- when masked off: match all frames regardless of the type of tag
This driver does not make any meaningful distinction between inner tags
(matches on TPID) and outer tags (matches on TPID2). In fact, all VLAN
table entries are installed as SJA1110_VLAN_D_TAG, which means that they
match on both inner and outer tags.
So it does not make sense that we install FDB entries with the IOTAG bit
set to 1.
In VLAN-unaware mode, we set both TPID and TPID2 to 0xdadb, so the
switch will see frames as outer-tagged or double-tagged (never inner).
So the FDB entries will match if IOTAG is set to 1.
In VLAN-aware mode, we set TPID to 0x8100 and TPID2 to 0x88a8. So the
switch will see untagged and 802.1Q-tagged packets as inner-tagged, and
802.1ad-tagged packets as outer-tagged. So untagged and 802.1Q-tagged
packets will not match FDB entries if IOTAG is set to 1, but 802.1ad
tagged packets will. Strange.
To fix this, simply mask off the IOTAG bit from FDB entries, and make
them match regardless of whether the VLAN tag is inner or outer.
Fixes: 1da7382134 ("net: dsa: sja1105: Add FDB operations for P/Q/R/S series")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 589918df93 ]
Similar but not quite the same with what was done in commit b11f0a4c0c
("net: dsa: sja1105: be stateless when installing FDB entries") for
SJA1105E/T, it is desirable to drop the priv->vlan_aware check and
simply go ahead and install FDB entries in the VLAN that was given by
the bridge.
As opposed to SJA1105E/T, in SJA1105P/Q/R/S and SJA1110, the FDB is a
maskable TCAM, and we are installing VLAN-unaware FDB entries with the
VLAN ID masked off. However, such FDB entries might completely obscure
VLAN-aware entries where the VLAN ID is included in the search mask,
because the switch looks up the FDB from left to right and picks the
first entry which results in a masked match. So it depends on whether
the bridge installs first the VLAN-unaware or the VLAN-aware FDB entries.
Anyway, if we had a VLAN-unaware FDB entry towards one set of DESTPORTS
and a VLAN-aware one towards other set of DESTPORTS, the result is that
the packets in VLAN-aware mode will be forwarded towards the DESTPORTS
specified by the VLAN-unaware entry.
To solve this, simply do not use the masked matching ability of the FDB
for VLAN ID, and always match precisely on it. In VLAN-unaware mode, we
configure the switch for shared VLAN learning, so the VLAN ID will be
ignored anyway during lookup, so it is redundant to mask it off in the
TCAM.
This patch conflicts with net-next commit 0fac6aa098 ("net: dsa: sja1105:
delete the best_effort_vlan_filtering mode") which changed this line:
if (priv->vlan_state != SJA1105_VLAN_UNAWARE) {
into:
if (priv->vlan_aware) {
When merging with net-next, the lines added by this patch should take
precedence in the conflict resolution (i.e. the "if" condition should be
deleted in both cases).
Fixes: 1da7382134 ("net: dsa: sja1105: Add FDB operations for P/Q/R/S series")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c5fc159e0 ]
The procedure to add a static FDB entry in sja1105 is concurrent with
dynamic learning performed on all bridge ports and the CPU port.
The switch looks up the FDB from left to right, and also learns
dynamically from left to right, so it is possible that between the
moment when we pick up a free slot to install an FDB entry, another slot
to the left of that one becomes free due to an address ageing out, and
that other slot is then immediately used by the switch to learn
dynamically the same address as we're trying to add statically.
The result is that we succeeded to add our static FDB entry, but it is
being shadowed by a dynamic FDB entry to its left, and the switch will
behave as if our static FDB entry did not exist.
We cannot really prevent this from happening unless we make the entire
process to add a static FDB entry a huge critical section where address
learning is temporarily disabled on _all_ ports, and then re-enabled
according to the configuration done by sja1105_port_set_learning.
However, that is kind of disruptive for the operation of the network.
What we can do alternatively is to simply read back the FDB for dynamic
entries located before our newly added static one, and delete them.
This will guarantee that our static FDB entry is now operational. It
will still not guarantee that there aren't dynamic FDB entries to the
_right_ of that static FDB entry, but at least those entries will age
out by themselves since they aren't hit, and won't bother anyone.
Fixes: 291d1e72b7 ("net: dsa: sja1105: Add support for FDB and MDB management")
Fixes: 1da7382134 ("net: dsa: sja1105: Add FDB operations for P/Q/R/S series")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e11e865bf8 ]
The SJA1105 switch family leaves it up to software to decide where
within the FDB to install a static entry, and to concatenate destination
ports for already existing entries (the FDB is also used for multicast
entries), it is not as simple as just saying "please add this entry".
This means we first need to search for an existing FDB entry before
adding a new one. The driver currently manages to fool itself into
thinking that if an FDB entry already exists, there is nothing to be
done. But that FDB entry might be dynamically learned, case in which it
should be replaced with a static entry, but instead it is left alone.
This patch checks the LOCKEDS ("locked/static") bit from found FDB
entries, and lets the code "goto skip_finding_an_index;" if the FDB
entry was not static. So we also need to move the place where we set
LOCKEDS = true, to cover the new case where a dynamic FDB entry existed
but was dynamic.
Fixes: 291d1e72b7 ("net: dsa: sja1105: Add support for FDB and MDB management")
Fixes: 1da7382134 ("net: dsa: sja1105: Add FDB operations for P/Q/R/S series")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d51c5907e9 ]
GSO expects inner transport header offset to be valid when
skb->encapsulation flag is set. GSO uses this value to calculate the length
of an individual segment of a GSO packet in skb_gso_transport_seglen().
However, tcp/udp gro_complete callbacks don't update the
skb->inner_transport_header when processing an encapsulated TCP/UDP
segment. As a result a GRO skb has ->inner_transport_header set to a value
carried over from earlier skb processing.
This can have mild to tragic consequences. From miscalculating the GSO
segment length to triggering a page fault [1], when trying to read TCP/UDP
header at an address past the skb->data page.
The latter scenario leads to an oops report like so:
BUG: unable to handle page fault for address: ffff9fa7ec00d008
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 123f201067 P4D 123f201067 PUD 123f209067 PMD 0
Oops: 0000 [#1] SMP NOPTI
CPU: 44 PID: 0 Comm: swapper/44 Not tainted 5.4.53-cloudflare-2020.7.21 #1
Hardware name: HYVE EDGE-METAL-GEN10/HS-1811DLite1, BIOS V2.15 02/21/2020
RIP: 0010:skb_gso_transport_seglen+0x44/0xa0
Code: c0 41 83 e0 11 f6 87 81 00 00 00 20 74 30 0f b7 87 aa 00 00 00 0f [...]
RSP: 0018:ffffad8640bacbb8 EFLAGS: 00010202
RAX: 000000000000feda RBX: ffff9fcc8d31bc00 RCX: ffff9fa7ec00cffc
RDX: ffff9fa7ebffdec0 RSI: 000000000000feda RDI: 0000000000000122
RBP: 00000000000005c4 R08: 0000000000000001 R09: 0000000000000000
R10: ffff9fe588ae3800 R11: ffff9fe011fc92f0 R12: ffff9fcc8d31bc00
R13: ffff9fe0119d4300 R14: 00000000000005c4 R15: ffff9fba57d70900
FS: 0000000000000000(0000) GS:ffff9fe68df00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffff9fa7ec00d008 CR3: 0000003e99b1c000 CR4: 0000000000340ee0
Call Trace:
<IRQ>
skb_gso_validate_network_len+0x11/0x70
__ip_finish_output+0x109/0x1c0
ip_sublist_rcv_finish+0x57/0x70
ip_sublist_rcv+0x2aa/0x2d0
? ip_rcv_finish_core.constprop.0+0x390/0x390
ip_list_rcv+0x12b/0x14f
__netif_receive_skb_list_core+0x2a9/0x2d0
netif_receive_skb_list_internal+0x1b5/0x2e0
napi_complete_done+0x93/0x140
veth_poll+0xc0/0x19f [veth]
? mlx5e_napi_poll+0x221/0x610 [mlx5_core]
net_rx_action+0x1f8/0x790
__do_softirq+0xe1/0x2bf
irq_exit+0x8e/0xc0
do_IRQ+0x58/0xe0
common_interrupt+0xf/0xf
</IRQ>
The bug can be observed in a simple setup where we send IP/GRE/IP/TCP
packets into a netns over a veth pair. Inside the netns, packets are
forwarded to dummy device:
trafgen -> [veth A]--[veth B] -forward-> [dummy]
For veth B to GRO aggregate packets on receive, it needs to have an XDP
program attached (for example, a trivial XDP_PASS). Additionally, for UDP,
we need to enable GSO_UDP_L4 feature on the device:
ip netns exec A ethtool -K AB rx-udp-gro-forwarding on
The last component is an artificial delay to increase the chances of GRO
batching happening:
ip netns exec A tc qdisc add dev AB root \
netem delay 200us slot 5ms 10ms packets 2 bytes 64k
With such a setup in place, the bug can be observed by tracing the skb
outer and inner offsets when GSO skb is transmitted from the dummy device:
tcp:
FUNC DEV SKB_LEN NH TH ENC INH ITH GSO_SIZE GSO_TYPE
ip_finish_output dumB 2830 270 290 1 294 254 1383 (tcpv4,gre,)
^^^
udp:
FUNC DEV SKB_LEN NH TH ENC INH ITH GSO_SIZE GSO_TYPE
ip_finish_output dumB 2818 270 290 1 294 254 1383 (gre,udp_l4,)
^^^
Fix it by updating the inner transport header offset in tcp/udp
gro_complete callbacks, similar to how {inet,ipv6}_gro_complete callbacks
update the inner network header offset, when skb->encapsulation flag is
set.
[1] https://lore.kernel.org/netdev/CAKxSbF01cLpZem2GFaUaifh0S-5WYViZemTicAg7FCHOnh6kug@mail.gmail.com/
Fixes: bf296b125b ("tcp: Add GRO support")
Fixes: f993bc25e5 ("net: core: handle encapsulation offloads when computing segment lengths")
Fixes: e20cf8d3f1 ("udp: implement GRO for plain UDP sockets.")
Reported-by: Alex Forster <aforster@cloudflare.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7199ddede9 ]
Commit dea7a9fbb0 ("dmaengine: imx-dma: remove dma_slave_config
direction usage") changes the method from a "configuration when called"
to an "configuration when used". Due to this, only the cyclic DMA type
gets configured correctly, while the generic DMA type is left
non-configured.
Without this additional call, the struct imxdma_channel::word_size member
is stuck at DMA_SLAVE_BUSWIDTH_UNDEFINED and imxdma_prep_slave_sg() always
returns NULL.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Fixes: dea7a9fbb0 ("dmaengine: imx-dma: remove dma_slave_config direction usage")
Link: https://lore.kernel.org/r/20210729071821.9857-1-jbe@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15f68f027e ]
While 7e5f3155dc ("ARM: dts: stm32: Fix LED5 on STM32MP1 DHCOM PDK2")
fixed the LED0 assignment on the PDK2 board, the same commit did not
update the touchscreen IRQ line assignment, which is the same GPIO line,
shared between the LED0 output and touchscreen IRQ input. To make this
more convoluted, the same EXTI input (not the same GPIO line) is shared
between Button B which is Active-Low IRQ, and touchscreen IRQ which is
Edge-Falling IRQ, which cannot be used at the same time. In case the LCD
board with touchscreen is in use, which is the case here, LED0 must be
disabled, Button B must be polled, so the touchscreen interrupt works as
it should.
Update the touchscreen IRQ line assignment, disable LED0 and use polled
GPIO button driver for Button B, since the DT here describes baseboard
with LCD board.
Fixes: 7e5f3155dc ("ARM: dts: stm32: Fix LED5 on STM32MP1 DHCOM PDK2")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36862c1ebc ]
The LAN8710 Energy Detect Power Down (EDPD) functionality might cause
unreliable cable detection. There are multiple accounts of this in the
SMSC PHY driver patches which attempted to make EDPD reliable, however
it seems there is always some sort of corner case left. Unfortunatelly,
there is no errata documented which would confirm this to be a silicon
bug on the LAN87xx series of PHYs (LAN8700, LAN8710, LAN8720 at least).
Disable EDPD on the DHCOM SoM, just like multiple other boards already
do as well, to make the cable detection reliable.
Fixes: 34e0c7847d ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c592b46907 ]
If a vb2_queue sets q->min_buffers_needed then when the number of
queued buffers reaches q->min_buffers_needed, vb2_core_qbuf() will call
the start_streaming() callback. If start_streaming() returns an error,
then that error was just returned by vb2_core_qbuf(), but the buffer
was still queued. However, userspace expects that if VIDIOC_QBUF fails,
the buffer is returned dequeued.
So if start_streaming() fails, then remove the buffer from the queue,
thus avoiding this unwanted side-effect.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Fixes: b3379c6201 ("[media] vb2: only call start_streaming if sufficient buffers are queued")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c04243a56 ]
Media event code 3 is defined in the MMC-6 spec as follows:
"MediaRemoval: The media has been removed from the specified slot, and
the Drive is unable to access the media without user intervention. This
applies to media changers only."
This indicated that treating the condition as an EJECT_REQUEST was
appropriate. However, doing so had the unfortunate side-effect of causing
the drive tray to be physically ejected on resume. Instead treat the event
as a MEDIA_CHANGE request.
Fixes: 7dd753ca59 ("scsi: sr: Return appropriate error code when disk is ejected")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=213759
Link: https://lore.kernel.org/r/20210726114913.6760-1-limanyi@uniontech.com
Signed-off-by: Li Manyi <limanyi@uniontech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 53ca18acbe ]
The spi_imx->spi_bus_clk may be uninitialized and thus also zero in
mx51_ecspi_prepare_message(), which would lead to division by zero
in kernel. Since bitbang .setup_transfer callback which initializes
the spi_imx->spi_bus_clk is called after bitbang prepare_message
callback, iterate over all the transfers in spi_message, find the
one with lowest bus frequency, and use that bus frequency for the
delay calculation.
Note that it is not possible to move this CONFIGREG delay back into
the .setup_transfer callback, because that is invoked too late, after
the GPIO chipselects were already configured.
Fixes: 135cbd378e ("spi: imx: mx51-ecspi: Reinstate low-speed CONFIGREG delay")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210726100102.5188-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 135cbd378e ]
Since 00b80ac935 ("spi: imx: mx51-ecspi: Move some initialisation to
prepare_message hook."), the MX51_ECSPI_CONFIG write no longer happens
in prepare_transfer hook, but rather in prepare_message hook, however
the MX51_ECSPI_CONFIG delay is still left in prepare_transfer hook and
thus has no effect. This leads to low bus frequency operation problems
described in 6fd8b8503a ("spi: spi-imx: Fix out-of-order CS/SCLK
operation at low speeds") again.
Move the MX51_ECSPI_CONFIG write delay into the prepare_message hook
as well, thus reinstating the low bus frequency fix.
Fixes: 00b80ac935 ("spi: imx: mx51-ecspi: Move some initialisation to prepare_message hook.")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210703022300.296114-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d54db74ad6 ]
pm_runtime_get_sync will increment pm usage counter
even it failed. Forgetting to putting operation will
result in reference leak here. We fix it by replacing
it with pm_runtime_resume_and_get to keep usage counter
balanced.
Fixes: 48bc73ba14 ("dmaengine: stm32-dma: Add PM Runtime support")
Fixes: 05f8740a0e ("dmaengine: stm32-dma: add suspend/resume power management support")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20210607064640.121394-2-zhangqilong3@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c68ef4ad18 ]
This device tree include file describes a fixed-regulator
connecting smps7_reg output (1.8V) to some 1.8V rail and
consumers (vdds_1v8_main).
This regulator does not physically exist.
I assume it was introduced as a wrapper around smps7_reg
to provide a speaking signal name "vdds_1v8_main" as label.
This fixed-regulator without real function was not an issue
in driver code until
Commit 98e48cd928 ("regulator: core: resolve supply for boot-on/always-on regulators")
introduced a new check for regulator initialization which
makes Palmas regulator registration fail:
[ 5.407712] ldo1: supplied by vsys_cobra
[ 5.412748] ldo2: supplied by vsys_cobra
[ 5.417603] palmas-pmic 48070000.i2c:palmas@48:palmas_pmic: failed to register 48070000.i2c:palmas@48:palmas_pmic regulator
The reason is that the supply-chain of regulators is too
long and goes from ldo3 through the virtual vdds_1v8_main
regulator and then back to smps7. This adds a cross-dependency
of probing Palmas regulators and the fixed-regulator which
leads to probe deferral by the new check and is no longer
resolved.
Since we do not control what device tree files including this
one reference (either &vdds_1v8_main or &smps7_reg or both)
we keep both labels for smps7 for compatibility.
Fixes: 98e48cd928 ("regulator: core: resolve supply for boot-on/always-on regulators")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24b5b1978c ]
Enabling the framebuffer leads to a system hang. Running, as a debug
hack, the store_pan() function in drivers/video/fbdev/core/fbsysfs.c
without taking the console_lock, allows to see the crash backtrace on
the serial line.
~ # echo 0 0 > /sys/class/graphics/fb0/pan
[ 9.719414] Unhandled exception: IPSR = 00000005 LR = fffffff1
[ 9.726937] CPU: 0 PID: 49 Comm: sh Not tainted 5.13.0-rc5 #9
[ 9.733008] Hardware name: STM32 (Device Tree Support)
[ 9.738296] PC is at clk_gate_is_enabled+0x0/0x28
[ 9.743426] LR is at stm32f4_pll_div_set_rate+0xf/0x38
[ 9.748857] pc : [<0011e4be>] lr : [<0011f9e3>] psr: 0100000b
[ 9.755373] sp : 00bc7be0 ip : 00000000 fp : 001f3ac4
[ 9.760812] r10: 002610d0 r9 : 01efe920 r8 : 00540560
[ 9.766269] r7 : 02e7ddb0 r6 : 0173eed8 r5 : 00000000 r4 : 004027c0
[ 9.773081] r3 : 0011e4bf r2 : 02e7ddb0 r1 : 0173eed8 r0 : 1d3267b8
[ 9.779911] xPSR: 0100000b
[ 9.782719] CPU: 0 PID: 49 Comm: sh Not tainted 5.13.0-rc5 #9
[ 9.788791] Hardware name: STM32 (Device Tree Support)
[ 9.794120] [<0000afa1>] (unwind_backtrace) from [<0000a33f>] (show_stack+0xb/0xc)
[ 9.802421] [<0000a33f>] (show_stack) from [<0000a8df>] (__invalid_entry+0x4b/0x4c)
The `pll_num' field in the post_div_data configuration contained a wrong
value which also referenced an uninitialized hardware clock when
clk_register_pll_div() was called.
Fixes: 517633ef63 ("clk: stm32f4: Add post divisor for I2S & SAI PLLs")
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Link: https://lore.kernel.org/r/20210725160725.10788-1-dariobin@libero.it
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4511781f95 ]
The following scenario describes an echo test for
Samsung USBC Headset (AKG) with VID/PID (0x04e8/0xa051).
We first start a capture stream(USB IN transfer) in 96Khz/24bit/1ch mode.
In clock find source function, we get value 0x2 for clock selector
and 0x1 for clock source.
Kernel-4.14 behavior
Since clock source is valid so clock selector was not set again.
We pass through this function and start a playback stream(USB OUT transfer)
in 48Khz/32bit/2ch mode. This time we get value 0x1 for clock selector
and 0x1 for clock source. Finally clock id with this setting is 0x9.
Kernel-5.10 behavior
Clock selector was always set one more time even it is valid.
When we start a playback stream, we will get 0x2 for clock selector
and 0x1 for clock source. In this case clock id becomes 0xA.
This is an incorrect clock source setting and results in severe noises.
We see wrong data rate in USB IN transfer.
(From 288 bytes/ms becomes 144 bytes/ms) It should keep in 288 bytes/ms.
This earphone works fine on older kernel version load because
this is a newly-added behavior.
Fixes: d2e8f64125 ("ALSA: usb-audio: Explicitly set up the clock selector")
Signed-off-by: chihhao.chen <chihhao.chen@mediatek.com>
Link: https://lore.kernel.org/r/1627100621-19225-1-git-send-email-chihhao.chen@mediatek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee7ab3f263 ]
Some SFP modules are not detected when i2c-fast-mode is enabled even when
clock-frequency is already set to 100000. The I2C bus violates the timing
specifications when run in fast mode. So disable fast mode on Turris Mox.
Same change was already applied for uDPU (also Armada 3720 board with SFP)
in commit fe3ec631a7 ("arm64: dts: uDPU: remove i2c-fast-mode").
Fixes: 7109d817db ("arm64: dts: marvell: add DTS for Turris Mox")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 923f989291 ]
Since drivers/mmc/host/sdhci-xenon.c declares the PROBE_PREFER_ASYNCHRONOUS
probe type, it is not guaranteed whether /dev/mmcblk0 will belong to
sdhci0 or sdhci1. In turn, this will break booting by:
root=/dev/mmcblk0p1
Fix the issue by adding aliases so that the old MMC controller indices
are preserved.
Fixes: 7320915c88 ("mmc: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in v4.14")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d9e30a520 ]
The pinctrl_power_button/pinctrl_power_out each define single GPIO
pinmux, except it is exactly the other one than the matching gpio-keys
and gpio-poweroff DT nodes use for that functionality. Swap the two
GPIOs to correct this error.
Fixes: 50d29fdb76 ("ARM: dts: imx53: Add power GPIOs on M53Menlo")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20fb73911f ]
The function imx_mmdc_perf_init recently had a 3rd argument added to
it but the equivalent macro was not updated and is still the older
2 argument version. Fix this by adding in the missing 3rd argumement
mmdc_ipg_clk.
Fixes: f07ec85365 ("ARM: imx: add missing clk_disable_unprepare()")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 29f6a20c21 ]
The PHY configuration for the variant 2 is still missing the flag for
in-band signalling between PHY and MAC. Both sides - MAC and PHY - have
to match the setting. For now, Linux only supports setting the MAC side
and thus it has to match the setting the bootloader is configuring.
Enable in-band signalling to make ethernet work.
Fixes: ab43f03074 ("arm64: dts: ls1028a: sl28: add support for variant 2")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd8e83884f ]
The AR803x PHY used on this modules seems to require the reset line to
be asserted for around 10ms in order to avoid rare cases where the PHY
gets stuck in an incoherent state that prevents it to function
correctly.
The previous value of 2ms was found to be problematic on some setups,
causing intermittent issues where the PHY would be unresponsive
every once in a while on some sytems, with a low occurrence (it typically
took around 30 consecutive reboots to encounter the issue).
Bumping the delay to the 10ms makes the issue dissapear, with more than
2500 consecutive reboots performed without the issue showing-up.
Fixes: 208d7baf80 ("ARM: imx: initial SolidRun HummingBoard support")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Hervé Codina <herve.codina@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f07ec85365 ]
clock source is prepared and enabled by clk_prepare_enable()
in probe function, but no disable or unprepare in remove and
error path.
Fixes: 9454a0caff ("ARM: imx: add mmdc ipg clock operation for mmdc")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9613aa07f ]
Commit e76bdfd740 ("ARM: imx: Added perf functionality to mmdc driver")
introduced imx_mmdc_remove(), the mmdc_base need be unmapped in it if
config PERF_EVENTS is enabled.
If imx_mmdc_perf_init() fails, the mmdc_base also need be unmapped.
Fixes: e76bdfd740 ("ARM: imx: Added perf functionality to mmdc driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e71b85473 ]
U-Boot attempts to fix up the "clock-frequency" property of the "/sysclk" node:
https://elixir.bootlin.com/u-boot/v2021.04/source/arch/arm/cpu/armv8/fsl-layerscape/fdt.c#L512
but fails to do so:
## Booting kernel from Legacy Image at a1000000 ...
Image Name:
Created: 2021-06-08 10:31:38 UTC
Image Type: AArch64 Linux Kernel Image (gzip compressed)
Data Size: 15431370 Bytes = 14.7 MiB
Load Address: 80080000
Entry Point: 80080000
Verifying Checksum ... OK
## Flattened Device Tree blob at a0000000
Booting using the fdt blob at 0xa0000000
Uncompressing Kernel Image
Loading Device Tree to 00000000fbb19000, end 00000000fbb22717 ... OK
Unable to update property /sysclk:clock-frequency, err=FDT_ERR_NOTFOUND
Starting kernel ...
All Layerscape SoCs except LS1028A use "sysclk" as the node name, and
not "clock-sysclk". So change the node name of LS1028A accordingly.
Fixes: 8897f3255c ("arm64: dts: Add support for NXP LS1028A SoC")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c1a80e80c ]
Syzbot reported memory leak in xfrm_user_rcv_msg(). The
problem was is non-freed skb's frag_list.
In skb_release_all() skb_release_data() will be called only
in case of skb->head != NULL, but netlink_skb_destructor()
sets head to NULL. So, allocated frag_list skb should be
freed manualy, since consume_skb() won't take care of it
Fixes: 5106f4a8ac ("xfrm/compat: Add 32=>64-bit messages translator")
Reported-and-tested-by: syzbot+fb347cf82c73a90efcca@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ff340e24c ]
Jarkko Nikula <jarkko.nikula@bitmer.com> reported that Beagleboard
revision c2 stopped booting. Jarkko bisected the issue down to
commit 6cfcd5563b ("clocksource/drivers/timer-ti-dm: Fix suspend
and resume for am3 and am4").
Let's fix the issue by tagging system timers as reserved rather than
ignoring them. And let's not probe any interconnect target module child
devices for reserved modules.
This allows PM runtime to keep track of clocks and clockdomains for
the interconnect target module, and prevent the system timer from idling
as we already have SYSC_QUIRK_NO_IDLE and SYSC_QUIRK_NO_IDLE_ON_INIT
flags set for system timers.
Fixes: 6cfcd5563b ("clocksource/drivers/timer-ti-dm: Fix suspend and resume for am3 and am4")
Reported-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 97367c9722 upstream.
It turned out that the current implementation of the port subscription
is racy. The subscription contains two linked lists, and we have to
add to or delete from both lists. Since both connection and
disconnection procedures perform the same order for those two lists
(i.e. src list, then dest list), when a deletion happens during a
connection procedure, the src list may be deleted before the dest list
addition completes, and this may lead to a use-after-free or an Oops,
even though the access to both lists are protected via mutex.
The simple workaround for this race is to change the access order for
the disconnection, namely, dest list, then src list. This assures
that the connection has been established when disconnecting, and also
the concurrent deletion can be avoided.
Reported-and-tested-by: folkert <folkert@vanheusden.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210801182754.GP890690@belle.intranet.vanheusden.com
Link: https://lore.kernel.org/r/20210803114312.2536-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6511a8b5b7 upstream.
Revert commit c27bac0314 ("ACPICA: Fix memory leak caused by _CID
repair function") which is reported to cause a boot issue on Acer
Swift 3 (SF314-51).
Reported-by: Adrien Precigout <dev@asdrip.fr>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d5c3954b3 upstream.
Commit 3a70dd2d05 ("spi: mediatek: fix fifo rx mode") claims that
fifo RX mode was never handled, and adds the presumably missing code
to the FIFO transfer function. However, the claim that receive data
was not handled is incorrect. It was handled as part of interrupt
handling after the transfer was complete. The code added with the above
mentioned commit reads data from the receive FIFO before the transfer
is started, which is wrong. This results in an actual transfer error
on a Hayato Chromebook.
Remove the code trying to handle receive data before the transfer is
started to fix the problem.
Fixes: 3a70dd2d05 ("spi: mediatek: fix fifo rx mode")
Cc: Peter Hess <peter.hess@ph-home.de>
Cc: Frank Wunderlich <frank-w@public-files.de>
Cc: Tzung-Bi Shih <tzungbi@google.com>
Cc: Hsin-Yi Wang <hsinyi@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Hsin-Yi Wang <hsinyi@google.com>
Tested-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20210802030023.1748777-1-linux@roeck-us.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 973377ffe8 upstream
In almost all cases from test_verifier that have been changed in here, we've
had an unreachable path with a load from a register which has an invalid
address on purpose. This was basically to make sure that we never walk this
path and to have the verifier complain if it would otherwise. Change it to
match on the right error for unprivileged given we now test these paths
under speculative execution.
There's one case where we match on exact # of insns_processed. Due to the
extra path, this will of course mismatch on unprivileged. Thus, restrict the
test->insn_processed check to privileged-only.
In one other case, we result in a 'pointer comparison prohibited' error. This
is similarly due to verifying an 'invalid' branch where we end up with a value
pointer on one side of the comparison.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d7a5091351 upstream
Update various selftest error messages:
* The 'Rx tried to sub from different maps, paths, or prohibited types'
is reworked into more specific/differentiated error messages for better
guidance.
* The change into 'value -4294967168 makes map_value pointer be out of
bounds' is due to moving the mixed bounds check into the speculation
handling and thus occuring slightly later than above mentioned sanity
check.
* The change into 'math between map_value pointer and register with
unbounded min value' is similarly due to register sanity check coming
before the mixed bounds check.
* The case of 'map access: known scalar += value_ptr from different maps'
now loads fine given masks are the same from the different paths (despite
max map value size being different).
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1bad6fd52b upstream
Given we don't need to simulate the speculative domain for registers with
immediates anymore since the verifier uses direct imm-based rewrites instead
of having to mask, we can also lift a few cases that were previously rejected.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d7940911fc ]
[Why]
Vertical and horizontal borders in timings are treated as increasing the
active area - vblank and hblank actually shrink.
Our input into DML does not include these borders so it incorrectly
assumes it has more time than available for vstartup and tmdl
calculations for some modes with borders.
An example of such a timing would be 640x480@72Hz:
h_total: 832
h_border_left: 8
h_addressable: 640
h_border_right: 8
h_front_porch: 16
h_sync_width: 40
v_total: 520
v_border_top: 8
v_addressable: 480
v_border_bottom: 8
v_front_porch: 1
v_sync_width: 3
pix_clk_100hz: 315000
[How]
Include borders as part of destination vactive/hactive.
This change DCN20+ so it has wide impact, but the destination vactive
and hactive are only really used for vstartup calculation anyway.
Most modes do not have vertical or horizontal borders.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 234211b8dd ]
The metadata address is set after the trace event, so the trace is not
capturing anything useful. Rather than logging the memory address, it's
useful to know if the command carries a metadata payload, so change the
trace event to log that true/false state instead.
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47e1e233e9 ]
One of the SUSE QA tests triggered:
localhost kernel: efi: Failed to lookup EFI memory descriptor for 0x000000003dcf8000
which comes from x86's version of efi_arch_mem_reserve() trying to
reserve a memory region. Usually, that function expects
EFI_BOOT_SERVICES_DATA memory descriptors but the above case is for the
MOKvar table which is allocated in the EFI shim as runtime services.
That lead to a fix changing the allocation of that table to boot services.
However, that fix broke booting SEV guests with that shim leading to
this kernel fix
8d651ee9c7 ("x86/ioremap: Map EFI-reserved memory as encrypted for SEV")
which extended the ioremap hint to map reserved EFI boot services as
decrypted too.
However, all that wasn't needed, IMO, because that error message in
efi_arch_mem_reserve() was innocuous in this case - if the MOKvar table
is not in boot services, then it doesn't need to be reserved in the
first place because it is, well, in runtime services which *should* be
reserved anyway.
So do that reservation for the MOKvar table only if it is allocated
in boot services data. I couldn't find any requirement about where
that table should be allocated in, unlike the ESRT which allocation is
mandated to be done in boot services data by the UEFI spec.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a17ad09617 ]
In some cases skb head could be locked and entire header
data is pulled from skb. When skb_zerocopy() called in such cases,
following BUG is triggered. This patch fixes it by copying entire
skb in such cases.
This could be optimized incase this is performance bottleneck.
---8<---
kernel BUG at net/core/skbuff.c:2961!
invalid opcode: 0000 [#1] SMP PTI
CPU: 2 PID: 0 Comm: swapper/2 Tainted: G OE 5.4.0-77-generic #86-Ubuntu
Hardware name: OpenStack Foundation OpenStack Nova, BIOS 1.13.0-1ubuntu1.1 04/01/2014
RIP: 0010:skb_zerocopy+0x37a/0x3a0
RSP: 0018:ffffbcc70013ca38 EFLAGS: 00010246
Call Trace:
<IRQ>
queue_userspace_packet+0x2af/0x5e0 [openvswitch]
ovs_dp_upcall+0x3d/0x60 [openvswitch]
ovs_dp_process_packet+0x125/0x150 [openvswitch]
ovs_vport_receive+0x77/0xd0 [openvswitch]
netdev_port_receive+0x87/0x130 [openvswitch]
netdev_frame_hook+0x4b/0x60 [openvswitch]
__netif_receive_skb_core+0x2b4/0xc90
__netif_receive_skb_one_core+0x3f/0xa0
__netif_receive_skb+0x18/0x60
process_backlog+0xa9/0x160
net_rx_action+0x142/0x390
__do_softirq+0xe1/0x2d6
irq_exit+0xae/0xb0
do_IRQ+0x5a/0xf0
common_interrupt+0xf/0xf
Code that triggered BUG:
int
skb_zerocopy(struct sk_buff *to, struct sk_buff *from, int len, int hlen)
{
int i, j = 0;
int plen = 0; /* length of skb->head fragment */
int ret;
struct page *page;
unsigned int offset;
BUG_ON(!from->head_frag && !hlen);
Signed-off-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6206b7981a ]
Liajian reported a bug_on hit on a ThunderX2 arm64 server with FastLinQ
QL41000 ethernet controller:
BUG: scheduling while atomic: kworker/0:4/531/0x00000200
[qed_probe:488()]hw prepare failed
kernel BUG at mm/vmalloc.c:2355!
Internal error: Oops - BUG: 0 [#1] SMP
CPU: 0 PID: 531 Comm: kworker/0:4 Tainted: G W 5.4.0-77-generic #86-Ubuntu
pstate: 00400009 (nzcv daif +PAN -UAO)
Call trace:
vunmap+0x4c/0x50
iounmap+0x48/0x58
qed_free_pci+0x60/0x80 [qed]
qed_probe+0x35c/0x688 [qed]
__qede_probe+0x88/0x5c8 [qede]
qede_probe+0x60/0xe0 [qede]
local_pci_probe+0x48/0xa0
work_for_cpu_fn+0x24/0x38
process_one_work+0x1d0/0x468
worker_thread+0x238/0x4e0
kthread+0xf0/0x118
ret_from_fork+0x10/0x18
In this case, qed_hw_prepare() returns error due to hw/fw error, but in
theory work queue should be in process context instead of interrupt.
The root cause might be the unpaired spin_{un}lock_bh() in
_qed_mcp_cmd_and_union(), which causes botton half is disabled incorrectly.
Reported-by: Lijian Zhang <Lijian.Zhang@arm.com>
Signed-off-by: Jia He <justin.he@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6549c46af8 ]
For linear regulators, the n_voltages should be (max - min) / step + 1.
Buck voltage from 1v to 3V, per step 100mV, and vout mask is 0x1f.
If value is from 20 to 31, the voltage will all be fixed to 3V.
And LDO also, just vout range is different from 1.2v to 3v, step is the
same. If value is from 18 to 31, the voltage will also be fixed to 3v.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/20210627080418.1718127-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ecc64fab7d ]
When checking if we need to log the new name of a renamed inode, we are
checking if the inode and its parent inode have been logged before, and if
not we don't log the new name. The check however is buggy, as it directly
compares the logged_trans field of the inodes versus the ID of the current
transaction. The problem is that logged_trans is a transient field, only
stored in memory and never persisted in the inode item, so if an inode
was logged before, evicted and reloaded, its logged_trans field is set to
a value of 0, meaning the check will return false and the new name of the
renamed inode is not logged. If the old parent directory was previously
fsynced and we deleted the logged directory entries corresponding to the
old name, we end up with a log that when replayed will delete the renamed
inode.
The following example triggers the problem:
$ mkfs.btrfs -f /dev/sdc
$ mount /dev/sdc /mnt
$ mkdir /mnt/A
$ mkdir /mnt/B
$ echo -n "hello world" > /mnt/A/foo
$ sync
# Add some new file to A and fsync directory A.
$ touch /mnt/A/bar
$ xfs_io -c "fsync" /mnt/A
# Now trigger inode eviction. We are only interested in triggering
# eviction for the inode of directory A.
$ echo 2 > /proc/sys/vm/drop_caches
# Move foo from directory A to directory B.
# This deletes the directory entries for foo in A from the log, and
# does not add the new name for foo in directory B to the log, because
# logged_trans of A is 0, which is less than the current transaction ID.
$ mv /mnt/A/foo /mnt/B/foo
# Now make an fsync to anything except A, B or any file inside them,
# like for example create a file at the root directory and fsync this
# new file. This syncs the log that contains all the changes done by
# previous rename operation.
$ touch /mnt/baz
$ xfs_io -c "fsync" /mnt/baz
<power fail>
# Mount the filesystem and replay the log.
$ mount /dev/sdc /mnt
# Check the filesystem content.
$ ls -1R /mnt
/mnt/:
A
B
baz
/mnt/A:
bar
/mnt/B:
$
# File foo is gone, it's neither in A/ nor in B/.
Fix this by using the inode_logged() helper at btrfs_log_new_name(), which
safely checks if an inode was logged before in the current transaction.
A test case for fstests will follow soon.
CC: stable@vger.kernel.org # 4.14+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de53d892e5 ]
When we are doing a rename or a link operation for an inode that was logged
in the previous transaction and that transaction is still committing, we
have a time window where we incorrectly consider that the inode was logged
previously in the current transaction and therefore decide to log it to
update it in the log. The following steps give an example on how this
happens during a link operation:
1) Inode X is logged in transaction 1000, so its logged_trans field is set
to 1000;
2) Task A starts to commit transaction 1000;
3) The state of transaction 1000 is changed to TRANS_STATE_UNBLOCKED;
4) Task B starts a link operation for inode X, and as a consequence it
starts transaction 1001;
5) Task A is still committing transaction 1000, therefore the value stored
at fs_info->last_trans_committed is still 999;
6) Task B calls btrfs_log_new_name(), it reads a value of 999 from
fs_info->last_trans_committed and because the logged_trans field of
inode X has a value of 1000, the function does not return immediately,
instead it proceeds to logging the inode, which should not happen
because the inode was logged in the previous transaction (1000) and
not in the current one (1001).
This is not a functional problem, just wasted time and space logging an
inode that does not need to be logged, contributing to higher latency
for link and rename operations.
So fix this by comparing the inodes' logged_trans field with the
generation of the current transaction instead of comparing with the value
stored in fs_info->last_trans_committed.
This case is often hit when running dbench for a long enough duration, as
it does lots of rename operations.
This patch belongs to a patch set that is comprised of the following
patches:
btrfs: fix race causing unnecessary inode logging during link and rename
btrfs: fix race that results in logging old extents during a fast fsync
btrfs: fix race that causes unnecessary logging of ancestor inodes
btrfs: fix race that makes inode logging fallback to transaction commit
btrfs: fix race leading to unnecessary transaction commit when logging inode
btrfs: do not block inode logging for so long during transaction commit
Performance results are mentioned in the change log of the last patch.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3761baae90 upstream.
This reverts commit 9e31c1fe45. Ever
since that commit, we've been having issues where a hang in one client
can propagate to another. In particular, a hang in an app can propagate
to the X server which causes the whole desktop to lock up.
Error propagation along fences sound like a good idea, but as your bug
shows, surprising consequences, since propagating errors across security
boundaries is not a good thing.
What we do have is track the hangs on the ctx, and report information to
userspace using RESET_STATS. That's how arb_robustness works. Also, if my
understanding is still correct, the EIO from execbuf is when your context
is banned (because not recoverable or too many hangs). And in all these
cases it's up to userspace to figure out what is all impacted and should
be reported to the application, that's not on the kernel to guess and
automatically propagate.
What's more, we're also building more features on top of ctx error
reporting with RESET_STATS ioctl: Encrypted buffers use the same, and the
userspace fence wait also relies on that mechanism. So it is the path
going forward for reporting gpu hangs and resets to userspace.
So all together that's why I think we should just bury this idea again as
not quite the direction we want to go to, hence why I think the revert is
the right option here.
For backporters: Please note that you _must_ have a backport of
https://lore.kernel.org/dri-devel/20210602164149.391653-2-jason@jlekstrand.net/
for otherwise backporting just this patch opens up a security bug.
v2: Augment commit message. Also restore Jason's sob that I
accidentally lost.
v3: Add a note for backporters
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Reported-by: Marcin Slusarz <marcin.slusarz@intel.com>
Cc: <stable@vger.kernel.org> # v5.6+
Cc: Jason Ekstrand <jason.ekstrand@intel.com>
Cc: Marcin Slusarz <marcin.slusarz@intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/3080
Fixes: 9e31c1fe45 ("drm/i915: Propagate errors on awaiting already signaled fences")
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Jon Bloomfield <jon.bloomfield@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210714193419.1459723-3-jason@jlekstrand.net
(cherry picked from commit 93a2711cdd)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c9d9fdbc10 upstream.
This reverts 686c7c35ab ("drm/i915/gem: Asynchronous cmdparser"). The
justification for this commit in the git history was a vague comment
about getting it out from under the struct_mutex. While this may
improve perf for some workloads on Gen7 platforms where we rely on the
command parser for features such as indirect rendering, no numbers were
provided to prove such an improvement. It claims to closed two
gitlab/bugzilla issues but with no explanation whatsoever as to why or
what bug it's fixing.
Meanwhile, by moving command parsing off to an async callback, it leaves
us with a problem of what to do on error. When things were synchronous,
EXECBUFFER2 would fail with an error code if parsing failed. When
moving it to async, we needed another way to handle that error and the
solution employed was to set an error on the dma_fence and then trust
that said error gets propagated to the client eventually. Moving back
to synchronous will help us untangle the fence error propagation mess.
This also reverts most of 0edbb9ba1b ("drm/i915: Move cmd parser
pinning to execbuffer") which is a refactor of some of our allocation
paths for asynchronous parsing. Now that everything is synchronous, we
don't need it.
v2 (Daniel Vetter):
- Add stabel Cc and Fixes tag
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Cc: <stable@vger.kernel.org> # v5.6+
Fixes: 9e31c1fe45 ("drm/i915: Propagate errors on awaiting already signaled fences")
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Jon Bloomfield <jon.bloomfield@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210714193419.1459723-2-jason@jlekstrand.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0c71437dd5 upstream.
The j1939_session_deactivate() is decrementing the session ref-count and
potentially can free() the session. This would cause use-after-free
situation.
However, the code calling j1939_session_deactivate() does always hold
another reference to the session, so that it would not be free()ed in
this code path.
This patch adds a comment to make this clear and a WARN_ON, to ensure
that future changes will not violate this requirement. Further this
patch avoids dereferencing the session pointer as a precaution to avoid
use-after-free if the session is actually free()ed.
Fixes: 9d71dd0c70 ("can: add support of SAE J1939 protocol")
Link: https://lore.kernel.org/r/20210714111602.24021-1-o.rempel@pengutronix.de
Reported-by: Xiaochen Zou <xzou017@ucr.edu>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 333cf50746 upstream.
With commit c9f3401313 ("powerpc: Always enable queued spinlocks for
64s, disable for others") CONFIG_PPC_QUEUED_SPINLOCKS is always
enabled on ppc64le, external modules that use spinlock APIs are
failing.
ERROR: modpost: GPL-incompatible module XXX.ko uses GPL-only symbol 'shared_processor'
Before the above commit, modules were able to build without any
issues. Also this problem is not seen on other architectures. This
problem can be workaround if CONFIG_UNINLINE_SPIN_UNLOCK is enabled in
the config. However CONFIG_UNINLINE_SPIN_UNLOCK is not enabled by
default and only enabled in certain conditions like
CONFIG_DEBUG_SPINLOCKS is set in the kernel config.
#include <linux/module.h>
spinlock_t spLock;
static int __init spinlock_test_init(void)
{
spin_lock_init(&spLock);
spin_lock(&spLock);
spin_unlock(&spLock);
return 0;
}
static void __exit spinlock_test_exit(void)
{
printk("spinlock_test unloaded\n");
}
module_init(spinlock_test_init);
module_exit(spinlock_test_exit);
MODULE_DESCRIPTION ("spinlock_test");
MODULE_LICENSE ("non-GPL");
MODULE_AUTHOR ("Srikar Dronamraju");
Given that spin locks are one of the basic facilities for module code,
this effectively makes it impossible to build/load almost any non GPL
modules on ppc64le.
This was first reported at https://github.com/openzfs/zfs/issues/11172
Currently shared_processor is exported as GPL only symbol.
Fix this for parity with other architectures by exposing
shared_processor to non-GPL modules too.
Fixes: 14c73bd344 ("powerpc/vcpu: Assume dedicated processors as non-preempt")
Cc: stable@vger.kernel.org # v5.5+
Reported-by: marc.c.dionne@gmail.com
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210729060449.292780-1-srikar@linux.vnet.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f2a26a3cff upstream.
readpage was calculating the offset of the page incorrectly
for the case of large swapcaches.
loff_t offset = (loff_t)page->index << PAGE_SHIFT;
As pointed out by Matthew Wilcox, this needs to use
page_file_offset() to calculate the offset instead.
Pages coming from the swap cache have page->index set
to their index within the swapcache, not within the backing
file. For a sufficiently large swapcache, we could have
overlapping values of page->index within the same backing file.
Suggested by: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: <stable@vger.kernel.org> # v5.7+
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e042aa532c upstream.
In 7fedb63a83 ("bpf: Tighten speculative pointer arithmetic mask") we
narrowed the offset mask for unprivileged pointer arithmetic in order to
mitigate a corner case where in the speculative domain it is possible to
advance, for example, the map value pointer by up to value_size-1 out-of-
bounds in order to leak kernel memory via side-channel to user space.
The verifier's state pruning for scalars leaves one corner case open
where in the first verification path R_x holds an unknown scalar with an
aux->alu_limit of e.g. 7, and in a second verification path that same
register R_x, here denoted as R_x', holds an unknown scalar which has
tighter bounds and would thus satisfy range_within(R_x, R_x') as well as
tnum_in(R_x, R_x') for state pruning, yielding an aux->alu_limit of 3:
Given the second path fits the register constraints for pruning, the final
generated mask from aux->alu_limit will remain at 7. While technically
not wrong for the non-speculative domain, it would however be possible
to craft similar cases where the mask would be too wide as in 7fedb63a83.
One way to fix it is to detect the presence of unknown scalar map pointer
arithmetic and force a deeper search on unknown scalars to ensure that
we do not run into a masking mismatch.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 59089a189e upstream.
Follow-up to fe9a5ca7e3 ("bpf: Do not mark insn as seen under speculative
path verification"). The sanitize_insn_aux_data() helper does not serve a
particular purpose in today's code. The original intention for the helper
was that if function-by-function verification fails, a given program would
be cleared from temporary insn_aux_data[], and then its verification would
be re-attempted in the context of the main program a second time.
However, a failure in do_check_subprogs() will skip do_check_main() and
propagate the error to the user instead, thus such situation can never occur.
Given its interaction is not compatible to the Spectre v1 mitigation (due to
comparing aux->seen with env->pass_cnt), just remove sanitize_insn_aux_data()
to avoid future bugs in this area.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2039f26f3a ]
Spectre v4 gadgets make use of memory disambiguation, which is a set of
techniques that execute memory access instructions, that is, loads and
stores, out of program order; Intel's optimization manual, section 2.4.4.5:
A load instruction micro-op may depend on a preceding store. Many
microarchitectures block loads until all preceding store addresses are
known. The memory disambiguator predicts which loads will not depend on
any previous stores. When the disambiguator predicts that a load does
not have such a dependency, the load takes its data from the L1 data
cache. Eventually, the prediction is verified. If an actual conflict is
detected, the load and all succeeding instructions are re-executed.
af86ca4e30 ("bpf: Prevent memory disambiguation attack") tried to mitigate
this attack by sanitizing the memory locations through preemptive "fast"
(low latency) stores of zero prior to the actual "slow" (high latency) store
of a pointer value such that upon dependency misprediction the CPU then
speculatively executes the load of the pointer value and retrieves the zero
value instead of the attacker controlled scalar value previously stored at
that location, meaning, subsequent access in the speculative domain is then
redirected to the "zero page".
The sanitized preemptive store of zero prior to the actual "slow" store is
done through a simple ST instruction based on r10 (frame pointer) with
relative offset to the stack location that the verifier has been tracking
on the original used register for STX, which does not have to be r10. Thus,
there are no memory dependencies for this store, since it's only using r10
and immediate constant of zero; hence af86ca4e30 /assumed/ a low latency
operation.
However, a recent attack demonstrated that this mitigation is not sufficient
since the preemptive store of zero could also be turned into a "slow" store
and is thus bypassed as well:
[...]
// r2 = oob address (e.g. scalar)
// r7 = pointer to map value
31: (7b) *(u64 *)(r10 -16) = r2
// r9 will remain "fast" register, r10 will become "slow" register below
32: (bf) r9 = r10
// JIT maps BPF reg to x86 reg:
// r9 -> r15 (callee saved)
// r10 -> rbp
// train store forward prediction to break dependency link between both r9
// and r10 by evicting them from the predictor's LRU table.
33: (61) r0 = *(u32 *)(r7 +24576)
34: (63) *(u32 *)(r7 +29696) = r0
35: (61) r0 = *(u32 *)(r7 +24580)
36: (63) *(u32 *)(r7 +29700) = r0
37: (61) r0 = *(u32 *)(r7 +24584)
38: (63) *(u32 *)(r7 +29704) = r0
39: (61) r0 = *(u32 *)(r7 +24588)
40: (63) *(u32 *)(r7 +29708) = r0
[...]
543: (61) r0 = *(u32 *)(r7 +25596)
544: (63) *(u32 *)(r7 +30716) = r0
// prepare call to bpf_ringbuf_output() helper. the latter will cause rbp
// to spill to stack memory while r13/r14/r15 (all callee saved regs) remain
// in hardware registers. rbp becomes slow due to push/pop latency. below is
// disasm of bpf_ringbuf_output() helper for better visual context:
//
// ffffffff8117ee20: 41 54 push r12
// ffffffff8117ee22: 55 push rbp
// ffffffff8117ee23: 53 push rbx
// ffffffff8117ee24: 48 f7 c1 fc ff ff ff test rcx,0xfffffffffffffffc
// ffffffff8117ee2b: 0f 85 af 00 00 00 jne ffffffff8117eee0 <-- jump taken
// [...]
// ffffffff8117eee0: 49 c7 c4 ea ff ff ff mov r12,0xffffffffffffffea
// ffffffff8117eee7: 5b pop rbx
// ffffffff8117eee8: 5d pop rbp
// ffffffff8117eee9: 4c 89 e0 mov rax,r12
// ffffffff8117eeec: 41 5c pop r12
// ffffffff8117eeee: c3 ret
545: (18) r1 = map[id:4]
547: (bf) r2 = r7
548: (b7) r3 = 0
549: (b7) r4 = 4
550: (85) call bpf_ringbuf_output#194288
// instruction 551 inserted by verifier \
551: (7a) *(u64 *)(r10 -16) = 0 | /both/ are now slow stores here
// storing map value pointer r7 at fp-16 | since value of r10 is "slow".
552: (7b) *(u64 *)(r10 -16) = r7 /
// following "fast" read to the same memory location, but due to dependency
// misprediction it will speculatively execute before insn 551/552 completes.
553: (79) r2 = *(u64 *)(r9 -16)
// in speculative domain contains attacker controlled r2. in non-speculative
// domain this contains r7, and thus accesses r7 +0 below.
554: (71) r3 = *(u8 *)(r2 +0)
// leak r3
As can be seen, the current speculative store bypass mitigation which the
verifier inserts at line 551 is insufficient since /both/, the write of
the zero sanitation as well as the map value pointer are a high latency
instruction due to prior memory access via push/pop of r10 (rbp) in contrast
to the low latency read in line 553 as r9 (r15) which stays in hardware
registers. Thus, architecturally, fp-16 is r7, however, microarchitecturally,
fp-16 can still be r2.
Initial thoughts to address this issue was to track spilled pointer loads
from stack and enforce their load via LDX through r10 as well so that /both/
the preemptive store of zero /as well as/ the load use the /same/ register
such that a dependency is created between the store and load. However, this
option is not sufficient either since it can be bypassed as well under
speculation. An updated attack with pointer spill/fills now _all_ based on
r10 would look as follows:
[...]
// r2 = oob address (e.g. scalar)
// r7 = pointer to map value
[...]
// longer store forward prediction training sequence than before.
2062: (61) r0 = *(u32 *)(r7 +25588)
2063: (63) *(u32 *)(r7 +30708) = r0
2064: (61) r0 = *(u32 *)(r7 +25592)
2065: (63) *(u32 *)(r7 +30712) = r0
2066: (61) r0 = *(u32 *)(r7 +25596)
2067: (63) *(u32 *)(r7 +30716) = r0
// store the speculative load address (scalar) this time after the store
// forward prediction training.
2068: (7b) *(u64 *)(r10 -16) = r2
// preoccupy the CPU store port by running sequence of dummy stores.
2069: (63) *(u32 *)(r7 +29696) = r0
2070: (63) *(u32 *)(r7 +29700) = r0
2071: (63) *(u32 *)(r7 +29704) = r0
2072: (63) *(u32 *)(r7 +29708) = r0
2073: (63) *(u32 *)(r7 +29712) = r0
2074: (63) *(u32 *)(r7 +29716) = r0
2075: (63) *(u32 *)(r7 +29720) = r0
2076: (63) *(u32 *)(r7 +29724) = r0
2077: (63) *(u32 *)(r7 +29728) = r0
2078: (63) *(u32 *)(r7 +29732) = r0
2079: (63) *(u32 *)(r7 +29736) = r0
2080: (63) *(u32 *)(r7 +29740) = r0
2081: (63) *(u32 *)(r7 +29744) = r0
2082: (63) *(u32 *)(r7 +29748) = r0
2083: (63) *(u32 *)(r7 +29752) = r0
2084: (63) *(u32 *)(r7 +29756) = r0
2085: (63) *(u32 *)(r7 +29760) = r0
2086: (63) *(u32 *)(r7 +29764) = r0
2087: (63) *(u32 *)(r7 +29768) = r0
2088: (63) *(u32 *)(r7 +29772) = r0
2089: (63) *(u32 *)(r7 +29776) = r0
2090: (63) *(u32 *)(r7 +29780) = r0
2091: (63) *(u32 *)(r7 +29784) = r0
2092: (63) *(u32 *)(r7 +29788) = r0
2093: (63) *(u32 *)(r7 +29792) = r0
2094: (63) *(u32 *)(r7 +29796) = r0
2095: (63) *(u32 *)(r7 +29800) = r0
2096: (63) *(u32 *)(r7 +29804) = r0
2097: (63) *(u32 *)(r7 +29808) = r0
2098: (63) *(u32 *)(r7 +29812) = r0
// overwrite scalar with dummy pointer; same as before, also including the
// sanitation store with 0 from the current mitigation by the verifier.
2099: (7a) *(u64 *)(r10 -16) = 0 | /both/ are now slow stores here
2100: (7b) *(u64 *)(r10 -16) = r7 | since store unit is still busy.
// load from stack intended to bypass stores.
2101: (79) r2 = *(u64 *)(r10 -16)
2102: (71) r3 = *(u8 *)(r2 +0)
// leak r3
[...]
Looking at the CPU microarchitecture, the scheduler might issue loads (such
as seen in line 2101) before stores (line 2099,2100) because the load execution
units become available while the store execution unit is still busy with the
sequence of dummy stores (line 2069-2098). And so the load may use the prior
stored scalar from r2 at address r10 -16 for speculation. The updated attack
may work less reliable on CPU microarchitectures where loads and stores share
execution resources.
This concludes that the sanitizing with zero stores from af86ca4e30 ("bpf:
Prevent memory disambiguation attack") is insufficient. Moreover, the detection
of stack reuse from af86ca4e30 where previously data (STACK_MISC) has been
written to a given stack slot where a pointer value is now to be stored does
not have sufficient coverage as precondition for the mitigation either; for
several reasons outlined as follows:
1) Stack content from prior program runs could still be preserved and is
therefore not "random", best example is to split a speculative store
bypass attack between tail calls, program A would prepare and store the
oob address at a given stack slot and then tail call into program B which
does the "slow" store of a pointer to the stack with subsequent "fast"
read. From program B PoV such stack slot type is STACK_INVALID, and
therefore also must be subject to mitigation.
2) The STACK_SPILL must not be coupled to register_is_const(&stack->spilled_ptr)
condition, for example, the previous content of that memory location could
also be a pointer to map or map value. Without the fix, a speculative
store bypass is not mitigated in such precondition and can then lead to
a type confusion in the speculative domain leaking kernel memory near
these pointer types.
While brainstorming on various alternative mitigation possibilities, we also
stumbled upon a retrospective from Chrome developers [0]:
[...] For variant 4, we implemented a mitigation to zero the unused memory
of the heap prior to allocation, which cost about 1% when done concurrently
and 4% for scavenging. Variant 4 defeats everything we could think of. We
explored more mitigations for variant 4 but the threat proved to be more
pervasive and dangerous than we anticipated. For example, stack slots used
by the register allocator in the optimizing compiler could be subject to
type confusion, leading to pointer crafting. Mitigating type confusion for
stack slots alone would have required a complete redesign of the backend of
the optimizing compiler, perhaps man years of work, without a guarantee of
completeness. [...]
From BPF side, the problem space is reduced, however, options are rather
limited. One idea that has been explored was to xor-obfuscate pointer spills
to the BPF stack:
[...]
// preoccupy the CPU store port by running sequence of dummy stores.
[...]
2106: (63) *(u32 *)(r7 +29796) = r0
2107: (63) *(u32 *)(r7 +29800) = r0
2108: (63) *(u32 *)(r7 +29804) = r0
2109: (63) *(u32 *)(r7 +29808) = r0
2110: (63) *(u32 *)(r7 +29812) = r0
// overwrite scalar with dummy pointer; xored with random 'secret' value
// of 943576462 before store ...
2111: (b4) w11 = 943576462
2112: (af) r11 ^= r7
2113: (7b) *(u64 *)(r10 -16) = r11
2114: (79) r11 = *(u64 *)(r10 -16)
2115: (b4) w2 = 943576462
2116: (af) r2 ^= r11
// ... and restored with the same 'secret' value with the help of AX reg.
2117: (71) r3 = *(u8 *)(r2 +0)
[...]
While the above would not prevent speculation, it would make data leakage
infeasible by directing it to random locations. In order to be effective
and prevent type confusion under speculation, such random secret would have
to be regenerated for each store. The additional complexity involved for a
tracking mechanism that prevents jumps such that restoring spilled pointers
would not get corrupted is not worth the gain for unprivileged. Hence, the
fix in here eventually opted for emitting a non-public BPF_ST | BPF_NOSPEC
instruction which the x86 JIT translates into a lfence opcode. Inserting the
latter in between the store and load instruction is one of the mitigations
options [1]. The x86 instruction manual notes:
[...] An LFENCE that follows an instruction that stores to memory might
complete before the data being stored have become globally visible. [...]
The latter meaning that the preceding store instruction finished execution
and the store is at minimum guaranteed to be in the CPU's store queue, but
it's not guaranteed to be in that CPU's L1 cache at that point (globally
visible). The latter would only be guaranteed via sfence. So the load which
is guaranteed to execute after the lfence for that local CPU would have to
rely on store-to-load forwarding. [2], in section 2.3 on store buffers says:
[...] For every store operation that is added to the ROB, an entry is
allocated in the store buffer. This entry requires both the virtual and
physical address of the target. Only if there is no free entry in the store
buffer, the frontend stalls until there is an empty slot available in the
store buffer again. Otherwise, the CPU can immediately continue adding
subsequent instructions to the ROB and execute them out of order. On Intel
CPUs, the store buffer has up to 56 entries. [...]
One small upside on the fix is that it lifts constraints from af86ca4e30
where the sanitize_stack_off relative to r10 must be the same when coming
from different paths. The BPF_ST | BPF_NOSPEC gets emitted after a BPF_STX
or BPF_ST instruction. This happens either when we store a pointer or data
value to the BPF stack for the first time, or upon later pointer spills.
The former needs to be enforced since otherwise stale stack data could be
leaked under speculation as outlined earlier. For non-x86 JITs the BPF_ST |
BPF_NOSPEC mapping is currently optimized away, but others could emit a
speculation barrier as well if necessary. For real-world unprivileged
programs e.g. generated by LLVM, pointer spill/fill is only generated upon
register pressure and LLVM only tries to do that for pointers which are not
used often. The program main impact will be the initial BPF_ST | BPF_NOSPEC
sanitation for the STACK_INVALID case when the first write to a stack slot
occurs e.g. upon map lookup. In future we might refine ways to mitigate
the latter cost.
[0] https://arxiv.org/pdf/1902.05178.pdf
[1] https://msrc-blog.microsoft.com/2018/05/21/analysis-and-mitigation-of-speculative-store-bypass-cve-2018-3639/
[2] https://arxiv.org/pdf/1905.05725.pdf
Fixes: af86ca4e30 ("bpf: Prevent memory disambiguation attack")
Fixes: f7cf25b202 ("bpf: track spill/fill of constants")
Co-developed-by: Piotr Krysiuk <piotras@gmail.com>
Co-developed-by: Benedict Schlueter <benedict.schlueter@rub.de>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Piotr Krysiuk <piotras@gmail.com>
Signed-off-by: Benedict Schlueter <benedict.schlueter@rub.de>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5e81d1117 ]
In case of JITs, each of the JIT backends compiles the BPF nospec instruction
/either/ to a machine instruction which emits a speculation barrier /or/ to
/no/ machine instruction in case the underlying architecture is not affected
by Speculative Store Bypass or has different mitigations in place already.
This covers both x86 and (implicitly) arm64: In case of x86, we use 'lfence'
instruction for mitigation. In case of arm64, we rely on the firmware mitigation
as controlled via the ssbd kernel parameter. Whenever the mitigation is enabled,
it works for all of the kernel code with no need to provide any additional
instructions here (hence only comment in arm64 JIT). Other archs can follow
as needed. The BPF nospec instruction is specifically targeting Spectre v4
since i) we don't use a serialization barrier for the Spectre v1 case, and
ii) mitigation instructions for v1 and v4 might be different on some archs.
The BPF nospec is required for a future commit, where the BPF verifier does
annotate intermediate BPF programs with speculation barriers.
Co-developed-by: Piotr Krysiuk <piotras@gmail.com>
Co-developed-by: Benedict Schlueter <benedict.schlueter@rub.de>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Piotr Krysiuk <piotras@gmail.com>
Signed-off-by: Benedict Schlueter <benedict.schlueter@rub.de>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89fb62fde3 ]
Replace pci_enable_device() with pcim_enable_device(),
pci_disable_device() and pci_release_regions() will be
called in release automatically.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 76a16be07b ]
Replace pci_enable_device() with pcim_enable_device(),
pci_disable_device() and pci_release_regions() will be
called in release automatically.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1c2f6312c ]
The result of __dev_get_by_index() is not checked for NULL and then gets
dereferenced immediately.
Also, __dev_get_by_index() must be called while holding either RTNL lock
or @dev_base_lock, which isn't satisfied by mlx5e_hairpin_get_mdev() or
its callers. This makes the underlying hlist_for_each_entry() loop not
safe, and can have adverse effects in itself.
Fix by using dev_get_by_index() and handling nullptr return value when
ifindex device is not found. Update mlx5e_hairpin_get_mdev() callers to
check for possible PTR_ERR() result.
Fixes: 77ab67b7f0 ("net/mlx5e: Basic setup of hairpin object")
Addresses-Coverity: ("Dereference null return value")
Signed-off-by: Dima Chumak <dchumak@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b54874ef1 ]
Fix a bug when flow table is created in priority that already
has other flow tables as shown in the below diagram.
If the new flow table (FT-B) has the lowest level in the priority,
we need to connect the flow tables from the previous priority (p0)
to this new table. In addition when this flow table is destroyed
(FT-B), we need to connect the flow tables from the previous
priority (p0) to the next level flow table (FT-C) in the same
priority of the destroyed table (if exists).
---------
|root_ns|
---------
|
--------------------------------
| | |
---------- ---------- ---------
|p(prio)-x| | p-y | | p-n |
---------- ---------- ---------
| |
---------------- ------------------
|ns(e.g bypass)| |ns(e.g. kernel) |
---------------- ------------------
| | |
------- ------ ----
| p0 | | p1 | |p2|
------- ------ ----
| | \
-------- ------- ------
| FT-A | |FT-B | |FT-C|
-------- ------- ------
Fixes: f90edfd279 ("net/mlx5_core: Connect flow tables")
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7c9d2102c ]
Syzbot reported skb_over_panic() in llc_pdu_init_as_xid_cmd(). The
problem was in wrong LCC header manipulations.
Syzbot's reproducer tries to send XID packet. llc_ui_sendmsg() is
doing following steps:
1. skb allocation with size = len + header size
len is passed from userpace and header size
is 3 since addr->sllc_xid is set.
2. skb_reserve() for header_len = 3
3. filling all other space with memcpy_from_msg()
Ok, at this moment we have fully loaded skb, only headers needs to be
filled.
Then code comes to llc_sap_action_send_xid_c(). This function pushes 3
bytes for LLC PDU header and initializes it. Then comes
llc_pdu_init_as_xid_cmd(). It initalizes next 3 bytes *AFTER* LLC PDU
header and call skb_push(skb, 3). This looks wrong for 2 reasons:
1. Bytes rigth after LLC header are user data, so this function
was overwriting payload.
2. skb_push(skb, 3) call can cause skb_over_panic() since
all free space was filled in llc_ui_sendmsg(). (This can
happen is user passed 686 len: 686 + 14 (eth header) + 3 (LLC
header) = 703. SKB_DATA_ALIGN(703) = 704)
So, in this patch I added 2 new private constansts: LLC_PDU_TYPE_U_XID
and LLC_PDU_LEN_U_XID. LLC_PDU_LEN_U_XID is used to correctly reserve
header size to handle LLC + XID case. LLC_PDU_TYPE_U_XID is used by
llc_pdu_header_init() function to push 6 bytes instead of 3. And finally
I removed skb_push() call from llc_pdu_init_as_xid_cmd().
This changes should not affect other parts of LLC, since after
all steps we just transmit buffer.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-and-tested-by: syzbot+5e5a981ad7cc54c4b2b4@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e4960b3d6 ]
The error code is missing in this code scenario, add the error code
'-EINVAL' to the return value 'err'.
Eliminate the follow smatch warning:
drivers/net/ethernet/mellanox/mlx4/main.c:3538 mlx4_load_one() warn:
missing error code 'err'.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Fixes: 7ae0e400cd ("net/mlx4_core: Flexible (asymmetric) allocation of EQs and MSI-X vectors for PF/VFs")
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69f0aeb13b ]
In the existing code while changing the number of TX/RX
queues using ethtool the PF/VF interface resources are
freed and reallocated (otx2_stop and otx2_open is called)
if the device is in running state. If any resource allocation
fails in otx2_open, driver free already allocated resources
and return. But again, when the number of queues changes
as the device state still running oxt2_stop is called.
In which we try to free already freed resources leading
to driver crash.
This patch fixes the issue by setting the INTF_DOWN flag on
error and free the resources in otx2_stop only if the flag is
not set.
Fixes: 50fe6c02e5 ("octeontx2-pf: Register and handle link notifications")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <Sunil.Goutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3cf4375a09 ]
One skb's skb_shinfo frags are not writable, and they can be shared with
other skbs' like by pskb_copy(). To write the frags may cause other skb's
data crash.
So before doing en/decryption, skb_cow_data() should always be called for
a cloned or nonlinear skb if req dst is using the same sg as req src.
While at it, the likely branch can be removed, as it will be covered
by skb_cow_data().
Note that esp_input() has the same issue, and I will fix it in another
patch. tipc_aead_encrypt() doesn't have this issue, as it only processes
linear data in the unlikely branch.
Fixes: fc1b6d6de2 ("tipc: introduce TIPC encryption & authentication")
Reported-by: Shuang Li <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f07f9815b7 ]
Be sure to count the csum_none cases when csum offload is
enabled.
Fixes: 0f3154e6bc ("ionic: Add Tx and Rx handling")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 76ed8a4a00 ]
We need to count the correct Tx and/or Rx packets for dynamic
interrupt moderation, depending on which we're processing on
the queue interrupt.
Fixes: 04a834592b ("ionic: dynamic interrupt moderation")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6ff85e0a2 ]
Move the interrupt coalesce value update out of the napi
thread and into the dim_work thread and set it only when it
has actually changed.
Fixes: 04a834592b ("ionic: dynamic interrupt moderation")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 52f3456a96 ]
Syzbot reported memory leak in qrtr. The problem was in unputted
struct sock. qrtr_local_enqueue() function calls qrtr_port_lookup()
which takes sock reference if port was found. Then there is the following
check:
if (!ipc || &ipc->sk == skb->sk) {
...
return -ENODEV;
}
Since we should drop the reference before returning from this function and
ipc can be non-NULL inside this if, we should add qrtr_port_put() inside
this if.
The similar corner case is in qrtr_endpoint_post() as Manivannan
reported. In case of sock_queue_rcv_skb() failure we need to put
port reference to avoid leaking struct sock pointer.
Fixes: e04df98adf ("net: qrtr: Remove receive worker")
Fixes: bdabad3e36 ("net: Add Qualcomm IPC router")
Reported-and-tested-by: syzbot+35a511c72ea7356cdcf3@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 227adfb2b1 ]
In cases where the header straight after the tunnel header was
another ethernet header (TEB), instead of the network header,
the ECN decapsulation code would treat the ethernet header as if
it was an IP header, resulting in mishandling and possible
wrong drops or corruption of the IP header.
In this case, ECT(1) is sent, so IP_ECN_decapsulate tries to copy it to the
inner IPv4 header, and correct its checksum.
The offset of the ECT bits in an IPv4 header corresponds to the
lower 2 bits of the second octet of the destination MAC address
in the ethernet header.
The IPv4 checksum corresponds to end of the source address.
In order to reproduce:
$ ip netns add A
$ ip netns add B
$ ip -n A link add _v0 type veth peer name _v1 netns B
$ ip -n A link set _v0 up
$ ip -n A addr add dev _v0 10.254.3.1/24
$ ip -n A route add default dev _v0 scope global
$ ip -n B link set _v1 up
$ ip -n B addr add dev _v1 10.254.1.6/24
$ ip -n B route add default dev _v1 scope global
$ ip -n B link add gre1 type gretap local 10.254.1.6 remote 10.254.3.1 key 0x49000000
$ ip -n B link set gre1 up
# Now send an IPv4/GRE/Eth/IPv4 frame where the outer header has ECT(1),
# and the inner header has no ECT bits set:
$ cat send_pkt.py
#!/usr/bin/env python3
from scapy.all import *
pkt = IP(b'E\x01\x00\xa7\x00\x00\x00\x00@/`%\n\xfe\x03\x01\n\xfe\x01\x06 \x00eXI\x00'
b'\x00\x00\x18\xbe\x92\xa0\xee&\x18\xb0\x92\xa0l&\x08\x00E\x00\x00}\x8b\x85'
b'@\x00\x01\x01\xe4\xf2\x82\x82\x82\x01\x82\x82\x82\x02\x08\x00d\x11\xa6\xeb'
b'3\x1e\x1e\\xf3\\xf7`\x00\x00\x00\x00ZN\x00\x00\x00\x00\x00\x00\x10\x11\x12'
b'\x13\x14\x15\x16\x17\x18\x19\x1a\x1b\x1c\x1d\x1e\x1f !"#$%&\'()*+,-./01234'
b'56789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ')
send(pkt)
$ sudo ip netns exec B tcpdump -neqlllvi gre1 icmp & ; sleep 1
$ sudo ip netns exec A python3 send_pkt.py
In the original packet, the source/destinatio MAC addresses are
dst=18:be:92:a0:ee:26 src=18:b0:92:a0:6c:26
In the received packet, they are
dst=18:bd:92:a0:ee:26 src=18:b0:92:a0:6c:27
Thanks to Lahav Schlesinger <lschlesinger@drivenets.com> and Isaac Garzon <isaac@speed.io>
for helping me pinpoint the origin.
Fixes: b723748750 ("tunnel: Propagate ECT(1) when decapsulating as recommended by RFC6040")
Cc: David S. Miller <davem@davemloft.net>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: David Ahern <dsahern@kernel.org>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Gilad Naaman <gnaaman@drivenets.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d237a7f117 ]
The release_sock() is blocking function, it would change the state
after sleeping. In order to evaluate the stated condition outside
the socket lock context, switch to use wait_woken() instead.
Fixes: 6398e23cdb ("tipc: standardize accept routine")
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8dd60de19 ]
For implicit-connect, when it's either SYN- or SYN+, an ACK should
be sent back to the client immediately. It's not appropriate for
the client to enter established state only after receiving data
from the server.
On client side, after the SYN is sent out, tipc_wait_for_connect()
should be called to wait for the ACK if timeout is set.
This patch also restricts __tipc_sendstream() to call __sendmsg()
only when it's in TIPC_OPEN state, so that the client can program
in a single loop doing both connecting and data sending like:
for (...)
sendmsg(dest, buf);
This makes the implicit-connect more implicit.
Fixes: b97bf3fd8f ("[TIPC] Initial merge")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89ec1f0886 ]
In SW DCB mode the packets sent receive incorrect UP tags. They are
constructed correctly and put into tx_ring, but UP is later remapped by
HW on the basis of TCTUPR register contents according to Tx queue
selected, and BW used is consistent with the new UP values. This is
caused by Tx queue selection in kernel not taking into account DCB
configuration. This patch fixes the issue by implementing the
ndo_select_queue NDO callback.
Fixes: fd0a05ce74 ("i40e: transmit, receive, and NAPI")
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Imam Hassan Reza Biswas <imam.hassan.reza.biswas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71d6fdba4b ]
Make warning meaningful for the user.
Previously the trace:
"Starting FW LLDP agent failed: error: I40E_ERR_ADMIN_QUEUE_ERROR, I40E_AQ_RC_EAGAIN"
was produced when user tried to start Firmware LLDP agent,
just after it was stopped with sequence:
ethtool --set-priv-flags <dev> disable-fw-lldp on
ethtool --set-priv-flags <dev> disable-fw-lldp off
(without any delay between the commands)
At that point the firmware is still processing stop command, the behavior
is expected.
Fixes: c1041d0704 ("i40e: Missing response checks in driver when starting/stopping FW LLDP")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Imam Hassan Reza Biswas <imam.hassan.reza.biswas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65662a8dcd ]
Correct the message flow between driver and firmware when disabling
queues.
Previously in case of PF reset (due to required reinit after reconfig),
the error like: "VSI seid 397 Tx ring 60 disable timeout" could show up
occasionally. The error was not a real issue of hardware or firmware,
it was caused by wrong sequence of messages invoked by the driver.
Fixes: 41c445ff0f ("i40e: main driver core")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30a56a2b88 ]
In case the entry is evicted via garbage collection there is
delay between the timeout value and the eviction event.
This adjusts the stop value based on how much time has passed.
Fixes: b87a2f9199 ("netfilter: conntrack: add gc worker to remove timed-out entries")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6371c76e2 ]
We got the following UBSAN report on one of our testing machines:
================================================================================
UBSAN: array-index-out-of-bounds in kernel/bpf/syscall.c:2389:24
index 6 is out of range for type 'char *[6]'
CPU: 43 PID: 930921 Comm: systemd-coredum Tainted: G O 5.10.48-cloudflare-kasan-2021.7.0 #1
Hardware name: <snip>
Call Trace:
dump_stack+0x7d/0xa3
ubsan_epilogue+0x5/0x40
__ubsan_handle_out_of_bounds.cold+0x43/0x48
? seq_printf+0x17d/0x250
bpf_link_show_fdinfo+0x329/0x380
? bpf_map_value_size+0xe0/0xe0
? put_files_struct+0x20/0x2d0
? __kasan_kmalloc.constprop.0+0xc2/0xd0
seq_show+0x3f7/0x540
seq_read_iter+0x3f8/0x1040
seq_read+0x329/0x500
? seq_read_iter+0x1040/0x1040
? __fsnotify_parent+0x80/0x820
? __fsnotify_update_child_dentry_flags+0x380/0x380
vfs_read+0x123/0x460
ksys_read+0xed/0x1c0
? __x64_sys_pwrite64+0x1f0/0x1f0
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xa9
<snip>
================================================================================
================================================================================
UBSAN: object-size-mismatch in kernel/bpf/syscall.c:2384:2
From the report, we can infer that some array access in bpf_link_show_fdinfo at index 6
is out of bounds. The obvious candidate is bpf_link_type_strs[BPF_LINK_TYPE_XDP] with
BPF_LINK_TYPE_XDP == 6. It turns out that BPF_LINK_TYPE_XDP is missing from bpf_types.h
and therefore doesn't have an entry in bpf_link_type_strs:
pos: 0
flags: 02000000
mnt_id: 13
link_type: (null)
link_id: 4
prog_tag: bcf7977d3b93787c
prog_id: 4
ifindex: 1
Fixes: aa8d3a716b ("bpf, xdp: Add bpf_link-based XDP attachment API")
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210719085134.43325-2-lmb@cloudflare.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f9a5c358c8 upstream.
When we exceed the limit of BSS entries, this function will free the
new entry, however, at this time, it is the last door to access the
inputed ies, so these ies will be unreferenced objects and cause memory
leak.
Therefore we should free its ies before deallocating the new entry, beside
of dropping it from hidden_list.
Signed-off-by: Nguyen Dinh Phi <phind.uet@gmail.com>
Link: https://lore.kernel.org/r/20210628132334.851095-1-phind.uet@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e7b30d24a upstream.
There is a use after free memory corruption during module exit:
- nfcsim_exit()
- nfcsim_device_free(dev0)
- nfc_digital_unregister_device()
This iterates over command queue and frees all commands,
- dev->up = false
- nfcsim_link_shutdown()
- nfcsim_link_recv_wake()
This wakes the sleeping thread nfcsim_link_recv_skb().
- nfcsim_link_recv_skb()
Wake from wait_event_interruptible_timeout(),
call directly the deb->cb callback even though (dev->up == false),
- digital_send_cmd_complete()
Dereference of "struct digital_cmd" cmd which was freed earlier by
nfc_digital_unregister_device().
This causes memory corruption shortly after (with unrelated stack
trace):
nfc nfc0: NFC: nfcsim_recv_wq: Device is down
llcp: nfc_llcp_recv: err -19
nfc nfc1: NFC: nfcsim_recv_wq: Device is down
BUG: unable to handle page fault for address: ffffffffffffffed
Call Trace:
fsnotify+0x54b/0x5c0
__fsnotify_parent+0x1fe/0x300
? vfs_write+0x27c/0x390
vfs_write+0x27c/0x390
ksys_write+0x63/0xe0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
KASAN report:
BUG: KASAN: use-after-free in digital_send_cmd_complete+0x16/0x50
Write of size 8 at addr ffff88800a05f720 by task kworker/0:2/71
Workqueue: events nfcsim_recv_wq [nfcsim]
Call Trace:
dump_stack_lvl+0x45/0x59
print_address_description.constprop.0+0x21/0x140
? digital_send_cmd_complete+0x16/0x50
? digital_send_cmd_complete+0x16/0x50
kasan_report.cold+0x7f/0x11b
? digital_send_cmd_complete+0x16/0x50
? digital_dep_link_down+0x60/0x60
digital_send_cmd_complete+0x16/0x50
nfcsim_recv_wq+0x38f/0x3d5 [nfcsim]
? nfcsim_in_send_cmd+0x4a/0x4a [nfcsim]
? lock_is_held_type+0x98/0x110
? finish_wait+0x110/0x110
? rcu_read_lock_sched_held+0x9c/0xd0
? rcu_read_lock_bh_held+0xb0/0xb0
? lockdep_hardirqs_on_prepare+0x12e/0x1f0
This flow of calling digital_send_cmd_complete() callback on driver exit
is specific to nfcsim which implements reading and sending work queues.
Since the NFC digital device was unregistered, the callback should not
be called.
Fixes: 204bddcb50 ("NFC: nfcsim: Make use of the Digital layer")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ab189cf3a upstream.
iocg_wake_fn() open-codes wait_queue_entry removal and wakeup because it
wants the wq_entry to be always removed whether it ended up waking the
task or not. finish_wait() tests whether wq_entry needs removal without
grabbing the wait_queue lock and expects the waker to use
list_del_init_careful() after all waking operations are complete, which
iocg_wake_fn() didn't do. The operation order was wrong and the regular
list_del_init() was used.
The result is that if a waiter wakes up racing the waker, it can free pop
the wq_entry off stack before the waker is still looking at it, which can
lead to a backtrace like the following.
[7312084.588951] general protection fault, probably for non-canonical address 0x586bf4005b2b88: 0000 [#1] SMP
...
[7312084.647079] RIP: 0010:queued_spin_lock_slowpath+0x171/0x1b0
...
[7312084.858314] Call Trace:
[7312084.863548] _raw_spin_lock_irqsave+0x22/0x30
[7312084.872605] try_to_wake_up+0x4c/0x4f0
[7312084.880444] iocg_wake_fn+0x71/0x80
[7312084.887763] __wake_up_common+0x71/0x140
[7312084.895951] iocg_kick_waitq+0xe8/0x2b0
[7312084.903964] ioc_rqos_throttle+0x275/0x650
[7312084.922423] __rq_qos_throttle+0x20/0x30
[7312084.930608] blk_mq_make_request+0x120/0x650
[7312084.939490] generic_make_request+0xca/0x310
[7312084.957600] submit_bio+0x173/0x200
[7312084.981806] swap_readpage+0x15c/0x240
[7312084.989646] read_swap_cache_async+0x58/0x60
[7312084.998527] swap_cluster_readahead+0x201/0x320
[7312085.023432] swapin_readahead+0x2df/0x450
[7312085.040672] do_swap_page+0x52f/0x820
[7312085.058259] handle_mm_fault+0xa16/0x1420
[7312085.066620] do_page_fault+0x2c6/0x5c0
[7312085.074459] page_fault+0x2f/0x40
Fix it by switching to list_del_init_careful() and putting it at the end.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Rik van Riel <riel@surriel.com>
Fixes: 7caa47151a ("blkcg: implement blk-iocost")
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d47255d3f8 upstream.
This reverts commit 4192f7b576.
It is not true (as stated in the reverted commit changelog) that we never
unmap the BAR on failure; it actually does happen properly on
amdgpu_driver_load_kms() -> amdgpu_driver_unload_kms() ->
amdgpu_device_fini() error path.
What's worse, this commit actually completely breaks resource freeing on
probe failure (like e.g. failure to load microcode), as
amdgpu_driver_unload_kms() notices adev->rmmio being NULL and bails too
early, leaving all the resources that'd normally be freed in
amdgpu_acpi_fini() and amdgpu_device_fini() still hanging around, leading
to all sorts of oopses when someone tries to, for example, access the
sysfs and procfs resources which are still around while the driver is
gone.
Fixes: 4192f7b576 ("drm/amdgpu: unmap register bar on device init failure")
Reported-by: Vojtech Pavlik <vojtech@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6aade587d3 upstream.
In case when psp_init_asd_microcode() fails to load ASD microcode file,
psp_v12_0_init_microcode() tries to print the firmware filename that
failed to load before bailing out.
This is wrong because:
- the firmware filename it would want it print is an incorrect one as
psp_init_asd_microcode() and psp_v12_0_init_microcode() are loading
different filenames
- it tries to print fw_name, but that's not yet been initialized by that
time, so it prints random stack contents, e.g.
amdgpu 0000:04:00.0: Direct firmware load for amdgpu/renoir_asd.bin failed with error -2
amdgpu 0000:04:00.0: amdgpu: fail to initialize asd microcode
amdgpu 0000:04:00.0: amdgpu: psp v12.0: Failed to load firmware "\xfeTO\x8e\xff\xff"
Fix that by bailing out immediately, instead of priting the bogus error
message.
Reported-by: Vojtech Pavlik <vojtech@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b53e041d8e upstream.
[Why]
We don't check DENTIST_DISPCLK_CHG_DONE to ensure dentist
display clockis updated to target value. In some scenarios with large
display clock margin, it will deliver unfinished display clock and cause
issues like display black screen.
[How]
Checking DENTIST_DISPCLK_CHG_DONE to ensure display clock
has been update to target value before driver do other clock related
actions.
Reviewed-by: Cyr Aric <aric.cyr@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Dale Zhao <dale.zhao@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ca2350e11 upstream.
Commit 670e90924b ("HID: wacom: support named keys on older devices")
added support for sending named events from the soft buttons on the
24HDT and 27QHDT. In the process, however, it inadvertantly disabled the
touchscreen of the 24HDT and 27QHDT by default. The
`wacom_set_shared_values` function would normally enable touch by default
but because it checks the state of the non-shared `has_mute_touch_switch`
flag and `wacom_setup_touch_input_capabilities` sets the state of the
/shared/ version, touch ends up being disabled by default.
This patch sets the non-shared flag, letting `wacom_set_shared_values`
take care of copying the value over to the shared version and setting
the default touch state to "on".
Fixes: 670e90924b ("HID: wacom: support named keys on older devices")
CC: stable@vger.kernel.org # 5.4+
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 640b7ea5f8 upstream.
The memory reserved by console/PALcode or non-volatile memory is not added
to memblock.memory.
Since commit fa3354e4ea (mm: free_area_init: use maximal zone PFNs rather
than zone sizes) the initialization of the memory map relies on the
accuracy of memblock.memory to properly calculate zone sizes. The holes in
memblock.memory caused by absent regions reserved by the firmware cause
incorrect initialization of struct pages which leads to BUG() during the
initial page freeing:
BUG: Bad page state in process swapper pfn:2ffc53
page:fffffc000ecf14c0 refcount:0 mapcount:1 mapping:0000000000000000 index:0x0
flags: 0x0()
raw: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
raw: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
page dumped because: nonzero mapcount
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 5.7.0-03841-gfa3354e4ea39-dirty #26
fffffc0001b5bd68 fffffc0001b5be80 fffffc00011cd148 fffffc000ecf14c0
fffffc00019803df fffffc0001b5be80 fffffc00011ce340 fffffc000ecf14c0
0000000000000000 fffffc0001b5be80 fffffc0001b482c0 fffffc00027d6618
fffffc00027da7d0 00000000002ff97a 0000000000000000 fffffc0001b5be80
fffffc00011d1abc fffffc000ecf14c0 fffffc0002d00000 fffffc0001b5be80
fffffc0001b2350c 0000000000300000 fffffc0001b48298 fffffc0001b482c0
Trace:
[<fffffc00011cd148>] bad_page+0x168/0x1b0
[<fffffc00011ce340>] free_pcp_prepare+0x1e0/0x290
[<fffffc00011d1abc>] free_unref_page+0x2c/0xa0
[<fffffc00014ee5f0>] cmp_ex_sort+0x0/0x30
[<fffffc00014ee5f0>] cmp_ex_sort+0x0/0x30
[<fffffc000101001c>] _stext+0x1c/0x20
Fix this by registering the reserved ranges in memblock.memory.
Link: https://lore.kernel.org/lkml/20210726192311.uffqnanxw3ac5wwi@ivybridge
Fixes: fa3354e4ea ("mm: free_area_init: use maximal zone PFNs rather than zone sizes")
Reported-by: Matt Turner <mattst88@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 928150fad4 upstream.
In esd_usb2_setup_rx_urbs() MAX_RX_URBS coherent buffers are allocated
and there is nothing, that frees them:
1) In callback function the urb is resubmitted and that's all
2) In disconnect function urbs are simply killed, but URB_FREE_BUFFER
is not set (see esd_usb2_setup_rx_urbs) and this flag cannot be used
with coherent buffers.
So, all allocated buffers should be freed with usb_free_coherent()
explicitly.
Side note: This code looks like a copy-paste of other can drivers. The
same patch was applied to mcba_usb driver and it works nice with real
hardware. There is no change in functionality, only clean-up code for
coherent buffers.
Fixes: 96d8e90382 ("can: Add driver for esd CAN-USB/2 device")
Link: https://lore.kernel.org/r/b31b096926dcb35998ad0271aac4b51770ca7cc8.1627404470.git.paskripkin@gmail.com
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9969e3c5f4 upstream.
In ems_usb_start() MAX_RX_URBS coherent buffers are allocated and
there is nothing, that frees them:
1) In callback function the urb is resubmitted and that's all
2) In disconnect function urbs are simply killed, but URB_FREE_BUFFER
is not set (see ems_usb_start) and this flag cannot be used with
coherent buffers.
So, all allocated buffers should be freed with usb_free_coherent()
explicitly.
Side note: This code looks like a copy-paste of other can drivers. The
same patch was applied to mcba_usb driver and it works nice with real
hardware. There is no change in functionality, only clean-up code for
coherent buffers.
Fixes: 702171adee ("ems_usb: Added support for EMS CPC-USB/ARM7 CAN/USB interface")
Link: https://lore.kernel.org/r/59aa9fbc9a8cbf9af2bbd2f61a659c480b415800.1627404470.git.paskripkin@gmail.com
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e865f0c31 upstream.
In usb_8dev_start() MAX_RX_URBS coherent buffers are allocated and
there is nothing, that frees them:
1) In callback function the urb is resubmitted and that's all
2) In disconnect function urbs are simply killed, but URB_FREE_BUFFER
is not set (see usb_8dev_start) and this flag cannot be used with
coherent buffers.
So, all allocated buffers should be freed with usb_free_coherent()
explicitly.
Side note: This code looks like a copy-paste of other can drivers. The
same patch was applied to mcba_usb driver and it works nice with real
hardware. There is no change in functionality, only clean-up code for
coherent buffers.
Fixes: 0024d8ad16 ("can: usb_8dev: Add support for USB2CAN interface from 8 devices")
Link: https://lore.kernel.org/r/d39b458cd425a1cf7f512f340224e6e9563b07bd.1627404470.git.paskripkin@gmail.com
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc43fb69a7 upstream.
Yasushi reported, that his Microchip CAN Analyzer stopped working
since commit 91c0255717 ("can: mcba_usb: fix memory leak in
mcba_usb"). The problem was in missing urb->transfer_dma
initialization.
In my previous patch to this driver I refactored mcba_usb_start() code
to avoid leaking usb coherent buffers. To archive it, I passed local
stack variable to usb_alloc_coherent() and then saved it to private
array to correctly free all coherent buffers on ->close() call. But I
forgot to initialize urb->transfer_dma with variable passed to
usb_alloc_coherent().
All of this was causing device to not work, since dma addr 0 is not
valid and following log can be found on bug report page, which points
exactly to problem described above.
| DMAR: [DMA Write] Request device [00:14.0] PASID ffffffff fault addr 0 [fault reason 05] PTE Write access is not set
Fixes: 91c0255717 ("can: mcba_usb: fix memory leak in mcba_usb")
Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=990850
Link: https://lore.kernel.org/r/20210725103630.23864-1-paskripkin@gmail.com
Cc: linux-stable <stable@vger.kernel.org>
Reported-by: Yasushi SHOJI <yasushi.shoji@gmail.com>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Tested-by: Yasushi SHOJI <yashi@spacecubics.com>
[mkl: fixed typos in commit message - thanks Yasushi SHOJI]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9449ad33be upstream.
For punch holes in EOF blocks, fallocate used buffer write to zero the
EOF blocks in last cluster. But since ->writepage will ignore EOF
pages, those zeros will not be flushed.
This "looks" ok as commit 6bba4471f0 ("ocfs2: fix data corruption by
fallocate") will zero the EOF blocks when extend the file size, but it
isn't. The problem happened on those EOF pages, before writeback, those
pages had DIRTY flag set and all buffer_head in them also had DIRTY flag
set, when writeback run by write_cache_pages(), DIRTY flag on the page
was cleared, but DIRTY flag on the buffer_head not.
When next write happened to those EOF pages, since buffer_head already
had DIRTY flag set, it would not mark page DIRTY again. That made
writeback ignore them forever. That will cause data corruption. Even
directio write can't work because it will fail when trying to drop pages
caches before direct io, as it found the buffer_head for those pages
still had DIRTY flag set, then it will fall back to buffer io mode.
To make a summary of the issue, as writeback ingores EOF pages, once any
EOF page is generated, any write to it will only go to the page cache,
it will never be flushed to disk even file size extends and that page is
not EOF page any more. The fix is to avoid zero EOF blocks with buffer
write.
The following code snippet from qemu-img could trigger the corruption.
656 open("6b3711ae-3306-4bdd-823c-cf1c0060a095.conv.2", O_RDWR|O_DIRECT|O_CLOEXEC) = 11
...
660 fallocate(11, FALLOC_FL_KEEP_SIZE|FALLOC_FL_PUNCH_HOLE, 2275868672, 327680 <unfinished ...>
660 fallocate(11, 0, 2275868672, 327680) = 0
658 pwrite64(11, "
Link: https://lkml.kernel.org/r/20210722054923.24389-2-junxiao.bi@oracle.com
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8750f9bbda upstream.
The arguments to the KVM_CLEAR_DIRTY_LOG ioctl include a pointer,
therefore it needs a compat ioctl implementation. Otherwise,
32-bit userspace fails to invoke it on 64-bit kernels; for x86
it might work fine by chance if the padding is zero, but not
on big-endian architectures.
Reported-by: Thomas Sattler
Cc: stable@vger.kernel.org
Fixes: 2a31b9db15 ("kvm: introduce manual dirty log reprotect")
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 76b4f357d0 upstream.
KVM_MAX_VCPU_ID is the maximum vcpu-id of a guest, and not the number
of vcpu-ids. Fix array indexed by vcpu-id to have KVM_MAX_VCPU_ID+1
elements.
Note that this is currently no real problem, as KVM_MAX_VCPU_ID is
an odd number, resulting in always enough padding being available at
the end of those arrays.
Nevertheless this should be fixed in order to avoid rare problems in
case someone is using an even number for KVM_MAX_VCPU_ID.
Signed-off-by: Juergen Gross <jgross@suse.com>
Message-Id: <20210701154105.23215-2-jgross@suse.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 41a8457f3f upstream.
The current assumption that methods to read PCH FIVR attributes will
return integer, is not correct. There is no good way to return integer
as negative numbers are also valid.
These read methods return a package of integers. The first integer returns
status, which is 0 on success and any other value for failure. When the
returned status is zero, then the second integer returns the actual value.
This change fixes this issue by replacing acpi_evaluate_integer() with
acpi_evaluate_object() and use acpi_extract_package() to extract results.
Fixes: 2ce6324ead ("ACPI: DPTF: Add PCH FIVR participant driver")
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: 5.10+ <stable@vger.kernel.org> # 5.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 240246f6b9 upstream.
In compression write endio sequence, the range which the compressed_bio
writes is marked as uptodate if the last bio of the compressed (sub)bios
is completed successfully. There could be previous bio which may
have failed which is recorded in cb->errors.
Set the writeback range as uptodate only if cb->errors is zero, as opposed
to checking only the last bio's status.
Backporting notes: in all versions up to 4.4 the last argument is always
replaced by "!cb->errors".
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2a6166768 upstream.
When removing a writeable device in __btrfs_free_extra_devids, the rw
device count should be decremented.
This error was caught by Syzbot which reported a warning in
close_fs_devices:
WARNING: CPU: 1 PID: 9355 at fs/btrfs/volumes.c:1168 close_fs_devices+0x763/0x880 fs/btrfs/volumes.c:1168
Modules linked in:
CPU: 0 PID: 9355 Comm: syz-executor552 Not tainted 5.13.0-rc1-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:close_fs_devices+0x763/0x880 fs/btrfs/volumes.c:1168
RSP: 0018:ffffc9000333f2f0 EFLAGS: 00010293
RAX: ffffffff8365f5c3 RBX: 0000000000000001 RCX: ffff888029afd4c0
RDX: 0000000000000000 RSI: 0000000000000001 RDI: 0000000000000000
RBP: ffff88802846f508 R08: ffffffff8365f525 R09: ffffed100337d128
R10: ffffed100337d128 R11: 0000000000000000 R12: dffffc0000000000
R13: ffff888019be8868 R14: 1ffff1100337d10d R15: 1ffff1100337d10a
FS: 00007f6f53828700(0000) GS:ffff8880b9a00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000000047c410 CR3: 00000000302a6000 CR4: 00000000001506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
btrfs_close_devices+0xc9/0x450 fs/btrfs/volumes.c:1180
open_ctree+0x8e1/0x3968 fs/btrfs/disk-io.c:3693
btrfs_fill_super fs/btrfs/super.c:1382 [inline]
btrfs_mount_root+0xac5/0xc60 fs/btrfs/super.c:1749
legacy_get_tree+0xea/0x180 fs/fs_context.c:592
vfs_get_tree+0x86/0x270 fs/super.c:1498
fc_mount fs/namespace.c:993 [inline]
vfs_kern_mount+0xc9/0x160 fs/namespace.c:1023
btrfs_mount+0x3d3/0xb50 fs/btrfs/super.c:1809
legacy_get_tree+0xea/0x180 fs/fs_context.c:592
vfs_get_tree+0x86/0x270 fs/super.c:1498
do_new_mount fs/namespace.c:2905 [inline]
path_mount+0x196f/0x2be0 fs/namespace.c:3235
do_mount fs/namespace.c:3248 [inline]
__do_sys_mount fs/namespace.c:3456 [inline]
__se_sys_mount+0x2f9/0x3b0 fs/namespace.c:3433
do_syscall_64+0x3f/0xb0 arch/x86/entry/common.c:47
entry_SYSCALL_64_after_hwframe+0x44/0xae
Because fs_devices->rw_devices was not 0 after
closing all devices. Here is the call trace that was observed:
btrfs_mount_root():
btrfs_scan_one_device():
device_list_add(); <---------------- device added
btrfs_open_devices():
open_fs_devices():
btrfs_open_one_device(); <-------- writable device opened,
rw device count ++
btrfs_fill_super():
open_ctree():
btrfs_free_extra_devids():
__btrfs_free_extra_devids(); <--- writable device removed,
rw device count not decremented
fail_tree_roots:
btrfs_close_devices():
close_fs_devices(); <------- rw device count off by 1
As a note, prior to commit cf89af146b ("btrfs: dev-replace: fail
mount if we don't have replace item with target device"), rw_devices
was decremented on removing a writable device in
__btrfs_free_extra_devids only if the BTRFS_DEV_STATE_REPLACE_TGT bit
was not set for the device. However, this check does not need to be
reinstated as it is now redundant and incorrect.
In __btrfs_free_extra_devids, we skip removing the device if it is the
target for replacement. This is done by checking whether device->devid
== BTRFS_DEV_REPLACE_DEVID. Since BTRFS_DEV_STATE_REPLACE_TGT is set
only on the device with devid BTRFS_DEV_REPLACE_DEVID, no devices
should have the BTRFS_DEV_STATE_REPLACE_TGT bit set after the check,
and so it's redundant to test for that bit.
Additionally, following commit 82372bc816 ("Btrfs: make
the logic of source device removing more clear"), rw_devices is
incremented whenever a writeable device is added to the alloc
list (including the target device in btrfs_dev_replace_finishing), so
all removals of writable devices from the alloc list should also be
accompanied by a decrement to rw_devices.
Reported-by: syzbot+a70e2ad0879f160b9217@syzkaller.appspotmail.com
Fixes: cf89af146b ("btrfs: dev-replace: fail mount if we don't have replace item with target device")
CC: stable@vger.kernel.org # 5.10+
Tested-by: syzbot+a70e2ad0879f160b9217@syzkaller.appspotmail.com
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a34b13a88 upstream.
Since commit 1b6b26ae70 ("pipe: fix and clarify pipe write wakeup
logic") we have sanitized the pipe write logic, and would only try to
wake up readers if they needed it.
In particular, if the pipe already had data in it before the write,
there was no point in trying to wake up a reader, since any existing
readers must have been aware of the pre-existing data already. Doing
extraneous wakeups will only cause potential thundering herd problems.
However, it turns out that some Android libraries have misused the EPOLL
interface, and expected "edge triggered" be to "any new write will
trigger it". Even if there was no edge in sight.
Quoting Sandeep Patil:
"The commit 1b6b26ae70 ('pipe: fix and clarify pipe write wakeup
logic') changed pipe write logic to wakeup readers only if the pipe
was empty at the time of write. However, there are libraries that
relied upon the older behavior for notification scheme similar to
what's described in [1]
One such library 'realm-core'[2] is used by numerous Android
applications. The library uses a similar notification mechanism as GNU
Make but it never drains the pipe until it is full. When Android moved
to v5.10 kernel, all applications using this library stopped working.
The library has since been fixed[3] but it will be a while before all
applications incorporate the updated library"
Our regression rule for the kernel is that if applications break from
new behavior, it's a regression, even if it was because the application
did something patently wrong. Also note the original report [4] by
Michal Kerrisk about a test for this epoll behavior - but at that point
we didn't know of any actual broken use case.
So add the extraneous wakeup, to approximate the old behavior.
[ I say "approximate", because the exact old behavior was to do a wakeup
not for each write(), but for each pipe buffer chunk that was filled
in. The behavior introduced by this change is not that - this is just
"every write will cause a wakeup, whether necessary or not", which
seems to be sufficient for the broken library use. ]
It's worth noting that this adds the extraneous wakeup only for the
write side, while the read side still considers the "edge" to be purely
about reading enough from the pipe to allow further writes.
See commit f467a6a664 ("pipe: fix and clarify pipe read wakeup logic")
for the pipe read case, which remains that "only wake up if the pipe was
full, and we read something from it".
Link: https://lore.kernel.org/lkml/CAHk-=wjeG0q1vgzu4iJhW5juPkTsjTYmiqiMUYAebWW+0bam6w@mail.gmail.com/ [1]
Link: https://github.com/realm/realm-core [2]
Link: https://github.com/realm/realm-core/issues/4666 [3]
Link: https://lore.kernel.org/lkml/CAKgNAkjMBGeAwF=2MKK758BhxvW58wYTgYKB2V-gY1PwXxrH+Q@mail.gmail.com/ [4]
Link: https://lore.kernel.org/lkml/20210729222635.2937453-1-sspatil@android.com/
Reported-by: Sandeep Patil <sspatil@android.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f7b21a0e41 ]
Fix:
../arch/x86/include/asm/proto.h:14:30: warning: ‘struct task_struct’ declared \
inside parameter list will not be visible outside of this definition or declaration
long do_arch_prctl_64(struct task_struct *task, int option, unsigned long arg2);
^~~~~~~~~~~
.../arch/x86/include/asm/proto.h:40:34: warning: ‘struct task_struct’ declared \
inside parameter list will not be visible outside of this definition or declaration
long do_arch_prctl_common(struct task_struct *task, int option,
^~~~~~~~~~~
if linux/sched.h hasn't be included previously. This fixes a build error
when this header is used outside of the kernel tree.
[ bp: Massage commit message. ]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/b76b4be3-cf66-f6b2-9a6c-3e7ef54f9845@web.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
When backporting 0db282ba2c ("selftest: use mmap instead of
posix_memalign to allocate memory") to this stable branch, I forgot a {
breaking the build.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reduce the default CMA allocation requested by the vc4-kms-v3d-pi4 and
vc4-fkms-v3d-pi4 overlays to 320MB.
Use magic values of the form (<n>*64 - 4)MB to encode default values
of <n>*64MB, allowing these defaults to be distinguished from values
set explicitly by the user with the usual overlay parameters (e.g.
"cma-384"). Only default values will be capped if the Pi RAM is too
small or the gpu_mem setting too large for it to be viable.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Add call to v4l2_ctrl_new_fwnode_properties to read and
create the fwnode based controls.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add call to v4l2_ctrl_new_fwnode_properties to read and
create the fwnode based controls.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add call to v4l2_ctrl_new_fwnode_properties to read and
create the fwnode based controls.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add the orientation parameter to all the camera sensor overlays to
avoid libcamera complaining, and add the rotation parameter where
it hadn't been added before.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
[ Upstream commit 82a1c67554 ]
Once the new schema interrupt-controller/arm,vic.yaml is added, we get
the below warnings:
arch/arm/boot/dts/versatile-ab.dt.yaml:
intc@10140000: $nodename:0: 'intc@10140000' does not match
'^interrupt-controller(@[0-9a-f,]+)*$'
arch/arm/boot/dts/versatile-ab.dt.yaml:
intc@10140000: 'clear-mask' does not match any of the regexes
Fix the node names for the interrupt controller to conform
to the standard node name interrupt-controller@.. Also drop invalid
clear-mask property.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210701132118.759454-1-sudeep.holla@arm.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49694d14ff ]
The length variable is rather pointless given that it can be trivially
deduced from offset and size. Also the initial calculation can lead
to KASAN warnings.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Leizhen (ThunderTown) <thunder.leizhen@huawei.com>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ac1d42651 ]
The length variable is rather pointless given that it can be trivially
deduced from offset and size. Also the initial calculation can lead
to KASAN warnings.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Leizhen (ThunderTown) <thunder.leizhen@huawei.com>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9c9c6815f ]
Because the out of range assignment to bit fields
are compiler-dependant, the fields could have wrong
value.
Signed-off-by: Hyunchul Lee <hyc.lee@gmail.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bdb8742dc6 ]
SCMI message headers carry a sequence number and such field is sized to
allow for MSG_TOKEN_MAX distinct numbers; moreover zero is not really an
acceptable maximum number of pending in-flight messages.
Fix accordingly the checks performed on the value exported by transports
in scmi_desc.max_msg
Link: https://lore.kernel.org/r/20210712141833.6628-3-cristian.marussi@arm.com
Reported-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
[sudeep.holla: updated the patch title and error message]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a691f16cc ]
The scmi_linux_errmap buffer access index is supposed to depend on the
array size to prevent element out of bounds access. It uses SCMI_ERR_MAX
to check bounds but that can mismatch with the array size. It also
changes the success into -EIO though scmi_linux_errmap is never used in
case of success, it is expected to work for success case too.
It is slightly confusing code as the negative of the error code
is used as index to the buffer. Fix it by negating it at the start and
make it more readable.
Link: https://lore.kernel.org/r/20210707135028.1869642-1-sudeep.holla@arm.com
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9ab9cce93 ]
Invoking trc_del_holdout() from within trc_wait_for_one_reader() is
only a performance optimization because the RCU Tasks Trace grace-period
kthread will eventually do this within check_all_holdout_tasks_trace().
But it is not a particularly important performance optimization because
it only applies to the grace-period kthread, of which there is but one.
This commit therefore removes this invocation of trc_del_holdout() in
favor of the one in check_all_holdout_tasks_trace() in the grace-period
kthread.
Reported-by: "Xu, Yanfei" <yanfei.xu@windriver.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d10bf55d8 ]
As Yanfei pointed out, although invoking trc_del_holdout() is safe
from the viewpoint of the integrity of the holdout list itself,
the put_task_struct() invoked by trc_del_holdout() can result in
use-after-free errors due to later accesses to this task_struct structure
by the RCU Tasks Trace grace-period kthread.
This commit therefore removes this call to trc_del_holdout() from
trc_inspect_reader() in favor of the grace-period thread's existing call
to trc_del_holdout(), thus eliminating that particular class of
use-after-free errors.
Reported-by: "Xu, Yanfei" <yanfei.xu@windriver.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d11fa231c ]
The doc draft-stewart-tsvwg-sctp-ipv4-00 that restricts 198 addresses
was never published. These addresses as private addresses should be
allowed to use in SCTP.
As Michael Tuexen suggested, this patch is to move 198 addresses from
unusable to private scope.
Reported-by: Sérgio <surkamp@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0dbffbb533 ]
sk_ll_usec is read locklessly from sk_can_busy_loop()
while another thread can change its value in sock_setsockopt()
This is correct but needs annotations.
BUG: KCSAN: data-race in __skb_try_recv_datagram / sock_setsockopt
write to 0xffff88814eb5f904 of 4 bytes by task 14011 on cpu 0:
sock_setsockopt+0x1287/0x2090 net/core/sock.c:1175
__sys_setsockopt+0x14f/0x200 net/socket.c:2100
__do_sys_setsockopt net/socket.c:2115 [inline]
__se_sys_setsockopt net/socket.c:2112 [inline]
__x64_sys_setsockopt+0x62/0x70 net/socket.c:2112
do_syscall_64+0x4a/0x90 arch/x86/entry/common.c:47
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffff88814eb5f904 of 4 bytes by task 14001 on cpu 1:
sk_can_busy_loop include/net/busy_poll.h:41 [inline]
__skb_try_recv_datagram+0x14f/0x320 net/core/datagram.c:273
unix_dgram_recvmsg+0x14c/0x870 net/unix/af_unix.c:2101
unix_seqpacket_recvmsg+0x5a/0x70 net/unix/af_unix.c:2067
____sys_recvmsg+0x15d/0x310 include/linux/uio.h:244
___sys_recvmsg net/socket.c:2598 [inline]
do_recvmmsg+0x35c/0x9f0 net/socket.c:2692
__sys_recvmmsg net/socket.c:2771 [inline]
__do_sys_recvmmsg net/socket.c:2794 [inline]
__se_sys_recvmmsg net/socket.c:2787 [inline]
__x64_sys_recvmmsg+0xcf/0x150 net/socket.c:2787
do_syscall_64+0x4a/0x90 arch/x86/entry/common.c:47
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0x00000000 -> 0x00000101
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 14001 Comm: syz-executor.3 Not tainted 5.13.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1e7107c5ef upstream.
Richard reported sporadic (roughly one in 10 or so) null dereferences and
other strange behaviour for a set of automated LTP tests. Things like:
BUG: kernel NULL pointer dereference, address: 0000000000000008
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 0 PID: 1516 Comm: umount Not tainted 5.10.0-yocto-standard #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-48-gd9c812dda519-prebuilt.qemu.org 04/01/2014
RIP: 0010:kernfs_sop_show_path+0x1b/0x60
...or these others:
RIP: 0010:do_mkdirat+0x6a/0xf0
RIP: 0010:d_alloc_parallel+0x98/0x510
RIP: 0010:do_readlinkat+0x86/0x120
There were other less common instances of some kind of a general scribble
but the common theme was mount and cgroup and a dubious dentry triggering
the NULL dereference. I was only able to reproduce it under qemu by
replicating Richard's setup as closely as possible - I never did get it
to happen on bare metal, even while keeping everything else the same.
In commit 71d883c37e ("cgroup_do_mount(): massage calling conventions")
we see this as a part of the overall change:
--------------
struct cgroup_subsys *ss;
- struct dentry *dentry;
[...]
- dentry = cgroup_do_mount(&cgroup_fs_type, fc->sb_flags, root,
- CGROUP_SUPER_MAGIC, ns);
[...]
- if (percpu_ref_is_dying(&root->cgrp.self.refcnt)) {
- struct super_block *sb = dentry->d_sb;
- dput(dentry);
+ ret = cgroup_do_mount(fc, CGROUP_SUPER_MAGIC, ns);
+ if (!ret && percpu_ref_is_dying(&root->cgrp.self.refcnt)) {
+ struct super_block *sb = fc->root->d_sb;
+ dput(fc->root);
deactivate_locked_super(sb);
msleep(10);
return restart_syscall();
}
--------------
In changing from the local "*dentry" variable to using fc->root, we now
export/leave that dentry pointer in the file context after doing the dput()
in the unlikely "is_dying" case. With LTP doing a crazy amount of back to
back mount/unmount [testcases/bin/cgroup_regression_5_1.sh] the unlikely
becomes slightly likely and then bad things happen.
A fix would be to not leave the stale reference in fc->root as follows:
--------------
dput(fc->root);
+ fc->root = NULL;
deactivate_locked_super(sb);
--------------
...but then we are just open-coding a duplicate of fc_drop_locked() so we
simply use that instead.
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Tejun Heo <tj@kernel.org>
Cc: Zefan Li <lizefan.x@bytedance.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: stable@vger.kernel.org # v5.1+
Reported-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Fixes: 71d883c37e ("cgroup_do_mount(): massage calling conventions")
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cbcf01128d upstream.
unix_gc() assumes that candidate sockets can never gain an external
reference (i.e. be installed into an fd) while the unix_gc_lock is
held. Except for MSG_PEEK this is guaranteed by modifying inflight
count under the unix_gc_lock.
MSG_PEEK does not touch any variable protected by unix_gc_lock (file
count is not), yet it needs to be serialized with garbage collection.
Do this by locking/unlocking unix_gc_lock:
1) increment file count
2) lock/unlock barrier to make sure incremented file count is visible
to garbage collection
3) install file into fd
This is a lock barrier (unlike smp_mb()) that ensures that garbage
collection is run completely before or completely after the barrier.
Cc: <stable@vger.kernel.org>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f62700ce63 upstream.
selftests/bpf/Makefile includes tools/scripts/Makefile.include.
With the following command
make -j60 LLVM=1 LLVM_IAS=1 <=== compile kernel
make -j60 -C tools/testing/selftests/bpf LLVM=1 LLVM_IAS=1 V=1
some files are still compiled with gcc. This patch
fixed the case if CC/AR/LD/CXX/STRIP is allowed to be
overridden, it will be written to clang/llvm-ar/..., instead of
gcc binaries. The definition of CC_NO_CLANG is also relocated
to the place after the above CC is defined.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210413153419.3028165-1-yhs@fb.com
Cc: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9615fe36b3 upstream.
We will fail to build with CONFIG_SKB_EXTENSIONS disabled after
8550ff8d8c ("skbuff: Release nfct refcount on napi stolen or re-used
skbs") since there is an unconditionally use of skb_ext_find() without
an appropriate stub. Simply build the code conditionally and properly
guard against both COFNIG_SKB_EXTENSIONS as well as
CONFIG_NET_TC_SKB_EXT being disabled.
Fixes: Fixes: 8550ff8d8c ("skbuff: Release nfct refcount on napi stolen or re-used skbs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 788bc000d4 ]
Commit 99ba0ea616 ("sfc: adjust efx->xdp_tx_queue_count with the real
number of initialized queues") intended to fix a problem caused by a
round up when calculating the number of XDP channels and queues.
However, this was not the real problem. The real problem was that the
number of XDP TX queues had been reduced to half in
commit e26ca4b535 ("sfc: reduce the number of requested xdp ev queues"),
but the variable xdp_tx_queue_count had remained the same.
Once the correct number of XDP TX queues is created again in the
previous patch of this series, this also can be reverted since the error
doesn't actually exist.
Only in the case that there is a bug in the code we can have different
values in xdp_queue_number and efx->xdp_tx_queue_count. Because of this,
and per Edward Cree's suggestion, I add instead a WARN_ON to catch if it
happens again in the future.
Note that the number of allocated queues can be higher than the number
of used ones due to the round up, as explained in the existing comment
in the code. That's why we also have to stop increasing xdp_queue_number
beyond efx->xdp_tx_queue_count.
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c90b4503cc upstream.
d3_entered flag is used to mark for vgpu_reset a previous power
transition from D3->D0, typically for VM resume from S3, so that gvt
could skip PPGTT invalidation in current vgpu_reset during resuming.
In case S0ix exit, although there is D3->D0, guest driver continue to
use vgpu as normal, with d3_entered set, until next shutdown/reboot or
power transition.
If a reboot follows a S0ix exit, device power state transite as:
D0->D3->D0->D0(reboot), while system power state transites as:
S0->S0 (reboot). There is no vgpu_reset until D0(reboot), thus
d3_entered won't be cleared, the vgpu_reset will skip PPGTT invalidation
however those PPGTT entries are no longer valid. Err appears like:
gvt: vgpu 2: vfio_pin_pages failed for gfn 0xxxxx, ret -22
gvt: vgpu 2: fail: spt xxxx guest entry 0xxxxx type 2
gvt: vgpu 2: fail: shadow page xxxx guest entry 0xxxxx type 2.
Give gvt a chance to clear d3_entered on elsp cmd submission so that the
states before & after S0ix enter/exit are consistent.
Fixes: ba25d97757 ("drm/i915/gvt: Do not destroy ppgtt_mm during vGPU D3->D0.")
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20210707004531.4873-1-colin.xu@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b60557230 upstream.
When MSI is used by the ehci-hcd driver, it can cause lost interrupts which
results in EHCI only continuing to work due to a polling fallback. But the
reliance of polling drastically reduces performance of any I/O through EHCI.
Interrupts are lost as the EHCI interrupt handler does not safely handle
edge-triggered interrupts. It fails to ensure all interrupt status bits are
cleared, which works with level-triggered interrupts but not the
edge-triggered interrupts typical from using MSI.
To fix this problem, check if the driver may have raced with the hardware
setting additional interrupt status bits and clear status until it is in a
stable state.
Fixes: 306c54d0ed ("usb: hcd: Try MSI interrupts on PCI devices")
Tested-by: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: David Jeffery <djeffery@redhat.com>
Link: https://lore.kernel.org/r/20210715213744.GA44506@redhat
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8550ff8d8c upstream.
When multiple SKBs are merged to a new skb under napi GRO,
or SKB is re-used by napi, if nfct was set for them in the
driver, it will not be released while freeing their stolen
head state or on re-use.
Release nfct on napi's stolen or re-used SKBs, and
in gro_list_prepare, check conntrack metadata diff.
Fixes: 5c6b946047 ("net/mlx5e: CT: Handle misses after executing CT action")
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b69874f74 upstream.
The commit 9a5605505d (" bonding: Add struct bond_ipesc to manage SA") is causing
following build error when XFRM is not selected in kernel config.
lld: error: undefined symbol: xfrm_dev_state_flush
>>> referenced by bond_main.c:3453 (drivers/net/bonding/bond_main.c:3453)
>>> net/bonding/bond_main.o:(bond_netdev_event) in archive drivers/built-in.a
Fixes: 9a5605505d (" bonding: Add struct bond_ipesc to manage SA")
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
CC: Taehee Yoo <ap420073@gmail.com>
CC: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 953b0dcbe2 upstream.
Commit bf3504cea7 ("net: dsa: mv88e6xxx: Add 6390 family PCS
registers to ethtool -d") added support for dumping SerDes PCS registers
via ethtool -d for Peridot.
The same implementation is also valid for Topaz, but was not
enabled at the time.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: bf3504cea7 ("net: dsa: mv88e6xxx: Add 6390 family PCS registers to ethtool -d")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a03b98d683 upstream.
Commit 0df9528736 ("mv88e6xxx: Add serdes Rx statistics") added
support for RX statistics on SerDes ports for Peridot.
This same implementation is also valid for Topaz, but was not enabled
at the time.
We need to use the generic .serdes_get_lane() method instead of the
Peridot specific one in the stats methods so that on Topaz the proper
one is used.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: 0df9528736 ("mv88e6xxx: Add serdes Rx statistics")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3abab27c32 upstream.
drm: Return -ENOTTY for non-drm ioctls
Return -ENOTTY from drm_ioctl() when userspace passes in a cmd number
which doesn't relate to the drm subsystem.
Glibc uses the TCGETS ioctl to implement isatty(), and without this
change isatty() returns it incorrectly returns true for drm devices.
To test run this command:
$ if [ -t 0 ]; then echo is a tty; fi < /dev/dri/card0
which shows "is a tty" without this patch.
This may also modify memory which the userspace application is not
expecting.
Signed-off-by: Charles Baylis <cb-kernel@fishzet.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/YPG3IBlzaMhfPqCr@stando.fishzet.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c36748ac54 upstream.
We need to append device id even if eeprom have a label property set as some
platform can have multiple eeproms with same label and we can not register
each of those with same label. Failing to register those eeproms trigger
cascade failures on such platform (system is no longer working).
This fix regression on such platform introduced with 4e302c3b56
Reported-by: Alexander Fomichev <fomichev.ru@gmail.com>
Fixes: 4e302c3b56 ("misc: eeprom: at24: fix NVMEM name with custom AT24 device name")
Cc: stable@vger.kernel.org
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8798d070d4 upstream.
Skipping the "lock has been released" notification if the lock owner
is not what we expect based on owner_cid can lead to I/O hangs.
One example is our own notifications: because owner_cid is cleared
in rbd_unlock(), when we get our own notification it is processed as
unexpected/duplicate and maybe_kick_acquire() isn't called. If a peer
that requested the lock then doesn't go through with acquiring it,
I/O requests that came in while the lock was being quiesced would
be stalled until another I/O request is submitted and kicks acquire
from rbd_img_exclusive_lock().
This makes the comment in rbd_release_lock() actually true: prior to
this change the canceled work was being requeued in response to the
"lock has been acquired" notification from rbd_handle_acquired_lock().
Cc: stable@vger.kernel.org # 5.3+
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Tested-by: Robin Geuze <robin.geuze@nl.team.blue>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed9eb71085 upstream.
Currently rbd_quiesce_lock() holds lock_rwsem for read while blocking
on releasing_wait completion. On the I/O completion side, each image
request also needs to take lock_rwsem for read. Because rw_semaphore
implementation doesn't allow new readers after a writer has indicated
interest in the lock, this can result in a deadlock if something that
needs to take lock_rwsem for write gets involved. For example:
1. watch error occurs
2. rbd_watch_errcb() takes lock_rwsem for write, clears owner_cid and
releases lock_rwsem
3. after reestablishing the watch, rbd_reregister_watch() takes
lock_rwsem for write and calls rbd_reacquire_lock()
4. rbd_quiesce_lock() downgrades lock_rwsem to for read and blocks on
releasing_wait until running_list becomes empty
5. another watch error occurs
6. rbd_watch_errcb() blocks trying to take lock_rwsem for write
7. no in-flight image request can complete and delete itself from
running_list because lock_rwsem won't be granted anymore
A similar scenario can occur with "lock has been acquired" and "lock
has been released" notification handers which also take lock_rwsem for
write to update owner_cid.
We don't actually get anything useful from sitting on lock_rwsem in
rbd_quiesce_lock() -- owner_cid updates certainly don't need to be
synchronized with. In fact the whole owner_cid tracking logic could
probably be removed from the kernel client because we don't support
proxied maintenance operations.
Cc: stable@vger.kernel.org # 5.3+
URL: https://tracker.ceph.com/issues/42757
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Tested-by: Robin Geuze <robin.geuze@nl.team.blue>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 79e482e9c3 upstream.
Commit b10d6bca87 ("arch, drivers: replace for_each_membock() with
for_each_mem_range()") didn't take into account that when there is
movable_node parameter in the kernel command line, for_each_mem_range()
would skip ranges marked with MEMBLOCK_HOTPLUG.
The page table setup code in POWER uses for_each_mem_range() to create
the linear mapping of the physical memory and since the regions marked
as MEMORY_HOTPLUG are skipped, they never make it to the linear map.
A later access to the memory in those ranges will fail:
BUG: Unable to handle kernel data access on write at 0xc000000400000000
Faulting instruction address: 0xc00000000008a3c0
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Radix SMP NR_CPUS=2048 NUMA pSeries
Modules linked in:
CPU: 0 PID: 53 Comm: kworker/u2:0 Not tainted 5.13.0 #7
NIP: c00000000008a3c0 LR: c0000000003c1ed8 CTR: 0000000000000040
REGS: c000000008a57770 TRAP: 0300 Not tainted (5.13.0)
MSR: 8000000002009033 <SF,VEC,EE,ME,IR,DR,RI,LE> CR: 84222202 XER: 20040000
CFAR: c0000000003c1ed4 DAR: c000000400000000 DSISR: 42000000 IRQMASK: 0
GPR00: c0000000003c1ed8 c000000008a57a10 c0000000019da700 c000000400000000
GPR04: 0000000000000280 0000000000000180 0000000000000400 0000000000000200
GPR08: 0000000000000100 0000000000000080 0000000000000040 0000000000000300
GPR12: 0000000000000380 c000000001bc0000 c0000000001660c8 c000000006337e00
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: 0000000040000000 0000000020000000 c000000001a81990 c000000008c30000
GPR24: c000000008c20000 c000000001a81998 000fffffffff0000 c000000001a819a0
GPR28: c000000001a81908 c00c000001000000 c000000008c40000 c000000008a64680
NIP clear_user_page+0x50/0x80
LR __handle_mm_fault+0xc88/0x1910
Call Trace:
__handle_mm_fault+0xc44/0x1910 (unreliable)
handle_mm_fault+0x130/0x2a0
__get_user_pages+0x248/0x610
__get_user_pages_remote+0x12c/0x3e0
get_arg_page+0x54/0xf0
copy_string_kernel+0x11c/0x210
kernel_execve+0x16c/0x220
call_usermodehelper_exec_async+0x1b0/0x2f0
ret_from_kernel_thread+0x5c/0x70
Instruction dump:
79280fa4 79271764 79261f24 794ae8e2 7ca94214 7d683a14 7c893a14 7d893050
7d4903a6 60000000 60000000 60000000 <7c001fec> 7c091fec 7c081fec 7c051fec
---[ end trace 490b8c67e6075e09 ]---
Making for_each_mem_range() include MEMBLOCK_HOTPLUG regions in the
traversal fixes this issue.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1976100
Link: https://lkml.kernel.org/r/20210712071132.20902-1-rppt@kernel.org
Fixes: b10d6bca87 ("arch, drivers: replace for_each_membock() with for_each_mem_range()")
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Tested-by: Greg Kurz <groug@kaod.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: <stable@vger.kernel.org> [5.10+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e71e2ace57 upstream.
Patch series "userfaultfd: do not untag user pointers", v5.
If a user program uses userfaultfd on ranges of heap memory, it may end
up passing a tagged pointer to the kernel in the range.start field of
the UFFDIO_REGISTER ioctl. This can happen when using an MTE-capable
allocator, or on Android if using the Tagged Pointers feature for MTE
readiness [1].
When a fault subsequently occurs, the tag is stripped from the fault
address returned to the application in the fault.address field of struct
uffd_msg. However, from the application's perspective, the tagged
address *is* the memory address, so if the application is unaware of
memory tags, it may get confused by receiving an address that is, from
its point of view, outside of the bounds of the allocation. We observed
this behavior in the kselftest for userfaultfd [2] but other
applications could have the same problem.
Address this by not untagging pointers passed to the userfaultfd ioctls.
Instead, let the system call fail. Also change the kselftest to use
mmap so that it doesn't encounter this problem.
[1] https://source.android.com/devices/tech/debug/tagged-pointers
[2] tools/testing/selftests/vm/userfaultfd.c
This patch (of 2):
Do not untag pointers passed to the userfaultfd ioctls. Instead, let
the system call fail. This will provide an early indication of problems
with tag-unaware userspace code instead of letting the code get confused
later, and is consistent with how we decided to handle brk/mmap/mremap
in commit dcde237319 ("mm: Avoid creating virtual address aliases in
brk()/mmap()/mremap()"), as well as being consistent with the existing
tagged address ABI documentation relating to how ioctl arguments are
handled.
The code change is a revert of commit 7d0325749a ("userfaultfd: untag
user pointers") plus some fixups to some additional calls to
validate_range that have appeared since then.
[1] https://source.android.com/devices/tech/debug/tagged-pointers
[2] tools/testing/selftests/vm/userfaultfd.c
Link: https://lkml.kernel.org/r/20210714195437.118982-1-pcc@google.com
Link: https://lkml.kernel.org/r/20210714195437.118982-2-pcc@google.com
Link: https://linux-review.googlesource.com/id/I761aa9f0344454c482b83fcfcce547db0a25501b
Fixes: 63f0c60379 ("arm64: Introduce prctl() options to control the tagged user addresses ABI")
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Alistair Delva <adelva@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Dave Martin <Dave.Martin@arm.com>
Cc: Evgenii Stepanov <eugenis@google.com>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: Mitch Phillips <mitchp@google.com>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: William McVicker <willmcvicker@google.com>
Cc: <stable@vger.kernel.org> [5.4]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46fee9ab02 upstream.
__io_queue_proc() can enqueue both poll entries and still fail
afterwards, so the callers trying to cancel it should also try to remove
the second poll entry (if any).
For example, it may leave the request alive referencing a io_uring
context but not accessible for cancellation:
[ 282.599913][ T1620] task:iou-sqp-23145 state:D stack:28720 pid:23155 ppid: 8844 flags:0x00004004
[ 282.609927][ T1620] Call Trace:
[ 282.613711][ T1620] __schedule+0x93a/0x26f0
[ 282.634647][ T1620] schedule+0xd3/0x270
[ 282.638874][ T1620] io_uring_cancel_generic+0x54d/0x890
[ 282.660346][ T1620] io_sq_thread+0xaac/0x1250
[ 282.696394][ T1620] ret_from_fork+0x1f/0x30
Cc: stable@vger.kernel.org
Fixes: 18bceab101 ("io_uring: allow POLL_ADD with double poll_wait() users")
Reported-and-tested-by: syzbot+ac957324022b7132accf@syzkaller.appspotmail.com
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/0ec1228fc5eda4cb524eeda857da8efdc43c331c.1626774457.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a3402d93c upstream.
Since the process wide cputime counter is started locklessly from
posix_cpu_timer_rearm(), it can be concurrently stopped by operations
on other timers from the same thread group, such as in the following
unlucky scenario:
CPU 0 CPU 1
----- -----
timer_settime(TIMER B)
posix_cpu_timer_rearm(TIMER A)
cpu_clock_sample_group()
(pct->timers_active already true)
handle_posix_cpu_timers()
check_process_timers()
stop_process_timers()
pct->timers_active = false
arm_timer(TIMER A)
tick -> run_posix_cpu_timers()
// sees !pct->timers_active, ignore
// our TIMER A
Fix this with simply locking process wide cputime counting start and
timer arm in the same block.
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Fixes: 60f2ceaa81 ("posix-cpu-timers: Remove unnecessary locking around cpu_clock_sample_group")
Cc: stable@vger.kernel.org
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09cfae9f13 upstream.
When receiving a packet with multiple fragments, hardware may still
touch the first fragment until the entire packet has been received. The
driver therefore keeps the first fragment mapped for DMA until end of
packet has been asserted, and delays its dma_sync call until then.
The driver tries to fit multiple receive buffers on one page. When using
3K receive buffers (e.g. using Jumbo frames and legacy-rx is turned
off/build_skb is being used) on an architecture with 4K pages, the
driver allocates an order 1 compound page and uses one page per receive
buffer. To determine the correct offset for a delayed DMA sync of the
first fragment of a multi-fragment packet, the driver then cannot just
use PAGE_MASK on the DMA address but has to construct a mask based on
the actual size of the backing page.
Using PAGE_MASK in the 3K RX buffer/4K page architecture configuration
will always sync the first page of a compound page. With the SWIOTLB
enabled this can lead to corrupted packets (zeroed out first fragment,
re-used garbage from another packet) and various consequences, such as
slow/stalling data transfers and connection resets. For example, testing
on a link with MTU exceeding 3058 bytes on a host with SWIOTLB enabled
(e.g. "iommu=soft swiotlb=262144,force") TCP transfers quickly fizzle
out without this patch.
Cc: stable@vger.kernel.org
Fixes: 0c5661ecc5 ("ixgbe: fix crash in build_skb Rx code path")
Signed-off-by: Markus Boehme <markubo@amazon.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d4abca95e upstream.
Fix an 11-year old bug in ngene_command_config_free_buf() while
addressing the following warnings caught with -Warray-bounds:
arch/alpha/include/asm/string.h:22:16: warning: '__builtin_memcpy' offset [12, 16] from the object at 'com' is out of the bounds of referenced subobject 'config' with type 'unsigned char' at offset 10 [-Warray-bounds]
arch/x86/include/asm/string_32.h:182:25: warning: '__builtin_memcpy' offset [12, 16] from the object at 'com' is out of the bounds of referenced subobject 'config' with type 'unsigned char' at offset 10 [-Warray-bounds]
The problem is that the original code is trying to copy 6 bytes of
data into a one-byte size member _config_ of the wrong structue
FW_CONFIGURE_BUFFERS, in a single call to memcpy(). This causes a
legitimate compiler warning because memcpy() overruns the length
of &com.cmd.ConfigureBuffers.config. It seems that the right
structure is FW_CONFIGURE_FREE_BUFFERS, instead, because it contains
6 more members apart from the header _hdr_. Also, the name of
the function ngene_command_config_free_buf() suggests that the actual
intention is to ConfigureFreeBuffers, instead of ConfigureBuffers
(which takes place in the function ngene_command_config_buf(), above).
Fix this by enclosing those 6 members of struct FW_CONFIGURE_FREE_BUFFERS
into new struct config, and use &com.cmd.ConfigureFreeBuffers.config as
the destination address, instead of &com.cmd.ConfigureBuffers.config,
when calling memcpy().
This also helps with the ongoing efforts to globally enable
-Warray-bounds and get us closer to being able to tighten the
FORTIFY_SOURCE routines on memcpy().
Link: https://github.com/KSPP/linux/issues/109
Fixes: dae52d009f ("V4L/DVB: ngene: Initial check-in")
Cc: stable@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/linux-hardening/20210420001631.GA45456@embeddedor/
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67f0d6d988 upstream.
The "rb_per_cpu_empty()" misinterpret the condition (as not-empty) when
"head_page" and "commit_page" of "struct ring_buffer_per_cpu" points to
the same buffer page, whose "buffer_data_page" is empty and "read" field
is non-zero.
An error scenario could be constructed as followed (kernel perspective):
1. All pages in the buffer has been accessed by reader(s) so that all of
them will have non-zero "read" field.
2. Read and clear all buffer pages so that "rb_num_of_entries()" will
return 0 rendering there's no more data to read. It is also required
that the "read_page", "commit_page" and "tail_page" points to the same
page, while "head_page" is the next page of them.
3. Invoke "ring_buffer_lock_reserve()" with large enough "length"
so that it shot pass the end of current tail buffer page. Now the
"head_page", "commit_page" and "tail_page" points to the same page.
4. Discard current event with "ring_buffer_discard_commit()", so that
"head_page", "commit_page" and "tail_page" points to a page whose buffer
data page is now empty.
When the error scenario has been constructed, "tracing_read_pipe" will
be trapped inside a deadloop: "trace_empty()" returns 0 since
"rb_per_cpu_empty()" returns 0 when it hits the CPU containing such
constructed ring buffer. Then "trace_find_next_entry_inc()" always
return NULL since "rb_num_of_entries()" reports there's no more entry
to read. Finally "trace_seq_to_user()" returns "-EBUSY" spanking
"tracing_read_pipe" back to the start of the "waitagain" loop.
I've also written a proof-of-concept script to construct the scenario
and trigger the bug automatically, you can use it to trace and validate
my reasoning above:
https://github.com/aegistudio/RingBufferDetonator.git
Tests has been carried out on linux kernel 5.14-rc2
(2734d6c1b1), my fixed version
of kernel (for testing whether my update fixes the bug) and
some older kernels (for range of affected kernels). Test result is
also attached to the proof-of-concept repository.
Link: https://lore.kernel.org/linux-trace-devel/YPaNxsIlb2yjSi5Y@aegistudio/
Link: https://lore.kernel.org/linux-trace-devel/YPgrN85WL9VyrZ55@aegistudio
Cc: stable@vger.kernel.org
Fixes: bf41a158ca ("ring-buffer: make reentrant")
Suggested-by: Linus Torvalds <torvalds@linuxfoundation.org>
Signed-off-by: Haoran Luo <www@aegistudio.net>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e3bac71c5 upstream.
Currently the histogram logic allows the user to write "cpu" in as an
event field, and it will record the CPU that the event happened on.
The problem with this is that there's a lot of events that have "cpu"
as a real field, and using "cpu" as the CPU it ran on, makes it
impossible to run histograms on the "cpu" field of events.
For example, if I want to have a histogram on the count of the
workqueue_queue_work event on its cpu field, running:
># echo 'hist:keys=cpu' > events/workqueue/workqueue_queue_work/trigger
Gives a misleading and wrong result.
Change the command to "common_cpu" as no event should have "common_*"
fields as that's a reserved name for fields used by all events. And
this makes sense here as common_cpu would be a field used by all events.
Now we can even do:
># echo 'hist:keys=common_cpu,cpu if cpu < 100' > events/workqueue/workqueue_queue_work/trigger
># cat events/workqueue/workqueue_queue_work/hist
# event histogram
#
# trigger info: hist:keys=common_cpu,cpu:vals=hitcount:sort=hitcount:size=2048 if cpu < 100 [active]
#
{ common_cpu: 0, cpu: 2 } hitcount: 1
{ common_cpu: 0, cpu: 4 } hitcount: 1
{ common_cpu: 7, cpu: 7 } hitcount: 1
{ common_cpu: 0, cpu: 7 } hitcount: 1
{ common_cpu: 0, cpu: 1 } hitcount: 1
{ common_cpu: 0, cpu: 6 } hitcount: 2
{ common_cpu: 0, cpu: 5 } hitcount: 2
{ common_cpu: 1, cpu: 1 } hitcount: 4
{ common_cpu: 6, cpu: 6 } hitcount: 4
{ common_cpu: 5, cpu: 5 } hitcount: 14
{ common_cpu: 4, cpu: 4 } hitcount: 26
{ common_cpu: 0, cpu: 0 } hitcount: 39
{ common_cpu: 2, cpu: 2 } hitcount: 184
Now for backward compatibility, I added a trick. If "cpu" is used, and
the field is not found, it will fall back to "common_cpu" and work as
it did before. This way, it will still work for old programs that use
"cpu" to get the actual CPU, but if the event has a "cpu" as a field, it
will get that event's "cpu" field, which is probably what it wants
anyway.
I updated the tracefs/README to include documentation about both the
common_timestamp and the common_cpu. This way, if that text is present in
the README, then an application can know that common_cpu is supported over
just plain "cpu".
Link: https://lkml.kernel.org/r/20210721110053.26b4f641@oasis.local.home
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@vger.kernel.org
Fixes: 8b7622bf94 ("tracing: Add cpu field for hist triggers")
Reviewed-by: Tom Zanussi <zanussi@kernel.org>
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 352384d5c8 upstream.
Because of the significant overhead that retpolines pose on indirect
calls, the tracepoint code was updated to use the new "static_calls" that
can modify the running code to directly call a function instead of using
an indirect caller, and this function can be changed at runtime.
In the tracepoint code that calls all the registered callbacks that are
attached to a tracepoint, the following is done:
it_func_ptr = rcu_dereference_raw((&__tracepoint_##name)->funcs);
if (it_func_ptr) {
__data = (it_func_ptr)->data;
static_call(tp_func_##name)(__data, args);
}
If there's just a single callback, the static_call is updated to just call
that callback directly. Once another handler is added, then the static
caller is updated to call the iterator, that simply loops over all the
funcs in the array and calls each of the callbacks like the old method
using indirect calling.
The issue was discovered with a race between updating the funcs array and
updating the static_call. The funcs array was updated first and then the
static_call was updated. This is not an issue as long as the first element
in the old array is the same as the first element in the new array. But
that assumption is incorrect, because callbacks also have a priority
field, and if there's a callback added that has a higher priority than the
callback on the old array, then it will become the first callback in the
new array. This means that it is possible to call the old callback with
the new callback data element, which can cause a kernel panic.
static_call = callback1()
funcs[] = {callback1,data1};
callback2 has higher priority than callback1
CPU 1 CPU 2
----- -----
new_funcs = {callback2,data2},
{callback1,data1}
rcu_assign_pointer(tp->funcs, new_funcs);
/*
* Now tp->funcs has the new array
* but the static_call still calls callback1
*/
it_func_ptr = tp->funcs [ new_funcs ]
data = it_func_ptr->data [ data2 ]
static_call(callback1, data);
/* Now callback1 is called with
* callback2's data */
[ KERNEL PANIC ]
update_static_call(iterator);
To prevent this from happening, always switch the static_call to the
iterator before assigning the tp->funcs to the new array. The iterator will
always properly match the callback with its data.
To trigger this bug:
In one terminal:
while :; do hackbench 50; done
In another terminal
echo 1 > /sys/kernel/tracing/events/sched/sched_waking/enable
while :; do
echo 1 > /sys/kernel/tracing/set_event_pid;
sleep 0.5
echo 0 > /sys/kernel/tracing/set_event_pid;
sleep 0.5
done
And it doesn't take long to crash. This is because the set_event_pid adds
a callback to the sched_waking tracepoint with a high priority, which will
be called before the sched_waking trace event callback is called.
Note, the removal to a single callback updates the array first, before
changing the static_call to single callback, which is the proper order as
the first element in the array is the same as what the static_call is
being changed to.
Link: https://lore.kernel.org/io-uring/4ebea8f0-58c9-e571-fd30-0ce4f6f09c70@samba.org/
Cc: stable@vger.kernel.org
Fixes: d25e37d89d ("tracepoint: Optimize using static_call()")
Reported-by: Stefan Metzmacher <metze@samba.org>
tested-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2bab693a60 upstream.
kexec_load_file() relies on the memblock infrastructure to avoid
stamping over regions of memory that are essential to the survival
of the system.
However, nobody seems to agree how to flag these regions as reserved,
and (for example) EFI only publishes its reservations in /proc/iomem
for the benefit of the traditional, userspace based kexec tool.
On arm64 platforms with GICv3, this can result in the payload being
placed at the location of the LPI tables. Shock, horror!
Let's augment the EFI reservation code with a memblock_reserve() call,
protecting our dear tables from the secondary kernel invasion.
Reported-by: Moritz Fischer <mdf@kernel.org>
Tested-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 86762ad4ab upstream.
During interrupt registration, attach state is checked. If attached,
then the Type-C state is updated with typec_set_xxx functions and role
switch is set with usb_role_switch_set_role().
If the usb_role_switch parameter is error or null, the function simply
returns 0.
So, to update usb_role_switch role if a device is attached before the
irq is registered, usb_role_switch must be registered before irq
registration.
Fixes: da0cb63100 ("usb: typec: add support for STUSB160x Type-C controller family")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20210716120718.20398-2-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fecb3a171d upstream.
Because of dwc2_hsotg_ep_stop_xfr() function uses poll
mode, first need to mask GINTSTS_GOUTNAKEFF interrupt.
In Slave mode GINTSTS_GOUTNAKEFF interrupt will be
aserted only after pop OUT NAK status packet from RxFIFO.
In dwc2_hsotg_ep_sethalt() function before setting
DCTL_SGOUTNAK need to unmask GOUTNAKEFF interrupt.
Tested by USBCV CH9 and MSC tests set in Slave, BDMA and DDMA.
All tests are passed.
Fixes: a4f8277145 ("usb: dwc2: gadget: Disable enabled HW endpoint in dwc2_hsotg_ep_disable")
Fixes: 6070636c49 ("usb: dwc2: Fix Stalling a Non-Isochronous OUT EP")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/e17fad802bbcaf879e1ed6745030993abb93baf8.1626152924.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5719df243e upstream.
This driver has a potential issue which this driver is possible to
cause superfluous irqs after usb_pkt_pop() is called. So, after
the commit 3af3260528 ("usb: renesas_usbhs: fix error return
code of usbhsf_pkt_handler()") had been applied, we could observe
the following error happened when we used g_audio.
renesas_usbhs e6590000.usb: irq_ready run_error 1 : -22
To fix the issue, disable the tx or rx interrupt in usb_pkt_pop().
Fixes: 2743e7f90d ("usb: renesas_usbhs: fix the usb_pkt_pop()")
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210624122039.596528-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5fdf5c6e6 upstream.
The MAX-3421 USB driver remembers the state of the USB toggles for a
device/endpoint. To save SPI writes, this was only done when a new
device/endpoint was being used. Unfortunately, if the old device was
removed, this would cause writes to freed memory.
To fix this, a simpler scheme is used. The toggles are read from
hardware when a URB is completed, and the toggles are always written to
hardware when any URB transaction is started. This will cause a few more
SPI transactions, but no causes kernel panics.
Fixes: 2d53139f31 ("Add support for using a MAX3421E chip as a host driver.")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20210625031456.8632-1-mark.tomlinson@alliedtelesis.co.nz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1bf2761c83 upstream.
Maximum Exit Latency (MEL) value is used by host to know how much in
advance it needs to start waking up a U1/U2 suspended link in order to
service a periodic transfer in time.
Current MEL calculation only includes the time to wake up the path from
U1/U2 to U0. This is called tMEL1 in USB 3.1 section C 1.5.2
Total MEL = tMEL1 + tMEL2 +tMEL3 + tMEL4 which should additinally include:
- tMEL2 which is the time it takes for PING message to reach device
- tMEL3 time for device to process the PING and submit a PING_RESPONSE
- tMEL4 time for PING_RESPONSE to traverse back upstream to host.
Add the missing tMEL2, tMEL3 and tMEL4 to MEL calculation.
Cc: <stable@kernel.org> # v3.5
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210715150122.1995966-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b7f56fbc7 upstream.
The device initiated link power management U1/U2 states should not be
enabled in case the system exit latency plus one bus interval (125us) is
greater than the shortest service interval of any periodic endpoint.
This is the case for both U1 and U2 sytstem exit latencies and link states.
See USB 3.2 section 9.4.9 "Set Feature" for more details
Note, before this patch the host and device initiated U1/U2 lpm states
were both enabled with lpm. After this patch it's possible to end up with
only host inititated U1/U2 lpm in case the exit latencies won't allow
device initiated lpm.
If this case we still want to set the udev->usb3_lpm_ux_enabled flag so
that sysfs users can see the link may go to U1/U2.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210715150122.1995966-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9c57d3ed5 upstream.
The H_ENTER_NESTED hypercall is handled by the L0, and it is a request
by the L1 to switch the context of the vCPU over to that of its L2
guest, and return with an interrupt indication. The L1 is responsible
for switching some registers to guest context, and the L0 switches
others (including all the hypervisor privileged state).
If the L2 MSR has TM active, then the L1 is responsible for
recheckpointing the L2 TM state. Then the L1 exits to L0 via the
H_ENTER_NESTED hcall, and the L0 saves the TM state as part of the exit,
and then it recheckpoints the TM state as part of the nested entry and
finally HRFIDs into the L2 with TM active MSR. Not efficient, but about
the simplest approach for something that's horrendously complicated.
Problems arise if the L1 exits to the L0 with a TM state which does not
match the L2 TM state being requested. For example if the L1 is
transactional but the L2 MSR is non-transactional, or vice versa. The
L0's HRFID can take a TM Bad Thing interrupt and crash.
Fix this by disallowing H_ENTER_NESTED in TM[T] state entirely, and then
ensuring that if the L1 is suspended then the L2 must have TM active,
and if the L1 is not suspended then the L2 must not have TM active.
Fixes: 360cae3137 ("KVM: PPC: Book3S HV: Nested guest entry via hypercall")
Cc: stable@vger.kernel.org # v4.20+
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f62f3c2064 upstream.
The kvmppc_rtas_hcall() sets the host rtas_args.rets pointer based on
the rtas_args.nargs that was provided by the guest. That guest nargs
value is not range checked, so the guest can cause the host rets pointer
to be pointed outside the args array. The individual rtas function
handlers check the nargs and nrets values to ensure they are correct,
but if they are not, the handlers store a -3 (0xfffffffd) failure
indication in rets[0] which corrupts host memory.
Fix this by testing up front whether the guest supplied nargs and nret
would exceed the array size, and fail the hcall directly without storing
a failure indication to rets[0].
Also expand on a comment about why we kill the guest and try not to
return errors directly if we have a valid rets[0] pointer.
Fixes: 8e591cb720 ("KVM: PPC: Book3S: Add infrastructure to implement kernel-side RTAS calls")
Cc: stable@vger.kernel.org # v3.10+
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72f68bf5c7 upstream.
There's a small window where a USB 2 remote wake may be left unhandled
due to a race between hub thread and xhci port event interrupt handler.
When the resume event is detected in the xhci interrupt handler it kicks
the hub timer, which should move the port from resume to U0 once resume
has been signalled for long enough.
To keep the hub "thread" running we set a bus_state->resuming_ports flag.
This flag makes sure hub timer function kicks itself.
checking this flag was not properly protected by the spinlock. Flag was
copied to a local variable before lock was taken. The local variable was
then checked later with spinlock held.
If interrupt is handled right after copying the flag to the local variable
we end up stopping the hub thread before it can handle the USB 2 resume.
CPU0 CPU1
(hub thread) (xhci event handler)
xhci_hub_status_data()
status = bus_state->resuming_ports;
<Interrupt>
handle_port_status()
spin_lock()
bus_state->resuming_ports = 1
set_flag(HCD_FLAG_POLL_RH)
spin_unlock()
spin_lock()
if (!status)
clear_flag(HCD_FLAG_POLL_RH)
spin_unlock()
Fix this by taking the lock a bit earlier so that it covers
the resuming_ports flag copy in the hub thread
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210715150651.1996099-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0665e38731 upstream.
Commit a66d21d7db ("usb: xhci: Add support for Renesas controller with
memory") added renesas_usb_fw.mem firmware reference to xhci-pci. Thus
modinfo indicates xhci-pci.ko has "firmware: renesas_usb_fw.mem". But
the firmware is only actually used with CONFIG_USB_XHCI_PCI_RENESAS. An
unusable firmware reference can trigger safety checkers which look for
drivers with unmet firmware dependencies.
Avoid referring to renesas_usb_fw.mem in circumstances when it cannot be
loaded (when CONFIG_USB_XHCI_PCI_RENESAS isn't set).
Fixes: a66d21d7db ("usb: xhci: Add support for Renesas controller with memory")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Thelen <gthelen@google.com>
Link: https://lore.kernel.org/r/20210702071224.3673568-1-gthelen@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e2832562c upstream.
If a 32-bit application is being used with a 64-bit kernel and is using
the mmap mechanism to write data, then the SNDRV_PCM_IOCTL_SYNC_PTR
ioctl results in calling snd_pcm_ioctl_sync_ptr_compat(). Make this use
pcm_lib_apply_appl_ptr() so that the substream's ack() method, if
defined, is called.
The snd_pcm_sync_ptr() function, used in the 64-bit ioctl case, already
uses snd_pcm_ioctl_sync_ptr_compat().
Fixes: 9027c4639e ("ALSA: pcm: Call ack() whenever appl_ptr is updated")
Signed-off-by: Alan Young <consult.awy@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/c441f18c-eb2a-3bdd-299a-696ccca2de9c@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c2b951915 upstream.
SB16 CSP driver may hit potentially a typical ABBA deadlock in two
code paths:
In snd_sb_csp_stop():
spin_lock_irqsave(&p->chip->mixer_lock, flags);
spin_lock(&p->chip->reg_lock);
In snd_sb_csp_load():
spin_lock_irqsave(&p->chip->reg_lock, flags);
spin_lock(&p->chip->mixer_lock);
Also the similar pattern is seen in snd_sb_csp_start().
Although the practical impact is very small (those states aren't
triggered in the same running state and this happens only on a real
hardware, decades old ISA sound boards -- which must be very difficult
to find nowadays), it's a real scenario and has to be fixed.
This patch addresses those deadlocks by splitting the locks in
snd_sb_csp_start() and snd_sb_csp_stop() for avoiding the nested
locks.
Reported-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/7b0fcdaf-cd4f-4728-2eae-48c151a92e10@gmail.com
Link: https://lore.kernel.org/r/20210716132723.13216-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 64752a95b7 upstream.
Recently we've added a new usb_mixer element type, USB_MIXER_BESPOKEN,
but it wasn't added in the table in snd_usb_mixer_dump_cval(). This
is no big problem since each bespoken type should have its own dump
method, but it still isn't disallowed to use the standard one, so we
should cover it as well. Along with it, define the table with the
explicit array initializer for avoiding other pitfalls.
Fixes: 785b6f29a7 ("ALSA: usb-audio: scarlett2: Fix wrong resume call")
Reported-by: Pavel Machek <pavel@denx.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210714084836.1977-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 463f36c76f upstream.
The DMA code section of the decompressor must be compiled with expolines
if Spectre V2 mitigation has been enabled for the decompressed kernel.
This is required because although the decompressor's image contains
the DMA code section, it is handed over to the decompressed kernel for use.
Because the DMA code is already slow w/o expolines, use expolines always
regardless whether the decompressed kernel is using them or not. This
simplifies the DMA code by dropping the conditional compilation of
expolines.
Fixes: bf72630130 ("s390: use proper expoline sections for .dma code")
Cc: <stable@vger.kernel.org> # 5.2
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10252bae86 upstream.
There's a chance that the IDA allocated in mmc_alloc_host() is not freed
for some time because it's freed as part of a class' release function
(see mmc_host_classdev_release() where the IDA is freed). If another
thread is holding a reference to the class, then only once all balancing
device_put() calls (in turn calling kobject_put()) have been made will
the IDA be released and usable again.
Normally this isn't a problem because the kobject is released before
anything else that may want to use the same number tries to again, but
with CONFIG_DEBUG_KOBJECT_RELEASE=y and OF aliases it becomes pretty
easy to try to allocate an alias from the IDA twice while the first time
it was allocated is still pending a call to ida_simple_remove(). It's
also possible to trigger it by using CONFIG_DEBUG_KOBJECT_RELEASE and
probe defering a driver at boot that calls mmc_alloc_host() before
trying to get resources that may defer likes clks or regulators.
Instead of allocating from the IDA in this scenario, let's just skip it
if we know this is an OF alias. The number is already "claimed" and
devices that aren't using OF aliases won't try to use the claimed
numbers anyway (see mmc_first_nonreserved_index()). This should avoid
any issues with mmc_alloc_host() returning failures from the
ida_simple_get() in the case that we're using an OF alias.
Cc: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Cc: Sujit Kautkar <sujitka@chromium.org>
Reported-by: Zubin Mithra <zsm@chromium.org>
Fixes: fa2d0aa969 ("mmc: core: Allow setting slot index via device tree alias")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210623075002.1746924-3-swboyd@chromium.org
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 488968a894 ]
Remove the conditional checking for out_data_len and skipping the fallocate
if it is 0. This is wrong will actually change any legitimate the fallocate
where the entire region is unallocated into a no-op.
Additionally, before allocating the range, if FALLOC_FL_KEEP_SIZE is set then
we need to clamp the length of the fallocate region as to not extend the size of the file.
Fixes: 966a3cb7c7 ("cifs: improve fallocate emulation")
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2485bd7557 ]
We only allow sending single credit writes through the SMB2_write() synchronous
api so split this into smaller chunks.
Fixes: 966a3cb7c7 ("cifs: improve fallocate emulation")
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Reported-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d85a6f44b ]
The 4th parameter in tc_chain_notify() should be flags rather than seq.
Let's change it back correctly.
Fixes: 32a4f5ecd7 ("net: sched: introduce chain object to uapi")
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e40cba9490 ]
This simple series of commands:
ip link add br0 type bridge vlan_filtering 1
ip link set swp0 master br0
fails on sja1105 with the following error:
[ 33.439103] sja1105 spi0.1: vlan-lookup-table needs to have at least the default untagged VLAN
[ 33.447710] sja1105 spi0.1: Invalid config, cannot upload
Warning: sja1105: Failed to change VLAN Ethertype.
For context, sja1105 has 3 operating modes:
- SJA1105_VLAN_UNAWARE: the dsa_8021q_vlans are committed to hardware
- SJA1105_VLAN_FILTERING_FULL: the bridge_vlans are committed to hardware
- SJA1105_VLAN_FILTERING_BEST_EFFORT: both the dsa_8021q_vlans and the
bridge_vlans are committed to hardware
Swapping out a VLAN list and another in happens in
sja1105_build_vlan_table(), which performs a delta update procedure.
That function is called from a few places, notably from
sja1105_vlan_filtering() which is called from the
SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING handler.
The above set of 2 commands fails when run on a kernel pre-commit
8841f6e63f ("net: dsa: sja1105: make devlink property
best_effort_vlan_filtering true by default"). So the priv->vlan_state
transition that takes place is between VLAN-unaware and full VLAN
filtering. So the dsa_8021q_vlans are swapped out and the bridge_vlans
are swapped in.
So why does it fail?
Well, the bridge driver, through nbp_vlan_init(), first sets up the
SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING attribute, and only then
proceeds to call nbp_vlan_add for the default_pvid.
So when we swap out the dsa_8021q_vlans and swap in the bridge_vlans in
the SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING handler, there are no bridge
VLANs (yet). So we have wiped the VLAN table clean, and the low-level
static config checker complains of an invalid configuration. We _will_
add the bridge VLANs using the dynamic config interface, albeit later,
when nbp_vlan_add() calls us. So it is natural that it fails.
So why did it ever work?
Surprisingly, it looks like I only tested this configuration with 2
things set up in a particular way:
- a network manager that brings all ports up
- a kernel with CONFIG_VLAN_8021Q=y
It is widely known that commit ad1afb0039 ("vlan_dev: VLAN 0 should be
treated as "no vlan tag" (802.1p packet)") installs VID 0 to every net
device that comes up. DSA treats these VLANs as bridge VLANs, and
therefore, in my testing, the list of bridge_vlans was never empty.
However, if CONFIG_VLAN_8021Q is not enabled, or the port is not up when
it joins a VLAN-aware bridge, the bridge_vlans list will be temporarily
empty, and the sja1105_static_config_reload() call from
sja1105_vlan_filtering() will fail.
To fix this, the simplest thing is to keep VID 4095, the one used for
CPU-injected control packets since commit ed040abca4 ("net: dsa:
sja1105: use 4095 as the private VLAN for untagged traffic"), in the
list of bridge VLANs too, not just the list of tag_8021q VLANs. This
ensures that the list of bridge VLANs will never be empty.
Fixes: ec5ae61076 ("net: dsa: sja1105: save/restore VLANs using a delta commit method")
Reported-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 213ad73d06 ]
Multiple complaints have been raised from the TFO users on the internet
stating that the TFO blackhole logic is too aggressive and gets falsely
triggered too often.
(e.g. https://blog.apnic.net/2021/07/05/tcp-fast-open-not-so-fast/)
Considering that most middleboxes no longer drop TFO packets, we decide
to disable the blackhole logic by setting
/proc/sys/net/ipv4/tcp_fastopen_blackhole_timeout_set to 0 by default.
Fixes: cf1ef3f071 ("net/tcp_fastopen: Disable active side TFO in certain scenarios")
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58acd10092 ]
syzbot reported a call trace:
BUG: KASAN: use-after-free in sctp_auth_shkey_hold+0x22/0xa0 net/sctp/auth.c:112
Call Trace:
sctp_auth_shkey_hold+0x22/0xa0 net/sctp/auth.c:112
sctp_set_owner_w net/sctp/socket.c:131 [inline]
sctp_sendmsg_to_asoc+0x152e/0x2180 net/sctp/socket.c:1865
sctp_sendmsg+0x103b/0x1d30 net/sctp/socket.c:2027
inet_sendmsg+0x99/0xe0 net/ipv4/af_inet.c:821
sock_sendmsg_nosec net/socket.c:703 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:723
This is an use-after-free issue caused by not updating asoc->shkey after
it was replaced in the key list asoc->endpoint_shared_keys, and the old
key was freed.
This patch is to fix by also updating active_key for asoc when old key is
being replaced with a new one. Note that this issue doesn't exist in
sctp_auth_del_key_id(), as it's not allowed to delete the active_key
from the asoc.
Fixes: 1b1e0bc994 ("sctp: add refcnt support for sh_key")
Reported-by: syzbot+b774577370208727d12b@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aaeb7bb061 ]
When using Write Zeroes on a namespace that has protection
information enabled they behavior without the PRACT bit
counter-intuitive and will generally lead to validation failures
when reading the written blocks. Fix this by always setting the
PRACT bit that generates matching PI data on the fly.
Fixes: 6e02318eae ("nvme: add support for the Write Zeroes command")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e9a72f874d ]
When registering the MDIO bus for a r8169 device, we use the PCI
bus/device specifier as a (seemingly) unique device identifier.
However the very same BDF number can be used on another PCI segment,
which makes the driver fail probing:
[ 27.544136] r8169 0002:07:00.0: enabling device (0000 -> 0003)
[ 27.559734] sysfs: cannot create duplicate filename '/class/mdio_bus/r8169-700'
....
[ 27.684858] libphy: mii_bus r8169-700 failed to register
[ 27.695602] r8169: probe of 0002:07:00.0 failed with error -22
Add the segment number to the device name to make it more unique.
This fixes operation on ARM N1SDP boards, with two boards connected
together to form an SMP system, and all on-board devices showing up
twice, just on different PCI segments. A similar issue would occur on
large systems with many PCI slots and multiple RTL8169 NICs.
Fixes: f1e911d5d0 ("r8169: add basic phylib support")
Signed-off-by: Sayanta Pattanayak <sayanta.pattanayak@arm.com>
[Andre: expand commit message, use pci_domain_nr()]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c881ca0b3 ]
To quote Alexey[1]:
I was adding custom tracepoint to the kernel, grabbed full F34 kernel
.config, disabled modules and booted whole shebang as VM kernel.
Then did
perf record -a -e ...
It crashed:
general protection fault, probably for non-canonical address 0x435f5346592e4243: 0000 [#1] SMP PTI
CPU: 1 PID: 842 Comm: cat Not tainted 5.12.6+ #26
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-1.fc33 04/01/2014
RIP: 0010:t_show+0x22/0xd0
Then reproducer was narrowed to
# cat /sys/kernel/tracing/printk_formats
Original F34 kernel with modules didn't crash.
So I started to disable options and after disabling AFS everything
started working again.
The root cause is that AFS was placing char arrays content into a
section full of _pointers_ to strings with predictable consequences.
Non canonical address 435f5346592e4243 is "CB.YFS_" which came from
CM_NAME macro.
Steps to reproduce:
CONFIG_AFS=y
CONFIG_TRACING=y
# cat /sys/kernel/tracing/printk_formats
Fix this by the following means:
(1) Add enum->string translation tables in the event header with the AFS
and YFS cache/callback manager operations listed by RPC operation ID.
(2) Modify the afs_cb_call tracepoint to print the string from the
translation table rather than using the string at the afs_call name
pointer.
(3) Switch translation table depending on the service we're being accessed
as (AFS or YFS) in the tracepoint print clause. Will this cause
problems to userspace utilities?
Note that the symbolic representation of the YFS service ID isn't
available to this header, so I've put it in as a number. I'm not sure
if this is the best way to do this.
(4) Remove the name wrangling (CM_NAME) macro and put the names directly
into the afs_call_type structs in cmservice.c.
Fixes: 8e8d7f13b6 ("afs: Add some tracepoints")
Reported-by: Alexey Dobriyan (SK hynix) <adobriyan@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
cc: Andrew Morton <akpm@linux-foundation.org>
cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/r/YLAXfvZ+rObEOdc%2F@localhost.localdomain/ [1]
Link: https://lore.kernel.org/r/643721.1623754699@warthog.procyon.org.uk/
Link: https://lore.kernel.org/r/162430903582.2896199.6098150063997983353.stgit@warthog.procyon.org.uk/ # v1
Link: https://lore.kernel.org/r/162609463957.3133237.15916579353149746363.stgit@warthog.procyon.org.uk/ # v1 (repost)
Link: https://lore.kernel.org/r/162610726860.3408253.445207609466288531.stgit@warthog.procyon.org.uk/ # v2
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3a1a937f7 ]
This reverts commit 0bd860493f.
While the patch was working as stated,ie preventing the L850-GL LTE modem
from crashing on some U3 wake-ups due to a race condition between the
host wake-up and the modem-side wake-up, when using the MBIM interface,
this would force disabling the USB runtime PM on the device.
The increased power consumption is significant for LTE laptops,
and given that with decently recent modem firmwares, when the modem hits
the bug, it automatically recovers (ie it drops from the bus, but
automatically re-enumerates after less than half a second, rather than being
stuck until a power cycle as it was doing with ancient firmware), for
most people, the trade-off now seems in favor of re-enabling it by
default.
For people with access to the platform code, the bug can also be worked-around
successfully by changing the USB3 LFPM polling off-time for the XHCI
controller in the BIOS code.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Link: https://lore.kernel.org/r/20210721092516.2775971-1-vpalatin@chromium.org
Fixes: 0bd860493f ("USB: quirks: ignore remote wake-up on Fibocom L850-GL LTE modem")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdb330f4b4 ]
If MDSs aren't available while mounting a filesystem, the session state
will transition from SESSION_OPENING to SESSION_CLOSING. And in that
scenario check_session_state() will be called from delayed_work() and
trigger this WARN.
Avoid this by only WARNing after a session has already been established
(i.e., the s_ttl will be different from 0).
Fixes: 62575e270f ("ceph: check session state after bumping session->s_seq")
Signed-off-by: Luis Henriques <lhenriques@suse.de>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8fb4792f09 ]
While running the self-tests on a KASAN enabled kernel, I observed a
slab-out-of-bounds splat very similar to the one reported in
commit 821bbf79fe ("ipv6: Fix KASAN: slab-out-of-bounds Read in
fib6_nh_flush_exceptions").
We additionally need to take care of fib6_metrics initialization
failure when the caller provides an nh.
The fix is similar, explicitly free the route instead of calling
fib6_info_release on a half-initialized object.
Fixes: f88d8ea67f ("ipv6: Plumb support for nexthop object in a fib6_info")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 727d6a8b7e ]
Currently tcf_skbmod_act() assumes that packets use Ethernet as their L2
protocol, which is not always the case. As an example, for CAN devices:
$ ip link add dev vcan0 type vcan
$ ip link set up vcan0
$ tc qdisc add dev vcan0 root handle 1: htb
$ tc filter add dev vcan0 parent 1: protocol ip prio 10 \
matchall action skbmod swap mac
Doing the above silently corrupts all the packets. Do not perform skbmod
actions for non-Ethernet packets.
Fixes: 86da71b573 ("net_sched: Introduce skbmod action")
Reviewed-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Peilin Ye <peilin.ye@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bbfd4506f9 ]
Currently, VF doesn't enable rx VLAN offload when initializating,
and PF does it for VFs. If user disable the rx VLAN offload for
VF with ethtool -K, and reload the VF driver, it may cause the
rx VLAN offload state being inconsistent between hardware and
software.
Fixes it by enabling rx VLAN offload when VF initializing.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b713d14dc ]
Currently, the mailbox synchronous communication between VF and PF use
the following fields to maintain communication:
1. Origin_mbx_msg which was combined by message code and subcode, used
to match request and response.
2. Received_resp which means whether received response.
There may possible mismatches of the following situation:
1. VF sends message A with code=1 subcode=1.
2. PF was blocked about 500ms when processing the message A.
3. VF will detect message A timeout because it can't get the response
within 500ms.
4. VF sends message B with code=1 subcode=1 which equal message A.
5. PF processes the first message A and send the response message to
VF.
6. VF will identify the response matched the message B because the
code/subcode is the same. This will lead to mismatch of request and
response.
To fix the above bug, we use the following scheme:
1. The message sent from VF was labelled with match_id which was a
unique 16-bit non-zero value.
2. The response sent from PF will label with match_id which got from
the request.
3. The VF uses the match_id to match request and response message.
As for PF driver, it only needs to copy the match_id from request to
response.
Fixes: dde1a86e93 ("net: hns3: Add mailbox support to PF driver")
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f20c8adb1 ]
tfo_active_disable_stamp is read and written locklessly.
We need to annotate these accesses appropriately.
Then, we need to perform the atomic_inc(tfo_active_disable_times)
after the timestamp has been updated, and thus add barriers
to make sure tcp_fastopen_active_should_disable() wont read
a stale timestamp.
Fixes: cf1ef3f071 ("net/tcp_fastopen: Disable active side TFO in certain scenarios")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Wei Wang <weiwan@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b16f3299ae ]
Building on ARCH=arc causes a "redefined" warning, so rename this
driver's CACHE_LINE_MASK to avoid the warning.
../drivers/net/ethernet/hisilicon/hip04_eth.c:134: warning: "CACHE_LINE_MASK" redefined
134 | #define CACHE_LINE_MASK 0x3F
In file included from ../include/linux/cache.h:6,
from ../include/linux/printk.h:9,
from ../include/linux/kernel.h:19,
from ../include/linux/list.h:9,
from ../include/linux/module.h:12,
from ../drivers/net/ethernet/hisilicon/hip04_eth.c:7:
../arch/arc/include/asm/cache.h:17: note: this is the location of the previous definition
17 | #define CACHE_LINE_MASK (~(L1_CACHE_BYTES - 1))
Fixes: d413779cdd ("net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11a39259ff ]
bnxt_half_open_nic() is called during during ethtool self test and is
protected by rtnl_lock. Firmware reset can be happening at the same
time. Only critical portions of the entire firmware reset sequence
are protected by the rtnl_lock. It is possible that bnxt_half_open_nic()
can be called when the firmware reset sequence is aborting. In that
case, bnxt_half_open_nic() needs to check if the ABORT_ERR flag is set
and abort if it is. The ethtool self test will fail but the NIC will be
brought to a consistent IF_DOWN state.
Without this patch, if bnxt_half_open_nic() were to continue in this
error state, it may crash like this:
bnxt_en 0000:82:00.1 enp130s0f1np1: FW reset in progress during close, FW reset will be aborted
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
...
Process ethtool (pid: 333327, stack limit = 0x0000000046476577)
Call trace:
bnxt_alloc_mem+0x444/0xef0 [bnxt_en]
bnxt_half_open_nic+0x24/0xb8 [bnxt_en]
bnxt_self_test+0x2dc/0x390 [bnxt_en]
ethtool_self_test+0xe0/0x1f8
dev_ethtool+0x1744/0x22d0
dev_ioctl+0x190/0x3e0
sock_ioctl+0x238/0x480
do_vfs_ioctl+0xc4/0x758
ksys_ioctl+0x84/0xb8
__arm64_sys_ioctl+0x28/0x38
el0_svc_handler+0xb0/0x180
el0_svc+0x8/0xc
Fixes: a1301f08c5 ("bnxt_en: Check abort error state in bnxt_open_nic().")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 96bdd4b9ea ]
Only pass supported VLAN protocol IDs for stripped VLAN tags to the
stack. The stack will hit WARN() if the protocol ID is unsupported.
Existing firmware sets up the chip to strip 0x8100, 0x88a8, 0x9100.
Only the 1st two protocols are supported by the kernel.
Fixes: a196e96bb6 ("bnxt_en: clean up VLAN feature bit handling")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6cd657cb3e ]
In the BNXT_FW_RESET_STATE_POLL_VF state in bnxt_fw_reset_task() after all
VFs have unregistered, we need to check for BNXT_STATE_ABORT_ERR after
we acquire the rtnl_lock. If the flag is set, we need to abort.
Fixes: 230d1f0de7 ("bnxt_en: Handle firmware reset.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c9f046bc3 ]
The capabilities can change after firmware upgrade/downgrade, so we
should get the up-to-date RoCE capabilities everytime bnxt_ulp_probe()
is called.
Fixes: 2151fe0830 ("bnxt_en: Handle RESET_NOTIFY async event from firmware.")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c81cfb6256 ]
If device is already disabled in reset path and PCI io error is
detected before the device could be enabled, driver could
call pci_disable_device() for already disabled device. Fix this
problem by calling pci_disable_device() only if the device is already
enabled.
Fixes: 6316ea6db9 ("bnxt_en: Enable AER support.")
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d2cbbf1fe5 ]
During a rework of initramfs code the INITRAMFS_COMPRESSION config
option was removed in commit 65e00e04e5. A leftover as a dependency
broke the config option ACPI_TABLE_OVERRIDE_VIA_ BUILTIN_INITRD that
is used to enable the overriding of ACPI tables from built-in initrd.
Fixing the dependency.
Fixes: 65e00e04e5 ("initramfs: refactor the initramfs build rules")
Signed-off-by: Robert Richter <rrichter@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56912da7a6 ]
The original implementation of RPM handling in probe() was mostly
correct, except it failed to call pm_runtime_get_*() to activate the
hardware. The subsequent fix, 734882a8bf ("spi: cadence: Correct
initialisation of runtime PM"), breaks the implementation further,
to the point where the system using this hard IP on ZynqMP hangs on
boot, because it accesses hardware which is gated off.
Undo 734882a8bf ("spi: cadence: Correct initialisation of runtime
PM") and instead add missing pm_runtime_get_noresume() and move the
RPM disabling all the way to the end of probe(). That makes ZynqMP
not hang on boot yet again.
Fixes: 734882a8bf ("spi: cadence: Correct initialisation of runtime PM")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Charles Keepax <ckeepax@opensource.cirrus.com>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210716182133.218640-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e746f3451e ]
A ISCSI_IFACE_PARAM can have the same value as a ISCSI_NET_PARAM so when
iscsi_iface_attr_is_visible tries to figure out the type by just checking
the value, we can collide and return the wrong type. When we call into the
driver we might not match and return that we don't want attr visible in
sysfs. The patch fixes this by setting the type when we figure out what the
param is.
Link: https://lore.kernel.org/r/20210701002559.89533-1-michael.christie@oracle.com
Fixes: 3e0f65b34c ("[SCSI] iscsi_transport: Additional parameters for network settings")
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 517a16b1a8 ]
Commit 63346650c1 ("netrom: switch to sock timer API") switched to use
sock timer API. It replaces mod_timer() by sk_reset_timer(), and
del_timer() by sk_stop_timer().
Function sk_reset_timer() will increase the refcount of sock if it is
called on an inactive timer, hence, in case the timer expires, we need to
decrease the refcount ourselves in the handler, otherwise, the sock
refcount will be unbalanced and the sock will never be freed.
Signed-off-by: Nguyen Dinh Phi <phind.uet@gmail.com>
Reported-by: syzbot+10f1194569953b72f1ae@syzkaller.appspotmail.com
Fixes: 63346650c1 ("netrom: switch to sock timer API")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f3fdd8d48 ]
After commit ca84bd058d ("sctp: copy the optval from user space in
sctp_setsockopt"), it does memory allocation in sctp_setsockopt with
the optlen, and it would fail the allocation and return error if the
optlen from user space is a huge value.
This breaks some sockopts, like SCTP_HMAC_IDENT, SCTP_RESET_STREAMS and
SCTP_AUTH_KEY, as when processing these sockopts before, optlen would
be trimmed to a biggest value it needs when optlen is a huge value,
instead of failing the allocation and returning error.
This patch is to fix the allocation failure when it's a huge optlen from
user space by trimming it to the biggest size sctp sockopt may need when
necessary, and this biggest size is from sctp_setsockopt_reset_streams()
for SCTP_RESET_STREAMS, which is bigger than those for SCTP_HMAC_IDENT
and SCTP_AUTH_KEY.
Fixes: ca84bd058d ("sctp: copy the optval from user space in sctp_setsockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5051bcece ]
Syzbot reported memory leak in tcindex_set_parms(). The problem was in
non-freed perfect hash in tcindex_partial_destroy_work().
In tcindex_set_parms() new tcindex_data is allocated and some fields from
old one are copied to new one, but not the perfect hash. Since
tcindex_partial_destroy_work() is the destroy function for old
tcindex_data, we need to free perfect hash to avoid memory leak.
Reported-and-tested-by: syzbot+f0bbb2287b8993d4fa74@syzkaller.appspotmail.com
Fixes: 331b72922c ("net: sched: RCU cls_tcindex")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd31ecf44b ]
When running CPU_FTR_P9_TM_HV_ASSIST, HFSCR[TM] is set for the guest
even if the host has CONFIG_TRANSACTIONAL_MEM=n, which causes it to be
unprepared to handle guest exits while transactional.
Normal guests don't have a problem because the HTM capability will not
be advertised, but a rogue or buggy one could crash the host.
Fixes: 4bb3c7a020 ("KVM: PPC: Book3S HV: Work around transactional memory bugs in POWER9")
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210716024310.164448-1-npiggin@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f119ba1d5 ]
The release_sock() is blocking function, it would change the state
after sleeping. use wait_woken() instead.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 674a9f1f68 ]
Missing TPM final event log table is not a firmware bug.
Clearly if providing event log in the old format makes the final event
log invalid it should not be provided at least in that case.
Fixes: b4f1874c62 ("tpm: check event log version before reading final events")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 40ac971eab ]
xen-swiotlb can use vmalloc backed addresses for dma coherent allocations
and uses the common helpers. Properly handle them to unbreak Xen on
ARM platforms.
Fixes: 1b65c4e5a9 ("swiotlb-xen: use xen_alloc/free_coherent_pages")
Signed-off-by: Roman Skakun <roman_skakun@epam.com>
Reviewed-by: Andrii Anisov <andrii_anisov@epam.com>
[hch: split the patch, renamed the helpers]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 991e634360 ]
When nr_segs equal to zero in iovec_from_user, the object
msg->msg_iter.iov is uninit stack memory in caif_seqpkt_sendmsg
which is defined in ___sys_sendmsg. So we cann't just judge
msg->msg_iter.iov->base directlly. We can use nr_segs to judge
msg in caif_seqpkt_sendmsg whether has data buffers.
=====================================================
BUG: KMSAN: uninit-value in caif_seqpkt_sendmsg+0x693/0xf60 net/caif/caif_socket.c:542
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1c9/0x220 lib/dump_stack.c:118
kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:118
__msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:215
caif_seqpkt_sendmsg+0x693/0xf60 net/caif/caif_socket.c:542
sock_sendmsg_nosec net/socket.c:652 [inline]
sock_sendmsg net/socket.c:672 [inline]
____sys_sendmsg+0x12b6/0x1350 net/socket.c:2343
___sys_sendmsg net/socket.c:2397 [inline]
__sys_sendmmsg+0x808/0xc90 net/socket.c:2480
__compat_sys_sendmmsg net/compat.c:656 [inline]
Reported-by: syzbot+09a5d591c1f98cf5efcb@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?id=1ace85e8fc9b0d5a45c08c2656c3e91762daa9b8
Fixes: bece7b2398 ("caif: Rewritten socket implementation")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54ea2f49fd ]
The proc socket stats use sk_prot->inuse_idx value to record inuse sock
stats. We currently do not set this correctly from sockmap side. The
result is reading sock stats '/proc/net/sockstat' gives incorrect values.
The socket counter is incremented correctly, but because we don't set the
counter correctly when we replace sk_prot we may omit the decrement.
To get the correct inuse_idx value move the core_initcall that initializes
the UDP proto handlers to late_initcall. This way it is initialized after
UDP has the chance to assign the inuse_idx value from the register protocol
handler.
Fixes: edc6741cc6 ("bpf: Add sockmap hooks for UDP sockets")
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Cong Wang <cong.wang@bytedance.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20210714154750.528206-1-jakub@cloudflare.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 228a4a7ba8 ]
The proc socket stats use sk_prot->inuse_idx value to record inuse sock
stats. We currently do not set this correctly from sockmap side. The
result is reading sock stats '/proc/net/sockstat' gives incorrect values.
The socket counter is incremented correctly, but because we don't set the
counter correctly when we replace sk_prot we may omit the decrement.
To get the correct inuse_idx value move the core_initcall that initializes
the TCP proto handlers to late_initcall. This way it is initialized after
TCP has the chance to assign the inuse_idx value from the register protocol
handler.
Fixes: 604326b41a ("bpf, sockmap: convert to generic sk_msg interface")
Suggested-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Cong Wang <cong.wang@bytedance.com>
Link: https://lore.kernel.org/bpf/20210712195546.423990-3-john.fastabend@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9109165625 ]
Currently array jit->seen_reg[r1] is being accessed before the range
checking of index r1. The range changing on r1 should be performed
first since it will avoid any potential out-of-range accesses on the
array seen_reg[] and also it is more optimal to perform checks on r1
before fetching data from the array. Fix this by swapping the order
of the checks before the array access.
Fixes: 0546231057 ("s390/bpf: Add s390x eBPF JIT compiler backend")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Ilya Leoshkevich <iii@linux.ibm.com>
Acked-by: Ilya Leoshkevich <iii@linux.ibm.com>
Link: https://lore.kernel.org/bpf/20210715125712.24690-1-colin.king@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e7efc2ce3d ]
Shifting the u16 integer oct->pcie_port by CN23XX_PKT_INPUT_CTL_MAC_NUM_POS
(29) bits will be promoted to a 32 bit signed int and then sign-extended
to a u64. In the cases where oct->pcie_port where bit 2 is set (e.g. 3..7)
the shifted value will be sign extended and the top 32 bits of the result
will be set.
Fix this by casting the u16 values to a u64 before the 29 bit left shift.
Addresses-Coverity: ("Unintended sign extension")
Fixes: 3451b97cce ("liquidio: CN23XX register setup")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aebacb7f6c ]
31cd0e119d ("timers: Recalculate next timer interrupt only when
necessary") subtly altered get_next_timer_interrupt()'s behaviour. The
function no longer consistently returns KTIME_MAX with no timers
pending.
In order to decide if there are any timers pending we check whether the
next expiry will happen NEXT_TIMER_MAX_DELTA jiffies from now.
Unfortunately, the next expiry time and the timer base clock are no
longer updated in unison. The former changes upon certain timer
operations (enqueue, expire, detach), whereas the latter keeps track of
jiffies as they move forward. Ultimately breaking the logic above.
A simplified example:
- Upon entering get_next_timer_interrupt() with:
jiffies = 1
base->clk = 0;
base->next_expiry = NEXT_TIMER_MAX_DELTA;
'base->next_expiry == base->clk + NEXT_TIMER_MAX_DELTA', the function
returns KTIME_MAX.
- 'base->clk' is updated to the jiffies value.
- The next time we enter get_next_timer_interrupt(), taking into account
no timer operations happened:
base->clk = 1;
base->next_expiry = NEXT_TIMER_MAX_DELTA;
'base->next_expiry != base->clk + NEXT_TIMER_MAX_DELTA', the function
returns a valid expire time, which is incorrect.
This ultimately might unnecessarily rearm sched's timer on nohz_full
setups, and add latency to the system[1].
So, introduce 'base->timers_pending'[2], update it every time
'base->next_expiry' changes, and use it in get_next_timer_interrupt().
[1] See tick_nohz_stop_tick().
[2] A quick pahole check on x86_64 and arm64 shows it doesn't make
'struct timer_base' any bigger.
Fixes: 31cd0e119d ("timers: Recalculate next timer interrupt only when necessary")
Signed-off-by: Nicolas Saenz Julienne <nsaenzju@redhat.com>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c71f78a662 ]
The ALC5631 does not like multi-write accesses, avoid them. This fixes:
rt5631 4-001a: Unable to sync registers 0x3a-0x3c. -121
errors on resume from suspend (and all registers after the registers in
the error not being synced).
Inspired by commit 2d30e9494f ("ASoC: rt5651: Fix regcache sync errors
on resume") from Hans de Geode, which fixed the same errors on ALC5651.
Signed-off-by: Maxim Schwalm <maxim.schwalm@gmail.com>
Link: https://lore.kernel.org/r/20210712005011.28536-1-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c73daee4b ]
Since config.dev = pdev->dev.parent in current code, so
dev_get_drvdata(rdev->dev.parent) call in hi6421_regulator_enable
returns the drvdata of the mfd device rather than the regulator. Fix it.
This was broken while converting to use simplified DT parsing because the
config.dev changed from pdev->dev to pdev->dev.parent for parsing the
parent's of_node.
Fixes: 29dc269a85 ("regulator: hi6421: Convert to use simplified DT parsing")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20210630095959.2411543-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7999d2555c ]
Add pm_runtime calls in probe/probe error path and remove
in order to be consistent in all places in ordering and
ensure that pm_runtime is disabled prior to resources used
by the SPI controller.
This patch also fixes the 2 following warnings on driver remove:
WARNING: CPU: 0 PID: 743 at drivers/clk/clk.c:594 clk_core_disable_lock+0x18/0x24
WARNING: CPU: 0 PID: 743 at drivers/clk/clk.c:476 clk_unprepare+0x24/0x2c
Fixes: 038ac869c9 ("spi: stm32: add runtime PM support")
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://lore.kernel.org/r/1625646426-5826-2-git-send-email-alain.volmat@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0f008551f ]
The tracepoints trace_sched_stat_{wait, sleep, iowait} are not exposed to user
if CONFIG_SCHEDSTATS is not set, "perf sched record" records the three events.
As a result, the command fails.
Before:
#perf sched record sleep 1
event syntax error: 'sched:sched_stat_wait'
\___ unknown tracepoint
Error: File /sys/kernel/tracing/events/sched/sched_stat_wait not found.
Hint: Perhaps this kernel misses some CONFIG_ setting to enable this feature?.
Run 'perf list' for a list of valid events
Usage: perf record [<options>] [<command>]
or: perf record [<options>] -- <command> [<options>]
-e, --event <event> event selector. use 'perf list' to list available events
Solution:
Check whether schedstat tracepoints are exposed. If no, these events are not recorded.
After:
# perf sched record sleep 1
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.163 MB perf.data (1091 samples) ]
# perf sched report
run measurement overhead: 4736 nsecs
sleep measurement overhead: 9059979 nsecs
the run test took 999854 nsecs
the sleep test took 8945271 nsecs
nr_run_events: 716
nr_sleep_events: 785
nr_wakeup_events: 0
...
------------------------------------------------------------
Fixes: 2a09b5de23 ("sched/fair: do not expose some tracepoints to user if CONFIG_SCHEDSTATS is not set")
Signed-off-by: Yang Jihong <yangjihong1@huawei.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Yafang Shao <laoar.shao@gmail.com>
Link: http://lore.kernel.org/lkml/20210713112358.194693-1-yangjihong1@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7234c362cc ]
The AMD platform does not support the functions Ah CPUID leaf. The returned
results for this entry should all remain zero just like the native does:
AMD host:
0x0000000a 0x00: eax=0x00000000 ebx=0x00000000 ecx=0x00000000 edx=0x00000000
(uncanny) AMD guest:
0x0000000a 0x00: eax=0x00000000 ebx=0x00000000 ecx=0x00000000 edx=0x00008000
Fixes: cadbaa039b ("perf/x86/intel: Make anythread filter support conditional")
Signed-off-by: Like Xu <likexu@tencent.com>
Message-Id: <20210628074354.33848-1-likexu@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 251ef6f71b ]
nvme_dev_remove_admin could free dev->admin_q and the admin_tagset
while they are being accessed by nvme_dev_disable(), which can be called
by nvme_reset_work via nvme_remove_dead_ctrl.
Commit cb4bfda62a ("nvme-pci: fix hot removal during error handling")
intended to avoid requests being stuck on a removed controller by killing
the admin queue. But the later fix c8e9e9b764 ("nvme-pci: unquiesce
admin queue on shutdown"), together with nvme_dev_disable(dev, true)
right before nvme_dev_remove_admin() could help dispatch requests and
fail them early, so we don't need nvme_dev_remove_admin() any more.
Fixes: cb4bfda62a ("nvme-pci: fix hot removal during error handling")
Signed-off-by: Casey Chen <cachen@purestorage.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 015fe6fd29 ]
IRQs are requested during driver's ndo_open() and then later
freed up in disable_interrupts() during driver unload.
A race exists where driver can set the CXGB4_FULL_INIT_DONE
flag in ndo_open() after the disable_interrupts() in driver
unload path checks it, and hence misses calling free_irq().
Fix by unregistering netdevice first and sync with driver's
ndo_open(). This ensures disable_interrupts() checks the flag
correctly and frees up the IRQs properly.
Fixes: b37987e8db ("cxgb4: Disable interrupts and napi before unregistering netdev")
Signed-off-by: Shahjada Abul Husain <shahjada@chelsio.com>
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65e2e6c1c2 ]
As the last call to sprd_pwm_apply() might have exited early if
state->enabled was false, the values for period and duty_cycle stored in
pwm->state might not have been written to hardware and it must be
ensured that they are configured before enabling the PWM.
Fixes: 8aae4b02e8 ("pwm: sprd: Add Spreadtrum PWM support")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e02bf5de4 ]
After redirecting, it's already a new path. So the old PMTU info should
be cleared. The IPv6 test "mtu exception plus redirect" should only
has redirect info without old PMTU.
The IPv4 test can not be changed because of legacy.
Fixes: ec81053528 ("selftests: Add redirect tests")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24b671aad4 ]
If the kernel doesn't enable option CONFIG_IPV6_SUBTREES, the RTA_SRC
info will not be exported to userspace in rt6_fill_node(). And ip cmd will
not print "from ::" to the route output. So remove this check.
Fixes: ec81053528 ("selftests: Add redirect tests")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eca81f0914 ]
The "plat->phy_interface" variable is an enum and in this context GCC
will treat it as an unsigned int so the error handling is never
triggered.
Fixes: b9f0b2f634 ("net: stmmac: platform: fix probe for ACPI devices")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ccd27f05ae ]
The goal of commit df789fe752 ("ipv6: Provide ipv6 version of
"disable_policy" sysctl") was to have the disable_policy from ipv4
available on ipv6.
However, it's not exactly the same mechanism. On IPv4, all packets coming
from an interface, which has disable_policy set, bypass the policy check.
For ipv6, this is done only for local packets, ie for packets destinated to
an address configured on the incoming interface.
Let's align ipv6 with ipv4 so that the 'disable_policy' sysctl has the same
effect for both protocols.
My first approach was to create a new kind of route cache entries, to be
able to set DST_NOPOLICY without modifying routes. This would have added a
lot of code. Because the local delivery path is already handled, I choose
to focus on the forwarding path to minimize code churn.
Fixes: df789fe752 ("ipv6: Provide ipv6 version of "disable_policy" sysctl")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 168e696a36 ]
bond_ipsec_offload_ok() is called to check whether the interface supports
ipsec offload or not.
bonding interface support ipsec offload only in active-backup mode.
So, if a bond interface is not in active-backup mode, it should return
false but it returns true.
Fixes: a3b658cfb6 ("bonding: allow xfrm offload setup post-module-load")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a5605505d ]
bonding has been supporting ipsec offload.
When SA is added, bonding just passes SA to its own active real interface.
But it doesn't manage SA.
So, when events(add/del real interface, active real interface change, etc)
occur, bonding can't handle that well because It doesn't manage SA.
So some problems(panic, UAF, refcnt leak)occur.
In order to make it stable, it should manage SA.
That's the reason why struct bond_ipsec is added.
When a new SA is added to bonding interface, it is stored in the
bond_ipsec list. And the SA is passed to a current active real interface.
If events occur, it uses bond_ipsec data to handle these events.
bond->ipsec_list is protected by bond->ipsec_lock.
If a current active real interface is changed, the following logic works.
1. delete all SAs from old active real interface
2. Add all SAs to the new active real interface.
3. If a new active real interface doesn't support ipsec offload or SA's
option, it sets real_dev to NULL.
Fixes: 18cb261afd ("bonding: support hardware encryption offload to slaves")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b121693381 ]
bonding interface can be nested and it supports ipsec offload.
So, it allows setting the nested bonding + ipsec scenario.
But code does not support this scenario.
So, it should be disallowed.
interface graph:
bond2
|
bond1
|
eth0
The nested bonding + ipsec offload may not a real usecase.
So, disallowing this scenario is fine.
Fixes: 18cb261afd ("bonding: support hardware encryption offload to slaves")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a22c39b831 ]
To dereference bond->curr_active_slave, it uses rcu_dereference().
But it and the caller doesn't acquire RCU so a warning occurs.
So add rcu_read_lock().
Test commands:
ip netns add A
ip netns exec A bash
modprobe netdevsim
echo "1 1" > /sys/bus/netdevsim/new_device
ip link add bond0 type bond
ip link set eth0 master bond0
ip link set eth0 up
ip link set bond0 up
ip x s add proto esp dst 14.1.1.1 src 15.1.1.1 spi 0x07 mode \
transport reqid 0x07 replay-window 32 aead 'rfc4106(gcm(aes))' \
0x44434241343332312423222114131211f4f3f2f1 128 sel src 14.0.0.52/24 \
dst 14.0.0.70/24 proto tcp offload dev bond0 dir in
ip x s f
Splat looks like:
=============================
WARNING: suspicious RCU usage
5.13.0-rc3+ #1168 Not tainted
-----------------------------
drivers/net/bonding/bond_main.c:448 suspicious rcu_dereference_check()
usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
2 locks held by ip/705:
#0: ffff888106701780 (&net->xfrm.xfrm_cfg_mutex){+.+.}-{3:3},
at: xfrm_netlink_rcv+0x59/0x80 [xfrm_user]
#1: ffff8880075b0098 (&x->lock){+.-.}-{2:2},
at: xfrm_state_delete+0x16/0x30
stack backtrace:
CPU: 6 PID: 705 Comm: ip Not tainted 5.13.0-rc3+ #1168
Call Trace:
dump_stack+0xa4/0xe5
bond_ipsec_del_sa+0x16a/0x1c0 [bonding]
__xfrm_state_delete+0x51f/0x730
xfrm_state_delete+0x1e/0x30
xfrm_state_flush+0x22f/0x390
xfrm_flush_sa+0xd8/0x260 [xfrm_user]
? xfrm_flush_policy+0x290/0x290 [xfrm_user]
xfrm_user_rcv_msg+0x331/0x660 [xfrm_user]
? rcu_read_lock_sched_held+0x91/0xc0
? xfrm_user_state_lookup.constprop.39+0x320/0x320 [xfrm_user]
? find_held_lock+0x3a/0x1c0
? mutex_lock_io_nested+0x1210/0x1210
? sched_clock_cpu+0x18/0x170
netlink_rcv_skb+0x121/0x350
[ ... ]
Fixes: 18cb261afd ("bonding: support hardware encryption offload to slaves")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b648eba4c6 ]
To dereference bond->curr_active_slave, it uses rcu_dereference().
But it and the caller doesn't acquire RCU so a warning occurs.
So add rcu_read_lock().
Test commands:
ip link add dummy0 type dummy
ip link add bond0 type bond
ip link set dummy0 master bond0
ip link set dummy0 up
ip link set bond0 up
ip x s add proto esp dst 14.1.1.1 src 15.1.1.1 spi 0x07 \
mode transport \
reqid 0x07 replay-window 32 aead 'rfc4106(gcm(aes))' \
0x44434241343332312423222114131211f4f3f2f1 128 sel \
src 14.0.0.52/24 dst 14.0.0.70/24 proto tcp offload \
dev bond0 dir in
Splat looks like:
=============================
WARNING: suspicious RCU usage
5.13.0-rc3+ #1168 Not tainted
-----------------------------
drivers/net/bonding/bond_main.c:411 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
1 lock held by ip/684:
#0: ffffffff9a2757c0 (&net->xfrm.xfrm_cfg_mutex){+.+.}-{3:3},
at: xfrm_netlink_rcv+0x59/0x80 [xfrm_user]
55.191733][ T684] stack backtrace:
CPU: 0 PID: 684 Comm: ip Not tainted 5.13.0-rc3+ #1168
Call Trace:
dump_stack+0xa4/0xe5
bond_ipsec_add_sa+0x18c/0x1f0 [bonding]
xfrm_dev_state_add+0x2a9/0x770
? memcpy+0x38/0x60
xfrm_add_sa+0x2278/0x3b10 [xfrm_user]
? xfrm_get_policy+0xaa0/0xaa0 [xfrm_user]
? register_lock_class+0x1750/0x1750
xfrm_user_rcv_msg+0x331/0x660 [xfrm_user]
? rcu_read_lock_sched_held+0x91/0xc0
? xfrm_user_state_lookup.constprop.39+0x320/0x320 [xfrm_user]
? find_held_lock+0x3a/0x1c0
? mutex_lock_io_nested+0x1210/0x1210
? sched_clock_cpu+0x18/0x170
netlink_rcv_skb+0x121/0x350
? xfrm_user_state_lookup.constprop.39+0x320/0x320 [xfrm_user]
? netlink_ack+0x9d0/0x9d0
? netlink_deliver_tap+0x17c/0xa50
xfrm_netlink_rcv+0x68/0x80 [xfrm_user]
netlink_unicast+0x41c/0x610
? netlink_attachskb+0x710/0x710
netlink_sendmsg+0x6b9/0xb70
[ ... ]
Fixes: 18cb261afd ("bonding: support hardware encryption offload to slaves")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6370cc3bbd ]
Remote KCOV coverage collection enables coverage-guided fuzzing of the
code that is not reachable during normal system call execution. It is
especially helpful for fuzzing networking subsystems, where it is
common to perform packet handling in separate work queues even for the
packets that originated directly from the user space.
Enable coverage-guided frame injection by adding kcov remote handle to
skb extensions. Default initialization in __alloc_skb and
__build_skb_around ensures that no socket buffer that was generated
during a system call will be missed.
Code that is of interest and that performs packet processing should be
annotated with kcov_remote_start()/kcov_remote_stop().
An alternative approach is to determine kcov_handle solely on the
basis of the device/interface that received the specific socket
buffer. However, in this case it would be impossible to distinguish
between packets that originated during normal background network
processes or were intentionally injected from the user space.
Signed-off-by: Aleksandr Nogikh <nogikh@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2342ae10d1 ]
If the 'register_netdev() call fails, we must release the resources
allocated by the previous 'gve_init_priv()' call, as already done in the
remove function.
Add a new label and the missing 'gve_teardown_priv_resources()' in the
error handling path.
Fixes: 893ce44df5 ("gve: Add basic driver framework for Compute Engine Virtual NIC")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af30cbd2f4 ]
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: 5eae00c57f ("i40evf: main driver core")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e85e14d68f ]
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: 19ae1b3fb9 ("fm10k: Add support for PCI power management and error handling")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fea03b1ceb ]
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: 40a914fa72 ("igb: Add support for pci-e Advanced Error Reporting")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd2aefcd5e ]
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: 6fabd715e6 ("ixgbe: Implement PCIe AER support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05682a0a61 ]
Static analysis reports this problem
igc_main.c:4944:20: warning: The left operand of '&'
is a garbage value
if (!(phy_data & SR_1000T_REMOTE_RX_STATUS) &&
~~~~~~~~ ^
phy_data is set by the call to igc_read_phy_reg() only if
there is a read_reg() op, else it is unset and a 0 is
returned. Change the return to -EOPNOTSUPP.
Fixes: 208983f099 ("igc: Add watchdog")
Signed-off-by: Tom Rix <trix@redhat.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b292608db ]
Cleans the next descriptor to watch (next_to_watch) when cleaning the
TX ring.
Failure to do so can cause invalid memory accesses. If igb_poll() runs
while the controller is reset this can lead to the driver try to free
a skb that was already freed.
(The crash is harder to reproduce with the igb driver, but the same
potential problem exists as the code is identical to igc)
Fixes: 7cc6fd4c60 ("igb: Don't bother clearing Tx buffer_info in igb_clean_tx_ring")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reported-by: Erez Geva <erez.geva.ext@siemens.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
There are no error exists once device_create has succeeded, and
therefore no need to call device_destroy from vc_mem_init.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
commit f263a81451 upstream.
Subprograms are calling map_poke_track(), but on program release there is no
hook to call map_poke_untrack(). However, on program release, the aux memory
(and poke descriptor table) is freed even though we still have a reference to
it in the element list of the map aux data. When we run map_poke_run(), we then
end up accessing free'd memory, triggering KASAN in prog_array_map_poke_run():
[...]
[ 402.824689] BUG: KASAN: use-after-free in prog_array_map_poke_run+0xc2/0x34e
[ 402.824698] Read of size 4 at addr ffff8881905a7940 by task hubble-fgs/4337
[ 402.824705] CPU: 1 PID: 4337 Comm: hubble-fgs Tainted: G I 5.12.0+ #399
[ 402.824715] Call Trace:
[ 402.824719] dump_stack+0x93/0xc2
[ 402.824727] print_address_description.constprop.0+0x1a/0x140
[ 402.824736] ? prog_array_map_poke_run+0xc2/0x34e
[ 402.824740] ? prog_array_map_poke_run+0xc2/0x34e
[ 402.824744] kasan_report.cold+0x7c/0xd8
[ 402.824752] ? prog_array_map_poke_run+0xc2/0x34e
[ 402.824757] prog_array_map_poke_run+0xc2/0x34e
[ 402.824765] bpf_fd_array_map_update_elem+0x124/0x1a0
[...]
The elements concerned are walked as follows:
for (i = 0; i < elem->aux->size_poke_tab; i++) {
poke = &elem->aux->poke_tab[i];
[...]
The access to size_poke_tab is a 4 byte read, verified by checking offsets
in the KASAN dump:
[ 402.825004] The buggy address belongs to the object at ffff8881905a7800
which belongs to the cache kmalloc-1k of size 1024
[ 402.825008] The buggy address is located 320 bytes inside of
1024-byte region [ffff8881905a7800, ffff8881905a7c00)
The pahole output of bpf_prog_aux:
struct bpf_prog_aux {
[...]
/* --- cacheline 5 boundary (320 bytes) --- */
u32 size_poke_tab; /* 320 4 */
[...]
In general, subprograms do not necessarily manage their own data structures.
For example, BTF func_info and linfo are just pointers to the main program
structure. This allows reference counting and cleanup to be done on the latter
which simplifies their management a bit. The aux->poke_tab struct, however,
did not follow this logic. The initial proposed fix for this use-after-free
bug further embedded poke data tracking into the subprogram with proper
reference counting. However, Daniel and Alexei questioned why we were treating
these objects special; I agree, its unnecessary. The fix here removes the per
subprogram poke table allocation and map tracking and instead simply points
the aux->poke_tab pointer at the main programs poke table. This way, map
tracking is simplified to the main program and we do not need to manage them
per subprogram.
This also means, bpf_prog_free_deferred(), which unwinds the program reference
counting and kfrees objects, needs to ensure that we don't try to double free
the poke_tab when free'ing the subprog structures. This is easily solved by
NULL'ing the poke_tab pointer. The second detail is to ensure that per
subprogram JIT logic only does fixups on poke_tab[] entries it owns. To do
this, we add a pointer in the poke structure to point at the subprogram value
so JITs can easily check while walking the poke_tab structure if the current
entry belongs to the current program. The aux pointer is stable and therefore
suitable for such comparison. On the jit_subprogs() error path, we omit
cleaning up the poke->aux field because these are only ever referenced from
the JIT side, but on error we will never make it to the JIT, so its fine to
leave them dangling. Removing these pointers would complicate the error path
for no reason. However, we do need to untrack all poke descriptors from the
main program as otherwise they could race with the freeing of JIT memory from
the subprograms. Lastly, a748c6975d ("bpf: propagate poke descriptors to
subprograms") had an off-by-one on the subprogram instruction index range
check as it was testing 'insn_idx >= subprog_start && insn_idx <= subprog_end'.
However, subprog_end is the next subprogram's start instruction.
Fixes: a748c6975d ("bpf: propagate poke descriptors to subprograms")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Co-developed-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210707223848.14580-2-john.fastabend@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d719254c1 upstream.
make[2]: *** No rule to make target 'install'. Stop.
make[1]: *** [Makefile:122: runqslower_install] Error 2
make: *** [Makefile:116: bpf_install] Error 2
There is no rule for target 'install' in tools/bpf/runqslower/Makefile,
and there is no need to install it, so just remove 'runqslower_install'.
Fixes: 9c01546d26 ("tools/bpf: Add runqslower tool to tools/bpf")
Signed-off-by: Wei Li <liwei391@huawei.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210628030409.3459095-1-liwei391@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 358ed62420 upstream.
sk_wmem_schedule makes sure that sk_forward_alloc has enough
bytes for charging that is going to be done by sk_mem_charge.
In the transmit zerocopy path, there is sk_mem_charge but there was
no call to sk_wmem_schedule. This change adds that call.
Without this call to sk_wmem_schedule, sk_forward_alloc can go
negetive which is a bug because sk_forward_alloc is a per-socket
space that has been forward charged so this can't be negative.
Fixes: f214f915e7 ("tcp: enable MSG_ZEROCOPY")
Signed-off-by: Talal Ahmad <talalahmad@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Wei Wang <weiwan@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c7bb4b8903 upstream.
While TCP stack scales reasonably well, there is still one part that
can be used to DDOS it.
IPv6 Packet too big messages have to lookup/insert a new route,
and if abused by attackers, can easily put hosts under high stress,
with many cpus contending on a spinlock while one is stuck in fib6_run_gc()
ip6_protocol_deliver_rcu()
icmpv6_rcv()
icmpv6_notify()
tcp_v6_err()
tcp_v6_mtu_reduced()
inet6_csk_update_pmtu()
ip6_rt_update_pmtu()
__ip6_rt_update_pmtu()
ip6_rt_cache_alloc()
ip6_dst_alloc()
dst_alloc()
ip6_dst_gc()
fib6_run_gc()
spin_lock_bh() ...
Some of our servers have been hit by malicious ICMPv6 packets
trying to _increase_ the MTU/MSS of TCP flows.
We believe these ICMPv6 packets are a result of a bug in one ISP stack,
since they were blindly sent back for _every_ (small) packet sent to them.
These packets are for one TCP flow:
09:24:36.266491 IP6 Addr1 > Victim ICMP6, packet too big, mtu 1460, length 1240
09:24:36.266509 IP6 Addr1 > Victim ICMP6, packet too big, mtu 1460, length 1240
09:24:36.316688 IP6 Addr1 > Victim ICMP6, packet too big, mtu 1460, length 1240
09:24:36.316704 IP6 Addr1 > Victim ICMP6, packet too big, mtu 1460, length 1240
09:24:36.608151 IP6 Addr1 > Victim ICMP6, packet too big, mtu 1460, length 1240
TCP stack can filter some silly requests :
1) MTU below IPV6_MIN_MTU can be filtered early in tcp_v6_err()
2) tcp_v6_mtu_reduced() can drop requests trying to increase current MSS.
This tests happen before the IPv6 routing stack is entered, thus
removing the potential contention and route exhaustion.
Note that IPv6 stack was performing these checks, but too late
(ie : after the route has been added, and after the potential
garbage collect war)
v2: fix typo caught by Martin, thanks !
v3: exports tcp_mtu_to_mss(), caught by David, thanks !
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit be5d1b61a2 upstream.
This commit fixes a bug (found by syzkaller) that could cause spurious
double-initializations for congestion control modules, which could cause
memory leaks or other problems for congestion control modules (like CDG)
that allocate memory in their init functions.
The buggy scenario constructed by syzkaller was something like:
(1) create a TCP socket
(2) initiate a TFO connect via sendto()
(3) while socket is in TCP_SYN_SENT, call setsockopt(TCP_CONGESTION),
which calls:
tcp_set_congestion_control() ->
tcp_reinit_congestion_control() ->
tcp_init_congestion_control()
(4) receive ACK, connection is established, call tcp_init_transfer(),
set icsk_ca_initialized=0 (without first calling cc->release()),
call tcp_init_congestion_control() again.
Note that in this sequence tcp_init_congestion_control() is called
twice without a cc->release() call in between. Thus, for CC modules
that allocate memory in their init() function, e.g, CDG, a memory leak
may occur. The syzkaller tool managed to find a reproducer that
triggered such a leak in CDG.
The bug was introduced when that commit 8919a9b31e ("tcp: Only init
congestion control if not initialized already")
introduced icsk_ca_initialized and set icsk_ca_initialized to 0 in
tcp_init_transfer(), missing the possibility for a sequence like the
one above, where a process could call setsockopt(TCP_CONGESTION) in
state TCP_SYN_SENT (i.e. after the connect() or TFO open sendmsg()),
which would call tcp_init_congestion_control(). It did not intend to
reset any initialization that the user had already explicitly made;
it just missed the possibility of that particular sequence (which
syzkaller managed to find).
Fixes: 8919a9b31e ("tcp: Only init congestion control if not initialized already")
Reported-by: syzbot+f1e24a0594d4e3a895d3@syzkaller.appspotmail.com
Signed-off-by: Nguyen Dinh Phi <phind.uet@gmail.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Tested-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 561022acb1 upstream.
While tp->mtu_info is read while socket is owned, the write
sides happen from err handlers (tcp_v[46]_mtu_reduced)
which only own the socket spinlock.
Fixes: 563d34d057 ("tcp: dont drop MTU reduction indications")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 71158bb1f2 upstream.
The MPTCP receive path is hooked only into the TCP slow-path.
The DSS presence allows plain MPTCP traffic to hit that
consistently.
Since commit e1ff9e82e2 ("net: mptcp: improve fallback to TCP"),
when an MPTCP socket falls back to TCP, it can hit the TCP receive
fast-path, and delay or stop triggering the event notification.
Address the issue explicitly disabling the header prediction
for MPTCP sockets.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/200
Fixes: e1ff9e82e2 ("net: mptcp: improve fallback to TCP")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2d6608b57c upstream.
The degree values were reversed out from the magic tap values of 7 (in)
and 15 + inversion (out) initially suggested by Aspeed.
With the patch tacoma survives several gigabytes of reads and writes
using dd while without it locks up randomly during the boot process.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20210625061017.1149942-1-andrew@aj.id.au
Fixes: 2fc88f9235 ("mmc: sdhci-of-aspeed: Expose clock phase controls")
Fixes: 961216c135 ("ARM: dts: aspeed: Add Rainier system")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca46ad2214 upstream.
Tacoma and Rainier both have a line-names array that is too long:
gpio gpiochip0: gpio-line-names is length 232 but should be at most length 208
This was probably copied from an AST2500 device tree that did have more
GPIOs on the controller.
Fixes: e9b24b55ca ("ARM: dts: aspeed: rainier: Add gpio line names")
Fixes: 2f68e4e7df ("ARM: dts: aspeed: tacoma: Add gpio line names")
Link: https://lore.kernel.org/r/20210624090742.56640-1-joel@jms.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d952cfaf0c upstream.
When a new CONFIG option is available, Kbuild shows a prompt to get
the user input.
$ make
[ snip ]
Core Scheduling for SMT (SCHED_CORE) [N/y/?] (NEW)
This is the only interactive place in the build process.
Commit 174a1dcc96 ("kbuild: sink stdout from cmd for silent build")
suppressed Kconfig prompts as well because syncconfig is invoked by
the 'cmd' macro. You cannot notice the fact that Kconfig is waiting
for the user input.
Use 'kecho' to show the equivalent short log without suppressing stdout
from sub-make.
Fixes: 174a1dcc96 ("kbuild: sink stdout from cmd for silent build")
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Tested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit deb7178eb9 upstream.
fp is netdev private data and it cannot be
used after free_netdev() call. Using fp after free_netdev()
can cause UAF bug. Fix it by moving free_netdev() after error message.
Fixes: 61414f5ec9 ("FDDI: defza: Add support for DEC FDDIcontroller 700
TURBOchannel adapter")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bcb9928a15 upstream.
This was not caught because there is no switch driver which implements
the .port_bridge_join but not .port_bridge_leave method, but it should
nonetheless be fixed, as in certain conditions (driver development) it
might lead to NULL pointer dereference.
Fixes: f66a6a69f9 ("net: dsa: permit cross-chip bridging between all trees in the system")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67a9c94317 upstream.
skb_tunnel_info() returns pointer of lwtstate->data as ip_tunnel_info
type without validation. lwtstate->data can have various types such as
mpls_iptunnel_encap, etc and these are not compatible.
So skb_tunnel_info() should validate before returning that pointer.
Splat looks like:
BUG: KASAN: slab-out-of-bounds in vxlan_get_route+0x418/0x4b0 [vxlan]
Read of size 2 at addr ffff888106ec2698 by task ping/811
CPU: 1 PID: 811 Comm: ping Not tainted 5.13.0+ #1195
Call Trace:
dump_stack_lvl+0x56/0x7b
print_address_description.constprop.8.cold.13+0x13/0x2ee
? vxlan_get_route+0x418/0x4b0 [vxlan]
? vxlan_get_route+0x418/0x4b0 [vxlan]
kasan_report.cold.14+0x83/0xdf
? vxlan_get_route+0x418/0x4b0 [vxlan]
vxlan_get_route+0x418/0x4b0 [vxlan]
[ ... ]
vxlan_xmit_one+0x148b/0x32b0 [vxlan]
[ ... ]
vxlan_xmit+0x25c5/0x4780 [vxlan]
[ ... ]
dev_hard_start_xmit+0x1ae/0x6e0
__dev_queue_xmit+0x1f39/0x31a0
[ ... ]
neigh_xmit+0x2f9/0x940
mpls_xmit+0x911/0x1600 [mpls_iptunnel]
lwtunnel_xmit+0x18f/0x450
ip_finish_output2+0x867/0x2040
[ ... ]
Fixes: 61adedf3e3 ("route: move lwtunnel state to dst_entry")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0336f8ffec upstream.
priv is netdev private data and it cannot be
used after free_netdev() call. Using priv after free_netdev()
can cause UAF bug. Fix it by moving free_netdev() at the end of the
function.
Fixes: 1e0a8b13d3 ("tlan: cancel work at remove path")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad297cd2db upstream.
adpt is netdev private data and it cannot be
used after free_netdev() call. Using adpt after free_netdev()
can cause UAF bug. Fix it by moving free_netdev() at the end of the
function.
Fixes: 54e19bc74f ("net: qcom/emac: do not use devm on internal phy pdev")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c78eaeebe8 upstream.
In case of netdev registration failure the code path will
jump to init_fail label:
init_fail:
netdev_err(ndev, "init failed\n");
moxart_mac_free_memory(ndev);
irq_map_fail:
free_netdev(ndev);
return ret;
So, there is no need to call free_netdev() before jumping
to error handling path, since it can cause UAF or double-free
bug.
Fixes: 6c821bd9ed ("net: Add MOXA ART SoCs ethernet driver")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9992a078b1 upstream.
Commit 28e104d002 ("net: ip_tunnel: fix mtu calculation") removed
dev->hard_header_len subtraction when calculate MTU for tunnel devices
as there is an overhead for device that has header_ops.
But there are ETHER tunnel devices, like gre_tap or erspan, which don't
have header_ops but set dev->hard_header_len during setup. This makes
pkts greater than (MTU - ETH_HLEN) could not be xmited. Fix it by
subtracting the ETHER tunnel devices' dev->hard_header_len for MTU
calculation.
Fixes: 28e104d002 ("net: ip_tunnel: fix mtu calculation")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b452550a2 upstream.
Make sure that we disable each of the TX and RX queues in the TDMA and
RDMA control registers. This is a correctness change to be symmetrical
with the code that enables the TX and RX queues.
Tested-by: Maxime Ripard <maxime@cerno.tech>
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09adf7566d upstream.
There are two pointers in struct xfrm_state_offload, *dev, *real_dev.
These are used in callback functions of struct xfrmdev_ops.
The *dev points whether bonding interface or real interface.
If bonding ipsec offload is used, it points bonding interface If not,
it points real interface.
And real_dev always points real interface.
So, netdevsim should always use real_dev instead of dev.
Of course, real_dev always not be null.
Test commands:
ip netns add A
ip netns exec A bash
modprobe netdevsim
echo "1 1" > /sys/bus/netdevsim/new_device
ip link add bond0 type bond mode active-backup
ip link set eth0 master bond0
ip link set eth0 up
ip link set bond0 up
ip x s add proto esp dst 14.1.1.1 src 15.1.1.1 spi 0x07 mode \
transport reqid 0x07 replay-window 32 aead 'rfc4106(gcm(aes))' \
0x44434241343332312423222114131211f4f3f2f1 128 sel src 14.0.0.52/24 \
dst 14.0.0.70/24 proto tcp offload dev bond0 dir in
Splat looks like:
BUG: spinlock bad magic on CPU#5, kworker/5:1/53
lock: 0xffff8881068c2cc8, .magic: 11121314, .owner: <none>/-1,
.owner_cpu: -235736076
CPU: 5 PID: 53 Comm: kworker/5:1 Not tainted 5.13.0-rc3+ #1168
Workqueue: events linkwatch_event
Call Trace:
dump_stack+0xa4/0xe5
do_raw_spin_lock+0x20b/0x270
? rwlock_bug.part.1+0x90/0x90
_raw_spin_lock_nested+0x5f/0x70
bond_get_stats+0xe4/0x4c0 [bonding]
? rcu_read_lock_sched_held+0xc0/0xc0
? bond_neigh_init+0x2c0/0x2c0 [bonding]
? dev_get_alias+0xe2/0x190
? dev_get_port_parent_id+0x14a/0x360
? rtnl_unregister+0x190/0x190
? dev_get_phys_port_name+0xa0/0xa0
? memset+0x1f/0x40
? memcpy+0x38/0x60
? rtnl_phys_switch_id_fill+0x91/0x100
dev_get_stats+0x8c/0x270
rtnl_fill_stats+0x44/0xbe0
? nla_put+0xbe/0x140
rtnl_fill_ifinfo+0x1054/0x3ad0
[ ... ]
Fixes: 272c2330ad ("xfrm: bail early on slave pass over skb")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a019abd802 upstream.
Since commit 2796d0c648 ("bridge: Automatically manage
port promiscuous mode.")
bridges with `vlan_filtering 1` and only 1 auto-port don't
set IFF_PROMISC for unicast-filtering-capable ports.
Normally on port changes `br_manage_promisc` is called to
update the promisc flags and unicast filters if necessary,
but it cannot distinguish between *new* ports and ones
losing their promisc flag, and new ports end up not
receiving the MAC address list.
Fix this by calling `br_fdb_sync_static` in `br_add_if`
after the port promisc flags are updated and the unicast
filter was supposed to have been filled.
Fixes: 2796d0c648 ("bridge: Automatically manage port promiscuous mode.")
Signed-off-by: Wolfgang Bumiller <w.bumiller@proxmox.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77ac5e40c4 upstream.
When cleaning up the nf_table in tcf_ct_flow_table_cleanup_work
there is no guarantee that the callback list, added to by
nf_flow_table_offload_add_cb, is empty. This means that it is
possible that the flow_block_cb memory allocated will be lost.
Fix this by iterating the list and freeing the flow_block_cb entries
before freeing the nf_table entry (via freeing ct_ft).
Fixes: 978703f425 ("netfilter: flowtable: Add API for registering to flow table events")
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b22580233d upstream.
Commit dacce2be33 ("vmxnet3: add geneve and vxlan tunnel offload
support") added support for encapsulation offload. However, the inner
offload capability is to be restricted to UDP tunnels with default
Vxlan and Geneve ports.
This patch fixes the issue for tunnels with non-default ports using
features check capability and filtering appropriate features for such
tunnels.
Fixes: dacce2be33 ("vmxnet3: add geneve and vxlan tunnel offload support")
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8955b90c3c upstream.
The confirm operation should be checked. If there are any failed,
the packet should be dropped like in ovs and netfilter.
Fixes: b57dc7c13e ("net/sched: Introduce action ct")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40fc3054b4 upstream.
Commit 628a5c5618 ("[INET]: Add IP(V6)_PMTUDISC_RPOBE") introduced
ip6_skb_dst_mtu with return value of signed int which is inconsistent
with actually returned values. Also 2 users of this function actually
assign its value to unsigned int variable and only __xfrm6_output
assigns result of this function to signed variable but actually uses
as unsigned in further comparisons and calls. Change this function
to return unsigned int value.
Fixes: 628a5c5618 ("[INET]: Add IP(V6)_PMTUDISC_RPOBE")
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c07fff3492 upstream.
Commit 23e8b470c7 ("net: dsa: mv88e6xxx: Add devlink param for ATU
hash algorithm.") introduced ATU hash algorithm access via devlink, but
did not enable it for Topaz.
Enable this feature also for Topaz.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: 23e8b470c7 ("net: dsa: mv88e6xxx: Add devlink param for ATU hash algorithm.")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3709488790 upstream.
Commit 9e5baf9b36 ("net: dsa: mv88e6xxx: add RMU disable op")
introduced .rmu_disable() method with implementation for several models,
but forgot to add Topaz, which can use the Peridot implementation.
Use the Peridot implementation of .rmu_disable() on Topaz.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: 9e5baf9b36 ("net: dsa: mv88e6xxx: add RMU disable op")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7da467d82d upstream.
Commit f3a2cd326e ("net: dsa: mv88e6xxx: introduce .port_set_policy")
introduced .port_set_policy() method with implementation for several
models, but forgot to add Topaz, which can use the 6352 implementation.
Use the 6352 implementation of .port_set_policy() on Topaz.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: f3a2cd326e ("net: dsa: mv88e6xxx: introduce .port_set_policy")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a3c680aa2 upstream.
Setting the EXT_ENERGY_DET_MASK bit allows the port energy detection
logic of the internal PHY to prevent the system from sleeping. Some
internal PHYs will report that energy is detected when the network
interface is closed which can prevent the system from going to sleep
if WoL is enabled when the interface is brought down.
Since the driver does not support waking the system on this logic,
this commit clears the bit whenever the internal PHY is powered up
and the other logic for manipulating the bit is removed since it
serves no useful function.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 122e093c17 upstream.
On systems with memory nodes sorted in descending order, for instance Dell
Precision WorkStation T5500, the struct pages for higher PFNs and
respectively lower nodes, could be overwritten by the initialization of
struct pages corresponding to the holes in the memory sections.
For example for the below memory layout
[ 0.245624] Early memory node ranges
[ 0.248496] node 1: [mem 0x0000000000001000-0x0000000000090fff]
[ 0.251376] node 1: [mem 0x0000000000100000-0x00000000dbdf8fff]
[ 0.254256] node 1: [mem 0x0000000100000000-0x0000001423ffffff]
[ 0.257144] node 0: [mem 0x0000001424000000-0x0000002023ffffff]
the range 0x1424000000 - 0x1428000000 in the beginning of node 0 starts in
the middle of a section and will be considered as a hole during the
initialization of the last section in node 1.
The wrong initialization of the memory map causes panic on boot when
CONFIG_DEBUG_VM is enabled.
Reorder loop order of the memory map initialization so that the outer loop
will always iterate over populated memory regions in the ascending order
and the inner loop will select the zone corresponding to the PFN range.
This way initialization of the struct pages for the memory holes will be
always done for the ranges that are actually not populated.
[akpm@linux-foundation.org: coding style fixes]
Link: https://lkml.kernel.org/r/YNXlMqBbL+tBG7yq@kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=213073
Link: https://lkml.kernel.org/r/20210624062305.10940-1-rppt@kernel.org
Fixes: 0740a50b9b ("mm/page_alloc.c: refactor initialization of struct page for holes in memory layout")
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Boris Petkov <bp@alien8.de>
Cc: Robert Shteynfeld <robert.shteynfeld@gmail.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: David Hildenbrand <david@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[rppt: tweak for compatibility with IA64's override of memmap_init]
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f34f1eac3 upstream.
We tried to do something similar in b569a17607 ("userfaultfd: wp: drop
_PAGE_UFFD_WP properly when fork") previously, but it's not doing it all
right.. A few fixes around the code path:
1. We were referencing VM_UFFD_WP vm_flags on the _old_ vma rather
than the new vma. That's overlooked in b569a17607, so it won't work
as expected. Thanks to the recent rework on fork code
(7a4830c380), we can easily get the new vma now, so switch the
checks to that.
2. Dropping the uffd-wp bit in copy_huge_pmd() could be wrong if the
huge pmd is a migration huge pmd. When it happens, instead of using
pmd_uffd_wp(), we should use pmd_swp_uffd_wp(). The fix is simply to
handle them separately.
3. Forget to carry over uffd-wp bit for a write migration huge pmd
entry. This also happens in copy_huge_pmd(), where we converted a
write huge migration entry into a read one.
4. In copy_nonpresent_pte(), drop uffd-wp if necessary for swap ptes.
5. In copy_present_page() when COW is enforced when fork(), we also
need to pass over the uffd-wp bit if VM_UFFD_WP is armed on the new
vma, and when the pte to be copied has uffd-wp bit set.
Remove the comment in copy_present_pte() about this. It won't help a huge
lot to only comment there, but comment everywhere would be an overkill.
Let's assume the commit messages would help.
[peterx@redhat.com: fix a few thp pmd missing uffd-wp bit]
Link: https://lkml.kernel.org/r/20210428225030.9708-4-peterx@redhat.com
Link: https://lkml.kernel.org/r/20210428225030.9708-3-peterx@redhat.com
Fixes: b569a17607 ("userfaultfd: wp: drop _PAGE_UFFD_WP properly when fork")
Signed-off-by: Peter Xu <peterx@redhat.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Axel Rasmussen <axelrasmussen@google.com>
Cc: Brian Geffon <bgeffon@google.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Joe Perches <joe@perches.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Wang Qing <wangqing@vivo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5fc7a5f6fd upstream.
Patch series "mm/uffd: Misc fix for uffd-wp and one more test".
This series tries to fix some corner case bugs for uffd-wp on either thp
or fork(). Then it introduced a new test with pagemap/pageout.
Patch layout:
Patch 1: cleanup for THP, it'll slightly simplify the follow up patches
Patch 2-4: misc fixes for uffd-wp here and there; please refer to each patch
Patch 5: add pagemap support for uffd-wp
Patch 6: add pagemap/pageout test for uffd-wp
The last test introduced can also verify some of the fixes in previous
patches, as the test will fail without the fixes. However it's not easy
to verify all the changes in patch 2-4, but hopefully they can still be
properly reviewed.
Note that if considering the ongoing uffd-wp shmem & hugetlbfs work, patch
5 will be incomplete as it's missing e.g. hugetlbfs part or the special
swap pte detection. However that's not needed in this series, and since
that series is still during review, this series does not depend on that
one (the last test only runs with anonymous memory, not file-backed). So
this series can be merged even before that series.
This patch (of 6):
Huge zero page is handled in a special path in copy_huge_pmd(), however it
should share most codes with a normal thp page. Trying to share more code
with it by removing the special path. The only leftover so far is the
huge zero page refcounting (mm_get_huge_zero_page()), because that's
separately done with a global counter.
This prepares for a future patch to modify the huge pmd to be installed,
so that we don't need to duplicate it explicitly into huge zero page case
too.
Link: https://lkml.kernel.org/r/20210428225030.9708-1-peterx@redhat.com
Link: https://lkml.kernel.org/r/20210428225030.9708-2-peterx@redhat.com
Signed-off-by: Peter Xu <peterx@redhat.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Mike Kravetz <mike.kravetz@oracle.com>, peterx@redhat.com
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Axel Rasmussen <axelrasmussen@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Brian Geffon <bgeffon@google.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Joe Perches <joe@perches.com>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Wang Qing <wangqing@vivo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3a52a48973 ]
Move the turris-mox-rwtm firmware node from Turris MOX' device tree into
the generic armada-37xx.dtsi file and use the generic compatible string
'marvell,armada-3700-rwtm-firmware' instead of the current one.
Turris MOX DTS file contains also old compatible string for backward
compatibility.
The Turris MOX rWTM firmware can be used on any Armada 37xx device,
giving them access to the rWTM hardware random number generator, which
is otherwise unavailable.
This change allows Linux to load the turris-mox-rwtm.ko module on these
boards.
Tested on ESPRESSObin v5 with both default Marvell WTMI firmware and
CZ.NIC's firmware. With default WTMI firmware the turris-mox-rwtm fails
to probe, while with CZ.NIC's firmware it registers the HW random number
generator.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90ae47215d ]
Add more generic compatible string 'marvell,armada-3700-rwtm-firmware' for
this driver, since it can also be used on other Armada 3720 devices.
Current compatible string 'cznic,turris-mox-rwtm' is kept for backward
compatibility.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03313d1c3a ]
The optional @ref parameter might contain an NULL node_name, so
prevent dereferencing it in cifs_compose_mount_options().
Addresses-Coverity: 1476408 ("Explicit null dereferenced")
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41d71fe59c ]
The existing CALL_ON_STACK() macro allows for subtle bugs:
- There is no type checking of the function that is being called. That
is: missing or too many arguments do not cause any compile error or
warning. The same is true if the return type of the called function
changes. This can lead to quite random bugs.
- Sign and zero extension of arguments is missing. Given that the s390
C ABI requires that the caller of a function performs proper sign
and zero extension this can also lead to subtle bugs.
- If arguments to the CALL_ON_STACK() macros contain functions calls
register corruption can happen due to register asm constructs being
used.
Therefore introduce a new call_on_stack() macro which is supposed to
fix all these problems.
Reviewed-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8e9cc20b8 ]
tinyconfig fails to boot, because without CONFIG_BUG report_bug()
always returns BUG_TRAP_TYPE_BUG, which causes mc 0,0 in
test_monitor_call() to panic. Fix by skipping the test without
CONFIG_BUG.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e5c9f9a75 ]
Zone device is enabled after thermal_zone_of_sensor_register() completion,
but it's not disabled before senor is unregistered, leaving temperature
polling active. This results in accessing a disabled zone device and
produces a warning about this problem. Stop zone device before
unregistering it in order to fix this "use-after-free" problem.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210616190417.32214-3-digetx@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72d0ad7cb5 ]
The time remaining until expiry of the refresh_timer can be negative.
Casting the type to an unsigned 64-bit value will cause integer
underflow, making the runtime_refresh_within return false instead of
true. These situations are rare, but they do happen.
This does not cause user-facing issues or errors; other than
possibly unthrottling cfs_rq's using runtime from the previous period(s),
making the CFS bandwidth enforcement less strict in those (special)
situations.
Signed-off-by: Odin Ugedal <odin@uged.al>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Ben Segall <bsegall@google.com>
Link: https://lore.kernel.org/r/20210629121452.18429-1-odin@uged.al
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49da96d779 ]
Offlining a SATA device connected to a hisi SAS controller and then
scanning the host will result in detecting 255 non-existent devices:
# lsscsi
[2:0:0:0] disk ATA Samsung SSD 860 2B6Q /dev/sda
[2:0:1:0] disk ATA WDC WD2003FYYS-3 1D01 /dev/sdb
[2:0:2:0] disk SEAGATE ST600MM0006 B001 /dev/sdc
# echo "offline" > /sys/block/sdb/device/state
# echo "- - -" > /sys/class/scsi_host/host2/scan
# lsscsi
[2:0:0:0] disk ATA Samsung SSD 860 2B6Q /dev/sda
[2:0:1:0] disk ATA WDC WD2003FYYS-3 1D01 /dev/sdb
[2:0:1:1] disk ATA WDC WD2003FYYS-3 1D01 /dev/sdh
...
[2:0:1:255] disk ATA WDC WD2003FYYS-3 1D01 /dev/sdjb
After a REPORT LUN command issued to the offline device fails, the SCSI
midlayer tries to do a sequential scan of all devices whose LUN number is
not 0. However, SATA does not support LUN numbers at all.
Introduce a generic sas_slave_alloc() handler which will return -ENXIO for
SATA devices if the requested LUN number is larger than 0 and make libsas
drivers use this function as their .slave_alloc callback.
Link: https://lore.kernel.org/r/20210622034037.1467088-1-yuyufen@huawei.com
Reported-by: Wu Bo <wubo40@huawei.com>
Suggested-by: John Garry <john.garry@huawei.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 332a9dd1d8 ]
The shifting of the u8 integer returned fom ahc_inb(ahc, port+3) by 24 bits
to the left will be promoted to a 32 bit signed int and then sign-extended
to a u64. In the event that the top bit of the u8 is set then all then all
the upper 32 bits of the u64 end up as also being set because of the
sign-extension. Fix this by casting the u8 values to a u64 before the 24
bit left shift.
[ This dates back to 2002, I found the offending commit from the git
history git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git,
commit f58eb66c0b0a ("Update aic7xxx driver to 6.2.10...") ]
Link: https://lore.kernel.org/r/20210621151727.20667-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Addresses-Coverity: ("Unintended sign extension")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 742b0d7e15 ]
Interrupt line can be configured on different hardware in different way,
even inverted. Therefore driver should not enforce specific trigger
type - edge falling - but instead rely on Devicetree to configure it.
The Maxim 77686 datasheet describes the interrupt line as active low
with a requirement of acknowledge from the CPU therefore the edge
falling is not correct.
The interrupt line is shared between PMIC and RTC driver, so using level
sensitive interrupt is here especially important to avoid races. With
an edge configuration in case if first PMIC signals interrupt followed
shortly after by the RTC, the interrupt might not be yet cleared/acked
thus the second one would not be noticed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210526172036.183223-6-krzysztof.kozlowski@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a979522a1a ]
To avoid unnecessary recompilations, mkcompile_h does not regenerate
compile.h if just the timestamp changed.
Though, if KBUILD_BUILD_TIMESTAMP is set, an explicit timestamp for the
build was requested, in which case we should not ignore it.
If a user follows the documentation for reproducible builds [1] and
defines KBUILD_BUILD_TIMESTAMP as the git commit timestamp, a clean
build will have the correct timestamp. A subsequent cherry-pick (or
amend) changes the commit timestamp and if an incremental build is done
with a different KBUILD_BUILD_TIMESTAMP now, that new value is not taken
into consideration. But it should for reproducibility.
Hence, whenever KBUILD_BUILD_TIMESTAMP is explicitly set, do not ignore
UTS_VERSION when making a decision about whether the regenerated version
of compile.h should be moved into place.
[1] https://www.kernel.org/doc/html/latest/kbuild/reproducible-builds.html
Signed-off-by: Matthias Maennich <maennich@google.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ae5950db6 ]
With -Wshadow:
drivers/thermal/rcar_gen3_thermal.c: In function ‘rcar_gen3_thermal_probe’:
drivers/thermal/rcar_gen3_thermal.c:310:13: warning: declaration of ‘rcar_gen3_ths_tj_1’ shadows a global declaration [-Wshadow]
310 | const int *rcar_gen3_ths_tj_1 = of_device_get_match_data(dev);
| ^~~~~~~~~~~~~~~~~~
drivers/thermal/rcar_gen3_thermal.c:246:18: note: shadowed declaration is here
246 | static const int rcar_gen3_ths_tj_1 = 126;
| ^~~~~~~~~~~~~~~~~~
To add to the confusion, the local variable has a different type.
Fix the shadowing by renaming the local variable to ths_tj_1.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/9ea7e65d0331daba96f9a7925cb3d12d2170efb1.1623076804.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15a5261e4d ]
This fixes multiple issues with the current non-existent PCIe clock setup:
The controller can run at up to 250MHz, so use a parent that provides this
clock.
The PHY needs an exact 100MHz reference clock to function if the PCIe
refclock is not fed in via the refclock pads. While this mode is not
supported (yet) in the driver it doesn't hurt to make sure we are
providing a clock with the right rate.
The AUX clock is specified to have a maximum clock rate of 10MHz. So
the current setup, which drives it straight from the 25MHz oscillator is
actually overclocking the AUX input.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8240c972c1 ]
On LS2088A-RDB board, if the spi-fsl-dspi driver is built as module
then its probe fails with the following warning:
[ 10.471363] couldn't get idr
[ 10.471381] WARNING: CPU: 4 PID: 488 at drivers/spi/spi.c:2689 spi_register_controller+0x73c/0x8d0
...
[ 10.471651] fsl-dspi 2100000.spi: Problem registering DSPI ctlr
[ 10.471708] fsl-dspi: probe of 2100000.spi failed with error -16
Reason for the failure is that bus-num property is set for dspi node.
However, bus-num property is not set for the qspi node. If probe for
spi-fsl-qspi happens first then id 0 is dynamically allocated to it.
Call to spi_register_controller() from spi-fsl-dspi driver then fails.
Since commit 29d2daf2c3 ("spi: spi-fsl-dspi: Make bus-num property
optional") bus-num property is optional. Remove bus-num property from
dspi node to fix the issue.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd778b8939 ]
The tegra186_bpmp_ops symbol is used on Tegra234, so make sure it's
available.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e2d0ee225e ]
The tegra30_fuse_read() symbol is used on Tegra234, so make sure it's
available.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 093a474ce1 ]
If the PM related modules are not loaded and PM firmware not configured,
the system suspend fails to resume. Let's fix this by adding initial
platform_suspend_ops to block suspend and warn about missing modules.
When pm33xx and wkup_m3_ipc have been loaded and m3 coprocessor booted
with it's firmware, pm33xx sets up working platform_suspend_ops. Note
that we need to configure at least PM_SUSPEND_STANDBY to have
suspend_set_ops().
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4bf4abe190 ]
On some STM32 MP15 boards, stpmic node is not correct which generates
warnings running "make dtbs_check W=1" command. Issues are:
-"regulator-active-discharge" is not a boolean but an uint32.
-"regulator-over-current-protection" is not a valid entry for vref_ddr.
-LDO4 has a fixed voltage (3v3) so min/max entries are not allowed.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f493162319 ]
The Seeed SoM-STM32MP157C device tree had the eMMC’s (SDMMC2) VQMMC
supply set to v3v3 (buck4), the same as the VMMC supply. That was
incorrect, as on the SoM, the VQMMC supply is provided from vdd (buck3)
instead.
Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0740fb869 ]
Fix compilation warning on 64bit platforms caused by implicit promotion
of 32bit signed integer to a 64bit unsigned value which happens after
enabling compile-testing of the EMC drivers.
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf24b91f4b ]
Fix following warning observed with "make dtbs_check W=1" command.
It concerns f429 eval and disco boards, f769 disco board.
Warning (unit_address_vs_reg): /gpio_keys/button@0: node has a unit name,
but no reg or ranges property
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0171b07373 ]
The microSD card detect pin is physically connected to the MPU pin PI3.
The Device Tree configuration of the card detect pin was wrong—it was
set to pin PB7 instead. If such configuration was used, the kernel would
hang on “Waiting for root device” when booting from a microSD card.
Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4dd6066bc ]
The 3v3 regulator GPIO is GP6 and not GP7, which is the DDR regulator.
Both regulators are always-on, nevertheless the DT model needs to be
corrected, fix it.
Reported-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f45da704d ]
All Tegra boards which use WM8903 audio codec are specifying a wrong
polarity for the headphones detection GPIO. The kernel driver hardcodes
the polarity to active-low, which is the correct polarity, so we can fix
the device-trees safely.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69db725cdb ]
The MCU RGMII MCU_RGMII1_TXC pin is defined as input by mistake, although
this does not make any difference functionality wise it's better to update
to avoid confusion.
Hence fix MCU RGMII MCU_RGMII1_TXC pin pinmux definitions to be an output
in K3 am654x/j721e/j7200 board files.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210526132041.6104-1-grygorii.strashko@ti.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e7f5ee113 ]
A number of sub-mailbox node names in various OMAP2+ dts files are
currently using underscores. This is not adhering to the node name
convention, fix all of these to use hiphens.
These nodes are already using the prefix mbox, so they will be in
compliance with the sub-mailbox node name convention being added in
the OMAP Mailbox YAML binding as well.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7d30b8fcd ]
The ti,no-reset-on-init flag need to be at the interconnect target module
level for the modules that have it defined.
The ti-sysc driver handles this case, but produces warning, not a critical
issue.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2566d5b8c1 ]
The ti,no-reset-on-init flag need to be at the interconnect target module
level for the modules that have it defined.
The ti-sysc driver handles this case, but produces warning, not a critical
issue.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b644c5e01c ]
The ti,no-reset-on-init flag need to be at the interconnect target module
level for the modules that have it defined.
The ti-sysc driver handles this case, but produces warning, not a critical
issue.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 174a1dcc96 ]
When building with 'make -s', no output to stdout should be printed.
As Arnd Bergmann reported [1], mkimage shows the detailed information
of the generated images.
I think this should be suppressed by the 'cmd' macro instead of by
individual scripts.
Insert 'exec >/dev/null;' in order to redirect stdout to /dev/null for
silent builds.
[Note about this implementation]
'exec >/dev/null;' may look somewhat tricky, but this has a reason.
Appending '>/dev/null' at the end of command line is a common way for
redirection, so I first tried this:
cmd = @set -e; $(echo-cmd) $(cmd_$(1)) >/dev/null
... but it would not work if $(cmd_$(1)) itself contains a redirection.
For example, cmd_wrap in scripts/Makefile.asm-generic redirects the
output from the 'echo' command into the target file.
It would be expanded into:
echo "#include <asm-generic/$*.h>" > $@ >/dev/null
Then, the target file gets empty because the string will go to /dev/null
instead of $@.
Next, I tried this:
cmd = @set -e; $(echo-cmd) { $(cmd_$(1)); } >/dev/null
The form above would be expanded into:
{ echo "#include <asm-generic/$*.h>" > $@; } >/dev/null
This works as expected. However, it would be a syntax error if
$(cmd_$(1)) is empty.
When CONFIG_TRIM_UNUSED_KSYMS is disabled, $(call cmd,gen_ksymdeps) in
scripts/Makefile.build would be expanded into:
set -e; { ; } >/dev/null
..., which causes an syntax error.
I also tried this:
cmd = @set -e; $(echo-cmd) ( $(cmd_$(1)) ) >/dev/null
... but this causes a syntax error for the same reason.
So, finally I adopted:
cmd = @set -e; $(echo-cmd) exec >/dev/null; $(cmd_$(1))
[1]: https://lore.kernel.org/lkml/20210514135752.2910387-1-arnd@kernel.org/
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 723de6a412 ]
Without SoC specific PHY fixups the network interface on this board will
fail to work. Provide missing DT properties to make it work again.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4beba40119 ]
This adds a mounting matrix to the accelerometer
on the TVK1281618 R3.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4917b70281 ]
Rename the AB8500 gpio controller node from ab8500-gpio to
ab8500-gpiocontroller, since -gpio is a common suffix for
gpio consumers.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b82f8e2992 ]
A test with the command below gives this error:
/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dt.yaml:
sdmmcio-regulator: states:0:
[1800000, 1, 3300000, 0] is too long
dtbs_check expects regulator-gpio states in a format
of 2 per item, so fix them all.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/
regulator/gpio-regulator.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210510215840.16270-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14cdc1f243 ]
Serial interface uart3 on phyFLEX board is capable of 5-wire connection
including signals RTS and CTS for hardware flow control.
Fix signals UART3_CTS_B and UART3_RTS_B padmux assignments and add
missing property "uart-has-rtscts" to allow serial interface to be
configured and used with the hardware flow control.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05cf8fffcd ]
The to_ti_syscon_reset_data macro currently only works if the
parameter passed into it is called 'rcdev'.
Fixes a checkpatch --strict issue:
CHECK: Macro argument reuse 'rcdev' - possible side-effects?
#53: FILE: drivers/reset/reset-ti-syscon.c:53:
+#define to_ti_syscon_reset_data(rcdev) \
+ container_of(rcdev, struct ti_syscon_reset_data, rcdev)
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7ecfad495 ]
A test with the command below aimed at powerpc generates
notifications in the Rockchip arm64 tree.
Fix pinctrl "sleep" nodename by renaming it to "suspend"
for rk3399.dtsi
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/powerpc/sleep.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210126110221.10815-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dfbfb86a43 ]
A test with the command below aimed at powerpc generates
notifications in the Rockchip ARM tree.
Fix pinctrl "sleep" nodename by renaming it to "suspend"
for rk3036-kylin and rk3288
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/powerpc/sleep.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210126110221.10815-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
reset-gpios = <&gpio 17 1>; // Pin11 on GPIO header
reset-gpios = <&gpio 17 0>; // Pin11 on GPIO header
};
};
};
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
