Certain transfer ring access patterns can cause the controller to hang
fetching TRBs for a USB2.0 endpoint.
- If two USB2.0 endpoints are active at once and
- Both endpoints are traversing a Link TRB where the following segment
has a lower page address and
- One of the endpoints is a Bulk IN and
- The other endpoint is an Interrupt IN
Then the Interrupt IN endpoint can end up not getting polled.
It is unclear what the precise failure mode is, as the controller seems to
haphazardly and repeatedly fetch TRBs for both endpoints but does not
advance the Interrupt endpoint transfer.
As a workaround, add a quirk that initially constrains all USB2.0 transfer
rings to a single segment in size. If for any reason a device driver queues
up enough outstanding transfers to fill the ring segment, then the ring
will be expanded. This has not been seen to occur with UMS or UVC drivers,
which aggressively queue buffers.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Don't calculate space based on the number of TRBs in the current segment,
as it's OK to wrap to the start (and flip the cycle state bit).
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
In a couple of error/incomplete configuration cases, the
DPI_FORMAT bits wouldn't get set.
Adopt a default of RGB666 in all these cases.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
DRM provides flags for inverting pixel clock and output enable
signals, but these were not mapped to the relevant registers.
Add those mappings.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The "panel-dpi" compatible string configures panel from device tree,
but it doesn't provide any way of configuring the bus format (colour
representation), nor does it populate it.
Add a DT parameter "bus-format" that allows the MEDIA_BUS_FMT_xxx value
to be specified from device tree.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
When using the "panel-dpi" compatible string, desc as passed
from DT is a dumy entry, and panel_dpi_probe allocates a new
one and attaches it to the panel.
However panel_simple_probe has already taken a local copy of
the variable, which means all the validation is done against
the empty dummy structure, not the configured data.
Update the local variable after panel_dpi_probe.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
panel-dpi doesn't know the bit depth, so in the same way that
DPI is guessed for the connector type, guess that it'll be 8bpc.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The clk-bcm2835 handling of the pixel clock does not function
correctly when the HDMI power domain is disabled.
The firmware supports it correctly, and the firmware clock
driver now supports it, so switch the vc4-hdmi driver to use
the firmware clock driver.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The clk-bcm2835 handling of the pixel clock does not function
correctly when the HDMI power domain is disabled.
The firmware supports it correctly, so add it to the
firmware clock driver.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Pi0-3 have power domains attached to the pm_runtime hooks
for the HDMI block. Initialisation done in the reset called
from bind is therefore lost if all users of the domain are
suspended.
The VEC shares the same lowest level clock/power gating as
the HDMI block, so whilst that is enabled the block is never
actually powered down, but if it isn't enabled then we lose
the state.
Reset and initialise the HDMI block from pm_resume.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The commit that changed from dev_err to dev_err_probe left the %d in the
format string, but removed the parameter, leading to a compile
warning.
Fixes: "6505412df625 drm/vc4: Use dev_err_probe when logging error registering HDMI audio"
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Register 0x02 in the FT5x06 is TD_STATUS containing the number
of valid touch points being reported.
Iterate over that number of points rather than all that are
supported on the device.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
This reverts commit 0c41710df5.
The regulator driver is now hopefully fixed, therefore revert the
workaround that dropped the I2C frequency.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The I2C to the Atmel is very fussy, and locks up easily on
Pi0-3 particularly on reads.
If running at 100kHz on Pi3, reading the ID register generally
locks up the Atmel, but splitting the register select write and
read into two transactions is reliable.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The I2C to the Atmel is very fussy, and locks up easily on
Pi0-3 particularly on reads.
The LCD power status is controlled solely by this driver, so
rather than reading it back from the Atmel, use the cached
status last set.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
commit 53af98c091 upstream.
Renoir and newer gfx9 APUs have new TSC register that is
not part of the gfxoff tile, so it can be read without
needing to disable gfx off.
Acked-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a48d96fd5 upstream.
Use __maybe_unused for noirq_suspend()/noirq_resume() hooks to avoid
build warning with !CONFIG_PM_SLEEP:
>> drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:796:12: error: 'stmmac_pltfr_noirq_resume' defined but not used [-Werror=unused-function]
796 | static int stmmac_pltfr_noirq_resume(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~
>> drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:775:12: error: 'stmmac_pltfr_noirq_suspend' defined but not used [-Werror=unused-function]
775 | static int stmmac_pltfr_noirq_suspend(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Fixes: 276aae3772 ("net: stmmac: fix system hang caused by eee_ctrl_timer during suspend/resume")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85b6d24646 upstream.
Currently, the exit_shm() function not designed to work properly when
task->sysvshm.shm_clist holds shm objects from different IPC namespaces.
This is a real pain when sysctl kernel.shm_rmid_forced = 1, because it
leads to use-after-free (reproducer exists).
This is an attempt to fix the problem by extending exit_shm mechanism to
handle shm's destroy from several IPC ns'es.
To achieve that we do several things:
1. add a namespace (non-refcounted) pointer to the struct shmid_kernel
2. during new shm object creation (newseg()/shmget syscall) we
initialize this pointer by current task IPC ns
3. exit_shm() fully reworked such that it traverses over all shp's in
task->sysvshm.shm_clist and gets IPC namespace not from current task
as it was before but from shp's object itself, then call
shm_destroy(shp, ns).
Note: We need to be really careful here, because as it was said before
(1), our pointer to IPC ns non-refcnt'ed. To be on the safe side we
using special helper get_ipc_ns_not_zero() which allows to get IPC ns
refcounter only if IPC ns not in the "state of destruction".
Q/A
Q: Why can we access shp->ns memory using non-refcounted pointer?
A: Because shp object lifetime is always shorther than IPC namespace
lifetime, so, if we get shp object from the task->sysvshm.shm_clist
while holding task_lock(task) nobody can steal our namespace.
Q: Does this patch change semantics of unshare/setns/clone syscalls?
A: No. It's just fixes non-covered case when process may leave IPC
namespace without getting task->sysvshm.shm_clist list cleaned up.
Link: https://lkml.kernel.org/r/67bb03e5-f79c-1815-e2bf-949c67047418@colorfullife.com
Link: https://lkml.kernel.org/r/20211109151501.4921-1-manfred@colorfullife.com
Fixes: ab602f7991 ("shm: make exit_shm work proportional to task activity")
Co-developed-by: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Alexander Mikhalitsyn <alexander.mikhalitsyn@virtuozzo.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Andrei Vagin <avagin@gmail.com>
Cc: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Cc: Vasily Averin <vvs@virtuozzo.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe3d100240 upstream.
We should not walk/touch page tables outside of VMA boundaries when
holding only the mmap sem in read mode. Evil user space can modify the
VMA layout just before this function runs and e.g., trigger races with
page table removal code since commit dd2283f260 ("mm: mmap: zap pages
with read mmap_sem in munmap"). gfn_to_hva() will only translate using
KVM memory regions, but won't validate the VMA.
Further, we should not allocate page tables outside of VMA boundaries: if
evil user space decides to map hugetlbfs to these ranges, bad things will
happen because we suddenly have PTE or PMD page tables where we
shouldn't have them.
Similarly, we have to check if we suddenly find a hugetlbfs VMA, before
calling get_locked_pte().
Fixes: 2d42f94773 ("s390/kvm: Add PGSTE manipulation functions")
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Link: https://lore.kernel.org/r/20210909162248.14969-4-david@redhat.com
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a884daa61a upstream.
Today netfront will trust the backend to send only sane response data.
In order to avoid privilege escalations or crashes in case of malicious
backends verify the data to be within expected limits. Especially make
sure that the response always references an outstanding request.
Note that only the tx queue needs special id handling, as for the rx
queue the id is equal to the index in the ring page.
Introduce a new indicator for the device whether it is broken and let
the device stop working when it is set. Set this indicator in case the
backend sets any weird data.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 21631d2d74 upstream.
The tx_skb_freelist elements are in a single linked list with the
request id used as link reference. The per element link field is in a
union with the skb pointer of an in use request.
Move the link reference out of the union in order to enable a later
reuse of it for requests which need a populated skb pointer.
Rename add_id_to_freelist() and get_id_from_freelist() to
add_id_to_list() and get_id_from_list() in order to prepare using
those for other lists as well. Define ~0 as value to indicate the end
of a list and place that value into the link for a request not being
on the list.
When freeing a skb zero the skb pointer in the request. Use a NULL
value of the skb pointer instead of skb_entry_is_link() for deciding
whether a request has a skb linked to it.
Remove skb_entry_set_link() and open code it instead as it is really
trivial now.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 162081ec33 upstream.
In order to avoid a malicious backend being able to influence the local
processing of a request build the request locally first and then copy
it to the ring page. Any reading from the request influencing the
processing in the frontend needs to be done on the local instance.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8446066bf8 upstream.
In order to avoid problems in case the backend is modifying a response
on the ring page while the frontend has already seen it, just read the
response into a local buffer in one go and then operate on that buffer
only.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b94e4b147f upstream.
Today blkfront will trust the backend to send only sane response data.
In order to avoid privilege escalations or crashes in case of malicious
backends verify the data to be within expected limits. Especially make
sure that the response always references an outstanding request.
Introduce a new state of the ring BLKIF_STATE_ERROR which will be
switched to in case an inconsistency is being detected. Recovering from
this state is possible only via removing and adding the virtual device
again (e.g. via a suspend/resume cycle).
Make all warning messages issued due to valid error responses rate
limited in order to avoid message floods being triggered by a malicious
backend.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Link: https://lore.kernel.org/r/20210730103854.12681-4-jgross@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 629a5d87e2 upstream.
Sync include/xen/interface/io/ring.h with Xen's newest version in
order to get the RING_COPY_RESPONSE() and RING_RESPONSE_PROD_OVERFLOW()
macros.
Note that this will correct the wrong license info by adding the
missing original copyright notice.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6cb206508b upstream.
When pid filtering is activated in an instance, all of the events trace
files for that instance has the PID_FILTER flag set. This determines
whether or not pid filtering needs to be done on the event, otherwise the
event is executed as normal.
If pid filtering is enabled when an event is created (via a dynamic event
or modules), its flag is not updated to reflect the current state, and the
events are not filtered properly.
Cc: stable@vger.kernel.org
Fixes: 3fdaf80f4a ("tracing: Implement event pid filtering")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 71e6864eac ]
Linux allows doing a flush/fsync on a file open for read-only,
but the protocol does not allow that. If the file passed in
on the flush is read-only try to find a writeable handle for
the same inode, if that is not possible skip sending the
fsync call to the server to avoid breaking the apps.
Reported-by: Julian Sikorski <belegdol@gmail.com>
Tested-by: Julian Sikorski <belegdol@gmail.com>
Suggested-by: Jeremy Allison <jra@samba.org>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8cfc0c7ed3 ]
ceph_statfs currently stuffs the cluster fsid into the f_fsid field.
This was fine when we only had a single filesystem per cluster, but now
that we have multiples we need to use something that will vary between
them.
Change ceph_statfs to xor each 32-bit chunk of the fsid (aka cluster id)
into the lower bits of the statfs->f_fsid. Change the lower bits to hold
the fscid (filesystem ID within the cluster).
That should give us a value that is guaranteed to be unique between
filesystems within a cluster, and should minimize the chance of
collisions between mounts of different clusters.
URL: https://tracker.ceph.com/issues/52812
Reported-by: Sachin Prabhu <sprabhu@redhat.com>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Xiubo Li <xiubli@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6663b138de ]
Inconsistent node block will cause a file fail to open or read,
which could make the user process crashes or stucks. Let's mark
SBI_NEED_FSCK flag to trigger a fix at next fsck time. After
unlinking the corrupted file, the user process could regenerate
a new one and work correctly.
Signed-off-by: Weichao Guo <guoweichao@oppo.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dce1ca0525 ]
To hot unplug a CPU, the idle task on that CPU calls a few layers of C
code before finally leaving the kernel. When KASAN is in use, poisoned
shadow is left around for each of the active stack frames, and when
shadow call stacks are in use. When shadow call stacks (SCS) are in use
the task's saved SCS SP is left pointing at an arbitrary point within
the task's shadow call stack.
When a CPU is offlined than onlined back into the kernel, this stale
state can adversely affect execution. Stale KASAN shadow can alias new
stackframes and result in bogus KASAN warnings. A stale SCS SP is
effectively a memory leak, and prevents a portion of the shadow call
stack being used. Across a number of hotplug cycles the idle task's
entire shadow call stack can become unusable.
We previously fixed the KASAN issue in commit:
e1b77c9298 ("sched/kasan: remove stale KASAN poison after hotplug")
... by removing any stale KASAN stack poison immediately prior to
onlining a CPU.
Subsequently in commit:
f1a0a376ca ("sched/core: Initialize the idle task with preemption disabled")
... the refactoring left the KASAN and SCS cleanup in one-time idle
thread initialization code rather than something invoked prior to each
CPU being onlined, breaking both as above.
We fixed SCS (but not KASAN) in commit:
63acd42c0d ("sched/scs: Reset the shadow stack when idle_task_exit")
... but as this runs in the context of the idle task being offlined it's
potentially fragile.
To fix these consistently and more robustly, reset the SCS SP and KASAN
shadow of a CPU's idle task immediately before we online that CPU in
bringup_cpu(). This ensures the idle task always has a consistent state
when it is running, and removes the need to so so when exiting an idle
task.
Whenever any thread is created, dup_task_struct() will give the task a
stack which is free of KASAN shadow, and initialize the task's SCS SP,
so there's no need to specially initialize either for idle thread within
init_idle(), as this was only necessary to handle hotplug cycles.
I've tested this on arm64 with:
* gcc 11.1.0, defconfig +KASAN_INLINE, KASAN_STACK
* clang 12.0.0, defconfig +KASAN_INLINE, KASAN_STACK, SHADOW_CALL_STACK
... offlining and onlining CPUS with:
| while true; do
| for C in /sys/devices/system/cpu/cpu*/online; do
| echo 0 > $C;
| echo 1 > $C;
| done
| done
Fixes: f1a0a376ca ("sched/core: Initialize the idle task with preemption disabled")
Reported-by: Qian Cai <quic_qiancai@quicinc.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Tested-by: Qian Cai <quic_qiancai@quicinc.com>
Link: https://lore.kernel.org/lkml/20211115113310.35693-1-mark.rutland@arm.com/
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0fecb289a ]
A prior patch increased the size of struct tcp_zerocopy_receive
but did not update do_tcp_getsockopt() handling to properly account
for this.
This patch simply reintroduces content erroneously cut from the
referenced prior patch that handles the new struct size.
Fixes: 18fb76ed53 ("net-zerocopy: Copy straggler unaligned data for TCP Rx. zerocopy.")
Signed-off-by: Arjun Roy <arjunroy@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c49a35eedf ]
The driver doesn't support RX timestamping for non-PTP packets, but it
declares that it does. Restrict the reported RX filters to PTP v2 over
L2 and over L4.
Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d2ad993aa ]
When PF is set to multi-TCs and configured mapping relationship between
priorities and TCs, the hardware will active these settings for this PF
and its VFs.
In this case when VF just uses one TC and its rx packets contain priority,
and if the priority is not mapped to TC0, as other TCs of VF is not valid,
hardware always put this kind of packets to the queue 0. It cause this kind
of packets of VF can not be used RSS function.
To fix this problem, set tc mode of all unused TCs of VF to the setting of
TC0, then rx packet with priority which map to unused TC will be direct to
TC0.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 01d9cc2dea ]
Inject error before dev_hold(real_dev) in register_vlan_dev(),
and execute the following testcase:
ip link add dev dummy1 type dummy
ip link add name dummy1.100 link dummy1 type vlan id 100
ip link del dev dummy1
When the dummy netdevice is removed, we will get a WARNING as following:
=======================================================================
refcount_t: decrement hit 0; leaking memory.
WARNING: CPU: 2 PID: 0 at lib/refcount.c:31 refcount_warn_saturate+0xbf/0x1e0
and an endless loop of:
=======================================================================
unregister_netdevice: waiting for dummy1 to become free. Usage count = -1073741824
That is because dev_put(real_dev) in vlan_dev_free() be called without
dev_hold(real_dev) in register_vlan_dev(). It makes the refcnt of real_dev
underflow.
Move the dev_hold(real_dev) to vlan_dev_init() which is the call-back of
ndo_init(). That makes dev_hold() and dev_put() for vlan's real_dev
symmetrical.
Fixes: 563bcbae3b ("net: vlan: fix a UAF in vlan_dev_real_dev()")
Reported-by: Petr Machata <petrm@nvidia.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Link: https://lore.kernel.org/r/20211126015942.2918542-1-william.xuanziyang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3911f73f5 ]
We replace proto_ops whenever TLS is configured for RX. But our
replacement also overrides sendpage_locked, which will crash
unless TX is also configured. Similarly we plug both of those
in for TLS_HW (NIC crypto offload) even tho TLS_HW has a completely
different implementation for TX.
Last but not least we always plug in something based on inet_stream_ops
even though a few of the callbacks differ for IPv6 (getname, release,
bind).
Use a callback building method similar to what we do for struct proto.
Fixes: c46234ebb4 ("tls: RX path for ktls")
Fixes: d4ffb02dee ("net/tls: enable sk_msg redirect to tls socket egress")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 520493f66f ]
We don't support splicing control records. TLS 1.3 changes moved
the record type check into the decrypt if(). The skb may already
be decrypted and still be an alert.
Note that decrypt_skb_update() is idempotent and updates ctx->decrypted
so the if() is pointless.
Reorder the check for decryption errors with the content type check
while touching them. This part is not really a bug, because if
decryption failed in TLS 1.3 content type will be DATA, and for
TLS 1.2 it will be correct. Nevertheless its strange to touch output
before checking if the function has failed.
Fixes: fedf201e12 ("net: tls: Refactor control message handling on recv")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41ce097f71 ]
It hangup when booting Loongson 3A1000 with BOTH
CONFIG_PAGE_SIZE_64KB and CONFIG_MIPS_VA_BITS_48, that it turn
out to use 2-level pgtable instead of 3-level. 64KB page size
with 2-level pgtable only cover 42 bits VA, use 3-level pgtable
to cover all 48 bits VA(55 bits)
Fixes: 1e321fa917 ("MIPS64: Support of at least 48 bits of SEGBITS)
Signed-off-by: Huang Pei <huangpei@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7db5e9e9e5 ]
It turns out that 'decode_configs' -> 'set_ftlb_enable' is called under
c->cputype unset, which leaves FTLB disabled on BOTH 3A2000 and 3A3000
Fix it by calling "decode_configs" after c->cputype is initialized
Fixes: da1bd29742 ("MIPS: Loongson64: Probe CPU features via CPUCFG")
Signed-off-by: Huang Pei <huangpei@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eaeace6077 ]
Oleksandr brought a bug report where netpoll causes trace
messages in the log on igb.
Danielle brought this back up as still occurring, so we'll try
again.
[22038.710800] ------------[ cut here ]------------
[22038.710801] igb_poll+0x0/0x1440 [igb] exceeded budget in poll
[22038.710802] WARNING: CPU: 12 PID: 40362 at net/core/netpoll.c:155 netpoll_poll_dev+0x18a/0x1a0
As Alex suggested, change the driver to return work_done at the
exit of napi_poll, which should be safe to do in this driver
because it is not polling multiple queues in this single napi
context (multiple queues attached to one MSI-X vector). Several
other drivers contain the same simple sequence, so I hope
this will not create new problems.
Fixes: 16eb8815c2 ("igb: Refactor clean_rx_irq to reduce overhead and improve performance")
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Reported-by: Danielle Ratson <danieller@nvidia.com>
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Tested-by: Danielle Ratson <danieller@nvidia.com>
Link: https://lore.kernel.org/r/20211123204000.1597971-1-jesse.brandeburg@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c024b226a4 ]
Submit I/O requests with the IOCB_NOWAIT flag set only if
the underlying filesystem supports it.
Fixes: 50a909db36 ("nvmet: use IOCB_NOWAIT for file-ns buffered I/O")
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ebb0c4b27 ]
The kernel_listen function in smc_listen will fail when all the available
ports are occupied. At this point smc->clcsock->sk->sk_data_ready has
been changed to smc_clcsock_data_ready. When we call smc_listen again,
now both smc->clcsock->sk->sk_data_ready and smc->clcsk_data_ready point
to the smc_clcsock_data_ready function.
The smc_clcsock_data_ready() function calls lsmc->clcsk_data_ready which
now points to itself resulting in an infinite loop.
This patch restores smc->clcsock->sk->sk_data_ready with the old value.
Fixes: a60a2b1e0a ("net/smc: reduce active tcp_listen workers")
Signed-off-by: Guo DaXing <guodaxing@huawei.com>
Acked-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 587acad41f ]
Coverity reports a possible NULL dereferencing problem:
in smc_vlan_by_tcpsk():
6. returned_null: netdev_lower_get_next returns NULL (checked 29 out of 30 times).
7. var_assigned: Assigning: ndev = NULL return value from netdev_lower_get_next.
1623 ndev = (struct net_device *)netdev_lower_get_next(ndev, &lower);
CID 1468509 (#1 of 1): Dereference null return value (NULL_RETURNS)
8. dereference: Dereferencing a pointer that might be NULL ndev when calling is_vlan_dev.
1624 if (is_vlan_dev(ndev)) {
Remove the manual implementation and use netdev_walk_all_lower_dev() to
iterate over the lower devices. While on it remove an obsolete function
parameter comment.
Fixes: cb9d43f677 ("net/smc: determine vlan_id of stacked net_device")
Suggested-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dbae3388ea ]
On mv88e6xxx 1G/2.5G PCS, the SerDes register 4.2001.2 has the following
description:
This register bit indicates when link was lost since the last
read. For the current link status, read this register
back-to-back.
Thus to get current link state, we need to read the register twice.
But doing that in the link change interrupt handler would lead to
potentially ignoring link down events, which we really want to avoid.
Thus this needs to be solved in phylink's resolve, by retriggering
another resolve in the event when PCS reports link down and previous
link was up, and by re-reading PCS state if the previous link was down.
The wrong value is read when phylink requests change from sgmii to
2500base-x mode, and link won't come up. This fixes the bug.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 80662f4fd4 ]
On PHY state change the phylink_resolve() function can read stale
information from the MAC and report incorrect link speed and duplex to
the kernel message log.
Example with a Marvell 88X3310 PHY connected to a SerDes port on Marvell
88E6393X switch:
- PHY driver triggers state change due to PHY interface mode being
changed from 10gbase-r to 2500base-x due to copper change in speed
from 10Gbps to 2.5Gbps, but the PHY itself either hasn't yet changed
its interface to the host, or the interrupt about loss of SerDes link
hadn't arrived yet (there can be a delay of several milliseconds for
this), so we still think that the 10gbase-r mode is up
- phylink_resolve()
- phylink_mac_pcs_get_state()
- this fills in speed=10g link=up
- interface mode is updated to 2500base-x but speed is left at 10Gbps
- phylink_major_config()
- interface is changed to 2500base-x
- phylink_link_up()
- mv88e6xxx_mac_link_up()
- .port_set_speed_duplex()
- speed is set to 10Gbps
- reports "Link is Up - 10Gbps/Full" to dmesg
Afterwards when the interrupt finally arrives for mv88e6xxx, another
resolve is forced in which we get the correct speed from
phylink_mac_pcs_get_state(), but since the interface is not being
changed anymore, we don't call phylink_major_config() but only
phylink_mac_config(), which does not set speed/duplex anymore.
To fix this, we need to force the link down and trigger another resolve
on PHY interface change event.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ddb826c2c9 ]
Usage of phy_ethtool_get_link_ksettings() in the link status change
handler isn't needed, and in combination with the referenced change
it results in a deadlock. Simply remove the call and replace it with
direct access to phydev->speed. The duplex argument of
lan743x_phy_update_flowcontrol() isn't used and can be removed.
Fixes: c10a485c3d ("phy: phy_ethtool_ksettings_get: Lock the phy for consistency")
Reported-by: Alessandro B Maurici <abmaurici@gmail.com>
Tested-by: Alessandro B Maurici <abmaurici@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/40e27f76-0ba3-dcef-ee32-a78b9df38b0f@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e1fddc98d ]
While testing BIG TCP patch series, I was expecting that TCP_RR workloads
with 80KB requests/answers would send one 80KB TSO packet,
then being received as a single GRO packet.
It turns out this was not happening, and the root cause was that
cubic Hystart ACK train was triggering after a few (2 or 3) rounds of RPC.
Hystart was wrongly setting CWND/SSTHRESH to 30, while my RPC
needed a budget of ~20 segments.
Ideally these TCP_RR flows should not exit slow start.
Cubic Hystart should reset itself at each round, instead of assuming
every TCP flow is a bulk one.
Note that even after this patch, Hystart can still trigger, depending
on scheduling artifacts, but at a higher CWND/SSTHRESH threshold,
keeping optimal TSO packet sizes.
Tested:
ip link set dev eth0 gro_ipv6_max_size 131072 gso_ipv6_max_size 131072
nstat -n; netperf -H ... -t TCP_RR -l 5 -- -r 80000,80000 -K cubic; nstat|egrep "Ip6InReceives|Hystart|Ip6OutRequests"
Before:
8605
Ip6InReceives 87541 0.0
Ip6OutRequests 129496 0.0
TcpExtTCPHystartTrainDetect 1 0.0
TcpExtTCPHystartTrainCwnd 30 0.0
After:
8760
Ip6InReceives 88514 0.0
Ip6OutRequests 87975 0.0
Fixes: ae27e98a51 ("[TCP] CUBIC v2.3")
Co-developed-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Link: https://lore.kernel.org/r/20211123202535.1843771-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21431f70f6 ]
[Why]
We're only setting the flags on stream[0]'s planes so this logic fails
if we have more than one stream in the state.
This can cause a page flip timeout with multiple displays in the
configuration.
[How]
Index into the stream_status array using the stream index - it's a 1:1
mapping.
Fixes: cdaae8371a ("drm/amd/display: Handle GPU reset for DC block")
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cefcf24b4d ]
Commit 39fbef4b0f ("PM: hibernate: Get block device exclusively in
swsusp_check()") changed the opening mode of the block device to
(FMODE_READ | FMODE_EXCL).
In the corresponding calls to swsusp_close(), the mode is still just
FMODE_READ which triggers the warning in blkdev_flush_mapping() on
resume from hibernate.
So, use the mode (FMODE_READ | FMODE_EXCL) also when closing the
device.
Fixes: 39fbef4b0f ("PM: hibernate: Get block device exclusively in swsusp_check()")
Signed-off-by: Thomas Zeitlhofer <thomas.zeitlhofer+lkml@ze-it.at>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac13285214 ]
Update NC-SI command handler (both standard and OEM) to take into
account of payload paddings in allocating skb (in case of payload
size is not 32-bit aligned).
The checksum field follows payload field, without taking payload
padding into account can cause checksum being truncated, leading to
dropped packets.
Fixes: fb4ee67529 ("net/ncsi: Add NCSI OEM command support")
Signed-off-by: Kumar Thangavel <thangavel.k@hcl.com>
Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 102110efdf ]
Current nvmet_try_send_ddgst() code does not check whether
all data digest bytes are transmitted, fix this by returning
-EAGAIN if all data digest bytes are not transmitted.
Fixes: 872d26a391 ("nvmet-tcp: add NVMe over TCP target driver")
Signed-off-by: Varun Prakash <varun@chelsio.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b1b62bc1e ]
Currently mvpp2_xdp_setup won't allow attaching XDP program if
mtu > ETH_DATA_LEN (1500).
The mvpp2_change_mtu on the other hand checks whether
MVPP2_RX_PKT_SIZE(mtu) > MVPP2_BM_LONG_PKT_SIZE.
These two checks are semantically different.
Moreover this limit can be increased to MVPP2_MAX_RX_BUF_SIZE, since in
mvpp2_rx we have
xdp.data = data + MVPP2_MH_SIZE + MVPP2_SKB_HEADROOM;
xdp.frame_sz = PAGE_SIZE;
Change the checks to check whether
mtu > MVPP2_MAX_RX_BUF_SIZE
Fixes: 07dd0a7aae ("mvpp2: add basic XDP support")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63b08b1f68 ]
When processing port up/down events generated by the device's firmware,
the driver protects itself from events reported for non-existent local
ports, but not the CPU port (local port 0), which exists, but lacks a
netdev.
This can result in a NULL pointer dereference when calling
netif_carrier_{on,off}().
Fix this by bailing early when processing an event reported for the CPU
port. Problem was only observed when running on top of a buggy emulator.
Fixes: 28b1987ef5 ("mlxsw: spectrum: Register CPU port with devlink")
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 837ec05cfe ]
There are few cases in which an array index queried from a fw register,
is accessed without any validation that it doesn't exceed the array
length.
Add a proper length validation, so accessing memory past the end of an
array will be forbidden.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 606a63c978 ]
The side that actively closed socket, it's clcsock doesn't enter
TIME_WAIT state, but the passive side does it. It should show the same
behavior as TCP sockets.
Consider this, when client actively closes the socket, the clcsock in
server enters TIME_WAIT state, which means the address is occupied and
won't be reused before TIME_WAIT dismissing. If we restarted server, the
service would be unavailable for a long time.
To solve this issue, shutdown the clcsock in [A], perform the TCP active
close progress first, before the passive closed side closing it. So that
the actively closed side enters TIME_WAIT, not the passive one.
Client | Server
close() // client actively close |
smc_release() |
smc_close_active() // PEERCLOSEWAIT1 |
smc_close_final() // abort or closed = 1|
smc_cdc_get_slot_and_msg_send() |
[A] |
|smc_cdc_msg_recv_action() // ACTIVE
| queue_work(smc_close_wq, &conn->close_work)
| smc_close_passive_work() // PROCESSABORT or APPCLOSEWAIT1
| smc_close_passive_abort_received() // only in abort
|
|close() // server recv zero, close
| smc_release() // PROCESSABORT or APPCLOSEWAIT1
| smc_close_active()
| smc_close_abort() or smc_close_final() // CLOSED
| smc_cdc_get_slot_and_msg_send() // abort or closed = 1
smc_cdc_msg_recv_action() | smc_clcsock_release()
queue_work(smc_close_wq, &conn->close_work) | sock_release(tcp) // actively close clc, enter TIME_WAIT
smc_close_passive_work() // PEERCLOSEWAIT1 | smc_conn_free()
smc_close_passive_abort_received() // CLOSED|
smc_conn_free() |
smc_clcsock_release() |
sock_release(tcp) // passive close clc |
Link: https://www.spinics.net/lists/netdev/msg780407.html
Fixes: b38d732477 ("smc: socket closing and linkgroup cleanup")
Signed-off-by: Tony Lu <tonylu@linux.alibaba.com>
Reviewed-by: Wen Gu <guwen@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57bbeacdbe ]
We observed the following deadlock in the stress test under low
memory scenario:
Thread A Thread B
- erofs_shrink_scan
- erofs_try_to_release_workgroup
- erofs_workgroup_try_to_freeze -- A
- z_erofs_do_read_page
- z_erofs_collection_begin
- z_erofs_register_collection
- erofs_insert_workgroup
- xa_lock(&sbi->managed_pslots) -- B
- erofs_workgroup_get
- erofs_wait_on_workgroup_freezed -- A
- xa_erase
- xa_lock(&sbi->managed_pslots) -- B
To fix this, it needs to hold xa_lock before freezing the workgroup
since xarray will be touched then. So let's hold the lock before
accessing each workgroup, just like what we did with the radix tree
before.
[ Gao Xiang: Jianhua Hao also reports this issue at
https://lore.kernel.org/r/b10b85df30694bac8aadfe43537c897a@xiaomi.com ]
Link: https://lore.kernel.org/r/20211118135844.3559-1-huangjianan@oppo.com
Fixes: 64094a0441 ("erofs: convert workstn to XArray")
Reviewed-by: Chao Yu <chao@kernel.org>
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Huang Jianan <huangjianan@oppo.com>
Reported-by: Jianhua Hao <haojianhua1@xiaomi.com>
Signed-off-by: Gao Xiang <xiang@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1005f19b93 ]
When replacing a nexthop group, we must release the IPv6 per-cpu dsts of
the removed nexthop entries after an RCU grace period because they
contain references to the nexthop's net device and to the fib6 info.
With specific series of events[1] we can reach net device refcount
imbalance which is unrecoverable. IPv4 is not affected because dsts
don't take a refcount on the route.
[1]
$ ip nexthop list
id 200 via 2002:db8::2 dev bridge.10 scope link onlink
id 201 via 2002:db8::3 dev bridge scope link onlink
id 203 group 201/200
$ ip -6 route
2001:db8::10 nhid 203 metric 1024 pref medium
nexthop via 2002:db8::3 dev bridge weight 1 onlink
nexthop via 2002:db8::2 dev bridge.10 weight 1 onlink
Create rt6_info through one of the multipath legs, e.g.:
$ taskset -a -c 1 ./pkt_inj 24 bridge.10 2001:db8::10
(pkt_inj is just a custom packet generator, nothing special)
Then remove that leg from the group by replace (let's assume it is id
200 in this case):
$ ip nexthop replace id 203 group 201
Now remove the IPv6 route:
$ ip -6 route del 2001:db8::10/128
The route won't be really deleted due to the stale rt6_info holding 1
refcnt in nexthop id 200.
At this point we have the following reference count dependency:
(deleted) IPv6 route holds 1 reference over nhid 203
nh 203 holds 1 ref over id 201
nh 200 holds 1 ref over the net device and the route due to the stale
rt6_info
Now to create circular dependency between nh 200 and the IPv6 route, and
also to get a reference over nh 200, restore nhid 200 in the group:
$ ip nexthop replace id 203 group 201/200
And now we have a permanent circular dependncy because nhid 203 holds a
reference over nh 200 and 201, but the route holds a ref over nh 203 and
is deleted.
To trigger the bug just delete the group (nhid 203):
$ ip nexthop del id 203
It won't really be deleted due to the IPv6 route dependency, and now we
have 2 unlinked and deleted objects that reference each other: the group
and the IPv6 route. Since the group drops the reference it holds over its
entries at free time (i.e. its own refcount needs to drop to 0) that will
never happen and we get a permanent ref on them, since one of the entries
holds a reference over the IPv6 route it will also never be released.
At this point the dependencies are:
(deleted, only unlinked) IPv6 route holds reference over group nh 203
(deleted, only unlinked) group nh 203 holds reference over nh 201 and 200
nh 200 holds 1 ref over the net device and the route due to the stale
rt6_info
This is the last point where it can be fixed by running traffic through
nh 200, and specifically through the same CPU so the rt6_info (dst) will
get released due to the IPv6 genid, that in turn will free the IPv6
route, which in turn will free the ref count over the group nh 203.
If nh 200 is deleted at this point, it will never be released due to the
ref from the unlinked group 203, it will only be unlinked:
$ ip nexthop del id 200
$ ip nexthop
$
Now we can never release that stale rt6_info, we have IPv6 route with ref
over group nh 203, group nh 203 with ref over nh 200 and 201, nh 200 with
rt6_info (dst) with ref over the net device and the IPv6 route. All of
these objects are only unlinked, and cannot be released, thus they can't
release their ref counts.
Message from syslogd@dev at Nov 19 14:04:10 ...
kernel:[73501.828730] unregister_netdevice: waiting for bridge.10 to become free. Usage count = 3
Message from syslogd@dev at Nov 19 14:04:20 ...
kernel:[73512.068811] unregister_netdevice: waiting for bridge.10 to become free. Usage count = 3
Fixes: 7bf4796dd0 ("nexthops: add support for replace")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8837cbbf85 ]
We need a way to release a fib6_nh's per-cpu dsts when replacing
nexthops otherwise we can end up with stale per-cpu dsts which hold net
device references, so add a new IPv6 stub called fib6_nh_release_dsts.
It must be used after an RCU grace period, so no new dsts can be created
through a group's nexthop entry.
Similar to fib6_nh_release it shouldn't be used if fib6_nh_init has failed
so it doesn't need a dummy stub when IPv6 is not enabled.
Fixes: 7bf4796dd0 ("nexthops: add support for replace")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6da2bbb00 ]
Currently, when user space emits SIOCSHWTSTAMP ioctl calls such as
enabling/disabling timestamping or changing filter settings, the driver
reads the current CLOCK_REALTIME value and programming this into the
NIC's hardware clock. This might be necessary during system
initialization, but at runtime, when the PTP clock has already been
synchronized to a grandmaster, a reset of the timestamp settings might
result in a clock jump. Furthermore, if the clock is also controlled by
phc2sys in automatic mode (where the UTC offset is queried from ptp4l),
that UTC-to-TAI offset (currently 37 seconds in 2021) would be
temporarily reset to 0, and it would take a long time for phc2sys to
readjust so that CLOCK_REALTIME and the PHC are apart by 37 seconds
again.
To address the issue, we introduce a new function called
stmmac_init_tstamp_counter(), which gets called during ndo_open().
It contains the code snippet moved from stmmac_hwtstamp_set() that
manages the time synchronization. Besides, the sub second increment
configuration is also moved here since the related values are hardware
dependent and runtime invariant.
Furthermore, the hardware clock must be kept running even when no time
stamping mode is selected in order to retain the synchronized time base.
That way, timestamping can be enabled again at any time only with the
need to compensate the clock's natural drifting.
As a side effect, this patch fixes the issue that ptp_clock_info::enable
can be called before SIOCSHWTSTAMP and the driver (which looks at
priv->systime_flags) was not prepared to handle that ordering.
Fixes: 92ba688851 ("stmmac: add the support for PTP hw clock driver")
Reported-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Holger Assmann <h.assmann@pengutronix.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 276aae3772 ]
commit 5f58591323 ("net: stmmac: delete the eee_ctrl_timer after
napi disabled"), this patch tries to fix system hang caused by eee_ctrl_timer,
unfortunately, it only can resolve it for system reboot stress test. System
hang also can be reproduced easily during system suspend/resume stess test
when mount NFS on i.MX8MP EVK board.
In stmmac driver, eee feature is combined to phylink framework. When do
system suspend, phylink_stop() would queue delayed work, it invokes
stmmac_mac_link_down(), where to deactivate eee_ctrl_timer synchronizly.
In above commit, try to fix issue by deactivating eee_ctrl_timer obviously,
but it is not enough. Looking into eee_ctrl_timer expire callback
stmmac_eee_ctrl_timer(), it could enable hareware eee mode again. What is
unexpected is that LPI interrupt (MAC_Interrupt_Enable.LPIEN bit) is always
asserted. This interrupt has chance to be issued when LPI state entry/exit
from the MAC, and at that time, clock could have been already disabled.
The result is that system hang when driver try to touch register from
interrupt handler.
The reason why above commit can fix system hang issue in stmmac_release()
is that, deactivate eee_ctrl_timer not just after napi disabled, further
after irq freed.
In conclusion, hardware would generate LPI interrupt when clock has been
disabled during suspend or resume, since hardware is in eee mode and LPI
interrupt enabled.
Interrupts from MAC, MTL and DMA level are enabled and never been disabled
when system suspend, so postpone clocks management from suspend stage to
noirq suspend stage should be more safe.
Fixes: 5f58591323 ("net: stmmac: delete the eee_ctrl_timer after napi disabled")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3bd6b2a838 ]
Use nn->tlv_caps.me_freq_mhz instead of nn->me_freq_mhz to check whether
rx-usecs/tx-usecs is valid.
This is because nn->tlv_caps.me_freq_mhz represents the clock_freq (MHz) of
the flow processing cores (FPC) on the NIC. While nn->me_freq_mhz is not
be set.
Fixes: ce991ab666 ("nfp: read ME frequency from vNIC ctrl memory")
Signed-off-by: Diana Wang <na.wang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e95d8eaee2 ]
The ARCH_FEATURES function ID is a 32-bit SMC call, which returns
a 32-bit result per the SMCCC spec. Current code is doing a 64-bit
comparison against -1 (SMCCC_RET_NOT_SUPPORTED) to detect that the
feature is unimplemented. That check doesn't work in a Hyper-V VM,
where the upper 32-bits are zero as allowed by the spec.
Cast the result as an 'int' so the comparison works. The change also
makes the code consistent with other similar checks in this file.
Fixes: 821b67fa46 ("firmware: smccc: Add ARCH_SOC_ID support")
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee50e67ba0 ]
To compute the rtx timeout schedule_3rdack_retransmission() does multiple
things in the wrong way: srtt_us is measured in usec/8 and the timeout
itself is an absolute value.
Fixes: ec3edaa7ca ("mptcp: Add handling of outgoing MP_JOIN requests")
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <mathew.j.martineau>@linux.intel.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e792779e6b ]
Resolve being able to change static values on VF when adaptive interrupt
moderation is enabled.
This problem is fixed by checking the interrupt settings is not
a combination of change of static value while adaptive interrupt
moderation is turned on.
Without this fix, the user would be able to change static values
on VF with adaptive moderation enabled.
Fixes: 65e87c0398 ("i40evf: support queue-specific settings for interrupt moderation")
Signed-off-by: Nitesh B Venkatesh <nitesh.b.venkatesh@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ee4ba13e0 ]
While looping over shost's sdev list it is possible that one
of the drives is getting removed and its sas_target object is
freed but its sdev object remains intact.
Consequently, a kernel panic can occur while the driver is trying to access
the sas_address field of sas_target object without also checking the
sas_target object for NULL.
Link: https://lore.kernel.org/r/20211117104909.2069-1-sreekanth.reddy@broadcom.com
Fixes: f92363d123 ("[SCSI] mpt3sas: add new driver supporting 12GB SAS")
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3c45824ad ]
The failure to retrieve post-op attributes has no bearing on whether or
not the clone operation itself was successful. We must therefore ignore
the return value of decode_getfattr() when looking at the success or
failure of nfs4_xdr_dec_clone().
Fixes: 36022770de ("nfs42: add CLONE xdr functions")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 451dc48c80 ]
This patch fixes an issue that an u32 netlink value is handled as a
signed enum value which doesn't fit into the range of u32 netlink type.
If it's handled as -1 value some BIT() evaluation ends in a
shift-out-of-bounds issue. To solve the issue we set the to u32 max which
is s32 "-1" value to keep backwards compatibility and let the followed enum
values start counting at 0. This brings the compiler to never handle the
enum as signed and a check if the value is above NL802154_IFTYPE_MAX should
filter -1 out.
Fixes: f3ea5e4423 ("ieee802154: add new interface command")
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20211112030916.685793-1-aahringo@redhat.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 861afeac79 ]
Stream IDs are reused across multiple BackEnd mixers, do not reset the
stream mixers if they are not already set for that particular FrontEnd.
Ex:
amixer cset iface=MIXER,name='SLIMBUS_0_RX Audio Mixer MultiMedia1' 1
would set the MultiMedia1 steam for SLIMBUS_0_RX, however doing below
command will reset previously setup MultiMedia1 stream, because both of them
are using MultiMedia1 PCM stream.
amixer cset iface=MIXER,name='SLIMBUS_2_RX Audio Mixer MultiMedia1' 0
reset the FrontEnd Mixers conditionally to fix this issue.
This is more noticeable in desktop setup, where in alsactl tries to restore
the alsa state and overwriting the previous mixer settings.
Fixes: e3a33673e8 ("ASoC: qdsp6: q6routing: Add q6routing driver")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20211116114721.12517-3-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 98481f3d72 ]
The PCIe host bridge has two interrupt lines, one that goes towards it
PCIE_INTR2 second level interrupt controller and one for its MSI second
level interrupt controller. The first interrupt line is not currently
managed by the driver, which is why it was not a functional problem.
The interrupt-map property was also only listing the PCI_INTA interrupts
when there are also the INTB, C and D.
Reported-by: Jim Quinlan <jim2101024@gmail.com>
Fixes: d5c8dc0d4c ("ARM: dts: bcm2711: Enable PCIe controller")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 40f7342f05 ]
The GPIO controller is also an interrupt controller provider and is
currently missing the appropriate 'interrupt-controller' and
'#interrupt-cells' properties to denote that.
Fixes: fb026d3de3 ("ARM: BCM5301X: Add Broadcom's bus-axi to the DTS file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 754c4050a0 ]
The I2C interrupt controller line is off by 32 because the datasheet
describes interrupt inputs into the GIC which are for Shared Peripheral
Interrupts and are starting at offset 32. The ARM GIC binding expects
the SPI interrupts to be numbered from 0 relative to the SPI base.
Fixes: bb097e3e00 ("ARM: dts: BCM5301X: Add I2C support to the DT")
Tested-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39f6eed4cb ]
Previously the IPv6 addresses in the key were clobbered and the mask was
left unset.
I haven't tested this; I noticed it while skimming the code to
understand an unrelated issue.
Fixes: cfab6dbd0e ("netfilter: flowtable: add tunnel match offload support")
Cc: wenxu <wenxu@ucloud.cn>
Signed-off-by: Will Mortensen <willmo@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c95c07836f ]
We are changing expire_nodest_conn to work even for reused connections when
conn_reuse_mode=0, just as what was done with commit dc7b3eb900 ("ipvs:
Fix reuse connection if real server is dead").
For controlled and persistent connections, the new connection will get the
needed real server depending on the rules in ip_vs_check_template().
Fixes: d752c36457 ("ipvs: allow rescheduling of new connections when port reuse is detected")
Co-developed-by: Chuanqi Liu <legend050709@qq.com>
Signed-off-by: Chuanqi Liu <legend050709@qq.com>
Signed-off-by: yangxingwu <xingwu.yang@gmail.com>
Acked-by: Simon Horman <horms@verge.net.au>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77522ff02f ]
And be consistent in error management for both orig/reply filtering
Fixes: cb8aa9a3af ("netfilter: ctnetlink: add kernel side filtering for dump")
Signed-off-by: Florent Fourcot <florent.fourcot@wifirst.fr>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c1e6311771 upstream.
To clear a user buffer we cannot simply use memset, we have to use
clear_user(). With a virtio-mem device that registers a vmcore_cb and
has some logically unplugged memory inside an added Linux memory block,
I can easily trigger a BUG by copying the vmcore via "cp":
systemd[1]: Starting Kdump Vmcore Save Service...
kdump[420]: Kdump is using the default log level(3).
kdump[453]: saving to /sysroot/var/crash/127.0.0.1-2021-11-11-14:59:22/
kdump[458]: saving vmcore-dmesg.txt to /sysroot/var/crash/127.0.0.1-2021-11-11-14:59:22/
kdump[465]: saving vmcore-dmesg.txt complete
kdump[467]: saving vmcore
BUG: unable to handle page fault for address: 00007f2374e01000
#PF: supervisor write access in kernel mode
#PF: error_code(0x0003) - permissions violation
PGD 7a523067 P4D 7a523067 PUD 7a528067 PMD 7a525067 PTE 800000007048f867
Oops: 0003 [#1] PREEMPT SMP NOPTI
CPU: 0 PID: 468 Comm: cp Not tainted 5.15.0+ #6
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.14.0-27-g64f37cc530f1-prebuilt.qemu.org 04/01/2014
RIP: 0010:read_from_oldmem.part.0.cold+0x1d/0x86
Code: ff ff ff e8 05 ff fe ff e9 b9 e9 7f ff 48 89 de 48 c7 c7 38 3b 60 82 e8 f1 fe fe ff 83 fd 08 72 3c 49 8d 7d 08 4c 89 e9 89 e8 <49> c7 45 00 00 00 00 00 49 c7 44 05 f8 00 00 00 00 48 83 e7 f81
RSP: 0018:ffffc9000073be08 EFLAGS: 00010212
RAX: 0000000000001000 RBX: 00000000002fd000 RCX: 00007f2374e01000
RDX: 0000000000000001 RSI: 00000000ffffdfff RDI: 00007f2374e01008
RBP: 0000000000001000 R08: 0000000000000000 R09: ffffc9000073bc50
R10: ffffc9000073bc48 R11: ffffffff829461a8 R12: 000000000000f000
R13: 00007f2374e01000 R14: 0000000000000000 R15: ffff88807bd421e8
FS: 00007f2374e12140(0000) GS:ffff88807f000000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f2374e01000 CR3: 000000007a4aa000 CR4: 0000000000350eb0
Call Trace:
read_vmcore+0x236/0x2c0
proc_reg_read+0x55/0xa0
vfs_read+0x95/0x190
ksys_read+0x4f/0xc0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
Some x86-64 CPUs have a CPU feature called "Supervisor Mode Access
Prevention (SMAP)", which is used to detect wrong access from the kernel
to user buffers like this: SMAP triggers a permissions violation on
wrong access. In the x86-64 variant of clear_user(), SMAP is properly
handled via clac()+stac().
To fix, properly use clear_user() when we're dealing with a user buffer.
Link: https://lkml.kernel.org/r/20211112092750.6921-1-david@redhat.com
Fixes: 997c136f51 ("fs/proc/vmcore.c: add hook to read_from_oldmem() to check for non-ram pages")
Signed-off-by: David Hildenbrand <david@redhat.com>
Acked-by: Baoquan He <bhe@redhat.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Philipp Rudo <prudo@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f76b36d40b upstream.
Fix multiple link training issues in aardvark driver. The main reason of
these issues was misunderstanding of what certain registers do, since their
names and comments were misleading: before commit 96be36dbff ("PCI:
aardvark: Replace custom macros by standard linux/pci_regs.h macros"), the
pci-aardvark.c driver used custom macros for accessing standard PCIe Root
Bridge registers, and misleading comments did not help to understand what
the code was really doing.
After doing more tests and experiments I've come to the conclusion that the
SPEED_GEN register in aardvark sets the PCIe revision / generation
compliance and forces maximal link speed. Both GEN3 and GEN2 values set the
read-only PCI_EXP_FLAGS_VERS bits (PCIe capabilities version of Root
Bridge) to value 2, while GEN1 value sets PCI_EXP_FLAGS_VERS to 1, which
matches with PCI Express specifications revisions 3, 2 and 1 respectively.
Changing SPEED_GEN also sets the read-only bits PCI_EXP_LNKCAP_SLS and
PCI_EXP_LNKCAP2_SLS to corresponding speed.
(Note that PCI Express rev 1 specification does not define PCI_EXP_LNKCAP2
and PCI_EXP_LNKCTL2 registers and when SPEED_GEN is set to GEN1 (which
also sets PCI_EXP_FLAGS_VERS set to 1), lspci cannot access
PCI_EXP_LNKCAP2 and PCI_EXP_LNKCTL2 registers.)
Changing PCIe link speed can be done via PCI_EXP_LNKCTL2_TLS bits of
PCI_EXP_LNKCTL2 register. Armada 3700 Functional Specifications says that
the default value of PCI_EXP_LNKCTL2_TLS is based on SPEED_GEN value, but
tests showed that the default value is always 8.0 GT/s, independently of
speed set by SPEED_GEN. So after setting SPEED_GEN, we must also set value
in PCI_EXP_LNKCTL2 register via PCI_EXP_LNKCTL2_TLS bits.
Triggering PCI_EXP_LNKCTL_RL bit immediately after setting LINK_TRAINING_EN
bit actually doesn't do anything. Tests have shown that a delay is needed
after enabling LINK_TRAINING_EN bit. As triggering PCI_EXP_LNKCTL_RL
currently does nothing, remove it.
Commit 43fc679ced ("PCI: aardvark: Improve link training") introduced
code which sets SPEED_GEN register based on negotiated link speed from
PCI_EXP_LNKSTA_CLS bits of PCI_EXP_LNKSTA register. This code was added to
fix detection of Compex WLE900VX (Atheros QCA9880) WiFi GEN1 PCIe cards, as
otherwise these cards were "invisible" on PCIe bus (probably because they
crashed). But apparently more people reported the same issues with these
cards also with other PCIe controllers [1] and I was able to reproduce this
issue also with other "noname" WiFi cards based on Atheros QCA9890 chip
(with the same PCI vendor/device ids as Atheros QCA9880). So this is not an
issue in aardvark but rather an issue in Atheros QCA98xx chips. Also, this
issue only exists if the kernel is compiled with PCIe ASPM support, and a
generic workaround for this is to change PCIe Bridge to 2.5 GT/s link speed
via PCI_EXP_LNKCTL2_TLS_2_5GT bits in PCI_EXP_LNKCTL2 register [2], before
triggering PCI_EXP_LNKCTL_RL bit. This workaround also works when SPEED_GEN
is set to value GEN2 (5 GT/s). So remove this hack completely in the
aardvark driver and always set SPEED_GEN to value from 'max-link-speed' DT
property. Fix for Atheros QCA98xx chips is handled separately by patch [2].
These two things (code for triggering PCI_EXP_LNKCTL_RL bit and changing
SPEED_GEN value) also explain why commit 6964494582 ("PCI: aardvark:
Train link immediately after enabling training") somehow fixed detection of
those problematic Compex cards with Atheros chips: if triggering link
retraining (via PCI_EXP_LNKCTL_RL bit) was done immediately after enabling
link training (via LINK_TRAINING_EN), it did nothing. If there was a
specific delay, aardvark HW already initialized PCIe link and therefore
triggering link retraining caused the above issue. Compex cards triggered
link down event and disappeared from the PCIe bus.
Commit f4c7d053d7 ("PCI: aardvark: Wait for endpoint to be ready before
training link") added 100ms sleep before calling 'Start link training'
command and explained that it is a requirement of PCI Express
specification. But the code after this 100ms sleep was not doing 'Start
link training', rather it triggered PCI_EXP_LNKCTL_RL bit via PCIe Root
Bridge to put link into Recovery state.
The required delay after fundamental reset is already done in function
advk_pcie_wait_for_link() which also checks whether PCIe link is up.
So after removing the code which triggers PCI_EXP_LNKCTL_RL bit on PCIe
Root Bridge, there is no need to wait 100ms again. Remove the extra
msleep() call and update comment about the delay required by the PCI
Express specification.
According to Marvell Armada 3700 Functional Specifications, Link training
should be enabled via aardvark register LINK_TRAINING_EN after selecting
PCIe generation and x1 lane. There is no need to disable it prior resetting
card via PERST# signal. This disabling code was introduced in commit
5169a9851d ("PCI: aardvark: Issue PERST via GPIO") as a workaround for
some Atheros cards. It turns out that this also is Atheros specific issue
and affects any PCIe controller, not only aardvark. Moreover this Atheros
issue was triggered by juggling with PCI_EXP_LNKCTL_RL, LINK_TRAINING_EN
and SPEED_GEN bits interleaved with sleeps. Now, after removing triggering
PCI_EXP_LNKCTL_RL, there is no need to explicitly disable LINK_TRAINING_EN
bit. So remove this code too. The problematic Compex cards described in
previous git commits are correctly detected in advk_pcie_train_link()
function even after applying all these changes.
Note that with this patch, and also prior this patch, some NVMe disks which
support PCIe GEN3 with 8 GT/s speed are negotiated only at the lowest link
speed 2.5 GT/s, independently of SPEED_GEN value. After manually triggering
PCI_EXP_LNKCTL_RL bit (e.g. from userspace via setpci), these NVMe disks
change link speed to 5 GT/s when SPEED_GEN was configured to GEN2. This
issue first needs to be properly investigated. I will send a fix in the
future.
On the other hand, some other GEN2 PCIe cards with 5 GT/s speed are
autonomously by HW autonegotiated at full 5 GT/s speed without need of any
software interaction.
Armada 3700 Functional Specifications describes the following steps for
link training: set SPEED_GEN to GEN2, enable LINK_TRAINING_EN, poll until
link training is complete, trigger PCI_EXP_LNKCTL_RL, poll until signal
rate is 5 GT/s, poll until link training is complete, enable ASPM L0s.
The requirement for triggering PCI_EXP_LNKCTL_RL can be explained by the
need to achieve 5 GT/s speed (as changing link speed is done by throw to
recovery state entered by PCI_EXP_LNKCTL_RL) or maybe as a part of enabling
ASPM L0s (but in this case ASPM L0s should have been enabled prior
PCI_EXP_LNKCTL_RL).
It is unknown why the original pci-aardvark.c driver was triggering
PCI_EXP_LNKCTL_RL bit before waiting for the link to be up. This does not
align with neither PCIe base specifications nor with Armada 3700 Functional
Specification. (Note that in older versions of aardvark, this bit was
called incorrectly PCIE_CORE_LINK_TRAINING, so this may be the reason.)
It is also unknown why Armada 3700 Functional Specification says that it is
needed to trigger PCI_EXP_LNKCTL_RL for GEN2 mode, as according to PCIe
base specification 5 GT/s speed negotiation is supposed to be entirely
autonomous, even if initial speed is 2.5 GT/s.
[1] - https://lore.kernel.org/linux-pci/87h7l8axqp.fsf@toke.dk/
[2] - https://lore.kernel.org/linux-pci/20210326124326.21163-1-pali@kernel.org/
Link: https://lore.kernel.org/r/20211005180952.6812-12-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 223dec14a0 upstream.
Commit 43f5c77bcb ("PCI: aardvark: Fix reporting CRS value") fixed
handling of CRS response and when CRSSVE flag was not enabled it marked CRS
response as failed transaction (due to simplicity).
But pci-aardvark.c driver is already waiting up to the PIO_RETRY_CNT count
for PIO config response and so we can with a small change implement
re-issuing of config requests as described in PCIe base specification.
This change implements re-issuing of config requests when response is CRS.
Set upper bound of wait cycles to around PIO_RETRY_CNT, afterwards the
transaction is marked as failed and an all-ones value is returned as
before.
We do this by returning appropriate error codes from function
advk_pcie_check_pio_status(). On CRS we return -EAGAIN and caller then
reissues transaction.
Link: https://lore.kernel.org/r/20211005180952.6812-10-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a55f224ff5 upstream.
If a event is filtered by pid and a trigger that requires processing of
the event to happen is a attached to the event, the discard portion does
not take the pid filtering into account, and the event will then be
recorded when it should not have been.
Cc: stable@vger.kernel.org
Fixes: 3fdaf80f4a ("tracing: Implement event pid filtering")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cf0b0e3712 upstream.
The POWER9 ERAT flush instruction is a SLBIA with IH=7, which is a
reserved value on POWER7/8. On POWER8 this invalidates the SLB entries
above index 0, similarly to SLBIA IH=0.
If the SLB entries are invalidated, and then the guest is bypassed, the
host SLB does not get re-loaded, so the bolted entries above 0 will be
lost. This can result in kernel stack access causing a SLB fault.
Kernel stack access causing a SLB fault was responsible for the infamous
mega bug (search "Fix SLB reload bug"). Although since commit
48e7b76957 ("powerpc/64s/hash: Convert SLB miss handlers to C") that
starts using the kernel stack in the SLB miss handler, it might only
result in an infinite loop of SLB faults. In any case it's a bug.
Fix this by only executing the instruction on >= POWER9 where IH=7 is
defined not to invalidate the SLB. POWER7/8 don't require this ERAT
flush.
Fixes: 5008711259 ("KVM: PPC: Book3S HV: Invalidate ERAT when flushing guest TLB entries")
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211119031627.577853-1-npiggin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 36e8f60f08 upstream.
If the xenstore page hasn't been allocated properly, reading the value
of the related hvm_param (HVM_PARAM_STORE_PFN) won't actually return
error. Instead, it will succeed and return zero. Instead of attempting
to xen_remap a bad guest physical address, detect this condition and
return early.
Note that although a guest physical address of zero for
HVM_PARAM_STORE_PFN is theoretically possible, it is not a good choice
and zero has never been validly used in that capacity.
Also recognize all bits set as an invalid value.
For 32-bit Linux, any pfn above ULONG_MAX would get truncated. Pfns
above ULONG_MAX should never be passed by the Xen tools to HVM guests
anyway, so check for this condition and return early.
Cc: stable@vger.kernel.org
Signed-off-by: Stefano Stabellini <stefano.stabellini@xilinx.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Link: https://lore.kernel.org/r/20211123210748.1910236-1-sstabellini@kernel.org
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08f6c2b09e upstream.
In case of errors in xenbus_init (e.g. missing xen_store_gfn parameter),
we goto out_error but we forget to reset xen_store_domain_type to
XS_UNKNOWN. As a consequence xenbus_probe_initcall and other initcalls
will still try to initialize xenstore resulting into a crash at boot.
[ 2.479830] Call trace:
[ 2.482314] xb_init_comms+0x18/0x150
[ 2.486354] xs_init+0x34/0x138
[ 2.489786] xenbus_probe+0x4c/0x70
[ 2.498432] xenbus_probe_initcall+0x2c/0x7c
[ 2.503944] do_one_initcall+0x54/0x1b8
[ 2.507358] kernel_init_freeable+0x1ac/0x210
[ 2.511617] kernel_init+0x28/0x130
[ 2.516112] ret_from_fork+0x10/0x20
Cc: <Stable@vger.kernel.org>
Cc: jbeulich@suse.com
Signed-off-by: Stefano Stabellini <stefano.stabellini@xilinx.com>
Link: https://lore.kernel.org/r/20211115222719.2558207-1-sstabellini@kernel.org
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 473441720c upstream.
Checking buf->flags should be done before the pipe_buf_release() is called
on the pipe buffer, since releasing the buffer might modify the flags.
This is exactly what page_cache_pipe_buf_release() does, and which results
in the same VM_BUG_ON_PAGE(PageLRU(page)) that the original patch was
trying to fix.
Reported-by: Justin Forbes <jmforbes@linuxtx.org>
Fixes: 712a951025 ("fuse: fix page stealing")
Cc: <stable@vger.kernel.org> # v2.6.35
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7fb0413baa upstream.
The HID descriptor of many of Wacom's touch input devices include a
"Confidence" usage that signals if a particular touch collection contains
useful data. The driver does not look at this flag, however, which causes
even invalid contacts to be reported to userspace. A lucky combination of
kernel event filtering and device behavior (specifically: contact ID 0 ==
invalid, contact ID >0 == valid; and order all data so that all valid
contacts are reported before any invalid contacts) spare most devices from
any visibly-bad behavior.
The DTH-2452 is one example of an unlucky device that misbehaves. It uses
ID 0 for both the first valid contact and all invalid contacts. Because
we report both the valid and invalid contacts, the kernel reports that
contact 0 first goes down (valid) and then goes up (invalid) in every
report. This causes ~100 clicks per second simply by touching the screen.
This patch inroduces new `confidence` flag in our `hid_data` structure.
The value is initially set to `true` at the start of a report and can be
set to `false` if an invalid touch usage is seen.
Link: https://github.com/linuxwacom/input-wacom/issues/270
Fixes: f8b6a74719 ("HID: wacom: generic: Support multiple tools per report")
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Tested-by: Joshua Dickens <joshua.dickens@wacom.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98400ad75e upstream.
This reverts commit 279917e27e.
With the CONFIG_HARDENED_USERCOPY option enabled, this patch triggers
kernel bugs at runtime:
usercopy: Kernel memory overwrite attempt detected to kernel text (offset 2084839, size 6)!
kernel BUG at mm/usercopy.c:99!
Backtrace:
IAOQ[0]: usercopy_abort+0xc4/0xe8
[<00000000406ed1c8>] __check_object_size+0x174/0x238
[<00000000407086d4>] copy_strings.isra.0+0x3e8/0x708
[<0000000040709a20>] do_execveat_common.isra.0+0x1bc/0x328
[<000000004070b760>] compat_sys_execve+0x7c/0xb8
[<0000000040303eb8>] syscall_exit+0x0/0x14
The problem is, that we have an init section of at least 2MB size which
starts at _stext and is freed after bootup.
If then later some kernel data is (temporarily) stored in this free
memory, check_kernel_text_object() will trigger a bug since the data
appears to be inside the kernel text (>=_stext) area:
if (overlaps(ptr, len, _stext, _etext))
usercopy_abort("kernel text");
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@kernel.org # 5.4+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13cbaa4c2b upstream.
When the reply for a non-blocking transmit arrives, the sequence
field for that reply was never filled in, so userspace would have no
way of associating the reply to the original transmit.
Copy the sequence field to ensure that this is now possible.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 0dbacebede ([media] cec: move the CEC framework out of staging and to media)
Cc: <stable@vger.kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 174a7fb385 upstream.
This applies a SND_PCI_QUIRK(...) to the ASRock NUC Box 1100 series. This
fixes the issue of the headphone jack not being detected unless warm
rebooted from a certain other OS.
When booting a certain other OS some coeff settings are changed that enable
the audio jack. These settings are preserved on a warm reboot and can be
easily dumped.
The relevant indexes and values where gathered by naively diff-ing and
reading a working and a non-working coeff dump.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211112110704.1022501-1-wse@tuxedocomputers.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 76c4718322 upstream.
The master and next_conj of rcs_ops are used for iterating the
resource list entries, and currently those are supposed to return the
current value. The problem is that next_conf may go over the last
entry before the loop abort condition is evaluated, and it may return
the "current" value that is beyond the array size. It was caught
recently as a GPF, for example.
Those return values are, however, never actually evaluated, hence
basically we don't have to consider the current value as the return at
all. By dropping those return values, the potential out-of-range
access above is also fixed automatically.
This patch changes the return type of master and next_conj callbacks
to void and drop the superfluous code accordingly.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214985
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211118215729.26257-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ae6dc22d2 upstream.
xHC hardware can only have one slot in default state with address 0
waiting for a unique address at a time, otherwise "undefined behavior
may occur" according to xhci spec 5.4.3.4
The address0_mutex exists to prevent this across both xhci roothubs.
If hub_port_init() fails, it may unlock the mutex and exit with a xhci
slot in default state. If the other xhci roothub calls hub_port_init()
at this point we end up with two slots in default state.
Make sure the address0_mutex protects the slot default state across
hub_port_init() retries, until slot is addressed or disabled.
Note, one known minor case is not fixed by this patch.
If device needs to be reset during resume, but fails all hub_port_init()
retries in usb_reset_and_verify_device(), then it's possible the slot is
still left in default state when address0_mutex is unlocked.
Cc: <stable@vger.kernel.org>
Fixes: 638139eb95 ("usb: hub: allow to process more usb hub events in parallel")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211115221630.871204-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 362468830d upstream.
The code that enables either BC_LVL or COMP_CHNG interrupt in tcpm_set_cc
wrongly assumes that the interrupt is unmasked by writing 1 to the apropriate
bit in the mask register. In fact, interrupts are enabled when the mask
is 0, so the tcpm_set_cc enables interrupt for COMP_CHNG when it expects
BC_LVL interrupt to be enabled.
This causes inability of the driver to recognize cable unplug events
in host mode (unplug is recognized only via a COMP_CHNG interrupt).
In device mode this bug was masked by simultaneous triggering of the VBUS
change interrupt, because of loss of VBUS when the port peer is providing
power.
Fixes: 48242e3053 ("usb: typec: fusb302: Revert "Resolve fixed power role contract setup"")
Cc: stable <stable@vger.kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Ondrej Jirman <megous@megous.com>
Link: https://lore.kernel.org/r/20211108102833.2793803-1-megous@megous.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63c4c320cc upstream.
The programming guide noted that the driver needs to verify if the link
state is in U0 before executing the Start Transfer command. If it's not
in U0, the driver needs to perform remote wakeup. This is not accurate.
If the link state is in U1/U2, then the controller will not respond to
link recovery request from DCTL.ULSTCHNGREQ. The Start Transfer command
will trigger a link recovery if it is in U1/U2. A clarification will be
added to the programming guide for all controller versions.
The current implementation shouldn't cause any functional issue. It may
occasionally report an invalid time out warning from failed link
recovery request. The driver will still go ahead with the Start Transfer
command if the remote wakeup fails. The new change only initiates remote
wakeup where it is needed, which is when the link state is in L1/L2/U3.
Fixes: c36d8e947a ("usb: dwc3: gadget: put link to U0 before Start Transfer")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/05b4a5fbfbd0863fc9b1d7af934a366219e3d0b4.1635204761.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 310780e825 upstream.
A new commit in LLVM causes an error on the use of 'long double' when
'-mno-x87' is used, which the kernel does through an alias,
'-mno-80387' (see the LLVM commit below for more details around why it
does this).
drivers/usb/dwc2/hcd_queue.c:1744:25: error: expression requires 'long double' type support, but target 'x86_64-unknown-linux-gnu' does not support it
delay = ktime_set(0, DWC2_RETRY_WAIT_DELAY);
^
drivers/usb/dwc2/hcd_queue.c:62:34: note: expanded from macro 'DWC2_RETRY_WAIT_DELAY'
#define DWC2_RETRY_WAIT_DELAY (1 * 1E6L)
^
1 error generated.
This happens due to the use of a 'long double' literal. The 'E6' part of
'1E6L' causes the literal to be a 'double' then the 'L' suffix promotes
it to 'long double'.
There is no visible reason for a floating point value in this driver, as
the value is only used as a parameter to a function that expects an
integer type. Use NSEC_PER_MSEC, which is the same integer value as
'1E6L', to avoid changing functionality but fix the error.
Link: https://github.com/ClangBuiltLinux/linux/issues/1497
Link: a8083d42b1
Fixes: 6ed30a7d8e ("usb: dwc2: host: use hrtimer for NAK retries")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: John Keeping <john@metanate.com>
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20211105145802.2520658-1-nathan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ad4a0b1d4 upstream.
Added updating of request frame number for elapsed frames,
otherwise frame number will remain as previous use of request.
This will allow function driver to correctly track frames in
case of Missed ISOC occurs.
Added setting request actual length to 0 for elapsed frames.
In Slave mode when pushing data to RxFIFO by dwords, request
actual length incrementing accordingly. But before whole packet
will be pushed into RxFIFO and send to host can occurs Missed
ISOC and data will not send to host. So, in this case request
actual length should be reset to 0.
Fixes: 91bb163e1e ("usb: dwc2: gadget: Fix ISOC flow for BDMA and Slave")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: John Keeping <john@metanate.com>
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/c356baade6e9716d312d43df08d53ae557cb8037.1636011277.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9054fc6d57 upstream.
Printk modifier %pfw is used to print the full path of the device name.
This is obtained device by device until a device no longer has a parent.
On ACPI getting the parent fwnode is done by calling acpi_get_parent()
which tries to down() a semaphore. But local IRQs are now disabled in
vprintk_store() before the mutex is acquired. This is obviously a problem.
Luckily struct device, embedded in struct acpi_device, has a parent field
already. Use that field to get the parent instead of relying on
acpi_get_parent().
Fixes: 3bd32d6a2e ("lib/vsprintf: Add %pfw conversion specifier for printing fwnode names")
Cc: 5.5+ <stable@vger.kernel.org> # 5.5+
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 353050be4c upstream.
Commit a23740ec43 ("bpf: Track contents of read-only maps as scalars") is
checking whether maps are read-only both from BPF program side and user space
side, and then, given their content is constant, reading out their data via
map->ops->map_direct_value_addr() which is then subsequently used as known
scalar value for the register, that is, it is marked as __mark_reg_known()
with the read value at verification time. Before a23740ec43, the register
content was marked as an unknown scalar so the verifier could not make any
assumptions about the map content.
The current implementation however is prone to a TOCTOU race, meaning, the
value read as known scalar for the register is not guaranteed to be exactly
the same at a later point when the program is executed, and as such, the
prior made assumptions of the verifier with regards to the program will be
invalid which can cause issues such as OOB access, etc.
While the BPF_F_RDONLY_PROG map flag is always fixed and required to be
specified at map creation time, the map->frozen property is initially set to
false for the map given the map value needs to be populated, e.g. for global
data sections. Once complete, the loader "freezes" the map from user space
such that no subsequent updates/deletes are possible anymore. For the rest
of the lifetime of the map, this freeze one-time trigger cannot be undone
anymore after a successful BPF_MAP_FREEZE cmd return. Meaning, any new BPF_*
cmd calls which would update/delete map entries will be rejected with -EPERM
since map_get_sys_perms() removes the FMODE_CAN_WRITE permission. This also
means that pending update/delete map entries must still complete before this
guarantee is given. This corner case is not an issue for loaders since they
create and prepare such program private map in successive steps.
However, a malicious user is able to trigger this TOCTOU race in two different
ways: i) via userfaultfd, and ii) via batched updates. For i) userfaultfd is
used to expand the competition interval, so that map_update_elem() can modify
the contents of the map after map_freeze() and bpf_prog_load() were executed.
This works, because userfaultfd halts the parallel thread which triggered a
map_update_elem() at the time where we copy key/value from the user buffer and
this already passed the FMODE_CAN_WRITE capability test given at that time the
map was not "frozen". Then, the main thread performs the map_freeze() and
bpf_prog_load(), and once that had completed successfully, the other thread
is woken up to complete the pending map_update_elem() which then changes the
map content. For ii) the idea of the batched update is similar, meaning, when
there are a large number of updates to be processed, it can increase the
competition interval between the two. It is therefore possible in practice to
modify the contents of the map after executing map_freeze() and bpf_prog_load().
One way to fix both i) and ii) at the same time is to expand the use of the
map's map->writecnt. The latter was introduced in fc9702273e ("bpf: Add mmap()
support for BPF_MAP_TYPE_ARRAY") and further refined in 1f6cb19be2 ("bpf:
Prevent re-mmap()'ing BPF map as writable for initially r/o mapping") with
the rationale to make a writable mmap()'ing of a map mutually exclusive with
read-only freezing. The counter indicates writable mmap() mappings and then
prevents/fails the freeze operation. Its semantics can be expanded beyond
just mmap() by generally indicating ongoing write phases. This would essentially
span any parallel regular and batched flavor of update/delete operation and
then also have map_freeze() fail with -EBUSY. For the check_mem_access() in
the verifier we expand upon the bpf_map_is_rdonly() check ensuring that all
last pending writes have completed via bpf_map_write_active() test. Once the
map->frozen is set and bpf_map_write_active() indicates a map->writecnt of 0
only then we are really guaranteed to use the map's data as known constants.
For map->frozen being set and pending writes in process of still being completed
we fall back to marking that register as unknown scalar so we don't end up
making assumptions about it. With this, both TOCTOU reproducers from i) and
ii) are fixed.
Note that the map->writecnt has been converted into a atomic64 in the fix in
order to avoid a double freeze_mutex mutex_{un,}lock() pair when updating
map->writecnt in the various map update/delete BPF_* cmd flavors. Spanning
the freeze_mutex over entire map update/delete operations in syscall side
would not be possible due to then causing everything to be serialized.
Similarly, something like synchronize_rcu() after setting map->frozen to wait
for update/deletes to complete is not possible either since it would also
have to span the user copy which can sleep. On the libbpf side, this won't
break d66562fba1 ("libbpf: Add BPF object skeleton support") as the
anonymous mmap()-ed "map initialization image" is remapped as a BPF map-backed
mmap()-ed memory where for .rodata it's non-writable.
Fixes: a23740ec43 ("bpf: Track contents of read-only maps as scalars")
Reported-by: w1tcher.bupt@gmail.com
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
[fix conflict to call bpf_map_write_active_dec() in err_put block.
fix conflict to insert new functions after find_and_alloc_map().]
Reference: CVE-2021-4001
Signed-off-by: Masami Ichikawa(CIP) <masami.ichikawa@cybertrust.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a dummy buffer is still active on a frame start, it indicates that this frame
will be dropped. The explicit logging helps users identify performance issues.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Deinterlace and decode aren't affected in the same way as encode
and ISP by the alignment requirement on 3 plane YUV420.
Decode would be affected, but it always aligns the height up to
a macroblock, and uses the selection API to reflect that.
Add in the facility to set the bytesperline alignment per role.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Remove min_buffers_needed=1 from src queue init. Src buffers are bound
to media requests therefore this setting is not needed and generates
a WARN in kernel 5.16.
Signed-off-by: John Cox <jc@kynesim.co.uk>
Matching https://github.com/raspberrypi/linux/pull/4419, the ISP
block (which is also used on the input of the encoder, and output
of the decoder) needs the base address of all planes to be aligned
to multiples of 32. This includes the chroma planes of YUV420 and
YVU420.
If the height is only a multiple of 2 (not 4), then you get an odd
number of lines in the second plane, which means the 3rd plane
starts at a multiple of bytesperline/2.
Set the minimum bytesperline alignment to 64 for those formats
so that the plane alignment is always right.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Avoid logging a spurious error message with error -517
(-EPROBE_DEFER) whilst trying to load HDMI audio.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Whilst investigations continue as to why the 7" DSI screen doesn't
work on Pi3 with KMS, drop the I2C baudrate to 50kHz as that seems
to be a reliable workaround.
This will be reverted once the full issue is understood.
https://github.com/raspberrypi/linux/issues/4686
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Whilst all the datasheets describe FT5x06 as supporting "up to
10 points of absolution X and Y coordinates", the driver
implementation for the compatible string "edt,edt-ft5x06" only
allows for 5.
Switch to the "edt,edt-ft5506" compatible string which allows for
10 points with no other differences.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The ft5x06 is unreliable in sending touch up events, so some
touch IDs can become stuck in the detected state.
Ensure that IDs that are unreported by the controller are
released.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The Pi 4B dts file has had numerous updates since the Pi 400 and CM4
dts files were written. Apply those updates to the other files to
minimise the differences. The change is largely cosmetic, except for
the PCI "device-type" to "device_type" rename, and the correction of
the labels on the Pi 400 GPIO expander pins.
Also set the wifi-2.4ghz-coexistence property on RPi 4 B, which appears
to have been missed.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The existing logic was flawed in that it could try reading the
2711 specific registers for HPD on a CM1/3 where the HPD GPIO
hadn't been defined in DT.
Ensure we don't do the 2711 register read on invalid hardware,
and then
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The hardware can combine H&V syncs onto the output enable line
as composite syncs, so add the relevant configuration to do that.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
This reverts commit 94902ee299 which is
upstream commit ef54c1a476.
Reverting for now due to issues that need to get fixed upstream.
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 868ddfcef3 upstream.
The code for hdac_ext_stream seems inherited from hdac_stream, and
similar locking issues are present: the use of the bus->reg_lock
spinlock is inconsistent, with only writes to specific fields being
protected.
Apply similar fix as in hdac_stream by protecting all accesses to
'link_locked' and 'decoupled' fields, with a new helper
snd_hdac_ext_stream_decouple_locked() added to simplify code
changes.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210924192417.169243-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef775a0e36 upstream.
When CONFIG_PROC_FS is not set, there is a build warning (turned
into an error):
../drivers/hwmon/dell-smm-hwmon.c: In function 'i8k_init_procfs':
../drivers/hwmon/dell-smm-hwmon.c:624:24: error: unused variable 'data' [-Werror=unused-variable]
struct dell_smm_data *data = dev_get_drvdata(dev);
Make I8K depend on PROC_FS and HWMON (instead of selecting HWMON -- it
is strongly preferred to not select entire subsystems).
Build tested in all possible combinations of SENSORS_DELL_SMM, I8K, and
PROC_FS.
Fixes: 039ae58503 ("hwmon: Allow to compile dell-smm-hwmon driver without /proc/i8k")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Pali Rohár <pali@kernel.org>
Link: https://lkml.kernel.org/r/20210910071921.16777-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54fde91f52 upstream.
Christoph pointed out that I'm updating bdev->bd_inode for the device
time when we remove block devices from a btrfs file system, however this
isn't actually exposed to anything. The inode we want to update is the
one that's associated with the path to the device, usually on devtmpfs,
so that blkid notices the difference.
We still don't want to do the blkdev_open, so use kern_path() to get the
path to the given device and do the update time on that inode.
Fixes: 8f96a5bfa1 ("btrfs: update the bdev time directly when closing")
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e60feb445f upstream.
If you already have an inode and need to update the time on the inode
there is no way to do this properly. Export this helper to allow file
systems to update time on the inode so the appropriate handler is
called, either ->update_time or generic_update_time.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2ff04286a9 upstream.
PF pointer is always valid when PCI core calls its .shutdown() and
.remove() callbacks. There is no need to check it again.
Fixes: 837f08fdec ("ice: Add basic driver framework for Intel(R) E800 Series")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc153aba3e upstream.
Instead of maintaining a single-linked list of devices that must be
searched linearly in .remove() just use spi_set_drvdata() to remember the
link between the spi device and the driver struct. Then the global list
and the next member can be dropped.
This simplifies the driver, reduces the memory footprint and the time to
search the list. Also it makes obvious that there is always a corresponding
driver struct for a given device in .remove(), so the error path for
!max3421_hcd can be dropped, too.
As a side effect this fixes a data inconsistency when .probe() races with
itself for a second max3421 device in manipulating max3421_hcd_list. A
similar race is fixed in .remove(), too.
Fixes: 2d53139f31 ("Add support for using a MAX3421E chip as a host driver.")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211018204028.2914597-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 827b0913a9 upstream.
The recent fix for DAPM to correct the kctl change notification by the
commit 5af82c81b2 ("ASoC: DAPM: Fix missing kctl change
notifications") caused other regressions since it changed the behavior
of snd_soc_dapm_set_pin() that is called from several API functions.
Formerly it returned always 0 for success, but now it returns 0 or 1.
This patch addresses it, restoring the old behavior of
snd_soc_dapm_set_pin() while keeping the fix in
snd_soc_dapm_put_pin_switch().
Fixes: 5af82c81b2 ("ASoC: DAPM: Fix missing kctl change notifications")
Reported-by: Yu-Hsuan Hsu <yuhsuan@chromium.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20211105090925.20575-1-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc27f3c5d1 upstream.
When the hash table slot array allocation fails in hashtab_init(),
h->size is left initialized with a non-zero value, but the h->htable
pointer is NULL. This may then cause a NULL pointer dereference, since
the policydb code relies on the assumption that even after a failed
hashtab_init(), hashtab_map() and hashtab_destroy() can be safely called
on it. Yet, these detect an empty hashtab only by looking at the size.
Fix this by making sure that hashtab_init() always leaves behind a valid
empty hashtab when the allocation fails.
Cc: stable@vger.kernel.org
Fixes: 03414a49ad ("selinux: do not allocate hashtabs dynamically")
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4a118f2ee upstream.
When __unmap_hugepage_range() calls to huge_pmd_unshare() succeed, a TLB
flush is missing. This TLB flush must be performed before releasing the
i_mmap_rwsem, in order to prevent an unshared PMDs page from being
released and reused before the TLB flush took place.
Arguably, a comprehensive solution would use mmu_gather interface to
batch the TLB flushes and the PMDs page release, however it is not an
easy solution: (1) try_to_unmap_one() and try_to_migrate_one() also call
huge_pmd_unshare() and they cannot use the mmu_gather interface; and (2)
deferring the release of the page reference for the PMDs page until
after i_mmap_rwsem is dropeed can confuse huge_pmd_unshare() into
thinking PMDs are shared when they are not.
Fix __unmap_hugepage_range() by adding the missing TLB flush, and
forcing a flush when unshare is successful.
Fixes: 24669e5847 ("hugetlb: use mmu_gather instead of a temporary linked list for accumulating pages)" # 3.6
Signed-off-by: Nadav Amit <namit@vmware.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 886fe2915c upstream.
__ufshcd_issue_tm_cmd() clears req->end_io_data after timing out, which
races with the completion function ufshcd_tmc_handler() which expects
req->end_io_data to have a value.
Note __ufshcd_issue_tm_cmd() and ufshcd_tmc_handler() are already
synchronized using hba->tmf_rqs and hba->outstanding_tasks under the
host_lock spinlock.
It is also not necessary (nor typical) to clear req->end_io_data because
the block layer does it before allocating out requests e.g. via
blk_get_request().
So fix by not clearing it.
Link: https://lore.kernel.org/r/20211108064815.569494-2-adrian.hunter@intel.com
Fixes: f5ef336fd2 ("scsi: ufs: core: Fix task management completion")
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[Adrian: Backport to v5.10]
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f5ef336fd2 upstream.
The UFS driver uses blk_mq_tagset_busy_iter() when identifying task
management requests to complete, however blk_mq_tagset_busy_iter() doesn't
work.
blk_mq_tagset_busy_iter() only iterates requests dispatched by the block
layer. That appears as if it might have started since commit 37f4a24c24
("blk-mq: centralise related handling into blk_mq_get_driver_tag") which
removed 'data->hctx->tags->rqs[rq->tag] = rq' from blk_mq_rq_ctx_init()
which gets called:
blk_get_request
blk_mq_alloc_request
__blk_mq_alloc_request
blk_mq_rq_ctx_init
Since UFS task management requests are not dispatched by the block layer,
hctx->tags->rqs[rq->tag] remains NULL, and since blk_mq_tagset_busy_iter()
relies on finding requests using hctx->tags->rqs[rq->tag], UFS task
management requests are never found by blk_mq_tagset_busy_iter().
By using blk_mq_tagset_busy_iter(), the UFS driver was relying on internal
details of the block layer, which was fragile and subsequently got
broken. Fix by removing the use of blk_mq_tagset_busy_iter() and having the
driver keep track of task management requests.
Link: https://lore.kernel.org/r/20210922091059.4040-1-adrian.hunter@intel.com
Fixes: 1235fc569e ("scsi: ufs: core: Fix task management request completion timeout")
Fixes: 69a6c269c0 ("scsi: ufs: Use blk_{get,put}_request() to allocate and free TMFs")
Cc: stable@vger.kernel.org
Tested-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[Adrian: Backport to v5.10]
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf55208391 upstream.
amdgpu_connector_vga_get_modes missed function amdgpu_get_native_mode
which assign amdgpu_encoder->native_mode with *preferred_mode result in
amdgpu_encoder->native_mode.clock always be 0. That will cause
amdgpu_connector_set_property returned early on:
if ((rmx_type != DRM_MODE_SCALE_NONE) &&
(amdgpu_encoder->native_mode.clock == 0))
when we try to set scaling mode Full/Full aspect/Center.
Add the missing function to amdgpu_connector_vga_get_mode can fix this.
It also works on dvi connectors because
amdgpu_connector_dvi_helper_funcs.get_mode use the same method.
Signed-off-by: hongao <hongao@uniontech.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c34bd4532 upstream.
Atm, there are no sink rate values set for DP (vs. eDP) sinks until the
DPCD capabilities are successfully read from the sink. During this time
intel_dp->num_common_rates is 0 which can lead to a
intel_dp->common_rates[-1] (*)
access, which is an undefined behaviour, in the following cases:
- In intel_dp_sync_state(), if the encoder is enabled without a sink
connected to the encoder's connector (BIOS enabled a monitor, but the
user unplugged the monitor until the driver loaded).
- In intel_dp_sync_state() if the encoder is enabled with a sink
connected, but for some reason the DPCD read has failed.
- In intel_dp_compute_link_config() if modesetting a connector without
a sink connected on it.
- In intel_dp_compute_link_config() if modesetting a connector with a
a sink connected on it, but before probing the connector first.
To avoid the (*) access in all the above cases, make sure that the sink
rate table - and hence the common rate table - is always valid, by
setting a default minimum sink rate when registering the connector
before anything could use it.
I also considered setting all the DP link rates by default, so that
modesetting with higher resolution modes also succeeds in the last two
cases above. However in case a sink is not connected that would stop
working after the first modeset, due to the LT fallback logic. So this
would need more work, beyond the scope of this fix.
As I mentioned in the previous patch, I don't think the issue this patch
fixes is user visible, however it is an undefined behaviour by
definition and triggers a BUG() in CONFIG_UBSAN builds, hence CC:stable.
v2: Clear the default sink rates, before initializing these for eDP.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/4297
References: https://gitlab.freedesktop.org/drm/intel/-/issues/4298
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211018143417.1452632-1-imre.deak@intel.com
(cherry picked from commit 3f61ef9777)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f55aaf63bd upstream.
The postclose handler can run after the device has been removed (or the
driver has been unbound) since userspace clients are free to hold the
file open as long as they want. Because the device removal callback
frees the entire nouveau_drm structure, any reference to it in the
postclose handler will result in a use-after-free.
To reproduce this, one must simply open the device file, unbind the
driver (or physically remove the device), and then close the device
file. This was found and can be reproduced easily with the IGT
core_hotunplug tests.
To avoid this, all clients are cleaned up in the device finalization
rather than deferring it to the postclose handler, and the postclose
handler is protected by a critical section which ensures the
drm_dev_unplug() and the postclose handler won't race.
This is not an ideal fix, since as I understand the proposed plan for
the kernel<->userspace interface for hotplug support, destroying the
client before the file is closed will cause problems. However, I believe
to properly fix this issue, the lifetime of the nouveau_drm structure
needs to be extended to match the drm_device, and this proved to be a
rather invasive change. Thus, I've broken this out so the fix can be
easily backported.
This fixes with the two previous commits CVE-2020-27820 (Karol).
Cc: stable@vger.kernel.org # 5.4+
Signed-off-by: Jeremy Cline <jcline@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Ben Skeggs <bskeggs@redhat.com>
Tested-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201125202648.5220-4-jcline@redhat.com
Link: https://gitlab.freedesktop.org/drm/nouveau/-/merge_requests/14
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bec05f33eb upstream.
sticon_build_attr() checked the reverse argument and flipped
background and foreground color, but returned the non-reverse
value afterwards. Fix this and also add two local variables
for foreground and background color to make the code easier
to read.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45da9c1767 upstream.
Ordered work functions aren't guaranteed to be handled by the same thread
which executed the normal work functions. The only way execution between
normal/ordered functions is synchronized is via the WORK_DONE_BIT,
unfortunately the used bitops don't guarantee any ordering whatsoever.
This manifested as seemingly inexplicable crashes on ARM64, where
async_chunk::inode is seen as non-null in async_cow_submit which causes
submit_compressed_extents to be called and crash occurs because
async_chunk::inode suddenly became NULL. The call trace was similar to:
pc : submit_compressed_extents+0x38/0x3d0
lr : async_cow_submit+0x50/0xd0
sp : ffff800015d4bc20
<registers omitted for brevity>
Call trace:
submit_compressed_extents+0x38/0x3d0
async_cow_submit+0x50/0xd0
run_ordered_work+0xc8/0x280
btrfs_work_helper+0x98/0x250
process_one_work+0x1f0/0x4ac
worker_thread+0x188/0x504
kthread+0x110/0x114
ret_from_fork+0x10/0x18
Fix this by adding respective barrier calls which ensure that all
accesses preceding setting of WORK_DONE_BIT are strictly ordered before
setting the flag. At the same time add a read barrier after reading of
WORK_DONE_BIT in run_ordered_work which ensures all subsequent loads
would be strictly ordered after reading the bit. This in turn ensures
are all accesses before WORK_DONE_BIT are going to be strictly ordered
before any access that can occur in ordered_func.
Reported-by: Chris Murphy <lists@colorremedies.com>
Fixes: 08a9ff3264 ("btrfs: Added btrfs_workqueue_struct implemented ordered execution based on kernel workqueue")
CC: stable@vger.kernel.org # 4.4+
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2011928
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Tested-by: Chris Murphy <chris@colorremedies.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9119570039 upstream.
According to upstream commit 5ec55823438e("net: stmmac:
add clocks management for gmac driver"), it improve clocks
management for stmmac driver. So, it is necessary to implement
the runtime callback in dwmac-socfpga driver because it doesn't
use the common stmmac_pltfr_pm_ops instance. Otherwise, clocks
are not disabled when system enters suspend status.
Fixes: 5ec5582343 ("net: stmmac: add clocks management for gmac driver")
Cc: stable@vger.kernel.org
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a48fc69fe6 upstream.
udf_readdir() didn't validate the directory position it should start
reading from. Thus when user uses lseek(2) on directory file descriptor
it can trick udf_readdir() into reading from a position in the middle of
directory entry which then upsets directory parsing code resulting in
errors or even possible kernel crashes. Similarly when the directory is
modified between two readdir calls, the directory position need not be
valid anymore.
Add code to validate current offset in the directory. This is actually
rather expensive for UDF as we need to read from the beginning of the
directory and parse all directory entries. This is because in UDF a
directory is just a stream of data containing directory entries and
since file names are fully under user's control we cannot depend on
detecting magic numbers and checksums in the header of directory entry
as a malicious attacker could fake them. We skip this step if we detect
that nothing changed since the last readdir call.
Reported-by: Nathan Wilson <nate@chickenbrittle.com>
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af957eebfc upstream.
When loading nested state, don't use check vcpu->arch.efer to get the
L1 host's 64-bit vs. 32-bit state and don't check it for consistency
with respect to VM_EXIT_HOST_ADDR_SPACE_SIZE, as register state in vCPU
may be stale when KVM_SET_NESTED_STATE is called---and architecturally
does not exist. When restoring L2 state in KVM, the CPU is placed in
non-root where nested VMX code has no snapshot of L1 host state: VMX
(conditionally) loads host state fields loaded on VM-exit, but they need
not correspond to the state before entry. A simple case occurs in KVM
itself, where the host RIP field points to vmx_vmexit rather than the
instruction following vmlaunch/vmresume.
However, for the particular case of L1 being in 32- or 64-bit mode
on entry, the exit controls can be treated instead as the source of
truth regarding the state of L1 on entry, and can be used to check
that vmcs12.VM_EXIT_HOST_ADDR_SPACE_SIZE matches vmcs12.HOST_EFER if
vmcs12.VM_EXIT_LOAD_IA32_EFER is set. The consistency check on CPU
EFER vs. vmcs12.VM_EXIT_HOST_ADDR_SPACE_SIZE, instead, happens only
on VM-Enter. That's because, again, there's conceptually no "current"
L1 EFER to check on KVM_SET_NESTED_STATE.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20211115131837.195527-2-mlevitsk@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e35eba405 upstream.
As spotted and explained in commit c12ab8dbc4 ("powerpc/8xx: Fix
Oops with STRICT_KERNEL_RWX without DEBUG_RODATA_TEST"), the selection
of STRICT_KERNEL_RWX without selecting DEBUG_RODATA_TEST has spotted
the lack of the DIRTY bit in the pinned kernel data TLBs.
This problem should have been detected a lot earlier if things had
been working as expected. But due to an incredible level of chance or
mishap, this went undetected because of a set of bugs: In fact the
DTLBs were not pinned, because instead of setting the reserve bit
in MD_CTR, it was set in MI_CTR that is the register for ITLBs.
But then, another huge bug was there: the physical address was
reset to 0 at the boundary between RO and RW areas, leading to the
same physical space being mapped at both 0xc0000000 and 0xc8000000.
This had by miracle no consequence until now because the entry was
not really pinned so it was overwritten soon enough to go undetected.
Of course, now that we really pin the DTLBs, it must be fixed as well.
Fixes: f76c8f6d25 ("powerpc/8xx: Add function to set pinned TLBs")
Cc: stable@vger.kernel.org # v5.8+
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Depends-on: c12ab8dbc4 ("powerpc/8xx: Fix Oops with STRICT_KERNEL_RWX without DEBUG_RODATA_TEST")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/a21e9a057fe2d247a535aff0d157a54eefee017a.1636963688.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 126e8bee94 upstream.
Patch series "shm: shm_rmid_forced feature fixes".
Some time ago I met kernel crash after CRIU restore procedure,
fortunately, it was CRIU restore, so, I had dump files and could do
restore many times and crash reproduced easily. After some
investigation I've constructed the minimal reproducer. It was found
that it's use-after-free and it happens only if sysctl
kernel.shm_rmid_forced = 1.
The key of the problem is that the exit_shm() function not handles shp's
object destroy when task->sysvshm.shm_clist contains items from
different IPC namespaces. In most cases this list will contain only
items from one IPC namespace.
How can this list contain object from different namespaces? The
exit_shm() function is designed to clean up this list always when
process leaves IPC namespace. But we made a mistake a long time ago and
did not add a exit_shm() call into the setns() syscall procedures.
The first idea was just to add this call to setns() syscall but it
obviously changes semantics of setns() syscall and that's
userspace-visible change. So, I gave up on this idea.
The first real attempt to address the issue was just to omit forced
destroy if we meet shp object not from current task IPC namespace [1].
But that was not the best idea because task->sysvshm.shm_clist was
protected by rwsem which belongs to current task IPC namespace. It
means that list corruption may occur.
Second approach is just extend exit_shm() to properly handle shp's from
different IPC namespaces [2]. This is really non-trivial thing, I've
put a lot of effort into that but not believed that it's possible to
make it fully safe, clean and clear.
Thanks to the efforts of Manfred Spraul working an elegant solution was
designed. Thanks a lot, Manfred!
Eric also suggested the way to address the issue in ("[RFC][PATCH] shm:
In shm_exit destroy all created and never attached segments") Eric's
idea was to maintain a list of shm_clists one per IPC namespace, use
lock-less lists. But there is some extra memory consumption-related
concerns.
An alternative solution which was suggested by me was implemented in
("shm: reset shm_clist on setns but omit forced shm destroy"). The idea
is pretty simple, we add exit_shm() syscall to setns() but DO NOT
destroy shm segments even if sysctl kernel.shm_rmid_forced = 1, we just
clean up the task->sysvshm.shm_clist list.
This chages semantics of setns() syscall a little bit but in comparision
to the "naive" solution when we just add exit_shm() without any special
exclusions this looks like a safer option.
[1] https://lkml.org/lkml/2021/7/6/1108
[2] https://lkml.org/lkml/2021/7/14/736
This patch (of 2):
Let's produce a warning if we trying to remove non-existing IPC object
from IPC namespace kht/idr structures.
This allows us to catch possible bugs when the ipc_rmid() function was
called with inconsistent struct ipc_ids*, struct kern_ipc_perm*
arguments.
Link: https://lkml.kernel.org/r/20211027224348.611025-1-alexander.mikhalitsyn@virtuozzo.com
Link: https://lkml.kernel.org/r/20211027224348.611025-2-alexander.mikhalitsyn@virtuozzo.com
Co-developed-by: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Alexander Mikhalitsyn <alexander.mikhalitsyn@virtuozzo.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Andrei Vagin <avagin@gmail.com>
Cc: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Cc: Vasily Averin <vvs@virtuozzo.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51f2ec5934 upstream.
When building allmodconfig, there is a warning about TIMER_ENABLE being
redefined:
drivers/clocksource/timer-oxnas-rps.c:39:9: error: 'TIMER_ENABLE' macro redefined [-Werror,-Wmacro-redefined]
#define TIMER_ENABLE BIT(7)
^
arch/hexagon/include/asm/timer-regs.h:13:9: note: previous definition is here
#define TIMER_ENABLE 0
^
1 error generated.
The values in this header are only used in one file each, if they are
used at all. Remove the header and sink all of the constants into their
respective files.
TCX0_CLK_RATE is only used in arch/hexagon/include/asm/timex.h
TIMER_ENABLE, RTOS_TIMER_INT, RTOS_TIMER_REGS_ADDR are only used in
arch/hexagon/kernel/time.c.
SLEEP_CLK_RATE and TIMER_CLR_ON_MATCH have both been unused since the
file's introduction in commit 71e4a47f32 ("Hexagon: Add time and timer
functions").
TIMER_ENABLE is redefined as BIT(0) so the shift is moved into the
definition, rather than its use.
Link: https://lkml.kernel.org/r/20211115174250.1994179-3-nathan@kernel.org
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Brian Cain <bcain@codeaurora.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ffb92ce826 upstream.
Patch series "Fixes for ARCH=hexagon allmodconfig", v2.
This series fixes some issues noticed with ARCH=hexagon allmodconfig.
This patch (of 3):
When building ARCH=hexagon allmodconfig, the following errors occur:
ERROR: modpost: "__raw_readsl" [drivers/i3c/master/svc-i3c-master.ko] undefined!
ERROR: modpost: "__raw_writesl" [drivers/i3c/master/dw-i3c-master.ko] undefined!
ERROR: modpost: "__raw_readsl" [drivers/i3c/master/dw-i3c-master.ko] undefined!
ERROR: modpost: "__raw_writesl" [drivers/i3c/master/i3c-master-cdns.ko] undefined!
ERROR: modpost: "__raw_readsl" [drivers/i3c/master/i3c-master-cdns.ko] undefined!
Export these symbols so that modules can use them without any errors.
Link: https://lkml.kernel.org/r/20211115174250.1994179-1-nathan@kernel.org
Link: https://lkml.kernel.org/r/20211115174250.1994179-2-nathan@kernel.org
Fixes: 013bf24c38 ("Hexagon: Provide basic implementation and/or stubs for I/O routines.")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Brian Cain <bcain@codeaurora.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14831fad73 upstream.
When running the following command without arm-linux-gnueabi-gcc in
one's $PATH, the following warning is observed:
$ ARCH=arm64 CROSS_COMPILE_COMPAT=arm-linux-gnueabi- make -j72 LLVM=1 mrproper
make[1]: arm-linux-gnueabi-gcc: No such file or directory
This is because KCONFIG is not run for mrproper, so CONFIG_CC_IS_CLANG
is not set, and we end up eagerly evaluating various variables that try
to invoke CC_COMPAT.
This is a similar problem to what was observed in
commit dc960bfeed ("h8300: suppress error messages for 'make clean'")
Reported-by: Lucas Henneman <henneman@google.com>
Suggested-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20211019223646.1146945-4-ndesaulniers@google.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aec3f415f7 upstream.
Commit 2d26f6e39a ("net: stmmac: dwmac-rk: fix unbalanced pm_runtime_enable warnings")
while getting rid of a runtime PM warning ended up breaking ethernet
on rk3399 based devices. By dropping an extra reference to the device,
the commit ends up enabling suspend / resume of the ethernet device -
which appears to be broken.
While the issue with runtime pm is being investigated, partially
revert commit 2d26f6e39a to restore the network on rk3399.
Fixes: 2d26f6e39a ("net: stmmac: dwmac-rk: fix unbalanced pm_runtime_enable warnings")
Suggested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Punit Agrawal <punitagrawal@gmail.com>
Cc: Michael Riesch <michael.riesch@wolfvision.net>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20210929135049.3426058-1-punitagrawal@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 20c76e242e ]
kexec_file_add_ipl_report ignores that ipl_report_finish may fail and
can return an error pointer instead of a valid pointer.
Fix this and simplify by returning NULL in case of an error and let
the only caller handle this case.
Fixes: 99feaa717e ("s390/kexec_file: Create ipl report and pass to next kernel")
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a3a100473 ]
It has been observed that dual edge triggered wakeirq GPIOs on SDM845
doesn't trigger interrupts on the falling edge.
Enabling wakeirq_dual_edge_errata for SDM845 indicates that the PDC in
SDM845 suffers from the same problem described, and worked around, by
Doug in 'c3c0c2e18d94 ("pinctrl: qcom: Handle broken/missing PDC dual
edge IRQs on sc7180")', so enable the workaround for SDM845 as well.
The specific problem seen without this is that gpio-keys does not detect
the falling edge of the LID gpio on the Lenovo Yoga C630 and as such
consistently reports the LID as closed.
Fixes: e35a6ae0eb ("pinctrl/msm: Setup GPIO chip in hierarchy")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-By: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20211102034115.1946036-1-bjorn.andersson@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dae5818646 ]
kvmppc_h_set_dabr(), and kvmppc_h_set_xdabr() which jumps into
it, need to use _GLOBAL_TOC to setup the kernel TOC pointer, because
kvmppc_h_set_dabr() uses LOAD_REG_ADDR() to load dawr_force_enable.
When called from hcall_try_real_mode() we have the kernel TOC in r2,
established near the start of kvmppc_interrupt_hv(), so there is no
issue.
But they can also be called from kvmppc_pseries_do_hcall() which is
module code, so the access ends up happening with the kvm-hv module's
r2, which will not point at dawr_force_enable and could even cause a
fault.
With the current code layout and compilers we haven't observed a fault
in practice, the load hits somewhere in kvm-hv.ko and silently returns
some bogus value.
Note that we we expect p8/p9 guests to use the DAWR, but SLOF uses
h_set_dabr() to test if sc1 works correctly, see SLOF's
lib/libhvcall/brokensc1.c.
Fixes: c1fe190c06 ("powerpc: Add force enable of DAWR on P9 option")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Link: https://lore.kernel.org/r/20210923151031.72408-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d2ca2e12d ]
As reported in [1], e100 was no longer working for suspend/resume
cycles. The previous commit mentioned in the fixes appears to have
broken things and this attempts to practice best known methods for
device power management and keep wake-up working while allowing
suspend/resume to work. To do this, I reorder a little bit of code
and fix the resume path to make sure the device is enabled.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=214933
Fixes: 69a74aef8a ("e100: use generic power management")
Cc: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Reported-by: Alexey Kuznetsov <axet@me.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Alexey Kuznetsov <axet@me.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48b71a9e66 ]
There are two sites that calls queue_work() after the
destroy_workqueue() and lead to possible UAF.
The first site is nci_send_cmd(), which can happen after the
nci_close_device as below
nfcmrvl_nci_unregister_dev | nfc_genl_dev_up
nci_close_device |
flush_workqueue |
del_timer_sync |
nci_unregister_device | nfc_get_device
destroy_workqueue | nfc_dev_up
nfc_unregister_device | nci_dev_up
device_del | nci_open_device
| __nci_request
| nci_send_cmd
| queue_work !!!
Another site is nci_cmd_timer, awaked by the nci_cmd_work from the
nci_send_cmd.
... | ...
nci_unregister_device | queue_work
destroy_workqueue |
nfc_unregister_device | ...
device_del | nci_cmd_work
| mod_timer
| ...
| nci_cmd_timer
| queue_work !!!
For the above two UAF, the root cause is that the nfc_dev_up can race
between the nci_unregister_device routine. Therefore, this patch
introduce NCI_UNREG flag to easily eliminate the possible race. In
addition, the mutex_lock in nci_close_device can act as a barrier.
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Fixes: 6a2968aaf5 ("NFC: basic NCI protocol implementation")
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211116152732.19238-1-linma@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f011539e72 ]
If there is a NCI command in work queue after closing the NCI device at
nci_unregister_device, The NCI command timer starts at flush_workqueue
function and then NCI command timeout handler would be called 5 second
after flushing the NCI command work queue and destroying the queue.
At that time, the timeout handler would try to use NCI command work queue
that is destroyed already. it will causes the problem. To avoid this
abnormal situation, change the sequence to prevent the NCI command timeout
handler from being called after destroying the NCI command work queue.
Signed-off-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e3b5dfcd1 ]
There is a potential UAF between the unregistration routine and the NFC
netlink operations.
The race that cause that UAF can be shown as below:
(FREE) | (USE)
nfcmrvl_nci_unregister_dev | nfc_genl_dev_up
nci_close_device |
nci_unregister_device | nfc_get_device
nfc_unregister_device | nfc_dev_up
rfkill_destory |
device_del | rfkill_blocked
... | ...
The root cause for this race is concluded below:
1. The rfkill_blocked (USE) in nfc_dev_up is supposed to be placed after
the device_is_registered check.
2. Since the netlink operations are possible just after the device_add
in nfc_register_device, the nfc_dev_up() can happen anywhere during the
rfkill creation process, which leads to data race.
This patch reorder these actions to permit
1. Once device_del is finished, the nfc_dev_up cannot dereference the
rfkill object.
2. The rfkill_register need to be placed after the device_add of nfc_dev
because the parent device need to be created first. So this patch keeps
the order but inject device_lock to prevent the data race.
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Fixes: be055b2f89 ("NFC: RFKILL support")
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211116152652.19217-1-linma@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86cdf8e387 ]
There is a possible data race as shown below:
thread-A in nci_request() | thread-B in nci_close_device()
| mutex_lock(&ndev->req_lock);
test_bit(NCI_UP, &ndev->flags); |
... | test_and_clear_bit(NCI_UP, &ndev->flags)
mutex_lock(&ndev->req_lock); |
|
This race will allow __nci_request() to be awaked while the device is
getting removed.
Similar to commit e2cb6b891a ("bluetooth: eliminate the potential race
condition when removing the HCI controller"). this patch alters the
function sequence in nci_request() to prevent the data races between the
nci_close_device().
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Fixes: 6a2968aaf5 ("NFC: basic NCI protocol implementation")
Link: https://lore.kernel.org/r/20211115145600.8320-1-linma@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5aff430d4e ]
Fix misleading display error in dmesg if tc filter return fail.
Only i40e status error code should be converted to string, not linux
error code. Otherwise, we return false information about the error.
Fixes: 2f4b411a3d ("i40e: Enable cloud filters via tc-flower")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e6d218c1e ]
Reject TCs creation with proper message if the first queue
assignment is not equal to the power of two.
The first queue number was checked too late in the second queue
iteration, if second queue was configured at all. Now if first queue value
is not a power of two, then trying to create qdisc will be rejected.
Fixes: 8f88b3034d ("i40e: Add infrastructure for queue channel support")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a3b311e38 ]
Restore part of reset functionality used when reset is called
from the VF to reset itself. Without this fix warning message
is displayed when VF is being removed via sysfs.
Fix the crash of the VF during reset by ensuring
that the PF receives the reset message successfully.
Refactor code to use one function instead of two.
Fixes: 5c3c48ac6b ("i40e: implement virtual device interface")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e0a603cb7 ]
Properly reconfigure VF VSIs after VF request ADQ.
Created new function to update queue mapping and queue pairs per TC
with AQ update VSI. This sets proper RSS size on NIC.
VFs num_queue_pairs should not be changed during setup of queue maps.
Previously, VF main VSI in ADQ had configured too many queues and had
wrong RSS size, which lead to packets not being consumed and drops in
connectivity.
Fixes: bc6d33c8d9 ("i40e: Fix the number of queues available to be mapped for use")
Co-developed-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Eryk Rybak <eryk.roch.rybak@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d2a69fefd7 ]
Currently, the i40e_vsi_setup_queue_map is basing the count of queues in
TCs on a VSI's alloc_queue_pairs member which is not changed throughout
any user's action (for example via ethtool's set_channels callback).
This implies that vsi->tc_config.tc_info[n].qcount value that is given
to the kernel via netdev_set_tc_queue() that notifies about the count of
queues per particular traffic class is constant even if user has changed
the total count of queues.
This in turn caused the kernel warning after setting the queue count to
the lower value than the initial one:
$ ethtool -l ens801f0
Channel parameters for ens801f0:
Pre-set maximums:
RX: 0
TX: 0
Other: 1
Combined: 64
Current hardware settings:
RX: 0
TX: 0
Other: 1
Combined: 64
$ ethtool -L ens801f0 combined 40
[dmesg]
Number of in use tx queues changed invalidating tc mappings. Priority
traffic classification disabled!
Reason was that vsi->alloc_queue_pairs stayed at 64 value which was used
to set the qcount on TC0 (by default only TC0 exists so all of the
existing queues are assigned to TC0). we update the offset/qcount via
netdev_set_tc_queue() back to the old value but then the
netif_set_real_num_tx_queues() is using the vsi->num_queue_pairs as a
value which got set to 40.
Fix it by using vsi->req_queue_pairs as a queue count that will be
distributed across TCs. Do it only for non-zero values, which implies
that user actually requested the new count of queues.
For VSIs other than main, stay with the vsi->alloc_queue_pairs as we
only allow manipulating the queue count on main VSI.
Fixes: bc6d33c8d9 ("i40e: Fix the number of queues available to be mapped for use")
Co-developed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Co-developed-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Eryk Rybak <eryk.roch.rybak@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf9acc90c8 ]
virtio_net_hdr_to_skb does not set the skb's gso_size and gso_type
correctly for UFO packets received via virtio-net that are a little over
the GSO size. This can lead to problems elsewhere in the networking
stack, e.g. ovs_vport_send dropping over-sized packets if gso_size is
not set.
This is due to the comparison
if (skb->len - p_off > gso_size)
not properly accounting for the transport layer header.
p_off includes the size of the transport layer header (thlen), so
skb->len - p_off is the size of the TCP/UDP payload.
gso_size is read from the virtio-net header. For UFO, fragmentation
happens at the IP level so does not need to include the UDP header.
Hence the calculation could be comparing a TCP/UDP payload length with
an IP payload length, causing legitimate virtio-net packets to have
lack gso_type/gso_size information.
Example: a UDP packet with payload size 1473 has IP payload size 1481.
If the guest used UFO, it is not fragmented and the virtio-net header's
flags indicate that it is a GSO frame (VIRTIO_NET_HDR_GSO_UDP), with
gso_size = 1480 for an MTU of 1500. skb->len will be 1515 and p_off
will be 42, so skb->len - p_off = 1473. Hence the comparison fails, and
shinfo->gso_size and gso_type are not set as they should be.
Instead, add the UDP header length before comparing to gso_size when
using UFO. In this way, it is the size of the IP payload that is
compared to gso_size.
Fixes: 6dd912f826 ("net: check untrusted gso_size at kernel entry")
Signed-off-by: Jonathan Davies <jonathan.davies@nutanix.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b5a333272 ]
Access to netdev after free_netdev() will cause use-after-free bug.
Move debug log before free_netdev() call to avoid it.
Fixes: 7472dd9f64 ("staging: fsl-dpaa2/eth: Move print message")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f799ada6bf ]
Without dropping dst, the packets sent from local mirred/redirected
to ingress will may still use the old dst. ip_rcv() will drop it as
the old dst is for output and its .input is dst_discard.
This patch is to fix by also dropping dst for those packets that are
mirred or redirected from egress to ingress in act_mirred.
Note that we don't drop it for the direction change from ingress to
egress, as on which there might be a user case attaching a metadata
dst by act_tunnel_key that would be used later.
Fixes: b57dc7c13e ("net/sched: Introduce action ct")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Cong Wang <cong.wang@bytedance.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4edd8cd4e8 ]
This fixes a regression added with:
commit f0f82e2476 ("scsi: core: Fix capacity set to zero after
offlinining device")
The problem is that after iSCSI recovery, iscsid will call into the kernel
to set the dev's state to running, and with that patch we now call
scsi_rescan_device() with the state_mutex held. If the SCSI error handler
thread is just starting to test the device in scsi_send_eh_cmnd() then it's
going to try to grab the state_mutex.
We are then stuck, because when scsi_rescan_device() tries to send its I/O
scsi_queue_rq() calls -> scsi_host_queue_ready() -> scsi_host_in_recovery()
which will return true (the host state is still in recovery) and I/O will
just be requeued. scsi_send_eh_cmnd() will then never be able to grab the
state_mutex to finish error handling.
To prevent the deadlock move the rescan-related code to after we drop the
state_mutex.
This also adds a check for if we are already in the running state. This
prevents extra scans and helps the iscsid case where if the transport class
has already onlined the device during its recovery process then we don't
need userspace to do it again plus possibly block that daemon.
Link: https://lore.kernel.org/r/20211105221048.6541-3-michael.christie@oracle.com
Fixes: f0f82e2476 ("scsi: core: Fix capacity set to zero after offlinining device")
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: lijinlin <lijinlin3@huawei.com>
Cc: Wu Bo <wubo40@huawei.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Wu Bo <wubo40@huawei.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4c3176739 ]
On regular ConnectX HCAs getting encap mode isn't supported when the
E-Switch is in NONE mode. Current code would return no error code when
trying to get encap mode in such case which is wrong.
Fix by returning error value to indicate failure to caller in such case.
Fixes: 8e0aa4bc95 ("net/mlx5: E-switch, Protect eswitch mode changes")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c55479d0cb ]
E-Switch mode change routine will take the write lock to prevent any
consumer to access the E-Switch resources while E-Switch is going
through a mode change.
In the next patch
E-Switch consumers (e.g vport representors) will take read_lock prior to
accessing E-Switch resources to prevent E-Switch mode changing in the
middle of the operation.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae396d85c0 ]
Currently, In NETDEV_CHANGELOWERSTATE/NETDEV_CHANGEUPPERSTATE events
handling, tracking is not fully completed if the LAG device is not ready
at the time the events occur. But, we must keep track of the upper and
lower states after receiving the events because RoCE needs this info in
mlx5_lag_get_roce_netdev() - in order to return the corresponding port
that its running on. Returning the wrong (not most recent) port will lead
to gids table being incorrect.
For example: If during the attachment of a slave to the bond, the other
non-attached port performs pci_reload, then the LAG device is not ready,
but that should not result in dismissing attached slave tracker update
automatically (which is performed in mlx5_handle_changelowerstate()), Since
these events might not come later, which can lead to both bond ports
having tx_enabled=0 - which is not a valid state of LAG bond.
Fixes: 9b412cc35f ("net/mlx5e: Add LAG warning if bond slave is not lag master")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 255e51da15 ]
In the case where fw_getenv returns an error when fetching values
for ememsizea and memsize then variable phys_memsize is not assigned
a variable and will be uninitialized on a zero check of phys_memsize.
Fix this by initializing phys_memsize to zero.
Cleans up cppcheck error:
arch/mips/generic/yamon-dt.c:100:7: error: Uninitialized variable: phys_memsize [uninitvar]
Fixes: f41d2430bb ("MIPS: generic/yamon-dt: Support > 256MB of RAM")
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a6e9e483a ]
Now setting combine to 0 will be rejected with the
appropriate error code.
This has been implemented by adding a condition that checks
the value of combine equal to zero.
Without this patch, when the user requested it, no error was
returned and combine was set to the default value for VF.
Fixes: 5520deb153 ("iavf: Enable support for up to 16 queues")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 321421b57a ]
While issuing VF Reset from the guest OS, the VF driver prints
logs about critical / Overflow error detection. This is not an
actual error since the VF_MBX_ARQLEN register is set to all FF's
for a short period of time and the VF would catch the bits set if
it was reading the register during that spike of time.
This patch introduces an additional check to ignore this condition
since the VF is in reset.
Fixes: 19b73d8efa ("i40evf: Add additional check for reset")
Signed-off-by: Surabhi Boob <surabhi.boob@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 131b0edc40 ]
In some cases, the ethtool get_rxfh handler may be called with a null
key or indir parameter. So check these pointers, or you will have a very
bad day.
Fixes: 43a3d9ba34 ("i40evf: Allow PF driver to configure RSS")
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f04008038 ]
In iavf_config_clsflower, the filter structure could be accidentally
released at the end, if iavf_parse_cls_flower or iavf_handle_tclass ever
return a non-zero but positive value.
In this case, the function continues through to the end, and will call
kfree() on the filter structure even though it has been added to the
linked list.
This can actually happen because iavf_parse_cls_flower will return
a positive IAVF_ERR_CONFIG value instead of the traditional negative
error codes.
Fix this by ensuring that the kfree() check and error checks are
similar. Use the more idiomatic "if (err)" to catch all non-zero error
codes.
Fixes: 0075fa0fad ("i40evf: Add support to apply cloud filters")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8905072a19 ]
The driver could only quit allmulti when allmulti and promisc modes are
turn on at the same time. If promisc had been off there was no way to turn
off allmulti mode.
The patch corrects this behavior. Switching allmulti does not depends on
promisc state mode anymore
Fixes: f42a5c74da ("i40e: Add allmulti support for the VF")
Signed-off-by: Piotr Marczak <piotr.marczak@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89f22f1296 ]
iavf_free_queues() clears adapter->num_active_queues, which
iavf_free_q_vectors() relies on, so swap the order of these two function
calls in iavf_disable_vf(). This resolves a panic encountered when the
interface is disabled and then later brought up again after PF
communication is restored.
Fixes: 65c7006f23 ("i40evf: assign num_active_queues inside i40evf_alloc_queues")
Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a4a126f4b ]
If the driver has lost contact with the PF then it enters a disabled state
and frees adapter->vf_res. However, ndo_fix_features can still be called on
the interface, so we need to check for this condition first. Since we have
no information on the features at this time simply leave them unmodified
and return.
Fixes: c4445aedfe ("i40evf: Fix VLAN features")
Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e5e6b5d9d ]
Fixed return correct code from set the new channel count.
Implemented by check if reset is done in appropriate time.
This solution give a extra time to pf for reset vf in case
when user want set new channel count for all vfs.
Without this patch it is possible to return misleading output
code to user and vf reset not to be correctly performed by pf.
Fixes: 5520deb153 ("iavf: Enable support for up to 16 queues")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 938cca9e41 ]
sk_clone_lock() needs to call sock_inuse_add(1) before entering the
sk_free_unlock_clone() error path, for __sk_free() from sk_free() from
sk_free_unlock_clone() calls sock_inuse_add(-1).
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes: 648845ab7e ("sock: Move the socket inuse to namespace.")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 271351d255 ]
The MSG_CRYPTO msgs are always encrypted and sent to other nodes
for keys' deployment. But when receiving in peers, if those nodes
do not validate it and make sure it's encrypted, one could craft
a malicious MSG_CRYPTO msg to deploy its key with no need to know
other nodes' keys.
This patch is to do that by checking TIPC_SKB_CB(skb)->decrypted
and discard it if this packet never got decrypted.
Note that this is also a supplementary fix to CVE-2021-43267 that
can be triggered by an unencrypted malicious MSG_CRYPTO msg.
Fixes: 1ef6f7c939 ("tipc: add automatic session key exchange")
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0757491a1 ]
The driver does not check if hw-tc-offload is enabled for the device
before offloading a flow in the context of indirect block callback.
Fix this by checking NETIF_F_HW_TC in the features flag and rejecting
the offload request. This will avoid unnecessary dmesg error logs when
hw-tc-offload is disabled, such as these:
bnxt_en 0000:19:00.1 eno2np1: dev(ifindex=294) not on same switch
bnxt_en 0000:19:00.1 eno2np1: Error: bnxt_tc_add_flow: cookie=0xffff8dace1c88000 error=-22
bnxt_en 0000:19:00.0 eno1np0: dev(ifindex=294) not on same switch
bnxt_en 0000:19:00.0 eno1np0: Error: bnxt_tc_add_flow: cookie=0xffff8dace1c88000 error=-22
Reported-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Fixes: 627c89d00f ("bnxt_en: flow_offload: offload tunnel decap rules via indirect callbacks")
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8885ac89c ]
Smatch says:
bnx2x_init_ops.h:640 bnx2x_ilt_client_mem_op()
warn: variable dereferenced before check 'ilt' (see line 638)
Move ilt_cli variable initialization _after_ ilt validation, because
it's unsafe to deref the pointer before validation check.
Fixes: 523224a3b3 ("bnx2x, cnic, bnx2i: use new FW/HSI")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 816316caca ]
The head-of-line blocking timer should only be modified when
head-of-line drop is disabled.
One of the steps in recovering from a modem crash is to enable
dropping of packets with timeout of 0 (immediate). We don't know
how the modem configured its endpoints, so before we program the
timer, we need to ensure HOL_BLOCK is disabled.
Fixes: 84f9bd12d4 ("soc: qcom: ipa: IPA endpoints")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 70701b83e2 ]
TCP Receive zerocopy iterates through the SKB queue via
tcp_recv_skb(), acquiring a pointer to an SKB and an offset within
that SKB to read from. From there, it iterates the SKB frags array to
determine which offset to start remapping pages from.
However, this is built on the assumption that the offset read so far
within the SKB is smaller than the SKB length. If this assumption is
violated, we can attempt to read an invalid frags array element, which
would cause a fault.
tcp_recv_skb() can cause such an SKB to be returned when the TCP FIN
flag is set. Therefore, we must guard against this occurrence inside
skb_advance_frag().
One way that we can reproduce this error follows:
1) In a receiver program, call getsockopt(TCP_ZEROCOPY_RECEIVE) with:
char some_array[32 * 1024];
struct tcp_zerocopy_receive zc = {
.copybuf_address = (__u64) &some_array[0],
.copybuf_len = 32 * 1024,
};
2) In a sender program, after a TCP handshake, send the following
sequence of packets:
i) Seq = [X, X+4000]
ii) Seq = [X+4000, X+5000]
iii) Seq = [X+4000, X+5000], Flags = FIN | URG, urgptr=1000
(This can happen without URG, if we have a signal pending, but URG is
a convenient way to reproduce the behaviour).
In this case, the following event sequence will occur on the receiver:
tcp_zerocopy_receive():
-> receive_fallback_to_copy() // copybuf_len >= inq
-> tcp_recvmsg_locked() // reads 5000 bytes, then breaks due to URG
-> tcp_recv_skb() // yields skb with skb->len == offset
-> tcp_zerocopy_set_hint_for_skb()
-> skb_advance_to_frag() // will returns a frags ptr. >= nr_frags
-> find_next_mappable_frag() // will dereference this bad frags ptr.
With this patch, skb_advance_to_frag() will no longer return an
invalid frags pointer, and will return NULL instead, fixing the issue.
Signed-off-by: Arjun Roy <arjunroy@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 05255b823a ("tcp: add TCP_ZEROCOPY_RECEIVE support for zerocopy receive")
Link: https://lore.kernel.org/r/20211111235215.2605384-1-arjunroy.kdev@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7fba5309ef ]
Refactor skb frag fast-forwarding for tcp receive zerocopy. This is
part of a patch set that introduces short-circuited hybrid copies
for small receive operations, which results in roughly 33% fewer
syscalls for small RPC scenarios.
skb_advance_to_frag(), given a skb and an offset into the skb,
iterates from the first frag for the skb until we're at the frag
specified by the offset. Assuming the offset provided refers to how
many bytes in the skb are already read, the returned frag points to
the next frag we may read from, while offset_frag is set to the number
of bytes from this frag that we have already read.
If frag is not null and offset_frag is equal to 0, then we may be able
to map this frag's page into the process address space with
vm_insert_page(). However, if offset_frag is not equal to 0, then we
cannot do so.
Signed-off-by: Arjun Roy <arjunroy@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 18fb76ed53 ]
When TCP receive zerocopy does not successfully map the entire
requested space, it outputs a 'hint' that the caller should recvmsg().
Augment zerocopy to accept a user buffer that it tries to copy this
hint into - if it is possible to copy the entire hint, it will do so.
This elides a recvmsg() call for received traffic that isn't exactly
page-aligned in size.
This was tested with RPC-style traffic of arbitrary sizes. Normally,
each received message required at least one getsockopt() call, and one
recvmsg() call for the remaining unaligned data.
With this change, almost all of the recvmsg() calls are eliminated,
leading to a savings of about 25%-50% in number of system calls
for RPC-style workloads.
Signed-off-by: Arjun Roy <arjunroy@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63f84ae6b8 ]
Do not copy the fixed-size char array field of the events over
the field size. The histogram treats char array as a string and
there are 2 types of char array in the event, fixed-size and
dynamic string. The dynamic string (__data_loc) field must be
null terminated, but the fixed-size char array field may not
be null terminated (not a string, but just a data).
In that case, histogram can copy the data after the field.
This uses the original field size for fixed-size char array
field to restrict the histogram not to access over the original
field size.
Link: https://lkml.kernel.org/r/163673292822.195747.3696966210526410250.stgit@devnote2
Fixes: 02205a6752 (tracing: Add support for 'field variables')
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b781d8db58 ]
KASAN reports a use-after-free report when doing block test:
==================================================================
[10050.967049] BUG: KASAN: use-after-free in
submit_bio_checks+0x1539/0x1550
[10050.977638] Call Trace:
[10050.978190] dump_stack+0x9b/0xce
[10050.979674] print_address_description.constprop.6+0x3e/0x60
[10050.983510] kasan_report.cold.9+0x22/0x3a
[10050.986089] submit_bio_checks+0x1539/0x1550
[10050.989576] submit_bio_noacct+0x83/0xc80
[10050.993714] submit_bio+0xa7/0x330
[10050.994435] mpage_readahead+0x380/0x500
[10050.998009] read_pages+0x1c1/0xbf0
[10051.002057] page_cache_ra_unbounded+0x4c2/0x6f0
[10051.007413] do_page_cache_ra+0xda/0x110
[10051.008207] force_page_cache_ra+0x23d/0x3d0
[10051.009087] page_cache_sync_ra+0xca/0x300
[10051.009970] generic_file_buffered_read+0xbea/0x2130
[10051.012685] generic_file_read_iter+0x315/0x490
[10051.014472] blkdev_read_iter+0x113/0x1b0
[10051.015300] aio_read+0x2ad/0x450
[10051.023786] io_submit_one+0xc8e/0x1d60
[10051.029855] __se_sys_io_submit+0x125/0x350
[10051.033442] do_syscall_64+0x2d/0x40
[10051.034156] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[10051.048733] Allocated by task 18598:
[10051.049482] kasan_save_stack+0x19/0x40
[10051.050263] __kasan_kmalloc.constprop.1+0xc1/0xd0
[10051.051230] kmem_cache_alloc+0x146/0x440
[10051.052060] mempool_alloc+0x125/0x2f0
[10051.052818] bio_alloc_bioset+0x353/0x590
[10051.053658] mpage_alloc+0x3b/0x240
[10051.054382] do_mpage_readpage+0xddf/0x1ef0
[10051.055250] mpage_readahead+0x264/0x500
[10051.056060] read_pages+0x1c1/0xbf0
[10051.056758] page_cache_ra_unbounded+0x4c2/0x6f0
[10051.057702] do_page_cache_ra+0xda/0x110
[10051.058511] force_page_cache_ra+0x23d/0x3d0
[10051.059373] page_cache_sync_ra+0xca/0x300
[10051.060198] generic_file_buffered_read+0xbea/0x2130
[10051.061195] generic_file_read_iter+0x315/0x490
[10051.062189] blkdev_read_iter+0x113/0x1b0
[10051.063015] aio_read+0x2ad/0x450
[10051.063686] io_submit_one+0xc8e/0x1d60
[10051.064467] __se_sys_io_submit+0x125/0x350
[10051.065318] do_syscall_64+0x2d/0x40
[10051.066082] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[10051.067455] Freed by task 13307:
[10051.068136] kasan_save_stack+0x19/0x40
[10051.068931] kasan_set_track+0x1c/0x30
[10051.069726] kasan_set_free_info+0x1b/0x30
[10051.070621] __kasan_slab_free+0x111/0x160
[10051.071480] kmem_cache_free+0x94/0x460
[10051.072256] mempool_free+0xd6/0x320
[10051.072985] bio_free+0xe0/0x130
[10051.073630] bio_put+0xab/0xe0
[10051.074252] bio_endio+0x3a6/0x5d0
[10051.074984] blk_update_request+0x590/0x1370
[10051.075870] scsi_end_request+0x7d/0x400
[10051.076667] scsi_io_completion+0x1aa/0xe50
[10051.077503] scsi_softirq_done+0x11b/0x240
[10051.078344] blk_mq_complete_request+0xd4/0x120
[10051.079275] scsi_mq_done+0xf0/0x200
[10051.080036] virtscsi_vq_done+0xbc/0x150
[10051.080850] vring_interrupt+0x179/0x390
[10051.081650] __handle_irq_event_percpu+0xf7/0x490
[10051.082626] handle_irq_event_percpu+0x7b/0x160
[10051.083527] handle_irq_event+0xcc/0x170
[10051.084297] handle_edge_irq+0x215/0xb20
[10051.085122] asm_call_irq_on_stack+0xf/0x20
[10051.085986] common_interrupt+0xae/0x120
[10051.086830] asm_common_interrupt+0x1e/0x40
==================================================================
Bio will be checked at beginning of submit_bio_noacct(). If bio needs
to be throttled, it will start the timer and stop submit bio directly.
Bio will submit in blk_throtl_dispatch_work_fn() when the timer expires.
But in the current process, if bio is throttled, it will still set bio
issue->value by blkcg_bio_issue_init(). This is redundant and may cause
the above use-after-free.
CPU0 CPU1
submit_bio
submit_bio_noacct
submit_bio_checks
blk_throtl_bio()
<=mod_timer(&sq->pending_timer
blk_throtl_dispatch_work_fn
submit_bio_noacct() <= bio have
throttle tag, will throw directly
and bio issue->value will be set
here
bio_endio()
bio_put()
bio_free() <= free this bio
blkcg_bio_issue_init(bio)
<= bio has been freed and
will lead to UAF
return BLK_QC_T_NONE
Fix this by remove extra blkcg_bio_issue_init.
Fixes: e439bedf6b (blkcg: consolidate bio_issue_init() to be a part of core)
Signed-off-by: Laibin Qiu <qiulaibin@huawei.com>
Link: https://lore.kernel.org/r/20211112093354.3581504-1-qiulaibin@huawei.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42dc938a59 ]
Nothing protects the access to the per_cpu variable sd_llc_id. When testing
the same CPU (i.e. this_cpu == that_cpu), a race condition exists with
update_top_cache_domain(). One scenario being:
CPU1 CPU2
==================================================================
per_cpu(sd_llc_id, CPUX) => 0
partition_sched_domains_locked()
detach_destroy_domains()
cpus_share_cache(CPUX, CPUX) update_top_cache_domain(CPUX)
per_cpu(sd_llc_id, CPUX) => 0
per_cpu(sd_llc_id, CPUX) = CPUX
per_cpu(sd_llc_id, CPUX) => CPUX
return false
ttwu_queue_cond() wouldn't catch smp_processor_id() == cpu and the result
is a warning triggered from ttwu_queue_wakelist().
Avoid a such race in cpus_share_cache() by always returning true when
this_cpu == that_cpu.
Fixes: 518cd62341 ("sched: Only queue remote wakeups when crossing cache boundaries")
Reported-by: Jing-Ting Wu <jing-ting.wu@mediatek.com>
Signed-off-by: Vincent Donnefort <vincent.donnefort@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Reviewed-by: Vincent Guittot <vincent.guittot@linaro.org>
Link: https://lore.kernel.org/r/20211104175120.857087-1-vincent.donnefort@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5eeaafc8d6 ]
Several header files need info on CONFIG_32BIT or CONFIG_64BIT,
but kconfig symbol BCM63XX does not provide that info. This leads
to many build errors, e.g.:
arch/mips/include/asm/page.h:196:13: error: use of undeclared identifier 'CAC_BASE'
return x - PAGE_OFFSET + PHYS_OFFSET;
arch/mips/include/asm/mach-generic/spaces.h:91:23: note: expanded from macro 'PAGE_OFFSET'
#define PAGE_OFFSET (CAC_BASE + PHYS_OFFSET)
arch/mips/include/asm/io.h:134:28: error: use of undeclared identifier 'CAC_BASE'
return (void *)(address + PAGE_OFFSET - PHYS_OFFSET);
arch/mips/include/asm/mach-generic/spaces.h:91:23: note: expanded from macro 'PAGE_OFFSET'
#define PAGE_OFFSET (CAC_BASE + PHYS_OFFSET)
arch/mips/include/asm/uaccess.h:82:10: error: use of undeclared identifier '__UA_LIMIT'
return (__UA_LIMIT & (addr | (addr + size) | __ua_size(size))) == 0;
Selecting the SYS_HAS_CPU_BMIPS* symbols causes SYS_HAS_CPU_BMIPS to be
set, which then selects CPU_SUPPORT_32BIT_KERNEL, which causes
CONFIG_32BIT to be set. (a bit more indirect than v1 [RFC].)
Fixes: e7300d04bd ("MIPS: BCM63xx: Add support for the Broadcom BCM63xx family of SOCs.")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-mips@vger.kernel.org
Cc: Paul Burton <paulburton@kernel.org>
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Ralf Baechle <ralf@linux-mips.org>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05cf3ec00d ]
The gcc_aggre1_pnoc_ahb_clk is crucial for the proper MSM8996/APQ8096
functioning. If it gets disabled, several subsytems will stop working
(including eMMC/SDCC and USB). There are no in-kernel users of this
clock, so it is much simpler to remove from the kernel.
The clock was first removed in the commit 9e60de1cf2 ("clk: qcom:
Remove gcc_aggre1_pnoc_ahb_clk from msm8996") by Stephen Boyd, but got
added back in the commit b567752144 ("clk: qcom: Add some missing gcc
clks for msm8996") by Rajendra Nayak.
Let's remove it again in hope that nobody adds it back.
Reported-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Cc: Konrad Dybcio <konrad.dybcio@somainline.org>
Fixes: b567752144 ("clk: qcom: Add some missing gcc clks for msm8996")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20211104011155.2209654-1-dmitry.baryshkov@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f45c5b1c27 ]
Move the soc revision parsing to the initial probe, saving the driver
from parsing the register multiple times.
Use this variable to select the correct divisor table for the AHB clock.
Before this fix the A2 would have used the A0 table.
Fixes: 2d491066cc ("clk: ast2600: Fix AHB clock divider for A1")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210922235449.213631-1-joel@jms.id.au
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed84ef1cd7 ]
Two fixes in one:
- In the "impose hardware constraints" block, the "logical" divider
value (aka. not translated to the hardware) was clamped to fit in the
register area, but this totally ignored the fact that the divider
value can itself have a fixed divider.
- The code that made sure that the divider value returned by the
function was a multiple of its own fixed divider could result in a
wrong value being calculated, because it was rounded down instead of
rounded up.
Fixes: 4afe2d1a6e ("clk: ingenic: Allow divider value to be divided")
Co-developed-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20211001172033.122329-1-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca98d72141 ]
As Pavel Machek reported in [1]
This code looks quite confused: part of function returns 1 on
corruption, part returns -errno. The problem is not stable-specific.
[1] https://lkml.org/lkml/2021/9/19/207
Let's fix to make 'insane cp_payload case' to return 1 rater than
EFSCORRUPTED, so that return value can be kept consistent for all
error cases, it can avoid confusion of code logic.
Fixes: 65ddf65648 ("f2fs: fix to do sanity check for sb/cp fields correctly")
Reported-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02d58cd253 ]
Compresse file and normal file has differ in i_addr addressing,
specifically addrs per inode/block. So, we will face data loss, if we
disable the compression flag on non-empty files. Therefore we should
disallow not only enabling but disabling the compression flag on
non-empty files.
Fixes: 4c8ff7095b ("f2fs: support data compression")
Signed-off-by: Sungjong Seo <sj1557.seo@samsung.com>
Signed-off-by: Hyeong-Jun Kim <hj514.kim@samsung.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b929926f01 ]
Fix this by defining both ENDIAN macros in
<asm/sfp-machine.h> so that they can be utilized in
<math-emu/soft-fp.h> according to the latter's comment:
/* Allow sfp-machine to have its own byte order definitions. */
(This is what is done in arch/nds32/include/asm/sfp-machine.h.)
This placates these build warnings:
In file included from ../arch/sh/math-emu/math.c:23:
.../include/math-emu/single.h:50:21: warning: "__BIG_ENDIAN" is not defined, evaluates to 0 [-Wundef]
50 | #if __BYTE_ORDER == __BIG_ENDIAN
In file included from ../arch/sh/math-emu/math.c:24:
.../include/math-emu/double.h:59:21: warning: "__BIG_ENDIAN" is not defined, evaluates to 0 [-Wundef]
59 | #if __BYTE_ORDER == __BIG_ENDIAN
Fixes: 4b565680d1 ("sh: math-emu support")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Signed-off-by: Rich Felker <dalias@libc.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e25c252a9b ]
Delete ieee_fpe_handler() since it is not used. After that is done,
delete denormal_to_double() since it is not used:
.../arch/sh/math-emu/math.c:505:12: error: 'ieee_fpe_handler' defined but not used [-Werror=unused-function]
505 | static int ieee_fpe_handler(struct pt_regs *regs)
.../arch/sh/math-emu/math.c:477:13: error: 'denormal_to_double' defined but not used [-Werror=unused-function]
477 | static void denormal_to_double(struct sh_fpu_soft_struct *fpu, int n)
Fixes: 7caf62de25 ("sh: remove unused do_fpu_error")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Takashi YOSHII <takasi-y@ops.dti.ne.jp>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rich Felker <dalias@libc.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 011e0868e0 ]
Since active_logs can be set to 2 or 4 or NR_CURSEG_PERSIST_TYPE(6),
it cannot be set to NR_CURSEG_TYPE(8).
That is, whint_mode is always off.
Therefore, the condition is changed from NR_CURSEG_TYPE to NR_CURSEG_PERSIST_TYPE.
Cc: Chao Yu <chao@kernel.org>
Fixes: d0b9e42ab6 (f2fs: introduce inmem curseg)
Reported-by: tanghuan <tanghuan@vivo.com>
Signed-off-by: Keoseong Park <keosung.park@samsung.com>
Signed-off-by: Fengnan Chang <changfengnan@vivo.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 70a9ac36ff ]
Fix up a misuse that the filename pointer isn't always valid in
the ring buffer, and we should copy the content instead.
Fixes: 0c5e36db17 ("f2fs: trace f2fs_lookup")
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bde82ee391 ]
If KMEM_CACHE or maple_alloc_dev failed, the maple_bus_init() will return 0
rather than error, because the retval is not changed after KMEM_CACHE or
maple_alloc_dev failed.
Fixes: 17be2d2b1c ("sh: Add maple bus support for the SEGA Dreamcast.")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Lu Wei <luwei32@huawei.com>
Acked-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Signed-off-by: Rich Felker <dalias@libc.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fef071be57 ]
In dcr-low.S we use cmpli with three arguments, instead of four
arguments as defined in the ISA:
cmpli cr0,r3,1024
This appears to be a PPC440-ism, looking at the "PPC440x5 CPU Core
User’s Manual" it shows cmpli having no L field, but implied to be 0 due
to the core being 32-bit. It mentions that the ISA defines four
arguments and recommends using cmplwi.
It also corresponds to the old POWER instruction set, which had no L
field there, a reserved bit instead.
dcr-low.S is only built 32-bit, because it is only built when
DCR_NATIVE=y, which is only selected by 40x and 44x. Looking at the
generated code (with gcc/gas) we see cmplwi as expected.
Although gas is happy with the 3-argument version when building for
32-bit, the LLVM assembler is not and errors out with:
arch/powerpc/sysdev/dcr-low.S:27:10: error: invalid operand for instruction
cmpli 0,%r3,1024; ...
^
Switch to the cmplwi extended opcode, which avoids any confusion when
reading the ISA, fixes the issue with the LLVM assembler, and also means
the code could be built 64-bit in future (though that's very unlikely).
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
BugLink: https://github.com/ClangBuiltLinux/linux/issues/1419
Link: https://lore.kernel.org/r/20211014024424.528848-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94be878c88 ]
The length of hw->settings->odr_table is 2 and ref_sensor->id is an enum
variable whose value is between 0 and 5.
However, the value ST_LSM6DSX_ID_MAX (i.e. 5) is not caught properly in
switch (sensor->id) {
If ref_sensor->id is ST_LSM6DSX_ID_MAX, an array overflow will ocurrs in
function st_lsm6dsx_check_odr():
odr_table = &sensor->hw->settings->odr_table[sensor->id];
and in function st_lsm6dsx_set_odr():
reg = &hw->settings->odr_table[ref_sensor->id].reg;
To avoid this array overflow, handle ST_LSM6DSX_ID_GYRO explicitly and
return -EINVAL for the default case.
The enum value ST_LSM6DSX_ID_MAX is only present as an easy way to check
the limit and as such is never used, however this is not locally obvious.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Teng Qi <starmiku1207184332@gmail.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/20211011114003.976221-1-starmiku1207184332@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1283c0d1a3 ]
We can't free the tg_pt_gp in core_alua_set_tg_pt_gp_id() because it's
still accessed via configfs. Its release must go through the normal
configfs/refcount process.
The max alua_tg_pt_gps_count check should probably have been done in
core_alua_allocate_tg_pt_gp(), but with the current code userspace could
have created 0x0000ffff + 1 groups, but only set the id for 0x0000ffff.
Then it could have deleted a group with an ID set, and then set the ID for
that extra group and it would work ok.
It's unlikely, but just in case this patch continues to allow that type of
behavior, and just fixes the kfree() while in use bug.
Link: https://lore.kernel.org/r/20210930020422.92578-4-michael.christie@oracle.com
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed1227e080 ]
This patch fixes the following bugs:
1. If there are multiple ordered cmds queued and multiple simple cmds
completing, target_restart_delayed_cmds() could be called on different
CPUs and each instance could start a ordered cmd. They could then run in
different orders than they were queued.
2. target_restart_delayed_cmds() and target_handle_task_attr() can race
where:
1. target_handle_task_attr() has passed the simple_cmds == 0 check.
2. transport_complete_task_attr() then decrements simple_cmds to 0.
3. transport_complete_task_attr() runs target_restart_delayed_cmds() and
it does not see any cmds on the delayed_cmd_list.
4. target_handle_task_attr() adds the cmd to the delayed_cmd_list.
The cmd will then end up timing out.
3. If we are sent > 1 ordered cmds and simple_cmds == 0, we can execute
them out of order, because target_handle_task_attr() will hit that
simple_cmds check first and return false for all ordered cmds sent.
4. We run target_restart_delayed_cmds() after every cmd completion, so if
there is more than 1 simple cmd running, we start executing ordered cmds
after that first cmd instead of waiting for all of them to complete.
5. Ordered cmds are not supposed to start until HEAD OF QUEUE and all older
cmds have completed, and not just simple.
6. It's not a bug but it doesn't make sense to take the delayed_cmd_lock
for every cmd completion when ordered cmds are almost never used. Just
replacing that lock with an atomic increases IOPs by up to 10% when
completions are spread over multiple CPUs and there are multiple
sessions/ mqs/thread accessing the same device.
This patch moves the queued delayed handling to a per device work to
serialze the cmd executions for each device and adds a new counter to track
HEAD_OF_QUEUE and SIMPLE cmds. We can then check the new counter to
determine when to run the work on the completion path.
Link: https://lore.kernel.org/r/20210930020422.92578-3-michael.christie@oracle.com
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f347c26836 ]
The following issue was observed running syzkaller:
BUG: KASAN: slab-out-of-bounds in memcpy include/linux/string.h:377 [inline]
BUG: KASAN: slab-out-of-bounds in sg_copy_buffer+0x150/0x1c0 lib/scatterlist.c:831
Read of size 2132 at addr ffff8880aea95dc8 by task syz-executor.0/9815
CPU: 0 PID: 9815 Comm: syz-executor.0 Not tainted 4.19.202-00874-gfc0fe04215a9 #2
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xe4/0x14a lib/dump_stack.c:118
print_address_description+0x73/0x280 mm/kasan/report.c:253
kasan_report_error mm/kasan/report.c:352 [inline]
kasan_report+0x272/0x370 mm/kasan/report.c:410
memcpy+0x1f/0x50 mm/kasan/kasan.c:302
memcpy include/linux/string.h:377 [inline]
sg_copy_buffer+0x150/0x1c0 lib/scatterlist.c:831
fill_from_dev_buffer+0x14f/0x340 drivers/scsi/scsi_debug.c:1021
resp_report_tgtpgs+0x5aa/0x770 drivers/scsi/scsi_debug.c:1772
schedule_resp+0x464/0x12f0 drivers/scsi/scsi_debug.c:4429
scsi_debug_queuecommand+0x467/0x1390 drivers/scsi/scsi_debug.c:5835
scsi_dispatch_cmd+0x3fc/0x9b0 drivers/scsi/scsi_lib.c:1896
scsi_request_fn+0x1042/0x1810 drivers/scsi/scsi_lib.c:2034
__blk_run_queue_uncond block/blk-core.c:464 [inline]
__blk_run_queue+0x1a4/0x380 block/blk-core.c:484
blk_execute_rq_nowait+0x1c2/0x2d0 block/blk-exec.c:78
sg_common_write.isra.19+0xd74/0x1dc0 drivers/scsi/sg.c:847
sg_write.part.23+0x6e0/0xd00 drivers/scsi/sg.c:716
sg_write+0x64/0xa0 drivers/scsi/sg.c:622
__vfs_write+0xed/0x690 fs/read_write.c:485
kill_bdev:block_device:00000000e138492c
vfs_write+0x184/0x4c0 fs/read_write.c:549
ksys_write+0x107/0x240 fs/read_write.c:599
do_syscall_64+0xc2/0x560 arch/x86/entry/common.c:293
entry_SYSCALL_64_after_hwframe+0x49/0xbe
We get 'alen' from command its type is int. If userspace passes a large
length we will get a negative 'alen'.
Switch n, alen, and rlen to u32.
Link: https://lore.kernel.org/r/20211013033913.2551004-3-yebin10@huawei.com
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3968ddcf05 ]
When running ltp testcase(ltp/testcases/kernel/pty/pty04.c) with arm64, there is a soft lockup,
which look like this one:
Workqueue: events_unbound flush_to_ldisc
Call trace:
dump_backtrace+0x0/0x1ec
show_stack+0x24/0x30
dump_stack+0xd0/0x128
panic+0x15c/0x374
watchdog_timer_fn+0x2b8/0x304
__run_hrtimer+0x88/0x2c0
__hrtimer_run_queues+0xa4/0x120
hrtimer_interrupt+0xfc/0x270
arch_timer_handler_phys+0x40/0x50
handle_percpu_devid_irq+0x94/0x220
__handle_domain_irq+0x88/0xf0
gic_handle_irq+0x84/0xfc
el1_irq+0xc8/0x180
slip_unesc+0x80/0x214 [slip]
tty_ldisc_receive_buf+0x64/0x80
tty_port_default_receive_buf+0x50/0x90
flush_to_ldisc+0xbc/0x110
process_one_work+0x1d4/0x4b0
worker_thread+0x180/0x430
kthread+0x11c/0x120
In the testcase pty04, The first process call the write syscall to send
data to the pty master. At the same time, the workqueue will do the
flush_to_ldisc to pop data in a loop until there is no more data left.
When the sender and workqueue running in different core, the sender sends
data fastly in full time which will result in workqueue doing work in loop
for a long time and occuring softlockup in flush_to_ldisc with kernel
configured without preempt. So I add need_resched check and cond_resched
in the flush_to_ldisc loop to avoid it.
Signed-off-by: Guanghui Feng <guanghuifeng@linux.alibaba.com>
Link: https://lore.kernel.org/r/1633961304-24759-1-git-send-email-guanghuifeng@linux.alibaba.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c05f1477e ]
On m68k, compiling drivers under SND_ISA causes build errors:
../sound/core/isadma.c: In function 'snd_dma_program':
../sound/core/isadma.c:33:17: error: implicit declaration of function 'claim_dma_lock' [-Werror=implicit-function-declaration]
33 | flags = claim_dma_lock();
| ^~~~~~~~~~~~~~
../sound/core/isadma.c:41:9: error: implicit declaration of function 'release_dma_lock' [-Werror=implicit-function-declaration]
41 | release_dma_lock(flags);
| ^~~~~~~~~~~~~~~~
../sound/isa/sb/sb16_main.c: In function 'snd_sb16_playback_prepare':
../sound/isa/sb/sb16_main.c:253:72: error: 'DMA_AUTOINIT' undeclared (first use in this function)
253 | snd_dma_program(dma, runtime->dma_addr, size, DMA_MODE_WRITE | DMA_AUTOINIT);
| ^~~~~~~~~~~~
../sound/isa/sb/sb16_main.c:253:72: note: each undeclared identifier is reported only once for each function it appears in
../sound/isa/sb/sb16_main.c: In function 'snd_sb16_capture_prepare':
../sound/isa/sb/sb16_main.c:322:71: error: 'DMA_AUTOINIT' undeclared (first use in this function)
322 | snd_dma_program(dma, runtime->dma_addr, size, DMA_MODE_READ | DMA_AUTOINIT);
| ^~~~~~~~~~~~
and more...
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: alsa-devel@alsa-project.org
Cc: linux-m68k@lists.linux-m68k.org
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20211016062602.3588-1-rdunlap@infradead.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05e63b48b2 ]
We cannot list all the possible chips used in different board revisions,
just use the generic "jedec,spi-nor" compatible instead. This also
fixes dtbs_check error:
['jedec,spi-nor', 's25fl256s1', 's25fl512s'] is too long
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Reviewed-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ee1500ef7 ]
This fixes dtbs-check error from simple-bus schema:
soc: thermal-zones: {'type': 'object'} is not allowed for {'cpu-thermal': ..... }
From schema: /home/leo/.local/lib/python3.8/site-packages/dtschema/schemas/simple-bus.yaml
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51b9e22ffd ]
gpmc,mux-add-data is not boolean.
Fixes the below errors flagged by dtbs_check.
"ethernet@4,0:gpmc,mux-add-data: True is not of type 'array'"
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7a07f7b96 ]
The firmware_loader can be used with a pre-allocated buffer
through the use of the API calls:
o request_firmware_into_buf()
o request_partial_firmware_into_buf()
If the firmware was built-in and present, our current check
for if the built-in firmware fits into the pre-allocated buffer
does not return any errors, and we proceed to tell the caller
that everything worked fine. It's a lie and no firmware would
end up being copied into the pre-allocated buffer. So if the
caller trust the result it may end up writing a bunch of 0's
to a device!
Fix this by making the function that checks for the pre-allocated
buffer return non-void. Since the typical use case is when no
pre-allocated buffer is provided make this return successfully
for that case. If the built-in firmware does *not* fit into the
pre-allocated buffer size return a failure as we should have
been doing before.
I'm not aware of users of the built-in firmware using the API
calls with a pre-allocated buffer, as such I doubt this fixes
any real life issue. But you never know... perhaps some oddball
private tree might use it.
In so far as upstream is concerned this just fixes our code for
correctness.
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20210917182226.3532898-2-mcgrof@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f9d618696 ]
The csi_sel mux register is located in the CCM register base and not the
CCM_ANALOG register base. So move it to the correct position in code.
Otherwise changing the parent of the csi clock can lead to a complete
system failure due to the CCM_ANALOG_PLL_SYS_TOG register being falsely
modified.
Also remove the SET_RATE_PARENT flag since one possible supply for the
csi_sel mux is the system PLL which we don't want to modify.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20210927072857.3940880-1-s.riedmueller@phytec.de
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99a7cacc66 ]
According to Documentation/devicetree/bindings/watchdog/arm,sp805.yaml
the compatible is:
compatible = "arm,sp805", "arm,primecell";
The current compatible string doesn't exist at all. Fix it.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f1dcaff64 ]
The entry/exit latency and minimum residency in state for the idle
states of MSM8998 were ..bad: first of all, for all of them the
timings were written for CPU sleep but the min-residency-us param
was miscalculated (supposedly, while porting this from downstream);
Then, the power collapse states are setting PC on both the CPU
cluster *and* the L2 cache, which have different timings: in the
specific case of L2 the times are higher so these ones should be
taken into account instead of the CPU ones.
This parameter misconfiguration was not giving particular issues
because on MSM8998 there was no CPU scaling at all, so cluster/L2
power collapse was rarely (if ever) hit.
When CPU scaling is enabled, though, the wrong timings will produce
SoC unstability shown to the user as random, apparently error-less,
sudden reboots and/or lockups.
This set of parameters are stabilizing the SoC when CPU scaling is
ON and when power collapse is frequently hit.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210901183123.1087392-3-angelogioacchino.delregno@somainline.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6abc4ca5a2 ]
the switch identifies itself as a BCM53012 (rev 5)...
This patch has been tested & verified on OpenWrt's
snapshot with Linux 5.10 (didn't test any older kernels).
The MR32 is able to "talk to the network" as before with
OpenWrt's SWITCHDEV b53 driver.
| b53-srab-switch 18007000.ethernet-switch: found switch: BCM53012, rev 5
| libphy: dsa slave smi: probed
| b53-srab-switch 18007000.ethernet-switch poe (uninitialized):
| PHY [dsa-0.0:00] driver [Generic PHY] (irq=POLL)
| b53-srab-switch 18007000.ethernet-switch: Using legacy PHYLIB callbacks.
| Please migrate to PHYLINK!
| DSA: tree 0 setup
Reported-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7aee0288be ]
AUX2 has slightly wrong voltage and AUX5 doesn't need to be
always on.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9067839ff4 ]
Let's use SYSC_QUIRK_REINIT_ON_CTX_LOST quirk for am335x otg instead of
SYSC_QUIRK_REINIT_ON_RESUME quirk as we can now handle the context loss
in a more generic way.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d88136120 ]
Some interconnect target modules such as otg and gpmc on am335x need a
re-init after resume. As we also have PM runtime cases where the context
may be lost, let's handle these all with cpu_pm.
For the am335x resume path, we already have cpu_pm_resume() call
cpu_pm_cluster_exit().
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 894d4f1f77 ]
According to Documentation/devicetree/bindings/watchdog/arm,sp805.yaml
the compatible is:
compatible = "arm,sp805", "arm,primecell";
The current compatible string doesn't exist at all. Fix it.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2513fa5c25 ]
The CDN DP needs a PHY and a extcon to work correctly. But no extcon is
provided by the device-tree, which leads to an error:
cdn-dp fec00000.dp: [drm:cdn_dp_probe [rockchipdrm]] *ERROR* missing extcon or phy
cdn-dp: probe of fec00000.dp failed with error -22
Disable the CDN DP to make graphic work on the Pinebook Pro.
Reported-by: Guillaume Gardet <guillaume.gardet@arm.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Link: https://lore.kernel.org/r/20210715164101.11486-1-matthias.bgg@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99154581b0 ]
When parsing the txq list in lpfc_drain_txq(), the driver attempts to pass
the requests to the adapter. If such an attempt fails, a local "fail_msg"
string is set and a log message output. The job is then added to a
completions list for cancellation.
Processing of any further jobs from the txq list continues, but since
"fail_msg" remains set, jobs are added to the completions list regardless
of whether a wqe was passed to the adapter. If successfully added to
txcmplq, jobs are added to both lists resulting in list corruption.
Fix by clearing the fail_msg string after adding a job to the completions
list. This stops the subsequent jobs from being added to the completions
list unless they had an appropriate failure.
Link: https://lore.kernel.org/r/20210910233159.115896-2-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15a563d008 ]
Running dtbs_check yielded the issues with bcm-nsp.dtsi.
Firstly this patch fixes the following message by appending "-bus" to
the mpcore node name:
mpcore@19000000: $nodename:0: 'mpcore@19000000' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Secondly mmc node name. The label name can remain as is.
sdhci@21000: $nodename:0: 'sdhci@21000' does not match '^mmc(@.*)?$'
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 167721a590 ]
In kernel 5.4, support has been added for reading MTD devices via the nvmem
API.
For this the mtd devices are registered as read-only NVMEM providers under
sysfs with the same name as the flash partition label property.
So if flash partition label property of multiple flash devices are
identical then the second mtd device fails to get registered as a NVMEM
provider.
This patch fixes the issue by having different label property for different
flashes.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/6c4b9b9232b93d9e316a63c086540fd5bf6b8687.1623684253.git.michal.simek@xilinx.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Add these missing V4L2 controls. Tested binned and full resolution
modes in all four orientations using Raspberry Pi running libcamera.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
commit 98481f3d72 upstream.
The PCIe host bridge has two interrupt lines, one that goes towards it
PCIE_INTR2 second level interrupt controller and one for its MSI second
level interrupt controller. The first interrupt line is not currently
managed by the driver, which is why it was not a functional problem.
The interrupt-map property was also only listing the PCI_INTA interrupts
when there are also the INTB, C and D.
Reported-by: Jim Quinlan <jim2101024@gmail.com>
Fixes: d5c8dc0d4c ("ARM: dts: bcm2711: Enable PCIe controller")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add a second (identical) set of device nodes to allow concurrent use of the ISP
hardware by another user. This change effectively creates a second state
structure (struct bcm2835_isp_dev) to maintain independent state for the second
user. Node and media entity names are appened with the instance index
appropriately.
Further users can be added by changing the BCM2835_ISP_NUM_INSTANCES define.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
commit a72fdfd21e upstream.
Commit in Fixes changed the iopl emulation to not #GP on CLI and STI
because it would break some insane luserspace tools which would toggle
interrupts.
The corresponding selftest would rely on the fact that executing CLI/STI
would trigger a #GP and thus detect it this way but since that #GP is
not happening anymore, the detection is now wrong too.
Extend the test to actually look at the IF flag and whether executing
those insns had any effect on it. The STI detection needs to have the
fact that interrupts were previously disabled, passed in so do that from
the previous CLI test, i.e., STI test needs to follow a previous CLI one
for it to make sense.
Fixes: b968e84b50 ("x86/iopl: Fake iopl(3) CLI/STI usage")
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20211030083939.13073-1-bp@alien8.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 96cfe05051 upstream.
of_parse_thermal_zones() parses the thermal-zones node and registers a
thermal_zone device for each subnode. However, if a thermal zone is
consuming a thermal sensor and that thermal sensor device hasn't probed
yet, an attempt to set trip_point_*_temp for that thermal zone device
can cause a NULL pointer dereference. Fix it.
console:/sys/class/thermal/thermal_zone87 # echo 120000 > trip_point_0_temp
...
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000020
...
Call trace:
of_thermal_set_trip_temp+0x40/0xc4
trip_point_temp_store+0xc0/0x1dc
dev_attr_store+0x38/0x88
sysfs_kf_write+0x64/0xc0
kernfs_fop_write_iter+0x108/0x1d0
vfs_write+0x2f4/0x368
ksys_write+0x7c/0xec
__arm64_sys_write+0x20/0x30
el0_svc_common.llvm.7279915941325364641+0xbc/0x1bc
do_el0_svc+0x28/0xa0
el0_svc+0x14/0x24
el0_sync_handler+0x88/0xec
el0_sync+0x1c0/0x200
While at it, fix the possible NULL pointer dereference in other
functions as well: of_thermal_get_temp(), of_thermal_set_emul_temp(),
of_thermal_get_trend().
Suggested-by: David Collins <quic_collinsd@quicinc.com>
Signed-off-by: Subbaraman Narayanamurthy <quic_subbaram@quicinc.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4716023a8f upstream.
PEBS PERF_SAMPLE_PHYS_ADDR events use perf_virt_to_phys() to convert PMU
sampled virtual addresses to physical using get_user_page_fast_only()
and page_to_phys().
Some get_user_page_fast_only() error cases return false, indicating no
page reference, but still initialize the output page pointer with an
unreferenced page. In these error cases perf_virt_to_phys() calls
put_page(). This causes page reference count underflow, which can lead
to unintentional page sharing.
Fix perf_virt_to_phys() to only put_page() if get_user_page_fast_only()
returns a referenced page.
Fixes: fc7ce9c74c ("perf/core, x86: Add PERF_SAMPLE_PHYS_ADDR")
Signed-off-by: Greg Thelen <gthelen@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20211111021814.757086-1-gthelen@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is for linux-5.10.y only.
When scripts/lld-version.sh was initially written, it did not account
for the LLD_VENDOR cmake flag, which changes the output of ld.lld's
--version flag slightly.
Without LLD_VENDOR:
$ ld.lld --version
LLD 14.0.0 (compatible with GNU linkers)
With LLD_VENDOR:
$ ld.lld --version
Debian LLD 14.0.0 (compatible with GNU linkers)
As a result, CONFIG_LLD_VERSION is messed up and configuration values
that are dependent on it cannot be selected:
scripts/lld-version.sh: 20: printf: LLD: expected numeric value
scripts/lld-version.sh: 20: printf: LLD: expected numeric value
scripts/lld-version.sh: 20: printf: LLD: expected numeric value
init/Kconfig:52:warning: 'LLD_VERSION': number is invalid
.config:11:warning: symbol value '00000' invalid for LLD_VERSION
.config:8800:warning: override: CPU_BIG_ENDIAN changes choice state
This was fixed upstream by commit 1f09af0625 ("kbuild: Fix
ld-version.sh script if LLD was built with LLD_VENDOR") in 5.12 but that
was done to ld-version.sh after it was massively rewritten in
commit 02aff85922 ("kbuild: check the minimum linker version in
Kconfig").
To avoid bringing in that change plus its prerequisites and fixes, just
modify lld-version.sh to make it similar to the upstream ld-version.sh,
which handles ld.lld with or without LLD_VENDOR and ld.bfd without any
errors.
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 86432a6dca upstream.
There are pclusters in runtime marked with Z_EROFS_PCLUSTER_TAIL
before actual I/O submission. Thus, the decompression chain can be
extended if the following pcluster chain hooks such tail pcluster.
As the related comment mentioned, if some page is made of a hooked
pcluster and another followed pcluster, it can be reused for in-place
I/O (since I/O should be submitted anyway):
_______________________________________________________________
| tail (partial) page | head (partial) page |
|_____PRIMARY_HOOKED___|____________PRIMARY_FOLLOWED____________|
However, it's by no means safe to reuse as pagevec since if such
PRIMARY_HOOKED pclusters finally move into bypass chain without I/O
submission. It's somewhat hard to reproduce with LZ4 and I just found
it (general protection fault) by ro_fsstressing a LZMA image for long
time.
I'm going to actively clean up related code together with multi-page
folio adaption in the next few months. Let's address it directly for
easier backporting for now.
Call trace for reference:
z_erofs_decompress_pcluster+0x10a/0x8a0 [erofs]
z_erofs_decompress_queue.isra.36+0x3c/0x60 [erofs]
z_erofs_runqueue+0x5f3/0x840 [erofs]
z_erofs_readahead+0x1e8/0x320 [erofs]
read_pages+0x91/0x270
page_cache_ra_unbounded+0x18b/0x240
filemap_get_pages+0x10a/0x5f0
filemap_read+0xa9/0x330
new_sync_read+0x11b/0x1a0
vfs_read+0xf1/0x190
Link: https://lore.kernel.org/r/20211103182006.4040-1-xiang@kernel.org
Fixes: 3883a79abd ("staging: erofs: introduce VLE decompression support")
Cc: <stable@vger.kernel.org> # 4.19+
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ec18fc783 upstream.
commit 8779e05ba8 ("parisc: Fix ptrace check on syscall return")
fixed testing of TI_FLAGS. This uncovered a bug in the test mask.
syscall_restore_rfi is only used when the kernel needs to exit to
usespace with single or block stepping and the recovery counter
enabled. The test however used _TIF_SYSCALL_TRACE_MASK, which
includes a lot of bits that shouldn't be tested here.
Fix this by using TIF_SINGLESTEP and TIF_BLOCKSTEP directly.
I encountered this bug by enabling syscall tracepoints. Both in qemu and
on real hardware. As soon as i enabled the tracepoint (sys_exit_read,
but i guess it doesn't really matter which one), i got random page
faults in userspace almost immediately.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b968e84b50 upstream.
Since commit c8137ace56 ("x86/iopl: Restrict iopl() permission
scope") it's possible to emulate iopl(3) using ioperm(), except for
the CLI/STI usage.
Userspace CLI/STI usage is very dubious (read broken), since any
exception taken during that window can lead to rescheduling anyway (or
worse). The IOPL(2) manpage even states that usage of CLI/STI is highly
discouraged and might even crash the system.
Of course, that won't stop people and HP has the dubious honour of
being the first vendor to be found using this in their hp-health
package.
In order to enable this 'software' to still 'work', have the #GP treat
the CLI/STI instructions as NOPs when iopl(3). Warn the user that
their program is doing dubious things.
Fixes: a24ca99768 ("x86/iopl: Remove legacy IOPL option")
Reported-by: Ondrej Zary <linux@zary.sk>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org # v5.5+
Link: https://lkml.kernel.org/r/20210918090641.GD5106@worktop.programming.kicks-ass.net
Signed-off-by: Ondrej Zary <linux@zary.sk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2d26f6e39a upstream.
This reverts commit 2c896fb02e
"net: stmmac: dwmac-rk: add pd_gmac support for rk3399" and fixes
unbalanced pm_runtime_enable warnings.
In the commit to be reverted, support for power management was
introduced to the Rockchip glue code. Later, power management support
was introduced to the stmmac core code, resulting in multiple
invocations of pm_runtime_{enable,disable,get_sync,put_sync}.
The multiple invocations happen in rk_gmac_powerup and
stmmac_{dvr_probe, resume} as well as in rk_gmac_powerdown and
stmmac_{dvr_remove, suspend}, respectively, which are always called
in conjunction.
Fixes: 5ec5582343 ("net: stmmac: add clocks management for gmac driver")
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4691ffb18a upstream.
Fix system hang with below sequences:
~# ifconfig ethx down
~# ifconfig ethx hw ether xx:xx:xx:xx:xx:xx
After ethx down, stmmac all clocks gated off and then register access causes
system hang.
Fixes: 5ec5582343 ("net: stmmac: add clocks management for gmac driver")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ec05a6035 upstream
Get rid of the CONFIG_PM_SLEEP ifdefery to fix the build error
and use __maybe_unused for the suspend()/resume() hooks to avoid
build warning:
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:769:21:
error: 'stmmac_runtime_suspend' undeclared here (not in a function); did you mean 'stmmac_suspend'?
769 | SET_RUNTIME_PM_OPS(stmmac_runtime_suspend, stmmac_runtime_resume, NULL)
| ^~~~~~~~~~~~~~~~~~~~~~
./include/linux/pm.h:342:21: note: in definition of macro 'SET_RUNTIME_PM_OPS'
342 | .runtime_suspend = suspend_fn, \
| ^~~~~~~~~~
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:769:45:
error: 'stmmac_runtime_resume' undeclared here (not in a function)
769 | SET_RUNTIME_PM_OPS(stmmac_runtime_suspend, stmmac_runtime_resume, NULL)
| ^~~~~~~~~~~~~~~~~~~~~
./include/linux/pm.h:343:20: note: in definition of macro 'SET_RUNTIME_PM_OPS'
343 | .runtime_resume = resume_fn, \
| ^~~~~~~~~
Fixes: 5ec5582343 ("net: stmmac: add clocks management for gmac driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ec5582343 upstream.
This patch intends to add clocks management for stmmac driver:
If CONFIG_PM enabled:
1. Keep clocks disabled after driver probed.
2. Enable clocks when up the net device, and disable clocks when down
the net device.
If CONFIG_PM disabled:
Keep clocks always enabled after driver probed.
Note:
1. It is fine for ethtool, since the way of implementing ethtool_ops::begin
in stmmac is only can be accessed when interface is enabled, so the clocks
are ticked.
2. The MDIO bus has a different life cycle to the MAC, need ensure
clocks are enabled when _mdio_read/write() need clocks, because these
functions can be called while the interface it not opened.
Stable backport notes:
When run below command to remove ethernet driver on
stratix10 platform, there will be warning trace as below:
$ cd /sys/class/net/eth0/device/driver/
$ echo ff800000.ethernet > unbind
WARNING: CPU: 3 PID: 386 at drivers/clk/clk.c:810 clk_core_unprepare+0x114/0x274
Modules linked in: sch_fq_codel
CPU: 3 PID: 386 Comm: sh Tainted: G W 5.10.74-yocto-standard #1
Hardware name: SoCFPGA Stratix 10 SoCDK (DT)
pstate: 00000005 (nzcv daif -PAN -UAO -TCO BTYPE=--)
pc : clk_core_unprepare+0x114/0x274
lr : clk_core_unprepare+0x114/0x274
sp : ffff800011bdbb10
clk_core_unprepare+0x114/0x274
clk_unprepare+0x38/0x50
stmmac_remove_config_dt+0x40/0x80
stmmac_pltfr_remove+0x64/0x80
platform_drv_remove+0x38/0x60
... ..
el0_sync_handler+0x1a4/0x1b0
el0_sync+0x180/0x1c0
This issue is introduced by introducing upstream commit 8f269102ba
("net: stmmac: disable clocks in stmmac_remove_config_dt()")
But in latest mainline kernel, there is no this issue. Because this
patch improved clocks management for stmmac driver.
Therefore, backport it and its fixing patches to stable kernel v5.10.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: stable@vger.kernel.org
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 541ac97186 upstream.
The size of the exception stacks was increased by the commit in Fixes,
resulting in stack sizes greater than a page in size. The #VC exception
handling was only mapping the first (bottom) page, resulting in an
SEV-ES guest failing to boot.
Make the #VC exception stacks part of the default exception stacks
storage and allocate them with a CONFIG_AMD_MEM_ENCRYPT=y .config. Map
them only when a SEV-ES guest has been detected.
Rip out the custom VC stacks mapping and storage code.
[ bp: Steal and adapt Tom's commit message. ]
Fixes: 7fae4c24a2 ("x86: Increase exception stack sizes")
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Tested-by: Brijesh Singh <brijesh.singh@amd.com>
Link: https://lkml.kernel.org/r/YVt1IMjIs7pIZTRR@zn.tnic
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a20eac0af0 upstream.
Previous fix aded bpf_clamp_umax() helper use to re-validate boundaries.
While that works correctly, it introduces more branches, which blows up
past 1 million instructions in no-alu32 variant of strobemeta selftests.
Switching len variable from u32 to u64 also fixes the issue and reduces
the number of validated instructions, so use that instead. Fix this
patch and bpf_clamp_umax() removed, both alu32 and no-alu32 selftests
pass.
Fixes: 0133c20480 ("selftests/bpf: Fix strobemeta selftest regression")
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20211101230118.1273019-1-andrii@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0eab756f88 upstream.
There are several error return paths that dereference the null pointer
host because the pointer has not yet been set to a valid value.
Fix this by adding a new out_mmc label and exiting via this label
to avoid the host clean up and hence the null pointer dereference.
Addresses-Coverity: ("Explicit null dereference")
Fixes: 8105c2abbf ("mmc: moxart: Fix reference count leaks in moxart_probe")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20211013100052.125461-1-colin.king@canonical.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 937e79c677 upstream.
Using a kernel pointer in place of a dma_addr_t token can
lead to undefined behavior if that makes it into cache
management functions. The compiler caught one such attempt
in a cast:
drivers/net/wireless/ath/ath10k/mac.c: In function 'ath10k_add_interface':
drivers/net/wireless/ath/ath10k/mac.c:5586:47: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
5586 | arvif->beacon_paddr = (dma_addr_t)arvif->beacon_buf;
| ^
Looking through how this gets used down the way, I'm fairly
sure that beacon_paddr is never accessed again for ATH10K_DEV_TYPE_HL
devices, and if it was accessed, that would be a bug.
Change the assignment to use a known-invalid address token
instead, which avoids the warning and makes it easier to catch
bugs if it does end up getting used.
Fixes: e263bdab9c ("ath10k: high latency fixes for beacon buffer")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211014075153.3655910-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea7a1019d8 upstream.
The premise of commit 6f9f17287e ("SUNRPC: Mitigate cond_resched() in
xprt_transmit()") was that cond_resched() is expensive and unnecessary
when there has been just a single send.
The point of cond_resched() is to ensure that tasks that should pre-empt
this one get a chance to do so when it is safe to do so. The code prior
to commit 6f9f17287e failed to take into account that it was keeping a
rpc_task pinned for longer than it needed to, and so rather than doing a
full revert, let's just move the cond_resched.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4e17d65da upstream.
Change PCIe Max Payload Size setting in PCIe Device Control register to 512
bytes to align with PCIe Link Initialization sequence as defined in Marvell
Armada 3700 Functional Specification. According to the specification,
maximal Max Payload Size supported by this device is 512 bytes.
Without this kernel prints suspicious line:
pci 0000:01:00.0: Upstream bridge's Max Payload Size set to 256 (was 16384, max 512)
With this change it changes to:
pci 0000:01:00.0: Upstream bridge's Max Payload Size set to 256 (was 512, max 512)
Link: https://lore.kernel.org/r/20211005180952.6812-3-kabel@kernel.org
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c45361abb9 upstream.
When CONFIG_SMP=y, timebase synchronization is required when the second
kernel is started.
arch/powerpc/kernel/smp.c:
int __cpu_up(unsigned int cpu, struct task_struct *tidle)
{
...
if (smp_ops->give_timebase)
smp_ops->give_timebase();
...
}
void start_secondary(void *unused)
{
...
if (smp_ops->take_timebase)
smp_ops->take_timebase();
...
}
When CONFIG_HOTPLUG_CPU=n and CONFIG_KEXEC_CORE=n,
smp_85xx_ops.give_timebase is NULL,
smp_85xx_ops.take_timebase is NULL,
As a result, the timebase is not synchronized.
Timebase synchronization does not depend on CONFIG_HOTPLUG_CPU.
Fixes: 56f1ba2807 ("powerpc/mpc85xx: refactor the PM operations")
Cc: stable@vger.kernel.org # v4.6+
Signed-off-by: Xiaoming Ni <nixiaoming@huawei.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210929033646.39630-3-nixiaoming@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e3cdba176 upstream.
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: dbffc8ccdf ("mtd: rawnand: au1550: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-3-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 325fd539fc upstream.
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 612e048e6a ("mtd: rawnand: plat_nand: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-8-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 194ac63de6 upstream.
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 553508cec2 ("mtd: rawnand: orion: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-6-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f16b7d2a5e upstream.
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 8fc6f1f042 ("mtd: rawnand: pasemi: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-7-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5b5b4dc6f upstream.
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: f6341f6448 ("mtd: rawnand: gpio: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-4-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9d8570b7f upstream.
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 6dd09f775b ("mtd: rawnand: mpc5121: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-5-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6bcd2960af upstream.
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: d525914b5b ("mtd: rawnand: xway: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Cc: Jan Hoffmann <jan@3e8.eu>
Cc: Kestrel seventyfour <kestrelseventyfour@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Jan Hoffmann <jan@3e8.eu>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-10-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d707bb74da upstream.
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 59d9347332 ("mtd: rawnand: ams-delta: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-2-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad9a145172 upstream.
Since commit 48720ba568 ("virtio/s390: use DMA memory for ccw I/O and
classic notifiers") we were supposed to make sure that
virtio_ccw_release_dev() completes before the ccw device and the
attached dma pool are torn down, but unfortunately we did not. Before
that commit it used to be OK to delay cleaning up the memory allocated
by virtio-ccw indefinitely (which isn't really intuitive for guys used
to destruction happens in reverse construction order), but now we
trigger a BUG_ON if the genpool is destroyed before all memory allocated
from it is deallocated. Which brings down the guest. We can observe this
problem, when unregister_virtio_device() does not give up the last
reference to the virtio_device (e.g. because a virtio-scsi attached scsi
disk got removed without previously unmounting its previously mounted
partition).
To make sure that the genpool is only destroyed after all the necessary
freeing is done let us take a reference on the ccw device on each
ccw_device_dma_zalloc() and give it up on each ccw_device_dma_free().
Actually there are multiple approaches to fixing the problem at hand
that can work. The upside of this one is that it is the safest one while
remaining simple. We don't crash the guest even if the driver does not
pair allocations and frees. The downside is the reference counting
overhead, that the reference counting for ccw devices becomes more
complex, in a sense that we need to pair the calls to the aforementioned
functions for it to be correct, and that if we happen to leak, we leak
more than necessary (the whole ccw device instead of just the genpool).
Some alternatives to this approach are taking a reference in
virtio_ccw_online() and giving it up in virtio_ccw_release_dev() or
making sure virtio_ccw_release_dev() completes its work before
virtio_ccw_remove() returns. The downside of these approaches is that
these are less safe against programming errors.
Cc: <stable@vger.kernel.org> # v5.3
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Fixes: 48720ba568 ("virtio/s390: use DMA memory for ccw I/O and classic notifiers")
Reported-by: bfu@redhat.com
Reviewed-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3826350e6d upstream.
When a queue is switched to soft offline during heavy load and later
switched to soft online again and now used, it may be that the caller
is blocked forever in the ioctl call.
The failure occurs because there is a pending reply after the queue(s)
have been switched to offline. This orphaned reply is received when
the queue is switched to online and is accidentally counted for the
outstanding replies. So when there was a valid outstanding reply and
this orphaned reply is received it counts as the outstanding one thus
dropping the outstanding counter to 0. Voila, with this counter the
receive function is not called any more and the real outstanding reply
is never received (until another request comes in...) and the ioctl
blocks.
The fix is simple. However, instead of readjusting the counter when an
orphaned reply is detected, I check the queue status for not empty and
compare this to the outstanding counter. So if the queue is not empty
then the counter must not drop to 0 but at least have a value of 1.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 213fca9e23 upstream.
commit 9c6c273aa4 ("timer: Remove init_timer_on_stack() in favor
of timer_setup_on_stack()") changed the timer setup from
init_timer_on_stack(() to timer_setup(), but missed to change the
mod_timer() call. And while at it, use msecs_to_jiffies() instead
of the open coded timeout calculation.
Cc: stable@vger.kernel.org
Fixes: 9c6c273aa4 ("timer: Remove init_timer_on_stack() in favor of timer_setup_on_stack()")
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33a5471f8d upstream.
The note in c2adda27d2 ("video: backlight: Add of_find_backlight helper
in backlight.c") says that gpio-backlight uses brightness as power state.
This has been fixed since in ec665b756e ("backlight: gpio-backlight:
Correct initial power state handling") and other backlight drivers do not
require this workaround. Drop the workaround.
This fixes the case where e.g. pwm-backlight can perfectly well be set to
brightness 0 on boot in DT, which without this patch leads to the display
brightness to be max instead of off.
Fixes: c2adda27d2 ("video: backlight: Add of_find_backlight helper in backlight.c")
Cc: <stable@vger.kernel.org> # 5.4+
Cc: <stable@vger.kernel.org> # 4.19.x: ec665b756e: backlight: gpio-backlight: Correct initial power state handling
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60e2793d44 upstream.
Any allocation failure during the #PF path will return with VM_FAULT_OOM
which in turn results in pagefault_out_of_memory. This can happen for 2
different reasons. a) Memcg is out of memory and we rely on
mem_cgroup_oom_synchronize to perform the memcg OOM handling or b)
normal allocation fails.
The latter is quite problematic because allocation paths already trigger
out_of_memory and the page allocator tries really hard to not fail
allocations. Anyway, if the OOM killer has been already invoked there
is no reason to invoke it again from the #PF path. Especially when the
OOM condition might be gone by that time and we have no way to find out
other than allocate.
Moreover if the allocation failed and the OOM killer hasn't been invoked
then we are unlikely to do the right thing from the #PF context because
we have already lost the allocation context and restictions and
therefore might oom kill a task from a different NUMA domain.
This all suggests that there is no legitimate reason to trigger
out_of_memory from pagefault_out_of_memory so drop it. Just to be sure
that no #PF path returns with VM_FAULT_OOM without allocation print a
warning that this is happening before we restart the #PF.
[VvS: #PF allocation can hit into limit of cgroup v1 kmem controller.
This is a local problem related to memcg, however, it causes unnecessary
global OOM kills that are repeated over and over again and escalate into a
real disaster. This has been broken since kmem accounting has been
introduced for cgroup v1 (3.8). There was no kmem specific reclaim for
the separate limit so the only way to handle kmem hard limit was to return
with ENOMEM. In upstream the problem will be fixed by removing the
outdated kmem limit, however stable and LTS kernels cannot do it and are
still affected. This patch fixes the problem and should be backported
into stable/LTS.]
Link: https://lkml.kernel.org/r/f5fd8dd8-0ad4-c524-5f65-920b01972a42@virtuozzo.com
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Roman Gushchin <guro@fb.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Cc: Uladzislau Rezki <urezki@gmail.com>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b28179a61 upstream.
Patch series "memcg: prohibit unconditional exceeding the limit of dying tasks", v3.
Memory cgroup charging allows killed or exiting tasks to exceed the hard
limit. It can be misused and allowed to trigger global OOM from inside
a memcg-limited container. On the other hand if memcg fails allocation,
called from inside #PF handler it triggers global OOM from inside
pagefault_out_of_memory().
To prevent these problems this patchset:
(a) removes execution of out_of_memory() from
pagefault_out_of_memory(), becasue nobody can explain why it is
necessary.
(b) allow memcg to fail allocation of dying/killed tasks.
This patch (of 3):
Any allocation failure during the #PF path will return with VM_FAULT_OOM
which in turn results in pagefault_out_of_memory which in turn executes
out_out_memory() and can kill a random task.
An allocation might fail when the current task is the oom victim and
there are no memory reserves left. The OOM killer is already handled at
the page allocator level for the global OOM and at the charging level
for the memcg one. Both have much more information about the scope of
allocation/charge request. This means that either the OOM killer has
been invoked properly and didn't lead to the allocation success or it
has been skipped because it couldn't have been invoked. In both cases
triggering it from here is pointless and even harmful.
It makes much more sense to let the killed task die rather than to wake
up an eternally hungry oom-killer and send him to choose a fatter victim
for breakfast.
Link: https://lkml.kernel.org/r/0828a149-786e-7c06-b70a-52d086818ea3@virtuozzo.com
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Suggested-by: Michal Hocko <mhocko@suse.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Roman Gushchin <guro@fb.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Cc: Uladzislau Rezki <urezki@gmail.com>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4ebf1b6ca upstream.
Memory cgroup charging allows killed or exiting tasks to exceed the hard
limit. It is assumed that the amount of the memory charged by those
tasks is bound and most of the memory will get released while the task
is exiting. This is resembling a heuristic for the global OOM situation
when tasks get access to memory reserves. There is no global memory
shortage at the memcg level so the memcg heuristic is more relieved.
The above assumption is overly optimistic though. E.g. vmalloc can
scale to really large requests and the heuristic would allow that. We
used to have an early break in the vmalloc allocator for killed tasks
but this has been reverted by commit b8c8a338f7 ("Revert "vmalloc:
back off when the current task is killed""). There are likely other
similar code paths which do not check for fatal signals in an
allocation&charge loop. Also there are some kernel objects charged to a
memcg which are not bound to a process life time.
It has been observed that it is not really hard to trigger these
bypasses and cause global OOM situation.
One potential way to address these runaways would be to limit the amount
of excess (similar to the global OOM with limited oom reserves). This
is certainly possible but it is not really clear how much of an excess
is desirable and still protects from global OOMs as that would have to
consider the overall memcg configuration.
This patch is addressing the problem by removing the heuristic
altogether. Bypass is only allowed for requests which either cannot
fail or where the failure is not desirable while excess should be still
limited (e.g. atomic requests). Implementation wise a killed or dying
task fails to charge if it has passed the OOM killer stage. That should
give all forms of reclaim chance to restore the limit before the failure
(ENOMEM) and tell the caller to back off.
In addition, this patch renames should_force_charge() helper to
task_is_dying() because now its use is not associated witch forced
charging.
This patch depends on pagefault_out_of_memory() to not trigger
out_of_memory(), because then a memcg failure can unwind to VM_FAULT_OOM
and cause a global OOM killer.
Link: https://lkml.kernel.org/r/8f5cebbb-06da-4902-91f0-6566fc4b4203@virtuozzo.com
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Suggested-by: Michal Hocko <mhocko@suse.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: Uladzislau Rezki <urezki@gmail.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3dc20f4762 ]
Currently, it is not possible to migrate a neighbor entry between NUD_PERMANENT
state and NTF_USE flag with a dynamic NUD state from a user space control plane.
Similarly, it is not possible to add/remove NTF_EXT_LEARNED flag from an existing
neighbor entry in combination with NTF_USE flag.
This is due to the latter directly calling into neigh_event_send() without any
meta data updates as happening in __neigh_update(). Thus, to enable this use
case, extend the latter with a NEIGH_UPDATE_F_USE flag where we break the
NUD_PERMANENT state in particular so that a latter neigh_event_send() is able
to re-resolve a neighbor entry.
Before fix, NUD_PERMANENT -> NUD_* & NTF_USE:
# ./ip/ip n replace 192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a PERMANENT
[...]
# ./ip/ip n replace 192.168.178.30 dev enp5s0 use extern_learn
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a PERMANENT
[...]
As can be seen, despite the admin-triggered replace, the entry remains in the
NUD_PERMANENT state.
After fix, NUD_PERMANENT -> NUD_* & NTF_USE:
# ./ip/ip n replace 192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a PERMANENT
[...]
# ./ip/ip n replace 192.168.178.30 dev enp5s0 use extern_learn
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a extern_learn REACHABLE
[...]
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a extern_learn STALE
[...]
# ./ip/ip n replace 192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a PERMANENT
[...]
After the fix, the admin-triggered replace switches to a dynamic state from
the NTF_USE flag which triggered a new neighbor resolution. Likewise, we can
transition back from there, if needed, into NUD_PERMANENT.
Similar before/after behavior can be observed for below transitions:
Before fix, NTF_USE -> NTF_USE | NTF_EXT_LEARNED -> NTF_USE:
# ./ip/ip n replace 192.168.178.30 dev enp5s0 use
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a REACHABLE
[...]
# ./ip/ip n replace 192.168.178.30 dev enp5s0 use extern_learn
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a REACHABLE
[...]
After fix, NTF_USE -> NTF_USE | NTF_EXT_LEARNED -> NTF_USE:
# ./ip/ip n replace 192.168.178.30 dev enp5s0 use
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a REACHABLE
[...]
# ./ip/ip n replace 192.168.178.30 dev enp5s0 use extern_learn
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a extern_learn REACHABLE
[...]
# ./ip/ip n replace 192.168.178.30 dev enp5s0 use
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a REACHABLE
[..]
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Roopa Prabhu <roopa@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 69ea463021 upstream.
When using "devm_request_threaded_irq(,,,,IRQF_ONESHOT,,)" in a driver,
only the first interrupt is handled, and following interrupts are never
delivered (initially reported in [1]).
That's because the RISC-V PLIC cannot EOI masked interrupts, as explained
in the description of Interrupt Completion in the PLIC spec [2]:
<quote>
The PLIC signals it has completed executing an interrupt handler by
writing the interrupt ID it received from the claim to the claim/complete
register. The PLIC does not check whether the completion ID is the same
as the last claim ID for that target. If the completion ID does not match
an interrupt source that *is currently enabled* for the target, the
completion is silently ignored.
</quote>
Re-enable the interrupt before completion if it has been masked during
the handling, and remask it afterwards.
[1] http://lists.infradead.org/pipermail/linux-riscv/2021-July/007441.html
[2] 8bc15a35d0/riscv-plic.adoc
Fixes: bb0fed1c60 ("irqchip/sifive-plic: Switch to fasteoi flow")
Reported-by: Vincent Pelletier <plr.vincent@gmail.com>
Tested-by: Nikita Shubin <nikita.shubin@maquefel.me>
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Cc: stable@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
[maz: amended commit message]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211105094748.3894453-1-guoren@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca7752caea upstream.
copy_process currently copies task_struct.posix_cputimers_work as-is. If a
timer interrupt arrives while handling clone and before dup_task_struct
completes then the child task will have:
1. posix_cputimers_work.scheduled = true
2. posix_cputimers_work.work queued.
copy_process clears task_struct.task_works, so (2) will have no effect and
posix_cpu_timers_work will never run (not to mention it doesn't make sense
for two tasks to share a common linked list).
Since posix_cpu_timers_work never runs, posix_cputimers_work.scheduled is
never cleared. Since scheduled is set, future timer interrupts will skip
scheduling work, with the ultimate result that the task will never receive
timer expirations.
Together, the complete flow is:
1. Task 1 calls clone(), enters kernel.
2. Timer interrupt fires, schedules task work on Task 1.
2a. task_struct.posix_cputimers_work.scheduled = true
2b. task_struct.posix_cputimers_work.work added to
task_struct.task_works.
3. dup_task_struct() copies Task 1 to Task 2.
4. copy_process() clears task_struct.task_works for Task 2.
5. Future timer interrupts on Task 2 see
task_struct.posix_cputimers_work.scheduled = true and skip scheduling
work.
Fix this by explicitly clearing contents of task_struct.posix_cputimers_work
in copy_process(). This was never meant to be shared or inherited across
tasks in the first place.
Fixes: 1fb497dd00 ("posix-cpu-timers: Provide mechanisms to defer timer handling to task_work")
Reported-by: Rhys Hiltner <rhys@justin.tv>
Signed-off-by: Michael Pratt <mpratt@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211101210615.716522-1-mpratt@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a923a2676e upstream.
Fix assembly errors like:
{standard input}: Assembler messages:
{standard input}:287: Error: opcode not supported on this processor: mips3 (mips3) `dins $10,$7,32,32'
{standard input}:680: Error: opcode not supported on this processor: mips3 (mips3) `dins $10,$7,32,32'
{standard input}:1274: Error: opcode not supported on this processor: mips3 (mips3) `dins $12,$9,32,32'
{standard input}:2175: Error: opcode not supported on this processor: mips3 (mips3) `dins $10,$7,32,32'
make[1]: *** [scripts/Makefile.build:277: mm/highmem.o] Error 1
with code produced from `__cmpxchg64' for MIPS64r2 CPU configurations
using CONFIG_32BIT and CONFIG_PHYS_ADDR_T_64BIT.
This is due to MIPS_ISA_ARCH_LEVEL downgrading the assembly architecture
to `r4000' i.e. MIPS III for MIPS64r2 configurations, while there is a
block of code containing a DINS MIPS64r2 instruction conditionalized on
MIPS_ISA_REV >= 2 within the scope of the downgrade.
The assembly architecture override code pattern has been put there for
LL/SC instructions, so that code compiles for configurations that select
a processor to build for that does not support these instructions while
still providing run-time support for processors that do, dynamically
switched by non-constant `cpu_has_llsc'. It went in with linux-mips.org
commit aac8aa7717 ("Enable a suitable ISA for the assembler around
ll/sc so that code builds even for processors that don't support the
instructions. Plus minor formatting fixes.") back in 2005.
Fix the problem by wrapping these instructions along with the adjacent
SYNC instructions only, following the practice established with commit
cfd54de3b0 ("MIPS: Avoid move psuedo-instruction whilst using
MIPS_ISA_LEVEL") and commit 378ed6f0e3 ("MIPS: Avoid using .set mips0
to restore ISA"). Strictly speaking the SYNC instructions do not have
to be wrapped as they are only used as a Loongson3 erratum workaround,
so they will be enabled in the assembler by default, but do this so as
to keep code consistent with other places.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: c7e2d71dda ("MIPS: Fix set_pte() for Netlogic XLR using cmpxchg64()")
Cc: stable@vger.kernel.org # v5.1+
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 279917e27e upstream.
I noticed that sometimes at kernel startup the backtraces did not
included the function names of init functions. Their address were not
resolved to function names and instead only the address was printed.
Debugging shows that the culprit is is_ksym_addr() which is called
by the backtrace functions to check if an address belongs to a function in
the kernel. The problem occurs only for CONFIG_KALLSYMS_ALL=y.
When looking at is_ksym_addr() one can see that for CONFIG_KALLSYMS_ALL=y
the function only tries to resolve the address via is_kernel() function,
which checks like this:
if (addr >= _stext && addr <= _end)
return 1;
On parisc the init functions are located before _stext, so this check fails.
Other platforms seem to have all functions (including init functions)
behind _stext.
The following patch moves the _stext symbol at the beginning of the
kernel and thus includes the init section. This fixes the check and does
not seem to have any negative side effects on where the kernel mapping
happens in the map_pages() function in arch/parisc/mm/init.c.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@kernel.org # 5.4+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 418ace9992 upstream.
Naresh and Antonio ran into a build failure with latest Debian
armhf compilers, with lots of output like
tmp/ccY3nOAs.s:2215: Error: selected processor does not support `cpsid i' in ARM mode
As it turns out, $(cc-option) fails early here when the FPU is not
selected before CPU architecture is selected, as the compiler
option check runs before enabling -msoft-float, which causes
a problem when testing a target architecture level without an FPU:
cc1: error: '-mfloat-abi=hard': selected architecture lacks an FPU
Passing e.g. -march=armv6k+fp in place of -march=armv6k would avoid this
issue, but the fallback logic is already broken because all supported
compilers (gcc-5 and higher) are much more recent than these options,
and building with -march=armv5t as a fallback no longer works.
The best way forward that I see is to just remove all the checks, which
also has the nice side-effect of slightly improving the startup time for
'make'.
The -mtune=marvell-f option was apparently never supported by any mainline
compiler, and the custom Codesourcery gcc build that did support is
now too old to build kernels, so just use -mtune=xscale unconditionally
for those.
This should be safe to apply on all stable kernels, and will be required
in order to keep building them with gcc-11 and higher.
Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=996419
Reported-by: Antonio Terceiro <antonio.terceiro@linaro.org>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Reported-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Cc: Matthias Klose <doko@debian.org>
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d08e7bf0d upstream.
Currently __set_fixmap() bails out with a warning when called in early boot
from early_iounmap(). Fix it, and while at it, make the comment a bit easier
to understand.
Cc: <stable@vger.kernel.org>
Fixes: b089c31c51 ("ARM: 8667/3: Fix memory attribute inconsistencies when using fixmap")
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d336509cb9 ]
The below commit added optional support for passing a bind address.
It configures the sockaddr bind arguments before parsing options and
reconfigures on options -b and -4.
This broke support for passing port (-p) on its own.
Configure sockaddr after parsing all arguments.
Fixes: 3327a9c463 ("selftests: add functionals test for UDP GRO")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ca110bf8d ]
Ensure diagnostics monitoring support is implemented for the SFF 8472
compliant port module and set the correct length for ethtool port
module eeprom read.
Fixes: f56ec6766d ("cxgb4: Add support for ethtool i2c dump")
Signed-off-by: Manoj Malviya <manojmalviya@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5d5aadcf3 ]
We got the following WARNING when running ab/nginx
test with RDMA link flapping (up-down-up).
The reason is when smc_sock fallback and at linkdown
happens simultaneously, we may got the following situation:
__smc_lgr_terminate()
--> smc_conn_kill()
--> smc_close_active_abort()
smc_sock->sk_state = SMC_CLOSED
sock_put(smc_sock)
smc_sock was set to SMC_CLOSED and sock_put() been called
when terminate the link group. But later application call
close() on the socket, then we got:
__smc_release():
if (smc_sock->fallback)
smc_sock->sk_state = SMC_CLOSED
sock_put(smc_sock)
Again we set the smc_sock to CLOSED through it's already
in CLOSED state, and double put the refcnt, so the following
warning happens:
refcount_t: underflow; use-after-free.
WARNING: CPU: 5 PID: 860 at lib/refcount.c:28 refcount_warn_saturate+0x8d/0xf0
Modules linked in:
CPU: 5 PID: 860 Comm: nginx Not tainted 5.10.46+ #403
Hardware name: Alibaba Cloud Alibaba Cloud ECS, BIOS 8c24b4c 04/01/2014
RIP: 0010:refcount_warn_saturate+0x8d/0xf0
Code: 05 5c 1e b5 01 01 e8 52 25 bc ff 0f 0b c3 80 3d 4f 1e b5 01 00 75 ad 48
RSP: 0018:ffffc90000527e50 EFLAGS: 00010286
RAX: 0000000000000026 RBX: ffff8881300df2c0 RCX: 0000000000000027
RDX: 0000000000000000 RSI: ffff88813bd58040 RDI: ffff88813bd58048
RBP: 0000000000000000 R08: 0000000000000003 R09: 0000000000000001
R10: ffff8881300df2c0 R11: ffffc90000527c78 R12: ffff8881300df340
R13: ffff8881300df930 R14: ffff88810b3dad80 R15: ffff8881300df4f8
FS: 00007f739de8fb80(0000) GS:ffff88813bd40000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000000a01b008 CR3: 0000000111b64003 CR4: 00000000003706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
smc_release+0x353/0x3f0
__sock_release+0x3d/0xb0
sock_close+0x11/0x20
__fput+0x93/0x230
task_work_run+0x65/0xa0
exit_to_user_mode_prepare+0xf9/0x100
syscall_exit_to_user_mode+0x27/0x190
entry_SYSCALL_64_after_hwframe+0x44/0xa9
This patch adds check in __smc_release() to make
sure we won't do an extra sock_put() and set the
socket to CLOSED when its already in CLOSED state.
Fixes: 51f1de79ad (net/smc: replace sock_put worker by socket refcounting)
Signed-off-by: Dust Li <dust.li@linux.alibaba.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: Dust Li <dust.li@linux.alibaba.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7cd82b905 ]
Currently vosck_connect() increments sock refcount for nonblocking
socket each time it's called, which can lead to memory leak if
it's called multiple times because connect timeout function decrements
sock refcount only once.
Fixes it by making vsock_connect() return -EALREADY immediately when
sock state is already SS_CONNECTING.
Fixes: d021c34405 ("VSOCK: Introduce VM Sockets")
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Eiichi Tsukata <eiichi.tsukata@nutanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f64ab8e4f3 ]
Commit fe28c53ed7 ("net: stmmac: fix taprio configuration when
base_time is in the past") allowed some base time values in the past,
but apparently not all, the base-time value of 0 (Jan 1st 1970) is still
explicitly denied by the driver.
Remove the bogus check.
Fixes: b60189e039 ("net: stmmac: Integrate EST with TAPRIO scheduler API")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 688db0c7a4 ]
Currently, driver only allow configuring ETS bandwidth of TCs according
to the max TC number queried from firmware. However, the hardware actually
supports 8 TCs and users may need to configure ETS bandwidth of all TCs,
so remove the restriction.
Fixes: 330baff542 ("net: hns3: add ETS TC weight setting in SSU module")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c360cc1cc ]
The priv->ntfy_blocks[] has "priv->num_ntfy_blks" elements so this >
needs to be >= to prevent an off by one bug. The priv->ntfy_blocks[]
array is allocated in gve_alloc_notify_blocks().
Fixes: 87a7f321bb ("gve: Recover from queue stall due to missed IRQ")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0dc3b93bd ]
Strparser is reusing the qdisc_skb_cb struct to stash the skb message handling
progress, e.g. offset and length of the skb. First this is poorly named and
inherits a struct from qdisc that doesn't reflect the actual usage of cb[] at
this layer.
But, more importantly strparser is using the following to access its metadata.
(struct _strp_msg *)((void *)skb->cb + offsetof(struct qdisc_skb_cb, data))
Where _strp_msg is defined as:
struct _strp_msg {
struct strp_msg strp; /* 0 8 */
int accum_len; /* 8 4 */
/* size: 12, cachelines: 1, members: 2 */
/* last cacheline: 12 bytes */
};
So we use 12 bytes of ->data[] in struct. However in BPF code running parser
and verdict the user has read capabilities into the data[] array as well. Its
not too problematic, but we should not be exposing internal state to BPF
program. If its really needed then we can use the probe_read() APIs which allow
reading kernel memory. And I don't believe cb[] layer poses any API breakage by
moving this around because programs can't depend on cb[] across layers.
In order to fix another issue with a ctx rewrite we need to stash a temp
variable somewhere. To make this work cleanly this patch builds a cb struct
for sk_skb types called sk_skb_cb struct. Then we can use this consistently
in the strparser, sockmap space. Additionally we can start allowing ->cb[]
write access after this.
Fixes: 604326b41a ("bpf, sockmap: convert to generic sk_msg interface")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Jussi Maki <joamaki@gmail.com>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/20211103204736.248403-5-john.fastabend@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8b8315e39 ]
We do not need to handle unhash from BPF side we can simply wait for the
close to happen. The original concern was a socket could transition from
ESTABLISHED state to a new state while the BPF hook was still attached.
But, we convinced ourself this is no longer possible and we also improved
BPF sockmap to handle listen sockets so this is no longer a problem.
More importantly though there are cases where unhash is called when data is
in the receive queue. The BPF unhash logic will flush this data which is
wrong. To be correct it should keep the data in the receive queue and allow
a receiving application to continue reading the data. This may happen when
tcp_abort() is received for example. Instead of complicating the logic in
unhash simply moving all this to tcp_close() hook solves this.
Fixes: 51199405f9 ("bpf: skb_verdict, support SK_PASS on RX BPF path")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Jussi Maki <joamaki@gmail.com>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/20211103204736.248403-3-john.fastabend@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7c386fbc2 ]
gcc warns about undefined behavior the vmalloc code when building
with CONFIG_ARM64_PA_BITS_52, when the 'idx++' in the argument to
__phys_to_pte_val() is evaluated twice:
mm/vmalloc.c: In function 'vmap_pfn_apply':
mm/vmalloc.c:2800:58: error: operation on 'data->idx' may be undefined [-Werror=sequence-point]
2800 | *pte = pte_mkspecial(pfn_pte(data->pfns[data->idx++], data->prot));
| ~~~~~~~~~^~
arch/arm64/include/asm/pgtable-types.h:25:37: note: in definition of macro '__pte'
25 | #define __pte(x) ((pte_t) { (x) } )
| ^
arch/arm64/include/asm/pgtable.h:80:15: note: in expansion of macro '__phys_to_pte_val'
80 | __pte(__phys_to_pte_val((phys_addr_t)(pfn) << PAGE_SHIFT) | pgprot_val(prot))
| ^~~~~~~~~~~~~~~~~
mm/vmalloc.c:2800:30: note: in expansion of macro 'pfn_pte'
2800 | *pte = pte_mkspecial(pfn_pte(data->pfns[data->idx++], data->prot));
| ^~~~~~~
I have no idea why this never showed up earlier, but the safest
workaround appears to be changing those macros into inline functions
so the arguments get evaluated only once.
Cc: Matthew Wilcox <willy@infradead.org>
Fixes: 75387b9263 ("arm64: handle 52-bit physical addresses in page table entries")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211105075414.2553155-1-arnd@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9fec40f850 ]
skb is already freed by dev_kfree_skb in pn533_fill_fragment_skbs,
but follow error handler branch when pn533_fill_fragment_skbs()
fails, skb is freed again, results in double free issue. Fix this
by not free skb in error path of pn533_fill_fragment_skbs.
Fixes: 963a82e07d ("NFC: pn533: Split large Tx frames in chunks")
Fixes: 93ad42020c ("NFC: pn533: Target mode Tx fragmentation support")
Signed-off-by: Chengfeng Ye <cyeaa@connect.ust.hk>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ac9dfd58b ]
Both ifindex and LLC_SK_DEV_HASH_ENTRIES are signed.
This means that (ifindex % LLC_SK_DEV_HASH_ENTRIES) is negative
if @ifindex is negative.
We could simply make LLC_SK_DEV_HASH_ENTRIES unsigned.
In this patch I chose to use hash_32() to get more entropy
from @ifindex, like llc_sk_laddr_hashfn().
UBSAN: array-index-out-of-bounds in ./include/net/llc.h:75:26
index -43 is out of range for type 'hlist_head [64]'
CPU: 1 PID: 20999 Comm: syz-executor.3 Not tainted 5.15.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
ubsan_epilogue+0xb/0x5a lib/ubsan.c:151
__ubsan_handle_out_of_bounds.cold+0x62/0x6c lib/ubsan.c:291
llc_sk_dev_hash include/net/llc.h:75 [inline]
llc_sap_add_socket+0x49c/0x520 net/llc/llc_conn.c:697
llc_ui_bind+0x680/0xd70 net/llc/af_llc.c:404
__sys_bind+0x1e9/0x250 net/socket.c:1693
__do_sys_bind net/socket.c:1704 [inline]
__se_sys_bind net/socket.c:1702 [inline]
__x64_sys_bind+0x6f/0xb0 net/socket.c:1702
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7fa503407ae9
Fixes: 6d2e3ea284 ("llc: use a device based hash table to speed up multicast delivery")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit afe8605ca4 ]
There is one possible race window between zs_pool_dec_isolated() and
zs_unregister_migration() because wait_for_isolated_drain() checks the
isolated count without holding class->lock and there is no order inside
zs_pool_dec_isolated(). Thus the below race window could be possible:
zs_pool_dec_isolated zs_unregister_migration
check pool->destroying != 0
pool->destroying = true;
smp_mb();
wait_for_isolated_drain()
wait for pool->isolated_pages == 0
atomic_long_dec(&pool->isolated_pages);
atomic_long_read(&pool->isolated_pages) == 0
Since we observe the pool->destroying (false) before atomic_long_dec()
for pool->isolated_pages, waking pool->migration_wait up is missed.
Fix this by ensure checking pool->destroying happens after the
atomic_long_dec(&pool->isolated_pages).
Link: https://lkml.kernel.org/r/20210708115027.7557-1-linmiaohe@huawei.com
Fixes: 701d678599 ("mm/zsmalloc.c: fix race condition in zs_destroy_pool")
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Henry Burns <henryburns@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b93c6a911a ]
When I do fuzz test for bonding device interface, I got the following
use-after-free Calltrace:
==================================================================
BUG: KASAN: use-after-free in bond_enslave+0x1521/0x24f0
Read of size 8 at addr ffff88825bc11c00 by task ifenslave/7365
CPU: 5 PID: 7365 Comm: ifenslave Tainted: G E 5.15.0-rc1+ #13
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1 04/01/2014
Call Trace:
dump_stack_lvl+0x6c/0x8b
print_address_description.constprop.0+0x48/0x70
kasan_report.cold+0x82/0xdb
__asan_load8+0x69/0x90
bond_enslave+0x1521/0x24f0
bond_do_ioctl+0x3e0/0x450
dev_ifsioc+0x2ba/0x970
dev_ioctl+0x112/0x710
sock_do_ioctl+0x118/0x1b0
sock_ioctl+0x2e0/0x490
__x64_sys_ioctl+0x118/0x150
do_syscall_64+0x35/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f19159cf577
Code: b3 66 90 48 8b 05 11 89 2c 00 64 c7 00 26 00 00 00 48 c7 c0 ff ff ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 b8 10 00 00 00 0f 05 <48> 3d 01 f0 ff ff 78
RSP: 002b:00007ffeb3083c78 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 00007ffeb3084bca RCX: 00007f19159cf577
RDX: 00007ffeb3083ce0 RSI: 0000000000008990 RDI: 0000000000000003
RBP: 00007ffeb3084bc4 R08: 0000000000000040 R09: 0000000000000000
R10: 00007ffeb3084bc0 R11: 0000000000000246 R12: 00007ffeb3083ce0
R13: 0000000000000000 R14: 0000000000000000 R15: 00007ffeb3083cb0
Allocated by task 7365:
kasan_save_stack+0x23/0x50
__kasan_kmalloc+0x83/0xa0
kmem_cache_alloc_trace+0x22e/0x470
bond_enslave+0x2e1/0x24f0
bond_do_ioctl+0x3e0/0x450
dev_ifsioc+0x2ba/0x970
dev_ioctl+0x112/0x710
sock_do_ioctl+0x118/0x1b0
sock_ioctl+0x2e0/0x490
__x64_sys_ioctl+0x118/0x150
do_syscall_64+0x35/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
Freed by task 7365:
kasan_save_stack+0x23/0x50
kasan_set_track+0x20/0x30
kasan_set_free_info+0x24/0x40
__kasan_slab_free+0xf2/0x130
kfree+0xd1/0x5c0
slave_kobj_release+0x61/0x90
kobject_put+0x102/0x180
bond_sysfs_slave_add+0x7a/0xa0
bond_enslave+0x11b6/0x24f0
bond_do_ioctl+0x3e0/0x450
dev_ifsioc+0x2ba/0x970
dev_ioctl+0x112/0x710
sock_do_ioctl+0x118/0x1b0
sock_ioctl+0x2e0/0x490
__x64_sys_ioctl+0x118/0x150
do_syscall_64+0x35/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
Last potentially related work creation:
kasan_save_stack+0x23/0x50
kasan_record_aux_stack+0xb7/0xd0
insert_work+0x43/0x190
__queue_work+0x2e3/0x970
delayed_work_timer_fn+0x3e/0x50
call_timer_fn+0x148/0x470
run_timer_softirq+0x8a8/0xc50
__do_softirq+0x107/0x55f
Second to last potentially related work creation:
kasan_save_stack+0x23/0x50
kasan_record_aux_stack+0xb7/0xd0
insert_work+0x43/0x190
__queue_work+0x2e3/0x970
__queue_delayed_work+0x130/0x180
queue_delayed_work_on+0xa7/0xb0
bond_enslave+0xe25/0x24f0
bond_do_ioctl+0x3e0/0x450
dev_ifsioc+0x2ba/0x970
dev_ioctl+0x112/0x710
sock_do_ioctl+0x118/0x1b0
sock_ioctl+0x2e0/0x490
__x64_sys_ioctl+0x118/0x150
do_syscall_64+0x35/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
The buggy address belongs to the object at ffff88825bc11c00
which belongs to the cache kmalloc-1k of size 1024
The buggy address is located 0 bytes inside of
1024-byte region [ffff88825bc11c00, ffff88825bc12000)
The buggy address belongs to the page:
page:ffffea00096f0400 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x25bc10
head:ffffea00096f0400 order:3 compound_mapcount:0 compound_pincount:0
flags: 0x57ff00000010200(slab|head|node=1|zone=2|lastcpupid=0x7ff)
raw: 057ff00000010200 ffffea0009a71c08 ffff888240001968 ffff88810004dbc0
raw: 0000000000000000 00000000000a000a 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff88825bc11b00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff88825bc11b80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff88825bc11c00: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff88825bc11c80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff88825bc11d00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================
Put new_slave in bond_sysfs_slave_add() will cause use-after-free problems
when new_slave is accessed in the subsequent error handling process. Since
new_slave will be put in the subsequent error handling process, remove the
unnecessary put to fix it.
In addition, when sysfs_create_file() fails, if some files have been crea-
ted successfully, we need to call sysfs_remove_file() to remove them.
Since there are sysfs_create_files() & sysfs_remove_files() can be used,
use these two functions instead.
Fixes: 7afcaec496 (bonding: use kobject_put instead of _del after kobject_add)
Signed-off-by: Huang Guobin <huangguobin4@huawei.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 009a789443 ]
The handling of PMIC register reads through writing 0 to address 4
of the OpRegion is wrong. Instead of returning the read value
through the value64, which is a no-op for function == ACPI_WRITE calls,
store the value and then on a subsequent function == ACPI_READ with
address == 3 (the address for the value field of the OpRegion)
return the stored value.
This has been tested on a Xiaomi Mi Pad 2 and makes the ACPI battery dev
there mostly functional (unfortunately there are still other issues).
Here are the SET() / GET() functions of the PMIC ACPI device,
which use this OpRegion, which clearly show the new behavior to
be correct:
OperationRegion (REGS, 0x8F, Zero, 0x50)
Field (REGS, ByteAcc, NoLock, Preserve)
{
CLNT, 8,
SA, 8,
OFF, 8,
VAL, 8,
RWM, 8
}
Method (GET, 3, Serialized)
{
If ((AVBE == One))
{
CLNT = Arg0
SA = Arg1
OFF = Arg2
RWM = Zero
If ((AVBG == One))
{
GPRW = Zero
}
}
Return (VAL) /* \_SB_.PCI0.I2C7.PMI5.VAL_ */
}
Method (SET, 4, Serialized)
{
If ((AVBE == One))
{
CLNT = Arg0
SA = Arg1
OFF = Arg2
VAL = Arg3
RWM = One
If ((AVBG == One))
{
GPRW = One
}
}
}
Fixes: 0afa877a56 ("ACPI / PMIC: intel: add REGS operation region support")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b385cca473 ]
When a VF is removed and/or reset its Tx queues need to be
stopped from the PF. This is done by calling the ice_dis_vf_qs()
function, which calls ice_vsi_stop_lan_tx_rings(). Currently
ice_dis_vf_qs() is protected by the VF state bit ICE_VF_STATE_QS_ENA.
Unfortunately, this is causing the Tx queues to not be disabled in some
cases and when the VF tries to re-enable/reconfigure its Tx queues over
virtchnl the op is failing. This is because a VF can be reset and/or
removed before the ICE_VF_STATE_QS_ENA bit is set, but the Tx queues
were already configured via ice_vsi_cfg_single_txq() in the
VIRTCHNL_OP_CONFIG_VSI_QUEUES op. However, the ICE_VF_STATE_QS_ENA bit
is set on a successful VIRTCHNL_OP_ENABLE_QUEUES, which will always
happen after the VIRTCHNL_OP_CONFIG_VSI_QUEUES op.
This was causing the following error message when loading the ice
driver, creating VFs, and modifying VF trust in an endless loop:
[35274.192484] ice 0000:88:00.0: Failed to set LAN Tx queue context, error: ICE_ERR_PARAM
[35274.193074] ice 0000:88:00.0: VF 0 failed opcode 6, retval: -5
[35274.193640] iavf 0000:88:01.0: PF returned error -5 (IAVF_ERR_PARAM) to our request 6
Fix this by always calling ice_dis_vf_qs() and silencing the error
message in ice_vsi_stop_tx_ring() since the calling code ignores the
return anyway. Also, all other places that call ice_vsi_stop_tx_ring()
catch the error, so this doesn't affect those flows since there was no
change to the values the function returns.
Other solutions were considered (i.e. tracking which VF queues had been
"started/configured" in VIRTCHNL_OP_CONFIG_VSI_QUEUES, but it seemed
more complicated than it was worth. This solution also brings in the
chance for other unexpected conditions due to invalid state bit checks.
So, the proposed solution seemed like the best option since there is no
harm in failing to stop Tx queues that were never started.
This issue can be seen using the following commands:
for i in {0..50}; do
rmmod ice
modprobe ice
sleep 1
echo 1 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 1 > /sys/class/net/ens785f1/device/sriov_numvfs
ip link set ens785f1 vf 0 trust on
ip link set ens785f0 vf 0 trust on
sleep 2
echo 0 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 0 > /sys/class/net/ens785f1/device/sriov_numvfs
sleep 1
echo 1 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 1 > /sys/class/net/ens785f1/device/sriov_numvfs
ip link set ens785f1 vf 0 trust on
ip link set ens785f0 vf 0 trust on
done
Fixes: 77ca27c417 ("ice: add support for virtchnl_queue_select.[tx|rx]_queues bitmap")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce572a5b88 ]
VF was not able to change its hardware MAC address in case
the new address was already present in the MAC filter list.
Change the handling of VF add mac request to not return
if requested MAC address is already present on the list
and check if its hardware MAC needs to be updated in this case.
Fixes: ed4c068d46 ("ice: Enable ip link show on the PF to display VF unicast MAC(s)")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 563bcbae3b ]
The real_dev of a vlan net_device may be freed after
unregister_vlan_dev(). Access the real_dev continually by
vlan_dev_real_dev() will trigger the UAF problem for the
real_dev like following:
==================================================================
BUG: KASAN: use-after-free in vlan_dev_real_dev+0xf9/0x120
Call Trace:
kasan_report.cold+0x83/0xdf
vlan_dev_real_dev+0xf9/0x120
is_eth_port_of_netdev_filter.part.0+0xb1/0x2c0
is_eth_port_of_netdev_filter+0x28/0x40
ib_enum_roce_netdev+0x1a3/0x300
ib_enum_all_roce_netdevs+0xc7/0x140
netdevice_event_work_handler+0x9d/0x210
...
Freed by task 9288:
kasan_save_stack+0x1b/0x40
kasan_set_track+0x1c/0x30
kasan_set_free_info+0x20/0x30
__kasan_slab_free+0xfc/0x130
slab_free_freelist_hook+0xdd/0x240
kfree+0xe4/0x690
kvfree+0x42/0x50
device_release+0x9f/0x240
kobject_put+0x1c8/0x530
put_device+0x1b/0x30
free_netdev+0x370/0x540
ppp_destroy_interface+0x313/0x3d0
...
Move the put_device(real_dev) to vlan_dev_free(). Ensure
real_dev not be freed before vlan_dev unregistered.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: syzbot+e4df4e1389e28972e955@syzkaller.appspotmail.com
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27dff9a9c2 ]
Throughout the OpenRISC kernel port VMA is passed as NULL when flushing
kernel tlb entries. Somehow this was missed when I was testing
c28b27416d ("openrisc: Implement proper SMP tlb flushing") and now the
SMP kernel fails to completely boot.
In OpenRISC VMA is used only to determine which cores need to have their
TLB entries flushed.
This patch updates the logic to flush tlbs on all cores when the VMA is
passed as NULL. Also, we update places VMA is passed as NULL to use
flush_tlb_kernel_range instead. Now, the only place VMA is passed as
NULL is in the implementation of flush_tlb_kernel_range.
Fixes: c28b27416d ("openrisc: Implement proper SMP tlb flushing")
Reported-by: Jan Henrik Weinstock <jan.weinstock@rwth-aachen.de>
Signed-off-by: Stafford Horne <shorne@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1aabe578dd ]
ETHTOOL_A_PAUSE_STAT_MAX is the MAX attribute id,
so we need to subtract non-stats and add one to
get a count (IOW -2+1 == -1).
Otherwise we'll see:
ethnl cmd 21: calculated reply length 40, but consumed 52
Fixes: 9a27a33027 ("ethtool: add standard pause stats")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d52bcb47bd ]
This patch allows to use 0 for `coal->rx_coalesce_usecs` param to
disable rx irq coalescing.
Previously we could enable rx irq coalescing via ethtool
(For ex: `ethtool -C eth0 rx-usecs 2000`) but we couldn't disable
it because this part rejects 0 value:
if (!coal->rx_coalesce_usecs)
return -EINVAL;
Fixes: 84da2658a6 ("TI DaVinci EMAC : Implement interrupt pacing functionality.")
Signed-off-by: Maxim Kiselev <bigunclemax@gmail.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20211101152343.4193233-1-bigunclemax@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f98960c04 ]
A successful 'clk_prepare()' call should be balanced by a corresponding
'clk_unprepare()' call in the error handling path of the probe, as already
done in the remove function.
More specifically, 'clk_prepare_enable()' is used, but 'clk_disable()' is
also already called. So just the unprepare step has still to be done.
Update the error handling path accordingly.
Fixes: 75d31c2372 ("i2c: xlr: add support for Sigma Designs controller variant")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 01d29f87fc ]
If we already hold open state on the client, yet the server gives us a
completely different stateid to the one we already hold, then we
currently treat it as if it were an out-of-sequence update, and wait for
5 seconds for other updates to come in.
This commit fixes the behaviour so that we immediately start processing
of the new stateid, and then leave it to the call to
nfs4_test_and_free_stateid() to decide what to do with the old stateid.
Fixes: b4868b44c5 ("NFSv4: Wait for stateid updates after CLOSE/OPEN_DOWNGRADE")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28b7ee33a2 ]
TI AR7 Watchdog Timer is only build for 32bit.
Avoid error like:
In file included from drivers/watchdog/ar7_wdt.c:29:
./arch/mips/include/asm/mach-ar7/ar7.h: In function ‘ar7_is_titan’:
./arch/mips/include/asm/mach-ar7/ar7.h:111:24: error: implicit declaration of function ‘KSEG1ADDR’; did you mean ‘CKSEG1ADDR’? [-Werror=implicit-function-declaration]
111 | return (readl((void *)KSEG1ADDR(AR7_REGS_GPIO + 0x24)) & 0xffff) ==
| ^~~~~~~~~
| CKSEG1ADDR
Fixes: da2a68b3eb ("watchdog: Enable COMPILE_TEST where possible")
Signed-off-by: Jackie Liu <liuyun01@kylinos.cn>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210907024904.4127611-1-liu.yun@linux.dev
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1aaa557b2d ]
'make randconfig' can produce a .config file with
"CONFIG_MEMORY_RESERVE=" (no value) since it has no default.
When a subsequent 'make all' is done, kconfig restarts the config
and prompts for a value for MEMORY_RESERVE. This breaks
scripting/automation where there is no interactive user input.
Add a default value for MEMORY_RESERVE. (Any integer value will
work here for kconfig.)
Fixes a kconfig warning:
.config:214:warning: symbol value '' invalid for MEMORY_RESERVE
* Restart config...
Memory reservation (MiB) (MEMORY_RESERVE) [] (NEW)
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2") # from beginning of git history
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: linux-m68k@lists.linux-m68k.org
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce0ee4e6ac ]
Today the sh code allocates memory the first time a process uses
the fpu. If that memory allocation fails, kill the affected task
with force_sig(SIGKILL) rather than do_group_exit(SIGKILL).
Calling do_group_exit from an exception handler can potentially lead
to dead locks as do_group_exit is not designed to be called from
interrupt context. Instead use force_sig(SIGKILL) to kill the
userspace process. Sending signals in general and force_sig in
particular has been tested from interrupt context so there should be
no problems.
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: linux-sh@vger.kernel.org
Fixes: 0ea820cf9b ("sh: Move over to dynamically allocated FPU context.")
Link: https://lkml.kernel.org/r/20211020174406.17889-6-ebiederm@xmission.com
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e7e1e880b1 ]
Before the `callback_result` callback was introduced drivers coded their
invocation to the callback in a similar way to:
if (cb->callback) {
spin_unlock(&dma->lock);
cb->callback(cb->callback_param);
spin_lock(&dma->lock);
}
With the introduction of `callback_result` two helpers where introduced to
transparently handle both types of callbacks. And drivers where updated to
look like this:
if (dmaengine_desc_callback_valid(cb)) {
spin_unlock(&dma->lock);
dmaengine_desc_callback_invoke(cb, ...);
spin_lock(&dma->lock);
}
dmaengine_desc_callback_invoke() correctly handles both `callback_result`
and `callback`. But we forgot to update the dmaengine_desc_callback_valid()
function to check for `callback_result`. As a result DMA descriptors that
use the `callback_result` rather than `callback` don't have their callback
invoked by drivers that follow the pattern above.
Fix this by checking for both `callback` and `callback_result` in
dmaengine_desc_callback_valid().
Fixes: f067025bc6 ("dmaengine: add support to provide error result from a DMA transation")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20211023134101.28042-1-lars@metafoo.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5648b5e116 ]
On 64bit platforms the MAC header is set to 0xffff on allocation and
also when a helper like skb_unset_mac_header() is called.
dev_parse_header may call skb_mac_header() which assumes valid mac offset:
BUG: KASAN: use-after-free in eth_header_parse+0x75/0x90
Read of size 6 at addr ffff8881075a5c05 by task nf-queue/1364
Call Trace:
memcpy+0x20/0x60
eth_header_parse+0x75/0x90
__nfqnl_enqueue_packet+0x1a61/0x3380
__nf_queue+0x597/0x1300
nf_queue+0xf/0x40
nf_hook_slow+0xed/0x190
nf_hook+0x184/0x440
ip_output+0x1c0/0x2a0
nf_reinject+0x26f/0x700
nfqnl_recv_verdict+0xa16/0x18b0
nfnetlink_rcv_msg+0x506/0xe70
The existing code only works if the skb has a mac header.
Fixes: 2c38de4c1f ("netfilter: fix looped (broad|multi)cast's MAC handling")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8120bd469f ]
Free the kbuf buffer before returning from the dpaa2_console_read()
function. The variable no longer goes out of scope, leaking the storage
it points to.
Fixes: c93349d8c1 ("soc: fsl: add DPAA2 console support")
Signed-off-by: Robert-Ionut Alexa <robert-ionut.alexa@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 840fe25833 ]
As the ht16k33 frame buffer sub-driver does not register an
fb_ops.fb_blank() handler, blanking does not work:
$ echo 1 > /sys/class/graphics/fb0/blank
sh: write error: Invalid argument
Fix this by providing a handler that always returns zero, to make sure
blank events will be sent to the actual device handling the backlight.
Reported-by: Robin van der Gracht <robin@protonic.nl>
Suggested-by: Robin van der Gracht <robin@protonic.nl>
Fixes: 8992da44c6 ("auxdisplay: ht16k33: Driver for LED controller")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 80f9eb70fd ]
Currently /sys/class/graphics/fb0/bl_curve is not accessible (-ENODEV),
as the driver does not connect the backlight to the frame buffer device.
Fix this moving backlight initialization up, and filling in
fb_info.bl_dev.
Fixes: 8992da44c6 ("auxdisplay: ht16k33: Driver for LED controller")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit afcb5a811f ]
While writing an empty string to a device attribute is a no-op, and thus
does not need explicit safeguards, the user can still write a single
newline to an attribute file:
echo > .../message
If that happens, img_ascii_lcd_display() trims the newline, yielding an
empty string, and causing an infinite loop in img_ascii_lcd_scroll().
Fix this by adding a check for empty strings. Clear the display in case
one is encountered.
Fixes: 0cad855fbd ("auxdisplay: img-ascii-lcd: driver for simple ASCII LCD displays")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 133a48abf6 ]
If O_DIRECT bumps the commit_info rpcs_out field, then that could lead
to fsync() hangs. The fix is to ensure that O_DIRECT calls
nfs_commit_end().
Fixes: 723c921e7d ("sched/wait, fs/nfs: Convert wait_on_atomic_t() usage to the new wait_var_event() API")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4caab28a62 ]
The condition register PCI_RCV_INTX is used in irq_mask() and irq_unmask()
callbacks. Accesses to register can occur at the same time without a lock.
Add a lock into each callback to prevent the issue.
And INTX mask and unmask fields in PCL_RCV_INTX register should only be
set/reset for each bit. Clearing by PCL_RCV_INTX_ALL_MASK should be
removed.
INTX status fields in PCL_RCV_INTX register only indicates each INTX
interrupt status, so the handler can't clear by writing 1 to the field.
The status is expected to be cleared by the interrupt origin.
The ack function has no meaning, so should remove it.
Suggested-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/1631924579-24567-1-git-send-email-hayashi.kunihiko@socionext.com
Fixes: 7e6d5cd88a ("PCI: uniphier: Add UniPhier PCIe host controller support")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Pali Rohár <pali@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78e4d34218 ]
hisi_spi_nor_probe() invokes clk_disable_unprepare() on all paths after
successful call of clk_prepare_enable(). Besides, the clock is enabled by
hispi_spi_nor_prep() and disabled by hispi_spi_nor_unprep(). So at remove
time it is not possible to have the clock enabled. The patch removes
excessive clk_disable_unprepare() from hisi_spi_nor_remove().
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: e523f11141 ("mtd: spi-nor: add hisilicon spi-nor flash controller driver")
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20210709144529.31379-1-novikov@ispras.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c2b46c824 ]
When op_alloc() returns NULL to new_op, no error return code of
orangefs_revalidate_lookup() is assigned.
To fix this bug, ret is assigned with -ENOMEM in this case.
Fixes: 8bb8aefd5a ("OrangeFS: Change almost all instances of the string PVFS2 to OrangeFS.")
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64a93dbf25 ]
Partially revert commit 2ce209c42c ("NFS: Wait for requests that are
locked on the commit list"), since it can lead to deadlocks between
commit requests and nfs_join_page_group().
For now we should assume that any locked requests on the commit list are
either about to be removed and committed by another task, or the writes
they describe are about to be retransmitted. In either case, we should
not need to worry.
Fixes: 2ce209c42c ("NFS: Wait for requests that are locked on the commit list")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27ff8187f1 ]
Fix sparse warning:
drivers/opp/of.c:924 _opp_add_static_v2() warn: passing zero to 'ERR_PTR'
For duplicate OPPs 'ret' be set to zero.
Fixes: deac8703da ("PM / OPP: _of_add_opp_table_v2(): increment count only if OPP is added")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d419052bc6 ]
Commit 43f5c77bcb ("PCI: aardvark: Fix reporting CRS value") started
using CRSSVE flag for handling CRS responses.
PCI_EXP_RTCTL_CRSSVE flag is stored only in emulated config space buffer
and there is handler for PCI_EXP_RTCTL register. So every read operation
from config space automatically clears CRSSVE flag as it is not defined in
PCI_EXP_RTCTL read handler.
Fix this by reading current CRSSVE bit flag from emulated space buffer and
appending it to PCI_EXP_RTCTL read response.
Link: https://lore.kernel.org/r/20211005180952.6812-5-kabel@kernel.org
Fixes: 43f5c77bcb ("PCI: aardvark: Fix reporting CRS value")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7be28bd73f ]
drivers/gpu/drm/drm_plane_helper.c: In function 'drm_primary_helper_update':
drivers/gpu/drm/drm_plane_helper.c:113:32: error: 'visible' is used uninitialized [-Werror=uninitialized]
113 | struct drm_plane_state plane_state = {
| ^~~~~~~~~~~
drivers/gpu/drm/drm_plane_helper.c:178:14: note: 'visible' was declared here
178 | bool visible;
| ^~~~~~~
cc1: all warnings being treated as errors
visible is an output, not an input. in practice this use might turn out
OK but it's still UB.
Fixes: df86af9133 ("drm/plane-helper: Add drm_plane_helper_check_state()")
Reviewed-by: Simon Ser <contact@emersion.fr>
Signed-off-by: Alex Xu (Hello71) <alex_y_xu@yahoo.ca>
Signed-off-by: Simon Ser <contact@emersion.fr>
Link: https://patchwork.freedesktop.org/patch/msgid/20211007063706.305984-1-alex_y_xu@yahoo.ca
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2915fa062 ]
_nfs4_pnfs_v3/v4_ds_connect do
some work
smp_wmb
ds->ds_clp = clp;
And nfs4_ff_layout_prepare_ds currently does
smp_rmb
if(ds->ds_clp)
...
This patch places the smp_rmb after the if. This ensures that following
reads only happen once nfs4_ff_layout_prepare_ds has checked that data
has been properly initialized.
Fixes: d67ae825a5 ("pnfs/flexfiles: Add the FlexFile Layout Driver")
Signed-off-by: Baptiste Lepers <baptiste.lepers@gmail.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cec08f452a ]
If the directory changed while we were revalidating the dentry, then
don't update the dentry verifier. There is no value in setting the
verifier to an older value, and we could end up overwriting a more up to
date verifier from a parallel revalidation.
Fixes: efeda80da3 ("NFSv4: Fix revalidation of dentries with delegations")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Tested-by: Benjamin Coddington <bcodding@redhat.com>
Reviewed-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8228aea5a ]
The reason for the modification here is that the previous
offset information is incorrect, OFFSET_DEBUGSTAT = 0xE4 is
the correct value.
Fixes: 25708278f8 ("i2c: mediatek: Add i2c support for MediaTek MT8183")
Signed-off-by: Kewei Xu <kewei.xu@mediatek.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b6e27d01a ]
Dan Carpenter says:
The patch d20c11d86d: "nfsd: Protect session creation and client
confirm using client_lock" from Jul 30, 2014, leads to the following
Smatch static checker warning:
net/sunrpc/addr.c:178 rpc_parse_scope_id()
warn: sleeping in atomic context
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: d20c11d86d ("nfsd: Protect session creation and client...")
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d108370c64 ]
clang static analysis reports this representative problem:
label.c:1463:16: warning: Assigned value is garbage or undefined
label->hname = name;
^ ~~~~
In aa_update_label_name(), this the problem block of code
if (aa_label_acntsxprint(&name, ...) == -1)
return res;
On failure, aa_label_acntsxprint() has a more complicated return
that just -1. So check for a negative return.
It was also noted that the aa_label_acntsxprint() main comment refers
to a nonexistent parameter, so clean up the comment.
Fixes: f1bd904175 ("apparmor: add the base fns() for domain labels")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: John Johansen <john.johansen@canonical.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdf10ffe8f ]
When registering the IRQ handler fails, do not just return the error code,
this will free the devm_kzalloc()-ed data struct while leaving the queued
work queued and the registered power_supply registered with both of them
now pointing to free-ed memory, resulting in various kernel crashes
soon afterwards.
Instead properly tear-down things on IRQ handler register errors.
Fixes: 703df6c097 ("power: bq27xxx_battery: Reorganize I2C into a module")
Cc: Andrew F. Davis <afd@ti.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 18b8f5b6fc ]
mips_cm_error_report() extracts the cause and other cause from the error
register using shifts. This works fine for the former, as it is stored
in the top bits, and the shift will thus remove all non-related bits.
However, the latter is stored in the bottom bits, hence thus needs masking
to get rid of non-related bits. Without such masking, using it as an
index into the cm2_causes[] array will lead to an out-of-bounds access,
probably causing a crash.
Fix this by using FIELD_GET() instead. Bite the bullet and convert all
MIPS CM handling to the bitfield API, to improve readability and safety.
Fixes: 3885c2b463 ("MIPS: CM: Add support for reporting CM cache errors")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 778a0cbef5 ]
The setting from the cirrus,ts-inv property should be applied to the
TIP_SENSE_INV bit, as this is the one that actually affects the jack
detect block. The TS_INV bit only swaps the meaning of the PLUG and
UNPLUG interrupts and should always be 1 for the interrupts to have
the normal meaning.
Due to some misunderstanding the driver had been implemented to
configure the TS_INV bit based on the jack switch polarity. This made
the interrupts behave the correct way around, but left the jack detect
block, button detect and analogue circuits always interpreting an open
switch as unplugged.
The signal chain inside the codec is:
SENSE pin -> TIP_SENSE_INV -> TS_INV -> (invert) -> interrupts
|
v
Jack detect,
button detect and
analog control
As the TIP_SENSE_INV already performs the necessary inversion the
TS_INV bit never needs to change. It must always be 1 to yield the
expected interrupt behaviour.
Some extra confusion has arisen because of the additional invert in the
interrupt path, meaning that a value applied to the TS_INV bit produces
the opposite effect of applying it to the TIP_SENSE_INV bit. The ts-inv
property has therefore always had the opposite effect to what might be
expected (0 = inverted, 1 = not inverted). To maintain the meaning of
the ts-inv property it must be inverted when applied to TIP_SENSE_INV.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2c394ca796 ("ASoC: Add support for CS42L42 codec")
Link: https://lore.kernel.org/r/20211028140902.11786-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43775e62c4 ]
The wait_for_completion_timeout function returns 0 if timed out or a
positive value if completed. Hence, "less than zero" comparison always
misses timeouts and doesn't kill the URB as it should, leading to
re-sending it while it is active.
Fixes: 42337b9d4d ("HID: add driver for U2F Zero built-in LED and RNG")
Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7abf78b7a ]
The previous commit fixed handling of incomplete packets but broke error
handling: offsetof returns an unsigned value (size_t), but when compared
against the signed return value, the return value is interpreted as if
it were unsigned, so negative return values are never less than the
offset.
To make the code easier to read, calculate the minimal packet length
once and separately, and assign it to a signed int variable to eliminate
unsigned math and the need for type casts. It then becomes immediately
obvious how the actual data length is calculated and why the return
value cannot be less than the minimal length.
Fixes: 22d65765f2 ("HID: u2fzero: ignore incomplete packets without data")
Fixes: 42337b9d4d ("HID: add driver for U2F Zero built-in LED and RNG")
Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 88b20f84f0 ]
xilinx_uartps .start_tx() clears TXEMPTY when enabling TXEMPTY to avoid
any previous TXEVENT event asserting the UART interrupt. This clear
operation is done immediately after filling the TX FIFO.
However, if the bytes inserted by cdns_uart_handle_tx() are consumed by
the UART before the TXEMPTY is cleared, the clear operation eats the new
TXEMPTY event as well, causing cdns_uart_isr() to never receive the
TXEMPTY event. If there are bytes still queued in circbuf, TX will get
stuck as they will never get transferred to FIFO (unless new bytes are
queued to circbuf in which case .start_tx() is called again).
While the racy missed TXEMPTY occurs fairly often with short data
sequences (e.g. write 1 byte), in those cases circbuf is usually empty
so no action on TXEMPTY would have been needed anyway. On the other
hand, longer data sequences make the race much more unlikely as UART
takes longer to consume the TX FIFO. Therefore it is rare for this race
to cause visible issues in general.
Fix the race by clearing the TXEMPTY bit in ISR *before* filling the
FIFO.
The TXEMPTY bit in ISR will only get asserted at the exact moment the
TX FIFO *becomes* empty, so clearing the bit before filling FIFO does
not cause an extra immediate assertion even if the FIFO is initially
empty.
This is hard to reproduce directly on a normal system, but inserting
e.g. udelay(200) after cdns_uart_handle_tx(port), setting 4000000 baud,
and then running "dd if=/dev/zero bs=128 of=/dev/ttyPS0 count=50"
reliably reproduces the issue on my ZynqMP test system unless this fix
is applied.
Fixes: 85baf542d5 ("tty: xuartps: support 64 byte FIFO size")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Link: https://lore.kernel.org/r/20211026102741.2910441-1-anssi.hannula@bitwise.fi
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b475bf0ec4 ]
The FSEL_MASK which selects the refclock is defined incorrectly.
It should be [4:6] not [5:7]. Due to this incorrect definition, the BIT(7)
in USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON0 is reset which keeps PHY analog
blocks ON during suspend.
Fix this issue by correctly defining the FSEL_MASK.
Fixes: 51e8114f80 ("phy: qcom-snps: Add SNPS USB PHY driver for QCOM based SOCs")
Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
Link: https://lore.kernel.org/r/1635135575-5668-1-git-send-email-quic_c_sanm@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d387f61b0 ]
In case of USB_DR_MODE_PERIPHERAL, the OTG clock is disabled at the end of
the probe (it is not the case if USB_DR_MODE_HOST or USB_DR_MODE_OTG).
The clock is then enabled on udc_start.
If dwc2_drd_role_sw_set is called before udc_start (it is the case if the
usb cable is plugged at boot), GOTGCTL and GUSBCFG registers cannot be
read/written, so session cannot be overridden.
To avoid this case, check the ll_hw_enabled value and enable the clock if
it is available, and disable it after the override.
Fixes: 17f934024e ("usb: dwc2: override PHY input signals with usb role switch support")
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211005095305.66397-3-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2cab2a24f ]
Instead of forcing the role to Device, check the dr_mode configuration.
If the core is Host only, force the mode to Host, this to avoid the
dwc2_force_mode warning:
WARNING: CPU: 1 PID: 21 at drivers/usb/dwc2/core.c:615 dwc2_drd_init+0x104/0x17c
When forcing mode to Host, dwc2_force_mode may sleep the time the host
role is applied. To avoid sleeping while atomic context, move the call
to dwc2_force_mode after spin_unlock_irqrestore. It is safe, as
interrupts are not yet unmasked here.
Fixes: 17f934024e ("usb: dwc2: override PHY input signals with usb role switch support")
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211005095305.66397-2-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b600bd7eb3 ]
With commit ecb010d441 ("iio: imu: adis: Refactor adis_initial_startup")
we are doing a HW or SW reset to the device which means that we'll get
the default state of the data ready pin (which is enabled). Hence there's
no point in disabling the IRQ in the init function. Moreover, this
function is intended to initialize internal data structures and not
really do anything on the device.
As a result of this, some devices were left with the data ready pin enabled
after probe which was not the desired behavior. Thus, we move the call to
'adis_enable_irq()' to the initial startup function where it makes more
sense for it to be.
Note that for devices that cannot mask/unmask the pin, it makes no sense
to call the function at this point since the IRQ should not have been
yet requested. This will be improved in a follow up change.
Fixes: ecb010d441 ("iio: imu: adis: Refactor adis_initial_startup")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210903141423.517028-2-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3e56c050a ]
The general expectation is that powering on a power-domain should make
the power domain deliver some power, and if a specific performance state
is needed further requests has to be made.
But in contrast with other power-domain implementations (e.g. rpmpd) the
RPMh does not have an interface to enable the power, so the driver has
to vote for a particular corner (performance level) in rpmh_power_on().
But the corner is never initialized, so a typical request to simply
enable the power domain would not actually turn on the hardware. Further
more, when no more clients vote for a performance state (i.e. the
aggregated vote is 0) the power domain would be turned off.
Fix both of these issues by always voting for a corner with non-zero
value, when the power domain is enabled.
The tracking of the lowest non-zero corner is performed to handle the
corner case if there's ever a domain with a non-zero lowest corner, in
which case both rpmh_power_on() and rpmh_rpmhpd_set_performance_state()
would be allowed to use this lowest corner.
Fixes: 279b7e8a62 ("soc: qcom: rpmhpd: Add RPMh power domain driver")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20211005033732.2284447-1-bjorn.andersson@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f87a74d31 ]
The STM32 SAI subblocks registers offsets are in the range
0x0004 (SAIx_CR1) to 0x0020 (SAIx_DR).
The corresponding range length is 0x20 instead of 0x1c.
Change reg property accordingly.
Fixes: 5afd65c3a0 ("ARM: dts: stm32: add sai support on stm32mp157c")
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2012579b31 ]
The SPI NOR is a bit further away from the SoC on DHCOR than on DHCOM,
which causes additional signal delay. At 108 MHz, this delay triggers
a sporadic issue where the first bit of RX data is not received by the
QSPI controller.
There are two options of addressing this problem, either by using the
DLYB block to compensate the extra delay, or by reducing the QSPI bus
clock frequency. The former requires calibration and that is overly
complex, so opt for the second option.
Fixes: 76045bc457 ("ARM: dts: stm32: Add QSPI NOR on AV96")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ab1891640 ]
Commit 723de0f917 ("staging: most: remove device from interface
structure") moved registration of driver-provided struct device to
the most subsystem.
Dim2 used to register the same struct device to provide a custom device
attribute. This causes double-registration of the same struct device.
Fix that by moving the custom attribute to driver's dev_groups.
This moves attribute to the platform_device object, which is a better
location for platform-specific attributes anyway.
Fixes: 723de0f917 ("staging: most: remove device from interface structure")
Acked-by: Christian Gromm <christian.gromm@microchip.com>
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Link: https://lore.kernel.org/r/20211011061117.21435-1-nikita.yoush@cogentembedded.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4875d509a ]
This variable is just a temporary variable, used to do an endian
conversion. The problem is that the last byte is not initialized. After
the conversion is completely done, the last byte is discarded so it doesn't
cause a problem. But static checkers and the KMSan runtime checker can
detect the uninitialized read and will complain about it.
Link: https://lore.kernel.org/r/20211006073242.GA8404@kili
Fixes: 5036f0a0ec ("[SCSI] csiostor: Fix sparse warnings.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9583922563 ]
Commit a21d1becaa ("powerpc: Reintroduce is_kvm_guest() as a fast-path
check") added is_kvm_guest() and changed kvm_para_available() to use it.
is_kvm_guest() checks a static key, kvm_guest, and that static key is
set in check_kvm_guest().
The problem is check_kvm_guest() is only called on pseries, and even
then only in some configurations. That means is_kvm_guest() always
returns false on all non-pseries and some pseries depending on
configuration. That's a bug.
For PR KVM guests this is noticable because they no longer do live
patching of themselves, which can be detected by the omission of a
message in dmesg such as:
KVM: Live patching for a fast VM worked
To fix it make check_kvm_guest() an initcall, to ensure it's always
called at boot. It needs to be core so that it runs before
kvm_guest_init() which is postcore. To be an initcall it needs to return
int, where 0 means success, so update that.
We still call it manually in pSeries_smp_probe(), because that runs
before init calls are run.
Fixes: a21d1becaa ("powerpc: Reintroduce is_kvm_guest() as a fast-path check")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210623130514.2543232-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2719b26ae ]
While investigating a lockup at startup on Powerbook 3400C, it was
identified that the fbdev driver generates alignment exception at
startup:
--- interrupt: 600 at memset+0x60/0xc0
NIP: c0021414 LR: c03fc49c CTR: 00007fff
REGS: ca021c10 TRAP: 0600 Tainted: G W (5.14.2-pmac-00727-g12a41fa69492)
MSR: 00009032 <EE,ME,IR,DR,RI> CR: 44008442 XER: 20000100
DAR: cab80020 DSISR: 00017c07
GPR00: 00000007 ca021cd0 c14412e0 cab80000 00000000 00100000 cab8001c 00000004
GPR08: 00100000 00007fff 00000000 00000000 84008442 00000000 c0006fb4 00000000
GPR16: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00100000
GPR24: 00000000 81800000 00000320 c15fa400 c14d1878 00000000 c14d1800 c094e19c
NIP [c0021414] memset+0x60/0xc0
LR [c03fc49c] chipsfb_pci_init+0x160/0x580
--- interrupt: 600
[ca021cd0] [c03fc46c] chipsfb_pci_init+0x130/0x580 (unreliable)
[ca021d20] [c03a3a70] pci_device_probe+0xf8/0x1b8
[ca021d50] [c043d584] really_probe.part.0+0xac/0x388
[ca021d70] [c043d914] __driver_probe_device+0xb4/0x170
[ca021d90] [c043da18] driver_probe_device+0x48/0x144
[ca021dc0] [c043e318] __driver_attach+0x11c/0x1c4
[ca021de0] [c043ad30] bus_for_each_dev+0x88/0xf0
[ca021e10] [c043c724] bus_add_driver+0x190/0x22c
[ca021e40] [c043ee94] driver_register+0x9c/0x170
[ca021e60] [c0006c28] do_one_initcall+0x54/0x1ec
[ca021ed0] [c08246e4] kernel_init_freeable+0x1c0/0x270
[ca021f10] [c0006fdc] kernel_init+0x28/0x11c
[ca021f30] [c0017148] ret_from_kernel_thread+0x14/0x1c
Instruction dump:
7d4601a4 39490777 7d4701a4 39490888 7d4801a4 39490999 7d4901a4 39290aaa
7d2a01a4 4c00012c 4bfffe88 0fe00000 <4bfffe80> 9421fff0 38210010 48001970
This is due to 'dcbz' instruction being used on non-cached memory.
'dcbz' instruction is used by memset() to zeroize a complete
cacheline at once, and memset() is not expected to be used on non
cached memory.
When performing a 'sparse' check on fbdev driver, it also appears
that the use of memset() is unexpected:
drivers/video/fbdev/chipsfb.c:334:17: warning: incorrect type in argument 1 (different address spaces)
drivers/video/fbdev/chipsfb.c:334:17: expected void *
drivers/video/fbdev/chipsfb.c:334:17: got char [noderef] __iomem *screen_base
drivers/video/fbdev/chipsfb.c:334:15: warning: memset with byte count of 1048576
Use fb_memset() instead of memset(). fb_memset() is defined as
memset_io() for powerpc.
Fixes: 8c8709334c ("[PATCH] ppc32: Remove CONFIG_PMAC_PBOOK")
Reported-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/884a54f1e5cb774c1d9b4db780209bee5d4f6718.1631712563.git.christophe.leroy@csgroup.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ed2f3545c ]
The error handling code of fsl_ifc_ctrl_probe is problematic. When
fsl_ifc_ctrl_init fails or request_irq of fsl_ifc_ctrl_dev->irq fails,
it forgets to free the irq and nand_irq. Meanwhile, if request_irq of
fsl_ifc_ctrl_dev->nand_irq fails, it will still free nand_irq even if
the request_irq is not successful.
Fix this by refactoring the error handling code.
Fixes: d2ae2e20fb ("driver/memory:Move Freescale IFC driver to a common driver")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Link: https://lore.kernel.org/r/20210925151434.8170-1-mudongliangabcd@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 986b509470 ]
If an error occurs after a successful tegra_powergate_enable_clocks()
call, it must be undone by a tegra_powergate_disable_clocks() call, as
already done in the below and above error handling paths of this function.
Update the 'goto' to branch at the correct place of the error handling
path.
Fixes: a38045121b ("soc/tegra: pmc: Add generic PM domain support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 884ea75d79 ]
Fix typo in pinctrl. It did only work because the bootloader
seems to have initialized it.
Fixes: ee32711195 ("ARM: dts: omap3-gta04: Define and use bma180 irq pin")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df0a181494 ]
I got memory leak as follows:
unreferenced object 0xffff88801f0b2200 (size 64):
comm "i2c-lis2hh12-21", pid 5455, jiffies 4294944606 (age 15.224s)
hex dump (first 32 bytes):
72 65 67 75 6c 61 74 6f 72 3a 72 65 67 75 6c 61 regulator:regula
74 6f 72 2e 30 2d 2d 69 32 63 3a 31 2d 30 30 31 tor.0--i2c:1-001
backtrace:
[<00000000bf5b0c3b>] __kmalloc_track_caller+0x19f/0x3a0
[<0000000050da42d9>] kvasprintf+0xb5/0x150
[<000000004bbbed13>] kvasprintf_const+0x60/0x190
[<00000000cdac7480>] kobject_set_name_vargs+0x56/0x150
[<00000000bf83f8e8>] dev_set_name+0xc0/0x100
[<00000000cc1cf7e3>] device_link_add+0x6b4/0x17c0
[<000000009db9faed>] _regulator_get+0x297/0x680
[<00000000845e7f2b>] _devm_regulator_get+0x5b/0xe0
[<000000003958ee25>] st_sensors_power_enable+0x71/0x1b0 [st_sensors]
[<000000005f450f52>] st_accel_i2c_probe+0xd9/0x150 [st_accel_i2c]
[<00000000b5f2ab33>] i2c_device_probe+0x4d8/0xbe0
[<0000000070fb977b>] really_probe+0x299/0xc30
[<0000000088e226ce>] __driver_probe_device+0x357/0x500
[<00000000c21dda32>] driver_probe_device+0x4e/0x140
[<000000004e650441>] __device_attach_driver+0x257/0x340
[<00000000cf1891b8>] bus_for_each_drv+0x166/0x1e0
When device_register() returns an error, the name allocated in dev_set_name()
will be leaked, the put_device() should be used instead of kfree() to give up
the device reference, then the name will be freed in kobject_cleanup() and the
references of consumer and supplier will be decreased in device_link_release_fn().
Fixes: 287905e68d ("driver core: Expose device link details in sysfs")
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Saravana Kannan <saravanak@google.com>
Reviewed-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210930085714.2057460-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4ca3871e2 ]
The commit f87e7f2589 ("ALSA: hda - Improved position reporting on
SKL+") changed the PCM position report for SKL+ chips to use DPIB, but
according to Pierre, DPIB is no best choice for the accurate position
reports and it often reports too early. The recommended method is
rather the classical position buffer.
This patch makes the PCM position reporting on SKL+ back to the
position buffer again.
Fixes: f87e7f2589 ("ALSA: hda - Improved position reporting on SKL+")
Suggested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210929072934.6809-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 472e18f63c ]
Make sure the HDA driver's display power reference is released during
shutdown/reboot.
During the shutdown/reboot sequence the pci device core calls the
pm_runtime_resume handler for all devices before calling the driver's
shutdown callback and so the HDA driver's runtime resume callback will
acquire a display power reference (on HSW/BDW). This triggers a power
reference held WARN on HSW/BDW in the i915 driver's subsequent shutdown
handler, which expects all display power references to be released by
that time.
Since the HDA controller is stopped in the shutdown handler in any case,
let's follow here the same sequence as the one during runtime suspend.
This will also reset the HDA link and drop the display power reference,
getting rid of the above WARN.
Tested on HSW.
v2:
- Fix the build for CONFIG_PM=n (Takashi)
- s/__azx_runtime_suspend/azx_shutdown_chip/
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/3618
References: https://lore.kernel.org/lkml/cea1f9a-52e0-b83-593d-52997fe1aaf6@er-systems.de
Reported-and-tested-by: Thomas Voegtle <tv@lio96.de>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://lore.kernel.org/r/20210623134601.2128663-1-imre.deak@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46243b85b0 ]
The position reporting on Intel Skylake and later chips via
azx_get_pos_skl() contains a udelay(20) call for the capture streams.
A call for this alone doesn't sound too harmful. However, as the
pointer PCM ops is one of the hottest path in the PCM operations --
especially for the timer-scheduled operations like PulseAudio -- such
a delay hogs CPU usage significantly in the total performance.
The code there was taken from the original code in ASoC SST Skylake
driver blindly. The udelay() is a workaround for the case where the
reported position is behind the period boundary at the timing
triggered from interrupts; applications often expect that the full
data is available for the whole period when returned (and also that's
the definition of the ALSA PCM period).
OTOH, HD-audio (legacy) driver has already some workarounds for the
delayed position reporting due to its relatively large FIFO, such as
the BDL position adjustment and the delayed period-elapsed call in the
work. That said, the udelay() is almost superfluous for HD-audio
driver unlike SST, and we can drop the udelay().
Though, the current code doesn't guarantee the full period readiness
as mentioned in the above, but rather it checks the wallclock and
detects the unexpected jump. That's one missing piece, and the drop
of udelay() needs a bit more sanity checks for the delayed handling.
This patch implements those: the drop of udelay() call in
azx_get_pos_skl() and the more proper check of hwptr in
azx_position_ok(). The latter change is applied only for the case
where the stream is running in the normal mode without
no_period_wakeup flag. When no_period_wakeup is set, it essentially
ignores the period handling and rather concentrates only on the
current position; which implies that we don't need to care about the
period boundary at all.
Fixes: f87e7f2589 ("ALSA: hda - Improved position reporting on SKL+")
Reported-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210929072934.6809-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 483de2b44c ]
While removing the size from the "reg" properties in pm8916.dtsi,
commit bd6429e810 ("ARM64: dts: qcom: Remove size elements from
pmic reg properties") mistakenly also removed the second register
address for the rtc@6000 device. That one did not represent the size
of the register region but actually the address of the second "alarm"
register region of the rtc@6000 device.
Now there are "reg-names" for two "reg" elements, but there is actually
only one "reg" listed.
Since the DT schema for "qcom,pm8941-rtc" only expects one "reg"
element anyway, just drop the "reg-names" entirely to fix this.
Fixes: bd6429e810 ("ARM64: dts: qcom: Remove size elements from pmic reg properties")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210928112945.25310-1-stephan@gerhold.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8199a0b31e ]
At the moment, playing audio on Secondary MI2S will just end up getting
stuck, without actually playing any audio. This happens because the wrong
bit clock is configured when playing audio on Secondary MI2S.
The PRI_I2S_CLK (better name: SPKR_I2S_CLK) is used by the SPKR audio mux
block that provides both Primary and Secondary MI2S.
The SEC_I2S_CLK (better name: MIC_I2S_CLK) is used by the MIC audio mux
block that provides Tertiary MI2S. Quaternary MI2S is also part of the
MIC audio mux but has its own clock (AUX_I2S_CLK).
This means that (quite confusingly) the SEC_I2S_CLK is not actually
used for Secondary MI2S as the name would suggest. Secondary MI2S
needs to have the same clock as Primary MI2S configured.
Fix the clock list for the lpass node in the device tree and add
a comment to clarify this confusing naming. With these changes,
audio can be played correctly on Secondary MI2S.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: 3761a3618f ("arm64: dts: qcom: add lpass node")
Tested-by: Vincent Knecht <vincent.knecht@mailoo.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210816181810.2242-1-stephan@gerhold.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c48a14dca2 ]
In jfs_mount, when diMount(ipaimap2) fails, it goes to errout35. However,
the following code does not free ipaimap2 allocated by diReadSpecial.
Fix this by refactoring the error handling code of jfs_mount. To be
specific, modify the lable name and free ipaimap2 when the above error
ocurrs.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f3b3c2bfa ]
mach/loongson64 fails to build when the FPU support is disabled:
arch/mips/loongson64/cop2-ex.c:45:15: error: implicit declaration of function ‘__is_fpu_owner’; did you mean ‘is_fpu_owner’? [-Werror=implicit-function-declaration]
arch/mips/loongson64/cop2-ex.c:98:30: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:99:30: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:131:43: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:137:38: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:203:30: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:219:30: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:283:38: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:301:38: error: ‘struct thread_struct’ has no member named ‘fpu’
Fixes: ef2f826c8f ("MIPS: Loongson-3: Enable the COP2 usage")
Suggested-by: Huacai Chen <chenhuacai@kernel.org>
Reviewed-by: Huacai Chen <chenhuacai@kernel.org>
Reported-by: k2ci robot <kernel-bot@kylinos.cn>
Signed-off-by: Jackie Liu <liuyun01@kylinos.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3e9431854 ]
On resume we can get a warning at kernel/time/timekeeping.c:824 for
timekeeping_suspended.
Let's fix this by adding separate functions for sysc_poll_reset_sysstatus()
and sysc_poll_reset_sysconfig() and have the new functions handle also
timekeeping_suspended.
If iopoll at some point supports timekeeping_suspended, we can just drop
the custom handling from these functions.
Fixes: d46f9fbec7 ("bus: ti-sysc: Use optional clocks on for enable and wait for softreset bit")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f46633565 ]
commit 4e5833884f ("arm64: dts: ti: k3-j721e-main: Add PCIe device
tree nodes") restricted PCIe bus numbers from 0 to 15 (due to SMMU
restriction in J721E). However since SMMU is not enabled, allow the full
supported bus numbers from 0 to 255.
Fixes: 4e5833884f ("arm64: dts: ti: k3-j721e-main: Add PCIe device tree nodes")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210915055358.19997-3-kishon@ti.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 932b4610f5 ]
As can be seen in RK3328's TRM the register range for the GPU is
0xff300000 to 0xff330000.
It would (and does in vendor kernel) overlap with the registers of
the HEVC encoder (node/driver do not exist yet in upstream kernel).
See already existing h265e_mmu node.
Fixes: 752fbc0c8d ("arm64: dts: rockchip: add rk3328 mali gpu node")
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20210623115926.164861-1-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f0b3e0cc0 ]
Up until commit ea7e586bdd ("iio: st_sensors: move regulator retrieveal
to core") only the ST pressure driver seems to have had any regulator
disable. After that commit, the regulator handling was moved into the
common st_sensors logic.
In all instances of this regulator handling, the regulators were disabled
before unregistering the IIO device.
This can cause issues where the device would be powered down and still be
available to userspace, allowing it to send invalid/garbage data.
This change moves the st_sensors_power_disable() after the common probe
functions. These common probe functions also handle unregistering the IIO
device.
Fixes: 774487611c ("iio: pressure-core: st: Provide support for the Vdd power supply")
Fixes: ea7e586bdd ("iio: st_sensors: move regulator retrieveal to core")
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Denis CIOCCA <denis.ciocca@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210823112204.243255-2-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b9979db834 ]
Before this fix:
166: (b5) if r2 <= 0x1 goto pc+22
from 166 to 189: R2=invP(id=1,umax_value=1,var_off=(0x0; 0xffffffff))
After this fix:
166: (b5) if r2 <= 0x1 goto pc+22
from 166 to 189: R2=invP(id=1,umax_value=1,var_off=(0x0; 0x1))
While processing BPF_JLE the reg_set_min_max() would set true_reg->umax_value = 1
and call __reg_combine_64_into_32(true_reg).
Without the fix it would not pass the condition:
if (__reg64_bound_u32(reg->umin_value) && __reg64_bound_u32(reg->umax_value))
since umin_value == 0 at this point.
Before commit 10bf4e8316 the umin was incorrectly ingored.
The commit 10bf4e8316 fixed the correctness issue, but pessimized
propagation of 64-bit min max into 32-bit min max and corresponding var_off.
Fixes: 10bf4e8316 ("bpf: Fix propagation of 32 bit unsigned bounds from 64 bit bounds")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20211101222153.78759-1-alexei.starovoitov@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 81c49d39ae ]
In account_guest_time in kernel/sched/cputime.c guest time is
attributed to both CPUTIME_NICE and CPUTIME_USER in addition to
CPUTIME_GUEST_NICE and CPUTIME_GUEST respectively. Therefore, adding
both to calculate usage results in double counting any guest time at
the rootcg.
Fixes: 936f2a70f2 ("cgroup: add cpu.stat file to root cgroup")
Signed-off-by: Dan Schatzberg <schatzberg.dan@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e20d00158 ]
Soon after registering a CRQ it is possible that we get a fail over or
maybe a CRQ_INIT from the VIOS while interrupts were disabled.
Look for any such CRQs after enabling interrupts.
Otherwise we can intermittently fail to bring up ibmvnic adapters during
boot, specially in kexec/kdump kernels.
Fixes: 032c5e8284 ("Driver for IBM System i/p VNIC protocol")
Reported-by: Vaishnavi Bhat <vaish123@in.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8878e46fcf ]
If adapter's resetting bit is on, discard the packet but don't stop the
transmit queue - instead leave that to the reset code. With this change,
it is possible that we may get several calls to ibmvnic_xmit() that simply
discard packets and return.
But if we stop the queue here, we might end up doing so just after
__ibmvnic_open() started the queues (during a hard/soft reset) and before
the ->resetting bit was cleared. If that happens, there will be no one to
restart queue and transmissions will be blocked indefinitely.
This can cause a TIMEOUT reset and with auto priority failover enabled,
an unnecessary FAILOVER reset to less favored backing device and then a
FAILOVER back to the most favored backing device. If we hit the window
repeatedly, we can get stuck in a loop of TIMEOUT, FAILOVER, FAILOVER
resets leaving the adapter unusable for extended periods of time.
Fixes: 7f5b030830 ("ibmvnic: Free skb's in cases of failure in transmit")
Reported-by: Abdul Haleem <abdhalee@in.ibm.com>
Reported-by: Vaishnavi Bhat <vaish123@in.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42dcfd850e ]
Commit c6af0c227a ("ip: support SO_MARK cmsg")
added propagation of SO_MARK from cmsg to skb->mark.
For IPv4 and raw sockets the mark also affects route
lookup, but in case of IPv6 the flow info is
initialized before cmsg is parsed.
Fixes: c6af0c227a ("ip: support SO_MARK cmsg")
Reported-and-tested-by: Xintong Hu <huxintong@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68b6dea802 ]
These three events can race when pcrypt is used multiple times in a
template ("pcrypt(pcrypt(...))"):
1. [taskA] The caller makes the crypto request via crypto_aead_encrypt()
2. [kworkerB] padata serializes the inner pcrypt request
3. [kworkerC] padata serializes the outer pcrypt request
3 might finish before the call to crypto_aead_encrypt() returns in 1,
resulting in two possible issues.
First, a use-after-free of the crypto request's memory when, for
example, taskA writes to the outer pcrypt request's padata->info in
pcrypt_aead_enc() after kworkerC completes the request.
Second, the outer pcrypt request overwrites the inner pcrypt request's
return code with -EINPROGRESS, making a successful request appear to
fail. For instance, kworkerB writes the outer pcrypt request's
padata->info in pcrypt_aead_done() and then taskA overwrites it
in pcrypt_aead_enc().
Avoid both situations by delaying the write of padata->info until after
the inner crypto request's return code is checked. This prevents the
use-after-free by not touching the crypto request's memory after the
next-inner crypto request is made, and stops padata->info from being
overwritten.
Fixes: 5068c7a883 ("crypto: pcrypt - Add pcrypt crypto parallelization wrapper")
Reported-by: syzbot+b187b77c8474f9648fae@syzkaller.appspotmail.com
Signed-off-by: Daniel Jordan <daniel.m.jordan@oracle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd8d9731bc ]
mvneta does not support asymetric pause modes, and it flags this by the
lack of AsymPause in the supported field. When setting pause modes, we
check that pause->rx_pause == pause->tx_pause, but only when pause
autoneg is enabled. When pause autoneg is disabled, we still allow
pause->rx_pause != pause->tx_pause, which is incorrect when the MAC
does not support asymetric pause, and causes mvneta to issue a warning.
Fix this by removing the test for pause->autoneg, so we always check
that pause->rx_pause == pause->tx_pause for network devices that do not
support AsymPause.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit daf182d360 ]
For each rate change command submission, the FW has to do a phy
power off sequence internally. For this to happen correctly, the
PLL re-initialization control setting has to be turned off before
sending mailbox commands and re-enabled once the command submission
is complete.
Without the PLL control setting, the link up takes longer time in a
fixed phy configuration.
Fixes: 47f164deab ("amd-xgbe: Add PCI device support")
Co-developed-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Signed-off-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3fc706e94 ]
Similar to the fix in commit:
e31eec77e4 ("bpf: selftests: Fix fd cleanup in get_branch_snapshot")
We use designated initializer to set fds to -1 without breaking on
future changes to MAX_SERVER constant denoting the array size.
The particular close(0) occurs on non-reuseport tests, so it can be seen
with -n 115/{2,3} but not 115/4. This can cause problems with future
tests if they depend on BTF fd never being acquired as fd 0, breaking
internal libbpf assumptions.
Fixes: 0ab5539f85 ("selftests/bpf: Tests for BPF_SK_LOOKUP attach point")
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20211028063501.2239335-8-memxor@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 113f304dbc ]
The firmware is offering features such as ARP offload, for which
firmware crafts its own (QoS)packets without waking up the host.
Point is that the sequence numbers generated by the firmware are
not in sync with the host mac80211 layer and can cause packets
such as firmware ARP reponses to be dropped by the AP (too old SN).
To fix this we need to let the firmware manages the sequence
numbers by its own (except for QoS null frames). There is a SN
counter for each QoS queue and one global/baseline counter for
Non-QoS.
Fixes: 84aff52e4f ("wcn36xx: Use sequence number allocated by mac80211")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635150336-18736-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9bfe38e064 ]
This is essentially exactly following the dma_wmb()/dma_rmb() usage
instructions in Documentation/memory-barriers.txt.
The theoretical races here are:
1. DXE (the DMA Transfer Engine in the Wi-Fi subsystem) seeing the
dxe->ctrl & WCN36xx_DXE_CTRL_VLD write before the dxe->dst_addr_l
write, thus performing DMA into the wrong address.
2. CPU reading dxe->dst_addr_l before DXE unsets dxe->ctrl &
WCN36xx_DXE_CTRL_VLD. This should generally be harmless since DXE
doesn't write dxe->dst_addr_l (no risk of freeing the wrong skb).
Fixes: 8e84c25821 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware")
Signed-off-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211023001528.3077822-1-benl@squareup.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 85f517b294 ]
If handle_sske cannot set the storage key, because there is no
page table entry or no present large page entry, it calls
fixup_user_fault.
However, currently, if the call succeeds, handle_sske returns
-EAGAIN, without having set the storage key.
Instead, retry by continue'ing the loop without incrementing the
address.
The same issue in handle_pfmf was fixed by
a11bdb1a6b ("KVM: s390: Fix pfmf and conditional skey emulation").
Fixes: bd096f6443 ("KVM: s390: Add skey emulation fault handling")
Signed-off-by: Janis Schoetterl-Glausch <scgl@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Link: https://lore.kernel.org/r/20211022152648.26536-1-scgl@linux.ibm.com
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f76fbbbb50 ]
Use the actual return value instead of always -1 if register_kretprobe()
failed.
E.g. without this patch:
# insmod samples/kprobes/kretprobe_example.ko func=no_such_func
insmod: ERROR: could not insert module samples/kprobes/kretprobe_example.ko: Operation not permitted
With this patch:
# insmod samples/kprobes/kretprobe_example.ko func=no_such_func
insmod: ERROR: could not insert module samples/kprobes/kretprobe_example.ko: Unknown symbol in module
Link: https://lkml.kernel.org/r/1635213091-24387-2-git-send-email-yangtiezhu@loongson.cn
Fixes: 804defea1c ("Kprobes: move kprobe examples to samples/")
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf12e6f912 ]
v1: Implement a more general statement as recommended by Eric Dumazet. The
sequence number will be advanced, so this check will fix the FIN case and
other cases.
A customer reported sockets stuck in the CLOSING state. A Vmcore revealed that
the write_queue was not empty as determined by tcp_write_queue_empty() but the
sk_buff containing the FIN flag had been freed and the socket was zombied in
that state. Corresponding pcaps show no FIN from the Linux kernel on the wire.
Some instrumentation was added to the kernel and it was found that there is a
timing window where tcp_sendmsg() can run after tcp_send_fin().
tcp_sendmsg() will hit an error, for example:
1269 ▹ if (sk->sk_err || (sk->sk_shutdown & SEND_SHUTDOWN))↩
1270 ▹ ▹ goto do_error;↩
tcp_remove_empty_skb() will then free the FIN sk_buff as "skb->len == 0". The
TCP socket is now wedged in the FIN-WAIT-1 state because the FIN is never sent.
If the other side sends a FIN packet the socket will transition to CLOSING and
remain that way until the system is rebooted.
Fix this by checking for the FIN flag in the sk_buff and don't free it if that
is the case. Testing confirmed that fixed the issue.
Fixes: fdfc5c8594 ("tcp: remove empty skb from write queue in error cases")
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Reported-by: Monir Zouaoui <Monir.Zouaoui@mail.schwarz>
Reported-by: Simon Stier <simon.stier@mail.schwarz>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45f2bebc80 ]
__BYTE_ORDER is supposed to be defined by a libc, and __BYTE_ORDER__ -
by a compiler. bpf_core_read.h checks __BYTE_ORDER == __LITTLE_ENDIAN,
which is true if neither are defined, leading to incorrect behavior on
big-endian hosts if libc headers are not included, which is often the
case.
Fixes: ee26dade0e ("libbpf: Add support for relocatable bitfields")
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20211026010831.748682-2-iii@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7eba41fe8c ]
In commit c46ed2281b ("tpm_tis_spi: add missing SPI device ID entries")
we added SPI IDs for all the DT aliases to handle the fact that we always
use SPI modaliases to load modules even when probed via DT however the
mentioned commit missed that the SPI and OF device ID entries did not
match and were different and so DT nodes with compatible
"tcg,tpm_tis-spi" will not match. Add an extra ID for tpm_tis-spi
rather than just fix the existing one since what's currently there is
going to be better for anyone actually using SPI IDs to instantiate.
Fixes: c46ed2281b ("tpm_tis_spi: add missing SPI device ID entries")
Fixes: 96c8395e21 ("spi: Revert modalias changes")
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79ca6f74da ]
The Atmel TPM 1.2 chips crash with error
`tpm_try_transmit: send(): error -62` since kernel 4.14.
It is observed from the kernel log after running `tpm_sealdata -z`.
The error thrown from the command is as follows
```
$ tpm_sealdata -z
Tspi_Key_LoadKey failed: 0x00001087 - layer=tddl,
code=0087 (135), I/O error
```
The issue was reproduced with the following Atmel TPM chip:
```
$ tpm_version
T0 TPM 1.2 Version Info:
Chip Version: 1.2.66.1
Spec Level: 2
Errata Revision: 3
TPM Vendor ID: ATML
TPM Version: 01010000
Manufacturer Info: 41544d4c
```
The root cause of the issue is due to the TPM calls to msleep()
were replaced with usleep_range() [1], which reduces
the actual timeout. Via experiments, it is observed that
the original msleep(5) actually sleeps for 15ms.
Because of a known timeout issue in Atmel TPM 1.2 chip,
the shorter timeout than 15ms can cause the error described above.
A few further changes in kernel 4.16 [2] and 4.18 [3, 4] further
reduced the timeout to less than 1ms. With experiments,
the problematic timeout in the latest kernel is the one
for `wait_for_tpm_stat`.
To fix it, the patch reverts the timeout of `wait_for_tpm_stat`
to 15ms for all Atmel TPM 1.2 chips, but leave it untouched
for Ateml TPM 2.0 chip, and chips from other vendors.
As explained above, the chosen 15ms timeout is
the actual timeout before this issue introduced,
thus the old value is used here.
Particularly, TPM_ATML_TIMEOUT_WAIT_STAT_MIN is set to 14700us,
TPM_ATML_TIMEOUT_WAIT_STAT_MIN is set to 15000us according to
the existing TPM_TIMEOUT_RANGE_US (300us).
The fixed has been tested in the system with the affected Atmel chip
with no issues observed after boot up.
References:
[1] 9f3fc7bcdd tpm: replace msleep() with usleep_range() in TPM
1.2/2.0 generic drivers
[2] cf151a9a44 tpm: reduce tpm polling delay in tpm_tis_core
[3] 59f5a6b07f tpm: reduce poll sleep time in tpm_transmit()
[4] 424eaf910c tpm: reduce polling time to usecs for even finer
granularity
Fixes: 9f3fc7bcdd ("tpm: replace msleep() with usleep_range() in TPM 1.2/2.0 generic drivers")
Link: https://patchwork.kernel.org/project/linux-integrity/patch/20200926223150.109645-1-hao.wu@rubrik.com/
Signed-off-by: Hao Wu <hao.wu@rubrik.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c65b52d02f ]
As bcm6345_l1_irq_handle() is a chained irqchip handler, it will be
invoked within the context of the root irqchip handler, which must have
entered IRQ context already.
When bcm6345_l1_irq_handle() calls arch/mips's do_IRQ() , this will nest
another call to irq_enter(), and the resulting nested increment to
`rcu_data.dynticks_nmi_nesting` will cause rcu_is_cpu_rrupt_from_idle()
to fail to identify wakeups from idle, resulting in failure to preempt,
and RCU stalls.
Chained irqchip handlers must invoke IRQ handlers by way of thee core
irqchip code, i.e. generic_handle_irq() or generic_handle_domain_irq()
and should not call do_IRQ(), which is intended only for root irqchip
handlers.
Fix bcm6345_l1_irq_handle() by calling generic_handle_irq() directly.
Fixes: c7c42ec2ba ("irqchips/bmips: Add bcm6345-l1 interrupt controller")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d4074324b0 ]
If kvm_s390_pv_destroy_cpu is called more than once, we risk calling
free_page on a random page, since the sidad field is aliased with the
gbea, which is not guaranteed to be zero.
This can happen, for example, if userspace calls the KVM_PV_DISABLE
IOCTL, and it fails, and then userspace calls the same IOCTL again.
This scenario is only possible if KVM has some serious bug or if the
hardware is broken.
The solution is to simply return successfully immediately if the vCPU
was already non secure.
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Fixes: 19e1227768 ("KVM: S390: protvirt: Introduce instruction data area bounce buffer")
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <20210920132502.36111-3-imbrenda@linux.ibm.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b159f94c86 ]
... otherwise we will try unlocking a spinlock that was never locked via a
garbage pointer.
At the time we reach this code path, we usually successfully looked up
a PGSTE already; however, evil user space could have manipulated the VMA
layout in the meantime and triggered removal of the page table.
Fixes: 1e133ab296 ("s390/mm: split arch/s390/mm/pgtable.c")
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Link: https://lore.kernel.org/r/20210909162248.14969-3-david@redhat.com
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5245dafe3d ]
btf_header's str_off+str_len or type_off+type_len can overflow as they
are u32s. This will lead to bypassing the sanity checks during BTF
parsing, resulting in crashes afterwards. Fix by using 64-bit signed
integers for comparison.
Fixes: d812362450 ("libbpf: Fix BTF data layout checks and allow empty BTF")
Reported-by: Evgeny Vereshchagin <evvers@ya.ru>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20211023003157.726961-1-andrii@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d812362450 ]
Make data section layout checks stricter, disallowing overlap of types and
strings data.
Additionally, allow BTFs with no type data. There is nothing inherently wrong
with having BTF with no types (put potentially with some strings). This could
be a situation with kernel module BTFs, if module doesn't introduce any new
type information.
Also fix invalid offset alignment check for btf->hdr->type_off.
Fixes: 8a138aed4a ("bpf: btf: Add BTF support to libbpf")
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20201105043402.2530976-8-andrii@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e89ef634f8 ]
Bpftool creates a new JSON object for writing program metadata in plain
text mode, regardless of metadata being present or not. Then this writer
is freed if any metadata has been found and printed, but it leaks
otherwise. We cannot destroy the object unconditionally, because the
destructor prints an undesirable line break. Instead, make sure the
writer is created only after we have found program metadata to print.
Found with valgrind.
Fixes: aff52e685e ("bpftool: Support dumping metadata")
Signed-off-by: Quentin Monnet <quentin@isovalent.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20211022094743.11052-1-quentin@isovalent.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed290e1c20 ]
Though gcc conveniently compiles a simple memset to "rep stos," clang
prefers to call the libc version of memset. If a test is dynamically
linked, the libc memset isn't available in L1 (nor is the PLT or the
GOT, for that matter). Even if the test is statically linked, the libc
memset may choose to use some CPU features, like AVX, which may not be
enabled in L1. Note that __builtin_memset doesn't solve the problem,
because (a) the compiler is free to call memset anyway, and (b)
__builtin_memset may also choose to use features like AVX, which may
not be available in L1.
To avoid a myriad of problems, use an explicit "rep stos" to clear the
VMCB in generic_svm_setup(), which is called both from L0 and L1.
Reported-by: Ricardo Koller <ricarkol@google.com>
Signed-off-by: Jim Mattson <jmattson@google.com>
Fixes: 20ba262f86 ("selftests: KVM: AMD Nested test infrastructure")
Message-Id: <20210930003649.4026553-1-jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47bc726fe8 ]
Building the KVM selftests with LLVM's integrated assembler fails with:
$ CFLAGS=-fintegrated-as make -C tools/testing/selftests/kvm CC=clang
lib/x86_64/svm.c:77:16: error: too few operands for instruction
asm volatile ("vmsave\n\t" : : "a" (vmcb_gpa) : "memory");
^
<inline asm>:1:2: note: instantiated into assembly here
vmsave
^
lib/x86_64/svm.c:134:3: error: too few operands for instruction
"vmload\n\t"
^
<inline asm>:1:2: note: instantiated into assembly here
vmload
^
This is because LLVM IAS does not currently support calling vmsave,
vmload, or vmload without an explicit %rax operand.
Add an explicit operand to vmsave, vmload, and vmrum in svm.c. Fixing
this was suggested by Sean Christopherson.
Tested: building without this error in clang 11. The following patch
(not queued yet) needs to be applied to solve the other remaining error:
"selftests: kvm: remove reassignment of non-absolute variables".
Suggested-by: Sean Christopherson <seanjc@google.com>
Link: https://lore.kernel.org/kvm/X+Df2oQczVBmwEzi@google.com/
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Ricardo Koller <ricarkol@google.com>
Message-Id: <20210210031719.769837-1-ricarkol@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 01de5fcd8b ]
When building the kernel with sparse enabled 'C=1' the following
warnings shows up:
kernel/power/swap.c:390:29: warning: incorrect type in assignment (different base types)
kernel/power/swap.c:390:29: expected int ret
kernel/power/swap.c:390:29: got restricted blk_status_t
This is due to function hib_wait_io() returns a 'blk_status_t' which is
a bitwise u8. Commit 5416da01ff ("PM: hibernate: Remove
blk_status_to_errno in hib_wait_io") seemed to have mixed up the return
type. However, the 4e4cbee93d ("block: switch bios to blk_status_t")
actually broke the behaviour by returning the wrong type.
Rework so function hib_wait_io() returns a 'int' instead of
'blk_status_t' and make sure to call function
blk_status_to_errno(hb->error)' when returning from function
hib_wait_io() a int gets returned.
Fixes: 4e4cbee93d ("block: switch bios to blk_status_t")
Fixes: 5416da01ff ("PM: hibernate: Remove blk_status_to_errno in hib_wait_io")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0974812200 ]
In case that icdoff is not zero or mandatory keyed sgls are not
supported by the NVMe/RDMA target, we'll go to error flow but we'll
return 0 to the caller. Fix it by returning an appropriate error code.
Fixes: c66e2998c8 ("nvme-rdma: centralize controller setup sequence")
Signed-off-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2641b62d2f ]
Some Micrel KSZ8041NL PHY chips exhibit continuous RX errors after using
the power down mode bit (0.11). If the PHY is taken out of power down
mode in a certain temperature range, the PHY enters a weird state which
leads to continuously reporting RX errors. In that state, the MAC is not
able to receive or send any Ethernet frames and the activity LED is
constantly blinking. Since Linux is using the suspend callback when the
interface is taken down, ending up in that state can easily happen
during a normal startup.
Micrel confirmed the issue in errata DS80000700A [*], caused by abnormal
clock recovery when using power down mode. Even the latest revision (A4,
Revision ID 0x1513) seems to suffer that problem, and according to the
errata is not going to be fixed.
Remove the suspend/resume callback to avoid using the power down mode
completely.
[*] https://ww1.microchip.com/downloads/en/DeviceDoc/80000700A.pdf
Fixes: 1a5465f5d6 ("phy/micrel: Add suspend/resume support to Micrel PHYs")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd4bc63de7 ]
Coverity complains of a possible dereference of a null return value.
5. returned_null: kzalloc returns NULL. [show details]
6. var_assigned: Assigning: si_data = NULL return value from kzalloc.
488 si_data = kzalloc(data_size, __GFP_DMA | GFP_KERNEL);
489 cbd.length = cpu_to_le16(data_size);
490
491 dma = dma_map_single(&priv->si->pdev->dev, si_data,
492 data_size, DMA_FROM_DEVICE);
While this kzalloc() is unlikely to fail, I did notice that the function
returned without unmapping si_data.
Fix this by refactoring the error paths and checking for kzalloc()
failure.
Fixes: 888ae5a395 ("net: enetc: add tc flower psfp offload driver")
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org (open list)
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Acked-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc8a8bc374 ]
While looking at on-air packets using Wireshark, I noticed we're never
setting the initiator bit when sending DELBA requests to the AP: While
we set the bit on our del_ba_param_set bitmask, we forget to actually
copy that bitmask over to the command struct, which means we never
actually set the initiator bit.
Fix that and copy the bitmask over to the host_cmd_ds_11n_delba command
struct.
Fixes: 5e6e3a92b9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Acked-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211016153244.24353-5-verdre@v0yd.nl
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 515e7184bd ]
When fail to init coex module, free 'common' and 'adapter' directly, but
common->tx_thread which will access 'common' and 'adapter' is running at
the same time. That will trigger the UAF bug.
==================================================================
BUG: KASAN: use-after-free in rsi_tx_scheduler_thread+0x50f/0x520 [rsi_91x]
Read of size 8 at addr ffff8880076dc000 by task Tx-Thread/124777
CPU: 0 PID: 124777 Comm: Tx-Thread Not tainted 5.15.0-rc5+ #19
Call Trace:
dump_stack_lvl+0xe2/0x152
print_address_description.constprop.0+0x21/0x140
? rsi_tx_scheduler_thread+0x50f/0x520
kasan_report.cold+0x7f/0x11b
? rsi_tx_scheduler_thread+0x50f/0x520
rsi_tx_scheduler_thread+0x50f/0x520
...
Freed by task 111873:
kasan_save_stack+0x1b/0x40
kasan_set_track+0x1c/0x30
kasan_set_free_info+0x20/0x30
__kasan_slab_free+0x109/0x140
kfree+0x117/0x4c0
rsi_91x_init+0x741/0x8a0 [rsi_91x]
rsi_probe+0x9f/0x1750 [rsi_usb]
Stop thread before free 'common' and 'adapter' to fix it.
Fixes: 2108df3c4b ("rsi: add coex support")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211015040335.1021546-1-william.xuanziyang@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit afa0370f3a ]
Fix tag len error for sta_rec_wtbl, which causes fw parsing error for
the tags placed behind it.
Fixes: e57b790146 ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c33edef520 ]
Fix the following sparse warning in mt76x02_mac_write_txwi and
mt76x02_mac_tx_rate_val routines:
drivers/net/wireless/mediatek/mt76/mt76x02_mac.c:237:19:
warning: restricted __le16 degrades to intege
warning: cast from restricted __le16
drivers/net/wireless/mediatek/mt76/mt76x02_mac.c:383:28:
warning: incorrect type in assignment (different base types)
expected restricted __le16 [usertype] rate
got unsigned long
Fixes: db9f11d343 ("mt76: store wcid tx rate info in one u32 reduce locking")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd96e35ea7 ]
A new warning in clang points out a use of bitwise OR with boolean
expressions in this driver:
drivers/platform/x86/thinkpad_acpi.c:9061:11: error: use of bitwise '|' with boolean operands [-Werror,-Wbitwise-instead-of-logical]
else if ((strlencmp(cmd, "level disengaged") == 0) |
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
||
drivers/platform/x86/thinkpad_acpi.c:9061:11: note: cast one or both operands to int to silence this warning
1 error generated.
This should clearly be a logical OR so change it to fix the warning.
Fixes: fe98a52ce7 ("ACPI: thinkpad-acpi: add sysfs support to fan subdriver")
Link: https://github.com/ClangBuiltLinux/linux/issues/1476
Reported-by: Tor Vic <torvic9@mailbox.org>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20211018182537.2316800-1-nathan@kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24bcbe1cc6 ]
sk_stream_kill_queues() can be called on close when there are
still outstanding skbs to transmit. Those skbs may try to queue
notifications to the error queue (e.g. timestamps).
If sk_stream_kill_queues() purges the queue without taking
its lock the queue may get corrupted, and skbs leaked.
This shows up as a warning about an rmem leak:
WARNING: CPU: 24 PID: 0 at net/ipv4/af_inet.c:154 inet_sock_destruct+0x...
The leak is always a multiple of 0x300 bytes (the value is in
%rax on my builds, so RAX: 0000000000000300). 0x300 is truesize of
an empty sk_buff. Indeed if we dump the socket state at the time
of the warning the sk_error_queue is often (but not always)
corrupted. The ->next pointer points back at the list head,
but not the ->prev pointer. Indeed we can find the leaked skb
by scanning the kernel memory for something that looks like
an skb with ->sk = socket in question, and ->truesize = 0x300.
The contents of ->cb[] of the skb confirms the suspicion that
it is indeed a timestamp notification (as generated in
__skb_complete_tx_timestamp()).
Removing purging of sk_error_queue should be okay, since
inet_sock_destruct() does it again once all socket refs
are gone. Eric suggests this may cause sockets that go
thru disconnect() to maintain notifications from the
previous incarnations of the socket, but that should be
okay since the race was there anyway, and disconnect()
is not exactly dependable.
Thanks to Jonathan Lemon and Omar Sandoval for help at various
stages of tracing the issue.
Fixes: cb9eff0978 ("net: new user space API for time stamping of incoming and outgoing packets")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2203bd0e5c ]
The msm_gem_new_impl() function cleans up after itself so there is no
need to call drm_gem_object_put(). Conceptually, it does not make sense
to call a kref_put() function until after the reference counting has
been initialized which happens immediately after this call in the
drm_gem_(private_)object_init() functions.
In the msm_gem_import() function the "obj" pointer is uninitialized, so
it will lead to a crash.
Fixes: 05b849111c ("drm/msm: prime support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211013081315.GG6010@kili
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19757cebf0 ]
Use of percpu_counter structure to track count of orphaned
sockets is causing problems on modern hosts with 256 cpus
or more.
Stefan Bach reported a serious spinlock contention in real workloads,
that I was able to reproduce with a netfilter rule dropping
incoming FIN packets.
53.56% server [kernel.kallsyms] [k] queued_spin_lock_slowpath
|
---queued_spin_lock_slowpath
|
--53.51%--_raw_spin_lock_irqsave
|
--53.51%--__percpu_counter_sum
tcp_check_oom
|
|--39.03%--__tcp_close
| tcp_close
| inet_release
| inet6_release
| sock_close
| __fput
| ____fput
| task_work_run
| exit_to_usermode_loop
| do_syscall_64
| entry_SYSCALL_64_after_hwframe
| __GI___libc_close
|
--14.48%--tcp_out_of_resources
tcp_write_timeout
tcp_retransmit_timer
tcp_write_timer_handler
tcp_write_timer
call_timer_fn
expire_timers
__run_timers
run_timer_softirq
__softirqentry_text_start
As explained in commit cf86a086a1 ("net/dst: use a smaller percpu_counter
batch for dst entries accounting"), default batch size is too big
for the default value of tcp_max_orphans (262144).
But even if we reduce batch sizes, there would still be cases
where the estimated count of orphans is beyond the limit,
and where tcp_too_many_orphans() has to call the expensive
percpu_counter_sum_positive().
One solution is to use plain per-cpu counters, and have
a timer to periodically refresh this cache.
Updating this cache every 100ms seems about right, tcp pressure
state is not radically changing over shorter periods.
percpu_counter was nice 15 years ago while hosts had less
than 16 cpus, not anymore by current standards.
v2: Fix the build issue for CONFIG_CRYPTO_DEV_CHELSIO_TLS=m,
reported by kernel test robot <lkp@intel.com>
Remove unused socket argument from tcp_too_many_orphans()
Fixes: dd24c00191 ("net: Use a percpu_counter for orphan_count")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Stefan Bach <sfb@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ef0c5c6b5 ]
There is a small race between copy_process() and sched_fork()
where child->sched_task_group point to an already freed pointer.
parent doing fork() | someone moving the parent
| to another cgroup
-------------------------------+-------------------------------
copy_process()
+ dup_task_struct()<1>
parent move to another cgroup,
and free the old cgroup. <2>
+ sched_fork()
+ __set_task_cpu()<3>
+ task_fork_fair()
+ sched_slice()<4>
In the worst case, this bug can lead to "use-after-free" and
cause panic as shown above:
(1) parent copy its sched_task_group to child at <1>;
(2) someone move the parent to another cgroup and free the old
cgroup at <2>;
(3) the sched_task_group and cfs_rq that belong to the old cgroup
will be accessed at <3> and <4>, which cause a panic:
[] BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
[] PGD 8000001fa0a86067 P4D 8000001fa0a86067 PUD 2029955067 PMD 0
[] Oops: 0000 [#1] SMP PTI
[] CPU: 7 PID: 648398 Comm: ebizzy Kdump: loaded Tainted: G OE --------- - - 4.18.0.x86_64+ #1
[] RIP: 0010:sched_slice+0x84/0xc0
[] Call Trace:
[] task_fork_fair+0x81/0x120
[] sched_fork+0x132/0x240
[] copy_process.part.5+0x675/0x20e0
[] ? __handle_mm_fault+0x63f/0x690
[] _do_fork+0xcd/0x3b0
[] do_syscall_64+0x5d/0x1d0
[] entry_SYSCALL_64_after_hwframe+0x65/0xca
[] RIP: 0033:0x7f04418cd7e1
Between cgroup_can_fork() and cgroup_post_fork(), the cgroup
membership and thus sched_task_group can't change. So update child's
sched_task_group at sched_post_fork() and move task_fork() and
__set_task_cpu() (where accees the sched_task_group) from sched_fork()
to sched_post_fork().
Fixes: 8323f26ce3 ("sched: Fix race in task_group")
Signed-off-by: Zhang Qiao <zhangqiao22@huawei.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lkml.kernel.org/r/20210915064030.2231-1-zhangqiao22@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a491167fe ]
Most of the txpower for the ath10k firmware is stored as twicepower (0.5 dB
steps). This isn't the case for max_antenna_gain - which is still expected
by the firmware as dB.
The firmware is converting it from dB to the internal (twicepower)
representation when it calculates the limits of a channel. This can be seen
in tpc_stats when configuring "12" as max_antenna_gain. Instead of the
expected 12 (6 dB), the tpc_stats shows 24 (12 dB).
Tested on QCA9888 and IPQ4019 with firmware 10.4-3.5.3-00057.
Fixes: 02256930d9 ("ath10k: use proper tx power unit")
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20190611172131.6064-1-sven@narfation.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ada61aa0b1 ]
I got memory leak as follows when doing fault injection test:
unreferenced object 0xffff888102740438 (size 8):
comm "27", pid 859, jiffies 4295031351 (age 143.992s)
hex dump (first 8 bytes):
68 77 6d 6f 6e 30 00 00 hwmon0..
backtrace:
[<00000000544b5996>] __kmalloc_track_caller+0x1a6/0x300
[<00000000df0d62b9>] kvasprintf+0xad/0x140
[<00000000d3d2a3da>] kvasprintf_const+0x62/0x190
[<000000005f8f0f29>] kobject_set_name_vargs+0x56/0x140
[<00000000b739e4b9>] dev_set_name+0xb0/0xe0
[<0000000095b69c25>] __hwmon_device_register+0xf19/0x1e50 [hwmon]
[<00000000a7e65b52>] hwmon_device_register_with_info+0xcb/0x110 [hwmon]
[<000000006f181e86>] devm_hwmon_device_register_with_info+0x85/0x100 [hwmon]
[<0000000081bdc567>] tmp421_probe+0x2d2/0x465 [tmp421]
[<00000000502cc3f8>] i2c_device_probe+0x4e1/0xbb0
[<00000000f90bda3b>] really_probe+0x285/0xc30
[<000000007eac7b77>] __driver_probe_device+0x35f/0x4f0
[<000000004953d43d>] driver_probe_device+0x4f/0x140
[<000000002ada2d41>] __device_attach_driver+0x24c/0x330
[<00000000b3977977>] bus_for_each_drv+0x15d/0x1e0
[<000000005bf2a8e3>] __device_attach+0x267/0x410
When device_register() returns an error, the name allocated in
dev_set_name() will be leaked, the put_device() should be used
instead of calling hwmon_dev_release() to give up the device
reference, then the name will be freed in kobject_cleanup().
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: bab2243ce1 ("hwmon: Introduce hwmon_device_register_with_groups")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20211012112758.2681084-1-yangyingliang@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4400bbf5b ]
The NTF_EXT_LEARNED neigh flag is usually propagated back to user space
upon dump of the neighbor table. However, when used in combination with
NTF_USE flag this is not the case despite exempting the entry from the
garbage collector. This results in inconsistent state since entries are
typically marked in neigh->flags with NTF_EXT_LEARNED, but here they are
not. Fix it by propagating the creation flag to ___neigh_create().
Before fix:
# ./ip/ip n replace 192.168.178.30 dev enp5s0 use extern_learn
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a REACHABLE
[...]
After fix:
# ./ip/ip n replace 192.168.178.30 dev enp5s0 use extern_learn
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a extern_learn REACHABLE
[...]
Fixes: 9ce33e4653 ("neighbour: support for NTF_EXT_LEARNED flag")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Roopa Prabhu <roopa@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit beae4a6258 ]
The "msh" pointer is device managed, meaning that memstick_alloc_host()
calls device_initialize() on it. That means that it can't be free
using kfree() but must instead be freed with memstick_free_host().
Otherwise it leads to a tiny memory leak of device resources.
Fixes: 60fdd931d5 ("memstick: add support for JMicron jmb38x MemoryStick host controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211011123912.GD15188@kili
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4853396f03 ]
clang-14 complains about a sanity check that always passes when the
page size is 64KB or larger:
drivers/memstick/core/ms_block.c:1739:21: error: result of comparison of constant 65536 with expression of type 'unsigned short' is always false [-Werror,-Wtautological-constant-out-of-range-compare]
if (msb->page_size > PAGE_SIZE) {
~~~~~~~~~~~~~~ ^ ~~~~~~~~~
This is fine, it will still work on all architectures, so just shut
up that warning with a cast.
Fixes: 0ab30494bc ("memstick: add support for legacy memorysticks")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210927094520.696665-1-arnd@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d806e334d0 ]
We need to restore context in a specified order with HCTL set in two
phases. This is similar to what omap_hsmmc_context_restore() is doing.
Otherwise SDIO can stop working on resume.
And for PM runtime and SDIO cards, we need to also save SYSCTL, IE and
ISE.
This should not be a problem currently, and these patches can be applied
whenever suitable.
Fixes: ee0f309263 ("mmc: sdhci-omap: Add Support for Suspend/Resume")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210921110029.21944-3-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e0e7bd38b ]
If sdhci-omap is configured for an unused device instance and the device
is not set as disabled, we can get a NULL pointer dereference:
Unable to handle kernel NULL pointer dereference at virtual address
00000045
...
(regulator_set_voltage) from [<c07d7008>] (mmc_regulator_set_ocr+0x44/0xd0)
(mmc_regulator_set_ocr) from [<c07e2d80>] (sdhci_set_ios+0xa4/0x490)
(sdhci_set_ios) from [<c07ea690>] (sdhci_omap_set_ios+0x124/0x160)
(sdhci_omap_set_ios) from [<c07c8e94>] (mmc_power_up.part.0+0x3c/0x154)
(mmc_power_up.part.0) from [<c07c9d20>] (mmc_start_host+0x88/0x9c)
(mmc_start_host) from [<c07cad34>] (mmc_add_host+0x58/0x7c)
(mmc_add_host) from [<c07e2574>] (__sdhci_add_host+0xf0/0x22c)
(__sdhci_add_host) from [<c07eaf68>] (sdhci_omap_probe+0x318/0x72c)
(sdhci_omap_probe) from [<c06a39d8>] (platform_probe+0x58/0xb8)
AFAIK we are not seeing this with the devices configured in the mainline
kernel but this can cause issues for folks bringing up their boards.
Fixes: 7d326930d3 ("mmc: sdhci-omap: Add OMAP SDHCI driver")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210921110029.21944-2-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87a7f321bb ]
Don't always reset the driver on a TX timeout. Attempt to
recover by kicking the queue in case an IRQ was missed.
Fixes: 9e5f7d26a4 ("gve: Add workqueue and reset support")
Signed-off-by: John Fraker <jfraker@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b793db5fc ]
The problem is that "channel" is an unsigned int, when it's less 5 the
value of "channel - 5" is not a negative number as one would expect but
is very high positive value instead.
This means that "start" becomes a very high positive value. The result
of that is that we never enter the "for (i = start; i <= end; i++) {"
loop. Instead of storing the result from b43legacy_radio_aci_detect()
it just uses zero.
Fixes: ef1a628d83 ("b43: Implement dynamic PHY API")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Michael Büsch <m@bues.ch>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211006073621.GE8404@kili
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1c8380b03 ]
The problem is that "channel" is an unsigned int, when it's less 5 the
value of "channel - 5" is not a negative number as one would expect but
is very high positive value instead.
This means that "start" becomes a very high positive value. The result
of that is that we never enter the "for (i = start; i <= end; i++) {"
loop. Instead of storing the result from b43legacy_radio_aci_detect()
it just uses zero.
Fixes: 75388acd0c ("[B43LEGACY]: add mac80211-based driver for legacy BCM43xx devices")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Michael Büsch <m@bues.ch>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211006073542.GD8404@kili
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6f5f0c8f7 ]
Currently mtk_rng_runtime_suspend/resume is called for both runtime pm
and system sleep operations.
This is wrong as these should only be runtime ops as the name already
suggests. Currently freezing the system will lead to a call to
mtk_rng_runtime_suspend even if the device currently isn't active. This
leads to a clock warning because it is disabled/unprepared although it
isn't enabled/prepared currently.
This patch fixes this by only setting the runtime pm ops and forces to
call the runtime pm ops from the system sleep ops as well if active but
not otherwise.
Fixes: 81d2b34508 ("hwrng: mtk - add runtime PM support")
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 18fcba469b ]
Upon receiving a PFVF message, check if the interrupt bit is set in the
message. If it is not, that means that the interrupt was probably
triggered by a collision. In this case, disregard the message and
re-enable the interrupts.
Fixes: ed8ccaef52 ("crypto: qat - Add support for SRIOV")
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b768e8a39 ]
Detect a PFVF collision between the local and the remote function by
checking if the message on the PFVF CSR has been overwritten.
This is done after the remote function confirms that the message has
been received, by clearing the interrupt bit, or the maximum number of
attempts (ADF_IOV_MSG_ACK_MAX_RETRY) to check the CSR has been exceeded.
Fixes: ed8ccaef52 ("crypto: qat - Add support for SRIOV")
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Co-developed-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69a10678e2 ]
mn88443x_cmn_power_on() did not handle possible errors of
clk_prepare_enable() and always finished successfully so that its caller
mn88443x_probe() did not care about failed preparing/enabling of clocks
as well.
Add missed error handling in both mn88443x_cmn_power_on() and
mn88443x_probe(). This required to change the return value of the former
from "void" to "int".
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 0f408ce894 ("media: dvb-frontends: add Socionext MN88443x ISDB-S/T demodulator driver")
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Co-developed-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Signed-off-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b1394892d ]
Relax this condition to make add and update commands idempotent for sets
with no timeout. The eval function already checks if the set element
timeout is available and updates it if the update command is used.
Fixes: 22fe54d5fe ("netfilter: nf_tables: add support for dynamic set updates")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7663ad9a5d ]
RCU managed to grow a few noinstr violations:
vmlinux.o: warning: objtool: rcu_dynticks_eqs_enter()+0x0: call to rcu_dynticks_task_trace_enter() leaves .noinstr.text section
vmlinux.o: warning: objtool: rcu_dynticks_eqs_exit()+0xe: call to rcu_dynticks_task_trace_exit() leaves .noinstr.text section
Fix them by adding __always_inline to the relevant trivial functions.
Also replace the noinstr with __always_inline for the existing
rcu_dynticks_task_*() functions since noinstr would force noinline
them, even when empty, which seems silly.
Fixes: 7d0c9c50c5 ("rcu-tasks: Avoid IPIing userspace/idle tasks if kernel is so built")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f4873fb6a ]
AMD Rome systems and later support interleaving between three identical
ranks within a channel.
Check for this mode by counting the number of enabled chip selects and
comparing their masks. If there are exactly three enabled chip selects
and their masks are identical, then three rank interleaving is enabled.
The size of a rank is determined from its mask value. However, three
rank interleaving doesn't follow the method of swapping an interleave
bit with the most significant bit. Rather, the interleave bit is flipped
and the most significant bit remains the same. There is only a single
interleave bit in this case.
Account for this when determining the chip select size by keeping the
most significant bit at its original value and ignoring any zero bits.
This will return a full bitmask in [MSB:1].
Fixes: e53a3b267f ("EDAC/amd64: Find Chip Select memory size using Address Mask")
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20211005154419.2060504-1-yazen.ghannam@amd.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa1a43262a ]
Currently, a debug message is printed if an inefficient state is detected
in the Energy Model. Unfortunately, it won't detect if the first state is
inefficient or if two successive states are. Fix this behavior.
Fixes: 27871f7a8a (PM: Introduce an Energy Model management framework)
Signed-off-by: Vincent Donnefort <vincent.donnefort@arm.com>
Reviewed-by: Quentin Perret <qperret@google.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4925642d54 ]
In tests with two Lima boards from 8devices (QCA4531 based) on OpenWrt
19.07 we could force a silent restart of a device with no serial
output when we were sending a high amount of UDP traffic (iperf3 at 80
MBit/s in both directions from external hosts, saturating the wifi and
causing a load of about 4.5 to 6) and were then triggering an
ath9k_queue_reset().
Further debugging showed that the restart was caused by the ath79
watchdog. With disabled watchdog we could observe that the device was
constantly going into ath_isr() interrupt handler and was returning
early after the ATH_OP_HW_RESET flag test, without clearing any
interrupts. Even though ath9k_queue_reset() calls
ath9k_hw_kill_interrupts().
With JTAG we could observe the following race condition:
1) ath9k_queue_reset()
...
-> ath9k_hw_kill_interrupts()
-> set_bit(ATH_OP_HW_RESET, &common->op_flags);
...
<- returns
2) ath9k_tasklet()
...
-> ath9k_hw_resume_interrupts()
...
<- returns
3) loops around:
...
handle_int()
-> ath_isr()
...
-> if (test_bit(ATH_OP_HW_RESET,
&common->op_flags))
return IRQ_HANDLED;
x) ath_reset_internal():
=> never reached <=
And in ath_isr() we would typically see the following interrupts /
interrupt causes:
* status: 0x00111030 or 0x00110030
* async_cause: 2 (AR_INTR_MAC_IPQ)
* sync_cause: 0
So the ath9k_tasklet() reenables the ath9k interrupts
through ath9k_hw_resume_interrupts() which ath9k_queue_reset() had just
disabled. And ath_isr() then keeps firing because it returns IRQ_HANDLED
without actually clearing the interrupt.
To fix this IRQ storm also clear/disable the interrupts again when we
are in reset state.
Cc: Sven Eckelmann <sven@narfation.org>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Cc: Linus Lüssing <linus.luessing@c0d3.blue>
Fixes: 872b5d814f ("ath9k: do not access hardware on IRQs during reset")
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914192515.9273-3-linus.luessing@c0d3.blue
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51fa3b70d2 ]
The call to ops->suspend for the dev->dev_next case can currently
trigger a call on a null function pointer if ops->suspend is null.
Skip over the use of function ops->suspend if it is null.
Addresses-Coverity: ("Dereference after null check")
Fixes: be7fd3c3a8 ("media: em28xx: Hauppauge DualHD second tuner functionality")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5f5a66c9a ]
Commit c343bf1ba5 ("cpuidle: Fix three reference count leaks")
fixes the cleanup of kobjects; however, it removes kfree() calls
altogether, leading to memory leaks.
Fix those and also defer the initialization of dev->kobj_dev until
after the error check, so that we do not end up with a dangling
pointer.
Fixes: c343bf1ba5 ("cpuidle: Fix three reference count leaks")
Signed-off-by: Anel Orazgaliyeva <anelkz@amazon.de>
Suggested-by: Aman Priyadarshi <apeureka@amazon.de>
[ rjw: Subject edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 38aa192a05 ]
The ecc.c file started out as part of the ECDH algorithm but got
moved out into a standalone module later. It does not build without
CRYPTO_DEFAULT_RNG, so now that other modules are using it as well we
can run into this link error:
aarch64-linux-ld: ecc.c:(.text+0xfc8): undefined reference to `crypto_default_rng'
aarch64-linux-ld: ecc.c:(.text+0xff4): undefined reference to `crypto_put_default_rng'
Move the 'select CRYPTO_DEFAULT_RNG' statement into the correct symbol.
Fixes: 0d7a78643f ("crypto: ecrdsa - add EC-RDSA (GOST 34.10) algorithm")
Fixes: 4e6602916b ("crypto: ecdsa - Add support for ECDSA signature verification")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f7262cd66 ]
debugfs_create_file() takes a pointer argument that can be used during
file operation callbacks (accessible via i_private in the inode
structure). An obvious requirement is for the pointer to refer to
valid memory when used.
When creating the debugfs file to dynamically enable / disable
kprobes, a pointer to local variable is passed to
debugfs_create_file(); which will go out of scope when the init
function returns. The reason this hasn't triggered random memory
corruption is because the pointer is not accessed during the debugfs
file callbacks.
Since the enabled state is managed by the kprobes_all_disabled global
variable, the local variable is not needed. Fix the incorrect (and
unnecessary) usage of local variable during debugfs_file_create() by
passing NULL instead.
Link: https://lkml.kernel.org/r/163163031686.489837.4476867635937014973.stgit@devnote2
Fixes: bf8f6e5b3e ("Kprobes: The ON/OFF knob thru debugfs")
Signed-off-by: Punit Agrawal <punitagrawal@gmail.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7266dda2f1 ]
Currently a call to snd_card_new that fails will set card with a NULL
pointer, this causes a null pointer dereference on the error cleanup
path when card it passed to snd_card_free. Fix this by adding a new
error exit path that does not call snd_card_free and exiting via this
new path.
Addresses-Coverity: ("Explicit null dereference")
Fixes: 9e44d63246 ("[media] cx23885: Add ALSA support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42bb98e420 ]
The "card" string only holds 31 characters (and the terminating NUL).
In order to avoid truncation, use a shorter card description instead of
the current result, "Trident TVMaster TM5600/6000/60".
Suggested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: e28f49b0b2 ("V4L/DVB: tm6000: fix some info messages")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2908249f38 ]
The "card" string only holds 31 characters (and the terminating NUL).
In order to avoid truncation, use a shorter card description instead of
the current result, "Silicon Labs Si470x FM Radio Re".
Suggested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 78656acdcf ("V4L/DVB (7038): USB radio driver for Silicon Labs Si470x FM Radio Receivers")
Fixes: cc35bbddfe ("V4L/DVB (12416): radio-si470x: add i2c driver for si470x")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dfadec236a ]
The "card" string only holds 31 characters (and the terminating NUL).
In order to avoid truncation, use a shorter card description instead of
the current result, "Texas Instruments Wl1273 FM Rad".
Suggested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 87d1a50ce4 ("[media] V4L2: WL1273 FM Radio: TI WL1273 FM radio driver")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2143ad413c ]
A successful 'clk_prepare()' call should be balanced by a corresponding
'clk_unprepare()' call in the error handling path of the probe, as already
done in the remove function.
Update the error handling path accordingly.
Fixes: 3003a180ef ("[media] VPU: mediatek: support Mediatek VPU")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Houlong Wei <houlong.wei@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48d219f9cc ]
Static analysis reports this representative problem
tda1997x.c:1939: warning: 7th function call argument is an uninitialized
value
The 7th argument is buffer[0], which is set in the earlier call to
io_readn(). When io_readn() call to io_read() fails with the first
read, buffer[0] is not set and 0 is returned and stored in len.
The later call to hdmi_infoframe_unpack()'s size parameter is the
static size of buffer, always 40, so a short read is not caught
in hdmi_infoframe_unpacks()'s checking. The variable len should be
used instead.
Zero initialize buffer to 0 so it is in a known start state.
Fixes: 9ac0038db9 ("media: i2c: Add TDA1997x HDMI receiver driver")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c87ed93574 ]
If the driver does not implement s_ctrl, but it does implement
s_ext_ctrls, we convert the call.
When that happens we have also to convert back the response from
s_ext_ctrls.
Fixes v4l2_compliance:
Control ioctls (Input 0):
fail: v4l2-test-controls.cpp(411): returned control value out of range
fail: v4l2-test-controls.cpp(507): invalid control 00980900
test VIDIOC_G/S_CTRL: FAIL
Fixes: 35ea11ff84 ("V4L/DVB (8430): videodev: move some functions from v4l2-dev.h to v4l2-common.h or v4l2-ioctl.h")
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11b982e950 ]
Currently the null pointer check on dvb_spi->vcc_supply is inverted and
this leads to only null values of the dvb_spi->vcc_supply being passed
to the call of regulator_disable causing null pointer dereferences.
Fix this by only calling regulator_disable if dvb_spi->vcc_supply is
not null.
Addresses-Coverity: ("Dereference after null check")
Fixes: dcb0145821 ("media: cxd2880-spi: Fix an error handling path")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 335aea75b0 ]
The overflow check in amdgpu_bo_list_create() causes a warning with
clang-14 on 64-bit architectures, since the limit can never be
exceeded.
drivers/gpu/drm/amd/amdgpu/amdgpu_bo_list.c:74:18: error: result of comparison of constant 256204778801521549 with expression of type 'unsigned int' is always false [-Werror,-Wtautological-constant-out-of-range-compare]
if (num_entries > (SIZE_MAX - sizeof(struct amdgpu_bo_list))
~~~~~~~~~~~ ^ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The check remains useful for 32-bit architectures, so just avoid the
warning by using size_t as the type for the count.
Fixes: 920990cb08 ("drm/amdgpu: allocate the bo_list array after the list")
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 019edd01d1 ]
On a i.MX-based board with a QCA9377 Wifi chip, the following errors
are seen after launching the 'hostapd' application:
hostapd /etc/wifi.conf
Configuration file: /etc/wifi.conf
wlan0: interface state UNINITIALIZED->COUNTRY_UPDATE
NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!
Using interface wlan0 with hwaddr 00:1f:7b:31:04:a0 and ssid "thessid"
IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
wlan0: interface state COUNTRY_UPDATE->ENABLED
wlan0: AP-ENABLED
NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!
NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!
NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!
NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!
...
Fix this problem by adding the BH locking around napi-schedule(),
in the same way it was done in commit e63052a5dd ("mlx5e: add
add missing BH locking around napi_schdule()").
Its commit log provides the following explanation:
"It's not correct to call napi_schedule() in pure process
context. Because we use __raise_softirq_irqoff() we require
callers to be in a context which will eventually lead to
softirq handling (hardirq, bh disabled, etc.).
With code as is users will see:
NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!
"
Fixes: cfee8793a7 ("ath10k: enable napi on RX path for sdio")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210824144339.2796122-1-festevam@denx.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6dfbc3ba9 ]
When receiving a beacon or probe response, we should update the
boottime_ns field which is the timestamp the frame was received at.
(cf mac80211.h)
This fixes a scanning issue with Android since it relies on this
timestamp to determine when the AP has been seen for the last time
(via the nl80211 BSS_LAST_SEEN_BOOTTIME parameter).
Fixes: 5e3dd157d7 ("ath10k: mac80211 driver for Qualcomm Atheros 802.11ac CQA98xx devices")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1629811733-7927-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1db2b0d0a3 ]
Whenever ath11k is bootup with a user country already set, cfg80211
notifies this country info to ath11k soon after registration, where the
notification is sent to the firmware for fetching the rules of this user
country input.
Multiple race conditions could be seen in this scenario where a new
request is either lost as pointed in [1] or a new regd overwrites the
default regd provided by the firmware during bootup. Note that, the
default regd is used for intersection purpose and hence it should not be
overwritten.
The main reason as pointed by [1] is the usage of ATH11K_FLAG_REGISTERED
flag which is updated after completion of core registration, whereas the
reg notification from cfg80211 and wmi events for the corresponding
request can happen much before that. Since the ATH11K_FLAG_REGISTERED is
currently used to determine if the event containing reg rules belong to
default regd or for user request, there is a possibility of the default
regd getting overwritten.
Since the default reg rules will be received only once per pdev on
firmware load, the above flag based check can be replaced with a check
to see if default_regd is already set, so that we can now always update
the new_regd. Also if the new_regd is set, this will be always used to
update the reg rules for the registered phy.
[1] https://patchwork.kernel.org/project/linux-wireless/patch/1829665.1PRlr7bOQj@ripper/
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01460-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-4-jouni@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aadf7c81a0 ]
The ath11k_dbring_bufs_replenish() and ath11k_dbring_fill_bufs()
take a "gfp" parameter but they since they take spinlocks, the
allocations they do have to be atomic. This causes a bug because
ath11k_dbring_buf_setup passes GFP_KERNEL for the gfp flags.
The fix is to use GFP_ATOMIC and remove the unused parameters.
Fixes: bd6478559e ("ath11k: Add direct buffer ring support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210812070434.GE31863@kili
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f5f12f5d4 ]
The max VLAN number with non-4K VLAN activated is 15, and the
range is 0..15. Not 16.
The impact should be low since we by default have 4K VLAN and
thus have 4095 VLANs to play with in this switch. There will
not be a problem unless the code is rewritten to only use
16 VLANs.
Fixes: d8652956cf ("net: dsa: realtek-smi: Add Realtek SMI driver")
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit acde891c24 ]
Directly using _usecs_to_jiffies() might be unsafe, so it's
better to use usecs_to_jiffies() instead.
Because we can see that the result of _usecs_to_jiffies()
could be larger than MAX_JIFFY_OFFSET values without the
check of the input.
Fixes: c410bf0193 ("Fix the excessive initial retransmission timeout")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f20311cc9c ]
On newer CAAM versions, not all accelerators are disabled if the SoC is
a non-E variant. While the driver checks most of the modules for
availability, there is one - PKHA - which sticks out. On non-E variants
it is still reported as available, that is the number of instances is
non-zero, but it has limited functionality. In particular it doesn't
support encryption and decryption, but just signing and verifying. This
is indicated by a bit in the PKHA_MISC field. Take this bit into account
if we are checking for availability.
This will the following error:
[ 8.167817] caam_jr 8020000.jr: 20000b0f: CCB: desc idx 11: : Invalid CHA selected.
Tested on an NXP LS1028A (non-E) SoC.
Fixes: d239b10d4c ("crypto: caam - add register map changes cf. Era 10")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e5f2d90c2 ]
bdev->evt_skb will get freed in the normal path and one error path
of mtk_hci_wmt_sync, while the other error paths do not free it,
which may cause a memleak. This bug is suggested by a static analysis
tool, please advise.
Fixes: e0b67035a9 ("Bluetooth: mediatek: update the common setup between MT7622 and other devices")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c719fed0f ]
When the BSS reference holds a valid reference, it is not freed. The 'if'
condition is wrong. Instead of the 'if (bss)' check, the 'if (!bss)' check
is used.
The issue is solved by removing the unnecessary 'if' check because
cfg80211_put_bss() already performs the NULL validation.
Fixes: 6cd4fa5ab6 ("staging: wilc1000: make use of cfg80211_inform_bss_frame()")
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-3-ajay.kathat@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 701668d3bf ]
We have been tracking a strange bug with Antenna Diversity Switching (ADS)
on wcn3680b for a while.
ADS is configured like this:
A. Via a firmware configuration table baked into the NV area.
1. Defines if ADS is enabled.
2. Defines which GPIOs are connected to which antenna enable pin.
3. Defines which antenna/GPIO is primary and which is secondary.
B. WCN36XX_CFG_VAL(ANTENNA_DIVERSITY, N)
N is a bitmask of available antenna.
Setting N to 3 indicates a bitmask of enabled antenna (1 | 2).
Obviously then we can set N to 1 or N to 2 to fix to a particular
antenna and disable antenna diversity.
C. WCN36XX_CFG_VAL(ASD_PROBE_INTERVAL, XX)
XX is the number of beacons between each antenna RSSI check.
Setting this value to 50 means, every 50 received beacons, run the
ADS algorithm.
D. WCN36XX_CFG_VAL(ASD_TRIGGER_THRESHOLD, YY)
YY is a two's complement integer which specifies the RSSI decibel
threshold below which ADS will run.
We default to -60db here, meaning a measured RSSI <= -60db will
trigger an ADS probe.
E. WCN36XX_CFG_VAL(ASD_RTT_RSSI_HYST_THRESHOLD, Z)
Z is a hysteresis value, indicating a delta which the RSSI must
exceed for the antenna switch to be valid.
For example if HYST_THRESHOLD == 3 AntennaId1-RSSI == -60db and
AntennaId-2-RSSI == -58db then firmware will not switch antenna.
The threshold needs to be -57db or better to satisfy the criteria.
F. A firmware feature bit also exists ANTENNA_DIVERSITY_SELECTION.
This feature bit is used by the firmware to report if
ANTENNA_DIVERSITY_SELECTION is supported. The host is not required to
toggle this bit to enable or disable ADS.
ADS works like this:
A. Every XX beacons the firmware switches to or remains on the primary
antenna.
B. The firmware then sends a Request-To-Send (RTS) packet to the AP.
C. The firmware waits for a Clear-To-Send (CTS) response from the AP.
D. The firmware then notes the received RSSI on the CTS packet.
E. The firmware then repeats steps A-D on the secondary antenna.
F. Subsequently if the RSSI on the measured antenna is better than
ASD_TRIGGER_THRESHOLD + the active antenna's RSSI then the
measured antenna becomes the active antenna.
G. If RSSI rises past ASD_TRIGGER_THRESHOLD then ADS doesn't run at
all even if there is a substantially better RSSI on the alternative
antenna.
What we have been observing is that the RTS packet is being sent but the
MAC address is a byte-swapped version of the target MAC. The ADS/RTS MAC is
corrupted only when the link is encrypted, if the AP is open the RTS MAC is
correct. Similarly if we configure the firmware to an RTS/CTS sequence for
regular data - the transmitted RTS MAC is correctly formatted.
Internally the wcn36xx firmware uses the indexes in the SMD commands to
populate and extract data from specific entries in an STA lookup table. The
AP's MAC appears a number of times in different indexes within this lookup
table, so the MAC address extracted for the data-transmit RTS and the MAC
address extracted for the ADS/RTS packet are not the same STA table index.
Our analysis indicates the relevant firmware STA table index is
"bssSelfStaIdx".
There is an STA populate function responsible for formatting the MAC
address of the bssSelfStaIdx including byte-swapping the MAC address.
Its clear then that the required STA populate command did not run for
bssSelfStaIdx.
So taking a look at the sequence of SMD commands sent to the firmware we
see the following downstream when moving from an unencrypted to encrypted
BSS setup.
- WLAN_HAL_CONFIG_BSS_REQ
- WLAN_HAL_CONFIG_STA_REQ
- WLAN_HAL_SET_STAKEY_REQ
Upstream in wcn36xx we have
- WLAN_HAL_CONFIG_BSS_REQ
- WLAN_HAL_SET_STAKEY_REQ
The solution then is to add the missing WLAN_HAL_CONFIG_STA_REQ between
WLAN_HAL_CONFIG_BSS_REQ and WLAN_HAL_SET_STAKEY_REQ.
No surprise WLAN_HAL_CONFIG_STA_REQ is the routine responsible for
populating the STA lookup table in the firmware and once done the MAC sent
by the ADS routine is in the correct byte-order.
This bug is apparent with ADS but it is also the case that any other
firmware routine that depends on the "bssSelfStaIdx" would retrieve
malformed data on an encrypted link.
Fixes: 3e977c5c52 ("wcn36xx: Define wcn3680 specific firmware parameters")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Benjamin Li <benl@squareup.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210909144428.2564650-2-bryan.odonoghue@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ee285395b ]
It was found that the following warning was displayed when remounting
controllers from cgroup v2 to v1:
[ 8042.997778] WARNING: CPU: 88 PID: 80682 at kernel/cgroup/cgroup.c:3130 cgroup_apply_control_disable+0x158/0x190
:
[ 8043.091109] RIP: 0010:cgroup_apply_control_disable+0x158/0x190
[ 8043.096946] Code: ff f6 45 54 01 74 39 48 8d 7d 10 48 c7 c6 e0 46 5a a4 e8 7b 67 33 00 e9 41 ff ff ff 49 8b 84 24 e8 01 00 00 0f b7 40 08 eb 95 <0f> 0b e9 5f ff ff ff 48 83 c4 08 5b 5d 41 5c 41 5d 41 5e 41 5f c3
[ 8043.115692] RSP: 0018:ffffba8a47c23d28 EFLAGS: 00010202
[ 8043.120916] RAX: 0000000000000036 RBX: ffffffffa624ce40 RCX: 000000000000181a
[ 8043.128047] RDX: ffffffffa63c43e0 RSI: ffffffffa63c43e0 RDI: ffff9d7284ee1000
[ 8043.135180] RBP: ffff9d72874c5800 R08: ffffffffa624b090 R09: 0000000000000004
[ 8043.142314] R10: ffffffffa624b080 R11: 0000000000002000 R12: ffff9d7284ee1000
[ 8043.149447] R13: ffff9d7284ee1000 R14: ffffffffa624ce70 R15: ffffffffa6269e20
[ 8043.156576] FS: 00007f7747cff740(0000) GS:ffff9d7a5fc00000(0000) knlGS:0000000000000000
[ 8043.164663] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 8043.170409] CR2: 00007f7747e96680 CR3: 0000000887d60001 CR4: 00000000007706e0
[ 8043.177539] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 8043.184673] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 8043.191804] PKRU: 55555554
[ 8043.194517] Call Trace:
[ 8043.196970] rebind_subsystems+0x18c/0x470
[ 8043.201070] cgroup_setup_root+0x16c/0x2f0
[ 8043.205177] cgroup1_root_to_use+0x204/0x2a0
[ 8043.209456] cgroup1_get_tree+0x3e/0x120
[ 8043.213384] vfs_get_tree+0x22/0xb0
[ 8043.216883] do_new_mount+0x176/0x2d0
[ 8043.220550] __x64_sys_mount+0x103/0x140
[ 8043.224474] do_syscall_64+0x38/0x90
[ 8043.228063] entry_SYSCALL_64_after_hwframe+0x44/0xae
It was caused by the fact that rebind_subsystem() disables
controllers to be rebound one by one. If more than one disabled
controllers are originally from the default hierarchy, it means that
cgroup_apply_control_disable() will be called multiple times for the
same default hierarchy. A controller may be killed by css_kill() in
the first round. In the second round, the killed controller may not be
completely dead yet leading to the warning.
To avoid this problem, we collect all the ssid's of controllers that
needed to be disabled from the default hierarchy and then disable them
in one go instead of one by one.
Fixes: 334c3679ec ("cgroup: reimplement rebind_subsystems() using cgroup_apply_control() and friends")
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aed0826b0c ]
The key_domain member in struct net only exists if we define CONFIG_KEYS.
So we should add the define when we used key_domain.
Fixes: 9b24261051 ("keys: Network namespace domain tag")
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2507003a1d ]
lock_is_held_type(, 1) detects acquired read locks. It only recognized
locks acquired with lock_acquire_shared(). Read locks acquired with
lock_acquire_shared_recursive() are not recognized because a `2' is
stored as the read value.
Rework the check to additionally recognise lock's read value one and two
as a read held lock.
Fixes: e918188611 ("locking: More accurate annotations for read_lock()")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Boqun Feng <boqun.feng@gmail.com>
Acked-by: Waiman Long <longman@redhat.com>
Link: https://lkml.kernel.org/r/20210903084001.lblecrvz4esl4mrr@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4f8681911 ]
The hardware sets the TMUWCF bit back to 0 when the TMU write
combiner flush completes so we should be checking for that instead
of the L2TFLS bit.
v2 (Melissa Wen):
- Add Signed-off-by and Fixes tags.
- Change the error message for the timeout to be more clear.
Fixes spurious Vulkan CTS failures in:
dEQP-VK.binding_model.descriptorset_random.*
Fixes: d223f98f02 ("drm/v3d: Add support for compute shader dispatch.")
Signed-off-by: Iago Toral Quiroga <itoral@igalia.com>
Reviewed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210915100507.3945-1-itoral@igalia.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9af9dcf11b ]
The asm_cpu_bringup_and_idle() function is required to push the return
value on the stack in order to make ORC happy, but the only reason
objtool doesn't complain is because of a happy accident.
The thing is that asm_cpu_bringup_and_idle() doesn't return, so
validate_branch() never terminates and falls through to the next
function, which in the normal case is the hypercall_page. And that, as
it happens, is 4095 NOPs and a RET.
Make asm_cpu_bringup_and_idle() terminate on it's own, by making the
function it calls as a dead-end. This way we no longer rely on what
code happens to come after.
Fixes: c3881eb58d ("x86/xen: Make the secondary CPU idle tasks reliable")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Link: https://lore.kernel.org/r/20210624095147.693801717@infradead.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ad74d39c5 ]
The current definition of 2W burst length is invalid.
This patch fixes it. Current downstream DEU driver doesn't
use DMA. An incorrect burst length value doesn't cause any
errors. This patch also adds other burst length values.
Fixes: dfec1a827d ("MIPS: Lantiq: Add DMA support")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f0b2b2df54 ]
The sync_sched_exp_online_cleanup() checks to see if RCU needs
an expedited quiescent state from the incoming CPU, sending it
an IPI if so. Before sending IPI, it checks whether expedited
qs need has been already requested for the incoming CPU, by
checking rcu_data.cpu_no_qs.b.exp for the current cpu, on which
sync_sched_exp_online_cleanup() is running. This works for the
case where incoming CPU is same as self. However, for the case
where incoming CPU is different from self, expedited request
won't get marked, which can potentially delay reporting of
expedited quiescent state for the incoming CPU.
Fixes: e015a34112 ("rcu: Avoid self-IPI in sync_sched_exp_online_cleanup()")
Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49d8a56064 ]
Before freeing struct sco_conn, all delayed timeout work should be
cancelled. Otherwise, sco_sock_timeout could potentially use the
sco_conn after it has been freed.
Additionally, sco_conn.timeout_work should be initialized when the
connection is allocated, not when the channel is added. This is
because an sco_conn can create channels with multiple sockets over its
lifetime, which happens if sockets are released but the connection
isn't deleted.
Fixes: ba316be1b6 ("Bluetooth: schedule SCO timeouts with delayed_work")
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7b1d02fc4 ]
The internal stream state sets the timeout to 120 seconds 2 seconds
after the creation of the flow, attach this internal stream state to the
IPS_ASSURED flag for consistent event reporting.
Before this patch:
[NEW] udp 17 30 src=10.246.11.13 dst=216.239.35.0 sport=37282 dport=123 [UNREPLIED] src=216.239.35.0 dst=10.246.11.13 sport=123 dport=37282
[UPDATE] udp 17 30 src=10.246.11.13 dst=216.239.35.0 sport=37282 dport=123 src=216.239.35.0 dst=10.246.11.13 sport=123 dport=37282
[UPDATE] udp 17 30 src=10.246.11.13 dst=216.239.35.0 sport=37282 dport=123 src=216.239.35.0 dst=10.246.11.13 sport=123 dport=37282 [ASSURED]
[DESTROY] udp 17 src=10.246.11.13 dst=216.239.35.0 sport=37282 dport=123 src=216.239.35.0 dst=10.246.11.13 sport=123 dport=37282 [ASSURED]
Note IPS_ASSURED for the flow not yet in the internal stream state.
after this update:
[NEW] udp 17 30 src=10.246.11.13 dst=216.239.35.0 sport=37282 dport=123 [UNREPLIED] src=216.239.35.0 dst=10.246.11.13 sport=123 dport=37282
[UPDATE] udp 17 30 src=10.246.11.13 dst=216.239.35.0 sport=37282 dport=123 src=216.239.35.0 dst=10.246.11.13 sport=123 dport=37282
[UPDATE] udp 17 120 src=10.246.11.13 dst=216.239.35.0 sport=37282 dport=123 src=216.239.35.0 dst=10.246.11.13 sport=123 dport=37282 [ASSURED]
[DESTROY] udp 17 src=10.246.11.13 dst=216.239.35.0 sport=37282 dport=123 src=216.239.35.0 dst=10.246.11.13 sport=123 dport=37282 [ASSURED]
Before this patch, short-lived UDP flows never entered IPS_ASSURED, so
they were already candidate flow to be deleted by early_drop under
stress.
Before this patch, IPS_ASSURED is set on regardless the internal stream
state, attach this internal stream state to IPS_ASSURED.
packet #1 (original direction) enters NEW state
packet #2 (reply direction) enters ESTABLISHED state, sets on IPS_SEEN_REPLY
paclet #3 (any direction) sets on IPS_ASSURED (if 2 seconds since the
creation has passed by).
Reported-by: Maciej Żenczykowski <zenczykowski@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66e29fcda1 ]
With idle polling, IPIs are not sent when a CPU idle, but queued
and run later from do_idle(). The default kgdb_call_nmi_hook()
implementation gets the pointer to struct pt_regs from get_irq_reqs(),
which doesn't work in that case because it was not called from the
IPI interrupt handler. Fix it by defining our own kgdb_roundup()
function which sents an IPI_ENTER_KGDB. When that IPI is received
on the target CPU kgdb_nmicallback() is called.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e0ba125c2 ]
With 64 bit kernels unwind_special() is not working because
it compares the pc to the address of the function descriptor.
Add a helper function that compares pc with the dereferenced
address. This fixes all of the backtraces on my c8000. Without
this changes, a lot of backtraces are missing in kdb or the
show-all-tasks command from /proc/sysrq-trigger.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9cc2fa4f4a ]
The function end_of_stack() returns a pointer to the last entry of a
stack. For architectures like parisc where the stack grows upwards
return the pointer to the highest address in the stack.
Without this change I faced a crash on parisc, because the stackleak
functionality wrote STACKLEAK_POISON to the lowest address and thus
overwrote the first 4 bytes of the task_struct which included the
TIF_FLAGS.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f35dcaa0a8 ]
close_range() test type conflicts with close_range() library call in
x86_64-linux-gnu/bits/unistd_ext.h. Fix it by changing the name to
core_close_range().
gcc -g -I../../../../usr/include/ close_range_test.c -o ../tools/testing/selftests/core/close_range_test
In file included from close_range_test.c:16:
close_range_test.c:57:6: error: conflicting types for ‘close_range’; have ‘void(struct __test_metadata *)’
57 | TEST(close_range)
| ^~~~~~~~~~~
../kselftest_harness.h:181:21: note: in definition of macro ‘__TEST_IMPL’
181 | static void test_name(struct __test_metadata *_metadata); \
| ^~~~~~~~~
close_range_test.c:57:1: note: in expansion of macro ‘TEST’
57 | TEST(close_range)
| ^~~~
In file included from /usr/include/unistd.h:1204,
from close_range_test.c:13:
/usr/include/x86_64-linux-gnu/bits/unistd_ext.h:56:12: note: previous declaration of ‘close_range’ with type ‘int(unsigned int, unsigned int, int)’
56 | extern int close_range (unsigned int __fd, unsigned int __max_fd,
| ^~~~~~~~~~~
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 285f68afa8 ]
The following issue is observed with CONFIG_DEBUG_PREEMPT when KVM loads:
KVM: vmx: using Hyper-V Enlightened VMCS
BUG: using smp_processor_id() in preemptible [00000000] code: systemd-udevd/488
caller is set_hv_tscchange_cb+0x16/0x80
CPU: 1 PID: 488 Comm: systemd-udevd Not tainted 5.15.0-rc5+ #396
Hardware name: Microsoft Corporation Virtual Machine/Virtual Machine, BIOS Hyper-V UEFI Release v4.0 12/17/2019
Call Trace:
dump_stack_lvl+0x6a/0x9a
check_preemption_disabled+0xde/0xe0
? kvm_gen_update_masterclock+0xd0/0xd0 [kvm]
set_hv_tscchange_cb+0x16/0x80
kvm_arch_init+0x23f/0x290 [kvm]
kvm_init+0x30/0x310 [kvm]
vmx_init+0xaf/0x134 [kvm_intel]
...
set_hv_tscchange_cb() can get preempted in between acquiring
smp_processor_id() and writing to HV_X64_MSR_REENLIGHTENMENT_CONTROL. This
is not an issue by itself: HV_X64_MSR_REENLIGHTENMENT_CONTROL is a
partition-wide MSR and it doesn't matter which particular CPU will be
used to receive reenlightenment notifications. The only real problem can
(in theory) be observed if the CPU whose id was acquired with
smp_processor_id() goes offline before we manage to write to the MSR,
the logic in hv_cpu_die() won't be able to reassign it correctly.
Reported-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Link: https://lore.kernel.org/r/20211012155005.1613352-1-vkuznets@redhat.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a27ca3947 ]
For packets originating from hardware scan, the channel and band is
included in the buffer descriptor (bd->rf_band & bd->rx_ch).
For 2Ghz band the channel value is directly reported in the 4-bit
rx_ch field. For 5Ghz band, the rx_ch field contains a mapping
index (given the 4-bit limitation).
The reserved0 value field is also used to extend 4-bit mapping to
5-bit mapping to support more than 16 5Ghz channels.
This change adds correct reporting of the frequency/band, that is
used in scan mechanism. And is required for 5Ghz hardware scan
support.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634554678-7993-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ef9dc0f14 ]
We got the following lockdep splat while running fstests (specifically
btrfs/003 and btrfs/020 in a row) with the new rc. This was uncovered
by 87579e9b7d ("loop: use worker per cgroup instead of kworker") which
converted loop to using workqueues, which comes with lockdep
annotations that don't exist with kworkers. The lockdep splat is as
follows:
WARNING: possible circular locking dependency detected
5.14.0-rc2-custom+ #34 Not tainted
------------------------------------------------------
losetup/156417 is trying to acquire lock:
ffff9c7645b02d38 ((wq_completion)loop0){+.+.}-{0:0}, at: flush_workqueue+0x84/0x600
but task is already holding lock:
ffff9c7647395468 (&lo->lo_mutex){+.+.}-{3:3}, at: __loop_clr_fd+0x41/0x650 [loop]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #5 (&lo->lo_mutex){+.+.}-{3:3}:
__mutex_lock+0xba/0x7c0
lo_open+0x28/0x60 [loop]
blkdev_get_whole+0x28/0xf0
blkdev_get_by_dev.part.0+0x168/0x3c0
blkdev_open+0xd2/0xe0
do_dentry_open+0x163/0x3a0
path_openat+0x74d/0xa40
do_filp_open+0x9c/0x140
do_sys_openat2+0xb1/0x170
__x64_sys_openat+0x54/0x90
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
-> #4 (&disk->open_mutex){+.+.}-{3:3}:
__mutex_lock+0xba/0x7c0
blkdev_get_by_dev.part.0+0xd1/0x3c0
blkdev_get_by_path+0xc0/0xd0
btrfs_scan_one_device+0x52/0x1f0 [btrfs]
btrfs_control_ioctl+0xac/0x170 [btrfs]
__x64_sys_ioctl+0x83/0xb0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
-> #3 (uuid_mutex){+.+.}-{3:3}:
__mutex_lock+0xba/0x7c0
btrfs_rm_device+0x48/0x6a0 [btrfs]
btrfs_ioctl+0x2d1c/0x3110 [btrfs]
__x64_sys_ioctl+0x83/0xb0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
-> #2 (sb_writers#11){.+.+}-{0:0}:
lo_write_bvec+0x112/0x290 [loop]
loop_process_work+0x25f/0xcb0 [loop]
process_one_work+0x28f/0x5d0
worker_thread+0x55/0x3c0
kthread+0x140/0x170
ret_from_fork+0x22/0x30
-> #1 ((work_completion)(&lo->rootcg_work)){+.+.}-{0:0}:
process_one_work+0x266/0x5d0
worker_thread+0x55/0x3c0
kthread+0x140/0x170
ret_from_fork+0x22/0x30
-> #0 ((wq_completion)loop0){+.+.}-{0:0}:
__lock_acquire+0x1130/0x1dc0
lock_acquire+0xf5/0x320
flush_workqueue+0xae/0x600
drain_workqueue+0xa0/0x110
destroy_workqueue+0x36/0x250
__loop_clr_fd+0x9a/0x650 [loop]
lo_ioctl+0x29d/0x780 [loop]
block_ioctl+0x3f/0x50
__x64_sys_ioctl+0x83/0xb0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
other info that might help us debug this:
Chain exists of:
(wq_completion)loop0 --> &disk->open_mutex --> &lo->lo_mutex
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&lo->lo_mutex);
lock(&disk->open_mutex);
lock(&lo->lo_mutex);
lock((wq_completion)loop0);
*** DEADLOCK ***
1 lock held by losetup/156417:
#0: ffff9c7647395468 (&lo->lo_mutex){+.+.}-{3:3}, at: __loop_clr_fd+0x41/0x650 [loop]
stack backtrace:
CPU: 8 PID: 156417 Comm: losetup Not tainted 5.14.0-rc2-custom+ #34
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
Call Trace:
dump_stack_lvl+0x57/0x72
check_noncircular+0x10a/0x120
__lock_acquire+0x1130/0x1dc0
lock_acquire+0xf5/0x320
? flush_workqueue+0x84/0x600
flush_workqueue+0xae/0x600
? flush_workqueue+0x84/0x600
drain_workqueue+0xa0/0x110
destroy_workqueue+0x36/0x250
__loop_clr_fd+0x9a/0x650 [loop]
lo_ioctl+0x29d/0x780 [loop]
? __lock_acquire+0x3a0/0x1dc0
? update_dl_rq_load_avg+0x152/0x360
? lock_is_held_type+0xa5/0x120
? find_held_lock.constprop.0+0x2b/0x80
block_ioctl+0x3f/0x50
__x64_sys_ioctl+0x83/0xb0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f645884de6b
Usually the uuid_mutex exists to protect the fs_devices that map
together all of the devices that match a specific uuid. In rm_device
we're messing with the uuid of a device, so it makes sense to protect
that here.
However in doing that it pulls in a whole host of lockdep dependencies,
as we call mnt_may_write() on the sb before we grab the uuid_mutex, thus
we end up with the dependency chain under the uuid_mutex being added
under the normal sb write dependency chain, which causes problems with
loop devices.
We don't need the uuid mutex here however. If we call
btrfs_scan_one_device() before we scratch the super block we will find
the fs_devices and not find the device itself and return EBUSY because
the fs_devices is open. If we call it after the scratch happens it will
not appear to be a valid btrfs file system.
We do not need to worry about other fs_devices modifying operations here
because we're protected by the exclusive operations locking.
So drop the uuid_mutex here in order to fix the lockdep splat.
A more detailed explanation from the discussion:
We are worried about rm and scan racing with each other, before this
change we'll zero the device out under the UUID mutex so when scan does
run it'll make sure that it can go through the whole device scan thing
without rm messing with us.
We aren't worried if the scratch happens first, because the result is we
don't think this is a btrfs device and we bail out.
The only case we are concerned with is we scratch _after_ scan is able
to read the superblock and gets a seemingly valid super block, so lets
consider this case.
Scan will call device_list_add() with the device we're removing. We'll
call find_fsid_with_metadata_uuid() and get our fs_devices for this
UUID. At this point we lock the fs_devices->device_list_mutex. This is
what protects us in this case, but we have two cases here.
1. We aren't to the device removal part of the RM. We found our device,
and device name matches our path, we go down and we set total_devices
to our super number of devices, which doesn't affect anything because
we haven't done the remove yet.
2. We are past the device removal part, which is protected by the
device_list_mutex. Scan doesn't find the device, it goes down and
does the
if (fs_devices->opened)
return -EBUSY;
check and we bail out.
Nothing about this situation is ideal, but the lockdep splat is real,
and the fix is safe, tho admittedly a bit scary looking.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ copy more from the discussion ]
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44bee215f7 ]
Fix a warning reported by smatch that ret could be returned without
initialized. The dedupe operations are supposed to to return 0 for a 0
length range but the caller does not pass olen == 0. To keep this
behaviour and also fix the warning initialize ret to 0.
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Sidong Yang <realwakka@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d730ee686 ]
Let GK45 not go into BIOS for determining the AC power state.
The BIOS wrongly returns 0, so hardcode the power state to 1.
The mini PC GK45 by Besstar Tech Lld. (aka Kodlix) just runs
off AC. It does not include any batteries. Nevertheless BIOS
reports AC off:
root@kodlix:/usr/src/linux# cat /sys/class/power_supply/ADP1/online
0
root@kodlix:/usr/src/linux# modprobe acpi_dbg
root@kodlix:/usr/src/linux# tools/power/acpi/acpidbg
- find _PSR
\_SB.PCI0.SBRG.H_EC.ADP1._PSR Method 000000009283cee8 001 Args 0 Len 001C Aml 00000000f54e5f67
- execute \_SB.PCI0.SBRG.H_EC.ADP1._PSR
Evaluating \_SB.PCI0.SBRG.H_EC.ADP1._PSR
Evaluation of \_SB.PCI0.SBRG.H_EC.ADP1._PSR returned object 00000000dc08c187, external buffer length 18
[Integer] = 0000000000000000
that should be
[Integer] = 0000000000000001
Signed-off-by: Stefan Schaeckeler <schaecsn@gmx.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c9c296adf ]
The VRF driver invokes netfilter for output+postrouting hooks so that users
can create rules that check for 'oif $vrf' rather than lower device name.
This is a problem when NAT rules are configured.
To avoid any conntrack involvement in round 1, tag skbs as 'untracked'
to prevent conntrack from picking them up.
This gets cleared before the packet gets handed to the ip stack so
conntrack will be active on the second iteration.
One remaining issue is that a rule like
output ... oif $vrfname notrack
won't propagate to the second round because we can't tell
'notrack set via ruleset' and 'notrack set by vrf driver' apart.
However, this isn't a regression: the 'notrack' removal happens
instead of unconditional nf_reset_ct().
I'd also like to avoid leaking more vrf specific conditionals into the
netfilter infra.
For ingress, conntrack has already been done before the packet makes it
to the vrf driver, with this patch egress does connection tracking with
lower/physical device as well.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 345dac33f5 ]
When configuring the kernel for big-endian, we set either BE-8 or BE-32
based on the CPU architecture level. Until linux-4.4, we did not have
any ARMv7-M platform allowing big-endian builds, but now i.MX/Vybrid
is in that category, adn we get a build error because of this:
arch/arm/kernel/module-plts.c: In function 'get_module_plt':
arch/arm/kernel/module-plts.c:60:46: error: implicit declaration of function '__opcode_to_mem_thumb32' [-Werror=implicit-function-declaration]
This comes down to picking the wrong default, ARMv7-M uses BE8
like ARMv7-A does. Changing the default gets the kernel to compile
and presumably works.
https://lore.kernel.org/all/1455804123-2526139-2-git-send-email-arnd@arndb.de/
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7427f3bb49 ]
So far, glock_hash_walk took a reference on each glock it iterated over, and it
was the examiner's responsibility to drop those references. Dropping the final
reference to a glock can sleep and the examiners are called in a RCU critical
section with spin locks held, so examiners that didn't need the extra reference
had to drop it asynchronously via gfs2_glock_queue_put or similar. This wasn't
done correctly in thaw_glock which did call gfs2_glock_put, and not at all in
dump_glock_func.
Change glock_hash_walk to not take glock references at all. That way, the
examiners that don't need them won't have to bother with slow asynchronous
puts, and the examiners that do need references can take them themselves.
Reported-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 486408d690 ]
In gfs2_inode_lookup and gfs2_create_inode, we're calling
gfs2_cancel_delete_work which currently cancels any remote delete work
(delete_work_func) synchronously. This means that if the work is
currently running, it will wait for it to finish. We're doing this to
pevent a previous instance of an inode from having any influence on the
next instance.
However, delete_work_func uses gfs2_inode_lookup internally, and we can
end up in a deadlock when delete_work_func gets interrupted at the wrong
time. For example,
(1) An inode's iopen glock has delete work queued, but the inode
itself has been evicted from the inode cache.
(2) The delete work is preempted before reaching gfs2_inode_lookup.
(3) Another process recreates the inode (gfs2_create_inode). It tries
to cancel any outstanding delete work, which blocks waiting for
the ongoing delete work to finish.
(4) The delete work calls gfs2_inode_lookup, which blocks waiting for
gfs2_create_inode to instantiate and unlock the new inode =>
deadlock.
It turns out that when the delete work notices that its inode has been
re-instantiated, it will do nothing. This means that it's safe to
cancel the delete work asynchronously. This prevents the kind of
deadlock described above.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61e18ce734 ]
When addr_gen_mode is set to IN6_ADDR_GEN_MODE_NONE, the link-local addr
should not be generated. But it isn't the case for GRE (as well as GRE6)
and SIT tunnels. Make it so that tunnels consider the addr_gen_mode,
especially for IN6_ADDR_GEN_MODE_NONE.
Do this in add_v4_addrs() to cover both GRE and SIT only if the addr
scope is link.
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Acked-by: Antonio Quartulli <a@unstable.cc>
Link: https://lore.kernel.org/r/20211020200618.467342-1-ssuryaextr@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3ea5d56f2 ]
Currently the stacktrace on clang compiled arm kernel uses the 'lr'
register to find the first frame address from pt_regs. However, that
is wrong after calling another function, because the 'lr' register
is used by 'bl' instruction and never be recovered.
As same as gcc arm kernel, directly use the frame pointer (r11) of
the pt_regs to find the first frame address.
Note that this fixes kretprobe stacktrace issue only with
CONFIG_UNWINDER_FRAME_POINTER=y. For the CONFIG_UNWINDER_ARM,
we need another fix.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3867ab592 ]
get_warnings_count() does fclose() using File * returned from popen().
Fix it to call pclose() as it should.
tools/testing/selftests/kvm/x86_64/mmio_warning_test
x86_64/mmio_warning_test.c: In function ‘get_warnings_count’:
x86_64/mmio_warning_test.c:87:9: warning: ‘fclose’ called on pointer returned from a mismatched allocation function [-Wmismatched-dealloc]
87 | fclose(f);
| ^~~~~~~~~
x86_64/mmio_warning_test.c:84:13: note: returned from ‘popen’
84 | f = popen("dmesg | grep \"WARNING:\" | wc -l", "r");
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b81a5f015 ]
When reading the partition table on initial scan hits an I/O error the
I/O will hang with the scan_mutex held:
[<0>] do_read_cache_page+0x49b/0x790
[<0>] read_part_sector+0x39/0xe0
[<0>] read_lba+0xf9/0x1d0
[<0>] efi_partition+0xf1/0x7f0
[<0>] bdev_disk_changed+0x1ee/0x550
[<0>] blkdev_get_whole+0x81/0x90
[<0>] blkdev_get_by_dev+0x128/0x2e0
[<0>] device_add_disk+0x377/0x3c0
[<0>] nvme_mpath_set_live+0x130/0x1b0 [nvme_core]
[<0>] nvme_mpath_add_disk+0x150/0x160 [nvme_core]
[<0>] nvme_alloc_ns+0x417/0x950 [nvme_core]
[<0>] nvme_validate_or_alloc_ns+0xe9/0x1e0 [nvme_core]
[<0>] nvme_scan_work+0x168/0x310 [nvme_core]
[<0>] process_one_work+0x231/0x420
and trying to delete the controller will deadlock as it tries to grab
the scan mutex:
[<0>] nvme_mpath_clear_ctrl_paths+0x25/0x80 [nvme_core]
[<0>] nvme_remove_namespaces+0x31/0xf0 [nvme_core]
[<0>] nvme_do_delete_ctrl+0x4b/0x80 [nvme_core]
As we're now properly ordering the namespace list there is no need to
hold the scan_mutex in nvme_mpath_clear_ctrl_paths() anymore.
And we always need to kick the requeue list as the path will be marked
as unusable and I/O will be requeued _without_ a current path.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2351ead99c ]
When removing a port, all its controllers are being removed, but there
are queues on the port that doesn't belong to any controller (during
connection time). This causes a use-after-free bug for any command
that dereferences req->port (like in nvmet_alloc_ctrl). Those queues
should be destroyed before freeing the port via configfs. Destroy
the remaining queues after the accept_work was cancelled guarantees
that no new queue will be created.
Signed-off-by: Israel Rukshin <israelr@nvidia.com>
Reviewed-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fcf73a804c ]
When removing a port, all its controllers are being removed, but there
are queues on the port that doesn't belong to any controller (during
connection time). This causes a use-after-free bug for any command
that dereferences req->port (like in nvmet_alloc_ctrl). Those queues
should be destroyed before freeing the port via configfs. Destroy the
remaining queues after the RDMA-CM was destroyed guarantees that no
new queue will be created.
Signed-off-by: Israel Rukshin <israelr@nvidia.com>
Reviewed-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3e19dcc4c ]
When a port is removed through configfs, any connected controllers
are starting teardown flow asynchronously and can still send commands.
This causes a use-after-free bug for any command that dereferences
req->port (like in nvmet_parse_io_cmd).
To fix this, wait for all the teardown scheduled works to complete
(like release_work at rdma/tcp drivers). This ensures there are no
active controllers when the port is eventually removed.
Signed-off-by: Israel Rukshin <israelr@nvidia.com>
Reviewed-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ecda6393d ]
The mailbox is initialized after the interrupt handler is installed. As
the firmware is loaded and started even later, it should not happen that
the interrupt occurs without the mailbox being initialized.
As the Linux Driver Verification project (linuxtesting.org) keeps
reporting this as an error, add a check to ignore interrupts before the
mailbox is initialized to fix this potential null pointer dereference.
Reported-by: Yuri Savinykh <s02190703@gse.cs.msu.ru>
Reported-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 037057a5a9 ]
This check is meant to catch cases where a requeue is attempted on a
request that is still inserted. It's never really been useful to catch any
misuse, and now it's actively wrong. Outside of that, this should not be a
BUG_ON() to begin with.
Remove the check as it's now causing active harm, as requeue off the plug
path will trigger it even though the request state is just fine.
Reported-by: Yi Zhang <yi.zhang@redhat.com>
Link: https://lore.kernel.org/linux-block/CAHj4cs80zAUc2grnCZ015-2Rvd-=gXRfB_dFKy=RTm+wRo09HQ@mail.gmail.com/
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ce1bb83a1 ]
If CONFIG_CFI_CLANG=y, attempting to read an event histogram will cause
the kernel to panic due to failed CFI check.
1. echo 'hist:keys=common_pid' >> events/sched/sched_switch/trigger
2. cat events/sched/sched_switch/hist
3. kernel panics on attempting to read hist
This happens because the sort() function expects a generic
int (*)(const void *, const void *) pointer for the compare function.
To prevent this CFI failure, change tracing map cmp_entries_* function
signatures to match this.
Also, fix the build error reported by the kernel test robot [1].
[1] https://lore.kernel.org/r/202110141140.zzi4dRh4-lkp@intel.com/
Link: https://lkml.kernel.org/r/20211014045217.3265162-1-kaleshsingh@google.com
Signed-off-by: Kalesh Singh <kaleshsingh@google.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d25302e465 ]
Some unfriendly component, such as dpdk, write the same mask to
unbound kworker cpumask again and again. Every time it write to
this interface some work is queue to cpu, even though the mask
is same with the original mask.
So, fix it by return success and do nothing if the cpumask is
equal with the old one.
Signed-off-by: Mengen Sun <mengensun@tencent.com>
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f8d7abaa4 ]
This might matter, for example, if the underlying type of enum xz_check
was a signed char. In such a case the validation wouldn't have caught an
unsupported header. I don't know if this problem can occur in the kernel
on any arch but it's still good to fix it because some people might copy
the XZ code to their own projects from Linux instead of the upstream
XZ Embedded repository.
This change may increase the code size by a few bytes. An alternative
would have been to use an unsigned int instead of enum xz_check but
using an enumeration looks cleaner.
Link: https://lore.kernel.org/r/20211010213145.17462-3-xiang@kernel.org
Signed-off-by: Lasse Collin <lasse.collin@tukaani.org>
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83d3c4f22a ]
With valid files, the safety margin described in lib/decompress_unxz.c
ensures that these buffers cannot overlap. But if the uncompressed size
of the input is larger than the caller thought, which is possible when
the input file is invalid/corrupt, the buffers can overlap. Obviously
the result will then be garbage (and usually the decoder will return
an error too) but no other harm will happen when such an over-run occurs.
This change only affects uncompressed LZMA2 chunks and so this
should have no effect on performance.
Link: https://lore.kernel.org/r/20211010213145.17462-2-xiang@kernel.org
Signed-off-by: Lasse Collin <lasse.collin@tukaani.org>
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b9e2291e3 ]
When the in memory flag is changed, we need to persist the change in the
rdev superblock flags. This is needed for "writemostly" and "failfast".
Reviewed-by: Li Feng <fengli@smartx.com>
Signed-off-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba0ffdd8ce ]
Particularly for NVMe with efficient deferred submission for many
requests, there are nice benefits to be seen by bumping the default max
plug count from 16 to 32. This is especially true for virtualized setups,
where the submit part is more expensive. But can be noticed even on
native hardware.
Reduce the multiple queue factor from 4 to 2, since we're changing the
default size.
While changing it, move the defines into the block layer private header.
These aren't values that anyone outside of the block layer uses, or
should use.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 67ca5159db ]
It seems reasonable to fine-tune only some of the skew values when using
one of the rgmii-*id PHY modes, and even when all skew values are
specified, using the correct ID PHY mode makes sense for documentation
purposes. Such a configuration also appears in the binding docs in
Documentation/devicetree/bindings/net/micrel-ksz90x1.txt, so the driver
should not warn about it.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20211012103402.21438-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2835f327bd ]
Some buggy firmware and/or brand new batteries can support a charge that's
slightly over the reported design capacity. In such cases, the kernel will
report to userspace that the charging state of the battery is "Unknown",
when in reality the battery charge is "Full", at least from the design
capacity point of view. Make the fallback condition accepts capacities
over the designed capacity so userspace knows that is full.
Signed-off-by: André Almeida <andrealmeid@collabora.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 814a66741b ]
Both iov_iter_get_pages and iov_iter_get_pages_alloc return the number
of bytes of the iovec they could get the pages for. When they cannot
get any pages, they're supposed to return 0, but when the start of the
iovec isn't page aligned, the calculation goes wrong and they return a
negative value. Fix both functions.
In addition, change iov_iter_get_pages_alloc to return NULL in that case
to prevent resource leaks.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8105c2abbf ]
The issue happens in several error handling paths on two refcounted
object related to the object "host" (dma_chan_rx, dma_chan_tx). In
these paths, the function forgets to decrement one or both objects'
reference count increased earlier by dma_request_chan(), causing
reference count leaks.
Fix it by balancing the refcounts of both objects in some error
handling paths. In correspondence with the changes in moxart_probe(),
IS_ERR() is replaced with IS_ERR_OR_NULL() in moxart_remove() as well.
Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn>
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Link: https://lore.kernel.org/r/20211009041918.28419-1-xiongx18@fudan.edu.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b6012a783 ]
kzalloc() is used to allocate memory for cd->detectors, and if it fails,
channel_detector_exit() behind the label fail will be called:
channel_detector_exit(dpd, cd);
In channel_detector_exit(), cd->detectors is dereferenced through:
struct pri_detector *de = cd->detectors[i];
To fix this possible null-pointer dereference, check cd->detectors before
the for loop to dereference cd->detectors.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Tuo Li <islituo@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210805153854.154066-1-islituo@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49d67e4457 ]
The tracefs file system is by default mounted such that only root user can
access it. But there are legitimate reasons to create a group and allow
those added to the group to have access to tracing. By changing the
permissions of the tracefs mount point to allow access, it will allow
group access to the tracefs directory.
There should not be any real reason to allow all access to the tracefs
directory as it contains sensitive information. Have the default
permission of directories being created not have any OTH (other) bits set,
such that an admin that wants to give permission to a group has to first
disable all OTH bits in the file system.
Link: https://lkml.kernel.org/r/20210818153038.664127804@goodmis.org
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 146e5e7333 ]
Due to deadlocks in the networking subsystem spotted 12 years ago[1],
a workaround was put in place[2] to avoid taking the rtnl lock when it
was not available and restarting the syscall (back to VFS, letting
userspace spin). The following construction is found a lot in the net
sysfs and sysctl code:
if (!rtnl_trylock())
return restart_syscall();
This can be problematic when multiple userspace threads use such
interfaces in a short period, making them to spin a lot. This happens
for example when adding and moving virtual interfaces: userspace
programs listening on events, such as systemd-udevd and NetworkManager,
do trigger actions reading files in sysfs. It gets worse when a lot of
virtual interfaces are created concurrently, say when creating
containers at boot time.
Returning early without hitting the above pattern when the syscall will
fail eventually does make things better. While it is not a fix for the
issue, it does ease things.
[1] https://lore.kernel.org/netdev/49A4D5D5.5090602@trash.net/https://lore.kernel.org/netdev/m14oyhis31.fsf@fess.ebiederm.org/
and https://lore.kernel.org/netdev/20090226084924.16cb3e08@nehalam/
[2] Rightfully, those deadlocks are *hard* to solve.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea2b9a3371 ]
bus_info field had a different value for the media entity and the video
device.
Fixes v4l2-compliance:
v4l2-compliance.cpp(637): media bus_info 'PCI:0000:00:05.0' differs from
V4L2 bus_info 'PCI:viewfinder'
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 553481e380 ]
For a try_fmt call, the node noes not need to be enabled.
Fixes v4l2-compliance
fail: v4l2-test-formats.cpp(717): Video Output Multiplanar is valid, but
no TRY_FMT was implemented
test VIDIOC_TRY_FMT: FAIL
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3c4b6f64a ]
ACPICA commit 0762982923f95eb652cf7ded27356b247c9774de
During wakeup from system-wide sleep states, acpi_get_sleep_type_data()
is called and it tries to get memory from the slab allocator in order
to evaluate a control method, but if KFENCE is enabled in the kernel,
the memory allocation attempt causes an IRQ work to be queued and a
self-IPI to be sent to the CPU running the code which requires the
memory controller to be ready, so if that happens too early in the
wakeup path, it doesn't work.
Prevent that from taking place by calling acpi_get_sleep_type_data()
for S0 upfront, when preparing to enter a given sleep state, and
saving the data obtained by it for later use during system wakeup.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214271
Reported-by: Reik Keutterling <spielkind@gmail.com>
Tested-by: Reik Keutterling <spielkind@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a130e8fbc7 ]
/proc/uptime reports idle time by reading the CPUTIME_IDLE field from
the per-cpu kcpustats. However, on NO_HZ systems, idle time is not
continually updated on idle cpus, leading this value to appear
incorrectly small.
/proc/stat performs an accounting update when reading idle time; we
can use the same approach for uptime.
With this patch, /proc/stat and /proc/uptime now agree on idle time.
Additionally, the following shows idle time tick up consistently on an
idle machine:
(while true; do cat /proc/uptime; sleep 1; done) | awk '{print $2-prev; prev=$2}'
Reported-by: Luigi Rizzo <lrizzo@google.com>
Signed-off-by: Josh Don <joshdon@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lkml.kernel.org/r/20210827165438.3280779-1-joshdon@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b36eb5e7b7 ]
Don't do kfree or other risky things when oops_in_progress is set.
It's easy enough to avoid doing them
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc41665498 ]
If rcsi2_code_to_fmt() return NULL, then null pointer dereference occurs
in the next cycle. That should not be possible now but adding checking
protects from future bugs.
The patch adds checking if format is NULL.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49c3eb3036 ]
The Cyberbook T116 tablet contains quite generic names in the sys_vendor
and product_name DMI strings, without this patch brcmfmac will try to load:
"brcmfmac43455-sdio.Default string-Default string.txt" as nvram file which
is way too generic.
The nvram file shipped on the factory Android image contains the exact
same settings as those used on the AcePC T8 mini PC, so point the new
DMI nvram filename quirk to the acepc-t8 nvram file.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210928160633.96928-1-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c15b5fc054 ]
When CONFIG_PRINTK is not set, the CMPXCHG_BUGCHECK() macro calls
_printk(), but _printk() is a static inline function, not available
as an extern.
Since the purpose of the macro is to print the BUGCHECK info,
make this config option depend on PRINTK.
Fixes multiple occurrences of this build error:
../include/linux/printk.h:208:5: error: static declaration of '_printk' follows non-static declaration
208 | int _printk(const char *s, ...)
| ^~~~~~~
In file included from ../arch/ia64/include/asm/cmpxchg.h:5,
../arch/ia64/include/uapi/asm/cmpxchg.h:146:28: note: previous declaration of '_printk' with type 'int(const char *, ...)'
146 | extern int _printk(const char *fmt, ...);
Cc: linux-ia64@vger.kernel.org
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Chris Down <chris@chrisdown.name>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d0d779b21 ]
Some tools like v4l2-compliance let users select a media device based
on the bus_info string which can be quite convenient. Use a unique
string for that.
This also fixes the following v4l2-compliance warning:
warn: v4l2-test-media.cpp(52): empty bus_info
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdfaf4752e ]
If of_device_get_match_data() return NULL,
then null pointer dereference occurs in s5p_mfc_init_pm().
The patch adds checking if dev->variant is NULL.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8515965e5e ]
The variable pdev is assigned to dev->plat_dev, and dev->plat_dev is
checked in:
if (!dev->plat_dev)
This indicates both dev->plat_dev and pdev can be NULL. If so, the
function dev_err() is called to print error information.
dev_err(&pdev->dev, "No platform data specified\n");
However, &pdev->dev is an illegal address, and it is dereferenced in
dev_err().
To fix this possible null-pointer dereference, replace dev_err() with
mfc_err().
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Tuo Li <islituo@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3f60e7e1a ]
All the entities must have a unique name. We can have a descriptive and
unique name by appending the function and the entity->id.
This is even resilent to multi chain devices.
Fixes v4l2-compliance:
Media Controller ioctls:
fail: v4l2-test-media.cpp(205): v2_entity_names_set.find(key) != v2_entity_names_set.end()
test MEDIA_IOC_G_TOPOLOGY: FAIL
fail: v4l2-test-media.cpp(394): num_data_links != num_links
test MEDIA_IOC_ENUM_ENTITIES/LINKS: FAIL
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ffccdde5f0 ]
The device is doing something unexpected with the control. Either because
the protocol is not properly implemented or there has been a HW error.
Fixes v4l2-compliance:
Control ioctls (Input 0):
fail: v4l2-test-controls.cpp(448): s_ctrl returned an error (22)
test VIDIOC_G/S_CTRL: FAIL
fail: v4l2-test-controls.cpp(698): s_ext_ctrls returned an error (22)
test VIDIOC_G/S/TRY_EXT_CTRLS: FAIL
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 548fa43a58 ]
At the moment of enabling irq handling:
1922 ret = devm_request_threaded_irq(&pdev->dev, irq, dcmi_irq_callback,
1923 dcmi_irq_thread, IRQF_ONESHOT,
1924 dev_name(&pdev->dev), dcmi);
there is still uninitialized field sd_format of struct stm32_dcmi *dcmi.
If an interrupt occurs in the interval between the installation of the
interrupt handler and the initialization of this field, NULL pointer
dereference happens.
This field is dereferenced in the handler function without any check:
457 if (dcmi->sd_format->fourcc == V4L2_PIX_FMT_JPEG &&
458 dcmi->misr & IT_FRAME) {
The patch moves interrupt handler installation
after initialization of the sd_format field that happens in
dcmi_graph_notify_complete() via dcmi_set_default_fmt().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Dmitriy Ulitin <ulitin@ispras.ru>
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e16f5e39ac ]
There were several issues with handling errors in lm3554_probe():
- Probe did not set the error code when v4l2_ctrl_handler_init() failed.
- It intermixed gotos for handling errors of v4l2_ctrl_handler_init()
and media_entity_pads_init().
- It did not set the error code for failures of v4l2_ctrl_new_custom().
- Probe did not free resources in case of failures of
atomisp_register_i2c_module().
The patch fixes all these issues.
Found by Linux Driver Verification project (linuxtesting.org).
Link: https://lore.kernel.org/linux-media/20210810162943.19852-1-novikov@ispras.ru
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0961ba6dd2 ]
To prevent corrupted frames after starting and stopping the sensor its
datasheet specifies a specific pause sequence to follow:
Stopping:
Set Pause_Restart Bit -> Set Restart Bit -> Set Chip_Enable Off
Restarting:
Set Chip_Enable On -> Clear Pause_Restart Bit
The Restart Bit is cleared automatically and must not be cleared
manually as this would cause undefined behavior.
Signed-off-by: Dirk Bender <d.bender@phytec.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86a03dad0f ]
For fragmented packets, ath11k reassembles each fragment as a normal
packet and then reinjects it into HW ring. In this case, the DMA
direction should be DMA_TO_DEVICE, not DMA_FROM_DEVICE, otherwise
invalid payload will be reinjected to HW and then delivered to host.
What is more, since arbitrary memory could be allocated to the frame, we
don't know what kind of data is contained in the buffer reinjected.
Thus, as a bad result, private info may be leaked.
Note that this issue is only found on Intel platform.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916064617.20006-1-bqiang@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 441b3b5911 ]
When wlan interface is up, 11d scan is sent to the firmware, and the
firmware needs to spend couple of seconds to complete the 11d scan. If
immediately a normal scan from user space arrives to ath11k, then the
normal scan request is also sent to the firmware, but the scan started
event will be reported to ath11k until the 11d scan complete. When timed
out for the scan started in ath11k, ath11k stops the normal scan and the
firmware reports WMI_SCAN_EVENT_DEQUEUED to ath11k for the normal scan.
ath11k has no handler for the event and then timed out for the scan
completed in ath11k_scan_stop(), and ath11k prints the following error
message.
[ 1491.604750] ath11k_pci 0000:02:00.0: failed to receive scan abort comple: timed out
[ 1491.604756] ath11k_pci 0000:02:00.0: failed to stop scan: -110
[ 1491.604758] ath11k_pci 0000:02:00.0: failed to start hw scan: -110
Add a handler for WMI_SCAN_EVENT_DEQUEUED and then complete the scan to
get rid of the above error message.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914164226.38843-1-jouni@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69a0fcf8a9 ]
During firmware recovery, the default reg rules which are
received via WMI_REG_CHAN_LIST_CC_EVENT can overwrite
the currently configured user regd.
See below snap for example,
root@OpenWrt:/# iw reg get | grep country
country FR: DFS-ETSI
country FR: DFS-ETSI
country FR: DFS-ETSI
country FR: DFS-ETSI
root@OpenWrt:/# echo assert > /sys/kernel/debug/ath11k/ipq8074\ hw2.0/simulate_f
w_crash
<snip>
[ 5290.471696] ath11k c000000.wifi1: pdev 1 successfully recovered
root@OpenWrt:/# iw reg get | grep country
country FR: DFS-ETSI
country US: DFS-FCC
country US: DFS-FCC
country US: DFS-FCC
In the above, the user configured country 'FR' is overwritten
when the rules of default country 'US' are received and updated during
recovery. Hence avoid processing of these rules in general
during firmware recovery as they have been already applied during
driver registration or after last set user country is configured.
This scenario applies for both AP and STA devices basically because
cfg80211 is not aware of the recovery and only the driver recovers, but
changing or resetting of the reg domain during recovery is not needed so
as to continue with the configured regdomain currently in use.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01460-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-3-jouni@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f595d6a6c ]
fscrypt currently requires a 512-bit master key when AES-256-XTS is
used, since AES-256-XTS keys are 512-bit and fscrypt requires that the
master key be at least as long any key that will be derived from it.
However, this is overly strict because AES-256-XTS doesn't actually have
a 512-bit security strength, but rather 256-bit. The fact that XTS
takes twice the expected key size is a quirk of the XTS mode. It is
sufficient to use 256 bits of entropy for AES-256-XTS, provided that it
is first properly expanded into a 512-bit key, which HKDF-SHA512 does.
Therefore, relax the check of the master key size to use the security
strength of the derived key rather than the size of the derived key
(except for v1 encryption policies, which don't use HKDF).
Besides making things more flexible for userspace, this is needed in
order for the use of a KDF which only takes a 256-bit key to be
introduced into the fscrypt key hierarchy. This will happen with
hardware-wrapped keys support, as all known hardware which supports that
feature uses an SP800-108 KDF using AES-256-CMAC, so the wrapped keys
are wrapped 256-bit AES keys. Moreover, there is interest in fscrypt
supporting the same type of AES-256-CMAC based KDF in software as an
alternative to HKDF-SHA512. There is no security problem with such
features, so fix the key length check to work properly with them.
Reviewed-by: Paul Crowley <paulcrowley@google.com>
Link: https://lore.kernel.org/r/20210921030303.5598-1-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c606008b70 ]
When creating a new virtual interface in mwifiex_add_virtual_intf(), we
update our internal driver states like bss_type, bss_priority, bss_role
and bss_mode to reflect the mode the firmware will be set to.
When switching virtual interface mode using
mwifiex_init_new_priv_params() though, we currently only update bss_mode
and bss_role. In order for the interface mode switch to actually work,
we also need to update bss_type to its proper value, so do that.
This fixes a crash of the firmware (because the driver tries to execute
commands that are invalid in AP mode) when switching from station mode
to AP mode.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-9-verdre@v0yd.nl
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2e9666cdf ]
We currently handle changing from the P2P to the STATION virtual
interface type slightly different than changing from P2P to ADHOC: When
changing to STATION, we don't send the SET_BSS_MODE command. We do send
that command on all other type-changes though, and it probably makes
sense to send the command since after all we just changed our BSS_MODE.
Looking at prior changes to this part of the code, it seems that this is
simply a leftover from old refactorings.
Since sending the SET_BSS_MODE command is the only difference between
mwifiex_change_vif_to_sta_adhoc() and the current code, we can now use
mwifiex_change_vif_to_sta_adhoc() for both switching to ADHOC and
STATION interface type.
This does not fix any particular bug and just "looked right", so there's
a small chance it might be a regression.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-4-verdre@v0yd.nl
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit feab5bb8f1 ]
pdev_id in structure 'wmi_pdev_bss_chan_info_event' is wrongly placed
at the beginning. This causes invalid values in survey dump. Hence, align
the structure with the firmware.
Note: The firmware releases follow this order since the feature was
implemented. Also, it is not changing across the branches including
QCA6390.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Ritesh Singh <ritesi@codeaurora.org>
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210720214922.118078-3-jouni@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0db7c32ad3 ]
Early in debugging, it made some sense to differentiate the first
iteration from subsequent iterations, but now this just causes confusion.
This commit therefore moves the "set_tasks_gp_state(rtp, RTGS_WAIT_CBS)"
statement to the beginning of the "for" loop in rcu_tasks_kthread().
Reported-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e080f1775 ]
mq / mqprio make the default child qdiscs visible. They only do
so for the qdiscs which are within real_num_tx_queues when the
device is registered. Depending on order of calls in the driver,
or if user space changes config via ethtool -L the number of
qdiscs visible under tc qdisc show will differ from the number
of queues. This is confusing to users and potentially to system
configuration scripts which try to make sure qdiscs have the
right parameters.
Add a new Qdisc_ops callback and make relevant qdiscs TTRT.
Note that this uncovers the "shortcut" created by
commit 1f27cde313 ("net: sched: use pfifo_fast for non real queues")
The default child qdiscs beyond initial real_num_tx are always
pfifo_fast, no matter what the sysfs setting is. Fixing this
gets a little tricky because we'd need to keep a reference
on whatever the default qdisc was at the time of creation.
In practice this is likely an non-issue the qdiscs likely have
to be configured to non-default settings, so whatever user space
is doing such configuration can replace the pfifos... now that
it will see them.
Reported-by: Matthew Massey <matthewmassey@fb.com>
Reviewed-by: Dave Taht <dave.taht@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ca9ce2ba4 ]
Different SoCs have a different number of channels, e.g .:
* amazon-se has 10 channels,
* danube+ar9 have 20 channels,
* vr9 has 28 channels,
* ar10 has 24 channels.
We can read the ID register and, depending on the reported
number of channels, reset the appropriate number of channels.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c12aa581f6 ]
Reading the DMA registers immediately after the reset causes
Data Bus Error. Adding a small delay fixes this issue.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71921a9606 ]
rcutorture is generating some nesting scenarios that are not compatible on PREEMPT_RT.
For example:
preempt_disable();
rcu_read_lock_bh();
preempt_enable();
rcu_read_unlock_bh();
The problem here is that on PREEMPT_RT the bottom halves have to be
disabled and enabled in preemptible context.
Reorder locking: start with BH locking and continue with then with
disabling preemption or interrupts. In the unlocking do it reverse by
first enabling interrupts and preemption and BH at the very end.
Ensure that on PREEMPT_RT BH locking remains unchanged if in
non-preemptible context.
Link: https://lkml.kernel.org/r/20190911165729.11178-6-swood@redhat.com
Link: https://lkml.kernel.org/r/20210819182035.GF4126399@paulmck-ThinkPad-P17-Gen-1
Signed-off-by: Scott Wood <swood@redhat.com>
[bigeasy: Drop ATOM_BH, make it only about changing BH in atomic
context. Allow enabling RCU in IRQ-off section. Reword commit message.]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99c23da0ee ]
The sco_send_frame() also takes lock_sock() during memcpy_from_msg()
call that may be endlessly blocked by a task with userfaultd
technique, and this will result in a hung task watchdog trigger.
Just like the similar fix for hci_sock_sendmsg() in commit
92c685dc5de0 ("Bluetooth: reorganize functions..."), this patch moves
the memcpy_from_msg() out of lock_sock() for addressing the hang.
This should be the last piece for fixing CVE-2021-3640 after a few
already queued fixes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 820a2ab23d ]
2 improvements to the Lenovo Ideapad D330 panel-orientation quirks:
1. Some versions of the Lenovo Ideapad D330 have a DMI_PRODUCT_NAME of
"81H3" and others have "81MD". Testing has shown that the "81MD" also has
a 90 degree mounted panel. Drop the DMI_PRODUCT_NAME from the existing
quirk so that the existing quirk matches both variants.
2. Some of the Lenovo Ideapad D330 models have a HD (800x1280) screen
instead of a FHD (1200x1920) screen (both are mounted right-side-up) add
a second Lenovo Ideapad D330 quirk for the HD version.
Changes in v2:
- Add a new quirk for Lenovo Ideapad D330 models with a HD screen instead
of a FHD screen
Link: https://github.com/systemd/systemd/pull/18884
Acked-by: Simon Ser <contact@emersion.fr>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210530110428.12994-2-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f492283b15 ]
It is expected from the clients to follow the below steps on an imported
dmabuf fd:
a) dmabuf = dma_buf_get(fd) // Get the dmabuf from fd
b) dma_buf_attach(dmabuf); // Clients attach to the dmabuf
o Here the kernel does some slab allocations, say for
dma_buf_attachment and may be some other slab allocation in the
dmabuf->ops->attach().
c) Client may need to do dma_buf_map_attachment().
d) Accordingly dma_buf_unmap_attachment() should be called.
e) dma_buf_detach () // Clients detach to the dmabuf.
o Here the slab allocations made in b) are freed.
f) dma_buf_put(dmabuf) // Can free the dmabuf if it is the last
reference.
Now say an erroneous client failed at step c) above thus it directly
called dma_buf_put(), step f) above. Considering that it may be the last
reference to the dmabuf, buffer will be freed with pending attachments
left to the dmabuf which can show up as the 'memory leak'. This should
at least be reported as the WARN().
Signed-off-by: Charan Teja Reddy <charante@codeaurora.org>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1627043468-16381-1-git-send-email-charante@codeaurora.org
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0cf48167b8 upstream.
The gauge requires us to clear the status bits manually for some alerts
to be properly dismissed. Previously the IRQ was configured to react only
on falling edge, which wasn't technically correct (the ALRT line is active
low), but it had a happy side-effect of preventing interrupt storms
on uncleared alerts from happening.
Fixes: 7fbf6b731b ("power: supply: max17042: Do not enforce (incorrect) interrupt trigger type")
Cc: <stable@vger.kernel.org>
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9aaa81c336 upstream.
Chipidea core was calling the interrupt handler from non-IRQ context
with interrupts enabled, something which can lead to a deadlock if
there's an actual interrupt trying to take a lock that's already held
(e.g. the controller lock in udc_irq()).
Add a wrapper that can be used to fake interrupts instead of calling the
handler directly.
Fixes: 3ecb3e09b0 ("usb: chipidea: Use extcon framework for VBUS and ID detect")
Fixes: 876d4e1e82 ("usb: chipidea: core: add wakeup support for extcon")
Cc: Peter Chen <peter.chen@kernel.org>
Cc: stable@vger.kernel.org # 4.4
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211021083447.20078-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26df977a90 upstream.
The bindings file for this driver is defining the property as 'reg' but
the driver was reading it with the 'num' name. The bindings actually had
the 'num' property when added in
commit ea52c21268 ("dt-bindings: iio: dac: Add docs for AD5770R DAC")
and then changed it to 'reg' in
commit 2cf3818f18 ("dt-bindings: iio: dac: AD5570R fix bindings errors").
However, both these commits landed in v5.7 so the assumption is
that either 'num' is not being used or if it is, the validations were not
done.
Anyways, if someone comes back yelling about this, we might just support
both of the properties in the future. Not ideal, but that's life...
Fixes: 2cf3818f18 ("dt-bindings: iio: dac: AD5570R fix bindings errors")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210818080525.62790-1-nuno.sa@analog.com
Cc: Stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 558df982d4 upstream.
On success i2c_master_send() returns the number of bytes written. The
call from iio_write_channel_info(), however, expects the return value to
be zero on success.
This bug causes incorrect consumption of the sysfs buffer in
iio_write_channel_info(). When writing more than two characters to
out_voltage0_raw, the ad5446 write handler is called multiple times
causing unexpected behavior.
Fixes: 3ec36a2cf0 ("iio:ad5446: Add support for I2C based DACs")
Signed-off-by: Pekka Korpinen <pekka.korpinen@iki.fi>
Link: https://lore.kernel.org/r/20210929185755.2384-1-pekka.korpinen@iki.fi
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9bf3d20331 upstream.
The block number in the quota tree on disk should be smaller than the
v2_disk_dqinfo.dqi_blocks. If the quota file was corrupted, we may be
allocating an 'allocated' block and that would lead to a loop in a tree,
which will probably trigger oops later. This patch adds a check for the
block number in the quota tree to prevent such potential issue.
Link: https://lore.kernel.org/r/20211008093821.1001186-2-yi.zhang@huawei.com
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Cc: stable@kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84e1b4045d upstream.
Aardvark controller has something like config space of a Root Port
available at offset 0x0 of internal registers - these registers are used
for implementation of the emulated bridge.
The default value of Class Code of this bridge corresponds to a RAID Mass
storage controller, though. (This is probably intended for when the
controller is used as Endpoint.)
Change the Class Code to correspond to a PCI Bridge.
Add comment explaining this change.
Link: https://lore.kernel.org/r/20211028185659.20329-6-kabel@kernel.org
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 771153fc88 upstream.
From very vague, ambiguous and incomplete information from Marvell we
deduced that the 32-bit Aardvark register at address 0x4
(PCIE_CORE_CMD_STATUS_REG), which is not documented for Root Complex mode
in the Functional Specification (only for Endpoint mode), controls two
16-bit PCIe registers: Command Register and Status Registers of PCIe Root
Port.
This means that bit 2 controls bus mastering and forwarding of memory and
I/O requests in the upstream direction. According to PCI specifications
bits [0:2] of Command Register, this should be by default disabled on
reset. So explicitly disable these bits at early setup of the Aardvark
driver.
Remove code which unconditionally enables all 3 bits and let kernel code
(via pci_set_master() function) to handle bus mastering of Root PCIe
Bridge via emulated PCI_COMMAND on emulated bridge.
Link: https://lore.kernel.org/r/20211028185659.20329-5-kabel@kernel.org
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # b2a56469d5 ("PCI: aardvark: Add FIXME comment for PCIE_CORE_CMD_STATUS_REG access")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46ef6090db upstream.
Commit 366697018c ("PCI: aardvark: Add PHY support") introduced
configuration of PCIe Reference clock via PCIE_CORE_REF_CLK_REG register,
but did it incorrectly.
PCIe Reference clock differential pair is routed from system board to
endpoint card, so on CPU side it has output direction. Therefore it is
required to enable transmitting and disable receiving.
Default configuration according to Armada 3700 Functional Specifications is
enabled receiver part and disabled transmitter.
We need this change because otherwise PCIe Reference clock is configured to
some undefined state when differential pair is used for both transmitting
and receiving.
Fix this by disabling receiver part.
Link: https://lore.kernel.org/r/20211005180952.6812-6-kabel@kernel.org
Fixes: 366697018c ("PCI: aardvark: Add PHY support")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 661c399a65 upstream.
Current implementation of advk_pcie_link_up() is wrong as it marks also
link disabled or hot reset states as link up.
Fix it by marking link up only to those states which are defined in PCIe
Base specification 3.0, Table 4-14: Link Status Mapped to the LTSSM.
To simplify implementation, Define macros for every LTSSM state which
aardvark hardware can return in CFG_REG register.
Fix also checking for link training according to the same Table 4-14.
Define a new function advk_pcie_link_training() for this purpose.
Link: https://lore.kernel.org/r/20211005180952.6812-13-kabel@kernel.org
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Cc: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a7ca6d7fa3 upstream.
The PCIE_ISR1_REG says which interrupts are currently set / active,
including those which are masked.
The driver currently reads this register and looks if some unmasked
interrupts are active, and if not, it clears status bits of _all_
interrupts, including the masked ones.
This is incorrect, since, for example, some drivers may poll these bits.
Remove this clearing, and also remove this early return statement
completely, since it does not change functionality in any way.
Link: https://lore.kernel.org/r/20211005180952.6812-7-kabel@kernel.org
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a41ae80bd upstream.
The pci_bridge_emul_conf_write() function correctly clears W1C bits in
cfgspace cache, but it does not inform the underlying implementation
about the clear request: the .write_op() method is given the value with
these bits cleared.
This is wrong if the .write_op() needs to know which bits were requested
to be cleared.
Fix the value to be passed into the .write_op() method to have requested
W1C bits set, so that it can clear them.
Both pci-bridge-emul users (mvebu and aardvark) are compatible with this
change.
Link: https://lore.kernel.org/r/20211028185659.20329-2-kabel@kernel.org
Fixes: 23a5fba4d9 ("PCI: Introduce PCI bridge emulated config space common logic")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a25440376 upstream.
Example for triggering use after free in a overlay on ext4 setup:
aio_read
ovl_read_iter
vfs_iter_read
ext4_file_read_iter
ext4_dio_read_iter
iomap_dio_rw -> -EIOCBQUEUED
/*
* Here IO is completed in a separate thread,
* ovl_aio_cleanup_handler() frees aio_req which has iocb embedded
*/
file_accessed(iocb->ki_filp); /**BOOM**/
Fix by introducing a refcount in ovl_aio_req similarly to aio_kiocb. This
guarantees that iocb is only freed after vfs_read/write_iter() returns on
underlying fs.
Fixes: 2406a307ac ("ovl: implement async IO routines")
Signed-off-by: yangerkun <yangerkun@huawei.com>
Link: https://lore.kernel.org/r/20210930032228.3199690-3-yangerkun@huawei.com/
Cc: <stable@vger.kernel.org> # v5.6
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40fdea0284 upstream.
When running as PVH or HVM guest with actual memory < max memory the
hypervisor is using "populate on demand" in order to allow the guest
to balloon down from its maximum memory size. For this to work
correctly the guest must not touch more memory pages than its target
memory size as otherwise the PoD cache will be exhausted and the guest
is crashed as a result of that.
In extreme cases ballooning down might not be finished today before
the init process is started, which can consume lots of memory.
In order to avoid random boot crashes in such cases, add a late init
call to wait for ballooning down having finished for PVH/HVM guests.
Warn on console if initial ballooning fails, panic() after stalling
for more than 3 minutes per default. Add a module parameter for
changing this timeout.
[boris: replaced pr_info() with pr_notice()]
Cc: <stable@vger.kernel.org>
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20211102091944.17487-1-jgross@suse.com
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7444d706be upstream.
The driver no longer depends on this option, but it fails to
build if it's disabled because the skb->tc_skip_classify is
hidden behind an #ifdef:
drivers/net/ifb.c:81:8: error: no member named 'tc_skip_classify' in 'struct sk_buff'
skb->tc_skip_classify = 1;
Use the same #ifdef around the assignment.
Fixes: 046178e726 ("ifb: Depend on netfilter alternatively to tc")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 027b57170b upstream.
Since commit edc6afc549 ("tty: switch to ktermios and new framework")
termios speed is no longer stored only in c_cflag member but also in new
additional c_ispeed and c_ospeed members. If BOTHER flag is set in c_cflag
then termios speed is stored only in these new members.
Therefore to correctly restore termios speed it is required to store also
ispeed and ospeed members, not only cflag member.
In case only cflag member with BOTHER flag is restored then functions
tty_termios_baud_rate() and tty_termios_input_baud_rate() returns baudrate
stored in c_ospeed / c_ispeed member, which is zero as it was not restored
too. If reported baudrate is invalid (e.g. zero) then serial core functions
report fallback baudrate value 9600. So it means that in this case original
baudrate is lost and kernel changes it to value 9600.
Simple reproducer of this issue is to boot kernel with following command
line argument: "console=ttyXXX,86400" (where ttyXXX is the device name).
For speed 86400 there is no Bnnn constant and therefore kernel has to
represent this speed via BOTHER c_cflag. Which means that speed is stored
only in c_ospeed and c_ispeed members, not in c_cflag anymore.
If bootloader correctly configures serial device to speed 86400 then kernel
prints boot log to early console at speed speed 86400 without any issue.
But after kernel starts initializing real console device ttyXXX then speed
is changed to fallback value 9600 because information about speed was lost.
This patch fixes above issue by storing and restoring also ispeed and
ospeed members, which are required for BOTHER flag.
Fixes: edc6afc549 ("[PATCH] tty: switch to ktermios and new framework")
Cc: stable@vger.kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20211002130900.9518-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51d1579466 upstream.
The resetting of the entire ring buffer use to simply go through and reset
each individual CPU buffer that had its own protection and synchronization.
But this was very slow, due to performing a synchronization for each CPU.
The code was reshuffled to do one disabling of all CPU buffers, followed
by a single RCU synchronization, and then the resetting of each of the CPU
buffers. But unfortunately, the mutex that prevented multiple occurrences
of resetting the buffer was not moved to the upper function, and there is
nothing to protect from it.
Take the ring buffer mutex around the global reset.
Cc: stable@vger.kernel.org
Fixes: b23d7a5f4a ("ring-buffer: speed up buffer resets by avoiding synchronize_rcu for each CPU")
Reported-by: "Tzvetomir Stoyanov (VMware)" <tz.stoyanov@gmail.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7dfbc624eb upstream.
Check the current VMCS controls to determine if an MSR write will be
intercepted due to MSR bitmaps being disabled. In the nested VMX case,
KVM will disable MSR bitmaps in vmcs02 if they're disabled in vmcs12 or
if KVM can't map L1's bitmaps for whatever reason.
Note, the bad behavior is relatively benign in the current code base as
KVM sets all bits in vmcs02's MSR bitmap by default, clears bits if and
only if L0 KVM also disables interception of an MSR, and only uses the
buggy helper for MSR_IA32_SPEC_CTRL. Because KVM explicitly tests WRMSR
before disabling interception of MSR_IA32_SPEC_CTRL, the flawed check
will only result in KVM reading MSR_IA32_SPEC_CTRL from hardware when it
isn't strictly necessary.
Tag the fix for stable in case a future fix wants to use
msr_write_intercepted(), in which case a buggy implementation in older
kernels could prove subtly problematic.
Fixes: d28b387fb7 ("KVM/VMX: Allow direct access to MSR_IA32_SPEC_CTRL")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211109013047.2041518-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8bb084119f upstream.
Since ARMv8.0 the upper 32 bits of ESR_ELx have been RES0, and recently
some of the upper bits gained a meaning and can be non-zero. For
example, when FEAT_LS64 is implemented, ESR_ELx[36:32] contain ISS2,
which for an ST64BV or ST64BV0 can be non-zero. This can be seen in ARM
DDI 0487G.b, page D13-3145, section D13.2.37.
Generally, we must not rely on RES0 bit remaining zero in future, and
when extracting ESR_ELx.EC we must mask out all other bits.
All C code uses the ESR_ELx_EC() macro, which masks out the irrelevant
bits, and therefore no alterations are required to C code to avoid
consuming irrelevant bits.
In a couple of places the KVM assembly extracts ESR_ELx.EC using LSR on
an X register, and so could in theory consume previously RES0 bits. In
both cases this is for comparison with EC values ESR_ELx_EC_HVC32 and
ESR_ELx_EC_HVC64, for which the upper bits of ESR_ELx must currently be
zero, but this could change in future.
This patch adjusts the KVM vectors to use UBFX rather than LSR to
extract ESR_ELx.EC, ensuring these are robust to future additions to
ESR_ELx.
Cc: stable@vger.kernel.org
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Alexandru Elisei <alexandru.elisei@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211103110545.4613-1-mark.rutland@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 223a3b8283 upstream.
On Galaxy S3 (i9300/i9305), which has the max17047 fuel gauge and no
current sense resistor (rsns), the RepSOC register does not provide an
accurate state of charge value. The reported value is wrong, and does
not change over time. VFSOC however, which uses the voltage fuel gauge
to determine the state of charge, always shows an accurate value.
For devices without current sense, VFSOC is already used for the
soc-alert (0x0003 is written to MiscCFG register), so with this change
the source of the alert and the PROP_CAPACITY value match.
Fixes: 359ab9f5b1 ("power_supply: Add MAX17042 Fuel Gauge Driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Suggested-by: Wolfgang Wiedmeyer <wolfgit@wiedmeyer.de>
Signed-off-by: Henrik Grimler <henrik@grimler.se>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4ebddd654 upstream.
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: b36bf0a0fe ("mtd: rawnand: socrates: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-9-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc7e5940aa upstream.
In orininal code, use 2 function spin_lock() and local_irq_save() to
protect the critical zone. But when enable the kernel debug config,
there are below inconsistent lock state detected.
================================
WARNING: inconsistent lock state
5.10.63-yocto-standard #1 Not tainted
--------------------------------
inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
lock_torture_wr/226 [HC0[0]:SC1[5]:HE1:SE0] takes:
ffff002005b2dd80 (&p->access_spinlock){+.?.}-{3:3}, at: qbman_swp_enqueue_multiple_mem_back+0x44/0x270
{SOFTIRQ-ON-W} state was registered at:
lock_acquire.part.0+0xf8/0x250
lock_acquire+0x68/0x84
_raw_spin_lock+0x68/0x90
qbman_swp_enqueue_multiple_mem_back+0x44/0x270
......
cryptomgr_test+0x38/0x60
kthread+0x158/0x164
ret_from_fork+0x10/0x38
irq event stamp: 4498
hardirqs last enabled at (4498): [<ffff800010fcf980>] _raw_spin_unlock_irqrestore+0x90/0xb0
hardirqs last disabled at (4497): [<ffff800010fcffc4>] _raw_spin_lock_irqsave+0xd4/0xe0
softirqs last enabled at (4458): [<ffff8000100108c4>] __do_softirq+0x674/0x724
softirqs last disabled at (4465): [<ffff80001005b2a4>] __irq_exit_rcu+0x190/0x19c
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&p->access_spinlock);
<Interrupt>
lock(&p->access_spinlock);
*** DEADLOCK ***
So, in order to avoid deadlock, use the combined functions
spin_lock_irqsave/spin_unlock_irqrestore() to protect critical zone.
Fixes: 3b2abda7d2 ("soc: fsl: dpio: Replace QMAN array mode with ring mode enqueue")
Cc: stable@vger.kernel.org
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e775eb9fc2 upstream.
When enable debug kernel configs,there will be calltrace as below:
BUG: using smp_processor_id() in preemptible [00000000] code: swapper/0/1
caller is debug_smp_processor_id+0x20/0x30
CPU: 6 PID: 1 Comm: swapper/0 Not tainted 5.10.63-yocto-standard #1
Hardware name: NXP Layerscape LX2160ARDB (DT)
Call trace:
dump_backtrace+0x0/0x1a0
show_stack+0x24/0x30
dump_stack+0xf0/0x13c
check_preemption_disabled+0x100/0x110
debug_smp_processor_id+0x20/0x30
dpaa2_io_query_fq_count+0xdc/0x154
dpaa2_eth_stop+0x144/0x314
__dev_close_many+0xdc/0x160
__dev_change_flags+0xe8/0x220
dev_change_flags+0x30/0x70
ic_close_devs+0x50/0x78
ip_auto_config+0xed0/0xf10
do_one_initcall+0xac/0x460
kernel_init_freeable+0x30c/0x378
kernel_init+0x20/0x128
ret_from_fork+0x10/0x38
Based on comment in the context, it doesn't matter whether
preemption is disable or not. So, replace smp_processor_id()
with raw_smp_processor_id() to avoid above call trace.
Fixes: c89105c9b3 ("staging: fsl-mc: Move DPIO from staging to drivers/soc/fsl")
Cc: stable@vger.kernel.org
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95bf9d646c upstream.
When an instruction to save or restore a register from the stack fails
in _save_fp_context or _restore_fp_context return with -EFAULT. This
change was made to r2300_fpu.S[1] but it looks like it got lost with
the introduction of EX2[2]. This is also what the other implementation
of _save_fp_context and _restore_fp_context in r4k_fpu.S does, and
what is needed for the callers to be able to handle the error.
Furthermore calling do_exit(SIGSEGV) from bad_stack is wrong because
it does not terminate the entire process it just terminates a single
thread.
As the changed code was the only caller of arch/mips/kernel/syscall.c:bad_stack
remove the problematic and now unused helper function.
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Maciej Rozycki <macro@orcam.me.uk>
Cc: linux-mips@vger.kernel.org
[1] 35938a00ba ("MIPS: Fix ISA I FP sigcontext access violation handling")
[2] f92722dc45 ("MIPS: Correct MIPS I FP sigcontext layout")
Cc: stable@vger.kernel.org
Fixes: f92722dc45 ("MIPS: Correct MIPS I FP sigcontext layout")
Acked-by: Maciej W. Rozycki <macro@orcam.me.uk>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Link: https://lkml.kernel.org/r/20211020174406.17889-5-ebiederm@xmission.com
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fff53a551d upstream.
This patch fixes 2 problems:
[1] The output warning logs and data loss when performing
mount/umount then remount the device with jffs2 format.
[2] The access width of SMWDR[0:1]/SMRDR[0:1] register is wrong.
This is the sample warning logs when performing mount/umount then
remount the device with jffs2 format:
jffs2: jffs2_scan_inode_node(): CRC failed on node at 0x031c51d4:
Read 0x00034e00, calculated 0xadb272a7
The reason for issue [1] is that the writing data seems to
get messed up.
Data is only completed when the number of bytes is divisible by 4.
If you only have 3 bytes of data left to write, 1 garbage byte
is inserted after the end of the write stream.
If you only have 2 bytes of data left to write, 2 bytes of '00'
are added into the write stream.
If you only have 1 byte of data left to write, 2 bytes of '00'
are added into the write stream. 1 garbage byte is inserted after
the end of the write stream.
To solve problem [1], data must be written continuously in serial
and the write stream ends when data is out.
Following HW manual 62.2.15, access to SMWDR0 register should be
in the same size as the transfer size specified in the SPIDE[3:0]
bits in the manual mode enable setting register (SMENR).
Be sure to access from address 0.
So, in 16-bit transfer (SPIDE[3:0]=b'1100), SMWDR0 should be
accessed by 16-bit width.
Similar to SMWDR1, SMDDR0/1 registers.
In current code, SMWDR0 register is accessed by regmap_write()
that only set up to do 32-bit width.
To solve problem [2], data must be written 16-bit or 8-bit when
transferring 1-byte or 2-byte.
Fixes: ca7d8b980b ("memory: add Renesas RPC-IF driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Duc Nguyen <duc.nguyen.ub@renesas.com>
[wsa: refactored to use regmap only via reg_read/reg_write]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210922091007.5516-1-wsa+renesas@sang-engineering.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d613f9f72 upstream.
The existence of sigkill_pending is a little silly as it is
functionally a duplicate of fatal_signal_pending that is used in
exactly one place.
Checking for pending fatal signals and returning early in ptrace_stop
is actively harmful. It casues the ptrace_stop called by
ptrace_signal to return early before setting current->exit_code.
Later when ptrace_signal reads the signal number from
current->exit_code is undefined, making it unpredictable what will
happen.
Instead rely on the fact that schedule will not sleep if there is a
pending signal that can awaken a task.
Removing the explict sigkill_pending test fixes fixes ptrace_signal
when ptrace_stop does not stop because current->exit_code is always
set to to signr.
Cc: stable@vger.kernel.org
Fixes: 3d749b9e67 ("ptrace: simplify ptrace_stop()->sigkill_pending() path")
Fixes: 1a669c2f16 ("Add arch_ptrace_stop")
Link: https://lkml.kernel.org/r/87pmsyx29t.fsf@disp2133
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b515d09705 upstream.
P2P client mode was only working the first time.
On subsequent connection attempts the group was successfully created but
no data was sent (no transmitted data packets were seen with a sniffer).
The reason for this was that the hardware was being configured in fixed
rate mode with rate RSI_RATE_1 (1Mbps) which is not valid in the 5GHz band.
In P2P mode wpa_supplicant uses NL80211_CMD_SET_TX_BITRATE_MASK to disallow
the 11b rates in the 2.4GHz band which updated common->fixedrate_mask.
rsi_set_min_rate() then used the fixedrate_mask to calculate the minimum
allowed rate, or 0xffff = auto if none was found.
However that calculation did not account for the different rate sets
allowed in the different bands leading to the error.
Fixing set_min_rate() would result in 6Mb/s being used all the time
which is not what we want either.
The reason the problem did not occur on the first connection is that
rsi_mac80211_set_rate_mask() only updated the fixedrate_mask for
the *current* band. When it was called that was still 2.4GHz as the
switch is done later. So the when set_min_rate() was subsequently
called after the switch to 5GHz it still had a mask of zero, leading
to defaulting to auto mode.
Fix this by differentiating the case of a single rate being
requested, in which case the hardware will be used in fixed rate
mode with just that rate, and multiple rates being requested,
in which case we remain in auto mode but the firmware rate selection
algorithm is configured with a restricted set of rates.
Fixes: dad0d04fa7 ("rsi: Add RS9113 wireless driver")
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
CC: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630337206-12410-4-git-send-email-martin.fuzzey@flowbird.group
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 99ac601882 upstream.
My previous patch checked if encryption should be enabled by directly
checking info->control.hw_key (like the downstream driver).
However that missed that the control and driver_info members of
struct ieee80211_tx_info are union fields.
Due to this when rsi_core_xmit() updates fields in "tx_params"
(driver_info) it can overwrite the control.hw_key, causing the result
of the later test to be incorrect.
With the current structure layout the first byte of control.hw_key is
overlayed with the vap_id so, since we only test if control.hw_key is
NULL / non NULL, a non zero vap_id will incorrectly enable encryption.
In basic STA and AP modes the vap_id is always zero so it works but in
P2P client mode a second VIF is created causing vap_id to be non zero
and hence encryption to be enabled before keys have been set.
Fix this by extracting the key presence flag to a new field in the driver
private tx_params structure and populating it first.
Fixes: 314538041b ("rsi: fix AP mode with WPA failure due to encrypted EAPOL")
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
CC: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630337206-12410-3-git-send-email-martin.fuzzey@flowbird.group
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b14ed6e11 upstream.
When BT coexistence is enabled (eg oper mode 13, which is the default)
the initialisation on startup sometimes silently fails.
In a normal initialisation we see
usb 1-1.3: Product: Wireless USB Network Module
usb 1-1.3: Manufacturer: Redpine Signals, Inc.
usb 1-1.3: SerialNumber: 000000000001
rsi_91x: rsi_probe: Initialized os intf ops
rsi_91x: rsi_load_9116_firmware: Loading chunk 0
rsi_91x: rsi_load_9116_firmware: Loading chunk 1
rsi_91x: rsi_load_9116_firmware: Loading chunk 2
rsi_91x: Max Stations Allowed = 1
But sometimes the last log is missing and the wlan net device is
not created.
Running a userspace loop that resets the hardware via a GPIO shows the
problem occurring ~5/100 resets.
The problem does not occur in oper mode 1 (wifi only).
Adding logs shows that the initialisation state machine requests a MAC
reset via rsi_send_reset_mac() but the firmware does not reply, leading
to the initialisation sequence being incomplete.
Fix this by delaying attaching the BT adapter until the wifi
initialisation has completed.
With this applied I have done > 300 reset loops with no errors.
Fixes: 716b840c76 ("rsi: handle BT traffic in driver")
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
CC: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630337206-12410-2-git-send-email-martin.fuzzey@flowbird.group
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f971a85439 upstream.
Checking if DMA is enabled should be done via the
ata_dma_enabled helper function, since the init state
0xff indicates disabled.
This meant that ATA_CMD_READ_LOG_DMA_EXT was used and probed
for before DMA was enabled, which caused hangs for some combinations
of controllers and devices.
It might also have caused it to be incorrectly disabled as broken,
but there have been no reports of that.
Cc: stable@vger.kernel.org
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=195895
Signed-off-by: Reimar Döffinger <Reimar.Doeffinger@gmx.de>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e3e59c31f upstream.
It seems that the PCIe+USB firmware (latest version 15.68.19.p21) of the
88W8897 card sometimes ignores or misses when we try to wake it up by
writing to the firmware status register. This leads to the firmware
wakeup timeout expiring and the driver resetting the card because we
assume the firmware has hung up or crashed.
Turns out that the firmware actually didn't hang up, but simply "missed"
our wakeup request and didn't send us an interrupt with an AWAKE event.
Trying again to read the firmware status register after a short timeout
usually makes the firmware wake up as expected, so add a small retry
loop to mwifiex_pm_wakeup_card() that looks at the interrupt status to
check whether the card woke up.
The number of tries and timeout lengths for this were determined
experimentally: The firmware usually takes about 500 us to wake up
after we attempt to read the status register. In some cases where the
firmware is very busy (for example while doing a bluetooth scan) it
might even miss our requests for multiple milliseconds, which is why
after 15 tries the waiting time gets increased to 10 ms. The maximum
number of tries it took to wake the firmware when testing this was
around 20, so a maximum number of 50 tries should give us plenty of
safety margin.
Here's a reproducer for those firmware wakeup failures I've found:
1) Make sure wifi powersaving is enabled (iw dev wlp1s0 set power_save on)
2) Connect to any wifi network (makes firmware go into wifi powersaving
mode, not deep sleep)
3) Make sure bluetooth is turned off (to ensure the firmware actually
enters powersave mode and doesn't keep the radio active doing bluetooth
stuff)
4) To confirm that wifi powersaving is entered ping a device on the LAN,
pings should be a few ms higher than without powersaving
5) Run "while true; do iwconfig; sleep 0.0001; done", this wakes and
suspends the firmware extremely often
6) Wait until things explode, for me it consistently takes <5 minutes
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=109681
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011133224.15561-3-verdre@v0yd.nl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5f4eb8223 upstream.
On the 88W8897 PCIe+USB card the firmware randomly crashes after setting
the TX ring write pointer. The issue is present in the latest firmware
version 15.68.19.p21 of the PCIe+USB card.
Those firmware crashes can be worked around by reading any PCI register
of the card after setting that register, so read the PCI_VENDOR_ID
register here. The reason this works is probably because we keep the bus
from entering an ASPM state for a bit longer, because that's what causes
the cards firmware to crash.
This fixes a bug where during RX/TX traffic and with ASPM L1 substates
enabled (the specific substates where the issue happens appear to be
platform dependent), the firmware crashes and eventually a command
timeout appears in the logs.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=109681
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011133224.15561-2-verdre@v0yd.nl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 928265e360 upstream.
There is no reason to allow "syscore" devices to runtime-suspend
during system-wide PM transitions, because they are subject to the
same possible failure modes as any other devices in that respect.
Accordingly, change device_prepare() and device_complete() to call
pm_runtime_get_noresume() and pm_runtime_put(), respectively, for
"syscore" devices too.
Fixes: 057d51a126 ("Merge branch 'pm-sleep'")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: 3.10+ <stable@vger.kernel.org> # 3.10+
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3fd2c95c1 upstream.
We observe unexpected connection drops with some APs due to
non-acked mac80211 generated null data frames (keep-alive).
After debugging and capture, we noticed that null frames are
submitted at standard data bitrate and that the given APs are
in trouble with that.
After setting the null frame bitrate to control bitrate, all
null frames are acked as expected and connection is maintained.
Not sure if it's a requirement of the specification, but it seems
the right thing to do anyway, null frames are mostly used for control
purpose (power-saving, keep-alive...), and submitting them with
a slower/simpler bitrate/modulation is more robust.
Cc: stable@vger.kernel.org
Fixes: 512b191d96 ("wcn36xx: Fix TX data path")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634560399-15290-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a9e79b116c upstream.
This change fix the TX ack mechanism in various ways:
- For NO_ACK tagged packets, we don't need to wait for TX_ACK indication
and so are not subject to the single packet ack limitation. So we don't
have to stop the tx queue, and can call the tx status callback as soon
as DMA transfer has completed.
- Fix skb ownership/reference. Only start status indication timeout
once the DMA transfer has been completed. This avoids the skb to be
both referenced in the DMA tx ring and by the tx_ack_skb pointer,
preventing any use-after-free or double-free.
- This adds a sanity (paranoia?) check on the skb tx ack pointer.
- Resume TX queue if TX status tagged packet TX fails.
Cc: stable@vger.kernel.org
Fixes: fdf21cc371 ("wcn36xx: Add TX ack support")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634567281-28997-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 046178e726 upstream.
IFB originally depended on NET_CLS_ACT for traffic redirection.
But since v4.5, that may be achieved with NFT_FWD_NETDEV as well.
Fixes: 39e6dea28a ("netfilter: nf_tables: add forward expression to the netdev family")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v4.5+: bcfabee1af: netfilter: nft_fwd_netdev: allow to redirect to ifb via ingress
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a006acb931 upstream.
Add the missing endpoint max-packet sanity check to probe() to avoid
division by zero in ath10k_usb_hif_tx_sg() in case a malicious device
has broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4f ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: 4db66499df ("ath10k: add initial USB support")
Cc: stable@vger.kernel.org # 4.14
Cc: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027080819.6675-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1b9ca365d upstream.
Add the missing endpoint max-packet sanity check to probe() to avoid
division by zero in ath10k_usb_hif_tx_sg() in case a malicious device
has broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4f ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: 9cbee35868 ("ath6kl: add full USB support")
Cc: stable@vger.kernel.org # 3.5
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027080819.6675-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89f8765a11 upstream.
Add the missing endpoint sanity checks to probe() to avoid division by
zero in mwifiex_write_data_sync() in case a malicious device has broken
descriptors (or when doing descriptor fuzz testing).
Only add checks for the firmware-download boot stage, which require both
command endpoints, for now. The driver looks like it will handle a
missing endpoint during normal operation without oopsing, albeit not
very gracefully as it will try to submit URBs to the default pipe and
fail.
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4f ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: 4daffe3543 ("mwifiex: add support for Marvell USB8797 chipset")
Cc: stable@vger.kernel.org # 3.5
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027080819.6675-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b16bef60a9 upstream.
The driver and its bindings, before commit 04f9f068a6 ("regulator:
s5m8767: Modify parsing method of the voltage table of buck2/3/4") were
requiring to provide at least one safe/default voltage for DVS registers
if DVS GPIO is not being enabled.
IOW, if s5m8767,pmic-buck2-uses-gpio-dvs is missing, the
s5m8767,pmic-buck2-dvs-voltage should still be present and contain one
voltage.
This requirement was coming from driver behavior matching this condition
(none of DVS GPIO is enabled): it was always initializing the DVS
selector pins to 0 and keeping the DVS enable setting at reset value
(enabled). Therefore if none of DVS GPIO is enabled in devicetree,
driver was configuring the first DVS voltage for buck[234].
Mentioned commit 04f9f068a6 ("regulator: s5m8767: Modify parsing
method of the voltage table of buck2/3/4") broke it because DVS voltage
won't be parsed from devicetree if DVS GPIO is not enabled. After the
change, driver will configure bucks to use the register reset value as
voltage which might have unpleasant effects.
Fix this by relaxing the bindings constrain: if DVS GPIO is not enabled
in devicetree (therefore DVS voltage is also not parsed), explicitly
disable it.
Cc: <stable@vger.kernel.org>
Fixes: 04f9f068a6 ("regulator: s5m8767: Modify parsing method of the voltage table of buck2/3/4")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Rob Herring <robh@kernel.org>
Message-Id: <20211008113723.134648-2-krzysztof.kozlowski@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cbfcd13be5 upstream.
Current code contains a lot of racy patterns when converting an
ocontext's context structure to an SID. This is being done in a "lazy"
fashion, such that the SID is looked up in the SID table only when it's
first needed and then cached in the "sid" field of the ocontext
structure. However, this is done without any locking or memory barriers
and is thus unsafe.
Between commits 24ed7fdae6 ("selinux: use separate table for initial
SID lookup") and 66f8e2f03c ("selinux: sidtab reverse lookup hash
table"), this race condition lead to an actual observable bug, because a
pointer to the shared sid field was passed directly to
sidtab_context_to_sid(), which was using this location to also store an
intermediate value, which could have been read by other threads and
interpreted as an SID. In practice this caused e.g. new mounts to get a
wrong (seemingly random) filesystem context, leading to strange denials.
This bug has been spotted in the wild at least twice, see [1] and [2].
Fix the race condition by making all the racy functions use a common
helper that ensures the ocontext::sid accesses are made safely using the
appropriate SMP constructs.
Note that security_netif_sid() was populating the sid field of both
contexts stored in the ocontext, but only the first one was actually
used. The SELinux wiki's documentation on the "netifcon" policy
statement [3] suggests that using only the first context is intentional.
I kept only the handling of the first context here, as there is really
no point in doing the SID lookup for the unused one.
I wasn't able to reproduce the bug mentioned above on any kernel that
includes commit 66f8e2f03c, even though it has been reported that the
issue occurs with that commit, too, just less frequently. Thus, I wasn't
able to verify that this patch fixes the issue, but it makes sense to
avoid the race condition regardless.
[1] https://github.com/containers/container-selinux/issues/89
[2] https://lists.fedoraproject.org/archives/list/selinux@lists.fedoraproject.org/thread/6DMTAMHIOAOEMUAVTULJD45JZU7IBAFM/
[3] https://selinuxproject.org/page/NetworkStatements#netifcon
Cc: stable@vger.kernel.org
Cc: Xinjie Zheng <xinjie@google.com>
Reported-by: Sujithra Periasamy <sujithra@google.com>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c78a5e7aa upstream.
In open_ctree() in btrfs_check_rw_degradable() [1], we check each block
group individually if at least the minimum number of devices is available
for that profile. If all the devices are available, then we don't have to
check degradable.
[1]
open_ctree()
::
3559 if (!sb_rdonly(sb) && !btrfs_check_rw_degradable(fs_info, NULL)) {
Also before calling btrfs_check_rw_degradable() in open_ctee() at the
line number shown below [2] we call btrfs_read_chunk_tree() and down to
add_missing_dev() to record number of missing devices.
[2]
open_ctree()
::
3454 ret = btrfs_read_chunk_tree(fs_info);
btrfs_read_chunk_tree()
read_one_chunk() / read_one_dev()
add_missing_dev()
So, check if there is any missing device before btrfs_check_rw_degradable()
in open_ctree().
Also, with this the mount command could save ~16ms.[3] in the most
common case, that is no device is missing.
[3]
1) * 16934.96 us | btrfs_check_rw_degradable [btrfs]();
CC: stable@vger.kernel.org # 4.19+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10adb1152d upstream.
At replay_dir_deletes(), if find_dir_range() returns an error we break out
of the main while loop and then assign a value of 0 (success) to the 'ret'
variable, resulting in completely ignoring that an error happened. Fix
that by jumping to the 'out' label when find_dir_range() returns an error
(negative value).
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d03dbebba upstream.
Reported bug: https://github.com/kdave/btrfs-progs/issues/389
There's a problem with scrub reporting aborted status but returning
error code 0, on a filesystem with missing and readded device.
Roughly these steps:
- mkfs -d raid1 dev1 dev2
- fill with data
- unmount
- make dev1 disappear
- mount -o degraded
- copy more data
- make dev1 appear again
Running scrub afterwards reports that the command was aborted, but the
system log message says the exit code was 0.
It seems that the cause of the error is decrementing
fs_devices->missing_devices but not clearing device->dev_state. Every
time we umount filesystem, it would call close_ctree, And it would
eventually involve btrfs_close_one_device to close the device, but it
only decrements fs_devices->missing_devices but does not clear the
device BTRFS_DEV_STATE_MISSING bit. Worse, this bug will cause Integer
Overflow, because every time umount, fs_devices->missing_devices will
decrease. If fs_devices->missing_devices value hit 0, it would overflow.
With added debugging:
loop1: detected capacity change from 0 to 20971520
BTRFS: device fsid 56ad51f1-5523-463b-8547-c19486c51ebb devid 1 transid 21 /dev/loop1 scanned by systemd-udevd (2311)
loop2: detected capacity change from 0 to 20971520
BTRFS: device fsid 56ad51f1-5523-463b-8547-c19486c51ebb devid 2 transid 17 /dev/loop2 scanned by systemd-udevd (2313)
BTRFS info (device loop1): flagging fs with big metadata feature
BTRFS info (device loop1): allowing degraded mounts
BTRFS info (device loop1): using free space tree
BTRFS info (device loop1): has skinny extents
BTRFS info (device loop1): before clear_missing.00000000f706684d /dev/loop1 0
BTRFS warning (device loop1): devid 2 uuid 6635ac31-56dd-4852-873b-c60f5e2d53d2 is missing
BTRFS info (device loop1): before clear_missing.0000000000000000 /dev/loop2 1
BTRFS info (device loop1): flagging fs with big metadata feature
BTRFS info (device loop1): allowing degraded mounts
BTRFS info (device loop1): using free space tree
BTRFS info (device loop1): has skinny extents
BTRFS info (device loop1): before clear_missing.00000000f706684d /dev/loop1 0
BTRFS warning (device loop1): devid 2 uuid 6635ac31-56dd-4852-873b-c60f5e2d53d2 is missing
BTRFS info (device loop1): before clear_missing.0000000000000000 /dev/loop2 0
BTRFS info (device loop1): flagging fs with big metadata feature
BTRFS info (device loop1): allowing degraded mounts
BTRFS info (device loop1): using free space tree
BTRFS info (device loop1): has skinny extents
BTRFS info (device loop1): before clear_missing.00000000f706684d /dev/loop1 18446744073709551615
BTRFS warning (device loop1): devid 2 uuid 6635ac31-56dd-4852-873b-c60f5e2d53d2 is missing
BTRFS info (device loop1): before clear_missing.0000000000000000 /dev/loop2 18446744073709551615
If fs_devices->missing_devices is 0, next time it would be 18446744073709551615
After apply this patch, the fs_devices->missing_devices seems to be
right:
$ truncate -s 10g test1
$ truncate -s 10g test2
$ losetup /dev/loop1 test1
$ losetup /dev/loop2 test2
$ mkfs.btrfs -draid1 -mraid1 /dev/loop1 /dev/loop2 -f
$ losetup -d /dev/loop2
$ mount -o degraded /dev/loop1 /mnt/1
$ umount /mnt/1
$ mount -o degraded /dev/loop1 /mnt/1
$ umount /mnt/1
$ mount -o degraded /dev/loop1 /mnt/1
$ umount /mnt/1
$ dmesg
loop1: detected capacity change from 0 to 20971520
loop2: detected capacity change from 0 to 20971520
BTRFS: device fsid 15aa1203-98d3-4a66-bcae-ca82f629c2cd devid 1 transid 5 /dev/loop1 scanned by mkfs.btrfs (1863)
BTRFS: device fsid 15aa1203-98d3-4a66-bcae-ca82f629c2cd devid 2 transid 5 /dev/loop2 scanned by mkfs.btrfs (1863)
BTRFS info (device loop1): flagging fs with big metadata feature
BTRFS info (device loop1): allowing degraded mounts
BTRFS info (device loop1): disk space caching is enabled
BTRFS info (device loop1): has skinny extents
BTRFS info (device loop1): before clear_missing.00000000975bd577 /dev/loop1 0
BTRFS warning (device loop1): devid 2 uuid 8b333791-0b3f-4f57-b449-1c1ab6b51f38 is missing
BTRFS info (device loop1): before clear_missing.0000000000000000 /dev/loop2 1
BTRFS info (device loop1): checking UUID tree
BTRFS info (device loop1): flagging fs with big metadata feature
BTRFS info (device loop1): allowing degraded mounts
BTRFS info (device loop1): disk space caching is enabled
BTRFS info (device loop1): has skinny extents
BTRFS info (device loop1): before clear_missing.00000000975bd577 /dev/loop1 0
BTRFS warning (device loop1): devid 2 uuid 8b333791-0b3f-4f57-b449-1c1ab6b51f38 is missing
BTRFS info (device loop1): before clear_missing.0000000000000000 /dev/loop2 1
BTRFS info (device loop1): flagging fs with big metadata feature
BTRFS info (device loop1): allowing degraded mounts
BTRFS info (device loop1): disk space caching is enabled
BTRFS info (device loop1): has skinny extents
BTRFS info (device loop1): before clear_missing.00000000975bd577 /dev/loop1 0
BTRFS warning (device loop1): devid 2 uuid 8b333791-0b3f-4f57-b449-1c1ab6b51f38 is missing
BTRFS info (device loop1): before clear_missing.0000000000000000 /dev/loop2 1
CC: stable@vger.kernel.org # 4.19+
Signed-off-by: Li Zhang <zhanglikernel@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 42f2611cc1 ]
RDMA ULPs should only perform DMA through the ib_dma_* API instead of
using the hidden dma_device directly. In addition using the dma coherent
API family that dmapool is a part of can be very ineffcient on plaforms
that are not DMA coherent. Switch to use slab allocations and the
ib_dma_* APIs instead.
Link: https://lore.kernel.org/r/20201106181941.1878556-6-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4a146c7cf ]
The value of llc_testlink_time is set to the value stored in
net->ipv4.sysctl_tcp_keepalive_time when linkgroup init. The value of
sysctl_tcp_keepalive_time is already jiffies, so we don't need to
multiply by HZ, which would cause smc_link->llc_testlink_time overflow,
and test_link send flood.
Signed-off-by: Tony Lu <tonylu@linux.alibaba.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Reviewed-by: Wen Gu <guwen@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90a881fc35 ]
MTU change is refused whenever the value of new MTU is bigger than
the max packet bytes that fits in NFP Cluster Target Memory (CTM).
However, an eBPF program doesn't always need to access the whole
packet data.
The maximum direct packet access (DPA) offset has always been
caculated by verifier and stored in the max_pkt_offset field of prog
aux data.
Signed-off-by: Yu Xiao <yu.xiao@corigine.com>
Reviewed-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Reviewed-by: Niklas Soderlund <niklas.soderlund@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9159f10240 ]
The netif_device_detach() conditionally stops all tx queues if the queues
are running. There is no need to call netif_tx_stop_all_queues() again.
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86aeda32b8 ]
Pass the correct length to nvmet_tcp_verify_hdgst, which is the pdu
header length. This fixes a wrong behaviour where header digest
verification passes although the digest is wrong.
Signed-off-by: Amit Engel <amit.engel@dell.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9586e67b91 ]
When dispatching a zone append write request to a SCSI zoned block device,
if the target zone of the request is already locked, the device driver will
return BLK_STS_ZONE_RESOURCE and the request will be pushed back to the
hctx dipatch queue. The queue will be marked as RESTART in
dd_finish_request() and restarted in __blk_mq_free_request(). However, this
restart applies to the hctx of the completed request. If the requeued
request is on a different hctx, dispatch will no be retried until another
request is submitted or the next periodic queue run triggers, leading to up
to 30 seconds latency for the requeued request.
Fix this problem by scheduling a queue restart similarly to the
BLK_STS_RESOURCE case or when we cannot get the budget.
Also, consolidate the checks into the "need_resource" variable to simplify
the condition.
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Niklas Cassel <Niklas.Cassel@wdc.com>
Link: https://lore.kernel.org/r/20211026165127.4151055-1-naohiro.aota@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9122a70a63 ]
During a testing of an user-space application which transmits UDP
multicast datagrams and utilizes multicast routing to send the UDP
datagrams out of defined network interfaces, I've found a multicast
router does not fill-in UDP checksum into locally produced, looped-back
and forwarded UDP datagrams, if an original output NIC the datagrams
are sent to has UDP TX checksum offload enabled.
The datagrams are sent malformed out of the NIC the datagrams have been
forwarded to.
It is because:
1. If TX checksum offload is enabled on the output NIC, UDP checksum
is not calculated by kernel and is not filled into skb data.
2. dev_loopback_xmit(), which is called solely by
ip_mc_finish_output(), sets skb->ip_summed = CHECKSUM_UNNECESSARY
unconditionally.
3. Since 35fc92a9 ("[NET]: Allow forwarding of ip_summed except
CHECKSUM_COMPLETE"), the ip_summed value is preserved during
forwarding.
4. If ip_summed != CHECKSUM_PARTIAL, checksum is not calculated during
a packet egress.
The minimum fix in dev_loopback_xmit():
1. Preserves skb->ip_summed CHECKSUM_PARTIAL. This is the
case when the original output NIC has TX checksum offload enabled.
The effects are:
a) If the forwarding destination interface supports TX checksum
offloading, the NIC driver is responsible to fill-in the
checksum.
b) If the forwarding destination interface does NOT support TX
checksum offloading, checksums are filled-in by kernel before
skb is submitted to the NIC driver.
c) For local delivery, checksum validation is skipped as in the
case of CHECKSUM_UNNECESSARY, thanks to skb_csum_unnecessary().
2. Translates ip_summed CHECKSUM_NONE to CHECKSUM_UNNECESSARY. It
means, for CHECKSUM_NONE, the behavior is unmodified and is there
to skip a looped-back packet local delivery checksum validation.
Signed-off-by: Cyril Strejc <cyril.strejc@skoda.cz>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 926245c7d2 ]
page_frag_free() won't completely release the memory
allocated for the commands, the cache page must be explicitly
freed by calling __page_frag_cache_drain().
This bug can be easily reproduced by repeatedly
executing the following command on the initiator:
$echo 1 > /sys/devices/virtual/nvme-fabrics/ctl/nvme0/reset_controller
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: John Meneghini <jmeneghi@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 042b2046d0 ]
The tx queues are not stopped during the live migration. As a result, the
ndo_start_xmit() may access netfront_info->queues which is freed by
talk_to_netback()->xennet_destroy_queues().
This patch is to netif_device_detach() at the beginning of xen-netfront
resuming, and netif_device_attach() at the end of resuming.
CPU A CPU B
talk_to_netback()
-> if (info->queues)
xennet_destroy_queues(info);
to free netfront_info->queues
xennet_start_xmit()
to access netfront_info->queues
-> err = xennet_create_queues(info, &num_queues);
The idea is borrowed from virtio-net.
Cc: Joe Jin <joe.jin@oracle.com>
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 162079f2dc ]
The Winbond MMC driver fails to build on ARCH=m68k so prevent
that build config. Silences these build errors:
../drivers/mmc/host/wbsd.c: In function 'wbsd_request_end':
../drivers/mmc/host/wbsd.c:212:28: error: implicit declaration of function 'claim_dma_lock' [-Werror=implicit-function-declaration]
212 | dmaflags = claim_dma_lock();
../drivers/mmc/host/wbsd.c:215:17: error: implicit declaration of function 'release_dma_lock'; did you mean 'release_task'? [-Werror=implicit-function-declaration]
215 | release_dma_lock(dmaflags);
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211017175949.23838-1-rdunlap@infradead.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55dd7e0590 ]
Commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e rx/tx delay
config") sets the RX/TX delay according to the phy-mode property in the
device tree. For the A20-olinuxino-lime2 board this is "rgmii", which is the
wrong setting.
Following the example of a900cac375 ("ARM: dts: sun7i: a20: bananapro:
Fix ethernet phy-mode") the phy-mode is changed to "rgmii-id" which gets
the Ethernet working again on this board.
Signed-off-by: Bastien Roucariès <rouca@debian.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210916081721.237137-1-rouca@debian.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8017c99680 ]
On arm64 randconfig builds, hyperv sometimes fails with this
error:
In file included from drivers/hv/hv_trace.c:3:
In file included from drivers/hv/hyperv_vmbus.h:16:
In file included from arch/arm64/include/asm/sync_bitops.h:5:
arch/arm64/include/asm/bitops.h:11:2: error: only <linux/bitops.h> can be included directly
In file included from include/asm-generic/bitops/hweight.h:5:
include/asm-generic/bitops/arch_hweight.h:9:9: error: implicit declaration of function '__sw_hweight32' [-Werror,-Wimplicit-function-declaration]
include/asm-generic/bitops/atomic.h:17:7: error: implicit declaration of function 'BIT_WORD' [-Werror,-Wimplicit-function-declaration]
Include the correct header first.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211018131929.2260087-1-arnd@kernel.org
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf6abf345d ]
Use pci_info instead to avoid unnamed/uninitialized noise:
[197088.688729] sfc 0000:01:00.0: Solarflare NIC detected
[197088.690333] sfc 0000:01:00.0: Part Number : SFN5122F
[197088.729061] sfc 0000:01:00.0 (unnamed net_device) (uninitialized): no SR-IOV VFs probed
[197088.729071] sfc 0000:01:00.0 (unnamed net_device) (uninitialized): no PTP support
Inspired by fa44821a4d ("sfc: don't use netif_info et al before
net_device is registered") from Heiner Kallweit.
Signed-off-by: Erik Ekman <erik@kryo.se>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c62041c5ba ]
The 1/10GbaseT modes were set up for cards with SFP+ cages in
3497ed8c85 ("sfc: report supported link speeds on SFP connections").
10GbaseT was likely used since no 10G fibre mode existed.
The missing fibre modes for 1/10G were added to ethtool.h in 5711a98221
("net: ethtool: add support for 1000BaseX and missing 10G link modes")
shortly thereafter.
The user guide available at https://support-nic.xilinx.com/wp/drivers
lists support for the following cable and transceiver types in section 2.9:
- QSFP28 100G Direct Attach Cables
- QSFP28 100G SR Optical Transceivers (with SR4 modules listed)
- SFP28 25G Direct Attach Cables
- SFP28 25G SR Optical Transceivers
- QSFP+ 40G Direct Attach Cables
- QSFP+ 40G Active Optical Cables
- QSFP+ 40G SR4 Optical Transceivers
- QSFP+ to SFP+ Breakout Direct Attach Cables
- QSFP+ to SFP+ Breakout Active Optical Cables
- SFP+ 10G Direct Attach Cables
- SFP+ 10G SR Optical Transceivers
- SFP+ 10G LR Optical Transceivers
- SFP 1000BASE‐T Transceivers
- 1G Optical Transceivers
(From user guide issue 28. Issue 16 which also includes older cards like
SFN5xxx/SFN6xxx has matching lists for 1/10/40G transceiver types.)
Regarding SFP+ 10GBASE‐T transceivers the latest guide says:
"Solarflare adapters do not support 10GBASE‐T transceiver modules."
Tested using SFN5122F-R7 (with 2 SFP+ ports). Supported link modes do not change
depending on module used (tested with 1000BASE-T, 1000BASE-BX10, 10GBASE-LR).
Before:
$ ethtool ext
Settings for ext:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseT/Full
10000baseT/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Link partner advertised link modes: Not reported
Link partner advertised pause frame use: No
Link partner advertised auto-negotiation: No
Link partner advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Auto-negotiation: off
Port: FIBRE
PHYAD: 255
Transceiver: internal
Current message level: 0x000020f7 (8439)
drv probe link ifdown ifup rx_err tx_err hw
Link detected: yes
After:
$ ethtool ext
Settings for ext:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseT/Full
1000baseX/Full
10000baseCR/Full
10000baseSR/Full
10000baseLR/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Link partner advertised link modes: Not reported
Link partner advertised pause frame use: No
Link partner advertised auto-negotiation: No
Link partner advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Auto-negotiation: off
Port: FIBRE
PHYAD: 255
Transceiver: internal
Supports Wake-on: g
Wake-on: d
Current message level: 0x000020f7 (8439)
drv probe link ifdown ifup rx_err tx_err hw
Link detected: yes
Signed-off-by: Erik Ekman <erik@kryo.se>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c69b2f4687 ]
During the process of driver probing, the probe function should return < 0
for failure, otherwise, the kernel will treat value > 0 as success.
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e211210098 ]
During the process of driver probing, the probe function should return < 0
for failure, otherwise, the kernel will treat value > 0 as success.
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a8f71014b ]
The sgl is freed in the target stack in target_release_cmd_kref() before
calling qlt_free_cmd() but there is an unmap of sgl in qlt_free_cmd() that
causes a panic if sgl is not yet DMA unmapped:
NIP dma_direct_unmap_sg+0xdc/0x180
LR dma_direct_unmap_sg+0xc8/0x180
Call Trace:
ql_dbg_prefix+0x68/0xc0 [qla2xxx] (unreliable)
dma_unmap_sg_attrs+0x54/0xf0
qlt_unmap_sg.part.19+0x54/0x1c0 [qla2xxx]
qlt_free_cmd+0x124/0x1d0 [qla2xxx]
tcm_qla2xxx_release_cmd+0x4c/0xa0 [tcm_qla2xxx]
target_put_sess_cmd+0x198/0x370 [target_core_mod]
transport_generic_free_cmd+0x6c/0x1b0 [target_core_mod]
tcm_qla2xxx_complete_free+0x6c/0x90 [tcm_qla2xxx]
The sgl may be left unmapped in error cases of response sending. For
instance, qlt_rdy_to_xfer() maps sgl and exits when session is being
deleted keeping the sgl mapped.
This patch removes use-after-free of the sgl and ensures that the sgl is
unmapped for any command that was not sent to firmware.
Link: https://lore.kernel.org/r/20211018122650.11846-1-d.bogdanov@yadro.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Dmitry Bogdanov <d.bogdanov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2cddb44bd ]
During the process of driver probing, the probe function should return < 0
for failure, otherwise, the kernel will treat value > 0 as success.
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d94befbb5a ]
In laptop 'HP Spectre x360 Convertible 15-eb1xxx/8811' both front and
rear speakers are silent, this patch fixes that by overriding the pin
layout and by initializing the amplifier which needs a GPIO pin to be
set to 1 then 0, similar to the existing HP Spectre x360 14 model.
In order to have volume control, both front and rear speakers were
forced to use the DAC1.
This patch also correctly map the mute LED but since there is no
microphone on/off switch exposed by the alsa subsystem it never turns
on by itself.
There are still known audio issues in this laptop: headset microphone
doesn't work, the button to mute/unmute microphone is not yet mapped,
the LED of the mute/unmute speakers doesn't seems to be exposed via
GPIO and never turns on.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=213953
Signed-off-by: Davide Baldo <davide@baldo.me>
Link: https://lore.kernel.org/r/20211015072121.5287-1-davide@baldo.me
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c448b7aa3e ]
'component' is allocated in snd_soc_register_component(), but component->list
is not initalized, this may cause snd_soc_del_component_unlocked() deref null
ptr in the error handing case.
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
RIP: 0010:__list_del_entry_valid+0x81/0xf0
Call Trace:
snd_soc_del_component_unlocked+0x69/0x1b0 [snd_soc_core]
snd_soc_add_component.cold+0x54/0x6c [snd_soc_core]
snd_soc_register_component+0x70/0x90 [snd_soc_core]
devm_snd_soc_register_component+0x5e/0xd0 [snd_soc_core]
tas2552_probe+0x265/0x320 [snd_soc_tas2552]
? tas2552_component_probe+0x1e0/0x1e0 [snd_soc_tas2552]
i2c_device_probe+0xa31/0xbe0
Fix by adding INIT_LIST_HEAD() to snd_soc_component_initialize().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20211009065840.3196239-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6ff53f6a43 upstream.
Add a synchronize_rcu() after clearing the posted interrupt wakeup handler
to ensure all readers, i.e. in-flight IRQ handlers, see the new handler
before returning to the caller. If the caller is an exiting module and
is unregistering its handler, failure to wait could result in the IRQ
handler jumping into an unloaded module.
The registration path doesn't require synchronization, as it's the
caller's responsibility to not generate interrupts it cares about until
after its handler is registered.
Fixes: f6b3c72c23 ("x86/irq: Define a global vector for VT-d Posted-Interrupts")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211009001107.3936588-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 415de44076 upstream.
Currently, Linux probes for X86_BUG_NULL_SEL unconditionally which
makes it unsafe to migrate in a virtualised environment as the
properties across the migration pool might differ.
To be specific, the case which goes wrong is:
1. Zen1 (or earlier) and Zen2 (or later) in a migration pool
2. Linux boots on Zen2, probes and finds the absence of X86_BUG_NULL_SEL
3. Linux is then migrated to Zen1
Linux is now running on a X86_BUG_NULL_SEL-impacted CPU while believing
that the bug is fixed.
The only way to address the problem is to fully trust the "no longer
affected" CPUID bit when virtualised, because in the above case it would
be clear deliberately to indicate the fact "you might migrate to
somewhere which has this behaviour".
Zen3 adds the NullSelectorClearsBase CPUID bit to indicate that loading
a NULL segment selector zeroes the base and limit fields, as well as
just attributes. Zen2 also has this behaviour but doesn't have the NSCB
bit.
[ bp: Minor touchups. ]
Signed-off-by: Jane Malalane <jane.malalane@citrix.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
CC: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20211021104744.24126-1-jane.malalane@citrix.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7d445ab26 upstream.
When runtime support for converting between 4-level and 5-level pagetables
was added to the kernel, the SME code that built pagetables was updated
to use the pagetable functions, e.g. p4d_offset(), etc., in order to
simplify the code. However, the use of the pagetable functions in early
boot code requires the use of the USE_EARLY_PGTABLE_L5 #define in order to
ensure that the proper definition of pgtable_l5_enabled() is used.
Without the #define, pgtable_l5_enabled() is #defined as
cpu_feature_enabled(X86_FEATURE_LA57). In early boot, the CPU features
have not yet been discovered and populated, so pgtable_l5_enabled() will
return false even when 5-level paging is enabled. This causes the SME code
to always build 4-level pagetables to perform the in-place encryption.
If 5-level paging is enabled, switching to the SME pagetables results in
a page-fault that kills the boot.
Adding the #define results in pgtable_l5_enabled() using the
__pgtable_l5_enabled variable set in early boot and the SME code building
pagetables for the proper paging level.
Fixes: aad983913d ("x86/mm/encrypt: Simplify sme_populate_pgd() and sme_populate_pgd_large()")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: <stable@vger.kernel.org> # 4.18.x
Link: https://lkml.kernel.org/r/2cb8329655f5c753905812d951e212022a480475.1634318656.git.thomas.lendacky@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 712a951025 upstream.
It is possible to trigger a crash by splicing anon pipe bufs to the fuse
device.
The reason for this is that anon_pipe_buf_release() will reuse buf->page if
the refcount is 1, but that page might have already been stolen and its
flags modified (e.g. PG_lru added).
This happens in the unlikely case of fuse_dev_splice_write() getting around
to calling pipe_buf_release() after a page has been stolen, added to the
page cache and removed from the page cache.
Fix by calling pipe_buf_release() right after the page was inserted into
the page cache. In this case the page has an elevated refcount so any
release function will know that the page isn't reusable.
Reported-by: Frank Dinoff <fdinoff@google.com>
Link: https://lore.kernel.org/r/CAAmZXrsGg2xsP1CK+cbuEMumtrqdvD-NKnWzhNcvn71RV3c1yw@mail.gmail.com/
Fixes: dd3bb14f44 ("fuse: support splice() writing to fuse device")
Cc: <stable@vger.kernel.org> # v2.6.35
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1811bc401a upstream.
After we drop i_data sem, we need to reload the ext4_ext_path
structure since the extent tree can change once i_data_sem is
released.
This addresses the BUG:
[52117.465187] ------------[ cut here ]------------
[52117.465686] kernel BUG at fs/ext4/extents.c:1756!
...
[52117.478306] Call Trace:
[52117.478565] ext4_ext_shift_extents+0x3ee/0x710
[52117.479020] ext4_fallocate+0x139c/0x1b40
[52117.479405] ? __do_sys_newfstat+0x6b/0x80
[52117.479805] vfs_fallocate+0x151/0x4b0
[52117.480177] ksys_fallocate+0x4a/0xa0
[52117.480533] __x64_sys_fallocate+0x22/0x30
[52117.480930] do_syscall_64+0x35/0x80
[52117.481277] entry_SYSCALL_64_after_hwframe+0x44/0xae
[52117.481769] RIP: 0033:0x7fa062f855ca
Cc: stable@kernel.org
Link: https://lore.kernel.org/r/20210903062748.4118886-4-yangerkun@huawei.com
Signed-off-by: yangerkun <yangerkun@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39fec6889d upstream.
Ext4 file system has default lazy inode table initialization setup once
it is mounted. However, it has issue on computing the next schedule time
that makes the timeout same amount in jiffies but different real time in
secs if with various HZ values. Therefore, fix by measuring the current
time in a more granular unit nanoseconds and make the next schedule time
independent of the HZ value.
Fixes: bfff68738f ("ext4: add support for lazy inode table initialization")
Signed-off-by: Shaoying Xu <shaoyi@amazon.com>
Cc: stable@vger.kernel.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Link: https://lore.kernel.org/r/20210902164412.9994-2-shaoyi@amazon.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0317c0e87 upstream.
When the timer instance was add into ack_list but was not currently in
process, the user could stop it via snd_timer_stop1() without delete it
from the ack_list. Then the user could free the timer instance and when
it was actually processed UAF occurred.
This issue could be reproduced via testcase snd_timer01 in ltp - running
several instances of that testcase at the same time.
What I actually met was that the ack_list of the timer broken and the
kernel went into deadloop with irqoff. That could be detected by
hardlockup detector on board or when we run it on qemu, we could use gdb
to dump the ack_list when the console has no response.
To fix this issue, we delete the timer instance from ack_list and
active_list unconditionally in snd_timer_stop1().
Signed-off-by: Wang Wensheng <wangwensheng4@huawei.com>
Suggested-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211103033517.80531-1-wangwensheng4@huawei.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39173303c8 upstream.
The recent change in hda-intel driver to allow repeated probes
surfaced a problem that has been hidden until; the probe process in
the work calls azx_free() at the error path, and this skips the card
free process that eventually releases codec instances. As a result,
we get a kernel WARNING like:
snd_hda_intel 0000:00:1f.3: Cannot probe codecs, giving up
------------[ cut here ]------------
WARNING: CPU: 14 PID: 186 at sound/hda/hdac_bus.c:73
....
For fixing this, we need to call snd_card_free() instead of
azx_free(). Additionally, the device drvdata has to be cleared, as
the driver binding itself is still active. Then the PM and other
driver callbacks will ignore the procedure.
Fixes: c0f1886de7 ("ALSA: hda: intel: Allow repeatedly probing on codec configuration errors")
Reported-and-tested-by: Scott Branden <scott.branden@broadcom.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/063e2397-7edb-5f48-7b0d-618b938d9dd8@broadcom.com
Link: https://lore.kernel.org/r/20211110194633.19098-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f27b68906 upstream.
Adding the Line6 HX-Stomp XL USB_ID as it needs this fixed frequency
quirk as well.
The device is basically just the HX-Stomp with some more buttons on
the face. I've done some recording with it after adding it, and it
seems to function properly with this fix. The Midi features appear to
be working as well.
[ a coding style fix and patch reformat by tiwai ]
Signed-off-by: Jason Ormes <skryking@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211030200405.1358678-1-skryking@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 55f261b73a upstream.
Add the missing endpoint max-packet sanity check to probe() to avoid
division by zero in alloc_stream_buffers() in case a malicious device
has broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4f ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: 63978ab3e3 ("sound: add Edirol UA-101 support")
Cc: stable@vger.kernel.org # 2.6.34
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211026095401.26522-1-johan@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 861f92cb91 upstream.
Drivers that do not use the ctrl-framework use this function instead.
Fix the following issues:
- Do not check for multiple classes when getting the DEF_VAL.
- Return -EINVAL for request_api calls
- Default value cannot be changed, return EINVAL as soon as possible.
- Return the right error_idx
[If an error is found when validating the list of controls passed with
VIDIOC_G_EXT_CTRLS, then error_idx shall be set to ctrls->count to
indicate to userspace that no actual hardware was touched.
It would have been much nicer of course if error_idx could point to the
control index that failed the validation, but sadly that's not how the
API was designed.]
Fixes v4l2-compliance:
Control ioctls (Input 0):
warn: v4l2-test-controls.cpp(834): error_idx should be equal to count
warn: v4l2-test-controls.cpp(855): error_idx should be equal to count
fail: v4l2-test-controls.cpp(813): doioctl(node, VIDIOC_G_EXT_CTRLS, &ctrls)
test VIDIOC_G/S/TRY_EXT_CTRLS: FAIL
Buffer ioctls (Input 0):
fail: v4l2-test-buffers.cpp(1994): ret != EINVAL && ret != EBADR && ret != ENOTTY
test Requests: FAIL
Cc: stable@vger.kernel.org
Fixes: 6fa6f831f0 ("media: v4l2-ctrls: add core request support")
Suggested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0887e9e152 upstream.
The mem-to-mem stateless decoder API specifies support for dynamic
resolution changes. In particular, the decoder should accept format
changes on the OUTPUT queue even when buffers have been allocated,
as long as it is not streaming.
Relax restrictions for S_FMT as described in the previous paragraph,
and as long as the codec format remains the same. This aligns it with
the Hantro and Cedrus decoders. This change was mostly based on commit
ae02d49493 ("media: hantro: Fix s_fmt for dynamic resolution changes").
Since rkvdec_s_fmt() is now just a wrapper around the output/capture
variants without any additional shared functionality, drop the wrapper
and call the respective functions directly.
Fixes: cd33c83044 ("media: rkvdec: Add the rkvdec driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 298d8e8f7b upstream.
The rkvdec H.264 decoder currently overrides sizeimage for the output
format. This causes issues when userspace requires and requests a larger
buffer, but ends up with one of insufficient size.
Instead, only provide a default size if none was requested. This fixes
the video_decode_accelerator_tests from Chromium failing on the first
frame due to insufficient buffer space. It also aligns the behavior
of the rkvdec driver with the Hantro and Cedrus drivers.
Fixes: cd33c83044 ("media: rkvdec: Add the rkvdec driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2ac5fb35cd upstream.
sizeof when applied to a pointer typed expression gives the size of
the pointer.
./drivers/firmware/psci/psci_checker.c:158:41-47: ERROR application of sizeof to pointer
This issue was detected with the help of Coccinelle.
Fixes: 7401056de5 ("drivers/firmware: psci_checker: stash and use topology_core_cpumask for hotplug tests")
Cc: stable@vger.kernel.org
Reported-by: Zeal Robot <zealci@zte.com.cn>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: jing yangyang <jing.yangyang@zte.com.cn>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8779e05ba8 upstream.
The TIF_XXX flags are stored in the flags field in the thread_info
struct (TI_FLAGS), not in the flags field of the task_struct structure
(TASK_FLAGS).
It seems this bug didn't generate any important side-effects, otherwise it
wouldn't have went unnoticed for 12 years (since v2.6.32).
Signed-off-by: Helge Deller <deller@gmx.de>
Fixes: ecd3d4bc06 ("parisc: stop using task->ptrace for {single,block}step flags")
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e866a4628 upstream.
Fix a kernel crash which happens on PA1.x CPUs while initializing the
FTRACE/KPROBE breakpoints. The PTE table entries for the fixmap area
were not created correctly.
Signed-off-by: Helge Deller <deller@gmx.de>
Fixes: ccfbc68d41 ("parisc: add set_fixmap()/clear_fixmap()")
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c336d6e33 upstream.
When calculating i_blocks, there was a mistake that was masked with a
32-bit variable. So i_blocks for files larger than 4 GiB had incorrect
values. Mask with a 64-bit variable instead of 32-bit one.
Fixes: 5f2aa07507 ("exfat: add inode operations")
Cc: stable@vger.kernel.org # v5.7+
Reported-by: Ganapathi Kamath <hgkamath@hotmail.com>
Signed-off-by: Sungjong Seo <sj1557.seo@samsung.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 43592c8736 upstream.
Only wait for DRTO on reads, otherwise the driver hangs.
The driver prevents sending CMD12 on response errors like CRCs. According
to the comment this is because some cards have problems with this during
the UHS tuning sequence. Unfortunately this workaround currently also
applies for any command with data. On reads this will set the drto timer,
which then triggers after a while. On writes this will not set any timer
and the tasklet will not be scheduled again.
I cannot test for the UHS workarounds need, but even if so, it should at
most apply to reads. I have observed many hangs when CMD25 response
contained a CRC error. This patch fixes this without touching the actual
UHS tuning workaround.
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/af8f8b8674ba4fcc9a781019e4aeb72c@hyperstone.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 703535e6ae upstream.
No need to deduce command size in scsi_setup_scsi_cmnd() anymore as
appropriate checks have been added to scsi_fill_sghdr_rq() function and the
cmd_len should never be zero here. The code to do that wasn't correct
anyway, as it used uninitialized cmd->cmnd, which caused a null-ptr-deref
if the command size was zero as in the trace below. Fix this by removing
the unneeded code.
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
CPU: 0 PID: 1822 Comm: repro Not tainted 5.15.0 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-4.fc34 04/01/2014
Call Trace:
blk_mq_dispatch_rq_list+0x7c7/0x12d0
__blk_mq_sched_dispatch_requests+0x244/0x380
blk_mq_sched_dispatch_requests+0xf0/0x160
__blk_mq_run_hw_queue+0xe8/0x160
__blk_mq_delay_run_hw_queue+0x252/0x5d0
blk_mq_run_hw_queue+0x1dd/0x3b0
blk_mq_sched_insert_request+0x1ff/0x3e0
blk_execute_rq_nowait+0x173/0x1e0
blk_execute_rq+0x15c/0x540
sg_io+0x97c/0x1370
scsi_ioctl+0xe16/0x28e0
sd_ioctl+0x134/0x170
blkdev_ioctl+0x362/0x6e0
block_ioctl+0xb0/0xf0
vfs_ioctl+0xa7/0xf0
do_syscall_64+0x3d/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
---[ end trace 8b086e334adef6d2 ]---
Kernel panic - not syncing: Fatal exception
Link: https://lore.kernel.org/r/20211103170659.22151-2-tadeusz.struk@linaro.org
Fixes: 2ceda20f0a ("scsi: core: Move command size detection out of the fast path")
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: James E.J. Bottomley <jejb@linux.ibm.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: <linux-scsi@vger.kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Cc: <stable@vger.kernel.org> # 5.15, 5.14, 5.10
Reported-by: syzbot+5516b30f5401d4dcbcae@syzkaller.appspotmail.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tadeusz Struk <tadeusz.struk@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 839b63860e upstream.
Patch series "ocfs2: Truncate data corruption fix".
As further testing has shown, commit 5314454ea3 ("ocfs2: fix data
corruption after conversion from inline format") didn't fix all the data
corruption issues the customer started observing after 6dbf7bb555
("fs: Don't invalidate page buffers in block_write_full_page()") This
time I have tracked them down to two bugs in ocfs2 truncation code.
One bug (truncating page cache before clearing tail cluster and setting
i_size) could cause data corruption even before 6dbf7bb555, but before
that commit it needed a race with page fault, after 6dbf7bb555 it
started to be pretty deterministic.
Another bug (zeroing pages beyond old i_size) used to be harmless
inefficiency before commit 6dbf7bb555. But after commit 6dbf7bb555
in combination with the first bug it resulted in deterministic data
corruption.
Although fixing only the first problem is needed to stop data
corruption, I've fixed both issues to make the code more robust.
This patch (of 2):
ocfs2_truncate_file() did unmap invalidate page cache pages before
zeroing partial tail cluster and setting i_size. Thus some pages could
be left (and likely have left if the cluster zeroing happened) in the
page cache beyond i_size after truncate finished letting user possibly
see stale data once the file was extended again. Also the tail cluster
zeroing was not guaranteed to finish before truncate finished causing
possible stale data exposure. The problem started to be particularly
easy to hit after commit 6dbf7bb555 "fs: Don't invalidate page buffers
in block_write_full_page()" stopped invalidation of pages beyond i_size
from page writeback path.
Fix these problems by unmapping and invalidating pages in the page cache
after the i_size is reduced and tail cluster is zeroed out.
Link: https://lkml.kernel.org/r/20211025150008.29002-1-jack@suse.cz
Link: https://lkml.kernel.org/r/20211025151332.11301-1-jack@suse.cz
Fixes: ccd979bdbc ("[PATCH] OCFS2: The Second Oracle Cluster Filesystem")
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68dbbe7d5b upstream.
Some ATA drives are very slow to respond to READ_LOG_EXT and
READ_LOG_DMA_EXT commands issued from ata_dev_configure() when the
device is revalidated right after resuming a system or inserting the
ATA adapter driver (e.g. ahci). The default 5s timeout
(ATA_EH_CMD_DFL_TIMEOUT) used for these commands is too short, causing
errors during the device configuration. Ex:
...
ata9: SATA max UDMA/133 abar m524288@0x9d200000 port 0x9d200400 irq 209
ata9: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
ata9.00: ATA-9: XXX XXXXXXXXXXXXXXX, XXXXXXXX, max UDMA/133
ata9.00: qc timeout (cmd 0x2f)
ata9.00: Read log page 0x00 failed, Emask 0x4
ata9.00: Read log page 0x00 failed, Emask 0x40
ata9.00: NCQ Send/Recv Log not supported
ata9.00: Read log page 0x08 failed, Emask 0x40
ata9.00: 27344764928 sectors, multi 16: LBA48 NCQ (depth 32), AA
ata9.00: Read log page 0x00 failed, Emask 0x40
ata9.00: ATA Identify Device Log not supported
ata9.00: failed to set xfermode (err_mask=0x40)
ata9: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
ata9.00: configured for UDMA/133
...
The timeout error causes a soft reset of the drive link, followed in
most cases by a successful revalidation as that give enough time to the
drive to become fully ready to quickly process the read log commands.
However, in some cases, this also fails resulting in the device being
dropped.
Fix this by using adding the ata_eh_revalidate_timeouts entries for the
READ_LOG_EXT and READ_LOG_DMA_EXT commands. This defines a timeout
increased to 15s, retriable one time.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52f8869337 upstream.
Since binder was integrated with selinux, it has passed
'struct task_struct' associated with the binder_proc
to represent the source and target of transactions.
The conversion of task to SID was then done in the hook
implementations. It turns out that there are race conditions
which can result in an incorrect security context being used.
Fix by using the 'struct cred' saved during binder_open and pass
it to the selinux subsystem.
Cc: stable@vger.kernel.org # 5.14 (need backport for earlier stables)
Fixes: 79af73079d ("Add security hooks to binder and implement the hooks for SELinux.")
Suggested-by: Jann Horn <jannh@google.com>
Signed-off-by: Todd Kjos <tkjos@google.com>
Acked-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29bc22ac5e upstream.
Save the 'struct cred' associated with a binder process
at initial open to avoid potential race conditions
when converting to an euid.
Set a transaction's sender_euid from the 'struct cred'
saved at binder_open() instead of looking up the euid
from the binder proc's 'struct task'. This ensures
the euid is associated with the security context that
of the task that opened binder.
Cc: stable@vger.kernel.org # 4.4+
Fixes: 457b9a6f09 ("Staging: android: add binder driver")
Signed-off-by: Todd Kjos <tkjos@google.com>
Suggested-by: Stephen Smalley <stephen.smalley.work@gmail.com>
Suggested-by: Jann Horn <jannh@google.com>
Acked-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e1959faf08 upstream.
Some USB 3.1 enumeration issues were reported after the hub driver removed
the minimum 100ms limit for the power-on-good delay.
Since commit 90d28fb53d ("usb: core: reduce power-on-good delay time of
root hub") the hub driver sets the power-on-delay based on the
bPwrOn2PwrGood value in the hub descriptor.
xhci driver has a 20ms bPwrOn2PwrGood value for both roothubs based
on xhci spec section 5.4.8, but it's clearly not enough for the
USB 3.1 devices, causing enumeration issues.
Tests indicate full 100ms delay is needed.
Reported-by: Walt Jr. Brake <mr.yming81@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Fixes: 90d28fb53d ("usb: core: reduce power-on-good delay time of root hub")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211105160036.549516-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 063a326cba.
Reverting temporarily because not enabling the composite output has
been seen to break HDMI on older Pis.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
It referenced fragment@13 which used to be part of edt-ft5406.dtsi,
but has now been removed.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The code that set the scdc_enabled flag to ensure it was
disabled at boot time also ran on Pi0-3 where there is no
SCDC support. This lead to a warning in vc4_hdmi_encoder_post_crtc_disable
due to vc4_hdmi_disable_scrambling being called and trying to
read (and write) register HDMI_SCRAMBLER_CTL which doesn't
exist on those platforms.
Only set the flag should the interface be configured to support
more than HDMI 1.4.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add a check to vc4_hvs_gamma_check to ensure a new non-empty
gamma LUT is of the correct length before accepting it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
edt-ft5406.dtsi is included from vc4-kms-dsi-7inch which was
also setting i2c0mux and i2c0if status fields. This meant that
dtoverlay wouldn't apply the overlay due to multiple fragments
changing the same parameter.
Move the enable from edt-ft5406.dtsi to edt-ft5406-overlay.dts
for when it should be needed as an independent overlay.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Two calls were made to drm_crtc_enable_color_mgmt to add gamma
and CTM, however they were both set to add the gamma properties,
so they ended up added twice.
Fixes: 766cc6b1f7 "drm/vc4: Add CTM support"
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
With HVS5 the gamma block is now only reprogrammed with
a disable/enable. Loading the table from vc4_hvs_init_channel
(called from vc4_hvs_atomic_enable) appears to be at an
invalid point in time and so isn't applied.
Switch to enabling and disabling the gamma table instead. This
isn't safe if the pipeline is running, but it isn't now.
For HVS4 it is safe to enable and disable dynamically, so
adopt that approach there too.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The code falls through to "fail" under all conditions, so there is no
need for the drm_property_blob_put if the gamma lut hasn't been changed.
Fixes: 9cca26674a "drm: Check whether the gamma lut has changed before updating"
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
commit a44f9d6f9d upstream.
There is a wrong comparison of the total size of the loaded firmware
css->fw->size with the size of a pointer to struct imgu_fw_header.
Turn binary_header into a flexible-array member[1][2], use the
struct_size() helper and fix the wrong size comparison. Notice
that the loaded firmware needs to contain at least one 'struct
imgu_fw_info' item in the binary_header[] array.
It's also worth mentioning that
"css->fw->size < struct_size(css->fwp, binary_header, 1)"
with binary_header declared as a flexible-array member is equivalent
to
"css->fw->size < sizeof(struct imgu_fw_header)"
with binary_header declared as a one-element array (as in the original
code).
The replacement of the one-element array with a flexible-array member
also helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.10/process/deprecated.html#zero-length-and-one-element-arrays
Link: https://github.com/KSPP/linux/issues/79
Link: https://github.com/KSPP/linux/issues/109
Fixes: 09d290f0ba ("media: staging/intel-ipu3: css: Add support for firmware management")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a56d3e40bd upstream.
USB bulk and interrupt message timeouts are specified in milliseconds
and should specifically not vary with CONFIG_HZ.
Note that the bulk-out transfer timeout was set to the endpoint
bInterval value, which should be ignored for bulk endpoints and is
typically set to zero. This meant that a failing bulk-out transfer
would never time out.
Assume that the 10 second timeout used for all other transfers is more
than enough also for the bulk-out endpoint.
Fixes: 985cafccbf ("Staging: Comedi: vmk80xx: Add k8061 support")
Fixes: 951348b377 ("staging: comedi: vmk80xx: wait for URBs to complete")
Cc: stable@vger.kernel.org # 2.6.31
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20211025114532.4599-6-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a23461c474 upstream.
The driver uses endpoint-sized USB transfer buffers but up until
recently had no sanity checks on the sizes.
Commit e1f13c879a ("staging: comedi: check validity of wMaxPacketSize
of usb endpoints found") inadvertently fixed NULL-pointer dereferences
when accessing the transfer buffers in case a malicious device has a
zero wMaxPacketSize.
Make sure to allocate buffers large enough to handle also the other
accesses that are done without a size check (e.g. byte 18 in
vmk80xx_cnt_insn_read() for the VMK8061_MODEL) to avoid writing beyond
the buffers, for example, when doing descriptor fuzzing.
The original driver was for a low-speed device with 8-byte buffers.
Support was later added for a device that uses bulk transfers and is
presumably a full-speed device with a maximum 64-byte wMaxPacketSize.
Fixes: 985cafccbf ("Staging: Comedi: vmk80xx: Add k8061 support")
Cc: stable@vger.kernel.org # 2.6.31
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20211025114532.4599-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 536de747bc upstream.
USB transfer buffers are typically mapped for DMA and must not be
allocated on the stack or transfers will fail.
Allocate proper transfer buffers in the various command helpers and
return an error on short transfers instead of acting on random stack
data.
Note that this also fixes a stack info leak on systems where DMA is not
used as 32 bytes are always sent to the device regardless of how short
the command is.
Fixes: 63274cd7d3 ("Staging: comedi: add usb dt9812 driver")
Cc: stable@vger.kernel.org # 2.6.29
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211027093529.30896-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c052cc1a06 upstream.
Syzbot reported use-after-free in rtl8712_dl_fw(). The problem was in
race condition between r871xu_dev_remove() ->ndo_open() callback.
It's easy to see from crash log, that driver accesses released firmware
in ->ndo_open() callback. It may happen, since driver was releasing
firmware _before_ unregistering netdev. Fix it by moving
unregister_netdev() before cleaning up resources.
Call Trace:
...
rtl871x_open_fw drivers/staging/rtl8712/hal_init.c:83 [inline]
rtl8712_dl_fw+0xd95/0xe10 drivers/staging/rtl8712/hal_init.c:170
rtl8712_hal_init drivers/staging/rtl8712/hal_init.c:330 [inline]
rtl871x_hal_init+0xae/0x180 drivers/staging/rtl8712/hal_init.c:394
netdev_open+0xe6/0x6c0 drivers/staging/rtl8712/os_intfs.c:380
__dev_open+0x2bc/0x4d0 net/core/dev.c:1484
Freed by task 1306:
...
release_firmware+0x1b/0x30 drivers/base/firmware_loader/main.c:1053
r871xu_dev_remove+0xcc/0x2c0 drivers/staging/rtl8712/usb_intf.c:599
usb_unbind_interface+0x1d8/0x8d0 drivers/usb/core/driver.c:458
Fixes: 8c213fa591 ("staging: r8712u: Use asynchronous firmware loading")
Cc: stable <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+c55162be492189fb4f51@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/20211019211718.26354-1-paskripkin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3cffa06aee upstream.
The commit 48021f9813 ("printk: handle blank console arguments
passed in.") prevented crash caused by empty console= parameter value.
Unfortunately, this value is widely used on Chromebooks to disable
the console output. The above commit caused performance regression
because the messages were pushed on slow console even though nobody
was watching it.
Use ttynull driver explicitly for console="" and console=null
parameters. It has been created for exactly this purpose.
It causes that preferred_console is set. As a result, ttySX and ttyX
are not used as a fallback. And only ttynull console gets registered by
default.
It still allows to register other consoles either by additional console=
parameters or SPCR. It prevents regression because it worked this way even
before. Also it is a sane semantic. Preventing output on all consoles
should be done another way, for example, by introducing mute_console
parameter.
Link: https://lore.kernel.org/r/20201006025935.GA597@jagdpanzerIV.localdomain
Suggested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20201111135450.11214-3-pmladek@suse.com
Cc: Yi Fan <yfa@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32e9f56a96 upstream.
When freeing txn buffers, binder_transaction_buffer_release()
attempts to detect whether the current context is the target by
comparing current->group_leader to proc->tsk. This is an unreliable
test. Instead explicitly pass an 'is_failure' boolean.
Detecting the sender was being used as a way to tell if the
transaction failed to be sent. When cleaning up after
failing to send a transaction, there is no need to close
the fds associated with a BINDER_TYPE_FDA object. Now
'is_failure' can be used to accurately detect this case.
Fixes: 44d8047f1d ("binder: use standard functions to allocate fds")
Cc: stable <stable@vger.kernel.org>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Todd Kjos <tkjos@google.com>
Link: https://lore.kernel.org/r/20211015233811.3532235-1-tkjos@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 21b5fcdccb upstream.
musb_gadget_queue() adds the passed request to musb_ep::req_list. If the
endpoint is idle and it is the first request then it invokes
musb_queue_resume_work(). If the function returns an error then the
error is passed to the caller without any clean-up and the request
remains enqueued on the list. If the caller enqueues the request again
then the list corrupts.
Remove the request from the list on error.
Fixes: ea2f35c01d ("usb: musb: Fix sleeping function called from invalid context for hdrc glue")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Viraj Shah <viraj.shah@linutronix.de>
Link: https://lore.kernel.org/r/20211021093644.4734-1-viraj.shah@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a0548b2690 upstream.
On 64-bit:
drivers/usb/gadget/udc/fsl_qe_udc.c: In function ‘qe_ep0_rx’:
drivers/usb/gadget/udc/fsl_qe_udc.c:842:13: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
842 | vaddr = (u32)phys_to_virt(in_be32(&bd->buf));
| ^
In file included from drivers/usb/gadget/udc/fsl_qe_udc.c:41:
drivers/usb/gadget/udc/fsl_qe_udc.c:843:28: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
843 | frame_set_data(pframe, (u8 *)vaddr);
| ^
The driver assumes physical and virtual addresses are 32-bit, hence it
cannot work on 64-bit platforms.
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20211027080849.3276289-1-geert@linux-m68k.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d5e7a28b1 upstream.
This is a new warning in clang top-of-tree (will be clang 14):
In file included from arch/x86/kvm/mmu/mmu.c:27:
arch/x86/kvm/mmu/spte.h:318:9: error: use of bitwise '|' with boolean operands [-Werror,-Wbitwise-instead-of-logical]
return __is_bad_mt_xwr(rsvd_check, spte) |
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
||
arch/x86/kvm/mmu/spte.h:318:9: note: cast one or both operands to int to silence this warning
The code is fine, but change it anyway to shut up this clever clogs
of a compiler.
Reported-by: torvic9@mailbox.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[nathan: Backport to 5.10, which does not have 961f84457c]
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On a Pi 4, enabling composite video disables the HDMI output. As a
consequence, the composite output is disabled by default. Change the
vc4-kms-v3d overlay used on older Pis to also disable composite by
default, replacing the "nocomposite" parameter with a "composite"
parameter.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
commit df0380b953 upstream.
This is a fix equivalent with the upstream commit df0380b953 ("ALSA:
usb-audio: Add quirk for Audient iD14"), adapted to the earlier
kernels up to 5.14.y. It adds the quirk entry with the old
ignore_ctl_error flag to the usbmix_ctl_maps, instead.
The original commit description says:
Audient iD14 (2708:0002) may get a control message error that
interferes the operation e.g. with alsactl. Add the quirk to ignore
such errors like other devices.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22390ce786 upstream.
This is a fix equivalent with the upstream commit 22390ce786 ("ALSA:
usb-audio: add Schiit Hel device to quirk table"), adapted to the
earlier kernels up to 5.14.y. It adds the quirk entry with the old
ignore_ctl_error flag to the usbmix_ctl_maps, instead.
The original patch description says:
The Shciit Hel device responds to the ctl message for the mic capture
switch with a timeout of -EPIPE:
usb 7-2.2: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x1100, type = 1
usb 7-2.2: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x1100, type = 1
usb 7-2.2: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x1100, type = 1
usb 7-2.2: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x1100, type = 1
This seems safe to ignore as the device works properly with the control
message quirk, so add it to the quirk table so all is good.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eb4f756915 upstream.
After commit 77a7300aba ("of/irq: Get rid of NO_IRQ usage"),
no irq case has been removed, irq_of_parse_and_map() will return
0 in all cases when get error from parse and map an interrupt into
linux virq space.
amba_device_register() is only used on no-DT initialization, see
s3c64xx_pl080_init() arch/arm/mach-s3c/pl080.c
ep93xx_init_devices() arch/arm/mach-ep93xx/core.c
They won't set -1 to irq[0], so no need the warn.
This reverts commit 2eac58d502.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 35d2969ea3 upstream.
The bounds checking in avc_ca_pmt() is not strict enough. It should
be checking "read_pos + 4" because it's reading 5 bytes. If the
"es_info_length" is non-zero then it reads a 6th byte so there needs to
be an additional check for that.
I also added checks for the "write_pos". I don't think these are
required because "read_pos" and "write_pos" are tied together so
checking one ought to be enough. But they make the code easier to
understand for me. The check on write_pos is:
if (write_pos + 4 >= sizeof(c->operand) - 4) {
The first "+ 4" is because we're writing 5 bytes and the last " - 4"
is to leave space for the CRC.
The other problem is that "length" can be invalid. It comes from
"data_length" in fdtv_ca_pmt().
Cc: stable@vger.kernel.org
Reported-by: Luo Likang <luolikang@nsfocus.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e8684db191 upstream.
The driver allocates skb during ndo_open with GFP_ATOMIC which has high chance of failure when there are multiple instances.
GFP_KERNEL is enough while open and use GFP_ATOMIC only from interrupt context.
Fixes: 23f0703c12 ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 55161e67d4 upstream.
This reverts commit 09e856d54b.
When an interface is enslaved in a VRF, prerouting conntrack hook is
called twice: once in the context of the original input interface, and
once in the context of the VRF interface. If no special precausions are
taken, this leads to creation of two conntrack entries instead of one,
and breaks SNAT.
Commit above was intended to avoid creation of extra conntrack entries
when input interface is enslaved in a VRF. It did so by resetting
conntrack related data associated with the skb when it enters VRF context.
However it breaks netfilter operation. Imagine a use case when conntrack
zone must be assigned based on the original input interface, rather than
VRF interface (that would make original interfaces indistinguishable). One
could create netfilter rules similar to these:
chain rawprerouting {
type filter hook prerouting priority raw;
iif realiface1 ct zone set 1 return
iif realiface2 ct zone set 2 return
}
This works before the mentioned commit, but not after: zone assignment
is "forgotten", and any subsequent NAT or filtering that is dependent
on the conntrack zone does not work.
Here is a reproducer script that demonstrates the difference in behaviour.
==========
#!/bin/sh
# This script demonstrates unexpected change of nftables behaviour
# caused by commit 09e856d54b ""vrf: Reset skb conntrack
# connection on VRF rcv"
# https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=09e856d54bda5f288ef8437a90ab2b9b3eab83d1
#
# Before the commit, it was possible to assign conntrack zone to a
# packet (or mark it for `notracking`) in the prerouting chanin, raw
# priority, based on the `iif` (interface from which the packet
# arrived).
# After the change, # if the interface is enslaved in a VRF, such
# assignment is lost. Instead, assignment based on the `iif` matching
# the VRF master interface is honored. Thus it is impossible to
# distinguish packets based on the original interface.
#
# This script demonstrates this change of behaviour: conntrack zone 1
# or 2 is assigned depending on the match with the original interface
# or the vrf master interface. It can be observed that conntrack entry
# appears in different zone in the kernel versions before and after
# the commit.
IPIN=172.30.30.1
IPOUT=172.30.30.2
PFXL=30
ip li sh vein >/dev/null 2>&1 && ip li del vein
ip li sh tvrf >/dev/null 2>&1 && ip li del tvrf
nft list table testct >/dev/null 2>&1 && nft delete table testct
ip li add vein type veth peer veout
ip li add tvrf type vrf table 9876
ip li set veout master tvrf
ip li set vein up
ip li set veout up
ip li set tvrf up
/sbin/sysctl -w net.ipv4.conf.veout.accept_local=1
/sbin/sysctl -w net.ipv4.conf.veout.rp_filter=0
ip addr add $IPIN/$PFXL dev vein
ip addr add $IPOUT/$PFXL dev veout
nft -f - <<__END__
table testct {
chain rawpre {
type filter hook prerouting priority raw;
iif { veout, tvrf } meta nftrace set 1
iif veout ct zone set 1 return
iif tvrf ct zone set 2 return
notrack
}
chain rawout {
type filter hook output priority raw;
notrack
}
}
__END__
uname -rv
conntrack -F
ping -W 1 -c 1 -I vein $IPOUT
conntrack -L
Signed-off-by: Eugene Crosser <crosser@average.org>
Acked-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 041c614882 upstream.
Everything except the first 32 bits was lost when the pause flags were
added. This makes the 50000baseCR2 mode flag (bit 34) not appear.
I have tested this with a 10G card (SFN5122F-R7) by modifying it to
return a non-legacy link mode (10000baseCR).
Signed-off-by: Erik Ekman <erik@kryo.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We currently rely on two functions, vc4_hdmi_supports_scrambling() and
vc4_hdmi_mode_needs_scrambling() to determine if we should enable and
disable the scrambler for any given mode.
Since we might need to disable the controller at boot, we also always
run vc4_hdmi_disable_scrambling() and thus call those functions without
a mode yet, which in turns need to make some special casing in order for
it to work.
Instead of duplicating the check for whether or not we need to take care
of the scrambler in both vc4_hdmi_enable_scrambling() and
vc4_hdmi_disable_scrambling(), we can do that check only when we enable
it and store whether or not it's been enabled in our private structure.
We also need to initialize that flag at true to make sure we disable the
scrambler at boot since we can't really know its state yet.
This allows to simplify a bit that part of the driver, and removes one
user of our copy of the CRTC adjusted mode outside of KMS (since
vc4_hdmi_disable_scrambling() might be called from the hotplug interrupt
handler).
It also removes our last user of the legacy encoder->crtc pointer.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
We currently poke at encoder->crtc in the ALSA code path to determine
whether the HDMI output is enabled or not, and thus whether we should
allow the audio output.
However, that pointer is deprecated and shouldn't really be used by
atomic drivers anymore. Since we have the infrastructure in place now,
let's just create a flag that we toggle to report whether the controller
is currently enabled and use that instead of encoder->crtc in ALSA.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Even though we already check that the encoder->crtc pointer is there
during in startup(), which is part of the open() path in ASoC, nothing
guarantees that our encoder state won't change between the time when we
open the device and the time we prepare it.
Move the sanity checks we do in startup() to a helper and call it from
prepare().
Fixes: 91e99e1139 ("drm/vc4: hdmi: Register HDMI codec")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Accessing the crtc->state pointer from outside the modesetting context
is not allowed. We thus need to copy whatever we need from the KMS state
to our structure in order to access it.
However, in the vc4 HDMI driver we do use that pointer in the ALSA code
path, and potentially in the hotplug interrupt handler path.
These paths both need access to the CRTC adjusted mode in order for the
proper dividers to be set for ALSA, and the scrambler state to be
reinstated properly for hotplug.
Let's copy this mode into our private encoder structure and reference it
from there when needed. Since that part is shared between KMS and other
paths, we need to protect it using our mutex.
Link: https://lore.kernel.org/all/YWgteNaNeaS9uWDe@phenom.ffwll.local/
Fixes: bb7d785688 ("drm/vc4: Add HDMI audio support")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The vc4 HDMI controller registers into the KMS, CEC and ALSA
frameworks.
However, no particular care is done to prevent the concurrent execution
of different framework hooks from happening at the same time.
In order to protect against that scenario, let's introduce a mutex that
relevant ALSA and KMS hooks will need to take to prevent concurrent
execution.
CEC is left out at the moment though, since the .get_modes and .detect
KMS hooks, when running cec_s_phys_addr_from_edid, can end up calling
CEC's .adap_enable hook. This introduces some reentrancy that isn't easy
to deal with properly.
The CEC hooks also don't share much state with the rest of the driver:
the registers are entirely separate, we don't share any variable, the
only thing that can conflict is the CEC clock divider setup that can be
affected by a mode set.
However, after discussing it, it looks like CEC should be able to
recover from this if it was to happen.
Fixes: bb7d785688 ("drm/vc4: Add HDMI audio support")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The vc4 HDMI driver has multiple path shared between the CEC, ALSA and
KMS frameworks, plus two interrupt handlers (CEC and hotplug) that will
read and modify a number of registers.
Even though not bug has been reported so far, it's definitely unsafe, so
let's just add a spinlock to protect the register access of the HDMI
controller.
Fixes: c8b75bca92 ("drm/vc4: Add KMS support for Raspberry Pi.")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Accessing the crtc->state pointer from outside the modesetting context
is not allowed. We thus need to copy whatever we need from the KMS state
to our structure in order to access it.
In VC4, a number of users of that pointers have crept in over the years,
and the previous commits removed them all but the HVS channel a CRTC has
been assigned.
Let's move this channel in struct vc4_crtc at atomic_begin() time, drop
it from our private state structure, and remove our use of crtc->state
from our vblank handler entirely.
Link: https://lore.kernel.org/all/YWgteNaNeaS9uWDe@phenom.ffwll.local/
Fixes: 87ebcd42fb ("drm/vc4: crtc: Assign output to channel automatically")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
In some situation, we can end up being stuck on a non-blocking that went
through properly.
The situation that seems to trigger it reliably is to first start a
non-blocking commit, and then right after, and before we had any vblank
interrupt), start a blocking commit.
This will lead to the first commit workqueue to be scheduled, setup the
display, while the second commit is waiting for the first one to be
completed.
The vblank interrupt will then be raised, vc4_crtc_handle_vblank() will
run and will compare the active dlist in the HVS channel to the one
associated with the crtc->state.
However, at that point, the second commit is waiting using
drm_atomic_helper_wait_for_dependencies that occurs after
drm_atomic_helper_swap_state has been called, so crtc->state points to
the second commit state. vc4_crtc_handle_vblank() will compare the two
dlist addresses and since they don't match will ignore the interrupt.
The vblank event will never be reported, and the first and second commit
will wait for the first commit completion until they timeout.
The underlying reason is that it was never safe to do so. Indeed,
accessing the ->state pointer access synchronization is based on
ownership guarantees that can only occur within the functions and hooks
defined as part of the KMS framework, and obviously the irq handler
isn't one of them. The rework to move to generic helpers only uncovered
the underlying issue.
However, since the code path between
drm_atomic_helper_wait_for_dependencies() and
drm_atomic_helper_wait_for_vblanks() is serialised and we can't get two
commits in that path at the same time, we can work around this issue by
setting a variable associated to struct drm_crtc to the dlist we expect,
and then using it from the vc4_crtc_handle_vblank() function.
Since that state is shared with the modesetting path, we also need to
introduce a spinlock to protect the code shared between the interrupt
handler and the modesetting path, protecting only our new variable for
now.
Link: https://lore.kernel.org/all/YWgteNaNeaS9uWDe@phenom.ffwll.local/
Fixes: 56d1fe0979 ("drm/vc4: Make pageflip completion handling more robust.")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Accessing the crtc->state pointer from outside the modesetting context
is not allowed. We thus need to copy whatever we need from the KMS state
to our structure in order to access it.
In VC4, a number of users of that pointers have crept in over the years,
the first one being whether or not the downstream controller of the
pixelvalve is our writeback controller.
Fortunately for us, Since commit 39fcb28083 ("drm/vc4: txp: Turn the
TXP into a CRTC of its own") this is no longer something that can change
from one commit to the other and is hardcoded.
Let's set this flag in struct vc4_crtc if we happen to be the TXP, and
drop the flag from our private state structure.
Link: https://lore.kernel.org/all/YWgteNaNeaS9uWDe@phenom.ffwll.local/
Fixes: 008095e065 ("drm/vc4: Add support for the transposer block")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
It is important to reinitialise the firmware array pointers to protect
against the case that the brcmfmac driver is reprobed without first
being unloaded.
The potential hazard was noticed while investigating
https://github.com/raspberrypi/firmware/issues/1644 .
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
drm_crtc_legacy_gamma_set updates the gamma_lut blob unconditionally,
which leads to unnecessary reprogramming of hardware.
Check whether the blob contents has actually changed before
signalling that it has been updated.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
commit 29c77550ee upstream.
When perf.data is not written cleanly, we would like to process existing
data as much as possible (please see f_header.data.size == 0 condition
in perf_session__read_header). However, perf.data with partial data may
crash perf. Specifically, we see crash in 'perf script' for NULL
session->header.env.arch.
Fix this by checking session->header.env.arch before using it to determine
native_arch. Also split the if condition so it is easier to read.
Committer notes:
If it is a pipe, we already assume is a native arch, so no need to check
session->header.env.arch.
Signed-off-by: Song Liu <songliubraving@fb.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: kernel-team@fb.com
Cc: stable@vger.kernel.org
Link: http://lore.kernel.org/lkml/20211004053238.514936-1-songliubraving@fb.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54c5639d8f upstream.
Nathan reported that because KASAN_SHADOW_OFFSET was not defined in
Kconfig, it prevents asan-stack from getting disabled with clang even
when CONFIG_KASAN_STACK is disabled: fix this by defining the
corresponding config.
Reported-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Alexandre Ghiti <alexandre.ghiti@canonical.com>
Fixes: 8ad8b72721 ("riscv: Add KASAN support")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9b57e9d501 ]
The idea behind kicked mask is that we should not re-kick a vcpu that
is already in the "kick" process, i.e. that was kicked and is
is about to be dispatched if certain conditions are met.
The problem with the current implementation is, that it assumes the
kicked vcpu is going to enter SIE shortly. But under certain
circumstances, the vcpu we just kicked will be deemed non-runnable and
will remain in wait state. This can happen, if the interrupt(s) this
vcpu got kicked to deal with got already cleared (because the interrupts
got delivered to another vcpu). In this case kvm_arch_vcpu_runnable()
would return false, and the vcpu would remain in kvm_vcpu_block(),
but this time with its kicked_mask bit set. So next time around we
wouldn't kick the vcpu form __airqs_kick_single_vcpu(), but would assume
that we just kicked it.
Let us make sure the kicked_mask is cleared before we give up on
re-dispatching the vcpu.
Fixes: 9f30f62163 ("KVM: s390: add gib_alert_irq_handler()")
Reported-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Michael Mueller <mimu@linux.ibm.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Link: https://lore.kernel.org/r/20211019175401.3757927-2-pasic@linux.ibm.com
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 462512824f ]
TX/RX descriptor ring fields are always little-endian, but conversion
wasn't performed for big-endian CPUs, so the driver failed to work.
This patch makes the driver work on big-endian CPUs. It was tested and
confirmed to work on NXP P1010 processor (PowerPC).
Signed-off-by: Alexey Denisov <rtgbnm@gmail.com>
Link: https://lore.kernel.org/r/20210128044859.280219-1-rtgbnm@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d02831e51 ]
sctp_sf_ootb() is called when processing DATA chunk in closed state,
and many other places are also using it.
The vtag in the chunk's sctphdr should be verified, otherwise, as
later in chunk length check, it may send abort with the existent
asoc's vtag, which can be exploited by one to cook a malicious
chunk to terminate a SCTP asoc.
When fails to verify the vtag from the chunk, this patch sets asoc
to NULL, so that the abort will be made with the vtag from the
received chunk later.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef16b1734f ]
sctp_sf_do_8_5_1_E_sa() is called when processing SHUTDOWN_ACK chunk
in cookie_wait and cookie_echoed state.
The vtag in the chunk's sctphdr should be verified, otherwise, as
later in chunk length check, it may send abort with the existent
asoc's vtag, which can be exploited by one to cook a malicious
chunk to terminate a SCTP asoc.
Note that when fails to verify the vtag from SHUTDOWN-ACK chunk,
SHUTDOWN COMPLETE message will still be sent back to peer, but
with the vtag from SHUTDOWN-ACK chunk, as said in 5) of
rfc4960#section-8.4.
While at it, also remove the unnecessary chunk length check from
sctp_sf_shut_8_4_5(), as it's already done in both places where
it calls sctp_sf_shut_8_4_5().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa0f697e45 ]
sctp_sf_violation() is called when processing HEARTBEAT_ACK chunk
in cookie_wait state, and some other places are also using it.
The vtag in the chunk's sctphdr should be verified, otherwise, as
later in chunk length check, it may send abort with the existent
asoc's vtag, which can be exploited by one to cook a malicious
chunk to terminate a SCTP asoc.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a64b341b86 ]
1. In closed state: in sctp_sf_do_5_1D_ce():
When asoc is NULL, making packet for abort will use chunk's vtag
in sctp_ootb_pkt_new(). But when asoc exists, vtag from the chunk
should be verified before using peer.i.init_tag to make packet
for abort in sctp_ootb_pkt_new(), and just discard it if vtag is
not correct.
2. In the other states: in sctp_sf_do_5_2_4_dupcook():
asoc always exists, but duplicate cookie_echo's vtag will be
handled by sctp_tietags_compare() and then take actions, so before
that we only verify the vtag for the abort sent for invalid chunk
length.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 438b95a7c9 ]
Currently INIT_ACK chunk in non-cookie_echoed state is processed in
sctp_sf_discard_chunk() to send an abort with the existent asoc's
vtag if the chunk length is not valid. But the vtag in the chunk's
sctphdr is not verified, which may be exploited by one to cook a
malicious chunk to terminal a SCTP asoc.
sctp_sf_discard_chunk() also is called in many other places to send
an abort, and most of those have this problem. This patch is to fix
it by sending abort with the existent asoc's vtag only if the vtag
from the chunk's sctphdr is verified in sctp_sf_discard_chunk().
Note on sctp_sf_do_9_1_abort() and sctp_sf_shutdown_pending_abort(),
the chunk length has been verified before sctp_sf_discard_chunk(),
so replace it with sctp_sf_discard(). On sctp_sf_do_asconf_ack() and
sctp_sf_do_asconf(), move the sctp_chunk_length_valid check ahead of
sctp_sf_discard_chunk(), then replace it with sctp_sf_discard().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f7019c7eb ]
Currently Linux SCTP uses the verification tag of the existing SCTP
asoc when failing to process and sending the packet with the ABORT
chunk. This will result in the peer accepting the ABORT chunk and
removing the SCTP asoc. One could exploit this to terminate a SCTP
asoc.
This patch is to fix it by always using the initiate tag of the
received INIT chunk for the ABORT chunk to be sent.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit af1a02aa23 upstream.
There is a race condition where the PHY state machine can change
members of the phydev structure at the same time userspace requests a
change via ethtool. To prevent this, have phy_ethtool_ksettings_set
take the PHY lock.
Fixes: 2d55173e71 ("phy: add generic function to support ksetting support")
Reported-by: Walter Stoll <Walter.Stoll@duagon.com>
Suggested-by: Walter Stoll <Walter.Stoll@duagon.com>
Tested-by: Walter Stoll <Walter.Stoll@duagon.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 707293a56f upstream.
Split phy_start_aneg into a wrapper which takes the PHY lock, and a
helper doing the real work. This will be needed when
phy_ethtook_ksettings_set takes the lock.
Fixes: 2d55173e71 ("phy: add generic function to support ksetting support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 64cd92d5e8 upstream.
This allows it to make use of a helper which assume the PHY is already
locked.
Fixes: 2d55173e71 ("phy: add generic function to support ksetting support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c10a485c3d upstream.
The PHY structure should be locked while copying information out if
it, otherwise there is no guarantee of self consistency. Without the
lock the PHY state machine could be updating the structure.
Fixes: 2d55173e71 ("phy: add generic function to support ksetting support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d9d6fd21a upstream.
sk->sk_err contains a positive number, yet async_wait.err wants the
opposite. Fix the missed sign flip, which Jakub caught by inspection.
Fixes: a42055e8d2 ("net/tls: Add support for async encryption of records for performance")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Daniel Jordan <daniel.m.jordan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ace19b9924 upstream.
A hard hang is observed whenever the ethernet interface is brought
down. If the PHY is stopped before the LPC core block is reset,
the SoC will hang. Comparing lpc_eth_close() and lpc_eth_open() I
re-arranged the ordering of the functions calls in lpc_eth_close() to
reset the hardware before stopping the PHY.
Fixes: b7370112f5 ("lpc32xx: Added ethernet driver")
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 759635760a upstream.
When the driver fails to allocate a new Rx buffer, it passes an empty Rx
descriptor (contains zero address and size) to the device and marks it
as invalid by setting the skb pointer in the descriptor's metadata to
NULL.
After processing enough Rx descriptors, the driver will try to process
the invalid descriptor, but will return immediately seeing that the skb
pointer is NULL. Since the driver no longer passes new Rx descriptors to
the device, the Rx queue will eventually become full and the device will
start to drop packets.
Fix this by recycling the received packet if allocation of the new
packet failed. This means that allocation is no longer performed at the
end of the Rx routine, but at the start, before tearing down the DMA
mapping of the received packet.
Remove the comment about the descriptor being zeroed as it is no longer
correct. This is OK because we either use the descriptor as-is (when
recycling) or overwrite its address and size fields with that of the
newly allocated Rx buffer.
The issue was discovered when a process ("perf") consumed too much
memory and put the system under memory pressure. It can be reproduced by
injecting slab allocation failures [1]. After the fix, the Rx queue no
longer comes to a halt.
[1]
# echo 10 > /sys/kernel/debug/failslab/times
# echo 1000 > /sys/kernel/debug/failslab/interval
# echo 100 > /sys/kernel/debug/failslab/probability
FAULT_INJECTION: forcing a failure.
name failslab, interval 1000, probability 100, space 0, times 8
[...]
Call Trace:
<IRQ>
dump_stack_lvl+0x34/0x44
should_fail.cold+0x32/0x37
should_failslab+0x5/0x10
kmem_cache_alloc_node+0x23/0x190
__alloc_skb+0x1f9/0x280
__netdev_alloc_skb+0x3a/0x150
mlxsw_pci_rdq_skb_alloc+0x24/0x90
mlxsw_pci_cq_tasklet+0x3dc/0x1200
tasklet_action_common.constprop.0+0x9f/0x100
__do_softirq+0xb5/0x252
irq_exit_rcu+0x7a/0xa0
common_interrupt+0x83/0xa0
</IRQ>
asm_common_interrupt+0x1e/0x40
RIP: 0010:cpuidle_enter_state+0xc8/0x340
[...]
mlxsw_spectrum2 0000:06:00.0: Failed to alloc skb for RDQ
Fixes: eda6500a98 ("mlxsw: Add PCI bus implementation")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/20211024064014.1060919-1-idosch@idosch.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a089e95b4 upstream.
nios2:allmodconfig builds fail with
make[1]: *** No rule to make target 'arch/nios2/boot/dts/""',
needed by 'arch/nios2/boot/dts/built-in.a'. Stop.
make: [Makefile:1868: arch/nios2/boot/dts] Error 2 (ignored)
This is seen with compile tests since those enable NIOS2_DTB_SOURCE_BOOL,
which in turn enables NIOS2_DTB_SOURCE. This causes the build error
because the default value for NIOS2_DTB_SOURCE is an empty string.
Disable NIOS2_DTB_SOURCE_BOOL for compile tests to avoid the error.
Fixes: 2fc8483fdc ("nios2: Build infrastructure")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c57eeecc5 upstream.
Drivers call netdev_set_num_tc() and then netdev_set_tc_queue()
to set the queue count and offset for each TC. So the queue count
and offset for the TCs may be zero for a short period after dev->num_tc
has been set. If a TX packet is being transmitted at this time in the
code path netdev_pick_tx() -> skb_tx_hash(), skb_tx_hash() may see
nonzero dev->num_tc but zero qcount for the TC. The while loop that
keeps looping while hash >= qcount will not end.
Fix it by checking the TC's qcount to be nonzero before using it.
Fixes: eadec877ce ("net: Add support for subordinate traffic classes to netdev_pick_tx")
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7a1e76d0f upstream.
Currently in net_ns_get_ownership() it may not be able to set uid or gid
if make_kuid or make_kgid returns an invalid value, and an uninit-value
issue can be triggered by this.
This patch is to fix it by initializing the uid and gid before calling
net_ns_get_ownership(), as it does in kobject_get_ownership()
Fixes: e6dee9f389 ("net-sysfs: add netdev_change_owner()")
Reported-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f68cd6348 upstream.
Syzbot reported ODEBUG warning in batadv_nc_mesh_free(). The problem was
in wrong error handling in batadv_mesh_init().
Before this patch batadv_mesh_init() was calling batadv_mesh_free() in case
of any batadv_*_init() calls failure. This approach may work well, when
there is some kind of indicator, which can tell which parts of batadv are
initialized; but there isn't any.
All written above lead to cleaning up uninitialized fields. Even if we hide
ODEBUG warning by initializing bat_priv->nc.work, syzbot was able to hit
GPF in batadv_nc_purge_paths(), because hash pointer in still NULL. [1]
To fix these bugs we can unwind batadv_*_init() calls one by one.
It is good approach for 2 reasons: 1) It fixes bugs on error handling
path 2) It improves the performance, since we won't call unneeded
batadv_*_free() functions.
So, this patch makes all batadv_*_init() clean up all allocated memory
before returning with an error to no call correspoing batadv_*_free()
and open-codes batadv_mesh_free() with proper order to avoid touching
uninitialized fields.
Link: https://lore.kernel.org/netdev/000000000000c87fbd05cef6bcb0@google.com/ [1]
Reported-and-tested-by: syzbot+28b0702ada0bf7381f58@syzkaller.appspotmail.com
Fixes: c6c8fea297 ("net: Add batman-adv meshing protocol")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Acked-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 55e6d80378 upstream.
In regcache_rbtree_insert_to_block(), when 'present' realloc failed,
the 'blk' which is supposed to assign to 'rbnode->block' will be freed,
so 'rbnode->block' points a freed memory, in the error handling path of
regcache_rbtree_init(), 'rbnode->block' will be freed again in
regcache_rbtree_exit(), KASAN will report double-free as follows:
BUG: KASAN: double-free or invalid-free in kfree+0xce/0x390
Call Trace:
slab_free_freelist_hook+0x10d/0x240
kfree+0xce/0x390
regcache_rbtree_exit+0x15d/0x1a0
regcache_rbtree_init+0x224/0x2c0
regcache_init+0x88d/0x1310
__regmap_init+0x3151/0x4a80
__devm_regmap_init+0x7d/0x100
madera_spi_probe+0x10f/0x333 [madera_spi]
spi_probe+0x183/0x210
really_probe+0x285/0xc30
To fix this, moving up the assignment of rbnode->block to immediately after
the reallocation has succeeded so that the data structure stays valid even
if the second reallocation fails.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 3f4ff561bc ("regmap: rbtree: Make cache_present bitmap per node")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20211012023735.1632786-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e77bcdd1f6 upstream.
Currently, we are using a fixed buffer size of length 2048 to display
rsrc_alloc output. As a result a maximum of 2048 characters of
rsrc_alloc output is displayed, which may lead sometimes to display only
partial output. This patch fixes this dependency on max limit of buffer
size and displays all PF VF entries.
Each column of the debugfs entry "rsrc_alloc" uses a fixed width of 12
characters to print the list of LFs of each block for a PF/VF. If the
length of list of LFs of a block exceeds this fixed width then the list
gets truncated and displays only a part of the list. This patch fixes
this by using the maximum possible length of list of LFs among all
blocks of all PFs and VFs entries as the width size.
Fixes: f788409714 ("octeontx2-af: Formatting debugfs entry rsrc_alloc.")
Fixes: 23205e6d06 ("octeontx2-af: Dump current resource provisioning status")
Signed-off-by: Rakesh Babu <rsaladi2@marvell.com>
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <Sunil.Goutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce7723e9cd upstream.
With commit db5ad6b7f8 ("nvme-tcp: try to send request in queue_rq
context") r2t and response PDU can get processed while send function
is executing.
Current data digest send code uses req->offset after kernel_sendmsg(),
this creates a race condition where req->offset gets reset before it
is used in send function.
This can happen in two cases -
1. Target sends r2t PDU which resets req->offset.
2. Target send response PDU which completes the req and then req is
used for a new command, nvme_tcp_setup_cmd_pdu() resets req->offset.
Fix this by storing req->offset in a local variable and using
this local variable after kernel_sendmsg().
Fixes: db5ad6b7f8 ("nvme-tcp: try to send request in queue_rq context")
Signed-off-by: Varun Prakash <varun@chelsio.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54713c85f5 upstream.
Lorenzo noticed that the code testing for program type compatibility of
tail call maps is potentially racy in that two threads could encounter a
map with an unset type simultaneously and both return true even though they
are inserting incompatible programs.
The race window is quite small, but artificially enlarging it by adding a
usleep_range() inside the check in bpf_prog_array_compatible() makes it
trivial to trigger from userspace with a program that does, essentially:
map_fd = bpf_create_map(BPF_MAP_TYPE_PROG_ARRAY, 4, 4, 2, 0);
pid = fork();
if (pid) {
key = 0;
value = xdp_fd;
} else {
key = 1;
value = tc_fd;
}
err = bpf_map_update_elem(map_fd, &key, &value, 0);
While the race window is small, it has potentially serious ramifications in
that triggering it would allow a BPF program to tail call to a program of a
different type. So let's get rid of it by protecting the update with a
spinlock. The commit in the Fixes tag is the last commit that touches the
code in question.
v2:
- Use a spinlock instead of an atomic variable and cmpxchg() (Alexei)
v3:
- Put lock and the members it protects into an embedded 'owner' struct (Daniel)
Fixes: 3324b584b6 ("ebpf: misc core cleanup")
Reported-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20211026110019.363464-1-toke@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd9733f5d7 upstream.
With two Msgs, msgA and msgB and a user doing nonblocking sendmsg calls (or
multiple cores) on a single socket 'sk' we could get the following flow.
msgA, sk msgB, sk
----------- ---------------
tcp_bpf_sendmsg()
lock(sk)
psock = sk->psock
tcp_bpf_sendmsg()
lock(sk) ... blocking
tcp_bpf_send_verdict
if (psock->eval == NONE)
psock->eval = sk_psock_msg_verdict
..
< handle SK_REDIRECT case >
release_sock(sk) < lock dropped so grab here >
ret = tcp_bpf_sendmsg_redir
psock = sk->psock
tcp_bpf_send_verdict
lock_sock(sk) ... blocking on B
if (psock->eval == NONE) <- boom.
psock->eval will have msgA state
The problem here is we dropped the lock on msgA and grabbed it with msgB.
Now we have old state in psock and importantly psock->eval has not been
cleared. So msgB will run whatever action was done on A and the verdict
program may never see it.
Fixes: 604326b41a ("bpf, sockmap: convert to generic sk_msg interface")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20211012052019.184398-1-liujian56@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04f8ef5643 upstream.
When enabling CONFIG_CGROUP_BPF, kmemleak can be observed by running
the command as below:
$mount -t cgroup -o none,name=foo cgroup cgroup/
$umount cgroup/
unreferenced object 0xc3585c40 (size 64):
comm "mount", pid 425, jiffies 4294959825 (age 31.990s)
hex dump (first 32 bytes):
01 00 00 80 84 8c 28 c0 00 00 00 00 00 00 00 00 ......(.........
00 00 00 00 00 00 00 00 6c 43 a0 c3 00 00 00 00 ........lC......
backtrace:
[<e95a2f9e>] cgroup_bpf_inherit+0x44/0x24c
[<1f03679c>] cgroup_setup_root+0x174/0x37c
[<ed4b0ac5>] cgroup1_get_tree+0x2c0/0x4a0
[<f85b12fd>] vfs_get_tree+0x24/0x108
[<f55aec5c>] path_mount+0x384/0x988
[<e2d5e9cd>] do_mount+0x64/0x9c
[<208c9cfe>] sys_mount+0xfc/0x1f4
[<06dd06e0>] ret_fast_syscall+0x0/0x48
[<a8308cb3>] 0xbeb4daa8
This is because that since the commit 2b0d3d3e4f ("percpu_ref: reduce
memory footprint of percpu_ref in fast path") root_cgrp->bpf.refcnt.data
is allocated by the function percpu_ref_init in cgroup_bpf_inherit which
is called by cgroup_setup_root when mounting, but not freed along with
root_cgrp when umounting. Adding cgroup_bpf_offline which calls
percpu_ref_kill to cgroup_kill_sb can free root_cgrp->bpf.refcnt.data in
umount path.
This patch also fixes the commit 4bfc0bb2c6 ("bpf: decouple the lifetime
of cgroup_bpf from cgroup itself"). A cgroup_bpf_offline is needed to do a
cleanup that frees the resources which are allocated by cgroup_bpf_inherit
in cgroup_setup_root.
And inside cgroup_bpf_offline, cgroup_get() is at the beginning and
cgroup_put is at the end of cgroup_bpf_release which is called by
cgroup_bpf_offline. So cgroup_bpf_offline can keep the balance of
cgroup's refcount.
Fixes: 2b0d3d3e4f ("percpu_ref: reduce memory footprint of percpu_ref in fast path")
Fixes: 4bfc0bb2c6 ("bpf: decouple the lifetime of cgroup_bpf from cgroup itself")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Roman Gushchin <guro@fb.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20211018075623.26884-1-quanyang.wang@windriver.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db6c3c064f upstream.
Add the missing endpoint max-packet sanity check to probe() to avoid
division by zero in lan78xx_tx_bh() in case a malicious device has
broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4f ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Cc: stable@vger.kernel.org # 4.3
Cc: Woojung.Huh@microchip.com <Woojung.Huh@microchip.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09b1d5dc6c upstream.
The management registrations locking was broken, the list was
locked for each wdev, but cfg80211_mgmt_registrations_update()
iterated it without holding all the correct spinlocks, causing
list corruption.
Rather than trying to fix it with fine-grained locking, just
move the lock to the wiphy/rdev (still need the list on each
wdev), we already need to hold the wdev lock to change it, so
there's no contention on the lock in any case. This trivially
fixes the bug since we hold one wdev's lock already, and now
will hold the lock that protects all lists.
Cc: stable@vger.kernel.org
Reported-by: Jouni Malinen <j@w1.fi>
Fixes: 6cd536fe62 ("cfg80211: change internal management frame registration API")
Link: https://lore.kernel.org/r/20211025133111.5cf733eab0f4.I7b0abb0494ab712f74e2efcd24bb31ac33f7eee9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 25e1f67eda upstream.
We should not access request members after the last send, even to
determine if indeed it was the last data payload send. The reason is
that a completion could have arrived and trigger a new execution of the
request which overridden these members. This was fixed by commit
825619b09a ("nvme-tcp: fix possible use-after-completion").
Commit e371af033c broke that assumption again to address cases where
multiple r2t pdus are sent per request. To fix it, we need to record the
request data_sent and data_len and after the payload network send we
reference these counters to determine weather we should advance the
request iterator.
Fixes: e371af033c ("nvme-tcp: fix incorrect h2cdata pdu offset accounting")
Reported-by: Keith Busch <kbusch@kernel.org>
Cc: stable@vger.kernel.org # 5.10+
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f1b228529 upstream.
Encountered a race between ocfs2_test_bg_bit_allocatable() and
jbd2_journal_put_journal_head() resulting in the below vmcore.
PID: 106879 TASK: ffff880244ba9c00 CPU: 2 COMMAND: "loop3"
Call trace:
panic
oops_end
no_context
__bad_area_nosemaphore
bad_area_nosemaphore
__do_page_fault
do_page_fault
page_fault
[exception RIP: ocfs2_block_group_find_clear_bits+316]
ocfs2_block_group_find_clear_bits [ocfs2]
ocfs2_cluster_group_search [ocfs2]
ocfs2_search_chain [ocfs2]
ocfs2_claim_suballoc_bits [ocfs2]
__ocfs2_claim_clusters [ocfs2]
ocfs2_claim_clusters [ocfs2]
ocfs2_local_alloc_slide_window [ocfs2]
ocfs2_reserve_local_alloc_bits [ocfs2]
ocfs2_reserve_clusters_with_limit [ocfs2]
ocfs2_reserve_clusters [ocfs2]
ocfs2_lock_refcount_allocators [ocfs2]
ocfs2_make_clusters_writable [ocfs2]
ocfs2_replace_cow [ocfs2]
ocfs2_refcount_cow [ocfs2]
ocfs2_file_write_iter [ocfs2]
lo_rw_aio
loop_queue_work
kthread_worker_fn
kthread
ret_from_fork
When ocfs2_test_bg_bit_allocatable() called bh2jh(bg_bh), the
bg_bh->b_private NULL as jbd2_journal_put_journal_head() raced and
released the jounal head from the buffer head. Needed to take bit lock
for the bit 'BH_JournalHead' to fix this race.
Link: https://lkml.kernel.org/r/1634820718-6043-1-git-send-email-gautham.ananthakrishna@oracle.com
Signed-off-by: Gautham Ananthakrishna <gautham.ananthakrishna@oracle.com>
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: <rajesh.sivaramasubramaniom@oracle.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9af372dc70 upstream.
To reset standard tuning circuit completely, after clear ESDHC_MIX_CTRL_EXE_TUNE,
also need to clear bit buffer_read_ready, this operation will finally clear the
USDHC IP internal logic flag execute_tuning_with_clr_buf, make sure the following
normal data transfer will not be impacted by standard tuning logic used before.
Find this issue when do quick SD card insert/remove stress test. During standard
tuning prodedure, if remove SD card, USDHC standard tuning logic can't clear the
internal flag execute_tuning_with_clr_buf. Next time when insert SD card, all
data related commands can't get any data related interrupts, include data transfer
complete interrupt, data timeout interrupt, data CRC interrupt, data end bit interrupt.
Always trigger software timeout issue. Even reset the USDHC through bits in register
SYS_CTRL (0x2C, bit28 reset tuning, bit26 reset data, bit 25 reset command, bit 24
reset all) can't recover this. From the user's point of view, USDHC stuck, SD can't
be recognized any more.
Fixes: d9370424c9 ("mmc: sdhci-esdhc-imx: reset tuning circuit when power on mmc card")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1634263236-6111-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92b18252b9 upstream.
While mmc0 enter suspend state, we need halt CQE to send legacy cmd(flush
cache) and disable cqe, for resume back, we enable CQE and not clear HALT
state.
In this case MediaTek mmc host controller will keep the value for HALT
state after CQE disable/enable flow, so the next CQE transfer after resume
will be timeout due to CQE is in HALT state, the log as below:
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: timeout for tag 2
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: ============ CQHCI REGISTER DUMP ===========
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Caps: 0x100020b6 | Version: 0x00000510
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Config: 0x00001103 | Control: 0x00000001
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Int stat: 0x00000000 | Int enab: 0x00000006
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Int sig: 0x00000006 | Int Coal: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: TDL base: 0xfd05f000 | TDL up32: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Doorbell: 0x8000203c | TCN: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Dev queue: 0x00000000 | Dev Pend: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Task clr: 0x00000000 | SSC1: 0x00001000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: SSC2: 0x00000001 | DCMD rsp: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: RED mask: 0xfdf9a080 | TERRI: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Resp idx: 0x00000000 | Resp arg: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: CRNQP: 0x00000000 | CRNQDUN: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: CRNQIS: 0x00000000 | CRNQIE: 0x00000000
This change check HALT state after CQE enable, if CQE is in HALT state, we
will clear it.
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Cc: stable@vger.kernel.org
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: a4080225f5 ("mmc: cqhci: support for command queue enabled host")
Link: https://lore.kernel.org/r/20211026070812.9359-1-wenbin.mei@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da353fac65 upstream.
sk->sk_err appears to expect a positive value, a convention that ktls
doesn't always follow and that leads to memory corruption in other code.
For instance,
[kworker]
tls_encrypt_done(..., err=<negative error from crypto request>)
tls_err_abort(.., err)
sk->sk_err = err;
[task]
splice_from_pipe_feed
...
tls_sw_do_sendpage
if (sk->sk_err) {
ret = -sk->sk_err; // ret is positive
splice_from_pipe_feed (continued)
ret = actor(...) // ret is still positive and interpreted as bytes
// written, resulting in underflow of buf->len and
// sd->len, leading to huge buf->offset and bogus
// addresses computed in later calls to actor()
Fix all tls_err_abort() callers to pass a negative error code
consistently and centralize the error-prone sign flip there, throwing in
a warning to catch future misuse and uninlining the function so it
really does only warn once.
Cc: stable@vger.kernel.org
Fixes: c46234ebb4 ("tls: RX path for ktls")
Reported-by: syzbot+b187b77c8474f9648fae@syzkaller.appspotmail.com
Signed-off-by: Daniel Jordan <daniel.m.jordan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2195f2062e upstream.
During probing, the driver tries to get a list (mask) of supported
command types in port100_get_command_type_mask() function. The value
is u64 and 0 is treated as invalid mask (no commands supported). The
function however returns also -ERRNO as u64 which will be interpret as
valid command mask.
Return 0 on every error case of port100_get_command_type_mask(), so the
probing will stop.
Cc: <stable@vger.kernel.org>
Fixes: 0347a6ab30 ("NFC: port100: Commands mechanism implementation")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fa40d9734a upstream.
The function tipc_crypto_key_rcv is used to parse MSG_CRYPTO messages
to receive keys from other nodes in the cluster in order to decrypt any
further messages from them.
This patch verifies that any supplied sizes in the message body are
valid for the received message.
Fixes: 1ef6f7c939 ("tipc: add automatic session key exchange")
Signed-off-by: Max VA <maxv@sentinelone.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a0023bb9dd upstream.
mv_init_host() propagates the value returned by mv_chip_id() which in turn
gets propagated by mv_pci_init_one() and hits local_pci_probe().
During the process of driver probing, the probe function should return < 0
for failure, otherwise, the kernel will treat value > 0 as success.
Since this is a bug rather than a recoverable runtime error we should
use dev_alert() instead of dev_err().
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e5a04be88 upstream.
Some systems such as the Microsoft Surface Laptop 4 leave interrupts
enabled and configured for use in sleep states on boot, which cause
unexpected behaviour such as spurious wakes and failed resumes in
s2idle states.
As interrupts should not be enabled until they are claimed and
explicitly enabled, disabling any interrupts mistakenly left enabled by
firmware should be safe.
Signed-off-by: Sachi King <nakato@nakato.io>
Link: https://lore.kernel.org/r/20211009033240.21543-1-nakato@nakato.io
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6dba4bdfd7 upstream.
This reverts commit a49d784d5a.
The updated binding was wrong / invalid and has been reverted. There
isn't any upstream kernel DTS using it and Broadcom isn't known to use
it neither. There is close to zero chance this will cause regression for
anyone.
Actually in-kernel bcm5301x.dtsi still uses the old good binding and so
it's broken since the driver update. This revert fixes it.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20211008205938.29925-3-zajec5@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 295cf15623 upstream.
Al reminds us that the usercopy API must only return complete failure
if absolutely nothing could be copied. Currently, if userspace does
something silly like giving us an unaligned pointer to Device memory,
or a size which overruns MTE tag bounds, we may fail to honour that
requirement when faulting on a multi-byte access even though a smaller
access could have succeeded.
Add a mitigation to the fixup routines to fall back to a single-byte
copy if we faulted on a larger access before anything has been written
to the destination, to guarantee making *some* forward progress. We
needn't be too concerned about the overall performance since this should
only occur when callers are doing something a bit dodgy in the first
place. Particularly broken userspace might still be able to trick
generic_perform_write() into an infinite loop by targeting write() at
an mmap() of some read-only device register where the fault-in load
succeeds but any store synchronously aborts such that copy_to_user() is
genuinely unable to make progress, but, well, don't do that...
CC: stable@vger.kernel.org
Reported-by: Chen Huang <chenhuang5@huawei.com>
Suggested-by: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/dc03d5c675731a1f24a62417dba5429ad744234e.1626098433.git.robin.murphy@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Chen Huang <chenhuang5@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 792bb6eb86 upstream.
[ 97.866748] a.out/2890 is trying to acquire lock:
[ 97.867829] ffff8881046763e8 (&ctx->uring_lock){+.+.}-{3:3}, at:
io_wq_submit_work+0x155/0x240
[ 97.869735]
[ 97.869735] but task is already holding lock:
[ 97.871033] ffff88810dfe0be8 (&ctx->uring_lock){+.+.}-{3:3}, at:
__x64_sys_io_uring_enter+0x3f0/0x5b0
[ 97.873074]
[ 97.873074] other info that might help us debug this:
[ 97.874520] Possible unsafe locking scenario:
[ 97.874520]
[ 97.875845] CPU0
[ 97.876440] ----
[ 97.877048] lock(&ctx->uring_lock);
[ 97.877961] lock(&ctx->uring_lock);
[ 97.878881]
[ 97.878881] *** DEADLOCK ***
[ 97.878881]
[ 97.880341] May be due to missing lock nesting notation
[ 97.880341]
[ 97.881952] 1 lock held by a.out/2890:
[ 97.882873] #0: ffff88810dfe0be8 (&ctx->uring_lock){+.+.}-{3:3}, at:
__x64_sys_io_uring_enter+0x3f0/0x5b0
[ 97.885108]
[ 97.885108] stack backtrace:
[ 97.890457] Call Trace:
[ 97.891121] dump_stack+0xac/0xe3
[ 97.891972] __lock_acquire+0xab6/0x13a0
[ 97.892940] lock_acquire+0x2c3/0x390
[ 97.894894] __mutex_lock+0xae/0x9f0
[ 97.901101] io_wq_submit_work+0x155/0x240
[ 97.902112] io_wq_cancel_cb+0x162/0x490
[ 97.904126] io_async_find_and_cancel+0x3b/0x140
[ 97.905247] io_issue_sqe+0x86d/0x13e0
[ 97.909122] __io_queue_sqe+0x10b/0x550
[ 97.913971] io_queue_sqe+0x235/0x470
[ 97.914894] io_submit_sqes+0xcce/0xf10
[ 97.917872] __x64_sys_io_uring_enter+0x3fb/0x5b0
[ 97.921424] do_syscall_64+0x2d/0x40
[ 97.922329] entry_SYSCALL_64_after_hwframe+0x44/0xa9
While holding uring_lock, e.g. from inline execution, async cancel
request may attempt cancellations through io_wq_submit_work, which may
try to grab a lock. Delay it to task_work, so we do it from a clean
context and don't have to worry about locking.
Cc: <stable@vger.kernel.org> # 5.5+
Fixes: c07e671951 ("io_uring: hold uring_lock while completing failed polled io in io_wq_submit_work()")
Reported-by: Abaci <abaci@linux.alibaba.com>
Reported-by: Hao Xu <haoxu@linux.alibaba.com>
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
[Lee: The first hunk solves a different (double free) issue in v5.10.
Only the first hunk of the original patch is relevant to v5.10 AND
the first hunk of the original patch is only relevant to v5.10]
Reported-by: syzbot+59d8a1f4e60c20c066cf@syzkaller.appspotmail.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 48ccc8edf5 upstream.
In randconfig builds, we sometimes come across this warning:
arm-linux-gnueabi-ld: XIP start address may cause MPU programming issues
While this is helpful for actual systems to figure out why it
fails, the warning does not provide any benefit for build testing,
so guard it in a check for CONFIG_COMPILE_TEST, which is usually
set on randconfig builds.
Fixes: 216218308c ("ARM: 8713/1: NOMMU: Support MPU in XIP configuration")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 44cc6412e6 upstream.
When frame pointers are used instead of the ARM unwinder,
and the kernel is built using clang with an external assembler
and CONFIG_XIP_KERNEL, every file produces two warnings
like:
arm-linux-gnueabi-ld: warning: orphan section `.ARM.extab' from `net/mac802154/util.o' being placed in section `.ARM.extab'
arm-linux-gnueabi-ld: warning: orphan section `.ARM.exidx' from `net/mac802154/util.o' being placed in section `.ARM.exidx'
The same fix was already merged for the normal (non-XIP)
linker script, with a longer description.
Fixes: c39866f268 ("arm/build: Always handle .ARM.exidx and .ARM.extab sections")
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eaf6cc7165 upstream.
Both the decompressor code and the kasan logic try to override
the memcpy() and memmove() definitions, which leading to a clash
in a KASAN-enabled kernel with XZ decompression:
arch/arm/boot/compressed/decompress.c:50:9: error: 'memmove' macro redefined [-Werror,-Wmacro-redefined]
#define memmove memmove
^
arch/arm/include/asm/string.h:59:9: note: previous definition is here
#define memmove(dst, src, len) __memmove(dst, src, len)
^
arch/arm/boot/compressed/decompress.c:51:9: error: 'memcpy' macro redefined [-Werror,-Wmacro-redefined]
#define memcpy memcpy
^
arch/arm/include/asm/string.h:58:9: note: previous definition is here
#define memcpy(dst, src, len) __memcpy(dst, src, len)
^
Here we want the set of functions from the decompressor, so undefine
the other macros before the override.
Link: https://lore.kernel.org/linux-arm-kernel/CACRpkdZYJogU_SN3H9oeVq=zJkRgRT1gDz3xp59gdqWXxw-B=w@mail.gmail.com/
Link: https://lore.kernel.org/lkml/202105091112.F5rmd4By-lkp@intel.com/
Fixes: d6d51a96c7 ("ARM: 9014/2: Replace string mem* functions for KASan")
Fixes: a7f464f3db ("ARM: 7001/2: Wire up support for the XZ decompressor")
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df909df077 upstream.
ARM: kasan: Fix __get_user_check failure with kasan
In macro __get_user_check defined in arch/arm/include/asm/uaccess.h,
error code is store in register int __e(r0). When kasan is
enabled, assigning value to kernel address might trigger kasan check,
which unexpectedly overwrites r0 and causes undefined behavior on arm
kasan images.
One example is failure in do_futex and results in process soft lockup.
Log:
watchdog: BUG: soft lockup - CPU#0 stuck for 62946ms! [rs:main
Q:Reg:1151]
...
(__asan_store4) from (futex_wait_setup+0xf8/0x2b4)
(futex_wait_setup) from (futex_wait+0x138/0x394)
(futex_wait) from (do_futex+0x164/0xe40)
(do_futex) from (sys_futex_time32+0x178/0x230)
(sys_futex_time32) from (ret_fast_syscall+0x0/0x50)
The soft lockup happens in function futex_wait_setup. The reason is
function get_futex_value_locked always return EINVAL, thus pc jump
back to retry label and causes looping.
This line in function get_futex_value_locked
ret = __get_user(*dest, from);
is expanded to
*dest = (typeof(*(p))) __r2; ,
in macro __get_user_check. Writing to pointer dest triggers kasan check
and overwrites the return value of __get_user_x function.
The assembly code of get_futex_value_locked in kernel/futex.c:
...
c01f6dc8: eb0b020e bl c04b7608 <__get_user_4>
// "x = (typeof(*(p))) __r2;" triggers kasan check and r0 is overwritten
c01f6dCc: e1a00007 mov r0, r7
c01f6dd0: e1a05002 mov r5, r2
c01f6dd4: eb04f1e6 bl c0333574 <__asan_store4>
c01f6dd8: e5875000 str r5, [r7]
// save ret value of __get_user(*dest, from), which is dest address now
c01f6ddc: e1a05000 mov r5, r0
...
// checking return value of __get_user failed
c01f6e00: e3550000 cmp r5, #0
...
c01f6e0c: 01a00005 moveq r0, r5
// assign return value to EINVAL
c01f6e10: 13e0000d mvnne r0, #13
Return value is the destination address of get_user thus certainly
non-zero, so get_futex_value_locked always return EINVAL.
Fix it by using a tmp vairable to store the error code before the
assignment. This fix has no effects to non-kasan images thanks to compiler
optimization. It only affects cases that overwrite r0 due to kasan check.
This should fix bug discussed in Link:
[1] https://lore.kernel.org/linux-arm-kernel/0ef7c2a5-5d8b-c5e0-63fa-31693fd4495c@gmail.com/
Fixes: 421015713b ("ARM: 9017/2: Enable KASan for ARM")
Signed-off-by: Lexi Shao <shaolexi@huawei.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the ability to load the names of alternative firmwares from the
Device Tree node. This permits separate firmwares for 43436s and 43438
and allows downstream firmwares to coexist with upstream.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
This reverts commit c52581ffa4.
Replace the hardcoded alternate firmware names with mappings provided
from Device Tree.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Add an option to enable configuration via the Media Controller API
(rather than the video-node-centric /dev/videoN) as about to
be used by libcamera as it enables more complex pipelines to be
handled.
Any source that has a libcamera tuning merged has MC enabled by
default.
Sources with no libcamera tuning merged have it disabled by
default.
In either case it can be overridden with the overlay parameter
"media-controller".
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
BCM43430/2 may be BCM43430B0 or BCM43436P, and BCM43430/1 can be either
BCM43430A1 or BCM43436S, the former being upstream names and the
latter downstream names for differently-sourced sister parts.
Make the choice of firmwares board-specific (without making the actual
firmwares board-specific) by placing the alternative firmware names for
each part in the DT node.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Add the ability to load the names of alternative firmwares from the
Device Tree node. This permits separate firmwares for 43436s and 43438
and allows downstream firmwares to coexist with upstream.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
This reverts commit c52581ffa4.
Replace the hardcoded alternate firmware names with mappings provided
from Device Tree.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
An unwanted side effect of enabling the BRCMDBG config setting is
redefining brcmf_info to be brcmf_err. This can be alarming to users
and makes it harder to spot real errors, so don't do it.
See: https://github.com/raspberrypi/linux/issues/4663
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Retain the old names for backwards compatibility for a while, while the
necessary firmware change rolls out.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Add predefined modelines for the 240p (NTSC) and 288p (PAL) progressive
modes, and report them through vc4_vec_connector_get_modes().
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Make vc4_vec_encoder_atomic_check() accept arbitrary modelines, as long
as they result in somewhat sane output from the VEC. The bounds have
been determined empirically. Additionally, add support for the
progressive 262-line and 312-line modes.
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
trigger_mode == 0 (default) => no effect / no registers written
trigger_mode == 1 => source
trigger_mode == 2 => sink
This can be set e.g. in /boot/cmdline.txt as imx477.trigger_mode=N
Signed-off-by: Jonas Jacob <jonas.jacob@neocortexvision.com>
commit aaac373317 upstream.
Replace the open coded calculations of the actual physical address
of the KVM stub vector table with a single adr_l invocation.
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
commit 3bcf906b19 upstream.
Replace the open coded arithmetic with a simple adr_l/sub pair. This
removes some open coded arithmetic involving virtual addresses, avoids
literal pools on v7+, and slightly reduces the footprint of the code.
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
commit d74d2b2250 upstream.
Replace the open coded PC relative offset calculations with adr_l and
ldr_l invocations. This removes some open coded PC relative arithmetic,
avoids literal pools on v7+, and slightly reduces the footprint of the
code. Note that ALT_SMP() expects a single instruction so move the macro
invocation after it.
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
commit 59d2f2827d upstream.
Now that calling __do_fixup_smp_on_up() can be done without passing
the physical-to-virtual offset in r3, we can replace the open coded
PC relative offset calculations with a pair of adr_l invocations. This
removes some open coded arithmetic involving virtual addresses, avoids
literal pools on v7+, and slightly reduces the footprint of the code.
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
commit 450abd38fe upstream.
Currently, the .alt.smp.init section contains the virtual addresses
of the patch sites. Since patching may occur both before and after
switching into virtual mode, this requires some manual handling of
the address when applying the UP alternative.
Let's simplify this by using relative offsets in the table entries:
this allows us to simply add each entry's address to its contents,
regardless of whether we are running in virtual mode or not.
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
commit 91580f0dbf upstream.
Replace the open coded PC relative offset calculations with adr_l
and ldr_l invocations. This removes some open coded arithmetic
involving virtual addresses, avoids literal pools on v7+, and slightly
reduces the footprint of the code.
Note that it also removes a stale comment about the contents of r6.
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
commit 172c34c9ff upstream.
Replace the open coded PC relative offset calculations involving
__turn_mmu_on and __turn_mmu_on_end with a pair of adr_l invocations.
This removes some open coded arithmetic involving virtual addresses,
avoids literal pools on v7+, and slightly reduces the footprint of the
code.
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
commit 62c4a2e202 upstream.
Replace the open coded PC relative offset calculations with a pair of
adr_l invocations. This removes some open coded arithmetic involving
virtual addresses, avoids literal pools on v7+, and slightly reduces
the footprint of the code.
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
commit 9443076e43 upstream.
The ARM kernel's linear map starts at PAGE_OFFSET, which maps to a
physical address (PHYS_OFFSET) that is platform specific, and is
discovered at boot. Since we don't want to slow down translations
between physical and virtual addresses by keeping the offset in a
variable in memory, we implement this by patching the code performing
the translation, and putting the offset between PAGE_OFFSET and the
start of physical RAM directly into the instruction opcodes.
As we only patch up to 8 bits of offset, yielding 4 GiB >> 8 == 16 MiB
of granularity, we have to round up PHYS_OFFSET to the next multiple if
the start of physical RAM is not a multiple of 16 MiB. This wastes some
physical RAM, since the memory that was skipped will now live below
PAGE_OFFSET, making it inaccessible to the kernel.
We can improve this by changing the patchable sequences and the patching
logic to carry more bits of offset: 11 bits gives us 4 GiB >> 11 == 2 MiB
of granularity, and so we will never waste more than that amount by
rounding up the physical start of DRAM to the next multiple of 2 MiB.
(Note that 2 MiB granularity guarantees that the linear mapping can be
created efficiently, whereas less than 2 MiB may result in the linear
mapping needing another level of page tables)
This helps Zhen Lei's scenario, where the start of DRAM is known to be
occupied. It also helps EFI boot, which relies on the firmware's page
allocator to allocate space for the decompressed kernel as low as
possible. And if the KASLR patches ever land for 32-bit, it will give
us 3 more bits of randomization of the placement of the kernel inside
the linear region.
For the ARM code path, it simply comes down to using two add/sub
instructions instead of one for the carryless version, and patching
each of them with the correct immediate depending on the rotation
field. For the LPAE calculation, which has to deal with a carry, it
patches the MOVW instruction with up to 12 bits of offset (but we only
need 11 bits anyway)
For the Thumb2 code path, patching more than 11 bits of displacement
would be somewhat cumbersome, but the 11 bits we need fit nicely into
the second word of the u16[2] opcode, so we simply update the immediate
assignment and the left shift to create an addend of the right magnitude.
Suggested-by: Zhen Lei <thunder.leizhen@huawei.com>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
commit e8e00f5afb upstream.
In preparation for reducing the phys-to-virt minimum relative alignment
from 16 MiB to 2 MiB, switch to patchable sequences involving MOVW
instructions that can more easily be manipulated to carry a 12-bit
immediate. Note that the non-LPAE ARM sequence is not updated: MOVW
may not be supported on non-LPAE platforms, and the sequence itself
can be updated more easily to apply the 12 bits of displacement.
For Thumb2, which has many more versions of opcodes, switch to a sequence
that can be patched by the same patching code for both versions. Note
that the Thumb2 opcodes for MOVW and MVN are unambiguous, and have no
rotation bits in their immediate fields, so there is no need to use
placeholder constants in the asm blocks.
While at it, drop the 'volatile' qualifiers from the asm blocks: the
code does not have any side effects that are invisible to the compiler,
so it is free to omit these sequences if the outputs are not used.
Suggested-by: Russell King <linux@armlinux.org.uk>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
commit 0e3db6c9d7 upstream.
Declutter the code in __fixup_pv_table() by using the new adr_l/str_l
macros to take PC relative references to external symbols, and by
using the value of PHYS_OFFSET passed in r8 to calculate the p2v
offset.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
commit 2730e8eaa4 upstream.
Free up a register in the p2v patching code by switching to relative
references, which don't require keeping the phys-to-virt displacement
live in a register.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
commit 7a94849e81 upstream.
The big and little endian versions of the ARM p2v patching routine only
differ in the values of the constants, so factor those out into macros
so that we only have one version of the logic sequence to maintain.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
commit 4b16421c3e upstream.
The ARM and Thumb2 versions of the p2v patching loop have some overlap
at the end of the loop, so factor that out. As numeric labels are not
required to be unique, and may therefore be ambiguous, use named local
labels for the start and end of the loop instead.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
commit eae78e1a97 upstream.
Move the phys2virt patching code into a separate .S file before doing
some work on it.
Suggested-by: Nicolas Pitre <nico@fluxnic.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
commit 22f2d23098 upstream.
When using the new adr_l/ldr_l/str_l macros to refer to external symbols
from modules, the linker may emit place relative ELF relocations that
need to be fixed up by the module loader. So add support for these.
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
The HVS Gamma block can only be updated when idle, so we need to disable
the HVS channel when the gamma property is set in an atomic commit.
Since the pixelvalve cannot have its assigned channel halted without
stalling unless it's disabled as well, in our case that means forcing a
full disable / enable cycle on the pipeline.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
BCM2711 changes from a 256 entry lookup table to a 16 point
piecewise linear function as the pipeline bitdepth has increased
to make a LUT unwieldy.
Implement a simple conversion from a 256 entry LUT that userspace
is likely to expect to 16 evenly spread points in the PWL. This
could be improved with curve fitting at a later date.
Co-developed-by: Juerg Haefliger <juergh@canonical.com>
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
clk-2835 is deprecated and gets an innacurate clock for VEC (107MHz).
Switch to clk-raspberrypi which uses the right PLL to get an accurate 108MHz.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
commit 9d417cbe36 upstream.
tglx notes:
This function [futex_detect_cmpxchg] is only needed when an
architecture has to runtime discover whether the CPU supports it or
not. ARM has unconditional support for this, so the obvious thing to
do is the below.
Fixes linkage failure from Clang randconfigs:
kernel/futex.o:(.text.fixup+0x5c): relocation truncated to fit: R_ARM_JUMP24 against `.init.text'
and boot failures for CONFIG_THUMB2_KERNEL.
Link: https://github.com/ClangBuiltLinux/linux/issues/325
Comments from Nick Desaulniers:
See-also: 03b8c7b623 ("futex: Allow architectures to skip
futex_atomic_cmpxchg_inatomic() test")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Nathan Chancellor <nathan@kernel.org>
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org # v3.14+
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 183d9ebd44 ("selftests/bpf: Fix core_reloc test runner") causes
builds of selftests/bpf to fail on 5.10.y since the branch doesn't have the
ASSERT_FALSE macro yet. Replace ASSERT_FALSE with ASSERT_EQ.
Fixes: 183d9ebd44 ("selftests/bpf: Fix core_reloc test runner")
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed65df63a3 upstream.
While writing an email explaining the "bit = 0" logic for a discussion on
making ftrace_test_recursion_trylock() disable preemption, I discovered a
path that makes the "not do the logic if bit is zero" unsafe.
The recursion logic is done in hot paths like the function tracer. Thus,
any code executed causes noticeable overhead. Thus, tricks are done to try
to limit the amount of code executed. This included the recursion testing
logic.
Having recursion testing is important, as there are many paths that can
end up in an infinite recursion cycle when tracing every function in the
kernel. Thus protection is needed to prevent that from happening.
Because it is OK to recurse due to different running context levels (e.g.
an interrupt preempts a trace, and then a trace occurs in the interrupt
handler), a set of bits are used to know which context one is in (normal,
softirq, irq and NMI). If a recursion occurs in the same level, it is
prevented*.
Then there are infrastructure levels of recursion as well. When more than
one callback is attached to the same function to trace, it calls a loop
function to iterate over all the callbacks. Both the callbacks and the
loop function have recursion protection. The callbacks use the
"ftrace_test_recursion_trylock()" which has a "function" set of context
bits to test, and the loop function calls the internal
trace_test_and_set_recursion() directly, with an "internal" set of bits.
If an architecture does not implement all the features supported by ftrace
then the callbacks are never called directly, and the loop function is
called instead, which will implement the features of ftrace.
Since both the loop function and the callbacks do recursion protection, it
was seemed unnecessary to do it in both locations. Thus, a trick was made
to have the internal set of recursion bits at a more significant bit
location than the function bits. Then, if any of the higher bits were set,
the logic of the function bits could be skipped, as any new recursion
would first have to go through the loop function.
This is true for architectures that do not support all the ftrace
features, because all functions being traced must first go through the
loop function before going to the callbacks. But this is not true for
architectures that support all the ftrace features. That's because the
loop function could be called due to two callbacks attached to the same
function, but then a recursion function inside the callback could be
called that does not share any other callback, and it will be called
directly.
i.e.
traced_function_1: [ more than one callback tracing it ]
call loop_func
loop_func:
trace_recursion set internal bit
call callback
callback:
trace_recursion [ skipped because internal bit is set, return 0 ]
call traced_function_2
traced_function_2: [ only traced by above callback ]
call callback
callback:
trace_recursion [ skipped because internal bit is set, return 0 ]
call traced_function_2
[ wash, rinse, repeat, BOOM! out of shampoo! ]
Thus, the "bit == 0 skip" trick is not safe, unless the loop function is
call for all functions.
Since we want to encourage architectures to implement all ftrace features,
having them slow down due to this extra logic may encourage the
maintainers to update to the latest ftrace features. And because this
logic is only safe for them, remove it completely.
[*] There is on layer of recursion that is allowed, and that is to allow
for the transition between interrupt context (normal -> softirq ->
irq -> NMI), because a trace may occur before the context update is
visible to the trace recursion logic.
Link: https://lore.kernel.org/all/609b565a-ed6e-a1da-f025-166691b5d994@linux.alibaba.com/
Link: https://lkml.kernel.org/r/20211018154412.09fcad3c@gandalf.local.home
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <James.Bottomley@hansenpartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Miroslav Benes <mbenes@suse.cz>
Cc: Joe Lawrence <joe.lawrence@redhat.com>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: "Peter Zijlstra (Intel)" <peterz@infradead.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Jisheng Zhang <jszhang@kernel.org>
Cc: =?utf-8?b?546L6LSH?= <yun.wang@linux.alibaba.com>
Cc: Guo Ren <guoren@kernel.org>
Cc: stable@vger.kernel.org
Fixes: edc15cafcb ("tracing: Avoid unnecessary multiple recursion checks")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a46044a92a upstream.
Since commit 2a671f77ee ("s390/pci: fix use after free of zpci_dev")
the reference count of a zpci_dev is incremented between
pcibios_add_device() and pcibios_release_device() which was supposed to
prevent the zpci_dev from being freed while the common PCI code has
access to it. It was missed however that the handling of zPCI
availability events assumed that once zpci_zdev_put() was called no
later availability event would still see the device. With the previously
mentioned commit however this assumption no longer holds and we must
make sure that we only drop the initial long-lived reference the zPCI
subsystem holds exactly once.
Do so by introducing a zpci_device_reserved() function that handles when
a device is reserved. Here we make sure the zpci_dev will not be
considered for further events by removing it from the zpci_list.
This also means that the device actually stays in the
ZPCI_FN_STATE_RESERVED state between the time we know it has been
reserved and the final reference going away. We thus need to consider it
a real state instead of just a conceptual state after the removal. The
final cleanup of PCI resources, removal from zbus, and destruction of
the IOMMU stays in zpci_release_device() to make sure holders of the
reference do see valid data until the release.
Fixes: 2a671f77ee ("s390/pci: fix use after free of zpci_dev")
Cc: stable@vger.kernel.org
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 43a08c3bda upstream.
When isotp_sendmsg() concurrent, tx.state of all TX processes can be
ISOTP_IDLE. The conditions so->tx.state != ISOTP_IDLE and
wq_has_sleeper(&so->wait) can not protect TX buffer from being
accessed by multiple TX processes.
We can use cmpxchg() to try to modify tx.state to ISOTP_SENDING firstly.
If the modification of the previous process succeed, the later process
must wait tx.state to ISOTP_IDLE firstly. Thus, we can ensure TX buffer
is accessed by only one process at the same time. And we should also
restore the original tx.state at the subsequent error processes.
Fixes: e057dd3fc2 ("can: add ISO 15765-2:2016 transport protocol")
Link: https://lore.kernel.org/all/c2517874fbdf4188585cf9ddf67a8fa74d5dbde5.1633764159.git.william.xuanziyang@huawei.com
Cc: stable@vger.kernel.org
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9f9f0f1999 ]
rx unused desc is the desc that need attatching new buffer
before refilling to hw to receive new packet, the number of
desc need attatching new buffer is calculated using next_to_use
and next_to_clean. when next_to_use == next_to_clean, currently
hns3 driver assumes that all the desc has the buffer attatched,
but 'next_to_use == next_to_clean' also means all the desc need
attatching new buffer if hw has comsumed all the desc and the
driver has not attatched any buffer to the desc yet.
This patch adds 'refill' in desc_cb to indicate whether a new
buffer has been refilled to a desc.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63acd42c0d ]
Commit f1a0a376ca ("sched/core: Initialize the idle task with
preemption disabled") removed the init_idle() call from
idle_thread_get(). This was the sole call-path on hotplug that resets
the Shadow Call Stack (scs) Stack Pointer (sp).
Not resetting the scs-sp leads to scs overflow after enough hotplug
cycles. Therefore add an explicit scs_task_reset() to the hotplug code
to make sure the scs-sp does get reset on hotplug.
Fixes: f1a0a376ca ("sched/core: Initialize the idle task with preemption disabled")
Signed-off-by: Woody Lin <woodylin@google.com>
[peterz: Changelog]
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Link: https://lore.kernel.org/r/20211012083521.973587-1-woodylin@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7fb223d0ad ]
Commit 8c0eb596ba ("[SCSI] qla2xxx: Fix a memory leak in an error path of
qla2x00_process_els()"), intended to change:
bsg_job->request->msgcode == FC_BSG_HST_ELS_NOLOGIN
to:
bsg_job->request->msgcode != FC_BSG_RPT_ELS
but changed it to:
bsg_job->request->msgcode == FC_BSG_RPT_ELS
instead.
Change the == to a != to avoid leaking the fcport structure or freeing
unallocated memory.
Link: https://lore.kernel.org/r/20211012191834.90306-2-jgu@purestorage.com
Fixes: 8c0eb596ba ("[SCSI] qla2xxx: Fix a memory leak in an error path of qla2x00_process_els()")
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Joy Gu <jgu@purestorage.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 187a580c9e ]
In commit 9e67600ed6 ("scsi: iscsi: Fix race condition between login and
sync thread") we meant to add a check where before we call ->set_param() we
make sure the iscsi_cls_connection is bound. The problem is that between
versions 4 and 5 of the patch the deletion of the unchecked set_param()
call was dropped so we ended up with 2 calls. As a result we can still hit
a crash where we access the unbound connection on the first call.
This patch removes that first call.
Fixes: 9e67600ed6 ("scsi: iscsi: Fix race condition between login and sync thread")
Link: https://lore.kernel.org/r/20211010161904.60471-1-michael.christie@oracle.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Li Feng <fengli@smartx.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d997cc1715 ]
On i.MX7S and i.MX8M* (but not i.MX6*) the pwrkey device has an
associated clock. Accessing the registers requires that this clock is
enabled. Binding the driver on at least i.MX7S and i.MX8MP while not
having the clock enabled results in a complete hang of the machine.
(This usually only happens if snvs_pwrkey is built as a module and the
rtc-snvs driver isn't already bound because at bootup the required clk
is on and only gets disabled when the clk framework disables unused clks
late during boot.)
This completes the fix in commit 135be16d35 ("ARM: dts: imx7s: add
snvs clock to pwrkey").
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211013062848.2667192-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ff6d64e68 ]
The `cpu` argument of perf_evsel__read() must specify the cpu index.
perf_cpu_map__for_each_cpu() is for iterating the cpu number (not index)
and is thus not appropriate for use with perf_evsel__read().
So, if there is an offline CPU, the cpu number specified in the argument
may point out of range because the cpu number and the cpu index are
different.
Fix test_stat_cpu().
Testing it:
# make tests -C tools/lib/perf/
make: Entering directory '/home/nakamura/kernel_src/linux-5.15-rc4_fix/tools/lib/perf'
running static:
- running tests/test-cpumap.c...OK
- running tests/test-threadmap.c...OK
- running tests/test-evlist.c...OK
- running tests/test-evsel.c...OK
running dynamic:
- running tests/test-cpumap.c...OK
- running tests/test-threadmap.c...OK
- running tests/test-evlist.c...OK
- running tests/test-evsel.c...OK
make: Leaving directory '/home/nakamura/kernel_src/linux-5.15-rc4_fix/tools/lib/perf'
Signed-off-by: Shunsuke Nakamura <nakamura.shun@fujitsu.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20211011083704.4108720-1-nakamura.shun@fujitsu.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b37a15188e ]
The snd_hdac_bus_reset_link() contains logic to clear STATESTS register
before performing controller reset. This code dates back to an old
bugfix in commit e8a7f136f5 ("[ALSA] hda-intel - Improve HD-audio
codec probing robustness"). Originally the code was added to
azx_reset().
The code was moved around in commit a41d122449 ("ALSA: hda - Embed bus
into controller object") and ended up to snd_hdac_bus_reset_link() and
called primarily via snd_hdac_bus_init_chip().
The logic to clear STATESTS is correct when snd_hdac_bus_init_chip() is
called when controller is not in reset. In this case, STATESTS can be
cleared. This can be useful e.g. when forcing a controller reset to retry
codec probe. A normal non-power-on reset will not clear the bits.
However, this old logic is problematic when controller is already in
reset. The HDA specification states that controller must be taken out of
reset before writing to registers other than GCTL.CRST (1.0a spec,
3.3.7). The write to STATESTS in snd_hdac_bus_reset_link() will be lost
if the controller is already in reset per the HDA specification mentioned.
This has been harmless on older hardware. On newer generation of Intel
PCIe based HDA controllers, if configured to report issues, this write
will emit an unsupported request error. If ACPI Platform Error Interface
(APEI) is enabled in kernel, this will end up to kernel log.
Fix the code in snd_hdac_bus_reset_link() to only clear the STATESTS if
the function is called when controller is not in reset. Otherwise
clearing the bits is not possible and should be skipped.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211012142935.3731820-1-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6636fec29c ]
On SPEAr3xx, ethernet driver is not compatible with the SPEAr600
one.
Indeed, SPEAr3xx uses an earlier version of this IP (v3.40) and
needs some driver tuning compare to SPEAr600.
The v3.40 IP support was added to stmmac driver and this patch
fixes this issue and use the correct compatible string for
SPEAr3xx
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77a5b9e3d1 ]
Currently inode_in_dir() ignores errors returned from
btrfs_lookup_dir_index_item() and from btrfs_lookup_dir_item(), treating
any errors as if the directory entry does not exists in the fs/subvolume
tree, which is obviously not correct, as we can get errors such as -EIO
when reading extent buffers while searching the fs/subvolume's tree.
Fix that by making inode_in_dir() return the errors and making its only
caller, add_inode_ref(), deal with returned errors as well.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0f1886de7 ]
It seems that a few recent AMD systems show the codec configuration
errors at the early boot, while loading the driver at a later stage
works magically. Although the root cause of the error isn't clear,
it's certainly not bad to allow retrying the codec probe in such a
case if that helps.
This patch adds the capability for retrying the probe upon codec probe
errors on the certain AMD platforms. The probe_work is changed to a
delayed work, and at the secondary call, it'll jump to the codec
probing.
Note that, not only adding the re-probing, this includes the behavior
changes in the codec configuration function. Namely,
snd_hda_codec_configure() won't unregister the codec at errors any
longer. Instead, its caller, azx_codec_configure() unregisters the
codecs with the probe failures *if* any codec has been successfully
configured. If all codec probe failed, it doesn't unregister but let
it re-probed -- which is the most case we're seeing and this patch
tries to improve.
Even if the driver doesn't re-probe or give up, it will go to the
"free-all" error path, hence the leftover codecs shall be disabled /
deleted in anyway.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1190801
Link: https://lore.kernel.org/r/20211006141940.2897-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit adfb7b4966 upstream.
Currently the max tx size supported by the hw is calculated by
using the max BD num supported by the hw. According to the hw
user manual, the max tx size is fixed value for both non-TSO and
TSO skb.
This patch updates the max tx size according to the manual.
Fixes: 8ae10cfb5089("net: hns3: support tx-scatter-gather-fraglist feature")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fac3cb82a5 upstream.
When I added IGMPv3 support I decided to follow the RFC for computing
the GMI dynamically:
" 8.4. Group Membership Interval
The Group Membership Interval is the amount of time that must pass
before a multicast router decides there are no more members of a
group or a particular source on a network.
This value MUST be ((the Robustness Variable) times (the Query
Interval)) plus (one Query Response Interval)."
But that actually is inconsistent with how the bridge used to compute it
for IGMPv2, where it was user-configurable that has a correct default value
but it is up to user-space to maintain it. This would make it consistent
with the other timer values which are also maintained correct by the user
instead of being dynamically computed. It also changes back to the previous
user-expected GMI behaviour for IGMPv3 queries which were supported before
IGMPv3 was added. Note that to properly compute it dynamically we would
need to add support for "Robustness Variable" which is currently missing.
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Fixes: 0436862e41 ("net: bridge: mcast: support for IGMPv3/MLDv2 ALLOW_NEW_SOURCES report")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b1499a817 upstream.
The nci_core_conn_close_rsp_packet() function will release the conn_info
with given conn_id. However, it needs to set the rf_conn_info to NULL to
prevent other routines like nci_rf_intf_activated_ntf_packet() to trigger
the UAF.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a25dfa67f upstream.
Since commit c300ab9f08 ("KVM: x86: Replace late check_nested_events() hack with
more precise fix") there is no longer the certainty that check_nested_events()
tries to inject an external interrupt vmexit to L1 on every call to vcpu_enter_guest.
Therefore, even in that case we need to set KVM_REQ_EVENT. This ensures
that inject_pending_event() is called, and from there kvm_check_nested_events().
Fixes: c300ab9f08 ("KVM: x86: Replace late check_nested_events() hack with more precise fix")
Cc: stable@vger.kernel.org
Reviewed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 496c5fe25c upstream.
In isa206_idle_insn_mayloss() we store various registers into the stack
red zone, which is allowed.
However inside the IDLE_STATE_ENTER_SEQ_NORET macro we save r2 again,
to 0(r1), which corrupts the stack back chain.
We used to do the same in isa206_idle_insn_mayloss() itself, but we
fixed that in 73287caa92 ("powerpc64/idle: Fix SP offsets when saving
GPRs"), however we missed that the macro also corrupts the back chain.
Corrupting the back chain is bad for debuggability but doesn't
necessarily cause a bug.
However we recently changed the stack handling in some KVM code, and it
now relies on the stack back chain being valid when it returns. The
corruption causes that code to return with r1 pointing somewhere in
kernel data, at some point LR is restored from the stack and we branch
to NULL or somewhere else invalid.
Only affects Power8 hosts running KVM guests, with dynamic_mt_modes
enabled (which it is by default).
The fixes tag below points to the commit that changed the KVM stack
handling, exposing this bug. The actual corruption of the back chain has
always existed since 948cf67c47 ("powerpc: Add NAP mode support on
Power7 in HV mode").
Fixes: 9b4416c509 ("KVM: PPC: Book3S HV: Fix stack handling in idle_kvm_start_guest()")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211020094826.3222052-1-mpe@ellerman.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cdeb5d7d89 upstream.
We call idle_kvm_start_guest() from power7_offline() if the thread has
been requested to enter KVM. We pass it the SRR1 value that was returned
from power7_idle_insn() which tells us what sort of wakeup we're
processing.
Depending on the SRR1 value we pass in, the KVM code might enter the
guest, or it might return to us to do some host action if the wakeup
requires it.
If idle_kvm_start_guest() is able to handle the wakeup, and enter the
guest it is supposed to indicate that by returning a zero SRR1 value to
us.
That was the behaviour prior to commit 10d91611f4 ("powerpc/64s:
Reimplement book3s idle code in C"), however in that commit the
handling of SRR1 was reworked, and the zeroing behaviour was lost.
Returning from idle_kvm_start_guest() without zeroing the SRR1 value can
confuse the host offline code, causing the guest to crash and other
weirdness.
Fixes: 10d91611f4 ("powerpc/64s: Reimplement book3s idle code in C")
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211015133929.832061-2-mpe@ellerman.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b4416c509 upstream.
In commit 10d91611f4 ("powerpc/64s: Reimplement book3s idle code in
C") kvm_start_guest() became idle_kvm_start_guest(). The old code
allocated a stack frame on the emergency stack, but didn't use the
frame to store anything, and also didn't store anything in its caller's
frame.
idle_kvm_start_guest() on the other hand is written more like a normal C
function, it creates a frame on entry, and also stores CR/LR into its
callers frame (per the ABI). The problem is that there is no caller
frame on the emergency stack.
The emergency stack for a given CPU is allocated with:
paca_ptrs[i]->emergency_sp = alloc_stack(limit, i) + THREAD_SIZE;
So emergency_sp actually points to the first address above the emergency
stack allocation for a given CPU, we must not store above it without
first decrementing it to create a frame. This is different to the
regular kernel stack, paca->kstack, which is initialised to point at an
initial frame that is ready to use.
idle_kvm_start_guest() stores the backchain, CR and LR all of which
write outside the allocation for the emergency stack. It then creates a
stack frame and saves the non-volatile registers. Unfortunately the
frame it creates is not large enough to fit the non-volatiles, and so
the saving of the non-volatile registers also writes outside the
emergency stack allocation.
The end result is that we corrupt whatever is at 0-24 bytes, and 112-248
bytes above the emergency stack allocation.
In practice this has gone unnoticed because the memory immediately above
the emergency stack happens to be used for other stack allocations,
either another CPUs mc_emergency_sp or an IRQ stack. See the order of
calls to irqstack_early_init() and emergency_stack_init().
The low addresses of another stack are the top of that stack, and so are
only used if that stack is under extreme pressue, which essentially
never happens in practice - and if it did there's a high likelyhood we'd
crash due to that stack overflowing.
Still, we shouldn't be corrupting someone else's stack, and it is purely
luck that we aren't corrupting something else.
To fix it we save CR/LR into the caller's frame using the existing r1 on
entry, we then create a SWITCH_FRAME_SIZE frame (which has space for
pt_regs) on the emergency stack with the backchain pointing to the
existing stack, and then finally we switch to the new frame on the
emergency stack.
Fixes: 10d91611f4 ("powerpc/64s: Reimplement book3s idle code in C")
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211015133929.832061-1-mpe@ellerman.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 73287caa92 upstream.
The idle entry/exit code saves/restores GPRs in the stack "red zone"
(Protected Zone according to PowerPC64 ELF ABI v2). However, the offset
used for the first GPR is incorrect and overwrites the back chain - the
Protected Zone actually starts below the current SP. In practice this is
probably not an issue, but it's still incorrect so fix it.
Also expand the comments to explain why using the stack "red zone"
instead of creating a new stackframe is appropriate here.
Signed-off-by: Christopher M. Riedl <cmr@codefail.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210206072342.5067-1-cmr@codefail.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 342afce10d upstream.
Setting ds->num_ports to DSA_MAX_PORTS made DSA core allocate unnecessary
dsa_port's and call mt7530_port_disable for non-existent ports.
Set it to MT7530_NUM_PORTS to fix that, and dsa_is_user_port check in
port_enable/disable is no longer required.
Cc: stable@vger.kernel.org
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b15fa9224e upstream.
Starting with kernel 5.11 built with CONFIG_FORTIFY_SOURCE mouting an
ocfs2 filesystem with either o2cb or pcmk cluster stack fails with the
trace below. Problem seems to be that strings for cluster stack and
cluster name are not guaranteed to be null terminated in the disk
representation, while strlcpy assumes that the source string is always
null terminated. This causes a read outside of the source string
triggering the buffer overflow detection.
detected buffer overflow in strlen
------------[ cut here ]------------
kernel BUG at lib/string.c:1149!
invalid opcode: 0000 [#1] SMP PTI
CPU: 1 PID: 910 Comm: mount.ocfs2 Not tainted 5.14.0-1-amd64 #1
Debian 5.14.6-2
RIP: 0010:fortify_panic+0xf/0x11
...
Call Trace:
ocfs2_initialize_super.isra.0.cold+0xc/0x18 [ocfs2]
ocfs2_fill_super+0x359/0x19b0 [ocfs2]
mount_bdev+0x185/0x1b0
legacy_get_tree+0x27/0x40
vfs_get_tree+0x25/0xb0
path_mount+0x454/0xa20
__x64_sys_mount+0x103/0x140
do_syscall_64+0x3b/0xc0
entry_SYSCALL_64_after_hwframe+0x44/0xae
Link: https://lkml.kernel.org/r/20210929180654.32460-1-vvidic@valentin-vidic.from.hr
Signed-off-by: Valentin Vidic <vvidic@valentin-vidic.from.hr>
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5314454ea3 upstream.
Commit 6dbf7bb555 ("fs: Don't invalidate page buffers in
block_write_full_page()") uncovered a latent bug in ocfs2 conversion
from inline inode format to a normal inode format.
The code in ocfs2_convert_inline_data_to_extents() attempts to zero out
the whole cluster allocated for file data by grabbing, zeroing, and
dirtying all pages covering this cluster. However these pages are
beyond i_size, thus writeback code generally ignores these dirty pages
and no blocks were ever actually zeroed on the disk.
This oversight was fixed by commit 693c241a5f ("ocfs2: No need to zero
pages past i_size.") for standard ocfs2 write path, inline conversion
path was apparently forgotten; the commit log also has a reasoning why
the zeroing actually is not needed.
After commit 6dbf7bb555, things became worse as writeback code stopped
invalidating buffers on pages beyond i_size and thus these pages end up
with clean PageDirty bit but with buffers attached to these pages being
still dirty. So when a file is converted from inline format, then
writeback triggers, and then the file is grown so that these pages
become valid, the invalid dirtiness state is preserved,
mark_buffer_dirty() does nothing on these pages (buffers are already
dirty) but page is never written back because it is clean. So data
written to these pages is lost once pages are reclaimed.
Simple reproducer for the problem is:
xfs_io -f -c "pwrite 0 2000" -c "pwrite 2000 2000" -c "fsync" \
-c "pwrite 4000 2000" ocfs2_file
After unmounting and mounting the fs again, you can observe that end of
'ocfs2_file' has lost its contents.
Fix the problem by not doing the pointless zeroing during conversion
from inline format similarly as in the standard write path.
[akpm@linux-foundation.org: fix whitespace, per Joseph]
Link: https://lkml.kernel.org/r/20210930095405.21433-1-jack@suse.cz
Fixes: 6dbf7bb555 ("fs: Don't invalidate page buffers in block_write_full_page()")
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Tested-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Acked-by: Gang He <ghe@suse.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Jun Piao <piaojun@huawei.com>
Cc: "Markov, Andrey" <Markov.Andrey@Dell.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1bd85aa65d upstream.
Currently, we check the wb_err too early for directories, before all of
the unsafe child requests have been waited on. In order to fix that we
need to check the mapping->wb_err later nearer to the end of ceph_fsync.
We also have an overly-complex method for tracking errors after
blocklisting. The errors recorded in cleanup_session_requests go to a
completely separate field in the inode, but we end up reporting them the
same way we would for any other error (in fsync).
There's no real benefit to tracking these errors in two different
places, since the only reporting mechanism for them is in fsync, and
we'd need to advance them both every time.
Given that, we can just remove i_meta_err, and convert the places that
used it to instead just use mapping->wb_err instead. That also fixes
the original problem by ensuring that we do a check_and_advance of the
wb_err at the end of the fsync op.
Cc: stable@vger.kernel.org
URL: https://tracker.ceph.com/issues/52864
Reported-by: Patrick Donnelly <pdonnell@redhat.com>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Xiubo Li <xiubli@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98d0a6fb73 upstream.
Currently when mounting, we may end up finding an existing superblock
that corresponds to a blocklisted MDS client. This means that the new
mount ends up being unusable.
If we've found an existing superblock with a client that is already
blocklisted, and the client is not configured to recover on its own,
fail the match. Ditto if the superblock has been forcibly unmounted.
While we're in here, also rename "other" to the more conventional "fsc".
Cc: stable@vger.kernel.org
URL: https://bugzilla.redhat.com/show_bug.cgi?id=1901499
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4fbe70c5c upstream.
The receiver should abort TP if 'total message size' in TP.CM_RTS and
TP.CM_BAM is less than 9 or greater than 1785 [1], but currently the
j1939 stack only checks the upper bound and the receiver will accept
the following broadcast message:
vcan1 18ECFF00 [8] 20 08 00 02 FF 00 23 01
vcan1 18EBFF00 [8] 01 00 00 00 00 00 00 00
vcan1 18EBFF00 [8] 02 00 FF FF FF FF FF FF
This patch adds check for the lower bound and abort illegal TP.
[1] SAE-J1939-82 A.3.4 Row 2 and A.3.6 Row 6.
Fixes: 9d71dd0c70 ("can: add support of SAE J1939 protocol")
Link: https://lore.kernel.org/all/1634203601-3460-1-git-send-email-zhangchangzhong@huawei.com
Cc: stable@vger.kernel.org
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9acf636215 upstream.
Using wait_event_interruptible() to wait for complete transmission,
but do not check the result of wait_event_interruptible() which can be
interrupted. It will result in TX buffer has multiple accessors and
the later process interferes with the previous process.
Following is one of the problems reported by syzbot.
=============================================================
WARNING: CPU: 0 PID: 0 at net/can/isotp.c:840 isotp_tx_timer_handler+0x2e0/0x4c0
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.13.0-rc7+ #68
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1 04/01/2014
RIP: 0010:isotp_tx_timer_handler+0x2e0/0x4c0
Call Trace:
<IRQ>
? isotp_setsockopt+0x390/0x390
__hrtimer_run_queues+0xb8/0x610
hrtimer_run_softirq+0x91/0xd0
? rcu_read_lock_sched_held+0x4d/0x80
__do_softirq+0xe8/0x553
irq_exit_rcu+0xf8/0x100
sysvec_apic_timer_interrupt+0x9e/0xc0
</IRQ>
asm_sysvec_apic_timer_interrupt+0x12/0x20
Add result check for wait_event_interruptible() in isotp_sendmsg()
to avoid multiple accessers for tx buffer.
Fixes: e057dd3fc2 ("can: add ISO 15765-2:2016 transport protocol")
Link: https://lore.kernel.org/all/10ca695732c9dd267c76a3c30f37aefe1ff7e32f.1633764159.git.william.xuanziyang@huawei.com
Cc: stable@vger.kernel.org
Reported-by: syzbot+78bab6958a614b0c80b9@syzkaller.appspotmail.com
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3cb958027c ]
When utilizing End to End delay mechanism, the following error messages show up:
|root@ehl1:~# ptp4l --tx_timestamp_timeout=50 -H -i eno2 -E -m
|ptp4l[950.573]: selected /dev/ptp3 as PTP clock
|ptp4l[950.586]: port 1: INITIALIZING to LISTENING on INIT_COMPLETE
|ptp4l[950.586]: port 0: INITIALIZING to LISTENING on INIT_COMPLETE
|ptp4l[952.879]: port 1: new foreign master 001395.fffe.4897b4-1
|ptp4l[956.879]: selected best master clock 001395.fffe.4897b4
|ptp4l[956.879]: port 1: assuming the grand master role
|ptp4l[956.879]: port 1: LISTENING to GRAND_MASTER on RS_GRAND_MASTER
|ptp4l[962.017]: port 1: received DELAY_REQ without timestamp
|ptp4l[962.273]: port 1: received DELAY_REQ without timestamp
|ptp4l[963.090]: port 1: received DELAY_REQ without timestamp
Commit f2fb6b6275 ("net: stmmac: enable timestamp snapshot for required PTP
packets in dwmac v5.10a") already addresses this problem for the dwmac
v5.10. However, same holds true for all dwmacs above version v4.10. Correct the
check accordingly. Afterwards everything works as expected.
Tested on Intel Atom(R) x6414RE Processor.
Fixes: 14f347334b ("net: stmmac: Correctly take timestamp for PTPv2")
Fixes: f2fb6b6275 ("net: stmmac: enable timestamp snapshot for required PTP packets in dwmac v5.10a")
Suggested-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0dd8a25f35 ]
HNS3 driver includes hns3.ko, hnae3.ko and hclge.ko.
hns3.ko includes network stack and pci_driver, hclge.ko includes
HW device action, algo_ops and timer task, hnae3.ko includes some
register function.
When SRIOV is enable and hclge.ko is removed, HW device is unloaded
but VF still exists, PF will not reply VF mbx messages, and cause
errors.
This patch fix it by disable SRIOV before remove hclge.ko.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1385cc81ba ]
The task of VF reset is performed through the workqueue. It checks the
value of hdev->reset_pending to determine whether to exit the loop.
However, the value of hdev->reset_pending may also be assigned by
the interrupt function hclgevf_misc_irq_handle(), which may cause the
loop fail to exit and keep occupying the workqueue. This loop is not
necessary, so remove it and the workqueue will be rescheduled if the
reset needs to be retried or a new reset occurs.
Fixes: 1cc9bc6e58 ("net: hns3: split hclgevf_reset() into preparing and rebuilding part")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68752b24f5 ]
Currently when there is a rx page allocation failure, it is
possible that polling may be stopped if there is no more packet
to be reveiced, which may cause queue stall problem under memory
pressure.
This patch makes sure polling is scheduled again when there is
any rx page allocation failure, and polling will try to allocate
receive buffers until it succeeds.
Now the allocation retry is added, it is unnecessary to do the rx
page allocation at the end of rx cleaning, so remove it. And reset
the unused_count to zero after calling hns3_nic_alloc_rx_buffers()
to avoid calling hns3_nic_alloc_rx_buffers() repeatedly under
memory pressure.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 731797fdff ]
If ets dwrr bandwidth of tc is set to 0, the hardware will switch to SP
mode. In this case, this tc may occupy all the tx bandwidth if it has
huge traffic, so it violates the purpose of the user setting.
To fix this problem, limit the ets dwrr bandwidth must greater than 0.
Fixes: cacde272dd ("net: hns3: Add hclge_dcb module for the support of DCB feature")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b63fcaab95 ]
Currently, DWRR of tc will be initialized to a fixed value when this tc
is enabled, but it is not been reset to 0 when this tc is disabled. It
cause a problem that the DWRR of unused tc is not 0 after using tc tool
to add and delete multi-tc parameters.
For examples, after enabling 4 TCs and restoring to 1 TC by follow
tc commands:
$ tc qdisc add dev eth0 root mqprio num_tc 4 map 0 1 2 3 0 1 2 3 queues \
8@0 8@8 8@16 8@24 hw 1 mode channel
$ tc qdisc del dev eth0 root
Now there is just one TC is enabled for eth0, but the tc info querying by
debugfs is shown as follow:
$ cat /mnt/hns3/0000:7d:00.0/tm/tc_sch_info
enabled tc number: 1
weight_offset: 14
TC MODE WEIGHT
0 dwrr 100
1 dwrr 100
2 dwrr 100
3 dwrr 100
4 dwrr 0
5 dwrr 0
6 dwrr 0
7 dwrr 0
This patch fixes it by resetting DWRR of tc to 0 when tc is disabled.
Fixes: 848440544b ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 787252a10d ]
With PREEMPT_COUNT=y, when a CPU is offlined and then onlined again, we
get:
BUG: scheduling while atomic: swapper/1/0/0x00000000
no locks held by swapper/1/0.
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.15.0-rc2+ #100
Call Trace:
dump_stack_lvl+0xac/0x108
__schedule_bug+0xac/0xe0
__schedule+0xcf8/0x10d0
schedule_idle+0x3c/0x70
do_idle+0x2d8/0x4a0
cpu_startup_entry+0x38/0x40
start_secondary+0x2ec/0x3a0
start_secondary_prolog+0x10/0x14
This is because powerpc's arch_cpu_idle_dead() decrements the idle task's
preempt count, for reasons explained in commit a7c2bb8279 ("powerpc:
Re-enable preemption before cpu_die()"), specifically "start_secondary()
expects a preempt_count() of 0."
However, since commit 2c669ef697 ("powerpc/preempt: Don't touch the idle
task's preempt_count during hotplug") and commit f1a0a376ca ("sched/core:
Initialize the idle task with preemption disabled"), that justification no
longer holds.
The idle task isn't supposed to re-enable preemption, so remove the
vestigial preempt_enable() from the CPU offline path.
Tested with pseries and powernv in qemu, and pseries on PowerVM.
Fixes: 2c669ef697 ("powerpc/preempt: Don't touch the idle task's preempt_count during hotplug")
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211015173902.2278118-1-nathanl@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4cce60f15c ]
Both arch/nios2/ and drivers/mmc/host/tmio_mmc.c define a macro
with the name "CTL_STATUS". Change the one in arch/nios2/ to be
"CTL_FSTATUS" (flags status) to eliminate the build warning.
In file included from ../drivers/mmc/host/tmio_mmc.c:22:
drivers/mmc/host/tmio_mmc.h:31: warning: "CTL_STATUS" redefined
31 | #define CTL_STATUS 0x1c
arch/nios2/include/asm/registers.h:14: note: this is the location of the previous definition
14 | #define CTL_STATUS 0
Fixes: b31ebd8055 ("nios2: Nios2 registers")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66d262804a ]
I compared the register definitions with the D-Link DWR-966
GPL sources and found that the PUAFD field definition was
incorrect. This definition is unused and causes no issues.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86f1e3a848 ]
With net.ipv4.tcp_l3mdev_accept=1 it is possible for a listen socket to
accept connection from the same client address in different VRFs. It is
also possible to set different MD5 keys for these clients which differ
only in the tcpm_l3index field.
This appears to work when distinguishing between different VRFs but not
between non-VRF and VRF connections. In particular:
* tcp_md5_do_lookup_exact will match a non-vrf key against a vrf key.
This means that adding a key with l3index != 0 after a key with l3index
== 0 will cause the earlier key to be deleted. Both keys can be present
if the non-vrf key is added later.
* _tcp_md5_do_lookup can match a non-vrf key before a vrf key. This
casues failures if the passwords differ.
Fix this by making tcp_md5_do_lookup_exact perform an actual exact
comparison on l3index and by making __tcp_md5_do_lookup perfer
vrf-bound keys above other considerations like prefixlen.
Fixes: dea53bb80e ("tcp: Add l3index to tcp_md5sig_key and md5 functions")
Signed-off-by: Leonard Crestez <cdleonard@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46393d61a3 ]
Fix the following build/link error by adding a dependency on the CRC32
routines:
ld: drivers/net/usb/lan78xx.o: in function `lan78xx_set_multicast':
lan78xx.c:(.text+0x48cf): undefined reference to `crc32_le'
The actual use of crc32_le() comes indirectly through ether_crc().
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 174c376278 ]
Because the data pointer of net/ipv4/vs/debug_level is not updated per
netns, it must be marked as read-only in non-init netns.
Fixes: c6d2d445d8 ("IPVS: netns, final patch enabling network name space.")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a482c5e00a ]
In rt_mt6(), when it's a nonlinear skb, the 1st skb_header_pointer()
only copies sizeof(struct ipv6_rt_hdr) to _route that rh points to.
The access by ((const struct rt0_hdr *)rh)->reserved will overflow
the buffer. So this access should be moved below the 2nd call to
skb_header_pointer().
Besides, after the 2nd skb_header_pointer(), its return value should
also be checked, othersize, *rp may cause null-pointer-ref.
v1->v2:
- clean up some old debugging log.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4c2efa139 ]
Correct parameters order in call to ice_tunnel_idx_to_entry function.
Entry in sparse port table is correct when the idx is 0. For idx 1 one
correct entry should be skipped, for idx 2 two of them should be skipped
etc. Change if condition to be true when idx is 0, which means that
previous valid entry of this tunnel type were skipped.
Fixes: b20e6c17c4 ("ice: convert to new udp_tunnel infrastructure")
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b9b546dc0 ]
There is a noise issue for 8kHz sample rate on slave mode.
Compared with master mode, the difference is the DACDIV
setting, after correcting the DACDIV, the noise is gone.
There is no noise issue for 48kHz sample rate, because
the default value of DACDIV is correct for 48kHz.
So wm8960_configure_clocking() should be functional for
ADC and DAC function even if it is slave mode.
In order to be compatible for old use case, just add
condition for checking that sysclk is zero with
slave mode.
Fixes: 0e50b51aa2 ("ASoC: wm8960: Let wm8960 driver configure its bit clock and frame clock")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/1634102224-3922-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 293d92cbbd ]
The following warning occurred sporadically on s390:
DMA-API: nvme 0006:00:00.0: device driver maps memory from kernel text or rodata [addr=0000000048cc5e2f] [len=131072]
WARNING: CPU: 4 PID: 825 at kernel/dma/debug.c:1083 check_for_illegal_area+0xa8/0x138
It is a false-positive warning, due to broken logic in debug_dma_map_sg().
check_for_illegal_area() checks for overlay of sg elements with kernel text
or rodata. It is called with sg_dma_len(s) instead of s->length as
parameter. After the call to ->map_sg(), sg_dma_len() will contain the
length of possibly combined sg elements in the DMA address space, and not
the individual sg element length, which would be s->length.
The check will then use the physical start address of an sg element, and
add the DMA length for the overlap check, which could result in the false
warning, because the DMA length can be larger than the actual single sg
element length.
In addition, the call to check_for_illegal_area() happens in the iteration
over mapped_ents, which will not include all individual sg elements if
any of them were combined in ->map_sg().
Fix this by using s->length instead of sg_dma_len(s). Also put the call to
check_for_illegal_area() in a separate loop, iterating over all the
individual sg elements ("nents" instead of "mapped_ents").
While at it, as suggested by Robin Murphy, also move check_for_stack()
inside the new loop, as it is similarly concerned with validating the
individual sg elements.
Link: https://lore.kernel.org/lkml/20210705185252.4074653-1-gerald.schaefer@linux.ibm.com
Fixes: 884d05970b ("dma-debug: use sg_dma_len accessor")
Signed-off-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c20106944e ]
If nfsd has existing listening sockets without any processes, then an error
returned from svc_create_xprt() for an additional transport will remove
those existing listeners. We're seeing this in practice when userspace
attempts to create rpcrdma transports without having the rpcrdma modules
present before creating nfsd kernel processes. Fix this by checking for
existing sockets before calling nfsd_destroy().
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 012e974501 ]
Rebooting xtensa images loaded with the '-kernel' option in qemu does
not work. When executing a reboot command, the qemu session either hangs
or experiences an endless sequence of error messages.
Kernel panic - not syncing: Unrecoverable error in exception handler
Reset code jumps to the CPU restart address, but Linux can not recover
from there because code and data in the kernel init sections have been
discarded and overwritten at this point.
XTFPGA platforms have a means to reset the CPU by writing 0xdead into a
specific FPGA IO address. When used in QEMU the kernel image loaded with
the '-kernel' option gets restored to its original state allowing the
machine to boot successfully.
Use that mechanism to attempt a platform reset. If it does not work,
fall back to the existing mechanism.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3d7c2cdf6 ]
Use platform data to initialize xtfpga device drivers when CONFIG_USE_OF
is not selected. This fixes xtfpga networking when CONFIG_USE_OF is not
selected but CONFIG_OF is.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9172b5c4a7 ]
Like xen_start_flags, xen_domain_type gets set before .bss gets cleared.
Hence this variable also needs to be prevented from getting put in .bss,
which is possible because XEN_NATIVE is an enumerator evaluating to
zero. Any use prior to init_hvm_pv_info() setting the variable again
would lead to wrong decisions; one such case is xenboot_console_setup()
when called as a result of "earlyprintk=xen".
Use __ro_after_init as more applicable than either __section(".data") or
__read_mostly.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/d301677b-6f22-5ae6-bd36-458e1f323d0b@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
The linux-5.10.y backport of commit "io_uring: add ->splice_fd_in checks"
includes a typo: "|" where "||" should be. (The original upstream commit
is fine.)
Fixes: 54eb6211b9 ("io_uring: add ->splice_fd_in checks")
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org # v5.10
Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f1fce595b upstream.
Fix lots of fallthrough warnings, e.g.:
arch/parisc/math-emu/fpudispatch.c:323:33: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both the firmware audio driver and the vc4-kms-v3d driver are capable
of providing HDMI audio, but only one should be active at any time.
The vc4-kms-v3d overlays disable the firmware audio driver, but they
also have a noaudio parameter that as well as disabling the ARM-side
HDMI audio also re-enables the firmware HDMI audio. This is not
guaranteed to work and has been seen to break the display completely.
Modify the noaudio parameters so that the firmware HDMI audio support
remains disabled.
See: https://github.com/raspberrypi/linux/issues/4651
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Limit the number of allowed video callbacks. This helps with limiting
the size of the coded input FIFO which in turn helps to control latency.
Choose -5 as the magic number as it translates to DPB+5 buffers which
has been proven to be a good number in the past.
Ideally coded buffers would not be returned to the user until they
had been decoded into the DPB or been discarded as bad, but that grade
of control is unavailable to us.
Signed-off-by: John Cox <jc@kynesim.co.uk>
Commit db8e94e7cf upstream
The existing link format validation failure debug message in media-entity.c
helped to pinpoint the point of failure but provided no additional
information what's wrong. Tell the user exactly why the validation failed.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Adds Media Controller API support for more complex pipelines.
libcamera is about to switch to using this mechanism for configuring
sensors.
This can be enabled by either a module parameter, or device tree.
Various functions have been moved to group video-centric and
mc-centric functions together.
Based on a similar conversion done to ti-vpe.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The driver was making big assumptions about the source device
using pad 0 and 1, which doesn't follow for more complex
devices where Unicam's source device may be a sink device for
something else.
Read the pad numbers through media controller, and reference
them appropriately.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
RAW color spaces are more usually reported as having full range
quantization.
Tested using libcamera.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
commit 4a3e0aeddf upstream.
mv88e6xxx_port_ppu_updates() interpretes data in the PORT_STS
register incorrectly for internal ports (ie no PPU). In these
cases, the PHY_DETECT bit indicates link status. This results
in forcing the MAC state whenever the PHY link goes down which
is not intended. As a side effect, LED's configured to show
link status stay lit even though the physical link is down.
Add a check in mac_link_down and mac_link_up to see if it
concerns an external port and only then, look at PPU status.
Fixes: 5d5b231da7 (net: dsa: mv88e6xxx: use PHY_DETECT in mac_link_up/mac_link_down)
Reported-by: Maarten Zanders <m.zanders@televic.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Maarten Zanders <maarten.zanders@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c976a5657 upstream.
Bridging, and possibly other upper stack gizmos, adds the
lower device's netdev->dev_addr to its own uc list, and
then requests it be deleted when the upper bridge device is
removed. This delete request also happens with the bridging
vlan_filtering is enabled and then disabled.
Bonding has a similar behavior with the uc list, but since it
also uses set_mac to manage netdev->dev_addr, it doesn't have
the same the failure case.
Because we store our netdev->dev_addr in our uc list, we need
to ignore the delete request from dev_uc_sync so as to not
lose the address and all hope of communicating. Note that
ndo_set_mac_address is expressly changing netdev->dev_addr,
so no limitation is set there.
Fixes: 2a654540be ("ionic: Add Rx filter and rx_mode ndo support")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9fde506e0c upstream.
When skb_match is NULL, it means we received a PTP IRQ for a timestamp
ID that the kernel has no idea about, since there is no skb in the
timestamping queue with that timestamp ID.
This is a grave error and not something to just "continue" over.
So print a big warning in case this happens.
Also, move the check above ocelot_get_hwtimestamp(), there is no point
in reading the full 64-bit current PTP time if we're not going to do
anything with it anyway for this skb.
Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9973a43012 upstream.
Fix the following build/link errors by adding a dependency on
CRYPTO, CRYPTO_HASH, CRYPTO_SHA256 and CRC32:
ld: drivers/net/usb/r8152.o: in function `rtl8152_fw_verify_checksum':
r8152.c:(.text+0x2b2a): undefined reference to `crypto_alloc_shash'
ld: r8152.c:(.text+0x2bed): undefined reference to `crypto_shash_digest'
ld: r8152.c:(.text+0x2c50): undefined reference to `crypto_destroy_tfm'
ld: drivers/net/usb/r8152.o: in function `_rtl8152_set_rx_mode':
r8152.c:(.text+0xdcb0): undefined reference to `crc32_le'
Fixes: 9370f2d05a ("r8152: support request_firmware for RTL8153")
Fixes: ac718b6930 ("net/usb: new driver for RTL8152")
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5a14ea7b4 upstream.
The error code is missing in this code scenario, add the error code
'-EINVAL' to the return value 'rc'.
Eliminate the follow smatch warning:
drivers/net/ethernet/qlogic/qed/qed_main.c:1298 qed_slowpath_start()
warn: missing error code 'rc'.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Fixes: d51e4af5c2 ("qed: aRFS infrastructure support")
Signed-off-by: chongjiapeng <jiapeng.chong@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1413269086 upstream.
Introduction of lockless subqueues broke the class statistics.
Before the change stats were accumulated in `bstats' and `qstats'
on the stack which was then copied to struct gnet_dump.
After the change the `bstats' and `qstats' are initialized to 0
and never updated, yet still fed to gnet_dump. The code updates
the global qdisc->cpu_bstats and qdisc->cpu_qstats instead,
clobbering them. Most likely a copy-paste error from the code in
mqprio_dump().
__gnet_stats_copy_basic() and __gnet_stats_copy_queue() accumulate
the values for per-CPU case but for global stats they overwrite
the value, so only stats from the last loop iteration / tc end up
in sch->[bq]stats.
Use the on-stack [bq]stats variables again and add the stats manually
in the global case.
Fixes: ce679e8df7 ("net: sched: add support for TCQ_F_NOLOCK subqueues to sch_mqprio")
Cc: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
https://lore.kernel.org/all/20211007175000.2334713-2-bigeasy@linutronix.de/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 596143e3ae upstream.
Fix modpost Section mismatch error in next_platform_timer().
[...]
WARNING: modpost: vmlinux.o(.text.unlikely+0x26e60): Section mismatch in reference from the function next_platform_timer() to the variable .init.data:acpi_gtdt_desc
The function next_platform_timer() references
the variable __initdata acpi_gtdt_desc.
This is often because next_platform_timer lacks a __initdata
annotation or the annotation of acpi_gtdt_desc is wrong.
WARNING: modpost: vmlinux.o(.text.unlikely+0x26e64): Section mismatch in reference from the function next_platform_timer() to the variable .init.data:acpi_gtdt_desc
The function next_platform_timer() references
the variable __initdata acpi_gtdt_desc.
This is often because next_platform_timer lacks a __initdata
annotation or the annotation of acpi_gtdt_desc is wrong.
ERROR: modpost: Section mismatches detected.
Set CONFIG_SECTION_MISMATCH_WARN_ONLY=y to allow them.
make[1]: *** [scripts/Makefile.modpost:59: vmlinux.symvers] Error 1
make[1]: *** Deleting file 'vmlinux.symvers'
make: *** [Makefile:1176: vmlinux] Error 2
[...]
Fixes: a712c3ed9b ("acpi/arm64: Add memory-mapped timer support in GTDT driver")
Signed-off-by: Jackie Liu <liuyun01@kylinos.cn>
Acked-by: Hanjun Guo <guohanjun@huawei.com>
Link: https://lore.kernel.org/r/20210823092526.2407526-1-liu.yun@linux.dev
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14eb0cb4e9 upstream.
In theory a context can be destroyed and a new one allocated at the same
address, making the pointer comparision to detect when we don't need to
update the current pagetables invalid. Instead assign a sequence number
to each context on creation, and use this for the check.
Fixes: 84c31ee16f ("drm/msm/a6xx: Add support for per-instance pagetables")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97794170b6 upstream.
In commit e11f5bd822 ("drm: Add support for DP 1.4 Compliance edid
corruption test") the function connector_bad_edid() started assuming
that the memory for the EDID passed to it was big enough to hold
`edid[0x7e] + 1` blocks of data (1 extra for the base block). It
completely ignored the fact that the function was passed `num_blocks`
which indicated how much memory had been allocated for the EDID.
Let's fix this by adding a bounds check.
This is important for handling the case where there's an error in the
first block of the EDID. In that case we will call
connector_bad_edid() without having re-allocated memory based on
`edid[0x7e]`.
Fixes: e11f5bd822 ("drm: Add support for DP 1.4 Compliance edid corruption test")
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211005192905.v2.1.Ib059f9c23c2611cb5a9d760e7d0a700c1295928d@changeid
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 75b3cb97eb upstream.
Intermittent Kernel crash has been observed on probe in
bcm_qspi_mspi_l2_isr() handler when the MSPI spifie interrupt bit
has not been cleared before registering for interrupts.
Fix the driver to move SoC specific custom interrupt handling code
before we register IRQ in probe. Also clear MSPI interrupt status
resgiter prior to registering IRQ handlers.
Fixes: cc20a38612 ("spi: iproc-qspi: Add Broadcom iProc SoCs support")
Signed-off-by: Kamal Dasu <kdasu@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211008203603.40915-3-kdasu.kdev@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b02420169 upstream.
Change kstrtou32() argument 'base' to be zero instead of 'len'.
It works by chance for setting one bit value, but it is not supposed to
work in case value passed to mlxreg_io_attr_store() is greater than 1.
It works for example, for:
echo 1 > /sys/devices/platform/mlxplat/mlxreg-io/hwmon/.../jtag_enable
But it will fail for:
echo n > /sys/devices/platform/mlxplat/mlxreg-io/hwmon/.../jtag_enable,
where n > 1.
The flow for input buffer conversion is as below:
_kstrtoull(const char *s, unsigned int base, unsigned long long *res)
calls:
rv = _parse_integer(s, base, &_res);
For the second case, where n > 1:
- _parse_integer() converts 's' to 'val'.
For n=2, 'len' is set to 2 (string buffer is 0x32 0x0a), for n=3
'len' is set to 3 (string buffer 0x33 0x0a), etcetera.
- 'base' is equal or greater then '2' (length of input buffer).
As a result, _parse_integer() exits with result zero (rv):
rv = 0;
while (1) {
...
if (val >= base)-> (2 >= 2)
break;
...
rv++;
...
}
And _kstrtoull() in their turn will fail:
if (rv == 0)
return -EINVAL;
Fixes: 5ec4a8ace0 ("platform/mellanox: Introduce support for Mellanox register access driver")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20210927142214.2613929-2-vadimp@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 332fdf951d upstream.
Currently, mlxsw allows cooling states to be set above the maximum
cooling state supported by the driver:
# cat /sys/class/thermal/thermal_zone2/cdev0/type
mlxsw_fan
# cat /sys/class/thermal/thermal_zone2/cdev0/max_state
10
# echo 18 > /sys/class/thermal/thermal_zone2/cdev0/cur_state
# echo $?
0
This results in out-of-bounds memory accesses when thermal state
transition statistics are enabled (CONFIG_THERMAL_STATISTICS=y), as the
transition table is accessed with a too large index (state) [1].
According to the thermal maintainer, it is the responsibility of the
driver to reject such operations [2].
Therefore, return an error when the state to be set exceeds the maximum
cooling state supported by the driver.
To avoid dead code, as suggested by the thermal maintainer [3],
partially revert commit a421ce088a ("mlxsw: core: Extend cooling
device with cooling levels") that tried to interpret these invalid
cooling states (above the maximum) in a special way. The cooling levels
array is not removed in order to prevent the fans going below 20% PWM,
which would cause them to get stuck at 0% PWM.
[1]
BUG: KASAN: slab-out-of-bounds in thermal_cooling_device_stats_update+0x271/0x290
Read of size 4 at addr ffff8881052f7bf8 by task kworker/0:0/5
CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted 5.15.0-rc3-custom-45935-gce1adf704b14 #122
Hardware name: Mellanox Technologies Ltd. "MSN2410-CB2FO"/"SA000874", BIOS 4.6.5 03/08/2016
Workqueue: events_freezable_power_ thermal_zone_device_check
Call Trace:
dump_stack_lvl+0x8b/0xb3
print_address_description.constprop.0+0x1f/0x140
kasan_report.cold+0x7f/0x11b
thermal_cooling_device_stats_update+0x271/0x290
__thermal_cdev_update+0x15e/0x4e0
thermal_cdev_update+0x9f/0xe0
step_wise_throttle+0x770/0xee0
thermal_zone_device_update+0x3f6/0xdf0
process_one_work+0xa42/0x1770
worker_thread+0x62f/0x13e0
kthread+0x3ee/0x4e0
ret_from_fork+0x1f/0x30
Allocated by task 1:
kasan_save_stack+0x1b/0x40
__kasan_kmalloc+0x7c/0x90
thermal_cooling_device_setup_sysfs+0x153/0x2c0
__thermal_cooling_device_register.part.0+0x25b/0x9c0
thermal_cooling_device_register+0xb3/0x100
mlxsw_thermal_init+0x5c5/0x7e0
__mlxsw_core_bus_device_register+0xcb3/0x19c0
mlxsw_core_bus_device_register+0x56/0xb0
mlxsw_pci_probe+0x54f/0x710
local_pci_probe+0xc6/0x170
pci_device_probe+0x2b2/0x4d0
really_probe+0x293/0xd10
__driver_probe_device+0x2af/0x440
driver_probe_device+0x51/0x1e0
__driver_attach+0x21b/0x530
bus_for_each_dev+0x14c/0x1d0
bus_add_driver+0x3ac/0x650
driver_register+0x241/0x3d0
mlxsw_sp_module_init+0xa2/0x174
do_one_initcall+0xee/0x5f0
kernel_init_freeable+0x45a/0x4de
kernel_init+0x1f/0x210
ret_from_fork+0x1f/0x30
The buggy address belongs to the object at ffff8881052f7800
which belongs to the cache kmalloc-1k of size 1024
The buggy address is located 1016 bytes inside of
1024-byte region [ffff8881052f7800, ffff8881052f7c00)
The buggy address belongs to the page:
page:0000000052355272 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x1052f0
head:0000000052355272 order:3 compound_mapcount:0 compound_pincount:0
flags: 0x200000000010200(slab|head|node=0|zone=2)
raw: 0200000000010200 ffffea0005034800 0000000300000003 ffff888100041dc0
raw: 0000000000000000 0000000000100010 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8881052f7a80: 00 00 00 00 00 00 04 fc fc fc fc fc fc fc fc fc
ffff8881052f7b00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff8881052f7b80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^
ffff8881052f7c00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff8881052f7c80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[2] https://lore.kernel.org/linux-pm/9aca37cb-1629-5c67-1895-1fdc45c0244e@linaro.org/
[3] https://lore.kernel.org/linux-pm/af9857f2-578e-de3a-e62b-6baff7e69fd4@linaro.org/
CC: Daniel Lezcano <daniel.lezcano@linaro.org>
Fixes: a50c1e3565 ("mlxsw: core: Implement thermal zone")
Fixes: a421ce088a ("mlxsw: core: Extend cooling device with cooling levels")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20211012174955.472928-1-idosch@idosch.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 776c750108 upstream.
I got a null-ptr-deref report:
KASAN: null-ptr-deref in range [0x0000000000000090-0x0000000000000097]
...
RIP: 0010:regulator_enable+0x84/0x260
...
Call Trace:
ahci_platform_enable_regulators+0xae/0x320
ahci_platform_enable_resources+0x1a/0x120
ahci_probe+0x4f/0x1b9
platform_probe+0x10b/0x280
...
entry_SYSCALL_64_after_hwframe+0x44/0xae
If devm_regulator_get() in ahci_platform_get_resources() fails,
hpriv->phy_regulator will point to NULL, when enabling or disabling it,
null-ptr-deref will occur.
ahci_probe()
ahci_platform_get_resources()
devm_regulator_get(, "phy") // failed, let phy_regulator = NULL
ahci_platform_enable_resources()
ahci_platform_enable_regulators()
regulator_enable(hpriv->phy_regulator) // null-ptr-deref
commit 962399bb7f ("ata: libahci_platform: Fix regulator_get_optional()
misuse") replaces devm_regulator_get_optional() with devm_regulator_get(),
but PHY regulator omits to delete "hpriv->phy_regulator = NULL;" like AHCI.
Delete it like AHCI regulator to fix this bug.
Fixes: commit 962399bb7f ("ata: libahci_platform: Fix regulator_get_optional() misuse")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 291c932fc3 upstream.
'skb' is allocated in digital_in_send_sdd_req(), but not free when
digital_in_send_cmd() failed, which will cause memory leak. Fix it
by freeing 'skb' if digital_in_send_cmd() return failed.
Fixes: 2c66daecc4 ("NFC Digital: Add NFC-A technology support")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58e7dcc9ca upstream.
'params' is allocated in digital_tg_listen_mdaa(), but not free when
digital_send_cmd() failed, which will cause memory leak. Fix it by
freeing 'params' if digital_send_cmd() return failed.
Fixes: 1c7a4c24fb ("NFC Digital: Add target NFC-DEP support")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40507e7aad upstream.
After recent cleanups, gcc started warning about a suspicious
memcpy() call during the s2io_io_resume() function:
In function '__dev_addr_set',
inlined from 'eth_hw_addr_set' at include/linux/etherdevice.h:318:2,
inlined from 's2io_set_mac_addr' at drivers/net/ethernet/neterion/s2io.c:5205:2,
inlined from 's2io_io_resume' at drivers/net/ethernet/neterion/s2io.c:8569:7:
arch/x86/include/asm/string_32.h:182:25: error: '__builtin_memcpy' accessing 6 bytes at offsets 0 and 2 overlaps 4 bytes at offset 2 [-Werror=restrict]
182 | #define memcpy(t, f, n) __builtin_memcpy(t, f, n)
| ^~~~~~~~~~~~~~~~~~~~~~~~~
include/linux/netdevice.h:4648:9: note: in expansion of macro 'memcpy'
4648 | memcpy(dev->dev_addr, addr, len);
| ^~~~~~
What apparently happened is that an old cleanup changed the calling
conventions for s2io_set_mac_addr() from taking an ethernet address
as a character array to taking a struct sockaddr, but one of the
callers was not changed at the same time.
Change it to instead call the low-level do_s2io_prog_unicast() function
that still takes the old argument type.
Fixes: 2fd3768845 ("S2io: Added support set_mac_address driver entry point")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211013143613.2049096-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef1100ef20 upstream.
When the ksz module is installed and removed using rmmod, kernel crashes
with null pointer dereferrence error. During rmmod, ksz_switch_remove
function tries to cancel the mib_read_workqueue using
cancel_delayed_work_sync routine and unregister switch from dsa.
During dsa_unregister_switch it calls ksz_mac_link_down, which in turn
reschedules the workqueue since mib_interval is non-zero.
Due to which queue executed after mib_interval and it tries to access
dp->slave. But the slave is unregistered in the ksz_switch_remove
function. Hence kernel crashes.
To avoid this crash, before canceling the workqueue, resetted the
mib_interval to 0.
v1 -> v2:
-Removed the if condition in ksz_mib_read_work
Fixes: 469b390e1b ("net: dsa: microchip: use delayed_work instead of timer + work")
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 075da584ba upstream.
Some old IPs do not provide the hardware feature register.
On these IPs, this register is read 0x00000000.
In old driver version, this feature was handled but a regression came
with the commit f10a6a3541 ("stmmac: rework get_hw_feature function").
Indeed, this commit removes the return value in dma->get_hw_feature().
This return value was used to indicate the validity of retrieved
information and used later on in stmmac_hw_init() to override
priv->plat data if this hardware feature were valid.
This patch restores the return code in ->get_hw_feature() in order
to indicate the hardware feature validity and override priv->plat
data only if this hardware feature is valid.
Fixes: f10a6a3541 ("stmmac: rework get_hw_feature function")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0bc73ad46a upstream.
Due to current HW arch limitations, RX-FCS (scattering FCS frame field
to software) and RX-port-timestamp (improved timestamp accuracy on the
receive side) can't work together.
RX-port-timestamp is not controlled by the user and it is enabled by
default when supported by the HW/FW.
This patch sets RX-port-timestamp opposite to RX-FCS configuration.
Fixes: 102722fc68 ("net/mlx5e: Add support for RXFCS feature flag")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e599ee234a upstream.
Fix the following build/link error by adding a dependency on the CRC32
routines:
ld: drivers/net/ethernet/arc/emac_main.o: in function `arc_emac_set_rx_mode':
emac_main.c:(.text+0xb11): undefined reference to `crc32_le'
The crc32_le() call comes through the ether_crc_le() call in
arc_emac_set_rx_mode().
[v2: moved the select to ARC_EMAC_CORE; the Makefile is a bit confusing,
but the error comes from emac_main.o, which is part of the arc_emac module,
which in turn is enabled by CONFIG_ARC_EMAC_CORE. Note that arc_emac is
different from emac_arc...]
Fixes: 775dd682e2 ("arc_emac: implement promiscuous mode and multicast filtering")
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Link: https://lore.kernel.org/r/20211012093446.1575-1-vegard.nossum@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 55a9968c7e upstream.
The commit 15add06841 ("gpio: pca953x: add ->set_config implementation")
introduced support for bias setting. However this, due to being half-baked,
brought potential issues:
- the turning bias via disabling makes the pin floating for a while;
- once enabled, bias can't be disabled.
Fix all these by adding support for bias disabling and move the disabling
part under the corresponding conditional.
While at it, add support for default setting, since it's cheap to add.
Fixes: 15add06841 ("gpio: pca953x: add ->set_config implementation")
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85f74acf09 upstream.
The request tag is no longer the only component of the command id.
Fixes: e7006de6c2 ("nvme: code command_id with a genctr for use-after-free validation")
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13dbc954b3 upstream.
dtbs_check currently complains that:
arch/arm/boot/dts/bcm2711-rpi-4-b.dts:220.10-231.4: Warning
(pci_device_reg): /scb/pcie@7d500000/pci@1,0: PCI unit address format
error, expected "0,0"
Unsurprisingly pci@0,0 is the right address, as illustrated by its reg
property:
&pcie0 {
pci@0,0 {
/*
* As defined in the IEEE Std 1275-1994 document,
* reg is a five-cell address encoded as (phys.hi
* phys.mid phys.lo size.hi size.lo). phys.hi
* should contain the device's BDF as 0b00000000
* bbbbbbbb dddddfff 00000000. The other cells
* should be zero.
*/
reg = <0 0 0 0 0>;
};
};
The device is clearly 0. So fix it.
Also add a missing 'device_type = "pci"'.
Fixes: 258f92d2f8 ("ARM: dts: bcm2711: Add reset controller to xHCI node")
Suggested-by: Rob Herring <robh@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210831125843.1233488-1-nsaenzju@redhat.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f565d0ead upstream.
When OP-TEE driver is built as a module, OP-TEE client devices
registered on TEE bus during probe should be unregistered during
optee_remove. So implement optee_unregister_devices() accordingly.
Fixes: c3fa24af92 ("tee: optee: add TEE bus device enumeration support")
Reported-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a913270e5 upstream.
In Sigma-Delta devices the SDO line is also used as an interrupt.
Leaving IRQ on level instead of falling might trigger a sample read
when the IRQ is enabled, as the SDO line is already low. Not sure
if SDO line will always immediately go high in ad_sd_buffer_postenable
before the IRQ is enabled.
Also the datasheet seem to explicitly say the falling edge of the SDO
should be used as an interrupt:
>From the AD7793 datasheet: " The DOUT/RDY falling edge can be
used as an interrupt to a processor"
Fixes: da4d3d6bb9 ("iio: adc: ad-sigma-delta: Allow custom IRQ flags")
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210906065630.16325-4-alexandru.tachici@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e081102f30 upstream.
Correct IRQ flag here is falling.
In Sigma-Delta devices the SDO line is also used as an interrupt.
Leaving IRQ on level instead of falling might trigger a sample read
when the IRQ is enabled, as the SDO line is already low. Not sure
if SDO line will always immediately go high in ad_sd_buffer_postenable
before the IRQ is enabled.
Also the datasheet seem to explicitly say the falling edge of the SDO
should be used as an interrupt:
>From the AD7780 datasheet: " The DOUT/Figure 22 RDY falling edge
can be used as an interrupt to a processor"
Fixes: da4d3d6bb9 ("iio: adc: ad-sigma-delta: Allow custom IRQ flags")
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210906065630.16325-3-alexandru.tachici@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89a86da5cb upstream.
IRQ type in ad_sigma_delta_info struct was missing.
In Sigma-Delta devices the SDO line is also used as an interrupt.
Leaving IRQ on level instead of falling might trigger a sample read
when the IRQ is enabled, as the SDO line is already low. Not sure
if SDO line will always immediately go high in ad_sd_buffer_postenable
before the IRQ is enabled.
Also the datasheet seem to explicitly say the falling edge of the SDO
should be used as an interrupt:
>From the AD7192 datasheet: "The DOUT/RDY falling edge can be used
as an interrupt to a processor,"
Fixes: da4d3d6bb9 ("iio: adc: ad-sigma-delta: Allow custom IRQ flags")
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210906065630.16325-2-alexandru.tachici@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f729a592ad upstream.
SYNC_STATE_ONLY device links intentionally allow cycles because cyclic
sync_state() dependencies are valid and necessary.
However a SYNC_STATE_ONLY device link where the consumer and the supplier
are the same device is pointless because the device link would be deleted
as soon as the device probes (because it's also the consumer) and won't
affect when the sync_state() callback is called. It's a waste of CPU cycles
and memory to create this device link. So reject any attempts to create
such a device link.
Fixes: 05ef983e0d ("driver core: Add device link support for SYNC_STATE_ONLY flag")
Cc: stable <stable@vger.kernel.org>
Reported-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20210929190549.860541-1-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f779e1d35 upstream.
When an interrupt is passed through, the KVM XIVE device calls the
set_vcpu_affinity() handler which raises the P bit to mask the
interrupt and to catch any in-flight interrupts while routing the
interrupt to the guest.
On the guest side, drivers (like some Intels) can request at probe
time some MSIs and call synchronize_irq() to check that there are no
in flight interrupts. This will call the XIVE get_irqchip_state()
handler which will always return true as the interrupt P bit has been
set on the host side and lock the CPU in an infinite loop.
Fix that by discarding disabled interrupts in get_irqchip_state().
Fixes: da15c03b04 ("powerpc/xive: Implement get_irqchip_state method for XIVE to fix shutdown race")
Cc: stable@vger.kernel.org #v5.4+
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Tested-by: seeteena <s1seetee@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211011070203.99726-1-clg@kaod.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 711885906b upstream.
This Kconfig option was added initially so that memory encryption is
enabled by default on machines which support it.
However, devices which have DMA masks that are less than the bit
position of the encryption bit, aka C-bit, require the use of an IOMMU
or the use of SWIOTLB.
If the IOMMU is disabled or in passthrough mode, the kernel would switch
to SWIOTLB bounce-buffering for those transfers.
In order to avoid that,
2cc13bb4f5 ("iommu: Disable passthrough mode when SME is active")
disables the default IOMMU passthrough mode so that devices for which the
default 256K DMA is insufficient, can use the IOMMU instead.
However 2, there are cases where the IOMMU is disabled in the BIOS, etc.
(think the usual hardware folk "oops, I dropped the ball there" cases) or a
driver doesn't properly use the DMA APIs or a device has a firmware or
hardware bug, e.g.:
ea68573d40 ("drm/amdgpu: Fail to load on RAVEN if SME is active")
However 3, in the above GPU use case, there are APIs like Vulkan and
some OpenGL/OpenCL extensions which are under the assumption that
user-allocated memory can be passed in to the kernel driver and both the
GPU and CPU can do coherent and concurrent access to the same memory.
That cannot work with SWIOTLB bounce buffers, of course.
So, in order for those devices to function, drop the "default y" for the
SME by default active option so that users who want to have SME enabled,
will need to either enable it in their config or use "mem_encrypt=on" on
the kernel command line.
[ tlendacky: Generalize commit message. ]
Fixes: 7744ccdbc1 ("x86/mm: Add Secure Memory Encryption (SME) support")
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/8bbacd0e-4580-3194-19d2-a0ecad7df09c@molgen.mpg.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d388fa01f upstream.
If a cell has 'nbits' equal to a multiple of BITS_PER_BYTE the logic
*p &= GENMASK((cell->nbits%BITS_PER_BYTE) - 1, 0);
will become undefined behavior because nbits modulo BITS_PER_BYTE is 0, and we
subtract one from that making a large number that is then shifted more than the
number of bits that fit into an unsigned long.
UBSAN reports this problem:
UBSAN: shift-out-of-bounds in drivers/nvmem/core.c:1386:8
shift exponent 64 is too large for 64-bit type 'unsigned long'
CPU: 6 PID: 7 Comm: kworker/u16:0 Not tainted 5.15.0-rc3+ #9
Hardware name: Google Lazor (rev3+) with KB Backlight (DT)
Workqueue: events_unbound deferred_probe_work_func
Call trace:
dump_backtrace+0x0/0x170
show_stack+0x24/0x30
dump_stack_lvl+0x64/0x7c
dump_stack+0x18/0x38
ubsan_epilogue+0x10/0x54
__ubsan_handle_shift_out_of_bounds+0x180/0x194
__nvmem_cell_read+0x1ec/0x21c
nvmem_cell_read+0x58/0x94
nvmem_cell_read_variable_common+0x4c/0xb0
nvmem_cell_read_variable_le_u32+0x40/0x100
a6xx_gpu_init+0x170/0x2f4
adreno_bind+0x174/0x284
component_bind_all+0xf0/0x264
msm_drm_bind+0x1d8/0x7a0
try_to_bring_up_master+0x164/0x1ac
__component_add+0xbc/0x13c
component_add+0x20/0x2c
dp_display_probe+0x340/0x384
platform_probe+0xc0/0x100
really_probe+0x110/0x304
__driver_probe_device+0xb8/0x120
driver_probe_device+0x4c/0xfc
__device_attach_driver+0xb0/0x128
bus_for_each_drv+0x90/0xdc
__device_attach+0xc8/0x174
device_initial_probe+0x20/0x2c
bus_probe_device+0x40/0xa4
deferred_probe_work_func+0x7c/0xb8
process_one_work+0x128/0x21c
process_scheduled_works+0x40/0x54
worker_thread+0x1ec/0x2a8
kthread+0x138/0x158
ret_from_fork+0x10/0x20
Fix it by making sure there are any bits to mask out.
Fixes: 69aba7948c ("nvmem: Add a simple NVMEM framework for consumers")
Cc: Douglas Anderson <dianders@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20211013124511.18726-1-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9b7748ffc upstream.
The number of correctable errors is displayed as uncorrectable
errors because the "SBE" error count is passed to both calls of
edac_mc_handle_error().
Pass the correct uncorrectable error count to the second
edac_mc_handle_error() call when logging uncorrectable errors.
[ bp: Massage commit message. ]
Fixes: 7f6998a412 ("ARM: 8888/1: EDAC: Add driver for the Marvell Armada XP SDRAM and L2 cache ECC")
Signed-off-by: Hans Potsch <hans.potsch@nokia.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20211006121332.58788-1-hans.potsch@nokia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f9a174f91 upstream.
The virtio specification virtio-v1.1-cs01 states: "Transitional devices
MUST detect Legacy drivers by detecting that VIRTIO_F_VERSION_1 has not
been acknowledged by the driver." This is exactly what QEMU as of 6.1
has done relying solely on VIRTIO_F_VERSION_1 for detecting that.
However, the specification also says: "... the driver MAY read (but MUST
NOT write) the device-specific configuration fields to check that it can
support the device ..." before setting FEATURES_OK.
In that case, any transitional device relying solely on
VIRTIO_F_VERSION_1 for detecting legacy drivers will return data in
legacy format. In particular, this implies that it is in big endian
format for big endian guests. This naturally confuses the driver which
expects little endian in the modern mode.
It is probably a good idea to amend the spec to clarify that
VIRTIO_F_VERSION_1 can only be relied on after the feature negotiation
is complete. Before validate callback existed, config space was only
read after FEATURES_OK. However, we already have two regressions, so
let's address this here as well.
The regressions affect the VIRTIO_NET_F_MTU feature of virtio-net and
the VIRTIO_BLK_F_BLK_SIZE feature of virtio-blk for BE guests when
virtio 1.0 is used on both sides. The latter renders virtio-blk unusable
with DASD backing, because things simply don't work with the default.
See Fixes tags for relevant commits.
For QEMU, we can work around the issue by writing out the feature bits
with VIRTIO_F_VERSION_1 bit set. We (ab)use the finalize_features
config op for this. This isn't enough to address all vhost devices since
these do not get the features until FEATURES_OK, however it looks like
the affected devices actually never handled the endianness for legacy
mode correctly, so at least that's not a regression.
No devices except virtio net and virtio blk seem to be affected.
Long term the right thing to do is to fix the hypervisors.
Cc: <stable@vger.kernel.org> #v4.11
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Fixes: 82e89ea077 ("virtio-blk: Add validation for block size in config space")
Fixes: fe36cbe067 ("virtio_net: clear MTU when out of range")
Reported-by: markver@us.ibm.com
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Link: https://lore.kernel.org/r/20211011053921.1198936-1-pasic@linux.ibm.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9a470db27 upstream.
fastrpc driver is using find_vma() without any protection, as a
result we see below warning due to recent patch 5b78ed24e8
("mm/pagemap: add mmap_assert_locked() annotations to find_vma*()")
which added mmap_assert_locked() in find_vma() function.
This bug went un-noticed in previous versions. Fix this issue by adding
required protection while calling find_vma().
CPU: 0 PID: 209746 Comm: benchmark_model Not tainted 5.15.0-rc2-00445-ge14fe2bf817a-dirty #969
Hardware name: Qualcomm Technologies, Inc. Robotics RB5 (DT)
pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : find_vma+0x64/0xd0
lr : find_vma+0x60/0xd0
sp : ffff8000158ebc40
...
Call trace:
find_vma+0x64/0xd0
fastrpc_internal_invoke+0x570/0xda8
fastrpc_device_ioctl+0x3e0/0x928
__arm64_sys_ioctl+0xac/0xf0
invoke_syscall+0x44/0x100
el0_svc_common.constprop.3+0x70/0xf8
do_el0_svc+0x24/0x88
el0_svc+0x3c/0x138
el0t_64_sync_handler+0x90/0xb8
el0t_64_sync+0x180/0x184
Fixes: 80f3afd72b ("misc: fastrpc: consider address offset before sending to DSP")
Cc: stable@vger.kernel.org
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210922154326.8927-1-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2115b2b16 upstream.
Commit 7c75bde329 ("usb: musb: musb_dsps: request_irq() after
initializing musb") has inverted the calls to
dsps_setup_optional_vbus_irq() and dsps_create_musb_pdev() without
updating correctly the error path. dsps_create_musb_pdev() allocates and
registers a new platform device which must be unregistered and freed
with platform_device_unregister(), and this is missing upon
dsps_setup_optional_vbus_irq() error.
While on the master branch it seems not to trigger any issue, I observed
a kernel crash because of a NULL pointer dereference with a v5.10.70
stable kernel where the patch mentioned above was backported. With this
kernel version, -EPROBE_DEFER is returned the first time
dsps_setup_optional_vbus_irq() is called which triggers the probe to
error out without unregistering the platform device. Unfortunately, on
the Beagle Bone Black Wireless, the platform device still living in the
system is being used by the USB Ethernet gadget driver, which during the
boot phase triggers the crash.
My limited knowledge of the musb world prevents me to revert this commit
which was sent to silence a robot warning which, as far as I understand,
does not make sense. The goal of this patch was to prevent an IRQ to
fire before the platform device being registered. I think this cannot
ever happen due to the fact that enabling the interrupts is done by the
->enable() callback of the platform musb device, and this platform
device must be already registered in order for the core or any other
user to use this callback.
Hence, I decided to fix the error path, which might prevent future
errors on mainline kernels while also fixing older ones.
Fixes: 7c75bde329 ("usb: musb: musb_dsps: request_irq() after initializing musb")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20211005221631.1529448-1-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 38fa3206bf upstream.
While reboot the system by sysrq, the following bug will be occur.
BUG: sleeping function called from invalid context at kernel/locking/semaphore.c:90
in_atomic(): 0, irqs_disabled(): 128, non_block: 0, pid: 10052, name: rc.shutdown
CPU: 3 PID: 10052 Comm: rc.shutdown Tainted: G W O 5.10.0 #1
Call trace:
dump_backtrace+0x0/0x1c8
show_stack+0x18/0x28
dump_stack+0xd0/0x110
___might_sleep+0x14c/0x160
__might_sleep+0x74/0x88
down_interruptible+0x40/0x118
virt_efi_reset_system+0x3c/0xd0
efi_reboot+0xd4/0x11c
machine_restart+0x60/0x9c
emergency_restart+0x1c/0x2c
sysrq_handle_reboot+0x1c/0x2c
__handle_sysrq+0xd0/0x194
write_sysrq_trigger+0xbc/0xe4
proc_reg_write+0xd4/0xf0
vfs_write+0xa8/0x148
ksys_write+0x6c/0xd8
__arm64_sys_write+0x18/0x28
el0_svc_common.constprop.3+0xe4/0x16c
do_el0_svc+0x1c/0x2c
el0_svc+0x20/0x30
el0_sync_handler+0x80/0x17c
el0_sync+0x158/0x180
The reason for this problem is that irq has been disabled in
machine_restart() and then it calls down_interruptible() in
virt_efi_reset_system(), which would occur sleep in irq context,
it is dangerous! Commit 99409b935c9a("locking/semaphore: Add
might_sleep() to down_*() family") add might_sleep() in
down_interruptible(), so the bug info is here. down_trylock()
can solve this problem, cause there is no might_sleep.
--------
Cc: <stable@vger.kernel.org>
Signed-off-by: Zhang Jianhua <chris.zjh@huawei.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b3a72ca803 upstream.
Joe reports that using a statically allocated buffer for converting CPER
error records into human readable text is probably a bad idea. Even
though we are not aware of any actual issues, a stack buffer is clearly
a better choice here anyway, so let's move the buffer into the stack
frames of the two functions that refer to it.
Cc: <stable@vger.kernel.org>
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42641042c1 upstream.
clang-14 complains about an unusual way of converting a pointer to
an integer:
drivers/misc/cb710/sgbuf2.c:50:15: error: performing pointer subtraction with a null pointer has undefined behavior [-Werror,-Wnull-pointer-subtraction]
return ((ptr - NULL) & 3) != 0;
Replace this with a normal cast to uintptr_t.
Fixes: 5f5bac8272 ("mmc: Driver for CB710/720 memory card reader (MMC part)")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210927121408.939246-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff0e50d356 upstream.
The command ring pointer is located at [6:63] bits of the command
ring control register (CRCR). All the control bits like command stop,
abort are located at [0:3] bits. While aborting a command, we read the
CRCR and set the abort bit and write to the CRCR. The read will always
give command ring pointer as all zeros. So we essentially write only
the control bits. Since we split the 64 bit write into two 32 bit writes,
there is a possibility of xHC command ring stopped before the upper
dword (all zeros) is written. If that happens, xHC updates the upper
dword of its internal command ring pointer with all zeros. Next time,
when the command ring is restarted, we see xHC memory access failures.
Fix this issue by only writing to the lower dword of CRCR where all
control bits are located.
Cc: stable@vger.kernel.org
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211008092547.3996295-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4afb912f43 upstream.
Error injection testing uncovered a case where we'd end up with a
corrupt file system with a missing extent in the middle of a file. This
occurs because the if statement to decide if we should abort is wrong.
The only way we would abort in this case is if we got a ret !=
-EOPNOTSUPP and we called from the file clone code. However the
prealloc code uses this path too. Instead we need to abort if there is
an error, and the only error we _don't_ abort on is -EOPNOTSUPP and only
if we came from the clone file code.
CC: stable@vger.kernel.org # 5.10+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d175209be0 upstream.
I hit a stuck relocation on btrfs/061 during my overnight testing. This
turned out to be because we had left over extent entries in our extent
root for a data reloc inode that no longer existed. This happened
because in btrfs_drop_extents() we only update refs if we have SHAREABLE
set or we are the tree_root. This regression was introduced by
aeb935a455 ("btrfs: don't set SHAREABLE flag for data reloc tree")
where we stopped setting SHAREABLE for the data reloc tree.
The problem here is we actually do want to update extent references for
data extents in the data reloc tree, in fact we only don't want to
update extent references if the file extents are in the log tree.
Update this check to only skip updating references in the case of the
log tree.
This is relatively rare, because you have to be running scrub at the
same time, which is what btrfs/061 does. The data reloc inode has its
extents pre-allocated, and then we copy the extent into the
pre-allocated chunks. We theoretically should never be calling
btrfs_drop_extents() on a data reloc inode. The exception of course is
with scrub, if our pre-allocated extent falls inside of the block group
we are scrubbing, then the block group will be marked read only and we
will be forced to cow that extent. This means we will call
btrfs_drop_extents() on that range when we COW that file extent.
This isn't really problematic if we do this, the data reloc inode
requires that our extent lengths match exactly with the extent we are
copying, thankfully we validate the extent is correct with
get_new_location(), so if we happen to COW only part of the extent we
won't link it in when we do the relocation, so we are safe from any
other shenanigans that arise because of this interaction with scrub.
Fixes: aeb935a455 ("btrfs: don't set SHAREABLE flag for data reloc tree")
CC: stable@vger.kernel.org # 5.8+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cfd312695b upstream.
At replay_one_name(), we are treating any error from btrfs_lookup_inode()
as if the inode does not exists. Fix this by checking for an error and
returning it to the caller.
CC: stable@vger.kernel.org # 4.14+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52db77791f upstream.
At __inode_add_ref(), we treating any error returned from
btrfs_lookup_dir_item() or from btrfs_lookup_dir_index_item() as meaning
that there is no existing directory entry in the fs/subvolume tree.
This is not correct since we can get errors such as, for example, -EIO
when reading extent buffers while searching the fs/subvolume's btree.
So fix that and return the error to the caller when it is not -ENOENT.
CC: stable@vger.kernel.org # 4.14+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e15ac64137 upstream.
At replay_one_one(), we are treating any error returned from
btrfs_lookup_dir_item() or from btrfs_lookup_dir_index_item() as meaning
that there is no existing directory entry in the fs/subvolume tree.
This is not correct since we can get errors such as, for example, -EIO
when reading extent buffers while searching the fs/subvolume's btree.
So fix that and return the error to the caller when it is not -ENOENT.
CC: stable@vger.kernel.org # 4.14+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 171316a68d upstream.
The return type of ktime_divns() is s64. The timeout_to_jiffies() currently
assigns the result of this ktime_divns() to unsigned long, which on 32 bit
systems may overflow. Furthermore, the result of this function is sometimes
also passed to functions which expect signed long, dma_fence_wait_timeout()
is one such example.
Fix this by adjusting the type of remaining_jiffies to s64, so we do not
suffer overflow there, and return a value limited to range of 0..INT_MAX,
which is safe for all usecases of this timeout.
The above overflow can be triggered if userspace passes in too large timeout
value, larger than INT_MAX / HZ seconds. The kernel detects it and complains
about "schedule_timeout: wrong timeout value %lx" and generates a warning
backtrace.
Note that this fixes commit 6cedb8b377 ("drm/msm: avoid using 'timespec'"),
because the previously used timespec_to_jiffies() function returned unsigned
long instead of s64:
static inline unsigned long timespec_to_jiffies(const struct timespec *value)
Fixes: 6cedb8b377 ("drm/msm: avoid using 'timespec'")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jordan Crouse <jcrouse@codeaurora.org>
Cc: Rob Clark <robdclark@chromium.org>
Cc: stable@vger.kernel.org # 5.6+
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210917005913.157379-1-marex@denx.de
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e5809a4dd upstream.
For non-4K PAGE_SIZE configs, the largest gigantic huge page size is
CONT_PMD_SHIFT order. On arm64 with 64K PAGE_SIZE, the gigantic page is
16G. Therefore, one should be able to specify 'hugetlb_cma=16G' on the
kernel command line so that one gigantic page can be allocated from CMA.
However, when adding such an option the following message is produced:
hugetlb_cma: cma area should be at least 8796093022208 MiB
This is because the calculation for non-4K gigantic page order is
incorrect in the arm64 specific routine arm64_hugetlb_cma_reserve().
Fixes: abb7962adc ("arm64/hugetlb: Reserve CMA areas for gigantic pages on 16K and 64K configs")
Cc: <stable@vger.kernel.org> # 5.9.x
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Link: https://lore.kernel.org/r/20211005202529.213812-1-mike.kravetz@oracle.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af89ebaa64 upstream.
gpr_get() return the entire pt_regs (include sr) to userspace, if we
don't restore the C bit in gpr_set, it may break the ALU result in
that context. So the C flag bit is part of gpr context, that's why
riscv totally remove the C bit in the ISA. That makes sr reg clear
from userspace to supervisor privilege.
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fbd63c08cd upstream.
csky restore_sigcontext() blindly overwrites regs->sr with the value
it finds in sigcontext. Attacker can store whatever they want in there,
which includes things like S-bit. Userland shouldn't be able to set
that, or anything other than C flag (bit 0).
Do the same thing other architectures with protected bits in flags
register do - preserve everything that shouldn't be settable in
user mode, picking the rest from the value saved is sigcontext.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Guo Ren <guoren@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit be358af119 upstream.
I received a build failure for a new patch I'm working on the nds32
architecture, and when I went to test it, I couldn't get to my build error,
because it failed to build with a bunch of:
Error: invalid operands (*UND* and *UND* sections) for `^'
issues with various files. Those files were temporary asm files that looked
like: kernel/.tmp_mc_fork.s
I decided to look deeper, and found that the "mc" portion of that name
stood for "mcount", and was created by the recordmcount.pl script. One that
I wrote over a decade ago. Once I knew the source of the problem, I was
able to investigate it further.
The way the recordmcount.pl script works (BTW, there's a C version that
simply modifies the ELF object) is by doing an "objdump" on the object
file. Looks for all the calls to "mcount", and creates an offset of those
locations from some global variable it can use (usually a global function
name, found with <.*>:). Creates a asm file that is a table of references
to these locations, using the found variable/function. Compiles it and
links it back into the original object file. This asm file is called
".tmp_mc_<object_base_name>.s".
The problem here is that the objdump produced by the nds32 object file,
contains things that look like:
0000159a <.L3^B1>:
159a: c6 00 beqz38 $r6, 159a <.L3^B1>
159a: R_NDS32_9_PCREL_RELA .text+0x159e
159c: 84 d2 movi55 $r6, #-14
159e: 80 06 mov55 $r0, $r6
15a0: ec 3c addi10.sp #0x3c
Where ".L3^B1 is somehow selected as the "global" variable to index off of.
Then the assembly file that holds the mcount locations looks like this:
.section __mcount_loc,"a",@progbits
.align 2
.long .L3^B1 + -5522
.long .L3^B1 + -5384
.long .L3^B1 + -5270
.long .L3^B1 + -5098
.long .L3^B1 + -4970
.long .L3^B1 + -4758
.long .L3^B1 + -4122
[...]
And when it is compiled back to an object to link to the original object,
the compile fails on the "^" symbol.
Simple solution for now, is to have the perl script ignore using function
symbols that have an "^" in the name.
Link: https://lkml.kernel.org/r/20211014143507.4ad2c0f7@gandalf.local.home
Cc: stable@vger.kernel.org
Acked-by: Greentime Hu <green.hu@gmail.com>
Fixes: fbf58a52ac ("nds32/ftrace: Add RECORD_MCOUNT support")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a3fd1a986e upstream.
We need to define the codec pin 0x1b to be the mic, but somehow
the mic doesn't support hot plugging detection, and Windows also has
this issue, so we set it to phantom headset-mic.
Also the determine_headset_type() often returns the omtp type by a
mistake when we plug a ctia headset, this makes the mic can't record
sound at all. Because most of the headset are ctia type nowadays and
some machines have the fixed ctia type audio jack, it is possible this
machine has the fixed ctia jack too. Here we set this mic jack to
fixed ctia type, this could avoid the mic type detection mistake and
make the ctia headset work stable.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214537
Reported-and-tested-by: msd <msd.mmq@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20211012114748.5238-1-hui.wang@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd6dd6e3c7 upstream.
This applies a SND_PCI_QUIRK(...) to the TongFang PHxTxX1 barebone. This
fixes the issue of the internal Microphone not working after booting
another OS.
When booting a certain another OS this barebone keeps some coeff settings
even after a cold shutdown. These coeffs prevent the microphone detection
from working in Linux, making the Laptop think that there is always an
external microphone plugged-in and therefore preventing the use of the
internal one.
The relevant indexes and values where gathered by naively diff-ing and
reading a working and a non-working coeff dump.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211006130415.538243-1-wse@tuxedocomputers.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b987fe844 upstream.
The headphone mic is not working on Dell Latitude laptops with ALC3254.
The codec vendor id is 0x10ec0295 and share the same pincfg as defined
in ALC295_STANDARD_PINS. So the ALC269_FIXUP_DELL1_MIC_NO_PRESENCE will
be applied per alc269_pin_fixup_tbl[] but actually the headphone mic is
using NID 0x1b instead of 0x1a. The ALC269_FIXUP_DELL4_MIC_NO_PRESENCE
need to be applied instead.
Use ALC269_FIXUP_DELL4_MIC_NO_PRESENCE for particular models before
a generic fixup comes out.
Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211001062856.1037901-1-chris.chiu@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f8763c59c upstream.
John Keeping reported and posted a patch for a potential UAF in
rawmidi sequencer destruction: the snd_rawmidi_dev_seq_free() may be
called after the associated rawmidi object got already freed.
After a deeper look, it turned out that the bug is rather the
incorrect private_free call order for a snd_seq_device. The
snd_seq_device private_free gets called at the release callback of the
sequencer device object, while this was rather expected to be executed
at the snd_device call chains that runs at the beginning of the whole
card-free procedure. It's been broken since the rewrite of
sequencer-device binding (although it hasn't surfaced because the
sequencer device release happens usually right along with the card
device release).
This patch corrects the private_free call to be done in the right
place, at snd_seq_device_dev_free().
Fixes: 7c37ae5c62 ("ALSA: seq: Rewrite sequencer device binding with standard bus")
Reported-and-tested-by: John Keeping <john@metanate.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210930114114.8645-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 228af5a4fa upstream.
Michael Forney reported an incorrect padding type that was defined in
the commit 80fe7430c7 ("ALSA: add new 32-bit layout for
snd_pcm_mmap_status/control") for PCM control mmap data.
His analysis is correct, and this caused the misplacements of PCM
control data on 32bit arch and 32bit compat mode.
The bug is that the __pad2 definition in __snd_pcm_mmap_control64
struct was wrongly with __pad_before_uframe, which should have been
__pad_after_uframe instead. This struct is used in SYNC_PTR ioctl and
control mmap. Basically this bug leads to two problems:
- The offset of avail_min field becomes wrong, it's placed right after
appl_ptr without padding on little-endian
- When appl_ptr and avail_min are read as 64bit values in kernel side,
the values become either zero or corrupted (mixed up)
One good news is that, because both user-space and kernel
misunderstand the wrong offset, at least, 32bit application running on
32bit kernel works as is. Also, 64bit applications are unaffected
because the padding size is zero. The remaining problem is the 32bit
compat mode; as mentioned in the above, avail_min is placed right
after appl_ptr on little-endian archs, 64bit kernel reads bogus values
for appl_ptr updates, which may lead to streaming bugs like jumping,
XRUN or whatever unexpected.
(However, we haven't heard any serious bug reports due to this over
years, so practically seen, it's fairly safe to assume that the impact
by this bug is limited.)
Ideally speaking, we should correct the wrong mmap status control
definition. But this would cause again incompatibility with the
existing binaries, and fixing it (e.g. by renumbering ioctls) would be
really messy.
So, as of this patch, we only correct the behavior of 32bit compat
mode and keep the rest as is. Namely, the SYNC_PTR ioctl is now
handled differently in compat mode to read/write the 32bit values at
the right offsets. The control mmap of 32bit apps on 64bit kernels
has been already disabled (which is likely rather an overlook, but
this worked fine at this time :), so covering SYNC_PTR ioctl should
suffice as a fallback.
Fixes: 80fe7430c7 ("ALSA: add new 32-bit layout for snd_pcm_mmap_status/control")
Reported-by: Michael Forney <mforney@mforney.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Cc: <stable@vger.kernel.org>
Cc: Rich Felker <dalias@libc.org>
Link: https://lore.kernel.org/r/29QBMJU8DE71E.2YZSH8IHT5HMH@mforney.org
Link: https://lore.kernel.org/r/20211010075546.23220-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The get() method does not understand the on-the-wire encoding of the
remote GPIO states, thinking they are simple on/off bits when they are
really pairs of 16-bit counts. Rewrite the get() handler to return the
value last written, which will eventually match the actual GPIO state
if there are no other changes.
See: https://github.com/raspberrypi/linux/issues/4638
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
[ Upstream commit ebc69e897e ]
This reverts commit 2d52c58b9c.
We have had several folks complain that this causes hangs for them, which
is especially problematic as the commit has also hit stable already.
As no resolution seems to be forthcoming right now, revert the patch.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=214503
Fixes: 2d52c58b9c ("block, bfq: honor already-setup queue merges")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f067d5585c ]
The bytes for max_power_out from the ibm-cffps devices differ in byte
order for some power supplies.
The Witherspoon power supply returns the bytes in MSB/LSB order.
The Rainier power supply returns the bytes in LSB/MSB order.
The Witherspoon power supply uses version cffps1. The Rainier power
supply should use version cffps2. If version is cffps1, swap the bytes
before output to max_power_out.
Tested:
Witherspoon before: 3148. Witherspoon after: 3148.
Rainier before: 53255. Rainier after: 2000.
Signed-off-by: Brandon Wyman <bjwyman@gmail.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20210928205051.1222815-1-bjwyman@gmail.com
[groeck: Replaced yoda programming]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f792565326 ]
Users of rdpmc rely on the mmapped user page to calculate accurate
time_enabled. Currently, userpage->time_enabled is only updated when the
event is added to the pmu. As a result, inactive event (due to counter
multiplexing) does not have accurate userpage->time_enabled. This can
be reproduced with something like:
/* open 20 task perf_event "cycles", to create multiplexing */
fd = perf_event_open(); /* open task perf_event "cycles" */
userpage = mmap(fd); /* use mmap and rdmpc */
while (true) {
time_enabled_mmap = xxx; /* use logic in perf_event_mmap_page */
time_enabled_read = read(fd).time_enabled;
if (time_enabled_mmap > time_enabled_read)
BUG();
}
Fix this by updating userpage for inactive events in merge_sched_in.
Suggested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reported-and-tested-by: Lucian Grijincu <lucian@fb.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20210929194313.2398474-1-songliubraving@fb.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 103bde372f ]
When CONFIG_INET is not set, there are failing references to IPv4
functions, so make this driver depend on INET.
Fixes these build errors:
sparc64-linux-ld: drivers/net/ethernet/sun/sunvnet_common.o: in function `sunvnet_start_xmit_common':
sunvnet_common.c:(.text+0x1a68): undefined reference to `__icmp_send'
sparc64-linux-ld: drivers/net/ethernet/sun/sunvnet_common.o: in function `sunvnet_poll_common':
sunvnet_common.c:(.text+0x358c): undefined reference to `ip_send_check'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Aaron Young <aaron.young@oracle.com>
Cc: Rashmi Narasimhan <rashmi.narasimhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b3b353ef3 ]
Commit 9d682ea6bc ("vboxsf: Fix the check for the old binary
mount-arguments struct") was meant to fix a build error due to sign
mismatch in 'char' and the use of character constants, but it just moved
the error elsewhere, in that on some architectures characters and signed
and on others they are unsigned, and that's just how the C standard
works.
The proper fix is a simple "don't do that then". The code was just
being silly and odd, and it should never have cared about signed vs
unsigned characters in the first place, since what it is testing is not
four "characters", but four bytes.
And the way to compare four bytes is by using "memcmp()".
Which compilers will know to just turn into a single 32-bit compare with
a constant, as long as you don't have crazy debug options enabled.
Link: https://lore.kernel.org/lkml/20210927094123.576521-1-arnd@kernel.org/
Cc: Arnd Bergmann <arnd@kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b193e15ac6 ]
We observed below report when playing with netlink sock:
UBSAN: shift-out-of-bounds in net/sched/sch_api.c:580:10
shift exponent 249 is too large for 32-bit type
CPU: 0 PID: 685 Comm: a.out Not tainted
Call Trace:
dump_stack_lvl+0x8d/0xcf
ubsan_epilogue+0xa/0x4e
__ubsan_handle_shift_out_of_bounds+0x161/0x182
__qdisc_calculate_pkt_len+0xf0/0x190
__dev_queue_xmit+0x2ed/0x15b0
it seems like kernel won't check the stab log value passing from
user, and will use the insane value later to calculate pkt_len.
This patch just add a check on the size/cell_log to avoid insane
calculation.
Reported-by: Abaci <abaci@linux.alibaba.com>
Signed-off-by: Michael Wang <yun.wang@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4bb0bd81ce ]
When we have several pending signals, have entered with the kernel
with large exception frame *and* have already built at least one
sigframe, regs->stkadj is going to be non-zero and regs->format/sr/pc
are going to be junk - the real values are in shifted exception stack
frame we'd built when putting together the first sigframe.
If that happens, subsequent sigframes are going to be garbage.
Not hard to fix - just need to find the "adjusted" frame first
and look for format/vector/sr/pc in it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Finn Thain <fthain@linux-m68k.org>
Link: https://lore.kernel.org/r/YP2dBIAPTaVvHiZ6@zeniv-ca.linux.org.uk
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7970a19b71 ]
The ipv4 and device notifiers are called with RTNL mutex held.
The table walk can take some time, better not block other RTNL users.
'ip a' has been reported to block for up to 20 seconds when conntrack table
has many entries and device down events are frequent (e.g., PPP).
Reported-and-tested-by: Martin Zaharinov <micron10@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30db406923 ]
masq_inet6_event is called asynchronously from system work queue,
because the inet6 notifier is atomic and nf_iterate_cleanup can sleep.
The ipv4 and device notifiers call nf_iterate_cleanup directly.
This is legal, but these notifiers are called with RTNL mutex held.
A large conntrack table with many devices coming and going will have severe
impact on the system usability, with 'ip a' blocking for several seconds.
This change places the defer code into a helper and makes it more
generic so ipv4 and ifdown notifiers can be converted to defer the
cleanup walk as well in a follow patch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a8e1813ff ]
Invoke release_firmware() when the firmware fails to boot in
sof_probe_continue().
The request_firmware() framework must be informed of failures in
sof_probe_continue() otherwise its internal "batching"
feature (different from caching) cached the firmware image
forever. Attempts to correct the file in /lib/firmware/ were then
silently and confusingly ignored until the next reboot. Unloading the
drivers did not help because from their disconnected perspective the
firmware had failed so there was nothing to release.
Also leverage the new snd_sof_fw_unload() function to simplify the
snd_sof_device_remove() function.
Signed-off-by: Marc Herbert <marc.herbert@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20210916085008.28929-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c8fbaa553 ]
Add the new PIDs to wacom_wac.c to support the new models in the Intuos series.
[jkosina@suse.cz: fix changelog]
Signed-off-by: Joshua Dickens <joshua.dickens@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 310e2d43c3 ]
ip6tables only sets the `IP6T_F_PROTO` flag on a rule if a protocol is
specified (`-p tcp`, for example). However, if the flag is not set,
`ip6_packet_match` doesn't call `ipv6_find_hdr` for the skb, in which
case the fragment offset is left uninitialized and a garbage value is
passed to each matcher.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55ce2f649b ]
Current error path of ext4_write_inline_data_end() is not correct.
Firstly, it should pass out the error value if ext4_get_inode_loc()
return fail, or else it could trigger infinite loop if we inject error
here. And then it's better to add inode to orphan list if it return fail
in ext4_journal_stop(), otherwise we could not restore inline xattr
entry after power failure. Finally, we need to reset the 'ret' value if
ext4_write_inline_data_end() return success in ext4_write_end() and
ext4_journalled_write_end(), otherwise we could not get the error return
value of ext4_journal_stop().
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Link: https://lore.kernel.org/r/20210716122024.1105856-3-yi.zhang@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4df031ff58 ]
After commit 3da40c7b08 ("ext4: only call ext4_truncate when size <=
isize"), i_disksize could always be updated to i_size in ext4_setattr(),
and we could sure that i_disksize <= i_size since holding inode lock and
if i_disksize < i_size there are delalloc writes pending in the range
upto i_size. If the end of the current write is <= i_size, there's no
need to touch i_disksize since writeback will push i_disksize upto
i_size eventually. So we can switch to check i_size instead of
i_disksize in ext4_da_write_end() when write to the end of the file.
we also could remove ext4_mark_inode_dirty() together because we defer
inode dirtying to generic_write_end() or ext4_da_write_inline_data_end().
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Link: https://lore.kernel.org/r/20210716122024.1105856-2-yi.zhang@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
In order to resolve a potential startup order bug, the vcio driver has
been rewritten as a platform driver that depends on a DT node for
its instantiation and to locate the firmware driver.
Add that DT node.
See: https://github.com/raspberrypi/linux/issues/4620
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The old vcio driver is a simple character device that manually locates
the firmware driver. Initialising it before the firmware driver causes
a failure, and no retries are attempted.
Rewrite vcio as a platform driver that depends on a DT node for its
instantiation and the location of the firmware driver, making use of
the miscdevice framework to reduce the code size.
N.B. Using miscdevice changes the udev SUBSYSTEM string, so a change
to the companion udev rule is required in order to continue to set
the correct device permissions, e.g.:
KERNEL="vcio", GROUP="video", MODE="0660"
See: https://github.com/raspberrypi/linux/issues/4620
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Power-on reset after the insertion of a battery does not always complete
successfully, leading to corrupted register content. The EXT_TEST bit
will stop the clock from running, but currently the driver will never
recover.
Safely handle the erroneous state by clearing EXT_TEST as part of the
usual set_time method.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Using the rpi_firmware API as intended allows proper reference counting
of the firmware device and means we can remove a downstream patch to
the firmware driver.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Using the rpi_firmware API as intended allows proper reference counting
of the firmware device and means we can remove a downstream patch to
the firmware driver.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
For cases where spare PWM outputs are available, but are desired
to be addressed a standard outputs instead.
Wraps a PWM channel as a new GPIO chip with the one output.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
commit e8f71f8923 upstream.
nvkm test builds fail with the following error.
drivers/gpu/drm/nouveau/nvkm/engine/device/ctrl.c: In function 'nvkm_control_mthd_pstate_info':
drivers/gpu/drm/nouveau/nvkm/engine/device/ctrl.c:60:35: error: overflow in conversion from 'int' to '__s8' {aka 'signed char'} changes value from '-251' to '5'
The code builds on most architectures, but fails on parisc where ENOSYS
is defined as 251.
Replace the error code with -ENODEV (-19). The actual error code does
not really matter and is not passed to userspace - it just has to be
negative.
Fixes: 7238eca4cf ("drm/nouveau: expose pstate selection per-power source in sysfs")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9848417926 ]
The intel powerclamp driver will setup a per-CPU worker with RT
priority. The worker will then invoke play_idle() in which it remains in
the idle poll loop until it is stopped by the timer it started earlier.
That timer needs to expire in hard interrupt context on PREEMPT_RT.
Otherwise the timer will expire in ksoftirqd as a SOFT timer but that task
won't be scheduled on the CPU because its priority is lower than the
priority of the worker which is in the idle loop.
Always expire the idle timer in hard interrupt context.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210906113034.jgfxrjdvxnjqgtmc@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 884f0e84f1 ]
The pending timer has been set up in blk_throtl_init(). However, the
timer is not deleted in blk_throtl_exit(). This means that the timer
handler may still be running after freeing the timer, which would
result in a use-after-free.
Fix by calling del_timer_sync() to delete the timer in blk_throtl_exit().
Signed-off-by: Li Jinlin <lijinlin3@huawei.com>
Link: https://lore.kernel.org/r/20210907121242.2885564-1-lijinlin3@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d44084c934 ]
A consumer is expected to disable a PWM before calling pwm_put(). And if
they didn't there is hopefully a good reason (or the consumer needs
fixing). Also if disabling an enabled PWM was the right thing to do,
this should better be done in the framework instead of in each low level
driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d768cd7fd ]
A consumer is expected to disable a PWM before calling pwm_put(). And if
they didn't there is hopefully a good reason (or the consumer needs
fixing). Also if disabling an enabled PWM was the right thing to do,
this should better be done in the framework instead of in each low level
driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c68eb29c8e ]
A consumer is expected to disable a PWM before calling pwm_put(). And if
they didn't there is hopefully a good reason (or the consumer needs
fixing). Also if disabling an enabled PWM was the right thing to do,
this should better be done in the framework instead of in each low level
driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6c849012b ]
Currently there is no validity check for event ID received from F/W,
Thus exposing driver to memory overrun.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f5dec07ac ]
Patch series "nilfs2: fix incorrect usage of kobject".
This patchset from Nanyong Sun fixes memory leak issues and a NULL
pointer dereference issue caused by incorrect usage of kboject in nilfs2
sysfs implementation.
This patch (of 6):
Reported by syzkaller:
BUG: memory leak
unreferenced object 0xffff888100ca8988 (size 8):
comm "syz-executor.1", pid 1930, jiffies 4294745569 (age 18.052s)
hex dump (first 8 bytes):
6c 6f 6f 70 31 00 ff ff loop1...
backtrace:
kstrdup+0x36/0x70 mm/util.c:60
kstrdup_const+0x35/0x60 mm/util.c:83
kvasprintf_const+0xf1/0x180 lib/kasprintf.c:48
kobject_set_name_vargs+0x56/0x150 lib/kobject.c:289
kobject_add_varg lib/kobject.c:384 [inline]
kobject_init_and_add+0xc9/0x150 lib/kobject.c:473
nilfs_sysfs_create_device_group+0x150/0x7d0 fs/nilfs2/sysfs.c:986
init_nilfs+0xa21/0xea0 fs/nilfs2/the_nilfs.c:637
nilfs_fill_super fs/nilfs2/super.c:1046 [inline]
nilfs_mount+0x7b4/0xe80 fs/nilfs2/super.c:1316
legacy_get_tree+0x105/0x210 fs/fs_context.c:592
vfs_get_tree+0x8e/0x2d0 fs/super.c:1498
do_new_mount fs/namespace.c:2905 [inline]
path_mount+0xf9b/0x1990 fs/namespace.c:3235
do_mount+0xea/0x100 fs/namespace.c:3248
__do_sys_mount fs/namespace.c:3456 [inline]
__se_sys_mount fs/namespace.c:3433 [inline]
__x64_sys_mount+0x14b/0x1f0 fs/namespace.c:3433
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3b/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
If kobject_init_and_add return with error, then the cleanup of kobject
is needed because memory may be allocated in kobject_init_and_add
without freeing.
And the place of cleanup_dev_kobject should use kobject_put to free the
memory associated with the kobject. As the section "Kobject removal" of
"Documentation/core-api/kobject.rst" says, kobject_del() just makes the
kobject "invisible", but it is not cleaned up. And no more cleanup will
do after cleanup_dev_kobject, so kobject_put is needed here.
Link: https://lkml.kernel.org/r/1625651306-10829-1-git-send-email-konishi.ryusuke@gmail.com
Link: https://lkml.kernel.org/r/1625651306-10829-2-git-send-email-konishi.ryusuke@gmail.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Link: https://lkml.kernel.org/r/20210629022556.3985106-2-sunnanyong@huawei.com
Signed-off-by: Nanyong Sun <sunnanyong@huawei.com>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f96a5bfa1 ]
We update the ctime/mtime of a block device when we remove it so that
blkid knows the device changed. However we do this by re-opening the
block device and calling filp_update_time. This is more correct because
it'll call the inode->i_op->update_time if it exists, but the block dev
inodes do not do this. Instead call generic_update_time() on the
bd_inode in order to avoid the blkdev_open path and get rid of the
following lockdep splat:
======================================================
WARNING: possible circular locking dependency detected
5.14.0-rc2+ #406 Not tainted
------------------------------------------------------
losetup/11596 is trying to acquire lock:
ffff939640d2f538 ((wq_completion)loop0){+.+.}-{0:0}, at: flush_workqueue+0x67/0x5e0
but task is already holding lock:
ffff939655510c68 (&lo->lo_mutex){+.+.}-{3:3}, at: __loop_clr_fd+0x41/0x660 [loop]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #4 (&lo->lo_mutex){+.+.}-{3:3}:
__mutex_lock+0x7d/0x750
lo_open+0x28/0x60 [loop]
blkdev_get_whole+0x25/0xf0
blkdev_get_by_dev.part.0+0x168/0x3c0
blkdev_open+0xd2/0xe0
do_dentry_open+0x161/0x390
path_openat+0x3cc/0xa20
do_filp_open+0x96/0x120
do_sys_openat2+0x7b/0x130
__x64_sys_openat+0x46/0x70
do_syscall_64+0x38/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
-> #3 (&disk->open_mutex){+.+.}-{3:3}:
__mutex_lock+0x7d/0x750
blkdev_get_by_dev.part.0+0x56/0x3c0
blkdev_open+0xd2/0xe0
do_dentry_open+0x161/0x390
path_openat+0x3cc/0xa20
do_filp_open+0x96/0x120
file_open_name+0xc7/0x170
filp_open+0x2c/0x50
btrfs_scratch_superblocks.part.0+0x10f/0x170
btrfs_rm_device.cold+0xe8/0xed
btrfs_ioctl+0x2a31/0x2e70
__x64_sys_ioctl+0x80/0xb0
do_syscall_64+0x38/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
-> #2 (sb_writers#12){.+.+}-{0:0}:
lo_write_bvec+0xc2/0x240 [loop]
loop_process_work+0x238/0xd00 [loop]
process_one_work+0x26b/0x560
worker_thread+0x55/0x3c0
kthread+0x140/0x160
ret_from_fork+0x1f/0x30
-> #1 ((work_completion)(&lo->rootcg_work)){+.+.}-{0:0}:
process_one_work+0x245/0x560
worker_thread+0x55/0x3c0
kthread+0x140/0x160
ret_from_fork+0x1f/0x30
-> #0 ((wq_completion)loop0){+.+.}-{0:0}:
__lock_acquire+0x10ea/0x1d90
lock_acquire+0xb5/0x2b0
flush_workqueue+0x91/0x5e0
drain_workqueue+0xa0/0x110
destroy_workqueue+0x36/0x250
__loop_clr_fd+0x9a/0x660 [loop]
block_ioctl+0x3f/0x50
__x64_sys_ioctl+0x80/0xb0
do_syscall_64+0x38/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
other info that might help us debug this:
Chain exists of:
(wq_completion)loop0 --> &disk->open_mutex --> &lo->lo_mutex
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&lo->lo_mutex);
lock(&disk->open_mutex);
lock(&lo->lo_mutex);
lock((wq_completion)loop0);
*** DEADLOCK ***
1 lock held by losetup/11596:
#0: ffff939655510c68 (&lo->lo_mutex){+.+.}-{3:3}, at: __loop_clr_fd+0x41/0x660 [loop]
stack backtrace:
CPU: 1 PID: 11596 Comm: losetup Not tainted 5.14.0-rc2+ #406
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.13.0-2.fc32 04/01/2014
Call Trace:
dump_stack_lvl+0x57/0x72
check_noncircular+0xcf/0xf0
? stack_trace_save+0x3b/0x50
__lock_acquire+0x10ea/0x1d90
lock_acquire+0xb5/0x2b0
? flush_workqueue+0x67/0x5e0
? lockdep_init_map_type+0x47/0x220
flush_workqueue+0x91/0x5e0
? flush_workqueue+0x67/0x5e0
? verify_cpu+0xf0/0x100
drain_workqueue+0xa0/0x110
destroy_workqueue+0x36/0x250
__loop_clr_fd+0x9a/0x660 [loop]
? blkdev_ioctl+0x8d/0x2a0
block_ioctl+0x3f/0x50
__x64_sys_ioctl+0x80/0xb0
do_syscall_64+0x38/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6d37ccdd2 ]
capsnaps will take inode references via ihold when queueing to flush.
When force unmounting, the client will just close the sessions and
may never get a flush reply, causing a leak and inode ref leak.
Fix this by removing the capsnaps for an inode when removing the caps.
URL: https://tracker.ceph.com/issues/52295
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b11ed50346 ]
The current code will update the mtime and then try to get caps to
handle the write. If we end up having to request caps from the MDS, then
the mtime in the cap grant will clobber the updated mtime and it'll be
lost.
This is most noticable when two clients are alternately writing to the
same file. Fw caps are continually being granted and revoked, and the
mtime ends up stuck because the updated mtimes are always being
overwritten with the old one.
Fix this by changing the order of operations in ceph_write_iter to get
the caps before updating the times. Also, make sure we check the pool
full conditions before even getting any caps or uninlining.
URL: https://tracker.ceph.com/issues/46574
Reported-by: Jozef Kováč <kovac@firma.zoznam.sk>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Luis Henriques <lhenriques@suse.de>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aac6c0f907 ]
The xilinx dma driver uses the consistent allocations, so for correct
operation also set the DMA mask for coherent APIs. It fixes the below
kernel crash with dmatest client when DMA IP is configured with 64-bit
address width and linux is booted from high (>4GB) memory.
Call trace:
[ 489.531257] dma_alloc_from_pool+0x8c/0x1c0
[ 489.535431] dma_direct_alloc+0x284/0x330
[ 489.539432] dma_alloc_attrs+0x80/0xf0
[ 489.543174] dma_pool_alloc+0x160/0x2c0
[ 489.547003] xilinx_cdma_prep_memcpy+0xa4/0x180
[ 489.551524] dmatest_func+0x3cc/0x114c
[ 489.555266] kthread+0x124/0x130
[ 489.558486] ret_from_fork+0x10/0x3c
[ 489.562051] ---[ end trace 248625b2d596a90a ]---
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Reviewed-by: Harini Katakam <harini.katakam@xilinx.com>
Link: https://lore.kernel.org/r/1629363528-30347-1-git-send-email-radhey.shyam.pandey@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3811a50ad ]
Currently, iommu_init_ga() checks and disables IOMMU VAPIC support
(i.e. AMD AVIC support in IOMMU) when GAMSup feature bit is not set.
However it forgets to clear IRQ_POSTING_CAP from the previously set
amd_iommu_irq_ops.capability.
This triggers an invalid page fault bug during guest VM warm reboot
if AVIC is enabled since the irq_remapping_cap(IRQ_POSTING_CAP) is
incorrectly set, and crash the system with the following kernel trace.
BUG: unable to handle page fault for address: 0000000000400dd8
RIP: 0010:amd_iommu_deactivate_guest_mode+0x19/0xbc
Call Trace:
svm_set_pi_irte_mode+0x8a/0xc0 [kvm_amd]
? kvm_make_all_cpus_request_except+0x50/0x70 [kvm]
kvm_request_apicv_update+0x10c/0x150 [kvm]
svm_toggle_avic_for_irq_window+0x52/0x90 [kvm_amd]
svm_enable_irq_window+0x26/0xa0 [kvm_amd]
vcpu_enter_guest+0xbbe/0x1560 [kvm]
? avic_vcpu_load+0xd5/0x120 [kvm_amd]
? kvm_arch_vcpu_load+0x76/0x240 [kvm]
? svm_get_segment_base+0xa/0x10 [kvm_amd]
kvm_arch_vcpu_ioctl_run+0x103/0x590 [kvm]
kvm_vcpu_ioctl+0x22a/0x5d0 [kvm]
__x64_sys_ioctl+0x84/0xc0
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xae
Fixes by moving the initializing of AMD IOMMU interrupt remapping mode
(amd_iommu_guest_ir) earlier before setting up the
amd_iommu_irq_ops.capability with appropriate IRQ_POSTING_CAP flag.
[joro: Squashed the two patches and limited
check_features_on_all_iommus() to CONFIG_IRQ_REMAP
to fix a compile warning.]
Signed-off-by: Wei Huang <wei.huang2@amd.com>
Co-developed-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Link: https://lore.kernel.org/r/20210820202957.187572-2-suravee.suthikulpanit@amd.com
Link: https://lore.kernel.org/r/20210820202957.187572-3-suravee.suthikulpanit@amd.com
Fixes: 8bda0cfbdc ("iommu/amd: Detect and initialize guest vAPIC log")
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 907872baa9 ]
parisc build test images fail to compile with the following error.
drivers/parisc/dino.c:160:12: error:
'pci_dev_is_behind_card_dino' defined but not used
Move the function just ahead of its only caller to avoid the error.
Fixes: 5fa1659105 ("parisc: Disable HP HSC-PCI Cards to prevent kernel crash")
Cc: Helge Deller <deller@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b92d4add5 ]
DEFINE_SMP_CALL_CACHE_FUNCTION() was usefel before the CPU hotplug rework
to ensure that the cache related functions are called on the upcoming CPU
because the notifier itself could run on any online CPU.
The hotplug state machine guarantees that the callbacks are invoked on the
upcoming CPU. So there is no need to have this SMP function call
obfuscation. That indirection was missed when the hotplug notifiers were
converted.
This also solves the problem of ARM64 init_cache_level() invoking ACPI
functions which take a semaphore in that context. That's invalid as SMP
function calls run with interrupts disabled. Running it just from the
callback in context of the CPU hotplug thread solves this.
Fixes: 8571890e15 ("arm64: Add support for ACPI based firmware tables")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Will Deacon <will@kernel.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/871r69ersb.ffs@tglx
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3dc549986 ]
Due to high latency in PCIE clock switching on RKL platforms,
switching the PCIE clock dynamically at runtime can lead to HDMI/DP
audio problems. On newer asics this is handled in the SMU firmware.
For SMU7-based asics, disable PCIE clock switching to avoid the issue.
AMD provide a parameter to disable PICE_DPM.
modprobe amdgpu ppfeaturemask=0xfff7bffb
It's better to contorl PCIE_DPM in amd gpu driver,
switch PCI_DPM by determining intel RKL platform for SMU7-based asics.
Fixes: 1a31474cdb ("drm/amd/pm: workaround for audio noise issue")
Ref: https://lists.freedesktop.org/archives/amd-gfx/2021-August/067413.html
Signed-off-by: Koba Ko <koba.ko@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb83610762 ]
There are two pairs of declarations for thermal_cooling_device_register()
and thermal_of_cooling_device_register(), and only one set was changed
in a recent patch, so the other one now causes a compile-time warning:
drivers/net/wireless/mediatek/mt76/mt7915/init.c: In function 'mt7915_thermal_init':
drivers/net/wireless/mediatek/mt76/mt7915/init.c:134:48: error: passing argument 1 of 'thermal_cooling_device_register' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
134 | cdev = thermal_cooling_device_register(wiphy_name(wiphy), phy,
| ^~~~~~~~~~~~~~~~~
In file included from drivers/net/wireless/mediatek/mt76/mt7915/init.c:7:
include/linux/thermal.h:407:39: note: expected 'char *' but argument is of type 'const char *'
407 | thermal_cooling_device_register(char *type, void *devdata,
| ~~~~~~^~~~
Change the dummy helper functions to have the same arguments as the
normal version.
Fixes: f991de53a8 ("thermal: make device_register's type argument const")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210722090717.1116748-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4002173b7 ]
The first thing metric_delayed_work does is check mdsc->stopping,
and then return immediately if it's set. That's good since we would
have already torn down the metric structures at this point, otherwise,
but there is no locking around mdsc->stopping.
It's possible that the ceph_metric_destroy call could race with the
delayed_work, in which case we could end up with the delayed_work
accessing destroyed percpu variables.
At this point in the mdsc teardown, the "stopping" flag has already been
set, so there's no benefit to flushing the work. Move the work
cancellation in ceph_metric_destroy ahead of the percpu variable
destruction, and eliminate the flush_delayed_work call in
ceph_mdsc_destroy.
Fixes: 18f473b384 ("ceph: periodically send perf metrics to MDSes")
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Xiubo Li <xiubli@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d453ceb654 ]
Add trace event to report samples and their timestamp coming from the
EC. It allows to check if the timestamps are correct and the filter is
working correctly without introducing too much latency.
To enable these events:
cd /sys/kernel/debug/tracing/
echo 1 > events/cros_ec/enable
echo 0 > events/cros_ec/cros_ec_request_start/enable
echo 0 > events/cros_ec/cros_ec_request_done/enable
echo 1 > tracing_on
cat trace_pipe
Observe event flowing:
irq/105-chromeo-95 [000] .... 613.659758: cros_ec_sensorhub_timestamp: ...
irq/105-chromeo-95 [000] .... 613.665219: cros_ec_sensorhub_filter: dx: ...
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 020162d6f4 upstream.
This fixes a race condition: After pwmchip_add() is called there might
already be a consumer and then modifying the hardware behind the
consumer's back is bad. So reset before calling pwmchip_add().
Note that reseting the hardware isn't the right thing to do if the PWM
is already running as it might e.g. disable (or even enable) a backlight
that is supposed to be on (or off).
Fixes: 4dce82c1e8 ("pwm: add pwm-mxs support")
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d2813fb17 upstream.
This fixes a race condition: After pwmchip_add() is called there might
already be a consumer and then modifying the hardware behind the
consumer's back is bad. So set the default before.
(Side-note: I don't know what this register setting actually does, if
this modifies the polarity there is an inconsistency because the
inversed polarity isn't considered if the PWM is already running during
.probe().)
Fixes: acfd92fdfb ("pwm: lpc32xx: Set PWM_PIN_LEVEL bit to default value")
Cc: Sylvain Lemieux <slemieux@tycoint.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a9344cd0a upstream.
There are variables(power.may_skip_resume and dev->power.must_resume)
and DPM_FLAG_MAY_SKIP_RESUME flags to control the resume of devices after
a system wide suspend transition.
Setting the DPM_FLAG_MAY_SKIP_RESUME flag means that the driver allows
its "noirq" and "early" resume callbacks to be skipped if the device
can be left in suspend after a system-wide transition into the working
state. PM core determines that the driver's "noirq" and "early" resume
callbacks should be skipped or not with dev_pm_skip_resume() function by
checking power.may_skip_resume variable.
power.must_resume variable is getting set to false in __device_suspend()
function without checking device's DPM_FLAG_MAY_SKIP_RESUME settings.
In problematic scenario, where all the devices in the suspend_late
stage are successful and some device can fail to suspend in
suspend_noirq phase. So some devices successfully suspended in suspend_late
stage are not getting chance to execute __device_suspend_noirq()
to set dev->power.must_resume variable to true and not getting
resumed in early_resume phase.
Add a check for device's DPM_FLAG_MAY_SKIP_RESUME flag before
setting power.must_resume variable in __device_suspend function.
Fixes: 6e176bf8d4 ("PM: sleep: core: Do not skip callbacks in the resume phase")
Signed-off-by: Prasad Sodagudi <psodagud@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98e2e409e7 upstream.
When the refcount is decreased to 0, the resource reclamation branch is
entered. Before CPU0 reaches the race point (1), CPU1 may obtain the
spinlock and traverse the rbtree to find 'root', see
nilfs_lookup_root().
Although CPU1 will call refcount_inc() to increase the refcount, it is
obviously too late. CPU0 will release 'root' directly, CPU1 then
accesses 'root' and triggers UAF.
Use refcount_dec_and_lock() to ensure that both the operations of
decrease refcount to 0 and link deletion are lock protected eliminates
this risk.
CPU0 CPU1
nilfs_put_root():
<-------- (1)
spin_lock(&nilfs->ns_cptree_lock);
rb_erase(&root->rb_node, &nilfs->ns_cptree);
spin_unlock(&nilfs->ns_cptree_lock);
kfree(root);
<-------- use-after-free
refcount_t: underflow; use-after-free.
WARNING: CPU: 2 PID: 9476 at lib/refcount.c:28 \
refcount_warn_saturate+0x1cf/0x210 lib/refcount.c:28
Modules linked in:
CPU: 2 PID: 9476 Comm: syz-executor.0 Not tainted 5.10.45-rc1+ #3
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), ...
RIP: 0010:refcount_warn_saturate+0x1cf/0x210 lib/refcount.c:28
... ...
Call Trace:
__refcount_sub_and_test include/linux/refcount.h:283 [inline]
__refcount_dec_and_test include/linux/refcount.h:315 [inline]
refcount_dec_and_test include/linux/refcount.h:333 [inline]
nilfs_put_root+0xc1/0xd0 fs/nilfs2/the_nilfs.c:795
nilfs_segctor_destroy fs/nilfs2/segment.c:2749 [inline]
nilfs_detach_log_writer+0x3fa/0x570 fs/nilfs2/segment.c:2812
nilfs_put_super+0x2f/0xf0 fs/nilfs2/super.c:467
generic_shutdown_super+0xcd/0x1f0 fs/super.c:464
kill_block_super+0x4a/0x90 fs/super.c:1446
deactivate_locked_super+0x6a/0xb0 fs/super.c:335
deactivate_super+0x85/0x90 fs/super.c:366
cleanup_mnt+0x277/0x2e0 fs/namespace.c:1118
__cleanup_mnt+0x15/0x20 fs/namespace.c:1125
task_work_run+0x8e/0x110 kernel/task_work.c:151
tracehook_notify_resume include/linux/tracehook.h:188 [inline]
exit_to_user_mode_loop kernel/entry/common.c:164 [inline]
exit_to_user_mode_prepare+0x13c/0x170 kernel/entry/common.c:191
syscall_exit_to_user_mode+0x16/0x30 kernel/entry/common.c:266
do_syscall_64+0x45/0x80 arch/x86/entry/common.c:56
entry_SYSCALL_64_after_hwframe+0x44/0xa9
There is no reproduction program, and the above is only theoretical
analysis.
Link: https://lkml.kernel.org/r/1629859428-5906-1-git-send-email-konishi.ryusuke@gmail.com
Fixes: ba65ae4729 ("nilfs2: add checkpoint tree to nilfs object")
Link: https://lkml.kernel.org/r/20210723012317.4146-1-thunder.leizhen@huawei.com
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e1fbbd0731 upstream.
Keno Fischer reported that when a binray loaded via ld-linux-x the
prctl(PR_SET_MM_MAP) doesn't allow to setup brk value because it lays
before mm:end_data.
For example a test program shows
| # ~/t
|
| start_code 401000
| end_code 401a15
| start_stack 7ffce4577dd0
| start_data 403e10
| end_data 40408c
| start_brk b5b000
| sbrk(0) b5b000
and when executed via ld-linux
| # /lib64/ld-linux-x86-64.so.2 ~/t
|
| start_code 7fc25b0a4000
| end_code 7fc25b0c4524
| start_stack 7fffcc6b2400
| start_data 7fc25b0ce4c0
| end_data 7fc25b0cff98
| start_brk 55555710c000
| sbrk(0) 55555710c000
This of course prevent criu from restoring such programs. Looking into
how kernel operates with brk/start_brk inside brk() syscall I don't see
any problem if we allow to setup brk/start_brk without checking for
end_data. Even if someone pass some weird address here on a purpose then
the worst possible result will be an unexpected unmapping of existing vma
(own vma, since prctl works with the callers memory) but test for
RLIMIT_DATA is still valid and a user won't be able to gain more memory in
case of expanding VMAs via new values shipped with prctl call.
Link: https://lkml.kernel.org/r/20210121221207.GB2174@grain
Fixes: bbdc6076d2 ("binfmt_elf: move brk out of mmap when doing direct loader exec")
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Reported-by: Keno Fischer <keno@juliacomputing.com>
Acked-by: Andrey Vagin <avagin@gmail.com>
Tested-by: Andrey Vagin <avagin@gmail.com>
Cc: Dmitry Safonov <0x7f454c46@gmail.com>
Cc: Kirill Tkhai <ktkhai@virtuozzo.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Cc: Alexander Mikhalitsyn <alexander.mikhalitsyn@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a86d41404 upstream.
Currently perf saves a build-id with size but old versions assumes the
size of 20. In case the build-id is less than 20 (like for MD5), it'd
fill the rest with 0s.
I saw a problem when old version of perf record saved a binary in the
build-id cache and new version of perf reads the data. The symbols
should be read from the build-id cache (as the path no longer has the
same binary) but it failed due to mismatch in the build-id.
symsrc__init: build id mismatch for /home/namhyung/.debug/.build-id/53/e4c2f42a4c61a2d632d92a72afa08f00000000/elf.
The build-id event in the data has 20 byte build-ids, but it saw a
different size (16) when it reads the build-id of the elf file in the
build-id cache.
$ readelf -n ~/.debug/.build-id/53/e4c2f42a4c61a2d632d92a72afa08f00000000/elf
Displaying notes found in: .note.gnu.build-id
Owner Data size Description
GNU 0x00000010 NT_GNU_BUILD_ID (unique build ID bitstring)
Build ID: 53e4c2f42a4c61a2d632d92a72afa08f
Let's fix this by allowing trailing zeros if the size is different.
Fixes: 39be8d0115 ("perf tools: Pass build_id object to dso__build_id_equal()")
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20210910224630.1084877-1-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 099ec97ac9 upstream.
clang warns:
drivers/staging/rtl8192u/r8192U_core.c:4268:20: warning: bitwise and of
boolean expressions; did you mean logical and? [-Wbool-operation-and]
bpacket_toself = bpacket_match_bssid &
^~~~~~~~~~~~~~~~~~~~~
&&
1 warning generated.
Replace the bitwise AND with a logical one to clear up the warning, as
that is clearly what was intended.
Fixes: 8fc8598e61 ("Staging: Added Realtek rtl8192u driver to staging")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20210814235625.1780033-1-nathan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef6c8d6ccf upstream.
When SCTP handles an INIT chunk, it calls for example:
sctp_sf_do_5_1B_init
sctp_verify_init
sctp_verify_param
sctp_process_init
sctp_process_param
handling of SCTP_PARAM_SET_PRIMARY
sctp_verify_init() wasn't doing proper size validation and neither the
later handling, allowing it to work over the chunk itself, possibly being
uninitialized memory.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6ffe7671b upstream.
In one of the fallbacks that SCTP has for identifying an association for an
incoming packet, it looks for AddIp chunk (from ASCONF) and take a peek.
Thing is, at this stage nothing was validating that the chunk actually had
enough content for that, allowing the peek to happen over uninitialized
memory.
Similar check already exists in actual asconf handling in
sctp_verify_asconf().
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fcf044891c upstream.
We do not need a SWIOTLB unless we have DRAM that is addressable beyond
the arm_dma_limit. Compare max_pfn with arm_dma_pfn_limit to determine
whether we do need a SWIOTLB to be initialized.
Fixes: ad3c7b18c5 ("arm: use swiotlb for bounce buffering on LPAE configs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8b92b8c1e upstream.
We should not walk/touch page tables outside of VMA boundaries when
holding only the mmap sem in read mode. Evil user space can modify the
VMA layout just before this function runs and e.g., trigger races with
page table removal code since commit dd2283f260 ("mm: mmap: zap pages
with read mmap_sem in munmap").
find_vma() does not check if the address is >= the VMA start address;
use vma_lookup() instead.
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Fixes: dd2283f260 ("mm: mmap: zap pages with read mmap_sem in munmap")
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a2b2eb556 upstream.
The Linux console's VT102 implementation already consumes OSC
("Operating System Command") sequences, probably because that's how
palette changes are transmitted.
In addition to OSC, there are three other major clases of ANSI control
strings: APC ("Application Program Command"), PM ("Privacy Message"),
and DCS ("Device Control String"). They are handled similarly to OSC in
terms of termination.
Source: vt100.net
Add three new enumerated states, one for each of these types. All three
are handled the same way right now--they simply consume input until
terminated. I hope to expand upon this firmament in the future. Add
new predicate ansi_control_string(), returning true for any of these
states. Replace explicit checks against ESosc with calls to this
function. Transition to these states appropriately from the escape
initiation (ESesc) state.
This was motivated by the following Notcurses bugs:
https://github.com/dankamongmen/notcurses/issues/2050https://github.com/dankamongmen/notcurses/issues/1828https://github.com/dankamongmen/notcurses/issues/2069
where standard VT sequences are not consumed by the Linux console. It's
not necessary that the Linux console *support* these sequences, but it
ought *consume* these well-specified classes of sequences.
Tested by sending a variety of escape sequences to the console, and
verifying that they still worked, or were now properly consumed.
Verified that the escapes were properly terminated at a generic level.
Verified that the Notcurses tools continued to show expected output on
the Linux console, except now without escape bleedthrough.
Link: https://lore.kernel.org/lkml/YSydL0q8iaUfkphg@schwarzgerat.orthanc/
Signed-off-by: nick black <dankamongmen@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 02319bf15a upstream.
After d12e1c4649 ("net: dsa: b53: Set correct number of ports in the
DSA struct") we stopped setting dsa_switch::num_ports to DSA_MAX_PORTS,
which created an off by one error between the statically allocated
bcm_sf2_priv::port_sts array (of size DSA_MAX_PORTS). When
dsa_is_cpu_port() is used, we end-up accessing an out of bounds member
and causing a NPD.
Fix this by iterating with the appropriate port count using
ds->num_ports.
Fixes: d12e1c4649 ("net: dsa: b53: Set correct number of ports in the DSA struct")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eca4cf12ac upstream.
The recent patch has introduced a regression by not reading the reset
count in the ERROR_RECOVERY async event handler. We may have just
gone through a reset and the reset count has just incremented. If
we don't update the reset count in the ERROR_RECOVERY event handler,
the health check timer will see that the reset count has changed and
will initiate an unintended reset.
Restore the unconditional update of the reset count in
bnxt_async_event_process() if error recovery watchdog is enabled.
Also, update the reset count at the end of the reset sequence to
make it even more robust.
Fixes: 1b2b918319 ("bnxt_en: Fix possible unintended driver initiated error recovery")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81065b35e2 upstream.
There are two cases for machine check recovery:
1) The machine check was triggered by ring3 (application) code.
This is the simpler case. The machine check handler simply queues
work to be executed on return to user. That code unmaps the page
from all users and arranges to send a SIGBUS to the task that
triggered the poison.
2) The machine check was triggered in kernel code that is covered by
an exception table entry. In this case the machine check handler
still queues a work entry to unmap the page, etc. but this will
not be called right away because the #MC handler returns to the
fix up code address in the exception table entry.
Problems occur if the kernel triggers another machine check before the
return to user processes the first queued work item.
Specifically, the work is queued using the ->mce_kill_me callback
structure in the task struct for the current thread. Attempting to queue
a second work item using this same callback results in a loop in the
linked list of work functions to call. So when the kernel does return to
user, it enters an infinite loop processing the same entry for ever.
There are some legitimate scenarios where the kernel may take a second
machine check before returning to the user.
1) Some code (e.g. futex) first tries a get_user() with page faults
disabled. If this fails, the code retries with page faults enabled
expecting that this will resolve the page fault.
2) Copy from user code retries a copy in byte-at-time mode to check
whether any additional bytes can be copied.
On the other side of the fence are some bad drivers that do not check
the return value from individual get_user() calls and may access
multiple user addresses without noticing that some/all calls have
failed.
Fix by adding a counter (current->mce_count) to keep track of repeated
machine checks before task_work() is called. First machine check saves
the address information and calls task_work_add(). Subsequent machine
checks before that task_work call back is executed check that the address
is in the same page as the first machine check (since the callback will
offline exactly one page).
Expected worst case is four machine checks before moving on (e.g. one
user access with page faults disabled, then a repeat to the same address
with page faults enabled ... repeat in copy tail bytes). Just in case
there is some code that loops forever enforce a limit of 10.
[ bp: Massage commit message, drop noinstr, fix typo, extend panic
messages. ]
Fixes: 5567d11c21 ("x86/mce: Send #MC singal from task work")
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/YT/IJ9ziLqmtqEPu@agluck-desk2.amr.corp.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0341d5e3d1 ]
The cur_tx counter must be incremented after TACT bit of
txdesc->status was set. However, a CPU is possible to reorder
instructions and/or memory accesses between cur_tx and
txdesc->status. And then, if TX interrupt happened at such a
timing, the sh_eth_tx_free() may free the descriptor wrongly.
So, add wmb() before cur_tx++.
Otherwise NETDEV WATCHDOG timeout is possible to happen.
Fixes: 86a74ff21a ("net: sh_eth: add support for Renesas SuperH Ethernet")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdff1eda69 ]
One MIPS platform (mach-rc32434) defines GPIOBASE. This macro
conflicts with one of the same name in lpc_sch.c. Rename the latter one
to prevent the build error.
../drivers/mfd/lpc_sch.c:25: error: "GPIOBASE" redefined [-Werror]
25 | #define GPIOBASE 0x44
../arch/mips/include/asm/mach-rc32434/rb.h:32: note: this is the location of the previous definition
32 | #define GPIOBASE 0x050000
Cc: Denis Turischev <denis@compulab.co.il>
Fixes: e82c60ae7d ("mfd: Introduce lpc_sch for Intel SCH LPC bridge")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 922e8ce883 ]
The IRQ support for SCH GPIO is not specific to the Intel Quark SoC.
Moreover the IRQ routing is quite interesting there, so while it's
needs a special support, the driver haven't it anyway yet.
Due to above remove basically redundant code of IRQ support.
This reverts commit ec689a8a81.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b2b918319 ]
If error recovery is already enabled, bnxt_timer() will periodically
check the heartbeat register and the reset counter. If we get an
error recovery async. notification from the firmware (e.g. change in
primary/secondary role), we will immediately read and update the
heartbeat register and the reset counter. If the timer for the next
health check expires soon after this, we may read the heartbeat register
again in quick succession and find that it hasn't changed. This will
trigger error recovery unintentionally.
The likelihood is small because we also reset fw_health->tmr_counter
which will reset the interval for the next health check. But the
update is not protected and bnxt_timer() can miss the update and
perform the health check without waiting for the full interval.
Fix it by only reading the heartbeat register and reset counter in
bnxt_async_event_process() if error recovery is trasitioning to the
enabled state. Also add proper memory barriers so that when enabling
for the first time, bnxt_timer() will see the tmr_counter interval and
perform the health check after the full interval has elapsed.
Fixes: 7e914027f7 ("bnxt_en: Enable health monitoring.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4d95c3c19 ]
We currently only log the error recovery settings if it is enabled.
In some cases, firmware disables error recovery after it was
initially enabled. Without logging anything, the user will not be
aware of this change in setting.
Log it when error recovery is disabled. Also, change the reset count
value from hexadecimal to decimal.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a44daa8fcb ]
Firmware is capable of generating asynchronous debug notifications.
The event data is opaque to the driver and is simply logged. Debug
notifications can be enabled by turning on hardware status messages
using the ethtool msglvl interface.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6fdab8a3ad ]
The current asic.rev is incomplete and does not include the metal
revision. Add the metal revision and decode the complete asic
revision into the more common and readable form (A0, B0, etc).
Fixes: 7154917a12 ("bnxt_en: Refactor bnxt_dl_info_get().")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63f8428b40 ]
Broadcom's b53 switches have one IMP (Inband Management Port) that needs
to be programmed using its own designed register. IMP port may be
different than CPU port - especially on devices with multiple CPU ports.
For that reason it's required to explicitly note IMP port index and
check for it when choosing a register to use.
This commit fixes BCM5301x support. Those switches use CPU port 5 while
their IMP port is 8. Before this patch b53 was trying to program port 5
with B53_PORT_OVERRIDE_CTRL instead of B53_GMII_PORT_OVERRIDE_CTRL(5).
It may be possible to also replace "cpu_port" usages with
dsa_is_cpu_port() but that is out of the scope of thix BCM5301x fix.
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a0ed250f9 ]
The GRE tunnel device can pull existing outer headers in ipge_xmit.
This is a rare path, apparently unique to this device. The below
commit ensured that pulling does not move skb->data beyond csum_start.
But it has a false positive if ip_summed is not CHECKSUM_PARTIAL and
thus csum_start is irrelevant.
Refine to exclude this. At the same time simplify and strengthen the
test.
Simplify, by moving the check next to the offending pull, making it
more self documenting and removing an unnecessary branch from other
code paths.
Strengthen, by also ensuring that the transport header is correct and
therefore the inner headers will be after skb_reset_inner_headers.
The transport header is set to csum_start in skb_partial_csum_set.
Link: https://lore.kernel.org/netdev/YS+h%2FtqCJJiQei+W@shredder/
Fixes: 1d011c4803 ("ip_gre: add validation for csum_start")
Reported-by: Ido Schimmel <idosch@idosch.org>
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ddbc2a00d ]
Previous commit 68233c583a removes the qlcnic_rom_lock()
in qlcnic_pinit_from_rom(), but remains its corresponding
unlock function, which is odd. I'm not very sure whether the
lock is missing, or the unlock is redundant. This bug is
suggested by a static analysis tool, please advise.
Fixes: 68233c583a ("qlcnic: updated reset sequence")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7c5e6ff53 ]
syzbot found that forcing a big quantum attribute would crash hosts fast,
essentially using this:
tc qd replace dev eth0 root fq_codel quantum 4294967295
This is because fq_codel_dequeue() would have to loop
~2^31 times in :
if (flow->deficit <= 0) {
flow->deficit += q->quantum;
list_move_tail(&flow->flowchain, &q->old_flows);
goto begin;
}
SFQ max quantum is 2^19 (half a megabyte)
Lets adopt a max quantum of one megabyte for FQ_CODEL.
Fixes: 4b549a2ef4 ("fq_codel: Fair Queue Codel AQM")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 730affed24 ]
Bug reported by KASAN:
BUG: KASAN: use-after-scope in inet6_ehashfn (net/ipv6/inet6_hashtables.c:40)
Call Trace:
(...)
inet6_ehashfn (net/ipv6/inet6_hashtables.c:40)
(...)
nf_sk_lookup_slow_v6 (net/ipv6/netfilter/nf_socket_ipv6.c:91
net/ipv6/netfilter/nf_socket_ipv6.c:146)
It seems that this bug has already been fixed by Eric Dumazet in the
past in:
commit 78296c97ca ("netfilter: xt_socket: fix a stack corruption bug")
But a variant of the same issue has been introduced in
commit d64d80a2cd ("netfilter: x_tables: don't extract flow keys on early demuxed sks in socket match")
`daddr` and `saddr` potentially hold a reference to ipv6_var that is no
longer in scope when the call to `nf_socket_get_sock_v6` is made.
Fixes: d64d80a2cd ("netfilter: x_tables: don't extract flow keys on early demuxed sks in socket match")
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Benjamin Hesmans <benjamin.hesmans@tessares.net>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d12e1c4649 ]
Setting DSA_MAX_PORTS caused DSA to call b53 callbacks (e.g.
b53_disable_port() during dsa_register_switch()) for invalid
(non-existent) ports. That made b53 modify unrelated registers and is
one of reasons for a broken BCM5301x support.
This problem exists for years but DSA_MAX_PORTS usage has changed few
times. It seems the most accurate to reference commit dropping
dsa_switch_alloc() in the Fixes tag.
Fixes: 7e99e34701 ("net: dsa: remove dsa_switch_alloc helper")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdb067d31c ]
It isn't true that CPU port is always the last one. Switches BCM5301x
have 9 ports (port 6 being inactive) and they use port 5 as CPU by
default (depending on design some other may be CPU ports too).
A more reliable way of determining number of ports is to check for the
last set bit in the "enabled_ports" bitfield.
This fixes b53 internal state, it will allow providing accurate info to
the DSA and is required to fix BCM5301x support.
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ecdc28defc ]
If the network devices connected to the system beyond
HSO_MAX_NET_DEVICES. add_net_device() in hso_create_net_device()
will be failed for the network_table is full. It will lead to
business failure which rely on network_table, for example,
hso_suspend() and hso_resume(). It will also lead to memory leak
because resource release process can not search the hso_device
object from network_table in hso_free_interface().
Add failure handler for add_net_device() in hso_create_net_device()
to solve the above problems.
Fixes: 72dc1c096c ("HSO: add option hso driver")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfd862a7e9 ]
'$cin' and '$sin' variables are local to a function: they are then not
available from the cleanup trap.
Instead, we need to use '$large' and '$small' that are not local and
defined just before setting the trap.
Without this patch, running this script in a loop might cause a:
write: No space left on device
issue.
Fixes: 1a418cb8e8 ("mptcp: simult flow self-tests")
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e90dfa7a8 ]
I noticed that only port 0 worked on the RTL8366RB since we
started to use custom tags.
It turns out that the format of egress custom tags is actually
different from ingress custom tags. While the lower bits just
contain the port number in ingress tags, egress tags need to
indicate destination port by setting the bit for the
corresponding port.
It was working on port 0 because port 0 added 0x00 as port
number in the lower bits, and if you do this the packet appears
at all ports, including the intended port. Ooops.
Fix this and all ports work again. Use the define for shifting
the "type A" into place while we're at it.
Tested on the D-Link DIR-685 by sending traffic to each of
the ports in turn. It works.
Fixes: 86dd9868b8 ("net: dsa: tag_rtl4_a: Support also egress tags")
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 889a1b3f35 ]
If an error occurs after a 'gpiochip_add_data()' call it must be undone by
a corresponding 'gpiochip_remove()' as already done in the remove function.
To simplify the code a fix a leak in the error handling path of the probe,
use the managed version instead (i.e. 'devm_gpiochip_add_data()')
Fixes: 698b8eeaed ("gpio/mpc8xxx: change irq handler from chained to normal")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 555bda42b0 ]
Commit 698b8eeaed ("gpio/mpc8xxx: change irq handler from chained to normal")
has introduced a new 'goto err;' at the very end of the function, but has
not updated the error handling path accordingly.
Add the now missing 'irq_domain_remove()' call which balances a previous
'irq_domain_create_linear() call.
Fixes: 698b8eeaed ("gpio/mpc8xxx: change irq handler from chained to normal")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit edf7b4a2d8 ]
The build on fedora:35 and fedora:rawhide with clang is failing with:
49 41.00 fedora:35 : FAIL clang version 13.0.0 (Fedora 13.0.0~rc1-1.fc35)
bench/inject-buildid.c:351:6: error: variable 'len' set but not used [-Werror,-Wunused-but-set-variable]
u64 len = 0;
^
1 error generated.
make[3]: *** [/git/perf-5.14.0-rc7/tools/build/Makefile.build:139: bench] Error 2
50 41.11 fedora:rawhide : FAIL clang version 13.0.0 (Fedora 13.0.0~rc1-1.fc35)
bench/inject-buildid.c:351:6: error: variable 'len' set but not used [-Werror,-Wunused-but-set-variable]
u64 len = 0;
^
1 error generated.
make[3]: *** [/git/perf-5.14.0-rc7/tools/build/Makefile.build:139: bench] Error 2
That 'len' variable is not used at all, so just make sure all the
synthesize_RECORD() routines return ssize_t to propagate the writen()
return, as it may fail, ditch the 'ret' var and bail out if those
routines fail.
Fixes: 0bf02a0d80 ("perf bench: Add build-id injection benchmark")
Acked-by: Namhyung Kim <namhyung@kernel.org>
Link: http://lore.kernel.org/lkml/CAM9d7cgEZNSor+B+7Y2C+QYGme_v5aH0Zn0RLfxoQ+Fy83EHrg@mail.gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b5ff0405e ]
0day bot reports a build error:
ERROR: modpost: "clear_user_page" [drivers/media/v4l2-core/videobuf-dma-sg.ko] undefined!
so export it in arch/arc/ to fix the build error.
In most ARCHes, clear_user_page() is a macro. OTOH, in a few
ARCHes it is a function and needs to be exported.
PowerPC exported it in 2004. It looks like nds32 and nios2
still need to have it exported.
Fixes: 4102b53392 ("ARC: [mm] Aliasing VIPT dcache support 2/4")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-snps-arc@lists.infradead.org
Signed-off-by: Vineet Gupta <vgupta@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6826c6849b ]
The CPU_ON PSCI call takes a payload that KVM uses to configure a
destination vCPU to run. This payload is non-architectural state and not
exposed through any existing UAPI. Effectively, we have a race between
CPU_ON and userspace saving/restoring a guest: if the target vCPU isn't
ran again before the VMM saves its state, the requested PC and context
ID are lost. When restored, the target vCPU will be runnable and start
executing at its old PC.
We can avoid this race by making sure the reset payload is serviced
before userspace can access a vCPU's state.
Fixes: 358b28f09f ("arm/arm64: KVM: Allow a VCPU to fully reset itself")
Signed-off-by: Oliver Upton <oupton@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210818202133.1106786-3-oupton@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6654f9dfcb ]
KVM correctly serializes writes to a vCPU's reset state, however since
we do not take the KVM lock on the read side it is entirely possible to
read state from two different reset requests.
Cure the race for now by taking the KVM lock when reading the
reset_state structure.
Fixes: 358b28f09f ("arm/arm64: KVM: Allow a VCPU to fully reset itself")
Signed-off-by: Oliver Upton <oupton@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210818202133.1106786-2-oupton@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a89d69a44e ]
Since 2431c4f5b4 ("mtd: Implement mtd_{read,write}() as wrappers
around mtd_{read,write}_oob()") don't allow _write|_read and
_write_oob|_read_oob existing at the same time, we should check the
existence of callbacks "_read and _write" from subdev's master device
(We can trust master device since it has been registered) before
assigning, otherwise following warning occurs while making
concatenated device:
WARNING: CPU: 2 PID: 6728 at drivers/mtd/mtdcore.c:595
add_mtd_device+0x7f/0x7b0
Fixes: 2431c4f5b4 ("mtd: Implement mtd_{read,write}() around ...")
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210817114857.2784825-3-chengzhihao1@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a946506c48 ]
The driver was registering IRQ 0 when no IRQ was set. This leads to
warnings with newer kernels.
Clear the resource flags, so no resource is registered at all in this
case.
Fixes: 2f17dd34ff ("mfd: tqmx86: IO controller with I2C, Wachdog and GPIO")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3245a7b7b ]
Syzbot hit use-after-free in nf_tables_dump_sets. The problem was in
missing lock protection for nft_ct_pcpu_template_refcnt.
Before commit f102d66b33 ("netfilter: nf_tables: use dedicated
mutex to guard transactions") all transactions were serialized by global
mutex, but then global mutex was changed to local per netnamespace
commit_mutex.
This change causes use-after-free bug, when 2 netnamespaces concurently
changing nft_ct_pcpu_template_refcnt without proper locking. Fix it by
adding nft_ct_pcpu_mutex and protect all nft_ct_pcpu_template_refcnt
changes with it.
Fixes: f102d66b33 ("netfilter: nf_tables: use dedicated mutex to guard transactions")
Reported-and-tested-by: syzbot+649e339fa6658ee623d3@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit daa3736151 ]
Remove interrupt disablement during backlight setting. It is
way to dangerous and makes platforms instable by having it
miss vblank IRQs leading to the graphics derailing.
The code is using ndelay() which is not available on
platforms such as ARM and will result in 32 * udelay(1)
which is substantial.
Add some code to detect if an interrupt occurs during the
tight loop and in that case just redo it from the top.
Fixes: 5317f37e48 ("backlight: Add Kinetic KTD253 backlight driver")
Cc: Stephan Gerhold <stephan@gerhold.net>
Reported-by: newbyte@disroot.org
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f949a9ebce ]
On Cherry Trail devices with an AXP288 PMIC the external SD-card slot
used the AXP's DLDO2 as card-voltage and either DLDO3 or GPIO1LDO
(GPIO1 pin in low noise LDO mode) as signal-voltage.
These regulators are turned on/off and in case of the signal-voltage
also have their output-voltage changed by the _PS0 and _PS3 power-
management ACPI methods on the MMC-controllers ACPI fwnode as well as
by the _DSM ACPI method for changing the signal voltage.
The AML code implementing these methods is directly accessing the
PMIC through ACPI I2C OpRegion accesses, instead of using the special
PMIC OpRegion handled by drivers/acpi/pmic/intel_pmic_xpower.c .
This means that the contents of the involved PMIC registers can change
without the change being made through the regmap interface, so regmap
should not cache the contents of these registers.
Mark the regulator power on/off, the regulator voltage control and the
GPIO1 control registers as volatile, to avoid regmap caching them.
Specifically this fixes an issue on some models where the i915 driver
toggles another LDO using the same on/off register on/off through
MIPI sequences (through intel_soc_pmic_exec_mipi_pmic_seq_element())
which then writes back a cached on/off register-value where the
card-voltage is off causing the external sdcard slot to stop working
when the screen goes blank, or comes back on again.
The regulator register-range now marked volatile also includes the
buck regulator control registers. This is done on purpose these are
normally not touched by the AML code, but they are updated directly
by the SoC's PUNIT which means that they may also change without going
through regmap.
Note the AXP288 PMIC is only used on Bay- and Cherry-Trail platforms,
so even though this is an ACPI specific problem there is no need to
make the new volatile ranges conditional since these platforms always
use ACPI.
Fixes: dc91c3b6fe ("mfd: axp20x: Mark AXP20X_VBUS_IPSOUT_MGMT as volatile")
Fixes: cd53216625 ("mfd: axp20x: Fix axp288 volatile ranges")
Reported-and-tested-by: Clamshell <clamfly@163.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1511df6f5e upstream.
EMIT6_PCREL() macro assumes that the previous pass generated 6 bytes
of code, which is not the case if branch shortening took place. Fix by
using jit->prg, like all the other EMIT6_PCREL_*() macros.
Reported-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Fixes: 4e9b4a6883 ("s390/bpf: Use relative long branches")
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e61dc9da0 upstream.
The JIT uses agfi for subtracting constants, but -(-0x80000000) cannot
be represented as a 32-bit signed binary integer. Fix by using algfi in
this particular case.
Reported-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Fixes: 0546231057 ("s390/bpf: Add s390x eBPF JIT compiler backend")
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db7bee6538 upstream.
Currently the JIT completely removes things like `reg32 += 0`,
however, the BPF_ALU semantics requires the target register to be
zero-extended in such cases.
Fix by optimizing out only the arithmetic operation, but not the
subsequent zero-extension.
Reported-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Fixes: 0546231057 ("s390/bpf: Add s390x eBPF JIT compiler backend")
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0097ae5f7a ]
When the function IS_ALIGNED() returns false, the value of ret is 0.
So, we set ret to -EINVAL to indicate this error.
Clean up smatch warning:
drivers/ntb/test/ntb_perf.c:602 perf_setup_inbuf() warn: missing error
code 'ret'.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 319f83ac98 ]
When the value of nm->isr_ctx is false, the value of ret is 0.
So, we set ret to -ENOMEM to indicate this error.
Clean up smatch warning:
drivers/ntb/test/ntb_msi_test.c:373 ntb_msit_probe() warn: missing
error code 'ret'.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7db8263a12 ]
When adapter->registered_device_map is NULL, the value of err is
uncertain, we set err to -EINVAL to avoid ambiguity.
Clean up smatch warning:
drivers/net/ethernet/chelsio/cxgb/cxgb2.c:1114 init_one() warn: missing
error code 'err'
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d52c58b9c ]
The function bfq_setup_merge prepares the merging between two
bfq_queues, say bfqq and new_bfqq. To this goal, it assigns
bfqq->new_bfqq = new_bfqq. Then, each time some I/O for bfqq arrives,
the process that generated that I/O is disassociated from bfqq and
associated with new_bfqq (merging is actually a redirection). In this
respect, bfq_setup_merge increases new_bfqq->ref in advance, adding
the number of processes that are expected to be associated with
new_bfqq.
Unfortunately, the stable-merging mechanism interferes with this
setup. After bfqq->new_bfqq has been set by bfq_setup_merge, and
before all the expected processes have been associated with
bfqq->new_bfqq, bfqq may happen to be stably merged with a different
queue than the current bfqq->new_bfqq. In this case, bfqq->new_bfqq
gets changed. So, some of the processes that have been already
accounted for in the ref counter of the previous new_bfqq will not be
associated with that queue. This creates an unbalance, because those
references will never be decremented.
This commit fixes this issue by reestablishing the previous, natural
behaviour: once bfqq->new_bfqq has been set, it will not be changed
until all expected redirections have occurred.
Signed-off-by: Davide Zini <davidezini2@gmail.com>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Link: https://lore.kernel.org/r/20210802141352.74353-2-paolo.valente@linaro.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aabbdc67f3 ]
Add quirk CDC_MBIM_FLAG_AVOID_ALTSETTING_TOGGLE for Telit LN920
0x1061 composition in order to avoid bind error.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21274aa178 ]
Check one more time before exiting the API with an error.
Fix API to poll at least twice, in case there are other high priority
tasks and this API doesn't get CPU cycles for multiple jiffies update.
In addition, increase timeout from usecs_to_jiffies(10000) to
usecs_to_jiffies(20000), to prevent the case that for CONFIG_100HZ
timeout will be a single jiffies.
A single jiffies results actual timeout that can be any time between
1usec and 10msec. To solve this, a value of usecs_to_jiffies(20000)
ensures that timeout is 2 jiffies.
Signed-off-by: Smadar Fuks <smadarf@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dbe80cf471 ]
We must not pet a running watchdog when handle_boot_enabled is off
because this will kick off automatic triggering before userland is
running, defeating the purpose of the handle_boot_enabled control.
Furthermore, don't ping in case watchdog_set_last_hw_keepalive was
called incorrectly when the hardware watchdog is actually not running.
Fixed: cef9572e9a ("watchdog: add support for adjusting last known HW keepalive time")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/93d56386-6e37-060b-55ce-84de8cde535f@web.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 32837d8a8f ]
Some Cavium endpoints are implemented as multi-function devices without ACS
capability, but they actually don't support peer-to-peer transactions.
Add ACS quirks to declare DMA isolation for the following devices:
- BGX device found on Octeon-TX (8xxx)
- CGX device found on Octeon-TX2 (9xxx)
- RPM device found on Octeon-TX3 (10xxx)
Link: https://lore.kernel.org/r/20210810122425.1115156-1-george.cherian@marvell.com
Signed-off-by: George Cherian <george.cherian@marvell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1de58802f ]
J7200 has the same PCIe IP as in J721E with minor changes in the
wrapper. J7200 allows byte access of bridge configuration space
registers and the register field for LINK_DOWN interrupt is different.
J7200 also requires "quirk_detect_quiet_flag" to be set. Configure these
changes as part of driver data applicable only to J7200.
Link: https://lore.kernel.org/r/20210811123336.31357-4-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09c24094b2 ]
PCIe fails to link up if SERDES lanes not used by PCIe are assigned to
another protocol. For example, link training fails if lanes 2 and 3 are
assigned to another protocol while lanes 0 and 1 are used for PCIe to
form a two lane link. This failure is due to an incorrect tie-off on an
internal status signal indicating electrical idle.
Status signals going from SERDES to PCIe Controller are tied-off when a
lane is not assigned to PCIe. Signal indicating electrical idle is
incorrectly tied-off to a state that indicates non-idle. As a result,
PCIe sees unused lanes to be out of electrical idle and this causes
LTSSM to exit Detect.Quiet state without waiting for 12ms timeout to
occur. If a receiver is not detected on the first receiver detection
attempt in Detect.Active state, LTSSM goes back to Detect.Quiet and
again moves forward to Detect.Active state without waiting for 12ms as
required by PCIe base specification. Since wait time in Detect.Quiet is
skipped, multiple receiver detect operations are performed back-to-back
without allowing time for capacitance on the transmit lines to
discharge. This causes subsequent receiver detection to always fail even
if a receiver gets connected eventually.
Add a quirk flag "quirk_detect_quiet_flag" to program the minimum
time the LTSSM should wait on entering Detect.Quiet state here.
This has to be set for J7200 as it has an incorrect tie-off on unused
lanes.
Link: https://lore.kernel.org/r/20210811123336.31357-3-kishon@ti.com
Signed-off-by: Nadeem Athani <nadeem@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e242060c6 ]
Since kprobe_events and uprobe_events only check whether the
other same-type probe event has the same name or not, if the
user gives the same name of the existing tracepoint event (or
the other type of probe events), it silently fails to create
the tracefs entry (but registered.) as below.
/sys/kernel/tracing # ls events/task/task_rename
enable filter format hist id trigger
/sys/kernel/tracing # echo p:task/task_rename vfs_read >> kprobe_events
[ 113.048508] Could not create tracefs 'task_rename' directory
/sys/kernel/tracing # cat kprobe_events
p:task/task_rename vfs_read
To fix this issue, check whether the existing events have the
same name or not in trace_probe_register_event_call(). If exists,
it rejects to register the new event.
Link: https://lkml.kernel.org/r/162936876189.187130.17558311387542061930.stgit@devnote2
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ff80e2de3 ]
Although irq_create_mapping() is able to deal with duplicate
mappings, it really isn't supposed to be a substitute for
irq_find_mapping(), and can result in allocations that take place
in atomic context if the mapping didn't exist.
Fix the handful of MFD drivers that use irq_create_mapping() in
interrupt context by using irq_find_mapping() instead.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1e71c1688 ]
There is a potential race between fuse_read_interrupt() and
fuse_request_end().
TASK1
in fuse_read_interrupt(): delete req->intr_entry (while holding
fiq->lock)
TASK2
in fuse_request_end(): req->intr_entry is empty -> skip fiq->lock
wake up TASK3
TASK3
request is freed
TASK1
in fuse_read_interrupt(): dereference req->in.h.unique ***BAM***
Fix by always grabbing fiq->lock if the request was ever interrupted
(FR_INTERRUPTED set) thereby serializing with concurrent
fuse_read_interrupt() calls.
FR_INTERRUPTED is set before the request is queued on fiq->interrupts.
Dequeing the request is done with list_del_init() but FR_INTERRUPTED is not
cleared in this case.
Reported-by: lijiazi <lijiazi@xiaomi.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec343111c0 ]
These are the actual frequencies reported by the PLL, so let's
report these. The roundoffs are inappropriate, we should round
to the frequency that the clock will later report.
Drop some whitespace at the same time.
Cc: phone-devel@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 427900d27d upstream.
Currently, the VF does not clear the interrupt source immediately after
receiving the interrupt. As a result, if the second interrupt task is
triggered when processing the first interrupt task, clearing the
interrupt source before exiting will clear the interrupt sources of the
two tasks at the same time. As a result, no interrupt is triggered for
the second task. The VF detects the missed message only when the next
interrupt is generated.
Clearing it immediately after executing check_evt_cause ensures that:
1. Even if two interrupt tasks are triggered at the same time, they can
be processed.
2. If the second task is triggered during the processing of the first
task and the interrupt source is not cleared, the interrupt is reported
after vector0 is enabled.
Fixes: b90fcc5bd9 ("net: hns3: add reset handling for VF when doing Core/Global/IMP reset")
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b81d894874 upstream.
The firmware will not disable mac in flr process. Therefore, the driver
needs to proactively disable mac during flr, which is the same as the
function reset.
Fixes: 35d93a3004 ("net: hns3: adjust the process of PF reset")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1dc839ec09 upstream.
Currently, affinity_mask is set to a single cpu. As a result,
irqbalance becomes invalid in SUBSET or EXACT mode. To solve
this problem, change affinity_mask to numa node range. In this
way, irqbalance can be performed on the cpu of the numa node.
Fixes: 0812545487 ("net: hns3: add interrupt affinity support for misc interrupt")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d18e81183b upstream.
The hardware cannot handle short tunnel frames below 65 bytes,
and will cause vlan tag missing problem. So pads packet size to
65 bytes for tunnel frames to fix this bug.
Fixes: 3db084d28dc0("net: hns3: Fix for vxlan tx checksum bug")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1affc01fdc upstream.
The call to bnxt_free_mem(..., false) in the bnxt_half_open_nic() error
path will deallocate ring descriptor memory via bnxt_free_?x_rings(),
but because irq_re_init is false, the ring info itself is not freed.
To simplify error paths, deallocation functions have generally been
written to be safe when called on unallocated memory. It should always
be safe to call dev_close(), which calls bnxt_free_skbs() a second time,
even in this semi- allocated ring state.
Calling bnxt_free_skbs() a second time with the rings already freed will
cause NULL pointer dereference. Fix it by checking the rings are valid
before proceeding in bnxt_free_tx_skbs() and
bnxt_free_one_rx_ring_skbs().
Fixes: 975bc99a4a ("bnxt_en: Refactor bnxt_free_rx_skbs().")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 267cdfa213 upstream.
POWER9 DD2.2 and 2.3 hardware implements a "fake-suspend" mode where
certain TM instructions executed in HV=0 mode cause softpatch interrupts
so the hypervisor can emulate them and prevent problematic processor
conditions. In this fake-suspend mode, the treclaim. instruction does
not modify registers.
Unfortunately the rfscv instruction executed by the guest do not
generate softpatch interrupts, which can cause the hypervisor to lose
track of the fake-suspend mode, and it can execute this treclaim. while
not in fake-suspend mode. This modifies GPRs and crashes the hypervisor.
It's not trivial to disable scv in the guest with HFSCR now, because
they assume a POWER9 has scv available. So this fix saves and restores
checkpointed registers across the treclaim.
Fixes: 7854f7545b ("KVM: PPC: Book3S: Rework TM save/restore code and make it C-callable")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210908101718.118522-2-npiggin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 273c29e944 upstream.
If a failover occurs before a login response is received, the login
response buffer maybe undefined. Check that there was no failover
before accessing the login response buffer.
Fixes: 032c5e8284 ("Driver for IBM System i/p VNIC protocol")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e50e711351 upstream.
Turn udp_tunnel_nic work-queue to an ordered work-queue. This queue
holds the UDP-tunnel configuration commands of the different netdevs.
When the netdevs are functions of the same NIC the order of
execution may be crucial.
Problem example:
NIC with 2 PFs, both PFs declare offload quota of up to 3 UDP-ports.
$ifconfig eth2 1.1.1.1/16 up
$ip link add eth2_19503 type vxlan id 5049 remote 1.1.1.2 dev eth2 dstport 19053
$ip link set dev eth2_19503 up
$ip link add eth2_19504 type vxlan id 5049 remote 1.1.1.3 dev eth2 dstport 19054
$ip link set dev eth2_19504 up
$ip link add eth2_19505 type vxlan id 5049 remote 1.1.1.4 dev eth2 dstport 19055
$ip link set dev eth2_19505 up
$ip link add eth2_19506 type vxlan id 5049 remote 1.1.1.5 dev eth2 dstport 19056
$ip link set dev eth2_19506 up
NIC RX port offload infrastructure offloads the first 3 UDP-ports (on
all devices which sets NETIF_F_RX_UDP_TUNNEL_PORT feature) and not
UDP-port 19056. So both PFs gets this offload configuration.
$ip link set dev eth2_19504 down
This triggers udp-tunnel-core to remove the UDP-port 19504 from
offload-ports-list and offload UDP-port 19056 instead.
In this scenario it is important that the UDP-port of 19504 will be
removed from both PFs before trying to add UDP-port 19056. The NIC can
stop offloading a UDP-port only when all references are removed.
Otherwise the NIC may report exceeding of the offload quota.
Fixes: cc4e3835ef ("udp_tunnel: add central NIC RX port offload infrastructure")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 20e100f527 upstream.
Handle MFW (management FW) error response in order to avoid a crash
during recovery flows.
Changes from v1:
- Add "Fixes tag".
Fixes: tag 5e7ba042fd ("qed: Fix reading stale configuration information")
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b704b27be upstream.
If altname deletion of the short alternative name fails, the error
message printed is: "Failed to add short alternative name".
This is obviously a typo, as we are testing altname deletion.
Fix this using a proper error message.
Fixes: f95e6c9c46 ("selftest: net: add alternative names test")
Signed-off-by: Andrea Claudi <aclaudi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f884f3962 upstream.
Commit 10d3be5692 ("tcp-tso: do not split TSO packets at retransmit
time") may directly retrans a multiple segments TSO/GSO packet without
split, Since this commit, we can no longer assume that a retransmitted
packet is a single segment.
This patch fixes the tp->undo_retrans accounting in tcp_sacktag_one()
that use the actual segments(pcount) of the retransmitted packet.
Before that commit (10d3be5692), the assumption underlying the
tp->undo_retrans-- seems correct.
Fixes: 10d3be5692 ("tcp-tso: do not split TSO packets at retransmit time")
Signed-off-by: zhenggy <zhenggy@chinatelecom.cn>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a69ae291e1 upstream.
Commit 865c50e1d2 ("x86/uaccess: utilize CONFIG_CC_HAS_ASM_GOTO_OUTPUT")
added an optimised version of __get_user_asm() for x86 using 'asm goto'.
Like the non-optimised code, the 32-bit implementation of 64-bit
get_user() expands to a pair of 32-bit accesses. Unlike the
non-optimised code, the _original_ pointer is incremented to copy the
high word instead of loading through a new pointer explicitly
constructed to point at a 32-bit type. Consequently, if the pointer
points at a 64-bit type then we end up loading the wrong data for the
upper 32-bits.
This was observed as a mount() failure in Android targeting i686 after
b0cfcdd9b9 ("d_path: make 'prepend()' fill up the buffer exactly on
overflow") because the call to copy_from_kernel_nofault() from
prepend_copy() ends up in __get_kernel_nofault() and casts the source
pointer to a 'u64 __user *'. An attempt to mount at "/debug_ramdisk"
therefore ends up failing trying to mount "/debumdismdisk".
Use the existing '__gu_ptr' source pointer to unsigned int for 32-bit
__get_user_asm_u64() instead of the original pointer.
Cc: Bill Wendling <morbo@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 865c50e1d2 ("x86/uaccess: utilize CONFIG_CC_HAS_ASM_GOTO_OUTPUT")
Signed-off-by: Will Deacon <will@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6a52e73368 upstream.
DSA supports connecting to a phy-handle, and has a fallback to a non-OF
based method of connecting to an internal PHY on the switch's own MDIO
bus, if no phy-handle and no fixed-link nodes were present.
The -ENODEV error code from the first attempt (phylink_of_phy_connect)
is what triggers the second attempt (phylink_connect_phy).
However, when the first attempt returns a different error code than
-ENODEV, this results in an unbalance of calls to phylink_create and
phylink_destroy by the time we exit the function. The phylink instance
has leaked.
There are many other error codes that can be returned by
phylink_of_phy_connect. For example, phylink_validate returns -EINVAL.
So this is a practical issue too.
Fixes: aab9c4067d ("net: dsa: Plug in PHYLINK support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20210914134331.2303380-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04f08eb44b upstream.
syzbot reported another data-race in af_unix [1]
Lets change __skb_insert() to use WRITE_ONCE() when changing
skb head qlen.
Also, change unix_dgram_poll() to use lockless version
of unix_recvq_full()
It is verry possible we can switch all/most unix_recvq_full()
to the lockless version, this will be done in a future kernel version.
[1] HEAD commit: 8596e589b7
BUG: KCSAN: data-race in skb_queue_tail / unix_dgram_poll
write to 0xffff88814eeb24e0 of 4 bytes by task 25815 on cpu 0:
__skb_insert include/linux/skbuff.h:1938 [inline]
__skb_queue_before include/linux/skbuff.h:2043 [inline]
__skb_queue_tail include/linux/skbuff.h:2076 [inline]
skb_queue_tail+0x80/0xa0 net/core/skbuff.c:3264
unix_dgram_sendmsg+0xff2/0x1600 net/unix/af_unix.c:1850
sock_sendmsg_nosec net/socket.c:703 [inline]
sock_sendmsg net/socket.c:723 [inline]
____sys_sendmsg+0x360/0x4d0 net/socket.c:2392
___sys_sendmsg net/socket.c:2446 [inline]
__sys_sendmmsg+0x315/0x4b0 net/socket.c:2532
__do_sys_sendmmsg net/socket.c:2561 [inline]
__se_sys_sendmmsg net/socket.c:2558 [inline]
__x64_sys_sendmmsg+0x53/0x60 net/socket.c:2558
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffff88814eeb24e0 of 4 bytes by task 25834 on cpu 1:
skb_queue_len include/linux/skbuff.h:1869 [inline]
unix_recvq_full net/unix/af_unix.c:194 [inline]
unix_dgram_poll+0x2bc/0x3e0 net/unix/af_unix.c:2777
sock_poll+0x23e/0x260 net/socket.c:1288
vfs_poll include/linux/poll.h:90 [inline]
ep_item_poll fs/eventpoll.c:846 [inline]
ep_send_events fs/eventpoll.c:1683 [inline]
ep_poll fs/eventpoll.c:1798 [inline]
do_epoll_wait+0x6ad/0xf00 fs/eventpoll.c:2226
__do_sys_epoll_wait fs/eventpoll.c:2238 [inline]
__se_sys_epoll_wait fs/eventpoll.c:2233 [inline]
__x64_sys_epoll_wait+0xf6/0x120 fs/eventpoll.c:2233
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0x0000001b -> 0x00000001
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 25834 Comm: syz-executor.1 Tainted: G W 5.14.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 86b18aaa2b ("skbuff: fix a data race in skb_queue_len()")
Cc: Qian Cai <cai@lca.pw>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c4cea8fa7 upstream.
If the sendmsg() call in vhost_tx_batch() fails, both the 'batched_xdp'
and 'done_idx' indexes are left unchanged. If such failure happens
when batched_xdp == VHOST_NET_BATCH, the next call to
vhost_net_build_xdp() will access and write memory outside the xdp
buffers area.
Since sendmsg() can only error with EBADFD, this change addresses the
issue explicitly freeing the XDP buffers batch on error.
Fixes: 0a0be13b8f ("vhost_net: batch submitting XDP buffers to underlayer sockets")
Suggested-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec783c7cb2 upstream.
We need to import the 'sys' package since the script has called
sys.exit() method.
Fixes: 6ad7cbc015 ("Makefile: Add clang-tidy and static analyzer support to makefile")
Signed-off-by: Kortan <kortanzh@gmail.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5c102238c upstream.
There is an off-by-one problem in ipa_table_init_add(), when
initializing filter tables.
In that function, the number of filter table entries is determined
based on the number of set bits in the filter map. However that
count does *not* include the extra "slot" in the filter table that
holds the filter map itself. Meanwhile, ipa_table_addr() *does*
include the filter map in the memory it returns, but because the
count it's provided doesn't include it, it includes one too few
table entries.
Fix this by including the extra slot for the filter map in the count
computed in ipa_table_init_add().
Note: ipa_filter_reset_table() does not have this problem; it resets
filter table entries one by one, but does not overwrite the filter
bitmap.
Fixes: 2b9feef2b6 ("soc: qcom: ipa: filter and routing tables")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b89a05b21f upstream.
In perf_event_addr_filters_apply, the task associated with
the event (event->ctx->task) is read using READ_ONCE at the beginning
of the function, checked, and then re-read from event->ctx->task,
voiding all guarantees of the checks. Reuse the value that was read by
READ_ONCE to ensure the consistency of the task struct throughout the
function.
Fixes: 375637bc52 ("perf/core: Introduce address range filtering")
Signed-off-by: Baptiste Lepers <baptiste.lepers@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20210906015310.12802-1-baptiste.lepers@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70f437fb43 upstream.
Dispatching requests inline with the .queue_rq() call may block while
holding the send_mutex. If the tcp io_work also happens to schedule, it
may see the req_list is non-empty, leaving "pending" true and remaining
in TASK_RUNNING. Since io_work is of higher scheduling priority, the
.queue_rq task may not get a chance to run, blocking forward progress
and leading to io timeouts.
Instead of checking for pending requests within io_work, let the queueing
restart io_work outside the send_mutex lock if there is more work to be
done.
Fixes: a0fdd14180 ("nvme-tcp: rerun io_work if req_list is not empty")
Reported-by: Samuel Jones <sjones@kalrayinc.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee27e330a9 upstream.
Fixes the below flow of sleeping in atomic context by releasing
the RCU lock before calling to free_match_list.
build_match_list() <- disables preempt
-> free_match_list()
-> tree_put_node()
-> down_write_ref_node() <- take write lock
Fixes: 693c6883bb ("net/mlx5: Add hash table for flow groups in flow table")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 57f0ff059e upstream.
It's later supposed to be either a correct address or NULL. Without the
initialization, it may contain an undefined value which results in the
following segmentation fault:
# perf top --sort comm -g --ignore-callees=do_idle
terminates with:
#0 0x00007ffff56b7685 in __strlen_avx2 () from /lib64/libc.so.6
#1 0x00007ffff55e3802 in strdup () from /lib64/libc.so.6
#2 0x00005555558cb139 in hist_entry__init (callchain_size=<optimized out>, sample_self=true, template=0x7fffde7fb110, he=0x7fffd801c250) at util/hist.c:489
#3 hist_entry__new (template=template@entry=0x7fffde7fb110, sample_self=sample_self@entry=true) at util/hist.c:564
#4 0x00005555558cb4ba in hists__findnew_entry (hists=hists@entry=0x5555561d9e38, entry=entry@entry=0x7fffde7fb110, al=al@entry=0x7fffde7fb420,
sample_self=sample_self@entry=true) at util/hist.c:657
#5 0x00005555558cba1b in __hists__add_entry (hists=hists@entry=0x5555561d9e38, al=0x7fffde7fb420, sym_parent=<optimized out>, bi=bi@entry=0x0, mi=mi@entry=0x0,
sample=sample@entry=0x7fffde7fb4b0, sample_self=true, ops=0x0, block_info=0x0) at util/hist.c:288
#6 0x00005555558cbb70 in hists__add_entry (sample_self=true, sample=0x7fffde7fb4b0, mi=0x0, bi=0x0, sym_parent=<optimized out>, al=<optimized out>, hists=0x5555561d9e38)
at util/hist.c:1056
#7 iter_add_single_cumulative_entry (iter=0x7fffde7fb460, al=<optimized out>) at util/hist.c:1056
#8 0x00005555558cc8a4 in hist_entry_iter__add (iter=iter@entry=0x7fffde7fb460, al=al@entry=0x7fffde7fb420, max_stack_depth=<optimized out>, arg=arg@entry=0x7fffffff7db0)
at util/hist.c:1231
#9 0x00005555557cdc9a in perf_event__process_sample (machine=<optimized out>, sample=0x7fffde7fb4b0, evsel=<optimized out>, event=<optimized out>, tool=0x7fffffff7db0)
at builtin-top.c:842
#10 deliver_event (qe=<optimized out>, qevent=<optimized out>) at builtin-top.c:1202
#11 0x00005555558a9318 in do_flush (show_progress=false, oe=0x7fffffff80e0) at util/ordered-events.c:244
#12 __ordered_events__flush (oe=oe@entry=0x7fffffff80e0, how=how@entry=OE_FLUSH__TOP, timestamp=timestamp@entry=0) at util/ordered-events.c:323
#13 0x00005555558a9789 in __ordered_events__flush (timestamp=<optimized out>, how=<optimized out>, oe=<optimized out>) at util/ordered-events.c:339
#14 ordered_events__flush (how=OE_FLUSH__TOP, oe=0x7fffffff80e0) at util/ordered-events.c:341
#15 ordered_events__flush (oe=oe@entry=0x7fffffff80e0, how=how@entry=OE_FLUSH__TOP) at util/ordered-events.c:339
#16 0x00005555557cd631 in process_thread (arg=0x7fffffff7db0) at builtin-top.c:1114
#17 0x00007ffff7bb817a in start_thread () from /lib64/libpthread.so.0
#18 0x00007ffff5656dc3 in clone () from /lib64/libc.so.6
If you look at the frame #2, the code is:
488 if (he->srcline) {
489 he->srcline = strdup(he->srcline);
490 if (he->srcline == NULL)
491 goto err_rawdata;
492 }
If he->srcline is not NULL (it is not NULL if it is uninitialized rubbish),
it gets strdupped and strdupping a rubbish random string causes the problem.
Also, if you look at the commit 1fb7d06a50, it adds the srcline property
into the struct, but not initializing it everywhere needed.
Committer notes:
Now I see, when using --ignore-callees=do_idle we end up here at line
2189 in add_callchain_ip():
2181 if (al.sym != NULL) {
2182 if (perf_hpp_list.parent && !*parent &&
2183 symbol__match_regex(al.sym, &parent_regex))
2184 *parent = al.sym;
2185 else if (have_ignore_callees && root_al &&
2186 symbol__match_regex(al.sym, &ignore_callees_regex)) {
2187 /* Treat this symbol as the root,
2188 forgetting its callees. */
2189 *root_al = al;
2190 callchain_cursor_reset(cursor);
2191 }
2192 }
And the al that doesn't have the ->srcline field initialized will be
copied to the root_al, so then, back to:
1211 int hist_entry_iter__add(struct hist_entry_iter *iter, struct addr_location *al,
1212 int max_stack_depth, void *arg)
1213 {
1214 int err, err2;
1215 struct map *alm = NULL;
1216
1217 if (al)
1218 alm = map__get(al->map);
1219
1220 err = sample__resolve_callchain(iter->sample, &callchain_cursor, &iter->parent,
1221 iter->evsel, al, max_stack_depth);
1222 if (err) {
1223 map__put(alm);
1224 return err;
1225 }
1226
1227 err = iter->ops->prepare_entry(iter, al);
1228 if (err)
1229 goto out;
1230
1231 err = iter->ops->add_single_entry(iter, al);
1232 if (err)
1233 goto out;
1234
That al at line 1221 is what hist_entry_iter__add() (called from
sample__resolve_callchain()) saw as 'root_al', and then:
iter->ops->add_single_entry(iter, al);
will go on with al->srcline with a bogus value, I'll add the above
sequence to the cset and apply, thanks!
Signed-off-by: Michael Petlan <mpetlan@redhat.com>
CC: Milian Wolff <milian.wolff@kdab.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Fixes: 1fb7d06a50 ("perf report Use srcline from callchain for hist entries")
Link: https //lore.kernel.org/r/20210719145332.29747-1-mpetlan@redhat.com
Reported-by: Juri Lelli <jlelli@redhat.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 040b8907cc upstream.
With the new static annotation, the compiler warns when the functions
are actually unused:
drivers/gpu/drm/rockchip/cdn-dp-core.c:1123:12: error: 'cdn_dp_resume' defined but not used [-Werror=unused-function]
1123 | static int cdn_dp_resume(struct device *dev)
| ^~~~~~~~~~~~~
Mark them __maybe_unused to suppress that warning as well.
[ Not so 'new' static annotations any more, and I removed the part of
the patch that added __maybe_unused to cdn_dp_suspend(), because it's
used by the shutdown/remove code.
So only the resume function ends up possibly unused if CONFIG_PM isn't
set - Linus ]
Fixes: 7c49abb4c2 ("drm/rockchip: cdn-dp-core: Make cdn_dp_core_suspend/resume static")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f4bb62e64c upstream.
In tipc_sk_enqueue() we use hardcoded 2 jiffies to extract
socket buffer from generic queue to particular socket.
The 2 jiffies is too short in case there are other high priority
tasks get CPU cycles for multiple jiffies update. As result, no
buffer could be enqueued to particular socket.
To solve this, we switch to use constant timeout 20msecs.
Then, the function will be expired between 2 jiffies (CONFIG_100HZ)
and 20 jiffies (CONFIG_1000HZ).
Fixes: c637c10355 ("tipc: resolve race problem at unicast message reception")
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e3f0cc1a94 upstream.
A number of users have reported that they were not able to get the PHY
to successfully link up, especially after commit c36757eb9d ("net:
phy: consider AN_RESTART status when reading link status") where we
stopped reading just BMSR, but we also read BMCR to determine the link
status.
Andrius at NetBSD did a wonderful job at debugging the problem
and found out that the MDIO bus clock frequency would be incorrectly set
back to its default value which would prevent the MDIO bus controller
from reading PHY registers properly. Back when we only read BMSR, if we
read all 1s, we could falsely indicate a link status, though in general
there is a cable plugged in, so this went unnoticed. After a second read
of BMCR was added, a wrong read will lead to the inability to determine
a link UP condition which is when it started to be visibly broken, even
if it was long before that.
The fix consists in restoring the value of the MD_CSR register that was
set prior to the MAC reset.
Link: http://gnats.netbsd.org/cgi-bin/query-pr-single.pl?number=53494
Fixes: 90f750a81a ("r6040: consolidate MAC reset to its own function")
Reported-by: Andrius V <vezhlys@gmail.com>
Reported-by: Darek Strugacz <darek.strugacz@op.pl>
Tested-by: Darek Strugacz <darek.strugacz@op.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b6ff7eb66 upstream.
The reference count leak issue may take place in an error handling
path. If both conditions of tunnel->version == L2TP_HDR_VER_3 and the
return value of l2tp_v3_ensure_opt_in_linear is nonzero, the function
would directly jump to label invalid, without decrementing the reference
count of the l2tp_session object session increased earlier by
l2tp_tunnel_get_session(). This may result in refcount leaks.
Fix this issue by decrease the reference count before jumping to the
label invalid.
Fixes: 4522a70db7 ("l2tp: fix reading optional fields of L2TPv3")
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9ea761fdd upstream.
Commit 2677d20677 ("dccp: don't free ccid2_hc_tx_sock ...") fixed
a UAF but reintroduced CVE-2017-6074.
When the sock is cloned, two dccps_hc_tx_ccid will reference to the
same ccid. So one can free the ccid object twice from two socks after
cloning.
This issue was found by "Hadar Manor" as well and assigned with
CVE-2020-16119, which was fixed in Ubuntu's kernel. So here I port
the patch from Ubuntu to fix it.
The patch prevents cloned socks from referencing the same ccid.
Fixes: 2677d20677 ("dccp: don't free ccid2_hc_tx_sock ...")
Signed-off-by: Zhenpeng Lin <zplin@psu.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7366c23ff4 upstream.
Building dp83640.c on arch/parisc/ produces a build warning for
PAGE0 being redefined. Since the macro is not used in the dp83640
driver, just make it a comment for documentation purposes.
In file included from ../drivers/net/phy/dp83640.c:23:
../drivers/net/phy/dp83640_reg.h:8: warning: "PAGE0" redefined
8 | #define PAGE0 0x0000
from ../drivers/net/phy/dp83640.c:11:
../arch/parisc/include/asm/page.h:187: note: this is the location of the previous definition
187 | #define PAGE0 ((struct zeropage *)__PAGE_OFFSET)
Fixes: cb646e2b02 ("ptp: Added a clock driver for the National Semiconductor PHYTER.")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Richard Cochran <richard.cochran@omicron.at>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210913220605.19682-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c3a0a018e upstream.
Remove the assert from the callback priv lookup function since it does
not require RTNL lock and is already protected by flow_indr_block_lock.
This will avoid warnings from being emitted to dmesg if the driver
registers its callback after an ingress qdisc was created for a
netdevice.
The warnings started after the following patch was merged:
commit 74fc4f8287 ("net: Fix offloading indirect devices dependency on qdisc order creation")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc19862ffe upstream.
syzbot reported an use-after-free crash:
BUG: KASAN: use-after-free in tipc_recvmsg+0xf77/0xf90 net/tipc/socket.c:1979
Call Trace:
tipc_recvmsg+0xf77/0xf90 net/tipc/socket.c:1979
sock_recvmsg_nosec net/socket.c:943 [inline]
sock_recvmsg net/socket.c:961 [inline]
sock_recvmsg+0xca/0x110 net/socket.c:957
tipc_conn_rcv_from_sock+0x162/0x2f0 net/tipc/topsrv.c:398
tipc_conn_recv_work+0xeb/0x190 net/tipc/topsrv.c:421
process_one_work+0x98d/0x1630 kernel/workqueue.c:2276
worker_thread+0x658/0x11f0 kernel/workqueue.c:2422
As Hoang pointed out, it was caused by skb_cb->bytes_read still accessed
after calling tsk_advance_rx_queue() to free the skb in tipc_recvmsg().
This patch is to fix it by accessing skb_cb->bytes_read earlier than
calling tsk_advance_rx_queue().
Fixes: f4919ff59c ("tipc: keep the skb in rcv queue until the whole data is read")
Reported-by: syzbot+e6741b97d5552f97c24d@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 34b1999da9 upstream.
Jiri Olsa reported a fault when running:
# cat /proc/kallsyms | grep ksys_read
ffffffff8136d580 T ksys_read
# objdump -d --start-address=0xffffffff8136d580 --stop-address=0xffffffff8136d590 /proc/kcore
/proc/kcore: file format elf64-x86-64
Segmentation fault
general protection fault, probably for non-canonical address 0xf887ffcbff000: 0000 [#1] SMP PTI
CPU: 12 PID: 1079 Comm: objdump Not tainted 5.14.0-rc5qemu+ #508
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-4.fc34 04/01/2014
RIP: 0010:kern_addr_valid
Call Trace:
read_kcore
? rcu_read_lock_sched_held
? rcu_read_lock_sched_held
? rcu_read_lock_sched_held
? trace_hardirqs_on
? rcu_read_lock_sched_held
? lock_acquire
? lock_acquire
? rcu_read_lock_sched_held
? lock_acquire
? rcu_read_lock_sched_held
? rcu_read_lock_sched_held
? rcu_read_lock_sched_held
? lock_release
? _raw_spin_unlock
? __handle_mm_fault
? rcu_read_lock_sched_held
? lock_acquire
? rcu_read_lock_sched_held
? lock_release
proc_reg_read
? vfs_read
vfs_read
ksys_read
do_syscall_64
entry_SYSCALL_64_after_hwframe
The fault happens because kern_addr_valid() dereferences existent but not
present PMD in the high kernel mappings.
Such PMDs are created when free_kernel_image_pages() frees regions larger
than 2Mb. In this case, a part of the freed memory is mapped with PMDs and
the set_memory_np_noalias() -> ... -> __change_page_attr() sequence will
mark the PMD as not present rather than wipe it completely.
Have kern_addr_valid() check whether higher level page table entries are
present before trying to dereference them to fix this issue and to avoid
similar issues in the future.
Stable backporting note:
------------------------
Note that the stable marking is for all active stable branches because
there could be cases where pagetable entries exist but are not valid -
see 9a14aefc1d ("x86: cpa, fix lookup_address"), for example. So make
sure to be on the safe side here and use pXY_present() accessors rather
than pXY_none() which could #GP when accessing pages in the direct map.
Also see:
c40a56a781 ("x86/mm/init: Remove freed kernel image areas from alias mapping")
for more info.
Reported-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: Dave Hansen <dave.hansen@intel.com>
Tested-by: Jiri Olsa <jolsa@redhat.com>
Cc: <stable@vger.kernel.org> # 4.4+
Link: https://lkml.kernel.org/r/20210819132717.19358-1-rppt@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aeef8b5089 upstream.
The end address passed to memtype_reserve() is handed directly to
sanitize_phys(). However, end is exclusive and sanitize_phys() expects
an inclusive address. If end falls at the end of the physical address
space, sanitize_phys() will return 0. This can result in drivers
failing to load, and the following warning:
WARNING: CPU: 26 PID: 749 at arch/x86/mm/pat.c:354 reserve_memtype+0x262/0x450
reserve_memtype failed: [mem 0x3ffffff00000-0xffffffffffffffff], req uncached-minus
Call Trace:
[<ffffffffa427b1f2>] reserve_memtype+0x262/0x450
[<ffffffffa42764aa>] ioremap_nocache+0x1a/0x20
[<ffffffffc04620a1>] mpt3sas_base_map_resources+0x151/0xa60 [mpt3sas]
[<ffffffffc0465555>] mpt3sas_base_attach+0xf5/0xa50 [mpt3sas]
---[ end trace 6d6eea4438db89ef ]---
ioremap reserve_memtype failed -22
mpt3sas_cm0: unable to map adapter memory! or resource not found
mpt3sas_cm0: failure at drivers/scsi/mpt3sas/mpt3sas_scsih.c:10597/_scsih_probe()!
Fix this by passing the inclusive end address to sanitize_phys().
Fixes: 510ee090ab ("x86/mm/pat: Prepare {reserve, free}_memtype() for "decoy" addresses")
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/x49o8a3pu5i.fsf@segfault.boston.devel.redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f2faea8b64 upstream.
When we forcefully evict a mapping from the the address space and thus the
MMU context, the MMU context is leaked, as the mapping no longer points to
it, so it doesn't get freed when the GEM object is destroyed. Add the
mssing context put to fix the leak.
Cc: stable@vger.kernel.org # 5.4
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d6408538f0 upstream.
Move the refcount manipulation of the MMU context to the point where the
hardware state is programmed. At that point it is also known if a previous
MMU state is still there, or the state needs to be reprogrammed with a
potentially different context.
Cc: stable@vger.kernel.org # 5.4
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f3eea9d01 upstream.
The MMU state may be kept across a runtime suspend/resume cycle, as we
avoid a full hardware reset to keep the latency of the runtime PM small.
Don't pretend that the MMU state is lost in driver state. The MMU
context is pushed out when new HW jobs with a different context are
coming in. The only exception to this is when the GPU is unbound, in
which case we need to make sure to also free the last active context.
Cc: stable@vger.kernel.org # 5.4
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23e0f5a57d upstream.
While the DMA frontend can only be active when the MMU context is set, the
reverse isn't necessarily true, as the frontend can be stopped while the
MMU state is kept. Stop treating mmu_context being set as a indication that
the frontend is running and instead add a explicit property.
Cc: stable@vger.kernel.org # 5.4
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cda7532916 upstream.
The prev context is the MMU context at the time of the job
queueing in hardware. As a job might be queued multiple times
due to recovery after a GPU hang, we need to make sure to put
the stale prev MMU context from a prior queuing, to avoid the
reference and thus the MMU context leaking.
Cc: stable@vger.kernel.org # 5.4
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e35ac9d0b5 upstream.
When we need a buffer for SVE register state we call sve_alloc() to make
sure that one is there. In order to avoid repeated allocations and frees
we keep the buffer around unless we change vector length and just memset()
it to ensure a clean register state. The function that deals with this
takes the task to operate on as an argument, however in the case where we
do a memset() we initialise using the SVE state size for the current task
rather than the task passed as an argument.
This is only an issue in the case where we are setting the register state
for a task via ptrace and the task being configured has a different vector
length to the task tracing it. In the case where the buffer is larger in
the traced process we will leak old state from the traced process to
itself, in the case where the buffer is smaller in the traced process we
will overflow the buffer and corrupt memory.
Fixes: bc0ee47603 ("arm64/sve: Core task context handling")
Cc: <stable@vger.kernel.org> # 4.15.x
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210909165356.10675-1-broonie@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 16c8d2df7e upstream.
When setting up the next segment, we check what type the iter is and
handle it accordingly. However, when incrementing and processed amount
we do not, and both iter advance and addr/len are adjusted, regardless
of type. Split the increment side just like we do on the setup side.
Fixes: 4017eb91a9 ("io_uring: make loop_rw_iter() use original user supplied pointers")
Cc: stable@vger.kernel.org
Reported-by: Valentina Palmiotti <vpalmiotti@gmail.com>
Reviewed-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f93e834fa upstream.
The mount option max_inline ranges from 0 to the sectorsize (which is
now equal to page size). But we parse the mount options too early and
before the actual sectorsize is read from the superblock. So the upper
limit of max_inline is unaware of the actual sectorsize and is limited
by the temporary sectorsize 4096, even on a system where the default
sectorsize is 64K.
Fix this by reading the superblock sectorsize before the mount option
parse.
Reported-by: Alexander Tsvetkov <alexander.tsvetkov@oracle.com>
CC: stable@vger.kernel.org # 5.4+
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fw_node pointer has already been retrieved, and using it allows
us to remove a downstream patch to the firmware driver.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
commit 6e3cd95234 upstream.
On recent Intel systems the HPET stops working when the system reaches PC10
idle state.
The approach of adding PCI ids to the early quirks to disable HPET on
these systems is a whack a mole game which makes no sense.
Check for PC10 instead and force disable HPET if supported. The check is
overbroad as it does not take ACPI, intel_idle enablement and command
line parameters into account. That's fine as long as there is at least
PMTIMER available to calibrate the TSC frequency. The decision can be
overruled by adding "hpet=force" on the kernel command line.
Remove the related early PCI quirks for affected Ice Cake and Coffin Lake
systems as they are not longer required. That should also cover all
other systems, i.e. Tiger Rag and newer generations, which are most
likely affected by this as well.
Fixes: Yet another hardware trainwreck
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Rafael J. Wysocki <rafael@kernel.org>
Cc: stable@vger.kernel.org
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3958b9c34c upstream.
Commit
3c73b81a91 ("x86/entry, selftests: Further improve user entry sanity checks")
added a warning if AC is set when in the kernel.
Commit
662a022189 ("x86/entry: Fix AC assertion")
changed the warning to only fire if the CPU supports SMAP.
However, the warning can still trigger on a machine that supports SMAP
but where it's disabled in the kernel config and when running the
syscall_nt selftest, for example:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 49 at irqentry_enter_from_user_mode
CPU: 0 PID: 49 Comm: init Tainted: G T 5.15.0-rc4+ #98 e6202628ee053b4f310759978284bd8bb0ce6905
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
RIP: 0010:irqentry_enter_from_user_mode
...
Call Trace:
? irqentry_enter
? exc_general_protection
? asm_exc_general_protection
? asm_exc_general_protectio
IS_ENABLED(CONFIG_X86_SMAP) could be added to the warning condition, but
even this would not be enough in case SMAP is disabled at boot time with
the "nosmap" parameter.
To be consistent with "nosmap" behaviour, clear X86_FEATURE_SMAP when
!CONFIG_X86_SMAP.
Found using entry-fuzz + satrandconfig.
[ bp: Massage commit message. ]
Fixes: 3c73b81a91 ("x86/entry, selftests: Further improve user entry sanity checks")
Fixes: 662a022189 ("x86/entry: Fix AC assertion")
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20211003223423.8666-1-vegard.nossum@oracle.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit eb8257a121 ]
On pseries LPAR when an empty slot is assigned to partition OR in single
LPAR mode, kdump kernel crashes during issuing PHB reset.
In the kdump scenario, we traverse all PHBs and issue reset using the
pe_config_addr of the first child device present under each PHB. However
the code assumes that none of the PHB slots can be empty and uses
list_first_entry() to get the first child device under the PHB. Since
list_first_entry() expects the list to be non-empty, it returns an
invalid pci_dn entry and ends up accessing NULL phb pointer under
pci_dn->phb causing kdump kernel crash.
This patch fixes the below kdump kernel crash by skipping empty slots:
audit: initializing netlink subsys (disabled)
thermal_sys: Registered thermal governor 'fair_share'
thermal_sys: Registered thermal governor 'step_wise'
cpuidle: using governor menu
pstore: Registered nvram as persistent store backend
Issue PHB reset ...
audit: type=2000 audit(1631267818.000:1): state=initialized audit_enabled=0 res=1
BUG: Kernel NULL pointer dereference on read at 0x00000268
Faulting instruction address: 0xc000000008101fb0
Oops: Kernel access of bad area, sig: 7 [#1]
LE PAGE_SIZE=64K MMU=Radix SMP NR_CPUS=2048 NUMA pSeries
Modules linked in:
CPU: 7 PID: 1 Comm: swapper/7 Not tainted 5.14.0 #1
NIP: c000000008101fb0 LR: c000000009284ccc CTR: c000000008029d70
REGS: c00000001161b840 TRAP: 0300 Not tainted (5.14.0)
MSR: 8000000002009033 <SF,VEC,EE,ME,IR,DR,RI,LE> CR: 28000224 XER: 20040002
CFAR: c000000008101f0c DAR: 0000000000000268 DSISR: 00080000 IRQMASK: 0
...
NIP pseries_eeh_get_pe_config_addr+0x100/0x1b0
LR __machine_initcall_pseries_eeh_pseries_init+0x2cc/0x350
Call Trace:
0xc00000001161bb80 (unreliable)
__machine_initcall_pseries_eeh_pseries_init+0x2cc/0x350
do_one_initcall+0x60/0x2d0
kernel_init_freeable+0x350/0x3f8
kernel_init+0x3c/0x17c
ret_from_kernel_thread+0x5c/0x64
Fixes: 5a090f7c36 ("powerpc/pseries: PCIE PHB reset")
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.ibm.com>
[mpe: Tweak wording and trim oops]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/163215558252.413351.8600189949820258982.stgit@jupiter
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59a4e0d551 ]
As far as I can tell this should be enabled on rv32 as well, I'm not
sure why it's rv64-only. checksyscalls is complaining about our lack of
clone3() on rv32.
Fixes: 56ac5e2139 ("riscv: enable sys_clone3 syscall for rv64")
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8bb0ab3ae7 ]
riscv architectures relying on mmap_sem for write in their
arch_setup_additional_pages. If the waiting task gets killed by the oom
killer it would block oom_reaper from asynchronous address space reclaim
and reduce the chances of timely OOM resolving. Wait for the lock in
the killable mode and return with EINTR if the task got killed while
waiting.
Signed-off-by: Tong Tiangen <tongtiangen@huawei.com>
Reviewed-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Fixes: 76d2a0493a ("RISC-V: Init and Halt Code")
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6558b646ce ]
acpi_i2c_find_adapter_by_handle() calls bus_find_device() which takes a
reference on the adapter which is never released which will result in a
reference count leak and render the adapter unremovable. Make sure to
put the adapter after creating the client in the same manner that we do
for OF.
Fixes: 525e6fabea ("i2c / ACPI: add support for ACPI reconfigure notifications")
Signed-off-by: Jamie Iles <quic_jiles@quicinc.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[wsa: fixed title]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23c216b335 ]
According to dma-api.rst, the dma_get_required_mask() helper should return
"the mask that the platform requires to operate efficiently". Which in
the case of PPC64 means the bypass mask and not a mask from an IOMMU table
which is shorter and slower to use due to map/unmap operations (especially
expensive on "pseries").
However the existing implementation ignores the possibility of bypassing
and returns the IOMMU table mask on the pseries platform which makes some
drivers (mpt3sas is one example) choose 32bit DMA even though bypass is
supported. The powernv platform sort of handles it by having a bigger
default window with a mask >=40 but it only works as drivers choose
63/64bit if the required mask is >32 which is rather pointless.
This reintroduces the bypass capability check to let drivers make
a better choice of the DMA mask.
Fixes: f1565c24b5 ("powerpc: use the generic dma_ops_bypass mode")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210930034454.95794-1-aik@ozlabs.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d6c414cd2 ]
The commit 6da5b0f027 ("net: ensure unbound datagram socket to be
chosen when not in a VRF") modified compute_score() so that a device
match is always made, not just in the case of an l3mdev skb, then
increments the score also for unbound sockets. This ensures that
sockets bound to an l3mdev are never selected when not in a VRF.
But as unbound and bound sockets are now scored equally, this results
in the last opened socket being selected if there are matches in the
default VRF for an unbound socket and a socket bound to a dev that is
not an l3mdev. However, handling prior to this commit was to always
select the bound socket in this case. Reinstate this handling by
incrementing the score only for bound sockets. The required isolation
due to choosing between an unbound socket and a socket bound to an
l3mdev remains in place due to the device match always being made.
The same approach is taken for compute_score() for stream sockets.
Fixes: 6da5b0f027 ("net: ensure unbound datagram socket to be chosen when not in a VRF")
Fixes: e78190581a ("net: ensure unbound stream socket to be chosen when not in a VRF")
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/cf0a8523-b362-1edf-ee78-eef63cbbb428@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e5a20573a ]
When VSI set up failed in i40e_probe() as part of PF switch set up
driver was trying to free misc IRQ vectors in
i40e_clear_interrupt_scheme and produced a kernel Oops:
Trying to free already-free IRQ 266
WARNING: CPU: 0 PID: 5 at kernel/irq/manage.c:1731 __free_irq+0x9a/0x300
Workqueue: events work_for_cpu_fn
RIP: 0010:__free_irq+0x9a/0x300
Call Trace:
? synchronize_irq+0x3a/0xa0
free_irq+0x2e/0x60
i40e_clear_interrupt_scheme+0x53/0x190 [i40e]
i40e_probe.part.108+0x134b/0x1a40 [i40e]
? kmem_cache_alloc+0x158/0x1c0
? acpi_ut_update_ref_count.part.1+0x8e/0x345
? acpi_ut_update_object_reference+0x15e/0x1e2
? strstr+0x21/0x70
? irq_get_irq_data+0xa/0x20
? mp_check_pin_attr+0x13/0xc0
? irq_get_irq_data+0xa/0x20
? mp_map_pin_to_irq+0xd3/0x2f0
? acpi_register_gsi_ioapic+0x93/0x170
? pci_conf1_read+0xa4/0x100
? pci_bus_read_config_word+0x49/0x70
? do_pci_enable_device+0xcc/0x100
local_pci_probe+0x41/0x90
work_for_cpu_fn+0x16/0x20
process_one_work+0x1a7/0x360
worker_thread+0x1cf/0x390
? create_worker+0x1a0/0x1a0
kthread+0x112/0x130
? kthread_flush_work_fn+0x10/0x10
ret_from_fork+0x1f/0x40
The problem is that at that point misc IRQ vectors
were not allocated yet and we get a call trace
that driver is trying to free already free IRQ vectors.
Add a check in i40e_clear_interrupt_scheme for __I40E_MISC_IRQ_REQUESTED
PF state before calling i40e_free_misc_vector. This state is set only if
misc IRQ vectors were properly initialized.
Fixes: c17401a1dd ("i40e: use separate state bit for miscellaneous IRQ setup")
Reported-by: PJ Waskiewicz <pwaskiewicz@jumptrading.com>
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 857b6c6f66 ]
The loop in i40e_get_capabilities can never end. The problem is that
although i40e_aq_discover_capabilities returns with an error if there's
a firmware problem, the returned error is not checked. There is a check for
pf->hw.aq.asq_last_status but that value is set to I40E_AQ_RC_OK on most
firmware problems.
When i40e_aq_discover_capabilities encounters a firmware problem, it will
encounter the same problem on its next invocation. As the result, the loop
becomes endless. We hit this with I40E_ERR_ADMIN_QUEUE_TIMEOUT but looking
at the code, it can happen with a range of other firmware errors.
I don't know what the correct behavior should be: whether the firmware
should be retried a few times, or whether pf->hw.aq.asq_last_status should
be always set to the encountered firmware error (but then it would be
pointless and can be just replaced by the i40e_aq_discover_capabilities
return value). However, the current behavior with an endless loop under the
rtnl mutex(!) is unacceptable and Intel has not submitted a fix, although we
explained the bug to them 7 months ago.
This may not be the best possible fix but it's better than hanging the whole
system on a firmware bug.
Fixes: 56a62fc868 ("i40e: init code and hardware support")
Tested-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d343679919 ]
rtnl_fill_statsinfo() is filling skb with one mandatory if_stats_msg structure.
nlmsg_put(skb, pid, seq, type, sizeof(struct if_stats_msg), flags);
But if_nlmsg_stats_size() never considered the needed storage.
This bug did not show up because alloc_skb(X) allocates skb with
extra tailroom, because of added alignments. This could very well
be changed in the future to have deterministic behavior.
Fixes: 10c9ead9f3 ("rtnetlink: add new RTM_GETSTATS message to dump link stats")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Roopa Prabhu <roopa@nvidia.com>
Acked-by: Roopa Prabhu <roopa@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 922aa9bcac ]
Prevent possible crashes when cleaning up after unsuccessful
initializations.
Fixes: 893ce44df5 ("gve: Add basic driver framework for Compute Engine Virtual NIC")
Signed-off-by: Tao Liu <xliutaox@google.com>
Signed-off-by: Catherine Sully <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d03477ee10 ]
The qpl_map_size is rounded up to a multiple of sizeof(long), but the
number of qpls doesn't have to be.
Fixes: f5cedc84a3 ("gve: Add transmit and receive support")
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: Jeroen de Borst <jeroendb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11b8e2bb98 ]
The gbefb driver not only registers a driver but also the device for that
driver. This is all well and good when run on the IP32 machines that are
supported by the driver but since the driver supports building with
COMPILE_TEST we might also be building on other platforms which do not have
this hardware and will crash instantiating the driver. Add an IS_ENABLED()
check so we compile out the device registration if we don't have the Kconfig
option for the machine enabled.
Fixes: 552ccf6b25 ("video: fbdev: gbefb: add COMPILE_TEST support")
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921212102.30803-1-broonie@kernel.org
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c64c8e04a1 ]
Recent rework, which made HDMI PHY driver a platform device, inadvertely
reversed clock setup order. HW is very touchy about it. Proper way is to
handle controllers resets and clocks first and HDMI PHYs second.
Currently, without this fix, first mode set completely fails (nothing on
HDMI monitor) on H3 era PHYs. On H6, it still somehow work.
Move HDMI PHY reset & clocks handling to sun8i_hdmi_phy_init() which
will assure that code is executed after controllers reset & clocks are
handled. Additionally, add sun8i_hdmi_phy_deinit() which will deinit
them at controllers driver unload.
Tested on A64, H3, H6 and R40.
Fixes: 9bf3797796 ("drm/sun4i: dw-hdmi: Make HDMI PHY into a platform device")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210915175836.3158839-1-jernej.skrabec@gmail.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b13a270ace ]
Commit 94f6345712 ("bus: ti-sysc: Implement quirk handling for
CLKDM_NOAUTO") should have also added the quirk for dra7 dcan1 in
addition to dcan2 for errata i893 handling.
Let's also pass the quirk flag for legacy mode booting for if "ti,hwmods"
dts property is used with related dcan hwmod data. This should be only
needed if anybody needs to git bisect earlier stable trees though.
Fixes: 94f6345712 ("bus: ti-sysc: Implement quirk handling for CLKDM_NOAUTO")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7707a4d01a ]
While existing code is correct, KCSAN is reporting
a data-race in netlink_insert / netlink_sendmsg [1]
It is correct to read nlk->bound without a lock, as netlink_autobind()
will acquire all needed locks.
[1]
BUG: KCSAN: data-race in netlink_insert / netlink_sendmsg
write to 0xffff8881031c8b30 of 1 bytes by task 18752 on cpu 0:
netlink_insert+0x5cc/0x7f0 net/netlink/af_netlink.c:597
netlink_autobind+0xa9/0x150 net/netlink/af_netlink.c:842
netlink_sendmsg+0x479/0x7c0 net/netlink/af_netlink.c:1892
sock_sendmsg_nosec net/socket.c:703 [inline]
sock_sendmsg net/socket.c:723 [inline]
____sys_sendmsg+0x360/0x4d0 net/socket.c:2392
___sys_sendmsg net/socket.c:2446 [inline]
__sys_sendmsg+0x1ed/0x270 net/socket.c:2475
__do_sys_sendmsg net/socket.c:2484 [inline]
__se_sys_sendmsg net/socket.c:2482 [inline]
__x64_sys_sendmsg+0x42/0x50 net/socket.c:2482
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffff8881031c8b30 of 1 bytes by task 18751 on cpu 1:
netlink_sendmsg+0x270/0x7c0 net/netlink/af_netlink.c:1891
sock_sendmsg_nosec net/socket.c:703 [inline]
sock_sendmsg net/socket.c:723 [inline]
__sys_sendto+0x2a8/0x370 net/socket.c:2019
__do_sys_sendto net/socket.c:2031 [inline]
__se_sys_sendto net/socket.c:2027 [inline]
__x64_sys_sendto+0x74/0x90 net/socket.c:2027
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0x00 -> 0x01
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 18751 Comm: syz-executor.0 Not tainted 5.14.0-rc1-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: da314c9923 ("netlink: Replace rhash_portid with bound")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0854a05133 ]
Commit de1799667b ("net: bridge: add STP xstats")
added an additional nla_reserve_64bit() in br_fill_linkxstats(),
but forgot to update br_get_linkxstats_size() accordingly.
This can trigger the following in rtnl_stats_get()
WARN_ON(err == -EMSGSIZE);
Fixes: de1799667b ("net: bridge: add STP xstats")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Nikolay Aleksandrov <nikolay@nvidia.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dbe0b88064 ]
bridge_fill_linkxstats() is using nla_reserve_64bit().
We must use nla_total_size_64bit() instead of nla_total_size()
for corresponding data structure.
Fixes: 1080ab95e3 ("net: bridge: add support for IGMP/MLD stats and export them via netlink")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Nikolay Aleksandrov <nikolay@nvidia.com>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 783f3db030 ]
Any pending interrupt can prevent entering standby based power off state.
To avoid it, disable the GIC CPU interface.
Fixes: 8148d21360 ("ARM: imx6: register pm_power_off handler if "fsl,pmic-stby-poweroff" is set")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04fa4f03e3 ]
The LS1028A has two FlexCAN controller. These are compatible with
the ones from the LX2160A. Add the nodes.
The first controller was tested on the Kontron sl28 board.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7cd8b1542a ]
The driver can't be loaded automatically because it misses
module alias to be provided. Add corresponding MODULE_DEVICE_TABLE()
call to the driver.
Fixes: 863d08ece9 ("supports eg20t ptp clock")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eed183abc0 ]
Property phy-connection-type contains invalid value "sgmii-2500" per scheme
defined in file ethernet-controller.yaml.
Correct phy-connection-type value should be "2500base-x".
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 84e0f1c138 ("powerpc/mpc85xx: Add MDIO bus muxing support to the board device tree(s)")
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9a10440f0 ]
Currently in Rx data path IPsec crypto offloaded packets uses
csum_none flag, so checksum is handled by the stack, this naturally
have some performance/cpu utilization impact on such flows. As Nvidia
NIC starting from ConnectX6DX provides checksum complete value out of
the box also for such flows there is no sense in taking csum_none path,
furthermore the stack (xfrm) have the method to handle checksum complete
corrections for such flows i.e. IPsec trailer removal and consequently
checksum value adjustment.
Because of the above and in addition the ConnectX6DX is the first HW
which supports IPsec crypto offload then it is safe to report csum
complete for IPsec offloaded traffic.
Fixes: b2ac7541e3 ("net/mlx5e: IPsec: Add Connect-X IPsec Rx data path offload")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30e29a9a2b ]
In prealloc_elems_and_freelist(), the multiplication to calculate the
size passed to bpf_map_area_alloc() could lead to an integer overflow.
As a result, out-of-bounds write could occur in pcpu_freelist_populate()
as reported by KASAN:
[...]
[ 16.968613] BUG: KASAN: slab-out-of-bounds in pcpu_freelist_populate+0xd9/0x100
[ 16.969408] Write of size 8 at addr ffff888104fc6ea0 by task crash/78
[ 16.970038]
[ 16.970195] CPU: 0 PID: 78 Comm: crash Not tainted 5.15.0-rc2+ #1
[ 16.970878] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014
[ 16.972026] Call Trace:
[ 16.972306] dump_stack_lvl+0x34/0x44
[ 16.972687] print_address_description.constprop.0+0x21/0x140
[ 16.973297] ? pcpu_freelist_populate+0xd9/0x100
[ 16.973777] ? pcpu_freelist_populate+0xd9/0x100
[ 16.974257] kasan_report.cold+0x7f/0x11b
[ 16.974681] ? pcpu_freelist_populate+0xd9/0x100
[ 16.975190] pcpu_freelist_populate+0xd9/0x100
[ 16.975669] stack_map_alloc+0x209/0x2a0
[ 16.976106] __sys_bpf+0xd83/0x2ce0
[...]
The possibility of this overflow was originally discussed in [0], but
was overlooked.
Fix the integer overflow by changing elem_size to u64 from u32.
[0] https://lore.kernel.org/bpf/728b238e-a481-eb50-98e9-b0f430ab01e7@gmail.com/
Fixes: 557c0c6e7d ("bpf: convert stackmap to pre-allocation")
Signed-off-by: Tatsuhiko Yasumatsu <th.yasumatsu@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210930135545.173698-1-th.yasumatsu@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b232537074 ]
Starting with v5.15-rc1, we may now see some am335x beaglebone black
device produce the following error on pruss probe:
Unhandled fault: external abort on non-linefetch (0x1008) at 0xe0326000
This has started with the enabling of pruss for am335x in the dts files.
Turns out the is caused by the PRM reset handling not waiting for the
reset bit to clear. To fix the issue, let's always wait for the reset
bit to clear, even if there is a separate reset status register.
We attempted to fix a similar issue for dra7 iva with a udelay() in
commit effe89e400 ("soc: ti: omap-prm: Fix occasional abort on reset
deassert for dra7 iva"). There is no longer a need for the udelay()
for dra7 iva reset either with the check added for reset bit clearing.
Cc: Drew Fustini <pdp7pdp7@gmail.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: "H. Nikolaus Schaller" <hns@goldelico.com>
Cc: Robert Nelson <robertcnelson@gmail.com>
Cc: Yongqin Liu <yongqin.liu@linaro.org>
Fixes: effe89e400 ("soc: ti: omap-prm: Fix occasional abort on reset deassert for dra7 iva")
Reported-by: Matti Vaittinen <mazziesaccount@gmail.com>
Tested-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79e3445b38 ]
On ARM CPUs that lack div/mod instructions, ALU32 BPF_DIV and BPF_MOD are
implemented using a call to a helper function. Before, the emitted code
for those function calls failed to preserve caller-saved ARM registers.
Since some of those registers happen to be mapped to BPF registers, it
resulted in eBPF register values being overwritten.
This patch emits code to push and pop the remaining caller-saved ARM
registers r2-r3 into the stack during the div/mod function call. ARM
registers r0-r1 are used as arguments and return value, and those were
already saved and restored correctly.
Fixes: 39c13c204b ("arm: eBPF JIT compiler")
Signed-off-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe5c735d0d ]
There is a Killer AX1650 2x2 Wi-Fi 6 and Bluetooth 5.1 wireless adapter
found on Dell XPS 15 (9510) laptop, its configuration was present on
Linux v5.7, however accidentally it has been removed from the list of
supported devices, let's add it back.
The problem is manifested on driver initialization:
Intel(R) Wireless WiFi driver for Linux
iwlwifi 0000:00:14.3: enabling device (0000 -> 0002)
iwlwifi: No config found for PCI dev 43f0/1651, rev=0x354, rfid=0x10a100
iwlwifi: probe of 0000:00:14.3 failed with error -22
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=213939
Fixes: 3f910a2583 ("iwlwifi: pcie: convert all AX101 devices to the device tables")
Cc: Julien Wajsberg <felash@gmail.com>
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Acked-by: Luca Coelho <luca@coelho.fi>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210924122154.2376577-1-vladimir.zapolskiy@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d67ed2510d ]
CONFIG_OF can be set by a randconfig or by a user -- without setting the
early flattree option (OF_EARLY_FLATTREE). This causes build errors.
However, if randconfig or a user sets USE_OF in the Xtensa config,
the right kconfig symbols are set to fix the build.
Fixes these build errors:
../arch/xtensa/kernel/setup.c:67:19: error: ‘__dtb_start’ undeclared here (not in a function); did you mean ‘dtb_start’?
67 | void *dtb_start = __dtb_start;
| ^~~~~~~~~~~
../arch/xtensa/kernel/setup.c: In function 'xtensa_dt_io_area':
../arch/xtensa/kernel/setup.c:201:14: error: implicit declaration of function 'of_flat_dt_is_compatible'; did you mean 'of_machine_is_compatible'? [-Werror=implicit-function-declaration]
201 | if (!of_flat_dt_is_compatible(node, "simple-bus"))
../arch/xtensa/kernel/setup.c:204:18: error: implicit declaration of function 'of_get_flat_dt_prop' [-Werror=implicit-function-declaration]
204 | ranges = of_get_flat_dt_prop(node, "ranges", &len);
../arch/xtensa/kernel/setup.c:204:16: error: assignment to 'const __be32 *' {aka 'const unsigned int *'} from 'int' makes pointer from integer without a cast [-Werror=int-conversion]
204 | ranges = of_get_flat_dt_prop(node, "ranges", &len);
| ^
../arch/xtensa/kernel/setup.c: In function 'early_init_devtree':
../arch/xtensa/kernel/setup.c:228:9: error: implicit declaration of function 'early_init_dt_scan'; did you mean 'early_init_devtree'? [-Werror=implicit-function-declaration]
228 | early_init_dt_scan(params);
../arch/xtensa/kernel/setup.c:229:9: error: implicit declaration of function 'of_scan_flat_dt' [-Werror=implicit-function-declaration]
229 | of_scan_flat_dt(xtensa_dt_io_area, NULL);
xtensa-elf-ld: arch/xtensa/mm/mmu.o:(.text+0x0): undefined reference to `xtensa_kio_paddr'
Fixes: da844a8177 ("xtensa: add device trees support")
Fixes: 6cb971114f ("xtensa: remap io area defined in device tree")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb8c3a3c52 ]
Randconfig builds still show a failure for the ath5k driver,
similar to the one that was fixed for ath9k earlier:
WARNING: unmet direct dependencies detected for MAC80211_LEDS
Depends on [n]: NET [=y] && WIRELESS [=y] && MAC80211 [=y] && (LEDS_CLASS [=m]=y || LEDS_CLASS [=m]=MAC80211 [=y])
Selected by [m]:
- ATH5K [=m] && NETDEVICES [=y] && WLAN [=y] && WLAN_VENDOR_ATH [=y] && (PCI [=y] || ATH25) && MAC80211 [=y]
net/mac80211/led.c: In function 'ieee80211_alloc_led_names':
net/mac80211/led.c:34:22: error: 'struct led_trigger' has no member named 'name'
34 | local->rx_led.name = kasprintf(GFP_KERNEL, "%srx",
| ^
Copying the same logic from my ath9k patch makes this one work
as well, stubbing out the calls to the LED subsystem.
Fixes: b64acb28da ("ath9k: fix build error with LEDS_CLASS=m")
Fixes: 72cdab8087 ("ath9k: Do not select MAC80211_LEDS by default")
Fixes: 3a078876ca ("ath5k: convert LED code to use mac80211 triggers")
Link: https://lore.kernel.org/all/20210722105501.1000781-1-arnd@kernel.org/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210920122359.353810-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 450e7fe9b1 ]
Currently, it is no longer possible to retrieve a DHCP address
on the imx6qdl-pico board.
This issue has been exposed by commit f5d9aa79df ("ARM: imx6q:
remove clk-out fixup for the Atheros AR8031 and AR8035 PHYs").
Fix it by describing the qca,clk-out-frequency property as suggested
by the commit above.
Fixes: 98670a0bb0 ("ARM: dts: imx6qdl: Add imx6qdl-pico support")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c187e2eb3 ]
The MIC2025 switch input signal nEN is active low, describe it as such
in the DT. The previous change to this regulator polarity was incorrectly
influenced by broken quirks in gpiolib-of.c, which is now long fixed. So
fix this regulator polarity setting here once and for all.
Fixes: 3c3601cd6a ("ARM: dts: imx53: Update USB configuration on M53Menlo")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8c1efe14a ]
The panel already contains pinctrl-0 phandle, but it is missing
the default pinctrl-names property, so the pin configuration is
ignored. Fill in the missing pinctrl-names property, so the pin
configuration is applied.
Fixes: d81765d693 ("ARM: dts: imx53: Update LCD panel node on M53Menlo")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 833d51d7c6 ]
PT_LOAD type denotes that the segment should be loaded into the final
firmware memory region. Hash segment is not one such, because it's only
needed for PAS init and shouldn't be in the final firmware memory region.
That's why mdt_phdr_valid() explicitly reject non PT_LOAD segment and
hash segment. This actually makes the hash segment type check in
qcom_mdt_read_metadata() unnecessary and redundant. For a hash segment,
it won't be loaded into firmware memory region anyway, due to the
QCOM_MDT_TYPE_HASH check in mdt_phdr_valid(), even if it has a PT_LOAD
type for some reason (misusing or abusing?).
Some firmware files on Sony phones are such examples, e.g WCNSS firmware
of Sony Xperia M4 Aqua phone. The type of hash segment is just PT_LOAD.
Drop the unnecessary hash segment type check in qcom_mdt_read_metadata()
to fix firmware loading failure on these phones, while hash segment is
still kept away from the final firmware memory region.
Fixes: 498b98e939 ("soc: qcom: mdt_loader: Support loading non-split images")
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210828070202.7033-1-shawn.guo@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1db21c315 ]
The 28NM DSI PLL driver for msm8960 calculates with a 27MHz reference
clock and should hence use PXO, not CXO which runs at 19.2MHz.
Note that none of the DSI PHY/PLL drivers currently use this "ref"
clock; they all rely on (sometimes inexistant) global clock names and
usually function normally without a parent clock. This discrepancy will
be corrected in a future patch, for which this change needs to be in
place first.
Fixes: 6969d1d9c6 ("ARM: dts: qcom-apq8064: Set 'cxo_board' as ref clock of the DSI PHY")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Link: https://lore.kernel.org/r/20210829203027.276143-2-marijn.suijten@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e879f855e5 ]
After commit a6d90e9f22 ("bus: ti-sysc: AM3: RNG is GP only"), clang
with -Wimplicit-fallthrough enabled warns:
drivers/bus/ti-sysc.c:2958:3: warning: unannotated fall-through between
switch labels [-Wimplicit-fallthrough]
default:
^
drivers/bus/ti-sysc.c:2958:3: note: insert 'break;' to avoid
fall-through
default:
^
break;
1 warning generated.
Clang's version of this warning is a little bit more pedantic than
GCC's. Add the missing break to satisfy it to match what has been done
all over the kernel tree.
Fixes: a6d90e9f22 ("bus: ti-sysc: AM3: RNG is GP only")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9b663b34c9 upstream.
Since the LED multicolor framework support was added in commit
92a81562e6 ("leds: lp55xx: Add multicolor framework support to lp55xx")
LEDs on this platform stopped working.
Author of the framework attempted to accommodate this DT to the
framework in commit b86d3d21cd ("ARM: dts: imx6dl-yapp4: Add reg property
to the lp5562 channel node") but that is not sufficient. A color property
is now required even if the multicolor framework is not used, otherwise
the driver probe fails:
lp5562: probe of 1-0030 failed with error -22
Add the color property to fix this.
Fixes: 92a81562e6 ("leds: lp55xx: Add multicolor framework support to lp55xx")
Cc: <stable@vger.kernel.org>
Cc: linux-leds@vger.kernel.org
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2ba5acfb34 upstream.
If sd_max is unsigned, then sd_max - GSS_SEQ_WIN is a very large number
whenever sd_max is less than GSS_SEQ_WIN, and the comparison:
seq_num <= sd->sd_max - GSS_SEQ_WIN
in gss_check_seq_num is pretty much always true, even when that's
clearly not what was intended.
This was causing pynfs to hang when using krb5, because pynfs uses zero
as the initial gss sequence number. That's perfectly legal, but this
logic error causes knfsd to drop the rpc in that case. Out-of-order
sequence IDs in the first GSS_SEQ_WIN (128) calls will also cause this.
Fixes: 10b9d99a3d ("SUNRPC: Augment server-side rpcgss tracepoints")
Cc: stable@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f2e717d655 upstream.
RFC3530 notes that the 'dircount' field may be zero, in which case the
recommendation is to ignore it, and only enforce the 'maxcount' field.
In RFC5661, this recommendation to ignore a zero valued field becomes a
requirement.
Fixes: aee3776441 ("nfsd4: fix rd_dircount enforcement")
Cc: <stable@vger.kernel.org>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d625050c7 upstream.
init_nfsd() should not unregister pernet subsys if the register fails
but should instead unwind from the last successful operation which is
register_filesystem().
Unregistering a failed register_pernet_subsys() call can result in
a kernel GPF as revealed by programmatically injecting an error in
register_pernet_subsys().
Verified the fix handled failure gracefully with no lingering nfsd
entry in /proc/filesystems. This change was introduced by the commit
bd5ae9288d ("nfsd: register pernet ops last, unregister first"),
the original error handling logic was correct.
Fixes: bd5ae9288d ("nfsd: register pernet ops last, unregister first")
Cc: stable@vger.kernel.org
Signed-off-by: Patrick Ho <Patrick.Ho@netapp.com>
Acked-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1dc1eed46f upstream.
Normally the check at open time suffices, but e.g loop device does set
IOCB_DIRECT after doing its own checks (which are not sufficent for
overlayfs).
Make sure we don't call the underlying filesystem read/write method with
the IOCB_DIRECT if it's not supported.
Reported-by: Huang Jianan <huangjianan@oppo.com>
Fixes: 16914e6fc7 ("ovl: add ovl_read_iter()")
Cc: <stable@vger.kernel.org> # v4.19
Tested-by: Huang Jianan <huangjianan@oppo.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a38a4d51c upstream.
The memory at the end of the controller only accepts 32bit read/write
accesses, but the arm64 memcpy_to/fromio implementation only uses 64bit
(which will be split into two 32bit access) and 8bit leading to incomplete
copies to/from this memory when the buffer is not multiple of 8bytes.
Add a local copy using writel/readl accesses to make sure we use the right
memory access width.
The switch to memcpy_to/fromio was done because of 285133040e
("arm64: Import latest memcpy()/memmove() implementation"), but using memcpy
worked before since it mainly used 32bit memory acceses.
Fixes: 103a5348c2 ("mmc: meson-gx: use memcpy_to/fromio for dram-access-quirk")
Reported-by: Christian Hewitt <christianshewitt@gmail.com>
Suggested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210928073652.434690-1-narmstrong@baylibre.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 65a205e611 upstream.
A recent change that started reporting break events to the line
discipline caused the tty-buffer insertions to no longer be serialised
by inserting events also from the completion handler for the interrupt
endpoint.
Completion calls for distinct endpoints are not guaranteed to be
serialised. For example, in case a host-controller driver uses
bottom-half completion, the interrupt and bulk-in completion handlers
can end up running in parallel on two CPUs (high-and low-prio tasklets,
respectively) thereby breaking the tty layer's single producer
assumption.
Fix this by holding the read lock also when inserting characters from
the bulk endpoint.
Fixes: 08dff274ed ("cdc-acm: fix BREAK rx code path adding necessary calls")
Cc: stable@vger.kernel.org
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210929090937.7410-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8253a34bfa upstream.
When passing 'phys' in the devicetree to describe the USB PHY phandle
(which is the recommended way according to
Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt) the
following NULL pointer dereference is observed on i.MX7 and i.MX8MM:
[ 1.489344] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000098
[ 1.498170] Mem abort info:
[ 1.500966] ESR = 0x96000044
[ 1.504030] EC = 0x25: DABT (current EL), IL = 32 bits
[ 1.509356] SET = 0, FnV = 0
[ 1.512416] EA = 0, S1PTW = 0
[ 1.515569] FSC = 0x04: level 0 translation fault
[ 1.520458] Data abort info:
[ 1.523349] ISV = 0, ISS = 0x00000044
[ 1.527196] CM = 0, WnR = 1
[ 1.530176] [0000000000000098] user address but active_mm is swapper
[ 1.536544] Internal error: Oops: 96000044 [#1] PREEMPT SMP
[ 1.542125] Modules linked in:
[ 1.545190] CPU: 3 PID: 7 Comm: kworker/u8:0 Not tainted 5.14.0-dirty #3
[ 1.551901] Hardware name: Kontron i.MX8MM N801X S (DT)
[ 1.557133] Workqueue: events_unbound deferred_probe_work_func
[ 1.562984] pstate: 80000005 (Nzcv daif -PAN -UAO -TCO BTYPE=--)
[ 1.568998] pc : imx7d_charger_detection+0x3f0/0x510
[ 1.573973] lr : imx7d_charger_detection+0x22c/0x510
This happens because the charger functions check for the phy presence
inside the imx_usbmisc_data structure (data->usb_phy), but the chipidea
core populates the usb_phy passed via 'phys' inside 'struct ci_hdrc'
(ci->usb_phy) instead.
This causes the NULL pointer dereference inside imx7d_charger_detection().
Fix it by also searching for 'phys' in case 'fsl,usbphy' is not found.
Tested on a imx7s-warp board.
Fixes: 746f316b75 ("usb: chipidea: introduce imx7d USB charger detection")
Cc: stable@vger.kernel.org
Reported-by: Heiko Thiery <heiko.thiery@gmail.com>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210921113754.767631-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a8526a5cd upstream.
Many users are reporting that the Samsung 860 and 870 SSD are having
various issues when combined with AMD/ATI (vendor ID 0x1002) SATA
controllers and only completely disabling NCQ helps to avoid these
issues.
Always disabling NCQ for Samsung 860/870 SSDs regardless of the host
SATA adapter vendor will cause I/O performance degradation with well
behaved adapters. To limit the performance impact to ATI adapters,
introduce the ATA_HORKAGE_NO_NCQ_ON_ATI flag to force disable NCQ
only for these adapters.
Also, two libata.force parameters (noncqati and ncqati) are introduced
to disable and enable the NCQ for the system which equipped with ATI
SATA adapter and Samsung 860 and 870 SSDs. The user can determine NCQ
function to be enabled or disabled according to the demand.
After verifying the chipset from the user reports, the issue appears
on AMD/ATI SB7x0/SB8x0/SB9x0 SATA Controllers and does not appear on
recent AMD SATA adapters. The vendor ID of ATI should be 0x1002.
Therefore, ATA_HORKAGE_NO_NCQ_ON_AMD was modified to
ATA_HORKAGE_NO_NCQ_ON_ATI.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=201693
Signed-off-by: Kate Hsuan <hpa@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210903094411.58749-1-hpa@redhat.com
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Cc: Krzysztof Olędzki <ole@ans.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 02d029a41d upstream.
perf_init_event tries multiple init callbacks and does not reset the
event state between tries. When x86_pmu_event_init runs, it
unconditionally sets the destroy callback to hw_perf_event_destroy. On
the next init attempt after x86_pmu_event_init, in perf_try_init_event,
if the pmu's capabilities includes PERF_PMU_CAP_NO_EXCLUDE, the destroy
callback will be run. However, if the next init didn't set the destroy
callback, hw_perf_event_destroy will be run (since the callback wasn't
reset).
Looking at other pmu init functions, the common pattern is to only set
the destroy callback on a successful init. Resetting the callback on
failure tries to replicate that pattern.
This was discovered after commit f11dd0d805 ("perf/x86/amd/ibs: Extend
PERF_PMU_CAP_NO_EXCLUDE to IBS Op") when the second (and only second)
run of the perf tool after a reboot results in 0 samples being
generated. The extra run of hw_perf_event_destroy results in
active_events having an extra decrement on each perf run. The second run
has active_events == 0 and every subsequent run has active_events < 0.
When active_events == 0, the NMI handler will early-out and not record
any samples.
Signed-off-by: Anand K Mistry <amistry@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20210929170405.1.I078b98ee7727f9ae9d6df8262bad7e325e40faf0@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e1fc1553cd ]
Intel PMU MSRs is in msrs_to_save_all[], so add AMD PMU MSRs to have a
consistent behavior between Intel and AMD when using KVM_GET_MSRS,
KVM_SET_MSRS or KVM_GET_MSR_INDEX_LIST.
We have to add legacy and new MSRs to handle guests running without
X86_FEATURE_PERFCTR_CORE.
Signed-off-by: Fares Mehanna <faresx@amazon.de>
Message-Id: <20210915133951.22389-1-faresx@amazon.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae232ea460 ]
grow_halt_poll_ns() ignores values between 0 and
halt_poll_ns_grow_start (10000 by default). However,
when we shrink halt_poll_ns we may fall way below
halt_poll_ns_grow_start and endup with halt_poll_ns
values that don't make a lot of sense: like 1 or 9,
or 19.
VCPU1 trace (halt_poll_ns_shrink equals 2):
VCPU1 grow 10000
VCPU1 shrink 5000
VCPU1 shrink 2500
VCPU1 shrink 1250
VCPU1 shrink 625
VCPU1 shrink 312
VCPU1 shrink 156
VCPU1 shrink 78
VCPU1 shrink 39
VCPU1 shrink 19
VCPU1 shrink 9
VCPU1 shrink 4
Mirror what grow_halt_poll_ns() does and set halt_poll_ns
to 0 as soon as new shrink-ed halt_poll_ns value falls
below halt_poll_ns_grow_start.
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210902031100.252080-1-senozhatsky@chromium.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 01f91acb55 ]
The SMC64 calling convention passes a function identifier in w0 and its
parameters in x1-x17. Given this, there are two deviations in the
SMC64 call performed by the steal_time test: the function identifier is
assigned to a 64 bit register and the parameter is only 32 bits wide.
Align the call with the SMCCC by using a 32 bit register to handle the
function identifier and increasing the parameter width to 64 bits.
Suggested-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Oliver Upton <oupton@google.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-Id: <20210921171121.2148982-3-oupton@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ebaeab2fe8 ]
Idle page tracking can also be used for process address space, not only
file mappings.
Without this change, using with '-i' option for process address space
encounters below errors reported.
$ sudo ./page-types -p $(pidof bash) -i
mark page idle: Bad file descriptor
mark page idle: Bad file descriptor
mark page idle: Bad file descriptor
mark page idle: Bad file descriptor
...
Link: https://lkml.kernel.org/r/20210917032826.10669-1-changbin.du@gmail.com
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b06d893ef2 ]
Address warning:
fs/smbfs_client/smb2pdu.c:2425 create_sd_buf()
warn: struct type mismatch 'smb3_acl vs cifs_acl'
Pointed out by Dan Carpenter via smatch code analysis tool
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b78f26926b ]
Geert reported that the GIC driver locks up on a Renesas system
since 005c34ae4b ("irqchip/gic: Atomically update affinity")
fixed the driver to use writeb_relaxed() instead of writel_relaxed().
As it turns out, the interconnect used on this system mandates
32bit wide accesses for all MMIO transactions, even if the GIC
architecture specifically mandates for some registers to be byte
accessible. Gahhh...
Work around the issue by crudly detecting the offending system,
and falling back to an inefficient RMW+lock implementation.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/CAMuHMdV+Ev47K5NO8XHsanSq5YRMCHn2gWAQyV-q2LpJVy9HiQ@mail.gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fbdac19e64 ]
Setting SCSI logging level with error=3, we saw some errors from enclosues:
[108017.360833] ses 0:0:9:0: tag#641 Done: NEEDS_RETRY Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK cmd_age=0s
[108017.360838] ses 0:0:9:0: tag#641 CDB: Receive Diagnostic 1c 01 01 00 20 00
[108017.427778] ses 0:0:9:0: Power-on or device reset occurred
[108017.427784] ses 0:0:9:0: tag#641 Done: SUCCESS Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=0s
[108017.427788] ses 0:0:9:0: tag#641 CDB: Receive Diagnostic 1c 01 01 00 20 00
[108017.427791] ses 0:0:9:0: tag#641 Sense Key : Unit Attention [current]
[108017.427793] ses 0:0:9:0: tag#641 Add. Sense: Bus device reset function occurred
[108017.427801] ses 0:0:9:0: Failed to get diagnostic page 0x1
[108017.427804] ses 0:0:9:0: Failed to bind enclosure -19
[108017.427895] ses 0:0:10:0: Attached Enclosure device
[108017.427942] ses 0:0:10:0: Attached scsi generic sg18 type 13
Retry if the Send/Receive Diagnostic commands complete with a transient
error status (NOT_READY or UNIT_ATTENTION with ASC 0x29).
Link: https://lore.kernel.org/r/1631849061-10210-2-git-send-email-wenxiong@linux.ibm.com
Reviewed-by: Brian King <brking@linux.ibm.com>
Reviewed-by: James Bottomley <jejb@linux.ibm.com>
Signed-off-by: Wen Xiong <wenxiong@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5445dae29 ]
To avoid race between time out and tear down, in tear down process,
first we quiesce the queue, and then delete the timer and cancel
the time out work for the queue.
This patch merges the admin and io sync ops into the queue teardown logic
as shown in the RDMA patch 3017013dcc "nvme-rdma: avoid race between time
out and tear down". There is no teardown_lock in nvme-fc.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Tested-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 555f66d0f8 ]
In case the number of hardware queues changes, we need to update the
tagset and the mapping of ctx to hctx first.
If we try to create and connect the I/O queues first, this operation
will fail (target will reject the connect call due to the wrong number
of queues) and hence we bail out of the recreate function. Then we
will to try the very same operation again, thus we don't make any
progress.
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39a71f712d ]
Fix get_warnings_count() to check fscanf() return value to get rid
of the following warning:
x86_64/mmio_warning_test.c: In function ‘get_warnings_count’:
x86_64/mmio_warning_test.c:85:2: warning: ignoring return value of ‘fscanf’ declared with attribute ‘warn_unused_result’ [-Wunused-result]
85 | fscanf(f, "%d", &warnings);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8914a7a247 ]
LKP/0Day reported some building errors about kvm, and errors message
are not always same:
- lib/x86_64/processor.c:1083:31: error: ‘KVM_CAP_NESTED_STATE’ undeclared
(first use in this function); did you mean ‘KVM_CAP_PIT_STATE2’?
- lib/test_util.c:189:30: error: ‘MAP_HUGE_16KB’ undeclared (first use
in this function); did you mean ‘MAP_HUGE_16GB’?
Although kvm relies on the khdr, they still be built in parallel when -j
is specified. In this case, it will cause compiling errors.
Here we mark target khdr as NOTPARALLEL to make it be always built
first.
CC: Philip Li <philip.li@intel.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a5ff77bf0 ]
Couple of fixes to the LBW RR configuration:
1. Add missing configuration of the SM RR registers in the DMA_IF.
2. Remove HBW range that doesn't belong.
3. Add entire gap + DBG area, from end of TPC7 to end of entire
DBG space.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f81c08f897 ]
testusb' application which uses 'usbtest' driver reports 'unknown speed'
from the function 'find_testdev'. The variable 'entry->speed' was not
updated from the application. The IOCTL mentioned in the FIXME comment can
only report whether the connection is low speed or not. Speed is read using
the IOCTL USBDEVFS_GET_SPEED which reports the proper speed grade. The
call is implemented in the function 'handle_testdev' where the file
descriptor was availble locally. Sample output is given below where 'high
speed' is printed as the connected speed.
sudo ./testusb -a
high speed /dev/bus/usb/001/011 0
/dev/bus/usb/001/011 test 0, 0.000015 secs
/dev/bus/usb/001/011 test 1, 0.194208 secs
/dev/bus/usb/001/011 test 2, 0.077289 secs
/dev/bus/usb/001/011 test 3, 0.170604 secs
/dev/bus/usb/001/011 test 4, 0.108335 secs
/dev/bus/usb/001/011 test 5, 2.788076 secs
/dev/bus/usb/001/011 test 6, 2.594610 secs
/dev/bus/usb/001/011 test 7, 2.905459 secs
/dev/bus/usb/001/011 test 8, 2.795193 secs
/dev/bus/usb/001/011 test 9, 8.372651 secs
/dev/bus/usb/001/011 test 10, 6.919731 secs
/dev/bus/usb/001/011 test 11, 16.372687 secs
/dev/bus/usb/001/011 test 12, 16.375233 secs
/dev/bus/usb/001/011 test 13, 2.977457 secs
/dev/bus/usb/001/011 test 14 --> 22 (Invalid argument)
/dev/bus/usb/001/011 test 17, 0.148826 secs
/dev/bus/usb/001/011 test 18, 0.068718 secs
/dev/bus/usb/001/011 test 19, 0.125992 secs
/dev/bus/usb/001/011 test 20, 0.127477 secs
/dev/bus/usb/001/011 test 21 --> 22 (Invalid argument)
/dev/bus/usb/001/011 test 24, 4.133763 secs
/dev/bus/usb/001/011 test 27, 2.140066 secs
/dev/bus/usb/001/011 test 28, 2.120713 secs
/dev/bus/usb/001/011 test 29, 0.507762 secs
Signed-off-by: Faizel K B <faizel.kb@dicortech.com>
Link: https://lore.kernel.org/r/20210902114444.15106-1-faizel.kb@dicortech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 372d1f3e1b ]
The ext2_error() function syncs the filesystem so it sleeps. The caller
is holding a spinlock so it's not allowed to sleep.
ext2_statfs() <- disables preempt
-> ext2_count_free_blocks()
-> ext2_get_group_desc()
Fix this by using WARN() to print an error message and a stack trace
instead of using ext2_error().
Link: https://lore.kernel.org/r/20210921203233.GA16529@kili
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ede7f84c7 ]
When re-entering the main loop of xenvif_tx_check_gop() a 2nd time, the
special considerations for the head of the SKB no longer apply. Don't
mistakenly report ERROR to the frontend for the first entry in the list,
even if - from all I can tell - this shouldn't matter much as the overall
transmit will need to be considered failed anyway.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf9579976f ]
MDIO-attached devices might have interrupts and other things that might
need quiesced when we kexec into a new kernel. Things are even more
creepy when those interrupt lines are shared, and in that case it is
absolutely mandatory to disable all interrupt sources.
Moreover, MDIO devices might be DSA switches, and DSA needs its own
shutdown method to unlink from the DSA master, which is a new
requirement that appeared after commit 2f1e8ea726 ("net: dsa: link
interfaces with the DSA master to get rid of lockdep warnings").
So introduce a ->shutdown method in the MDIO device driver structure.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b225baaba ]
When we get an error flushing one device, during a super block commit, we
record the error in the device structure, in the field 'last_flush_error'.
This is used to later check if we should error out the super block commit,
depending on whether the number of flush errors is greater than or equals
to the maximum tolerated device failures for a raid profile.
However if we get a transient device flush error, unmount the filesystem
and later try to mount it, we can fail the mount because we treat that
past error as critical and consider the device is missing. Even if it's
very likely that the error will happen again, as it's probably due to a
hardware related problem, there may be cases where the error might not
happen again. One example is during testing, and a test case like the
new generic/648 from fstests always triggers this. The test cases
generic/019 and generic/475 also trigger this scenario, but very
sporadically.
When this happens we get an error like this:
$ mount /dev/sdc /mnt
mount: /mnt wrong fs type, bad option, bad superblock on /dev/sdc, missing codepage or helper program, or other error.
$ dmesg
(...)
[12918.886926] BTRFS warning (device sdc): chunk 13631488 missing 1 devices, max tolerance is 0 for writable mount
[12918.888293] BTRFS warning (device sdc): writable mount is not allowed due to too many missing devices
[12918.890853] BTRFS error (device sdc): open_ctree failed
The failure happens because when btrfs_check_rw_degradable() is called at
mount time, or at remount from RO to RW time, is sees a non zero value in
a device's ->last_flush_error attribute, and therefore considers that the
device is 'missing'.
Fix this by setting a device's ->last_flush_error to zero when we close a
device, making sure the error is not seen on the next mount attempt. We
only need to track flush errors during the current mount, so that we never
commit a super block if such errors happened.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bbc9a6eb5e ]
There is a BUG_ON() in btrfs_csum_one_bio() to catch code logic error.
It has indeed caught several bugs during subpage development.
But the BUG_ON() itself will bring down the whole system which is
an overkill.
Replace it with a WARN() and exit gracefully, so that it won't crash the
whole system while we can still catch the code logic error.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02579b2ff8 ]
When the back channel enters SEQ4_STATUS_CB_PATH_DOWN state, the client
recovers by sending BIND_CONN_TO_SESSION but the server fails to recover
the back channel and leaves it as NFSD4_CB_DOWN.
Fix by enhancing nfsd4_bind_conn_to_session to probe the back channel
by calling nfsd4_probe_callback.
Signed-off-by: Dai Ngo <dai.ngo@oracle.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 196159d278 ]
Add info for getting the firmware directly from the UEFI for the Chuwi Hi10
Plus (CWI527), so that the user does not need to manually install the
firmware in /lib/firmware/silead.
This change will make the touchscreen on these devices work OOTB,
without requiring any manual setup.
Also tweak the min and width/height values a bit for more accurate position
reporting.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210905130210.32810-2-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3bf1669b0e ]
Add touchscreen info for the Chuwi HiBook (CWI514) tablet. This includes
info for getting the firmware directly from the UEFI, so that the user does
not need to manually install the firmware in /lib/firmware/silead.
This change will make the touchscreen on these devices work OOTB,
without requiring any manual setup.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210905130210.32810-1-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5457773ef9 ]
Previously zero length transfers submitted to the Rokchip SPI driver would
time out in the SPI layer. This happens because the SPI peripheral does
not trigger a transfer completion interrupt for zero length transfers.
Fix that by completing zero length transfers immediately at start of
transfer.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Link: https://lore.kernel.org/r/20210827050357.165409-1-t.schramm@manjaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
This is a copy of the code and approach from our DAC+ driver.
It allows to probe (and activate) an optional TPA6130A2 headphone
amplifier. Updated email address.
Signed-off-by: Joerg Schambacher <joerg@hifiberry.com>
This is a copy of the approach from our DAC+ driver.
It allows to probe (and activate) an optional TPA6130A2 headphone
amplifier.
Signed-off-by: Joerg Schambacher <joerg@hifiberry.com>
A regression introduced in https://github.com/raspberrypi/linux/pull/3887
meant that if the newly scheduled transfer immediately returned data, and
the driver resubmitted a single URB after every transfer, then the effective
polling interval would end up being approx 1ms.
Use the larger of SCHEDULE_SLOP or the configured endpoint interval.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
commit e9edc188fc upstream.
Syzbot was able to trigger the following warning [1]
No repro found by syzbot yet but I was able to trigger similar issue
by having 2 scripts running in parallel, changing conntrack hash sizes,
and:
for j in `seq 1 1000` ; do unshare -n /bin/true >/dev/null ; done
It would take more than 5 minutes for net_namespace structures
to be cleaned up.
This is because nf_ct_iterate_cleanup() has to restart everytime
a resize happened.
By adding a mutex, we can serialize hash resizes and cleanups
and also make get_next_corpse() faster by skipping over empty
buckets.
Even without resizes in the picture, this patch considerably
speeds up network namespace dismantles.
[1]
INFO: task syz-executor.0:8312 can't die for more than 144 seconds.
task:syz-executor.0 state:R running task stack:25672 pid: 8312 ppid: 6573 flags:0x00004006
Call Trace:
context_switch kernel/sched/core.c:4955 [inline]
__schedule+0x940/0x26f0 kernel/sched/core.c:6236
preempt_schedule_common+0x45/0xc0 kernel/sched/core.c:6408
preempt_schedule_thunk+0x16/0x18 arch/x86/entry/thunk_64.S:35
__local_bh_enable_ip+0x109/0x120 kernel/softirq.c:390
local_bh_enable include/linux/bottom_half.h:32 [inline]
get_next_corpse net/netfilter/nf_conntrack_core.c:2252 [inline]
nf_ct_iterate_cleanup+0x15a/0x450 net/netfilter/nf_conntrack_core.c:2275
nf_conntrack_cleanup_net_list+0x14c/0x4f0 net/netfilter/nf_conntrack_core.c:2469
ops_exit_list+0x10d/0x160 net/core/net_namespace.c:171
setup_net+0x639/0xa30 net/core/net_namespace.c:349
copy_net_ns+0x319/0x760 net/core/net_namespace.c:470
create_new_namespaces+0x3f6/0xb20 kernel/nsproxy.c:110
unshare_nsproxy_namespaces+0xc1/0x1f0 kernel/nsproxy.c:226
ksys_unshare+0x445/0x920 kernel/fork.c:3128
__do_sys_unshare kernel/fork.c:3202 [inline]
__se_sys_unshare kernel/fork.c:3200 [inline]
__x64_sys_unshare+0x2d/0x40 kernel/fork.c:3200
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f63da68e739
RSP: 002b:00007f63d7c05188 EFLAGS: 00000246 ORIG_RAX: 0000000000000110
RAX: ffffffffffffffda RBX: 00007f63da792f80 RCX: 00007f63da68e739
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000040000000
RBP: 00007f63da6e8cc4 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f63da792f80
R13: 00007fff50b75d3f R14: 00007f63d7c05300 R15: 0000000000022000
Showing all locks held in the system:
1 lock held by khungtaskd/27:
#0: ffffffff8b980020 (rcu_read_lock){....}-{1:2}, at: debug_show_all_locks+0x53/0x260 kernel/locking/lockdep.c:6446
2 locks held by kworker/u4:2/153:
#0: ffff888010c69138 ((wq_completion)events_unbound){+.+.}-{0:0}, at: arch_atomic64_set arch/x86/include/asm/atomic64_64.h:34 [inline]
#0: ffff888010c69138 ((wq_completion)events_unbound){+.+.}-{0:0}, at: arch_atomic_long_set include/linux/atomic/atomic-long.h:41 [inline]
#0: ffff888010c69138 ((wq_completion)events_unbound){+.+.}-{0:0}, at: atomic_long_set include/linux/atomic/atomic-instrumented.h:1198 [inline]
#0: ffff888010c69138 ((wq_completion)events_unbound){+.+.}-{0:0}, at: set_work_data kernel/workqueue.c:634 [inline]
#0: ffff888010c69138 ((wq_completion)events_unbound){+.+.}-{0:0}, at: set_work_pool_and_clear_pending kernel/workqueue.c:661 [inline]
#0: ffff888010c69138 ((wq_completion)events_unbound){+.+.}-{0:0}, at: process_one_work+0x896/0x1690 kernel/workqueue.c:2268
#1: ffffc9000140fdb0 ((kfence_timer).work){+.+.}-{0:0}, at: process_one_work+0x8ca/0x1690 kernel/workqueue.c:2272
1 lock held by systemd-udevd/2970:
1 lock held by in:imklog/6258:
#0: ffff88807f970ff0 (&f->f_pos_lock){+.+.}-{3:3}, at: __fdget_pos+0xe9/0x100 fs/file.c:990
3 locks held by kworker/1:6/8158:
1 lock held by syz-executor.0/8312:
2 locks held by kworker/u4:13/9320:
1 lock held by syz-executor.5/10178:
1 lock held by syz-executor.4/10217:
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7661809d49 upstream.
'kvmalloc()' is a convenience function for people who want to do a
kmalloc() but fall back on vmalloc() if there aren't enough physically
contiguous pages, or if the allocation is larger than what kmalloc()
supports.
However, let's make sure it doesn't get _too_ easy to do crazy things
with it. In particular, don't allow big allocations that could be due
to integer overflow or underflow. So make sure the allocation size fits
in an 'int', to protect against trivial integer conversion issues.
Acked-by: Willy Tarreau <w@1wt.eu>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 505d9dcb0f upstream.
There are three bugs in this code:
1) If we ccp_init_data() fails for &src then we need to free aad.
Use goto e_aad instead of goto e_ctx.
2) The label to free the &final_wa was named incorrectly as "e_tag" but
it should have been "e_final_wa". One error path leaked &final_wa.
3) The &tag was leaked on one error path. In that case, I added a free
before the goto because the resource was local to that block.
Fixes: 36cf515b9b ("crypto: ccp - Enable support for AES GCM on v5 CCPs")
Reported-by: "minihanshen(沈明航)" <minihanshen@tencent.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: John Allen <john.allen@amd.com>
Tested-by: John Allen <john.allen@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dcb713d53e upstream.
There are two invocation sites of hso_free_net_device. After
refactoring hso_create_net_device, this parameter is useless.
Remove the bailout in the hso_free_net_device and change the invocation
sites of this function.
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[Backport this cleanup patch to 5.10 and 5.14 in order to keep the
codebase consistent with the 4.14/4.19/5.4 patchseries]
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a9f5970767 upstream.
up->corkflag field can be read or written without any lock.
Annotate accesses to avoid possible syzbot/KCSAN reports.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22d65765f2 upstream.
Since the actual_length calculation is performed unsigned, packets
shorter than 7 bytes (e.g. packets without data or otherwise truncated)
or non-received packets ("zero" bytes) can cause buffer overflow.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=214437
Fixes: 42337b9d4d958("HID: add driver for U2F Zero built-in LED and RNG")
Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42cb447410 upstream.
When ext4_htree_fill_tree() fails, ext4_dx_readdir() can run into an
infinite loop since if info->last_pos != ctx->pos this will reset the
directory scan and reread the failing entry. For example:
1. a dx_dir which has 3 block, block 0 as dx_root block, block 1/2 as
leaf block which own the ext4_dir_entry_2
2. block 1 read ok and call_filldir which will fill the dirent and update
the ctx->pos
3. block 2 read fail, but we has already fill some dirent, so we will
return back to userspace will a positive return val(see ksys_getdents64)
4. the second ext4_dx_readdir will reset the world since info->last_pos
!= ctx->pos, and will also init the curr_hash which pos to block 1
5. So we will read block1 too, and once block2 still read fail, we can
only fill one dirent because the hash of the entry in block1(besides
the last one) won't greater than curr_hash
6. this time, we forget update last_pos too since the read for block2
will fail, and since we has got the one entry, ksys_getdents64 can
return success
7. Latter we will trapped in a loop with step 4~6
Cc: stable@kernel.org
Signed-off-by: yangerkun <yangerkun@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Link: https://lore.kernel.org/r/20210914111415.3921954-1-yangerkun@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1fd95c05d8 upstream.
If the call to ext4_map_blocks() fails due to an corrupted file
system, ext4_ext_replay_set_iblocks() can get stuck in an infinite
loop. This could be reproduced by running generic/526 with a file
system that has inline_data and fast_commit enabled. The system will
repeatedly log to the console:
EXT4-fs warning (device dm-3): ext4_block_to_path:105: block 1074800922 > max in inode 131076
and the stack that it gets stuck in is:
ext4_block_to_path+0xe3/0x130
ext4_ind_map_blocks+0x93/0x690
ext4_map_blocks+0x100/0x660
skip_hole+0x47/0x70
ext4_ext_replay_set_iblocks+0x223/0x440
ext4_fc_replay_inode+0x29e/0x3b0
ext4_fc_replay+0x278/0x550
do_one_pass+0x646/0xc10
jbd2_journal_recover+0x14a/0x270
jbd2_journal_load+0xc4/0x150
ext4_load_journal+0x1f3/0x490
ext4_fill_super+0x22d4/0x2c00
With this patch, generic/526 still fails, but system is no longer
locking up in a tight loop. It's likely the root casue is that
fast_commit replay is corrupting file systems with inline_data, and we
probably need to add better error handling in the fast commit replay
code path beyond what is done here, which essentially just breaks the
infinite loop without reporting the to the higher levels of the code.
Fixes: 8016E29F4362 ("ext4: fast commit recovery path")
Cc: stable@kernel.org
Cc: Harshad Shirwadkar <harshadshirwadkar@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6fed83957f upstream.
When ext4_insert_delayed block receives and recovers from an error from
ext4_es_insert_delayed_block(), e.g., ENOMEM, it does not release the
space it has reserved for that block insertion as it should. One effect
of this bug is that s_dirtyclusters_counter is not decremented and
remains incorrectly elevated until the file system has been unmounted.
This can result in premature ENOSPC returns and apparent loss of free
space.
Another effect of this bug is that
/sys/fs/ext4/<dev>/delayed_allocation_blocks can remain non-zero even
after syncfs has been executed on the filesystem.
Besides, add check for s_dirtyclusters_counter when inode is going to be
evicted and freed. s_dirtyclusters_counter can still keep non-zero until
inode is written back in .evict_inode(), and thus the check is delayed
to .destroy_inode().
Fixes: 51865fda28 ("ext4: let ext4 maintain extent status tree")
Cc: stable@kernel.org
Suggested-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Jeffle Xu <jefflexu@linux.alibaba.com>
Reviewed-by: Eric Whitney <enwlinux@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Link: https://lore.kernel.org/r/20210823061358.84473-1-jefflexu@linux.alibaba.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a2c2f0826e upstream.
Now EXT4_FC_TAG_ADD_RANGE uses ext4_extent to track the
newly-added blocks, but the limit on the max value of
ee_len field is ignored, and it can lead to BUG_ON as
shown below when running command "fallocate -l 128M file"
on a fast_commit-enabled fs:
kernel BUG at fs/ext4/ext4_extents.h:199!
invalid opcode: 0000 [#1] SMP PTI
CPU: 3 PID: 624 Comm: fallocate Not tainted 5.14.0-rc6+ #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996)
RIP: 0010:ext4_fc_write_inode_data+0x1f3/0x200
Call Trace:
? ext4_fc_write_inode+0xf2/0x150
ext4_fc_commit+0x93b/0xa00
? ext4_fallocate+0x1ad/0x10d0
ext4_sync_file+0x157/0x340
? ext4_sync_file+0x157/0x340
vfs_fsync_range+0x49/0x80
do_fsync+0x3d/0x70
__x64_sys_fsync+0x14/0x20
do_syscall_64+0x3b/0xc0
entry_SYSCALL_64_after_hwframe+0x44/0xae
Simply fixing it by limiting the number of blocks
in one EXT4_FC_TAG_ADD_RANGE TLV.
Fixes: aa75f4d3da ("ext4: main fast-commit commit path")
Cc: stable@kernel.org
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Link: https://lore.kernel.org/r/20210820044505.474318-1-houtao1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 75ca6ad408 upstream.
We should use unsigned long long rather than loff_t to avoid
overflow in ext4_max_bitmap_size() for comparison before returning.
w/o this patch sbi->s_bitmap_maxbytes was becoming a negative
value due to overflow of upper_limit (with has_huge_files as true)
Below is a quick test to trigger it on a 64KB pagesize system.
sudo mkfs.ext4 -b 65536 -O ^has_extents,^64bit /dev/loop2
sudo mount /dev/loop2 /mnt
sudo echo "hello" > /mnt/hello -> This will error out with
"echo: write error: File too large"
Signed-off-by: Ritesh Harjani <riteshh@linux.ibm.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Link: https://lore.kernel.org/r/594f409e2c543e90fd836b78188dfa5c575065ba.1622867594.git.riteshh@linux.ibm.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a89936cce8 upstream.
The tty driver name is used also after registering the driver and must
specifically not be allocated on the stack to avoid leaking information
to user space (or triggering an oops).
Drivers should not try to encode topology information in the tty device
name but this one snuck in through staging without anyone noticing and
another driver has since copied this malpractice.
Fixing the ABI is a separate issue, but this at least plugs the security
hole.
Fixes: ba4dc61fe8 ("Staging: ipack: add support for IP-OCTAL mezzanine board")
Cc: stable@vger.kernel.org # 3.5
Acked-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210917114622.5412-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b2f72cc0a upstream.
In commit b212921b13 ("elf: don't use MAP_FIXED_NOREPLACE for elf
executable mappings") we still leave MAP_FIXED_NOREPLACE in place for
load_elf_interp.
Unfortunately, this will cause kernel to fail to start with:
1 (init): Uhuuh, elf segment at 00003ffff7ffd000 requested but the memory is mapped already
Failed to execute /init (error -17)
The reason is that the elf interpreter (ld.so) has overlapping segments.
readelf -l ld-2.31.so
Program Headers:
Type Offset VirtAddr PhysAddr
FileSiz MemSiz Flags Align
LOAD 0x0000000000000000 0x0000000000000000 0x0000000000000000
0x000000000002c94c 0x000000000002c94c R E 0x10000
LOAD 0x000000000002dae0 0x000000000003dae0 0x000000000003dae0
0x00000000000021e8 0x0000000000002320 RW 0x10000
LOAD 0x000000000002fe00 0x000000000003fe00 0x000000000003fe00
0x00000000000011ac 0x0000000000001328 RW 0x10000
The reason for this problem is the same as described in commit
ad55eac74f ("elf: enforce MAP_FIXED on overlaying elf segments").
Not only executable binaries, elf interpreters (e.g. ld.so) can have
overlapping elf segments, so we better drop MAP_FIXED_NOREPLACE and go
back to MAP_FIXED in load_elf_interp.
Fixes: 4ed2863951 ("fs, elf: drop MAP_FIXED usage from elf_map")
Cc: <stable@vger.kernel.org> # v4.19
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Hocko <mhocko@suse.com>
Signed-off-by: Chen Jingwen <chenjingwen6@huawei.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 35306eb238 ]
Jann Horn reported that SO_PEERCRED and SO_PEERGROUPS implementations
are racy, as af_unix can concurrently change sk_peer_pid and sk_peer_cred.
In order to fix this issue, this patch adds a new spinlock that needs
to be used whenever these fields are read or written.
Jann also pointed out that l2cap_sock_get_peer_pid_cb() is currently
reading sk->sk_peer_pid which makes no sense, as this field
is only possibly set by AF_UNIX sockets.
We will have to clean this in a separate patch.
This could be done by reverting b48596d1dc "Bluetooth: L2CAP: Add get_peer_pid callback"
or implementing what was truly expected.
Fixes: 109f6e39fa ("af_unix: Allow SO_PEERCRED to work across namespaces.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jann Horn <jannh@google.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d88fd1b546 ]
When EEE support was added to the 28nm EPHY it was assumed that it would
be able to support the standard clause 45 over clause 22 register access
method. It turns out that the PHY does not support that, which is the
very reason for using the indirect shadow mode 2 bank 3 access method.
Implement {read,write}_mmd to allow the standard PHY library routines
pertaining to EEE querying and configuration to work correctly on these
PHYs. This forces us to implement a __phy_set_clr_bits() function that
does not grab the MDIO bus lock since the PHY driver's {read,write}_mmd
functions are always called with that lock held.
Fixes: 83ee102a69 ("net: phy: bcm7xxx: add support for 28nm EPHY")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27bf4af69f ]
Currently, the rx vlan filter will always be disabled before selftest and
be enabled after selftest as the rx vlan filter feature is fixed on in
old device earlier than V3.
However, this feature is not fixed in some new devices and it can be
disabled by user. In this case, it is wrong if rx vlan filter is enabled
after selftest. So fix it.
Fixes: bcc26e8dc4 ("net: hns3: remove unused code in hns3_self_test()")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 108b3c7810 ]
Currently, if function adds an existing unicast mac address, eventhough
driver will not add this address into hardware, but it will return 0 in
function hclge_add_uc_addr_common(). It will cause the state of this
unicast mac address is ACTIVE in driver, but it should be in TO-ADD state.
To fix this problem, function hclge_add_uc_addr_common() returns -EEXIST
if mac address is existing, and delete two error log to avoid printing
them all the time after this modification.
Fixes: 72110b5674 ("net: hns3: return 0 and print warning when hit duplicate MAC")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0472e95ffe ]
HCLGE_FLAG_MQPRIO_ENABLE is supposed to set when enable
multiple TCs with tc mqprio, and HCLGE_FLAG_DCB_ENABLE is
supposed to set when enable multiple TCs with ets. But
the driver mixed the flags when updating the tm configuration.
Furtherly, PFC should be available when HCLGE_FLAG_MQPRIO_ENABLE
too, so remove the unnecessary limitation.
Fixes: 5a5c909174 ("net: hns3: add support for tc mqprio offload")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d78e5b6a67 ]
Bellow HNAE3_DEVICE_VERSION_V3, MAC pause mode just support one
TC, when enabled multiple TCs, force enable PFC mode.
HNAE3_DEVICE_VERSION_V3 can support MAC pause mode on multiple
TCs, so when enable multiple TCs, just keep MAC pause mode,
and enable PFC mode just according to the user settings.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 513e605d7a ]
The ixgbe driver currently generates a NULL pointer dereference with
some machine (online cpus < 63). This is due to the fact that the
maximum value of num_xdp_queues is nr_cpu_ids. Code is in
"ixgbe_set_rss_queues"".
Here's how the problem repeats itself:
Some machine (online cpus < 63), And user set num_queues to 63 through
ethtool. Code is in the "ixgbe_set_channels",
adapter->ring_feature[RING_F_FDIR].limit = count;
It becomes 63.
When user use xdp, "ixgbe_set_rss_queues" will set queues num.
adapter->num_rx_queues = rss_i;
adapter->num_tx_queues = rss_i;
adapter->num_xdp_queues = ixgbe_xdp_queues(adapter);
And rss_i's value is from
f = &adapter->ring_feature[RING_F_FDIR];
rss_i = f->indices = f->limit;
So "num_rx_queues" > "num_xdp_queues", when run to "ixgbe_xdp_setup",
for (i = 0; i < adapter->num_rx_queues; i++)
if (adapter->xdp_ring[i]->xsk_umem)
It leads to panic.
Call trace:
[exception RIP: ixgbe_xdp+368]
RIP: ffffffffc02a76a0 RSP: ffff9fe16202f8d0 RFLAGS: 00010297
RAX: 0000000000000000 RBX: 0000000000000020 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 000000000000001c RDI: ffffffffa94ead90
RBP: ffff92f8f24c0c18 R8: 0000000000000000 R9: 0000000000000000
R10: ffff9fe16202f830 R11: 0000000000000000 R12: ffff92f8f24c0000
R13: ffff9fe16202fc01 R14: 000000000000000a R15: ffffffffc02a7530
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
7 [ffff9fe16202f8f0] dev_xdp_install at ffffffffa89fbbcc
8 [ffff9fe16202f920] dev_change_xdp_fd at ffffffffa8a08808
9 [ffff9fe16202f960] do_setlink at ffffffffa8a20235
10 [ffff9fe16202fa88] rtnl_setlink at ffffffffa8a20384
11 [ffff9fe16202fc78] rtnetlink_rcv_msg at ffffffffa8a1a8dd
12 [ffff9fe16202fcf0] netlink_rcv_skb at ffffffffa8a717eb
13 [ffff9fe16202fd40] netlink_unicast at ffffffffa8a70f88
14 [ffff9fe16202fd80] netlink_sendmsg at ffffffffa8a71319
15 [ffff9fe16202fdf0] sock_sendmsg at ffffffffa89df290
16 [ffff9fe16202fe08] __sys_sendto at ffffffffa89e19c8
17 [ffff9fe16202ff30] __x64_sys_sendto at ffffffffa89e1a64
18 [ffff9fe16202ff38] do_syscall_64 at ffffffffa84042b9
19 [ffff9fe16202ff50] entry_SYSCALL_64_after_hwframe at ffffffffa8c0008c
So I fix ixgbe_max_channels so that it will not allow a setting of queues
to be higher than the num_online_cpus(). And when run to ixgbe_xdp_setup,
take the smaller value of num_rx_queues and num_xdp_queues.
Fixes: 4a9b32f30f ("ixgbe: fix potential RX buffer starvation for AF_XDP")
Signed-off-by: Feng Zhou <zhoufeng.zf@bytedance.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79a7482249 ]
Both cxgb4 and csiostor drivers run on their own independent Physical
Function. But when cxgb4 and csiostor are both being loaded in parallel via
modprobe, there is a race when firmware upgrade is attempted by both the
drivers.
When the cxgb4 driver initiates the firmware upgrade, it halts the firmware
and the chip until upgrade is complete. When the csiostor driver is coming
up in parallel, the firmware mailbox communication fails with timeouts and
the csiostor driver probe fails.
Add a module soft dependency on cxgb4 driver to ensure loading csiostor
triggers cxgb4 to load first when available to avoid the firmware upgrade
race.
Link: https://lore.kernel.org/r/1632759248-15382-1-git-send-email-rahul.lakkireddy@chelsio.com
Fixes: a3667aaed5 ("[SCSI] csiostor: Chelsio FCoE offload driver")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ebc69e897e ]
This reverts commit 2d52c58b9c.
We have had several folks complain that this causes hangs for them, which
is especially problematic as the commit has also hit stable already.
As no resolution seems to be forthcoming right now, revert the patch.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=214503
Fixes: 2d52c58b9c ("block, bfq: honor already-setup queue merges")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51bb08dd04 ]
An object file cannot be built for both loadable module and built-in
use at the same time:
arm-linux-gnueabi-ld: drivers/net/ethernet/micrel/ks8851_common.o: in function `ks8851_probe_common':
ks8851_common.c:(.text+0xf80): undefined reference to `__this_module'
Change the ks8851_common code to be a standalone module instead,
and use Makefile logic to ensure this is built-in if at least one
of its two users is.
Fixes: 797047f875 ("net: ks8851: Implement Parallel bus operations")
Link: https://lore.kernel.org/netdev/20210125121937.3900988-1-arnd@kernel.org/
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d888eaac4f ]
When building bpf selftest with make -j, I'm randomly getting build failures
such as this one:
In file included from progs/bpf_flow.c:19:
[...]/tools/testing/selftests/bpf/tools/include/bpf/bpf_helpers.h:11:10: fatal error: 'bpf_helper_defs.h' file not found
#include "bpf_helper_defs.h"
^~~~~~~~~~~~~~~~~~~
The file that fails the build varies between runs but it's always in the
progs/ subdir.
The reason is a missing make dependency on libbpf for the .o files in
progs/. There was a dependency before commit 3ac2e20fba but that commit
removed it to prevent unneeded rebuilds. However, that only works if libbpf
has been built already; the 'wildcard' prerequisite does not trigger when
there's no bpf_helper_defs.h generated yet.
Keep the libbpf as an order-only prerequisite to satisfy both goals. It is
always built before the progs/ objects but it does not trigger unnecessary
rebuilds by itself.
Fixes: 3ac2e20fba ("selftests/bpf: BPF object files should depend only on libbpf headers")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/ee84ab66436fba05a197f952af23c98d90eb6243.1632758415.git.jbenc@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a98ae12fb ]
When introducing CAP_BPF, bpf_jit_charge_modmem() was not changed to treat
programs with CAP_BPF as privileged for the purpose of JIT memory allocation.
This means that a program without CAP_BPF can block a program with CAP_BPF
from loading a program.
Fix this by checking bpf_capable() in bpf_jit_charge_modmem().
Fixes: 2c78ee898d ("bpf: Implement CAP_BPF")
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210922111153.19843-1-lmb@cloudflare.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51032e6f17 ]
The e100_get_regs function is used to implement a simple register dump
for the e100 device. The data is broken into a couple of MAC control
registers, and then a series of PHY registers, followed by a memory dump
buffer.
The total length of the register dump is defined as (1 + E100_PHY_REGS)
* sizeof(u32) + sizeof(nic->mem->dump_buf).
The logic for filling in the PHY registers uses a convoluted inverted
count for loop which counts from E100_PHY_REGS (0x1C) down to 0, and
assigns the slots 1 + E100_PHY_REGS - i. The first loop iteration will
fill in [1] and the final loop iteration will fill in [1 + 0x1C]. This
is actually one more than the supposed number of PHY registers.
The memory dump buffer is then filled into the space at
[2 + E100_PHY_REGS] which will cause that memcpy to assign 4 bytes past
the total size.
The end result is that we overrun the total buffer size allocated by the
kernel, which could lead to a panic or other issues due to memory
corruption.
It is difficult to determine the actual total number of registers
here. The only 8255x datasheet I could find indicates there are 28 total
MDI registers. However, we're reading 29 here, and reading them in
reverse!
In addition, the ethtool e100 register dump interface appears to read
the first PHY register to determine if the device is in MDI or MDIx
mode. This doesn't appear to be documented anywhere within the 8255x
datasheet. I can only assume it must be in register 28 (the extra
register we're reading here).
Lets not change any of the intended meaning of what we copy here. Just
extend the space by 4 bytes to account for the extra register and
continue copying the data out in the same order.
Change the E100_PHY_REGS value to be the correct total (29) so that the
total register dump size is calculated properly. Fix the offset for
where we copy the dump buffer so that it doesn't overrun the total size.
Re-write the for loop to use counting up instead of the convoluted
down-counting. Correct the mdio_read offset to use the 0-based register
offsets, but maintain the bizarre reverse ordering so that we have the
ABI expected by applications like ethtool. This requires and additional
subtraction of 1. It seems a bit odd but it makes the flow of assignment
into the register buffer easier to follow.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Felicitas Hetzelt <felicitashetzelt@gmail.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4329c8dc11 ]
commit abf9b90205 ("e100: cleanup unneeded math") tried to simplify
e100_get_regs_len and remove a double 'divide and then multiply'
calculation that the e100_reg_regs_len function did.
This change broke the size calculation entirely as it failed to account
for the fact that the numbered registers are actually 4 bytes wide and
not 1 byte. This resulted in a significant under allocation of the
register buffer used by e100_get_regs.
Fix this by properly multiplying the register count by u32 first before
adding the size of the dump buffer.
Fixes: abf9b90205 ("e100: cleanup unneeded math")
Reported-by: Felicitas Hetzelt <felicitashetzelt@gmail.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b9c587fed6 ]
Same members of the Marvell Ethernet switches impose MTU restrictions
on ports used for connecting to the CPU or another switch for DSA. If
the MTU is set too low, tagged frames will be discarded. Ensure the
worst case tagger overhead is included in setting the MTU for DSA and
CPU ports.
Fixes: 1baf0fac10 ("net: dsa: mv88e6xxx: Use chip-wide max frame size for MTU")
Reported by: 曹煜 <cao88yu@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b92ce2f54c ]
The MTU passed to the DSA driver is the payload size, typically 1500.
However, the switch uses the frame size when applying restrictions.
Adjust the MTU with the size of the Ethernet header and the frame
checksum. The VLAN header also needs to be included when the frame
size it per port, but not when it is global.
Fixes: 1baf0fac10 ("net: dsa: mv88e6xxx: Use chip-wide max frame size for MTU")
Reported by: 曹煜 <cao88yu@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe23036192 ]
The datasheets suggests the 6161 uses a per port setting for jumbo
frames. Testing has however shown this is not correct, it uses the old
style chip wide MTU control. Change the ops in the 6161 structure to
reflect this.
Fixes: 1baf0fac10 ("net: dsa: mv88e6xxx: Use chip-wide max frame size for MTU")
Reported by: 曹煜 <cao88yu@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c83ff01864 ]
Currently we blow up in trace_dma_fence_init, when calling into
get_driver_name or get_timeline_name, since both the engine and context
might be NULL(or contain some garbage address) in the case of newly
allocated slab objects via the request ctor. Note that we also use
SLAB_TYPESAFE_BY_RCU here, which allows requests to be immediately
freed, but delay freeing the underlying page by an RCU grace period.
With this scheme requests can be re-allocated, at the same time as they
are also being read by some lockless RCU lookup mechanism.
In the ctor case, which is only called for new slab objects(i.e allocate
new page and call the ctor for each object) it's safe to reset the
context/engine prior to calling into dma_fence_init, since we can be
certain that no one is doing an RCU lookup which might depend on peeking
at the engine/context, like in active_engine(), since the object can't
yet be externally visible.
In the recycled case(which might also be externally visible) the request
refcount always transitions from 0->1 after we set the context/engine
etc, which should ensure it's valid to dereference the engine for
example, when doing an RCU list-walk, so long as we can also increment
the refcount first. If the refcount is already zero, then the request is
considered complete/released. If it's non-zero, then the request might
be in the process of being re-allocated, or potentially still in flight,
however after successfully incrementing the refcount, it's possible to
carefully inspect the request state, to determine if the request is
still what we were looking for. Note that all externally visible
requests returned to the cache must have zero refcount.
One possible fix then is to move dma_fence_init out from the request
ctor. Originally this was how it was done, but it was moved in:
commit 855e39e65c
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Feb 3 09:41:48 2020 +0000
drm/i915: Initialise basic fence before acquiring seqno
where it looks like intel_timeline_get_seqno() relied on some of the
rq->fence state, but that is no longer the case since:
commit 12ca695d2c
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Tue Mar 23 16:49:50 2021 +0100
drm/i915: Do not share hwsp across contexts any more, v8.
intel_timeline_get_seqno() could also be cleaned up slightly by dropping
the request argument.
Moving dma_fence_init back out of the ctor, should ensure we have enough
of the request initialised in case of trace_dma_fence_init.
Functionally this should be the same, and is effectively what we were
already open coding before, except now we also assign the fence->lock
and fence->ops, but since these are invariant for recycled
requests(which might be externally visible), and will therefore already
hold the same value, it shouldn't matter.
An alternative fix, since we don't yet have a fully initialised request
when in the ctor, is just setting the context/engine as NULL, but this
does require adding some extra handling in get_driver_name etc.
v2(Daniel):
- Try to make the commit message less confusing
Fixes: 855e39e65c ("drm/i915: Initialise basic fence before acquiring seqno")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Michael Mason <michael.w.mason@intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921134202.3803151-1-matthew.auld@intel.com
(cherry picked from commit be988eaee1)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ab8a447bc ]
After commit 05b35e7eb9 ("smsc95xx: add phylib support"), link changes
are no longer propagated to usbnet. As a result, rx URB allocation won't
happen until there is a packet sent out first (this might never happen,
e.g. running just ssh server with a static IP). Fix by triggering usbnet
EVENT_LINK_CHANGE.
Fixes: 05b35e7eb9 ("smsc95xx: add phylib support")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 597aa16c78 ]
Multipath RTA_FLOW is embedded in nexthop. Dump it in fib_add_nexthop()
to get the length of rtnexthop correct.
Fixes: b0f6019363 ("ipv4: Refactor nexthop attributes in fib_dump_info")
Signed-off-by: Xiao Liang <shaw.leon@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 325fd36ae7 ]
The enetc phylink .mac_config handler intends to clear the IFMODE field
(bits 1:0) of the PM0_IF_MODE register, but incorrectly clears all the
other fields instead.
For normal operation, the bug was inconsequential, due to the fact that
we write the PM0_IF_MODE register in two stages, first in
phylink .mac_config (which incorrectly cleared out a bunch of stuff),
then we update the speed and duplex to the correct values in
phylink .mac_link_up.
Judging by the code (not tested), it looks like maybe loopback mode was
broken, since this is one of the settings in PM0_IF_MODE which is
incorrectly cleared.
Fixes: c76a97218d ("net: enetc: force the RGMII speed and duplex instead of operating in inband mode")
Reported-by: Pavel Machek (CIP) <pavel@denx.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 540effa7f2 ]
For both local and remote sensors all the supported ICs can report an
"undervoltage lockout" condition which means the conversion wasn't
properly performed due to insufficient power supply voltage and so the
measurement results can't be trusted.
Fixes: 9410700b88 ("hwmon: Add driver for Texas Instruments TMP421/422/423 sensor chips")
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Link: https://lore.kernel.org/r/20210924093011.26083-2-fercerpav@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea1300b9df ]
mptcp_token_get_sock() may return a mptcp socket that is in
a different net namespace than the socket that received the token value.
The mptcp syncookie code path had an explicit check for this,
this moves the test into mptcp_token_get_sock() function.
Eventually token.c should be converted to pernet storage, but
such change is not suitable for net tree.
Fixes: 2c5ebd001d ("mptcp: refactor token container")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7e745f8e9 ]
We should always check if skb_header_pointer's return is NULL before
using it, otherwise it may cause null-ptr-deref, as syzbot reported:
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
RIP: 0010:sctp_rcv_ootb net/sctp/input.c:705 [inline]
RIP: 0010:sctp_rcv+0x1d84/0x3220 net/sctp/input.c:196
Call Trace:
<IRQ>
sctp6_rcv+0x38/0x60 net/sctp/ipv6.c:1109
ip6_protocol_deliver_rcu+0x2e9/0x1ca0 net/ipv6/ip6_input.c:422
ip6_input_finish+0x62/0x170 net/ipv6/ip6_input.c:463
NF_HOOK include/linux/netfilter.h:307 [inline]
NF_HOOK include/linux/netfilter.h:301 [inline]
ip6_input+0x9c/0xd0 net/ipv6/ip6_input.c:472
dst_input include/net/dst.h:460 [inline]
ip6_rcv_finish net/ipv6/ip6_input.c:76 [inline]
NF_HOOK include/linux/netfilter.h:307 [inline]
NF_HOOK include/linux/netfilter.h:301 [inline]
ipv6_rcv+0x28c/0x3c0 net/ipv6/ip6_input.c:297
Fixes: 3acb50c18d ("sctp: delay as much as possible skb_linearize")
Reported-by: syzbot+581aff2ae6b860625116@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 313bbd1990 ]
Thomas explained in https://lore.kernel.org/r/87mtoeb4hb.ffs@tglx
that our handling of the hrtimer here is wrong: If the timer fires
late (e.g. due to vCPU scheduling, as reported by Dmitry/syzbot)
then it tries to actually rearm the timer at the next deadline,
which might be in the past already:
1 2 3 N N+1
| | | ... | |
^ intended to fire here (1)
^ next deadline here (2)
^ actually fired here
The next time it fires, it's later, but will still try to schedule
for the next deadline (now 3), etc. until it catches up with N,
but that might take a long time, causing stalls etc.
Now, all of this is simulation, so we just have to fix it, but
note that the behaviour is wrong even per spec, since there's no
value then in sending all those beacons unaligned - they should be
aligned to the TBTT (1, 2, 3, ... in the picture), and if we're a
bit (or a lot) late, then just resume at that point.
Therefore, change the code to use hrtimer_forward_now() which will
ensure that the next firing of the timer would be at N+1 (in the
picture), i.e. the next interval point after the current time.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Reported-by: syzbot+0e964fad69a9c462bc1e@syzkaller.appspotmail.com
Fixes: 01e59e467e ("mac80211_hwsim: hrtimer beacon")
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210915112936.544f383472eb.I3f9712009027aa09244b65399bf18bf482a8c4f1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe94bac626 ]
In ieee80211_amsdu_aggregate() set a pointer frag_tail point to the
end of skb_shinfo(head)->frag_list, and use it to bind other skb in
the end of this function. But when execute ieee80211_amsdu_aggregate()
->ieee80211_amsdu_realloc_pad()->pskb_expand_head(), the address of
skb_shinfo(head)->frag_list will be changed. However, the
ieee80211_amsdu_aggregate() not update frag_tail after call
pskb_expand_head(). That will cause the second skb can't bind to the
head skb appropriately.So we update the address of frag_tail to fix it.
Fixes: 6e0456b545 ("mac80211: add A-MSDU tx support")
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://lore.kernel.org/r/20210830073240.12736-1-pkshih@realtek.com
[reword comment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6fab7af6b ]
Fan speed minimum can be enforced from sysfs. For example, setting
current fan speed to 20 is used to enforce fan speed to be at 100%
speed, 19 - to be not below 90% speed, etcetera. This feature provides
ability to limit fan speed according to some system wise
considerations, like absence of some replaceable units or high system
ambient temperature.
Request for changing fan minimum speed is configuration request and can
be set only through 'sysfs' write procedure. In this situation value of
argument 'state' is above nominal fan speed maximum.
Return non-zero code in this case to avoid
thermal_cooling_device_stats_update() call, because in this case
statistics update violates thermal statistics table range.
The issues is observed in case kernel is configured with option
CONFIG_THERMAL_STATISTICS.
Here is the trace from KASAN:
[ 159.506659] BUG: KASAN: slab-out-of-bounds in thermal_cooling_device_stats_update+0x7d/0xb0
[ 159.516016] Read of size 4 at addr ffff888116163840 by task hw-management.s/7444
[ 159.545625] Call Trace:
[ 159.548366] dump_stack+0x92/0xc1
[ 159.552084] ? thermal_cooling_device_stats_update+0x7d/0xb0
[ 159.635869] thermal_zone_device_update+0x345/0x780
[ 159.688711] thermal_zone_device_set_mode+0x7d/0xc0
[ 159.694174] mlxsw_thermal_modules_init+0x48f/0x590 [mlxsw_core]
[ 159.700972] ? mlxsw_thermal_set_cur_state+0x5a0/0x5a0 [mlxsw_core]
[ 159.731827] mlxsw_thermal_init+0x763/0x880 [mlxsw_core]
[ 160.070233] RIP: 0033:0x7fd995909970
[ 160.074239] Code: 73 01 c3 48 8b 0d 28 d5 2b 00 f7 d8 64 89 01 48 83 c8 ff c3 66 0f 1f 44 00 00 83 3d 99 2d 2c 00 00 75 10 b8 01 00 00 00 0f 05 <48> 3d 01 f0 ff ..
[ 160.095242] RSP: 002b:00007fff54f5d938 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
[ 160.103722] RAX: ffffffffffffffda RBX: 0000000000000013 RCX: 00007fd995909970
[ 160.111710] RDX: 0000000000000013 RSI: 0000000001906008 RDI: 0000000000000001
[ 160.119699] RBP: 0000000001906008 R08: 00007fd995bc9760 R09: 00007fd996210700
[ 160.127687] R10: 0000000000000073 R11: 0000000000000246 R12: 0000000000000013
[ 160.135673] R13: 0000000000000001 R14: 00007fd995bc8600 R15: 0000000000000013
[ 160.143671]
[ 160.145338] Allocated by task 2924:
[ 160.149242] kasan_save_stack+0x19/0x40
[ 160.153541] __kasan_kmalloc+0x7f/0xa0
[ 160.157743] __kmalloc+0x1a2/0x2b0
[ 160.161552] thermal_cooling_device_setup_sysfs+0xf9/0x1a0
[ 160.167687] __thermal_cooling_device_register+0x1b5/0x500
[ 160.173833] devm_thermal_of_cooling_device_register+0x60/0xa0
[ 160.180356] mlxreg_fan_probe+0x474/0x5e0 [mlxreg_fan]
[ 160.248140]
[ 160.249807] The buggy address belongs to the object at ffff888116163400
[ 160.249807] which belongs to the cache kmalloc-1k of size 1024
[ 160.263814] The buggy address is located 64 bytes to the right of
[ 160.263814] 1024-byte region [ffff888116163400, ffff888116163800)
[ 160.277536] The buggy address belongs to the page:
[ 160.282898] page:0000000012275840 refcount:1 mapcount:0 mapping:0000000000000000 index:0xffff888116167000 pfn:0x116160
[ 160.294872] head:0000000012275840 order:3 compound_mapcount:0 compound_pincount:0
[ 160.303251] flags: 0x200000000010200(slab|head|node=0|zone=2)
[ 160.309694] raw: 0200000000010200 ffffea00046f7208 ffffea0004928208 ffff88810004dbc0
[ 160.318367] raw: ffff888116167000 00000000000a0006 00000001ffffffff 0000000000000000
[ 160.327033] page dumped because: kasan: bad access detected
[ 160.333270]
[ 160.334937] Memory state around the buggy address:
[ 160.356469] >ffff888116163800: fc ..
Fixes: 65afb4c8e7 ("hwmon: (mlxreg-fan) Add support for Mellanox FAN driver")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20210916183151.869427-1-vadimp@nvidia.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca465e1f1f ]
If cma_listen_on_all() fails it leaves the per-device ID still on the
listen_list but the state is not set to RDMA_CM_ADDR_BOUND.
When the cmid is eventually destroyed cma_cancel_listens() is not called
due to the wrong state, however the per-device IDs are still holding the
refcount preventing the ID from being destroyed, thus deadlocking:
task:rping state:D stack: 0 pid:19605 ppid: 47036 flags:0x00000084
Call Trace:
__schedule+0x29a/0x780
? free_unref_page_commit+0x9b/0x110
schedule+0x3c/0xa0
schedule_timeout+0x215/0x2b0
? __flush_work+0x19e/0x1e0
wait_for_completion+0x8d/0xf0
_destroy_id+0x144/0x210 [rdma_cm]
ucma_close_id+0x2b/0x40 [rdma_ucm]
__destroy_id+0x93/0x2c0 [rdma_ucm]
? __xa_erase+0x4a/0xa0
ucma_destroy_id+0x9a/0x120 [rdma_ucm]
ucma_write+0xb8/0x130 [rdma_ucm]
vfs_write+0xb4/0x250
ksys_write+0xb5/0xd0
? syscall_trace_enter.isra.19+0x123/0x190
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Ensure that cma_listen_on_all() atomically unwinds its action under the
lock during error.
Fixes: c80a0c52d8 ("RDMA/cma: Add missing error handling of listen_id")
Link: https://lore.kernel.org/r/20210913093344.17230-1-thomas.liu@ucloud.cn
Signed-off-by: Tao Liu <thomas.liu@ucloud.cn>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2cc74e1ee3 ]
ROCE uses IGMP for Multicast instead of the native Infiniband system where
joins are required in order to post messages on the Multicast group. On
Ethernet one can send Multicast messages to arbitrary addresses without
the need to subscribe to a group.
So ROCE correctly does not send IGMP joins during rdma_join_multicast().
F.e. in cma_iboe_join_multicast() we see:
if (addr->sa_family == AF_INET) {
if (gid_type == IB_GID_TYPE_ROCE_UDP_ENCAP) {
ib.rec.hop_limit = IPV6_DEFAULT_HOPLIMIT;
if (!send_only) {
err = cma_igmp_send(ndev, &ib.rec.mgid,
true);
}
}
} else {
So the IGMP join is suppressed as it is unnecessary.
However no such check is done in destroy_mc(). And therefore leaving a
sendonly multicast group will send an IGMP leave.
This means that the following scenario can lead to a multicast receiver
unexpectedly being unsubscribed from a MC group:
1. Sender thread does a sendonly join on MC group X. No IGMP join
is sent.
2. Receiver thread does a regular join on the same MC Group x.
IGMP join is sent and the receiver begins to get messages.
3. Sender thread terminates and destroys MC group X.
IGMP leave is sent and the receiver no longer receives data.
This patch adds the same logic for sendonly joins to destroy_mc() that is
also used in cma_iboe_join_multicast().
Fixes: ab15c95a17 ("IB/core: Support for CMA multicast join flags")
Link: https://lore.kernel.org/r/alpine.DEB.2.22.394.2109081340540.668072@gentwo.de
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 356ed64991 ]
Currently if a function ptr in struct_ops has a return value, its
caller will get a random return value from it, because the return
value of related BPF_PROG_TYPE_STRUCT_OPS prog is just dropped.
So adding a new flag BPF_TRAMP_F_RET_FENTRY_RET to tell bpf trampoline
to save and return the return value of struct_ops prog if ret_size of
the function ptr is greater than 0. Also restricting the flag to be
used alone.
Fixes: 85d33df357 ("bpf: Introduce BPF_MAP_TYPE_STRUCT_OPS")
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20210914023351.3664499-1-houtao1@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69e73dbfda ]
ip_vs_conn_tab_bits may be provided by the user through the
conn_tab_bits module parameter. If this value is greater than 31, or
less than 0, the shift operator used to derive tab_size causes undefined
behaviour.
Fix this checking ip_vs_conn_tab_bits value to be in the range specified
in ipvs Kconfig. If not, simply use default value.
Fixes: 6f7edb4881 ("IPVS: Allow boot time change of hash size")
Reported-by: Yi Chen <yiche@redhat.com>
Signed-off-by: Andrea Claudi <aclaudi@redhat.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit bc0bdc5afa upstream.
If the state is not idle then rdma_bind_addr() will immediately fail and
no change to global state should happen.
For instance if the state is already RDMA_CM_LISTEN then this will corrupt
the src_addr and would cause the test in cma_cancel_operation():
if (cma_any_addr(cma_src_addr(id_priv)) && !id_priv->cma_dev)
To view a mangled src_addr, eg with a IPv6 loopback address but an IPv4
family, failing the test.
This would manifest as this trace from syzkaller:
BUG: KASAN: use-after-free in __list_add_valid+0x93/0xa0 lib/list_debug.c:26
Read of size 8 at addr ffff8881546491e0 by task syz-executor.1/32204
CPU: 1 PID: 32204 Comm: syz-executor.1 Not tainted 5.12.0-rc8-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:79 [inline]
dump_stack+0x141/0x1d7 lib/dump_stack.c:120
print_address_description.constprop.0.cold+0x5b/0x2f8 mm/kasan/report.c:232
__kasan_report mm/kasan/report.c:399 [inline]
kasan_report.cold+0x7c/0xd8 mm/kasan/report.c:416
__list_add_valid+0x93/0xa0 lib/list_debug.c:26
__list_add include/linux/list.h:67 [inline]
list_add_tail include/linux/list.h:100 [inline]
cma_listen_on_all drivers/infiniband/core/cma.c:2557 [inline]
rdma_listen+0x787/0xe00 drivers/infiniband/core/cma.c:3751
ucma_listen+0x16a/0x210 drivers/infiniband/core/ucma.c:1102
ucma_write+0x259/0x350 drivers/infiniband/core/ucma.c:1732
vfs_write+0x28e/0xa30 fs/read_write.c:603
ksys_write+0x1ee/0x250 fs/read_write.c:658
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xae
Which is indicating that an rdma_id_private was destroyed without doing
cma_cancel_listens().
Instead of trying to re-use the src_addr memory to indirectly create an
any address build one explicitly on the stack and bind to that as any
other normal flow would do.
Link: https://lore.kernel.org/r/0-v1-9fbb33f5e201+2a-cma_listen_jgg@nvidia.com
Cc: stable@vger.kernel.org
Fixes: 732d41c545 ("RDMA/cma: Make the locking for automatic state transition more clear")
Reported-by: syzbot+6bb0528b13611047209c@syzkaller.appspotmail.com
Tested-by: Hao Sun <sunhao.th@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8646e53633 upstream.
Invoke rseq's NOTIFY_RESUME handler when processing the flag prior to
transferring to a KVM guest, which is roughly equivalent to an exit to
userspace and processes many of the same pending actions. While the task
cannot be in an rseq critical section as the KVM path is reachable only
by via ioctl(KVM_RUN), the side effects that apply to rseq outside of a
critical section still apply, e.g. the current CPU needs to be updated if
the task is migrated.
Clearing TIF_NOTIFY_RESUME without informing rseq can lead to segfaults
and other badness in userspace VMMs that use rseq in combination with KVM,
e.g. due to the CPU ID being stale after task migration.
Fixes: 72c3c0fe54 ("x86/kvm: Use generic xfer to guest work function")
Reported-by: Peter Foley <pefoley@google.com>
Bisected-by: Doug Evans <dje@google.com>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210901203030.1292304-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[sean: Resolve benign conflict due to unrelated access_ok() check in 5.10]
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d68bad6d8 upstream.
Windows Server 2022 with Hyper-V role enabled failed to boot on KVM when
enlightened VMCS is advertised. Debugging revealed there are two exposed
secondary controls it is not happy with: SECONDARY_EXEC_ENABLE_VMFUNC and
SECONDARY_EXEC_SHADOW_VMCS. These controls are known to be unsupported,
as there are no corresponding fields in eVMCSv1 (see the comment above
EVMCS1_UNSUPPORTED_2NDEXEC definition).
Previously, commit 31de3d2500 ("x86/kvm/hyper-v: move VMX controls
sanitization out of nested_enable_evmcs()") introduced the required
filtering mechanism for VMX MSRs but for some reason put only known
to be problematic (and not full EVMCS1_UNSUPPORTED_* lists) controls
there.
Note, Windows Server 2022 seems to have gained some sanity check for VMX
MSRs: it doesn't even try to launch a guest when there's something it
doesn't like, nested_evmcs_check_controls() mechanism can't catch the
problem.
Let's be bold this time and instead of playing whack-a-mole just filter out
all unsupported controls from VMX MSRs.
Fixes: 31de3d2500 ("x86/kvm/hyper-v: move VMX controls sanitization out of nested_enable_evmcs()")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20210907163530.110066-1-vkuznets@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f9b68f57c upstream.
KASAN reports the following issue:
BUG: KASAN: stack-out-of-bounds in kvm_make_vcpus_request_mask+0x174/0x440 [kvm]
Read of size 8 at addr ffffc9001364f638 by task qemu-kvm/4798
CPU: 0 PID: 4798 Comm: qemu-kvm Tainted: G X --------- ---
Hardware name: AMD Corporation DAYTONA_X/DAYTONA_X, BIOS RYM0081C 07/13/2020
Call Trace:
dump_stack+0xa5/0xe6
print_address_description.constprop.0+0x18/0x130
? kvm_make_vcpus_request_mask+0x174/0x440 [kvm]
__kasan_report.cold+0x7f/0x114
? kvm_make_vcpus_request_mask+0x174/0x440 [kvm]
kasan_report+0x38/0x50
kasan_check_range+0xf5/0x1d0
kvm_make_vcpus_request_mask+0x174/0x440 [kvm]
kvm_make_scan_ioapic_request_mask+0x84/0xc0 [kvm]
? kvm_arch_exit+0x110/0x110 [kvm]
? sched_clock+0x5/0x10
ioapic_write_indirect+0x59f/0x9e0 [kvm]
? static_obj+0xc0/0xc0
? __lock_acquired+0x1d2/0x8c0
? kvm_ioapic_eoi_inject_work+0x120/0x120 [kvm]
The problem appears to be that 'vcpu_bitmap' is allocated as a single long
on stack and it should really be KVM_MAX_VCPUS long. We also seem to clear
the lower 16 bits of it with bitmap_zero() for no particular reason (my
guess would be that 'bitmap' and 'vcpu_bitmap' variables in
kvm_bitmap_or_dest_vcpus() caused the confusion: while the later is indeed
16-bit long, the later should accommodate all possible vCPUs).
Fixes: 7ee30bc132 ("KVM: x86: deliver KVM IOAPIC scan request to target vCPUs")
Fixes: 9a2ae9f6b6 ("KVM: x86: Zero the IOAPIC scan request dest vCPUs bitmap")
Reported-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210827092516.1027264-7-vkuznets@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 943c15ac1b upstream.
If driver read val value sufficient for
(val & 0x08) && (!(val & 0x80)) && ((val & 0x7) == ((val >> 4) & 0x7))
from device then Null pointer dereference occurs.
(It is possible if tmp = 0b0xyz1xyz, where same literals mean same numbers)
Also lm75[] does not serve a purpose anymore after switching to
devm_i2c_new_dummy_device() in w83791d_detect_subclients().
The patch fixes possible NULL pointer dereference by removing lm75[].
Found by Linux Driver Verification project (linuxtesting.org).
Cc: stable@vger.kernel.org
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Link: https://lore.kernel.org/r/20210921155153.28098-1-lutovinova@ispras.ru
[groeck: Dropped unnecessary continuation lines, fixed multi-line alignment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f36b88173 upstream.
If driver read val value sufficient for
(val & 0x08) && (!(val & 0x80)) && ((val & 0x7) == ((val >> 4) & 0x7))
from device then Null pointer dereference occurs.
(It is possible if tmp = 0b0xyz1xyz, where same literals mean same numbers)
Also lm75[] does not serve a purpose anymore after switching to
devm_i2c_new_dummy_device() in w83791d_detect_subclients().
The patch fixes possible NULL pointer dereference by removing lm75[].
Found by Linux Driver Verification project (linuxtesting.org).
Cc: stable@vger.kernel.org
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Link: https://lore.kernel.org/r/20210921155153.28098-2-lutovinova@ispras.ru
[groeck: Dropped unnecessary continuation lines, fixed multipline alignment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd4d747ef0 upstream.
If driver read tmp value sufficient for
(tmp & 0x08) && (!(tmp & 0x80)) && ((tmp & 0x7) == ((tmp >> 4) & 0x7))
from device then Null pointer dereference occurs.
(It is possible if tmp = 0b0xyz1xyz, where same literals mean same numbers)
Also lm75[] does not serve a purpose anymore after switching to
devm_i2c_new_dummy_device() in w83791d_detect_subclients().
The patch fixes possible NULL pointer dereference by removing lm75[].
Found by Linux Driver Verification project (linuxtesting.org).
Cc: stable@vger.kernel.org
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Link: https://lore.kernel.org/r/20210921155153.28098-3-lutovinova@ispras.ru
[groeck: Dropped unnecessary continuation lines, fixed multi-line alignments]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2938b2978a upstream.
Function i2c_smbus_read_byte_data() can return a negative error number
instead of the data read if I2C transaction failed for whatever reason.
Lack of error checking can lead to serious issues on production
hardware, e.g. errors treated as temperatures produce spurious critical
temperature-crossed-threshold errors in BMC logs for OCP server
hardware. The patch was tested with Mellanox OCP Mezzanine card
emulating TMP421 protocol for temperature sensing which sometimes leads
to I2C protocol error during early boot up stage.
Fixes: 9410700b88 ("hwmon: Add driver for Texas Instruments TMP421/422/423 sensor chips")
Cc: stable@vger.kernel.org
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Link: https://lore.kernel.org/r/20210924093011.26083-1-fercerpav@gmail.com
[groeck: dropped unnecessary line breaks]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 80f6e3080b upstream.
If the file size is almost S64_MAX, the calculated number of Merkle tree
levels exceeds FS_VERITY_MAX_LEVELS, causing FS_IOC_ENABLE_VERITY to
fail. This is unintentional, since as the comment above the definition
of FS_VERITY_MAX_LEVELS states, it is enough for over U64_MAX bytes of
data using SHA-256 and 4K blocks. (Specifically, 4096*128**8 >= 2**64.)
The bug is actually that when the number of blocks in the first level is
calculated from i_size, there is a signed integer overflow due to i_size
being signed. Fix this by treating i_size as unsigned.
This was found by the new test "generic: test fs-verity EFBIG scenarios"
(https://lkml.kernel.org/r/b1d116cd4d0ea74b9cd86f349c672021e005a75c.1631558495.git.boris@bur.io).
This didn't affect ext4 or f2fs since those have a smaller maximum file
size, but it did affect btrfs which allows files up to S64_MAX bytes.
Reported-by: Boris Burkov <boris@bur.io>
Fixes: 3fda4c617e ("fs-verity: implement FS_IOC_ENABLE_VERITY ioctl")
Fixes: fd2d1acfca ("fs-verity: add the hook for file ->open()")
Cc: <stable@vger.kernel.org> # v5.4+
Reviewed-by: Boris Burkov <boris@bur.io>
Link: https://lore.kernel.org/r/20210916203424.113376-1-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f060db9937 upstream.
When ACPI NFIT table is failing to populate correct numa information
on arm64, dax_kmem will get NUMA_NO_NODE from the NFIT driver.
Without this patch, pmem can't be probed as RAM devices on arm64 guest:
$ndctl create-namespace -fe namespace0.0 --mode=devdax --map=dev -s 1g -a 128M
kmem dax0.0: rejecting DAX region [mem 0x240400000-0x2bfffffff] with invalid node: -1
kmem: probe of dax0.0 failed with error -22
Suggested-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jia He <justin.he@arm.com>
Cc: <stable@vger.kernel.org>
Fixes: c221c0b030 ("device-dax: "Hotplug" persistent memory for use like normal RAM")
Link: https://lore.kernel.org/r/20210922152919.6940-1-justin.he@arm.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad7cc2d41b upstream.
This patch initializes and enables speaker output on the Lenovo Legion 7i
15IMHG05, Yoga 7i 14ITL5/15ITL5, and 13s Gen2 series of laptops using the
HDA verb sequence specific to each model.
Speaker automute is suppressed for the Lenovo Legion 7i 15IMHG05 to avoid
breaking speaker output on resume and when devices are unplugged from its
headphone jack.
Thanks to: Andreas Holzer, Vincent Morel, sycxyc, Max Christian Pohle and
all others that helped.
[ minor coding style fixes by tiwai ]
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=208555
Signed-off-by: Cameron Berkenpas <cam@neo-zeon.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210913212627.339362-1-cam@neo-zeon.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3b0c406124 ]
This issue happens when a userspace program does an ioctl
FBIOPUT_VSCREENINFO passing the fb_var_screeninfo struct
containing only the fields xres, yres, and bits_per_pixel
with values.
If this struct is the same as the previous ioctl, the
vc_resize() detects it and doesn't call the resize_screen(),
leaving the fb_var_screeninfo incomplete. And this leads to
the updatescrollmode() calculates a wrong value to
fbcon_display->vrows, which makes the real_y() return a
wrong value of y, and that value, eventually, causes
the imageblit to access an out-of-bound address value.
To solve this issue I made the resize_screen() be called
even if the screen does not need any resizing, so it will
"fix and fill" the fb_var_screeninfo independently.
Cc: stable <stable@vger.kernel.org> # after 5.15-rc2 is out, give it time to bake
Reported-and-tested-by: syzbot+858dc7a2f7ef07c2c219@syzkaller.appspotmail.com
Signed-off-by: Igor Matheus Andrade Torrente <igormtorrente@gmail.com>
Link: https://lore.kernel.org/r/20210628134509.15895-1-igormtorrente@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Adds an overlay to configure the TinyDRM driver for ST7735R
based 160x128 and 128x128 (untested) displays such as the
Adafruit 1.8" display.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
This commit updates the imx519 driver to adverise support for embedded
data streams.
The imx519 sensor subdevice overloads the media pad to differentiate
between image stream (pad 0) and embedded data stream (pad 1) when
performing the v4l2_subdev_pad_ops functions.
Signed-off-by: Lee Jackson <info@arducam.com>
Adds a driver for the 16MPix IMX519 CSI2 sensor.
Whilst the sensor supports 2 or 4 CSI2 data lanes, this driver
currently only supports 2 lanes.
The following Bayer modes are currently available:
4656x3496 10-bit @ 10fps
3840x2160 10-bit (cropped) @ 21fps
2328x1748 10-bit (binned) @ 30fps
1920x1080 10-bit (cropped/binned) @ 60fps
1280x720 10-bit (cropped/binned) @ 120fps
Signed-off-by: Lee Jackson <info@arducam.com>
commit d5f6545934 upstream.
In commit b7213ffa0e ("qnx4: avoid stringop-overread errors") I tried
to teach gcc about how the directory entry structure can be two
different things depending on a status flag. It made the code clearer,
and it seemed to make gcc happy.
However, Arnd points to a gcc bug, where despite using two different
members of a union, gcc then gets confused, and uses the size of one of
the members to decide if a string overrun happens. And not necessarily
the rigth one.
End result: with some configurations, gcc-11 will still complain about
the source buffer size being overread:
fs/qnx4/dir.c: In function 'qnx4_readdir':
fs/qnx4/dir.c:76:32: error: 'strnlen' specified bound [16, 48] exceeds source size 1 [-Werror=stringop-overread]
76 | size = strnlen(name, size);
| ^~~~~~~~~~~~~~~~~~~
fs/qnx4/dir.c:26:22: note: source object declared here
26 | char de_name;
| ^~~~~~~
because gcc will get confused about which union member entry is actually
getting accessed, even when the source code is very clear about it. Gcc
internally will have combined two "redundant" pointers (pointing to
different union elements that are at the same offset), and takes the
size checking from one or the other - not necessarily the right one.
This is clearly a gcc bug, but we can work around it fairly easily. The
biggest thing here is the big honking comment about why we do what we
do.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=99578#c6
Reported-and-tested-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c32dfec6c1 upstream.
Some CP2102 do not support event-insertion mode but return no error when
attempting to enable it.
This means that any event escape characters in the input stream will not
be escaped by the device and consequently regular data may be
interpreted as escape sequences and be removed from the stream by the
driver.
The reporter's device has batch number DCL00X etched into it and as
discovered by the SHA2017 Badge team, counterfeit devices with that
marking can be detected by sending malformed vendor requests. [1][2]
Tests confirm that the possibly counterfeit CP2102 returns a single byte
in response to a malformed two-byte part-number request, while an
original CP2102 returns two bytes. Assume that every CP2102 that behaves
this way also does not support event-insertion mode (e.g. cannot report
parity errors).
[1] https://mobile.twitter.com/sha2017badge/status/1167902087289532418
[2] https://hackaday.com/2017/08/14/hands-on-with-the-shacamp-2017-badge/#comment-3903376
Reported-by: Malte Di Donato <malte@neo-soft.org>
Tested-by: Malte Di Donato <malte@neo-soft.org>
Fixes: a7207e9835 ("USB: serial: cp210x: add support for line-status events")
Cc: stable@vger.kernel.org # 5.9
Link: https://lore.kernel.org/r/20210922113100.20888-1-johan@kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b4bd25667 upstream.
After upgrading to Linux 5.13.3 I noticed my laptop would shutdown due
to overheat (when it should not). It turned out this was due to commit
fe6a6de669 ("thermal/drivers/int340x/processor_thermal: Fix tcc setting").
What happens is this drivers uses a global variable to keep track of the
tcc offset (tcc_offset_save) and uses it on resume. The issue is this
variable is initialized to 0, but is only set in
tcc_offset_degree_celsius_store, i.e. when the tcc offset is explicitly
set by userspace. If that does not happen, the resume path will set the
offset to 0 (in my case the h/w default being 3, the offset would become
too low after a suspend/resume cycle).
The issue did not arise before commit fe6a6de669, as the function
setting the offset would return if the offset was 0. This is no longer
the case (rightfully).
Fix this by not applying the offset if it wasn't saved before, reverting
back to the old logic. A better approach will come later, but this will
be easier to apply to stable kernels.
The logic to restore the offset after a resume was there long before
commit fe6a6de669, but as a value of 0 was considered invalid I'm
referencing the commit that made the issue possible in the Fixes tag
instead.
Fixes: fe6a6de669 ("thermal/drivers/int340x/processor_thermal: Fix tcc setting")
Cc: stable@vger.kernel.org
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: Srinivas Pandruvada <srinivas.pI andruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20210909085613.5577-2-atenart@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit efafec27c5 ]
Without CONFIG_PM enabled, the SET_RUNTIME_PM_OPS() macro ends up being
empty, and the only use of tegra_slink_runtime_{resume,suspend} goes
away, resulting in
drivers/spi/spi-tegra20-slink.c:1200:12: error: ‘tegra_slink_runtime_resume’ defined but not used [-Werror=unused-function]
1200 | static int tegra_slink_runtime_resume(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/spi/spi-tegra20-slink.c:1188:12: error: ‘tegra_slink_runtime_suspend’ defined but not used [-Werror=unused-function]
1188 | static int tegra_slink_runtime_suspend(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~
mark the functions __maybe_unused to make the build happy.
This hits the alpha allmodconfig build (and others).
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c0d2a46c0 ]
tx timeout and slot time are currently specified in units of HZ. On
Alpha, HZ is defined as 1024. When building alpha:allmodconfig, this
results in the following error message.
drivers/net/hamradio/6pack.c: In function 'sixpack_open':
drivers/net/hamradio/6pack.c:71:41: error:
unsigned conversion from 'int' to 'unsigned char'
changes value from '256' to '0'
In the 6PACK protocol, tx timeout is specified in units of 10 ms and
transmitted over the wire:
https://www.linux-ax25.org/wiki/6PACK
Defining a value dependent on HZ doesn't really make sense, and
presumably comes from the (very historical) situation where HZ was
originally 100.
Note that the SIXP_SLOTTIME use explicitly is about 10ms granularity:
mod_timer(&sp->tx_t, jiffies + ((when + 1) * HZ) / 100);
and the SIXP_TXDELAY walue is sent as a byte over the wire.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35a3f4ef0a ]
Some drivers pass a pointer to volatile data to virt_to_bus() and
virt_to_phys(), and that works fine. One exception is alpha. This
results in a number of compile errors such as
drivers/net/wan/lmc/lmc_main.c: In function 'lmc_softreset':
drivers/net/wan/lmc/lmc_main.c:1782:50: error:
passing argument 1 of 'virt_to_bus' discards 'volatile'
qualifier from pointer target type
drivers/atm/ambassador.c: In function 'do_loader_command':
drivers/atm/ambassador.c:1747:58: error:
passing argument 1 of 'virt_to_bus' discards 'volatile'
qualifier from pointer target type
Declare the parameter of virt_to_phys and virt_to_bus as pointer to
volatile to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7213ffa0e ]
The qnx4 directory entries are 64-byte blocks that have different
contents depending on the a status byte that is in the last byte of the
block.
In particular, a directory entry can be either a "link info" entry with
a 48-byte name and pointers to the real inode information, or an "inode
entry" with a smaller 16-byte name and the full inode information.
But the code was written to always just treat the directory name as if
it was part of that "inode entry", and just extend the name to the
longer case if the status byte said it was a link entry.
That work just fine and gives the right results, but now that gcc is
tracking data structure accesses much more, the code can trigger a
compiler error about using up to 48 bytes (the long name) in a structure
that only has that shorter name in it:
fs/qnx4/dir.c: In function ‘qnx4_readdir’:
fs/qnx4/dir.c:51:32: error: ‘strnlen’ specified bound 48 exceeds source size 16 [-Werror=stringop-overread]
51 | size = strnlen(de->di_fname, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from fs/qnx4/qnx4.h:3,
from fs/qnx4/dir.c:16:
include/uapi/linux/qnx4_fs.h:45:25: note: source object declared here
45 | char di_fname[QNX4_SHORT_NAME_MAX];
| ^~~~~~~~
which is because the source code doesn't really make this whole "one of
two different types" explicit.
Fix this by introducing a very explicit union of the two types, and
basically explaining to the compiler what is really going on.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc7c028dcd ]
The sparc mdesc code does pointer games with 'struct mdesc_hdr', but
didn't describe to the compiler how that header is then followed by the
data that the header describes.
As a result, gcc is now unhappy since it does stricter pointer range
tracking, and doesn't understand about how these things work. This
results in various errors like:
arch/sparc/kernel/mdesc.c: In function ‘mdesc_node_by_name’:
arch/sparc/kernel/mdesc.c:647:22: error: ‘strcmp’ reading 1 or more bytes from a region of size 0 [-Werror=stringop-overread]
647 | if (!strcmp(names + ep[ret].name_offset, name))
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
which are easily avoided by just describing 'struct mdesc_hdr' better,
and making the node_block() helper function look into that unsized
data[] that follows the header.
This makes the sparc64 build happy again at least for my cross-compiler
version (gcc version 11.2.1).
Link: https://lore.kernel.org/lkml/CAHk-=wi4NW3NC0xWykkw=6LnjQD6D_rtRtxY9g8gQAJXtQMi8A@mail.gmail.com/
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dff2d13114 ]
gcc 11.x reports the following compiler warning/error.
drivers/net/ethernet/i825xx/82596.c: In function 'i82596_probe':
arch/m68k/include/asm/string.h:72:25: error:
'__builtin_memcpy' reading 6 bytes from a region of size 0 [-Werror=stringop-overread]
Use absolute_pointer() to work around the problem.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6b5f1a569 ]
absolute_pointer() disassociates a pointer from its originating symbol
type and context. Use it to prevent compiler warnings/errors such as
drivers/net/ethernet/i825xx/82596.c: In function 'i82596_probe':
arch/m68k/include/asm/string.h:72:25: error:
'__builtin_memcpy' reading 6 bytes from a region of size 0 [-Werror=stringop-overread]
Such warnings may be reported by gcc 11.x for string and memory
operations on fixed addresses.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3df49967f6 ]
When the integrity profile is unregistered there can still be integrity
reads queued up which could see a NULL verify_fn as shown by the race
window below:
CPU0 CPU1
process_one_work nvme_validate_ns
bio_integrity_verify_fn nvme_update_ns_info
nvme_update_disk_info
blk_integrity_unregister
---set queue->integrity as 0
bio_integrity_process
--access bi->profile->verify_fn(bi is a pointer of queue->integity)
Before calling blk_integrity_unregister in nvme_update_disk_info, we must
make sure that there is no work item in the kintegrityd_wq. Just call
blk_flush_integrity to flush the work queue so the bug can be resolved.
Signed-off-by: Lihong Kou <koulihong@huawei.com>
[hch: split up and shortened the changelog]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Link: https://lore.kernel.org/r/20210914070657.87677-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7bbee36d71 ]
In amdgpu_dm_atomic_check, dc_validate_global_state is called. On
failure this logs a warning to the kernel journal. However warnings
shouldn't be used for atomic test-only commit failures: user-space
might be perfoming a lot of atomic test-only commits to find the
best hardware configuration.
Downgrade the log to a regular DRM atomic message. While at it, use
the new device-aware logging infrastructure.
This fixes error messages in the kernel when running gamescope [1].
[1]: https://github.com/Plagman/gamescope/issues/245
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Simon Ser <contact@emersion.fr>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59583f7476 ]
Commit 53b7670e57 ("sparc: factor the dma coherent mapping into
helper") lost the page align for the calls to dma_make_coherent and
srmmu_unmapiorange. The latter cannot handle a non page aligned len
argument.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9817d763db ]
We should always destroy cm_id before destroy qp to avoid to get cma
event after qp was destroyed, which may lead to use after free.
In RDMA connection establishment error flow, don't destroy qp in cm
event handler.Just report cm_error to upper level, qp will be destroy
in nvme_rdma_alloc_queue() after destroy cm id.
Signed-off-by: Ruozhu Li <liruozhu@huawei.com>
Reviewed-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79f528afa9 ]
nvme_update_ana_state() has a deficiency that results in a failure to
properly update the ana state for a namespace in the following case:
NSIDs in ctrl->namespaces: 1, 3, 4
NSIDs in desc->nsids: 1, 2, 3, 4
Loop iteration 0:
ns index = 0, n = 0, ns->head->ns_id = 1, nsid = 1, MATCH.
Loop iteration 1:
ns index = 1, n = 1, ns->head->ns_id = 3, nsid = 2, NO MATCH.
Loop iteration 2:
ns index = 2, n = 2, ns->head->ns_id = 4, nsid = 4, MATCH.
Where the update to the ANA state of NSID 3 is missed. To fix this
increment n and retry the update with the same ns when ns->head->ns_id is
higher than nsid,
Signed-off-by: Anton Eidelman <anton@lightbitslabs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8480ed9c2b ]
Today the Xen ballooning is done via delayed work in a workqueue. This
might result in workqueue hangups being reported in case of large
amounts of memory are being ballooned in one go (here 16GB):
BUG: workqueue lockup - pool cpus=6 node=0 flags=0x0 nice=0 stuck for 64s!
Showing busy workqueues and worker pools:
workqueue events: flags=0x0
pwq 12: cpus=6 node=0 flags=0x0 nice=0 active=2/256 refcnt=3
in-flight: 229:balloon_process
pending: cache_reap
workqueue events_freezable_power_: flags=0x84
pwq 12: cpus=6 node=0 flags=0x0 nice=0 active=1/256 refcnt=2
pending: disk_events_workfn
workqueue mm_percpu_wq: flags=0x8
pwq 12: cpus=6 node=0 flags=0x0 nice=0 active=1/256 refcnt=2
pending: vmstat_update
pool 12: cpus=6 node=0 flags=0x0 nice=0 hung=64s workers=3 idle: 2222 43
This can easily be avoided by using a dedicated kernel thread for doing
the ballooning work.
Reported-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20210827123206.15429-1-jgross@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9a7e9df73 ]
If HWP has been already been enabled by BIOS, it may be
necessary to override some kernel command line parameters.
Once it has been enabled it requires a reset to be disabled.
Suggested-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1a89856fb ]
m68k builds fail widely with errors such as
arch/m68k/include/asm/raw_io.h:20:19: error:
cast to pointer from integer of different size
arch/m68k/include/asm/raw_io.h:30:32: error:
cast to pointer from integer of different size [-Werror=int-to-p
On m68k, io functions are defined as macros. The problem is seen if the
macro parameter variable size differs from the size of a pointer. Cast
the parameter of all io macros to unsigned long before casting it to
a pointer to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210907060729.2391992-1-linux@roeck-us.net
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 67f3b2f822 ]
blk-mq can't run allocating driver tag and updating ->rqs[tag]
atomically, meantime blk-mq doesn't clear ->rqs[tag] after the driver
tag is released.
So there is chance to iterating over one stale request just after the
tag is allocated and before updating ->rqs[tag].
scsi_host_busy_iter() calls scsi_host_check_in_flight() to count scsi
in-flight requests after scsi host is blocked, so no new scsi command can
be marked as SCMD_STATE_INFLIGHT. However, driver tag allocation still can
be run by blk-mq core. One request is marked as SCMD_STATE_INFLIGHT,
but this request may have been kept in another slot of ->rqs[], meantime
the slot can be allocated out but ->rqs[] isn't updated yet. Then this
in-flight request is counted twice as SCMD_STATE_INFLIGHT. This way causes
trouble in handling scsi error.
Fixes the issue by not iterating over stale request.
Cc: linux-scsi@vger.kernel.org
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Reported-by: luojiaxing <luojiaxing@huawei.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20210906065003.439019-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08dad2f4d5 ]
The Synopsys Ethernet IP uses the CSR clock as a base clock for MDC.
The divisor used is set in the MAC_MDIO_Address register field CR
(Clock Rate)
The divisor is there to change the CSR clock into a clock that falls
below the IEEE 802.3 specified max frequency of 2.5MHz.
If the CSR clock is 300MHz, the code falls back to using the reset
value in the MAC_MDIO_Address register, as described in the comment
above this code.
However, 300MHz is actually an allowed value and the proper divider
can be estimated quite easily (it's just 1Hz difference!)
A CSR frequency of 300MHz with the maximum clock rate value of 0x5
(STMMAC_CSR_250_300M, a divisor of 124) gives somewhere around
~2.42MHz which is below the IEEE 802.3 specified maximum.
For the ARTPEC-8 SoC, the CSR clock is this problematic 300MHz,
and unfortunately, the reset-value of the MAC_MDIO_Address CR field
is 0x0.
This leads to a clock rate of zero and a divisor of 42, and gives an
MDC frequency of ~7.14MHz.
Allow CSR clock of 300MHz by making the comparison inclusive.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d82d5303c4 ]
plat_dev->dev->platform_data is released by platform_device_unregister(),
use of pclk and hclk is a use-after-free. Since device unregister won't
need a clk device we adjust the function call sequence to fix this issue.
[ 31.261225] BUG: KASAN: use-after-free in macb_remove+0x77/0xc6 [macb_pci]
[ 31.275563] Freed by task 306:
[ 30.276782] platform_device_release+0x25/0x80
Suggested-by: Nicolas Ferre <Nicolas.Ferre@microchip.com>
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea269a6f72 ]
Currently changes to the advertising state via ethtool do not cause any
reselection of the configured interface mode after the SFP is already
inserted and initially configured.
While it is not typical to change the advertised link modes for an
interface using an SFP in certain use cases it is desirable. In the case
of a SFP port that is capable of handling both SFP and SFP+ modules it
will automatically select between 1G and 10G modes depending on the
supported mode of the SFP. However if the SFP module is capable of
working in multiple modes (e.g. a SFP+ DAC that can operate at 1G or
10G), one end of the cable may be attached to a SFP 1000base-x port thus
the SFP+ end must be manually configured to the 1000base-x mode in order
for the link to be established.
This change causes the ethtool setting of advertised mode changes to
reselect the interface mode so that the link can be established.
Additionally when a module is inserted the advertising mode is reset to
match the supported modes of the module.
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9990da93d2 ]
For each provided buffer, we allocate a struct io_buffer to hold the
data associated with it. As a large number of buffers can be provided,
account that data with memcg.
Fixes: ddf0322db7 ("io_uring: add IORING_OP_PROVIDE_BUFFERS")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c99720b28 ]
Add a missing __iomem annotation to address a sparse warning. The caller
is expected to pass an __iomem annotated pointer to this function. The
current usages send a 64-bytes command descriptor to an MMIO location
(portal) on a device for consumption.
Also, from the comment in movdir64b(), which also applies to enqcmds(),
@__dst must be supplied as an lvalue because this tells the compiler
what the object is (its size) the instruction accesses. I.e., not the
pointers but what they point to, thus the deref'ing '*'."
The actual sparse warning is:
drivers/dma/idxd/submit.c: note: in included file (through arch/x86/include/asm/processor.h, \
arch/x86/include/asm/timex.h, include/linux/timex.h, include/linux/time32.h, \
include/linux/time.h, include/linux/stat.h, ...):
./arch/x86/include/asm/special_insns.h:289:41: warning: incorrect type in initializer (different address spaces)
./arch/x86/include/asm/special_insns.h:289:41: expected struct <noident> *__dst
./arch/x86/include/asm/special_insns.h:289:41: got void [noderef] __iomem *dst
[ bp: Massage commit message. ]
Fixes: 7f5933f81b ("x86/asm: Add an enqcmds() wrapper for the ENQCMDS instruction")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lkml.kernel.org/r/161003789741.4062451.14362269365703761223.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7df835a32a ]
Commit b0140891a8 ("md: Fix race when creating a new md device.")
not only moved assigning mddev->gendisk before calling add_disk, which
fixes the races described in the commit log, but also added a
mddev->open_mutex critical section over add_disk and creation of the
md kobj. Adding a kobject after add_disk is racy vs deleting the gendisk
right after adding it, but md already prevents against that by holding
a mddev->active reference.
On the other hand taking this lock added a lock order reversal with what
is not disk->open_mutex (used to be bdev->bd_mutex when the commit was
added) for partition devices, which need that lock for the internal open
for the partition scan, and a recent commit also takes it for
non-partitioned devices, leading to further lockdep splatter.
Fixes: b0140891a8 ("md: Fix race when creating a new md device.")
Fixes: d626338735 ("block: support delayed holder registration")
Reported-by: syzbot+fadc0aaf497e6a493b9f@syzkaller.appspotmail.com
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: syzbot+fadc0aaf497e6a493b9f@syzkaller.appspotmail.com
Reviewed-by: NeilBrown <neilb@suse.de>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e946d3c887 ]
The problem is the mismatched types between "ctx->total_len" which is
an unsigned int, "rc" which is an int, and "ctx->rc" which is a
ssize_t. The code does:
ctx->rc = (rc == 0) ? ctx->total_len : rc;
We want "ctx->rc" to store the negative "rc" error code. But what
happens is that "rc" is type promoted to a high unsigned int and
'ctx->rc" will store the high positive value instead of a negative
value.
The fix is to change "rc" from an int to a ssize_t.
Fixes: c610c4b619 ("CIFS: Add asynchronous write support through kernel AIO")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1bb30b20b4 ]
After printing the list of thermal governors, then this function prints
a newline character. The problem is that "size" has not been updated
after printing the last governor. This means that it can write one
character (the NUL terminator) beyond the end of the buffer.
Get rid of the "size" variable and just use "PAGE_SIZE - count" directly.
Fixes: 1b4f48494e ("thermal: core: group functions related to governor handling")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210916131342.GB25094@kili
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 298ba0e3d4 ]
Various places in the nvme code that rely on ctrl->namespace to be
ordered. Ensure that the namespae is inserted into the list at the
right position from the start instead of sorting it after the fact.
Fixes: 540c801c65 ("NVMe: Implement namespace list scanning")
Reported-by: Anton Eidelman <anton.eidelman@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e371af033c ]
When the controller sends us multiple r2t PDUs in a single
request we need to account for it correctly as our send/recv
context run concurrently (i.e. we get a new r2t with r2t_offset
before we updated our iterator and req->data_sent marker). This
can cause wrong offsets to be sent to the controller.
To fix that, we will first know that this may happen only in
the send sequence of the last page, hence we will take
the r2t_offset to the h2c PDU data_offset, and in
nvme_tcp_try_send_data loop, we make sure to increment
the request markers also when we completed a PDU but
we are expecting more r2t PDUs as we still did not send
the entire data of the request.
Fixes: 825619b09a ("nvme-tcp: fix possible use-after-completion")
Reported-by: Nowak, Lukasz <Lukasz.Nowak@Dell.com>
Tested-by: Nowak, Lukasz <Lukasz.Nowak@Dell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 34331739e1 ]
Earlier successes leave 'ret' in a non error state, so these errors are
not reported. Set ret to -EINVAL before going to the error handler.
This addresses two issues reported by smatch:
drivers/fpga/machxo2-spi.c:229 machxo2_write_init()
warn: missing error code 'ret'
drivers/fpga/machxo2-spi.c:316 machxo2_write_complete()
warn: missing error code 'ret'
[mdf@kernel.org: Reworded commit message]
Fixes: 88fb3a0023 ("fpga: lattice machxo2: Add Lattice MachXO2 support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06e49073df ]
'set_signals()' in synclink_gt.c conflicts with an exported symbol
in arch/um/, so change set_signals() to set_gtsignals(). Keep
the function names similar by also changing get_signals() to
get_gtsignals().
../drivers/tty/synclink_gt.c:442:13: error: conflicting types for ‘set_signals’
static void set_signals(struct slgt_info *info);
^~~~~~~~~~~
In file included from ../include/linux/irqflags.h:16:0,
from ../include/linux/spinlock.h:58,
from ../include/linux/mm_types.h:9,
from ../include/linux/buildid.h:5,
from ../include/linux/module.h:14,
from ../drivers/tty/synclink_gt.c:46:
../arch/um/include/asm/irqflags.h:6:5: note: previous declaration of ‘set_signals’ was here
int set_signals(int enable);
^~~~~~~~~~~
Fixes: 705b6c7b34 ("[PATCH] new driver synclink_gt")
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20210902003806.17054-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef7ae7f746 ]
Commit 356ba2a8bc ("scsi: target: tcmu: Make pgr_support and alua_support
attributes writable") introduced support for changeable alua_support and
pgr_support target attributes. These can only be changed if the backstore
is user-backed, otherwise the kernel returns -EINVAL.
This triggers a warning in the targetcli/rtslib code when performing a
target restore that includes non-userbacked backstores:
# targetctl restore
Storage Object block/storage1: Cannot set attribute alua_support:
[Errno 22] Invalid argument, skipped
Storage Object block/storage1: Cannot set attribute pgr_support:
[Errno 22] Invalid argument, skipped
Fix this warning by returning an error code only if we are really going to
flip the PGR/ALUA bit in the transport_flags field, otherwise we will do
nothing and return success.
Return ENOSYS instead of EINVAL if the pgr/alua attributes can not be
changed, this way it will be possible for userspace to understand if the
operation failed because an invalid value has been passed to strtobool() or
because the attributes are fixed.
Fixes: 356ba2a8bc ("scsi: target: tcmu: Make pgr_support and alua_support attributes writable")
Link: https://lore.kernel.org/r/20210906151809.52811-1-mlombard@redhat.com
Reviewed-by: Bodo Stroesser <bostroesser@gmail.com>
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d88c339c4 ]
After fixing hibernation resume flow, another usecase was found which
should be explicitly handled - resume when device is in "down" state.
Invoke aq_nic_init jointly with aq_nic_start only if ndev was already
up during suspend/hibernate. We still need to perform nic_deinit() if
caller requests for it, to handle the freeze/resume scenarios.
Fixes: 57f780f1c4 ("atlantic: Fix driver resume flow.")
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fdbccea419 ]
Driver doesn't support aRFS for encapsulated packets, return early error
in such a case.
Fixes: 1eb8c695bd ("net/mlx4_en: Add accelerated RFS support")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ea7812326 ]
If the HW device is during recovery, the HW resources will never return,
hence we shouldn't wait for the CID (HW context ID) bitmaps to clear.
This fix speeds up the error recovery flow.
Fixes: 64515dc899 ("qed: Add infrastructure for error detection and recovery")
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 248f064af2 ]
When qeth_set_online() calls qeth_clear_working_pool_list() to roll
back after an error exit from qeth_hardsetup_card(), we are at risk of
accessing card->qdio.in_q before it was allocated by
qeth_alloc_qdio_queues() via qeth_mpc_initialize().
qeth_clear_working_pool_list() then dereferences NULL, and by writing to
queue->bufs[i].pool_entry scribbles all over the CPU's lowcore.
Resulting in a crash when those lowcore areas are used next (eg. on
the next machine-check interrupt).
Such a scenario would typically happen when the device is first set
online and its queues aren't allocated yet. An early IO error or certain
misconfigs (eg. mismatched transport mode, bad portno) then cause us to
error out from qeth_hardsetup_card() with card->qdio.in_q still being
NULL.
Fix it by checking the pointer for NULL before accessing it.
Note that we also have (rare) paths inside qeth_mpc_initialize() where
a configuration change can cause us to free the existing queues,
expecting that subsequent code will allocate them again. If we then
error out before that re-allocation happens, the same bug occurs.
Fixes: eff73e16ee ("s390/qeth: tolerate pre-filled RX buffer")
Reported-by: Stefan Raspl <raspl@linux.ibm.com>
Root-caused-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e3dbf765f ]
During initialization of a signal testcase, features declared as required
are properly checked against the running system but no action is then taken
to effectively skip such a testcase.
Fix core signals test logic to abort initialization and report such a
testcase as skipped to the KSelfTest framework.
Fixes: f96bf43403 ("kselftest: arm64: mangle_pstate_invalid_compat_toggle and common utils")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210920121228.35368-1-cristian.marussi@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 74b6d7d133 ]
The Linux device model permits both the ->shutdown and ->remove driver
methods to get called during a shutdown procedure. Example: a DSA switch
which sits on an SPI bus, and the SPI bus driver calls this on its
->shutdown method:
spi_unregister_controller
-> device_for_each_child(&ctlr->dev, NULL, __unregister);
-> spi_unregister_device(to_spi_device(dev));
-> device_del(&spi->dev);
So this is a simple pattern which can theoretically appear on any bus,
although the only other buses on which I've been able to find it are
I2C:
i2c_del_adapter
-> device_for_each_child(&adap->dev, NULL, __unregister_client);
-> i2c_unregister_device(client);
-> device_unregister(&client->dev);
The implication of this pattern is that devices on these buses can be
unregistered after having been shut down. The drivers for these devices
might choose to return early either from ->remove or ->shutdown if the
other callback has already run once, and they might choose that the
->shutdown method should only perform a subset of the teardown done by
->remove (to avoid unnecessary delays when rebooting).
So in other words, the device driver may choose on ->remove to not
do anything (therefore to not unregister an MDIO bus it has registered
on ->probe), because this ->remove is actually triggered by the
device_shutdown path, and its ->shutdown method has already run and done
the minimally required cleanup.
This used to be fine until the blamed commit, but now, the following
BUG_ON triggers:
void mdiobus_free(struct mii_bus *bus)
{
/* For compatibility with error handling in drivers. */
if (bus->state == MDIOBUS_ALLOCATED) {
kfree(bus);
return;
}
BUG_ON(bus->state != MDIOBUS_UNREGISTERED);
bus->state = MDIOBUS_RELEASED;
put_device(&bus->dev);
}
In other words, there is an attempt to free an MDIO bus which was not
unregistered. The attempt to free it comes from the devres release
callbacks of the SPI device, which are executed after the device is
unregistered.
I'm not saying that the fact that MDIO buses allocated using devres
would automatically get unregistered wasn't strange. I'm just saying
that the commit didn't care about auditing existing call paths in the
kernel, and now, the following code sequences are potentially buggy:
(a) devm_mdiobus_alloc followed by plain mdiobus_register, for a device
located on a bus that unregisters its children on shutdown. After
the blamed patch, either both the alloc and the register should use
devres, or none should.
(b) devm_mdiobus_alloc followed by plain mdiobus_register, and then no
mdiobus_unregister at all in the remove path. After the blamed
patch, nobody unregisters the MDIO bus anymore, so this is even more
buggy than the previous case which needs a specific bus
configuration to be seen, this one is an unconditional bug.
In this case, the Realtek drivers fall under category (b). To solve it,
we can register the MDIO bus under devres too, which restores the
previous behavior.
Fixes: ac3a68d566 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Reported-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Reported-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5135e96a3d ]
The Linux device model permits both the ->shutdown and ->remove driver
methods to get called during a shutdown procedure. Example: a DSA switch
which sits on an SPI bus, and the SPI bus driver calls this on its
->shutdown method:
spi_unregister_controller
-> device_for_each_child(&ctlr->dev, NULL, __unregister);
-> spi_unregister_device(to_spi_device(dev));
-> device_del(&spi->dev);
So this is a simple pattern which can theoretically appear on any bus,
although the only other buses on which I've been able to find it are
I2C:
i2c_del_adapter
-> device_for_each_child(&adap->dev, NULL, __unregister_client);
-> i2c_unregister_device(client);
-> device_unregister(&client->dev);
The implication of this pattern is that devices on these buses can be
unregistered after having been shut down. The drivers for these devices
might choose to return early either from ->remove or ->shutdown if the
other callback has already run once, and they might choose that the
->shutdown method should only perform a subset of the teardown done by
->remove (to avoid unnecessary delays when rebooting).
So in other words, the device driver may choose on ->remove to not
do anything (therefore to not unregister an MDIO bus it has registered
on ->probe), because this ->remove is actually triggered by the
device_shutdown path, and its ->shutdown method has already run and done
the minimally required cleanup.
This used to be fine until the blamed commit, but now, the following
BUG_ON triggers:
void mdiobus_free(struct mii_bus *bus)
{
/* For compatibility with error handling in drivers. */
if (bus->state == MDIOBUS_ALLOCATED) {
kfree(bus);
return;
}
BUG_ON(bus->state != MDIOBUS_UNREGISTERED);
bus->state = MDIOBUS_RELEASED;
put_device(&bus->dev);
}
In other words, there is an attempt to free an MDIO bus which was not
unregistered. The attempt to free it comes from the devres release
callbacks of the SPI device, which are executed after the device is
unregistered.
I'm not saying that the fact that MDIO buses allocated using devres
would automatically get unregistered wasn't strange. I'm just saying
that the commit didn't care about auditing existing call paths in the
kernel, and now, the following code sequences are potentially buggy:
(a) devm_mdiobus_alloc followed by plain mdiobus_register, for a device
located on a bus that unregisters its children on shutdown. After
the blamed patch, either both the alloc and the register should use
devres, or none should.
(b) devm_mdiobus_alloc followed by plain mdiobus_register, and then no
mdiobus_unregister at all in the remove path. After the blamed
patch, nobody unregisters the MDIO bus anymore, so this is even more
buggy than the previous case which needs a specific bus
configuration to be seen, this one is an unconditional bug.
In this case, DSA falls into category (a), it tries to be helpful and
registers an MDIO bus on behalf of the switch, which might be on such a
bus. I've no idea why it does it under devres.
It does this on probe:
if (!ds->slave_mii_bus && ds->ops->phy_read)
alloc and register mdio bus
and this on remove:
if (ds->slave_mii_bus && ds->ops->phy_read)
unregister mdio bus
I _could_ imagine using devres because the condition used on remove is
different than the condition used on probe. So strictly speaking, DSA
cannot determine whether the ds->slave_mii_bus it sees on remove is the
ds->slave_mii_bus that _it_ has allocated on probe. Using devres would
have solved that problem. But nonetheless, the existing code already
proceeds to unregister the MDIO bus, even though it might be
unregistering an MDIO bus it has never registered. So I can only guess
that no driver that implements ds->ops->phy_read also allocates and
registers ds->slave_mii_bus itself.
So in that case, if unregistering is fine, freeing must be fine too.
Stop using devres and free the MDIO bus manually. This will make devres
stop attempting to free a still registered MDIO bus on ->shutdown.
Fixes: ac3a68d566 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Reported-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a18cee4791 ]
The abort_work is scheduled when a connection was detected to be
out-of-sync after a link failure. The work calls smc_conn_kill(),
which calls smc_close_active_abort() and that might end up calling
smc_close_cancel_work().
smc_close_cancel_work() cancels any pending close_work and tx_work but
needs to release the sock_lock before and acquires the sock_lock again
afterwards. So when the sock_lock was NOT acquired before then it may
be held after the abort_work completes. Thats why the sock_lock is
acquired before the call to smc_conn_kill() in __smc_lgr_terminate(),
but this is missing in smc_conn_abort_work().
Fix that by acquiring the sock_lock first and release it after the
call to smc_conn_kill().
Fixes: b286a0651e ("net/smc: handle incoming CDC validation message")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63b1279d99 ]
The input parameters may not be reliable. Before using the
queue id, we should check this parameter. Otherwise, memory
overwriting may occur.
Fixes: d341001846 ("net: hns3: refactor the mailbox message between PF and VF")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e184cec5e2 ]
When user change rss 'hfunc' without set rss 'hkey' by ethtool
-X command, the driver will ignore the 'hfunc' for the hkey is
NULL. It's unreasonable. So fix it.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Fixes: 374ad29176 ("net: hns3: Add RSS general configuration support for VF")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5bed8b0704 ]
The smallest TX ring size we support must fit a TX SKB with MAX_SKB_FRAGS
+ 1. Because the first TX BD for a packet is always a long TX BD, we
need an extra TX BD to fit this packet. Define BNXT_MIN_TX_DESC_CNT with
this value to make this more clear. The current code uses a minimum
that is off by 1. Fix it using this constant.
The tx_wake_thresh to determine when to wake up the TX queue is half the
ring size but we must have at least BNXT_MIN_TX_DESC_CNT for the next
packet which may have maximum fragments. So the comparison of the
available TX BDs with tx_wake_thresh should be >= instead of > in the
current code. Otherwise, at the smallest ring size, we will never wake
up the TX queue and will cause TX timeout.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f7afa05c9 ]
The only struct dim_sample member that does not get
initialized by dim_update_sample() is comp_ctr. (There
is special API to initialize comp_ctr:
dim_update_sample_with_comps(), and it is currently used
only for RDMA.) comp_ctr is used to compute curr_stats->cmps
and curr_stats->cpe_ratio (see dim_calc_stats()) which in
turn are consumed by the rdma_dim_*() API. Therefore,
functionally, the net_dim*() API consumers are not affected.
Nevertheless, fix the computation of statistics based
on an uninitialized variable, even if the mentioned statistics
are not used at the moment.
Fixes: ae0e6a5d16 ("enetc: Add adaptive interrupt coalescing")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7237a494de ]
irq_set_affinity_hit() stores a reference to the cpumask_t
parameter in the irq descriptor, and that reference can be
accessed later from irq_affinity_hint_proc_show(). Since
the cpu_mask parameter passed to irq_set_affinity_hit() has
only temporary storage (it's on the stack memory), later
accesses to it are illegal. Thus reads from the corresponding
procfs affinity_hint file can result in paging request oops.
The issue is fixed by the get_cpu_mask() helper, which provides
a permanent storage for the cpumask_t parameter.
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d37e1cab2 ]
When an afs file or directory is modified locally such that the total file
size is extended, i_blocks needs to be recalculated too.
Fix this by making afs_write_end() and afs_edit_dir_add() call
afs_set_i_size() rather than setting inode->i_size directly as that also
recalculates inode->i_blocks.
This can be tested by creating and writing into directories and files and
then examining them with du. Without this change, directories show a 4
blocks (they start out at 2048 bytes) and files show 0 blocks; with this
change, they should show a number of blocks proportional to the file size
rounded up to 1024.
Fixes: 31143d5d51 ("AFS: implement basic file write support")
Fixes: 63a4681ff3 ("afs: Locally edit directory data for mkdir/create/unlink/...")
Reported-by: Markus Suvanto <markus.suvanto@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
Tested-by: Markus Suvanto <markus.suvanto@gmail.com>
cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/r/163113612442.352844.11162345591911691150.stgit@warthog.procyon.org.uk/
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63d49d843e ]
The AFS filesystem is currently triggering the silly-rename cleanup from
afs_d_revalidate() when it sees that a dentry has been changed by a third
party[1]. It should not be doing this as the cleanup includes deleting the
silly-rename target file on iput.
Fix this by removing the places in the d_revalidate handling that validate
anything other than the directory and the dirent. It probably should not
be looking to validate the target inode of the dentry also.
This includes removing the point in afs_d_revalidate() where the inode that
a dentry used to point to was marked as being deleted (AFS_VNODE_DELETED).
We don't know it got deleted. It could have been renamed or it could have
hard links remaining.
This was reproduced by cloning a git repo onto an afs volume on one
machine, switching to another machine and doing "git status", then
switching back to the first and doing "git status". The second status
would show weird output due to ".git/index" getting deleted by the above
mentioned mechanism.
A simpler way to do it is to do:
machine 1: touch a
machine 2: touch b; mv -f b a
machine 1: stat a
on an afs volume. The bug shows up as the stat failing with ENOENT and the
file server log showing that machine 1 deleted "a".
Fixes: 79ddbfa500 ("afs: Implement sillyrename for unlink and rename")
Reported-by: Markus Suvanto <markus.suvanto@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Markus Suvanto <markus.suvanto@gmail.com>
cc: linux-afs@lists.infradead.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=214217#c4 [1]
Link: https://lore.kernel.org/r/163111668100.283156.3851669884664475428.stgit@warthog.procyon.org.uk/
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e8f69b16ee upstream.
If resource allocation and registration fail for a muxed tty device
(e.g. if there are no more minor numbers) the driver should not try to
deregister the never-registered (or already-deregistered) tty.
Fix up the error handling to avoid dereferencing a NULL pointer when
attempting to remove the character device.
Fixes: 72dc1c096c ("HSO: add option hso driver")
Cc: stable@vger.kernel.org # 2.6.27
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab39d3cef5 upstream.
Update the current state as boot state during dpm initialization.
During the subsequent initialization, set_power_state gets called to
transition to the final power state. set_power_state refers to values
from the current state and without current state populated, it could
result in NULL pointer dereference.
For ex: on platforms where PCI speed change is supported through ACPI
ATCS method, the link speed of current state needs to be queried before
deciding on changing to final power state's link speed. The logic to query
ATCS-support was broken on certain platforms. The issue became visible
when broken ATCS-support logic got fixed with commit
f9b7f3703f ("drm/amdgpu/acpi: make ATPX/ATCS structures global (v2)").
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1698
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7215e90981 upstream.
Reporting zones on a SCSI device sometimes fail with the following error:
[76248.516390] ata16.00: invalid transfer count 131328
[76248.523618] sd 15:0:0:0: [sda] REPORT ZONES start lba 536870912 failed
The error (from drivers/ata/libata-scsi.c:ata_scsi_zbc_in_xlat()) indicates
that buffer size is not aligned to SECTOR_SIZE.
This happens when the __vmalloc() failed. Consider we are reporting 4096
zones, then we will have "bufsize = roundup((4096 + 1) * 64,
SECTOR_SIZE)" = (513 * 512) = 262656. Then, __vmalloc() failure halves
the bufsize to 131328, which is no longer aligned to SECTOR_SIZE.
Use rounddown() to ensure the size is always aligned to SECTOR_SIZE and fix
the comment as well.
Link: https://lore.kernel.org/r/20210906140642.2267569-1-naohiro.aota@wdc.com
Fixes: 23a50861ad ("scsi: sd_zbc: Cleanup sd_zbc_alloc_report_buffer()")
Cc: stable@vger.kernel.org # 5.5+
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 74e1eb3b4a upstream.
Driver's tx_empty callback should signal when the transmit shift register
is empty. So when the last character has been sent.
STAT_TX_FIFO_EMP bit signals only that HW transmit FIFO is empty, which
happens when the last byte is loaded into transmit shift register.
STAT_TX_EMP bit signals when the both HW transmit FIFO and transmit shift
register are empty.
So replace STAT_TX_FIFO_EMP check by STAT_TX_EMP in mvebu_uart_tx_empty()
callback function.
Fixes: 30530791a7 ("serial: mvebu-uart: initial support for Armada-3700 serial port")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20210911132017.25505-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58877b0824 upstream.
It has been observed with certain PCIe USB cards (like Inateck connected
to AM64 EVM or J7200 EVM) that as soon as the primary roothub is
registered, port status change is handled even before xHC is running
leading to cold plug USB devices not detected. For such cases, registering
both the root hubs along with the second HCD is required. Add support for
deferring roothub registration in usb_add_hcd(), so that both primary and
secondary roothubs are registered along with the second HCD.
CC: stable@vger.kernel.org # 5.4+
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210909064200.16216-2-kishon@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8cfac9a674 upstream.
After we start to do core soft reset while usb role switch,
the phy init is invoked at every switch to device mode, but
its counter part de-init is missing, this causes the actual
phy init can not be done when we really want to re-init phy
like system resume, because the counter maintained by phy
core is not 0. considering phy init is actually redundant for
role switch, so move out the phy init from core soft reset to
dwc3 core init where is the only place required.
Fixes: f88359e158 ("usb: dwc3: core: Do core softreset when switch mode")
Cc: <stable@vger.kernel.org>
Tested-by: faqiang.zhu <faqiang.zhu@nxp.com>
Tested-by: John Stultz <john.stultz@linaro.org> #HiKey960
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/1631068099-13559-1-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5fdb55c1ac upstream.
During BC_FREE_BUFFER processing, the BINDER_TYPE_FDA object
cleanup may close 1 or more fds. The close operations are
completed using the task work mechanism -- which means the thread
needs to return to userspace or the file object may never be
dereferenced -- which can lead to hung processes.
Force the binder thread back to userspace if an fd is closed during
BC_FREE_BUFFER handling.
Fixes: 80cd795630 ("binder: fix use-after-free due to ksys_close() during fdget()")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Martijn Coenen <maco@android.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Todd Kjos <tkjos@google.com>
Link: https://lore.kernel.org/r/20210830195146.587206-1-tkjos@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d91adc5322 upstream.
This reverts commit f3de5d857b.
That commit broke USB on all routers that have USB always powered on and
don't require toggling any GPIO. It's a majority of devices actually.
The original code worked and seemed safe: vcc GPIO is optional and
bcma_hci_platform_power_gpio() takes care of checking the pointer before
using it.
This revert fixes:
[ 10.801127] bcma_hcd: probe of bcma0:11 failed with error -2
Fixes: f3de5d857b ("USB: bcma: Add a check for devm_gpiod_get")
Cc: stable <stable@vger.kernel.org>
Cc: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20210831065419.18371-1-zajec5@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b55d37ef6b upstream.
ScanLogic SL11R-IDE with firmware older than 2.6c (the latest one) has
broken tag handling, preventing the device from working at all:
usb 1-1: new full-speed USB device number 2 using uhci_hcd
usb 1-1: New USB device found, idVendor=04ce, idProduct=0002, bcdDevice= 2.60
usb 1-1: New USB device strings: Mfr=1, Product=1, SerialNumber=0
usb 1-1: Product: USB Device
usb 1-1: Manufacturer: USB Device
usb-storage 1-1:1.0: USB Mass Storage device detected
scsi host2: usb-storage 1-1:1.0
usbcore: registered new interface driver usb-storage
usb 1-1: reset full-speed USB device number 2 using uhci_hcd
usb 1-1: reset full-speed USB device number 2 using uhci_hcd
usb 1-1: reset full-speed USB device number 2 using uhci_hcd
usb 1-1: reset full-speed USB device number 2 using uhci_hcd
Add US_FL_BULK_IGNORE_TAG to fix it. Also update my e-mail address.
2.6c is the only firmware that claims Linux compatibility.
The firmware can be upgraded using ezotgdbg utility:
https://github.com/asciilifeform/ezotgdbg
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ondrej Zary <linux@zary.sk>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210913210106.12717-1-linux@zary.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0594c58161 upstream.
The initial observation was that in PV mode under Xen 32-bit user space
didn't work anymore. Attempts of system calls ended in #GP(0x402). All
of the sudden the vector 0x80 handler was not in place anymore. As it
turns out up to 5.13 redundant initialization did occur: Once from
cpu_initialize_context() (through its VCPUOP_initialise hypercall) and a
2nd time while each CPU was brought fully up. This 2nd initialization is
now gone, uncovering that the 1st one was flawed: Unlike for the
set_trap_table hypercall, a full virtual IDT needs to be specified here;
the "vector" fields of the individual entries are of no interest. With
many (kernel) IDT entries still(?) (i.e. at that point at least) empty,
the syscall vector 0x80 ended up in slot 0x20 of the virtual IDT, thus
becoming the domain's handler for vector 0x20.
Make xen_convert_trap_info() fit for either purpose, leveraging the fact
that on the xen_copy_trap_info() path the table starts out zero-filled.
This includes moving out the writing of the sentinel, which would also
have lead to a buffer overrun in the xen_copy_trap_info() case if all
(kernel) IDT entries were populated. Convert the writing of the sentinel
to clearing of the entire table entry rather than just the address
field.
(I didn't bother trying to identify the commit which uncovered the issue
in 5.14; the commit named below is the one which actually introduced the
bad code.)
Fixes: f87e4cac4f ("xen: SMP guest support")
Cc: stable@vger.kernel.org
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/7a266932-092e-b68f-f2bb-1473b61adc6e@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ed38fd4a1 upstream.
Although very unlikely that the tlink pointer would be null in this case,
get_next_mid function can in theory return null (but not an error)
so need to check for null (not for IS_ERR, which can not be returned
here).
Address warning:
fs/smbfs_client/connect.c:2392 cifs_match_super()
warn: 'tlink' isn't an ERR_PTR
Pointed out by Dan Carpenter via smatch code analysis tool
CC: stable@vger.kernel.org
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 91bb163e1e upstream.
According USB spec each ISOC transaction should be performed in a
designated for that transaction interval. On bus errors or delays
in operating system scheduling of client software can result in no
packet being transferred for a (micro)frame. An error indication
should be returned as status to the client software in such a case.
Current implementation in case of missed/dropped interval send same
data in next possible interval instead of reporting missed isoc.
This fix complete requests with -ENODATA if interval elapsed.
HSOTG core in BDMA and Slave modes haven't HW support for
(micro)frames tracking, this is why SW should care about tracking
of (micro)frames. Because of that method and consider operating
system scheduling delays, added few additional checking's of elapsed
target (micro)frame:
1. Immediately before enabling EP to start transfer.
2. With any transfer completion interrupt.
3. With incomplete isoc in/out interrupt.
4. With EP disabled interrupt because of incomplete transfer.
5. With OUT token received while EP disabled interrupt (for OUT
transfers).
6. With NAK replied to IN token interrupt (for IN transfers).
As part of ISOC flow, additionally fixed 'current' and 'target' frame
calculation functions. In HS mode SOF limits provided by DSTS register
is 0x3fff, but in non HS mode this limit is 0x7ff.
Tested by internal tool which also using for dwc3 testing.
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/95d1423adf4b0f68187c9894820c4b7e964a3f7f.1631175721.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bcbda81020 upstream.
We get an unexpected value of /proc/sys/vm/overcommit_memory after
running the following program:
int main()
{
int fd = open("/proc/sys/vm/overcommit_memory", O_RDWR);
write(fd, "1", 1);
write(fd, "2", 1);
close(fd);
}
write(fd, "2", 1) will pass *ppos = 1 to proc_dointvec_minmax.
proc_dointvec_minmax will return 0 without setting new_policy.
t.data = &new_policy;
ret = proc_dointvec_minmax(&t, write, buffer, lenp, ppos)
-->do_proc_dointvec
-->__do_proc_dointvec
if (write) {
if (proc_first_pos_non_zero_ignore(ppos, table))
goto out;
sysctl_overcommit_memory = new_policy;
so sysctl_overcommit_memory will be set to an uninitialized value.
Check whether new_policy has been changed by proc_dointvec_minmax.
Link: https://lkml.kernel.org/r/20210923020524.13289-1-chenjun102@huawei.com
Fixes: 56f3547bfa ("mm: adjust vm_committed_as_batch according to vm overcommit policy")
Signed-off-by: Chen Jun <chenjun102@huawei.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Feng Tang <feng.tang@intel.com>
Reviewed-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Rui Xiang <rui.xiang@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b58db229eb617d97d5746113b77045f1f884bcb upstream.
Measurements in different conditions showed that aardvark hardware PIO
response can take up to 1.44s. Increase wait timeout from 1ms to 1.5s to
ensure that we do not miss responses from hardware. After 1.44s hardware
returns errors (e.g. Completer abort).
The previous two patches fixed checking for PIO status, so now we can use
it to also catch errors which are reported by hardware after 1.44s.
After applying this patch, kernel can detect and print PIO errors to dmesg:
[ 6.879999] advk-pcie d0070000.pcie: Non-posted PIO Response Status: CA, 0xe00 @ 0x100004
[ 6.896436] advk-pcie d0070000.pcie: Posted PIO Response Status: COMP_ERR, 0x804 @ 0x100004
[ 6.913049] advk-pcie d0070000.pcie: Posted PIO Response Status: COMP_ERR, 0x804 @ 0x100010
[ 6.929663] advk-pcie d0070000.pcie: Non-posted PIO Response Status: CA, 0xe00 @ 0x100010
[ 6.953558] advk-pcie d0070000.pcie: Posted PIO Response Status: COMP_ERR, 0x804 @ 0x100014
[ 6.970170] advk-pcie d0070000.pcie: Non-posted PIO Response Status: CA, 0xe00 @ 0x100014
[ 6.994328] advk-pcie d0070000.pcie: Posted PIO Response Status: COMP_ERR, 0x804 @ 0x100004
Without this patch kernel prints only a generic error to dmesg:
[ 5.246847] advk-pcie d0070000.pcie: config read/write timed out
Link: https://lore.kernel.org/r/20210722144041.12661-3-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org # 7fbcb5da81 ("PCI: aardvark: Don't rely on jiffies while holding spinlock")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Linux support for controlling card power via regulators appears to
be contentious. I would argue that the default behaviour is contrary to
the SDHCI spec - turning off the power writes a reserved value to the
SD Bus Voltage Select field of the Power Control Register, which
seems to kill the Arasan/iProc controller - but fortunately there is a
hook in sdhci_ops to override the behaviour.
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
This reverts commit aed19399a0.
Commit 6c92ae1e45 ("mmc: sdhci: Introduce sdhci_set_power_and_bus_voltage()")
introduced a generic helper that does the same thing so use that instead in
the following commit.
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
Check for errors only if we actually tried to enable the bvb clock.
Fixes: 01a6d727b4 ("vc4/drm: hdmi: Handle case when bvb clock is null")
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
When doing an asynchronous page flip (PAGE_FLIP ioctl with the
DRM_MODE_PAGE_FLIP_ASYNC flag set), the current code waits for the
possible GPU buffer being rendered through a call to
vc4_queue_seqno_cb().
On the BCM2835-37, the GPU driver is part of the vc4 driver and that
function is defined in vc4_gem.c to wait for the buffer to be rendered,
and once it's done, call a callback.
However, on the BCM2711 used on the RaspberryPi4, the GPU driver is
separate (v3d) and that function won't do anything. This was working
because we were going into a path, due to uninitialized variables, that
was always scheduling the callback.
However, we were never actually waiting for the buffer to be rendered
which was resulting in frames being displayed out of order.
The generic API to signal those kind of completion in the kernel are the
DMA fences, and fortunately the v3d drivers supports them and signal
when its job is done. That API also provides an equivalent function that
allows to have a callback being executed when the fence is signalled as
done.
Let's change our driver a bit to rely on the previous function for the
older SoCs, and on DMA fences for the BCM2711.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The read and write functions did not use the correct pointer offset
when dealing with an odd number of bytes after a DMA transfer. Also,
only handle the remaining odd bytes if the DMA transfer completed
successfully.
Submitted-by: @madimario (GitHub)
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The driver was implementing a get_brightness function that
tried to read back the PWM setting of the display to report
as the current brightness.
The controller on the display does not support that, therefore
we end up reporting a brightness of 0, and that confuses
systemd's backlight service.
Remove the hook so that the framework returns the current
brightness automatically.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
This allows using the video-i2c camera driver with MLX90640 thermal
infrared sensors, connected to Raspberry Pi. CONFIG_VIDEO_V4L2_I2C
has to be selected to use the camera.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
commit e8f71f8923 upstream.
nvkm test builds fail with the following error.
drivers/gpu/drm/nouveau/nvkm/engine/device/ctrl.c: In function 'nvkm_control_mthd_pstate_info':
drivers/gpu/drm/nouveau/nvkm/engine/device/ctrl.c:60:35: error: overflow in conversion from 'int' to '__s8' {aka 'signed char'} changes value from '-251' to '5'
The code builds on most architectures, but fails on parisc where ENOSYS
is defined as 251.
Replace the error code with -ENODEV (-19). The actual error code does
not really matter and is not passed to userspace - it just has to be
negative.
Fixes: 7238eca4cf ("drm/nouveau: expose pstate selection per-power source in sysfs")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9848417926 ]
The intel powerclamp driver will setup a per-CPU worker with RT
priority. The worker will then invoke play_idle() in which it remains in
the idle poll loop until it is stopped by the timer it started earlier.
That timer needs to expire in hard interrupt context on PREEMPT_RT.
Otherwise the timer will expire in ksoftirqd as a SOFT timer but that task
won't be scheduled on the CPU because its priority is lower than the
priority of the worker which is in the idle loop.
Always expire the idle timer in hard interrupt context.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210906113034.jgfxrjdvxnjqgtmc@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 884f0e84f1 ]
The pending timer has been set up in blk_throtl_init(). However, the
timer is not deleted in blk_throtl_exit(). This means that the timer
handler may still be running after freeing the timer, which would
result in a use-after-free.
Fix by calling del_timer_sync() to delete the timer in blk_throtl_exit().
Signed-off-by: Li Jinlin <lijinlin3@huawei.com>
Link: https://lore.kernel.org/r/20210907121242.2885564-1-lijinlin3@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d44084c934 ]
A consumer is expected to disable a PWM before calling pwm_put(). And if
they didn't there is hopefully a good reason (or the consumer needs
fixing). Also if disabling an enabled PWM was the right thing to do,
this should better be done in the framework instead of in each low level
driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d768cd7fd ]
A consumer is expected to disable a PWM before calling pwm_put(). And if
they didn't there is hopefully a good reason (or the consumer needs
fixing). Also if disabling an enabled PWM was the right thing to do,
this should better be done in the framework instead of in each low level
driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c68eb29c8e ]
A consumer is expected to disable a PWM before calling pwm_put(). And if
they didn't there is hopefully a good reason (or the consumer needs
fixing). Also if disabling an enabled PWM was the right thing to do,
this should better be done in the framework instead of in each low level
driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6c849012b ]
Currently there is no validity check for event ID received from F/W,
Thus exposing driver to memory overrun.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f5dec07ac ]
Patch series "nilfs2: fix incorrect usage of kobject".
This patchset from Nanyong Sun fixes memory leak issues and a NULL
pointer dereference issue caused by incorrect usage of kboject in nilfs2
sysfs implementation.
This patch (of 6):
Reported by syzkaller:
BUG: memory leak
unreferenced object 0xffff888100ca8988 (size 8):
comm "syz-executor.1", pid 1930, jiffies 4294745569 (age 18.052s)
hex dump (first 8 bytes):
6c 6f 6f 70 31 00 ff ff loop1...
backtrace:
kstrdup+0x36/0x70 mm/util.c:60
kstrdup_const+0x35/0x60 mm/util.c:83
kvasprintf_const+0xf1/0x180 lib/kasprintf.c:48
kobject_set_name_vargs+0x56/0x150 lib/kobject.c:289
kobject_add_varg lib/kobject.c:384 [inline]
kobject_init_and_add+0xc9/0x150 lib/kobject.c:473
nilfs_sysfs_create_device_group+0x150/0x7d0 fs/nilfs2/sysfs.c:986
init_nilfs+0xa21/0xea0 fs/nilfs2/the_nilfs.c:637
nilfs_fill_super fs/nilfs2/super.c:1046 [inline]
nilfs_mount+0x7b4/0xe80 fs/nilfs2/super.c:1316
legacy_get_tree+0x105/0x210 fs/fs_context.c:592
vfs_get_tree+0x8e/0x2d0 fs/super.c:1498
do_new_mount fs/namespace.c:2905 [inline]
path_mount+0xf9b/0x1990 fs/namespace.c:3235
do_mount+0xea/0x100 fs/namespace.c:3248
__do_sys_mount fs/namespace.c:3456 [inline]
__se_sys_mount fs/namespace.c:3433 [inline]
__x64_sys_mount+0x14b/0x1f0 fs/namespace.c:3433
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3b/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
If kobject_init_and_add return with error, then the cleanup of kobject
is needed because memory may be allocated in kobject_init_and_add
without freeing.
And the place of cleanup_dev_kobject should use kobject_put to free the
memory associated with the kobject. As the section "Kobject removal" of
"Documentation/core-api/kobject.rst" says, kobject_del() just makes the
kobject "invisible", but it is not cleaned up. And no more cleanup will
do after cleanup_dev_kobject, so kobject_put is needed here.
Link: https://lkml.kernel.org/r/1625651306-10829-1-git-send-email-konishi.ryusuke@gmail.com
Link: https://lkml.kernel.org/r/1625651306-10829-2-git-send-email-konishi.ryusuke@gmail.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Link: https://lkml.kernel.org/r/20210629022556.3985106-2-sunnanyong@huawei.com
Signed-off-by: Nanyong Sun <sunnanyong@huawei.com>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f96a5bfa1 ]
We update the ctime/mtime of a block device when we remove it so that
blkid knows the device changed. However we do this by re-opening the
block device and calling filp_update_time. This is more correct because
it'll call the inode->i_op->update_time if it exists, but the block dev
inodes do not do this. Instead call generic_update_time() on the
bd_inode in order to avoid the blkdev_open path and get rid of the
following lockdep splat:
======================================================
WARNING: possible circular locking dependency detected
5.14.0-rc2+ #406 Not tainted
------------------------------------------------------
losetup/11596 is trying to acquire lock:
ffff939640d2f538 ((wq_completion)loop0){+.+.}-{0:0}, at: flush_workqueue+0x67/0x5e0
but task is already holding lock:
ffff939655510c68 (&lo->lo_mutex){+.+.}-{3:3}, at: __loop_clr_fd+0x41/0x660 [loop]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #4 (&lo->lo_mutex){+.+.}-{3:3}:
__mutex_lock+0x7d/0x750
lo_open+0x28/0x60 [loop]
blkdev_get_whole+0x25/0xf0
blkdev_get_by_dev.part.0+0x168/0x3c0
blkdev_open+0xd2/0xe0
do_dentry_open+0x161/0x390
path_openat+0x3cc/0xa20
do_filp_open+0x96/0x120
do_sys_openat2+0x7b/0x130
__x64_sys_openat+0x46/0x70
do_syscall_64+0x38/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
-> #3 (&disk->open_mutex){+.+.}-{3:3}:
__mutex_lock+0x7d/0x750
blkdev_get_by_dev.part.0+0x56/0x3c0
blkdev_open+0xd2/0xe0
do_dentry_open+0x161/0x390
path_openat+0x3cc/0xa20
do_filp_open+0x96/0x120
file_open_name+0xc7/0x170
filp_open+0x2c/0x50
btrfs_scratch_superblocks.part.0+0x10f/0x170
btrfs_rm_device.cold+0xe8/0xed
btrfs_ioctl+0x2a31/0x2e70
__x64_sys_ioctl+0x80/0xb0
do_syscall_64+0x38/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
-> #2 (sb_writers#12){.+.+}-{0:0}:
lo_write_bvec+0xc2/0x240 [loop]
loop_process_work+0x238/0xd00 [loop]
process_one_work+0x26b/0x560
worker_thread+0x55/0x3c0
kthread+0x140/0x160
ret_from_fork+0x1f/0x30
-> #1 ((work_completion)(&lo->rootcg_work)){+.+.}-{0:0}:
process_one_work+0x245/0x560
worker_thread+0x55/0x3c0
kthread+0x140/0x160
ret_from_fork+0x1f/0x30
-> #0 ((wq_completion)loop0){+.+.}-{0:0}:
__lock_acquire+0x10ea/0x1d90
lock_acquire+0xb5/0x2b0
flush_workqueue+0x91/0x5e0
drain_workqueue+0xa0/0x110
destroy_workqueue+0x36/0x250
__loop_clr_fd+0x9a/0x660 [loop]
block_ioctl+0x3f/0x50
__x64_sys_ioctl+0x80/0xb0
do_syscall_64+0x38/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
other info that might help us debug this:
Chain exists of:
(wq_completion)loop0 --> &disk->open_mutex --> &lo->lo_mutex
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&lo->lo_mutex);
lock(&disk->open_mutex);
lock(&lo->lo_mutex);
lock((wq_completion)loop0);
*** DEADLOCK ***
1 lock held by losetup/11596:
#0: ffff939655510c68 (&lo->lo_mutex){+.+.}-{3:3}, at: __loop_clr_fd+0x41/0x660 [loop]
stack backtrace:
CPU: 1 PID: 11596 Comm: losetup Not tainted 5.14.0-rc2+ #406
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.13.0-2.fc32 04/01/2014
Call Trace:
dump_stack_lvl+0x57/0x72
check_noncircular+0xcf/0xf0
? stack_trace_save+0x3b/0x50
__lock_acquire+0x10ea/0x1d90
lock_acquire+0xb5/0x2b0
? flush_workqueue+0x67/0x5e0
? lockdep_init_map_type+0x47/0x220
flush_workqueue+0x91/0x5e0
? flush_workqueue+0x67/0x5e0
? verify_cpu+0xf0/0x100
drain_workqueue+0xa0/0x110
destroy_workqueue+0x36/0x250
__loop_clr_fd+0x9a/0x660 [loop]
? blkdev_ioctl+0x8d/0x2a0
block_ioctl+0x3f/0x50
__x64_sys_ioctl+0x80/0xb0
do_syscall_64+0x38/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6d37ccdd2 ]
capsnaps will take inode references via ihold when queueing to flush.
When force unmounting, the client will just close the sessions and
may never get a flush reply, causing a leak and inode ref leak.
Fix this by removing the capsnaps for an inode when removing the caps.
URL: https://tracker.ceph.com/issues/52295
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b11ed50346 ]
The current code will update the mtime and then try to get caps to
handle the write. If we end up having to request caps from the MDS, then
the mtime in the cap grant will clobber the updated mtime and it'll be
lost.
This is most noticable when two clients are alternately writing to the
same file. Fw caps are continually being granted and revoked, and the
mtime ends up stuck because the updated mtimes are always being
overwritten with the old one.
Fix this by changing the order of operations in ceph_write_iter to get
the caps before updating the times. Also, make sure we check the pool
full conditions before even getting any caps or uninlining.
URL: https://tracker.ceph.com/issues/46574
Reported-by: Jozef Kováč <kovac@firma.zoznam.sk>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Luis Henriques <lhenriques@suse.de>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aac6c0f907 ]
The xilinx dma driver uses the consistent allocations, so for correct
operation also set the DMA mask for coherent APIs. It fixes the below
kernel crash with dmatest client when DMA IP is configured with 64-bit
address width and linux is booted from high (>4GB) memory.
Call trace:
[ 489.531257] dma_alloc_from_pool+0x8c/0x1c0
[ 489.535431] dma_direct_alloc+0x284/0x330
[ 489.539432] dma_alloc_attrs+0x80/0xf0
[ 489.543174] dma_pool_alloc+0x160/0x2c0
[ 489.547003] xilinx_cdma_prep_memcpy+0xa4/0x180
[ 489.551524] dmatest_func+0x3cc/0x114c
[ 489.555266] kthread+0x124/0x130
[ 489.558486] ret_from_fork+0x10/0x3c
[ 489.562051] ---[ end trace 248625b2d596a90a ]---
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Reviewed-by: Harini Katakam <harini.katakam@xilinx.com>
Link: https://lore.kernel.org/r/1629363528-30347-1-git-send-email-radhey.shyam.pandey@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3811a50ad ]
Currently, iommu_init_ga() checks and disables IOMMU VAPIC support
(i.e. AMD AVIC support in IOMMU) when GAMSup feature bit is not set.
However it forgets to clear IRQ_POSTING_CAP from the previously set
amd_iommu_irq_ops.capability.
This triggers an invalid page fault bug during guest VM warm reboot
if AVIC is enabled since the irq_remapping_cap(IRQ_POSTING_CAP) is
incorrectly set, and crash the system with the following kernel trace.
BUG: unable to handle page fault for address: 0000000000400dd8
RIP: 0010:amd_iommu_deactivate_guest_mode+0x19/0xbc
Call Trace:
svm_set_pi_irte_mode+0x8a/0xc0 [kvm_amd]
? kvm_make_all_cpus_request_except+0x50/0x70 [kvm]
kvm_request_apicv_update+0x10c/0x150 [kvm]
svm_toggle_avic_for_irq_window+0x52/0x90 [kvm_amd]
svm_enable_irq_window+0x26/0xa0 [kvm_amd]
vcpu_enter_guest+0xbbe/0x1560 [kvm]
? avic_vcpu_load+0xd5/0x120 [kvm_amd]
? kvm_arch_vcpu_load+0x76/0x240 [kvm]
? svm_get_segment_base+0xa/0x10 [kvm_amd]
kvm_arch_vcpu_ioctl_run+0x103/0x590 [kvm]
kvm_vcpu_ioctl+0x22a/0x5d0 [kvm]
__x64_sys_ioctl+0x84/0xc0
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xae
Fixes by moving the initializing of AMD IOMMU interrupt remapping mode
(amd_iommu_guest_ir) earlier before setting up the
amd_iommu_irq_ops.capability with appropriate IRQ_POSTING_CAP flag.
[joro: Squashed the two patches and limited
check_features_on_all_iommus() to CONFIG_IRQ_REMAP
to fix a compile warning.]
Signed-off-by: Wei Huang <wei.huang2@amd.com>
Co-developed-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Link: https://lore.kernel.org/r/20210820202957.187572-2-suravee.suthikulpanit@amd.com
Link: https://lore.kernel.org/r/20210820202957.187572-3-suravee.suthikulpanit@amd.com
Fixes: 8bda0cfbdc ("iommu/amd: Detect and initialize guest vAPIC log")
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 907872baa9 ]
parisc build test images fail to compile with the following error.
drivers/parisc/dino.c:160:12: error:
'pci_dev_is_behind_card_dino' defined but not used
Move the function just ahead of its only caller to avoid the error.
Fixes: 5fa1659105 ("parisc: Disable HP HSC-PCI Cards to prevent kernel crash")
Cc: Helge Deller <deller@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b92d4add5 ]
DEFINE_SMP_CALL_CACHE_FUNCTION() was usefel before the CPU hotplug rework
to ensure that the cache related functions are called on the upcoming CPU
because the notifier itself could run on any online CPU.
The hotplug state machine guarantees that the callbacks are invoked on the
upcoming CPU. So there is no need to have this SMP function call
obfuscation. That indirection was missed when the hotplug notifiers were
converted.
This also solves the problem of ARM64 init_cache_level() invoking ACPI
functions which take a semaphore in that context. That's invalid as SMP
function calls run with interrupts disabled. Running it just from the
callback in context of the CPU hotplug thread solves this.
Fixes: 8571890e15 ("arm64: Add support for ACPI based firmware tables")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Will Deacon <will@kernel.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/871r69ersb.ffs@tglx
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3dc549986 ]
Due to high latency in PCIE clock switching on RKL platforms,
switching the PCIE clock dynamically at runtime can lead to HDMI/DP
audio problems. On newer asics this is handled in the SMU firmware.
For SMU7-based asics, disable PCIE clock switching to avoid the issue.
AMD provide a parameter to disable PICE_DPM.
modprobe amdgpu ppfeaturemask=0xfff7bffb
It's better to contorl PCIE_DPM in amd gpu driver,
switch PCI_DPM by determining intel RKL platform for SMU7-based asics.
Fixes: 1a31474cdb ("drm/amd/pm: workaround for audio noise issue")
Ref: https://lists.freedesktop.org/archives/amd-gfx/2021-August/067413.html
Signed-off-by: Koba Ko <koba.ko@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb83610762 ]
There are two pairs of declarations for thermal_cooling_device_register()
and thermal_of_cooling_device_register(), and only one set was changed
in a recent patch, so the other one now causes a compile-time warning:
drivers/net/wireless/mediatek/mt76/mt7915/init.c: In function 'mt7915_thermal_init':
drivers/net/wireless/mediatek/mt76/mt7915/init.c:134:48: error: passing argument 1 of 'thermal_cooling_device_register' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
134 | cdev = thermal_cooling_device_register(wiphy_name(wiphy), phy,
| ^~~~~~~~~~~~~~~~~
In file included from drivers/net/wireless/mediatek/mt76/mt7915/init.c:7:
include/linux/thermal.h:407:39: note: expected 'char *' but argument is of type 'const char *'
407 | thermal_cooling_device_register(char *type, void *devdata,
| ~~~~~~^~~~
Change the dummy helper functions to have the same arguments as the
normal version.
Fixes: f991de53a8 ("thermal: make device_register's type argument const")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210722090717.1116748-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4002173b7 ]
The first thing metric_delayed_work does is check mdsc->stopping,
and then return immediately if it's set. That's good since we would
have already torn down the metric structures at this point, otherwise,
but there is no locking around mdsc->stopping.
It's possible that the ceph_metric_destroy call could race with the
delayed_work, in which case we could end up with the delayed_work
accessing destroyed percpu variables.
At this point in the mdsc teardown, the "stopping" flag has already been
set, so there's no benefit to flushing the work. Move the work
cancellation in ceph_metric_destroy ahead of the percpu variable
destruction, and eliminate the flush_delayed_work call in
ceph_mdsc_destroy.
Fixes: 18f473b384 ("ceph: periodically send perf metrics to MDSes")
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Xiubo Li <xiubli@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d453ceb654 ]
Add trace event to report samples and their timestamp coming from the
EC. It allows to check if the timestamps are correct and the filter is
working correctly without introducing too much latency.
To enable these events:
cd /sys/kernel/debug/tracing/
echo 1 > events/cros_ec/enable
echo 0 > events/cros_ec/cros_ec_request_start/enable
echo 0 > events/cros_ec/cros_ec_request_done/enable
echo 1 > tracing_on
cat trace_pipe
Observe event flowing:
irq/105-chromeo-95 [000] .... 613.659758: cros_ec_sensorhub_timestamp: ...
irq/105-chromeo-95 [000] .... 613.665219: cros_ec_sensorhub_filter: dx: ...
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 020162d6f4 upstream.
This fixes a race condition: After pwmchip_add() is called there might
already be a consumer and then modifying the hardware behind the
consumer's back is bad. So reset before calling pwmchip_add().
Note that reseting the hardware isn't the right thing to do if the PWM
is already running as it might e.g. disable (or even enable) a backlight
that is supposed to be on (or off).
Fixes: 4dce82c1e8 ("pwm: add pwm-mxs support")
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d2813fb17 upstream.
This fixes a race condition: After pwmchip_add() is called there might
already be a consumer and then modifying the hardware behind the
consumer's back is bad. So set the default before.
(Side-note: I don't know what this register setting actually does, if
this modifies the polarity there is an inconsistency because the
inversed polarity isn't considered if the PWM is already running during
.probe().)
Fixes: acfd92fdfb ("pwm: lpc32xx: Set PWM_PIN_LEVEL bit to default value")
Cc: Sylvain Lemieux <slemieux@tycoint.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a9344cd0a upstream.
There are variables(power.may_skip_resume and dev->power.must_resume)
and DPM_FLAG_MAY_SKIP_RESUME flags to control the resume of devices after
a system wide suspend transition.
Setting the DPM_FLAG_MAY_SKIP_RESUME flag means that the driver allows
its "noirq" and "early" resume callbacks to be skipped if the device
can be left in suspend after a system-wide transition into the working
state. PM core determines that the driver's "noirq" and "early" resume
callbacks should be skipped or not with dev_pm_skip_resume() function by
checking power.may_skip_resume variable.
power.must_resume variable is getting set to false in __device_suspend()
function without checking device's DPM_FLAG_MAY_SKIP_RESUME settings.
In problematic scenario, where all the devices in the suspend_late
stage are successful and some device can fail to suspend in
suspend_noirq phase. So some devices successfully suspended in suspend_late
stage are not getting chance to execute __device_suspend_noirq()
to set dev->power.must_resume variable to true and not getting
resumed in early_resume phase.
Add a check for device's DPM_FLAG_MAY_SKIP_RESUME flag before
setting power.must_resume variable in __device_suspend function.
Fixes: 6e176bf8d4 ("PM: sleep: core: Do not skip callbacks in the resume phase")
Signed-off-by: Prasad Sodagudi <psodagud@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98e2e409e7 upstream.
When the refcount is decreased to 0, the resource reclamation branch is
entered. Before CPU0 reaches the race point (1), CPU1 may obtain the
spinlock and traverse the rbtree to find 'root', see
nilfs_lookup_root().
Although CPU1 will call refcount_inc() to increase the refcount, it is
obviously too late. CPU0 will release 'root' directly, CPU1 then
accesses 'root' and triggers UAF.
Use refcount_dec_and_lock() to ensure that both the operations of
decrease refcount to 0 and link deletion are lock protected eliminates
this risk.
CPU0 CPU1
nilfs_put_root():
<-------- (1)
spin_lock(&nilfs->ns_cptree_lock);
rb_erase(&root->rb_node, &nilfs->ns_cptree);
spin_unlock(&nilfs->ns_cptree_lock);
kfree(root);
<-------- use-after-free
refcount_t: underflow; use-after-free.
WARNING: CPU: 2 PID: 9476 at lib/refcount.c:28 \
refcount_warn_saturate+0x1cf/0x210 lib/refcount.c:28
Modules linked in:
CPU: 2 PID: 9476 Comm: syz-executor.0 Not tainted 5.10.45-rc1+ #3
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), ...
RIP: 0010:refcount_warn_saturate+0x1cf/0x210 lib/refcount.c:28
... ...
Call Trace:
__refcount_sub_and_test include/linux/refcount.h:283 [inline]
__refcount_dec_and_test include/linux/refcount.h:315 [inline]
refcount_dec_and_test include/linux/refcount.h:333 [inline]
nilfs_put_root+0xc1/0xd0 fs/nilfs2/the_nilfs.c:795
nilfs_segctor_destroy fs/nilfs2/segment.c:2749 [inline]
nilfs_detach_log_writer+0x3fa/0x570 fs/nilfs2/segment.c:2812
nilfs_put_super+0x2f/0xf0 fs/nilfs2/super.c:467
generic_shutdown_super+0xcd/0x1f0 fs/super.c:464
kill_block_super+0x4a/0x90 fs/super.c:1446
deactivate_locked_super+0x6a/0xb0 fs/super.c:335
deactivate_super+0x85/0x90 fs/super.c:366
cleanup_mnt+0x277/0x2e0 fs/namespace.c:1118
__cleanup_mnt+0x15/0x20 fs/namespace.c:1125
task_work_run+0x8e/0x110 kernel/task_work.c:151
tracehook_notify_resume include/linux/tracehook.h:188 [inline]
exit_to_user_mode_loop kernel/entry/common.c:164 [inline]
exit_to_user_mode_prepare+0x13c/0x170 kernel/entry/common.c:191
syscall_exit_to_user_mode+0x16/0x30 kernel/entry/common.c:266
do_syscall_64+0x45/0x80 arch/x86/entry/common.c:56
entry_SYSCALL_64_after_hwframe+0x44/0xa9
There is no reproduction program, and the above is only theoretical
analysis.
Link: https://lkml.kernel.org/r/1629859428-5906-1-git-send-email-konishi.ryusuke@gmail.com
Fixes: ba65ae4729 ("nilfs2: add checkpoint tree to nilfs object")
Link: https://lkml.kernel.org/r/20210723012317.4146-1-thunder.leizhen@huawei.com
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e1fbbd0731 upstream.
Keno Fischer reported that when a binray loaded via ld-linux-x the
prctl(PR_SET_MM_MAP) doesn't allow to setup brk value because it lays
before mm:end_data.
For example a test program shows
| # ~/t
|
| start_code 401000
| end_code 401a15
| start_stack 7ffce4577dd0
| start_data 403e10
| end_data 40408c
| start_brk b5b000
| sbrk(0) b5b000
and when executed via ld-linux
| # /lib64/ld-linux-x86-64.so.2 ~/t
|
| start_code 7fc25b0a4000
| end_code 7fc25b0c4524
| start_stack 7fffcc6b2400
| start_data 7fc25b0ce4c0
| end_data 7fc25b0cff98
| start_brk 55555710c000
| sbrk(0) 55555710c000
This of course prevent criu from restoring such programs. Looking into
how kernel operates with brk/start_brk inside brk() syscall I don't see
any problem if we allow to setup brk/start_brk without checking for
end_data. Even if someone pass some weird address here on a purpose then
the worst possible result will be an unexpected unmapping of existing vma
(own vma, since prctl works with the callers memory) but test for
RLIMIT_DATA is still valid and a user won't be able to gain more memory in
case of expanding VMAs via new values shipped with prctl call.
Link: https://lkml.kernel.org/r/20210121221207.GB2174@grain
Fixes: bbdc6076d2 ("binfmt_elf: move brk out of mmap when doing direct loader exec")
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Reported-by: Keno Fischer <keno@juliacomputing.com>
Acked-by: Andrey Vagin <avagin@gmail.com>
Tested-by: Andrey Vagin <avagin@gmail.com>
Cc: Dmitry Safonov <0x7f454c46@gmail.com>
Cc: Kirill Tkhai <ktkhai@virtuozzo.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Cc: Alexander Mikhalitsyn <alexander.mikhalitsyn@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a86d41404 upstream.
Currently perf saves a build-id with size but old versions assumes the
size of 20. In case the build-id is less than 20 (like for MD5), it'd
fill the rest with 0s.
I saw a problem when old version of perf record saved a binary in the
build-id cache and new version of perf reads the data. The symbols
should be read from the build-id cache (as the path no longer has the
same binary) but it failed due to mismatch in the build-id.
symsrc__init: build id mismatch for /home/namhyung/.debug/.build-id/53/e4c2f42a4c61a2d632d92a72afa08f00000000/elf.
The build-id event in the data has 20 byte build-ids, but it saw a
different size (16) when it reads the build-id of the elf file in the
build-id cache.
$ readelf -n ~/.debug/.build-id/53/e4c2f42a4c61a2d632d92a72afa08f00000000/elf
Displaying notes found in: .note.gnu.build-id
Owner Data size Description
GNU 0x00000010 NT_GNU_BUILD_ID (unique build ID bitstring)
Build ID: 53e4c2f42a4c61a2d632d92a72afa08f
Let's fix this by allowing trailing zeros if the size is different.
Fixes: 39be8d0115 ("perf tools: Pass build_id object to dso__build_id_equal()")
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20210910224630.1084877-1-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 099ec97ac9 upstream.
clang warns:
drivers/staging/rtl8192u/r8192U_core.c:4268:20: warning: bitwise and of
boolean expressions; did you mean logical and? [-Wbool-operation-and]
bpacket_toself = bpacket_match_bssid &
^~~~~~~~~~~~~~~~~~~~~
&&
1 warning generated.
Replace the bitwise AND with a logical one to clear up the warning, as
that is clearly what was intended.
Fixes: 8fc8598e61 ("Staging: Added Realtek rtl8192u driver to staging")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20210814235625.1780033-1-nathan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef6c8d6ccf upstream.
When SCTP handles an INIT chunk, it calls for example:
sctp_sf_do_5_1B_init
sctp_verify_init
sctp_verify_param
sctp_process_init
sctp_process_param
handling of SCTP_PARAM_SET_PRIMARY
sctp_verify_init() wasn't doing proper size validation and neither the
later handling, allowing it to work over the chunk itself, possibly being
uninitialized memory.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6ffe7671b upstream.
In one of the fallbacks that SCTP has for identifying an association for an
incoming packet, it looks for AddIp chunk (from ASCONF) and take a peek.
Thing is, at this stage nothing was validating that the chunk actually had
enough content for that, allowing the peek to happen over uninitialized
memory.
Similar check already exists in actual asconf handling in
sctp_verify_asconf().
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fcf044891c upstream.
We do not need a SWIOTLB unless we have DRAM that is addressable beyond
the arm_dma_limit. Compare max_pfn with arm_dma_pfn_limit to determine
whether we do need a SWIOTLB to be initialized.
Fixes: ad3c7b18c5 ("arm: use swiotlb for bounce buffering on LPAE configs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8b92b8c1e upstream.
We should not walk/touch page tables outside of VMA boundaries when
holding only the mmap sem in read mode. Evil user space can modify the
VMA layout just before this function runs and e.g., trigger races with
page table removal code since commit dd2283f260 ("mm: mmap: zap pages
with read mmap_sem in munmap").
find_vma() does not check if the address is >= the VMA start address;
use vma_lookup() instead.
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Fixes: dd2283f260 ("mm: mmap: zap pages with read mmap_sem in munmap")
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a2b2eb556 upstream.
The Linux console's VT102 implementation already consumes OSC
("Operating System Command") sequences, probably because that's how
palette changes are transmitted.
In addition to OSC, there are three other major clases of ANSI control
strings: APC ("Application Program Command"), PM ("Privacy Message"),
and DCS ("Device Control String"). They are handled similarly to OSC in
terms of termination.
Source: vt100.net
Add three new enumerated states, one for each of these types. All three
are handled the same way right now--they simply consume input until
terminated. I hope to expand upon this firmament in the future. Add
new predicate ansi_control_string(), returning true for any of these
states. Replace explicit checks against ESosc with calls to this
function. Transition to these states appropriately from the escape
initiation (ESesc) state.
This was motivated by the following Notcurses bugs:
https://github.com/dankamongmen/notcurses/issues/2050https://github.com/dankamongmen/notcurses/issues/1828https://github.com/dankamongmen/notcurses/issues/2069
where standard VT sequences are not consumed by the Linux console. It's
not necessary that the Linux console *support* these sequences, but it
ought *consume* these well-specified classes of sequences.
Tested by sending a variety of escape sequences to the console, and
verifying that they still worked, or were now properly consumed.
Verified that the escapes were properly terminated at a generic level.
Verified that the Notcurses tools continued to show expected output on
the Linux console, except now without escape bleedthrough.
Link: https://lore.kernel.org/lkml/YSydL0q8iaUfkphg@schwarzgerat.orthanc/
Signed-off-by: nick black <dankamongmen@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ISP can do H & V flips whilst resizing or converting
the image, so expose that via V4L2_CID_[H|V]FLIP.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Currently the code was only setting some controls from
bcm2835_codec_set_ctrls, but it's simpler to use
v4l2_ctrl_handler_setup to avoid forgetting to adding new
controls to the list.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Completions don't reference count, so setting the completion
on the first buffer returned and then not reinitialising it
means that the flush function doesn't behave as intended.
Signal the completion when the last buffer is returned.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Should we go through the timeout failure case with port_disable
not returning all buffers for whatever reason, the
buffers_with_vpu counter gets left at a non-zero value, which
will cause reference counting issues should the instance be
reused.
Reset the count when the port is enabled again, but before
any buffers have been sent to the VPU.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
When a buffer is returned on a port that is disabled, return it
to the videobuf2 QUEUED state instead of DONE which returns it
to the client.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The firmware defaults to not stopping video decode if only the
pixel aspect ratio or colourspace change. V4L2 requires us
to stop decoding on any change, therefore tell the firmware
of the desire for this alternate behaviour.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
When a format changed event occurs, the spec says that it
triggers an implicit drain, and that needs to be signalled
via -EPIPE.
For BCM2835, the format changed event happens at the point
the format change occurs, so no further buffers exist from
before the resolution changed point. We therefore signal the
last buffer immediately.
We don't have a V4L2 available to us at this point, so set
the videobuf2 queue last_buffer_dequeued flag directly.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The list of includes was slightly over generic, and wasn't
in alphabetical order. Clean it up.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
With video decode we now enable both input and output ports on
the component. This means that buffers will get passed to the VPU
earlier than desired if they are queued befoer STREAMON.
Check that the queue is streaming before sending buffers to the VPU.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The V4L2 stateful video decoder API requires that you can STREAMON
on only the OUTPUT queue, feed in buffers, and wait for the
SOURCE_CHANGE event.
This requires that we enable the MMAL output port at the same time
as the input port, because the output port is the one that creates
the SOURCE_CHANGED event.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Before uniniting the decode context sync with the IRQ queues to ensure
that decode no longer has any buffers in use. This fixes a problem that
manifested as ffmpeg leaking CMA buffers when it did a stream off on
OUTPUT before CAPTURE, though in reality it was probably much more
dangerous than that.
Signed-off-by: John Cox <jc@kynesim.co.uk>
Remove unused ctx state tracking variable and associated defines.
Their presence implies they might be used, but they aren't.
Signed-off-by: John Cox <jc@kynesim.co.uk>
With EDPWRDOWN set in idle, it must be cleared before checking for
ENERGYON going high, indicating that a link is being established.
The existing code allows 640ms for ENERGYON to go high, but on
Raspberry Pis that appears not to be enough, causing link detection
to fail.
Increase the polling timeout to 1500ms - with a polling interval of
10ms it shouldn't cause unnecessary delays.
See: https://github.com/raspberrypi/linux/issues/4393
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
V4L2 spec says that G/S/TRY_FMT IOCTLs should never return errors for
anything other than wrong buffer types. Improve the capture format
function such that this is so and unsupported values get converted
to supported ones properly.
Signed-off-by: John Cox <jc@kynesim.co.uk>
commit 02319bf15a upstream.
After d12e1c4649 ("net: dsa: b53: Set correct number of ports in the
DSA struct") we stopped setting dsa_switch::num_ports to DSA_MAX_PORTS,
which created an off by one error between the statically allocated
bcm_sf2_priv::port_sts array (of size DSA_MAX_PORTS). When
dsa_is_cpu_port() is used, we end-up accessing an out of bounds member
and causing a NPD.
Fix this by iterating with the appropriate port count using
ds->num_ports.
Fixes: d12e1c4649 ("net: dsa: b53: Set correct number of ports in the DSA struct")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eca4cf12ac upstream.
The recent patch has introduced a regression by not reading the reset
count in the ERROR_RECOVERY async event handler. We may have just
gone through a reset and the reset count has just incremented. If
we don't update the reset count in the ERROR_RECOVERY event handler,
the health check timer will see that the reset count has changed and
will initiate an unintended reset.
Restore the unconditional update of the reset count in
bnxt_async_event_process() if error recovery watchdog is enabled.
Also, update the reset count at the end of the reset sequence to
make it even more robust.
Fixes: 1b2b918319 ("bnxt_en: Fix possible unintended driver initiated error recovery")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81065b35e2 upstream.
There are two cases for machine check recovery:
1) The machine check was triggered by ring3 (application) code.
This is the simpler case. The machine check handler simply queues
work to be executed on return to user. That code unmaps the page
from all users and arranges to send a SIGBUS to the task that
triggered the poison.
2) The machine check was triggered in kernel code that is covered by
an exception table entry. In this case the machine check handler
still queues a work entry to unmap the page, etc. but this will
not be called right away because the #MC handler returns to the
fix up code address in the exception table entry.
Problems occur if the kernel triggers another machine check before the
return to user processes the first queued work item.
Specifically, the work is queued using the ->mce_kill_me callback
structure in the task struct for the current thread. Attempting to queue
a second work item using this same callback results in a loop in the
linked list of work functions to call. So when the kernel does return to
user, it enters an infinite loop processing the same entry for ever.
There are some legitimate scenarios where the kernel may take a second
machine check before returning to the user.
1) Some code (e.g. futex) first tries a get_user() with page faults
disabled. If this fails, the code retries with page faults enabled
expecting that this will resolve the page fault.
2) Copy from user code retries a copy in byte-at-time mode to check
whether any additional bytes can be copied.
On the other side of the fence are some bad drivers that do not check
the return value from individual get_user() calls and may access
multiple user addresses without noticing that some/all calls have
failed.
Fix by adding a counter (current->mce_count) to keep track of repeated
machine checks before task_work() is called. First machine check saves
the address information and calls task_work_add(). Subsequent machine
checks before that task_work call back is executed check that the address
is in the same page as the first machine check (since the callback will
offline exactly one page).
Expected worst case is four machine checks before moving on (e.g. one
user access with page faults disabled, then a repeat to the same address
with page faults enabled ... repeat in copy tail bytes). Just in case
there is some code that loops forever enforce a limit of 10.
[ bp: Massage commit message, drop noinstr, fix typo, extend panic
messages. ]
Fixes: 5567d11c21 ("x86/mce: Send #MC singal from task work")
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/YT/IJ9ziLqmtqEPu@agluck-desk2.amr.corp.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0341d5e3d1 ]
The cur_tx counter must be incremented after TACT bit of
txdesc->status was set. However, a CPU is possible to reorder
instructions and/or memory accesses between cur_tx and
txdesc->status. And then, if TX interrupt happened at such a
timing, the sh_eth_tx_free() may free the descriptor wrongly.
So, add wmb() before cur_tx++.
Otherwise NETDEV WATCHDOG timeout is possible to happen.
Fixes: 86a74ff21a ("net: sh_eth: add support for Renesas SuperH Ethernet")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdff1eda69 ]
One MIPS platform (mach-rc32434) defines GPIOBASE. This macro
conflicts with one of the same name in lpc_sch.c. Rename the latter one
to prevent the build error.
../drivers/mfd/lpc_sch.c:25: error: "GPIOBASE" redefined [-Werror]
25 | #define GPIOBASE 0x44
../arch/mips/include/asm/mach-rc32434/rb.h:32: note: this is the location of the previous definition
32 | #define GPIOBASE 0x050000
Cc: Denis Turischev <denis@compulab.co.il>
Fixes: e82c60ae7d ("mfd: Introduce lpc_sch for Intel SCH LPC bridge")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 922e8ce883 ]
The IRQ support for SCH GPIO is not specific to the Intel Quark SoC.
Moreover the IRQ routing is quite interesting there, so while it's
needs a special support, the driver haven't it anyway yet.
Due to above remove basically redundant code of IRQ support.
This reverts commit ec689a8a81.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b2b918319 ]
If error recovery is already enabled, bnxt_timer() will periodically
check the heartbeat register and the reset counter. If we get an
error recovery async. notification from the firmware (e.g. change in
primary/secondary role), we will immediately read and update the
heartbeat register and the reset counter. If the timer for the next
health check expires soon after this, we may read the heartbeat register
again in quick succession and find that it hasn't changed. This will
trigger error recovery unintentionally.
The likelihood is small because we also reset fw_health->tmr_counter
which will reset the interval for the next health check. But the
update is not protected and bnxt_timer() can miss the update and
perform the health check without waiting for the full interval.
Fix it by only reading the heartbeat register and reset counter in
bnxt_async_event_process() if error recovery is trasitioning to the
enabled state. Also add proper memory barriers so that when enabling
for the first time, bnxt_timer() will see the tmr_counter interval and
perform the health check after the full interval has elapsed.
Fixes: 7e914027f7 ("bnxt_en: Enable health monitoring.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4d95c3c19 ]
We currently only log the error recovery settings if it is enabled.
In some cases, firmware disables error recovery after it was
initially enabled. Without logging anything, the user will not be
aware of this change in setting.
Log it when error recovery is disabled. Also, change the reset count
value from hexadecimal to decimal.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a44daa8fcb ]
Firmware is capable of generating asynchronous debug notifications.
The event data is opaque to the driver and is simply logged. Debug
notifications can be enabled by turning on hardware status messages
using the ethtool msglvl interface.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6fdab8a3ad ]
The current asic.rev is incomplete and does not include the metal
revision. Add the metal revision and decode the complete asic
revision into the more common and readable form (A0, B0, etc).
Fixes: 7154917a12 ("bnxt_en: Refactor bnxt_dl_info_get().")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63f8428b40 ]
Broadcom's b53 switches have one IMP (Inband Management Port) that needs
to be programmed using its own designed register. IMP port may be
different than CPU port - especially on devices with multiple CPU ports.
For that reason it's required to explicitly note IMP port index and
check for it when choosing a register to use.
This commit fixes BCM5301x support. Those switches use CPU port 5 while
their IMP port is 8. Before this patch b53 was trying to program port 5
with B53_PORT_OVERRIDE_CTRL instead of B53_GMII_PORT_OVERRIDE_CTRL(5).
It may be possible to also replace "cpu_port" usages with
dsa_is_cpu_port() but that is out of the scope of thix BCM5301x fix.
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a0ed250f9 ]
The GRE tunnel device can pull existing outer headers in ipge_xmit.
This is a rare path, apparently unique to this device. The below
commit ensured that pulling does not move skb->data beyond csum_start.
But it has a false positive if ip_summed is not CHECKSUM_PARTIAL and
thus csum_start is irrelevant.
Refine to exclude this. At the same time simplify and strengthen the
test.
Simplify, by moving the check next to the offending pull, making it
more self documenting and removing an unnecessary branch from other
code paths.
Strengthen, by also ensuring that the transport header is correct and
therefore the inner headers will be after skb_reset_inner_headers.
The transport header is set to csum_start in skb_partial_csum_set.
Link: https://lore.kernel.org/netdev/YS+h%2FtqCJJiQei+W@shredder/
Fixes: 1d011c4803 ("ip_gre: add validation for csum_start")
Reported-by: Ido Schimmel <idosch@idosch.org>
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ddbc2a00d ]
Previous commit 68233c583a removes the qlcnic_rom_lock()
in qlcnic_pinit_from_rom(), but remains its corresponding
unlock function, which is odd. I'm not very sure whether the
lock is missing, or the unlock is redundant. This bug is
suggested by a static analysis tool, please advise.
Fixes: 68233c583a ("qlcnic: updated reset sequence")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7c5e6ff53 ]
syzbot found that forcing a big quantum attribute would crash hosts fast,
essentially using this:
tc qd replace dev eth0 root fq_codel quantum 4294967295
This is because fq_codel_dequeue() would have to loop
~2^31 times in :
if (flow->deficit <= 0) {
flow->deficit += q->quantum;
list_move_tail(&flow->flowchain, &q->old_flows);
goto begin;
}
SFQ max quantum is 2^19 (half a megabyte)
Lets adopt a max quantum of one megabyte for FQ_CODEL.
Fixes: 4b549a2ef4 ("fq_codel: Fair Queue Codel AQM")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 730affed24 ]
Bug reported by KASAN:
BUG: KASAN: use-after-scope in inet6_ehashfn (net/ipv6/inet6_hashtables.c:40)
Call Trace:
(...)
inet6_ehashfn (net/ipv6/inet6_hashtables.c:40)
(...)
nf_sk_lookup_slow_v6 (net/ipv6/netfilter/nf_socket_ipv6.c:91
net/ipv6/netfilter/nf_socket_ipv6.c:146)
It seems that this bug has already been fixed by Eric Dumazet in the
past in:
commit 78296c97ca ("netfilter: xt_socket: fix a stack corruption bug")
But a variant of the same issue has been introduced in
commit d64d80a2cd ("netfilter: x_tables: don't extract flow keys on early demuxed sks in socket match")
`daddr` and `saddr` potentially hold a reference to ipv6_var that is no
longer in scope when the call to `nf_socket_get_sock_v6` is made.
Fixes: d64d80a2cd ("netfilter: x_tables: don't extract flow keys on early demuxed sks in socket match")
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Benjamin Hesmans <benjamin.hesmans@tessares.net>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d12e1c4649 ]
Setting DSA_MAX_PORTS caused DSA to call b53 callbacks (e.g.
b53_disable_port() during dsa_register_switch()) for invalid
(non-existent) ports. That made b53 modify unrelated registers and is
one of reasons for a broken BCM5301x support.
This problem exists for years but DSA_MAX_PORTS usage has changed few
times. It seems the most accurate to reference commit dropping
dsa_switch_alloc() in the Fixes tag.
Fixes: 7e99e34701 ("net: dsa: remove dsa_switch_alloc helper")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdb067d31c ]
It isn't true that CPU port is always the last one. Switches BCM5301x
have 9 ports (port 6 being inactive) and they use port 5 as CPU by
default (depending on design some other may be CPU ports too).
A more reliable way of determining number of ports is to check for the
last set bit in the "enabled_ports" bitfield.
This fixes b53 internal state, it will allow providing accurate info to
the DSA and is required to fix BCM5301x support.
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ecdc28defc ]
If the network devices connected to the system beyond
HSO_MAX_NET_DEVICES. add_net_device() in hso_create_net_device()
will be failed for the network_table is full. It will lead to
business failure which rely on network_table, for example,
hso_suspend() and hso_resume(). It will also lead to memory leak
because resource release process can not search the hso_device
object from network_table in hso_free_interface().
Add failure handler for add_net_device() in hso_create_net_device()
to solve the above problems.
Fixes: 72dc1c096c ("HSO: add option hso driver")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfd862a7e9 ]
'$cin' and '$sin' variables are local to a function: they are then not
available from the cleanup trap.
Instead, we need to use '$large' and '$small' that are not local and
defined just before setting the trap.
Without this patch, running this script in a loop might cause a:
write: No space left on device
issue.
Fixes: 1a418cb8e8 ("mptcp: simult flow self-tests")
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e90dfa7a8 ]
I noticed that only port 0 worked on the RTL8366RB since we
started to use custom tags.
It turns out that the format of egress custom tags is actually
different from ingress custom tags. While the lower bits just
contain the port number in ingress tags, egress tags need to
indicate destination port by setting the bit for the
corresponding port.
It was working on port 0 because port 0 added 0x00 as port
number in the lower bits, and if you do this the packet appears
at all ports, including the intended port. Ooops.
Fix this and all ports work again. Use the define for shifting
the "type A" into place while we're at it.
Tested on the D-Link DIR-685 by sending traffic to each of
the ports in turn. It works.
Fixes: 86dd9868b8 ("net: dsa: tag_rtl4_a: Support also egress tags")
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 889a1b3f35 ]
If an error occurs after a 'gpiochip_add_data()' call it must be undone by
a corresponding 'gpiochip_remove()' as already done in the remove function.
To simplify the code a fix a leak in the error handling path of the probe,
use the managed version instead (i.e. 'devm_gpiochip_add_data()')
Fixes: 698b8eeaed ("gpio/mpc8xxx: change irq handler from chained to normal")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 555bda42b0 ]
Commit 698b8eeaed ("gpio/mpc8xxx: change irq handler from chained to normal")
has introduced a new 'goto err;' at the very end of the function, but has
not updated the error handling path accordingly.
Add the now missing 'irq_domain_remove()' call which balances a previous
'irq_domain_create_linear() call.
Fixes: 698b8eeaed ("gpio/mpc8xxx: change irq handler from chained to normal")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit edf7b4a2d8 ]
The build on fedora:35 and fedora:rawhide with clang is failing with:
49 41.00 fedora:35 : FAIL clang version 13.0.0 (Fedora 13.0.0~rc1-1.fc35)
bench/inject-buildid.c:351:6: error: variable 'len' set but not used [-Werror,-Wunused-but-set-variable]
u64 len = 0;
^
1 error generated.
make[3]: *** [/git/perf-5.14.0-rc7/tools/build/Makefile.build:139: bench] Error 2
50 41.11 fedora:rawhide : FAIL clang version 13.0.0 (Fedora 13.0.0~rc1-1.fc35)
bench/inject-buildid.c:351:6: error: variable 'len' set but not used [-Werror,-Wunused-but-set-variable]
u64 len = 0;
^
1 error generated.
make[3]: *** [/git/perf-5.14.0-rc7/tools/build/Makefile.build:139: bench] Error 2
That 'len' variable is not used at all, so just make sure all the
synthesize_RECORD() routines return ssize_t to propagate the writen()
return, as it may fail, ditch the 'ret' var and bail out if those
routines fail.
Fixes: 0bf02a0d80 ("perf bench: Add build-id injection benchmark")
Acked-by: Namhyung Kim <namhyung@kernel.org>
Link: http://lore.kernel.org/lkml/CAM9d7cgEZNSor+B+7Y2C+QYGme_v5aH0Zn0RLfxoQ+Fy83EHrg@mail.gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b5ff0405e ]
0day bot reports a build error:
ERROR: modpost: "clear_user_page" [drivers/media/v4l2-core/videobuf-dma-sg.ko] undefined!
so export it in arch/arc/ to fix the build error.
In most ARCHes, clear_user_page() is a macro. OTOH, in a few
ARCHes it is a function and needs to be exported.
PowerPC exported it in 2004. It looks like nds32 and nios2
still need to have it exported.
Fixes: 4102b53392 ("ARC: [mm] Aliasing VIPT dcache support 2/4")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-snps-arc@lists.infradead.org
Signed-off-by: Vineet Gupta <vgupta@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6826c6849b ]
The CPU_ON PSCI call takes a payload that KVM uses to configure a
destination vCPU to run. This payload is non-architectural state and not
exposed through any existing UAPI. Effectively, we have a race between
CPU_ON and userspace saving/restoring a guest: if the target vCPU isn't
ran again before the VMM saves its state, the requested PC and context
ID are lost. When restored, the target vCPU will be runnable and start
executing at its old PC.
We can avoid this race by making sure the reset payload is serviced
before userspace can access a vCPU's state.
Fixes: 358b28f09f ("arm/arm64: KVM: Allow a VCPU to fully reset itself")
Signed-off-by: Oliver Upton <oupton@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210818202133.1106786-3-oupton@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6654f9dfcb ]
KVM correctly serializes writes to a vCPU's reset state, however since
we do not take the KVM lock on the read side it is entirely possible to
read state from two different reset requests.
Cure the race for now by taking the KVM lock when reading the
reset_state structure.
Fixes: 358b28f09f ("arm/arm64: KVM: Allow a VCPU to fully reset itself")
Signed-off-by: Oliver Upton <oupton@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210818202133.1106786-2-oupton@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a89d69a44e ]
Since 2431c4f5b4 ("mtd: Implement mtd_{read,write}() as wrappers
around mtd_{read,write}_oob()") don't allow _write|_read and
_write_oob|_read_oob existing at the same time, we should check the
existence of callbacks "_read and _write" from subdev's master device
(We can trust master device since it has been registered) before
assigning, otherwise following warning occurs while making
concatenated device:
WARNING: CPU: 2 PID: 6728 at drivers/mtd/mtdcore.c:595
add_mtd_device+0x7f/0x7b0
Fixes: 2431c4f5b4 ("mtd: Implement mtd_{read,write}() around ...")
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210817114857.2784825-3-chengzhihao1@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a946506c48 ]
The driver was registering IRQ 0 when no IRQ was set. This leads to
warnings with newer kernels.
Clear the resource flags, so no resource is registered at all in this
case.
Fixes: 2f17dd34ff ("mfd: tqmx86: IO controller with I2C, Wachdog and GPIO")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3245a7b7b ]
Syzbot hit use-after-free in nf_tables_dump_sets. The problem was in
missing lock protection for nft_ct_pcpu_template_refcnt.
Before commit f102d66b33 ("netfilter: nf_tables: use dedicated
mutex to guard transactions") all transactions were serialized by global
mutex, but then global mutex was changed to local per netnamespace
commit_mutex.
This change causes use-after-free bug, when 2 netnamespaces concurently
changing nft_ct_pcpu_template_refcnt without proper locking. Fix it by
adding nft_ct_pcpu_mutex and protect all nft_ct_pcpu_template_refcnt
changes with it.
Fixes: f102d66b33 ("netfilter: nf_tables: use dedicated mutex to guard transactions")
Reported-and-tested-by: syzbot+649e339fa6658ee623d3@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit daa3736151 ]
Remove interrupt disablement during backlight setting. It is
way to dangerous and makes platforms instable by having it
miss vblank IRQs leading to the graphics derailing.
The code is using ndelay() which is not available on
platforms such as ARM and will result in 32 * udelay(1)
which is substantial.
Add some code to detect if an interrupt occurs during the
tight loop and in that case just redo it from the top.
Fixes: 5317f37e48 ("backlight: Add Kinetic KTD253 backlight driver")
Cc: Stephan Gerhold <stephan@gerhold.net>
Reported-by: newbyte@disroot.org
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f949a9ebce ]
On Cherry Trail devices with an AXP288 PMIC the external SD-card slot
used the AXP's DLDO2 as card-voltage and either DLDO3 or GPIO1LDO
(GPIO1 pin in low noise LDO mode) as signal-voltage.
These regulators are turned on/off and in case of the signal-voltage
also have their output-voltage changed by the _PS0 and _PS3 power-
management ACPI methods on the MMC-controllers ACPI fwnode as well as
by the _DSM ACPI method for changing the signal voltage.
The AML code implementing these methods is directly accessing the
PMIC through ACPI I2C OpRegion accesses, instead of using the special
PMIC OpRegion handled by drivers/acpi/pmic/intel_pmic_xpower.c .
This means that the contents of the involved PMIC registers can change
without the change being made through the regmap interface, so regmap
should not cache the contents of these registers.
Mark the regulator power on/off, the regulator voltage control and the
GPIO1 control registers as volatile, to avoid regmap caching them.
Specifically this fixes an issue on some models where the i915 driver
toggles another LDO using the same on/off register on/off through
MIPI sequences (through intel_soc_pmic_exec_mipi_pmic_seq_element())
which then writes back a cached on/off register-value where the
card-voltage is off causing the external sdcard slot to stop working
when the screen goes blank, or comes back on again.
The regulator register-range now marked volatile also includes the
buck regulator control registers. This is done on purpose these are
normally not touched by the AML code, but they are updated directly
by the SoC's PUNIT which means that they may also change without going
through regmap.
Note the AXP288 PMIC is only used on Bay- and Cherry-Trail platforms,
so even though this is an ACPI specific problem there is no need to
make the new volatile ranges conditional since these platforms always
use ACPI.
Fixes: dc91c3b6fe ("mfd: axp20x: Mark AXP20X_VBUS_IPSOUT_MGMT as volatile")
Fixes: cd53216625 ("mfd: axp20x: Fix axp288 volatile ranges")
Reported-and-tested-by: Clamshell <clamfly@163.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1511df6f5e upstream.
EMIT6_PCREL() macro assumes that the previous pass generated 6 bytes
of code, which is not the case if branch shortening took place. Fix by
using jit->prg, like all the other EMIT6_PCREL_*() macros.
Reported-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Fixes: 4e9b4a6883 ("s390/bpf: Use relative long branches")
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e61dc9da0 upstream.
The JIT uses agfi for subtracting constants, but -(-0x80000000) cannot
be represented as a 32-bit signed binary integer. Fix by using algfi in
this particular case.
Reported-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Fixes: 0546231057 ("s390/bpf: Add s390x eBPF JIT compiler backend")
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db7bee6538 upstream.
Currently the JIT completely removes things like `reg32 += 0`,
however, the BPF_ALU semantics requires the target register to be
zero-extended in such cases.
Fix by optimizing out only the arithmetic operation, but not the
subsequent zero-extension.
Reported-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Fixes: 0546231057 ("s390/bpf: Add s390x eBPF JIT compiler backend")
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0097ae5f7a ]
When the function IS_ALIGNED() returns false, the value of ret is 0.
So, we set ret to -EINVAL to indicate this error.
Clean up smatch warning:
drivers/ntb/test/ntb_perf.c:602 perf_setup_inbuf() warn: missing error
code 'ret'.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 319f83ac98 ]
When the value of nm->isr_ctx is false, the value of ret is 0.
So, we set ret to -ENOMEM to indicate this error.
Clean up smatch warning:
drivers/ntb/test/ntb_msi_test.c:373 ntb_msit_probe() warn: missing
error code 'ret'.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7db8263a12 ]
When adapter->registered_device_map is NULL, the value of err is
uncertain, we set err to -EINVAL to avoid ambiguity.
Clean up smatch warning:
drivers/net/ethernet/chelsio/cxgb/cxgb2.c:1114 init_one() warn: missing
error code 'err'
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d52c58b9c ]
The function bfq_setup_merge prepares the merging between two
bfq_queues, say bfqq and new_bfqq. To this goal, it assigns
bfqq->new_bfqq = new_bfqq. Then, each time some I/O for bfqq arrives,
the process that generated that I/O is disassociated from bfqq and
associated with new_bfqq (merging is actually a redirection). In this
respect, bfq_setup_merge increases new_bfqq->ref in advance, adding
the number of processes that are expected to be associated with
new_bfqq.
Unfortunately, the stable-merging mechanism interferes with this
setup. After bfqq->new_bfqq has been set by bfq_setup_merge, and
before all the expected processes have been associated with
bfqq->new_bfqq, bfqq may happen to be stably merged with a different
queue than the current bfqq->new_bfqq. In this case, bfqq->new_bfqq
gets changed. So, some of the processes that have been already
accounted for in the ref counter of the previous new_bfqq will not be
associated with that queue. This creates an unbalance, because those
references will never be decremented.
This commit fixes this issue by reestablishing the previous, natural
behaviour: once bfqq->new_bfqq has been set, it will not be changed
until all expected redirections have occurred.
Signed-off-by: Davide Zini <davidezini2@gmail.com>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Link: https://lore.kernel.org/r/20210802141352.74353-2-paolo.valente@linaro.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aabbdc67f3 ]
Add quirk CDC_MBIM_FLAG_AVOID_ALTSETTING_TOGGLE for Telit LN920
0x1061 composition in order to avoid bind error.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21274aa178 ]
Check one more time before exiting the API with an error.
Fix API to poll at least twice, in case there are other high priority
tasks and this API doesn't get CPU cycles for multiple jiffies update.
In addition, increase timeout from usecs_to_jiffies(10000) to
usecs_to_jiffies(20000), to prevent the case that for CONFIG_100HZ
timeout will be a single jiffies.
A single jiffies results actual timeout that can be any time between
1usec and 10msec. To solve this, a value of usecs_to_jiffies(20000)
ensures that timeout is 2 jiffies.
Signed-off-by: Smadar Fuks <smadarf@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dbe80cf471 ]
We must not pet a running watchdog when handle_boot_enabled is off
because this will kick off automatic triggering before userland is
running, defeating the purpose of the handle_boot_enabled control.
Furthermore, don't ping in case watchdog_set_last_hw_keepalive was
called incorrectly when the hardware watchdog is actually not running.
Fixed: cef9572e9a ("watchdog: add support for adjusting last known HW keepalive time")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/93d56386-6e37-060b-55ce-84de8cde535f@web.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 32837d8a8f ]
Some Cavium endpoints are implemented as multi-function devices without ACS
capability, but they actually don't support peer-to-peer transactions.
Add ACS quirks to declare DMA isolation for the following devices:
- BGX device found on Octeon-TX (8xxx)
- CGX device found on Octeon-TX2 (9xxx)
- RPM device found on Octeon-TX3 (10xxx)
Link: https://lore.kernel.org/r/20210810122425.1115156-1-george.cherian@marvell.com
Signed-off-by: George Cherian <george.cherian@marvell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1de58802f ]
J7200 has the same PCIe IP as in J721E with minor changes in the
wrapper. J7200 allows byte access of bridge configuration space
registers and the register field for LINK_DOWN interrupt is different.
J7200 also requires "quirk_detect_quiet_flag" to be set. Configure these
changes as part of driver data applicable only to J7200.
Link: https://lore.kernel.org/r/20210811123336.31357-4-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09c24094b2 ]
PCIe fails to link up if SERDES lanes not used by PCIe are assigned to
another protocol. For example, link training fails if lanes 2 and 3 are
assigned to another protocol while lanes 0 and 1 are used for PCIe to
form a two lane link. This failure is due to an incorrect tie-off on an
internal status signal indicating electrical idle.
Status signals going from SERDES to PCIe Controller are tied-off when a
lane is not assigned to PCIe. Signal indicating electrical idle is
incorrectly tied-off to a state that indicates non-idle. As a result,
PCIe sees unused lanes to be out of electrical idle and this causes
LTSSM to exit Detect.Quiet state without waiting for 12ms timeout to
occur. If a receiver is not detected on the first receiver detection
attempt in Detect.Active state, LTSSM goes back to Detect.Quiet and
again moves forward to Detect.Active state without waiting for 12ms as
required by PCIe base specification. Since wait time in Detect.Quiet is
skipped, multiple receiver detect operations are performed back-to-back
without allowing time for capacitance on the transmit lines to
discharge. This causes subsequent receiver detection to always fail even
if a receiver gets connected eventually.
Add a quirk flag "quirk_detect_quiet_flag" to program the minimum
time the LTSSM should wait on entering Detect.Quiet state here.
This has to be set for J7200 as it has an incorrect tie-off on unused
lanes.
Link: https://lore.kernel.org/r/20210811123336.31357-3-kishon@ti.com
Signed-off-by: Nadeem Athani <nadeem@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e242060c6 ]
Since kprobe_events and uprobe_events only check whether the
other same-type probe event has the same name or not, if the
user gives the same name of the existing tracepoint event (or
the other type of probe events), it silently fails to create
the tracefs entry (but registered.) as below.
/sys/kernel/tracing # ls events/task/task_rename
enable filter format hist id trigger
/sys/kernel/tracing # echo p:task/task_rename vfs_read >> kprobe_events
[ 113.048508] Could not create tracefs 'task_rename' directory
/sys/kernel/tracing # cat kprobe_events
p:task/task_rename vfs_read
To fix this issue, check whether the existing events have the
same name or not in trace_probe_register_event_call(). If exists,
it rejects to register the new event.
Link: https://lkml.kernel.org/r/162936876189.187130.17558311387542061930.stgit@devnote2
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ff80e2de3 ]
Although irq_create_mapping() is able to deal with duplicate
mappings, it really isn't supposed to be a substitute for
irq_find_mapping(), and can result in allocations that take place
in atomic context if the mapping didn't exist.
Fix the handful of MFD drivers that use irq_create_mapping() in
interrupt context by using irq_find_mapping() instead.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1e71c1688 ]
There is a potential race between fuse_read_interrupt() and
fuse_request_end().
TASK1
in fuse_read_interrupt(): delete req->intr_entry (while holding
fiq->lock)
TASK2
in fuse_request_end(): req->intr_entry is empty -> skip fiq->lock
wake up TASK3
TASK3
request is freed
TASK1
in fuse_read_interrupt(): dereference req->in.h.unique ***BAM***
Fix by always grabbing fiq->lock if the request was ever interrupted
(FR_INTERRUPTED set) thereby serializing with concurrent
fuse_read_interrupt() calls.
FR_INTERRUPTED is set before the request is queued on fiq->interrupts.
Dequeing the request is done with list_del_init() but FR_INTERRUPTED is not
cleared in this case.
Reported-by: lijiazi <lijiazi@xiaomi.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec343111c0 ]
These are the actual frequencies reported by the PLL, so let's
report these. The roundoffs are inappropriate, we should round
to the frequency that the clock will later report.
Drop some whitespace at the same time.
Cc: phone-devel@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 427900d27d upstream.
Currently, the VF does not clear the interrupt source immediately after
receiving the interrupt. As a result, if the second interrupt task is
triggered when processing the first interrupt task, clearing the
interrupt source before exiting will clear the interrupt sources of the
two tasks at the same time. As a result, no interrupt is triggered for
the second task. The VF detects the missed message only when the next
interrupt is generated.
Clearing it immediately after executing check_evt_cause ensures that:
1. Even if two interrupt tasks are triggered at the same time, they can
be processed.
2. If the second task is triggered during the processing of the first
task and the interrupt source is not cleared, the interrupt is reported
after vector0 is enabled.
Fixes: b90fcc5bd9 ("net: hns3: add reset handling for VF when doing Core/Global/IMP reset")
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b81d894874 upstream.
The firmware will not disable mac in flr process. Therefore, the driver
needs to proactively disable mac during flr, which is the same as the
function reset.
Fixes: 35d93a3004 ("net: hns3: adjust the process of PF reset")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1dc839ec09 upstream.
Currently, affinity_mask is set to a single cpu. As a result,
irqbalance becomes invalid in SUBSET or EXACT mode. To solve
this problem, change affinity_mask to numa node range. In this
way, irqbalance can be performed on the cpu of the numa node.
Fixes: 0812545487 ("net: hns3: add interrupt affinity support for misc interrupt")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d18e81183b upstream.
The hardware cannot handle short tunnel frames below 65 bytes,
and will cause vlan tag missing problem. So pads packet size to
65 bytes for tunnel frames to fix this bug.
Fixes: 3db084d28dc0("net: hns3: Fix for vxlan tx checksum bug")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1affc01fdc upstream.
The call to bnxt_free_mem(..., false) in the bnxt_half_open_nic() error
path will deallocate ring descriptor memory via bnxt_free_?x_rings(),
but because irq_re_init is false, the ring info itself is not freed.
To simplify error paths, deallocation functions have generally been
written to be safe when called on unallocated memory. It should always
be safe to call dev_close(), which calls bnxt_free_skbs() a second time,
even in this semi- allocated ring state.
Calling bnxt_free_skbs() a second time with the rings already freed will
cause NULL pointer dereference. Fix it by checking the rings are valid
before proceeding in bnxt_free_tx_skbs() and
bnxt_free_one_rx_ring_skbs().
Fixes: 975bc99a4a ("bnxt_en: Refactor bnxt_free_rx_skbs().")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 267cdfa213 upstream.
POWER9 DD2.2 and 2.3 hardware implements a "fake-suspend" mode where
certain TM instructions executed in HV=0 mode cause softpatch interrupts
so the hypervisor can emulate them and prevent problematic processor
conditions. In this fake-suspend mode, the treclaim. instruction does
not modify registers.
Unfortunately the rfscv instruction executed by the guest do not
generate softpatch interrupts, which can cause the hypervisor to lose
track of the fake-suspend mode, and it can execute this treclaim. while
not in fake-suspend mode. This modifies GPRs and crashes the hypervisor.
It's not trivial to disable scv in the guest with HFSCR now, because
they assume a POWER9 has scv available. So this fix saves and restores
checkpointed registers across the treclaim.
Fixes: 7854f7545b ("KVM: PPC: Book3S: Rework TM save/restore code and make it C-callable")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210908101718.118522-2-npiggin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 273c29e944 upstream.
If a failover occurs before a login response is received, the login
response buffer maybe undefined. Check that there was no failover
before accessing the login response buffer.
Fixes: 032c5e8284 ("Driver for IBM System i/p VNIC protocol")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e50e711351 upstream.
Turn udp_tunnel_nic work-queue to an ordered work-queue. This queue
holds the UDP-tunnel configuration commands of the different netdevs.
When the netdevs are functions of the same NIC the order of
execution may be crucial.
Problem example:
NIC with 2 PFs, both PFs declare offload quota of up to 3 UDP-ports.
$ifconfig eth2 1.1.1.1/16 up
$ip link add eth2_19503 type vxlan id 5049 remote 1.1.1.2 dev eth2 dstport 19053
$ip link set dev eth2_19503 up
$ip link add eth2_19504 type vxlan id 5049 remote 1.1.1.3 dev eth2 dstport 19054
$ip link set dev eth2_19504 up
$ip link add eth2_19505 type vxlan id 5049 remote 1.1.1.4 dev eth2 dstport 19055
$ip link set dev eth2_19505 up
$ip link add eth2_19506 type vxlan id 5049 remote 1.1.1.5 dev eth2 dstport 19056
$ip link set dev eth2_19506 up
NIC RX port offload infrastructure offloads the first 3 UDP-ports (on
all devices which sets NETIF_F_RX_UDP_TUNNEL_PORT feature) and not
UDP-port 19056. So both PFs gets this offload configuration.
$ip link set dev eth2_19504 down
This triggers udp-tunnel-core to remove the UDP-port 19504 from
offload-ports-list and offload UDP-port 19056 instead.
In this scenario it is important that the UDP-port of 19504 will be
removed from both PFs before trying to add UDP-port 19056. The NIC can
stop offloading a UDP-port only when all references are removed.
Otherwise the NIC may report exceeding of the offload quota.
Fixes: cc4e3835ef ("udp_tunnel: add central NIC RX port offload infrastructure")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 20e100f527 upstream.
Handle MFW (management FW) error response in order to avoid a crash
during recovery flows.
Changes from v1:
- Add "Fixes tag".
Fixes: tag 5e7ba042fd ("qed: Fix reading stale configuration information")
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b704b27be upstream.
If altname deletion of the short alternative name fails, the error
message printed is: "Failed to add short alternative name".
This is obviously a typo, as we are testing altname deletion.
Fix this using a proper error message.
Fixes: f95e6c9c46 ("selftest: net: add alternative names test")
Signed-off-by: Andrea Claudi <aclaudi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f884f3962 upstream.
Commit 10d3be5692 ("tcp-tso: do not split TSO packets at retransmit
time") may directly retrans a multiple segments TSO/GSO packet without
split, Since this commit, we can no longer assume that a retransmitted
packet is a single segment.
This patch fixes the tp->undo_retrans accounting in tcp_sacktag_one()
that use the actual segments(pcount) of the retransmitted packet.
Before that commit (10d3be5692), the assumption underlying the
tp->undo_retrans-- seems correct.
Fixes: 10d3be5692 ("tcp-tso: do not split TSO packets at retransmit time")
Signed-off-by: zhenggy <zhenggy@chinatelecom.cn>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a69ae291e1 upstream.
Commit 865c50e1d2 ("x86/uaccess: utilize CONFIG_CC_HAS_ASM_GOTO_OUTPUT")
added an optimised version of __get_user_asm() for x86 using 'asm goto'.
Like the non-optimised code, the 32-bit implementation of 64-bit
get_user() expands to a pair of 32-bit accesses. Unlike the
non-optimised code, the _original_ pointer is incremented to copy the
high word instead of loading through a new pointer explicitly
constructed to point at a 32-bit type. Consequently, if the pointer
points at a 64-bit type then we end up loading the wrong data for the
upper 32-bits.
This was observed as a mount() failure in Android targeting i686 after
b0cfcdd9b9 ("d_path: make 'prepend()' fill up the buffer exactly on
overflow") because the call to copy_from_kernel_nofault() from
prepend_copy() ends up in __get_kernel_nofault() and casts the source
pointer to a 'u64 __user *'. An attempt to mount at "/debug_ramdisk"
therefore ends up failing trying to mount "/debumdismdisk".
Use the existing '__gu_ptr' source pointer to unsigned int for 32-bit
__get_user_asm_u64() instead of the original pointer.
Cc: Bill Wendling <morbo@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 865c50e1d2 ("x86/uaccess: utilize CONFIG_CC_HAS_ASM_GOTO_OUTPUT")
Signed-off-by: Will Deacon <will@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6a52e73368 upstream.
DSA supports connecting to a phy-handle, and has a fallback to a non-OF
based method of connecting to an internal PHY on the switch's own MDIO
bus, if no phy-handle and no fixed-link nodes were present.
The -ENODEV error code from the first attempt (phylink_of_phy_connect)
is what triggers the second attempt (phylink_connect_phy).
However, when the first attempt returns a different error code than
-ENODEV, this results in an unbalance of calls to phylink_create and
phylink_destroy by the time we exit the function. The phylink instance
has leaked.
There are many other error codes that can be returned by
phylink_of_phy_connect. For example, phylink_validate returns -EINVAL.
So this is a practical issue too.
Fixes: aab9c4067d ("net: dsa: Plug in PHYLINK support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20210914134331.2303380-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04f08eb44b upstream.
syzbot reported another data-race in af_unix [1]
Lets change __skb_insert() to use WRITE_ONCE() when changing
skb head qlen.
Also, change unix_dgram_poll() to use lockless version
of unix_recvq_full()
It is verry possible we can switch all/most unix_recvq_full()
to the lockless version, this will be done in a future kernel version.
[1] HEAD commit: 8596e589b7
BUG: KCSAN: data-race in skb_queue_tail / unix_dgram_poll
write to 0xffff88814eeb24e0 of 4 bytes by task 25815 on cpu 0:
__skb_insert include/linux/skbuff.h:1938 [inline]
__skb_queue_before include/linux/skbuff.h:2043 [inline]
__skb_queue_tail include/linux/skbuff.h:2076 [inline]
skb_queue_tail+0x80/0xa0 net/core/skbuff.c:3264
unix_dgram_sendmsg+0xff2/0x1600 net/unix/af_unix.c:1850
sock_sendmsg_nosec net/socket.c:703 [inline]
sock_sendmsg net/socket.c:723 [inline]
____sys_sendmsg+0x360/0x4d0 net/socket.c:2392
___sys_sendmsg net/socket.c:2446 [inline]
__sys_sendmmsg+0x315/0x4b0 net/socket.c:2532
__do_sys_sendmmsg net/socket.c:2561 [inline]
__se_sys_sendmmsg net/socket.c:2558 [inline]
__x64_sys_sendmmsg+0x53/0x60 net/socket.c:2558
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffff88814eeb24e0 of 4 bytes by task 25834 on cpu 1:
skb_queue_len include/linux/skbuff.h:1869 [inline]
unix_recvq_full net/unix/af_unix.c:194 [inline]
unix_dgram_poll+0x2bc/0x3e0 net/unix/af_unix.c:2777
sock_poll+0x23e/0x260 net/socket.c:1288
vfs_poll include/linux/poll.h:90 [inline]
ep_item_poll fs/eventpoll.c:846 [inline]
ep_send_events fs/eventpoll.c:1683 [inline]
ep_poll fs/eventpoll.c:1798 [inline]
do_epoll_wait+0x6ad/0xf00 fs/eventpoll.c:2226
__do_sys_epoll_wait fs/eventpoll.c:2238 [inline]
__se_sys_epoll_wait fs/eventpoll.c:2233 [inline]
__x64_sys_epoll_wait+0xf6/0x120 fs/eventpoll.c:2233
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0x0000001b -> 0x00000001
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 25834 Comm: syz-executor.1 Tainted: G W 5.14.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 86b18aaa2b ("skbuff: fix a data race in skb_queue_len()")
Cc: Qian Cai <cai@lca.pw>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c4cea8fa7 upstream.
If the sendmsg() call in vhost_tx_batch() fails, both the 'batched_xdp'
and 'done_idx' indexes are left unchanged. If such failure happens
when batched_xdp == VHOST_NET_BATCH, the next call to
vhost_net_build_xdp() will access and write memory outside the xdp
buffers area.
Since sendmsg() can only error with EBADFD, this change addresses the
issue explicitly freeing the XDP buffers batch on error.
Fixes: 0a0be13b8f ("vhost_net: batch submitting XDP buffers to underlayer sockets")
Suggested-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec783c7cb2 upstream.
We need to import the 'sys' package since the script has called
sys.exit() method.
Fixes: 6ad7cbc015 ("Makefile: Add clang-tidy and static analyzer support to makefile")
Signed-off-by: Kortan <kortanzh@gmail.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5c102238c upstream.
There is an off-by-one problem in ipa_table_init_add(), when
initializing filter tables.
In that function, the number of filter table entries is determined
based on the number of set bits in the filter map. However that
count does *not* include the extra "slot" in the filter table that
holds the filter map itself. Meanwhile, ipa_table_addr() *does*
include the filter map in the memory it returns, but because the
count it's provided doesn't include it, it includes one too few
table entries.
Fix this by including the extra slot for the filter map in the count
computed in ipa_table_init_add().
Note: ipa_filter_reset_table() does not have this problem; it resets
filter table entries one by one, but does not overwrite the filter
bitmap.
Fixes: 2b9feef2b6 ("soc: qcom: ipa: filter and routing tables")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b89a05b21f upstream.
In perf_event_addr_filters_apply, the task associated with
the event (event->ctx->task) is read using READ_ONCE at the beginning
of the function, checked, and then re-read from event->ctx->task,
voiding all guarantees of the checks. Reuse the value that was read by
READ_ONCE to ensure the consistency of the task struct throughout the
function.
Fixes: 375637bc52 ("perf/core: Introduce address range filtering")
Signed-off-by: Baptiste Lepers <baptiste.lepers@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20210906015310.12802-1-baptiste.lepers@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70f437fb43 upstream.
Dispatching requests inline with the .queue_rq() call may block while
holding the send_mutex. If the tcp io_work also happens to schedule, it
may see the req_list is non-empty, leaving "pending" true and remaining
in TASK_RUNNING. Since io_work is of higher scheduling priority, the
.queue_rq task may not get a chance to run, blocking forward progress
and leading to io timeouts.
Instead of checking for pending requests within io_work, let the queueing
restart io_work outside the send_mutex lock if there is more work to be
done.
Fixes: a0fdd14180 ("nvme-tcp: rerun io_work if req_list is not empty")
Reported-by: Samuel Jones <sjones@kalrayinc.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee27e330a9 upstream.
Fixes the below flow of sleeping in atomic context by releasing
the RCU lock before calling to free_match_list.
build_match_list() <- disables preempt
-> free_match_list()
-> tree_put_node()
-> down_write_ref_node() <- take write lock
Fixes: 693c6883bb ("net/mlx5: Add hash table for flow groups in flow table")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 57f0ff059e upstream.
It's later supposed to be either a correct address or NULL. Without the
initialization, it may contain an undefined value which results in the
following segmentation fault:
# perf top --sort comm -g --ignore-callees=do_idle
terminates with:
#0 0x00007ffff56b7685 in __strlen_avx2 () from /lib64/libc.so.6
#1 0x00007ffff55e3802 in strdup () from /lib64/libc.so.6
#2 0x00005555558cb139 in hist_entry__init (callchain_size=<optimized out>, sample_self=true, template=0x7fffde7fb110, he=0x7fffd801c250) at util/hist.c:489
#3 hist_entry__new (template=template@entry=0x7fffde7fb110, sample_self=sample_self@entry=true) at util/hist.c:564
#4 0x00005555558cb4ba in hists__findnew_entry (hists=hists@entry=0x5555561d9e38, entry=entry@entry=0x7fffde7fb110, al=al@entry=0x7fffde7fb420,
sample_self=sample_self@entry=true) at util/hist.c:657
#5 0x00005555558cba1b in __hists__add_entry (hists=hists@entry=0x5555561d9e38, al=0x7fffde7fb420, sym_parent=<optimized out>, bi=bi@entry=0x0, mi=mi@entry=0x0,
sample=sample@entry=0x7fffde7fb4b0, sample_self=true, ops=0x0, block_info=0x0) at util/hist.c:288
#6 0x00005555558cbb70 in hists__add_entry (sample_self=true, sample=0x7fffde7fb4b0, mi=0x0, bi=0x0, sym_parent=<optimized out>, al=<optimized out>, hists=0x5555561d9e38)
at util/hist.c:1056
#7 iter_add_single_cumulative_entry (iter=0x7fffde7fb460, al=<optimized out>) at util/hist.c:1056
#8 0x00005555558cc8a4 in hist_entry_iter__add (iter=iter@entry=0x7fffde7fb460, al=al@entry=0x7fffde7fb420, max_stack_depth=<optimized out>, arg=arg@entry=0x7fffffff7db0)
at util/hist.c:1231
#9 0x00005555557cdc9a in perf_event__process_sample (machine=<optimized out>, sample=0x7fffde7fb4b0, evsel=<optimized out>, event=<optimized out>, tool=0x7fffffff7db0)
at builtin-top.c:842
#10 deliver_event (qe=<optimized out>, qevent=<optimized out>) at builtin-top.c:1202
#11 0x00005555558a9318 in do_flush (show_progress=false, oe=0x7fffffff80e0) at util/ordered-events.c:244
#12 __ordered_events__flush (oe=oe@entry=0x7fffffff80e0, how=how@entry=OE_FLUSH__TOP, timestamp=timestamp@entry=0) at util/ordered-events.c:323
#13 0x00005555558a9789 in __ordered_events__flush (timestamp=<optimized out>, how=<optimized out>, oe=<optimized out>) at util/ordered-events.c:339
#14 ordered_events__flush (how=OE_FLUSH__TOP, oe=0x7fffffff80e0) at util/ordered-events.c:341
#15 ordered_events__flush (oe=oe@entry=0x7fffffff80e0, how=how@entry=OE_FLUSH__TOP) at util/ordered-events.c:339
#16 0x00005555557cd631 in process_thread (arg=0x7fffffff7db0) at builtin-top.c:1114
#17 0x00007ffff7bb817a in start_thread () from /lib64/libpthread.so.0
#18 0x00007ffff5656dc3 in clone () from /lib64/libc.so.6
If you look at the frame #2, the code is:
488 if (he->srcline) {
489 he->srcline = strdup(he->srcline);
490 if (he->srcline == NULL)
491 goto err_rawdata;
492 }
If he->srcline is not NULL (it is not NULL if it is uninitialized rubbish),
it gets strdupped and strdupping a rubbish random string causes the problem.
Also, if you look at the commit 1fb7d06a50, it adds the srcline property
into the struct, but not initializing it everywhere needed.
Committer notes:
Now I see, when using --ignore-callees=do_idle we end up here at line
2189 in add_callchain_ip():
2181 if (al.sym != NULL) {
2182 if (perf_hpp_list.parent && !*parent &&
2183 symbol__match_regex(al.sym, &parent_regex))
2184 *parent = al.sym;
2185 else if (have_ignore_callees && root_al &&
2186 symbol__match_regex(al.sym, &ignore_callees_regex)) {
2187 /* Treat this symbol as the root,
2188 forgetting its callees. */
2189 *root_al = al;
2190 callchain_cursor_reset(cursor);
2191 }
2192 }
And the al that doesn't have the ->srcline field initialized will be
copied to the root_al, so then, back to:
1211 int hist_entry_iter__add(struct hist_entry_iter *iter, struct addr_location *al,
1212 int max_stack_depth, void *arg)
1213 {
1214 int err, err2;
1215 struct map *alm = NULL;
1216
1217 if (al)
1218 alm = map__get(al->map);
1219
1220 err = sample__resolve_callchain(iter->sample, &callchain_cursor, &iter->parent,
1221 iter->evsel, al, max_stack_depth);
1222 if (err) {
1223 map__put(alm);
1224 return err;
1225 }
1226
1227 err = iter->ops->prepare_entry(iter, al);
1228 if (err)
1229 goto out;
1230
1231 err = iter->ops->add_single_entry(iter, al);
1232 if (err)
1233 goto out;
1234
That al at line 1221 is what hist_entry_iter__add() (called from
sample__resolve_callchain()) saw as 'root_al', and then:
iter->ops->add_single_entry(iter, al);
will go on with al->srcline with a bogus value, I'll add the above
sequence to the cset and apply, thanks!
Signed-off-by: Michael Petlan <mpetlan@redhat.com>
CC: Milian Wolff <milian.wolff@kdab.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Fixes: 1fb7d06a50 ("perf report Use srcline from callchain for hist entries")
Link: https //lore.kernel.org/r/20210719145332.29747-1-mpetlan@redhat.com
Reported-by: Juri Lelli <jlelli@redhat.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 040b8907cc upstream.
With the new static annotation, the compiler warns when the functions
are actually unused:
drivers/gpu/drm/rockchip/cdn-dp-core.c:1123:12: error: 'cdn_dp_resume' defined but not used [-Werror=unused-function]
1123 | static int cdn_dp_resume(struct device *dev)
| ^~~~~~~~~~~~~
Mark them __maybe_unused to suppress that warning as well.
[ Not so 'new' static annotations any more, and I removed the part of
the patch that added __maybe_unused to cdn_dp_suspend(), because it's
used by the shutdown/remove code.
So only the resume function ends up possibly unused if CONFIG_PM isn't
set - Linus ]
Fixes: 7c49abb4c2 ("drm/rockchip: cdn-dp-core: Make cdn_dp_core_suspend/resume static")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f4bb62e64c upstream.
In tipc_sk_enqueue() we use hardcoded 2 jiffies to extract
socket buffer from generic queue to particular socket.
The 2 jiffies is too short in case there are other high priority
tasks get CPU cycles for multiple jiffies update. As result, no
buffer could be enqueued to particular socket.
To solve this, we switch to use constant timeout 20msecs.
Then, the function will be expired between 2 jiffies (CONFIG_100HZ)
and 20 jiffies (CONFIG_1000HZ).
Fixes: c637c10355 ("tipc: resolve race problem at unicast message reception")
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e3f0cc1a94 upstream.
A number of users have reported that they were not able to get the PHY
to successfully link up, especially after commit c36757eb9d ("net:
phy: consider AN_RESTART status when reading link status") where we
stopped reading just BMSR, but we also read BMCR to determine the link
status.
Andrius at NetBSD did a wonderful job at debugging the problem
and found out that the MDIO bus clock frequency would be incorrectly set
back to its default value which would prevent the MDIO bus controller
from reading PHY registers properly. Back when we only read BMSR, if we
read all 1s, we could falsely indicate a link status, though in general
there is a cable plugged in, so this went unnoticed. After a second read
of BMCR was added, a wrong read will lead to the inability to determine
a link UP condition which is when it started to be visibly broken, even
if it was long before that.
The fix consists in restoring the value of the MD_CSR register that was
set prior to the MAC reset.
Link: http://gnats.netbsd.org/cgi-bin/query-pr-single.pl?number=53494
Fixes: 90f750a81a ("r6040: consolidate MAC reset to its own function")
Reported-by: Andrius V <vezhlys@gmail.com>
Reported-by: Darek Strugacz <darek.strugacz@op.pl>
Tested-by: Darek Strugacz <darek.strugacz@op.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b6ff7eb66 upstream.
The reference count leak issue may take place in an error handling
path. If both conditions of tunnel->version == L2TP_HDR_VER_3 and the
return value of l2tp_v3_ensure_opt_in_linear is nonzero, the function
would directly jump to label invalid, without decrementing the reference
count of the l2tp_session object session increased earlier by
l2tp_tunnel_get_session(). This may result in refcount leaks.
Fix this issue by decrease the reference count before jumping to the
label invalid.
Fixes: 4522a70db7 ("l2tp: fix reading optional fields of L2TPv3")
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9ea761fdd upstream.
Commit 2677d20677 ("dccp: don't free ccid2_hc_tx_sock ...") fixed
a UAF but reintroduced CVE-2017-6074.
When the sock is cloned, two dccps_hc_tx_ccid will reference to the
same ccid. So one can free the ccid object twice from two socks after
cloning.
This issue was found by "Hadar Manor" as well and assigned with
CVE-2020-16119, which was fixed in Ubuntu's kernel. So here I port
the patch from Ubuntu to fix it.
The patch prevents cloned socks from referencing the same ccid.
Fixes: 2677d20677 ("dccp: don't free ccid2_hc_tx_sock ...")
Signed-off-by: Zhenpeng Lin <zplin@psu.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7366c23ff4 upstream.
Building dp83640.c on arch/parisc/ produces a build warning for
PAGE0 being redefined. Since the macro is not used in the dp83640
driver, just make it a comment for documentation purposes.
In file included from ../drivers/net/phy/dp83640.c:23:
../drivers/net/phy/dp83640_reg.h:8: warning: "PAGE0" redefined
8 | #define PAGE0 0x0000
from ../drivers/net/phy/dp83640.c:11:
../arch/parisc/include/asm/page.h:187: note: this is the location of the previous definition
187 | #define PAGE0 ((struct zeropage *)__PAGE_OFFSET)
Fixes: cb646e2b02 ("ptp: Added a clock driver for the National Semiconductor PHYTER.")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Richard Cochran <richard.cochran@omicron.at>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210913220605.19682-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c3a0a018e upstream.
Remove the assert from the callback priv lookup function since it does
not require RTNL lock and is already protected by flow_indr_block_lock.
This will avoid warnings from being emitted to dmesg if the driver
registers its callback after an ingress qdisc was created for a
netdevice.
The warnings started after the following patch was merged:
commit 74fc4f8287 ("net: Fix offloading indirect devices dependency on qdisc order creation")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc19862ffe upstream.
syzbot reported an use-after-free crash:
BUG: KASAN: use-after-free in tipc_recvmsg+0xf77/0xf90 net/tipc/socket.c:1979
Call Trace:
tipc_recvmsg+0xf77/0xf90 net/tipc/socket.c:1979
sock_recvmsg_nosec net/socket.c:943 [inline]
sock_recvmsg net/socket.c:961 [inline]
sock_recvmsg+0xca/0x110 net/socket.c:957
tipc_conn_rcv_from_sock+0x162/0x2f0 net/tipc/topsrv.c:398
tipc_conn_recv_work+0xeb/0x190 net/tipc/topsrv.c:421
process_one_work+0x98d/0x1630 kernel/workqueue.c:2276
worker_thread+0x658/0x11f0 kernel/workqueue.c:2422
As Hoang pointed out, it was caused by skb_cb->bytes_read still accessed
after calling tsk_advance_rx_queue() to free the skb in tipc_recvmsg().
This patch is to fix it by accessing skb_cb->bytes_read earlier than
calling tsk_advance_rx_queue().
Fixes: f4919ff59c ("tipc: keep the skb in rcv queue until the whole data is read")
Reported-by: syzbot+e6741b97d5552f97c24d@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 34b1999da9 upstream.
Jiri Olsa reported a fault when running:
# cat /proc/kallsyms | grep ksys_read
ffffffff8136d580 T ksys_read
# objdump -d --start-address=0xffffffff8136d580 --stop-address=0xffffffff8136d590 /proc/kcore
/proc/kcore: file format elf64-x86-64
Segmentation fault
general protection fault, probably for non-canonical address 0xf887ffcbff000: 0000 [#1] SMP PTI
CPU: 12 PID: 1079 Comm: objdump Not tainted 5.14.0-rc5qemu+ #508
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-4.fc34 04/01/2014
RIP: 0010:kern_addr_valid
Call Trace:
read_kcore
? rcu_read_lock_sched_held
? rcu_read_lock_sched_held
? rcu_read_lock_sched_held
? trace_hardirqs_on
? rcu_read_lock_sched_held
? lock_acquire
? lock_acquire
? rcu_read_lock_sched_held
? lock_acquire
? rcu_read_lock_sched_held
? rcu_read_lock_sched_held
? rcu_read_lock_sched_held
? lock_release
? _raw_spin_unlock
? __handle_mm_fault
? rcu_read_lock_sched_held
? lock_acquire
? rcu_read_lock_sched_held
? lock_release
proc_reg_read
? vfs_read
vfs_read
ksys_read
do_syscall_64
entry_SYSCALL_64_after_hwframe
The fault happens because kern_addr_valid() dereferences existent but not
present PMD in the high kernel mappings.
Such PMDs are created when free_kernel_image_pages() frees regions larger
than 2Mb. In this case, a part of the freed memory is mapped with PMDs and
the set_memory_np_noalias() -> ... -> __change_page_attr() sequence will
mark the PMD as not present rather than wipe it completely.
Have kern_addr_valid() check whether higher level page table entries are
present before trying to dereference them to fix this issue and to avoid
similar issues in the future.
Stable backporting note:
------------------------
Note that the stable marking is for all active stable branches because
there could be cases where pagetable entries exist but are not valid -
see 9a14aefc1d ("x86: cpa, fix lookup_address"), for example. So make
sure to be on the safe side here and use pXY_present() accessors rather
than pXY_none() which could #GP when accessing pages in the direct map.
Also see:
c40a56a781 ("x86/mm/init: Remove freed kernel image areas from alias mapping")
for more info.
Reported-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: Dave Hansen <dave.hansen@intel.com>
Tested-by: Jiri Olsa <jolsa@redhat.com>
Cc: <stable@vger.kernel.org> # 4.4+
Link: https://lkml.kernel.org/r/20210819132717.19358-1-rppt@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aeef8b5089 upstream.
The end address passed to memtype_reserve() is handed directly to
sanitize_phys(). However, end is exclusive and sanitize_phys() expects
an inclusive address. If end falls at the end of the physical address
space, sanitize_phys() will return 0. This can result in drivers
failing to load, and the following warning:
WARNING: CPU: 26 PID: 749 at arch/x86/mm/pat.c:354 reserve_memtype+0x262/0x450
reserve_memtype failed: [mem 0x3ffffff00000-0xffffffffffffffff], req uncached-minus
Call Trace:
[<ffffffffa427b1f2>] reserve_memtype+0x262/0x450
[<ffffffffa42764aa>] ioremap_nocache+0x1a/0x20
[<ffffffffc04620a1>] mpt3sas_base_map_resources+0x151/0xa60 [mpt3sas]
[<ffffffffc0465555>] mpt3sas_base_attach+0xf5/0xa50 [mpt3sas]
---[ end trace 6d6eea4438db89ef ]---
ioremap reserve_memtype failed -22
mpt3sas_cm0: unable to map adapter memory! or resource not found
mpt3sas_cm0: failure at drivers/scsi/mpt3sas/mpt3sas_scsih.c:10597/_scsih_probe()!
Fix this by passing the inclusive end address to sanitize_phys().
Fixes: 510ee090ab ("x86/mm/pat: Prepare {reserve, free}_memtype() for "decoy" addresses")
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/x49o8a3pu5i.fsf@segfault.boston.devel.redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f2faea8b64 upstream.
When we forcefully evict a mapping from the the address space and thus the
MMU context, the MMU context is leaked, as the mapping no longer points to
it, so it doesn't get freed when the GEM object is destroyed. Add the
mssing context put to fix the leak.
Cc: stable@vger.kernel.org # 5.4
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d6408538f0 upstream.
Move the refcount manipulation of the MMU context to the point where the
hardware state is programmed. At that point it is also known if a previous
MMU state is still there, or the state needs to be reprogrammed with a
potentially different context.
Cc: stable@vger.kernel.org # 5.4
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f3eea9d01 upstream.
The MMU state may be kept across a runtime suspend/resume cycle, as we
avoid a full hardware reset to keep the latency of the runtime PM small.
Don't pretend that the MMU state is lost in driver state. The MMU
context is pushed out when new HW jobs with a different context are
coming in. The only exception to this is when the GPU is unbound, in
which case we need to make sure to also free the last active context.
Cc: stable@vger.kernel.org # 5.4
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23e0f5a57d upstream.
While the DMA frontend can only be active when the MMU context is set, the
reverse isn't necessarily true, as the frontend can be stopped while the
MMU state is kept. Stop treating mmu_context being set as a indication that
the frontend is running and instead add a explicit property.
Cc: stable@vger.kernel.org # 5.4
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cda7532916 upstream.
The prev context is the MMU context at the time of the job
queueing in hardware. As a job might be queued multiple times
due to recovery after a GPU hang, we need to make sure to put
the stale prev MMU context from a prior queuing, to avoid the
reference and thus the MMU context leaking.
Cc: stable@vger.kernel.org # 5.4
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e35ac9d0b5 upstream.
When we need a buffer for SVE register state we call sve_alloc() to make
sure that one is there. In order to avoid repeated allocations and frees
we keep the buffer around unless we change vector length and just memset()
it to ensure a clean register state. The function that deals with this
takes the task to operate on as an argument, however in the case where we
do a memset() we initialise using the SVE state size for the current task
rather than the task passed as an argument.
This is only an issue in the case where we are setting the register state
for a task via ptrace and the task being configured has a different vector
length to the task tracing it. In the case where the buffer is larger in
the traced process we will leak old state from the traced process to
itself, in the case where the buffer is smaller in the traced process we
will overflow the buffer and corrupt memory.
Fixes: bc0ee47603 ("arm64/sve: Core task context handling")
Cc: <stable@vger.kernel.org> # 4.15.x
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210909165356.10675-1-broonie@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 16c8d2df7e upstream.
When setting up the next segment, we check what type the iter is and
handle it accordingly. However, when incrementing and processed amount
we do not, and both iter advance and addr/len are adjusted, regardless
of type. Split the increment side just like we do on the setup side.
Fixes: 4017eb91a9 ("io_uring: make loop_rw_iter() use original user supplied pointers")
Cc: stable@vger.kernel.org
Reported-by: Valentina Palmiotti <vpalmiotti@gmail.com>
Reviewed-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f93e834fa upstream.
The mount option max_inline ranges from 0 to the sectorsize (which is
now equal to page size). But we parse the mount options too early and
before the actual sectorsize is read from the superblock. So the upper
limit of max_inline is unaware of the actual sectorsize and is limited
by the temporary sectorsize 4096, even on a system where the default
sectorsize is 64K.
Fix this by reading the superblock sectorsize before the mount option
parse.
Reported-by: Alexander Tsvetkov <alexander.tsvetkov@oracle.com>
CC: stable@vger.kernel.org # 5.4+
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A failure of some CPU cores to come online has been traced to the
failure of a stm instruction while the cache is disabled. The symptom
is that the saved values read back as zeroes, a catastrophic error since
one of the values is a return address.
This patch forces a readback and retry until the correct value is
returned,
Notes:
At this stage in the boot process the core is running with its cache
disabled. Before enabling the cache its contents must be explicitly
invalidated, a process that requires quite a few registers that the
caller must preserve. Evidence suggests that something is writing a
block of zeroes over that space at a time when all other cores should
be idle, possibly some kind of write-combiner, and retrying is an
attempt to avoid the problem.
The previous attempted fix (forcing the accesses to only be 4-byte
aligned) appears to have only worked for a while and likely for less
obvious reasons such as a change in code alignment.
See: https://github.com/Hexxeh/rpi-firmware/issues/232
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
This reverts commit fe4cc0ed59.
The speculative patch that this commit reverts is proving to not be
effective any more, so revert it and try a new approach.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
commit b5fab34565 upstream.
In lock_region, simplify the calculation of the region_width parameter.
This field is the size, but encoded as ceil(log2(size)) - 1.
ceil(log2(size)) may be computed directly as fls(size - 1). However, we
want to use the 64-bit versions as the amount to lock can exceed
32-bits.
This avoids undefined (and completely wrong) behaviour when locking all
memory (size ~0). In this case, the old code would "round up" ~0 to the
nearest page, overflowing to 0. Since fls(0) == 0, this would calculate
a region width of 10 + 0 = 10. But then the code would shift by
(region_width - 11) = -1. As shifting by a negative number is undefined,
UBSAN flags the bug. Of course, even if it were defined the behaviour is
wrong, instead of locking all memory almost none would get locked.
The new form of the calculation corrects this special case and avoids
the undefined behaviour.
Signed-off-by: Alyssa Rosenzweig <alyssa.rosenzweig@collabora.com>
Reported-and-tested-by: Chris Morgan <macromorgan@hotmail.com>
Fixes: f3ba91228e ("drm/panfrost: Add initial panfrost driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Steven Price <steven.price@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210824173028.7528-2-alyssa.rosenzweig@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92bd92c44d upstream.
Commit 2f015ec6ea ("drm/dp_mst: Add sideband down request tracing +
selftests") added some debug code for sideband message tracing. But
it seems to have unintentionally changed the behavior on sideband message
failure. It catches and returns failure only if DRM_UT_DP is enabled.
Otherwise it ignores the error code and returns success. So on an MST
unplug, the caller is unaware that the clear payload message failed and
ends up waiting for 4 seconds for the response. Fixes the issue by
returning the proper error code.
Changes in V2:
-- Revise commit text as review comment
-- add Fixes text
Changes in V3:
-- remove "unlikely" optimization
Fixes: 2f015ec6ea ("drm/dp_mst: Add sideband down request tracing + selftests")
Cc: <stable@vger.kernel.org> # v5.5+
Signed-off-by: Rajkumar Subbiah <rsubbia@codeaurora.org>
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1625585434-9562-1-git-send-email-khsieh@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 552799f8b3 upstream.
Currently, outgoing packets larger than 1496 bytes are dropped when
tagged VLAN is used on a switch port.
Add the frame check sequence length to the value of the register
GSWIP_MAC_FLEN to fix this. This matches the lantiq_ppa vendor driver,
which uses a value consisting of 1518 bytes for the MAC frame, plus the
lengths of special tag and VLAN tags.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Cc: stable@vger.kernel.org
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32b2397c1e upstream.
There is a use after free crash when the pmem driver tears down its
mapping while I/O is still inbound.
This is triggered by driver unbind, "ndctl destroy-namespace", while I/O
is in flight.
Fix the sequence of blk_cleanup_queue() vs memunmap().
The crash signature is of the form:
BUG: unable to handle page fault for address: ffffc90080200000
CPU: 36 PID: 9606 Comm: systemd-udevd
Call Trace:
? pmem_do_bvec+0xf9/0x3a0
? xas_alloc+0x55/0xd0
pmem_rw_page+0x4b/0x80
bdev_read_page+0x86/0xb0
do_mpage_readpage+0x5d4/0x7a0
? lru_cache_add+0xe/0x10
mpage_readpages+0xf9/0x1c0
? bd_link_disk_holder+0x1a0/0x1a0
blkdev_readpages+0x1d/0x20
read_pages+0x67/0x1a0
ndctl Call Trace in vmcore:
PID: 23473 TASK: ffff88c4fbbe8000 CPU: 1 COMMAND: "ndctl"
__schedule
schedule
blk_mq_freeze_queue_wait
blk_freeze_queue
blk_cleanup_queue
pmem_release_queue
devm_action_release
release_nodes
devres_release_all
device_release_driver_internal
device_driver_detach
unbind_store
Cc: <stable@vger.kernel.org>
Signed-off-by: sumiyawang <sumiyawang@tencent.com>
Reviewed-by: yongduan <yongduan@tencent.com>
Link: https://lore.kernel.org/r/1629632949-14749-1-git-send-email-sumiyawang@tencent.com
Fixes: 50f44ee724 ("mm/devm_memremap_pages: fix final page put race")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fab827dbee upstream.
Commit 5d097056c9 ("kmemcg: account certain kmem allocations to memcg")
enabled memcg accounting for pids allocated from init_pid_ns.pid_cachep,
but forgot to adjust the setting for nested pid namespaces. As a result,
pid memory is not accounted exactly where it is really needed, inside
memcg-limited containers with their own pid namespaces.
Pid was one the first kernel objects enabled for memcg accounting.
init_pid_ns.pid_cachep marked by SLAB_ACCOUNT and we can expect that any
new pids in the system are memcg-accounted.
Though recently I've noticed that it is wrong. nested pid namespaces
creates own slab caches for pid objects, nested pids have increased size
because contain id both for all parent and for own pid namespaces. The
problem is that these slab caches are _NOT_ marked by SLAB_ACCOUNT, as a
result any pids allocated in nested pid namespaces are not
memcg-accounted.
Pid struct in nested pid namespace consumes up to 500 bytes memory, 100000
such objects gives us up to ~50Mb unaccounted memory, this allow container
to exceed assigned memcg limits.
Link: https://lkml.kernel.org/r/8b6de616-fd1a-02c6-cbdb-976ecdcfa604@virtuozzo.com
Fixes: 5d097056c9 ("kmemcg: account certain kmem allocations to memcg")
Cc: stable@vger.kernel.org
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Reviewed-by: Michal Koutný <mkoutny@suse.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Acked-by: Roman Gushchin <guro@fb.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32d4f4b782 upstream.
Commit f56ce412a5 ("mm: memcontrol: fix occasional OOMs due to
proportional memory.low reclaim") introduced a divide by zero corner
case when oomd is being used in combination with cgroup memory.low
protection.
When oomd decides to kill a cgroup, it will force the cgroup memory to
be reclaimed after killing the tasks, by writing to the memory.max file
for that cgroup, forcing the remaining page cache and reclaimable slab
to be reclaimed down to zero.
Previously, on cgroups with some memory.low protection that would result
in the memory being reclaimed down to the memory.low limit, or likely
not at all, having the page cache reclaimed asynchronously later.
With f56ce412a5 the oomd write to memory.max tries to reclaim all the
way down to zero, which may race with another reclaimer, to the point of
ending up with the divide by zero below.
This patch implements the obvious fix.
Link: https://lkml.kernel.org/r/20210826220149.058089c6@imladris.surriel.com
Fixes: f56ce412a5 ("mm: memcontrol: fix occasional OOMs due to proportional memory.low reclaim")
Signed-off-by: Rik van Riel <riel@surriel.com>
Acked-by: Roman Gushchin <guro@fb.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Chris Down <chris@chrisdown.name>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09a26e8327 upstream.
Guillaume Morin reported hitting the following WARNING followed by GPF or
NULL pointer deference either in cgroups_destroy or in the kill_css path.:
percpu ref (css_release) <= 0 (-1) after switching to atomic
WARNING: CPU: 23 PID: 130 at lib/percpu-refcount.c:196 percpu_ref_switch_to_atomic_rcu+0x127/0x130
CPU: 23 PID: 130 Comm: ksoftirqd/23 Kdump: loaded Tainted: G O 5.10.60 #1
RIP: 0010:percpu_ref_switch_to_atomic_rcu+0x127/0x130
Call Trace:
rcu_core+0x30f/0x530
rcu_core_si+0xe/0x10
__do_softirq+0x103/0x2a2
run_ksoftirqd+0x2b/0x40
smpboot_thread_fn+0x11a/0x170
kthread+0x10a/0x140
ret_from_fork+0x22/0x30
Upon further examination, it was discovered that the css structure was
associated with hugetlb reservations.
For private hugetlb mappings the vma points to a reserve map that
contains a pointer to the css. At mmap time, reservations are set up
and a reference to the css is taken. This reference is dropped in the
vma close operation; hugetlb_vm_op_close. However, if a vma is split no
additional reference to the css is taken yet hugetlb_vm_op_close will be
called twice for the split vma resulting in an underflow.
Fix by taking another reference in hugetlb_vm_op_open. Note that the
reference is only taken for the owner of the reserve map. In the more
common fork case, the pointer to the reserve map is cleared for
non-owning vmas.
Link: https://lkml.kernel.org/r/20210830215015.155224-1-mike.kravetz@oracle.com
Fixes: e9fe92ae0c ("hugetlb_cgroup: add reservation accounting for private mappings")
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Reported-by: Guillaume Morin <guillaume@morinfr.org>
Suggested-by: Guillaume Morin <guillaume@morinfr.org>
Tested-by: Guillaume Morin <guillaume@morinfr.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93ebb68287 upstream.
Since commit 903cd0f315 ("swiotlb: Use is_swiotlb_force_bounce for
swiotlb data bouncing") if code sets swiotlb_force it needs to do so
before the swiotlb is initialised. Otherwise
io_tlb_default_mem->force_bounce will not get set to true, and devices
that use (the default) swiotlb will not bounce despite switolb_force
having the value of SWIOTLB_FORCE.
Let us restore swiotlb functionality for PV by fulfilling this new
requirement.
This change addresses what turned out to be a fragility in
commit 64e1f0c531 ("s390/mm: force swiotlb for protected
virtualization"), which ain't exactly broken in its original context,
but could give us some more headache if people backport the broken
change and forget this fix.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Fixes: 903cd0f315 ("swiotlb: Use is_swiotlb_force_bounce for swiotlb data bouncing")
Fixes: 64e1f0c531 ("s390/mm: force swiotlb for protected virtualization")
Cc: stable@vger.kernel.org #5.3+
Signed-off-by: Konrad Rzeszutek Wilk <konrad@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f34ee9cb2c upstream.
In the numa=off kernel command-line configuration init_chip_info() loops
around the number of chips and attempts to copy the cpumask of that node
which is NULL for all iterations after the first chip.
Hence, store the cpu mask for each chip instead of derving cpumask from
node while populating the "chips" struct array and copy that to the
chips[i].mask
Fixes: 053819e0bf ("cpufreq: powernv: Handle throttling due to Pmax capping at chip level")
Cc: stable@vger.kernel.org # v4.3+
Reported-by: Shirisha Ganta <shirisha.ganta1@ibm.com>
Signed-off-by: Pratik R. Sampat <psampat@linux.ibm.com>
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
[mpe: Rename goto label to out_free_chip_cpu_mask]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210728120500.87549-2-psampat@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 030f653078 upstream.
I was debugging some crashes on parisc and I found out that there is a
crash possibility if a function using alloca is interrupted by a signal.
The reason for the crash is that the gcc alloca implementation leaves
garbage in the upper 32 bits of the sp register. This normally doesn't
matter (the upper bits are ignored because the PSW W-bit is clear),
however the signal delivery routine in the kernel uses full 64 bits of sp
and it fails with -EFAULT if the upper 32 bits are not zero.
I created this program that demonstrates the problem:
#include <stdlib.h>
#include <unistd.h>
#include <signal.h>
#include <alloca.h>
static __attribute__((noinline,noclone)) void aa(int *size)
{
void * volatile p = alloca(-*size);
while (1) ;
}
static void handler(int sig)
{
write(1, "signal delivered\n", 17);
_exit(0);
}
int main(void)
{
int size = -0x100;
signal(SIGALRM, handler);
alarm(1);
aa(&size);
}
If you compile it with optimizations, it will crash.
The "aa" function has this disassembly:
000106a0 <aa>:
106a0: 08 03 02 41 copy r3,r1
106a4: 08 1e 02 43 copy sp,r3
106a8: 6f c1 00 80 stw,ma r1,40(sp)
106ac: 37 dc 3f c1 ldo -20(sp),ret0
106b0: 0c 7c 12 90 stw ret0,8(r3)
106b4: 0f 40 10 9c ldw 0(r26),ret0 ; ret0 = 0x00000000FFFFFF00
106b8: 97 9c 00 7e subi 3f,ret0,ret0 ; ret0 = 0xFFFFFFFF0000013F
106bc: d7 80 1c 1a depwi 0,31,6,ret0 ; ret0 = 0xFFFFFFFF00000100
106c0: 0b 9e 0a 1e add,l sp,ret0,sp ; sp = 0xFFFFFFFFxxxxxxxx
106c4: e8 1f 1f f7 b,l,n 106c4 <aa+0x24>,r0
This patch fixes the bug by truncating the "usp" variable to 32 bits.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 632546c4b5 ]
io_size and iov_count in io_read() and io_write() hold the same value,
kill the last one.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e79c0e324b ]
abs() returns signed long, which could not convert the type
as unsigned, and it may cause a mismatch type warning from
static tools. To fix it, this patch uses an variable to save
the abs()'s result and does a explicit conversion.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a39ff4a47f ]
It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 733c99ee8b ]
In netlbl_cipsov4_add_std() when 'doi_def->map.std' alloc
failed, we sometime observe panic:
BUG: kernel NULL pointer dereference, address:
...
RIP: 0010:cipso_v4_doi_free+0x3a/0x80
...
Call Trace:
netlbl_cipsov4_add_std+0xf4/0x8c0
netlbl_cipsov4_add+0x13f/0x1b0
genl_family_rcv_msg_doit.isra.15+0x132/0x170
genl_rcv_msg+0x125/0x240
This is because in cipso_v4_doi_free() there is no check
on 'doi_def->map.std' when 'doi_def->type' equal 1, which
is possibe, since netlbl_cipsov4_add_std() haven't initialize
it before alloc 'doi_def->map.std'.
This patch just add the check to prevent panic happen for similar
cases.
Reported-by: Abaci <abaci@linux.alibaba.com>
Signed-off-by: Michael Wang <yun.wang@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c48662b9d ]
The problem is that gpio_free() can sleep and the cfg_soc() can be
called with spinlocks held. One problematic call tree is:
--> ath_reset_internal() takes &sc->sc_pcu_lock spin lock
--> ath9k_hw_reset()
--> ath9k_hw_gpio_request_in()
--> ath9k_hw_gpio_request()
--> ath9k_hw_gpio_cfg_soc()
Remove gpio_free(), use error message instead, so we should make sure
there is no GPIO conflict.
Also remove ath9k_hw_gpio_free() from ath9k_hw_apply_gpio_override(),
as gpio_mask will never be set for SOC chips.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1628481916-15030-1-git-send-email-miaoqing@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23151b9ae7 ]
Bad header can have large length field which can cause OOB.
cptr is the last bytes for read, and the eeprom is parsed
from high to low address. The OOB, triggered by the condition
length > cptr could cause memory error with a read on
negative index.
There are some sanity check around length, but it is not
compared with cptr (the remaining bytes). Here, the
corrupted/bad EEPROM can cause panic.
I was able to reproduce the crash, but I cannot find the
log and the reproducer now. After I applied the patch, the
bug is no longer reproducible.
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YM3xKsQJ0Hw2hjrc@Zekuns-MBP-16.fios-router.home
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0be883a0d7 ]
The check for count appears to be incorrect since a non-zero count
check occurs a couple of statements earlier. Currently the check is
always false and the dev->port->irq != PARPORT_IRQ_NONE part of the
check is never tested and the if statement is dead-code. Fix this
by removing the check on count.
Note that this code is pre-git history, so I can't find a sha for
it.
Acked-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Logically dead code")
Link: https://lore.kernel.org/r/20210730100710.27405-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec449ed823 ]
Under high stress, SW steering might get stuck on polling for completion
that never comes.
For such cases QP needs to have protocol retransmission mechanism enabled.
Currently the retransmission timeout is defined as 0 (unlimited). Fix this
by defining a real timeout.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6cc64770fb ]
In line 849 (#1), "mlx5dr_htbl_put(cur_htbl);" drops the reference to
cur_htbl and may cause cur_htbl to be freed.
However, cur_htbl is subsequently used in the next line, which may result
in an use-after-free bug.
Fix this by calling mlx5dr_err() before the cur_htbl is put.
Signed-off-by: Wentao_Liang <Wentao_Liang_g@163.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c6ce1c74ef ]
When TVQM is enabled (iwl_mvm_has_new_tx_api() is true), then
queue numbers are just sequentially assigned 0, 1, 2, ...
Prior to TVQM, in DQA, there were some statically allocated
queue numbers:
* IWL_MVM_DQA_AUX_QUEUE == 1,
* both IWL_MVM_DQA_INJECT_MONITOR_QUEUE and
IWL_MVM_DQA_P2P_DEVICE_QUEUE == 2, and
* IWL_MVM_DQA_AP_PROBE_RESP_QUEUE == 9.
Now, these values are assigned to the members mvm->aux_queue,
mvm->snif_queue, mvm->probe_queue and mvm->p2p_dev_queue by
default. Normally, this doesn't really matter, and if TVQM is
in fact available we override them to the real values after
allocating a queue for use there.
However, this allocation doesn't always happen. For example,
for mvm->p2p_dev_queue (== 2) it only happens when the P2P
Device interface is started, if any. If it's not started, the
value in mvm->p2p_dev_queue remains 2. This wouldn't really
matter all that much if it weren't for iwl_mvm_is_static_queue()
which checks a queue number against one of those four static
numbers.
Now, if no P2P Device or monitor interface is added then queue
2 may be dynamically allocated, yet alias mvm->p2p_dev_queue or
mvm->snif_queue, and thus iwl_mvm_is_static_queue() erroneously
returns true for it. If it then gets full, all interface queues
are stopped, instead of just backpressuring against the one TXQ
that's really the only affected one.
This clearly can lead to issues, as everything is stopped even
if just a single TXQ filled its corresponding HW queue, if it
happens to have an appropriate number (2 or 9, AUX is always
reassigned.) Due to a mac80211 bug, this also led to a situation
in which the queues remained stopped across a deauthentication
and then attempts to connect to a new AP started failing, but
that's fixed separately.
Fix all of this by simply initializing the queue numbers to
the invalid value until they're used, if TVQM is enabled, and
also setting them back to that value when the queues are later
freed again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802172232.2e47e623f9e2.I9b0830dafbb68ef35b7b8f0f46160abec02ac7d0@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ec06c2dee ]
On systems with multiple SH per SE compute_static_thread_mgmt_se#
is split into independent masks, one for each SH, in the upper and
lower 16 bits. We need to detect this and apply cu masking to each
SH. The cu mask bits are assigned first to each SE, then to
alternate SHs, then finally to higher CU id. This ensures that
the maximum number of SPIs are engaged as early as possible while
balancing CU assignment to each SH.
v2: Use max SH/SE rather than max SH in cu_per_sh.
v3: Fix comment blocks, ensure se_mask is initially zero filled,
and correctly assign se.sh.cu positions to unset bits in cu_mask.
Signed-off-by: Sean Keely <Sean.Keely@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66cce9e73e ]
When a remote usb device is attached to the local Virtual USB
Host Controller Root Hub port, the bound device driver may send
a port reset command.
vhci_hcd accepts port resets only when the device doesn't have
port address assigned to it. When reset happens device is in
assigned/used state and vhci_hcd rejects it leaving the port in
a stuck state.
This problem was found when a blue-tooth or xbox wireless dongle
was passed through using usbip.
A few drivers reset the port during probe including mt76 driver
specific to this bug report. Fix the problem with a change to
honor reset requests when device is in used state (VDEV_ST_USED).
Reported-and-tested-by: Michael <msbroadf@gmail.com>
Suggested-by: Michael <msbroadf@gmail.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210819225937.41037-1-skhan@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c75bde329 ]
If IRQ occurs between calling dsps_setup_optional_vbus_irq()
and dsps_create_musb_pdev(), then null pointer dereference occurs
since glue->musb wasn't initialized yet.
The patch puts initializing of neccesery data before registration
of the interrupt handler.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Link: https://lore.kernel.org/r/20210819163323.17714-1-lutovinova@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2847c46c61 ]
This reverts commit 5d5323a6f3.
That commit effectively disabled Intel host initiated U1/U2 lpm for devices
with periodic endpoints.
Before that commit we disabled host initiated U1/U2 lpm if the exit latency
was larger than any periodic endpoint service interval, this is according
to xhci spec xhci 1.1 specification section 4.23.5.2
After that commit we incorrectly checked that service interval was smaller
than U1/U2 inactivity timeout. This is not relevant, and can't happen for
Intel hosts as previously set U1/U2 timeout = 105% * service interval.
Patch claimed it solved cases where devices can't be enumerated because of
bandwidth issues. This might be true but it's a side effect of accidentally
turning off lpm.
exit latency calculations have been revised since then
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210820123503.2605901-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d72c74197b ]
smb_buf is allocated by small_smb_init_no_tc(), and buf type is
CIFS_SMALL_BUFFER, so we should use cifs_small_buf_release() to
release it in failed path.
Signed-off-by: Ding Hui <dinghui@sangfor.com.cn>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e72a55f2e5 ]
When a read/write command is sent via ioctl to the kernel,
and the command fails, the actual error response of the emmc
is not sent to the user.
IOCTL read/write tests are carried out using commands
17 (Single BLock Read), 24 (Single Block Write),
18 (Multi Block Read), 25 (Multi Block Write)
The tests are carried out on a 64Gb emmc device. All of these
tests try to access an "out of range" sector address (0x09B2FFFF).
It is seen that without the patch the response received by the user
is not OUT_OF_RANGE error (R1 response 31st bit is not set) as per
JEDEC specification. After applying the patch proper response is seen.
This is because the function returns without copying the response to
the user in case of failure. This patch fixes the issue.
Hence, this memcpy is required whether we get an error response or not.
Therefor it is moved up from the current position up to immediately
after we have called mmc_wait_for_req().
The test code and the output of only the CMD17 is included in the
commit to limit the message length.
CMD17 (Test Code Snippet):
==========================
printf("Forming CMD%d\n", opt_idx);
/* single block read */
cmd.blksz = 512;
cmd.blocks = 1;
cmd.write_flag = 0;
cmd.opcode = 17;
//cmd.arg = atoi(argv[3]);
cmd.arg = 0x09B2FFFF;
/* Expecting response R1B */
cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_ADTC;
memset(data, 0, sizeof(__u8) * 512);
mmc_ioc_cmd_set_data(cmd, data);
printf("Sending CMD%d: ARG[0x%08x]\n", opt_idx, cmd.arg);
if(ioctl(fd, MMC_IOC_CMD, &cmd))
perror("Error");
printf("\nResponse: %08x\n", cmd.response[0]);
CMD17 (Output without patch):
=============================
test@test-LIVA-Z:~$ sudo ./mmc cmd_test /dev/mmcblk0 17
Entering the do_mmc_commands:Device: /dev/mmcblk0 nargs:4
Entering the do_mmc_commands:Device: /dev/mmcblk0 options[17, 0x09B2FFF]
Forming CMD17
Sending CMD17: ARG[0x09b2ffff]
Error: Connection timed out
Response: 00000000
(Incorrect response)
CMD17 (Output with patch):
==========================
test@test-LIVA-Z:~$ sudo ./mmc cmd_test /dev/mmcblk0 17
[sudo] password for test:
Entering the do_mmc_commands:Device: /dev/mmcblk0 nargs:4
Entering the do_mmc_commands:Device: /dev/mmcblk0 options[17, 09B2FFFF]
Forming CMD17
Sending CMD17: ARG[0x09b2ffff]
Error: Connection timed out
Response: 80000900
(Correct OUT_OF_ERROR response as per JEDEC specification)
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20210824191726.8296-1-nishadkamdar@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d82d73da3 ]
0Day robot observed that it's easily timeout on a heavy load host.
-------------------
# selftests: bpf: test_maps
# Fork 1024 tasks to 'test_update_delete'
# Fork 1024 tasks to 'test_update_delete'
# Fork 100 tasks to 'test_hashmap'
# Fork 100 tasks to 'test_hashmap_percpu'
# Fork 100 tasks to 'test_hashmap_sizes'
# Fork 100 tasks to 'test_hashmap_walk'
# Fork 100 tasks to 'test_arraymap'
# Fork 100 tasks to 'test_arraymap_percpu'
# Failed sockmap unexpected timeout
not ok 3 selftests: bpf: test_maps # exit=1
# selftests: bpf: test_lru_map
# nr_cpus:8
-------------------
Since this test will be scheduled by 0Day to a random host that could have
only a few cpus(2-8), enlarge the timeout to avoid a false NG report.
In practice, i tried to pin it to only one cpu by 'taskset 0x01 ./test_maps',
and knew 10S is likely enough, but i still perfer to a larger value 30.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20210820015556.23276-2-lizhijian@cn.fujitsu.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ac5e45291 ]
For unexplained reasons, the prescaler register for this device needs to
be cleared (set to 1) while performing a data read or else the command
will hang. This does not appear to affect the real clock rate sent out
on the bus, so I assume it's purely to work around a hardware bug.
During normal operation, the prescaler is already set to 1, so nothing
needs to be done. However, in "initial mode" (which is used for sub-MHz
clock speeds, like the core sets while enumerating cards), it's set to
128 and so we need to reset it during data reads. We currently fail to
do this for long reads.
This has no functional affect on the driver's operation currently
written, as the MMC core always sets a clock above 1MHz before
attempting any long reads. However, the core could conceivably set any
clock speed at any time and the driver should still work, so I think
this fix is worthwhile.
I personally encountered this issue while performing data recovery on an
external chip. My connections had poor signal integrity, so I modified
the core code to reduce the clock speed. Without this change, I saw the
card enumerate but was unable to actually read any data.
Writes don't seem to work in the situation described above even with
this change (and even if the workaround is extended to encompass data
write commands). I was not able to find a way to get them working.
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Link: https://lore.kernel.org/r/2fef280d8409ab0100c26c6ac7050227defd098d.1627818365.git.tommyhebb@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6211e9cb2f ]
Trying to boot without SYSFS, but with OF_DYNAMIC quickly
results in a crash:
[ 0.088460] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000070
[...]
[ 0.103927] CPU: 1 PID: 1 Comm: swapper/0 Not tainted 5.14.0-rc3 #4179
[ 0.105810] Hardware name: linux,dummy-virt (DT)
[ 0.107147] pstate: 80000005 (Nzcv daif -PAN -UAO -TCO BTYPE=--)
[ 0.108876] pc : kernfs_find_and_get_ns+0x3c/0x7c
[ 0.110244] lr : kernfs_find_and_get_ns+0x3c/0x7c
[...]
[ 0.134087] Call trace:
[ 0.134800] kernfs_find_and_get_ns+0x3c/0x7c
[ 0.136054] safe_name+0x4c/0xd0
[ 0.136994] __of_attach_node_sysfs+0xf8/0x124
[ 0.138287] of_core_init+0x90/0xfc
[ 0.139296] driver_init+0x30/0x4c
[ 0.140283] kernel_init_freeable+0x160/0x1b8
[ 0.141543] kernel_init+0x30/0x140
[ 0.142561] ret_from_fork+0x10/0x18
While not having sysfs isn't a very common option these days,
it is still expected that such configuration would work.
Paper over it by bailing out from __of_attach_node_sysfs() if
CONFIG_SYSFS isn't enabled.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210820144722.169226-1-maz@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3736127a3a ]
Function btrfs_lookup_data_extent calls btrfs_search_slot to verify if
the EXTENT_ITEM exists in the extent tree. btrfs_search_slot can return
values bellow zero if an error happened.
Function replay_one_extent currently checks if the search found
something (0 returned) and increments the reference, and if not, it
seems to evaluate as 'not found'.
Fix the condition by checking if the value was bellow zero and return
early.
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Marcos Paulo de Souza <mpdesouza@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db87db65c1 ]
> Hi Arnd,
>
> First bad commit (maybe != root cause):
>
> tree: https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git master
> head: 2f73937c9aa561e2082839bc1a8efaac75d6e244
> commit: 47fd22f2b8 [4771/5318] cs89x0: rework driver configuration
> config: m68k-randconfig-c003-20210804 (attached as .config)
> compiler: m68k-linux-gcc (GCC) 10.3.0
> reproduce (this is a W=1 build):
> wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
> chmod +x ~/bin/make.cross
> # https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/commit/?id=47fd22f2b84765a2f7e3f150282497b902624547
> git remote add linux-next https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git
> git fetch --no-tags linux-next master
> git checkout 47fd22f2b8
> # save the attached .config to linux build tree
> COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-10.3.0 make.cross ARCH=m68k
>
> If you fix the issue, kindly add following tag as appropriate
> Reported-by: kernel test robot <lkp@intel.com>
>
> All errors (new ones prefixed by >>):
>
> In file included from include/linux/kernel.h:19,
> from include/linux/list.h:9,
> from include/linux/module.h:12,
> from drivers/net/ethernet/cirrus/cs89x0.c:51:
> drivers/net/ethernet/cirrus/cs89x0.c: In function 'net_open':
> drivers/net/ethernet/cirrus/cs89x0.c:897:20: error: implicit declaration of function 'isa_virt_to_bus'; did you mean 'virt_to_bus'? [-Werror=implicit-function-declaration]
> 897 | (unsigned long)isa_virt_to_bus(lp->dma_buff));
> | ^~~~~~~~~~~~~~~
> include/linux/printk.h:141:17: note: in definition of macro 'no_printk'
> 141 | printk(fmt, ##__VA_ARGS__); \
> | ^~~~~~~~~~~
> drivers/net/ethernet/cirrus/cs89x0.c:86:3: note: in expansion of macro 'pr_debug'
> 86 | pr_##level(fmt, ##__VA_ARGS__); \
> | ^~~
> drivers/net/ethernet/cirrus/cs89x0.c:894:3: note: in expansion of macro 'cs89_dbg'
> 894 | cs89_dbg(1, debug, "%s: dma %lx %lx\n",
> | ^~~~~~~~
> >> drivers/net/ethernet/cirrus/cs89x0.c:914:3: error: implicit declaration of function 'disable_dma'; did you mean 'disable_irq'? [-Werror=implicit-function-declaration]
As far as I can tell, this is a bug with the m68kmmu architecture, not
with my driver:
The CONFIG_ISA_DMA_API option is provided for coldfire, which implements it,
but dragonball also sets the option as a side-effect, without actually
implementing
the interfaces. The patch below should fix it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8fb4df1f5 ]
'bp_ena' in Aura context is NIX block index, setting it
zero will always backpressure NIX0 block, even if NIXLF
belongs to NIX1. Hence fix this by setting it appropriately
based on NIX block address.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05e4588738 ]
The kernel test robot reports undefined reference after we report wakeup
reason to mac80211. This is because CONFIG_PM is not defined in the testing
configuration file. In fact, functions within wow.c are used if CONFIG_PM
is defined, so use CONFIG_PM to decide whether we build this file or not.
The reported messages are:
hppa-linux-ld: drivers/net/wireless/realtek/rtw88/wow.o: in function `rtw_wow_show_wakeup_reason':
>> (.text+0x6c4): undefined reference to `ieee80211_report_wowlan_wakeup'
>> hppa-linux-ld: (.text+0x6e0): undefined reference to `ieee80211_report_wowlan_wakeup'
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210728014335.8785-4-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02a55c0009 ]
In current wow flow, driver calls rtw_wow_fw_start and sleep for 100ms,
to wait firmware finish preliminary work and then update the value of
WOWLAN_WAKE_REASON register to zero. But later firmware will start wow
function with power-saving mode, in which mode the value of
WOWLAN_WAKE_REASON register is 0xea. So driver may get 0xea value and
return fail. We use read_poll_timeout instead to check the value to avoid
this issue.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210728014335.8785-2-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c626f3864b ]
In certain randconfigs, clang warns:
drivers/gpu/drm/exynos/exynos_drm_dma.c:121:19: warning: variable
'mapping' is uninitialized when used here [-Wuninitialized]
priv->mapping = mapping;
^~~~~~~
drivers/gpu/drm/exynos/exynos_drm_dma.c:111:16: note: initialize the
variable 'mapping' to silence this warning
void *mapping;
^
= NULL
1 warning generated.
This occurs when CONFIG_EXYNOS_IOMMU is enabled and both
CONFIG_ARM_DMA_USE_IOMMU and CONFIG_IOMMU_DMA are disabled, which makes
the code look like
void *mapping;
if (0)
mapping = arm_iommu_create_mapping()
else if (0)
mapping = iommu_get_domain_for_dev()
...
priv->mapping = mapping;
Add an else branch that initializes mapping to the -ENODEV error pointer
so that there is no more warning and the driver does not change during
runtime.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7de875b231 ]
Locks have two sets of op arrays, fl_lmops for the lock manager (lockd
or nfsd), fl_ops for the filesystem. The server-side lockd code has
been setting its own fl_ops, which leads to confusion (and crashes) in
the reexport case, where the filesystem expects to be the only one
setting fl_ops.
And there's no reason for it that I can see-the lm_get/put_owner ops do
the same job.
Reported-by: Daire Byrne <daire@dneg.com>
Tested-by: Daire Byrne <daire@dneg.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1340f80f0 ]
In the gfs2 withdraw sequence, the dlm protocol is unmounted with a call
to lm_unmount. After a withdraw, users are allowed to unmount the
withdrawn file system. But at that point we may still have glocks left
over that we need to free via unmount's call to gfs2_gl_hash_clear.
These glocks may have never been completed because of whatever problem
caused the withdraw (IO errors or whatever).
Before this patch, function gdlm_put_lock would still try to call into
dlm to unlock these leftover glocks, which resulted in dlm returning
-EINVAL because the lock space was abandoned. These glocks were never
freed because there was no mechanism after that to free them.
This patch adds a check to gdlm_put_lock to see if the locking protocol
was inactive (DFL_UNMOUNT flag) and if so, free the glock and not
make the invalid call into dlm.
I could have combined this "if" with the one that follows, related to
leftover glock LVBs, but I felt the code was more readable with its own
if clause.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83e5dcbece ]
When skipping the tests due to a lack of system support for MTE we
currently print a message saying FAIL which makes it look like the test
failed even though the test did actually report KSFT_SKIP, creating some
confusion. Change the error message to say SKIP instead so things are
clearer.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210819172902.56211-1-broonie@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 74fc4f8287 ]
Currently, when creating an ingress qdisc on an indirect device before
the driver registered for callbacks, the driver will not have a chance
to register its filter configuration callbacks.
To fix that, modify the code such that it keeps track of all the ingress
qdiscs that call flow_indr_dev_setup_offload(). When a driver calls
flow_indr_dev_register(), go through the list of tracked ingress qdiscs
and call the driver callback entry point so as to give it a chance to
register its callback.
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbe34165cc ]
Fix buf allocation size (it needs to be 2 bytes larger). Found when
__alloc_size() annotations were added to kmalloc() interfaces.
In file included from ./include/linux/string.h:253,
from ./include/linux/bitmap.h:10,
from ./include/linux/cpumask.h:12,
from ./arch/x86/include/asm/paravirt.h:17,
from ./arch/x86/include/asm/irqflags.h:63,
from ./include/linux/irqflags.h:16,
from ./include/linux/rcupdate.h:26,
from ./include/linux/rculist.h:11,
from ./include/linux/pid.h:5,
from ./include/linux/sched.h:14,
from ./include/linux/blkdev.h:5,
from drivers/staging/rts5208/rtsx_scsi.c:12:
In function 'get_ms_information',
inlined from 'ms_sp_cmnd' at drivers/staging/rts5208/rtsx_scsi.c:2877:12,
inlined from 'rtsx_scsi_handler' at drivers/staging/rts5208/rtsx_scsi.c:3247:12:
./include/linux/fortify-string.h:54:29: warning: '__builtin_memcpy' forming offset [106, 107] is out
of the bounds [0, 106] [-Warray-bounds]
54 | #define __underlying_memcpy __builtin_memcpy
| ^
./include/linux/fortify-string.h:417:2: note: in expansion of macro '__underlying_memcpy'
417 | __underlying_##op(p, q, __fortify_size); \
| ^~~~~~~~~~~~~
./include/linux/fortify-string.h:463:26: note: in expansion of macro '__fortify_memcpy_chk'
463 | #define memcpy(p, q, s) __fortify_memcpy_chk(p, q, s, \
| ^~~~~~~~~~~~~~~~~~~~
drivers/staging/rts5208/rtsx_scsi.c:2851:3: note: in expansion of macro 'memcpy'
2851 | memcpy(buf + i, ms_card->raw_sys_info, 96);
| ^~~~~~
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-staging@lists.linux.dev
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210818044252.1533634-1-keescook@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b16ac5bf73 ]
libbpf CI has reported send_signal test is flaky although
I am not able to reproduce it in my local environment.
But I am able to reproduce with on-demand libbpf CI ([1]).
Through code analysis, the following is possible reason.
The failed subtest runs bpf program in softirq environment.
Since bpf_send_signal() only sends to a fork of "test_progs"
process. If the underlying current task is
not "test_progs", bpf_send_signal() will not be triggered
and the subtest will fail.
To reduce the chances where the underlying process is not
the intended one, this patch boosted scheduling priority to
-20 (highest allowed by setpriority() call). And I did
10 runs with on-demand libbpf CI with this patch and I
didn't observe any failures.
[1] https://github.com/libbpf/libbpf/actions/workflows/ondemand.yml
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210817190923.3186725-1-yhs@fb.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3faa49bce ]
Since the original TFO server code was implemented in commit
168a8f5805 ("tcp: TCP Fast Open Server -
main code path") the TFO server code has supported the sysctl bit flag
TFO_SERVER_COOKIE_NOT_REQD. Currently, when the TFO_SERVER_ENABLE and
TFO_SERVER_COOKIE_NOT_REQD sysctl bit flags are set, a server connection
will accept a SYN with N bytes of data (N > 0) that has no TFO cookie,
create a new fast open connection, process the incoming data in the SYN,
and make the connection ready for accepting. After accepting, the
connection is ready for read()/recvmsg() to read the N bytes of data in
the SYN, ready for write()/sendmsg() calls and data transmissions to
transmit data.
This commit changes an edge case in this feature by changing this
behavior to apply to (N >= 0) bytes of data in the SYN rather than only
(N > 0) bytes of data in the SYN. Now, a server will accept a data-less
SYN without a TFO cookie if TFO_SERVER_COOKIE_NOT_REQD is set.
Caveat! While this enables a new kind of TFO (data-less empty-cookie
SYN), some firewall rules setup may not work if they assume such packets
are not legit TFOs and will filter them.
Signed-off-by: Luke Hsiao <lukehsiao@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20210816205105.2533289-1-luke.w.hsiao@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b69eea82d3 ]
Modern-day mapping_set_error has the ability to squash the usual
negative error code into something appropriate for long-term storage in
a struct address_space -- ENOSPC becomes AS_ENOSPC, and everything else
becomes EIO. iomap squashes /everything/ to EIO, just as XFS did before
that, but this doesn't make sense.
Fix this by making it so that we can pass ENOSPC to userspace when
writeback fails due to space problems.
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87b8061bad ]
This fixes two issues that cause the sysrq sequence to be inadvertently
aborted on SCIF serial consoles:
- a NUL character remains in the RX queue after a break has been detected,
which is then passed on to uart_handle_sysrq_char()
- the break interrupt is handled twice on controllers with multiplexed ERI
and BRI interrupts
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20210816162201.28801-1-uli+renesas@fpond.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 020d86fc0d ]
The 'required-opps' property is considered optional, hence remove
the pr_err() in of_parse_required_opp() when we find the property is
missing.
While at it, also fix the return value of
of_get_required_opp_performance_state() when of_parse_required_opp()
fails, return a -ENODEV instead of the -EINVAL.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cafae4cd62 ]
LE Enhanced Connection Complete contains the Local RPA used in the
connection which must be used when set otherwise there could problems
when pairing since the address used by the remote stack could be the
Local RPA:
BLUETOOTH CORE SPECIFICATION Version 5.2 | Vol 4, Part E
page 2396
'Resolvable Private Address being used by the local device for this
connection. This is only valid when the Own_Address_Type (from the
HCI_LE_Create_Connection, HCI_LE_Set_Advertising_Parameters,
HCI_LE_Set_Extended_Advertising_Parameters, or
HCI_LE_Extended_Create_Connection commands) is set to 0x02 or
0x03, and the Controller generated a resolvable private address for the
local device using a non-zero local IRK. For other Own_Address_Type
values, the Controller shall return all zeros.'
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e7006de6c2 ]
We cannot detect a (perhaps buggy) controller that is sending us
a completion for a request that was already completed (for example
sending a completion twice), this phenomenon was seen in the wild
a few times.
So to protect against this, we use the upper 4 msbits of the nvme sqe
command_id to use as a 4-bit generation counter and verify it matches
the existing request generation that is incrementing on every execution.
The 16-bit command_id structure now is constructed by:
| xxxx | xxxxxxxxxxxx |
gen request tag
This means that we are giving up some possible queue depth as 12 bits
allow for a maximum queue depth of 4095 instead of 65536, however we
never create such long queues anyways so no real harm done.
Suggested-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Acked-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Tested-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b01a9d0ca ]
We already validate it when receiving the c2hdata pdu header
and this is not changing so this is a redundant check.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f865d0292f ]
The documented compatible string for the CPUs found on Tegra132 is
"nvidia,tegra132-denver", rather than the previously used compatible
string "nvidia,denver".
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 70e740ad55 ]
The configuration of USB VBUS regulators was borrowed from downstream
kernel, which is incorrect because the corresponding GPIOs are connected
to PROX_EN (A501 3G model) and LED_EN pins in accordance to the board
schematics. USB works fine with both GPIOs being disabled, so remove the
bogus USB VBUS regulators. The USB VBUS of USB3 is supplied from the fixed
5v system regulator and device-mode USB1 doesn't have VBUS switches.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79f5962bae ]
The maximum MTU was set to 2304, which is the maximum MSDU size. While
this is valid for normal WLAN interfaces, it is too low for monitor
interfaces. A monitor interface may receive and inject MPDU frames, and
the maximum MPDU frame size is larger than 2304. The MPDU may also
contain an A-MSDU frame, in which case the size may be much larger than
the MTU limit. Since the maximum size of an A-MSDU depends on the PHY
mode of the transmitting STA, it is not possible to set an exact MTU
limit for a monitor interface. Now the maximum MTU for a monitor
interface is unrestricted.
Signed-off-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Link: https://lore.kernel.org/r/20210628123246.2070558-1-johan.almbladh@anyfinetworks.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 554594567b ]
The variable dc->clk_mgr is checked in:
if (dc->clk_mgr && dc->clk_mgr->funcs->get_clock)
This indicates dc->clk_mgr can be NULL.
However, it is dereferenced in:
if (!dc->clk_mgr->funcs->get_clock)
To fix this null-pointer dereference, check dc->clk_mgr and the function
pointer dc->clk_mgr->funcs->get_clock earlier, and return if one of them
is NULL.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Tuo Li <islituo@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a211260c34 ]
The variable val is declared without initialization, and its address is
passed to amdgpu_i2c_get_byte(). In this function, the value of val is
accessed in:
DRM_DEBUG("i2c 0x%02x 0x%02x read failed\n",
addr, *val);
Also, when amdgpu_i2c_get_byte() returns, val may remain uninitialized,
but it is accessed in:
val &= ~amdgpu_connector->router.ddc_mux_control_pin;
To fix this possible uninitialized-variable access, initialize val to 0 in
amdgpu_i2c_router_select_ddc_port().
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Tuo Li <islituo@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 979aa51967 ]
Fix the following smatch warning:
wait_func_handle_exec_timeout() warn: should '1 << ent->idx' be a 64 bit type?
Use 1ULL, to have a 64 bit type variable.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eran Ben Elisha <eranbe@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba316be1b6 ]
struct sock.sk_timer should be used as a sock cleanup timer. However,
SCO uses it to implement sock timeouts.
This causes issues because struct sock.sk_timer's callback is run in
an IRQ context, and the timer callback function sco_sock_timeout takes
a spin lock on the socket. However, other functions such as
sco_conn_del and sco_conn_ready take the spin lock with interrupts
enabled.
This inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} lock usage could
lead to deadlocks as reported by Syzbot [1]:
CPU0
----
lock(slock-AF_BLUETOOTH-BTPROTO_SCO);
<Interrupt>
lock(slock-AF_BLUETOOTH-BTPROTO_SCO);
To fix this, we use delayed work to implement SCO sock timouts
instead. This allows us to avoid taking the spin lock on the socket in
an IRQ context, and corrects the misuse of struct sock.sk_timer.
As a note, cancel_delayed_work is used instead of
cancel_delayed_work_sync in sco_sock_set_timer and
sco_sock_clear_timer to avoid a deadlock. In the future, the call to
bh_lock_sock inside sco_sock_timeout should be changed to lock_sock to
synchronize with other functions using lock_sock. However, since
sco_sock_set_timer and sco_sock_clear_timer are sometimes called under
the locked socket (in sco_connect and __sco_sock_close),
cancel_delayed_work_sync might cause them to sleep until an
sco_sock_timeout that has started finishes running. But
sco_sock_timeout would also sleep until it can grab the lock_sock.
Using cancel_delayed_work is fine because sco_sock_timeout does not
change from run to run, hence there is no functional difference
between:
1. waiting for a timeout to finish running before scheduling another
timeout
2. scheduling another timeout while a timeout is running.
Link: https://syzkaller.appspot.com/bug?id=9089d89de0502e120f234ca0fc8a703f7368b31e [1]
Reported-by: syzbot+2f6d7c28bb4bf7e82060@syzkaller.appspotmail.com
Tested-by: syzbot+2f6d7c28bb4bf7e82060@syzkaller.appspotmail.com
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42716425ad ]
In tb_switch_default_link_ports(), while linking of ports,
only odd-numbered ports (1,3,5..) are considered and even-numbered
ports are not considered.
AMD host router has lane adapters at 2 and 3 and link ports at adapter 2
is not considered due to which lane bonding gets disabled.
Hence added a fix such that all ports are considered during
linking of ports.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a338619bd7 ]
When insmod zynqmp-dpsub.ko after rmmod it, system will hang with the
error log as below:
root@xilinx-zynqmp:~# insmod zynqmp-dpsub.ko
[ 88.391289] [drm] Initialized zynqmp-dpsub 1.0.0 20130509 for fd4a0000.display on minor 0
[ 88.529906] Console: switching to colour frame buffer device 128x48
[ 88.549402] zynqmp-dpsub fd4a0000.display: [drm] fb0: zynqmp-dpsubdrm frame buffer device
[ 88.571624] zynqmp-dpsub fd4a0000.display: ZynqMP DisplayPort Subsystem driver probed
root@xilinx-zynqmp:~# rmmod zynqmp_dpsub
[ 94.023404] Console: switching to colour dummy device 80x25
root@xilinx-zynqmp:~# insmod zynqmp-dpsub.ko
<hang here>
This is because that in zynqmp_dp_probe it tries to access some DP
registers while the DP controller is still in the reset state. When
running "rmmod zynqmp_dpsub", zynqmp_dp_reset(dp, true) in
zynqmp_dp_phy_exit is called to force the DP controller into the reset
state. Then insmod will call zynqmp_dp_probe to program the DP registers,
but at this moment the DP controller hasn't been brought out of the reset
state yet since the function zynqmp_dp_reset(dp, false) is called later and
this will result the system hang.
Releasing the reset to DP controller before any read/write operation to it
will fix this issue. And for symmetry, move zynqmp_dp_reset() call from
zynqmp_dp_phy_exit() to zynqmp_dp_remove().
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a19effb6db ]
The Runtime PM subsystem will force the device "fd4a0000.zynqmp-display"
to enter suspend state while booting if the following conditions are met:
- the usage counter is zero (pm_runtime_get_sync hasn't been called yet)
- no 'active' children (no zynqmp-dp-snd-xx node under dpsub node)
- no other device in the same power domain (dpdma node has no
"power-domains = <&zynqmp_firmware PD_DP>" property)
So there is a scenario as below:
1) DP device enters suspend state <- call zynqmp_gpd_power_off
2) zynqmp_disp_crtc_setup_clock <- configurate register VPLL_FRAC_CFG
3) pm_runtime_get_sync <- call zynqmp_gpd_power_on and clear previous
VPLL_FRAC_CFG configuration
4) clk_prepare_enable(disp->pclk) <- enable failed since VPLL_FRAC_CFG
configuration is corrupted
From above, we can see that pm_runtime_get_sync may clear register
VPLL_FRAC_CFG configuration and result the failure of clk enabling.
Putting pm_runtime_get_sync at the very beginning of the function
zynqmp_disp_crtc_atomic_enable can resolve this issue.
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56bd931ae5 ]
msm_atomic is doing vblank get/put's already,
currently there no need to duplicate the effort in MDP4
Fix warning:
...
WARNING: CPU: 3 PID: 79 at drivers/gpu/drm/drm_vblank.c:1194 drm_vblank_put+0x1cc/0x1d4
...
and multiple vblank time-outs:
...
msm 5100000.mdp: vblank time out, crtc=1
...
Tested on Nexus 7 2013 (deb), LTS 5.10.50.
Introduced by: 119ecb7fd3 ("drm/msm/mdp4: request vblank during modeset")
Signed-off-by: David Heidelberg <david@ixit.cz>
Link: https://lore.kernel.org/r/20210715060925.7880-1-david@ixit.cz
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4367355dd9 ]
When compiling with clang in certain configurations, an objtool warning
appears:
drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.o: warning: objtool:
ipq806x_gmac_probe() falls through to next function phy_modes()
This happens because the unreachable annotation in the third switch
statement is not eliminated. The compiler should know that the first
default case would prevent the second and third from being reached as
the comment notes but sanitizer options can make it harder for the
compiler to reason this out.
Help the compiler out by eliminating the unreachable() annotation and
unifying the default case error handling so that there is no objtool
warning, the meaning of the code stays the same, and there is less
duplication.
Reported-by: Sami Tolvanen <samitolvanen@google.com>
Tested-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84f3efbe5b ]
We have underscore (_) in node name leading to warning:
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: clocks: $nodename:0: 'clocks' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: clocks: xo_board: {'type': 'object'} is not allowed for {'compatible': ['fixed-clock'], '#clock-cells': [[0]], 'clock-frequency': [[19200000]], 'clock-output-names': ['xo_board'], 'phandle': [[115]]}
Fix this by changing node name to use dash (-)
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210308060826.3074234-10-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c678beca7 ]
We have underscore (_) in node name leading to warning:
arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon-cityman.dt.yaml: clocks: xo_board: {'type': 'object'} is not allowed for {'compatible': ['fixed-clock'], '#clock-cells': [[0]], 'clock-frequency': [[19200000]], 'phandle': [[26]]}
arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon-cityman.dt.yaml: clocks: sleep_clk: {'type': 'object'} is not allowed for {'compatible': ['fixed-clock'], '#clock-cells': [[0]], 'clock-frequency': [[32768]]}
Fix this by changing node name to use dash (-)
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210308060826.3074234-9-vkoul@kernel.org
[bjorn: Added clock-output-names to satisfy parent_names]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 52c9887fba ]
reg property should be array of values, here it is a single array,
leading to below warning:
arch/arm64/boot/dts/qcom/ipq8074-hk01.dt.yaml: soc: pci@10000000:reg:0: [268435456, 3869, 268439328, 168, 557056, 8192, 269484032, 4096] is too long
arch/arm64/boot/dts/qcom/ipq8074-hk01.dt.yaml: soc: pci@10000000:ranges: 'oneOf' conditional failed, one must be fixed:
arch/arm64/boot/dts/qcom/ipq8074-hk01.dt.yaml: soc: pci@10000000:ranges: 'oneOf' conditional failed, one must be fixed:
[[2164260864, 0, 270532608, 270532608, 0, 1048576, 2181038080, 0, 271581184, 271581184, 0, 13631488]] is not of type 'null'
[2164260864, 0, 270532608, 270532608, 0, 1048576, 2181038080, 0, 271581184, 271581184, 0, 13631488] is too long
arch/arm64/boot/dts/qcom/ipq8074-hk01.dt.yaml: soc: pci@20000000:reg:0: [536870912, 3869, 536874784, 168, 524288, 8192, 537919488, 4096] is too long
arch/arm64/boot/dts/qcom/ipq8074-hk01.dt.yaml: soc: pci@20000000:ranges: 'oneOf' conditional failed, one must be fixed:
arch/arm64/boot/dts/qcom/ipq8074-hk01.dt.yaml: soc: pci@20000000:ranges: 'oneOf' conditional failed, one must be fixed:
[[2164260864, 0, 538968064, 538968064, 0, 1048576, 2181038080, 0, 540016640, 540016640, 0, 13631488]] is not of type 'null'
[2164260864, 0, 538968064, 538968064, 0, 1048576, 2181038080, 0, 540016640, 540016640, 0, 13631488] is too long
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210308060826.3074234-17-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1fe0e1fa32 ]
Handle optional overrun-throttle-ms property as done for 8250_fsl in commit
6d7f677a2a ("serial: 8250: Rate limit serial port rx interrupts during
input overruns"). This can be used to rate limit the UART interrupts on
noisy lines that end up producing messages like the following:
ttyS ttyS2: 4 input overrun(s)
At least on droid4, the multiplexed USB and UART port is left to UART mode
by the bootloader for a debug console, and if a USB charger is connected
on boot, we get noise on the UART until the PMIC related drivers for PHY
and charger are loaded.
With this patch and overrun-throttle-ms = <500> we avoid the extra rx
interrupts.
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210727103533.51547-2-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d9b16054b ]
We must not call gfs2_consist (which does a file system withdraw) from
the freeze glock's freeze_go_xmote_bh function because the withdraw
will try to use the freeze glock, thus causing a glock recursion error.
This patch changes freeze_go_xmote_bh to call function
gfs2_assert_withdraw_delayed instead of gfs2_consist to avoid recursion.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4108b3e6db ]
These for-loops should test against v4l2_dv_timings_presets[i].bt.width,
not if i < v4l2_dv_timings_presets[i].bt.width. Luckily nothing ever broke,
since the smallest width is still a lot higher than the total number of
presets, but it is wrong.
The last item in the presets array is all 0, so the for-loop must stop
when it reaches that sentinel.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f809665ee7 ]
The range for analog gain mentioned in the datasheet is [0, 480].
The real gain formula mentioned in the datasheet is:
Gain = 512 / (512 – X)
Hence, values larger than 511 clearly makes no sense. The gain
register field is also documented to be of 9-bits in the datasheet.
Certainly, it is enough to infer that, the kernel driver currently
advertises an arbitrary analog gain max. Fix it by rectifying the
value as per the data sheet i.e. 480.
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51f93add36 ]
The frame_length_lines (0x0340) registers are hard-coded as follows:
- 4208x3118
frame_length_lines = 0x0c50
- 2104x1560
frame_length_lines = 0x0638
- 1048x780
frame_length_lines = 0x034c
The driver exposes the V4L2_CID_VBLANK control in read-only mode and
sets its value to vts_def - height, where vts_def is a mode-dependent
value coming from the supported_modes array. It is set using one of
the following macros defined in the driver:
#define IMX258_VTS_30FPS 0x0c98
#define IMX258_VTS_30FPS_2K 0x0638
#define IMX258_VTS_30FPS_VGA 0x034c
There's a clear mismatch in the value for the full resolution mode i.e.
IMX258_VTS_30FPS. Fix it by rectifying the macro with the value set for
the frame_length_lines register as stated above.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf2942a8b7 ]
The initialization sequence performed by the generic platform driver
pcie-designware-plat.c for a DWC based implementation doesn't work for
Tegra194. Tegra194 has a different initialization sequence requirement
which can only be satisfied by the Tegra194 specific platform driver
pcie-tegra194.c. So, remove the generic compatible string "snps,dw-pcie-ep"
from Tegra194's endpoint controller nodes.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 220ade7745 ]
Some time ago, I reported a calltrace issue
"did not find a suitable aggregator", please see[1].
After a period of analysis and reproduction, I find
that this problem is caused by concurrency.
Before the problem occurs, the bond structure is like follows:
bond0 - slaver0(eth0) - agg0.lag_ports -> port0 - port1
\
port0
\
slaver1(eth1) - agg1.lag_ports -> NULL
\
port1
If we run 'ifenslave bond0 -d eth1', the process is like below:
excuting __bond_release_one()
|
bond_upper_dev_unlink()[step1]
| | |
| | bond_3ad_lacpdu_recv()
| | ->bond_3ad_rx_indication()
| | spin_lock_bh()
| | ->ad_rx_machine()
| | ->__record_pdu()[step2]
| | spin_unlock_bh()
| | |
| bond_3ad_state_machine_handler()
| spin_lock_bh()
| ->ad_port_selection_logic()
| ->try to find free aggregator[step3]
| ->try to find suitable aggregator[step4]
| ->did not find a suitable aggregator[step5]
| spin_unlock_bh()
| |
| |
bond_3ad_unbind_slave() |
spin_lock_bh()
spin_unlock_bh()
step1: already removed slaver1(eth1) from list, but port1 remains
step2: receive a lacpdu and update port0
step3: port0 will be removed from agg0.lag_ports. The struct is
"agg0.lag_ports -> port1" now, and agg0 is not free. At the
same time, slaver1/agg1 has been removed from the list by step1.
So we can't find a free aggregator now.
step4: can't find suitable aggregator because of step2
step5: cause a calltrace since port->aggregator is NULL
To solve this concurrency problem, put bond_upper_dev_unlink()
after bond_3ad_unbind_slave(). In this way, we can invalid the port
first and skip this port in bond_3ad_state_machine_handler(). This
eliminates the situation that the slaver has been removed from the
list but the port is still valid.
[1]https://lore.kernel.org/netdev/10374.1611947473@famine/
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e6bc5987a ]
Swap reg and reg-names order and drop adi,input-justification
and adi,input-style to fix the following dtbs_check warnings:
arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dt.yaml: hdmi-transmitter@3d: adi,input-justification: False schema does not allow ['evenly']
arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dt.yaml: hdmi-transmitter@3d: adi,input-style: False schema does not allow [[1]]
arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dt.yaml: hdmi-transmitter@3d: reg-names:1: 'edid' was expected
arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dt.yaml: hdmi-transmitter@3d: reg-names:2: 'cec' was expected
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f728c4a9e8 ]
In error handling branch "if (WARN_ON(node == NUMA_NO_NODE))", the
previously allocated memories are not released. Doing this before
allocating memory eliminates memory leaks.
tj: Note that the condition only occurs when the arch code is pretty broken
and the WARN_ON might as well be BUG_ON().
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Reviewed-by: Lai Jiangshan <jiangshanlai@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 043c5bb3c4 ]
When loading in parallel multiple programs which use the same to-be
pinned map, it is possible that two instances of the loader will call
bpf_object__create_maps() at the same time. If the map doesn't exist
when both instances call bpf_object__reuse_map(), then one of the
instances will fail with EEXIST when calling bpf_map__pin().
Fix the race by retrying reusing a map if bpf_map__pin() returns
EEXIST. The fix is similar to the one in iproute2: e4c4685fd6e4 ("bpf:
Fix race condition with map pinning").
Before retrying the pinning, we don't do any special cleaning of an
internal map state. The closer code inspection revealed that it's not
required:
- bpf_object__create_map(): map->inner_map is destroyed after a
successful call, map->fd is closed if pinning fails.
- bpf_object__populate_internal_map(): created map elements is
destroyed upon close(map->fd).
- init_map_slots(): slots are freed after their initialization.
Signed-off-by: Martynas Pumputis <m@lambda.lt>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210726152001.34845-1-m@lambda.lt
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d07006f05 ]
The current behavior of 'tracex7' doesn't consist with other bpf samples
tracex{1..6}. Other samples do not require any argument to run with, but
tracex7 should be run with btrfs device argument. (it should be executed
with test_override_return.sh)
Currently, tracex7 doesn't have any description about how to run this
program and raises an unexpected error. And this result might be
confusing since users might not have a hunch about how to run this
program.
// Current behavior
# ./tracex7
sh: 1: Syntax error: word unexpected (expecting ")")
// Fixed behavior
# ./tracex7
ERROR: Run with the btrfs device argument!
In order to fix this error, this commit adds logic to report a message
and exit when running this program with a missing argument.
Additionally in test_override_return.sh, there is a problem with
multiple directory(tmpmnt) creation. So in this commit adds a line with
removing the directory with every execution.
Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20210727041056.23455-1-claudiajkang@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ccbdcc4d0 ]
The alloc_tty_driver failure is handled gracefully in hvsi_init. But
tty_register_driver is not. panic is called if that one fails.
So handle the failure of tty_register_driver gracefully too. This will
keep at least the console functional as it was enabled earlier by
console_initcall in hvsi_console_init. Instead of shooting down the
whole system.
This means, we disable interrupts and restore hvsi_wait back to
poll_for_state().
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210723074317.32690-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23411c7200 ]
While alloc_tty_driver failure in rs_init would mean we have much bigger
problem, there is no reason to panic when tty_register_driver fails
there. It can fail for various reasons.
So handle the failure gracefully. Actually handle them both while at it.
This will make at least the console functional as it was enabled earlier
by console_initcall in iss_console_init. Instead of shooting down the
whole system.
We move tty_port_init() after alloc_tty_driver(), so that we don't need
to destroy the port in case the latter function fails.
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: linux-xtensa@linux-xtensa.org
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210723074317.32690-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7aff291d0 ]
Oxford Semiconductor 950 serial port devices have a 128-byte FIFO and in
the enhanced (650) mode, which we select in `autoconfig_has_efr' with
the ECB bit set in the EFR register, they support the receive interrupt
trigger level selectable with FCR bits 7:6 from the set of 16, 32, 112,
120. This applies to the original OX16C950 discrete UART[1] as well as
950 cores embedded into more complex devices.
For these devices we set the default to 112, which sets an excessively
high level of 112 or 7/8 of the FIFO capacity, unlike with other port
types where we choose at most 1/2 of their respective FIFO capacities.
Additionally we don't make the trigger level configurable. Consequently
frequent input overruns happen with high bit rates where hardware flow
control cannot be used (e.g. terminal applications) even with otherwise
highly-performant systems.
Lower the default receive interrupt trigger level to 32 then, and make
it configurable. Document the trigger levels along with other port
types, including the set of 16, 32, 64, 112 for the transmit interrupt
as well[2].
References:
[1] "OX16C950 rev B High Performance UART with 128 byte FIFOs", Oxford
Semiconductor, Inc., DS-0031, Sep 05, Table 10: "Receiver Trigger
Levels", p. 22
[2] same, Table 9: "Transmit Interrupt Trigger Levels", p. 22
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260608480.37803@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3322ba0d7b ]
Kernel support for the newer PCI mio instructions can be toggled off
with the pci=nomio command line option which needs to integrate with
common code PCI option parsing. However this option then toggles static
branches which can't be toggled yet in an early_param() call.
Thus commit 9964f396f1 ("s390: fix setting of mio addressing control")
moved toggling the static branches to the PCI init routine.
With this setup however we can't check for mio support outside the PCI
code during early boot, i.e. before switching the static branches, which
we need to be able to export this as an ELF HWCAP.
Improve on this by turning mio availability into a machine flag that
gets initially set based on CONFIG_PCI and the facility bit and gets
toggled off if pci=nomio is found during PCI option parsing allowing
simple access to this machine flag after early init.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5492886c14 ]
In case of a jump label print the real address of the piece of code
where a mismatch was detected. This is right before the system panics,
so there is nothing revealed.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 323e0cb473 ]
Fix the following out-of-bounds warnings:
net/core/flow_dissector.c: In function '__skb_flow_dissect':
>> net/core/flow_dissector.c:1104:4: warning: 'memcpy' offset [24, 39] from the object at '<unknown>' is out of the bounds of referenced subobject 'saddr' with type 'struct in6_addr' at offset 8 [-Warray-bounds]
1104 | memcpy(&key_addrs->v6addrs, &iph->saddr,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1105 | sizeof(key_addrs->v6addrs));
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from include/linux/ipv6.h:5,
from net/core/flow_dissector.c:6:
include/uapi/linux/ipv6.h:133:18: note: subobject 'saddr' declared here
133 | struct in6_addr saddr;
| ^~~~~
>> net/core/flow_dissector.c:1059:4: warning: 'memcpy' offset [16, 19] from the object at '<unknown>' is out of the bounds of referenced subobject 'saddr' with type 'unsigned int' at offset 12 [-Warray-bounds]
1059 | memcpy(&key_addrs->v4addrs, &iph->saddr,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1060 | sizeof(key_addrs->v4addrs));
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from include/linux/ip.h:17,
from net/core/flow_dissector.c:5:
include/uapi/linux/ip.h:103:9: note: subobject 'saddr' declared here
103 | __be32 saddr;
| ^~~~~
The problem is that the original code is trying to copy data into a
couple of struct members adjacent to each other in a single call to
memcpy(). So, the compiler legitimately complains about it. As these
are just a couple of members, fix this by copying each one of them in
separate calls to memcpy().
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
Link: https://github.com/KSPP/linux/issues/109
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/d5ae2e65-1f18-2577-246f-bada7eee6ccd@intel.com/
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6321c7acb8 ]
Fix the following out-of-bounds warning:
In function 'ip_copy_addrs',
inlined from '__ip_queue_xmit' at net/ipv4/ip_output.c:517:2:
net/ipv4/ip_output.c:449:2: warning: 'memcpy' offset [40, 43] from the object at 'fl' is out of the bounds of referenced subobject 'saddr' with type 'unsigned int' at offset 36 [-Warray-bounds]
449 | memcpy(&iph->saddr, &fl4->saddr,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
450 | sizeof(fl4->saddr) + sizeof(fl4->daddr));
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The problem is that the original code is trying to copy data into a
couple of struct members adjacent to each other in a single call to
memcpy(). This causes a legitimate compiler warning because memcpy()
overruns the length of &iph->saddr and &fl4->saddr. As these are just
a couple of struct members, fix this by using direct assignments,
instead of memcpy().
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
Link: https://github.com/KSPP/linux/issues/109
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/d5ae2e65-1f18-2577-246f-bada7eee6ccd@intel.com/
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b7e9f25e5 ]
Each test case can have a set of sub-tests, where each sub-test can
run the cBPF/eBPF test snippet with its own data_size and expected
result. Before, the end of the sub-test array was indicated by both
data_size and result being zero. However, most or all of the internal
eBPF tests has a data_size of zero already. When such a test also had
an expected value of zero, the test was never run but reported as
PASS anyway.
Now the test runner always runs the first sub-test, regardless of the
data_size and result values. The sub-test array zero-termination only
applies for any additional sub-tests.
There are other ways fix it of course, but this solution at least
removes the surprise of eBPF tests with a zero result always succeeding.
Signed-off-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210721103822.3755111-1-johan.almbladh@anyfinetworks.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95f71f12aa ]
The printing message "PSP loading VCN firmware" is mis-leading because
people might think driver is loading VCN firmware. Actually when this
message is printed, driver is just preparing some VCN ucode, not loading
VCN firmware yet. The actual VCN firmware loading will be in the PSP block
hw_init. Fix the printing message
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Christian Konig <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd98d2895d ]
The ethtool compat ioctl handling is hidden away in net/socket.c,
which introduces a couple of minor oddities:
- The implementation may end up diverging, as seen in the RXNFC
extension in commit 84a1d9c482 ("net: ethtool: extend RXNFC
API to support RSS spreading of filter matches") that does not work
in compat mode.
- Most architectures do not need the compat handling at all
because u64 and compat_u64 have the same alignment.
- On x86, the conversion is done for both x32 and i386 user space,
but it's actually wrong to do it for x32 and cannot work there.
- On 32-bit Arm, it never worked for compat oabi user space, since
that needs to do the same conversion but does not.
- It would be nice to get rid of both compat_alloc_user_space()
and copy_in_user() throughout the kernel.
None of these actually seems to be a serious problem that real
users are likely to encounter, but fixing all of them actually
leads to code that is both shorter and more readable.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23e55639b8 ]
[why]
The units of the time_per_pixel variable were incorrect, this had to be
changed for the code to properly function.
[how]
The change was very straightforward, only required one line of code to
be changed where the calculation was done.
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Oliver Logush <oliver.logush@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8990f96a01 ]
Some versions of the MC firmware wrongly report 0 for register base
address of the DPMCP associated with child DPRC objects thus rendering
them unusable. This is particularly troublesome in ACPI boot scenarios
where the legacy way of extracting this base address from the device
tree does not apply.
Given that DPMCPs share the same base address, workaround this by using
the base address extracted from the root DPRC container.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Link: https://lore.kernel.org/r/20210715140718.8513-8-laurentiu.tudor@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df00609821 ]
On Armadillo-800-EVA with CONFIG_DEBUG_SPINLOCK=y:
BUG: spinlock bad magic on CPU#0, swapper/1
lock: lcdc0_device+0x10c/0x308, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
CPU: 0 PID: 1 Comm: swapper Not tainted 5.11.0-rc5-armadillo-00036-gbbca04be7a80-dirty #287
Hardware name: Generic R8A7740 (Flattened Device Tree)
[<c010c3c8>] (unwind_backtrace) from [<c010a49c>] (show_stack+0x10/0x14)
[<c010a49c>] (show_stack) from [<c0159534>] (do_raw_spin_lock+0x20/0x94)
[<c0159534>] (do_raw_spin_lock) from [<c040858c>] (dev_pm_get_subsys_data+0x8c/0x11c)
[<c040858c>] (dev_pm_get_subsys_data) from [<c05fbcac>] (genpd_add_device+0x78/0x2b8)
[<c05fbcac>] (genpd_add_device) from [<c0412db4>] (of_genpd_add_device+0x34/0x4c)
[<c0412db4>] (of_genpd_add_device) from [<c0a1ea74>] (board_staging_register_device+0x11c/0x148)
[<c0a1ea74>] (board_staging_register_device) from [<c0a1eac4>] (board_staging_register_devices+0x24/0x28)
of_genpd_add_device() is called before platform_device_register(), as it
needs to attach the genpd before the device is probed. But the spinlock
is only initialized when the device is registered.
Fix this by open-coding the spinlock initialization, cfr.
device_pm_init_common() in the internal drivers/base code, and in the
SuperH early platform code.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/57783ece7ddae55f2bda2f59f452180bff744ea0.1626257398.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bcacbf06c8 ]
Currently the composite driver encodes the MaxPower field of
the configuration descriptor by reading the c->MaxPower of the
usb_configuration only if it is non-zero, otherwise it falls back
to using the value hard-coded in CONFIG_USB_GADGET_VBUS_DRAW.
However, there are cases when a configuration must explicitly set
bMaxPower to 0, particularly if its bmAttributes also has the
Self-Powered bit set, which is a valid combination.
This is specifically called out in the USB PD specification section
9.1, in which a PDUSB device "shall report zero in the bMaxPower
field after negotiating a mutually agreeable Contract", and also
verified by the USB Type-C Functional Test TD.4.10.2 Sink Power
Precedence Test.
The fix allows the c->MaxPower to be used for encoding the bMaxPower
even if it is 0, if the self-powered bit is also set. An example
usage of this would be for a ConfigFS gadget to be dynamically
updated by userspace when the Type-C connection is determined to be
operating in Power Delivery mode.
Co-developed-by: Ronak Vijay Raheja <rraheja@codeaurora.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Ronak Vijay Raheja <rraheja@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20210720080907.30292-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61136a12cb ]
mv_ehci_enable() did not disable and unprepare clocks in case of
failures of phy_init(). Besides, it did not take into account failures
of ehci_clock_enable() (in effect, failures of clk_prepare_enable()).
The patch fixes both issues and gets rid of redundant wrappers around
clk_prepare_enable() and clk_disable_unprepare() to simplify this a bit.
Found by Linux Driver Verification project (linuxtesting.org).
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Link: https://lore.kernel.org/r/20210708083056.21543-1-novikov@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ae0123960 ]
f_ncm tx timeout can call us with null skb to flush
a pending frame. In this case skb is NULL to begin
with but ceases to be null after dev->wrap() completes.
In such a case in->maxpacket will be read, even though
we've failed to check that 'in' is not NULL.
Though I've never observed this fail in practice,
however the 'flush operation' simply does not make sense with
a null usb IN endpoint - there's nowhere to flush to...
(note that we're the gadget/device, and IN is from the point
of view of the host, so here IN actually means outbound...)
Cc: Brooke Basile <brookebasile@gmail.com>
Cc: "Bryan O'Donoghue" <bryan.odonoghue@linaro.org>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20210701114834.884597-6-zenczykowski@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 373e2829e7 ]
Ensure that the adapter->q_vector[MAX_Q_VECTORS] array isn't accessed
beyond its size. It was fixed by using a local variable num_q_vectors
as a limit for loop index, and ensure that num_q_vectors is not bigger
than MAX_Q_VECTORS.
Suggested-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fed31a4dd3 ]
This commit fixes several typos where CONFIG_TASKS_RCU_TRACE should
instead be CONFIG_TASKS_TRACE_RCU. Among other things, these typos
could cause CONFIG_TASKS_TRACE_RCU_READ_MB=y kernels to suffer from
memory-ordering bugs that could result in false-positive quiescent
states and too-short grace periods.
Signed-off-by: Zhouyi Zhou <zhouzhouyi@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56f0729a51 ]
drm_file->master pointers should be protected by
drm_device.master_mutex or drm_file.master_lookup_lock when being
dereferenced.
However, in drm_lease.c, there are multiple instances where
drm_file->master is accessed and dereferenced while neither lock is
held. This makes drm_lease.c vulnerable to use-after-free bugs.
We address this issue in 2 ways:
1. Add a new drm_file_get_master() function that calls drm_master_get
on drm_file->master while holding on to
drm_file.master_lookup_lock. Since drm_master_get increments the
reference count of master, this prevents master from being freed until
we unreference it with drm_master_put.
2. In each case where drm_file->master is directly accessed and
eventually dereferenced in drm_lease.c, we wrap the access in a call
to the new drm_file_get_master function, then unreference the master
pointer once we are done using it.
Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210712043508.11584-6-desmondcheongzx@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b0860a3cf ]
Currently, drm_file.master pointers should be protected by
drm_device.master_mutex when being dereferenced. This is because
drm_file.master is not invariant for the lifetime of drm_file. If
drm_file is not the creator of master, then drm_file.is_master is
false, and a call to drm_setmaster_ioctl will invoke
drm_new_set_master, which then allocates a new master for drm_file and
puts the old master.
Thus, without holding drm_device.master_mutex, the old value of
drm_file.master could be freed while it is being used by another
concurrent process.
However, it is not always possible to lock drm_device.master_mutex to
dereference drm_file.master. Through the fbdev emulation code, this
might occur in a deep nest of other locks. But drm_device.master_mutex
is also the outermost lock in the nesting hierarchy, so this leads to
potential deadlocks.
To address this, we introduce a new spin lock at the bottom of the
lock hierarchy that only serializes drm_file.master. With this change,
the value of drm_file.master changes only when both
drm_device.master_mutex and drm_file.master_lookup_lock are
held. Hence, any process holding either of those locks can ensure that
the value of drm_file.master will not change concurrently.
Since no lock depends on the new drm_file.master_lookup_lock, when
drm_file.master is dereferenced, but drm_device.master_mutex cannot be
held, we can safely protect the master pointer with
drm_file.master_lookup_lock.
Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210712043508.11584-5-desmondcheongzx@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5eff9585de ]
Inside drm_clients_info, the rcu_read_lock is held to lock
pid_task()->comm. However, within this protected section, a call to
drm_is_current_master is made, which involves a mutex lock in a future
patch. However, this is illegal because the mutex lock might block
while in the RCU read-side critical section.
Since drm_is_current_master isn't protected by rcu_read_lock, we avoid
this by moving it out of the RCU critical section.
The following report came from intel-gfx ci's
igt@debugfs_test@read_all_entries testcase:
=============================
[ BUG: Invalid wait context ]
5.13.0-CI-Patchwork_20515+ #1 Tainted: G W
-----------------------------
debugfs_test/1101 is trying to lock:
ffff888132d901a8 (&dev->master_mutex){+.+.}-{3:3}, at:
drm_is_current_master+0x1e/0x50
other info that might help us debug this:
context-{4:4}
3 locks held by debugfs_test/1101:
#0: ffff88810fdffc90 (&p->lock){+.+.}-{3:3}, at:
seq_read_iter+0x53/0x3b0
#1: ffff888132d90240 (&dev->filelist_mutex){+.+.}-{3:3}, at:
drm_clients_info+0x63/0x2a0
#2: ffffffff82734220 (rcu_read_lock){....}-{1:2}, at:
drm_clients_info+0x1b1/0x2a0
stack backtrace:
CPU: 8 PID: 1101 Comm: debugfs_test Tainted: G W
5.13.0-CI-Patchwork_20515+ #1
Hardware name: Intel Corporation CometLake Client Platform/CometLake S
UDIMM (ERB/CRB), BIOS CMLSFWR1.R00.1263.D00.1906260926 06/26/2019
Call Trace:
dump_stack+0x7f/0xad
__lock_acquire.cold.78+0x2af/0x2ca
lock_acquire+0xd3/0x300
? drm_is_current_master+0x1e/0x50
? __mutex_lock+0x76/0x970
? lockdep_hardirqs_on+0xbf/0x130
__mutex_lock+0xab/0x970
? drm_is_current_master+0x1e/0x50
? drm_is_current_master+0x1e/0x50
? drm_is_current_master+0x1e/0x50
drm_is_current_master+0x1e/0x50
drm_clients_info+0x107/0x2a0
seq_read_iter+0x178/0x3b0
seq_read+0x104/0x150
full_proxy_read+0x4e/0x80
vfs_read+0xa5/0x1b0
ksys_read+0x5a/0xd0
do_syscall_64+0x39/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210712043508.11584-3-desmondcheongzx@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d14f5c702 ]
In the smk_access_entry() function, if no matching rule is found
in the rust_list, a negative error code will be used to perform bit
operations with the MAY_ enumeration value. This is semantically
wrong. This patch fixes this issue.
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fef773fc81 ]
Yonghong Song report:
The bpf selftest tc_bpf failed with latest bpf-next.
The following is the command to run and the result:
$ ./test_progs -n 132
[ 40.947571] bpf_testmod: loading out-of-tree module taints kernel.
test_tc_bpf:PASS:test_tc_bpf__open_and_load 0 nsec
test_tc_bpf:PASS:bpf_tc_hook_create(BPF_TC_INGRESS) 0 nsec
test_tc_bpf:PASS:bpf_tc_hook_create invalid hook.attach_point 0 nsec
test_tc_bpf_basic:PASS:bpf_obj_get_info_by_fd 0 nsec
test_tc_bpf_basic:PASS:bpf_tc_attach 0 nsec
test_tc_bpf_basic:PASS:handle set 0 nsec
test_tc_bpf_basic:PASS:priority set 0 nsec
test_tc_bpf_basic:PASS:prog_id set 0 nsec
test_tc_bpf_basic:PASS:bpf_tc_attach replace mode 0 nsec
test_tc_bpf_basic:PASS:bpf_tc_query 0 nsec
test_tc_bpf_basic:PASS:handle set 0 nsec
test_tc_bpf_basic:PASS:priority set 0 nsec
test_tc_bpf_basic:PASS:prog_id set 0 nsec
libbpf: Kernel error message: Failed to send filter delete notification
test_tc_bpf_basic:FAIL:bpf_tc_detach unexpected error: -3 (errno 3)
test_tc_bpf:FAIL:test_tc_internal ingress unexpected error: -3 (errno 3)
The failure seems due to the commit
cfdf0d9ae7 ("rtnetlink: use nlmsg_notify() in rtnetlink_send()")
Deal with ESRCH error in nlmsg_notify() even the report variable is zero.
Reported-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Link: https://lore.kernel.org/r/20210719051816.11762-1-yajun.deng@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 98a6543917 ]
The user can pass in any value to the driver through the 'ioctl'
interface. The driver dost not check, which may cause DoS bugs.
The following log reveals it:
divide error: 0000 [#1] PREEMPT SMP KASAN PTI
RIP: 0010:SetOverlayViewPort+0x133/0x5f0 drivers/video/fbdev/kyro/STG4000OverlayDevice.c:476
Call Trace:
kyro_dev_overlay_viewport_set drivers/video/fbdev/kyro/fbdev.c:378 [inline]
kyrofb_ioctl+0x2eb/0x330 drivers/video/fbdev/kyro/fbdev.c:603
do_fb_ioctl+0x1f3/0x700 drivers/video/fbdev/core/fbmem.c:1171
fb_ioctl+0xeb/0x130 drivers/video/fbdev/core/fbmem.c:1185
vfs_ioctl fs/ioctl.c:48 [inline]
__do_sys_ioctl fs/ioctl.c:753 [inline]
__se_sys_ioctl fs/ioctl.c:739 [inline]
__x64_sys_ioctl+0x19b/0x220 fs/ioctl.c:739
do_syscall_64+0x32/0x80 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xae
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1626235762-2590-1-git-send-email-zheyuma97@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0dc6c59892 ]
Since new code doesn't take old clk names in account, it does fixes
error:
msm_dsi 4700000.mdss_dsi: dev_pm_opp_set_clkname: Couldn't find clock: -2
and following kernel oops introduced by
b0530eb119 ("drm/msm/dpu: Use OPP API to set clk/perf state").
Also removes warning about deprecated clock names.
Tested against linux-5.10.y LTS on Nexus 7 2013.
Reviewed-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: David Heidelberg <david@ixit.cz>
Link: https://lore.kernel.org/r/20210707131453.24041-1-david@ixit.cz
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 226d528512 ]
To avoid races between iavf_init_task(), iavf_reset_task(),
iavf_watchdog_task(), iavf_adminq_task() as well as the shutdown and
remove functions more locking is required.
The current protection by __IAVF_IN_CRITICAL_TASK is needed in
additional places.
- The reset task performs state transitions, therefore needs locking.
- The adminq task acts on replies from the PF in
iavf_virtchnl_completion() which may alter the states.
- The init task is not only run during probe but also if a VF gets stuck
to reinitialize it.
- The shutdown function performs a state transition.
- The remove function performs a state transition and also free's
resources.
iavf_lock_timeout() is introduced to avoid waiting infinitely
and cause a deadlock. Rather unlock and print a warning.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 22c8fd71d3 ]
The iavf watchdog task overrides adapter->state to __IAVF_RESETTING
when it detects a pending reset. Then schedules iavf_reset_task() which
takes care of the reset.
The reset task is capable of handling the reset without changing
adapter->state. In fact we lose the state information when the watchdog
task prematurely changes the adapter state. This may lead to a crash if
instead of the reset task the iavf_remove() function gets called before
the reset task.
In that case (if we were in state __IAVF_RUNNING previously) the
iavf_remove() function triggers iavf_close() which fails to close the
device because of the incorrect state information.
This may result in a crash due to pending interrupts.
kernel BUG at drivers/pci/msi.c:357!
[...]
Call Trace:
[<ffffffffbddf24dd>] pci_disable_msix+0x3d/0x50
[<ffffffffc08d2a63>] iavf_reset_interrupt_capability+0x23/0x40 [iavf]
[<ffffffffc08d312a>] iavf_remove+0x10a/0x350 [iavf]
[<ffffffffbddd3359>] pci_device_remove+0x39/0xc0
[<ffffffffbdeb492f>] __device_release_driver+0x7f/0xf0
[<ffffffffbdeb49c3>] device_release_driver+0x23/0x30
[<ffffffffbddcabb4>] pci_stop_bus_device+0x84/0xa0
[<ffffffffbddcacc2>] pci_stop_and_remove_bus_device+0x12/0x20
[<ffffffffbddf361f>] pci_iov_remove_virtfn+0xaf/0x160
[<ffffffffbddf3bcc>] sriov_disable+0x3c/0xf0
[<ffffffffbddf3ca3>] pci_disable_sriov+0x23/0x30
[<ffffffffc0667365>] i40e_free_vfs+0x265/0x2d0 [i40e]
[<ffffffffc0667624>] i40e_pci_sriov_configure+0x144/0x1f0 [i40e]
[<ffffffffbddd5307>] sriov_numvfs_store+0x177/0x1d0
Code: 00 00 e8 3c 25 e3 ff 49 c7 86 88 08 00 00 00 00 00 00 5b 41 5c 41 5d 41 5e 41 5f 5d c3 48 8b 7b 28 e8 0d 44
RIP [<ffffffffbbbf1068>] free_msi_irqs+0x188/0x190
The solution is to not touch the adapter->state in iavf_watchdog_task()
and let the reset task handle the state transition.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97683c851f ]
The naming of the regulator is problematic. VCC is usually a supply
voltage whereas these devices have a separate VREF pin.
Secondly, the regulator core might have provided a stub regulator if
a real regulator wasn't provided. That would in turn have failed to
provide a voltage when queried. So reality was that there was no way
to use the internal reference.
In order to avoid breaking any dts out in the wild, make sure to fallback
to the original vcc naming if vref is not available.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210627163244.1090296-9-jic23@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4919ff59c ]
Currently, when userspace reads a datagram with a buffer that is
smaller than this datagram, the data will be truncated and only
part of it can be received by users. It doesn't seem right that
users don't know the datagram size and have to use a huge buffer
to read it to avoid the truncation.
This patch to fix it by keeping the skb in rcv queue until the
whole data is read by users. Only the last msg of the datagram
will be marked with MSG_EOR, just as TCP/SCTP does.
Note that this will work as above only when MSG_EOR is set in the
flags parameter of recvmsg(), so that it won't break any old user
applications.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14858dcc3b ]
Updating the current_state field of struct pci_dev the way it is done
in pci_enable_device_flags() before calling do_pci_enable_device() may
not work. For example, if the given PCI device depends on an ACPI
power resource whose _STA method initially returns 0 ("off"), but the
config space of the PCI device is accessible and the power state
retrieved from the PCI_PM_CTRL register is D0, the current_state
field in the struct pci_dev representing that device will get out of
sync with the power.state of its ACPI companion object and that will
lead to power management issues going forward.
To avoid such issues, make pci_enable_device_flags() call
pci_update_current_state() which takes ACPI device power management
into account, if present, to retrieve the current power state of the
device.
Link: https://lore.kernel.org/lkml/20210314000439.3138941-1-luzmaximilian@gmail.com/
Reported-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c445535c3e ]
Marking TSC as unstable has a side effect of marking sched_clock as
unstable when TSC is still being used as the sched_clock. This is not
desirable. Hyper-V ultimately uses a paravirtualized clock source that
provides a stable scheduler clock even on systems without TscInvariant
CPU capability. Hence, mark_tsc_unstable() call should be called _after_
scheduler clock has been changed to the paravirtualized clocksource. This
will prevent any unwanted manipulation of the sched_clock. Only TSC will
be correctly marked as unstable.
Signed-off-by: Ani Sinha <ani@anisinha.ca>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Tested-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20210713030522.1714803-1-ani@anisinha.ca
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97eb31384a ]
When loading a BPF program with a pinned map, the loader checks whether
the pinned map can be reused, i.e. their properties match. To derive
such of the pinned map, the loader invokes BPF_OBJ_GET_INFO_BY_FD and
then does the comparison.
Unfortunately, on < 4.12 kernels the BPF_OBJ_GET_INFO_BY_FD is not
available, so loading the program fails with the following error:
libbpf: failed to get map info for map FD 5: Invalid argument
libbpf: couldn't reuse pinned map at
'/sys/fs/bpf/tc/globals/cilium_call_policy': parameter
mismatch"
libbpf: map 'cilium_call_policy': error reusing pinned map
libbpf: map 'cilium_call_policy': failed to create:
Invalid argument(-22)
libbpf: failed to load object 'bpf_overlay.o'
To fix this, fallback to derivation of the map properties via
/proc/$PID/fdinfo/$MAP_FD if BPF_OBJ_GET_INFO_BY_FD fails with EINVAL,
which can be used as an indicator that the kernel doesn't support
the latter.
Signed-off-by: Martynas Pumputis <m@lambda.lt>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20210712125552.58705-1-m@lambda.lt
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8db11aebdb ]
The logic at dib8000_get_init_prbs() has a few issues:
1. the tables used there has an extra unused value at the beginning;
2. the dprintk() message doesn't write the right value when
transmission mode is not 8K;
3. the array overflow validation is done by the callers.
Rewrite the code to fix such issues.
This should also shut up those smatch warnings:
drivers/media/dvb-frontends/dib8000.c:2125 dib8000_get_init_prbs() error: buffer overflow 'lut_prbs_8k' 14 <= 14
drivers/media/dvb-frontends/dib8000.c:2129 dib8000_get_init_prbs() error: buffer overflow 'lut_prbs_2k' 14 <= 14
drivers/media/dvb-frontends/dib8000.c:2131 dib8000_get_init_prbs() error: buffer overflow 'lut_prbs_4k' 14 <= 14
drivers/media/dvb-frontends/dib8000.c:2134 dib8000_get_init_prbs() error: buffer overflow 'lut_prbs_8k' 14 <= 14
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1698ecb218 ]
Symptom is random switching of speakers when using multichannel.
Repeatedly running speakertest -c8 occasionally starts with
channels jumbled. This is fixed with HD_CTL_WHOLSMP.
The other bit looks beneficial and apears harmless in testing so
I'd suggest adding it too.
Documentation says: HD_CTL_WHILSMP_SET
Wait for whole sample. When this bit is set MAI transmit will start
only when there is at least one whole sample available in the fifo.
Documentation says: HD_CTL_CHALIGN_SET
Channel Align When Overflow. This bit is used to realign the audio
channels in case of an overflow.
If this bit is set, after the detection of an overflow, equal
amount of dummy words to the missing words will be written to fifo,
filling up the broken sample and maintaining alignment.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210525132354.297468-7-maxime@cerno.tech
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 22e5fe2a2a ]
userfaultfd assumes that the enabled features are set once and never
changed after UFFDIO_API ioctl succeeded.
However, currently, UFFDIO_API can be called concurrently from two
different threads, succeed on both threads and leave userfaultfd's
features in non-deterministic state. Theoretically, other uffd operations
(ioctl's and page-faults) can be dispatched while adversely affected by
such changes of features.
Moreover, the writes to ctx->state and ctx->features are not ordered,
which can - theoretically, again - let userfaultfd_ioctl() think that
userfaultfd API completed, while the features are still not initialized.
To avoid races, it is arguably best to get rid of ctx->state. Since there
are only 2 states, record the API initialization in ctx->features as the
uppermost bit and remove ctx->state.
Link: https://lkml.kernel.org/r/20210808020724.1022515-3-namit@vmware.com
Fixes: 9cd75c3cd4 ("userfaultfd: non-cooperative: add ability to report non-PF events from uffd descriptor")
Signed-off-by: Nadav Amit <namit@vmware.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Axel Rasmussen <axelrasmussen@google.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Peter Xu <peterx@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 52d83df682 ]
When CONFIG_TRIM_UNUSED_KSYMS is enabled, I see some warnings like this:
nm: arch/x86/entry/vdso/vdso32/note.o: no symbols
$NM (both GNU nm and llvm-nm) warns when no symbol is found in the
object. Suppress the stderr.
Fangrui Song mentioned binutils>=2.37 `nm -q` can be used to suppress
"no symbols" [1], and llvm-nm>=13.0.0 supports -q as well.
We cannot use it for now, but note it as a TODO.
[1]: https://sourceware.org/bugzilla/show_bug.cgi?id=27408
Fixes: bbda5ec671 ("kbuild: simplify dependency generation for CONFIG_TRIM_UNUSED_KSYMS")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bea6a94a27 ]
Starting with following patch MIPS Malta is not able to boot:
| commit 79edff1206
| Author: Rob Herring <robh@kernel.org>
| scripts/dtc: Update to upstream version v1.6.0-51-g183df9e9c2b9
The reason is the alignment test added to the fdt_ro_probe_(). To fix
this issue, we need to make sure that fdt_buf is aligned.
Since the dtc patch was designed to uncover potential issue, I handle
initial MIPS Malta patch as initial bug.
Fixes: e81a8c7dab ("MIPS: Malta: Setup RAM regions via DT")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9605f75cf3 ]
The prepare_compress_overwrite() gets/locks a page to prepare a read, and calls
f2fs_read_multi_pages() which checks EOF first. If there's any page beyond EOF,
we unlock the page and set cc->rpages[i] = NULL, which we can't put the page
anymore. This makes page leak, so let's fix by putting that page.
Fixes: a949dc5f2c ("f2fs: compress: fix race condition of overwrite vs truncate")
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 827f02842e ]
In f2fs_write_multi_pages(), f2fs_compress_pages() allocates pages for
compression work in cc->cpages[]. Then, f2fs_write_compressed_pages() initiates
bio submission. But, if there's any error before submitting the IOs like early
f2fs_cp_error(), previously it didn't free cpages by f2fs_compress_free_page().
Let's fix memory leak by putting that just before deallocating cc->cpages.
Fixes: 4c8ff7095b ("f2fs: support data compression")
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8dc3047c4 ]
We need to unmap pages from userspace process before removing pagecache
in punch_hole() like we did in f2fs_setattr().
Similar change:
commit 5e44f8c374 ("ext4: hole-punch use truncate_pagecache_range")
Fixes: fbfa2cc58d ("f2fs: add file operations")
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit adf9ea89c7 ]
In below path, it will return ENOENT if filesystem is shutdown:
- f2fs_map_blocks
- f2fs_get_dnode_of_data
- f2fs_get_node_page
- __get_node_page
- read_node_page
- is_sbi_flag_set(sbi, SBI_IS_SHUTDOWN)
return -ENOENT
- force return value from ENOENT to 0
It should be fine for read case, since it indicates a hole condition,
and caller could use .m_next_pgofs to skip the hole and continue the
lookup.
However it may cause confusing for write case, since leaving a hole
there, and said nothing was wrong doesn't help.
There is at least one case from dax_iomap_actor() will complain that,
so fix this in prior to supporting dax in f2fs.
xfstest generic/388 reports below warning:
ubuntu godown: xfstests-induced forced shutdown of /mnt/scratch_f2fs:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 485833 at fs/dax.c:1127 dax_iomap_actor+0x339/0x370
Call Trace:
iomap_apply+0x1c4/0x7b0
? dax_iomap_rw+0x1c0/0x1c0
dax_iomap_rw+0xad/0x1c0
? dax_iomap_rw+0x1c0/0x1c0
f2fs_file_write_iter+0x5ab/0x970 [f2fs]
do_iter_readv_writev+0x273/0x2e0
do_iter_write+0xab/0x1f0
vfs_iter_write+0x21/0x40
iter_file_splice_write+0x287/0x540
do_splice+0x37c/0xa60
__x64_sys_splice+0x15f/0x3a0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
ubuntu godown: xfstests-induced forced shutdown of /mnt/scratch_f2fs:
------------[ cut here ]------------
RIP: 0010:dax_iomap_pte_fault.isra.0+0x72e/0x14a0
Call Trace:
dax_iomap_fault+0x44/0x70
f2fs_dax_huge_fault+0x155/0x400 [f2fs]
f2fs_dax_fault+0x18/0x30 [f2fs]
__do_fault+0x4e/0x120
do_fault+0x3cf/0x7a0
__handle_mm_fault+0xa8c/0xf20
? find_held_lock+0x39/0xd0
handle_mm_fault+0x1b6/0x480
do_user_addr_fault+0x320/0xcd0
? rcu_read_lock_sched_held+0x67/0xc0
exc_page_fault+0x77/0x3f0
? asm_exc_page_fault+0x8/0x30
asm_exc_page_fault+0x1e/0x30
Fixes: 83a3bfdb5a ("f2fs: indicate shutdown f2fs to allow unmount successfully")
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad126ebdde ]
There is a missing place we forgot to account .skipped_gc_rwsem, fix it.
Fixes: 6f8d445506 ("f2fs: avoid fi->i_gc_rwsem[WRITE] lock in f2fs_gc")
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d78dfde33 ]
Since commit e1a1ef84cd ("KVM: PPC: Book3S: Allocate guest TCEs on
demand too"), pages for TCE tables for KVM guests are allocated only
when needed. This allows skipping any update when clearing TCEs. This
works mostly fine as TCE updates are handled when the MMU is enabled.
The realmode handlers fail with H_TOO_HARD when pages are not yet
allocated, except when clearing a TCE in which case KVM prints a warning
and proceeds to dereference a NULL pointer, which crashes the host OS.
This has not been caught so far as the change in commit e1a1ef84cd is
reasonably new, and POWER9 runs mostly radix which does not use realmode
handlers. With hash, the default TCE table is memset() by QEMU when the
machine is reset which triggers page faults and the KVM TCE device's
kvm_spapr_tce_fault() handles those with MMU on. And the huge DMA
windows are not cleared by VMs which instead successfully create a DMA
window big enough to map the VM memory 1:1 and then VMs just map
everything without clearing.
This started crashing now as commit 381ceda88c ("powerpc/pseries/iommu:
Make use of DDW for indirect mapping") added a mode when a dymanic DMA
window not big enough to map the VM memory 1:1 but it is used anyway,
and the VM now is the first (i.e. not QEMU) to clear a just created
table. Note that upstream QEMU needs to be modified to trigger the VM to
trigger the host OS crash.
This replaces WARN_ON_ONCE_RM() with a check and return, and adds
another warning if TCE is not being cleared.
Fixes: e1a1ef84cd ("KVM: PPC: Book3S: Allocate guest TCEs on demand too")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210827040706.517652-1-aik@ozlabs.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35b72573e9 ]
The current hash algorithm used for hashing cookie keys is really bad,
producing almost no dispersion (after a test kernel build, ~30000 files
were split over just 18 out of the 32768 hash buckets).
Borrow the full_name_hash() hash function into fscache to do the hashing
for cookie keys and, in the future, volume keys.
I don't want to use full_name_hash() as-is because I want the hash value to
be consistent across arches and over time as the hash value produced may
get used on disk.
I can also optimise parts of it away as the key will always be a padded
array of aligned 32-bit words.
Fixes: ec0328e46d ("fscache: Maintain a catalogue of allocated cookies")
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
cc: linux-cachefs@redhat.com
Link: https://lore.kernel.org/r/162431201844.2908479.8293647220901514696.stgit@warthog.procyon.org.uk/
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8b9280303 ]
lscpu() uses core_siblings to list the number of sockets in the
system. core_siblings is set using topology_core_cpumask.
While optimizing the powerpc bootup path, Commit 4ca234a9cb
("powerpc/smp: Stop updating cpu_core_mask"). it was found that
updating cpu_core_mask() ended up taking a lot of time. It was thought
that on Powerpc, cpu_core_mask() would always be same as
cpu_cpu_mask() i.e number of sockets will always be equal to number of
nodes. As an optimization, cpu_core_mask() was made a snapshot of
cpu_cpu_mask().
However that was found to be false with PowerPc KVM guests, where each
node could have more than one socket. So with Commit c47f892d7a
("powerpc/smp: Reintroduce cpu_core_mask"), cpu_core_mask was updated
based on chip_id but in an optimized way using some mask manipulations
and chip_id caching.
However on non-PowerNV and non-pseries KVM guests (i.e not
implementing cpu_to_chip_id(), continued to use a copy of
cpu_cpu_mask().
There are two issues that were noticed on such systems
1. lscpu would report one extra socket.
On a IBM,9009-42A (aka zz system) which has only 2 chips/ sockets/
nodes, lscpu would report
Architecture: ppc64le
Byte Order: Little Endian
CPU(s): 160
On-line CPU(s) list: 0-159
Thread(s) per core: 8
Core(s) per socket: 6
Socket(s): 3 <--------------
NUMA node(s): 2
Model: 2.2 (pvr 004e 0202)
Model name: POWER9 (architected), altivec supported
Hypervisor vendor: pHyp
Virtualization type: para
L1d cache: 32K
L1i cache: 32K
L2 cache: 512K
L3 cache: 10240K
NUMA node0 CPU(s): 0-79
NUMA node1 CPU(s): 80-159
2. Currently cpu_cpu_mask is updated when a core is
added/removed. However its not updated when smt mode switching or on
CPUs are explicitly offlined. However all other percpu masks are
updated to ensure only active/online CPUs are in the masks.
This results in build_sched_domain traces since there will be CPUs in
cpu_cpu_mask() but those CPUs are not present in SMT / CACHE / MC /
NUMA domains. A loop of threads running smt mode switching and core
add/remove will soon show this trace.
Hence cpu_cpu_mask has to be update at smt mode switch.
This will have impact on cpu_core_mask(). cpu_core_mask() is a
snapshot of cpu_cpu_mask. Different CPUs within the same socket will
end up having different cpu_core_masks since they are snapshots at
different points of time. This means when lscpu will start reporting
many more sockets than the actual number of sockets/ nodes / chips.
Different ways to handle this problem:
A. Update the snapshot aka cpu_core_mask for all CPUs whenever
cpu_cpu_mask is updated. This would a non-optimal solution.
B. Instead of a cpumask_var_t, make cpu_core_map a cpumask pointer
pointing to cpu_cpu_mask. However percpu cpumask pointer is frowned
upon and we need a clean way to handle PowerPc KVM guest which is
not a snapshot.
C. Update cpu_core_masks all PowerPc systems like in PowerPc KVM
guests using mask manipulations. This approach is relatively simple
and unifies with the existing code.
D. On top of 3, we could also resurrect get_physical_package_id which
could return a nid for the said CPU. However this is not needed at this
time.
Option C is the preferred approach for now.
While this is somewhat a revert of Commit 4ca234a9cb ("powerpc/smp:
Stop updating cpu_core_mask").
1. Plain revert has some conflicts
2. For chip_id == -1, the cpu_core_mask is made identical to
cpu_cpu_mask, unlike previously where cpu_core_mask was set to a core
if chip_id doesn't exist.
This goes by the principle that if chip_id is not exposed, then
sockets / chip / node share the same set of CPUs.
With the fix, lscpu o/p would be
Architecture: ppc64le
Byte Order: Little Endian
CPU(s): 160
On-line CPU(s) list: 0-159
Thread(s) per core: 8
Core(s) per socket: 6
Socket(s): 2 <--------------
NUMA node(s): 2
Model: 2.2 (pvr 004e 0202)
Model name: POWER9 (architected), altivec supported
Hypervisor vendor: pHyp
Virtualization type: para
L1d cache: 32K
L1i cache: 32K
L2 cache: 512K
L3 cache: 10240K
NUMA node0 CPU(s): 0-79
NUMA node1 CPU(s): 80-159
Fixes: 4ca234a9cb ("powerpc/smp: Stop updating cpu_core_mask")
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210826100401.412519-3-srikar@linux.vnet.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1782663897 ]
After the L1 saves its PMU SPRs but before loading the L2's PMU SPRs,
switch the pmcregs_in_use field in the L1 lppaca to the value advertised
by the L2 in its VPA. On the way out of the L2, set it back after saving
the L2 PMU registers (if they were in-use).
This transfers the PMU liveness indication between the L1 and L2 at the
points where the registers are not live.
This fixes the nested HV bug for which a workaround was added to the L0
HV by commit 63279eeb7f ("KVM: PPC: Book3S HV: Always save guest pmu
for guest capable of nesting"), which explains the problem in detail.
That workaround is no longer required for guests that include this bug
fix.
Fixes: 360cae3137 ("KVM: PPC: Book3S HV: Nested guest entry via hypercall")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Link: https://lore.kernel.org/r/20210811160134.904987-10-npiggin@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 313bf281f2 ]
clk_get_rate() returns unsigned long and currently this driver stores the
return value in u32 type, resulting the below warning:
Fixed smatch warnings:
drivers/scsi/ufs/ufs-exynos.c:286 exynos_ufs_get_clk_info()
warn: wrong type for 'ufs->mclk_rate' (should be 'ulong')
drivers/scsi/ufs/ufs-exynos.c:287 exynos_ufs_get_clk_info()
warn: wrong type for 'pclk_rate' (should be 'ulong')
Link: https://lore.kernel.org/r/20210819171131.55912-1-alim.akhtar@samsung.com
Fixes: 55f4b1f736 ("scsi: ufs: ufs-exynos: Add UFS host support for Exynos SoCs")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d7d6dac8f ]
The __kvmhv_copy_tofrom_guest_radix function was introduced along with
nested HV guest support. It uses the platform's Radix MMU quadrants to
provide a nested hypervisor with fast access to its nested guests
memory (H_COPY_TOFROM_GUEST hypercall). It has also since been added
as a fast path for the kvmppc_ld/st routines which are used during
instruction emulation.
The commit def0bfdbd6 ("powerpc: use probe_user_read() and
probe_user_write()") changed the low level copy function from
raw_copy_from_user to probe_user_read, which adds a check to
access_ok. In powerpc that is:
static inline bool __access_ok(unsigned long addr, unsigned long size)
{
return addr < TASK_SIZE_MAX && size <= TASK_SIZE_MAX - addr;
}
and TASK_SIZE_MAX is 0x0010000000000000UL for 64-bit, which means that
setting the two MSBs of the effective address (which correspond to the
quadrant) now cause access_ok to reject the access.
This was not caught earlier because the most common code path via
kvmppc_ld/st contains a fallback (kvm_read_guest) that is likely to
succeed for L1 guests. For nested guests there is no fallback.
Another issue is that probe_user_read (now __copy_from_user_nofault)
does not return the number of bytes not copied in case of failure, so
the destination memory is not being cleared anymore in
kvmhv_copy_from_guest_radix:
ret = kvmhv_copy_tofrom_guest_radix(vcpu, eaddr, to, NULL, n);
if (ret > 0) <-- always false!
memset(to + (n - ret), 0, ret);
This patch fixes both issues by skipping access_ok and open-coding the
low level __copy_to/from_user_inatomic.
Fixes: def0bfdbd6 ("powerpc: use probe_user_read() and probe_user_write()")
Signed-off-by: Fabiano Rosas <farosas@linux.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210805212616.2641017-2-farosas@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d36207b848 ]
On the i.MX8M*, the TF-A exposes a SiP (Silicon Provider) service
for DDR frequency scaling. The imx8m-ddrc-devfreq driver calls the
SiP and then does clk_set_parent on the DDR muxes to synchronize
the clock tree.
Since 936c383673 ("clk: imx: fix composite peripheral flags"),
these TF-A managed muxes have SET_PARENT_GATE set, which results
in imx8m-ddrc-devfreq's clk_set_parent after SiP failing with -EBUSY:
echo 25000000 > userspace/set_freq
imx8m-ddrc-devfreq 3d400000.memory-controller: failed to set
dram_apb parent: -16
Fix this by adding a new i.MX composite flag for firmware managed
clocks, which clears SET_PARENT_GATE.
This is safe to do, because updating the Linux clock tree to reflect
reality will always be glitch-free.
Fixes: 936c383673 ("clk: imx: fix composite peripheral flags")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20210810151432.9228-1-a.fatoum@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 786537063b ]
A quirk was recently added for Elan devices that has same device match
as an entry earlier in the list. The i2c_hid_lookup_quirk function will
always return the last match in the list, so the new entry shadows the
old entry. The quirk in the previous entry, I2C_HID_QUIRK_BOGUS_IRQ,
silenced a flood of messages which have reappeared in the 5.13 kernel.
This change moves the two quirk flags into the same entry.
Fixes: ca66a6770b (HID: i2c-hid: Skip ELAN power-on command after reset)
Signed-off-by: Jim Broadus <jbroadus@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d0e28a6145 ]
CONFIG_MTD_PHYSMAP_OF is not longer enabled as it depends on
MTD_PHYSMAP which is not enabled.
This is a regression from commit 642b1e8dbe ("mtd: maps: Merge
physmap_of.c into physmap-core.c"), which added the extra dependency.
Add CONFIG_MTD_PHYSMAP=y so this stays in the config, as Christophe said
it is useful for build coverage.
Fixes: 642b1e8dbe ("mtd: maps: Merge physmap_of.c into physmap-core.c")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Acked-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210817045407.2445664-3-joel@jms.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ccc89737aa ]
This driver has some left over "return 1" on failure style code mixed with
"return negative error codes" style code. The caller doesn't care so we
should just convert everything to return negative error codes.
Then there was a problem that there were two variables used to store error
codes which just resulted in confusion. If qedf_alloc_bdq() returned a
negative error code, we accidentally returned success instead of
propagating the error code. So get rid of the "rc" variable and use
"status" every where.
Also remove the "status = 0" initialization so that these sorts of bugs
will be detected by the compiler in the future.
Link: https://lore.kernel.org/r/20210810085023.GA23998@kili
Fixes: 61d8658b4a ("scsi: qedf: Add QLogic FastLinQ offload FCoE driver framework.")
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4dbe57d46d ]
This function had some left over code that returned 1 on error instead
negative error codes. Convert everything to use negative error codes. The
caller treats all non-zero returns the same so this does not affect run
time.
A couple places set "rc" instead of "status" so those error paths ended up
returning success by mistake. Get rid of the "rc" variable and use
"status" everywhere.
Remove the bogus "status = 0" initialization, as a future proofing measure
so the compiler will warn about uninitialized error codes.
Link: https://lore.kernel.org/r/20210810084753.GD23810@kili
Fixes: ace7f46ba5 ("scsi: qedi: Add QLogic FastLinQ offload iSCSI driver framework.")
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c7248bb8d ]
When a LPAR is migratable, we should consider the maximum possible NUMA
node instead of the number of NUMA nodes from the actual system.
The DT property 'ibm,current-associativity-domains' defines the maximum
number of nodes the LPAR can see when running on that box. But if the
LPAR is being migrated on another box, it may see up to the nodes
defined by 'ibm,max-associativity-domains'. So if a LPAR is migratable,
that value should be used.
Unfortunately, there is no easy way to know if an LPAR is migratable or
not. The hypervisor exports the property 'ibm,migratable-partition' in
the case it set to migrate partition, but that would not mean that the
current partition is migratable.
Without this patch, when a LPAR is started on a 2 node box and then
migrated to a 3 node box, the hypervisor may spread the LPAR's CPUs on
the 3rd node. In that case if a CPU from that 3rd node is added to the
LPAR, it will be wrongly assigned to the node because the kernel has
been set to use up to 2 nodes (the configuration of the departure node).
With this patch applies, the CPU is correctly added to the 3rd node.
Fixes: f9f130ff2e ("powerpc/numa: Detect support for coregroup")
Signed-off-by: Laurent Dufour <ldufour@linux.ibm.com>
Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210511073136.17795-1-ldufour@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d46dd04cb ]
Since bc1c56e9bb transport->srcport may by unset, causing
get_srcport() to return 0 when called. Fix this by querying the port
from the underlying socket instead of the transport.
Fixes: bc1c56e9bb (SUNRPC: prevent port reuse on transports which don't request it)
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f99fa50880 ]
The xprtrdma client code currently relies on the task that initiated the
connect to hold the XPRT_LOCK for the duration of the connection
attempt. If the task is woken early, due to some other event, then that
lock could get released early.
Avoid races by using the same mechanism that the socket code uses of
transferring lock ownership to the RDMA connect worker itself. That
frees us to call rpcrdma_xprt_disconnect() directly since we're now
guaranteed exclusion w.r.t. other callers.
Fixes: 4cf44be6f1 ("xprtrdma: Fix recursion into rpcrdma_xprt_disconnect()")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2dc3e5fad ]
We really should not call rpc_wake_up_queued_task_set_status() with
xprt->snd_task as an argument unless we are certain that is actually an
rpc_task.
Fixes: 0445f92c5d ("SUNRPC: Fix disconnection races")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6236a98b3 ]
The intention of the layout barrier is to ensure that we do not update
the layout to match an older value than the current expectation. Fix the
test in pnfs_layout_stateid_blocked() to reflect that it is legal for
the seqid of the stateid to match that of the barrier.
Fixes: aa95edf309 ("NFSv4/pnfs: Fix the layout barrier update")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45baadaad7 ]
A zero value for the layout barrier indicates that it has been cleared
(since seqid '0' is an illegal value), so we should always allow it to
be updated.
Fixes: d29b468da4 ("pNFS/NFSv4: Improve rejection of out-of-order layouts")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e20772cbdf ]
If NFS_LAYOUT_RETURN_REQUESTED is set, but there is no value set for
the layout plh_return_seq, we can end up in a livelock loop in which
every layout segment retrieved by a new call to layoutget is immediately
invalidated by pnfs_layout_need_return().
To get around this, we should just set plh_return_seq to the current
value of the layout stateid's seqid.
Fixes: d474f96104 ("NFS: Don't return layout segments that are in use")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 173735c346 ]
Due to link order, dma_debug_init is called before debugfs has a chance
to initialize (via debugfs_init which also happens in the core initcall
stage), so the directories for dma-debug are never created.
Decouple dma_debug_fs_init from dma_debug_init and defer its init until
core_initcall_sync (after debugfs has been initialized) while letting
dma-debug initialization occur as soon as possible to catch any early
mappings, as suggested in [1].
[1] https://lore.kernel.org/linux-iommu/YIgGa6yF%2Fadg8OSN@kroah.com/
Fixes: 15b28bbcd5 ("dma-debug: move initialization to common code")
Signed-off-by: Anthony Iliopoulos <ailiop@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 946e1052cd ]
Don't call printk() when CONFIG_PRINTK is not set.
Fixes the following build errors:
or1k-linux-ld: arch/openrisc/kernel/entry.o: in function `_external_irq_handler':
(.text+0x804): undefined reference to `printk'
(.text+0x804): relocation truncated to fit: R_OR1K_INSN_REL_26 against undefined symbol `printk'
Fixes: 9d02a4283e ("OpenRISC: Boot code")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Cc: Stafford Horne <shorne@gmail.com>
Cc: openrisc@lists.librecores.org
Signed-off-by: Stafford Horne <shorne@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d4bf15a7ce ]
I recently found a case where de->name_len is 0 in f2fs_fill_dentries()
easily reproduced, and finally set the fsck flag.
Thread A Thread B
- f2fs_readdir
- f2fs_read_inline_dir
- ctx->pos = d.max
- f2fs_add_dentry
- f2fs_add_inline_entry
- do_convert_inline_dir
- f2fs_add_regular_entry
- f2fs_readdir
- f2fs_fill_dentries
- set_sbi_flag(sbi, SBI_NEED_FSCK)
Process A opens the folder, and has been reading without closing it.
During this period, Process B created a file under the folder (occupying
multiple f2fs_dir_entry, exceeding the d.max of the inline dir). After
creation, process A uses the d.max of inline dir to read it again, and
it will read that de->name_len is 0.
And Chao pointed out that w/o inline conversion, the race condition still
can happen as below:
dir_entry1: A
dir_entry2: B
dir_entry3: C
free slot: _
ctx->pos: ^
Thread A is traversing directory,
ctx-pos moves to below position after readdir() by thread A:
AAAABBBB___
^
Then thread B delete dir_entry2, and create dir_entry3.
Thread A calls readdir() to lookup dirents starting from middle
of new dirent slots as below:
AAAACCCCCC_
^
In these scenarios, the file system is not damaged, and it's hard to
avoid it. But we can bypass tagging FSCK flag if:
a) bit_pos (:= ctx->pos % d->max) is non-zero and
b) before bit_pos moves to first valid dir_entry.
Fixes: ddf06b753a ("f2fs: fix to trigger fsck if dirent.name_len is zero")
Signed-off-by: Yangtao Li <frank.li@vivo.com>
[Chao: clean up description]
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d04691d373 ]
After commit 7cbd631d4dec ("cpuidle: pseries: Fixup CEDE0 latency only
for POWER10 onwards"), pseries_idle_probe() is no longer inlined when
compiling with clang, which causes a modpost warning:
WARNING: modpost: vmlinux.o(.text+0xc86a54): Section mismatch in
reference from the function pseries_idle_probe() to the function
.init.text:fixup_cede0_latency()
The function pseries_idle_probe() references
the function __init fixup_cede0_latency().
This is often because pseries_idle_probe lacks a __init
annotation or the annotation of fixup_cede0_latency is wrong.
pseries_idle_probe() is a non-init function, which calls
fixup_cede0_latency(), which is an init function, explaining the
mismatch. pseries_idle_probe() is only called from
pseries_processor_idle_init(), which is an init function, so mark
pseries_idle_probe() as __init so there is no more warning.
Fixes: 054e44ba99 ("cpuidle: pseries: Add function to parse extended CEDE records")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210803211547.1093820-1-nathan@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6cae77f1b ]
commit 7c6986ade6 ("powerpc/stacktrace: Fix spurious "stale" traces in raise_backtrace_ipi()")
introduces udelay() call without including the linux/delay.h header.
This may happen to work on master but the header that declares the
functionshould be included nonetheless.
Fixes: 7c6986ade6 ("powerpc/stacktrace: Fix spurious "stale" traces in raise_backtrace_ipi()")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210729180103.15578-1-msuchanek@suse.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50741b70b0 ]
Commit d947fb4c96 ("cpuidle: pseries: Fixup exit latency for
CEDE(0)") sets the exit latency of CEDE(0) based on the latency values
of the Extended CEDE states advertised by the platform
On POWER9 LPARs, the firmwares advertise a very low value of 2us for
CEDE1 exit latency on a Dedicated LPAR. The latency advertized by the
PHYP hypervisor corresponds to the latency required to wakeup from the
underlying hardware idle state. However the wakeup latency from the
LPAR perspective should include
1. The time taken to transition the CPU from the Hypervisor into the
LPAR post wakeup from platform idle state
2. Time taken to send the IPI from the source CPU (waker) to the idle
target CPU (wakee).
1. can be measured via timer idle test, where we queue a timer, say
for 1ms, and enter the CEDE state. When the timer fires, in the timer
handler we compute how much extra timer over the expected 1ms have we
consumed. On a a POWER9 LPAR the numbers are
CEDE latency measured using a timer (numbers in ns)
N Min Median Avg 90%ile 99%ile Max Stddev
400 2601 5677 5668.74 5917 6413 9299 455.01
1. and 2. combined can be determined by an IPI latency test where we
send an IPI to an idle CPU and in the handler compute the time
difference between when the IPI was sent and when the handler ran. We
see the following numbers on POWER9 LPAR.
CEDE latency measured using an IPI (numbers in ns)
N Min Median Avg 90%ile 99%ile Max Stddev
400 711 7564 7369.43 8559 9514 9698 1200.01
Suppose, we consider the 99th percentile latency value measured using
the IPI to be the wakeup latency, the value would be 9.5us This is in
the ballpark of the default value of 10us.
Hence, use the exit latency of CEDE(0) based on the latency values
advertized by platform only from POWER10 onwards. The values
advertized on POWER10 platforms is more realistic and informed by the
latency measurements. For earlier platforms stick to the default value
of 10us. The fix was suggested by Michael Ellerman.
Fixes: d947fb4c96 ("cpuidle: pseries: Fixup exit latency for CEDE(0)")
Reported-by: Enrico Joedecke <joedecke@de.ibm.com>
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1626676399-15975-2-git-send-email-ego@linux.vnet.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62004871e1 ]
It is possible for the primary IPoIB network device associated with any
RDMA device to fail to join certain multicast groups preventing IPv6
neighbor discovery and possibly other network ULPs from working
correctly. The IPv4 broadcast group is not affected as the IPoIB network
device handles joining that multicast group directly.
This is because the primary IPoIB network device uses the pkey at ndex 0
in the associated RDMA device's pkey table. Anytime the pkey value of
index 0 changes, the primary IPoIB network device automatically modifies
it's broadcast address (i.e. /sys/class/net/[ib0]/broadcast), since the
broadcast address includes the pkey value, and then bounces carrier. This
includes initial pkey assignment, such as when the pkey at index 0
transitions from the opa default of invalid (0x0000) to some value such as
the OPA default pkey for Virtual Fabric 0: 0x8001 or when the fabric
manager is restarted with a configuration change causing the pkey at index
0 to change. Many network ULPs are not sensitive to the carrier bounce and
are not expecting the broadcast address to change including the linux IPv6
stack. This problem does not affect IPoIB child network devices as their
pkey value is constant for all time.
To mitigate this issue, change the default pkey in at index 0 to 0x8001 to
cover the predominant case and avoid issues as ipoib comes up and the FM
sweeps.
At some point, ipoib multicast support should automatically fix
non-broadcast addresses as it does with the primary broadcast address.
Fixes: 7724105686 ("IB/hfi1: add driver files")
Link: https://lore.kernel.org/r/20210715160445.142451.47651.stgit@awfm-01.cornelisnetworks.com
Suggested-by: Josh Collier <josh.d.collier@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6fffe52fb3 ]
The rk3036/rk3328 pll types were converted to checking the lock status
via the internal register in january 2020, so don't need the grf
reference since then.
But it was forgotten to remove grf check when deciding between the
pll rate ops (read-only vs. read-write), so a clock driver without
the needed grf reference might've been put into the read-only mode
just because the grf reference was missing.
This affected the rk356x that needs to reclock certain plls at boot.
Fix this by removing the check for the grf for selecting the utilized
operations.
Suggested-by: Heiko Stuebner <heiko@sntech.de>
Fixes: 7f6ffbb885 ("clk: rockchip: convert rk3036 pll type to use internal lock status")
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
[adjusted the commit message, adjusted the fixes tag]
Link: https://lore.kernel.org/r/20210728180034.717953-3-pgwipeout@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit baf8d6899b ]
The PWM pins on North Bridge on Armada 37xx can be configured into PWM
or GPIO functions. When in PWM function, each pin can also be configured
to drive low on 0 and tri-state on 1 (LED mode).
The current definitions handle this by declaring two pin groups for each
pin:
- group "pwmN" with functions "pwm" and "gpio"
- group "ledN_od" ("od" for open drain) with functions "led" and "gpio"
This is semantically incorrect. The correct definition for each pin
should be one group with three functions: "pwm", "led" and "gpio".
Change the "pwmN" groups to support "led" function.
Remove "ledN_od" groups. This cannot break backwards compatibility with
older device trees: no device tree uses it since there is no PWM driver
for this SOC yet. Also "ledN_od" groups are not even documented.
Fixes: b835d69530 ("pinctrl: armada-37xx: swap polarity on LED group")
Signed-off-by: Marek Behún <kabel@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210719112938.27594-1-kabel@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4abaa9eeb ]
The power supply states of discharging, charging, full, etc, represent
state of charging, not the capacity level of the battery (for which
we have a separate property). Current HID usage tables to not allow
for expressing charging state of the batteries found in generic
styli, so we should simply assume that the battery is discharging
even if current capacity is at 100% when battery strength reporting
is done via HID interface. In fact, we were doing just that before
commit 581c448476.
This change helps UIs to not mis-represent fully charged batteries in
styli as being charging/topping-off.
Fixes: 581c448476 ("HID: input: map digitizer battery usage")
Reported-by: Kenneth Albanowski <kenalba@google.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fcb461e2bc upstream.
There is an issue that when PCIe switch is connected to an Armada 3700
board, there will be lots of warnings about PIO errors when reading the
config space. According to Aardvark PIO read and write sequence in HW
specification, the current way to check PIO status has the following
issues:
1) For PIO read operation, it reports the error message, which should be
avoided according to HW specification.
2) For PIO read and write operations, it only checks PIO operation complete
status, which is not enough, and error status should also be checked.
This patch aligns the code with Aardvark PIO read and write sequence in HW
specification on PIO status check and fix the warnings when reading config
space.
[pali: Fix CRS handling when CRSSVE is not enabled]
Link: https://lore.kernel.org/r/20210722144041.12661-2-pali@kernel.org
Tested-by: Victor Gu <xigu@marvell.com>
Signed-off-by: Evan Wang <xswang@marvell.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Victor Gu <xigu@marvell.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org # b1bd571447 ("PCI: aardvark: Indicate error in 'val' when config read fails")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 64f160e19e upstream.
In commit 6df6ba974a ("PCI: aardvark: Remove PCIe outbound window
configuration") was removed aardvark PCIe outbound window configuration and
commit description said that was recommended solution by HW designers.
But that commit completely removed support for configuring PCIe IO
resources without removing PCIe IO 'ranges' from DTS files. After that
commit PCIe IO space started to be treated as PCIe MEM space and accessing
it just caused kernel crash.
Moreover implementation of PCIe outbound windows prior that commit was
incorrect. It completely ignored offset between CPU address and PCIe bus
address and expected that in DTS is CPU address always same as PCIe bus
address without doing any checks. Also it completely ignored size of every
PCIe resource specified in 'ranges' DTS property and expected that every
PCIe resource has size 128 MB (also for PCIe IO range). Again without any
check. Apparently none of PCIe resource has in DTS specified size of 128
MB. So it was completely broken and thanks to how aardvark mask works,
configuration was completely ignored.
This patch reverts back support for PCIe outbound window configuration but
implementation is a new without issues mentioned above. PCIe outbound
window is required when DTS specify in 'ranges' property non-zero offset
between CPU and PCIe address space. To address recommendation by HW
designers as specified in commit description of 6df6ba974a, set default
outbound parameters as PCIe MEM access without translation and therefore
for this PCIe 'ranges' it is not needed to configure PCIe outbound window.
For PCIe IO space is needed to configure aardvark PCIe outbound window.
This patch fixes kernel crash when trying to access PCIe IO space.
Link: https://lore.kernel.org/r/20210624215546.4015-2-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # 6df6ba974a ("PCI: aardvark: Remove PCIe outbound window configuration")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8bd29bd49 upstream.
The pciconfig_read() syscall reads PCI configuration space using
hardware-dependent config accessors.
If the read fails on PCI, most accessors don't return an error; they
pretend the read was successful and got ~0 data from the device, so the
syscall returns success with ~0 data in the buffer.
When the accessor does return an error, pciconfig_read() normally fills the
user's buffer with ~0 and returns an error in errno. But after
e4585da22a ("pci syscall.c: Switch to refcounting API"), we don't fill
the buffer with ~0 for the EPERM "user lacks CAP_SYS_ADMIN" error.
Userspace may rely on the ~0 data to detect errors, but after e4585da22a,
that would not detect CAP_SYS_ADMIN errors.
Restore the original behaviour of filling the buffer with ~0 when the
CAP_SYS_ADMIN check fails.
[bhelgaas: commit log, fold in Nathan's fix
https://lore.kernel.org/r/20210803200836.500658-1-nathan@kernel.org]
Fixes: e4585da22a ("pci syscall.c: Switch to refcounting API")
Link: https://lore.kernel.org/r/20210729233755.1509616-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 00823dcbdd upstream.
Previously we assumed that all Root Ports and Switch Downstream Ports
supported Link Bandwidth Notification. Per spec, this is only required
for Ports supporting Links wider than x1 and/or multiple Link speeds
(PCIe r5.0, sec 7.5.3.6).
Because we assumed all Ports supported it, we tried to set up a Bandwidth
Notification IRQ, which failed for devices that don't support IRQs at all,
which meant pcieport didn't attach to the Port at all.
Check the Link Bandwidth Notification Capability bit and enable the service
only when the Port supports it.
[bhelgaas: commit log]
Fixes: e8303bb7a7 ("PCI/LINK: Report degraded links via link bandwidth notification")
Link: https://lore.kernel.org/r/20210512213314.7778-1-stuart.w.hayes@gmail.com
Signed-off-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 65ddf65648 upstream.
This patch fixes below problems of sb/cp sanity check:
- in sanity_check_raw_superi(), it missed to consider log header
blocks while cp_payload check.
- in f2fs_sanity_check_ckpt(), it missed to check nat_bits_blocks.
Cc: <stable@kernel.org>
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b30d0289de upstream.
The merge_fdt_bootargs() function by definition consumes more than 1024
bytes of stack because it has a 1024 byte command line on the stack,
meaning that we always get a warning when building this file:
arch/arm/boot/compressed/atags_to_fdt.c: In function 'merge_fdt_bootargs':
arch/arm/boot/compressed/atags_to_fdt.c:98:1: warning: the frame size of 1032 bytes is larger than 1024 bytes [-Wframe-larger-than=]
However, as this is the decompressor and we know that it has a very shallow
call chain, and we do not actually risk overflowing the kernel stack
at runtime here.
This just shuts up the warning by disabling the warning flag for this
file.
Tested on Nexus 7 2012 builds.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a6430ab9c upstream.
Commit ca6bfcb2f6 ("libata: Enable queued TRIM for Samsung SSD 860")
limited the existing ATA_HORKAGE_NO_NCQ_TRIM quirk from "Samsung SSD 8*",
covering all Samsung 800 series SSDs, to only apply to "Samsung SSD 840*"
and "Samsung SSD 850*" series based on information from Samsung.
But there is a large number of users which is still reporting issues
with the Samsung 860 and 870 SSDs combined with Intel, ASmedia or
Marvell SATA controllers and all reporters also report these problems
going away when disabling queued trims.
Note that with AMD SATA controllers users are reporting even worse
issues and only completely disabling NCQ helps there, this will be
addressed in a separate patch.
Fixes: ca6bfcb2f6 ("libata: Enable queued TRIM for Samsung SSD 860")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=203475
Cc: stable@vger.kernel.org
Cc: Kate Hsuan <hpa@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20210823095220.30157-1-hdegoede@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c1dc8bda3 upstream.
When the ESTABLISH ccw does not complete within the specified timeout,
try our best to cancel the ccw program that is still active on the
device. Otherwise the IO subsystem might be accessing it even after
the driver eg. called qdio_free().
Fixes: 779e6e1c72 ("[S390] qdio: new qdio driver.")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Cc: <stable@vger.kernel.org> # 2.6.27
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c197870e4 upstream.
When qdio_establish() times out while waiting for the ESTABLISH ccw to
complete, it calls qdio_shutdown() to roll back all of its previous
actions. But at this point the qdio_irq's state is still
QDIO_IRQ_STATE_INACTIVE, so qdio_shutdown() will exit immediately
without doing any actual work.
Which means that eg. the qdio_irq's thinint-indicator stays registered,
and cdev->handler isn't restored to its old value. And since
commit 954d6235be ("s390/qdio: make thinint registration symmetric")
the qdio_irq also stays on the tiq_list, so on the next qdio_establish()
we might get a helpful BUG from the list-debugging code:
...
[ 4633.512591] list_add double add: new=00000000005a4110, prev=00000001b357db78, next=00000000005a4110.
[ 4633.512621] ------------[ cut here ]------------
[ 4633.512623] kernel BUG at lib/list_debug.c:29!
...
[ 4633.512796] [<00000001b2c6ee9a>] __list_add_valid+0x82/0xa0
[ 4633.512798] ([<00000001b2c6ee96>] __list_add_valid+0x7e/0xa0)
[ 4633.512800] [<00000001b2fcecce>] qdio_establish_thinint+0x116/0x190
[ 4633.512805] [<00000001b2fcbe58>] qdio_establish+0x128/0x498
...
Fix this by extracting a goto-chain from the existing error exits in
qdio_establish(), and check the return value of the wait_event_...()
to detect the timeout condition.
Fixes: 779e6e1c72 ("[S390] qdio: new qdio driver.")
Root-caused-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Cc: <stable@vger.kernel.org> # 2.6.27
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a10d7fdb6 upstream.
As warned by smatch:
drivers/media/usb/uvc/uvc_v4l2.c:911 uvc_ioctl_g_input() error: doing dma on the stack (&i)
drivers/media/usb/uvc/uvc_v4l2.c:943 uvc_ioctl_s_input() error: doing dma on the stack (&i)
those two functions call uvc_query_ctrl passing a pointer to
a data at the DMA stack. those are used to send URBs via
usb_control_msg(). Using DMA stack is not supported and should
not work anymore on modern Linux versions.
So, use a kmalloc'ed buffer.
Cc: stable@vger.kernel.org # Kernel 4.9 and upper
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a30dc6cf0d upstream.
I got a NULL pointer dereference report when doing fuzz test:
Call Trace:
qp_release_pages+0xae/0x130
qp_host_unregister_user_memory.isra.25+0x2d/0x80
vmci_qp_broker_unmap+0x191/0x320
? vmci_host_do_alloc_queuepair.isra.9+0x1c0/0x1c0
vmci_host_unlocked_ioctl+0x59f/0xd50
? do_vfs_ioctl+0x14b/0xa10
? tomoyo_file_ioctl+0x28/0x30
? vmci_host_do_alloc_queuepair.isra.9+0x1c0/0x1c0
__x64_sys_ioctl+0xea/0x120
do_syscall_64+0x34/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
When a queue pair is created by the following call, it will not
register the user memory if the page_store is NULL, and the
entry->state will be set to VMCIQPB_CREATED_NO_MEM.
vmci_host_unlocked_ioctl
vmci_host_do_alloc_queuepair
vmci_qp_broker_alloc
qp_broker_alloc
qp_broker_create // set entry->state = VMCIQPB_CREATED_NO_MEM;
When unmapping this queue pair, qp_host_unregister_user_memory() will
be called to unregister the non-existent user memory, which will
result in a null pointer reference. It will also change
VMCIQPB_CREATED_NO_MEM to VMCIQPB_CREATED_MEM, which should not be
present in this operation.
Only when the qp broker has mem, it can unregister the user
memory when unmapping the qp broker.
Only when the qp broker has no mem, it can register the user
memory when mapping the qp broker.
Fixes: 06164d2b72 ("VMCI: queue pairs implementation.")
Cc: stable <stable@vger.kernel.org>
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Link: https://lore.kernel.org/r/20210818124845.488312-1-wanghai38@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5441a07a12 upstream.
The commit 97f9ac3db6 ("crypto: ccp - Add support for SEV-ES to the
PSP driver") added support to allocate Trusted Memory Region (TMR)
used during the SEV-ES firmware initialization. The TMR gets locked
during the firmware initialization and unlocked during the shutdown.
While the TMR is locked, access to it is disallowed.
Currently, the CCP driver does not shutdown the firmware during the
kexec reboot, leaving the TMR memory locked.
Register a callback to shutdown the SEV firmware on the kexec boot.
Fixes: 97f9ac3db6 ("crypto: ccp - Add support for SEV-ES to the PSP driver")
Reported-by: Lucas Nussbaum <lucas.nussbaum@inria.fr>
Tested-by: Lucas Nussbaum <lucas.nussbaum@inria.fr>
Cc: <stable@kernel.org>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 528b16bfc3 upstream.
On systems with many cores using dm-crypt, heavy spinlock contention in
percpu_counter_compare() can be observed when the page allocation limit
for a given device is reached or close to be reached. This is due
to percpu_counter_compare() taking a spinlock to compute an exact
result on potentially many CPUs at the same time.
Switch to non-exact comparison of allocated and allowed pages by using
the value returned by percpu_counter_read_positive() to avoid taking
the percpu_counter spinlock.
This may over/under estimate the actual number of allocated pages by at
most (batch-1) * num_online_cpus().
Currently, batch is bounded by 32. The system on which this issue was
first observed has 256 CPUs and 512GB of RAM. With a 4k page size, this
change may over/under estimate by 31MB. With ~10G (2%) allowed dm-crypt
allocations, this seems an acceptable error. Certainly preferred over
running into the spinlock contention.
This behavior was reproduced on an EC2 c5.24xlarge instance with 96 CPUs
and 192GB RAM as follows, but can be provoked on systems with less CPUs
as well.
* Disable swap
* Tune vm settings to promote regular writeback
$ echo 50 > /proc/sys/vm/dirty_expire_centisecs
$ echo 25 > /proc/sys/vm/dirty_writeback_centisecs
$ echo $((128 * 1024 * 1024)) > /proc/sys/vm/dirty_background_bytes
* Create 8 dmcrypt devices based on files on a tmpfs
* Create and mount an ext4 filesystem on each crypt devices
* Run stress-ng --hdd 8 within one of above filesystems
Total %system usage collected from sysstat goes to ~35%. Write throughput
on the underlying loop device is ~2GB/s. perf profiling an individual
kworker kcryptd thread shows the following profile, indicating spinlock
contention in percpu_counter_compare():
99.98% 0.00% kworker/u193:46 [kernel.kallsyms] [k] ret_from_fork
|
--ret_from_fork
kthread
worker_thread
|
--99.92%--process_one_work
|
|--80.52%--kcryptd_crypt
| |
| |--62.58%--mempool_alloc
| | |
| | --62.24%--crypt_page_alloc
| | |
| | --61.51%--__percpu_counter_compare
| | |
| | --61.34%--__percpu_counter_sum
| | |
| | |--58.68%--_raw_spin_lock_irqsave
| | | |
| | | --58.30%--native_queued_spin_lock_slowpath
| | |
| | --0.69%--cpumask_next
| | |
| | --0.51%--_find_next_bit
| |
| |--10.61%--crypt_convert
| | |
| | |--6.05%--xts_crypt
...
After applying this patch and running the same test, %system usage is
lowered to ~7% and write throughput on the loop device increases
to ~2.7GB/s. perf report shows mempool_alloc() as ~8% rather than ~62%
in the profile and not hitting the percpu_counter() spinlock anymore.
|--8.15%--mempool_alloc
| |
| |--3.93%--crypt_page_alloc
| | |
| | --3.75%--__alloc_pages
| | |
| | --3.62%--get_page_from_freelist
| | |
| | --3.22%--rmqueue_bulk
| | |
| | --2.59%--_raw_spin_lock
| | |
| | --2.57%--native_queued_spin_lock_slowpath
| |
| --3.05%--_raw_spin_lock_irqsave
| |
| --2.49%--native_queued_spin_lock_slowpath
Suggested-by: DJ Gregor <dj@corelight.com>
Reviewed-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Arne Welzel <arne.welzel@corelight.com>
Fixes: 5059353df8 ("dm crypt: limit the number of allocated pages")
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54784ffa5b upstream.
Reading status register can fail in the interrupt handler. In such
case, the regmap_read() will not store anything useful under passed
'val' variable and random stack value will be used to determine type of
interrupt.
Handle the regmap_read() failure to avoid handling interrupt type and
triggering changed power supply event based on random stack value.
Fixes: 39e7213edc ("max17042_battery: Support regmap to access device's registers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a680dd72ec upstream.
For a request that has a priority level equal to or larger than
IOPRIO_BE_NR, bfq_set_next_ioprio_data() prints a critical warning but
defaults to setting the request new_ioprio field to IOPRIO_BE_NR. This
is not consistent with the warning and the allowed values for priority
levels. Fix this by setting the request new_ioprio field to
IOPRIO_BE_NR - 1, the lowest priority level allowed.
Cc: <stable@vger.kernel.org>
Fixes: aee69d78de ("block, bfq: introduce the BFQ-v0 I/O scheduler as an extra scheduler")
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20210811033702.368488-2-damien.lemoal@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b76d26d69e upstream.
There is no reason to assume that the IRQ rising edge (indicating that
the device start up phase is done) will happen after we request the IRQ.
If the device is already up by the time we request it, the call to
'wait_for_completion_timeout()' will timeout and we will fail the device
probe even though there's nothing wrong.
Fix it by just polling the status register until we get the indication that
the device is up and running. As a side effect of this fix, requesting the
IRQ is also moved to after the setup function.
Fixes: f110f3188e ("iio: temperature: Add support for LTC2983")
Reported-and-tested-by: Drew Fustini <drew@pdp7.com>
Reviewed-by: Drew Fustini <drew@pdp7.com>
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210811133220.190264-2-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90268574a3 upstream.
The `compute_indices` and `populate_entries` macros operate on inclusive
bounds, and thus the `map_memory` macro which uses them also operates
on inclusive bounds.
We pass `_end` and `_idmap_text_end` to `map_memory`, but these are
exclusive bounds, and if one of these is sufficiently aligned (as a
result of kernel configuration, physical placement, and KASLR), then:
* In `compute_indices`, the computed `iend` will be in the page/block *after*
the final byte of the intended mapping.
* In `populate_entries`, an unnecessary entry will be created at the end
of each level of table. At the leaf level, this entry will map up to
SWAPPER_BLOCK_SIZE bytes of physical addresses that we did not intend
to map.
As we may map up to SWAPPER_BLOCK_SIZE bytes more than intended, we may
violate the boot protocol and map physical address past the 2MiB-aligned
end address we are permitted to map. As we map these with Normal memory
attributes, this may result in further problems depending on what these
physical addresses correspond to.
The final entry at each level may require an additional table at that
level. As EARLY_ENTRIES() calculates an inclusive bound, we allocate
enough memory for this.
Avoid the extraneous mapping by having map_memory convert the exclusive
end address to an inclusive end address by subtracting one, and do
likewise in EARLY_ENTRIES() when calculating the number of required
tables. For clarity, comments are updated to more clearly document which
boundaries the macros operate on. For consistency with the other
macros, the comments in map_memory are also updated to describe `vstart`
and `vend` as virtual addresses.
Fixes: 0370b31e48 ("arm64: Extend early page table code to allow for larger kernels")
Cc: <stable@vger.kernel.org> # 4.16.x
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Steve Capper <steve.capper@arm.com>
Cc: Will Deacon <will@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210823101253.55567-1-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e10f9887e upstream.
When switching to an 'mm_struct' for the first time following an ASID
rollover, a new ASID may be allocated and assigned to 'mm->context.id'.
This reassignment can happen concurrently with other operations on the
mm, such as unmapping pages and subsequently issuing TLB invalidation.
Consequently, we need to ensure that (a) accesses to 'mm->context.id'
are atomic and (b) all page-table updates made prior to a TLBI using the
old ASID are guaranteed to be visible to CPUs running with the new ASID.
This was found by inspection after reviewing the VMID changes from
Shameer but it looks like a real (yet hard to hit) bug.
Cc: <stable@vger.kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Jade Alglave <jade.alglave@arm.com>
Cc: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Signed-off-by: Will Deacon <will@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20210806113109.2475-2-will@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b07e990fb upstream.
The check mixes pages (vm_pgoff) with bytes (vm_start, vm_end) on one
side of the comparison, and uses resource address (rather than just the
resource size) on the other side of the comparison.
This can allow malicious userspace to easily bypass the boundary check and
map pages that are located outside memory-region reserved by the driver.
Fixes: 01c60dcea9 ("drivers/misc: Add Aspeed P2A control driver")
Cc: stable@vger.kernel.org
Signed-off-by: Iwona Winiarska <iwona.winiarska@intel.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Tested-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b49a0e69a7 upstream.
The check mixes pages (vm_pgoff) with bytes (vm_start, vm_end) on one
side of the comparison, and uses resource address (rather than just the
resource size) on the other side of the comparison.
This can allow malicious userspace to easily bypass the boundary check and
map pages that are located outside memory-region reserved by the driver.
Fixes: 6c4e976785 ("drivers/misc: Add Aspeed LPC control driver")
Cc: stable@vger.kernel.org
Signed-off-by: Iwona Winiarska <iwona.winiarska@intel.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Tested-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a89f355e46 upstream.
In "qmp_cooling_devices_register", the count value is initially
QMP_NUM_COOLING_RESOURCES, which is 2. Based on the initial count value,
the memory for cooling_devs is allocated. Then while calling the
"qmp_cooling_device_add" function, count value is post-incremented for
each child node.
This makes the out of bound access to the cooling_dev array. Fix it by
passing the QMP_NUM_COOLING_RESOURCES definition to devm_kzalloc() and
initializing the count to 0.
While at it, let's also free the memory allocated to cooling_dev if no
cooling device is found in DT and during unroll phase.
Cc: stable@vger.kernel.org # 5.4
Fixes: 05589b30b2 ("soc: qcom: Extend AOSS QMP driver to support resources that are used to wake up the SoC.")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210629153249.73428-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05a444d3f9 upstream.
Currently in the case where kmem_cache_alloc fails the null pointer
cf is dereferenced when assigning cf->is_capsnap = false. Fix this
by adding a null pointer check and return path.
Cc: stable@vger.kernel.org
Addresses-Coverity: ("Dereference null return")
Fixes: b2f9fa1f3b ("ceph: correctly handle releasing an embedded cap flush")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b511d5bfa upstream.
Xen PV guests are specifying the highest used PFN via the max_pfn
field in shared_info. This value is used by the Xen tools when saving
or migrating the guest.
Unfortunately this field is misnamed, as in reality it is specifying
the number of pages (including any memory holes) of the guest, so it
is the highest used PFN + 1. Renaming isn't possible, as this is a
public Xen hypervisor interface which needs to be kept stable.
The kernel will set the value correctly initially at boot time, but
when adding more pages (e.g. due to memory hotplug or ballooning) a
real PFN number is stored in max_pfn. This is done when expanding the
p2m array, and the PFN stored there is even possibly wrong, as it
should be the last possible PFN of the just added P2M frame, and not
one which led to the P2M expansion.
Fix that by setting shared_info->max_pfn to the last possible PFN + 1.
Fixes: 98dd166ea3 ("x86/xen/p2m: hint at the last populated P2M entry")
Cc: stable@vger.kernel.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Link: https://lore.kernel.org/r/20210730092622.9973-2-jgross@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9addd85fb upstream.
H_GetPerformanceCounterInfo (0xF080) hcall returns the counter data in
the result buffer. Result buffer has specific format defined in the PAPR
specification. One of the fields is counter offset and width of the
counter data returned.
Counter data are returned in a unsigned char array in big endian byte
order. To get the final counter data, the values must be left shifted
byte at a time. But commit 220a0c609a ("powerpc/perf: Add support for
the hv gpci (get performance counter info) interface") made the shifting
bitwise and also assumed little endian order. Because of that, hcall
counters values are reported incorrectly.
In particular this can lead to counters go backwards which messes up the
counter prev vs now calculation and leads to huge counter value
reporting:
#: perf stat -e hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
-C 0 -I 1000
time counts unit events
1.000078854 18,446,744,073,709,535,232 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
2.000213293 0 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
3.000320107 0 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
4.000428392 0 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
5.000537864 0 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
6.000649087 0 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
7.000760312 0 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
8.000865218 16,448 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
9.000978985 18,446,744,073,709,535,232 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
10.001088891 16,384 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
11.001201435 0 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
12.001307937 18,446,744,073,709,535,232 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
Fix the shifting logic to correct match the format, ie. read bytes in
big endian order.
Fixes: e4f226b158 ("powerpc/perf/hv-gpci: Increase request buffer size")
Cc: stable@vger.kernel.org # v4.6+
Reported-by: Nageswara R Sastry<rnsastry@linux.ibm.com>
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
Tested-by: Nageswara R Sastry<rnsastry@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210813082158.429023-1-kjain@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a519dc7a7 upstream.
When running as Xen PV guest, masking MSI-X is a responsibility of the
hypervisor. The guest has no write access to the relevant BAR at all - when
it tries to, it results in a crash like this:
BUG: unable to handle page fault for address: ffffc9004069100c
#PF: supervisor write access in kernel mode
#PF: error_code(0x0003) - permissions violation
RIP: e030:__pci_enable_msix_range.part.0+0x26b/0x5f0
e1000e_set_interrupt_capability+0xbf/0xd0 [e1000e]
e1000_probe+0x41f/0xdb0 [e1000e]
local_pci_probe+0x42/0x80
(...)
The recently introduced function msix_mask_all() does not check the global
variable pci_msi_ignore_mask which is set by XEN PV to bypass the masking
of MSI[-X] interrupts.
Add the check to make this function XEN PV compatible.
Fixes: 7d5ec3d361 ("PCI/MSI: Mask all unused MSI-X entries")
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210826170342.135172-1-marmarek@invisiblethingslab.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ead3b768bb upstream.
Zone management send operations (BLKRESETZONE, BLKOPENZONE, BLKCLOSEZONE
and BLKFINISHZONE) should be allowed under the same permissions as write().
(write() does not require CAP_SYS_ADMIN).
Additionally, other ioctls like BLKSECDISCARD and BLKZEROOUT only check if
the fd was successfully opened with FMODE_WRITE.
(They do not require CAP_SYS_ADMIN).
Currently, zone management send operations require both CAP_SYS_ADMIN
and that the fd was successfully opened with FMODE_WRITE.
Remove the CAP_SYS_ADMIN requirement, so that zone management send
operations match the access control requirement of write(), BLKSECDISCARD
and BLKZEROOUT.
Fixes: 3ed05a987e ("blk-zoned: implement ioctls")
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Aravind Ramesh <aravind.ramesh@wdc.com>
Reviewed-by: Adam Manzanares <a.manzanares@samsung.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Cc: stable@vger.kernel.org # v4.10+
Link: https://lore.kernel.org/r/20210811110505.29649-2-Niklas.Cassel@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d977e0eba upstream.
This crash was observed with a failed assertion on device close:
BTRFS: Transaction aborted (error -28)
WARNING: CPU: 1 PID: 3902 at fs/btrfs/extent-tree.c:2150 btrfs_run_delayed_refs+0x1d2/0x1e0 [btrfs]
Modules linked in: btrfs blake2b_generic libcrc32c crc32c_intel xor zstd_decompress zstd_compress xxhash lzo_compress lzo_decompress raid6_pq loop
CPU: 1 PID: 3902 Comm: kworker/u8:4 Not tainted 5.14.0-rc5-default+ #1532
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-59-gc9ba527-rebuilt.opensuse.org 04/01/2014
Workqueue: events_unbound btrfs_async_reclaim_metadata_space [btrfs]
RIP: 0010:btrfs_run_delayed_refs+0x1d2/0x1e0 [btrfs]
RSP: 0018:ffffb7a5452d7d80 EFLAGS: 00010282
RAX: 0000000000000000 RBX: 0000000000000003 RCX: 0000000000000000
RDX: 0000000000000001 RSI: ffffffffabee13c4 RDI: 00000000ffffffff
RBP: ffff97834176a378 R08: 0000000000000001 R09: 0000000000000001
R10: 0000000000000000 R11: 0000000000000001 R12: ffff97835195d388
R13: 0000000005b08000 R14: ffff978385484000 R15: 000000000000016c
FS: 0000000000000000(0000) GS:ffff9783bd800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000056190d003fe8 CR3: 000000002a81e005 CR4: 0000000000170ea0
Call Trace:
flush_space+0x197/0x2f0 [btrfs]
btrfs_async_reclaim_metadata_space+0x139/0x300 [btrfs]
process_one_work+0x262/0x5e0
worker_thread+0x4c/0x320
? process_one_work+0x5e0/0x5e0
kthread+0x144/0x170
? set_kthread_struct+0x40/0x40
ret_from_fork+0x1f/0x30
irq event stamp: 19334989
hardirqs last enabled at (19334997): [<ffffffffab0e0c87>] console_unlock+0x2b7/0x400
hardirqs last disabled at (19335006): [<ffffffffab0e0d0d>] console_unlock+0x33d/0x400
softirqs last enabled at (19334900): [<ffffffffaba0030d>] __do_softirq+0x30d/0x574
softirqs last disabled at (19334893): [<ffffffffab0721ec>] irq_exit_rcu+0x12c/0x140
---[ end trace 45939e308e0dd3c7 ]---
BTRFS: error (device vdd) in btrfs_run_delayed_refs:2150: errno=-28 No space left
BTRFS info (device vdd): forced readonly
BTRFS warning (device vdd): failed setting block group ro: -30
BTRFS info (device vdd): suspending dev_replace for unmount
assertion failed: !test_bit(BTRFS_DEV_STATE_REPLACE_TGT, &device->dev_state), in fs/btrfs/volumes.c:1150
------------[ cut here ]------------
kernel BUG at fs/btrfs/ctree.h:3431!
invalid opcode: 0000 [#1] PREEMPT SMP
CPU: 1 PID: 3982 Comm: umount Tainted: G W 5.14.0-rc5-default+ #1532
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-59-gc9ba527-rebuilt.opensuse.org 04/01/2014
RIP: 0010:assertfail.constprop.0+0x18/0x1a [btrfs]
RSP: 0018:ffffb7a5454c7db8 EFLAGS: 00010246
RAX: 0000000000000068 RBX: ffff978364b91c00 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffffffabee13c4 RDI: 00000000ffffffff
RBP: ffff9783523a4c00 R08: 0000000000000001 R09: 0000000000000001
R10: 0000000000000000 R11: 0000000000000001 R12: ffff9783523a4d18
R13: 0000000000000000 R14: 0000000000000004 R15: 0000000000000003
FS: 00007f61c8f42800(0000) GS:ffff9783bd800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000056190cffa810 CR3: 0000000030b96002 CR4: 0000000000170ea0
Call Trace:
btrfs_close_one_device.cold+0x11/0x55 [btrfs]
close_fs_devices+0x44/0xb0 [btrfs]
btrfs_close_devices+0x48/0x160 [btrfs]
generic_shutdown_super+0x69/0x100
kill_anon_super+0x14/0x30
btrfs_kill_super+0x12/0x20 [btrfs]
deactivate_locked_super+0x2c/0xa0
cleanup_mnt+0x144/0x1b0
task_work_run+0x59/0xa0
exit_to_user_mode_loop+0xe7/0xf0
exit_to_user_mode_prepare+0xaf/0xf0
syscall_exit_to_user_mode+0x19/0x50
do_syscall_64+0x4a/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
This happens when close_ctree is called while a dev_replace hasn't
completed. In close_ctree, we suspend the dev_replace, but keep the
replace target around so that we can resume the dev_replace procedure
when we mount the root again. This is the call trace:
close_ctree():
btrfs_dev_replace_suspend_for_unmount();
btrfs_close_devices():
btrfs_close_fs_devices():
btrfs_close_one_device():
ASSERT(!test_bit(BTRFS_DEV_STATE_REPLACE_TGT,
&device->dev_state));
However, since the replace target sticks around, there is a device
with BTRFS_DEV_STATE_REPLACE_TGT set on close, and we fail the
assertion in btrfs_close_one_device.
To fix this, if we come across the replace target device when
closing, we should properly reset it back to allocation state. This
fix also ensures that if a non-target device has a corrupted state and
has the BTRFS_DEV_STATE_REPLACE_TGT bit set, the assertion will still
catch the error.
Reported-by: David Sterba <dsterba@suse.com>
Fixes: b2a6166768 ("btrfs: fix rw device counting in __btrfs_free_extra_devids")
CC: stable@vger.kernel.org # 4.19+
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac98141d14 upstream.
We use the async_delalloc_pages mechanism to make sure that we've
completed our async work before trying to continue our delalloc
flushing. The reason for this is we need to see any ordered extents
that were created by our delalloc flushing. However we're waking up
before we do the submit work, which is before we create the ordered
extents. This is a pretty wide race window where we could potentially
think there are no ordered extents and thus exit shrink_delalloc
prematurely. Fix this by waking us up after we've done the work to
create ordered extents.
CC: stable@vger.kernel.org # 5.4+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87df7fb922 upstream.
When new work is added, io_wqe_enqueue() checks if we need to wake or
create a new worker. But that check is done outside the lock that
otherwise synchronizes us with a worker going to sleep, so we can end
up in the following situation:
CPU0 CPU1
lock
insert work
unlock
atomic_read(nr_running) != 0
lock
atomic_dec(nr_running)
no wakeup needed
Hold the wqe lock around the "need to wakeup" check. Then we can also get
rid of the temporary work_flags variable, as we know the work will remain
valid as long as we hold the lock.
Cc: stable@vger.kernel.org
Reported-by: Andres Freund <andres@anarazel.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 4711284768.
Botched backport, dropping to rework for next release.
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
As we're wanting to wrap the image_fx component for deinterlacing,
add the deinterlace algorithm values to enum mmal_parameter_imagefx
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
commit aaedb9e00e upstream.
Since a few kernel releases the Pogoplug 4 has crashed like this
during boot:
Unable to handle kernel NULL pointer dereference at virtual address 00000002
(...)
[<c04116ec>] (strlen) from [<c00ead80>] (kstrdup+0x1c/0x4c)
[<c00ead80>] (kstrdup) from [<c04591d8>] (__clk_register+0x44/0x37c)
[<c04591d8>] (__clk_register) from [<c04595ec>] (clk_hw_register+0x20/0x44)
[<c04595ec>] (clk_hw_register) from [<c045bfa8>] (__clk_hw_register_mux+0x198/0x1e4)
[<c045bfa8>] (__clk_hw_register_mux) from [<c045c050>] (clk_register_mux_table+0x5c/0x6c)
[<c045c050>] (clk_register_mux_table) from [<c0acf3e0>] (kirkwood_clk_muxing_setup.constprop.0+0x13c/0x1ac)
[<c0acf3e0>] (kirkwood_clk_muxing_setup.constprop.0) from [<c0aceae0>] (of_clk_init+0x12c/0x214)
[<c0aceae0>] (of_clk_init) from [<c0ab576c>] (time_init+0x20/0x2c)
[<c0ab576c>] (time_init) from [<c0ab3d18>] (start_kernel+0x3dc/0x56c)
[<c0ab3d18>] (start_kernel) from [<00000000>] (0x0)
Code: e3130020 1afffffb e12fff1e c08a1078 (e5d03000)
This is because the "powersave" mux clock 0 was provided in an unterminated
array, which is required by the loop in the driver:
/* Count, allocate, and register clock muxes */
for (n = 0; desc[n].name;)
n++;
Here n will go out of bounds and then call clk_register_mux() on random
memory contents after the mux clock.
Fix this by terminating the array with a blank entry.
Fixes: 105299381d ("cpufreq: kirkwood: use the powersave multiplexer")
Cc: stable@vger.kernel.org
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210814235514.403426-1-linus.walleij@linaro.org
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 79fad92f2e upstream.
Currently there are (at least) two problems in the way pwm_bl starts
managing the enable_gpio pin. Both occur when the backlight is initially
off and the driver finds the pin not already in output mode and, as a
result, unconditionally switches it to output-mode and asserts the signal.
Problem 1: This could cause the backlight to flicker since, at this stage
in driver initialisation, we have no idea what the PWM and regulator are
doing (an unconfigured PWM could easily "rest" at 100% duty cycle).
Problem 2: This will cause us not to correctly honour the
post_pwm_on_delay (which also risks flickers).
Fix this by moving the code to configure the GPIO output mode until after
we have examines the handover state. That allows us to initialize
enable_gpio to off if the backlight is currently off and on if the
backlight is on.
Cc: stable@vger.kernel.org
Reported-by: Marek Vasut <marex@denx.de>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8510505d55 upstream.
MD5 is a weak digest algorithm that shouldn't be used for cryptographic
operation. It hinders the efficiency of a patch set that aims to limit
the digests allowed for the extended file attribute namely security.ima.
MD5 is no longer a requirement for IMA, nor should it be used there.
The sole place where we still use the MD5 algorithm inside IMA is setting
the ima_hash algorithm to MD5, if the user supplies 'ima_hash=md5'
parameter on the command line. With commit ab60368ab6 ("ima: Fallback
to the builtin hash algorithm"), setting "ima_hash=md5" fails gracefully
when CRYPTO_MD5 is not set:
ima: Can not allocate md5 (reason: -2)
ima: Allocating md5 failed, going to use default hash algorithm sha256
Remove the CRYPTO_MD5 dependency for IMA.
Signed-off-by: THOBY Simon <Simon.THOBY@viveris.fr>
Reviewed-by: Lakshmi Ramasubramanian <nramas@linux.microsoft.com>
[zohar@linux.ibm.com: include commit number in patch description for
stable.]
Cc: stable@vger.kernel.org # 4.17
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 59bda8ecee upstream.
Callers of fuse_writeback_range() assume that the file is ready for
modification by the server in the supplied byte range after the call
returns.
If there's a write that extends the file beyond the end of the supplied
range, then the file needs to be extended to at least the end of the range,
but currently that's not done.
There are at least two cases where this can cause problems:
- copy_file_range() will return short count if the file is not extended
up to end of the source range.
- FALLOC_FL_ZERO_RANGE | FALLOC_FL_KEEP_SIZE will not extend the file,
hence the region may not be fully allocated.
Fix by flushing writes from the start of the range up to the end of the
file. This could be optimized if the writes are non-extending, etc, but
it's probably not worth the trouble.
Fixes: a2bc923629 ("fuse: fix copy_file_range() in the writeback case")
Fixes: 6b1bdb56b1 ("fuse: allow fallocate(FALLOC_FL_ZERO_RANGE)")
Cc: <stable@vger.kernel.org> # v5.2
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 76224355db upstream.
fuse_finish_open() will be called with FUSE_NOWRITE in case of atomic
O_TRUNC. This can deadlock with fuse_wait_on_page_writeback() in
fuse_launder_page() triggered by invalidate_inode_pages2().
Fix by replacing invalidate_inode_pages2() in fuse_finish_open() with a
truncate_pagecache() call. This makes sense regardless of FOPEN_KEEP_CACHE
or fc->writeback cache, so do it unconditionally.
Reported-by: Xie Yongji <xieyongji@bytedance.com>
Reported-and-tested-by: syzbot+bea44a5189836d956894@syzkaller.appspotmail.com
Fixes: e4648309b8 ("fuse: truncate pending writes on O_TRUNC")
Cc: <stable@vger.kernel.org>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7782bb8d8 upstream.
Clear nested.pi_pending on nested VM-Enter even if L2 will run without
posted interrupts enabled. If nested.pi_pending is left set from a
previous L2, vmx_complete_nested_posted_interrupt() will pick up the
stale flag and exit to userspace with an "internal emulation error" due
the new L2 not having a valid nested.pi_desc.
Arguably, vmx_complete_nested_posted_interrupt() should first check for
posted interrupts being enabled, but it's also completely reasonable that
KVM wouldn't screw up a fundamental flag. Not to mention that the mere
existence of nested.pi_pending is a long-standing bug as KVM shouldn't
move the posted interrupt out of the IRR until it's actually processed,
e.g. KVM effectively drops an interrupt when it performs a nested VM-Exit
with a "pending" posted interrupt. Fixing the mess is a future problem.
Prior to vmx_complete_nested_posted_interrupt() interpreting a null PI
descriptor as an error, this was a benign bug as the null PI descriptor
effectively served as a check on PI not being enabled. Even then, the
new flow did not become problematic until KVM started checking the result
of kvm_check_nested_events().
Fixes: 705699a139 ("KVM: nVMX: Enable nested posted interrupt processing")
Fixes: 966eefb896 ("KVM: nVMX: Disable vmcs02 posted interrupts if vmcs12 PID isn't mappable")
Fixes: 47d3530f86c0 ("KVM: x86: Exit to userspace when kvm_check_nested_events fails")
Cc: stable@vger.kernel.org
Cc: Jim Mattson <jmattson@google.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210810144526.2662272-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9130a2dfd upstream.
When MSR_IA32_TSC_ADJUST is written by guest due to TSC ADJUST feature
especially there's a big tsc warp (like a new vCPU is hot-added into VM
which has been up for a long time), tsc_offset is added by a large value
then go back to guest. This causes system time jump as tsc_timestamp is
not adjusted in the meantime and pvclock monotonic character.
To fix this, just notify kvm to update vCPU's guest time before back to
guest.
Cc: stable@vger.kernel.org
Signed-off-by: Zelin Deng <zelin.deng@linux.alibaba.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1619576521-81399-2-git-send-email-zelin.deng@linux.alibaba.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a3e03bc136 upstream.
While in practice vcpu->vcpu_idx == vcpu->vcp_id is often true, it may
not always be, and we must not rely on this. Reason is that KVM decides
the vcpu_idx, userspace decides the vcpu_id, thus the two might not
match.
Currently kvm->arch.idle_mask is indexed by vcpu_id, which implies
that code like
for_each_set_bit(vcpu_id, kvm->arch.idle_mask, online_vcpus) {
vcpu = kvm_get_vcpu(kvm, vcpu_id);
do_stuff(vcpu);
}
is not legit. Reason is that kvm_get_vcpu expects an vcpu_idx, not an
vcpu_id. The trouble is, we do actually use kvm->arch.idle_mask like
this. To fix this problem we have two options. Either use
kvm_get_vcpu_by_id(vcpu_id), which would loop to find the right vcpu_id,
or switch to indexing via vcpu_idx. The latter is preferable for obvious
reasons.
Let us make switch from indexing kvm->arch.idle_mask by vcpu_id to
indexing it by vcpu_idx. To keep gisa_int.kicked_mask indexed by the
same index as idle_mask lets make the same change for it as well.
Fixes: 1ee0bc559d ("KVM: s390: get rid of local_int array")
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Christian Bornträger <borntraeger@de.ibm.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Cc: <stable@vger.kernel.org> # 3.15+
Link: https://lore.kernel.org/r/20210827125429.1912577-1-pasic@linux.ibm.com
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7177339d7 upstream.
Revert a misguided illegal GPA check when "translating" a non-nested GPA.
The check is woefully incomplete as it does not fill in @exception as
expected by all callers, which leads to KVM attempting to inject a bogus
exception, potentially exposing kernel stack information in the process.
WARNING: CPU: 0 PID: 8469 at arch/x86/kvm/x86.c:525 exception_type+0x98/0xb0 arch/x86/kvm/x86.c:525
CPU: 1 PID: 8469 Comm: syz-executor531 Not tainted 5.14.0-rc7-syzkaller #0
RIP: 0010:exception_type+0x98/0xb0 arch/x86/kvm/x86.c:525
Call Trace:
x86_emulate_instruction+0xef6/0x1460 arch/x86/kvm/x86.c:7853
kvm_mmu_page_fault+0x2f0/0x1810 arch/x86/kvm/mmu/mmu.c:5199
handle_ept_misconfig+0xdf/0x3e0 arch/x86/kvm/vmx/vmx.c:5336
__vmx_handle_exit arch/x86/kvm/vmx/vmx.c:6021 [inline]
vmx_handle_exit+0x336/0x1800 arch/x86/kvm/vmx/vmx.c:6038
vcpu_enter_guest+0x2a1c/0x4430 arch/x86/kvm/x86.c:9712
vcpu_run arch/x86/kvm/x86.c:9779 [inline]
kvm_arch_vcpu_ioctl_run+0x47d/0x1b20 arch/x86/kvm/x86.c:10010
kvm_vcpu_ioctl+0x49e/0xe50 arch/x86/kvm/../../../virt/kvm/kvm_main.c:3652
The bug has escaped notice because practically speaking the GPA check is
useless. The GPA check in question only comes into play when KVM is
walking guest page tables (or "translating" CR3), and KVM already handles
illegal GPA checks by setting reserved bits in rsvd_bits_mask for each
PxE, or in the case of CR3 for loading PTDPTRs, manually checks for an
illegal CR3. This particular failure doesn't hit the existing reserved
bits checks because syzbot sets guest.MAXPHYADDR=1, and IA32 architecture
simply doesn't allow for such an absurd MAXPHYADDR, e.g. 32-bit paging
doesn't define any reserved PA bits checks, which KVM emulates by only
incorporating the reserved PA bits into the "high" bits, i.e. bits 63:32.
Simply remove the bogus check. There is zero meaningful value and no
architectural justification for supporting guest.MAXPHYADDR < 32, and
properly filling the exception would introduce non-trivial complexity.
This reverts commit ec7771ab47.
Fixes: ec7771ab47 ("KVM: x86: mmu: Add guest physical address check in translate_gpa()")
Cc: stable@vger.kernel.org
Reported-by: syzbot+200c08e88ae818f849ce@syzkaller.appspotmail.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210831164224.1119728-2-seanjc@google.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 527f721478 upstream.
The recent commit
064855a690 ("x86/resctrl: Fix default monitoring groups reporting")
caused a RHEL build failure with an uninitialized variable warning
treated as an error because it removed the default case snippet.
The RHEL Makefile uses '-Werror=maybe-uninitialized' to force possibly
uninitialized variable warnings to be treated as errors. This is also
reported by smatch via the 0day robot.
The error from the RHEL build is:
arch/x86/kernel/cpu/resctrl/monitor.c: In function ‘__mon_event_count’:
arch/x86/kernel/cpu/resctrl/monitor.c:261:12: error: ‘m’ may be used
uninitialized in this function [-Werror=maybe-uninitialized]
m->chunks += chunks;
^~
The upstream Makefile does not build using '-Werror=maybe-uninitialized'.
So, the problem is not seen there. Fix the problem by putting back the
default case snippet.
[ bp: note that there's nothing wrong with the code and other compilers
do not trigger this warning - this is being done just so the RHEL compiler
is happy. ]
Fixes: 064855a690 ("x86/resctrl: Fix default monitoring groups reporting")
Reported-by: Terry Bowman <Terry.Bowman@amd.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/162949631908.23903.17090272726012848523.stgit@bmoger-ubuntu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb2853a6a4 upstream.
The ops->receive_buf() may be accessed concurrently from these two
functions. If the driver flushes data to the line discipline
receive_buf() method while tiocsti() is waiting for the
ops->receive_buf() to finish its work, the data race will happen.
For example:
tty_ioctl |tty_ldisc_receive_buf
->tioctsi | ->tty_port_default_receive_buf
| ->tty_ldisc_receive_buf
->hci_uart_tty_receive | ->hci_uart_tty_receive
->h4_recv | ->h4_recv
In this case, the h4 receive buffer will be overwritten by the
latecomer, and we will lost the data.
Hence, change tioctsi() function to use the exclusive lock interface
from tty_buffer to avoid the data race.
Reported-by: syzbot+97388eb9d31b997fe1d0@syzkaller.appspotmail.com
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Nguyen Dinh Phi <phind.uet@gmail.com>
Link: https://lore.kernel.org/r/20210823000641.2082292-1-phind.uet@gmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b3188e7ed upstream.
During some testing, it became evident that using IORING_OP_WRITE doesn't
hash buffered writes like the other writes commands do. That's simply
an oversight, and can cause performance regressions when doing buffered
writes with this command.
Correct that and add the flag, so that buffered writes are correctly
hashed when using the non-iovec based write command.
Cc: stable@vger.kernel.org
Fixes: 3a6820f2bb ("io_uring: add non-vectored read/write commands")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39ff83f2f6 upstream.
timespec64_ns() prevents multiplication overflows by comparing the seconds
value of the timespec to KTIME_SEC_MAX. If the value is greater or equal it
returns KTIME_MAX.
But that check casts the signed seconds value to unsigned which makes the
comparision true for all negative values and therefore return wrongly
KTIME_MAX.
Negative second values are perfectly valid and required in some places,
e.g. ptp_clock_adjtime().
Remove the cast and add a check for the negative boundary which is required
to prevent undefined behaviour due to multiplication underflow.
Fixes: cb47755725 ("time: Prevent undefined behaviour in timespec64_to_ns()")'
Signed-off-by: Lukas Hannen <lukas.hannen@opensource.tttech-industrial.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/AM6PR01MB541637BD6F336B8FFB72AF80EEC69@AM6PR01MB5416.eurprd01.prod.exchangelabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dddd3d6529 upstream.
We must flush all the dirty data when enabling checkpoint back. Let's guarantee
that first by adding a retry logic on sync_inodes_sb(). In addition to that,
this patch adds to flush data in fsync when checkpoint is disabled, which can
mitigate the sync_inodes_sb() failures in advance.
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 92548b0ee2 ]
The UDP length field should be in network order.
This removes the following sparse error:
net/ipv4/route.c:3173:27: warning: incorrect type in assignment (different base types)
net/ipv4/route.c:3173:27: expected restricted __be16 [usertype] len
net/ipv4/route.c:3173:27: got unsigned long
Fixes: 404eb77ea7 ("ipv4: support sport, dport and ip_proto in RTM_GETROUTE")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Roopa Prabhu <roopa@nvidia.com>
Cc: David Ahern <dsahern@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e4428b6db ]
With current config, for packets with IPv4 checksum errors,
errorcode is being set to UNKNOWN. Hence added a separate
errorcodes for outer and inner IPv4 checksum and changed
NPC configuration accordingly.
Also turn on L2 multicast address check in NPC protocol check block.
Fixes: 6b3321bacc ("octeontx2-af: Enable packet length and csum validation")
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 698a82ebfb ]
This patch fixes the static code analyzer reported issues
in rvu_npc.c. The reported errors are different sizes of
operands in bitops and returning uninitialized values.
Fixes: 651cd26523 ("octeontx2-af: MCAM entry installation support")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6537e96d74 ]
When the given counter does not belong to the entry
then code ends up in infinite loop because the loop
cursor, entry is not getting updated further. This
patch fixes that by updating entry for every iteration.
Fixes: a958dd59f9 ("octeontx2-af: Map or unmap NPC MCAM entry and counter")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 429205da6c ]
Based on tests the QCA7000 doesn't support checksum offloading. So assume
ip_summed is CHECKSUM_NONE and let the kernel take care of the checksum
handling. This fixes data transfer issues in noisy environments.
Reported-by: Michael Heimpold <michael.heimpold@in-tech.com>
Fixes: 291ab06ecf ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 67d6d681e1 ]
Even after commit 6457378fe7 ("ipv4: use siphash instead of Jenkins in
fnhe_hashfun()"), an attacker can still use brute force to learn
some secrets from a victim linux host.
One way to defeat these attacks is to make the max depth of the hash
table bucket a random value.
Before this patch, each bucket of the hash table used to store exceptions
could contain 6 items under attack.
After the patch, each bucket would contains a random number of items,
between 6 and 10. The attacker can no longer infer secrets.
This is slightly increasing memory size used by the hash table,
by 50% in average, we do not expect this to be a problem.
This patch is more complex than the prior one (IPv6 equivalent),
because IPv4 was reusing the oldest entry.
Since we need to be able to evict more than one entry per
update_or_create_fnhe() call, I had to replace
fnhe_oldest() with fnhe_remove_oldest().
Also note that we will queue extra kfree_rcu() calls under stress,
which hopefully wont be a too big issue.
Fixes: 4895c771c7 ("ipv4: Add FIB nexthop exceptions.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Keyu Man <kman001@ucr.edu>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reviewed-by: David Ahern <dsahern@kernel.org>
Tested-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a00df2caff ]
Even after commit 4785305c05 ("ipv6: use siphash in rt6_exception_hash()"),
an attacker can still use brute force to learn some secrets from a victim
linux host.
One way to defeat these attacks is to make the max depth of the hash
table bucket a random value.
Before this patch, each bucket of the hash table used to store exceptions
could contain 6 items under attack.
After the patch, each bucket would contains a random number of items,
between 6 and 10. The attacker can no longer infer secrets.
This is slightly increasing memory size used by the hash table,
we do not expect this to be a problem.
Following patch is dealing with the same issue in IPv4.
Fixes: 35732d01fe ("ipv6: introduce a hash table to store dst cache")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Keyu Man <kman001@ucr.edu>
Cc: Wei Wang <weiwan@google.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d745ca4f2c ]
When resuming from suspend, brcmf_pcie_pm_leave_D3 will first attempt a
hot resume and then fall back to removing the PCI device and then
reprobing. If this probe fails, the kernel will oops, because brcmf_err,
which is called to report the failure will dereference the stale bus
pointer. Open code and use the default bus-less brcmf_err to avoid this.
Fixes: 8602e62441 ("brcmfmac: pass bus to the __brcmf_err() in pcie.c")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210817063521.22450-1-a.fatoum@pengutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b63aed3ff1 ]
kmemleak reported that dev_name() of internally-handled cores were leaked
on driver unbinding. Let's use device_initialize() to take refcounts for
them and put_device() to properly free the related stuff.
While looking at it, there's another potential issue for those which should
be *registered* into driver core. If device_register() failed, we put
device once and freed bcma_device structures. In bcma_unregister_cores(),
they're treated as unregistered and we hit both UAF and double-free. That
smells not good and has also been fixed now.
Fixes: ab54bc8460 ("bcma: fill core details for every device")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210727025232.663-2-yuzenghui@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57f780f1c4 ]
Driver crashes when restoring from the Hibernate. In the resume flow,
driver need to clean up the older nic/vec objects and re-initialize them.
Fixes: 8aaa112a57 ("net: atlantic: refactoring pm logic")
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a6a723e98 ]
There is no point in calling 'free_irq()' explicitly for
'WCD9335_IRQ_SLIMBUS' in the remove function.
The irqs are requested in 'wcd9335_setup_irqs()' using a resource managed
function (i.e. 'devm_request_threaded_irq()').
'wcd9335_setup_irqs()' requests all what is defined in the 'wcd9335_irqs'
structure.
This structure has only one entry for 'WCD9335_IRQ_SLIMBUS'.
So 'devm_request...irq()' + explicit 'free_irq()' would lead to a double
free.
Remove the unneeded 'free_irq()' from the remove function.
Fixes: 20aedafdf4 ("ASoC: wcd9335: add support to wcd9335 codec")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Message-Id: <0614d63bc00edd7e81dd367504128f3d84f72efa.1629091028.git.christophe.jaillet@wanadoo.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f15a2a09c ]
If an error occurs after a successful 'clk_prepare_enable()' call, it must
be undone by a corresponding 'clk_disable_unprepare()' call.
This call is already present in the remove function.
Add this call in the error handling path and reorder the code so that the
'clk_prepare_enable()' call happens later in the function.
The goal is to have as much managed resources functions as possible
before the 'clk_prepare_enable()' call in order to keep the error handling
path simple.
While at it, remove the now unneeded 'clk' variable.
Fixes: c87dca0478 ("usb: bdc: Add clock enable for new chips with a separate BDC clock")
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/f8a4a6897deb0c8cb2e576580790303550f15fcd.1629314734.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4720f1bf4e ]
ehci_orion_drv_probe() did not account for possible errors of
clk_prepare_enable() that in particular could cause invocation of
clk_disable_unprepare() on clocks that were not prepared/enabled yet,
e.g. in remove or on handling errors of usb_add_hcd() in probe. Though,
there were several patches fixing different issues with clocks in this
driver, they did not solve this problem.
Add handling of errors of clk_prepare_enable() in ehci_orion_drv_probe()
to avoid calls of clk_disable_unprepare() without previous successful
invocation of clk_prepare_enable().
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 8c869edaee ("ARM: Orion: EHCI: Add support for enabling clocks")
Co-developed-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Link: https://lore.kernel.org/r/20210825170902.11234-1-novikov@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 661e8a88e8 ]
Iff platform_get_irq() returns 0 for the main IRQ, the driver's probe()
method will return 0 early (as if the method's call was successful).
Let's consider IRQ0 valid for simplicity -- devm_request_irq() can always
override that decision...
Fixes: 2bbd681ba2 ("i2c: xlp9xx: Driver for Netlogic XLP9XX/5XX I2C controller")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: George Cherian <george.cherian@marvell.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f980d055a0 ]
strlcpy() reads the entire source buffer first. This read may exceed the
destination size limit. This is both inefficient and can lead to linear
read overflows if a source string is not NUL-terminated.
Also, the strnlen() call does not avoid the read overflow in the strlcpy
function when a not NUL-terminated string is passed.
So, replace this block by a call to kstrndup() that avoids this type of
overflow and does the same.
Fixes: 066ce68994 ("cifs: rename cifs_strlcpy_to_host and make it use new functions")
Signed-off-by: Len Baker <len.baker@gmx.com>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7af7e497f ]
Fix a verifier bug found by smatch static checker in [0].
This problem has never been seen in prod to my best knowledge. Fixing it
still seems to be a good idea since it's hard to say for sure whether
it's possible or not to have a scenario where a combination of
convert_ctx_access() and a narrow load would lead to an out of bound
write.
When narrow load is handled, one or two new instructions are added to
insn_buf array, but before it was only checked that
cnt >= ARRAY_SIZE(insn_buf)
And it's safe to add a new instruction to insn_buf[cnt++] only once. The
second try will lead to out of bound write. And this is what can happen
if `shift` is set.
Fix it by making sure that if the BPF_RSH instruction has to be added in
addition to BPF_AND then there is enough space for two more instructions
in insn_buf.
The full report [0] is below:
kernel/bpf/verifier.c:12304 convert_ctx_accesses() warn: offset 'cnt' incremented past end of array
kernel/bpf/verifier.c:12311 convert_ctx_accesses() warn: offset 'cnt' incremented past end of array
kernel/bpf/verifier.c
12282
12283 insn->off = off & ~(size_default - 1);
12284 insn->code = BPF_LDX | BPF_MEM | size_code;
12285 }
12286
12287 target_size = 0;
12288 cnt = convert_ctx_access(type, insn, insn_buf, env->prog,
12289 &target_size);
12290 if (cnt == 0 || cnt >= ARRAY_SIZE(insn_buf) ||
^^^^^^^^^^^^^^^^^^^^^^^^^^^
Bounds check.
12291 (ctx_field_size && !target_size)) {
12292 verbose(env, "bpf verifier is misconfigured\n");
12293 return -EINVAL;
12294 }
12295
12296 if (is_narrower_load && size < target_size) {
12297 u8 shift = bpf_ctx_narrow_access_offset(
12298 off, size, size_default) * 8;
12299 if (ctx_field_size <= 4) {
12300 if (shift)
12301 insn_buf[cnt++] = BPF_ALU32_IMM(BPF_RSH,
^^^^^
increment beyond end of array
12302 insn->dst_reg,
12303 shift);
--> 12304 insn_buf[cnt++] = BPF_ALU32_IMM(BPF_AND, insn->dst_reg,
^^^^^
out of bounds write
12305 (1 << size * 8) - 1);
12306 } else {
12307 if (shift)
12308 insn_buf[cnt++] = BPF_ALU64_IMM(BPF_RSH,
12309 insn->dst_reg,
12310 shift);
12311 insn_buf[cnt++] = BPF_ALU64_IMM(BPF_AND, insn->dst_reg,
^^^^^^^^^^^^^^^
Same.
12312 (1ULL << size * 8) - 1);
12313 }
12314 }
12315
12316 new_prog = bpf_patch_insn_data(env, i + delta, insn_buf, cnt);
12317 if (!new_prog)
12318 return -ENOMEM;
12319
12320 delta += cnt - 1;
12321
12322 /* keep walking new program and skip insns we just inserted */
12323 env->prog = new_prog;
12324 insn = new_prog->insnsi + i + delta;
12325 }
12326
12327 return 0;
12328 }
[0] https://lore.kernel.org/bpf/20210817050843.GA21456@kili/
v1->v2:
- clarify that problem was only seen by static checker but not in prod;
Fixes: 46f53a65d2 ("bpf: Allow narrow loads with offset > 0")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210820163935.1902398-1-rdna@fb.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8b374b649 ]
Module configuration may differ between its instances depending on
resources required and input and output audio format. Available
parameters to select from are stored in module resource and interface
(format) lists. These come from topology, together with description of
each of pipe's modules.
Ignoring index value provided by topology and relying always on 0th
entry leads to unexpected module behavior due to under/overbudged
resources assigned or impropper format selection. Fix by taking entry at
index specified by topology.
Fixes: f6fa56e225 ("ASoC: Intel: Skylake: Parse and update module config structure")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Tested-by: Lukasz Majczak <lma@semihalf.com>
Link: https://lore.kernel.org/r/20210818075742.1515155-5-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a28dc123fa ]
Patch 96b1454f2e ("gfs2: move freeze glock outside the make_fs_rw and _ro
functions") changed the gfs2 mount sequence so that it holds the freeze
lock before calling gfs2_make_fs_rw. Before this patch, gfs2_make_fs_rw
called init_threads to initialize the quotad and logd threads. That is a
problem if the system needs to withdraw due to IO errors early in the
mount sequence, for example, while initializing the system statfs inode:
1. An IO error causes the statfs glock to not sync properly after
recovery, and leaves items on the ail list.
2. The leftover items on the ail list causes its do_xmote call to fail,
which makes it want to withdraw. But since the glock code cannot
withdraw (because the withdraw sequence uses glocks) it relies upon
the logd daemon to initiate the withdraw.
3. The withdraw can never be performed by the logd daemon because all
this takes place before the logd daemon is started.
This patch moves function init_threads from super.c to ops_fstype.c
and it changes gfs2_fill_super to start its threads before holding the
freeze lock, and if there's an error, stop its threads after releasing
it. This allows the logd to run unblocked by the freeze lock. Thus,
the logd daemon can perform its withdraw sequence properly.
Fixes: 96b1454f2e ("gfs2: move freeze glock outside the make_fs_rw and _ro functions")
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2478b9c1dc ]
Remove dev_err() messages after platform_get_irq*() failures.
drivers/i2c/busses/i2c-hix5hd2.c:417:2-9: line 417 is redundant
because platform_get_irq() already prints an error
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6840a5e37 ]
Iff platform_get_irq() returns 0, the driver's probe() method will return 0
early (as if the method's call was successful). Let's consider IRQ0 valid
for simplicity -- devm_request_irq() can always override that decision...
Fixes: e0d1ec9785 ("i2c-s3c2410: Change IRQ to be plain integer.")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a129950516 ]
When adding the code to handle platform_get_irq*() errors in the commit
489447380a ("handle errors returned by platform_get_irq*()"), the
actual error code was enforced to be -ENXIO in the driver for some
strange reason. This didn't matter much until the deferred probing was
introduced -- which requires an actual error code to be propagated
upstream from the failure site.
While fixing this, also stop overriding the errors from request_irq() to
-EIO (done since the pre-git era).
Fixes: 489447380a ("[PATCH] handle errors returned by platform_get_irq*()")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f41a4b2b5e ]
Syzbot hit "task hung" bug in hci_req_sync(). The problem was in
unreasonable huge inquiry timeout passed from userspace.
Fix it by adding sanity check for timeout value to hci_inquiry().
Since hci_inquiry() is the only user of hci_req_sync() with user
controlled timeout value, it makes sense to check timeout value in
hci_inquiry() and don't touch hci_req_sync().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-and-tested-by: syzbot+be2baed593ea56c6a84c@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1f278da6b ]
When scsi_dispatch_cmd was moved to scsi_lib.c and made static, some
compilers (i.e., at least gcc 8.4.0) decided to compile this
inline. This is a problem for lkdtm.ko, which inserted a kprobe
on this function for the SCSI_DISPATCH_CMD crashpoint.
Move this crashpoint one function up the call chain to
scsi_queue_rq. Though this is also a static function, it should never be
inlined because it is assigned as a structure entry. Therefore,
kprobe_register should always be able to find it.
Fixes: 82042a2cdb ("scsi: move scsi_dispatch_cmd to scsi_lib.c")
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kevin Mitchell <kevmitch@arista.com>
Link: https://lore.kernel.org/r/20210819022940.561875-2-kevmitch@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36ca7943ac ]
When the max pages (last_page in the swap header + 1) is smaller than
the total pages (inode size) of the swapfile, iomap_swapfile_activate
overwrites sis->max with total pages.
However, frontswap_map is a swap page state bitmap allocated using the
initial sis->max page count read from the swap header. If swapfile
activation increases sis->max, it's possible for the frontswap code to
walk off the end of the bitmap, thereby corrupting kernel memory.
[djwong: modify the description a bit; the original paragraph reads:
"However, frontswap_map is allocated using max pages. When test and clear
the sis offset, which is larger than max pages, of frontswap_map in
__frontswap_invalidate_page(), neighbors of frontswap_map may be
overwritten, i.e., slab is polluted."
Note also that this bug resulted in a behavioral change: activating a
swap file that was formatted and later extended results in all pages
being activated, not the number of pages recorded in the swap header.]
This fixes the issue by considering the limitation of max pages of swap
info in iomap_swapfile_add_extent().
To reproduce the case, compile kernel with slub RED ZONE, then run test:
$ sudo stress-ng -a 1 -x softlockup,resources -t 72h --metrics --times \
--verify -v -Y /root/tmpdir/stress-ng/stress-statistic-12.yaml \
--log-file /root/tmpdir/stress-ng/stress-logfile-12.txt \
--temp-path /root/tmpdir/stress-ng/
We'll get the error log as below:
[ 1151.015141] =============================================================================
[ 1151.016489] BUG kmalloc-16 (Not tainted): Right Redzone overwritten
[ 1151.017486] -----------------------------------------------------------------------------
[ 1151.017486]
[ 1151.018997] Disabling lock debugging due to kernel taint
[ 1151.019873] INFO: 0x0000000084e43932-0x0000000098d17cae @offset=7392. First byte 0x0 instead of 0xcc
[ 1151.021303] INFO: Allocated in __do_sys_swapon+0xcf6/0x1170 age=43417 cpu=9 pid=3816
[ 1151.022538] __slab_alloc+0xe/0x20
[ 1151.023069] __kmalloc_node+0xfd/0x4b0
[ 1151.023704] __do_sys_swapon+0xcf6/0x1170
[ 1151.024346] do_syscall_64+0x33/0x40
[ 1151.024925] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 1151.025749] INFO: Freed in put_cred_rcu+0xa1/0xc0 age=43424 cpu=3 pid=2041
[ 1151.026889] kfree+0x276/0x2b0
[ 1151.027405] put_cred_rcu+0xa1/0xc0
[ 1151.027949] rcu_do_batch+0x17d/0x410
[ 1151.028566] rcu_core+0x14e/0x2b0
[ 1151.029084] __do_softirq+0x101/0x29e
[ 1151.029645] asm_call_irq_on_stack+0x12/0x20
[ 1151.030381] do_softirq_own_stack+0x37/0x40
[ 1151.031037] do_softirq.part.15+0x2b/0x30
[ 1151.031710] __local_bh_enable_ip+0x4b/0x50
[ 1151.032412] copy_fpstate_to_sigframe+0x111/0x360
[ 1151.033197] __setup_rt_frame+0xce/0x480
[ 1151.033809] arch_do_signal+0x1a3/0x250
[ 1151.034463] exit_to_user_mode_prepare+0xcf/0x110
[ 1151.035242] syscall_exit_to_user_mode+0x27/0x190
[ 1151.035970] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 1151.036795] INFO: Slab 0x000000003b9de4dc objects=44 used=9 fp=0x00000000539e349e flags=0xfffffc0010201
[ 1151.038323] INFO: Object 0x000000004855ba01 @offset=7376 fp=0x0000000000000000
[ 1151.038323]
[ 1151.039683] Redzone 000000008d0afd3d: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc ................
[ 1151.041180] Object 000000004855ba01: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
[ 1151.042714] Redzone 0000000084e43932: 00 00 00 c0 cc cc cc cc ........
[ 1151.044120] Padding 000000000864c042: 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZZZZZZZZZ
[ 1151.045615] CPU: 5 PID: 3816 Comm: stress-ng Tainted: G B 5.10.50+ #7
[ 1151.046846] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
[ 1151.048633] Call Trace:
[ 1151.049072] dump_stack+0x57/0x6a
[ 1151.049585] check_bytes_and_report+0xed/0x110
[ 1151.050320] check_object+0x1eb/0x290
[ 1151.050924] ? __x64_sys_swapoff+0x39a/0x540
[ 1151.051646] free_debug_processing+0x151/0x350
[ 1151.052333] __slab_free+0x21a/0x3a0
[ 1151.052938] ? _cond_resched+0x2d/0x40
[ 1151.053529] ? __vunmap+0x1de/0x220
[ 1151.054139] ? __x64_sys_swapoff+0x39a/0x540
[ 1151.054796] ? kfree+0x276/0x2b0
[ 1151.055307] kfree+0x276/0x2b0
[ 1151.055832] __x64_sys_swapoff+0x39a/0x540
[ 1151.056466] do_syscall_64+0x33/0x40
[ 1151.057084] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 1151.057866] RIP: 0033:0x150340b0ffb7
[ 1151.058481] Code: Unable to access opcode bytes at RIP 0x150340b0ff8d.
[ 1151.059537] RSP: 002b:00007fff7f4ee238 EFLAGS: 00000246 ORIG_RAX: 00000000000000a8
[ 1151.060768] RAX: ffffffffffffffda RBX: 00007fff7f4ee66c RCX: 0000150340b0ffb7
[ 1151.061904] RDX: 000000000000000a RSI: 0000000000018094 RDI: 00007fff7f4ee860
[ 1151.063033] RBP: 00007fff7f4ef980 R08: 0000000000000000 R09: 0000150340a672bd
[ 1151.064135] R10: 00007fff7f4edca0 R11: 0000000000000246 R12: 0000000000018094
[ 1151.065253] R13: 0000000000000005 R14: 000000000160d930 R15: 00007fff7f4ee66c
[ 1151.066413] FIX kmalloc-16: Restoring 0x0000000084e43932-0x0000000098d17cae=0xcc
[ 1151.066413]
[ 1151.067890] FIX kmalloc-16: Object at 0x000000004855ba01 not freed
Fixes: 67482129cd ("iomap: add a swapfile activation function")
Fixes: a45c0eccc5 ("iomap: move the swapfile code into a separate file")
Signed-off-by: Gang Deng <gavin.dg@linux.alibaba.com>
Signed-off-by: Xu Yu <xuyu@linux.alibaba.com>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2af0c5ffad ]
If IRQ occurs between calling request_irq() and mv_u3d_eps_init(),
then null pointer dereference occurs since u3d->eps[] wasn't
initialized yet but used in mv_u3d_nuke().
The patch puts registration of the interrupt handler after
initializing of neccesery data.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 90fccb529d ("usb: gadget: Gadget directory cleanup - group UDC drivers")
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Link: https://lore.kernel.org/r/20210818141247.4794-1-lutovinova@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e7c57355a ]
When unbinding the firmware device we need to make sure it has no
consumers left. Otherwise we'd leave them with a firmware handle
pointing at freed memory.
Keep a reference count of all consumers and introduce rpi_firmware_put()
which will permit automatically decrease the reference count upon
unbinding consumer drivers.
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d744da241 ]
The driver overrides the error codes returned by platform_get_irq() to
-ENODEV, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the
error codes upstream.
Fixes: 0d676a6c43 ("i2c: add support for Socionext SynQuacer I2C controller")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbfa6f33e3 ]
Commit 0a0a66c984 ("clk: staging: Specify IOMEM dependency for Xilinx
Clocking Wizard driver") introduces a dependency on the non-existing config
IOMEM, which basically makes it impossible to include this driver into any
build. Fortunately, ./scripts/checkkconfigsymbols.py warns:
IOMEM
Referencing files: drivers/staging/clocking-wizard/Kconfig
The config for IOMEM support is called HAS_IOMEM. Correct this reference to
the intended config.
Fixes: 0a0a66c984 ("clk: staging: Specify IOMEM dependency for Xilinx Clocking Wizard driver")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20210817105404.13146-1-lukas.bulwahn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 514ef1e62d ]
Current PCIe MEM space of size 16 MB is not enough for some combination
of PCIe cards (e.g. NVMe disk together with ath11k wifi card). ARM Trusted
Firmware for Armada 3700 platform already assigns 128 MB for PCIe window,
so extend PCIe MEM space to the end of 128 MB PCIe window which allows to
allocate more PCIe BARs for more PCIe cards.
Without this change some combination of PCIe cards cannot be used and
kernel show error messages in dmesg during initialization:
pci 0000:00:00.0: BAR 8: no space for [mem size 0x01800000]
pci 0000:00:00.0: BAR 8: failed to assign [mem size 0x01800000]
pci 0000:00:00.0: BAR 6: assigned [mem 0xe8000000-0xe80007ff pref]
pci 0000:01:00.0: BAR 8: no space for [mem size 0x01800000]
pci 0000:01:00.0: BAR 8: failed to assign [mem size 0x01800000]
pci 0000:02:03.0: BAR 8: no space for [mem size 0x01000000]
pci 0000:02:03.0: BAR 8: failed to assign [mem size 0x01000000]
pci 0000:02:07.0: BAR 8: no space for [mem size 0x00100000]
pci 0000:02:07.0: BAR 8: failed to assign [mem size 0x00100000]
pci 0000:03:00.0: BAR 0: no space for [mem size 0x01000000 64bit]
pci 0000:03:00.0: BAR 0: failed to assign [mem size 0x01000000 64bit]
Due to bugs in U-Boot port for Turris Mox, the second range in Turris Mox
kernel DTS file for PCIe must start at 16 MB offset. Otherwise U-Boot
crashes during loading of kernel DTB file. This bug is present only in
U-Boot code for Turris Mox and therefore other Armada 3700 devices are not
affected by this bug. Bug is fixed in U-Boot version 2021.07.
To not break booting new kernels on existing versions of U-Boot on Turris
Mox, use first 16 MB range for IO and second range with rest of PCIe window
for MEM.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 76f6386b25 ("arm64: dts: marvell: Add Aardvark PCIe support for Armada 3700")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7104cc1a9 ]
This should use the network-namespace-wide client_lock, not the
per-client cl_lock.
You shouldn't see any bugs unless you're actually using the
forced-expiry interface introduced by 89c905becc.
Fixes: 89c905becc "nfsd: allow forced expiration of NFSv4 clients"
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd2d644ddb ]
After calling vfs_test_lock() the pointer to a conflicting lock can be
returned, and that lock is not guarunteed to be owned by nlm. In that
case, we cannot cast it to struct nlm_lockowner. Instead return the pid
of that conflicting lock.
Fixes: 646d73e91b ("lockd: Show pid of lockd for remote locks")
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8bbd97ad0 ]
If CONFIG_DEBUG_LOCK_ALLOC=y is enabled then local_lock_t has an 'owner'
member which is checked for consistency, but nothing initialized it to
zero explicitly.
The static initializer does so implicit, and the run time allocated per CPU
storage is usually zero initialized as well, but relying on that is not
really good practice.
Fixes: 91710728d1 ("locking: Introduce local_lock()")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20210815211301.969975279@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dfd5e3f5fe ]
The local_lock_t's are special, because they cannot form IRQ
inversions, make sure we can tell them apart from the rest of the
locks.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d45a1373e ]
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to request_threaded_irq() (which
takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding an
original error code. Stop calling request_threaded_irq() with the invalid
IRQ #s.
Fixes: 9ba96ae507 ("usb: omap1: Tahvo USB transceiver driver")
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/8280d6a4-8e9a-7cfe-1aa9-db586dc9afdf@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2f6662ac0 ]
Invoking atomic_notifier_chain_notify() requires acquiring a spinlock_t,
which can block under CONFIG_PREEMPT_RT. Notifications for members of the
cpu_pm notification chain will be issued by the idle task, which can never
block.
Making *all* atomic_notifiers use a raw_spinlock is too big of a hammer, as
only notifications issued by the idle task are problematic.
Special-case cpu_pm_notifier_chain by kludging a raw_notifier and
raw_spinlock_t together, matching the atomic_notifier behavior with a
raw_spinlock_t.
Fixes: 70d9329857 ("notifier: Fix broken error handling pattern")
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ea53674d0 ]
Commit 0ea9fd001a ("Bluetooth: Shutdown controller after workqueues
are flushed or cancelled") introduced a regression that makes mtkbtsdio
driver stops working:
[ 36.593956] Bluetooth: hci0: Firmware already downloaded
[ 46.814613] Bluetooth: hci0: Execution of wmt command timed out
[ 46.814619] Bluetooth: hci0: Failed to send wmt func ctrl (-110)
The shutdown callback depends on the result of hdev->rx_work, so we
should call it before flushing rx_work:
-> btmtksdio_shutdown()
-> mtk_hci_wmt_sync()
-> __hci_cmd_send()
-> wait for BTMTKSDIO_TX_WAIT_VND_EVT gets cleared
-> btmtksdio_recv_event()
-> hci_recv_frame()
-> queue_work(hdev->workqueue, &hdev->rx_work)
-> clears BTMTKSDIO_TX_WAIT_VND_EVT
So move the shutdown callback before flushing TX/RX queue to resolve the
issue.
Reported-and-tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Fixes: 0ea9fd001a ("Bluetooth: Shutdown controller after workqueues are flushed or cancelled")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f0c4f1b72 ]
Currently, "sample04" and "sample05" are not working properly when
running with an IPv6 option("-6"). The commit 0f06a6787e ("samples:
Add an IPv6 "-6" option to the pktgen scripts") has omitted the addition
of this option at "sample04" and "sample05".
In order to support IPv6 option, this commit adds logic related to IPv6
option.
Fixes: 0f06a6787e ("samples: Add an IPv6 "-6" option to the pktgen scripts")
Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed43fbac71 ]
The { 0 } doesn't clear all fields in the struct, but tells to the
compiler to set all fields to zero and doesn't touch any sub-fields
if they exists.
The {} is an empty initialiser that instructs to fully initialize whole
struct including sub-fields, which is error-prone for future
devlink_flash_notify extensions.
Fixes: 6700acc5f1 ("devlink: collect flash notify params into a struct")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d164dd9a5c ]
The "probed" part of test_core_autosize copies an integer using
bpf_core_read() into an integer of a potentially different size.
On big-endian machines a destination offset is required for this to
produce a sensible result.
Fixes: 888d83b961 ("selftests/bpf: Validate libbpf's auto-sizing of LD/ST/STX instructions")
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210812224814.187460-1-iii@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cea45a3bd2 ]
soc_device_match() is intended as a last resort, to handle e.g. quirks
that cannot be handled by matching based on a compatible value.
As the device nodes for the Renesas USB 3.0 Peripheral Controller on
R-Car E3 and RZ/G2E do have SoC-specific compatible values, the latter
can and should be used to match against these devices.
This also fixes support for the USB 3.0 Peripheral Controller on the
R-Car E3e (R8A779M6) SoC, which is a different grading of the R-Car E3
(R8A77990) SoC, using the same SoC-specific compatible value.
Fixes: 30025efa8b ("usb: gadget: udc: renesas_usb3: add support for r8a77990")
Fixes: 546970fdab ("usb: gadget: udc: renesas_usb3: add support for r8a774c0")
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/760981fb4cd110d7cbfc9dcffa365e7c8b25c6e5.1628696960.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0881e22c06 ]
The driver neglects to check the result of platform_get_irq()'s calls and
blithely passes the negative error codes to request_threaded_irq() (which
takes *unsigned* IRQ #), causing them both to fail with -EINVAL, overriding
an original error code. Stop calling request_threaded_irq() with the
invalid IRQ #s.
Fixes: c33fad0c37 ("usb: otg: Adding twl6030-usb transceiver driver for OMAP4430")
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/9507f50b-50f1-6dc4-f57c-3ed4e53a1c25@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ecc2f30dbb ]
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to request_irq() (which takes
*unsigned* IRQ #), causing it to fail with -EINVAL, overriding an original
error code. Stop calling request_irq() with the invalid IRQ #s.
Fixes: 0807c500a1 ("USB: add Freescale USB OTG Transceiver driver")
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/b0a86089-8b8b-122e-fd6d-73e8c2304964@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50855c3157 ]
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_irq() (which takes
*unsigned* IRQ #), causing it to fail with -EINVAL, overriding an original
error code. Stop calling devm_request_irq() with the invalid IRQ #s.
Fixes: 8b2e76687b ("USB: AT91 UDC updates, mostly power management")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Acked-by: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/6654a224-739a-1a80-12f0-76d920f87b6c@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1750069567 ]
In dwc3_qcom_acpi_register_core(), the driver neglects to check the result
of platform_get_irq()'s call and blithely assigns the negative error codes
to the allocated child device's IRQ resource and then passing this resource
to platform_device_add_resources() and later causing dwc3_otg_get_irq() to
fail anyway. Stop calling platform_device_add_resources() with the invalid
IRQ #s, so that there's less complexity in the IRQ error checking.
Fixes: 2bc02355f8 ("usb: dwc3: qcom: Add support for booting with ACPI")
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/45fec3da-1679-5bfe-5d74-219ca3fb28e7@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 772d44526e ]
When I booted up on a board that had a slightly different codec
stuffed on it, I got this message at bootup:
rt5682 9-001a: Device with ID register 6749 is not rt5682
That's normal/expected, but what wasn't normal was the splat that I
got after:
WARNING: CPU: 7 PID: 176 at drivers/regulator/core.c:2151 _regulator_put+0x150/0x158
pc : _regulator_put+0x150/0x158
...
Call trace:
_regulator_put+0x150/0x158
regulator_bulk_free+0x48/0x70
devm_regulator_bulk_release+0x20/0x2c
release_nodes+0x1cc/0x244
devres_release_all+0x44/0x60
really_probe+0x17c/0x378
...
This is because the error paths don't turn off the regulator. Let's
fix that.
Fixes: 0ddce71c21 ("ASoC: rt5682: add rt5682 codec driver")
Fixes: 87b42abae9 ("ASoC: rt5682: Implement remove callback")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210811081751.v2.1.I4a1d9aa5d99e05aeee15c2768db600158d76cab8@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6977cc89c8 ]
'of_find_device_by_node()' takes a reference that must be released when
not needed anymore.
This is expected to be done in 'dsi_destroy()'.
However, there are 2 issues in 'dsi_get_phy()'.
First, if 'of_find_device_by_node()' succeeds but 'platform_get_drvdata()'
returns NULL, 'msm_dsi->phy_dev' will still be NULL, and the reference
won't be released in 'dsi_destroy()'.
Secondly, as 'of_find_device_by_node()' already takes a reference, there is
no need for an additional 'get_device()'.
Move the assignment to 'msm_dsi->phy_dev' a few lines above and remove the
unneeded 'get_device()' to solve both issues.
Fixes: ec31abf668 ("drm/msm/dsi: Separate PHY to another platform device")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/f15bc57648a00e7c99f943903468a04639d50596.1628241097.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1dee2c1de ]
In commit 4e1a720d03 ("Bluetooth: avoid killing an already killed
socket"), a check was added to sco_sock_kill to skip killing a socket
if the SOCK_DEAD flag was set.
This was done after a trace for a use-after-free bug showed that the
same sock pointer was being killed twice.
Unfortunately, this check prevents sco_sock_kill from running on any
socket. sco_sock_kill kills a socket only if it's zapped and orphaned,
however sock_orphan announces that the socket is dead before detaching
it. i.e., orphaned sockets have the SOCK_DEAD flag set.
To fix this, we remove the check for SOCK_DEAD, and avoid repeated
calls to sco_sock_kill by removing incorrect calls in:
1. sco_sock_timeout. The socket should not be killed on timeout as
further processing is expected to be done. For example,
sco_sock_connect sets the timer then waits for the socket to be
connected or for an error to be returned.
2. sco_conn_del. This function should clean up resources for the
connection, but the socket itself should be cleaned up in
sco_sock_release.
3. sco_sock_close. Calls to sco_sock_close in sco_sock_cleanup_listen
and sco_sock_release are followed by sco_sock_kill. Hence the
duplicated call should be removed.
Fixes: 4e1a720d03 ("Bluetooth: avoid killing an already killed socket")
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4eeaed04e ]
Sparse warnings triggered truncating the IDs of some platform device
tables. Unfortunately some of the IDs in the match tables were missed
which breaks audio. The KBL change has been verified to fix audio, the
CML change was not tested as it was found through grepping the broken
changes and found to match the same situation in anticipation that it
should also be fixed.
Fixes: 94efd726b9 ("ASoC: Intel: kbl_da7219_max98357a: shrink platform_id below 20 characters")
Fixes: 24e46fb811 ("ASoC: Intel: bxt_da7219_max98357a: shrink platform_id below 20 characters")
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Tested-by: Matt Davis <mattedavis@google.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210809213544.1682444-1-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ba34d3c73 ]
The cpuset fields that manage partition root state do not strictly
follow the cpuset locking rule that update to cpuset has to be done
with both the callback_lock and cpuset_mutex held. This is now fixed
by making sure that the locking rule is upheld.
Fixes: 3881b86128 ("cpuset: Add an error state to cpuset.sched.partition")
Fixes: 4b842da276 ("cpuset: Make CPU hotplug work with partition")
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f3adb8a1e ]
Use more descriptive variable names for update_prstate(), remove
unnecessary code and fix some typos. There is no functional change.
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7fcc17d0cb ]
The Energy Model (EM) provides useful information about device power in
each performance state to other subsystems like: Energy Aware Scheduler
(EAS). The energy calculation in EAS does arithmetic operation based on
the EM em_cpu_energy(). Current implementation of that function uses
em_perf_state::cost as a pre-computed cost coefficient equal to:
cost = power * max_frequency / frequency.
The 'power' is expressed in milli-Watts (or in abstract scale).
There are corner cases when the EAS energy calculation for two Performance
Domains (PDs) return the same value. The EAS compares these values to
choose smaller one. It might happen that this values are equal due to
rounding error. In such scenario, we need better resolution, e.g. 1000
times better. To provide this possibility increase the resolution in the
em_perf_state::cost for 64-bit architectures. The cost of increasing
resolution on 32-bit is pretty high (64-bit division) and is not justified
since there are no new 32bit big.LITTLE EAS systems expected which would
benefit from this higher resolution.
This patch allows to avoid the rounding to milli-Watt errors, which might
occur in EAS energy estimation for each PD. The rounding error is common
for small tasks which have small utilization value.
There are two places in the code where it makes a difference:
1. In the find_energy_efficient_cpu() where we are searching for
best_delta. We might suffer there when two PDs return the same result,
like in the example below.
Scenario:
Low utilized system e.g. ~200 sum_util for PD0 and ~220 for PD1. There
are quite a few small tasks ~10-15 util. These tasks would suffer for
the rounding error. These utilization values are typical when running games
on Android. One of our partners has reported 5..10mA less battery drain
when running with increased resolution.
Some details:
We have two PDs: PD0 (big) and PD1 (little)
Let's compare w/o patch set ('old') and w/ patch set ('new')
We are comparing energy w/ task and w/o task placed in the PDs
a) 'old' w/o patch set, PD0
task_util = 13
cost = 480
sum_util_w/o_task = 215
sum_util_w_task = 228
scale_cpu = 1024
energy_w/o_task = 480 * 215 / 1024 = 100.78 => 100
energy_w_task = 480 * 228 / 1024 = 106.87 => 106
energy_diff = 106 - 100 = 6
(this is equal to 'old' PD1's energy_diff in 'c)')
b) 'new' w/ patch set, PD0
task_util = 13
cost = 480 * 1000 = 480000
sum_util_w/o_task = 215
sum_util_w_task = 228
energy_w/o_task = 480000 * 215 / 1024 = 100781
energy_w_task = 480000 * 228 / 1024 = 106875
energy_diff = 106875 - 100781 = 6094
(this is not equal to 'new' PD1's energy_diff in 'd)')
c) 'old' w/o patch set, PD1
task_util = 13
cost = 160
sum_util_w/o_task = 283
sum_util_w_task = 293
scale_cpu = 355
energy_w/o_task = 160 * 283 / 355 = 127.55 => 127
energy_w_task = 160 * 296 / 355 = 133.41 => 133
energy_diff = 133 - 127 = 6
(this is equal to 'old' PD0's energy_diff in 'a)')
d) 'new' w/ patch set, PD1
task_util = 13
cost = 160 * 1000 = 160000
sum_util_w/o_task = 283
sum_util_w_task = 293
scale_cpu = 355
energy_w/o_task = 160000 * 283 / 355 = 127549
energy_w_task = 160000 * 296 / 355 = 133408
energy_diff = 133408 - 127549 = 5859
(this is not equal to 'new' PD0's energy_diff in 'b)')
2. Difference in the 6% energy margin filter at the end of
find_energy_efficient_cpu(). With this patch the margin comparison also
has better resolution, so it's possible to have better task placement
thanks to that.
Fixes: 27871f7a8a ("PM: Introduce an Energy Model management framework")
Reported-by: CCJ Yeh <CCj.Yeh@mediatek.com>
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 713baf3dae ]
An earlier commit replaced using batostr to using %pMR sprintf for the
construction of session->name. Static analysis detected that this new
method can use a total of 21 characters (including the trailing '\0')
so we need to increase the BTNAMSIZ from 18 to 21 to fix potential
buffer overflows.
Addresses-Coverity: ("Out-of-bounds write")
Fixes: fcb73338ed ("Bluetooth: Use %pMR in sprintf/seq_printf instead of batostr")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 112cedc8e6 ]
If a kernel module gets unloaded then it printed report about a leak before
commit 275678e7a9 ("debugfs: Check module state before warning in
{full/open}_proxy_open()"). An additional check was added in this commit to
avoid this printing. But it was forgotten that the function must return an
error in this case because it was not actually opened.
As result, the systems started to crash or to hang when a module was
unloaded while something was trying to open a file.
Fixes: 275678e7a9 ("debugfs: Check module state before warning in {full/open}_proxy_open()")
Cc: Taehee Yoo <ap420073@gmail.com>
Reported-by: Mário Lopes <ml@simonwunderlich.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Link: https://lore.kernel.org/r/20210802162444.7848-1-sven@narfation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3d4571955 ]
The SMSM driver detects interrupt edges by tracking the last state
it has seen (and has triggered the interrupt handler for). This works
fine, but only if the interrupt does not change state while masked.
For example, if an interrupt is unmasked while the state is HIGH,
the stored last_value for that interrupt might still be LOW. Then,
when the remote processor triggers smsm_intr() we assume that nothing
has changed, even though the state might have changed from HIGH to LOW.
Attempt to fix this by checking the current remote state before
unmasking an IRQ. Use atomic operations to avoid the interrupt handler
from interfering with the unmask function.
This fixes modem crashes in some edge cases with the BAM-DMUX driver.
Specifically, the BAM-DMUX interrupt handler is not called for the
HIGH -> LOW smsm state transition if the BAM-DMUX driver is loaded
(and therefore unmasks the interrupt) after the modem was already started:
qcom-q6v5-mss 4080000.remoteproc: fatal error received: a2_task.c:3188:
Assert FALSE failed: A2 DL PER deadlock timer expired waiting for Apps ACK
Fixes: c97c4090ff ("soc: qcom: smsm: Add driver for Qualcomm SMSM")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210712135703.324748-2-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e00392a89 ]
PME signaling is only enabled by __pci_enable_wake() if the target
device can signal PME from the given target power state (to avoid
pointless reconfiguration of the device), but if the hierarchy above
the device goes into D3cold, the device itself will end up in D3cold
too, so if it can signal PME from D3cold, it should be enabled to
do so in __pci_enable_wake().
[Note that if the device does not end up in D3cold and it cannot
signal PME from the original target power state, it will not signal
PME, so in that case the behavior does not change.]
Link: https://lore.kernel.org/linux-pm/3149540.aeNJFYEL58@kreacher/
Fixes: 5bcc2fb4e8 ("PCI PM: Simplify PCI wake-up code")
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reported-by: Utkarsh H Patel <utkarsh.h.patel@intel.com>
Reported-by: Koba Ko <koba.ko@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da9f215068 ]
It is inconsistent to return PCI_D0 from pci_target_state() instead
of the original target state if 'wakeup' is true and the device
cannot signal PME from D0.
This only happens when the device cannot signal PME from the original
target state and any shallower power states (including D0) and that
case is effectively equivalent to the one in which PME singaling is
not supported at all. Since the original target state is returned in
the latter case, make the function do that in the former one too.
Link: https://lore.kernel.org/linux-pm/3149540.aeNJFYEL58@kreacher/
Fixes: 666ff6f83e ("PCI/PM: Avoid using device_may_wakeup() for runtime PM")
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reported-by: Utkarsh H Patel <utkarsh.h.patel@intel.com>
Reported-by: Koba Ko <koba.ko@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09ea9719a4 ]
Currently the call to find_format can potentially return a NULL to
fmt and the nullpointer is later dereferenced on the assignment of
pixmp->num_planes = fmt->num_planes. Fix this by adding a NULL pointer
check and returning NULL for the failure case.
Addresses-Coverity: ("Dereference null return")
Fixes: aaaa93eda6 ("[media] media: venus: venc: add video encoder files")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6fa54bc713 ]
If em28xx_ir_init fails, it would decrease the refcount of dev. However,
in the em28xx_ir_fini, when ir is NULL, it goes to ref_put and decrease
the refcount of dev. This will lead to a refcount bug.
Fix this bug by removing the kref_put in the error handling code
of em28xx_ir_init.
refcount_t: underflow; use-after-free.
WARNING: CPU: 0 PID: 7 at lib/refcount.c:28 refcount_warn_saturate+0x18e/0x1a0 lib/refcount.c:28
Modules linked in:
CPU: 0 PID: 7 Comm: kworker/0:1 Not tainted 5.13.0 #3
Workqueue: usb_hub_wq hub_event
RIP: 0010:refcount_warn_saturate+0x18e/0x1a0 lib/refcount.c:28
Call Trace:
kref_put.constprop.0+0x60/0x85 include/linux/kref.h:69
em28xx_usb_disconnect.cold+0xd7/0xdc drivers/media/usb/em28xx/em28xx-cards.c:4150
usb_unbind_interface+0xbf/0x3a0 drivers/usb/core/driver.c:458
__device_release_driver drivers/base/dd.c:1201 [inline]
device_release_driver_internal+0x22a/0x230 drivers/base/dd.c:1232
bus_remove_device+0x108/0x160 drivers/base/bus.c:529
device_del+0x1fe/0x510 drivers/base/core.c:3540
usb_disable_device+0xd1/0x1d0 drivers/usb/core/message.c:1419
usb_disconnect+0x109/0x330 drivers/usb/core/hub.c:2221
hub_port_connect drivers/usb/core/hub.c:5151 [inline]
hub_port_connect_change drivers/usb/core/hub.c:5440 [inline]
port_event drivers/usb/core/hub.c:5586 [inline]
hub_event+0xf81/0x1d40 drivers/usb/core/hub.c:5668
process_one_work+0x2c9/0x610 kernel/workqueue.c:2276
process_scheduled_works kernel/workqueue.c:2338 [inline]
worker_thread+0x333/0x5b0 kernel/workqueue.c:2424
kthread+0x188/0x1d0 kernel/kthread.c:319
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:295
Reported-by: Dongliang Mu <mudongliangabcd@gmail.com>
Fixes: ac56886371 ("media: em28xx: Fix possible memory leak of em28xx struct")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64f67b5240 ]
Some 2-in-1s with a detachable (USB) keyboard(dock) have mute-LEDs in
the speaker- and/or mic-mute keys on the keyboard.
Examples of this are the Lenovo Thinkpad10 tablet (with its USB kbd-dock)
and the HP x2 10 series.
The detachable nature of these keyboards means that the keyboard and
thus the mute LEDs may show up after the user (or userspace restoring
old mixer settings) has muted the speaker and/or mic.
Current LED-class devices with a default_trigger of "audio-mute" or
"audio-micmute" initialize the brightness member of led_classdev with
ledtrig_audio_get() before registering the LED.
This makes the software state after attaching the keyboard match the
actual audio mute state, e.g. cat /sys/class/leds/foo/brightness will
show the right value.
But before this commit nothing was actually calling the led_classdev's
brightness_set[_blocking] callback so the value returned by
ledtrig_audio_get() was never actually being sent to the hw, leading
to the mute LEDs staying in their default power-on state, after
attaching the keyboard, even if ledtrig_audio_get() returned a different
state.
This could be fixed by having the individual LED drivers call
brightness_set[_blocking] themselves after registering the LED,
but this really is something which should be done by a led-trigger
activate callback.
Add an activate callback for this, fixing the issue of the
mute LEDs being out of sync after (re)attaching the keyboard.
Cc: Takashi Iwai <tiwai@suse.de>
Fixes: faa2541f5b ("leds: trigger: Introduce audio mute LED trigger")
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e1baaaa24 ]
device_get_next_child_node() bumps a reference counting of a returned variable.
We have to balance it whenever we return to the caller.
Fixes: 8cd7d6daba ("leds: lt3593: Add device tree probing glue")
Cc: Daniel Mack <daniel@zonque.org>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f16a3bb69a ]
The driver is written as if platform_get_irq() returns 0 on errors (while
actually it returns a negative error code), blithely passing these error
codes to request_irq() (which takes *unsigned* IRQ #) -- which fails with
-EINVAL. Add the necessary error check to the pre-existing *if* statement
forcing the driver into the polling mode...
Fixes: 4ad48e6ab1 ("i2c: Renesas Highlander FPGA SMBus support")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c96ca5604a ]
Hihope boards use Realtek PHY. From the very beginning it use only
tx delays. However the phy driver commit bbc4d71d63
("net: phy: realtek: fix rtl8211e rx/tx delay config") introduced
NFS mount failure. Now it needs rx delay inaddition to tx delay
for NFS mount to work. This patch fixes NFS mount failure issue
by adding MAC internal rx delay.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Fixes: bbc4d71d63 ("net: phy: realtek: fix rtl8211e rx/tx delay config")
Link: https://lore.kernel.org/r/20210721180632.15080-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5200e63af ]
Some EtherAVB variants support internal clock delay configuration, which
can add larger delays than the delays that are typically supported by
the PHY (using an "rgmii-*id" PHY mode, and/or "[rt]xc-skew-ps"
properties).
Historically, the EtherAVB driver configured these delays based on the
"rgmii-*id" PHY mode. This was wrong, as these are meant solely for the
PHY, not for the MAC. Hence properties were introduced for explicit
configuration of these delays.
Convert the RZ/G2 DTS files from the old to the new scheme:
- Add default "rx-internal-delay-ps" and "tx-internal-delay-ps"
properties to the SoC .dtsi files, to be overridden by board files
where needed,
- Convert board files from "rgmii-*id" PHY modes to "rgmii", adding
the appropriate "rx-internal-delay-ps" and/or "tx-internal-delay-ps"
overrides.
Notes:
- RZ/G2E does not support TX internal delay handling.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200819134344.27813-8-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a25fca4d3c ]
This patch fixes the MGMT add_advertising command repsones with the
wrong opcode when it is trying to return the not supported error.
Fixes: cbbdfa6f33 ("Bluetooth: Enable controller RPA resolution using Experimental feature")
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ca34a13f7 ]
Syzbot reported warning in netlbl_cipsov4_add(). The
problem was in too big doi_def->map.std->lvl.local_size
passed to kcalloc(). Since this value comes from userpace there is
no need to warn if value is not correct.
The same problem may occur with other kcalloc() calls in
this function, so, I've added __GFP_NOWARN flag to all
kcalloc() calls there.
Reported-and-tested-by: syzbot+cdd51ee2e6b0b2e18c0d@syzkaller.appspotmail.com
Fixes: 96cb8e3313 ("[NetLabel]: CIPSOv4 and Unlabeled packet integration")
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c9856e4ed ]
There is some sort of corner case behavior of the controller,
which could rarely be triggered at least on i.MX6SX connected
to 800x480 DPI panel and i.MX8MM connected to DPI->DSI->LVDS
bridged 1920x1080 panel (and likely on other setups too), where
the image on the panel shifts to the right and wraps around.
This happens either when the controller is enabled on boot or
even later during run time. The condition does not correct
itself automatically, i.e. the display image remains shifted.
It seems this problem is known and is due to sporadic underflows
of the LCDIF FIFO. While the LCDIF IP does have underflow/overflow
IRQs, neither of the IRQs trigger and neither IRQ status bit is
asserted when this condition occurs.
All known revisions of the LCDIF IP have CTRL1 RECOVER_ON_UNDERFLOW
bit, which is described in the reference manual since i.MX23 as
"
Set this bit to enable the LCDIF block to recover in the next
field/frame if there was an underflow in the current field/frame.
"
Enable this bit to mitigate the sporadic underflows.
Fixes: 45d59d7040 ("drm: Add new driver for MXSFB controller")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Abrecht <public@danielabrecht.ch>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Stefan Agner <stefan@agner.ch>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210620224701.189289-1-marex@denx.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15d428e6fe ]
In cpuset_hotplug_workfn(), the detection of whether the cpu list
has been changed is done by comparing the effective cpus of the top
cpuset with the cpu_active_mask. However, in the rare case that just
all the CPUs in the subparts_cpus are offlined, the detection fails
and the partition states are not updated correctly. Fix it by forcing
the cpus_updated flag to true in this particular case.
Fixes: 4b842da276 ("cpuset: Make CPU hotplug work with partition")
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26ab7b3845 ]
This commit does a cleanup in LRO configuration.
LRO is a parameter of an RQ, but its state is changed by modifying a TIR
related to the RQ.
The current status: LRO for tunneled packets is not supported in the
driver, inner TIRs may enable LRO on creation, but LRO status of inner
TIRs isn't changed in mlx5e_modify_tirs_lro(). This is inconsistent, but
as long as the firmware doesn't declare support for tunneled LRO, it
works, because the same RQs are shared between the inner and outer TIRs.
This commit does two fixes:
1. If the firmware has the tunneled LRO capability, LRO is blocked
altogether, because it's not possible to block it for inner TIRs only,
when the same RQs are shared between inner and outer TIRs, and the
driver won't be able to handle tunneled LRO traffic.
2. mlx5e_modify_tirs_lro() is patched to modify LRO state for all TIRs,
including inner ones, because all TIRs related to an RQ should agree on
their LRO state.
Fixes: 7b3722fa9e ("net/mlx5e: Support RSS for GRE tunneled packets")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c43f3865c ]
TIR's rx_hash_field_selector_inner can be enabled only when
tunneled_offload_en = 1. tunneled_offload_en is filled according to the
tunneled_offload_en field in struct mlx5e_params, which is false in the
IPoIB profile. On the other hand, the IPoIB profile passes inner_ttc =
true to mlx5e_create_indirect_tirs, which potentially allows the latter
function to attempt to create inner indirect TIRs without having
tunneled_offload_en set.
This commit prohibits this behavior by passing inner_ttc = false to
mlx5e_create_indirect_tirs. The latter function won't attempt to create
inner indirect TIRs.
As inner indirect TIRs are not created in the IPoIB profile (this commit
blocks it explicitly, and even before they would have failed to be
created), the call to mlx5e_create_inner_ttc_table in
mlx5i_create_flow_steering is a no-op and can be removed.
Fixes: 46dc933cee ("net/mlx5e: Provide explicit directive if to create inner indirect tirs")
Fixes: 458821c72b ("net/mlx5e: IPoIB, Add inner TTC table to IPoIB flow steering")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72ccc373b0 ]
After enabling CONFIG_REGULATOR_DEBUG=y we observer below debug logs.
Changes help link VCCK and VDDEE pwm regulator to 5V regulator supply
instead of dummy regulator.
[ 7.117140] pwm-regulator regulator-vcck: Looking up pwm-supply from device tree
[ 7.117153] pwm-regulator regulator-vcck: Looking up pwm-supply property in node /regulator-vcck failed
[ 7.117184] VCCK: supplied by regulator-dummy
[ 7.117194] regulator-dummy: could not add device link regulator.8: -ENOENT
[ 7.117266] VCCK: 860 <--> 1140 mV at 986 mV, enabled
[ 7.118498] VDDEE: will resolve supply early: pwm
[ 7.118515] pwm-regulator regulator-vddee: Looking up pwm-supply from device tree
[ 7.118526] pwm-regulator regulator-vddee: Looking up pwm-supply property in node /regulator-vddee failed
[ 7.118553] VDDEE: supplied by regulator-dummy
[ 7.118563] regulator-dummy: could not add device link regulator.9: -ENOENT
Fixes: 087a1d8b4e ("ARM: dts: meson8b: ec100: add the VDDEE regulator")
Fixes: 3e7db1c1b7 ("ARM: dts: meson8b: ec100: improve the description of the regulators")
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210705112358.3554-4-linux.amoon@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 876228e9f9 ]
After enabling CONFIG_REGULATOR_DEBUG=y we observe below debug logs.
Changes help link VCCK and VDDEE pwm regulator to 5V regulator supply
instead of dummy regulator.
[ 7.117140] pwm-regulator regulator-vcck: Looking up pwm-supply from device tree
[ 7.117153] pwm-regulator regulator-vcck: Looking up pwm-supply property in node /regulator-vcck failed
[ 7.117184] VCCK: supplied by regulator-dummy
[ 7.117194] regulator-dummy: could not add device link regulator.8: -ENOENT
[ 7.117266] VCCK: 860 <--> 1140 mV at 986 mV, enabled
[ 7.118498] VDDEE: will resolve supply early: pwm
[ 7.118515] pwm-regulator regulator-vddee: Looking up pwm-supply from device tree
[ 7.118526] pwm-regulator regulator-vddee: Looking up pwm-supply property in node /regulator-vddee failed
[ 7.118553] VDDEE: supplied by regulator-dummy
[ 7.118563] regulator-dummy: could not add device link regulator.9: -ENOENT
Fixes: 524d96083b ("ARM: dts: meson8b: odroidc1: add the CPU voltage regulator")
Fixes: 8bdf38be71 ("ARM: dts: meson8b: odroidc1: add the VDDEE regulator")
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[narmstrong: fixed typo in commit s/observer/observe/]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210705112358.3554-2-linux.amoon@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44cf630bcb ]
We are seeing "imprecise external abort (0x1406)" errors during boot
(which then cause the whole board to hang) on Meson8 (but not Meson8m2).
These are observed while trying to access the GPU's registers when the
MALI clock is running at it's default setting of 24MHz. The 3.10 vendor
kernel uses 318.75MHz as "default" GPU frequency. Using that makes the
"imprecise external aborts" go away.
Add the assigned-clocks and assigned-clock-rates properties to also bump
the MALI clock to 318.75MHz before accessing any of it's registers.
Fixes: 7d3f6b536e ("ARM: dts: meson8: add the Mali-450 MP6 GPU")
Reported-by: Demetris Ierokipides <ierokipides.dem@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210711214023.2163565-1-martin.blumenstingl@googlemail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 525e2f9fd0 ]
st->bucket stores the current bucket number.
st->offset stores the offset within this bucket that is the sk to be
seq_show(). Thus, st->offset only makes sense within the same
st->bucket.
These two variables are an optimization for the common no-lseek case.
When resuming the seq_file iteration (i.e. seq_start()),
tcp_seek_last_pos() tries to continue from the st->offset
at bucket st->bucket.
However, it is possible that the bucket pointed by st->bucket
has changed and st->offset may end up skipping the whole st->bucket
without finding a sk. In this case, tcp_seek_last_pos() currently
continues to satisfy the offset condition in the next (and incorrect)
bucket. Instead, regardless of the offset value, the first sk of the
next bucket should be returned. Thus, "bucket == st->bucket" check is
added to tcp_seek_last_pos().
The chance of hitting this is small and the issue is a decade old,
so targeting for the next tree.
Fixes: a8b690f98b ("tcp: Fix slowness in read /proc/net/tcp")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20210701200541.1033917-1-kafai@fb.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9af417610b ]
The bounds check of id is off-by-one and the comparison should
be >= rather >. Currently the WARN_ON_ONCE check does not stop
the out of range indexing of &ldev->ctx.table[id] so also add
a return path if the bounds are out of range.
Addresses-Coverity: ("Illegal address computation").
Fixes: 5609c185f2 ("6lowpan: iphc: add support for stateful compression")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59da0b38bc ]
Smatch complains that some of these struct members are not initialized
leading to a stack information disclosure:
net/bluetooth/sco.c:778 sco_conn_defer_accept() warn:
check that 'cp.retrans_effort' doesn't leak information
This seems like a valid warning. I've added a default case to fix
this issue.
Fixes: 2f69a82acf ("Bluetooth: Use voice setting in deferred SCO connection request")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c275e5d349 ]
Inside function mt9m114_detect(), variable "retvalue" could
be uninitialized if mt9m114_read_reg() returns error, however, it
is used in the later if statement, which is potentially unsafe.
The local variable "retvalue" is renamed to "model" to avoid
confusion.
Link: https://lore.kernel.org/linux-media/20210625053858.3862-1-yzhai003@ucr.edu
Fixes: ad85094 (media / atomisp: fix the uninitialized use of model ID)
Signed-off-by: Yizhuo <yzhai003@ucr.edu>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44693d74f5 ]
The frame memory control register value is currently determined
before userspace selects the final capture format and never corrected.
Update ctx->frame_mem_ctrl in __coda_start_decoding() to fix decoding
into YUV420 or YVU420 capture buffers.
Reported-by: Andrej Picej <andrej.picej@norik.com>
Fixes: 497e6b8559 ("media: coda: add sequence initialization work")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e58430e1d4 ]
There are a few bugs in this code. 1) No checks for whether
dma_alloc_attrs() or __get_free_pages() failed. 2) If
video_register_device() fails it doesn't clean up the dma attrs or the
free pages. 3) The video_device_release() function frees "vfd" which
leads to a use after free on the next line. The call to
video_unregister_device() is not required so I have just removed that.
Fixes: f7e7b48e6d ("[media] rockchip/rga: v4l2 m2m support")
Reported-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0314339a0a ]
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f5885a775 ]
In go7007_alloc() kzalloc() is used for struct go7007
allocation. It means that there is no need in zeroing
any members, because kzalloc will take care of it.
Removing these reduntant initialization steps increases
execution speed a lot:
Before:
+ 86.802 us | go7007_alloc();
After:
+ 29.595 us | go7007_alloc();
Fixes: 866b8695d6 ("Staging: add the go7007 video driver")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 131ae388b8 ]
In dvb_usb_i2c_init, if i2c_add_adapter fails, it only prints an error
message, and then continues to set DVB_USB_STATE_I2C. This affects the
logic of dvb_usb_i2c_exit, which leads to that, the deletion of i2c_adap
even if the i2c_add_adapter fails.
Fix this by returning at the failure of i2c_add_adapter and then move
dvb_usb_i2c_exit out of the error handling code of dvb_usb_i2c_init.
Fixes: 13a79f14ab ("media: dvb-usb: Fix memory leak at error in dvb_usb_device_init()")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 797c061ad7 ]
If vp702x_usb_in_op fails, the mac address is not initialized.
And vp702x_read_mac_addr does not handle this failure, which leads to
the uninit-value in dvb_usb_adapter_dvb_init.
Fix this by handling the failure of vp702x_usb_in_op.
Fixes: 786baecfe7 ("[media] dvb-usb: move it to drivers/media/usb/dvb-usb")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5453769f7 ]
If dibusb_read_eeprom_byte fails, the mac address is not initialized.
And nova_t_read_mac_address does not handle this failure, which leads to
the uninit-value in dvb_usb_adapter_dvb_init.
Fix this by handling the failure of dibusb_read_eeprom_byte.
Reported-by: syzbot+e27b4fd589762b0b9329@syzkaller.appspotmail.com
Fixes: 786baecfe7 ("[media] dvb-usb: move it to drivers/media/usb/dvb-usb")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2255ff477 ]
The failure to register devlink will leave the system with dangled
devlink resource, which is not cleaned if devlink_port_register() fails.
In order to remove access to ".registered" field of struct devlink_port,
require both devlink_register and devlink_port_register to success and
check it through device pointer.
Fixes: fbfb803153 ("ionic: Add hardware init and device commands")
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ecc8cb7c0 ]
This race was discovered when I carefully analyzed the code to locate
another firmware-related UAF issue. It can be triggered only when the
firmware load operation is executed during suspend. This possibility is
almost impossible because there are few firmware load and suspend actions
in the actual environment.
CPU0 CPU1
__device_uncache_fw_images(): assign_fw():
fw_cache_piggyback_on_request()
<----- P0
spin_lock(&fwc->name_lock);
...
list_del(&fce->list);
spin_unlock(&fwc->name_lock);
uncache_firmware(fce->name);
<----- P1
kref_get(&fw_priv->ref);
If CPU1 is interrupted at position P0, the new 'fce' has been added to the
list fwc->fw_names by the fw_cache_piggyback_on_request(). In this case,
CPU0 executes __device_uncache_fw_images() and will be able to see it when
it traverses list fwc->fw_names. Before CPU1 executes kref_get() at P1, if
CPU0 further executes uncache_firmware(), the count of fw_priv->ref may
decrease to 0, causing fw_priv to be released in advance.
Move kref_get() to the lock protection range of fwc->name_lock to fix it.
Fixes: ac39b3ea73 ("firmware loader: let caching firmware piggyback on loading firmware")
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20210719064531.3733-2-thunder.leizhen@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6579cbfd7 ]
In the case where IS_ERR(lsi->si_sc_inode) is true the error exit path
to free_local does not kfree the allocated object lsi leading to a memory
leak. Fix this by kfree'ing lst before taking the error exit path.
Addresses-Coverity: ("Resource leak")
Fixes: 97fd734ba1 ("gfs2: lookup local statfs inodes prior to journal recovery")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d43b3a989b ]
rpmhpd_aggregate_corner() takes a corner as parameter, but in
rpmhpd_power_off() the code requests the level of the first corner
instead.
In all (known) current cases the first corner has level 0, so this
change should be a nop, but in case that there's a power domain with a
non-zero lowest level this makes sure that rpmhpd_power_off() actually
requests the lowest level - which is the closest to "power off" we can
get.
While touching the code, also skip the unnecessary zero-initialization
of "ret".
Fixes: 279b7e8a62 ("soc: qcom: rpmhpd: Add RPMh power domain driver")
Reviewed-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20210703005416.2668319-2-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b4b06919f ]
i40e_config_vf_promiscuous_mode() calls
i40e_getnum_vf_vsi_vlan_filters() without acquiring the
mac_filter_hash_lock spinlock.
This is unsafe because mac_filter_hash may get altered in another thread
while i40e_getnum_vf_vsi_vlan_filters() traverses the hashes.
Simply adding the spinlock in i40e_getnum_vf_vsi_vlan_filters() is not
possible as it already gets called in i40e_get_vlan_list_sync() with the
spinlock held. Therefore adding a wrapper that acquires the spinlock and
call the correct function where appropriate.
Fixes: 37d318d780 ("i40e: Remove scheduling while atomic possibility")
Fix-suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63a9192b8f ]
The 'tail' pointer is also free-running count, so it needs to be masked
as 'adminq_prod_cnt' does, to become an index value of AdminQ buffer.
Fixes: 5cdad90de6 ("gve: Batch AQ commands for creating and destroying queues.")
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Reviewed-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75f0fc7b48 ]
In bpf_patch_insn_data(), we first use the bpf_patch_insn_single() to
insert new instructions, then use adjust_insn_aux_data() to adjust
insn_aux_data. If the old env->prog have no enough room for new inserted
instructions, we use bpf_prog_realloc to construct new_prog and free the
old env->prog.
There have two errors here. First, if adjust_insn_aux_data() return
ENOMEM, we should free the new_prog. Second, if adjust_insn_aux_data()
return ENOMEM, bpf_patch_insn_data() will return NULL, and env->prog has
been freed in bpf_prog_realloc, but we will use it in bpf_check().
So in this patch, we make the adjust_insn_aux_data() never fails. In
bpf_patch_insn_data(), we first pre-malloc memory for the new
insn_aux_data, then call bpf_patch_insn_single() to insert new
instructions, at last call adjust_insn_aux_data() to adjust
insn_aux_data.
Fixes: 8041902dae ("bpf: adjust insn_aux_data when patching insns")
Signed-off-by: He Fengqing <hefengqing@huawei.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20210714101815.164322-1-hefengqing@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dcb0145821 ]
If an error occurs after a successful 'regulator_enable()' call,
'regulator_disable()' must be called.
Fix the error handling path of the probe accordingly.
Fixes: cb496cd472 ("media: cxd2880-spi: Add optional vcc regulator")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e642197562 ]
The error code is missing in this code scenario, add the error code
'-EINVAL' to the return value 'ret'.
Eliminate the follow smatch warning:
drivers/leds/leds-is31fl32xx.c:388 is31fl32xx_parse_dt() warn: missing
error code 'ret'.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Fixes: 9d7cffaf99 ("leds: Add driver for the ISSI IS31FL32xx family of LED controllers")
Acked-by: David Rivshin <drivshin@allworx.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea3e1c36e3 ]
Without this patch, the TDA19971 chip's EDID is inactive.
EDID never worked with this driver, it was all tested with HDMI signal
sources which don't need EDID support.
Signed-off-by: Krzysztof Halasa <khalasa@piap.pl>
Fixes: 9ac0038db9 ("media: i2c: Add TDA1997x HDMI receiver driver")
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2294a7299f ]
MCDDRCFG is a per-channel register and uses bit{0,1} to indicate
the NVDIMM presence on DIMM slot{0,1}. Current i10nm_edac driver
wrongly uses MCDDRCFG as per-DIMM register and fails to detect
the NVDIMM.
Fix it by reading MCDDRCFG as per-channel register and using its
bit{0,1} to check whether the NVDIMM is populated on DIMM slot{0,1}.
Fixes: d4dc89d069 ("EDAC, i10nm: Add a driver for Intel 10nm server processors")
Reported-by: Fan Du <fan.du@intel.com>
Tested-by: Wen Jin <wen.jin@intel.com>
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/r/20210818175701.1611513-2-tony.luck@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26cfc0dbe4 ]
The function wait_for_completion_interruptible_timeout will return
-ERESTARTSYS immediately when receiving SIGKILL signal which is sent
by "jffs2_gcd_mtd" during umounting jffs2. This will break the SPI memory
operation because the data transmitting may begin before the command or
address transmitting completes. Use wait_for_completion_timeout to prevent
the process from being interruptible.
Fixes: 67dca5e580 ("spi: spi-mem: Add support for Zynq QSPI controller")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20210826005930.20572-1-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 98e47570ba ]
In commit e915331149 ("regulator: vctrl-regulator: Avoid deadlock getting
and setting the voltage"), all calls to get/set the voltage of the
control regulator were switched to unlocked versions to avoid deadlocks.
However, the call in the probe path is done without regulator locks
held. In this case the locked version should be used.
Switch back to the locked regulator_get_voltage() in the probe path to
avoid any mishaps.
Fixes: e915331149 ("regulator: vctrl-regulator: Avoid deadlock getting and setting the voltage")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20210825033704.3307263-2-wenst@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc40b72251 ]
dun_bytes needs to be less than or equal to the IV size of the
encryption mode, not just less than or equal to BLK_CRYPTO_MAX_IV_SIZE.
Currently this doesn't matter since blk_crypto_init_key() is never
actually passed invalid values, but we might as well fix this.
Fixes: a892c8d52c ("block: Inline encryption support for blk-mq")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20210825055918.51975-1-ebiggers@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3bff147b18 ]
When a fatal machine check results in a system reset, Linux does not
clear the error(s) from machine check bank(s) - hardware preserves the
machine check banks across a warm reset.
During initialization of the kernel after the reboot, Linux reads, logs,
and clears all machine check banks.
But there is a problem. In:
5de97c9f6d ("x86/mce: Factor out and deprecate the /dev/mcelog driver")
the call to mce_register_decode_chain() moved later in the boot
sequence. This means that /dev/mcelog doesn't see those early error
logs.
This was partially fixed by:
cd9c57cad3 ("x86/MCE: Dump MCE to dmesg if no consumers")
which made sure that the logs were not lost completely by printing
to the console. But parsing console logs is error prone. Users of
/dev/mcelog should expect to find any early errors logged to standard
places.
Add a new flag MCP_QUEUE_LOG to machine_check_poll() to be used in early
machine check initialization to indicate that any errors found should
just be queued to genpool. When mcheck_late_init() is called it will
call mce_schedule_work() to actually log and flush any errors queued in
the genpool.
[ Based on an original patch, commit message by and completely
productized by Tony Luck. ]
Fixes: 5de97c9f6d ("x86/mce: Factor out and deprecate the /dev/mcelog driver")
Reported-by: Sumanth Kamatala <skamatala@juniper.net>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20210824003129.GA1642753@agluck-desk2.amr.corp.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 047d4226b0 ]
When rngd is run as root then lots of these types of message will appear
in the kernel log if the TPM has been configured to provide random bytes:
[ 7406.275163] tpm tpm0: tpm_transmit: tpm_recv: error -4
The issue is caused by the following call that is interrupted while
waiting for the TPM's response.
sig = wait_event_interruptible(ibmvtpm->wq, !ibmvtpm->tpm_processing_cmd);
Rather than waiting for the response in the low level driver, have it use
the polling loop in tpm_try_transmit() that uses a command's duration to
poll until a result has been returned by the TPM, thus ending when the
timeout has occurred but not responding to signals and ctrl-c anymore. To
stay in this polling loop extend tpm_ibmvtpm_status() to return
'true' for as long as the vTPM is indicated as being busy in
tpm_processing_cmd. Since the loop requires the TPM's timeouts, get them
now using tpm_get_timeouts() after setting the TPM2 version flag on the
chip.
To recreat the resolved issue start rngd like this:
sudo rngd -r /dev/hwrng -t
sudo rngd -r /dev/tpm0 -t
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1981473
Fixes: 6674ff145e ("tpm_ibmvtpm: properly handle interrupted packet receptions")
Cc: Nayna Jain <nayna@linux.ibm.com>
Cc: George Wilson <gcwilson@linux.ibm.com>
Reported-by: Nageswara R Sastry <rnsastry@linux.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: Nageswara R Sastry <rnsastry@linux.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea35e0d5df ]
Address a kbuild issue where a developer created an ECDSA key for signing
kernel modules and then builds an older version of the kernel, when bi-
secting the kernel for example, that does not support ECDSA keys.
If openssl is installed, trigger the creation of an RSA module signing
key if it is not an RSA key.
Fixes: cfc411e7ff ("Move certificate handling to its own directory")
Cc: David Howells <dhowells@redhat.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 462354d986 ]
Replace vf_mask type with unsigned long to avoid a stack-out-of-bound.
This is to fix the following warning reported by KASAN the first time
adf_msix_isr_ae() gets called.
[ 692.091987] BUG: KASAN: stack-out-of-bounds in find_first_bit+0x28/0x50
[ 692.092017] Read of size 8 at addr ffff88afdf789e60 by task swapper/32/0
[ 692.092076] Call Trace:
[ 692.092089] <IRQ>
[ 692.092101] dump_stack+0x9c/0xcf
[ 692.092132] print_address_description.constprop.0+0x18/0x130
[ 692.092164] ? find_first_bit+0x28/0x50
[ 692.092185] kasan_report.cold+0x7f/0x111
[ 692.092213] ? static_obj+0x10/0x80
[ 692.092234] ? find_first_bit+0x28/0x50
[ 692.092262] find_first_bit+0x28/0x50
[ 692.092288] adf_msix_isr_ae+0x16e/0x230 [intel_qat]
Fixes: ed8ccaef52 ("crypto: qat - Add support for SRIOV")
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1a811633f ]
Syzbot hit WARNING in internal_create_group(). The problem was in
too big disk->first_minor.
disk->first_minor is initialized by value, which comes from userspace
and there wasn't any sanity checks about value correctness. It can cause
duplicate creation of sysfs files/links, because disk->first_minor will
be passed to MKDEV() which causes truncation to byte. Since maximum
minor value is 0xff, let's check if first_minor is correct minor number.
NOTE: the root case of the reported warning was in wrong error handling
in register_disk(), but we can avoid passing knowingly wrong values to
sysfs API, because sysfs error messages can confuse users. For example:
user passed 1048576 as index, but sysfs complains about duplicate
creation of /dev/block/43:0. It's not obvious how 1048576 becomes 0.
Log and reproducer for above example can be found on syzkaller bug
report page.
Link: https://syzkaller.appspot.com/bug?id=03c2ae9146416edf811958d5fd7acfab75b143d1
Fixes: b0d9111a2d ("nbd: use an idr to keep track of nbd devices")
Reported-by: syzbot+9937dc42271cd87d4b98@syzkaller.appspotmail.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be83c3b6e7 ]
If CMT instance has at least two channels, one channel will be used
as a clock source and another one used as a clock event device.
In that case, IRQ is not requested for clock source channel so
sh_cmt_clock_event_program_verify() might work incorrectly.
Besides, when a channel is only used for clock source, don't need to
re-set the next match_value since it should be maximum timeout as
it still is.
On the other hand, due to no IRQ, total_cycles is not counted up
when reaches compare match time (timer counter resets to zero),
so sh_cmt_clocksource_read() returns unexpected value.
Therefore, use 64-bit clocksoure's mask for 32-bit or 16-bit variants
will also lead to wrong delta calculation. Hence, this mask should
correspond to timer counter width, and above function just returns
the raw value of timer counter register.
Fixes: bfa76bb12f ("clocksource: sh_cmt: Request IRQ for clock event device only")
Fixes: 37e7742c55 ("clocksource/drivers/sh_cmt: Fix clocksource width for 32-bit machines")
Signed-off-by: Phong Hoang <phong.hoang.wz@renesas.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210422123443.73334-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6f756726e ]
We should set the additional space to 0 in mpi_resize().
So use kcalloc() instead of kmalloc_array().
In lib/mpi/ec.c:
/****************
* Resize the array of A to NLIMBS. the additional space is cleared
* (set to 0) [done by m_realloc()]
*/
int mpi_resize(MPI a, unsigned nlimbs)
Like the comment of kernel's mpi_resize() said, the additional space
need to be set to 0, but when a->d is not NULL, it does not set.
The kernel's mpi lib is from libgcrypt, the mpi resize in libgcrypt
is _gcry_mpi_resize() which set the additional space to 0.
This bug may cause mpi api which use mpi_resize() get wrong result
under the condition of using the additional space without initiation.
If this condition is not met, the bug would not be triggered.
Currently in kernel, rsa, sm2 and dh use mpi lib, and they works well,
so the bug is not triggered in these cases.
add_points_edwards() use the additional space directly, so it will
get a wrong result.
Fixes: cdec9cb516 ("crypto: GnuPG based MPI lib - source files (part 1)")
Signed-off-by: Hongbo Li <herberthbli@tencent.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 976c1de1de ]
Depending on the DMA driver being used, the struct dma_slave_config may
need to be initialized to zero for the unused data.
For example, we have three DMA drivers using src_port_window_size and
dst_port_window_size. If these are left uninitialized, it can cause DMA
failures.
For spi-pic32, this is probably not currently an issue but is still good to
fix though.
Fixes: 1bcb9f8ceb ("spi: spi-pic32: Add PIC32 SPI master driver")
Cc: Purna Chandra Mandal <purna.mandal@microchip.com>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210810081727.19491-2-tony@atomide.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 866663b7b5 ]
When merging one bio to request, if they are discard IO and the queue
supports multi-range discard, we need to return ELEVATOR_DISCARD_MERGE
because both block core and related drivers(nvme, virtio-blk) doesn't
handle mixed discard io merge(traditional IO merge together with
discard merge) well.
Fix the issue by returning ELEVATOR_DISCARD_MERGE in this situation,
so both blk-mq and drivers just need to handle multi-range discard.
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Fixes: 2705dfb209 ("block: fix discard request merge")
Link: https://lore.kernel.org/r/20210729034226.1591070-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2189e928b6 ]
When enabling CONFIG_RMW_INSNS in e.g. a Coldfire build:
{standard input}:3068: Error: invalid instruction for this architecture; needs 68020 or higher (68020 [68k, 68ec020], 68030 [68ec030], 68040 [68ec040], 68060 [68ec060]) -- statement `casl %d4,%d0,(%a6)' ignored
Fix this by (a) adding a new config symbol to track if support for any
CPU that lacks the CAS instruction is enabled, and (b) making
CONFIG_RMW_INSNS depend on the new symbol not being set.
Fixes: 0e152d8050 ("m68k: reorganize Kconfig options to improve mmu/non-mmu selections")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210725104413.318932-1-geert@linux-m68k.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc87740c8a ]
If rcu_print_task_stall() is invoked on an rcu_node structure that does
not contain any tasks blocking the current grace period, it takes an
early exit that fails to release that rcu_node structure's lock. This
results in a self-deadlock, which is detected by lockdep.
To reproduce this bug:
tools/testing/selftests/rcutorture/bin/kvm.sh --allcpus --duration 3 --trust-make --configs "TREE03" --kconfig "CONFIG_PROVE_LOCKING=y" --bootargs "rcutorture.stall_cpu=30 rcutorture.stall_cpu_block=1 rcutorture.fwd_progress=0 rcutorture.test_boost=0"
This will also result in other complaints, including RCU's scheduler
hook complaining about blocking rather than preemption and an rcutorture
writer stall.
Only a partial RCU CPU stall warning message will be printed because of
the self-deadlock.
This commit therefore releases the lock on the rcu_print_task_stall()
function's early exit path.
Fixes: c583bcb8f5 ("rcu: Don't invoke try_invoke_on_locked_down_task() with irqs disabled")
Tested-by: Qais Yousef <qais.yousef@arm.com>
Signed-off-by: Yanfei Xu <yanfei.xu@windriver.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a649d25dcc ]
This commit adds a number of lockdep_assert_irqs_disabled() calls
to rcu_sched_clock_irq() and a number of the functions that it calls.
The point of this is to help track down a situation where lockdep appears
to be insisting that interrupts are enabled within these functions, which
should only ever be invoked from the scheduling-clock interrupt handler.
Link: https://lore.kernel.org/lkml/20201111133813.GA81547@elver.google.com/
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6a901a44f ]
The for loop in rcu_print_task_stall() always omits ts[0], which points
to the first task blocking the stalled grace period. This in turn fails
to count this first task, which means that ndetected will be equal to
zero when all CPUs have passed through their quiescent states and only
one task is blocking the stalled grace period. This zero value for
ndetected will in turn result in an incorrect "All QSes seen" message:
rcu: INFO: rcu_preempt detected stalls on CPUs/tasks:
rcu: Tasks blocked on level-1 rcu_node (CPUs 12-23):
(detected by 15, t=6504 jiffies, g=164777, q=9011209)
rcu: All QSes seen, last rcu_preempt kthread activity 1 (4295252379-4295252378), jiffies_till_next_fqs=1, root ->qsmask 0x2
BUG: sleeping function called from invalid context at include/linux/uaccess.h:156
in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 70613, name: msgstress04
INFO: lockdep is turned off.
Preemption disabled at:
[<ffff8000104031a4>] create_object.isra.0+0x204/0x4b0
CPU: 15 PID: 70613 Comm: msgstress04 Kdump: loaded Not tainted
5.12.2-yoctodev-standard #1
Hardware name: Marvell OcteonTX CN96XX board (DT)
Call trace:
dump_backtrace+0x0/0x2cc
show_stack+0x24/0x30
dump_stack+0x110/0x188
___might_sleep+0x214/0x2d0
__might_sleep+0x7c/0xe0
This commit therefore fixes the loop to include ts[0].
Fixes: c583bcb8f5 ("rcu: Don't invoke try_invoke_on_locked_down_task() with irqs disabled")
Tested-by: Qais Yousef <qais.yousef@arm.com>
Signed-off-by: Yanfei Xu <yanfei.xu@windriver.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca4984a7dd ]
The UCLAMP_FLAG_IDLE flag is set on a runqueue when dequeueing the last
uclamp active task (that is, when buckets.tasks reaches 0 for all
buckets) to maintain the last uclamp.max and prevent blocked util from
suddenly becoming visible.
However, there is an asymmetry in how the flag is set and cleared which
can lead to having the flag set whilst there are active tasks on the rq.
Specifically, the flag is cleared in the uclamp_rq_inc() path, which is
called at enqueue time, but set in uclamp_rq_dec_id() which is called
both when dequeueing a task _and_ in the update_uclamp_active() path. As
a result, when both uclamp_rq_{dec,ind}_id() are called from
update_uclamp_active(), the flag ends up being set but not cleared,
hence leaving the runqueue in a broken state.
Fix this by clearing the flag in update_uclamp_active() as well.
Fixes: e496187da7 ("sched/uclamp: Enforce last task's UCLAMP_MAX")
Reported-by: Rick Yiu <rickyiu@google.com>
Signed-off-by: Quentin Perret <qperret@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Qais Yousef <qais.yousef@arm.com>
Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Link: https://lore.kernel.org/r/20210805102154.590709-2-qperret@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad1abe4769 ]
Deal with deferred probe using dev_err_probe so the error is handled
and avoid logging lots probe defer information like the following:
[ 9.125121] cw2015 4-0062: Failed to register power supply
[ 9.211131] cw2015 4-0062: Failed to register power supply
Fixes: b4c7715c10 ("power: supply: add CellWise cw2015 fuel gauge driver")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cabebb697c ]
If for any reason the interrupt enable for an ap queue fails the
state machine run for the queue returned wrong return codes to the
caller. So the caller assumed interrupt support for this queue in
enabled and thus did not re-establish the high resolution timer used
for polling. In the end this let to a hang for the user space process
waiting "forever" for the reply.
This patch reworks these return codes to return correct indications
for the caller to re-establish the timer when a queue runs without
interrupt support.
Please note that this is fixing a wrong behavior after a first
failure (enable interrupt support for the queue) failed. However,
looks like this occasionally happens on KVM systems.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9372a82892 ]
Currently allocation and registration of s390dbf debug areas are tied
together. As a result, a debug area cannot be unregistered and
re-registered while any process has an associated debugfs file open.
Fix this by splitting alloc/release from register/unregister.
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1204777867 ]
Any previously recorded s390dbf debug data is reset when a debug area
is resized using the 'pages' sysfs attribute. This can make
live-debugging unnecessarily complex.
Fix this by copying existing debug data to the newly allocated debug
area when resizing.
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7addcdd52 ]
Currently clp_set_pci_fn() always returns 0 as long as the CLP request
itself succeeds even if the operation itself returns a response code
other than CLP_RC_OK or CLP_RC_SETPCIFN_ALRDY. This is highly misleading
because calling code assumes that a zero rc means that the operation was
successful.
Fix this by returning the response code or cc on failure with the
exception of the special handling for CLP_RC_SETPCIFN_ALRDY. Also let's
not assume that the returned function handle for CLP_RC_SETPCIFN_ALRDY
is 0, we don't need it anyway.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f488f698f ]
There is an existing lock hierarchy of
&dev->event_lock --> &fasync_struct.fa_lock --> &f->f_owner.lock
from the following call chain:
input_inject_event():
spin_lock_irqsave(&dev->event_lock,...);
input_handle_event():
input_pass_values():
input_to_handler():
evdev_events():
evdev_pass_values():
spin_lock(&client->buffer_lock);
__pass_event():
kill_fasync():
kill_fasync_rcu():
read_lock(&fa->fa_lock);
send_sigio():
read_lock_irqsave(&fown->lock,...);
&dev->event_lock is HARDIRQ-safe, so interrupts have to be disabled
while grabbing &fasync_struct.fa_lock, otherwise we invert the lock
hierarchy. However, since kill_fasync which calls kill_fasync_rcu is
an exported symbol, it may not necessarily be called with interrupts
disabled.
As kill_fasync_rcu may be called with interrupts disabled (for
example, in the call chain above), we replace calls to
read_lock/read_unlock on &fasync_struct.fa_lock in kill_fasync_rcu
with read_lock_irqsave/read_unlock_irqrestore.
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 645ae0af18 ]
The function adf_iov_putmsg() is only used inside the intel_qat module
therefore should not be exported.
Remove EXPORT_SYMBOL for the function adf_iov_putmsg().
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b90c1c4d3f ]
At start and shutdown, VFs notify the PF about their state. These
notifications are carried out through a message exchange using the PFVF
protocol.
Function names lead to believe they do perform init or shutdown logic.
This is to fix the naming to better reflect their purpose.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a73c762e1 ]
The top half of the VF drivers handled only a source at the time.
If an interrupt for PF2VF and bundle occurred at the same time, the ISR
scheduled only the bottom half for PF2VF.
This patch fixes the VF top half so that if both sources of interrupt
trigger at the same time, both bottom halves are scheduled.
This patch is based on earlier work done by Conor McLoughlin.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5147f0906d ]
The function adf_dev_init() ignores the error code reported by
enable_vf2pf_comms(). If the latter fails, e.g. the VF is not compatible
with the pf, then the load of the VF driver progresses.
This patch changes adf_dev_init() so that the error code from
enable_vf2pf_comms() is returned to the caller.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe4d55773b ]
lockdep complains that in omap-aes, the list_lock is taken both with
softirqs enabled at probe time, and also in softirq context, which
could lead to a deadlock:
================================
WARNING: inconsistent lock state
5.14.0-rc1-00035-gc836005b01c5-dirty #69 Not tainted
--------------------------------
inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
ksoftirqd/0/7 [HC0[0]:SC1[3]:HE1:SE0] takes:
bf00e014 (list_lock){+.?.}-{2:2}, at: omap_aes_find_dev+0x18/0x54 [omap_aes_driver]
{SOFTIRQ-ON-W} state was registered at:
_raw_spin_lock+0x40/0x50
omap_aes_probe+0x1d4/0x664 [omap_aes_driver]
platform_probe+0x58/0xb8
really_probe+0xbc/0x314
__driver_probe_device+0x80/0xe4
driver_probe_device+0x30/0xc8
__driver_attach+0x70/0xf4
bus_for_each_dev+0x70/0xb4
bus_add_driver+0xf0/0x1d4
driver_register+0x74/0x108
do_one_initcall+0x84/0x2e4
do_init_module+0x5c/0x240
load_module+0x221c/0x2584
sys_finit_module+0xb0/0xec
ret_fast_syscall+0x0/0x2c
0xbed90b30
irq event stamp: 111800
hardirqs last enabled at (111800): [<c02a21e4>] __kmalloc+0x484/0x5ec
hardirqs last disabled at (111799): [<c02a21f0>] __kmalloc+0x490/0x5ec
softirqs last enabled at (111776): [<c01015f0>] __do_softirq+0x2b8/0x4d0
softirqs last disabled at (111781): [<c0135948>] run_ksoftirqd+0x34/0x50
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(list_lock);
<Interrupt>
lock(list_lock);
*** DEADLOCK ***
2 locks held by ksoftirqd/0/7:
#0: c0f5e8c8 (rcu_read_lock){....}-{1:2}, at: netif_receive_skb+0x6c/0x260
#1: c0f5e8c8 (rcu_read_lock){....}-{1:2}, at: ip_local_deliver_finish+0x2c/0xdc
stack backtrace:
CPU: 0 PID: 7 Comm: ksoftirqd/0 Not tainted 5.14.0-rc1-00035-gc836005b01c5-dirty #69
Hardware name: Generic AM43 (Flattened Device Tree)
[<c010e6e0>] (unwind_backtrace) from [<c010b9d0>] (show_stack+0x10/0x14)
[<c010b9d0>] (show_stack) from [<c017c640>] (mark_lock.part.17+0x5bc/0xd04)
[<c017c640>] (mark_lock.part.17) from [<c017d9e4>] (__lock_acquire+0x960/0x2fa4)
[<c017d9e4>] (__lock_acquire) from [<c0180980>] (lock_acquire+0x10c/0x358)
[<c0180980>] (lock_acquire) from [<c093d324>] (_raw_spin_lock_bh+0x44/0x58)
[<c093d324>] (_raw_spin_lock_bh) from [<bf00b258>] (omap_aes_find_dev+0x18/0x54 [omap_aes_driver])
[<bf00b258>] (omap_aes_find_dev [omap_aes_driver]) from [<bf00b328>] (omap_aes_crypt+0x94/0xd4 [omap_aes_driver])
[<bf00b328>] (omap_aes_crypt [omap_aes_driver]) from [<c08ac6d0>] (esp_input+0x1b0/0x2c8)
[<c08ac6d0>] (esp_input) from [<c08c9e90>] (xfrm_input+0x410/0x1290)
[<c08c9e90>] (xfrm_input) from [<c08b6374>] (xfrm4_esp_rcv+0x54/0x11c)
[<c08b6374>] (xfrm4_esp_rcv) from [<c0838840>] (ip_protocol_deliver_rcu+0x48/0x3bc)
[<c0838840>] (ip_protocol_deliver_rcu) from [<c0838c50>] (ip_local_deliver_finish+0x9c/0xdc)
[<c0838c50>] (ip_local_deliver_finish) from [<c0838dd8>] (ip_local_deliver+0x148/0x1b0)
[<c0838dd8>] (ip_local_deliver) from [<c0838f5c>] (ip_rcv+0x11c/0x180)
[<c0838f5c>] (ip_rcv) from [<c077e3a4>] (__netif_receive_skb_one_core+0x54/0x74)
[<c077e3a4>] (__netif_receive_skb_one_core) from [<c077e588>] (netif_receive_skb+0xa8/0x260)
[<c077e588>] (netif_receive_skb) from [<c068d6d4>] (cpsw_rx_handler+0x224/0x2fc)
[<c068d6d4>] (cpsw_rx_handler) from [<c0688ccc>] (__cpdma_chan_process+0xf4/0x188)
[<c0688ccc>] (__cpdma_chan_process) from [<c068a0c0>] (cpdma_chan_process+0x3c/0x5c)
[<c068a0c0>] (cpdma_chan_process) from [<c0690e14>] (cpsw_rx_mq_poll+0x44/0x98)
[<c0690e14>] (cpsw_rx_mq_poll) from [<c0780810>] (__napi_poll+0x28/0x268)
[<c0780810>] (__napi_poll) from [<c0780c64>] (net_rx_action+0xcc/0x204)
[<c0780c64>] (net_rx_action) from [<c0101478>] (__do_softirq+0x140/0x4d0)
[<c0101478>] (__do_softirq) from [<c0135948>] (run_ksoftirqd+0x34/0x50)
[<c0135948>] (run_ksoftirqd) from [<c01583b8>] (smpboot_thread_fn+0xf4/0x1d8)
[<c01583b8>] (smpboot_thread_fn) from [<c01546dc>] (kthread+0x14c/0x174)
[<c01546dc>] (kthread) from [<c010013c>] (ret_from_fork+0x14/0x38)
...
The omap-des and omap-sham drivers appear to have a similar issue.
Fix this by using spin_{,un}lock_bh() around device list access in all
the probe and remove functions.
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8617bb7400 ]
Tests showed a mismatch between what the CCA tool reports about
the APKA master key state and what's displayed by the zcrypt dd
in sysfs. After some investigation, we found out that the
documentation which was the source for the zcrypt dd implementation
lacks the listing of 3 fields. So this patch now moves the
evaluation of the APKA master key state to the correct offset.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3683c0552 ]
Introduce dev_busid, which exports the device-id associated with the
io-subchannel (and message-subchannel). The dev_busid indicates that of
the device which may be physically installed on the corrosponding
subchannel. The dev_busid value "none" indicates that the subchannel
is not valid, there is no I/O device currently associated with the
subchannel.
The dev_busid information would be helpful to write device-specific
udev-rules associated with the subchannel. The dev_busid interface would
be available even when the sch is not bound to any driver or if there is
no operational device connected on it. Hence this attribute can be used to
write udev-rules which are specific to the device associated with the
subchannel.
Signed-off-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit efe2175478 ]
Pin control needs to be activated by setting the enable bit, otherwise
hardware rejects all pin changes. Previously this stayed unnoticed on
Nexus 7 because pin control was enabled by default after rebooting from
downstream kernel, which uses driver that enables the bit and charger
registers are non-volatile until power supply (battery) is disconnected.
Configure the pin control enable bit. This fixes the potentially
never-enabled charging on devices that use pin control.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e804d5abe2 ]
According to the NVMe specification, the response dword 0 value of the
Connect command is based on status code: return cntlid for successful
compeltion return IPO and IATTR for connect invalid parameters. Fix
a missing error information for a zero sized queue, and return the
cntlid also for I/O queue Connect commands.
Signed-off-by: Amit Engel <amit.engel@dell.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 85032874f8 ]
We update ctrl->queue_count and schedule another reconnect when io queue
count is zero.But we will never try to create any io queue in next reco-
nnection, because ctrl->queue_count already set to zero.We will end up
having an admin-only session in Live state, which is exactly what we try
to avoid in the original patch.
Update ctrl->queue_count after queue_count zero checking to fix it.
Signed-off-by: Ruozhu Li <liruozhu@huawei.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 664227fde6 ]
We update ctrl->queue_count and schedule another reconnect when io queue
count is zero.But we will never try to create any io queue in next reco-
nnection, because ctrl->queue_count already set to zero.We will end up
having an admin-only session in Live state, which is exactly what we try
to avoid in the original patch.
Update ctrl->queue_count after queue_count zero checking to fix it.
Signed-off-by: Ruozhu Li <liruozhu@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f1e9630af ]
After patch 54efd50 (block: make generic_make_request handle
arbitrarily sized bios), the IO through io-throttle may be larger,
and these IOs may be further split into more small IOs. However,
IOPS throttle does not seem to be aware of this change, which
makes the calculation of IOPS of large IOs incomplete, resulting
in disk-side IOPS that does not meet expectations. Maybe we should
fix this problem.
We can reproduce it by set max_sectors_kb of disk to 128, set
blkio.write_iops_throttle to 100, run a dd instance inside blkio
and use iostat to watch IOPS:
dd if=/dev/zero of=/dev/sdb bs=1M count=1000 oflag=direct
As a result, without this change the average IOPS is 1995, with
this change the IOPS is 98.
Signed-off-by: Chunguang Xu <brookxu@tencent.com>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/65869aaad05475797d63b4c3fed4f529febe3c26.1627876014.git.brookxu@tencent.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28ce50f8d9 ]
Currently iocharset=utf8 mount option is broken. To use UTF-8 as iocharset,
it is required to use utf8 mount option.
Fix iocharset=utf8 mount option to use be equivalent to the utf8 mount
option.
If UTF-8 as iocharset is used then s_nls_iocharset is set to NULL. So
simplify code around, remove s_utf8 field as to distinguish between UTF-8
and non-UTF-8 it is needed just to check if s_nls_iocharset is set to NULL
or not.
Link: https://lore.kernel.org/r/20210808162453.1653-5-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b645333443 ]
Currently iocharset=utf8 mount option is broken. To use UTF-8 as iocharset,
it is required to use utf8 mount option.
Fix iocharset=utf8 mount option to use be equivalent to the utf8 mount
option.
If UTF-8 as iocharset is used then s_nls_map is set to NULL. So simplify
code around, remove UDF_FLAG_NLS_MAP and UDF_FLAG_UTF8 flags as to
distinguish between UTF-8 and non-UTF-8 it is needed just to check if
s_nls_map set to NULL or not.
Link: https://lore.kernel.org/r/20210808162453.1653-4-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 781d2a9a2f ]
We were checking validity of LVID entries only when getting
implementation use information from LVID in udf_sb_lvidiu(). However if
the LVID is suitably corrupted, it can cause problems also to code such
as udf_count_free() which doesn't use udf_sb_lvidiu(). So check validity
of LVID already when loading it from the disk and just disable LVID
altogether when it is not valid.
Reported-by: syzbot+7fbfe5fed73ebb675748@syzkaller.appspotmail.com
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c3b5e6ec0 ]
If high resolution timers are disabled the timerfd notification about a
clock was set event is not happening for all cases which use
clock_was_set_delayed() because that's a NOP for HIGHRES=n, which is wrong.
Make clock_was_set_delayed() unconditially available to fix that.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210713135158.196661266@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 627ef5ae2d ]
If __hrtimer_start_range_ns() is invoked with an already armed hrtimer then
the timer has to be canceled first and then added back. If the timer is the
first expiring timer then on removal the clockevent device is reprogrammed
to the next expiring timer to avoid that the pending expiry fires needlessly.
If the new expiry time ends up to be the first expiry again then the clock
event device has to reprogrammed again.
Avoid this by checking whether the timer is the first to expire and in that
case, keep the timer on the current CPU and delay the reprogramming up to
the point where the timer has been enqueued again.
Reported-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210713135157.873137732@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 406dd42bd1 ]
When an itimer deactivates a previously armed expiration, it simply doesn't
do anything. As a result the process wide cputime counter keeps running and
the tick dependency stays set until it reaches the old ghost expiration
value.
This can be reproduced with the following snippet:
void trigger_process_counter(void)
{
struct itimerval n = {};
n.it_value.tv_sec = 100;
setitimer(ITIMER_VIRTUAL, &n, NULL);
n.it_value.tv_sec = 0;
setitimer(ITIMER_VIRTUAL, &n, NULL);
}
Fix this with resetting the relevant base expiration. This is similar to
disarming a timer.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20210726125513.271824-4-frederic@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 767f4b620e ]
Hypervisors likely do not expose the SMCA feature to the guest and
loading this module leads to false warnings. This module should not be
loaded in guests to begin with, but people tend to do so, especially
when testing kernels in VMs. And then they complain about those false
warnings.
Do the practical thing and do not load this module when running as a
guest to avoid all that complaining.
[ bp: Rewrite commit message. ]
Suggested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Smita Koralahalli <Smita.KoralahalliChannabasappa@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Yazen Ghannam <yazen.ghannam@amd.com>
Tested-by: Kim Phillips <kim.phillips@amd.com>
Link: https://lkml.kernel.org/r/20210628172740.245689-1-Smita.KoralahalliChannabasappa@amd.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ccfc9dd691 ]
The soft watchdog timer function checks if a virtual machine
was suspended and hence what looks like a lockup in fact
is a false positive.
This is what kvm_check_and_clear_guest_paused() does: it
tests guest PVCLOCK_GUEST_STOPPED (which is set by the host)
and if it's set then we need to touch all watchdogs and bail
out.
Watchdog timer function runs from IRQ, so PVCLOCK_GUEST_STOPPED
check works fine.
There is, however, one more watchdog that runs from IRQ, so
watchdog timer fn races with it, and that watchdog is not aware
of PVCLOCK_GUEST_STOPPED - RCU stall detector.
apic_timer_interrupt()
smp_apic_timer_interrupt()
hrtimer_interrupt()
__hrtimer_run_queues()
tick_sched_timer()
tick_sched_handle()
update_process_times()
rcu_sched_clock_irq()
This triggers RCU stalls on our devices during VM resume.
If tick_sched_handle()->rcu_sched_clock_irq() runs on a VCPU
before watchdog_timer_fn()->kvm_check_and_clear_guest_paused()
then there is nothing on this VCPU that touches watchdogs and
RCU reads stale gp stall timestamp and new jiffies value, which
makes it think that RCU has stalled.
Make RCU stall watchdog aware of PVCLOCK_GUEST_STOPPED and
don't report RCU stalls when we resume the VM.
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4da13aa28 ]
A missing clock update is causing the following warning:
rq->clock_update_flags < RQCF_ACT_SKIP
WARNING: CPU: 112 PID: 2041 at kernel/sched/sched.h:1453
sub_running_bw.isra.0+0x190/0x1a0
...
CPU: 112 PID: 2041 Comm: sugov:112 Tainted: G W 5.14.0-rc1 #1
Hardware name: WIWYNN Mt.Jade Server System
B81.030Z1.0007/Mt.Jade Motherboard, BIOS 1.6.20210526 (SCP:
1.06.20210526) 2021/05/26
...
Call trace:
sub_running_bw.isra.0+0x190/0x1a0
migrate_task_rq_dl+0xf8/0x1e0
set_task_cpu+0xa8/0x1f0
try_to_wake_up+0x150/0x3d4
wake_up_q+0x64/0xc0
__up_write+0xd0/0x1c0
up_write+0x4c/0x2b0
cppc_set_perf+0x120/0x2d0
cppc_cpufreq_set_target+0xe0/0x1a4 [cppc_cpufreq]
__cpufreq_driver_target+0x74/0x140
sugov_work+0x64/0x80
kthread_worker_fn+0xe0/0x230
kthread+0x138/0x140
ret_from_fork+0x10/0x18
The task causing this is the `cppc_fie` DL task introduced by
commit 1eb5dde674 ("cpufreq: CPPC: Add support for frequency
invariance").
With CONFIG_ACPI_CPPC_CPUFREQ_FIE=y and schedutil cpufreq governor on
slow-switching system (like on this Ampere Altra WIWYNN Mt. Jade Arm
Server):
DL task `curr=sugov:112` lets `p=cppc_fie` migrate and since the latter
is in `non_contending` state, migrate_task_rq_dl() calls
sub_running_bw()->__sub_running_bw()->cpufreq_update_util()->
rq_clock()->assert_clock_updated()
on p.
Fix this by updating the clock for a non_contending task in
migrate_task_rq_dl() before calling sub_running_bw().
Reported-by: Bruno Goncalves <bgoncalv@redhat.com>
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Daniel Bristot de Oliveira <bristot@kernel.org>
Acked-by: Juri Lelli <juri.lelli@redhat.com>
Link: https://lore.kernel.org/r/20210804135925.3734605-1-dietmar.eggemann@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe28140b33 ]
We should not clear FLAGS_DMA_ACTIVE before omap_sham_update_dma_stop() is
done calling dma_unmap_sg(). We already clear FLAGS_DMA_ACTIVE at the
end of omap_sham_update_dma_stop().
The early clearing of FLAGS_DMA_ACTIVE is not causing issues as we do not
need to defer anything based on FLAGS_DMA_ACTIVE currently. So this can be
applied as clean-up.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Tero Kristo <kristo@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit caa534c3ba ]
When fuel_gauge_reg_readb()/_writeb() fails, report which register we
were trying to read / write when the error happened.
Also reword the message a bit:
- Drop the axp288 prefix, dev_err() already prints this
- Switch from telegram / abbreviated style to a normal sentence, aligning
the message with those from fuel_gauge_read_*bit_word()
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f95091536f ]
It is possible for sched_getattr() to incorrectly report the state of
the reset_on_fork flag when called on a deadline task.
Indeed, if the flag was set on a deadline task using sched_setattr()
with flags (SCHED_FLAG_RESET_ON_FORK | SCHED_FLAG_KEEP_PARAMS), then
p->sched_reset_on_fork will be set, but __setscheduler() will bail out
early, which means that the dl_se->flags will not get updated by
__setscheduler_params()->__setparam_dl(). Consequently, if
sched_getattr() is then called on the task, __getparam_dl() will
override kattr.sched_flags with the now out-of-date copy in dl_se->flags
and report the stale value to userspace.
To fix this, make sure to only copy the flags that are relevant to
sched_deadline to and from the dl_se->flags field.
Signed-off-by: Quentin Perret <qperret@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20210727101103.2729607-2-qperret@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df6313d707 ]
After calling dma_map_single(), we must also call dma_mapping_error().
This fixes the following warning when compiling with CONFIG_DMA_API_DEBUG:
[ 311.241478] WARNING: CPU: 0 PID: 428 at kernel/dma/debug.c:1027 check_unmap+0x79c/0x96c
[ 311.249547] DMA-API: mxs-dcp 2280000.crypto: device driver failed to check map error[device address=0x00000000860cb080] [size=32 bytes] [mapped as single]
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 048661a1f9 ]
Yanfei reported that setting HANDOFF should not depend on recomputing
@first, only on @first state. Which would then give:
if (ww_ctx || !first)
first = __mutex_waiter_is_first(lock, &waiter);
if (first)
__mutex_set_flag(lock, MUTEX_FLAG_HANDOFF);
But because 'ww_ctx || !first' is basically 'always' and the test for
first is relatively cheap, omit that first branch entirely.
Reported-by: Yanfei Xu <yanfei.xu@windriver.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Waiman Long <longman@redhat.com>
Reviewed-by: Yanfei Xu <yanfei.xu@windriver.com>
Link: https://lore.kernel.org/r/20210630154114.896786297@infradead.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
If the client provides a bytesperline value in try_fmt/s_fmt then
validate it and correct if necessary.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Should start_streaming fail, or buffers be queued during
stop_streaming, they should be returned to the core as QUEUED
and not (as currently) as ERROR.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The video decoder can support decoding interlaced streams, so add
the required plumbing to signal this correctly.
The encoder and ISP do NOT support interlaced data, so trying to
configure an interlaced format on those nodes will be rejected.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Adds enum mmal_interlace_type and struct
mmal_parameter_video_interlace_type to allow for querying the
interlacing mode on decoders.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
In order to effectively guarantee that a V4L2_EVENT_SOURCE_CHANGE
event occurs, adopt a default resolution of 32x32 so that it
is incredibly unlikely to be decoding a stream of that resolution
and therefore failing to note a "change" requiring the event.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The exit path of vc4_hdmi_encoder_pre_crtc_configure() is fairly hard to
maintain given its numerous error conditions.
Switch to a goto based approach to simplify it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Unlike pm_runtime_get_sync(), pm_runtime_resume_and_get() doesn't take a
reference on failure, so we don't need to call pm_runtime_put() on
failure.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Our detect function calls pm_runtime_resume_and_get() and
pm_runtime_put() to make sure the device is properly powered before
trying to access the controller.
However, it also makes sure the HSM clock is properly enabled (and
disabled), which is redundant with what runtime_pm is doing already.
Let's just remove it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The older panel-raspberrypi-touchscreen driver had issues in
that it also controlled the power for the touchscreen without
having an appropriate hook for the touchscreen driver to control
that.
Mainline has now added a Toshiba TC358762 bridge driver, and
a regulator/backlight driver for the ATTiny microcontroller on
the board. That allows clean integration with the touchscreen
driver.
Switch the overlays over to using newer drivers.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
We need independent control of the resets for the panel&bridge,
vs the touch controller.
Expose the reset lines that are on the Atmel's port C via the GPIO
API so that they can be controlled appropriately.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The Atmel was doing a load of automatic sequencing of
control lines, however it was combining the touch controller's
reset with the bridge/panel control.
Change to control the control signals directly rather than
through the automatic POWERON control.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The initial state of the Atmel is not defined, so ensure the
backlight PWM is set to 0 by default.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The driver was using the regmap lock to serialise the
individual accesses, but we really need to protect the
timings of enabling the regulators, including any communication
with the Atmel.
Use a mutex within the driver to control overall accesses to
the Atmel, instead of the regmap lock.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The Atmel is doing some things in the I2C ISR, during which
period it will not respond to further commands. This is
particularly true of the POWERON command.
Increase delays appropriately, and retry should I2C errors be
reported.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
There's no reason why 2 Raspberry Pi DSI displays can't be
attached to a Pi Compute Module, so the backlight names need to
be unique.
Use the parent dev_name. It's not as readable, but is unique.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
If no interrupt is defined then a timer and workqueue are used
to poll the controller.
On remove these were not being cleaned up correctly.
Fixes: ca61fdaba7 "Input: edt-ft5x06: Poll the device if no interrupt is
configured."
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The Raspberry Pi 7" 800x480 panel uses a Toshiba TC358762 DSI
to DPI bridge chip, so there is a requirement for the timings
to be specified for the end panel. Add such a definition.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
rpi_touchscreen_i2c_read returns any errors from i2c_transfer,
or the 8 bit received value.
Check for error values before trying to process the data as
valid.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The panel has a prepare call which is before video starts, and an
enable call which is after.
The Toshiba bridge should be configured before video, so move
the relevant power and initialisation calls to prepare.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
If a call to rpi_touchscreen_i2c_write from rpi_touchscreen_probe
fails before mipi_dsi_device_register_full is called, then
in trying to log the error message if uses ts->dsi->dev when
it is still NULL.
Use ts->i2c->dev instead, which is initialised earlier in probe.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The divider calculations tried to find the divider
just faster than the clock requested. However if
it required a divider of 7 then the for loop
aborted without handling the "error" case, and could
end up with a clock lower than requested.
Correct the loop so that we always have a clock greater
than requested.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
On Pi0-3 the driver allocates a buffer and requests a DMA channel
because the ARM can't write to DSI1's registers directly.
However unbind and the error paths in bind don't release the buffer or
the DMA channel.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The HDMI block can repeat pixels for double clocked modes,
and the firmware is now configuring the block to do this as
the PV is doing it incorrectly when at 2pixels/clock.
If the kernel doesn't reset it then we end up with strange
modes.
Reset MISC_CONTROL.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
commit a729691b54 upstream.
When this platform was relatively new in November 2011, with early BIOS
revisions, a reboot quirk was added in commit 6be30bb7d7 ("x86/reboot:
Blacklist Dell OptiPlex 990 known to require PCI reboot")
However, this quirk (and several others) are open-ended to all BIOS
versions and left no automatic expiry if/when the system BIOS fixed the
issue, meaning that nobody is likely to come along and re-test.
What is really problematic with using PCI reboot as this quirk does, is
that it causes this platform to do a full power down, wait one second,
and then power back on. This is less than ideal if one is using it for
boot testing and/or bisecting kernels when legacy rotating hard disks
are installed.
It was only by chance that the quirk was noticed in dmesg - and when
disabled it turned out that it wasn't required anymore (BIOS A24), and a
default reboot would work fine without the "harshness" of power cycling the
machine (and disks) down and up like the PCI reboot does.
Doing a bit more research, it seems that the "newest" BIOS for which the
issue was reported[1] was version A06, however Dell[2] seemed to suggest
only up to and including version A05, with the A06 having a large number of
fixes[3] listed.
As is typical with a new platform, the initial BIOS updates come frequently
and then taper off (and in this case, with a revival for CPU CVEs); a
search for O990-A<ver>.exe reveals the following dates:
A02 16 Mar 2011
A03 11 May 2011
A06 14 Sep 2011
A07 24 Oct 2011
A10 08 Dec 2011
A14 06 Sep 2012
A16 15 Oct 2012
A18 30 Sep 2013
A19 23 Sep 2015
A20 02 Jun 2017
A23 07 Mar 2018
A24 21 Aug 2018
While it's overkill to flash and test each of the above, it would seem
likely that the issue was contained within A0x BIOS versions, given the
dates above and the dates of issue reports[4] from distros. So rather than
just throw out the quirk entirely, limit the scope to just those early BIOS
versions, in case people are still running systems from 2011 with the
original as-shipped early A0x BIOS versions.
[1] https://lore.kernel.org/lkml/1320373471-3942-1-git-send-email-trenn@suse.de/
[2] https://www.dell.com/support/kbdoc/en-ca/000131908/linux-based-operating-systems-stall-upon-reboot-on-optiplex-390-790-990-systems
[3] https://www.dell.com/support/home/en-ca/drivers/driversdetails?driverid=85j10
[4] https://bugs.launchpad.net/ubuntu/+source/linux/+bug/768039
Fixes: 6be30bb7d7 ("x86/reboot: Blacklist Dell OptiPlex 990 known to require PCI reboot")
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210530162447.996461-4-paul.gortmaker@windriver.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c8774a94e upstream.
User space could ask for very large hash tables, we need to make sure
our size computations wont overflow.
nf_tables_newset() needs to double check the u64 size
will fit into size_t field.
Fixes: 0ed6389c48 ("netfilter: nf_tables: rename set implementations")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a9ed27a764 upstream.
is_flush_rq() is called from bt_iter()/bt_tags_iter(), and runs the
following check:
hctx->fq->flush_rq == req
but the passed hctx from bt_iter()/bt_tags_iter() may be NULL because:
1) memory re-order in blk_mq_rq_ctx_init():
rq->mq_hctx = data->hctx;
...
refcount_set(&rq->ref, 1);
OR
2) tag re-use and ->rqs[] isn't updated with new request.
Fix the issue by re-writing is_flush_rq() as:
return rq->end_io == flush_end_io;
which turns out simpler to follow and immune to data race since we have
ordered WRITE rq->end_io and refcount_set(&rq->ref, 1).
Fixes: 2e315dc07d ("blk-mq: grab rq->refcount before calling ->fn in blk_mq_tagset_busy_iter")
Cc: "Blank-Burian, Markus, Dr." <blankburian@uni-muenster.de>
Cc: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20210818010925.607383-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Cc: Yi Zhang <yi.zhang@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2da19ed50 upstream.
For fixing use-after-free during iterating over requests, we grabbed
request's refcount before calling ->fn in commit 2e315dc07d ("blk-mq:
grab rq->refcount before calling ->fn in blk_mq_tagset_busy_iter").
Turns out this way may cause kernel panic when iterating over one flush
request:
1) old flush request's tag is just released, and this tag is reused by
one new request, but ->rqs[] isn't updated yet
2) the flush request can be re-used for submitting one new flush command,
so blk_rq_init() is called at the same time
3) meantime blk_mq_queue_tag_busy_iter() is called, and old flush request
is retrieved from ->rqs[tag]; when blk_mq_put_rq_ref() is called,
flush_rq->end_io may not be updated yet, so NULL pointer dereference
is triggered in blk_mq_put_rq_ref().
Fix the issue by calling refcount_set(&flush_rq->ref, 1) after
flush_rq->end_io is set. So far the only other caller of blk_rq_init() is
scsi_ioctl_reset() in which the request doesn't enter block IO stack and
the request reference count isn't used, so the change is safe.
Fixes: 2e315dc07d ("blk-mq: grab rq->refcount before calling ->fn in blk_mq_tagset_busy_iter")
Reported-by: "Blank-Burian, Markus, Dr." <blankburian@uni-muenster.de>
Tested-by: "Blank-Burian, Markus, Dr." <blankburian@uni-muenster.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/20210811142624.618598-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Cc: Yi Zhang <yi.zhang@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e10de31428 upstream.
On certain AMD platforms, when the IOMMU performance counter source
(csource) field is zero, power-gating for the counter is enabled, which
prevents write access and returns zero for read access.
This can cause invalid perf result especially when event multiplexing
is needed (i.e. more number of events than available counters) since
the current logic keeps track of the previously read counter value,
and subsequently re-program the counter to continue counting the event.
With power-gating enabled, we cannot gurantee successful re-programming
of the counter.
Workaround this issue by :
1. Modifying the ordering of setting/reading counters and enabing/
disabling csources to only access the counter when the csource
is set to non-zero.
2. Since AMD IOMMU PMU does not support interrupt mode, the logic
can be simplified to always start counting with value zero,
and accumulate the counter value when stopping without the need
to keep track and reprogram the counter with the previously read
counter value.
This has been tested on systems with and without power-gating.
Fixes: 994d6608ef ("iommu/amd: Remove performance counter pre-initialization test")
Suggested-by: Alexander Monakov <amonakov@ispras.ru>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20210504065236.4415-1-suravee.suthikulpanit@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f99185041 upstream.
With commit 439c7183e5 ("serial: 8250: 8250_omap: Disable RX interrupt after DMA enable"),
below warning is seen with W=1 and CONFIG_SERIAL_8250_DMA is disabled:
drivers/tty/serial/8250/8250_omap.c:1199:42: warning: unused variable 'k3_soc_devices' [-Wunused-const-variable]
Fix this by moving the code using k3_soc_devices array to
omap_serial_fill_features_erratas() that handles other errata flags as
well.
Fixes: 439c7183e5 ("serial: 8250: 8250_omap: Disable RX interrupt after DMA enable")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20201111112653.2710-2-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ad69832f3 upstream.
When we free a page whose order is very close to MAX_ORDER and greater
than pageblock_order, it wastes some CPU cycles to increase max_order to
MAX_ORDER one by one and check the pageblock migratetype of that page
repeatedly especially when MAX_ORDER is much larger than pageblock_order.
We also should not be checking migratetype of buddy when "order ==
MAX_ORDER - 1" as the buddy pfn may be invalid, so adjust the condition.
With the new check, we don't need the max_order check anymore, so we
replace it.
Also adjust max_order initialization so that it's lower by one than
previously, which makes the code hopefully more clear.
Link: https://lkml.kernel.org/r/20201204155109.55451-1-songmuchun@bytedance.com
Fixes: d9dddbf556 ("mm/page_alloc: prevent merging between isolated and other pageblocks")
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 161a582bd1 upstream.
clang static analysis reports this problem
mos7720.c:352:2: warning: Undefined or garbage value returned to caller
return d;
^~~~~~~~
In the parport_mos7715_read_data()'s call to read_mos_reg(), 'd' is
only set after the alloc block.
buf = kmalloc(1, GFP_KERNEL);
if (!buf)
return -ENOMEM;
Although the problem is reported in parport_most7715_read_data(),
none of the callee's of read_mos_reg() check the return status.
Make sure to clear the return-value buffer also on allocation failures.
Fixes: 0d130367ab ("USB: serial: mos7720: fix control-message error handling")
Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20210111220904.1035957-1-trix@redhat.com
[ johan: only clear the buffer on errors, amend commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sysfs delay_ms value is calculated live, and it is possible for
the time left to appear to be negative briefly if the timer handling
hasn't completed. Ensure the displayed value never goes below zero,
for the sake of appearances.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
A module parameter "dpc_enable" is added to allow the control of the
sensor's on-board DPC (Defective Pixel Correction) function.
This is a global setting to be configured before using the sensor;
there is no intention that this would ever be changed on-the-fly.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
drm_connector_helper_hpd_irq_event() calls
drm_kms_helper_hotplug_event() with the mode-setting lock taken while
it's supposed to be called without that lock taken.
This results in a lockdep warning, and a deadlock if we were to wake up
a TV through CEC (and possibly other cases).
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
commit 514e976744 upstream.
My local syzbot instance hit memory leak in usb_set_configuration().
The problem was in unputted usb interface. In case of errors after
usb_get_intf() the reference should be putted to correclty free memory
allocated for this interface.
Fixes: ec16dae545 ("V4L/DVB (7019): V4L: add support for Syntek DC1125 webcams")
Cc: stable@vger.kernel.org
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 15db16837a upstream.
Server responds to LOOKUP and other ops (READDIRPLUS/CREATE/MKNOD/...)
with ourarg containing nodeid and generation.
If a fuse inode is found in inode cache with the same nodeid but different
generation, the existing fuse inode should be unhashed and marked "bad" and
a new inode with the new generation should be hashed instead.
This can happen, for example, with passhrough fuse filesystem that returns
the real filesystem ino/generation on lookup and where real inode numbers
can get recycled due to real files being unlinked not via the fuse
passthrough filesystem.
With current code, this situation will not be detected and an old fuse
dentry that used to point to an older generation real inode, can be used to
access a completely new inode, which should be accessed only via the new
dentry.
Note that because the FORGET message carries the nodeid w/o generation, the
server should wait to get FORGET counts for the nlookup counts of the old
and reused inodes combined, before it can free the resources associated to
that nodeid.
Stable backport notes:
* This is not a regression. The bug has been in fuse forever, but only
a certain class of low level fuse filesystems can trigger this bug
* Because there is no way to check if this fix is applied in runtime,
libfuse test_examples.py tests this fix with hardcoded check for
kernel version >= 5.14
* After backport to stable kernel(s), the libfuse test can be updated
to also check minimal stable kernel version(s)
* Depends on "fuse: fix bad inode" which is already applied to stable
kernels v5.4.y and v5.10.y
* Required backporting helper inode_wrong_type()
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-fsdevel/CAOQ4uxi8DymG=JO_sAU+wS8akFdzh+PuXwW3Ebgahd2Nwnh7zA@mail.gmail.com/
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e3e2c4362 upstream.
inode_wrong_type(inode, mode) returns true if setting inode->i_mode
to given value would've changed the inode type. We have enough of
those checks open-coded to make a helper worthwhile.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13d9c6b998 upstream.
ASUS ROG Strix G17 has the very same PCI and codec SSID (1043:103f) as
ASUS TX300, and unfortunately, the existing quirk for TX300 is broken
on ASUS ROG. Actually the device works without the quirk, so we'll
need to clear the quirk before applying for this device.
Since ASUS ROG has a different codec (ALC294 - while TX300 has
ALC282), this patch adds a workaround for the device, just clearing
the codec->fixup_id by checking the codec vendor_id.
It's a bit ugly to add such a workaround there, but it seems to be the
simplest way.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214101
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210820143214.3654-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 222013f9ac ]
Support for cryptoloop has been officially marked broken and deprecated
in favor of dm-crypt (which supports the same broken algorithms if
needed) in Linux 2.6.4 (released in March 2004), and support for it has
been entirely removed from losetup in util-linux 2.23 (released in April
2013). Add a warning and a deprecation schedule.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20210827163250.255325-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9e6ffbc5b ]
kcalloc() is called to allocate memory for m->m_info, and if it fails,
ceph_mdsmap_destroy() behind the label out_err will be called:
ceph_mdsmap_destroy(m);
In ceph_mdsmap_destroy(), m->m_info is dereferenced through:
kfree(m->m_info[i].export_targets);
To fix this possible null-pointer dereference, check m->m_info before the
for loop to free m->m_info[i].export_targets.
[ jlayton: fix up whitespace damage
only kfree(m->m_info) if it's non-NULL ]
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Tuo Li <islituo@gmail.com>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e543468869 ]
Thanks to Kees Cook who detected the problem of memset that starting
from not the first member, but sized for the whole struct.
The better change will be to remove the redundant memset and to clear
only the msix_cnt member.
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Reported-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 85520079af ]
macb_ptp_desc will not return NULL under most circumstances with correct
Kconfig and IP design config register. But for the sake of the extreme
corner case, check for NULL when using the helper. In case of rx_tstamp,
no action is necessary except to return (similar to timestamp disabled)
and warn. In case of TX, return -EINVAL to let the skb be free. Perform
this check before marking skb in progress.
Fixes coverity warning:
(4) Event dereference:
Dereferencing a null pointer "desc_ptp"
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0cd08537d ]
For VFs we should return with an error in case we didn't get the exact
number of msix vectors as we requested.
Not doing that will lead to a crash when starting queues for this VF.
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit bae989c4bc upstream.
The ams_delta_camera_power() function is unused as reports
Clang compilation with omap1_defconfig on linux-next:
arch/arm/mach-omap1/board-ams-delta.c:462:12: warning: unused function 'ams_delta_camera_power' [-Wunused-function]
static int ams_delta_camera_power(struct device *dev, int power)
^
1 warning generated.
The soc_camera support was dropped without removing
ams_delta_camera_power() function, making it unused.
Fixes: ce548396a4 ("media: mach-omap1: board-ams-delta.c: remove soc_camera dependencies")
Signed-off-by: Maciej Falkowski <maciej.falkowski9@gmail.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/1326
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d95f22798 upstream.
Here is the warning converted as error and reported by GCC:
kernel/static_call.c: In function ‘__static_call_update’:
kernel/static_call.c:153:18: error: unused variable ‘mod’ [-Werror=unused-variable]
153 | struct module *mod = site_mod->mod;
| ^~~
cc1: all warnings being treated as errors
make[1]: *** [scripts/Makefile.build:271: kernel/static_call.o] Error 1
This is simply because since recently, we no longer use 'mod' variable
elsewhere if MODULE is unset.
When using 'make tinyconfig' to generate the default kconfig, MODULE is
unset.
There are different ways to fix this warning. Here I tried to minimised
the number of modified lines and not add more #ifdef. We could also move
the declaration of the 'mod' variable inside the if-statement or
directly use site_mod->mod.
Fixes: 698bacefe9 ("static_call: Align static_call_is_init() patching condition")
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20210326105023.2058860-1-matthieu.baerts@tessares.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 064c734986 upstream.
The stat() family of syscalls report the wrong size for encrypted
symlinks, which has caused breakage in several userspace programs.
Fix this by calling fscrypt_symlink_getattr() after ubifs_getattr() for
encrypted symlinks. This function computes the correct size by reading
and decrypting the symlink target (if it's not already cached).
For more details, see the commit which added fscrypt_symlink_getattr().
Fixes: ca7f85be8d ("ubifs: Add support for encrypted symlinks")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210702065350.209646-5-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 461b43a8f9 upstream.
The stat() family of syscalls report the wrong size for encrypted
symlinks, which has caused breakage in several userspace programs.
Fix this by calling fscrypt_symlink_getattr() after f2fs_getattr() for
encrypted symlinks. This function computes the correct size by reading
and decrypting the symlink target (if it's not already cached).
For more details, see the commit which added fscrypt_symlink_getattr().
Fixes: cbaf042a3c ("f2fs crypto: add symlink encryption")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210702065350.209646-4-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c4bca10ce upstream.
The stat() family of syscalls report the wrong size for encrypted
symlinks, which has caused breakage in several userspace programs.
Fix this by calling fscrypt_symlink_getattr() after ext4_getattr() for
encrypted symlinks. This function computes the correct size by reading
and decrypting the symlink target (if it's not already cached).
For more details, see the commit which added fscrypt_symlink_getattr().
Fixes: f348c25232 ("ext4 crypto: add symlink encryption")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210702065350.209646-3-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d187605605 upstream.
Add a helper function fscrypt_symlink_getattr() which will be called
from the various filesystems' ->getattr() methods to read and decrypt
the target of encrypted symlinks in order to report the correct st_size.
Detailed explanation:
As required by POSIX and as documented in various man pages, st_size for
a symlink is supposed to be the length of the symlink target.
Unfortunately, st_size has always been wrong for encrypted symlinks
because st_size is populated from i_size from disk, which intentionally
contains the length of the encrypted symlink target. That's slightly
greater than the length of the decrypted symlink target (which is the
symlink target that userspace usually sees), and usually won't match the
length of the no-key encoded symlink target either.
This hadn't been fixed yet because reporting the correct st_size would
require reading the symlink target from disk and decrypting or encoding
it, which historically has been considered too heavyweight to do in
->getattr(). Also historically, the wrong st_size had only broken a
test (LTP lstat03) and there were no known complaints from real users.
(This is probably because the st_size of symlinks isn't used too often,
and when it is, typically it's for a hint for what buffer size to pass
to readlink() -- which a slightly-too-large size still works for.)
However, a couple things have changed now. First, there have recently
been complaints about the current behavior from real users:
- Breakage in rpmbuild:
https://github.com/rpm-software-management/rpm/issues/1682https://github.com/google/fscrypt/issues/305
- Breakage in toybox cpio:
https://www.mail-archive.com/toybox@lists.landley.net/msg07193.html
- Breakage in libgit2: https://issuetracker.google.com/issues/189629152
(on Android public issue tracker, requires login)
Second, we now cache decrypted symlink targets in ->i_link. Therefore,
taking the performance hit of reading and decrypting the symlink target
in ->getattr() wouldn't be as big a deal as it used to be, since usually
it will just save having to do the same thing later.
Also note that eCryptfs ended up having to read and decrypt symlink
targets in ->getattr() as well, to fix this same issue; see
commit 3a60a1686f ("eCryptfs: Decrypt symlink target for stat size").
So, let's just bite the bullet, and read and decrypt the symlink target
in ->getattr() in order to report the correct st_size. Add a function
fscrypt_symlink_getattr() which the filesystems will call to do this.
(Alternatively, we could store the decrypted size of symlinks on-disk.
But there isn't a great place to do so, and encryption is meant to hide
the original size to some extent; that property would be lost.)
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210702065350.209646-2-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a54c4613da upstream.
The location of the system.data extended attribute can change whenever
xattr_sem is not taken. So we need to recalculate the i_inline_off
field since it mgiht have changed between ext4_write_begin() and
ext4_write_end().
This means that caching i_inline_off is probably not helpful, so in
the long run we should probably get rid of it and shrink the in-memory
ext4 inode slightly, but let's fix the race the simple way for now.
Cc: stable@kernel.org
Fixes: f19d5870cb ("ext4: add normal write support for inline data")
Reported-by: syzbot+13146364637c7363a7de@syzkaller.appspotmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds an overlay to connect the QCA7000 in UART mode via UART0.
The qcauart driver uses the serial device bus instead of deprecated
line disciplines.
Signed-off-by: Stefan Wahren <stefan.wahren@in-tech.com>
commit a2baf4e8bb upstream.
Commit b910eaaaa4 ("bpf: Fix NULL pointer dereference in bpf_get_local_storage()
helper") fixed a bug for bpf_get_local_storage() helper so different tasks
won't mess up with each other's percpu local storage.
The percpu data contains 8 slots so it can hold up to 8 contexts (same or
different tasks), for 8 different program runs, at the same time. This in
general is sufficient. But our internal testing showed the following warning
multiple times:
[...]
warning: WARNING: CPU: 13 PID: 41661 at include/linux/bpf-cgroup.h:193
__cgroup_bpf_run_filter_sock_ops+0x13e/0x180
RIP: 0010:__cgroup_bpf_run_filter_sock_ops+0x13e/0x180
<IRQ>
tcp_call_bpf.constprop.99+0x93/0xc0
tcp_conn_request+0x41e/0xa50
? tcp_rcv_state_process+0x203/0xe00
tcp_rcv_state_process+0x203/0xe00
? sk_filter_trim_cap+0xbc/0x210
? tcp_v6_inbound_md5_hash.constprop.41+0x44/0x160
tcp_v6_do_rcv+0x181/0x3e0
tcp_v6_rcv+0xc65/0xcb0
ip6_protocol_deliver_rcu+0xbd/0x450
ip6_input_finish+0x11/0x20
ip6_input+0xb5/0xc0
ip6_sublist_rcv_finish+0x37/0x50
ip6_sublist_rcv+0x1dc/0x270
ipv6_list_rcv+0x113/0x140
__netif_receive_skb_list_core+0x1a0/0x210
netif_receive_skb_list_internal+0x186/0x2a0
gro_normal_list.part.170+0x19/0x40
napi_complete_done+0x65/0x150
mlx5e_napi_poll+0x1ae/0x680
__napi_poll+0x25/0x120
net_rx_action+0x11e/0x280
__do_softirq+0xbb/0x271
irq_exit_rcu+0x97/0xa0
common_interrupt+0x7f/0xa0
</IRQ>
asm_common_interrupt+0x1e/0x40
RIP: 0010:bpf_prog_1835a9241238291a_tw_egress+0x5/0xbac
? __cgroup_bpf_run_filter_skb+0x378/0x4e0
? do_softirq+0x34/0x70
? ip6_finish_output2+0x266/0x590
? ip6_finish_output+0x66/0xa0
? ip6_output+0x6c/0x130
? ip6_xmit+0x279/0x550
? ip6_dst_check+0x61/0xd0
[...]
Using drgn [0] to dump the percpu buffer contents showed that on this CPU
slot 0 is still available, but slots 1-7 are occupied and those tasks in
slots 1-7 mostly don't exist any more. So we might have issues in
bpf_cgroup_storage_unset().
Further debugging confirmed that there is a bug in bpf_cgroup_storage_unset().
Currently, it tries to unset "current" slot with searching from the start.
So the following sequence is possible:
1. A task is running and claims slot 0
2. Running BPF program is done, and it checked slot 0 has the "task"
and ready to reset it to NULL (not yet).
3. An interrupt happens, another BPF program runs and it claims slot 1
with the *same* task.
4. The unset() in interrupt context releases slot 0 since it matches "task".
5. Interrupt is done, the task in process context reset slot 0.
At the end, slot 1 is not reset and the same process can continue to occupy
slots 2-7 and finally, when the above step 1-5 is repeated again, step 3 BPF
program won't be able to claim an empty slot and a warning will be issued.
To fix the issue, for unset() function, we should traverse from the last slot
to the first. This way, the above issue can be avoided.
The same reverse traversal should also be done in bpf_get_local_storage() helper
itself. Otherwise, incorrect local storage may be returned to BPF program.
[0] https://github.com/osandov/drgn
Fixes: b910eaaaa4 ("bpf: Fix NULL pointer dereference in bpf_get_local_storage() helper")
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210810010413.1976277-1-yhs@fb.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67d69e9d1a upstream.
AUDIT_TRIM is expected to be idempotent, but multiple executions resulted
in a refcount underflow and use-after-free.
git bisect fingered commit fb041bb7c0 ("locking/refcount: Consolidate
implementations of refcount_t") but this patch with its more thorough
checking that wasn't in the x86 assembly code merely exposed a previously
existing tree refcount imbalance in the case of tree trimming code that
was refactored with prune_one() to remove a tree introduced in
commit 8432c70062 ("audit: Simplify locking around untag_chunk()")
Move the put_tree() to cover only the prune_one() case.
Passes audit-testsuite and 3 passes of "auditctl -t" with at least one
directory watch.
Cc: Jan Kara <jack@suse.cz>
Cc: Will Deacon <will@kernel.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Seiji Nishikawa <snishika@redhat.com>
Cc: stable@vger.kernel.org
Fixes: 8432c70062 ("audit: Simplify locking around untag_chunk()")
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Reviewed-by: Jan Kara <jack@suse.cz>
[PM: reformatted/cleaned-up the commit description]
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0efb16294 upstream.
A common implementation of isatty(3) involves calling a ioctl passing
a dummy struct argument and checking whether the syscall failed --
bionic and glibc use TCGETS (passing a struct termios), and musl uses
TIOCGWINSZ (passing a struct winsize). If the FD is a socket, we will
copy sizeof(struct ifreq) bytes of data from the argument and return
-EFAULT if that fails. The result is that the isatty implementations
may return a non-POSIX-compliant value in errno in the case where part
of the dummy struct argument is inaccessible, as both struct termios
and struct winsize are smaller than struct ifreq (at least on arm64).
Although there is usually enough stack space following the argument
on the stack that this did not present a practical problem up to now,
with MTE stack instrumentation it's more likely for the copy to fail,
as the memory following the struct may have a different tag.
Fix the problem by adding an early check for whether the ioctl is a
valid socket ioctl, and return -ENOTTY if it isn't.
Fixes: 44c02a2c3d ("dev_ioctl(): move copyin/copyout to callers")
Link: https://linux-review.googlesource.com/id/I869da6cf6daabc3e4b7b82ac979683ba05e27d4d
Signed-off-by: Peter Collingbourne <pcc@google.com>
Cc: <stable@vger.kernel.org> # 4.19
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a7956e25e upstream.
The kthread_is_per_cpu() construct relies on only being called on
PF_KTHREAD tasks (per the WARN in to_kthread). This gives rise to the
following usage pattern:
if ((p->flags & PF_KTHREAD) && kthread_is_per_cpu(p))
However, as reported by syzcaller, this is broken. The scenario is:
CPU0 CPU1 (running p)
(p->flags & PF_KTHREAD) // true
begin_new_exec()
me->flags &= ~(PF_KTHREAD|...);
kthread_is_per_cpu(p)
to_kthread(p)
WARN(!(p->flags & PF_KTHREAD) <-- *SPLAT*
Introduce __to_kthread() that omits the WARN and is sure to check both
values.
Use this to remove the problematic pattern for kthread_is_per_cpu()
and fix a number of other kthread_*() functions that have similar
issues but are currently not used in ways that would expose the
problem.
Notably kthread_func() is only ever called on 'current', while
kthread_probe_data() is only used for PF_WQ_WORKER, which implies the
task is from kthread_create*().
Fixes: ac687e6e8c ("kthread: Extract KTHREAD_IS_PER_CPU")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Valentin Schneider <Valentin.Schneider@arm.com>
Link: https://lkml.kernel.org/r/YH6WJc825C4P0FCK@hirez.programming.kicks-ass.net
[ Drop the balance_push() hunk as it is not needed. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4571b8c5e upstream.
[BUG]
It's easy to trigger NULL pointer dereference, just by removing a
non-existing device id:
# mkfs.btrfs -f -m single -d single /dev/test/scratch1 \
/dev/test/scratch2
# mount /dev/test/scratch1 /mnt/btrfs
# btrfs device remove 3 /mnt/btrfs
Then we have the following kernel NULL pointer dereference:
BUG: kernel NULL pointer dereference, address: 0000000000000000
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP NOPTI
CPU: 9 PID: 649 Comm: btrfs Not tainted 5.14.0-rc3-custom+ #35
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
RIP: 0010:btrfs_rm_device+0x4de/0x6b0 [btrfs]
btrfs_ioctl+0x18bb/0x3190 [btrfs]
? lock_is_held_type+0xa5/0x120
? find_held_lock.constprop.0+0x2b/0x80
? do_user_addr_fault+0x201/0x6a0
? lock_release+0xd2/0x2d0
? __x64_sys_ioctl+0x83/0xb0
__x64_sys_ioctl+0x83/0xb0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
[CAUSE]
Commit a27a94c2b0 ("btrfs: Make btrfs_find_device_by_devspec return
btrfs_device directly") moves the "missing" device path check into
btrfs_rm_device().
But btrfs_rm_device() itself can have case where it only receives
@devid, with NULL as @device_path.
In that case, calling strcmp() on NULL will trigger the NULL pointer
dereference.
Before that commit, we handle the "missing" case inside
btrfs_find_device_by_devspec(), which will not check @device_path at all
if @devid is provided, thus no way to trigger the bug.
[FIX]
Before calling strcmp(), also make sure @device_path is not NULL.
Fixes: a27a94c2b0 ("btrfs: Make btrfs_find_device_by_devspec return btrfs_device directly")
CC: stable@vger.kernel.org # 5.4+
Reported-by: butt3rflyh4ck <butterflyhuangxx@gmail.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7428022b50 upstream.
When a port leaves a VLAN-aware bridge, the current code does not clear
other ports' matrix field bit. If the bridge is later set to VLAN-unaware
mode, traffic in the bridge may leak to that port.
Remove the VLAN filtering check in mt7530_port_bridge_leave.
Fixes: 474a2ddaa1 ("net: dsa: mt7530: fix VLAN traffic leaks")
Fixes: 83163f7dca ("net: dsa: mediatek: add VLAN support for MT7530")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c9b3caab3 upstream.
It's possible that the interrupt handler for the UCSI driver signals a
connector changes after the handler clears the PENDING bit, but before
it has sent the acknowledge request. The result is that the handler is
invoked yet again, to ack the same connector change.
At least some versions of the Qualcomm UCSI firmware will not handle the
second - "spurious" - acknowledgment gracefully. So make sure to not
clear the pending flag until the change is acknowledged.
Any connector changes coming in after the acknowledgment, that would
have the pending flag incorrectly cleared, would afaict be covered by
the subsequent connector status check.
Fixes: 217504a055 ("usb: typec: ucsi: Work around PPM losing change information")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-By: Benjamin Berg <bberg@redhat.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210516040953.622409-1-bjorn.andersson@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 217504a055 upstream.
Some/many PPMs are simply clearing the change bitfield when a
notification on a port is acknowledge. Unfortunately, doing so means
that any changes between the GET_CONNECTOR_STATUS and ACK_CC_CI commands
is simply lost.
Work around this by re-fetching the connector status afterwards. We can
then infer any changes that we see have happened but that may not be
respresented in the change bitfield.
We end up with the following actions:
1. UCSI_GET_CONNECTOR_STATUS, store result, update unprocessed_changes
2. UCSI_GET_CAM_SUPPORTED, discard result
3. ACK connector change
4. UCSI_GET_CONNECTOR_STATUS, store result
5. Infere lost changes by comparing UCSI_GET_CONNECTOR_STATUS results
6. If PPM reported a new change, then restart in order to ACK
7. Process everything as usual.
The worker is also changed to re-schedule itself if a new change
notification happened while it was running.
Doing this fixes quite commonly occurring issues where e.g. the UCSI
power supply would remain online even thought the ThunderBolt cable was
unplugged.
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Benjamin Berg <bberg@redhat.com>
Link: https://lore.kernel.org/r/20201009144047.505957-3-benjamin@sipsolutions.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b40066c97 upstream.
State transitions from 1->0->1 and N->2->1 callbacks require RCU
synchronization. Rather than performing the RCU synchronization every
time the state change occurs, which is quite slow when many tracepoints
are registered in batch, instead keep a snapshot of the RCU state on the
most recent transitions which belong to a chain, and conditionally wait
for a grace period on the last transition of the chain if one g.p. has
not elapsed since the last snapshot.
This applies to both RCU and SRCU.
This brings the performance regression caused by commit 231264d692
("Fix: tracepoint: static call function vs data state mismatch") back to
what it was originally.
Before this commit:
# trace-cmd start -e all
# time trace-cmd start -p nop
real 0m10.593s
user 0m0.017s
sys 0m0.259s
After this commit:
# trace-cmd start -e all
# time trace-cmd start -p nop
real 0m0.878s
user 0m0.000s
sys 0m0.103s
Link: https://lkml.kernel.org/r/20210805192954.30688-1-mathieu.desnoyers@efficios.com
Link: https://lore.kernel.org/io-uring/4ebea8f0-58c9-e571-fd30-0ce4f6f09c70@samba.org/
Cc: stable@vger.kernel.org
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: "Paul E. McKenney" <paulmck@kernel.org>
Cc: Stefan Metzmacher <metze@samba.org>
Fixes: 231264d692 ("Fix: tracepoint: static call function vs data state mismatch")
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Reviewed-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b5bd67cf6 upstream.
There is a need for a polling interface for SRCU grace
periods, so this commit supplies get_state_synchronize_srcu(),
start_poll_synchronize_srcu(), and poll_state_synchronize_srcu() for this
purpose. The first can be used if future grace periods are inevitable
(perhaps due to a later call_srcu() invocation), the second if future
grace periods might not otherwise happen, and the third to check if a
grace period has elapsed since the corresponding call to either of the
first two.
As with get_state_synchronize_rcu() and cond_synchronize_rcu(),
the return value from either get_state_synchronize_srcu() or
start_poll_synchronize_srcu() must be passed in to a later call to
poll_state_synchronize_srcu().
Link: https://lore.kernel.org/rcu/20201112201547.GF3365678@moria.home.lan/
Reported-by: Kent Overstreet <kent.overstreet@gmail.com>
[ paulmck: Add EXPORT_SYMBOL_GPL() per kernel test robot feedback. ]
[ paulmck: Apply feedback from Neeraj Upadhyay. ]
Link: https://lore.kernel.org/lkml/20201117004017.GA7444@paulmck-ThinkPad-P72/
Reviewed-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 74612a07b8 upstream.
There is a need for a polling interface for SRCU grace periods. This
polling needs to distinguish between an SRCU instance being idle on the
one hand or in the middle of a grace period on the other. This commit
therefore converts the Tiny SRCU srcu_struct structure's srcu_idx from
a defacto boolean to a free-running counter, using the bottom bit to
indicate that a grace period is in progress. The second-from-bottom
bit is thus used as the index returned by srcu_read_lock().
Link: https://lore.kernel.org/rcu/20201112201547.GF3365678@moria.home.lan/
Reported-by: Kent Overstreet <kent.overstreet@gmail.com>
[ paulmck: Fix ->srcu_lock_nesting[] indexing per Neeraj Upadhyay. ]
Reviewed-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a893c711a upstream.
There is a need for a polling interface for SRCU grace periods.
This polling needs to initiate an SRCU grace period without
having to queue (and manage) a callback. This commit therefore
splits the Tiny SRCU call_srcu() function into callback-queuing and
start-grace-period portions, with the latter in a new function named
srcu_gp_start_if_needed().
Link: https://lore.kernel.org/rcu/20201112201547.GF3365678@moria.home.lan/
Reported-by: Kent Overstreet <kent.overstreet@gmail.com>
Reviewed-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5358c9fa54 upstream.
There is a need for a polling interface for SRCU grace
periods, so this commit supplies get_state_synchronize_srcu(),
start_poll_synchronize_srcu(), and poll_state_synchronize_srcu() for this
purpose. The first can be used if future grace periods are inevitable
(perhaps due to a later call_srcu() invocation), the second if future
grace periods might not otherwise happen, and the third to check if a
grace period has elapsed since the corresponding call to either of the
first two.
As with get_state_synchronize_rcu() and cond_synchronize_rcu(),
the return value from either get_state_synchronize_srcu() or
start_poll_synchronize_srcu() must be passed in to a later call to
poll_state_synchronize_srcu().
Link: https://lore.kernel.org/rcu/20201112201547.GF3365678@moria.home.lan/
Reported-by: Kent Overstreet <kent.overstreet@gmail.com>
[ paulmck: Add EXPORT_SYMBOL_GPL() per kernel test robot feedback. ]
[ paulmck: Apply feedback from Neeraj Upadhyay. ]
Link: https://lore.kernel.org/lkml/20201117004017.GA7444@paulmck-ThinkPad-P72/
Reviewed-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29d2bb94a8 upstream.
There is a need for a polling interface for SRCU grace periods.
This polling needs to initiate an SRCU grace period without having
to queue (and manage) a callback. This commit therefore splits the
Tree SRCU __call_srcu() function into callback-initialization and
queuing/start-grace-period portions, with the latter in a new function
named srcu_gp_start_if_needed(). This function may be passed a NULL
callback pointer, in which case it will refrain from queuing anything.
Why have the new function mess with queuing? Locking considerations,
of course!
Link: https://lore.kernel.org/rcu/20201112201547.GF3365678@moria.home.lan/
Reported-by: Kent Overstreet <kent.overstreet@gmail.com>
Reviewed-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f66de7ac48 upstream.
The power_pmu_event_init() callback access per-cpu variable
(cpu_hw_events) to check for event constraints and Branch Stack
(BHRB). Current usage is to disable preemption when accessing the
per-cpu variable, but this does not prevent timer callback from
interrupting event_init. Fix this by using 'local_irq_save/restore'
to make sure the code path is invoked with disabled interrupts.
This change is tested in mambo simulator to ensure that, if a timer
interrupt comes in during the per-cpu access in event_init, it will be
soft masked and replayed later. For testing purpose, introduced a
udelay() in power_pmu_event_init() to make sure a timer interrupt arrives
while in per-cpu variable access code between local_irq_save/resore.
As expected the timer interrupt was replayed later during local_irq_restore
called from power_pmu_event_init. This was confirmed by adding
breakpoint in mambo and checking the backtrace when timer_interrupt
was hit.
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1606814880-1720-1-git-send-email-atrajeev@linux.vnet.ibm.com
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f0e6edcd9 upstream.
Considering the following testcase:
int
foo(int a, int b)
{
for (unsigned i = 0; i < 1000000000; i++)
a += b;
return a;
}
int main()
{
foo (3, 4);
return 0;
}
'perf annotate' displays:
86.52 │40055e: → ja 40056c <foo(int, int)+0x26>
13.37 │400560: mov -0x18(%rbp),%eax
│400563: add %eax,-0x14(%rbp)
│400566: addl $0x1,-0x4(%rbp)
0.11 │40056a: → jmp 400557 <foo(int, int)+0x11>
│40056c: mov -0x14(%rbp),%eax
│40056f: pop %rbp
and the 'ja 40056c' does not link to the location in the function. It's
caused by fact that comma is wrongly parsed, it's part of function
signature.
With my patch I see:
86.52 │ ┌──ja 26
13.37 │ │ mov -0x18(%rbp),%eax
│ │ add %eax,-0x14(%rbp)
│ │ addl $0x1,-0x4(%rbp)
0.11 │ │↑ jmp 11
│26:└─→mov -0x14(%rbp),%eax
and 'o' output prints:
86.52 │4005┌── ↓ ja 40056c <foo(int, int)+0x26>
13.37 │4005│0: mov -0x18(%rbp),%eax
│4005│3: add %eax,-0x14(%rbp)
│4005│6: addl $0x1,-0x4(%rbp)
0.11 │4005│a: ↑ jmp 400557 <foo(int, int)+0x11>
│4005└─→ mov -0x14(%rbp),%eax
On the contrary, compiling the very same file with gcc -x c, the parsing
is fine because function arguments are not displayed:
jmp 400543 <foo+0x1d>
Committer testing:
Before:
$ cat cpp_args_annotate.c
int
foo(int a, int b)
{
for (unsigned i = 0; i < 1000000000; i++)
a += b;
return a;
}
int main()
{
foo (3, 4);
return 0;
}
$ gcc --version |& head -1
gcc (GCC) 10.2.1 20201125 (Red Hat 10.2.1-9)
$ gcc -g cpp_args_annotate.c -o cpp_args_annotate
$ perf record ./cpp_args_annotate
[ perf record: Woken up 2 times to write data ]
[ perf record: Captured and wrote 0.275 MB perf.data (7188 samples) ]
$ perf annotate --stdio2 foo
Samples: 7K of event 'cycles:u', 4000 Hz, Event count (approx.): 7468429289, [percent: local period]
foo() /home/acme/c/cpp_args_annotate
Percent
0000000000401106 <foo>:
foo():
int
foo(int a, int b)
{
push %rbp
mov %rsp,%rbp
mov %edi,-0x14(%rbp)
mov %esi,-0x18(%rbp)
for (unsigned i = 0; i < 1000000000; i++)
movl $0x0,-0x4(%rbp)
↓ jmp 1d
a += b;
13.45 13: mov -0x18(%rbp),%eax
add %eax,-0x14(%rbp)
for (unsigned i = 0; i < 1000000000; i++)
addl $0x1,-0x4(%rbp)
0.09 1d: cmpl $0x3b9ac9ff,-0x4(%rbp)
86.46 ↑ jbe 13
return a;
mov -0x14(%rbp),%eax
}
pop %rbp
← retq
$
I.e. works for C, now lets switch to C++:
$ g++ -g cpp_args_annotate.c -o cpp_args_annotate
$ perf record ./cpp_args_annotate
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.268 MB perf.data (6976 samples) ]
$ perf annotate --stdio2 foo
Samples: 6K of event 'cycles:u', 4000 Hz, Event count (approx.): 7380681761, [percent: local period]
foo() /home/acme/c/cpp_args_annotate
Percent
0000000000401106 <foo(int, int)>:
foo(int, int):
int
foo(int a, int b)
{
push %rbp
mov %rsp,%rbp
mov %edi,-0x14(%rbp)
mov %esi,-0x18(%rbp)
for (unsigned i = 0; i < 1000000000; i++)
movl $0x0,-0x4(%rbp)
cmpl $0x3b9ac9ff,-0x4(%rbp)
86.53 → ja 40112c <foo(int, int)+0x26>
a += b;
13.32 mov -0x18(%rbp),%eax
0.00 add %eax,-0x14(%rbp)
for (unsigned i = 0; i < 1000000000; i++)
addl $0x1,-0x4(%rbp)
0.15 → jmp 401117 <foo(int, int)+0x11>
return a;
mov -0x14(%rbp),%eax
}
pop %rbp
← retq
$
Reproduced.
Now with this patch:
Reusing the C++ built binary, as we can see here:
$ readelf -wi cpp_args_annotate | grep producer
<c> DW_AT_producer : (indirect string, offset: 0x2e): GNU C++14 10.2.1 20201125 (Red Hat 10.2.1-9) -mtune=generic -march=x86-64 -g
$
And furthermore:
$ file cpp_args_annotate
cpp_args_annotate: ELF 64-bit LSB executable, x86-64, version 1 (SYSV), dynamically linked, interpreter /lib64/ld-linux-x86-64.so.2, BuildID[sha1]=4fe3cab260204765605ec630d0dc7a7e93c361a9, for GNU/Linux 3.2.0, with debug_info, not stripped
$ perf buildid-list -i cpp_args_annotate
4fe3cab260204765605ec630d0dc7a7e93c361a9
$ perf buildid-list | grep cpp_args_annotate
4fe3cab260204765605ec630d0dc7a7e93c361a9 /home/acme/c/cpp_args_annotate
$
It now works:
$ perf annotate --stdio2 foo
Samples: 6K of event 'cycles:u', 4000 Hz, Event count (approx.): 7380681761, [percent: local period]
foo() /home/acme/c/cpp_args_annotate
Percent
0000000000401106 <foo(int, int)>:
foo(int, int):
int
foo(int a, int b)
{
push %rbp
mov %rsp,%rbp
mov %edi,-0x14(%rbp)
mov %esi,-0x18(%rbp)
for (unsigned i = 0; i < 1000000000; i++)
movl $0x0,-0x4(%rbp)
11: cmpl $0x3b9ac9ff,-0x4(%rbp)
86.53 ↓ ja 26
a += b;
13.32 mov -0x18(%rbp),%eax
0.00 add %eax,-0x14(%rbp)
for (unsigned i = 0; i < 1000000000; i++)
addl $0x1,-0x4(%rbp)
0.15 ↑ jmp 11
return a;
26: mov -0x14(%rbp),%eax
}
pop %rbp
← retq
$
Signed-off-by: Martin Liška <mliska@suse.cz>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Link: http://lore.kernel.org/lkml/13e1a405-edf9-e4c2-4327-a9b454353730@suse.cz
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 41d5854113 upstream.
I got several memory leak reports from Asan with a simple command. It
was because VDSO is not released due to the refcount. Like in
__dsos_addnew_id(), it should put the refcount after adding to the list.
$ perf record true
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.030 MB perf.data (10 samples) ]
=================================================================
==692599==ERROR: LeakSanitizer: detected memory leaks
Direct leak of 439 byte(s) in 1 object(s) allocated from:
#0 0x7fea52341037 in __interceptor_calloc ../../../../src/libsanitizer/asan/asan_malloc_linux.cpp:154
#1 0x559bce4aa8ee in dso__new_id util/dso.c:1256
#2 0x559bce59245a in __machine__addnew_vdso util/vdso.c:132
#3 0x559bce59245a in machine__findnew_vdso util/vdso.c:347
#4 0x559bce50826c in map__new util/map.c:175
#5 0x559bce503c92 in machine__process_mmap2_event util/machine.c:1787
#6 0x559bce512f6b in machines__deliver_event util/session.c:1481
#7 0x559bce515107 in perf_session__deliver_event util/session.c:1551
#8 0x559bce51d4d2 in do_flush util/ordered-events.c:244
#9 0x559bce51d4d2 in __ordered_events__flush util/ordered-events.c:323
#10 0x559bce519bea in __perf_session__process_events util/session.c:2268
#11 0x559bce519bea in perf_session__process_events util/session.c:2297
#12 0x559bce2e7a52 in process_buildids /home/namhyung/project/linux/tools/perf/builtin-record.c:1017
#13 0x559bce2e7a52 in record__finish_output /home/namhyung/project/linux/tools/perf/builtin-record.c:1234
#14 0x559bce2ed4f6 in __cmd_record /home/namhyung/project/linux/tools/perf/builtin-record.c:2026
#15 0x559bce2ed4f6 in cmd_record /home/namhyung/project/linux/tools/perf/builtin-record.c:2858
#16 0x559bce422db4 in run_builtin /home/namhyung/project/linux/tools/perf/perf.c:313
#17 0x559bce2acac8 in handle_internal_command /home/namhyung/project/linux/tools/perf/perf.c:365
#18 0x559bce2acac8 in run_argv /home/namhyung/project/linux/tools/perf/perf.c:409
#19 0x559bce2acac8 in main /home/namhyung/project/linux/tools/perf/perf.c:539
#20 0x7fea51e76d09 in __libc_start_main ../csu/libc-start.c:308
Indirect leak of 32 byte(s) in 1 object(s) allocated from:
#0 0x7fea52341037 in __interceptor_calloc ../../../../src/libsanitizer/asan/asan_malloc_linux.cpp:154
#1 0x559bce520907 in nsinfo__copy util/namespaces.c:169
#2 0x559bce50821b in map__new util/map.c:168
#3 0x559bce503c92 in machine__process_mmap2_event util/machine.c:1787
#4 0x559bce512f6b in machines__deliver_event util/session.c:1481
#5 0x559bce515107 in perf_session__deliver_event util/session.c:1551
#6 0x559bce51d4d2 in do_flush util/ordered-events.c:244
#7 0x559bce51d4d2 in __ordered_events__flush util/ordered-events.c:323
#8 0x559bce519bea in __perf_session__process_events util/session.c:2268
#9 0x559bce519bea in perf_session__process_events util/session.c:2297
#10 0x559bce2e7a52 in process_buildids /home/namhyung/project/linux/tools/perf/builtin-record.c:1017
#11 0x559bce2e7a52 in record__finish_output /home/namhyung/project/linux/tools/perf/builtin-record.c:1234
#12 0x559bce2ed4f6 in __cmd_record /home/namhyung/project/linux/tools/perf/builtin-record.c:2026
#13 0x559bce2ed4f6 in cmd_record /home/namhyung/project/linux/tools/perf/builtin-record.c:2858
#14 0x559bce422db4 in run_builtin /home/namhyung/project/linux/tools/perf/perf.c:313
#15 0x559bce2acac8 in handle_internal_command /home/namhyung/project/linux/tools/perf/perf.c:365
#16 0x559bce2acac8 in run_argv /home/namhyung/project/linux/tools/perf/perf.c:409
#17 0x559bce2acac8 in main /home/namhyung/project/linux/tools/perf/perf.c:539
#18 0x7fea51e76d09 in __libc_start_main ../csu/libc-start.c:308
SUMMARY: AddressSanitizer: 471 byte(s) leaked in 2 allocation(s).
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20210315045641.700430-1-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67069a1f0f upstream.
ASan reported a memory leak caused by info_linear not being deallocated.
The info_linear was allocated during in perf_event__synthesize_one_bpf_prog().
This patch adds the corresponding free() when bpf_prog_info_node
is freed in perf_env__purge_bpf().
$ sudo ./perf record -- sleep 5
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.025 MB perf.data (8 samples) ]
=================================================================
==297735==ERROR: LeakSanitizer: detected memory leaks
Direct leak of 7688 byte(s) in 19 object(s) allocated from:
#0 0x4f420f in malloc (/home/user/linux/tools/perf/perf+0x4f420f)
#1 0xc06a74 in bpf_program__get_prog_info_linear /home/user/linux/tools/lib/bpf/libbpf.c:11113:16
#2 0xb426fe in perf_event__synthesize_one_bpf_prog /home/user/linux/tools/perf/util/bpf-event.c:191:16
#3 0xb42008 in perf_event__synthesize_bpf_events /home/user/linux/tools/perf/util/bpf-event.c:410:9
#4 0x594596 in record__synthesize /home/user/linux/tools/perf/builtin-record.c:1490:8
#5 0x58c9ac in __cmd_record /home/user/linux/tools/perf/builtin-record.c:1798:8
#6 0x58990b in cmd_record /home/user/linux/tools/perf/builtin-record.c:2901:8
#7 0x7b2a20 in run_builtin /home/user/linux/tools/perf/perf.c:313:11
#8 0x7b12ff in handle_internal_command /home/user/linux/tools/perf/perf.c:365:8
#9 0x7b2583 in run_argv /home/user/linux/tools/perf/perf.c:409:2
#10 0x7b0d79 in main /home/user/linux/tools/perf/perf.c:539:3
#11 0x7fa357ef6b74 in __libc_start_main /usr/src/debug/glibc-2.33-8.fc34.x86_64/csu/../csu/libc-start.c:332:16
Signed-off-by: Riccardo Mancini <rickyman7@gmail.com>
Acked-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Andrii Nakryiko <andrii@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: KP Singh <kpsingh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: Yonghong Song <yhs@fb.com>
Link: http://lore.kernel.org/lkml/20210602224024.300485-1-rickyman7@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 55981d3541 upstream.
Some USB BT adapters don't satisfy the MTU requirement mentioned in
commit e848dbd364 ("Bluetooth: btusb: Add support USB ALT 3 for WBS")
and have ALT 3 setting that produces no/garbled audio. Some adapters
with larger MTU were also reported to have problems with ALT 3.
Add a flag and check it and MTU before selecting ALT 3, falling back to
ALT 1. Enable the flag for Realtek, restoring the previous behavior for
non-Realtek devices.
Tested with USB adapters (mtu<72, no/garbled sound with ALT3, ALT1
works) BCM20702A1 0b05:17cb, CSR8510A10 0a12:0001, and (mtu>=72, ALT3
works) RTL8761BU 0bda:8771, Intel AX200 8087:0029 (after disabling
ALT6). Also got reports for (mtu>=72, ALT 3 reported to produce bad
audio) Intel 8087:0a2b.
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Fixes: e848dbd364 ("Bluetooth: btusb: Add support USB ALT 3 for WBS")
Tested-by: Michał Kępień <kernel@kempniu.pl>
Tested-by: Jonathan Lampérth <jon@h4n.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7387a72c5f upstream.
__tipc_sendmsg() is called to send SYN packet by either tipc_sendmsg()
or tipc_connect(). The difference is in tipc_connect(), it will call
tipc_wait_for_connect() after __tipc_sendmsg() to wait until connecting
is done. So there's no need to wait in __tipc_sendmsg() for this case.
This patch is to fix it by calling tipc_wait_for_connect() only when dlen
is not 0 in __tipc_sendmsg(), which means it's called by tipc_connect().
Note this also fixes the failure in tipcutils/test/ptts/:
# ./tipcTS &
# ./tipcTC 9
(hang)
Fixes: 36239dab6da7 ("tipc: fix implicit-connect for SYN+")
Reported-by: Shuang Li <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new generic NAND ECC framework stores the configuration and
requirements in separate places since commit 93ef92f6f4 ("mtd: nand: Use
the new generic ECC object"). In 5.10.x The SPI NAND layer still uses only
the requirements to track the ECC properties. This mismatch leads to
values of zero being used for ECC strength and step_size in the SPI NAND
layer wherever nanddev_get_ecc_conf() is used and therefore breaks the SPI
NAND on-die ECC support in 5.10.x.
By using nanddev_get_ecc_requirements() instead of nanddev_get_ecc_conf()
for SPI NAND, we make sure that the correct parameters for the detected
chip are used. In later versions (5.11.x) this is fixed anyway with the
implementation of the SPI NAND on-die ECC engine.
Cc: stable@vger.kernel.org # 5.10.x
Reported-by: voice INTER connect GmbH <developer@voiceinterconnect.de>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe67f4dd8d upstream.
It turns out that the SIGIO/FASYNC situation is almost exactly the same
as the EPOLLET case was: user space really wants to be notified after
every operation.
Now, in a perfect world it should be sufficient to only notify user
space on "state transitions" when the IO state changes (ie when a pipe
goes from unreadable to readable, or from unwritable to writable). User
space should then do as much as possible - fully emptying the buffer or
what not - and we'll notify it again the next time the state changes.
But as with EPOLLET, we have at least one case (stress-ng) where the
kernel sent SIGIO due to the pipe being marked for asynchronous
notification, but the user space signal handler then didn't actually
necessarily read it all before returning (it read more than what was
written, but since there could be multiple writes, it could leave data
pending).
The user space code then expected to get another SIGIO for subsequent
writes - even though the pipe had been readable the whole time - and
would only then read more.
This is arguably a user space bug - and Colin King already fixed the
stress-ng code in question - but the kernel regression rules are clear:
it doesn't matter if kernel people think that user space did something
silly and wrong. What matters is that it used to work.
So if user space depends on specific historical kernel behavior, it's a
regression when that behavior changes. It's on us: we were silly to
have that non-optimal historical behavior, and our old kernel behavior
was what user space was tested against.
Because of how the FASYNC notification was tied to wakeup behavior, this
was first broken by commits f467a6a664 and 1b6b26ae70 ("pipe: fix
and clarify pipe read/write wakeup logic"), but at the time it seems
nobody noticed. Probably because the stress-ng problem case ends up
being timing-dependent too.
It was then unwittingly fixed by commit 3a34b13a88 ("pipe: make pipe
writes always wake up readers") only to be broken again when by commit
3b844826b6 ("pipe: avoid unnecessary EPOLLET wakeups under normal
loads").
And at that point the kernel test robot noticed the performance
refression in the stress-ng.sigio.ops_per_sec case. So the "Fixes" tag
below is somewhat ad hoc, but it matches when the issue was noticed.
Fix it for good (knock wood) by simply making the kill_fasync() case
separate from the wakeup case. FASYNC is quite rare, and we clearly
shouldn't even try to use the "avoid unnecessary wakeups" logic for it.
Link: https://lore.kernel.org/lkml/20210824151337.GC27667@xsang-OptiPlex-9020/
Fixes: 3b844826b6 ("pipe: avoid unnecessary EPOLLET wakeups under normal loads")
Reported-by: kernel test robot <oliver.sang@intel.com>
Tested-by: Oliver Sang <oliver.sang@intel.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b844826b6 upstream.
I had forgotten just how sensitive hackbench is to extra pipe wakeups,
and commit 3a34b13a88 ("pipe: make pipe writes always wake up
readers") ended up causing a quite noticeable regression on larger
machines.
Now, hackbench isn't necessarily a hugely meaningful benchmark, and it's
not clear that this matters in real life all that much, but as Mel
points out, it's used often enough when comparing kernels and so the
performance regression shows up like a sore thumb.
It's easy enough to fix at least for the common cases where pipes are
used purely for data transfer, and you never have any exciting poll
usage at all. So set a special 'poll_usage' flag when there is polling
activity, and make the ugly "EPOLLET has crazy legacy expectations"
semantics explicit to only that case.
I would love to limit it to just the broken EPOLLET case, but the pipe
code can't see the difference between epoll and regular select/poll, so
any non-read/write waiting will trigger the extra wakeup behavior. That
is sufficient for at least the hackbench case.
Apart from making the odd extra wakeup cases more explicitly about
EPOLLET, this also makes the extra wakeup be at the _end_ of the pipe
write, not at the first write chunk. That is actually much saner
semantics (as much as you can call any of the legacy edge-triggered
expectations for EPOLLET "sane") since it means that you know the wakeup
will happen once the write is done, rather than possibly in the middle
of one.
[ For stable people: I'm putting a "Fixes" tag on this, but I leave it
up to you to decide whether you actually want to backport it or not.
It likely has no impact outside of synthetic benchmarks - Linus ]
Link: https://lore.kernel.org/lkml/20210802024945.GA8372@xsang-OptiPlex-9020/
Fixes: 3a34b13a88 ("pipe: make pipe writes always wake up readers")
Reported-by: kernel test robot <oliver.sang@intel.com>
Tested-by: Sandeep Patil <sspatil@android.com>
Tested-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc0939fcfa upstream.
We have a race between marking that an inode needs to be logged, either
at btrfs_set_inode_last_trans() or at btrfs_page_mkwrite(), and between
btrfs_sync_log(). The following steps describe how the race happens.
1) We are at transaction N;
2) Inode I was previously fsynced in the current transaction so it has:
inode->logged_trans set to N;
3) The inode's root currently has:
root->log_transid set to 1
root->last_log_commit set to 0
Which means only one log transaction was committed to far, log
transaction 0. When a log tree is created we set ->log_transid and
->last_log_commit of its parent root to 0 (at btrfs_add_log_tree());
4) One more range of pages is dirtied in inode I;
5) Some task A starts an fsync against some other inode J (same root), and
so it joins log transaction 1.
Before task A calls btrfs_sync_log()...
6) Task B starts an fsync against inode I, which currently has the full
sync flag set, so it starts delalloc and waits for the ordered extent
to complete before calling btrfs_inode_in_log() at btrfs_sync_file();
7) During ordered extent completion we have btrfs_update_inode() called
against inode I, which in turn calls btrfs_set_inode_last_trans(),
which does the following:
spin_lock(&inode->lock);
inode->last_trans = trans->transaction->transid;
inode->last_sub_trans = inode->root->log_transid;
inode->last_log_commit = inode->root->last_log_commit;
spin_unlock(&inode->lock);
So ->last_trans is set to N and ->last_sub_trans set to 1.
But before setting ->last_log_commit...
8) Task A is at btrfs_sync_log():
- it increments root->log_transid to 2
- starts writeback for all log tree extent buffers
- waits for the writeback to complete
- writes the super blocks
- updates root->last_log_commit to 1
It's a lot of slow steps between updating root->log_transid and
root->last_log_commit;
9) The task doing the ordered extent completion, currently at
btrfs_set_inode_last_trans(), then finally runs:
inode->last_log_commit = inode->root->last_log_commit;
spin_unlock(&inode->lock);
Which results in inode->last_log_commit being set to 1.
The ordered extent completes;
10) Task B is resumed, and it calls btrfs_inode_in_log() which returns
true because we have all the following conditions met:
inode->logged_trans == N which matches fs_info->generation &&
inode->last_subtrans (1) <= inode->last_log_commit (1) &&
inode->last_subtrans (1) <= root->last_log_commit (1) &&
list inode->extent_tree.modified_extents is empty
And as a consequence we return without logging the inode, so the
existing logged version of the inode does not point to the extent
that was written after the previous fsync.
It should be impossible in practice for one task be able to do so much
progress in btrfs_sync_log() while another task is at
btrfs_set_inode_last_trans() right after it reads root->log_transid and
before it reads root->last_log_commit. Even if kernel preemption is enabled
we know the task at btrfs_set_inode_last_trans() can not be preempted
because it is holding the inode's spinlock.
However there is another place where we do the same without holding the
spinlock, which is in the memory mapped write path at:
vm_fault_t btrfs_page_mkwrite(struct vm_fault *vmf)
{
(...)
BTRFS_I(inode)->last_trans = fs_info->generation;
BTRFS_I(inode)->last_sub_trans = BTRFS_I(inode)->root->log_transid;
BTRFS_I(inode)->last_log_commit = BTRFS_I(inode)->root->last_log_commit;
(...)
So with preemption happening after setting ->last_sub_trans and before
setting ->last_log_commit, it is less of a stretch to have another task
do enough progress at btrfs_sync_log() such that the task doing the memory
mapped write ends up with ->last_sub_trans and ->last_log_commit set to
the same value. It is still a big stretch to get there, as the task doing
btrfs_sync_log() has to start writeback, wait for its completion and write
the super blocks.
So fix this in two different ways:
1) For btrfs_set_inode_last_trans(), simply set ->last_log_commit to the
value of ->last_sub_trans minus 1;
2) For btrfs_page_mkwrite() only set the inode's ->last_sub_trans, just
like we do for buffered and direct writes at btrfs_file_write_iter(),
which is all we need to make sure multiple writes and fsyncs to an
inode in the same transaction never result in an fsync missing that
the inode changed and needs to be logged. Turn this into a helper
function and use it both at btrfs_page_mkwrite() and at
btrfs_file_write_iter() - this also fixes the problem that at
btrfs_page_mkwrite() we were setting those fields without the
protection of the inode's spinlock.
This is an extremely unlikely race to happen in practice.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fb4b1373dc ]
Function "dma_map_sg" is entitled to merge adjacent entries
and return a value smaller than what was passed as "nents".
Subsequently "ib_map_mr_sg" needs to work with this value ("sg_dma_len")
rather than the original "nents" parameter ("sg_len").
This old RDS bug was exposed and reliably causes kernel panics
(using RDMA operations "rds-stress -D") on x86_64 starting with:
commit c588072bba ("iommu/vt-d: Convert intel iommu driver to the iommu ops")
Simply put: Linux 5.11 and later.
Signed-off-by: Gerd Rausch <gerd.rausch@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Link: https://lore.kernel.org/r/60efc69f-1f35-529d-a7ef-da0549cad143@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6eaa1f3c59 ]
When booted with multiple displays attached, the EFI GOP driver on (at
least) Ampere, can leave DP links powered up that aren't being used to
display anything. This confuses our tracking of SOR routing, with the
likely result being a failed modeset and display engine hang.
Fix this by (ab?)using the DisableLT IED script to power-down the link,
restoring HW to a state the driver expects.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa0b1ef5f7 ]
[Why]
Userspace should get back a copy of drm_wait_vblank that's been modified
even when drm_wait_vblank_ioctl returns a failure.
Rationale:
drm_wait_vblank_ioctl modifies the request and expects the user to read
it back. When the type is RELATIVE, it modifies it to ABSOLUTE and updates
the sequence to become current_vblank_count + sequence (which was
RELATIVE), but now it became ABSOLUTE.
drmWaitVBlank (in libdrm) expects this to be the case as it modifies
the request to be Absolute so it expects the sequence to would have been
updated.
The change is in compat_drm_wait_vblank, which is called by
drm_compat_ioctl. This change of copying the data back regardless of the
return number makes it en par with drm_ioctl, which always copies the
data before returning.
[How]
Return from the function after everything has been copied to user.
Fixes IGT:kms_flip::modeset-vs-vblank-race-interruptible
Tested on ChromeOS Trogdor(msm)
Reviewed-by: Michel Dänzer <mdaenzer@redhat.com>
Signed-off-by: Mark Yacoub <markyacoub@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210812194917.1703356-1-markyacoub@chromium.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37110237f3 ]
Avoiding qed ll2 race condition and NULL pointer dereference as part
of the remove and recovery flows.
Changes form V1:
- Change (!p_rx->set_prod_addr).
- qed_ll2.c checkpatch fixes.
Change from V2:
- Revert "qed_ll2.c checkpatch fixes".
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a24ce06c70 ]
We use a spinlock now so add a stub.
Ignore bogus uninitialized variable warnings.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e74cfa91f4 ]
As __vringh_iov() traverses a descriptor chain, it populates
each descriptor entry into either read or write vring iov
and increments that iov's ->used member. So, as we iterate
over a descriptor chain, at any point, (riov/wriov)->used
value gives the number of descriptor enteries available,
which are to be read or written by the device. As all read
iovs must precede the write iovs, wiov->used should be zero
when we are traversing a read descriptor. Current code checks
for wiov->i, to figure out whether any previous entry in the
current descriptor chain was a write descriptor. However,
iov->i is only incremented, when these vring iovs are consumed,
at a later point, and remain 0 in __vringh_iov(). So, correct
the check for read and write descriptor order, to use
wiov->used.
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Link: https://lore.kernel.org/r/1624591502-4827-1-git-send-email-neeraju@codeaurora.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43bb40c5b9 ]
When a virtio pci device undergo surprise removal (aka async removal in
PCIe spec), mark the device as broken so that any upper layer drivers can
abort any outstanding operation.
When a virtio net pci device undergo surprise removal which is used by a
NetworkManager, a below call trace was observed.
kernel:watchdog: BUG: soft lockup - CPU#1 stuck for 26s! [kworker/1:1:27059]
watchdog: BUG: soft lockup - CPU#1 stuck for 52s! [kworker/1:1:27059]
CPU: 1 PID: 27059 Comm: kworker/1:1 Tainted: G S W I L 5.13.0-hotplug+ #8
Hardware name: Dell Inc. PowerEdge R640/0H28RR, BIOS 2.9.4 11/06/2020
Workqueue: events linkwatch_event
RIP: 0010:virtnet_send_command+0xfc/0x150 [virtio_net]
Call Trace:
virtnet_set_rx_mode+0xcf/0x2a7 [virtio_net]
? __hw_addr_create_ex+0x85/0xc0
__dev_mc_add+0x72/0x80
igmp6_group_added+0xa7/0xd0
ipv6_mc_up+0x3c/0x60
ipv6_find_idev+0x36/0x80
addrconf_add_dev+0x1e/0xa0
addrconf_dev_config+0x71/0x130
addrconf_notify+0x1f5/0xb40
? rtnl_is_locked+0x11/0x20
? __switch_to_asm+0x42/0x70
? finish_task_switch+0xaf/0x2c0
? raw_notifier_call_chain+0x3e/0x50
raw_notifier_call_chain+0x3e/0x50
netdev_state_change+0x67/0x90
linkwatch_do_dev+0x3c/0x50
__linkwatch_run_queue+0xd2/0x220
linkwatch_event+0x21/0x30
process_one_work+0x1c8/0x370
worker_thread+0x30/0x380
? process_one_work+0x370/0x370
kthread+0x118/0x140
? set_kthread_struct+0x40/0x40
ret_from_fork+0x1f/0x30
Hence, add the ability to abort the command on surprise removal
which prevents infinite loop and system lockup.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Link: https://lore.kernel.org/r/20210721142648.1525924-5-parav@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60f0779862 ]
Currently vq->broken field is read by virtqueue_is_broken() in busy
loop in one context by virtnet_send_command().
vq->broken is set to true in other process context by
virtio_break_device(). Reader and writer are accessing it without any
synchronization. This may lead to a compiler optimization which may
result to optimize reading vq->broken only once.
Hence, force reading vq->broken on each invocation of
virtqueue_is_broken() and also force writing it so that such
update is visible to the readers.
It is a theoretical fix that isn't yet encountered in the field.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Link: https://lore.kernel.org/r/20210721142648.1525924-2-parav@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 335ffab3ef ]
This WARN can be triggered per-core and the stack trace is not useful.
Replace it with plain dev_err(). Fix a comment while at it.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1669a941f7 ]
The probe was manually passing NULL instead of dev to devm_clk_hw_register.
This caused a Unable to handle kernel NULL pointer dereference error.
Fix this by passing 'dev'.
Signed-off-by: Adam Ford <aford173@gmail.com>
Fixes: a20a40a8bb ("clk: renesas: rcar-usb2-clock-sel: Fix error handling in .probe()")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b3a8738b7 ]
The u32 variable pci_dword is being masked with 0x1fffffff and then left
shifted 23 places. The shift is a u32 operation,so a value of 0x200 or
more in pci_dword will overflow the u32 and only the bottow 32 bits
are assigned to addr. I don't believe this was the original intent.
Fix this by casting pci_dword to a resource_size_t to ensure no
overflow occurs.
Note that the mask and 12 bit left shift operation does not need this
because the mask SNR_IMC_MMIO_MEM0_MASK and shift is always a 32 bit
value.
Fixes: ee49532b38 ("perf/x86/intel/uncore: Add IMC uncore support for Snow Ridge")
Addresses-Coverity: ("Unintentional integer overflow")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Link: https://lore.kernel.org/r/20210706114553.28249-1-colin.king@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c8094e394 ]
When the schema fixups are applied to 'select' the result is a single
entry is required for a match, but that will never match as there should
be 2 entries. Also, a 'select' schema should have the widest possible
match, so use 'contains' which matches the compatible string(s) in any
position and not just the first position.
Fixes: 993dcfac64 ("dt-bindings: riscv: sifive-l2-cache: convert bindings to json-schema")
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 82a44ae113 ]
In the case of taprio offload is not enabled, the error handling path
causes a kernel crash due to kernel NULL pointer deference.
Fix this by adding check for NULL before attempt to access 'plat->est'
on the mutex_lock() call.
The following kernel panic is observed without this patch:
RIP: 0010:mutex_lock+0x10/0x20
Call Trace:
tc_setup_taprio+0x482/0x560 [stmmac]
kmem_cache_alloc_trace+0x13f/0x490
taprio_disable_offload.isra.0+0x9d/0x180 [sch_taprio]
taprio_destroy+0x6c/0x100 [sch_taprio]
qdisc_create+0x2e5/0x4f0
tc_modify_qdisc+0x126/0x740
rtnetlink_rcv_msg+0x12b/0x380
_raw_spin_lock_irqsave+0x19/0x40
_raw_spin_unlock_irqrestore+0x18/0x30
create_object+0x212/0x340
rtnl_calcit.isra.0+0x110/0x110
netlink_rcv_skb+0x50/0x100
netlink_unicast+0x191/0x230
netlink_sendmsg+0x243/0x470
sock_sendmsg+0x5e/0x60
____sys_sendmsg+0x20b/0x280
copy_msghdr_from_user+0x5c/0x90
__mod_memcg_state+0x87/0xf0
___sys_sendmsg+0x7c/0xc0
lru_cache_add+0x7f/0xa0
_raw_spin_unlock+0x16/0x30
wp_page_copy+0x449/0x890
handle_mm_fault+0x921/0xfc0
__sys_sendmsg+0x59/0xa0
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xa9
---[ end trace b1f19b24368a96aa ]---
Fixes: b60189e039 ("net: stmmac: Integrate EST with TAPRIO scheduler API")
Cc: <stable@vger.kernel.org> # 5.10.x
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2aae654a4 ]
Add a mutex lock to protect est structure parameters so that the
EST parameters can be updated by other threads.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pavel Machek (CIP) <pavel@denx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 885814a97f ]
This reverts commit 419dd626e3.
It turned out that the change from the reverted commit breaks the ACPI
based rpi's because it causes the 100Mhz max clock to be overridden to the
return from sdhci_iproc_get_max_clock(), which is 0 because there isn't a
OF/DT based clock device.
Reported-by: Jeremy Linton <jeremy.linton@arm.com>
Fixes: 419dd626e3 ("mmc: sdhci-iproc: Set SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN on BCM2711")
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c1671e0d1 ]
Currently, when query PFC configuration by dcbtool, driver will return
PFC enable status based on TC. As all priorities are mapped to TC0 by
default, if TC0 is enabled, then all priorities mapped to TC0 will be
shown as enabled status when query PFC setting, even though some
priorities have never been set.
for example:
$ dcb pfc show dev eth0
pfc-cap 4 macsec-bypass off delay 0
prio-pfc 0:off 1:off 2:off 3:off 4:off 5:off 6:off 7:off
$ dcb pfc set dev eth0 prio-pfc 0:on 1:on 2:on 3:on
$ dcb pfc show dev eth0
pfc-cap 4 macsec-bypass off delay 0
prio-pfc 0:on 1:on 2:on 3:on 4:on 5:on 6:on 7:on
To fix this problem, just returns user's PFC config parameter saved in
driver.
Fixes: cacde272dd ("net: hns3: Add hclge_dcb module for the support of DCB feature")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94391fae82 ]
VLAN list should not be added duplicate VLAN node, otherwise it would
cause "add failed" when restore VLAN from VLAN list, so this patch adds
VLAN ID check before adding node into VLAN list.
Fixes: c6075b1934 ("net: hns3: Record VF vlan tables")
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a96d9330b0 ]
After the cmdq registers are cleared, the firmware may take time to
clear out possible left over commands in the cmdq. Driver must release
cmdq memory only after firmware has completed processing of left over
commands.
Fixes: 232d0d55fc ("net: hns3: uninitialize command queue while unloading PF driver")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a6d281946 ]
If a PF is bonded to a virtual machine and the virtual machine exits
unexpectedly, some hardware resource cannot be cleared. In this case,
loading driver may cause exceptions. Therefore, the hardware resource
needs to be cleared when the driver is loaded.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 96a6b93b69 ]
Currently when device is moved between network namespaces using
RTM_NEWLINK message type and one of netns attributes (FLA_NET_NS_PID,
IFLA_NET_NS_FD, IFLA_TARGET_NETNSID) but w/o specifying IFLA_IFNAME, and
target namespace already has device with same name, userspace will get
EINVAL what is confusing and makes debugging harder.
Fix it so that userspace gets more appropriate EEXIST instead what makes
debugging much easier.
Before:
# ./ifname.sh
+ ip netns add ns0
+ ip netns exec ns0 ip link add l0 type dummy
+ ip netns exec ns0 ip link show l0
8: l0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 66:90:b5:d5:78:69 brd ff:ff:ff:ff:ff:ff
+ ip link add l0 type dummy
+ ip link show l0
10: l0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 6e:c6:1f:15:20:8d brd ff:ff:ff:ff:ff:ff
+ ip link set l0 netns ns0
RTNETLINK answers: Invalid argument
After:
# ./ifname.sh
+ ip netns add ns0
+ ip netns exec ns0 ip link add l0 type dummy
+ ip netns exec ns0 ip link show l0
8: l0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 1e:4a:72:e3:e3:8f brd ff:ff:ff:ff:ff:ff
+ ip link add l0 type dummy
+ ip link show l0
10: l0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether f2:fc:fe:2b:7d:a6 brd ff:ff:ff:ff:ff:ff
+ ip link set l0 netns ns0
RTNETLINK answers: File exists
The problem is that do_setlink() passes its `char *ifname` argument,
that it gets from a caller, to __dev_change_net_namespace() as is (as
`const char *pat`), but semantics of ifname and pat can be different.
For example, __rtnl_newlink() does this:
net/core/rtnetlink.c
3270 char ifname[IFNAMSIZ];
...
3286 if (tb[IFLA_IFNAME])
3287 nla_strscpy(ifname, tb[IFLA_IFNAME], IFNAMSIZ);
3288 else
3289 ifname[0] = '\0';
...
3364 if (dev) {
...
3394 return do_setlink(skb, dev, ifm, extack, tb, ifname, status);
3395 }
, i.e. do_setlink() gets ifname pointer that is always valid no matter
if user specified IFLA_IFNAME or not and then do_setlink() passes this
ifname pointer as is to __dev_change_net_namespace() as pat argument.
But the pat (pattern) in __dev_change_net_namespace() is used as:
net/core/dev.c
11198 err = -EEXIST;
11199 if (__dev_get_by_name(net, dev->name)) {
11200 /* We get here if we can't use the current device name */
11201 if (!pat)
11202 goto out;
11203 err = dev_get_valid_name(net, dev, pat);
11204 if (err < 0)
11205 goto out;
11206 }
As the result the `goto out` path on line 11202 is neven taken and
instead of returning EEXIST defined on line 11198,
__dev_change_net_namespace() returns an error from dev_get_valid_name()
and this, in turn, will be EINVAL for ifname[0] = '\0' set earlier.
Fixes: d8a5ec6727 ("[NET]: netlink support for moving devices between network namespaces.")
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43fed4d48d ]
When adapter init fails, the blocked freelist bitmap is already freed
up and should not be touched. So, move the bitmap zeroing closer to
where it was successfully allocated. Also handle adapter init failure
unwind path immediately and avoid setting up RDMA memory windows.
Fixes: 5b377d114f ("cxgb4: Add debugfs facility to inject FL starvation")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6457378fe7 ]
A group of security researchers brought to our attention
the weakness of hash function used in fnhe_hashfun().
Lets use siphash instead of Jenkins Hash, to considerably
reduce security risks.
Also remove the inline keyword, this really is distracting.
Fixes: d546c62154 ("ipv4: harden fnhe_hashfun()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Keyu Man <kman001@ucr.edu>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4785305c05 ]
A group of security researchers brought to our attention
the weakness of hash function used in rt6_exception_hash()
Lets use siphash instead of Jenkins Hash, to considerably
reduce security risks.
Following patch deals with IPv4.
Fixes: 35732d01fe ("ipv6: introduce a hash table to store dst cache")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Keyu Man <kman001@ucr.edu>
Cc: Wei Wang <weiwan@google.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Acked-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd9b50adc6 ]
While running kselftests, Hangbin observed that sch_ets.sh often crashes,
and splats like the following one are seen in the output of 'dmesg':
BUG: kernel NULL pointer dereference, address: 0000000000000000
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 159f12067 P4D 159f12067 PUD 159f13067 PMD 0
Oops: 0000 [#1] SMP NOPTI
CPU: 2 PID: 921 Comm: tc Not tainted 5.14.0-rc6+ #458
Hardware name: Red Hat KVM, BIOS 1.11.1-4.module+el8.1.0+4066+0f1aadab 04/01/2014
RIP: 0010:__list_del_entry_valid+0x2d/0x50
Code: 48 8b 57 08 48 b9 00 01 00 00 00 00 ad de 48 39 c8 0f 84 ac 6e 5b 00 48 b9 22 01 00 00 00 00 ad de 48 39 ca 0f 84 cf 6e 5b 00 <48> 8b 32 48 39 fe 0f 85 af 6e 5b 00 48 8b 50 08 48 39 f2 0f 85 94
RSP: 0018:ffffb2da005c3890 EFLAGS: 00010217
RAX: 0000000000000000 RBX: ffff9073ba23f800 RCX: dead000000000122
RDX: 0000000000000000 RSI: 0000000000000008 RDI: ffff9073ba23fbc8
RBP: ffff9073ba23f890 R08: 0000000000000001 R09: 0000000000000001
R10: 0000000000000001 R11: 0000000000000001 R12: dead000000000100
R13: ffff9073ba23fb00 R14: 0000000000000002 R15: 0000000000000002
FS: 00007f93e5564e40(0000) GS:ffff9073bba00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 000000014ad34000 CR4: 0000000000350ee0
Call Trace:
ets_qdisc_reset+0x6e/0x100 [sch_ets]
qdisc_reset+0x49/0x1d0
tbf_reset+0x15/0x60 [sch_tbf]
qdisc_reset+0x49/0x1d0
dev_reset_queue.constprop.42+0x2f/0x90
dev_deactivate_many+0x1d3/0x3d0
dev_deactivate+0x56/0x90
qdisc_graft+0x47e/0x5a0
tc_get_qdisc+0x1db/0x3e0
rtnetlink_rcv_msg+0x164/0x4c0
netlink_rcv_skb+0x50/0x100
netlink_unicast+0x1a5/0x280
netlink_sendmsg+0x242/0x480
sock_sendmsg+0x5b/0x60
____sys_sendmsg+0x1f2/0x260
___sys_sendmsg+0x7c/0xc0
__sys_sendmsg+0x57/0xa0
do_syscall_64+0x3a/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f93e44b8338
Code: 89 02 48 c7 c0 ff ff ff ff eb b5 0f 1f 80 00 00 00 00 f3 0f 1e fa 48 8d 05 25 43 2c 00 8b 00 85 c0 75 17 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 58 c3 0f 1f 80 00 00 00 00 41 54 41 89 d4 55
RSP: 002b:00007ffc0db737a8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 0000000061255c06 RCX: 00007f93e44b8338
RDX: 0000000000000000 RSI: 00007ffc0db73810 RDI: 0000000000000003
RBP: 0000000000000000 R08: 0000000000000001 R09: 0000000000000000
R10: 000000000000000b R11: 0000000000000246 R12: 0000000000000001
R13: 0000000000687880 R14: 0000000000000000 R15: 0000000000000000
Modules linked in: sch_ets sch_tbf dummy rfkill iTCO_wdt iTCO_vendor_support intel_rapl_msr intel_rapl_common joydev i2c_i801 pcspkr i2c_smbus lpc_ich virtio_balloon ip_tables xfs libcrc32c crct10dif_pclmul crc32_pclmul crc32c_intel ahci libahci ghash_clmulni_intel libata serio_raw virtio_blk virtio_console virtio_net net_failover failover sunrpc dm_mirror dm_region_hash dm_log dm_mod
CR2: 0000000000000000
When the change() function decreases the value of 'nstrict', we must take
into account that packets might be already enqueued on a class that flips
from 'strict' to 'quantum': otherwise that class will not be added to the
bandwidth-sharing list. Then, a call to ets_qdisc_reset() will attempt to
do list_del(&alist) with 'alist' filled with zero, hence the NULL pointer
dereference.
For classes flipping from 'strict' to 'quantum', initialize an empty list
and eventually add it to the bandwidth-sharing list, if there are packets
already enqueued. In this way, the kernel will:
a) prevent crashing as described above.
b) avoid retaining the backlog packets (for an arbitrarily long time) in
case no packet is enqueued after a change from 'strict' to 'quantum'.
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Fixes: dcc68b4d80 ("net: sch_ets: Add a new Qdisc")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 359f4cdd7d ]
According to Armada XP datasheet bit at 0 position is corresponding for
TxInProg indication.
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Signed-off-by: Maxim Kiselev <bigunclemax@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ed74b03eb ]
A successful 'xge_mdio_config()' call should be balanced by a corresponding
'xge_mdio_remove()' call in the error handling path of the probe, as
already done in the remove function.
Update the error handling path accordingly.
Fixes: ea8ab16ab2 ("drivers: net: xgene-v2: Add MDIO support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44a13a5d99 ]
We should decode the latency and the max_latency before directly compare.
The latency should be presented as lat_enc = scale x value:
lat_enc_d = (lat_enc & 0x0x3ff) x (1U << (5*((max_ltr_enc & 0x1c00)
>> 10)))
Fixes: cf8fb73c23 ("e1000e: add support for LTR on I217/I218")
Suggested-by: Yee Li <seven.yi.lee@gmail.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b79959510 ]
After unplug thunderbolt dock with i225, pciehp interrupt is triggered,
remove call will read/write mmio address which is already disconnected,
then cause page fault and make system hang.
Check PCI state to remove device safely.
Trace:
BUG: unable to handle page fault for address: 000000000000b604
Oops: 0000 [#1] SMP NOPTI
RIP: 0010:igc_rd32+0x1c/0x90 [igc]
Call Trace:
igc_ptp_suspend+0x6c/0xa0 [igc]
igc_ptp_stop+0x12/0x50 [igc]
igc_remove+0x7f/0x1c0 [igc]
pci_device_remove+0x3e/0xb0
__device_release_driver+0x181/0x240
Fixes: 13b5b7fd6a ("igc: Add support for Tx/Rx rings")
Fixes: b03c49cde6 ("igc: Save PTP time before a reset")
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ffc9c3ebb4 ]
- restore the behavior in enable_net_traffic() to avoid regressions - Jakub
Kicinski;
- hurried up and removed redundant assignment in pegasus_open() before yet
another checker complains;
Fixes: 8a160e2e9a ("net: usb: pegasus: Check the return value of get_geristers() and friends;")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Petko Manolov <petko.manolov@konsulko.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8f89fa277 ]
The devlink dev info command reports version information about the
device and firmware running on the board. This includes the "board.id"
field which is supposed to represent an identifier of the board design.
The ice driver uses the Product Board Assembly identifier for this.
In some cases, the PBA is not present in the NVM. If this happens,
devlink dev info will fail with an error. Instead, modify the
ice_info_pba function to just exit without filling in the context
buffer. This will cause the board.id field to be skipped. Log a dev_dbg
message in case someone wants to confirm why board.id is not showing up
for them.
Fixes: e961b679fb ("ice: add board identifier info to devlink .info_get")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20210819223451.245613-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbe71c6199 ]
kmalloc_array() is called to allocate memory for tx->descp. If it fails,
the function __sdma_txclean() is called:
__sdma_txclean(dd, tx);
However, in the function __sdma_txclean(), tx-descp is dereferenced if
tx->num_desc is not zero:
sdma_unmap_desc(dd, &tx->descp[0]);
To fix this possible null-pointer dereference, assign the return value of
kmalloc_array() to a local variable descp, and then assign it to tx->descp
if it is not NULL. Otherwise, go to enomem.
Fixes: 7724105686 ("IB/hfi1: add driver files")
Link: https://lore.kernel.org/r/20210806133029.194964-1-islituo@gmail.com
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Tuo Li <islituo@gmail.com>
Tested-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 02c6dcd543 upstream.
We found a hang, the steps to reproduce are as follows:
1. blocking device via scsi_device_set_state()
2. dd if=/dev/sda of=/mnt/t.log bs=1M count=10
3. echo none > /sys/block/sda/queue/scheduler
4. echo "running" >/sys/block/sda/device/state
Step 3 and 4 should complete after step 4, but they hang.
CPU#0 CPU#1 CPU#2
--------------- ---------------- ----------------
Step 1: blocking device
Step 2: dd xxxx
^^^^^^ get request
q_usage_counter++
Step 3: switching scheculer
elv_iosched_store
elevator_switch
blk_mq_freeze_queue
blk_freeze_queue
> blk_freeze_queue_start
^^^^^^ mq_freeze_depth++
> blk_mq_run_hw_queues
^^^^^^ can't run queue when dev blocked
> blk_mq_freeze_queue_wait
^^^^^^ Hang here!!!
wait q_usage_counter==0
Step 4: running device
store_state_field
scsi_rescan_device
scsi_attach_vpd
scsi_vpd_inquiry
__scsi_execute
blk_get_request
blk_mq_alloc_request
blk_queue_enter
^^^^^^ Hang here!!!
wait mq_freeze_depth==0
blk_mq_run_hw_queues
^^^^^^ dispatch IO, q_usage_counter will reduce to zero
blk_mq_unfreeze_queue
^^^^^ mq_freeze_depth--
To fix this, we need to run queue before rescanning device when the device
state changes to SDEV_RUNNING.
Link: https://lore.kernel.org/r/20210824025921.3277629-1-lijinlin3@huawei.com
Fixes: f0f82e2476 ("scsi: core: Fix capacity set to zero after offlinining device")
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Li Jinlin <lijinlin3@huawei.com>
Signed-off-by: Qiu Laibin <qiulaibin@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a1e25c0a0 upstream.
During a USB cable disconnect, or soft disconnect scenario, a pending
SETUP transaction may not be completed, leading to the following
error:
dwc3 a600000.dwc3: timed out waiting for SETUP phase
If this occurs, then the entire pullup disable routine is skipped and
proper cleanup and halting of the controller does not complete.
Instead of returning an error (which is ignored from the UDC
perspective), allow the pullup disable routine to continue, which
will also handle disabling of EP0/1. This will end any active
transfers as well. Ensure to clear any delayed_status also, as the
timeout could happen within the STATUS stage.
Fixes: bb01473648 ("usb: dwc3: gadget: don't clear RUN/STOP when it's invalid to do so")
Cc: <stable@vger.kernel.org>
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/20210825042855.7977-1-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51f1954ad8 upstream.
We can't depend on the TRB's HWO bit to determine if the TRB ring is
"full". A TRB is only available when the driver had processed it, not
when the controller consumed and relinquished the TRB's ownership to the
driver. Otherwise, the driver may overwrite unprocessed TRBs. This can
happen when many transfer events accumulate and the system is slow to
process them and/or when there are too many small requests.
If a request is in the started_list, that means there is one or more
unprocessed TRBs remained. Check this instead of the TRB's HWO bit
whether the TRB ring is full.
Fixes: c4233573f6 ("usb: dwc3: gadget: prepare TRBs on update transfers too")
Cc: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/e91e975affb0d0d02770686afc3a5b9eb84409f6.1629335416.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c82cacd2f1 upstream.
The recent attempt to handle an unknown ROM state in the commit
d143825baf ("usb: renesas-xhci: Fix handling of unknown ROM state")
resulted in a regression and reverted later by the commit 44cf53602f
("Revert "usb: renesas-xhci: Fix handling of unknown ROM state"").
The problem of the former fix was that it treated the failure of
firmware loading as a fatal error. Since the firmware files aren't
included in the standard linux-firmware tree, most users don't have
them, hence they got the non-working system after that. The revert
fixed the regression, but also it didn't make the firmware loading
triggered even on the devices that do need it. So we need still a fix
for them.
This is another attempt to handle the unknown ROM state. Like the
previous fix, this also tries to load the firmware when ROM shows
unknown state. In this patch, however, the failure of a firmware
loading (such as a missing firmware file) isn't handled as a fatal
error any longer when ROM has been already detected, but it falls back
to the ROM mode like before. The error is returned only when no ROM
is detected and the firmware loading failed.
Along with it, for simplifying the code flow, the detection and the
check of ROM is factored out from renesas_fw_check_running() and done
in the caller side, renesas_xhci_check_request_fw(). It avoids the
redundant ROM checks.
The patch was tested on Lenovo Thinkpad T14 gen (BIOS 1.34). Also it
was confirmed that no regression is seen on another Thinkpad T14
machine that has worked without the patch, too.
Fixes: 44cf53602f ("Revert "usb: renesas-xhci: Fix handling of unknown ROM state"")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://bugzilla.opensuse.org/show_bug.cgi?id=1189207
Link: https://lore.kernel.org/r/20210826124127.14789-1-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32bc8f8373 upstream.
schedule_delayed_work does not push back the work if it was already
scheduled before, so amdgpu_device_delay_enable_gfx_off ran ~100 ms
after the first time GFXOFF was disabled and re-enabled, even if GFXOFF
was disabled and re-enabled again during those 100 ms.
This resulted in frame drops / stutter with the upcoming mutter 41
release on Navi 14, due to constantly enabling GFXOFF in the HW and
disabling it again (for getting the GPU clock counter).
To fix this, call cancel_delayed_work_sync when the disable count
transitions from 0 to 1, and only schedule the delayed work on the
reverse transition, not if the disable count was already 0. This makes
sure the delayed work doesn't run at unexpected times, and allows it to
be lock-free.
v2:
* Use cancel_delayed_work_sync & mutex_trylock instead of
mod_delayed_work.
v3:
* Make amdgpu_device_delay_enable_gfx_off lock-free (Christian König)
v4:
* Fix race condition between amdgpu_gfx_off_ctrl incrementing
adev->gfx.gfx_off_req_count and amdgpu_device_delay_enable_gfx_off
checking for it to be 0 (Evan Quan)
Cc: stable@vger.kernel.org
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com> # v3
Acked-by: Christian König <christian.koenig@amd.com> # v3
Signed-off-by: Michel Dänzer <mdaenzer@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e9655763b upstream.
This reverts commit f216562731.
[BUG]
It's no longer possible to create compressed inline extent after commit
f216562731 ("btrfs: compression: don't try to compress if we don't
have enough pages").
[CAUSE]
For compression code, there are several possible reasons we have a range
that needs to be compressed while it's no more than one page.
- Compressed inline write
The data is always smaller than one sector and the test lacks the
condition to properly recognize a non-inline extent.
- Compressed subpage write
For the incoming subpage compressed write support, we require page
alignment of the delalloc range.
And for 64K page size, we can compress just one page into smaller
sectors.
For those reasons, the requirement for the data to be more than one page
is not correct, and is already causing regression for compressed inline
data writeback. The idea of skipping one page to avoid wasting CPU time
could be revisited in the future.
[FIX]
Fix it by reverting the offending commit.
Reported-by: Zygo Blaxell <ce3g8jdj@umail.furryterror.org>
Link: https://lore.kernel.org/linux-btrfs/afa2742.c084f5d6.17b6b08dffc@tnonline.net
Fixes: f216562731 ("btrfs: compression: don't try to compress if we don't have enough pages")
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 379eb01c21 upstream.
The value of FP registers in the core dump file comes from the
thread.fstate. However, kernel saves the FP registers to the thread.fstate
only before scheduling out the process. If no process switch happens
during the exception handling process, kernel will not have a chance to
save the latest value of FP registers to thread.fstate. It will cause the
value of FP registers in the core dump file may be incorrect. To solve this
problem, this patch force lets kernel save the FP register into the
thread.fstate if the target task_struct equals the current.
Signed-off-by: Vincent Chen <vincent.chen@sifive.com>
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Fixes: b8c8a9590e ("RISC-V: Add FP register ptrace support for gdb.")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2f9fa1f3b upstream.
The ceph_cap_flush structures are usually dynamically allocated, but
the ceph_cap_snap has an embedded one.
When force umounting, the client will try to remove all the session
caps. During this, it will free them, but that should not be done
with the ones embedded in a capsnap.
Fix this by adding a new boolean that indicates that the cap flush is
embedded in a capsnap, and skip freeing it if that's set.
At the same time, switch to using list_del_init() when detaching the
i_list and g_list heads. It's possible for a forced umount to remove
these objects but then handle_cap_flushsnap_ack() races in and does the
list_del_init() again, corrupting memory.
Cc: stable@vger.kernel.org
URL: https://tracker.ceph.com/issues/52283
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 48c812e032 ]
The ocelot driver makes use of regmap, wrapping it with driver specific
operations that are thin wrappers around the core regmap APIs. These are
exported with EXPORT_SYMBOL, dropping the _GPL from the core regmap
exports which is frowned upon. Add _GPL suffixes to at least the APIs that
are doing register I/O.
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 580c610429 ]
One error path can result in release_dentry_name_snapshot() being called
before "name" was initialized by take_dentry_name_snapshot().
Fix by moving the release_dentry_name_snapshot() to immediately after the
only use.
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4608fdfc07 ]
Michal Kubecek reports that conntrack gc is responsible for frequent
wakeups (every 125ms) on idle systems.
On busy systems, timed out entries are evicted during lookup.
The gc worker is only needed to remove entries after system becomes idle
after a busy period.
To resolve this, always scan the entire table.
If the scan is taking too long, reschedule so other work_structs can run
and resume from next bucket.
After a completed scan, wait for 2 minutes before the next cycle.
Heuristics for faster re-schedule are removed.
GC_SCAN_INTERVAL could be exposed as a sysctl in the future to allow
tuning this as-needed or even turn the gc worker off.
Reported-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf79167fd8 ]
Enabling CONFIG_STACKDEPOT results in the following build error.
arc-elf-ld: lib/stackdepot.o: in function `filter_irq_stacks':
stackdepot.c:(.text+0x456): undefined reference to `__irqentry_text_start'
arc-elf-ld: stackdepot.c:(.text+0x456): undefined reference to `__irqentry_text_start'
arc-elf-ld: stackdepot.c:(.text+0x476): undefined reference to `__irqentry_text_end'
arc-elf-ld: stackdepot.c:(.text+0x476): undefined reference to `__irqentry_text_end'
arc-elf-ld: stackdepot.c:(.text+0x484): undefined reference to `__softirqentry_text_start'
arc-elf-ld: stackdepot.c:(.text+0x484): undefined reference to `__softirqentry_text_start'
arc-elf-ld: stackdepot.c:(.text+0x48c): undefined reference to `__softirqentry_text_end'
arc-elf-ld: stackdepot.c:(.text+0x48c): undefined reference to `__softirqentry_text_end'
Other architectures address this problem by adding IRQENTRY_TEXT and
SOFTIRQENTRY_TEXT to the text segment, so do the same here.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31428c7874 ]
When the component level pin control functions were added they for some
no longer obvious reason handled adding prefixing of widget names. This
meant that when the lack of prefix handling in the DAPM level pin
operations was fixed by ae4fc53224 (ASoC: dapm: use component
prefix when checking widget names) the one device using the component
level API ended up with the prefix being applied twice, causing all
lookups to fail.
Fix this by removing the redundant prefixing from the component code,
which has the nice side effect of also making that code much simpler.
Reported-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Tested-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210726194123.54585-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b910eaaaa4 upstream.
Jiri Olsa reported a bug ([1]) in kernel where cgroup local
storage pointer may be NULL in bpf_get_local_storage() helper.
There are two issues uncovered by this bug:
(1). kprobe or tracepoint prog incorrectly sets cgroup local storage
before prog run,
(2). due to change from preempt_disable to migrate_disable,
preemption is possible and percpu storage might be overwritten
by other tasks.
This issue (1) is fixed in [2]. This patch tried to address issue (2).
The following shows how things can go wrong:
task 1: bpf_cgroup_storage_set() for percpu local storage
preemption happens
task 2: bpf_cgroup_storage_set() for percpu local storage
preemption happens
task 1: run bpf program
task 1 will effectively use the percpu local storage setting by task 2
which will be either NULL or incorrect ones.
Instead of just one common local storage per cpu, this patch fixed
the issue by permitting 8 local storages per cpu and each local
storage is identified by a task_struct pointer. This way, we
allow at most 8 nested preemption between bpf_cgroup_storage_set()
and bpf_cgroup_storage_unset(). The percpu local storage slot
is released (calling bpf_cgroup_storage_unset()) by the same task
after bpf program finished running.
bpf_test_run() is also fixed to use the new bpf_cgroup_storage_set()
interface.
The patch is tested on top of [2] with reproducer in [1].
Without this patch, kernel will emit error in 2-3 minutes.
With this patch, after one hour, still no error.
[1] https://lore.kernel.org/bpf/CAKH8qBuXCfUz=w8L+Fj74OaUpbosO29niYwTki7e3Ag044_aww@mail.gmail.com/T
[2] https://lore.kernel.org/bpf/20210309185028.3763817-1-yhs@fb.com
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Roman Gushchin <guro@fb.com>
Link: https://lore.kernel.org/bpf/20210323055146.3334476-1-yhs@fb.com
Cc: <stable@vger.kernel.org> # 5.10.x
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5b029a32cf upstream.
Commit 457f44363a ("bpf: Implement BPF ring buffer and verifier support
for it") extended check_map_func_compatibility() by enforcing map -> helper
function match, but not helper -> map type match.
Due to this all of the bpf_ringbuf_*() helper functions could be used with
a wrong map type such as array or hash map, leading to invalid access due
to type confusion.
Also, both BPF_FUNC_ringbuf_{submit,discard} have ARG_PTR_TO_ALLOC_MEM as
argument and not a BPF map. Therefore, their check_map_func_compatibility()
presence is incorrect since it's only for map type checking.
Fixes: 457f44363a ("bpf: Implement BPF ring buffer and verifier support for it")
Reported-by: Ryota Shiga (Flatt Security)
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e78c597c3 upstream.
This check was incomplete, did not consider size is 0:
if (len != ALIGN(size, 4) + hdrlen)
goto err;
if size from qrtr_hdr is 0, the result of ALIGN(size, 4)
will be 0, In case of len == hdrlen and size == 0
in header this check won't fail and
if (cb->type == QRTR_TYPE_NEW_SERVER) {
/* Remote node endpoint can bridge other distant nodes */
const struct qrtr_ctrl_pkt *pkt = data + hdrlen;
qrtr_node_assign(node, le32_to_cpu(pkt->server.node));
}
will also read out of bound from data, which is hdrlen allocated block.
Fixes: 194ccc8829 ("net: qrtr: Support decoding incoming v2 packets")
Fixes: ad9d24c942 ("net: qrtr: fix OOB Read in qrtr_endpoint_post")
Signed-off-by: Xiaolong Huang <butterflyhuangxx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ upstream commit 21f965221e ]
If an SQPOLL based ring is newly created and an application issues an
io_uring_enter(2) system call on it, then we can return a spurious
-EOWNERDEAD error. This happens because there's nothing to submit, and
if the caller doesn't specify any other action, the initial error
assignment of -EOWNERDEAD never gets overwritten. This causes us to
return it directly, even if it isn't valid.
Move the error assignment into the actual failure case instead.
Cc: stable@vger.kernel.org
Fixes: d9d05217cb ("io_uring: stop SQPOLL submit on creator's death")
Reported-by: Sherlock Holo sherlockya@gmail.com
Link: https://github.com/axboe/liburing/issues/413
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ upstream commit a30f895ad3 ]
We currently check for ret != 0 to indicate error, but '1' is a valid
return and just indicates that the allocation succeeded with a wrap.
Correct the check to be for < 0, like it was before the xarray
conversion.
Cc: stable@vger.kernel.org
Fixes: 61cf93700f ("io_uring: Convert personality_idr to XArray")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fdd92b64d1 ]
We've had CONFIG_MANDATORY_FILE_LOCKING since 2015 and a lot of distros
have disabled it. Warn the stragglers that still use "-o mand" that
we'll be dropping support for that mount option.
Cc: stable@vger.kernel.org
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f56ce412a5 ]
We've noticed occasional OOM killing when memory.low settings are in
effect for cgroups. This is unexpected and undesirable as memory.low is
supposed to express non-OOMing memory priorities between cgroups.
The reason for this is proportional memory.low reclaim. When cgroups
are below their memory.low threshold, reclaim passes them over in the
first round, and then retries if it couldn't find pages anywhere else.
But when cgroups are slightly above their memory.low setting, page scan
force is scaled down and diminished in proportion to the overage, to the
point where it can cause reclaim to fail as well - only in that case we
currently don't retry, and instead trigger OOM.
To fix this, hook proportional reclaim into the same retry logic we have
in place for when cgroups are skipped entirely. This way if reclaim
fails and some cgroups were scanned with diminished pressure, we'll try
another full-force cycle before giving up and OOMing.
[akpm@linux-foundation.org: coding-style fixes]
Link: https://lkml.kernel.org/r/20210817180506.220056-1-hannes@cmpxchg.org
Fixes: 9783aa9917 ("mm, memcg: proportional memory.{low,min} reclaim")
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reported-by: Leon Yang <lnyng@fb.com>
Reviewed-by: Rik van Riel <riel@surriel.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Roman Gushchin <guro@fb.com>
Acked-by: Chris Down <chris@chrisdown.name>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: <stable@vger.kernel.org> [5.4+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65ca89c2b1 ]
The commit 2e6b836312 ("ASoC: intel: atom: Fix reference to PCM
buffer address") changed the reference of PCM buffer address to
substream->runtime->dma_addr as the buffer address may change
dynamically. However, I forgot that the dma_addr field is still not
set up for the CONTINUOUS buffer type (that this driver uses) yet in
5.14 and earlier kernels, and it resulted in garbage I/O. The problem
will be fixed in 5.15, but we need to address it quickly for now.
The fix is to deduce the address again from the DMA pointer with
virt_to_phys(), but from the right one, substream->runtime->dma_area.
Fixes: 2e6b836312 ("ASoC: intel: atom: Fix reference to PCM buffer address")
Reported-and-tested-by: Hans de Goede <hdegoede@redhat.com>
Cc: <stable@vger.kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/2048c6aa-2187-46bd-6772-36a4fb3c5aeb@redhat.com
Link: https://lore.kernel.org/r/20210819152945.8510-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a671f77ee ]
The struct pci_dev uses reference counting but zPCI assumed erroneously
that the last reference would always be the local reference after
calling pci_stop_and_remove_bus_device(). This is usually the case but
not how reference counting works and thus inherently fragile.
In fact one case where this causes a NULL pointer dereference when on an
SRIOV device the function 0 was hot unplugged before another function of
the same multi-function device. In this case the second function's
pdev->sriov->dev reference keeps the struct pci_dev of function 0 alive
even after the unplug. This bug was previously hidden by the fact that
we were leaking the struct pci_dev which in turn means that it always
outlived the struct zpci_dev. This was fixed in commit 0b13525c20
("s390/pci: fix leak of PCI device structure") exposing the broken
behavior.
Fix this by accounting for the long living reference a struct pci_dev
has to its underlying struct zpci_dev via the zbus->function[] array and
only release that in pcibios_release_device() ensuring that the struct
pci_dev is not left with a dangling reference. This is a minimal fix in
the future it would probably better to use fine grained reference
counting for struct zpci_dev.
Fixes: 05bc1be6db ("s390/pci: create zPCI bus")
Cc: stable@vger.kernel.org
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57a1681095 ]
The function tpci200_register called by tpci200_install and
tpci200_unregister called by tpci200_uninstall are in pair. However,
tpci200_unregister has some cleanup operations not in the
tpci200_register. So the error handling code of tpci200_pci_probe has
many different double free issues.
Fix this problem by moving those cleanup operations out of
tpci200_unregister, into tpci200_pci_remove and reverting
the previous commit 9272e5d002 ("ipack/carriers/tpci200:
Fix a double free in tpci200_pci_probe").
Fixes: 9272e5d002 ("ipack/carriers/tpci200: Fix a double free in tpci200_pci_probe")
Cc: stable@vger.kernel.org
Reported-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Link: https://lore.kernel.org/r/20210810100323.3938492-1-mudongliangabcd@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a263c1ff6a ]
In some usecases transaction ids are dynamically allocated inside
the controller driver after sending the messages which have generic
acknowledge responses. So check for this before refcounting pm_runtime.
Without this we would end up imbalancing runtime pm count by
doing pm_runtime_put() in both slim_do_transfer() and slim_msg_response()
for a single pm_runtime_get() in slim_do_transfer()
Fixes: d3062a2109 ("slimbus: messaging: add slim_alloc/free_txn_tid()")
Cc: <stable@vger.kernel.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210809082428.11236-3-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9711759a87 ]
As GDSCs are registered and found to be already enabled gdsc_init()
ensures that 1) the kernel state matches the hardware state, and 2)
votable GDSCs are properly enabled from this master as well.
But as the (optional) supply regulator is enabled deep into
gdsc_toggle_logic(), which is only executed for votable GDSCs, the
kernel's state of the regulator might not match the hardware. The
regulator might be automatically turned off if no other users are
present or the next call to gdsc_disable() would cause an unbalanced
regulator_disable().
Given that the votable case deals with an already enabled GDSC, most of
gdsc_enable() and gdsc_toggle_logic() can be skipped. Reduce it to just
clearing the SW_COLLAPSE_MASK and enabling hardware control to simply
call regulator_enable() in both cases.
The enablement of hardware control seems to be an independent property
from the GDSC being enabled, so this is moved outside that conditional
segment.
Lastly, as the propagation of ALWAYS_ON to GENPD_FLAG_ALWAYS_ON needs to
happen regardless of the initial state this is grouped together with the
other sc->pd updates at the end of the function.
Cc: stable@vger.kernel.org
Fixes: 37416e5549 ("clk: qcom: gdsc: Handle GDSC regulator supplies")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210721224056.3035016-1-bjorn.andersson@linaro.org
[sboyd@kernel.org: Rephrase commit text]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 25f8203b4b ]
When a Data CRC interrupt is received, the driver disables the DMA, then
sends the stop/abort command and then waits for Data Transfer Over.
However, sometimes, when a data CRC error is received in the middle of a
multi-block write transfer, the Data Transfer Over interrupt is never
received, and the driver hangs and never completes the request.
The driver sets the BMOD.SWR bit (SDMMC_IDMAC_SWRESET) when stopping the
DMA, but according to the manual CMD.STOP_ABORT_CMD should be programmed
"before assertion of SWR". Do these operations in the recommended
order. With this change the Data Transfer Over is always received
correctly in my tests.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210630102232.16011-1-vincent.whitchurch@axis.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa05bdb89b ]
This reverts commit 9ea3e52c5b.
Cited commit added a check to make sure 'action' is not NULL, but
'action' is already dereferenced before the check, when calling
flow_offload_has_one_action().
Therefore, the check does not make any sense and results in a smatch
warning:
include/net/flow_offload.h:322 flow_action_mixed_hw_stats_check() warn:
variable dereferenced before check 'action' (see line 319)
Fix by reverting this commit.
Cc: gushengxian <gushengxian@yulong.com>
Fixes: 9ea3e52c5b ("flow_offload: action should not be NULL when it is referenced")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://lore.kernel.org/r/20210819105842.1315705-1-idosch@idosch.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8da80c9d50 ]
Make changes to MAC address dependent on the response of PF.
Disallow changes to HW MAC address and MAC filter from untrusted
VF, thanks to that ping is not lost if VF tries to change MAC.
Add a new field in iavf_mac_filter, to indicate whether there
was response from PF for given filter. Based on this field pass
or discard the filter.
If untrusted VF tried to change it's address, it's not changed.
Still filter was changed, because of that ping couldn't go through.
Fixes: c5c922b3e0 ("iavf: fix MAC address setting for VFs when filter is rejected")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Gurucharan G <Gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a222be597e ]
Without this patch, ATR does not work. Receive/transmit uses queue
selection based on SW DCB hashing method.
If traffic classes are not configured for PF, then use
netdev_pick_tx function for selecting queue for packet transmission.
Instead of calling i40e_swdcb_skb_tx_hash, call netdev_pick_tx,
which ensures that packet is transmitted/received from CPU that is
running the application.
Reproduction steps:
1. Load i40e driver
2. Map each MSI interrupt of i40e port for each CPU
3. Disable ntuple, enable ATR i.e.:
ethtool -K $interface ntuple off
ethtool --set-priv-flags $interface flow-director-atr
4. Run application that is generating traffic and is bound to a
single CPU, i.e.:
taskset -c 9 netperf -H 1.1.1.1 -t TCP_RR -l 10
5. Observe behavior:
Application's traffic should be restricted to the CPU provided in
taskset.
Fixes: 89ec1f0886 ("i40e: Fix queue-to-TC mapping on Tx")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a876a33d2a ]
The register of USB_BP2_EN is 16 bits, so we should use
ocp_write_word(), not ocp_write_byte().
Fixes: 9370f2d05a ("support request_firmware for RTL8153")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8798d36411 ]
This fixes improper iotlb invalidation in intel_pasid_tear_down_entry().
When a PASID was used as nested mode, released and reused, the following
error message will appear:
[ 180.187556] Unexpected page request in Privilege Mode
[ 180.187565] Unexpected page request in Privilege Mode
[ 180.279933] Unexpected page request in Privilege Mode
[ 180.279937] Unexpected page request in Privilege Mode
Per chapter 6.5.3.3 of VT-d spec 3.3, when tear down a pasid entry, the
software should use Domain selective IOTLB flush if the PGTT of the pasid
entry is SL only or Nested, while for the pasid entries whose PGTT is FL
only or PT using PASID-based IOTLB flush is enough.
Fixes: 2cd1311a26 ("iommu/vt-d: Add set domain DOMAIN_ATTR_NESTING attr")
Signed-off-by: Kumar Sanjay K <sanjay.k.kumar@intel.com>
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Tested-by: Yi Sun <yi.y.sun@intel.com>
Link: https://lore.kernel.org/r/20210817042425.1784279-1-yi.l.liu@intel.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210817124321.1517985-3-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 01634047bf ]
fq qdisc requires tstamp to be cleared in the forwarding path. Now ovs
doesn't clear skb->tstamp. We encountered a problem with linux
version 5.4.56 and ovs version 2.14.1, and packets failed to
dequeue from qdisc when fq qdisc was attached to ovs port.
Fixes: fb420d5d91 ("tcp/fq: move back to CLOCK_MONOTONIC")
Signed-off-by: kaixi.fan <fankaixi.li@bytedance.com>
Signed-off-by: xiexiaohui <xiexiaohui.xxh@bytedance.com>
Reviewed-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7bd0cef5da ]
When registering mdiobus children, if we get an -EPROBE_DEFER, we shouldn't
ignore it and continue registering the rest of the mdiobus children. This
would permanently prevent the deferring child mdiobus from working instead
of reattempting it in the future. So, if a child mdiobus needs to be
reattempted in the future, defer the entire mdio-mux initialization.
This fixes the issue where PHYs sitting under the mdio-mux aren't
initialized correctly if the PHY's interrupt controller is not yet ready
when the mdio-mux is being probed. Additional context in the link below.
Fixes: 0ca2997d14 ("netdev/of/phy: Add MDIO bus multiplexer support.")
Link: https://lore.kernel.org/lkml/CAGETcx95kHrv8wA-O+-JtfH7H9biJEGJtijuPVN0V5dUKUAB3A@mail.gmail.com/#t
Signed-off-by: Saravana Kannan <saravanak@google.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Marc Zyngier <maz@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86b9bbd332 ]
When adding support for using the skb->hash value as the flow hash in CAKE,
I accidentally introduced a logic error that broke the host-only isolation
modes of CAKE (srchost and dsthost keywords). Specifically, the flow_hash
variable should stay initialised to 0 in cake_hash() in pure host-based
hashing mode. Add a check for this before using the skb->hash value as
flow_hash.
Fixes: b0c19ed608 ("sch_cake: Take advantage of skb->hash where appropriate")
Reported-by: Pete Heist <pete@heistp.net>
Tested-by: Pete Heist <pete@heistp.net>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dbcf24d153 ]
Commit a02e8964ea ("virtio-net: ethtool configurable LRO")
maps LRO to virtio guest offloading features and allows the
administrator to enable and disable those features via ethtool.
This leads to several issues:
- For a device that doesn't support control guest offloads, the "LRO"
can't be disabled triggering WARN in dev_disable_lro() when turning
off LRO or when enabling forwarding bridging etc.
- For a device that supports control guest offloads, the guest
offloads are disabled in cases of bridging, forwarding etc slowing
down the traffic.
Fix this by using NETIF_F_GRO_HW instead. Though the spec does not
guarantee packets to be re-segmented as the original ones,
we can add that to the spec, possibly with a flag for devices to
differentiate between GRO and LRO.
Further, we never advertised LRO historically before a02e8964ea
("virtio-net: ethtool configurable LRO") and so bridged/forwarded
configs effectively always relied on virtio receive offloads behaving
like GRO - thus even if this breaks any configs it is at least not
a regression.
Fixes: a02e8964ea ("virtio-net: ethtool configurable LRO")
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reported-by: Ivan <ivan@prestigetransportation.com>
Tested-by: Ivan <ivan@prestigetransportation.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97c2c69e19 ]
The number of queues implemented by many virtio backends is limited,
especially some machines have a large number of CPUs. In this case, it
is often impossible to allocate a separate queue for
XDP_TX/XDP_REDIRECT, then xdp cannot be loaded to work, even xdp does
not use the XDP_TX/XDP_REDIRECT.
This patch allows XDP_TX/XDP_REDIRECT to run by reuse the existing SQ
with __netif_tx_lock() hold when there are not enough queues.
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Reviewed-by: Dust Li <dust.li@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09e856d54b ]
To fix the "reverse-NAT" for replies.
When a packet is sent over a VRF, the POST_ROUTING hooks are called
twice: Once from the VRF interface, and once from the "actual"
interface the packet will be sent from:
1) First SNAT: l3mdev_l3_out() -> vrf_l3_out() -> .. -> vrf_output_direct()
This causes the POST_ROUTING hooks to run.
2) Second SNAT: 'ip_output()' calls POST_ROUTING hooks again.
Similarly for replies, first ip_rcv() calls PRE_ROUTING hooks, and
second vrf_l3_rcv() calls them again.
As an example, consider the following SNAT rule:
> iptables -t nat -A POSTROUTING -p udp -m udp --dport 53 -j SNAT --to-source 2.2.2.2 -o vrf_1
In this case sending over a VRF will create 2 conntrack entries.
The first is from the VRF interface, which performs the IP SNAT.
The second will run the SNAT, but since the "expected reply" will remain
the same, conntrack randomizes the source port of the packet:
e..g With a socket bound to 1.1.1.1:10000, sending to 3.3.3.3:53, the conntrack
rules are:
udp 17 29 src=2.2.2.2 dst=3.3.3.3 sport=10000 dport=53 packets=1 bytes=68 [UNREPLIED] src=3.3.3.3 dst=2.2.2.2 sport=53 dport=61033 packets=0 bytes=0 mark=0 use=1
udp 17 29 src=1.1.1.1 dst=3.3.3.3 sport=10000 dport=53 packets=1 bytes=68 [UNREPLIED] src=3.3.3.3 dst=2.2.2.2 sport=53 dport=10000 packets=0 bytes=0 mark=0 use=1
i.e. First SNAT IP from 1.1.1.1 --> 2.2.2.2, and second the src port is
SNAT-ed from 10000 --> 61033.
But when a reply is sent (3.3.3.3:53 -> 2.2.2.2:61033) only the later
conntrack entry is matched:
udp 17 29 src=2.2.2.2 dst=3.3.3.3 sport=10000 dport=53 packets=1 bytes=68 src=3.3.3.3 dst=2.2.2.2 sport=53 dport=61033 packets=1 bytes=49 mark=0 use=1
udp 17 28 src=1.1.1.1 dst=3.3.3.3 sport=10000 dport=53 packets=1 bytes=68 [UNREPLIED] src=3.3.3.3 dst=2.2.2.2 sport=53 dport=10000 packets=0 bytes=0 mark=0 use=1
And a "port 61033 unreachable" ICMP packet is sent back.
The issue is that when PRE_ROUTING hooks are called from vrf_l3_rcv(),
the skb already has a conntrack flow attached to it, which means
nf_conntrack_in() will not resolve the flow again.
This means only the dest port is "reverse-NATed" (61033 -> 10000) but
the dest IP remains 2.2.2.2, and since the socket is bound to 1.1.1.1 it's
not received.
This can be verified by logging the 4-tuple of the packet in '__udp4_lib_rcv()'.
The fix is then to reset the flow when skb is received on a VRF, to let
conntrack resolve the flow again (which now will hit the earlier flow).
To reproduce: (Without the fix "Got pkt_to_nat_port" will not be printed by
running 'bash ./repro'):
$ cat run_in_A1.py
import logging
logging.getLogger("scapy.runtime").setLevel(logging.ERROR)
from scapy.all import *
import argparse
def get_packet_to_send(udp_dst_port, msg_name):
return Ether(src='11:22:33:44:55:66', dst=iface_mac)/ \
IP(src='3.3.3.3', dst='2.2.2.2')/ \
UDP(sport=53, dport=udp_dst_port)/ \
Raw(f'{msg_name}\x0012345678901234567890')
parser = argparse.ArgumentParser()
parser.add_argument('-iface_mac', dest="iface_mac", type=str, required=True,
help="From run_in_A3.py")
parser.add_argument('-socket_port', dest="socket_port", type=str,
required=True, help="From run_in_A3.py")
parser.add_argument('-v1_mac', dest="v1_mac", type=str, required=True,
help="From script")
args, _ = parser.parse_known_args()
iface_mac = args.iface_mac
socket_port = int(args.socket_port)
v1_mac = args.v1_mac
print(f'Source port before NAT: {socket_port}')
while True:
pkts = sniff(iface='_v0', store=True, count=1, timeout=10)
if 0 == len(pkts):
print('Something failed, rerun the script :(', flush=True)
break
pkt = pkts[0]
if not pkt.haslayer('UDP'):
continue
pkt_sport = pkt.getlayer('UDP').sport
print(f'Source port after NAT: {pkt_sport}', flush=True)
pkt_to_send = get_packet_to_send(pkt_sport, 'pkt_to_nat_port')
sendp(pkt_to_send, '_v0', verbose=False) # Will not be received
pkt_to_send = get_packet_to_send(socket_port, 'pkt_to_socket_port')
sendp(pkt_to_send, '_v0', verbose=False)
break
$ cat run_in_A2.py
import socket
import netifaces
print(f"{netifaces.ifaddresses('e00000')[netifaces.AF_LINK][0]['addr']}",
flush=True)
s = socket.socket(socket.AF_INET, socket.SOCK_DGRAM)
s.setsockopt(socket.SOL_SOCKET, socket.SO_BINDTODEVICE,
str('vrf_1' + '\0').encode('utf-8'))
s.connect(('3.3.3.3', 53))
print(f'{s. getsockname()[1]}', flush=True)
s.settimeout(5)
while True:
try:
# Periodically send in order to keep the conntrack entry alive.
s.send(b'a'*40)
resp = s.recvfrom(1024)
msg_name = resp[0].decode('utf-8').split('\0')[0]
print(f"Got {msg_name}", flush=True)
except Exception as e:
pass
$ cat repro.sh
ip netns del A1 2> /dev/null
ip netns del A2 2> /dev/null
ip netns add A1
ip netns add A2
ip -n A1 link add _v0 type veth peer name _v1 netns A2
ip -n A1 link set _v0 up
ip -n A2 link add e00000 type bond
ip -n A2 link add lo0 type dummy
ip -n A2 link add vrf_1 type vrf table 10001
ip -n A2 link set vrf_1 up
ip -n A2 link set e00000 master vrf_1
ip -n A2 addr add 1.1.1.1/24 dev e00000
ip -n A2 link set e00000 up
ip -n A2 link set _v1 master e00000
ip -n A2 link set _v1 up
ip -n A2 link set lo0 up
ip -n A2 addr add 2.2.2.2/32 dev lo0
ip -n A2 neigh add 1.1.1.10 lladdr 77:77:77:77:77:77 dev e00000
ip -n A2 route add 3.3.3.3/32 via 1.1.1.10 dev e00000 table 10001
ip netns exec A2 iptables -t nat -A POSTROUTING -p udp -m udp --dport 53 -j \
SNAT --to-source 2.2.2.2 -o vrf_1
sleep 5
ip netns exec A2 python3 run_in_A2.py > x &
XPID=$!
sleep 5
IFACE_MAC=`sed -n 1p x`
SOCKET_PORT=`sed -n 2p x`
V1_MAC=`ip -n A2 link show _v1 | sed -n 2p | awk '{print $2'}`
ip netns exec A1 python3 run_in_A1.py -iface_mac ${IFACE_MAC} -socket_port \
${SOCKET_PORT} -v1_mac ${SOCKET_PORT}
sleep 5
kill -9 $XPID
wait $XPID 2> /dev/null
ip netns del A1
ip netns del A2
tail x -n 2
rm x
set +x
Fixes: 73e20b761a ("net: vrf: Add support for PREROUTING rules on vrf device")
Signed-off-by: Lahav Schlesinger <lschlesinger@drivenets.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20210815120002.2787653-1-lschlesinger@drivenets.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 828affc27e ]
Each completion ring entry has a valid bit to indicate that the entry
contains a valid completion event. The driver's main poll loop
__bnxt_poll_work() has the proper dma_rmb() to make sure the valid
bit of the next entry has been checked before proceeding further.
But when we call bnxt_rx_pkt() to process the RX event, the RX
completion event consists of two completion entries and only the
first entry has been checked to be valid. We need the same barrier
after checking the next completion entry. Add missing dma_rmb()
barriers in bnxt_rx_pkt() and other similar locations.
Fixes: 67a95e2022 ("bnxt_en: Need memory barrier when processing the completion ring.")
Reported-by: Lance Richardson <lance.richardson@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Reviewed-by: Lance Richardson <lance.richardson@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55c8fca1da ]
During the swap dependency on PCH_GBE to selection PTP_1588_CLOCK_PCH
incidentally dropped the implicit dependency on the PCI. Restore it.
Fixes: 18d359ceb0 ("pch_gbe, ptp_pch: Fix the dependency direction between these drivers")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19d1532a18 ]
Syzbot reported slab-out-of bounds write in decode_data().
The problem was in missing validation checks.
Syzbot's reproducer generated malicious input, which caused
decode_data() to be called a lot in sixpack_decode(). Since
rx_count_cooked is only 400 bytes and noone reported before,
that 400 bytes is not enough, let's just check if input is malicious
and complain about buffer overrun.
Fail log:
==================================================================
BUG: KASAN: slab-out-of-bounds in drivers/net/hamradio/6pack.c:843
Write of size 1 at addr ffff888087c5544e by task kworker/u4:0/7
CPU: 0 PID: 7 Comm: kworker/u4:0 Not tainted 5.6.0-rc3-syzkaller #0
...
Workqueue: events_unbound flush_to_ldisc
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x197/0x210 lib/dump_stack.c:118
print_address_description.constprop.0.cold+0xd4/0x30b mm/kasan/report.c:374
__kasan_report.cold+0x1b/0x32 mm/kasan/report.c:506
kasan_report+0x12/0x20 mm/kasan/common.c:641
__asan_report_store1_noabort+0x17/0x20 mm/kasan/generic_report.c:137
decode_data.part.0+0x23b/0x270 drivers/net/hamradio/6pack.c:843
decode_data drivers/net/hamradio/6pack.c:965 [inline]
sixpack_decode drivers/net/hamradio/6pack.c:968 [inline]
Reported-and-tested-by: syzbot+fc8cd9a673d4577fb2e4@syzkaller.appspotmail.com
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8d8c5d80f ]
skbs are freed on error and not put on the ring. We may, however,
be in a situation where we're freeing the last skb of a batch,
and there is a doorbell ring pending because of xmit_more() being
true earlier. Make sure we ring the door bell in such situations.
Since errors are rare don't pay attention to xmit_more() and just
always flush the pending frames.
The busy case should be safe to be left alone because it can
only happen if start_xmit races with completions and they
both enable the queue. In that case the kick can't be pending.
Noticed while reading the code.
Fixes: 4d172f21ce ("bnxt_en: Implement xmit_more.")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 01cca6b933 ]
napi schedules DIM, napi has to be disabled first,
then DIM canceled.
Noticed while reading the code.
Fixes: 0bc0b97fca ("bnxt_en: cleanup DIM work on device shutdown")
Fixes: 6a8788f256 ("bnxt_en: add support for software dynamic interrupt moderation")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c603136c9 ]
We can't take the tx lock from the napi poll routine, because
netpoll can poll napi at any moment, including with the tx lock
already held.
The tx lock is protecting against two paths - the disable
path, and (as Michael points out) the NETDEV_TX_BUSY case
which may occur if NAPI completions race with start_xmit
and both decide to re-enable the queue.
For the disable/ifdown path use synchronize_net() to make sure
closing the device does not race we restarting the queues.
Annotate accesses to dev_state against data races.
For the NAPI cleanup vs start_xmit path - appropriate barriers
are already in place in the main spot where Tx queue is stopped
but we need to do the same careful dance in the TX_BUSY case.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45c709f8c7 ]
"access skb fields ok" verifier test fails on s390 with the "verifier
bug. zext_dst is set, but no reg is defined" message. The first insns
of the test prog are ...
0: 61 01 00 00 00 00 00 00 ldxw %r0,[%r1+0]
8: 35 00 00 01 00 00 00 00 jge %r0,0,1
10: 61 01 00 08 00 00 00 00 ldxw %r0,[%r1+8]
... and the 3rd one is dead (this does not look intentional to me, but
this is a separate topic).
sanitize_dead_code() converts dead insns into "ja -1", but keeps
zext_dst. When opt_subreg_zext_lo32_rnd_hi32() tries to parse such
an insn, it sees this discrepancy and bails. This problem can be seen
only with JITs whose bpf_jit_needs_zext() returns true.
Fix by clearning dead insns' zext_dst.
The commits that contributed to this problem are:
1. 5aa5bd14c5 ("bpf: add initial suite for selftests"), which
introduced the test with the dead code.
2. 5327ed3d44 ("bpf: verifier: mark verified-insn with
sub-register zext flag"), which introduced the zext_dst flag.
3. 83a2881903 ("bpf: Account for BPF_FETCH in
insn_has_def32()"), which introduced the sanity check.
4. 9183671af6 ("bpf: Fix leakage under speculation on
mispredicted branches"), which bisect points to.
It's best to fix this on stable branches that contain the second one,
since that's the point where the inconsistency was introduced.
Fixes: 5327ed3d44 ("bpf: verifier: mark verified-insn with sub-register zext flag")
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210812151811.184086-2-iii@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71dcadba34 ]
The orginal setting is not correct, fix it to follow hardware data sheet.
If keep this error setting, mt8173/mt8183 display ok
but mt8192 display abnormal.
Fixes: 0664d1392c ("drm/mediatek: Add AAL engine basic function")
Signed-off-by: Yongqiang Niu <yongqiang.niu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08dbd56602 ]
The current code treats an empty iotlb provdied in set_map() as a
special case and destroy the memory region object. This must not be done
since the virtqueue objects reference this MR. Doing so will cause the
driver unload to emit errors and log timeouts caused by the firmware
complaining on busy resources.
This patch treats an empty iotlb as any other change of mapping. In this
case, mlx5_vdpa_create_mr() will fail and the entire set_map() call to
fail.
This issue has not been encountered before but was seen to occur in a
non-official version of qemu. Since qemu is a userspace program, the
driver must protect against such case.
Fixes: 94abbccdf2 ("vdpa/mlx5: Add shared memory registration code")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20210811053713.66658-1-elic@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06a089ef64 ]
We have changed the return type for sysc_check_active_timer() from -EBUSY
to -ENXIO, but the gpt12 system timer fix still checks for -EBUSY. We are
also not returning on other errors like we did earlier as noted by
Pavel Machek <pavel@denx.de>.
Commit 3ff340e24c ("bus: ti-sysc: Fix gpt12 system timer issue with
reserved status") should have been updated for commit 65fb736761
("bus: ti-sysc: suppress err msg for timers used as clockevent/source").
Let's fix the issue by checking for -ENXIO and returning on any other
errors as suggested by Pavel Machek <pavel@denx.de>.
Fixes: 3ff340e24c ("bus: ti-sysc: Fix gpt12 system timer issue with reserved status")
Depends-on: 65fb736761 ("bus: ti-sysc: suppress err msg for timers used as clockevent/source")
Reported-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Pavel Machek (CIP) <pavel@denx.de>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86aab09a48 ]
GCC complains about empty macros in an 'if' statement, so convert
them to 'do {} while (0)' macros.
Fixes these build warnings:
net/dccp/output.c: In function 'dccp_xmit_packet':
../net/dccp/output.c:283:71: warning: suggest braces around empty body in an 'if' statement [-Wempty-body]
283 | dccp_pr_debug("transmit_skb() returned err=%d\n", err);
net/dccp/ackvec.c: In function 'dccp_ackvec_update_old':
../net/dccp/ackvec.c:163:80: warning: suggest braces around empty body in an 'else' statement [-Wempty-body]
163 | (unsigned long long)seqno, state);
Fixes: dc841e30ea ("dccp: Extend CCID packet dequeueing interface")
Fixes: 3802408644 ("dccp ccid-2: Update code for the Ack Vector input/registration routine")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: dccp@vger.kernel.org
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 484f2b7c61 ]
The 1.2 GHz variant of the Armada 3720 SOC is unstable with DVFS: when
the SOC boots, the WTMI firmware sets clocks and AVS values that work
correctly with 1.2 GHz CPU frequency, but random crashes occur once
cpufreq driver starts scaling.
We do not know currently what is the reason:
- it may be that the voltage value for L0 for 1.2 GHz variant provided
by the vendor in the OTP is simply incorrect when scaling is used,
- it may be that some delay is needed somewhere,
- it may be something else.
The most sane solution now seems to be to simply forbid the cpufreq
driver on 1.2 GHz variant.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: 92ce45fb87 ("cpufreq: Add DVFS support for Armada 37xx")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5aa95d8834 ]
If probe_device is failing, iommu_group is not initialized because
iommu_group_add_device is not reached, so freeing it will result
in NULL pointer access.
iommu_bus_init
->bus_iommu_probe
->probe_iommu_group in for each:/* return -22 in fail case */
->iommu_probe_device
->__iommu_probe_device /* return -22 here.*/
-> ops->probe_device /* return -22 here.*/
-> iommu_group_get_for_dev
-> ops->device_group
-> iommu_group_add_device //good case
->remove_iommu_group //in fail case, it will remove group
->iommu_release_device
->iommu_group_remove_device // here we don't have group
In my case ops->probe_device (mtk_iommu_probe_device from
mtk_iommu_v1.c) is due to failing fwspec->ops mismatch.
Fixes: d72e31c937 ("iommu: IOMMU Groups")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://lore.kernel.org/r/20210731074737.4573-1-linux@fw-web.de
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cca342d98b ]
A different wait queue was used when removing ctrl_wait than when adding
it. This effectively made the remove operation without locking compared
to other operations on the wait queue ctrl_wait was part of. This caused
issues like below where dead000000000100 is LIST_POISON1 and
dead000000000200 is LIST_POISON2.
list_add corruption. next->prev should be prev (ffffffc1b0a33a08), \
but was dead000000000200. (next=ffffffc03ac77de0).
------------[ cut here ]------------
CPU: 3 PID: 2138 Comm: bluetoothd Tainted: G O 4.4.238+ #9
...
---[ end trace 0adc2158f0646eac ]---
Call trace:
[<ffffffc000443f78>] __list_add+0x38/0xb0
[<ffffffc0000f0d04>] add_wait_queue+0x4c/0x68
[<ffffffc00020eecc>] __pollwait+0xec/0x100
[<ffffffc000d1556c>] bt_sock_poll+0x74/0x200
[<ffffffc000bdb8a8>] sock_poll+0x110/0x128
[<ffffffc000210378>] do_sys_poll+0x220/0x480
[<ffffffc0002106f0>] SyS_poll+0x80/0x138
[<ffffffc00008510c>] __sys_trace_return+0x0/0x4
Unable to handle kernel paging request at virtual address dead000000000100
...
CPU: 4 PID: 5387 Comm: kworker/u15:3 Tainted: G W O 4.4.238+ #9
...
Call trace:
[<ffffffc0000f079c>] __wake_up_common+0x7c/0xa8
[<ffffffc0000f0818>] __wake_up+0x50/0x70
[<ffffffc000be11b0>] sock_def_wakeup+0x58/0x60
[<ffffffc000de5e10>] l2cap_sock_teardown_cb+0x200/0x224
[<ffffffc000d3f2ac>] l2cap_chan_del+0xa4/0x298
[<ffffffc000d45ea0>] l2cap_conn_del+0x118/0x198
[<ffffffc000d45f8c>] l2cap_disconn_cfm+0x6c/0x78
[<ffffffc000d29934>] hci_event_packet+0x564/0x2e30
[<ffffffc000d19b0c>] hci_rx_work+0x10c/0x360
[<ffffffc0000c2218>] process_one_work+0x268/0x460
[<ffffffc0000c2678>] worker_thread+0x268/0x480
[<ffffffc0000c94e0>] kthread+0x118/0x128
[<ffffffc000085070>] ret_from_fork+0x10/0x20
---[ end trace 0adc2158f0646ead ]---
Signed-off-by: Ole Bjørn Midtbø <omidtbo@cisco.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4152b297d ]
[Why]
HPD disable and enable sequences are not mutually exclusive
on Linux. For HPDs that spans over 1s (i.e. HPD low = 1s),
part of the disable sequence (specifically, a request to SMU
to lower refclk) could come right before the call to PHY
enable, causing DMUB to access an unresponsive PHY
and thus a hard hang on the system.
[How]
Disable 48mhz refclk off on native DP.
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06050a0f01 ]
Why:
In DCN2x, HW doesn't automatically divide MASTER_UPDATE_LOCK_DB_X
by the number of pipes ODM Combined.
How:
Set MASTER_UPDATE_LOCK_DB_X to the value that is adjusted by the
number of pipes ODM Combined.
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Bing Guo <bing.guo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b67d4d63e ]
Currently phy_device state could be left in inconsistent state shown
by following alert message[1]. This is because phy_read_status could
be called concurrently from lan78xx_delayedwork, phy_state_machine and
__ethtool_get_link. Fix this by making sure that phy_device state is
updated atomically.
[1] lan78xx 1-1.1.1:1.0 eth0: No phy led trigger registered for speed(-1)
Signed-off-by: Ivan T. Ivanov <iivanov@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a160e2e9a ]
Certain call sites of get_geristers() did not do proper error handling. This
could be a problem as get_geristers() typically return the data via pointer to a
buffer. If an error occurred the code is carelessly manipulating the wrong data.
Signed-off-by: Petko Manolov <petkan@nucleusys.com>
Reviewed-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1159e25c13 ]
A crash has been observed if rmmod is done while automatic debug
collection in progress. It is due to a race condition between
both of them.
To fix stop the sp_task during unload to avoid running qede_sp_task
even if they are schedule during removal process.
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f0f82e2476 ]
After adding physical volumes to a volume group through vgextend, the
kernel will rescan the partitions. This in turn will cause the device
capacity to be queried.
If the device status is set to offline through sysfs at this time, READ
CAPACITY command will return a result which the host byte is
DID_NO_CONNECT, and the capacity of the device will be set to zero in
read_capacity_error(). After setting device status back to running, the
capacity of the device will remain stuck at zero.
Fix this issue by rescanning device when the device state changes to
SDEV_RUNNING.
Link: https://lore.kernel.org/r/20210727034455.1494960-1-lijinlin3@huawei.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: lijinlin <lijinlin3@huawei.com>
Signed-off-by: Wu Bo <wubo40@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 70edd2e6f6 ]
Avoid printing a 'target allocation failed' error if the driver
target_alloc() callback function returns -ENXIO. This return value
indicates that the corresponding H:C:T:L entry is empty.
Removing this error reduces the scan time if the user issues SCAN_WILD_CARD
scan operation through sysfs parameter on a host with a lot of empty
H:C:T:L entries.
Avoiding the printk on -ENXIO matches the behavior of the other callback
functions during scanning.
Link: https://lore.kernel.org/r/20210726115402.1936-1-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eda97cb095 ]
If the router_xlate can not find the controller in the available DMA
devices then it should return with -EPORBE_DEFER in a same way as the
of_dma_request_slave_channel() does.
The issue can be reproduced if the event router is registered before the
DMA controller itself and a driver would request for a channel before the
controller is registered.
In of_dma_request_slave_channel():
1. of_dma_find_controller() would find the dma_router
2. ofdma->of_dma_xlate() would fail and returned NULL
3. -ENODEV is returned as error code
with this patch we would return in this case the correct -EPROBE_DEFER and
the client can try to request the channel later.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20210717190021.21897-1-peter.ujfalusi@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20a6b3fd8e ]
Based on the latest timing specifications for the TPS65218 from the data
sheet, http://www.ti.com/lit/ds/symlink/tps65218.pdf, document SLDS206
from November 2014, we must change the i2c bus speed to better fit within
the minimum high SCL time required for proper i2c transfer.
When running at 400khz, measurements show that SCL spends
0.8125 uS/1.666 uS high/low which violates the requirement for minimum
high period of SCL provided in datasheet Table 7.6 which is 1 uS.
Switching to 100khz gives us 5 uS/5 uS high/low which both fall above
the minimum given values for 100 khz, 4.0 uS/4.7 uS high/low.
Without this patch occasionally a voltage set operation from the kernel
will appear to have worked but the actual voltage reflected on the PMIC
will not have updated, causing problems especially with cpufreq that may
update to a higher OPP without actually raising the voltage on DCDC2,
leading to a hang.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7dd2dd4ff9 ]
When user calls dmaengine_terminate_sync, the driver will clean up any
remaining descriptors for all the pending or active transfers that had
previously been submitted. However, this might happen whilst the tasklet is
invoking the DMA callback for the last finished transfer, so by the time it
returns and takes over the channel's spinlock, the list of completed
descriptors it was traversing is no longer valid. This leads to a
read-after-free situation.
Fix it by signalling whether a user-triggered termination has happened by
means of a boolean variable.
Signed-off-by: Adrian Larumbe <adrian.martinezlarumbe@imgtec.com>
Link: https://lore.kernel.org/r/20210706234338.7696-3-adrian.martinezlarumbe@imgtec.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0863f1927 ]
When the user submits a control URB via usbfs, the user supplies the
bRequestType value and the kernel uses it to compute the pipe value.
However, do_proc_control() performs this computation incorrectly in
the case where the bRequestType direction bit is set to USB_DIR_IN and
the URB's transfer length is 0: The pipe's direction is also set to IN
but it should be OUT, which is the direction the actual transfer will
use regardless of bRequestType.
Commit 5cc59c418f ("USB: core: WARN if pipe direction != setup
packet direction") added a check to compare the direction bit in the
pipe value to a control URB's actual direction and to WARN if they are
different. This can be triggered by the incorrect computation
mentioned above, as found by syzbot.
This patch fixes the computation, thus avoiding the WARNing.
Reported-and-tested-by: syzbot+72af3105289dcb4c055b@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20210712185436.GB326369@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da6393cdd8 ]
Reported by syzkaller:
WARNING: CPU: 7 PID: 10526 at linux/arch/x86/kvm//x86.c:7621 x86_emulate_instruction+0x41b/0x510 [kvm]
RIP: 0010:x86_emulate_instruction+0x41b/0x510 [kvm]
Call Trace:
kvm_mmu_page_fault+0x126/0x8f0 [kvm]
vmx_handle_exit+0x11e/0x680 [kvm_intel]
vcpu_enter_guest+0xd95/0x1b40 [kvm]
kvm_arch_vcpu_ioctl_run+0x377/0x6a0 [kvm]
kvm_vcpu_ioctl+0x389/0x630 [kvm]
__x64_sys_ioctl+0x8e/0xd0
do_syscall_64+0x3c/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
Commit 4a1e10d5b5 ("KVM: x86: handle hardware breakpoints during emulation())
adds hardware breakpoints check before emulation the instruction and parts of
emulation context initialization, actually we don't have the EMULTYPE_NO_DECODE flag
here and the emulation context will not be reused. Commit c8848cee74 ("KVM: x86:
set ctxt->have_exception in x86_decode_insn()) triggers the warning because it
catches the stale emulation context has #UD, however, it is not during instruction
decoding which should result in EMULATION_FAILED. This patch fixes it by moving
the second part emulation context initialization into init_emulate_ctxt() and
before hardware breakpoints check. The ctxt->ud will be dropped by a follow-up
patch.
syzkaller source: https://syzkaller.appspot.com/x/repro.c?x=134683fdd00000
Reported-by: syzbot+71271244f206d17f6441@syzkaller.appspotmail.com
Fixes: 4a1e10d5b5 (KVM: x86: handle hardware breakpoints during emulation)
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Message-Id: <1622160097-37633-1-git-send-email-wanpengli@tencent.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4aa2691dcb ]
Move the instruction decode part out of x86_emulate_instruction() for it
to be used in other places. Also kvm_clear_exception_queue() is moved
inside the if-statement as it doesn't apply when KVM are coming back from
userspace.
Co-developed-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Wei Huang <wei.huang2@amd.com>
Message-Id: <20210126081831.570253-2-wei.huang2@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea354b6ddd ]
Syzbot discovered that the probe error handling doesn't clean up the
resources allocated in zr364xx_board_init(). There are several
related bugs in this code so I have re-written the error handling.
1) Introduce a new function zr364xx_board_uninit() which cleans up
the resources in zr364xx_board_init().
2) In zr364xx_board_init() if the call to zr364xx_start_readpipe()
fails then release the "cam->buffer.frame[i].lpvbits" memory
before returning. This way every function either allocates
everything successfully or it cleans up after itself.
3) Re-write the probe function so that each failure path goto frees
the most recent allocation. That way we don't free anything
before it has been allocated and we can also verify that
everything is freed.
4) Originally, in the probe function the "cam->v4l2_dev.release"
pointer was set to "zr364xx_release" near the start but I moved
that assignment to the end, after everything had succeeded. The
release function was never actually called during the probe cleanup
process, but with this change I wanted to make it clear that we
don't want to call zr364xx_release() until everything is
allocated successfully.
Next I re-wrote the zr364xx_release() function. Ideally this would
have been a simple matter of copy and pasting the cleanup code from
probe and adding an additional call to video_unregister_device(). But
there are a couple quirks to note.
1) The probe function does not call videobuf_mmap_free() and I don't
know where the videobuf_mmap is allocated. I left the code as-is to
avoid introducing a bug in code I don't understand.
2) The zr364xx_board_uninit() has a call to zr364xx_stop_readpipe()
which is a change from the original behavior with regards to
unloading the driver. Calling zr364xx_stop_readpipe() on a stopped
pipe is not a problem so this is safe and is potentially a bugfix.
Reported-by: syzbot+b4d54814b339b5c6bbd4@syzkaller.appspotmail.com
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af0321a5be ]
zr364xx_start_readpipe() can fail but callers do not care about that.
This can result in various negative consequences. The patch adds missed
error handling.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ca2848022c upstream.
Do not delete a key cache entry that is still being referenced by
pending frames in TXQs. This avoids reuse of the key cache entry while a
frame might still be transmitted using it.
To avoid having to do any additional operations during the main TX path
operations, track pending key cache entries in a new bitmap and check
whether any pending entries can be deleted before every new key
add/remove operation. Also clear any remaining entries when stopping the
interface.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201214172118.18100-6-jouni@codeaurora.org
Cc: Pali Rohár <pali@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56c5485c9e upstream.
It is possible for there to be pending frames in TXQs with a reference
to the key cache entry that is being deleted. If such a key cache entry
is cleared, those pending frame in TXQ might get transmitted without
proper encryption. It is safer to leave the previously used key into the
key cache in such cases. Instead, only clear the MAC address to prevent
RX processing from using this key cache entry.
This is needed in particularly in AP mode where the TXQs cannot be
flushed on station disconnection. This change alone may not be able to
address all cases where the key cache entry might get reused for other
purposes immediately (the key cache entry should be released for reuse
only once the TXQs do not have any remaining references to them), but
this makes it less likely to get unprotected frames and the more
complete changes may end up being significantly more complex.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201214172118.18100-2-jouni@codeaurora.org
Cc: Pali Rohár <pali@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the firmware doesn't setup the HSM rate (such as when booting
without an HDMI cable plugged in), its rate is 0 and thus any register
access results in a CPU stall, even though HSM is enabled.
Let's enforce a minimum rate at boot to avoid this issue.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Commit 9d44abbbb8 ("drm/vc4: Fall back to using an EDID probe in the
absence of a GPIO.") added some code to read the EDID through DDC in the
HDMI driver detect hook since the Pi3 had no HPD GPIO back then.
However, commit b1b8f45b31 ("ARM: dts: bcm2837: Add missing GPIOs of
Expander") changed that a couple of years later.
This causes an issue though since some TV (like the LG 55C8) when it
comes out of standy will deassert the HPD line, but the EDID will
remain readable.
It causes an issues nn platforms without an HPD GPIO, like the Pi4,
where the DDC probing will be our primary mean to detect a display, and
thus we will never detect the HPD pulse. This was fine before since the
pulse was small enough that we would never detect it, and we also didn't
have anything (like the scrambler) that needed to be set up in the
display.
However, now that we have both, the display during the HPD pulse will
clear its scrambler status, and since we won't detect the
disconnect/reconnect cycle we will never enable the scrambler back.
As our main reason for that DDC probing is gone, let's just remove it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The drm_helper_hpd_irq_event() documentation states that this function
is "useful for drivers which can't or don't track hotplug interrupts for
each connector." and that "Drivers which support hotplug interrupts for
each connector individually and which have a more fine-grained detect
logic should bypass this code and directly call
drm_kms_helper_hotplug_event()". This is thus what we ended-up doing.
However, what this actually means, and is further explained in the
drm_kms_helper_hotplug_event() documentation, is that
drm_kms_helper_hotplug_event() should be called by drivers that can
track the connection status change, and if it has changed we should call
that function.
This underlying expectation we failed to provide is that the caller of
drm_kms_helper_hotplug_event() should call drm_helper_probe_detect() to
probe the new status of the connector.
Since we didn't do it, it meant that even though we were sending the
notification to user-space and the DRM clients that something changed we
never probed or updated our internal connector status ourselves.
This went mostly unnoticed since the detect callback usually doesn't
have any side-effect. Also, if we were using the DRM fbdev emulation
(which is a DRM client), or any user-space application that can deal
with hotplug events, chances are they would react to the hotplug event
by probing the connector status eventually.
However, now that we have to enable the scrambler in detect() if it was
enabled it has a side effect, and an application such as Kodi or
modetest doesn't deal with hotplug events. This resulted with a black
screen when Kodi or modetest was running when a screen was disconnected
and then reconnected, or switched off and on.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The drm_helper_hpd_irq_event() function is iterating over all the
connectors when an hotplug event is detected.
During that iteration, it will call each connector detect function and
figure out if its status changed.
Finally, if any connector changed, it will notify the user-space and the
clients that something changed on the DRM device.
This is supposed to be used for drivers that don't have a hotplug
interrupt for individual connectors. However, drivers that can use an
interrupt for a single connector are left in the dust and can either
reimplement the logic used during the iteration for each connector or
use that helper and iterate over all connectors all the time.
Since both are suboptimal, let's create a helper that will only perform
the status detection on a single connector.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The PoE HAT cooling levels are not well suited for the PoE+ HAT - the
fan fails to come on until the temperature reaches the third trip point
(50C).
Give the rpi-poe-plus overlay a different set of cooling levels -
0 32 64 128 255, as suggested by @chris-kai-in.
See: https://github.com/raspberrypi/firmware/issues/1607
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
commit 9130c2d30c upstream.
On the CPU port, we can support both tagged and untagged VLANs at the
same time by doing any necessary untagging in software rather than
hardware. To enable that, keep the CPU port's Remove Tag flag cleared
and set the dsa_switch::untag_bridge_pvid flag.
Fixes: e66f840c08 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver")
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backport to 5.10: adjust context]
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af01754f9e upstream.
When a VLAN is deleted from a port, the flags in struct
switchdev_obj_port_vlan are always 0. ksz8_port_vlan_del() copies the
BRIDGE_VLAN_INFO_UNTAGGED flag to the port's Tag Removal flag, and
therefore always clears it.
In case there are multiple VLANs configured as untagged on this port -
which seems useless, but is allowed - deleting one of them changes the
remaining VLANs to be tagged.
It's only ever necessary to change this flag when a VLAN is added to
the port, so leave it unchanged in ksz8_port_vlan_del().
Fixes: e66f840c08 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver")
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backport to 5.10: adjust context]
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f4f58f88f upstream.
The switches supported by ksz8795 only have a per-port flag for Tag
Removal. This means it is not possible to support both tagged and
untagged VLANs on the same port. Reject attempts to add a VLAN that
requires the flag to be changed, unless there are no VLANs currently
configured.
VID 0 is excluded from this check since it is untagged regardless of
the state of the flag.
On the CPU port we could support tagged and untagged VLANs at the same
time. This will be enabled by a later patch.
Fixes: e66f840c08 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver")
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backport to 5.10:
- This configuration has to be detected and rejected in the
port_vlan_prepare operation
- ksz8795_port_vlan_add() has to check again to decide whether to
change the Tag Removal flag, so put the common condition in a
separate function
- Handle VID ranges]
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef3b02a1d7 upstream.
ksz8795 has never actually enabled PVID tag insertion, and it also
programmed the PVID incorrectly. To fix this:
* Allow tag insertion to be controlled per ingress port. On most
chips, set bit 2 in Global Control 19. On KSZ88x3 this control
flag doesn't exist.
* When adding a PVID:
- Set the appropriate register bits to enable tag insertion on
egress at every other port if this was the packet's ingress port.
- Mask *out* the VID from the default tag, before or-ing in the new
PVID.
* When removing a PVID:
- Clear the same control bits to disable tag insertion.
- Don't update the default tag. This wasn't doing anything useful.
Fixes: e66f840c08 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver")
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backport to 5.10:
- Drop the KSZ88x3 cases as those chips are not supported here
- Handle VID ranges in ksz8795_port_vlan_del()]
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ksz8795 and ksz9477 drivers differ in the way they count ports.
For ksz8795, ksz_device::port_cnt does not include the host port
whereas for ksz9477 it does. This inconsistency was fixed in Linux
5.11 by a series of changes, but remains in 5.10-stable.
When probing, the common code treats a port device node with an
address >= dev->port_cnt as a fatal error. As a minimal fix, change
it to compare again dev->mib_port_cnt. This is the length of the
dev->ports array that the port number will be used to index, and
always includes the host port.
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c7dfa40099 upstream.
If L1 disables VMLOAD/VMSAVE intercepts, and doesn't enable
Virtual VMLOAD/VMSAVE (currently not supported for the nested hypervisor),
then VMLOAD/VMSAVE must operate on the L1 physical memory, which is only
possible by making L0 intercept these instructions.
Failure to do so allowed the nested guest to run VMLOAD/VMSAVE unintercepted,
and thus read/write portions of the host physical memory.
Fixes: 89c8a4984f ("KVM: SVM: Enable Virtual VMLOAD VMSAVE feature")
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f923e0712 upstream.
* Invert the mask of bits that we pick from L2 in
nested_vmcb02_prepare_control
* Invert and explicitly use VIRQ related bits bitmask in svm_clear_vintr
This fixes a security issue that allowed a malicious L1 to run L2 with
AVIC enabled, which allowed the L2 to exploit the uninitialized and enabled
AVIC to read/write the host physical memory at some offsets.
Fixes: 3d6368ef58 ("KVM: SVM: Add VMRUN handler")
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 848378812e upstream.
A recent change in LLVM causes module_{c,d}tor sections to appear when
CONFIG_K{A,C}SAN are enabled, which results in orphan section warnings
because these are not handled anywhere:
ld.lld: warning: arch/x86/pci/built-in.a(legacy.o):(.text.asan.module_ctor) is being placed in '.text.asan.module_ctor'
ld.lld: warning: arch/x86/pci/built-in.a(legacy.o):(.text.asan.module_dtor) is being placed in '.text.asan.module_dtor'
ld.lld: warning: arch/x86/pci/built-in.a(legacy.o):(.text.tsan.module_ctor) is being placed in '.text.tsan.module_ctor'
Fangrui explains: "the function asan.module_ctor has the SHF_GNU_RETAIN
flag, so it is in a separate section even with -fno-function-sections
(default)".
Place them in the TEXT_TEXT section so that these technologies continue
to work with the newer compiler versions. All of the KASAN and KCSAN
KUnit tests continue to pass after this change.
Cc: stable@vger.kernel.org
Link: https://github.com/ClangBuiltLinux/linux/issues/1432
Link: 7b78956224
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Fangrui Song <maskray@google.com>
Acked-by: Marco Elver <elver@google.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210731023107.1932981-1-nathan@kernel.org
[nc: Resolve conflict due to lack of cf68fffb66]
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8434ffe71c upstream.
There is a race in ceph_put_snap_realm. The change to the nref and the
spinlock acquisition are not done atomically, so you could decrement
nref, and before you take the spinlock, the nref is incremented again.
At that point, you end up putting it on the empty list when it
shouldn't be there. Eventually __cleanup_empty_realms runs and frees
it when it's still in-use.
Fix this by protecting the 1->0 transition with atomic_dec_and_lock,
and just drop the spinlock if we can get the rwsem.
Because these objects can also undergo a 0->1 refcount transition, we
must protect that change as well with the spinlock. Increment locklessly
unless the value is at 0, in which case we take the spinlock, increment
and then take it off the empty list if it did the 0->1 transition.
With these changes, I'm removing the dout() messages from these
functions, as well as in __put_snap_realm. They've always been racy, and
it's better to not print values that may be misleading.
Cc: stable@vger.kernel.org
URL: https://tracker.ceph.com/issues/46419
Reported-by: Mark Nelson <mnelson@redhat.com>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Luis Henriques <lhenriques@suse.de>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df2c0cb7f8 upstream.
They both say that the snap_rwsem must be held for write, but I don't
see any real reason for it, and it's not currently always called that
way.
The lookup is just walking the rbtree, so holding it for read should be
fine there. The "get" is bumping the refcount and (possibly) removing
it from the empty list. I see no need to hold the snap_rwsem for write
for that.
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52dfd86aa5 upstream.
Opening a new file is done in 2 steps on regular filesystems:
1. Call the create inode-op on the parent-dir to create an inode
to hold the meta-data related to the file.
2. Call the open file-op to get a handle for the file.
vboxsf however does not really use disk-backed inodes because it
is based on passing through file-related system-calls through to
the hypervisor. So both steps translate to an open(2) call being
passed through to the hypervisor. With the handle returned by
the first call immediately being closed again.
Making 2 open calls for a single open(..., O_CREATE, ...) calls
has 2 problems:
a) It is not really efficient.
b) It actually breaks some apps.
An example of b) is doing a git clone inside a vboxsf mount.
When git clone tries to create a tempfile to store the pak
files which is downloading the following happens:
1. vboxsf_dir_mkfile() gets called with a mode of 0444 and succeeds.
2. vboxsf_file_open() gets called with file->f_flags containing
O_RDWR. When the host is a Linux machine this fails because doing
a open(..., O_RDWR) on a file which exists and has mode 0444 results
in an -EPERM error.
Other network-filesystems and fuse avoid the problem of needing to
pass 2 open() calls to the other side by using the atomic_open
directory-inode op.
This commit fixes git clone not working inside a vboxsf mount,
by adding support for the atomic_open directory-inode op.
As an added bonus this should also make opening new files faster.
The atomic_open implementation is modelled after the atomic_open
implementations from the 9p and fuse code.
Fixes: 0fd1695766 ("fs: Add VirtualBox guest shared folder (vboxsf) support")
Reported-by: Ludovic Pouzenc <bugreports@pouzenc.fr>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 02f840f907 upstream.
Factor out the code to create / release a struct vboxsf_handle into
2 new helper functions.
This is a preparation patch for adding atomic_open support.
Fixes: 0fd1695766 ("fs: Add VirtualBox guest shared folder (vboxsf) support")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 18712c1370 upstream.
Use vmx_need_pf_intercept() when determining if L0 wants to handle a #PF
in L2 or if the VM-Exit should be forwarded to L1. The current logic fails
to account for the case where #PF is intercepted to handle
guest.MAXPHYADDR < host.MAXPHYADDR and ends up reflecting all #PFs into
L1. At best, L1 will complain and inject the #PF back into L2. At
worst, L1 will eat the unexpected fault and cause L2 to hang on infinite
page faults.
Note, while the bug was technically introduced by the commit that added
support for the MAXPHYADDR madness, the shame is all on commit
a0c134347b ("KVM: VMX: introduce vmx_need_pf_intercept").
Fixes: 1dbf5d68af ("KVM: VMX: Add guest physical address check in EPT violation and misconfig")
Cc: stable@vger.kernel.org
Cc: Peter Shier <pshier@google.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Jim Mattson <jmattson@google.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210812045615.3167686-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b9cae027b upstream.
Use the secondary_exec_controls_get() accessor in vmx_has_waitpkg() to
effectively get the controls for the current VMCS, as opposed to using
vmx->secondary_exec_controls, which is the cached value of KVM's desired
controls for vmcs01 and truly not reflective of any particular VMCS.
While the waitpkg control is not dynamic, i.e. vmcs01 will always hold
the same waitpkg configuration as vmx->secondary_exec_controls, the same
does not hold true for vmcs02 if the L1 VMM hides the feature from L2.
If L1 hides the feature _and_ does not intercept MSR_IA32_UMWAIT_CONTROL,
L2 could incorrectly read/write L1's virtual MSR instead of taking a #GP.
Fixes: 6e3ba4abce ("KVM: vmx: Emulate MSR IA32_UMWAIT_CONTROL")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210810171952.2758100-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c32ac11da3 upstream.
On arm64, the stub only moves the kernel image around in memory if
needed, which is typically only for KASLR, given that relocatable
kernels (which is the default) can run from any 64k aligned address,
which is also the minimum alignment communicated to EFI via the PE/COFF
header.
Unfortunately, some loaders appear to ignore this header, and load the
kernel at some arbitrary offset in memory. We can deal with this, but
let's check for this condition anyway, so non-compliant code can be
spotted and fixed.
Cc: <stable@vger.kernel.org> # v5.10+
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77e89afc25 upstream.
Multi-MSI uses a single MSI descriptor and there is a single mask register
when the device supports per vector masking. To avoid reading back the mask
register the value is cached in the MSI descriptor and updates are done by
clearing and setting bits in the cache and writing it to the device.
But nothing protects msi_desc::masked and the mask register from being
modified concurrently on two different CPUs for two different Linux
interrupts which belong to the same multi-MSI descriptor.
Add a lock to struct device and protect any operation on the mask and the
mask register with it.
This makes the update of msi_desc::masked unconditional, but there is no
place which requires a modification of the hardware register without
updating the masked cache.
msi_mask_irq() is now an empty wrapper which will be cleaned up in follow
up changes.
The problem goes way back to the initial support of multi-MSI, but picking
the commit which introduced the mask cache is a valid cut off point
(2.6.30).
Fixes: f2440d9acb ("PCI MSI: Refactor interrupt masking code")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.726833414@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 361fd37397 upstream.
msi_mask_irq() takes a mask and a flags argument. The mask argument is used
to mask out bits from the cached mask and the flags argument to set bits.
Some places invoke it with a flags argument which sets bits which are not
used by the device, i.e. when the device supports up to 8 vectors a full
unmask in some places sets the mask to 0xFFFFFF00. While devices probably
do not care, it's still bad practice.
Fixes: 7ba1930db0 ("PCI MSI: Unmask MSI if setup failed")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.568173099@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b9255a7cb5 upstream.
Nothing enforces the posted writes to be visible when the function
returns. Flush them even if the flush might be redundant when the entry is
masked already as the unmask will flush as well. This is either setup or a
rare affinity change event so the extra flush is not the end of the world.
While this is more a theoretical issue especially the logic in the X86
specific msi_set_affinity() function relies on the assumption that the
update has reached the hardware when the function returns.
Again, as this never has been enforced the Fixes tag refers to a commit in:
git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
Fixes: f036d4ea5fa7 ("[PATCH] ia32 Message Signalled Interrupt support")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.515188147@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da181dc974 upstream.
The specification (PCIe r5.0, sec 6.1.4.5) states:
For MSI-X, a function is permitted to cache Address and Data values
from unmasked MSI-X Table entries. However, anytime software unmasks a
currently masked MSI-X Table entry either by clearing its Mask bit or
by clearing the Function Mask bit, the function must update any Address
or Data values that it cached from that entry. If software changes the
Address or Data value of an entry while the entry is unmasked, the
result is undefined.
The Linux kernel's MSI-X support never enforced that the entry is masked
before the entry is modified hence the Fixes tag refers to a commit in:
git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
Enforce the entry to be masked across the update.
There is no point in enforcing this to be handled at all possible call
sites as this is just pointless code duplication and the common update
function is the obvious place to enforce this.
Fixes: f036d4ea5fa7 ("[PATCH] ia32 Message Signalled Interrupt support")
Reported-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.462096385@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d5ec3d361 upstream.
When MSI-X is enabled the ordering of calls is:
msix_map_region();
msix_setup_entries();
pci_msi_setup_msi_irqs();
msix_program_entries();
This has a few interesting issues:
1) msix_setup_entries() allocates the MSI descriptors and initializes them
except for the msi_desc:masked member which is left zero initialized.
2) pci_msi_setup_msi_irqs() allocates the interrupt descriptors and sets
up the MSI interrupts which ends up in pci_write_msi_msg() unless the
interrupt chip provides its own irq_write_msi_msg() function.
3) msix_program_entries() does not do what the name suggests. It solely
updates the entries array (if not NULL) and initializes the masked
member for each MSI descriptor by reading the hardware state and then
masks the entry.
Obviously this has some issues:
1) The uninitialized masked member of msi_desc prevents the enforcement
of masking the entry in pci_write_msi_msg() depending on the cached
masked bit. Aside of that half initialized data is a NONO in general
2) msix_program_entries() only ensures that the actually allocated entries
are masked. This is wrong as experimentation with crash testing and
crash kernel kexec has shown.
This limited testing unearthed that when the production kernel had more
entries in use and unmasked when it crashed and the crash kernel
allocated a smaller amount of entries, then a full scan of all entries
found unmasked entries which were in use in the production kernel.
This is obviously a device or emulation issue as the device reset
should mask all MSI-X table entries, but obviously that's just part
of the paper specification.
Cure this by:
1) Masking all table entries in hardware
2) Initializing msi_desc::masked in msix_setup_entries()
3) Removing the mask dance in msix_program_entries()
4) Renaming msix_program_entries() to msix_update_entries() to
reflect the purpose of that function.
As the masking of unused entries has never been done the Fixes tag refers
to a commit in:
git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
Fixes: f036d4ea5fa7 ("[PATCH] ia32 Message Signalled Interrupt support")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.403833459@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 438553958b upstream.
The ordering of MSI-X enable in hardware is dysfunctional:
1) MSI-X is disabled in the control register
2) Various setup functions
3) pci_msi_setup_msi_irqs() is invoked which ends up accessing
the MSI-X table entries
4) MSI-X is enabled and masked in the control register with the
comment that enabling is required for some hardware to access
the MSI-X table
Step #4 obviously contradicts #3. The history of this is an issue with the
NIU hardware. When #4 was introduced the table access actually happened in
msix_program_entries() which was invoked after enabling and masking MSI-X.
This was changed in commit d71d6432e1 ("PCI/MSI: Kill redundant call of
irq_set_msi_desc() for MSI-X interrupts") which removed the table write
from msix_program_entries().
Interestingly enough nobody noticed and either NIU still works or it did
not get any testing with a kernel 3.19 or later.
Nevertheless this is inconsistent and there is no reason why MSI-X can't be
enabled and masked in the control register early on, i.e. move step #4
above to step #1. This preserves the NIU workaround and has no side effects
on other hardware.
Fixes: d71d6432e1 ("PCI/MSI: Kill redundant call of irq_set_msi_desc() for MSI-X interrupts")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Ashok Raj <ashok.raj@intel.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.344136412@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dbbc93576e upstream.
msi_domain_alloc_irqs() invokes irq_domain_activate_irq(), but
msi_domain_free_irqs() does not enforce deactivation before tearing down
the interrupts.
This happens when PCI/MSI interrupts are set up and never used before being
torn down again, e.g. in error handling pathes. The only place which cleans
that up is the error handling path in msi_domain_alloc_irqs().
Move the cleanup from msi_domain_alloc_irqs() into msi_domain_free_irqs()
to cure that.
Fixes: f3b0946d62 ("genirq/msi: Make sure PCI MSIs are activated early")
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210518033117.78104-1-cuibixuan@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 064855a690 upstream.
Creating a new sub monitoring group in the root /sys/fs/resctrl leads to
getting the "Unavailable" value for mbm_total_bytes and mbm_local_bytes
on the entire filesystem.
Steps to reproduce:
1. mount -t resctrl resctrl /sys/fs/resctrl/
2. cd /sys/fs/resctrl/
3. cat mon_data/mon_L3_00/mbm_total_bytes
23189832
4. Create sub monitor group:
mkdir mon_groups/test1
5. cat mon_data/mon_L3_00/mbm_total_bytes
Unavailable
When a new monitoring group is created, a new RMID is assigned to the
new group. But the RMID is not active yet. When the events are read on
the new RMID, it is expected to report the status as "Unavailable".
When the user reads the events on the default monitoring group with
multiple subgroups, the events on all subgroups are consolidated
together. Currently, if any of the RMID reads report as "Unavailable",
then everything will be reported as "Unavailable".
Fix the issue by discarding the "Unavailable" reads and reporting all
the successful RMID reads. This is not a problem on Intel systems as
Intel reports 0 on Inactive RMIDs.
Fixes: d89b737901 ("x86/intel_rdt/cqm: Add mon_data")
Reported-by: Paweł Szulik <pawel.szulik@intel.com>
Signed-off-by: Babu Moger <Babu.Moger@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: stable@vger.kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=213311
Link: https://lkml.kernel.org/r/162793309296.9224.15871659871696482080.stgit@bmoger-ubuntu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c0e37dc11 upstream.
The IO/APIC cannot handle interrupt affinity changes safely after startup
other than from an interrupt handler. The startup sequence in the generic
interrupt code violates that assumption.
Mark the irq chip with the new IRQCHIP_AFFINITY_PRE_STARTUP flag so that
the default interrupt setting happens before the interrupt is started up
for the first time.
Fixes: 1840475676 ("genirq: Expose default irq affinity mask (take 3)")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.832143400@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff363f480e upstream.
The X86 MSI mechanism cannot handle interrupt affinity changes safely after
startup other than from an interrupt handler, unless interrupt remapping is
enabled. The startup sequence in the generic interrupt code violates that
assumption.
Mark the irq chips with the new IRQCHIP_AFFINITY_PRE_STARTUP flag so that
the default interrupt setting happens before the interrupt is started up
for the first time.
While the interrupt remapping MSI chip does not require this, there is no
point in treating it differently as this might spare an interrupt to a CPU
which is not in the default affinity mask.
For the non-remapping case go to the direct write path when the interrupt
is not yet started similar to the not yet activated case.
Fixes: 1840475676 ("genirq: Expose default irq affinity mask (take 3)")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.886722080@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 826da77129 upstream.
X86 IO/APIC and MSI interrupts (when used without interrupts remapping)
require that the affinity setup on startup is done before the interrupt is
enabled for the first time as the non-remapped operation mode cannot safely
migrate enabled interrupts from arbitrary contexts. Provide a new irq chip
flag which allows affected hardware to request this.
This has to be opt-in because there have been reports in the past that some
interrupt chips cannot handle affinity setting before startup.
Fixes: 1840475676 ("genirq: Expose default irq affinity mask (take 3)")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.779791738@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3a26242375 ]
Commit 82046702e2 ("efi/libstub/arm64: Replace 'preferred' offset with
alignment check") simplified the way the stub moves the kernel image
around in memory before booting it, given that a relocatable image does
not need to be copied to a 2M aligned offset if it was loaded on a 64k
boundary by EFI.
Commit d32de9130f ("efi/arm64: libstub: Deal gracefully with
EFI_RNG_PROTOCOL failure") inadvertently defeated this logic by
overriding the value of efi_nokaslr if EFI_RNG_PROTOCOL is not
available, which was mistaken by the loader logic as an explicit request
on the part of the user to disable KASLR and any associated relocation
of an Image not loaded on a 2M boundary.
So let's reinstate this functionality, by capturing the value of
efi_nokaslr at function entry to choose the minimum alignment.
Fixes: d32de9130f ("efi/arm64: libstub: Deal gracefully with EFI_RNG_PROTOCOL failure")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5b94046efb ]
Distro versions of GRUB replace the usual LoadImage/StartImage calls
used to load the kernel image with some local code that fails to honor
the allocation requirements described in the PE/COFF header, as it
does not account for the image's BSS section at all: it fails to
allocate space for it, and fails to zero initialize it.
Since the EFI stub itself is allocated in the .init segment, which is
in the middle of the image, its BSS section is not impacted by this,
and the main consequence of this omission is that the BSS section may
overlap with memory regions that are already used by the firmware.
So let's warn about this condition, and force image reallocation to
occur in this case, which works around the problem.
Fixes: 82046702e2 ("efi/libstub/arm64: Replace 'preferred' offset with alignment check")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4152433c39 ]
The EFI stub random allocator used for kaslr on arm64 has a subtle
bug. In function get_entry_num_slots() which counts the number of
possible allocation "slots" for the image in a given chunk of free
EFI memory, "last_slot" can become negative if the chunk is smaller
than the requested allocation size.
The test "if (first_slot > last_slot)" doesn't catch it because
both first_slot and last_slot are unsigned.
I chose not to make them signed to avoid problems if this is ever
used on architectures where there are meaningful addresses with the
top bit set. Instead, fix it with an additional test against the
allocation size.
This can cause a boot failure in addition to a loss of randomisation
due to another bug in the arm64 stub fixed separately.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fixes: 2ddbfc81ea ("efi: stub: add implementation of efi_random_alloc()")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49b0b6ffe2 ]
There's a potential deadlock case when remove the vsock device or
process the RESET event:
vsock_for_each_connected_socket:
spin_lock_bh(&vsock_table_lock) ----------- (1)
...
virtio_vsock_reset_sock:
lock_sock(sk) --------------------- (2)
...
spin_unlock_bh(&vsock_table_lock)
lock_sock() may do initiative schedule when the 'sk' is owned by
other thread at the same time, we would receivce a warning message
that "scheduling while atomic".
Even worse, if the next task (selected by the scheduler) try to
release a 'sk', it need to request vsock_table_lock and the deadlock
occur, cause the system into softlockup state.
Call trace:
queued_spin_lock_slowpath
vsock_remove_bound
vsock_remove_sock
virtio_transport_release
__vsock_release
vsock_release
__sock_release
sock_close
__fput
____fput
So we should not require sk_lock in this case, just like the behavior
in vhost_vsock or vmci.
Fixes: 0ea9e1d3a9 ("VSOCK: Introduce virtio_transport.ko")
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/20210812053056.1699-1-longpeng2@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 88ca2521bd ]
There is a TOCTOU issue in set_evtchn_to_irq. Rows in the evtchn_to_irq
mapping are lazily allocated in this function. The check whether the row
is already present and the row initialization is not synchronized. Two
threads can at the same time allocate a new row for evtchn_to_irq and
add the irq mapping to the their newly allocated row. One thread will
overwrite what the other has set for evtchn_to_irq[row] and therefore
the irq mapping is lost. This will trigger a BUG_ON later in
bind_evtchn_to_cpu:
INFO: pci 0000:1a:15.4: [1d0f:8061] type 00 class 0x010802
INFO: nvme 0000:1a:12.1: enabling device (0000 -> 0002)
INFO: nvme nvme77: 1/0/0 default/read/poll queues
CRIT: kernel BUG at drivers/xen/events/events_base.c:427!
WARN: invalid opcode: 0000 [#1] SMP NOPTI
WARN: Workqueue: nvme-reset-wq nvme_reset_work [nvme]
WARN: RIP: e030:bind_evtchn_to_cpu+0xc2/0xd0
WARN: Call Trace:
WARN: set_affinity_irq+0x121/0x150
WARN: irq_do_set_affinity+0x37/0xe0
WARN: irq_setup_affinity+0xf6/0x170
WARN: irq_startup+0x64/0xe0
WARN: __setup_irq+0x69e/0x740
WARN: ? request_threaded_irq+0xad/0x160
WARN: request_threaded_irq+0xf5/0x160
WARN: ? nvme_timeout+0x2f0/0x2f0 [nvme]
WARN: pci_request_irq+0xa9/0xf0
WARN: ? pci_alloc_irq_vectors_affinity+0xbb/0x130
WARN: queue_request_irq+0x4c/0x70 [nvme]
WARN: nvme_reset_work+0x82d/0x1550 [nvme]
WARN: ? check_preempt_wakeup+0x14f/0x230
WARN: ? check_preempt_curr+0x29/0x80
WARN: ? nvme_irq_check+0x30/0x30 [nvme]
WARN: process_one_work+0x18e/0x3c0
WARN: worker_thread+0x30/0x3a0
WARN: ? process_one_work+0x3c0/0x3c0
WARN: kthread+0x113/0x130
WARN: ? kthread_park+0x90/0x90
WARN: ret_from_fork+0x3a/0x50
This patch sets evtchn_to_irq rows via a cmpxchg operation so that they
will be set only once. The row is now cleared before writing it to
evtchn_to_irq in order to not create a race once the row is visible for
other threads.
While at it, do not require the page to be zeroed, because it will be
overwritten with -1's in clear_evtchn_to_irq_row anyway.
Signed-off-by: Maximilian Heyne <mheyne@amazon.de>
Fixes: d0b075ffee ("xen/events: Refactor evtchn_to_irq array to be dynamically allocated")
Link: https://lore.kernel.org/r/20210812130930.127134-1-mheyne@amazon.de
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24d032e235 ]
The SFC_DONE register lives within the corresponding VD0/VD2/VD4/VD6
forcewake domain and is not accessible if the vdbox in that domain is
fused off and the forcewake is not initialized.
This mistake went unnoticed because until recently we were using the
wrong register offset for the SFC_DONE register; once the register
offset was corrected, we started hitting errors like
<4> [544.989065] i915 0000:cc:00.0: Uninitialized forcewake domain(s) 0x80 accessed at 0x1ce000
on parts with fused-off vdbox engines.
Fixes: e50dbdbfd9 ("drm/i915/tgl: Add SFC instdone to error state")
Fixes: 9c9c6d0ab0 ("drm/i915: Correct SFC_DONE register offset")
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210806174130.1058960-1-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
(cherry picked from commit c5589bb5dc)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[Changed Fixes tag to match the cherry-picked 82929a2140]
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6de035fec0 ]
Currently if BBR congestion control is initialized after more than 2B
packets have been delivered, depending on the phase of the
tp->delivered counter the tracking of BBR round trips can get stuck.
The bug arises because if tp->delivered is between 2^31 and 2^32 at
the time the BBR congestion control module is initialized, then the
initialization of bbr->next_rtt_delivered to 0 will cause the logic to
believe that the end of the round trip is still billions of packets in
the future. More specifically, the following check will fail
repeatedly:
!before(rs->prior_delivered, bbr->next_rtt_delivered)
and thus the connection will take up to 2B packets delivered before
that check will pass and the connection will set:
bbr->round_start = 1;
This could cause many mechanisms in BBR to fail to trigger, for
example bbr_check_full_bw_reached() would likely never exit STARTUP.
This bug is 5 years old and has not been observed, and as a practical
matter this would likely rarely trigger, since it would require
transferring at least 2B packets, or likely more than 3 terabytes of
data, before switching congestion control algorithms to BBR.
This patch is a stable candidate for kernels as far back as v4.9,
when tcp_bbr.c was added.
Fixes: 0f8782ea14 ("tcp_bbr: add BBR congestion control")
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Kevin Yang <yyd@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20210811024056.235161-1-ncardwell@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6922110d15 ]
After migrating my laptop from 4.19-LTS to 5.4-LTS a while ago I noticed
that my Ethernet port to which a bond and a VLAN interface are attached
appeared to remain up after resuming from suspend with the cable unplugged
(and that problem still persists with 5.10-LTS).
It happens that the following happens:
- the network driver (e1000e here) prepares to suspend, calls e1000e_down()
which calls netif_carrier_off() to signal that the link is going down.
- netif_carrier_off() adds a link_watch event to the list of events for
this device
- the device is completely stopped.
- the machine suspends
- the cable is unplugged and the machine brought to another location
- the machine is resumed
- the queued linkwatch events are processed for the device
- the device doesn't yet have the __LINK_STATE_PRESENT bit and its events
are silently dropped
- the device is resumed with its link down
- the upper VLAN and bond interfaces are never notified that the link had
been turned down and remain up
- the only way to provoke a change is to physically connect the machine
to a port and possibly unplug it.
The state after resume looks like this:
$ ip -br li | egrep 'bond|eth'
bond0 UP e8:6a:64:64:64:64 <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP>
eth0 DOWN e8:6a:64:64:64:64 <NO-CARRIER,BROADCAST,MULTICAST,SLAVE,UP>
eth0.2@eth0 UP e8:6a:64:64:64:64 <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP>
Placing an explicit call to netdev_state_change() either in the suspend
or the resume code in the NIC driver worked around this but the solution
is not satisfying.
The issue in fact really is in link_watch that loses events while it
ought not to. It happens that the test for the device being present was
added by commit 124eee3f69 ("net: linkwatch: add check for netdevice
being present to linkwatch_do_dev") in 4.20 to avoid an access to
devices that are not present.
Instead of dropping events, this patch proceeds slightly differently by
postponing their handling so that they happen after the device is fully
resumed.
Fixes: 124eee3f69 ("net: linkwatch: add check for netdevice being present to linkwatch_do_dev")
Link: https://lists.openwall.net/netdev/2018/03/15/62
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Link: https://lore.kernel.org/r/20210809160628.22623-1-w@1wt.eu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45a687879b ]
Ignore fdb flags when adding port extern learn entries and always set
BR_FDB_LOCAL flag when adding bridge extern learn entries. This is
closest to the behaviour we had before and avoids breaking any use cases
which were allowed.
This patch fixes iproute2 calls which assume NUD_PERMANENT and were
allowed before, example:
$ bridge fdb add 00:11:22:33:44:55 dev swp1 extern_learn
Extern learn entries are allowed to roam, but do not expire, so static
or dynamic flags make no sense for them.
Also add a comment for future reference.
Fixes: eb100e0e24 ("net: bridge: allow to add externally learned entries from user-space")
Fixes: 0541a62932 ("net: bridge: validate the NUD_PERMANENT bit when adding an extern_learn FDB entry")
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20210810110010.43859-1-razor@blackwall.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0541a62932 ]
Currently it is possible to add broken extern_learn FDB entries to the
bridge in two ways:
1. Entries pointing towards the bridge device that are not local/permanent:
ip link add br0 type bridge
bridge fdb add 00:01:02:03:04:05 dev br0 self extern_learn static
2. Entries pointing towards the bridge device or towards a port that
are marked as local/permanent, however the bridge does not process the
'permanent' bit in any way, therefore they are recorded as though they
aren't permanent:
ip link add br0 type bridge
bridge fdb add 00:01:02:03:04:05 dev br0 self extern_learn permanent
Since commit 52e4bec155 ("net: bridge: switchdev: treat local FDBs the
same as entries towards the bridge"), these incorrect FDB entries can
even trigger NULL pointer dereferences inside the kernel.
This is because that commit made the assumption that all FDB entries
that are not local/permanent have a valid destination port. For context,
local / permanent FDB entries either have fdb->dst == NULL, and these
point towards the bridge device and are therefore local and not to be
used for forwarding, or have fdb->dst == a net_bridge_port structure
(but are to be treated in the same way, i.e. not for forwarding).
That assumption _is_ correct as long as things are working correctly in
the bridge driver, i.e. we cannot logically have fdb->dst == NULL under
any circumstance for FDB entries that are not local. However, the
extern_learn code path where FDB entries are managed by a user space
controller show that it is possible for the bridge kernel driver to
misinterpret the NUD flags of an entry transmitted by user space, and
end up having fdb->dst == NULL while not being a local entry. This is
invalid and should be rejected.
Before, the two commands listed above both crashed the kernel in this
check from br_switchdev_fdb_notify:
struct net_device *dev = info.is_local ? br->dev : dst->dev;
info.is_local == false, dst == NULL.
After this patch, the invalid entry added by the first command is
rejected:
ip link add br0 type bridge && bridge fdb add 00:01:02:03:04:05 dev br0 self extern_learn static; ip link del br0
Error: bridge: FDB entry towards bridge must be permanent.
and the valid entry added by the second command is properly treated as a
local address and does not crash br_switchdev_fdb_notify anymore:
ip link add br0 type bridge && bridge fdb add 00:01:02:03:04:05 dev br0 self extern_learn permanent; ip link del br0
Fixes: eb100e0e24 ("net: bridge: allow to add externally learned entries from user-space")
Reported-by: syzbot+9ba1174359adba5a5b7c@syzkaller.appspotmail.com
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Link: https://lore.kernel.org/r/20210801231730.7493-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21b52fed92 ]
rtnl_fdb_dump() has logic to split a dump of PF_BRIDGE neighbors into
multiple netlink skbs if the buffer provided by user space is too small
(one buffer will typically handle a few hundred FDB entries).
When the current buffer becomes full, nlmsg_put() in
dsa_slave_port_fdb_do_dump() returns -EMSGSIZE and DSA saves the index
of the last dumped FDB entry, returns to rtnl_fdb_dump() up to that
point, and then the dump resumes on the same port with a new skb, and
FDB entries up to the saved index are simply skipped.
Since dsa_slave_port_fdb_do_dump() is pointed to by the "cb" passed to
drivers, then drivers must check for the -EMSGSIZE error code returned
by it. Otherwise, when a netlink skb becomes full, DSA will no longer
save newly dumped FDB entries to it, but the driver will continue
dumping. So FDB entries will be missing from the dump.
Fix the broken backpressure by propagating the "cb" return code and
allow rtnl_fdb_dump() to restart the FDB dump with a new skb.
Fixes: 291d1e72b7 ("net: dsa: sja1105: Add support for FDB and MDB management")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 871a73a1c8 ]
rtnl_fdb_dump() has logic to split a dump of PF_BRIDGE neighbors into
multiple netlink skbs if the buffer provided by user space is too small
(one buffer will typically handle a few hundred FDB entries).
When the current buffer becomes full, nlmsg_put() in
dsa_slave_port_fdb_do_dump() returns -EMSGSIZE and DSA saves the index
of the last dumped FDB entry, returns to rtnl_fdb_dump() up to that
point, and then the dump resumes on the same port with a new skb, and
FDB entries up to the saved index are simply skipped.
Since dsa_slave_port_fdb_do_dump() is pointed to by the "cb" passed to
drivers, then drivers must check for the -EMSGSIZE error code returned
by it. Otherwise, when a netlink skb becomes full, DSA will no longer
save newly dumped FDB entries to it, but the driver will continue
dumping. So FDB entries will be missing from the dump.
Fix the broken backpressure by propagating the "cb" return code and
allow rtnl_fdb_dump() to restart the FDB dump with a new skb.
Fixes: 58c59ef9e9 ("net: dsa: lantiq: Add Forwarding Database access")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ada2fee185 ]
rtnl_fdb_dump() has logic to split a dump of PF_BRIDGE neighbors into
multiple netlink skbs if the buffer provided by user space is too small
(one buffer will typically handle a few hundred FDB entries).
When the current buffer becomes full, nlmsg_put() in
dsa_slave_port_fdb_do_dump() returns -EMSGSIZE and DSA saves the index
of the last dumped FDB entry, returns to rtnl_fdb_dump() up to that
point, and then the dump resumes on the same port with a new skb, and
FDB entries up to the saved index are simply skipped.
Since dsa_slave_port_fdb_do_dump() is pointed to by the "cb" passed to
drivers, then drivers must check for the -EMSGSIZE error code returned
by it. Otherwise, when a netlink skb becomes full, DSA will no longer
save newly dumped FDB entries to it, but the driver will continue
dumping. So FDB entries will be missing from the dump.
Fix the broken backpressure by propagating the "cb" return code and
allow rtnl_fdb_dump() to restart the FDB dump with a new skb.
Fixes: ab335349b8 ("net: dsa: lan9303: Add port_fast_age and port_fdb_dump methods")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 164844135a ]
Currently ksz8_port_vlan_filtering() sets or clears the VLAN Enable
hardware flag. That controls discarding of packets with a VID that
has not been enabled for any port on the switch.
Since it is a global flag, set the dsa_switch::vlan_filtering_is_global
flag so that the DSA core understands this can't be controlled per
port.
When VLAN filtering is enabled, the switch should also discard packets
with a VID that's not enabled on the ingress port. Set or clear each
external port's VLAN Ingress Filter flag in ksz8_port_vlan_filtering()
to make that happen.
Fixes: e66f840c08 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver")
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c34f674c88 ]
ksz_read64() currently does some dubious byte-swapping on the two
halves of a 64-bit register, and then only returns the high bits.
Replace this with a straightforward expression.
Fixes: e66f840c08 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver")
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 563476ae0c ]
The CQ destroy is performed based on the IRQ number that is stored in
cq->irqn. That number wasn't set explicitly during CQ creation and as
expected some of the API users of mlx5_core_create_cq() forgot to update
it.
This caused to wrong synchronization call of the wrong IRQ with a number
0 instead of the real one.
As a fix, set the IRQ number directly in the mlx5_core_create_cq() and
update all users accordingly.
Fixes: 1a86b377aa ("vdpa/mlx5: Add VDPA driver for supported mlx5 devices")
Fixes: ef1659ade3 ("IB/mlx5: Add DEVX support for CQ events")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ba7f53f8b ]
In some circumstances, such as with bridging, it's possible that the
stack will add the device's own MAC address to its unicast address list.
If, later, the stack deletes this address, the driver will receive a
request to remove this address.
The driver stores its current MAC address as part of the VSI MAC filter
list instead of separately. So, this causes a problem when the device's
MAC address is deleted unexpectedly, which results in traffic failure in
some cases.
The following configuration steps will reproduce the previously
mentioned problem:
> ip link set eth0 up
> ip link add dev br0 type bridge
> ip link set br0 up
> ip addr flush dev eth0
> ip link set eth0 master br0
> echo 1 > /sys/class/net/br0/bridge/vlan_filtering
> modprobe -r veth
> modprobe -r bridge
> ip addr add 192.168.1.100/24 dev eth0
The following ping command fails due to the netdev->dev_addr being
deleted when removing the bridge module.
> ping <link partner>
Fix this by making sure to not delete the netdev->dev_addr during MAC
address sync. After fixing this issue it was noticed that the
netdev_warn() in .set_mac was overly verbose, so make it at
netdev_dbg().
Also, there is a possibility of a race condition between .set_mac and
.set_rx_mode. Fix this by calling netif_addr_lock_bh() and
netif_addr_unlock_bh() on the device's netdev when the netdev->dev_addr
is going to be updated in .set_mac.
Fixes: e94d447866 ("ice: Implement filter sync, NDO operations and bump version")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Liang Li <liali@redhat.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50ac747984 ]
The userspace utility "driverctl" can be used to change/override the
system's default driver choices. This is useful in some situations
(buggy driver, old driver missing a device ID, trying a workaround,
etc.) where the user needs to load a different driver.
However, this is also prone to user error, where a driver is mapped
to a device it's not designed to drive. For example, if the ice driver
is mapped to driver iavf devices, the ice driver crashes.
Add a check to return an error if the ice driver is being used to
probe a virtual function.
Fixes: 837f08fdec ("ice: Add basic driver framework for Intel(R) E800 Series")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d09c548dbf ]
When mirror/redirect a skb to a different port, the ct info should be reset
for reclassification. Or the pkts will match unexpected rules. For example,
with following topology and commands:
-----------
|
veth0 -+-------
|
veth1 -+-------
|
------------
tc qdisc add dev veth0 clsact
# The same with "action mirred egress mirror dev veth1" or "action mirred ingress redirect dev veth1"
tc filter add dev veth0 egress chain 1 protocol ip flower ct_state +trk action mirred ingress mirror dev veth1
tc filter add dev veth0 egress chain 0 protocol ip flower ct_state -inv action ct commit action goto chain 1
tc qdisc add dev veth1 clsact
tc filter add dev veth1 ingress chain 0 protocol ip flower ct_state +trk action drop
ping <remove ip via veth0> &
tc -s filter show dev veth1 ingress
With command 'tc -s filter show', we can find the pkts were dropped on
veth1.
Fixes: b57dc7c13e ("net/sched: Introduce action ct")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f3d65c166 ]
There can be a race between the waiters for a tx work request buffer
and the link down processing that finally clears the link. Although
all waiters are woken up before the link is cleared there might be
waiters which did not yet get back control and are still waiting.
This results in an access to a cleared wait queue head.
Fix this by introducing atomic reference counting around the wait calls,
and wait with the link clear processing until all waiters have finished.
Move the work request layer related calls into smc_wr.c and set the
link state to INACTIVE before calling smcr_link_clear() in
smc_llc_srv_add_link().
Fixes: 15e1b99aad ("net/smc: no WR buffer wait for terminating link group")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2459dcb96b ]
IFLA_IFNAME is nul-term string which means that IFLA_IFNAME buffer can be
larger than length of string which contains.
Function __rtnl_newlink() generates new own ifname if either IFLA_IFNAME
was not specified at all or userspace passed empty nul-term string.
It is expected that if userspace does not specify ifname for new ppp netdev
then kernel generates one in format "ppp<id>" where id matches to the ppp
unit id which can be later obtained by PPPIOCGUNIT ioctl.
And it works in this way if IFLA_IFNAME is not specified at all. But it
does not work when IFLA_IFNAME is specified with empty string.
So fix this logic also for empty IFLA_IFNAME in ppp_nl_newlink() function
and correctly generates ifname based on ppp unit identifier if userspace
did not provided preferred ifname.
Without this patch when IFLA_IFNAME was specified with empty string then
kernel created a new ppp interface in format "ppp<id>" but id did not
match ppp unit id returned by PPPIOCGUNIT ioctl. In this case id was some
number generated by __rtnl_newlink() function.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: bb8082f691 ("ppp: build ifname using unit identifier for rtnl based devices")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2383cb9497 ]
Commit a5e63c7d38 "net: phy: micrel: Fix detection of ksz87xx
switch" broke link detection on the external ports of the KSZ8795.
The previously unused phy_driver structure for these devices specifies
config_aneg and read_status functions that appear to be designed for a
fixed link and do not work with the embedded PHYs in the KSZ8795.
Delete the use of these functions in favour of the generic PHY
implementations which were used previously.
Fixes: a5e63c7d38 ("net: phy: micrel: Fix detection of ksz87xx switch")
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4eb1f4032 ]
In __htab_map_lookup_and_delete_batch(), hash buckets are iterated
over to count the number of elements in each bucket (bucket_size).
If bucket_size is large enough, the multiplication to calculate
kvmalloc() size could overflow, resulting in out-of-bounds write
as reported by KASAN:
[...]
[ 104.986052] BUG: KASAN: vmalloc-out-of-bounds in __htab_map_lookup_and_delete_batch+0x5ce/0xb60
[ 104.986489] Write of size 4194224 at addr ffffc9010503be70 by task crash/112
[ 104.986889]
[ 104.987193] CPU: 0 PID: 112 Comm: crash Not tainted 5.14.0-rc4 #13
[ 104.987552] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014
[ 104.988104] Call Trace:
[ 104.988410] dump_stack_lvl+0x34/0x44
[ 104.988706] print_address_description.constprop.0+0x21/0x140
[ 104.988991] ? __htab_map_lookup_and_delete_batch+0x5ce/0xb60
[ 104.989327] ? __htab_map_lookup_and_delete_batch+0x5ce/0xb60
[ 104.989622] kasan_report.cold+0x7f/0x11b
[ 104.989881] ? __htab_map_lookup_and_delete_batch+0x5ce/0xb60
[ 104.990239] kasan_check_range+0x17c/0x1e0
[ 104.990467] memcpy+0x39/0x60
[ 104.990670] __htab_map_lookup_and_delete_batch+0x5ce/0xb60
[ 104.990982] ? __wake_up_common+0x4d/0x230
[ 104.991256] ? htab_of_map_free+0x130/0x130
[ 104.991541] bpf_map_do_batch+0x1fb/0x220
[...]
In hashtable, if the elements' keys have the same jhash() value, the
elements will be put into the same bucket. By putting a lot of elements
into a single bucket, the value of bucket_size can be increased to
trigger the integer overflow.
Triggering the overflow is possible for both callers with CAP_SYS_ADMIN
and callers without CAP_SYS_ADMIN.
It will be trivial for a caller with CAP_SYS_ADMIN to intentionally
reach this overflow by enabling BPF_F_ZERO_SEED. As this flag will set
the random seed passed to jhash() to 0, it will be easy for the caller
to prepare keys which will be hashed into the same value, and thus put
all the elements into the same bucket.
If the caller does not have CAP_SYS_ADMIN, BPF_F_ZERO_SEED cannot be
used. However, it will be still technically possible to trigger the
overflow, by guessing the random seed value passed to jhash() (32bit)
and repeating the attempt to trigger the overflow. In this case,
the probability to trigger the overflow will be low and will take
a very long time.
Fix the integer overflow by calling kvmalloc_array() instead of
kvmalloc() to allocate memory.
Fixes: 057996380a ("bpf: Add batch ops to all htab bpf map")
Signed-off-by: Tatsuhiko Yasumatsu <th.yasumatsu@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210806150419.109658-1-th.yasumatsu@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d7b132e62 ]
The gpiod_lookup_table.table passed to gpiod_add_lookup_table() must
be terminated with an empty entry, add this.
Note we have likely been getting away with this not being present because
the GPIO lookup code first matches on the dev_id, causing most lookups to
skip checking the table and the lookups which do check the table will
find a matching entry before reaching the end. With that said, terminating
these tables properly still is obviously the correct thing to do.
Fixes: f8eb0235f6 ("x86: pcengines apuv2 gpio/leds/keys platform driver")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210806115515.12184-1-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 704e624f7b ]
On s390, the following build warning occurs:
drivers/net/ethernet/marvell/mvpp2/mvpp2.h:844:2: warning: overflow in
conversion from 'long unsigned int' to 'int' changes value from
'18446744073709551584' to '-32' [-Woverflow]
844 | ((total_size) - MVPP2_SKB_HEADROOM - MVPP2_SKB_SHINFO_SIZE)
This happens because MVPP2_SKB_SHINFO_SIZE, which is 320 bytes (which is
already 64-byte aligned) on some architectures, actually gets ALIGN'd up
to 512 bytes in the s390 case.
So then, when this is invoked:
MVPP2_RX_MAX_PKT_SIZE(MVPP2_BM_SHORT_FRAME_SIZE)
...that turns into:
704 - 224 - 512 == -32
...which is not a good frame size to end up with! The warning above is a
bit lucky: it notices a signed/unsigned bad behavior here, which leads
to the real problem of a frame that is too short for its contents.
Increase MVPP2_BM_SHORT_FRAME_SIZE by 32 (from 704 to 736), which is
just exactly big enough. (The other values can't readily be changed
without causing a lot of other problems.)
Fixes: 07dd0a7aae ("mvpp2: add basic XDP support")
Cc: Sven Auhagen <sven.auhagen@voleatech.de>
Cc: Matteo Croce <mcroce@microsoft.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aff51c5da3 ]
Add the missing RxUnicast counter.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 38ea9def5b ]
It should be added kfree_skb_list() when err is not equal to zero
in nf_br_ip_fragment().
v2: keep this aligned with IPv6.
v3: modify iter.frag_list to iter.frag.
Fixes: 3c171f496e ("netfilter: bridge: add connection tracking system")
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b353bbeae ]
The driver was defining two ALSA controls that both change the same
register field for the wind noise filter corner frequency. The filter
response has two corners, at different frequencies, and the duplicate
controls most likely were an attempt to be able to set the value using
either of the frequencies.
However, having two controls changing the same field can be problematic
and it is unnecessary. Both frequencies are related to each other so
setting one implies exactly what the other would be.
Removing a control affects user-side code, but there is currently no
known use of the removed control so it would be best to remove it now
before it becomes a problem.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2c394ca796 ("ASoC: Add support for CS42L42 codec")
Link: https://lore.kernel.org/r/20210803160834.9005-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 798a315fc3 ]
Some pin doesn't support PUPD register, if it fails and fallbacks with
bias_set_combo case, it will call mtk_pinconf_bias_set_pupd_r1_r0() to
modify the PUPD pin again.
Since the general bias set are either PU/PD or PULLSEL/PULLEN, try
bias_set or bias_set_rev1 for the other fallback case. If the pin
doesn't support neither PU/PD nor PULLSEL/PULLEN, it will return
-ENOTSUPP.
Fixes: 81bd1579b4 ("pinctrl: mediatek: Fix fallback call path")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Link: https://lore.kernel.org/r/20210701080955.2660294-1-hsinyi@chromium.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b93dfa6bda upstream.
Fix the NFIT parsing code to treat a 0 index in a SPA Range Structure as
a special case and not match Region Mapping Structures that use 0 to
indicate that they are not mapped. Without this fix some platform BIOS
descriptions of "virtual disk" ranges do not result in the pmem driver
attaching to the range.
Details:
In addition to typical persistent memory ranges, the ACPI NFIT may also
convey "virtual" ranges. These ranges are indicated by a UUID in the SPA
Range Structure of UUID_VOLATILE_VIRTUAL_DISK, UUID_VOLATILE_VIRTUAL_CD,
UUID_PERSISTENT_VIRTUAL_DISK, or UUID_PERSISTENT_VIRTUAL_CD. The
critical difference between virtual ranges and UUID_PERSISTENT_MEMORY,
is that virtual do not support associations with Region Mapping
Structures. For this reason the "index" value of virtual SPA Range
Structures is allowed to be 0. If a platform BIOS decides to represent
NVDIMMs with disconnected "Region Mapping Structures" (range-index ==
0), the kernel may falsely associate them with standalone ranges where
the "SPA Range Structure Index" is also zero. When this happens the
driver may falsely require labels where "virtual disks" are expected to
be label-less. I.e. "label-less" is where the namespace-range ==
region-range and the pmem driver attaches with no user action to create
a namespace.
Cc: Jacek Zloch <jacek.zloch@intel.com>
Cc: Lukasz Sobieraj <lukasz.sobieraj@intel.com>
Cc: "Lee, Chun-Yi" <jlee@suse.com>
Cc: <stable@vger.kernel.org>
Fixes: c2f32acdf8 ("acpi, nfit: treat virtual ramdisk SPA as pmem region")
Reported-by: Krzysztof Rusocki <krzysztof.rusocki@intel.com>
Reported-by: Damian Bassa <damian.bassa@intel.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Link: https://lore.kernel.org/r/162870796589.2521182.1240403310175570220.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf2ba43221 upstream.
Function ceph_check_delayed_caps() is called from the mdsc->delayed_work
workqueue and it can be kept looping for quite some time if caps keep
being added back to the mdsc->cap_delay_list. This may result in the
watchdog tainting the kernel with the softlockup flag.
This patch breaks this loop if the caps have been recently (i.e. during
the loop execution). Any new caps added to the list will be handled in
the next run.
Also, allow schedule_delayed() callers to explicitly set the delay value
instead of defaulting to 5s, so we can ensure that it runs soon
afterward if it looks like there is more work.
Cc: stable@vger.kernel.org
URL: https://tracker.ceph.com/issues/46284
Signed-off-by: Luis Henriques <lhenriques@suse.de>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a715e8040 upstream.
FPU_STATUS register contains FP exception flags bits which are updated
by core as side-effect of FP instructions but can also be manually
wiggled such as by glibc C99 functions fe{raise,clear,test}except() etc.
To effect the update, the programming model requires OR'ing FWE
bit (31). This bit is write-only and RAZ, meaning it is effectively
auto-cleared after write and thus needs to be set everytime: which
is how glibc implements this.
However there's another usecase of FPU_STATUS update, at the time of
Linux task switch when incoming task value needs to be programmed into
the register. This was added as part of f45ba2bd6d ("ARCv2:
fpu: preserve userspace fpu state") which missed OR'ing FWE bit,
meaning the new value is effectively not being written at all.
This patch remedies that.
Interestingly, this snafu was not caught in interm glibc testing as the
race window which relies on a specific exception bit to be set/clear is
really small specially when it nvolves context switch.
Fortunately this was caught by glibc's math/test-fenv-tls test which
repeatedly set/clear exception flags in a big loop, concurrently in main
program and also in a thread.
Fixes: https://github.com/foss-for-synopsys-dwc-arc-processors/linux/issues/54
Fixes: f45ba2bd6d ("ARCv2: fpu: preserve userspace fpu state")
Cc: stable@vger.kernel.org #5.6+
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit acc68b8d2a upstream.
The CPSW switchdev driver inherited fix from commit 9421c90150 ("net:
ethernet: ti: cpsw: fix min eth packet size") which changes min TX packet
size to 64bytes (VLAN_ETH_ZLEN, excluding ETH_FCS). It was done to fix HW
packed drop issue when packets are sent from Host to the port with PVID and
un-tagging enabled. Unfortunately this breaks some other non-switch
specific use-cases, like:
- [1] CPSW port as DSA CPU port with DSA-tag applied at the end of the
packet
- [2] Some industrial protocols, which expects min TX packet size 60Bytes
(excluding FCS).
Fix it by configuring min TX packet size depending on driver mode
- 60Bytes (ETH_ZLEN) for multi mac (dual-mac) mode
- 64Bytes (VLAN_ETH_ZLEN) for switch mode
and update it during driver mode change and annotate with
READ_ONCE()/WRITE_ONCE() as it can be read by napi while writing.
[1] https://lore.kernel.org/netdev/20210531124051.GA15218@cephalopod/
[2] https://e2e.ti.com/support/arm/sitara_arm/f/791/t/701669
Cc: stable@vger.kernel.org
Fixes: ed3525eda4 ("net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac")
Reported-by: Ben Hutchings <ben.hutchings@essensium.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d3fc01796 upstream.
We used to follow the rule earlier that the create SD context
always be a multiple of 8. However, with the change:
cifs: refactor create_sd_buf() and and avoid corrupting the buffer
...we recompute the length, and we failed that rule.
Fixing that with this change.
Cc: <stable@vger.kernel.org> # v5.10+
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 86ff25ed6c upstream.
If an i2c driver happens to not provide the full amount of data that a
user asks for, it is possible that some uninitialized data could be sent
to userspace. While all in-kernel drivers look to be safe, just be sure
by initializing the buffer to zero before it is passed to the i2c driver
so that any future drivers will not have this issue.
Also properly copy the amount of data recvieved to the userspace buffer,
as pointed out by Dan Carpenter.
Reported-by: Eric Dumazet <edumazet@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c39ca6885 upstream.
The tlv320aic31xx driver relies on regcache_sync() to restore the register
contents after going to _BIAS_OFF, for example during system suspend. This
does not work for the jack detection configuration since that is configured
via the same register that status is read back from so the register is
volatile and not cached. This can also cause issues during init if the jack
detection ends up getting set up before the CODEC is initially brought out
of _BIAS_OFF, we will reset the CODEC and resync the cache as part of that
process.
Fix this by explicitly reapplying the jack detection configuration after
resyncing the register cache during power on.
This issue was found by an engineer working off-list on a product
kernel, I just wrote up the upstream fix.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210723180200.25105-1-broonie@kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 827f3164aa upstream.
Along with the transition to the managed PCM buffers, the driver now
accepts the dynamically allocated buffer, while it still kept the
reference to the old preallocated buffer address. This patch corrects
to the right reference via runtime->dma_addr.
(Although this might have been already buggy before the cleanup with
the managed buffer, let's put Fixes tag to point that; it's a corner
case, after all.)
Fixes: d55894bc27 ("ASoC: uniphier: Use managed buffer allocation")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20210728112353.6675-5-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0d62baa7f upstream.
Printing kernel pointers is discouraged because they might leak kernel
memory layout. This fixes smatch warning:
drivers/net/ethernet/xilinx/xilinx_emaclite.c:1191 xemaclite_of_probe() warn:
argument 4 to %08lX specifier is cast from pointer
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pavel Machek (CIP) <pavel@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 427215d85e upstream.
Add the following checks from __do_loopback() to clone_private_mount() as
well:
- verify that the mount is in the current namespace
- verify that there are no locked children
Reported-by: Alois Wohlschlager <alois1@gmx-topmail.de>
Fixes: c771d683a6 ("vfs: introduce clone_private_mount()")
Cc: <stable@vger.kernel.org> # v3.18
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3125f26c51 upstream.
When registering new ppp interface via PPPIOCNEWUNIT ioctl then kernel has
to choose interface name as this ioctl API does not support specifying it.
Kernel in this case register new interface with name "ppp<id>" where <id>
is the ppp unit id, which can be obtained via PPPIOCGUNIT ioctl. This
applies also in the case when registering new ppp interface via rtnl
without supplying IFLA_IFNAME.
PPPIOCNEWUNIT ioctl allows to specify own ppp unit id which will kernel
assign to ppp interface, in case this ppp id is not already used by other
ppp interface.
In case user does not specify ppp unit id then kernel choose the first free
ppp unit id. This applies also for case when creating ppp interface via
rtnl method as it does not provide a way for specifying own ppp unit id.
If some network interface (does not have to be ppp) has name "ppp<id>"
with this first free ppp id then PPPIOCNEWUNIT ioctl or rtnl call fails.
And registering new ppp interface is not possible anymore, until interface
which holds conflicting name is renamed. Or when using rtnl method with
custom interface name in IFLA_IFNAME.
As list of allocated / used ppp unit ids is not possible to retrieve from
kernel to userspace, userspace has no idea what happens nor which interface
is doing this conflict.
So change the algorithm how ppp unit id is generated. And choose the first
number which is not neither used as ppp unit id nor in some network
interface with pattern "ppp<id>".
This issue can be simply reproduced by following pppd call when there is no
ppp interface registered and also no interface with name pattern "ppp<id>":
pppd ifname ppp1 +ipv6 noip noauth nolock local nodetach pty "pppd +ipv6 noip noauth nolock local nodetach notty"
Or by creating the one ppp interface (which gets assigned ppp unit id 0),
renaming it to "ppp1" and then trying to create a new ppp interface (which
will always fails as next free ppp unit id is 1, but network interface with
name "ppp1" exists).
This patch fixes above described issue by generating new and new ppp unit
id until some non-conflicting id with network interfaces is generated.
Signed-off-by: Pali Rohár <pali@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc0dc8a73e upstream.
The recent fix c4824ae7db ("ALSA: pcm: Fix mmap capability check")
restricts the mmap capability only to the drivers that properly set up
the buffers, but it caused a regression for a few drivers that manage
the buffer on its own way.
For those with UNKNOWN buffer type (i.e. the uninitialized / unused
substream->dma_buffer), just assume that the driver handles the mmap
properly and blindly trust the hardware info bit.
Fixes: c4824ae7db ("ALSA: pcm: Fix mmap capability check")
Reported-and-tested-by: Jeff Woods <jwoods@fnordco.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/s5him0gpghv.wl-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26b75952ca upstream.
Kunpeng920's EHCI controller does not have SBRN register.
Reading the SBRN register when the controller driver is
initialized will get 0.
When rebooting the EHCI driver, ehci_shutdown() will be called.
if the sbrn flag is 0, ehci_shutdown() will return directly.
The sbrn flag being 0 will cause the EHCI interrupt signal to
not be turned off after reboot. this interrupt that is not closed
will cause an exception to the device sharing the interrupt.
Therefore, the EHCI controller of Kunpeng920 needs to skip
the read operation of the SBRN register.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Longfang Liu <liulongfang@huawei.com>
Link: https://lore.kernel.org/r/1617958081-17999-1-git-send-email-liulongfang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab0c29687b upstream
Make vboxsf_dir_create() optionally return the vboxsf-handle for
the created file. This is a preparation patch for adding atomic_open
support.
Fixes: 0fd1695766 ("fs: Add VirtualBox guest shared folder (vboxsf) support")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc3ddee97c upstream
Honor the excl flag to the dir-inode create op, instead of behaving
as if it is always set.
Note the old behavior still worked most of the time since a non-exclusive
open only calls the create op, if there is a race and the file is created
between the dentry lookup and the calling of the create call.
While at it change the type of the is_dir parameter to the
vboxsf_dir_create() helper from an int to a bool, to be consistent with
the use of bool for the excl parameter.
Fixes: 0fd1695766 ("fs: Add VirtualBox guest shared folder (vboxsf) support")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ebc666f39f upstream
The RZ/G2 boards expect there to be an external clock reference for
USB2 EHCI controllers. For the Beacon boards, this reference clock
is controlled by a programmable versaclock. Because the RZ/G2
family has a special clock driver when using an external clock,
the third clock reference in the EHCI node needs to point to this
special clock, called usb2_clksel.
Since the usb2_clksel does not keep the usb_extal clock enabled,
the 4th clock entry for the EHCI nodes needs to reference it to
keep the clock running and make USB functional.
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20210513114617.30191-2-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 19eaad1400 which is
ee0415681e upstream.
This commit is not a stable candidate and was backported without needed
dependencies that results in the resctrl tests unable to compile.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51e1bb9eea upstream.
Back then, commit 96ae522795 ("bpf: Add bpf_probe_write_user BPF helper
to be called in tracers") added the bpf_probe_write_user() helper in order
to allow to override user space memory. Its original goal was to have a
facility to "debug, divert, and manipulate execution of semi-cooperative
processes" under CAP_SYS_ADMIN. Write to kernel was explicitly disallowed
since it would otherwise tamper with its integrity.
One use case was shown in cf9b1199de ("samples/bpf: Add test/example of
using bpf_probe_write_user bpf helper") where the program DNATs traffic
at the time of connect(2) syscall, meaning, it rewrites the arguments to
a syscall while they're still in userspace, and before the syscall has a
chance to copy the argument into kernel space. These days we have better
mechanisms in BPF for achieving the same (e.g. for load-balancers), but
without having to write to userspace memory.
Of course the bpf_probe_write_user() helper can also be used to abuse
many other things for both good or bad purpose. Outside of BPF, there is
a similar mechanism for ptrace(2) such as PTRACE_PEEK{TEXT,DATA} and
PTRACE_POKE{TEXT,DATA}, but would likely require some more effort.
Commit 96ae522795 explicitly dedicated the helper for experimentation
purpose only. Thus, move the helper's availability behind a newly added
LOCKDOWN_BPF_WRITE_USER lockdown knob so that the helper is disabled under
the "integrity" mode. More fine-grained control can be implemented also
from LSM side with this change.
Fixes: 96ae522795 ("bpf: Add bpf_probe_write_user BPF helper to be called in tracers")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 914ab19e47 ]
Implement a .shutdown hook that will be called during a kexec operation
so that the TEE shared memory, session, and context that were set up
during .probe can be properly freed/closed.
Additionally, don't use dma-buf backed shared memory for the
fw_shm_pool. dma-buf backed shared memory cannot be reliably freed and
unregistered during a kexec operation even when tee_shm_free() is called
on the shm from a .shutdown hook. The problem occurs because
dma_buf_put() calls fput() which then uses task_work_add(), with the
TWA_RESUME parameter, to queue tee_shm_release() to be called before the
current task returns to user mode. However, the current task never
returns to user mode before the kexec completes so the memory is never
freed nor unregistered.
Use tee_shm_alloc_kernel_buf() to avoid dma-buf backed shared memory
allocation so that tee_shm_free() can directly call tee_shm_release().
This will ensure that the shm can be freed and unregistered during a
kexec operation.
Fixes: 246880958a ("firmware: broadcom: add OP-TEE based BNXT f/w manager")
Cc: stable@vger.kernel.org
Signed-off-by: Allen Pais <apais@linux.microsoft.com>
Co-developed-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Signed-off-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 376e4199e3 ]
Currently TEE_SHM_DMA_BUF flag has been inappropriately used to not
register shared memory allocated for private usage by underlying TEE
driver: OP-TEE in this case. So rather add a new flag as TEE_SHM_PRIV
that can be utilized by underlying TEE drivers for private allocation
and usage of shared memory.
With this corrected, allow tee_shm_alloc_kernel_buf() to allocate a
shared memory region without the backing of dma-buf.
Cc: stable@vger.kernel.org
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Co-developed-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Signed-off-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 179c6c27bf ]
Use the raw ASID, not ASID-1, when nullifying the last used VMCB when
freeing an SEV ASID. The consumer, pre_sev_run(), indexes the array by
the raw ASID, thus KVM could get a false negative when checking for a
different VMCB if KVM manages to reallocate the same ASID+VMCB combo for
a new VM.
Note, this cannot cause a functional issue _in the current code_, as
pre_sev_run() also checks which pCPU last did VMRUN for the vCPU, and
last_vmentry_cpu is initialized to -1 during vCPU creation, i.e. is
guaranteed to mismatch on the first VMRUN. However, prior to commit
8a14fe4f0c ("kvm: x86: Move last_cpu into kvm_vcpu_arch as
last_vmentry_cpu"), SVM tracked pCPU on its own and zero-initialized the
last_cpu variable. Thus it's theoretically possible that older versions
of KVM could miss a TLB flush if the first VMRUN is on pCPU0 and the ASID
and VMCB exactly match those of a prior VM.
Fixes: 70cd94e60c ("KVM: SVM: VMRUN should use associated ASID when SEV is enabled")
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
See https://github.com/raspberrypi/linux/issues/3981
An unknown unsafe memory access can result in the ep_state variable
in xhci_virt_ep being trampled with a stuck SET_DEQ_PENDING state
despite successful completion of a Set TR Deq Pointer command.
All URB enqueue/dequeue calls for the endpoint will fail in this state
so no transfers are possible until the device is reconnected.
As a workaround, clear the flag if we see it set and issue a new Set
TR Deq command anyway - this should be harmless, as a prior Set TR Deq
command will only have been issued in the Stopped state, and if the
endpoint is Running then the controller is required to ignore it and
respond with a Context State Error event TRB.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
commit e30e8d46cf upstream.
Due to inconsistencies in the way we manipulate compat GPRs, we have a
few issues today:
* For audit and tracing, where error codes are handled as a (native)
long, negative error codes are expected to be sign-extended to the
native 64-bits, or they may fail to be matched correctly. Thus a
syscall which fails with an error may erroneously be identified as
failing.
* For ptrace, *all* compat return values should be sign-extended for
consistency with 32-bit arm, but we currently only do this for
negative return codes.
* As we may transiently set the upper 32 bits of some compat GPRs while
in the kernel, these can be sampled by perf, which is somewhat
confusing. This means that where a syscall returns a pointer above 2G,
this will be sign-extended, but will not be mistaken for an error as
error codes are constrained to the inclusive range [-4096, -1] where
no user pointer can exist.
To fix all of these, we must consistently use helpers to get/set the
compat GPRs, ensuring that we never write the upper 32 bits of the
return code, and always sign-extend when reading the return code. This
patch does so, with the following changes:
* We re-organise syscall_get_return_value() to always sign-extend for
compat tasks, and reimplement syscall_get_error() atop. We update
syscall_trace_exit() to use syscall_get_return_value().
* We consistently use syscall_set_return_value() to set the return
value, ensureing the upper 32 bits are never set unexpectedly.
* As the core audit code currently uses regs_return_value() rather than
syscall_get_return_value(), we special-case this for
compat_user_mode(regs) such that this will do the right thing. Going
forward, we should try to move the core audit code over to
syscall_get_return_value().
Cc: <stable@vger.kernel.org>
Reported-by: He Zhe <zhe.he@windriver.com>
Reported-by: weiyuchen <weiyuchen3@huawei.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20210802104200.21390-1-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
[Mark: trivial conflict resolution for v5.10.y]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f2ad3accef ]
We've gotten a number of reports about backlight control not
working on panels which indicate that they use aux backlight
control. A recent patch:
commit 2d73eabe29
Author: Camille Cho <Camille.Cho@amd.com>
Date: Thu Jul 8 18:28:37 2021 +0800
drm/amd/display: Only set default brightness for OLED
[Why]
We used to unconditionally set backlight path as AUX for panels capable
of backlight adjustment via DPCD in set default brightness.
[How]
This should be limited to OLED panel only since we control backlight via
PWM path for SDR mode in LCD HDR panel.
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Camille Cho <Camille.Cho@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Changes some other code to only use aux for backlight control on
OLED panels. The commit message seems to indicate that PWM should
be used for SDR mode on HDR panels. Do something similar for
backlight control in general. This may need to be revisited if and
when HDR started to get used.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1438
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=213715
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ad4df56cd ]
Clang detected a problem with rc possibly being unitialized
(when length is zero) in a recently added fallocate code path.
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92766c4628 ]
When calling the 'ql_wait_for_drvr_lock' and 'ql_adapter_reset', the driver
has already acquired the spin lock, so the driver should not call 'ssleep'
in atomic context.
This bug can be fixed by using 'mdelay' instead of 'ssleep'.
Reported-by: Letu Ren <fantasquex@gmail.com>
Signed-off-by: Letu Ren <fantasquex@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit caace6ca4e ]
This issue was noticed while debugging a shutdown issue where some
secondary CPUs are not being shutdown correctly. A fix for that [1] requires
that secondary cpus be offlined using the cpu_online_mask so that the
stop operation is a no-op if CPU HOTPLUG is disabled. I, like the author in
[1] looked at the architectures and found that alpha is one of two
architectures that executes smp_send_stop() on all possible CPUs.
On alpha, smp_send_stop() sends an IPI to all possible CPUs but only needs
to send them to online CPUs.
Send the stop IPI to only the online CPUs.
[1] https://lkml.org/lkml/2020/1/10/250
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 795e3d2ea6 ]
The list_for_each_entry() iterator, "vlan" in this code, can never be
NULL so the warning will never be printed.
Signed-off-by: Harshvardhan Jha <harshvardhan.jha@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ecef6a9eff ]
Data transfers are not required to be block aligned in memory, so they
span two pages. Fix this by splitting the call to >sff_data_xfer into
two for that case.
This has been broken since the initial libata import before the damn
of git, but was uncovered by the legacy ide driver removal.
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20210709130237.3730959-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
The backport of c9d9fdbc10 to 5.10 in
6976f3cf34 removed more than it should
have leading to 'batch' being used uninitialised. The 5.13 backport and
the mainline commit did not remove the portion this patch adds back.
Signed-off-by: Jonathan Gray <jsg@jsg.id.au>
Fixes: 6976f3cf34 ("drm/i915: Revert "drm/i915/gem: Asynchronous cmdparser"")
Cc: <stable@vger.kernel.org> # 5.10
Cc: Jason Ekstrand <jason@jlekstrand.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f558c2b834 upstream.
Double enqueues in rt runqueues (list) have been reported while running
a simple test that spawns a number of threads doing a short sleep/run
pattern while being concurrently setscheduled between rt and fair class.
WARNING: CPU: 3 PID: 2825 at kernel/sched/rt.c:1294 enqueue_task_rt+0x355/0x360
CPU: 3 PID: 2825 Comm: setsched__13
RIP: 0010:enqueue_task_rt+0x355/0x360
Call Trace:
__sched_setscheduler+0x581/0x9d0
_sched_setscheduler+0x63/0xa0
do_sched_setscheduler+0xa0/0x150
__x64_sys_sched_setscheduler+0x1a/0x30
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xae
list_add double add: new=ffff9867cb629b40, prev=ffff9867cb629b40,
next=ffff98679fc67ca0.
kernel BUG at lib/list_debug.c:31!
invalid opcode: 0000 [#1] PREEMPT_RT SMP PTI
CPU: 3 PID: 2825 Comm: setsched__13
RIP: 0010:__list_add_valid+0x41/0x50
Call Trace:
enqueue_task_rt+0x291/0x360
__sched_setscheduler+0x581/0x9d0
_sched_setscheduler+0x63/0xa0
do_sched_setscheduler+0xa0/0x150
__x64_sys_sched_setscheduler+0x1a/0x30
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xae
__sched_setscheduler() uses rt_effective_prio() to handle proper queuing
of priority boosted tasks that are setscheduled while being boosted.
rt_effective_prio() is however called twice per each
__sched_setscheduler() call: first directly by __sched_setscheduler()
before dequeuing the task and then by __setscheduler() to actually do
the priority change. If the priority of the pi_top_task is concurrently
being changed however, it might happen that the two calls return
different results. If, for example, the first call returned the same rt
priority the task was running at and the second one a fair priority, the
task won't be removed by the rt list (on_list still set) and then
enqueued in the fair runqueue. When eventually setscheduled back to rt
it will be seen as enqueued already and the WARNING/BUG be issued.
Fix this by calling rt_effective_prio() only once and then reusing the
return value. While at it refactor code as well for clarity. Concurrent
priority inheritance handling is still safe and will eventually converge
to a new state by following the inheritance chain(s).
Fixes: 0782e63bc6 ("sched: Handle priority boosted tasks proper in setscheduler()")
[squashed Peterz changes; added changelog]
Reported-by: Mark Simmons <msimmons@redhat.com>
Signed-off-by: Juri Lelli <juri.lelli@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20210803104501.38333-1-juri.lelli@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df51fe7ea1 upstream.
If we use "perf record" in an AMD Milan guest, dmesg reports a #GP
warning from an unchecked MSR access error on MSR_F15H_PERF_CTLx:
[] unchecked MSR access error: WRMSR to 0xc0010200 (tried to write 0x0000020000110076) at rIP: 0xffffffff8106ddb4 (native_write_msr+0x4/0x20)
[] Call Trace:
[] amd_pmu_disable_event+0x22/0x90
[] x86_pmu_stop+0x4c/0xa0
[] x86_pmu_del+0x3a/0x140
The AMD64_EVENTSEL_HOSTONLY bit is defined and used on the host,
while the guest perf driver should avoid such use.
Fixes: 1018faa6cf ("perf/x86/kvm: Fix Host-Only/Guest-Only counting with SVM disabled")
Signed-off-by: Like Xu <likexu@tencent.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Tested-by: Kim Phillips <kim.phillips@amd.com>
Tested-by: Liam Merwick <liam.merwick@oracle.com>
Link: https://lkml.kernel.org/r/20210802070850.35295-1-likexu@tencent.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8eee86317 upstream.
Sparse reports a compile time warning when dereferencing an
__iomem pointer:
drivers/soc/ixp4xx/ixp4xx-qmgr.c:149:37: warning: dereference of noderef expression
drivers/soc/ixp4xx/ixp4xx-qmgr.c:153:40: warning: dereference of noderef expression
drivers/soc/ixp4xx/ixp4xx-qmgr.c:154:40: warning: dereference of noderef expression
drivers/soc/ixp4xx/ixp4xx-qmgr.c:174:38: warning: dereference of noderef expression
drivers/soc/ixp4xx/ixp4xx-qmgr.c:174:44: warning: dereference of noderef expression
Use __raw_readl() here for consistency with the rest of the file.
This should really get converted to some proper accessor, as the
__raw functions are not meant to be used in drivers, but the driver
has used these since the start, so for the moment, let's only fix
the warning.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: d4c9e9fc97 ("IXP42x: Add QMgr support for IXP425 rev. A0 processors.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce5a595744 upstream.
We currently only enforce BW floors for a subset of nodes in a path.
All BCMs that need updating are queued in the pre_aggregate/aggregate
phase. The first set() commits all queued BCMs and subsequent set()
calls short-circuit without committing anything. Since the floor BW
isn't set in sum_avg/max_peak until set(), then some BCMs are committed
before their associated nodes reflect the floor.
Set the floor as each node is being aggregated. This ensures that all
all relevant floors are set before the BCMs are committed.
Fixes: 266cd33b59 ("interconnect: qcom: Ensure that the floor bandwidth value is enforced")
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
Link: https://lore.kernel.org/r/20210721175432.2119-4-mdtipton@codeaurora.org
[georgi: Removed unused variable]
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8861452b20 upstream.
When compile-testing with 64-bit resource_size_t, gcc reports an invalid
printk format string:
In file included from include/linux/dma-mapping.h:7,
from drivers/soc/ixp4xx/ixp4xx-npe.c:15:
drivers/soc/ixp4xx/ixp4xx-npe.c: In function 'ixp4xx_npe_probe':
drivers/soc/ixp4xx/ixp4xx-npe.c:694:18: error: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'resource_size_t' {aka 'long long unsigned int'} [-Werror=format=]
dev_info(dev, "NPE%d at 0x%08x-0x%08x not available\n",
Use the special %pR format string to print the resources.
Fixes: 0b458d7b10 ("soc: ixp4xx: npe: Pass addresses as resources")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d5aaad6f83 upstream.
Take a signed 'long' instead of an 'unsigned long' for the number of
pages to add/subtract to the total number of pages used by the MMU. This
fixes a zero-extension bug on 32-bit kernels that effectively corrupts
the per-cpu counter used by the shrinker.
Per-cpu counters take a signed 64-bit value on both 32-bit and 64-bit
kernels, whereas kvm_mod_used_mmu_pages() takes an unsigned long and thus
an unsigned 32-bit value on 32-bit kernels. As a result, the value used
to adjust the per-cpu counter is zero-extended (unsigned -> signed), not
sign-extended (signed -> signed), and so KVM's intended -1 gets morphed to
4294967295 and effectively corrupts the counter.
This was found by a staggering amount of sheer dumb luck when running
kvm-unit-tests on a 32-bit KVM build. The shrinker just happened to kick
in while running tests and do_shrink_slab() logged an error about trying
to free a negative number of objects. The truly lucky part is that the
kernel just happened to be a slightly stale build, as the shrinker no
longer yells about negative objects as of commit 18bb473e50 ("mm:
vmscan: shrink deferred objects proportional to priority").
vmscan: shrink_slab: mmu_shrink_scan+0x0/0x210 [kvm] negative objects to delete nr=-858993460
Fixes: bc8a3d8925 ("kvm: mmu: Fix overflow on kvm mmu page limit calculation")
Cc: stable@vger.kernel.org
Cc: Ben Gardon <bgardon@google.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210804214609.1096003-1-seanjc@google.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85cd39af14 upstream.
KVM creates a debugfs directory for each VM in order to store statistics
about the virtual machine. The directory name is built from the process
pid and a VM fd. While generally unique, it is possible to keep a
file descriptor alive in a way that causes duplicate directories, which
manifests as these messages:
[ 471.846235] debugfs: Directory '20245-4' with parent 'kvm' already present!
Even though this should not happen in practice, it is more or less
expected in the case of KVM for testcases that call KVM_CREATE_VM and
close the resulting file descriptor repeatedly and in parallel.
When this happens, debugfs_create_dir() returns an error but
kvm_create_vm_debugfs() goes on to allocate stat data structs which are
later leaked. The slow memory leak was spotted by syzkaller, where it
caused OOM reports.
Since the issue only affects debugfs, do a lookup before calling
debugfs_create_dir, so that the message is downgraded and rate-limited.
While at it, ensure kvm->debugfs_dentry is NULL rather than an error
if it is not created. This fixes kvm_destroy_vm_debugfs, which was not
checking IS_ERR_OR_NULL correctly.
Cc: stable@vger.kernel.org
Fixes: 536a6f88c4 ("KVM: Create debugfs dir and stat files for each VM")
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fa7a549d32 upstream.
Once an exception has been injected, any side effects related to
the exception (such as setting CR2 or DR6) have been taked place.
Therefore, once KVM sets the VM-entry interruption information
field or the AMD EVENTINJ field, the next VM-entry must deliver that
exception.
Pending interrupts are processed after injected exceptions, so
in theory it would not be a problem to use KVM_INTERRUPT when
an injected exception is present. However, DOSEMU is using
run->ready_for_interrupt_injection to detect interrupt windows
and then using KVM_SET_SREGS/KVM_SET_REGS to inject the
interrupt manually. For this to work, the interrupt window
must be delayed after the completion of the previous event
injection.
Cc: stable@vger.kernel.org
Reported-by: Stas Sergeev <stsp2@yandex.ru>
Tested-by: Stas Sergeev <stsp2@yandex.ru>
Fixes: 71cc849b70 ("KVM: x86: Fix split-irqchip vs interrupt injection window request")
Reviewed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec7099fdea upstream.
This reverts commit 3d5bfbd971.
When booting with threadirqs, it causes a splat
WARNING: CPU: 0 PID: 29 at kernel/irq/handle.c:159 __handle_irq_event_percpu+0x1ec/0x27c
irq 66 handler irq_default_primary_handler+0x0/0x1c enabled interrupts
That splat later went away with commit 81e2073c17 ("genirq: Disable
interrupts for force threaded handlers"), which got backported to
-stable. However, when running an -rt kernel, the splat still
exists. Moreover, quoting Thomas Gleixner [1]
But 3d5bfbd971 ("gpio: mpc8xxx: change the gpio interrupt flags.")
has nothing to do with that:
"Delete the interrupt IRQF_NO_THREAD flags in order to gpio interrupts
can be threaded to allow high-priority processes to preempt."
This changelog is blatantly wrong. In mainline forced irq threads
have always been invoked with softirqs disabled, which obviously
makes them non-preemptible.
So the patch didn't even do what its commit log said.
[1] https://lore.kernel.org/lkml/871r8zey88.ffs@nanos.tec.linutronix.de/
Cc: stable@vger.kernel.org # v5.9+
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6d90e9f22 upstream.
Make the RNG on AM3 GP only.
Based on this patch from TI v5.4 tree which is based on hwmod data
which are now removed:
| ARM: AM43xx: hwmod: Move RNG to a GP only links table
|
| On non-GP devices the RNG is controlled by the secure-side software,
| like in DRA7xx hwmod we should not control this IP when we are not
| a GP device.
|
| Signed-off-by: Andrew F. Davis <afd@ti.com>
Cc: stable@vger.kernel.org # v5.10+
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e39cdacf2f upstream.
During the driver loading process, the 'dev' field was not assigned, but
the 'dev' field was referenced in the subsequent 'i82092aa_set_mem_map'
function.
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
CC: <stable@vger.kernel.org>
[linux@dominikbrodowski.net: shorten commit message, add Cc to stable]
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e9505064f upstream.
The attribute-translator has to take in mind maxtype, that is
xfrm_link::nla_max. When it is set, attributes are not of xfrm_attr_type_t.
Currently, they can be only XFRMA_SPD_MAX (message XFRM_MSG_NEWSPDINFO),
their UABI is the same for 64/32-bit, so just copy them.
Thanks to YueHaibing for reporting this:
In xfrm_user_rcv_msg_compat() if maxtype is not zero and less than
XFRMA_MAX, nlmsg_parse_deprecated() do not initialize attrs array fully.
xfrm_xlate32() will access uninit 'attrs[i]' while iterating all attrs
array.
KASAN: probably user-memory-access in range [0x0000000041b58ab0-0x0000000041b58ab7]
CPU: 0 PID: 15799 Comm: syz-executor.2 Tainted: G W 5.14.0-rc1-syzkaller #0
RIP: 0010:nla_type include/net/netlink.h:1130 [inline]
RIP: 0010:xfrm_xlate32_attr net/xfrm/xfrm_compat.c:410 [inline]
RIP: 0010:xfrm_xlate32 net/xfrm/xfrm_compat.c:532 [inline]
RIP: 0010:xfrm_user_rcv_msg_compat+0x5e5/0x1070 net/xfrm/xfrm_compat.c:577
[...]
Call Trace:
xfrm_user_rcv_msg+0x556/0x8b0 net/xfrm/xfrm_user.c:2774
netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2504
xfrm_netlink_rcv+0x6b/0x90 net/xfrm/xfrm_user.c:2824
netlink_unicast_kernel net/netlink/af_netlink.c:1314 [inline]
netlink_unicast+0x533/0x7d0 net/netlink/af_netlink.c:1340
netlink_sendmsg+0x86d/0xdb0 net/netlink/af_netlink.c:1929
sock_sendmsg_nosec net/socket.c:702 [inline]
Fixes: 5106f4a8ac ("xfrm/compat: Add 32=>64-bit messages translator")
Cc: <stable@kernel.org>
Reported-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2580d3f400 upstream.
xfrm_bydst_resize() calls synchronize_rcu() while holding
hash_resize_mutex. But then on PREEMPT_RT configurations,
xfrm_policy_lookup_bytype() may acquire that mutex while running in an
RCU read side critical section. This results in a deadlock.
In fact the scope of hash_resize_mutex is way beyond the purpose of
xfrm_policy_lookup_bytype() to just fetch a coherent and stable policy
for a given destination/direction, along with other details.
The lower level net->xfrm.xfrm_policy_lock, which among other things
protects per destination/direction references to policy entries, is
enough to serialize and benefit from priority inheritance against the
write side. As a bonus, it makes it officially a per network namespace
synchronization business where a policy table resize on namespace A
shouldn't block a policy lookup on namespace B.
Fixes: 77cc278f7b (xfrm: policy: Use sequence counters with associated lock)
Cc: stable@vger.kernel.org
Cc: Ahmed S. Darwish <a.darwish@linutronix.de>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Varad Gautam <varad.gautam@suse.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb7262b295 upstream.
syzbot reported KCSAN data races vs. timer_base::timer_running being set to
NULL without holding base::lock in expire_timers().
This looks innocent and most reads are clearly not problematic, but
Frederic identified an issue which is:
int data = 0;
void timer_func(struct timer_list *t)
{
data = 1;
}
CPU 0 CPU 1
------------------------------ --------------------------
base = lock_timer_base(timer, &flags); raw_spin_unlock(&base->lock);
if (base->running_timer != timer) call_timer_fn(timer, fn, baseclk);
ret = detach_if_pending(timer, base, true); base->running_timer = NULL;
raw_spin_unlock_irqrestore(&base->lock, flags); raw_spin_lock(&base->lock);
x = data;
If the timer has previously executed on CPU 1 and then CPU 0 can observe
base->running_timer == NULL and returns, assuming the timer has completed,
but it's not guaranteed on all architectures. The comment for
del_timer_sync() makes that guarantee. Moving the assignment under
base->lock prevents this.
For non-RT kernel it's performance wise completely irrelevant whether the
store happens before or after taking the lock. For an RT kernel moving the
store under the lock requires an extra unlock/lock pair in the case that
there is a waiter for the timer, but that's not the end of the world.
Reported-by: syzbot+aa7c2385d46c5eba0b89@syzkaller.appspotmail.com
Reported-by: syzbot+abea4558531bae1ba9fe@syzkaller.appspotmail.com
Fixes: 030dcdd197 ("timers: Prepare support for PREEMPT_RT")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/87lfea7gw8.fsf@nanos.tec.linutronix.de
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec6446d530 upstream.
The performance reporting driver added cpu hotplug
feature but it didn't add pmu migration call in cpu
offline function.
This can create an issue incase the current designated
cpu being used to collect fme pmu data got offline,
as based on current code we are not migrating fme pmu to
new target cpu. Because of that perf will still try to
fetch data from that offline cpu and hence we will not
get counter data.
Patch fixed this issue by adding pmu_migrate_context call
in fme_perf_offline_cpu function.
Fixes: 724142f8c4 ("fpga: dfl: fme: add performance reporting support")
Cc: stable@vger.kernel.org
Tested-by: Xu Yilun <yilun.xu@intel.com>
Acked-by: Wu Hao <hao.wu@intel.com>
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 341abd693d upstream.
This attempts to fix a bug found with a serial port card which uses
an MCS9922 chip, one of the 4 models for which MSI-X interrupts are
currently supported. I don't possess such a card, and i'm not
experienced with the serial subsystem, so this patch is based on what
i think i found as a likely reason for failure, based on walking the
user who actually owns the card through some diagnostic.
The user who reported the problem finds the following in his dmesg
output for the relevant ttyS4 and ttyS5:
[ 0.580425] serial 0000:02:00.0: enabling device (0000 -> 0003)
[ 0.601448] 0000:02:00.0: ttyS4 at I/O 0x3010 (irq = 125, base_baud = 115200) is a ST16650V2
[ 0.603089] serial 0000:02:00.1: enabling device (0000 -> 0003)
[ 0.624119] 0000:02:00.1: ttyS5 at I/O 0x3000 (irq = 126, base_baud = 115200) is a ST16650V2
...
[ 6.323784] genirq: Flags mismatch irq 128. 00000080 (ttyS5) vs. 00000000 (xhci_hcd)
[ 6.324128] genirq: Flags mismatch irq 128. 00000080 (ttyS5) vs. 00000000 (xhci_hcd)
...
Output of setserial -a:
/dev/ttyS4, Line 4, UART: 16650V2, Port: 0x3010, IRQ: 127
Baud_base: 115200, close_delay: 50, divisor: 0
closing_wait: 3000
Flags: spd_normal skip_test
This suggests to me that the serial driver wants to register and share a
MSI/MSI-X irq 128 with the xhci_hcd driver, whereas the xhci driver does
not want to share the irq, as flags 0x00000080 (== IRQF_SHARED) from the
serial port driver means to share the irq, and this mismatch ends in some
failed irq init?
With this setup, data reception works very unreliable, with dropped data,
already at a transmission rate of only a 16 Bytes chunk every 1/120th of
a second, ie. 1920 Bytes/sec, presumably due to rx fifo overflow due to
mishandled or not used at all rx irq's?
See full discussion thread with attempted diagnosis at:
https://psychtoolbox.discourse.group/t/issues-with-iscan-serial-port-recording/3886
Disabling the use of MSI interrupts for the serial port pci card did
fix the reliability problems. The user executed the following sequence
of commands to achieve this:
echo 0000:02:00.0 | sudo tee /sys/bus/pci/drivers/serial/unbind
echo 0000:02:00.1 | sudo tee /sys/bus/pci/drivers/serial/unbind
echo 0 | sudo tee /sys/bus/pci/devices/0000:02:00.0/msi_bus
echo 0 | sudo tee /sys/bus/pci/devices/0000:02:00.1/msi_bus
echo 0000:02:00.0 | sudo tee /sys/bus/pci/drivers/serial/bind
echo 0000:02:00.1 | sudo tee /sys/bus/pci/drivers/serial/bind
This resulted in the following log output:
[ 82.179021] pci 0000:02:00.0: MSI/MSI-X disallowed for future drivers
[ 87.003031] pci 0000:02:00.1: MSI/MSI-X disallowed for future drivers
[ 98.537010] 0000:02:00.0: ttyS4 at I/O 0x3010 (irq = 17, base_baud = 115200) is a ST16650V2
[ 103.648124] 0000:02:00.1: ttyS5 at I/O 0x3000 (irq = 18, base_baud = 115200) is a ST16650V2
This patch attempts to fix the problem by disabling irq sharing when
using MSI irq's. Note that all i know for sure is that disabling MSI
irq's fixed the problem for the user, so this patch could be wrong and
is untested. Please review with caution, keeping this in mind.
Fixes: 8428413b1d ("serial: 8250_pci: Implement MSI(-X) support")
Cc: Ralf Ramsauer <ralf.ramsauer@oth-regensburg.de>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Link: https://lore.kernel.org/r/20210729043306.18528-1-mario.kleiner.de@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a936d6c3d upstream.
Correct big-endian accesses to the CBUS UART, a Malta on-board discrete
TI16C550C part wired directly to the system controller's device bus, and
do not use byte swapping with the 32-bit accesses to the device.
The CBUS is used for devices such as the boot flash memory needed early
on in system bootstrap even before PCI has been initialised. Therefore
it uses the system controller's device bus, which follows the endianness
set with the CPU, which means no byte-swapping is ever required for data
accesses to CBUS, unlike with PCI.
The CBUS UART uses the UPIO_MEM32 access method, that is the `readl' and
`writel' MMIO accessors, which on the MIPS platform imply byte-swapping
with PCI systems. Consequently the wrong byte lane is accessed with the
big-endian configuration and the UART is not correctly accessed.
As it happens the UPIO_MEM32BE access method makes use of the `ioread32'
and `iowrite32' MMIO accessors, which still use `readl' and `writel'
respectively, however they byte-swap data passed, effectively cancelling
swapping done with the accessors themselves and making it suitable for
the CBUS UART.
Make the CBUS UART switch between UPIO_MEM32 and UPIO_MEM32BE then,
based on the endianness selected. With this change in place the device
is correctly recognised with big-endian Malta at boot, along with the
Super I/O devices behind PCI:
Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled
printk: console [ttyS0] disabled
serial8250.0: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
printk: console [ttyS0] enabled
printk: bootconsole [uart8250] disabled
serial8250.0: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A
serial8250.0: ttyS2 at MMIO 0x1f000900 (irq = 20, base_baud = 230400) is a 16550A
Fixes: e7c4782f92 ("[MIPS] Put an end to <asm/serial.h>'s long and annyoing existence")
Cc: stable@vger.kernel.org # v2.6.23+
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260524430.37803@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5227c5109 upstream.
Make sure only actual 8 bits of the IIR register are used in determining
the port type in `autoconfig'.
The `serial_in' port accessor returns the `unsigned int' type, meaning
that with UPIO_AU, UPIO_MEM16, UPIO_MEM32, and UPIO_MEM32BE access types
more than 8 bits of data are returned, of which the high order bits will
often come from bus lines that are left floating in the data phase. For
example with the MIPS Malta board's CBUS UART, where the registers are
aligned on 8-byte boundaries and which uses 32-bit accesses, data as
follows is returned:
YAMON> dump -32 0xbf000900 0x40
BF000900: 1F000942 1F000942 1F000900 1F000900 ...B...B........
BF000910: 1F000901 1F000901 1F000900 1F000900 ................
BF000920: 1F000900 1F000900 1F000960 1F000960 ...........`...`
BF000930: 1F000900 1F000900 1F0009FF 1F0009FF ................
YAMON>
Evidently high-order 24 bits return values previously driven in the
address phase (the 3 highest order address bits used with the command
above are masked out in the simple virtual address mapping used here and
come out at zeros on the external bus), a common scenario with bus lines
left floating, due to bus capacitance.
Consequently when the value of IIR, mapped at 0x1f000910, is retrieved
in `autoconfig', it comes out at 0x1f0009c1 and when it is right-shifted
by 6 and then assigned to 8-bit `scratch' variable, the value calculated
is 0x27, not one of 0, 1, 2, 3 expected in port type determination.
Fix the issue then, by assigning the value returned from `serial_in' to
`scratch' first, which masks out 24 high-order bits retrieved, and only
then right-shift the resulting 8-bit data quantity, producing the value
of 3 in this case, as expected. Fix the same issue in `serial_dl_read'.
The problem first appeared with Linux 2.6.9-rc3 which predates our repo
history, but the origin could be identified with the old MIPS/Linux repo
also at: <git://git.kernel.org/pub/scm/linux/kernel/git/ralf/linux.git>
as commit e0d2356c0777 ("Merge with Linux 2.6.9-rc3."), where code in
`serial_in' was updated with this case:
+ case UPIO_MEM32:
+ return readl(up->port.membase + offset);
+
which made it produce results outside the unsigned 8-bit range for the
first time, though obviously it is system dependent what actual values
appear in the high order bits retrieved and it may well have been zeros
in the relevant positions with the system the change originally was
intended for. It is at that point that code in `autoconf' should have
been updated accordingly, but clearly it was overlooked.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org # v2.6.12+
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260516220.37803@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c4a509d38 upstream.
Fix uart corruption issue when rx power off.
Add spin lock in mtk8250_dma_rx_complete function in APDMA mode.
when uart is used as a communication port with external device(GPS).
when external device(GPS) power off, the power of rx pin is also from
1.8v to 0v. Even if there is not any data in rx. But uart rx pin can
capture the data "0".
If uart don't receive any data in specified cycle, uart will generates
BI(Break interrupt) interrupt.
If external device(GPS) power off, we found that BI interrupt appeared
continuously and very frequently.
When uart interrupt type is BI, uart IRQ handler(8250 framwork
API:serial8250_handle_irq) will push data to tty buffer.
mtk8250_dma_rx_complete is a task of mtk_uart_apdma_rx_handler.
mtk8250_dma_rx_complete priority is lower than uart irq
handler(serial8250_handle_irq).
if we are in process of mtk8250_dma_rx_complete, uart appear BI
interrupt:1)serial8250_handle_irq will priority execution.2)it may cause
write tty buffer conflict in mtk8250_dma_rx_complete.
So the spin lock protect the rx receive data process is not break.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210729084640.17613-2-zhiyong.tao@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 877ba3f729 upstream.
Commit b5776e7524 ("ext4: fix potential htree index checksum
corruption) removed a required restart when multiple levels of index
nodes need to be split. Fix this to avoid directory htree corruptions
when using the large_dir feature.
Cc: stable@kernel.org # v5.11
Cc: Благодаренко Артём <artem.blagodarenko@gmail.com>
Fixes: b5776e7524 ("ext4: fix potential htree index checksum corruption)
Reported-by: Denis <denis@voxelsoft.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 76f22c93b2 upstream.
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Control transfers without a data stage are treated as OUT requests by
the USB stack and should be using usb_sndctrlpipe(). Failing to do so
will now trigger a warning.
The driver uses a zero-length i2c-read request for type detection so
update the control-request code to use usb_sndctrlpipe() in this case.
Note that actually trying to read the i2c register in question does not
work as the register might not exist (e.g. depending on the demodulator)
as reported by Eero Lehtinen <debiangamer2@gmail.com>.
Reported-by: syzbot+faf11bbadc5a372564da@syzkaller.appspotmail.com
Reported-by: Eero Lehtinen <debiangamer2@gmail.com>
Tested-by: Eero Lehtinen <debiangamer2@gmail.com>
Fixes: d0f232e823 ("[media] rtl28xxu: add heuristic to detect chip type")
Cc: stable@vger.kernel.org # 4.0
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4d1014c181 upstream.
dma_range_map is freed to early, which might cause an oops when
a driver probe fails.
Call trace:
is_free_buddy_page+0xe4/0x1d4
__free_pages+0x2c/0x88
dma_free_contiguous+0x64/0x80
dma_direct_free+0x38/0xb4
dma_free_attrs+0x88/0xa0
dmam_release+0x28/0x34
release_nodes+0x78/0x8c
devres_release_all+0xa8/0x110
really_probe+0x118/0x2d0
__driver_probe_device+0xc8/0xe0
driver_probe_device+0x54/0xec
__driver_attach+0xe0/0xf0
bus_for_each_dev+0x7c/0xc8
driver_attach+0x30/0x3c
bus_add_driver+0x17c/0x1c4
driver_register+0xc0/0xf8
__platform_driver_register+0x34/0x40
...
This issue is introduced by commit d0243bbd5d ("drivers core:
Free dma_range_map when driver probe failed"). It frees
dma_range_map before the call to devres_release_all, which is too
early. The solution is to free dma_range_map only after
devres_release_all.
Fixes: d0243bbd5d ("drivers core: Free dma_range_map when driver probe failed")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Filip Schauer <filip@mg6.at>
Link: https://lore.kernel.org/r/20210727112311.GA7645@DESKTOP-E8BN1B0.localdomain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9e6aa51b2 upstream.
There was strange error handling logic in case of fw load failure. For
some reason fw loader callback was doing clean up stuff when fw is not
available. I don't see any reason behind doing this. Since this driver
doesn't have EEPROM firmware let's just disconnect it in case of fw load
failure. Doing clean up stuff in 2 different place which can run
concurently is not good idea and syzbot found 2 bugs related to this
strange approach.
So, in this pacth I deleted all clean up code from fw callback and made
a call to device_release_driver() under device_lock(parent) in case of fw
load failure. This approach is more generic and it defend driver from UAF
bugs, since all clean up code is moved to one place.
Fixes: e02a3b9458 ("staging: rtl8712: fix memory leak in rtl871x_load_fw_cb")
Fixes: 8c213fa591 ("staging: r8712u: Use asynchronous firmware loading")
Cc: stable <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+5872a520e0ce0a7c7230@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+cc699626e48a6ebaf295@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/d49ecc56e97c4df181d7bd4d240b031f315eacc3.1626895918.git.paskripkin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dfb703ad2a upstream.
dma-buf backed shared memory cannot be reliably freed and unregistered
during a kexec operation even when tee_shm_free() is called on the shm
from a .shutdown hook. The problem occurs because dma_buf_put() calls
fput() which then uses task_work_add(), with the TWA_RESUME parameter,
to queue tee_shm_release() to be called before the current task returns
to user mode. However, the current task never returns to user mode
before the kexec completes so the memory is never freed nor
unregistered.
Use tee_shm_alloc_kernel_buf() to avoid dma-buf backed shared memory
allocation so that tee_shm_free() can directly call tee_shm_release().
This will ensure that the shm can be freed and unregistered during a
kexec operation.
Fixes: 09e574831b ("tpm/tpm_ftpm_tee: A driver for firmware TPM running inside TEE")
Fixes: 1760eb689e ("tpm/tpm_ftpm_tee: add shutdown call back")
Cc: stable@vger.kernel.org
Signed-off-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Acked-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit adf752af45 upstream.
Fix a hung task issue, seen when booting the kdump kernel, that is
caused by all of the secure world threads being in a permanent suspended
state:
INFO: task swapper/0:1 blocked for more than 120 seconds.
Not tainted 5.4.83 #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
swapper/0 D 0 1 0 0x00000028
Call trace:
__switch_to+0xc8/0x118
__schedule+0x2e0/0x700
schedule+0x38/0xb8
schedule_timeout+0x258/0x388
wait_for_completion+0x16c/0x4b8
optee_cq_wait_for_completion+0x28/0xa8
optee_disable_shm_cache+0xb8/0xf8
optee_probe+0x560/0x61c
platform_drv_probe+0x58/0xa8
really_probe+0xe0/0x338
driver_probe_device+0x5c/0xf0
device_driver_attach+0x74/0x80
__driver_attach+0x64/0xe0
bus_for_each_dev+0x84/0xd8
driver_attach+0x30/0x40
bus_add_driver+0x188/0x1e8
driver_register+0x64/0x110
__platform_driver_register+0x54/0x60
optee_driver_init+0x20/0x28
do_one_initcall+0x54/0x24c
kernel_init_freeable+0x1e8/0x2c0
kernel_init+0x18/0x118
ret_from_fork+0x10/0x18
The invoke_fn hook returned OPTEE_SMC_RETURN_ETHREAD_LIMIT, indicating
that the secure world threads were all in a suspended state at the time
of the kernel crash. This intermittently prevented the kdump kernel from
booting, resulting in a failure to collect the kernel dump.
Make kernel dump collection more reliable on systems utilizing OP-TEE by
refusing to load the driver under the kdump kernel.
Cc: stable@vger.kernel.org
Signed-off-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5c10dd04b upstream.
The shm cache could contain invalid addresses if
optee_disable_shm_cache() was not called from the .shutdown hook of the
previous kernel before a kexec. These addresses could be unmapped or
they could point to mapped but unintended locations in memory.
Clear the shared memory cache, while being careful to not translate the
addresses returned from OPTEE_SMC_DISABLE_SHM_CACHE, during driver
initialization. Once all pre-cache shm objects are removed, proceed with
enabling the cache so that we know that we can handle cached shm objects
with confidence later in the .shutdown hook.
Cc: stable@vger.kernel.org
Signed-off-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c32706dac upstream.
When the function_graph tracer is in use, arch_stack_walk() may unwind
the stack incorrectly, erroneously reporting itself, missing the final
entry which is being traced, and reporting all traced entries between
these off-by-one from where they should be.
When ftrace hooks a function return, the original return address is
saved to the fgraph ret_stack, and the return address in the LR (or the
function's frame record) is replaced with `return_to_handler`.
When arm64's unwinder encounter frames returning to `return_to_handler`,
it finds the associated original return address from the fgraph ret
stack, assuming the most recent `ret_to_hander` entry on the stack
corresponds to the most recent entry in the fgraph ret stack, and so on.
When arch_stack_walk() is used to dump the current task's stack, it
starts from the caller of arch_stack_walk(). However, arch_stack_walk()
can be traced, and so may push an entry on to the fgraph ret stack,
leaving the fgraph ret stack offset by one from the expected position.
This can be seen when dumping the stack via /proc/self/stack, where
enabling the graph tracer results in an unexpected
`stack_trace_save_tsk` entry at the start of the trace, and `el0_svc`
missing form the end of the trace.
This patch fixes this by marking arch_stack_walk() as notrace, as we do
for all other functions on the path to ftrace_graph_get_ret_stack().
While a few helper functions are not marked notrace, their calls/returns
are balanced, and will have no observable effect when examining the
fgraph ret stack.
It is possible for an exeption boundary to cause a similar offset if the
return address of the interrupted context was in the LR. Fixing those
cases will require some more substantial rework, and is left for
subsequent patches.
Before:
| # cat /proc/self/stack
| [<0>] proc_pid_stack+0xc4/0x140
| [<0>] proc_single_show+0x6c/0x120
| [<0>] seq_read_iter+0x240/0x4e0
| [<0>] seq_read+0xe8/0x140
| [<0>] vfs_read+0xb8/0x1e4
| [<0>] ksys_read+0x74/0x100
| [<0>] __arm64_sys_read+0x28/0x3c
| [<0>] invoke_syscall+0x50/0x120
| [<0>] el0_svc_common.constprop.0+0xc4/0xd4
| [<0>] do_el0_svc+0x30/0x9c
| [<0>] el0_svc+0x2c/0x54
| [<0>] el0t_64_sync_handler+0x1a8/0x1b0
| [<0>] el0t_64_sync+0x198/0x19c
| # echo function_graph > /sys/kernel/tracing/current_tracer
| # cat /proc/self/stack
| [<0>] stack_trace_save_tsk+0xa4/0x110
| [<0>] proc_pid_stack+0xc4/0x140
| [<0>] proc_single_show+0x6c/0x120
| [<0>] seq_read_iter+0x240/0x4e0
| [<0>] seq_read+0xe8/0x140
| [<0>] vfs_read+0xb8/0x1e4
| [<0>] ksys_read+0x74/0x100
| [<0>] __arm64_sys_read+0x28/0x3c
| [<0>] invoke_syscall+0x50/0x120
| [<0>] el0_svc_common.constprop.0+0xc4/0xd4
| [<0>] do_el0_svc+0x30/0x9c
| [<0>] el0t_64_sync_handler+0x1a8/0x1b0
| [<0>] el0t_64_sync+0x198/0x19c
After:
| # cat /proc/self/stack
| [<0>] proc_pid_stack+0xc4/0x140
| [<0>] proc_single_show+0x6c/0x120
| [<0>] seq_read_iter+0x240/0x4e0
| [<0>] seq_read+0xe8/0x140
| [<0>] vfs_read+0xb8/0x1e4
| [<0>] ksys_read+0x74/0x100
| [<0>] __arm64_sys_read+0x28/0x3c
| [<0>] invoke_syscall+0x50/0x120
| [<0>] el0_svc_common.constprop.0+0xc4/0xd4
| [<0>] do_el0_svc+0x30/0x9c
| [<0>] el0_svc+0x2c/0x54
| [<0>] el0t_64_sync_handler+0x1a8/0x1b0
| [<0>] el0t_64_sync+0x198/0x19c
| # echo function_graph > /sys/kernel/tracing/current_tracer
| # cat /proc/self/stack
| [<0>] proc_pid_stack+0xc4/0x140
| [<0>] proc_single_show+0x6c/0x120
| [<0>] seq_read_iter+0x240/0x4e0
| [<0>] seq_read+0xe8/0x140
| [<0>] vfs_read+0xb8/0x1e4
| [<0>] ksys_read+0x74/0x100
| [<0>] __arm64_sys_read+0x28/0x3c
| [<0>] invoke_syscall+0x50/0x120
| [<0>] el0_svc_common.constprop.0+0xc4/0xd4
| [<0>] do_el0_svc+0x30/0x9c
| [<0>] el0_svc+0x2c/0x54
| [<0>] el0t_64_sync_handler+0x1a8/0x1b0
| [<0>] el0t_64_sync+0x198/0x19c
Cc: <stable@vger.kernel.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Madhavan T. Venkataraman <madvenka@linux.microsoft.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Will Deacon <will@kernel.org>
Reviwed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210802164845.45506-3-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 231264d692 upstream.
On a 1->0->1 callbacks transition, there is an issue with the new
callback using the old callback's data.
Considering __DO_TRACE_CALL:
do { \
struct tracepoint_func *it_func_ptr; \
void *__data; \
it_func_ptr = \
rcu_dereference_raw((&__tracepoint_##name)->funcs); \
if (it_func_ptr) { \
__data = (it_func_ptr)->data; \
----> [ delayed here on one CPU (e.g. vcpu preempted by the host) ]
static_call(tp_func_##name)(__data, args); \
} \
} while (0)
It has loaded the tp->funcs of the old callback, so it will try to use the old
data. This can be fixed by adding a RCU sync anywhere in the 1->0->1
transition chain.
On a N->2->1 transition, we need an rcu-sync because you may have a
sequence of 3->2->1 (or 1->2->1) where the element 0 data is unchanged
between 2->1, but was changed from 3->2 (or from 1->2), which may be
observed by the static call. This can be fixed by adding an
unconditional RCU sync in transition 2->1.
Note, this fixes a correctness issue at the cost of adding a tremendous
performance regression to the disabling of tracepoints.
Before this commit:
# trace-cmd start -e all
# time trace-cmd start -p nop
real 0m0.778s
user 0m0.000s
sys 0m0.061s
After this commit:
# trace-cmd start -e all
# time trace-cmd start -p nop
real 0m10.593s
user 0m0.017s
sys 0m0.259s
A follow up fix will introduce a more lightweight scheme based on RCU
get_state and cond_sync, that will return the performance back to what it
was. As both this change and the lightweight versions are complex on their
own, for bisecting any issues that this may cause, they are kept as two
separate changes.
Link: https://lkml.kernel.org/r/20210805132717.23813-3-mathieu.desnoyers@efficios.com
Link: https://lore.kernel.org/io-uring/4ebea8f0-58c9-e571-fd30-0ce4f6f09c70@samba.org/
Cc: stable@vger.kernel.org
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: "Paul E. McKenney" <paulmck@kernel.org>
Cc: Stefan Metzmacher <metze@samba.org>
Fixes: d25e37d89d ("tracepoint: Optimize using static_call()")
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff41c28c4b upstream.
The event_trace_add_tracer() can fail. In this case, it leads to a crash
in start_creating with below call stack. Handle the error scenario
properly in trace_array_create_dir.
Call trace:
down_write+0x7c/0x204
start_creating.25017+0x6c/0x194
tracefs_create_file+0xc4/0x2b4
init_tracer_tracefs+0x5c/0x940
trace_array_create_dir+0x58/0xb4
trace_array_create+0x1bc/0x2b8
trace_array_get_by_name+0xdc/0x18c
Link: https://lkml.kernel.org/r/1627651386-21315-1-git-send-email-kamaagra@codeaurora.org
Cc: stable@vger.kernel.org
Fixes: 4114fbfd02 ("tracing: Enable creating new instance early boot")
Signed-off-by: Kamal Agrawal <kamaagra@codeaurora.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c05caa7ba upstream.
When working on my user space applications, I found a bug in the synthetic
event code where the automated synthetic event field was not matching the
event field calculation it was attached to. Looking deeper into it, it was
because the calculation hist_field was not given a size.
The synthetic event fields are matched to their hist_fields either by
having the field have an identical string type, or if that does not match,
then the size and signed values are used to match the fields.
The problem arose when I tried to match a calculation where the fields
were "unsigned int". My tool created a synthetic event of type "u32". But
it failed to match. The string was:
diff=field1-field2:onmatch(event).trace(synth,$diff)
Adding debugging into the kernel, I found that the size of "diff" was 0.
And since it was given "unsigned int" as a type, the histogram fallback
code used size and signed. The signed matched, but the size of u32 (4) did
not match zero, and the event failed to be created.
This can be worse if the field you want to match is not one of the
acceptable fields for a synthetic event. As event fields can have any type
that is supported in Linux, this can cause an issue. For example, if a
type is an enum. Then there's no way to use that with any calculations.
Have the calculation field simply take on the size of what it is
calculating.
Link: https://lkml.kernel.org/r/20210730171951.59c7743f@oasis.local.home
Cc: Tom Zanussi <zanussi@kernel.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@vger.kernel.org
Fixes: 100719dcef ("tracing: Add simple expression support to hist triggers")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf88fef0b6 upstream.
The HNP work can be re-scheduled while it's still in-fly. This results in
re-initialization of the busy work, resetting the hrtimer's list node of
the work and crashing kernel with null dereference within kernel/timer
once work's timer is expired. It's very easy to trigger this problem by
re-plugging USB cable quickly. Initialize HNP work only once to fix this
trouble.
Unable to handle kernel NULL pointer dereference at virtual address 00000126)
...
PC is at __run_timers.part.0+0x150/0x228
LR is at __next_timer_interrupt+0x51/0x9c
...
(__run_timers.part.0) from [<c0187a2b>] (run_timer_softirq+0x2f/0x50)
(run_timer_softirq) from [<c01013ad>] (__do_softirq+0xd5/0x2f0)
(__do_softirq) from [<c012589b>] (irq_exit+0xab/0xb8)
(irq_exit) from [<c0170341>] (handle_domain_irq+0x45/0x60)
(handle_domain_irq) from [<c04c4a43>] (gic_handle_irq+0x6b/0x7c)
(gic_handle_irq) from [<c0100b65>] (__irq_svc+0x65/0xac)
Cc: stable@vger.kernel.org
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210717182134.30262-6-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit afcff6dc69 upstream.
The USB HID standard declares mandatory support for GET_IDLE and SET_IDLE
requests for Boot Keyboard. Most hosts can handle their absence, but others
like some old/strange UEFIs and BIOSes consider this a critical error
and refuse to work with f_hid.
This primitive implementation of saving and returning idle is sufficient
to meet the requirements of the standard and these devices.
Acked-by: Felipe Balbi <balbi@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Maxim Devaev <mdevaev@gmail.com>
Link: https://lore.kernel.org/r/20210721180351.129450-1-mdevaev@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cb10f68ad8 upstream.
If the device is already in the runtime suspended state, any call to
the pullup routine will issue a runtime resume on the DWC3 core
device. If the USB gadget is disabling the pullup, then avoid having
to issue a runtime resume, as DWC3 gadget has already been
halted/stopped.
This fixes an issue where the following condition occurs:
usb_gadget_remove_driver()
-->usb_gadget_disconnect()
-->dwc3_gadget_pullup(0)
-->pm_runtime_get_sync() -> ret = 0
-->pm_runtime_put() [async]
-->usb_gadget_udc_stop()
-->dwc3_gadget_stop()
-->dwc->gadget_driver = NULL
...
dwc3_suspend_common()
-->dwc3_gadget_suspend()
-->DWC3 halt/stop routine skipped, driver_data == NULL
This leads to a situation where the DWC3 gadget is not properly
stopped, as the runtime resume would have re-enabled EP0 and event
interrupts, and since we avoided the DWC3 gadget suspend, these
resources were never disabled.
Fixes: 77adb8bdf4 ("usb: dwc3: gadget: Allow runtime suspend if UDC unbinded")
Cc: stable <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1628058245-30692-1-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66291b6adb upstream.
The change to restore the autosuspend from the disabled state uses a
wrong check: namely, it should have been the exact comparison of the
quirk_type instead of the bitwise and (&). Otherwise it matches
wrongly with the other quirk types.
Although re-enabling the autosuspend for the already enabled device
shouldn't matter much, it's better to fix the unbalanced call.
Fixes: 9799110825 ("ALSA: usb-audio: Disable USB autosuspend properly in setup_disable_autosuspend()")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/s5hr1flh9ov.wl-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 75d95e2e39 upstream.
This use-after-free happens when a fw_priv object has been freed but
hasn't been removed from the pending list (pending_fw_head). The next
time fw_load_sysfs_fallback tries to insert into the list, it ends up
accessing the pending_list member of the previously freed fw_priv.
The root cause here is that all code paths that abort the fw load
don't delete it from the pending list. For example:
_request_firmware()
-> fw_abort_batch_reqs()
-> fw_state_aborted()
To fix this, delete the fw_priv from the list in __fw_set_state() if
the new state is DONE or ABORTED. This way, all aborts will remove
the fw_priv from the list. Accordingly, remove calls to list_del_init
that were being made before calling fw_state_(aborted|done).
Also, in fw_load_sysfs_fallback, don't add the fw_priv to the pending
list if it is already aborted. Instead, just jump out and return early.
Fixes: bcfbd3523f ("firmware: fix a double abort case with fw_load_sysfs_fallback")
Cc: stable <stable@vger.kernel.org>
Reported-by: syzbot+de271708674e2093097b@syzkaller.appspotmail.com
Tested-by: syzbot+de271708674e2093097b@syzkaller.appspotmail.com
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Anirudh Rayabharam <mail@anirudhrb.com>
Link: https://lore.kernel.org/r/20210728085107.4141-3-mail@anirudhrb.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d6434e10b upstream.
The only motivation for using -EAGAIN in commit 0542ad88fb
("firmware loader: Fix _request_firmware_load() return val for fw load
abort") was to distinguish the error from -ENOMEM, and so there is no
real reason in keeping it. -EAGAIN is typically used to tell the
userspace to try something again and in this case re-using the sysfs
loading interface cannot be retried when a timeout happens, so the
return value is also bogus.
-ETIMEDOUT is received when the wait times out and returning that
is much more telling of what the reason for the failure was. So, just
propagate that instead of returning -EAGAIN.
Suggested-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Anirudh Rayabharam <mail@anirudhrb.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210728085107.4141-2-mail@anirudhrb.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c18e9baee upstream.
The chip supports high transfer rates, but with the small default buffers
(64 bytes read), some entire blocks are regularly lost. This typically
happens at 1.5 Mbps (which is the default speed on Rockchip devices) when
used as a console to access U-Boot where the output of the "help" command
misses many lines and where "printenv" mangles the environment.
The FTDI driver doesn't suffer at all from this. One difference is that
it uses 512 bytes rx buffers and 256 bytes tx buffers. Adopting these
values completely resolved the issue, even the output of "dmesg" is
reliable. I preferred to leave the Tx value unchanged as it is not
involved in this issue, while a change could increase the risk of
triggering the same issue with other devices having too small buffers.
I verified that it backports well (and works) at least to 5.4. It's of
low importance enough to be dropped where it doesn't trivially apply
anymore.
Cc: stable@vger.kernel.org
Signed-off-by: Willy Tarreau <w@1wt.eu>
Link: https://lore.kernel.org/r/20210724152739.18726-1-w@1wt.eu
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 30fad76ce4 upstream.
rcu: INFO: rcu_preempt self-detected stall on CPU
rcu: 1-...!: (2 ticks this GP) idle=d92/1/0x4000000000000000
softirq=25390/25392 fqs=3
(t=12164 jiffies g=31645 q=43226)
rcu: rcu_preempt kthread starved for 12162 jiffies! g31645 f0x0
RCU_GP_WAIT_FQS(5) ->state=0x0 ->cpu=0
rcu: Unless rcu_preempt kthread gets sufficient CPU time,
OOM is now expected behavior.
rcu: RCU grace-period kthread stack dump:
task:rcu_preempt state:R running task
...........
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: usb_submit_urb failed: -19
The function usbtmc_interrupt() resubmits urbs when the error status
of an urb is -EPROTO. In systems using the dummy_hcd usb controller
this can result in endless interrupt loops when the usbtmc device is
disconnected from the host system.
Since host controller drivers already try to recover from transmission
errors, there is no need to resubmit the urb or try other solutions
to repair the error situation.
In case of errors the INT pipe just stops to wait for further packets.
Fixes: dbf3e7f654 ("Implement an ioctl to support the USMTMC-USB488 READ_STATUS_BYTE operation")
Cc: stable@vger.kernel.org
Reported-by: syzbot+e2eae5639e7203360018@syzkaller.appspotmail.com
Signed-off-by: Qiang.zhang <qiang.zhang@windriver.com>
Acked-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Link: https://lore.kernel.org/r/20210723004334.458930-1-qiang.zhang@windriver.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e04480920d ]
syzbot is hitting might_sleep() warning at hci_sock_dev_event() due to
calling lock_sock() with rw spinlock held [1].
It seems that history of this locking problem is a trial and error.
Commit b40df5743e ("[PATCH] bluetooth: fix socket locking in
hci_sock_dev_event()") in 2.6.21-rc4 changed bh_lock_sock() to
lock_sock() as an attempt to fix lockdep warning.
Then, commit 4ce61d1c7a ("[BLUETOOTH]: Fix locking in
hci_sock_dev_event().") in 2.6.22-rc2 changed lock_sock() to
local_bh_disable() + bh_lock_sock_nested() as an attempt to fix the
sleep in atomic context warning.
Then, commit 4b5dd696f8 ("Bluetooth: Remove local_bh_disable() from
hci_sock.c") in 3.3-rc1 removed local_bh_disable().
Then, commit e305509e67 ("Bluetooth: use correct lock to prevent UAF
of hdev object") in 5.13-rc5 again changed bh_lock_sock_nested() to
lock_sock() as an attempt to fix CVE-2021-3573.
This difficulty comes from current implementation that
hci_sock_dev_event(HCI_DEV_UNREG) is responsible for dropping all
references from sockets because hci_unregister_dev() immediately
reclaims resources as soon as returning from
hci_sock_dev_event(HCI_DEV_UNREG).
But the history suggests that hci_sock_dev_event(HCI_DEV_UNREG) was not
doing what it should do.
Therefore, instead of trying to detach sockets from device, let's accept
not detaching sockets from device at hci_sock_dev_event(HCI_DEV_UNREG),
by moving actual cleanup of resources from hci_unregister_dev() to
hci_cleanup_dev() which is called by bt_host_release() when all
references to this unregistered device (which is a kobject) are gone.
Since hci_sock_dev_event(HCI_DEV_UNREG) no longer resets
hci_pi(sk)->hdev, we need to check whether this device was unregistered
and return an error based on HCI_UNREGISTER flag. There might be subtle
behavioral difference in "monitor the hdev" functionality; please report
if you found something went wrong due to this patch.
Link: https://syzkaller.appspot.com/bug?extid=a5df189917e79d5e59c9 [1]
Reported-by: syzbot <syzbot+a5df189917e79d5e59c9@syzkaller.appspotmail.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes: e305509e67 ("Bluetooth: use correct lock to prevent UAF of hdev object")
Acked-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d75d0eff6 ]
If queue is dying while iolatency_set_limit() is in progress,
blk_get_queue() won't increment the refcount of the queue. However,
blk_put_queue() will still decrement the refcount later, which will
cause the refcout to be unbalanced.
Thus error out in such case to fix the problem.
Fixes: 8c772a9bfc ("blk-iolatency: fix IO hang due to negative inflight counter")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20210805124645.543797-1-yukuai3@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 942e560a3d ]
Smatch says:
drivers/net/ethernet/neterion/vxge/vxge-main.c:3518 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev);
drivers/net/ethernet/neterion/vxge/vxge-main.c:3518 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev);
drivers/net/ethernet/neterion/vxge/vxge-main.c:3520 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev);
drivers/net/ethernet/neterion/vxge/vxge-main.c:3520 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev);
Since vdev pointer is netdev private data accessing it after free_netdev()
call can cause use-after-free bug. Fix it by moving free_netdev() call at
the end of the function
Fixes: 6cca200362 ("vxge: cleanup probe error paths")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44712965bf ]
Smatch says:
drivers/net/ethernet/freescale/fec_main.c:3994 fec_drv_remove() error: Using fep after free_{netdev,candev}(ndev);
drivers/net/ethernet/freescale/fec_main.c:3995 fec_drv_remove() error: Using fep after free_{netdev,candev}(ndev);
Since fep pointer is netdev private data, accessing it after free_netdev()
call can cause use-after-free bug. Fix it by moving free_netdev() call at
the end of the function
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: a31eda65ba ("net: fec: fix clock count mis-match")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af35fc3735 ]
Syzbot reported uninit value pegasus_probe(). The problem was in missing
error handling.
get_interrupt_interval() internally calls read_eprom_word() which can
fail in some cases. For example: failed to receive usb control message.
These cases should be handled to prevent uninit value bug, since
read_eprom_word() will not initialize passed stack variable in case of
internal failure.
Fail log:
BUG: KMSAN: uninit-value in get_interrupt_interval drivers/net/usb/pegasus.c:746 [inline]
BUG: KMSAN: uninit-value in pegasus_probe+0x10e7/0x4080 drivers/net/usb/pegasus.c:1152
CPU: 1 PID: 825 Comm: kworker/1:1 Not tainted 5.12.0-rc6-syzkaller #0
...
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:79 [inline]
dump_stack+0x24c/0x2e0 lib/dump_stack.c:120
kmsan_report+0xfb/0x1e0 mm/kmsan/kmsan_report.c:118
__msan_warning+0x5c/0xa0 mm/kmsan/kmsan_instr.c:197
get_interrupt_interval drivers/net/usb/pegasus.c:746 [inline]
pegasus_probe+0x10e7/0x4080 drivers/net/usb/pegasus.c:1152
....
Local variable ----data.i@pegasus_probe created at:
get_interrupt_interval drivers/net/usb/pegasus.c:1151 [inline]
pegasus_probe+0xe57/0x4080 drivers/net/usb/pegasus.c:1152
get_interrupt_interval drivers/net/usb/pegasus.c:1151 [inline]
pegasus_probe+0xe57/0x4080 drivers/net/usb/pegasus.c:1152
Reported-and-tested-by: syzbot+02c9f70f3afae308464a@syzkaller.appspotmail.com
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/20210804143005.439-1-paskripkin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb653827c7 ]
Set the error code if bnx2x_alloc_fw_stats_mem() fails. The current
code returns success.
Fixes: ad5afc8936 ("bnx2x: Separate VF and PF logic")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28bbbb9875 ]
When cross compiling a MIPS kernel on a BSD based HOSTCC leads
to errors like
SYNC include/config/auto.conf.cmd - due to: .config
egrep: empty (sub)expression
UPD include/config/kernel.release
HOSTCC scripts/dtc/dtc.o - due to target missing
It turns out that egrep uses this egrep pattern:
(|MINOR_|PATCHLEVEL_)
This is not valid syntax or gives undefined results according
to POSIX 9.5.3 ERE Grammar
https://pubs.opengroup.org/onlinepubs/9699919799/basedefs/V1_chap09.html
It seems to be silently accepted by the Linux egrep implementation
while a BSD host complains.
Such patterns can be replaced by a transformation like
"(|p1|p2)" -> "(p1|p2)?"
Fixes: 48c35b2d24 ("[MIPS] There is no __GNUC_MAJOR__")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06f5553e0f ]
According to comment in qdisc_alloc(), sch->seqlock's lockdep
class key should be set to qdisc_tx_busylock, due to possible
type error, sch->busylock's lockdep class key is set to
qdisc_tx_busylock, which is duplicated because sch->busylock's
lockdep class key is already set in qdisc_alloc().
So fix it by replacing sch->busylock with sch->seqlock.
Fixes: 96009c7d50 ("sched: replace __QDISC_STATE_RUNNING bit with a spin lock")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1a58c013a ]
In case of this switch we work with 32bit registers on top of 16bit
bus. Some registers (for example access to forwarding database) have
trigger bit on the first 16bit half of request and the result +
configuration of request in the second half. Without this patch, we would
trigger database operation and overwrite result in one run.
To make it work properly, we should do the second part of transfer
before the first one is done.
So far, this rule seems to work for all registers on this switch.
Fixes: ec6698c272 ("net: dsa: add support for Atheros AR9331 built-in switch")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20210803063746.3600-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4039146777 ]
The patch fixing the returned value of ip6_skb_dst_mtu (int -> unsigned
int) was rebased between its initial review and the version applied. In
the meantime fade56410c was applied, which added a new variable (int)
used as the returned value. This lead to a mismatch between the function
prototype and the variable used as the return value.
Fixes: 40fc3054b4 ("net: ipv6: fix return value of ip6_skb_dst_mtu")
Cc: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9fdc5d85a8 ]
Pauseframe control is set to symmetric mode by default on the NFP.
Pause frames can not be configured through ethtool now, but ethtool can
report the supported mode.
Fixes: 265aeb511b ("nfp: add support for .get_link_ksettings()")
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae954bbc45 ]
In commit 58acd10092 ("sctp: update active_key for asoc when old key is
being replaced"), sctp_auth_asoc_init_active_key() is called to update
the active_key right after the old key is deleted and before the new key
is added, and it caused that the active_key could be found with the key_id.
In Ying Xu's testing, the BUG_ON in sctp_auth_asoc_init_active_key() was
triggered:
[ ] kernel BUG at net/sctp/auth.c:416!
[ ] RIP: 0010:sctp_auth_asoc_init_active_key.part.8+0xe7/0xf0 [sctp]
[ ] Call Trace:
[ ] sctp_auth_set_key+0x16d/0x1b0 [sctp]
[ ] sctp_setsockopt.part.33+0x1ba9/0x2bd0 [sctp]
[ ] __sys_setsockopt+0xd6/0x1d0
[ ] __x64_sys_setsockopt+0x20/0x30
[ ] do_syscall_64+0x5b/0x1a0
So fix it by moving the active_key update after sh_keys is added.
Fixes: 58acd10092 ("sctp: update active_key for asoc when old key is being replaced")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b87f43537 ]
The tqmx86 MFD driver was passing IRQ 0 for "no IRQ" in the past. This
causes warnings with newer kernels.
Prepare the gpio-tqmx86 driver for the fixed MFD driver by handling a
missing IRQ properly.
Fixes: b868db94a6 ("gpio: tqmx86: Add GPIO from for this IO controller")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7fe74dfd41 ]
Replace pci_enable_device() with pcim_enable_device(),
pci_disable_device() and pci_release_regions() will be
called in release automatically.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5e63c7d38 ]
The logic for discerning between KSZ8051 and KSZ87XX PHYs is incorrect
such that the that KSZ87XX switch is not identified correctly.
ksz8051_ksz8795_match_phy_device() uses the parameter ksz_phy_id
to discriminate whether it was called from ksz8051_match_phy_device()
or from ksz8795_match_phy_device() but since PHY_ID_KSZ87XX is the
same value as PHY_ID_KSZ8051, this doesn't work.
Instead use a bool to discriminate the caller.
Without this patch, the KSZ8795 switch port identifies as:
ksz8795-switch spi3.1 ade1 (uninitialized): PHY [dsa-0.1:03] driver [Generic PHY]
With the patch, it identifies correctly:
ksz8795-switch spi3.1 ade1 (uninitialized): PHY [dsa-0.1:03] driver [Micrel KSZ87XX Switch]
Fixes: 8b95599c55 ("net: phy: micrel: Discern KSZ8051 and KSZ8795 PHYs")
Signed-off-by: Steve Bennett <steveb@workware.net.au>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47c2c0c231 ]
On SJA1105P/Q/R/S and SJA1110, the L2 Lookup Table entries contain a
maskable "inner/outer tag" bit which means:
- when set to 1: match single-outer and double tagged frames
- when set to 0: match untagged and single-inner tagged frames
- when masked off: match all frames regardless of the type of tag
This driver does not make any meaningful distinction between inner tags
(matches on TPID) and outer tags (matches on TPID2). In fact, all VLAN
table entries are installed as SJA1110_VLAN_D_TAG, which means that they
match on both inner and outer tags.
So it does not make sense that we install FDB entries with the IOTAG bit
set to 1.
In VLAN-unaware mode, we set both TPID and TPID2 to 0xdadb, so the
switch will see frames as outer-tagged or double-tagged (never inner).
So the FDB entries will match if IOTAG is set to 1.
In VLAN-aware mode, we set TPID to 0x8100 and TPID2 to 0x88a8. So the
switch will see untagged and 802.1Q-tagged packets as inner-tagged, and
802.1ad-tagged packets as outer-tagged. So untagged and 802.1Q-tagged
packets will not match FDB entries if IOTAG is set to 1, but 802.1ad
tagged packets will. Strange.
To fix this, simply mask off the IOTAG bit from FDB entries, and make
them match regardless of whether the VLAN tag is inner or outer.
Fixes: 1da7382134 ("net: dsa: sja1105: Add FDB operations for P/Q/R/S series")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 589918df93 ]
Similar but not quite the same with what was done in commit b11f0a4c0c
("net: dsa: sja1105: be stateless when installing FDB entries") for
SJA1105E/T, it is desirable to drop the priv->vlan_aware check and
simply go ahead and install FDB entries in the VLAN that was given by
the bridge.
As opposed to SJA1105E/T, in SJA1105P/Q/R/S and SJA1110, the FDB is a
maskable TCAM, and we are installing VLAN-unaware FDB entries with the
VLAN ID masked off. However, such FDB entries might completely obscure
VLAN-aware entries where the VLAN ID is included in the search mask,
because the switch looks up the FDB from left to right and picks the
first entry which results in a masked match. So it depends on whether
the bridge installs first the VLAN-unaware or the VLAN-aware FDB entries.
Anyway, if we had a VLAN-unaware FDB entry towards one set of DESTPORTS
and a VLAN-aware one towards other set of DESTPORTS, the result is that
the packets in VLAN-aware mode will be forwarded towards the DESTPORTS
specified by the VLAN-unaware entry.
To solve this, simply do not use the masked matching ability of the FDB
for VLAN ID, and always match precisely on it. In VLAN-unaware mode, we
configure the switch for shared VLAN learning, so the VLAN ID will be
ignored anyway during lookup, so it is redundant to mask it off in the
TCAM.
This patch conflicts with net-next commit 0fac6aa098 ("net: dsa: sja1105:
delete the best_effort_vlan_filtering mode") which changed this line:
if (priv->vlan_state != SJA1105_VLAN_UNAWARE) {
into:
if (priv->vlan_aware) {
When merging with net-next, the lines added by this patch should take
precedence in the conflict resolution (i.e. the "if" condition should be
deleted in both cases).
Fixes: 1da7382134 ("net: dsa: sja1105: Add FDB operations for P/Q/R/S series")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c5fc159e0 ]
The procedure to add a static FDB entry in sja1105 is concurrent with
dynamic learning performed on all bridge ports and the CPU port.
The switch looks up the FDB from left to right, and also learns
dynamically from left to right, so it is possible that between the
moment when we pick up a free slot to install an FDB entry, another slot
to the left of that one becomes free due to an address ageing out, and
that other slot is then immediately used by the switch to learn
dynamically the same address as we're trying to add statically.
The result is that we succeeded to add our static FDB entry, but it is
being shadowed by a dynamic FDB entry to its left, and the switch will
behave as if our static FDB entry did not exist.
We cannot really prevent this from happening unless we make the entire
process to add a static FDB entry a huge critical section where address
learning is temporarily disabled on _all_ ports, and then re-enabled
according to the configuration done by sja1105_port_set_learning.
However, that is kind of disruptive for the operation of the network.
What we can do alternatively is to simply read back the FDB for dynamic
entries located before our newly added static one, and delete them.
This will guarantee that our static FDB entry is now operational. It
will still not guarantee that there aren't dynamic FDB entries to the
_right_ of that static FDB entry, but at least those entries will age
out by themselves since they aren't hit, and won't bother anyone.
Fixes: 291d1e72b7 ("net: dsa: sja1105: Add support for FDB and MDB management")
Fixes: 1da7382134 ("net: dsa: sja1105: Add FDB operations for P/Q/R/S series")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e11e865bf8 ]
The SJA1105 switch family leaves it up to software to decide where
within the FDB to install a static entry, and to concatenate destination
ports for already existing entries (the FDB is also used for multicast
entries), it is not as simple as just saying "please add this entry".
This means we first need to search for an existing FDB entry before
adding a new one. The driver currently manages to fool itself into
thinking that if an FDB entry already exists, there is nothing to be
done. But that FDB entry might be dynamically learned, case in which it
should be replaced with a static entry, but instead it is left alone.
This patch checks the LOCKEDS ("locked/static") bit from found FDB
entries, and lets the code "goto skip_finding_an_index;" if the FDB
entry was not static. So we also need to move the place where we set
LOCKEDS = true, to cover the new case where a dynamic FDB entry existed
but was dynamic.
Fixes: 291d1e72b7 ("net: dsa: sja1105: Add support for FDB and MDB management")
Fixes: 1da7382134 ("net: dsa: sja1105: Add FDB operations for P/Q/R/S series")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d51c5907e9 ]
GSO expects inner transport header offset to be valid when
skb->encapsulation flag is set. GSO uses this value to calculate the length
of an individual segment of a GSO packet in skb_gso_transport_seglen().
However, tcp/udp gro_complete callbacks don't update the
skb->inner_transport_header when processing an encapsulated TCP/UDP
segment. As a result a GRO skb has ->inner_transport_header set to a value
carried over from earlier skb processing.
This can have mild to tragic consequences. From miscalculating the GSO
segment length to triggering a page fault [1], when trying to read TCP/UDP
header at an address past the skb->data page.
The latter scenario leads to an oops report like so:
BUG: unable to handle page fault for address: ffff9fa7ec00d008
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 123f201067 P4D 123f201067 PUD 123f209067 PMD 0
Oops: 0000 [#1] SMP NOPTI
CPU: 44 PID: 0 Comm: swapper/44 Not tainted 5.4.53-cloudflare-2020.7.21 #1
Hardware name: HYVE EDGE-METAL-GEN10/HS-1811DLite1, BIOS V2.15 02/21/2020
RIP: 0010:skb_gso_transport_seglen+0x44/0xa0
Code: c0 41 83 e0 11 f6 87 81 00 00 00 20 74 30 0f b7 87 aa 00 00 00 0f [...]
RSP: 0018:ffffad8640bacbb8 EFLAGS: 00010202
RAX: 000000000000feda RBX: ffff9fcc8d31bc00 RCX: ffff9fa7ec00cffc
RDX: ffff9fa7ebffdec0 RSI: 000000000000feda RDI: 0000000000000122
RBP: 00000000000005c4 R08: 0000000000000001 R09: 0000000000000000
R10: ffff9fe588ae3800 R11: ffff9fe011fc92f0 R12: ffff9fcc8d31bc00
R13: ffff9fe0119d4300 R14: 00000000000005c4 R15: ffff9fba57d70900
FS: 0000000000000000(0000) GS:ffff9fe68df00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffff9fa7ec00d008 CR3: 0000003e99b1c000 CR4: 0000000000340ee0
Call Trace:
<IRQ>
skb_gso_validate_network_len+0x11/0x70
__ip_finish_output+0x109/0x1c0
ip_sublist_rcv_finish+0x57/0x70
ip_sublist_rcv+0x2aa/0x2d0
? ip_rcv_finish_core.constprop.0+0x390/0x390
ip_list_rcv+0x12b/0x14f
__netif_receive_skb_list_core+0x2a9/0x2d0
netif_receive_skb_list_internal+0x1b5/0x2e0
napi_complete_done+0x93/0x140
veth_poll+0xc0/0x19f [veth]
? mlx5e_napi_poll+0x221/0x610 [mlx5_core]
net_rx_action+0x1f8/0x790
__do_softirq+0xe1/0x2bf
irq_exit+0x8e/0xc0
do_IRQ+0x58/0xe0
common_interrupt+0xf/0xf
</IRQ>
The bug can be observed in a simple setup where we send IP/GRE/IP/TCP
packets into a netns over a veth pair. Inside the netns, packets are
forwarded to dummy device:
trafgen -> [veth A]--[veth B] -forward-> [dummy]
For veth B to GRO aggregate packets on receive, it needs to have an XDP
program attached (for example, a trivial XDP_PASS). Additionally, for UDP,
we need to enable GSO_UDP_L4 feature on the device:
ip netns exec A ethtool -K AB rx-udp-gro-forwarding on
The last component is an artificial delay to increase the chances of GRO
batching happening:
ip netns exec A tc qdisc add dev AB root \
netem delay 200us slot 5ms 10ms packets 2 bytes 64k
With such a setup in place, the bug can be observed by tracing the skb
outer and inner offsets when GSO skb is transmitted from the dummy device:
tcp:
FUNC DEV SKB_LEN NH TH ENC INH ITH GSO_SIZE GSO_TYPE
ip_finish_output dumB 2830 270 290 1 294 254 1383 (tcpv4,gre,)
^^^
udp:
FUNC DEV SKB_LEN NH TH ENC INH ITH GSO_SIZE GSO_TYPE
ip_finish_output dumB 2818 270 290 1 294 254 1383 (gre,udp_l4,)
^^^
Fix it by updating the inner transport header offset in tcp/udp
gro_complete callbacks, similar to how {inet,ipv6}_gro_complete callbacks
update the inner network header offset, when skb->encapsulation flag is
set.
[1] https://lore.kernel.org/netdev/CAKxSbF01cLpZem2GFaUaifh0S-5WYViZemTicAg7FCHOnh6kug@mail.gmail.com/
Fixes: bf296b125b ("tcp: Add GRO support")
Fixes: f993bc25e5 ("net: core: handle encapsulation offloads when computing segment lengths")
Fixes: e20cf8d3f1 ("udp: implement GRO for plain UDP sockets.")
Reported-by: Alex Forster <aforster@cloudflare.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7199ddede9 ]
Commit dea7a9fbb0 ("dmaengine: imx-dma: remove dma_slave_config
direction usage") changes the method from a "configuration when called"
to an "configuration when used". Due to this, only the cyclic DMA type
gets configured correctly, while the generic DMA type is left
non-configured.
Without this additional call, the struct imxdma_channel::word_size member
is stuck at DMA_SLAVE_BUSWIDTH_UNDEFINED and imxdma_prep_slave_sg() always
returns NULL.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Fixes: dea7a9fbb0 ("dmaengine: imx-dma: remove dma_slave_config direction usage")
Link: https://lore.kernel.org/r/20210729071821.9857-1-jbe@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15f68f027e ]
While 7e5f3155dc ("ARM: dts: stm32: Fix LED5 on STM32MP1 DHCOM PDK2")
fixed the LED0 assignment on the PDK2 board, the same commit did not
update the touchscreen IRQ line assignment, which is the same GPIO line,
shared between the LED0 output and touchscreen IRQ input. To make this
more convoluted, the same EXTI input (not the same GPIO line) is shared
between Button B which is Active-Low IRQ, and touchscreen IRQ which is
Edge-Falling IRQ, which cannot be used at the same time. In case the LCD
board with touchscreen is in use, which is the case here, LED0 must be
disabled, Button B must be polled, so the touchscreen interrupt works as
it should.
Update the touchscreen IRQ line assignment, disable LED0 and use polled
GPIO button driver for Button B, since the DT here describes baseboard
with LCD board.
Fixes: 7e5f3155dc ("ARM: dts: stm32: Fix LED5 on STM32MP1 DHCOM PDK2")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36862c1ebc ]
The LAN8710 Energy Detect Power Down (EDPD) functionality might cause
unreliable cable detection. There are multiple accounts of this in the
SMSC PHY driver patches which attempted to make EDPD reliable, however
it seems there is always some sort of corner case left. Unfortunatelly,
there is no errata documented which would confirm this to be a silicon
bug on the LAN87xx series of PHYs (LAN8700, LAN8710, LAN8720 at least).
Disable EDPD on the DHCOM SoM, just like multiple other boards already
do as well, to make the cable detection reliable.
Fixes: 34e0c7847d ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c592b46907 ]
If a vb2_queue sets q->min_buffers_needed then when the number of
queued buffers reaches q->min_buffers_needed, vb2_core_qbuf() will call
the start_streaming() callback. If start_streaming() returns an error,
then that error was just returned by vb2_core_qbuf(), but the buffer
was still queued. However, userspace expects that if VIDIOC_QBUF fails,
the buffer is returned dequeued.
So if start_streaming() fails, then remove the buffer from the queue,
thus avoiding this unwanted side-effect.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Fixes: b3379c6201 ("[media] vb2: only call start_streaming if sufficient buffers are queued")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c04243a56 ]
Media event code 3 is defined in the MMC-6 spec as follows:
"MediaRemoval: The media has been removed from the specified slot, and
the Drive is unable to access the media without user intervention. This
applies to media changers only."
This indicated that treating the condition as an EJECT_REQUEST was
appropriate. However, doing so had the unfortunate side-effect of causing
the drive tray to be physically ejected on resume. Instead treat the event
as a MEDIA_CHANGE request.
Fixes: 7dd753ca59 ("scsi: sr: Return appropriate error code when disk is ejected")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=213759
Link: https://lore.kernel.org/r/20210726114913.6760-1-limanyi@uniontech.com
Signed-off-by: Li Manyi <limanyi@uniontech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 53ca18acbe ]
The spi_imx->spi_bus_clk may be uninitialized and thus also zero in
mx51_ecspi_prepare_message(), which would lead to division by zero
in kernel. Since bitbang .setup_transfer callback which initializes
the spi_imx->spi_bus_clk is called after bitbang prepare_message
callback, iterate over all the transfers in spi_message, find the
one with lowest bus frequency, and use that bus frequency for the
delay calculation.
Note that it is not possible to move this CONFIGREG delay back into
the .setup_transfer callback, because that is invoked too late, after
the GPIO chipselects were already configured.
Fixes: 135cbd378e ("spi: imx: mx51-ecspi: Reinstate low-speed CONFIGREG delay")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210726100102.5188-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 135cbd378e ]
Since 00b80ac935 ("spi: imx: mx51-ecspi: Move some initialisation to
prepare_message hook."), the MX51_ECSPI_CONFIG write no longer happens
in prepare_transfer hook, but rather in prepare_message hook, however
the MX51_ECSPI_CONFIG delay is still left in prepare_transfer hook and
thus has no effect. This leads to low bus frequency operation problems
described in 6fd8b8503a ("spi: spi-imx: Fix out-of-order CS/SCLK
operation at low speeds") again.
Move the MX51_ECSPI_CONFIG write delay into the prepare_message hook
as well, thus reinstating the low bus frequency fix.
Fixes: 00b80ac935 ("spi: imx: mx51-ecspi: Move some initialisation to prepare_message hook.")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210703022300.296114-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d54db74ad6 ]
pm_runtime_get_sync will increment pm usage counter
even it failed. Forgetting to putting operation will
result in reference leak here. We fix it by replacing
it with pm_runtime_resume_and_get to keep usage counter
balanced.
Fixes: 48bc73ba14 ("dmaengine: stm32-dma: Add PM Runtime support")
Fixes: 05f8740a0e ("dmaengine: stm32-dma: add suspend/resume power management support")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20210607064640.121394-2-zhangqilong3@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c68ef4ad18 ]
This device tree include file describes a fixed-regulator
connecting smps7_reg output (1.8V) to some 1.8V rail and
consumers (vdds_1v8_main).
This regulator does not physically exist.
I assume it was introduced as a wrapper around smps7_reg
to provide a speaking signal name "vdds_1v8_main" as label.
This fixed-regulator without real function was not an issue
in driver code until
Commit 98e48cd928 ("regulator: core: resolve supply for boot-on/always-on regulators")
introduced a new check for regulator initialization which
makes Palmas regulator registration fail:
[ 5.407712] ldo1: supplied by vsys_cobra
[ 5.412748] ldo2: supplied by vsys_cobra
[ 5.417603] palmas-pmic 48070000.i2c:palmas@48:palmas_pmic: failed to register 48070000.i2c:palmas@48:palmas_pmic regulator
The reason is that the supply-chain of regulators is too
long and goes from ldo3 through the virtual vdds_1v8_main
regulator and then back to smps7. This adds a cross-dependency
of probing Palmas regulators and the fixed-regulator which
leads to probe deferral by the new check and is no longer
resolved.
Since we do not control what device tree files including this
one reference (either &vdds_1v8_main or &smps7_reg or both)
we keep both labels for smps7 for compatibility.
Fixes: 98e48cd928 ("regulator: core: resolve supply for boot-on/always-on regulators")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24b5b1978c ]
Enabling the framebuffer leads to a system hang. Running, as a debug
hack, the store_pan() function in drivers/video/fbdev/core/fbsysfs.c
without taking the console_lock, allows to see the crash backtrace on
the serial line.
~ # echo 0 0 > /sys/class/graphics/fb0/pan
[ 9.719414] Unhandled exception: IPSR = 00000005 LR = fffffff1
[ 9.726937] CPU: 0 PID: 49 Comm: sh Not tainted 5.13.0-rc5 #9
[ 9.733008] Hardware name: STM32 (Device Tree Support)
[ 9.738296] PC is at clk_gate_is_enabled+0x0/0x28
[ 9.743426] LR is at stm32f4_pll_div_set_rate+0xf/0x38
[ 9.748857] pc : [<0011e4be>] lr : [<0011f9e3>] psr: 0100000b
[ 9.755373] sp : 00bc7be0 ip : 00000000 fp : 001f3ac4
[ 9.760812] r10: 002610d0 r9 : 01efe920 r8 : 00540560
[ 9.766269] r7 : 02e7ddb0 r6 : 0173eed8 r5 : 00000000 r4 : 004027c0
[ 9.773081] r3 : 0011e4bf r2 : 02e7ddb0 r1 : 0173eed8 r0 : 1d3267b8
[ 9.779911] xPSR: 0100000b
[ 9.782719] CPU: 0 PID: 49 Comm: sh Not tainted 5.13.0-rc5 #9
[ 9.788791] Hardware name: STM32 (Device Tree Support)
[ 9.794120] [<0000afa1>] (unwind_backtrace) from [<0000a33f>] (show_stack+0xb/0xc)
[ 9.802421] [<0000a33f>] (show_stack) from [<0000a8df>] (__invalid_entry+0x4b/0x4c)
The `pll_num' field in the post_div_data configuration contained a wrong
value which also referenced an uninitialized hardware clock when
clk_register_pll_div() was called.
Fixes: 517633ef63 ("clk: stm32f4: Add post divisor for I2S & SAI PLLs")
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Link: https://lore.kernel.org/r/20210725160725.10788-1-dariobin@libero.it
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4511781f95 ]
The following scenario describes an echo test for
Samsung USBC Headset (AKG) with VID/PID (0x04e8/0xa051).
We first start a capture stream(USB IN transfer) in 96Khz/24bit/1ch mode.
In clock find source function, we get value 0x2 for clock selector
and 0x1 for clock source.
Kernel-4.14 behavior
Since clock source is valid so clock selector was not set again.
We pass through this function and start a playback stream(USB OUT transfer)
in 48Khz/32bit/2ch mode. This time we get value 0x1 for clock selector
and 0x1 for clock source. Finally clock id with this setting is 0x9.
Kernel-5.10 behavior
Clock selector was always set one more time even it is valid.
When we start a playback stream, we will get 0x2 for clock selector
and 0x1 for clock source. In this case clock id becomes 0xA.
This is an incorrect clock source setting and results in severe noises.
We see wrong data rate in USB IN transfer.
(From 288 bytes/ms becomes 144 bytes/ms) It should keep in 288 bytes/ms.
This earphone works fine on older kernel version load because
this is a newly-added behavior.
Fixes: d2e8f64125 ("ALSA: usb-audio: Explicitly set up the clock selector")
Signed-off-by: chihhao.chen <chihhao.chen@mediatek.com>
Link: https://lore.kernel.org/r/1627100621-19225-1-git-send-email-chihhao.chen@mediatek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee7ab3f263 ]
Some SFP modules are not detected when i2c-fast-mode is enabled even when
clock-frequency is already set to 100000. The I2C bus violates the timing
specifications when run in fast mode. So disable fast mode on Turris Mox.
Same change was already applied for uDPU (also Armada 3720 board with SFP)
in commit fe3ec631a7 ("arm64: dts: uDPU: remove i2c-fast-mode").
Fixes: 7109d817db ("arm64: dts: marvell: add DTS for Turris Mox")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 923f989291 ]
Since drivers/mmc/host/sdhci-xenon.c declares the PROBE_PREFER_ASYNCHRONOUS
probe type, it is not guaranteed whether /dev/mmcblk0 will belong to
sdhci0 or sdhci1. In turn, this will break booting by:
root=/dev/mmcblk0p1
Fix the issue by adding aliases so that the old MMC controller indices
are preserved.
Fixes: 7320915c88 ("mmc: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in v4.14")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d9e30a520 ]
The pinctrl_power_button/pinctrl_power_out each define single GPIO
pinmux, except it is exactly the other one than the matching gpio-keys
and gpio-poweroff DT nodes use for that functionality. Swap the two
GPIOs to correct this error.
Fixes: 50d29fdb76 ("ARM: dts: imx53: Add power GPIOs on M53Menlo")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20fb73911f ]
The function imx_mmdc_perf_init recently had a 3rd argument added to
it but the equivalent macro was not updated and is still the older
2 argument version. Fix this by adding in the missing 3rd argumement
mmdc_ipg_clk.
Fixes: f07ec85365 ("ARM: imx: add missing clk_disable_unprepare()")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 29f6a20c21 ]
The PHY configuration for the variant 2 is still missing the flag for
in-band signalling between PHY and MAC. Both sides - MAC and PHY - have
to match the setting. For now, Linux only supports setting the MAC side
and thus it has to match the setting the bootloader is configuring.
Enable in-band signalling to make ethernet work.
Fixes: ab43f03074 ("arm64: dts: ls1028a: sl28: add support for variant 2")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd8e83884f ]
The AR803x PHY used on this modules seems to require the reset line to
be asserted for around 10ms in order to avoid rare cases where the PHY
gets stuck in an incoherent state that prevents it to function
correctly.
The previous value of 2ms was found to be problematic on some setups,
causing intermittent issues where the PHY would be unresponsive
every once in a while on some sytems, with a low occurrence (it typically
took around 30 consecutive reboots to encounter the issue).
Bumping the delay to the 10ms makes the issue dissapear, with more than
2500 consecutive reboots performed without the issue showing-up.
Fixes: 208d7baf80 ("ARM: imx: initial SolidRun HummingBoard support")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Hervé Codina <herve.codina@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f07ec85365 ]
clock source is prepared and enabled by clk_prepare_enable()
in probe function, but no disable or unprepare in remove and
error path.
Fixes: 9454a0caff ("ARM: imx: add mmdc ipg clock operation for mmdc")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9613aa07f ]
Commit e76bdfd740 ("ARM: imx: Added perf functionality to mmdc driver")
introduced imx_mmdc_remove(), the mmdc_base need be unmapped in it if
config PERF_EVENTS is enabled.
If imx_mmdc_perf_init() fails, the mmdc_base also need be unmapped.
Fixes: e76bdfd740 ("ARM: imx: Added perf functionality to mmdc driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e71b85473 ]
U-Boot attempts to fix up the "clock-frequency" property of the "/sysclk" node:
https://elixir.bootlin.com/u-boot/v2021.04/source/arch/arm/cpu/armv8/fsl-layerscape/fdt.c#L512
but fails to do so:
## Booting kernel from Legacy Image at a1000000 ...
Image Name:
Created: 2021-06-08 10:31:38 UTC
Image Type: AArch64 Linux Kernel Image (gzip compressed)
Data Size: 15431370 Bytes = 14.7 MiB
Load Address: 80080000
Entry Point: 80080000
Verifying Checksum ... OK
## Flattened Device Tree blob at a0000000
Booting using the fdt blob at 0xa0000000
Uncompressing Kernel Image
Loading Device Tree to 00000000fbb19000, end 00000000fbb22717 ... OK
Unable to update property /sysclk:clock-frequency, err=FDT_ERR_NOTFOUND
Starting kernel ...
All Layerscape SoCs except LS1028A use "sysclk" as the node name, and
not "clock-sysclk". So change the node name of LS1028A accordingly.
Fixes: 8897f3255c ("arm64: dts: Add support for NXP LS1028A SoC")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c1a80e80c ]
Syzbot reported memory leak in xfrm_user_rcv_msg(). The
problem was is non-freed skb's frag_list.
In skb_release_all() skb_release_data() will be called only
in case of skb->head != NULL, but netlink_skb_destructor()
sets head to NULL. So, allocated frag_list skb should be
freed manualy, since consume_skb() won't take care of it
Fixes: 5106f4a8ac ("xfrm/compat: Add 32=>64-bit messages translator")
Reported-and-tested-by: syzbot+fb347cf82c73a90efcca@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ff340e24c ]
Jarkko Nikula <jarkko.nikula@bitmer.com> reported that Beagleboard
revision c2 stopped booting. Jarkko bisected the issue down to
commit 6cfcd5563b ("clocksource/drivers/timer-ti-dm: Fix suspend
and resume for am3 and am4").
Let's fix the issue by tagging system timers as reserved rather than
ignoring them. And let's not probe any interconnect target module child
devices for reserved modules.
This allows PM runtime to keep track of clocks and clockdomains for
the interconnect target module, and prevent the system timer from idling
as we already have SYSC_QUIRK_NO_IDLE and SYSC_QUIRK_NO_IDLE_ON_INIT
flags set for system timers.
Fixes: 6cfcd5563b ("clocksource/drivers/timer-ti-dm: Fix suspend and resume for am3 and am4")
Reported-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 97367c9722 upstream.
It turned out that the current implementation of the port subscription
is racy. The subscription contains two linked lists, and we have to
add to or delete from both lists. Since both connection and
disconnection procedures perform the same order for those two lists
(i.e. src list, then dest list), when a deletion happens during a
connection procedure, the src list may be deleted before the dest list
addition completes, and this may lead to a use-after-free or an Oops,
even though the access to both lists are protected via mutex.
The simple workaround for this race is to change the access order for
the disconnection, namely, dest list, then src list. This assures
that the connection has been established when disconnecting, and also
the concurrent deletion can be avoided.
Reported-and-tested-by: folkert <folkert@vanheusden.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210801182754.GP890690@belle.intranet.vanheusden.com
Link: https://lore.kernel.org/r/20210803114312.2536-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6511a8b5b7 upstream.
Revert commit c27bac0314 ("ACPICA: Fix memory leak caused by _CID
repair function") which is reported to cause a boot issue on Acer
Swift 3 (SF314-51).
Reported-by: Adrien Precigout <dev@asdrip.fr>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d5c3954b3 upstream.
Commit 3a70dd2d05 ("spi: mediatek: fix fifo rx mode") claims that
fifo RX mode was never handled, and adds the presumably missing code
to the FIFO transfer function. However, the claim that receive data
was not handled is incorrect. It was handled as part of interrupt
handling after the transfer was complete. The code added with the above
mentioned commit reads data from the receive FIFO before the transfer
is started, which is wrong. This results in an actual transfer error
on a Hayato Chromebook.
Remove the code trying to handle receive data before the transfer is
started to fix the problem.
Fixes: 3a70dd2d05 ("spi: mediatek: fix fifo rx mode")
Cc: Peter Hess <peter.hess@ph-home.de>
Cc: Frank Wunderlich <frank-w@public-files.de>
Cc: Tzung-Bi Shih <tzungbi@google.com>
Cc: Hsin-Yi Wang <hsinyi@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Hsin-Yi Wang <hsinyi@google.com>
Tested-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20210802030023.1748777-1-linux@roeck-us.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 973377ffe8 upstream
In almost all cases from test_verifier that have been changed in here, we've
had an unreachable path with a load from a register which has an invalid
address on purpose. This was basically to make sure that we never walk this
path and to have the verifier complain if it would otherwise. Change it to
match on the right error for unprivileged given we now test these paths
under speculative execution.
There's one case where we match on exact # of insns_processed. Due to the
extra path, this will of course mismatch on unprivileged. Thus, restrict the
test->insn_processed check to privileged-only.
In one other case, we result in a 'pointer comparison prohibited' error. This
is similarly due to verifying an 'invalid' branch where we end up with a value
pointer on one side of the comparison.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d7a5091351 upstream
Update various selftest error messages:
* The 'Rx tried to sub from different maps, paths, or prohibited types'
is reworked into more specific/differentiated error messages for better
guidance.
* The change into 'value -4294967168 makes map_value pointer be out of
bounds' is due to moving the mixed bounds check into the speculation
handling and thus occuring slightly later than above mentioned sanity
check.
* The change into 'math between map_value pointer and register with
unbounded min value' is similarly due to register sanity check coming
before the mixed bounds check.
* The case of 'map access: known scalar += value_ptr from different maps'
now loads fine given masks are the same from the different paths (despite
max map value size being different).
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1bad6fd52b upstream
Given we don't need to simulate the speculative domain for registers with
immediates anymore since the verifier uses direct imm-based rewrites instead
of having to mask, we can also lift a few cases that were previously rejected.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d7940911fc ]
[Why]
Vertical and horizontal borders in timings are treated as increasing the
active area - vblank and hblank actually shrink.
Our input into DML does not include these borders so it incorrectly
assumes it has more time than available for vstartup and tmdl
calculations for some modes with borders.
An example of such a timing would be 640x480@72Hz:
h_total: 832
h_border_left: 8
h_addressable: 640
h_border_right: 8
h_front_porch: 16
h_sync_width: 40
v_total: 520
v_border_top: 8
v_addressable: 480
v_border_bottom: 8
v_front_porch: 1
v_sync_width: 3
pix_clk_100hz: 315000
[How]
Include borders as part of destination vactive/hactive.
This change DCN20+ so it has wide impact, but the destination vactive
and hactive are only really used for vstartup calculation anyway.
Most modes do not have vertical or horizontal borders.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 234211b8dd ]
The metadata address is set after the trace event, so the trace is not
capturing anything useful. Rather than logging the memory address, it's
useful to know if the command carries a metadata payload, so change the
trace event to log that true/false state instead.
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47e1e233e9 ]
One of the SUSE QA tests triggered:
localhost kernel: efi: Failed to lookup EFI memory descriptor for 0x000000003dcf8000
which comes from x86's version of efi_arch_mem_reserve() trying to
reserve a memory region. Usually, that function expects
EFI_BOOT_SERVICES_DATA memory descriptors but the above case is for the
MOKvar table which is allocated in the EFI shim as runtime services.
That lead to a fix changing the allocation of that table to boot services.
However, that fix broke booting SEV guests with that shim leading to
this kernel fix
8d651ee9c7 ("x86/ioremap: Map EFI-reserved memory as encrypted for SEV")
which extended the ioremap hint to map reserved EFI boot services as
decrypted too.
However, all that wasn't needed, IMO, because that error message in
efi_arch_mem_reserve() was innocuous in this case - if the MOKvar table
is not in boot services, then it doesn't need to be reserved in the
first place because it is, well, in runtime services which *should* be
reserved anyway.
So do that reservation for the MOKvar table only if it is allocated
in boot services data. I couldn't find any requirement about where
that table should be allocated in, unlike the ESRT which allocation is
mandated to be done in boot services data by the UEFI spec.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a17ad09617 ]
In some cases skb head could be locked and entire header
data is pulled from skb. When skb_zerocopy() called in such cases,
following BUG is triggered. This patch fixes it by copying entire
skb in such cases.
This could be optimized incase this is performance bottleneck.
---8<---
kernel BUG at net/core/skbuff.c:2961!
invalid opcode: 0000 [#1] SMP PTI
CPU: 2 PID: 0 Comm: swapper/2 Tainted: G OE 5.4.0-77-generic #86-Ubuntu
Hardware name: OpenStack Foundation OpenStack Nova, BIOS 1.13.0-1ubuntu1.1 04/01/2014
RIP: 0010:skb_zerocopy+0x37a/0x3a0
RSP: 0018:ffffbcc70013ca38 EFLAGS: 00010246
Call Trace:
<IRQ>
queue_userspace_packet+0x2af/0x5e0 [openvswitch]
ovs_dp_upcall+0x3d/0x60 [openvswitch]
ovs_dp_process_packet+0x125/0x150 [openvswitch]
ovs_vport_receive+0x77/0xd0 [openvswitch]
netdev_port_receive+0x87/0x130 [openvswitch]
netdev_frame_hook+0x4b/0x60 [openvswitch]
__netif_receive_skb_core+0x2b4/0xc90
__netif_receive_skb_one_core+0x3f/0xa0
__netif_receive_skb+0x18/0x60
process_backlog+0xa9/0x160
net_rx_action+0x142/0x390
__do_softirq+0xe1/0x2d6
irq_exit+0xae/0xb0
do_IRQ+0x5a/0xf0
common_interrupt+0xf/0xf
Code that triggered BUG:
int
skb_zerocopy(struct sk_buff *to, struct sk_buff *from, int len, int hlen)
{
int i, j = 0;
int plen = 0; /* length of skb->head fragment */
int ret;
struct page *page;
unsigned int offset;
BUG_ON(!from->head_frag && !hlen);
Signed-off-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6206b7981a ]
Liajian reported a bug_on hit on a ThunderX2 arm64 server with FastLinQ
QL41000 ethernet controller:
BUG: scheduling while atomic: kworker/0:4/531/0x00000200
[qed_probe:488()]hw prepare failed
kernel BUG at mm/vmalloc.c:2355!
Internal error: Oops - BUG: 0 [#1] SMP
CPU: 0 PID: 531 Comm: kworker/0:4 Tainted: G W 5.4.0-77-generic #86-Ubuntu
pstate: 00400009 (nzcv daif +PAN -UAO)
Call trace:
vunmap+0x4c/0x50
iounmap+0x48/0x58
qed_free_pci+0x60/0x80 [qed]
qed_probe+0x35c/0x688 [qed]
__qede_probe+0x88/0x5c8 [qede]
qede_probe+0x60/0xe0 [qede]
local_pci_probe+0x48/0xa0
work_for_cpu_fn+0x24/0x38
process_one_work+0x1d0/0x468
worker_thread+0x238/0x4e0
kthread+0xf0/0x118
ret_from_fork+0x10/0x18
In this case, qed_hw_prepare() returns error due to hw/fw error, but in
theory work queue should be in process context instead of interrupt.
The root cause might be the unpaired spin_{un}lock_bh() in
_qed_mcp_cmd_and_union(), which causes botton half is disabled incorrectly.
Reported-by: Lijian Zhang <Lijian.Zhang@arm.com>
Signed-off-by: Jia He <justin.he@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6549c46af8 ]
For linear regulators, the n_voltages should be (max - min) / step + 1.
Buck voltage from 1v to 3V, per step 100mV, and vout mask is 0x1f.
If value is from 20 to 31, the voltage will all be fixed to 3V.
And LDO also, just vout range is different from 1.2v to 3v, step is the
same. If value is from 18 to 31, the voltage will also be fixed to 3v.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/20210627080418.1718127-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ecc64fab7d ]
When checking if we need to log the new name of a renamed inode, we are
checking if the inode and its parent inode have been logged before, and if
not we don't log the new name. The check however is buggy, as it directly
compares the logged_trans field of the inodes versus the ID of the current
transaction. The problem is that logged_trans is a transient field, only
stored in memory and never persisted in the inode item, so if an inode
was logged before, evicted and reloaded, its logged_trans field is set to
a value of 0, meaning the check will return false and the new name of the
renamed inode is not logged. If the old parent directory was previously
fsynced and we deleted the logged directory entries corresponding to the
old name, we end up with a log that when replayed will delete the renamed
inode.
The following example triggers the problem:
$ mkfs.btrfs -f /dev/sdc
$ mount /dev/sdc /mnt
$ mkdir /mnt/A
$ mkdir /mnt/B
$ echo -n "hello world" > /mnt/A/foo
$ sync
# Add some new file to A and fsync directory A.
$ touch /mnt/A/bar
$ xfs_io -c "fsync" /mnt/A
# Now trigger inode eviction. We are only interested in triggering
# eviction for the inode of directory A.
$ echo 2 > /proc/sys/vm/drop_caches
# Move foo from directory A to directory B.
# This deletes the directory entries for foo in A from the log, and
# does not add the new name for foo in directory B to the log, because
# logged_trans of A is 0, which is less than the current transaction ID.
$ mv /mnt/A/foo /mnt/B/foo
# Now make an fsync to anything except A, B or any file inside them,
# like for example create a file at the root directory and fsync this
# new file. This syncs the log that contains all the changes done by
# previous rename operation.
$ touch /mnt/baz
$ xfs_io -c "fsync" /mnt/baz
<power fail>
# Mount the filesystem and replay the log.
$ mount /dev/sdc /mnt
# Check the filesystem content.
$ ls -1R /mnt
/mnt/:
A
B
baz
/mnt/A:
bar
/mnt/B:
$
# File foo is gone, it's neither in A/ nor in B/.
Fix this by using the inode_logged() helper at btrfs_log_new_name(), which
safely checks if an inode was logged before in the current transaction.
A test case for fstests will follow soon.
CC: stable@vger.kernel.org # 4.14+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de53d892e5 ]
When we are doing a rename or a link operation for an inode that was logged
in the previous transaction and that transaction is still committing, we
have a time window where we incorrectly consider that the inode was logged
previously in the current transaction and therefore decide to log it to
update it in the log. The following steps give an example on how this
happens during a link operation:
1) Inode X is logged in transaction 1000, so its logged_trans field is set
to 1000;
2) Task A starts to commit transaction 1000;
3) The state of transaction 1000 is changed to TRANS_STATE_UNBLOCKED;
4) Task B starts a link operation for inode X, and as a consequence it
starts transaction 1001;
5) Task A is still committing transaction 1000, therefore the value stored
at fs_info->last_trans_committed is still 999;
6) Task B calls btrfs_log_new_name(), it reads a value of 999 from
fs_info->last_trans_committed and because the logged_trans field of
inode X has a value of 1000, the function does not return immediately,
instead it proceeds to logging the inode, which should not happen
because the inode was logged in the previous transaction (1000) and
not in the current one (1001).
This is not a functional problem, just wasted time and space logging an
inode that does not need to be logged, contributing to higher latency
for link and rename operations.
So fix this by comparing the inodes' logged_trans field with the
generation of the current transaction instead of comparing with the value
stored in fs_info->last_trans_committed.
This case is often hit when running dbench for a long enough duration, as
it does lots of rename operations.
This patch belongs to a patch set that is comprised of the following
patches:
btrfs: fix race causing unnecessary inode logging during link and rename
btrfs: fix race that results in logging old extents during a fast fsync
btrfs: fix race that causes unnecessary logging of ancestor inodes
btrfs: fix race that makes inode logging fallback to transaction commit
btrfs: fix race leading to unnecessary transaction commit when logging inode
btrfs: do not block inode logging for so long during transaction commit
Performance results are mentioned in the change log of the last patch.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3761baae90 upstream.
This reverts commit 9e31c1fe45. Ever
since that commit, we've been having issues where a hang in one client
can propagate to another. In particular, a hang in an app can propagate
to the X server which causes the whole desktop to lock up.
Error propagation along fences sound like a good idea, but as your bug
shows, surprising consequences, since propagating errors across security
boundaries is not a good thing.
What we do have is track the hangs on the ctx, and report information to
userspace using RESET_STATS. That's how arb_robustness works. Also, if my
understanding is still correct, the EIO from execbuf is when your context
is banned (because not recoverable or too many hangs). And in all these
cases it's up to userspace to figure out what is all impacted and should
be reported to the application, that's not on the kernel to guess and
automatically propagate.
What's more, we're also building more features on top of ctx error
reporting with RESET_STATS ioctl: Encrypted buffers use the same, and the
userspace fence wait also relies on that mechanism. So it is the path
going forward for reporting gpu hangs and resets to userspace.
So all together that's why I think we should just bury this idea again as
not quite the direction we want to go to, hence why I think the revert is
the right option here.
For backporters: Please note that you _must_ have a backport of
https://lore.kernel.org/dri-devel/20210602164149.391653-2-jason@jlekstrand.net/
for otherwise backporting just this patch opens up a security bug.
v2: Augment commit message. Also restore Jason's sob that I
accidentally lost.
v3: Add a note for backporters
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Reported-by: Marcin Slusarz <marcin.slusarz@intel.com>
Cc: <stable@vger.kernel.org> # v5.6+
Cc: Jason Ekstrand <jason.ekstrand@intel.com>
Cc: Marcin Slusarz <marcin.slusarz@intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/3080
Fixes: 9e31c1fe45 ("drm/i915: Propagate errors on awaiting already signaled fences")
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Jon Bloomfield <jon.bloomfield@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210714193419.1459723-3-jason@jlekstrand.net
(cherry picked from commit 93a2711cdd)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c9d9fdbc10 upstream.
This reverts 686c7c35ab ("drm/i915/gem: Asynchronous cmdparser"). The
justification for this commit in the git history was a vague comment
about getting it out from under the struct_mutex. While this may
improve perf for some workloads on Gen7 platforms where we rely on the
command parser for features such as indirect rendering, no numbers were
provided to prove such an improvement. It claims to closed two
gitlab/bugzilla issues but with no explanation whatsoever as to why or
what bug it's fixing.
Meanwhile, by moving command parsing off to an async callback, it leaves
us with a problem of what to do on error. When things were synchronous,
EXECBUFFER2 would fail with an error code if parsing failed. When
moving it to async, we needed another way to handle that error and the
solution employed was to set an error on the dma_fence and then trust
that said error gets propagated to the client eventually. Moving back
to synchronous will help us untangle the fence error propagation mess.
This also reverts most of 0edbb9ba1b ("drm/i915: Move cmd parser
pinning to execbuffer") which is a refactor of some of our allocation
paths for asynchronous parsing. Now that everything is synchronous, we
don't need it.
v2 (Daniel Vetter):
- Add stabel Cc and Fixes tag
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Cc: <stable@vger.kernel.org> # v5.6+
Fixes: 9e31c1fe45 ("drm/i915: Propagate errors on awaiting already signaled fences")
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Jon Bloomfield <jon.bloomfield@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210714193419.1459723-2-jason@jlekstrand.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0c71437dd5 upstream.
The j1939_session_deactivate() is decrementing the session ref-count and
potentially can free() the session. This would cause use-after-free
situation.
However, the code calling j1939_session_deactivate() does always hold
another reference to the session, so that it would not be free()ed in
this code path.
This patch adds a comment to make this clear and a WARN_ON, to ensure
that future changes will not violate this requirement. Further this
patch avoids dereferencing the session pointer as a precaution to avoid
use-after-free if the session is actually free()ed.
Fixes: 9d71dd0c70 ("can: add support of SAE J1939 protocol")
Link: https://lore.kernel.org/r/20210714111602.24021-1-o.rempel@pengutronix.de
Reported-by: Xiaochen Zou <xzou017@ucr.edu>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 333cf50746 upstream.
With commit c9f3401313 ("powerpc: Always enable queued spinlocks for
64s, disable for others") CONFIG_PPC_QUEUED_SPINLOCKS is always
enabled on ppc64le, external modules that use spinlock APIs are
failing.
ERROR: modpost: GPL-incompatible module XXX.ko uses GPL-only symbol 'shared_processor'
Before the above commit, modules were able to build without any
issues. Also this problem is not seen on other architectures. This
problem can be workaround if CONFIG_UNINLINE_SPIN_UNLOCK is enabled in
the config. However CONFIG_UNINLINE_SPIN_UNLOCK is not enabled by
default and only enabled in certain conditions like
CONFIG_DEBUG_SPINLOCKS is set in the kernel config.
#include <linux/module.h>
spinlock_t spLock;
static int __init spinlock_test_init(void)
{
spin_lock_init(&spLock);
spin_lock(&spLock);
spin_unlock(&spLock);
return 0;
}
static void __exit spinlock_test_exit(void)
{
printk("spinlock_test unloaded\n");
}
module_init(spinlock_test_init);
module_exit(spinlock_test_exit);
MODULE_DESCRIPTION ("spinlock_test");
MODULE_LICENSE ("non-GPL");
MODULE_AUTHOR ("Srikar Dronamraju");
Given that spin locks are one of the basic facilities for module code,
this effectively makes it impossible to build/load almost any non GPL
modules on ppc64le.
This was first reported at https://github.com/openzfs/zfs/issues/11172
Currently shared_processor is exported as GPL only symbol.
Fix this for parity with other architectures by exposing
shared_processor to non-GPL modules too.
Fixes: 14c73bd344 ("powerpc/vcpu: Assume dedicated processors as non-preempt")
Cc: stable@vger.kernel.org # v5.5+
Reported-by: marc.c.dionne@gmail.com
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210729060449.292780-1-srikar@linux.vnet.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f2a26a3cff upstream.
readpage was calculating the offset of the page incorrectly
for the case of large swapcaches.
loff_t offset = (loff_t)page->index << PAGE_SHIFT;
As pointed out by Matthew Wilcox, this needs to use
page_file_offset() to calculate the offset instead.
Pages coming from the swap cache have page->index set
to their index within the swapcache, not within the backing
file. For a sufficiently large swapcache, we could have
overlapping values of page->index within the same backing file.
Suggested by: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: <stable@vger.kernel.org> # v5.7+
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e042aa532c upstream.
In 7fedb63a83 ("bpf: Tighten speculative pointer arithmetic mask") we
narrowed the offset mask for unprivileged pointer arithmetic in order to
mitigate a corner case where in the speculative domain it is possible to
advance, for example, the map value pointer by up to value_size-1 out-of-
bounds in order to leak kernel memory via side-channel to user space.
The verifier's state pruning for scalars leaves one corner case open
where in the first verification path R_x holds an unknown scalar with an
aux->alu_limit of e.g. 7, and in a second verification path that same
register R_x, here denoted as R_x', holds an unknown scalar which has
tighter bounds and would thus satisfy range_within(R_x, R_x') as well as
tnum_in(R_x, R_x') for state pruning, yielding an aux->alu_limit of 3:
Given the second path fits the register constraints for pruning, the final
generated mask from aux->alu_limit will remain at 7. While technically
not wrong for the non-speculative domain, it would however be possible
to craft similar cases where the mask would be too wide as in 7fedb63a83.
One way to fix it is to detect the presence of unknown scalar map pointer
arithmetic and force a deeper search on unknown scalars to ensure that
we do not run into a masking mismatch.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 59089a189e upstream.
Follow-up to fe9a5ca7e3 ("bpf: Do not mark insn as seen under speculative
path verification"). The sanitize_insn_aux_data() helper does not serve a
particular purpose in today's code. The original intention for the helper
was that if function-by-function verification fails, a given program would
be cleared from temporary insn_aux_data[], and then its verification would
be re-attempted in the context of the main program a second time.
However, a failure in do_check_subprogs() will skip do_check_main() and
propagate the error to the user instead, thus such situation can never occur.
Given its interaction is not compatible to the Spectre v1 mitigation (due to
comparing aux->seen with env->pass_cnt), just remove sanitize_insn_aux_data()
to avoid future bugs in this area.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2039f26f3a ]
Spectre v4 gadgets make use of memory disambiguation, which is a set of
techniques that execute memory access instructions, that is, loads and
stores, out of program order; Intel's optimization manual, section 2.4.4.5:
A load instruction micro-op may depend on a preceding store. Many
microarchitectures block loads until all preceding store addresses are
known. The memory disambiguator predicts which loads will not depend on
any previous stores. When the disambiguator predicts that a load does
not have such a dependency, the load takes its data from the L1 data
cache. Eventually, the prediction is verified. If an actual conflict is
detected, the load and all succeeding instructions are re-executed.
af86ca4e30 ("bpf: Prevent memory disambiguation attack") tried to mitigate
this attack by sanitizing the memory locations through preemptive "fast"
(low latency) stores of zero prior to the actual "slow" (high latency) store
of a pointer value such that upon dependency misprediction the CPU then
speculatively executes the load of the pointer value and retrieves the zero
value instead of the attacker controlled scalar value previously stored at
that location, meaning, subsequent access in the speculative domain is then
redirected to the "zero page".
The sanitized preemptive store of zero prior to the actual "slow" store is
done through a simple ST instruction based on r10 (frame pointer) with
relative offset to the stack location that the verifier has been tracking
on the original used register for STX, which does not have to be r10. Thus,
there are no memory dependencies for this store, since it's only using r10
and immediate constant of zero; hence af86ca4e30 /assumed/ a low latency
operation.
However, a recent attack demonstrated that this mitigation is not sufficient
since the preemptive store of zero could also be turned into a "slow" store
and is thus bypassed as well:
[...]
// r2 = oob address (e.g. scalar)
// r7 = pointer to map value
31: (7b) *(u64 *)(r10 -16) = r2
// r9 will remain "fast" register, r10 will become "slow" register below
32: (bf) r9 = r10
// JIT maps BPF reg to x86 reg:
// r9 -> r15 (callee saved)
// r10 -> rbp
// train store forward prediction to break dependency link between both r9
// and r10 by evicting them from the predictor's LRU table.
33: (61) r0 = *(u32 *)(r7 +24576)
34: (63) *(u32 *)(r7 +29696) = r0
35: (61) r0 = *(u32 *)(r7 +24580)
36: (63) *(u32 *)(r7 +29700) = r0
37: (61) r0 = *(u32 *)(r7 +24584)
38: (63) *(u32 *)(r7 +29704) = r0
39: (61) r0 = *(u32 *)(r7 +24588)
40: (63) *(u32 *)(r7 +29708) = r0
[...]
543: (61) r0 = *(u32 *)(r7 +25596)
544: (63) *(u32 *)(r7 +30716) = r0
// prepare call to bpf_ringbuf_output() helper. the latter will cause rbp
// to spill to stack memory while r13/r14/r15 (all callee saved regs) remain
// in hardware registers. rbp becomes slow due to push/pop latency. below is
// disasm of bpf_ringbuf_output() helper for better visual context:
//
// ffffffff8117ee20: 41 54 push r12
// ffffffff8117ee22: 55 push rbp
// ffffffff8117ee23: 53 push rbx
// ffffffff8117ee24: 48 f7 c1 fc ff ff ff test rcx,0xfffffffffffffffc
// ffffffff8117ee2b: 0f 85 af 00 00 00 jne ffffffff8117eee0 <-- jump taken
// [...]
// ffffffff8117eee0: 49 c7 c4 ea ff ff ff mov r12,0xffffffffffffffea
// ffffffff8117eee7: 5b pop rbx
// ffffffff8117eee8: 5d pop rbp
// ffffffff8117eee9: 4c 89 e0 mov rax,r12
// ffffffff8117eeec: 41 5c pop r12
// ffffffff8117eeee: c3 ret
545: (18) r1 = map[id:4]
547: (bf) r2 = r7
548: (b7) r3 = 0
549: (b7) r4 = 4
550: (85) call bpf_ringbuf_output#194288
// instruction 551 inserted by verifier \
551: (7a) *(u64 *)(r10 -16) = 0 | /both/ are now slow stores here
// storing map value pointer r7 at fp-16 | since value of r10 is "slow".
552: (7b) *(u64 *)(r10 -16) = r7 /
// following "fast" read to the same memory location, but due to dependency
// misprediction it will speculatively execute before insn 551/552 completes.
553: (79) r2 = *(u64 *)(r9 -16)
// in speculative domain contains attacker controlled r2. in non-speculative
// domain this contains r7, and thus accesses r7 +0 below.
554: (71) r3 = *(u8 *)(r2 +0)
// leak r3
As can be seen, the current speculative store bypass mitigation which the
verifier inserts at line 551 is insufficient since /both/, the write of
the zero sanitation as well as the map value pointer are a high latency
instruction due to prior memory access via push/pop of r10 (rbp) in contrast
to the low latency read in line 553 as r9 (r15) which stays in hardware
registers. Thus, architecturally, fp-16 is r7, however, microarchitecturally,
fp-16 can still be r2.
Initial thoughts to address this issue was to track spilled pointer loads
from stack and enforce their load via LDX through r10 as well so that /both/
the preemptive store of zero /as well as/ the load use the /same/ register
such that a dependency is created between the store and load. However, this
option is not sufficient either since it can be bypassed as well under
speculation. An updated attack with pointer spill/fills now _all_ based on
r10 would look as follows:
[...]
// r2 = oob address (e.g. scalar)
// r7 = pointer to map value
[...]
// longer store forward prediction training sequence than before.
2062: (61) r0 = *(u32 *)(r7 +25588)
2063: (63) *(u32 *)(r7 +30708) = r0
2064: (61) r0 = *(u32 *)(r7 +25592)
2065: (63) *(u32 *)(r7 +30712) = r0
2066: (61) r0 = *(u32 *)(r7 +25596)
2067: (63) *(u32 *)(r7 +30716) = r0
// store the speculative load address (scalar) this time after the store
// forward prediction training.
2068: (7b) *(u64 *)(r10 -16) = r2
// preoccupy the CPU store port by running sequence of dummy stores.
2069: (63) *(u32 *)(r7 +29696) = r0
2070: (63) *(u32 *)(r7 +29700) = r0
2071: (63) *(u32 *)(r7 +29704) = r0
2072: (63) *(u32 *)(r7 +29708) = r0
2073: (63) *(u32 *)(r7 +29712) = r0
2074: (63) *(u32 *)(r7 +29716) = r0
2075: (63) *(u32 *)(r7 +29720) = r0
2076: (63) *(u32 *)(r7 +29724) = r0
2077: (63) *(u32 *)(r7 +29728) = r0
2078: (63) *(u32 *)(r7 +29732) = r0
2079: (63) *(u32 *)(r7 +29736) = r0
2080: (63) *(u32 *)(r7 +29740) = r0
2081: (63) *(u32 *)(r7 +29744) = r0
2082: (63) *(u32 *)(r7 +29748) = r0
2083: (63) *(u32 *)(r7 +29752) = r0
2084: (63) *(u32 *)(r7 +29756) = r0
2085: (63) *(u32 *)(r7 +29760) = r0
2086: (63) *(u32 *)(r7 +29764) = r0
2087: (63) *(u32 *)(r7 +29768) = r0
2088: (63) *(u32 *)(r7 +29772) = r0
2089: (63) *(u32 *)(r7 +29776) = r0
2090: (63) *(u32 *)(r7 +29780) = r0
2091: (63) *(u32 *)(r7 +29784) = r0
2092: (63) *(u32 *)(r7 +29788) = r0
2093: (63) *(u32 *)(r7 +29792) = r0
2094: (63) *(u32 *)(r7 +29796) = r0
2095: (63) *(u32 *)(r7 +29800) = r0
2096: (63) *(u32 *)(r7 +29804) = r0
2097: (63) *(u32 *)(r7 +29808) = r0
2098: (63) *(u32 *)(r7 +29812) = r0
// overwrite scalar with dummy pointer; same as before, also including the
// sanitation store with 0 from the current mitigation by the verifier.
2099: (7a) *(u64 *)(r10 -16) = 0 | /both/ are now slow stores here
2100: (7b) *(u64 *)(r10 -16) = r7 | since store unit is still busy.
// load from stack intended to bypass stores.
2101: (79) r2 = *(u64 *)(r10 -16)
2102: (71) r3 = *(u8 *)(r2 +0)
// leak r3
[...]
Looking at the CPU microarchitecture, the scheduler might issue loads (such
as seen in line 2101) before stores (line 2099,2100) because the load execution
units become available while the store execution unit is still busy with the
sequence of dummy stores (line 2069-2098). And so the load may use the prior
stored scalar from r2 at address r10 -16 for speculation. The updated attack
may work less reliable on CPU microarchitectures where loads and stores share
execution resources.
This concludes that the sanitizing with zero stores from af86ca4e30 ("bpf:
Prevent memory disambiguation attack") is insufficient. Moreover, the detection
of stack reuse from af86ca4e30 where previously data (STACK_MISC) has been
written to a given stack slot where a pointer value is now to be stored does
not have sufficient coverage as precondition for the mitigation either; for
several reasons outlined as follows:
1) Stack content from prior program runs could still be preserved and is
therefore not "random", best example is to split a speculative store
bypass attack between tail calls, program A would prepare and store the
oob address at a given stack slot and then tail call into program B which
does the "slow" store of a pointer to the stack with subsequent "fast"
read. From program B PoV such stack slot type is STACK_INVALID, and
therefore also must be subject to mitigation.
2) The STACK_SPILL must not be coupled to register_is_const(&stack->spilled_ptr)
condition, for example, the previous content of that memory location could
also be a pointer to map or map value. Without the fix, a speculative
store bypass is not mitigated in such precondition and can then lead to
a type confusion in the speculative domain leaking kernel memory near
these pointer types.
While brainstorming on various alternative mitigation possibilities, we also
stumbled upon a retrospective from Chrome developers [0]:
[...] For variant 4, we implemented a mitigation to zero the unused memory
of the heap prior to allocation, which cost about 1% when done concurrently
and 4% for scavenging. Variant 4 defeats everything we could think of. We
explored more mitigations for variant 4 but the threat proved to be more
pervasive and dangerous than we anticipated. For example, stack slots used
by the register allocator in the optimizing compiler could be subject to
type confusion, leading to pointer crafting. Mitigating type confusion for
stack slots alone would have required a complete redesign of the backend of
the optimizing compiler, perhaps man years of work, without a guarantee of
completeness. [...]
From BPF side, the problem space is reduced, however, options are rather
limited. One idea that has been explored was to xor-obfuscate pointer spills
to the BPF stack:
[...]
// preoccupy the CPU store port by running sequence of dummy stores.
[...]
2106: (63) *(u32 *)(r7 +29796) = r0
2107: (63) *(u32 *)(r7 +29800) = r0
2108: (63) *(u32 *)(r7 +29804) = r0
2109: (63) *(u32 *)(r7 +29808) = r0
2110: (63) *(u32 *)(r7 +29812) = r0
// overwrite scalar with dummy pointer; xored with random 'secret' value
// of 943576462 before store ...
2111: (b4) w11 = 943576462
2112: (af) r11 ^= r7
2113: (7b) *(u64 *)(r10 -16) = r11
2114: (79) r11 = *(u64 *)(r10 -16)
2115: (b4) w2 = 943576462
2116: (af) r2 ^= r11
// ... and restored with the same 'secret' value with the help of AX reg.
2117: (71) r3 = *(u8 *)(r2 +0)
[...]
While the above would not prevent speculation, it would make data leakage
infeasible by directing it to random locations. In order to be effective
and prevent type confusion under speculation, such random secret would have
to be regenerated for each store. The additional complexity involved for a
tracking mechanism that prevents jumps such that restoring spilled pointers
would not get corrupted is not worth the gain for unprivileged. Hence, the
fix in here eventually opted for emitting a non-public BPF_ST | BPF_NOSPEC
instruction which the x86 JIT translates into a lfence opcode. Inserting the
latter in between the store and load instruction is one of the mitigations
options [1]. The x86 instruction manual notes:
[...] An LFENCE that follows an instruction that stores to memory might
complete before the data being stored have become globally visible. [...]
The latter meaning that the preceding store instruction finished execution
and the store is at minimum guaranteed to be in the CPU's store queue, but
it's not guaranteed to be in that CPU's L1 cache at that point (globally
visible). The latter would only be guaranteed via sfence. So the load which
is guaranteed to execute after the lfence for that local CPU would have to
rely on store-to-load forwarding. [2], in section 2.3 on store buffers says:
[...] For every store operation that is added to the ROB, an entry is
allocated in the store buffer. This entry requires both the virtual and
physical address of the target. Only if there is no free entry in the store
buffer, the frontend stalls until there is an empty slot available in the
store buffer again. Otherwise, the CPU can immediately continue adding
subsequent instructions to the ROB and execute them out of order. On Intel
CPUs, the store buffer has up to 56 entries. [...]
One small upside on the fix is that it lifts constraints from af86ca4e30
where the sanitize_stack_off relative to r10 must be the same when coming
from different paths. The BPF_ST | BPF_NOSPEC gets emitted after a BPF_STX
or BPF_ST instruction. This happens either when we store a pointer or data
value to the BPF stack for the first time, or upon later pointer spills.
The former needs to be enforced since otherwise stale stack data could be
leaked under speculation as outlined earlier. For non-x86 JITs the BPF_ST |
BPF_NOSPEC mapping is currently optimized away, but others could emit a
speculation barrier as well if necessary. For real-world unprivileged
programs e.g. generated by LLVM, pointer spill/fill is only generated upon
register pressure and LLVM only tries to do that for pointers which are not
used often. The program main impact will be the initial BPF_ST | BPF_NOSPEC
sanitation for the STACK_INVALID case when the first write to a stack slot
occurs e.g. upon map lookup. In future we might refine ways to mitigate
the latter cost.
[0] https://arxiv.org/pdf/1902.05178.pdf
[1] https://msrc-blog.microsoft.com/2018/05/21/analysis-and-mitigation-of-speculative-store-bypass-cve-2018-3639/
[2] https://arxiv.org/pdf/1905.05725.pdf
Fixes: af86ca4e30 ("bpf: Prevent memory disambiguation attack")
Fixes: f7cf25b202 ("bpf: track spill/fill of constants")
Co-developed-by: Piotr Krysiuk <piotras@gmail.com>
Co-developed-by: Benedict Schlueter <benedict.schlueter@rub.de>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Piotr Krysiuk <piotras@gmail.com>
Signed-off-by: Benedict Schlueter <benedict.schlueter@rub.de>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5e81d1117 ]
In case of JITs, each of the JIT backends compiles the BPF nospec instruction
/either/ to a machine instruction which emits a speculation barrier /or/ to
/no/ machine instruction in case the underlying architecture is not affected
by Speculative Store Bypass or has different mitigations in place already.
This covers both x86 and (implicitly) arm64: In case of x86, we use 'lfence'
instruction for mitigation. In case of arm64, we rely on the firmware mitigation
as controlled via the ssbd kernel parameter. Whenever the mitigation is enabled,
it works for all of the kernel code with no need to provide any additional
instructions here (hence only comment in arm64 JIT). Other archs can follow
as needed. The BPF nospec instruction is specifically targeting Spectre v4
since i) we don't use a serialization barrier for the Spectre v1 case, and
ii) mitigation instructions for v1 and v4 might be different on some archs.
The BPF nospec is required for a future commit, where the BPF verifier does
annotate intermediate BPF programs with speculation barriers.
Co-developed-by: Piotr Krysiuk <piotras@gmail.com>
Co-developed-by: Benedict Schlueter <benedict.schlueter@rub.de>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Piotr Krysiuk <piotras@gmail.com>
Signed-off-by: Benedict Schlueter <benedict.schlueter@rub.de>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89fb62fde3 ]
Replace pci_enable_device() with pcim_enable_device(),
pci_disable_device() and pci_release_regions() will be
called in release automatically.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 76a16be07b ]
Replace pci_enable_device() with pcim_enable_device(),
pci_disable_device() and pci_release_regions() will be
called in release automatically.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1c2f6312c ]
The result of __dev_get_by_index() is not checked for NULL and then gets
dereferenced immediately.
Also, __dev_get_by_index() must be called while holding either RTNL lock
or @dev_base_lock, which isn't satisfied by mlx5e_hairpin_get_mdev() or
its callers. This makes the underlying hlist_for_each_entry() loop not
safe, and can have adverse effects in itself.
Fix by using dev_get_by_index() and handling nullptr return value when
ifindex device is not found. Update mlx5e_hairpin_get_mdev() callers to
check for possible PTR_ERR() result.
Fixes: 77ab67b7f0 ("net/mlx5e: Basic setup of hairpin object")
Addresses-Coverity: ("Dereference null return value")
Signed-off-by: Dima Chumak <dchumak@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b54874ef1 ]
Fix a bug when flow table is created in priority that already
has other flow tables as shown in the below diagram.
If the new flow table (FT-B) has the lowest level in the priority,
we need to connect the flow tables from the previous priority (p0)
to this new table. In addition when this flow table is destroyed
(FT-B), we need to connect the flow tables from the previous
priority (p0) to the next level flow table (FT-C) in the same
priority of the destroyed table (if exists).
---------
|root_ns|
---------
|
--------------------------------
| | |
---------- ---------- ---------
|p(prio)-x| | p-y | | p-n |
---------- ---------- ---------
| |
---------------- ------------------
|ns(e.g bypass)| |ns(e.g. kernel) |
---------------- ------------------
| | |
------- ------ ----
| p0 | | p1 | |p2|
------- ------ ----
| | \
-------- ------- ------
| FT-A | |FT-B | |FT-C|
-------- ------- ------
Fixes: f90edfd279 ("net/mlx5_core: Connect flow tables")
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7c9d2102c ]
Syzbot reported skb_over_panic() in llc_pdu_init_as_xid_cmd(). The
problem was in wrong LCC header manipulations.
Syzbot's reproducer tries to send XID packet. llc_ui_sendmsg() is
doing following steps:
1. skb allocation with size = len + header size
len is passed from userpace and header size
is 3 since addr->sllc_xid is set.
2. skb_reserve() for header_len = 3
3. filling all other space with memcpy_from_msg()
Ok, at this moment we have fully loaded skb, only headers needs to be
filled.
Then code comes to llc_sap_action_send_xid_c(). This function pushes 3
bytes for LLC PDU header and initializes it. Then comes
llc_pdu_init_as_xid_cmd(). It initalizes next 3 bytes *AFTER* LLC PDU
header and call skb_push(skb, 3). This looks wrong for 2 reasons:
1. Bytes rigth after LLC header are user data, so this function
was overwriting payload.
2. skb_push(skb, 3) call can cause skb_over_panic() since
all free space was filled in llc_ui_sendmsg(). (This can
happen is user passed 686 len: 686 + 14 (eth header) + 3 (LLC
header) = 703. SKB_DATA_ALIGN(703) = 704)
So, in this patch I added 2 new private constansts: LLC_PDU_TYPE_U_XID
and LLC_PDU_LEN_U_XID. LLC_PDU_LEN_U_XID is used to correctly reserve
header size to handle LLC + XID case. LLC_PDU_TYPE_U_XID is used by
llc_pdu_header_init() function to push 6 bytes instead of 3. And finally
I removed skb_push() call from llc_pdu_init_as_xid_cmd().
This changes should not affect other parts of LLC, since after
all steps we just transmit buffer.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-and-tested-by: syzbot+5e5a981ad7cc54c4b2b4@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e4960b3d6 ]
The error code is missing in this code scenario, add the error code
'-EINVAL' to the return value 'err'.
Eliminate the follow smatch warning:
drivers/net/ethernet/mellanox/mlx4/main.c:3538 mlx4_load_one() warn:
missing error code 'err'.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Fixes: 7ae0e400cd ("net/mlx4_core: Flexible (asymmetric) allocation of EQs and MSI-X vectors for PF/VFs")
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69f0aeb13b ]
In the existing code while changing the number of TX/RX
queues using ethtool the PF/VF interface resources are
freed and reallocated (otx2_stop and otx2_open is called)
if the device is in running state. If any resource allocation
fails in otx2_open, driver free already allocated resources
and return. But again, when the number of queues changes
as the device state still running oxt2_stop is called.
In which we try to free already freed resources leading
to driver crash.
This patch fixes the issue by setting the INTF_DOWN flag on
error and free the resources in otx2_stop only if the flag is
not set.
Fixes: 50fe6c02e5 ("octeontx2-pf: Register and handle link notifications")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <Sunil.Goutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3cf4375a09 ]
One skb's skb_shinfo frags are not writable, and they can be shared with
other skbs' like by pskb_copy(). To write the frags may cause other skb's
data crash.
So before doing en/decryption, skb_cow_data() should always be called for
a cloned or nonlinear skb if req dst is using the same sg as req src.
While at it, the likely branch can be removed, as it will be covered
by skb_cow_data().
Note that esp_input() has the same issue, and I will fix it in another
patch. tipc_aead_encrypt() doesn't have this issue, as it only processes
linear data in the unlikely branch.
Fixes: fc1b6d6de2 ("tipc: introduce TIPC encryption & authentication")
Reported-by: Shuang Li <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f07f9815b7 ]
Be sure to count the csum_none cases when csum offload is
enabled.
Fixes: 0f3154e6bc ("ionic: Add Tx and Rx handling")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 76ed8a4a00 ]
We need to count the correct Tx and/or Rx packets for dynamic
interrupt moderation, depending on which we're processing on
the queue interrupt.
Fixes: 04a834592b ("ionic: dynamic interrupt moderation")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6ff85e0a2 ]
Move the interrupt coalesce value update out of the napi
thread and into the dim_work thread and set it only when it
has actually changed.
Fixes: 04a834592b ("ionic: dynamic interrupt moderation")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 52f3456a96 ]
Syzbot reported memory leak in qrtr. The problem was in unputted
struct sock. qrtr_local_enqueue() function calls qrtr_port_lookup()
which takes sock reference if port was found. Then there is the following
check:
if (!ipc || &ipc->sk == skb->sk) {
...
return -ENODEV;
}
Since we should drop the reference before returning from this function and
ipc can be non-NULL inside this if, we should add qrtr_port_put() inside
this if.
The similar corner case is in qrtr_endpoint_post() as Manivannan
reported. In case of sock_queue_rcv_skb() failure we need to put
port reference to avoid leaking struct sock pointer.
Fixes: e04df98adf ("net: qrtr: Remove receive worker")
Fixes: bdabad3e36 ("net: Add Qualcomm IPC router")
Reported-and-tested-by: syzbot+35a511c72ea7356cdcf3@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 227adfb2b1 ]
In cases where the header straight after the tunnel header was
another ethernet header (TEB), instead of the network header,
the ECN decapsulation code would treat the ethernet header as if
it was an IP header, resulting in mishandling and possible
wrong drops or corruption of the IP header.
In this case, ECT(1) is sent, so IP_ECN_decapsulate tries to copy it to the
inner IPv4 header, and correct its checksum.
The offset of the ECT bits in an IPv4 header corresponds to the
lower 2 bits of the second octet of the destination MAC address
in the ethernet header.
The IPv4 checksum corresponds to end of the source address.
In order to reproduce:
$ ip netns add A
$ ip netns add B
$ ip -n A link add _v0 type veth peer name _v1 netns B
$ ip -n A link set _v0 up
$ ip -n A addr add dev _v0 10.254.3.1/24
$ ip -n A route add default dev _v0 scope global
$ ip -n B link set _v1 up
$ ip -n B addr add dev _v1 10.254.1.6/24
$ ip -n B route add default dev _v1 scope global
$ ip -n B link add gre1 type gretap local 10.254.1.6 remote 10.254.3.1 key 0x49000000
$ ip -n B link set gre1 up
# Now send an IPv4/GRE/Eth/IPv4 frame where the outer header has ECT(1),
# and the inner header has no ECT bits set:
$ cat send_pkt.py
#!/usr/bin/env python3
from scapy.all import *
pkt = IP(b'E\x01\x00\xa7\x00\x00\x00\x00@/`%\n\xfe\x03\x01\n\xfe\x01\x06 \x00eXI\x00'
b'\x00\x00\x18\xbe\x92\xa0\xee&\x18\xb0\x92\xa0l&\x08\x00E\x00\x00}\x8b\x85'
b'@\x00\x01\x01\xe4\xf2\x82\x82\x82\x01\x82\x82\x82\x02\x08\x00d\x11\xa6\xeb'
b'3\x1e\x1e\\xf3\\xf7`\x00\x00\x00\x00ZN\x00\x00\x00\x00\x00\x00\x10\x11\x12'
b'\x13\x14\x15\x16\x17\x18\x19\x1a\x1b\x1c\x1d\x1e\x1f !"#$%&\'()*+,-./01234'
b'56789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ')
send(pkt)
$ sudo ip netns exec B tcpdump -neqlllvi gre1 icmp & ; sleep 1
$ sudo ip netns exec A python3 send_pkt.py
In the original packet, the source/destinatio MAC addresses are
dst=18:be:92:a0:ee:26 src=18:b0:92:a0:6c:26
In the received packet, they are
dst=18:bd:92:a0:ee:26 src=18:b0:92:a0:6c:27
Thanks to Lahav Schlesinger <lschlesinger@drivenets.com> and Isaac Garzon <isaac@speed.io>
for helping me pinpoint the origin.
Fixes: b723748750 ("tunnel: Propagate ECT(1) when decapsulating as recommended by RFC6040")
Cc: David S. Miller <davem@davemloft.net>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: David Ahern <dsahern@kernel.org>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Gilad Naaman <gnaaman@drivenets.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d237a7f117 ]
The release_sock() is blocking function, it would change the state
after sleeping. In order to evaluate the stated condition outside
the socket lock context, switch to use wait_woken() instead.
Fixes: 6398e23cdb ("tipc: standardize accept routine")
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8dd60de19 ]
For implicit-connect, when it's either SYN- or SYN+, an ACK should
be sent back to the client immediately. It's not appropriate for
the client to enter established state only after receiving data
from the server.
On client side, after the SYN is sent out, tipc_wait_for_connect()
should be called to wait for the ACK if timeout is set.
This patch also restricts __tipc_sendstream() to call __sendmsg()
only when it's in TIPC_OPEN state, so that the client can program
in a single loop doing both connecting and data sending like:
for (...)
sendmsg(dest, buf);
This makes the implicit-connect more implicit.
Fixes: b97bf3fd8f ("[TIPC] Initial merge")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89ec1f0886 ]
In SW DCB mode the packets sent receive incorrect UP tags. They are
constructed correctly and put into tx_ring, but UP is later remapped by
HW on the basis of TCTUPR register contents according to Tx queue
selected, and BW used is consistent with the new UP values. This is
caused by Tx queue selection in kernel not taking into account DCB
configuration. This patch fixes the issue by implementing the
ndo_select_queue NDO callback.
Fixes: fd0a05ce74 ("i40e: transmit, receive, and NAPI")
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Imam Hassan Reza Biswas <imam.hassan.reza.biswas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71d6fdba4b ]
Make warning meaningful for the user.
Previously the trace:
"Starting FW LLDP agent failed: error: I40E_ERR_ADMIN_QUEUE_ERROR, I40E_AQ_RC_EAGAIN"
was produced when user tried to start Firmware LLDP agent,
just after it was stopped with sequence:
ethtool --set-priv-flags <dev> disable-fw-lldp on
ethtool --set-priv-flags <dev> disable-fw-lldp off
(without any delay between the commands)
At that point the firmware is still processing stop command, the behavior
is expected.
Fixes: c1041d0704 ("i40e: Missing response checks in driver when starting/stopping FW LLDP")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Imam Hassan Reza Biswas <imam.hassan.reza.biswas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65662a8dcd ]
Correct the message flow between driver and firmware when disabling
queues.
Previously in case of PF reset (due to required reinit after reconfig),
the error like: "VSI seid 397 Tx ring 60 disable timeout" could show up
occasionally. The error was not a real issue of hardware or firmware,
it was caused by wrong sequence of messages invoked by the driver.
Fixes: 41c445ff0f ("i40e: main driver core")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30a56a2b88 ]
In case the entry is evicted via garbage collection there is
delay between the timeout value and the eviction event.
This adjusts the stop value based on how much time has passed.
Fixes: b87a2f9199 ("netfilter: conntrack: add gc worker to remove timed-out entries")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6371c76e2 ]
We got the following UBSAN report on one of our testing machines:
================================================================================
UBSAN: array-index-out-of-bounds in kernel/bpf/syscall.c:2389:24
index 6 is out of range for type 'char *[6]'
CPU: 43 PID: 930921 Comm: systemd-coredum Tainted: G O 5.10.48-cloudflare-kasan-2021.7.0 #1
Hardware name: <snip>
Call Trace:
dump_stack+0x7d/0xa3
ubsan_epilogue+0x5/0x40
__ubsan_handle_out_of_bounds.cold+0x43/0x48
? seq_printf+0x17d/0x250
bpf_link_show_fdinfo+0x329/0x380
? bpf_map_value_size+0xe0/0xe0
? put_files_struct+0x20/0x2d0
? __kasan_kmalloc.constprop.0+0xc2/0xd0
seq_show+0x3f7/0x540
seq_read_iter+0x3f8/0x1040
seq_read+0x329/0x500
? seq_read_iter+0x1040/0x1040
? __fsnotify_parent+0x80/0x820
? __fsnotify_update_child_dentry_flags+0x380/0x380
vfs_read+0x123/0x460
ksys_read+0xed/0x1c0
? __x64_sys_pwrite64+0x1f0/0x1f0
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xa9
<snip>
================================================================================
================================================================================
UBSAN: object-size-mismatch in kernel/bpf/syscall.c:2384:2
From the report, we can infer that some array access in bpf_link_show_fdinfo at index 6
is out of bounds. The obvious candidate is bpf_link_type_strs[BPF_LINK_TYPE_XDP] with
BPF_LINK_TYPE_XDP == 6. It turns out that BPF_LINK_TYPE_XDP is missing from bpf_types.h
and therefore doesn't have an entry in bpf_link_type_strs:
pos: 0
flags: 02000000
mnt_id: 13
link_type: (null)
link_id: 4
prog_tag: bcf7977d3b93787c
prog_id: 4
ifindex: 1
Fixes: aa8d3a716b ("bpf, xdp: Add bpf_link-based XDP attachment API")
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210719085134.43325-2-lmb@cloudflare.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f9a5c358c8 upstream.
When we exceed the limit of BSS entries, this function will free the
new entry, however, at this time, it is the last door to access the
inputed ies, so these ies will be unreferenced objects and cause memory
leak.
Therefore we should free its ies before deallocating the new entry, beside
of dropping it from hidden_list.
Signed-off-by: Nguyen Dinh Phi <phind.uet@gmail.com>
Link: https://lore.kernel.org/r/20210628132334.851095-1-phind.uet@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e7b30d24a upstream.
There is a use after free memory corruption during module exit:
- nfcsim_exit()
- nfcsim_device_free(dev0)
- nfc_digital_unregister_device()
This iterates over command queue and frees all commands,
- dev->up = false
- nfcsim_link_shutdown()
- nfcsim_link_recv_wake()
This wakes the sleeping thread nfcsim_link_recv_skb().
- nfcsim_link_recv_skb()
Wake from wait_event_interruptible_timeout(),
call directly the deb->cb callback even though (dev->up == false),
- digital_send_cmd_complete()
Dereference of "struct digital_cmd" cmd which was freed earlier by
nfc_digital_unregister_device().
This causes memory corruption shortly after (with unrelated stack
trace):
nfc nfc0: NFC: nfcsim_recv_wq: Device is down
llcp: nfc_llcp_recv: err -19
nfc nfc1: NFC: nfcsim_recv_wq: Device is down
BUG: unable to handle page fault for address: ffffffffffffffed
Call Trace:
fsnotify+0x54b/0x5c0
__fsnotify_parent+0x1fe/0x300
? vfs_write+0x27c/0x390
vfs_write+0x27c/0x390
ksys_write+0x63/0xe0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
KASAN report:
BUG: KASAN: use-after-free in digital_send_cmd_complete+0x16/0x50
Write of size 8 at addr ffff88800a05f720 by task kworker/0:2/71
Workqueue: events nfcsim_recv_wq [nfcsim]
Call Trace:
dump_stack_lvl+0x45/0x59
print_address_description.constprop.0+0x21/0x140
? digital_send_cmd_complete+0x16/0x50
? digital_send_cmd_complete+0x16/0x50
kasan_report.cold+0x7f/0x11b
? digital_send_cmd_complete+0x16/0x50
? digital_dep_link_down+0x60/0x60
digital_send_cmd_complete+0x16/0x50
nfcsim_recv_wq+0x38f/0x3d5 [nfcsim]
? nfcsim_in_send_cmd+0x4a/0x4a [nfcsim]
? lock_is_held_type+0x98/0x110
? finish_wait+0x110/0x110
? rcu_read_lock_sched_held+0x9c/0xd0
? rcu_read_lock_bh_held+0xb0/0xb0
? lockdep_hardirqs_on_prepare+0x12e/0x1f0
This flow of calling digital_send_cmd_complete() callback on driver exit
is specific to nfcsim which implements reading and sending work queues.
Since the NFC digital device was unregistered, the callback should not
be called.
Fixes: 204bddcb50 ("NFC: nfcsim: Make use of the Digital layer")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ab189cf3a upstream.
iocg_wake_fn() open-codes wait_queue_entry removal and wakeup because it
wants the wq_entry to be always removed whether it ended up waking the
task or not. finish_wait() tests whether wq_entry needs removal without
grabbing the wait_queue lock and expects the waker to use
list_del_init_careful() after all waking operations are complete, which
iocg_wake_fn() didn't do. The operation order was wrong and the regular
list_del_init() was used.
The result is that if a waiter wakes up racing the waker, it can free pop
the wq_entry off stack before the waker is still looking at it, which can
lead to a backtrace like the following.
[7312084.588951] general protection fault, probably for non-canonical address 0x586bf4005b2b88: 0000 [#1] SMP
...
[7312084.647079] RIP: 0010:queued_spin_lock_slowpath+0x171/0x1b0
...
[7312084.858314] Call Trace:
[7312084.863548] _raw_spin_lock_irqsave+0x22/0x30
[7312084.872605] try_to_wake_up+0x4c/0x4f0
[7312084.880444] iocg_wake_fn+0x71/0x80
[7312084.887763] __wake_up_common+0x71/0x140
[7312084.895951] iocg_kick_waitq+0xe8/0x2b0
[7312084.903964] ioc_rqos_throttle+0x275/0x650
[7312084.922423] __rq_qos_throttle+0x20/0x30
[7312084.930608] blk_mq_make_request+0x120/0x650
[7312084.939490] generic_make_request+0xca/0x310
[7312084.957600] submit_bio+0x173/0x200
[7312084.981806] swap_readpage+0x15c/0x240
[7312084.989646] read_swap_cache_async+0x58/0x60
[7312084.998527] swap_cluster_readahead+0x201/0x320
[7312085.023432] swapin_readahead+0x2df/0x450
[7312085.040672] do_swap_page+0x52f/0x820
[7312085.058259] handle_mm_fault+0xa16/0x1420
[7312085.066620] do_page_fault+0x2c6/0x5c0
[7312085.074459] page_fault+0x2f/0x40
Fix it by switching to list_del_init_careful() and putting it at the end.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Rik van Riel <riel@surriel.com>
Fixes: 7caa47151a ("blkcg: implement blk-iocost")
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d47255d3f8 upstream.
This reverts commit 4192f7b576.
It is not true (as stated in the reverted commit changelog) that we never
unmap the BAR on failure; it actually does happen properly on
amdgpu_driver_load_kms() -> amdgpu_driver_unload_kms() ->
amdgpu_device_fini() error path.
What's worse, this commit actually completely breaks resource freeing on
probe failure (like e.g. failure to load microcode), as
amdgpu_driver_unload_kms() notices adev->rmmio being NULL and bails too
early, leaving all the resources that'd normally be freed in
amdgpu_acpi_fini() and amdgpu_device_fini() still hanging around, leading
to all sorts of oopses when someone tries to, for example, access the
sysfs and procfs resources which are still around while the driver is
gone.
Fixes: 4192f7b576 ("drm/amdgpu: unmap register bar on device init failure")
Reported-by: Vojtech Pavlik <vojtech@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6aade587d3 upstream.
In case when psp_init_asd_microcode() fails to load ASD microcode file,
psp_v12_0_init_microcode() tries to print the firmware filename that
failed to load before bailing out.
This is wrong because:
- the firmware filename it would want it print is an incorrect one as
psp_init_asd_microcode() and psp_v12_0_init_microcode() are loading
different filenames
- it tries to print fw_name, but that's not yet been initialized by that
time, so it prints random stack contents, e.g.
amdgpu 0000:04:00.0: Direct firmware load for amdgpu/renoir_asd.bin failed with error -2
amdgpu 0000:04:00.0: amdgpu: fail to initialize asd microcode
amdgpu 0000:04:00.0: amdgpu: psp v12.0: Failed to load firmware "\xfeTO\x8e\xff\xff"
Fix that by bailing out immediately, instead of priting the bogus error
message.
Reported-by: Vojtech Pavlik <vojtech@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b53e041d8e upstream.
[Why]
We don't check DENTIST_DISPCLK_CHG_DONE to ensure dentist
display clockis updated to target value. In some scenarios with large
display clock margin, it will deliver unfinished display clock and cause
issues like display black screen.
[How]
Checking DENTIST_DISPCLK_CHG_DONE to ensure display clock
has been update to target value before driver do other clock related
actions.
Reviewed-by: Cyr Aric <aric.cyr@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Dale Zhao <dale.zhao@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ca2350e11 upstream.
Commit 670e90924b ("HID: wacom: support named keys on older devices")
added support for sending named events from the soft buttons on the
24HDT and 27QHDT. In the process, however, it inadvertantly disabled the
touchscreen of the 24HDT and 27QHDT by default. The
`wacom_set_shared_values` function would normally enable touch by default
but because it checks the state of the non-shared `has_mute_touch_switch`
flag and `wacom_setup_touch_input_capabilities` sets the state of the
/shared/ version, touch ends up being disabled by default.
This patch sets the non-shared flag, letting `wacom_set_shared_values`
take care of copying the value over to the shared version and setting
the default touch state to "on".
Fixes: 670e90924b ("HID: wacom: support named keys on older devices")
CC: stable@vger.kernel.org # 5.4+
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 640b7ea5f8 upstream.
The memory reserved by console/PALcode or non-volatile memory is not added
to memblock.memory.
Since commit fa3354e4ea (mm: free_area_init: use maximal zone PFNs rather
than zone sizes) the initialization of the memory map relies on the
accuracy of memblock.memory to properly calculate zone sizes. The holes in
memblock.memory caused by absent regions reserved by the firmware cause
incorrect initialization of struct pages which leads to BUG() during the
initial page freeing:
BUG: Bad page state in process swapper pfn:2ffc53
page:fffffc000ecf14c0 refcount:0 mapcount:1 mapping:0000000000000000 index:0x0
flags: 0x0()
raw: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
raw: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
page dumped because: nonzero mapcount
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 5.7.0-03841-gfa3354e4ea39-dirty #26
fffffc0001b5bd68 fffffc0001b5be80 fffffc00011cd148 fffffc000ecf14c0
fffffc00019803df fffffc0001b5be80 fffffc00011ce340 fffffc000ecf14c0
0000000000000000 fffffc0001b5be80 fffffc0001b482c0 fffffc00027d6618
fffffc00027da7d0 00000000002ff97a 0000000000000000 fffffc0001b5be80
fffffc00011d1abc fffffc000ecf14c0 fffffc0002d00000 fffffc0001b5be80
fffffc0001b2350c 0000000000300000 fffffc0001b48298 fffffc0001b482c0
Trace:
[<fffffc00011cd148>] bad_page+0x168/0x1b0
[<fffffc00011ce340>] free_pcp_prepare+0x1e0/0x290
[<fffffc00011d1abc>] free_unref_page+0x2c/0xa0
[<fffffc00014ee5f0>] cmp_ex_sort+0x0/0x30
[<fffffc00014ee5f0>] cmp_ex_sort+0x0/0x30
[<fffffc000101001c>] _stext+0x1c/0x20
Fix this by registering the reserved ranges in memblock.memory.
Link: https://lore.kernel.org/lkml/20210726192311.uffqnanxw3ac5wwi@ivybridge
Fixes: fa3354e4ea ("mm: free_area_init: use maximal zone PFNs rather than zone sizes")
Reported-by: Matt Turner <mattst88@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 928150fad4 upstream.
In esd_usb2_setup_rx_urbs() MAX_RX_URBS coherent buffers are allocated
and there is nothing, that frees them:
1) In callback function the urb is resubmitted and that's all
2) In disconnect function urbs are simply killed, but URB_FREE_BUFFER
is not set (see esd_usb2_setup_rx_urbs) and this flag cannot be used
with coherent buffers.
So, all allocated buffers should be freed with usb_free_coherent()
explicitly.
Side note: This code looks like a copy-paste of other can drivers. The
same patch was applied to mcba_usb driver and it works nice with real
hardware. There is no change in functionality, only clean-up code for
coherent buffers.
Fixes: 96d8e90382 ("can: Add driver for esd CAN-USB/2 device")
Link: https://lore.kernel.org/r/b31b096926dcb35998ad0271aac4b51770ca7cc8.1627404470.git.paskripkin@gmail.com
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9969e3c5f4 upstream.
In ems_usb_start() MAX_RX_URBS coherent buffers are allocated and
there is nothing, that frees them:
1) In callback function the urb is resubmitted and that's all
2) In disconnect function urbs are simply killed, but URB_FREE_BUFFER
is not set (see ems_usb_start) and this flag cannot be used with
coherent buffers.
So, all allocated buffers should be freed with usb_free_coherent()
explicitly.
Side note: This code looks like a copy-paste of other can drivers. The
same patch was applied to mcba_usb driver and it works nice with real
hardware. There is no change in functionality, only clean-up code for
coherent buffers.
Fixes: 702171adee ("ems_usb: Added support for EMS CPC-USB/ARM7 CAN/USB interface")
Link: https://lore.kernel.org/r/59aa9fbc9a8cbf9af2bbd2f61a659c480b415800.1627404470.git.paskripkin@gmail.com
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e865f0c31 upstream.
In usb_8dev_start() MAX_RX_URBS coherent buffers are allocated and
there is nothing, that frees them:
1) In callback function the urb is resubmitted and that's all
2) In disconnect function urbs are simply killed, but URB_FREE_BUFFER
is not set (see usb_8dev_start) and this flag cannot be used with
coherent buffers.
So, all allocated buffers should be freed with usb_free_coherent()
explicitly.
Side note: This code looks like a copy-paste of other can drivers. The
same patch was applied to mcba_usb driver and it works nice with real
hardware. There is no change in functionality, only clean-up code for
coherent buffers.
Fixes: 0024d8ad16 ("can: usb_8dev: Add support for USB2CAN interface from 8 devices")
Link: https://lore.kernel.org/r/d39b458cd425a1cf7f512f340224e6e9563b07bd.1627404470.git.paskripkin@gmail.com
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc43fb69a7 upstream.
Yasushi reported, that his Microchip CAN Analyzer stopped working
since commit 91c0255717 ("can: mcba_usb: fix memory leak in
mcba_usb"). The problem was in missing urb->transfer_dma
initialization.
In my previous patch to this driver I refactored mcba_usb_start() code
to avoid leaking usb coherent buffers. To archive it, I passed local
stack variable to usb_alloc_coherent() and then saved it to private
array to correctly free all coherent buffers on ->close() call. But I
forgot to initialize urb->transfer_dma with variable passed to
usb_alloc_coherent().
All of this was causing device to not work, since dma addr 0 is not
valid and following log can be found on bug report page, which points
exactly to problem described above.
| DMAR: [DMA Write] Request device [00:14.0] PASID ffffffff fault addr 0 [fault reason 05] PTE Write access is not set
Fixes: 91c0255717 ("can: mcba_usb: fix memory leak in mcba_usb")
Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=990850
Link: https://lore.kernel.org/r/20210725103630.23864-1-paskripkin@gmail.com
Cc: linux-stable <stable@vger.kernel.org>
Reported-by: Yasushi SHOJI <yasushi.shoji@gmail.com>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Tested-by: Yasushi SHOJI <yashi@spacecubics.com>
[mkl: fixed typos in commit message - thanks Yasushi SHOJI]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9449ad33be upstream.
For punch holes in EOF blocks, fallocate used buffer write to zero the
EOF blocks in last cluster. But since ->writepage will ignore EOF
pages, those zeros will not be flushed.
This "looks" ok as commit 6bba4471f0 ("ocfs2: fix data corruption by
fallocate") will zero the EOF blocks when extend the file size, but it
isn't. The problem happened on those EOF pages, before writeback, those
pages had DIRTY flag set and all buffer_head in them also had DIRTY flag
set, when writeback run by write_cache_pages(), DIRTY flag on the page
was cleared, but DIRTY flag on the buffer_head not.
When next write happened to those EOF pages, since buffer_head already
had DIRTY flag set, it would not mark page DIRTY again. That made
writeback ignore them forever. That will cause data corruption. Even
directio write can't work because it will fail when trying to drop pages
caches before direct io, as it found the buffer_head for those pages
still had DIRTY flag set, then it will fall back to buffer io mode.
To make a summary of the issue, as writeback ingores EOF pages, once any
EOF page is generated, any write to it will only go to the page cache,
it will never be flushed to disk even file size extends and that page is
not EOF page any more. The fix is to avoid zero EOF blocks with buffer
write.
The following code snippet from qemu-img could trigger the corruption.
656 open("6b3711ae-3306-4bdd-823c-cf1c0060a095.conv.2", O_RDWR|O_DIRECT|O_CLOEXEC) = 11
...
660 fallocate(11, FALLOC_FL_KEEP_SIZE|FALLOC_FL_PUNCH_HOLE, 2275868672, 327680 <unfinished ...>
660 fallocate(11, 0, 2275868672, 327680) = 0
658 pwrite64(11, "
Link: https://lkml.kernel.org/r/20210722054923.24389-2-junxiao.bi@oracle.com
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8750f9bbda upstream.
The arguments to the KVM_CLEAR_DIRTY_LOG ioctl include a pointer,
therefore it needs a compat ioctl implementation. Otherwise,
32-bit userspace fails to invoke it on 64-bit kernels; for x86
it might work fine by chance if the padding is zero, but not
on big-endian architectures.
Reported-by: Thomas Sattler
Cc: stable@vger.kernel.org
Fixes: 2a31b9db15 ("kvm: introduce manual dirty log reprotect")
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 76b4f357d0 upstream.
KVM_MAX_VCPU_ID is the maximum vcpu-id of a guest, and not the number
of vcpu-ids. Fix array indexed by vcpu-id to have KVM_MAX_VCPU_ID+1
elements.
Note that this is currently no real problem, as KVM_MAX_VCPU_ID is
an odd number, resulting in always enough padding being available at
the end of those arrays.
Nevertheless this should be fixed in order to avoid rare problems in
case someone is using an even number for KVM_MAX_VCPU_ID.
Signed-off-by: Juergen Gross <jgross@suse.com>
Message-Id: <20210701154105.23215-2-jgross@suse.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 41a8457f3f upstream.
The current assumption that methods to read PCH FIVR attributes will
return integer, is not correct. There is no good way to return integer
as negative numbers are also valid.
These read methods return a package of integers. The first integer returns
status, which is 0 on success and any other value for failure. When the
returned status is zero, then the second integer returns the actual value.
This change fixes this issue by replacing acpi_evaluate_integer() with
acpi_evaluate_object() and use acpi_extract_package() to extract results.
Fixes: 2ce6324ead ("ACPI: DPTF: Add PCH FIVR participant driver")
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: 5.10+ <stable@vger.kernel.org> # 5.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 240246f6b9 upstream.
In compression write endio sequence, the range which the compressed_bio
writes is marked as uptodate if the last bio of the compressed (sub)bios
is completed successfully. There could be previous bio which may
have failed which is recorded in cb->errors.
Set the writeback range as uptodate only if cb->errors is zero, as opposed
to checking only the last bio's status.
Backporting notes: in all versions up to 4.4 the last argument is always
replaced by "!cb->errors".
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2a6166768 upstream.
When removing a writeable device in __btrfs_free_extra_devids, the rw
device count should be decremented.
This error was caught by Syzbot which reported a warning in
close_fs_devices:
WARNING: CPU: 1 PID: 9355 at fs/btrfs/volumes.c:1168 close_fs_devices+0x763/0x880 fs/btrfs/volumes.c:1168
Modules linked in:
CPU: 0 PID: 9355 Comm: syz-executor552 Not tainted 5.13.0-rc1-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:close_fs_devices+0x763/0x880 fs/btrfs/volumes.c:1168
RSP: 0018:ffffc9000333f2f0 EFLAGS: 00010293
RAX: ffffffff8365f5c3 RBX: 0000000000000001 RCX: ffff888029afd4c0
RDX: 0000000000000000 RSI: 0000000000000001 RDI: 0000000000000000
RBP: ffff88802846f508 R08: ffffffff8365f525 R09: ffffed100337d128
R10: ffffed100337d128 R11: 0000000000000000 R12: dffffc0000000000
R13: ffff888019be8868 R14: 1ffff1100337d10d R15: 1ffff1100337d10a
FS: 00007f6f53828700(0000) GS:ffff8880b9a00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000000047c410 CR3: 00000000302a6000 CR4: 00000000001506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
btrfs_close_devices+0xc9/0x450 fs/btrfs/volumes.c:1180
open_ctree+0x8e1/0x3968 fs/btrfs/disk-io.c:3693
btrfs_fill_super fs/btrfs/super.c:1382 [inline]
btrfs_mount_root+0xac5/0xc60 fs/btrfs/super.c:1749
legacy_get_tree+0xea/0x180 fs/fs_context.c:592
vfs_get_tree+0x86/0x270 fs/super.c:1498
fc_mount fs/namespace.c:993 [inline]
vfs_kern_mount+0xc9/0x160 fs/namespace.c:1023
btrfs_mount+0x3d3/0xb50 fs/btrfs/super.c:1809
legacy_get_tree+0xea/0x180 fs/fs_context.c:592
vfs_get_tree+0x86/0x270 fs/super.c:1498
do_new_mount fs/namespace.c:2905 [inline]
path_mount+0x196f/0x2be0 fs/namespace.c:3235
do_mount fs/namespace.c:3248 [inline]
__do_sys_mount fs/namespace.c:3456 [inline]
__se_sys_mount+0x2f9/0x3b0 fs/namespace.c:3433
do_syscall_64+0x3f/0xb0 arch/x86/entry/common.c:47
entry_SYSCALL_64_after_hwframe+0x44/0xae
Because fs_devices->rw_devices was not 0 after
closing all devices. Here is the call trace that was observed:
btrfs_mount_root():
btrfs_scan_one_device():
device_list_add(); <---------------- device added
btrfs_open_devices():
open_fs_devices():
btrfs_open_one_device(); <-------- writable device opened,
rw device count ++
btrfs_fill_super():
open_ctree():
btrfs_free_extra_devids():
__btrfs_free_extra_devids(); <--- writable device removed,
rw device count not decremented
fail_tree_roots:
btrfs_close_devices():
close_fs_devices(); <------- rw device count off by 1
As a note, prior to commit cf89af146b ("btrfs: dev-replace: fail
mount if we don't have replace item with target device"), rw_devices
was decremented on removing a writable device in
__btrfs_free_extra_devids only if the BTRFS_DEV_STATE_REPLACE_TGT bit
was not set for the device. However, this check does not need to be
reinstated as it is now redundant and incorrect.
In __btrfs_free_extra_devids, we skip removing the device if it is the
target for replacement. This is done by checking whether device->devid
== BTRFS_DEV_REPLACE_DEVID. Since BTRFS_DEV_STATE_REPLACE_TGT is set
only on the device with devid BTRFS_DEV_REPLACE_DEVID, no devices
should have the BTRFS_DEV_STATE_REPLACE_TGT bit set after the check,
and so it's redundant to test for that bit.
Additionally, following commit 82372bc816 ("Btrfs: make
the logic of source device removing more clear"), rw_devices is
incremented whenever a writeable device is added to the alloc
list (including the target device in btrfs_dev_replace_finishing), so
all removals of writable devices from the alloc list should also be
accompanied by a decrement to rw_devices.
Reported-by: syzbot+a70e2ad0879f160b9217@syzkaller.appspotmail.com
Fixes: cf89af146b ("btrfs: dev-replace: fail mount if we don't have replace item with target device")
CC: stable@vger.kernel.org # 5.10+
Tested-by: syzbot+a70e2ad0879f160b9217@syzkaller.appspotmail.com
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a34b13a88 upstream.
Since commit 1b6b26ae70 ("pipe: fix and clarify pipe write wakeup
logic") we have sanitized the pipe write logic, and would only try to
wake up readers if they needed it.
In particular, if the pipe already had data in it before the write,
there was no point in trying to wake up a reader, since any existing
readers must have been aware of the pre-existing data already. Doing
extraneous wakeups will only cause potential thundering herd problems.
However, it turns out that some Android libraries have misused the EPOLL
interface, and expected "edge triggered" be to "any new write will
trigger it". Even if there was no edge in sight.
Quoting Sandeep Patil:
"The commit 1b6b26ae70 ('pipe: fix and clarify pipe write wakeup
logic') changed pipe write logic to wakeup readers only if the pipe
was empty at the time of write. However, there are libraries that
relied upon the older behavior for notification scheme similar to
what's described in [1]
One such library 'realm-core'[2] is used by numerous Android
applications. The library uses a similar notification mechanism as GNU
Make but it never drains the pipe until it is full. When Android moved
to v5.10 kernel, all applications using this library stopped working.
The library has since been fixed[3] but it will be a while before all
applications incorporate the updated library"
Our regression rule for the kernel is that if applications break from
new behavior, it's a regression, even if it was because the application
did something patently wrong. Also note the original report [4] by
Michal Kerrisk about a test for this epoll behavior - but at that point
we didn't know of any actual broken use case.
So add the extraneous wakeup, to approximate the old behavior.
[ I say "approximate", because the exact old behavior was to do a wakeup
not for each write(), but for each pipe buffer chunk that was filled
in. The behavior introduced by this change is not that - this is just
"every write will cause a wakeup, whether necessary or not", which
seems to be sufficient for the broken library use. ]
It's worth noting that this adds the extraneous wakeup only for the
write side, while the read side still considers the "edge" to be purely
about reading enough from the pipe to allow further writes.
See commit f467a6a664 ("pipe: fix and clarify pipe read wakeup logic")
for the pipe read case, which remains that "only wake up if the pipe was
full, and we read something from it".
Link: https://lore.kernel.org/lkml/CAHk-=wjeG0q1vgzu4iJhW5juPkTsjTYmiqiMUYAebWW+0bam6w@mail.gmail.com/ [1]
Link: https://github.com/realm/realm-core [2]
Link: https://github.com/realm/realm-core/issues/4666 [3]
Link: https://lore.kernel.org/lkml/CAKgNAkjMBGeAwF=2MKK758BhxvW58wYTgYKB2V-gY1PwXxrH+Q@mail.gmail.com/ [4]
Link: https://lore.kernel.org/lkml/20210729222635.2937453-1-sspatil@android.com/
Reported-by: Sandeep Patil <sspatil@android.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f7b21a0e41 ]
Fix:
../arch/x86/include/asm/proto.h:14:30: warning: ‘struct task_struct’ declared \
inside parameter list will not be visible outside of this definition or declaration
long do_arch_prctl_64(struct task_struct *task, int option, unsigned long arg2);
^~~~~~~~~~~
.../arch/x86/include/asm/proto.h:40:34: warning: ‘struct task_struct’ declared \
inside parameter list will not be visible outside of this definition or declaration
long do_arch_prctl_common(struct task_struct *task, int option,
^~~~~~~~~~~
if linux/sched.h hasn't be included previously. This fixes a build error
when this header is used outside of the kernel tree.
[ bp: Massage commit message. ]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/b76b4be3-cf66-f6b2-9a6c-3e7ef54f9845@web.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
When backporting 0db282ba2c ("selftest: use mmap instead of
posix_memalign to allocate memory") to this stable branch, I forgot a {
breaking the build.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reduce the default CMA allocation requested by the vc4-kms-v3d-pi4 and
vc4-fkms-v3d-pi4 overlays to 320MB.
Use magic values of the form (<n>*64 - 4)MB to encode default values
of <n>*64MB, allowing these defaults to be distinguished from values
set explicitly by the user with the usual overlay parameters (e.g.
"cma-384"). Only default values will be capped if the Pi RAM is too
small or the gpu_mem setting too large for it to be viable.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Add call to v4l2_ctrl_new_fwnode_properties to read and
create the fwnode based controls.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add call to v4l2_ctrl_new_fwnode_properties to read and
create the fwnode based controls.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add call to v4l2_ctrl_new_fwnode_properties to read and
create the fwnode based controls.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add the orientation parameter to all the camera sensor overlays to
avoid libcamera complaining, and add the rotation parameter where
it hadn't been added before.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
[ Upstream commit 82a1c67554 ]
Once the new schema interrupt-controller/arm,vic.yaml is added, we get
the below warnings:
arch/arm/boot/dts/versatile-ab.dt.yaml:
intc@10140000: $nodename:0: 'intc@10140000' does not match
'^interrupt-controller(@[0-9a-f,]+)*$'
arch/arm/boot/dts/versatile-ab.dt.yaml:
intc@10140000: 'clear-mask' does not match any of the regexes
Fix the node names for the interrupt controller to conform
to the standard node name interrupt-controller@.. Also drop invalid
clear-mask property.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210701132118.759454-1-sudeep.holla@arm.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49694d14ff ]
The length variable is rather pointless given that it can be trivially
deduced from offset and size. Also the initial calculation can lead
to KASAN warnings.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Leizhen (ThunderTown) <thunder.leizhen@huawei.com>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ac1d42651 ]
The length variable is rather pointless given that it can be trivially
deduced from offset and size. Also the initial calculation can lead
to KASAN warnings.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Leizhen (ThunderTown) <thunder.leizhen@huawei.com>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9c9c6815f ]
Because the out of range assignment to bit fields
are compiler-dependant, the fields could have wrong
value.
Signed-off-by: Hyunchul Lee <hyc.lee@gmail.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bdb8742dc6 ]
SCMI message headers carry a sequence number and such field is sized to
allow for MSG_TOKEN_MAX distinct numbers; moreover zero is not really an
acceptable maximum number of pending in-flight messages.
Fix accordingly the checks performed on the value exported by transports
in scmi_desc.max_msg
Link: https://lore.kernel.org/r/20210712141833.6628-3-cristian.marussi@arm.com
Reported-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
[sudeep.holla: updated the patch title and error message]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a691f16cc ]
The scmi_linux_errmap buffer access index is supposed to depend on the
array size to prevent element out of bounds access. It uses SCMI_ERR_MAX
to check bounds but that can mismatch with the array size. It also
changes the success into -EIO though scmi_linux_errmap is never used in
case of success, it is expected to work for success case too.
It is slightly confusing code as the negative of the error code
is used as index to the buffer. Fix it by negating it at the start and
make it more readable.
Link: https://lore.kernel.org/r/20210707135028.1869642-1-sudeep.holla@arm.com
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9ab9cce93 ]
Invoking trc_del_holdout() from within trc_wait_for_one_reader() is
only a performance optimization because the RCU Tasks Trace grace-period
kthread will eventually do this within check_all_holdout_tasks_trace().
But it is not a particularly important performance optimization because
it only applies to the grace-period kthread, of which there is but one.
This commit therefore removes this invocation of trc_del_holdout() in
favor of the one in check_all_holdout_tasks_trace() in the grace-period
kthread.
Reported-by: "Xu, Yanfei" <yanfei.xu@windriver.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d10bf55d8 ]
As Yanfei pointed out, although invoking trc_del_holdout() is safe
from the viewpoint of the integrity of the holdout list itself,
the put_task_struct() invoked by trc_del_holdout() can result in
use-after-free errors due to later accesses to this task_struct structure
by the RCU Tasks Trace grace-period kthread.
This commit therefore removes this call to trc_del_holdout() from
trc_inspect_reader() in favor of the grace-period thread's existing call
to trc_del_holdout(), thus eliminating that particular class of
use-after-free errors.
Reported-by: "Xu, Yanfei" <yanfei.xu@windriver.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d11fa231c ]
The doc draft-stewart-tsvwg-sctp-ipv4-00 that restricts 198 addresses
was never published. These addresses as private addresses should be
allowed to use in SCTP.
As Michael Tuexen suggested, this patch is to move 198 addresses from
unusable to private scope.
Reported-by: Sérgio <surkamp@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0dbffbb533 ]
sk_ll_usec is read locklessly from sk_can_busy_loop()
while another thread can change its value in sock_setsockopt()
This is correct but needs annotations.
BUG: KCSAN: data-race in __skb_try_recv_datagram / sock_setsockopt
write to 0xffff88814eb5f904 of 4 bytes by task 14011 on cpu 0:
sock_setsockopt+0x1287/0x2090 net/core/sock.c:1175
__sys_setsockopt+0x14f/0x200 net/socket.c:2100
__do_sys_setsockopt net/socket.c:2115 [inline]
__se_sys_setsockopt net/socket.c:2112 [inline]
__x64_sys_setsockopt+0x62/0x70 net/socket.c:2112
do_syscall_64+0x4a/0x90 arch/x86/entry/common.c:47
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffff88814eb5f904 of 4 bytes by task 14001 on cpu 1:
sk_can_busy_loop include/net/busy_poll.h:41 [inline]
__skb_try_recv_datagram+0x14f/0x320 net/core/datagram.c:273
unix_dgram_recvmsg+0x14c/0x870 net/unix/af_unix.c:2101
unix_seqpacket_recvmsg+0x5a/0x70 net/unix/af_unix.c:2067
____sys_recvmsg+0x15d/0x310 include/linux/uio.h:244
___sys_recvmsg net/socket.c:2598 [inline]
do_recvmmsg+0x35c/0x9f0 net/socket.c:2692
__sys_recvmmsg net/socket.c:2771 [inline]
__do_sys_recvmmsg net/socket.c:2794 [inline]
__se_sys_recvmmsg net/socket.c:2787 [inline]
__x64_sys_recvmmsg+0xcf/0x150 net/socket.c:2787
do_syscall_64+0x4a/0x90 arch/x86/entry/common.c:47
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0x00000000 -> 0x00000101
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 14001 Comm: syz-executor.3 Not tainted 5.13.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1e7107c5ef upstream.
Richard reported sporadic (roughly one in 10 or so) null dereferences and
other strange behaviour for a set of automated LTP tests. Things like:
BUG: kernel NULL pointer dereference, address: 0000000000000008
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 0 PID: 1516 Comm: umount Not tainted 5.10.0-yocto-standard #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-48-gd9c812dda519-prebuilt.qemu.org 04/01/2014
RIP: 0010:kernfs_sop_show_path+0x1b/0x60
...or these others:
RIP: 0010:do_mkdirat+0x6a/0xf0
RIP: 0010:d_alloc_parallel+0x98/0x510
RIP: 0010:do_readlinkat+0x86/0x120
There were other less common instances of some kind of a general scribble
but the common theme was mount and cgroup and a dubious dentry triggering
the NULL dereference. I was only able to reproduce it under qemu by
replicating Richard's setup as closely as possible - I never did get it
to happen on bare metal, even while keeping everything else the same.
In commit 71d883c37e ("cgroup_do_mount(): massage calling conventions")
we see this as a part of the overall change:
--------------
struct cgroup_subsys *ss;
- struct dentry *dentry;
[...]
- dentry = cgroup_do_mount(&cgroup_fs_type, fc->sb_flags, root,
- CGROUP_SUPER_MAGIC, ns);
[...]
- if (percpu_ref_is_dying(&root->cgrp.self.refcnt)) {
- struct super_block *sb = dentry->d_sb;
- dput(dentry);
+ ret = cgroup_do_mount(fc, CGROUP_SUPER_MAGIC, ns);
+ if (!ret && percpu_ref_is_dying(&root->cgrp.self.refcnt)) {
+ struct super_block *sb = fc->root->d_sb;
+ dput(fc->root);
deactivate_locked_super(sb);
msleep(10);
return restart_syscall();
}
--------------
In changing from the local "*dentry" variable to using fc->root, we now
export/leave that dentry pointer in the file context after doing the dput()
in the unlikely "is_dying" case. With LTP doing a crazy amount of back to
back mount/unmount [testcases/bin/cgroup_regression_5_1.sh] the unlikely
becomes slightly likely and then bad things happen.
A fix would be to not leave the stale reference in fc->root as follows:
--------------
dput(fc->root);
+ fc->root = NULL;
deactivate_locked_super(sb);
--------------
...but then we are just open-coding a duplicate of fc_drop_locked() so we
simply use that instead.
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Tejun Heo <tj@kernel.org>
Cc: Zefan Li <lizefan.x@bytedance.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: stable@vger.kernel.org # v5.1+
Reported-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Fixes: 71d883c37e ("cgroup_do_mount(): massage calling conventions")
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cbcf01128d upstream.
unix_gc() assumes that candidate sockets can never gain an external
reference (i.e. be installed into an fd) while the unix_gc_lock is
held. Except for MSG_PEEK this is guaranteed by modifying inflight
count under the unix_gc_lock.
MSG_PEEK does not touch any variable protected by unix_gc_lock (file
count is not), yet it needs to be serialized with garbage collection.
Do this by locking/unlocking unix_gc_lock:
1) increment file count
2) lock/unlock barrier to make sure incremented file count is visible
to garbage collection
3) install file into fd
This is a lock barrier (unlike smp_mb()) that ensures that garbage
collection is run completely before or completely after the barrier.
Cc: <stable@vger.kernel.org>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f62700ce63 upstream.
selftests/bpf/Makefile includes tools/scripts/Makefile.include.
With the following command
make -j60 LLVM=1 LLVM_IAS=1 <=== compile kernel
make -j60 -C tools/testing/selftests/bpf LLVM=1 LLVM_IAS=1 V=1
some files are still compiled with gcc. This patch
fixed the case if CC/AR/LD/CXX/STRIP is allowed to be
overridden, it will be written to clang/llvm-ar/..., instead of
gcc binaries. The definition of CC_NO_CLANG is also relocated
to the place after the above CC is defined.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210413153419.3028165-1-yhs@fb.com
Cc: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9615fe36b3 upstream.
We will fail to build with CONFIG_SKB_EXTENSIONS disabled after
8550ff8d8c ("skbuff: Release nfct refcount on napi stolen or re-used
skbs") since there is an unconditionally use of skb_ext_find() without
an appropriate stub. Simply build the code conditionally and properly
guard against both COFNIG_SKB_EXTENSIONS as well as
CONFIG_NET_TC_SKB_EXT being disabled.
Fixes: Fixes: 8550ff8d8c ("skbuff: Release nfct refcount on napi stolen or re-used skbs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 788bc000d4 ]
Commit 99ba0ea616 ("sfc: adjust efx->xdp_tx_queue_count with the real
number of initialized queues") intended to fix a problem caused by a
round up when calculating the number of XDP channels and queues.
However, this was not the real problem. The real problem was that the
number of XDP TX queues had been reduced to half in
commit e26ca4b535 ("sfc: reduce the number of requested xdp ev queues"),
but the variable xdp_tx_queue_count had remained the same.
Once the correct number of XDP TX queues is created again in the
previous patch of this series, this also can be reverted since the error
doesn't actually exist.
Only in the case that there is a bug in the code we can have different
values in xdp_queue_number and efx->xdp_tx_queue_count. Because of this,
and per Edward Cree's suggestion, I add instead a WARN_ON to catch if it
happens again in the future.
Note that the number of allocated queues can be higher than the number
of used ones due to the round up, as explained in the existing comment
in the code. That's why we also have to stop increasing xdp_queue_number
beyond efx->xdp_tx_queue_count.
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c90b4503cc upstream.
d3_entered flag is used to mark for vgpu_reset a previous power
transition from D3->D0, typically for VM resume from S3, so that gvt
could skip PPGTT invalidation in current vgpu_reset during resuming.
In case S0ix exit, although there is D3->D0, guest driver continue to
use vgpu as normal, with d3_entered set, until next shutdown/reboot or
power transition.
If a reboot follows a S0ix exit, device power state transite as:
D0->D3->D0->D0(reboot), while system power state transites as:
S0->S0 (reboot). There is no vgpu_reset until D0(reboot), thus
d3_entered won't be cleared, the vgpu_reset will skip PPGTT invalidation
however those PPGTT entries are no longer valid. Err appears like:
gvt: vgpu 2: vfio_pin_pages failed for gfn 0xxxxx, ret -22
gvt: vgpu 2: fail: spt xxxx guest entry 0xxxxx type 2
gvt: vgpu 2: fail: shadow page xxxx guest entry 0xxxxx type 2.
Give gvt a chance to clear d3_entered on elsp cmd submission so that the
states before & after S0ix enter/exit are consistent.
Fixes: ba25d97757 ("drm/i915/gvt: Do not destroy ppgtt_mm during vGPU D3->D0.")
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20210707004531.4873-1-colin.xu@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b60557230 upstream.
When MSI is used by the ehci-hcd driver, it can cause lost interrupts which
results in EHCI only continuing to work due to a polling fallback. But the
reliance of polling drastically reduces performance of any I/O through EHCI.
Interrupts are lost as the EHCI interrupt handler does not safely handle
edge-triggered interrupts. It fails to ensure all interrupt status bits are
cleared, which works with level-triggered interrupts but not the
edge-triggered interrupts typical from using MSI.
To fix this problem, check if the driver may have raced with the hardware
setting additional interrupt status bits and clear status until it is in a
stable state.
Fixes: 306c54d0ed ("usb: hcd: Try MSI interrupts on PCI devices")
Tested-by: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: David Jeffery <djeffery@redhat.com>
Link: https://lore.kernel.org/r/20210715213744.GA44506@redhat
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8550ff8d8c upstream.
When multiple SKBs are merged to a new skb under napi GRO,
or SKB is re-used by napi, if nfct was set for them in the
driver, it will not be released while freeing their stolen
head state or on re-use.
Release nfct on napi's stolen or re-used SKBs, and
in gro_list_prepare, check conntrack metadata diff.
Fixes: 5c6b946047 ("net/mlx5e: CT: Handle misses after executing CT action")
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b69874f74 upstream.
The commit 9a5605505d (" bonding: Add struct bond_ipesc to manage SA") is causing
following build error when XFRM is not selected in kernel config.
lld: error: undefined symbol: xfrm_dev_state_flush
>>> referenced by bond_main.c:3453 (drivers/net/bonding/bond_main.c:3453)
>>> net/bonding/bond_main.o:(bond_netdev_event) in archive drivers/built-in.a
Fixes: 9a5605505d (" bonding: Add struct bond_ipesc to manage SA")
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
CC: Taehee Yoo <ap420073@gmail.com>
CC: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 953b0dcbe2 upstream.
Commit bf3504cea7 ("net: dsa: mv88e6xxx: Add 6390 family PCS
registers to ethtool -d") added support for dumping SerDes PCS registers
via ethtool -d for Peridot.
The same implementation is also valid for Topaz, but was not
enabled at the time.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: bf3504cea7 ("net: dsa: mv88e6xxx: Add 6390 family PCS registers to ethtool -d")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a03b98d683 upstream.
Commit 0df9528736 ("mv88e6xxx: Add serdes Rx statistics") added
support for RX statistics on SerDes ports for Peridot.
This same implementation is also valid for Topaz, but was not enabled
at the time.
We need to use the generic .serdes_get_lane() method instead of the
Peridot specific one in the stats methods so that on Topaz the proper
one is used.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: 0df9528736 ("mv88e6xxx: Add serdes Rx statistics")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3abab27c32 upstream.
drm: Return -ENOTTY for non-drm ioctls
Return -ENOTTY from drm_ioctl() when userspace passes in a cmd number
which doesn't relate to the drm subsystem.
Glibc uses the TCGETS ioctl to implement isatty(), and without this
change isatty() returns it incorrectly returns true for drm devices.
To test run this command:
$ if [ -t 0 ]; then echo is a tty; fi < /dev/dri/card0
which shows "is a tty" without this patch.
This may also modify memory which the userspace application is not
expecting.
Signed-off-by: Charles Baylis <cb-kernel@fishzet.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/YPG3IBlzaMhfPqCr@stando.fishzet.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c36748ac54 upstream.
We need to append device id even if eeprom have a label property set as some
platform can have multiple eeproms with same label and we can not register
each of those with same label. Failing to register those eeproms trigger
cascade failures on such platform (system is no longer working).
This fix regression on such platform introduced with 4e302c3b56
Reported-by: Alexander Fomichev <fomichev.ru@gmail.com>
Fixes: 4e302c3b56 ("misc: eeprom: at24: fix NVMEM name with custom AT24 device name")
Cc: stable@vger.kernel.org
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8798d070d4 upstream.
Skipping the "lock has been released" notification if the lock owner
is not what we expect based on owner_cid can lead to I/O hangs.
One example is our own notifications: because owner_cid is cleared
in rbd_unlock(), when we get our own notification it is processed as
unexpected/duplicate and maybe_kick_acquire() isn't called. If a peer
that requested the lock then doesn't go through with acquiring it,
I/O requests that came in while the lock was being quiesced would
be stalled until another I/O request is submitted and kicks acquire
from rbd_img_exclusive_lock().
This makes the comment in rbd_release_lock() actually true: prior to
this change the canceled work was being requeued in response to the
"lock has been acquired" notification from rbd_handle_acquired_lock().
Cc: stable@vger.kernel.org # 5.3+
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Tested-by: Robin Geuze <robin.geuze@nl.team.blue>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed9eb71085 upstream.
Currently rbd_quiesce_lock() holds lock_rwsem for read while blocking
on releasing_wait completion. On the I/O completion side, each image
request also needs to take lock_rwsem for read. Because rw_semaphore
implementation doesn't allow new readers after a writer has indicated
interest in the lock, this can result in a deadlock if something that
needs to take lock_rwsem for write gets involved. For example:
1. watch error occurs
2. rbd_watch_errcb() takes lock_rwsem for write, clears owner_cid and
releases lock_rwsem
3. after reestablishing the watch, rbd_reregister_watch() takes
lock_rwsem for write and calls rbd_reacquire_lock()
4. rbd_quiesce_lock() downgrades lock_rwsem to for read and blocks on
releasing_wait until running_list becomes empty
5. another watch error occurs
6. rbd_watch_errcb() blocks trying to take lock_rwsem for write
7. no in-flight image request can complete and delete itself from
running_list because lock_rwsem won't be granted anymore
A similar scenario can occur with "lock has been acquired" and "lock
has been released" notification handers which also take lock_rwsem for
write to update owner_cid.
We don't actually get anything useful from sitting on lock_rwsem in
rbd_quiesce_lock() -- owner_cid updates certainly don't need to be
synchronized with. In fact the whole owner_cid tracking logic could
probably be removed from the kernel client because we don't support
proxied maintenance operations.
Cc: stable@vger.kernel.org # 5.3+
URL: https://tracker.ceph.com/issues/42757
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Tested-by: Robin Geuze <robin.geuze@nl.team.blue>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 79e482e9c3 upstream.
Commit b10d6bca87 ("arch, drivers: replace for_each_membock() with
for_each_mem_range()") didn't take into account that when there is
movable_node parameter in the kernel command line, for_each_mem_range()
would skip ranges marked with MEMBLOCK_HOTPLUG.
The page table setup code in POWER uses for_each_mem_range() to create
the linear mapping of the physical memory and since the regions marked
as MEMORY_HOTPLUG are skipped, they never make it to the linear map.
A later access to the memory in those ranges will fail:
BUG: Unable to handle kernel data access on write at 0xc000000400000000
Faulting instruction address: 0xc00000000008a3c0
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Radix SMP NR_CPUS=2048 NUMA pSeries
Modules linked in:
CPU: 0 PID: 53 Comm: kworker/u2:0 Not tainted 5.13.0 #7
NIP: c00000000008a3c0 LR: c0000000003c1ed8 CTR: 0000000000000040
REGS: c000000008a57770 TRAP: 0300 Not tainted (5.13.0)
MSR: 8000000002009033 <SF,VEC,EE,ME,IR,DR,RI,LE> CR: 84222202 XER: 20040000
CFAR: c0000000003c1ed4 DAR: c000000400000000 DSISR: 42000000 IRQMASK: 0
GPR00: c0000000003c1ed8 c000000008a57a10 c0000000019da700 c000000400000000
GPR04: 0000000000000280 0000000000000180 0000000000000400 0000000000000200
GPR08: 0000000000000100 0000000000000080 0000000000000040 0000000000000300
GPR12: 0000000000000380 c000000001bc0000 c0000000001660c8 c000000006337e00
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: 0000000040000000 0000000020000000 c000000001a81990 c000000008c30000
GPR24: c000000008c20000 c000000001a81998 000fffffffff0000 c000000001a819a0
GPR28: c000000001a81908 c00c000001000000 c000000008c40000 c000000008a64680
NIP clear_user_page+0x50/0x80
LR __handle_mm_fault+0xc88/0x1910
Call Trace:
__handle_mm_fault+0xc44/0x1910 (unreliable)
handle_mm_fault+0x130/0x2a0
__get_user_pages+0x248/0x610
__get_user_pages_remote+0x12c/0x3e0
get_arg_page+0x54/0xf0
copy_string_kernel+0x11c/0x210
kernel_execve+0x16c/0x220
call_usermodehelper_exec_async+0x1b0/0x2f0
ret_from_kernel_thread+0x5c/0x70
Instruction dump:
79280fa4 79271764 79261f24 794ae8e2 7ca94214 7d683a14 7c893a14 7d893050
7d4903a6 60000000 60000000 60000000 <7c001fec> 7c091fec 7c081fec 7c051fec
---[ end trace 490b8c67e6075e09 ]---
Making for_each_mem_range() include MEMBLOCK_HOTPLUG regions in the
traversal fixes this issue.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1976100
Link: https://lkml.kernel.org/r/20210712071132.20902-1-rppt@kernel.org
Fixes: b10d6bca87 ("arch, drivers: replace for_each_membock() with for_each_mem_range()")
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Tested-by: Greg Kurz <groug@kaod.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: <stable@vger.kernel.org> [5.10+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e71e2ace57 upstream.
Patch series "userfaultfd: do not untag user pointers", v5.
If a user program uses userfaultfd on ranges of heap memory, it may end
up passing a tagged pointer to the kernel in the range.start field of
the UFFDIO_REGISTER ioctl. This can happen when using an MTE-capable
allocator, or on Android if using the Tagged Pointers feature for MTE
readiness [1].
When a fault subsequently occurs, the tag is stripped from the fault
address returned to the application in the fault.address field of struct
uffd_msg. However, from the application's perspective, the tagged
address *is* the memory address, so if the application is unaware of
memory tags, it may get confused by receiving an address that is, from
its point of view, outside of the bounds of the allocation. We observed
this behavior in the kselftest for userfaultfd [2] but other
applications could have the same problem.
Address this by not untagging pointers passed to the userfaultfd ioctls.
Instead, let the system call fail. Also change the kselftest to use
mmap so that it doesn't encounter this problem.
[1] https://source.android.com/devices/tech/debug/tagged-pointers
[2] tools/testing/selftests/vm/userfaultfd.c
This patch (of 2):
Do not untag pointers passed to the userfaultfd ioctls. Instead, let
the system call fail. This will provide an early indication of problems
with tag-unaware userspace code instead of letting the code get confused
later, and is consistent with how we decided to handle brk/mmap/mremap
in commit dcde237319 ("mm: Avoid creating virtual address aliases in
brk()/mmap()/mremap()"), as well as being consistent with the existing
tagged address ABI documentation relating to how ioctl arguments are
handled.
The code change is a revert of commit 7d0325749a ("userfaultfd: untag
user pointers") plus some fixups to some additional calls to
validate_range that have appeared since then.
[1] https://source.android.com/devices/tech/debug/tagged-pointers
[2] tools/testing/selftests/vm/userfaultfd.c
Link: https://lkml.kernel.org/r/20210714195437.118982-1-pcc@google.com
Link: https://lkml.kernel.org/r/20210714195437.118982-2-pcc@google.com
Link: https://linux-review.googlesource.com/id/I761aa9f0344454c482b83fcfcce547db0a25501b
Fixes: 63f0c60379 ("arm64: Introduce prctl() options to control the tagged user addresses ABI")
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Alistair Delva <adelva@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Dave Martin <Dave.Martin@arm.com>
Cc: Evgenii Stepanov <eugenis@google.com>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: Mitch Phillips <mitchp@google.com>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: William McVicker <willmcvicker@google.com>
Cc: <stable@vger.kernel.org> [5.4]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46fee9ab02 upstream.
__io_queue_proc() can enqueue both poll entries and still fail
afterwards, so the callers trying to cancel it should also try to remove
the second poll entry (if any).
For example, it may leave the request alive referencing a io_uring
context but not accessible for cancellation:
[ 282.599913][ T1620] task:iou-sqp-23145 state:D stack:28720 pid:23155 ppid: 8844 flags:0x00004004
[ 282.609927][ T1620] Call Trace:
[ 282.613711][ T1620] __schedule+0x93a/0x26f0
[ 282.634647][ T1620] schedule+0xd3/0x270
[ 282.638874][ T1620] io_uring_cancel_generic+0x54d/0x890
[ 282.660346][ T1620] io_sq_thread+0xaac/0x1250
[ 282.696394][ T1620] ret_from_fork+0x1f/0x30
Cc: stable@vger.kernel.org
Fixes: 18bceab101 ("io_uring: allow POLL_ADD with double poll_wait() users")
Reported-and-tested-by: syzbot+ac957324022b7132accf@syzkaller.appspotmail.com
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/0ec1228fc5eda4cb524eeda857da8efdc43c331c.1626774457.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a3402d93c upstream.
Since the process wide cputime counter is started locklessly from
posix_cpu_timer_rearm(), it can be concurrently stopped by operations
on other timers from the same thread group, such as in the following
unlucky scenario:
CPU 0 CPU 1
----- -----
timer_settime(TIMER B)
posix_cpu_timer_rearm(TIMER A)
cpu_clock_sample_group()
(pct->timers_active already true)
handle_posix_cpu_timers()
check_process_timers()
stop_process_timers()
pct->timers_active = false
arm_timer(TIMER A)
tick -> run_posix_cpu_timers()
// sees !pct->timers_active, ignore
// our TIMER A
Fix this with simply locking process wide cputime counting start and
timer arm in the same block.
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Fixes: 60f2ceaa81 ("posix-cpu-timers: Remove unnecessary locking around cpu_clock_sample_group")
Cc: stable@vger.kernel.org
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09cfae9f13 upstream.
When receiving a packet with multiple fragments, hardware may still
touch the first fragment until the entire packet has been received. The
driver therefore keeps the first fragment mapped for DMA until end of
packet has been asserted, and delays its dma_sync call until then.
The driver tries to fit multiple receive buffers on one page. When using
3K receive buffers (e.g. using Jumbo frames and legacy-rx is turned
off/build_skb is being used) on an architecture with 4K pages, the
driver allocates an order 1 compound page and uses one page per receive
buffer. To determine the correct offset for a delayed DMA sync of the
first fragment of a multi-fragment packet, the driver then cannot just
use PAGE_MASK on the DMA address but has to construct a mask based on
the actual size of the backing page.
Using PAGE_MASK in the 3K RX buffer/4K page architecture configuration
will always sync the first page of a compound page. With the SWIOTLB
enabled this can lead to corrupted packets (zeroed out first fragment,
re-used garbage from another packet) and various consequences, such as
slow/stalling data transfers and connection resets. For example, testing
on a link with MTU exceeding 3058 bytes on a host with SWIOTLB enabled
(e.g. "iommu=soft swiotlb=262144,force") TCP transfers quickly fizzle
out without this patch.
Cc: stable@vger.kernel.org
Fixes: 0c5661ecc5 ("ixgbe: fix crash in build_skb Rx code path")
Signed-off-by: Markus Boehme <markubo@amazon.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d4abca95e upstream.
Fix an 11-year old bug in ngene_command_config_free_buf() while
addressing the following warnings caught with -Warray-bounds:
arch/alpha/include/asm/string.h:22:16: warning: '__builtin_memcpy' offset [12, 16] from the object at 'com' is out of the bounds of referenced subobject 'config' with type 'unsigned char' at offset 10 [-Warray-bounds]
arch/x86/include/asm/string_32.h:182:25: warning: '__builtin_memcpy' offset [12, 16] from the object at 'com' is out of the bounds of referenced subobject 'config' with type 'unsigned char' at offset 10 [-Warray-bounds]
The problem is that the original code is trying to copy 6 bytes of
data into a one-byte size member _config_ of the wrong structue
FW_CONFIGURE_BUFFERS, in a single call to memcpy(). This causes a
legitimate compiler warning because memcpy() overruns the length
of &com.cmd.ConfigureBuffers.config. It seems that the right
structure is FW_CONFIGURE_FREE_BUFFERS, instead, because it contains
6 more members apart from the header _hdr_. Also, the name of
the function ngene_command_config_free_buf() suggests that the actual
intention is to ConfigureFreeBuffers, instead of ConfigureBuffers
(which takes place in the function ngene_command_config_buf(), above).
Fix this by enclosing those 6 members of struct FW_CONFIGURE_FREE_BUFFERS
into new struct config, and use &com.cmd.ConfigureFreeBuffers.config as
the destination address, instead of &com.cmd.ConfigureBuffers.config,
when calling memcpy().
This also helps with the ongoing efforts to globally enable
-Warray-bounds and get us closer to being able to tighten the
FORTIFY_SOURCE routines on memcpy().
Link: https://github.com/KSPP/linux/issues/109
Fixes: dae52d009f ("V4L/DVB: ngene: Initial check-in")
Cc: stable@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/linux-hardening/20210420001631.GA45456@embeddedor/
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67f0d6d988 upstream.
The "rb_per_cpu_empty()" misinterpret the condition (as not-empty) when
"head_page" and "commit_page" of "struct ring_buffer_per_cpu" points to
the same buffer page, whose "buffer_data_page" is empty and "read" field
is non-zero.
An error scenario could be constructed as followed (kernel perspective):
1. All pages in the buffer has been accessed by reader(s) so that all of
them will have non-zero "read" field.
2. Read and clear all buffer pages so that "rb_num_of_entries()" will
return 0 rendering there's no more data to read. It is also required
that the "read_page", "commit_page" and "tail_page" points to the same
page, while "head_page" is the next page of them.
3. Invoke "ring_buffer_lock_reserve()" with large enough "length"
so that it shot pass the end of current tail buffer page. Now the
"head_page", "commit_page" and "tail_page" points to the same page.
4. Discard current event with "ring_buffer_discard_commit()", so that
"head_page", "commit_page" and "tail_page" points to a page whose buffer
data page is now empty.
When the error scenario has been constructed, "tracing_read_pipe" will
be trapped inside a deadloop: "trace_empty()" returns 0 since
"rb_per_cpu_empty()" returns 0 when it hits the CPU containing such
constructed ring buffer. Then "trace_find_next_entry_inc()" always
return NULL since "rb_num_of_entries()" reports there's no more entry
to read. Finally "trace_seq_to_user()" returns "-EBUSY" spanking
"tracing_read_pipe" back to the start of the "waitagain" loop.
I've also written a proof-of-concept script to construct the scenario
and trigger the bug automatically, you can use it to trace and validate
my reasoning above:
https://github.com/aegistudio/RingBufferDetonator.git
Tests has been carried out on linux kernel 5.14-rc2
(2734d6c1b1), my fixed version
of kernel (for testing whether my update fixes the bug) and
some older kernels (for range of affected kernels). Test result is
also attached to the proof-of-concept repository.
Link: https://lore.kernel.org/linux-trace-devel/YPaNxsIlb2yjSi5Y@aegistudio/
Link: https://lore.kernel.org/linux-trace-devel/YPgrN85WL9VyrZ55@aegistudio
Cc: stable@vger.kernel.org
Fixes: bf41a158ca ("ring-buffer: make reentrant")
Suggested-by: Linus Torvalds <torvalds@linuxfoundation.org>
Signed-off-by: Haoran Luo <www@aegistudio.net>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e3bac71c5 upstream.
Currently the histogram logic allows the user to write "cpu" in as an
event field, and it will record the CPU that the event happened on.
The problem with this is that there's a lot of events that have "cpu"
as a real field, and using "cpu" as the CPU it ran on, makes it
impossible to run histograms on the "cpu" field of events.
For example, if I want to have a histogram on the count of the
workqueue_queue_work event on its cpu field, running:
># echo 'hist:keys=cpu' > events/workqueue/workqueue_queue_work/trigger
Gives a misleading and wrong result.
Change the command to "common_cpu" as no event should have "common_*"
fields as that's a reserved name for fields used by all events. And
this makes sense here as common_cpu would be a field used by all events.
Now we can even do:
># echo 'hist:keys=common_cpu,cpu if cpu < 100' > events/workqueue/workqueue_queue_work/trigger
># cat events/workqueue/workqueue_queue_work/hist
# event histogram
#
# trigger info: hist:keys=common_cpu,cpu:vals=hitcount:sort=hitcount:size=2048 if cpu < 100 [active]
#
{ common_cpu: 0, cpu: 2 } hitcount: 1
{ common_cpu: 0, cpu: 4 } hitcount: 1
{ common_cpu: 7, cpu: 7 } hitcount: 1
{ common_cpu: 0, cpu: 7 } hitcount: 1
{ common_cpu: 0, cpu: 1 } hitcount: 1
{ common_cpu: 0, cpu: 6 } hitcount: 2
{ common_cpu: 0, cpu: 5 } hitcount: 2
{ common_cpu: 1, cpu: 1 } hitcount: 4
{ common_cpu: 6, cpu: 6 } hitcount: 4
{ common_cpu: 5, cpu: 5 } hitcount: 14
{ common_cpu: 4, cpu: 4 } hitcount: 26
{ common_cpu: 0, cpu: 0 } hitcount: 39
{ common_cpu: 2, cpu: 2 } hitcount: 184
Now for backward compatibility, I added a trick. If "cpu" is used, and
the field is not found, it will fall back to "common_cpu" and work as
it did before. This way, it will still work for old programs that use
"cpu" to get the actual CPU, but if the event has a "cpu" as a field, it
will get that event's "cpu" field, which is probably what it wants
anyway.
I updated the tracefs/README to include documentation about both the
common_timestamp and the common_cpu. This way, if that text is present in
the README, then an application can know that common_cpu is supported over
just plain "cpu".
Link: https://lkml.kernel.org/r/20210721110053.26b4f641@oasis.local.home
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@vger.kernel.org
Fixes: 8b7622bf94 ("tracing: Add cpu field for hist triggers")
Reviewed-by: Tom Zanussi <zanussi@kernel.org>
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 352384d5c8 upstream.
Because of the significant overhead that retpolines pose on indirect
calls, the tracepoint code was updated to use the new "static_calls" that
can modify the running code to directly call a function instead of using
an indirect caller, and this function can be changed at runtime.
In the tracepoint code that calls all the registered callbacks that are
attached to a tracepoint, the following is done:
it_func_ptr = rcu_dereference_raw((&__tracepoint_##name)->funcs);
if (it_func_ptr) {
__data = (it_func_ptr)->data;
static_call(tp_func_##name)(__data, args);
}
If there's just a single callback, the static_call is updated to just call
that callback directly. Once another handler is added, then the static
caller is updated to call the iterator, that simply loops over all the
funcs in the array and calls each of the callbacks like the old method
using indirect calling.
The issue was discovered with a race between updating the funcs array and
updating the static_call. The funcs array was updated first and then the
static_call was updated. This is not an issue as long as the first element
in the old array is the same as the first element in the new array. But
that assumption is incorrect, because callbacks also have a priority
field, and if there's a callback added that has a higher priority than the
callback on the old array, then it will become the first callback in the
new array. This means that it is possible to call the old callback with
the new callback data element, which can cause a kernel panic.
static_call = callback1()
funcs[] = {callback1,data1};
callback2 has higher priority than callback1
CPU 1 CPU 2
----- -----
new_funcs = {callback2,data2},
{callback1,data1}
rcu_assign_pointer(tp->funcs, new_funcs);
/*
* Now tp->funcs has the new array
* but the static_call still calls callback1
*/
it_func_ptr = tp->funcs [ new_funcs ]
data = it_func_ptr->data [ data2 ]
static_call(callback1, data);
/* Now callback1 is called with
* callback2's data */
[ KERNEL PANIC ]
update_static_call(iterator);
To prevent this from happening, always switch the static_call to the
iterator before assigning the tp->funcs to the new array. The iterator will
always properly match the callback with its data.
To trigger this bug:
In one terminal:
while :; do hackbench 50; done
In another terminal
echo 1 > /sys/kernel/tracing/events/sched/sched_waking/enable
while :; do
echo 1 > /sys/kernel/tracing/set_event_pid;
sleep 0.5
echo 0 > /sys/kernel/tracing/set_event_pid;
sleep 0.5
done
And it doesn't take long to crash. This is because the set_event_pid adds
a callback to the sched_waking tracepoint with a high priority, which will
be called before the sched_waking trace event callback is called.
Note, the removal to a single callback updates the array first, before
changing the static_call to single callback, which is the proper order as
the first element in the array is the same as what the static_call is
being changed to.
Link: https://lore.kernel.org/io-uring/4ebea8f0-58c9-e571-fd30-0ce4f6f09c70@samba.org/
Cc: stable@vger.kernel.org
Fixes: d25e37d89d ("tracepoint: Optimize using static_call()")
Reported-by: Stefan Metzmacher <metze@samba.org>
tested-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2bab693a60 upstream.
kexec_load_file() relies on the memblock infrastructure to avoid
stamping over regions of memory that are essential to the survival
of the system.
However, nobody seems to agree how to flag these regions as reserved,
and (for example) EFI only publishes its reservations in /proc/iomem
for the benefit of the traditional, userspace based kexec tool.
On arm64 platforms with GICv3, this can result in the payload being
placed at the location of the LPI tables. Shock, horror!
Let's augment the EFI reservation code with a memblock_reserve() call,
protecting our dear tables from the secondary kernel invasion.
Reported-by: Moritz Fischer <mdf@kernel.org>
Tested-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 86762ad4ab upstream.
During interrupt registration, attach state is checked. If attached,
then the Type-C state is updated with typec_set_xxx functions and role
switch is set with usb_role_switch_set_role().
If the usb_role_switch parameter is error or null, the function simply
returns 0.
So, to update usb_role_switch role if a device is attached before the
irq is registered, usb_role_switch must be registered before irq
registration.
Fixes: da0cb63100 ("usb: typec: add support for STUSB160x Type-C controller family")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20210716120718.20398-2-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fecb3a171d upstream.
Because of dwc2_hsotg_ep_stop_xfr() function uses poll
mode, first need to mask GINTSTS_GOUTNAKEFF interrupt.
In Slave mode GINTSTS_GOUTNAKEFF interrupt will be
aserted only after pop OUT NAK status packet from RxFIFO.
In dwc2_hsotg_ep_sethalt() function before setting
DCTL_SGOUTNAK need to unmask GOUTNAKEFF interrupt.
Tested by USBCV CH9 and MSC tests set in Slave, BDMA and DDMA.
All tests are passed.
Fixes: a4f8277145 ("usb: dwc2: gadget: Disable enabled HW endpoint in dwc2_hsotg_ep_disable")
Fixes: 6070636c49 ("usb: dwc2: Fix Stalling a Non-Isochronous OUT EP")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/e17fad802bbcaf879e1ed6745030993abb93baf8.1626152924.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5719df243e upstream.
This driver has a potential issue which this driver is possible to
cause superfluous irqs after usb_pkt_pop() is called. So, after
the commit 3af3260528 ("usb: renesas_usbhs: fix error return
code of usbhsf_pkt_handler()") had been applied, we could observe
the following error happened when we used g_audio.
renesas_usbhs e6590000.usb: irq_ready run_error 1 : -22
To fix the issue, disable the tx or rx interrupt in usb_pkt_pop().
Fixes: 2743e7f90d ("usb: renesas_usbhs: fix the usb_pkt_pop()")
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210624122039.596528-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5fdf5c6e6 upstream.
The MAX-3421 USB driver remembers the state of the USB toggles for a
device/endpoint. To save SPI writes, this was only done when a new
device/endpoint was being used. Unfortunately, if the old device was
removed, this would cause writes to freed memory.
To fix this, a simpler scheme is used. The toggles are read from
hardware when a URB is completed, and the toggles are always written to
hardware when any URB transaction is started. This will cause a few more
SPI transactions, but no causes kernel panics.
Fixes: 2d53139f31 ("Add support for using a MAX3421E chip as a host driver.")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20210625031456.8632-1-mark.tomlinson@alliedtelesis.co.nz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1bf2761c83 upstream.
Maximum Exit Latency (MEL) value is used by host to know how much in
advance it needs to start waking up a U1/U2 suspended link in order to
service a periodic transfer in time.
Current MEL calculation only includes the time to wake up the path from
U1/U2 to U0. This is called tMEL1 in USB 3.1 section C 1.5.2
Total MEL = tMEL1 + tMEL2 +tMEL3 + tMEL4 which should additinally include:
- tMEL2 which is the time it takes for PING message to reach device
- tMEL3 time for device to process the PING and submit a PING_RESPONSE
- tMEL4 time for PING_RESPONSE to traverse back upstream to host.
Add the missing tMEL2, tMEL3 and tMEL4 to MEL calculation.
Cc: <stable@kernel.org> # v3.5
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210715150122.1995966-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b7f56fbc7 upstream.
The device initiated link power management U1/U2 states should not be
enabled in case the system exit latency plus one bus interval (125us) is
greater than the shortest service interval of any periodic endpoint.
This is the case for both U1 and U2 sytstem exit latencies and link states.
See USB 3.2 section 9.4.9 "Set Feature" for more details
Note, before this patch the host and device initiated U1/U2 lpm states
were both enabled with lpm. After this patch it's possible to end up with
only host inititated U1/U2 lpm in case the exit latencies won't allow
device initiated lpm.
If this case we still want to set the udev->usb3_lpm_ux_enabled flag so
that sysfs users can see the link may go to U1/U2.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210715150122.1995966-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9c57d3ed5 upstream.
The H_ENTER_NESTED hypercall is handled by the L0, and it is a request
by the L1 to switch the context of the vCPU over to that of its L2
guest, and return with an interrupt indication. The L1 is responsible
for switching some registers to guest context, and the L0 switches
others (including all the hypervisor privileged state).
If the L2 MSR has TM active, then the L1 is responsible for
recheckpointing the L2 TM state. Then the L1 exits to L0 via the
H_ENTER_NESTED hcall, and the L0 saves the TM state as part of the exit,
and then it recheckpoints the TM state as part of the nested entry and
finally HRFIDs into the L2 with TM active MSR. Not efficient, but about
the simplest approach for something that's horrendously complicated.
Problems arise if the L1 exits to the L0 with a TM state which does not
match the L2 TM state being requested. For example if the L1 is
transactional but the L2 MSR is non-transactional, or vice versa. The
L0's HRFID can take a TM Bad Thing interrupt and crash.
Fix this by disallowing H_ENTER_NESTED in TM[T] state entirely, and then
ensuring that if the L1 is suspended then the L2 must have TM active,
and if the L1 is not suspended then the L2 must not have TM active.
Fixes: 360cae3137 ("KVM: PPC: Book3S HV: Nested guest entry via hypercall")
Cc: stable@vger.kernel.org # v4.20+
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f62f3c2064 upstream.
The kvmppc_rtas_hcall() sets the host rtas_args.rets pointer based on
the rtas_args.nargs that was provided by the guest. That guest nargs
value is not range checked, so the guest can cause the host rets pointer
to be pointed outside the args array. The individual rtas function
handlers check the nargs and nrets values to ensure they are correct,
but if they are not, the handlers store a -3 (0xfffffffd) failure
indication in rets[0] which corrupts host memory.
Fix this by testing up front whether the guest supplied nargs and nret
would exceed the array size, and fail the hcall directly without storing
a failure indication to rets[0].
Also expand on a comment about why we kill the guest and try not to
return errors directly if we have a valid rets[0] pointer.
Fixes: 8e591cb720 ("KVM: PPC: Book3S: Add infrastructure to implement kernel-side RTAS calls")
Cc: stable@vger.kernel.org # v3.10+
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72f68bf5c7 upstream.
There's a small window where a USB 2 remote wake may be left unhandled
due to a race between hub thread and xhci port event interrupt handler.
When the resume event is detected in the xhci interrupt handler it kicks
the hub timer, which should move the port from resume to U0 once resume
has been signalled for long enough.
To keep the hub "thread" running we set a bus_state->resuming_ports flag.
This flag makes sure hub timer function kicks itself.
checking this flag was not properly protected by the spinlock. Flag was
copied to a local variable before lock was taken. The local variable was
then checked later with spinlock held.
If interrupt is handled right after copying the flag to the local variable
we end up stopping the hub thread before it can handle the USB 2 resume.
CPU0 CPU1
(hub thread) (xhci event handler)
xhci_hub_status_data()
status = bus_state->resuming_ports;
<Interrupt>
handle_port_status()
spin_lock()
bus_state->resuming_ports = 1
set_flag(HCD_FLAG_POLL_RH)
spin_unlock()
spin_lock()
if (!status)
clear_flag(HCD_FLAG_POLL_RH)
spin_unlock()
Fix this by taking the lock a bit earlier so that it covers
the resuming_ports flag copy in the hub thread
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210715150651.1996099-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0665e38731 upstream.
Commit a66d21d7db ("usb: xhci: Add support for Renesas controller with
memory") added renesas_usb_fw.mem firmware reference to xhci-pci. Thus
modinfo indicates xhci-pci.ko has "firmware: renesas_usb_fw.mem". But
the firmware is only actually used with CONFIG_USB_XHCI_PCI_RENESAS. An
unusable firmware reference can trigger safety checkers which look for
drivers with unmet firmware dependencies.
Avoid referring to renesas_usb_fw.mem in circumstances when it cannot be
loaded (when CONFIG_USB_XHCI_PCI_RENESAS isn't set).
Fixes: a66d21d7db ("usb: xhci: Add support for Renesas controller with memory")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Thelen <gthelen@google.com>
Link: https://lore.kernel.org/r/20210702071224.3673568-1-gthelen@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e2832562c upstream.
If a 32-bit application is being used with a 64-bit kernel and is using
the mmap mechanism to write data, then the SNDRV_PCM_IOCTL_SYNC_PTR
ioctl results in calling snd_pcm_ioctl_sync_ptr_compat(). Make this use
pcm_lib_apply_appl_ptr() so that the substream's ack() method, if
defined, is called.
The snd_pcm_sync_ptr() function, used in the 64-bit ioctl case, already
uses snd_pcm_ioctl_sync_ptr_compat().
Fixes: 9027c4639e ("ALSA: pcm: Call ack() whenever appl_ptr is updated")
Signed-off-by: Alan Young <consult.awy@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/c441f18c-eb2a-3bdd-299a-696ccca2de9c@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c2b951915 upstream.
SB16 CSP driver may hit potentially a typical ABBA deadlock in two
code paths:
In snd_sb_csp_stop():
spin_lock_irqsave(&p->chip->mixer_lock, flags);
spin_lock(&p->chip->reg_lock);
In snd_sb_csp_load():
spin_lock_irqsave(&p->chip->reg_lock, flags);
spin_lock(&p->chip->mixer_lock);
Also the similar pattern is seen in snd_sb_csp_start().
Although the practical impact is very small (those states aren't
triggered in the same running state and this happens only on a real
hardware, decades old ISA sound boards -- which must be very difficult
to find nowadays), it's a real scenario and has to be fixed.
This patch addresses those deadlocks by splitting the locks in
snd_sb_csp_start() and snd_sb_csp_stop() for avoiding the nested
locks.
Reported-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/7b0fcdaf-cd4f-4728-2eae-48c151a92e10@gmail.com
Link: https://lore.kernel.org/r/20210716132723.13216-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 64752a95b7 upstream.
Recently we've added a new usb_mixer element type, USB_MIXER_BESPOKEN,
but it wasn't added in the table in snd_usb_mixer_dump_cval(). This
is no big problem since each bespoken type should have its own dump
method, but it still isn't disallowed to use the standard one, so we
should cover it as well. Along with it, define the table with the
explicit array initializer for avoiding other pitfalls.
Fixes: 785b6f29a7 ("ALSA: usb-audio: scarlett2: Fix wrong resume call")
Reported-by: Pavel Machek <pavel@denx.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210714084836.1977-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 463f36c76f upstream.
The DMA code section of the decompressor must be compiled with expolines
if Spectre V2 mitigation has been enabled for the decompressed kernel.
This is required because although the decompressor's image contains
the DMA code section, it is handed over to the decompressed kernel for use.
Because the DMA code is already slow w/o expolines, use expolines always
regardless whether the decompressed kernel is using them or not. This
simplifies the DMA code by dropping the conditional compilation of
expolines.
Fixes: bf72630130 ("s390: use proper expoline sections for .dma code")
Cc: <stable@vger.kernel.org> # 5.2
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10252bae86 upstream.
There's a chance that the IDA allocated in mmc_alloc_host() is not freed
for some time because it's freed as part of a class' release function
(see mmc_host_classdev_release() where the IDA is freed). If another
thread is holding a reference to the class, then only once all balancing
device_put() calls (in turn calling kobject_put()) have been made will
the IDA be released and usable again.
Normally this isn't a problem because the kobject is released before
anything else that may want to use the same number tries to again, but
with CONFIG_DEBUG_KOBJECT_RELEASE=y and OF aliases it becomes pretty
easy to try to allocate an alias from the IDA twice while the first time
it was allocated is still pending a call to ida_simple_remove(). It's
also possible to trigger it by using CONFIG_DEBUG_KOBJECT_RELEASE and
probe defering a driver at boot that calls mmc_alloc_host() before
trying to get resources that may defer likes clks or regulators.
Instead of allocating from the IDA in this scenario, let's just skip it
if we know this is an OF alias. The number is already "claimed" and
devices that aren't using OF aliases won't try to use the claimed
numbers anyway (see mmc_first_nonreserved_index()). This should avoid
any issues with mmc_alloc_host() returning failures from the
ida_simple_get() in the case that we're using an OF alias.
Cc: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Cc: Sujit Kautkar <sujitka@chromium.org>
Reported-by: Zubin Mithra <zsm@chromium.org>
Fixes: fa2d0aa969 ("mmc: core: Allow setting slot index via device tree alias")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210623075002.1746924-3-swboyd@chromium.org
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 488968a894 ]
Remove the conditional checking for out_data_len and skipping the fallocate
if it is 0. This is wrong will actually change any legitimate the fallocate
where the entire region is unallocated into a no-op.
Additionally, before allocating the range, if FALLOC_FL_KEEP_SIZE is set then
we need to clamp the length of the fallocate region as to not extend the size of the file.
Fixes: 966a3cb7c7 ("cifs: improve fallocate emulation")
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2485bd7557 ]
We only allow sending single credit writes through the SMB2_write() synchronous
api so split this into smaller chunks.
Fixes: 966a3cb7c7 ("cifs: improve fallocate emulation")
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Reported-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d85a6f44b ]
The 4th parameter in tc_chain_notify() should be flags rather than seq.
Let's change it back correctly.
Fixes: 32a4f5ecd7 ("net: sched: introduce chain object to uapi")
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e40cba9490 ]
This simple series of commands:
ip link add br0 type bridge vlan_filtering 1
ip link set swp0 master br0
fails on sja1105 with the following error:
[ 33.439103] sja1105 spi0.1: vlan-lookup-table needs to have at least the default untagged VLAN
[ 33.447710] sja1105 spi0.1: Invalid config, cannot upload
Warning: sja1105: Failed to change VLAN Ethertype.
For context, sja1105 has 3 operating modes:
- SJA1105_VLAN_UNAWARE: the dsa_8021q_vlans are committed to hardware
- SJA1105_VLAN_FILTERING_FULL: the bridge_vlans are committed to hardware
- SJA1105_VLAN_FILTERING_BEST_EFFORT: both the dsa_8021q_vlans and the
bridge_vlans are committed to hardware
Swapping out a VLAN list and another in happens in
sja1105_build_vlan_table(), which performs a delta update procedure.
That function is called from a few places, notably from
sja1105_vlan_filtering() which is called from the
SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING handler.
The above set of 2 commands fails when run on a kernel pre-commit
8841f6e63f ("net: dsa: sja1105: make devlink property
best_effort_vlan_filtering true by default"). So the priv->vlan_state
transition that takes place is between VLAN-unaware and full VLAN
filtering. So the dsa_8021q_vlans are swapped out and the bridge_vlans
are swapped in.
So why does it fail?
Well, the bridge driver, through nbp_vlan_init(), first sets up the
SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING attribute, and only then
proceeds to call nbp_vlan_add for the default_pvid.
So when we swap out the dsa_8021q_vlans and swap in the bridge_vlans in
the SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING handler, there are no bridge
VLANs (yet). So we have wiped the VLAN table clean, and the low-level
static config checker complains of an invalid configuration. We _will_
add the bridge VLANs using the dynamic config interface, albeit later,
when nbp_vlan_add() calls us. So it is natural that it fails.
So why did it ever work?
Surprisingly, it looks like I only tested this configuration with 2
things set up in a particular way:
- a network manager that brings all ports up
- a kernel with CONFIG_VLAN_8021Q=y
It is widely known that commit ad1afb0039 ("vlan_dev: VLAN 0 should be
treated as "no vlan tag" (802.1p packet)") installs VID 0 to every net
device that comes up. DSA treats these VLANs as bridge VLANs, and
therefore, in my testing, the list of bridge_vlans was never empty.
However, if CONFIG_VLAN_8021Q is not enabled, or the port is not up when
it joins a VLAN-aware bridge, the bridge_vlans list will be temporarily
empty, and the sja1105_static_config_reload() call from
sja1105_vlan_filtering() will fail.
To fix this, the simplest thing is to keep VID 4095, the one used for
CPU-injected control packets since commit ed040abca4 ("net: dsa:
sja1105: use 4095 as the private VLAN for untagged traffic"), in the
list of bridge VLANs too, not just the list of tag_8021q VLANs. This
ensures that the list of bridge VLANs will never be empty.
Fixes: ec5ae61076 ("net: dsa: sja1105: save/restore VLANs using a delta commit method")
Reported-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 213ad73d06 ]
Multiple complaints have been raised from the TFO users on the internet
stating that the TFO blackhole logic is too aggressive and gets falsely
triggered too often.
(e.g. https://blog.apnic.net/2021/07/05/tcp-fast-open-not-so-fast/)
Considering that most middleboxes no longer drop TFO packets, we decide
to disable the blackhole logic by setting
/proc/sys/net/ipv4/tcp_fastopen_blackhole_timeout_set to 0 by default.
Fixes: cf1ef3f071 ("net/tcp_fastopen: Disable active side TFO in certain scenarios")
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58acd10092 ]
syzbot reported a call trace:
BUG: KASAN: use-after-free in sctp_auth_shkey_hold+0x22/0xa0 net/sctp/auth.c:112
Call Trace:
sctp_auth_shkey_hold+0x22/0xa0 net/sctp/auth.c:112
sctp_set_owner_w net/sctp/socket.c:131 [inline]
sctp_sendmsg_to_asoc+0x152e/0x2180 net/sctp/socket.c:1865
sctp_sendmsg+0x103b/0x1d30 net/sctp/socket.c:2027
inet_sendmsg+0x99/0xe0 net/ipv4/af_inet.c:821
sock_sendmsg_nosec net/socket.c:703 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:723
This is an use-after-free issue caused by not updating asoc->shkey after
it was replaced in the key list asoc->endpoint_shared_keys, and the old
key was freed.
This patch is to fix by also updating active_key for asoc when old key is
being replaced with a new one. Note that this issue doesn't exist in
sctp_auth_del_key_id(), as it's not allowed to delete the active_key
from the asoc.
Fixes: 1b1e0bc994 ("sctp: add refcnt support for sh_key")
Reported-by: syzbot+b774577370208727d12b@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aaeb7bb061 ]
When using Write Zeroes on a namespace that has protection
information enabled they behavior without the PRACT bit
counter-intuitive and will generally lead to validation failures
when reading the written blocks. Fix this by always setting the
PRACT bit that generates matching PI data on the fly.
Fixes: 6e02318eae ("nvme: add support for the Write Zeroes command")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e9a72f874d ]
When registering the MDIO bus for a r8169 device, we use the PCI
bus/device specifier as a (seemingly) unique device identifier.
However the very same BDF number can be used on another PCI segment,
which makes the driver fail probing:
[ 27.544136] r8169 0002:07:00.0: enabling device (0000 -> 0003)
[ 27.559734] sysfs: cannot create duplicate filename '/class/mdio_bus/r8169-700'
....
[ 27.684858] libphy: mii_bus r8169-700 failed to register
[ 27.695602] r8169: probe of 0002:07:00.0 failed with error -22
Add the segment number to the device name to make it more unique.
This fixes operation on ARM N1SDP boards, with two boards connected
together to form an SMP system, and all on-board devices showing up
twice, just on different PCI segments. A similar issue would occur on
large systems with many PCI slots and multiple RTL8169 NICs.
Fixes: f1e911d5d0 ("r8169: add basic phylib support")
Signed-off-by: Sayanta Pattanayak <sayanta.pattanayak@arm.com>
[Andre: expand commit message, use pci_domain_nr()]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c881ca0b3 ]
To quote Alexey[1]:
I was adding custom tracepoint to the kernel, grabbed full F34 kernel
.config, disabled modules and booted whole shebang as VM kernel.
Then did
perf record -a -e ...
It crashed:
general protection fault, probably for non-canonical address 0x435f5346592e4243: 0000 [#1] SMP PTI
CPU: 1 PID: 842 Comm: cat Not tainted 5.12.6+ #26
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-1.fc33 04/01/2014
RIP: 0010:t_show+0x22/0xd0
Then reproducer was narrowed to
# cat /sys/kernel/tracing/printk_formats
Original F34 kernel with modules didn't crash.
So I started to disable options and after disabling AFS everything
started working again.
The root cause is that AFS was placing char arrays content into a
section full of _pointers_ to strings with predictable consequences.
Non canonical address 435f5346592e4243 is "CB.YFS_" which came from
CM_NAME macro.
Steps to reproduce:
CONFIG_AFS=y
CONFIG_TRACING=y
# cat /sys/kernel/tracing/printk_formats
Fix this by the following means:
(1) Add enum->string translation tables in the event header with the AFS
and YFS cache/callback manager operations listed by RPC operation ID.
(2) Modify the afs_cb_call tracepoint to print the string from the
translation table rather than using the string at the afs_call name
pointer.
(3) Switch translation table depending on the service we're being accessed
as (AFS or YFS) in the tracepoint print clause. Will this cause
problems to userspace utilities?
Note that the symbolic representation of the YFS service ID isn't
available to this header, so I've put it in as a number. I'm not sure
if this is the best way to do this.
(4) Remove the name wrangling (CM_NAME) macro and put the names directly
into the afs_call_type structs in cmservice.c.
Fixes: 8e8d7f13b6 ("afs: Add some tracepoints")
Reported-by: Alexey Dobriyan (SK hynix) <adobriyan@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
cc: Andrew Morton <akpm@linux-foundation.org>
cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/r/YLAXfvZ+rObEOdc%2F@localhost.localdomain/ [1]
Link: https://lore.kernel.org/r/643721.1623754699@warthog.procyon.org.uk/
Link: https://lore.kernel.org/r/162430903582.2896199.6098150063997983353.stgit@warthog.procyon.org.uk/ # v1
Link: https://lore.kernel.org/r/162609463957.3133237.15916579353149746363.stgit@warthog.procyon.org.uk/ # v1 (repost)
Link: https://lore.kernel.org/r/162610726860.3408253.445207609466288531.stgit@warthog.procyon.org.uk/ # v2
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3a1a937f7 ]
This reverts commit 0bd860493f.
While the patch was working as stated,ie preventing the L850-GL LTE modem
from crashing on some U3 wake-ups due to a race condition between the
host wake-up and the modem-side wake-up, when using the MBIM interface,
this would force disabling the USB runtime PM on the device.
The increased power consumption is significant for LTE laptops,
and given that with decently recent modem firmwares, when the modem hits
the bug, it automatically recovers (ie it drops from the bus, but
automatically re-enumerates after less than half a second, rather than being
stuck until a power cycle as it was doing with ancient firmware), for
most people, the trade-off now seems in favor of re-enabling it by
default.
For people with access to the platform code, the bug can also be worked-around
successfully by changing the USB3 LFPM polling off-time for the XHCI
controller in the BIOS code.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Link: https://lore.kernel.org/r/20210721092516.2775971-1-vpalatin@chromium.org
Fixes: 0bd860493f ("USB: quirks: ignore remote wake-up on Fibocom L850-GL LTE modem")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdb330f4b4 ]
If MDSs aren't available while mounting a filesystem, the session state
will transition from SESSION_OPENING to SESSION_CLOSING. And in that
scenario check_session_state() will be called from delayed_work() and
trigger this WARN.
Avoid this by only WARNing after a session has already been established
(i.e., the s_ttl will be different from 0).
Fixes: 62575e270f ("ceph: check session state after bumping session->s_seq")
Signed-off-by: Luis Henriques <lhenriques@suse.de>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8fb4792f09 ]
While running the self-tests on a KASAN enabled kernel, I observed a
slab-out-of-bounds splat very similar to the one reported in
commit 821bbf79fe ("ipv6: Fix KASAN: slab-out-of-bounds Read in
fib6_nh_flush_exceptions").
We additionally need to take care of fib6_metrics initialization
failure when the caller provides an nh.
The fix is similar, explicitly free the route instead of calling
fib6_info_release on a half-initialized object.
Fixes: f88d8ea67f ("ipv6: Plumb support for nexthop object in a fib6_info")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 727d6a8b7e ]
Currently tcf_skbmod_act() assumes that packets use Ethernet as their L2
protocol, which is not always the case. As an example, for CAN devices:
$ ip link add dev vcan0 type vcan
$ ip link set up vcan0
$ tc qdisc add dev vcan0 root handle 1: htb
$ tc filter add dev vcan0 parent 1: protocol ip prio 10 \
matchall action skbmod swap mac
Doing the above silently corrupts all the packets. Do not perform skbmod
actions for non-Ethernet packets.
Fixes: 86da71b573 ("net_sched: Introduce skbmod action")
Reviewed-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Peilin Ye <peilin.ye@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bbfd4506f9 ]
Currently, VF doesn't enable rx VLAN offload when initializating,
and PF does it for VFs. If user disable the rx VLAN offload for
VF with ethtool -K, and reload the VF driver, it may cause the
rx VLAN offload state being inconsistent between hardware and
software.
Fixes it by enabling rx VLAN offload when VF initializing.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b713d14dc ]
Currently, the mailbox synchronous communication between VF and PF use
the following fields to maintain communication:
1. Origin_mbx_msg which was combined by message code and subcode, used
to match request and response.
2. Received_resp which means whether received response.
There may possible mismatches of the following situation:
1. VF sends message A with code=1 subcode=1.
2. PF was blocked about 500ms when processing the message A.
3. VF will detect message A timeout because it can't get the response
within 500ms.
4. VF sends message B with code=1 subcode=1 which equal message A.
5. PF processes the first message A and send the response message to
VF.
6. VF will identify the response matched the message B because the
code/subcode is the same. This will lead to mismatch of request and
response.
To fix the above bug, we use the following scheme:
1. The message sent from VF was labelled with match_id which was a
unique 16-bit non-zero value.
2. The response sent from PF will label with match_id which got from
the request.
3. The VF uses the match_id to match request and response message.
As for PF driver, it only needs to copy the match_id from request to
response.
Fixes: dde1a86e93 ("net: hns3: Add mailbox support to PF driver")
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f20c8adb1 ]
tfo_active_disable_stamp is read and written locklessly.
We need to annotate these accesses appropriately.
Then, we need to perform the atomic_inc(tfo_active_disable_times)
after the timestamp has been updated, and thus add barriers
to make sure tcp_fastopen_active_should_disable() wont read
a stale timestamp.
Fixes: cf1ef3f071 ("net/tcp_fastopen: Disable active side TFO in certain scenarios")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Wei Wang <weiwan@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b16f3299ae ]
Building on ARCH=arc causes a "redefined" warning, so rename this
driver's CACHE_LINE_MASK to avoid the warning.
../drivers/net/ethernet/hisilicon/hip04_eth.c:134: warning: "CACHE_LINE_MASK" redefined
134 | #define CACHE_LINE_MASK 0x3F
In file included from ../include/linux/cache.h:6,
from ../include/linux/printk.h:9,
from ../include/linux/kernel.h:19,
from ../include/linux/list.h:9,
from ../include/linux/module.h:12,
from ../drivers/net/ethernet/hisilicon/hip04_eth.c:7:
../arch/arc/include/asm/cache.h:17: note: this is the location of the previous definition
17 | #define CACHE_LINE_MASK (~(L1_CACHE_BYTES - 1))
Fixes: d413779cdd ("net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11a39259ff ]
bnxt_half_open_nic() is called during during ethtool self test and is
protected by rtnl_lock. Firmware reset can be happening at the same
time. Only critical portions of the entire firmware reset sequence
are protected by the rtnl_lock. It is possible that bnxt_half_open_nic()
can be called when the firmware reset sequence is aborting. In that
case, bnxt_half_open_nic() needs to check if the ABORT_ERR flag is set
and abort if it is. The ethtool self test will fail but the NIC will be
brought to a consistent IF_DOWN state.
Without this patch, if bnxt_half_open_nic() were to continue in this
error state, it may crash like this:
bnxt_en 0000:82:00.1 enp130s0f1np1: FW reset in progress during close, FW reset will be aborted
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
...
Process ethtool (pid: 333327, stack limit = 0x0000000046476577)
Call trace:
bnxt_alloc_mem+0x444/0xef0 [bnxt_en]
bnxt_half_open_nic+0x24/0xb8 [bnxt_en]
bnxt_self_test+0x2dc/0x390 [bnxt_en]
ethtool_self_test+0xe0/0x1f8
dev_ethtool+0x1744/0x22d0
dev_ioctl+0x190/0x3e0
sock_ioctl+0x238/0x480
do_vfs_ioctl+0xc4/0x758
ksys_ioctl+0x84/0xb8
__arm64_sys_ioctl+0x28/0x38
el0_svc_handler+0xb0/0x180
el0_svc+0x8/0xc
Fixes: a1301f08c5 ("bnxt_en: Check abort error state in bnxt_open_nic().")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 96bdd4b9ea ]
Only pass supported VLAN protocol IDs for stripped VLAN tags to the
stack. The stack will hit WARN() if the protocol ID is unsupported.
Existing firmware sets up the chip to strip 0x8100, 0x88a8, 0x9100.
Only the 1st two protocols are supported by the kernel.
Fixes: a196e96bb6 ("bnxt_en: clean up VLAN feature bit handling")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6cd657cb3e ]
In the BNXT_FW_RESET_STATE_POLL_VF state in bnxt_fw_reset_task() after all
VFs have unregistered, we need to check for BNXT_STATE_ABORT_ERR after
we acquire the rtnl_lock. If the flag is set, we need to abort.
Fixes: 230d1f0de7 ("bnxt_en: Handle firmware reset.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c9f046bc3 ]
The capabilities can change after firmware upgrade/downgrade, so we
should get the up-to-date RoCE capabilities everytime bnxt_ulp_probe()
is called.
Fixes: 2151fe0830 ("bnxt_en: Handle RESET_NOTIFY async event from firmware.")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c81cfb6256 ]
If device is already disabled in reset path and PCI io error is
detected before the device could be enabled, driver could
call pci_disable_device() for already disabled device. Fix this
problem by calling pci_disable_device() only if the device is already
enabled.
Fixes: 6316ea6db9 ("bnxt_en: Enable AER support.")
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d2cbbf1fe5 ]
During a rework of initramfs code the INITRAMFS_COMPRESSION config
option was removed in commit 65e00e04e5. A leftover as a dependency
broke the config option ACPI_TABLE_OVERRIDE_VIA_ BUILTIN_INITRD that
is used to enable the overriding of ACPI tables from built-in initrd.
Fixing the dependency.
Fixes: 65e00e04e5 ("initramfs: refactor the initramfs build rules")
Signed-off-by: Robert Richter <rrichter@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56912da7a6 ]
The original implementation of RPM handling in probe() was mostly
correct, except it failed to call pm_runtime_get_*() to activate the
hardware. The subsequent fix, 734882a8bf ("spi: cadence: Correct
initialisation of runtime PM"), breaks the implementation further,
to the point where the system using this hard IP on ZynqMP hangs on
boot, because it accesses hardware which is gated off.
Undo 734882a8bf ("spi: cadence: Correct initialisation of runtime
PM") and instead add missing pm_runtime_get_noresume() and move the
RPM disabling all the way to the end of probe(). That makes ZynqMP
not hang on boot yet again.
Fixes: 734882a8bf ("spi: cadence: Correct initialisation of runtime PM")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Charles Keepax <ckeepax@opensource.cirrus.com>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210716182133.218640-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e746f3451e ]
A ISCSI_IFACE_PARAM can have the same value as a ISCSI_NET_PARAM so when
iscsi_iface_attr_is_visible tries to figure out the type by just checking
the value, we can collide and return the wrong type. When we call into the
driver we might not match and return that we don't want attr visible in
sysfs. The patch fixes this by setting the type when we figure out what the
param is.
Link: https://lore.kernel.org/r/20210701002559.89533-1-michael.christie@oracle.com
Fixes: 3e0f65b34c ("[SCSI] iscsi_transport: Additional parameters for network settings")
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 517a16b1a8 ]
Commit 63346650c1 ("netrom: switch to sock timer API") switched to use
sock timer API. It replaces mod_timer() by sk_reset_timer(), and
del_timer() by sk_stop_timer().
Function sk_reset_timer() will increase the refcount of sock if it is
called on an inactive timer, hence, in case the timer expires, we need to
decrease the refcount ourselves in the handler, otherwise, the sock
refcount will be unbalanced and the sock will never be freed.
Signed-off-by: Nguyen Dinh Phi <phind.uet@gmail.com>
Reported-by: syzbot+10f1194569953b72f1ae@syzkaller.appspotmail.com
Fixes: 63346650c1 ("netrom: switch to sock timer API")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f3fdd8d48 ]
After commit ca84bd058d ("sctp: copy the optval from user space in
sctp_setsockopt"), it does memory allocation in sctp_setsockopt with
the optlen, and it would fail the allocation and return error if the
optlen from user space is a huge value.
This breaks some sockopts, like SCTP_HMAC_IDENT, SCTP_RESET_STREAMS and
SCTP_AUTH_KEY, as when processing these sockopts before, optlen would
be trimmed to a biggest value it needs when optlen is a huge value,
instead of failing the allocation and returning error.
This patch is to fix the allocation failure when it's a huge optlen from
user space by trimming it to the biggest size sctp sockopt may need when
necessary, and this biggest size is from sctp_setsockopt_reset_streams()
for SCTP_RESET_STREAMS, which is bigger than those for SCTP_HMAC_IDENT
and SCTP_AUTH_KEY.
Fixes: ca84bd058d ("sctp: copy the optval from user space in sctp_setsockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5051bcece ]
Syzbot reported memory leak in tcindex_set_parms(). The problem was in
non-freed perfect hash in tcindex_partial_destroy_work().
In tcindex_set_parms() new tcindex_data is allocated and some fields from
old one are copied to new one, but not the perfect hash. Since
tcindex_partial_destroy_work() is the destroy function for old
tcindex_data, we need to free perfect hash to avoid memory leak.
Reported-and-tested-by: syzbot+f0bbb2287b8993d4fa74@syzkaller.appspotmail.com
Fixes: 331b72922c ("net: sched: RCU cls_tcindex")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd31ecf44b ]
When running CPU_FTR_P9_TM_HV_ASSIST, HFSCR[TM] is set for the guest
even if the host has CONFIG_TRANSACTIONAL_MEM=n, which causes it to be
unprepared to handle guest exits while transactional.
Normal guests don't have a problem because the HTM capability will not
be advertised, but a rogue or buggy one could crash the host.
Fixes: 4bb3c7a020 ("KVM: PPC: Book3S HV: Work around transactional memory bugs in POWER9")
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210716024310.164448-1-npiggin@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f119ba1d5 ]
The release_sock() is blocking function, it would change the state
after sleeping. use wait_woken() instead.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 674a9f1f68 ]
Missing TPM final event log table is not a firmware bug.
Clearly if providing event log in the old format makes the final event
log invalid it should not be provided at least in that case.
Fixes: b4f1874c62 ("tpm: check event log version before reading final events")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 40ac971eab ]
xen-swiotlb can use vmalloc backed addresses for dma coherent allocations
and uses the common helpers. Properly handle them to unbreak Xen on
ARM platforms.
Fixes: 1b65c4e5a9 ("swiotlb-xen: use xen_alloc/free_coherent_pages")
Signed-off-by: Roman Skakun <roman_skakun@epam.com>
Reviewed-by: Andrii Anisov <andrii_anisov@epam.com>
[hch: split the patch, renamed the helpers]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 991e634360 ]
When nr_segs equal to zero in iovec_from_user, the object
msg->msg_iter.iov is uninit stack memory in caif_seqpkt_sendmsg
which is defined in ___sys_sendmsg. So we cann't just judge
msg->msg_iter.iov->base directlly. We can use nr_segs to judge
msg in caif_seqpkt_sendmsg whether has data buffers.
=====================================================
BUG: KMSAN: uninit-value in caif_seqpkt_sendmsg+0x693/0xf60 net/caif/caif_socket.c:542
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1c9/0x220 lib/dump_stack.c:118
kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:118
__msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:215
caif_seqpkt_sendmsg+0x693/0xf60 net/caif/caif_socket.c:542
sock_sendmsg_nosec net/socket.c:652 [inline]
sock_sendmsg net/socket.c:672 [inline]
____sys_sendmsg+0x12b6/0x1350 net/socket.c:2343
___sys_sendmsg net/socket.c:2397 [inline]
__sys_sendmmsg+0x808/0xc90 net/socket.c:2480
__compat_sys_sendmmsg net/compat.c:656 [inline]
Reported-by: syzbot+09a5d591c1f98cf5efcb@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?id=1ace85e8fc9b0d5a45c08c2656c3e91762daa9b8
Fixes: bece7b2398 ("caif: Rewritten socket implementation")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54ea2f49fd ]
The proc socket stats use sk_prot->inuse_idx value to record inuse sock
stats. We currently do not set this correctly from sockmap side. The
result is reading sock stats '/proc/net/sockstat' gives incorrect values.
The socket counter is incremented correctly, but because we don't set the
counter correctly when we replace sk_prot we may omit the decrement.
To get the correct inuse_idx value move the core_initcall that initializes
the UDP proto handlers to late_initcall. This way it is initialized after
UDP has the chance to assign the inuse_idx value from the register protocol
handler.
Fixes: edc6741cc6 ("bpf: Add sockmap hooks for UDP sockets")
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Cong Wang <cong.wang@bytedance.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20210714154750.528206-1-jakub@cloudflare.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 228a4a7ba8 ]
The proc socket stats use sk_prot->inuse_idx value to record inuse sock
stats. We currently do not set this correctly from sockmap side. The
result is reading sock stats '/proc/net/sockstat' gives incorrect values.
The socket counter is incremented correctly, but because we don't set the
counter correctly when we replace sk_prot we may omit the decrement.
To get the correct inuse_idx value move the core_initcall that initializes
the TCP proto handlers to late_initcall. This way it is initialized after
TCP has the chance to assign the inuse_idx value from the register protocol
handler.
Fixes: 604326b41a ("bpf, sockmap: convert to generic sk_msg interface")
Suggested-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Cong Wang <cong.wang@bytedance.com>
Link: https://lore.kernel.org/bpf/20210712195546.423990-3-john.fastabend@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9109165625 ]
Currently array jit->seen_reg[r1] is being accessed before the range
checking of index r1. The range changing on r1 should be performed
first since it will avoid any potential out-of-range accesses on the
array seen_reg[] and also it is more optimal to perform checks on r1
before fetching data from the array. Fix this by swapping the order
of the checks before the array access.
Fixes: 0546231057 ("s390/bpf: Add s390x eBPF JIT compiler backend")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Ilya Leoshkevich <iii@linux.ibm.com>
Acked-by: Ilya Leoshkevich <iii@linux.ibm.com>
Link: https://lore.kernel.org/bpf/20210715125712.24690-1-colin.king@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e7efc2ce3d ]
Shifting the u16 integer oct->pcie_port by CN23XX_PKT_INPUT_CTL_MAC_NUM_POS
(29) bits will be promoted to a 32 bit signed int and then sign-extended
to a u64. In the cases where oct->pcie_port where bit 2 is set (e.g. 3..7)
the shifted value will be sign extended and the top 32 bits of the result
will be set.
Fix this by casting the u16 values to a u64 before the 29 bit left shift.
Addresses-Coverity: ("Unintended sign extension")
Fixes: 3451b97cce ("liquidio: CN23XX register setup")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aebacb7f6c ]
31cd0e119d ("timers: Recalculate next timer interrupt only when
necessary") subtly altered get_next_timer_interrupt()'s behaviour. The
function no longer consistently returns KTIME_MAX with no timers
pending.
In order to decide if there are any timers pending we check whether the
next expiry will happen NEXT_TIMER_MAX_DELTA jiffies from now.
Unfortunately, the next expiry time and the timer base clock are no
longer updated in unison. The former changes upon certain timer
operations (enqueue, expire, detach), whereas the latter keeps track of
jiffies as they move forward. Ultimately breaking the logic above.
A simplified example:
- Upon entering get_next_timer_interrupt() with:
jiffies = 1
base->clk = 0;
base->next_expiry = NEXT_TIMER_MAX_DELTA;
'base->next_expiry == base->clk + NEXT_TIMER_MAX_DELTA', the function
returns KTIME_MAX.
- 'base->clk' is updated to the jiffies value.
- The next time we enter get_next_timer_interrupt(), taking into account
no timer operations happened:
base->clk = 1;
base->next_expiry = NEXT_TIMER_MAX_DELTA;
'base->next_expiry != base->clk + NEXT_TIMER_MAX_DELTA', the function
returns a valid expire time, which is incorrect.
This ultimately might unnecessarily rearm sched's timer on nohz_full
setups, and add latency to the system[1].
So, introduce 'base->timers_pending'[2], update it every time
'base->next_expiry' changes, and use it in get_next_timer_interrupt().
[1] See tick_nohz_stop_tick().
[2] A quick pahole check on x86_64 and arm64 shows it doesn't make
'struct timer_base' any bigger.
Fixes: 31cd0e119d ("timers: Recalculate next timer interrupt only when necessary")
Signed-off-by: Nicolas Saenz Julienne <nsaenzju@redhat.com>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c71f78a662 ]
The ALC5631 does not like multi-write accesses, avoid them. This fixes:
rt5631 4-001a: Unable to sync registers 0x3a-0x3c. -121
errors on resume from suspend (and all registers after the registers in
the error not being synced).
Inspired by commit 2d30e9494f ("ASoC: rt5651: Fix regcache sync errors
on resume") from Hans de Geode, which fixed the same errors on ALC5651.
Signed-off-by: Maxim Schwalm <maxim.schwalm@gmail.com>
Link: https://lore.kernel.org/r/20210712005011.28536-1-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c73daee4b ]
Since config.dev = pdev->dev.parent in current code, so
dev_get_drvdata(rdev->dev.parent) call in hi6421_regulator_enable
returns the drvdata of the mfd device rather than the regulator. Fix it.
This was broken while converting to use simplified DT parsing because the
config.dev changed from pdev->dev to pdev->dev.parent for parsing the
parent's of_node.
Fixes: 29dc269a85 ("regulator: hi6421: Convert to use simplified DT parsing")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20210630095959.2411543-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7999d2555c ]
Add pm_runtime calls in probe/probe error path and remove
in order to be consistent in all places in ordering and
ensure that pm_runtime is disabled prior to resources used
by the SPI controller.
This patch also fixes the 2 following warnings on driver remove:
WARNING: CPU: 0 PID: 743 at drivers/clk/clk.c:594 clk_core_disable_lock+0x18/0x24
WARNING: CPU: 0 PID: 743 at drivers/clk/clk.c:476 clk_unprepare+0x24/0x2c
Fixes: 038ac869c9 ("spi: stm32: add runtime PM support")
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://lore.kernel.org/r/1625646426-5826-2-git-send-email-alain.volmat@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0f008551f ]
The tracepoints trace_sched_stat_{wait, sleep, iowait} are not exposed to user
if CONFIG_SCHEDSTATS is not set, "perf sched record" records the three events.
As a result, the command fails.
Before:
#perf sched record sleep 1
event syntax error: 'sched:sched_stat_wait'
\___ unknown tracepoint
Error: File /sys/kernel/tracing/events/sched/sched_stat_wait not found.
Hint: Perhaps this kernel misses some CONFIG_ setting to enable this feature?.
Run 'perf list' for a list of valid events
Usage: perf record [<options>] [<command>]
or: perf record [<options>] -- <command> [<options>]
-e, --event <event> event selector. use 'perf list' to list available events
Solution:
Check whether schedstat tracepoints are exposed. If no, these events are not recorded.
After:
# perf sched record sleep 1
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.163 MB perf.data (1091 samples) ]
# perf sched report
run measurement overhead: 4736 nsecs
sleep measurement overhead: 9059979 nsecs
the run test took 999854 nsecs
the sleep test took 8945271 nsecs
nr_run_events: 716
nr_sleep_events: 785
nr_wakeup_events: 0
...
------------------------------------------------------------
Fixes: 2a09b5de23 ("sched/fair: do not expose some tracepoints to user if CONFIG_SCHEDSTATS is not set")
Signed-off-by: Yang Jihong <yangjihong1@huawei.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Yafang Shao <laoar.shao@gmail.com>
Link: http://lore.kernel.org/lkml/20210713112358.194693-1-yangjihong1@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7234c362cc ]
The AMD platform does not support the functions Ah CPUID leaf. The returned
results for this entry should all remain zero just like the native does:
AMD host:
0x0000000a 0x00: eax=0x00000000 ebx=0x00000000 ecx=0x00000000 edx=0x00000000
(uncanny) AMD guest:
0x0000000a 0x00: eax=0x00000000 ebx=0x00000000 ecx=0x00000000 edx=0x00008000
Fixes: cadbaa039b ("perf/x86/intel: Make anythread filter support conditional")
Signed-off-by: Like Xu <likexu@tencent.com>
Message-Id: <20210628074354.33848-1-likexu@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 251ef6f71b ]
nvme_dev_remove_admin could free dev->admin_q and the admin_tagset
while they are being accessed by nvme_dev_disable(), which can be called
by nvme_reset_work via nvme_remove_dead_ctrl.
Commit cb4bfda62a ("nvme-pci: fix hot removal during error handling")
intended to avoid requests being stuck on a removed controller by killing
the admin queue. But the later fix c8e9e9b764 ("nvme-pci: unquiesce
admin queue on shutdown"), together with nvme_dev_disable(dev, true)
right before nvme_dev_remove_admin() could help dispatch requests and
fail them early, so we don't need nvme_dev_remove_admin() any more.
Fixes: cb4bfda62a ("nvme-pci: fix hot removal during error handling")
Signed-off-by: Casey Chen <cachen@purestorage.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 015fe6fd29 ]
IRQs are requested during driver's ndo_open() and then later
freed up in disable_interrupts() during driver unload.
A race exists where driver can set the CXGB4_FULL_INIT_DONE
flag in ndo_open() after the disable_interrupts() in driver
unload path checks it, and hence misses calling free_irq().
Fix by unregistering netdevice first and sync with driver's
ndo_open(). This ensures disable_interrupts() checks the flag
correctly and frees up the IRQs properly.
Fixes: b37987e8db ("cxgb4: Disable interrupts and napi before unregistering netdev")
Signed-off-by: Shahjada Abul Husain <shahjada@chelsio.com>
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65e2e6c1c2 ]
As the last call to sprd_pwm_apply() might have exited early if
state->enabled was false, the values for period and duty_cycle stored in
pwm->state might not have been written to hardware and it must be
ensured that they are configured before enabling the PWM.
Fixes: 8aae4b02e8 ("pwm: sprd: Add Spreadtrum PWM support")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e02bf5de4 ]
After redirecting, it's already a new path. So the old PMTU info should
be cleared. The IPv6 test "mtu exception plus redirect" should only
has redirect info without old PMTU.
The IPv4 test can not be changed because of legacy.
Fixes: ec81053528 ("selftests: Add redirect tests")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24b671aad4 ]
If the kernel doesn't enable option CONFIG_IPV6_SUBTREES, the RTA_SRC
info will not be exported to userspace in rt6_fill_node(). And ip cmd will
not print "from ::" to the route output. So remove this check.
Fixes: ec81053528 ("selftests: Add redirect tests")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eca81f0914 ]
The "plat->phy_interface" variable is an enum and in this context GCC
will treat it as an unsigned int so the error handling is never
triggered.
Fixes: b9f0b2f634 ("net: stmmac: platform: fix probe for ACPI devices")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ccd27f05ae ]
The goal of commit df789fe752 ("ipv6: Provide ipv6 version of
"disable_policy" sysctl") was to have the disable_policy from ipv4
available on ipv6.
However, it's not exactly the same mechanism. On IPv4, all packets coming
from an interface, which has disable_policy set, bypass the policy check.
For ipv6, this is done only for local packets, ie for packets destinated to
an address configured on the incoming interface.
Let's align ipv6 with ipv4 so that the 'disable_policy' sysctl has the same
effect for both protocols.
My first approach was to create a new kind of route cache entries, to be
able to set DST_NOPOLICY without modifying routes. This would have added a
lot of code. Because the local delivery path is already handled, I choose
to focus on the forwarding path to minimize code churn.
Fixes: df789fe752 ("ipv6: Provide ipv6 version of "disable_policy" sysctl")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 168e696a36 ]
bond_ipsec_offload_ok() is called to check whether the interface supports
ipsec offload or not.
bonding interface support ipsec offload only in active-backup mode.
So, if a bond interface is not in active-backup mode, it should return
false but it returns true.
Fixes: a3b658cfb6 ("bonding: allow xfrm offload setup post-module-load")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a5605505d ]
bonding has been supporting ipsec offload.
When SA is added, bonding just passes SA to its own active real interface.
But it doesn't manage SA.
So, when events(add/del real interface, active real interface change, etc)
occur, bonding can't handle that well because It doesn't manage SA.
So some problems(panic, UAF, refcnt leak)occur.
In order to make it stable, it should manage SA.
That's the reason why struct bond_ipsec is added.
When a new SA is added to bonding interface, it is stored in the
bond_ipsec list. And the SA is passed to a current active real interface.
If events occur, it uses bond_ipsec data to handle these events.
bond->ipsec_list is protected by bond->ipsec_lock.
If a current active real interface is changed, the following logic works.
1. delete all SAs from old active real interface
2. Add all SAs to the new active real interface.
3. If a new active real interface doesn't support ipsec offload or SA's
option, it sets real_dev to NULL.
Fixes: 18cb261afd ("bonding: support hardware encryption offload to slaves")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b121693381 ]
bonding interface can be nested and it supports ipsec offload.
So, it allows setting the nested bonding + ipsec scenario.
But code does not support this scenario.
So, it should be disallowed.
interface graph:
bond2
|
bond1
|
eth0
The nested bonding + ipsec offload may not a real usecase.
So, disallowing this scenario is fine.
Fixes: 18cb261afd ("bonding: support hardware encryption offload to slaves")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a22c39b831 ]
To dereference bond->curr_active_slave, it uses rcu_dereference().
But it and the caller doesn't acquire RCU so a warning occurs.
So add rcu_read_lock().
Test commands:
ip netns add A
ip netns exec A bash
modprobe netdevsim
echo "1 1" > /sys/bus/netdevsim/new_device
ip link add bond0 type bond
ip link set eth0 master bond0
ip link set eth0 up
ip link set bond0 up
ip x s add proto esp dst 14.1.1.1 src 15.1.1.1 spi 0x07 mode \
transport reqid 0x07 replay-window 32 aead 'rfc4106(gcm(aes))' \
0x44434241343332312423222114131211f4f3f2f1 128 sel src 14.0.0.52/24 \
dst 14.0.0.70/24 proto tcp offload dev bond0 dir in
ip x s f
Splat looks like:
=============================
WARNING: suspicious RCU usage
5.13.0-rc3+ #1168 Not tainted
-----------------------------
drivers/net/bonding/bond_main.c:448 suspicious rcu_dereference_check()
usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
2 locks held by ip/705:
#0: ffff888106701780 (&net->xfrm.xfrm_cfg_mutex){+.+.}-{3:3},
at: xfrm_netlink_rcv+0x59/0x80 [xfrm_user]
#1: ffff8880075b0098 (&x->lock){+.-.}-{2:2},
at: xfrm_state_delete+0x16/0x30
stack backtrace:
CPU: 6 PID: 705 Comm: ip Not tainted 5.13.0-rc3+ #1168
Call Trace:
dump_stack+0xa4/0xe5
bond_ipsec_del_sa+0x16a/0x1c0 [bonding]
__xfrm_state_delete+0x51f/0x730
xfrm_state_delete+0x1e/0x30
xfrm_state_flush+0x22f/0x390
xfrm_flush_sa+0xd8/0x260 [xfrm_user]
? xfrm_flush_policy+0x290/0x290 [xfrm_user]
xfrm_user_rcv_msg+0x331/0x660 [xfrm_user]
? rcu_read_lock_sched_held+0x91/0xc0
? xfrm_user_state_lookup.constprop.39+0x320/0x320 [xfrm_user]
? find_held_lock+0x3a/0x1c0
? mutex_lock_io_nested+0x1210/0x1210
? sched_clock_cpu+0x18/0x170
netlink_rcv_skb+0x121/0x350
[ ... ]
Fixes: 18cb261afd ("bonding: support hardware encryption offload to slaves")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b648eba4c6 ]
To dereference bond->curr_active_slave, it uses rcu_dereference().
But it and the caller doesn't acquire RCU so a warning occurs.
So add rcu_read_lock().
Test commands:
ip link add dummy0 type dummy
ip link add bond0 type bond
ip link set dummy0 master bond0
ip link set dummy0 up
ip link set bond0 up
ip x s add proto esp dst 14.1.1.1 src 15.1.1.1 spi 0x07 \
mode transport \
reqid 0x07 replay-window 32 aead 'rfc4106(gcm(aes))' \
0x44434241343332312423222114131211f4f3f2f1 128 sel \
src 14.0.0.52/24 dst 14.0.0.70/24 proto tcp offload \
dev bond0 dir in
Splat looks like:
=============================
WARNING: suspicious RCU usage
5.13.0-rc3+ #1168 Not tainted
-----------------------------
drivers/net/bonding/bond_main.c:411 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
1 lock held by ip/684:
#0: ffffffff9a2757c0 (&net->xfrm.xfrm_cfg_mutex){+.+.}-{3:3},
at: xfrm_netlink_rcv+0x59/0x80 [xfrm_user]
55.191733][ T684] stack backtrace:
CPU: 0 PID: 684 Comm: ip Not tainted 5.13.0-rc3+ #1168
Call Trace:
dump_stack+0xa4/0xe5
bond_ipsec_add_sa+0x18c/0x1f0 [bonding]
xfrm_dev_state_add+0x2a9/0x770
? memcpy+0x38/0x60
xfrm_add_sa+0x2278/0x3b10 [xfrm_user]
? xfrm_get_policy+0xaa0/0xaa0 [xfrm_user]
? register_lock_class+0x1750/0x1750
xfrm_user_rcv_msg+0x331/0x660 [xfrm_user]
? rcu_read_lock_sched_held+0x91/0xc0
? xfrm_user_state_lookup.constprop.39+0x320/0x320 [xfrm_user]
? find_held_lock+0x3a/0x1c0
? mutex_lock_io_nested+0x1210/0x1210
? sched_clock_cpu+0x18/0x170
netlink_rcv_skb+0x121/0x350
? xfrm_user_state_lookup.constprop.39+0x320/0x320 [xfrm_user]
? netlink_ack+0x9d0/0x9d0
? netlink_deliver_tap+0x17c/0xa50
xfrm_netlink_rcv+0x68/0x80 [xfrm_user]
netlink_unicast+0x41c/0x610
? netlink_attachskb+0x710/0x710
netlink_sendmsg+0x6b9/0xb70
[ ... ]
Fixes: 18cb261afd ("bonding: support hardware encryption offload to slaves")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6370cc3bbd ]
Remote KCOV coverage collection enables coverage-guided fuzzing of the
code that is not reachable during normal system call execution. It is
especially helpful for fuzzing networking subsystems, where it is
common to perform packet handling in separate work queues even for the
packets that originated directly from the user space.
Enable coverage-guided frame injection by adding kcov remote handle to
skb extensions. Default initialization in __alloc_skb and
__build_skb_around ensures that no socket buffer that was generated
during a system call will be missed.
Code that is of interest and that performs packet processing should be
annotated with kcov_remote_start()/kcov_remote_stop().
An alternative approach is to determine kcov_handle solely on the
basis of the device/interface that received the specific socket
buffer. However, in this case it would be impossible to distinguish
between packets that originated during normal background network
processes or were intentionally injected from the user space.
Signed-off-by: Aleksandr Nogikh <nogikh@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2342ae10d1 ]
If the 'register_netdev() call fails, we must release the resources
allocated by the previous 'gve_init_priv()' call, as already done in the
remove function.
Add a new label and the missing 'gve_teardown_priv_resources()' in the
error handling path.
Fixes: 893ce44df5 ("gve: Add basic driver framework for Compute Engine Virtual NIC")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af30cbd2f4 ]
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: 5eae00c57f ("i40evf: main driver core")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e85e14d68f ]
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: 19ae1b3fb9 ("fm10k: Add support for PCI power management and error handling")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fea03b1ceb ]
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: 40a914fa72 ("igb: Add support for pci-e Advanced Error Reporting")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd2aefcd5e ]
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: 6fabd715e6 ("ixgbe: Implement PCIe AER support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05682a0a61 ]
Static analysis reports this problem
igc_main.c:4944:20: warning: The left operand of '&'
is a garbage value
if (!(phy_data & SR_1000T_REMOTE_RX_STATUS) &&
~~~~~~~~ ^
phy_data is set by the call to igc_read_phy_reg() only if
there is a read_reg() op, else it is unset and a 0 is
returned. Change the return to -EOPNOTSUPP.
Fixes: 208983f099 ("igc: Add watchdog")
Signed-off-by: Tom Rix <trix@redhat.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b292608db ]
Cleans the next descriptor to watch (next_to_watch) when cleaning the
TX ring.
Failure to do so can cause invalid memory accesses. If igb_poll() runs
while the controller is reset this can lead to the driver try to free
a skb that was already freed.
(The crash is harder to reproduce with the igb driver, but the same
potential problem exists as the code is identical to igc)
Fixes: 7cc6fd4c60 ("igb: Don't bother clearing Tx buffer_info in igb_clean_tx_ring")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reported-by: Erez Geva <erez.geva.ext@siemens.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
There are no error exists once device_create has succeeded, and
therefore no need to call device_destroy from vc_mem_init.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
commit f263a81451 upstream.
Subprograms are calling map_poke_track(), but on program release there is no
hook to call map_poke_untrack(). However, on program release, the aux memory
(and poke descriptor table) is freed even though we still have a reference to
it in the element list of the map aux data. When we run map_poke_run(), we then
end up accessing free'd memory, triggering KASAN in prog_array_map_poke_run():
[...]
[ 402.824689] BUG: KASAN: use-after-free in prog_array_map_poke_run+0xc2/0x34e
[ 402.824698] Read of size 4 at addr ffff8881905a7940 by task hubble-fgs/4337
[ 402.824705] CPU: 1 PID: 4337 Comm: hubble-fgs Tainted: G I 5.12.0+ #399
[ 402.824715] Call Trace:
[ 402.824719] dump_stack+0x93/0xc2
[ 402.824727] print_address_description.constprop.0+0x1a/0x140
[ 402.824736] ? prog_array_map_poke_run+0xc2/0x34e
[ 402.824740] ? prog_array_map_poke_run+0xc2/0x34e
[ 402.824744] kasan_report.cold+0x7c/0xd8
[ 402.824752] ? prog_array_map_poke_run+0xc2/0x34e
[ 402.824757] prog_array_map_poke_run+0xc2/0x34e
[ 402.824765] bpf_fd_array_map_update_elem+0x124/0x1a0
[...]
The elements concerned are walked as follows:
for (i = 0; i < elem->aux->size_poke_tab; i++) {
poke = &elem->aux->poke_tab[i];
[...]
The access to size_poke_tab is a 4 byte read, verified by checking offsets
in the KASAN dump:
[ 402.825004] The buggy address belongs to the object at ffff8881905a7800
which belongs to the cache kmalloc-1k of size 1024
[ 402.825008] The buggy address is located 320 bytes inside of
1024-byte region [ffff8881905a7800, ffff8881905a7c00)
The pahole output of bpf_prog_aux:
struct bpf_prog_aux {
[...]
/* --- cacheline 5 boundary (320 bytes) --- */
u32 size_poke_tab; /* 320 4 */
[...]
In general, subprograms do not necessarily manage their own data structures.
For example, BTF func_info and linfo are just pointers to the main program
structure. This allows reference counting and cleanup to be done on the latter
which simplifies their management a bit. The aux->poke_tab struct, however,
did not follow this logic. The initial proposed fix for this use-after-free
bug further embedded poke data tracking into the subprogram with proper
reference counting. However, Daniel and Alexei questioned why we were treating
these objects special; I agree, its unnecessary. The fix here removes the per
subprogram poke table allocation and map tracking and instead simply points
the aux->poke_tab pointer at the main programs poke table. This way, map
tracking is simplified to the main program and we do not need to manage them
per subprogram.
This also means, bpf_prog_free_deferred(), which unwinds the program reference
counting and kfrees objects, needs to ensure that we don't try to double free
the poke_tab when free'ing the subprog structures. This is easily solved by
NULL'ing the poke_tab pointer. The second detail is to ensure that per
subprogram JIT logic only does fixups on poke_tab[] entries it owns. To do
this, we add a pointer in the poke structure to point at the subprogram value
so JITs can easily check while walking the poke_tab structure if the current
entry belongs to the current program. The aux pointer is stable and therefore
suitable for such comparison. On the jit_subprogs() error path, we omit
cleaning up the poke->aux field because these are only ever referenced from
the JIT side, but on error we will never make it to the JIT, so its fine to
leave them dangling. Removing these pointers would complicate the error path
for no reason. However, we do need to untrack all poke descriptors from the
main program as otherwise they could race with the freeing of JIT memory from
the subprograms. Lastly, a748c6975d ("bpf: propagate poke descriptors to
subprograms") had an off-by-one on the subprogram instruction index range
check as it was testing 'insn_idx >= subprog_start && insn_idx <= subprog_end'.
However, subprog_end is the next subprogram's start instruction.
Fixes: a748c6975d ("bpf: propagate poke descriptors to subprograms")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Co-developed-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210707223848.14580-2-john.fastabend@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d719254c1 upstream.
make[2]: *** No rule to make target 'install'. Stop.
make[1]: *** [Makefile:122: runqslower_install] Error 2
make: *** [Makefile:116: bpf_install] Error 2
There is no rule for target 'install' in tools/bpf/runqslower/Makefile,
and there is no need to install it, so just remove 'runqslower_install'.
Fixes: 9c01546d26 ("tools/bpf: Add runqslower tool to tools/bpf")
Signed-off-by: Wei Li <liwei391@huawei.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210628030409.3459095-1-liwei391@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 358ed62420 upstream.
sk_wmem_schedule makes sure that sk_forward_alloc has enough
bytes for charging that is going to be done by sk_mem_charge.
In the transmit zerocopy path, there is sk_mem_charge but there was
no call to sk_wmem_schedule. This change adds that call.
Without this call to sk_wmem_schedule, sk_forward_alloc can go
negetive which is a bug because sk_forward_alloc is a per-socket
space that has been forward charged so this can't be negative.
Fixes: f214f915e7 ("tcp: enable MSG_ZEROCOPY")
Signed-off-by: Talal Ahmad <talalahmad@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Wei Wang <weiwan@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c7bb4b8903 upstream.
While TCP stack scales reasonably well, there is still one part that
can be used to DDOS it.
IPv6 Packet too big messages have to lookup/insert a new route,
and if abused by attackers, can easily put hosts under high stress,
with many cpus contending on a spinlock while one is stuck in fib6_run_gc()
ip6_protocol_deliver_rcu()
icmpv6_rcv()
icmpv6_notify()
tcp_v6_err()
tcp_v6_mtu_reduced()
inet6_csk_update_pmtu()
ip6_rt_update_pmtu()
__ip6_rt_update_pmtu()
ip6_rt_cache_alloc()
ip6_dst_alloc()
dst_alloc()
ip6_dst_gc()
fib6_run_gc()
spin_lock_bh() ...
Some of our servers have been hit by malicious ICMPv6 packets
trying to _increase_ the MTU/MSS of TCP flows.
We believe these ICMPv6 packets are a result of a bug in one ISP stack,
since they were blindly sent back for _every_ (small) packet sent to them.
These packets are for one TCP flow:
09:24:36.266491 IP6 Addr1 > Victim ICMP6, packet too big, mtu 1460, length 1240
09:24:36.266509 IP6 Addr1 > Victim ICMP6, packet too big, mtu 1460, length 1240
09:24:36.316688 IP6 Addr1 > Victim ICMP6, packet too big, mtu 1460, length 1240
09:24:36.316704 IP6 Addr1 > Victim ICMP6, packet too big, mtu 1460, length 1240
09:24:36.608151 IP6 Addr1 > Victim ICMP6, packet too big, mtu 1460, length 1240
TCP stack can filter some silly requests :
1) MTU below IPV6_MIN_MTU can be filtered early in tcp_v6_err()
2) tcp_v6_mtu_reduced() can drop requests trying to increase current MSS.
This tests happen before the IPv6 routing stack is entered, thus
removing the potential contention and route exhaustion.
Note that IPv6 stack was performing these checks, but too late
(ie : after the route has been added, and after the potential
garbage collect war)
v2: fix typo caught by Martin, thanks !
v3: exports tcp_mtu_to_mss(), caught by David, thanks !
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit be5d1b61a2 upstream.
This commit fixes a bug (found by syzkaller) that could cause spurious
double-initializations for congestion control modules, which could cause
memory leaks or other problems for congestion control modules (like CDG)
that allocate memory in their init functions.
The buggy scenario constructed by syzkaller was something like:
(1) create a TCP socket
(2) initiate a TFO connect via sendto()
(3) while socket is in TCP_SYN_SENT, call setsockopt(TCP_CONGESTION),
which calls:
tcp_set_congestion_control() ->
tcp_reinit_congestion_control() ->
tcp_init_congestion_control()
(4) receive ACK, connection is established, call tcp_init_transfer(),
set icsk_ca_initialized=0 (without first calling cc->release()),
call tcp_init_congestion_control() again.
Note that in this sequence tcp_init_congestion_control() is called
twice without a cc->release() call in between. Thus, for CC modules
that allocate memory in their init() function, e.g, CDG, a memory leak
may occur. The syzkaller tool managed to find a reproducer that
triggered such a leak in CDG.
The bug was introduced when that commit 8919a9b31e ("tcp: Only init
congestion control if not initialized already")
introduced icsk_ca_initialized and set icsk_ca_initialized to 0 in
tcp_init_transfer(), missing the possibility for a sequence like the
one above, where a process could call setsockopt(TCP_CONGESTION) in
state TCP_SYN_SENT (i.e. after the connect() or TFO open sendmsg()),
which would call tcp_init_congestion_control(). It did not intend to
reset any initialization that the user had already explicitly made;
it just missed the possibility of that particular sequence (which
syzkaller managed to find).
Fixes: 8919a9b31e ("tcp: Only init congestion control if not initialized already")
Reported-by: syzbot+f1e24a0594d4e3a895d3@syzkaller.appspotmail.com
Signed-off-by: Nguyen Dinh Phi <phind.uet@gmail.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Tested-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 561022acb1 upstream.
While tp->mtu_info is read while socket is owned, the write
sides happen from err handlers (tcp_v[46]_mtu_reduced)
which only own the socket spinlock.
Fixes: 563d34d057 ("tcp: dont drop MTU reduction indications")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 71158bb1f2 upstream.
The MPTCP receive path is hooked only into the TCP slow-path.
The DSS presence allows plain MPTCP traffic to hit that
consistently.
Since commit e1ff9e82e2 ("net: mptcp: improve fallback to TCP"),
when an MPTCP socket falls back to TCP, it can hit the TCP receive
fast-path, and delay or stop triggering the event notification.
Address the issue explicitly disabling the header prediction
for MPTCP sockets.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/200
Fixes: e1ff9e82e2 ("net: mptcp: improve fallback to TCP")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2d6608b57c upstream.
The degree values were reversed out from the magic tap values of 7 (in)
and 15 + inversion (out) initially suggested by Aspeed.
With the patch tacoma survives several gigabytes of reads and writes
using dd while without it locks up randomly during the boot process.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20210625061017.1149942-1-andrew@aj.id.au
Fixes: 2fc88f9235 ("mmc: sdhci-of-aspeed: Expose clock phase controls")
Fixes: 961216c135 ("ARM: dts: aspeed: Add Rainier system")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca46ad2214 upstream.
Tacoma and Rainier both have a line-names array that is too long:
gpio gpiochip0: gpio-line-names is length 232 but should be at most length 208
This was probably copied from an AST2500 device tree that did have more
GPIOs on the controller.
Fixes: e9b24b55ca ("ARM: dts: aspeed: rainier: Add gpio line names")
Fixes: 2f68e4e7df ("ARM: dts: aspeed: tacoma: Add gpio line names")
Link: https://lore.kernel.org/r/20210624090742.56640-1-joel@jms.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d952cfaf0c upstream.
When a new CONFIG option is available, Kbuild shows a prompt to get
the user input.
$ make
[ snip ]
Core Scheduling for SMT (SCHED_CORE) [N/y/?] (NEW)
This is the only interactive place in the build process.
Commit 174a1dcc96 ("kbuild: sink stdout from cmd for silent build")
suppressed Kconfig prompts as well because syncconfig is invoked by
the 'cmd' macro. You cannot notice the fact that Kconfig is waiting
for the user input.
Use 'kecho' to show the equivalent short log without suppressing stdout
from sub-make.
Fixes: 174a1dcc96 ("kbuild: sink stdout from cmd for silent build")
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Tested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit deb7178eb9 upstream.
fp is netdev private data and it cannot be
used after free_netdev() call. Using fp after free_netdev()
can cause UAF bug. Fix it by moving free_netdev() after error message.
Fixes: 61414f5ec9 ("FDDI: defza: Add support for DEC FDDIcontroller 700
TURBOchannel adapter")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bcb9928a15 upstream.
This was not caught because there is no switch driver which implements
the .port_bridge_join but not .port_bridge_leave method, but it should
nonetheless be fixed, as in certain conditions (driver development) it
might lead to NULL pointer dereference.
Fixes: f66a6a69f9 ("net: dsa: permit cross-chip bridging between all trees in the system")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67a9c94317 upstream.
skb_tunnel_info() returns pointer of lwtstate->data as ip_tunnel_info
type without validation. lwtstate->data can have various types such as
mpls_iptunnel_encap, etc and these are not compatible.
So skb_tunnel_info() should validate before returning that pointer.
Splat looks like:
BUG: KASAN: slab-out-of-bounds in vxlan_get_route+0x418/0x4b0 [vxlan]
Read of size 2 at addr ffff888106ec2698 by task ping/811
CPU: 1 PID: 811 Comm: ping Not tainted 5.13.0+ #1195
Call Trace:
dump_stack_lvl+0x56/0x7b
print_address_description.constprop.8.cold.13+0x13/0x2ee
? vxlan_get_route+0x418/0x4b0 [vxlan]
? vxlan_get_route+0x418/0x4b0 [vxlan]
kasan_report.cold.14+0x83/0xdf
? vxlan_get_route+0x418/0x4b0 [vxlan]
vxlan_get_route+0x418/0x4b0 [vxlan]
[ ... ]
vxlan_xmit_one+0x148b/0x32b0 [vxlan]
[ ... ]
vxlan_xmit+0x25c5/0x4780 [vxlan]
[ ... ]
dev_hard_start_xmit+0x1ae/0x6e0
__dev_queue_xmit+0x1f39/0x31a0
[ ... ]
neigh_xmit+0x2f9/0x940
mpls_xmit+0x911/0x1600 [mpls_iptunnel]
lwtunnel_xmit+0x18f/0x450
ip_finish_output2+0x867/0x2040
[ ... ]
Fixes: 61adedf3e3 ("route: move lwtunnel state to dst_entry")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0336f8ffec upstream.
priv is netdev private data and it cannot be
used after free_netdev() call. Using priv after free_netdev()
can cause UAF bug. Fix it by moving free_netdev() at the end of the
function.
Fixes: 1e0a8b13d3 ("tlan: cancel work at remove path")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad297cd2db upstream.
adpt is netdev private data and it cannot be
used after free_netdev() call. Using adpt after free_netdev()
can cause UAF bug. Fix it by moving free_netdev() at the end of the
function.
Fixes: 54e19bc74f ("net: qcom/emac: do not use devm on internal phy pdev")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c78eaeebe8 upstream.
In case of netdev registration failure the code path will
jump to init_fail label:
init_fail:
netdev_err(ndev, "init failed\n");
moxart_mac_free_memory(ndev);
irq_map_fail:
free_netdev(ndev);
return ret;
So, there is no need to call free_netdev() before jumping
to error handling path, since it can cause UAF or double-free
bug.
Fixes: 6c821bd9ed ("net: Add MOXA ART SoCs ethernet driver")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9992a078b1 upstream.
Commit 28e104d002 ("net: ip_tunnel: fix mtu calculation") removed
dev->hard_header_len subtraction when calculate MTU for tunnel devices
as there is an overhead for device that has header_ops.
But there are ETHER tunnel devices, like gre_tap or erspan, which don't
have header_ops but set dev->hard_header_len during setup. This makes
pkts greater than (MTU - ETH_HLEN) could not be xmited. Fix it by
subtracting the ETHER tunnel devices' dev->hard_header_len for MTU
calculation.
Fixes: 28e104d002 ("net: ip_tunnel: fix mtu calculation")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b452550a2 upstream.
Make sure that we disable each of the TX and RX queues in the TDMA and
RDMA control registers. This is a correctness change to be symmetrical
with the code that enables the TX and RX queues.
Tested-by: Maxime Ripard <maxime@cerno.tech>
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09adf7566d upstream.
There are two pointers in struct xfrm_state_offload, *dev, *real_dev.
These are used in callback functions of struct xfrmdev_ops.
The *dev points whether bonding interface or real interface.
If bonding ipsec offload is used, it points bonding interface If not,
it points real interface.
And real_dev always points real interface.
So, netdevsim should always use real_dev instead of dev.
Of course, real_dev always not be null.
Test commands:
ip netns add A
ip netns exec A bash
modprobe netdevsim
echo "1 1" > /sys/bus/netdevsim/new_device
ip link add bond0 type bond mode active-backup
ip link set eth0 master bond0
ip link set eth0 up
ip link set bond0 up
ip x s add proto esp dst 14.1.1.1 src 15.1.1.1 spi 0x07 mode \
transport reqid 0x07 replay-window 32 aead 'rfc4106(gcm(aes))' \
0x44434241343332312423222114131211f4f3f2f1 128 sel src 14.0.0.52/24 \
dst 14.0.0.70/24 proto tcp offload dev bond0 dir in
Splat looks like:
BUG: spinlock bad magic on CPU#5, kworker/5:1/53
lock: 0xffff8881068c2cc8, .magic: 11121314, .owner: <none>/-1,
.owner_cpu: -235736076
CPU: 5 PID: 53 Comm: kworker/5:1 Not tainted 5.13.0-rc3+ #1168
Workqueue: events linkwatch_event
Call Trace:
dump_stack+0xa4/0xe5
do_raw_spin_lock+0x20b/0x270
? rwlock_bug.part.1+0x90/0x90
_raw_spin_lock_nested+0x5f/0x70
bond_get_stats+0xe4/0x4c0 [bonding]
? rcu_read_lock_sched_held+0xc0/0xc0
? bond_neigh_init+0x2c0/0x2c0 [bonding]
? dev_get_alias+0xe2/0x190
? dev_get_port_parent_id+0x14a/0x360
? rtnl_unregister+0x190/0x190
? dev_get_phys_port_name+0xa0/0xa0
? memset+0x1f/0x40
? memcpy+0x38/0x60
? rtnl_phys_switch_id_fill+0x91/0x100
dev_get_stats+0x8c/0x270
rtnl_fill_stats+0x44/0xbe0
? nla_put+0xbe/0x140
rtnl_fill_ifinfo+0x1054/0x3ad0
[ ... ]
Fixes: 272c2330ad ("xfrm: bail early on slave pass over skb")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a019abd802 upstream.
Since commit 2796d0c648 ("bridge: Automatically manage
port promiscuous mode.")
bridges with `vlan_filtering 1` and only 1 auto-port don't
set IFF_PROMISC for unicast-filtering-capable ports.
Normally on port changes `br_manage_promisc` is called to
update the promisc flags and unicast filters if necessary,
but it cannot distinguish between *new* ports and ones
losing their promisc flag, and new ports end up not
receiving the MAC address list.
Fix this by calling `br_fdb_sync_static` in `br_add_if`
after the port promisc flags are updated and the unicast
filter was supposed to have been filled.
Fixes: 2796d0c648 ("bridge: Automatically manage port promiscuous mode.")
Signed-off-by: Wolfgang Bumiller <w.bumiller@proxmox.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77ac5e40c4 upstream.
When cleaning up the nf_table in tcf_ct_flow_table_cleanup_work
there is no guarantee that the callback list, added to by
nf_flow_table_offload_add_cb, is empty. This means that it is
possible that the flow_block_cb memory allocated will be lost.
Fix this by iterating the list and freeing the flow_block_cb entries
before freeing the nf_table entry (via freeing ct_ft).
Fixes: 978703f425 ("netfilter: flowtable: Add API for registering to flow table events")
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b22580233d upstream.
Commit dacce2be33 ("vmxnet3: add geneve and vxlan tunnel offload
support") added support for encapsulation offload. However, the inner
offload capability is to be restricted to UDP tunnels with default
Vxlan and Geneve ports.
This patch fixes the issue for tunnels with non-default ports using
features check capability and filtering appropriate features for such
tunnels.
Fixes: dacce2be33 ("vmxnet3: add geneve and vxlan tunnel offload support")
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8955b90c3c upstream.
The confirm operation should be checked. If there are any failed,
the packet should be dropped like in ovs and netfilter.
Fixes: b57dc7c13e ("net/sched: Introduce action ct")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40fc3054b4 upstream.
Commit 628a5c5618 ("[INET]: Add IP(V6)_PMTUDISC_RPOBE") introduced
ip6_skb_dst_mtu with return value of signed int which is inconsistent
with actually returned values. Also 2 users of this function actually
assign its value to unsigned int variable and only __xfrm6_output
assigns result of this function to signed variable but actually uses
as unsigned in further comparisons and calls. Change this function
to return unsigned int value.
Fixes: 628a5c5618 ("[INET]: Add IP(V6)_PMTUDISC_RPOBE")
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c07fff3492 upstream.
Commit 23e8b470c7 ("net: dsa: mv88e6xxx: Add devlink param for ATU
hash algorithm.") introduced ATU hash algorithm access via devlink, but
did not enable it for Topaz.
Enable this feature also for Topaz.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: 23e8b470c7 ("net: dsa: mv88e6xxx: Add devlink param for ATU hash algorithm.")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3709488790 upstream.
Commit 9e5baf9b36 ("net: dsa: mv88e6xxx: add RMU disable op")
introduced .rmu_disable() method with implementation for several models,
but forgot to add Topaz, which can use the Peridot implementation.
Use the Peridot implementation of .rmu_disable() on Topaz.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: 9e5baf9b36 ("net: dsa: mv88e6xxx: add RMU disable op")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7da467d82d upstream.
Commit f3a2cd326e ("net: dsa: mv88e6xxx: introduce .port_set_policy")
introduced .port_set_policy() method with implementation for several
models, but forgot to add Topaz, which can use the 6352 implementation.
Use the 6352 implementation of .port_set_policy() on Topaz.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: f3a2cd326e ("net: dsa: mv88e6xxx: introduce .port_set_policy")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a3c680aa2 upstream.
Setting the EXT_ENERGY_DET_MASK bit allows the port energy detection
logic of the internal PHY to prevent the system from sleeping. Some
internal PHYs will report that energy is detected when the network
interface is closed which can prevent the system from going to sleep
if WoL is enabled when the interface is brought down.
Since the driver does not support waking the system on this logic,
this commit clears the bit whenever the internal PHY is powered up
and the other logic for manipulating the bit is removed since it
serves no useful function.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 122e093c17 upstream.
On systems with memory nodes sorted in descending order, for instance Dell
Precision WorkStation T5500, the struct pages for higher PFNs and
respectively lower nodes, could be overwritten by the initialization of
struct pages corresponding to the holes in the memory sections.
For example for the below memory layout
[ 0.245624] Early memory node ranges
[ 0.248496] node 1: [mem 0x0000000000001000-0x0000000000090fff]
[ 0.251376] node 1: [mem 0x0000000000100000-0x00000000dbdf8fff]
[ 0.254256] node 1: [mem 0x0000000100000000-0x0000001423ffffff]
[ 0.257144] node 0: [mem 0x0000001424000000-0x0000002023ffffff]
the range 0x1424000000 - 0x1428000000 in the beginning of node 0 starts in
the middle of a section and will be considered as a hole during the
initialization of the last section in node 1.
The wrong initialization of the memory map causes panic on boot when
CONFIG_DEBUG_VM is enabled.
Reorder loop order of the memory map initialization so that the outer loop
will always iterate over populated memory regions in the ascending order
and the inner loop will select the zone corresponding to the PFN range.
This way initialization of the struct pages for the memory holes will be
always done for the ranges that are actually not populated.
[akpm@linux-foundation.org: coding style fixes]
Link: https://lkml.kernel.org/r/YNXlMqBbL+tBG7yq@kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=213073
Link: https://lkml.kernel.org/r/20210624062305.10940-1-rppt@kernel.org
Fixes: 0740a50b9b ("mm/page_alloc.c: refactor initialization of struct page for holes in memory layout")
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Boris Petkov <bp@alien8.de>
Cc: Robert Shteynfeld <robert.shteynfeld@gmail.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: David Hildenbrand <david@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[rppt: tweak for compatibility with IA64's override of memmap_init]
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f34f1eac3 upstream.
We tried to do something similar in b569a17607 ("userfaultfd: wp: drop
_PAGE_UFFD_WP properly when fork") previously, but it's not doing it all
right.. A few fixes around the code path:
1. We were referencing VM_UFFD_WP vm_flags on the _old_ vma rather
than the new vma. That's overlooked in b569a17607, so it won't work
as expected. Thanks to the recent rework on fork code
(7a4830c380), we can easily get the new vma now, so switch the
checks to that.
2. Dropping the uffd-wp bit in copy_huge_pmd() could be wrong if the
huge pmd is a migration huge pmd. When it happens, instead of using
pmd_uffd_wp(), we should use pmd_swp_uffd_wp(). The fix is simply to
handle them separately.
3. Forget to carry over uffd-wp bit for a write migration huge pmd
entry. This also happens in copy_huge_pmd(), where we converted a
write huge migration entry into a read one.
4. In copy_nonpresent_pte(), drop uffd-wp if necessary for swap ptes.
5. In copy_present_page() when COW is enforced when fork(), we also
need to pass over the uffd-wp bit if VM_UFFD_WP is armed on the new
vma, and when the pte to be copied has uffd-wp bit set.
Remove the comment in copy_present_pte() about this. It won't help a huge
lot to only comment there, but comment everywhere would be an overkill.
Let's assume the commit messages would help.
[peterx@redhat.com: fix a few thp pmd missing uffd-wp bit]
Link: https://lkml.kernel.org/r/20210428225030.9708-4-peterx@redhat.com
Link: https://lkml.kernel.org/r/20210428225030.9708-3-peterx@redhat.com
Fixes: b569a17607 ("userfaultfd: wp: drop _PAGE_UFFD_WP properly when fork")
Signed-off-by: Peter Xu <peterx@redhat.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Axel Rasmussen <axelrasmussen@google.com>
Cc: Brian Geffon <bgeffon@google.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Joe Perches <joe@perches.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Wang Qing <wangqing@vivo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5fc7a5f6fd upstream.
Patch series "mm/uffd: Misc fix for uffd-wp and one more test".
This series tries to fix some corner case bugs for uffd-wp on either thp
or fork(). Then it introduced a new test with pagemap/pageout.
Patch layout:
Patch 1: cleanup for THP, it'll slightly simplify the follow up patches
Patch 2-4: misc fixes for uffd-wp here and there; please refer to each patch
Patch 5: add pagemap support for uffd-wp
Patch 6: add pagemap/pageout test for uffd-wp
The last test introduced can also verify some of the fixes in previous
patches, as the test will fail without the fixes. However it's not easy
to verify all the changes in patch 2-4, but hopefully they can still be
properly reviewed.
Note that if considering the ongoing uffd-wp shmem & hugetlbfs work, patch
5 will be incomplete as it's missing e.g. hugetlbfs part or the special
swap pte detection. However that's not needed in this series, and since
that series is still during review, this series does not depend on that
one (the last test only runs with anonymous memory, not file-backed). So
this series can be merged even before that series.
This patch (of 6):
Huge zero page is handled in a special path in copy_huge_pmd(), however it
should share most codes with a normal thp page. Trying to share more code
with it by removing the special path. The only leftover so far is the
huge zero page refcounting (mm_get_huge_zero_page()), because that's
separately done with a global counter.
This prepares for a future patch to modify the huge pmd to be installed,
so that we don't need to duplicate it explicitly into huge zero page case
too.
Link: https://lkml.kernel.org/r/20210428225030.9708-1-peterx@redhat.com
Link: https://lkml.kernel.org/r/20210428225030.9708-2-peterx@redhat.com
Signed-off-by: Peter Xu <peterx@redhat.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Mike Kravetz <mike.kravetz@oracle.com>, peterx@redhat.com
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Axel Rasmussen <axelrasmussen@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Brian Geffon <bgeffon@google.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Joe Perches <joe@perches.com>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Wang Qing <wangqing@vivo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3a52a48973 ]
Move the turris-mox-rwtm firmware node from Turris MOX' device tree into
the generic armada-37xx.dtsi file and use the generic compatible string
'marvell,armada-3700-rwtm-firmware' instead of the current one.
Turris MOX DTS file contains also old compatible string for backward
compatibility.
The Turris MOX rWTM firmware can be used on any Armada 37xx device,
giving them access to the rWTM hardware random number generator, which
is otherwise unavailable.
This change allows Linux to load the turris-mox-rwtm.ko module on these
boards.
Tested on ESPRESSObin v5 with both default Marvell WTMI firmware and
CZ.NIC's firmware. With default WTMI firmware the turris-mox-rwtm fails
to probe, while with CZ.NIC's firmware it registers the HW random number
generator.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90ae47215d ]
Add more generic compatible string 'marvell,armada-3700-rwtm-firmware' for
this driver, since it can also be used on other Armada 3720 devices.
Current compatible string 'cznic,turris-mox-rwtm' is kept for backward
compatibility.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03313d1c3a ]
The optional @ref parameter might contain an NULL node_name, so
prevent dereferencing it in cifs_compose_mount_options().
Addresses-Coverity: 1476408 ("Explicit null dereferenced")
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41d71fe59c ]
The existing CALL_ON_STACK() macro allows for subtle bugs:
- There is no type checking of the function that is being called. That
is: missing or too many arguments do not cause any compile error or
warning. The same is true if the return type of the called function
changes. This can lead to quite random bugs.
- Sign and zero extension of arguments is missing. Given that the s390
C ABI requires that the caller of a function performs proper sign
and zero extension this can also lead to subtle bugs.
- If arguments to the CALL_ON_STACK() macros contain functions calls
register corruption can happen due to register asm constructs being
used.
Therefore introduce a new call_on_stack() macro which is supposed to
fix all these problems.
Reviewed-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8e9cc20b8 ]
tinyconfig fails to boot, because without CONFIG_BUG report_bug()
always returns BUG_TRAP_TYPE_BUG, which causes mc 0,0 in
test_monitor_call() to panic. Fix by skipping the test without
CONFIG_BUG.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e5c9f9a75 ]
Zone device is enabled after thermal_zone_of_sensor_register() completion,
but it's not disabled before senor is unregistered, leaving temperature
polling active. This results in accessing a disabled zone device and
produces a warning about this problem. Stop zone device before
unregistering it in order to fix this "use-after-free" problem.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210616190417.32214-3-digetx@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72d0ad7cb5 ]
The time remaining until expiry of the refresh_timer can be negative.
Casting the type to an unsigned 64-bit value will cause integer
underflow, making the runtime_refresh_within return false instead of
true. These situations are rare, but they do happen.
This does not cause user-facing issues or errors; other than
possibly unthrottling cfs_rq's using runtime from the previous period(s),
making the CFS bandwidth enforcement less strict in those (special)
situations.
Signed-off-by: Odin Ugedal <odin@uged.al>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Ben Segall <bsegall@google.com>
Link: https://lore.kernel.org/r/20210629121452.18429-1-odin@uged.al
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49da96d779 ]
Offlining a SATA device connected to a hisi SAS controller and then
scanning the host will result in detecting 255 non-existent devices:
# lsscsi
[2:0:0:0] disk ATA Samsung SSD 860 2B6Q /dev/sda
[2:0:1:0] disk ATA WDC WD2003FYYS-3 1D01 /dev/sdb
[2:0:2:0] disk SEAGATE ST600MM0006 B001 /dev/sdc
# echo "offline" > /sys/block/sdb/device/state
# echo "- - -" > /sys/class/scsi_host/host2/scan
# lsscsi
[2:0:0:0] disk ATA Samsung SSD 860 2B6Q /dev/sda
[2:0:1:0] disk ATA WDC WD2003FYYS-3 1D01 /dev/sdb
[2:0:1:1] disk ATA WDC WD2003FYYS-3 1D01 /dev/sdh
...
[2:0:1:255] disk ATA WDC WD2003FYYS-3 1D01 /dev/sdjb
After a REPORT LUN command issued to the offline device fails, the SCSI
midlayer tries to do a sequential scan of all devices whose LUN number is
not 0. However, SATA does not support LUN numbers at all.
Introduce a generic sas_slave_alloc() handler which will return -ENXIO for
SATA devices if the requested LUN number is larger than 0 and make libsas
drivers use this function as their .slave_alloc callback.
Link: https://lore.kernel.org/r/20210622034037.1467088-1-yuyufen@huawei.com
Reported-by: Wu Bo <wubo40@huawei.com>
Suggested-by: John Garry <john.garry@huawei.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 332a9dd1d8 ]
The shifting of the u8 integer returned fom ahc_inb(ahc, port+3) by 24 bits
to the left will be promoted to a 32 bit signed int and then sign-extended
to a u64. In the event that the top bit of the u8 is set then all then all
the upper 32 bits of the u64 end up as also being set because of the
sign-extension. Fix this by casting the u8 values to a u64 before the 24
bit left shift.
[ This dates back to 2002, I found the offending commit from the git
history git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git,
commit f58eb66c0b0a ("Update aic7xxx driver to 6.2.10...") ]
Link: https://lore.kernel.org/r/20210621151727.20667-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Addresses-Coverity: ("Unintended sign extension")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 742b0d7e15 ]
Interrupt line can be configured on different hardware in different way,
even inverted. Therefore driver should not enforce specific trigger
type - edge falling - but instead rely on Devicetree to configure it.
The Maxim 77686 datasheet describes the interrupt line as active low
with a requirement of acknowledge from the CPU therefore the edge
falling is not correct.
The interrupt line is shared between PMIC and RTC driver, so using level
sensitive interrupt is here especially important to avoid races. With
an edge configuration in case if first PMIC signals interrupt followed
shortly after by the RTC, the interrupt might not be yet cleared/acked
thus the second one would not be noticed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210526172036.183223-6-krzysztof.kozlowski@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a979522a1a ]
To avoid unnecessary recompilations, mkcompile_h does not regenerate
compile.h if just the timestamp changed.
Though, if KBUILD_BUILD_TIMESTAMP is set, an explicit timestamp for the
build was requested, in which case we should not ignore it.
If a user follows the documentation for reproducible builds [1] and
defines KBUILD_BUILD_TIMESTAMP as the git commit timestamp, a clean
build will have the correct timestamp. A subsequent cherry-pick (or
amend) changes the commit timestamp and if an incremental build is done
with a different KBUILD_BUILD_TIMESTAMP now, that new value is not taken
into consideration. But it should for reproducibility.
Hence, whenever KBUILD_BUILD_TIMESTAMP is explicitly set, do not ignore
UTS_VERSION when making a decision about whether the regenerated version
of compile.h should be moved into place.
[1] https://www.kernel.org/doc/html/latest/kbuild/reproducible-builds.html
Signed-off-by: Matthias Maennich <maennich@google.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ae5950db6 ]
With -Wshadow:
drivers/thermal/rcar_gen3_thermal.c: In function ‘rcar_gen3_thermal_probe’:
drivers/thermal/rcar_gen3_thermal.c:310:13: warning: declaration of ‘rcar_gen3_ths_tj_1’ shadows a global declaration [-Wshadow]
310 | const int *rcar_gen3_ths_tj_1 = of_device_get_match_data(dev);
| ^~~~~~~~~~~~~~~~~~
drivers/thermal/rcar_gen3_thermal.c:246:18: note: shadowed declaration is here
246 | static const int rcar_gen3_ths_tj_1 = 126;
| ^~~~~~~~~~~~~~~~~~
To add to the confusion, the local variable has a different type.
Fix the shadowing by renaming the local variable to ths_tj_1.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/9ea7e65d0331daba96f9a7925cb3d12d2170efb1.1623076804.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15a5261e4d ]
This fixes multiple issues with the current non-existent PCIe clock setup:
The controller can run at up to 250MHz, so use a parent that provides this
clock.
The PHY needs an exact 100MHz reference clock to function if the PCIe
refclock is not fed in via the refclock pads. While this mode is not
supported (yet) in the driver it doesn't hurt to make sure we are
providing a clock with the right rate.
The AUX clock is specified to have a maximum clock rate of 10MHz. So
the current setup, which drives it straight from the 25MHz oscillator is
actually overclocking the AUX input.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8240c972c1 ]
On LS2088A-RDB board, if the spi-fsl-dspi driver is built as module
then its probe fails with the following warning:
[ 10.471363] couldn't get idr
[ 10.471381] WARNING: CPU: 4 PID: 488 at drivers/spi/spi.c:2689 spi_register_controller+0x73c/0x8d0
...
[ 10.471651] fsl-dspi 2100000.spi: Problem registering DSPI ctlr
[ 10.471708] fsl-dspi: probe of 2100000.spi failed with error -16
Reason for the failure is that bus-num property is set for dspi node.
However, bus-num property is not set for the qspi node. If probe for
spi-fsl-qspi happens first then id 0 is dynamically allocated to it.
Call to spi_register_controller() from spi-fsl-dspi driver then fails.
Since commit 29d2daf2c3 ("spi: spi-fsl-dspi: Make bus-num property
optional") bus-num property is optional. Remove bus-num property from
dspi node to fix the issue.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd778b8939 ]
The tegra186_bpmp_ops symbol is used on Tegra234, so make sure it's
available.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e2d0ee225e ]
The tegra30_fuse_read() symbol is used on Tegra234, so make sure it's
available.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 093a474ce1 ]
If the PM related modules are not loaded and PM firmware not configured,
the system suspend fails to resume. Let's fix this by adding initial
platform_suspend_ops to block suspend and warn about missing modules.
When pm33xx and wkup_m3_ipc have been loaded and m3 coprocessor booted
with it's firmware, pm33xx sets up working platform_suspend_ops. Note
that we need to configure at least PM_SUSPEND_STANDBY to have
suspend_set_ops().
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4bf4abe190 ]
On some STM32 MP15 boards, stpmic node is not correct which generates
warnings running "make dtbs_check W=1" command. Issues are:
-"regulator-active-discharge" is not a boolean but an uint32.
-"regulator-over-current-protection" is not a valid entry for vref_ddr.
-LDO4 has a fixed voltage (3v3) so min/max entries are not allowed.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f493162319 ]
The Seeed SoM-STM32MP157C device tree had the eMMC’s (SDMMC2) VQMMC
supply set to v3v3 (buck4), the same as the VMMC supply. That was
incorrect, as on the SoM, the VQMMC supply is provided from vdd (buck3)
instead.
Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0740fb869 ]
Fix compilation warning on 64bit platforms caused by implicit promotion
of 32bit signed integer to a 64bit unsigned value which happens after
enabling compile-testing of the EMC drivers.
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf24b91f4b ]
Fix following warning observed with "make dtbs_check W=1" command.
It concerns f429 eval and disco boards, f769 disco board.
Warning (unit_address_vs_reg): /gpio_keys/button@0: node has a unit name,
but no reg or ranges property
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0171b07373 ]
The microSD card detect pin is physically connected to the MPU pin PI3.
The Device Tree configuration of the card detect pin was wrong—it was
set to pin PB7 instead. If such configuration was used, the kernel would
hang on “Waiting for root device” when booting from a microSD card.
Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4dd6066bc ]
The 3v3 regulator GPIO is GP6 and not GP7, which is the DDR regulator.
Both regulators are always-on, nevertheless the DT model needs to be
corrected, fix it.
Reported-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f45da704d ]
All Tegra boards which use WM8903 audio codec are specifying a wrong
polarity for the headphones detection GPIO. The kernel driver hardcodes
the polarity to active-low, which is the correct polarity, so we can fix
the device-trees safely.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69db725cdb ]
The MCU RGMII MCU_RGMII1_TXC pin is defined as input by mistake, although
this does not make any difference functionality wise it's better to update
to avoid confusion.
Hence fix MCU RGMII MCU_RGMII1_TXC pin pinmux definitions to be an output
in K3 am654x/j721e/j7200 board files.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210526132041.6104-1-grygorii.strashko@ti.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e7f5ee113 ]
A number of sub-mailbox node names in various OMAP2+ dts files are
currently using underscores. This is not adhering to the node name
convention, fix all of these to use hiphens.
These nodes are already using the prefix mbox, so they will be in
compliance with the sub-mailbox node name convention being added in
the OMAP Mailbox YAML binding as well.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7d30b8fcd ]
The ti,no-reset-on-init flag need to be at the interconnect target module
level for the modules that have it defined.
The ti-sysc driver handles this case, but produces warning, not a critical
issue.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2566d5b8c1 ]
The ti,no-reset-on-init flag need to be at the interconnect target module
level for the modules that have it defined.
The ti-sysc driver handles this case, but produces warning, not a critical
issue.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b644c5e01c ]
The ti,no-reset-on-init flag need to be at the interconnect target module
level for the modules that have it defined.
The ti-sysc driver handles this case, but produces warning, not a critical
issue.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 174a1dcc96 ]
When building with 'make -s', no output to stdout should be printed.
As Arnd Bergmann reported [1], mkimage shows the detailed information
of the generated images.
I think this should be suppressed by the 'cmd' macro instead of by
individual scripts.
Insert 'exec >/dev/null;' in order to redirect stdout to /dev/null for
silent builds.
[Note about this implementation]
'exec >/dev/null;' may look somewhat tricky, but this has a reason.
Appending '>/dev/null' at the end of command line is a common way for
redirection, so I first tried this:
cmd = @set -e; $(echo-cmd) $(cmd_$(1)) >/dev/null
... but it would not work if $(cmd_$(1)) itself contains a redirection.
For example, cmd_wrap in scripts/Makefile.asm-generic redirects the
output from the 'echo' command into the target file.
It would be expanded into:
echo "#include <asm-generic/$*.h>" > $@ >/dev/null
Then, the target file gets empty because the string will go to /dev/null
instead of $@.
Next, I tried this:
cmd = @set -e; $(echo-cmd) { $(cmd_$(1)); } >/dev/null
The form above would be expanded into:
{ echo "#include <asm-generic/$*.h>" > $@; } >/dev/null
This works as expected. However, it would be a syntax error if
$(cmd_$(1)) is empty.
When CONFIG_TRIM_UNUSED_KSYMS is disabled, $(call cmd,gen_ksymdeps) in
scripts/Makefile.build would be expanded into:
set -e; { ; } >/dev/null
..., which causes an syntax error.
I also tried this:
cmd = @set -e; $(echo-cmd) ( $(cmd_$(1)) ) >/dev/null
... but this causes a syntax error for the same reason.
So, finally I adopted:
cmd = @set -e; $(echo-cmd) exec >/dev/null; $(cmd_$(1))
[1]: https://lore.kernel.org/lkml/20210514135752.2910387-1-arnd@kernel.org/
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 723de6a412 ]
Without SoC specific PHY fixups the network interface on this board will
fail to work. Provide missing DT properties to make it work again.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4beba40119 ]
This adds a mounting matrix to the accelerometer
on the TVK1281618 R3.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4917b70281 ]
Rename the AB8500 gpio controller node from ab8500-gpio to
ab8500-gpiocontroller, since -gpio is a common suffix for
gpio consumers.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b82f8e2992 ]
A test with the command below gives this error:
/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dt.yaml:
sdmmcio-regulator: states:0:
[1800000, 1, 3300000, 0] is too long
dtbs_check expects regulator-gpio states in a format
of 2 per item, so fix them all.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/
regulator/gpio-regulator.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210510215840.16270-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14cdc1f243 ]
Serial interface uart3 on phyFLEX board is capable of 5-wire connection
including signals RTS and CTS for hardware flow control.
Fix signals UART3_CTS_B and UART3_RTS_B padmux assignments and add
missing property "uart-has-rtscts" to allow serial interface to be
configured and used with the hardware flow control.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05cf8fffcd ]
The to_ti_syscon_reset_data macro currently only works if the
parameter passed into it is called 'rcdev'.
Fixes a checkpatch --strict issue:
CHECK: Macro argument reuse 'rcdev' - possible side-effects?
#53: FILE: drivers/reset/reset-ti-syscon.c:53:
+#define to_ti_syscon_reset_data(rcdev) \
+ container_of(rcdev, struct ti_syscon_reset_data, rcdev)
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7ecfad495 ]
A test with the command below aimed at powerpc generates
notifications in the Rockchip arm64 tree.
Fix pinctrl "sleep" nodename by renaming it to "suspend"
for rk3399.dtsi
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/powerpc/sleep.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210126110221.10815-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dfbfb86a43 ]
A test with the command below aimed at powerpc generates
notifications in the Rockchip ARM tree.
Fix pinctrl "sleep" nodename by renaming it to "suspend"
for rk3036-kylin and rk3288
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/powerpc/sleep.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210126110221.10815-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
