mmc: Apply ERASE_BROKEN quirks correctly

Signed-off-by: Phil Elwell <phil@raspberrypi.org>

Documentation/devicetree/bindings/ata/ahci-platform.txt

@@ -30,6 +30,10 @@ Optional properties:
 - target-supply     : regulator for SATA target power
 - phys              : reference to the SATA PHY node
 - phy-names         : must be "sata-phy"
+- ports-implemented : Mask that indicates which ports that the HBA supports
+		      are available for software to use. Useful if PORTS_IMPL
+		      is not programmed by the BIOS, which is true with
+		      some embedded SOC's.
 
 Required properties when using sub-nodes:
 - #address-cells    : number of cells to encode an address

Documentation/devicetree/bindings/clock/brcm,bcm2835-aux-clock.txt

@@ -0,0 +1,31 @@
+Broadcom BCM2835 auxiliary peripheral support
+
+This binding uses the common clock binding:
+    Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+The auxiliary peripherals (UART, SPI1, and SPI2) have a small register
+area controlling clock gating to the peripherals, and providing an IRQ
+status register.
+
+Required properties:
+- compatible:	Should be "brcm,bcm2835-aux"
+- #clock-cells:	Should be <1>. The permitted clock-specifier values can be
+		  found in include/dt-bindings/clock/bcm2835-aux.h
+- reg:		Specifies base physical address and size of the registers
+- clocks:	The parent clock phandle
+
+Example:
+
+	clocks: cprman@7e101000 {
+		compatible = "brcm,bcm2835-cprman";
+		#clock-cells = <1>;
+		reg = <0x7e101000 0x2000>;
+		clocks = <&clk_osc>;
+	};
+
+	aux: aux@0x7e215004 {
+		compatible = "brcm,bcm2835-aux";
+		#clock-cells = <1>;
+		reg = <0x7e215000 0x8>;
+		clocks = <&clocks BCM2835_CLOCK_VPU>;
+	};

Documentation/devicetree/bindings/clock/imx35-clock.txt

@@ -94,6 +94,7 @@ clocks and IDs.
 	csi_sel			79
 	iim_gate		80
 	gpu2d_gate		81
+	ckli_gate		82
 
 Examples:
 

Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt

@@ -35,6 +35,22 @@ Optional properties for HDMI:
 		  as an interrupt/status bit in the HDMI controller
 		  itself).  See bindings/pinctrl/brcm,bcm2835-gpio.txt
 
+Required properties for DPI:
+- compatible:	Should be "brcm,bcm2835-dpi"
+- reg:		Physical base address and length of the registers
+- clocks:	a) core: The core clock the unit runs on
+		b) pixel: The pixel clock that feeds the pixelvalve
+- port:		Port node with a single endpoint connecting to the panel
+		  device, as defined in [1]
+
+Required properties for V3D:
+- compatible:	Should be "brcm,bcm2835-v3d"
+- reg:		Physical base address and length of the V3D's registers
+- interrupts:	The interrupt number
+		  See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt
+
+[1] Documentation/devicetree/bindings/media/video-interfaces.txt
+
 Example:
 pixelvalve@7e807000 {
 	compatible = "brcm,bcm2835-pixelvalve2";
@@ -60,6 +76,38 @@ hdmi: hdmi@7e902000 {
 	clock-names = "pixel", "hdmi";
 };
 
+dpi: dpi@7e208000 {
+	compatible = "brcm,bcm2835-dpi";
+	reg = <0x7e208000 0x8c>;
+	clocks = <&clocks BCM2835_CLOCK_VPU>,
+	         <&clocks BCM2835_CLOCK_DPI>;
+	clock-names = "core", "pixel";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	port {
+		dpi_out: endpoint@0 {
+			remote-endpoint = <&panel_in>;
+		};
+	};
+};
+
+v3d: v3d@7ec00000 {
+	compatible = "brcm,bcm2835-v3d";
+	reg = <0x7ec00000 0x1000>;
+	interrupts = <1 10>;
+};
+
 vc4: gpu {
 	compatible = "brcm,bcm2835-vc4";
 };
+
+panel: panel {
+	compatible = "ontat,yx700wv03", "simple-panel";
+
+	port {
+		panel_in: endpoint {
+			remote-endpoint = <&dpi_out>;
+		};
+	};
+};

Documentation/devicetree/bindings/display/panel/ontat,yx700wv03.txt

@@ -0,0 +1,7 @@
+On Tat Industrial Company 7" DPI TFT panel.
+
+Required properties:
+- compatible: should be "ontat,yx700wv03"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.

Documentation/devicetree/bindings/dma/brcm,bcm2835-dma.txt

@@ -48,8 +48,8 @@ Example:
 
 bcm2835_i2s: i2s@7e203000 {
 	compatible = "brcm,bcm2835-i2s";
-	reg = <	0x7e203000 0x20>,
-	      < 0x7e101098 0x02>;
+	reg = <	0x7e203000 0x24>,
+	      < 0x7e101098 0x08>;
 
 	dmas = <&dma 2>,
 	       <&dma 3>;

Documentation/devicetree/bindings/misc/brcm,bcm2835-smi-dev.txt

@@ -0,0 +1,17 @@
+* Broadcom BCM2835 SMI character device driver.
+
+SMI or secondary memory interface is a peripheral specific to certain Broadcom
+SOCs, and is helpful for talking to things like parallel-interface displays
+and NAND flashes (in fact, most things with a parallel register interface).
+
+This driver adds a character device which provides a user-space interface to
+an instance of the SMI driver.
+
+Required properties:
+- compatible: "brcm,bcm2835-smi-dev"
+- smi_handle: a phandle to the smi node.
+
+Optional properties:
+- None.
+
+

Documentation/devicetree/bindings/misc/brcm,bcm2835-smi.txt

@@ -0,0 +1,48 @@
+* Broadcom BCM2835 SMI driver.
+
+SMI or secondary memory interface is a peripheral specific to certain Broadcom
+SOCs, and is helpful for talking to things like parallel-interface displays
+and NAND flashes (in fact, most things with a parallel register interface).
+
+Required properties:
+- compatible: "brcm,bcm2835-smi"
+- reg: Should contain location and length of SMI registers and SMI clkman regs
+- interrupts: *the* SMI interrupt.
+- pinctrl-names: should be "default".
+- pinctrl-0: the phandle of the gpio pin node.
+- brcm,smi-clock-source: the clock source for clkman
+- brcm,smi-clock-divisor: the integer clock divisor for clkman
+- dmas: the dma controller phandle and the DREQ number (4 on a 2835)
+- dma-names: the name used by the driver to request its channel.
+  Should be "rx-tx".
+
+Optional properties:
+- None.
+
+Examples:
+
+8 data pin configuration:
+
+smi: smi@7e600000 {
+	compatible = "brcm,bcm2835-smi";
+	reg = <0x7e600000 0x44>, <0x7e1010b0 0x8>;
+	interrupts = <2 16>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&smi_pins>;
+	brcm,smi-clock-source = <6>;
+	brcm,smi-clock-divisor = <4>;
+	dmas = <&dma 4>;
+	dma-names = "rx-tx";
+
+	status = "okay";
+};
+
+smi_pins: smi_pins {
+	brcm,pins = <2 3 4 5 6 7 8 9 10 11 12 13 14 15>;
+	/* Alt 1: SMI */
+	brcm,function = <5 5 5 5 5 5 5 5 5 5 5 5 5 5>;
+	/* /CS, /WE and /OE are pulled high, as they are
+	   generally active low signals */
+	brcm,pull = <2 2 2 2 2 2 0 0 0 0 0 0 0 0>;
+};
+

Documentation/devicetree/bindings/mtd/brcm,bcm2835-smi-nand.txt

@@ -0,0 +1,42 @@
+* BCM2835 SMI NAND flash
+
+This driver is a shim between the BCM2835 SMI driver (SMI is a peripheral for
+talking to parallel register interfaces) and Linux's MTD layer.
+
+Required properties:
+- compatible: "brcm,bcm2835-smi-nand"
+- status: "okay"
+
+Optional properties:
+- partition@n, where n is an integer from a consecutive sequence starting at 0
+	- Difficult to store partition table on NAND device - normally put it
+	in the source code, kernel bootparams, or device tree (the best way!)
+	- Sub-properties:
+		- label: the partition name, as shown by mtdinfo /dev/mtd*
+		- reg: the size and offset of this partition.
+		- (optional) read-only: an empty property flagging as read only
+
+Example:
+
+nand: flash@0 {
+	compatible = "brcm,bcm2835-smi-nand";
+	status = "okay";
+
+	partition@0 {
+		label = "stage2";
+		// 128k
+		reg = <0 0x20000>;
+		read-only;
+	};
+	partition@1 {
+		label = "firmware";
+		// 16M
+		reg = <0x20000 0x1000000>;
+		read-only;
+	};
+	partition@2 {
+		label = "root";
+		// 2G
+		reg = <0x1020000 0x80000000>;
+	};
+};

Documentation/devicetree/bindings/sound/brcm,bcm2835-i2s.txt

@@ -16,8 +16,8 @@ Example:
 
 bcm2835_i2s: i2s@7e203000 {
 	compatible = "brcm,bcm2835-i2s";
-	reg = <0x7e203000 0x20>,
-	      <0x7e101098 0x02>;
+	reg = <0x7e203000 0x24>,
+	      <0x7e101098 0x08>;
 
 	dmas = <&dma 2>,
 	       <&dma 3>;

Documentation/devicetree/configfs-overlays.txt

@@ -0,0 +1,31 @@
+Howto use the configfs overlay interface.
+
+A device-tree configfs entry is created in /config/device-tree/overlays
+and and it is manipulated using standard file system I/O.
+Note that this is a debug level interface, for use by developers and
+not necessarily something accessed by normal users due to the
+security implications of having direct access to the kernel's device tree.
+
+* To create an overlay you mkdir the directory:
+
+	# mkdir /config/device-tree/overlays/foo
+
+* Either you echo the overlay firmware file to the path property file.
+
+	# echo foo.dtbo >/config/device-tree/overlays/foo/path
+
+* Or you cat the contents of the overlay to the dtbo file
+
+	# cat foo.dtbo >/config/device-tree/overlays/foo/dtbo
+
+The overlay file will be applied, and devices will be created/destroyed
+as required.
+
+To remove it simply rmdir the directory.
+
+	# rmdir /config/device-tree/overlays/foo
+
+The rationalle of the dual interface (firmware & direct copy) is that each is
+better suited to different use patterns. The firmware interface is what's
+intended to be used by hardware managers in the kernel, while the copy interface
+make sense for developers (since it avoids problems with namespaces).

Documentation/filesystems/configfs/configfs.txt

@@ -51,15 +51,27 @@ configfs tree is always there, whether mounted on /config or not.
 An item is created via mkdir(2).  The item's attributes will also
 appear at this time.  readdir(3) can determine what the attributes are,
 read(2) can query their default values, and write(2) can store new
-values.  Like sysfs, attributes should be ASCII text files, preferably
-with only one value per file.  The same efficiency caveats from sysfs
-apply.  Don't mix more than one attribute in one attribute file.
+values.  Don't mix more than one attribute in one attribute file.
 
-Like sysfs, configfs expects write(2) to store the entire buffer at
-once.  When writing to configfs attributes, userspace processes should
-first read the entire file, modify the portions they wish to change, and
-then write the entire buffer back.  Attribute files have a maximum size
-of one page (PAGE_SIZE, 4096 on i386).
+There are two types of configfs attributes:
+
+* Normal attributes, which similar to sysfs attributes, are small ASCII text
+files, with a maximum size of one page (PAGE_SIZE, 4096 on i386).  Preferably
+only one value per file should be used, and the same caveats from sysfs apply.
+Configfs expects write(2) to store the entire buffer at once.  When writing to
+normal configfs attributes, userspace processes should first read the entire
+file, modify the portions they wish to change, and then write the entire
+buffer back.
+
+* Binary attributes, which are somewhat similar to sysfs binary attributes,
+but with a few slight changes to semantics.  The PAGE_SIZE limitation does not
+apply, but the whole binary item must fit in single kernel vmalloc'ed buffer.
+The write(2) calls from user space are buffered, and the attributes'
+write_bin_attribute method will be invoked on the final close, therefore it is
+imperative for user-space to check the return code of close(2) in order to
+verify that the operation finished successfully.
+To avoid a malicious user OOMing the kernel, there's a per-binary attribute
+maximum buffer value.
 
 When an item needs to be destroyed, remove it with rmdir(2).  An
 item cannot be destroyed if any other item has a link to it (via
@@ -171,6 +183,7 @@ among other things.  For that, it needs a type.
 		struct configfs_item_operations         *ct_item_ops;
 		struct configfs_group_operations        *ct_group_ops;
 		struct configfs_attribute               **ct_attrs;
+		struct configfs_bin_attribute		**ct_bin_attrs;
 	};
 
 The most basic function of a config_item_type is to define what
@@ -201,6 +214,32 @@ be called whenever userspace asks for a read(2) on the attribute.  If an
 attribute is writable and provides a ->store  method, that method will be
 be called whenever userspace asks for a write(2) on the attribute.
 
+[struct configfs_bin_attribute]
+
+	struct configfs_attribute {
+		struct configfs_attribute	cb_attr;
+		void				*cb_private;
+		size_t				cb_max_size;
+	};
+
+The binary attribute is used when the one needs to use binary blob to
+appear as the contents of a file in the item's configfs directory.
+To do so add the binary attribute to the NULL-terminated array
+config_item_type->ct_bin_attrs, and the item appears in configfs, the
+attribute file will appear with the configfs_bin_attribute->cb_attr.ca_name
+filename.  configfs_bin_attribute->cb_attr.ca_mode specifies the file
+permissions.
+The cb_private member is provided for use by the driver, while the
+cb_max_size member specifies the maximum amount of vmalloc buffer
+to be used.
+
+If binary attribute is readable and the config_item provides a
+ct_item_ops->read_bin_attribute() method, that method will be called
+whenever userspace asks for a read(2) on the attribute.  The converse
+will happen for write(2). The reads/writes are bufferred so only a
+single read/write will occur; the attributes' need not concern itself
+with it.
+
 [struct config_group]
 
 A config_item cannot live in a vacuum.  The only way one can be created

Documentation/serial/tty.txt

@@ -213,9 +213,6 @@ TTY_IO_ERROR		If set, causes all subsequent userspace read/write
 
 TTY_OTHER_CLOSED	Device is a pty and the other side has closed.
 
-TTY_OTHER_DONE		Device is a pty and the other side has closed and
-			all pending input processing has been completed.
-
 TTY_NO_WRITE_SPLIT	Prevent driver from splitting up writes into
 			smaller chunks.
 

Documentation/sysctl/fs.txt

@@ -32,6 +32,8 @@ Currently, these files are in /proc/sys/fs:
 - nr_open
 - overflowuid
 - overflowgid
+- pipe-user-pages-hard
+- pipe-user-pages-soft
 - protected_hardlinks
 - protected_symlinks
 - suid_dumpable
@@ -159,6 +161,27 @@ The default is 65534.
 
 ==============================================================
 
+pipe-user-pages-hard:
+
+Maximum total number of pages a non-privileged user may allocate for pipes.
+Once this limit is reached, no new pipes may be allocated until usage goes
+below the limit again. When set to 0, no limit is applied, which is the default
+setting.
+
+==============================================================
+
+pipe-user-pages-soft:
+
+Maximum total number of pages a non-privileged user may allocate for pipes
+before the pipe size gets limited to a single page. Once this limit is reached,
+new pipes will be limited to a single page in size for this user in order to
+limit total memory usage, and trying to increase them using fcntl() will be
+denied until usage goes below the limit again. The default value allows to
+allocate up to 1024 pipes at their default size. When set to 0, no limit is
+applied.
+
+==============================================================
+
 protected_hardlinks:
 
 A long-standing class of security issues is the hardlink-based

Documentation/video4linux/bcm2835-v4l2.txt

@@ -0,0 +1,60 @@
+
+BCM2835 (aka Raspberry Pi) V4L2 driver
+======================================
+
+1. Copyright
+============
+
+Copyright © 2013 Raspberry Pi (Trading) Ltd.
+
+2. License
+==========
+
+This program is free software; you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation; either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program; if not, write to the Free Software
+Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+
+3. Quick Start
+==============
+
+You need a version 1.0 or later of v4l2-ctl, available from:
+	git://git.linuxtv.org/v4l-utils.git
+
+$ sudo modprobe bcm2835-v4l2
+
+Turn on the overlay:
+
+$ v4l2-ctl --overlay=1
+
+Turn off the overlay:
+
+$ v4l2-ctl --overlay=0
+
+Set the capture format for video:
+
+$ v4l2-ctl  --set-fmt-video=width=1920,height=1088,pixelformat=4
+
+(Note: 1088 not 1080).
+
+Capture:
+
+$ v4l2-ctl --stream-mmap=3 --stream-count=100 --stream-to=somefile.h264
+
+Stills capture:
+
+$ v4l2-ctl  --set-fmt-video=width=2592,height=1944,pixelformat=3
+$ v4l2-ctl --stream-mmap=3 --stream-count=1 --stream-to=somefile.jpg
+
+List of available formats:
+
+$ v4l2-ctl --list-formats

MAINTAINERS

@@ -4097,8 +4097,8 @@ F:	Documentation/efi-stub.txt
 F:	arch/ia64/kernel/efi.c
 F:	arch/x86/boot/compressed/eboot.[ch]
 F:	arch/x86/include/asm/efi.h
-F:	arch/x86/platform/efi/*
-F:	drivers/firmware/efi/*
+F:	arch/x86/platform/efi/
+F:	drivers/firmware/efi/
 F:	include/linux/efi*.h
 
 EFI VARIABLE FILESYSTEM

Makefile

@@ -1,6 +1,6 @@
 VERSION = 4
 PATCHLEVEL = 4
-SUBLEVEL = 8
+SUBLEVEL = 14
 EXTRAVERSION =
 NAME = Blurry Fish Butt
 
@@ -364,7 +364,7 @@ AFLAGS_MODULE   =
 LDFLAGS_MODULE  =
 CFLAGS_KERNEL	=
 AFLAGS_KERNEL	=
-CFLAGS_GCOV	= -fprofile-arcs -ftest-coverage
+CFLAGS_GCOV	= -fprofile-arcs -ftest-coverage -fno-tree-loop-im
 
 
 # Use USERINCLUDE when you must reference the UAPI directories only.
@@ -682,9 +682,10 @@ KBUILD_CFLAGS += $(call cc-option, -mno-global-merge,)
 KBUILD_CFLAGS += $(call cc-option, -fcatch-undefined-behavior)
 else
 
-# This warning generated too much noise in a regular build.
-# Use make W=1 to enable this warning (see scripts/Makefile.build)
+# These warnings generated too much noise in a regular build.
+# Use make W=1 to enable them (see scripts/Makefile.build)
 KBUILD_CFLAGS += $(call cc-disable-warning, unused-but-set-variable)
+KBUILD_CFLAGS += $(call cc-disable-warning, unused-const-variable)
 endif
 
 ifdef CONFIG_FRAME_POINTER

arch/arc/include/asm/io.h

@@ -13,6 +13,15 @@
 #include <asm/byteorder.h>
 #include <asm/page.h>
 
+#ifdef CONFIG_ISA_ARCV2
+#include <asm/barrier.h>
+#define __iormb()		rmb()
+#define __iowmb()		wmb()
+#else
+#define __iormb()		do { } while (0)
+#define __iowmb()		do { } while (0)
+#endif
+
 extern void __iomem *ioremap(unsigned long physaddr, unsigned long size);
 extern void __iomem *ioremap_prot(phys_addr_t offset, unsigned long size,
 				  unsigned long flags);
@@ -22,6 +31,15 @@ extern void iounmap(const void __iomem *addr);
 #define ioremap_wc(phy, sz)		ioremap(phy, sz)
 #define ioremap_wt(phy, sz)		ioremap(phy, sz)
 
+/*
+ * io{read,write}{16,32}be() macros
+ */
+#define ioread16be(p)		({ u16 __v = be16_to_cpu((__force __be16)__raw_readw(p)); __iormb(); __v; })
+#define ioread32be(p)		({ u32 __v = be32_to_cpu((__force __be32)__raw_readl(p)); __iormb(); __v; })
+
+#define iowrite16be(v,p)	({ __iowmb(); __raw_writew((__force u16)cpu_to_be16(v), p); })
+#define iowrite32be(v,p)	({ __iowmb(); __raw_writel((__force u32)cpu_to_be32(v), p); })
+
 /* Change struct page to physical address */
 #define page_to_phys(page)		(page_to_pfn(page) << PAGE_SHIFT)
 
@@ -99,15 +117,6 @@ static inline void __raw_writel(u32 w, volatile void __iomem *addr)
 
 }
 
-#ifdef CONFIG_ISA_ARCV2
-#include <asm/barrier.h>
-#define __iormb()		rmb()
-#define __iowmb()		wmb()
-#else
-#define __iormb()		do { } while (0)
-#define __iowmb()		do { } while (0)
-#endif
-
 /*
  * MMIO can also get buffered/optimized in micro-arch, so barriers needed
  * Based on ARM model for the typical use case

arch/arm/Kconfig

@@ -317,6 +317,52 @@ choice
 	default ARCH_VERSATILE if !MMU
 	default ARCH_MULTIPLATFORM if MMU
 
+config ARCH_BCM2708
+	bool "Broadcom BCM2708 family"
+	select CPU_V6
+	select ARM_AMBA
+	select CLKSRC_MMIO
+	select CLKSRC_OF if OF
+	select HAVE_SCHED_CLOCK
+	select NEED_MACH_GPIO_H
+	select NEED_MACH_MEMORY_H
+	select COMMON_CLK
+	select ARCH_HAS_CPUFREQ
+	select GENERIC_CLOCKEVENTS
+	select ARM_ERRATA_411920
+	select MACH_BCM2708
+	select MULTI_IRQ_HANDLER
+	select SPARSE_IRQ
+	select VC4
+	select FIQ
+	help
+	  This enables support for Broadcom BCM2708 boards.
+
+config ARCH_BCM2709
+	bool "Broadcom BCM2709 family"
+	select CPU_V7
+	select HAVE_SMP
+	select ARM_AMBA
+	select MIGHT_HAVE_CACHE_L2X0
+	select HAVE_SCHED_CLOCK
+	select NEED_MACH_MEMORY_H
+	select NEED_MACH_IO_H
+	select COMMON_CLK
+	select ARCH_HAS_CPUFREQ
+	select GENERIC_CLOCKEVENTS
+	select MACH_BCM2709
+	select MULTI_IRQ_HANDLER
+	select SPARSE_IRQ
+	select MFD_SYSCON
+	select VC4
+	select FIQ
+	select USE_OF
+	select ARCH_REQUIRE_GPIOLIB
+	select PINCTRL
+	select PINCTRL_BCM2835
+	help
+	  This enables support for Broadcom BCM2709 boards.
+
 config ARCH_MULTIPLATFORM
 	bool "Allow multiple platforms to be selected"
 	depends on MMU
@@ -808,6 +854,9 @@ config ARCH_VIRT
 # Kconfigs may be included either alphabetically (according to the
 # plat- suffix) or along side the corresponding mach-* source.
 #
+source "arch/arm/mach-bcm2708/Kconfig"
+source "arch/arm/mach-bcm2709/Kconfig"
+
 source "arch/arm/mach-mvebu/Kconfig"
 
 source "arch/arm/mach-alpine/Kconfig"

arch/arm/Kconfig.debug

@@ -1240,6 +1240,14 @@ choice
 		  options; the platform specific options are deprecated
 		  and will be soon removed.
 
+	config DEBUG_BCM2708_UART0
+		bool "Broadcom BCM270X UART0 (PL011)"
+		depends on ARCH_BCM2708 || ARCH_BCM2709
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to UART 0. The port must have been initialised
+		  by the boot-loader before use.
+
 endchoice
 
 config DEBUG_EXYNOS_UART

arch/arm/Makefile

@@ -154,6 +154,8 @@ textofs-$(CONFIG_ARCH_AXXIA) := 0x00308000
 
 # Machine directory name.  This list is sorted alphanumerically
 # by CONFIG_* macro name.
+machine-$(CONFIG_ARCH_BCM2708)		+= bcm2708
+machine-$(CONFIG_ARCH_BCM2709)		+= bcm2709
 machine-$(CONFIG_ARCH_ALPINE)		+= alpine
 machine-$(CONFIG_ARCH_AT91)		+= at91
 machine-$(CONFIG_ARCH_AXXIA)		+= axxia

arch/arm/boot/.gitignore

@@ -3,4 +3,4 @@ zImage
 xipImage
 bootpImage
 uImage
-*.dtb
+*.dtb*

arch/arm/boot/dts/Makefile

@@ -1,5 +1,26 @@
 ifeq ($(CONFIG_OF),y)
 
+dtb-$(CONFIG_ARCH_BCM2708) += bcm2708-rpi-b.dtb
+dtb-$(CONFIG_ARCH_BCM2708) += bcm2708-rpi-b-plus.dtb
+dtb-$(CONFIG_ARCH_BCM2708) += bcm2708-rpi-cm.dtb
+dtb-$(CONFIG_ARCH_BCM2835) += bcm2835-rpi-cm.dtb
+dtb-$(CONFIG_ARCH_BCM2709) += bcm2709-rpi-2-b.dtb
+dtb-$(CONFIG_ARCH_BCM2709) += bcm2710-rpi-3-b.dtb
+
+# Raspberry Pi
+ifeq ($(CONFIG_ARCH_BCM2708),y)
+   RPI_DT_OVERLAYS=y
+endif
+ifeq ($(CONFIG_ARCH_BCM2709),y)
+   RPI_DT_OVERLAYS=y
+endif
+ifeq ($(CONFIG_ARCH_BCM2835),y)
+   RPI_DT_OVERLAYS=y
+endif
+ifeq ($(RPI_DT_OVERLAYS),y)
+    dts-dirs += overlays
+endif
+
 dtb-$(CONFIG_ARCH_ALPINE) += \
 	alpine-db.dtb
 dtb-$(CONFIG_MACH_ASM9260) += \
@@ -777,10 +798,20 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += \
 	mt8127-moose.dtb \
 	mt8135-evbp1.dtb
 dtb-$(CONFIG_ARCH_ZX) += zx296702-ad1.dtb
+
+targets += dtbs dtbs_install
+targets += $(dtb-y)
+
 endif
 
 dtstree		:= $(srctree)/$(src)
 dtb-$(CONFIG_OF_ALL_DTBS) := $(patsubst $(dtstree)/%.dts,%.dtb, $(wildcard $(dtstree)/*.dts))
 
 always		:= $(dtb-y)
+subdir-y	:= $(dts-dirs)
 clean-files	:= *.dtb
+
+# Enable fixups to support overlays on BCM2708 platforms
+ifeq ($(RPI_DT_OVERLAYS),y)
+	DTC_FLAGS ?= -@ -H epapr
+endif

arch/arm/boot/dts/am43x-epos-evm.dts

@@ -792,3 +792,8 @@
 	tx-num-evt = <32>;
 	rx-num-evt = <32>;
 };
+
+&synctimer_32kclk {
+	assigned-clocks = <&mux_synctimer32k_ck>;
+	assigned-clock-parents = <&clkdiv32k_ick>;
+};

arch/arm/boot/dts/armada-375.dtsi

@@ -529,7 +529,7 @@
 			};
 
 			sata@a0000 {
-				compatible = "marvell,orion-sata";
+				compatible = "marvell,armada-370-sata";
 				reg = <0xa0000 0x5000>;
 				interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&gateclk 14>, <&gateclk 20>;

arch/arm/boot/dts/armada-385-linksys.dtsi

@@ -117,7 +117,7 @@
 			};
 
 			/* USB part of the eSATA/USB 2.0 port */
-			usb@50000 {
+			usb@58000 {
 				status = "okay";
 			};
 
@@ -245,7 +245,7 @@
 		button@2 {
 			label = "Factory Reset Button";
 			linux,code = <KEY_RESTART>;
-			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+			gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
 		};
 	};
 
@@ -260,7 +260,7 @@
 		};
 
 		sata {
-			gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>;
+			gpios = <&gpio1 22 GPIO_ACTIVE_LOW>;
 			default-state = "off";
 		};
 	};
@@ -313,7 +313,7 @@
 
 &pinctrl {
 	keys_pin: keys-pin {
-		marvell,pins = "mpp24", "mpp47";
+		marvell,pins = "mpp24", "mpp29";
 		marvell,function = "gpio";
 	};
 

arch/arm/boot/dts/armada-xp-linksys-mamba.dts

@@ -304,13 +304,13 @@
 		button@1 {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
-			gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+			gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
 		};
 
 		button@2 {
 			label = "Factory Reset Button";
 			linux,code = <KEY_RESTART>;
-			gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
+			gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
 		};
 	};
 

arch/arm/boot/dts/at91sam9x5.dtsi

@@ -106,7 +106,7 @@
 
 			pmc: pmc@fffffc00 {
 				compatible = "atmel,at91sam9x5-pmc", "syscon";
-				reg = <0xfffffc00 0x100>;
+				reg = <0xfffffc00 0x200>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				interrupt-controller;
 				#address-cells = <1>;

arch/arm/boot/dts/bcm2708-rpi-b-plus.dts

@@ -0,0 +1,154 @@
+/dts-v1/;
+
+#include "bcm2708.dtsi"
+
+/ {
+	compatible = "brcm,bcm2708";
+	model = "Raspberry Pi Model B+";
+};
+
+&gpio {
+	sdhost_pins: sdhost_pins {
+		brcm,pins = <48 49 50 51 52 53>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <4>; /* alt0 */
+	};
+};
+
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_pins>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&fb {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev0: spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <500000>;
+	};
+
+	spidev1: spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <500000>;
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	#sound-dai-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&random {
+	status = "okay";
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&gpio 47 0>;
+	};
+
+	pwr_led: pwr {
+		label = "led1";
+		linux,default-trigger = "input";
+		gpios = <&gpio 35 0>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+};
+
+/ {
+	__overrides__ {
+		uart0 = <&uart0>,"status";
+		uart0_clkrate = <&clk_uart0>,"clock-frequency:0";
+		uart1 = <&uart1>,"status";
+		i2s = <&i2s>,"status";
+		spi = <&spi0>,"status";
+		i2c0 = <&i2c0>,"status";
+		i2c1 = <&i2c1>,"status";
+		i2c2_iknowwhatimdoing = <&i2c2>,"status";
+		i2c0_baudrate = <&i2c0>,"clock-frequency:0";
+		i2c1_baudrate = <&i2c1>,"clock-frequency:0";
+		i2c2_baudrate = <&i2c2>,"clock-frequency:0";
+		core_freq = <&clk_core>,"clock-frequency:0";
+
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+
+		pwr_led_gpio = <&pwr_led>,"gpios:4";
+		pwr_led_activelow = <&pwr_led>,"gpios:8";
+		pwr_led_trigger = <&pwr_led>,"linux,default-trigger";
+
+		audio = <&audio>,"status";
+		watchdog = <&watchdog>,"status";
+		random = <&random>,"status";
+		sd_overclock = <&sdhost>,"brcm,overclock-50:0";
+		sd_force_pio = <&sdhost>,"brcm,force-pio?";
+		sd_pio_limit = <&sdhost>,"brcm,pio-limit:0";
+		sd_debug     = <&sdhost>,"brcm,debug";
+	};
+};

arch/arm/boot/dts/bcm2708-rpi-b.dts

@@ -0,0 +1,144 @@
+/dts-v1/;
+
+#include "bcm2708.dtsi"
+
+/ {
+	compatible = "brcm,bcm2708";
+	model = "Raspberry Pi Model B";
+};
+
+&gpio {
+	sdhost_pins: sdhost_pins {
+		brcm,pins = <48 49 50 51 52 53>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <28 29 30 31>;
+		brcm,function = <6>; /* alt2 */
+	};
+};
+
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_pins>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&fb {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev0: spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <500000>;
+	};
+
+	spidev1: spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <500000>;
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	#sound-dai-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&random {
+	status = "okay";
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&gpio 16 1>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
+};
+
+/ {
+	__overrides__ {
+		uart0 = <&uart0>,"status";
+		uart0_clkrate = <&clk_uart0>,"clock-frequency:0";
+		uart1 = <&uart1>,"status";
+		i2s = <&i2s>,"status";
+		spi = <&spi0>,"status";
+		i2c0 = <&i2c0>,"status";
+		i2c1 = <&i2c1>,"status";
+		i2c2_iknowwhatimdoing = <&i2c2>,"status";
+		i2c0_baudrate = <&i2c0>,"clock-frequency:0";
+		i2c1_baudrate = <&i2c1>,"clock-frequency:0";
+		i2c2_baudrate = <&i2c2>,"clock-frequency:0";
+		core_freq = <&clk_core>,"clock-frequency:0";
+
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+
+		audio = <&audio>,"status";
+		watchdog = <&watchdog>,"status";
+		random = <&random>,"status";
+		sd_overclock = <&sdhost>,"brcm,overclock-50:0";
+		sd_force_pio = <&sdhost>,"brcm,force-pio?";
+		sd_pio_limit = <&sdhost>,"brcm,pio-limit:0";
+		sd_debug     = <&sdhost>,"brcm,debug";
+	};
+};

arch/arm/boot/dts/bcm2708-rpi-cm.dts

@@ -0,0 +1,102 @@
+/dts-v1/;
+
+#include "bcm2708-rpi-cm.dtsi"
+
+/ {
+	model = "Raspberry Pi Compute Module";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&gpio {
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <4>; /* alt0 */
+	};
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev0: spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <500000>;
+	};
+
+	spidev1: spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <500000>;
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	#sound-dai-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&random {
+	status = "okay";
+};
+
+/ {
+	__overrides__ {
+		uart0 = <&uart0>,"status";
+		uart0_clkrate = <&clk_uart0>,"clock-frequency:0";
+		uart1 = <&uart1>,"status";
+		i2s = <&i2s>,"status";
+		spi = <&spi0>,"status";
+		i2c0 = <&i2c0>,"status";
+		i2c1 = <&i2c1>,"status";
+		i2c2_iknowwhatimdoing = <&i2c2>,"status";
+		i2c0_baudrate = <&i2c0>,"clock-frequency:0";
+		i2c1_baudrate = <&i2c1>,"clock-frequency:0";
+		i2c2_baudrate = <&i2c2>,"clock-frequency:0";
+	};
+};

arch/arm/boot/dts/bcm2708-rpi-cm.dtsi

@@ -0,0 +1,52 @@
+#include "bcm2708.dtsi"
+
+&gpio {
+	sdhost_pins: sdhost_pins {
+		brcm,pins = <48 49 50 51 52 53>;
+		brcm,function = <4>; /* alt0 */
+	};
+};
+
+&gpio {
+	mmc_pins: mmc_pins {
+		brcm,pins = <48 49 50 51 52 53>;
+		brcm,function = <7>; /* alt3 */
+	};
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&gpio 47 0>;
+	};
+};
+
+
+&mmc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc_pins>;
+	non-removable;
+	bus-width = <4>;
+	status = "okay";
+	brcm,overclock-50 = <0>;
+};
+
+&fb {
+	status = "okay";
+};
+
+/ {
+	__overrides__ {
+		core_freq = <&clk_core>,"clock-frequency:0";
+
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+
+		audio = <&audio>,"status";
+		watchdog = <&watchdog>,"status";
+		random = <&random>,"status";
+		sd_overclock = <&mmc>,"brcm,overclock-50:0";
+	};
+};

arch/arm/boot/dts/bcm2708.dtsi

@@ -0,0 +1,40 @@
+#include "bcm2708_common.dtsi"
+
+/ {
+	compatible = "brcm,bcm2708";
+	model = "BCM2708";
+
+	chosen {
+		/* No padding required - the boot loader can do that. */
+		bootargs = "";
+	};
+
+	soc {
+		ranges = <0x7e000000 0x20000000 0x01000000>;
+
+		timer@7e003000 {
+			compatible = "brcm,bcm2835-system-timer";
+			reg = <0x7e003000 0x1000>;
+			interrupts = <1 0>, <1 1>, <1 2>, <1 3>;
+			clock-frequency = <1000000>;
+		};
+
+		arm-pmu {
+			compatible = "arm,arm1176-pmu";
+		};
+
+		gpiomem {
+			compatible = "brcm,bcm2835-gpiomem";
+			reg = <0x7e200000 0x1000>;
+			status = "okay";
+		};
+	};
+};
+
+&intc {
+	compatible = "brcm,bcm2835-armctrl-ic";
+};
+
+&watchdog {
+	status = "okay";
+};

arch/arm/boot/dts/bcm2708_common.dtsi

@@ -0,0 +1,471 @@
+#include "dt-bindings/clock/bcm2835.h"
+#include <dt-bindings/clock/bcm2835-aux.h>
+#include "dt-bindings/power/raspberrypi-power.h"
+#include "dt-bindings/gpio/gpio.h"
+#include "skeleton.dtsi"
+
+/ {
+	interrupt-parent = <&intc>;
+
+	aliases {
+		audio = &audio;
+		aux = &aux;
+		sound = &sound;
+		soc = &soc;
+		dma = &dma;
+		intc = &intc;
+		watchdog = &watchdog;
+		random = &random;
+		mailbox = &mailbox;
+		gpio = &gpio;
+		uart0 = &uart0;
+		sdhost = &sdhost;
+		i2s  = &i2s;
+		spi0 = &spi0;
+		i2c0 = &i2c0;
+		uart1 = &uart1;
+		spi1 = &spi1;
+		spi2 = &spi2;
+		mmc = &mmc;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		usb = &usb;
+		leds = &leds;
+		fb = &fb;
+		vchiq = &vchiq;
+		thermal = &thermal;
+		clocks = &clocks;
+	};
+
+	soc: soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		dma: dma@7e007000 {
+			compatible = "brcm,bcm2835-dma";
+			reg = <0x7e007000 0xf00>;
+			interrupts = <1 16>,
+				     <1 17>,
+				     <1 18>,
+				     <1 19>,
+				     <1 20>,
+				     <1 21>,
+				     <1 22>,
+				     <1 23>,
+				     <1 24>,
+				     <1 25>,
+				     <1 26>,
+				     /* dma channel 11-14 share one irq */
+				     <1 27>,
+				     <1 27>,
+				     <1 27>,
+				     <1 27>,
+				     /* unused shared irq for all channels */
+				     <1 28>;
+			interrupt-names = "dma0",
+					  "dma1",
+					  "dma2",
+					  "dma3",
+					  "dma4",
+					  "dma5",
+					  "dma6",
+					  "dma7",
+					  "dma8",
+					  "dma9",
+					  "dma10",
+					  "dma11",
+					  "dma12",
+					  "dma13",
+					  "dma14",
+					  "dma-shared-all";
+
+			#dma-cells = <1>;
+			brcm,dma-channel-mask = <0x7f34>;
+		};
+
+		intc: interrupt-controller@7e00b200 {
+			compatible = "brcm,bcm2708-armctrl-ic";
+			reg = <0x7e00b200 0x200>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		mailbox: mailbox@7e00b800 {
+			compatible = "brcm,bcm2835-mbox";
+			reg = <0x7e00b880 0x40>;
+			interrupts = <0 1>;
+			#mbox-cells = <0>;
+		};
+
+		watchdog: watchdog@7e100000 {
+			compatible = "brcm,bcm2835-pm-wdt";
+			reg = <0x7e100000 0x28>;
+			status = "disabled";
+		};
+
+		cprman: cprman@7e101000 {
+			compatible = "brcm,bcm2835-cprman";
+			#clock-cells = <1>;
+			reg = <0x7e101000 0x2000>;
+
+			/* CPRMAN derives everything from the platform's
+			 * oscillator.
+			 */
+			clocks = <&clk_osc>;
+			status = "disabled";
+		};
+
+		random: rng@7e104000 {
+			compatible = "brcm,bcm2835-rng";
+			reg = <0x7e104000 0x10>;
+			status = "disabled";
+		};
+
+		gpio: gpio@7e200000 {
+			compatible = "brcm,bcm2835-gpio";
+			reg = <0x7e200000 0xb4>;
+			interrupts = <2 17>, <2 18>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		uart0: uart@7e201000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x7e201000 0x1000>;
+			interrupts = <2 25>;
+			clocks = <&clk_uart0 &clk_apb_p>;
+			clock-names = "uartclk","apb_pclk";
+			arm,primecell-periphid = <0x00241011>; // For an explanation, see
+			// https://github.com/raspberrypi/linux/commit/13731d862cf5219216533a3b0de052cee4cc5038
+			status = "disabled";
+		};
+
+		sdhost: sdhost@7e202000 {
+			compatible = "brcm,bcm2835-sdhost";
+			reg = <0x7e202000 0x100>;
+			interrupts = <2 24>;
+			clocks = <&clk_core>;
+			dmas = <&dma 13>;
+			dma-names = "rx-tx";
+			brcm,overclock-50 = <0>;
+			brcm,pio-limit = <1>;
+			status = "disabled";
+		};
+
+		i2s: i2s@7e203000 {
+			compatible = "brcm,bcm2835-i2s";
+			#sound-dai-cells = <0>;
+			reg = <0x7e203000 0x24>,
+			      <0x7e101098 0x08>;
+
+			dmas = <&dma 2>, <&dma 3>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		spi0: spi@7e204000 {
+			compatible = "brcm,bcm2835-spi";
+			reg = <0x7e204000 0x1000>;
+			interrupts = <2 22>;
+			clocks = <&clk_core>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+			/* the dma channels */
+			dmas = <&dma 6>, <&dma 7>;
+			dma-names = "tx", "rx";
+			/* the chipselects used - <0> means native GPIO
+			 * add more gpios if necessary as <&gpio 6 1>
+			 * (but do not forget to make them output!)
+			 */
+			cs-gpios = <0>, <0>;
+		};
+
+		i2c0: i2c@7e205000 {
+			compatible = "brcm,bcm2708-i2c";
+			reg = <0x7e205000 0x1000>;
+			interrupts = <2 21>;
+			clocks = <&clk_core>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		pixelvalve0: pixelvalve@7e206000 {
+			compatible = "brcm,bcm2835-pixelvalve0";
+			reg = <0x7e206000 0x100>;
+			status = "disabled";
+		};
+
+		dpi: dpi@7e208000 {
+			compatible = "brcm,bcm2835-dpi";
+			reg = <0x7e208000 0x8c>;
+			clocks = <&cprman BCM2835_CLOCK_VPU>,
+				 <&cprman BCM2835_CLOCK_DPI>;
+			clock-names = "core", "pixel";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		pixelvalve1: pixelvalve@7e207000 {
+			compatible = "brcm,bcm2835-pixelvalve1";
+			reg = <0x7e207000 0x100>;
+			status = "disabled";
+		};
+
+		pwm: pwm@7e20c000 {
+			compatible = "brcm,bcm2835-pwm";
+			reg = <0x7e20c000 0x28>;
+			clocks = <&clk_pwm>;
+			#pwm-cells = <2>;
+			status = "disabled";
+		};
+
+		aux: aux@0x7e215004 {
+			compatible = "brcm,bcm2835-aux";
+			#clock-cells = <1>;
+			reg = <0x7e215000 0x8>;
+			clocks = <&clk_core>;
+			status = "disabled";
+		};
+
+		uart1: uart@7e215040 {
+			compatible = "brcm,bcm2835-aux-uart", "ns16550";
+			reg = <0x7e215040 0x40>;
+			interrupts = <1 29>;
+			clocks = <&clk_uart1>;
+			reg-shift = <2>;
+			no-loopback-test;
+			status = "disabled";
+		};
+
+		spi1: spi@7e215080 {
+			compatible = "brcm,bcm2835-aux-spi";
+			reg = <0x7e215080 0x40>, <0x7e215000 0x8>;
+			interrupts = <1 29>;
+			clocks = <&aux BCM2835_AUX_CLOCK_SPI1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		spi2: spi@7e2150C0 {
+			compatible = "brcm,bcm2835-aux-spi";
+			reg = <0x7e2150C0 0x40>, <0x7e215000 0x8>;
+			interrupts = <1 29>;
+			clocks = <&aux BCM2835_AUX_CLOCK_SPI2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		mmc: mmc@7e300000 {
+			compatible = "brcm,bcm2835-mmc";
+			reg = <0x7e300000 0x100>;
+			interrupts = <2 30>;
+			clocks = <&clk_mmc>;
+			dmas = <&dma 11>;
+			dma-names = "rx-tx";
+			brcm,overclock-50 = <0>;
+			status = "disabled";
+		};
+
+		hvs: hvs@7e400000 {
+			compatible = "brcm,bcm2835-hvs";
+			reg = <0x7e400000 0x6000>;
+			status = "disabled";
+		};
+
+		i2c1: i2c@7e804000 {
+			compatible = "brcm,bcm2708-i2c";
+			reg = <0x7e804000 0x1000>;
+			interrupts = <2 21>;
+			clocks = <&clk_core>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c2: i2c@7e805000 {
+			// Beware - this is shared with the HDMI module.
+			// Careless use may break (really) your display.
+			// Caveat emptor.
+			compatible = "brcm,bcm2708-i2c";
+			reg = <0x7e805000 0x1000>;
+			interrupts = <2 21>;
+			clocks = <&clk_core>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		smi: smi@7e600000 {
+			compatible = "brcm,bcm2835-smi";
+			reg = <0x7e600000 0x44>, <0x7e1010b0 0x8>;
+			interrupts = <2 16>;
+			brcm,smi-clock-source = <6>;
+			brcm,smi-clock-divisor = <4>;
+			dmas = <&dma 4>;
+			dma-names = "rx-tx";
+			status = "disabled";
+		};
+
+		pixelvalve2: pixelvalve@7e807000 {
+			compatible = "brcm,bcm2835-pixelvalve2";
+			reg = <0x7e807000 0x100>;
+			status = "disabled";
+		};
+
+		hdmi: hdmi@7e902000 {
+			compatible = "brcm,bcm2835-hdmi";
+			reg = <0x7e902000 0x600>,
+			      <0x7e808000 0x100>;
+			ddc = <&i2c2>;
+			hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
+			clocks = <&cprman BCM2835_PLLH_PIX>,
+				 <&cprman BCM2835_CLOCK_HSM>;
+			clock-names = "pixel", "hdmi";
+			power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+			status = "disabled";
+		};
+
+		usb: usb@7e980000 {
+			compatible = "brcm,bcm2708-usb";
+			reg = <0x7e980000 0x10000>,
+			      <0x7e006000 0x1000>;
+			interrupts = <2 0>,
+				     <1 9>;
+		};
+
+		v3d: v3d@7ec00000 {
+			compatible = "brcm,vc4-v3d";
+			reg = <0x7ec00000 0x1000>;
+			status = "disabled";
+		};
+
+		firmware: firmware {
+			compatible = "raspberrypi,bcm2835-firmware";
+			mboxes = <&mailbox>;
+		};
+
+		power: power {
+			compatible = "raspberrypi,bcm2835-power";
+			firmware = <&firmware>;
+			#power-domain-cells = <1>;
+		};
+
+		leds: leds {
+			compatible = "gpio-leds";
+		};
+
+		fb: fb {
+			compatible = "brcm,bcm2708-fb";
+			firmware = <&firmware>;
+			status = "disabled";
+		};
+
+		vchiq: vchiq {
+			compatible = "brcm,bcm2835-vchiq";
+			reg = <0x7e00b840 0xf>;
+			interrupts = <0 2>;
+			cache-line-size = <32>;
+			firmware = <&firmware>;
+		};
+
+		thermal: thermal {
+			compatible = "brcm,bcm2835-thermal";
+			firmware = <&firmware>;
+		};
+
+		gpu: gpu {
+			compatible = "brcm,bcm2835-vc4";
+			status = "disabled";
+		};
+
+		/* Onboard audio */
+		audio: audio {
+			compatible = "brcm,bcm2835-audio";
+			brcm,pwm-channels = <8>;
+			status = "disabled";
+		};
+
+		/* External sound card */
+		sound: sound {
+			status = "disabled";
+		};
+	};
+
+	clocks: clocks {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		clk_core: clock@0 {
+			compatible = "fixed-clock";
+			reg = <0>;
+			#clock-cells = <0>;
+			clock-output-names = "core";
+			clock-frequency = <250000000>;
+		};
+
+		clk_mmc: clock@1 {
+			compatible = "fixed-clock";
+			reg = <1>;
+			#clock-cells = <0>;
+			clock-output-names = "mmc";
+			clock-frequency = <250000000>;
+		};
+
+		clk_uart0: clock@2 {
+			compatible = "fixed-clock";
+			reg = <2>;
+			#clock-cells = <0>;
+			clock-output-names = "uart0_pclk";
+			clock-frequency = <3000000>;
+		};
+
+		clk_apb_p: clock@3 {
+			compatible = "fixed-clock";
+			reg = <3>;
+			#clock-cells = <0>;
+			clock-output-names = "apb_pclk";
+			clock-frequency = <126000000>;
+		};
+
+		clk_pwm: clock@4 {
+			compatible = "fixed-clock";
+			reg = <4>;
+			#clock-cells = <0>;
+			clock-output-names = "pwm";
+			clock-frequency = <100000000>;
+		};
+
+		clk_uart1: clock@5 {
+			compatible = "fixed-factor-clock";
+			reg = <5>;
+			clocks = <&clk_core>;
+			#clock-cells = <0>;
+			clock-div = <1>;
+			clock-mult = <2>;
+		};
+
+		/* The oscillator is the root of the clock tree. */
+		clk_osc: clock@6 {
+			compatible = "fixed-clock";
+			reg = <6>;
+			#clock-cells = <0>;
+			clock-output-names = "osc";
+			clock-frequency = <19200000>;
+		};
+	};
+
+	__overrides__ {
+		cache_line_size = <&vchiq>, "cache-line-size:0";
+	};
+};

arch/arm/boot/dts/bcm2709-rpi-2-b.dts

@@ -0,0 +1,154 @@
+/dts-v1/;
+
+#include "bcm2709.dtsi"
+
+/ {
+	compatible = "brcm,bcm2709";
+	model = "Raspberry Pi 2 Model B";
+};
+
+&gpio {
+	sdhost_pins: sdhost_pins {
+		brcm,pins = <48 49 50 51 52 53>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <4>; /* alt0 */
+	};
+};
+
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_pins>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&fb {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev0: spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <500000>;
+	};
+
+	spidev1: spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <500000>;
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	#sound-dai-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&random {
+	status = "okay";
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&gpio 47 0>;
+	};
+
+	pwr_led: pwr {
+		label = "led1";
+		linux,default-trigger = "input";
+		gpios = <&gpio 35 0>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+};
+
+/ {
+	__overrides__ {
+		uart0 = <&uart0>,"status";
+		uart0_clkrate = <&clk_uart0>,"clock-frequency:0";
+		uart1 = <&uart1>,"status";
+		i2s = <&i2s>,"status";
+		spi = <&spi0>,"status";
+		i2c0 = <&i2c0>,"status";
+		i2c1 = <&i2c1>,"status";
+		i2c2_iknowwhatimdoing = <&i2c2>,"status";
+		i2c0_baudrate = <&i2c0>,"clock-frequency:0";
+		i2c1_baudrate = <&i2c1>,"clock-frequency:0";
+		i2c2_baudrate = <&i2c2>,"clock-frequency:0";
+		core_freq = <&clk_core>,"clock-frequency:0";
+
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+
+		pwr_led_gpio = <&pwr_led>,"gpios:4";
+		pwr_led_activelow = <&pwr_led>,"gpios:8";
+		pwr_led_trigger = <&pwr_led>,"linux,default-trigger";
+
+		audio = <&audio>,"status";
+		watchdog = <&watchdog>,"status";
+		random = <&random>,"status";
+		sd_overclock = <&sdhost>,"brcm,overclock-50:0";
+		sd_force_pio = <&sdhost>,"brcm,force-pio?";
+		sd_pio_limit = <&sdhost>,"brcm,pio-limit:0";
+		sd_debug     = <&sdhost>,"brcm,debug";
+	};
+};

arch/arm/boot/dts/bcm2709.dtsi

@@ -0,0 +1,102 @@
+#include "bcm2708_common.dtsi"
+
+/ {
+	compatible = "brcm,bcm2709";
+	model = "BCM2709";
+
+	chosen {
+		/* No padding required - the boot loader can do that. */
+		bootargs = "";
+	};
+
+	soc {
+		ranges = <0x7e000000 0x3f000000 0x01000000>,
+		         <0x40000000 0x40000000 0x00040000>;
+
+		local_intc: local_intc {
+			compatible = "brcm,bcm2836-l1-intc";
+			reg = <0x40000000 0x100>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&local_intc>;
+		};
+
+		arm-pmu {
+			compatible = "arm,cortex-a7-pmu";
+			interrupt-parent = <&local_intc>;
+			interrupts = <9>;
+		};
+
+		gpiomem {
+			compatible = "brcm,bcm2835-gpiomem";
+			reg = <0x7e200000 0x1000>;
+			status = "okay";
+		};
+
+		timer {
+			compatible = "arm,armv7-timer";
+			clock-frequency = <19200000>;
+			interrupt-parent = <&local_intc>;
+			interrupts = <0>, // PHYS_SECURE_PPI
+				     <1>, // PHYS_NONSECURE_PPI
+				     <3>, // VIRT_PPI
+				     <2>; // HYP_PPI
+			always-on;
+		};
+
+		syscon@40000000 {
+			compatible = "brcm,bcm2836-arm-local", "syscon";
+			reg = <0x40000000 0x100>;
+		};
+	};
+
+	cpus: cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		v7_cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0xf00>;
+			clock-frequency = <800000000>;
+		};
+
+		v7_cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0xf01>;
+			clock-frequency = <800000000>;
+		};
+
+		v7_cpu2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0xf02>;
+			clock-frequency = <800000000>;
+		};
+
+		v7_cpu3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0xf03>;
+			clock-frequency = <800000000>;
+		};
+	};
+
+	__overrides__ {
+		arm_freq = <&v7_cpu0>, "clock-frequency:0",
+		       <&v7_cpu1>, "clock-frequency:0",
+		       <&v7_cpu2>, "clock-frequency:0",
+		       <&v7_cpu3>, "clock-frequency:0";
+	};
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&intc {
+        compatible = "brcm,bcm2836-armctrl-ic";
+        interrupt-parent = <&local_intc>;
+        interrupts = <8>;
+};

arch/arm/boot/dts/bcm2710-rpi-3-b.dts

@@ -0,0 +1,201 @@
+/dts-v1/;
+
+#include "bcm2710.dtsi"
+
+/ {
+	compatible = "brcm,bcm2710","brcm,bcm2709";
+	model = "Raspberry Pi 3 Model B";
+};
+
+&gpio {
+	sdhost_pins: sdhost_pins {
+		brcm,pins = <48 49 50 51 52 53>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	sdio_pins: sdio_pins {
+		brcm,pins =     <34 35 36 37 38 39>;
+		brcm,function = <7>; // alt3 = SD1
+		brcm,pull =     <0 2 2 2 2 2>;
+	};
+
+	bt_pins: bt_pins {
+		brcm,pins = <43>;
+		brcm,function = <4>; /* alt0:GPCLK2 */
+		brcm,pull = <0>;
+	};
+
+	uart0_pins: uart0_pins {
+		brcm,pins = <32 33>;
+		brcm,function = <7>; /* alt3=UART0 */
+		brcm,pull = <0 2>;
+	};
+
+	uart1_pins: uart1_pins {
+		brcm,pins;
+		brcm,function;
+		brcm,pull;
+	};
+};
+
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_pins>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&mmc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdio_pins>;
+	non-removable;
+	bus-width = <4>;
+	status = "okay";
+	brcm,overclock-50 = <0>;
+};
+
+&soc {
+	virtgpio: virtgpio {
+		compatible = "brcm,bcm2835-virtgpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		firmware = <&firmware>;
+		status = "okay";
+	};
+};
+
+&fb {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins &bt_pins>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev0: spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <500000>;
+	};
+
+	spidev1: spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <500000>;
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	#sound-dai-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&random {
+	status = "okay";
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&virtgpio 0 0>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+};
+
+/ {
+	chosen {
+		bootargs = "8250.nr_uarts=1";
+	};
+};
+
+/ {
+	__overrides__ {
+		uart0 = <&uart0>,"status";
+		uart0_clkrate = <&clk_uart0>,"clock-frequency:0";
+		uart1 = <&uart1>,"status";
+		i2s = <&i2s>,"status";
+		spi = <&spi0>,"status";
+		i2c0 = <&i2c0>,"status";
+		i2c1 = <&i2c1>,"status";
+		i2c2_iknowwhatimdoing = <&i2c2>,"status";
+		i2c0_baudrate = <&i2c0>,"clock-frequency:0";
+		i2c1_baudrate = <&i2c1>,"clock-frequency:0";
+		i2c2_baudrate = <&i2c2>,"clock-frequency:0";
+		core_freq = <&clk_core>,"clock-frequency:0";
+
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+
+		audio = <&audio>,"status";
+		watchdog = <&watchdog>,"status";
+		random = <&random>,"status";
+		sd_overclock = <&sdhost>,"brcm,overclock-50:0";
+		sd_force_pio = <&sdhost>,"brcm,force-pio?";
+		sd_pio_limit = <&sdhost>,"brcm,pio-limit:0";
+		sd_debug     = <&sdhost>,"brcm,debug";
+	};
+};

arch/arm/boot/dts/bcm2710.dtsi

@@ -0,0 +1,102 @@
+#include "bcm2708_common.dtsi"
+
+/ {
+	compatible = "brcm,bcm2710","brcm,bcm2709";
+	model = "BCM2710";
+
+	chosen {
+		/* No padding required - the boot loader can do that. */
+		bootargs = "";
+	};
+
+	soc {
+		ranges = <0x7e000000 0x3f000000 0x01000000>,
+		         <0x40000000 0x40000000 0x00040000>;
+
+		local_intc: local_intc {
+			compatible = "brcm,bcm2836-l1-intc";
+			reg = <0x40000000 0x100>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&local_intc>;
+		};
+
+		arm-pmu {
+			compatible = "arm,cortex-a7-pmu";
+			interrupt-parent = <&local_intc>;
+			interrupts = <9>;
+		};
+
+		gpiomem {
+			compatible = "brcm,bcm2835-gpiomem";
+			reg = <0x7e200000 0x1000>;
+			status = "okay";
+		};
+
+		timer {
+			compatible = "arm,armv7-timer";
+			clock-frequency = <19200000>;
+			interrupt-parent = <&local_intc>;
+			interrupts = <0>, // PHYS_SECURE_PPI
+				     <1>, // PHYS_NONSECURE_PPI
+				     <3>, // VIRT_PPI
+				     <2>; // HYP_PPI
+			always-on;
+		};
+
+		syscon@40000000 {
+			compatible = "brcm,bcm2836-arm-local", "syscon";
+			reg = <0x40000000 0x100>;
+		};
+	};
+
+	cpus: cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		v7_cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x000>;
+			clock-frequency = <800000000>;
+		};
+
+		v7_cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x001>;
+			clock-frequency = <800000000>;
+		};
+
+		v7_cpu2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x002>;
+			clock-frequency = <800000000>;
+		};
+
+		v7_cpu3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x003>;
+			clock-frequency = <800000000>;
+		};
+	};
+
+	__overrides__ {
+		arm_freq = <&v7_cpu0>, "clock-frequency:0",
+		       <&v7_cpu1>, "clock-frequency:0",
+		       <&v7_cpu2>, "clock-frequency:0",
+		       <&v7_cpu3>, "clock-frequency:0";
+	};
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&intc {
+        compatible = "brcm,bcm2836-armctrl-ic";
+        interrupt-parent = <&local_intc>;
+        interrupts = <8>;
+};

arch/arm/boot/dts/bcm2835-rpi-b-plus.dts

@@ -1,30 +1,128 @@
 /dts-v1/;
-#include "bcm2835-rpi.dtsi"
+#include "bcm2835.dtsi"
 
 / {
 	compatible = "raspberrypi,model-b-plus", "brcm,bcm2835";
 	model = "Raspberry Pi Model B+";
-
-	leds {
-		act {
-			gpios = <&gpio 47 0>;
-		};
-
-		pwr {
-			label = "PWR";
-			gpios = <&gpio 35 0>;
-			default-state = "keep";
-			linux,default-trigger = "default-on";
-		};
-	};
 };
 
 &gpio {
-	pinctrl-0 = <&gpioout &alt0 &i2s_alt0 &alt3>;
+	spi0_pins: spi0_pins {
+		brcm,pins = <7 8 9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
 
-	/* I2S interface */
-	i2s_alt0: i2s_alt0 {
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
 		brcm,pins = <18 19 20 21>;
-		brcm,function = <BCM2835_FSEL_ALT0>;
+		brcm,function = <4>; /* alt0 */
+	};
+};
+
+&mmc {
+	status = "okay";
+	bus-width = <4>;
+};
+
+&fb {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins>;
+
+	spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <500000>;
+	};
+
+	spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <500000>;
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	#sound-dai-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&gpio 47 0>;
+	};
+
+	pwr_led: pwr {
+		label = "led1";
+		linux,default-trigger = "input";
+		gpios = <&gpio 35 0>;
+	};
+};
+
+/ {
+	__overrides__ {
+		uart0 = <&uart0>,"status";
+		uart0_clkrate = <&clk_uart0>,"clock-frequency:0";
+		uart1_clkrate = <&uart1>,"clock-frequency:0";
+		i2s = <&i2s>,"status";
+		spi = <&spi0>,"status";
+		i2c0 = <&i2c0>,"status";
+		i2c1 = <&i2c1>,"status";
+		i2c2_iknowwhatimdoing = <&i2c2>,"status";
+		i2c0_baudrate = <&i2c0>,"clock-frequency:0";
+		i2c1_baudrate = <&i2c1>,"clock-frequency:0";
+		i2c2_baudrate = <&i2c2>,"clock-frequency:0";
+		core_freq = <&clk_core>,"clock-frequency:0";
+
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+
+		pwr_led_gpio = <&pwr_led>,"gpios:4";
+		pwr_led_activelow = <&pwr_led>,"gpios:8";
+		pwr_led_trigger = <&pwr_led>,"linux,default-trigger";
+
+		audio = <&audio>,"status";
+		watchdog = <&watchdog>,"status";
+		random = <&random>,"status";
 	};
 };

arch/arm/boot/dts/bcm2835-rpi-b.dts

@@ -1,17 +1,118 @@
 /dts-v1/;
-#include "bcm2835-rpi.dtsi"
+#include "bcm2835.dtsi"
 
 / {
 	compatible = "raspberrypi,model-b", "brcm,bcm2835";
 	model = "Raspberry Pi Model B";
-
-	leds {
-		act {
-			gpios = <&gpio 16 1>;
-		};
-	};
 };
 
 &gpio {
-	pinctrl-0 = <&gpioout &alt0 &alt3>;
+	spi0_pins: spi0_pins {
+		brcm,pins = <7 8 9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <28 29 30 31>;
+		brcm,function = <6>; /* alt2 */
+	};
+};
+
+&mmc {
+	status = "okay";
+	bus-width = <4>;
+};
+
+&fb {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins>;
+
+	spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <500000>;
+	};
+
+	spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <500000>;
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	#sound-dai-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&gpio 16 1>;
+	};
+};
+
+/ {
+	__overrides__ {
+		uart0 = <&uart0>,"status";
+		uart0_clkrate = <&clk_uart0>,"clock-frequency:0";
+		uart1_clkrate = <&uart1>,"clock-frequency:0";
+		i2s = <&i2s>,"status";
+		spi = <&spi0>,"status";
+		i2c0 = <&i2c0>,"status";
+		i2c1 = <&i2c1>,"status";
+		i2c2_iknowwhatimdoing = <&i2c2>,"status";
+		i2c0_baudrate = <&i2c0>,"clock-frequency:0";
+		i2c1_baudrate = <&i2c1>,"clock-frequency:0";
+		i2c2_baudrate = <&i2c2>,"clock-frequency:0";
+		core_freq = <&clk_core>,"clock-frequency:0";
+
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+
+		audio = <&audio>,"status";
+		watchdog = <&watchdog>,"status";
+		random = <&random>,"status";
+	};
 };

arch/arm/boot/dts/bcm2835-rpi-cm.dts

@@ -0,0 +1,93 @@
+/dts-v1/;
+
+#include "bcm2835-rpi-cm.dtsi"
+
+/ {
+	model = "Raspberry Pi Compute Module";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&gpio {
+	spi0_pins: spi0_pins {
+		brcm,pins = <7 8 9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <4>; /* alt0 */
+	};
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins>;
+
+	spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <500000>;
+	};
+
+	spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <500000>;
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	#sound-dai-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+/ {
+	__overrides__ {
+		uart0 = <&uart0>,"status";
+		uart0_clkrate = <&clk_uart0>,"clock-frequency:0";
+		uart1_clkrate = <&uart1>,"clock-frequency:0";
+		i2s = <&i2s>,"status";
+		spi = <&spi0>,"status";
+		i2c0 = <&i2c0>,"status";
+		i2c1 = <&i2c1>,"status";
+		i2c2_iknowwhatimdoing = <&i2c2>,"status";
+		i2c0_baudrate = <&i2c0>,"clock-frequency:0";
+		i2c1_baudrate = <&i2c1>,"clock-frequency:0";
+		i2c2_baudrate = <&i2c2>,"clock-frequency:0";
+		core_freq = <&clk_core>,"clock-frequency:0";
+	};
+};

arch/arm/boot/dts/bcm2835-rpi-cm.dtsi

@@ -0,0 +1,30 @@
+#include "bcm2835.dtsi"
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&gpio 47 0>;
+	};
+};
+
+&mmc {
+	status = "okay";
+	bus-width = <4>;
+};
+
+&fb {
+	status = "okay";
+};
+
+/ {
+	__overrides__ {
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+
+		audio = <&audio>,"status";
+		watchdog = <&watchdog>,"status";
+		random = <&random>,"status";
+	};
+};

arch/arm/boot/dts/bcm2835.dtsi

@@ -1,206 +1,39 @@
-#include <dt-bindings/pinctrl/bcm2835.h>
-#include <dt-bindings/clock/bcm2835.h>
-#include "skeleton.dtsi"
+#include "bcm2708_common.dtsi"
 
 / {
 	compatible = "brcm,bcm2835";
 	model = "BCM2835";
-	interrupt-parent = <&intc>;
 
 	chosen {
-		bootargs = "earlyprintk console=ttyAMA0";
+		bootargs = "";
 	};
 
 	soc {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges = <0x7e000000 0x20000000 0x02000000>;
+		ranges = <0x7e000000 0x20000000 0x01000000>;
 		dma-ranges = <0x40000000 0x00000000 0x20000000>;
 
 		timer@7e003000 {
 			compatible = "brcm,bcm2835-system-timer";
 			reg = <0x7e003000 0x1000>;
 			interrupts = <1 0>, <1 1>, <1 2>, <1 3>;
-			/* This could be a reference to BCM2835_CLOCK_TIMER,
-			 * but we don't have the driver using the common clock
-			 * support yet.
-			 */
 			clock-frequency = <1000000>;
 		};
 
-		dma: dma@7e007000 {
-			compatible = "brcm,bcm2835-dma";
-			reg = <0x7e007000 0xf00>;
-			interrupts = <1 16>,
-				     <1 17>,
-				     <1 18>,
-				     <1 19>,
-				     <1 20>,
-				     <1 21>,
-				     <1 22>,
-				     <1 23>,
-				     <1 24>,
-				     <1 25>,
-				     <1 26>,
-				     <1 27>,
-				     <1 28>;
-
-			#dma-cells = <1>;
-			brcm,dma-channel-mask = <0x7f35>;
-		};
-
-		intc: interrupt-controller@7e00b200 {
-			compatible = "brcm,bcm2835-armctrl-ic";
-			reg = <0x7e00b200 0x200>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-		};
-
-		watchdog@7e100000 {
-			compatible = "brcm,bcm2835-pm-wdt";
-			reg = <0x7e100000 0x28>;
-		};
-
-		clocks: cprman@7e101000 {
-			compatible = "brcm,bcm2835-cprman";
-			#clock-cells = <1>;
-			reg = <0x7e101000 0x2000>;
-
-			/* CPRMAN derives everything from the platform's
-			 * oscillator.
-			 */
-			clocks = <&clk_osc>;
-		};
-
-		rng@7e104000 {
-			compatible = "brcm,bcm2835-rng";
-			reg = <0x7e104000 0x10>;
-		};
-
-		mailbox: mailbox@7e00b800 {
-			compatible = "brcm,bcm2835-mbox";
-			reg = <0x7e00b880 0x40>;
-			interrupts = <0 1>;
-			#mbox-cells = <0>;
-		};
-
-		gpio: gpio@7e200000 {
-			compatible = "brcm,bcm2835-gpio";
-			reg = <0x7e200000 0xb4>;
-			/*
-			 * The GPIO IP block is designed for 3 banks of GPIOs.
-			 * Each bank has a GPIO interrupt for itself.
-			 * There is an overall "any bank" interrupt.
-			 * In order, these are GIC interrupts 17, 18, 19, 20.
-			 * Since the BCM2835 only has 2 banks, the 2nd bank
-			 * interrupt output appears to be mirrored onto the
-			 * 3rd bank's interrupt signal.
-			 * So, a bank0 interrupt shows up on 17, 20, and
-			 * a bank1 interrupt shows up on 18, 19, 20!
-			 */
-			interrupts = <2 17>, <2 18>, <2 19>, <2 20>;
-
-			gpio-controller;
-			#gpio-cells = <2>;
-
-			interrupt-controller;
-			#interrupt-cells = <2>;
-		};
-
-		uart0: uart@7e201000 {
-			compatible = "brcm,bcm2835-pl011", "arm,pl011", "arm,primecell";
-			reg = <0x7e201000 0x1000>;
-			interrupts = <2 25>;
-			clocks = <&clocks BCM2835_CLOCK_UART>,
-				 <&clocks BCM2835_CLOCK_VPU>;
-			clock-names = "uartclk", "apb_pclk";
-			arm,primecell-periphid = <0x00241011>;
-		};
-
-		i2s: i2s@7e203000 {
-			compatible = "brcm,bcm2835-i2s";
-			reg = <0x7e203000 0x20>,
-			      <0x7e101098 0x02>;
-
-			dmas = <&dma 2>,
-			       <&dma 3>;
-			dma-names = "tx", "rx";
-			status = "disabled";
-		};
-
-		spi: spi@7e204000 {
-			compatible = "brcm,bcm2835-spi";
-			reg = <0x7e204000 0x1000>;
-			interrupts = <2 22>;
-			clocks = <&clocks BCM2835_CLOCK_VPU>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			status = "disabled";
-		};
-
-		i2c0: i2c@7e205000 {
-			compatible = "brcm,bcm2835-i2c";
-			reg = <0x7e205000 0x1000>;
-			interrupts = <2 21>;
-			clocks = <&clocks BCM2835_CLOCK_VPU>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			status = "disabled";
-		};
-
-		sdhci: sdhci@7e300000 {
-			compatible = "brcm,bcm2835-sdhci";
-			reg = <0x7e300000 0x100>;
-			interrupts = <2 30>;
-			clocks = <&clocks BCM2835_CLOCK_EMMC>;
-			status = "disabled";
-		};
-
-		i2c1: i2c@7e804000 {
-			compatible = "brcm,bcm2835-i2c";
-			reg = <0x7e804000 0x1000>;
-			interrupts = <2 21>;
-			clocks = <&clocks BCM2835_CLOCK_VPU>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			status = "disabled";
-		};
-
-		i2c2: i2c@7e805000 {
-			compatible = "brcm,bcm2835-i2c";
-			reg = <0x7e805000 0x1000>;
-			interrupts = <2 21>;
-			clocks = <&clocks BCM2835_CLOCK_VPU>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			status = "disabled";
-		};
-
-		usb@7e980000 {
-			compatible = "brcm,bcm2835-usb";
-			reg = <0x7e980000 0x10000>;
-			interrupts = <1 9>;
-		};
-
 		arm-pmu {
 			compatible = "arm,arm1176-pmu";
 		};
-	};
 
-	clocks {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		/* The oscillator is the root of the clock tree. */
-		clk_osc: clock@3 {
-			compatible = "fixed-clock";
-			reg = <3>;
-			#clock-cells = <0>;
-			clock-output-names = "osc";
-			clock-frequency = <19200000>;
+		aux_enable: aux_enable@0x7e215004 {
+			compatible = "bcrm,bcm2835-aux-enable";
+			reg = <0x7e215004 0x04>;
 		};
-
 	};
 };
+
+&intc {
+	compatible = "brcm,bcm2835-armctrl-ic";
+};
+
+&watchdog {
+	status = "okay";
+};

arch/arm/boot/dts/exynos4210-trats.dts

@@ -298,6 +298,8 @@
 		compatible = "maxim,max8997-pmic";
 
 		reg = <0x66>;
+		interrupt-parent = <&gpx0>;
+		interrupts = <7 0>;
 
 		max8997,pmic-buck1-uses-gpio-dvs;
 		max8997,pmic-buck2-uses-gpio-dvs;

arch/arm/boot/dts/overlays/Makefile

@@ -0,0 +1,102 @@
+ifeq ($(CONFIG_OF),y)
+
+# Overlays for the Raspberry Pi platform
+
+ifeq ($(CONFIG_ARCH_BCM2708),y)
+   RPI_DT_OVERLAYS=y
+endif
+ifeq ($(CONFIG_ARCH_BCM2709),y)
+   RPI_DT_OVERLAYS=y
+endif
+ifeq ($(CONFIG_ARCH_BCM2835),y)
+   RPI_DT_OVERLAYS=y
+endif
+
+dtbo-$(RPI_DT_OVERLAYS) += adau1977-adc.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += ads1015.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += ads7846.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += akkordion-iqdacplus.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += at86rf233.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += audioinjector-wm8731-audio.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += bmp085_i2c-sensor.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += dht11.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += dpi24.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += dwc-otg.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += dwc2.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += enc28j60.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += gpio-ir.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += gpio-poweroff.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += hifiberry-amp.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += hifiberry-dac.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += hifiberry-dacplus.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += hifiberry-digi.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += hy28a.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += hy28b.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += i2c-gpio.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += i2c-mux.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += i2c-pwm-pca9685a.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += i2c-rtc.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += i2c0-bcm2708.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += i2c1-bcm2708.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += i2s-gpio28-31.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += i2s-mmap.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += iqaudio-dac.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += iqaudio-dacplus.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += justboom-dac.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += justboom-digi.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += lirc-rpi.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += mcp23017.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += mcp2515-can0.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += mcp2515-can1.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += mmc.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += mz61581.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += pi3-act-led.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += pi3-disable-bt.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += pi3-miniuart-bt.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += piscreen.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += piscreen2r.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += pitft22.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += pitft28-capacitive.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += pitft28-resistive.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += pps-gpio.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += pwm.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += pwm-2chan.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += qca7000.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += raspidac3.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += rpi-backlight.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += rpi-dac.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += rpi-display.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += rpi-ft5406.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += rpi-proto.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += rpi-sense.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += rra-digidac1-wm8741-audio.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += sdhost.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += sdio.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += sdio-1bit.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += sdtweak.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += smi.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += smi-dev.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += smi-nand.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += spi-gpio35-39.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += spi-rtc.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += spi1-1cs.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += spi1-2cs.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += spi1-3cs.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += spi2-1cs.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += spi2-2cs.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += spi2-3cs.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += tinylcd35.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += uart1.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += vc4-kms-v3d.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += vga666.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += w1-gpio.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += w1-gpio-pullup.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += wittypi.dtbo
+
+targets += dtbs dtbs_install
+targets += $(dtbo-y)
+
+endif
+
+always		:= $(dtbo-y)
+clean-files	:= *.dtbo

arch/arm/boot/dts/overlays/adau1977-adc-overlay.dts

@@ -0,0 +1,53 @@
+// Definitions for ADAU1977 ADC
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+    
+	fragment@0 {
+		target = <&soc>;
+		
+		__overlay__ {
+			codec_supply: fixedregulator@0 {
+				compatible = "regulator-fixed";
+				regulator-name = "AVDD";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+		};
+	};
+	
+	fragment@1 {
+        	target = <&i2c>;
+        	
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+			
+			adau1977: codec@11 {
+                        	compatible = "adi,adau1977";
+                        	reg = <0x11>;
+                        	reset-gpios = <&gpio 5 0>;
+                        	AVDD-supply = <&codec_supply>;
+                	};
+        	};
+	};
+
+	fragment@2 {
+		target = <&i2s>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@3 {
+		target = <&sound>;
+		__overlay__ {
+			compatible = "adi,adau1977-adc";
+			i2s-controller = <&i2s>;
+			status = "okay";
+		};
+	};
+};

arch/arm/boot/dts/overlays/ads1015-overlay.dts

@@ -0,0 +1,98 @@
+/*
+ * 2016 - Erik Sejr
+ */
+/dts-v1/;
+/plugin/;
+
+/ {
+    compatible = "brcm,bcm2708";
+    /* ----------- ADS1015 ------------ */
+    fragment@0 {
+        target = <&i2c_arm>;
+        __overlay__ {
+            #address-cells = <1>;
+            #size-cells = <0>;
+            status = "okay";
+            ads1015: ads1015 {
+                compatible = "ti,ads1015";
+                status = "okay";
+                #address-cells = <1>;
+                #size-cells = <0>;
+                reg = <0x48>;
+            };
+        };
+    };
+
+    fragment@1 {
+        target-path = "i2c_arm/ads1015";
+        __overlay__ {
+            #address-cells = <1>;
+            #size-cells = <0>;
+            channel_a: channel_a {
+                reg = <4>;
+                ti,gain = <2>;
+                ti,datarate = <4>;
+            };
+        };
+    };
+
+    fragment@2 {
+        target-path = "i2c_arm/ads1015";
+        __dormant__ {
+            #address-cells = <1>;
+            #size-cells = <0>;
+            channel_b: channel_b {
+                reg = <5>;
+                ti,gain = <2>;
+                ti,datarate = <4>;
+            };
+        };
+    };
+
+    fragment@3 {
+        target-path = "i2c_arm/ads1015";
+        __dormant__ {
+            #address-cells = <1>;
+            #size-cells = <0>;
+            channel_c: channel_c {
+                reg = <6>;
+                ti,gain = <2>;
+                ti,datarate = <4>;
+            };
+        };
+    };
+
+    fragment@4 {
+        target-path = "i2c_arm/ads1015";
+        __dormant__ {
+            #address-cells = <1>;
+            #size-cells = <0>;
+            channel_d: channel_d {
+                reg = <7>;
+                ti,gain = <2>;
+                ti,datarate = <4>;
+            };
+        };
+    };
+
+    __overrides__ {
+        addr =            <&ads1015>,"reg:0";
+        cha_enable =      <0>,"=1";
+        cha_cfg =         <&channel_a>,"reg:0";
+        cha_gain =        <&channel_a>,"ti,gain:0";
+        cha_datarate =    <&channel_a>,"ti,datarate:0";
+        chb_enable =      <0>,"=2";
+        chb_cfg =         <&channel_b>,"reg:0";
+        chb_gain =        <&channel_b>,"ti,gain:0";
+        chb_datarate =    <&channel_b>,"ti,datarate:0";
+        chc_enable =      <0>,"=3";
+        chc_cfg =         <&channel_c>,"reg:0";
+        chc_gain =        <&channel_c>,"ti,gain:0";
+        chc_datarate =    <&channel_c>,"ti,datarate:0";
+        chd_enable =      <0>,"=4";
+        chd_cfg =         <&channel_d>,"reg:0";
+        chd_gain =        <&channel_d>,"ti,gain:0";
+        chd_datarate =    <&channel_d>,"ti,datarate:0";
+   };
+
+};

arch/arm/boot/dts/overlays/ads7846-overlay.dts

@@ -0,0 +1,89 @@
+/*
+ * Generic Device Tree overlay for the ADS7846 touch controller
+ *
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
+
+	fragment@0 {
+		target = <&spi0>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&spidev0>;
+		__overlay__ {
+			status = "disabled";
+		};
+	};
+
+	fragment@2 {
+		target = <&spidev1>;
+		__overlay__ {
+			status = "disabled";
+		};
+	};
+
+	fragment@3 {
+		target = <&gpio>;
+		__overlay__ {
+			ads7846_pins: ads7846_pins {
+				brcm,pins = <255>; /* illegal default value */
+				brcm,function = <0>; /* in */
+				brcm,pull = <0>; /* none */
+			};
+		};
+	};
+
+	fragment@4 {
+		target = <&spi0>;
+		__overlay__ {
+			/* needed to avoid dtc warning */
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			ads7846: ads7846@1 {
+				compatible = "ti,ads7846";
+				reg = <1>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&ads7846_pins>;
+
+				spi-max-frequency = <2000000>;
+				interrupts = <255 2>; /* high-to-low edge triggered */
+				interrupt-parent = <&gpio>;
+				pendown-gpio = <&gpio 255 0>;
+
+				/* driver defaults */
+				ti,x-min = /bits/ 16 <0>;
+				ti,y-min = /bits/ 16 <0>;
+				ti,x-max = /bits/ 16 <0x0FFF>;
+				ti,y-max = /bits/ 16 <0x0FFF>;
+				ti,pressure-min = /bits/ 16 <0>;
+				ti,pressure-max = /bits/ 16 <0xFFFF>;
+				ti,x-plate-ohms = /bits/ 16 <400>;
+			};
+		};
+	};
+	__overrides__ {
+		cs =     <&ads7846>,"reg:0";
+		speed =  <&ads7846>,"spi-max-frequency:0";
+		penirq = <&ads7846_pins>,"brcm,pins:0", /* REQUIRED */
+			 <&ads7846>,"interrupts:0",
+			 <&ads7846>,"pendown-gpio:4";
+		penirq_pull = <&ads7846_pins>,"brcm,pull:0";
+		swapxy = <&ads7846>,"ti,swap-xy?";
+		xmin =   <&ads7846>,"ti,x-min;0";
+		ymin =   <&ads7846>,"ti,y-min;0";
+		xmax =   <&ads7846>,"ti,x-max;0";
+		ymax =   <&ads7846>,"ti,y-max;0";
+		pmin =   <&ads7846>,"ti,pressure-min;0";
+		pmax =   <&ads7846>,"ti,pressure-max;0";
+		xohms =  <&ads7846>,"ti,x-plate-ohms;0";
+	};
+};

arch/arm/boot/dts/overlays/akkordion-iqdacplus-overlay.dts

@@ -0,0 +1,46 @@
+// Definitions for Digital Dreamtime Akkordion using IQaudIO DAC+ or DACZero
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&i2s>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&i2c1>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			pcm5122@4c {
+				#sound-dai-cells = <0>;
+				compatible = "ti,pcm5122";
+				reg = <0x4c>;
+				status = "okay";
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&sound>;
+		frag2: __overlay__ {
+			compatible = "iqaudio,iqaudio-dac";
+			card_name = "Akkordion";
+			dai_name = "IQaudIO DAC";
+			dai_stream_name = "IQaudIO DAC HiFi";
+			i2s-controller = <&i2s>;
+			status = "okay";
+		};
+	};
+
+	__overrides__ {
+		24db_digital_gain = <&frag2>,"iqaudio,24db_digital_gain?";
+	};
+};

arch/arm/boot/dts/overlays/at86rf233-overlay.dts

@@ -0,0 +1,57 @@
+/dts-v1/;
+/plugin/;
+
+/* Overlay for Atmel AT86RF233 IEEE 802.15.4 WPAN transceiver on spi0.0 */
+
+/ {
+	compatible = "brcm,bcm2835", "brcm,bcm2836", "brcm,bcm2708", "brcm,bcm2709";
+
+	fragment@0 {
+		target = <&spi0>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "okay";
+
+			lowpan0: at86rf233@0 {
+				compatible = "atmel,at86rf233";
+				reg = <0>;
+				interrupt-parent = <&gpio>;
+				interrupts = <23 4>; /* active high */
+				reset-gpio = <&gpio 24 1>;
+				sleep-gpio = <&gpio 25 1>;
+				spi-max-frequency = <3000000>;
+				xtal-trim = /bits/ 8 <0xf>;
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&spidev0>;
+		__overlay__ {
+			status = "disabled";
+		};
+	};
+
+	fragment@2 {
+		target = <&gpio>;
+		__overlay__ {
+			lowpan0_pins: lowpan0_pins {
+				brcm,pins = <23 24 25>;
+				brcm,function = <0 1 1>; /* in out out */
+			};
+		};
+	};
+
+	__overrides__ {
+		interrupt = <&lowpan0>, "interrupts:0",
+			<&lowpan0_pins>, "brcm,pins:0";
+		reset     = <&lowpan0>, "reset-gpio:4",
+			<&lowpan0_pins>, "brcm,pins:4";
+		sleep     = <&lowpan0>, "sleep-gpio:4",
+			<&lowpan0_pins>, "brcm,pins:8";
+		speed     = <&lowpan0>, "spi-max-frequency:0";
+		trim      = <&lowpan0>, "xtal-trim.0";
+	};
+};

arch/arm/boot/dts/overlays/audioinjector-wm8731-audio-overlay.dts

@@ -0,0 +1,39 @@
+// Definitions for audioinjector.net audio add on soundcard
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&i2s>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&i2c1>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			wm8731@1a {
+				#sound-dai-cells = <0>;
+				compatible = "wlf,wm8731";
+				reg = <0x1a>;
+				status = "okay";
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&sound>;
+		__overlay__ {
+			compatible = "ai,audioinjector-pi-soundcard";
+			i2s-controller = <&i2s>;
+			status = "okay";
+		};
+	};
+};

arch/arm/boot/dts/overlays/bmp085_i2c-sensor-overlay.dts

@@ -0,0 +1,23 @@
+// Definitions for BMP085/BMP180 digital barometric pressure and temperature sensors from Bosch Sensortec
+/dts-v1/;
+/plugin/;
+
+/ {
+        compatible = "brcm,bcm2708";
+
+        fragment@0 {
+                target = <&i2c_arm>;
+                __overlay__ {
+                        #address-cells = <1>;
+                        #size-cells = <0>;
+                        status = "okay";
+
+                        bmp085@77 {
+                                compatible = "bosch,bmp085";
+                                reg = <0x77>;
+                                default-oversampling = <3>;
+                                status = "okay";
+                        };
+                };
+        };
+};

arch/arm/boot/dts/overlays/dht11-overlay.dts

@@ -0,0 +1,39 @@
+/*
+ * Overlay for the DHT11/21/22 humidity/temperature sensor modules.
+ */
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target-path = "/";
+		__overlay__ {
+
+			dht11: dht11@0 {
+				compatible = "dht11";
+				pinctrl-names = "default";
+				pinctrl-0 = <&dht11_pins>;
+				gpios = <&gpio 4 0>;
+				status = "okay";
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&gpio>;
+		__overlay__ {
+			dht11_pins: dht11_pins {
+				brcm,pins = <4>;
+				brcm,function = <0>; // in
+				brcm,pull = <0>; // off
+			};
+		};
+	};
+
+	__overrides__ {
+		gpiopin = <&dht11_pins>,"brcm,pins:0",
+			<&dht11>,"gpios:4";
+	};
+};

arch/arm/boot/dts/overlays/dpi24-overlay.dts

@@ -0,0 +1,31 @@
+/dts-v1/;
+/plugin/;
+
+/{
+	compatible = "brcm,bcm2708";
+
+	// There is no DPI driver module, but we need a platform device
+	// node (that doesn't already use pinctrl) to hang the pinctrl
+	// reference on - leds will do
+
+	fragment@0 {
+		target = <&leds>;
+		__overlay__ {
+			pinctrl-names = "default";
+			pinctrl-0 = <&dpi24_pins>;
+		};
+	};
+
+	fragment@1 {
+		target = <&gpio>;
+		__overlay__ {
+			dpi24_pins: dpi24_pins {
+				brcm,pins = <0 1 2 3 4 5 6 7 8 9 10 11
+					     12 13 14 15 16 17 18 19 20
+					     21 22 23 24 25 26 27>;
+				brcm,function = <6>; /* alt2 */
+				brcm,pull = <0>; /* no pull */
+			};
+		};
+	};
+};

arch/arm/boot/dts/overlays/dwc-otg-overlay.dts

@@ -0,0 +1,20 @@
+/dts-v1/;
+/plugin/;
+
+/{
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&usb>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		__overlay__ {
+			compatible = "brcm,bcm2708-usb";
+			reg = <0x7e980000 0x10000>,
+			      <0x7e006000 0x1000>;
+			interrupts = <2 0>,
+				     <1 9>;
+			status = "okay";
+		};
+	};
+};

arch/arm/boot/dts/overlays/dwc2-overlay.dts

@@ -0,0 +1,29 @@
+/dts-v1/;
+/plugin/;
+
+/{
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&usb>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		dwc2_usb: __overlay__ {
+			compatible = "brcm,bcm2835-usb";
+			reg = <0x7e980000 0x10000>;
+			interrupts = <1 9>;
+			dr_mode = "otg";
+			g-np-tx-fifo-size = <32>;
+			g-rx-fifo-size = <256>;
+			g-tx-fifo-size = <256 128 128 64 64 64 32>;
+			status = "okay";
+		};
+	};
+
+	__overrides__ {
+		dr_mode = <&dwc2_usb>, "dr_mode";
+		g-np-tx-fifo-size = <&dwc2_usb>,"g-np-tx-fifo-size:0";
+		g-rx-fifo-size = <&dwc2_usb>,"g-rx-fifo-size:0";
+		g-tx-fifo-size = <&dwc2_usb>,"g-tx-fifo-size:0";
+	};
+};

arch/arm/boot/dts/overlays/enc28j60-overlay.dts

@@ -0,0 +1,53 @@
+// Overlay for the Microchip ENC28J60 Ethernet Controller
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&spi0>;
+		__overlay__ {
+			/* needed to avoid dtc warning */
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "okay";
+
+			eth1: enc28j60@0{
+				compatible = "microchip,enc28j60";
+				reg = <0>; /* CE0 */
+				pinctrl-names = "default";
+				pinctrl-0 = <&eth1_pins>;
+				interrupt-parent = <&gpio>;
+				interrupts = <25 0x2>; /* falling edge */
+				spi-max-frequency = <12000000>;
+				status = "okay";
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&spidev0>;
+		__overlay__ {
+			status = "disabled";
+		};
+	};
+
+	fragment@2 {
+		target = <&gpio>;
+		__overlay__ {
+			eth1_pins: eth1_pins {
+				brcm,pins = <25>;
+				brcm,function = <0>; /* in */
+				brcm,pull = <0>; /* none */
+			};
+		};
+	};
+
+	__overrides__ {
+		int_pin = <&eth1>, "interrupts:0",
+		          <&eth1_pins>, "brcm,pins:0";
+		speed   = <&eth1>, "spi-max-frequency:0";
+	};
+};

arch/arm/boot/dts/overlays/gpio-ir-overlay.dts

@@ -0,0 +1,44 @@
+// Definitions for ir-gpio module
+/dts-v1/;
+/plugin/;
+
+/ {
+        compatible = "brcm,bcm2708";
+
+        fragment@0 {
+                target-path = "/";
+                __overlay__ {
+                        gpio_ir: ir-receiver {
+                                compatible = "gpio-ir-receiver";
+
+                                // pin number, high or low
+                                gpios = <&gpio 18 1>;
+
+                                // parameter for keymap name
+                                linux,rc-map-name = "rc-rc6-mce";
+
+                                status = "okay";
+                        };
+                };
+        };
+
+        fragment@1 {
+                target = <&gpio>;
+                __overlay__ {
+                        gpio_ir_pins: gpio_ir_pins {
+                                brcm,pins = <18>;                       // pin 18
+                                brcm,function = <0>;                    // in
+                                brcm,pull = <1>;                        // down
+                        };
+                };
+        };
+
+        __overrides__ {
+                // parameters
+                gpio_pin =      <&gpio_ir>,"gpios:4",
+                                        <&gpio_ir_pins>,"brcm,pins:0";  // pin number
+                gpio_pull = <&gpio_ir_pins>,"brcm,pull:0";              // pull-up/down state
+
+                rc-map-name = <&gpio_ir>,"linux,rc-map-name";           // default rc map
+        };
+};

arch/arm/boot/dts/overlays/gpio-poweroff-overlay.dts

@@ -0,0 +1,34 @@
+// Definitions for gpio-poweroff module
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target-path = "/";
+		__overlay__ {
+			power_ctrl: power_ctrl {
+				compatible = "gpio-poweroff";
+				gpios = <&gpio 26 0>;
+				force;
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&gpio>;
+		__overlay__ {
+			power_ctrl_pins: power_ctrl_pins {
+				brcm,pins = <26>;
+				brcm,function = <1>; // out
+			};
+		};
+	};
+
+	__overrides__ {
+		gpiopin =       <&power_ctrl>,"gpios:4",
+				<&power_ctrl_pins>,"brcm,pins:0";
+		active_low =    <&power_ctrl>,"gpios:8";
+	};
+};

arch/arm/boot/dts/overlays/hifiberry-amp-overlay.dts

@@ -0,0 +1,39 @@
+// Definitions for HiFiBerry Amp/Amp+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&i2s>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&i2c1>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			tas5713@1b {
+				#sound-dai-cells = <0>;
+				compatible = "ti,tas5713";
+				reg = <0x1b>;
+				status = "okay";
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&sound>;
+		__overlay__ {
+			compatible = "hifiberry,hifiberry-amp";
+			i2s-controller = <&i2s>;
+			status = "okay";
+		};
+	};
+};

arch/arm/boot/dts/overlays/hifiberry-dac-overlay.dts

@@ -0,0 +1,34 @@
+// Definitions for HiFiBerry DAC
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&i2s>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target-path = "/";
+		__overlay__ {
+			pcm5102a-codec {
+				#sound-dai-cells = <0>;
+				compatible = "ti,pcm5102a";
+				status = "okay";
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&sound>;
+		__overlay__ {
+			compatible = "hifiberry,hifiberry-dac";
+			i2s-controller = <&i2s>;
+			status = "okay";
+		};
+	};
+};

arch/arm/boot/dts/overlays/hifiberry-dacplus-overlay.dts

@@ -0,0 +1,56 @@
+// Definitions for HiFiBerry DAC+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target-path = "/clocks";
+		__overlay__ {
+			dacpro_osc: dacpro_osc {
+				compatible = "hifiberry,dacpro-clk";
+				#clock-cells = <0>;
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&i2s>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@2 {
+		target = <&i2c1>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			pcm5122@4d {
+				#sound-dai-cells = <0>;
+				compatible = "ti,pcm5122";
+				reg = <0x4d>;
+				clocks = <&dacpro_osc>;
+				status = "okay";
+			};
+		};
+	};
+
+	fragment@3 {
+		target = <&sound>;
+		hifiberry_dacplus: __overlay__ {
+			compatible = "hifiberry,hifiberry-dacplus";
+			i2s-controller = <&i2s>;
+			status = "okay";
+		};
+	};
+
+	__overrides__ {
+		24db_digital_gain =
+			<&hifiberry_dacplus>,"hifiberry,24db_digital_gain?";
+		slave = <&hifiberry_dacplus>,"hifiberry-dacplus,slave?";
+	};
+};

arch/arm/boot/dts/overlays/hifiberry-digi-overlay.dts

@@ -0,0 +1,39 @@
+// Definitions for HiFiBerry Digi
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&i2s>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&i2c1>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			wm8804@3b {
+				#sound-dai-cells = <0>;
+				compatible = "wlf,wm8804";
+				reg = <0x3b>;
+				status = "okay";
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&sound>;
+		__overlay__ {
+			compatible = "hifiberry,hifiberry-digi";
+			i2s-controller = <&i2s>;
+			status = "okay";
+		};
+	};
+};

arch/arm/boot/dts/overlays/hy28a-overlay.dts

@@ -0,0 +1,93 @@
+/*
+ * Device Tree overlay for HY28A display
+ *
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
+
+	fragment@0 {
+		target = <&spi0>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&spidev0>;
+		__overlay__ {
+			status = "disabled";
+		};
+	};
+
+	fragment@2 {
+		target = <&spidev1>;
+		__overlay__ {
+			status = "disabled";
+		};
+	};
+
+	fragment@3 {
+		target = <&gpio>;
+		__overlay__ {
+			hy28a_pins: hy28a_pins {
+				brcm,pins = <17 25 18>;
+				brcm,function = <0 1 1>; /* in out out */
+			};
+		};
+	};
+
+	fragment@4 {
+		target = <&spi0>;
+		__overlay__ {
+			/* needed to avoid dtc warning */
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			hy28a: hy28a@0{
+				compatible = "ilitek,ili9320";
+				reg = <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&hy28a_pins>;
+
+				spi-max-frequency = <32000000>;
+				spi-cpol;
+				spi-cpha;
+				rotate = <270>;
+				bgr;
+				fps = <50>;
+				buswidth = <8>;
+				startbyte = <0x70>;
+				reset-gpios = <&gpio 25 0>;
+				led-gpios = <&gpio 18 1>;
+				debug = <0>;
+			};
+
+			hy28a_ts: hy28a-ts@1 {
+				compatible = "ti,ads7846";
+				reg = <1>;
+
+				spi-max-frequency = <2000000>;
+				interrupts = <17 2>; /* high-to-low edge triggered */
+				interrupt-parent = <&gpio>;
+				pendown-gpio = <&gpio 17 0>;
+				ti,x-plate-ohms = /bits/ 16 <100>;
+				ti,pressure-max = /bits/ 16 <255>;
+			};
+		};
+	};
+	__overrides__ {
+		speed =		<&hy28a>,"spi-max-frequency:0";
+		rotate =	<&hy28a>,"rotate:0";
+		fps =		<&hy28a>,"fps:0";
+		debug =		<&hy28a>,"debug:0";
+		xohms =		<&hy28a_ts>,"ti,x-plate-ohms;0";
+		resetgpio =	<&hy28a>,"reset-gpios:4",
+				<&hy28a_pins>, "brcm,pins:1";
+		ledgpio =	<&hy28a>,"led-gpios:4",
+				<&hy28a_pins>, "brcm,pins:2";
+	};
+};

arch/arm/boot/dts/overlays/hy28b-overlay.dts

@@ -0,0 +1,148 @@
+/*
+ * Device Tree overlay for HY28b display shield by Texy
+ *
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
+
+	fragment@0 {
+		target = <&spi0>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&spidev0>;
+		__overlay__ {
+			status = "disabled";
+		};
+	};
+
+	fragment@2 {
+		target = <&spidev1>;
+		__overlay__ {
+			status = "disabled";
+		};
+	};
+
+	fragment@3 {
+		target = <&gpio>;
+		__overlay__ {
+			hy28b_pins: hy28b_pins {
+				brcm,pins = <17 25 18>;
+				brcm,function = <0 1 1>; /* in out out */
+			};
+		};
+	};
+
+	fragment@4 {
+		target = <&spi0>;
+		__overlay__ {
+			/* needed to avoid dtc warning */
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			hy28b: hy28b@0{
+				compatible = "ilitek,ili9325";
+				reg = <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&hy28b_pins>;
+
+				spi-max-frequency = <48000000>;
+				spi-cpol;
+				spi-cpha;
+				rotate = <270>;
+				bgr;
+				fps = <50>;
+				buswidth = <8>;
+				startbyte = <0x70>;
+				reset-gpios = <&gpio 25 0>;
+				led-gpios = <&gpio 18 1>;
+
+				gamma = "04 1F 4 7 7 0 7 7 6 0\n0F 00 1 7 4 0 0 0 6 7";
+
+				init = <0x10000e7 0x0010
+					0x1000000 0x0001
+					0x1000001 0x0100
+					0x1000002 0x0700
+				        0x1000003 0x1030
+					0x1000004 0x0000
+					0x1000008 0x0207
+					0x1000009 0x0000
+				        0x100000a 0x0000
+					0x100000c 0x0001
+					0x100000d 0x0000
+					0x100000f 0x0000
+				        0x1000010 0x0000
+					0x1000011 0x0007
+					0x1000012 0x0000
+					0x1000013 0x0000
+				        0x2000032
+					0x1000010 0x1590
+					0x1000011 0x0227
+				        0x2000032
+					0x1000012 0x009c
+				        0x2000032
+				        0x1000013 0x1900
+					0x1000029 0x0023
+					0x100002b 0x000e
+				        0x2000032
+				        0x1000020 0x0000
+					0x1000021 0x0000
+				        0x2000032
+					0x1000050 0x0000
+				        0x1000051 0x00ef
+					0x1000052 0x0000
+					0x1000053 0x013f
+					0x1000060 0xa700
+				        0x1000061 0x0001
+					0x100006a 0x0000
+					0x1000080 0x0000
+					0x1000081 0x0000
+				        0x1000082 0x0000
+					0x1000083 0x0000
+					0x1000084 0x0000
+					0x1000085 0x0000
+				        0x1000090 0x0010
+					0x1000092 0x0000
+					0x1000093 0x0003
+					0x1000095 0x0110
+				        0x1000097 0x0000
+					0x1000098 0x0000
+					0x1000007 0x0133
+					0x1000020 0x0000
+				        0x1000021 0x0000
+				        0x2000064>;
+				debug = <0>;
+			};
+
+			hy28b_ts: hy28b-ts@1 {
+				compatible = "ti,ads7846";
+				reg = <1>;
+
+				spi-max-frequency = <2000000>;
+				interrupts = <17 2>; /* high-to-low edge triggered */
+				interrupt-parent = <&gpio>;
+				pendown-gpio = <&gpio 17 0>;
+				ti,x-plate-ohms = /bits/ 16 <100>;
+				ti,pressure-max = /bits/ 16 <255>;
+			};
+		};
+	};
+	__overrides__ {
+		speed = 	<&hy28b>,"spi-max-frequency:0";
+		rotate = 	<&hy28b>,"rotate:0";
+		fps = 		<&hy28b>,"fps:0";
+		debug = 	<&hy28b>,"debug:0";
+		xohms =		<&hy28b_ts>,"ti,x-plate-ohms;0";
+		resetgpio =	<&hy28b>,"reset-gpios:4",
+				<&hy28b_pins>, "brcm,pins:1";
+		ledgpio =	<&hy28b>,"led-gpios:4",
+				<&hy28b_pins>, "brcm,pins:2";
+	};
+};

arch/arm/boot/dts/overlays/i2c-gpio-overlay.dts

@@ -0,0 +1,43 @@
+// Overlay for i2c_gpio bitbanging host bus.
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target-path = "/";
+		__overlay__ {
+			i2c_gpio: i2c@0 {
+				compatible = "i2c-gpio";
+				gpios = <&gpio 23 0 /* sda */
+					 &gpio 24 0 /* scl */
+					>;
+				i2c-gpio,delay-us = <2>;        /* ~100 kHz */
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+
+	fragment@1 {
+		target-path = "/aliases";
+		__overlay__ {
+			i2c_gpio = "/i2c@0";
+		};
+	};
+
+	fragment@2 {
+		target-path = "/__symbols__";
+		__overlay__ {
+			i2c_gpio = "/i2c@0";
+		};
+	};
+
+	__overrides__ {
+		i2c_gpio_sda = <&i2c_gpio>,"gpios:4";
+		i2c_gpio_scl = <&i2c_gpio>,"gpios:16";
+		i2c_gpio_delay_us = <&i2c_gpio>,"i2c-gpio,delay-us:0";
+	};
+};
+

arch/arm/boot/dts/overlays/i2c-mux-overlay.dts

@@ -0,0 +1,139 @@
+// Umbrella I2C Mux overlay
+
+/dts-v1/;
+/plugin/;
+
+/{
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&i2c_arm>;
+		__dormant__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			pca9542: mux@70 {
+				compatible = "nxp,pca9542";
+				reg = <0x70>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+				i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&i2c_arm>;
+		__dormant__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			pca9545: mux@70 {
+				compatible = "nxp,pca9545";
+				reg = <0x70>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+				i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+				i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+				i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&i2c_arm>;
+		__dormant__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			pca9548: mux@70 {
+				compatible = "nxp,pca9548";
+				reg = <0x70>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+				i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+				i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+				i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+				i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+				i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+				i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+				i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+		};
+	};
+
+	__overrides__ {
+		pca9542 = <0>, "+0";
+		pca9545 = <0>, "+1";
+		pca9548 = <0>, "+2";
+
+		addr =  <&pca9542>,"reg:0",
+			<&pca9545>,"reg:0",
+			<&pca9548>,"reg:0";
+	};
+};

arch/arm/boot/dts/overlays/i2c-pwm-pca9685a-overlay.dts

@@ -0,0 +1,26 @@
+// Definitions for NXP PCA9685A I2C PWM controller on ARM I2C bus.
+/dts-v1/;
+/plugin/;
+
+/{
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&i2c_arm>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			pca: pca@40 {
+				compatible = "nxp,pca9685";
+				#pwm-cells = <2>;
+				reg = <0x40>;
+				status = "okay";
+			};
+		};
+	};
+	__overrides__ {
+		addr = <&pca>,"reg:0";
+	};
+};

arch/arm/boot/dts/overlays/i2c-rtc-overlay.dts

@@ -0,0 +1,73 @@
+// Definitions for several I2C based Real Time Clocks
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&i2c_arm>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			ds1307: ds1307@68 {
+				compatible = "maxim,ds1307";
+				reg = <0x68>;
+				status = "disable";
+			};
+			ds1339: ds1339@68 {
+				compatible = "dallas,ds1339";
+				trickle-resistor-ohms = <0>;
+				reg = <0x68>;
+				status = "disable";
+			};
+			mcp7940x: mcp7940x@6f {
+				compatible = "microchip,mcp7940x";
+				reg = <0x6f>;
+				status = "disable";
+			};
+			mcp7941x: mcp7941x@6f {
+				compatible = "microchip,mcp7941x";
+				reg = <0x6f>;
+				status = "disable";
+			};
+			ds3231: ds3231@68 {
+				compatible = "maxim,ds3231";
+				reg = <0x68>;
+				status = "disable";
+			};
+			pcf2127: pcf2127@51 {
+				compatible = "nxp,pcf2127";
+				reg = <0x51>;
+				status = "disable";
+			};
+			pcf8523: pcf8523@68 {
+				compatible = "nxp,pcf8523";
+				reg = <0x68>;
+				status = "disable";
+			};
+			pcf8563: pcf8563@51 {
+				compatible = "nxp,pcf8563";
+				reg = <0x51>;
+				status = "disable";
+			};
+		};
+	};
+	__overrides__ {
+		ds1307 = <&ds1307>,"status";
+		ds1339 = <&ds1339>,"status";
+		ds3231 = <&ds3231>,"status";
+		mcp7940x = <&mcp7940x>,"status";
+		mcp7941x = <&mcp7941x>,"status";
+		pcf2127 = <&pcf2127>,"status";
+		pcf8523 = <&pcf8523>,"status";
+		pcf8563 = <&pcf8563>,"status";
+		trickle-resistor-ohms = <&ds1339>,"trickle-resistor-ohms:0";
+		wakeup-source = <&ds1339>,"wakeup-source?",
+				<&ds3231>,"wakeup-source?",
+				<&mcp7940x>,"wakeup-source?",
+				<&mcp7941x>,"wakeup-source?";
+	};
+};

arch/arm/boot/dts/overlays/i2c0-bcm2708-overlay.dts

@@ -0,0 +1,61 @@
+/*
+ * Device tree overlay for i2c_bcm2708, i2c0 bus
+ *
+ * Compile:
+ * dtc -@ -I dts -O dtb -o i2c0-bcm2708-overlay.dtb i2c0-bcm2708-overlay.dts
+ */
+
+/dts-v1/;
+/plugin/;
+
+/{
+   compatible = "brcm,bcm2708";
+
+   fragment@0 {
+      target = <&i2c0>;
+      __overlay__ {
+         status = "okay";
+      };
+   };
+
+   fragment@1 {
+      target = <&i2c0_pins>;
+      frag1: __overlay__ {
+         brcm,pins = <0 1>;
+         brcm,function = <4>; /* alt0 */
+      };
+   };
+
+   fragment@2 {
+      target = <&i2c0_pins>;
+      __dormant__ {
+         brcm,pins = <28 29>;
+         brcm,function = <4>; /* alt0 */
+      };
+   };
+
+   fragment@3 {
+      target = <&i2c0_pins>;
+      __dormant__ {
+         brcm,pins = <44 45>;
+         brcm,function = <5>; /* alt1 */
+      };
+   };
+
+   fragment@4 {
+      target = <&i2c0_pins>;
+      __dormant__ {
+         brcm,pins = <46 47>;
+         brcm,function = <4>; /* alt0 */
+      };
+   };
+
+   __overrides__ {
+      sda0_pin = <&frag1>,"brcm,pins:0";
+      scl0_pin = <&frag1>,"brcm,pins:4";
+      pins_0_1   = <0>,"+1-2-3-4";
+      pins_28_29 = <0>,"-1+2-3-4";
+      pins_44_45 = <0>,"-1-2+3-4";
+      pins_46_47 = <0>,"-1-2-3+4";
+   };
+};

arch/arm/boot/dts/overlays/i2c1-bcm2708-overlay.dts

@@ -0,0 +1,37 @@
+/*
+ * Device tree overlay for i2c_bcm2708, i2c1 bus
+ *
+ * Compile:
+ * dtc -@ -I dts -O dtb -o i2c1-bcm2708-overlay.dtb i2c1-bcm2708-overlay.dts
+ */
+
+/dts-v1/;
+/plugin/;
+
+/{
+   compatible = "brcm,bcm2708";
+
+   fragment@0 {
+      target = <&i2c1>;
+      __overlay__ {
+         pinctrl-0 = <&i2c1_pins>;
+         status = "okay";
+      };
+   };
+
+   fragment@1 {
+      target = <&gpio>;
+      __overlay__ {
+         i2c1_pins: i2c1 {
+            brcm,pins = <2 3>;
+            brcm,function = <4>; /* alt0 */
+         };
+      };
+   };
+
+   __overrides__ {
+      sda1_pin = <&i2c1_pins>,"brcm,pins:0";
+      scl1_pin = <&i2c1_pins>,"brcm,pins:4";
+      pin_func = <&i2c1_pins>,"brcm,function:0";
+   };
+};

arch/arm/boot/dts/overlays/i2s-gpio28-31-overlay.dts

@@ -0,0 +1,18 @@
+/*
+ * Device tree overlay to move i2s to gpio 28 to 31 on CM
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835", "brcm,bcm2836", "brcm,bcm2708", "brcm,bcm2709";
+
+	fragment@0 {
+		target = <&i2s_pins>;
+		__overlay__ {
+			brcm,pins = <28 29 30 31>;
+			brcm,function = <6>; /* alt2 */
+		};
+	};
+};

arch/arm/boot/dts/overlays/i2s-mmap-overlay.dts

@@ -0,0 +1,13 @@
+/dts-v1/;
+/plugin/;
+
+/{
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&i2s>;
+		__overlay__ {
+			brcm,enable-mmap;
+		};
+	};
+};

arch/arm/boot/dts/overlays/iqaudio-dac-overlay.dts

@@ -0,0 +1,43 @@
+// Definitions for IQaudIO DAC
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&i2s>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&i2c1>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			pcm5122@4c {
+				#sound-dai-cells = <0>;
+				compatible = "ti,pcm5122";
+				reg = <0x4c>;
+				status = "okay";
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&sound>;
+		frag2: __overlay__ {
+			compatible = "iqaudio,iqaudio-dac";
+			i2s-controller = <&i2s>;
+			status = "okay";
+		};
+	};
+
+	__overrides__ {
+		24db_digital_gain = <&frag2>,"iqaudio,24db_digital_gain?";
+	};
+};

arch/arm/boot/dts/overlays/iqaudio-dacplus-overlay.dts

@@ -0,0 +1,46 @@
+// Definitions for IQaudIO DAC+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&i2s>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&i2c1>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			pcm5122@4c {
+				#sound-dai-cells = <0>;
+				compatible = "ti,pcm5122";
+				reg = <0x4c>;
+				status = "okay";
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&sound>;
+		iqaudio_dac: __overlay__ {
+			compatible = "iqaudio,iqaudio-dac";
+			i2s-controller = <&i2s>;
+			mute-gpios = <&gpio 22 0>;
+			status = "okay";
+		};
+	};
+
+	__overrides__ {
+		24db_digital_gain = <&iqaudio_dac>,"iqaudio,24db_digital_gain?";
+		auto_mute_amp = <&iqaudio_dac>,"iqaudio-dac,auto-mute-amp?";
+		unmute_amp = <&iqaudio_dac>,"iqaudio-dac,unmute-amp?";
+	};
+};

arch/arm/boot/dts/overlays/justboom-dac-overlay.dts

@@ -0,0 +1,43 @@
+// Definitions for JustBoom DAC
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&i2s>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&i2c1>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			pcm5122@4d {
+				#sound-dai-cells = <0>;
+				compatible = "ti,pcm5122";
+				reg = <0x4d>;
+				status = "okay";
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&sound>;
+		frag2: __overlay__ {
+			compatible = "justboom,justboom-dac";
+			i2s-controller = <&i2s>;
+			status = "okay";
+		};
+	};
+
+	__overrides__ {
+		24db_digital_gain = <&frag2>,"justboom,24db_digital_gain?";
+	};
+};

arch/arm/boot/dts/overlays/justboom-digi-overlay.dts

@@ -0,0 +1,39 @@
+// Definitions for JustBoom Digi
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&i2s>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&i2c1>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			wm8804@3b {
+				#sound-dai-cells = <0>;
+				compatible = "wlf,wm8804";
+				reg = <0x3b>;
+				status = "okay";
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&sound>;
+		__overlay__ {
+			compatible = "justboom,justboom-digi";
+			i2s-controller = <&i2s>;
+			status = "okay";
+		};
+	};
+};

arch/arm/boot/dts/overlays/lirc-rpi-overlay.dts

@@ -0,0 +1,57 @@
+// Definitions for lirc-rpi module
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target-path = "/";
+		__overlay__ {
+			lirc_rpi: lirc_rpi {
+				compatible = "rpi,lirc-rpi";
+				pinctrl-names = "default";
+				pinctrl-0 = <&lirc_pins>;
+				status = "okay";
+
+				// Override autodetection of IR receiver circuit
+				// (0 = active high, 1 = active low, -1 = no override )
+				rpi,sense = <0xffffffff>;
+
+				// Software carrier
+				// (0 = off, 1 = on)
+				rpi,softcarrier = <1>;
+
+				// Invert output
+				// (0 = off, 1 = on)
+				rpi,invert = <0>;
+
+				// Enable debugging messages
+				// (0 = off, 1 = on)
+				rpi,debug = <0>;
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&gpio>;
+		__overlay__ {
+			lirc_pins: lirc_pins {
+				brcm,pins = <17 18>;
+				brcm,function = <1 0>; // out in
+				brcm,pull = <0 1>; // off down
+			};
+		};
+	};
+
+	__overrides__ {
+		gpio_out_pin =  <&lirc_pins>,"brcm,pins:0";
+		gpio_in_pin =   <&lirc_pins>,"brcm,pins:4";
+		gpio_in_pull =  <&lirc_pins>,"brcm,pull:4";
+
+		sense =         <&lirc_rpi>,"rpi,sense:0";
+		softcarrier =   <&lirc_rpi>,"rpi,softcarrier:0";
+		invert =        <&lirc_rpi>,"rpi,invert:0";
+		debug =         <&lirc_rpi>,"rpi,debug:0";
+	};
+};

arch/arm/boot/dts/overlays/mcp23017-overlay.dts

@@ -0,0 +1,54 @@
+// Definitions for MCP23017 Gpio Extender from Microchip Semiconductor
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
+
+	fragment@0 {
+		target = <&i2c1>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&gpio>;
+		__overlay__ {
+			mcp23017_pins: mcp23017_pins {
+				brcm,pins = <4>;
+				brcm,function = <0>;
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&i2c1>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			mcp23017: mcp@20 {
+				compatible = "microchip,mcp23017";
+				reg = <0x20>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				#interrupt-cells=<2>;
+				interrupt-parent = <&gpio>;
+				interrupts = <4 2>;
+				interrupt-controller;
+				microchip,irq-mirror;
+
+				status = "okay";
+			};
+		};
+	};
+	
+	__overrides__ {
+		gpiopin = <&mcp23017_pins>,"brcm,pins:0",
+				<&mcp23017>,"interrupts:0";
+		addr = <&mcp23017>,"reg:0";
+	};
+};
+

arch/arm/boot/dts/overlays/mcp2515-can0-overlay.dts

@@ -0,0 +1,73 @@
+/*
+ * Device tree overlay for mcp251x/can0 on spi0.0
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+    compatible = "brcm,bcm2835", "brcm,bcm2836", "brcm,bcm2708", "brcm,bcm2709";
+    /* disable spi-dev for spi0.0 */
+    fragment@0 {
+        target = <&spi0>;
+        __overlay__ {
+            status = "okay";
+        };
+    };
+
+    fragment@1 {
+	target = <&spidev0>;
+	__overlay__ {
+	    status = "disabled";
+	};
+    };
+
+    /* the interrupt pin of the can-controller */
+    fragment@2 {
+        target = <&gpio>;
+        __overlay__ {
+            can0_pins: can0_pins {
+                brcm,pins = <25>;
+                brcm,function = <0>; /* input */
+            };
+        };
+    };
+
+    /* the clock/oscillator of the can-controller */
+    fragment@3 {
+        target-path = "/clocks";
+        __overlay__ {
+            /* external oscillator of mcp2515 on SPI0.0 */
+            can0_osc: can0_osc {
+                compatible = "fixed-clock";
+                #clock-cells = <0>;
+                clock-frequency  = <16000000>;
+            };
+        };
+    };
+
+    /* the spi config of the can-controller itself binding everything together */
+    fragment@4 {
+        target = <&spi0>;
+        __overlay__ {
+            /* needed to avoid dtc warning */
+            #address-cells = <1>;
+            #size-cells = <0>;
+            can0: mcp2515@0 {
+                reg = <0>;
+                compatible = "microchip,mcp2515";
+                pinctrl-names = "default";
+                pinctrl-0 = <&can0_pins>;
+                spi-max-frequency = <10000000>;
+                interrupt-parent = <&gpio>;
+                interrupts = <25 0x2>;
+                clocks = <&can0_osc>;
+            };
+        };
+    };
+    __overrides__ {
+        oscillator = <&can0_osc>,"clock-frequency:0";
+        spimaxfrequency = <&can0>,"spi-max-frequency:0";
+        interrupt = <&can0_pins>,"brcm,pins:0",<&can0>,"interrupts:0";
+    };
+};

arch/arm/boot/dts/overlays/mcp2515-can1-overlay.dts

@@ -0,0 +1,73 @@
+/*
+ * Device tree overlay for mcp251x/can1 on spi0.1 edited by petit_miner
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+    compatible = "brcm,bcm2835", "brcm,bcm2836", "brcm,bcm2708", "brcm,bcm2709";
+    /* disable spi-dev for spi0.1 */
+    fragment@0 {
+        target = <&spi0>;
+        __overlay__ {
+            status = "okay";
+        };
+    };
+
+    fragment@1 {
+	target = <&spidev1>;
+	__overlay__ {
+	    status = "disabled";
+	};
+    };
+
+    /* the interrupt pin of the can-controller */
+    fragment@2 {
+        target = <&gpio>;
+        __overlay__ {
+            can1_pins: can1_pins {
+                brcm,pins = <25>;
+                brcm,function = <0>; /* input */
+            };
+        };
+    };
+
+    /* the clock/oscillator of the can-controller */
+    fragment@3 {
+        target-path = "/clocks";
+        __overlay__ {
+            /* external oscillator of mcp2515 on spi0.1 */
+            can1_osc: can1_osc {
+                compatible = "fixed-clock";
+                #clock-cells = <0>;
+                clock-frequency  = <16000000>;
+            };
+        };
+    };
+
+    /* the spi config of the can-controller itself binding everything together */
+    fragment@4 {
+        target = <&spi0>;
+        __overlay__ {
+            /* needed to avoid dtc warning */
+            #address-cells = <1>;
+            #size-cells = <0>;
+            can1: mcp2515@1 {
+                reg = <1>;
+                compatible = "microchip,mcp2515";
+                pinctrl-names = "default";
+                pinctrl-0 = <&can1_pins>;
+                spi-max-frequency = <10000000>;
+                interrupt-parent = <&gpio>;
+                interrupts = <25 0x2>;
+                clocks = <&can1_osc>;
+            };
+        };
+    };
+    __overrides__ {
+        oscillator = <&can1_osc>,"clock-frequency:0";
+        spimaxfrequency = <&can1>,"spi-max-frequency:0";
+        interrupt = <&can1_pins>,"brcm,pins:0",<&can1>,"interrupts:0";
+    };
+};

arch/arm/boot/dts/overlays/mmc-overlay.dts

@@ -0,0 +1,38 @@
+/dts-v1/;
+/plugin/;
+
+/{
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&mmc>;
+		frag0: __overlay__ {
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc_pins>;
+			bus-width = <4>;
+			brcm,overclock-50 = <0>;
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&gpio>;
+		__overlay__ {
+			mmc_pins: mmc_pins {
+				brcm,pins = <48 49 50 51 52 53>;
+				brcm,function = <7>; /* alt3 */
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&sdhost>;
+		__overlay__ {
+			status = "disabled";
+		};
+	};
+
+	__overrides__ {
+		overclock_50     = <&frag0>,"brcm,overclock-50:0";
+	};
+};

arch/arm/boot/dts/overlays/mz61581-overlay.dts

@@ -0,0 +1,117 @@
+/*
+ * Device Tree overlay for MZ61581-PI-EXT 2014.12.28 by Tontec
+ *
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
+
+	fragment@0 {
+		target = <&spi0>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&spidev0>;
+		__overlay__ {
+			status = "disabled";
+		};
+	};
+
+	fragment@2 {
+		target = <&spidev1>;
+		__overlay__ {
+			status = "disabled";
+		};
+	};
+
+	fragment@3 {
+		target = <&gpio>;
+		__overlay__ {
+			mz61581_pins: mz61581_pins {
+				brcm,pins = <4 15 18 25>;
+				brcm,function = <0 1 1 1>; /* in out out out */
+			};
+		};
+	};
+
+	fragment@4 {
+		target = <&spi0>;
+		__overlay__ {
+			/* needed to avoid dtc warning */
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			mz61581: mz61581@0{
+				compatible = "samsung,s6d02a1";
+				reg = <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&mz61581_pins>;
+
+				spi-max-frequency = <128000000>;
+				spi-cpol;
+				spi-cpha;
+
+				width = <320>;
+				height = <480>;
+				rotate = <270>;
+				bgr;
+				fps = <30>;
+				buswidth = <8>;
+				txbuflen = <32768>;
+
+				reset-gpios = <&gpio 15 0>;
+				dc-gpios = <&gpio 25 0>;
+				led-gpios = <&gpio 18 0>;
+
+				init = <0x10000b0 00
+					0x1000011
+					0x20000ff
+					0x10000b3 0x02 0x00 0x00 0x00
+					0x10000c0 0x13 0x3b 0x00 0x02 0x00 0x01 0x00 0x43
+					0x10000c1 0x08 0x16 0x08 0x08
+					0x10000c4 0x11 0x07 0x03 0x03
+					0x10000c6 0x00
+					0x10000c8 0x03 0x03 0x13 0x5c 0x03 0x07 0x14 0x08 0x00 0x21 0x08 0x14 0x07 0x53 0x0c 0x13 0x03 0x03 0x21 0x00
+					0x1000035 0x00
+					0x1000036 0xa0
+					0x100003a 0x55
+					0x1000044 0x00 0x01
+					0x10000d0 0x07 0x07 0x1d 0x03
+					0x10000d1 0x03 0x30 0x10
+					0x10000d2 0x03 0x14 0x04
+					0x1000029
+					0x100002c>;
+
+				/* This is a workaround to make sure the init sequence slows down and doesn't fail */
+				debug = <3>;
+			};
+
+			mz61581_ts: mz61581_ts@1 {
+				compatible = "ti,ads7846";
+				reg = <1>;
+
+				spi-max-frequency = <2000000>;
+				interrupts = <4 2>; /* high-to-low edge triggered */
+				interrupt-parent = <&gpio>;
+				pendown-gpio = <&gpio 4 0>;
+
+				ti,x-plate-ohms = /bits/ 16 <60>;
+				ti,pressure-max = /bits/ 16 <255>;
+			};
+		};
+	};
+	__overrides__ {
+		speed =   <&mz61581>, "spi-max-frequency:0";
+		rotate =  <&mz61581>, "rotate:0";
+		fps =     <&mz61581>, "fps:0";
+		txbuflen = <&mz61581>, "txbuflen:0";
+		debug =   <&mz61581>, "debug:0";
+		xohms =   <&mz61581_ts>,"ti,x-plate-ohms;0";
+	};
+};

arch/arm/boot/dts/overlays/pi3-act-led-overlay.dts

@@ -0,0 +1,27 @@
+/dts-v1/;
+/plugin/;
+
+/* Pi3 uses a GPIO expander to drive the LEDs which can only be accessed
+   from the VPU. There is a special driver for this with a separate DT node,
+   which has the unfortunate consequence of breaking the act_led_gpio and
+   act_led_activelow dtparams.
+
+   This overlay changes the GPIO controller back to the standard one and
+   restores the dtparams.
+*/
+
+/{
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&act_led>;
+		frag0: __overlay__ {
+			gpios = <&gpio 0 0>;
+		};
+	};
+
+	__overrides__ {
+		gpio = <&frag0>,"gpios:4";
+		activelow = <&frag0>,"gpios:8";
+	};
+};

arch/arm/boot/dts/overlays/pi3-disable-bt-overlay.dts

@@ -0,0 +1,46 @@
+/dts-v1/;
+/plugin/;
+
+/* Disable Bluetooth and restore UART0/ttyAMA0 over GPIOs 14 & 15.
+   To disable the systemd service that initialises the modem so it doesn't use
+   the UART:
+
+       sudo systemctl disable hciuart
+*/
+
+/{
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&uart1>;
+		__overlay__ {
+			status = "disabled";
+		};
+	};
+
+	fragment@1 {
+		target = <&uart0>;
+		__overlay__ {
+			pinctrl-names = "default";
+			pinctrl-0 = <&uart0_pins>;
+			status = "okay";
+		};
+	};
+
+	fragment@2 {
+		target = <&uart0_pins>;
+		__overlay__ {
+			brcm,pins;
+			brcm,function;
+			brcm,pull;
+		};
+	};
+
+	fragment@3 {
+		target-path = "/aliases";
+		__overlay__ {
+			serial0 = "/soc/uart@7e201000";
+			serial1 = "/soc/uart@7e215040";
+		};
+	};
+};

arch/arm/boot/dts/overlays/pi3-miniuart-bt-overlay.dts

@@ -0,0 +1,64 @@
+/dts-v1/;
+/plugin/;
+
+/* Switch Pi3 Bluetooth function to use the mini-UART (ttyS0) and restore
+   UART0/ttyAMA0 over GPIOs 14 & 15. Note that this may reduce the maximum
+   usable baudrate.
+
+   It is also necessary to edit /lib/systemd/system/hciuart.service and
+   replace ttyAMA0 with ttyS0, unless you have a system with udev rules
+   that create /dev/serial0 and /dev/serial1, in which case use /dev/serial1
+   instead because it will always be correct.
+
+   If cmdline.txt uses the alias serial0 to refer to the user-accessable port
+   then the firmware will replace with the appropriate port whether or not
+   this overlay is used.
+*/
+
+/{
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&uart0>;
+		__overlay__ {
+			pinctrl-names = "default";
+			pinctrl-0 = <&uart0_pins>;
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&uart1>;
+		__overlay__ {
+			pinctrl-names = "default";
+			pinctrl-0 = <&uart1_pins &bt_pins>;
+			status = "okay";
+		};
+	};
+
+	fragment@2 {
+		target = <&uart0_pins>;
+		__overlay__ {
+			brcm,pins;
+			brcm,function;
+			brcm,pull;
+		};
+	};
+
+	fragment@3 {
+		target = <&uart1_pins>;
+		__overlay__ {
+			brcm,pins = <32 33>;
+			brcm,function = <2>; /* alt5=UART1 */
+			brcm,pull = <0 2>;
+		};
+	};
+
+	fragment@4 {
+		target-path = "/aliases";
+		__overlay__ {
+			serial0 = "/soc/uart@7e201000";
+			serial1 = "/soc/uart@7e215040";
+		};
+	};
+};

arch/arm/boot/dts/overlays/piscreen-overlay.dts

@@ -0,0 +1,102 @@
+/*
+ * Device Tree overlay for PiScreen 3.5" display shield by Ozzmaker
+ *
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
+
+	fragment@0 {
+		target = <&spi0>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&spidev0>;
+		__overlay__ {
+			status = "disabled";
+		};
+	};
+
+	fragment@2 {
+		target = <&spidev1>;
+		__overlay__ {
+			status = "disabled";
+		};
+	};
+
+	fragment@3 {
+		target = <&gpio>;
+		__overlay__ {
+			piscreen_pins: piscreen_pins {
+				brcm,pins = <17 25 24 22>;
+				brcm,function = <0 1 1 1>; /* in out out out */
+			};
+		};
+	};
+
+	fragment@4 {
+		target = <&spi0>;
+		__overlay__ {
+			/* needed to avoid dtc warning */
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			piscreen: piscreen@0{
+				compatible = "ilitek,ili9486";
+				reg = <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&piscreen_pins>;
+
+				spi-max-frequency = <24000000>;
+				rotate = <270>;
+				bgr;
+				fps = <30>;
+				buswidth = <8>;
+				regwidth = <16>;
+				reset-gpios = <&gpio 25 0>;
+				dc-gpios = <&gpio 24 0>;
+				led-gpios = <&gpio 22 1>;
+				debug = <0>;
+
+				init = <0x10000b0 0x00
+				        0x1000011
+					0x20000ff
+					0x100003a 0x55
+					0x1000036 0x28
+					0x10000c2 0x44
+					0x10000c5 0x00 0x00 0x00 0x00
+					0x10000e0 0x0f 0x1f 0x1c 0x0c 0x0f 0x08 0x48 0x98 0x37 0x0a 0x13 0x04 0x11 0x0d 0x00
+					0x10000e1 0x0f 0x32 0x2e 0x0b 0x0d 0x05 0x47 0x75 0x37 0x06 0x10 0x03 0x24 0x20 0x00
+					0x10000e2 0x0f 0x32 0x2e 0x0b 0x0d 0x05 0x47 0x75 0x37 0x06 0x10 0x03 0x24 0x20 0x00
+					0x1000011
+					0x1000029>;
+			};
+
+			piscreen_ts: piscreen-ts@1 {
+				compatible = "ti,ads7846";
+				reg = <1>;
+
+				spi-max-frequency = <2000000>;
+				interrupts = <17 2>; /* high-to-low edge triggered */
+				interrupt-parent = <&gpio>;
+				pendown-gpio = <&gpio 17 0>;
+				ti,swap-xy;
+				ti,x-plate-ohms = /bits/ 16 <100>;
+				ti,pressure-max = /bits/ 16 <255>;
+			};
+		};
+	};
+	__overrides__ {
+		speed =		<&piscreen>,"spi-max-frequency:0";
+		rotate =	<&piscreen>,"rotate:0";
+		fps =		<&piscreen>,"fps:0";
+		debug =		<&piscreen>,"debug:0";
+		xohms =		<&piscreen_ts>,"ti,x-plate-ohms;0";
+	};
+};

arch/arm/boot/dts/overlays/piscreen2r-overlay.dts

@@ -0,0 +1,106 @@
+ /*
+ * Device Tree overlay for PiScreen2 3.5" TFT with resistive touch  by Ozzmaker.com
+ *
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
+
+	fragment@0 {
+		target = <&spi0>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&spidev0>;
+		__overlay__ {
+			status = "disabled";
+		};
+	};
+
+	fragment@2 {
+		target = <&spidev1>;
+		__overlay__ {
+			status = "disabled";
+		};
+	};
+
+	fragment@3 {
+		target = <&gpio>;
+		__overlay__ {
+			piscreen2_pins: piscreen2_pins {
+				brcm,pins = <17 25 24 22>;
+				brcm,function = <0 1 1 1>; /* in out out out */
+			};
+		};
+	};
+
+	fragment@4 {
+		target = <&spi0>;
+		__overlay__ {
+			/* needed to avoid dtc warning */
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			piscreen2: piscreen2@0{
+				compatible = "ilitek,ili9486";
+				reg = <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&piscreen2_pins>;
+				bgr;
+				spi-max-frequency = <64000000>;
+				rotate = <90>;
+				fps = <30>;
+				buswidth = <8>;
+				regwidth = <16>;
+				txbuflen = <32768>;
+				reset-gpios = <&gpio 25 0>;
+				dc-gpios = <&gpio 24 0>;
+				led-gpios = <&gpio 22 1>;
+				debug = <0>;
+
+                                init = <0x10000b0 0x00
+                                        0x1000011
+                                        0x20000ff
+                                        0x100003a 0x55
+                                        0x1000036 0x28
+                                        0x10000c0 0x11 0x09
+                                        0x10000c1 0x41
+                                        0x10000c5 0x00 0x00 0x00 0x00
+                                        0x10000b6 0x00 0x02
+                                        0x10000f7 0xa9 0x51 0x2c 0x2
+                                        0x10000be 0x00 0x04
+                                        0x10000e9 0x00
+                                        0x1000011
+                                        0x1000029>;
+
+			};
+
+			piscreen2_ts: piscreen2-ts@1 {
+				compatible = "ti,ads7846";
+				reg = <1>;
+
+				spi-max-frequency = <2000000>;
+				interrupts = <17 2>; /* high-to-low edge triggered */
+				interrupt-parent = <&gpio>;
+				pendown-gpio = <&gpio 17 0>;
+				ti,swap-xy;
+				ti,x-plate-ohms = /bits/ 16 <100>;
+				ti,pressure-max = /bits/ 16 <255>;
+			};
+		};
+	};
+	__overrides__ {
+		speed =		<&piscreen2>,"spi-max-frequency:0";
+		rotate =	<&piscreen2>,"rotate:0";
+		fps =		<&piscreen2>,"fps:0";
+		debug =		<&piscreen2>,"debug:0";
+		xohms =		<&piscreen2_ts>,"ti,x-plate-ohms;0";
+	};
+};
+

arch/arm/boot/dts/overlays/pitft22-overlay.dts

@@ -0,0 +1,69 @@
+/*
+ * Device Tree overlay for pitft by Adafruit
+ *
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+        compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
+
+        fragment@0 {
+                target = <&spi0>;
+                __overlay__ {
+                        status = "okay";
+
+                        spidev@0{
+                                status = "disabled";
+                        };
+
+                        spidev@1{
+                                status = "disabled";
+                        };
+                };
+        };
+
+        fragment@1 {
+                target = <&gpio>;
+                __overlay__ {
+                        pitft_pins: pitft_pins {
+                                brcm,pins = <25>;
+                                brcm,function = <1>; /* out */
+                                brcm,pull = <0>; /* none */
+                        };
+                };
+        };
+
+        fragment@2 {
+                target = <&spi0>;
+                __overlay__ {
+                        /* needed to avoid dtc warning */
+                        #address-cells = <1>;
+                        #size-cells = <0>;
+
+                        pitft: pitft@0{
+                                compatible = "ilitek,ili9340";
+                                reg = <0>;
+                                pinctrl-names = "default";
+                                pinctrl-0 = <&pitft_pins>;
+
+                                spi-max-frequency = <32000000>;
+                                rotate = <90>;
+                                fps = <25>;
+                                bgr;
+                                buswidth = <8>;
+                                dc-gpios = <&gpio 25 0>;
+                                debug = <0>;
+                        };
+
+                };
+        };
+
+        __overrides__ {
+                speed =   <&pitft>,"spi-max-frequency:0";
+                rotate =  <&pitft>,"rotate:0";
+                fps =     <&pitft>,"fps:0";
+                debug =   <&pitft>,"debug:0";
+        };
+};

arch/arm/boot/dts/overlays/pitft28-capacitive-overlay.dts

@@ -0,0 +1,91 @@
+/*
+ * Device Tree overlay for Adafruit PiTFT 2.8" capacitive touch screen
+ *
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+        compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
+
+        fragment@0 {
+                target = <&spi0>;
+                __overlay__ {
+                        status = "okay";
+                };
+        };
+
+	fragment@1 {
+		target = <&spidev0>;
+		__overlay__ {
+			status = "disabled";
+		};
+	};
+
+        fragment@2 {
+                target = <&gpio>;
+                __overlay__ {
+                        pitft_pins: pitft_pins {
+                                brcm,pins = <24 25>;
+                                brcm,function = <0 1>; /* in out */
+                                brcm,pull = <2 0>; /* pullup none */
+                        };
+                };
+        };
+
+        fragment@3 {
+                target = <&spi0>;
+                __overlay__ {
+                        /* needed to avoid dtc warning */
+                        #address-cells = <1>;
+                        #size-cells = <0>;
+
+                        pitft: pitft@0{
+                                compatible = "ilitek,ili9340";
+                                reg = <0>;
+                                pinctrl-names = "default";
+                                pinctrl-0 = <&pitft_pins>;
+
+                                spi-max-frequency = <32000000>;
+                                rotate = <90>;
+                                fps = <25>;
+                                bgr;
+                                buswidth = <8>;
+                                dc-gpios = <&gpio 25 0>;
+                                debug = <0>;
+                        };
+                };
+        };
+
+        fragment@4 {
+                target = <&i2c1>;
+                __overlay__ {
+                        /* needed to avoid dtc warning */
+                        #address-cells = <1>;
+                        #size-cells = <0>;
+
+                        ft6236: ft6236@38 {
+                                compatible = "focaltech,ft6236";
+                                reg = <0x38>;
+
+                                interrupt-parent = <&gpio>;
+                                interrupts = <24 2>;
+                                touchscreen-size-x = <240>;
+                                touchscreen-size-y = <320>;
+                        };
+                };
+        };
+
+        __overrides__ {
+                speed =   <&pitft>,"spi-max-frequency:0";
+                rotate =  <&pitft>,"rotate:0";
+                fps =     <&pitft>,"fps:0";
+                debug =   <&pitft>,"debug:0";
+                touch-sizex = <&ft6236>,"touchscreen-size-x?";
+                touch-sizey = <&ft6236>,"touchscreen-size-y?";
+                touch-invx  = <&ft6236>,"touchscreen-inverted-x?";
+                touch-invy  = <&ft6236>,"touchscreen-inverted-y?";
+                touch-swapxy = <&ft6236>,"touchscreen-swapped-x-y?";
+        };
+};

arch/arm/boot/dts/overlays/pitft28-resistive-overlay.dts

@@ -0,0 +1,121 @@
+/*
+ * Device Tree overlay for Adafruit PiTFT 2.8" resistive touch screen
+ *
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
+
+	fragment@0 {
+		target = <&spi0>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&spidev0>;
+		__overlay__ {
+			status = "disabled";
+		};
+	};
+
+	fragment@2 {
+		target = <&spidev1>;
+		__overlay__ {
+			status = "disabled";
+		};
+	};
+
+	fragment@3 {
+		target = <&gpio>;
+		__overlay__ {
+			pitft_pins: pitft_pins {
+				brcm,pins = <24 25>;
+				brcm,function = <0 1>; /* in out */
+				brcm,pull = <2 0>; /* pullup none */
+			};
+		};
+	};
+
+	fragment@4 {
+		target = <&spi0>;
+		__overlay__ {
+			/* needed to avoid dtc warning */
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			pitft: pitft@0{
+				compatible = "ilitek,ili9340";
+				reg = <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pitft_pins>;
+
+				spi-max-frequency = <32000000>;
+				rotate = <90>;
+				fps = <25>;
+				bgr;
+				buswidth = <8>;
+				dc-gpios = <&gpio 25 0>;
+				debug = <0>;
+			};
+
+			pitft_ts@1 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stmpe610";
+				reg = <1>;
+
+				spi-max-frequency = <500000>;
+				irq-gpio = <&gpio 24 0x2>; /* IRQF_TRIGGER_FALLING */
+				interrupts = <24 2>; /* high-to-low edge triggered */
+				interrupt-parent = <&gpio>;
+				interrupt-controller;
+
+				stmpe_touchscreen {
+					compatible = "st,stmpe-ts";
+					st,sample-time = <4>;
+					st,mod-12b = <1>;
+					st,ref-sel = <0>;
+					st,adc-freq = <2>;
+					st,ave-ctrl = <3>;
+					st,touch-det-delay = <4>;
+					st,settling = <2>;
+					st,fraction-z = <7>;
+					st,i-drive = <0>;
+				};
+
+				stmpe_gpio: stmpe_gpio {
+					#gpio-cells = <2>;
+					compatible = "st,stmpe-gpio";
+					/*
+					 * only GPIO2 is wired/available
+					 * and it is wired to the backlight
+					 */
+					st,norequest-mask = <0x7b>;
+				};
+			};
+		};
+	};
+
+	fragment@5 {
+		target-path = "/soc";
+		__overlay__ {
+			backlight {
+				compatible = "gpio-backlight";
+				gpios = <&stmpe_gpio 2 0>;
+				default-on;
+			};
+		};
+	};
+
+	__overrides__ {
+		speed =   <&pitft>,"spi-max-frequency:0";
+		rotate =  <&pitft>,"rotate:0";
+		fps =     <&pitft>,"fps:0";
+		debug =   <&pitft>,"debug:0";
+	};
+};

arch/arm/boot/dts/overlays/pps-gpio-overlay.dts

@@ -0,0 +1,34 @@
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+	fragment@0 {
+		target-path = "/";
+		__overlay__ {
+			pps: pps {
+				compatible = "pps-gpio";
+				pinctrl-names = "default";
+				pinctrl-0 = <&pps_pins>;
+				gpios = <&gpio 18 0>;
+				status = "okay";
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&gpio>;
+		__overlay__ {
+			pps_pins: pps_pins {
+				brcm,pins =     <18>;
+				brcm,function = <0>;    // in
+				brcm,pull =     <0>;    // off
+			};
+		};
+	};
+
+	__overrides__ {
+		gpiopin = <&pps>,"gpios:4",
+			  <&pps_pins>,"brcm,pins:0";
+	};
+};

arch/arm/boot/dts/overlays/pwm-2chan-overlay.dts

@@ -0,0 +1,53 @@
+/dts-v1/;
+/plugin/;
+
+/*
+This is the 2-channel overlay - only use it if you need both channels.
+
+Legal pin,function combinations for each channel:
+  PWM0: 12,4(Alt0) 18,2(Alt5) 40,4(Alt0)            52,5(Alt1)
+  PWM1: 13,4(Alt0) 19,2(Alt5) 41,4(Alt0) 45,4(Alt0) 53,5(Alt1)
+
+N.B.:
+  1) Pin 18 is the only one available on all platforms, and
+     it is the one used by the I2S audio interface.
+     Pins 12 and 13 might be better choices on an A+, B+ or Pi2.
+  2) The onboard analogue audio output uses both PWM channels.
+  3) So be careful mixing audio and PWM.
+*/
+
+/ {
+	fragment@0 {
+		target = <&gpio>;
+		__overlay__ {
+			pwm_pins: pwm_pins {
+				brcm,pins = <18 19>;
+				brcm,function = <2 2>; /* Alt5 */
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&pwm>;
+		__overlay__ {
+			pinctrl-names = "default";
+			pinctrl-0 = <&pwm_pins>;
+			status = "okay";
+		};
+	};
+
+	fragment@2 {
+		target = <&clk_pwm>;
+		frag2: __overlay__ {
+			clock-frequency = <100000000>;
+		};
+	};
+
+	__overrides__ {
+		pin   = <&pwm_pins>,"brcm,pins:0";
+		pin2  = <&pwm_pins>,"brcm,pins:4";
+		func  = <&pwm_pins>,"brcm,function:0";
+		func2 = <&pwm_pins>,"brcm,function:4";
+		clock = <&frag2>,"clock-frequency:0";
+	};
+};

arch/arm/boot/dts/overlays/pwm-overlay.dts

@@ -0,0 +1,49 @@
+/dts-v1/;
+/plugin/;
+
+/*
+Legal pin,function combinations for each channel:
+  PWM0: 12,4(Alt0) 18,2(Alt5) 40,4(Alt0)            52,5(Alt1)
+  PWM1: 13,4(Alt0) 19,2(Alt5) 41,4(Alt0) 45,4(Alt0) 53,5(Alt1)
+
+N.B.:
+  1) Pin 18 is the only one available on all platforms, and
+     it is the one used by the I2S audio interface.
+     Pins 12 and 13 might be better choices on an A+, B+ or Pi2.
+  2) The onboard analogue audio output uses both PWM channels.
+  3) So be careful mixing audio and PWM.
+*/
+
+/ {
+	fragment@0 {
+		target = <&gpio>;
+		__overlay__ {
+			pwm_pins: pwm_pins {
+				brcm,pins = <18>;
+				brcm,function = <2>; /* Alt5 */
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&pwm>;
+		__overlay__ {
+			pinctrl-names = "default";
+			pinctrl-0 = <&pwm_pins>;
+			status = "okay";
+		};
+	};
+
+	fragment@2 {
+		target = <&clk_pwm>;
+		frag2: __overlay__ {
+			clock-frequency = <100000000>;
+		};
+	};
+
+	__overrides__ {
+		pin   = <&pwm_pins>,"brcm,pins:0";
+		func  = <&pwm_pins>,"brcm,function:0";
+		clock = <&frag2>,"clock-frequency:0";
+	};
+};

arch/arm/boot/dts/overlays/qca7000-overlay.dts

@@ -0,0 +1,52 @@
+// Overlay for the Qualcomm Atheros QCA7000 on I2SE's PLC Stamp micro EVK
+// Visit: https://www.i2se.com/product/plc-stamp-micro-evk for details
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&spi0>;
+		__overlay__ {
+			/* needed to avoid dtc warning */
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "okay";
+
+			spidev@0 {
+				status = "disabled";
+			};
+
+			eth1: qca7000@0 {
+				compatible = "qca,qca7000";
+				reg = <0>; /* CE0 */
+				pinctrl-names = "default";
+				pinctrl-0 = <&eth1_pins>;
+				interrupt-parent = <&gpio>;
+				interrupts = <23 0x1>; /* rising edge */
+				spi-max-frequency = <12000000>;
+				status = "okay";
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&gpio>;
+		__overlay__ {
+			eth1_pins: eth1_pins {
+				brcm,pins = <23>;
+				brcm,function = <0>; /* in */
+				brcm,pull = <0>; /* none */
+			};
+		};
+	};
+
+	__overrides__ {
+		int_pin = <&eth1>, "interrupts:0",
+		          <&eth1_pins>, "brcm,pins:0";
+		speed   = <&eth1>, "spi-max-frequency:0";
+	};
+};

arch/arm/boot/dts/overlays/raspidac3-overlay.dts

@@ -0,0 +1,45 @@
+// Definitions for RaspiDACv3
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&i2s>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&i2c1>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			pcm5122@4c {
+				#sound-dai-cells = <0>;
+				compatible = "ti,pcm5122";
+				reg = <0x4c>;
+				status = "okay";
+			};
+
+			tpa6130a2: tpa6130a2@60 {
+				compatible = "ti,tpa6130a2";
+				reg = <0x60>;
+				status = "okay";
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&sound>;
+		__overlay__ {
+			compatible = "jg,raspidacv3";
+			i2s-controller = <&i2s>;
+			status = "okay";
+		};
+	};
+};

arch/arm/boot/dts/overlays/rpi-backlight-overlay.dts

@@ -0,0 +1,21 @@
+/*
+ * Devicetree overlay for mailbox-driven Raspberry Pi DSI Display
+ * backlight controller
+ */
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target-path = "/";
+		__overlay__ {
+			rpi_backlight: rpi_backlight {
+				compatible = "raspberrypi,rpi-backlight";
+				firmware = <&firmware>;
+				status = "okay";
+			};
+		};
+	};
+};

arch/arm/boot/dts/overlays/rpi-dac-overlay.dts

@@ -0,0 +1,34 @@
+// Definitions for RPi DAC
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2708";
+
+	fragment@0 {
+		target = <&i2s>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target-path = "/";
+		__overlay__ {
+			pcm1794a-codec {
+				#sound-dai-cells = <0>;
+				compatible = "ti,pcm1794a";
+				status = "okay";
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&sound>;
+		__overlay__ {
+			compatible = "rpi,rpi-dac";
+			i2s-controller = <&i2s>;
+			status = "okay";
+		};
+	};
+};

arch/arm/boot/dts/overlays/rpi-display-overlay.dts

@@ -0,0 +1,89 @@
+/*
+ * Device Tree overlay for rpi-display by Watterott
+ *
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
+
+	fragment@0 {
+		target = <&spi0>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&spidev0>;
+		__overlay__ {
+			status = "disabled";
+		};
+	};
+
+	fragment@2 {
+		target = <&spidev1>;
+		__overlay__ {
+			status = "disabled";
+		};
+	};
+
+	fragment@3 {
+		target = <&gpio>;
+		__overlay__ {
+			rpi_display_pins: rpi_display_pins {
+				brcm,pins = <18 23 24 25>;
+				brcm,function = <1 1 1 0>; /* out out out in */
+				brcm,pull = <0 0 0 2>; /* - - - up */
+			};
+		};
+	};
+
+	fragment@4 {
+		target = <&spi0>;
+		__overlay__ {
+			/* needed to avoid dtc warning */
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			rpidisplay: rpi-display@0{
+				compatible = "ilitek,ili9341";
+				reg = <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&rpi_display_pins>;
+
+				spi-max-frequency = <32000000>;
+				rotate = <270>;
+				bgr;
+				fps = <30>;
+				buswidth = <8>;
+				reset-gpios = <&gpio 23 0>;
+				dc-gpios = <&gpio 24 0>;
+				led-gpios = <&gpio 18 1>;
+				debug = <0>;
+			};
+
+			rpidisplay_ts: rpi-display-ts@1 {
+				compatible = "ti,ads7846";
+				reg = <1>;
+
+				spi-max-frequency = <2000000>;
+				interrupts = <25 2>; /* high-to-low edge triggered */
+				interrupt-parent = <&gpio>;
+				pendown-gpio = <&gpio 25 0>;
+				ti,x-plate-ohms = /bits/ 16 <60>;
+				ti,pressure-max = /bits/ 16 <255>;
+			};
+		};
+	};
+	__overrides__ {
+		speed =   <&rpidisplay>,"spi-max-frequency:0";
+		rotate =  <&rpidisplay>,"rotate:0";
+		fps =     <&rpidisplay>,"fps:0";
+		debug =   <&rpidisplay>,"debug:0";
+		xohms =   <&rpidisplay_ts>,"ti,x-plate-ohms;0";
+		swapxy =  <&rpidisplay_ts>,"ti,swap-xy?";
+	};
+};