commit 2e70570656 upstream.
A new warning in clang points out a place in this file where a bitwise
OR is being used with boolean types:
drivers/gpu/drm/i915/intel_pm.c:3066:12: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
changed = ilk_increase_wm_latency(dev_priv, dev_priv->wm.pri_latency, 12) |
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
This construct is intentional, as it allows every one of the calls to
ilk_increase_wm_latency() to occur (instead of short circuiting with
logical OR) while still caring about the result of each call.
To make this clearer to the compiler, use the '|=' operator to assign
the result of each ilk_increase_wm_latency() call to changed, which
keeps the meaning of the code the same but makes it obvious that every
one of these calls is expected to happen.
Link: https://github.com/ClangBuiltLinux/linux/issues/1473
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Suggested-by: Dávid Bolvanský <david.bolvansky@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211014211916.3550122-1-nathan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 502408a61f upstream.
A new warning in clang points out a place in this file where a bitwise
OR is being used with boolean expressions:
In file included from drivers/staging/wlan-ng/prism2usb.c:2:
drivers/staging/wlan-ng/hfa384x_usb.c:3787:7: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
((test_and_clear_bit(THROTTLE_RX, &hw->usb_flags) &&
~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/staging/wlan-ng/hfa384x_usb.c:3787:7: note: cast one or both operands to int to silence this warning
1 warning generated.
The comment explains that short circuiting here is undesirable, as the
calls to test_and_{clear,set}_bit() need to happen for both sides of the
expression.
Clang's suggestion would work to silence the warning but the readability
of the expression would suffer even more. To clean up the warning and
make the block more readable, use a variable for each side of the
bitwise expression.
Link: https://github.com/ClangBuiltLinux/linux/issues/1478
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20211014215703.3705371-1-nathan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7e67b8e80 upstream.
Currently, if CONFIG_RANDOM_TRUST_BOOTLOADER is enabled, multiple calls
to add_bootloader_randomness() are broken and can cause a NULL pointer
dereference, as noted by Ivan T. Ivanov. This is not only a hypothetical
problem, as qemu on arm64 may provide bootloader entropy via EFI and via
devicetree.
On the first call to add_hwgenerator_randomness(), crng_fast_load() is
executed, and if the seed is long enough, crng_init will be set to 1.
On subsequent calls to add_bootloader_randomness() and then to
add_hwgenerator_randomness(), crng_fast_load() will be skipped. Instead,
wait_event_interruptible() and then credit_entropy_bits() will be called.
If the entropy count for that second seed is large enough, that proceeds
to crng_reseed().
However, both wait_event_interruptible() and crng_reseed() depends
(at least in numa_crng_init()) on workqueues. Therefore, test whether
system_wq is already initialized, which is a sufficient indicator that
workqueue_init_early() has progressed far enough.
If we wind up hitting the !system_wq case, we later want to do what
would have been done there when wqs are up, so set a flag, and do that
work later from the rand_initialize() call.
Reported-by: Ivan T. Ivanov <iivanov@suse.de>
Fixes: 18b915ac6b ("efi/random: Treat EFI_RNG_PROTOCOL output as bootloader randomness")
Cc: stable@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
[Jason: added crng_need_done state and related logic.]
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 009ba8568b upstream.
_extract_crng() does plain loads of crng->init_time and
crng_global_init_time, which causes undefined behavior if
crng_reseed() and RNDRESEEDCRNG modify these corrently.
Use READ_ONCE() and WRITE_ONCE() to make the behavior defined.
Don't fix the race on crng->init_time by protecting it with crng->lock,
since it's not a problem for duplicate reseedings to occur. I.e., the
lockless access with READ_ONCE() is fine.
Fixes: d848e5f8e1 ("random: add new ioctl RNDRESEEDCRNG")
Fixes: e192be9d9a ("random: replace non-blocking pool with a Chacha20-based CRNG")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d73d1e320 upstream.
extract_crng() and crng_backtrack_protect() load crng_node_pool with a
plain load, which causes undefined behavior if do_numa_crng_init()
modifies it concurrently.
Fix this by using READ_ONCE(). Note: as per the previous discussion
https://lore.kernel.org/lkml/20211219025139.31085-1-ebiggers@kernel.org/T/#u,
READ_ONCE() is believed to be sufficient here, and it was requested that
it be used here instead of smp_load_acquire().
Also change do_numa_crng_init() to set crng_node_pool using
cmpxchg_release() instead of mb() + cmpxchg(), as the former is
sufficient here but is more lightweight.
Fixes: 1e7f583af6 ("random: make /dev/urandom scalable for silly userspace programs")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a8737ff06 upstream.
The received data contains the channel the received data is associated
with. If the channel number is bigger than the actual number of
channels assume broken or malicious USB device and shut it down.
This fixes the error found by clang:
| drivers/net/can/usb/gs_usb.c:386:6: error: variable 'dev' is used
| uninitialized whenever 'if' condition is true
| if (hf->channel >= GS_MAX_INTF)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
| drivers/net/can/usb/gs_usb.c:474:10: note: uninitialized use occurs here
| hf, dev->gs_hf_size, gs_usb_receive_bulk_callback,
| ^~~
Link: https://lore.kernel.org/all/20211210091158.408326-1-mkl@pengutronix.de
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c9e143084d upstream.
The runtime PM callback may be called as soon as the runtime PM facility
is enabled and activated. It means that ->suspend() may be called before
we finish probing the device in the ACPI case. Hence, NULL pointer
dereference:
intel-lpss INT34BA:00: IRQ index 0 not found
BUG: kernel NULL pointer dereference, address: 0000000000000030
...
Workqueue: pm pm_runtime_work
RIP: 0010:intel_lpss_suspend+0xb/0x40 [intel_lpss]
To fix this, first try to register the device and only after that enable
runtime PM facility.
Fixes: 4b45efe852 ("mfd: Add support for Intel Sunrisepoint LPSS devices")
Reported-by: Orlando Chamberlain <redecorating@protonmail.com>
Reported-by: Aditya Garg <gargaditya08@live.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Aditya Garg <gargaditya08@live.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211101190008.86473-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 710ad98c36 upstream.
Laurent reported that they have seen a significant amount of TCP retransmissions
at high throughput from applications residing in network namespaces talking to
the outside world via veths. The drops were seen on the qdisc layer (fq_codel,
as per systemd default) of the phys device such as ena or virtio_net due to all
traffic hitting a _single_ TX queue _despite_ multi-queue device. (Note that the
setup was _not_ using XDP on veths as the issue is generic.)
More specifically, after edbea92202 ("veth: Store queue_mapping independently
of XDP prog presence") which made it all the way back to v4.19.184+,
skb_record_rx_queue() would set skb->queue_mapping to 1 (given 1 RX and 1 TX
queue by default for veths) instead of leaving at 0.
This is eventually retained and callbacks like ena_select_queue() will also pick
single queue via netdev_core_pick_tx()'s ndo_select_queue() once all the traffic
is forwarded to that device via upper stack or other means. Similarly, for others
not implementing ndo_select_queue() if XPS is disabled, netdev_pick_tx() might
call into the skb_tx_hash() and check for prior skb_rx_queue_recorded() as well.
In general, it is a _bad_ idea for virtual devices like veth to mess around with
queue selection [by default]. Given dev->real_num_tx_queues is by default 1,
the skb->queue_mapping was left untouched, and so prior to edbea92202 the
netdev_core_pick_tx() could do its job upon __dev_queue_xmit() on the phys device.
Unbreak this and restore prior behavior by removing the skb_record_rx_queue()
from veth_xmit() altogether.
If the veth peer has an XDP program attached, then it would return the first RX
queue index in xdp_md->rx_queue_index (unless configured in non-default manner).
However, this is still better than breaking the generic case.
Fixes: edbea92202 ("veth: Store queue_mapping independently of XDP prog presence")
Fixes: 638264dc90 ("veth: Support per queue XDP ring")
Reported-by: Laurent Bernaille <laurent.bernaille@datadoghq.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Cc: Toshiaki Makita <toshiaki.makita1@gmail.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Toshiaki Makita <toshiaki.makita1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a658c929de upstream.
If cfg80211 is providing extraie's for a scanning process then ath11k will
copy that over to the firmware. The extraie.len is a 32 bit value in struct
element_info and describes the amount of bytes for the vendor information
elements.
The WMI_TLV packet is having a special WMI_TAG_ARRAY_BYTE section. This
section can have a (payload) length up to 65535 bytes because the
WMI_TLV_LEN can store up to 16 bits. The code was missing such a check and
could have created a scan request which cannot be parsed correctly by the
firmware.
But the bigger problem was the allocation of the buffer. It has to align
the TLV sections by 4 bytes. But the code was using an u8 to store the
newly calculated length of this section (with alignment). And the new
calculated length was then used to allocate the skbuff. But the actual code
to copy in the data is using the extraie.len and not the calculated
"aligned" length.
The length of extraie with IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS enabled
was 264 bytes during tests with a QCA Milan card. But it only allocated 8
bytes (264 bytes % 256) for it. As consequence, the code to memcpy the
extraie into the skb was then just overwriting data after skb->end. Things
like shinfo were therefore corrupted. This could usually be seen by a crash
in skb_zcopy_clear which tried to call a ubuf_info callback (using a bogus
address).
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-02892.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Cc: stable@vger.kernel.org
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211207142913.1734635-1-sven@narfation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d7d4c0793 upstream.
When the USB core code for getting root-hub status reports was
originally written, it was assumed that the hub driver would be its
only caller. But this isn't true now; user programs can use usbfs to
communicate with root hubs and get status reports. When they do this,
they may use a transfer_buffer that is smaller than the data returned
by the HCD, which will lead to a buffer overflow error when
usb_hcd_poll_rh_status() tries to store the status data. This was
discovered by syzbot:
BUG: KASAN: slab-out-of-bounds in memcpy include/linux/fortify-string.h:225 [inline]
BUG: KASAN: slab-out-of-bounds in usb_hcd_poll_rh_status+0x5f4/0x780 drivers/usb/core/hcd.c:776
Write of size 2 at addr ffff88801da403c0 by task syz-executor133/4062
This patch fixes the bug by reducing the amount of status data if it
won't fit in the transfer_buffer. If some data gets discarded then
the URB's completion status is set to -EOVERFLOW rather than 0, to let
the user know what happened.
Reported-and-tested-by: syzbot+3ae6a2b06f131ab9849f@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Yc+3UIQJ2STbxNua@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f663729bb upstream.
Bugzilla #213839 reports a 7-port hub that doesn't work properly when
devices are plugged into some of the ports; the kernel goes into an
unending disconnect/reinitialize loop as shown in the bug report.
This "7-port hub" comprises two four-port hubs with one plugged into
the other; the failures occur when a device is plugged into one of the
downstream hub's ports. (These hubs have other problems too. For
example, they bill themselves as USB-2.0 compliant but they only run
at full speed.)
It turns out that the failures are caused by bugs in both the kernel
and the hub. The hub's bug is that it reports a different
bmAttributes value in its configuration descriptor following a remote
wakeup (0xe0 before, 0xc0 after -- the wakeup-support bit has
changed).
The kernel's bug is inside the hub driver's resume handler. When
hub_activate() sees that one of the hub's downstream ports got a
wakeup request from a child device, it notes this fact by setting the
corresponding bit in the hub->change_bits variable. But this variable
is meant for connection changes, not wakeup events; setting it causes
the driver to believe the downstream port has been disconnected and
then connected again (in addition to having received a wakeup
request).
Because of this, the hub driver then tries to check whether the device
currently plugged into the downstream port is the same as the device
that had been attached there before. Normally this check succeeds and
wakeup handling continues with no harm done (which is why the bug
remained undetected until now). But with these dodgy hubs, the check
fails because the config descriptor has changed. This causes the hub
driver to reinitialize the child device, leading to the
disconnect/reinitialize loop described in the bug report.
The proper way to note reception of a downstream wakeup request is
to set a bit in the hub->event_bits variable instead of
hub->change_bits. That way the hub driver will realize that something
has happened to the port but will not think the port and child device
have been disconnected. This patch makes that change.
Cc: <stable@vger.kernel.org>
Tested-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YdCw7nSfWYPKWQoD@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5e6fa7a12 upstream.
Add the missing bulk-out endpoint sanity check to probe() to avoid
division by zero in bfusb_send_frame() in case a malicious device has
broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4f ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ no upstream commit given implicitly fixed through the larger refactoring
in c25b2ae136 ]
While auditing some other code, I noticed missing checks inside the pointer
arithmetic simulation, more specifically, adjust_ptr_min_max_vals(). Several
*_OR_NULL types are not rejected whereas they are _required_ to be rejected
given the expectation is that they get promoted into a 'real' pointer type
for the success case, that is, after an explicit != NULL check.
One case which stands out and is accessible from unprivileged (iff enabled
given disabled by default) is BPF ring buffer. From crafting a PoC, the NULL
check can be bypassed through an offset, and its id marking will then lead
to promotion of mem_or_null to a mem type.
bpf_ringbuf_reserve() helper can trigger this case through passing of reserved
flags, for example.
func#0 @0
0: R1=ctx(id=0,off=0,imm=0) R10=fp0
0: (7a) *(u64 *)(r10 -8) = 0
1: R1=ctx(id=0,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm
1: (18) r1 = 0x0
3: R1_w=map_ptr(id=0,off=0,ks=0,vs=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm
3: (b7) r2 = 8
4: R1_w=map_ptr(id=0,off=0,ks=0,vs=0,imm=0) R2_w=invP8 R10=fp0 fp-8_w=mmmmmmmm
4: (b7) r3 = 0
5: R1_w=map_ptr(id=0,off=0,ks=0,vs=0,imm=0) R2_w=invP8 R3_w=invP0 R10=fp0 fp-8_w=mmmmmmmm
5: (85) call bpf_ringbuf_reserve#131
6: R0_w=mem_or_null(id=2,ref_obj_id=2,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm refs=2
6: (bf) r6 = r0
7: R0_w=mem_or_null(id=2,ref_obj_id=2,off=0,imm=0) R6_w=mem_or_null(id=2,ref_obj_id=2,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm refs=2
7: (07) r0 += 1
8: R0_w=mem_or_null(id=2,ref_obj_id=2,off=1,imm=0) R6_w=mem_or_null(id=2,ref_obj_id=2,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm refs=2
8: (15) if r0 == 0x0 goto pc+4
R0_w=mem(id=0,ref_obj_id=0,off=0,imm=0) R6_w=mem(id=0,ref_obj_id=2,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm refs=2
9: R0_w=mem(id=0,ref_obj_id=0,off=0,imm=0) R6_w=mem(id=0,ref_obj_id=2,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm refs=2
9: (62) *(u32 *)(r6 +0) = 0
R0_w=mem(id=0,ref_obj_id=0,off=0,imm=0) R6_w=mem(id=0,ref_obj_id=2,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm refs=2
10: R0_w=mem(id=0,ref_obj_id=0,off=0,imm=0) R6_w=mem(id=0,ref_obj_id=2,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm refs=2
10: (bf) r1 = r6
11: R0_w=mem(id=0,ref_obj_id=0,off=0,imm=0) R1_w=mem(id=0,ref_obj_id=2,off=0,imm=0) R6_w=mem(id=0,ref_obj_id=2,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm refs=2
11: (b7) r2 = 0
12: R0_w=mem(id=0,ref_obj_id=0,off=0,imm=0) R1_w=mem(id=0,ref_obj_id=2,off=0,imm=0) R2_w=invP0 R6_w=mem(id=0,ref_obj_id=2,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm refs=2
12: (85) call bpf_ringbuf_submit#132
13: R6=invP(id=0) R10=fp0 fp-8=mmmmmmmm
13: (b7) r0 = 0
14: R0_w=invP0 R6=invP(id=0) R10=fp0 fp-8=mmmmmmmm
14: (95) exit
from 8 to 13: safe
processed 15 insns (limit 1000000) max_states_per_insn 0 total_states 1 peak_states 1 mark_read 0
OK
All three commits, that is b121b341e5 ("bpf: Add PTR_TO_BTF_ID_OR_NULL support"),
457f44363a ("bpf: Implement BPF ring buffer and verifier support for it"), and the
afbf21dce6 ("bpf: Support readonly/readwrite buffers in verifier") suffer the same
cause and their *_OR_NULL type pendants must be rejected in adjust_ptr_min_max_vals().
Make the test more robust by reusing reg_type_may_be_null() helper such that we catch
all *_OR_NULL types we have today and in future.
Note that pointer arithmetic on PTR_TO_BTF_ID, PTR_TO_RDONLY_BUF, and PTR_TO_RDWR_BUF
is generally allowed.
Fixes: b121b341e5 ("bpf: Add PTR_TO_BTF_ID_OR_NULL support")
Fixes: 457f44363a ("bpf: Implement BPF ring buffer and verifier support for it")
Fixes: afbf21dce6 ("bpf: Support readonly/readwrite buffers in verifier")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07edfece8b upstream.
At CPU-hotplug time, unbind_worker() may preempt a worker while it is
waking up. In that case the following scenario can happen:
unbind_workers() wq_worker_running()
-------------- -------------------
if (!(worker->flags & WORKER_NOT_RUNNING))
//PREEMPTED by unbind_workers
worker->flags |= WORKER_UNBOUND;
[...]
atomic_set(&pool->nr_running, 0);
//resume to worker
atomic_inc(&worker->pool->nr_running);
After unbind_worker() resets pool->nr_running, the value is expected to
remain 0 until the pool ever gets rebound in case cpu_up() is called on
the target CPU in the future. But here the race leaves pool->nr_running
with a value of 1, triggering the following warning when the worker goes
idle:
WARNING: CPU: 3 PID: 34 at kernel/workqueue.c:1823 worker_enter_idle+0x95/0xc0
Modules linked in:
CPU: 3 PID: 34 Comm: kworker/3:0 Not tainted 5.16.0-rc1+ #34
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba527-rebuilt.opensuse.org 04/01/2014
Workqueue: 0x0 (rcu_par_gp)
RIP: 0010:worker_enter_idle+0x95/0xc0
Code: 04 85 f8 ff ff ff 39 c1 7f 09 48 8b 43 50 48 85 c0 74 1b 83 e2 04 75 99 8b 43 34 39 43 30 75 91 8b 83 00 03 00 00 85 c0 74 87 <0f> 0b 5b c3 48 8b 35 70 f1 37 01 48 8d 7b 48 48 81 c6 e0 93 0
RSP: 0000:ffff9b7680277ed0 EFLAGS: 00010086
RAX: 00000000ffffffff RBX: ffff93465eae9c00 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffff9346418a0000 RDI: ffff934641057140
RBP: ffff934641057170 R08: 0000000000000001 R09: ffff9346418a0080
R10: ffff9b768027fdf0 R11: 0000000000002400 R12: ffff93465eae9c20
R13: ffff93465eae9c20 R14: ffff93465eae9c70 R15: ffff934641057140
FS: 0000000000000000(0000) GS:ffff93465eac0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 000000001cc0c000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
worker_thread+0x89/0x3d0
? process_one_work+0x400/0x400
kthread+0x162/0x190
? set_kthread_struct+0x40/0x40
ret_from_fork+0x22/0x30
</TASK>
Also due to this incorrect "nr_running == 1", further queued work may
end up not being served, because no worker is awaken at work insert time.
This raises rcutorture writer stalls for example.
Fix this with disabling preemption in the right place in
wq_worker_running().
It's worth noting that if the worker migrates and runs concurrently with
unbind_workers(), it is guaranteed to see the WORKER_UNBOUND flag update
due to set_cpus_allowed_ptr() acquiring/releasing rq->lock.
Fixes: 6d25be5782 ("sched/core, workqueues: Distangle worker accounting from rq lock")
Reviewed-by: Lai Jiangshan <jiangshanlai@gmail.com>
Tested-by: Paul E. McKenney <paulmck@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Daniel Bristot de Oliveira <bristot@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move from only supporting the default of pre-multiplied
alpha to supporting user specified blend mode using the
standardised property.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
We are using mode->crt_clock here which is filled by drm_mode_set_crtcinfo()
which is called right after .mode_valid.
Use mode->clock which is valid here.
Fixes: 624d93a4f0 ("drm/vc4: hdmi: Move clock calculation into its own function")
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Still under investigation, but the conditions under which the HVS
will accept values written to the gamma PWL are not straightforward.
Disable gamma on HVS5 again until it can be resolved to avoid
gamma being enabled with an incorrect table.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Replace the cfi directives with the UNWIND equivalents. This prevents
the .eh_frame section from being created, eliminating the warnings.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
With the automatic VL805 support being removed from the standard
CM4 dtb (since most CM4 carriers don't have a VL805), retain support
on those that do by creating a "vl805" overlay that restores the
deleted "usb@0,0" node.
The "vl805" overlay will be loaded automatically (after an upcoming
firmware update) on CM4 boards where the EEPROM config includes the
setting VL805=1.
See: https://forums.raspberrypi.com/viewtopic.php?t=326088
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
commit cf73ed894e upstream.
Since irq request is the last thing in the driver probe, it happens
later than the input device registration. This means that there is a
small time window where if the open method is called the driver will
attempt to enable not yet available irq.
Fix that by moving the irq request before the input device registration.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Fixes: 26822652c8 ("Input: add zinitix touchscreen driver")
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20220106072840.36851-2-nikita@trvn.ru
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8b5fdfc57c ]
As we build for mips, we meet following error. l1_init error with
multiple definition. Some architecture devices usually marked with
l1, l2, lxx as the start-up phase. so we change the mISDN function
names, align with Isdnl2_xxx.
mips-linux-gnu-ld: drivers/isdn/mISDN/layer1.o: in function `l1_init':
(.text+0x890): multiple definition of `l1_init'; \
arch/mips/kernel/bmips_5xxx_init.o:(.text+0xf0): first defined here
make[1]: *** [home/mips/kernel-build/linux/Makefile:1161: vmlinux] Error 1
Signed-off-by: wolfgang huang <huangjinhui@kylinos.cn>
Reported-by: k2ci <kernel-bot@kylinos.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1833c3964 ]
The "__ip6_tnl_parm" struct was left uninitialized causing an invalid
load of random data when the "__ip6_tnl_parm" struct was used elsewhere.
As an example, in the function "ip6_tnl_xmit_ctl()", it tries to access
the "collect_md" member. With "__ip6_tnl_parm" being uninitialized and
containing random data, the UBSAN detected that "collect_md" held a
non-boolean value.
The UBSAN issue is as follows:
===============================================================
UBSAN: invalid-load in net/ipv6/ip6_tunnel.c:1025:14
load of value 30 is not a valid value for type '_Bool'
CPU: 1 PID: 228 Comm: kworker/1:3 Not tainted 5.16.0-rc4+ #8
Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
Workqueue: ipv6_addrconf addrconf_dad_work
Call Trace:
<TASK>
dump_stack_lvl+0x44/0x57
ubsan_epilogue+0x5/0x40
__ubsan_handle_load_invalid_value+0x66/0x70
? __cpuhp_setup_state+0x1d3/0x210
ip6_tnl_xmit_ctl.cold.52+0x2c/0x6f [ip6_tunnel]
vti6_tnl_xmit+0x79c/0x1e96 [ip6_vti]
? lock_is_held_type+0xd9/0x130
? vti6_rcv+0x100/0x100 [ip6_vti]
? lock_is_held_type+0xd9/0x130
? rcu_read_lock_bh_held+0xc0/0xc0
? lock_acquired+0x262/0xb10
dev_hard_start_xmit+0x1e6/0x820
__dev_queue_xmit+0x2079/0x3340
? mark_lock.part.52+0xf7/0x1050
? netdev_core_pick_tx+0x290/0x290
? kvm_clock_read+0x14/0x30
? kvm_sched_clock_read+0x5/0x10
? sched_clock_cpu+0x15/0x200
? find_held_lock+0x3a/0x1c0
? lock_release+0x42f/0xc90
? lock_downgrade+0x6b0/0x6b0
? mark_held_locks+0xb7/0x120
? neigh_connected_output+0x31f/0x470
? lockdep_hardirqs_on+0x79/0x100
? neigh_connected_output+0x31f/0x470
? ip6_finish_output2+0x9b0/0x1d90
? rcu_read_lock_bh_held+0x62/0xc0
? ip6_finish_output2+0x9b0/0x1d90
ip6_finish_output2+0x9b0/0x1d90
? ip6_append_data+0x330/0x330
? ip6_mtu+0x166/0x370
? __ip6_finish_output+0x1ad/0xfb0
? nf_hook_slow+0xa6/0x170
ip6_output+0x1fb/0x710
? nf_hook.constprop.32+0x317/0x430
? ip6_finish_output+0x180/0x180
? __ip6_finish_output+0xfb0/0xfb0
? lock_is_held_type+0xd9/0x130
ndisc_send_skb+0xb33/0x1590
? __sk_mem_raise_allocated+0x11cf/0x1560
? dst_output+0x4a0/0x4a0
? ndisc_send_rs+0x432/0x610
addrconf_dad_completed+0x30c/0xbb0
? addrconf_rs_timer+0x650/0x650
? addrconf_dad_work+0x73c/0x10e0
addrconf_dad_work+0x73c/0x10e0
? addrconf_dad_completed+0xbb0/0xbb0
? rcu_read_lock_sched_held+0xaf/0xe0
? rcu_read_lock_bh_held+0xc0/0xc0
process_one_work+0x97b/0x1740
? pwq_dec_nr_in_flight+0x270/0x270
worker_thread+0x87/0xbf0
? process_one_work+0x1740/0x1740
kthread+0x3ac/0x490
? set_kthread_struct+0x100/0x100
ret_from_fork+0x22/0x30
</TASK>
===============================================================
The solution is to initialize "__ip6_tnl_parm" struct to zeros in the
"vti6_siocdevprivate()" function.
Signed-off-by: William Zhao <wizhao@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 80211be1b9 upstream.
Instead of one shot run of ADC at beginning of charging, run continuous
conversion to ensure that all charging-related values are monitored
properly (input voltage, input current, themperature etc.).
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29262e1f77 upstream.
Hytera makes a range of digital (DMR) radios. These radios can be
programmed to a allow a computer to control them over Ethernet over USB,
either using NCM or RNDIS.
This commit adds support for RNDIS for Hytera radios. I tested with a
Hytera PD785 and a Hytera MD785G. When these radios are programmed to
set up a Radio to PC Network using RNDIS, an USB interface will be added
with class 2 (Communications), subclass 2 (Abstract Modem Control) and
an interface protocol of 255 ("vendor specific" - lsusb even hints "MSFT
RNDIS?").
This patch is similar to the solution of this StackOverflow user, but
that only works for the Hytera MD785:
https://stackoverflow.com/a/53550858
To use the "Radio to PC Network" functionality of Hytera DMR radios, the
radios need to be programmed correctly in CPS (Hytera's Customer
Programming Software). "Forward to PC" should be checked in "Network"
(under "General Setting" in "Conventional") and the "USB Network
Communication Protocol" should be set to RNDIS.
Signed-off-by: Thomas Toye <thomas@toye.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 644106cdb8 upstream.
A new commit in LLVM causes an error on the use of 'long double' when
'-mno-x87' is used, which the kernel does through an alias,
'-mno-80387' (see the LLVM commit below for more details around why it
does this).
drivers/power/reset/ltc2952-poweroff.c:162:28: error: expression requires 'long double' type support, but target 'x86_64-unknown-linux-gnu' does not support it
data->wde_interval = 300L * 1E6L;
^
drivers/power/reset/ltc2952-poweroff.c:162:21: error: expression requires 'long double' type support, but target 'x86_64-unknown-linux-gnu' does not support it
data->wde_interval = 300L * 1E6L;
^
drivers/power/reset/ltc2952-poweroff.c:163:41: error: expression requires 'long double' type support, but target 'x86_64-unknown-linux-gnu' does not support it
data->trigger_delay = ktime_set(2, 500L*1E6L);
^
3 errors generated.
This happens due to the use of a 'long double' literal. The 'E6' part of
'1E6L' causes the literal to be a 'double' then the 'L' suffix promotes
it to 'long double'.
There is no visible reason for floating point values in this driver, as
the values are only assigned to integer types. Use NSEC_PER_MSEC, which
is the same integer value as '1E6L', to avoid changing functionality but
fix the error.
Fixes: 6647156c00 ("power: reset: add LTC2952 poweroff driver")
Link: https://github.com/ClangBuiltLinux/linux/issues/1497
Link: a8083d42b1
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5055dc0348 upstream.
The role of ena_calc_max_io_queue_num() is to return the number
of queues supported by the device, which means the return value
should be >=0.
The function that calls ena_calc_max_io_queue_num(), checks
the return value. If it is 0, it means the device reported
it supports 0 IO queues. This case is considered an error
and is handled by the calling function accordingly.
However the current implementation of ena_calc_max_io_queue_num()
is wrong, since when it detects the device supports 0 IO queues,
it returns -EFAULT.
In such a case the calling function doesn't detect the error,
and therefore doesn't handle it.
This commit changes ena_calc_max_io_queue_num() to return 0
in case the device reported it supports 0 queues, allowing the
calling function to properly handle the error case.
Fixes: 736ce3f414 ("net: ena: make ethtool -l show correct max number of queues")
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c255a34e02 upstream.
ena_com_tx_comp_req_id_get() checks the req_id of a received completion,
and if it is out of bounds returns -EINVAL. This is a sign that
something is wrong with the device and it needs to be reset.
The current code does not reset the device in this case, which leaves
the driver in an undefined state, where this completion is not properly
handled.
This commit adds a call to handle_invalid_req_id() in ena_clean_tx_irq()
and ena_clean_xdp_irq() which resets the device to fix the issue.
This commit also removes unnecessary request id checks from
validate_tx_req_id() and validate_xdp_req_id(). This check is unneeded
because it was already performed in ena_com_tx_comp_req_id_get(), which
is called right before these functions.
Fixes: 548c4940b9 ("net: ena: Implement XDP_TX action")
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d18a07897 upstream.
tx_queue_len can be set to ~0U, we need to be more
careful about overflows.
__fls(0) is undefined, as this report shows:
UBSAN: shift-out-of-bounds in net/sched/sch_qfq.c:1430:24
shift exponent 51770272 is too large for 32-bit type 'int'
CPU: 0 PID: 25574 Comm: syz-executor.0 Not tainted 5.16.0-rc7-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x201/0x2d8 lib/dump_stack.c:106
ubsan_epilogue lib/ubsan.c:151 [inline]
__ubsan_handle_shift_out_of_bounds+0x494/0x530 lib/ubsan.c:330
qfq_init_qdisc+0x43f/0x450 net/sched/sch_qfq.c:1430
qdisc_create+0x895/0x1430 net/sched/sch_api.c:1253
tc_modify_qdisc+0x9d9/0x1e20 net/sched/sch_api.c:1660
rtnetlink_rcv_msg+0x934/0xe60 net/core/rtnetlink.c:5571
netlink_rcv_skb+0x200/0x470 net/netlink/af_netlink.c:2496
netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
netlink_unicast+0x814/0x9f0 net/netlink/af_netlink.c:1345
netlink_sendmsg+0xaea/0xe60 net/netlink/af_netlink.c:1921
sock_sendmsg_nosec net/socket.c:704 [inline]
sock_sendmsg net/socket.c:724 [inline]
____sys_sendmsg+0x5b9/0x910 net/socket.c:2409
___sys_sendmsg net/socket.c:2463 [inline]
__sys_sendmsg+0x280/0x370 net/socket.c:2492
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
Fixes: 462dbc9101 ("pkt_sched: QFQ Plus: fair-queueing service at DRR cost")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 938f2e0b57 upstream.
The addition of routable multicast TX handling introduced a
bug/regression for packets with a link-local multicast destination:
These packets would be sent to all batman-adv nodes with a multicast
router and to all batman-adv nodes with an old version without multicast
router detection.
This even disregards the batman-adv multicast fanout setting, which can
potentially lead to an unwanted, high number of unicast transmissions or
even congestion.
Fixing this by avoiding to send link-local multicast packets to nodes in
the multicast router list.
Fixes: 11d458c1cb ("batman-adv: mcast: apply optimizations for routable packets, too")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8bda81a4d4 upstream.
lwtunnel_valid_encap_type_attr is used to validate encap attributes
within a multipath route. Add length validation checking to the type.
lwtunnel_valid_encap_type_attr is called converting attributes to
fib{6,}_config struct which means it is used before fib_get_nhs,
ip6_route_multipath_add, and ip6_route_multipath_del - other
locations that use rtnh_ok and then nla_get_u16 on RTA_ENCAP_TYPE
attribute.
Fixes: 9ed59592e3 ("lwtunnel: fix autoload of lwt modules")
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4619bcf913 upstream.
Commit referenced in the Fixes tag used nla_memcpy for RTA_GATEWAY as
does the current nla_get_in6_addr. nla_memcpy protects against accessing
memory greater than what is in the attribute, but there is no check
requiring the attribute to have an IPv6 address. Add it.
Fixes: 51ebd31815 ("ipv6: add support of equal cost multipath (ECMP)")
Signed-off-by: David Ahern <dsahern@kernel.org>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0daf5cb217 upstream.
There's another compilation fail (first here [1]) reported by kernel
test robot for W=1 clang build:
>> samples/ftrace/ftrace-direct-multi-modify.c:7:6: warning: no previous
prototype for function 'my_direct_func1' [-Wmissing-prototypes]
void my_direct_func1(unsigned long ip)
Direct functions in ftrace direct sample modules need to have prototypes
defined. They are already global in order to be visible for the inline
assembly, so there's no problem.
The kernel test robot reported just error for ftrace-direct-multi-modify,
but I got same errors also for the rest of the modules touched by this patch.
[1] 67d4f6e3bf ftrace/samples: Add missing prototype for my_direct_func
Link: https://lkml.kernel.org/r/20211219135317.212430-1-jolsa@kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Fixes: e1067a07cf ("ftrace/samples: Add module to test multi direct modify interface")
Fixes: ae0cc3b7e7 ("ftrace/samples: Add a sample module that implements modify_ftrace_direct()")
Fixes: 156473a0ff ("ftrace: Add another example of register_ftrace_direct() use case")
Fixes: b06457c83a ("ftrace: Add sample module that uses register_ftrace_direct()")
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e738451d78 upstream.
There was a wrong queues representation in sysfs during
driver's reinitialization in case of online cpus number is
less than combined queues. It was caused by stopped
NetworkManager, which is responsible for calling vsi_open
function during driver's initialization.
In specific situation (ex. 12 cpus online) there were 16 queues
in /sys/class/net/<iface>/queues. In case of modifying queues with
value higher, than number of online cpus, then it caused write
errors and other errors.
Add updating of sysfs's queues representation during driver
initialization.
Fixes: 41c445ff0f ("i40e: main driver core")
Signed-off-by: Lukasz Cieplicki <lukaszx.cieplicki@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40feded8a2 upstream.
When loading the i40e driver, it prints a message like: 'The driver for the
device detected a newer version of the NVM image v1.x than expected v1.y.
Please install the most recent version of the network driver.' This is
misleading as the driver is working as expected.
Fix that by removing the second part of message and changing it from
dev_info to dev_dbg.
Fixes: 4fb29bddb5 ("i40e: The driver now prints the API version in error message")
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68a18ad713 upstream.
Clang static analysis reports this warnings
mlme.c:5332:7: warning: Branch condition evaluates to a
garbage value
have_higher_than_11mbit)
^~~~~~~~~~~~~~~~~~~~~~~
have_higher_than_11mbit is only set to true some of the time in
ieee80211_get_rates() but is checked all of the time. So
have_higher_than_11mbit needs to be initialized to false.
Fixes: 5d6a1b069b ("mac80211: set basic rates earlier")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20211223162848.3243702-1-trix@redhat.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3087a6f36e upstream.
This code used to copy in an unsigned long worth of data before
the sockptr_t conversion, so restore that.
Fixes: a7b75c5a8c ("net: pass a sockptr_t into ->setsockopt")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b35a0f4dd5 upstream.
If dst->is_global field is not set, the GRH fields are not cleared
and the following infoleak is reported.
=====================================================
BUG: KMSAN: kernel-infoleak in instrument_copy_to_user include/linux/instrumented.h:121 [inline]
BUG: KMSAN: kernel-infoleak in _copy_to_user+0x1c9/0x270 lib/usercopy.c:33
instrument_copy_to_user include/linux/instrumented.h:121 [inline]
_copy_to_user+0x1c9/0x270 lib/usercopy.c:33
copy_to_user include/linux/uaccess.h:209 [inline]
ucma_init_qp_attr+0x8c7/0xb10 drivers/infiniband/core/ucma.c:1242
ucma_write+0x637/0x6c0 drivers/infiniband/core/ucma.c:1732
vfs_write+0x8ce/0x2030 fs/read_write.c:588
ksys_write+0x28b/0x510 fs/read_write.c:643
__do_sys_write fs/read_write.c:655 [inline]
__se_sys_write fs/read_write.c:652 [inline]
__ia32_sys_write+0xdb/0x120 fs/read_write.c:652
do_syscall_32_irqs_on arch/x86/entry/common.c:114 [inline]
__do_fast_syscall_32+0x96/0xf0 arch/x86/entry/common.c:180
do_fast_syscall_32+0x34/0x70 arch/x86/entry/common.c:205
do_SYSENTER_32+0x1b/0x20 arch/x86/entry/common.c:248
entry_SYSENTER_compat_after_hwframe+0x4d/0x5c
Local variable resp created at:
ucma_init_qp_attr+0xa4/0xb10 drivers/infiniband/core/ucma.c:1214
ucma_write+0x637/0x6c0 drivers/infiniband/core/ucma.c:1732
Bytes 40-59 of 144 are uninitialized
Memory access of size 144 starts at ffff888167523b00
Data copied to user address 0000000020000100
CPU: 1 PID: 25910 Comm: syz-executor.1 Not tainted 5.16.0-rc5-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
=====================================================
Fixes: 4ba66093bd ("IB/core: Check for global flag when using ah_attr")
Link: https://lore.kernel.org/r/0e9dd51f93410b7b2f4f5562f52befc878b71afa.1641298868.git.leonro@nvidia.com
Reported-by: syzbot+6d532fa8f9463da290bc@syzkaller.appspotmail.com
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b712941c80 upstream.
In the absence of this validation, if the user requests to
configure queues more than the enabled queues, it results in
sending the requested number of queues to the kernel stack
(due to the asynchronous nature of VF response), in which
case the stack might pick a queue to transmit that is not
enabled and result in Tx hang. Fix this bug by
limiting the total number of queues allocated for VF to
active queues of VF.
Fixes: d5b33d0244 ("i40evf: add ndo_setup_tc callback to i40evf")
Signed-off-by: Ashwin Vijayavel <ashwin.vijayavel@intel.com>
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 01cbf50877 upstream.
Hide i40e opcode information sent during response to VF in case when
untrusted VF tried to change MAC on the VF interface.
This is implemented by adding an additional parameter 'hide' to the
response sent to VF function that hides the display of error
information, but forwards the error code to VF.
Previously it was not possible to send response with some error code
to VF without displaying opcode information.
Fixes: 5c3c48ac6b ("i40e: implement virtual device interface")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Reviewed-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 754e438235 upstream.
Alexander reported a use of uninitialized value in
atusb_set_extended_addr(), that is caused by reading 0 bytes via
usb_control_msg().
Fix it by validating if the number of bytes transferred is actually
correct, since usb_control_msg() may read less bytes, than was requested
by caller.
Fail log:
BUG: KASAN: uninit-cmp in ieee802154_is_valid_extended_unicast_addr include/linux/ieee802154.h:310 [inline]
BUG: KASAN: uninit-cmp in atusb_set_extended_addr drivers/net/ieee802154/atusb.c:1000 [inline]
BUG: KASAN: uninit-cmp in atusb_probe.cold+0x29f/0x14db drivers/net/ieee802154/atusb.c:1056
Uninit value used in comparison: 311daa649a2003bd stack handle: 000000009a2003bd
ieee802154_is_valid_extended_unicast_addr include/linux/ieee802154.h:310 [inline]
atusb_set_extended_addr drivers/net/ieee802154/atusb.c:1000 [inline]
atusb_probe.cold+0x29f/0x14db drivers/net/ieee802154/atusb.c:1056
usb_probe_interface+0x314/0x7f0 drivers/usb/core/driver.c:396
Fixes: 7490b008d1 ("ieee802154: add support for atusb transceiver")
Reported-by: Alexander Potapenko <glider@google.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/20220104182806.7188-1-paskripkin@gmail.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 823e670f7e upstream.
With the new osnoise tracer, we are seeing the below splat:
Kernel attempted to read user page (c7d880000) - exploit attempt? (uid: 0)
BUG: Unable to handle kernel data access on read at 0xc7d880000
Faulting instruction address: 0xc0000000002ffa10
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Radix SMP NR_CPUS=2048 NUMA pSeries
...
NIP [c0000000002ffa10] __trace_array_vprintk.part.0+0x70/0x2f0
LR [c0000000002ff9fc] __trace_array_vprintk.part.0+0x5c/0x2f0
Call Trace:
[c0000008bdd73b80] [c0000000001c49cc] put_prev_task_fair+0x3c/0x60 (unreliable)
[c0000008bdd73be0] [c000000000301430] trace_array_printk_buf+0x70/0x90
[c0000008bdd73c00] [c0000000003178b0] trace_sched_switch_callback+0x250/0x290
[c0000008bdd73c90] [c000000000e70d60] __schedule+0x410/0x710
[c0000008bdd73d40] [c000000000e710c0] schedule+0x60/0x130
[c0000008bdd73d70] [c000000000030614] interrupt_exit_user_prepare_main+0x264/0x270
[c0000008bdd73de0] [c000000000030a70] syscall_exit_prepare+0x150/0x180
[c0000008bdd73e10] [c00000000000c174] system_call_vectored_common+0xf4/0x278
osnoise tracer on ppc64le is triggering osnoise_taint() for negative
duration in get_int_safe_duration() called from
trace_sched_switch_callback()->thread_exit().
The problem though is that the check for a valid trace_percpu_buffer is
incorrect in get_trace_buf(). The check is being done after calculating
the pointer for the current cpu, rather than on the main percpu pointer.
Fix the check to be against trace_percpu_buffer.
Link: https://lkml.kernel.org/r/a920e4272e0b0635cf20c444707cbce1b2c8973d.1640255304.git.naveen.n.rao@linux.vnet.ibm.com
Cc: stable@vger.kernel.org
Fixes: e2ace00117 ("tracing: Choose static tp_printk buffer by explicit nesting count")
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5c0042200 upstream.
As Yi Zhuang reported in bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=214299
There is potential deadlock during quota data flush as below:
Thread A: Thread B:
f2fs_dquot_acquire
down_read(&sbi->quota_sem)
f2fs_write_checkpoint
block_operations
f2fs_look_all
down_write(&sbi->cp_rwsem)
f2fs_quota_write
f2fs_write_begin
__do_map_lock
f2fs_lock_op
down_read(&sbi->cp_rwsem)
__need_flush_qutoa
down_write(&sbi->quota_sem)
This patch changes block_operations() to use trylock, if it fails,
it means there is potential quota data updater, in this condition,
let's flush quota data first and then trylock again to check dirty
status of quota data.
The side effect is: in heavy race condition (e.g. multi quota data
upaters vs quota data flusher), it may decrease the probability of
synchronizing quota data successfully in checkpoint() due to limited
retry time of quota flush.
Reported-by: Yi Zhuang <zhuangyi1@huawei.com>
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To allow for the cases where a simple panel does have a GPIO
controlled backlight. Defaults to having no backlight defined.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Use GitHubs issue form for bug reports.
- modern look
- user don't need to mess with given markdown parts while filling the issue template
Setup config.yml for general questions and problems with the Raspbian distribution packages.
The driver did allow the exposure to go up to VTS - 4 lines,
but this would produce a visible line on 1280x800, and a stall of
the sensor at 640x480.
Whilst it appears to work with a difference of 5, the datasheet states
there should be at least 25 lines difference between VTS and exposure,
so use that value.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
commit 08389d8882 upstream.
Add a kconfig knob which allows for unprivileged bpf to be disabled by default.
If set, the knob sets /proc/sys/kernel/unprivileged_bpf_disabled to value of 2.
This still allows a transition of 2 -> {0,1} through an admin. Similarly,
this also still keeps 1 -> {1} behavior intact, so that once set to permanently
disabled, it cannot be undone aside from a reboot.
We've also added extra2 with max of 2 for the procfs handler, so that an admin
still has a chance to toggle between 0 <-> 2.
Either way, as an additional alternative, applications can make use of CAP_BPF
that we added a while ago.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/74ec548079189e4e4dffaeb42b8987bb3c852eee.1620765074.git.daniel@iogearbox.net
Cc: Salvatore Bonaccorso <carnil@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e22e45fc9e upstream.
A real world panic issue was found as follow in Linux 5.4.
BUG: unable to handle page fault for address: ffffde49a863de28
PGD 7e6fe62067 P4D 7e6fe62067 PUD 7e6fe63067 PMD f51e064067 PTE 0
RIP: 0010:tw_timer_handler+0x20/0x40
Call Trace:
<IRQ>
call_timer_fn+0x2b/0x120
run_timer_softirq+0x1ef/0x450
__do_softirq+0x10d/0x2b8
irq_exit+0xc7/0xd0
smp_apic_timer_interrupt+0x68/0x120
apic_timer_interrupt+0xf/0x20
This issue was also reported since 2017 in the thread [1],
unfortunately, the issue was still can be reproduced after fixing
DCCP.
The ipv4_mib_exit_net is called before tcp_sk_exit_batch when a net
namespace is destroyed since tcp_sk_ops is registered befrore
ipv4_mib_ops, which means tcp_sk_ops is in the front of ipv4_mib_ops
in the list of pernet_list. There will be a use-after-free on
net->mib.net_statistics in tw_timer_handler after ipv4_mib_exit_net
if there are some inflight time-wait timers.
This bug is not introduced by commit f2bf415cfe ("mib: add net to
NET_ADD_STATS_BH") since the net_statistics is a global variable
instead of dynamic allocation and freeing. Actually, commit
61a7e26028 ("mib: put net statistics on struct net") introduces
the bug since it put net statistics on struct net and free it when
net namespace is destroyed.
Moving init_ipv4_mibs() to the front of tcp_init() to fix this bug
and replace pr_crit() with panic() since continuing is meaningless
when init_ipv4_mibs() fails.
[1] https://groups.google.com/g/syzkaller/c/p1tn-_Kc6l4/m/smuL_FMAAgAJ?pli=1
Fixes: 61a7e26028 ("mib: put net statistics on struct net")
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Cc: Cong Wang <cong.wang@bytedance.com>
Cc: Fam Zheng <fam.zheng@bytedance.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211228104145.9426-1-songmuchun@bytedance.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 142c779d05 upstream.
The PVSCSI implementation in the VMware hypervisor under specific
configuration ("SCSI Bus Sharing" set to "Physical") returns zero dataLen
in the completion descriptor for READ CAPACITY(16). As a result, the kernel
can not detect proper disk geometry. This can be recognized by the kernel
message:
[ 0.776588] sd 1:0:0:0: [sdb] Sector size 0 reported, assuming 512.
The PVSCSI implementation in QEMU does not set dataLen at all, keeping it
zeroed. This leads to a boot hang as was reported by Shmulik Ladkani.
It is likely that the controller returns the garbage at the end of the
buffer. Residual length should be set by the driver in that case. The SCSI
layer will erase corresponding data. See commit bdb2b8cab4 ("[SCSI] erase
invalid data returned by device") for details.
Commit e662502b3a ("scsi: vmw_pvscsi: Set correct residual data length")
introduced the issue by setting residual length unconditionally, causing
the SCSI layer to erase the useful payload beyond dataLen when this value
is returned as 0.
As a result, considering existing issues in implementations of PVSCSI
controllers, we do not want to call scsi_set_resid() when dataLen ==
0. Calling scsi_set_resid() has no effect if dataLen equals buffer length.
Link: https://lore.kernel.org/lkml/20210824120028.30d9c071@blondie/
Link: https://lore.kernel.org/r/20211220190514.55935-1-amakhalov@vmware.com
Fixes: e662502b3a ("scsi: vmw_pvscsi: Set correct residual data length")
Cc: Matt Wang <wwentao@vmware.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Vishal Bhakta <vbhakta@vmware.com>
Cc: VMware PV-Drivers <pv-drivers@vmware.com>
Cc: James E.J. Bottomley <jejb@linux.ibm.com>
Cc: linux-scsi@vger.kernel.org
Cc: stable@vger.kernel.org
Reported-and-suggested-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Alexey Makhalov <amakhalov@vmware.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cfd0d84ba2 upstream.
In 4.13, commit 74310e06be ("android: binder: Move buffer out of area shared with user space")
fixed a kernel structure visibility issue. As part of that patch,
sizeof(void *) was used as the buffer size for 0-length data payloads so
the driver could detect abusive clients sending 0-length asynchronous
transactions to a server by enforcing limits on async_free_size.
Unfortunately, on the "free" side, the accounting of async_free_space
did not add the sizeof(void *) back. The result was that up to 8-bytes of
async_free_space were leaked on every async transaction of 8-bytes or
less. These small transactions are uncommon, so this accounting issue
has gone undetected for several years.
The fix is to use "buffer_size" (the allocated buffer size) instead of
"size" (the logical buffer size) when updating the async_free_space
during the free operation. These are the same except for this
corner case of asynchronous transactions with payloads < 8 bytes.
Fixes: 74310e06be ("android: binder: Move buffer out of area shared with user space")
Signed-off-by: Todd Kjos <tkjos@google.com>
Cc: stable@vger.kernel.org # 4.14+
Link: https://lore.kernel.org/r/20211220190150.2107077-1-tkjos@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e484409258 upstream.
The Fresco Logic FL1100 controller needs the TRUST_TX_LENGTH quirk like
other Fresco controllers, but should not have the BROKEN_MSI quirks set.
BROKEN_MSI quirk causes issues in detecting usb drives connected to docks
with this FL1100 controller.
The BROKEN_MSI flag was apparently accidentally set together with the
TRUST_TX_LENGTH quirk
Original patch went to stable so this should go there as well.
Fixes: ea0f69d821 ("xhci: Enable trust tx length quirk for Fresco FL11 USB controller")
Cc: stable@vger.kernel.org
cc: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211221112825.54690-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7865173cf upstream.
Play a video on the raven (or PCO, raven2) platform, and then do the S3
test. When resume, the following error will be reported:
amdgpu 0000:02:00.0: [drm:amdgpu_ring_test_helper [amdgpu]] *ERROR* ring
vcn_dec test failed (-110)
[drm:amdgpu_device_ip_resume_phase2 [amdgpu]] *ERROR* resume of IP block
<vcn_v1_0> failed -110
amdgpu 0000:02:00.0: amdgpu: amdgpu_device_ip_resume failed (-110).
PM: dpm_run_callback(): pci_pm_resume+0x0/0x90 returns -110
[why]
When playing the video: The power state flag of the vcn block is set to
POWER_STATE_ON.
When doing suspend: There is no change to the power state flag of the
vcn block, it is still POWER_STATE_ON.
When doing resume: Need to open the power gate of the vcn block and set
the power state flag of the VCN block to POWER_STATE_ON.
But at this time, the power state flag of the vcn block is already
POWER_STATE_ON. The power status flag check in the "8f2cdef drm/amd/pm:
avoid duplicate powergate/ungate setting" patch will return the
amdgpu_dpm_set_powergating_by_smu function directly.
As a result, the gate of the power was not opened, causing the
subsequent ring test to fail.
[how]
In the suspend function of the vcn block, explicitly change the power
state flag of the vcn block to POWER_STATE_OFF.
BugLink: https://gitlab.freedesktop.org/drm/amd/-/issues/1828
Signed-off-by: chen gong <curry.gong@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7175f02c4e upstream.
Replace sa_family_t with __kernel_sa_family_t to fix the following
linux/nfc.h userspace compilation errors:
/usr/include/linux/nfc.h:266:2: error: unknown type name 'sa_family_t'
sa_family_t sa_family;
/usr/include/linux/nfc.h:274:2: error: unknown type name 'sa_family_t'
sa_family_t sa_family;
Fixes: 23b7869c0f ("NFC: add the NFC socket raw protocol")
Fixes: d646960f79 ("NFC: Initial LLCP support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 79b69a8370 upstream.
Fix user-space builds if it includes /usr/include/linux/nfc.h before
some of other headers:
/usr/include/linux/nfc.h:281:9: error: unknown type name ‘size_t’
281 | size_t service_name_len;
| ^~~~~~
Fixes: d646960f79 ("NFC: Initial LLCP support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bb436283e2 ]
Wrong user data may cause warning in i2c_transfer(), ex: zero msgs.
Userspace should not be able to trigger warnings, so this patch adds
validation checks for user data in compact ioctl to prevent reported
warnings
Reported-and-tested-by: syzbot+e417648b303855b91d8a@syzkaller.appspotmail.com
Fixes: 7d5cb45655 ("i2c compat ioctls: move to ->compat_ioctl()")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf2b09fedc ]
The reference taken by 'of_find_device_by_node()' must be released when
not needed anymore.
Add the corresponding 'put_device()' in the and error handling paths.
Fixes: 18a6c85fcc ("fsl/fman: Add FMan Port Support")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92a34ab169 ]
As we can see from the comment of the nla_put() that it could return
-EMSGSIZE if the tailroom of the skb is insufficient.
Therefore, it should be better to check the return value of the
nla_put_u32 and return the error code if error accurs.
Also, there are many other functions have the same problem, and if this
patch is correct, I will commit a new version to fix all.
Fixes: 955dc68cb9 ("net/ncsi: Add generic netlink family")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20211229032118.1706294-1-jiasheng@iscas.ac.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c1952aeaa ]
udpgso_bench_tx call setup_sockaddr() for dest address before
parsing all arguments, if we specify "-p ${dst_port}" after "-D ${dst_ip}",
then ${dst_port} will be ignored, and using default cfg_port 8000.
This will cause test case "multiple GRO socks" failed in udpgro.sh.
Setup sockaddr after parsing all arguments.
Fixes: 3a687bef14 ("selftests: udp gso benchmark")
Signed-off-by: Jianguo Wu <wujianguo@chinatelecom.cn>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/ff620d9f-5b52-06ab-5286-44b945453002@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 992d8a4e38 ]
In case of an error in mlx5e_set_features(), 'netdev->features' must be
updated with the correct state of the device to indicate which features
were updated successfully.
To do that we maintain a copy of 'netdev->features' and update it after
successful feature changes, so we can assign it to back to
'netdev->features' if needed.
However, since not all netdev features are handled by the driver (e.g.
GRO/TSO/etc), some features may not be updated correctly in case of an
error updating another feature.
For example, while requesting to disable TSO (feature which is not
handled by the driver) and enable HW-GRO, if an error occurs during
HW-GRO enable, 'oper_features' will be assigned with 'netdev->features'
and HW-GRO turned off. TSO will remain enabled in such case, which is a
bug.
To solve that, instead of using 'netdev->features' as the baseline of
'oper_features' and changing it on set feature success, use 'features'
instead and update it in case of errors.
Fixes: 75b81ce719 ("net/mlx5e: Don't override netdev features field unless in error flow")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 349d43127d ]
A crash occurs when smc_cdc_tx_handler() tries to access smc_sock
but smc_release() has already freed it.
[ 4570.695099] BUG: unable to handle page fault for address: 000000002eae9e88
[ 4570.696048] #PF: supervisor write access in kernel mode
[ 4570.696728] #PF: error_code(0x0002) - not-present page
[ 4570.697401] PGD 0 P4D 0
[ 4570.697716] Oops: 0002 [#1] PREEMPT SMP NOPTI
[ 4570.698228] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.16.0-rc4+ #111
[ 4570.699013] Hardware name: Alibaba Cloud Alibaba Cloud ECS, BIOS 8c24b4c 04/0
[ 4570.699933] RIP: 0010:_raw_spin_lock+0x1a/0x30
<...>
[ 4570.711446] Call Trace:
[ 4570.711746] <IRQ>
[ 4570.711992] smc_cdc_tx_handler+0x41/0xc0
[ 4570.712470] smc_wr_tx_tasklet_fn+0x213/0x560
[ 4570.712981] ? smc_cdc_tx_dismisser+0x10/0x10
[ 4570.713489] tasklet_action_common.isra.17+0x66/0x140
[ 4570.714083] __do_softirq+0x123/0x2f4
[ 4570.714521] irq_exit_rcu+0xc4/0xf0
[ 4570.714934] common_interrupt+0xba/0xe0
Though smc_cdc_tx_handler() checked the existence of smc connection,
smc_release() may have already dismissed and released the smc socket
before smc_cdc_tx_handler() further visits it.
smc_cdc_tx_handler() |smc_release()
if (!conn) |
|
|smc_cdc_tx_dismiss_slots()
| smc_cdc_tx_dismisser()
|
|sock_put(&smc->sk) <- last sock_put,
| smc_sock freed
bh_lock_sock(&smc->sk) (panic) |
To make sure we won't receive any CDC messages after we free the
smc_sock, add a refcount on the smc_connection for inflight CDC
message(posted to the QP but haven't received related CQE), and
don't release the smc_connection until all the inflight CDC messages
haven been done, for both success or failed ones.
Using refcount on CDC messages brings another problem: when the link
is going to be destroyed, smcr_link_clear() will reset the QP, which
then remove all the pending CQEs related to the QP in the CQ. To make
sure all the CQEs will always come back so the refcount on the
smc_connection can always reach 0, smc_ib_modify_qp_reset() was replaced
by smc_ib_modify_qp_error().
And remove the timeout in smc_wr_tx_wait_no_pending_sends() since we
need to wait for all pending WQEs done, or we may encounter use-after-
free when handling CQEs.
For IB device removal routine, we need to wait for all the QPs on that
device been destroyed before we can destroy CQs on the device, or
the refcount on smc_connection won't reach 0 and smc_sock cannot be
released.
Fixes: 5f08318f61 ("smc: connection data control (CDC)")
Reported-by: Wen Gu <guwen@linux.alibaba.com>
Signed-off-by: Dust Li <dust.li@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90cee52f2e ]
We found smc_llc_send_link_delete_all() sometimes wait
for 2s timeout when testing with RDMA link up/down.
It is possible when a smc_link is in ACTIVATING state,
the underlaying QP is still in RESET or RTR state, which
cannot send any messages out.
smc_llc_send_link_delete_all() use smc_link_usable() to
checks whether the link is usable, if the QP is still in
RESET or RTR state, but the smc_link is in ACTIVATING, this
LLC message will always fail without any CQE entering the
CQ, and we will always wait 2s before timeout.
Since we cannot send any messages through the QP before
the QP enter RTS. I add a wrapper smc_link_sendable()
which checks the state of QP along with the link state.
And replace smc_link_usable() with smc_link_sendable()
in all LLC & CDC message sending routine.
Fixes: 5f08318f61 ("smc: connection data control (CDC)")
Signed-off-by: Dust Li <dust.li@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95f7f3e7dc ]
Commit 8f3d65c166 ("net/smc: fix wait on already cleared link")
introduced link refcounting to avoid waits on already cleared links.
This patch extents and improves the refcounting to cover all
remaining possible cases for this kind of error situation.
Fixes: 15e1b99aad ("net/smc: no WR buffer wait for terminating link group")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5be60a9453 ]
Received frames have FCS truncated. There is no need
to subtract FCS length from the statistics.
Fixes: fe1a56420c ("net: lantiq: Add Lantiq / Intel VRX200 Ethernet driver")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1cd5384c88 ]
'ndev' is a managed resource allocated with devm_alloc_etherdev(), so there
is no need to call free_netdev() explicitly or there will be a double
free().
Simplify all error handling paths accordingly.
Fixes: d51b6ce441 ("net: ethernet: add ag71xx driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca506fca46 ]
The D-Link DSB-650TX (2001:4002) is unable to receive Ethernet frames
that are longer than 1518 octets, for example, Ethernet frames that
contain 802.1Q VLAN tags.
The frames are sent to the pegasus driver via USB but the driver
discards them because they have the Long_pkt field set to 1 in the
received status report. The function read_bulk_callback of the pegasus
driver treats such received "packets" (in the terminology of the
hardware) as errors but the field simply does just indicate that the
Ethernet frame (MAC destination to FCS) is longer than 1518 octets.
It seems that in the 1990s there was a distinction between
"giant" (> 1518) and "runt" (< 64) frames and the hardware includes
flags to indicate this distinction. It seems that the purpose of the
distinction "giant" frames was to not allow infinitely long frames due
to transmission errors and to allow hardware to have an upper limit of
the frame size. However, the hardware already has such limit with its
2048 octet receive buffer and, therefore, Long_pkt is merely a
convention and should not be treated as a receive error.
Actually, the hardware is even able to receive Ethernet frames with 2048
octets which exceeds the claimed limit frame size limit of the driver of
1536 octets (PEGASUS_MTU).
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Matthias-Christian Ott <ott@mirix.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d7373dabf ]
In smc_wr_tx_send_wait() the completion on index specified by
pend->idx is initialized and after smc_wr_tx_send() was called the wait
for completion starts. pend->idx is used to get the correct index for
the wait, but the pend structure could already be cleared in
smc_wr_tx_process_cqe().
Introduce pnd_idx to hold and use a local copy of the correct index.
Fixes: 09c61d24f9 ("net/smc: wait for departure of an IB message")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ec7d18d18 ]
This patch is to delay the endpoint free by calling call_rcu() to fix
another use-after-free issue in sctp_sock_dump():
BUG: KASAN: use-after-free in __lock_acquire+0x36d9/0x4c20
Call Trace:
__lock_acquire+0x36d9/0x4c20 kernel/locking/lockdep.c:3218
lock_acquire+0x1ed/0x520 kernel/locking/lockdep.c:3844
__raw_spin_lock_bh include/linux/spinlock_api_smp.h:135 [inline]
_raw_spin_lock_bh+0x31/0x40 kernel/locking/spinlock.c:168
spin_lock_bh include/linux/spinlock.h:334 [inline]
__lock_sock+0x203/0x350 net/core/sock.c:2253
lock_sock_nested+0xfe/0x120 net/core/sock.c:2774
lock_sock include/net/sock.h:1492 [inline]
sctp_sock_dump+0x122/0xb20 net/sctp/diag.c:324
sctp_for_each_transport+0x2b5/0x370 net/sctp/socket.c:5091
sctp_diag_dump+0x3ac/0x660 net/sctp/diag.c:527
__inet_diag_dump+0xa8/0x140 net/ipv4/inet_diag.c:1049
inet_diag_dump+0x9b/0x110 net/ipv4/inet_diag.c:1065
netlink_dump+0x606/0x1080 net/netlink/af_netlink.c:2244
__netlink_dump_start+0x59a/0x7c0 net/netlink/af_netlink.c:2352
netlink_dump_start include/linux/netlink.h:216 [inline]
inet_diag_handler_cmd+0x2ce/0x3f0 net/ipv4/inet_diag.c:1170
__sock_diag_cmd net/core/sock_diag.c:232 [inline]
sock_diag_rcv_msg+0x31d/0x410 net/core/sock_diag.c:263
netlink_rcv_skb+0x172/0x440 net/netlink/af_netlink.c:2477
sock_diag_rcv+0x2a/0x40 net/core/sock_diag.c:274
This issue occurs when asoc is peeled off and the old sk is freed after
getting it by asoc->base.sk and before calling lock_sock(sk).
To prevent the sk free, as a holder of the sk, ep should be alive when
calling lock_sock(). This patch uses call_rcu() and moves sock_put and
ep free into sctp_endpoint_destroy_rcu(), so that it's safe to try to
hold the ep under rcu_read_lock in sctp_transport_traverse_process().
If sctp_endpoint_hold() returns true, it means this ep is still alive
and we have held it and can continue to dump it; If it returns false,
it means this ep is dead and can be freed after rcu_read_unlock, and
we should skip it.
In sctp_sock_dump(), after locking the sk, if this ep is different from
tsp->asoc->ep, it means during this dumping, this asoc was peeled off
before calling lock_sock(), and the sk should be skipped; If this ep is
the same with tsp->asoc->ep, it means no peeloff happens on this asoc,
and due to lock_sock, no peeloff will happen either until release_sock.
Note that delaying endpoint free won't delay the port release, as the
port release happens in sctp_endpoint_destroy() before calling call_rcu().
Also, freeing endpoint by call_rcu() makes it safe to access the sk by
asoc->base.sk in sctp_assocs_seq_show() and sctp_rcv().
Thanks Jones to bring this issue up.
v1->v2:
- improve the changelog.
- add kfree(ep) into sctp_endpoint_destroy_rcu(), as Jakub noticed.
Reported-by: syzbot+9276d76e83e3bcde6c99@syzkaller.appspotmail.com
Reported-by: Lee Jones <lee.jones@linaro.org>
Fixes: d25adbeb0c ("sctp: fix an use-after-free issue in sctp_sock_dump")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5471d5226c ]
The below referenced commit correctly updated the computation of number
of segments (gso_size) by using only the gso payload size and
removing the header lengths.
With this change the regression test started failing. Update
the tests to match this new behavior.
Both IPv4 and IPv6 tests are updated, as a separate patch in this series
will update udp_v6_send_skb to match this change in udp_send_skb.
Fixes: 158390e456 ("udp: using datalen to cap max gso segments")
Signed-off-by: Coco Li <lixiaoyan@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20211223222441.2975883-2-lixiaoyan@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 736ef37fd9 ]
The max number of UDP gso segments is intended to cap to
UDP_MAX_SEGMENTS, this is checked in udp_send_skb().
skb->len contains network and transport header len here, we should use
only data len instead.
This is the ipv6 counterpart to the below referenced commit,
which missed the ipv6 change
Fixes: 158390e456 ("udp: using datalen to cap max gso segments")
Signed-off-by: Coco Li <lixiaoyan@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20211223222441.2975883-1-lixiaoyan@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19c4aba2d4 ]
There are two ICOSQs per channel: one is needed for RX, and the other
for async operations (XSK TX, kTLS offload). Currently, the recovery
flow for both is the same, and async ICOSQ is mistakenly treated like
the regular ICOSQ.
This patch prevents running the regular ICOSQ recovery on async ICOSQ.
The purpose of async ICOSQ is to handle XSK wakeup requests and post
kTLS offload RX parameters, it has nothing to do with RQ and XSKRQ UMRs,
so the regular recovery sequence is not applicable here.
Fixes: be5323c837 ("net/mlx5e: Report and recover from CQE error on ICOSQ")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 732bc2ff08 upstream.
Clang static analysis reports this warning
hooks.c:5765:6: warning: 4th function call argument is an uninitialized
value
if (selinux_xfrm_postroute_last(sksec->sid, skb, &ad, proto))
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
selinux_parse_skb() can return ok without setting proto. The later call
to selinux_xfrm_postroute_last() does an early check of proto and can
return ok if the garbage proto value matches. So initialize proto.
Cc: stable@vger.kernel.org
Fixes: eef9b41622 ("selinux: cleanup selinux_xfrm_sock_rcv_skb() and selinux_xfrm_postroute_last()")
Signed-off-by: Tom Rix <trix@redhat.com>
[PM: typo/spelling and checkpatch.pl description fixes]
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4eb1782eaa upstream.
Commit 85bf17b28f ("recordmcount.pl: look for jgnop instruction as well
as bcrl on s390") added a new alternative mnemonic for the existing brcl
instruction. This is required for the combination old gcc version (pre 9.0)
and binutils since version 2.37.
However at the same time this commit introduced a typo, replacing brcl with
bcrl. As a result no mcount locations are detected anymore with old gcc
versions (pre 9.0) and binutils before version 2.37.
Fix this by using the correct mnemonic again.
Reported-by: Miroslav Benes <mbenes@suse.cz>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: <stable@vger.kernel.org>
Fixes: 85bf17b28f ("recordmcount.pl: look for jgnop instruction as well as bcrl on s390")
Link: https://lore.kernel.org/r/alpine.LSU.2.21.2112230949520.19849@pobox.suse.cz
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d7f55471db ]
Fix modpost Section mismatch error in memblock_phys_alloc()
[...]
WARNING: modpost: vmlinux.o(.text.unlikely+0x1dcc): Section mismatch in reference
from the function memblock_phys_alloc() to the function .init.text:memblock_phys_alloc_range()
The function memblock_phys_alloc() references
the function __init memblock_phys_alloc_range().
This is often because memblock_phys_alloc lacks a __init
annotation or the annotation of memblock_phys_alloc_range is wrong.
ERROR: modpost: Section mismatches detected.
Set CONFIG_SECTION_MISMATCH_WARN_ONLY=y to allow them.
[...]
memblock_phys_alloc() is a one-line wrapper, make it __always_inline to
avoid these section mismatches.
Reported-by: k2ci <kernel-bot@kylinos.cn>
Suggested-by: Mike Rapoport <rppt@kernel.org>
Signed-off-by: Jackie Liu <liuyun01@kylinos.cn>
[rppt: slightly massaged changelog ]
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Link: https://lore.kernel.org/r/20211217020754.2874872-1-liu.yun@linux.dev
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 484730e586 ]
When a trap 7 (Instruction access rights) occurs, this means the CPU
couldn't execute an instruction due to missing execute permissions on
the memory region. In this case it seems the CPU didn't even fetched
the instruction from memory and thus did not store it in the cr19 (IIR)
register before calling the trap handler. So, the trap handler will find
some random old stale value in cr19.
This patch simply overwrites the stale IIR value with a constant magic
"bad food" value (0xbaadf00d), in the hope people don't start to try to
understand the various random IIR values in trap 7 dumps.
Noticed-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f702e11076 ]
hwight16() is much faster. While we are at it, no need to include
"perm =" part into data_race() macro, for perm is a local variable
that cannot be accessed by other threads.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04e57a2d95 ]
If tomoyo is used in a testing/fuzzing environment in learning mode,
for lots of domains the quota will be exceeded and stay exceeded
for prolonged periods of time. In such cases it's pointless (and slow)
to walk the whole acl list again and again just to rediscover that
the quota is exceeded. We already have the TOMOYO_DIF_QUOTA_WARNED flag
that notes the overflow condition. Check it early to avoid the slowdown.
[penguin-kernel]
This patch causes a user visible change that the learning mode will not be
automatically resumed after the quota is increased. To resume the learning
mode, administrator will need to explicitly clear TOMOYO_DIF_QUOTA_WARNED
flag after increasing the quota. But I think that this change is generally
preferable, for administrator likely wants to optimize the acl list for
that domain before increasing the quota, or that domain likely hits the
quota again. Therefore, don't try to care to clear TOMOYO_DIF_QUOTA_WARNED
flag automatically when the quota for that domain changed.
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9222ba68c3 ]
We've got a bug report about the non-working keyboard on ASUS ZenBook
UX425UA. It seems that the PS/2 device isn't ready immediately at
boot but takes some seconds to get ready. Until now, the only
workaround is to defer the probe, but it's available only when the
driver is a module. However, many distros, including openSUSE as in
the original report, build the PS/2 input drivers into kernel, hence
it won't work easily.
This patch adds the support for the deferred probe for i8042 stuff as
a workaround of the problem above. When the deferred probe mode is
enabled and the device couldn't be probed, it'll be repeated with the
standard deferred probe mechanism.
The deferred probe mode is enabled either via the new option
i8042.probe_defer or via the quirk table entry. As of this patch, the
quirk table contains only ASUS ZenBook UX425UA.
The deferred probe part is based on Fabio's initial work.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1190256
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Samuel Čavoj <samuel@cavoj.net>
Link: https://lore.kernel.org/r/20211117063757.11380-1-tiwai@suse.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
The drm edid parser doesn't signal RGB support on DVI monitors
with old edid versions, leading to 8-bit RGB mode being rejected
and no video on DVI monitors.
As 8-bit RGB is mandatory on HDMI and DVI monitors anyways we can
simply drop the RGB format check, aligning vc4 with other drivers.
Signed-off-by: Matthias Reichl <hias@horus.com>
When vc4_hdmi_connector_detect() was called in
connector_status_connected state it incorrectly cleared the
hdmi_monitor flag, leading to no audio on RPi3.
Fix this by clearing hdmi_monitor only when the hpd check
indicated no connection or if reading the edid failed.
Signed-off-by: Matthias Reichl <hias@horus.com>
commit 75a2f31520 upstream.
This ioctl() implicitly assumed that the socket was already bound to
a valid local socket name, i.e. Phonet object. If the socket was not
bound, two separate problems would occur:
1) We'd send an pipe enablement request with an invalid source object.
2) Later socket calls could BUG on the socket unexpectedly being
connected yet not bound to a valid object.
Reported-by: syzbot+2dc91e7fc3dea88b1e8a@syzkaller.appspotmail.com
Signed-off-by: Rémi Denis-Courmont <remi@remlab.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2f37aead1 upstream.
The previous commit 3e0588c291 ("hamradio: defer ax25 kfree after
unregister_netdev") reorder the kfree operations and unregister_netdev
operation to prevent UAF.
This commit improves the previous one by also deferring the nullify of
the ax->tty pointer. Otherwise, a NULL pointer dereference bug occurs.
Partial of the stack trace is shown below.
BUG: kernel NULL pointer dereference, address: 0000000000000538
RIP: 0010:ax_xmit+0x1f9/0x400
...
Call Trace:
dev_hard_start_xmit+0xec/0x320
sch_direct_xmit+0xea/0x240
__qdisc_run+0x166/0x5c0
__dev_queue_xmit+0x2c7/0xaf0
ax25_std_establish_data_link+0x59/0x60
ax25_connect+0x3a0/0x500
? security_socket_connect+0x2b/0x40
__sys_connect+0x96/0xc0
? __hrtimer_init+0xc0/0xc0
? common_nsleep+0x2e/0x50
? switch_fpu_return+0x139/0x1a0
__x64_sys_connect+0x11/0x20
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xa9
The crash point is shown as below
static void ax_encaps(...) {
...
set_bit(TTY_DO_WRITE_WAKEUP, &ax->tty->flags); // ax->tty = NULL!
...
}
By placing the nullify action after the unregister_netdev, the ax->tty
pointer won't be assigned as NULL net_device framework layer is well
synchronized.
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e0588c291 upstream.
There is a possible race condition (use-after-free) like below
(USE) | (FREE)
ax25_sendmsg |
ax25_queue_xmit |
dev_queue_xmit |
__dev_queue_xmit |
__dev_xmit_skb |
sch_direct_xmit | ...
xmit_one |
netdev_start_xmit | tty_ldisc_kill
__netdev_start_xmit | mkiss_close
ax_xmit | kfree
ax_encaps |
|
Even though there are two synchronization primitives before the kfree:
1. wait_for_completion(&ax->dead). This can prevent the race with
routines from mkiss_ioctl. However, it cannot stop the routine coming
from upper layer, i.e., the ax25_sendmsg.
2. netif_stop_queue(ax->dev). It seems that this line of code aims to
halt the transmit queue but it fails to stop the routine that already
being xmit.
This patch reorder the kfree after the unregister_netdev to avoid the
possible UAF as the unregister_netdev() is well synchronized and won't
return if there is a running routine.
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ade48d0c2 upstream.
The existing cleanup routine implementation is not well synchronized
with the syscall routine. When a device is detaching, below race could
occur.
static int ax25_sendmsg(...) {
...
lock_sock()
ax25 = sk_to_ax25(sk);
if (ax25->ax25_dev == NULL) // CHECK
...
ax25_queue_xmit(skb, ax25->ax25_dev->dev); // USE
...
}
static void ax25_kill_by_device(...) {
...
if (s->ax25_dev == ax25_dev) {
s->ax25_dev = NULL;
...
}
Other syscall functions like ax25_getsockopt, ax25_getname,
ax25_info_show also suffer from similar races. To fix them, this patch
introduce lock_sock() into ax25_kill_by_device in order to guarantee
that the nullify action in cleanup routine cannot proceed when another
socket request is pending.
Signed-off-by: Hanjie Wu <nagi@zju.edu.cn>
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cdc5287aca upstream.
Bit 7 of the status register indicates that the chip is busy
doing a conversion. It does not indicate an alarm status.
Stop reporting it as alarm status bit.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da7dc05684 upstream.
Tests with a real chip and a closer look into the datasheet reveals
that the local and remote critical alarm status bits are swapped for
MAX6680/MAX6681.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ff29701ff upstream.
Update the documentation for kvm-intel's emulate_invalid_guest_state to
rectify the description of KVM's default behavior, and to document that
the behavior and thus parameter only applies to L1.
Fixes: a27685c33a ("KVM: VMX: Emulate invalid guest state by default")
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211207193006.120997-4-seanjc@google.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 890d5b4090 upstream.
When listening for notifications through netlink of a new interface being
registered, sporadically, it is possible for the MAC to be read as zero.
The zero MAC address lasts a short period of time and then switches to a
valid random MAC address.
This causes problems for netd in Android, which assumes that the interface
is malfunctioning and will not use it.
In the good case we get this log:
InterfaceController::getCfg() ifName usb0
hwAddr 92:a8:f0:73:79:5b ipv4Addr 0.0.0.0 flags 0x1002
In the error case we get these logs:
InterfaceController::getCfg() ifName usb0
hwAddr 00:00:00:00:00:00 ipv4Addr 0.0.0.0 flags 0x1002
netd : interfaceGetCfg("usb0")
netd : interfaceSetCfg() -> ServiceSpecificException
(99, "[Cannot assign requested address] : ioctl() failed")
The reason for the issue is the order in which the interface is setup,
it is first registered through register_netdev() and after the MAC
address is set.
Fixed by first setting the MAC address of the net_device and after that
calling register_netdev().
Fixes: bcd4a1c40b ("usb: gadget: u_ether: construct with default values and add setters/getters")
Cc: stable@vger.kernel.org
Signed-off-by: Marian Postevca <posteuca@mutex.one>
Link: https://lore.kernel.org/r/20211204214912.17627-1-posteuca@mutex.one
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd84bfdddd upstream.
Ceph always inherits the SGID bit if it is set on the parent inode,
while the generic inode_init_owner does not do this in a few cases where
it can create a possible security problem (cf. [1]).
Update ceph to strip the SGID bit just as inode_init_owner would.
This bug was detected by the mapped mount testsuite in [3]. The
testsuite tests all core VFS functionality and semantics with and
without mapped mounts. That is to say it functions as a generic VFS
testsuite in addition to a mapped mount testsuite. While working on
mapped mount support for ceph, SIGD inheritance was the only failing
test for ceph after the port.
The same bug was detected by the mapped mount testsuite in XFS in
January 2021 (cf. [2]).
[1]: commit 0fa3ecd878 ("Fix up non-directory creation in SGID directories")
[2]: commit 01ea173e10 ("xfs: fix up non-directory creation in SGID directories")
[3]: https://git.kernel.org/fs/xfs/xfstests-dev.git
Cc: stable@vger.kernel.org
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5598b24efaf4892741c798b425d543e4bed357a1 upstream.
As Wenqing Liu reported in bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=215235
- Overview
page fault in f2fs_setxattr() when mount and operate on corrupted image
- Reproduce
tested on kernel 5.16-rc3, 5.15.X under root
1. unzip tmp7.zip
2. ./single.sh f2fs 7
Sometimes need to run the script several times
- Kernel dump
loop0: detected capacity change from 0 to 131072
F2FS-fs (loop0): Found nat_bits in checkpoint
F2FS-fs (loop0): Mounted with checkpoint version = 7548c2ee
BUG: unable to handle page fault for address: ffffe47bc7123f48
RIP: 0010:kfree+0x66/0x320
Call Trace:
__f2fs_setxattr+0x2aa/0xc00 [f2fs]
f2fs_setxattr+0xfa/0x480 [f2fs]
__f2fs_set_acl+0x19b/0x330 [f2fs]
__vfs_removexattr+0x52/0x70
__vfs_removexattr_locked+0xb1/0x140
vfs_removexattr+0x56/0x100
removexattr+0x57/0x80
path_removexattr+0xa3/0xc0
__x64_sys_removexattr+0x17/0x20
do_syscall_64+0x37/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
The root cause is in __f2fs_setxattr(), we missed to do sanity check on
last xattr entry, result in out-of-bound memory access during updating
inconsistent xattr data of target inode.
After the fix, it can detect such xattr inconsistency as below:
F2FS-fs (loop11): inode (7) has invalid last xattr entry, entry_size: 60676
F2FS-fs (loop11): inode (8) has corrupted xattr
F2FS-fs (loop11): inode (8) has corrupted xattr
F2FS-fs (loop11): inode (8) has invalid last xattr entry, entry_size: 47736
Cc: stable@vger.kernel.org
Reported-by: Wenqing Liu <wenqingliu0120@gmail.com>
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 18549bf4b2 upstream.
Pointer to the allocated pages (struct page *page) has already
progressed towards the end of allocation. It is incorrect to perform
__free_pages(page, order) using this pointer as we would free any
arbitrary pages. Fix this by stop modifying the page pointer.
Fixes: ec185dd3ab ("optee: Fix memory leak when failing to register shm pages")
Cc: stable@vger.kernel.org
Reported-by: Patrik Lantz <patrik.lantz@axis.com>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a57d83c78 upstream.
Hulk Robot reported a panic in put_page_testzero() when testing
madvise() with MADV_SOFT_OFFLINE. The BUG() is triggered when retrying
get_any_page(). This is because we keep MF_COUNT_INCREASED flag in
second try but the refcnt is not increased.
page dumped because: VM_BUG_ON_PAGE(page_ref_count(page) == 0)
------------[ cut here ]------------
kernel BUG at include/linux/mm.h:737!
invalid opcode: 0000 [#1] PREEMPT SMP
CPU: 5 PID: 2135 Comm: sshd Tainted: G B 5.16.0-rc6-dirty #373
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014
RIP: release_pages+0x53f/0x840
Call Trace:
free_pages_and_swap_cache+0x64/0x80
tlb_flush_mmu+0x6f/0x220
unmap_page_range+0xe6c/0x12c0
unmap_single_vma+0x90/0x170
unmap_vmas+0xc4/0x180
exit_mmap+0xde/0x3a0
mmput+0xa3/0x250
do_exit+0x564/0x1470
do_group_exit+0x3b/0x100
__do_sys_exit_group+0x13/0x20
__x64_sys_exit_group+0x16/0x20
do_syscall_64+0x34/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
Modules linked in:
---[ end trace e99579b570fe0649 ]---
RIP: 0010:release_pages+0x53f/0x840
Link: https://lkml.kernel.org/r/20211221074908.3910286-1-liushixin2@huawei.com
Fixes: b94e02822d ("mm,hwpoison: try to narrow window race for free pages")
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Acked-by: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8536a5ef88 upstream.
The Thumb2 version of the FP exception handling entry code treats the
register holding the CP number (R8) differently, resulting in the iWMMXT
CP number check to be incorrect.
Fix this by unifying the ARM and Thumb2 code paths, and switch the
order of the additions of the TI_USED_CP offset and the shifted CP
index.
Cc: <stable@vger.kernel.org>
Fixes: b86040a59f ("Thumb-2: Implementation of the unified start-up and exceptions code")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f89b548ca6 upstream.
The vendor driver implements special handling for multi-block
SD_IO_RW_EXTENDED (and SD_IO_RW_DIRECT) commands which have data
attached to them. It sets the MANUAL_STOP bit in the MESON_SDHC_MISC
register for these commands. In all other cases this bit is cleared.
Here we omit SD_IO_RW_DIRECT since that command never has any data
attached to it.
This fixes SDIO wifi using the brcmfmac driver which reported the
following error without this change on a Netxeon S82 board using a
Meson8 (S802) SoC:
brcmf_fw_alloc_request: using brcm/brcmfmac43362-sdio for chip
BCM43362/1
brcmf_sdiod_ramrw: membytes transfer failed
brcmf_sdio_download_code_file: error -110 on writing 219557 membytes
at 0x00000000
brcmf_sdio_download_firmware: dongle image file download failed
And with this change:
brcmf_fw_alloc_request: using brcm/brcmfmac43362-sdio for chip
BCM43362/1
brcmf_c_process_clm_blob: no clm_blob available (err=-2), device may
have limited channels available
brcmf_c_preinit_dcmds: Firmware: BCM43362/1 wl0: Apr 22 2013 14:50:00
version 5.90.195.89.6 FWID 01-b30a427d
Fixes: e4bf1b0970 ("mmc: host: meson-mx-sdhc: new driver for the Amlogic Meson SDHC host")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211219153442.463863-2-martin.blumenstingl@googlemail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a5875f14b upstream.
When replugging the device the following message shows up:
gpio gpiochip2: (dln2): detected irqchip that is shared with multiple gpiochips: please fix the driver.
This also has the effect that interrupts won't work.
The same problem would also show up if multiple devices where plugged in.
Fix this by allocating the irq_chip data structure per instance like other
drivers do.
I don't know when this problem appeared, but it is present in 5.10.
Cc: <stable@vger.kernel.org> # 5.10+
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fdba608f15 upstream.
Drop a check that guards triggering a posted interrupt on the currently
running vCPU, and more importantly guards waking the target vCPU if
triggering a posted interrupt fails because the vCPU isn't IN_GUEST_MODE.
If a vIRQ is delivered from asynchronous context, the target vCPU can be
the currently running vCPU and can also be blocking, in which case
skipping kvm_vcpu_wake_up() is effectively dropping what is supposed to
be a wake event for the vCPU.
The "do nothing" logic when "vcpu == running_vcpu" mostly works only
because the majority of calls to ->deliver_posted_interrupt(), especially
when using posted interrupts, come from synchronous KVM context. But if
a device is exposed to the guest using vfio-pci passthrough, the VFIO IRQ
and vCPU are bound to the same pCPU, and the IRQ is _not_ configured to
use posted interrupts, wake events from the device will be delivered to
KVM from IRQ context, e.g.
vfio_msihandler()
|
|-> eventfd_signal()
|
|-> ...
|
|-> irqfd_wakeup()
|
|->kvm_arch_set_irq_inatomic()
|
|-> kvm_irq_delivery_to_apic_fast()
|
|-> kvm_apic_set_irq()
This also aligns the non-nested and nested usage of triggering posted
interrupts, and will allow for additional cleanups.
Fixes: 379a3c8ee4 ("KVM: VMX: Optimize posted-interrupt delivery for timer fastpath")
Cc: stable@vger.kernel.org
Reported-by: Longpeng (Mike) <longpeng2@huawei.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20211208015236.1616697-18-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 57690554ab upstream.
Both __pkru_allows_write() and arch_set_user_pkey_access() shift
PKRU_WD_BIT (a signed constant) by up to 30 bits, hitting the
sign bit.
Use unsigned constants instead.
Clearly pkey 15 has not been used in combination with UBSAN yet.
Noticed by code inspection only. I can't actually provoke the
compiler into generating incorrect logic as far as this shift is
concerned.
[
dhansen: add stable@ tag, plus minor changelog massaging,
For anyone doing backports, these #defines were in
arch/x86/include/asm/pgtable.h before 784a46618f.
]
Fixes: 33a709b25a ("mm/gup, x86/mm/pkeys: Check VMAs and PTEs for protection keys")
Signed-off-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20211216000856.4480-1-andrew.cooper3@citrix.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dfd0743f1d upstream.
Since the tee subsystem does not keep a strong reference to its idle
shared memory buffers, it races with other threads that try to destroy a
shared memory through a close of its dma-buf fd or by unmapping the
memory.
In tee_shm_get_from_id() when a lookup in teedev->idr has been
successful, it is possible that the tee_shm is in the dma-buf teardown
path, but that path is blocked by the teedev mutex. Since we don't have
an API to tell if the tee_shm is in the dma-buf teardown path or not we
must find another way of detecting this condition.
Fix this by doing the reference counting directly on the tee_shm using a
new refcount_t refcount field. dma-buf is replaced by using
anon_inode_getfd() instead, this separates the life-cycle of the
underlying file from the tee_shm. tee_shm_put() is updated to hold the
mutex when decreasing the refcount to 0 and then remove the tee_shm from
teedev->idr before releasing the mutex. This means that the tee_shm can
never be found unless it has a refcount larger than 0.
Fixes: 967c9cca2c ("tee: generic TEE subsystem")
Cc: stable@vger.kernel.org
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Lars Persson <larper@axis.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Reported-by: Patrik Lantz <patrik.lantz@axis.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3a5a68cff upstream.
The address bits used to select the futex spinlock need to match those used in
the LWS code in syscall.S. The mask 0x3f8 only selects 7 bits. It should
select 8 bits.
This change fixes the glibc nptl/tst-cond24 and nptl/tst-cond25 tests.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Fixes: 53a42b6324 ("parisc: Switch to more fine grained lws locks")
Cc: stable@vger.kernel.org # 5.10+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f66fce0f4 upstream.
The completer in the "or,ev %r1,%r30,%r30" instruction is reversed, so we are
not clipping the LWS number when we are called from a 32-bit process (W=0).
We need to nulify the following depdi instruction when the least-significant
bit of %r30 is 1.
If the %r20 register is not clipped, a user process could perform a LWS call
that would branch to an undefined location in the kernel and potentially crash
the machine.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # 4.19+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 34f35f8f14 upstream.
During probe ssif_info->client is dereferenced in error path. However,
it is set when some of the error checking has already been done. This
causes following kernel crash if an error path is taken:
[ 30.645593][ T674] ipmi_ssif 0-000e: ipmi_ssif: Not probing, Interface already present
[ 30.657616][ T674] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000088
...
[ 30.657723][ T674] pc : __dev_printk+0x28/0xa0
[ 30.657732][ T674] lr : _dev_err+0x7c/0xa0
...
[ 30.657772][ T674] Call trace:
[ 30.657775][ T674] __dev_printk+0x28/0xa0
[ 30.657778][ T674] _dev_err+0x7c/0xa0
[ 30.657781][ T674] ssif_probe+0x548/0x900 [ipmi_ssif 62ce4b08badc1458fd896206d9ef69a3c31f3d3e]
[ 30.657791][ T674] i2c_device_probe+0x37c/0x3c0
...
Initialize ssif_info->client before any error path can be taken. Clear
i2c_client data in the error path to prevent the dangling pointer from
leaking.
Fixes: c4436c9149 ("ipmi_ssif: avoid registering duplicate ssif interface")
Cc: stable@vger.kernel.org # 5.4.x
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Message-Id: <20211208093239.4432-1-ykaukab@suse.de>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee907afb0c upstream.
The out-of-tree vendor driver uses the following approach to set the
AIU_I2S_MISC register:
1) write AIU_MEM_I2S_START_PTR and AIU_MEM_I2S_RD_PTR
2) configure AIU_I2S_MUTE_SWAP[15:0]
3) write AIU_MEM_I2S_END_PTR
4) set AIU_I2S_MISC[2] to 1 (documented as: "put I2S interface in hold
mode")
5) set AIU_I2S_MISC[4] to 1 (depending on the driver revision it always
stays at 1 while for older drivers this bit is unset in step 4)
6) set AIU_I2S_MISC[2] to 0
7) write AIU_MEM_I2S_MASKS
8) toggle AIU_MEM_I2S_CONTROL[0]
9) toggle AIU_MEM_I2S_BUF_CNTL[0]
Move setting the AIU_I2S_MISC[2] bit to aiu_fifo_i2s_hw_params() so it
resembles the flow in the vendor kernel more closely. While here also
configure AIU_I2S_MISC[4] (documented as: "force each audio data to
left or right according to the bit attached with the audio data")
similar to how the vendor driver does this. This fixes the infamous and
long-standing "machine gun noise" issue (a buffer underrun issue).
Fixes: 6ae9ca9ce9 ("ASoC: meson: aiu: add i2s and spdif support")
Reported-by: Christian Hewitt <christianshewitt@gmail.com>
Reported-by: Geraldo Nascimento <geraldogabriel@gmail.com>
Tested-by: Christian Hewitt <christianshewitt@gmail.com>
Tested-by: Geraldo Nascimento <geraldogabriel@gmail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Cc: stable@vger.kernel.org
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20211206210804.2512999-3-martin.blumenstingl@googlemail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit edca7cc4b0 upstream.
The Clevo NJ51CU comes either with the ALC293 or the ALC256 codec, but uses
the 0x8686 subproduct id in both cases. The ALC256 codec needs a different
quirk for the headset microphone working and and edditional quirk for sound
working after suspend and resume.
When waking up from s3 suspend the Coef 0x10 is set to 0x0220 instead of
0x0020 on the ALC256 codec. Setting the value manually makes the sound
work again. This patch does this automatically.
[ minor coding style fix by tiwai ]
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Fixes: b5acfe152a ("ALSA: hda/realtek: Add some Clove SSID in the ALC293(ALC1220)")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211215191646.844644-1-wse@tuxedocomputers.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2dee54b289 upstream.
Static analysis with scan-build has found an assignment to vp2 that is
never used. It seems that the check on vp->state > 0 should be actually
on vp2->state instead. Fix this.
This dates back to 2002, I found the offending commit from the git
history git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git,
commit 91e39521bbf6 ("[PATCH] ALSA patch for 2.5.4")
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211212172025.470367-1-colin.i.king@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 16ba51b5dc ]
Tests with a real chip and a closer look into the datasheet show that
MAX6654 does not support CRIT/THERM/OVERTEMP limits, so drop support
of the respective attributes for this chip.
Introduce LM90_HAVE_CRIT flag and use it to instantiate critical limit
attributes to solve the problem.
Cc: Josh Lehan <krellan@google.com>
Fixes: 229d495d81 ("hwmon: (lm90) Add max6654 support to lm90 driver")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f347e249fc ]
A flag indicating extended temperature support makes it easier
to add support for additional chips with this functionality.
Cc: David T. Wilson <david.wilson@nasa.gov>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8344f7693 ]
TMP461 is almost identical to TMP451 and was actually detected as TMP451
with the existing lm90 driver if its I2C address is 0x4c. Add support
for it to the lm90 driver. At the same time, improve the chip detection
function to at least try to distinguish between TMP451 and TMP461.
As a side effect, this fixes commit 24333ac26d ("hwmon: (tmp401) use
smb word operations instead of 2 smb byte operations"). TMP461 does not
support word operations on temperature registers, which causes bad
temperature readings with the tmp401 driver. The lm90 driver does not
perform word operations on temperature registers and thus does not have
this problem.
Support is listed as basic because TMP461 supports a sensor resolution
of 0.0625 degrees C, while the lm90 driver assumes a resolution of 0.125
degrees C. Also, the TMP461 supports negative temperatures with its
default temperature range, which is not the case for similar chips
supported by the lm90 and the tmp401 drivers. Those limitations will be
addressed with follow-up patches.
Fixes: 24333ac26d ("hwmon: (tmp401) use smb word operations instead of 2 smb byte operations")
Reported-by: David T. Wilson <david.wilson@nasa.gov>
Cc: David T. Wilson <david.wilson@nasa.gov>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fce15c45d3 ]
The detect function had a comment "Make compiler happy" when id did not
read the second configuration register. As it turns out, the code was
checking the contents of this register for manufacturer ID 0xA1 (NXP
Semiconductor/Philips), but never actually read the register. So it
wasn't surprising that the compiler complained, and it indeed had a point.
Fix the code to read the register contents for manufacturer ID 0xa1.
At the same time, the code was reading the register for manufacturer ID
0x41 (Analog Devices), but it was not using the results. In effect it was
just checking if reading the register returned an error. That doesn't
really add much if any value, so stop doing that.
Fixes: f90be42fb3 ("hwmon: (lm90) Refactor reading of config2 register")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 266423e60e ]
...and gpio-ranges
pinctrl-bcm2835 is a combined pinctrl/gpio driver. Currently the gpio
side is registered first, but this breaks gpio hogs (which are
configured during gpiochip_add_data). Part of the hog initialisation
is a call to pinctrl_gpio_request, and since the pinctrl driver hasn't
yet been registered this results in an -EPROBE_DEFER from which it can
never recover.
Change the initialisation sequence to register the pinctrl driver
first.
This also solves a similar problem with the gpio-ranges property, which
is required in order for released pins to be returned to inputs.
Fixes: 73345a18d4 ("pinctrl: bcm2835: Pass irqchip when adding gpiochip")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211206092237.4105895-2-phil@raspberrypi.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99d7fbb5ce ]
Because platform_get_irq() could fail and return error irq.
Therefore, it might be better to check it if order to avoid the use of
error irq.
Fixes: 797047f875 ("net: ks8851: Implement Parallel bus operations")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb93b3e11d ]
Because platform_get_irq() could fail and return error irq.
Therefore, it might be better to check it if order to avoid the use of
error irq.
Fixes: ae150435b5 ("smsc: Move the SMC (SMSC) drivers")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db6d6afe38 ]
I find that platform_get_irq() will not always succeed.
It will return error irq in case of the failure.
Therefore, it might be better to check it if order to avoid the use of
error irq.
Fixes: 658d439b22 ("fjes: Introduce FUJITSU Extended Socket Network Device driver")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c15b05bae ]
When 802.3ad bond mode is configured the ad_actor_system option is set to
"00:00:00:00:00:00". But when trying to set the all-zeroes MAC as actors'
system address it was failing with EINVAL.
An all-zeroes ethernet address is valid, only multicast addresses are not
valid values.
Fixes: 171a42c38c ("bonding: add netlink support for sys prio, actor sys mac, and port key")
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/20211221111345.2462-1-ffmancera@riseup.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ed1d59211 ]
virtio_net_hdr_set_proto infers skb->protocol from the virtio_net_hdr
gso_type, to avoid packets getting dropped for lack of a proto type.
Its protocol choice is a guess, especially in the case of UFO, where
the single VIRTIO_NET_HDR_GSO_UDP label covers both UFOv4 and UFOv6.
Skip this best effort if the field is already initialized. Whether
explicitly from userspace, or implicitly based on an earlier call to
dev_parse_header_protocol (which is more robust, but was introduced
after this patch).
Fixes: 9d2f67e43b ("net/packet: fix packet drop as of virtio gso")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20211220145027.2784293-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60ec7fcfe7 ]
The return value of kcalloc() needs to be checked.
To avoid dereference of null pointer in case of the failure of alloc.
Therefore, it might be better to change the return type of
qlcnic_sriov_alloc_vlans() and return -ENOMEM when alloc fails and
return 0 the others.
Also, qlcnic_sriov_set_guest_vlan_mode() and __qlcnic_pci_sriov_enable()
should deal with the return value of qlcnic_sriov_alloc_vlans().
Fixes: 154d0c810c ("qlcnic: VLAN enhancement for 84XX adapters")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39e660687a ]
Currently, the imx6q-wandboard Ethernet does not transmit any
data.
This issue has been exposed by commit f5d9aa79df ("ARM: imx6q:
remove clk-out fixup for the Atheros AR8031 and AR8035 PHYs").
Fix it by describing the qca,clk-out-frequency property as suggested
by the commit above.
Fixes: 77591e4245 ("ARM: dts: imx6qdl-wandboard: add ethernet PHY description")
Signed-off-by: Martin Haaß <vvvrrooomm@gmail.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ebb966d3bd ]
In commit 5648b5e116 ("netfilter: nfnetlink_queue: fix OOB when mac
header was cleared"), the test for non-empty MAC header introduced in
commit 2c38de4c1f ("netfilter: fix looped (broad|multi)cast's MAC
handling") has been replaced with a test for a set MAC header.
This breaks the case when the MAC header has been reset (using
skb_reset_mac_header), as is the case with looped-back multicast
packets. As a result, the packets ending up in NFQUEUE get a bogus
hwaddr interpreted from the first bytes of the IP header.
This patch adds a test for a non-empty MAC header in addition to the
test for a set MAC header. The same two tests are also implemented in
nfnetlink_log.c, where the initial code of commit 2c38de4c1f
("netfilter: fix looped (broad|multi)cast's MAC handling") has not been
touched, but where supposedly the same situation may happen.
Fixes: 5648b5e116 ("netfilter: nfnetlink_queue: fix OOB when mac header was cleared")
Signed-off-by: Ignacy Gawędzki <ignacy.gawedzki@green-communications.fr>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9c6e071913 upstream.
Now that we can check out overlapping extents in leaf block and
out-of-order index extents in index block. But the .ee_block in the
first extent of one leaf block should equal to the .ei_block in it's
parent index extent entry. This patch add a check to verify such
inconsistent between the index and leaf block.
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Link: https://lore.kernel.org/r/20210908120850.4012324-3-yi.zhang@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8dd27feced upstream.
After commit 5946d08937 ("ext4: check for overlapping extents in
ext4_valid_extent_entries()"), we can check out the overlapping extent
entry in leaf extent blocks. But the out-of-order extent entry in index
extent blocks could also trigger bad things if the filesystem is
inconsistent. So this patch add a check to figure out the out-of-order
index extents and return error.
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Theodore Ts'o <tytso@mit.edu>
Link: https://lore.kernel.org/r/20210908120850.4012324-2-yi.zhang@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f2f87d51a upstream.
In the most error path of current extents updating operations are not
roll back partial updates properly when some bad things happens(.e.g in
ext4_ext_insert_extent()). So we may get an inconsistent extents tree
if journal has been aborted due to IO error, which may probability lead
to BUGON later when we accessing these extent entries in errors=continue
mode. This patch drop extent buffer's verify flag before updatng the
contents in ext4_ext_get_access(), and reset it after updating in
__ext4_ext_dirty(). After this patch we could force to check the extent
buffer if extents tree updating was break off, make sure the extents are
consistent.
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Theodore Ts'o <tytso@mit.edu>
Link: https://lore.kernel.org/r/20210908120850.4012324-4-yi.zhang@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e6f8d1fa1 upstream.
Similar to
commit 231ad7f409 ("Makefile: infer --target from ARCH for CC=clang")
There really is no point in setting --target based on
$CROSS_COMPILE_COMPAT for clang when the integrated assembler is being
used, since
commit ef94340583 ("arm64: vdso32: drop -no-integrated-as flag").
Allows COMPAT_VDSO to be selected without setting $CROSS_COMPILE_COMPAT
when using clang and lld together.
Before:
$ ARCH=arm64 CROSS_COMPILE_COMPAT=arm-linux-gnueabi- make -j72 LLVM=1 defconfig
$ grep CONFIG_COMPAT_VDSO .config
CONFIG_COMPAT_VDSO=y
$ ARCH=arm64 make -j72 LLVM=1 defconfig
$ grep CONFIG_COMPAT_VDSO .config
$
After:
$ ARCH=arm64 CROSS_COMPILE_COMPAT=arm-linux-gnueabi- make -j72 LLVM=1 defconfig
$ grep CONFIG_COMPAT_VDSO .config
CONFIG_COMPAT_VDSO=y
$ ARCH=arm64 make -j72 LLVM=1 defconfig
$ grep CONFIG_COMPAT_VDSO .config
CONFIG_COMPAT_VDSO=y
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Suggested-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Link: https://lore.kernel.org/r/20211019223646.1146945-5-ndesaulniers@google.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a regression introduced in 131f132203
(see also https://github.com/raspberrypi/linux/issues/4791).
The tc358743 driver refused to bind to the device. The irs1125
driver is likely behaving similarly.
The new unified cam1_clk node that represents the fixed on-board
oscillator is marked as disabled by default. These overlays didn't
expect this and so the clock nodes were stuck in disabled state.
This commit just adds the required status = "okay" line. Other sensor
drivers do this too.
commit be81992f90 upstream.
In case a guest isn't consuming incoming network traffic as fast as it
is coming in, xen-netback is buffering network packages in unlimited
numbers today. This can result in host OOM situations.
Commit f48da8b14d ("xen-netback: fix unlimited guest Rx internal
queue and carrier flapping") meant to introduce a mechanism to limit
the amount of buffered data by stopping the Tx queue when reaching the
data limit, but this doesn't work for cases like UDP.
When hitting the limit don't queue further SKBs, but drop them instead.
In order to be able to tell Rx packages have been dropped increment the
rx_dropped statistics counter in this case.
It should be noted that the old solution to continue queueing SKBs had
the additional problem of an overflow of the 32-bit rx_queue_len value
would result in intermittent Tx queue enabling.
This is part of XSA-392
Fixes: f48da8b14d ("xen-netback: fix unlimited guest Rx internal queue and carrier flapping")
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6032046ec4 upstream.
Commit 1d5d485239 ("xen-netback: require fewer guest Rx slots when
not using GSO") introduced a security problem in netback, as an
interface would only be regarded to be stalled if no slot is available
in the rx queue ring page. In case the SKB at the head of the queued
requests will need more than one rx slot and only one slot is free the
stall detection logic will never trigger, as the test for that is only
looking for at least one slot to be free.
Fix that by testing for the needed number of slots instead of only one
slot being available.
In order to not have to take the rx queue lock that often, store the
number of needed slots in the queue data. As all SKB dequeue operations
happen in the rx queue kernel thread this is safe, as long as the
number of needed slots is accessed via READ/WRITE_ONCE() only and
updates are always done with the rx queue lock held.
Add a small helper for obtaining the number of free slots.
This is part of XSA-392
Fixes: 1d5d485239 ("xen-netback: require fewer guest Rx slots when not using GSO")
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe415186b4 upstream.
The Xen console driver is still vulnerable for an attack via excessive
number of events sent by the backend. Fix that by using a lateeoi event
channel.
For the normal domU initial console this requires the introduction of
bind_evtchn_to_irq_lateeoi() as there is no xenbus device available
at the time the event channel is bound to the irq.
As the decision whether an interrupt was spurious or not requires to
test for bytes having been read from the backend, move sending the
event into the if statement, as sending an event without having found
any bytes to be read is making no sense at all.
This is part of XSA-391
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b27d47950e upstream.
The Xen netfront driver is still vulnerable for an attack via excessive
number of events sent by the backend. Fix that by using lateeoi event
channels.
For being able to detect the case of no rx responses being added while
the carrier is down a new lock is needed in order to update and test
rsp_cons and the number of seen unconsumed responses atomically.
This is part of XSA-391
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0fd08a34e8 upstream.
The Xen blkfront driver is still vulnerable for an attack via excessive
number of events sent by the backend. Fix that by using lateeoi event
channels.
This is part of XSA-391
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b1da99b84 upstream.
Fix drivers/bus/ti-sysc.c:2494:13: error: variable 'error' set but not
used introduced by commit 9d88136120 ("bus: ti-sysc: Add quirk handling
for reinit on context lost").
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f5573cfe7 upstream.
Syzbot triggered the following warning in ovl_workdir_create() ->
ovl_create_real():
if (!err && WARN_ON(!newdentry->d_inode)) {
The reason is that the cgroup2 filesystem returns from mkdir without
instantiating the new dentry.
Weird filesystems such as this will be rejected by overlayfs at a later
stage during setup, but to prevent such a warning, call ovl_mkdir_real()
directly from ovl_workdir_create() and reject this case early.
Reported-and-tested-by: syzbot+75eab84fd0af9e8bf66b@syzkaller.appspotmail.com
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 44870a9e7a upstream.
Syzbot reported, that mxl111sf_ctrl_msg() uses uninitialized
mutex. The problem was in wrong mutex_init() location.
Previous mutex_init(&state->msg_lock) call was in ->init() function, but
dvb_usbv2_init() has this order of calls:
dvb_usbv2_init()
dvb_usbv2_adapter_init()
dvb_usbv2_adapter_frontend_init()
props->frontend_attach()
props->init()
Since mxl111sf_* devices call mxl111sf_ctrl_msg() in ->frontend_attach()
internally we need to initialize state->msg_lock before
frontend_attach(). To achieve it, ->probe() call added to all mxl111sf_*
devices, which will simply initiaize mutex.
Reported-and-tested-by: syzbot+5ca0bf339f13c4243001@syzkaller.appspotmail.com
Fixes: 8572211842 ("[media] mxl111sf: convert to new DVB USB")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd0687c18e upstream.
Do not sleep in poll() when the need_wakeup flag is set. When this
flag is set, the application needs to explicitly wake up the driver
with a syscall (poll, recvmsg, sendmsg, etc.) to guarantee that Rx
and/or Tx processing will be processed promptly. But the current code
in poll(), sleeps first then wakes up the driver. This means that no
driver processing will occur (baring any interrupts) until the timeout
has expired.
Fix this by checking the need_wakeup flag first and if set, wake the
driver and return to the application. Only if need_wakeup is not set
should the process sleep if there is a timeout set in the poll() call.
Fixes: 77cd0d7b3f ("xsk: add support for need_wakeup flag in AF_XDP rings")
Reported-by: Keith Wiles <keith.wiles@intel.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/bpf/20211214102607.7677-1-magnus.karlsson@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 737e65c795 upstream.
According to the i.MX6ULL Reference Manual, pad CSI_DATA07 may
have the ESAI_TX0 functionality, not ESAI_T0.
Also, NXP's i.MX Config Tools 10.0 generates dtsi with the
MX6ULL_PAD_CSI_DATA07__ESAI_TX0 naming, so fix it accordingly.
There are no devicetree users in mainline that use the old name,
so just remove the old entry.
Fixes: c201369d4a ("ARM: dts: imx6ull: add imx6ull support")
Reported-by: George Makarov <georgemakarov1@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a02dcde595 upstream.
A new warning in clang points out a few places in this driver where a
bitwise OR is being used with boolean types:
drivers/input/touchscreen.c:81:17: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
data_present = touchscreen_get_prop_u32(dev, "touchscreen-min-x",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
This use of a bitwise OR is intentional, as bitwise operations do not
short circuit, which allows all the calls to touchscreen_get_prop_u32()
to happen so that the last parameter is initialized while coalescing the
results of the calls to make a decision after they are all evaluated.
To make this clearer to the compiler, use the '|=' operator to assign
the result of each touchscreen_get_prop_u32() call to data_present,
which keeps the meaning of the code the same but makes it obvious that
every one of these calls is expected to happen.
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20211014205757.3474635-1-nathan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e8c11b6b3 upstream.
Even after commit e1d7ba8735 ("time: Always make sure wall_to_monotonic
isn't positive") it is still possible to make wall_to_monotonic positive
by running the following code:
int main(void)
{
struct timespec time;
clock_gettime(CLOCK_MONOTONIC, &time);
time.tv_nsec = 0;
clock_settime(CLOCK_REALTIME, &time);
return 0;
}
The reason is that the second parameter of timespec64_compare(), ts_delta,
may be unnormalized because the delta is calculated with an open coded
substraction which causes the comparison of tv_sec to yield the wrong
result:
wall_to_monotonic = { .tv_sec = -10, .tv_nsec = 900000000 }
ts_delta = { .tv_sec = -9, .tv_nsec = -900000000 }
That makes timespec64_compare() claim that wall_to_monotonic < ts_delta,
but actually the result should be wall_to_monotonic > ts_delta.
After normalization, the result of timespec64_compare() is correct because
the tv_sec comparison is not longer misleading:
wall_to_monotonic = { .tv_sec = -10, .tv_nsec = 900000000 }
ts_delta = { .tv_sec = -10, .tv_nsec = 100000000 }
Use timespec64_sub() to ensure that ts_delta is normalized, which fixes the
issue.
Fixes: e1d7ba8735 ("time: Always make sure wall_to_monotonic isn't positive")
Signed-off-by: Yu Liao <liaoyu15@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211213135727.1656662-1-liaoyu15@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c33ff7288 upstream.
Commit fab8a02b73 ("serial: 8250_fintek: Enable high speed mode on Fintek F81866")
introduced support to use high baudrate with Fintek SuperIO UARTs. It'll
change clocksources when the UART probed.
But when user add kernel parameter "console=ttyS0,115200 console=tty0" to make
the UART as console output, the console will output garbled text after the
following kernel message.
[ 3.681188] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
The issue is occurs in following step:
probe_setup_port() -> fintek_8250_goto_highspeed()
It change clocksource from 115200 to 921600 with wrong time, it should change
clocksource in set_termios() not in probed. The following 3 patches are
implemented change clocksource in fintek_8250_set_termios().
Commit 58178914ae ("serial: 8250_fintek: UART dynamic clocksource on Fintek F81216H")
Commit 195638b6d4 ("serial: 8250_fintek: UART dynamic clocksource on Fintek F81866")
Commit 423d9118c6 ("serial: 8250_fintek: Add F81966 Support")
Due to the high baud rate had implemented above 3 patches and the patch
Commit fab8a02b73 ("serial: 8250_fintek: Enable high speed mode on Fintek F81866")
is bugged, So this patch will remove it.
Fixes: fab8a02b73 ("serial: 8250_fintek: Enable high speed mode on Fintek F81866")
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Link: https://lore.kernel.org/r/20211215075835.2072-1-hpeter+linux_kernel@gmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit edaa26334c upstream.
The donation calculation logic assumes that the donor has non-zero
after-donation hweight, so the lowest active hweight a donating cgroup can
have is 2 so that it can donate 1 while keeping the other 1 for itself.
Earlier, we only donated from cgroups with sizable surpluses so this
condition was always true. However, with the precise donation algorithm
implemented, f1de2439ec ("blk-iocost: revamp donation amount
determination") made the donation amount calculation exact enabling even low
hweight cgroups to donate.
This means that in rare occasions, a cgroup with active hweight of 1 can
enter donation calculation triggering the following warning and then a
divide-by-zero oops.
WARNING: CPU: 4 PID: 0 at block/blk-iocost.c:1928 transfer_surpluses.cold+0x0/0x53 [884/94867]
...
RIP: 0010:transfer_surpluses.cold+0x0/0x53
Code: 92 ff 48 c7 c7 28 d1 ab b5 65 48 8b 34 25 00 ae 01 00 48 81 c6 90 06 00 00 e8 8b 3f fe ff 48 c7 c0 ea ff ff ff e9 95 ff 92 ff <0f> 0b 48 c7 c7 30 da ab b5 e8 71 3f fe ff 4c 89 e8 4d 85 ed 74 0
4
...
Call Trace:
<IRQ>
ioc_timer_fn+0x1043/0x1390
call_timer_fn+0xa1/0x2c0
__run_timers.part.0+0x1ec/0x2e0
run_timer_softirq+0x35/0x70
...
iocg: invalid donation weights in /a/b: active=1 donating=1 after=0
Fix it by excluding cgroups w/ active hweight < 2 from donating. Excluding
these extreme low hweight donations shouldn't affect work conservation in
any meaningful way.
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: f1de2439ec ("blk-iocost: revamp donation amount determination")
Cc: stable@vger.kernel.org # v5.10+
Link: https://lore.kernel.org/r/Ybfh86iSvpWKxhVM@slm.duckdns.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33fab97249 upstream.
When creating a subvolume, at create_subvol(), we allocate an anonymous
device and later call btrfs_get_new_fs_root(), which in turn just calls
btrfs_get_root_ref(). There we call btrfs_init_fs_root() which assigns
the anonymous device to the root, but if after that call there's an error,
when we jump to 'fail' label, we call btrfs_put_root(), which frees the
anonymous device and then returns an error that is propagated back to
create_subvol(). Than create_subvol() frees the anonymous device again.
When this happens, if the anonymous device was not reallocated after
the first time it was freed with btrfs_put_root(), we get a kernel
message like the following:
(...)
[13950.282466] BTRFS: error (device dm-0) in create_subvol:663: errno=-5 IO failure
[13950.283027] ida_free called for id=65 which is not allocated.
[13950.285974] BTRFS info (device dm-0): forced readonly
(...)
If the anonymous device gets reallocated by another btrfs filesystem
or any other kernel subsystem, then bad things can happen.
So fix this by setting the root's anonymous device to 0 at
btrfs_get_root_ref(), before we call btrfs_put_root(), if an error
happened.
Fixes: 2dfb1e43f5 ("btrfs: preallocate anon block device at first phase of snapshot creation")
CC: stable@vger.kernel.org # 5.10+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f35838a693 upstream.
Line 1169 (#3) allocates a memory chunk for victim_name by kmalloc(),
but when the function returns in line 1184 (#4) victim_name allocated
by line 1169 (#3) is not freed, which will lead to a memory leak.
There is a similar snippet of code in this function as allocating a memory
chunk for victim_name in line 1104 (#1) as well as releasing the memory
in line 1116 (#2).
We should kfree() victim_name when the return value of backref_in_log()
is less than zero and before the function returns in line 1184 (#4).
1057 static inline int __add_inode_ref(struct btrfs_trans_handle *trans,
1058 struct btrfs_root *root,
1059 struct btrfs_path *path,
1060 struct btrfs_root *log_root,
1061 struct btrfs_inode *dir,
1062 struct btrfs_inode *inode,
1063 u64 inode_objectid, u64 parent_objectid,
1064 u64 ref_index, char *name, int namelen,
1065 int *search_done)
1066 {
1104 victim_name = kmalloc(victim_name_len, GFP_NOFS);
// #1: kmalloc (victim_name-1)
1105 if (!victim_name)
1106 return -ENOMEM;
1112 ret = backref_in_log(log_root, &search_key,
1113 parent_objectid, victim_name,
1114 victim_name_len);
1115 if (ret < 0) {
1116 kfree(victim_name); // #2: kfree (victim_name-1)
1117 return ret;
1118 } else if (!ret) {
1169 victim_name = kmalloc(victim_name_len, GFP_NOFS);
// #3: kmalloc (victim_name-2)
1170 if (!victim_name)
1171 return -ENOMEM;
1180 ret = backref_in_log(log_root, &search_key,
1181 parent_objectid, victim_name,
1182 victim_name_len);
1183 if (ret < 0) {
1184 return ret; // #4: missing kfree (victim_name-2)
1185 } else if (!ret) {
1241 return 0;
1242 }
Fixes: d3316c8233 ("btrfs: Properly handle backref_in_log retval")
CC: stable@vger.kernel.org # 5.10+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Jianglei Nie <niejianglei2021@163.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 83b67041f3 upstream.
When generalising GPIO support and adding support for CP2102N, the GPIO
registration for some CP2105 devices accidentally broke. Specifically,
when all the pins of a port are in "modem" mode, and thus unavailable
for GPIO use, the GPIO chip would now be registered without having
initialised the number of GPIO lines. This would in turn be rejected by
gpiolib and some errors messages would be printed (but importantly probe
would still succeed).
Fix this by initialising the number of GPIO lines before registering the
GPIO chip.
Note that as for the other device types, and as when all CP2105 pins are
muxed for LED function, the GPIO chip is registered also when no pins
are available for GPIO use.
Reported-by: Maarten Brock <m.brock@vanmierlo.com>
Link: https://lore.kernel.org/r/5eb560c81d2ea1a2b4602a92d9f48a89@vanmierlo.com
Fixes: c8acfe0aad ("USB: serial: cp210x: implement GPIO support for CP2102N")
Cc: stable@vger.kernel.org # 4.19
Cc: Karoly Pados <pados@pados.hu>
Link: https://lore.kernel.org/r/20211126094348.31698-1-johan@kernel.org
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Maarten Brock <m.brock@vanmierlo.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 83dbf898a2 upstream.
Masking all unused MSI-X entries is done to ensure that a crash kernel
starts from a clean slate, which correponds to the reset state of the
device as defined in the PCI-E specificion 3.0 and later:
Vector Control for MSI-X Table Entries
--------------------------------------
"00: Mask bit: When this bit is set, the function is prohibited from
sending a message using this MSI-X Table entry.
...
This bit’s state after reset is 1 (entry is masked)."
A Marvell NVME device fails to deliver MSI interrupts after trying to
enable MSI-X interrupts due to that masking. It seems to take the MSI-X
mask bits into account even when MSI-X is disabled.
While not specification compliant, this can be cured by moving the masking
into the success path, so that the MSI-X table entries stay in device reset
state when the MSI-X setup fails.
[ tglx: Move it into the success path, add comment and amend changelog ]
Fixes: aa8092c1d1 ("PCI/MSI: Mask all unused MSI-X entries")
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-pci@vger.kernel.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211210161025.3287927-1-sr@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fac6bf87c5 upstream.
When activate_stm_id_vb_detection is enabled, ID and Vbus detection relies
on sensing comparators. This detection needs time to stabilize.
A delay was already applied in dwc2_resume() when reactivating the
detection, but it wasn't done in dwc2_probe().
This patch adds delay after enabling STM ID/VBUS detection. Then, ID state
is good when initializing gadget and host, and avoid to get a wrong
Connector ID Status Change interrupt.
Fixes: a415083a11 ("usb: dwc2: add support for STM32MP15 SoCs USB OTG HS and FS")
Cc: stable <stable@vger.kernel.org>
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211207124510.268841-1-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1aa2abb33a ]
The ability to write to MSR_IA32_PERF_CAPABILITIES from the host should
not depend on guest visible CPUID entries, even if just to allow
creating/restoring guest MSRs and CPUIDs in any sequence.
Fixes: 27461da310 ("KVM: x86/pmu: Support full width counting")
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20211216165213.338923-3-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f08adf5add ]
Szymon rightly pointed out that the previous check for the endpoint
direction in bRequestType was not looking at only the bit involved, but
rather the whole value. Normally this is ok, but for some request
types, bits other than bit 8 could be set and the check for the endpoint
length could not stall correctly.
Fix that up by only checking the single bit.
Fixes: 153a2d7e33 ("USB: gadget: detect too-big endpoint 0 requests")
Cc: Felipe Balbi <balbi@kernel.org>
Reported-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Link: https://lore.kernel.org/r/20211214184621.385828-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2fcbf81c3 ]
The libbpf CI reported occasional failure in btf_skc_cls_ingress:
test_syncookie:FAIL:Unexpected syncookie states gen_cookie:80326634 recv_cookie:0
bpf prog error at line 97
"error at line 97" means the bpf prog cannot find the listening socket
when the final ack is received. It then skipped processing
the syncookie in the final ack which then led to "recv_cookie:0".
The problem is the userspace program did not do accept() and went
ahead to close(listen_fd) before the kernel (and the bpf prog) had
a chance to process the final ack.
The fix is to add accept() call so that the userspace will wait for
the kernel to finish processing the final ack first before close()-ing
everything.
Fixes: 9a856cae22 ("bpf: selftest: Add test_btf_skc_cls_ingress")
Reported-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20211216191630.466151-1-kafai@fb.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b8e6e7824 ]
The descriptor list is a shared resource across all of the transmit queues, and
the locking mechanism used today only protects concurrency across a given
transmit queue between the transmit and reclaiming. This creates an opportunity
for the SYSTEMPORT hardware to work on corrupted descriptors if we have
multiple producers at once which is the case when using multiple transmit
queues.
This was particularly noticeable when using multiple flows/transmit queues and
it showed up in interesting ways in that UDP packets would get a correct UDP
header checksum being calculated over an incorrect packet length. Similarly TCP
packets would get an equally correct checksum computed by the hardware over an
incorrect packet length.
The SYSTEMPORT hardware maintains an internal descriptor list that it re-arranges
when the driver produces a new descriptor anytime it writes to the
WRITE_PORT_{HI,LO} registers, there is however some delay in the hardware to
re-organize its descriptors and it is possible that concurrent TX queues
eventually break this internal allocation scheme to the point where the
length/status part of the descriptor gets used for an incorrect data buffer.
The fix is to impose a global serialization for all TX queues in the short
section where we are writing to the WRITE_PORT_{HI,LO} registers which solves
the corruption even with multiple concurrent TX queues being used.
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211215202450.4086240-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c15b3123f ]
In nginx/wrk benchmark, there's a hung problem with high probability
on case likes that: (client will last several minutes to exit)
server: smc_run nginx
client: smc_run wrk -c 10000 -t 1 http://server
Client hangs with the following backtrace:
0 [ffffa7ce8Of3bbf8] __schedule at ffffffff9f9eOd5f
1 [ffffa7ce8Of3bc88] schedule at ffffffff9f9eløe6
2 [ffffa7ce8Of3bcaO] schedule_timeout at ffffffff9f9e3f3c
3 [ffffa7ce8Of3bd2O] wait_for_common at ffffffff9f9el9de
4 [ffffa7ce8Of3bd8O] __flush_work at ffffffff9fOfeOl3
5 [ffffa7ce8øf3bdfO] smc_release at ffffffffcO697d24 [smc]
6 [ffffa7ce8Of3be2O] __sock_release at ffffffff9f8O2e2d
7 [ffffa7ce8Of3be4ø] sock_close at ffffffff9f8ø2ebl
8 [ffffa7ce8øf3be48] __fput at ffffffff9f334f93
9 [ffffa7ce8Of3be78] task_work_run at ffffffff9flOlff5
10 [ffffa7ce8Of3beaO] do_exit at ffffffff9fOe5Ol2
11 [ffffa7ce8Of3bflO] do_group_exit at ffffffff9fOe592a
12 [ffffa7ce8Of3bf38] __x64_sys_exit_group at ffffffff9fOe5994
13 [ffffa7ce8Of3bf4O] do_syscall_64 at ffffffff9f9d4373
14 [ffffa7ce8Of3bfsO] entry_SYSCALL_64_after_hwframe at ffffffff9fa0007c
This issue dues to flush_work(), which is used to wait for
smc_connect_work() to finish in smc_release(). Once lots of
smc_connect_work() was pending or all executing work dangling,
smc_release() has to block until one worker comes to free, which
is equivalent to wait another smc_connnect_work() to finish.
In order to fix this, There are two changes:
1. For those idle smc_connect_work(), cancel it from the workqueue; for
executing smc_connect_work(), waiting for it to finish. For that
purpose, replace flush_work() with cancel_work_sync().
2. Since smc_connect() hold a reference for passive closing, if
smc_connect_work() has been cancelled, release the reference.
Fixes: 24ac3a08e6 ("net/smc: rebuild nonblocking connect")
Reported-by: Tony Lu <tonylu@linux.alibaba.com>
Tested-by: Dust Li <dust.li@linux.alibaba.com>
Reviewed-by: Dust Li <dust.li@linux.alibaba.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Link: https://lore.kernel.org/r/1639571361-101128-1-git-send-email-alibuda@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a03ef676a ]
When printing netdev features %pNF already takes care of the 0x prefix,
remove the explicit one.
Fixes: 6413139dfc ("skbuff: increase verbosity when dumping skb data")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 407ecd1bd7 ]
The return value of kmalloc() needs to be checked.
To avoid use in efx_nic_update_stats() in case of the failure of alloc.
Fixes: b593b6f1b4 ("sfc_ef100: statistics gathering")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 481221775d ]
Zero-initialize memory for new map's value in function nsim_bpf_map_alloc
since it may cause a potential kernel information leak issue, as follows:
1. nsim_bpf_map_alloc calls nsim_map_alloc_elem to allocate elements for
a new map.
2. nsim_map_alloc_elem uses kmalloc to allocate map's value, but doesn't
zero it.
3. A user application can use IOCTL BPF_MAP_LOOKUP_ELEM to get specific
element's information in the map.
4. The kernel function map_lookup_elem will call bpf_map_copy_value to get
the information allocated at step-2, then use copy_to_user to copy to the
user buffer.
This can only leak information for an array map.
Fixes: 395cacb5f1 ("netdevsim: bpf: support fake map offload")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Haimin Zhang <tcs.kernel@gmail.com>
Link: https://lore.kernel.org/r/20211215111530.72103-1-tcs.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf0a375055 ]
The MDIO bus speed must be initialized before talking to the PHY the first
time in order to avoid talking to it using a speed that the PHY doesn't
support.
This fixes HW initialization error -17 (IXGBE_ERR_PHY_ADDR_INVALID) on
Denverton CPUs (a.k.a. the Atom C3000 family) on ports with a 10Gb network
plugged in. On those devices, HLREG0[MDCSPD] resets to 1, which combined
with the 10Gb network results in a 24MHz MDIO speed, which is apparently
too fast for the connected PHY. PHY register reads over MDIO bus return
garbage, leading to initialization failure.
Reproduced with Linux kernel 4.19 and 5.15-rc7. Can be reproduced using
the following setup:
* Use an Atom C3000 family system with at least one X552 LAN on the SoC
* Disable PXE or other BIOS network initialization if possible
(the interface must not be initialized before Linux boots)
* Connect a live 10Gb Ethernet cable to an X550 port
* Power cycle (not reset, doesn't always work) the system and boot Linux
* Observe: ixgbe interfaces w/ 10GbE cables plugged in fail with error -17
Fixes: e84db72727 ("ixgbe: Introduce function to control MDIO speed")
Signed-off-by: Cyril Novikov <cnovikov@lynx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 271225fd57 ]
Commit a296d665ea ("ixgbe: Add ethtool support to enable 2.5 and 5.0
Gbps support") introduced suppression of the advertisement of NBASE-T
speeds by default, according to Todd Fujinaka to accommodate customers
with network switches which could not cope with advertised NBASE-T
speeds, as posted in the E1000-devel mailing list:
https://sourceforge.net/p/e1000/mailman/message/37106269/
However, the suppression was not documented at all, nor was how to
enable NBASE-T support.
Properly document the NBASE-T suppression and how to enable NBASE-T
support.
Fixes: a296d665ea ("ixgbe: Add ethtool support to enable 2.5 and 5.0 Gbps support")
Reported-by: Robert Schlabbach <robert_s@gmx.net>
Signed-off-by: Robert Schlabbach <robert_s@gmx.net>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0182d1f3fa ]
The LTR maximum value was incorrectly written using the scale from
the LTR minimum value. This would cause incorrect values to be sent,
in cases where the initial calculation lead to different min/max scales.
Fixes: 707abf0695 ("igc: Add initial LTR support")
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6d335a60d ]
In `igbvf_probe`, if register_netdev() fails, the program will go to
label err_hw_init, and then to label err_ioremap. In free_netdev() which
is just below label err_ioremap, there is `list_for_each_entry_safe` and
`netif_napi_del` which aims to delete all entries in `dev->napi_list`.
The program has added an entry `adapter->rx_ring->napi` which is added by
`netif_napi_add` in igbvf_alloc_queues(). However, adapter->rx_ring has
been freed below label err_hw_init. So this a UAF.
In terms of how to patch the problem, we can refer to igbvf_remove() and
delete the entry before `adapter->rx_ring`.
The KASAN logs are as follows:
[ 35.126075] BUG: KASAN: use-after-free in free_netdev+0x1fd/0x450
[ 35.127170] Read of size 8 at addr ffff88810126d990 by task modprobe/366
[ 35.128360]
[ 35.128643] CPU: 1 PID: 366 Comm: modprobe Not tainted 5.15.0-rc2+ #14
[ 35.129789] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014
[ 35.131749] Call Trace:
[ 35.132199] dump_stack_lvl+0x59/0x7b
[ 35.132865] print_address_description+0x7c/0x3b0
[ 35.133707] ? free_netdev+0x1fd/0x450
[ 35.134378] __kasan_report+0x160/0x1c0
[ 35.135063] ? free_netdev+0x1fd/0x450
[ 35.135738] kasan_report+0x4b/0x70
[ 35.136367] free_netdev+0x1fd/0x450
[ 35.137006] igbvf_probe+0x121d/0x1a10 [igbvf]
[ 35.137808] ? igbvf_vlan_rx_add_vid+0x100/0x100 [igbvf]
[ 35.138751] local_pci_probe+0x13c/0x1f0
[ 35.139461] pci_device_probe+0x37e/0x6c0
[ 35.165526]
[ 35.165806] Allocated by task 366:
[ 35.166414] ____kasan_kmalloc+0xc4/0xf0
[ 35.167117] foo_kmem_cache_alloc_trace+0x3c/0x50 [igbvf]
[ 35.168078] igbvf_probe+0x9c5/0x1a10 [igbvf]
[ 35.168866] local_pci_probe+0x13c/0x1f0
[ 35.169565] pci_device_probe+0x37e/0x6c0
[ 35.179713]
[ 35.179993] Freed by task 366:
[ 35.180539] kasan_set_track+0x4c/0x80
[ 35.181211] kasan_set_free_info+0x1f/0x40
[ 35.181942] ____kasan_slab_free+0x103/0x140
[ 35.182703] kfree+0xe3/0x250
[ 35.183239] igbvf_probe+0x1173/0x1a10 [igbvf]
[ 35.184040] local_pci_probe+0x13c/0x1f0
Fixes: d4e0fe01a3 (igbvf: add new driver to support 82576 virtual functions)
Reported-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Letu Ren <fantasquex@gmail.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 584af82154 ]
Move checking condition of VF MAC filter before clearing
or adding MAC filter to VF to prevent potential blackout caused
by removal of necessary and working VF's MAC filter.
Fixes: 1b8b062a99 ("igb: add VF trust infrastructure")
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a708376361 ]
A new warning in clang points out two instances where boolean
expressions are being used with a bitwise OR instead of logical OR:
drivers/soc/tegra/fuse/speedo-tegra20.c:72:9: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
reg = tegra_fuse_read_spare(i) |
^~~~~~~~~~~~~~~~~~~~~~~~~~
||
drivers/soc/tegra/fuse/speedo-tegra20.c:72:9: note: cast one or both operands to int to silence this warning
drivers/soc/tegra/fuse/speedo-tegra20.c:87:9: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
reg = tegra_fuse_read_spare(i) |
^~~~~~~~~~~~~~~~~~~~~~~~~~
||
drivers/soc/tegra/fuse/speedo-tegra20.c:87:9: note: cast one or both operands to int to silence this warning
2 warnings generated.
The motivation for the warning is that logical operations short circuit
while bitwise operations do not.
In this instance, tegra_fuse_read_spare() is not semantically returning
a boolean, it is returning a bit value. Use u32 for its return type so
that it can be used with either bitwise or boolean operators without any
warnings.
Fixes: 25cd5a3914 ("ARM: tegra: Add speedo-based process identification")
Link: https://github.com/ClangBuiltLinux/linux/issues/1488
Suggested-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6692b3b97 ]
The mptcp ULP extension relies on sk->sk_sock_kern being set correctly:
It prevents setsockopt(fd, IPPROTO_TCP, TCP_ULP, "mptcp", 6); from
working for plain tcp sockets (any userspace-exposed socket).
But in case of fallback, accept() can return a plain tcp sk.
In such case, sk is still tagged as 'kernel' and setsockopt will work.
This will crash the kernel, The subflow extension has a NULL ctx->conn
mptcp socket:
BUG: KASAN: null-ptr-deref in subflow_data_ready+0x181/0x2b0
Call Trace:
tcp_data_ready+0xf8/0x370
[..]
Fixes: cf7da0d66c ("mptcp: Create SUBFLOW socket for incoming connections")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa464957f7 ]
Memory is allocated for gpu_metrics_table in renoir_init_smc_tables(),
but not freed in int smu_v12_0_fini_smc_tables(). Free it!
Fixes: 95868b8576 ("drm/amd/powerplay: add Renoir support for gpu metrics export")
Signed-off-by: Lang Yu <lang.yu@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 166b6a46b7 ]
We need to return EOPNOTSUPP for the unsupported mpls action type when
setup the flow action.
In the original implement, we will return 0 for the unsupported mpls
action type, actually we do not setup it and the following actions
to the flow action entry.
Fixes: 9838b20a7f ("net: sched: take rtnl lock in tc_setup_flow_action()")
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71da1aec21 ]
The recent GRE selftests defined NUM_NETIFS=10. If the users copy
forwarding.config.sample to forwarding.config directly, they will get
error "Command line is not complete" when run the GRE tests, because
create_netif_veth() failed with no interface name defined.
Fix it by extending the NETIFS with p9 and p10.
Fixes: 2800f24854 ("selftests: forwarding: Test multipath hashing on inner IP pkts for GRE tunnel")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28a2686c18 ]
IPv6 allows binding a socket to a device then binding to an address
not on the device (__inet6_bind -> ipv6_chk_addr with strict flag
not set). Update the bind tests to reflect legacy behavior.
Fixes: 34d0302ab8 ("selftests: Add ipv6 address bind tests to fcnal-test")
Reported-by: Li Zhijian <lizhijian@fujitsu.com>
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f108ae445 ]
Commit referenced below added negative socket bind tests for VRF. The
socket binds should fail since the address to bind to is in a VRF yet
the socket is not bound to the VRF or a device within it. Update the
expected return code to check for 1 (bind failure) so the test passes
when the bind fails as expected. Add a 'show_hint' comment to explain
why the bind is expected to fail.
Fixes: 75b2b2b3db ("selftests: Add ipv4 address bind tests to fcnal-test")
Reported-by: Li Zhijian <lizhijian@fujitsu.com>
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e0147592b ]
Commit referenced below added configuration in the default VRF that
duplicates a VRF to check MD5 passwords are properly used and fail
when expected. That config should not be added all the time as it
can cause tests to pass that should not (by matching on default VRF
setup when it should not). Move the duplicate setup to a function
that is only called for the MD5 tests and add a cleanup function
to remove it after the MD5 tests.
Fixes: 5cad8bce26 ("fcnal-test: Add TCP MD5 tests for VRF")
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27cbf64a76 ]
Currently, the hns3_remove function firstly uninstall client instance,
and then uninstall acceletion engine device. The netdevice is freed in
client instance uninstall process, but acceletion engine device uninstall
process still use it to trace runtime information. This causes a use after
free problem.
So fixes it by check the instance register state to avoid use after free.
Fixes: d8355240cf ("net: hns3: add trace event support for PF/VF mailbox")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41967a37b8 ]
arch_kexec_apply_relocations_add currently ignores all errors returned
by arch_kexec_do_relocs. This means that every unknown relocation is
silently skipped causing unpredictable behavior while the relocated code
runs. Fix this by checking for errors and fail kexec_file_load if an
unknown relocation type is encountered.
The problem was found after gcc changed its behavior and used
R_390_PLT32DBL relocations for brasl instruction and relied on ld to
resolve the relocations in the final link in case direct calls are
possible. As the purgatory code is only linked partially (option -r)
ld didn't resolve the relocations leaving them for arch_kexec_do_relocs.
But arch_kexec_do_relocs doesn't know how to handle R_390_PLT32DBL
relocations so they were silently skipped. This ultimately caused an
endless loop in the purgatory as the brasl instructions kept branching
to itself.
Fixes: 71406883fd ("s390/kexec_file: Add kexec_file_load system call")
Reported-by: Tao Liu <ltao@redhat.com>
Signed-off-by: Philipp Rudo <prudo@redhat.com>
Link: https://lore.kernel.org/r/20211208130741.5821-3-prudo@redhat.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1db8f5fc2e ]
The VMADDR_CID_ANY flag used by a socket means that the socket isn't bound
to any specific CID. For example, a host vsock server may want to be bound
with VMADDR_CID_ANY, so that a guest vsock client can connect to the host
server with CID=VMADDR_CID_HOST (i.e. 2), and meanwhile, a host vsock
client can connect to the same local server with CID=VMADDR_CID_LOCAL
(i.e. 1).
The current implementation sets the destination socket's svm_cid to a
fixed CID value after the first client's connection, which isn't an
expected operation. For example, if the guest client first connects to the
host server, the server's svm_cid gets set to VMADDR_CID_HOST, then other
host clients won't be able to connect to the server anymore.
Reproduce steps:
1. Run the host server:
socat VSOCK-LISTEN:1234,fork -
2. Run a guest client to connect to the host server:
socat - VSOCK-CONNECT:2:1234
3. Run a host client to connect to the host server:
socat - VSOCK-CONNECT:1:1234
Without this patch, step 3. above fails to connect, and socat complains
"socat[1720] E connect(5, AF=40 cid:1 port:1234, 16): Connection
reset by peer".
With this patch, the above works well.
Fixes: c0cfa2d8a7 ("vsock: add multi-transports support")
Signed-off-by: Wei Wang <wei.w.wang@intel.com>
Link: https://lore.kernel.org/r/20211126011823.1760-1-wei.w.wang@intel.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ebd29f916 ]
At the moment, using the ARM32 multi_v7_defconfig always results in two
SoCs being exposed in sysfs. This is wrong, as far as I'm aware the
Qualcomm DragonBoard 410c does not actually make use of a i.MX SoC. :)
qcom-db410c:/sys/devices/soc0$ grep . *
family:Freescale i.MX
machine:Qualcomm Technologies, Inc. APQ 8016 SBC
revision:0.0
serial_number:0000000000000000
soc_id:Unknown
qcom-db410c:/sys/devices/soc1$ grep . *
family:Snapdragon
machine:APQ8016
...
This happens because imx_soc_device_init() registers the soc device
unconditionally, even when running on devices that do not make use of i.MX.
Arnd already reported this more than a year ago and even suggested a fix
similar to this commit, but for some reason it was never submitted.
Fix it by checking if the "__mxc_cpu_type" variable was actually
initialized by earlier platform code. On devices without i.MX it will
simply stay 0.
Cc: Peng Fan <peng.fan@nxp.com>
Fixes: d2199b3487 ("ARM: imx: use device_initcall for imx_soc_device_init")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/CAK8P3a0hxO1TmK6oOMQ70AHSWJnP_CAq57YMOutrxkSYNjFeuw@mail.gmail.com/
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54baf56eaa ]
Before commit fc0c209c14 ("clk: Allow parents to be specified without
string names") child clks couldn't find their parent until the parent
clk was added to a list in __clk_core_init(). After that commit, child
clks can reference their parent clks directly via a clk_hw pointer, or
they can lookup that clk_hw pointer via DT if the parent clk is
registered with an OF clk provider.
The common clk framework treats hw->core being non-NULL as "the clk is
registered" per the logic within clk_core_fill_parent_index():
parent = entry->hw->core;
/*
* We have a direct reference but it isn't registered yet?
* Orphan it and let clk_reparent() update the orphan status
* when the parent is registered.
*/
if (!parent)
Therefore we need to be extra careful to not set hw->core until the clk
is fully registered with the clk framework. Otherwise we can get into a
situation where a child finds a parent clk and we move the child clk off
the orphan list when the parent isn't actually registered, wrecking our
enable accounting and breaking critical clks.
Consider the following scenario:
CPU0 CPU1
---- ----
struct clk_hw clkBad;
struct clk_hw clkA;
clkA.init.parent_hws = { &clkBad };
clk_hw_register(&clkA) clk_hw_register(&clkBad)
... __clk_register()
hw->core = core
...
__clk_register()
__clk_core_init()
clk_prepare_lock()
__clk_init_parent()
clk_core_get_parent_by_index()
clk_core_fill_parent_index()
if (entry->hw) {
parent = entry->hw->core;
At this point, 'parent' points to clkBad even though clkBad hasn't been
fully registered yet. Ouch! A similar problem can happen if a clk
controller registers orphan clks that are referenced in the DT node of
another clk controller.
Let's fix all this by only setting the hw->core pointer underneath the
clk prepare lock in __clk_core_init(). This way we know that
clk_core_fill_parent_index() can't see hw->core be non-NULL until the
clk is fully registered.
Fixes: fc0c209c14 ("clk: Allow parents to be specified without string names")
Signed-off-by: Mike Tipton <quic_mdtipton@quicinc.com>
Link: https://lore.kernel.org/r/20211109043438.4639-1-quic_mdtipton@quicinc.com
[sboyd@kernel.org: Reword commit text, update comment]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee2a095d3b ]
The smatch static checker warned about an uninitialized symbol usage in
this function, in the case where ceph_mdsc_build_path returns an error.
It turns out that that case is harmless, but it just looks sketchy.
Initialize the variable at declaration time, and remove the unneeded
setting of it later.
Fixes: a33f6432b3 ("ceph: encode inodes' parent/d_name in cap reconnect message")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 973e524563 ]
opened_inodes is incremented twice when the same inode is opened twice
with O_RDONLY and O_WRONLY respectively.
To reproduce, run this python script, then check the metrics:
import os
for _ in range(10000):
fd_r = os.open('a', os.O_RDONLY)
fd_w = os.open('a', os.O_WRONLY)
os.close(fd_r)
os.close(fd_w)
Fixes: 1dd8d47081 ("ceph: metrics for opened files, pinned caps and opened inodes")
Signed-off-by: Hu Weiwen <sehuww@mail.scut.edu.cn>
Reviewed-by: Xiubo Li <xiubli@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f4b3ee3c85 upstream.
If the audit daemon were ever to get stuck in a stopped state the
kernel's kauditd_thread() could get blocked attempting to send audit
records to the userspace audit daemon. With the kernel thread
blocked it is possible that the audit queue could grow unbounded as
certain audit record generating events must be exempt from the queue
limits else the system enter a deadlock state.
This patch resolves this problem by lowering the kernel thread's
socket sending timeout from MAX_SCHEDULE_TIMEOUT to HZ/10 and tweaks
the kauditd_send_queue() function to better manage the various audit
queues when connection problems occur between the kernel and the
audit daemon. With this patch, the backlog may temporarily grow
beyond the defined limits when the audit daemon is stopped and the
system is under heavy audit pressure, but kauditd_thread() will
continue to make progress and drain the queues as it would for other
connection problems. For example, with the audit daemon put into a
stopped state and the system configured to audit every syscall it
was still possible to shutdown the system without a kernel panic,
deadlock, etc.; granted, the system was slow to shutdown but that is
to be expected given the extreme pressure of recording every syscall.
The timeout value of HZ/10 was chosen primarily through
experimentation and this developer's "gut feeling". There is likely
no one perfect value, but as this scenario is limited in scope (root
privileges would be needed to send SIGSTOP to the audit daemon), it
is likely not worth exposing this as a tunable at present. This can
always be done at a later date if it proves necessary.
Cc: stable@vger.kernel.org
Fixes: 5b52330bbf ("audit: fix auditd/kernel connection state tracking")
Reported-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Tested-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Reviewed-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 817fc978b5 upstream.
virtio_max_dma_size() returns the maximum DMA mapping size of the virtio
device by querying dma_max_mapping_size() for the device when the DMA
API is in use for the vring. Unfortunately, the device passed is
initialised by register_virtio_device() and does not inherit the DMA
configuration from its parent, resulting in SWIOTLB errors when bouncing
is enabled and the default 256K mapping limit (IO_TLB_SEGSIZE) is not
respected:
| virtio-pci 0000:00:01.0: swiotlb buffer is full (sz: 294912 bytes), total 1024 (slots), used 725 (slots)
Follow the pattern used elsewhere in the virtio_ring code when calling
into the DMA layer and pass the parent device to dma_max_mapping_size()
instead.
Cc: Marc Zyngier <maz@kernel.org>
Cc: Quentin Perret <qperret@google.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Signed-off-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20211201112018.25276-1-will@kernel.org
Acked-by: Jason Wang <jasowang@redhat.com>
Tested-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Fixes: e6d6dd6c87 ("virtio: Introduce virtio_max_dma_size()")
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e572ff80f0 upstream.
Make the bounds propagation in __reg_assign_32_into_64() slightly more
robust and readable by aligning it similarly as we did back in the
__reg_combine_64_into_32() counterpart. Meaning, only propagate or
pessimize them as a smin/smax pair.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3cf2b61eb0 upstream.
For the case where both s32_{min,max}_value bounds are positive, the
__reg_assign_32_into_64() directly propagates them to their 64 bit
counterparts, otherwise it pessimises them into [0,u32_max] universe and
tries to refine them later on by learning through the tnum as per comment
in mentioned function. However, that does not always happen, for example,
in mov32 operation we call zext_32_to_64(dst_reg) which invokes the
__reg_assign_32_into_64() as is without subsequent bounds update as
elsewhere thus no refinement based on tnum takes place.
Thus, not calling into the __update_reg_bounds() / __reg_deduce_bounds() /
__reg_bound_offset() triplet as we do, for example, in case of ALU ops via
adjust_scalar_min_max_vals(), will lead to more pessimistic bounds when
dumping the full register state:
Before fix:
0: (b4) w0 = -1
1: R0_w=invP4294967295
(id=0,imm=ffffffff,
smin_value=4294967295,smax_value=4294967295,
umin_value=4294967295,umax_value=4294967295,
var_off=(0xffffffff; 0x0),
s32_min_value=-1,s32_max_value=-1,
u32_min_value=-1,u32_max_value=-1)
1: (bc) w0 = w0
2: R0_w=invP4294967295
(id=0,imm=ffffffff,
smin_value=0,smax_value=4294967295,
umin_value=4294967295,umax_value=4294967295,
var_off=(0xffffffff; 0x0),
s32_min_value=-1,s32_max_value=-1,
u32_min_value=-1,u32_max_value=-1)
Technically, the smin_value=0 and smax_value=4294967295 bounds are not
incorrect, but given the register is still a constant, they break assumptions
about const scalars that smin_value == smax_value and umin_value == umax_value.
After fix:
0: (b4) w0 = -1
1: R0_w=invP4294967295
(id=0,imm=ffffffff,
smin_value=4294967295,smax_value=4294967295,
umin_value=4294967295,umax_value=4294967295,
var_off=(0xffffffff; 0x0),
s32_min_value=-1,s32_max_value=-1,
u32_min_value=-1,u32_max_value=-1)
1: (bc) w0 = w0
2: R0_w=invP4294967295
(id=0,imm=ffffffff,
smin_value=4294967295,smax_value=4294967295,
umin_value=4294967295,umax_value=4294967295,
var_off=(0xffffffff; 0x0),
s32_min_value=-1,s32_max_value=-1,
u32_min_value=-1,u32_max_value=-1)
Without the smin_value == smax_value and umin_value == umax_value invariant
being intact for const scalars, it is possible to leak out kernel pointers
from unprivileged user space if the latter is enabled. For example, when such
registers are involved in pointer arithmtics, then adjust_ptr_min_max_vals()
will taint the destination register into an unknown scalar, and the latter
can be exported and stored e.g. into a BPF map value.
Fixes: 3f50f132d8 ("bpf: Verifier, do explicit ALU32 bounds tracking")
Reported-by: Kuee K1r0a <liulin063@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1fe98f5690 upstream.
Sending them out on a different queue can cause a race condition where a
number of packets in the queue may be discarded by the receiver, because
the ADDBA request is sent too early.
This affects any driver with software A-MPDU setup which does not allocate
packet seqno in hardware on tx, regardless of whether iTXQ is used or not.
The only driver I've seen that explicitly deals with this issue internally
is mwl8k.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20211202124533.80388-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5f25e71e31 ]
This is not an unrecoverable situation. Users of kvm_read_guest_offset_cached
and kvm_write_guest_offset_cached must expect the read/write to fail, and
therefore it is possible to just return early with an error value.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 908fa88e42 ]
With the elevated 'KVM_CAP_MAX_VCPUS' value kvm_create_max_vcpus test
may hit RLIMIT_NOFILE limits:
# ./kvm_create_max_vcpus
KVM_CAP_MAX_VCPU_ID: 4096
KVM_CAP_MAX_VCPUS: 1024
Testing creating 1024 vCPUs, with IDs 0...1023.
/dev/kvm not available (errno: 24), skipping test
Adjust RLIMIT_NOFILE limits to make sure KVM_CAP_MAX_VCPUS fds can be
opened. Note, raising hard limit ('rlim_max') requires CAP_SYS_RESOURCE
capability which is generally not needed to run kvm selftests (but without
raising the limit the test is doomed to fail anyway).
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20211123135953.667434-1-vkuznets@redhat.com>
[Skip the test if the hard limit can be raised. - Paolo]
Reviewed-by: Sean Christopherson <seanjc@google.com>
Tested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 311a839a1a upstream.
Add documentation for the V4L2_CID_NOTIFY_GAINS control.
This control is required by sensors that need to know what colour
gains will be applied to pixels by downstream processing (such as by
an ISP), though the sensor does not apply these gains itself.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit a9c80593ff upstream.
We add a new control V4L2_CID_NOTIFY_GAINS which allows the sensor to
be notified what gains will be applied to the different colour
channels by subsequent processing (such as by an ISP), even though the
sensor will not apply any of these gains itself.
For Bayer sensors this will be an array control taking 4 values which
are the 4 gains arranged in the fixed order B, Gb, Gr and R,
irrespective of the exact Bayer order of the sensor itself. The use of
an array makes it straightforward to extend this control to non-Bayer
sensors (for example, sensors with an RGBW pattern) in future.
The units are in all cases linear with the default value indicating a
gain of exactly 1.0. For example, if the default value were reported as
128 then the value 192 would represent a gain of exactly 1.5.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This path actually occurs when audio is started during a hdmi mode set.
As the data will be written by vc4_hdmi_set_infoframes when packet RAM
is enabled again, don't treat as an error
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
In addition to the RGB444 output, the BCM2711 HDMI controller supports
the YUV444 and YUV422 output formats.
Let's add support for them in the driver, but still use RGB as the
preferred format.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Currently we take the max_bpc property as the bpc value and do not try
anything else.
However, what the other drivers seem to be doing is that they would try
with the highest bpc allowed by the max_bpc property and the hardware
capabilities, test if it results in an acceptable configuration, and if
not decrease the bpc and try again.
Let's use the same logic.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The current code only base its decision for whether the scrambler must be
enabled or not on the pixel clock of the mode, but doesn't take the bits
per color into account.
Let's leverage the new function to compute the clock rate in the
scrambler setup code.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
In the function that validates that the clock isn't too high, we've only
taken our controller limitations into account so far.
However, the sink can have a limit on the maximum TMDS clock it can deal
with too which is exposed through the EDID and the drm_display_info.
Make sure we check it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The code to compute our clock rate for a given setup will be called in
multiple places in the next patches, so let's create a separate function
for it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Our code is doing the same clock rate validation in multiple instances.
Let's create a helper to share the rate validation.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
In order to support the YUV output, we'll need the atomic state to know
what is the state of the associated property in the CSC setup callback.
Let's change the prototype of that callback to allow us to access it.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The current CSC setup code for the BCM2711 uses a sequence of register
writes to configure the CSC depending on whether we output using a full
or limited range.
However, with the upcoming introduction of the YUV output, we're going
to add new matrices to perform the conversions, so we should switch to
something a bit more flexible that takes the matrix as an argument and
programs the CSC accordingly.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
On BCM2711, the HDMI_CSC_CTL register value has been hardcoded to an
opaque value. Let's replace it with properly defined values.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
On the BCM2711, the HDMI_VEC_INTERFACE_XBAR register configuration
depends on whether we're using an RGB or YUV output. Let's move that
configuration to the CSC setup.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The CSC callbacks takes a boolean as an argument to tell whether we're
using the full range or limited range RGB.
However, with the upcoming YUV support, the logic will be a bit more
complex. In order to address this, let's make the callbacks take the
entire mode, and call our new helper to tell whether the full or limited
range RGB should be used.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
We're going to need to tell whether we want to run with a full or
limited range RGB output in multiple places in the code, so let's create
a helper that will return whether we need with full range or not.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The drm_hdmi_avi_infoframe_colorspace() function actually sets the
colorimetry and extended_colorimetry fields in the hdmi_avi_infoframe
structure with DRM_MODE_COLORIMETRY_* values.
To make things worse, the hdmi_avi_infoframe structure also has a
colorspace field used to signal whether an RGB or YUV output is being
used.
Let's remove the inconsistency and allow for the colorspace usage by
renaming the function.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The current code, when parsing the EDID Deep Color depths, that the
YUV422 cannot be used, referring to the HDMI 1.3 Specification.
This specification, in its section 6.2.4, indeed states:
For each supported Deep Color mode, RGB 4:4:4 shall be supported and
optionally YCBCR 4:4:4 may be supported.
YCBCR 4:2:2 is not permitted for any Deep Color mode.
This indeed can be interpreted like the code does, but the HDMI 1.4
specification further clarifies that statement in its section 6.2.4:
For each supported Deep Color mode, RGB 4:4:4 shall be supported and
optionally YCBCR 4:4:4 may be supported.
YCBCR 4:2:2 is also 36-bit mode but does not require the further use
of the Deep Color modes described in section 6.5.2 and 6.5.3.
This means that, even though YUV422 can be used with 12 bit per color,
it shouldn't be treated as a deep color mode.
This deviates from the interpretation of the code and comment, so let's
fix those.
Fixes: d0c94692e0 ("drm/edid: Parse and handle HDMI deep color modes.")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
[ Upstream commit a4d5613c4d ]
When unused memory map is freed the preserved part of the memory map is
extended to match pageblock boundaries because lots of core mm
functionality relies on homogeneity of the memory map within pageblock
boundaries.
Since pfn_valid() is used to check whether there is a valid memory map
entry for a PFN, make it return true also for PFNs that have memory map
entries even if there is no actual memory populated there.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Tested-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/lkml/20210630071211.21011-1-rppt@kernel.org/
Signed-off-by: Mark-PK Tsai <mark-pk.tsai@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f921f53e08 ]
When CONFIG_SPARSEMEM=y the ranges of the memory map that are freed are not
aligned to the pageblock boundaries which breaks assumptions about
homogeneity of the memory map throughout core mm code.
Make sure that the freed memory map is always aligned on pageblock
boundaries regardless of the memory model selection.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/lkml/20210630071211.21011-1-rppt@kernel.org/
[backport upstream modification in mm/memblock.c to arch/arm/mm/init.c]
Signed-off-by: Mark-PK Tsai <mark-pk.tsai@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e2a86800d5 ]
The code that frees unused memory map uses rounds start and end of the
holes that are freed to MAX_ORDER_NR_PAGES to preserve continuity of the
memory map for MAX_ORDER regions.
Lots of core memory management functionality relies on homogeneity of the
memory map within each pageblock which size may differ from MAX_ORDER in
certain configurations.
Although currently, for the architectures that use free_unused_memmap(),
pageblock_order and MAX_ORDER are equivalent, it is cleaner to have common
notation thought mm code.
Replace MAX_ORDER_NR_PAGES with pageblock_nr_pages and update the comments
to make it more clear why the alignment to pageblock boundaries is
required.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/lkml/20210630071211.21011-1-rppt@kernel.org/
[backport upstream modification in mm/memblock.c to arch/arm/mm/init.c]
Signed-off-by: Mark-PK Tsai <mark-pk.tsai@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c29d979260 upstream.
The space allowed for new attributes can be too small if existing header
information is large. That can happen, for example, if there are very
many CPUs, due to having an event ID per CPU per event being stored in the
header information.
Fix by adding the existing header.data_offset. Also increase the extra
space allowed to 8KiB and align to a 4KiB boundary for neatness.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lore.kernel.org/lkml/20211125071457.2066863-1-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
[Adrian: Backport to v5.10]
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dde91ccfa2 upstream.
There is a short period between a net device starts to be unregistered
and when it is actually gone. In that time frame ethtool operations
could still be performed, which might end up in unwanted or undefined
behaviours[1].
Do not allow ethtool operations after a net device starts its
unregistration. This patch targets the netlink part as the ioctl one
isn't affected: the reference to the net device is taken and the
operation is executed within an rtnl lock section and the net device
won't be found after unregister.
[1] For example adding Tx queues after unregister ends up in NULL
pointer exceptions and UaFs, such as:
BUG: KASAN: use-after-free in kobject_get+0x14/0x90
Read of size 1 at addr ffff88801961248c by task ethtool/755
CPU: 0 PID: 755 Comm: ethtool Not tainted 5.15.0-rc6+ #778
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-4.fc34 04/014
Call Trace:
dump_stack_lvl+0x57/0x72
print_address_description.constprop.0+0x1f/0x140
kasan_report.cold+0x7f/0x11b
kobject_get+0x14/0x90
kobject_add_internal+0x3d1/0x450
kobject_init_and_add+0xba/0xf0
netdev_queue_update_kobjects+0xcf/0x200
netif_set_real_num_tx_queues+0xb4/0x310
veth_set_channels+0x1c3/0x550
ethnl_set_channels+0x524/0x610
Fixes: 041b1c5d4a ("ethtool: helper functions for netlink interface")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/20211203101318.435618-1-atenart@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dbd3e6eaf3 upstream.
The removal function is called regardless of whether
/proc/i8k was created successfully or not, the later
causing a WARN() on module removal.
Fix that by only registering the removal function
if /proc/i8k was created successfully.
Tested on a Inspiron 3505.
Fixes: 039ae58503 ("hwmon: Allow to compile dell-smm-hwmon driver without /proc/i8k")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Acked-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20211112171440.59006-1-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c791fe1e2 upstream.
In writeback cache mode mtime/ctime updates are cached, and flushed to the
server using the ->write_inode() callback.
Closing the file will result in a dirty inode being immediately written,
but in other cases the inode can remain dirty after all references are
dropped. This result in the inode being written back from reclaim, which
can deadlock on a regular allocation while the request is being served.
The usual mechanisms (GFP_NOFS/PF_MEMALLOC*) don't work for FUSE, because
serving a request involves unrelated userspace process(es).
Instead do the same as for dirty pages: make sure the inode is written
before the last reference is gone.
- fallocate(2)/copy_file_range(2): these call file_update_time() or
file_modified(), so flush the inode before returning from the call
- unlink(2), link(2) and rename(2): these call fuse_update_ctime(), so
flush the ctime directly from this helper
Reported-by: chenguanyou <chenguanyou@xiaomi.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Cc: Ed Tsai <ed.tsai@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7dd5d437c2 upstream.
In 32-bit architecture, the result of sizeof() is a 32-bit integer so
the expression becomes the multiplication between 2 32-bit integer which
can potentially leads to integer overflow. As a result,
bpf_map_area_alloc() allocates less memory than needed.
Fix this by casting 1 operand to u64.
Fixes: 0d2c4f9640 ("bpf: Eliminate rlimit-based memory accounting for sockmap and sockhash maps")
Fixes: 99c51064fb ("devmap: Use bpf_map_area_alloc() for allocating hash buckets")
Fixes: 546ac1ffb7 ("bpf: add devmap, a map for storing net device references")
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210613143440.71975-1-minhquangbui99@gmail.com
Signed-off-by: Connor O'Brien <connoro@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d445aa402d upstream.
Commit 723de0f917 ("staging: most: remove device from interface
structure") moved registration of driver-provided struct device to
the most subsystem. This updated dim2 driver as well.
However, struct device passed to register_device() becomes refcounted,
and must not be explicitly deallocated, but must provide release method
instead. Which is incompatible with managing it via devres.
This patch makes the device structure allocated without devres, adds
device release method, and moves device destruction there.
Fixes: 723de0f917 ("staging: most: remove device from interface structure")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Link: https://lore.kernel.org/r/20211005143448.8660-2-nikita.yoush@cogentembedded.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3244867af8 upstream.
Do not bail early if there are no bits set in the sparse banks for a
non-sparse, a.k.a. "all CPUs", IPI request. Per the Hyper-V spec, it is
legal to have a variable length of '0', e.g. VP_SET's BankContents in
this case, if the request can be serviced without the extra info.
It is possible that for a given invocation of a hypercall that does
accept variable sized input headers that all the header input fits
entirely within the fixed size header. In such cases the variable sized
input header is zero-sized and the corresponding bits in the hypercall
input should be set to zero.
Bailing early results in KVM failing to send IPIs to all CPUs as expected
by the guest.
Fixes: 214ff83d44 ("KVM: x86: hyperv: implement PV IPI send hypercalls")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20211207220926.718794-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5ceaebcda9 ]
[WHY]
It seems like after a series of plug/unplugs we end up in a situation
where tiled display doesnt support Audio.
[HOW]
The issue seems to be related to when we check streams changed after an
HPD, we should be checking the audio_struct as well to see if any of its
values changed.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Mustapha Ghaddar <mustapha.ghaddar@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02fe0fbd8a ]
In a typical read transfer, start completion flag is being set after
read finishes (notice ipd bit 4 being set):
trasnfer poll=0
i2c start
rk3x-i2c fdd40000.i2c: IRQ: state 1, ipd: 10
i2c read
rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 1b
i2c stop
rk3x-i2c fdd40000.i2c: IRQ: state 4, ipd: 33
This causes I2C transfer being aborted in polled mode from a stop completion
handler:
trasnfer poll=1
i2c start
rk3x-i2c fdd40000.i2c: IRQ: state 1, ipd: 10
i2c read
rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 0
rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 1b
i2c stop
rk3x-i2c fdd40000.i2c: IRQ: state 4, ipd: 13
i2c stop
rk3x-i2c fdd40000.i2c: unexpected irq in STOP: 0x10
Clearing the START flag after read fixes the issue without any obvious
side effects.
This issue was dicovered on RK3566 when adding support for powering
off the RK817 PMIC.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Reviewed-by: John Keeping <john@metanate.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2191b1dfef ]
When link modes were initially added in commit 2c76267943
("net/mlx4_en: Use PTYS register to query ethtool settings") and
later updated for the new ethtool API in commit 3d8f7cc78d
("net: mlx4: use new ETHTOOL_G/SSETTINGS API") the only 1/10G non-baseT
link modes configured were 1000baseKX, 10000baseKX4 and 10000baseKR.
It looks like these got picked to represent other modes since nothing
better was available.
Switch to using more specific link modes added in commit 5711a98221
("net: ethtool: add support for 1000BaseX and missing 10G link modes").
Tested with MCX311A-XCAT connected via DAC.
Before:
% sudo ethtool enp3s0
Settings for enp3s0:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseKX/Full
10000baseKR/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: 1000baseKX/Full
10000baseKR/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 10000Mb/s
Duplex: Full
Auto-negotiation: off
Port: Direct Attach Copper
PHYAD: 0
Transceiver: internal
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000014 (20)
link ifdown
Link detected: yes
With this change:
% sudo ethtool enp3s0
Settings for enp3s0:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseX/Full
10000baseCR/Full
10000baseSR/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: 1000baseX/Full
10000baseCR/Full
10000baseSR/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 10000Mb/s
Duplex: Full
Auto-negotiation: off
Port: Direct Attach Copper
PHYAD: 0
Transceiver: internal
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000014 (20)
link ifdown
Link detected: yes
Tested-by: Michael Stapelberg <michael@stapelberg.ch>
Signed-off-by: Erik Ekman <erik@kryo.se>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e9679738a ]
Revert commit b4b844930f ("tty: serial: fsl_lpuart: drop earlycon entry
for i.MX8QXP"), because this breaks earlycon support on imx8qm/imx8qxp.
While it is true that for earlycon there is no difference between
i.MX8QXP and i.MX7ULP (for now at least), there are differences
regarding clocks and fixups for wakeup support. For that reason it was
deemed unacceptable to add the imx7ulp compatible to device tree in
order to get earlycon working again.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20211124073109.805088-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83bb2c1a01 ]
In order to be able to use primitives such as vcpu_mode_is_32bit(),
we need to synchronize the guest PSTATE. However, this is currently
done deep into the bowels of the world-switch code, and we do have
helpers evaluating this much earlier (__vgic_v3_perform_cpuif_access
and handle_aarch32_guest, for example).
Move the saving of the guest pstate into the early fixups, which
cures the first issue. The second one will be addressed separately.
Tested-by: Fuad Tabba <tabba@google.com>
Reviewed-by: Fuad Tabba <tabba@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
bcm2835_isp_remove is called on an initialisation failure, but at that
point the drvdata hasn't been set. This causes a crash when e.g. using
the cutdown firmware (gpu_mem=16).
Move platform_set_drvdata before the instance probing loop to avoid the
problem.
See: https://github.com/raspberrypi/linux/issues/4774
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
This reverts commit f814bfc5f4.
The commit caused media stalls with kodi and stateful
v4l2 video decode.
John is now using a different way of limiting latency
through stateful v4l2 so this is not required.
Change the maximum sample rate for the amplifier to
192KHz as given in the Infineon specification.
Signed-off-by: Joerg Schambacher <joerg@hifiberry.com>
Parameterise the overlays so that they can have an optional
cam0 parameter to switch to i2c_vc and csi0.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
CM4S follows CM1/3, so based on the documentation cameras/displays
connect to 0/1 and 28/29, not 0/1 and 44/45.
Likewise the camera regulator controls are independent as on CM1/3.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Not all implementations wire up the enable GPIO and may just tie
it to a supply rail.
Make it optional.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Fixing up shutdown GPIOs via overrides is ugly, and doesn't work
on eg CM4 where both cameras share the same shutdown GPIO.
The driver is now updated to use the regulator framework, so switch
to using that instead.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The driver supported using GPIOs to control the shutdown line,
but no regulator control.
Add regulator hooks.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Now that we have regulators and clocks defined in the base DT for
image sensors, switch the overlays to use them.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Unloading regulators through dynamic device tree doesn't work
as the regulators will unregister whilst clients are still
registered. Whilst the regulator framework does WARN when that
happens, the client putting the regulator then typically results
in a NULL dereference and badness.
Instead of creating regulators and clocks from the overlays,
create regulators and clocks for the sensors in the base DT.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The VL805 fetches up to 4 transfer TRBs at a time. TRB reads don't cross
a 64B boundary, and if a TRB is fetched and is not on a 64B boundary,
the read is sized up to the next 64B boundary.
However the VL805 implements a readahead prefetch for TRBs on a transfer
ring. This fetches the next 64B after any TRB read has happened. Near
the end of a ring segment, the prefetcher can read the first 64B of the
next page in physical memory and this is where the behaviour causes a
bug.
The controller does not tag reads with which endpoint they are for, so
if the start of the next page is a ring segment used by a victim
endpoint, and the victim endpoint is about to fetch TRBs from the start
of the segment, the victim endpoint will read from the prefetched data
and not perform a read to main memory. If the data is stale, the ring
cycle state bit may not be correct and the endpoint will silently halt.
Adjust trbs_per_seg for transfer rings allocated for this controller.
See https://github.com/raspberrypi/linux/issues/4685
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
In anticipation of adjusting the number of utilised TRBs in a ring
segment, add trbs_per_seg to struct xhci_ring and use this instead
of a compile-time define.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
commit 9b6164342e upstream.
This document was written a long time ago. Update it.
[1] Drop the version information
The range of the supported GCC versions are always changing. The
current minimal GCC version is 4.9, and commit 1e860048c5
("gcc-plugins: simplify GCC plugin-dev capability test") removed the
old code accordingly.
We do not need to mention specific version ranges like "all gcc versions
from 4.5 to 6.0" since we forget to update the documentation when we
raise the minimal compiler version.
[2] Drop the C compiler statements
Since commit 77342a02ff ("gcc-plugins: drop support for GCC <= 4.7")
the GCC plugin infrastructure only supports g++.
[3] Drop supported architectures
As of v5.11-rc4, the infrastructure supports more architectures;
arm, arm64, mips, powerpc, riscv, s390, um, and x86. (just grep
"select HAVE_GCC_PLUGINS") Again, we miss to update this document when a
new architecture is supported. Let's just say "only some architectures".
[4] Update the apt-get example
We are now discussing to bump the minimal version to GCC 5. The GCC 4.9
support will be removed sooner or later. Change the package example to
gcc-10-plugin-dev while we are here.
[5] Update the build target
Since commit ce2fd53a10 ("kbuild: descend into scripts/gcc-plugins/
via scripts/Makefile"), "make gcc-plugins" is not supported.
"make scripts" builds all the enabled plugins, including some other
tools.
[6] Update the steps for adding a new plugin
At first, all CONFIG options for GCC plugins were located in arch/Kconfig.
After commit 45332b1bdf ("gcc-plugins: split out Kconfig entries to
scripts/gcc-plugins/Kconfig"), scripts/gcc-plugins/Kconfig became the
central place to collect plugin CONFIG options. In my understanding,
this requirement no longer exists because commit 9f671e5815 ("security:
Create "kernel hardening" config area") moved some of plugin CONFIG
options to another file. Find an appropriate place to add the new CONFIG.
The sub-directory support was never used by anyone, and removed by
commit c17d6179ad ("gcc-plugins: remove unused GCC_PLUGIN_SUBDIR").
Remove the useless $(src)/ prefix.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f4c3b83b75 upstream.
With commit 1e860048c5 ("gcc-plugins: simplify GCC plugin-dev
capability test") applied, this hunk can be way simplified because
now scripts/gcc-plugins/Kconfig only checks plugin-version.h
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b560b21f71 upstream.
This commit adds BPF verifier selftests that cover all corner cases by
packet boundary checks. Specifically, 8-byte packet reads are tested at
the beginning of data and at the beginning of data_meta, using all kinds
of boundary checks (all comparison operators: <, >, <=, >=; both
permutations of operands: data + length compared to end, end compared to
data + length). For each case there are three tests:
1. Length is just enough for an 8-byte read. Length is either 7 or 8,
depending on the comparison.
2. Length is increased by 1 - should still pass the verifier. These
cases are useful, because they failed before commit 2fa7d94afc
("bpf: Fix the off-by-two error in range markings").
3. Length is decreased by 1 - should be rejected by the verifier.
Some existing tests are just renamed to avoid duplication.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20211207081521.41923-1-maximmi@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b383a42ca5 upstream.
INVALL CMD specifies that the ITS must ensure any caching associated with
the interrupt collection defined by ICID is consistent with the LPI
configuration tables held in memory for all Redistributors. SYNC is
required to ensure that INVALL is executed.
Currently, LPI configuration data may be inconsistent with that in the
memory within a short period of time after the INVALL command is executed.
Signed-off-by: Wudi Wang <wangwudi@hisilicon.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Fixes: cc2d3216f5 ("irqchip: GICv3: ITS command queue")
Link: https://lore.kernel.org/r/20211208015429.5007-1-zhangshaokun@hisilicon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0a553502e upstream.
irq-armada-370-xp driver already sets MSI_FLAG_MULTI_PCI_MSI flag into
msi_domain_info structure. But allocated interrupt numbers for Multi-MSI
needs to be properly aligned otherwise devices send MSI interrupt with
wrong number.
Fix this issue by using function bitmap_find_free_region() instead of
bitmap_find_next_zero_area() to allocate aligned interrupt numbers.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: a71b9412c9 ("irqchip/armada-370-xp: Allow allocation of multiple MSIs")
Cc: stable@vger.kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211125130057.26705-2-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6661146427 upstream.
IIO trigger handlers must call iio_trigger_notify_done() when done. This
must be done even when an error occurred. Otherwise the trigger will be
seen as busy indefinitely and the trigger handler will never be called
again.
The ad7768-1 driver neglects to call iio_trigger_notify_done() when there
is an error reading the converter data. Fix this by making sure that
iio_trigger_notify_done() is included in the error exit path.
Fixes: a5f8c7da3d ("iio: adc: Add AD7768-1 ADC basic support")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211101144055.13858-2-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92beafb76a upstream.
Both the charging and discharging currents on AXP22x are stored as
12-bit integers, in accordance with the datasheet.
It's also confirmed by vendor BSP (axp20x_adc.c:axp22_icharge_to_mA).
The scale factor of 0.5 is never mentioned in datasheet, nor in the
vendor source code. I think it was here to compensate for
erroneous addition bit in register width.
Tested on custom A40i+AXP221s board with external ammeter as
a reference.
Fixes: 0e34d5de96 ("iio: adc: add support for X-Powers AXP20X and AXP22X PMICs ADCs")
Signed-off-by: Evgeny Boger <boger@wirenboard.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20211116213746.264378-1-boger@wirenboard.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f711f28e71 upstream.
Some I/Os are connected to ADC input channels, when the corresponding bit
in PCSEL register are set on STM32H7 and STM32MP15. This is done in the
prepare routine of stm32-adc driver.
There are constraints here, as PCSEL shouldn't be set when VDDA supply
is disabled. Enabling/disabling of VDDA supply in done via stm32-adc-core
runtime PM routines (before/after ADC is enabled/disabled).
Currently, PCSEL remains set when disabling ADC. Later on, PM runtime
can disable the VDDA supply. This creates some conditions on I/Os that
can start to leak current.
So PCSEL needs to be cleared when disabling the ADC.
Fixes: 95e339b6e8 ("iio: adc: stm32: add support for STM32H7")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Reviewed-by: Olivier Moysan <olivier.moysan@foss.st.com>
Link: https://lore.kernel.org/r/1634905169-23762-1-git-send-email-fabrice.gasnier@foss.st.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67fe29583e upstream.
IIO trigger handlers must call iio_trigger_notify_done() when done. This
must be done even when an error occurred. Otherwise the trigger will be
seen as busy indefinitely and the trigger handler will never be called
again.
The itg3200 driver neglects to call iio_trigger_notify_done() when there is
an error reading the gyro data. Fix this by making sure that
iio_trigger_notify_done() is included in the error exit path.
Fixes: 9dbf091da0 ("iio: gyro: Add itg3200")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211101144055.13858-1-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45febe0d63 upstream.
IIO trigger handlers need to return one of the irqreturn_t values.
Returning an error code is not supported.
The kxsd9 interrupt handler returns an error code if reading the data
registers fails. In addition when exiting due to an error the trigger
handler does not call `iio_trigger_notify_done()`. Which when not done
keeps the triggered disabled forever.
Modify the code so that the function returns a valid irqreturn_t value as
well as calling `iio_trigger_notify_done()` on all exit paths.
Since we can't return the error code make sure to at least log it as part
of the error message.
Fixes: 0427a106a9 ("iio: accel: kxsd9: Add triggered buffer handling")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20211024171251.22896-2-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef9d67fa72 upstream.
IIO trigger handlers need to return one of the irqreturn_t values.
Returning an error code is not supported.
The ltr501 interrupt handler gets this right for most error paths, but
there is one case where it returns the error code.
In addition for this particular case the trigger handler does not call
`iio_trigger_notify_done()`. Which when not done keeps the triggered
disabled forever.
Modify the code so that the function returns a valid irqreturn_t value as
well as calling `iio_trigger_notify_done()` on all exit paths.
Fixes: 2690be9051 ("iio: Add Lite-On ltr501 ambient light / proximity sensor driver")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211024171251.22896-1-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd00822357 upstream.
The mma8452 driver directly assigns a trigger to the struct iio_dev. The
IIO core when done using this trigger will call `iio_trigger_put()` to drop
the reference count by 1.
Without the matching `iio_trigger_get()` in the driver the reference count
can reach 0 too early, the trigger gets freed while still in use and a
use-after-free occurs.
Fix this by getting a reference to the trigger before assigning it to the
IIO device.
Fixes: ae6d9ce056 ("iio: mma8452: Add support for interrupt driven triggers.")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211024092700.6844-1-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a827a49846 upstream.
In viio_trigger_alloc() device_initialize() is used to set the initial
reference count of the trigger to 1. Then another get_device() is called on
trigger. This sets the reference count to 2 before the trigger is returned.
iio_trigger_free(), which is the matching API to viio_trigger_alloc(),
calls put_device() which decreases the reference count by 1. But the second
reference count acquired in viio_trigger_alloc() is never dropped.
As a result the iio_trigger_release() function is never called and the
memory associated with the trigger is never freed.
Since there is no reason for the trigger to start its lifetime with two
reference counts just remove the extra get_device() in
viio_trigger_alloc().
Fixes: 5f9c035cae ("staging:iio:triggers. Add a reference get to the core for triggers.")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20211024092700.6844-2-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7faac1953e upstream.
Make xhci_disable_slot() synchronous, thus ensuring it, and
xhci_free_dev() calling it return after xHC controller completes
the disable slot command.
Otherwise the roothub and xHC host may runtime suspend, and clear the
command ring while the disable slot command is being processed.
This causes a command completion mismatch as the completion event can't
be mapped to the correct command.
Command ring gets out of sync and commands time out.
Driver finally assumes host is unresponsive and bails out.
usb 2-4: USB disconnect, device number 10
xhci_hcd 0000:00:0d.0: ERROR mismatched command completion event
...
xhci_hcd 0000:00:0d.0: xHCI host controller not responding, assume dead
xhci_hcd 0000:00:0d.0: HC died; cleaning up
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211210141735.1384209-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 811ae81320 upstream.
When the xHCI is quirked with XHCI_RESET_ON_RESUME, runtime resume
routine also resets the controller.
This is bad for USB drivers without reset_resume callback, because
there's no subsequent call of usb_dev_complete() ->
usb_resume_complete() to force rebinding the driver to the device. For
instance, btusb device stops working after xHCI controller is runtime
resumed, if the controlled is quirked with XHCI_RESET_ON_RESUME.
So always take XHCI_RESET_ON_RESUME into account to solve the issue.
Cc: <stable@vger.kernel.org>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211210141735.1384209-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 86ebbc11bb upstream.
Under some conditions, USB gadget devices can show allocated buffer
contents to a host. Fix this up by zero-allocating them so that any
extra data will all just be zeros.
Reported-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Tested-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 153a2d7e33 upstream.
Sometimes USB hosts can ask for buffers that are too large from endpoint
0, which should not be allowed. If this happens for OUT requests, stall
the endpoint, but for IN requests, trim the request size to the endpoint
buffer size.
Co-developed-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f6071e5e39 upstream.
Currently rp_filter tests in fib_tests.sh:fib_rp_filter_test() are
failing. ping sockets are bound to dummy1 using the "-I" option
(SO_BINDTODEVICE), but socket lookup is failing when receiving ping
replies, since the routing table thinks they belong to dummy0.
For example, suppose ping is using a SOCK_RAW socket for ICMP messages.
When receiving ping replies, in __raw_v4_lookup(), sk->sk_bound_dev_if
is 3 (dummy1), but dif (skb_rtable(skb)->rt_iif) says 2 (dummy0), so the
raw_sk_bound_dev_eq() check fails. Similar things happen in
ping_lookup() for SOCK_DGRAM sockets.
These tests used to pass due to a bug [1] in iputils, where "ping -I"
actually did not bind ICMP message sockets to device. The bug has been
fixed by iputils commit f455fee41c07 ("ping: also bind the ICMP socket
to the specific device") in 2016, which is why our rp_filter tests
started to fail. See [2] .
Fixing the tests while keeping everything in one netns turns out to be
nontrivial. Rework the tests and build the following topology:
┌─────────────────────────────┐ ┌─────────────────────────────┐
│ network namespace 1 (ns1) │ │ network namespace 2 (ns2) │
│ │ │ │
│ ┌────┐ ┌─────┐ │ │ ┌─────┐ ┌────┐ │
│ │ lo │<───>│veth1│<────────┼────┼─>│veth2│<──────────>│ lo │ │
│ └────┘ ├─────┴──────┐ │ │ ├─────┴──────┐ └────┘ │
│ │192.0.2.1/24│ │ │ │192.0.2.1/24│ │
│ └────────────┘ │ │ └────────────┘ │
└─────────────────────────────┘ └─────────────────────────────┘
Consider sending an ICMP_ECHO packet A in ns2. Both source and
destination IP addresses are 192.0.2.1, and we use strict mode rp_filter
in both ns1 and ns2:
1. A is routed to lo since its destination IP address is one of ns2's
local addresses (veth2);
2. A is redirected from lo's egress to veth2's egress using mirred;
3. A arrives at veth1's ingress in ns1;
4. A is redirected from veth1's ingress to lo's ingress, again, using
mirred;
5. In __fib_validate_source(), fib_info_nh_uses_dev() returns false,
since A was received on lo, but reverse path lookup says veth1;
6. However A is not dropped since we have relaxed this check for lo in
commit 66f8209547 ("fib: relax source validation check for loopback
packets");
Making sure A is not dropped here in this corner case is the whole point
of having this test.
7. As A reaches the ICMP layer, an ICMP_ECHOREPLY packet, B, is
generated;
8. Similarly, B is redirected from lo's egress to veth1's egress (in
ns1), then redirected once again from veth2's ingress to lo's
ingress (in ns2), using mirred.
Also test "ping 127.0.0.1" from ns2. It does not trigger the relaxed
check in __fib_validate_source(), but just to make sure the topology
works with loopback addresses.
Tested with ping from iputils 20210722-41-gf9fb573:
$ ./fib_tests.sh -t rp_filter
IPv4 rp_filter tests
TEST: rp_filter passes local packets [ OK ]
TEST: rp_filter passes loopback packets [ OK ]
[1] https://github.com/iputils/iputils/issues/55
[2] f455fee41c
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Fixes: adb701d6cf ("selftests: add a test case for rp_filter")
Reviewed-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Peilin Ye <peilin.ye@bytedance.com>
Acked-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20211201004720.6357-1-yepeilin.cs@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d17b9737c2 upstream.
The ql_wait_for_drvr_lock() fails and returns false, then this
function should return an error code instead of returning success.
The other problem is that the success path prints an error message
netdev_err(ndev, "Releasing driver lock\n"); Delete that and
re-order the code a little to make it more clear.
Fixes: 5a4faa8737 ("[PATCH] qla3xxx NIC driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211207082416.GA16110@kili
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5bd95d171 upstream.
Background:
We have a customer is running a Profinet stack on the 8MM which receives and
responds PNIO packets every 4ms and PNIO-CM packets every 40ms. However, from
time to time the received PNIO-CM package is "stock" and is only handled when
receiving a new PNIO-CM or DCERPC-Ping packet (tcpdump shows the PNIO-CM and
the DCERPC-Ping packet at the same time but the PNIO-CM HW timestamp is from
the expected 40 ms and not the 2s delay of the DCERPC-Ping).
After debugging, we noticed PNIO, PNIO-CM and DCERPC-Ping packets would
be handled by different RX queues.
The root cause should be driver ack all queues' interrupt when handle a
specific queue in fec_enet_rx_queue(). The blamed patch is introduced to
receive as much packets as possible once to avoid interrupt flooding.
But it's unreasonable to clear other queues'interrupt when handling one
queue, this patch tries to fix it.
Fixes: ed63f1dcd5 (net: fec: clear receive interrupts before processing a packet)
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Reported-by: Nicolas Diaz <nicolas.diaz@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20211206135457.15946-1-qiangqing.zhang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit badd7857f5 upstream.
There are two error paths which accidentally return success instead of
a negative error code.
Fixes: bbd2190ce9 ("Altera TSE: Add main and header file for Altera Ethernet Driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2be6d4d16a upstream.
Currently, due to the sequential use of min_t() and clamp_t() macros,
in cdc_ncm_check_tx_max(), if dwNtbOutMaxSize is not set, the logic
sets tx_max to 0. This is then used to allocate the data area of the
SKB requested later in cdc_ncm_fill_tx_frame().
This does not cause an issue presently because when memory is
allocated during initialisation phase of SKB creation, more memory
(512b) is allocated than is required for the SKB headers alone (320b),
leaving some space (512b - 320b = 192b) for CDC data (172b).
However, if more elements (for example 3 x u64 = [24b]) were added to
one of the SKB header structs, say 'struct skb_shared_info',
increasing its original size (320b [320b aligned]) to something larger
(344b [384b aligned]), then suddenly the CDC data (172b) no longer
fits in the spare SKB data area (512b - 384b = 128b).
Consequently the SKB bounds checking semantics fails and panics:
skbuff: skb_over_panic: text:ffffffff830a5b5f len:184 put:172 \
head:ffff888119227c00 data:ffff888119227c00 tail:0xb8 end:0x80 dev:<NULL>
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:110!
RIP: 0010:skb_panic+0x14f/0x160 net/core/skbuff.c:106
<snip>
Call Trace:
<IRQ>
skb_over_panic+0x2c/0x30 net/core/skbuff.c:115
skb_put+0x205/0x210 net/core/skbuff.c:1877
skb_put_zero include/linux/skbuff.h:2270 [inline]
cdc_ncm_ndp16 drivers/net/usb/cdc_ncm.c:1116 [inline]
cdc_ncm_fill_tx_frame+0x127f/0x3d50 drivers/net/usb/cdc_ncm.c:1293
cdc_ncm_tx_fixup+0x98/0xf0 drivers/net/usb/cdc_ncm.c:1514
By overriding the max value with the default CDC_NCM_NTB_MAX_SIZE_TX
when not offered through the system provided params, we ensure enough
data space is allocated to handle the CDC data, meaning no crash will
occur.
Cc: Oliver Neukum <oliver@neukum.org>
Fixes: 289507d336 ("net: cdc_ncm: use sysfs for rx/tx aggregation tuning")
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Link: https://lore.kernel.org/r/20211202143437.1411410-1-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d1d57debe upstream.
Since 66dfdff03d ("perf tools: Add Python 3 support") we don't use
the tools/build/feature/test-libpython-version.c version in any Makefile
feature check:
$ find tools/ -type f | xargs grep feature-libpython-version
$
The only place where this was used was removed in 66dfdff03d:
- ifneq ($(feature-libpython-version), 1)
- $(warning Python 3 is not yet supported; please set)
- $(warning PYTHON and/or PYTHON_CONFIG appropriately.)
- $(warning If you also have Python 2 installed, then)
- $(warning try something like:)
- $(warning $(and ,))
- $(warning $(and ,) make PYTHON=python2)
- $(warning $(and ,))
- $(warning Otherwise, disable Python support entirely:)
- $(warning $(and ,))
- $(warning $(and ,) make NO_LIBPYTHON=1)
- $(warning $(and ,))
- $(error $(and ,))
- else
- LDFLAGS += $(PYTHON_EMBED_LDFLAGS)
- EXTLIBS += $(PYTHON_EMBED_LIBADD)
- LANG_BINDINGS += $(obj-perf)python/perf.so
- $(call detected,CONFIG_LIBPYTHON)
- endif
And nowadays we either build with PYTHON=python3 or just install the
python3 devel packages and perf will build against it.
But the leftover feature-libpython-version check made the fast path
feature detection to break in all cases except when python2 devel files
were installed:
$ rpm -qa | grep python.*devel
python3-devel-3.9.7-1.fc34.x86_64
$ rm -rf /tmp/build/perf ; mkdir -p /tmp/build/perf ;
$ make -C tools/perf O=/tmp/build/perf install-bin
make: Entering directory '/var/home/acme/git/perf/tools/perf'
BUILD: Doing 'make -j32' parallel build
HOSTCC /tmp/build/perf/fixdep.o
<SNIP>
$ cat /tmp/build/perf/feature/test-all.make.output
In file included from test-all.c:18:
test-libpython-version.c:5:10: error: #error
5 | #error
| ^~~~~
$ ldd ~/bin/perf | grep python
libpython3.9.so.1.0 => /lib64/libpython3.9.so.1.0 (0x00007fda6dbcf000)
$
As python3 is the norm these days, fix this by just removing the unused
feature-libpython-version feature check, making the test-all fast path
to work with the common case.
With this:
$ rm -rf /tmp/build/perf ; mkdir -p /tmp/build/perf ;
$ make -C tools/perf O=/tmp/build/perf install-bin |& head
make: Entering directory '/var/home/acme/git/perf/tools/perf'
BUILD: Doing 'make -j32' parallel build
HOSTCC /tmp/build/perf/fixdep.o
HOSTLD /tmp/build/perf/fixdep-in.o
LINK /tmp/build/perf/fixdep
Auto-detecting system features:
... dwarf: [ on ]
... dwarf_getlocations: [ on ]
... glibc: [ on ]
$ ldd ~/bin/perf | grep python
libpython3.9.so.1.0 => /lib64/libpython3.9.so.1.0 (0x00007f58800b0000)
$ cat /tmp/build/perf/feature/test-all.make.output
$
Reviewed-by: James Clark <james.clark@arm.com>
Fixes: 66dfdff03d ("perf tools: Add Python 3 support")
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jaroslav Škarvada <jskarvad@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: https://lore.kernel.org/lkml/YaYmeeC6CS2b8OSz@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 96db48c9d7 upstream.
This binding was already documented in phy.txt, commit 252ae5330d
("Documentation: devicetree: Add PHY no lane swap binding"), but got
accidently removed during YAML conversion in commit d8704342c1
("dt-bindings: net: Add a YAML schemas for the generic PHY options").
Note: 'enet-phy-lane-no-swap' and the absence of 'enet-phy-lane-swap' are
not identical, as the former one disable this feature, while the latter
one doesn't change anything.
Fixes: d8704342c1 ("dt-bindings: net: Add a YAML schemas for the generic PHY options")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20211130082756.713919-1-alexander.stein@ew.tq-group.com
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6a631c0432 upstream.
The initial implementation of migrate_disable() for mainline was a
wrapper around preempt_disable(). RT kernels substituted this with
a real migrate disable implementation.
Later on mainline gained true migrate disable support, but the
documentation was not updated.
Update the documentation, remove the claims about migrate_disable()
mapping to preempt_disable() on non-PREEMPT_RT kernels.
Fixes: 74d862b682 ("sched: Make migrate_disable/enable() independent of RT")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20211127163200.10466-2-bigeasy@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39bd54d43b upstream.
This reverts commit 239edf686c.
239edf686c ("PCI: aardvark: Fix support for PCI_ROM_ADDRESS1 on emulated
bridge") added support for the Type 1 Expansion ROM BAR at config offset
0x38, based on the register being listed in the Marvell Armada A3720 spec.
But the spec doesn't document it at all for RC mode, and there is no ROM in
the SOC, so remove this emulation for now.
The PCI bridge which represents aardvark's PCIe Root Port has an Expansion
ROM Base Address register at offset 0x30, but its meaning is different than
PCI's Expansion ROM BAR register, although the layout is the same. (This
is why we thought it does the same thing.)
First: there is no ROM (or part of BootROM) in the A3720 SOC dedicated for
PCIe Root Port (or controller in RC mode) containing executable code that
would initialize the Root Port, suitable for execution in bootloader (this
is how Expansion ROM BAR is used on x86).
Second: in A3720 spec the register (address 0xD0070030) is not documented
at all for Root Complex mode, but similar to other BAR registers, it has an
"entangled partner" in register 0xD0075920, which does address translation
for the BAR in 0xD0070030:
- the BAR register sets the address from the view of PCIe bus
- the translation register sets the address from the view of the CPU
The other BAR registers also have this entangled partner, and they can be
used to:
- in RC mode: address-checking on the receive side of the RC (they can
define address ranges for memory accesses from remote Endpoints to the
RC)
- in Endpoint mode: allow the remote CPU to access memory on A3720
The Expansion ROM BAR has only the Endpoint part documented, but from the
similarities we think that it can also be used in RC mode in that way.
So either Expansion ROM BAR has different meaning (if the hypothesis above
is true), or we don't know it's meaning (since it is not documented for RC
mode).
Remove the register from the emulated bridge accessing functions.
[bhelgaas: summarize reason for removal (first paragraph)]
Fixes: 239edf686c ("PCI: aardvark: Fix support for PCI_ROM_ADDRESS1 on emulated bridge")
Link: https://lore.kernel.org/r/20211125160148.26029-3-kabel@kernel.org
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9472335eaa upstream.
Under certain circumstances, the timing settings calculated by
the FSMC NAND controller driver were inaccurate.
These settings led to incorrect data reads or fallback to
timing mode 0 depending on the NAND chip used.
The timing computation did not take into account the following
constraint given in SPEAr3xx reference manual:
twait >= tCEA - (tset * TCLK) + TOUTDEL + TINDEL
Enhance the timings calculation by taking into account this
additional constraint.
This change has no impact on slow timing modes such as mode 0.
Indeed, on mode 0, computed values are the same with and
without the patch.
NANDs which previously stayed in mode 0 because of fallback to
mode 0 can now work at higher speeds and NANDs which were not
working at all because of the corrupted data work at high
speeds without troubles.
Overall improvement on a Micron/MT29F1G08 (flash_speed tool):
mode0 mode3
eraseblock write speed 3220 KiB/s 4511 KiB/s
eraseblock read speed 4491 KiB/s 7529 KiB/s
Fixes: d9fb079571 ("mtd: nand: fsmc: add support for SDR timings")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211119150316.43080-5-herve.codina@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8aa55ab422 upstream.
After setting pre-set combined to 16 queues and reserving 16 queues by
tc qdisc, pre-set maximum combined queues returned to default value
after VF reset being 4 and this generated errors during removing tc.
Fixed by removing clear num_req_queues before reset VF.
Fixes: e284fc2804 (i40e: Add and delete cloud filter)
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Bindushree P <Bindushree.p@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61125b8be8 upstream.
Fix failed operation code appearing if handling messages from VF.
Implemented by waiting for VF appropriate state if request starts
handle while VF reset.
Without this patch the message handling request while VF is in
a reset state ends with error -5 (I40E_ERR_PARAM).
Fixes: 5c3c48ac6b ("i40e: implement virtual device interface")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b0969f8389 upstream.
When hns_roce_v2_destroy_qp() is called, the brief calling process of the
driver is as follows:
......
hns_roce_v2_destroy_qp
hns_roce_v2_qp_modify
hns_roce_cmd_mbox
hns_roce_qp_destroy
If hns_roce_cmd_mbox() detects that the hardware is being reset during the
execution of the hns_roce_cmd_mbox(), the driver will not be able to get
the return value from the hardware (the firmware cannot respond to the
driver's mailbox during the hardware reset phase).
The driver needs to wait for the hardware reset to complete before
continuing to execute hns_roce_qp_destroy(), otherwise it may happen that
the driver releases the resources but the hardware is still accessing. In
order to fix this problem, HNS RoCE needs to add a piece of code to wait
for the hardware reset to complete.
The original interface get_hw_reset_stat() is the instantaneous state of
the hardware reset, which cannot accurately reflect whether the hardware
reset is completed, so it needs to be replaced with the ae_dev_reset_cnt
interface.
The sign that the hardware reset is complete is that the return value of
the ae_dev_reset_cnt interface is greater than the original value
reset_cnt recorded by the driver.
Fixes: 6a04aed6af ("RDMA/hns: Fix the chip hanging caused by sending mailbox&CMQ during reset")
Link: https://lore.kernel.org/r/20211123142402.26936-1-liangwenpeng@huawei.com
Signed-off-by: Yangyang Li <liyangyang20@huawei.com>
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52414e27d6 upstream.
is_reset is used to indicate whether the hardware starts to reset. When
hns_roce_hw_v2_reset_notify_down() is called, the hardware has not yet
started to reset. If is_reset is set at this time, all mailbox operations
of resource destroy actions will be intercepted by driver. When the driver
cleans up resources, but the hardware is still accessed, the following
errors will appear:
arm-smmu-v3 arm-smmu-v3.2.auto: event 0x10 received:
arm-smmu-v3 arm-smmu-v3.2.auto: 0x0000350100000010
arm-smmu-v3 arm-smmu-v3.2.auto: 0x000002088000003f
arm-smmu-v3 arm-smmu-v3.2.auto: 0x00000000a50e0800
arm-smmu-v3 arm-smmu-v3.2.auto: 0x0000000000000000
arm-smmu-v3 arm-smmu-v3.2.auto: event 0x10 received:
arm-smmu-v3 arm-smmu-v3.2.auto: 0x0000350100000010
arm-smmu-v3 arm-smmu-v3.2.auto: 0x000002088000043e
arm-smmu-v3 arm-smmu-v3.2.auto: 0x00000000a50a0800
arm-smmu-v3 arm-smmu-v3.2.auto: 0x0000000000000000
arm-smmu-v3 arm-smmu-v3.2.auto: event 0x10 received:
arm-smmu-v3 arm-smmu-v3.2.auto: 0x0000350100000010
arm-smmu-v3 arm-smmu-v3.2.auto: 0x0000020880000436
arm-smmu-v3 arm-smmu-v3.2.auto: 0x00000000a50a0880
arm-smmu-v3 arm-smmu-v3.2.auto: 0x0000000000000000
arm-smmu-v3 arm-smmu-v3.2.auto: event 0x10 received:
arm-smmu-v3 arm-smmu-v3.2.auto: 0x0000350100000010
arm-smmu-v3 arm-smmu-v3.2.auto: 0x000002088000043a
arm-smmu-v3 arm-smmu-v3.2.auto: 0x00000000a50e0840
hns3 0000:35:00.0: INT status: CMDQ(0x0) HW errors(0x0) other(0x0)
arm-smmu-v3 arm-smmu-v3.2.auto: 0x0000000000000000
hns3 0000:35:00.0: received unknown or unhandled event of vector0
arm-smmu-v3 arm-smmu-v3.2.auto: event 0x10 received:
arm-smmu-v3 arm-smmu-v3.2.auto: 0x0000350100000010
{34}[Hardware Error]: Hardware error from APEI Generic Hardware Error Source: 7
is_reset will be set correctly in check_aedev_reset_status(), so the
setting in hns_roce_hw_v2_reset_notify_down() should be deleted.
Fixes: 726be12f5c ("RDMA/hns: Set reset flag when hw resetting")
Link: https://lore.kernel.org/r/20211123084809.37318-1-liangwenpeng@huawei.com
Signed-off-by: Yangyang Li <liyangyang20@huawei.com>
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23ba28616d upstream.
Currently each channel is added as list to dai channel list, however
there is danger of adding same channel to multiple dai channel list
which endups corrupting the other list where its already added.
This patch ensures that the channel is actually free before adding to
the dai channel list and also ensures that the channel is on the list
before deleting it.
This check was missing previously, and we did not hit this issue as
we were testing very simple usecases with sequence of amixer commands.
Fixes: a70d924575 ("ASoC: wcd934x: add capture dapm widgets")
Fixes: dd9eb19b56 ("ASoC: wcd934x: add playback dapm widgets")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20211130160507.22180-2-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4739d88ad8 upstream.
msm_routing_put_audio_mixer() can return incorrect value in various scenarios.
scenario 1:
amixer cset iface=MIXER,name='SLIMBUS_0_RX Audio Mixer MultiMedia1' 1
amixer cset iface=MIXER,name='SLIMBUS_0_RX Audio Mixer MultiMedia1' 0
return value is 0 instead of 1 eventhough value was changed
scenario 2:
amixer cset iface=MIXER,name='SLIMBUS_0_RX Audio Mixer MultiMedia1' 1
amixer cset iface=MIXER,name='SLIMBUS_0_RX Audio Mixer MultiMedia1' 1
return value is 1 instead of 0 eventhough the value was not changed
scenario 3:
amixer cset iface=MIXER,name='SLIMBUS_0_RX Audio Mixer MultiMedia1' 0
return value is 1 instead of 0 eventhough the value was not changed
Fix this by adding checks, so that change notifications are sent correctly.
Fixes: e3a33673e8 ("ASoC: qdsp6: q6routing: Add q6routing driver")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20211130163110.5628-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 444dd878e8 upstream.
The kerneldoc comment of pm_runtime_active() does not reflect the
behavior of the function, so update it accordingly.
Fixes: 403d2d116e ("PM: runtime: Add kerneldoc comments to multiple helpers")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e227b198a upstream.
Although it is unlikely that stack could transmit a non LSO
skb with length > MTU, however in some cases or environment such
occurrences actually resulted into firmware asserts due to packet
length being greater than the max supported by the device (~9700B).
This patch adds the safeguard for such odd cases to avoid firmware
asserts.
v2: Added "Fixes" tag with one of the initial driver commit
which enabled the TX traffic actually (as this was probably
day1 issue which was discovered recently by some customer
environment)
Fixes: a2ec6172d2 ("qede: Add support for link")
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Link: https://lore.kernel.org/r/20211203174413.13090-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7db0e0c819 upstream.
According to ZBC and SPC specifications, the unit of ALLOCATION LENGTH
field of REPORT ZONES command is byte. However, current scsi_debug
implementation handles it as number of zones to calculate buffer size to
report zones. When the ALLOCATION LENGTH has a large number, this results
in too large buffer size and causes memory allocation failure. Fix the
failure by handling ALLOCATION LENGTH as byte unit.
Link: https://lore.kernel.org/r/20211207010638.124280-1-shinichiro.kawasaki@wdc.com
Fixes: f0d1cf9378 ("scsi: scsi_debug: Add ZBC zone commands")
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6539262057 upstream.
Calling scsi_remove_host() before scsi_add_host() results in a crash:
BUG: kernel NULL pointer dereference, address: 0000000000000108
RIP: 0010:device_del+0x63/0x440
Call Trace:
device_unregister+0x17/0x60
scsi_remove_host+0xee/0x2a0
pm8001_pci_probe+0x6ef/0x1b90 [pm80xx]
local_pci_probe+0x3f/0x90
We cannot call scsi_remove_host() in pm8001_alloc() because scsi_add_host()
has not been called yet at that point in time.
Function call tree:
pm8001_pci_probe()
|
`- pm8001_pci_alloc()
| |
| `- pm8001_alloc()
| |
| `- scsi_remove_host()
|
`- scsi_add_host()
Link: https://lore.kernel.org/r/20211201041627.1592487-1-ipylypiv@google.com
Fixes: 05c6c029a4 ("scsi: pm80xx: Increase number of supported queues")
Reviewed-by: Vishakha Channapattan <vishakhavc@google.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 48b27b6b51 upstream.
As people have been asking to allow non-root processes to have access to
the tracefs directory, it was considered best to only allow groups to have
access to the directory, where it is easier to just set the tracefs file
system to a specific group (as other would be too dangerous), and that way
the admins could pick which processes would have access to tracefs.
Unfortunately, this broke tooling on Android that expected the other bit
to be set. For some special cases, for non-root tools to trace the system,
tracefs would be mounted and change the permissions of the top level
directory which gave access to all running tasks permission to the
tracing directory. Even though this would be dangerous to do in a
production environment, for testing environments this can be useful.
Now with the new changes to not allow other (which is still the proper
thing to do), it breaks the testing tooling. Now more code needs to be
loaded on the system to change ownership of the tracing directory.
The real solution is to have tracefs honor the gid=xxx option when
mounting. That is,
(tracing group tracing has value 1003)
mount -t tracefs -o gid=1003 tracefs /sys/kernel/tracing
should have it that all files in the tracing directory should be of the
given group.
Copy the logic from d_walk() from dcache.c and simplify it for the mount
case of tracefs if gid is set. All the files in tracefs will be walked and
their group will be set to the value passed in.
Link: https://lkml.kernel.org/r/20211207171729.2a54e1b3@gandalf.local.home
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-fsdevel@vger.kernel.org
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reported-by: Kalesh Singh <kaleshsingh@google.com>
Reported-by: Yabin Cui <yabinc@google.com>
Fixes: 49d67e4457 ("tracefs: Have tracefs directories not set OTH permission bits by default")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a50e659b2a upstream.
The registration of XDP queue information is incorrect because the
RX queue id we use is invalid. When port->id == 0 it appears to works
as expected yet it's no longer the case when port->id != 0.
The problem arised while using a recent kernel version on the
MACCHIATOBin. This board has several ports:
* eth0 and eth1 are 10Gbps interfaces ; both ports has port->id == 0;
* eth2 is a 1Gbps interface with port->id != 0.
Code from xdp-tutorial (more specifically advanced03-AF_XDP) was used
to test packet capture and injection on all these interfaces. The XDP
kernel was simplified to:
SEC("xdp_sock")
int xdp_sock_prog(struct xdp_md *ctx)
{
int index = ctx->rx_queue_index;
/* A set entry here means that the correspnding queue_id
* has an active AF_XDP socket bound to it. */
if (bpf_map_lookup_elem(&xsks_map, &index))
return bpf_redirect_map(&xsks_map, index, 0);
return XDP_PASS;
}
Starting the program using:
./af_xdp_user -d DEV
Gives the following result:
* eth0 : ok
* eth1 : ok
* eth2 : no capture, no injection
Investigating the issue shows that XDP rx queues for eth2 are wrong:
XDP expects their id to be in the range [0..3] but we found them to be
in the range [32..35].
Trying to force rx queue ids using:
./af_xdp_user -d eth2 -Q 32
fails as expected (we shall not have more than 4 queues).
When we register the XDP rx queue information (using
xdp_rxq_info_reg() in function mvpp2_rxq_init()) we tell it to use
rxq->id as the queue id. This value is computed as:
rxq->id = port->id * max_rxq_count + queue_id
where max_rxq_count depends on the device version. In the MACCHIATOBin
case, this value is 32, meaning that rx queues on eth2 are numbered
from 32 to 35 - there are four of them.
Clearly, this is not the per-port queue id that XDP is expecting:
it wants a value in the range [0..3]. It shall directly use queue_id
which is stored in rxq->logic_rxq -- so let's use that value instead.
rxq->id is left untouched ; its value is indeed valid but it should
not be used in this context.
This is consistent with the remaining part of the code in
mvpp2_rxq_init().
With this change, packet capture is working as expected on all the
MACCHIATOBin ports.
Fixes: b27db2274b ("mvpp2: use page_pool allocator")
Signed-off-by: Louis Amas <louis.amas@eho.link>
Signed-off-by: Emmanuel Deloget <emmanuel.deloget@eho.link>
Reviewed-by: Marcin Wojtas <mw@semihalf.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/r/20211207143423.916334-1-louis.amas@eho.link
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 50252e4b5e upstream.
signalfd_poll() and binder_poll() are special in that they use a
waitqueue whose lifetime is the current task, rather than the struct
file as is normally the case. This is okay for blocking polls, since a
blocking poll occurs within one task; however, non-blocking polls
require another solution. This solution is for the queue to be cleared
before it is freed, by sending a POLLFREE notification to all waiters.
Unfortunately, only eventpoll handles POLLFREE. A second type of
non-blocking poll, aio poll, was added in kernel v4.18, and it doesn't
handle POLLFREE. This allows a use-after-free to occur if a signalfd or
binder fd is polled with aio poll, and the waitqueue gets freed.
Fix this by making aio poll handle POLLFREE.
A patch by Ramji Jiyani <ramjiyani@google.com>
(https://lore.kernel.org/r/20211027011834.2497484-1-ramjiyani@google.com)
tried to do this by making aio_poll_wake() always complete the request
inline if POLLFREE is seen. However, that solution had two bugs.
First, it introduced a deadlock, as it unconditionally locked the aio
context while holding the waitqueue lock, which inverts the normal
locking order. Second, it didn't consider that POLLFREE notifications
are missed while the request has been temporarily de-queued.
The second problem was solved by my previous patch. This patch then
properly fixes the use-after-free by handling POLLFREE in a
deadlock-free way. It does this by taking advantage of the fact that
freeing of the waitqueue is RCU-delayed, similar to what eventpoll does.
Fixes: 2c14fa838c ("aio: implement IOCB_CMD_POLL")
Cc: <stable@vger.kernel.org> # v4.18+
Link: https://lore.kernel.org/r/20211209010455.42744-6-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 363bee27e2 upstream.
Currently, aio_poll_wake() will always remove the poll request from the
waitqueue. Then, if aio_poll_complete_work() sees that none of the
polled events are ready and the request isn't cancelled, it re-adds the
request to the waitqueue. (This can easily happen when polling a file
that doesn't pass an event mask when waking up its waitqueue.)
This is fundamentally broken for two reasons:
1. If a wakeup occurs between vfs_poll() and the request being
re-added to the waitqueue, it will be missed because the request
wasn't on the waitqueue at the time. Therefore, IOCB_CMD_POLL
might never complete even if the polled file is ready.
2. When the request isn't on the waitqueue, there is no way to be
notified that the waitqueue is being freed (which happens when its
lifetime is shorter than the struct file's). This is supposed to
happen via the waitqueue entries being woken up with POLLFREE.
Therefore, leave the requests on the waitqueue until they are actually
completed (or cancelled). To keep track of when aio_poll_complete_work
needs to be scheduled, use new fields in struct poll_iocb. Remove the
'done' field which is now redundant.
Note that this is consistent with how sys_poll() and eventpoll work;
their wakeup functions do *not* remove the waitqueue entries.
Fixes: 2c14fa838c ("aio: implement IOCB_CMD_POLL")
Cc: <stable@vger.kernel.org> # v4.18+
Link: https://lore.kernel.org/r/20211209010455.42744-5-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42288cb44c upstream.
Several ->poll() implementations are special in that they use a
waitqueue whose lifetime is the current task, rather than the struct
file as is normally the case. This is okay for blocking polls, since a
blocking poll occurs within one task; however, non-blocking polls
require another solution. This solution is for the queue to be cleared
before it is freed, using 'wake_up_poll(wq, EPOLLHUP | POLLFREE);'.
However, that has a bug: wake_up_poll() calls __wake_up() with
nr_exclusive=1. Therefore, if there are multiple "exclusive" waiters,
and the wakeup function for the first one returns a positive value, only
that one will be called. That's *not* what's needed for POLLFREE;
POLLFREE is special in that it really needs to wake up everyone.
Considering the three non-blocking poll systems:
- io_uring poll doesn't handle POLLFREE at all, so it is broken anyway.
- aio poll is unaffected, since it doesn't support exclusive waits.
However, that's fragile, as someone could add this feature later.
- epoll doesn't appear to be broken by this, since its wakeup function
returns 0 when it sees POLLFREE. But this is fragile.
Although there is a workaround (see epoll), it's better to define a
function which always sends POLLFREE to all waiters. Add such a
function. Also make it verify that the queue really becomes empty after
all waiters have been woken up.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211209010455.42744-2-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a66307d473 upstream.
The ASMedia 1092 has a configuration mode which will present a
dummy device; sadly the implementation falsely claims to provide
a device with 100M which doesn't actually exist.
So disable this device to avoid errors during boot.
Cc: stable@vger.kernel.org
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f58ac1adc7 upstream.
With the design of this driver, this condition is often triggered.
However, the counter that this interrupt indicates an overflow is never
read either, so overflowing is harmless.
On my system, when a CAN bus starts flapping up and down, this locks up
the whole system with lots of interrupts and printks.
Specifically, this interrupt indicates the CEL field of ECR has
overflowed. All reads of ECR mask out CEL.
Fixes: e0d1f4816f ("can: m_can: add Bosch M_CAN controller support")
Link: https://lore.kernel.org/all/20211129222628.7490-1-brian.silverman@bluerivertech.com
Cc: stable@vger.kernel.org
Signed-off-by: Brian Silverman <brian.silverman@bluerivertech.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b19926d4f3 upstream.
dma_fence_chain_find_seqno only ever returns the top fence in the
chain or an unsignalled fence. Hence if we request a seqno that
is already signalled it returns a NULL fence. Some callers are
not prepared to handle this, like the syncobj transfer functions
for example.
This behavior is "new" with timeline syncobj and it looks like
not all callers were updated. To fix this behavior make sure
that a successful drm_sync_find_fence always returns a non-NULL
fence.
v2: Move the fix to drm_syncobj_find_fence from the transfer
functions.
Fixes: ea569910cb ("drm/syncobj: add transition iotcls between binary and timeline v2")
Cc: stable@vger.kernel.org
Signed-off-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Reviewed-by: Christian König <christian.koenig@amd.com>
Acked-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211208023935.17018-1-bas@basnieuwenhuizen.nl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 548ec0805c upstream.
A delegation break could arrive as soon as we've called vfs_setlease. A
delegation break runs a callback which immediately (in
nfsd4_cb_recall_prepare) adds the delegation to del_recall_lru. If we
then exit nfs4_set_delegation without hashing the delegation, it will be
freed as soon as the callback is done with it, without ever being
removed from del_recall_lru.
Symptoms show up later as use-after-free or list corruption warnings,
usually in the laundromat thread.
I suspect aba2072f45 "nfsd: grant read delegations to clients holding
writes" made this bug easier to hit, but I looked as far back as v3.0
and it looks to me it already had the same problem. So I'm not sure
where the bug was introduced; it may have been there from the beginning.
Cc: stable@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 55df1ce0d4 upstream.
The superblock of version 1.0 doesn't get moved to the new position on a
device size change. This leads to a rdev without a superblock on a known
position, the raid can't be re-assembled.
The line was removed by mistake and is re-added by this patch.
Fixes: d9c0fa509e ("md: fix max sectors calculation for super 1.0")
Cc: stable@vger.kernel.org
Signed-off-by: Markus Hochholdinger <markus@hochholdinger.net>
Reviewed-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8289ed9f93 upstream.
I hit the BUG_ON() with generic/475 test case, and to my surprise, all
callers of btrfs_del_root_ref() are already aborting transaction, thus
there is not need for such BUG_ON(), just go to @out label and caller
will properly handle the error.
CC: stable@vger.kernel.org # 5.4+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2e3930529 upstream.
I got dmesg errors on generic/281 on our overnight fstests. Looking at
the history this happens occasionally, with errors like this
WARNING: CPU: 0 PID: 673217 at fs/btrfs/extent_io.c:6848 assert_eb_page_uptodate+0x3f/0x50
CPU: 0 PID: 673217 Comm: kworker/u4:13 Tainted: G W 5.16.0-rc2+ #469
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.13.0-2.fc32 04/01/2014
Workqueue: btrfs-cache btrfs_work_helper
RIP: 0010:assert_eb_page_uptodate+0x3f/0x50
RSP: 0018:ffffae598230bc60 EFLAGS: 00010246
RAX: 0017ffffc0002112 RBX: ffffebaec4100900 RCX: 0000000000001000
RDX: ffffebaec45733c7 RSI: ffffebaec4100900 RDI: ffff9fd98919f340
RBP: 0000000000000d56 R08: ffff9fd98e300000 R09: 0000000000000000
R10: 0001207370a91c50 R11: 0000000000000000 R12: 00000000000007b0
R13: ffff9fd98919f340 R14: 0000000001500000 R15: 0000000001cb0000
FS: 0000000000000000(0000) GS:ffff9fd9fbc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f549fcf8940 CR3: 0000000114908004 CR4: 0000000000370ef0
Call Trace:
extent_buffer_test_bit+0x3f/0x70
free_space_test_bit+0xa6/0xc0
load_free_space_tree+0x1d6/0x430
caching_thread+0x454/0x630
? rcu_read_lock_sched_held+0x12/0x60
? rcu_read_lock_sched_held+0x12/0x60
? rcu_read_lock_sched_held+0x12/0x60
? lock_release+0x1f0/0x2d0
btrfs_work_helper+0xf2/0x3e0
? lock_release+0x1f0/0x2d0
? finish_task_switch.isra.0+0xf9/0x3a0
process_one_work+0x270/0x5a0
worker_thread+0x55/0x3c0
? process_one_work+0x5a0/0x5a0
kthread+0x174/0x1a0
? set_kthread_struct+0x40/0x40
ret_from_fork+0x1f/0x30
This happens because we're trying to read from a extent buffer page that
is !PageUptodate. This happens because we will clear the page uptodate
when we have an IO error, but we don't clear the extent buffer uptodate.
If we do a read later and find this extent buffer we'll think its valid
and not return an error, and then trip over this warning.
Fix this by also clearing uptodate on the extent buffer when this
happens, so that we get an error when we do a btrfs_search_slot() and
find this block later.
CC: stable@vger.kernel.org # 5.4+
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 619764cc2e upstream.
This fixes the SND_PCI_QUIRK(...) of the TongFang PHxTxX1 barebone. This
fixes the issue of sound not working after s3 suspend.
When waking up from s3 suspend the Coef 0x10 is set to 0x0220 instead of
0x0020. Setting the value manually makes the sound work again. This patch
does this automatically.
While being on it, I also fixed the comment formatting of the quirk and
shortened variable and function names.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Fixes: dd6dd6e3c7 ("ALSA: hda/realtek: Add quirk for TongFang PHxTxX1")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211202165010.876431-1-wse@tuxedocomputers.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6409dd6bd upstream.
When control_compat.c:copy_ctl_value_to_user() is used, by
ctl_elem_read_user() & ctl_elem_write_user(), it must also copy back the
snd_ctl_elem_id value that may have been updated (filled in) by the call
to snd_ctl_elem_read/snd_ctl_elem_write().
This matches the functionality provided by snd_ctl_elem_read_user() and
snd_ctl_elem_write_user(), via snd_ctl_build_ioff().
Without this, and without making additional calls to snd_ctl_info()
which are unnecessary when using the non-compat calls, a userspace
application will not know the numid value for the element and
consequently will not be able to use the poll/read interface on the
control file to determine which elements have updates.
Signed-off-by: Alan Young <consult.awy@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211202150607.543389-1-consult.awy@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ebfaa11eb upstream.
Prior to commit 0baedd7927 ("KVM: x86: make Hyper-V PV TLB flush use
tlb_flush_guest()"), kvm_hv_flush_tlb() was using 'KVM_REQ_TLB_FLUSH |
KVM_REQUEST_NO_WAKEUP' when making a request to flush TLBs on other vCPUs
and KVM_REQ_TLB_FLUSH is/was defined as:
(0 | KVM_REQUEST_WAIT | KVM_REQUEST_NO_WAKEUP)
so KVM_REQUEST_WAIT was lost. Hyper-V TLFS, however, requires that
"This call guarantees that by the time control returns back to the
caller, the observable effects of all flushes on the specified virtual
processors have occurred." and without KVM_REQUEST_WAIT there's a small
chance that the vCPU making the TLB flush will resume running before
all IPIs get delivered to other vCPUs and a stale mapping can get read
there.
Fix the issue by adding KVM_REQUEST_WAIT flag to KVM_REQ_TLB_FLUSH_GUEST:
kvm_hv_flush_tlb() is the sole caller which uses it for
kvm_make_all_cpus_request()/kvm_make_vcpus_request_mask() where
KVM_REQUEST_WAIT makes a difference.
Cc: stable@kernel.org
Fixes: 0baedd7927 ("KVM: x86: make Hyper-V PV TLB flush use tlb_flush_guest()")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20211209102937.584397-1-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a1aa356dd upstream.
iavf_set_ringparams doesn't communicate to the user that
1. The user requested descriptor count is out of range. Instead it
just quietly sets descriptors to the "clamped" value and calls it
done. This makes it look an invalid value was successfully set as
the descriptor count when this isn't actually true.
2. The user provided descriptor count needs to be inflated for alignment
reasons.
This behavior is confusing. The ice driver has already addressed this
by rejecting invalid values for descriptor count and
messaging for alignment adjustments.
Do the same thing here by adding the error and info messages.
Fixes: fbb7ddfef2 ("i40evf: core ethtool functionality")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Michal Maloszewski <michal.maloszewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e4dcc1396 upstream.
If the PF experiences an FLR, the VF's MSI and MSI-X configuration will
be conveniently and silently removed in the process. When this happens,
reset recovery will appear to complete normally but no traffic will
pass. The netdev watchdog will helpfully notify everyone of this issue.
To prevent such public embarrassment, restore MSI configuration at every
reset. For normal resets, this will do no harm, but for VF resets
resulting from a PF FLR, this will keep the VF working.
Fixes: 5eae00c57f ("i40evf: main driver core")
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae68d93354 upstream.
When an IPv4 packet is received, the ip_rcv_core(...) sets the receiving
interface index into the IPv4 socket control block (v5.16-rc4,
net/ipv4/ip_input.c line 510):
IPCB(skb)->iif = skb->skb_iif;
If that IPv4 packet is meant to be encapsulated in an outer IPv6+SRH
header, the seg6_do_srh_encap(...) performs the required encapsulation.
In this case, the seg6_do_srh_encap function clears the IPv6 socket control
block (v5.16-rc4 net/ipv6/seg6_iptunnel.c line 163):
memset(IP6CB(skb), 0, sizeof(*IP6CB(skb)));
The memset(...) was introduced in commit ef489749aa ("ipv6: sr: clear
IP6CB(skb) on SRH ip4ip6 encapsulation") a long time ago (2019-01-29).
Since the IPv6 socket control block and the IPv4 socket control block share
the same memory area (skb->cb), the receiving interface index info is lost
(IP6CB(skb)->iif is set to zero).
As a side effect, that condition triggers a NULL pointer dereference if
commit 0857d6f8c7 ("ipv6: When forwarding count rx stats on the orig
netdev") is applied.
To fix that issue, we set the IP6CB(skb)->iif with the index of the
receiving interface once again.
Fixes: ef489749aa ("ipv6: sr: clear IP6CB(skb) on SRH ip4ip6 encapsulation")
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20211208195409.12169-1-andrea.mayer@uniroma2.it
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c56c96303e upstream.
In line 800 (#1), nfp_cpp_area_alloc() allocates and initializes a
CPP area structure. But in line 807 (#2), when the cache is allocated
failed, this CPP area structure is not freed, which will result in
memory leak.
We can fix it by freeing the CPP area when the cache is allocated
failed (#2).
792 int nfp_cpp_area_cache_add(struct nfp_cpp *cpp, size_t size)
793 {
794 struct nfp_cpp_area_cache *cache;
795 struct nfp_cpp_area *area;
800 area = nfp_cpp_area_alloc(cpp, NFP_CPP_ID(7, NFP_CPP_ACTION_RW, 0),
801 0, size);
// #1: allocates and initializes
802 if (!area)
803 return -ENOMEM;
805 cache = kzalloc(sizeof(*cache), GFP_KERNEL);
806 if (!cache)
807 return -ENOMEM; // #2: missing free
817 return 0;
818 }
Fixes: 4cb584e0ee ("nfp: add CPP access core")
Signed-off-by: Jianglei Nie <niejianglei2021@163.com>
Acked-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20211209061511.122535-1-niejianglei2021@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28dc1b86f8 upstream.
If the hardware is constantly receiving unicast or broadcast packets
during driver load, the device previously counted many GLV_RDPC (VSI
dropped packets) events during init. This causes confusing dropped
packet statistics during driver load. The dropped packets counter
incrementing does stop once the driver finishes loading.
Avoid this problem by baselining our statistics at the end of driver
open instead of the end of probe.
Fixes: cdedef59de ("ice: Configure VSIs for Tx/Rx")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2fa7d94afc upstream.
The first commit cited below attempts to fix the off-by-one error that
appeared in some comparisons with an open range. Due to this error,
arithmetically equivalent pieces of code could get different verdicts
from the verifier, for example (pseudocode):
// 1. Passes the verifier:
if (data + 8 > data_end)
return early
read *(u64 *)data, i.e. [data; data+7]
// 2. Rejected by the verifier (should still pass):
if (data + 7 >= data_end)
return early
read *(u64 *)data, i.e. [data; data+7]
The attempted fix, however, shifts the range by one in a wrong
direction, so the bug not only remains, but also such piece of code
starts failing in the verifier:
// 3. Rejected by the verifier, but the check is stricter than in #1.
if (data + 8 >= data_end)
return early
read *(u64 *)data, i.e. [data; data+7]
The change performed by that fix converted an off-by-one bug into
off-by-two. The second commit cited below added the BPF selftests
written to ensure than code chunks like #3 are rejected, however,
they should be accepted.
This commit fixes the off-by-two error by adjusting new_range in the
right direction and fixes the tests by changing the range into the
one that should actually fail.
Fixes: fb2a311a31 ("bpf: fix off by one for range markings with L{T, E} patterns")
Fixes: b37242c773 ("bpf: add test cases to bpf selftests to cover all access tests")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20211130181607.593149-1-maximmi@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f45b2974cc upstream.
The arch_prepare_bpf_dispatcher function does not have a prototype, and
yields the following warning when W=1 is enabled for the kernel build.
>> arch/x86/net/bpf_jit_comp.c:2188:5: warning: no previous \
prototype for 'arch_prepare_bpf_dispatcher' [-Wmissing-prototypes]
2188 | int arch_prepare_bpf_dispatcher(void *image, s64 *funcs, \
int num_funcs)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~
Remove the warning by adding a function declaration to include/linux/bpf.h.
Fixes: 75ccbef636 ("bpf: Introduce BPF dispatcher")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Björn Töpel <bjorn@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20211117125708.769168-1-bjorn@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d43b75fbc2 upstream.
After the below patch, the conntrack attached to skb is set to "notrack" in
the context of vrf device, for locally generated packets.
But this is true only when the default qdisc is set to the vrf device. When
changing the qdisc, notrack is not set anymore.
In fact, there is a shortcut in the vrf driver, when the default qdisc is
set, see commit dcdd43c41e ("net: vrf: performance improvements for
IPv4") for more details.
This patch ensures that the behavior is always the same, whatever the qdisc
is.
To demonstrate the difference, a new test is added in conntrack_vrf.sh.
Fixes: 8c9c296adf ("vrf: run conntrack only in context of lower/physdev for locally generated packets")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Florian Westphal <fw@strlen.de>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ff2fc0286 upstream.
Reserving memory using efi_mem_reserve() calls into the x86
efi_arch_mem_reserve() function. This function will insert a new EFI
memory descriptor into the EFI memory map representing the area of
memory to be reserved and marking it as EFI runtime memory. As part
of adding this new entry, a new EFI memory map is allocated and mapped.
The mapping is where a problem can occur. This new memory map is mapped
using early_memremap() and generally mapped encrypted, unless the new
memory for the mapping happens to come from an area of memory that is
marked as EFI_BOOT_SERVICES_DATA memory. In this case, the new memory will
be mapped unencrypted. However, during replacement of the old memory map,
efi_mem_type() is disabled, so the new memory map will now be long-term
mapped encrypted (in efi.memmap), resulting in the map containing invalid
data and causing the kernel boot to crash.
Since it is known that the area will be mapped encrypted going forward,
explicitly map the new memory map as encrypted using early_memremap_prot().
Cc: <stable@vger.kernel.org> # 4.14.x
Fixes: 8f716c9b5f ("x86/mm: Add support to access boot related data in the clear")
Link: https://lore.kernel.org/all/ebf1eb2940405438a09d51d121ec0d02c8755558.1634752931.git.thomas.lendacky@amd.com/
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
[ardb: incorporate Kconfig fix by Arnd]
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb12797ab1 upstream.
The CAN clock frequency is used when calculating the CAN bittiming
parameters. When wrong clock frequency is used, the device may end up
with wrong bittiming parameters, depending on user requested bittiming
parameters.
To avoid this, get the CAN clock frequency from the device. Various
existing Kvaser Leaf products use different CAN clocks.
Fixes: 080f40a6fa ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Link: https://lore.kernel.org/all/20211208152122.250852-2-extja@kvaser.com
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60a8b5a161 upstream.
This buffer is currently allocated in hfi1_init():
if (reinit)
ret = init_after_reset(dd);
else
ret = loadtime_init(dd);
if (ret)
goto done;
/* allocate dummy tail memory for all receive contexts */
dd->rcvhdrtail_dummy_kvaddr = dma_alloc_coherent(&dd->pcidev->dev,
sizeof(u64),
&dd->rcvhdrtail_dummy_dma,
GFP_KERNEL);
if (!dd->rcvhdrtail_dummy_kvaddr) {
dd_dev_err(dd, "cannot allocate dummy tail memory\n");
ret = -ENOMEM;
goto done;
}
The reinit triggered path will overwrite the old allocation and leak it.
Fix by moving the allocation to hfi1_alloc_devdata() and the deallocation
to hfi1_free_devdata().
Link: https://lore.kernel.org/r/20211129192008.101968.91302.stgit@awfm-01.cornelisnetworks.com
Cc: stable@vger.kernel.org
Fixes: 46b010d3ee ("staging/rdma/hfi1: Workaround to prevent corruption during packet delivery")
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7e945e228 upstream.
The sixth byte of packet data has to be looked up in the sixth group,
not in the seventh one, even if we load the bucket data into ymm6
(and not ymm5, for convenience of tracking stalls).
Without this fix, matching on a MAC address as first field of a set,
if 8-bit groups are selected (due to a small set size) would fail,
that is, the given MAC address would never match.
Reported-by: Nikita Yushchenko <nikita.yushchenko@virtuozzo.com>
Cc: <stable@vger.kernel.org> # 5.6.x
Fixes: 7400b06396 ("nft_set_pipapo: Introduce AVX2-based lookup implementation")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Tested-By: Nikita Yushchenko <nikita.yushchenko@virtuozzo.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9003fbe0f3 upstream.
Add a HID_QUIRK_NO_INIT_REPORTS quirk for the
Microsoft Surface 3 (non pro) type-cover.
Trying to init the reports seems to confuse the type-cover and
causes 2 issues:
1. Despite hid-multitouch sending the command to switch the
touchpad to multitouch mode, it keeps sending events on the
mouse emulation interface.
2. The touchpad completely stops sending events after a reboot.
Adding the HID_QUIRK_NO_INIT_REPORTS quirk fixes both issues.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67a5a68013 upstream.
Fedora Rawhide has started including gcc 11,and the g++ compiler
throws a wobbly when it hits scripts/gcc-plugins:
HOSTCXX scripts/gcc-plugins/latent_entropy_plugin.so
In file included from /usr/include/c++/11/type_traits:35,
from /usr/lib/gcc/x86_64-redhat-linux/11/plugin/include/system.h:244,
from /usr/lib/gcc/x86_64-redhat-linux/11/plugin/include/gcc-plugin.h:28,
from scripts/gcc-plugins/gcc-common.h:7,
from scripts/gcc-plugins/latent_entropy_plugin.c:78:
/usr/include/c++/11/bits/c++0x_warning.h:32:2: error: #error This file requires compiler and library support for the ISO
C++ 2011 standard. This support must be enabled with the -std=c++11 or -std=gnu++11 compiler options.
32 | #error This file requires compiler and library support \
In fact, it works just fine with c++11, which has been in gcc since 4.8,
and we now require 4.9 as a minimum.
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/82487.1609006918@turing-police
Cc: Thomas Lindroth <thomas.lindroth@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e860048c5 upstream.
Linus pointed out a third of the time in the Kconfig parse stage comes
from the single invocation of cc1plus in scripts/gcc-plugin.sh [1],
and directly testing plugin-version.h for existence cuts down the
overhead a lot. [2]
This commit takes one step further to kill the build test entirely.
The small piece of code was probably intended to test the C++ designated
initializer, which was not supported until C++20.
In fact, with -pedantic option given, both GCC and Clang emit a warning.
$ echo 'class test { public: int test; } test = { .test = 1 };' | g++ -x c++ -pedantic - -fsyntax-only
<stdin>:1:43: warning: C++ designated initializers only available with '-std=c++2a' or '-std=gnu++2a' [-Wpedantic]
$ echo 'class test { public: int test; } test = { .test = 1 };' | clang++ -x c++ -pedantic - -fsyntax-only
<stdin>:1:43: warning: designated initializers are a C++20 extension [-Wc++20-designator]
class test { public: int test; } test = { .test = 1 };
^
1 warning generated.
Otherwise, modern C++ compilers should be able to build the code, and
hopefully skipping this test should not make any practical problem.
Checking the existence of plugin-version.h is still needed to ensure
the plugin-dev package is installed. The test code is now small enough
to be embedded in scripts/gcc-plugins/Kconfig.
[1] https://lore.kernel.org/lkml/CAHk-=wjU4DCuwQ4pXshRbwDCUQB31ScaeuDo1tjoZ0_PjhLHzQ@mail.gmail.com/
[2] https://lore.kernel.org/lkml/CAHk-=whK0aQxs6Q5ijJmYF1n2ch8cVFSUzU5yUM_HOjig=+vnw@mail.gmail.com/
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20201203125700.161354-1-masahiroy@kernel.org
Cc: Thomas Lindroth <thomas.lindroth@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72ee48ee89 upstream.
Currently, the UVC function is activated when open on the corresponding
v4l2 device is called. On another open the activation of the function
fails since the deactivation counter in `usb_function_activate` equals
0. However the error is not returned to userspace since the open of the
v4l2 device is successful.
On a close the function is deactivated (since deactivation counter still
equals 0) and the video is disabled in `uvc_v4l2_release`, although the
UVC application potentially is streaming.
Move activation of UVC function to subscription on UVC_EVENT_SETUP
because there we can guarantee for a userspace application utilizing
UVC. Block subscription on UVC_EVENT_SETUP while another application
already is subscribed to it, indicated by `bool func_connected` in
`struct uvc_device`. Extend the `struct uvc_file_handle` with member
`bool is_uvc_app_handle` to tag it as the handle used by the userspace
UVC application.
With this a process is able to check capabilities of the v4l2 device
without deactivating the function for the actual UVC application.
Reviewed-By: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Thomas Haemmerle <thomas.haemmerle@wolfvision.net>
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Acked-by: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/20211003201355.24081-1-m.grzeschik@pengutronix.de
Cc: Dan Vacura <W36195@motorola.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5961060692 upstream.
When the TLS cipher suite uses CCM mode, including AES CCM and
SM4 CCM, the first byte of the B0 block is flags, and the real
IV starts from the second byte. The XOR operation of the IV and
rec_seq should be skip this byte, that is, add the iv_offset.
Fixes: f295b3ae9f ("net/tls: Add support of AES128-CCM based ciphers")
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Cc: Vakul Garg <vakul.garg@nxp.com>
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit afdb4a5b1d upstream.
In commit c8c3735997 ("parisc: Enhance detection of synchronous cr16
clocksources") I assumed that CPUs on the same physical core are syncronous.
While booting up the kernel on two different C8000 machines, one with a
dual-core PA8800 and one with a dual-core PA8900 CPU, this turned out to be
wrong. The symptom was that I saw a jump in the internal clocks printed to the
syslog and strange overall behaviour. On machines which have 4 cores (2
dual-cores) the problem isn't visible, because the current logic already marked
the cr16 clocksource unstable in this case.
This patch now marks the cr16 interval timers unstable if we have more than one
CPU in the system, and it fixes this issue.
Fixes: c8c3735997 ("parisc: Enhance detection of synchronous cr16 clocksources")
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org> # v5.15+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f85e04503f upstream.
Commit f45709df77 ("serial: 8250: Don't touch RTS modem control while
in rs485 mode") sought to prevent user space from interfering with rs485
communication by ignoring a TIOCMSET ioctl() which changes RTS polarity.
It did so in serial8250_do_set_mctrl(), which turns out to be too deep
in the call stack: When a uart_port is opened, RTS polarity is set by
the rs485-aware function uart_port_dtr_rts(). It calls down to
serial8250_do_set_mctrl() and that particular RTS polarity change should
*not* be ignored.
The user-visible result is that on 8250_omap ports which use rs485 with
inverse polarity (RTS bit in MCR register is 1 to receive, 0 to send),
a newly opened port initially sets up RTS for sending instead of
receiving. That's because omap_8250_startup() sets the cached value
up->mcr to 0 and omap_8250_restore_regs() subsequently writes it to the
MCR register. Due to the commit, serial8250_do_set_mctrl() preserves
that incorrect register value:
do_sys_openat2
do_filp_open
path_openat
vfs_open
do_dentry_open
chrdev_open
tty_open
uart_open
tty_port_open
uart_port_activate
uart_startup
uart_port_startup
serial8250_startup
omap_8250_startup # up->mcr = 0
uart_change_speed
serial8250_set_termios
omap_8250_set_termios
omap_8250_restore_regs
serial8250_out_MCR # up->mcr written
tty_port_block_til_ready
uart_dtr_rts
uart_port_dtr_rts
serial8250_set_mctrl
omap8250_set_mctrl
serial8250_do_set_mctrl # mcr[1] = 1 ignored
Fix by intercepting RTS changes from user space in uart_tiocmset()
instead.
Link: https://lore.kernel.org/linux-serial/20211027111644.1996921-1-baocheng.su@siemens.com/
Fixes: f45709df77 ("serial: 8250: Don't touch RTS modem control while in rs485 mode")
Cc: Chao Zeng <chao.zeng@siemens.com>
Cc: stable@vger.kernel.org # v5.7+
Reported-by: Su Bao Cheng <baocheng.su@siemens.com>
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Tested-by: Su Bao Cheng <baocheng.su@siemens.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/21170e622a1aaf842a50b32146008b5374b3dd1d.1637596432.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 00de977f9e upstream.
Commit 761ed4a945 ("tty: serial_core: convert uart_close to use
tty_port_close") converted serial core to use tty_port_close() but
failed to notice that the transmit buffer still needs to be freed on
final close.
Not freeing the transmit buffer means that the buffer is no longer
cleared on next open so that any ioctl() waiting for the buffer to drain
might wait indefinitely (e.g. on termios changes) or that stale data can
end up being transmitted in case tx is restarted.
Furthermore, the buffer of any port that has been opened would leak on
driver unbind.
Note that the port lock is held when clearing the buffer pointer due to
the ldisc race worked around by commit a5ba1d95e4 ("uart: fix race
between uart_put_char() and uart_shutdown()").
Also note that the tty-port shutdown() callback is not called for
console ports so it is not strictly necessary to free the buffer page
after releasing the lock (cf. d72402145a ("tty/serial: do not free
trasnmit buffer page under port lock")).
Link: https://lore.kernel.org/r/319321886d97c456203d5c6a576a5480d07c3478.1635781688.git.baruch@tkos.co.il
Fixes: 761ed4a945 ("tty: serial_core: convert uart_close to use tty_port_close")
Cc: stable@vger.kernel.org # 4.9
Cc: Rob Herring <robh@kernel.org>
Reported-by: Baruch Siach <baruch@tkos.co.il>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211108085431.12637-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b40de7469e upstream.
The current implementation uses 0 as lower limit for the baud rate
tolerance for tegra20 and tegra30 chips which causes isses on UART
initialization as soon as baud rate clock is lower than required even
when within the standard UART tolerance of +/- 4%.
This fix aligns the implementation with the initial commit description
of +/- 4% tolerance for tegra chips other than tegra186 and
tegra194.
Fixes: d781ec21ba ("serial: tegra: report clk rate errors")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Patrik John <patrik.john@u-blox.com>
Link: https://lore.kernel.org/r/sig.19614244f8.20211123132737.88341-1-patrik.john@u-blox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac442a077a upstream.
The document 'ACPI for Arm Components 1.0' defines the following
_HID mappings:
-'Prime cell UART (PL011)': ARMH0011
-'SBSA UART': ARMHB000
Use the sbsa-uart driver when a device is described with
the 'ARMHB000' _HID.
Note:
PL011 devices currently use the sbsa-uart driver instead of the
uart-pl011 driver. Indeed, PL011 devices are not bound to a clock
in ACPI. It is not possible to change their baudrate.
Cc: <stable@vger.kernel.org>
Signed-off-by: Pierre Gondois <Pierre.Gondois@arm.com>
Link: https://lore.kernel.org/r/20211109172248.19061-1-Pierre.Gondois@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7492ffc90f upstream.
The CONSOLE_POLLING mode is used for tools like k(g)db. In this kind of
setup, it is often sharing a serial device with the normal system console.
This is usually no problem because the polling helpers can consume input
values directly (when in kgdb context) and the normal Linux handlers can
only consume new input values after kgdb switched back.
This is not true anymore when RX DMA is enabled for UARTDM controllers.
Single input values can no longer be received correctly. Instead following
seems to happen:
* on 1. input, some old input is read (continuously)
* on 2. input, two old inputs are read (continuously)
* on 3. input, three old input values are read (continuously)
* on 4. input, 4 previous inputs are received
This repeats then for each group of 4 input values.
This behavior changes slightly depending on what state the controller was
when the first input was received. But this makes working with kgdb
basically impossible because control messages are always corrupted when
kgdboc tries to parse them.
RX DMA should therefore be off when CONSOLE_POLLING is enabled to avoid
these kind of problems. No such problem was noticed for TX DMA.
Fixes: 9969394501 ("tty: serial: msm: Add RX DMA support")
Cc: stable@vger.kernel.org
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Link: https://lore.kernel.org/r/20211113121050.7266-1-sven@narfation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51523ed1c2 upstream.
The trampoline_pgd only maps the 0xfffffff000000000-0xffffffffffffffff
range of kernel memory (with 4-level paging). This range contains the
kernel's text+data+bss mappings and the module mapping space but not the
direct mapping and the vmalloc area.
This is enough to get the application processors out of real-mode, but
for code that switches back to real-mode the trampoline_pgd is missing
important parts of the address space. For example, consider this code
from arch/x86/kernel/reboot.c, function machine_real_restart() for a
64-bit kernel:
#ifdef CONFIG_X86_32
load_cr3(initial_page_table);
#else
write_cr3(real_mode_header->trampoline_pgd);
/* Exiting long mode will fail if CR4.PCIDE is set. */
if (boot_cpu_has(X86_FEATURE_PCID))
cr4_clear_bits(X86_CR4_PCIDE);
#endif
/* Jump to the identity-mapped low memory code */
#ifdef CONFIG_X86_32
asm volatile("jmpl *%0" : :
"rm" (real_mode_header->machine_real_restart_asm),
"a" (type));
#else
asm volatile("ljmpl *%0" : :
"m" (real_mode_header->machine_real_restart_asm),
"D" (type));
#endif
The code switches to the trampoline_pgd, which unmaps the direct mapping
and also the kernel stack. The call to cr4_clear_bits() will find no
stack and crash the machine. The real_mode_header pointer below points
into the direct mapping, and dereferencing it also causes a crash.
The reason this does not crash always is only that kernel mappings are
global and the CR3 switch does not flush those mappings. But if theses
mappings are not in the TLB already, the above code will crash before it
can jump to the real-mode stub.
Extend the trampoline_pgd to contain all kernel mappings to prevent
these crashes and to make code which runs on this page-table more
robust.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20211202153226.22946-5-joro@8bytes.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b50db7095f upstream.
There are cases that the TSC clocksource is wrongly judged as unstable by
the clocksource watchdog mechanism which tries to validate the TSC against
HPET, PM_TIMER or jiffies. While there is hardly a general reliable way to
check the validity of a watchdog, Thomas Gleixner proposed [1]:
"I'm inclined to lift that requirement when the CPU has:
1) X86_FEATURE_CONSTANT_TSC
2) X86_FEATURE_NONSTOP_TSC
3) X86_FEATURE_NONSTOP_TSC_S3
4) X86_FEATURE_TSC_ADJUST
5) At max. 4 sockets
After two decades of horrors we're finally at a point where TSC seems
to be halfway reliable and less abused by BIOS tinkerers. TSC_ADJUST
was really key as we can now detect even small modifications reliably
and the important point is that we can cure them as well (not pretty
but better than all other options)."
As feature #3 X86_FEATURE_NONSTOP_TSC_S3 only exists on several generations
of Atom processorz, and is always coupled with X86_FEATURE_CONSTANT_TSC
and X86_FEATURE_NONSTOP_TSC, skip checking it, and also be more defensive
to use maximal 2 sockets.
The check is done inside tsc_init() before registering 'tsc-early' and
'tsc' clocksources, as there were cases that both of them had been
wrongly judged as unreliable.
For more background of tsc/watchdog, there is a good summary in [2]
[tglx} Update vs. jiffies:
On systems where the only remaining clocksource aside of TSC is jiffies
there is no way to make this work because that creates a circular
dependency. Jiffies accuracy depends on not missing a periodic timer
interrupt, which is not guaranteed. That could be detected by TSC, but as
TSC is not trusted this cannot be compensated. The consequence is a
circulus vitiosus which results in shutting down TSC and falling back to
the jiffies clocksource which is even more unreliable.
[1]. https://lore.kernel.org/lkml/87eekfk8bd.fsf@nanos.tec.linutronix.de/
[2]. https://lore.kernel.org/lkml/87a6pimt1f.ffs@nanos.tec.linutronix.de/
[ tglx: Refine comment and amend changelog ]
Fixes: 6e3cd95234 ("x86/hpet: Use another crystalball to evaluate HPET usability")
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "Paul E. McKenney" <paulmck@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211117023751.24190-2-feng.tang@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09f736aa95 upstream.
Turns out some xHC controllers require all 64 bits in the CRCR register
to be written to execute a command abort.
The lower 32 bits containing the command abort bit is written first.
In case the command ring stops before we write the upper 32 bits then
hardware may use these upper bits to set the commnd ring dequeue pointer.
Solve this by making sure the upper 32 bits contain a valid command
ring dequeue pointer.
The original patch that only wrote the first 32 to stop the ring went
to stable, so this fix should go there as well.
Fixes: ff0e50d356 ("xhci: Fix command ring pointer corruption while aborting a command")
Cc: stable@vger.kernel.org
Tested-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211126122340.1193239-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3dfac26e2e upstream.
Fix a division by zero in `vgacon_resize' with a backtrace like:
vgacon_resize
vc_do_resize
vgacon_init
do_bind_con_driver
do_unbind_con_driver
fbcon_fb_unbind
do_unregister_framebuffer
do_register_framebuffer
register_framebuffer
__drm_fb_helper_initial_config_and_unlock
drm_helper_hpd_irq_event
dw_hdmi_irq
irq_thread
kthread
caused by `c->vc_cell_height' not having been initialized. This has
only started to trigger with commit 860dafa902 ("vt: Fix character
height handling with VT_RESIZEX"), however the ultimate offender is
commit 50ec42edd9 ("[PATCH] Detaching fbcon: fix vgacon to allow
retaking of the console").
Said commit has added a call to `vc_resize' whenever `vgacon_init' is
called with the `init' argument set to 0, which did not happen before.
And the call is made before a key vgacon boot parameter retrieved in
`vgacon_startup' has been propagated in `vgacon_init' for `vc_resize' to
use to the console structure being worked on. Previously the parameter
was `c->vc_font.height' and now it is `c->vc_cell_height'.
In this particular scenario the registration of fbcon has failed and vt
resorts to vgacon. Now fbcon does have initialized `c->vc_font.height'
somehow, unlike `c->vc_cell_height', which is why this code did not
crash before, but either way the boot parameters should have been copied
to the console structure ahead of the call to `vc_resize' rather than
afterwards, so that first the call has a chance to use them and second
they do not change the console structure to something possibly different
from what was used by `vc_resize'.
Move the propagation of the vgacon boot parameters ahead of the call to
`vc_resize' then. Adjust the comment accordingly.
Fixes: 50ec42edd9 ("[PATCH] Detaching fbcon: fix vgacon to allow retaking of the console")
Cc: stable@vger.kernel.org # v2.6.18+
Reported-by: Wim Osterholt <wim@djo.tudelft.nl>
Reported-by: Pavel V. Panteleev <panteleev_p@mcst.ru>
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2110252317110.58149@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f9fee4cde upstream.
On newer debian releases the debian-provided "installkernel" script is
installed in /usr/sbin. Fix the kernel install.sh script to look for the
script in this directory as well.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org> # v3.13+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d7c29b777 upstream.
Default KBUILD_IMAGE to $(boot)/bzImage if a self-extracting
(CONFIG_PARISC_SELF_EXTRACT=y) kernel is to be built.
This fixes the bindeb-pkg make target.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c07e45553d ]
Commit
18ec54fdd6 ("x86/speculation: Prepare entry code for Spectre v1 swapgs mitigations")
added FENCE_SWAPGS_{KERNEL|USER}_ENTRY for conditional SWAPGS. In
paranoid_entry(), it uses only FENCE_SWAPGS_KERNEL_ENTRY for both
branches. This is because the fence is required for both cases since the
CR3 write is conditional even when PTI is enabled.
But
96b2371413 ("x86/entry/64: Switch CR3 before SWAPGS in paranoid entry")
changed the order of SWAPGS and the CR3 write. And it missed the needed
FENCE_SWAPGS_KERNEL_ENTRY for the user gsbase case.
Add it back by changing the branches so that FENCE_SWAPGS_KERNEL_ENTRY
can cover both branches.
[ bp: Massage, fix typos, remove obsolete comment while at it. ]
Fixes: 96b2371413 ("x86/entry/64: Switch CR3 before SWAPGS in paranoid entry")
Signed-off-by: Lai Jiangshan <laijs@linux.alibaba.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20211126101209.8613-2-jiangshanlai@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 53c9d92409 ]
SWAPGS is used only for interrupts coming from user mode or for
returning to user mode. So there is no reason to use the PARAVIRT
framework, as it can easily be replaced by an ALTERNATIVE depending
on X86_FEATURE_XENPV.
There are several instances using the PV-aware SWAPGS macro in paths
which are never executed in a Xen PV guest. Replace those with the
plain swapgs instruction. For SWAPGS_UNSAFE_STACK the same applies.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20210120135555.32594-5-jgross@suse.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 315c4f8848 ]
Commit d81ae8aac8 ("sched/uclamp: Fix initialization of struct
uclamp_rq") introduced a bug where uclamp_max of the rq is not reset to
match the woken up task's uclamp_max when the rq is idle.
The code was relying on rq->uclamp_max initialized to zero, so on first
enqueue
static inline void uclamp_rq_inc_id(struct rq *rq, struct task_struct *p,
enum uclamp_id clamp_id)
{
...
if (uc_se->value > READ_ONCE(uc_rq->value))
WRITE_ONCE(uc_rq->value, uc_se->value);
}
was actually resetting it. But since commit d81ae8aac8 changed the
default to 1024, this no longer works. And since rq->uclamp_flags is
also initialized to 0, neither above code path nor uclamp_idle_reset()
update the rq->uclamp_max on first wake up from idle.
This is only visible from first wake up(s) until the first dequeue to
idle after enabling the static key. And it only matters if the
uclamp_max of this task is < 1024 since only then its uclamp_max will be
effectively ignored.
Fix it by properly initializing rq->uclamp_flags = UCLAMP_FLAG_IDLE to
ensure uclamp_idle_reset() is called which then will update the rq
uclamp_max value as expected.
Fixes: d81ae8aac8 ("sched/uclamp: Fix initialization of struct uclamp_rq")
Signed-off-by: Qais Yousef <qais.yousef@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Valentin Schneider <Valentin.Schneider@arm.com>
Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Link: https://lkml.kernel.org/r/20211202112033.1705279-1-qais.yousef@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c8f6a2e31 ]
In the native case, PER_CPU_VAR(cpu_tss_rw + TSS_sp0) is the
trampoline stack. But XEN pv doesn't use trampoline stack, so
PER_CPU_VAR(cpu_tss_rw + TSS_sp0) is also the kernel stack.
In that case, source and destination stacks are identical, which means
that reusing swapgs_restore_regs_and_return_to_usermode() in XEN pv
would cause %rsp to move up to the top of the kernel stack and leave the
IRET frame below %rsp.
This is dangerous as it can be corrupted if #NMI / #MC hit as either of
these events occurring in the middle of the stack pushing would clobber
data on the (original) stack.
And, with XEN pv, swapgs_restore_regs_and_return_to_usermode() pushing
the IRET frame on to the original address is useless and error-prone
when there is any future attempt to modify the code.
[ bp: Massage commit message. ]
Fixes: 7f2590a110 ("x86/entry/64: Use a per-CPU trampoline stack for IDT entries")
Signed-off-by: Lai Jiangshan <laijs@linux.alibaba.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lkml.kernel.org/r/20211126101209.8613-4-jiangshanlai@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1367afaa2e ]
The commit
c758907004 ("x86/entry/64: Remove unneeded kernel CR3 switching")
removed a CR3 write in the faulting path of load_gs_index().
But the path's FENCE_SWAPGS_USER_ENTRY has no fence operation if PTI is
enabled, see spectre_v1_select_mitigation().
Rather, it depended on the serializing CR3 write of SWITCH_TO_KERNEL_CR3
and since it got removed, add a FENCE_SWAPGS_KERNEL_ENTRY call to make
sure speculation is blocked.
[ bp: Massage commit message and comment. ]
Fixes: c758907004 ("x86/entry/64: Remove unneeded kernel CR3 switching")
Signed-off-by: Lai Jiangshan <laijs@linux.alibaba.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20211126101209.8613-3-jiangshanlai@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d5379d047 ]
Properly type the operands being passed to __put_user()/__get_user().
Otherwise, these routines truncate data for dependent instructions
(e.g., INSW) and only read/write one byte.
This has been tested by sending a string with REP OUTSW to a port and
then reading it back in with REP INSW on the same port.
Previous behavior was to only send and receive the first char of the
size. For example, word operations for "abcd" would only read/write
"ac". With change, the full string is now written and read back.
Fixes: f980f9c31a (x86/sev-es: Compile early handler code into kernel image)
Signed-off-by: Michael Sterritt <sterritt@google.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Marc Orr <marcorr@google.com>
Reviewed-by: Peter Gonda <pgonda@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Link: https://lkml.kernel.org/r/20211119232757.176201-1-sterritt@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfbb307c62 ]
The error paths in the prepare_vmcs02() function are supposed to set
*entry_failure_code but this path does not. It leads to using an
uninitialized variable in the caller.
Fixes: 71f7347025 ("KVM: nVMX: Load GUEST_IA32_PERF_GLOBAL_CTRL MSR on VM-Entry")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Message-Id: <20211130125337.GB24578@kili>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb1d220da0 ]
If we run the following perf command in an AMD Milan guest:
perf stat \
-e cpu/event=0x1d0/ \
-e cpu/event=0x1c7/ \
-e cpu/umask=0x1f,event=0x18e/ \
-e cpu/umask=0x7,event=0x18e/ \
-e cpu/umask=0x18,event=0x18e/ \
./workload
dmesg will report a #GP warning from an unchecked MSR access
error on MSR_F15H_PERF_CTLx.
This is because according to APM (Revision: 4.03) Figure 13-7,
the bits [35:32] of AMD PerfEvtSeln register is a part of the
event select encoding, which extends the EVENT_SELECT field
from 8 bits to 12 bits.
Opportunistically update pmu->reserved_bits for reserved bit 19.
Reported-by: Jim Mattson <jmattson@google.com>
Fixes: ca724305a2 ("KVM: x86/vPMU: Implement AMD vPMU code for KVM")
Signed-off-by: Like Xu <likexu@tencent.com>
Message-Id: <20211118130320.95997-1-likexu@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 060a0fb721 upstream.
Remove the warn trace message - it's not a correct check here, because
the function can still be called on the device in DOWN state
Fixes: 508f2e3dce ("net: atlantic: split rx and tx per-queue stats")
Signed-off-by: Sameer Saurabh <ssaurabh@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2087ced0fc upstream.
B0 is the main and widespread device revision of atlantic2 HW. In the
current state, driver will incorrectly fetch the statistics for this
revision.
Fixes: 5cfd54d7dc ("net: atlantic: minimal A2 fw_ops")
Signed-off-by: Dmitry Bogdanov <dbezrukov@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 03fa512189 upstream.
Since Half Duplex mode has been deprecated by the firmware, driver should
not advertise Half Duplex speed in ethtool support link speed values.
Fixes: 071a02046c ("net: atlantic: A2: half duplex support")
Signed-off-by: Sameer Saurabh <ssaurabh@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 413d5e09ca upstream.
At the late production stages new dev ids were introduced. These are
now in production, so its important for the driver to recognize these.
And also fix the board caps for AQC115C adapter.
Fixes: b3f0c79cba ("net: atlantic: A2 hw_ops skeleton")
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2465c80223 upstream.
The correct way to reflect firmware version is to use bundle version.
Hence populating the same instead of MAC fw version.
Fixes: c1be0bf092 ("net: atlantic: common functions needed for basic A2 init/deinit hw_ops")
Signed-off-by: Sameer Saurabh <ssaurabh@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa685acd98 upstream.
When 2.5G is advertised, N-Base should be advertised against the T-base
caps. N5G is out of use in baseline code and driver should treat both 5G
and N5G (and also 2.5G and N2.5G) equally from user perspective.
Fixes: 5cfd54d7dc ("net: atlantic: minimal A2 fw_ops")
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa1dcb5646 upstream.
The max waiting period (of 1 ms) while reading the data from FW shared
buffer is too small for certain types of data (e.g., stats). There's a
chance that FW could be updating buffer at the same time and driver
would be unsuccessful in reading data. Firmware manual recommends to
have 1 sec timeout to fix this issue.
Fixes: 5cfd54d7dc ("net: atlantic: minimal A2 fw_ops")
Signed-off-by: Dmitry Bogdanov <dbezrukov@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4840d537c upstream.
In particular, we need to ensure all the necessary blocks are switched
to 64b mode (a5xx+) otherwise the high bits of the address of the BO to
snapshot state into will be ignored, resulting in:
*** gpu fault: ttbr0=0000000000000000 iova=0000000000012000 dir=READ type=TRANSLATION source=CP (0,0,0,0)
platform 506a000.gmu: [drm:a6xx_gmu_set_oob] *ERROR* Timeout waiting for GMU OOB set BOOT_SLUMBER: 0x0
Fixes: 4f776f4511 ("drm/msm/gpu: Convert the GPU show function to use the GPU state")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20211108180122.487859-1-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4d25abf97 upstream.
In commit 142639a52a ("drm/msm/a6xx: fix crashstate capture for
A650") we changed a6xx_get_gmu_registers() to read 3 sets of
registers. Unfortunately, we didn't change the memory allocation for
the array. That leads to a KASAN warning (this was on the chromeos-5.4
kernel, which has the problematic commit backported to it):
BUG: KASAN: slab-out-of-bounds in _a6xx_get_gmu_registers+0x144/0x430
Write of size 8 at addr ffffff80c89432b0 by task A618-worker/209
CPU: 5 PID: 209 Comm: A618-worker Tainted: G W 5.4.156-lockdep #22
Hardware name: Google Lazor Limozeen without Touchscreen (rev5 - rev8) (DT)
Call trace:
dump_backtrace+0x0/0x248
show_stack+0x20/0x2c
dump_stack+0x128/0x1ec
print_address_description+0x88/0x4a0
__kasan_report+0xfc/0x120
kasan_report+0x10/0x18
__asan_report_store8_noabort+0x1c/0x24
_a6xx_get_gmu_registers+0x144/0x430
a6xx_gpu_state_get+0x330/0x25d4
msm_gpu_crashstate_capture+0xa0/0x84c
recover_worker+0x328/0x838
kthread_worker_fn+0x32c/0x574
kthread+0x2dc/0x39c
ret_from_fork+0x10/0x18
Allocated by task 209:
__kasan_kmalloc+0xfc/0x1c4
kasan_kmalloc+0xc/0x14
kmem_cache_alloc_trace+0x1f0/0x2a0
a6xx_gpu_state_get+0x164/0x25d4
msm_gpu_crashstate_capture+0xa0/0x84c
recover_worker+0x328/0x838
kthread_worker_fn+0x32c/0x574
kthread+0x2dc/0x39c
ret_from_fork+0x10/0x18
Fixes: 142639a52a ("drm/msm/a6xx: fix crashstate capture for A650")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20211103153049.1.Idfa574ccb529d17b69db3a1852e49b580132035c@changeid
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 19f36edf14 upstream.
Correct an error where setting /proc/sys/net/rds/tcp/rds_tcp_rcvbuf would
instead modify the socket's sk_sndbuf and would leave sk_rcvbuf untouched.
Fixes: c6a58ffed5 ("RDS: TCP: Add sysctl tunables for sndbuf/rcvbuf on rds-tcp socket")
Signed-off-by: William Kucharski <william.kucharski@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 213f5f8f31 upstream.
Before commit faa041a40b ("ipv4: Create cleanup helper for fib_nh")
changes to net->ipv4.fib_num_tclassid_users were protected by RTNL.
After the change, this is no longer the case, as free_fib_info_rcu()
runs after rcu grace period, without rtnl being held.
Fixes: faa041a40b ("ipv4: Create cleanup helper for fib_nh")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Ahern <dsahern@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f4a8adbfe4 upstream.
The commit c55211892f ("dpaa2-eth: support PTP Sync packet one-step
timestamping") forgets to destroy workqueue at the end of remove
function.
Fix this by adding destroy_workqueue before fsl_mc_portal_free and
free_netdev.
Fixes: c55211892f ("dpaa2-eth: support PTP Sync packet one-step timestamping")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b83f5ac7d9 upstream.
'bitmap_fill()' fills a bitmap one 'long' at a time.
It is likely that an exact number of bits is expected.
Use 'bitmap_set()' instead in order not to set unexpected bits.
Fixes: e531f76757 ("net: mvpp2: handle cases where more CPUs are available than s/w threads")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 817b653160 upstream.
On most systems request for IRQ 0 will fail, phylib will print an error message
and fall back to polling. To fix this set the phydev->irq to PHY_POLL if no IRQ
is available.
Fixes: cc89c323a3 ("lan78xx: Use irq_domain for phy interrupt from USB Int. EP")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Sven Schuchmann <schuchmann@schleissheimer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a05431b22b upstream.
ipv6_addr_bind/ipv4_addr_bind are function names. Previously, bind test
would not be run by default due to the wrong case names
Fixes: 34d0302ab8 ("selftests: Add ipv6 address bind tests to fcnal-test")
Fixes: 75b2b2b3db ("selftests: Add ipv4 address bind tests to fcnal-test")
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit addad76431 upstream.
In mlx4_en_try_alloc_resources(), mlx4_en_copy_priv() is called and
tmp->tx_cq will be freed on the error path of mlx4_en_copy_priv().
After that mlx4_en_alloc_resources() is called and there is a dereference
of &tmp->tx_cq[t][i] in mlx4_en_alloc_resources(), which could lead to
a use after free problem on failure of mlx4_en_copy_priv().
Fix this bug by adding a check of mlx4_en_copy_priv()
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_MLX4_EN=m show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: ec25bc04ed ("net/mlx4_en: Add resilience in low memory systems")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20211130164438.190591-1-zhou1615@umn.edu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 35b6b28e69 upstream.
When branch target identifiers are in use, code reachable via an
indirect branch requires a BTI landing pad at the branch target site.
When building FTRACE_WITH_REGS atop patchable-function-entry, we miss
BTIs at the start start of the `ftrace_caller` and `ftrace_regs_caller`
trampolines, and when these are called from a module via a PLT (which
will use a `BR X16`), we will encounter a BTI failure, e.g.
| # insmod lkdtm.ko
| lkdtm: No crash points registered, enable through debugfs
| # echo function_graph > /sys/kernel/debug/tracing/current_tracer
| # cat /sys/kernel/debug/provoke-crash/DIRECT
| Unhandled 64-bit el1h sync exception on CPU0, ESR 0x34000001 -- BTI
| CPU: 0 PID: 174 Comm: cat Not tainted 5.16.0-rc2-dirty #3
| Hardware name: linux,dummy-virt (DT)
| pstate: 60400405 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=jc)
| pc : ftrace_caller+0x0/0x3c
| lr : lkdtm_debugfs_open+0xc/0x20 [lkdtm]
| sp : ffff800012e43b00
| x29: ffff800012e43b00 x28: 0000000000000000 x27: ffff800012e43c88
| x26: 0000000000000000 x25: 0000000000000000 x24: ffff0000c171f200
| x23: ffff0000c27b1e00 x22: ffff0000c2265240 x21: ffff0000c23c8c30
| x20: ffff8000090ba380 x19: 0000000000000000 x18: 0000000000000000
| x17: 0000000000000000 x16: ffff80001002bb4c x15: 0000000000000000
| x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000900ff0
| x11: ffff0000c4166310 x10: ffff800012e43b00 x9 : ffff8000104f2384
| x8 : 0000000000000001 x7 : 0000000000000000 x6 : 000000000000003f
| x5 : 0000000000000040 x4 : ffff800012e43af0 x3 : 0000000000000001
| x2 : ffff8000090b0000 x1 : ffff0000c171f200 x0 : ffff0000c23c8c30
| Kernel panic - not syncing: Unhandled exception
| CPU: 0 PID: 174 Comm: cat Not tainted 5.16.0-rc2-dirty #3
| Hardware name: linux,dummy-virt (DT)
| Call trace:
| dump_backtrace+0x0/0x1a4
| show_stack+0x24/0x30
| dump_stack_lvl+0x68/0x84
| dump_stack+0x1c/0x38
| panic+0x168/0x360
| arm64_exit_nmi.isra.0+0x0/0x80
| el1h_64_sync_handler+0x68/0xd4
| el1h_64_sync+0x78/0x7c
| ftrace_caller+0x0/0x3c
| do_dentry_open+0x134/0x3b0
| vfs_open+0x38/0x44
| path_openat+0x89c/0xe40
| do_filp_open+0x8c/0x13c
| do_sys_openat2+0xbc/0x174
| __arm64_sys_openat+0x6c/0xbc
| invoke_syscall+0x50/0x120
| el0_svc_common.constprop.0+0xdc/0x100
| do_el0_svc+0x84/0xa0
| el0_svc+0x28/0x80
| el0t_64_sync_handler+0xa8/0x130
| el0t_64_sync+0x1a0/0x1a4
| SMP: stopping secondary CPUs
| Kernel Offset: disabled
| CPU features: 0x0,00000f42,da660c5f
| Memory Limit: none
| ---[ end Kernel panic - not syncing: Unhandled exception ]---
Fix this by adding the required `BTI C`, as we only require these to be
reachable via BL for direct calls or BR X16/X17 for PLTs. For now, these
are open-coded in the function prologue, matching the style of the
`__hwasan_tag_mismatch` trampoline.
In future we may wish to consider adding a new SYM_CODE_START_*()
variant which has an implicit BTI.
When ftrace is built atop mcount, the trampolines are marked with
SYM_FUNC_START(), and so get an implicit BTI. We may need to change
these over to SYM_CODE_START() in future for RELIABLE_STACKTRACE, in
case we need to apply special care aroud the return address being
rewritten.
Fixes: 97fed779f2 ("arm64: bti: Provide Kconfig for kernel mode BTI")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20211129135709.2274019-1-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7e5b9bfa6 upstream.
On ARM v6 and later, we define CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
because the ordinary load/store instructions (ldr, ldrh, ldrb) can
tolerate any misalignment of the memory address. However, load/store
double and load/store multiple instructions (ldrd, ldm) may still only
be used on memory addresses that are 32-bit aligned, and so we have to
use the CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS macro with care, or we
may end up with a severe performance hit due to alignment traps that
require fixups by the kernel. Testing shows that this currently happens
with clang-13 but not gcc-11. In theory, any compiler version can
produce this bug or other problems, as we are dealing with undefined
behavior in C99 even on architectures that support this in hardware,
see also https://gcc.gnu.org/bugzilla/show_bug.cgi?id=100363.
Fortunately, the get_unaligned() accessors do the right thing: when
building for ARMv6 or later, the compiler will emit unaligned accesses
using the ordinary load/store instructions (but avoid the ones that
require 32-bit alignment). When building for older ARM, those accessors
will emit the appropriate sequence of ldrb/mov/orr instructions. And on
architectures that can truly tolerate any kind of misalignment, the
get_unaligned() accessors resolve to the leXX_to_cpup accessors that
operate on aligned addresses.
Since the compiler will in fact emit ldrd or ldm instructions when
building this code for ARM v6 or later, the solution is to use the
unaligned accessors unconditionally on architectures where this is
known to be fast. The _aligned version of the hash function is
however still needed to get the best performance on architectures
that cannot do any unaligned access in hardware.
This new version avoids the undefined behavior and should produce
the fastest hash on all architectures we support.
Link: https://lore.kernel.org/linux-arm-kernel/20181008211554.5355-4-ard.biesheuvel@linaro.org/
Link: https://lore.kernel.org/linux-crypto/CAK8P3a2KfmmGDbVHULWevB0hv71P2oi2ZCHEAqT=8dQfa0=cqQ@mail.gmail.com/
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Fixes: 2c956a6077 ("siphash: add cryptographically secure PRF")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d4741eacd upstream.
There are various problems related to netlink notifications for mpls route
changes in response to interfaces being deleted:
* delete interface of only nexthop
DELROUTE notification is missing RTA_OIF attribute
* delete interface of non-last nexthop
NEWROUTE notification is missing entirely
* delete interface of last nexthop
DELROUTE notification is missing nexthop
All of these problems stem from the fact that existing routes are modified
in-place before sending a notification. Restructure mpls_ifdown() to avoid
changing the route in the DELROUTE cases and to create a copy in the
NEWROUTE case.
Fixes: f8efb73c97 ("mpls: multipath route support")
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e2dabc4f7e upstream.
In qlcnic_83xx_add_rings(), the indirect function of
ahw->hw_ops->alloc_mbx_args will be called to allocate memory for
cmd.req.arg, and there is a dereference of it in qlcnic_83xx_add_rings(),
which could lead to a NULL pointer dereference on failure of the
indirect function like qlcnic_83xx_alloc_mbx_args().
Fix this bug by adding a check of alloc_mbx_args(), this patch
imitates the logic of mbx_cmd()'s failure handling.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_QLCNIC=m show no new warnings, and our
static analyzer no longer warns about this code.
Fixes: 7f9664525f ("qlcnic: 83xx memory map and HW access routine")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Link: https://lore.kernel.org/r/20211130110848.109026-1-zhou1615@umn.edu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dacb5d8875 upstream.
Steffen reported a TCP stream corruption for HTTP requests
served by the apache web-server using a cifs mount-point
and memory mapping the relevant file.
The root cause is quite similar to the one addressed by
commit 20eb4f29b6 ("net: fix sk_page_frag() recursion from
memory reclaim"). Here the nested access to the task page frag
is caused by a page fault on the (mmapped) user-space memory
buffer coming from the cifs file.
The page fault handler performs an smb transaction on a different
socket, inside the same process context. Since sk->sk_allaction
for such socket does not prevent the usage for the task_frag,
the nested allocation modify "under the hood" the page frag
in use by the outer sendmsg call, corrupting the stream.
The overall relevant stack trace looks like the following:
httpd 78268 [001] 3461630.850950: probe:tcp_sendmsg_locked:
ffffffff91461d91 tcp_sendmsg_locked+0x1
ffffffff91462b57 tcp_sendmsg+0x27
ffffffff9139814e sock_sendmsg+0x3e
ffffffffc06dfe1d smb_send_kvec+0x28
[...]
ffffffffc06cfaf8 cifs_readpages+0x213
ffffffff90e83c4b read_pages+0x6b
ffffffff90e83f31 __do_page_cache_readahead+0x1c1
ffffffff90e79e98 filemap_fault+0x788
ffffffff90eb0458 __do_fault+0x38
ffffffff90eb5280 do_fault+0x1a0
ffffffff90eb7c84 __handle_mm_fault+0x4d4
ffffffff90eb8093 handle_mm_fault+0xc3
ffffffff90c74f6d __do_page_fault+0x1ed
ffffffff90c75277 do_page_fault+0x37
ffffffff9160111e page_fault+0x1e
ffffffff9109e7b5 copyin+0x25
ffffffff9109eb40 _copy_from_iter_full+0xe0
ffffffff91462370 tcp_sendmsg_locked+0x5e0
ffffffff91462370 tcp_sendmsg_locked+0x5e0
ffffffff91462b57 tcp_sendmsg+0x27
ffffffff9139815c sock_sendmsg+0x4c
ffffffff913981f7 sock_write_iter+0x97
ffffffff90f2cc56 do_iter_readv_writev+0x156
ffffffff90f2dff0 do_iter_write+0x80
ffffffff90f2e1c3 vfs_writev+0xa3
ffffffff90f2e27c do_writev+0x5c
ffffffff90c042bb do_syscall_64+0x5b
ffffffff916000ad entry_SYSCALL_64_after_hwframe+0x65
The cifs filesystem rightfully sets sk_allocations to GFP_NOFS,
we can avoid the nesting using the sk page frag for allocation
lacking the __GFP_FS flag. Do not define an additional mm-helper
for that, as this is strictly tied to the sk page frag usage.
v1 -> v2:
- use a stricted sk_page_frag() check instead of reordering the
code (Eric)
Reported-by: Steffen Froemer <sfroemer@redhat.com>
Fixes: 5640f76858 ("net: use a per task frag allocator")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b0f38e1597 upstream.
Fix section mismatch warnings in xtsonic. The first one appears to be
bogus and after fixing the second one, the first one is gone.
WARNING: modpost: vmlinux.o(.text+0x529adc): Section mismatch in reference from the function sonic_get_stats() to the function .init.text:set_reset_devices()
The function sonic_get_stats() references
the function __init set_reset_devices().
This is often because sonic_get_stats lacks a __init
annotation or the annotation of set_reset_devices is wrong.
WARNING: modpost: vmlinux.o(.text+0x529b3b): Section mismatch in reference from the function xtsonic_probe() to the function .init.text:sonic_probe1()
The function xtsonic_probe() references
the function __init sonic_probe1().
This is often because xtsonic_probe lacks a __init
annotation or the annotation of sonic_probe1 is wrong.
Fixes: 74f2a5f0ef ("xtensa: Add support for the Sonic Ethernet device for the XT2000 board.")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Chris Zankel <chris@zankel.net>
Cc: linux-xtensa@linux-xtensa.org
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Link: https://lore.kernel.org/r/20211130063947.7529-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b12764695c upstream.
CBUS transfers have always been atomic, but after commit 63b96983a5
("i2c: core: introduce callbacks for atomic transfers") we started to see
warnings during e.g. poweroff as the atomic callback is not explicitly set.
Fix that.
Fixes the following WARNING seen during Nokia N810 power down:
[ 786.570617] reboot: Power down
[ 786.573913] ------------[ cut here ]------------
[ 786.578826] WARNING: CPU: 0 PID: 672 at drivers/i2c/i2c-core.h:40 i2c_smbus_xfer+0x100/0x110
[ 786.587799] No atomic I2C transfer handler for 'i2c-2'
Fixes: 63b96983a5 ("i2c: core: introduce callbacks for atomic transfers")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31b90a95cc upstream.
In case of receiving a NACK, the dma transfer should be stopped
to avoid feeding data into the FIFO.
Also ensure to properly return the proper error code and avoid
waiting for the end of the dma completion in case of
error happening during the transmission.
Fixes: 7ecc8cfde5 ("i2c: i2c-stm32f7: Add DMA support")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c21d02ca4 upstream.
While handling an error during transfer (ex: NACK), it could
happen that the driver has already written data into TXDR
before the transfer get stopped.
This commit add TXDR Flush after end of transfer in case of error to
avoid sending a wrong data on any other slave upon next transfer.
Fixes: aeb068c572 ("i2c: i2c-stm32f7: add driver")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e3fd72171 upstream.
Use 2-factor argument form kvcalloc() instead of kvzalloc().
Link: https://github.com/KSPP/linux/issues/162
Fixes: e7096c131e ("net: WireGuard secure network tunnel")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
[Jason: Gustavo's link above is for KSPP, but this isn't actually a
security fix, as table_size is bounded to 8192 anyway, and gcc realizes
this, so the codegen comes out to be about the same.]
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb32f4f606 upstream.
If we're being delivered packets from multiple CPUs so quickly that the
ring lock is contended for CPU tries, then it's safe to assume that the
queue is near capacity anyway, so just drop the packet rather than
spinning. This helps deal with multicore DoS that can interfere with
data path performance. It _still_ does not completely fix the issue, but
it again chips away at it.
Reported-by: Streun Fabio <fstreun@student.ethz.ch>
Fixes: e7096c131e ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 886fcee939 upstream.
Apparently the spinlock on incoming_handshake's skb_queue is highly
contended, and a torrent of handshake or cookie packets can bring the
data plane to its knees, simply by virtue of enqueueing the handshake
packets to be processed asynchronously. So, we try switching this to a
ring buffer to hopefully have less lock contention. This alleviates the
problem somewhat, though it still isn't perfect, so future patches will
have to improve this further. However, it at least doesn't completely
diminish the data plane.
Reported-by: Streun Fabio <fstreun@student.ethz.ch>
Reported-by: Joel Wanner <joel.wanner@inf.ethz.ch>
Fixes: e7096c131e ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 20ae1d6aa1 upstream.
Each peer's endpoint contains a dst_cache entry that takes a reference
to another netdev. When the containing namespace exits, we take down the
socket and prevent future sockets from being created (by setting
creating_net to NULL), which removes that potential reference on the
netns. However, it doesn't release references to the netns that a netdev
cached in dst_cache might be taking, so the netns still might fail to
exit. Since the socket is gimped anyway, we can simply clear all the
dst_caches (by way of clearing the endpoint src), which will release all
references.
However, the current dst_cache_reset function only releases those
references lazily. But it turns out that all of our usages of
wg_socket_clear_peer_endpoint_src are called from contexts that are not
exactly high-speed or bottle-necked. For example, when there's
connection difficulty, or when userspace is reconfiguring the interface.
And in particular for this patch, when the netns is exiting. So for
those cases, it makes more sense to call dst_release immediately. For
that, we add a small helper function to dst_cache.
This patch also adds a test to netns.sh from Hangbin Liu to ensure this
doesn't regress.
Tested-by: Hangbin Liu <liuhangbin@gmail.com>
Reported-by: Xiumei Mu <xmu@redhat.com>
Cc: Toke Høiland-Jørgensen <toke@redhat.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Fixes: 900575aa33 ("wireguard: device: avoid circular netns references")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 782c72af56 upstream.
We previously removed the restriction on looping to self, and then added
a test to make sure the kernel didn't blow up during a routing loop. The
kernel didn't blow up, thankfully, but on certain architectures where
skb fragmentation is easier, such as ppc64, the skbs weren't actually
being discarded after a few rounds through. But the test wasn't catching
this. So actually test explicitly for massive increases in tx to see if
we have a routing loop. Note that the actual loop problem will need to
be addressed in a different commit.
Fixes: b673e24aad ("wireguard: socket: remove errant restriction on looping to self")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae9287811b upstream.
A __rcu annotation got lost during refactoring, which caused sparse to
become enraged.
Fixes: bf7b042dc6 ("wireguard: allowedips: free empty intermediate nodes when removing single node")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 03ff1b1def upstream.
The selftests currently parse the kernel log at the end to track
potential memory leaks. With these tests now reading off the end of the
buffer, due to recent optimizations, some creation messages were lost,
making the tests think that there was a free without an alloc. Fix this
by increasing the kernel log size.
Fixes: 24b70eeeb4 ("wireguard: use synchronize_net rather than synchronize_rcu")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05b29633c7 upstream.
INVLPG operates on guest virtual address, which are represented by
vcpu->arch.walk_mmu. In nested virtualization scenarios,
kvm_mmu_invlpg() was using the wrong MMU structure; if L2's invlpg were
emulated by L0 (in practice, it hardly happen) when nested two-dimensional
paging is enabled, the call to ->tlb_flush_gva() would be skipped and
the hardware TLB entry would not be invalidated.
Signed-off-by: Lai Jiangshan <laijs@linux.alibaba.com>
Message-Id: <20211124122055.64424-5-jiangshanlai@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f80d15020 upstream.
Having a signed (1 << 31) constant for TCR_EL2_RES1 and CPTR_EL2_TCPAC
causes the upper 32-bit to be set to 1 when assigning them to a 64-bit
variable. Bit 32 in TCR_EL2 is no longer RES0 in ARMv8.7: with FEAT_LPA2
it changes the meaning of bits 49:48 and 9:8 in the stage 1 EL2 page
table entries. As a result of the sign-extension, a non-VHE kernel can
no longer boot on a model with ARMv8.7 enabled.
CPTR_EL2 still has the top 32 bits RES0 but we should preempt any future
problems
Make these top bit constants unsigned as per commit df655b75c4
("arm64: KVM: Avoid setting the upper 32 bits of VTCR_EL2 to 1").
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Chris January <Chris.January@arm.com>
Cc: <stable@vger.kernel.org>
Cc: Will Deacon <will@kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211125152014.2806582-1-catalin.marinas@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 53b7ca1a35 upstream.
Currently, checks for whether VT-d PI can be used refer to the current
status of the feature in the current vCPU; or they more or less pick
vCPU 0 in case a specific vCPU is not available.
However, these checks do not attempt to synchronize with changes to
the IRTE. In particular, there is no path that updates the IRTE when
APICv is re-activated on vCPU 0; and there is no path to wakeup a CPU
that has APICv disabled, if the wakeup occurs because of an IRTE
that points to a posted interrupt.
To fix this, always go through the VT-d PI path as long as there are
assigned devices and APICv is available on both the host and the VM side.
Since the relevant condition was copied over three times, take the hint
and factor it into a separate function.
Suggested-by: Sean Christopherson <seanjc@google.com>
Cc: stable@vger.kernel.org
Reviewed-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: David Matlack <dmatlack@google.com>
Message-Id: <20211123004311.2954158-5-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b4a5a5d56 upstream.
Flush the current VPID when handling KVM_REQ_TLB_FLUSH_GUEST instead of
always flushing vpid01. Any TLB flush that is triggered when L2 is
active is scoped to L2's VPID (if it has one), e.g. if L2 toggles CR4.PGE
and L1 doesn't intercept PGE writes, then KVM's emulation of the TLB
flush needs to be applied to L2's VPID.
Reported-by: Lai Jiangshan <jiangshanlai+lkml@gmail.com>
Fixes: 07ffaf343e ("KVM: nVMX: Sync all PGDs on nested transition with shadow paging")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211125014944.536398-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b285a5587 upstream.
Reject userspace memslots whose size exceeds the storage capacity of an
"unsigned long". KVM's uAPI takes the size as u64 to support large slots
on 64-bit hosts, but does not account for the size being truncated on
32-bit hosts in various flows. The access_ok() check on the userspace
virtual address in particular casts the size to "unsigned long" and will
check the wrong number of bytes.
KVM doesn't actually support slots whose size doesn't fit in an "unsigned
long", e.g. KVM's internal kvm_memory_slot.npages is an "unsigned long",
not a "u64", and misc arch specific code follows that behavior.
Fixes: fa3d315a4c ("KVM: Validate userspace_addr of memslot when registered")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Message-Id: <20211104002531.1176691-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 94ebc03545 upstream.
[Why]
When trying to lightup two 4k60 non-DSC displays behind a branch device
that supports DSC we can't lightup both at once due to bandwidth
limitations - each requires 48 VCPI slots but we only have 63.
[How]
The workaround already exists in the code but is guarded by a CONFIG
that cannot be set by the user and shouldn't need to be.
Check for specific branch device IDs to device whether to enable
the workaround for multiple display scenarios.
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cdef485217 upstream.
The kernel leaks memory when a `fib` rule is present in IPv6 nftables
firewall rules and a suppress_prefix rule is present in the IPv6 routing
rules (used by certain tools such as wg-quick). In such scenarios, every
incoming packet will leak an allocation in `ip6_dst_cache` slab cache.
After some hours of `bpftrace`-ing and source code reading, I tracked
down the issue to ca7a03c417 ("ipv6: do not free rt if
FIB_LOOKUP_NOREF is set on suppress rule").
The problem with that change is that the generic `args->flags` always have
`FIB_LOOKUP_NOREF` set[1][2] but the IPv6-specific flag
`RT6_LOOKUP_F_DST_NOREF` might not be, leading to `fib6_rule_suppress` not
decreasing the refcount when needed.
How to reproduce:
- Add the following nftables rule to a prerouting chain:
meta nfproto ipv6 fib saddr . mark . iif oif missing drop
This can be done with:
sudo nft create table inet test
sudo nft create chain inet test test_chain '{ type filter hook prerouting priority filter + 10; policy accept; }'
sudo nft add rule inet test test_chain meta nfproto ipv6 fib saddr . mark . iif oif missing drop
- Run:
sudo ip -6 rule add table main suppress_prefixlength 0
- Watch `sudo slabtop -o | grep ip6_dst_cache` to see memory usage increase
with every incoming ipv6 packet.
This patch exposes the protocol-specific flags to the protocol
specific `suppress` function, and check the protocol-specific `flags`
argument for RT6_LOOKUP_F_DST_NOREF instead of the generic
FIB_LOOKUP_NOREF when decreasing the refcount, like this.
[1]: ca7a03c417/net/ipv6/fib6_rules.c (L71)
[2]: ca7a03c417/net/ipv6/fib6_rules.c (L99)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215105
Fixes: ca7a03c417 ("ipv6: do not free rt if FIB_LOOKUP_NOREF is set on suppress rule")
Cc: stable@vger.kernel.org
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f48394cf1 upstream.
Trying to remove the fsl-sata module in the PPC64 GNU/Linux
leads to the following warning:
------------[ cut here ]------------
remove_proc_entry: removing non-empty directory 'irq/69',
leaking at least 'fsl-sata[ff0221000.sata]'
WARNING: CPU: 3 PID: 1048 at fs/proc/generic.c:722
.remove_proc_entry+0x20c/0x220
IRQMASK: 0
NIP [c00000000033826c] .remove_proc_entry+0x20c/0x220
LR [c000000000338268] .remove_proc_entry+0x208/0x220
Call Trace:
.remove_proc_entry+0x208/0x220 (unreliable)
.unregister_irq_proc+0x104/0x140
.free_desc+0x44/0xb0
.irq_free_descs+0x9c/0xf0
.irq_dispose_mapping+0x64/0xa0
.sata_fsl_remove+0x58/0xa0 [sata_fsl]
.platform_drv_remove+0x40/0x90
.device_release_driver_internal+0x160/0x2c0
.driver_detach+0x64/0xd0
.bus_remove_driver+0x70/0xf0
.driver_unregister+0x38/0x80
.platform_driver_unregister+0x14/0x30
.fsl_sata_driver_exit+0x18/0xa20 [sata_fsl]
---[ end trace 0ea876d4076908f5 ]---
The driver creates the mapping by calling irq_of_parse_and_map(),
so it also has to dispose the mapping. But the easy way out is to
simply use platform_get_irq() instead of irq_of_parse_map(). Also
we should adapt return value checking and propagate error values.
In this case the mapping is not managed by the device but by
the of core, so the device has not to dispose the mapping.
Fixes: faf0b2e5af ("drivers/ata: add support to Freescale 3.0Gbps SATA Controller")
Cc: stable@vger.kernel.org
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c8ad7e8cf upstream.
When the `rmmod sata_fsl.ko` command is executed in the PPC64 GNU/Linux,
a bug is reported:
==================================================================
BUG: Unable to handle kernel data access on read at 0x80000800805b502c
Oops: Kernel access of bad area, sig: 11 [#1]
NIP [c0000000000388a4] .ioread32+0x4/0x20
LR [80000000000c6034] .sata_fsl_port_stop+0x44/0xe0 [sata_fsl]
Call Trace:
.free_irq+0x1c/0x4e0 (unreliable)
.ata_host_stop+0x74/0xd0 [libata]
.release_nodes+0x330/0x3f0
.device_release_driver_internal+0x178/0x2c0
.driver_detach+0x64/0xd0
.bus_remove_driver+0x70/0xf0
.driver_unregister+0x38/0x80
.platform_driver_unregister+0x14/0x30
.fsl_sata_driver_exit+0x18/0xa20 [sata_fsl]
.__se_sys_delete_module+0x1ec/0x2d0
.system_call_exception+0xfc/0x1f0
system_call_common+0xf8/0x200
==================================================================
The triggering of the BUG is shown in the following stack:
driver_detach
device_release_driver_internal
__device_release_driver
drv->remove(dev) --> platform_drv_remove/platform_remove
drv->remove(dev) --> sata_fsl_remove
iounmap(host_priv->hcr_base); <---- unmap
kfree(host_priv); <---- free
devres_release_all
release_nodes
dr->node.release(dev, dr->data) --> ata_host_stop
ap->ops->port_stop(ap) --> sata_fsl_port_stop
ioread32(hcr_base + HCONTROL) <---- UAF
host->ops->host_stop(host)
The iounmap(host_priv->hcr_base) and kfree(host_priv) functions should
not be executed in drv->remove. These functions should be executed in
host_stop after port_stop. Therefore, we move these functions to the
new function sata_fsl_host_stop and bind the new function to host_stop.
Fixes: faf0b2e5af ("drivers/ata: add support to Freescale 3.0Gbps SATA Controller")
Cc: stable@vger.kernel.org
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 054aa8d439 upstream.
Jann Horn points out that there is another possible race wrt Unix domain
socket garbage collection, somewhat reminiscent of the one fixed in
commit cbcf01128d ("af_unix: fix garbage collect vs MSG_PEEK").
See the extended comment about the garbage collection requirements added
to unix_peek_fds() by that commit for details.
The race comes from how we can locklessly look up a file descriptor just
as it is in the process of being closed, and with the right artificial
timing (Jann added a few strategic 'mdelay(500)' calls to do that), the
Unix domain socket garbage collector could see the reference count
decrement of the close() happen before fget() took its reference to the
file and the file was attached onto a new file descriptor.
This is all (intentionally) correct on the 'struct file *' side, with
RCU lookups and lockless reference counting very much part of the
design. Getting that reference count out of order isn't a problem per
se.
But the garbage collector can get confused by seeing this situation of
having seen a file not having any remaining external references and then
seeing it being attached to an fd.
In commit cbcf01128d ("af_unix: fix garbage collect vs MSG_PEEK") the
fix was to serialize the file descriptor install with the garbage
collector by taking and releasing the unix_gc_lock.
That's not really an option here, but since this all happens when we are
in the process of looking up a file descriptor, we can instead simply
just re-check that the file hasn't been closed in the meantime, and just
re-do the lookup if we raced with a concurrent close() of the same file
descriptor.
Reported-and-tested-by: Jann Horn <jannh@google.com>
Acked-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52d04d4081 upstream.
When running without MIO support, with pci=nomio or for devices which
are not MIO-capable the zPCI subsystem generates pseudo-MMIO addresses
to allow access to PCI BARs via MMIO based Linux APIs even though the
platform uses function handles and BAR numbers.
This is done by stashing an index into our global IOMAP array which
contains the function handle in the 16 most significant bits of the
addresses returned by ioremap() always setting the most significant bit.
On the other hand the MIO addresses assigned by the platform for use,
while requiring special instructions, allow PCI access with virtually
mapped physical addresses. Now the problem is that these MIO addresses
and our own pseudo-MMIO addresses may overlap, while functionally this
would not be a problem by itself this overlap is detected by common code
as both address types are added as resources in the iomem_resource tree.
This leads to the overlapping resource claim of either the MIO capable
or non-MIO capable devices with being rejected.
Since PCI is tightly coupled to the use of the iomem_resource tree, see
for example the code for request_mem_region(), we can't reasonably get
rid of the overlap being detected by keeping our pseudo-MMIO addresses
out of the iomem_resource tree.
Instead let's move the range used by our own pseudo-MMIO addresses by
starting at (1UL << 62) and only using addresses below (1UL << 63) thus
avoiding the range currently used for MIO addresses.
Fixes: c7ff0e918a ("s390/pci: deal with devices that have no support for MIO instructions")
Cc: stable@vger.kernel.org # 5.3+
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c1b5a8466 upstream.
When I hot added a CPU, I found 'cpufreq' directory was not created
below /sys/devices/system/cpu/cpuX/.
It is because get_cpu_device() failed in add_cpu_dev_symlink().
cpufreq_add_dev() is the .add_dev callback of a CPU subsys interface.
It will be called when the CPU device registered into the system.
The call chain is as follows:
register_cpu()
->device_register()
->device_add()
->bus_probe_device()
->cpufreq_add_dev()
But only after the CPU device has been registered, we can get the
CPU device by get_cpu_device(), otherwise it will return NULL.
Since we already have the CPU device in cpufreq_add_dev(), pass
it to add_cpu_dev_symlink().
I noticed that the 'kobj' of the CPU device has been added into
the system before cpufreq_add_dev().
Fixes: 2f0ba790df ("cpufreq: Fix creation of symbolic links to policy directories")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d49eb91e8 upstream.
Currently when removing an ipmi_user the removal is deferred as a work on
the system's workqueue. Although this guarantees the free operation will
occur in non atomic context, it can race with the ipmi_msghandler module
removal (see [1]) . In case a remove_user work is scheduled for removal
and shortly after ipmi_msghandler module is removed we can end up in a
situation where the module is removed fist and when the work is executed
the system crashes with :
BUG: unable to handle page fault for address: ffffffffc05c3450
PF: supervisor instruction fetch in kernel mode
PF: error_code(0x0010) - not-present page
because the pages of the module are gone. In cleanup_ipmi() there is no
easy way to detect if there are any pending works to flush them before
removing the module. This patch creates a separate workqueue and schedules
the remove_work works on it. When removing the module the workqueue is
drained when destroyed to avoid the race.
[1] https://bugs.launchpad.net/bugs/1950666
Cc: stable@vger.kernel.org # 5.1
Fixes: 3b9a907223 (ipmi: fix sleep-in-atomic in free_user at cleanup SRCU user->release_barrier)
Signed-off-by: Ioanna Alifieraki <ioanna-maria.alifieraki@canonical.com>
Message-Id: <20211115131645.25116-1-ioanna-maria.alifieraki@canonical.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6bbfa44116 upstream.
The 'kprobe::data_size' is unsigned, thus it can not be negative. But if
user sets it enough big number (e.g. (size_t)-8), the result of 'data_size
+ sizeof(struct kretprobe_instance)' becomes smaller than sizeof(struct
kretprobe_instance) or zero. In result, the kretprobe_instance are
allocated without enough memory, and kretprobe accesses outside of
allocated memory.
To avoid this issue, introduce a max limitation of the
kretprobe::data_size. 4KB per instance should be OK.
Link: https://lkml.kernel.org/r/163836995040.432120.10322772773821182925.stgit@devnote2
Cc: stable@vger.kernel.org
Fixes: f47cd9b553 ("kprobes: kretprobe user entry-handler")
Reported-by: zhangyue <zhangyue1@kylinos.cn>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee201011c1 upstream.
IPCB/IP6CB need to be initialized when processing outbound v4 or v6 pkts
in the codepath of vrf device xmit function so that leftover garbage
doesn't cause futher code that uses the CB to incorrectly process the
pkt.
One occasion of the issue might occur when MPLS route uses the vrf
device as the outgoing device such as when the route is added using "ip
-f mpls route add <label> dev <vrf>" command.
The problems seems to exist since day one. Hence I put the day one
commits on the Fixes tags.
Fixes: 193125dbd8 ("net: Introduce VRF device driver")
Fixes: 35402e3136 ("net: Add IPv6 support to VRF device")
Cc: stable@vger.kernel.org
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20211130162637.3249-1-ssuryaextr@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7a61432dc8 ]
Possible recursive locking is detected by lockdep when SMC
falls back to TCP. The corresponding warnings are as follows:
============================================
WARNING: possible recursive locking detected
5.16.0-rc1+ #18 Tainted: G E
--------------------------------------------
wrk/1391 is trying to acquire lock:
ffff975246c8e7d8 (&ei->socket.wq.wait){..-.}-{3:3}, at: smc_switch_to_fallback+0x109/0x250 [smc]
but task is already holding lock:
ffff975246c8f918 (&ei->socket.wq.wait){..-.}-{3:3}, at: smc_switch_to_fallback+0xfe/0x250 [smc]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&ei->socket.wq.wait);
lock(&ei->socket.wq.wait);
*** DEADLOCK ***
May be due to missing lock nesting notation
2 locks held by wrk/1391:
#0: ffff975246040130 (sk_lock-AF_SMC){+.+.}-{0:0}, at: smc_connect+0x43/0x150 [smc]
#1: ffff975246c8f918 (&ei->socket.wq.wait){..-.}-{3:3}, at: smc_switch_to_fallback+0xfe/0x250 [smc]
stack backtrace:
Call Trace:
<TASK>
dump_stack_lvl+0x56/0x7b
__lock_acquire+0x951/0x11f0
lock_acquire+0x27a/0x320
? smc_switch_to_fallback+0x109/0x250 [smc]
? smc_switch_to_fallback+0xfe/0x250 [smc]
_raw_spin_lock_irq+0x3b/0x80
? smc_switch_to_fallback+0x109/0x250 [smc]
smc_switch_to_fallback+0x109/0x250 [smc]
smc_connect_fallback+0xe/0x30 [smc]
__smc_connect+0xcf/0x1090 [smc]
? mark_held_locks+0x61/0x80
? __local_bh_enable_ip+0x77/0xe0
? lockdep_hardirqs_on+0xbf/0x130
? smc_connect+0x12a/0x150 [smc]
smc_connect+0x12a/0x150 [smc]
__sys_connect+0x8a/0xc0
? syscall_enter_from_user_mode+0x20/0x70
__x64_sys_connect+0x16/0x20
do_syscall_64+0x34/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
The nested locking in smc_switch_to_fallback() is considered to
possibly cause a deadlock because smc_wait->lock and clc_wait->lock
are the same type of lock. But actually it is safe so far since
there is no other place trying to obtain smc_wait->lock when
clc_wait->lock is held. So the patch replaces spin_lock() with
spin_lock_nested() to avoid false report by lockdep.
Link: https://lkml.org/lkml/2021/11/19/962
Fixes: 2153bd1e3d ("Transfer remaining wait queue entries during fallback")
Reported-by: syzbot+e979d3597f48262cb4ee@syzkaller.appspotmail.com
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Acked-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0fa68da72c ]
The definition of macro MOTO_SROM_BUG is:
#define MOTO_SROM_BUG (lp->active == 8 && (get_unaligned_le32(
dev->dev_addr) & 0x00ffffff) == 0x3e0008)
and the if statement
if (MOTO_SROM_BUG) lp->active = 0;
using this macro indicates lp->active could be 8. If lp->active is 8 and
the second comparison of this macro is false. lp->active will remain 8 in:
lp->phy[lp->active].gep = (*p ? p : NULL); p += (2 * (*p) + 1);
lp->phy[lp->active].rst = (*p ? p : NULL); p += (2 * (*p) + 1);
lp->phy[lp->active].mc = get_unaligned_le16(p); p += 2;
lp->phy[lp->active].ana = get_unaligned_le16(p); p += 2;
lp->phy[lp->active].fdx = get_unaligned_le16(p); p += 2;
lp->phy[lp->active].ttm = get_unaligned_le16(p); p += 2;
lp->phy[lp->active].mci = *p;
However, the length of array lp->phy is 8, so array overflows can occur.
To fix these possible array overflows, we first check lp->active and then
return -EINVAL if it is greater or equal to ARRAY_SIZE(lp->phy) (i.e. 8).
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Teng Qi <starmiku1207184332@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61217be886 ]
In line 5001, if all id in the array 'lp->phy[8]' is not 0, when the
'for' end, the 'k' is 8.
At this time, the array 'lp->phy[8]' may be out of bound.
Signed-off-by: zhangyue <zhangyue1@kylinos.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f9c55c806 ]
The offset value is used in pointer math on skb->data.
Since ipv6_skip_exthdr may return -1 the pointer to uh and th
may not point to the actual udp and tcp headers and potentially
overwrite other stuff. This is why I think this should be checked.
EDIT: added {}'s, thanks Kees
Signed-off-by: Jordy Zomer <jordy@pwning.systems>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a66998e0fb ]
The if statement:
if (port >= DSAF_GE_NUM)
return;
limits the value of port less than DSAF_GE_NUM (i.e., 8).
However, if the value of port is 6 or 7, an array overflow could occur:
port_rst_off = dsaf_dev->mac_cb[port]->port_rst_off;
because the length of dsaf_dev->mac_cb is DSAF_MAX_PORT_NUM (i.e., 6).
To fix this possible array overflow, we first check port and if it is
greater than or equal to DSAF_MAX_PORT_NUM, the function returns.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Teng Qi <starmiku1207184332@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1527f69204 ]
AMD requires that the SATA controller be configured for devsleep in order
for S0i3 entry to work properly.
commit b1a9585cc3 ("ata: ahci: Enable DEVSLP by default on x86 with
SLP_S0") sets up a kernel policy to enable devsleep on Intel mobile
platforms that are using s0ix. Add the PCI ID for the SATA controller in
Green Sardine platforms to extend this policy by default for AMD based
systems using s0i3 as well.
Cc: Nehal-bakulchandra Shah <Nehal-bakulchandra.Shah@amd.com>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214091
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2cf49e00d4 ]
In SRIOV configuration, the reset may failed to bring asic back to normal but stop cpsch
already been called, the start_cpsch will not be called since there is no resume in this
case. When reset been triggered again, driver should avoid to do uninitialization again.
Signed-off-by: shaoyunl <shaoyun.liu@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0c2f8b670 ]
We can race where iscsi_session_recovery_timedout() has woken up the error
handler thread and it's now setting the devices to offline, and
session_recovery_timedout()'s call to scsi_target_unblock() is also trying
to set the device's state to transport-offline. We can then get a mix of
states.
For the case where we can't relogin we want the devices to be in
transport-offline so when we have repaired the connection
__iscsi_unblock_session() can set the state back to running.
Set the device state then call into libiscsi to wake up the error handler.
Link: https://lore.kernel.org/r/20211105221048.6541-2-michael.christie@oracle.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99b63316c3 ]
During the suspend is in process, thermal_zone_device_update bails out
thermal zone re-evaluation for any sensor trip violation without
setting next valid trip to that sensor. It assumes during resume
it will re-evaluate same thermal zone and update trip. But when it is
in suspend temperature goes down and on resume path while updating
thermal zone if temperature is less than previously violated trip,
thermal zone set trip function evaluates the same previous high and
previous low trip as new high and low trip. Since there is no change
in high/low trip, it bails out from thermal zone set trip API without
setting any trip. It leads to a case where sensor high trip or low
trip is disabled forever even though thermal zone has a valid high
or low trip.
During thermal zone device init, reset thermal zone previous high
and low trip. It resolves above mentioned scenario.
Signed-off-by: Manaf Meethalavalappu Pallikunhi <manafm@codeaurora.org>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a91cf0ffbc ]
When a disk has write caching disabled, we skip submission of a bio with
flush and sync requests before writing the superblock, since it's not
needed. However when the integrity checker is enabled, this results in
reports that there are metadata blocks referred by a superblock that
were not properly flushed. So don't skip the bio submission only when
the integrity checker is enabled for the sake of simplicity, since this
is a debug tool and not meant for use in non-debug builds.
fstests/btrfs/220 trigger a check-integrity warning like the following
when CONFIG_BTRFS_FS_CHECK_INTEGRITY=y and the disk with WCE=0.
btrfs: attempt to write superblock which references block M @5242880 (sdb2/5242880/0) which is not flushed out of disk's write cache (block flush_gen=1, dev->flush_gen=0)!
------------[ cut here ]------------
WARNING: CPU: 28 PID: 843680 at fs/btrfs/check-integrity.c:2196 btrfsic_process_written_superblock+0x22a/0x2a0 [btrfs]
CPU: 28 PID: 843680 Comm: umount Not tainted 5.15.0-0.rc5.39.el8.x86_64 #1
Hardware name: Dell Inc. Precision T7610/0NK70N, BIOS A18 09/11/2019
RIP: 0010:btrfsic_process_written_superblock+0x22a/0x2a0 [btrfs]
RSP: 0018:ffffb642afb47940 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000000000002 RCX: 0000000000000000
RDX: 00000000ffffffff RSI: ffff8b722fc97d00 RDI: ffff8b722fc97d00
RBP: ffff8b5601c00000 R08: 0000000000000000 R09: c0000000ffff7fff
R10: 0000000000000001 R11: ffffb642afb476f8 R12: ffffffffffffffff
R13: ffffb642afb47974 R14: ffff8b5499254c00 R15: 0000000000000003
FS: 00007f00a06d4080(0000) GS:ffff8b722fc80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fff5cff5ff0 CR3: 00000001c0c2a006 CR4: 00000000001706e0
Call Trace:
btrfsic_process_written_block+0x2f7/0x850 [btrfs]
__btrfsic_submit_bio.part.19+0x310/0x330 [btrfs]
? bio_associate_blkg_from_css+0xa4/0x2c0
btrfsic_submit_bio+0x18/0x30 [btrfs]
write_dev_supers+0x81/0x2a0 [btrfs]
? find_get_pages_range_tag+0x219/0x280
? pagevec_lookup_range_tag+0x24/0x30
? __filemap_fdatawait_range+0x6d/0xf0
? __raw_callee_save___native_queued_spin_unlock+0x11/0x1e
? find_first_extent_bit+0x9b/0x160 [btrfs]
? __raw_callee_save___native_queued_spin_unlock+0x11/0x1e
write_all_supers+0x1b3/0xa70 [btrfs]
? __raw_callee_save___native_queued_spin_unlock+0x11/0x1e
btrfs_commit_transaction+0x59d/0xac0 [btrfs]
close_ctree+0x11d/0x339 [btrfs]
generic_shutdown_super+0x71/0x110
kill_anon_super+0x14/0x30
btrfs_kill_super+0x12/0x20 [btrfs]
deactivate_locked_super+0x31/0x70
cleanup_mnt+0xb8/0x140
task_work_run+0x6d/0xb0
exit_to_user_mode_prepare+0x1f0/0x200
syscall_exit_to_user_mode+0x12/0x30
do_syscall_64+0x46/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f009f711dfb
RSP: 002b:00007fff5cff7928 EFLAGS: 00000246 ORIG_RAX: 00000000000000a6
RAX: 0000000000000000 RBX: 000055b68c6c9970 RCX: 00007f009f711dfb
RDX: 0000000000000001 RSI: 0000000000000000 RDI: 000055b68c6c9b50
RBP: 0000000000000000 R08: 000055b68c6ca900 R09: 00007f009f795580
R10: 0000000000000000 R11: 0000000000000246 R12: 000055b68c6c9b50
R13: 00007f00a04bf184 R14: 0000000000000000 R15: 00000000ffffffff
---[ end trace 2c4b82abcef9eec4 ]---
S-65536(sdb2/65536/1)
-->
M-1064960(sdb2/1064960/1)
Reviewed-by: Filipe Manana <fdmanana@gmail.com>
Signed-off-by: Wang Yugui <wangyugui@e16-tech.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5dbc4cb466 ]
There is a difference in how architectures treat "mem=" option. For some
that is an amount of online memory, for s390 and x86 this is the limiting
max address. Some memblock api like memblock_enforce_memory_limit()
take limit argument and explicitly treat it as the size of online memory,
and use __find_max_addr to convert it to an actual max address. Current
s390 usage:
memblock_enforce_memory_limit(memblock_end_of_DRAM());
yields different results depending on presence of memory holes (offline
memory blocks in between online memory). If there are no memory holes
limit == max_addr in memblock_enforce_memory_limit() and it does trim
online memory and reserved memory regions. With memory holes present it
actually does nothing.
Since we already use memblock_remove() explicitly to trim online memory
regions to potential limit (think mem=, kdump, addressing limits, etc.)
drop the usage of memblock_enforce_memory_limit() altogether. Trimming
reserved regions should not be required, since we now use
memblock_set_current_limit() to limit allocations and any explicit memory
reservations above the limit is an actual problem we should not hide.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39f5329218 ]
When WWAN device wake from S3 deep, under thinkpad platform,
WWAN would be disabled. This disable status could be checked
by command 'nmcli r wwan' or 'rfkill list'.
Issue analysis as below:
When host resume from S3 deep, thinkpad_acpi driver would
call hotkey_resume() function. Finnaly, it will use
wan_get_status to check the current status of WWAN device.
During this resume progress, wan_get_status would always
return off even WWAN boot up completely.
In patch V2, Hans said 'sw_state should be unchanged
after a suspend/resume. It's better to drop the
tpacpi_rfk_update_swstate call all together from the
resume path'.
And it's confimed by Lenovo that GWAN is no longer
available from WHL generation because the design does not
match with current pin control.
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Link: https://lore.kernel.org/r/20211108060648.8212-1-slark_xiao@163.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6def480181 ]
When kmemdup called failed and register_net_sysctl return NULL, should
return ENOMEM instead of ENOBUFS
Signed-off-by: liuguoqiang <liuguoqiang@uniontech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b922f62259 ]
This bug report shows up when running our research tools. The
reports is SOOB read, but it seems SOOB write is also possible
a few lines below.
In details, fw.len and sw.len are inputs coming from io. A len
over the size of self->rpc triggers SOOB. The patch fixes the
bugs by adding sanity checks.
The bugs are triggerable with compromised/malfunctioning devices.
They are potentially exploitable given they first leak up to
0xffff bytes and able to overwrite the region later.
The patch is tested with QEMU emulater.
This is NOT tested with a real device.
Attached is the log we found by fuzzing.
BUG: KASAN: slab-out-of-bounds in
hw_atl_utils_fw_upload_dwords+0x393/0x3c0 [atlantic]
Read of size 4 at addr ffff888016260b08 by task modprobe/213
CPU: 0 PID: 213 Comm: modprobe Not tainted 5.6.0 #1
Call Trace:
dump_stack+0x76/0xa0
print_address_description.constprop.0+0x16/0x200
? hw_atl_utils_fw_upload_dwords+0x393/0x3c0 [atlantic]
? hw_atl_utils_fw_upload_dwords+0x393/0x3c0 [atlantic]
__kasan_report.cold+0x37/0x7c
? aq_hw_read_reg_bit+0x60/0x70 [atlantic]
? hw_atl_utils_fw_upload_dwords+0x393/0x3c0 [atlantic]
kasan_report+0xe/0x20
hw_atl_utils_fw_upload_dwords+0x393/0x3c0 [atlantic]
hw_atl_utils_fw_rpc_call+0x95/0x130 [atlantic]
hw_atl_utils_fw_rpc_wait+0x176/0x210 [atlantic]
hw_atl_utils_mpi_create+0x229/0x2e0 [atlantic]
? hw_atl_utils_fw_rpc_wait+0x210/0x210 [atlantic]
? hw_atl_utils_initfw+0x9f/0x1c8 [atlantic]
hw_atl_utils_initfw+0x12a/0x1c8 [atlantic]
aq_nic_ndev_register+0x88/0x650 [atlantic]
? aq_nic_ndev_init+0x235/0x3c0 [atlantic]
aq_pci_probe+0x731/0x9b0 [atlantic]
? aq_pci_func_init+0xc0/0xc0 [atlantic]
local_pci_probe+0xd3/0x160
pci_device_probe+0x23f/0x3e0
Reported-by: Brendan Dolan-Gavitt <brendandg@nyu.edu>
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2153bd1e3d ]
The SMC fallback is incomplete currently. There may be some
wait queue entries remaining in smc socket->wq, which should
be removed to clcsocket->wq during the fallback.
For example, in nginx/wrk benchmark, this issue causes an
all-zeros test result:
server: nginx -g 'daemon off;'
client: smc_run wrk -c 1 -t 1 -d 5 http://11.200.15.93/index.html
Running 5s test @ http://11.200.15.93/index.html
1 threads and 1 connections
Thread Stats Avg Stdev Max ± Stdev
Latency 0.00us 0.00us 0.00us -nan%
Req/Sec 0.00 0.00 0.00 -nan%
0 requests in 5.00s, 0.00B read
Requests/sec: 0.00
Transfer/sec: 0.00B
The reason for this all-zeros result is that when wrk used SMC
to replace TCP, it added an eppoll_entry into smc socket->wq
and expected to be notified if epoll events like EPOLL_IN/
EPOLL_OUT occurred on the smc socket.
However, once a fallback occurred, wrk switches to use clcsocket.
Now it is clcsocket->wq instead of smc socket->wq which will
be woken up. The eppoll_entry remaining in smc socket->wq does
not work anymore and wrk stops the test.
This patch fixes this issue by removing remaining wait queue
entries from smc socket->wq to clcsocket->wq during the fallback.
Link: https://www.spinics.net/lists/netdev/msg779769.html
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb162bb2b4 ]
When PHY_SUN6I_MIPI_DPHY is selected, and RESET_CONTROLLER
is not selected, Kbuild gives the following warning:
WARNING: unmet direct dependencies detected for PHY_SUN6I_MIPI_DPHY
Depends on [n]: (ARCH_SUNXI [=n] || COMPILE_TEST [=y]) && HAS_IOMEM [=y] && COMMON_CLK [=y] && RESET_CONTROLLER [=n]
Selected by [y]:
- DRM_SUN6I_DSI [=y] && HAS_IOMEM [=y] && DRM_SUN4I [=y]
This is because DRM_SUN6I_DSI selects PHY_SUN6I_MIPI_DPHY
without selecting or depending on RESET_CONTROLLER, despite
PHY_SUN6I_MIPI_DPHY depending on RESET_CONTROLLER.
These unmet dependency bugs were detected by Kismet,
a static analysis tool for Kconfig. Please advise if this
is not the appropriate solution.
v2:
Fixed indentation to match the rest of the file.
Signed-off-by: Julian Braha <julianbraha@gmail.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20211109032351.43322-1-julianbraha@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3506eee81 ]
Fix the length of holes reported at the end of a file: the length is
relative to the beginning of the extent, not the seek position which is
rounded down to the filesystem block size.
This bug went unnoticed for some time, but is now caught by the
following assertion in iomap_iter_done():
WARN_ON_ONCE(iter->iomap.offset + iter->iomap.length <= iter->pos)
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49462e2be1 ]
Before this patch, evict would clear the iopen glock's gl_object after
releasing the inode glock. In the meantime, another process could reuse
the same block and thus glocks for a new inode. It would lock the inode
glock (exclusively), and then the iopen glock (shared). The shared
locking mode doesn't provide any ordering against the evict, so by the
time the iopen glock is reused, evict may not have gotten to setting
gl_object to NULL.
Fix that by releasing the iopen glock before the inode glock in
gfs2_evict_inode.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>gl_object
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9b91b6b019 upstream.
There's possibility of an ABBA deadlock in case of a splice write to an
overlayfs file and a concurrent splice write to a corresponding real file.
The call chain for splice to an overlay file:
-> do_splice [takes sb_writers on overlay file]
-> do_splice_from
-> iter_file_splice_write [takes pipe->mutex]
-> vfs_iter_write
...
-> ovl_write_iter [takes sb_writers on real file]
And the call chain for splice to a real file:
-> do_splice [takes sb_writers on real file]
-> do_splice_from
-> iter_file_splice_write [takes pipe->mutex]
Syzbot successfully bisected this to commit 82a763e61e ("ovl: simplify
file splice").
Fix by reverting the write part of the above commit and by adding missing
bits from ovl_write_iter() into ovl_splice_write().
Fixes: 82a763e61e ("ovl: simplify file splice")
Reported-and-tested-by: syzbot+579885d1a9a833336209@syzkaller.appspotmail.com
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Cc: Stan Hu <stanhu@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 82a763e61e upstream.
generic_file_splice_read() and iter_file_splice_write() will call back into
f_op->iter_read() and f_op->iter_write() respectively. These already do
the real file lookup and cred override. So the code in ovl_splice_read()
and ovl_splice_write() is redundant.
In addition the ovl_file_accessed() call in ovl_splice_write() is
incorrect, though probably harmless.
Fix by calling generic_file_splice_read() and iter_file_splice_write()
directly.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Cc: Stan Hu <stanhu@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f015d89a4 upstream.
The mechanism in use to allow the client to see the results of COPY/CLONE
is to drop those pages from the pagecache. This forces the client to read
those pages once more from the server. However, truncate_pagecache_range()
zeros out partial pages instead of dropping them. Let us instead use
invalidate_inode_pages2_range() with full-page offsets to ensure the client
properly sees the results of COPY/CLONE operations.
Cc: <stable@vger.kernel.org> # v4.7+
Fixes: 2e72448b07 ("NFS: Add COPY nfs operation")
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Certain transfer ring access patterns can cause the controller to hang
fetching TRBs for a USB2.0 endpoint.
- If two USB2.0 endpoints are active at once and
- Both endpoints are traversing a Link TRB where the following segment
has a lower page address and
- One of the endpoints is a Bulk IN and
- The other endpoint is an Interrupt IN
Then the Interrupt IN endpoint can end up not getting polled.
It is unclear what the precise failure mode is, as the controller seems to
haphazardly and repeatedly fetch TRBs for both endpoints but does not
advance the Interrupt endpoint transfer.
As a workaround, add a quirk that initially constrains all USB2.0 transfer
rings to a single segment in size. If for any reason a device driver queues
up enough outstanding transfers to fill the ring segment, then the ring
will be expanded. This has not been seen to occur with UMS or UVC drivers,
which aggressively queue buffers.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Don't calculate space based on the number of TRBs in the current segment,
as it's OK to wrap to the start (and flip the cycle state bit).
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
In a couple of error/incomplete configuration cases, the
DPI_FORMAT bits wouldn't get set.
Adopt a default of RGB666 in all these cases.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
DRM provides flags for inverting pixel clock and output enable
signals, but these were not mapped to the relevant registers.
Add those mappings.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The "panel-dpi" compatible string configures panel from device tree,
but it doesn't provide any way of configuring the bus format (colour
representation), nor does it populate it.
Add a DT parameter "bus-format" that allows the MEDIA_BUS_FMT_xxx value
to be specified from device tree.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
When using the "panel-dpi" compatible string, desc as passed
from DT is a dumy entry, and panel_dpi_probe allocates a new
one and attaches it to the panel.
However panel_simple_probe has already taken a local copy of
the variable, which means all the validation is done against
the empty dummy structure, not the configured data.
Update the local variable after panel_dpi_probe.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
panel-dpi doesn't know the bit depth, so in the same way that
DPI is guessed for the connector type, guess that it'll be 8bpc.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The clk-bcm2835 handling of the pixel clock does not function
correctly when the HDMI power domain is disabled.
The firmware supports it correctly, and the firmware clock
driver now supports it, so switch the vc4-hdmi driver to use
the firmware clock driver.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The clk-bcm2835 handling of the pixel clock does not function
correctly when the HDMI power domain is disabled.
The firmware supports it correctly, so add it to the
firmware clock driver.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Pi0-3 have power domains attached to the pm_runtime hooks
for the HDMI block. Initialisation done in the reset called
from bind is therefore lost if all users of the domain are
suspended.
The VEC shares the same lowest level clock/power gating as
the HDMI block, so whilst that is enabled the block is never
actually powered down, but if it isn't enabled then we lose
the state.
Reset and initialise the HDMI block from pm_resume.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The commit that changed from dev_err to dev_err_probe left the %d in the
format string, but removed the parameter, leading to a compile
warning.
Fixes: "6505412df625 drm/vc4: Use dev_err_probe when logging error registering HDMI audio"
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Register 0x02 in the FT5x06 is TD_STATUS containing the number
of valid touch points being reported.
Iterate over that number of points rather than all that are
supported on the device.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
This reverts commit 0c41710df5.
The regulator driver is now hopefully fixed, therefore revert the
workaround that dropped the I2C frequency.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The I2C to the Atmel is very fussy, and locks up easily on
Pi0-3 particularly on reads.
If running at 100kHz on Pi3, reading the ID register generally
locks up the Atmel, but splitting the register select write and
read into two transactions is reliable.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The I2C to the Atmel is very fussy, and locks up easily on
Pi0-3 particularly on reads.
The LCD power status is controlled solely by this driver, so
rather than reading it back from the Atmel, use the cached
status last set.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
commit 53af98c091 upstream.
Renoir and newer gfx9 APUs have new TSC register that is
not part of the gfxoff tile, so it can be read without
needing to disable gfx off.
Acked-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a48d96fd5 upstream.
Use __maybe_unused for noirq_suspend()/noirq_resume() hooks to avoid
build warning with !CONFIG_PM_SLEEP:
>> drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:796:12: error: 'stmmac_pltfr_noirq_resume' defined but not used [-Werror=unused-function]
796 | static int stmmac_pltfr_noirq_resume(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~
>> drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:775:12: error: 'stmmac_pltfr_noirq_suspend' defined but not used [-Werror=unused-function]
775 | static int stmmac_pltfr_noirq_suspend(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Fixes: 276aae3772 ("net: stmmac: fix system hang caused by eee_ctrl_timer during suspend/resume")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85b6d24646 upstream.
Currently, the exit_shm() function not designed to work properly when
task->sysvshm.shm_clist holds shm objects from different IPC namespaces.
This is a real pain when sysctl kernel.shm_rmid_forced = 1, because it
leads to use-after-free (reproducer exists).
This is an attempt to fix the problem by extending exit_shm mechanism to
handle shm's destroy from several IPC ns'es.
To achieve that we do several things:
1. add a namespace (non-refcounted) pointer to the struct shmid_kernel
2. during new shm object creation (newseg()/shmget syscall) we
initialize this pointer by current task IPC ns
3. exit_shm() fully reworked such that it traverses over all shp's in
task->sysvshm.shm_clist and gets IPC namespace not from current task
as it was before but from shp's object itself, then call
shm_destroy(shp, ns).
Note: We need to be really careful here, because as it was said before
(1), our pointer to IPC ns non-refcnt'ed. To be on the safe side we
using special helper get_ipc_ns_not_zero() which allows to get IPC ns
refcounter only if IPC ns not in the "state of destruction".
Q/A
Q: Why can we access shp->ns memory using non-refcounted pointer?
A: Because shp object lifetime is always shorther than IPC namespace
lifetime, so, if we get shp object from the task->sysvshm.shm_clist
while holding task_lock(task) nobody can steal our namespace.
Q: Does this patch change semantics of unshare/setns/clone syscalls?
A: No. It's just fixes non-covered case when process may leave IPC
namespace without getting task->sysvshm.shm_clist list cleaned up.
Link: https://lkml.kernel.org/r/67bb03e5-f79c-1815-e2bf-949c67047418@colorfullife.com
Link: https://lkml.kernel.org/r/20211109151501.4921-1-manfred@colorfullife.com
Fixes: ab602f7991 ("shm: make exit_shm work proportional to task activity")
Co-developed-by: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Alexander Mikhalitsyn <alexander.mikhalitsyn@virtuozzo.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Andrei Vagin <avagin@gmail.com>
Cc: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Cc: Vasily Averin <vvs@virtuozzo.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe3d100240 upstream.
We should not walk/touch page tables outside of VMA boundaries when
holding only the mmap sem in read mode. Evil user space can modify the
VMA layout just before this function runs and e.g., trigger races with
page table removal code since commit dd2283f260 ("mm: mmap: zap pages
with read mmap_sem in munmap"). gfn_to_hva() will only translate using
KVM memory regions, but won't validate the VMA.
Further, we should not allocate page tables outside of VMA boundaries: if
evil user space decides to map hugetlbfs to these ranges, bad things will
happen because we suddenly have PTE or PMD page tables where we
shouldn't have them.
Similarly, we have to check if we suddenly find a hugetlbfs VMA, before
calling get_locked_pte().
Fixes: 2d42f94773 ("s390/kvm: Add PGSTE manipulation functions")
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Link: https://lore.kernel.org/r/20210909162248.14969-4-david@redhat.com
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a884daa61a upstream.
Today netfront will trust the backend to send only sane response data.
In order to avoid privilege escalations or crashes in case of malicious
backends verify the data to be within expected limits. Especially make
sure that the response always references an outstanding request.
Note that only the tx queue needs special id handling, as for the rx
queue the id is equal to the index in the ring page.
Introduce a new indicator for the device whether it is broken and let
the device stop working when it is set. Set this indicator in case the
backend sets any weird data.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 21631d2d74 upstream.
The tx_skb_freelist elements are in a single linked list with the
request id used as link reference. The per element link field is in a
union with the skb pointer of an in use request.
Move the link reference out of the union in order to enable a later
reuse of it for requests which need a populated skb pointer.
Rename add_id_to_freelist() and get_id_from_freelist() to
add_id_to_list() and get_id_from_list() in order to prepare using
those for other lists as well. Define ~0 as value to indicate the end
of a list and place that value into the link for a request not being
on the list.
When freeing a skb zero the skb pointer in the request. Use a NULL
value of the skb pointer instead of skb_entry_is_link() for deciding
whether a request has a skb linked to it.
Remove skb_entry_set_link() and open code it instead as it is really
trivial now.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 162081ec33 upstream.
In order to avoid a malicious backend being able to influence the local
processing of a request build the request locally first and then copy
it to the ring page. Any reading from the request influencing the
processing in the frontend needs to be done on the local instance.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8446066bf8 upstream.
In order to avoid problems in case the backend is modifying a response
on the ring page while the frontend has already seen it, just read the
response into a local buffer in one go and then operate on that buffer
only.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b94e4b147f upstream.
Today blkfront will trust the backend to send only sane response data.
In order to avoid privilege escalations or crashes in case of malicious
backends verify the data to be within expected limits. Especially make
sure that the response always references an outstanding request.
Introduce a new state of the ring BLKIF_STATE_ERROR which will be
switched to in case an inconsistency is being detected. Recovering from
this state is possible only via removing and adding the virtual device
again (e.g. via a suspend/resume cycle).
Make all warning messages issued due to valid error responses rate
limited in order to avoid message floods being triggered by a malicious
backend.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Link: https://lore.kernel.org/r/20210730103854.12681-4-jgross@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 629a5d87e2 upstream.
Sync include/xen/interface/io/ring.h with Xen's newest version in
order to get the RING_COPY_RESPONSE() and RING_RESPONSE_PROD_OVERFLOW()
macros.
Note that this will correct the wrong license info by adding the
missing original copyright notice.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6cb206508b upstream.
When pid filtering is activated in an instance, all of the events trace
files for that instance has the PID_FILTER flag set. This determines
whether or not pid filtering needs to be done on the event, otherwise the
event is executed as normal.
If pid filtering is enabled when an event is created (via a dynamic event
or modules), its flag is not updated to reflect the current state, and the
events are not filtered properly.
Cc: stable@vger.kernel.org
Fixes: 3fdaf80f4a ("tracing: Implement event pid filtering")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 71e6864eac ]
Linux allows doing a flush/fsync on a file open for read-only,
but the protocol does not allow that. If the file passed in
on the flush is read-only try to find a writeable handle for
the same inode, if that is not possible skip sending the
fsync call to the server to avoid breaking the apps.
Reported-by: Julian Sikorski <belegdol@gmail.com>
Tested-by: Julian Sikorski <belegdol@gmail.com>
Suggested-by: Jeremy Allison <jra@samba.org>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8cfc0c7ed3 ]
ceph_statfs currently stuffs the cluster fsid into the f_fsid field.
This was fine when we only had a single filesystem per cluster, but now
that we have multiples we need to use something that will vary between
them.
Change ceph_statfs to xor each 32-bit chunk of the fsid (aka cluster id)
into the lower bits of the statfs->f_fsid. Change the lower bits to hold
the fscid (filesystem ID within the cluster).
That should give us a value that is guaranteed to be unique between
filesystems within a cluster, and should minimize the chance of
collisions between mounts of different clusters.
URL: https://tracker.ceph.com/issues/52812
Reported-by: Sachin Prabhu <sprabhu@redhat.com>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Xiubo Li <xiubli@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6663b138de ]
Inconsistent node block will cause a file fail to open or read,
which could make the user process crashes or stucks. Let's mark
SBI_NEED_FSCK flag to trigger a fix at next fsck time. After
unlinking the corrupted file, the user process could regenerate
a new one and work correctly.
Signed-off-by: Weichao Guo <guoweichao@oppo.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dce1ca0525 ]
To hot unplug a CPU, the idle task on that CPU calls a few layers of C
code before finally leaving the kernel. When KASAN is in use, poisoned
shadow is left around for each of the active stack frames, and when
shadow call stacks are in use. When shadow call stacks (SCS) are in use
the task's saved SCS SP is left pointing at an arbitrary point within
the task's shadow call stack.
When a CPU is offlined than onlined back into the kernel, this stale
state can adversely affect execution. Stale KASAN shadow can alias new
stackframes and result in bogus KASAN warnings. A stale SCS SP is
effectively a memory leak, and prevents a portion of the shadow call
stack being used. Across a number of hotplug cycles the idle task's
entire shadow call stack can become unusable.
We previously fixed the KASAN issue in commit:
e1b77c9298 ("sched/kasan: remove stale KASAN poison after hotplug")
... by removing any stale KASAN stack poison immediately prior to
onlining a CPU.
Subsequently in commit:
f1a0a376ca ("sched/core: Initialize the idle task with preemption disabled")
... the refactoring left the KASAN and SCS cleanup in one-time idle
thread initialization code rather than something invoked prior to each
CPU being onlined, breaking both as above.
We fixed SCS (but not KASAN) in commit:
63acd42c0d ("sched/scs: Reset the shadow stack when idle_task_exit")
... but as this runs in the context of the idle task being offlined it's
potentially fragile.
To fix these consistently and more robustly, reset the SCS SP and KASAN
shadow of a CPU's idle task immediately before we online that CPU in
bringup_cpu(). This ensures the idle task always has a consistent state
when it is running, and removes the need to so so when exiting an idle
task.
Whenever any thread is created, dup_task_struct() will give the task a
stack which is free of KASAN shadow, and initialize the task's SCS SP,
so there's no need to specially initialize either for idle thread within
init_idle(), as this was only necessary to handle hotplug cycles.
I've tested this on arm64 with:
* gcc 11.1.0, defconfig +KASAN_INLINE, KASAN_STACK
* clang 12.0.0, defconfig +KASAN_INLINE, KASAN_STACK, SHADOW_CALL_STACK
... offlining and onlining CPUS with:
| while true; do
| for C in /sys/devices/system/cpu/cpu*/online; do
| echo 0 > $C;
| echo 1 > $C;
| done
| done
Fixes: f1a0a376ca ("sched/core: Initialize the idle task with preemption disabled")
Reported-by: Qian Cai <quic_qiancai@quicinc.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Tested-by: Qian Cai <quic_qiancai@quicinc.com>
Link: https://lore.kernel.org/lkml/20211115113310.35693-1-mark.rutland@arm.com/
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0fecb289a ]
A prior patch increased the size of struct tcp_zerocopy_receive
but did not update do_tcp_getsockopt() handling to properly account
for this.
This patch simply reintroduces content erroneously cut from the
referenced prior patch that handles the new struct size.
Fixes: 18fb76ed53 ("net-zerocopy: Copy straggler unaligned data for TCP Rx. zerocopy.")
Signed-off-by: Arjun Roy <arjunroy@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c49a35eedf ]
The driver doesn't support RX timestamping for non-PTP packets, but it
declares that it does. Restrict the reported RX filters to PTP v2 over
L2 and over L4.
Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d2ad993aa ]
When PF is set to multi-TCs and configured mapping relationship between
priorities and TCs, the hardware will active these settings for this PF
and its VFs.
In this case when VF just uses one TC and its rx packets contain priority,
and if the priority is not mapped to TC0, as other TCs of VF is not valid,
hardware always put this kind of packets to the queue 0. It cause this kind
of packets of VF can not be used RSS function.
To fix this problem, set tc mode of all unused TCs of VF to the setting of
TC0, then rx packet with priority which map to unused TC will be direct to
TC0.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 01d9cc2dea ]
Inject error before dev_hold(real_dev) in register_vlan_dev(),
and execute the following testcase:
ip link add dev dummy1 type dummy
ip link add name dummy1.100 link dummy1 type vlan id 100
ip link del dev dummy1
When the dummy netdevice is removed, we will get a WARNING as following:
=======================================================================
refcount_t: decrement hit 0; leaking memory.
WARNING: CPU: 2 PID: 0 at lib/refcount.c:31 refcount_warn_saturate+0xbf/0x1e0
and an endless loop of:
=======================================================================
unregister_netdevice: waiting for dummy1 to become free. Usage count = -1073741824
That is because dev_put(real_dev) in vlan_dev_free() be called without
dev_hold(real_dev) in register_vlan_dev(). It makes the refcnt of real_dev
underflow.
Move the dev_hold(real_dev) to vlan_dev_init() which is the call-back of
ndo_init(). That makes dev_hold() and dev_put() for vlan's real_dev
symmetrical.
Fixes: 563bcbae3b ("net: vlan: fix a UAF in vlan_dev_real_dev()")
Reported-by: Petr Machata <petrm@nvidia.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Link: https://lore.kernel.org/r/20211126015942.2918542-1-william.xuanziyang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3911f73f5 ]
We replace proto_ops whenever TLS is configured for RX. But our
replacement also overrides sendpage_locked, which will crash
unless TX is also configured. Similarly we plug both of those
in for TLS_HW (NIC crypto offload) even tho TLS_HW has a completely
different implementation for TX.
Last but not least we always plug in something based on inet_stream_ops
even though a few of the callbacks differ for IPv6 (getname, release,
bind).
Use a callback building method similar to what we do for struct proto.
Fixes: c46234ebb4 ("tls: RX path for ktls")
Fixes: d4ffb02dee ("net/tls: enable sk_msg redirect to tls socket egress")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 520493f66f ]
We don't support splicing control records. TLS 1.3 changes moved
the record type check into the decrypt if(). The skb may already
be decrypted and still be an alert.
Note that decrypt_skb_update() is idempotent and updates ctx->decrypted
so the if() is pointless.
Reorder the check for decryption errors with the content type check
while touching them. This part is not really a bug, because if
decryption failed in TLS 1.3 content type will be DATA, and for
TLS 1.2 it will be correct. Nevertheless its strange to touch output
before checking if the function has failed.
Fixes: fedf201e12 ("net: tls: Refactor control message handling on recv")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41ce097f71 ]
It hangup when booting Loongson 3A1000 with BOTH
CONFIG_PAGE_SIZE_64KB and CONFIG_MIPS_VA_BITS_48, that it turn
out to use 2-level pgtable instead of 3-level. 64KB page size
with 2-level pgtable only cover 42 bits VA, use 3-level pgtable
to cover all 48 bits VA(55 bits)
Fixes: 1e321fa917 ("MIPS64: Support of at least 48 bits of SEGBITS)
Signed-off-by: Huang Pei <huangpei@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7db5e9e9e5 ]
It turns out that 'decode_configs' -> 'set_ftlb_enable' is called under
c->cputype unset, which leaves FTLB disabled on BOTH 3A2000 and 3A3000
Fix it by calling "decode_configs" after c->cputype is initialized
Fixes: da1bd29742 ("MIPS: Loongson64: Probe CPU features via CPUCFG")
Signed-off-by: Huang Pei <huangpei@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eaeace6077 ]
Oleksandr brought a bug report where netpoll causes trace
messages in the log on igb.
Danielle brought this back up as still occurring, so we'll try
again.
[22038.710800] ------------[ cut here ]------------
[22038.710801] igb_poll+0x0/0x1440 [igb] exceeded budget in poll
[22038.710802] WARNING: CPU: 12 PID: 40362 at net/core/netpoll.c:155 netpoll_poll_dev+0x18a/0x1a0
As Alex suggested, change the driver to return work_done at the
exit of napi_poll, which should be safe to do in this driver
because it is not polling multiple queues in this single napi
context (multiple queues attached to one MSI-X vector). Several
other drivers contain the same simple sequence, so I hope
this will not create new problems.
Fixes: 16eb8815c2 ("igb: Refactor clean_rx_irq to reduce overhead and improve performance")
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Reported-by: Danielle Ratson <danieller@nvidia.com>
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Tested-by: Danielle Ratson <danieller@nvidia.com>
Link: https://lore.kernel.org/r/20211123204000.1597971-1-jesse.brandeburg@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c024b226a4 ]
Submit I/O requests with the IOCB_NOWAIT flag set only if
the underlying filesystem supports it.
Fixes: 50a909db36 ("nvmet: use IOCB_NOWAIT for file-ns buffered I/O")
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ebb0c4b27 ]
The kernel_listen function in smc_listen will fail when all the available
ports are occupied. At this point smc->clcsock->sk->sk_data_ready has
been changed to smc_clcsock_data_ready. When we call smc_listen again,
now both smc->clcsock->sk->sk_data_ready and smc->clcsk_data_ready point
to the smc_clcsock_data_ready function.
The smc_clcsock_data_ready() function calls lsmc->clcsk_data_ready which
now points to itself resulting in an infinite loop.
This patch restores smc->clcsock->sk->sk_data_ready with the old value.
Fixes: a60a2b1e0a ("net/smc: reduce active tcp_listen workers")
Signed-off-by: Guo DaXing <guodaxing@huawei.com>
Acked-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 587acad41f ]
Coverity reports a possible NULL dereferencing problem:
in smc_vlan_by_tcpsk():
6. returned_null: netdev_lower_get_next returns NULL (checked 29 out of 30 times).
7. var_assigned: Assigning: ndev = NULL return value from netdev_lower_get_next.
1623 ndev = (struct net_device *)netdev_lower_get_next(ndev, &lower);
CID 1468509 (#1 of 1): Dereference null return value (NULL_RETURNS)
8. dereference: Dereferencing a pointer that might be NULL ndev when calling is_vlan_dev.
1624 if (is_vlan_dev(ndev)) {
Remove the manual implementation and use netdev_walk_all_lower_dev() to
iterate over the lower devices. While on it remove an obsolete function
parameter comment.
Fixes: cb9d43f677 ("net/smc: determine vlan_id of stacked net_device")
Suggested-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dbae3388ea ]
On mv88e6xxx 1G/2.5G PCS, the SerDes register 4.2001.2 has the following
description:
This register bit indicates when link was lost since the last
read. For the current link status, read this register
back-to-back.
Thus to get current link state, we need to read the register twice.
But doing that in the link change interrupt handler would lead to
potentially ignoring link down events, which we really want to avoid.
Thus this needs to be solved in phylink's resolve, by retriggering
another resolve in the event when PCS reports link down and previous
link was up, and by re-reading PCS state if the previous link was down.
The wrong value is read when phylink requests change from sgmii to
2500base-x mode, and link won't come up. This fixes the bug.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 80662f4fd4 ]
On PHY state change the phylink_resolve() function can read stale
information from the MAC and report incorrect link speed and duplex to
the kernel message log.
Example with a Marvell 88X3310 PHY connected to a SerDes port on Marvell
88E6393X switch:
- PHY driver triggers state change due to PHY interface mode being
changed from 10gbase-r to 2500base-x due to copper change in speed
from 10Gbps to 2.5Gbps, but the PHY itself either hasn't yet changed
its interface to the host, or the interrupt about loss of SerDes link
hadn't arrived yet (there can be a delay of several milliseconds for
this), so we still think that the 10gbase-r mode is up
- phylink_resolve()
- phylink_mac_pcs_get_state()
- this fills in speed=10g link=up
- interface mode is updated to 2500base-x but speed is left at 10Gbps
- phylink_major_config()
- interface is changed to 2500base-x
- phylink_link_up()
- mv88e6xxx_mac_link_up()
- .port_set_speed_duplex()
- speed is set to 10Gbps
- reports "Link is Up - 10Gbps/Full" to dmesg
Afterwards when the interrupt finally arrives for mv88e6xxx, another
resolve is forced in which we get the correct speed from
phylink_mac_pcs_get_state(), but since the interface is not being
changed anymore, we don't call phylink_major_config() but only
phylink_mac_config(), which does not set speed/duplex anymore.
To fix this, we need to force the link down and trigger another resolve
on PHY interface change event.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ddb826c2c9 ]
Usage of phy_ethtool_get_link_ksettings() in the link status change
handler isn't needed, and in combination with the referenced change
it results in a deadlock. Simply remove the call and replace it with
direct access to phydev->speed. The duplex argument of
lan743x_phy_update_flowcontrol() isn't used and can be removed.
Fixes: c10a485c3d ("phy: phy_ethtool_ksettings_get: Lock the phy for consistency")
Reported-by: Alessandro B Maurici <abmaurici@gmail.com>
Tested-by: Alessandro B Maurici <abmaurici@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/40e27f76-0ba3-dcef-ee32-a78b9df38b0f@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e1fddc98d ]
While testing BIG TCP patch series, I was expecting that TCP_RR workloads
with 80KB requests/answers would send one 80KB TSO packet,
then being received as a single GRO packet.
It turns out this was not happening, and the root cause was that
cubic Hystart ACK train was triggering after a few (2 or 3) rounds of RPC.
Hystart was wrongly setting CWND/SSTHRESH to 30, while my RPC
needed a budget of ~20 segments.
Ideally these TCP_RR flows should not exit slow start.
Cubic Hystart should reset itself at each round, instead of assuming
every TCP flow is a bulk one.
Note that even after this patch, Hystart can still trigger, depending
on scheduling artifacts, but at a higher CWND/SSTHRESH threshold,
keeping optimal TSO packet sizes.
Tested:
ip link set dev eth0 gro_ipv6_max_size 131072 gso_ipv6_max_size 131072
nstat -n; netperf -H ... -t TCP_RR -l 5 -- -r 80000,80000 -K cubic; nstat|egrep "Ip6InReceives|Hystart|Ip6OutRequests"
Before:
8605
Ip6InReceives 87541 0.0
Ip6OutRequests 129496 0.0
TcpExtTCPHystartTrainDetect 1 0.0
TcpExtTCPHystartTrainCwnd 30 0.0
After:
8760
Ip6InReceives 88514 0.0
Ip6OutRequests 87975 0.0
Fixes: ae27e98a51 ("[TCP] CUBIC v2.3")
Co-developed-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Link: https://lore.kernel.org/r/20211123202535.1843771-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21431f70f6 ]
[Why]
We're only setting the flags on stream[0]'s planes so this logic fails
if we have more than one stream in the state.
This can cause a page flip timeout with multiple displays in the
configuration.
[How]
Index into the stream_status array using the stream index - it's a 1:1
mapping.
Fixes: cdaae8371a ("drm/amd/display: Handle GPU reset for DC block")
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cefcf24b4d ]
Commit 39fbef4b0f ("PM: hibernate: Get block device exclusively in
swsusp_check()") changed the opening mode of the block device to
(FMODE_READ | FMODE_EXCL).
In the corresponding calls to swsusp_close(), the mode is still just
FMODE_READ which triggers the warning in blkdev_flush_mapping() on
resume from hibernate.
So, use the mode (FMODE_READ | FMODE_EXCL) also when closing the
device.
Fixes: 39fbef4b0f ("PM: hibernate: Get block device exclusively in swsusp_check()")
Signed-off-by: Thomas Zeitlhofer <thomas.zeitlhofer+lkml@ze-it.at>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac13285214 ]
Update NC-SI command handler (both standard and OEM) to take into
account of payload paddings in allocating skb (in case of payload
size is not 32-bit aligned).
The checksum field follows payload field, without taking payload
padding into account can cause checksum being truncated, leading to
dropped packets.
Fixes: fb4ee67529 ("net/ncsi: Add NCSI OEM command support")
Signed-off-by: Kumar Thangavel <thangavel.k@hcl.com>
Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 102110efdf ]
Current nvmet_try_send_ddgst() code does not check whether
all data digest bytes are transmitted, fix this by returning
-EAGAIN if all data digest bytes are not transmitted.
Fixes: 872d26a391 ("nvmet-tcp: add NVMe over TCP target driver")
Signed-off-by: Varun Prakash <varun@chelsio.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b1b62bc1e ]
Currently mvpp2_xdp_setup won't allow attaching XDP program if
mtu > ETH_DATA_LEN (1500).
The mvpp2_change_mtu on the other hand checks whether
MVPP2_RX_PKT_SIZE(mtu) > MVPP2_BM_LONG_PKT_SIZE.
These two checks are semantically different.
Moreover this limit can be increased to MVPP2_MAX_RX_BUF_SIZE, since in
mvpp2_rx we have
xdp.data = data + MVPP2_MH_SIZE + MVPP2_SKB_HEADROOM;
xdp.frame_sz = PAGE_SIZE;
Change the checks to check whether
mtu > MVPP2_MAX_RX_BUF_SIZE
Fixes: 07dd0a7aae ("mvpp2: add basic XDP support")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63b08b1f68 ]
When processing port up/down events generated by the device's firmware,
the driver protects itself from events reported for non-existent local
ports, but not the CPU port (local port 0), which exists, but lacks a
netdev.
This can result in a NULL pointer dereference when calling
netif_carrier_{on,off}().
Fix this by bailing early when processing an event reported for the CPU
port. Problem was only observed when running on top of a buggy emulator.
Fixes: 28b1987ef5 ("mlxsw: spectrum: Register CPU port with devlink")
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 837ec05cfe ]
There are few cases in which an array index queried from a fw register,
is accessed without any validation that it doesn't exceed the array
length.
Add a proper length validation, so accessing memory past the end of an
array will be forbidden.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 606a63c978 ]
The side that actively closed socket, it's clcsock doesn't enter
TIME_WAIT state, but the passive side does it. It should show the same
behavior as TCP sockets.
Consider this, when client actively closes the socket, the clcsock in
server enters TIME_WAIT state, which means the address is occupied and
won't be reused before TIME_WAIT dismissing. If we restarted server, the
service would be unavailable for a long time.
To solve this issue, shutdown the clcsock in [A], perform the TCP active
close progress first, before the passive closed side closing it. So that
the actively closed side enters TIME_WAIT, not the passive one.
Client | Server
close() // client actively close |
smc_release() |
smc_close_active() // PEERCLOSEWAIT1 |
smc_close_final() // abort or closed = 1|
smc_cdc_get_slot_and_msg_send() |
[A] |
|smc_cdc_msg_recv_action() // ACTIVE
| queue_work(smc_close_wq, &conn->close_work)
| smc_close_passive_work() // PROCESSABORT or APPCLOSEWAIT1
| smc_close_passive_abort_received() // only in abort
|
|close() // server recv zero, close
| smc_release() // PROCESSABORT or APPCLOSEWAIT1
| smc_close_active()
| smc_close_abort() or smc_close_final() // CLOSED
| smc_cdc_get_slot_and_msg_send() // abort or closed = 1
smc_cdc_msg_recv_action() | smc_clcsock_release()
queue_work(smc_close_wq, &conn->close_work) | sock_release(tcp) // actively close clc, enter TIME_WAIT
smc_close_passive_work() // PEERCLOSEWAIT1 | smc_conn_free()
smc_close_passive_abort_received() // CLOSED|
smc_conn_free() |
smc_clcsock_release() |
sock_release(tcp) // passive close clc |
Link: https://www.spinics.net/lists/netdev/msg780407.html
Fixes: b38d732477 ("smc: socket closing and linkgroup cleanup")
Signed-off-by: Tony Lu <tonylu@linux.alibaba.com>
Reviewed-by: Wen Gu <guwen@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57bbeacdbe ]
We observed the following deadlock in the stress test under low
memory scenario:
Thread A Thread B
- erofs_shrink_scan
- erofs_try_to_release_workgroup
- erofs_workgroup_try_to_freeze -- A
- z_erofs_do_read_page
- z_erofs_collection_begin
- z_erofs_register_collection
- erofs_insert_workgroup
- xa_lock(&sbi->managed_pslots) -- B
- erofs_workgroup_get
- erofs_wait_on_workgroup_freezed -- A
- xa_erase
- xa_lock(&sbi->managed_pslots) -- B
To fix this, it needs to hold xa_lock before freezing the workgroup
since xarray will be touched then. So let's hold the lock before
accessing each workgroup, just like what we did with the radix tree
before.
[ Gao Xiang: Jianhua Hao also reports this issue at
https://lore.kernel.org/r/b10b85df30694bac8aadfe43537c897a@xiaomi.com ]
Link: https://lore.kernel.org/r/20211118135844.3559-1-huangjianan@oppo.com
Fixes: 64094a0441 ("erofs: convert workstn to XArray")
Reviewed-by: Chao Yu <chao@kernel.org>
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Huang Jianan <huangjianan@oppo.com>
Reported-by: Jianhua Hao <haojianhua1@xiaomi.com>
Signed-off-by: Gao Xiang <xiang@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1005f19b93 ]
When replacing a nexthop group, we must release the IPv6 per-cpu dsts of
the removed nexthop entries after an RCU grace period because they
contain references to the nexthop's net device and to the fib6 info.
With specific series of events[1] we can reach net device refcount
imbalance which is unrecoverable. IPv4 is not affected because dsts
don't take a refcount on the route.
[1]
$ ip nexthop list
id 200 via 2002:db8::2 dev bridge.10 scope link onlink
id 201 via 2002:db8::3 dev bridge scope link onlink
id 203 group 201/200
$ ip -6 route
2001:db8::10 nhid 203 metric 1024 pref medium
nexthop via 2002:db8::3 dev bridge weight 1 onlink
nexthop via 2002:db8::2 dev bridge.10 weight 1 onlink
Create rt6_info through one of the multipath legs, e.g.:
$ taskset -a -c 1 ./pkt_inj 24 bridge.10 2001:db8::10
(pkt_inj is just a custom packet generator, nothing special)
Then remove that leg from the group by replace (let's assume it is id
200 in this case):
$ ip nexthop replace id 203 group 201
Now remove the IPv6 route:
$ ip -6 route del 2001:db8::10/128
The route won't be really deleted due to the stale rt6_info holding 1
refcnt in nexthop id 200.
At this point we have the following reference count dependency:
(deleted) IPv6 route holds 1 reference over nhid 203
nh 203 holds 1 ref over id 201
nh 200 holds 1 ref over the net device and the route due to the stale
rt6_info
Now to create circular dependency between nh 200 and the IPv6 route, and
also to get a reference over nh 200, restore nhid 200 in the group:
$ ip nexthop replace id 203 group 201/200
And now we have a permanent circular dependncy because nhid 203 holds a
reference over nh 200 and 201, but the route holds a ref over nh 203 and
is deleted.
To trigger the bug just delete the group (nhid 203):
$ ip nexthop del id 203
It won't really be deleted due to the IPv6 route dependency, and now we
have 2 unlinked and deleted objects that reference each other: the group
and the IPv6 route. Since the group drops the reference it holds over its
entries at free time (i.e. its own refcount needs to drop to 0) that will
never happen and we get a permanent ref on them, since one of the entries
holds a reference over the IPv6 route it will also never be released.
At this point the dependencies are:
(deleted, only unlinked) IPv6 route holds reference over group nh 203
(deleted, only unlinked) group nh 203 holds reference over nh 201 and 200
nh 200 holds 1 ref over the net device and the route due to the stale
rt6_info
This is the last point where it can be fixed by running traffic through
nh 200, and specifically through the same CPU so the rt6_info (dst) will
get released due to the IPv6 genid, that in turn will free the IPv6
route, which in turn will free the ref count over the group nh 203.
If nh 200 is deleted at this point, it will never be released due to the
ref from the unlinked group 203, it will only be unlinked:
$ ip nexthop del id 200
$ ip nexthop
$
Now we can never release that stale rt6_info, we have IPv6 route with ref
over group nh 203, group nh 203 with ref over nh 200 and 201, nh 200 with
rt6_info (dst) with ref over the net device and the IPv6 route. All of
these objects are only unlinked, and cannot be released, thus they can't
release their ref counts.
Message from syslogd@dev at Nov 19 14:04:10 ...
kernel:[73501.828730] unregister_netdevice: waiting for bridge.10 to become free. Usage count = 3
Message from syslogd@dev at Nov 19 14:04:20 ...
kernel:[73512.068811] unregister_netdevice: waiting for bridge.10 to become free. Usage count = 3
Fixes: 7bf4796dd0 ("nexthops: add support for replace")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8837cbbf85 ]
We need a way to release a fib6_nh's per-cpu dsts when replacing
nexthops otherwise we can end up with stale per-cpu dsts which hold net
device references, so add a new IPv6 stub called fib6_nh_release_dsts.
It must be used after an RCU grace period, so no new dsts can be created
through a group's nexthop entry.
Similar to fib6_nh_release it shouldn't be used if fib6_nh_init has failed
so it doesn't need a dummy stub when IPv6 is not enabled.
Fixes: 7bf4796dd0 ("nexthops: add support for replace")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6da2bbb00 ]
Currently, when user space emits SIOCSHWTSTAMP ioctl calls such as
enabling/disabling timestamping or changing filter settings, the driver
reads the current CLOCK_REALTIME value and programming this into the
NIC's hardware clock. This might be necessary during system
initialization, but at runtime, when the PTP clock has already been
synchronized to a grandmaster, a reset of the timestamp settings might
result in a clock jump. Furthermore, if the clock is also controlled by
phc2sys in automatic mode (where the UTC offset is queried from ptp4l),
that UTC-to-TAI offset (currently 37 seconds in 2021) would be
temporarily reset to 0, and it would take a long time for phc2sys to
readjust so that CLOCK_REALTIME and the PHC are apart by 37 seconds
again.
To address the issue, we introduce a new function called
stmmac_init_tstamp_counter(), which gets called during ndo_open().
It contains the code snippet moved from stmmac_hwtstamp_set() that
manages the time synchronization. Besides, the sub second increment
configuration is also moved here since the related values are hardware
dependent and runtime invariant.
Furthermore, the hardware clock must be kept running even when no time
stamping mode is selected in order to retain the synchronized time base.
That way, timestamping can be enabled again at any time only with the
need to compensate the clock's natural drifting.
As a side effect, this patch fixes the issue that ptp_clock_info::enable
can be called before SIOCSHWTSTAMP and the driver (which looks at
priv->systime_flags) was not prepared to handle that ordering.
Fixes: 92ba688851 ("stmmac: add the support for PTP hw clock driver")
Reported-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Holger Assmann <h.assmann@pengutronix.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 276aae3772 ]
commit 5f58591323 ("net: stmmac: delete the eee_ctrl_timer after
napi disabled"), this patch tries to fix system hang caused by eee_ctrl_timer,
unfortunately, it only can resolve it for system reboot stress test. System
hang also can be reproduced easily during system suspend/resume stess test
when mount NFS on i.MX8MP EVK board.
In stmmac driver, eee feature is combined to phylink framework. When do
system suspend, phylink_stop() would queue delayed work, it invokes
stmmac_mac_link_down(), where to deactivate eee_ctrl_timer synchronizly.
In above commit, try to fix issue by deactivating eee_ctrl_timer obviously,
but it is not enough. Looking into eee_ctrl_timer expire callback
stmmac_eee_ctrl_timer(), it could enable hareware eee mode again. What is
unexpected is that LPI interrupt (MAC_Interrupt_Enable.LPIEN bit) is always
asserted. This interrupt has chance to be issued when LPI state entry/exit
from the MAC, and at that time, clock could have been already disabled.
The result is that system hang when driver try to touch register from
interrupt handler.
The reason why above commit can fix system hang issue in stmmac_release()
is that, deactivate eee_ctrl_timer not just after napi disabled, further
after irq freed.
In conclusion, hardware would generate LPI interrupt when clock has been
disabled during suspend or resume, since hardware is in eee mode and LPI
interrupt enabled.
Interrupts from MAC, MTL and DMA level are enabled and never been disabled
when system suspend, so postpone clocks management from suspend stage to
noirq suspend stage should be more safe.
Fixes: 5f58591323 ("net: stmmac: delete the eee_ctrl_timer after napi disabled")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3bd6b2a838 ]
Use nn->tlv_caps.me_freq_mhz instead of nn->me_freq_mhz to check whether
rx-usecs/tx-usecs is valid.
This is because nn->tlv_caps.me_freq_mhz represents the clock_freq (MHz) of
the flow processing cores (FPC) on the NIC. While nn->me_freq_mhz is not
be set.
Fixes: ce991ab666 ("nfp: read ME frequency from vNIC ctrl memory")
Signed-off-by: Diana Wang <na.wang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e95d8eaee2 ]
The ARCH_FEATURES function ID is a 32-bit SMC call, which returns
a 32-bit result per the SMCCC spec. Current code is doing a 64-bit
comparison against -1 (SMCCC_RET_NOT_SUPPORTED) to detect that the
feature is unimplemented. That check doesn't work in a Hyper-V VM,
where the upper 32-bits are zero as allowed by the spec.
Cast the result as an 'int' so the comparison works. The change also
makes the code consistent with other similar checks in this file.
Fixes: 821b67fa46 ("firmware: smccc: Add ARCH_SOC_ID support")
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee50e67ba0 ]
To compute the rtx timeout schedule_3rdack_retransmission() does multiple
things in the wrong way: srtt_us is measured in usec/8 and the timeout
itself is an absolute value.
Fixes: ec3edaa7ca ("mptcp: Add handling of outgoing MP_JOIN requests")
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <mathew.j.martineau>@linux.intel.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e792779e6b ]
Resolve being able to change static values on VF when adaptive interrupt
moderation is enabled.
This problem is fixed by checking the interrupt settings is not
a combination of change of static value while adaptive interrupt
moderation is turned on.
Without this fix, the user would be able to change static values
on VF with adaptive moderation enabled.
Fixes: 65e87c0398 ("i40evf: support queue-specific settings for interrupt moderation")
Signed-off-by: Nitesh B Venkatesh <nitesh.b.venkatesh@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ee4ba13e0 ]
While looping over shost's sdev list it is possible that one
of the drives is getting removed and its sas_target object is
freed but its sdev object remains intact.
Consequently, a kernel panic can occur while the driver is trying to access
the sas_address field of sas_target object without also checking the
sas_target object for NULL.
Link: https://lore.kernel.org/r/20211117104909.2069-1-sreekanth.reddy@broadcom.com
Fixes: f92363d123 ("[SCSI] mpt3sas: add new driver supporting 12GB SAS")
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3c45824ad ]
The failure to retrieve post-op attributes has no bearing on whether or
not the clone operation itself was successful. We must therefore ignore
the return value of decode_getfattr() when looking at the success or
failure of nfs4_xdr_dec_clone().
Fixes: 36022770de ("nfs42: add CLONE xdr functions")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 451dc48c80 ]
This patch fixes an issue that an u32 netlink value is handled as a
signed enum value which doesn't fit into the range of u32 netlink type.
If it's handled as -1 value some BIT() evaluation ends in a
shift-out-of-bounds issue. To solve the issue we set the to u32 max which
is s32 "-1" value to keep backwards compatibility and let the followed enum
values start counting at 0. This brings the compiler to never handle the
enum as signed and a check if the value is above NL802154_IFTYPE_MAX should
filter -1 out.
Fixes: f3ea5e4423 ("ieee802154: add new interface command")
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20211112030916.685793-1-aahringo@redhat.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 861afeac79 ]
Stream IDs are reused across multiple BackEnd mixers, do not reset the
stream mixers if they are not already set for that particular FrontEnd.
Ex:
amixer cset iface=MIXER,name='SLIMBUS_0_RX Audio Mixer MultiMedia1' 1
would set the MultiMedia1 steam for SLIMBUS_0_RX, however doing below
command will reset previously setup MultiMedia1 stream, because both of them
are using MultiMedia1 PCM stream.
amixer cset iface=MIXER,name='SLIMBUS_2_RX Audio Mixer MultiMedia1' 0
reset the FrontEnd Mixers conditionally to fix this issue.
This is more noticeable in desktop setup, where in alsactl tries to restore
the alsa state and overwriting the previous mixer settings.
Fixes: e3a33673e8 ("ASoC: qdsp6: q6routing: Add q6routing driver")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20211116114721.12517-3-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 98481f3d72 ]
The PCIe host bridge has two interrupt lines, one that goes towards it
PCIE_INTR2 second level interrupt controller and one for its MSI second
level interrupt controller. The first interrupt line is not currently
managed by the driver, which is why it was not a functional problem.
The interrupt-map property was also only listing the PCI_INTA interrupts
when there are also the INTB, C and D.
Reported-by: Jim Quinlan <jim2101024@gmail.com>
Fixes: d5c8dc0d4c ("ARM: dts: bcm2711: Enable PCIe controller")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 40f7342f05 ]
The GPIO controller is also an interrupt controller provider and is
currently missing the appropriate 'interrupt-controller' and
'#interrupt-cells' properties to denote that.
Fixes: fb026d3de3 ("ARM: BCM5301X: Add Broadcom's bus-axi to the DTS file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 754c4050a0 ]
The I2C interrupt controller line is off by 32 because the datasheet
describes interrupt inputs into the GIC which are for Shared Peripheral
Interrupts and are starting at offset 32. The ARM GIC binding expects
the SPI interrupts to be numbered from 0 relative to the SPI base.
Fixes: bb097e3e00 ("ARM: dts: BCM5301X: Add I2C support to the DT")
Tested-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39f6eed4cb ]
Previously the IPv6 addresses in the key were clobbered and the mask was
left unset.
I haven't tested this; I noticed it while skimming the code to
understand an unrelated issue.
Fixes: cfab6dbd0e ("netfilter: flowtable: add tunnel match offload support")
Cc: wenxu <wenxu@ucloud.cn>
Signed-off-by: Will Mortensen <willmo@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c95c07836f ]
We are changing expire_nodest_conn to work even for reused connections when
conn_reuse_mode=0, just as what was done with commit dc7b3eb900 ("ipvs:
Fix reuse connection if real server is dead").
For controlled and persistent connections, the new connection will get the
needed real server depending on the rules in ip_vs_check_template().
Fixes: d752c36457 ("ipvs: allow rescheduling of new connections when port reuse is detected")
Co-developed-by: Chuanqi Liu <legend050709@qq.com>
Signed-off-by: Chuanqi Liu <legend050709@qq.com>
Signed-off-by: yangxingwu <xingwu.yang@gmail.com>
Acked-by: Simon Horman <horms@verge.net.au>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77522ff02f ]
And be consistent in error management for both orig/reply filtering
Fixes: cb8aa9a3af ("netfilter: ctnetlink: add kernel side filtering for dump")
Signed-off-by: Florent Fourcot <florent.fourcot@wifirst.fr>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c1e6311771 upstream.
To clear a user buffer we cannot simply use memset, we have to use
clear_user(). With a virtio-mem device that registers a vmcore_cb and
has some logically unplugged memory inside an added Linux memory block,
I can easily trigger a BUG by copying the vmcore via "cp":
systemd[1]: Starting Kdump Vmcore Save Service...
kdump[420]: Kdump is using the default log level(3).
kdump[453]: saving to /sysroot/var/crash/127.0.0.1-2021-11-11-14:59:22/
kdump[458]: saving vmcore-dmesg.txt to /sysroot/var/crash/127.0.0.1-2021-11-11-14:59:22/
kdump[465]: saving vmcore-dmesg.txt complete
kdump[467]: saving vmcore
BUG: unable to handle page fault for address: 00007f2374e01000
#PF: supervisor write access in kernel mode
#PF: error_code(0x0003) - permissions violation
PGD 7a523067 P4D 7a523067 PUD 7a528067 PMD 7a525067 PTE 800000007048f867
Oops: 0003 [#1] PREEMPT SMP NOPTI
CPU: 0 PID: 468 Comm: cp Not tainted 5.15.0+ #6
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.14.0-27-g64f37cc530f1-prebuilt.qemu.org 04/01/2014
RIP: 0010:read_from_oldmem.part.0.cold+0x1d/0x86
Code: ff ff ff e8 05 ff fe ff e9 b9 e9 7f ff 48 89 de 48 c7 c7 38 3b 60 82 e8 f1 fe fe ff 83 fd 08 72 3c 49 8d 7d 08 4c 89 e9 89 e8 <49> c7 45 00 00 00 00 00 49 c7 44 05 f8 00 00 00 00 48 83 e7 f81
RSP: 0018:ffffc9000073be08 EFLAGS: 00010212
RAX: 0000000000001000 RBX: 00000000002fd000 RCX: 00007f2374e01000
RDX: 0000000000000001 RSI: 00000000ffffdfff RDI: 00007f2374e01008
RBP: 0000000000001000 R08: 0000000000000000 R09: ffffc9000073bc50
R10: ffffc9000073bc48 R11: ffffffff829461a8 R12: 000000000000f000
R13: 00007f2374e01000 R14: 0000000000000000 R15: ffff88807bd421e8
FS: 00007f2374e12140(0000) GS:ffff88807f000000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f2374e01000 CR3: 000000007a4aa000 CR4: 0000000000350eb0
Call Trace:
read_vmcore+0x236/0x2c0
proc_reg_read+0x55/0xa0
vfs_read+0x95/0x190
ksys_read+0x4f/0xc0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
Some x86-64 CPUs have a CPU feature called "Supervisor Mode Access
Prevention (SMAP)", which is used to detect wrong access from the kernel
to user buffers like this: SMAP triggers a permissions violation on
wrong access. In the x86-64 variant of clear_user(), SMAP is properly
handled via clac()+stac().
To fix, properly use clear_user() when we're dealing with a user buffer.
Link: https://lkml.kernel.org/r/20211112092750.6921-1-david@redhat.com
Fixes: 997c136f51 ("fs/proc/vmcore.c: add hook to read_from_oldmem() to check for non-ram pages")
Signed-off-by: David Hildenbrand <david@redhat.com>
Acked-by: Baoquan He <bhe@redhat.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Philipp Rudo <prudo@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f76b36d40b upstream.
Fix multiple link training issues in aardvark driver. The main reason of
these issues was misunderstanding of what certain registers do, since their
names and comments were misleading: before commit 96be36dbff ("PCI:
aardvark: Replace custom macros by standard linux/pci_regs.h macros"), the
pci-aardvark.c driver used custom macros for accessing standard PCIe Root
Bridge registers, and misleading comments did not help to understand what
the code was really doing.
After doing more tests and experiments I've come to the conclusion that the
SPEED_GEN register in aardvark sets the PCIe revision / generation
compliance and forces maximal link speed. Both GEN3 and GEN2 values set the
read-only PCI_EXP_FLAGS_VERS bits (PCIe capabilities version of Root
Bridge) to value 2, while GEN1 value sets PCI_EXP_FLAGS_VERS to 1, which
matches with PCI Express specifications revisions 3, 2 and 1 respectively.
Changing SPEED_GEN also sets the read-only bits PCI_EXP_LNKCAP_SLS and
PCI_EXP_LNKCAP2_SLS to corresponding speed.
(Note that PCI Express rev 1 specification does not define PCI_EXP_LNKCAP2
and PCI_EXP_LNKCTL2 registers and when SPEED_GEN is set to GEN1 (which
also sets PCI_EXP_FLAGS_VERS set to 1), lspci cannot access
PCI_EXP_LNKCAP2 and PCI_EXP_LNKCTL2 registers.)
Changing PCIe link speed can be done via PCI_EXP_LNKCTL2_TLS bits of
PCI_EXP_LNKCTL2 register. Armada 3700 Functional Specifications says that
the default value of PCI_EXP_LNKCTL2_TLS is based on SPEED_GEN value, but
tests showed that the default value is always 8.0 GT/s, independently of
speed set by SPEED_GEN. So after setting SPEED_GEN, we must also set value
in PCI_EXP_LNKCTL2 register via PCI_EXP_LNKCTL2_TLS bits.
Triggering PCI_EXP_LNKCTL_RL bit immediately after setting LINK_TRAINING_EN
bit actually doesn't do anything. Tests have shown that a delay is needed
after enabling LINK_TRAINING_EN bit. As triggering PCI_EXP_LNKCTL_RL
currently does nothing, remove it.
Commit 43fc679ced ("PCI: aardvark: Improve link training") introduced
code which sets SPEED_GEN register based on negotiated link speed from
PCI_EXP_LNKSTA_CLS bits of PCI_EXP_LNKSTA register. This code was added to
fix detection of Compex WLE900VX (Atheros QCA9880) WiFi GEN1 PCIe cards, as
otherwise these cards were "invisible" on PCIe bus (probably because they
crashed). But apparently more people reported the same issues with these
cards also with other PCIe controllers [1] and I was able to reproduce this
issue also with other "noname" WiFi cards based on Atheros QCA9890 chip
(with the same PCI vendor/device ids as Atheros QCA9880). So this is not an
issue in aardvark but rather an issue in Atheros QCA98xx chips. Also, this
issue only exists if the kernel is compiled with PCIe ASPM support, and a
generic workaround for this is to change PCIe Bridge to 2.5 GT/s link speed
via PCI_EXP_LNKCTL2_TLS_2_5GT bits in PCI_EXP_LNKCTL2 register [2], before
triggering PCI_EXP_LNKCTL_RL bit. This workaround also works when SPEED_GEN
is set to value GEN2 (5 GT/s). So remove this hack completely in the
aardvark driver and always set SPEED_GEN to value from 'max-link-speed' DT
property. Fix for Atheros QCA98xx chips is handled separately by patch [2].
These two things (code for triggering PCI_EXP_LNKCTL_RL bit and changing
SPEED_GEN value) also explain why commit 6964494582 ("PCI: aardvark:
Train link immediately after enabling training") somehow fixed detection of
those problematic Compex cards with Atheros chips: if triggering link
retraining (via PCI_EXP_LNKCTL_RL bit) was done immediately after enabling
link training (via LINK_TRAINING_EN), it did nothing. If there was a
specific delay, aardvark HW already initialized PCIe link and therefore
triggering link retraining caused the above issue. Compex cards triggered
link down event and disappeared from the PCIe bus.
Commit f4c7d053d7 ("PCI: aardvark: Wait for endpoint to be ready before
training link") added 100ms sleep before calling 'Start link training'
command and explained that it is a requirement of PCI Express
specification. But the code after this 100ms sleep was not doing 'Start
link training', rather it triggered PCI_EXP_LNKCTL_RL bit via PCIe Root
Bridge to put link into Recovery state.
The required delay after fundamental reset is already done in function
advk_pcie_wait_for_link() which also checks whether PCIe link is up.
So after removing the code which triggers PCI_EXP_LNKCTL_RL bit on PCIe
Root Bridge, there is no need to wait 100ms again. Remove the extra
msleep() call and update comment about the delay required by the PCI
Express specification.
According to Marvell Armada 3700 Functional Specifications, Link training
should be enabled via aardvark register LINK_TRAINING_EN after selecting
PCIe generation and x1 lane. There is no need to disable it prior resetting
card via PERST# signal. This disabling code was introduced in commit
5169a9851d ("PCI: aardvark: Issue PERST via GPIO") as a workaround for
some Atheros cards. It turns out that this also is Atheros specific issue
and affects any PCIe controller, not only aardvark. Moreover this Atheros
issue was triggered by juggling with PCI_EXP_LNKCTL_RL, LINK_TRAINING_EN
and SPEED_GEN bits interleaved with sleeps. Now, after removing triggering
PCI_EXP_LNKCTL_RL, there is no need to explicitly disable LINK_TRAINING_EN
bit. So remove this code too. The problematic Compex cards described in
previous git commits are correctly detected in advk_pcie_train_link()
function even after applying all these changes.
Note that with this patch, and also prior this patch, some NVMe disks which
support PCIe GEN3 with 8 GT/s speed are negotiated only at the lowest link
speed 2.5 GT/s, independently of SPEED_GEN value. After manually triggering
PCI_EXP_LNKCTL_RL bit (e.g. from userspace via setpci), these NVMe disks
change link speed to 5 GT/s when SPEED_GEN was configured to GEN2. This
issue first needs to be properly investigated. I will send a fix in the
future.
On the other hand, some other GEN2 PCIe cards with 5 GT/s speed are
autonomously by HW autonegotiated at full 5 GT/s speed without need of any
software interaction.
Armada 3700 Functional Specifications describes the following steps for
link training: set SPEED_GEN to GEN2, enable LINK_TRAINING_EN, poll until
link training is complete, trigger PCI_EXP_LNKCTL_RL, poll until signal
rate is 5 GT/s, poll until link training is complete, enable ASPM L0s.
The requirement for triggering PCI_EXP_LNKCTL_RL can be explained by the
need to achieve 5 GT/s speed (as changing link speed is done by throw to
recovery state entered by PCI_EXP_LNKCTL_RL) or maybe as a part of enabling
ASPM L0s (but in this case ASPM L0s should have been enabled prior
PCI_EXP_LNKCTL_RL).
It is unknown why the original pci-aardvark.c driver was triggering
PCI_EXP_LNKCTL_RL bit before waiting for the link to be up. This does not
align with neither PCIe base specifications nor with Armada 3700 Functional
Specification. (Note that in older versions of aardvark, this bit was
called incorrectly PCIE_CORE_LINK_TRAINING, so this may be the reason.)
It is also unknown why Armada 3700 Functional Specification says that it is
needed to trigger PCI_EXP_LNKCTL_RL for GEN2 mode, as according to PCIe
base specification 5 GT/s speed negotiation is supposed to be entirely
autonomous, even if initial speed is 2.5 GT/s.
[1] - https://lore.kernel.org/linux-pci/87h7l8axqp.fsf@toke.dk/
[2] - https://lore.kernel.org/linux-pci/20210326124326.21163-1-pali@kernel.org/
Link: https://lore.kernel.org/r/20211005180952.6812-12-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 223dec14a0 upstream.
Commit 43f5c77bcb ("PCI: aardvark: Fix reporting CRS value") fixed
handling of CRS response and when CRSSVE flag was not enabled it marked CRS
response as failed transaction (due to simplicity).
But pci-aardvark.c driver is already waiting up to the PIO_RETRY_CNT count
for PIO config response and so we can with a small change implement
re-issuing of config requests as described in PCIe base specification.
This change implements re-issuing of config requests when response is CRS.
Set upper bound of wait cycles to around PIO_RETRY_CNT, afterwards the
transaction is marked as failed and an all-ones value is returned as
before.
We do this by returning appropriate error codes from function
advk_pcie_check_pio_status(). On CRS we return -EAGAIN and caller then
reissues transaction.
Link: https://lore.kernel.org/r/20211005180952.6812-10-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a55f224ff5 upstream.
If a event is filtered by pid and a trigger that requires processing of
the event to happen is a attached to the event, the discard portion does
not take the pid filtering into account, and the event will then be
recorded when it should not have been.
Cc: stable@vger.kernel.org
Fixes: 3fdaf80f4a ("tracing: Implement event pid filtering")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cf0b0e3712 upstream.
The POWER9 ERAT flush instruction is a SLBIA with IH=7, which is a
reserved value on POWER7/8. On POWER8 this invalidates the SLB entries
above index 0, similarly to SLBIA IH=0.
If the SLB entries are invalidated, and then the guest is bypassed, the
host SLB does not get re-loaded, so the bolted entries above 0 will be
lost. This can result in kernel stack access causing a SLB fault.
Kernel stack access causing a SLB fault was responsible for the infamous
mega bug (search "Fix SLB reload bug"). Although since commit
48e7b76957 ("powerpc/64s/hash: Convert SLB miss handlers to C") that
starts using the kernel stack in the SLB miss handler, it might only
result in an infinite loop of SLB faults. In any case it's a bug.
Fix this by only executing the instruction on >= POWER9 where IH=7 is
defined not to invalidate the SLB. POWER7/8 don't require this ERAT
flush.
Fixes: 5008711259 ("KVM: PPC: Book3S HV: Invalidate ERAT when flushing guest TLB entries")
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211119031627.577853-1-npiggin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 36e8f60f08 upstream.
If the xenstore page hasn't been allocated properly, reading the value
of the related hvm_param (HVM_PARAM_STORE_PFN) won't actually return
error. Instead, it will succeed and return zero. Instead of attempting
to xen_remap a bad guest physical address, detect this condition and
return early.
Note that although a guest physical address of zero for
HVM_PARAM_STORE_PFN is theoretically possible, it is not a good choice
and zero has never been validly used in that capacity.
Also recognize all bits set as an invalid value.
For 32-bit Linux, any pfn above ULONG_MAX would get truncated. Pfns
above ULONG_MAX should never be passed by the Xen tools to HVM guests
anyway, so check for this condition and return early.
Cc: stable@vger.kernel.org
Signed-off-by: Stefano Stabellini <stefano.stabellini@xilinx.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Link: https://lore.kernel.org/r/20211123210748.1910236-1-sstabellini@kernel.org
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08f6c2b09e upstream.
In case of errors in xenbus_init (e.g. missing xen_store_gfn parameter),
we goto out_error but we forget to reset xen_store_domain_type to
XS_UNKNOWN. As a consequence xenbus_probe_initcall and other initcalls
will still try to initialize xenstore resulting into a crash at boot.
[ 2.479830] Call trace:
[ 2.482314] xb_init_comms+0x18/0x150
[ 2.486354] xs_init+0x34/0x138
[ 2.489786] xenbus_probe+0x4c/0x70
[ 2.498432] xenbus_probe_initcall+0x2c/0x7c
[ 2.503944] do_one_initcall+0x54/0x1b8
[ 2.507358] kernel_init_freeable+0x1ac/0x210
[ 2.511617] kernel_init+0x28/0x130
[ 2.516112] ret_from_fork+0x10/0x20
Cc: <Stable@vger.kernel.org>
Cc: jbeulich@suse.com
Signed-off-by: Stefano Stabellini <stefano.stabellini@xilinx.com>
Link: https://lore.kernel.org/r/20211115222719.2558207-1-sstabellini@kernel.org
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 473441720c upstream.
Checking buf->flags should be done before the pipe_buf_release() is called
on the pipe buffer, since releasing the buffer might modify the flags.
This is exactly what page_cache_pipe_buf_release() does, and which results
in the same VM_BUG_ON_PAGE(PageLRU(page)) that the original patch was
trying to fix.
Reported-by: Justin Forbes <jmforbes@linuxtx.org>
Fixes: 712a951025 ("fuse: fix page stealing")
Cc: <stable@vger.kernel.org> # v2.6.35
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7fb0413baa upstream.
The HID descriptor of many of Wacom's touch input devices include a
"Confidence" usage that signals if a particular touch collection contains
useful data. The driver does not look at this flag, however, which causes
even invalid contacts to be reported to userspace. A lucky combination of
kernel event filtering and device behavior (specifically: contact ID 0 ==
invalid, contact ID >0 == valid; and order all data so that all valid
contacts are reported before any invalid contacts) spare most devices from
any visibly-bad behavior.
The DTH-2452 is one example of an unlucky device that misbehaves. It uses
ID 0 for both the first valid contact and all invalid contacts. Because
we report both the valid and invalid contacts, the kernel reports that
contact 0 first goes down (valid) and then goes up (invalid) in every
report. This causes ~100 clicks per second simply by touching the screen.
This patch inroduces new `confidence` flag in our `hid_data` structure.
The value is initially set to `true` at the start of a report and can be
set to `false` if an invalid touch usage is seen.
Link: https://github.com/linuxwacom/input-wacom/issues/270
Fixes: f8b6a74719 ("HID: wacom: generic: Support multiple tools per report")
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Tested-by: Joshua Dickens <joshua.dickens@wacom.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98400ad75e upstream.
This reverts commit 279917e27e.
With the CONFIG_HARDENED_USERCOPY option enabled, this patch triggers
kernel bugs at runtime:
usercopy: Kernel memory overwrite attempt detected to kernel text (offset 2084839, size 6)!
kernel BUG at mm/usercopy.c:99!
Backtrace:
IAOQ[0]: usercopy_abort+0xc4/0xe8
[<00000000406ed1c8>] __check_object_size+0x174/0x238
[<00000000407086d4>] copy_strings.isra.0+0x3e8/0x708
[<0000000040709a20>] do_execveat_common.isra.0+0x1bc/0x328
[<000000004070b760>] compat_sys_execve+0x7c/0xb8
[<0000000040303eb8>] syscall_exit+0x0/0x14
The problem is, that we have an init section of at least 2MB size which
starts at _stext and is freed after bootup.
If then later some kernel data is (temporarily) stored in this free
memory, check_kernel_text_object() will trigger a bug since the data
appears to be inside the kernel text (>=_stext) area:
if (overlaps(ptr, len, _stext, _etext))
usercopy_abort("kernel text");
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@kernel.org # 5.4+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13cbaa4c2b upstream.
When the reply for a non-blocking transmit arrives, the sequence
field for that reply was never filled in, so userspace would have no
way of associating the reply to the original transmit.
Copy the sequence field to ensure that this is now possible.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 0dbacebede ([media] cec: move the CEC framework out of staging and to media)
Cc: <stable@vger.kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 174a7fb385 upstream.
This applies a SND_PCI_QUIRK(...) to the ASRock NUC Box 1100 series. This
fixes the issue of the headphone jack not being detected unless warm
rebooted from a certain other OS.
When booting a certain other OS some coeff settings are changed that enable
the audio jack. These settings are preserved on a warm reboot and can be
easily dumped.
The relevant indexes and values where gathered by naively diff-ing and
reading a working and a non-working coeff dump.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211112110704.1022501-1-wse@tuxedocomputers.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 76c4718322 upstream.
The master and next_conj of rcs_ops are used for iterating the
resource list entries, and currently those are supposed to return the
current value. The problem is that next_conf may go over the last
entry before the loop abort condition is evaluated, and it may return
the "current" value that is beyond the array size. It was caught
recently as a GPF, for example.
Those return values are, however, never actually evaluated, hence
basically we don't have to consider the current value as the return at
all. By dropping those return values, the potential out-of-range
access above is also fixed automatically.
This patch changes the return type of master and next_conj callbacks
to void and drop the superfluous code accordingly.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214985
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211118215729.26257-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ae6dc22d2 upstream.
xHC hardware can only have one slot in default state with address 0
waiting for a unique address at a time, otherwise "undefined behavior
may occur" according to xhci spec 5.4.3.4
The address0_mutex exists to prevent this across both xhci roothubs.
If hub_port_init() fails, it may unlock the mutex and exit with a xhci
slot in default state. If the other xhci roothub calls hub_port_init()
at this point we end up with two slots in default state.
Make sure the address0_mutex protects the slot default state across
hub_port_init() retries, until slot is addressed or disabled.
Note, one known minor case is not fixed by this patch.
If device needs to be reset during resume, but fails all hub_port_init()
retries in usb_reset_and_verify_device(), then it's possible the slot is
still left in default state when address0_mutex is unlocked.
Cc: <stable@vger.kernel.org>
Fixes: 638139eb95 ("usb: hub: allow to process more usb hub events in parallel")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211115221630.871204-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 362468830d upstream.
The code that enables either BC_LVL or COMP_CHNG interrupt in tcpm_set_cc
wrongly assumes that the interrupt is unmasked by writing 1 to the apropriate
bit in the mask register. In fact, interrupts are enabled when the mask
is 0, so the tcpm_set_cc enables interrupt for COMP_CHNG when it expects
BC_LVL interrupt to be enabled.
This causes inability of the driver to recognize cable unplug events
in host mode (unplug is recognized only via a COMP_CHNG interrupt).
In device mode this bug was masked by simultaneous triggering of the VBUS
change interrupt, because of loss of VBUS when the port peer is providing
power.
Fixes: 48242e3053 ("usb: typec: fusb302: Revert "Resolve fixed power role contract setup"")
Cc: stable <stable@vger.kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Ondrej Jirman <megous@megous.com>
Link: https://lore.kernel.org/r/20211108102833.2793803-1-megous@megous.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63c4c320cc upstream.
The programming guide noted that the driver needs to verify if the link
state is in U0 before executing the Start Transfer command. If it's not
in U0, the driver needs to perform remote wakeup. This is not accurate.
If the link state is in U1/U2, then the controller will not respond to
link recovery request from DCTL.ULSTCHNGREQ. The Start Transfer command
will trigger a link recovery if it is in U1/U2. A clarification will be
added to the programming guide for all controller versions.
The current implementation shouldn't cause any functional issue. It may
occasionally report an invalid time out warning from failed link
recovery request. The driver will still go ahead with the Start Transfer
command if the remote wakeup fails. The new change only initiates remote
wakeup where it is needed, which is when the link state is in L1/L2/U3.
Fixes: c36d8e947a ("usb: dwc3: gadget: put link to U0 before Start Transfer")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/05b4a5fbfbd0863fc9b1d7af934a366219e3d0b4.1635204761.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 310780e825 upstream.
A new commit in LLVM causes an error on the use of 'long double' when
'-mno-x87' is used, which the kernel does through an alias,
'-mno-80387' (see the LLVM commit below for more details around why it
does this).
drivers/usb/dwc2/hcd_queue.c:1744:25: error: expression requires 'long double' type support, but target 'x86_64-unknown-linux-gnu' does not support it
delay = ktime_set(0, DWC2_RETRY_WAIT_DELAY);
^
drivers/usb/dwc2/hcd_queue.c:62:34: note: expanded from macro 'DWC2_RETRY_WAIT_DELAY'
#define DWC2_RETRY_WAIT_DELAY (1 * 1E6L)
^
1 error generated.
This happens due to the use of a 'long double' literal. The 'E6' part of
'1E6L' causes the literal to be a 'double' then the 'L' suffix promotes
it to 'long double'.
There is no visible reason for a floating point value in this driver, as
the value is only used as a parameter to a function that expects an
integer type. Use NSEC_PER_MSEC, which is the same integer value as
'1E6L', to avoid changing functionality but fix the error.
Link: https://github.com/ClangBuiltLinux/linux/issues/1497
Link: a8083d42b1
Fixes: 6ed30a7d8e ("usb: dwc2: host: use hrtimer for NAK retries")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: John Keeping <john@metanate.com>
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20211105145802.2520658-1-nathan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ad4a0b1d4 upstream.
Added updating of request frame number for elapsed frames,
otherwise frame number will remain as previous use of request.
This will allow function driver to correctly track frames in
case of Missed ISOC occurs.
Added setting request actual length to 0 for elapsed frames.
In Slave mode when pushing data to RxFIFO by dwords, request
actual length incrementing accordingly. But before whole packet
will be pushed into RxFIFO and send to host can occurs Missed
ISOC and data will not send to host. So, in this case request
actual length should be reset to 0.
Fixes: 91bb163e1e ("usb: dwc2: gadget: Fix ISOC flow for BDMA and Slave")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: John Keeping <john@metanate.com>
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/c356baade6e9716d312d43df08d53ae557cb8037.1636011277.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9054fc6d57 upstream.
Printk modifier %pfw is used to print the full path of the device name.
This is obtained device by device until a device no longer has a parent.
On ACPI getting the parent fwnode is done by calling acpi_get_parent()
which tries to down() a semaphore. But local IRQs are now disabled in
vprintk_store() before the mutex is acquired. This is obviously a problem.
Luckily struct device, embedded in struct acpi_device, has a parent field
already. Use that field to get the parent instead of relying on
acpi_get_parent().
Fixes: 3bd32d6a2e ("lib/vsprintf: Add %pfw conversion specifier for printing fwnode names")
Cc: 5.5+ <stable@vger.kernel.org> # 5.5+
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 353050be4c upstream.
Commit a23740ec43 ("bpf: Track contents of read-only maps as scalars") is
checking whether maps are read-only both from BPF program side and user space
side, and then, given their content is constant, reading out their data via
map->ops->map_direct_value_addr() which is then subsequently used as known
scalar value for the register, that is, it is marked as __mark_reg_known()
with the read value at verification time. Before a23740ec43, the register
content was marked as an unknown scalar so the verifier could not make any
assumptions about the map content.
The current implementation however is prone to a TOCTOU race, meaning, the
value read as known scalar for the register is not guaranteed to be exactly
the same at a later point when the program is executed, and as such, the
prior made assumptions of the verifier with regards to the program will be
invalid which can cause issues such as OOB access, etc.
While the BPF_F_RDONLY_PROG map flag is always fixed and required to be
specified at map creation time, the map->frozen property is initially set to
false for the map given the map value needs to be populated, e.g. for global
data sections. Once complete, the loader "freezes" the map from user space
such that no subsequent updates/deletes are possible anymore. For the rest
of the lifetime of the map, this freeze one-time trigger cannot be undone
anymore after a successful BPF_MAP_FREEZE cmd return. Meaning, any new BPF_*
cmd calls which would update/delete map entries will be rejected with -EPERM
since map_get_sys_perms() removes the FMODE_CAN_WRITE permission. This also
means that pending update/delete map entries must still complete before this
guarantee is given. This corner case is not an issue for loaders since they
create and prepare such program private map in successive steps.
However, a malicious user is able to trigger this TOCTOU race in two different
ways: i) via userfaultfd, and ii) via batched updates. For i) userfaultfd is
used to expand the competition interval, so that map_update_elem() can modify
the contents of the map after map_freeze() and bpf_prog_load() were executed.
This works, because userfaultfd halts the parallel thread which triggered a
map_update_elem() at the time where we copy key/value from the user buffer and
this already passed the FMODE_CAN_WRITE capability test given at that time the
map was not "frozen". Then, the main thread performs the map_freeze() and
bpf_prog_load(), and once that had completed successfully, the other thread
is woken up to complete the pending map_update_elem() which then changes the
map content. For ii) the idea of the batched update is similar, meaning, when
there are a large number of updates to be processed, it can increase the
competition interval between the two. It is therefore possible in practice to
modify the contents of the map after executing map_freeze() and bpf_prog_load().
One way to fix both i) and ii) at the same time is to expand the use of the
map's map->writecnt. The latter was introduced in fc9702273e ("bpf: Add mmap()
support for BPF_MAP_TYPE_ARRAY") and further refined in 1f6cb19be2 ("bpf:
Prevent re-mmap()'ing BPF map as writable for initially r/o mapping") with
the rationale to make a writable mmap()'ing of a map mutually exclusive with
read-only freezing. The counter indicates writable mmap() mappings and then
prevents/fails the freeze operation. Its semantics can be expanded beyond
just mmap() by generally indicating ongoing write phases. This would essentially
span any parallel regular and batched flavor of update/delete operation and
then also have map_freeze() fail with -EBUSY. For the check_mem_access() in
the verifier we expand upon the bpf_map_is_rdonly() check ensuring that all
last pending writes have completed via bpf_map_write_active() test. Once the
map->frozen is set and bpf_map_write_active() indicates a map->writecnt of 0
only then we are really guaranteed to use the map's data as known constants.
For map->frozen being set and pending writes in process of still being completed
we fall back to marking that register as unknown scalar so we don't end up
making assumptions about it. With this, both TOCTOU reproducers from i) and
ii) are fixed.
Note that the map->writecnt has been converted into a atomic64 in the fix in
order to avoid a double freeze_mutex mutex_{un,}lock() pair when updating
map->writecnt in the various map update/delete BPF_* cmd flavors. Spanning
the freeze_mutex over entire map update/delete operations in syscall side
would not be possible due to then causing everything to be serialized.
Similarly, something like synchronize_rcu() after setting map->frozen to wait
for update/deletes to complete is not possible either since it would also
have to span the user copy which can sleep. On the libbpf side, this won't
break d66562fba1 ("libbpf: Add BPF object skeleton support") as the
anonymous mmap()-ed "map initialization image" is remapped as a BPF map-backed
mmap()-ed memory where for .rodata it's non-writable.
Fixes: a23740ec43 ("bpf: Track contents of read-only maps as scalars")
Reported-by: w1tcher.bupt@gmail.com
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
[fix conflict to call bpf_map_write_active_dec() in err_put block.
fix conflict to insert new functions after find_and_alloc_map().]
Reference: CVE-2021-4001
Signed-off-by: Masami Ichikawa(CIP) <masami.ichikawa@cybertrust.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a dummy buffer is still active on a frame start, it indicates that this frame
will be dropped. The explicit logging helps users identify performance issues.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Deinterlace and decode aren't affected in the same way as encode
and ISP by the alignment requirement on 3 plane YUV420.
Decode would be affected, but it always aligns the height up to
a macroblock, and uses the selection API to reflect that.
Add in the facility to set the bytesperline alignment per role.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Remove min_buffers_needed=1 from src queue init. Src buffers are bound
to media requests therefore this setting is not needed and generates
a WARN in kernel 5.16.
Signed-off-by: John Cox <jc@kynesim.co.uk>
Matching https://github.com/raspberrypi/linux/pull/4419, the ISP
block (which is also used on the input of the encoder, and output
of the decoder) needs the base address of all planes to be aligned
to multiples of 32. This includes the chroma planes of YUV420 and
YVU420.
If the height is only a multiple of 2 (not 4), then you get an odd
number of lines in the second plane, which means the 3rd plane
starts at a multiple of bytesperline/2.
Set the minimum bytesperline alignment to 64 for those formats
so that the plane alignment is always right.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Avoid logging a spurious error message with error -517
(-EPROBE_DEFER) whilst trying to load HDMI audio.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Whilst investigations continue as to why the 7" DSI screen doesn't
work on Pi3 with KMS, drop the I2C baudrate to 50kHz as that seems
to be a reliable workaround.
This will be reverted once the full issue is understood.
https://github.com/raspberrypi/linux/issues/4686
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Whilst all the datasheets describe FT5x06 as supporting "up to
10 points of absolution X and Y coordinates", the driver
implementation for the compatible string "edt,edt-ft5x06" only
allows for 5.
Switch to the "edt,edt-ft5506" compatible string which allows for
10 points with no other differences.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The ft5x06 is unreliable in sending touch up events, so some
touch IDs can become stuck in the detected state.
Ensure that IDs that are unreported by the controller are
released.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The Pi 4B dts file has had numerous updates since the Pi 400 and CM4
dts files were written. Apply those updates to the other files to
minimise the differences. The change is largely cosmetic, except for
the PCI "device-type" to "device_type" rename, and the correction of
the labels on the Pi 400 GPIO expander pins.
Also set the wifi-2.4ghz-coexistence property on RPi 4 B, which appears
to have been missed.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The existing logic was flawed in that it could try reading the
2711 specific registers for HPD on a CM1/3 where the HPD GPIO
hadn't been defined in DT.
Ensure we don't do the 2711 register read on invalid hardware,
and then
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The hardware can combine H&V syncs onto the output enable line
as composite syncs, so add the relevant configuration to do that.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
This reverts commit 94902ee299 which is
upstream commit ef54c1a476.
Reverting for now due to issues that need to get fixed upstream.
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 868ddfcef3 upstream.
The code for hdac_ext_stream seems inherited from hdac_stream, and
similar locking issues are present: the use of the bus->reg_lock
spinlock is inconsistent, with only writes to specific fields being
protected.
Apply similar fix as in hdac_stream by protecting all accesses to
'link_locked' and 'decoupled' fields, with a new helper
snd_hdac_ext_stream_decouple_locked() added to simplify code
changes.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210924192417.169243-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef775a0e36 upstream.
When CONFIG_PROC_FS is not set, there is a build warning (turned
into an error):
../drivers/hwmon/dell-smm-hwmon.c: In function 'i8k_init_procfs':
../drivers/hwmon/dell-smm-hwmon.c:624:24: error: unused variable 'data' [-Werror=unused-variable]
struct dell_smm_data *data = dev_get_drvdata(dev);
Make I8K depend on PROC_FS and HWMON (instead of selecting HWMON -- it
is strongly preferred to not select entire subsystems).
Build tested in all possible combinations of SENSORS_DELL_SMM, I8K, and
PROC_FS.
Fixes: 039ae58503 ("hwmon: Allow to compile dell-smm-hwmon driver without /proc/i8k")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Pali Rohár <pali@kernel.org>
Link: https://lkml.kernel.org/r/20210910071921.16777-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54fde91f52 upstream.
Christoph pointed out that I'm updating bdev->bd_inode for the device
time when we remove block devices from a btrfs file system, however this
isn't actually exposed to anything. The inode we want to update is the
one that's associated with the path to the device, usually on devtmpfs,
so that blkid notices the difference.
We still don't want to do the blkdev_open, so use kern_path() to get the
path to the given device and do the update time on that inode.
Fixes: 8f96a5bfa1 ("btrfs: update the bdev time directly when closing")
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e60feb445f upstream.
If you already have an inode and need to update the time on the inode
there is no way to do this properly. Export this helper to allow file
systems to update time on the inode so the appropriate handler is
called, either ->update_time or generic_update_time.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2ff04286a9 upstream.
PF pointer is always valid when PCI core calls its .shutdown() and
.remove() callbacks. There is no need to check it again.
Fixes: 837f08fdec ("ice: Add basic driver framework for Intel(R) E800 Series")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc153aba3e upstream.
Instead of maintaining a single-linked list of devices that must be
searched linearly in .remove() just use spi_set_drvdata() to remember the
link between the spi device and the driver struct. Then the global list
and the next member can be dropped.
This simplifies the driver, reduces the memory footprint and the time to
search the list. Also it makes obvious that there is always a corresponding
driver struct for a given device in .remove(), so the error path for
!max3421_hcd can be dropped, too.
As a side effect this fixes a data inconsistency when .probe() races with
itself for a second max3421 device in manipulating max3421_hcd_list. A
similar race is fixed in .remove(), too.
Fixes: 2d53139f31 ("Add support for using a MAX3421E chip as a host driver.")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211018204028.2914597-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 827b0913a9 upstream.
The recent fix for DAPM to correct the kctl change notification by the
commit 5af82c81b2 ("ASoC: DAPM: Fix missing kctl change
notifications") caused other regressions since it changed the behavior
of snd_soc_dapm_set_pin() that is called from several API functions.
Formerly it returned always 0 for success, but now it returns 0 or 1.
This patch addresses it, restoring the old behavior of
snd_soc_dapm_set_pin() while keeping the fix in
snd_soc_dapm_put_pin_switch().
Fixes: 5af82c81b2 ("ASoC: DAPM: Fix missing kctl change notifications")
Reported-by: Yu-Hsuan Hsu <yuhsuan@chromium.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20211105090925.20575-1-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc27f3c5d1 upstream.
When the hash table slot array allocation fails in hashtab_init(),
h->size is left initialized with a non-zero value, but the h->htable
pointer is NULL. This may then cause a NULL pointer dereference, since
the policydb code relies on the assumption that even after a failed
hashtab_init(), hashtab_map() and hashtab_destroy() can be safely called
on it. Yet, these detect an empty hashtab only by looking at the size.
Fix this by making sure that hashtab_init() always leaves behind a valid
empty hashtab when the allocation fails.
Cc: stable@vger.kernel.org
Fixes: 03414a49ad ("selinux: do not allocate hashtabs dynamically")
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4a118f2ee upstream.
When __unmap_hugepage_range() calls to huge_pmd_unshare() succeed, a TLB
flush is missing. This TLB flush must be performed before releasing the
i_mmap_rwsem, in order to prevent an unshared PMDs page from being
released and reused before the TLB flush took place.
Arguably, a comprehensive solution would use mmu_gather interface to
batch the TLB flushes and the PMDs page release, however it is not an
easy solution: (1) try_to_unmap_one() and try_to_migrate_one() also call
huge_pmd_unshare() and they cannot use the mmu_gather interface; and (2)
deferring the release of the page reference for the PMDs page until
after i_mmap_rwsem is dropeed can confuse huge_pmd_unshare() into
thinking PMDs are shared when they are not.
Fix __unmap_hugepage_range() by adding the missing TLB flush, and
forcing a flush when unshare is successful.
Fixes: 24669e5847 ("hugetlb: use mmu_gather instead of a temporary linked list for accumulating pages)" # 3.6
Signed-off-by: Nadav Amit <namit@vmware.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 886fe2915c upstream.
__ufshcd_issue_tm_cmd() clears req->end_io_data after timing out, which
races with the completion function ufshcd_tmc_handler() which expects
req->end_io_data to have a value.
Note __ufshcd_issue_tm_cmd() and ufshcd_tmc_handler() are already
synchronized using hba->tmf_rqs and hba->outstanding_tasks under the
host_lock spinlock.
It is also not necessary (nor typical) to clear req->end_io_data because
the block layer does it before allocating out requests e.g. via
blk_get_request().
So fix by not clearing it.
Link: https://lore.kernel.org/r/20211108064815.569494-2-adrian.hunter@intel.com
Fixes: f5ef336fd2 ("scsi: ufs: core: Fix task management completion")
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[Adrian: Backport to v5.10]
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f5ef336fd2 upstream.
The UFS driver uses blk_mq_tagset_busy_iter() when identifying task
management requests to complete, however blk_mq_tagset_busy_iter() doesn't
work.
blk_mq_tagset_busy_iter() only iterates requests dispatched by the block
layer. That appears as if it might have started since commit 37f4a24c24
("blk-mq: centralise related handling into blk_mq_get_driver_tag") which
removed 'data->hctx->tags->rqs[rq->tag] = rq' from blk_mq_rq_ctx_init()
which gets called:
blk_get_request
blk_mq_alloc_request
__blk_mq_alloc_request
blk_mq_rq_ctx_init
Since UFS task management requests are not dispatched by the block layer,
hctx->tags->rqs[rq->tag] remains NULL, and since blk_mq_tagset_busy_iter()
relies on finding requests using hctx->tags->rqs[rq->tag], UFS task
management requests are never found by blk_mq_tagset_busy_iter().
By using blk_mq_tagset_busy_iter(), the UFS driver was relying on internal
details of the block layer, which was fragile and subsequently got
broken. Fix by removing the use of blk_mq_tagset_busy_iter() and having the
driver keep track of task management requests.
Link: https://lore.kernel.org/r/20210922091059.4040-1-adrian.hunter@intel.com
Fixes: 1235fc569e ("scsi: ufs: core: Fix task management request completion timeout")
Fixes: 69a6c269c0 ("scsi: ufs: Use blk_{get,put}_request() to allocate and free TMFs")
Cc: stable@vger.kernel.org
Tested-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[Adrian: Backport to v5.10]
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf55208391 upstream.
amdgpu_connector_vga_get_modes missed function amdgpu_get_native_mode
which assign amdgpu_encoder->native_mode with *preferred_mode result in
amdgpu_encoder->native_mode.clock always be 0. That will cause
amdgpu_connector_set_property returned early on:
if ((rmx_type != DRM_MODE_SCALE_NONE) &&
(amdgpu_encoder->native_mode.clock == 0))
when we try to set scaling mode Full/Full aspect/Center.
Add the missing function to amdgpu_connector_vga_get_mode can fix this.
It also works on dvi connectors because
amdgpu_connector_dvi_helper_funcs.get_mode use the same method.
Signed-off-by: hongao <hongao@uniontech.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c34bd4532 upstream.
Atm, there are no sink rate values set for DP (vs. eDP) sinks until the
DPCD capabilities are successfully read from the sink. During this time
intel_dp->num_common_rates is 0 which can lead to a
intel_dp->common_rates[-1] (*)
access, which is an undefined behaviour, in the following cases:
- In intel_dp_sync_state(), if the encoder is enabled without a sink
connected to the encoder's connector (BIOS enabled a monitor, but the
user unplugged the monitor until the driver loaded).
- In intel_dp_sync_state() if the encoder is enabled with a sink
connected, but for some reason the DPCD read has failed.
- In intel_dp_compute_link_config() if modesetting a connector without
a sink connected on it.
- In intel_dp_compute_link_config() if modesetting a connector with a
a sink connected on it, but before probing the connector first.
To avoid the (*) access in all the above cases, make sure that the sink
rate table - and hence the common rate table - is always valid, by
setting a default minimum sink rate when registering the connector
before anything could use it.
I also considered setting all the DP link rates by default, so that
modesetting with higher resolution modes also succeeds in the last two
cases above. However in case a sink is not connected that would stop
working after the first modeset, due to the LT fallback logic. So this
would need more work, beyond the scope of this fix.
As I mentioned in the previous patch, I don't think the issue this patch
fixes is user visible, however it is an undefined behaviour by
definition and triggers a BUG() in CONFIG_UBSAN builds, hence CC:stable.
v2: Clear the default sink rates, before initializing these for eDP.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/4297
References: https://gitlab.freedesktop.org/drm/intel/-/issues/4298
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211018143417.1452632-1-imre.deak@intel.com
(cherry picked from commit 3f61ef9777)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f55aaf63bd upstream.
The postclose handler can run after the device has been removed (or the
driver has been unbound) since userspace clients are free to hold the
file open as long as they want. Because the device removal callback
frees the entire nouveau_drm structure, any reference to it in the
postclose handler will result in a use-after-free.
To reproduce this, one must simply open the device file, unbind the
driver (or physically remove the device), and then close the device
file. This was found and can be reproduced easily with the IGT
core_hotunplug tests.
To avoid this, all clients are cleaned up in the device finalization
rather than deferring it to the postclose handler, and the postclose
handler is protected by a critical section which ensures the
drm_dev_unplug() and the postclose handler won't race.
This is not an ideal fix, since as I understand the proposed plan for
the kernel<->userspace interface for hotplug support, destroying the
client before the file is closed will cause problems. However, I believe
to properly fix this issue, the lifetime of the nouveau_drm structure
needs to be extended to match the drm_device, and this proved to be a
rather invasive change. Thus, I've broken this out so the fix can be
easily backported.
This fixes with the two previous commits CVE-2020-27820 (Karol).
Cc: stable@vger.kernel.org # 5.4+
Signed-off-by: Jeremy Cline <jcline@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Ben Skeggs <bskeggs@redhat.com>
Tested-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201125202648.5220-4-jcline@redhat.com
Link: https://gitlab.freedesktop.org/drm/nouveau/-/merge_requests/14
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bec05f33eb upstream.
sticon_build_attr() checked the reverse argument and flipped
background and foreground color, but returned the non-reverse
value afterwards. Fix this and also add two local variables
for foreground and background color to make the code easier
to read.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45da9c1767 upstream.
Ordered work functions aren't guaranteed to be handled by the same thread
which executed the normal work functions. The only way execution between
normal/ordered functions is synchronized is via the WORK_DONE_BIT,
unfortunately the used bitops don't guarantee any ordering whatsoever.
This manifested as seemingly inexplicable crashes on ARM64, where
async_chunk::inode is seen as non-null in async_cow_submit which causes
submit_compressed_extents to be called and crash occurs because
async_chunk::inode suddenly became NULL. The call trace was similar to:
pc : submit_compressed_extents+0x38/0x3d0
lr : async_cow_submit+0x50/0xd0
sp : ffff800015d4bc20
<registers omitted for brevity>
Call trace:
submit_compressed_extents+0x38/0x3d0
async_cow_submit+0x50/0xd0
run_ordered_work+0xc8/0x280
btrfs_work_helper+0x98/0x250
process_one_work+0x1f0/0x4ac
worker_thread+0x188/0x504
kthread+0x110/0x114
ret_from_fork+0x10/0x18
Fix this by adding respective barrier calls which ensure that all
accesses preceding setting of WORK_DONE_BIT are strictly ordered before
setting the flag. At the same time add a read barrier after reading of
WORK_DONE_BIT in run_ordered_work which ensures all subsequent loads
would be strictly ordered after reading the bit. This in turn ensures
are all accesses before WORK_DONE_BIT are going to be strictly ordered
before any access that can occur in ordered_func.
Reported-by: Chris Murphy <lists@colorremedies.com>
Fixes: 08a9ff3264 ("btrfs: Added btrfs_workqueue_struct implemented ordered execution based on kernel workqueue")
CC: stable@vger.kernel.org # 4.4+
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2011928
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Tested-by: Chris Murphy <chris@colorremedies.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9119570039 upstream.
According to upstream commit 5ec55823438e("net: stmmac:
add clocks management for gmac driver"), it improve clocks
management for stmmac driver. So, it is necessary to implement
the runtime callback in dwmac-socfpga driver because it doesn't
use the common stmmac_pltfr_pm_ops instance. Otherwise, clocks
are not disabled when system enters suspend status.
Fixes: 5ec5582343 ("net: stmmac: add clocks management for gmac driver")
Cc: stable@vger.kernel.org
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a48fc69fe6 upstream.
udf_readdir() didn't validate the directory position it should start
reading from. Thus when user uses lseek(2) on directory file descriptor
it can trick udf_readdir() into reading from a position in the middle of
directory entry which then upsets directory parsing code resulting in
errors or even possible kernel crashes. Similarly when the directory is
modified between two readdir calls, the directory position need not be
valid anymore.
Add code to validate current offset in the directory. This is actually
rather expensive for UDF as we need to read from the beginning of the
directory and parse all directory entries. This is because in UDF a
directory is just a stream of data containing directory entries and
since file names are fully under user's control we cannot depend on
detecting magic numbers and checksums in the header of directory entry
as a malicious attacker could fake them. We skip this step if we detect
that nothing changed since the last readdir call.
Reported-by: Nathan Wilson <nate@chickenbrittle.com>
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af957eebfc upstream.
When loading nested state, don't use check vcpu->arch.efer to get the
L1 host's 64-bit vs. 32-bit state and don't check it for consistency
with respect to VM_EXIT_HOST_ADDR_SPACE_SIZE, as register state in vCPU
may be stale when KVM_SET_NESTED_STATE is called---and architecturally
does not exist. When restoring L2 state in KVM, the CPU is placed in
non-root where nested VMX code has no snapshot of L1 host state: VMX
(conditionally) loads host state fields loaded on VM-exit, but they need
not correspond to the state before entry. A simple case occurs in KVM
itself, where the host RIP field points to vmx_vmexit rather than the
instruction following vmlaunch/vmresume.
However, for the particular case of L1 being in 32- or 64-bit mode
on entry, the exit controls can be treated instead as the source of
truth regarding the state of L1 on entry, and can be used to check
that vmcs12.VM_EXIT_HOST_ADDR_SPACE_SIZE matches vmcs12.HOST_EFER if
vmcs12.VM_EXIT_LOAD_IA32_EFER is set. The consistency check on CPU
EFER vs. vmcs12.VM_EXIT_HOST_ADDR_SPACE_SIZE, instead, happens only
on VM-Enter. That's because, again, there's conceptually no "current"
L1 EFER to check on KVM_SET_NESTED_STATE.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20211115131837.195527-2-mlevitsk@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e35eba405 upstream.
As spotted and explained in commit c12ab8dbc4 ("powerpc/8xx: Fix
Oops with STRICT_KERNEL_RWX without DEBUG_RODATA_TEST"), the selection
of STRICT_KERNEL_RWX without selecting DEBUG_RODATA_TEST has spotted
the lack of the DIRTY bit in the pinned kernel data TLBs.
This problem should have been detected a lot earlier if things had
been working as expected. But due to an incredible level of chance or
mishap, this went undetected because of a set of bugs: In fact the
DTLBs were not pinned, because instead of setting the reserve bit
in MD_CTR, it was set in MI_CTR that is the register for ITLBs.
But then, another huge bug was there: the physical address was
reset to 0 at the boundary between RO and RW areas, leading to the
same physical space being mapped at both 0xc0000000 and 0xc8000000.
This had by miracle no consequence until now because the entry was
not really pinned so it was overwritten soon enough to go undetected.
Of course, now that we really pin the DTLBs, it must be fixed as well.
Fixes: f76c8f6d25 ("powerpc/8xx: Add function to set pinned TLBs")
Cc: stable@vger.kernel.org # v5.8+
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Depends-on: c12ab8dbc4 ("powerpc/8xx: Fix Oops with STRICT_KERNEL_RWX without DEBUG_RODATA_TEST")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/a21e9a057fe2d247a535aff0d157a54eefee017a.1636963688.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 126e8bee94 upstream.
Patch series "shm: shm_rmid_forced feature fixes".
Some time ago I met kernel crash after CRIU restore procedure,
fortunately, it was CRIU restore, so, I had dump files and could do
restore many times and crash reproduced easily. After some
investigation I've constructed the minimal reproducer. It was found
that it's use-after-free and it happens only if sysctl
kernel.shm_rmid_forced = 1.
The key of the problem is that the exit_shm() function not handles shp's
object destroy when task->sysvshm.shm_clist contains items from
different IPC namespaces. In most cases this list will contain only
items from one IPC namespace.
How can this list contain object from different namespaces? The
exit_shm() function is designed to clean up this list always when
process leaves IPC namespace. But we made a mistake a long time ago and
did not add a exit_shm() call into the setns() syscall procedures.
The first idea was just to add this call to setns() syscall but it
obviously changes semantics of setns() syscall and that's
userspace-visible change. So, I gave up on this idea.
The first real attempt to address the issue was just to omit forced
destroy if we meet shp object not from current task IPC namespace [1].
But that was not the best idea because task->sysvshm.shm_clist was
protected by rwsem which belongs to current task IPC namespace. It
means that list corruption may occur.
Second approach is just extend exit_shm() to properly handle shp's from
different IPC namespaces [2]. This is really non-trivial thing, I've
put a lot of effort into that but not believed that it's possible to
make it fully safe, clean and clear.
Thanks to the efforts of Manfred Spraul working an elegant solution was
designed. Thanks a lot, Manfred!
Eric also suggested the way to address the issue in ("[RFC][PATCH] shm:
In shm_exit destroy all created and never attached segments") Eric's
idea was to maintain a list of shm_clists one per IPC namespace, use
lock-less lists. But there is some extra memory consumption-related
concerns.
An alternative solution which was suggested by me was implemented in
("shm: reset shm_clist on setns but omit forced shm destroy"). The idea
is pretty simple, we add exit_shm() syscall to setns() but DO NOT
destroy shm segments even if sysctl kernel.shm_rmid_forced = 1, we just
clean up the task->sysvshm.shm_clist list.
This chages semantics of setns() syscall a little bit but in comparision
to the "naive" solution when we just add exit_shm() without any special
exclusions this looks like a safer option.
[1] https://lkml.org/lkml/2021/7/6/1108
[2] https://lkml.org/lkml/2021/7/14/736
This patch (of 2):
Let's produce a warning if we trying to remove non-existing IPC object
from IPC namespace kht/idr structures.
This allows us to catch possible bugs when the ipc_rmid() function was
called with inconsistent struct ipc_ids*, struct kern_ipc_perm*
arguments.
Link: https://lkml.kernel.org/r/20211027224348.611025-1-alexander.mikhalitsyn@virtuozzo.com
Link: https://lkml.kernel.org/r/20211027224348.611025-2-alexander.mikhalitsyn@virtuozzo.com
Co-developed-by: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Alexander Mikhalitsyn <alexander.mikhalitsyn@virtuozzo.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Andrei Vagin <avagin@gmail.com>
Cc: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Cc: Vasily Averin <vvs@virtuozzo.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51f2ec5934 upstream.
When building allmodconfig, there is a warning about TIMER_ENABLE being
redefined:
drivers/clocksource/timer-oxnas-rps.c:39:9: error: 'TIMER_ENABLE' macro redefined [-Werror,-Wmacro-redefined]
#define TIMER_ENABLE BIT(7)
^
arch/hexagon/include/asm/timer-regs.h:13:9: note: previous definition is here
#define TIMER_ENABLE 0
^
1 error generated.
The values in this header are only used in one file each, if they are
used at all. Remove the header and sink all of the constants into their
respective files.
TCX0_CLK_RATE is only used in arch/hexagon/include/asm/timex.h
TIMER_ENABLE, RTOS_TIMER_INT, RTOS_TIMER_REGS_ADDR are only used in
arch/hexagon/kernel/time.c.
SLEEP_CLK_RATE and TIMER_CLR_ON_MATCH have both been unused since the
file's introduction in commit 71e4a47f32 ("Hexagon: Add time and timer
functions").
TIMER_ENABLE is redefined as BIT(0) so the shift is moved into the
definition, rather than its use.
Link: https://lkml.kernel.org/r/20211115174250.1994179-3-nathan@kernel.org
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Brian Cain <bcain@codeaurora.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ffb92ce826 upstream.
Patch series "Fixes for ARCH=hexagon allmodconfig", v2.
This series fixes some issues noticed with ARCH=hexagon allmodconfig.
This patch (of 3):
When building ARCH=hexagon allmodconfig, the following errors occur:
ERROR: modpost: "__raw_readsl" [drivers/i3c/master/svc-i3c-master.ko] undefined!
ERROR: modpost: "__raw_writesl" [drivers/i3c/master/dw-i3c-master.ko] undefined!
ERROR: modpost: "__raw_readsl" [drivers/i3c/master/dw-i3c-master.ko] undefined!
ERROR: modpost: "__raw_writesl" [drivers/i3c/master/i3c-master-cdns.ko] undefined!
ERROR: modpost: "__raw_readsl" [drivers/i3c/master/i3c-master-cdns.ko] undefined!
Export these symbols so that modules can use them without any errors.
Link: https://lkml.kernel.org/r/20211115174250.1994179-1-nathan@kernel.org
Link: https://lkml.kernel.org/r/20211115174250.1994179-2-nathan@kernel.org
Fixes: 013bf24c38 ("Hexagon: Provide basic implementation and/or stubs for I/O routines.")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Brian Cain <bcain@codeaurora.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14831fad73 upstream.
When running the following command without arm-linux-gnueabi-gcc in
one's $PATH, the following warning is observed:
$ ARCH=arm64 CROSS_COMPILE_COMPAT=arm-linux-gnueabi- make -j72 LLVM=1 mrproper
make[1]: arm-linux-gnueabi-gcc: No such file or directory
This is because KCONFIG is not run for mrproper, so CONFIG_CC_IS_CLANG
is not set, and we end up eagerly evaluating various variables that try
to invoke CC_COMPAT.
This is a similar problem to what was observed in
commit dc960bfeed ("h8300: suppress error messages for 'make clean'")
Reported-by: Lucas Henneman <henneman@google.com>
Suggested-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20211019223646.1146945-4-ndesaulniers@google.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aec3f415f7 upstream.
Commit 2d26f6e39a ("net: stmmac: dwmac-rk: fix unbalanced pm_runtime_enable warnings")
while getting rid of a runtime PM warning ended up breaking ethernet
on rk3399 based devices. By dropping an extra reference to the device,
the commit ends up enabling suspend / resume of the ethernet device -
which appears to be broken.
While the issue with runtime pm is being investigated, partially
revert commit 2d26f6e39a to restore the network on rk3399.
Fixes: 2d26f6e39a ("net: stmmac: dwmac-rk: fix unbalanced pm_runtime_enable warnings")
Suggested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Punit Agrawal <punitagrawal@gmail.com>
Cc: Michael Riesch <michael.riesch@wolfvision.net>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20210929135049.3426058-1-punitagrawal@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 20c76e242e ]
kexec_file_add_ipl_report ignores that ipl_report_finish may fail and
can return an error pointer instead of a valid pointer.
Fix this and simplify by returning NULL in case of an error and let
the only caller handle this case.
Fixes: 99feaa717e ("s390/kexec_file: Create ipl report and pass to next kernel")
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a3a100473 ]
It has been observed that dual edge triggered wakeirq GPIOs on SDM845
doesn't trigger interrupts on the falling edge.
Enabling wakeirq_dual_edge_errata for SDM845 indicates that the PDC in
SDM845 suffers from the same problem described, and worked around, by
Doug in 'c3c0c2e18d94 ("pinctrl: qcom: Handle broken/missing PDC dual
edge IRQs on sc7180")', so enable the workaround for SDM845 as well.
The specific problem seen without this is that gpio-keys does not detect
the falling edge of the LID gpio on the Lenovo Yoga C630 and as such
consistently reports the LID as closed.
Fixes: e35a6ae0eb ("pinctrl/msm: Setup GPIO chip in hierarchy")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-By: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20211102034115.1946036-1-bjorn.andersson@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dae5818646 ]
kvmppc_h_set_dabr(), and kvmppc_h_set_xdabr() which jumps into
it, need to use _GLOBAL_TOC to setup the kernel TOC pointer, because
kvmppc_h_set_dabr() uses LOAD_REG_ADDR() to load dawr_force_enable.
When called from hcall_try_real_mode() we have the kernel TOC in r2,
established near the start of kvmppc_interrupt_hv(), so there is no
issue.
But they can also be called from kvmppc_pseries_do_hcall() which is
module code, so the access ends up happening with the kvm-hv module's
r2, which will not point at dawr_force_enable and could even cause a
fault.
With the current code layout and compilers we haven't observed a fault
in practice, the load hits somewhere in kvm-hv.ko and silently returns
some bogus value.
Note that we we expect p8/p9 guests to use the DAWR, but SLOF uses
h_set_dabr() to test if sc1 works correctly, see SLOF's
lib/libhvcall/brokensc1.c.
Fixes: c1fe190c06 ("powerpc: Add force enable of DAWR on P9 option")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Link: https://lore.kernel.org/r/20210923151031.72408-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d2ca2e12d ]
As reported in [1], e100 was no longer working for suspend/resume
cycles. The previous commit mentioned in the fixes appears to have
broken things and this attempts to practice best known methods for
device power management and keep wake-up working while allowing
suspend/resume to work. To do this, I reorder a little bit of code
and fix the resume path to make sure the device is enabled.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=214933
Fixes: 69a74aef8a ("e100: use generic power management")
Cc: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Reported-by: Alexey Kuznetsov <axet@me.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Alexey Kuznetsov <axet@me.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48b71a9e66 ]
There are two sites that calls queue_work() after the
destroy_workqueue() and lead to possible UAF.
The first site is nci_send_cmd(), which can happen after the
nci_close_device as below
nfcmrvl_nci_unregister_dev | nfc_genl_dev_up
nci_close_device |
flush_workqueue |
del_timer_sync |
nci_unregister_device | nfc_get_device
destroy_workqueue | nfc_dev_up
nfc_unregister_device | nci_dev_up
device_del | nci_open_device
| __nci_request
| nci_send_cmd
| queue_work !!!
Another site is nci_cmd_timer, awaked by the nci_cmd_work from the
nci_send_cmd.
... | ...
nci_unregister_device | queue_work
destroy_workqueue |
nfc_unregister_device | ...
device_del | nci_cmd_work
| mod_timer
| ...
| nci_cmd_timer
| queue_work !!!
For the above two UAF, the root cause is that the nfc_dev_up can race
between the nci_unregister_device routine. Therefore, this patch
introduce NCI_UNREG flag to easily eliminate the possible race. In
addition, the mutex_lock in nci_close_device can act as a barrier.
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Fixes: 6a2968aaf5 ("NFC: basic NCI protocol implementation")
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211116152732.19238-1-linma@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f011539e72 ]
If there is a NCI command in work queue after closing the NCI device at
nci_unregister_device, The NCI command timer starts at flush_workqueue
function and then NCI command timeout handler would be called 5 second
after flushing the NCI command work queue and destroying the queue.
At that time, the timeout handler would try to use NCI command work queue
that is destroyed already. it will causes the problem. To avoid this
abnormal situation, change the sequence to prevent the NCI command timeout
handler from being called after destroying the NCI command work queue.
Signed-off-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e3b5dfcd1 ]
There is a potential UAF between the unregistration routine and the NFC
netlink operations.
The race that cause that UAF can be shown as below:
(FREE) | (USE)
nfcmrvl_nci_unregister_dev | nfc_genl_dev_up
nci_close_device |
nci_unregister_device | nfc_get_device
nfc_unregister_device | nfc_dev_up
rfkill_destory |
device_del | rfkill_blocked
... | ...
The root cause for this race is concluded below:
1. The rfkill_blocked (USE) in nfc_dev_up is supposed to be placed after
the device_is_registered check.
2. Since the netlink operations are possible just after the device_add
in nfc_register_device, the nfc_dev_up() can happen anywhere during the
rfkill creation process, which leads to data race.
This patch reorder these actions to permit
1. Once device_del is finished, the nfc_dev_up cannot dereference the
rfkill object.
2. The rfkill_register need to be placed after the device_add of nfc_dev
because the parent device need to be created first. So this patch keeps
the order but inject device_lock to prevent the data race.
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Fixes: be055b2f89 ("NFC: RFKILL support")
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211116152652.19217-1-linma@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86cdf8e387 ]
There is a possible data race as shown below:
thread-A in nci_request() | thread-B in nci_close_device()
| mutex_lock(&ndev->req_lock);
test_bit(NCI_UP, &ndev->flags); |
... | test_and_clear_bit(NCI_UP, &ndev->flags)
mutex_lock(&ndev->req_lock); |
|
This race will allow __nci_request() to be awaked while the device is
getting removed.
Similar to commit e2cb6b891a ("bluetooth: eliminate the potential race
condition when removing the HCI controller"). this patch alters the
function sequence in nci_request() to prevent the data races between the
nci_close_device().
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Fixes: 6a2968aaf5 ("NFC: basic NCI protocol implementation")
Link: https://lore.kernel.org/r/20211115145600.8320-1-linma@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5aff430d4e ]
Fix misleading display error in dmesg if tc filter return fail.
Only i40e status error code should be converted to string, not linux
error code. Otherwise, we return false information about the error.
Fixes: 2f4b411a3d ("i40e: Enable cloud filters via tc-flower")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e6d218c1e ]
Reject TCs creation with proper message if the first queue
assignment is not equal to the power of two.
The first queue number was checked too late in the second queue
iteration, if second queue was configured at all. Now if first queue value
is not a power of two, then trying to create qdisc will be rejected.
Fixes: 8f88b3034d ("i40e: Add infrastructure for queue channel support")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a3b311e38 ]
Restore part of reset functionality used when reset is called
from the VF to reset itself. Without this fix warning message
is displayed when VF is being removed via sysfs.
Fix the crash of the VF during reset by ensuring
that the PF receives the reset message successfully.
Refactor code to use one function instead of two.
Fixes: 5c3c48ac6b ("i40e: implement virtual device interface")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e0a603cb7 ]
Properly reconfigure VF VSIs after VF request ADQ.
Created new function to update queue mapping and queue pairs per TC
with AQ update VSI. This sets proper RSS size on NIC.
VFs num_queue_pairs should not be changed during setup of queue maps.
Previously, VF main VSI in ADQ had configured too many queues and had
wrong RSS size, which lead to packets not being consumed and drops in
connectivity.
Fixes: bc6d33c8d9 ("i40e: Fix the number of queues available to be mapped for use")
Co-developed-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Eryk Rybak <eryk.roch.rybak@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d2a69fefd7 ]
Currently, the i40e_vsi_setup_queue_map is basing the count of queues in
TCs on a VSI's alloc_queue_pairs member which is not changed throughout
any user's action (for example via ethtool's set_channels callback).
This implies that vsi->tc_config.tc_info[n].qcount value that is given
to the kernel via netdev_set_tc_queue() that notifies about the count of
queues per particular traffic class is constant even if user has changed
the total count of queues.
This in turn caused the kernel warning after setting the queue count to
the lower value than the initial one:
$ ethtool -l ens801f0
Channel parameters for ens801f0:
Pre-set maximums:
RX: 0
TX: 0
Other: 1
Combined: 64
Current hardware settings:
RX: 0
TX: 0
Other: 1
Combined: 64
$ ethtool -L ens801f0 combined 40
[dmesg]
Number of in use tx queues changed invalidating tc mappings. Priority
traffic classification disabled!
Reason was that vsi->alloc_queue_pairs stayed at 64 value which was used
to set the qcount on TC0 (by default only TC0 exists so all of the
existing queues are assigned to TC0). we update the offset/qcount via
netdev_set_tc_queue() back to the old value but then the
netif_set_real_num_tx_queues() is using the vsi->num_queue_pairs as a
value which got set to 40.
Fix it by using vsi->req_queue_pairs as a queue count that will be
distributed across TCs. Do it only for non-zero values, which implies
that user actually requested the new count of queues.
For VSIs other than main, stay with the vsi->alloc_queue_pairs as we
only allow manipulating the queue count on main VSI.
Fixes: bc6d33c8d9 ("i40e: Fix the number of queues available to be mapped for use")
Co-developed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Co-developed-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Eryk Rybak <eryk.roch.rybak@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf9acc90c8 ]
virtio_net_hdr_to_skb does not set the skb's gso_size and gso_type
correctly for UFO packets received via virtio-net that are a little over
the GSO size. This can lead to problems elsewhere in the networking
stack, e.g. ovs_vport_send dropping over-sized packets if gso_size is
not set.
This is due to the comparison
if (skb->len - p_off > gso_size)
not properly accounting for the transport layer header.
p_off includes the size of the transport layer header (thlen), so
skb->len - p_off is the size of the TCP/UDP payload.
gso_size is read from the virtio-net header. For UFO, fragmentation
happens at the IP level so does not need to include the UDP header.
Hence the calculation could be comparing a TCP/UDP payload length with
an IP payload length, causing legitimate virtio-net packets to have
lack gso_type/gso_size information.
Example: a UDP packet with payload size 1473 has IP payload size 1481.
If the guest used UFO, it is not fragmented and the virtio-net header's
flags indicate that it is a GSO frame (VIRTIO_NET_HDR_GSO_UDP), with
gso_size = 1480 for an MTU of 1500. skb->len will be 1515 and p_off
will be 42, so skb->len - p_off = 1473. Hence the comparison fails, and
shinfo->gso_size and gso_type are not set as they should be.
Instead, add the UDP header length before comparing to gso_size when
using UFO. In this way, it is the size of the IP payload that is
compared to gso_size.
Fixes: 6dd912f826 ("net: check untrusted gso_size at kernel entry")
Signed-off-by: Jonathan Davies <jonathan.davies@nutanix.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b5a333272 ]
Access to netdev after free_netdev() will cause use-after-free bug.
Move debug log before free_netdev() call to avoid it.
Fixes: 7472dd9f64 ("staging: fsl-dpaa2/eth: Move print message")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f799ada6bf ]
Without dropping dst, the packets sent from local mirred/redirected
to ingress will may still use the old dst. ip_rcv() will drop it as
the old dst is for output and its .input is dst_discard.
This patch is to fix by also dropping dst for those packets that are
mirred or redirected from egress to ingress in act_mirred.
Note that we don't drop it for the direction change from ingress to
egress, as on which there might be a user case attaching a metadata
dst by act_tunnel_key that would be used later.
Fixes: b57dc7c13e ("net/sched: Introduce action ct")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Cong Wang <cong.wang@bytedance.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4edd8cd4e8 ]
This fixes a regression added with:
commit f0f82e2476 ("scsi: core: Fix capacity set to zero after
offlinining device")
The problem is that after iSCSI recovery, iscsid will call into the kernel
to set the dev's state to running, and with that patch we now call
scsi_rescan_device() with the state_mutex held. If the SCSI error handler
thread is just starting to test the device in scsi_send_eh_cmnd() then it's
going to try to grab the state_mutex.
We are then stuck, because when scsi_rescan_device() tries to send its I/O
scsi_queue_rq() calls -> scsi_host_queue_ready() -> scsi_host_in_recovery()
which will return true (the host state is still in recovery) and I/O will
just be requeued. scsi_send_eh_cmnd() will then never be able to grab the
state_mutex to finish error handling.
To prevent the deadlock move the rescan-related code to after we drop the
state_mutex.
This also adds a check for if we are already in the running state. This
prevents extra scans and helps the iscsid case where if the transport class
has already onlined the device during its recovery process then we don't
need userspace to do it again plus possibly block that daemon.
Link: https://lore.kernel.org/r/20211105221048.6541-3-michael.christie@oracle.com
Fixes: f0f82e2476 ("scsi: core: Fix capacity set to zero after offlinining device")
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: lijinlin <lijinlin3@huawei.com>
Cc: Wu Bo <wubo40@huawei.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Wu Bo <wubo40@huawei.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4c3176739 ]
On regular ConnectX HCAs getting encap mode isn't supported when the
E-Switch is in NONE mode. Current code would return no error code when
trying to get encap mode in such case which is wrong.
Fix by returning error value to indicate failure to caller in such case.
Fixes: 8e0aa4bc95 ("net/mlx5: E-switch, Protect eswitch mode changes")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c55479d0cb ]
E-Switch mode change routine will take the write lock to prevent any
consumer to access the E-Switch resources while E-Switch is going
through a mode change.
In the next patch
E-Switch consumers (e.g vport representors) will take read_lock prior to
accessing E-Switch resources to prevent E-Switch mode changing in the
middle of the operation.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae396d85c0 ]
Currently, In NETDEV_CHANGELOWERSTATE/NETDEV_CHANGEUPPERSTATE events
handling, tracking is not fully completed if the LAG device is not ready
at the time the events occur. But, we must keep track of the upper and
lower states after receiving the events because RoCE needs this info in
mlx5_lag_get_roce_netdev() - in order to return the corresponding port
that its running on. Returning the wrong (not most recent) port will lead
to gids table being incorrect.
For example: If during the attachment of a slave to the bond, the other
non-attached port performs pci_reload, then the LAG device is not ready,
but that should not result in dismissing attached slave tracker update
automatically (which is performed in mlx5_handle_changelowerstate()), Since
these events might not come later, which can lead to both bond ports
having tx_enabled=0 - which is not a valid state of LAG bond.
Fixes: 9b412cc35f ("net/mlx5e: Add LAG warning if bond slave is not lag master")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 255e51da15 ]
In the case where fw_getenv returns an error when fetching values
for ememsizea and memsize then variable phys_memsize is not assigned
a variable and will be uninitialized on a zero check of phys_memsize.
Fix this by initializing phys_memsize to zero.
Cleans up cppcheck error:
arch/mips/generic/yamon-dt.c:100:7: error: Uninitialized variable: phys_memsize [uninitvar]
Fixes: f41d2430bb ("MIPS: generic/yamon-dt: Support > 256MB of RAM")
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a6e9e483a ]
Now setting combine to 0 will be rejected with the
appropriate error code.
This has been implemented by adding a condition that checks
the value of combine equal to zero.
Without this patch, when the user requested it, no error was
returned and combine was set to the default value for VF.
Fixes: 5520deb153 ("iavf: Enable support for up to 16 queues")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 321421b57a ]
While issuing VF Reset from the guest OS, the VF driver prints
logs about critical / Overflow error detection. This is not an
actual error since the VF_MBX_ARQLEN register is set to all FF's
for a short period of time and the VF would catch the bits set if
it was reading the register during that spike of time.
This patch introduces an additional check to ignore this condition
since the VF is in reset.
Fixes: 19b73d8efa ("i40evf: Add additional check for reset")
Signed-off-by: Surabhi Boob <surabhi.boob@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 131b0edc40 ]
In some cases, the ethtool get_rxfh handler may be called with a null
key or indir parameter. So check these pointers, or you will have a very
bad day.
Fixes: 43a3d9ba34 ("i40evf: Allow PF driver to configure RSS")
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f04008038 ]
In iavf_config_clsflower, the filter structure could be accidentally
released at the end, if iavf_parse_cls_flower or iavf_handle_tclass ever
return a non-zero but positive value.
In this case, the function continues through to the end, and will call
kfree() on the filter structure even though it has been added to the
linked list.
This can actually happen because iavf_parse_cls_flower will return
a positive IAVF_ERR_CONFIG value instead of the traditional negative
error codes.
Fix this by ensuring that the kfree() check and error checks are
similar. Use the more idiomatic "if (err)" to catch all non-zero error
codes.
Fixes: 0075fa0fad ("i40evf: Add support to apply cloud filters")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8905072a19 ]
The driver could only quit allmulti when allmulti and promisc modes are
turn on at the same time. If promisc had been off there was no way to turn
off allmulti mode.
The patch corrects this behavior. Switching allmulti does not depends on
promisc state mode anymore
Fixes: f42a5c74da ("i40e: Add allmulti support for the VF")
Signed-off-by: Piotr Marczak <piotr.marczak@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89f22f1296 ]
iavf_free_queues() clears adapter->num_active_queues, which
iavf_free_q_vectors() relies on, so swap the order of these two function
calls in iavf_disable_vf(). This resolves a panic encountered when the
interface is disabled and then later brought up again after PF
communication is restored.
Fixes: 65c7006f23 ("i40evf: assign num_active_queues inside i40evf_alloc_queues")
Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a4a126f4b ]
If the driver has lost contact with the PF then it enters a disabled state
and frees adapter->vf_res. However, ndo_fix_features can still be called on
the interface, so we need to check for this condition first. Since we have
no information on the features at this time simply leave them unmodified
and return.
Fixes: c4445aedfe ("i40evf: Fix VLAN features")
Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e5e6b5d9d ]
Fixed return correct code from set the new channel count.
Implemented by check if reset is done in appropriate time.
This solution give a extra time to pf for reset vf in case
when user want set new channel count for all vfs.
Without this patch it is possible to return misleading output
code to user and vf reset not to be correctly performed by pf.
Fixes: 5520deb153 ("iavf: Enable support for up to 16 queues")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 938cca9e41 ]
sk_clone_lock() needs to call sock_inuse_add(1) before entering the
sk_free_unlock_clone() error path, for __sk_free() from sk_free() from
sk_free_unlock_clone() calls sock_inuse_add(-1).
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes: 648845ab7e ("sock: Move the socket inuse to namespace.")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 271351d255 ]
The MSG_CRYPTO msgs are always encrypted and sent to other nodes
for keys' deployment. But when receiving in peers, if those nodes
do not validate it and make sure it's encrypted, one could craft
a malicious MSG_CRYPTO msg to deploy its key with no need to know
other nodes' keys.
This patch is to do that by checking TIPC_SKB_CB(skb)->decrypted
and discard it if this packet never got decrypted.
Note that this is also a supplementary fix to CVE-2021-43267 that
can be triggered by an unencrypted malicious MSG_CRYPTO msg.
Fixes: 1ef6f7c939 ("tipc: add automatic session key exchange")
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0757491a1 ]
The driver does not check if hw-tc-offload is enabled for the device
before offloading a flow in the context of indirect block callback.
Fix this by checking NETIF_F_HW_TC in the features flag and rejecting
the offload request. This will avoid unnecessary dmesg error logs when
hw-tc-offload is disabled, such as these:
bnxt_en 0000:19:00.1 eno2np1: dev(ifindex=294) not on same switch
bnxt_en 0000:19:00.1 eno2np1: Error: bnxt_tc_add_flow: cookie=0xffff8dace1c88000 error=-22
bnxt_en 0000:19:00.0 eno1np0: dev(ifindex=294) not on same switch
bnxt_en 0000:19:00.0 eno1np0: Error: bnxt_tc_add_flow: cookie=0xffff8dace1c88000 error=-22
Reported-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Fixes: 627c89d00f ("bnxt_en: flow_offload: offload tunnel decap rules via indirect callbacks")
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8885ac89c ]
Smatch says:
bnx2x_init_ops.h:640 bnx2x_ilt_client_mem_op()
warn: variable dereferenced before check 'ilt' (see line 638)
Move ilt_cli variable initialization _after_ ilt validation, because
it's unsafe to deref the pointer before validation check.
Fixes: 523224a3b3 ("bnx2x, cnic, bnx2i: use new FW/HSI")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 816316caca ]
The head-of-line blocking timer should only be modified when
head-of-line drop is disabled.
One of the steps in recovering from a modem crash is to enable
dropping of packets with timeout of 0 (immediate). We don't know
how the modem configured its endpoints, so before we program the
timer, we need to ensure HOL_BLOCK is disabled.
Fixes: 84f9bd12d4 ("soc: qcom: ipa: IPA endpoints")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 70701b83e2 ]
TCP Receive zerocopy iterates through the SKB queue via
tcp_recv_skb(), acquiring a pointer to an SKB and an offset within
that SKB to read from. From there, it iterates the SKB frags array to
determine which offset to start remapping pages from.
However, this is built on the assumption that the offset read so far
within the SKB is smaller than the SKB length. If this assumption is
violated, we can attempt to read an invalid frags array element, which
would cause a fault.
tcp_recv_skb() can cause such an SKB to be returned when the TCP FIN
flag is set. Therefore, we must guard against this occurrence inside
skb_advance_frag().
One way that we can reproduce this error follows:
1) In a receiver program, call getsockopt(TCP_ZEROCOPY_RECEIVE) with:
char some_array[32 * 1024];
struct tcp_zerocopy_receive zc = {
.copybuf_address = (__u64) &some_array[0],
.copybuf_len = 32 * 1024,
};
2) In a sender program, after a TCP handshake, send the following
sequence of packets:
i) Seq = [X, X+4000]
ii) Seq = [X+4000, X+5000]
iii) Seq = [X+4000, X+5000], Flags = FIN | URG, urgptr=1000
(This can happen without URG, if we have a signal pending, but URG is
a convenient way to reproduce the behaviour).
In this case, the following event sequence will occur on the receiver:
tcp_zerocopy_receive():
-> receive_fallback_to_copy() // copybuf_len >= inq
-> tcp_recvmsg_locked() // reads 5000 bytes, then breaks due to URG
-> tcp_recv_skb() // yields skb with skb->len == offset
-> tcp_zerocopy_set_hint_for_skb()
-> skb_advance_to_frag() // will returns a frags ptr. >= nr_frags
-> find_next_mappable_frag() // will dereference this bad frags ptr.
With this patch, skb_advance_to_frag() will no longer return an
invalid frags pointer, and will return NULL instead, fixing the issue.
Signed-off-by: Arjun Roy <arjunroy@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 05255b823a ("tcp: add TCP_ZEROCOPY_RECEIVE support for zerocopy receive")
Link: https://lore.kernel.org/r/20211111235215.2605384-1-arjunroy.kdev@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7fba5309ef ]
Refactor skb frag fast-forwarding for tcp receive zerocopy. This is
part of a patch set that introduces short-circuited hybrid copies
for small receive operations, which results in roughly 33% fewer
syscalls for small RPC scenarios.
skb_advance_to_frag(), given a skb and an offset into the skb,
iterates from the first frag for the skb until we're at the frag
specified by the offset. Assuming the offset provided refers to how
many bytes in the skb are already read, the returned frag points to
the next frag we may read from, while offset_frag is set to the number
of bytes from this frag that we have already read.
If frag is not null and offset_frag is equal to 0, then we may be able
to map this frag's page into the process address space with
vm_insert_page(). However, if offset_frag is not equal to 0, then we
cannot do so.
Signed-off-by: Arjun Roy <arjunroy@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 18fb76ed53 ]
When TCP receive zerocopy does not successfully map the entire
requested space, it outputs a 'hint' that the caller should recvmsg().
Augment zerocopy to accept a user buffer that it tries to copy this
hint into - if it is possible to copy the entire hint, it will do so.
This elides a recvmsg() call for received traffic that isn't exactly
page-aligned in size.
This was tested with RPC-style traffic of arbitrary sizes. Normally,
each received message required at least one getsockopt() call, and one
recvmsg() call for the remaining unaligned data.
With this change, almost all of the recvmsg() calls are eliminated,
leading to a savings of about 25%-50% in number of system calls
for RPC-style workloads.
Signed-off-by: Arjun Roy <arjunroy@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63f84ae6b8 ]
Do not copy the fixed-size char array field of the events over
the field size. The histogram treats char array as a string and
there are 2 types of char array in the event, fixed-size and
dynamic string. The dynamic string (__data_loc) field must be
null terminated, but the fixed-size char array field may not
be null terminated (not a string, but just a data).
In that case, histogram can copy the data after the field.
This uses the original field size for fixed-size char array
field to restrict the histogram not to access over the original
field size.
Link: https://lkml.kernel.org/r/163673292822.195747.3696966210526410250.stgit@devnote2
Fixes: 02205a6752 (tracing: Add support for 'field variables')
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b781d8db58 ]
KASAN reports a use-after-free report when doing block test:
==================================================================
[10050.967049] BUG: KASAN: use-after-free in
submit_bio_checks+0x1539/0x1550
[10050.977638] Call Trace:
[10050.978190] dump_stack+0x9b/0xce
[10050.979674] print_address_description.constprop.6+0x3e/0x60
[10050.983510] kasan_report.cold.9+0x22/0x3a
[10050.986089] submit_bio_checks+0x1539/0x1550
[10050.989576] submit_bio_noacct+0x83/0xc80
[10050.993714] submit_bio+0xa7/0x330
[10050.994435] mpage_readahead+0x380/0x500
[10050.998009] read_pages+0x1c1/0xbf0
[10051.002057] page_cache_ra_unbounded+0x4c2/0x6f0
[10051.007413] do_page_cache_ra+0xda/0x110
[10051.008207] force_page_cache_ra+0x23d/0x3d0
[10051.009087] page_cache_sync_ra+0xca/0x300
[10051.009970] generic_file_buffered_read+0xbea/0x2130
[10051.012685] generic_file_read_iter+0x315/0x490
[10051.014472] blkdev_read_iter+0x113/0x1b0
[10051.015300] aio_read+0x2ad/0x450
[10051.023786] io_submit_one+0xc8e/0x1d60
[10051.029855] __se_sys_io_submit+0x125/0x350
[10051.033442] do_syscall_64+0x2d/0x40
[10051.034156] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[10051.048733] Allocated by task 18598:
[10051.049482] kasan_save_stack+0x19/0x40
[10051.050263] __kasan_kmalloc.constprop.1+0xc1/0xd0
[10051.051230] kmem_cache_alloc+0x146/0x440
[10051.052060] mempool_alloc+0x125/0x2f0
[10051.052818] bio_alloc_bioset+0x353/0x590
[10051.053658] mpage_alloc+0x3b/0x240
[10051.054382] do_mpage_readpage+0xddf/0x1ef0
[10051.055250] mpage_readahead+0x264/0x500
[10051.056060] read_pages+0x1c1/0xbf0
[10051.056758] page_cache_ra_unbounded+0x4c2/0x6f0
[10051.057702] do_page_cache_ra+0xda/0x110
[10051.058511] force_page_cache_ra+0x23d/0x3d0
[10051.059373] page_cache_sync_ra+0xca/0x300
[10051.060198] generic_file_buffered_read+0xbea/0x2130
[10051.061195] generic_file_read_iter+0x315/0x490
[10051.062189] blkdev_read_iter+0x113/0x1b0
[10051.063015] aio_read+0x2ad/0x450
[10051.063686] io_submit_one+0xc8e/0x1d60
[10051.064467] __se_sys_io_submit+0x125/0x350
[10051.065318] do_syscall_64+0x2d/0x40
[10051.066082] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[10051.067455] Freed by task 13307:
[10051.068136] kasan_save_stack+0x19/0x40
[10051.068931] kasan_set_track+0x1c/0x30
[10051.069726] kasan_set_free_info+0x1b/0x30
[10051.070621] __kasan_slab_free+0x111/0x160
[10051.071480] kmem_cache_free+0x94/0x460
[10051.072256] mempool_free+0xd6/0x320
[10051.072985] bio_free+0xe0/0x130
[10051.073630] bio_put+0xab/0xe0
[10051.074252] bio_endio+0x3a6/0x5d0
[10051.074984] blk_update_request+0x590/0x1370
[10051.075870] scsi_end_request+0x7d/0x400
[10051.076667] scsi_io_completion+0x1aa/0xe50
[10051.077503] scsi_softirq_done+0x11b/0x240
[10051.078344] blk_mq_complete_request+0xd4/0x120
[10051.079275] scsi_mq_done+0xf0/0x200
[10051.080036] virtscsi_vq_done+0xbc/0x150
[10051.080850] vring_interrupt+0x179/0x390
[10051.081650] __handle_irq_event_percpu+0xf7/0x490
[10051.082626] handle_irq_event_percpu+0x7b/0x160
[10051.083527] handle_irq_event+0xcc/0x170
[10051.084297] handle_edge_irq+0x215/0xb20
[10051.085122] asm_call_irq_on_stack+0xf/0x20
[10051.085986] common_interrupt+0xae/0x120
[10051.086830] asm_common_interrupt+0x1e/0x40
==================================================================
Bio will be checked at beginning of submit_bio_noacct(). If bio needs
to be throttled, it will start the timer and stop submit bio directly.
Bio will submit in blk_throtl_dispatch_work_fn() when the timer expires.
But in the current process, if bio is throttled, it will still set bio
issue->value by blkcg_bio_issue_init(). This is redundant and may cause
the above use-after-free.
CPU0 CPU1
submit_bio
submit_bio_noacct
submit_bio_checks
blk_throtl_bio()
<=mod_timer(&sq->pending_timer
blk_throtl_dispatch_work_fn
submit_bio_noacct() <= bio have
throttle tag, will throw directly
and bio issue->value will be set
here
bio_endio()
bio_put()
bio_free() <= free this bio
blkcg_bio_issue_init(bio)
<= bio has been freed and
will lead to UAF
return BLK_QC_T_NONE
Fix this by remove extra blkcg_bio_issue_init.
Fixes: e439bedf6b (blkcg: consolidate bio_issue_init() to be a part of core)
Signed-off-by: Laibin Qiu <qiulaibin@huawei.com>
Link: https://lore.kernel.org/r/20211112093354.3581504-1-qiulaibin@huawei.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42dc938a59 ]
Nothing protects the access to the per_cpu variable sd_llc_id. When testing
the same CPU (i.e. this_cpu == that_cpu), a race condition exists with
update_top_cache_domain(). One scenario being:
CPU1 CPU2
==================================================================
per_cpu(sd_llc_id, CPUX) => 0
partition_sched_domains_locked()
detach_destroy_domains()
cpus_share_cache(CPUX, CPUX) update_top_cache_domain(CPUX)
per_cpu(sd_llc_id, CPUX) => 0
per_cpu(sd_llc_id, CPUX) = CPUX
per_cpu(sd_llc_id, CPUX) => CPUX
return false
ttwu_queue_cond() wouldn't catch smp_processor_id() == cpu and the result
is a warning triggered from ttwu_queue_wakelist().
Avoid a such race in cpus_share_cache() by always returning true when
this_cpu == that_cpu.
Fixes: 518cd62341 ("sched: Only queue remote wakeups when crossing cache boundaries")
Reported-by: Jing-Ting Wu <jing-ting.wu@mediatek.com>
Signed-off-by: Vincent Donnefort <vincent.donnefort@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Reviewed-by: Vincent Guittot <vincent.guittot@linaro.org>
Link: https://lore.kernel.org/r/20211104175120.857087-1-vincent.donnefort@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5eeaafc8d6 ]
Several header files need info on CONFIG_32BIT or CONFIG_64BIT,
but kconfig symbol BCM63XX does not provide that info. This leads
to many build errors, e.g.:
arch/mips/include/asm/page.h:196:13: error: use of undeclared identifier 'CAC_BASE'
return x - PAGE_OFFSET + PHYS_OFFSET;
arch/mips/include/asm/mach-generic/spaces.h:91:23: note: expanded from macro 'PAGE_OFFSET'
#define PAGE_OFFSET (CAC_BASE + PHYS_OFFSET)
arch/mips/include/asm/io.h:134:28: error: use of undeclared identifier 'CAC_BASE'
return (void *)(address + PAGE_OFFSET - PHYS_OFFSET);
arch/mips/include/asm/mach-generic/spaces.h:91:23: note: expanded from macro 'PAGE_OFFSET'
#define PAGE_OFFSET (CAC_BASE + PHYS_OFFSET)
arch/mips/include/asm/uaccess.h:82:10: error: use of undeclared identifier '__UA_LIMIT'
return (__UA_LIMIT & (addr | (addr + size) | __ua_size(size))) == 0;
Selecting the SYS_HAS_CPU_BMIPS* symbols causes SYS_HAS_CPU_BMIPS to be
set, which then selects CPU_SUPPORT_32BIT_KERNEL, which causes
CONFIG_32BIT to be set. (a bit more indirect than v1 [RFC].)
Fixes: e7300d04bd ("MIPS: BCM63xx: Add support for the Broadcom BCM63xx family of SOCs.")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-mips@vger.kernel.org
Cc: Paul Burton <paulburton@kernel.org>
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Ralf Baechle <ralf@linux-mips.org>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05cf3ec00d ]
The gcc_aggre1_pnoc_ahb_clk is crucial for the proper MSM8996/APQ8096
functioning. If it gets disabled, several subsytems will stop working
(including eMMC/SDCC and USB). There are no in-kernel users of this
clock, so it is much simpler to remove from the kernel.
The clock was first removed in the commit 9e60de1cf2 ("clk: qcom:
Remove gcc_aggre1_pnoc_ahb_clk from msm8996") by Stephen Boyd, but got
added back in the commit b567752144 ("clk: qcom: Add some missing gcc
clks for msm8996") by Rajendra Nayak.
Let's remove it again in hope that nobody adds it back.
Reported-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Cc: Konrad Dybcio <konrad.dybcio@somainline.org>
Fixes: b567752144 ("clk: qcom: Add some missing gcc clks for msm8996")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20211104011155.2209654-1-dmitry.baryshkov@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f45c5b1c27 ]
Move the soc revision parsing to the initial probe, saving the driver
from parsing the register multiple times.
Use this variable to select the correct divisor table for the AHB clock.
Before this fix the A2 would have used the A0 table.
Fixes: 2d491066cc ("clk: ast2600: Fix AHB clock divider for A1")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210922235449.213631-1-joel@jms.id.au
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed84ef1cd7 ]
Two fixes in one:
- In the "impose hardware constraints" block, the "logical" divider
value (aka. not translated to the hardware) was clamped to fit in the
register area, but this totally ignored the fact that the divider
value can itself have a fixed divider.
- The code that made sure that the divider value returned by the
function was a multiple of its own fixed divider could result in a
wrong value being calculated, because it was rounded down instead of
rounded up.
Fixes: 4afe2d1a6e ("clk: ingenic: Allow divider value to be divided")
Co-developed-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20211001172033.122329-1-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca98d72141 ]
As Pavel Machek reported in [1]
This code looks quite confused: part of function returns 1 on
corruption, part returns -errno. The problem is not stable-specific.
[1] https://lkml.org/lkml/2021/9/19/207
Let's fix to make 'insane cp_payload case' to return 1 rater than
EFSCORRUPTED, so that return value can be kept consistent for all
error cases, it can avoid confusion of code logic.
Fixes: 65ddf65648 ("f2fs: fix to do sanity check for sb/cp fields correctly")
Reported-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02d58cd253 ]
Compresse file and normal file has differ in i_addr addressing,
specifically addrs per inode/block. So, we will face data loss, if we
disable the compression flag on non-empty files. Therefore we should
disallow not only enabling but disabling the compression flag on
non-empty files.
Fixes: 4c8ff7095b ("f2fs: support data compression")
Signed-off-by: Sungjong Seo <sj1557.seo@samsung.com>
Signed-off-by: Hyeong-Jun Kim <hj514.kim@samsung.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b929926f01 ]
Fix this by defining both ENDIAN macros in
<asm/sfp-machine.h> so that they can be utilized in
<math-emu/soft-fp.h> according to the latter's comment:
/* Allow sfp-machine to have its own byte order definitions. */
(This is what is done in arch/nds32/include/asm/sfp-machine.h.)
This placates these build warnings:
In file included from ../arch/sh/math-emu/math.c:23:
.../include/math-emu/single.h:50:21: warning: "__BIG_ENDIAN" is not defined, evaluates to 0 [-Wundef]
50 | #if __BYTE_ORDER == __BIG_ENDIAN
In file included from ../arch/sh/math-emu/math.c:24:
.../include/math-emu/double.h:59:21: warning: "__BIG_ENDIAN" is not defined, evaluates to 0 [-Wundef]
59 | #if __BYTE_ORDER == __BIG_ENDIAN
Fixes: 4b565680d1 ("sh: math-emu support")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Signed-off-by: Rich Felker <dalias@libc.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e25c252a9b ]
Delete ieee_fpe_handler() since it is not used. After that is done,
delete denormal_to_double() since it is not used:
.../arch/sh/math-emu/math.c:505:12: error: 'ieee_fpe_handler' defined but not used [-Werror=unused-function]
505 | static int ieee_fpe_handler(struct pt_regs *regs)
.../arch/sh/math-emu/math.c:477:13: error: 'denormal_to_double' defined but not used [-Werror=unused-function]
477 | static void denormal_to_double(struct sh_fpu_soft_struct *fpu, int n)
Fixes: 7caf62de25 ("sh: remove unused do_fpu_error")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Takashi YOSHII <takasi-y@ops.dti.ne.jp>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rich Felker <dalias@libc.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 011e0868e0 ]
Since active_logs can be set to 2 or 4 or NR_CURSEG_PERSIST_TYPE(6),
it cannot be set to NR_CURSEG_TYPE(8).
That is, whint_mode is always off.
Therefore, the condition is changed from NR_CURSEG_TYPE to NR_CURSEG_PERSIST_TYPE.
Cc: Chao Yu <chao@kernel.org>
Fixes: d0b9e42ab6 (f2fs: introduce inmem curseg)
Reported-by: tanghuan <tanghuan@vivo.com>
Signed-off-by: Keoseong Park <keosung.park@samsung.com>
Signed-off-by: Fengnan Chang <changfengnan@vivo.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 70a9ac36ff ]
Fix up a misuse that the filename pointer isn't always valid in
the ring buffer, and we should copy the content instead.
Fixes: 0c5e36db17 ("f2fs: trace f2fs_lookup")
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bde82ee391 ]
If KMEM_CACHE or maple_alloc_dev failed, the maple_bus_init() will return 0
rather than error, because the retval is not changed after KMEM_CACHE or
maple_alloc_dev failed.
Fixes: 17be2d2b1c ("sh: Add maple bus support for the SEGA Dreamcast.")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Lu Wei <luwei32@huawei.com>
Acked-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Signed-off-by: Rich Felker <dalias@libc.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fef071be57 ]
In dcr-low.S we use cmpli with three arguments, instead of four
arguments as defined in the ISA:
cmpli cr0,r3,1024
This appears to be a PPC440-ism, looking at the "PPC440x5 CPU Core
User’s Manual" it shows cmpli having no L field, but implied to be 0 due
to the core being 32-bit. It mentions that the ISA defines four
arguments and recommends using cmplwi.
It also corresponds to the old POWER instruction set, which had no L
field there, a reserved bit instead.
dcr-low.S is only built 32-bit, because it is only built when
DCR_NATIVE=y, which is only selected by 40x and 44x. Looking at the
generated code (with gcc/gas) we see cmplwi as expected.
Although gas is happy with the 3-argument version when building for
32-bit, the LLVM assembler is not and errors out with:
arch/powerpc/sysdev/dcr-low.S:27:10: error: invalid operand for instruction
cmpli 0,%r3,1024; ...
^
Switch to the cmplwi extended opcode, which avoids any confusion when
reading the ISA, fixes the issue with the LLVM assembler, and also means
the code could be built 64-bit in future (though that's very unlikely).
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
BugLink: https://github.com/ClangBuiltLinux/linux/issues/1419
Link: https://lore.kernel.org/r/20211014024424.528848-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94be878c88 ]
The length of hw->settings->odr_table is 2 and ref_sensor->id is an enum
variable whose value is between 0 and 5.
However, the value ST_LSM6DSX_ID_MAX (i.e. 5) is not caught properly in
switch (sensor->id) {
If ref_sensor->id is ST_LSM6DSX_ID_MAX, an array overflow will ocurrs in
function st_lsm6dsx_check_odr():
odr_table = &sensor->hw->settings->odr_table[sensor->id];
and in function st_lsm6dsx_set_odr():
reg = &hw->settings->odr_table[ref_sensor->id].reg;
To avoid this array overflow, handle ST_LSM6DSX_ID_GYRO explicitly and
return -EINVAL for the default case.
The enum value ST_LSM6DSX_ID_MAX is only present as an easy way to check
the limit and as such is never used, however this is not locally obvious.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Teng Qi <starmiku1207184332@gmail.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/20211011114003.976221-1-starmiku1207184332@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1283c0d1a3 ]
We can't free the tg_pt_gp in core_alua_set_tg_pt_gp_id() because it's
still accessed via configfs. Its release must go through the normal
configfs/refcount process.
The max alua_tg_pt_gps_count check should probably have been done in
core_alua_allocate_tg_pt_gp(), but with the current code userspace could
have created 0x0000ffff + 1 groups, but only set the id for 0x0000ffff.
Then it could have deleted a group with an ID set, and then set the ID for
that extra group and it would work ok.
It's unlikely, but just in case this patch continues to allow that type of
behavior, and just fixes the kfree() while in use bug.
Link: https://lore.kernel.org/r/20210930020422.92578-4-michael.christie@oracle.com
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed1227e080 ]
This patch fixes the following bugs:
1. If there are multiple ordered cmds queued and multiple simple cmds
completing, target_restart_delayed_cmds() could be called on different
CPUs and each instance could start a ordered cmd. They could then run in
different orders than they were queued.
2. target_restart_delayed_cmds() and target_handle_task_attr() can race
where:
1. target_handle_task_attr() has passed the simple_cmds == 0 check.
2. transport_complete_task_attr() then decrements simple_cmds to 0.
3. transport_complete_task_attr() runs target_restart_delayed_cmds() and
it does not see any cmds on the delayed_cmd_list.
4. target_handle_task_attr() adds the cmd to the delayed_cmd_list.
The cmd will then end up timing out.
3. If we are sent > 1 ordered cmds and simple_cmds == 0, we can execute
them out of order, because target_handle_task_attr() will hit that
simple_cmds check first and return false for all ordered cmds sent.
4. We run target_restart_delayed_cmds() after every cmd completion, so if
there is more than 1 simple cmd running, we start executing ordered cmds
after that first cmd instead of waiting for all of them to complete.
5. Ordered cmds are not supposed to start until HEAD OF QUEUE and all older
cmds have completed, and not just simple.
6. It's not a bug but it doesn't make sense to take the delayed_cmd_lock
for every cmd completion when ordered cmds are almost never used. Just
replacing that lock with an atomic increases IOPs by up to 10% when
completions are spread over multiple CPUs and there are multiple
sessions/ mqs/thread accessing the same device.
This patch moves the queued delayed handling to a per device work to
serialze the cmd executions for each device and adds a new counter to track
HEAD_OF_QUEUE and SIMPLE cmds. We can then check the new counter to
determine when to run the work on the completion path.
Link: https://lore.kernel.org/r/20210930020422.92578-3-michael.christie@oracle.com
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f347c26836 ]
The following issue was observed running syzkaller:
BUG: KASAN: slab-out-of-bounds in memcpy include/linux/string.h:377 [inline]
BUG: KASAN: slab-out-of-bounds in sg_copy_buffer+0x150/0x1c0 lib/scatterlist.c:831
Read of size 2132 at addr ffff8880aea95dc8 by task syz-executor.0/9815
CPU: 0 PID: 9815 Comm: syz-executor.0 Not tainted 4.19.202-00874-gfc0fe04215a9 #2
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xe4/0x14a lib/dump_stack.c:118
print_address_description+0x73/0x280 mm/kasan/report.c:253
kasan_report_error mm/kasan/report.c:352 [inline]
kasan_report+0x272/0x370 mm/kasan/report.c:410
memcpy+0x1f/0x50 mm/kasan/kasan.c:302
memcpy include/linux/string.h:377 [inline]
sg_copy_buffer+0x150/0x1c0 lib/scatterlist.c:831
fill_from_dev_buffer+0x14f/0x340 drivers/scsi/scsi_debug.c:1021
resp_report_tgtpgs+0x5aa/0x770 drivers/scsi/scsi_debug.c:1772
schedule_resp+0x464/0x12f0 drivers/scsi/scsi_debug.c:4429
scsi_debug_queuecommand+0x467/0x1390 drivers/scsi/scsi_debug.c:5835
scsi_dispatch_cmd+0x3fc/0x9b0 drivers/scsi/scsi_lib.c:1896
scsi_request_fn+0x1042/0x1810 drivers/scsi/scsi_lib.c:2034
__blk_run_queue_uncond block/blk-core.c:464 [inline]
__blk_run_queue+0x1a4/0x380 block/blk-core.c:484
blk_execute_rq_nowait+0x1c2/0x2d0 block/blk-exec.c:78
sg_common_write.isra.19+0xd74/0x1dc0 drivers/scsi/sg.c:847
sg_write.part.23+0x6e0/0xd00 drivers/scsi/sg.c:716
sg_write+0x64/0xa0 drivers/scsi/sg.c:622
__vfs_write+0xed/0x690 fs/read_write.c:485
kill_bdev:block_device:00000000e138492c
vfs_write+0x184/0x4c0 fs/read_write.c:549
ksys_write+0x107/0x240 fs/read_write.c:599
do_syscall_64+0xc2/0x560 arch/x86/entry/common.c:293
entry_SYSCALL_64_after_hwframe+0x49/0xbe
We get 'alen' from command its type is int. If userspace passes a large
length we will get a negative 'alen'.
Switch n, alen, and rlen to u32.
Link: https://lore.kernel.org/r/20211013033913.2551004-3-yebin10@huawei.com
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3968ddcf05 ]
When running ltp testcase(ltp/testcases/kernel/pty/pty04.c) with arm64, there is a soft lockup,
which look like this one:
Workqueue: events_unbound flush_to_ldisc
Call trace:
dump_backtrace+0x0/0x1ec
show_stack+0x24/0x30
dump_stack+0xd0/0x128
panic+0x15c/0x374
watchdog_timer_fn+0x2b8/0x304
__run_hrtimer+0x88/0x2c0
__hrtimer_run_queues+0xa4/0x120
hrtimer_interrupt+0xfc/0x270
arch_timer_handler_phys+0x40/0x50
handle_percpu_devid_irq+0x94/0x220
__handle_domain_irq+0x88/0xf0
gic_handle_irq+0x84/0xfc
el1_irq+0xc8/0x180
slip_unesc+0x80/0x214 [slip]
tty_ldisc_receive_buf+0x64/0x80
tty_port_default_receive_buf+0x50/0x90
flush_to_ldisc+0xbc/0x110
process_one_work+0x1d4/0x4b0
worker_thread+0x180/0x430
kthread+0x11c/0x120
In the testcase pty04, The first process call the write syscall to send
data to the pty master. At the same time, the workqueue will do the
flush_to_ldisc to pop data in a loop until there is no more data left.
When the sender and workqueue running in different core, the sender sends
data fastly in full time which will result in workqueue doing work in loop
for a long time and occuring softlockup in flush_to_ldisc with kernel
configured without preempt. So I add need_resched check and cond_resched
in the flush_to_ldisc loop to avoid it.
Signed-off-by: Guanghui Feng <guanghuifeng@linux.alibaba.com>
Link: https://lore.kernel.org/r/1633961304-24759-1-git-send-email-guanghuifeng@linux.alibaba.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c05f1477e ]
On m68k, compiling drivers under SND_ISA causes build errors:
../sound/core/isadma.c: In function 'snd_dma_program':
../sound/core/isadma.c:33:17: error: implicit declaration of function 'claim_dma_lock' [-Werror=implicit-function-declaration]
33 | flags = claim_dma_lock();
| ^~~~~~~~~~~~~~
../sound/core/isadma.c:41:9: error: implicit declaration of function 'release_dma_lock' [-Werror=implicit-function-declaration]
41 | release_dma_lock(flags);
| ^~~~~~~~~~~~~~~~
../sound/isa/sb/sb16_main.c: In function 'snd_sb16_playback_prepare':
../sound/isa/sb/sb16_main.c:253:72: error: 'DMA_AUTOINIT' undeclared (first use in this function)
253 | snd_dma_program(dma, runtime->dma_addr, size, DMA_MODE_WRITE | DMA_AUTOINIT);
| ^~~~~~~~~~~~
../sound/isa/sb/sb16_main.c:253:72: note: each undeclared identifier is reported only once for each function it appears in
../sound/isa/sb/sb16_main.c: In function 'snd_sb16_capture_prepare':
../sound/isa/sb/sb16_main.c:322:71: error: 'DMA_AUTOINIT' undeclared (first use in this function)
322 | snd_dma_program(dma, runtime->dma_addr, size, DMA_MODE_READ | DMA_AUTOINIT);
| ^~~~~~~~~~~~
and more...
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: alsa-devel@alsa-project.org
Cc: linux-m68k@lists.linux-m68k.org
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20211016062602.3588-1-rdunlap@infradead.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05e63b48b2 ]
We cannot list all the possible chips used in different board revisions,
just use the generic "jedec,spi-nor" compatible instead. This also
fixes dtbs_check error:
['jedec,spi-nor', 's25fl256s1', 's25fl512s'] is too long
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Reviewed-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ee1500ef7 ]
This fixes dtbs-check error from simple-bus schema:
soc: thermal-zones: {'type': 'object'} is not allowed for {'cpu-thermal': ..... }
From schema: /home/leo/.local/lib/python3.8/site-packages/dtschema/schemas/simple-bus.yaml
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51b9e22ffd ]
gpmc,mux-add-data is not boolean.
Fixes the below errors flagged by dtbs_check.
"ethernet@4,0:gpmc,mux-add-data: True is not of type 'array'"
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7a07f7b96 ]
The firmware_loader can be used with a pre-allocated buffer
through the use of the API calls:
o request_firmware_into_buf()
o request_partial_firmware_into_buf()
If the firmware was built-in and present, our current check
for if the built-in firmware fits into the pre-allocated buffer
does not return any errors, and we proceed to tell the caller
that everything worked fine. It's a lie and no firmware would
end up being copied into the pre-allocated buffer. So if the
caller trust the result it may end up writing a bunch of 0's
to a device!
Fix this by making the function that checks for the pre-allocated
buffer return non-void. Since the typical use case is when no
pre-allocated buffer is provided make this return successfully
for that case. If the built-in firmware does *not* fit into the
pre-allocated buffer size return a failure as we should have
been doing before.
I'm not aware of users of the built-in firmware using the API
calls with a pre-allocated buffer, as such I doubt this fixes
any real life issue. But you never know... perhaps some oddball
private tree might use it.
In so far as upstream is concerned this just fixes our code for
correctness.
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20210917182226.3532898-2-mcgrof@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f9d618696 ]
The csi_sel mux register is located in the CCM register base and not the
CCM_ANALOG register base. So move it to the correct position in code.
Otherwise changing the parent of the csi clock can lead to a complete
system failure due to the CCM_ANALOG_PLL_SYS_TOG register being falsely
modified.
Also remove the SET_RATE_PARENT flag since one possible supply for the
csi_sel mux is the system PLL which we don't want to modify.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20210927072857.3940880-1-s.riedmueller@phytec.de
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99a7cacc66 ]
According to Documentation/devicetree/bindings/watchdog/arm,sp805.yaml
the compatible is:
compatible = "arm,sp805", "arm,primecell";
The current compatible string doesn't exist at all. Fix it.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f1dcaff64 ]
The entry/exit latency and minimum residency in state for the idle
states of MSM8998 were ..bad: first of all, for all of them the
timings were written for CPU sleep but the min-residency-us param
was miscalculated (supposedly, while porting this from downstream);
Then, the power collapse states are setting PC on both the CPU
cluster *and* the L2 cache, which have different timings: in the
specific case of L2 the times are higher so these ones should be
taken into account instead of the CPU ones.
This parameter misconfiguration was not giving particular issues
because on MSM8998 there was no CPU scaling at all, so cluster/L2
power collapse was rarely (if ever) hit.
When CPU scaling is enabled, though, the wrong timings will produce
SoC unstability shown to the user as random, apparently error-less,
sudden reboots and/or lockups.
This set of parameters are stabilizing the SoC when CPU scaling is
ON and when power collapse is frequently hit.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210901183123.1087392-3-angelogioacchino.delregno@somainline.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6abc4ca5a2 ]
the switch identifies itself as a BCM53012 (rev 5)...
This patch has been tested & verified on OpenWrt's
snapshot with Linux 5.10 (didn't test any older kernels).
The MR32 is able to "talk to the network" as before with
OpenWrt's SWITCHDEV b53 driver.
| b53-srab-switch 18007000.ethernet-switch: found switch: BCM53012, rev 5
| libphy: dsa slave smi: probed
| b53-srab-switch 18007000.ethernet-switch poe (uninitialized):
| PHY [dsa-0.0:00] driver [Generic PHY] (irq=POLL)
| b53-srab-switch 18007000.ethernet-switch: Using legacy PHYLIB callbacks.
| Please migrate to PHYLINK!
| DSA: tree 0 setup
Reported-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7aee0288be ]
AUX2 has slightly wrong voltage and AUX5 doesn't need to be
always on.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9067839ff4 ]
Let's use SYSC_QUIRK_REINIT_ON_CTX_LOST quirk for am335x otg instead of
SYSC_QUIRK_REINIT_ON_RESUME quirk as we can now handle the context loss
in a more generic way.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d88136120 ]
Some interconnect target modules such as otg and gpmc on am335x need a
re-init after resume. As we also have PM runtime cases where the context
may be lost, let's handle these all with cpu_pm.
For the am335x resume path, we already have cpu_pm_resume() call
cpu_pm_cluster_exit().
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 894d4f1f77 ]
According to Documentation/devicetree/bindings/watchdog/arm,sp805.yaml
the compatible is:
compatible = "arm,sp805", "arm,primecell";
The current compatible string doesn't exist at all. Fix it.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2513fa5c25 ]
The CDN DP needs a PHY and a extcon to work correctly. But no extcon is
provided by the device-tree, which leads to an error:
cdn-dp fec00000.dp: [drm:cdn_dp_probe [rockchipdrm]] *ERROR* missing extcon or phy
cdn-dp: probe of fec00000.dp failed with error -22
Disable the CDN DP to make graphic work on the Pinebook Pro.
Reported-by: Guillaume Gardet <guillaume.gardet@arm.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Link: https://lore.kernel.org/r/20210715164101.11486-1-matthias.bgg@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99154581b0 ]
When parsing the txq list in lpfc_drain_txq(), the driver attempts to pass
the requests to the adapter. If such an attempt fails, a local "fail_msg"
string is set and a log message output. The job is then added to a
completions list for cancellation.
Processing of any further jobs from the txq list continues, but since
"fail_msg" remains set, jobs are added to the completions list regardless
of whether a wqe was passed to the adapter. If successfully added to
txcmplq, jobs are added to both lists resulting in list corruption.
Fix by clearing the fail_msg string after adding a job to the completions
list. This stops the subsequent jobs from being added to the completions
list unless they had an appropriate failure.
Link: https://lore.kernel.org/r/20210910233159.115896-2-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15a563d008 ]
Running dtbs_check yielded the issues with bcm-nsp.dtsi.
Firstly this patch fixes the following message by appending "-bus" to
the mpcore node name:
mpcore@19000000: $nodename:0: 'mpcore@19000000' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Secondly mmc node name. The label name can remain as is.
sdhci@21000: $nodename:0: 'sdhci@21000' does not match '^mmc(@.*)?$'
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 167721a590 ]
In kernel 5.4, support has been added for reading MTD devices via the nvmem
API.
For this the mtd devices are registered as read-only NVMEM providers under
sysfs with the same name as the flash partition label property.
So if flash partition label property of multiple flash devices are
identical then the second mtd device fails to get registered as a NVMEM
provider.
This patch fixes the issue by having different label property for different
flashes.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/6c4b9b9232b93d9e316a63c086540fd5bf6b8687.1623684253.git.michal.simek@xilinx.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Add these missing V4L2 controls. Tested binned and full resolution
modes in all four orientations using Raspberry Pi running libcamera.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
commit 98481f3d72 upstream.
The PCIe host bridge has two interrupt lines, one that goes towards it
PCIE_INTR2 second level interrupt controller and one for its MSI second
level interrupt controller. The first interrupt line is not currently
managed by the driver, which is why it was not a functional problem.
The interrupt-map property was also only listing the PCI_INTA interrupts
when there are also the INTB, C and D.
Reported-by: Jim Quinlan <jim2101024@gmail.com>
Fixes: d5c8dc0d4c ("ARM: dts: bcm2711: Enable PCIe controller")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add a second (identical) set of device nodes to allow concurrent use of the ISP
hardware by another user. This change effectively creates a second state
structure (struct bcm2835_isp_dev) to maintain independent state for the second
user. Node and media entity names are appened with the instance index
appropriately.
Further users can be added by changing the BCM2835_ISP_NUM_INSTANCES define.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
commit a72fdfd21e upstream.
Commit in Fixes changed the iopl emulation to not #GP on CLI and STI
because it would break some insane luserspace tools which would toggle
interrupts.
The corresponding selftest would rely on the fact that executing CLI/STI
would trigger a #GP and thus detect it this way but since that #GP is
not happening anymore, the detection is now wrong too.
Extend the test to actually look at the IF flag and whether executing
those insns had any effect on it. The STI detection needs to have the
fact that interrupts were previously disabled, passed in so do that from
the previous CLI test, i.e., STI test needs to follow a previous CLI one
for it to make sense.
Fixes: b968e84b50 ("x86/iopl: Fake iopl(3) CLI/STI usage")
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20211030083939.13073-1-bp@alien8.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 96cfe05051 upstream.
of_parse_thermal_zones() parses the thermal-zones node and registers a
thermal_zone device for each subnode. However, if a thermal zone is
consuming a thermal sensor and that thermal sensor device hasn't probed
yet, an attempt to set trip_point_*_temp for that thermal zone device
can cause a NULL pointer dereference. Fix it.
console:/sys/class/thermal/thermal_zone87 # echo 120000 > trip_point_0_temp
...
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000020
...
Call trace:
of_thermal_set_trip_temp+0x40/0xc4
trip_point_temp_store+0xc0/0x1dc
dev_attr_store+0x38/0x88
sysfs_kf_write+0x64/0xc0
kernfs_fop_write_iter+0x108/0x1d0
vfs_write+0x2f4/0x368
ksys_write+0x7c/0xec
__arm64_sys_write+0x20/0x30
el0_svc_common.llvm.7279915941325364641+0xbc/0x1bc
do_el0_svc+0x28/0xa0
el0_svc+0x14/0x24
el0_sync_handler+0x88/0xec
el0_sync+0x1c0/0x200
While at it, fix the possible NULL pointer dereference in other
functions as well: of_thermal_get_temp(), of_thermal_set_emul_temp(),
of_thermal_get_trend().
Suggested-by: David Collins <quic_collinsd@quicinc.com>
Signed-off-by: Subbaraman Narayanamurthy <quic_subbaram@quicinc.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4716023a8f upstream.
PEBS PERF_SAMPLE_PHYS_ADDR events use perf_virt_to_phys() to convert PMU
sampled virtual addresses to physical using get_user_page_fast_only()
and page_to_phys().
Some get_user_page_fast_only() error cases return false, indicating no
page reference, but still initialize the output page pointer with an
unreferenced page. In these error cases perf_virt_to_phys() calls
put_page(). This causes page reference count underflow, which can lead
to unintentional page sharing.
Fix perf_virt_to_phys() to only put_page() if get_user_page_fast_only()
returns a referenced page.
Fixes: fc7ce9c74c ("perf/core, x86: Add PERF_SAMPLE_PHYS_ADDR")
Signed-off-by: Greg Thelen <gthelen@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20211111021814.757086-1-gthelen@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is for linux-5.10.y only.
When scripts/lld-version.sh was initially written, it did not account
for the LLD_VENDOR cmake flag, which changes the output of ld.lld's
--version flag slightly.
Without LLD_VENDOR:
$ ld.lld --version
LLD 14.0.0 (compatible with GNU linkers)
With LLD_VENDOR:
$ ld.lld --version
Debian LLD 14.0.0 (compatible with GNU linkers)
As a result, CONFIG_LLD_VERSION is messed up and configuration values
that are dependent on it cannot be selected:
scripts/lld-version.sh: 20: printf: LLD: expected numeric value
scripts/lld-version.sh: 20: printf: LLD: expected numeric value
scripts/lld-version.sh: 20: printf: LLD: expected numeric value
init/Kconfig:52:warning: 'LLD_VERSION': number is invalid
.config:11:warning: symbol value '00000' invalid for LLD_VERSION
.config:8800:warning: override: CPU_BIG_ENDIAN changes choice state
This was fixed upstream by commit 1f09af0625 ("kbuild: Fix
ld-version.sh script if LLD was built with LLD_VENDOR") in 5.12 but that
was done to ld-version.sh after it was massively rewritten in
commit 02aff85922 ("kbuild: check the minimum linker version in
Kconfig").
To avoid bringing in that change plus its prerequisites and fixes, just
modify lld-version.sh to make it similar to the upstream ld-version.sh,
which handles ld.lld with or without LLD_VENDOR and ld.bfd without any
errors.
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 86432a6dca upstream.
There are pclusters in runtime marked with Z_EROFS_PCLUSTER_TAIL
before actual I/O submission. Thus, the decompression chain can be
extended if the following pcluster chain hooks such tail pcluster.
As the related comment mentioned, if some page is made of a hooked
pcluster and another followed pcluster, it can be reused for in-place
I/O (since I/O should be submitted anyway):
_______________________________________________________________
| tail (partial) page | head (partial) page |
|_____PRIMARY_HOOKED___|____________PRIMARY_FOLLOWED____________|
However, it's by no means safe to reuse as pagevec since if such
PRIMARY_HOOKED pclusters finally move into bypass chain without I/O
submission. It's somewhat hard to reproduce with LZ4 and I just found
it (general protection fault) by ro_fsstressing a LZMA image for long
time.
I'm going to actively clean up related code together with multi-page
folio adaption in the next few months. Let's address it directly for
easier backporting for now.
Call trace for reference:
z_erofs_decompress_pcluster+0x10a/0x8a0 [erofs]
z_erofs_decompress_queue.isra.36+0x3c/0x60 [erofs]
z_erofs_runqueue+0x5f3/0x840 [erofs]
z_erofs_readahead+0x1e8/0x320 [erofs]
read_pages+0x91/0x270
page_cache_ra_unbounded+0x18b/0x240
filemap_get_pages+0x10a/0x5f0
filemap_read+0xa9/0x330
new_sync_read+0x11b/0x1a0
vfs_read+0xf1/0x190
Link: https://lore.kernel.org/r/20211103182006.4040-1-xiang@kernel.org
Fixes: 3883a79abd ("staging: erofs: introduce VLE decompression support")
Cc: <stable@vger.kernel.org> # 4.19+
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ec18fc783 upstream.
commit 8779e05ba8 ("parisc: Fix ptrace check on syscall return")
fixed testing of TI_FLAGS. This uncovered a bug in the test mask.
syscall_restore_rfi is only used when the kernel needs to exit to
usespace with single or block stepping and the recovery counter
enabled. The test however used _TIF_SYSCALL_TRACE_MASK, which
includes a lot of bits that shouldn't be tested here.
Fix this by using TIF_SINGLESTEP and TIF_BLOCKSTEP directly.
I encountered this bug by enabling syscall tracepoints. Both in qemu and
on real hardware. As soon as i enabled the tracepoint (sys_exit_read,
but i guess it doesn't really matter which one), i got random page
faults in userspace almost immediately.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b968e84b50 upstream.
Since commit c8137ace56 ("x86/iopl: Restrict iopl() permission
scope") it's possible to emulate iopl(3) using ioperm(), except for
the CLI/STI usage.
Userspace CLI/STI usage is very dubious (read broken), since any
exception taken during that window can lead to rescheduling anyway (or
worse). The IOPL(2) manpage even states that usage of CLI/STI is highly
discouraged and might even crash the system.
Of course, that won't stop people and HP has the dubious honour of
being the first vendor to be found using this in their hp-health
package.
In order to enable this 'software' to still 'work', have the #GP treat
the CLI/STI instructions as NOPs when iopl(3). Warn the user that
their program is doing dubious things.
Fixes: a24ca99768 ("x86/iopl: Remove legacy IOPL option")
Reported-by: Ondrej Zary <linux@zary.sk>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org # v5.5+
Link: https://lkml.kernel.org/r/20210918090641.GD5106@worktop.programming.kicks-ass.net
Signed-off-by: Ondrej Zary <linux@zary.sk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2d26f6e39a upstream.
This reverts commit 2c896fb02e
"net: stmmac: dwmac-rk: add pd_gmac support for rk3399" and fixes
unbalanced pm_runtime_enable warnings.
In the commit to be reverted, support for power management was
introduced to the Rockchip glue code. Later, power management support
was introduced to the stmmac core code, resulting in multiple
invocations of pm_runtime_{enable,disable,get_sync,put_sync}.
The multiple invocations happen in rk_gmac_powerup and
stmmac_{dvr_probe, resume} as well as in rk_gmac_powerdown and
stmmac_{dvr_remove, suspend}, respectively, which are always called
in conjunction.
Fixes: 5ec5582343 ("net: stmmac: add clocks management for gmac driver")
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4691ffb18a upstream.
Fix system hang with below sequences:
~# ifconfig ethx down
~# ifconfig ethx hw ether xx:xx:xx:xx:xx:xx
After ethx down, stmmac all clocks gated off and then register access causes
system hang.
Fixes: 5ec5582343 ("net: stmmac: add clocks management for gmac driver")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ec05a6035 upstream
Get rid of the CONFIG_PM_SLEEP ifdefery to fix the build error
and use __maybe_unused for the suspend()/resume() hooks to avoid
build warning:
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:769:21:
error: 'stmmac_runtime_suspend' undeclared here (not in a function); did you mean 'stmmac_suspend'?
769 | SET_RUNTIME_PM_OPS(stmmac_runtime_suspend, stmmac_runtime_resume, NULL)
| ^~~~~~~~~~~~~~~~~~~~~~
./include/linux/pm.h:342:21: note: in definition of macro 'SET_RUNTIME_PM_OPS'
342 | .runtime_suspend = suspend_fn, \
| ^~~~~~~~~~
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:769:45:
error: 'stmmac_runtime_resume' undeclared here (not in a function)
769 | SET_RUNTIME_PM_OPS(stmmac_runtime_suspend, stmmac_runtime_resume, NULL)
| ^~~~~~~~~~~~~~~~~~~~~
./include/linux/pm.h:343:20: note: in definition of macro 'SET_RUNTIME_PM_OPS'
343 | .runtime_resume = resume_fn, \
| ^~~~~~~~~
Fixes: 5ec5582343 ("net: stmmac: add clocks management for gmac driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ec5582343 upstream.
This patch intends to add clocks management for stmmac driver:
If CONFIG_PM enabled:
1. Keep clocks disabled after driver probed.
2. Enable clocks when up the net device, and disable clocks when down
the net device.
If CONFIG_PM disabled:
Keep clocks always enabled after driver probed.
Note:
1. It is fine for ethtool, since the way of implementing ethtool_ops::begin
in stmmac is only can be accessed when interface is enabled, so the clocks
are ticked.
2. The MDIO bus has a different life cycle to the MAC, need ensure
clocks are enabled when _mdio_read/write() need clocks, because these
functions can be called while the interface it not opened.
Stable backport notes:
When run below command to remove ethernet driver on
stratix10 platform, there will be warning trace as below:
$ cd /sys/class/net/eth0/device/driver/
$ echo ff800000.ethernet > unbind
WARNING: CPU: 3 PID: 386 at drivers/clk/clk.c:810 clk_core_unprepare+0x114/0x274
Modules linked in: sch_fq_codel
CPU: 3 PID: 386 Comm: sh Tainted: G W 5.10.74-yocto-standard #1
Hardware name: SoCFPGA Stratix 10 SoCDK (DT)
pstate: 00000005 (nzcv daif -PAN -UAO -TCO BTYPE=--)
pc : clk_core_unprepare+0x114/0x274
lr : clk_core_unprepare+0x114/0x274
sp : ffff800011bdbb10
clk_core_unprepare+0x114/0x274
clk_unprepare+0x38/0x50
stmmac_remove_config_dt+0x40/0x80
stmmac_pltfr_remove+0x64/0x80
platform_drv_remove+0x38/0x60
... ..
el0_sync_handler+0x1a4/0x1b0
el0_sync+0x180/0x1c0
This issue is introduced by introducing upstream commit 8f269102ba
("net: stmmac: disable clocks in stmmac_remove_config_dt()")
But in latest mainline kernel, there is no this issue. Because this
patch improved clocks management for stmmac driver.
Therefore, backport it and its fixing patches to stable kernel v5.10.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: stable@vger.kernel.org
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 541ac97186 upstream.
The size of the exception stacks was increased by the commit in Fixes,
resulting in stack sizes greater than a page in size. The #VC exception
handling was only mapping the first (bottom) page, resulting in an
SEV-ES guest failing to boot.
Make the #VC exception stacks part of the default exception stacks
storage and allocate them with a CONFIG_AMD_MEM_ENCRYPT=y .config. Map
them only when a SEV-ES guest has been detected.
Rip out the custom VC stacks mapping and storage code.
[ bp: Steal and adapt Tom's commit message. ]
Fixes: 7fae4c24a2 ("x86: Increase exception stack sizes")
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Tested-by: Brijesh Singh <brijesh.singh@amd.com>
Link: https://lkml.kernel.org/r/YVt1IMjIs7pIZTRR@zn.tnic
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a20eac0af0 upstream.
Previous fix aded bpf_clamp_umax() helper use to re-validate boundaries.
While that works correctly, it introduces more branches, which blows up
past 1 million instructions in no-alu32 variant of strobemeta selftests.
Switching len variable from u32 to u64 also fixes the issue and reduces
the number of validated instructions, so use that instead. Fix this
patch and bpf_clamp_umax() removed, both alu32 and no-alu32 selftests
pass.
Fixes: 0133c20480 ("selftests/bpf: Fix strobemeta selftest regression")
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20211101230118.1273019-1-andrii@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0eab756f88 upstream.
There are several error return paths that dereference the null pointer
host because the pointer has not yet been set to a valid value.
Fix this by adding a new out_mmc label and exiting via this label
to avoid the host clean up and hence the null pointer dereference.
Addresses-Coverity: ("Explicit null dereference")
Fixes: 8105c2abbf ("mmc: moxart: Fix reference count leaks in moxart_probe")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20211013100052.125461-1-colin.king@canonical.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 937e79c677 upstream.
Using a kernel pointer in place of a dma_addr_t token can
lead to undefined behavior if that makes it into cache
management functions. The compiler caught one such attempt
in a cast:
drivers/net/wireless/ath/ath10k/mac.c: In function 'ath10k_add_interface':
drivers/net/wireless/ath/ath10k/mac.c:5586:47: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
5586 | arvif->beacon_paddr = (dma_addr_t)arvif->beacon_buf;
| ^
Looking through how this gets used down the way, I'm fairly
sure that beacon_paddr is never accessed again for ATH10K_DEV_TYPE_HL
devices, and if it was accessed, that would be a bug.
Change the assignment to use a known-invalid address token
instead, which avoids the warning and makes it easier to catch
bugs if it does end up getting used.
Fixes: e263bdab9c ("ath10k: high latency fixes for beacon buffer")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211014075153.3655910-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea7a1019d8 upstream.
The premise of commit 6f9f17287e ("SUNRPC: Mitigate cond_resched() in
xprt_transmit()") was that cond_resched() is expensive and unnecessary
when there has been just a single send.
The point of cond_resched() is to ensure that tasks that should pre-empt
this one get a chance to do so when it is safe to do so. The code prior
to commit 6f9f17287e failed to take into account that it was keeping a
rpc_task pinned for longer than it needed to, and so rather than doing a
full revert, let's just move the cond_resched.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4e17d65da upstream.
Change PCIe Max Payload Size setting in PCIe Device Control register to 512
bytes to align with PCIe Link Initialization sequence as defined in Marvell
Armada 3700 Functional Specification. According to the specification,
maximal Max Payload Size supported by this device is 512 bytes.
Without this kernel prints suspicious line:
pci 0000:01:00.0: Upstream bridge's Max Payload Size set to 256 (was 16384, max 512)
With this change it changes to:
pci 0000:01:00.0: Upstream bridge's Max Payload Size set to 256 (was 512, max 512)
Link: https://lore.kernel.org/r/20211005180952.6812-3-kabel@kernel.org
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c45361abb9 upstream.
When CONFIG_SMP=y, timebase synchronization is required when the second
kernel is started.
arch/powerpc/kernel/smp.c:
int __cpu_up(unsigned int cpu, struct task_struct *tidle)
{
...
if (smp_ops->give_timebase)
smp_ops->give_timebase();
...
}
void start_secondary(void *unused)
{
...
if (smp_ops->take_timebase)
smp_ops->take_timebase();
...
}
When CONFIG_HOTPLUG_CPU=n and CONFIG_KEXEC_CORE=n,
smp_85xx_ops.give_timebase is NULL,
smp_85xx_ops.take_timebase is NULL,
As a result, the timebase is not synchronized.
Timebase synchronization does not depend on CONFIG_HOTPLUG_CPU.
Fixes: 56f1ba2807 ("powerpc/mpc85xx: refactor the PM operations")
Cc: stable@vger.kernel.org # v4.6+
Signed-off-by: Xiaoming Ni <nixiaoming@huawei.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210929033646.39630-3-nixiaoming@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e3cdba176 upstream.
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: dbffc8ccdf ("mtd: rawnand: au1550: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-3-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 325fd539fc upstream.
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 612e048e6a ("mtd: rawnand: plat_nand: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-8-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 194ac63de6 upstream.
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 553508cec2 ("mtd: rawnand: orion: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-6-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f16b7d2a5e upstream.
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 8fc6f1f042 ("mtd: rawnand: pasemi: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-7-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5b5b4dc6f upstream.
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: f6341f6448 ("mtd: rawnand: gpio: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-4-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9d8570b7f upstream.
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 6dd09f775b ("mtd: rawnand: mpc5121: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-5-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6bcd2960af upstream.
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: d525914b5b ("mtd: rawnand: xway: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Cc: Jan Hoffmann <jan@3e8.eu>
Cc: Kestrel seventyfour <kestrelseventyfour@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Jan Hoffmann <jan@3e8.eu>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-10-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d707bb74da upstream.
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 59d9347332 ("mtd: rawnand: ams-delta: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-2-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad9a145172 upstream.
Since commit 48720ba568 ("virtio/s390: use DMA memory for ccw I/O and
classic notifiers") we were supposed to make sure that
virtio_ccw_release_dev() completes before the ccw device and the
attached dma pool are torn down, but unfortunately we did not. Before
that commit it used to be OK to delay cleaning up the memory allocated
by virtio-ccw indefinitely (which isn't really intuitive for guys used
to destruction happens in reverse construction order), but now we
trigger a BUG_ON if the genpool is destroyed before all memory allocated
from it is deallocated. Which brings down the guest. We can observe this
problem, when unregister_virtio_device() does not give up the last
reference to the virtio_device (e.g. because a virtio-scsi attached scsi
disk got removed without previously unmounting its previously mounted
partition).
To make sure that the genpool is only destroyed after all the necessary
freeing is done let us take a reference on the ccw device on each
ccw_device_dma_zalloc() and give it up on each ccw_device_dma_free().
Actually there are multiple approaches to fixing the problem at hand
that can work. The upside of this one is that it is the safest one while
remaining simple. We don't crash the guest even if the driver does not
pair allocations and frees. The downside is the reference counting
overhead, that the reference counting for ccw devices becomes more
complex, in a sense that we need to pair the calls to the aforementioned
functions for it to be correct, and that if we happen to leak, we leak
more than necessary (the whole ccw device instead of just the genpool).
Some alternatives to this approach are taking a reference in
virtio_ccw_online() and giving it up in virtio_ccw_release_dev() or
making sure virtio_ccw_release_dev() completes its work before
virtio_ccw_remove() returns. The downside of these approaches is that
these are less safe against programming errors.
Cc: <stable@vger.kernel.org> # v5.3
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Fixes: 48720ba568 ("virtio/s390: use DMA memory for ccw I/O and classic notifiers")
Reported-by: bfu@redhat.com
Reviewed-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3826350e6d upstream.
When a queue is switched to soft offline during heavy load and later
switched to soft online again and now used, it may be that the caller
is blocked forever in the ioctl call.
The failure occurs because there is a pending reply after the queue(s)
have been switched to offline. This orphaned reply is received when
the queue is switched to online and is accidentally counted for the
outstanding replies. So when there was a valid outstanding reply and
this orphaned reply is received it counts as the outstanding one thus
dropping the outstanding counter to 0. Voila, with this counter the
receive function is not called any more and the real outstanding reply
is never received (until another request comes in...) and the ioctl
blocks.
The fix is simple. However, instead of readjusting the counter when an
orphaned reply is detected, I check the queue status for not empty and
compare this to the outstanding counter. So if the queue is not empty
then the counter must not drop to 0 but at least have a value of 1.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 213fca9e23 upstream.
commit 9c6c273aa4 ("timer: Remove init_timer_on_stack() in favor
of timer_setup_on_stack()") changed the timer setup from
init_timer_on_stack(() to timer_setup(), but missed to change the
mod_timer() call. And while at it, use msecs_to_jiffies() instead
of the open coded timeout calculation.
Cc: stable@vger.kernel.org
Fixes: 9c6c273aa4 ("timer: Remove init_timer_on_stack() in favor of timer_setup_on_stack()")
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33a5471f8d upstream.
The note in c2adda27d2 ("video: backlight: Add of_find_backlight helper
in backlight.c") says that gpio-backlight uses brightness as power state.
This has been fixed since in ec665b756e ("backlight: gpio-backlight:
Correct initial power state handling") and other backlight drivers do not
require this workaround. Drop the workaround.
This fixes the case where e.g. pwm-backlight can perfectly well be set to
brightness 0 on boot in DT, which without this patch leads to the display
brightness to be max instead of off.
Fixes: c2adda27d2 ("video: backlight: Add of_find_backlight helper in backlight.c")
Cc: <stable@vger.kernel.org> # 5.4+
Cc: <stable@vger.kernel.org> # 4.19.x: ec665b756e: backlight: gpio-backlight: Correct initial power state handling
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60e2793d44 upstream.
Any allocation failure during the #PF path will return with VM_FAULT_OOM
which in turn results in pagefault_out_of_memory. This can happen for 2
different reasons. a) Memcg is out of memory and we rely on
mem_cgroup_oom_synchronize to perform the memcg OOM handling or b)
normal allocation fails.
The latter is quite problematic because allocation paths already trigger
out_of_memory and the page allocator tries really hard to not fail
allocations. Anyway, if the OOM killer has been already invoked there
is no reason to invoke it again from the #PF path. Especially when the
OOM condition might be gone by that time and we have no way to find out
other than allocate.
Moreover if the allocation failed and the OOM killer hasn't been invoked
then we are unlikely to do the right thing from the #PF context because
we have already lost the allocation context and restictions and
therefore might oom kill a task from a different NUMA domain.
This all suggests that there is no legitimate reason to trigger
out_of_memory from pagefault_out_of_memory so drop it. Just to be sure
that no #PF path returns with VM_FAULT_OOM without allocation print a
warning that this is happening before we restart the #PF.
[VvS: #PF allocation can hit into limit of cgroup v1 kmem controller.
This is a local problem related to memcg, however, it causes unnecessary
global OOM kills that are repeated over and over again and escalate into a
real disaster. This has been broken since kmem accounting has been
introduced for cgroup v1 (3.8). There was no kmem specific reclaim for
the separate limit so the only way to handle kmem hard limit was to return
with ENOMEM. In upstream the problem will be fixed by removing the
outdated kmem limit, however stable and LTS kernels cannot do it and are
still affected. This patch fixes the problem and should be backported
into stable/LTS.]
Link: https://lkml.kernel.org/r/f5fd8dd8-0ad4-c524-5f65-920b01972a42@virtuozzo.com
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Roman Gushchin <guro@fb.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Cc: Uladzislau Rezki <urezki@gmail.com>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b28179a61 upstream.
Patch series "memcg: prohibit unconditional exceeding the limit of dying tasks", v3.
Memory cgroup charging allows killed or exiting tasks to exceed the hard
limit. It can be misused and allowed to trigger global OOM from inside
a memcg-limited container. On the other hand if memcg fails allocation,
called from inside #PF handler it triggers global OOM from inside
pagefault_out_of_memory().
To prevent these problems this patchset:
(a) removes execution of out_of_memory() from
pagefault_out_of_memory(), becasue nobody can explain why it is
necessary.
(b) allow memcg to fail allocation of dying/killed tasks.
This patch (of 3):
Any allocation failure during the #PF path will return with VM_FAULT_OOM
which in turn results in pagefault_out_of_memory which in turn executes
out_out_memory() and can kill a random task.
An allocation might fail when the current task is the oom victim and
there are no memory reserves left. The OOM killer is already handled at
the page allocator level for the global OOM and at the charging level
for the memcg one. Both have much more information about the scope of
allocation/charge request. This means that either the OOM killer has
been invoked properly and didn't lead to the allocation success or it
has been skipped because it couldn't have been invoked. In both cases
triggering it from here is pointless and even harmful.
It makes much more sense to let the killed task die rather than to wake
up an eternally hungry oom-killer and send him to choose a fatter victim
for breakfast.
Link: https://lkml.kernel.org/r/0828a149-786e-7c06-b70a-52d086818ea3@virtuozzo.com
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Suggested-by: Michal Hocko <mhocko@suse.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Roman Gushchin <guro@fb.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Cc: Uladzislau Rezki <urezki@gmail.com>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4ebf1b6ca upstream.
Memory cgroup charging allows killed or exiting tasks to exceed the hard
limit. It is assumed that the amount of the memory charged by those
tasks is bound and most of the memory will get released while the task
is exiting. This is resembling a heuristic for the global OOM situation
when tasks get access to memory reserves. There is no global memory
shortage at the memcg level so the memcg heuristic is more relieved.
The above assumption is overly optimistic though. E.g. vmalloc can
scale to really large requests and the heuristic would allow that. We
used to have an early break in the vmalloc allocator for killed tasks
but this has been reverted by commit b8c8a338f7 ("Revert "vmalloc:
back off when the current task is killed""). There are likely other
similar code paths which do not check for fatal signals in an
allocation&charge loop. Also there are some kernel objects charged to a
memcg which are not bound to a process life time.
It has been observed that it is not really hard to trigger these
bypasses and cause global OOM situation.
One potential way to address these runaways would be to limit the amount
of excess (similar to the global OOM with limited oom reserves). This
is certainly possible but it is not really clear how much of an excess
is desirable and still protects from global OOMs as that would have to
consider the overall memcg configuration.
This patch is addressing the problem by removing the heuristic
altogether. Bypass is only allowed for requests which either cannot
fail or where the failure is not desirable while excess should be still
limited (e.g. atomic requests). Implementation wise a killed or dying
task fails to charge if it has passed the OOM killer stage. That should
give all forms of reclaim chance to restore the limit before the failure
(ENOMEM) and tell the caller to back off.
In addition, this patch renames should_force_charge() helper to
task_is_dying() because now its use is not associated witch forced
charging.
This patch depends on pagefault_out_of_memory() to not trigger
out_of_memory(), because then a memcg failure can unwind to VM_FAULT_OOM
and cause a global OOM killer.
Link: https://lkml.kernel.org/r/8f5cebbb-06da-4902-91f0-6566fc4b4203@virtuozzo.com
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Suggested-by: Michal Hocko <mhocko@suse.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: Uladzislau Rezki <urezki@gmail.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3dc20f4762 ]
Currently, it is not possible to migrate a neighbor entry between NUD_PERMANENT
state and NTF_USE flag with a dynamic NUD state from a user space control plane.
Similarly, it is not possible to add/remove NTF_EXT_LEARNED flag from an existing
neighbor entry in combination with NTF_USE flag.
This is due to the latter directly calling into neigh_event_send() without any
meta data updates as happening in __neigh_update(). Thus, to enable this use
case, extend the latter with a NEIGH_UPDATE_F_USE flag where we break the
NUD_PERMANENT state in particular so that a latter neigh_event_send() is able
to re-resolve a neighbor entry.
Before fix, NUD_PERMANENT -> NUD_* & NTF_USE:
# ./ip/ip n replace 192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a PERMANENT
[...]
# ./ip/ip n replace 192.168.178.30 dev enp5s0 use extern_learn
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a PERMANENT
[...]
As can be seen, despite the admin-triggered replace, the entry remains in the
NUD_PERMANENT state.
After fix, NUD_PERMANENT -> NUD_* & NTF_USE:
# ./ip/ip n replace 192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a PERMANENT
[...]
# ./ip/ip n replace 192.168.178.30 dev enp5s0 use extern_learn
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a extern_learn REACHABLE
[...]
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a extern_learn STALE
[...]
# ./ip/ip n replace 192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a PERMANENT
[...]
After the fix, the admin-triggered replace switches to a dynamic state from
the NTF_USE flag which triggered a new neighbor resolution. Likewise, we can
transition back from there, if needed, into NUD_PERMANENT.
Similar before/after behavior can be observed for below transitions:
Before fix, NTF_USE -> NTF_USE | NTF_EXT_LEARNED -> NTF_USE:
# ./ip/ip n replace 192.168.178.30 dev enp5s0 use
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a REACHABLE
[...]
# ./ip/ip n replace 192.168.178.30 dev enp5s0 use extern_learn
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a REACHABLE
[...]
After fix, NTF_USE -> NTF_USE | NTF_EXT_LEARNED -> NTF_USE:
# ./ip/ip n replace 192.168.178.30 dev enp5s0 use
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a REACHABLE
[...]
# ./ip/ip n replace 192.168.178.30 dev enp5s0 use extern_learn
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a extern_learn REACHABLE
[...]
# ./ip/ip n replace 192.168.178.30 dev enp5s0 use
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a REACHABLE
[..]
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Roopa Prabhu <roopa@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 69ea463021 upstream.
When using "devm_request_threaded_irq(,,,,IRQF_ONESHOT,,)" in a driver,
only the first interrupt is handled, and following interrupts are never
delivered (initially reported in [1]).
That's because the RISC-V PLIC cannot EOI masked interrupts, as explained
in the description of Interrupt Completion in the PLIC spec [2]:
<quote>
The PLIC signals it has completed executing an interrupt handler by
writing the interrupt ID it received from the claim to the claim/complete
register. The PLIC does not check whether the completion ID is the same
as the last claim ID for that target. If the completion ID does not match
an interrupt source that *is currently enabled* for the target, the
completion is silently ignored.
</quote>
Re-enable the interrupt before completion if it has been masked during
the handling, and remask it afterwards.
[1] http://lists.infradead.org/pipermail/linux-riscv/2021-July/007441.html
[2] 8bc15a35d0/riscv-plic.adoc
Fixes: bb0fed1c60 ("irqchip/sifive-plic: Switch to fasteoi flow")
Reported-by: Vincent Pelletier <plr.vincent@gmail.com>
Tested-by: Nikita Shubin <nikita.shubin@maquefel.me>
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Cc: stable@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
[maz: amended commit message]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211105094748.3894453-1-guoren@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca7752caea upstream.
copy_process currently copies task_struct.posix_cputimers_work as-is. If a
timer interrupt arrives while handling clone and before dup_task_struct
completes then the child task will have:
1. posix_cputimers_work.scheduled = true
2. posix_cputimers_work.work queued.
copy_process clears task_struct.task_works, so (2) will have no effect and
posix_cpu_timers_work will never run (not to mention it doesn't make sense
for two tasks to share a common linked list).
Since posix_cpu_timers_work never runs, posix_cputimers_work.scheduled is
never cleared. Since scheduled is set, future timer interrupts will skip
scheduling work, with the ultimate result that the task will never receive
timer expirations.
Together, the complete flow is:
1. Task 1 calls clone(), enters kernel.
2. Timer interrupt fires, schedules task work on Task 1.
2a. task_struct.posix_cputimers_work.scheduled = true
2b. task_struct.posix_cputimers_work.work added to
task_struct.task_works.
3. dup_task_struct() copies Task 1 to Task 2.
4. copy_process() clears task_struct.task_works for Task 2.
5. Future timer interrupts on Task 2 see
task_struct.posix_cputimers_work.scheduled = true and skip scheduling
work.
Fix this by explicitly clearing contents of task_struct.posix_cputimers_work
in copy_process(). This was never meant to be shared or inherited across
tasks in the first place.
Fixes: 1fb497dd00 ("posix-cpu-timers: Provide mechanisms to defer timer handling to task_work")
Reported-by: Rhys Hiltner <rhys@justin.tv>
Signed-off-by: Michael Pratt <mpratt@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211101210615.716522-1-mpratt@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a923a2676e upstream.
Fix assembly errors like:
{standard input}: Assembler messages:
{standard input}:287: Error: opcode not supported on this processor: mips3 (mips3) `dins $10,$7,32,32'
{standard input}:680: Error: opcode not supported on this processor: mips3 (mips3) `dins $10,$7,32,32'
{standard input}:1274: Error: opcode not supported on this processor: mips3 (mips3) `dins $12,$9,32,32'
{standard input}:2175: Error: opcode not supported on this processor: mips3 (mips3) `dins $10,$7,32,32'
make[1]: *** [scripts/Makefile.build:277: mm/highmem.o] Error 1
with code produced from `__cmpxchg64' for MIPS64r2 CPU configurations
using CONFIG_32BIT and CONFIG_PHYS_ADDR_T_64BIT.
This is due to MIPS_ISA_ARCH_LEVEL downgrading the assembly architecture
to `r4000' i.e. MIPS III for MIPS64r2 configurations, while there is a
block of code containing a DINS MIPS64r2 instruction conditionalized on
MIPS_ISA_REV >= 2 within the scope of the downgrade.
The assembly architecture override code pattern has been put there for
LL/SC instructions, so that code compiles for configurations that select
a processor to build for that does not support these instructions while
still providing run-time support for processors that do, dynamically
switched by non-constant `cpu_has_llsc'. It went in with linux-mips.org
commit aac8aa7717 ("Enable a suitable ISA for the assembler around
ll/sc so that code builds even for processors that don't support the
instructions. Plus minor formatting fixes.") back in 2005.
Fix the problem by wrapping these instructions along with the adjacent
SYNC instructions only, following the practice established with commit
cfd54de3b0 ("MIPS: Avoid move psuedo-instruction whilst using
MIPS_ISA_LEVEL") and commit 378ed6f0e3 ("MIPS: Avoid using .set mips0
to restore ISA"). Strictly speaking the SYNC instructions do not have
to be wrapped as they are only used as a Loongson3 erratum workaround,
so they will be enabled in the assembler by default, but do this so as
to keep code consistent with other places.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: c7e2d71dda ("MIPS: Fix set_pte() for Netlogic XLR using cmpxchg64()")
Cc: stable@vger.kernel.org # v5.1+
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 279917e27e upstream.
I noticed that sometimes at kernel startup the backtraces did not
included the function names of init functions. Their address were not
resolved to function names and instead only the address was printed.
Debugging shows that the culprit is is_ksym_addr() which is called
by the backtrace functions to check if an address belongs to a function in
the kernel. The problem occurs only for CONFIG_KALLSYMS_ALL=y.
When looking at is_ksym_addr() one can see that for CONFIG_KALLSYMS_ALL=y
the function only tries to resolve the address via is_kernel() function,
which checks like this:
if (addr >= _stext && addr <= _end)
return 1;
On parisc the init functions are located before _stext, so this check fails.
Other platforms seem to have all functions (including init functions)
behind _stext.
The following patch moves the _stext symbol at the beginning of the
kernel and thus includes the init section. This fixes the check and does
not seem to have any negative side effects on where the kernel mapping
happens in the map_pages() function in arch/parisc/mm/init.c.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@kernel.org # 5.4+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 418ace9992 upstream.
Naresh and Antonio ran into a build failure with latest Debian
armhf compilers, with lots of output like
tmp/ccY3nOAs.s:2215: Error: selected processor does not support `cpsid i' in ARM mode
As it turns out, $(cc-option) fails early here when the FPU is not
selected before CPU architecture is selected, as the compiler
option check runs before enabling -msoft-float, which causes
a problem when testing a target architecture level without an FPU:
cc1: error: '-mfloat-abi=hard': selected architecture lacks an FPU
Passing e.g. -march=armv6k+fp in place of -march=armv6k would avoid this
issue, but the fallback logic is already broken because all supported
compilers (gcc-5 and higher) are much more recent than these options,
and building with -march=armv5t as a fallback no longer works.
The best way forward that I see is to just remove all the checks, which
also has the nice side-effect of slightly improving the startup time for
'make'.
The -mtune=marvell-f option was apparently never supported by any mainline
compiler, and the custom Codesourcery gcc build that did support is
now too old to build kernels, so just use -mtune=xscale unconditionally
for those.
This should be safe to apply on all stable kernels, and will be required
in order to keep building them with gcc-11 and higher.
Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=996419
Reported-by: Antonio Terceiro <antonio.terceiro@linaro.org>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Reported-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Cc: Matthias Klose <doko@debian.org>
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d08e7bf0d upstream.
Currently __set_fixmap() bails out with a warning when called in early boot
from early_iounmap(). Fix it, and while at it, make the comment a bit easier
to understand.
Cc: <stable@vger.kernel.org>
Fixes: b089c31c51 ("ARM: 8667/3: Fix memory attribute inconsistencies when using fixmap")
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d336509cb9 ]
The below commit added optional support for passing a bind address.
It configures the sockaddr bind arguments before parsing options and
reconfigures on options -b and -4.
This broke support for passing port (-p) on its own.
Configure sockaddr after parsing all arguments.
Fixes: 3327a9c463 ("selftests: add functionals test for UDP GRO")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ca110bf8d ]
Ensure diagnostics monitoring support is implemented for the SFF 8472
compliant port module and set the correct length for ethtool port
module eeprom read.
Fixes: f56ec6766d ("cxgb4: Add support for ethtool i2c dump")
Signed-off-by: Manoj Malviya <manojmalviya@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5d5aadcf3 ]
We got the following WARNING when running ab/nginx
test with RDMA link flapping (up-down-up).
The reason is when smc_sock fallback and at linkdown
happens simultaneously, we may got the following situation:
__smc_lgr_terminate()
--> smc_conn_kill()
--> smc_close_active_abort()
smc_sock->sk_state = SMC_CLOSED
sock_put(smc_sock)
smc_sock was set to SMC_CLOSED and sock_put() been called
when terminate the link group. But later application call
close() on the socket, then we got:
__smc_release():
if (smc_sock->fallback)
smc_sock->sk_state = SMC_CLOSED
sock_put(smc_sock)
Again we set the smc_sock to CLOSED through it's already
in CLOSED state, and double put the refcnt, so the following
warning happens:
refcount_t: underflow; use-after-free.
WARNING: CPU: 5 PID: 860 at lib/refcount.c:28 refcount_warn_saturate+0x8d/0xf0
Modules linked in:
CPU: 5 PID: 860 Comm: nginx Not tainted 5.10.46+ #403
Hardware name: Alibaba Cloud Alibaba Cloud ECS, BIOS 8c24b4c 04/01/2014
RIP: 0010:refcount_warn_saturate+0x8d/0xf0
Code: 05 5c 1e b5 01 01 e8 52 25 bc ff 0f 0b c3 80 3d 4f 1e b5 01 00 75 ad 48
RSP: 0018:ffffc90000527e50 EFLAGS: 00010286
RAX: 0000000000000026 RBX: ffff8881300df2c0 RCX: 0000000000000027
RDX: 0000000000000000 RSI: ffff88813bd58040 RDI: ffff88813bd58048
RBP: 0000000000000000 R08: 0000000000000003 R09: 0000000000000001
R10: ffff8881300df2c0 R11: ffffc90000527c78 R12: ffff8881300df340
R13: ffff8881300df930 R14: ffff88810b3dad80 R15: ffff8881300df4f8
FS: 00007f739de8fb80(0000) GS:ffff88813bd40000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000000a01b008 CR3: 0000000111b64003 CR4: 00000000003706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
smc_release+0x353/0x3f0
__sock_release+0x3d/0xb0
sock_close+0x11/0x20
__fput+0x93/0x230
task_work_run+0x65/0xa0
exit_to_user_mode_prepare+0xf9/0x100
syscall_exit_to_user_mode+0x27/0x190
entry_SYSCALL_64_after_hwframe+0x44/0xa9
This patch adds check in __smc_release() to make
sure we won't do an extra sock_put() and set the
socket to CLOSED when its already in CLOSED state.
Fixes: 51f1de79ad (net/smc: replace sock_put worker by socket refcounting)
Signed-off-by: Dust Li <dust.li@linux.alibaba.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: Dust Li <dust.li@linux.alibaba.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7cd82b905 ]
Currently vosck_connect() increments sock refcount for nonblocking
socket each time it's called, which can lead to memory leak if
it's called multiple times because connect timeout function decrements
sock refcount only once.
Fixes it by making vsock_connect() return -EALREADY immediately when
sock state is already SS_CONNECTING.
Fixes: d021c34405 ("VSOCK: Introduce VM Sockets")
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Eiichi Tsukata <eiichi.tsukata@nutanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f64ab8e4f3 ]
Commit fe28c53ed7 ("net: stmmac: fix taprio configuration when
base_time is in the past") allowed some base time values in the past,
but apparently not all, the base-time value of 0 (Jan 1st 1970) is still
explicitly denied by the driver.
Remove the bogus check.
Fixes: b60189e039 ("net: stmmac: Integrate EST with TAPRIO scheduler API")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 688db0c7a4 ]
Currently, driver only allow configuring ETS bandwidth of TCs according
to the max TC number queried from firmware. However, the hardware actually
supports 8 TCs and users may need to configure ETS bandwidth of all TCs,
so remove the restriction.
Fixes: 330baff542 ("net: hns3: add ETS TC weight setting in SSU module")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c360cc1cc ]
The priv->ntfy_blocks[] has "priv->num_ntfy_blks" elements so this >
needs to be >= to prevent an off by one bug. The priv->ntfy_blocks[]
array is allocated in gve_alloc_notify_blocks().
Fixes: 87a7f321bb ("gve: Recover from queue stall due to missed IRQ")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0dc3b93bd ]
Strparser is reusing the qdisc_skb_cb struct to stash the skb message handling
progress, e.g. offset and length of the skb. First this is poorly named and
inherits a struct from qdisc that doesn't reflect the actual usage of cb[] at
this layer.
But, more importantly strparser is using the following to access its metadata.
(struct _strp_msg *)((void *)skb->cb + offsetof(struct qdisc_skb_cb, data))
Where _strp_msg is defined as:
struct _strp_msg {
struct strp_msg strp; /* 0 8 */
int accum_len; /* 8 4 */
/* size: 12, cachelines: 1, members: 2 */
/* last cacheline: 12 bytes */
};
So we use 12 bytes of ->data[] in struct. However in BPF code running parser
and verdict the user has read capabilities into the data[] array as well. Its
not too problematic, but we should not be exposing internal state to BPF
program. If its really needed then we can use the probe_read() APIs which allow
reading kernel memory. And I don't believe cb[] layer poses any API breakage by
moving this around because programs can't depend on cb[] across layers.
In order to fix another issue with a ctx rewrite we need to stash a temp
variable somewhere. To make this work cleanly this patch builds a cb struct
for sk_skb types called sk_skb_cb struct. Then we can use this consistently
in the strparser, sockmap space. Additionally we can start allowing ->cb[]
write access after this.
Fixes: 604326b41a ("bpf, sockmap: convert to generic sk_msg interface")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Jussi Maki <joamaki@gmail.com>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/20211103204736.248403-5-john.fastabend@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8b8315e39 ]
We do not need to handle unhash from BPF side we can simply wait for the
close to happen. The original concern was a socket could transition from
ESTABLISHED state to a new state while the BPF hook was still attached.
But, we convinced ourself this is no longer possible and we also improved
BPF sockmap to handle listen sockets so this is no longer a problem.
More importantly though there are cases where unhash is called when data is
in the receive queue. The BPF unhash logic will flush this data which is
wrong. To be correct it should keep the data in the receive queue and allow
a receiving application to continue reading the data. This may happen when
tcp_abort() is received for example. Instead of complicating the logic in
unhash simply moving all this to tcp_close() hook solves this.
Fixes: 51199405f9 ("bpf: skb_verdict, support SK_PASS on RX BPF path")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Jussi Maki <joamaki@gmail.com>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/20211103204736.248403-3-john.fastabend@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7c386fbc2 ]
gcc warns about undefined behavior the vmalloc code when building
with CONFIG_ARM64_PA_BITS_52, when the 'idx++' in the argument to
__phys_to_pte_val() is evaluated twice:
mm/vmalloc.c: In function 'vmap_pfn_apply':
mm/vmalloc.c:2800:58: error: operation on 'data->idx' may be undefined [-Werror=sequence-point]
2800 | *pte = pte_mkspecial(pfn_pte(data->pfns[data->idx++], data->prot));
| ~~~~~~~~~^~
arch/arm64/include/asm/pgtable-types.h:25:37: note: in definition of macro '__pte'
25 | #define __pte(x) ((pte_t) { (x) } )
| ^
arch/arm64/include/asm/pgtable.h:80:15: note: in expansion of macro '__phys_to_pte_val'
80 | __pte(__phys_to_pte_val((phys_addr_t)(pfn) << PAGE_SHIFT) | pgprot_val(prot))
| ^~~~~~~~~~~~~~~~~
mm/vmalloc.c:2800:30: note: in expansion of macro 'pfn_pte'
2800 | *pte = pte_mkspecial(pfn_pte(data->pfns[data->idx++], data->prot));
| ^~~~~~~
I have no idea why this never showed up earlier, but the safest
workaround appears to be changing those macros into inline functions
so the arguments get evaluated only once.
Cc: Matthew Wilcox <willy@infradead.org>
Fixes: 75387b9263 ("arm64: handle 52-bit physical addresses in page table entries")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211105075414.2553155-1-arnd@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9fec40f850 ]
skb is already freed by dev_kfree_skb in pn533_fill_fragment_skbs,
but follow error handler branch when pn533_fill_fragment_skbs()
fails, skb is freed again, results in double free issue. Fix this
by not free skb in error path of pn533_fill_fragment_skbs.
Fixes: 963a82e07d ("NFC: pn533: Split large Tx frames in chunks")
Fixes: 93ad42020c ("NFC: pn533: Target mode Tx fragmentation support")
Signed-off-by: Chengfeng Ye <cyeaa@connect.ust.hk>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ac9dfd58b ]
Both ifindex and LLC_SK_DEV_HASH_ENTRIES are signed.
This means that (ifindex % LLC_SK_DEV_HASH_ENTRIES) is negative
if @ifindex is negative.
We could simply make LLC_SK_DEV_HASH_ENTRIES unsigned.
In this patch I chose to use hash_32() to get more entropy
from @ifindex, like llc_sk_laddr_hashfn().
UBSAN: array-index-out-of-bounds in ./include/net/llc.h:75:26
index -43 is out of range for type 'hlist_head [64]'
CPU: 1 PID: 20999 Comm: syz-executor.3 Not tainted 5.15.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
ubsan_epilogue+0xb/0x5a lib/ubsan.c:151
__ubsan_handle_out_of_bounds.cold+0x62/0x6c lib/ubsan.c:291
llc_sk_dev_hash include/net/llc.h:75 [inline]
llc_sap_add_socket+0x49c/0x520 net/llc/llc_conn.c:697
llc_ui_bind+0x680/0xd70 net/llc/af_llc.c:404
__sys_bind+0x1e9/0x250 net/socket.c:1693
__do_sys_bind net/socket.c:1704 [inline]
__se_sys_bind net/socket.c:1702 [inline]
__x64_sys_bind+0x6f/0xb0 net/socket.c:1702
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7fa503407ae9
Fixes: 6d2e3ea284 ("llc: use a device based hash table to speed up multicast delivery")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit afe8605ca4 ]
There is one possible race window between zs_pool_dec_isolated() and
zs_unregister_migration() because wait_for_isolated_drain() checks the
isolated count without holding class->lock and there is no order inside
zs_pool_dec_isolated(). Thus the below race window could be possible:
zs_pool_dec_isolated zs_unregister_migration
check pool->destroying != 0
pool->destroying = true;
smp_mb();
wait_for_isolated_drain()
wait for pool->isolated_pages == 0
atomic_long_dec(&pool->isolated_pages);
atomic_long_read(&pool->isolated_pages) == 0
Since we observe the pool->destroying (false) before atomic_long_dec()
for pool->isolated_pages, waking pool->migration_wait up is missed.
Fix this by ensure checking pool->destroying happens after the
atomic_long_dec(&pool->isolated_pages).
Link: https://lkml.kernel.org/r/20210708115027.7557-1-linmiaohe@huawei.com
Fixes: 701d678599 ("mm/zsmalloc.c: fix race condition in zs_destroy_pool")
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Henry Burns <henryburns@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b93c6a911a ]
When I do fuzz test for bonding device interface, I got the following
use-after-free Calltrace:
==================================================================
BUG: KASAN: use-after-free in bond_enslave+0x1521/0x24f0
Read of size 8 at addr ffff88825bc11c00 by task ifenslave/7365
CPU: 5 PID: 7365 Comm: ifenslave Tainted: G E 5.15.0-rc1+ #13
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1 04/01/2014
Call Trace:
dump_stack_lvl+0x6c/0x8b
print_address_description.constprop.0+0x48/0x70
kasan_report.cold+0x82/0xdb
__asan_load8+0x69/0x90
bond_enslave+0x1521/0x24f0
bond_do_ioctl+0x3e0/0x450
dev_ifsioc+0x2ba/0x970
dev_ioctl+0x112/0x710
sock_do_ioctl+0x118/0x1b0
sock_ioctl+0x2e0/0x490
__x64_sys_ioctl+0x118/0x150
do_syscall_64+0x35/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f19159cf577
Code: b3 66 90 48 8b 05 11 89 2c 00 64 c7 00 26 00 00 00 48 c7 c0 ff ff ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 b8 10 00 00 00 0f 05 <48> 3d 01 f0 ff ff 78
RSP: 002b:00007ffeb3083c78 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 00007ffeb3084bca RCX: 00007f19159cf577
RDX: 00007ffeb3083ce0 RSI: 0000000000008990 RDI: 0000000000000003
RBP: 00007ffeb3084bc4 R08: 0000000000000040 R09: 0000000000000000
R10: 00007ffeb3084bc0 R11: 0000000000000246 R12: 00007ffeb3083ce0
R13: 0000000000000000 R14: 0000000000000000 R15: 00007ffeb3083cb0
Allocated by task 7365:
kasan_save_stack+0x23/0x50
__kasan_kmalloc+0x83/0xa0
kmem_cache_alloc_trace+0x22e/0x470
bond_enslave+0x2e1/0x24f0
bond_do_ioctl+0x3e0/0x450
dev_ifsioc+0x2ba/0x970
dev_ioctl+0x112/0x710
sock_do_ioctl+0x118/0x1b0
sock_ioctl+0x2e0/0x490
__x64_sys_ioctl+0x118/0x150
do_syscall_64+0x35/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
Freed by task 7365:
kasan_save_stack+0x23/0x50
kasan_set_track+0x20/0x30
kasan_set_free_info+0x24/0x40
__kasan_slab_free+0xf2/0x130
kfree+0xd1/0x5c0
slave_kobj_release+0x61/0x90
kobject_put+0x102/0x180
bond_sysfs_slave_add+0x7a/0xa0
bond_enslave+0x11b6/0x24f0
bond_do_ioctl+0x3e0/0x450
dev_ifsioc+0x2ba/0x970
dev_ioctl+0x112/0x710
sock_do_ioctl+0x118/0x1b0
sock_ioctl+0x2e0/0x490
__x64_sys_ioctl+0x118/0x150
do_syscall_64+0x35/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
Last potentially related work creation:
kasan_save_stack+0x23/0x50
kasan_record_aux_stack+0xb7/0xd0
insert_work+0x43/0x190
__queue_work+0x2e3/0x970
delayed_work_timer_fn+0x3e/0x50
call_timer_fn+0x148/0x470
run_timer_softirq+0x8a8/0xc50
__do_softirq+0x107/0x55f
Second to last potentially related work creation:
kasan_save_stack+0x23/0x50
kasan_record_aux_stack+0xb7/0xd0
insert_work+0x43/0x190
__queue_work+0x2e3/0x970
__queue_delayed_work+0x130/0x180
queue_delayed_work_on+0xa7/0xb0
bond_enslave+0xe25/0x24f0
bond_do_ioctl+0x3e0/0x450
dev_ifsioc+0x2ba/0x970
dev_ioctl+0x112/0x710
sock_do_ioctl+0x118/0x1b0
sock_ioctl+0x2e0/0x490
__x64_sys_ioctl+0x118/0x150
do_syscall_64+0x35/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
The buggy address belongs to the object at ffff88825bc11c00
which belongs to the cache kmalloc-1k of size 1024
The buggy address is located 0 bytes inside of
1024-byte region [ffff88825bc11c00, ffff88825bc12000)
The buggy address belongs to the page:
page:ffffea00096f0400 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x25bc10
head:ffffea00096f0400 order:3 compound_mapcount:0 compound_pincount:0
flags: 0x57ff00000010200(slab|head|node=1|zone=2|lastcpupid=0x7ff)
raw: 057ff00000010200 ffffea0009a71c08 ffff888240001968 ffff88810004dbc0
raw: 0000000000000000 00000000000a000a 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff88825bc11b00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff88825bc11b80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff88825bc11c00: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff88825bc11c80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff88825bc11d00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================
Put new_slave in bond_sysfs_slave_add() will cause use-after-free problems
when new_slave is accessed in the subsequent error handling process. Since
new_slave will be put in the subsequent error handling process, remove the
unnecessary put to fix it.
In addition, when sysfs_create_file() fails, if some files have been crea-
ted successfully, we need to call sysfs_remove_file() to remove them.
Since there are sysfs_create_files() & sysfs_remove_files() can be used,
use these two functions instead.
Fixes: 7afcaec496 (bonding: use kobject_put instead of _del after kobject_add)
Signed-off-by: Huang Guobin <huangguobin4@huawei.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 009a789443 ]
The handling of PMIC register reads through writing 0 to address 4
of the OpRegion is wrong. Instead of returning the read value
through the value64, which is a no-op for function == ACPI_WRITE calls,
store the value and then on a subsequent function == ACPI_READ with
address == 3 (the address for the value field of the OpRegion)
return the stored value.
This has been tested on a Xiaomi Mi Pad 2 and makes the ACPI battery dev
there mostly functional (unfortunately there are still other issues).
Here are the SET() / GET() functions of the PMIC ACPI device,
which use this OpRegion, which clearly show the new behavior to
be correct:
OperationRegion (REGS, 0x8F, Zero, 0x50)
Field (REGS, ByteAcc, NoLock, Preserve)
{
CLNT, 8,
SA, 8,
OFF, 8,
VAL, 8,
RWM, 8
}
Method (GET, 3, Serialized)
{
If ((AVBE == One))
{
CLNT = Arg0
SA = Arg1
OFF = Arg2
RWM = Zero
If ((AVBG == One))
{
GPRW = Zero
}
}
Return (VAL) /* \_SB_.PCI0.I2C7.PMI5.VAL_ */
}
Method (SET, 4, Serialized)
{
If ((AVBE == One))
{
CLNT = Arg0
SA = Arg1
OFF = Arg2
VAL = Arg3
RWM = One
If ((AVBG == One))
{
GPRW = One
}
}
}
Fixes: 0afa877a56 ("ACPI / PMIC: intel: add REGS operation region support")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b385cca473 ]
When a VF is removed and/or reset its Tx queues need to be
stopped from the PF. This is done by calling the ice_dis_vf_qs()
function, which calls ice_vsi_stop_lan_tx_rings(). Currently
ice_dis_vf_qs() is protected by the VF state bit ICE_VF_STATE_QS_ENA.
Unfortunately, this is causing the Tx queues to not be disabled in some
cases and when the VF tries to re-enable/reconfigure its Tx queues over
virtchnl the op is failing. This is because a VF can be reset and/or
removed before the ICE_VF_STATE_QS_ENA bit is set, but the Tx queues
were already configured via ice_vsi_cfg_single_txq() in the
VIRTCHNL_OP_CONFIG_VSI_QUEUES op. However, the ICE_VF_STATE_QS_ENA bit
is set on a successful VIRTCHNL_OP_ENABLE_QUEUES, which will always
happen after the VIRTCHNL_OP_CONFIG_VSI_QUEUES op.
This was causing the following error message when loading the ice
driver, creating VFs, and modifying VF trust in an endless loop:
[35274.192484] ice 0000:88:00.0: Failed to set LAN Tx queue context, error: ICE_ERR_PARAM
[35274.193074] ice 0000:88:00.0: VF 0 failed opcode 6, retval: -5
[35274.193640] iavf 0000:88:01.0: PF returned error -5 (IAVF_ERR_PARAM) to our request 6
Fix this by always calling ice_dis_vf_qs() and silencing the error
message in ice_vsi_stop_tx_ring() since the calling code ignores the
return anyway. Also, all other places that call ice_vsi_stop_tx_ring()
catch the error, so this doesn't affect those flows since there was no
change to the values the function returns.
Other solutions were considered (i.e. tracking which VF queues had been
"started/configured" in VIRTCHNL_OP_CONFIG_VSI_QUEUES, but it seemed
more complicated than it was worth. This solution also brings in the
chance for other unexpected conditions due to invalid state bit checks.
So, the proposed solution seemed like the best option since there is no
harm in failing to stop Tx queues that were never started.
This issue can be seen using the following commands:
for i in {0..50}; do
rmmod ice
modprobe ice
sleep 1
echo 1 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 1 > /sys/class/net/ens785f1/device/sriov_numvfs
ip link set ens785f1 vf 0 trust on
ip link set ens785f0 vf 0 trust on
sleep 2
echo 0 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 0 > /sys/class/net/ens785f1/device/sriov_numvfs
sleep 1
echo 1 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 1 > /sys/class/net/ens785f1/device/sriov_numvfs
ip link set ens785f1 vf 0 trust on
ip link set ens785f0 vf 0 trust on
done
Fixes: 77ca27c417 ("ice: add support for virtchnl_queue_select.[tx|rx]_queues bitmap")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce572a5b88 ]
VF was not able to change its hardware MAC address in case
the new address was already present in the MAC filter list.
Change the handling of VF add mac request to not return
if requested MAC address is already present on the list
and check if its hardware MAC needs to be updated in this case.
Fixes: ed4c068d46 ("ice: Enable ip link show on the PF to display VF unicast MAC(s)")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 563bcbae3b ]
The real_dev of a vlan net_device may be freed after
unregister_vlan_dev(). Access the real_dev continually by
vlan_dev_real_dev() will trigger the UAF problem for the
real_dev like following:
==================================================================
BUG: KASAN: use-after-free in vlan_dev_real_dev+0xf9/0x120
Call Trace:
kasan_report.cold+0x83/0xdf
vlan_dev_real_dev+0xf9/0x120
is_eth_port_of_netdev_filter.part.0+0xb1/0x2c0
is_eth_port_of_netdev_filter+0x28/0x40
ib_enum_roce_netdev+0x1a3/0x300
ib_enum_all_roce_netdevs+0xc7/0x140
netdevice_event_work_handler+0x9d/0x210
...
Freed by task 9288:
kasan_save_stack+0x1b/0x40
kasan_set_track+0x1c/0x30
kasan_set_free_info+0x20/0x30
__kasan_slab_free+0xfc/0x130
slab_free_freelist_hook+0xdd/0x240
kfree+0xe4/0x690
kvfree+0x42/0x50
device_release+0x9f/0x240
kobject_put+0x1c8/0x530
put_device+0x1b/0x30
free_netdev+0x370/0x540
ppp_destroy_interface+0x313/0x3d0
...
Move the put_device(real_dev) to vlan_dev_free(). Ensure
real_dev not be freed before vlan_dev unregistered.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: syzbot+e4df4e1389e28972e955@syzkaller.appspotmail.com
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27dff9a9c2 ]
Throughout the OpenRISC kernel port VMA is passed as NULL when flushing
kernel tlb entries. Somehow this was missed when I was testing
c28b27416d ("openrisc: Implement proper SMP tlb flushing") and now the
SMP kernel fails to completely boot.
In OpenRISC VMA is used only to determine which cores need to have their
TLB entries flushed.
This patch updates the logic to flush tlbs on all cores when the VMA is
passed as NULL. Also, we update places VMA is passed as NULL to use
flush_tlb_kernel_range instead. Now, the only place VMA is passed as
NULL is in the implementation of flush_tlb_kernel_range.
Fixes: c28b27416d ("openrisc: Implement proper SMP tlb flushing")
Reported-by: Jan Henrik Weinstock <jan.weinstock@rwth-aachen.de>
Signed-off-by: Stafford Horne <shorne@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1aabe578dd ]
ETHTOOL_A_PAUSE_STAT_MAX is the MAX attribute id,
so we need to subtract non-stats and add one to
get a count (IOW -2+1 == -1).
Otherwise we'll see:
ethnl cmd 21: calculated reply length 40, but consumed 52
Fixes: 9a27a33027 ("ethtool: add standard pause stats")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d52bcb47bd ]
This patch allows to use 0 for `coal->rx_coalesce_usecs` param to
disable rx irq coalescing.
Previously we could enable rx irq coalescing via ethtool
(For ex: `ethtool -C eth0 rx-usecs 2000`) but we couldn't disable
it because this part rejects 0 value:
if (!coal->rx_coalesce_usecs)
return -EINVAL;
Fixes: 84da2658a6 ("TI DaVinci EMAC : Implement interrupt pacing functionality.")
Signed-off-by: Maxim Kiselev <bigunclemax@gmail.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20211101152343.4193233-1-bigunclemax@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f98960c04 ]
A successful 'clk_prepare()' call should be balanced by a corresponding
'clk_unprepare()' call in the error handling path of the probe, as already
done in the remove function.
More specifically, 'clk_prepare_enable()' is used, but 'clk_disable()' is
also already called. So just the unprepare step has still to be done.
Update the error handling path accordingly.
Fixes: 75d31c2372 ("i2c: xlr: add support for Sigma Designs controller variant")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 01d29f87fc ]
If we already hold open state on the client, yet the server gives us a
completely different stateid to the one we already hold, then we
currently treat it as if it were an out-of-sequence update, and wait for
5 seconds for other updates to come in.
This commit fixes the behaviour so that we immediately start processing
of the new stateid, and then leave it to the call to
nfs4_test_and_free_stateid() to decide what to do with the old stateid.
Fixes: b4868b44c5 ("NFSv4: Wait for stateid updates after CLOSE/OPEN_DOWNGRADE")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28b7ee33a2 ]
TI AR7 Watchdog Timer is only build for 32bit.
Avoid error like:
In file included from drivers/watchdog/ar7_wdt.c:29:
./arch/mips/include/asm/mach-ar7/ar7.h: In function ‘ar7_is_titan’:
./arch/mips/include/asm/mach-ar7/ar7.h:111:24: error: implicit declaration of function ‘KSEG1ADDR’; did you mean ‘CKSEG1ADDR’? [-Werror=implicit-function-declaration]
111 | return (readl((void *)KSEG1ADDR(AR7_REGS_GPIO + 0x24)) & 0xffff) ==
| ^~~~~~~~~
| CKSEG1ADDR
Fixes: da2a68b3eb ("watchdog: Enable COMPILE_TEST where possible")
Signed-off-by: Jackie Liu <liuyun01@kylinos.cn>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210907024904.4127611-1-liu.yun@linux.dev
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1aaa557b2d ]
'make randconfig' can produce a .config file with
"CONFIG_MEMORY_RESERVE=" (no value) since it has no default.
When a subsequent 'make all' is done, kconfig restarts the config
and prompts for a value for MEMORY_RESERVE. This breaks
scripting/automation where there is no interactive user input.
Add a default value for MEMORY_RESERVE. (Any integer value will
work here for kconfig.)
Fixes a kconfig warning:
.config:214:warning: symbol value '' invalid for MEMORY_RESERVE
* Restart config...
Memory reservation (MiB) (MEMORY_RESERVE) [] (NEW)
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2") # from beginning of git history
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: linux-m68k@lists.linux-m68k.org
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce0ee4e6ac ]
Today the sh code allocates memory the first time a process uses
the fpu. If that memory allocation fails, kill the affected task
with force_sig(SIGKILL) rather than do_group_exit(SIGKILL).
Calling do_group_exit from an exception handler can potentially lead
to dead locks as do_group_exit is not designed to be called from
interrupt context. Instead use force_sig(SIGKILL) to kill the
userspace process. Sending signals in general and force_sig in
particular has been tested from interrupt context so there should be
no problems.
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: linux-sh@vger.kernel.org
Fixes: 0ea820cf9b ("sh: Move over to dynamically allocated FPU context.")
Link: https://lkml.kernel.org/r/20211020174406.17889-6-ebiederm@xmission.com
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e7e1e880b1 ]
Before the `callback_result` callback was introduced drivers coded their
invocation to the callback in a similar way to:
if (cb->callback) {
spin_unlock(&dma->lock);
cb->callback(cb->callback_param);
spin_lock(&dma->lock);
}
With the introduction of `callback_result` two helpers where introduced to
transparently handle both types of callbacks. And drivers where updated to
look like this:
if (dmaengine_desc_callback_valid(cb)) {
spin_unlock(&dma->lock);
dmaengine_desc_callback_invoke(cb, ...);
spin_lock(&dma->lock);
}
dmaengine_desc_callback_invoke() correctly handles both `callback_result`
and `callback`. But we forgot to update the dmaengine_desc_callback_valid()
function to check for `callback_result`. As a result DMA descriptors that
use the `callback_result` rather than `callback` don't have their callback
invoked by drivers that follow the pattern above.
Fix this by checking for both `callback` and `callback_result` in
dmaengine_desc_callback_valid().
Fixes: f067025bc6 ("dmaengine: add support to provide error result from a DMA transation")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20211023134101.28042-1-lars@metafoo.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5648b5e116 ]
On 64bit platforms the MAC header is set to 0xffff on allocation and
also when a helper like skb_unset_mac_header() is called.
dev_parse_header may call skb_mac_header() which assumes valid mac offset:
BUG: KASAN: use-after-free in eth_header_parse+0x75/0x90
Read of size 6 at addr ffff8881075a5c05 by task nf-queue/1364
Call Trace:
memcpy+0x20/0x60
eth_header_parse+0x75/0x90
__nfqnl_enqueue_packet+0x1a61/0x3380
__nf_queue+0x597/0x1300
nf_queue+0xf/0x40
nf_hook_slow+0xed/0x190
nf_hook+0x184/0x440
ip_output+0x1c0/0x2a0
nf_reinject+0x26f/0x700
nfqnl_recv_verdict+0xa16/0x18b0
nfnetlink_rcv_msg+0x506/0xe70
The existing code only works if the skb has a mac header.
Fixes: 2c38de4c1f ("netfilter: fix looped (broad|multi)cast's MAC handling")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8120bd469f ]
Free the kbuf buffer before returning from the dpaa2_console_read()
function. The variable no longer goes out of scope, leaking the storage
it points to.
Fixes: c93349d8c1 ("soc: fsl: add DPAA2 console support")
Signed-off-by: Robert-Ionut Alexa <robert-ionut.alexa@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 840fe25833 ]
As the ht16k33 frame buffer sub-driver does not register an
fb_ops.fb_blank() handler, blanking does not work:
$ echo 1 > /sys/class/graphics/fb0/blank
sh: write error: Invalid argument
Fix this by providing a handler that always returns zero, to make sure
blank events will be sent to the actual device handling the backlight.
Reported-by: Robin van der Gracht <robin@protonic.nl>
Suggested-by: Robin van der Gracht <robin@protonic.nl>
Fixes: 8992da44c6 ("auxdisplay: ht16k33: Driver for LED controller")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 80f9eb70fd ]
Currently /sys/class/graphics/fb0/bl_curve is not accessible (-ENODEV),
as the driver does not connect the backlight to the frame buffer device.
Fix this moving backlight initialization up, and filling in
fb_info.bl_dev.
Fixes: 8992da44c6 ("auxdisplay: ht16k33: Driver for LED controller")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit afcb5a811f ]
While writing an empty string to a device attribute is a no-op, and thus
does not need explicit safeguards, the user can still write a single
newline to an attribute file:
echo > .../message
If that happens, img_ascii_lcd_display() trims the newline, yielding an
empty string, and causing an infinite loop in img_ascii_lcd_scroll().
Fix this by adding a check for empty strings. Clear the display in case
one is encountered.
Fixes: 0cad855fbd ("auxdisplay: img-ascii-lcd: driver for simple ASCII LCD displays")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 133a48abf6 ]
If O_DIRECT bumps the commit_info rpcs_out field, then that could lead
to fsync() hangs. The fix is to ensure that O_DIRECT calls
nfs_commit_end().
Fixes: 723c921e7d ("sched/wait, fs/nfs: Convert wait_on_atomic_t() usage to the new wait_var_event() API")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4caab28a62 ]
The condition register PCI_RCV_INTX is used in irq_mask() and irq_unmask()
callbacks. Accesses to register can occur at the same time without a lock.
Add a lock into each callback to prevent the issue.
And INTX mask and unmask fields in PCL_RCV_INTX register should only be
set/reset for each bit. Clearing by PCL_RCV_INTX_ALL_MASK should be
removed.
INTX status fields in PCL_RCV_INTX register only indicates each INTX
interrupt status, so the handler can't clear by writing 1 to the field.
The status is expected to be cleared by the interrupt origin.
The ack function has no meaning, so should remove it.
Suggested-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/1631924579-24567-1-git-send-email-hayashi.kunihiko@socionext.com
Fixes: 7e6d5cd88a ("PCI: uniphier: Add UniPhier PCIe host controller support")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Pali Rohár <pali@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78e4d34218 ]
hisi_spi_nor_probe() invokes clk_disable_unprepare() on all paths after
successful call of clk_prepare_enable(). Besides, the clock is enabled by
hispi_spi_nor_prep() and disabled by hispi_spi_nor_unprep(). So at remove
time it is not possible to have the clock enabled. The patch removes
excessive clk_disable_unprepare() from hisi_spi_nor_remove().
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: e523f11141 ("mtd: spi-nor: add hisilicon spi-nor flash controller driver")
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20210709144529.31379-1-novikov@ispras.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c2b46c824 ]
When op_alloc() returns NULL to new_op, no error return code of
orangefs_revalidate_lookup() is assigned.
To fix this bug, ret is assigned with -ENOMEM in this case.
Fixes: 8bb8aefd5a ("OrangeFS: Change almost all instances of the string PVFS2 to OrangeFS.")
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64a93dbf25 ]
Partially revert commit 2ce209c42c ("NFS: Wait for requests that are
locked on the commit list"), since it can lead to deadlocks between
commit requests and nfs_join_page_group().
For now we should assume that any locked requests on the commit list are
either about to be removed and committed by another task, or the writes
they describe are about to be retransmitted. In either case, we should
not need to worry.
Fixes: 2ce209c42c ("NFS: Wait for requests that are locked on the commit list")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27ff8187f1 ]
Fix sparse warning:
drivers/opp/of.c:924 _opp_add_static_v2() warn: passing zero to 'ERR_PTR'
For duplicate OPPs 'ret' be set to zero.
Fixes: deac8703da ("PM / OPP: _of_add_opp_table_v2(): increment count only if OPP is added")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d419052bc6 ]
Commit 43f5c77bcb ("PCI: aardvark: Fix reporting CRS value") started
using CRSSVE flag for handling CRS responses.
PCI_EXP_RTCTL_CRSSVE flag is stored only in emulated config space buffer
and there is handler for PCI_EXP_RTCTL register. So every read operation
from config space automatically clears CRSSVE flag as it is not defined in
PCI_EXP_RTCTL read handler.
Fix this by reading current CRSSVE bit flag from emulated space buffer and
appending it to PCI_EXP_RTCTL read response.
Link: https://lore.kernel.org/r/20211005180952.6812-5-kabel@kernel.org
Fixes: 43f5c77bcb ("PCI: aardvark: Fix reporting CRS value")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7be28bd73f ]
drivers/gpu/drm/drm_plane_helper.c: In function 'drm_primary_helper_update':
drivers/gpu/drm/drm_plane_helper.c:113:32: error: 'visible' is used uninitialized [-Werror=uninitialized]
113 | struct drm_plane_state plane_state = {
| ^~~~~~~~~~~
drivers/gpu/drm/drm_plane_helper.c:178:14: note: 'visible' was declared here
178 | bool visible;
| ^~~~~~~
cc1: all warnings being treated as errors
visible is an output, not an input. in practice this use might turn out
OK but it's still UB.
Fixes: df86af9133 ("drm/plane-helper: Add drm_plane_helper_check_state()")
Reviewed-by: Simon Ser <contact@emersion.fr>
Signed-off-by: Alex Xu (Hello71) <alex_y_xu@yahoo.ca>
Signed-off-by: Simon Ser <contact@emersion.fr>
Link: https://patchwork.freedesktop.org/patch/msgid/20211007063706.305984-1-alex_y_xu@yahoo.ca
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2915fa062 ]
_nfs4_pnfs_v3/v4_ds_connect do
some work
smp_wmb
ds->ds_clp = clp;
And nfs4_ff_layout_prepare_ds currently does
smp_rmb
if(ds->ds_clp)
...
This patch places the smp_rmb after the if. This ensures that following
reads only happen once nfs4_ff_layout_prepare_ds has checked that data
has been properly initialized.
Fixes: d67ae825a5 ("pnfs/flexfiles: Add the FlexFile Layout Driver")
Signed-off-by: Baptiste Lepers <baptiste.lepers@gmail.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cec08f452a ]
If the directory changed while we were revalidating the dentry, then
don't update the dentry verifier. There is no value in setting the
verifier to an older value, and we could end up overwriting a more up to
date verifier from a parallel revalidation.
Fixes: efeda80da3 ("NFSv4: Fix revalidation of dentries with delegations")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Tested-by: Benjamin Coddington <bcodding@redhat.com>
Reviewed-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8228aea5a ]
The reason for the modification here is that the previous
offset information is incorrect, OFFSET_DEBUGSTAT = 0xE4 is
the correct value.
Fixes: 25708278f8 ("i2c: mediatek: Add i2c support for MediaTek MT8183")
Signed-off-by: Kewei Xu <kewei.xu@mediatek.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b6e27d01a ]
Dan Carpenter says:
The patch d20c11d86d: "nfsd: Protect session creation and client
confirm using client_lock" from Jul 30, 2014, leads to the following
Smatch static checker warning:
net/sunrpc/addr.c:178 rpc_parse_scope_id()
warn: sleeping in atomic context
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: d20c11d86d ("nfsd: Protect session creation and client...")
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d108370c64 ]
clang static analysis reports this representative problem:
label.c:1463:16: warning: Assigned value is garbage or undefined
label->hname = name;
^ ~~~~
In aa_update_label_name(), this the problem block of code
if (aa_label_acntsxprint(&name, ...) == -1)
return res;
On failure, aa_label_acntsxprint() has a more complicated return
that just -1. So check for a negative return.
It was also noted that the aa_label_acntsxprint() main comment refers
to a nonexistent parameter, so clean up the comment.
Fixes: f1bd904175 ("apparmor: add the base fns() for domain labels")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: John Johansen <john.johansen@canonical.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdf10ffe8f ]
When registering the IRQ handler fails, do not just return the error code,
this will free the devm_kzalloc()-ed data struct while leaving the queued
work queued and the registered power_supply registered with both of them
now pointing to free-ed memory, resulting in various kernel crashes
soon afterwards.
Instead properly tear-down things on IRQ handler register errors.
Fixes: 703df6c097 ("power: bq27xxx_battery: Reorganize I2C into a module")
Cc: Andrew F. Davis <afd@ti.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 18b8f5b6fc ]
mips_cm_error_report() extracts the cause and other cause from the error
register using shifts. This works fine for the former, as it is stored
in the top bits, and the shift will thus remove all non-related bits.
However, the latter is stored in the bottom bits, hence thus needs masking
to get rid of non-related bits. Without such masking, using it as an
index into the cm2_causes[] array will lead to an out-of-bounds access,
probably causing a crash.
Fix this by using FIELD_GET() instead. Bite the bullet and convert all
MIPS CM handling to the bitfield API, to improve readability and safety.
Fixes: 3885c2b463 ("MIPS: CM: Add support for reporting CM cache errors")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 778a0cbef5 ]
The setting from the cirrus,ts-inv property should be applied to the
TIP_SENSE_INV bit, as this is the one that actually affects the jack
detect block. The TS_INV bit only swaps the meaning of the PLUG and
UNPLUG interrupts and should always be 1 for the interrupts to have
the normal meaning.
Due to some misunderstanding the driver had been implemented to
configure the TS_INV bit based on the jack switch polarity. This made
the interrupts behave the correct way around, but left the jack detect
block, button detect and analogue circuits always interpreting an open
switch as unplugged.
The signal chain inside the codec is:
SENSE pin -> TIP_SENSE_INV -> TS_INV -> (invert) -> interrupts
|
v
Jack detect,
button detect and
analog control
As the TIP_SENSE_INV already performs the necessary inversion the
TS_INV bit never needs to change. It must always be 1 to yield the
expected interrupt behaviour.
Some extra confusion has arisen because of the additional invert in the
interrupt path, meaning that a value applied to the TS_INV bit produces
the opposite effect of applying it to the TIP_SENSE_INV bit. The ts-inv
property has therefore always had the opposite effect to what might be
expected (0 = inverted, 1 = not inverted). To maintain the meaning of
the ts-inv property it must be inverted when applied to TIP_SENSE_INV.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2c394ca796 ("ASoC: Add support for CS42L42 codec")
Link: https://lore.kernel.org/r/20211028140902.11786-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43775e62c4 ]
The wait_for_completion_timeout function returns 0 if timed out or a
positive value if completed. Hence, "less than zero" comparison always
misses timeouts and doesn't kill the URB as it should, leading to
re-sending it while it is active.
Fixes: 42337b9d4d ("HID: add driver for U2F Zero built-in LED and RNG")
Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7abf78b7a ]
The previous commit fixed handling of incomplete packets but broke error
handling: offsetof returns an unsigned value (size_t), but when compared
against the signed return value, the return value is interpreted as if
it were unsigned, so negative return values are never less than the
offset.
To make the code easier to read, calculate the minimal packet length
once and separately, and assign it to a signed int variable to eliminate
unsigned math and the need for type casts. It then becomes immediately
obvious how the actual data length is calculated and why the return
value cannot be less than the minimal length.
Fixes: 22d65765f2 ("HID: u2fzero: ignore incomplete packets without data")
Fixes: 42337b9d4d ("HID: add driver for U2F Zero built-in LED and RNG")
Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 88b20f84f0 ]
xilinx_uartps .start_tx() clears TXEMPTY when enabling TXEMPTY to avoid
any previous TXEVENT event asserting the UART interrupt. This clear
operation is done immediately after filling the TX FIFO.
However, if the bytes inserted by cdns_uart_handle_tx() are consumed by
the UART before the TXEMPTY is cleared, the clear operation eats the new
TXEMPTY event as well, causing cdns_uart_isr() to never receive the
TXEMPTY event. If there are bytes still queued in circbuf, TX will get
stuck as they will never get transferred to FIFO (unless new bytes are
queued to circbuf in which case .start_tx() is called again).
While the racy missed TXEMPTY occurs fairly often with short data
sequences (e.g. write 1 byte), in those cases circbuf is usually empty
so no action on TXEMPTY would have been needed anyway. On the other
hand, longer data sequences make the race much more unlikely as UART
takes longer to consume the TX FIFO. Therefore it is rare for this race
to cause visible issues in general.
Fix the race by clearing the TXEMPTY bit in ISR *before* filling the
FIFO.
The TXEMPTY bit in ISR will only get asserted at the exact moment the
TX FIFO *becomes* empty, so clearing the bit before filling FIFO does
not cause an extra immediate assertion even if the FIFO is initially
empty.
This is hard to reproduce directly on a normal system, but inserting
e.g. udelay(200) after cdns_uart_handle_tx(port), setting 4000000 baud,
and then running "dd if=/dev/zero bs=128 of=/dev/ttyPS0 count=50"
reliably reproduces the issue on my ZynqMP test system unless this fix
is applied.
Fixes: 85baf542d5 ("tty: xuartps: support 64 byte FIFO size")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Link: https://lore.kernel.org/r/20211026102741.2910441-1-anssi.hannula@bitwise.fi
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b475bf0ec4 ]
The FSEL_MASK which selects the refclock is defined incorrectly.
It should be [4:6] not [5:7]. Due to this incorrect definition, the BIT(7)
in USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON0 is reset which keeps PHY analog
blocks ON during suspend.
Fix this issue by correctly defining the FSEL_MASK.
Fixes: 51e8114f80 ("phy: qcom-snps: Add SNPS USB PHY driver for QCOM based SOCs")
Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
Link: https://lore.kernel.org/r/1635135575-5668-1-git-send-email-quic_c_sanm@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d387f61b0 ]
In case of USB_DR_MODE_PERIPHERAL, the OTG clock is disabled at the end of
the probe (it is not the case if USB_DR_MODE_HOST or USB_DR_MODE_OTG).
The clock is then enabled on udc_start.
If dwc2_drd_role_sw_set is called before udc_start (it is the case if the
usb cable is plugged at boot), GOTGCTL and GUSBCFG registers cannot be
read/written, so session cannot be overridden.
To avoid this case, check the ll_hw_enabled value and enable the clock if
it is available, and disable it after the override.
Fixes: 17f934024e ("usb: dwc2: override PHY input signals with usb role switch support")
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211005095305.66397-3-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2cab2a24f ]
Instead of forcing the role to Device, check the dr_mode configuration.
If the core is Host only, force the mode to Host, this to avoid the
dwc2_force_mode warning:
WARNING: CPU: 1 PID: 21 at drivers/usb/dwc2/core.c:615 dwc2_drd_init+0x104/0x17c
When forcing mode to Host, dwc2_force_mode may sleep the time the host
role is applied. To avoid sleeping while atomic context, move the call
to dwc2_force_mode after spin_unlock_irqrestore. It is safe, as
interrupts are not yet unmasked here.
Fixes: 17f934024e ("usb: dwc2: override PHY input signals with usb role switch support")
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211005095305.66397-2-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b600bd7eb3 ]
With commit ecb010d441 ("iio: imu: adis: Refactor adis_initial_startup")
we are doing a HW or SW reset to the device which means that we'll get
the default state of the data ready pin (which is enabled). Hence there's
no point in disabling the IRQ in the init function. Moreover, this
function is intended to initialize internal data structures and not
really do anything on the device.
As a result of this, some devices were left with the data ready pin enabled
after probe which was not the desired behavior. Thus, we move the call to
'adis_enable_irq()' to the initial startup function where it makes more
sense for it to be.
Note that for devices that cannot mask/unmask the pin, it makes no sense
to call the function at this point since the IRQ should not have been
yet requested. This will be improved in a follow up change.
Fixes: ecb010d441 ("iio: imu: adis: Refactor adis_initial_startup")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210903141423.517028-2-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3e56c050a ]
The general expectation is that powering on a power-domain should make
the power domain deliver some power, and if a specific performance state
is needed further requests has to be made.
But in contrast with other power-domain implementations (e.g. rpmpd) the
RPMh does not have an interface to enable the power, so the driver has
to vote for a particular corner (performance level) in rpmh_power_on().
But the corner is never initialized, so a typical request to simply
enable the power domain would not actually turn on the hardware. Further
more, when no more clients vote for a performance state (i.e. the
aggregated vote is 0) the power domain would be turned off.
Fix both of these issues by always voting for a corner with non-zero
value, when the power domain is enabled.
The tracking of the lowest non-zero corner is performed to handle the
corner case if there's ever a domain with a non-zero lowest corner, in
which case both rpmh_power_on() and rpmh_rpmhpd_set_performance_state()
would be allowed to use this lowest corner.
Fixes: 279b7e8a62 ("soc: qcom: rpmhpd: Add RPMh power domain driver")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20211005033732.2284447-1-bjorn.andersson@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f87a74d31 ]
The STM32 SAI subblocks registers offsets are in the range
0x0004 (SAIx_CR1) to 0x0020 (SAIx_DR).
The corresponding range length is 0x20 instead of 0x1c.
Change reg property accordingly.
Fixes: 5afd65c3a0 ("ARM: dts: stm32: add sai support on stm32mp157c")
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2012579b31 ]
The SPI NOR is a bit further away from the SoC on DHCOR than on DHCOM,
which causes additional signal delay. At 108 MHz, this delay triggers
a sporadic issue where the first bit of RX data is not received by the
QSPI controller.
There are two options of addressing this problem, either by using the
DLYB block to compensate the extra delay, or by reducing the QSPI bus
clock frequency. The former requires calibration and that is overly
complex, so opt for the second option.
Fixes: 76045bc457 ("ARM: dts: stm32: Add QSPI NOR on AV96")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ab1891640 ]
Commit 723de0f917 ("staging: most: remove device from interface
structure") moved registration of driver-provided struct device to
the most subsystem.
Dim2 used to register the same struct device to provide a custom device
attribute. This causes double-registration of the same struct device.
Fix that by moving the custom attribute to driver's dev_groups.
This moves attribute to the platform_device object, which is a better
location for platform-specific attributes anyway.
Fixes: 723de0f917 ("staging: most: remove device from interface structure")
Acked-by: Christian Gromm <christian.gromm@microchip.com>
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Link: https://lore.kernel.org/r/20211011061117.21435-1-nikita.yoush@cogentembedded.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4875d509a ]
This variable is just a temporary variable, used to do an endian
conversion. The problem is that the last byte is not initialized. After
the conversion is completely done, the last byte is discarded so it doesn't
cause a problem. But static checkers and the KMSan runtime checker can
detect the uninitialized read and will complain about it.
Link: https://lore.kernel.org/r/20211006073242.GA8404@kili
Fixes: 5036f0a0ec ("[SCSI] csiostor: Fix sparse warnings.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9583922563 ]
Commit a21d1becaa ("powerpc: Reintroduce is_kvm_guest() as a fast-path
check") added is_kvm_guest() and changed kvm_para_available() to use it.
is_kvm_guest() checks a static key, kvm_guest, and that static key is
set in check_kvm_guest().
The problem is check_kvm_guest() is only called on pseries, and even
then only in some configurations. That means is_kvm_guest() always
returns false on all non-pseries and some pseries depending on
configuration. That's a bug.
For PR KVM guests this is noticable because they no longer do live
patching of themselves, which can be detected by the omission of a
message in dmesg such as:
KVM: Live patching for a fast VM worked
To fix it make check_kvm_guest() an initcall, to ensure it's always
called at boot. It needs to be core so that it runs before
kvm_guest_init() which is postcore. To be an initcall it needs to return
int, where 0 means success, so update that.
We still call it manually in pSeries_smp_probe(), because that runs
before init calls are run.
Fixes: a21d1becaa ("powerpc: Reintroduce is_kvm_guest() as a fast-path check")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210623130514.2543232-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2719b26ae ]
While investigating a lockup at startup on Powerbook 3400C, it was
identified that the fbdev driver generates alignment exception at
startup:
--- interrupt: 600 at memset+0x60/0xc0
NIP: c0021414 LR: c03fc49c CTR: 00007fff
REGS: ca021c10 TRAP: 0600 Tainted: G W (5.14.2-pmac-00727-g12a41fa69492)
MSR: 00009032 <EE,ME,IR,DR,RI> CR: 44008442 XER: 20000100
DAR: cab80020 DSISR: 00017c07
GPR00: 00000007 ca021cd0 c14412e0 cab80000 00000000 00100000 cab8001c 00000004
GPR08: 00100000 00007fff 00000000 00000000 84008442 00000000 c0006fb4 00000000
GPR16: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00100000
GPR24: 00000000 81800000 00000320 c15fa400 c14d1878 00000000 c14d1800 c094e19c
NIP [c0021414] memset+0x60/0xc0
LR [c03fc49c] chipsfb_pci_init+0x160/0x580
--- interrupt: 600
[ca021cd0] [c03fc46c] chipsfb_pci_init+0x130/0x580 (unreliable)
[ca021d20] [c03a3a70] pci_device_probe+0xf8/0x1b8
[ca021d50] [c043d584] really_probe.part.0+0xac/0x388
[ca021d70] [c043d914] __driver_probe_device+0xb4/0x170
[ca021d90] [c043da18] driver_probe_device+0x48/0x144
[ca021dc0] [c043e318] __driver_attach+0x11c/0x1c4
[ca021de0] [c043ad30] bus_for_each_dev+0x88/0xf0
[ca021e10] [c043c724] bus_add_driver+0x190/0x22c
[ca021e40] [c043ee94] driver_register+0x9c/0x170
[ca021e60] [c0006c28] do_one_initcall+0x54/0x1ec
[ca021ed0] [c08246e4] kernel_init_freeable+0x1c0/0x270
[ca021f10] [c0006fdc] kernel_init+0x28/0x11c
[ca021f30] [c0017148] ret_from_kernel_thread+0x14/0x1c
Instruction dump:
7d4601a4 39490777 7d4701a4 39490888 7d4801a4 39490999 7d4901a4 39290aaa
7d2a01a4 4c00012c 4bfffe88 0fe00000 <4bfffe80> 9421fff0 38210010 48001970
This is due to 'dcbz' instruction being used on non-cached memory.
'dcbz' instruction is used by memset() to zeroize a complete
cacheline at once, and memset() is not expected to be used on non
cached memory.
When performing a 'sparse' check on fbdev driver, it also appears
that the use of memset() is unexpected:
drivers/video/fbdev/chipsfb.c:334:17: warning: incorrect type in argument 1 (different address spaces)
drivers/video/fbdev/chipsfb.c:334:17: expected void *
drivers/video/fbdev/chipsfb.c:334:17: got char [noderef] __iomem *screen_base
drivers/video/fbdev/chipsfb.c:334:15: warning: memset with byte count of 1048576
Use fb_memset() instead of memset(). fb_memset() is defined as
memset_io() for powerpc.
Fixes: 8c8709334c ("[PATCH] ppc32: Remove CONFIG_PMAC_PBOOK")
Reported-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/884a54f1e5cb774c1d9b4db780209bee5d4f6718.1631712563.git.christophe.leroy@csgroup.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ed2f3545c ]
The error handling code of fsl_ifc_ctrl_probe is problematic. When
fsl_ifc_ctrl_init fails or request_irq of fsl_ifc_ctrl_dev->irq fails,
it forgets to free the irq and nand_irq. Meanwhile, if request_irq of
fsl_ifc_ctrl_dev->nand_irq fails, it will still free nand_irq even if
the request_irq is not successful.
Fix this by refactoring the error handling code.
Fixes: d2ae2e20fb ("driver/memory:Move Freescale IFC driver to a common driver")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Link: https://lore.kernel.org/r/20210925151434.8170-1-mudongliangabcd@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 986b509470 ]
If an error occurs after a successful tegra_powergate_enable_clocks()
call, it must be undone by a tegra_powergate_disable_clocks() call, as
already done in the below and above error handling paths of this function.
Update the 'goto' to branch at the correct place of the error handling
path.
Fixes: a38045121b ("soc/tegra: pmc: Add generic PM domain support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 884ea75d79 ]
Fix typo in pinctrl. It did only work because the bootloader
seems to have initialized it.
Fixes: ee32711195 ("ARM: dts: omap3-gta04: Define and use bma180 irq pin")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df0a181494 ]
I got memory leak as follows:
unreferenced object 0xffff88801f0b2200 (size 64):
comm "i2c-lis2hh12-21", pid 5455, jiffies 4294944606 (age 15.224s)
hex dump (first 32 bytes):
72 65 67 75 6c 61 74 6f 72 3a 72 65 67 75 6c 61 regulator:regula
74 6f 72 2e 30 2d 2d 69 32 63 3a 31 2d 30 30 31 tor.0--i2c:1-001
backtrace:
[<00000000bf5b0c3b>] __kmalloc_track_caller+0x19f/0x3a0
[<0000000050da42d9>] kvasprintf+0xb5/0x150
[<000000004bbbed13>] kvasprintf_const+0x60/0x190
[<00000000cdac7480>] kobject_set_name_vargs+0x56/0x150
[<00000000bf83f8e8>] dev_set_name+0xc0/0x100
[<00000000cc1cf7e3>] device_link_add+0x6b4/0x17c0
[<000000009db9faed>] _regulator_get+0x297/0x680
[<00000000845e7f2b>] _devm_regulator_get+0x5b/0xe0
[<000000003958ee25>] st_sensors_power_enable+0x71/0x1b0 [st_sensors]
[<000000005f450f52>] st_accel_i2c_probe+0xd9/0x150 [st_accel_i2c]
[<00000000b5f2ab33>] i2c_device_probe+0x4d8/0xbe0
[<0000000070fb977b>] really_probe+0x299/0xc30
[<0000000088e226ce>] __driver_probe_device+0x357/0x500
[<00000000c21dda32>] driver_probe_device+0x4e/0x140
[<000000004e650441>] __device_attach_driver+0x257/0x340
[<00000000cf1891b8>] bus_for_each_drv+0x166/0x1e0
When device_register() returns an error, the name allocated in dev_set_name()
will be leaked, the put_device() should be used instead of kfree() to give up
the device reference, then the name will be freed in kobject_cleanup() and the
references of consumer and supplier will be decreased in device_link_release_fn().
Fixes: 287905e68d ("driver core: Expose device link details in sysfs")
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Saravana Kannan <saravanak@google.com>
Reviewed-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210930085714.2057460-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4ca3871e2 ]
The commit f87e7f2589 ("ALSA: hda - Improved position reporting on
SKL+") changed the PCM position report for SKL+ chips to use DPIB, but
according to Pierre, DPIB is no best choice for the accurate position
reports and it often reports too early. The recommended method is
rather the classical position buffer.
This patch makes the PCM position reporting on SKL+ back to the
position buffer again.
Fixes: f87e7f2589 ("ALSA: hda - Improved position reporting on SKL+")
Suggested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210929072934.6809-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 472e18f63c ]
Make sure the HDA driver's display power reference is released during
shutdown/reboot.
During the shutdown/reboot sequence the pci device core calls the
pm_runtime_resume handler for all devices before calling the driver's
shutdown callback and so the HDA driver's runtime resume callback will
acquire a display power reference (on HSW/BDW). This triggers a power
reference held WARN on HSW/BDW in the i915 driver's subsequent shutdown
handler, which expects all display power references to be released by
that time.
Since the HDA controller is stopped in the shutdown handler in any case,
let's follow here the same sequence as the one during runtime suspend.
This will also reset the HDA link and drop the display power reference,
getting rid of the above WARN.
Tested on HSW.
v2:
- Fix the build for CONFIG_PM=n (Takashi)
- s/__azx_runtime_suspend/azx_shutdown_chip/
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/3618
References: https://lore.kernel.org/lkml/cea1f9a-52e0-b83-593d-52997fe1aaf6@er-systems.de
Reported-and-tested-by: Thomas Voegtle <tv@lio96.de>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://lore.kernel.org/r/20210623134601.2128663-1-imre.deak@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46243b85b0 ]
The position reporting on Intel Skylake and later chips via
azx_get_pos_skl() contains a udelay(20) call for the capture streams.
A call for this alone doesn't sound too harmful. However, as the
pointer PCM ops is one of the hottest path in the PCM operations --
especially for the timer-scheduled operations like PulseAudio -- such
a delay hogs CPU usage significantly in the total performance.
The code there was taken from the original code in ASoC SST Skylake
driver blindly. The udelay() is a workaround for the case where the
reported position is behind the period boundary at the timing
triggered from interrupts; applications often expect that the full
data is available for the whole period when returned (and also that's
the definition of the ALSA PCM period).
OTOH, HD-audio (legacy) driver has already some workarounds for the
delayed position reporting due to its relatively large FIFO, such as
the BDL position adjustment and the delayed period-elapsed call in the
work. That said, the udelay() is almost superfluous for HD-audio
driver unlike SST, and we can drop the udelay().
Though, the current code doesn't guarantee the full period readiness
as mentioned in the above, but rather it checks the wallclock and
detects the unexpected jump. That's one missing piece, and the drop
of udelay() needs a bit more sanity checks for the delayed handling.
This patch implements those: the drop of udelay() call in
azx_get_pos_skl() and the more proper check of hwptr in
azx_position_ok(). The latter change is applied only for the case
where the stream is running in the normal mode without
no_period_wakeup flag. When no_period_wakeup is set, it essentially
ignores the period handling and rather concentrates only on the
current position; which implies that we don't need to care about the
period boundary at all.
Fixes: f87e7f2589 ("ALSA: hda - Improved position reporting on SKL+")
Reported-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210929072934.6809-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 483de2b44c ]
While removing the size from the "reg" properties in pm8916.dtsi,
commit bd6429e810 ("ARM64: dts: qcom: Remove size elements from
pmic reg properties") mistakenly also removed the second register
address for the rtc@6000 device. That one did not represent the size
of the register region but actually the address of the second "alarm"
register region of the rtc@6000 device.
Now there are "reg-names" for two "reg" elements, but there is actually
only one "reg" listed.
Since the DT schema for "qcom,pm8941-rtc" only expects one "reg"
element anyway, just drop the "reg-names" entirely to fix this.
Fixes: bd6429e810 ("ARM64: dts: qcom: Remove size elements from pmic reg properties")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210928112945.25310-1-stephan@gerhold.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8199a0b31e ]
At the moment, playing audio on Secondary MI2S will just end up getting
stuck, without actually playing any audio. This happens because the wrong
bit clock is configured when playing audio on Secondary MI2S.
The PRI_I2S_CLK (better name: SPKR_I2S_CLK) is used by the SPKR audio mux
block that provides both Primary and Secondary MI2S.
The SEC_I2S_CLK (better name: MIC_I2S_CLK) is used by the MIC audio mux
block that provides Tertiary MI2S. Quaternary MI2S is also part of the
MIC audio mux but has its own clock (AUX_I2S_CLK).
This means that (quite confusingly) the SEC_I2S_CLK is not actually
used for Secondary MI2S as the name would suggest. Secondary MI2S
needs to have the same clock as Primary MI2S configured.
Fix the clock list for the lpass node in the device tree and add
a comment to clarify this confusing naming. With these changes,
audio can be played correctly on Secondary MI2S.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: 3761a3618f ("arm64: dts: qcom: add lpass node")
Tested-by: Vincent Knecht <vincent.knecht@mailoo.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210816181810.2242-1-stephan@gerhold.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c48a14dca2 ]
In jfs_mount, when diMount(ipaimap2) fails, it goes to errout35. However,
the following code does not free ipaimap2 allocated by diReadSpecial.
Fix this by refactoring the error handling code of jfs_mount. To be
specific, modify the lable name and free ipaimap2 when the above error
ocurrs.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f3b3c2bfa ]
mach/loongson64 fails to build when the FPU support is disabled:
arch/mips/loongson64/cop2-ex.c:45:15: error: implicit declaration of function ‘__is_fpu_owner’; did you mean ‘is_fpu_owner’? [-Werror=implicit-function-declaration]
arch/mips/loongson64/cop2-ex.c:98:30: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:99:30: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:131:43: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:137:38: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:203:30: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:219:30: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:283:38: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:301:38: error: ‘struct thread_struct’ has no member named ‘fpu’
Fixes: ef2f826c8f ("MIPS: Loongson-3: Enable the COP2 usage")
Suggested-by: Huacai Chen <chenhuacai@kernel.org>
Reviewed-by: Huacai Chen <chenhuacai@kernel.org>
Reported-by: k2ci robot <kernel-bot@kylinos.cn>
Signed-off-by: Jackie Liu <liuyun01@kylinos.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3e9431854 ]
On resume we can get a warning at kernel/time/timekeeping.c:824 for
timekeeping_suspended.
Let's fix this by adding separate functions for sysc_poll_reset_sysstatus()
and sysc_poll_reset_sysconfig() and have the new functions handle also
timekeeping_suspended.
If iopoll at some point supports timekeeping_suspended, we can just drop
the custom handling from these functions.
Fixes: d46f9fbec7 ("bus: ti-sysc: Use optional clocks on for enable and wait for softreset bit")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f46633565 ]
commit 4e5833884f ("arm64: dts: ti: k3-j721e-main: Add PCIe device
tree nodes") restricted PCIe bus numbers from 0 to 15 (due to SMMU
restriction in J721E). However since SMMU is not enabled, allow the full
supported bus numbers from 0 to 255.
Fixes: 4e5833884f ("arm64: dts: ti: k3-j721e-main: Add PCIe device tree nodes")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210915055358.19997-3-kishon@ti.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 932b4610f5 ]
As can be seen in RK3328's TRM the register range for the GPU is
0xff300000 to 0xff330000.
It would (and does in vendor kernel) overlap with the registers of
the HEVC encoder (node/driver do not exist yet in upstream kernel).
See already existing h265e_mmu node.
Fixes: 752fbc0c8d ("arm64: dts: rockchip: add rk3328 mali gpu node")
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20210623115926.164861-1-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f0b3e0cc0 ]
Up until commit ea7e586bdd ("iio: st_sensors: move regulator retrieveal
to core") only the ST pressure driver seems to have had any regulator
disable. After that commit, the regulator handling was moved into the
common st_sensors logic.
In all instances of this regulator handling, the regulators were disabled
before unregistering the IIO device.
This can cause issues where the device would be powered down and still be
available to userspace, allowing it to send invalid/garbage data.
This change moves the st_sensors_power_disable() after the common probe
functions. These common probe functions also handle unregistering the IIO
device.
Fixes: 774487611c ("iio: pressure-core: st: Provide support for the Vdd power supply")
Fixes: ea7e586bdd ("iio: st_sensors: move regulator retrieveal to core")
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Denis CIOCCA <denis.ciocca@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210823112204.243255-2-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b9979db834 ]
Before this fix:
166: (b5) if r2 <= 0x1 goto pc+22
from 166 to 189: R2=invP(id=1,umax_value=1,var_off=(0x0; 0xffffffff))
After this fix:
166: (b5) if r2 <= 0x1 goto pc+22
from 166 to 189: R2=invP(id=1,umax_value=1,var_off=(0x0; 0x1))
While processing BPF_JLE the reg_set_min_max() would set true_reg->umax_value = 1
and call __reg_combine_64_into_32(true_reg).
Without the fix it would not pass the condition:
if (__reg64_bound_u32(reg->umin_value) && __reg64_bound_u32(reg->umax_value))
since umin_value == 0 at this point.
Before commit 10bf4e8316 the umin was incorrectly ingored.
The commit 10bf4e8316 fixed the correctness issue, but pessimized
propagation of 64-bit min max into 32-bit min max and corresponding var_off.
Fixes: 10bf4e8316 ("bpf: Fix propagation of 32 bit unsigned bounds from 64 bit bounds")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20211101222153.78759-1-alexei.starovoitov@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 81c49d39ae ]
In account_guest_time in kernel/sched/cputime.c guest time is
attributed to both CPUTIME_NICE and CPUTIME_USER in addition to
CPUTIME_GUEST_NICE and CPUTIME_GUEST respectively. Therefore, adding
both to calculate usage results in double counting any guest time at
the rootcg.
Fixes: 936f2a70f2 ("cgroup: add cpu.stat file to root cgroup")
Signed-off-by: Dan Schatzberg <schatzberg.dan@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e20d00158 ]
Soon after registering a CRQ it is possible that we get a fail over or
maybe a CRQ_INIT from the VIOS while interrupts were disabled.
Look for any such CRQs after enabling interrupts.
Otherwise we can intermittently fail to bring up ibmvnic adapters during
boot, specially in kexec/kdump kernels.
Fixes: 032c5e8284 ("Driver for IBM System i/p VNIC protocol")
Reported-by: Vaishnavi Bhat <vaish123@in.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8878e46fcf ]
If adapter's resetting bit is on, discard the packet but don't stop the
transmit queue - instead leave that to the reset code. With this change,
it is possible that we may get several calls to ibmvnic_xmit() that simply
discard packets and return.
But if we stop the queue here, we might end up doing so just after
__ibmvnic_open() started the queues (during a hard/soft reset) and before
the ->resetting bit was cleared. If that happens, there will be no one to
restart queue and transmissions will be blocked indefinitely.
This can cause a TIMEOUT reset and with auto priority failover enabled,
an unnecessary FAILOVER reset to less favored backing device and then a
FAILOVER back to the most favored backing device. If we hit the window
repeatedly, we can get stuck in a loop of TIMEOUT, FAILOVER, FAILOVER
resets leaving the adapter unusable for extended periods of time.
Fixes: 7f5b030830 ("ibmvnic: Free skb's in cases of failure in transmit")
Reported-by: Abdul Haleem <abdhalee@in.ibm.com>
Reported-by: Vaishnavi Bhat <vaish123@in.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42dcfd850e ]
Commit c6af0c227a ("ip: support SO_MARK cmsg")
added propagation of SO_MARK from cmsg to skb->mark.
For IPv4 and raw sockets the mark also affects route
lookup, but in case of IPv6 the flow info is
initialized before cmsg is parsed.
Fixes: c6af0c227a ("ip: support SO_MARK cmsg")
Reported-and-tested-by: Xintong Hu <huxintong@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68b6dea802 ]
These three events can race when pcrypt is used multiple times in a
template ("pcrypt(pcrypt(...))"):
1. [taskA] The caller makes the crypto request via crypto_aead_encrypt()
2. [kworkerB] padata serializes the inner pcrypt request
3. [kworkerC] padata serializes the outer pcrypt request
3 might finish before the call to crypto_aead_encrypt() returns in 1,
resulting in two possible issues.
First, a use-after-free of the crypto request's memory when, for
example, taskA writes to the outer pcrypt request's padata->info in
pcrypt_aead_enc() after kworkerC completes the request.
Second, the outer pcrypt request overwrites the inner pcrypt request's
return code with -EINPROGRESS, making a successful request appear to
fail. For instance, kworkerB writes the outer pcrypt request's
padata->info in pcrypt_aead_done() and then taskA overwrites it
in pcrypt_aead_enc().
Avoid both situations by delaying the write of padata->info until after
the inner crypto request's return code is checked. This prevents the
use-after-free by not touching the crypto request's memory after the
next-inner crypto request is made, and stops padata->info from being
overwritten.
Fixes: 5068c7a883 ("crypto: pcrypt - Add pcrypt crypto parallelization wrapper")
Reported-by: syzbot+b187b77c8474f9648fae@syzkaller.appspotmail.com
Signed-off-by: Daniel Jordan <daniel.m.jordan@oracle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd8d9731bc ]
mvneta does not support asymetric pause modes, and it flags this by the
lack of AsymPause in the supported field. When setting pause modes, we
check that pause->rx_pause == pause->tx_pause, but only when pause
autoneg is enabled. When pause autoneg is disabled, we still allow
pause->rx_pause != pause->tx_pause, which is incorrect when the MAC
does not support asymetric pause, and causes mvneta to issue a warning.
Fix this by removing the test for pause->autoneg, so we always check
that pause->rx_pause == pause->tx_pause for network devices that do not
support AsymPause.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit daf182d360 ]
For each rate change command submission, the FW has to do a phy
power off sequence internally. For this to happen correctly, the
PLL re-initialization control setting has to be turned off before
sending mailbox commands and re-enabled once the command submission
is complete.
Without the PLL control setting, the link up takes longer time in a
fixed phy configuration.
Fixes: 47f164deab ("amd-xgbe: Add PCI device support")
Co-developed-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Signed-off-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3fc706e94 ]
Similar to the fix in commit:
e31eec77e4 ("bpf: selftests: Fix fd cleanup in get_branch_snapshot")
We use designated initializer to set fds to -1 without breaking on
future changes to MAX_SERVER constant denoting the array size.
The particular close(0) occurs on non-reuseport tests, so it can be seen
with -n 115/{2,3} but not 115/4. This can cause problems with future
tests if they depend on BTF fd never being acquired as fd 0, breaking
internal libbpf assumptions.
Fixes: 0ab5539f85 ("selftests/bpf: Tests for BPF_SK_LOOKUP attach point")
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20211028063501.2239335-8-memxor@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 113f304dbc ]
The firmware is offering features such as ARP offload, for which
firmware crafts its own (QoS)packets without waking up the host.
Point is that the sequence numbers generated by the firmware are
not in sync with the host mac80211 layer and can cause packets
such as firmware ARP reponses to be dropped by the AP (too old SN).
To fix this we need to let the firmware manages the sequence
numbers by its own (except for QoS null frames). There is a SN
counter for each QoS queue and one global/baseline counter for
Non-QoS.
Fixes: 84aff52e4f ("wcn36xx: Use sequence number allocated by mac80211")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635150336-18736-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9bfe38e064 ]
This is essentially exactly following the dma_wmb()/dma_rmb() usage
instructions in Documentation/memory-barriers.txt.
The theoretical races here are:
1. DXE (the DMA Transfer Engine in the Wi-Fi subsystem) seeing the
dxe->ctrl & WCN36xx_DXE_CTRL_VLD write before the dxe->dst_addr_l
write, thus performing DMA into the wrong address.
2. CPU reading dxe->dst_addr_l before DXE unsets dxe->ctrl &
WCN36xx_DXE_CTRL_VLD. This should generally be harmless since DXE
doesn't write dxe->dst_addr_l (no risk of freeing the wrong skb).
Fixes: 8e84c25821 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware")
Signed-off-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211023001528.3077822-1-benl@squareup.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 85f517b294 ]
If handle_sske cannot set the storage key, because there is no
page table entry or no present large page entry, it calls
fixup_user_fault.
However, currently, if the call succeeds, handle_sske returns
-EAGAIN, without having set the storage key.
Instead, retry by continue'ing the loop without incrementing the
address.
The same issue in handle_pfmf was fixed by
a11bdb1a6b ("KVM: s390: Fix pfmf and conditional skey emulation").
Fixes: bd096f6443 ("KVM: s390: Add skey emulation fault handling")
Signed-off-by: Janis Schoetterl-Glausch <scgl@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Link: https://lore.kernel.org/r/20211022152648.26536-1-scgl@linux.ibm.com
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f76fbbbb50 ]
Use the actual return value instead of always -1 if register_kretprobe()
failed.
E.g. without this patch:
# insmod samples/kprobes/kretprobe_example.ko func=no_such_func
insmod: ERROR: could not insert module samples/kprobes/kretprobe_example.ko: Operation not permitted
With this patch:
# insmod samples/kprobes/kretprobe_example.ko func=no_such_func
insmod: ERROR: could not insert module samples/kprobes/kretprobe_example.ko: Unknown symbol in module
Link: https://lkml.kernel.org/r/1635213091-24387-2-git-send-email-yangtiezhu@loongson.cn
Fixes: 804defea1c ("Kprobes: move kprobe examples to samples/")
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf12e6f912 ]
v1: Implement a more general statement as recommended by Eric Dumazet. The
sequence number will be advanced, so this check will fix the FIN case and
other cases.
A customer reported sockets stuck in the CLOSING state. A Vmcore revealed that
the write_queue was not empty as determined by tcp_write_queue_empty() but the
sk_buff containing the FIN flag had been freed and the socket was zombied in
that state. Corresponding pcaps show no FIN from the Linux kernel on the wire.
Some instrumentation was added to the kernel and it was found that there is a
timing window where tcp_sendmsg() can run after tcp_send_fin().
tcp_sendmsg() will hit an error, for example:
1269 ▹ if (sk->sk_err || (sk->sk_shutdown & SEND_SHUTDOWN))↩
1270 ▹ ▹ goto do_error;↩
tcp_remove_empty_skb() will then free the FIN sk_buff as "skb->len == 0". The
TCP socket is now wedged in the FIN-WAIT-1 state because the FIN is never sent.
If the other side sends a FIN packet the socket will transition to CLOSING and
remain that way until the system is rebooted.
Fix this by checking for the FIN flag in the sk_buff and don't free it if that
is the case. Testing confirmed that fixed the issue.
Fixes: fdfc5c8594 ("tcp: remove empty skb from write queue in error cases")
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Reported-by: Monir Zouaoui <Monir.Zouaoui@mail.schwarz>
Reported-by: Simon Stier <simon.stier@mail.schwarz>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45f2bebc80 ]
__BYTE_ORDER is supposed to be defined by a libc, and __BYTE_ORDER__ -
by a compiler. bpf_core_read.h checks __BYTE_ORDER == __LITTLE_ENDIAN,
which is true if neither are defined, leading to incorrect behavior on
big-endian hosts if libc headers are not included, which is often the
case.
Fixes: ee26dade0e ("libbpf: Add support for relocatable bitfields")
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20211026010831.748682-2-iii@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7eba41fe8c ]
In commit c46ed2281b ("tpm_tis_spi: add missing SPI device ID entries")
we added SPI IDs for all the DT aliases to handle the fact that we always
use SPI modaliases to load modules even when probed via DT however the
mentioned commit missed that the SPI and OF device ID entries did not
match and were different and so DT nodes with compatible
"tcg,tpm_tis-spi" will not match. Add an extra ID for tpm_tis-spi
rather than just fix the existing one since what's currently there is
going to be better for anyone actually using SPI IDs to instantiate.
Fixes: c46ed2281b ("tpm_tis_spi: add missing SPI device ID entries")
Fixes: 96c8395e21 ("spi: Revert modalias changes")
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79ca6f74da ]
The Atmel TPM 1.2 chips crash with error
`tpm_try_transmit: send(): error -62` since kernel 4.14.
It is observed from the kernel log after running `tpm_sealdata -z`.
The error thrown from the command is as follows
```
$ tpm_sealdata -z
Tspi_Key_LoadKey failed: 0x00001087 - layer=tddl,
code=0087 (135), I/O error
```
The issue was reproduced with the following Atmel TPM chip:
```
$ tpm_version
T0 TPM 1.2 Version Info:
Chip Version: 1.2.66.1
Spec Level: 2
Errata Revision: 3
TPM Vendor ID: ATML
TPM Version: 01010000
Manufacturer Info: 41544d4c
```
The root cause of the issue is due to the TPM calls to msleep()
were replaced with usleep_range() [1], which reduces
the actual timeout. Via experiments, it is observed that
the original msleep(5) actually sleeps for 15ms.
Because of a known timeout issue in Atmel TPM 1.2 chip,
the shorter timeout than 15ms can cause the error described above.
A few further changes in kernel 4.16 [2] and 4.18 [3, 4] further
reduced the timeout to less than 1ms. With experiments,
the problematic timeout in the latest kernel is the one
for `wait_for_tpm_stat`.
To fix it, the patch reverts the timeout of `wait_for_tpm_stat`
to 15ms for all Atmel TPM 1.2 chips, but leave it untouched
for Ateml TPM 2.0 chip, and chips from other vendors.
As explained above, the chosen 15ms timeout is
the actual timeout before this issue introduced,
thus the old value is used here.
Particularly, TPM_ATML_TIMEOUT_WAIT_STAT_MIN is set to 14700us,
TPM_ATML_TIMEOUT_WAIT_STAT_MIN is set to 15000us according to
the existing TPM_TIMEOUT_RANGE_US (300us).
The fixed has been tested in the system with the affected Atmel chip
with no issues observed after boot up.
References:
[1] 9f3fc7bcdd tpm: replace msleep() with usleep_range() in TPM
1.2/2.0 generic drivers
[2] cf151a9a44 tpm: reduce tpm polling delay in tpm_tis_core
[3] 59f5a6b07f tpm: reduce poll sleep time in tpm_transmit()
[4] 424eaf910c tpm: reduce polling time to usecs for even finer
granularity
Fixes: 9f3fc7bcdd ("tpm: replace msleep() with usleep_range() in TPM 1.2/2.0 generic drivers")
Link: https://patchwork.kernel.org/project/linux-integrity/patch/20200926223150.109645-1-hao.wu@rubrik.com/
Signed-off-by: Hao Wu <hao.wu@rubrik.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c65b52d02f ]
As bcm6345_l1_irq_handle() is a chained irqchip handler, it will be
invoked within the context of the root irqchip handler, which must have
entered IRQ context already.
When bcm6345_l1_irq_handle() calls arch/mips's do_IRQ() , this will nest
another call to irq_enter(), and the resulting nested increment to
`rcu_data.dynticks_nmi_nesting` will cause rcu_is_cpu_rrupt_from_idle()
to fail to identify wakeups from idle, resulting in failure to preempt,
and RCU stalls.
Chained irqchip handlers must invoke IRQ handlers by way of thee core
irqchip code, i.e. generic_handle_irq() or generic_handle_domain_irq()
and should not call do_IRQ(), which is intended only for root irqchip
handlers.
Fix bcm6345_l1_irq_handle() by calling generic_handle_irq() directly.
Fixes: c7c42ec2ba ("irqchips/bmips: Add bcm6345-l1 interrupt controller")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d4074324b0 ]
If kvm_s390_pv_destroy_cpu is called more than once, we risk calling
free_page on a random page, since the sidad field is aliased with the
gbea, which is not guaranteed to be zero.
This can happen, for example, if userspace calls the KVM_PV_DISABLE
IOCTL, and it fails, and then userspace calls the same IOCTL again.
This scenario is only possible if KVM has some serious bug or if the
hardware is broken.
The solution is to simply return successfully immediately if the vCPU
was already non secure.
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Fixes: 19e1227768 ("KVM: S390: protvirt: Introduce instruction data area bounce buffer")
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <20210920132502.36111-3-imbrenda@linux.ibm.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b159f94c86 ]
... otherwise we will try unlocking a spinlock that was never locked via a
garbage pointer.
At the time we reach this code path, we usually successfully looked up
a PGSTE already; however, evil user space could have manipulated the VMA
layout in the meantime and triggered removal of the page table.
Fixes: 1e133ab296 ("s390/mm: split arch/s390/mm/pgtable.c")
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Link: https://lore.kernel.org/r/20210909162248.14969-3-david@redhat.com
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5245dafe3d ]
btf_header's str_off+str_len or type_off+type_len can overflow as they
are u32s. This will lead to bypassing the sanity checks during BTF
parsing, resulting in crashes afterwards. Fix by using 64-bit signed
integers for comparison.
Fixes: d812362450 ("libbpf: Fix BTF data layout checks and allow empty BTF")
Reported-by: Evgeny Vereshchagin <evvers@ya.ru>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20211023003157.726961-1-andrii@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d812362450 ]
Make data section layout checks stricter, disallowing overlap of types and
strings data.
Additionally, allow BTFs with no type data. There is nothing inherently wrong
with having BTF with no types (put potentially with some strings). This could
be a situation with kernel module BTFs, if module doesn't introduce any new
type information.
Also fix invalid offset alignment check for btf->hdr->type_off.
Fixes: 8a138aed4a ("bpf: btf: Add BTF support to libbpf")
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20201105043402.2530976-8-andrii@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e89ef634f8 ]
Bpftool creates a new JSON object for writing program metadata in plain
text mode, regardless of metadata being present or not. Then this writer
is freed if any metadata has been found and printed, but it leaks
otherwise. We cannot destroy the object unconditionally, because the
destructor prints an undesirable line break. Instead, make sure the
writer is created only after we have found program metadata to print.
Found with valgrind.
Fixes: aff52e685e ("bpftool: Support dumping metadata")
Signed-off-by: Quentin Monnet <quentin@isovalent.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20211022094743.11052-1-quentin@isovalent.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed290e1c20 ]
Though gcc conveniently compiles a simple memset to "rep stos," clang
prefers to call the libc version of memset. If a test is dynamically
linked, the libc memset isn't available in L1 (nor is the PLT or the
GOT, for that matter). Even if the test is statically linked, the libc
memset may choose to use some CPU features, like AVX, which may not be
enabled in L1. Note that __builtin_memset doesn't solve the problem,
because (a) the compiler is free to call memset anyway, and (b)
__builtin_memset may also choose to use features like AVX, which may
not be available in L1.
To avoid a myriad of problems, use an explicit "rep stos" to clear the
VMCB in generic_svm_setup(), which is called both from L0 and L1.
Reported-by: Ricardo Koller <ricarkol@google.com>
Signed-off-by: Jim Mattson <jmattson@google.com>
Fixes: 20ba262f86 ("selftests: KVM: AMD Nested test infrastructure")
Message-Id: <20210930003649.4026553-1-jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47bc726fe8 ]
Building the KVM selftests with LLVM's integrated assembler fails with:
$ CFLAGS=-fintegrated-as make -C tools/testing/selftests/kvm CC=clang
lib/x86_64/svm.c:77:16: error: too few operands for instruction
asm volatile ("vmsave\n\t" : : "a" (vmcb_gpa) : "memory");
^
<inline asm>:1:2: note: instantiated into assembly here
vmsave
^
lib/x86_64/svm.c:134:3: error: too few operands for instruction
"vmload\n\t"
^
<inline asm>:1:2: note: instantiated into assembly here
vmload
^
This is because LLVM IAS does not currently support calling vmsave,
vmload, or vmload without an explicit %rax operand.
Add an explicit operand to vmsave, vmload, and vmrum in svm.c. Fixing
this was suggested by Sean Christopherson.
Tested: building without this error in clang 11. The following patch
(not queued yet) needs to be applied to solve the other remaining error:
"selftests: kvm: remove reassignment of non-absolute variables".
Suggested-by: Sean Christopherson <seanjc@google.com>
Link: https://lore.kernel.org/kvm/X+Df2oQczVBmwEzi@google.com/
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Ricardo Koller <ricarkol@google.com>
Message-Id: <20210210031719.769837-1-ricarkol@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 01de5fcd8b ]
When building the kernel with sparse enabled 'C=1' the following
warnings shows up:
kernel/power/swap.c:390:29: warning: incorrect type in assignment (different base types)
kernel/power/swap.c:390:29: expected int ret
kernel/power/swap.c:390:29: got restricted blk_status_t
This is due to function hib_wait_io() returns a 'blk_status_t' which is
a bitwise u8. Commit 5416da01ff ("PM: hibernate: Remove
blk_status_to_errno in hib_wait_io") seemed to have mixed up the return
type. However, the 4e4cbee93d ("block: switch bios to blk_status_t")
actually broke the behaviour by returning the wrong type.
Rework so function hib_wait_io() returns a 'int' instead of
'blk_status_t' and make sure to call function
blk_status_to_errno(hb->error)' when returning from function
hib_wait_io() a int gets returned.
Fixes: 4e4cbee93d ("block: switch bios to blk_status_t")
Fixes: 5416da01ff ("PM: hibernate: Remove blk_status_to_errno in hib_wait_io")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0974812200 ]
In case that icdoff is not zero or mandatory keyed sgls are not
supported by the NVMe/RDMA target, we'll go to error flow but we'll
return 0 to the caller. Fix it by returning an appropriate error code.
Fixes: c66e2998c8 ("nvme-rdma: centralize controller setup sequence")
Signed-off-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2641b62d2f ]
Some Micrel KSZ8041NL PHY chips exhibit continuous RX errors after using
the power down mode bit (0.11). If the PHY is taken out of power down
mode in a certain temperature range, the PHY enters a weird state which
leads to continuously reporting RX errors. In that state, the MAC is not
able to receive or send any Ethernet frames and the activity LED is
constantly blinking. Since Linux is using the suspend callback when the
interface is taken down, ending up in that state can easily happen
during a normal startup.
Micrel confirmed the issue in errata DS80000700A [*], caused by abnormal
clock recovery when using power down mode. Even the latest revision (A4,
Revision ID 0x1513) seems to suffer that problem, and according to the
errata is not going to be fixed.
Remove the suspend/resume callback to avoid using the power down mode
completely.
[*] https://ww1.microchip.com/downloads/en/DeviceDoc/80000700A.pdf
Fixes: 1a5465f5d6 ("phy/micrel: Add suspend/resume support to Micrel PHYs")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd4bc63de7 ]
Coverity complains of a possible dereference of a null return value.
5. returned_null: kzalloc returns NULL. [show details]
6. var_assigned: Assigning: si_data = NULL return value from kzalloc.
488 si_data = kzalloc(data_size, __GFP_DMA | GFP_KERNEL);
489 cbd.length = cpu_to_le16(data_size);
490
491 dma = dma_map_single(&priv->si->pdev->dev, si_data,
492 data_size, DMA_FROM_DEVICE);
While this kzalloc() is unlikely to fail, I did notice that the function
returned without unmapping si_data.
Fix this by refactoring the error paths and checking for kzalloc()
failure.
Fixes: 888ae5a395 ("net: enetc: add tc flower psfp offload driver")
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org (open list)
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Acked-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc8a8bc374 ]
While looking at on-air packets using Wireshark, I noticed we're never
setting the initiator bit when sending DELBA requests to the AP: While
we set the bit on our del_ba_param_set bitmask, we forget to actually
copy that bitmask over to the command struct, which means we never
actually set the initiator bit.
Fix that and copy the bitmask over to the host_cmd_ds_11n_delba command
struct.
Fixes: 5e6e3a92b9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Acked-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211016153244.24353-5-verdre@v0yd.nl
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 515e7184bd ]
When fail to init coex module, free 'common' and 'adapter' directly, but
common->tx_thread which will access 'common' and 'adapter' is running at
the same time. That will trigger the UAF bug.
==================================================================
BUG: KASAN: use-after-free in rsi_tx_scheduler_thread+0x50f/0x520 [rsi_91x]
Read of size 8 at addr ffff8880076dc000 by task Tx-Thread/124777
CPU: 0 PID: 124777 Comm: Tx-Thread Not tainted 5.15.0-rc5+ #19
Call Trace:
dump_stack_lvl+0xe2/0x152
print_address_description.constprop.0+0x21/0x140
? rsi_tx_scheduler_thread+0x50f/0x520
kasan_report.cold+0x7f/0x11b
? rsi_tx_scheduler_thread+0x50f/0x520
rsi_tx_scheduler_thread+0x50f/0x520
...
Freed by task 111873:
kasan_save_stack+0x1b/0x40
kasan_set_track+0x1c/0x30
kasan_set_free_info+0x20/0x30
__kasan_slab_free+0x109/0x140
kfree+0x117/0x4c0
rsi_91x_init+0x741/0x8a0 [rsi_91x]
rsi_probe+0x9f/0x1750 [rsi_usb]
Stop thread before free 'common' and 'adapter' to fix it.
Fixes: 2108df3c4b ("rsi: add coex support")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211015040335.1021546-1-william.xuanziyang@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit afa0370f3a ]
Fix tag len error for sta_rec_wtbl, which causes fw parsing error for
the tags placed behind it.
Fixes: e57b790146 ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c33edef520 ]
Fix the following sparse warning in mt76x02_mac_write_txwi and
mt76x02_mac_tx_rate_val routines:
drivers/net/wireless/mediatek/mt76/mt76x02_mac.c:237:19:
warning: restricted __le16 degrades to intege
warning: cast from restricted __le16
drivers/net/wireless/mediatek/mt76/mt76x02_mac.c:383:28:
warning: incorrect type in assignment (different base types)
expected restricted __le16 [usertype] rate
got unsigned long
Fixes: db9f11d343 ("mt76: store wcid tx rate info in one u32 reduce locking")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd96e35ea7 ]
A new warning in clang points out a use of bitwise OR with boolean
expressions in this driver:
drivers/platform/x86/thinkpad_acpi.c:9061:11: error: use of bitwise '|' with boolean operands [-Werror,-Wbitwise-instead-of-logical]
else if ((strlencmp(cmd, "level disengaged") == 0) |
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
||
drivers/platform/x86/thinkpad_acpi.c:9061:11: note: cast one or both operands to int to silence this warning
1 error generated.
This should clearly be a logical OR so change it to fix the warning.
Fixes: fe98a52ce7 ("ACPI: thinkpad-acpi: add sysfs support to fan subdriver")
Link: https://github.com/ClangBuiltLinux/linux/issues/1476
Reported-by: Tor Vic <torvic9@mailbox.org>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20211018182537.2316800-1-nathan@kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24bcbe1cc6 ]
sk_stream_kill_queues() can be called on close when there are
still outstanding skbs to transmit. Those skbs may try to queue
notifications to the error queue (e.g. timestamps).
If sk_stream_kill_queues() purges the queue without taking
its lock the queue may get corrupted, and skbs leaked.
This shows up as a warning about an rmem leak:
WARNING: CPU: 24 PID: 0 at net/ipv4/af_inet.c:154 inet_sock_destruct+0x...
The leak is always a multiple of 0x300 bytes (the value is in
%rax on my builds, so RAX: 0000000000000300). 0x300 is truesize of
an empty sk_buff. Indeed if we dump the socket state at the time
of the warning the sk_error_queue is often (but not always)
corrupted. The ->next pointer points back at the list head,
but not the ->prev pointer. Indeed we can find the leaked skb
by scanning the kernel memory for something that looks like
an skb with ->sk = socket in question, and ->truesize = 0x300.
The contents of ->cb[] of the skb confirms the suspicion that
it is indeed a timestamp notification (as generated in
__skb_complete_tx_timestamp()).
Removing purging of sk_error_queue should be okay, since
inet_sock_destruct() does it again once all socket refs
are gone. Eric suggests this may cause sockets that go
thru disconnect() to maintain notifications from the
previous incarnations of the socket, but that should be
okay since the race was there anyway, and disconnect()
is not exactly dependable.
Thanks to Jonathan Lemon and Omar Sandoval for help at various
stages of tracing the issue.
Fixes: cb9eff0978 ("net: new user space API for time stamping of incoming and outgoing packets")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2203bd0e5c ]
The msm_gem_new_impl() function cleans up after itself so there is no
need to call drm_gem_object_put(). Conceptually, it does not make sense
to call a kref_put() function until after the reference counting has
been initialized which happens immediately after this call in the
drm_gem_(private_)object_init() functions.
In the msm_gem_import() function the "obj" pointer is uninitialized, so
it will lead to a crash.
Fixes: 05b849111c ("drm/msm: prime support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211013081315.GG6010@kili
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19757cebf0 ]
Use of percpu_counter structure to track count of orphaned
sockets is causing problems on modern hosts with 256 cpus
or more.
Stefan Bach reported a serious spinlock contention in real workloads,
that I was able to reproduce with a netfilter rule dropping
incoming FIN packets.
53.56% server [kernel.kallsyms] [k] queued_spin_lock_slowpath
|
---queued_spin_lock_slowpath
|
--53.51%--_raw_spin_lock_irqsave
|
--53.51%--__percpu_counter_sum
tcp_check_oom
|
|--39.03%--__tcp_close
| tcp_close
| inet_release
| inet6_release
| sock_close
| __fput
| ____fput
| task_work_run
| exit_to_usermode_loop
| do_syscall_64
| entry_SYSCALL_64_after_hwframe
| __GI___libc_close
|
--14.48%--tcp_out_of_resources
tcp_write_timeout
tcp_retransmit_timer
tcp_write_timer_handler
tcp_write_timer
call_timer_fn
expire_timers
__run_timers
run_timer_softirq
__softirqentry_text_start
As explained in commit cf86a086a1 ("net/dst: use a smaller percpu_counter
batch for dst entries accounting"), default batch size is too big
for the default value of tcp_max_orphans (262144).
But even if we reduce batch sizes, there would still be cases
where the estimated count of orphans is beyond the limit,
and where tcp_too_many_orphans() has to call the expensive
percpu_counter_sum_positive().
One solution is to use plain per-cpu counters, and have
a timer to periodically refresh this cache.
Updating this cache every 100ms seems about right, tcp pressure
state is not radically changing over shorter periods.
percpu_counter was nice 15 years ago while hosts had less
than 16 cpus, not anymore by current standards.
v2: Fix the build issue for CONFIG_CRYPTO_DEV_CHELSIO_TLS=m,
reported by kernel test robot <lkp@intel.com>
Remove unused socket argument from tcp_too_many_orphans()
Fixes: dd24c00191 ("net: Use a percpu_counter for orphan_count")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Stefan Bach <sfb@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ef0c5c6b5 ]
There is a small race between copy_process() and sched_fork()
where child->sched_task_group point to an already freed pointer.
parent doing fork() | someone moving the parent
| to another cgroup
-------------------------------+-------------------------------
copy_process()
+ dup_task_struct()<1>
parent move to another cgroup,
and free the old cgroup. <2>
+ sched_fork()
+ __set_task_cpu()<3>
+ task_fork_fair()
+ sched_slice()<4>
In the worst case, this bug can lead to "use-after-free" and
cause panic as shown above:
(1) parent copy its sched_task_group to child at <1>;
(2) someone move the parent to another cgroup and free the old
cgroup at <2>;
(3) the sched_task_group and cfs_rq that belong to the old cgroup
will be accessed at <3> and <4>, which cause a panic:
[] BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
[] PGD 8000001fa0a86067 P4D 8000001fa0a86067 PUD 2029955067 PMD 0
[] Oops: 0000 [#1] SMP PTI
[] CPU: 7 PID: 648398 Comm: ebizzy Kdump: loaded Tainted: G OE --------- - - 4.18.0.x86_64+ #1
[] RIP: 0010:sched_slice+0x84/0xc0
[] Call Trace:
[] task_fork_fair+0x81/0x120
[] sched_fork+0x132/0x240
[] copy_process.part.5+0x675/0x20e0
[] ? __handle_mm_fault+0x63f/0x690
[] _do_fork+0xcd/0x3b0
[] do_syscall_64+0x5d/0x1d0
[] entry_SYSCALL_64_after_hwframe+0x65/0xca
[] RIP: 0033:0x7f04418cd7e1
Between cgroup_can_fork() and cgroup_post_fork(), the cgroup
membership and thus sched_task_group can't change. So update child's
sched_task_group at sched_post_fork() and move task_fork() and
__set_task_cpu() (where accees the sched_task_group) from sched_fork()
to sched_post_fork().
Fixes: 8323f26ce3 ("sched: Fix race in task_group")
Signed-off-by: Zhang Qiao <zhangqiao22@huawei.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lkml.kernel.org/r/20210915064030.2231-1-zhangqiao22@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a491167fe ]
Most of the txpower for the ath10k firmware is stored as twicepower (0.5 dB
steps). This isn't the case for max_antenna_gain - which is still expected
by the firmware as dB.
The firmware is converting it from dB to the internal (twicepower)
representation when it calculates the limits of a channel. This can be seen
in tpc_stats when configuring "12" as max_antenna_gain. Instead of the
expected 12 (6 dB), the tpc_stats shows 24 (12 dB).
Tested on QCA9888 and IPQ4019 with firmware 10.4-3.5.3-00057.
Fixes: 02256930d9 ("ath10k: use proper tx power unit")
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20190611172131.6064-1-sven@narfation.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ada61aa0b1 ]
I got memory leak as follows when doing fault injection test:
unreferenced object 0xffff888102740438 (size 8):
comm "27", pid 859, jiffies 4295031351 (age 143.992s)
hex dump (first 8 bytes):
68 77 6d 6f 6e 30 00 00 hwmon0..
backtrace:
[<00000000544b5996>] __kmalloc_track_caller+0x1a6/0x300
[<00000000df0d62b9>] kvasprintf+0xad/0x140
[<00000000d3d2a3da>] kvasprintf_const+0x62/0x190
[<000000005f8f0f29>] kobject_set_name_vargs+0x56/0x140
[<00000000b739e4b9>] dev_set_name+0xb0/0xe0
[<0000000095b69c25>] __hwmon_device_register+0xf19/0x1e50 [hwmon]
[<00000000a7e65b52>] hwmon_device_register_with_info+0xcb/0x110 [hwmon]
[<000000006f181e86>] devm_hwmon_device_register_with_info+0x85/0x100 [hwmon]
[<0000000081bdc567>] tmp421_probe+0x2d2/0x465 [tmp421]
[<00000000502cc3f8>] i2c_device_probe+0x4e1/0xbb0
[<00000000f90bda3b>] really_probe+0x285/0xc30
[<000000007eac7b77>] __driver_probe_device+0x35f/0x4f0
[<000000004953d43d>] driver_probe_device+0x4f/0x140
[<000000002ada2d41>] __device_attach_driver+0x24c/0x330
[<00000000b3977977>] bus_for_each_drv+0x15d/0x1e0
[<000000005bf2a8e3>] __device_attach+0x267/0x410
When device_register() returns an error, the name allocated in
dev_set_name() will be leaked, the put_device() should be used
instead of calling hwmon_dev_release() to give up the device
reference, then the name will be freed in kobject_cleanup().
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: bab2243ce1 ("hwmon: Introduce hwmon_device_register_with_groups")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20211012112758.2681084-1-yangyingliang@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4400bbf5b ]
The NTF_EXT_LEARNED neigh flag is usually propagated back to user space
upon dump of the neighbor table. However, when used in combination with
NTF_USE flag this is not the case despite exempting the entry from the
garbage collector. This results in inconsistent state since entries are
typically marked in neigh->flags with NTF_EXT_LEARNED, but here they are
not. Fix it by propagating the creation flag to ___neigh_create().
Before fix:
# ./ip/ip n replace 192.168.178.30 dev enp5s0 use extern_learn
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a REACHABLE
[...]
After fix:
# ./ip/ip n replace 192.168.178.30 dev enp5s0 use extern_learn
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a extern_learn REACHABLE
[...]
Fixes: 9ce33e4653 ("neighbour: support for NTF_EXT_LEARNED flag")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Roopa Prabhu <roopa@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit beae4a6258 ]
The "msh" pointer is device managed, meaning that memstick_alloc_host()
calls device_initialize() on it. That means that it can't be free
using kfree() but must instead be freed with memstick_free_host().
Otherwise it leads to a tiny memory leak of device resources.
Fixes: 60fdd931d5 ("memstick: add support for JMicron jmb38x MemoryStick host controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211011123912.GD15188@kili
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4853396f03 ]
clang-14 complains about a sanity check that always passes when the
page size is 64KB or larger:
drivers/memstick/core/ms_block.c:1739:21: error: result of comparison of constant 65536 with expression of type 'unsigned short' is always false [-Werror,-Wtautological-constant-out-of-range-compare]
if (msb->page_size > PAGE_SIZE) {
~~~~~~~~~~~~~~ ^ ~~~~~~~~~
This is fine, it will still work on all architectures, so just shut
up that warning with a cast.
Fixes: 0ab30494bc ("memstick: add support for legacy memorysticks")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210927094520.696665-1-arnd@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d806e334d0 ]
We need to restore context in a specified order with HCTL set in two
phases. This is similar to what omap_hsmmc_context_restore() is doing.
Otherwise SDIO can stop working on resume.
And for PM runtime and SDIO cards, we need to also save SYSCTL, IE and
ISE.
This should not be a problem currently, and these patches can be applied
whenever suitable.
Fixes: ee0f309263 ("mmc: sdhci-omap: Add Support for Suspend/Resume")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210921110029.21944-3-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e0e7bd38b ]
If sdhci-omap is configured for an unused device instance and the device
is not set as disabled, we can get a NULL pointer dereference:
Unable to handle kernel NULL pointer dereference at virtual address
00000045
...
(regulator_set_voltage) from [<c07d7008>] (mmc_regulator_set_ocr+0x44/0xd0)
(mmc_regulator_set_ocr) from [<c07e2d80>] (sdhci_set_ios+0xa4/0x490)
(sdhci_set_ios) from [<c07ea690>] (sdhci_omap_set_ios+0x124/0x160)
(sdhci_omap_set_ios) from [<c07c8e94>] (mmc_power_up.part.0+0x3c/0x154)
(mmc_power_up.part.0) from [<c07c9d20>] (mmc_start_host+0x88/0x9c)
(mmc_start_host) from [<c07cad34>] (mmc_add_host+0x58/0x7c)
(mmc_add_host) from [<c07e2574>] (__sdhci_add_host+0xf0/0x22c)
(__sdhci_add_host) from [<c07eaf68>] (sdhci_omap_probe+0x318/0x72c)
(sdhci_omap_probe) from [<c06a39d8>] (platform_probe+0x58/0xb8)
AFAIK we are not seeing this with the devices configured in the mainline
kernel but this can cause issues for folks bringing up their boards.
Fixes: 7d326930d3 ("mmc: sdhci-omap: Add OMAP SDHCI driver")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210921110029.21944-2-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87a7f321bb ]
Don't always reset the driver on a TX timeout. Attempt to
recover by kicking the queue in case an IRQ was missed.
Fixes: 9e5f7d26a4 ("gve: Add workqueue and reset support")
Signed-off-by: John Fraker <jfraker@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b793db5fc ]
The problem is that "channel" is an unsigned int, when it's less 5 the
value of "channel - 5" is not a negative number as one would expect but
is very high positive value instead.
This means that "start" becomes a very high positive value. The result
of that is that we never enter the "for (i = start; i <= end; i++) {"
loop. Instead of storing the result from b43legacy_radio_aci_detect()
it just uses zero.
Fixes: ef1a628d83 ("b43: Implement dynamic PHY API")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Michael Büsch <m@bues.ch>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211006073621.GE8404@kili
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1c8380b03 ]
The problem is that "channel" is an unsigned int, when it's less 5 the
value of "channel - 5" is not a negative number as one would expect but
is very high positive value instead.
This means that "start" becomes a very high positive value. The result
of that is that we never enter the "for (i = start; i <= end; i++) {"
loop. Instead of storing the result from b43legacy_radio_aci_detect()
it just uses zero.
Fixes: 75388acd0c ("[B43LEGACY]: add mac80211-based driver for legacy BCM43xx devices")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Michael Büsch <m@bues.ch>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211006073542.GD8404@kili
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6f5f0c8f7 ]
Currently mtk_rng_runtime_suspend/resume is called for both runtime pm
and system sleep operations.
This is wrong as these should only be runtime ops as the name already
suggests. Currently freezing the system will lead to a call to
mtk_rng_runtime_suspend even if the device currently isn't active. This
leads to a clock warning because it is disabled/unprepared although it
isn't enabled/prepared currently.
This patch fixes this by only setting the runtime pm ops and forces to
call the runtime pm ops from the system sleep ops as well if active but
not otherwise.
Fixes: 81d2b34508 ("hwrng: mtk - add runtime PM support")
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 18fcba469b ]
Upon receiving a PFVF message, check if the interrupt bit is set in the
message. If it is not, that means that the interrupt was probably
triggered by a collision. In this case, disregard the message and
re-enable the interrupts.
Fixes: ed8ccaef52 ("crypto: qat - Add support for SRIOV")
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b768e8a39 ]
Detect a PFVF collision between the local and the remote function by
checking if the message on the PFVF CSR has been overwritten.
This is done after the remote function confirms that the message has
been received, by clearing the interrupt bit, or the maximum number of
attempts (ADF_IOV_MSG_ACK_MAX_RETRY) to check the CSR has been exceeded.
Fixes: ed8ccaef52 ("crypto: qat - Add support for SRIOV")
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Co-developed-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69a10678e2 ]
mn88443x_cmn_power_on() did not handle possible errors of
clk_prepare_enable() and always finished successfully so that its caller
mn88443x_probe() did not care about failed preparing/enabling of clocks
as well.
Add missed error handling in both mn88443x_cmn_power_on() and
mn88443x_probe(). This required to change the return value of the former
from "void" to "int".
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 0f408ce894 ("media: dvb-frontends: add Socionext MN88443x ISDB-S/T demodulator driver")
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Co-developed-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Signed-off-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b1394892d ]
Relax this condition to make add and update commands idempotent for sets
with no timeout. The eval function already checks if the set element
timeout is available and updates it if the update command is used.
Fixes: 22fe54d5fe ("netfilter: nf_tables: add support for dynamic set updates")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7663ad9a5d ]
RCU managed to grow a few noinstr violations:
vmlinux.o: warning: objtool: rcu_dynticks_eqs_enter()+0x0: call to rcu_dynticks_task_trace_enter() leaves .noinstr.text section
vmlinux.o: warning: objtool: rcu_dynticks_eqs_exit()+0xe: call to rcu_dynticks_task_trace_exit() leaves .noinstr.text section
Fix them by adding __always_inline to the relevant trivial functions.
Also replace the noinstr with __always_inline for the existing
rcu_dynticks_task_*() functions since noinstr would force noinline
them, even when empty, which seems silly.
Fixes: 7d0c9c50c5 ("rcu-tasks: Avoid IPIing userspace/idle tasks if kernel is so built")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f4873fb6a ]
AMD Rome systems and later support interleaving between three identical
ranks within a channel.
Check for this mode by counting the number of enabled chip selects and
comparing their masks. If there are exactly three enabled chip selects
and their masks are identical, then three rank interleaving is enabled.
The size of a rank is determined from its mask value. However, three
rank interleaving doesn't follow the method of swapping an interleave
bit with the most significant bit. Rather, the interleave bit is flipped
and the most significant bit remains the same. There is only a single
interleave bit in this case.
Account for this when determining the chip select size by keeping the
most significant bit at its original value and ignoring any zero bits.
This will return a full bitmask in [MSB:1].
Fixes: e53a3b267f ("EDAC/amd64: Find Chip Select memory size using Address Mask")
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20211005154419.2060504-1-yazen.ghannam@amd.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa1a43262a ]
Currently, a debug message is printed if an inefficient state is detected
in the Energy Model. Unfortunately, it won't detect if the first state is
inefficient or if two successive states are. Fix this behavior.
Fixes: 27871f7a8a (PM: Introduce an Energy Model management framework)
Signed-off-by: Vincent Donnefort <vincent.donnefort@arm.com>
Reviewed-by: Quentin Perret <qperret@google.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4925642d54 ]
In tests with two Lima boards from 8devices (QCA4531 based) on OpenWrt
19.07 we could force a silent restart of a device with no serial
output when we were sending a high amount of UDP traffic (iperf3 at 80
MBit/s in both directions from external hosts, saturating the wifi and
causing a load of about 4.5 to 6) and were then triggering an
ath9k_queue_reset().
Further debugging showed that the restart was caused by the ath79
watchdog. With disabled watchdog we could observe that the device was
constantly going into ath_isr() interrupt handler and was returning
early after the ATH_OP_HW_RESET flag test, without clearing any
interrupts. Even though ath9k_queue_reset() calls
ath9k_hw_kill_interrupts().
With JTAG we could observe the following race condition:
1) ath9k_queue_reset()
...
-> ath9k_hw_kill_interrupts()
-> set_bit(ATH_OP_HW_RESET, &common->op_flags);
...
<- returns
2) ath9k_tasklet()
...
-> ath9k_hw_resume_interrupts()
...
<- returns
3) loops around:
...
handle_int()
-> ath_isr()
...
-> if (test_bit(ATH_OP_HW_RESET,
&common->op_flags))
return IRQ_HANDLED;
x) ath_reset_internal():
=> never reached <=
And in ath_isr() we would typically see the following interrupts /
interrupt causes:
* status: 0x00111030 or 0x00110030
* async_cause: 2 (AR_INTR_MAC_IPQ)
* sync_cause: 0
So the ath9k_tasklet() reenables the ath9k interrupts
through ath9k_hw_resume_interrupts() which ath9k_queue_reset() had just
disabled. And ath_isr() then keeps firing because it returns IRQ_HANDLED
without actually clearing the interrupt.
To fix this IRQ storm also clear/disable the interrupts again when we
are in reset state.
Cc: Sven Eckelmann <sven@narfation.org>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Cc: Linus Lüssing <linus.luessing@c0d3.blue>
Fixes: 872b5d814f ("ath9k: do not access hardware on IRQs during reset")
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914192515.9273-3-linus.luessing@c0d3.blue
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51fa3b70d2 ]
The call to ops->suspend for the dev->dev_next case can currently
trigger a call on a null function pointer if ops->suspend is null.
Skip over the use of function ops->suspend if it is null.
Addresses-Coverity: ("Dereference after null check")
Fixes: be7fd3c3a8 ("media: em28xx: Hauppauge DualHD second tuner functionality")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5f5a66c9a ]
Commit c343bf1ba5 ("cpuidle: Fix three reference count leaks")
fixes the cleanup of kobjects; however, it removes kfree() calls
altogether, leading to memory leaks.
Fix those and also defer the initialization of dev->kobj_dev until
after the error check, so that we do not end up with a dangling
pointer.
Fixes: c343bf1ba5 ("cpuidle: Fix three reference count leaks")
Signed-off-by: Anel Orazgaliyeva <anelkz@amazon.de>
Suggested-by: Aman Priyadarshi <apeureka@amazon.de>
[ rjw: Subject edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 38aa192a05 ]
The ecc.c file started out as part of the ECDH algorithm but got
moved out into a standalone module later. It does not build without
CRYPTO_DEFAULT_RNG, so now that other modules are using it as well we
can run into this link error:
aarch64-linux-ld: ecc.c:(.text+0xfc8): undefined reference to `crypto_default_rng'
aarch64-linux-ld: ecc.c:(.text+0xff4): undefined reference to `crypto_put_default_rng'
Move the 'select CRYPTO_DEFAULT_RNG' statement into the correct symbol.
Fixes: 0d7a78643f ("crypto: ecrdsa - add EC-RDSA (GOST 34.10) algorithm")
Fixes: 4e6602916b ("crypto: ecdsa - Add support for ECDSA signature verification")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f7262cd66 ]
debugfs_create_file() takes a pointer argument that can be used during
file operation callbacks (accessible via i_private in the inode
structure). An obvious requirement is for the pointer to refer to
valid memory when used.
When creating the debugfs file to dynamically enable / disable
kprobes, a pointer to local variable is passed to
debugfs_create_file(); which will go out of scope when the init
function returns. The reason this hasn't triggered random memory
corruption is because the pointer is not accessed during the debugfs
file callbacks.
Since the enabled state is managed by the kprobes_all_disabled global
variable, the local variable is not needed. Fix the incorrect (and
unnecessary) usage of local variable during debugfs_file_create() by
passing NULL instead.
Link: https://lkml.kernel.org/r/163163031686.489837.4476867635937014973.stgit@devnote2
Fixes: bf8f6e5b3e ("Kprobes: The ON/OFF knob thru debugfs")
Signed-off-by: Punit Agrawal <punitagrawal@gmail.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7266dda2f1 ]
Currently a call to snd_card_new that fails will set card with a NULL
pointer, this causes a null pointer dereference on the error cleanup
path when card it passed to snd_card_free. Fix this by adding a new
error exit path that does not call snd_card_free and exiting via this
new path.
Addresses-Coverity: ("Explicit null dereference")
Fixes: 9e44d63246 ("[media] cx23885: Add ALSA support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42bb98e420 ]
The "card" string only holds 31 characters (and the terminating NUL).
In order to avoid truncation, use a shorter card description instead of
the current result, "Trident TVMaster TM5600/6000/60".
Suggested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: e28f49b0b2 ("V4L/DVB: tm6000: fix some info messages")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2908249f38 ]
The "card" string only holds 31 characters (and the terminating NUL).
In order to avoid truncation, use a shorter card description instead of
the current result, "Silicon Labs Si470x FM Radio Re".
Suggested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 78656acdcf ("V4L/DVB (7038): USB radio driver for Silicon Labs Si470x FM Radio Receivers")
Fixes: cc35bbddfe ("V4L/DVB (12416): radio-si470x: add i2c driver for si470x")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dfadec236a ]
The "card" string only holds 31 characters (and the terminating NUL).
In order to avoid truncation, use a shorter card description instead of
the current result, "Texas Instruments Wl1273 FM Rad".
Suggested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 87d1a50ce4 ("[media] V4L2: WL1273 FM Radio: TI WL1273 FM radio driver")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2143ad413c ]
A successful 'clk_prepare()' call should be balanced by a corresponding
'clk_unprepare()' call in the error handling path of the probe, as already
done in the remove function.
Update the error handling path accordingly.
Fixes: 3003a180ef ("[media] VPU: mediatek: support Mediatek VPU")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Houlong Wei <houlong.wei@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48d219f9cc ]
Static analysis reports this representative problem
tda1997x.c:1939: warning: 7th function call argument is an uninitialized
value
The 7th argument is buffer[0], which is set in the earlier call to
io_readn(). When io_readn() call to io_read() fails with the first
read, buffer[0] is not set and 0 is returned and stored in len.
The later call to hdmi_infoframe_unpack()'s size parameter is the
static size of buffer, always 40, so a short read is not caught
in hdmi_infoframe_unpacks()'s checking. The variable len should be
used instead.
Zero initialize buffer to 0 so it is in a known start state.
Fixes: 9ac0038db9 ("media: i2c: Add TDA1997x HDMI receiver driver")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c87ed93574 ]
If the driver does not implement s_ctrl, but it does implement
s_ext_ctrls, we convert the call.
When that happens we have also to convert back the response from
s_ext_ctrls.
Fixes v4l2_compliance:
Control ioctls (Input 0):
fail: v4l2-test-controls.cpp(411): returned control value out of range
fail: v4l2-test-controls.cpp(507): invalid control 00980900
test VIDIOC_G/S_CTRL: FAIL
Fixes: 35ea11ff84 ("V4L/DVB (8430): videodev: move some functions from v4l2-dev.h to v4l2-common.h or v4l2-ioctl.h")
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11b982e950 ]
Currently the null pointer check on dvb_spi->vcc_supply is inverted and
this leads to only null values of the dvb_spi->vcc_supply being passed
to the call of regulator_disable causing null pointer dereferences.
Fix this by only calling regulator_disable if dvb_spi->vcc_supply is
not null.
Addresses-Coverity: ("Dereference after null check")
Fixes: dcb0145821 ("media: cxd2880-spi: Fix an error handling path")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 335aea75b0 ]
The overflow check in amdgpu_bo_list_create() causes a warning with
clang-14 on 64-bit architectures, since the limit can never be
exceeded.
drivers/gpu/drm/amd/amdgpu/amdgpu_bo_list.c:74:18: error: result of comparison of constant 256204778801521549 with expression of type 'unsigned int' is always false [-Werror,-Wtautological-constant-out-of-range-compare]
if (num_entries > (SIZE_MAX - sizeof(struct amdgpu_bo_list))
~~~~~~~~~~~ ^ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The check remains useful for 32-bit architectures, so just avoid the
warning by using size_t as the type for the count.
Fixes: 920990cb08 ("drm/amdgpu: allocate the bo_list array after the list")
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 019edd01d1 ]
On a i.MX-based board with a QCA9377 Wifi chip, the following errors
are seen after launching the 'hostapd' application:
hostapd /etc/wifi.conf
Configuration file: /etc/wifi.conf
wlan0: interface state UNINITIALIZED->COUNTRY_UPDATE
NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!
Using interface wlan0 with hwaddr 00:1f:7b:31:04:a0 and ssid "thessid"
IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
wlan0: interface state COUNTRY_UPDATE->ENABLED
wlan0: AP-ENABLED
NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!
NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!
NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!
NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!
...
Fix this problem by adding the BH locking around napi-schedule(),
in the same way it was done in commit e63052a5dd ("mlx5e: add
add missing BH locking around napi_schdule()").
Its commit log provides the following explanation:
"It's not correct to call napi_schedule() in pure process
context. Because we use __raise_softirq_irqoff() we require
callers to be in a context which will eventually lead to
softirq handling (hardirq, bh disabled, etc.).
With code as is users will see:
NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!
"
Fixes: cfee8793a7 ("ath10k: enable napi on RX path for sdio")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210824144339.2796122-1-festevam@denx.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6dfbc3ba9 ]
When receiving a beacon or probe response, we should update the
boottime_ns field which is the timestamp the frame was received at.
(cf mac80211.h)
This fixes a scanning issue with Android since it relies on this
timestamp to determine when the AP has been seen for the last time
(via the nl80211 BSS_LAST_SEEN_BOOTTIME parameter).
Fixes: 5e3dd157d7 ("ath10k: mac80211 driver for Qualcomm Atheros 802.11ac CQA98xx devices")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1629811733-7927-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1db2b0d0a3 ]
Whenever ath11k is bootup with a user country already set, cfg80211
notifies this country info to ath11k soon after registration, where the
notification is sent to the firmware for fetching the rules of this user
country input.
Multiple race conditions could be seen in this scenario where a new
request is either lost as pointed in [1] or a new regd overwrites the
default regd provided by the firmware during bootup. Note that, the
default regd is used for intersection purpose and hence it should not be
overwritten.
The main reason as pointed by [1] is the usage of ATH11K_FLAG_REGISTERED
flag which is updated after completion of core registration, whereas the
reg notification from cfg80211 and wmi events for the corresponding
request can happen much before that. Since the ATH11K_FLAG_REGISTERED is
currently used to determine if the event containing reg rules belong to
default regd or for user request, there is a possibility of the default
regd getting overwritten.
Since the default reg rules will be received only once per pdev on
firmware load, the above flag based check can be replaced with a check
to see if default_regd is already set, so that we can now always update
the new_regd. Also if the new_regd is set, this will be always used to
update the reg rules for the registered phy.
[1] https://patchwork.kernel.org/project/linux-wireless/patch/1829665.1PRlr7bOQj@ripper/
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01460-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-4-jouni@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aadf7c81a0 ]
The ath11k_dbring_bufs_replenish() and ath11k_dbring_fill_bufs()
take a "gfp" parameter but they since they take spinlocks, the
allocations they do have to be atomic. This causes a bug because
ath11k_dbring_buf_setup passes GFP_KERNEL for the gfp flags.
The fix is to use GFP_ATOMIC and remove the unused parameters.
Fixes: bd6478559e ("ath11k: Add direct buffer ring support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210812070434.GE31863@kili
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f5f12f5d4 ]
The max VLAN number with non-4K VLAN activated is 15, and the
range is 0..15. Not 16.
The impact should be low since we by default have 4K VLAN and
thus have 4095 VLANs to play with in this switch. There will
not be a problem unless the code is rewritten to only use
16 VLANs.
Fixes: d8652956cf ("net: dsa: realtek-smi: Add Realtek SMI driver")
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit acde891c24 ]
Directly using _usecs_to_jiffies() might be unsafe, so it's
better to use usecs_to_jiffies() instead.
Because we can see that the result of _usecs_to_jiffies()
could be larger than MAX_JIFFY_OFFSET values without the
check of the input.
Fixes: c410bf0193 ("Fix the excessive initial retransmission timeout")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f20311cc9c ]
On newer CAAM versions, not all accelerators are disabled if the SoC is
a non-E variant. While the driver checks most of the modules for
availability, there is one - PKHA - which sticks out. On non-E variants
it is still reported as available, that is the number of instances is
non-zero, but it has limited functionality. In particular it doesn't
support encryption and decryption, but just signing and verifying. This
is indicated by a bit in the PKHA_MISC field. Take this bit into account
if we are checking for availability.
This will the following error:
[ 8.167817] caam_jr 8020000.jr: 20000b0f: CCB: desc idx 11: : Invalid CHA selected.
Tested on an NXP LS1028A (non-E) SoC.
Fixes: d239b10d4c ("crypto: caam - add register map changes cf. Era 10")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e5f2d90c2 ]
bdev->evt_skb will get freed in the normal path and one error path
of mtk_hci_wmt_sync, while the other error paths do not free it,
which may cause a memleak. This bug is suggested by a static analysis
tool, please advise.
Fixes: e0b67035a9 ("Bluetooth: mediatek: update the common setup between MT7622 and other devices")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c719fed0f ]
When the BSS reference holds a valid reference, it is not freed. The 'if'
condition is wrong. Instead of the 'if (bss)' check, the 'if (!bss)' check
is used.
The issue is solved by removing the unnecessary 'if' check because
cfg80211_put_bss() already performs the NULL validation.
Fixes: 6cd4fa5ab6 ("staging: wilc1000: make use of cfg80211_inform_bss_frame()")
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-3-ajay.kathat@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 701668d3bf ]
We have been tracking a strange bug with Antenna Diversity Switching (ADS)
on wcn3680b for a while.
ADS is configured like this:
A. Via a firmware configuration table baked into the NV area.
1. Defines if ADS is enabled.
2. Defines which GPIOs are connected to which antenna enable pin.
3. Defines which antenna/GPIO is primary and which is secondary.
B. WCN36XX_CFG_VAL(ANTENNA_DIVERSITY, N)
N is a bitmask of available antenna.
Setting N to 3 indicates a bitmask of enabled antenna (1 | 2).
Obviously then we can set N to 1 or N to 2 to fix to a particular
antenna and disable antenna diversity.
C. WCN36XX_CFG_VAL(ASD_PROBE_INTERVAL, XX)
XX is the number of beacons between each antenna RSSI check.
Setting this value to 50 means, every 50 received beacons, run the
ADS algorithm.
D. WCN36XX_CFG_VAL(ASD_TRIGGER_THRESHOLD, YY)
YY is a two's complement integer which specifies the RSSI decibel
threshold below which ADS will run.
We default to -60db here, meaning a measured RSSI <= -60db will
trigger an ADS probe.
E. WCN36XX_CFG_VAL(ASD_RTT_RSSI_HYST_THRESHOLD, Z)
Z is a hysteresis value, indicating a delta which the RSSI must
exceed for the antenna switch to be valid.
For example if HYST_THRESHOLD == 3 AntennaId1-RSSI == -60db and
AntennaId-2-RSSI == -58db then firmware will not switch antenna.
The threshold needs to be -57db or better to satisfy the criteria.
F. A firmware feature bit also exists ANTENNA_DIVERSITY_SELECTION.
This feature bit is used by the firmware to report if
ANTENNA_DIVERSITY_SELECTION is supported. The host is not required to
toggle this bit to enable or disable ADS.
ADS works like this:
A. Every XX beacons the firmware switches to or remains on the primary
antenna.
B. The firmware then sends a Request-To-Send (RTS) packet to the AP.
C. The firmware waits for a Clear-To-Send (CTS) response from the AP.
D. The firmware then notes the received RSSI on the CTS packet.
E. The firmware then repeats steps A-D on the secondary antenna.
F. Subsequently if the RSSI on the measured antenna is better than
ASD_TRIGGER_THRESHOLD + the active antenna's RSSI then the
measured antenna becomes the active antenna.
G. If RSSI rises past ASD_TRIGGER_THRESHOLD then ADS doesn't run at
all even if there is a substantially better RSSI on the alternative
antenna.
What we have been observing is that the RTS packet is being sent but the
MAC address is a byte-swapped version of the target MAC. The ADS/RTS MAC is
corrupted only when the link is encrypted, if the AP is open the RTS MAC is
correct. Similarly if we configure the firmware to an RTS/CTS sequence for
regular data - the transmitted RTS MAC is correctly formatted.
Internally the wcn36xx firmware uses the indexes in the SMD commands to
populate and extract data from specific entries in an STA lookup table. The
AP's MAC appears a number of times in different indexes within this lookup
table, so the MAC address extracted for the data-transmit RTS and the MAC
address extracted for the ADS/RTS packet are not the same STA table index.
Our analysis indicates the relevant firmware STA table index is
"bssSelfStaIdx".
There is an STA populate function responsible for formatting the MAC
address of the bssSelfStaIdx including byte-swapping the MAC address.
Its clear then that the required STA populate command did not run for
bssSelfStaIdx.
So taking a look at the sequence of SMD commands sent to the firmware we
see the following downstream when moving from an unencrypted to encrypted
BSS setup.
- WLAN_HAL_CONFIG_BSS_REQ
- WLAN_HAL_CONFIG_STA_REQ
- WLAN_HAL_SET_STAKEY_REQ
Upstream in wcn36xx we have
- WLAN_HAL_CONFIG_BSS_REQ
- WLAN_HAL_SET_STAKEY_REQ
The solution then is to add the missing WLAN_HAL_CONFIG_STA_REQ between
WLAN_HAL_CONFIG_BSS_REQ and WLAN_HAL_SET_STAKEY_REQ.
No surprise WLAN_HAL_CONFIG_STA_REQ is the routine responsible for
populating the STA lookup table in the firmware and once done the MAC sent
by the ADS routine is in the correct byte-order.
This bug is apparent with ADS but it is also the case that any other
firmware routine that depends on the "bssSelfStaIdx" would retrieve
malformed data on an encrypted link.
Fixes: 3e977c5c52 ("wcn36xx: Define wcn3680 specific firmware parameters")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Benjamin Li <benl@squareup.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210909144428.2564650-2-bryan.odonoghue@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ee285395b ]
It was found that the following warning was displayed when remounting
controllers from cgroup v2 to v1:
[ 8042.997778] WARNING: CPU: 88 PID: 80682 at kernel/cgroup/cgroup.c:3130 cgroup_apply_control_disable+0x158/0x190
:
[ 8043.091109] RIP: 0010:cgroup_apply_control_disable+0x158/0x190
[ 8043.096946] Code: ff f6 45 54 01 74 39 48 8d 7d 10 48 c7 c6 e0 46 5a a4 e8 7b 67 33 00 e9 41 ff ff ff 49 8b 84 24 e8 01 00 00 0f b7 40 08 eb 95 <0f> 0b e9 5f ff ff ff 48 83 c4 08 5b 5d 41 5c 41 5d 41 5e 41 5f c3
[ 8043.115692] RSP: 0018:ffffba8a47c23d28 EFLAGS: 00010202
[ 8043.120916] RAX: 0000000000000036 RBX: ffffffffa624ce40 RCX: 000000000000181a
[ 8043.128047] RDX: ffffffffa63c43e0 RSI: ffffffffa63c43e0 RDI: ffff9d7284ee1000
[ 8043.135180] RBP: ffff9d72874c5800 R08: ffffffffa624b090 R09: 0000000000000004
[ 8043.142314] R10: ffffffffa624b080 R11: 0000000000002000 R12: ffff9d7284ee1000
[ 8043.149447] R13: ffff9d7284ee1000 R14: ffffffffa624ce70 R15: ffffffffa6269e20
[ 8043.156576] FS: 00007f7747cff740(0000) GS:ffff9d7a5fc00000(0000) knlGS:0000000000000000
[ 8043.164663] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 8043.170409] CR2: 00007f7747e96680 CR3: 0000000887d60001 CR4: 00000000007706e0
[ 8043.177539] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 8043.184673] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 8043.191804] PKRU: 55555554
[ 8043.194517] Call Trace:
[ 8043.196970] rebind_subsystems+0x18c/0x470
[ 8043.201070] cgroup_setup_root+0x16c/0x2f0
[ 8043.205177] cgroup1_root_to_use+0x204/0x2a0
[ 8043.209456] cgroup1_get_tree+0x3e/0x120
[ 8043.213384] vfs_get_tree+0x22/0xb0
[ 8043.216883] do_new_mount+0x176/0x2d0
[ 8043.220550] __x64_sys_mount+0x103/0x140
[ 8043.224474] do_syscall_64+0x38/0x90
[ 8043.228063] entry_SYSCALL_64_after_hwframe+0x44/0xae
It was caused by the fact that rebind_subsystem() disables
controllers to be rebound one by one. If more than one disabled
controllers are originally from the default hierarchy, it means that
cgroup_apply_control_disable() will be called multiple times for the
same default hierarchy. A controller may be killed by css_kill() in
the first round. In the second round, the killed controller may not be
completely dead yet leading to the warning.
To avoid this problem, we collect all the ssid's of controllers that
needed to be disabled from the default hierarchy and then disable them
in one go instead of one by one.
Fixes: 334c3679ec ("cgroup: reimplement rebind_subsystems() using cgroup_apply_control() and friends")
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aed0826b0c ]
The key_domain member in struct net only exists if we define CONFIG_KEYS.
So we should add the define when we used key_domain.
Fixes: 9b24261051 ("keys: Network namespace domain tag")
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2507003a1d ]
lock_is_held_type(, 1) detects acquired read locks. It only recognized
locks acquired with lock_acquire_shared(). Read locks acquired with
lock_acquire_shared_recursive() are not recognized because a `2' is
stored as the read value.
Rework the check to additionally recognise lock's read value one and two
as a read held lock.
Fixes: e918188611 ("locking: More accurate annotations for read_lock()")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Boqun Feng <boqun.feng@gmail.com>
Acked-by: Waiman Long <longman@redhat.com>
Link: https://lkml.kernel.org/r/20210903084001.lblecrvz4esl4mrr@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4f8681911 ]
The hardware sets the TMUWCF bit back to 0 when the TMU write
combiner flush completes so we should be checking for that instead
of the L2TFLS bit.
v2 (Melissa Wen):
- Add Signed-off-by and Fixes tags.
- Change the error message for the timeout to be more clear.
Fixes spurious Vulkan CTS failures in:
dEQP-VK.binding_model.descriptorset_random.*
Fixes: d223f98f02 ("drm/v3d: Add support for compute shader dispatch.")
Signed-off-by: Iago Toral Quiroga <itoral@igalia.com>
Reviewed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210915100507.3945-1-itoral@igalia.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9af9dcf11b ]
The asm_cpu_bringup_and_idle() function is required to push the return
value on the stack in order to make ORC happy, but the only reason
objtool doesn't complain is because of a happy accident.
The thing is that asm_cpu_bringup_and_idle() doesn't return, so
validate_branch() never terminates and falls through to the next
function, which in the normal case is the hypercall_page. And that, as
it happens, is 4095 NOPs and a RET.
Make asm_cpu_bringup_and_idle() terminate on it's own, by making the
function it calls as a dead-end. This way we no longer rely on what
code happens to come after.
Fixes: c3881eb58d ("x86/xen: Make the secondary CPU idle tasks reliable")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Link: https://lore.kernel.org/r/20210624095147.693801717@infradead.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ad74d39c5 ]
The current definition of 2W burst length is invalid.
This patch fixes it. Current downstream DEU driver doesn't
use DMA. An incorrect burst length value doesn't cause any
errors. This patch also adds other burst length values.
Fixes: dfec1a827d ("MIPS: Lantiq: Add DMA support")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f0b2b2df54 ]
The sync_sched_exp_online_cleanup() checks to see if RCU needs
an expedited quiescent state from the incoming CPU, sending it
an IPI if so. Before sending IPI, it checks whether expedited
qs need has been already requested for the incoming CPU, by
checking rcu_data.cpu_no_qs.b.exp for the current cpu, on which
sync_sched_exp_online_cleanup() is running. This works for the
case where incoming CPU is same as self. However, for the case
where incoming CPU is different from self, expedited request
won't get marked, which can potentially delay reporting of
expedited quiescent state for the incoming CPU.
Fixes: e015a34112 ("rcu: Avoid self-IPI in sync_sched_exp_online_cleanup()")
Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49d8a56064 ]
Before freeing struct sco_conn, all delayed timeout work should be
cancelled. Otherwise, sco_sock_timeout could potentially use the
sco_conn after it has been freed.
Additionally, sco_conn.timeout_work should be initialized when the
connection is allocated, not when the channel is added. This is
because an sco_conn can create channels with multiple sockets over its
lifetime, which happens if sockets are released but the connection
isn't deleted.
Fixes: ba316be1b6 ("Bluetooth: schedule SCO timeouts with delayed_work")
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7b1d02fc4 ]
The internal stream state sets the timeout to 120 seconds 2 seconds
after the creation of the flow, attach this internal stream state to the
IPS_ASSURED flag for consistent event reporting.
Before this patch:
[NEW] udp 17 30 src=10.246.11.13 dst=216.239.35.0 sport=37282 dport=123 [UNREPLIED] src=216.239.35.0 dst=10.246.11.13 sport=123 dport=37282
[UPDATE] udp 17 30 src=10.246.11.13 dst=216.239.35.0 sport=37282 dport=123 src=216.239.35.0 dst=10.246.11.13 sport=123 dport=37282
[UPDATE] udp 17 30 src=10.246.11.13 dst=216.239.35.0 sport=37282 dport=123 src=216.239.35.0 dst=10.246.11.13 sport=123 dport=37282 [ASSURED]
[DESTROY] udp 17 src=10.246.11.13 dst=216.239.35.0 sport=37282 dport=123 src=216.239.35.0 dst=10.246.11.13 sport=123 dport=37282 [ASSURED]
Note IPS_ASSURED for the flow not yet in the internal stream state.
after this update:
[NEW] udp 17 30 src=10.246.11.13 dst=216.239.35.0 sport=37282 dport=123 [UNREPLIED] src=216.239.35.0 dst=10.246.11.13 sport=123 dport=37282
[UPDATE] udp 17 30 src=10.246.11.13 dst=216.239.35.0 sport=37282 dport=123 src=216.239.35.0 dst=10.246.11.13 sport=123 dport=37282
[UPDATE] udp 17 120 src=10.246.11.13 dst=216.239.35.0 sport=37282 dport=123 src=216.239.35.0 dst=10.246.11.13 sport=123 dport=37282 [ASSURED]
[DESTROY] udp 17 src=10.246.11.13 dst=216.239.35.0 sport=37282 dport=123 src=216.239.35.0 dst=10.246.11.13 sport=123 dport=37282 [ASSURED]
Before this patch, short-lived UDP flows never entered IPS_ASSURED, so
they were already candidate flow to be deleted by early_drop under
stress.
Before this patch, IPS_ASSURED is set on regardless the internal stream
state, attach this internal stream state to IPS_ASSURED.
packet #1 (original direction) enters NEW state
packet #2 (reply direction) enters ESTABLISHED state, sets on IPS_SEEN_REPLY
paclet #3 (any direction) sets on IPS_ASSURED (if 2 seconds since the
creation has passed by).
Reported-by: Maciej Żenczykowski <zenczykowski@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66e29fcda1 ]
With idle polling, IPIs are not sent when a CPU idle, but queued
and run later from do_idle(). The default kgdb_call_nmi_hook()
implementation gets the pointer to struct pt_regs from get_irq_reqs(),
which doesn't work in that case because it was not called from the
IPI interrupt handler. Fix it by defining our own kgdb_roundup()
function which sents an IPI_ENTER_KGDB. When that IPI is received
on the target CPU kgdb_nmicallback() is called.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e0ba125c2 ]
With 64 bit kernels unwind_special() is not working because
it compares the pc to the address of the function descriptor.
Add a helper function that compares pc with the dereferenced
address. This fixes all of the backtraces on my c8000. Without
this changes, a lot of backtraces are missing in kdb or the
show-all-tasks command from /proc/sysrq-trigger.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9cc2fa4f4a ]
The function end_of_stack() returns a pointer to the last entry of a
stack. For architectures like parisc where the stack grows upwards
return the pointer to the highest address in the stack.
Without this change I faced a crash on parisc, because the stackleak
functionality wrote STACKLEAK_POISON to the lowest address and thus
overwrote the first 4 bytes of the task_struct which included the
TIF_FLAGS.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f35dcaa0a8 ]
close_range() test type conflicts with close_range() library call in
x86_64-linux-gnu/bits/unistd_ext.h. Fix it by changing the name to
core_close_range().
gcc -g -I../../../../usr/include/ close_range_test.c -o ../tools/testing/selftests/core/close_range_test
In file included from close_range_test.c:16:
close_range_test.c:57:6: error: conflicting types for ‘close_range’; have ‘void(struct __test_metadata *)’
57 | TEST(close_range)
| ^~~~~~~~~~~
../kselftest_harness.h:181:21: note: in definition of macro ‘__TEST_IMPL’
181 | static void test_name(struct __test_metadata *_metadata); \
| ^~~~~~~~~
close_range_test.c:57:1: note: in expansion of macro ‘TEST’
57 | TEST(close_range)
| ^~~~
In file included from /usr/include/unistd.h:1204,
from close_range_test.c:13:
/usr/include/x86_64-linux-gnu/bits/unistd_ext.h:56:12: note: previous declaration of ‘close_range’ with type ‘int(unsigned int, unsigned int, int)’
56 | extern int close_range (unsigned int __fd, unsigned int __max_fd,
| ^~~~~~~~~~~
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 285f68afa8 ]
The following issue is observed with CONFIG_DEBUG_PREEMPT when KVM loads:
KVM: vmx: using Hyper-V Enlightened VMCS
BUG: using smp_processor_id() in preemptible [00000000] code: systemd-udevd/488
caller is set_hv_tscchange_cb+0x16/0x80
CPU: 1 PID: 488 Comm: systemd-udevd Not tainted 5.15.0-rc5+ #396
Hardware name: Microsoft Corporation Virtual Machine/Virtual Machine, BIOS Hyper-V UEFI Release v4.0 12/17/2019
Call Trace:
dump_stack_lvl+0x6a/0x9a
check_preemption_disabled+0xde/0xe0
? kvm_gen_update_masterclock+0xd0/0xd0 [kvm]
set_hv_tscchange_cb+0x16/0x80
kvm_arch_init+0x23f/0x290 [kvm]
kvm_init+0x30/0x310 [kvm]
vmx_init+0xaf/0x134 [kvm_intel]
...
set_hv_tscchange_cb() can get preempted in between acquiring
smp_processor_id() and writing to HV_X64_MSR_REENLIGHTENMENT_CONTROL. This
is not an issue by itself: HV_X64_MSR_REENLIGHTENMENT_CONTROL is a
partition-wide MSR and it doesn't matter which particular CPU will be
used to receive reenlightenment notifications. The only real problem can
(in theory) be observed if the CPU whose id was acquired with
smp_processor_id() goes offline before we manage to write to the MSR,
the logic in hv_cpu_die() won't be able to reassign it correctly.
Reported-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Link: https://lore.kernel.org/r/20211012155005.1613352-1-vkuznets@redhat.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a27ca3947 ]
For packets originating from hardware scan, the channel and band is
included in the buffer descriptor (bd->rf_band & bd->rx_ch).
For 2Ghz band the channel value is directly reported in the 4-bit
rx_ch field. For 5Ghz band, the rx_ch field contains a mapping
index (given the 4-bit limitation).
The reserved0 value field is also used to extend 4-bit mapping to
5-bit mapping to support more than 16 5Ghz channels.
This change adds correct reporting of the frequency/band, that is
used in scan mechanism. And is required for 5Ghz hardware scan
support.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634554678-7993-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ef9dc0f14 ]
We got the following lockdep splat while running fstests (specifically
btrfs/003 and btrfs/020 in a row) with the new rc. This was uncovered
by 87579e9b7d ("loop: use worker per cgroup instead of kworker") which
converted loop to using workqueues, which comes with lockdep
annotations that don't exist with kworkers. The lockdep splat is as
follows:
WARNING: possible circular locking dependency detected
5.14.0-rc2-custom+ #34 Not tainted
------------------------------------------------------
losetup/156417 is trying to acquire lock:
ffff9c7645b02d38 ((wq_completion)loop0){+.+.}-{0:0}, at: flush_workqueue+0x84/0x600
but task is already holding lock:
ffff9c7647395468 (&lo->lo_mutex){+.+.}-{3:3}, at: __loop_clr_fd+0x41/0x650 [loop]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #5 (&lo->lo_mutex){+.+.}-{3:3}:
__mutex_lock+0xba/0x7c0
lo_open+0x28/0x60 [loop]
blkdev_get_whole+0x28/0xf0
blkdev_get_by_dev.part.0+0x168/0x3c0
blkdev_open+0xd2/0xe0
do_dentry_open+0x163/0x3a0
path_openat+0x74d/0xa40
do_filp_open+0x9c/0x140
do_sys_openat2+0xb1/0x170
__x64_sys_openat+0x54/0x90
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
-> #4 (&disk->open_mutex){+.+.}-{3:3}:
__mutex_lock+0xba/0x7c0
blkdev_get_by_dev.part.0+0xd1/0x3c0
blkdev_get_by_path+0xc0/0xd0
btrfs_scan_one_device+0x52/0x1f0 [btrfs]
btrfs_control_ioctl+0xac/0x170 [btrfs]
__x64_sys_ioctl+0x83/0xb0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
-> #3 (uuid_mutex){+.+.}-{3:3}:
__mutex_lock+0xba/0x7c0
btrfs_rm_device+0x48/0x6a0 [btrfs]
btrfs_ioctl+0x2d1c/0x3110 [btrfs]
__x64_sys_ioctl+0x83/0xb0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
-> #2 (sb_writers#11){.+.+}-{0:0}:
lo_write_bvec+0x112/0x290 [loop]
loop_process_work+0x25f/0xcb0 [loop]
process_one_work+0x28f/0x5d0
worker_thread+0x55/0x3c0
kthread+0x140/0x170
ret_from_fork+0x22/0x30
-> #1 ((work_completion)(&lo->rootcg_work)){+.+.}-{0:0}:
process_one_work+0x266/0x5d0
worker_thread+0x55/0x3c0
kthread+0x140/0x170
ret_from_fork+0x22/0x30
-> #0 ((wq_completion)loop0){+.+.}-{0:0}:
__lock_acquire+0x1130/0x1dc0
lock_acquire+0xf5/0x320
flush_workqueue+0xae/0x600
drain_workqueue+0xa0/0x110
destroy_workqueue+0x36/0x250
__loop_clr_fd+0x9a/0x650 [loop]
lo_ioctl+0x29d/0x780 [loop]
block_ioctl+0x3f/0x50
__x64_sys_ioctl+0x83/0xb0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
other info that might help us debug this:
Chain exists of:
(wq_completion)loop0 --> &disk->open_mutex --> &lo->lo_mutex
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&lo->lo_mutex);
lock(&disk->open_mutex);
lock(&lo->lo_mutex);
lock((wq_completion)loop0);
*** DEADLOCK ***
1 lock held by losetup/156417:
#0: ffff9c7647395468 (&lo->lo_mutex){+.+.}-{3:3}, at: __loop_clr_fd+0x41/0x650 [loop]
stack backtrace:
CPU: 8 PID: 156417 Comm: losetup Not tainted 5.14.0-rc2-custom+ #34
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
Call Trace:
dump_stack_lvl+0x57/0x72
check_noncircular+0x10a/0x120
__lock_acquire+0x1130/0x1dc0
lock_acquire+0xf5/0x320
? flush_workqueue+0x84/0x600
flush_workqueue+0xae/0x600
? flush_workqueue+0x84/0x600
drain_workqueue+0xa0/0x110
destroy_workqueue+0x36/0x250
__loop_clr_fd+0x9a/0x650 [loop]
lo_ioctl+0x29d/0x780 [loop]
? __lock_acquire+0x3a0/0x1dc0
? update_dl_rq_load_avg+0x152/0x360
? lock_is_held_type+0xa5/0x120
? find_held_lock.constprop.0+0x2b/0x80
block_ioctl+0x3f/0x50
__x64_sys_ioctl+0x83/0xb0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f645884de6b
Usually the uuid_mutex exists to protect the fs_devices that map
together all of the devices that match a specific uuid. In rm_device
we're messing with the uuid of a device, so it makes sense to protect
that here.
However in doing that it pulls in a whole host of lockdep dependencies,
as we call mnt_may_write() on the sb before we grab the uuid_mutex, thus
we end up with the dependency chain under the uuid_mutex being added
under the normal sb write dependency chain, which causes problems with
loop devices.
We don't need the uuid mutex here however. If we call
btrfs_scan_one_device() before we scratch the super block we will find
the fs_devices and not find the device itself and return EBUSY because
the fs_devices is open. If we call it after the scratch happens it will
not appear to be a valid btrfs file system.
We do not need to worry about other fs_devices modifying operations here
because we're protected by the exclusive operations locking.
So drop the uuid_mutex here in order to fix the lockdep splat.
A more detailed explanation from the discussion:
We are worried about rm and scan racing with each other, before this
change we'll zero the device out under the UUID mutex so when scan does
run it'll make sure that it can go through the whole device scan thing
without rm messing with us.
We aren't worried if the scratch happens first, because the result is we
don't think this is a btrfs device and we bail out.
The only case we are concerned with is we scratch _after_ scan is able
to read the superblock and gets a seemingly valid super block, so lets
consider this case.
Scan will call device_list_add() with the device we're removing. We'll
call find_fsid_with_metadata_uuid() and get our fs_devices for this
UUID. At this point we lock the fs_devices->device_list_mutex. This is
what protects us in this case, but we have two cases here.
1. We aren't to the device removal part of the RM. We found our device,
and device name matches our path, we go down and we set total_devices
to our super number of devices, which doesn't affect anything because
we haven't done the remove yet.
2. We are past the device removal part, which is protected by the
device_list_mutex. Scan doesn't find the device, it goes down and
does the
if (fs_devices->opened)
return -EBUSY;
check and we bail out.
Nothing about this situation is ideal, but the lockdep splat is real,
and the fix is safe, tho admittedly a bit scary looking.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ copy more from the discussion ]
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44bee215f7 ]
Fix a warning reported by smatch that ret could be returned without
initialized. The dedupe operations are supposed to to return 0 for a 0
length range but the caller does not pass olen == 0. To keep this
behaviour and also fix the warning initialize ret to 0.
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Sidong Yang <realwakka@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d730ee686 ]
Let GK45 not go into BIOS for determining the AC power state.
The BIOS wrongly returns 0, so hardcode the power state to 1.
The mini PC GK45 by Besstar Tech Lld. (aka Kodlix) just runs
off AC. It does not include any batteries. Nevertheless BIOS
reports AC off:
root@kodlix:/usr/src/linux# cat /sys/class/power_supply/ADP1/online
0
root@kodlix:/usr/src/linux# modprobe acpi_dbg
root@kodlix:/usr/src/linux# tools/power/acpi/acpidbg
- find _PSR
\_SB.PCI0.SBRG.H_EC.ADP1._PSR Method 000000009283cee8 001 Args 0 Len 001C Aml 00000000f54e5f67
- execute \_SB.PCI0.SBRG.H_EC.ADP1._PSR
Evaluating \_SB.PCI0.SBRG.H_EC.ADP1._PSR
Evaluation of \_SB.PCI0.SBRG.H_EC.ADP1._PSR returned object 00000000dc08c187, external buffer length 18
[Integer] = 0000000000000000
that should be
[Integer] = 0000000000000001
Signed-off-by: Stefan Schaeckeler <schaecsn@gmx.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c9c296adf ]
The VRF driver invokes netfilter for output+postrouting hooks so that users
can create rules that check for 'oif $vrf' rather than lower device name.
This is a problem when NAT rules are configured.
To avoid any conntrack involvement in round 1, tag skbs as 'untracked'
to prevent conntrack from picking them up.
This gets cleared before the packet gets handed to the ip stack so
conntrack will be active on the second iteration.
One remaining issue is that a rule like
output ... oif $vrfname notrack
won't propagate to the second round because we can't tell
'notrack set via ruleset' and 'notrack set by vrf driver' apart.
However, this isn't a regression: the 'notrack' removal happens
instead of unconditional nf_reset_ct().
I'd also like to avoid leaking more vrf specific conditionals into the
netfilter infra.
For ingress, conntrack has already been done before the packet makes it
to the vrf driver, with this patch egress does connection tracking with
lower/physical device as well.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 345dac33f5 ]
When configuring the kernel for big-endian, we set either BE-8 or BE-32
based on the CPU architecture level. Until linux-4.4, we did not have
any ARMv7-M platform allowing big-endian builds, but now i.MX/Vybrid
is in that category, adn we get a build error because of this:
arch/arm/kernel/module-plts.c: In function 'get_module_plt':
arch/arm/kernel/module-plts.c:60:46: error: implicit declaration of function '__opcode_to_mem_thumb32' [-Werror=implicit-function-declaration]
This comes down to picking the wrong default, ARMv7-M uses BE8
like ARMv7-A does. Changing the default gets the kernel to compile
and presumably works.
https://lore.kernel.org/all/1455804123-2526139-2-git-send-email-arnd@arndb.de/
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7427f3bb49 ]
So far, glock_hash_walk took a reference on each glock it iterated over, and it
was the examiner's responsibility to drop those references. Dropping the final
reference to a glock can sleep and the examiners are called in a RCU critical
section with spin locks held, so examiners that didn't need the extra reference
had to drop it asynchronously via gfs2_glock_queue_put or similar. This wasn't
done correctly in thaw_glock which did call gfs2_glock_put, and not at all in
dump_glock_func.
Change glock_hash_walk to not take glock references at all. That way, the
examiners that don't need them won't have to bother with slow asynchronous
puts, and the examiners that do need references can take them themselves.
Reported-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 486408d690 ]
In gfs2_inode_lookup and gfs2_create_inode, we're calling
gfs2_cancel_delete_work which currently cancels any remote delete work
(delete_work_func) synchronously. This means that if the work is
currently running, it will wait for it to finish. We're doing this to
pevent a previous instance of an inode from having any influence on the
next instance.
However, delete_work_func uses gfs2_inode_lookup internally, and we can
end up in a deadlock when delete_work_func gets interrupted at the wrong
time. For example,
(1) An inode's iopen glock has delete work queued, but the inode
itself has been evicted from the inode cache.
(2) The delete work is preempted before reaching gfs2_inode_lookup.
(3) Another process recreates the inode (gfs2_create_inode). It tries
to cancel any outstanding delete work, which blocks waiting for
the ongoing delete work to finish.
(4) The delete work calls gfs2_inode_lookup, which blocks waiting for
gfs2_create_inode to instantiate and unlock the new inode =>
deadlock.
It turns out that when the delete work notices that its inode has been
re-instantiated, it will do nothing. This means that it's safe to
cancel the delete work asynchronously. This prevents the kind of
deadlock described above.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61e18ce734 ]
When addr_gen_mode is set to IN6_ADDR_GEN_MODE_NONE, the link-local addr
should not be generated. But it isn't the case for GRE (as well as GRE6)
and SIT tunnels. Make it so that tunnels consider the addr_gen_mode,
especially for IN6_ADDR_GEN_MODE_NONE.
Do this in add_v4_addrs() to cover both GRE and SIT only if the addr
scope is link.
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Acked-by: Antonio Quartulli <a@unstable.cc>
Link: https://lore.kernel.org/r/20211020200618.467342-1-ssuryaextr@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3ea5d56f2 ]
Currently the stacktrace on clang compiled arm kernel uses the 'lr'
register to find the first frame address from pt_regs. However, that
is wrong after calling another function, because the 'lr' register
is used by 'bl' instruction and never be recovered.
As same as gcc arm kernel, directly use the frame pointer (r11) of
the pt_regs to find the first frame address.
Note that this fixes kretprobe stacktrace issue only with
CONFIG_UNWINDER_FRAME_POINTER=y. For the CONFIG_UNWINDER_ARM,
we need another fix.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3867ab592 ]
get_warnings_count() does fclose() using File * returned from popen().
Fix it to call pclose() as it should.
tools/testing/selftests/kvm/x86_64/mmio_warning_test
x86_64/mmio_warning_test.c: In function ‘get_warnings_count’:
x86_64/mmio_warning_test.c:87:9: warning: ‘fclose’ called on pointer returned from a mismatched allocation function [-Wmismatched-dealloc]
87 | fclose(f);
| ^~~~~~~~~
x86_64/mmio_warning_test.c:84:13: note: returned from ‘popen’
84 | f = popen("dmesg | grep \"WARNING:\" | wc -l", "r");
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b81a5f015 ]
When reading the partition table on initial scan hits an I/O error the
I/O will hang with the scan_mutex held:
[<0>] do_read_cache_page+0x49b/0x790
[<0>] read_part_sector+0x39/0xe0
[<0>] read_lba+0xf9/0x1d0
[<0>] efi_partition+0xf1/0x7f0
[<0>] bdev_disk_changed+0x1ee/0x550
[<0>] blkdev_get_whole+0x81/0x90
[<0>] blkdev_get_by_dev+0x128/0x2e0
[<0>] device_add_disk+0x377/0x3c0
[<0>] nvme_mpath_set_live+0x130/0x1b0 [nvme_core]
[<0>] nvme_mpath_add_disk+0x150/0x160 [nvme_core]
[<0>] nvme_alloc_ns+0x417/0x950 [nvme_core]
[<0>] nvme_validate_or_alloc_ns+0xe9/0x1e0 [nvme_core]
[<0>] nvme_scan_work+0x168/0x310 [nvme_core]
[<0>] process_one_work+0x231/0x420
and trying to delete the controller will deadlock as it tries to grab
the scan mutex:
[<0>] nvme_mpath_clear_ctrl_paths+0x25/0x80 [nvme_core]
[<0>] nvme_remove_namespaces+0x31/0xf0 [nvme_core]
[<0>] nvme_do_delete_ctrl+0x4b/0x80 [nvme_core]
As we're now properly ordering the namespace list there is no need to
hold the scan_mutex in nvme_mpath_clear_ctrl_paths() anymore.
And we always need to kick the requeue list as the path will be marked
as unusable and I/O will be requeued _without_ a current path.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2351ead99c ]
When removing a port, all its controllers are being removed, but there
are queues on the port that doesn't belong to any controller (during
connection time). This causes a use-after-free bug for any command
that dereferences req->port (like in nvmet_alloc_ctrl). Those queues
should be destroyed before freeing the port via configfs. Destroy
the remaining queues after the accept_work was cancelled guarantees
that no new queue will be created.
Signed-off-by: Israel Rukshin <israelr@nvidia.com>
Reviewed-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fcf73a804c ]
When removing a port, all its controllers are being removed, but there
are queues on the port that doesn't belong to any controller (during
connection time). This causes a use-after-free bug for any command
that dereferences req->port (like in nvmet_alloc_ctrl). Those queues
should be destroyed before freeing the port via configfs. Destroy the
remaining queues after the RDMA-CM was destroyed guarantees that no
new queue will be created.
Signed-off-by: Israel Rukshin <israelr@nvidia.com>
Reviewed-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3e19dcc4c ]
When a port is removed through configfs, any connected controllers
are starting teardown flow asynchronously and can still send commands.
This causes a use-after-free bug for any command that dereferences
req->port (like in nvmet_parse_io_cmd).
To fix this, wait for all the teardown scheduled works to complete
(like release_work at rdma/tcp drivers). This ensures there are no
active controllers when the port is eventually removed.
Signed-off-by: Israel Rukshin <israelr@nvidia.com>
Reviewed-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ecda6393d ]
The mailbox is initialized after the interrupt handler is installed. As
the firmware is loaded and started even later, it should not happen that
the interrupt occurs without the mailbox being initialized.
As the Linux Driver Verification project (linuxtesting.org) keeps
reporting this as an error, add a check to ignore interrupts before the
mailbox is initialized to fix this potential null pointer dereference.
Reported-by: Yuri Savinykh <s02190703@gse.cs.msu.ru>
Reported-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 037057a5a9 ]
This check is meant to catch cases where a requeue is attempted on a
request that is still inserted. It's never really been useful to catch any
misuse, and now it's actively wrong. Outside of that, this should not be a
BUG_ON() to begin with.
Remove the check as it's now causing active harm, as requeue off the plug
path will trigger it even though the request state is just fine.
Reported-by: Yi Zhang <yi.zhang@redhat.com>
Link: https://lore.kernel.org/linux-block/CAHj4cs80zAUc2grnCZ015-2Rvd-=gXRfB_dFKy=RTm+wRo09HQ@mail.gmail.com/
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ce1bb83a1 ]
If CONFIG_CFI_CLANG=y, attempting to read an event histogram will cause
the kernel to panic due to failed CFI check.
1. echo 'hist:keys=common_pid' >> events/sched/sched_switch/trigger
2. cat events/sched/sched_switch/hist
3. kernel panics on attempting to read hist
This happens because the sort() function expects a generic
int (*)(const void *, const void *) pointer for the compare function.
To prevent this CFI failure, change tracing map cmp_entries_* function
signatures to match this.
Also, fix the build error reported by the kernel test robot [1].
[1] https://lore.kernel.org/r/202110141140.zzi4dRh4-lkp@intel.com/
Link: https://lkml.kernel.org/r/20211014045217.3265162-1-kaleshsingh@google.com
Signed-off-by: Kalesh Singh <kaleshsingh@google.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d25302e465 ]
Some unfriendly component, such as dpdk, write the same mask to
unbound kworker cpumask again and again. Every time it write to
this interface some work is queue to cpu, even though the mask
is same with the original mask.
So, fix it by return success and do nothing if the cpumask is
equal with the old one.
Signed-off-by: Mengen Sun <mengensun@tencent.com>
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f8d7abaa4 ]
This might matter, for example, if the underlying type of enum xz_check
was a signed char. In such a case the validation wouldn't have caught an
unsupported header. I don't know if this problem can occur in the kernel
on any arch but it's still good to fix it because some people might copy
the XZ code to their own projects from Linux instead of the upstream
XZ Embedded repository.
This change may increase the code size by a few bytes. An alternative
would have been to use an unsigned int instead of enum xz_check but
using an enumeration looks cleaner.
Link: https://lore.kernel.org/r/20211010213145.17462-3-xiang@kernel.org
Signed-off-by: Lasse Collin <lasse.collin@tukaani.org>
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83d3c4f22a ]
With valid files, the safety margin described in lib/decompress_unxz.c
ensures that these buffers cannot overlap. But if the uncompressed size
of the input is larger than the caller thought, which is possible when
the input file is invalid/corrupt, the buffers can overlap. Obviously
the result will then be garbage (and usually the decoder will return
an error too) but no other harm will happen when such an over-run occurs.
This change only affects uncompressed LZMA2 chunks and so this
should have no effect on performance.
Link: https://lore.kernel.org/r/20211010213145.17462-2-xiang@kernel.org
Signed-off-by: Lasse Collin <lasse.collin@tukaani.org>
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b9e2291e3 ]
When the in memory flag is changed, we need to persist the change in the
rdev superblock flags. This is needed for "writemostly" and "failfast".
Reviewed-by: Li Feng <fengli@smartx.com>
Signed-off-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba0ffdd8ce ]
Particularly for NVMe with efficient deferred submission for many
requests, there are nice benefits to be seen by bumping the default max
plug count from 16 to 32. This is especially true for virtualized setups,
where the submit part is more expensive. But can be noticed even on
native hardware.
Reduce the multiple queue factor from 4 to 2, since we're changing the
default size.
While changing it, move the defines into the block layer private header.
These aren't values that anyone outside of the block layer uses, or
should use.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 67ca5159db ]
It seems reasonable to fine-tune only some of the skew values when using
one of the rgmii-*id PHY modes, and even when all skew values are
specified, using the correct ID PHY mode makes sense for documentation
purposes. Such a configuration also appears in the binding docs in
Documentation/devicetree/bindings/net/micrel-ksz90x1.txt, so the driver
should not warn about it.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20211012103402.21438-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2835f327bd ]
Some buggy firmware and/or brand new batteries can support a charge that's
slightly over the reported design capacity. In such cases, the kernel will
report to userspace that the charging state of the battery is "Unknown",
when in reality the battery charge is "Full", at least from the design
capacity point of view. Make the fallback condition accepts capacities
over the designed capacity so userspace knows that is full.
Signed-off-by: André Almeida <andrealmeid@collabora.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 814a66741b ]
Both iov_iter_get_pages and iov_iter_get_pages_alloc return the number
of bytes of the iovec they could get the pages for. When they cannot
get any pages, they're supposed to return 0, but when the start of the
iovec isn't page aligned, the calculation goes wrong and they return a
negative value. Fix both functions.
In addition, change iov_iter_get_pages_alloc to return NULL in that case
to prevent resource leaks.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8105c2abbf ]
The issue happens in several error handling paths on two refcounted
object related to the object "host" (dma_chan_rx, dma_chan_tx). In
these paths, the function forgets to decrement one or both objects'
reference count increased earlier by dma_request_chan(), causing
reference count leaks.
Fix it by balancing the refcounts of both objects in some error
handling paths. In correspondence with the changes in moxart_probe(),
IS_ERR() is replaced with IS_ERR_OR_NULL() in moxart_remove() as well.
Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn>
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Link: https://lore.kernel.org/r/20211009041918.28419-1-xiongx18@fudan.edu.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b6012a783 ]
kzalloc() is used to allocate memory for cd->detectors, and if it fails,
channel_detector_exit() behind the label fail will be called:
channel_detector_exit(dpd, cd);
In channel_detector_exit(), cd->detectors is dereferenced through:
struct pri_detector *de = cd->detectors[i];
To fix this possible null-pointer dereference, check cd->detectors before
the for loop to dereference cd->detectors.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Tuo Li <islituo@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210805153854.154066-1-islituo@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49d67e4457 ]
The tracefs file system is by default mounted such that only root user can
access it. But there are legitimate reasons to create a group and allow
those added to the group to have access to tracing. By changing the
permissions of the tracefs mount point to allow access, it will allow
group access to the tracefs directory.
There should not be any real reason to allow all access to the tracefs
directory as it contains sensitive information. Have the default
permission of directories being created not have any OTH (other) bits set,
such that an admin that wants to give permission to a group has to first
disable all OTH bits in the file system.
Link: https://lkml.kernel.org/r/20210818153038.664127804@goodmis.org
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 146e5e7333 ]
Due to deadlocks in the networking subsystem spotted 12 years ago[1],
a workaround was put in place[2] to avoid taking the rtnl lock when it
was not available and restarting the syscall (back to VFS, letting
userspace spin). The following construction is found a lot in the net
sysfs and sysctl code:
if (!rtnl_trylock())
return restart_syscall();
This can be problematic when multiple userspace threads use such
interfaces in a short period, making them to spin a lot. This happens
for example when adding and moving virtual interfaces: userspace
programs listening on events, such as systemd-udevd and NetworkManager,
do trigger actions reading files in sysfs. It gets worse when a lot of
virtual interfaces are created concurrently, say when creating
containers at boot time.
Returning early without hitting the above pattern when the syscall will
fail eventually does make things better. While it is not a fix for the
issue, it does ease things.
[1] https://lore.kernel.org/netdev/49A4D5D5.5090602@trash.net/https://lore.kernel.org/netdev/m14oyhis31.fsf@fess.ebiederm.org/
and https://lore.kernel.org/netdev/20090226084924.16cb3e08@nehalam/
[2] Rightfully, those deadlocks are *hard* to solve.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea2b9a3371 ]
bus_info field had a different value for the media entity and the video
device.
Fixes v4l2-compliance:
v4l2-compliance.cpp(637): media bus_info 'PCI:0000:00:05.0' differs from
V4L2 bus_info 'PCI:viewfinder'
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 553481e380 ]
For a try_fmt call, the node noes not need to be enabled.
Fixes v4l2-compliance
fail: v4l2-test-formats.cpp(717): Video Output Multiplanar is valid, but
no TRY_FMT was implemented
test VIDIOC_TRY_FMT: FAIL
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3c4b6f64a ]
ACPICA commit 0762982923f95eb652cf7ded27356b247c9774de
During wakeup from system-wide sleep states, acpi_get_sleep_type_data()
is called and it tries to get memory from the slab allocator in order
to evaluate a control method, but if KFENCE is enabled in the kernel,
the memory allocation attempt causes an IRQ work to be queued and a
self-IPI to be sent to the CPU running the code which requires the
memory controller to be ready, so if that happens too early in the
wakeup path, it doesn't work.
Prevent that from taking place by calling acpi_get_sleep_type_data()
for S0 upfront, when preparing to enter a given sleep state, and
saving the data obtained by it for later use during system wakeup.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214271
Reported-by: Reik Keutterling <spielkind@gmail.com>
Tested-by: Reik Keutterling <spielkind@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a130e8fbc7 ]
/proc/uptime reports idle time by reading the CPUTIME_IDLE field from
the per-cpu kcpustats. However, on NO_HZ systems, idle time is not
continually updated on idle cpus, leading this value to appear
incorrectly small.
/proc/stat performs an accounting update when reading idle time; we
can use the same approach for uptime.
With this patch, /proc/stat and /proc/uptime now agree on idle time.
Additionally, the following shows idle time tick up consistently on an
idle machine:
(while true; do cat /proc/uptime; sleep 1; done) | awk '{print $2-prev; prev=$2}'
Reported-by: Luigi Rizzo <lrizzo@google.com>
Signed-off-by: Josh Don <joshdon@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lkml.kernel.org/r/20210827165438.3280779-1-joshdon@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b36eb5e7b7 ]
Don't do kfree or other risky things when oops_in_progress is set.
It's easy enough to avoid doing them
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc41665498 ]
If rcsi2_code_to_fmt() return NULL, then null pointer dereference occurs
in the next cycle. That should not be possible now but adding checking
protects from future bugs.
The patch adds checking if format is NULL.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49c3eb3036 ]
The Cyberbook T116 tablet contains quite generic names in the sys_vendor
and product_name DMI strings, without this patch brcmfmac will try to load:
"brcmfmac43455-sdio.Default string-Default string.txt" as nvram file which
is way too generic.
The nvram file shipped on the factory Android image contains the exact
same settings as those used on the AcePC T8 mini PC, so point the new
DMI nvram filename quirk to the acepc-t8 nvram file.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210928160633.96928-1-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c15b5fc054 ]
When CONFIG_PRINTK is not set, the CMPXCHG_BUGCHECK() macro calls
_printk(), but _printk() is a static inline function, not available
as an extern.
Since the purpose of the macro is to print the BUGCHECK info,
make this config option depend on PRINTK.
Fixes multiple occurrences of this build error:
../include/linux/printk.h:208:5: error: static declaration of '_printk' follows non-static declaration
208 | int _printk(const char *s, ...)
| ^~~~~~~
In file included from ../arch/ia64/include/asm/cmpxchg.h:5,
../arch/ia64/include/uapi/asm/cmpxchg.h:146:28: note: previous declaration of '_printk' with type 'int(const char *, ...)'
146 | extern int _printk(const char *fmt, ...);
Cc: linux-ia64@vger.kernel.org
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Chris Down <chris@chrisdown.name>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d0d779b21 ]
Some tools like v4l2-compliance let users select a media device based
on the bus_info string which can be quite convenient. Use a unique
string for that.
This also fixes the following v4l2-compliance warning:
warn: v4l2-test-media.cpp(52): empty bus_info
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdfaf4752e ]
If of_device_get_match_data() return NULL,
then null pointer dereference occurs in s5p_mfc_init_pm().
The patch adds checking if dev->variant is NULL.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8515965e5e ]
The variable pdev is assigned to dev->plat_dev, and dev->plat_dev is
checked in:
if (!dev->plat_dev)
This indicates both dev->plat_dev and pdev can be NULL. If so, the
function dev_err() is called to print error information.
dev_err(&pdev->dev, "No platform data specified\n");
However, &pdev->dev is an illegal address, and it is dereferenced in
dev_err().
To fix this possible null-pointer dereference, replace dev_err() with
mfc_err().
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Tuo Li <islituo@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3f60e7e1a ]
All the entities must have a unique name. We can have a descriptive and
unique name by appending the function and the entity->id.
This is even resilent to multi chain devices.
Fixes v4l2-compliance:
Media Controller ioctls:
fail: v4l2-test-media.cpp(205): v2_entity_names_set.find(key) != v2_entity_names_set.end()
test MEDIA_IOC_G_TOPOLOGY: FAIL
fail: v4l2-test-media.cpp(394): num_data_links != num_links
test MEDIA_IOC_ENUM_ENTITIES/LINKS: FAIL
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ffccdde5f0 ]
The device is doing something unexpected with the control. Either because
the protocol is not properly implemented or there has been a HW error.
Fixes v4l2-compliance:
Control ioctls (Input 0):
fail: v4l2-test-controls.cpp(448): s_ctrl returned an error (22)
test VIDIOC_G/S_CTRL: FAIL
fail: v4l2-test-controls.cpp(698): s_ext_ctrls returned an error (22)
test VIDIOC_G/S/TRY_EXT_CTRLS: FAIL
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 548fa43a58 ]
At the moment of enabling irq handling:
1922 ret = devm_request_threaded_irq(&pdev->dev, irq, dcmi_irq_callback,
1923 dcmi_irq_thread, IRQF_ONESHOT,
1924 dev_name(&pdev->dev), dcmi);
there is still uninitialized field sd_format of struct stm32_dcmi *dcmi.
If an interrupt occurs in the interval between the installation of the
interrupt handler and the initialization of this field, NULL pointer
dereference happens.
This field is dereferenced in the handler function without any check:
457 if (dcmi->sd_format->fourcc == V4L2_PIX_FMT_JPEG &&
458 dcmi->misr & IT_FRAME) {
The patch moves interrupt handler installation
after initialization of the sd_format field that happens in
dcmi_graph_notify_complete() via dcmi_set_default_fmt().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Dmitriy Ulitin <ulitin@ispras.ru>
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e16f5e39ac ]
There were several issues with handling errors in lm3554_probe():
- Probe did not set the error code when v4l2_ctrl_handler_init() failed.
- It intermixed gotos for handling errors of v4l2_ctrl_handler_init()
and media_entity_pads_init().
- It did not set the error code for failures of v4l2_ctrl_new_custom().
- Probe did not free resources in case of failures of
atomisp_register_i2c_module().
The patch fixes all these issues.
Found by Linux Driver Verification project (linuxtesting.org).
Link: https://lore.kernel.org/linux-media/20210810162943.19852-1-novikov@ispras.ru
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0961ba6dd2 ]
To prevent corrupted frames after starting and stopping the sensor its
datasheet specifies a specific pause sequence to follow:
Stopping:
Set Pause_Restart Bit -> Set Restart Bit -> Set Chip_Enable Off
Restarting:
Set Chip_Enable On -> Clear Pause_Restart Bit
The Restart Bit is cleared automatically and must not be cleared
manually as this would cause undefined behavior.
Signed-off-by: Dirk Bender <d.bender@phytec.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86a03dad0f ]
For fragmented packets, ath11k reassembles each fragment as a normal
packet and then reinjects it into HW ring. In this case, the DMA
direction should be DMA_TO_DEVICE, not DMA_FROM_DEVICE, otherwise
invalid payload will be reinjected to HW and then delivered to host.
What is more, since arbitrary memory could be allocated to the frame, we
don't know what kind of data is contained in the buffer reinjected.
Thus, as a bad result, private info may be leaked.
Note that this issue is only found on Intel platform.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916064617.20006-1-bqiang@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 441b3b5911 ]
When wlan interface is up, 11d scan is sent to the firmware, and the
firmware needs to spend couple of seconds to complete the 11d scan. If
immediately a normal scan from user space arrives to ath11k, then the
normal scan request is also sent to the firmware, but the scan started
event will be reported to ath11k until the 11d scan complete. When timed
out for the scan started in ath11k, ath11k stops the normal scan and the
firmware reports WMI_SCAN_EVENT_DEQUEUED to ath11k for the normal scan.
ath11k has no handler for the event and then timed out for the scan
completed in ath11k_scan_stop(), and ath11k prints the following error
message.
[ 1491.604750] ath11k_pci 0000:02:00.0: failed to receive scan abort comple: timed out
[ 1491.604756] ath11k_pci 0000:02:00.0: failed to stop scan: -110
[ 1491.604758] ath11k_pci 0000:02:00.0: failed to start hw scan: -110
Add a handler for WMI_SCAN_EVENT_DEQUEUED and then complete the scan to
get rid of the above error message.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914164226.38843-1-jouni@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69a0fcf8a9 ]
During firmware recovery, the default reg rules which are
received via WMI_REG_CHAN_LIST_CC_EVENT can overwrite
the currently configured user regd.
See below snap for example,
root@OpenWrt:/# iw reg get | grep country
country FR: DFS-ETSI
country FR: DFS-ETSI
country FR: DFS-ETSI
country FR: DFS-ETSI
root@OpenWrt:/# echo assert > /sys/kernel/debug/ath11k/ipq8074\ hw2.0/simulate_f
w_crash
<snip>
[ 5290.471696] ath11k c000000.wifi1: pdev 1 successfully recovered
root@OpenWrt:/# iw reg get | grep country
country FR: DFS-ETSI
country US: DFS-FCC
country US: DFS-FCC
country US: DFS-FCC
In the above, the user configured country 'FR' is overwritten
when the rules of default country 'US' are received and updated during
recovery. Hence avoid processing of these rules in general
during firmware recovery as they have been already applied during
driver registration or after last set user country is configured.
This scenario applies for both AP and STA devices basically because
cfg80211 is not aware of the recovery and only the driver recovers, but
changing or resetting of the reg domain during recovery is not needed so
as to continue with the configured regdomain currently in use.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01460-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-3-jouni@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f595d6a6c ]
fscrypt currently requires a 512-bit master key when AES-256-XTS is
used, since AES-256-XTS keys are 512-bit and fscrypt requires that the
master key be at least as long any key that will be derived from it.
However, this is overly strict because AES-256-XTS doesn't actually have
a 512-bit security strength, but rather 256-bit. The fact that XTS
takes twice the expected key size is a quirk of the XTS mode. It is
sufficient to use 256 bits of entropy for AES-256-XTS, provided that it
is first properly expanded into a 512-bit key, which HKDF-SHA512 does.
Therefore, relax the check of the master key size to use the security
strength of the derived key rather than the size of the derived key
(except for v1 encryption policies, which don't use HKDF).
Besides making things more flexible for userspace, this is needed in
order for the use of a KDF which only takes a 256-bit key to be
introduced into the fscrypt key hierarchy. This will happen with
hardware-wrapped keys support, as all known hardware which supports that
feature uses an SP800-108 KDF using AES-256-CMAC, so the wrapped keys
are wrapped 256-bit AES keys. Moreover, there is interest in fscrypt
supporting the same type of AES-256-CMAC based KDF in software as an
alternative to HKDF-SHA512. There is no security problem with such
features, so fix the key length check to work properly with them.
Reviewed-by: Paul Crowley <paulcrowley@google.com>
Link: https://lore.kernel.org/r/20210921030303.5598-1-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c606008b70 ]
When creating a new virtual interface in mwifiex_add_virtual_intf(), we
update our internal driver states like bss_type, bss_priority, bss_role
and bss_mode to reflect the mode the firmware will be set to.
When switching virtual interface mode using
mwifiex_init_new_priv_params() though, we currently only update bss_mode
and bss_role. In order for the interface mode switch to actually work,
we also need to update bss_type to its proper value, so do that.
This fixes a crash of the firmware (because the driver tries to execute
commands that are invalid in AP mode) when switching from station mode
to AP mode.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-9-verdre@v0yd.nl
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2e9666cdf ]
We currently handle changing from the P2P to the STATION virtual
interface type slightly different than changing from P2P to ADHOC: When
changing to STATION, we don't send the SET_BSS_MODE command. We do send
that command on all other type-changes though, and it probably makes
sense to send the command since after all we just changed our BSS_MODE.
Looking at prior changes to this part of the code, it seems that this is
simply a leftover from old refactorings.
Since sending the SET_BSS_MODE command is the only difference between
mwifiex_change_vif_to_sta_adhoc() and the current code, we can now use
mwifiex_change_vif_to_sta_adhoc() for both switching to ADHOC and
STATION interface type.
This does not fix any particular bug and just "looked right", so there's
a small chance it might be a regression.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-4-verdre@v0yd.nl
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit feab5bb8f1 ]
pdev_id in structure 'wmi_pdev_bss_chan_info_event' is wrongly placed
at the beginning. This causes invalid values in survey dump. Hence, align
the structure with the firmware.
Note: The firmware releases follow this order since the feature was
implemented. Also, it is not changing across the branches including
QCA6390.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Ritesh Singh <ritesi@codeaurora.org>
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210720214922.118078-3-jouni@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0db7c32ad3 ]
Early in debugging, it made some sense to differentiate the first
iteration from subsequent iterations, but now this just causes confusion.
This commit therefore moves the "set_tasks_gp_state(rtp, RTGS_WAIT_CBS)"
statement to the beginning of the "for" loop in rcu_tasks_kthread().
Reported-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e080f1775 ]
mq / mqprio make the default child qdiscs visible. They only do
so for the qdiscs which are within real_num_tx_queues when the
device is registered. Depending on order of calls in the driver,
or if user space changes config via ethtool -L the number of
qdiscs visible under tc qdisc show will differ from the number
of queues. This is confusing to users and potentially to system
configuration scripts which try to make sure qdiscs have the
right parameters.
Add a new Qdisc_ops callback and make relevant qdiscs TTRT.
Note that this uncovers the "shortcut" created by
commit 1f27cde313 ("net: sched: use pfifo_fast for non real queues")
The default child qdiscs beyond initial real_num_tx are always
pfifo_fast, no matter what the sysfs setting is. Fixing this
gets a little tricky because we'd need to keep a reference
on whatever the default qdisc was at the time of creation.
In practice this is likely an non-issue the qdiscs likely have
to be configured to non-default settings, so whatever user space
is doing such configuration can replace the pfifos... now that
it will see them.
Reported-by: Matthew Massey <matthewmassey@fb.com>
Reviewed-by: Dave Taht <dave.taht@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ca9ce2ba4 ]
Different SoCs have a different number of channels, e.g .:
* amazon-se has 10 channels,
* danube+ar9 have 20 channels,
* vr9 has 28 channels,
* ar10 has 24 channels.
We can read the ID register and, depending on the reported
number of channels, reset the appropriate number of channels.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c12aa581f6 ]
Reading the DMA registers immediately after the reset causes
Data Bus Error. Adding a small delay fixes this issue.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71921a9606 ]
rcutorture is generating some nesting scenarios that are not compatible on PREEMPT_RT.
For example:
preempt_disable();
rcu_read_lock_bh();
preempt_enable();
rcu_read_unlock_bh();
The problem here is that on PREEMPT_RT the bottom halves have to be
disabled and enabled in preemptible context.
Reorder locking: start with BH locking and continue with then with
disabling preemption or interrupts. In the unlocking do it reverse by
first enabling interrupts and preemption and BH at the very end.
Ensure that on PREEMPT_RT BH locking remains unchanged if in
non-preemptible context.
Link: https://lkml.kernel.org/r/20190911165729.11178-6-swood@redhat.com
Link: https://lkml.kernel.org/r/20210819182035.GF4126399@paulmck-ThinkPad-P17-Gen-1
Signed-off-by: Scott Wood <swood@redhat.com>
[bigeasy: Drop ATOM_BH, make it only about changing BH in atomic
context. Allow enabling RCU in IRQ-off section. Reword commit message.]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99c23da0ee ]
The sco_send_frame() also takes lock_sock() during memcpy_from_msg()
call that may be endlessly blocked by a task with userfaultd
technique, and this will result in a hung task watchdog trigger.
Just like the similar fix for hci_sock_sendmsg() in commit
92c685dc5de0 ("Bluetooth: reorganize functions..."), this patch moves
the memcpy_from_msg() out of lock_sock() for addressing the hang.
This should be the last piece for fixing CVE-2021-3640 after a few
already queued fixes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 820a2ab23d ]
2 improvements to the Lenovo Ideapad D330 panel-orientation quirks:
1. Some versions of the Lenovo Ideapad D330 have a DMI_PRODUCT_NAME of
"81H3" and others have "81MD". Testing has shown that the "81MD" also has
a 90 degree mounted panel. Drop the DMI_PRODUCT_NAME from the existing
quirk so that the existing quirk matches both variants.
2. Some of the Lenovo Ideapad D330 models have a HD (800x1280) screen
instead of a FHD (1200x1920) screen (both are mounted right-side-up) add
a second Lenovo Ideapad D330 quirk for the HD version.
Changes in v2:
- Add a new quirk for Lenovo Ideapad D330 models with a HD screen instead
of a FHD screen
Link: https://github.com/systemd/systemd/pull/18884
Acked-by: Simon Ser <contact@emersion.fr>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210530110428.12994-2-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f492283b15 ]
It is expected from the clients to follow the below steps on an imported
dmabuf fd:
a) dmabuf = dma_buf_get(fd) // Get the dmabuf from fd
b) dma_buf_attach(dmabuf); // Clients attach to the dmabuf
o Here the kernel does some slab allocations, say for
dma_buf_attachment and may be some other slab allocation in the
dmabuf->ops->attach().
c) Client may need to do dma_buf_map_attachment().
d) Accordingly dma_buf_unmap_attachment() should be called.
e) dma_buf_detach () // Clients detach to the dmabuf.
o Here the slab allocations made in b) are freed.
f) dma_buf_put(dmabuf) // Can free the dmabuf if it is the last
reference.
Now say an erroneous client failed at step c) above thus it directly
called dma_buf_put(), step f) above. Considering that it may be the last
reference to the dmabuf, buffer will be freed with pending attachments
left to the dmabuf which can show up as the 'memory leak'. This should
at least be reported as the WARN().
Signed-off-by: Charan Teja Reddy <charante@codeaurora.org>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1627043468-16381-1-git-send-email-charante@codeaurora.org
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0cf48167b8 upstream.
The gauge requires us to clear the status bits manually for some alerts
to be properly dismissed. Previously the IRQ was configured to react only
on falling edge, which wasn't technically correct (the ALRT line is active
low), but it had a happy side-effect of preventing interrupt storms
on uncleared alerts from happening.
Fixes: 7fbf6b731b ("power: supply: max17042: Do not enforce (incorrect) interrupt trigger type")
Cc: <stable@vger.kernel.org>
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9aaa81c336 upstream.
Chipidea core was calling the interrupt handler from non-IRQ context
with interrupts enabled, something which can lead to a deadlock if
there's an actual interrupt trying to take a lock that's already held
(e.g. the controller lock in udc_irq()).
Add a wrapper that can be used to fake interrupts instead of calling the
handler directly.
Fixes: 3ecb3e09b0 ("usb: chipidea: Use extcon framework for VBUS and ID detect")
Fixes: 876d4e1e82 ("usb: chipidea: core: add wakeup support for extcon")
Cc: Peter Chen <peter.chen@kernel.org>
Cc: stable@vger.kernel.org # 4.4
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211021083447.20078-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26df977a90 upstream.
The bindings file for this driver is defining the property as 'reg' but
the driver was reading it with the 'num' name. The bindings actually had
the 'num' property when added in
commit ea52c21268 ("dt-bindings: iio: dac: Add docs for AD5770R DAC")
and then changed it to 'reg' in
commit 2cf3818f18 ("dt-bindings: iio: dac: AD5570R fix bindings errors").
However, both these commits landed in v5.7 so the assumption is
that either 'num' is not being used or if it is, the validations were not
done.
Anyways, if someone comes back yelling about this, we might just support
both of the properties in the future. Not ideal, but that's life...
Fixes: 2cf3818f18 ("dt-bindings: iio: dac: AD5570R fix bindings errors")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210818080525.62790-1-nuno.sa@analog.com
Cc: Stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 558df982d4 upstream.
On success i2c_master_send() returns the number of bytes written. The
call from iio_write_channel_info(), however, expects the return value to
be zero on success.
This bug causes incorrect consumption of the sysfs buffer in
iio_write_channel_info(). When writing more than two characters to
out_voltage0_raw, the ad5446 write handler is called multiple times
causing unexpected behavior.
Fixes: 3ec36a2cf0 ("iio:ad5446: Add support for I2C based DACs")
Signed-off-by: Pekka Korpinen <pekka.korpinen@iki.fi>
Link: https://lore.kernel.org/r/20210929185755.2384-1-pekka.korpinen@iki.fi
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9bf3d20331 upstream.
The block number in the quota tree on disk should be smaller than the
v2_disk_dqinfo.dqi_blocks. If the quota file was corrupted, we may be
allocating an 'allocated' block and that would lead to a loop in a tree,
which will probably trigger oops later. This patch adds a check for the
block number in the quota tree to prevent such potential issue.
Link: https://lore.kernel.org/r/20211008093821.1001186-2-yi.zhang@huawei.com
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Cc: stable@kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84e1b4045d upstream.
Aardvark controller has something like config space of a Root Port
available at offset 0x0 of internal registers - these registers are used
for implementation of the emulated bridge.
The default value of Class Code of this bridge corresponds to a RAID Mass
storage controller, though. (This is probably intended for when the
controller is used as Endpoint.)
Change the Class Code to correspond to a PCI Bridge.
Add comment explaining this change.
Link: https://lore.kernel.org/r/20211028185659.20329-6-kabel@kernel.org
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 771153fc88 upstream.
From very vague, ambiguous and incomplete information from Marvell we
deduced that the 32-bit Aardvark register at address 0x4
(PCIE_CORE_CMD_STATUS_REG), which is not documented for Root Complex mode
in the Functional Specification (only for Endpoint mode), controls two
16-bit PCIe registers: Command Register and Status Registers of PCIe Root
Port.
This means that bit 2 controls bus mastering and forwarding of memory and
I/O requests in the upstream direction. According to PCI specifications
bits [0:2] of Command Register, this should be by default disabled on
reset. So explicitly disable these bits at early setup of the Aardvark
driver.
Remove code which unconditionally enables all 3 bits and let kernel code
(via pci_set_master() function) to handle bus mastering of Root PCIe
Bridge via emulated PCI_COMMAND on emulated bridge.
Link: https://lore.kernel.org/r/20211028185659.20329-5-kabel@kernel.org
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # b2a56469d5 ("PCI: aardvark: Add FIXME comment for PCIE_CORE_CMD_STATUS_REG access")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46ef6090db upstream.
Commit 366697018c ("PCI: aardvark: Add PHY support") introduced
configuration of PCIe Reference clock via PCIE_CORE_REF_CLK_REG register,
but did it incorrectly.
PCIe Reference clock differential pair is routed from system board to
endpoint card, so on CPU side it has output direction. Therefore it is
required to enable transmitting and disable receiving.
Default configuration according to Armada 3700 Functional Specifications is
enabled receiver part and disabled transmitter.
We need this change because otherwise PCIe Reference clock is configured to
some undefined state when differential pair is used for both transmitting
and receiving.
Fix this by disabling receiver part.
Link: https://lore.kernel.org/r/20211005180952.6812-6-kabel@kernel.org
Fixes: 366697018c ("PCI: aardvark: Add PHY support")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 661c399a65 upstream.
Current implementation of advk_pcie_link_up() is wrong as it marks also
link disabled or hot reset states as link up.
Fix it by marking link up only to those states which are defined in PCIe
Base specification 3.0, Table 4-14: Link Status Mapped to the LTSSM.
To simplify implementation, Define macros for every LTSSM state which
aardvark hardware can return in CFG_REG register.
Fix also checking for link training according to the same Table 4-14.
Define a new function advk_pcie_link_training() for this purpose.
Link: https://lore.kernel.org/r/20211005180952.6812-13-kabel@kernel.org
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Cc: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a7ca6d7fa3 upstream.
The PCIE_ISR1_REG says which interrupts are currently set / active,
including those which are masked.
The driver currently reads this register and looks if some unmasked
interrupts are active, and if not, it clears status bits of _all_
interrupts, including the masked ones.
This is incorrect, since, for example, some drivers may poll these bits.
Remove this clearing, and also remove this early return statement
completely, since it does not change functionality in any way.
Link: https://lore.kernel.org/r/20211005180952.6812-7-kabel@kernel.org
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a41ae80bd upstream.
The pci_bridge_emul_conf_write() function correctly clears W1C bits in
cfgspace cache, but it does not inform the underlying implementation
about the clear request: the .write_op() method is given the value with
these bits cleared.
This is wrong if the .write_op() needs to know which bits were requested
to be cleared.
Fix the value to be passed into the .write_op() method to have requested
W1C bits set, so that it can clear them.
Both pci-bridge-emul users (mvebu and aardvark) are compatible with this
change.
Link: https://lore.kernel.org/r/20211028185659.20329-2-kabel@kernel.org
Fixes: 23a5fba4d9 ("PCI: Introduce PCI bridge emulated config space common logic")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a25440376 upstream.
Example for triggering use after free in a overlay on ext4 setup:
aio_read
ovl_read_iter
vfs_iter_read
ext4_file_read_iter
ext4_dio_read_iter
iomap_dio_rw -> -EIOCBQUEUED
/*
* Here IO is completed in a separate thread,
* ovl_aio_cleanup_handler() frees aio_req which has iocb embedded
*/
file_accessed(iocb->ki_filp); /**BOOM**/
Fix by introducing a refcount in ovl_aio_req similarly to aio_kiocb. This
guarantees that iocb is only freed after vfs_read/write_iter() returns on
underlying fs.
Fixes: 2406a307ac ("ovl: implement async IO routines")
Signed-off-by: yangerkun <yangerkun@huawei.com>
Link: https://lore.kernel.org/r/20210930032228.3199690-3-yangerkun@huawei.com/
Cc: <stable@vger.kernel.org> # v5.6
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40fdea0284 upstream.
When running as PVH or HVM guest with actual memory < max memory the
hypervisor is using "populate on demand" in order to allow the guest
to balloon down from its maximum memory size. For this to work
correctly the guest must not touch more memory pages than its target
memory size as otherwise the PoD cache will be exhausted and the guest
is crashed as a result of that.
In extreme cases ballooning down might not be finished today before
the init process is started, which can consume lots of memory.
In order to avoid random boot crashes in such cases, add a late init
call to wait for ballooning down having finished for PVH/HVM guests.
Warn on console if initial ballooning fails, panic() after stalling
for more than 3 minutes per default. Add a module parameter for
changing this timeout.
[boris: replaced pr_info() with pr_notice()]
Cc: <stable@vger.kernel.org>
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20211102091944.17487-1-jgross@suse.com
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7444d706be upstream.
The driver no longer depends on this option, but it fails to
build if it's disabled because the skb->tc_skip_classify is
hidden behind an #ifdef:
drivers/net/ifb.c:81:8: error: no member named 'tc_skip_classify' in 'struct sk_buff'
skb->tc_skip_classify = 1;
Use the same #ifdef around the assignment.
Fixes: 046178e726 ("ifb: Depend on netfilter alternatively to tc")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 027b57170b upstream.
Since commit edc6afc549 ("tty: switch to ktermios and new framework")
termios speed is no longer stored only in c_cflag member but also in new
additional c_ispeed and c_ospeed members. If BOTHER flag is set in c_cflag
then termios speed is stored only in these new members.
Therefore to correctly restore termios speed it is required to store also
ispeed and ospeed members, not only cflag member.
In case only cflag member with BOTHER flag is restored then functions
tty_termios_baud_rate() and tty_termios_input_baud_rate() returns baudrate
stored in c_ospeed / c_ispeed member, which is zero as it was not restored
too. If reported baudrate is invalid (e.g. zero) then serial core functions
report fallback baudrate value 9600. So it means that in this case original
baudrate is lost and kernel changes it to value 9600.
Simple reproducer of this issue is to boot kernel with following command
line argument: "console=ttyXXX,86400" (where ttyXXX is the device name).
For speed 86400 there is no Bnnn constant and therefore kernel has to
represent this speed via BOTHER c_cflag. Which means that speed is stored
only in c_ospeed and c_ispeed members, not in c_cflag anymore.
If bootloader correctly configures serial device to speed 86400 then kernel
prints boot log to early console at speed speed 86400 without any issue.
But after kernel starts initializing real console device ttyXXX then speed
is changed to fallback value 9600 because information about speed was lost.
This patch fixes above issue by storing and restoring also ispeed and
ospeed members, which are required for BOTHER flag.
Fixes: edc6afc549 ("[PATCH] tty: switch to ktermios and new framework")
Cc: stable@vger.kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20211002130900.9518-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51d1579466 upstream.
The resetting of the entire ring buffer use to simply go through and reset
each individual CPU buffer that had its own protection and synchronization.
But this was very slow, due to performing a synchronization for each CPU.
The code was reshuffled to do one disabling of all CPU buffers, followed
by a single RCU synchronization, and then the resetting of each of the CPU
buffers. But unfortunately, the mutex that prevented multiple occurrences
of resetting the buffer was not moved to the upper function, and there is
nothing to protect from it.
Take the ring buffer mutex around the global reset.
Cc: stable@vger.kernel.org
Fixes: b23d7a5f4a ("ring-buffer: speed up buffer resets by avoiding synchronize_rcu for each CPU")
Reported-by: "Tzvetomir Stoyanov (VMware)" <tz.stoyanov@gmail.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7dfbc624eb upstream.
Check the current VMCS controls to determine if an MSR write will be
intercepted due to MSR bitmaps being disabled. In the nested VMX case,
KVM will disable MSR bitmaps in vmcs02 if they're disabled in vmcs12 or
if KVM can't map L1's bitmaps for whatever reason.
Note, the bad behavior is relatively benign in the current code base as
KVM sets all bits in vmcs02's MSR bitmap by default, clears bits if and
only if L0 KVM also disables interception of an MSR, and only uses the
buggy helper for MSR_IA32_SPEC_CTRL. Because KVM explicitly tests WRMSR
before disabling interception of MSR_IA32_SPEC_CTRL, the flawed check
will only result in KVM reading MSR_IA32_SPEC_CTRL from hardware when it
isn't strictly necessary.
Tag the fix for stable in case a future fix wants to use
msr_write_intercepted(), in which case a buggy implementation in older
kernels could prove subtly problematic.
Fixes: d28b387fb7 ("KVM/VMX: Allow direct access to MSR_IA32_SPEC_CTRL")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211109013047.2041518-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8bb084119f upstream.
Since ARMv8.0 the upper 32 bits of ESR_ELx have been RES0, and recently
some of the upper bits gained a meaning and can be non-zero. For
example, when FEAT_LS64 is implemented, ESR_ELx[36:32] contain ISS2,
which for an ST64BV or ST64BV0 can be non-zero. This can be seen in ARM
DDI 0487G.b, page D13-3145, section D13.2.37.
Generally, we must not rely on RES0 bit remaining zero in future, and
when extracting ESR_ELx.EC we must mask out all other bits.
All C code uses the ESR_ELx_EC() macro, which masks out the irrelevant
bits, and therefore no alterations are required to C code to avoid
consuming irrelevant bits.
In a couple of places the KVM assembly extracts ESR_ELx.EC using LSR on
an X register, and so could in theory consume previously RES0 bits. In
both cases this is for comparison with EC values ESR_ELx_EC_HVC32 and
ESR_ELx_EC_HVC64, for which the upper bits of ESR_ELx must currently be
zero, but this could change in future.
This patch adjusts the KVM vectors to use UBFX rather than LSR to
extract ESR_ELx.EC, ensuring these are robust to future additions to
ESR_ELx.
Cc: stable@vger.kernel.org
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Alexandru Elisei <alexandru.elisei@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211103110545.4613-1-mark.rutland@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 223a3b8283 upstream.
On Galaxy S3 (i9300/i9305), which has the max17047 fuel gauge and no
current sense resistor (rsns), the RepSOC register does not provide an
accurate state of charge value. The reported value is wrong, and does
not change over time. VFSOC however, which uses the voltage fuel gauge
to determine the state of charge, always shows an accurate value.
For devices without current sense, VFSOC is already used for the
soc-alert (0x0003 is written to MiscCFG register), so with this change
the source of the alert and the PROP_CAPACITY value match.
Fixes: 359ab9f5b1 ("power_supply: Add MAX17042 Fuel Gauge Driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Suggested-by: Wolfgang Wiedmeyer <wolfgit@wiedmeyer.de>
Signed-off-by: Henrik Grimler <henrik@grimler.se>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4ebddd654 upstream.
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: b36bf0a0fe ("mtd: rawnand: socrates: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-9-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc7e5940aa upstream.
In orininal code, use 2 function spin_lock() and local_irq_save() to
protect the critical zone. But when enable the kernel debug config,
there are below inconsistent lock state detected.
================================
WARNING: inconsistent lock state
5.10.63-yocto-standard #1 Not tainted
--------------------------------
inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
lock_torture_wr/226 [HC0[0]:SC1[5]:HE1:SE0] takes:
ffff002005b2dd80 (&p->access_spinlock){+.?.}-{3:3}, at: qbman_swp_enqueue_multiple_mem_back+0x44/0x270
{SOFTIRQ-ON-W} state was registered at:
lock_acquire.part.0+0xf8/0x250
lock_acquire+0x68/0x84
_raw_spin_lock+0x68/0x90
qbman_swp_enqueue_multiple_mem_back+0x44/0x270
......
cryptomgr_test+0x38/0x60
kthread+0x158/0x164
ret_from_fork+0x10/0x38
irq event stamp: 4498
hardirqs last enabled at (4498): [<ffff800010fcf980>] _raw_spin_unlock_irqrestore+0x90/0xb0
hardirqs last disabled at (4497): [<ffff800010fcffc4>] _raw_spin_lock_irqsave+0xd4/0xe0
softirqs last enabled at (4458): [<ffff8000100108c4>] __do_softirq+0x674/0x724
softirqs last disabled at (4465): [<ffff80001005b2a4>] __irq_exit_rcu+0x190/0x19c
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&p->access_spinlock);
<Interrupt>
lock(&p->access_spinlock);
*** DEADLOCK ***
So, in order to avoid deadlock, use the combined functions
spin_lock_irqsave/spin_unlock_irqrestore() to protect critical zone.
Fixes: 3b2abda7d2 ("soc: fsl: dpio: Replace QMAN array mode with ring mode enqueue")
Cc: stable@vger.kernel.org
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e775eb9fc2 upstream.
When enable debug kernel configs,there will be calltrace as below:
BUG: using smp_processor_id() in preemptible [00000000] code: swapper/0/1
caller is debug_smp_processor_id+0x20/0x30
CPU: 6 PID: 1 Comm: swapper/0 Not tainted 5.10.63-yocto-standard #1
Hardware name: NXP Layerscape LX2160ARDB (DT)
Call trace:
dump_backtrace+0x0/0x1a0
show_stack+0x24/0x30
dump_stack+0xf0/0x13c
check_preemption_disabled+0x100/0x110
debug_smp_processor_id+0x20/0x30
dpaa2_io_query_fq_count+0xdc/0x154
dpaa2_eth_stop+0x144/0x314
__dev_close_many+0xdc/0x160
__dev_change_flags+0xe8/0x220
dev_change_flags+0x30/0x70
ic_close_devs+0x50/0x78
ip_auto_config+0xed0/0xf10
do_one_initcall+0xac/0x460
kernel_init_freeable+0x30c/0x378
kernel_init+0x20/0x128
ret_from_fork+0x10/0x38
Based on comment in the context, it doesn't matter whether
preemption is disable or not. So, replace smp_processor_id()
with raw_smp_processor_id() to avoid above call trace.
Fixes: c89105c9b3 ("staging: fsl-mc: Move DPIO from staging to drivers/soc/fsl")
Cc: stable@vger.kernel.org
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95bf9d646c upstream.
When an instruction to save or restore a register from the stack fails
in _save_fp_context or _restore_fp_context return with -EFAULT. This
change was made to r2300_fpu.S[1] but it looks like it got lost with
the introduction of EX2[2]. This is also what the other implementation
of _save_fp_context and _restore_fp_context in r4k_fpu.S does, and
what is needed for the callers to be able to handle the error.
Furthermore calling do_exit(SIGSEGV) from bad_stack is wrong because
it does not terminate the entire process it just terminates a single
thread.
As the changed code was the only caller of arch/mips/kernel/syscall.c:bad_stack
remove the problematic and now unused helper function.
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Maciej Rozycki <macro@orcam.me.uk>
Cc: linux-mips@vger.kernel.org
[1] 35938a00ba ("MIPS: Fix ISA I FP sigcontext access violation handling")
[2] f92722dc45 ("MIPS: Correct MIPS I FP sigcontext layout")
Cc: stable@vger.kernel.org
Fixes: f92722dc45 ("MIPS: Correct MIPS I FP sigcontext layout")
Acked-by: Maciej W. Rozycki <macro@orcam.me.uk>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Link: https://lkml.kernel.org/r/20211020174406.17889-5-ebiederm@xmission.com
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fff53a551d upstream.
This patch fixes 2 problems:
[1] The output warning logs and data loss when performing
mount/umount then remount the device with jffs2 format.
[2] The access width of SMWDR[0:1]/SMRDR[0:1] register is wrong.
This is the sample warning logs when performing mount/umount then
remount the device with jffs2 format:
jffs2: jffs2_scan_inode_node(): CRC failed on node at 0x031c51d4:
Read 0x00034e00, calculated 0xadb272a7
The reason for issue [1] is that the writing data seems to
get messed up.
Data is only completed when the number of bytes is divisible by 4.
If you only have 3 bytes of data left to write, 1 garbage byte
is inserted after the end of the write stream.
If you only have 2 bytes of data left to write, 2 bytes of '00'
are added into the write stream.
If you only have 1 byte of data left to write, 2 bytes of '00'
are added into the write stream. 1 garbage byte is inserted after
the end of the write stream.
To solve problem [1], data must be written continuously in serial
and the write stream ends when data is out.
Following HW manual 62.2.15, access to SMWDR0 register should be
in the same size as the transfer size specified in the SPIDE[3:0]
bits in the manual mode enable setting register (SMENR).
Be sure to access from address 0.
So, in 16-bit transfer (SPIDE[3:0]=b'1100), SMWDR0 should be
accessed by 16-bit width.
Similar to SMWDR1, SMDDR0/1 registers.
In current code, SMWDR0 register is accessed by regmap_write()
that only set up to do 32-bit width.
To solve problem [2], data must be written 16-bit or 8-bit when
transferring 1-byte or 2-byte.
Fixes: ca7d8b980b ("memory: add Renesas RPC-IF driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Duc Nguyen <duc.nguyen.ub@renesas.com>
[wsa: refactored to use regmap only via reg_read/reg_write]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210922091007.5516-1-wsa+renesas@sang-engineering.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d613f9f72 upstream.
The existence of sigkill_pending is a little silly as it is
functionally a duplicate of fatal_signal_pending that is used in
exactly one place.
Checking for pending fatal signals and returning early in ptrace_stop
is actively harmful. It casues the ptrace_stop called by
ptrace_signal to return early before setting current->exit_code.
Later when ptrace_signal reads the signal number from
current->exit_code is undefined, making it unpredictable what will
happen.
Instead rely on the fact that schedule will not sleep if there is a
pending signal that can awaken a task.
Removing the explict sigkill_pending test fixes fixes ptrace_signal
when ptrace_stop does not stop because current->exit_code is always
set to to signr.
Cc: stable@vger.kernel.org
Fixes: 3d749b9e67 ("ptrace: simplify ptrace_stop()->sigkill_pending() path")
Fixes: 1a669c2f16 ("Add arch_ptrace_stop")
Link: https://lkml.kernel.org/r/87pmsyx29t.fsf@disp2133
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b515d09705 upstream.
P2P client mode was only working the first time.
On subsequent connection attempts the group was successfully created but
no data was sent (no transmitted data packets were seen with a sniffer).
The reason for this was that the hardware was being configured in fixed
rate mode with rate RSI_RATE_1 (1Mbps) which is not valid in the 5GHz band.
In P2P mode wpa_supplicant uses NL80211_CMD_SET_TX_BITRATE_MASK to disallow
the 11b rates in the 2.4GHz band which updated common->fixedrate_mask.
rsi_set_min_rate() then used the fixedrate_mask to calculate the minimum
allowed rate, or 0xffff = auto if none was found.
However that calculation did not account for the different rate sets
allowed in the different bands leading to the error.
Fixing set_min_rate() would result in 6Mb/s being used all the time
which is not what we want either.
The reason the problem did not occur on the first connection is that
rsi_mac80211_set_rate_mask() only updated the fixedrate_mask for
the *current* band. When it was called that was still 2.4GHz as the
switch is done later. So the when set_min_rate() was subsequently
called after the switch to 5GHz it still had a mask of zero, leading
to defaulting to auto mode.
Fix this by differentiating the case of a single rate being
requested, in which case the hardware will be used in fixed rate
mode with just that rate, and multiple rates being requested,
in which case we remain in auto mode but the firmware rate selection
algorithm is configured with a restricted set of rates.
Fixes: dad0d04fa7 ("rsi: Add RS9113 wireless driver")
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
CC: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630337206-12410-4-git-send-email-martin.fuzzey@flowbird.group
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 99ac601882 upstream.
My previous patch checked if encryption should be enabled by directly
checking info->control.hw_key (like the downstream driver).
However that missed that the control and driver_info members of
struct ieee80211_tx_info are union fields.
Due to this when rsi_core_xmit() updates fields in "tx_params"
(driver_info) it can overwrite the control.hw_key, causing the result
of the later test to be incorrect.
With the current structure layout the first byte of control.hw_key is
overlayed with the vap_id so, since we only test if control.hw_key is
NULL / non NULL, a non zero vap_id will incorrectly enable encryption.
In basic STA and AP modes the vap_id is always zero so it works but in
P2P client mode a second VIF is created causing vap_id to be non zero
and hence encryption to be enabled before keys have been set.
Fix this by extracting the key presence flag to a new field in the driver
private tx_params structure and populating it first.
Fixes: 314538041b ("rsi: fix AP mode with WPA failure due to encrypted EAPOL")
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
CC: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630337206-12410-3-git-send-email-martin.fuzzey@flowbird.group
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b14ed6e11 upstream.
When BT coexistence is enabled (eg oper mode 13, which is the default)
the initialisation on startup sometimes silently fails.
In a normal initialisation we see
usb 1-1.3: Product: Wireless USB Network Module
usb 1-1.3: Manufacturer: Redpine Signals, Inc.
usb 1-1.3: SerialNumber: 000000000001
rsi_91x: rsi_probe: Initialized os intf ops
rsi_91x: rsi_load_9116_firmware: Loading chunk 0
rsi_91x: rsi_load_9116_firmware: Loading chunk 1
rsi_91x: rsi_load_9116_firmware: Loading chunk 2
rsi_91x: Max Stations Allowed = 1
But sometimes the last log is missing and the wlan net device is
not created.
Running a userspace loop that resets the hardware via a GPIO shows the
problem occurring ~5/100 resets.
The problem does not occur in oper mode 1 (wifi only).
Adding logs shows that the initialisation state machine requests a MAC
reset via rsi_send_reset_mac() but the firmware does not reply, leading
to the initialisation sequence being incomplete.
Fix this by delaying attaching the BT adapter until the wifi
initialisation has completed.
With this applied I have done > 300 reset loops with no errors.
Fixes: 716b840c76 ("rsi: handle BT traffic in driver")
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
CC: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630337206-12410-2-git-send-email-martin.fuzzey@flowbird.group
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f971a85439 upstream.
Checking if DMA is enabled should be done via the
ata_dma_enabled helper function, since the init state
0xff indicates disabled.
This meant that ATA_CMD_READ_LOG_DMA_EXT was used and probed
for before DMA was enabled, which caused hangs for some combinations
of controllers and devices.
It might also have caused it to be incorrectly disabled as broken,
but there have been no reports of that.
Cc: stable@vger.kernel.org
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=195895
Signed-off-by: Reimar Döffinger <Reimar.Doeffinger@gmx.de>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e3e59c31f upstream.
It seems that the PCIe+USB firmware (latest version 15.68.19.p21) of the
88W8897 card sometimes ignores or misses when we try to wake it up by
writing to the firmware status register. This leads to the firmware
wakeup timeout expiring and the driver resetting the card because we
assume the firmware has hung up or crashed.
Turns out that the firmware actually didn't hang up, but simply "missed"
our wakeup request and didn't send us an interrupt with an AWAKE event.
Trying again to read the firmware status register after a short timeout
usually makes the firmware wake up as expected, so add a small retry
loop to mwifiex_pm_wakeup_card() that looks at the interrupt status to
check whether the card woke up.
The number of tries and timeout lengths for this were determined
experimentally: The firmware usually takes about 500 us to wake up
after we attempt to read the status register. In some cases where the
firmware is very busy (for example while doing a bluetooth scan) it
might even miss our requests for multiple milliseconds, which is why
after 15 tries the waiting time gets increased to 10 ms. The maximum
number of tries it took to wake the firmware when testing this was
around 20, so a maximum number of 50 tries should give us plenty of
safety margin.
Here's a reproducer for those firmware wakeup failures I've found:
1) Make sure wifi powersaving is enabled (iw dev wlp1s0 set power_save on)
2) Connect to any wifi network (makes firmware go into wifi powersaving
mode, not deep sleep)
3) Make sure bluetooth is turned off (to ensure the firmware actually
enters powersave mode and doesn't keep the radio active doing bluetooth
stuff)
4) To confirm that wifi powersaving is entered ping a device on the LAN,
pings should be a few ms higher than without powersaving
5) Run "while true; do iwconfig; sleep 0.0001; done", this wakes and
suspends the firmware extremely often
6) Wait until things explode, for me it consistently takes <5 minutes
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=109681
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011133224.15561-3-verdre@v0yd.nl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5f4eb8223 upstream.
On the 88W8897 PCIe+USB card the firmware randomly crashes after setting
the TX ring write pointer. The issue is present in the latest firmware
version 15.68.19.p21 of the PCIe+USB card.
Those firmware crashes can be worked around by reading any PCI register
of the card after setting that register, so read the PCI_VENDOR_ID
register here. The reason this works is probably because we keep the bus
from entering an ASPM state for a bit longer, because that's what causes
the cards firmware to crash.
This fixes a bug where during RX/TX traffic and with ASPM L1 substates
enabled (the specific substates where the issue happens appear to be
platform dependent), the firmware crashes and eventually a command
timeout appears in the logs.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=109681
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011133224.15561-2-verdre@v0yd.nl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 928265e360 upstream.
There is no reason to allow "syscore" devices to runtime-suspend
during system-wide PM transitions, because they are subject to the
same possible failure modes as any other devices in that respect.
Accordingly, change device_prepare() and device_complete() to call
pm_runtime_get_noresume() and pm_runtime_put(), respectively, for
"syscore" devices too.
Fixes: 057d51a126 ("Merge branch 'pm-sleep'")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: 3.10+ <stable@vger.kernel.org> # 3.10+
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3fd2c95c1 upstream.
We observe unexpected connection drops with some APs due to
non-acked mac80211 generated null data frames (keep-alive).
After debugging and capture, we noticed that null frames are
submitted at standard data bitrate and that the given APs are
in trouble with that.
After setting the null frame bitrate to control bitrate, all
null frames are acked as expected and connection is maintained.
Not sure if it's a requirement of the specification, but it seems
the right thing to do anyway, null frames are mostly used for control
purpose (power-saving, keep-alive...), and submitting them with
a slower/simpler bitrate/modulation is more robust.
Cc: stable@vger.kernel.org
Fixes: 512b191d96 ("wcn36xx: Fix TX data path")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634560399-15290-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a9e79b116c upstream.
This change fix the TX ack mechanism in various ways:
- For NO_ACK tagged packets, we don't need to wait for TX_ACK indication
and so are not subject to the single packet ack limitation. So we don't
have to stop the tx queue, and can call the tx status callback as soon
as DMA transfer has completed.
- Fix skb ownership/reference. Only start status indication timeout
once the DMA transfer has been completed. This avoids the skb to be
both referenced in the DMA tx ring and by the tx_ack_skb pointer,
preventing any use-after-free or double-free.
- This adds a sanity (paranoia?) check on the skb tx ack pointer.
- Resume TX queue if TX status tagged packet TX fails.
Cc: stable@vger.kernel.org
Fixes: fdf21cc371 ("wcn36xx: Add TX ack support")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634567281-28997-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 046178e726 upstream.
IFB originally depended on NET_CLS_ACT for traffic redirection.
But since v4.5, that may be achieved with NFT_FWD_NETDEV as well.
Fixes: 39e6dea28a ("netfilter: nf_tables: add forward expression to the netdev family")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v4.5+: bcfabee1af: netfilter: nft_fwd_netdev: allow to redirect to ifb via ingress
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a006acb931 upstream.
Add the missing endpoint max-packet sanity check to probe() to avoid
division by zero in ath10k_usb_hif_tx_sg() in case a malicious device
has broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4f ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: 4db66499df ("ath10k: add initial USB support")
Cc: stable@vger.kernel.org # 4.14
Cc: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027080819.6675-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1b9ca365d upstream.
Add the missing endpoint max-packet sanity check to probe() to avoid
division by zero in ath10k_usb_hif_tx_sg() in case a malicious device
has broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4f ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: 9cbee35868 ("ath6kl: add full USB support")
Cc: stable@vger.kernel.org # 3.5
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027080819.6675-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89f8765a11 upstream.
Add the missing endpoint sanity checks to probe() to avoid division by
zero in mwifiex_write_data_sync() in case a malicious device has broken
descriptors (or when doing descriptor fuzz testing).
Only add checks for the firmware-download boot stage, which require both
command endpoints, for now. The driver looks like it will handle a
missing endpoint during normal operation without oopsing, albeit not
very gracefully as it will try to submit URBs to the default pipe and
fail.
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4f ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: 4daffe3543 ("mwifiex: add support for Marvell USB8797 chipset")
Cc: stable@vger.kernel.org # 3.5
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027080819.6675-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b16bef60a9 upstream.
The driver and its bindings, before commit 04f9f068a6 ("regulator:
s5m8767: Modify parsing method of the voltage table of buck2/3/4") were
requiring to provide at least one safe/default voltage for DVS registers
if DVS GPIO is not being enabled.
IOW, if s5m8767,pmic-buck2-uses-gpio-dvs is missing, the
s5m8767,pmic-buck2-dvs-voltage should still be present and contain one
voltage.
This requirement was coming from driver behavior matching this condition
(none of DVS GPIO is enabled): it was always initializing the DVS
selector pins to 0 and keeping the DVS enable setting at reset value
(enabled). Therefore if none of DVS GPIO is enabled in devicetree,
driver was configuring the first DVS voltage for buck[234].
Mentioned commit 04f9f068a6 ("regulator: s5m8767: Modify parsing
method of the voltage table of buck2/3/4") broke it because DVS voltage
won't be parsed from devicetree if DVS GPIO is not enabled. After the
change, driver will configure bucks to use the register reset value as
voltage which might have unpleasant effects.
Fix this by relaxing the bindings constrain: if DVS GPIO is not enabled
in devicetree (therefore DVS voltage is also not parsed), explicitly
disable it.
Cc: <stable@vger.kernel.org>
Fixes: 04f9f068a6 ("regulator: s5m8767: Modify parsing method of the voltage table of buck2/3/4")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Rob Herring <robh@kernel.org>
Message-Id: <20211008113723.134648-2-krzysztof.kozlowski@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cbfcd13be5 upstream.
Current code contains a lot of racy patterns when converting an
ocontext's context structure to an SID. This is being done in a "lazy"
fashion, such that the SID is looked up in the SID table only when it's
first needed and then cached in the "sid" field of the ocontext
structure. However, this is done without any locking or memory barriers
and is thus unsafe.
Between commits 24ed7fdae6 ("selinux: use separate table for initial
SID lookup") and 66f8e2f03c ("selinux: sidtab reverse lookup hash
table"), this race condition lead to an actual observable bug, because a
pointer to the shared sid field was passed directly to
sidtab_context_to_sid(), which was using this location to also store an
intermediate value, which could have been read by other threads and
interpreted as an SID. In practice this caused e.g. new mounts to get a
wrong (seemingly random) filesystem context, leading to strange denials.
This bug has been spotted in the wild at least twice, see [1] and [2].
Fix the race condition by making all the racy functions use a common
helper that ensures the ocontext::sid accesses are made safely using the
appropriate SMP constructs.
Note that security_netif_sid() was populating the sid field of both
contexts stored in the ocontext, but only the first one was actually
used. The SELinux wiki's documentation on the "netifcon" policy
statement [3] suggests that using only the first context is intentional.
I kept only the handling of the first context here, as there is really
no point in doing the SID lookup for the unused one.
I wasn't able to reproduce the bug mentioned above on any kernel that
includes commit 66f8e2f03c, even though it has been reported that the
issue occurs with that commit, too, just less frequently. Thus, I wasn't
able to verify that this patch fixes the issue, but it makes sense to
avoid the race condition regardless.
[1] https://github.com/containers/container-selinux/issues/89
[2] https://lists.fedoraproject.org/archives/list/selinux@lists.fedoraproject.org/thread/6DMTAMHIOAOEMUAVTULJD45JZU7IBAFM/
[3] https://selinuxproject.org/page/NetworkStatements#netifcon
Cc: stable@vger.kernel.org
Cc: Xinjie Zheng <xinjie@google.com>
Reported-by: Sujithra Periasamy <sujithra@google.com>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c78a5e7aa upstream.
In open_ctree() in btrfs_check_rw_degradable() [1], we check each block
group individually if at least the minimum number of devices is available
for that profile. If all the devices are available, then we don't have to
check degradable.
[1]
open_ctree()
::
3559 if (!sb_rdonly(sb) && !btrfs_check_rw_degradable(fs_info, NULL)) {
Also before calling btrfs_check_rw_degradable() in open_ctee() at the
line number shown below [2] we call btrfs_read_chunk_tree() and down to
add_missing_dev() to record number of missing devices.
[2]
open_ctree()
::
3454 ret = btrfs_read_chunk_tree(fs_info);
btrfs_read_chunk_tree()
read_one_chunk() / read_one_dev()
add_missing_dev()
So, check if there is any missing device before btrfs_check_rw_degradable()
in open_ctree().
Also, with this the mount command could save ~16ms.[3] in the most
common case, that is no device is missing.
[3]
1) * 16934.96 us | btrfs_check_rw_degradable [btrfs]();
CC: stable@vger.kernel.org # 4.19+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10adb1152d upstream.
At replay_dir_deletes(), if find_dir_range() returns an error we break out
of the main while loop and then assign a value of 0 (success) to the 'ret'
variable, resulting in completely ignoring that an error happened. Fix
that by jumping to the 'out' label when find_dir_range() returns an error
(negative value).
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d03dbebba upstream.
Reported bug: https://github.com/kdave/btrfs-progs/issues/389
There's a problem with scrub reporting aborted status but returning
error code 0, on a filesystem with missing and readded device.
Roughly these steps:
- mkfs -d raid1 dev1 dev2
- fill with data
- unmount
- make dev1 disappear
- mount -o degraded
- copy more data
- make dev1 appear again
Running scrub afterwards reports that the command was aborted, but the
system log message says the exit code was 0.
It seems that the cause of the error is decrementing
fs_devices->missing_devices but not clearing device->dev_state. Every
time we umount filesystem, it would call close_ctree, And it would
eventually involve btrfs_close_one_device to close the device, but it
only decrements fs_devices->missing_devices but does not clear the
device BTRFS_DEV_STATE_MISSING bit. Worse, this bug will cause Integer
Overflow, because every time umount, fs_devices->missing_devices will
decrease. If fs_devices->missing_devices value hit 0, it would overflow.
With added debugging:
loop1: detected capacity change from 0 to 20971520
BTRFS: device fsid 56ad51f1-5523-463b-8547-c19486c51ebb devid 1 transid 21 /dev/loop1 scanned by systemd-udevd (2311)
loop2: detected capacity change from 0 to 20971520
BTRFS: device fsid 56ad51f1-5523-463b-8547-c19486c51ebb devid 2 transid 17 /dev/loop2 scanned by systemd-udevd (2313)
BTRFS info (device loop1): flagging fs with big metadata feature
BTRFS info (device loop1): allowing degraded mounts
BTRFS info (device loop1): using free space tree
BTRFS info (device loop1): has skinny extents
BTRFS info (device loop1): before clear_missing.00000000f706684d /dev/loop1 0
BTRFS warning (device loop1): devid 2 uuid 6635ac31-56dd-4852-873b-c60f5e2d53d2 is missing
BTRFS info (device loop1): before clear_missing.0000000000000000 /dev/loop2 1
BTRFS info (device loop1): flagging fs with big metadata feature
BTRFS info (device loop1): allowing degraded mounts
BTRFS info (device loop1): using free space tree
BTRFS info (device loop1): has skinny extents
BTRFS info (device loop1): before clear_missing.00000000f706684d /dev/loop1 0
BTRFS warning (device loop1): devid 2 uuid 6635ac31-56dd-4852-873b-c60f5e2d53d2 is missing
BTRFS info (device loop1): before clear_missing.0000000000000000 /dev/loop2 0
BTRFS info (device loop1): flagging fs with big metadata feature
BTRFS info (device loop1): allowing degraded mounts
BTRFS info (device loop1): using free space tree
BTRFS info (device loop1): has skinny extents
BTRFS info (device loop1): before clear_missing.00000000f706684d /dev/loop1 18446744073709551615
BTRFS warning (device loop1): devid 2 uuid 6635ac31-56dd-4852-873b-c60f5e2d53d2 is missing
BTRFS info (device loop1): before clear_missing.0000000000000000 /dev/loop2 18446744073709551615
If fs_devices->missing_devices is 0, next time it would be 18446744073709551615
After apply this patch, the fs_devices->missing_devices seems to be
right:
$ truncate -s 10g test1
$ truncate -s 10g test2
$ losetup /dev/loop1 test1
$ losetup /dev/loop2 test2
$ mkfs.btrfs -draid1 -mraid1 /dev/loop1 /dev/loop2 -f
$ losetup -d /dev/loop2
$ mount -o degraded /dev/loop1 /mnt/1
$ umount /mnt/1
$ mount -o degraded /dev/loop1 /mnt/1
$ umount /mnt/1
$ mount -o degraded /dev/loop1 /mnt/1
$ umount /mnt/1
$ dmesg
loop1: detected capacity change from 0 to 20971520
loop2: detected capacity change from 0 to 20971520
BTRFS: device fsid 15aa1203-98d3-4a66-bcae-ca82f629c2cd devid 1 transid 5 /dev/loop1 scanned by mkfs.btrfs (1863)
BTRFS: device fsid 15aa1203-98d3-4a66-bcae-ca82f629c2cd devid 2 transid 5 /dev/loop2 scanned by mkfs.btrfs (1863)
BTRFS info (device loop1): flagging fs with big metadata feature
BTRFS info (device loop1): allowing degraded mounts
BTRFS info (device loop1): disk space caching is enabled
BTRFS info (device loop1): has skinny extents
BTRFS info (device loop1): before clear_missing.00000000975bd577 /dev/loop1 0
BTRFS warning (device loop1): devid 2 uuid 8b333791-0b3f-4f57-b449-1c1ab6b51f38 is missing
BTRFS info (device loop1): before clear_missing.0000000000000000 /dev/loop2 1
BTRFS info (device loop1): checking UUID tree
BTRFS info (device loop1): flagging fs with big metadata feature
BTRFS info (device loop1): allowing degraded mounts
BTRFS info (device loop1): disk space caching is enabled
BTRFS info (device loop1): has skinny extents
BTRFS info (device loop1): before clear_missing.00000000975bd577 /dev/loop1 0
BTRFS warning (device loop1): devid 2 uuid 8b333791-0b3f-4f57-b449-1c1ab6b51f38 is missing
BTRFS info (device loop1): before clear_missing.0000000000000000 /dev/loop2 1
BTRFS info (device loop1): flagging fs with big metadata feature
BTRFS info (device loop1): allowing degraded mounts
BTRFS info (device loop1): disk space caching is enabled
BTRFS info (device loop1): has skinny extents
BTRFS info (device loop1): before clear_missing.00000000975bd577 /dev/loop1 0
BTRFS warning (device loop1): devid 2 uuid 8b333791-0b3f-4f57-b449-1c1ab6b51f38 is missing
BTRFS info (device loop1): before clear_missing.0000000000000000 /dev/loop2 1
CC: stable@vger.kernel.org # 4.19+
Signed-off-by: Li Zhang <zhanglikernel@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 42f2611cc1 ]
RDMA ULPs should only perform DMA through the ib_dma_* API instead of
using the hidden dma_device directly. In addition using the dma coherent
API family that dmapool is a part of can be very ineffcient on plaforms
that are not DMA coherent. Switch to use slab allocations and the
ib_dma_* APIs instead.
Link: https://lore.kernel.org/r/20201106181941.1878556-6-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4a146c7cf ]
The value of llc_testlink_time is set to the value stored in
net->ipv4.sysctl_tcp_keepalive_time when linkgroup init. The value of
sysctl_tcp_keepalive_time is already jiffies, so we don't need to
multiply by HZ, which would cause smc_link->llc_testlink_time overflow,
and test_link send flood.
Signed-off-by: Tony Lu <tonylu@linux.alibaba.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Reviewed-by: Wen Gu <guwen@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90a881fc35 ]
MTU change is refused whenever the value of new MTU is bigger than
the max packet bytes that fits in NFP Cluster Target Memory (CTM).
However, an eBPF program doesn't always need to access the whole
packet data.
The maximum direct packet access (DPA) offset has always been
caculated by verifier and stored in the max_pkt_offset field of prog
aux data.
Signed-off-by: Yu Xiao <yu.xiao@corigine.com>
Reviewed-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Reviewed-by: Niklas Soderlund <niklas.soderlund@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9159f10240 ]
The netif_device_detach() conditionally stops all tx queues if the queues
are running. There is no need to call netif_tx_stop_all_queues() again.
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86aeda32b8 ]
Pass the correct length to nvmet_tcp_verify_hdgst, which is the pdu
header length. This fixes a wrong behaviour where header digest
verification passes although the digest is wrong.
Signed-off-by: Amit Engel <amit.engel@dell.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9586e67b91 ]
When dispatching a zone append write request to a SCSI zoned block device,
if the target zone of the request is already locked, the device driver will
return BLK_STS_ZONE_RESOURCE and the request will be pushed back to the
hctx dipatch queue. The queue will be marked as RESTART in
dd_finish_request() and restarted in __blk_mq_free_request(). However, this
restart applies to the hctx of the completed request. If the requeued
request is on a different hctx, dispatch will no be retried until another
request is submitted or the next periodic queue run triggers, leading to up
to 30 seconds latency for the requeued request.
Fix this problem by scheduling a queue restart similarly to the
BLK_STS_RESOURCE case or when we cannot get the budget.
Also, consolidate the checks into the "need_resource" variable to simplify
the condition.
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Niklas Cassel <Niklas.Cassel@wdc.com>
Link: https://lore.kernel.org/r/20211026165127.4151055-1-naohiro.aota@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9122a70a63 ]
During a testing of an user-space application which transmits UDP
multicast datagrams and utilizes multicast routing to send the UDP
datagrams out of defined network interfaces, I've found a multicast
router does not fill-in UDP checksum into locally produced, looped-back
and forwarded UDP datagrams, if an original output NIC the datagrams
are sent to has UDP TX checksum offload enabled.
The datagrams are sent malformed out of the NIC the datagrams have been
forwarded to.
It is because:
1. If TX checksum offload is enabled on the output NIC, UDP checksum
is not calculated by kernel and is not filled into skb data.
2. dev_loopback_xmit(), which is called solely by
ip_mc_finish_output(), sets skb->ip_summed = CHECKSUM_UNNECESSARY
unconditionally.
3. Since 35fc92a9 ("[NET]: Allow forwarding of ip_summed except
CHECKSUM_COMPLETE"), the ip_summed value is preserved during
forwarding.
4. If ip_summed != CHECKSUM_PARTIAL, checksum is not calculated during
a packet egress.
The minimum fix in dev_loopback_xmit():
1. Preserves skb->ip_summed CHECKSUM_PARTIAL. This is the
case when the original output NIC has TX checksum offload enabled.
The effects are:
a) If the forwarding destination interface supports TX checksum
offloading, the NIC driver is responsible to fill-in the
checksum.
b) If the forwarding destination interface does NOT support TX
checksum offloading, checksums are filled-in by kernel before
skb is submitted to the NIC driver.
c) For local delivery, checksum validation is skipped as in the
case of CHECKSUM_UNNECESSARY, thanks to skb_csum_unnecessary().
2. Translates ip_summed CHECKSUM_NONE to CHECKSUM_UNNECESSARY. It
means, for CHECKSUM_NONE, the behavior is unmodified and is there
to skip a looped-back packet local delivery checksum validation.
Signed-off-by: Cyril Strejc <cyril.strejc@skoda.cz>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 926245c7d2 ]
page_frag_free() won't completely release the memory
allocated for the commands, the cache page must be explicitly
freed by calling __page_frag_cache_drain().
This bug can be easily reproduced by repeatedly
executing the following command on the initiator:
$echo 1 > /sys/devices/virtual/nvme-fabrics/ctl/nvme0/reset_controller
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: John Meneghini <jmeneghi@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 042b2046d0 ]
The tx queues are not stopped during the live migration. As a result, the
ndo_start_xmit() may access netfront_info->queues which is freed by
talk_to_netback()->xennet_destroy_queues().
This patch is to netif_device_detach() at the beginning of xen-netfront
resuming, and netif_device_attach() at the end of resuming.
CPU A CPU B
talk_to_netback()
-> if (info->queues)
xennet_destroy_queues(info);
to free netfront_info->queues
xennet_start_xmit()
to access netfront_info->queues
-> err = xennet_create_queues(info, &num_queues);
The idea is borrowed from virtio-net.
Cc: Joe Jin <joe.jin@oracle.com>
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 162079f2dc ]
The Winbond MMC driver fails to build on ARCH=m68k so prevent
that build config. Silences these build errors:
../drivers/mmc/host/wbsd.c: In function 'wbsd_request_end':
../drivers/mmc/host/wbsd.c:212:28: error: implicit declaration of function 'claim_dma_lock' [-Werror=implicit-function-declaration]
212 | dmaflags = claim_dma_lock();
../drivers/mmc/host/wbsd.c:215:17: error: implicit declaration of function 'release_dma_lock'; did you mean 'release_task'? [-Werror=implicit-function-declaration]
215 | release_dma_lock(dmaflags);
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211017175949.23838-1-rdunlap@infradead.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55dd7e0590 ]
Commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e rx/tx delay
config") sets the RX/TX delay according to the phy-mode property in the
device tree. For the A20-olinuxino-lime2 board this is "rgmii", which is the
wrong setting.
Following the example of a900cac375 ("ARM: dts: sun7i: a20: bananapro:
Fix ethernet phy-mode") the phy-mode is changed to "rgmii-id" which gets
the Ethernet working again on this board.
Signed-off-by: Bastien Roucariès <rouca@debian.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210916081721.237137-1-rouca@debian.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8017c99680 ]
On arm64 randconfig builds, hyperv sometimes fails with this
error:
In file included from drivers/hv/hv_trace.c:3:
In file included from drivers/hv/hyperv_vmbus.h:16:
In file included from arch/arm64/include/asm/sync_bitops.h:5:
arch/arm64/include/asm/bitops.h:11:2: error: only <linux/bitops.h> can be included directly
In file included from include/asm-generic/bitops/hweight.h:5:
include/asm-generic/bitops/arch_hweight.h:9:9: error: implicit declaration of function '__sw_hweight32' [-Werror,-Wimplicit-function-declaration]
include/asm-generic/bitops/atomic.h:17:7: error: implicit declaration of function 'BIT_WORD' [-Werror,-Wimplicit-function-declaration]
Include the correct header first.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211018131929.2260087-1-arnd@kernel.org
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf6abf345d ]
Use pci_info instead to avoid unnamed/uninitialized noise:
[197088.688729] sfc 0000:01:00.0: Solarflare NIC detected
[197088.690333] sfc 0000:01:00.0: Part Number : SFN5122F
[197088.729061] sfc 0000:01:00.0 (unnamed net_device) (uninitialized): no SR-IOV VFs probed
[197088.729071] sfc 0000:01:00.0 (unnamed net_device) (uninitialized): no PTP support
Inspired by fa44821a4d ("sfc: don't use netif_info et al before
net_device is registered") from Heiner Kallweit.
Signed-off-by: Erik Ekman <erik@kryo.se>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c62041c5ba ]
The 1/10GbaseT modes were set up for cards with SFP+ cages in
3497ed8c85 ("sfc: report supported link speeds on SFP connections").
10GbaseT was likely used since no 10G fibre mode existed.
The missing fibre modes for 1/10G were added to ethtool.h in 5711a98221
("net: ethtool: add support for 1000BaseX and missing 10G link modes")
shortly thereafter.
The user guide available at https://support-nic.xilinx.com/wp/drivers
lists support for the following cable and transceiver types in section 2.9:
- QSFP28 100G Direct Attach Cables
- QSFP28 100G SR Optical Transceivers (with SR4 modules listed)
- SFP28 25G Direct Attach Cables
- SFP28 25G SR Optical Transceivers
- QSFP+ 40G Direct Attach Cables
- QSFP+ 40G Active Optical Cables
- QSFP+ 40G SR4 Optical Transceivers
- QSFP+ to SFP+ Breakout Direct Attach Cables
- QSFP+ to SFP+ Breakout Active Optical Cables
- SFP+ 10G Direct Attach Cables
- SFP+ 10G SR Optical Transceivers
- SFP+ 10G LR Optical Transceivers
- SFP 1000BASE‐T Transceivers
- 1G Optical Transceivers
(From user guide issue 28. Issue 16 which also includes older cards like
SFN5xxx/SFN6xxx has matching lists for 1/10/40G transceiver types.)
Regarding SFP+ 10GBASE‐T transceivers the latest guide says:
"Solarflare adapters do not support 10GBASE‐T transceiver modules."
Tested using SFN5122F-R7 (with 2 SFP+ ports). Supported link modes do not change
depending on module used (tested with 1000BASE-T, 1000BASE-BX10, 10GBASE-LR).
Before:
$ ethtool ext
Settings for ext:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseT/Full
10000baseT/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Link partner advertised link modes: Not reported
Link partner advertised pause frame use: No
Link partner advertised auto-negotiation: No
Link partner advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Auto-negotiation: off
Port: FIBRE
PHYAD: 255
Transceiver: internal
Current message level: 0x000020f7 (8439)
drv probe link ifdown ifup rx_err tx_err hw
Link detected: yes
After:
$ ethtool ext
Settings for ext:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseT/Full
1000baseX/Full
10000baseCR/Full
10000baseSR/Full
10000baseLR/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Link partner advertised link modes: Not reported
Link partner advertised pause frame use: No
Link partner advertised auto-negotiation: No
Link partner advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Auto-negotiation: off
Port: FIBRE
PHYAD: 255
Transceiver: internal
Supports Wake-on: g
Wake-on: d
Current message level: 0x000020f7 (8439)
drv probe link ifdown ifup rx_err tx_err hw
Link detected: yes
Signed-off-by: Erik Ekman <erik@kryo.se>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c69b2f4687 ]
During the process of driver probing, the probe function should return < 0
for failure, otherwise, the kernel will treat value > 0 as success.
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e211210098 ]
During the process of driver probing, the probe function should return < 0
for failure, otherwise, the kernel will treat value > 0 as success.
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a8f71014b ]
The sgl is freed in the target stack in target_release_cmd_kref() before
calling qlt_free_cmd() but there is an unmap of sgl in qlt_free_cmd() that
causes a panic if sgl is not yet DMA unmapped:
NIP dma_direct_unmap_sg+0xdc/0x180
LR dma_direct_unmap_sg+0xc8/0x180
Call Trace:
ql_dbg_prefix+0x68/0xc0 [qla2xxx] (unreliable)
dma_unmap_sg_attrs+0x54/0xf0
qlt_unmap_sg.part.19+0x54/0x1c0 [qla2xxx]
qlt_free_cmd+0x124/0x1d0 [qla2xxx]
tcm_qla2xxx_release_cmd+0x4c/0xa0 [tcm_qla2xxx]
target_put_sess_cmd+0x198/0x370 [target_core_mod]
transport_generic_free_cmd+0x6c/0x1b0 [target_core_mod]
tcm_qla2xxx_complete_free+0x6c/0x90 [tcm_qla2xxx]
The sgl may be left unmapped in error cases of response sending. For
instance, qlt_rdy_to_xfer() maps sgl and exits when session is being
deleted keeping the sgl mapped.
This patch removes use-after-free of the sgl and ensures that the sgl is
unmapped for any command that was not sent to firmware.
Link: https://lore.kernel.org/r/20211018122650.11846-1-d.bogdanov@yadro.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Dmitry Bogdanov <d.bogdanov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2cddb44bd ]
During the process of driver probing, the probe function should return < 0
for failure, otherwise, the kernel will treat value > 0 as success.
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d94befbb5a ]
In laptop 'HP Spectre x360 Convertible 15-eb1xxx/8811' both front and
rear speakers are silent, this patch fixes that by overriding the pin
layout and by initializing the amplifier which needs a GPIO pin to be
set to 1 then 0, similar to the existing HP Spectre x360 14 model.
In order to have volume control, both front and rear speakers were
forced to use the DAC1.
This patch also correctly map the mute LED but since there is no
microphone on/off switch exposed by the alsa subsystem it never turns
on by itself.
There are still known audio issues in this laptop: headset microphone
doesn't work, the button to mute/unmute microphone is not yet mapped,
the LED of the mute/unmute speakers doesn't seems to be exposed via
GPIO and never turns on.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=213953
Signed-off-by: Davide Baldo <davide@baldo.me>
Link: https://lore.kernel.org/r/20211015072121.5287-1-davide@baldo.me
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c448b7aa3e ]
'component' is allocated in snd_soc_register_component(), but component->list
is not initalized, this may cause snd_soc_del_component_unlocked() deref null
ptr in the error handing case.
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
RIP: 0010:__list_del_entry_valid+0x81/0xf0
Call Trace:
snd_soc_del_component_unlocked+0x69/0x1b0 [snd_soc_core]
snd_soc_add_component.cold+0x54/0x6c [snd_soc_core]
snd_soc_register_component+0x70/0x90 [snd_soc_core]
devm_snd_soc_register_component+0x5e/0xd0 [snd_soc_core]
tas2552_probe+0x265/0x320 [snd_soc_tas2552]
? tas2552_component_probe+0x1e0/0x1e0 [snd_soc_tas2552]
i2c_device_probe+0xa31/0xbe0
Fix by adding INIT_LIST_HEAD() to snd_soc_component_initialize().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20211009065840.3196239-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6ff53f6a43 upstream.
Add a synchronize_rcu() after clearing the posted interrupt wakeup handler
to ensure all readers, i.e. in-flight IRQ handlers, see the new handler
before returning to the caller. If the caller is an exiting module and
is unregistering its handler, failure to wait could result in the IRQ
handler jumping into an unloaded module.
The registration path doesn't require synchronization, as it's the
caller's responsibility to not generate interrupts it cares about until
after its handler is registered.
Fixes: f6b3c72c23 ("x86/irq: Define a global vector for VT-d Posted-Interrupts")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211009001107.3936588-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 415de44076 upstream.
Currently, Linux probes for X86_BUG_NULL_SEL unconditionally which
makes it unsafe to migrate in a virtualised environment as the
properties across the migration pool might differ.
To be specific, the case which goes wrong is:
1. Zen1 (or earlier) and Zen2 (or later) in a migration pool
2. Linux boots on Zen2, probes and finds the absence of X86_BUG_NULL_SEL
3. Linux is then migrated to Zen1
Linux is now running on a X86_BUG_NULL_SEL-impacted CPU while believing
that the bug is fixed.
The only way to address the problem is to fully trust the "no longer
affected" CPUID bit when virtualised, because in the above case it would
be clear deliberately to indicate the fact "you might migrate to
somewhere which has this behaviour".
Zen3 adds the NullSelectorClearsBase CPUID bit to indicate that loading
a NULL segment selector zeroes the base and limit fields, as well as
just attributes. Zen2 also has this behaviour but doesn't have the NSCB
bit.
[ bp: Minor touchups. ]
Signed-off-by: Jane Malalane <jane.malalane@citrix.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
CC: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20211021104744.24126-1-jane.malalane@citrix.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7d445ab26 upstream.
When runtime support for converting between 4-level and 5-level pagetables
was added to the kernel, the SME code that built pagetables was updated
to use the pagetable functions, e.g. p4d_offset(), etc., in order to
simplify the code. However, the use of the pagetable functions in early
boot code requires the use of the USE_EARLY_PGTABLE_L5 #define in order to
ensure that the proper definition of pgtable_l5_enabled() is used.
Without the #define, pgtable_l5_enabled() is #defined as
cpu_feature_enabled(X86_FEATURE_LA57). In early boot, the CPU features
have not yet been discovered and populated, so pgtable_l5_enabled() will
return false even when 5-level paging is enabled. This causes the SME code
to always build 4-level pagetables to perform the in-place encryption.
If 5-level paging is enabled, switching to the SME pagetables results in
a page-fault that kills the boot.
Adding the #define results in pgtable_l5_enabled() using the
__pgtable_l5_enabled variable set in early boot and the SME code building
pagetables for the proper paging level.
Fixes: aad983913d ("x86/mm/encrypt: Simplify sme_populate_pgd() and sme_populate_pgd_large()")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: <stable@vger.kernel.org> # 4.18.x
Link: https://lkml.kernel.org/r/2cb8329655f5c753905812d951e212022a480475.1634318656.git.thomas.lendacky@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 712a951025 upstream.
It is possible to trigger a crash by splicing anon pipe bufs to the fuse
device.
The reason for this is that anon_pipe_buf_release() will reuse buf->page if
the refcount is 1, but that page might have already been stolen and its
flags modified (e.g. PG_lru added).
This happens in the unlikely case of fuse_dev_splice_write() getting around
to calling pipe_buf_release() after a page has been stolen, added to the
page cache and removed from the page cache.
Fix by calling pipe_buf_release() right after the page was inserted into
the page cache. In this case the page has an elevated refcount so any
release function will know that the page isn't reusable.
Reported-by: Frank Dinoff <fdinoff@google.com>
Link: https://lore.kernel.org/r/CAAmZXrsGg2xsP1CK+cbuEMumtrqdvD-NKnWzhNcvn71RV3c1yw@mail.gmail.com/
Fixes: dd3bb14f44 ("fuse: support splice() writing to fuse device")
Cc: <stable@vger.kernel.org> # v2.6.35
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1811bc401a upstream.
After we drop i_data sem, we need to reload the ext4_ext_path
structure since the extent tree can change once i_data_sem is
released.
This addresses the BUG:
[52117.465187] ------------[ cut here ]------------
[52117.465686] kernel BUG at fs/ext4/extents.c:1756!
...
[52117.478306] Call Trace:
[52117.478565] ext4_ext_shift_extents+0x3ee/0x710
[52117.479020] ext4_fallocate+0x139c/0x1b40
[52117.479405] ? __do_sys_newfstat+0x6b/0x80
[52117.479805] vfs_fallocate+0x151/0x4b0
[52117.480177] ksys_fallocate+0x4a/0xa0
[52117.480533] __x64_sys_fallocate+0x22/0x30
[52117.480930] do_syscall_64+0x35/0x80
[52117.481277] entry_SYSCALL_64_after_hwframe+0x44/0xae
[52117.481769] RIP: 0033:0x7fa062f855ca
Cc: stable@kernel.org
Link: https://lore.kernel.org/r/20210903062748.4118886-4-yangerkun@huawei.com
Signed-off-by: yangerkun <yangerkun@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39fec6889d upstream.
Ext4 file system has default lazy inode table initialization setup once
it is mounted. However, it has issue on computing the next schedule time
that makes the timeout same amount in jiffies but different real time in
secs if with various HZ values. Therefore, fix by measuring the current
time in a more granular unit nanoseconds and make the next schedule time
independent of the HZ value.
Fixes: bfff68738f ("ext4: add support for lazy inode table initialization")
Signed-off-by: Shaoying Xu <shaoyi@amazon.com>
Cc: stable@vger.kernel.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Link: https://lore.kernel.org/r/20210902164412.9994-2-shaoyi@amazon.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0317c0e87 upstream.
When the timer instance was add into ack_list but was not currently in
process, the user could stop it via snd_timer_stop1() without delete it
from the ack_list. Then the user could free the timer instance and when
it was actually processed UAF occurred.
This issue could be reproduced via testcase snd_timer01 in ltp - running
several instances of that testcase at the same time.
What I actually met was that the ack_list of the timer broken and the
kernel went into deadloop with irqoff. That could be detected by
hardlockup detector on board or when we run it on qemu, we could use gdb
to dump the ack_list when the console has no response.
To fix this issue, we delete the timer instance from ack_list and
active_list unconditionally in snd_timer_stop1().
Signed-off-by: Wang Wensheng <wangwensheng4@huawei.com>
Suggested-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211103033517.80531-1-wangwensheng4@huawei.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39173303c8 upstream.
The recent change in hda-intel driver to allow repeated probes
surfaced a problem that has been hidden until; the probe process in
the work calls azx_free() at the error path, and this skips the card
free process that eventually releases codec instances. As a result,
we get a kernel WARNING like:
snd_hda_intel 0000:00:1f.3: Cannot probe codecs, giving up
------------[ cut here ]------------
WARNING: CPU: 14 PID: 186 at sound/hda/hdac_bus.c:73
....
For fixing this, we need to call snd_card_free() instead of
azx_free(). Additionally, the device drvdata has to be cleared, as
the driver binding itself is still active. Then the PM and other
driver callbacks will ignore the procedure.
Fixes: c0f1886de7 ("ALSA: hda: intel: Allow repeatedly probing on codec configuration errors")
Reported-and-tested-by: Scott Branden <scott.branden@broadcom.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/063e2397-7edb-5f48-7b0d-618b938d9dd8@broadcom.com
Link: https://lore.kernel.org/r/20211110194633.19098-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f27b68906 upstream.
Adding the Line6 HX-Stomp XL USB_ID as it needs this fixed frequency
quirk as well.
The device is basically just the HX-Stomp with some more buttons on
the face. I've done some recording with it after adding it, and it
seems to function properly with this fix. The Midi features appear to
be working as well.
[ a coding style fix and patch reformat by tiwai ]
Signed-off-by: Jason Ormes <skryking@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211030200405.1358678-1-skryking@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 55f261b73a upstream.
Add the missing endpoint max-packet sanity check to probe() to avoid
division by zero in alloc_stream_buffers() in case a malicious device
has broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4f ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: 63978ab3e3 ("sound: add Edirol UA-101 support")
Cc: stable@vger.kernel.org # 2.6.34
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211026095401.26522-1-johan@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 861f92cb91 upstream.
Drivers that do not use the ctrl-framework use this function instead.
Fix the following issues:
- Do not check for multiple classes when getting the DEF_VAL.
- Return -EINVAL for request_api calls
- Default value cannot be changed, return EINVAL as soon as possible.
- Return the right error_idx
[If an error is found when validating the list of controls passed with
VIDIOC_G_EXT_CTRLS, then error_idx shall be set to ctrls->count to
indicate to userspace that no actual hardware was touched.
It would have been much nicer of course if error_idx could point to the
control index that failed the validation, but sadly that's not how the
API was designed.]
Fixes v4l2-compliance:
Control ioctls (Input 0):
warn: v4l2-test-controls.cpp(834): error_idx should be equal to count
warn: v4l2-test-controls.cpp(855): error_idx should be equal to count
fail: v4l2-test-controls.cpp(813): doioctl(node, VIDIOC_G_EXT_CTRLS, &ctrls)
test VIDIOC_G/S/TRY_EXT_CTRLS: FAIL
Buffer ioctls (Input 0):
fail: v4l2-test-buffers.cpp(1994): ret != EINVAL && ret != EBADR && ret != ENOTTY
test Requests: FAIL
Cc: stable@vger.kernel.org
Fixes: 6fa6f831f0 ("media: v4l2-ctrls: add core request support")
Suggested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0887e9e152 upstream.
The mem-to-mem stateless decoder API specifies support for dynamic
resolution changes. In particular, the decoder should accept format
changes on the OUTPUT queue even when buffers have been allocated,
as long as it is not streaming.
Relax restrictions for S_FMT as described in the previous paragraph,
and as long as the codec format remains the same. This aligns it with
the Hantro and Cedrus decoders. This change was mostly based on commit
ae02d49493 ("media: hantro: Fix s_fmt for dynamic resolution changes").
Since rkvdec_s_fmt() is now just a wrapper around the output/capture
variants without any additional shared functionality, drop the wrapper
and call the respective functions directly.
Fixes: cd33c83044 ("media: rkvdec: Add the rkvdec driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 298d8e8f7b upstream.
The rkvdec H.264 decoder currently overrides sizeimage for the output
format. This causes issues when userspace requires and requests a larger
buffer, but ends up with one of insufficient size.
Instead, only provide a default size if none was requested. This fixes
the video_decode_accelerator_tests from Chromium failing on the first
frame due to insufficient buffer space. It also aligns the behavior
of the rkvdec driver with the Hantro and Cedrus drivers.
Fixes: cd33c83044 ("media: rkvdec: Add the rkvdec driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2ac5fb35cd upstream.
sizeof when applied to a pointer typed expression gives the size of
the pointer.
./drivers/firmware/psci/psci_checker.c:158:41-47: ERROR application of sizeof to pointer
This issue was detected with the help of Coccinelle.
Fixes: 7401056de5 ("drivers/firmware: psci_checker: stash and use topology_core_cpumask for hotplug tests")
Cc: stable@vger.kernel.org
Reported-by: Zeal Robot <zealci@zte.com.cn>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: jing yangyang <jing.yangyang@zte.com.cn>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8779e05ba8 upstream.
The TIF_XXX flags are stored in the flags field in the thread_info
struct (TI_FLAGS), not in the flags field of the task_struct structure
(TASK_FLAGS).
It seems this bug didn't generate any important side-effects, otherwise it
wouldn't have went unnoticed for 12 years (since v2.6.32).
Signed-off-by: Helge Deller <deller@gmx.de>
Fixes: ecd3d4bc06 ("parisc: stop using task->ptrace for {single,block}step flags")
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e866a4628 upstream.
Fix a kernel crash which happens on PA1.x CPUs while initializing the
FTRACE/KPROBE breakpoints. The PTE table entries for the fixmap area
were not created correctly.
Signed-off-by: Helge Deller <deller@gmx.de>
Fixes: ccfbc68d41 ("parisc: add set_fixmap()/clear_fixmap()")
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c336d6e33 upstream.
When calculating i_blocks, there was a mistake that was masked with a
32-bit variable. So i_blocks for files larger than 4 GiB had incorrect
values. Mask with a 64-bit variable instead of 32-bit one.
Fixes: 5f2aa07507 ("exfat: add inode operations")
Cc: stable@vger.kernel.org # v5.7+
Reported-by: Ganapathi Kamath <hgkamath@hotmail.com>
Signed-off-by: Sungjong Seo <sj1557.seo@samsung.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 43592c8736 upstream.
Only wait for DRTO on reads, otherwise the driver hangs.
The driver prevents sending CMD12 on response errors like CRCs. According
to the comment this is because some cards have problems with this during
the UHS tuning sequence. Unfortunately this workaround currently also
applies for any command with data. On reads this will set the drto timer,
which then triggers after a while. On writes this will not set any timer
and the tasklet will not be scheduled again.
I cannot test for the UHS workarounds need, but even if so, it should at
most apply to reads. I have observed many hangs when CMD25 response
contained a CRC error. This patch fixes this without touching the actual
UHS tuning workaround.
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/af8f8b8674ba4fcc9a781019e4aeb72c@hyperstone.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 703535e6ae upstream.
No need to deduce command size in scsi_setup_scsi_cmnd() anymore as
appropriate checks have been added to scsi_fill_sghdr_rq() function and the
cmd_len should never be zero here. The code to do that wasn't correct
anyway, as it used uninitialized cmd->cmnd, which caused a null-ptr-deref
if the command size was zero as in the trace below. Fix this by removing
the unneeded code.
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
CPU: 0 PID: 1822 Comm: repro Not tainted 5.15.0 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-4.fc34 04/01/2014
Call Trace:
blk_mq_dispatch_rq_list+0x7c7/0x12d0
__blk_mq_sched_dispatch_requests+0x244/0x380
blk_mq_sched_dispatch_requests+0xf0/0x160
__blk_mq_run_hw_queue+0xe8/0x160
__blk_mq_delay_run_hw_queue+0x252/0x5d0
blk_mq_run_hw_queue+0x1dd/0x3b0
blk_mq_sched_insert_request+0x1ff/0x3e0
blk_execute_rq_nowait+0x173/0x1e0
blk_execute_rq+0x15c/0x540
sg_io+0x97c/0x1370
scsi_ioctl+0xe16/0x28e0
sd_ioctl+0x134/0x170
blkdev_ioctl+0x362/0x6e0
block_ioctl+0xb0/0xf0
vfs_ioctl+0xa7/0xf0
do_syscall_64+0x3d/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
---[ end trace 8b086e334adef6d2 ]---
Kernel panic - not syncing: Fatal exception
Link: https://lore.kernel.org/r/20211103170659.22151-2-tadeusz.struk@linaro.org
Fixes: 2ceda20f0a ("scsi: core: Move command size detection out of the fast path")
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: James E.J. Bottomley <jejb@linux.ibm.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: <linux-scsi@vger.kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Cc: <stable@vger.kernel.org> # 5.15, 5.14, 5.10
Reported-by: syzbot+5516b30f5401d4dcbcae@syzkaller.appspotmail.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tadeusz Struk <tadeusz.struk@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 839b63860e upstream.
Patch series "ocfs2: Truncate data corruption fix".
As further testing has shown, commit 5314454ea3 ("ocfs2: fix data
corruption after conversion from inline format") didn't fix all the data
corruption issues the customer started observing after 6dbf7bb555
("fs: Don't invalidate page buffers in block_write_full_page()") This
time I have tracked them down to two bugs in ocfs2 truncation code.
One bug (truncating page cache before clearing tail cluster and setting
i_size) could cause data corruption even before 6dbf7bb555, but before
that commit it needed a race with page fault, after 6dbf7bb555 it
started to be pretty deterministic.
Another bug (zeroing pages beyond old i_size) used to be harmless
inefficiency before commit 6dbf7bb555. But after commit 6dbf7bb555
in combination with the first bug it resulted in deterministic data
corruption.
Although fixing only the first problem is needed to stop data
corruption, I've fixed both issues to make the code more robust.
This patch (of 2):
ocfs2_truncate_file() did unmap invalidate page cache pages before
zeroing partial tail cluster and setting i_size. Thus some pages could
be left (and likely have left if the cluster zeroing happened) in the
page cache beyond i_size after truncate finished letting user possibly
see stale data once the file was extended again. Also the tail cluster
zeroing was not guaranteed to finish before truncate finished causing
possible stale data exposure. The problem started to be particularly
easy to hit after commit 6dbf7bb555 "fs: Don't invalidate page buffers
in block_write_full_page()" stopped invalidation of pages beyond i_size
from page writeback path.
Fix these problems by unmapping and invalidating pages in the page cache
after the i_size is reduced and tail cluster is zeroed out.
Link: https://lkml.kernel.org/r/20211025150008.29002-1-jack@suse.cz
Link: https://lkml.kernel.org/r/20211025151332.11301-1-jack@suse.cz
Fixes: ccd979bdbc ("[PATCH] OCFS2: The Second Oracle Cluster Filesystem")
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68dbbe7d5b upstream.
Some ATA drives are very slow to respond to READ_LOG_EXT and
READ_LOG_DMA_EXT commands issued from ata_dev_configure() when the
device is revalidated right after resuming a system or inserting the
ATA adapter driver (e.g. ahci). The default 5s timeout
(ATA_EH_CMD_DFL_TIMEOUT) used for these commands is too short, causing
errors during the device configuration. Ex:
...
ata9: SATA max UDMA/133 abar m524288@0x9d200000 port 0x9d200400 irq 209
ata9: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
ata9.00: ATA-9: XXX XXXXXXXXXXXXXXX, XXXXXXXX, max UDMA/133
ata9.00: qc timeout (cmd 0x2f)
ata9.00: Read log page 0x00 failed, Emask 0x4
ata9.00: Read log page 0x00 failed, Emask 0x40
ata9.00: NCQ Send/Recv Log not supported
ata9.00: Read log page 0x08 failed, Emask 0x40
ata9.00: 27344764928 sectors, multi 16: LBA48 NCQ (depth 32), AA
ata9.00: Read log page 0x00 failed, Emask 0x40
ata9.00: ATA Identify Device Log not supported
ata9.00: failed to set xfermode (err_mask=0x40)
ata9: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
ata9.00: configured for UDMA/133
...
The timeout error causes a soft reset of the drive link, followed in
most cases by a successful revalidation as that give enough time to the
drive to become fully ready to quickly process the read log commands.
However, in some cases, this also fails resulting in the device being
dropped.
Fix this by using adding the ata_eh_revalidate_timeouts entries for the
READ_LOG_EXT and READ_LOG_DMA_EXT commands. This defines a timeout
increased to 15s, retriable one time.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52f8869337 upstream.
Since binder was integrated with selinux, it has passed
'struct task_struct' associated with the binder_proc
to represent the source and target of transactions.
The conversion of task to SID was then done in the hook
implementations. It turns out that there are race conditions
which can result in an incorrect security context being used.
Fix by using the 'struct cred' saved during binder_open and pass
it to the selinux subsystem.
Cc: stable@vger.kernel.org # 5.14 (need backport for earlier stables)
Fixes: 79af73079d ("Add security hooks to binder and implement the hooks for SELinux.")
Suggested-by: Jann Horn <jannh@google.com>
Signed-off-by: Todd Kjos <tkjos@google.com>
Acked-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29bc22ac5e upstream.
Save the 'struct cred' associated with a binder process
at initial open to avoid potential race conditions
when converting to an euid.
Set a transaction's sender_euid from the 'struct cred'
saved at binder_open() instead of looking up the euid
from the binder proc's 'struct task'. This ensures
the euid is associated with the security context that
of the task that opened binder.
Cc: stable@vger.kernel.org # 4.4+
Fixes: 457b9a6f09 ("Staging: android: add binder driver")
Signed-off-by: Todd Kjos <tkjos@google.com>
Suggested-by: Stephen Smalley <stephen.smalley.work@gmail.com>
Suggested-by: Jann Horn <jannh@google.com>
Acked-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e1959faf08 upstream.
Some USB 3.1 enumeration issues were reported after the hub driver removed
the minimum 100ms limit for the power-on-good delay.
Since commit 90d28fb53d ("usb: core: reduce power-on-good delay time of
root hub") the hub driver sets the power-on-delay based on the
bPwrOn2PwrGood value in the hub descriptor.
xhci driver has a 20ms bPwrOn2PwrGood value for both roothubs based
on xhci spec section 5.4.8, but it's clearly not enough for the
USB 3.1 devices, causing enumeration issues.
Tests indicate full 100ms delay is needed.
Reported-by: Walt Jr. Brake <mr.yming81@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Fixes: 90d28fb53d ("usb: core: reduce power-on-good delay time of root hub")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211105160036.549516-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 063a326cba.
Reverting temporarily because not enabling the composite output has
been seen to break HDMI on older Pis.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
It referenced fragment@13 which used to be part of edt-ft5406.dtsi,
but has now been removed.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The code that set the scdc_enabled flag to ensure it was
disabled at boot time also ran on Pi0-3 where there is no
SCDC support. This lead to a warning in vc4_hdmi_encoder_post_crtc_disable
due to vc4_hdmi_disable_scrambling being called and trying to
read (and write) register HDMI_SCRAMBLER_CTL which doesn't
exist on those platforms.
Only set the flag should the interface be configured to support
more than HDMI 1.4.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add a check to vc4_hvs_gamma_check to ensure a new non-empty
gamma LUT is of the correct length before accepting it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
edt-ft5406.dtsi is included from vc4-kms-dsi-7inch which was
also setting i2c0mux and i2c0if status fields. This meant that
dtoverlay wouldn't apply the overlay due to multiple fragments
changing the same parameter.
Move the enable from edt-ft5406.dtsi to edt-ft5406-overlay.dts
for when it should be needed as an independent overlay.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Two calls were made to drm_crtc_enable_color_mgmt to add gamma
and CTM, however they were both set to add the gamma properties,
so they ended up added twice.
Fixes: 766cc6b1f7 "drm/vc4: Add CTM support"
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
With HVS5 the gamma block is now only reprogrammed with
a disable/enable. Loading the table from vc4_hvs_init_channel
(called from vc4_hvs_atomic_enable) appears to be at an
invalid point in time and so isn't applied.
Switch to enabling and disabling the gamma table instead. This
isn't safe if the pipeline is running, but it isn't now.
For HVS4 it is safe to enable and disable dynamically, so
adopt that approach there too.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The code falls through to "fail" under all conditions, so there is no
need for the drm_property_blob_put if the gamma lut hasn't been changed.
Fixes: 9cca26674a "drm: Check whether the gamma lut has changed before updating"
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
commit a44f9d6f9d upstream.
There is a wrong comparison of the total size of the loaded firmware
css->fw->size with the size of a pointer to struct imgu_fw_header.
Turn binary_header into a flexible-array member[1][2], use the
struct_size() helper and fix the wrong size comparison. Notice
that the loaded firmware needs to contain at least one 'struct
imgu_fw_info' item in the binary_header[] array.
It's also worth mentioning that
"css->fw->size < struct_size(css->fwp, binary_header, 1)"
with binary_header declared as a flexible-array member is equivalent
to
"css->fw->size < sizeof(struct imgu_fw_header)"
with binary_header declared as a one-element array (as in the original
code).
The replacement of the one-element array with a flexible-array member
also helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.10/process/deprecated.html#zero-length-and-one-element-arrays
Link: https://github.com/KSPP/linux/issues/79
Link: https://github.com/KSPP/linux/issues/109
Fixes: 09d290f0ba ("media: staging/intel-ipu3: css: Add support for firmware management")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a56d3e40bd upstream.
USB bulk and interrupt message timeouts are specified in milliseconds
and should specifically not vary with CONFIG_HZ.
Note that the bulk-out transfer timeout was set to the endpoint
bInterval value, which should be ignored for bulk endpoints and is
typically set to zero. This meant that a failing bulk-out transfer
would never time out.
Assume that the 10 second timeout used for all other transfers is more
than enough also for the bulk-out endpoint.
Fixes: 985cafccbf ("Staging: Comedi: vmk80xx: Add k8061 support")
Fixes: 951348b377 ("staging: comedi: vmk80xx: wait for URBs to complete")
Cc: stable@vger.kernel.org # 2.6.31
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20211025114532.4599-6-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a23461c474 upstream.
The driver uses endpoint-sized USB transfer buffers but up until
recently had no sanity checks on the sizes.
Commit e1f13c879a ("staging: comedi: check validity of wMaxPacketSize
of usb endpoints found") inadvertently fixed NULL-pointer dereferences
when accessing the transfer buffers in case a malicious device has a
zero wMaxPacketSize.
Make sure to allocate buffers large enough to handle also the other
accesses that are done without a size check (e.g. byte 18 in
vmk80xx_cnt_insn_read() for the VMK8061_MODEL) to avoid writing beyond
the buffers, for example, when doing descriptor fuzzing.
The original driver was for a low-speed device with 8-byte buffers.
Support was later added for a device that uses bulk transfers and is
presumably a full-speed device with a maximum 64-byte wMaxPacketSize.
Fixes: 985cafccbf ("Staging: Comedi: vmk80xx: Add k8061 support")
Cc: stable@vger.kernel.org # 2.6.31
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20211025114532.4599-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 536de747bc upstream.
USB transfer buffers are typically mapped for DMA and must not be
allocated on the stack or transfers will fail.
Allocate proper transfer buffers in the various command helpers and
return an error on short transfers instead of acting on random stack
data.
Note that this also fixes a stack info leak on systems where DMA is not
used as 32 bytes are always sent to the device regardless of how short
the command is.
Fixes: 63274cd7d3 ("Staging: comedi: add usb dt9812 driver")
Cc: stable@vger.kernel.org # 2.6.29
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211027093529.30896-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c052cc1a06 upstream.
Syzbot reported use-after-free in rtl8712_dl_fw(). The problem was in
race condition between r871xu_dev_remove() ->ndo_open() callback.
It's easy to see from crash log, that driver accesses released firmware
in ->ndo_open() callback. It may happen, since driver was releasing
firmware _before_ unregistering netdev. Fix it by moving
unregister_netdev() before cleaning up resources.
Call Trace:
...
rtl871x_open_fw drivers/staging/rtl8712/hal_init.c:83 [inline]
rtl8712_dl_fw+0xd95/0xe10 drivers/staging/rtl8712/hal_init.c:170
rtl8712_hal_init drivers/staging/rtl8712/hal_init.c:330 [inline]
rtl871x_hal_init+0xae/0x180 drivers/staging/rtl8712/hal_init.c:394
netdev_open+0xe6/0x6c0 drivers/staging/rtl8712/os_intfs.c:380
__dev_open+0x2bc/0x4d0 net/core/dev.c:1484
Freed by task 1306:
...
release_firmware+0x1b/0x30 drivers/base/firmware_loader/main.c:1053
r871xu_dev_remove+0xcc/0x2c0 drivers/staging/rtl8712/usb_intf.c:599
usb_unbind_interface+0x1d8/0x8d0 drivers/usb/core/driver.c:458
Fixes: 8c213fa591 ("staging: r8712u: Use asynchronous firmware loading")
Cc: stable <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+c55162be492189fb4f51@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/20211019211718.26354-1-paskripkin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3cffa06aee upstream.
The commit 48021f9813 ("printk: handle blank console arguments
passed in.") prevented crash caused by empty console= parameter value.
Unfortunately, this value is widely used on Chromebooks to disable
the console output. The above commit caused performance regression
because the messages were pushed on slow console even though nobody
was watching it.
Use ttynull driver explicitly for console="" and console=null
parameters. It has been created for exactly this purpose.
It causes that preferred_console is set. As a result, ttySX and ttyX
are not used as a fallback. And only ttynull console gets registered by
default.
It still allows to register other consoles either by additional console=
parameters or SPCR. It prevents regression because it worked this way even
before. Also it is a sane semantic. Preventing output on all consoles
should be done another way, for example, by introducing mute_console
parameter.
Link: https://lore.kernel.org/r/20201006025935.GA597@jagdpanzerIV.localdomain
Suggested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20201111135450.11214-3-pmladek@suse.com
Cc: Yi Fan <yfa@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32e9f56a96 upstream.
When freeing txn buffers, binder_transaction_buffer_release()
attempts to detect whether the current context is the target by
comparing current->group_leader to proc->tsk. This is an unreliable
test. Instead explicitly pass an 'is_failure' boolean.
Detecting the sender was being used as a way to tell if the
transaction failed to be sent. When cleaning up after
failing to send a transaction, there is no need to close
the fds associated with a BINDER_TYPE_FDA object. Now
'is_failure' can be used to accurately detect this case.
Fixes: 44d8047f1d ("binder: use standard functions to allocate fds")
Cc: stable <stable@vger.kernel.org>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Todd Kjos <tkjos@google.com>
Link: https://lore.kernel.org/r/20211015233811.3532235-1-tkjos@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 21b5fcdccb upstream.
musb_gadget_queue() adds the passed request to musb_ep::req_list. If the
endpoint is idle and it is the first request then it invokes
musb_queue_resume_work(). If the function returns an error then the
error is passed to the caller without any clean-up and the request
remains enqueued on the list. If the caller enqueues the request again
then the list corrupts.
Remove the request from the list on error.
Fixes: ea2f35c01d ("usb: musb: Fix sleeping function called from invalid context for hdrc glue")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Viraj Shah <viraj.shah@linutronix.de>
Link: https://lore.kernel.org/r/20211021093644.4734-1-viraj.shah@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a0548b2690 upstream.
On 64-bit:
drivers/usb/gadget/udc/fsl_qe_udc.c: In function ‘qe_ep0_rx’:
drivers/usb/gadget/udc/fsl_qe_udc.c:842:13: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
842 | vaddr = (u32)phys_to_virt(in_be32(&bd->buf));
| ^
In file included from drivers/usb/gadget/udc/fsl_qe_udc.c:41:
drivers/usb/gadget/udc/fsl_qe_udc.c:843:28: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
843 | frame_set_data(pframe, (u8 *)vaddr);
| ^
The driver assumes physical and virtual addresses are 32-bit, hence it
cannot work on 64-bit platforms.
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20211027080849.3276289-1-geert@linux-m68k.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d5e7a28b1 upstream.
This is a new warning in clang top-of-tree (will be clang 14):
In file included from arch/x86/kvm/mmu/mmu.c:27:
arch/x86/kvm/mmu/spte.h:318:9: error: use of bitwise '|' with boolean operands [-Werror,-Wbitwise-instead-of-logical]
return __is_bad_mt_xwr(rsvd_check, spte) |
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
||
arch/x86/kvm/mmu/spte.h:318:9: note: cast one or both operands to int to silence this warning
The code is fine, but change it anyway to shut up this clever clogs
of a compiler.
Reported-by: torvic9@mailbox.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[nathan: Backport to 5.10, which does not have 961f84457c]
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On a Pi 4, enabling composite video disables the HDMI output. As a
consequence, the composite output is disabled by default. Change the
vc4-kms-v3d overlay used on older Pis to also disable composite by
default, replacing the "nocomposite" parameter with a "composite"
parameter.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
commit df0380b953 upstream.
This is a fix equivalent with the upstream commit df0380b953 ("ALSA:
usb-audio: Add quirk for Audient iD14"), adapted to the earlier
kernels up to 5.14.y. It adds the quirk entry with the old
ignore_ctl_error flag to the usbmix_ctl_maps, instead.
The original commit description says:
Audient iD14 (2708:0002) may get a control message error that
interferes the operation e.g. with alsactl. Add the quirk to ignore
such errors like other devices.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22390ce786 upstream.
This is a fix equivalent with the upstream commit 22390ce786 ("ALSA:
usb-audio: add Schiit Hel device to quirk table"), adapted to the
earlier kernels up to 5.14.y. It adds the quirk entry with the old
ignore_ctl_error flag to the usbmix_ctl_maps, instead.
The original patch description says:
The Shciit Hel device responds to the ctl message for the mic capture
switch with a timeout of -EPIPE:
usb 7-2.2: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x1100, type = 1
usb 7-2.2: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x1100, type = 1
usb 7-2.2: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x1100, type = 1
usb 7-2.2: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x1100, type = 1
This seems safe to ignore as the device works properly with the control
message quirk, so add it to the quirk table so all is good.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eb4f756915 upstream.
After commit 77a7300aba ("of/irq: Get rid of NO_IRQ usage"),
no irq case has been removed, irq_of_parse_and_map() will return
0 in all cases when get error from parse and map an interrupt into
linux virq space.
amba_device_register() is only used on no-DT initialization, see
s3c64xx_pl080_init() arch/arm/mach-s3c/pl080.c
ep93xx_init_devices() arch/arm/mach-ep93xx/core.c
They won't set -1 to irq[0], so no need the warn.
This reverts commit 2eac58d502.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 35d2969ea3 upstream.
The bounds checking in avc_ca_pmt() is not strict enough. It should
be checking "read_pos + 4" because it's reading 5 bytes. If the
"es_info_length" is non-zero then it reads a 6th byte so there needs to
be an additional check for that.
I also added checks for the "write_pos". I don't think these are
required because "read_pos" and "write_pos" are tied together so
checking one ought to be enough. But they make the code easier to
understand for me. The check on write_pos is:
if (write_pos + 4 >= sizeof(c->operand) - 4) {
The first "+ 4" is because we're writing 5 bytes and the last " - 4"
is to leave space for the CRC.
The other problem is that "length" can be invalid. It comes from
"data_length" in fdtv_ca_pmt().
Cc: stable@vger.kernel.org
Reported-by: Luo Likang <luolikang@nsfocus.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e8684db191 upstream.
The driver allocates skb during ndo_open with GFP_ATOMIC which has high chance of failure when there are multiple instances.
GFP_KERNEL is enough while open and use GFP_ATOMIC only from interrupt context.
Fixes: 23f0703c12 ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 55161e67d4 upstream.
This reverts commit 09e856d54b.
When an interface is enslaved in a VRF, prerouting conntrack hook is
called twice: once in the context of the original input interface, and
once in the context of the VRF interface. If no special precausions are
taken, this leads to creation of two conntrack entries instead of one,
and breaks SNAT.
Commit above was intended to avoid creation of extra conntrack entries
when input interface is enslaved in a VRF. It did so by resetting
conntrack related data associated with the skb when it enters VRF context.
However it breaks netfilter operation. Imagine a use case when conntrack
zone must be assigned based on the original input interface, rather than
VRF interface (that would make original interfaces indistinguishable). One
could create netfilter rules similar to these:
chain rawprerouting {
type filter hook prerouting priority raw;
iif realiface1 ct zone set 1 return
iif realiface2 ct zone set 2 return
}
This works before the mentioned commit, but not after: zone assignment
is "forgotten", and any subsequent NAT or filtering that is dependent
on the conntrack zone does not work.
Here is a reproducer script that demonstrates the difference in behaviour.
==========
#!/bin/sh
# This script demonstrates unexpected change of nftables behaviour
# caused by commit 09e856d54b ""vrf: Reset skb conntrack
# connection on VRF rcv"
# https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=09e856d54bda5f288ef8437a90ab2b9b3eab83d1
#
# Before the commit, it was possible to assign conntrack zone to a
# packet (or mark it for `notracking`) in the prerouting chanin, raw
# priority, based on the `iif` (interface from which the packet
# arrived).
# After the change, # if the interface is enslaved in a VRF, such
# assignment is lost. Instead, assignment based on the `iif` matching
# the VRF master interface is honored. Thus it is impossible to
# distinguish packets based on the original interface.
#
# This script demonstrates this change of behaviour: conntrack zone 1
# or 2 is assigned depending on the match with the original interface
# or the vrf master interface. It can be observed that conntrack entry
# appears in different zone in the kernel versions before and after
# the commit.
IPIN=172.30.30.1
IPOUT=172.30.30.2
PFXL=30
ip li sh vein >/dev/null 2>&1 && ip li del vein
ip li sh tvrf >/dev/null 2>&1 && ip li del tvrf
nft list table testct >/dev/null 2>&1 && nft delete table testct
ip li add vein type veth peer veout
ip li add tvrf type vrf table 9876
ip li set veout master tvrf
ip li set vein up
ip li set veout up
ip li set tvrf up
/sbin/sysctl -w net.ipv4.conf.veout.accept_local=1
/sbin/sysctl -w net.ipv4.conf.veout.rp_filter=0
ip addr add $IPIN/$PFXL dev vein
ip addr add $IPOUT/$PFXL dev veout
nft -f - <<__END__
table testct {
chain rawpre {
type filter hook prerouting priority raw;
iif { veout, tvrf } meta nftrace set 1
iif veout ct zone set 1 return
iif tvrf ct zone set 2 return
notrack
}
chain rawout {
type filter hook output priority raw;
notrack
}
}
__END__
uname -rv
conntrack -F
ping -W 1 -c 1 -I vein $IPOUT
conntrack -L
Signed-off-by: Eugene Crosser <crosser@average.org>
Acked-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 041c614882 upstream.
Everything except the first 32 bits was lost when the pause flags were
added. This makes the 50000baseCR2 mode flag (bit 34) not appear.
I have tested this with a 10G card (SFN5122F-R7) by modifying it to
return a non-legacy link mode (10000baseCR).
Signed-off-by: Erik Ekman <erik@kryo.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We currently rely on two functions, vc4_hdmi_supports_scrambling() and
vc4_hdmi_mode_needs_scrambling() to determine if we should enable and
disable the scrambler for any given mode.
Since we might need to disable the controller at boot, we also always
run vc4_hdmi_disable_scrambling() and thus call those functions without
a mode yet, which in turns need to make some special casing in order for
it to work.
Instead of duplicating the check for whether or not we need to take care
of the scrambler in both vc4_hdmi_enable_scrambling() and
vc4_hdmi_disable_scrambling(), we can do that check only when we enable
it and store whether or not it's been enabled in our private structure.
We also need to initialize that flag at true to make sure we disable the
scrambler at boot since we can't really know its state yet.
This allows to simplify a bit that part of the driver, and removes one
user of our copy of the CRTC adjusted mode outside of KMS (since
vc4_hdmi_disable_scrambling() might be called from the hotplug interrupt
handler).
It also removes our last user of the legacy encoder->crtc pointer.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
We currently poke at encoder->crtc in the ALSA code path to determine
whether the HDMI output is enabled or not, and thus whether we should
allow the audio output.
However, that pointer is deprecated and shouldn't really be used by
atomic drivers anymore. Since we have the infrastructure in place now,
let's just create a flag that we toggle to report whether the controller
is currently enabled and use that instead of encoder->crtc in ALSA.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Even though we already check that the encoder->crtc pointer is there
during in startup(), which is part of the open() path in ASoC, nothing
guarantees that our encoder state won't change between the time when we
open the device and the time we prepare it.
Move the sanity checks we do in startup() to a helper and call it from
prepare().
Fixes: 91e99e1139 ("drm/vc4: hdmi: Register HDMI codec")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Accessing the crtc->state pointer from outside the modesetting context
is not allowed. We thus need to copy whatever we need from the KMS state
to our structure in order to access it.
However, in the vc4 HDMI driver we do use that pointer in the ALSA code
path, and potentially in the hotplug interrupt handler path.
These paths both need access to the CRTC adjusted mode in order for the
proper dividers to be set for ALSA, and the scrambler state to be
reinstated properly for hotplug.
Let's copy this mode into our private encoder structure and reference it
from there when needed. Since that part is shared between KMS and other
paths, we need to protect it using our mutex.
Link: https://lore.kernel.org/all/YWgteNaNeaS9uWDe@phenom.ffwll.local/
Fixes: bb7d785688 ("drm/vc4: Add HDMI audio support")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The vc4 HDMI controller registers into the KMS, CEC and ALSA
frameworks.
However, no particular care is done to prevent the concurrent execution
of different framework hooks from happening at the same time.
In order to protect against that scenario, let's introduce a mutex that
relevant ALSA and KMS hooks will need to take to prevent concurrent
execution.
CEC is left out at the moment though, since the .get_modes and .detect
KMS hooks, when running cec_s_phys_addr_from_edid, can end up calling
CEC's .adap_enable hook. This introduces some reentrancy that isn't easy
to deal with properly.
The CEC hooks also don't share much state with the rest of the driver:
the registers are entirely separate, we don't share any variable, the
only thing that can conflict is the CEC clock divider setup that can be
affected by a mode set.
However, after discussing it, it looks like CEC should be able to
recover from this if it was to happen.
Fixes: bb7d785688 ("drm/vc4: Add HDMI audio support")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The vc4 HDMI driver has multiple path shared between the CEC, ALSA and
KMS frameworks, plus two interrupt handlers (CEC and hotplug) that will
read and modify a number of registers.
Even though not bug has been reported so far, it's definitely unsafe, so
let's just add a spinlock to protect the register access of the HDMI
controller.
Fixes: c8b75bca92 ("drm/vc4: Add KMS support for Raspberry Pi.")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Accessing the crtc->state pointer from outside the modesetting context
is not allowed. We thus need to copy whatever we need from the KMS state
to our structure in order to access it.
In VC4, a number of users of that pointers have crept in over the years,
and the previous commits removed them all but the HVS channel a CRTC has
been assigned.
Let's move this channel in struct vc4_crtc at atomic_begin() time, drop
it from our private state structure, and remove our use of crtc->state
from our vblank handler entirely.
Link: https://lore.kernel.org/all/YWgteNaNeaS9uWDe@phenom.ffwll.local/
Fixes: 87ebcd42fb ("drm/vc4: crtc: Assign output to channel automatically")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
In some situation, we can end up being stuck on a non-blocking that went
through properly.
The situation that seems to trigger it reliably is to first start a
non-blocking commit, and then right after, and before we had any vblank
interrupt), start a blocking commit.
This will lead to the first commit workqueue to be scheduled, setup the
display, while the second commit is waiting for the first one to be
completed.
The vblank interrupt will then be raised, vc4_crtc_handle_vblank() will
run and will compare the active dlist in the HVS channel to the one
associated with the crtc->state.
However, at that point, the second commit is waiting using
drm_atomic_helper_wait_for_dependencies that occurs after
drm_atomic_helper_swap_state has been called, so crtc->state points to
the second commit state. vc4_crtc_handle_vblank() will compare the two
dlist addresses and since they don't match will ignore the interrupt.
The vblank event will never be reported, and the first and second commit
will wait for the first commit completion until they timeout.
The underlying reason is that it was never safe to do so. Indeed,
accessing the ->state pointer access synchronization is based on
ownership guarantees that can only occur within the functions and hooks
defined as part of the KMS framework, and obviously the irq handler
isn't one of them. The rework to move to generic helpers only uncovered
the underlying issue.
However, since the code path between
drm_atomic_helper_wait_for_dependencies() and
drm_atomic_helper_wait_for_vblanks() is serialised and we can't get two
commits in that path at the same time, we can work around this issue by
setting a variable associated to struct drm_crtc to the dlist we expect,
and then using it from the vc4_crtc_handle_vblank() function.
Since that state is shared with the modesetting path, we also need to
introduce a spinlock to protect the code shared between the interrupt
handler and the modesetting path, protecting only our new variable for
now.
Link: https://lore.kernel.org/all/YWgteNaNeaS9uWDe@phenom.ffwll.local/
Fixes: 56d1fe0979 ("drm/vc4: Make pageflip completion handling more robust.")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Accessing the crtc->state pointer from outside the modesetting context
is not allowed. We thus need to copy whatever we need from the KMS state
to our structure in order to access it.
In VC4, a number of users of that pointers have crept in over the years,
the first one being whether or not the downstream controller of the
pixelvalve is our writeback controller.
Fortunately for us, Since commit 39fcb28083 ("drm/vc4: txp: Turn the
TXP into a CRTC of its own") this is no longer something that can change
from one commit to the other and is hardcoded.
Let's set this flag in struct vc4_crtc if we happen to be the TXP, and
drop the flag from our private state structure.
Link: https://lore.kernel.org/all/YWgteNaNeaS9uWDe@phenom.ffwll.local/
Fixes: 008095e065 ("drm/vc4: Add support for the transposer block")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
It is important to reinitialise the firmware array pointers to protect
against the case that the brcmfmac driver is reprobed without first
being unloaded.
The potential hazard was noticed while investigating
https://github.com/raspberrypi/firmware/issues/1644 .
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
drm_crtc_legacy_gamma_set updates the gamma_lut blob unconditionally,
which leads to unnecessary reprogramming of hardware.
Check whether the blob contents has actually changed before
signalling that it has been updated.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
commit 29c77550ee upstream.
When perf.data is not written cleanly, we would like to process existing
data as much as possible (please see f_header.data.size == 0 condition
in perf_session__read_header). However, perf.data with partial data may
crash perf. Specifically, we see crash in 'perf script' for NULL
session->header.env.arch.
Fix this by checking session->header.env.arch before using it to determine
native_arch. Also split the if condition so it is easier to read.
Committer notes:
If it is a pipe, we already assume is a native arch, so no need to check
session->header.env.arch.
Signed-off-by: Song Liu <songliubraving@fb.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: kernel-team@fb.com
Cc: stable@vger.kernel.org
Link: http://lore.kernel.org/lkml/20211004053238.514936-1-songliubraving@fb.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54c5639d8f upstream.
Nathan reported that because KASAN_SHADOW_OFFSET was not defined in
Kconfig, it prevents asan-stack from getting disabled with clang even
when CONFIG_KASAN_STACK is disabled: fix this by defining the
corresponding config.
Reported-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Alexandre Ghiti <alexandre.ghiti@canonical.com>
Fixes: 8ad8b72721 ("riscv: Add KASAN support")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9b57e9d501 ]
The idea behind kicked mask is that we should not re-kick a vcpu that
is already in the "kick" process, i.e. that was kicked and is
is about to be dispatched if certain conditions are met.
The problem with the current implementation is, that it assumes the
kicked vcpu is going to enter SIE shortly. But under certain
circumstances, the vcpu we just kicked will be deemed non-runnable and
will remain in wait state. This can happen, if the interrupt(s) this
vcpu got kicked to deal with got already cleared (because the interrupts
got delivered to another vcpu). In this case kvm_arch_vcpu_runnable()
would return false, and the vcpu would remain in kvm_vcpu_block(),
but this time with its kicked_mask bit set. So next time around we
wouldn't kick the vcpu form __airqs_kick_single_vcpu(), but would assume
that we just kicked it.
Let us make sure the kicked_mask is cleared before we give up on
re-dispatching the vcpu.
Fixes: 9f30f62163 ("KVM: s390: add gib_alert_irq_handler()")
Reported-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Michael Mueller <mimu@linux.ibm.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Link: https://lore.kernel.org/r/20211019175401.3757927-2-pasic@linux.ibm.com
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 462512824f ]
TX/RX descriptor ring fields are always little-endian, but conversion
wasn't performed for big-endian CPUs, so the driver failed to work.
This patch makes the driver work on big-endian CPUs. It was tested and
confirmed to work on NXP P1010 processor (PowerPC).
Signed-off-by: Alexey Denisov <rtgbnm@gmail.com>
Link: https://lore.kernel.org/r/20210128044859.280219-1-rtgbnm@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d02831e51 ]
sctp_sf_ootb() is called when processing DATA chunk in closed state,
and many other places are also using it.
The vtag in the chunk's sctphdr should be verified, otherwise, as
later in chunk length check, it may send abort with the existent
asoc's vtag, which can be exploited by one to cook a malicious
chunk to terminate a SCTP asoc.
When fails to verify the vtag from the chunk, this patch sets asoc
to NULL, so that the abort will be made with the vtag from the
received chunk later.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef16b1734f ]
sctp_sf_do_8_5_1_E_sa() is called when processing SHUTDOWN_ACK chunk
in cookie_wait and cookie_echoed state.
The vtag in the chunk's sctphdr should be verified, otherwise, as
later in chunk length check, it may send abort with the existent
asoc's vtag, which can be exploited by one to cook a malicious
chunk to terminate a SCTP asoc.
Note that when fails to verify the vtag from SHUTDOWN-ACK chunk,
SHUTDOWN COMPLETE message will still be sent back to peer, but
with the vtag from SHUTDOWN-ACK chunk, as said in 5) of
rfc4960#section-8.4.
While at it, also remove the unnecessary chunk length check from
sctp_sf_shut_8_4_5(), as it's already done in both places where
it calls sctp_sf_shut_8_4_5().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa0f697e45 ]
sctp_sf_violation() is called when processing HEARTBEAT_ACK chunk
in cookie_wait state, and some other places are also using it.
The vtag in the chunk's sctphdr should be verified, otherwise, as
later in chunk length check, it may send abort with the existent
asoc's vtag, which can be exploited by one to cook a malicious
chunk to terminate a SCTP asoc.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a64b341b86 ]
1. In closed state: in sctp_sf_do_5_1D_ce():
When asoc is NULL, making packet for abort will use chunk's vtag
in sctp_ootb_pkt_new(). But when asoc exists, vtag from the chunk
should be verified before using peer.i.init_tag to make packet
for abort in sctp_ootb_pkt_new(), and just discard it if vtag is
not correct.
2. In the other states: in sctp_sf_do_5_2_4_dupcook():
asoc always exists, but duplicate cookie_echo's vtag will be
handled by sctp_tietags_compare() and then take actions, so before
that we only verify the vtag for the abort sent for invalid chunk
length.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 438b95a7c9 ]
Currently INIT_ACK chunk in non-cookie_echoed state is processed in
sctp_sf_discard_chunk() to send an abort with the existent asoc's
vtag if the chunk length is not valid. But the vtag in the chunk's
sctphdr is not verified, which may be exploited by one to cook a
malicious chunk to terminal a SCTP asoc.
sctp_sf_discard_chunk() also is called in many other places to send
an abort, and most of those have this problem. This patch is to fix
it by sending abort with the existent asoc's vtag only if the vtag
from the chunk's sctphdr is verified in sctp_sf_discard_chunk().
Note on sctp_sf_do_9_1_abort() and sctp_sf_shutdown_pending_abort(),
the chunk length has been verified before sctp_sf_discard_chunk(),
so replace it with sctp_sf_discard(). On sctp_sf_do_asconf_ack() and
sctp_sf_do_asconf(), move the sctp_chunk_length_valid check ahead of
sctp_sf_discard_chunk(), then replace it with sctp_sf_discard().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f7019c7eb ]
Currently Linux SCTP uses the verification tag of the existing SCTP
asoc when failing to process and sending the packet with the ABORT
chunk. This will result in the peer accepting the ABORT chunk and
removing the SCTP asoc. One could exploit this to terminate a SCTP
asoc.
This patch is to fix it by always using the initiate tag of the
received INIT chunk for the ABORT chunk to be sent.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit af1a02aa23 upstream.
There is a race condition where the PHY state machine can change
members of the phydev structure at the same time userspace requests a
change via ethtool. To prevent this, have phy_ethtool_ksettings_set
take the PHY lock.
Fixes: 2d55173e71 ("phy: add generic function to support ksetting support")
Reported-by: Walter Stoll <Walter.Stoll@duagon.com>
Suggested-by: Walter Stoll <Walter.Stoll@duagon.com>
Tested-by: Walter Stoll <Walter.Stoll@duagon.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 707293a56f upstream.
Split phy_start_aneg into a wrapper which takes the PHY lock, and a
helper doing the real work. This will be needed when
phy_ethtook_ksettings_set takes the lock.
Fixes: 2d55173e71 ("phy: add generic function to support ksetting support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 64cd92d5e8 upstream.
This allows it to make use of a helper which assume the PHY is already
locked.
Fixes: 2d55173e71 ("phy: add generic function to support ksetting support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c10a485c3d upstream.
The PHY structure should be locked while copying information out if
it, otherwise there is no guarantee of self consistency. Without the
lock the PHY state machine could be updating the structure.
Fixes: 2d55173e71 ("phy: add generic function to support ksetting support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d9d6fd21a upstream.
sk->sk_err contains a positive number, yet async_wait.err wants the
opposite. Fix the missed sign flip, which Jakub caught by inspection.
Fixes: a42055e8d2 ("net/tls: Add support for async encryption of records for performance")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Daniel Jordan <daniel.m.jordan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ace19b9924 upstream.
A hard hang is observed whenever the ethernet interface is brought
down. If the PHY is stopped before the LPC core block is reset,
the SoC will hang. Comparing lpc_eth_close() and lpc_eth_open() I
re-arranged the ordering of the functions calls in lpc_eth_close() to
reset the hardware before stopping the PHY.
Fixes: b7370112f5 ("lpc32xx: Added ethernet driver")
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 759635760a upstream.
When the driver fails to allocate a new Rx buffer, it passes an empty Rx
descriptor (contains zero address and size) to the device and marks it
as invalid by setting the skb pointer in the descriptor's metadata to
NULL.
After processing enough Rx descriptors, the driver will try to process
the invalid descriptor, but will return immediately seeing that the skb
pointer is NULL. Since the driver no longer passes new Rx descriptors to
the device, the Rx queue will eventually become full and the device will
start to drop packets.
Fix this by recycling the received packet if allocation of the new
packet failed. This means that allocation is no longer performed at the
end of the Rx routine, but at the start, before tearing down the DMA
mapping of the received packet.
Remove the comment about the descriptor being zeroed as it is no longer
correct. This is OK because we either use the descriptor as-is (when
recycling) or overwrite its address and size fields with that of the
newly allocated Rx buffer.
The issue was discovered when a process ("perf") consumed too much
memory and put the system under memory pressure. It can be reproduced by
injecting slab allocation failures [1]. After the fix, the Rx queue no
longer comes to a halt.
[1]
# echo 10 > /sys/kernel/debug/failslab/times
# echo 1000 > /sys/kernel/debug/failslab/interval
# echo 100 > /sys/kernel/debug/failslab/probability
FAULT_INJECTION: forcing a failure.
name failslab, interval 1000, probability 100, space 0, times 8
[...]
Call Trace:
<IRQ>
dump_stack_lvl+0x34/0x44
should_fail.cold+0x32/0x37
should_failslab+0x5/0x10
kmem_cache_alloc_node+0x23/0x190
__alloc_skb+0x1f9/0x280
__netdev_alloc_skb+0x3a/0x150
mlxsw_pci_rdq_skb_alloc+0x24/0x90
mlxsw_pci_cq_tasklet+0x3dc/0x1200
tasklet_action_common.constprop.0+0x9f/0x100
__do_softirq+0xb5/0x252
irq_exit_rcu+0x7a/0xa0
common_interrupt+0x83/0xa0
</IRQ>
asm_common_interrupt+0x1e/0x40
RIP: 0010:cpuidle_enter_state+0xc8/0x340
[...]
mlxsw_spectrum2 0000:06:00.0: Failed to alloc skb for RDQ
Fixes: eda6500a98 ("mlxsw: Add PCI bus implementation")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/20211024064014.1060919-1-idosch@idosch.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a089e95b4 upstream.
nios2:allmodconfig builds fail with
make[1]: *** No rule to make target 'arch/nios2/boot/dts/""',
needed by 'arch/nios2/boot/dts/built-in.a'. Stop.
make: [Makefile:1868: arch/nios2/boot/dts] Error 2 (ignored)
This is seen with compile tests since those enable NIOS2_DTB_SOURCE_BOOL,
which in turn enables NIOS2_DTB_SOURCE. This causes the build error
because the default value for NIOS2_DTB_SOURCE is an empty string.
Disable NIOS2_DTB_SOURCE_BOOL for compile tests to avoid the error.
Fixes: 2fc8483fdc ("nios2: Build infrastructure")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c57eeecc5 upstream.
Drivers call netdev_set_num_tc() and then netdev_set_tc_queue()
to set the queue count and offset for each TC. So the queue count
and offset for the TCs may be zero for a short period after dev->num_tc
has been set. If a TX packet is being transmitted at this time in the
code path netdev_pick_tx() -> skb_tx_hash(), skb_tx_hash() may see
nonzero dev->num_tc but zero qcount for the TC. The while loop that
keeps looping while hash >= qcount will not end.
Fix it by checking the TC's qcount to be nonzero before using it.
Fixes: eadec877ce ("net: Add support for subordinate traffic classes to netdev_pick_tx")
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7a1e76d0f upstream.
Currently in net_ns_get_ownership() it may not be able to set uid or gid
if make_kuid or make_kgid returns an invalid value, and an uninit-value
issue can be triggered by this.
This patch is to fix it by initializing the uid and gid before calling
net_ns_get_ownership(), as it does in kobject_get_ownership()
Fixes: e6dee9f389 ("net-sysfs: add netdev_change_owner()")
Reported-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f68cd6348 upstream.
Syzbot reported ODEBUG warning in batadv_nc_mesh_free(). The problem was
in wrong error handling in batadv_mesh_init().
Before this patch batadv_mesh_init() was calling batadv_mesh_free() in case
of any batadv_*_init() calls failure. This approach may work well, when
there is some kind of indicator, which can tell which parts of batadv are
initialized; but there isn't any.
All written above lead to cleaning up uninitialized fields. Even if we hide
ODEBUG warning by initializing bat_priv->nc.work, syzbot was able to hit
GPF in batadv_nc_purge_paths(), because hash pointer in still NULL. [1]
To fix these bugs we can unwind batadv_*_init() calls one by one.
It is good approach for 2 reasons: 1) It fixes bugs on error handling
path 2) It improves the performance, since we won't call unneeded
batadv_*_free() functions.
So, this patch makes all batadv_*_init() clean up all allocated memory
before returning with an error to no call correspoing batadv_*_free()
and open-codes batadv_mesh_free() with proper order to avoid touching
uninitialized fields.
Link: https://lore.kernel.org/netdev/000000000000c87fbd05cef6bcb0@google.com/ [1]
Reported-and-tested-by: syzbot+28b0702ada0bf7381f58@syzkaller.appspotmail.com
Fixes: c6c8fea297 ("net: Add batman-adv meshing protocol")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Acked-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 55e6d80378 upstream.
In regcache_rbtree_insert_to_block(), when 'present' realloc failed,
the 'blk' which is supposed to assign to 'rbnode->block' will be freed,
so 'rbnode->block' points a freed memory, in the error handling path of
regcache_rbtree_init(), 'rbnode->block' will be freed again in
regcache_rbtree_exit(), KASAN will report double-free as follows:
BUG: KASAN: double-free or invalid-free in kfree+0xce/0x390
Call Trace:
slab_free_freelist_hook+0x10d/0x240
kfree+0xce/0x390
regcache_rbtree_exit+0x15d/0x1a0
regcache_rbtree_init+0x224/0x2c0
regcache_init+0x88d/0x1310
__regmap_init+0x3151/0x4a80
__devm_regmap_init+0x7d/0x100
madera_spi_probe+0x10f/0x333 [madera_spi]
spi_probe+0x183/0x210
really_probe+0x285/0xc30
To fix this, moving up the assignment of rbnode->block to immediately after
the reallocation has succeeded so that the data structure stays valid even
if the second reallocation fails.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 3f4ff561bc ("regmap: rbtree: Make cache_present bitmap per node")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20211012023735.1632786-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e77bcdd1f6 upstream.
Currently, we are using a fixed buffer size of length 2048 to display
rsrc_alloc output. As a result a maximum of 2048 characters of
rsrc_alloc output is displayed, which may lead sometimes to display only
partial output. This patch fixes this dependency on max limit of buffer
size and displays all PF VF entries.
Each column of the debugfs entry "rsrc_alloc" uses a fixed width of 12
characters to print the list of LFs of each block for a PF/VF. If the
length of list of LFs of a block exceeds this fixed width then the list
gets truncated and displays only a part of the list. This patch fixes
this by using the maximum possible length of list of LFs among all
blocks of all PFs and VFs entries as the width size.
Fixes: f788409714 ("octeontx2-af: Formatting debugfs entry rsrc_alloc.")
Fixes: 23205e6d06 ("octeontx2-af: Dump current resource provisioning status")
Signed-off-by: Rakesh Babu <rsaladi2@marvell.com>
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <Sunil.Goutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce7723e9cd upstream.
With commit db5ad6b7f8 ("nvme-tcp: try to send request in queue_rq
context") r2t and response PDU can get processed while send function
is executing.
Current data digest send code uses req->offset after kernel_sendmsg(),
this creates a race condition where req->offset gets reset before it
is used in send function.
This can happen in two cases -
1. Target sends r2t PDU which resets req->offset.
2. Target send response PDU which completes the req and then req is
used for a new command, nvme_tcp_setup_cmd_pdu() resets req->offset.
Fix this by storing req->offset in a local variable and using
this local variable after kernel_sendmsg().
Fixes: db5ad6b7f8 ("nvme-tcp: try to send request in queue_rq context")
Signed-off-by: Varun Prakash <varun@chelsio.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54713c85f5 upstream.
Lorenzo noticed that the code testing for program type compatibility of
tail call maps is potentially racy in that two threads could encounter a
map with an unset type simultaneously and both return true even though they
are inserting incompatible programs.
The race window is quite small, but artificially enlarging it by adding a
usleep_range() inside the check in bpf_prog_array_compatible() makes it
trivial to trigger from userspace with a program that does, essentially:
map_fd = bpf_create_map(BPF_MAP_TYPE_PROG_ARRAY, 4, 4, 2, 0);
pid = fork();
if (pid) {
key = 0;
value = xdp_fd;
} else {
key = 1;
value = tc_fd;
}
err = bpf_map_update_elem(map_fd, &key, &value, 0);
While the race window is small, it has potentially serious ramifications in
that triggering it would allow a BPF program to tail call to a program of a
different type. So let's get rid of it by protecting the update with a
spinlock. The commit in the Fixes tag is the last commit that touches the
code in question.
v2:
- Use a spinlock instead of an atomic variable and cmpxchg() (Alexei)
v3:
- Put lock and the members it protects into an embedded 'owner' struct (Daniel)
Fixes: 3324b584b6 ("ebpf: misc core cleanup")
Reported-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20211026110019.363464-1-toke@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd9733f5d7 upstream.
With two Msgs, msgA and msgB and a user doing nonblocking sendmsg calls (or
multiple cores) on a single socket 'sk' we could get the following flow.
msgA, sk msgB, sk
----------- ---------------
tcp_bpf_sendmsg()
lock(sk)
psock = sk->psock
tcp_bpf_sendmsg()
lock(sk) ... blocking
tcp_bpf_send_verdict
if (psock->eval == NONE)
psock->eval = sk_psock_msg_verdict
..
< handle SK_REDIRECT case >
release_sock(sk) < lock dropped so grab here >
ret = tcp_bpf_sendmsg_redir
psock = sk->psock
tcp_bpf_send_verdict
lock_sock(sk) ... blocking on B
if (psock->eval == NONE) <- boom.
psock->eval will have msgA state
The problem here is we dropped the lock on msgA and grabbed it with msgB.
Now we have old state in psock and importantly psock->eval has not been
cleared. So msgB will run whatever action was done on A and the verdict
program may never see it.
Fixes: 604326b41a ("bpf, sockmap: convert to generic sk_msg interface")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20211012052019.184398-1-liujian56@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04f8ef5643 upstream.
When enabling CONFIG_CGROUP_BPF, kmemleak can be observed by running
the command as below:
$mount -t cgroup -o none,name=foo cgroup cgroup/
$umount cgroup/
unreferenced object 0xc3585c40 (size 64):
comm "mount", pid 425, jiffies 4294959825 (age 31.990s)
hex dump (first 32 bytes):
01 00 00 80 84 8c 28 c0 00 00 00 00 00 00 00 00 ......(.........
00 00 00 00 00 00 00 00 6c 43 a0 c3 00 00 00 00 ........lC......
backtrace:
[<e95a2f9e>] cgroup_bpf_inherit+0x44/0x24c
[<1f03679c>] cgroup_setup_root+0x174/0x37c
[<ed4b0ac5>] cgroup1_get_tree+0x2c0/0x4a0
[<f85b12fd>] vfs_get_tree+0x24/0x108
[<f55aec5c>] path_mount+0x384/0x988
[<e2d5e9cd>] do_mount+0x64/0x9c
[<208c9cfe>] sys_mount+0xfc/0x1f4
[<06dd06e0>] ret_fast_syscall+0x0/0x48
[<a8308cb3>] 0xbeb4daa8
This is because that since the commit 2b0d3d3e4f ("percpu_ref: reduce
memory footprint of percpu_ref in fast path") root_cgrp->bpf.refcnt.data
is allocated by the function percpu_ref_init in cgroup_bpf_inherit which
is called by cgroup_setup_root when mounting, but not freed along with
root_cgrp when umounting. Adding cgroup_bpf_offline which calls
percpu_ref_kill to cgroup_kill_sb can free root_cgrp->bpf.refcnt.data in
umount path.
This patch also fixes the commit 4bfc0bb2c6 ("bpf: decouple the lifetime
of cgroup_bpf from cgroup itself"). A cgroup_bpf_offline is needed to do a
cleanup that frees the resources which are allocated by cgroup_bpf_inherit
in cgroup_setup_root.
And inside cgroup_bpf_offline, cgroup_get() is at the beginning and
cgroup_put is at the end of cgroup_bpf_release which is called by
cgroup_bpf_offline. So cgroup_bpf_offline can keep the balance of
cgroup's refcount.
Fixes: 2b0d3d3e4f ("percpu_ref: reduce memory footprint of percpu_ref in fast path")
Fixes: 4bfc0bb2c6 ("bpf: decouple the lifetime of cgroup_bpf from cgroup itself")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Roman Gushchin <guro@fb.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20211018075623.26884-1-quanyang.wang@windriver.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db6c3c064f upstream.
Add the missing endpoint max-packet sanity check to probe() to avoid
division by zero in lan78xx_tx_bh() in case a malicious device has
broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4f ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Cc: stable@vger.kernel.org # 4.3
Cc: Woojung.Huh@microchip.com <Woojung.Huh@microchip.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09b1d5dc6c upstream.
The management registrations locking was broken, the list was
locked for each wdev, but cfg80211_mgmt_registrations_update()
iterated it without holding all the correct spinlocks, causing
list corruption.
Rather than trying to fix it with fine-grained locking, just
move the lock to the wiphy/rdev (still need the list on each
wdev), we already need to hold the wdev lock to change it, so
there's no contention on the lock in any case. This trivially
fixes the bug since we hold one wdev's lock already, and now
will hold the lock that protects all lists.
Cc: stable@vger.kernel.org
Reported-by: Jouni Malinen <j@w1.fi>
Fixes: 6cd536fe62 ("cfg80211: change internal management frame registration API")
Link: https://lore.kernel.org/r/20211025133111.5cf733eab0f4.I7b0abb0494ab712f74e2efcd24bb31ac33f7eee9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 25e1f67eda upstream.
We should not access request members after the last send, even to
determine if indeed it was the last data payload send. The reason is
that a completion could have arrived and trigger a new execution of the
request which overridden these members. This was fixed by commit
825619b09a ("nvme-tcp: fix possible use-after-completion").
Commit e371af033c broke that assumption again to address cases where
multiple r2t pdus are sent per request. To fix it, we need to record the
request data_sent and data_len and after the payload network send we
reference these counters to determine weather we should advance the
request iterator.
Fixes: e371af033c ("nvme-tcp: fix incorrect h2cdata pdu offset accounting")
Reported-by: Keith Busch <kbusch@kernel.org>
Cc: stable@vger.kernel.org # 5.10+
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f1b228529 upstream.
Encountered a race between ocfs2_test_bg_bit_allocatable() and
jbd2_journal_put_journal_head() resulting in the below vmcore.
PID: 106879 TASK: ffff880244ba9c00 CPU: 2 COMMAND: "loop3"
Call trace:
panic
oops_end
no_context
__bad_area_nosemaphore
bad_area_nosemaphore
__do_page_fault
do_page_fault
page_fault
[exception RIP: ocfs2_block_group_find_clear_bits+316]
ocfs2_block_group_find_clear_bits [ocfs2]
ocfs2_cluster_group_search [ocfs2]
ocfs2_search_chain [ocfs2]
ocfs2_claim_suballoc_bits [ocfs2]
__ocfs2_claim_clusters [ocfs2]
ocfs2_claim_clusters [ocfs2]
ocfs2_local_alloc_slide_window [ocfs2]
ocfs2_reserve_local_alloc_bits [ocfs2]
ocfs2_reserve_clusters_with_limit [ocfs2]
ocfs2_reserve_clusters [ocfs2]
ocfs2_lock_refcount_allocators [ocfs2]
ocfs2_make_clusters_writable [ocfs2]
ocfs2_replace_cow [ocfs2]
ocfs2_refcount_cow [ocfs2]
ocfs2_file_write_iter [ocfs2]
lo_rw_aio
loop_queue_work
kthread_worker_fn
kthread
ret_from_fork
When ocfs2_test_bg_bit_allocatable() called bh2jh(bg_bh), the
bg_bh->b_private NULL as jbd2_journal_put_journal_head() raced and
released the jounal head from the buffer head. Needed to take bit lock
for the bit 'BH_JournalHead' to fix this race.
Link: https://lkml.kernel.org/r/1634820718-6043-1-git-send-email-gautham.ananthakrishna@oracle.com
Signed-off-by: Gautham Ananthakrishna <gautham.ananthakrishna@oracle.com>
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: <rajesh.sivaramasubramaniom@oracle.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9af372dc70 upstream.
To reset standard tuning circuit completely, after clear ESDHC_MIX_CTRL_EXE_TUNE,
also need to clear bit buffer_read_ready, this operation will finally clear the
USDHC IP internal logic flag execute_tuning_with_clr_buf, make sure the following
normal data transfer will not be impacted by standard tuning logic used before.
Find this issue when do quick SD card insert/remove stress test. During standard
tuning prodedure, if remove SD card, USDHC standard tuning logic can't clear the
internal flag execute_tuning_with_clr_buf. Next time when insert SD card, all
data related commands can't get any data related interrupts, include data transfer
complete interrupt, data timeout interrupt, data CRC interrupt, data end bit interrupt.
Always trigger software timeout issue. Even reset the USDHC through bits in register
SYS_CTRL (0x2C, bit28 reset tuning, bit26 reset data, bit 25 reset command, bit 24
reset all) can't recover this. From the user's point of view, USDHC stuck, SD can't
be recognized any more.
Fixes: d9370424c9 ("mmc: sdhci-esdhc-imx: reset tuning circuit when power on mmc card")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1634263236-6111-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92b18252b9 upstream.
While mmc0 enter suspend state, we need halt CQE to send legacy cmd(flush
cache) and disable cqe, for resume back, we enable CQE and not clear HALT
state.
In this case MediaTek mmc host controller will keep the value for HALT
state after CQE disable/enable flow, so the next CQE transfer after resume
will be timeout due to CQE is in HALT state, the log as below:
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: timeout for tag 2
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: ============ CQHCI REGISTER DUMP ===========
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Caps: 0x100020b6 | Version: 0x00000510
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Config: 0x00001103 | Control: 0x00000001
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Int stat: 0x00000000 | Int enab: 0x00000006
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Int sig: 0x00000006 | Int Coal: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: TDL base: 0xfd05f000 | TDL up32: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Doorbell: 0x8000203c | TCN: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Dev queue: 0x00000000 | Dev Pend: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Task clr: 0x00000000 | SSC1: 0x00001000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: SSC2: 0x00000001 | DCMD rsp: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: RED mask: 0xfdf9a080 | TERRI: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Resp idx: 0x00000000 | Resp arg: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: CRNQP: 0x00000000 | CRNQDUN: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: CRNQIS: 0x00000000 | CRNQIE: 0x00000000
This change check HALT state after CQE enable, if CQE is in HALT state, we
will clear it.
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Cc: stable@vger.kernel.org
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: a4080225f5 ("mmc: cqhci: support for command queue enabled host")
Link: https://lore.kernel.org/r/20211026070812.9359-1-wenbin.mei@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da353fac65 upstream.
sk->sk_err appears to expect a positive value, a convention that ktls
doesn't always follow and that leads to memory corruption in other code.
For instance,
[kworker]
tls_encrypt_done(..., err=<negative error from crypto request>)
tls_err_abort(.., err)
sk->sk_err = err;
[task]
splice_from_pipe_feed
...
tls_sw_do_sendpage
if (sk->sk_err) {
ret = -sk->sk_err; // ret is positive
splice_from_pipe_feed (continued)
ret = actor(...) // ret is still positive and interpreted as bytes
// written, resulting in underflow of buf->len and
// sd->len, leading to huge buf->offset and bogus
// addresses computed in later calls to actor()
Fix all tls_err_abort() callers to pass a negative error code
consistently and centralize the error-prone sign flip there, throwing in
a warning to catch future misuse and uninlining the function so it
really does only warn once.
Cc: stable@vger.kernel.org
Fixes: c46234ebb4 ("tls: RX path for ktls")
Reported-by: syzbot+b187b77c8474f9648fae@syzkaller.appspotmail.com
Signed-off-by: Daniel Jordan <daniel.m.jordan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2195f2062e upstream.
During probing, the driver tries to get a list (mask) of supported
command types in port100_get_command_type_mask() function. The value
is u64 and 0 is treated as invalid mask (no commands supported). The
function however returns also -ERRNO as u64 which will be interpret as
valid command mask.
Return 0 on every error case of port100_get_command_type_mask(), so the
probing will stop.
Cc: <stable@vger.kernel.org>
Fixes: 0347a6ab30 ("NFC: port100: Commands mechanism implementation")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fa40d9734a upstream.
The function tipc_crypto_key_rcv is used to parse MSG_CRYPTO messages
to receive keys from other nodes in the cluster in order to decrypt any
further messages from them.
This patch verifies that any supplied sizes in the message body are
valid for the received message.
Fixes: 1ef6f7c939 ("tipc: add automatic session key exchange")
Signed-off-by: Max VA <maxv@sentinelone.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a0023bb9dd upstream.
mv_init_host() propagates the value returned by mv_chip_id() which in turn
gets propagated by mv_pci_init_one() and hits local_pci_probe().
During the process of driver probing, the probe function should return < 0
for failure, otherwise, the kernel will treat value > 0 as success.
Since this is a bug rather than a recoverable runtime error we should
use dev_alert() instead of dev_err().
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e5a04be88 upstream.
Some systems such as the Microsoft Surface Laptop 4 leave interrupts
enabled and configured for use in sleep states on boot, which cause
unexpected behaviour such as spurious wakes and failed resumes in
s2idle states.
As interrupts should not be enabled until they are claimed and
explicitly enabled, disabling any interrupts mistakenly left enabled by
firmware should be safe.
Signed-off-by: Sachi King <nakato@nakato.io>
Link: https://lore.kernel.org/r/20211009033240.21543-1-nakato@nakato.io
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6dba4bdfd7 upstream.
This reverts commit a49d784d5a.
The updated binding was wrong / invalid and has been reverted. There
isn't any upstream kernel DTS using it and Broadcom isn't known to use
it neither. There is close to zero chance this will cause regression for
anyone.
Actually in-kernel bcm5301x.dtsi still uses the old good binding and so
it's broken since the driver update. This revert fixes it.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20211008205938.29925-3-zajec5@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 295cf15623 upstream.
Al reminds us that the usercopy API must only return complete failure
if absolutely nothing could be copied. Currently, if userspace does
something silly like giving us an unaligned pointer to Device memory,
or a size which overruns MTE tag bounds, we may fail to honour that
requirement when faulting on a multi-byte access even though a smaller
access could have succeeded.
Add a mitigation to the fixup routines to fall back to a single-byte
copy if we faulted on a larger access before anything has been written
to the destination, to guarantee making *some* forward progress. We
needn't be too concerned about the overall performance since this should
only occur when callers are doing something a bit dodgy in the first
place. Particularly broken userspace might still be able to trick
generic_perform_write() into an infinite loop by targeting write() at
an mmap() of some read-only device register where the fault-in load
succeeds but any store synchronously aborts such that copy_to_user() is
genuinely unable to make progress, but, well, don't do that...
CC: stable@vger.kernel.org
Reported-by: Chen Huang <chenhuang5@huawei.com>
Suggested-by: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/dc03d5c675731a1f24a62417dba5429ad744234e.1626098433.git.robin.murphy@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Chen Huang <chenhuang5@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 792bb6eb86 upstream.
[ 97.866748] a.out/2890 is trying to acquire lock:
[ 97.867829] ffff8881046763e8 (&ctx->uring_lock){+.+.}-{3:3}, at:
io_wq_submit_work+0x155/0x240
[ 97.869735]
[ 97.869735] but task is already holding lock:
[ 97.871033] ffff88810dfe0be8 (&ctx->uring_lock){+.+.}-{3:3}, at:
__x64_sys_io_uring_enter+0x3f0/0x5b0
[ 97.873074]
[ 97.873074] other info that might help us debug this:
[ 97.874520] Possible unsafe locking scenario:
[ 97.874520]
[ 97.875845] CPU0
[ 97.876440] ----
[ 97.877048] lock(&ctx->uring_lock);
[ 97.877961] lock(&ctx->uring_lock);
[ 97.878881]
[ 97.878881] *** DEADLOCK ***
[ 97.878881]
[ 97.880341] May be due to missing lock nesting notation
[ 97.880341]
[ 97.881952] 1 lock held by a.out/2890:
[ 97.882873] #0: ffff88810dfe0be8 (&ctx->uring_lock){+.+.}-{3:3}, at:
__x64_sys_io_uring_enter+0x3f0/0x5b0
[ 97.885108]
[ 97.885108] stack backtrace:
[ 97.890457] Call Trace:
[ 97.891121] dump_stack+0xac/0xe3
[ 97.891972] __lock_acquire+0xab6/0x13a0
[ 97.892940] lock_acquire+0x2c3/0x390
[ 97.894894] __mutex_lock+0xae/0x9f0
[ 97.901101] io_wq_submit_work+0x155/0x240
[ 97.902112] io_wq_cancel_cb+0x162/0x490
[ 97.904126] io_async_find_and_cancel+0x3b/0x140
[ 97.905247] io_issue_sqe+0x86d/0x13e0
[ 97.909122] __io_queue_sqe+0x10b/0x550
[ 97.913971] io_queue_sqe+0x235/0x470
[ 97.914894] io_submit_sqes+0xcce/0xf10
[ 97.917872] __x64_sys_io_uring_enter+0x3fb/0x5b0
[ 97.921424] do_syscall_64+0x2d/0x40
[ 97.922329] entry_SYSCALL_64_after_hwframe+0x44/0xa9
While holding uring_lock, e.g. from inline execution, async cancel
request may attempt cancellations through io_wq_submit_work, which may
try to grab a lock. Delay it to task_work, so we do it from a clean
context and don't have to worry about locking.
Cc: <stable@vger.kernel.org> # 5.5+
Fixes: c07e671951 ("io_uring: hold uring_lock while completing failed polled io in io_wq_submit_work()")
Reported-by: Abaci <abaci@linux.alibaba.com>
Reported-by: Hao Xu <haoxu@linux.alibaba.com>
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
[Lee: The first hunk solves a different (double free) issue in v5.10.
Only the first hunk of the original patch is relevant to v5.10 AND
the first hunk of the original patch is only relevant to v5.10]
Reported-by: syzbot+59d8a1f4e60c20c066cf@syzkaller.appspotmail.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 48ccc8edf5 upstream.
In randconfig builds, we sometimes come across this warning:
arm-linux-gnueabi-ld: XIP start address may cause MPU programming issues
While this is helpful for actual systems to figure out why it
fails, the warning does not provide any benefit for build testing,
so guard it in a check for CONFIG_COMPILE_TEST, which is usually
set on randconfig builds.
Fixes: 216218308c ("ARM: 8713/1: NOMMU: Support MPU in XIP configuration")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 44cc6412e6 upstream.
When frame pointers are used instead of the ARM unwinder,
and the kernel is built using clang with an external assembler
and CONFIG_XIP_KERNEL, every file produces two warnings
like:
arm-linux-gnueabi-ld: warning: orphan section `.ARM.extab' from `net/mac802154/util.o' being placed in section `.ARM.extab'
arm-linux-gnueabi-ld: warning: orphan section `.ARM.exidx' from `net/mac802154/util.o' being placed in section `.ARM.exidx'
The same fix was already merged for the normal (non-XIP)
linker script, with a longer description.
Fixes: c39866f268 ("arm/build: Always handle .ARM.exidx and .ARM.extab sections")
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eaf6cc7165 upstream.
Both the decompressor code and the kasan logic try to override
the memcpy() and memmove() definitions, which leading to a clash
in a KASAN-enabled kernel with XZ decompression:
arch/arm/boot/compressed/decompress.c:50:9: error: 'memmove' macro redefined [-Werror,-Wmacro-redefined]
#define memmove memmove
^
arch/arm/include/asm/string.h:59:9: note: previous definition is here
#define memmove(dst, src, len) __memmove(dst, src, len)
^
arch/arm/boot/compressed/decompress.c:51:9: error: 'memcpy' macro redefined [-Werror,-Wmacro-redefined]
#define memcpy memcpy
^
arch/arm/include/asm/string.h:58:9: note: previous definition is here
#define memcpy(dst, src, len) __memcpy(dst, src, len)
^
Here we want the set of functions from the decompressor, so undefine
the other macros before the override.
Link: https://lore.kernel.org/linux-arm-kernel/CACRpkdZYJogU_SN3H9oeVq=zJkRgRT1gDz3xp59gdqWXxw-B=w@mail.gmail.com/
Link: https://lore.kernel.org/lkml/202105091112.F5rmd4By-lkp@intel.com/
Fixes: d6d51a96c7 ("ARM: 9014/2: Replace string mem* functions for KASan")
Fixes: a7f464f3db ("ARM: 7001/2: Wire up support for the XZ decompressor")
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df909df077 upstream.
ARM: kasan: Fix __get_user_check failure with kasan
In macro __get_user_check defined in arch/arm/include/asm/uaccess.h,
error code is store in register int __e(r0). When kasan is
enabled, assigning value to kernel address might trigger kasan check,
which unexpectedly overwrites r0 and causes undefined behavior on arm
kasan images.
One example is failure in do_futex and results in process soft lockup.
Log:
watchdog: BUG: soft lockup - CPU#0 stuck for 62946ms! [rs:main
Q:Reg:1151]
...
(__asan_store4) from (futex_wait_setup+0xf8/0x2b4)
(futex_wait_setup) from (futex_wait+0x138/0x394)
(futex_wait) from (do_futex+0x164/0xe40)
(do_futex) from (sys_futex_time32+0x178/0x230)
(sys_futex_time32) from (ret_fast_syscall+0x0/0x50)
The soft lockup happens in function futex_wait_setup. The reason is
function get_futex_value_locked always return EINVAL, thus pc jump
back to retry label and causes looping.
This line in function get_futex_value_locked
ret = __get_user(*dest, from);
is expanded to
*dest = (typeof(*(p))) __r2; ,
in macro __get_user_check. Writing to pointer dest triggers kasan check
and overwrites the return value of __get_user_x function.
The assembly code of get_futex_value_locked in kernel/futex.c:
...
c01f6dc8: eb0b020e bl c04b7608 <__get_user_4>
// "x = (typeof(*(p))) __r2;" triggers kasan check and r0 is overwritten
c01f6dCc: e1a00007 mov r0, r7
c01f6dd0: e1a05002 mov r5, r2
c01f6dd4: eb04f1e6 bl c0333574 <__asan_store4>
c01f6dd8: e5875000 str r5, [r7]
// save ret value of __get_user(*dest, from), which is dest address now
c01f6ddc: e1a05000 mov r5, r0
...
// checking return value of __get_user failed
c01f6e00: e3550000 cmp r5, #0
...
c01f6e0c: 01a00005 moveq r0, r5
// assign return value to EINVAL
c01f6e10: 13e0000d mvnne r0, #13
Return value is the destination address of get_user thus certainly
non-zero, so get_futex_value_locked always return EINVAL.
Fix it by using a tmp vairable to store the error code before the
assignment. This fix has no effects to non-kasan images thanks to compiler
optimization. It only affects cases that overwrite r0 due to kasan check.
This should fix bug discussed in Link:
[1] https://lore.kernel.org/linux-arm-kernel/0ef7c2a5-5d8b-c5e0-63fa-31693fd4495c@gmail.com/
Fixes: 421015713b ("ARM: 9017/2: Enable KASan for ARM")
Signed-off-by: Lexi Shao <shaolexi@huawei.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the ability to load the names of alternative firmwares from the
Device Tree node. This permits separate firmwares for 43436s and 43438
and allows downstream firmwares to coexist with upstream.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
This reverts commit c52581ffa4.
Replace the hardcoded alternate firmware names with mappings provided
from Device Tree.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Add an option to enable configuration via the Media Controller API
(rather than the video-node-centric /dev/videoN) as about to
be used by libcamera as it enables more complex pipelines to be
handled.
Any source that has a libcamera tuning merged has MC enabled by
default.
Sources with no libcamera tuning merged have it disabled by
default.
In either case it can be overridden with the overlay parameter
"media-controller".
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
BCM43430/2 may be BCM43430B0 or BCM43436P, and BCM43430/1 can be either
BCM43430A1 or BCM43436S, the former being upstream names and the
latter downstream names for differently-sourced sister parts.
Make the choice of firmwares board-specific (without making the actual
firmwares board-specific) by placing the alternative firmware names for
each part in the DT node.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Add the ability to load the names of alternative firmwares from the
Device Tree node. This permits separate firmwares for 43436s and 43438
and allows downstream firmwares to coexist with upstream.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
This reverts commit c52581ffa4.
Replace the hardcoded alternate firmware names with mappings provided
from Device Tree.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
An unwanted side effect of enabling the BRCMDBG config setting is
redefining brcmf_info to be brcmf_err. This can be alarming to users
and makes it harder to spot real errors, so don't do it.
See: https://github.com/raspberrypi/linux/issues/4663
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Retain the old names for backwards compatibility for a while, while the
necessary firmware change rolls out.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Add predefined modelines for the 240p (NTSC) and 288p (PAL) progressive
modes, and report them through vc4_vec_connector_get_modes().
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Make vc4_vec_encoder_atomic_check() accept arbitrary modelines, as long
as they result in somewhat sane output from the VEC. The bounds have
been determined empirically. Additionally, add support for the
progressive 262-line and 312-line modes.
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
trigger_mode == 0 (default) => no effect / no registers written
trigger_mode == 1 => source
trigger_mode == 2 => sink
This can be set e.g. in /boot/cmdline.txt as imx477.trigger_mode=N
Signed-off-by: Jonas Jacob <jonas.jacob@neocortexvision.com>
commit aaac373317 upstream.
Replace the open coded calculations of the actual physical address
of the KVM stub vector table with a single adr_l invocation.
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
commit 3bcf906b19 upstream.
Replace the open coded arithmetic with a simple adr_l/sub pair. This
removes some open coded arithmetic involving virtual addresses, avoids
literal pools on v7+, and slightly reduces the footprint of the code.
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
commit d74d2b2250 upstream.
Replace the open coded PC relative offset calculations with adr_l and
ldr_l invocations. This removes some open coded PC relative arithmetic,
avoids literal pools on v7+, and slightly reduces the footprint of the
code. Note that ALT_SMP() expects a single instruction so move the macro
invocation after it.
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
commit 59d2f2827d upstream.
Now that calling __do_fixup_smp_on_up() can be done without passing
the physical-to-virtual offset in r3, we can replace the open coded
PC relative offset calculations with a pair of adr_l invocations. This
removes some open coded arithmetic involving virtual addresses, avoids
literal pools on v7+, and slightly reduces the footprint of the code.
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
commit 450abd38fe upstream.
Currently, the .alt.smp.init section contains the virtual addresses
of the patch sites. Since patching may occur both before and after
switching into virtual mode, this requires some manual handling of
the address when applying the UP alternative.
Let's simplify this by using relative offsets in the table entries:
this allows us to simply add each entry's address to its contents,
regardless of whether we are running in virtual mode or not.
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
commit 91580f0dbf upstream.
Replace the open coded PC relative offset calculations with adr_l
and ldr_l invocations. This removes some open coded arithmetic
involving virtual addresses, avoids literal pools on v7+, and slightly
reduces the footprint of the code.
Note that it also removes a stale comment about the contents of r6.
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
commit 172c34c9ff upstream.
Replace the open coded PC relative offset calculations involving
__turn_mmu_on and __turn_mmu_on_end with a pair of adr_l invocations.
This removes some open coded arithmetic involving virtual addresses,
avoids literal pools on v7+, and slightly reduces the footprint of the
code.
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
commit 62c4a2e202 upstream.
Replace the open coded PC relative offset calculations with a pair of
adr_l invocations. This removes some open coded arithmetic involving
virtual addresses, avoids literal pools on v7+, and slightly reduces
the footprint of the code.
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
commit 9443076e43 upstream.
The ARM kernel's linear map starts at PAGE_OFFSET, which maps to a
physical address (PHYS_OFFSET) that is platform specific, and is
discovered at boot. Since we don't want to slow down translations
between physical and virtual addresses by keeping the offset in a
variable in memory, we implement this by patching the code performing
the translation, and putting the offset between PAGE_OFFSET and the
start of physical RAM directly into the instruction opcodes.
As we only patch up to 8 bits of offset, yielding 4 GiB >> 8 == 16 MiB
of granularity, we have to round up PHYS_OFFSET to the next multiple if
the start of physical RAM is not a multiple of 16 MiB. This wastes some
physical RAM, since the memory that was skipped will now live below
PAGE_OFFSET, making it inaccessible to the kernel.
We can improve this by changing the patchable sequences and the patching
logic to carry more bits of offset: 11 bits gives us 4 GiB >> 11 == 2 MiB
of granularity, and so we will never waste more than that amount by
rounding up the physical start of DRAM to the next multiple of 2 MiB.
(Note that 2 MiB granularity guarantees that the linear mapping can be
created efficiently, whereas less than 2 MiB may result in the linear
mapping needing another level of page tables)
This helps Zhen Lei's scenario, where the start of DRAM is known to be
occupied. It also helps EFI boot, which relies on the firmware's page
allocator to allocate space for the decompressed kernel as low as
possible. And if the KASLR patches ever land for 32-bit, it will give
us 3 more bits of randomization of the placement of the kernel inside
the linear region.
For the ARM code path, it simply comes down to using two add/sub
instructions instead of one for the carryless version, and patching
each of them with the correct immediate depending on the rotation
field. For the LPAE calculation, which has to deal with a carry, it
patches the MOVW instruction with up to 12 bits of offset (but we only
need 11 bits anyway)
For the Thumb2 code path, patching more than 11 bits of displacement
would be somewhat cumbersome, but the 11 bits we need fit nicely into
the second word of the u16[2] opcode, so we simply update the immediate
assignment and the left shift to create an addend of the right magnitude.
Suggested-by: Zhen Lei <thunder.leizhen@huawei.com>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
commit e8e00f5afb upstream.
In preparation for reducing the phys-to-virt minimum relative alignment
from 16 MiB to 2 MiB, switch to patchable sequences involving MOVW
instructions that can more easily be manipulated to carry a 12-bit
immediate. Note that the non-LPAE ARM sequence is not updated: MOVW
may not be supported on non-LPAE platforms, and the sequence itself
can be updated more easily to apply the 12 bits of displacement.
For Thumb2, which has many more versions of opcodes, switch to a sequence
that can be patched by the same patching code for both versions. Note
that the Thumb2 opcodes for MOVW and MVN are unambiguous, and have no
rotation bits in their immediate fields, so there is no need to use
placeholder constants in the asm blocks.
While at it, drop the 'volatile' qualifiers from the asm blocks: the
code does not have any side effects that are invisible to the compiler,
so it is free to omit these sequences if the outputs are not used.
Suggested-by: Russell King <linux@armlinux.org.uk>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
commit 0e3db6c9d7 upstream.
Declutter the code in __fixup_pv_table() by using the new adr_l/str_l
macros to take PC relative references to external symbols, and by
using the value of PHYS_OFFSET passed in r8 to calculate the p2v
offset.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
commit 2730e8eaa4 upstream.
Free up a register in the p2v patching code by switching to relative
references, which don't require keeping the phys-to-virt displacement
live in a register.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
commit 7a94849e81 upstream.
The big and little endian versions of the ARM p2v patching routine only
differ in the values of the constants, so factor those out into macros
so that we only have one version of the logic sequence to maintain.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
commit 4b16421c3e upstream.
The ARM and Thumb2 versions of the p2v patching loop have some overlap
at the end of the loop, so factor that out. As numeric labels are not
required to be unique, and may therefore be ambiguous, use named local
labels for the start and end of the loop instead.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
commit eae78e1a97 upstream.
Move the phys2virt patching code into a separate .S file before doing
some work on it.
Suggested-by: Nicolas Pitre <nico@fluxnic.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
commit 22f2d23098 upstream.
When using the new adr_l/ldr_l/str_l macros to refer to external symbols
from modules, the linker may emit place relative ELF relocations that
need to be fixed up by the module loader. So add support for these.
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
The HVS Gamma block can only be updated when idle, so we need to disable
the HVS channel when the gamma property is set in an atomic commit.
Since the pixelvalve cannot have its assigned channel halted without
stalling unless it's disabled as well, in our case that means forcing a
full disable / enable cycle on the pipeline.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
BCM2711 changes from a 256 entry lookup table to a 16 point
piecewise linear function as the pipeline bitdepth has increased
to make a LUT unwieldy.
Implement a simple conversion from a 256 entry LUT that userspace
is likely to expect to 16 evenly spread points in the PWL. This
could be improved with curve fitting at a later date.
Co-developed-by: Juerg Haefliger <juergh@canonical.com>
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
clk-2835 is deprecated and gets an innacurate clock for VEC (107MHz).
Switch to clk-raspberrypi which uses the right PLL to get an accurate 108MHz.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
commit 9d417cbe36 upstream.
tglx notes:
This function [futex_detect_cmpxchg] is only needed when an
architecture has to runtime discover whether the CPU supports it or
not. ARM has unconditional support for this, so the obvious thing to
do is the below.
Fixes linkage failure from Clang randconfigs:
kernel/futex.o:(.text.fixup+0x5c): relocation truncated to fit: R_ARM_JUMP24 against `.init.text'
and boot failures for CONFIG_THUMB2_KERNEL.
Link: https://github.com/ClangBuiltLinux/linux/issues/325
Comments from Nick Desaulniers:
See-also: 03b8c7b623 ("futex: Allow architectures to skip
futex_atomic_cmpxchg_inatomic() test")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Nathan Chancellor <nathan@kernel.org>
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org # v3.14+
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 183d9ebd44 ("selftests/bpf: Fix core_reloc test runner") causes
builds of selftests/bpf to fail on 5.10.y since the branch doesn't have the
ASSERT_FALSE macro yet. Replace ASSERT_FALSE with ASSERT_EQ.
Fixes: 183d9ebd44 ("selftests/bpf: Fix core_reloc test runner")
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed65df63a3 upstream.
While writing an email explaining the "bit = 0" logic for a discussion on
making ftrace_test_recursion_trylock() disable preemption, I discovered a
path that makes the "not do the logic if bit is zero" unsafe.
The recursion logic is done in hot paths like the function tracer. Thus,
any code executed causes noticeable overhead. Thus, tricks are done to try
to limit the amount of code executed. This included the recursion testing
logic.
Having recursion testing is important, as there are many paths that can
end up in an infinite recursion cycle when tracing every function in the
kernel. Thus protection is needed to prevent that from happening.
Because it is OK to recurse due to different running context levels (e.g.
an interrupt preempts a trace, and then a trace occurs in the interrupt
handler), a set of bits are used to know which context one is in (normal,
softirq, irq and NMI). If a recursion occurs in the same level, it is
prevented*.
Then there are infrastructure levels of recursion as well. When more than
one callback is attached to the same function to trace, it calls a loop
function to iterate over all the callbacks. Both the callbacks and the
loop function have recursion protection. The callbacks use the
"ftrace_test_recursion_trylock()" which has a "function" set of context
bits to test, and the loop function calls the internal
trace_test_and_set_recursion() directly, with an "internal" set of bits.
If an architecture does not implement all the features supported by ftrace
then the callbacks are never called directly, and the loop function is
called instead, which will implement the features of ftrace.
Since both the loop function and the callbacks do recursion protection, it
was seemed unnecessary to do it in both locations. Thus, a trick was made
to have the internal set of recursion bits at a more significant bit
location than the function bits. Then, if any of the higher bits were set,
the logic of the function bits could be skipped, as any new recursion
would first have to go through the loop function.
This is true for architectures that do not support all the ftrace
features, because all functions being traced must first go through the
loop function before going to the callbacks. But this is not true for
architectures that support all the ftrace features. That's because the
loop function could be called due to two callbacks attached to the same
function, but then a recursion function inside the callback could be
called that does not share any other callback, and it will be called
directly.
i.e.
traced_function_1: [ more than one callback tracing it ]
call loop_func
loop_func:
trace_recursion set internal bit
call callback
callback:
trace_recursion [ skipped because internal bit is set, return 0 ]
call traced_function_2
traced_function_2: [ only traced by above callback ]
call callback
callback:
trace_recursion [ skipped because internal bit is set, return 0 ]
call traced_function_2
[ wash, rinse, repeat, BOOM! out of shampoo! ]
Thus, the "bit == 0 skip" trick is not safe, unless the loop function is
call for all functions.
Since we want to encourage architectures to implement all ftrace features,
having them slow down due to this extra logic may encourage the
maintainers to update to the latest ftrace features. And because this
logic is only safe for them, remove it completely.
[*] There is on layer of recursion that is allowed, and that is to allow
for the transition between interrupt context (normal -> softirq ->
irq -> NMI), because a trace may occur before the context update is
visible to the trace recursion logic.
Link: https://lore.kernel.org/all/609b565a-ed6e-a1da-f025-166691b5d994@linux.alibaba.com/
Link: https://lkml.kernel.org/r/20211018154412.09fcad3c@gandalf.local.home
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <James.Bottomley@hansenpartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Miroslav Benes <mbenes@suse.cz>
Cc: Joe Lawrence <joe.lawrence@redhat.com>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: "Peter Zijlstra (Intel)" <peterz@infradead.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Jisheng Zhang <jszhang@kernel.org>
Cc: =?utf-8?b?546L6LSH?= <yun.wang@linux.alibaba.com>
Cc: Guo Ren <guoren@kernel.org>
Cc: stable@vger.kernel.org
Fixes: edc15cafcb ("tracing: Avoid unnecessary multiple recursion checks")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a46044a92a upstream.
Since commit 2a671f77ee ("s390/pci: fix use after free of zpci_dev")
the reference count of a zpci_dev is incremented between
pcibios_add_device() and pcibios_release_device() which was supposed to
prevent the zpci_dev from being freed while the common PCI code has
access to it. It was missed however that the handling of zPCI
availability events assumed that once zpci_zdev_put() was called no
later availability event would still see the device. With the previously
mentioned commit however this assumption no longer holds and we must
make sure that we only drop the initial long-lived reference the zPCI
subsystem holds exactly once.
Do so by introducing a zpci_device_reserved() function that handles when
a device is reserved. Here we make sure the zpci_dev will not be
considered for further events by removing it from the zpci_list.
This also means that the device actually stays in the
ZPCI_FN_STATE_RESERVED state between the time we know it has been
reserved and the final reference going away. We thus need to consider it
a real state instead of just a conceptual state after the removal. The
final cleanup of PCI resources, removal from zbus, and destruction of
the IOMMU stays in zpci_release_device() to make sure holders of the
reference do see valid data until the release.
Fixes: 2a671f77ee ("s390/pci: fix use after free of zpci_dev")
Cc: stable@vger.kernel.org
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 43a08c3bda upstream.
When isotp_sendmsg() concurrent, tx.state of all TX processes can be
ISOTP_IDLE. The conditions so->tx.state != ISOTP_IDLE and
wq_has_sleeper(&so->wait) can not protect TX buffer from being
accessed by multiple TX processes.
We can use cmpxchg() to try to modify tx.state to ISOTP_SENDING firstly.
If the modification of the previous process succeed, the later process
must wait tx.state to ISOTP_IDLE firstly. Thus, we can ensure TX buffer
is accessed by only one process at the same time. And we should also
restore the original tx.state at the subsequent error processes.
Fixes: e057dd3fc2 ("can: add ISO 15765-2:2016 transport protocol")
Link: https://lore.kernel.org/all/c2517874fbdf4188585cf9ddf67a8fa74d5dbde5.1633764159.git.william.xuanziyang@huawei.com
Cc: stable@vger.kernel.org
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9f9f0f1999 ]
rx unused desc is the desc that need attatching new buffer
before refilling to hw to receive new packet, the number of
desc need attatching new buffer is calculated using next_to_use
and next_to_clean. when next_to_use == next_to_clean, currently
hns3 driver assumes that all the desc has the buffer attatched,
but 'next_to_use == next_to_clean' also means all the desc need
attatching new buffer if hw has comsumed all the desc and the
driver has not attatched any buffer to the desc yet.
This patch adds 'refill' in desc_cb to indicate whether a new
buffer has been refilled to a desc.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63acd42c0d ]
Commit f1a0a376ca ("sched/core: Initialize the idle task with
preemption disabled") removed the init_idle() call from
idle_thread_get(). This was the sole call-path on hotplug that resets
the Shadow Call Stack (scs) Stack Pointer (sp).
Not resetting the scs-sp leads to scs overflow after enough hotplug
cycles. Therefore add an explicit scs_task_reset() to the hotplug code
to make sure the scs-sp does get reset on hotplug.
Fixes: f1a0a376ca ("sched/core: Initialize the idle task with preemption disabled")
Signed-off-by: Woody Lin <woodylin@google.com>
[peterz: Changelog]
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Link: https://lore.kernel.org/r/20211012083521.973587-1-woodylin@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7fb223d0ad ]
Commit 8c0eb596ba ("[SCSI] qla2xxx: Fix a memory leak in an error path of
qla2x00_process_els()"), intended to change:
bsg_job->request->msgcode == FC_BSG_HST_ELS_NOLOGIN
to:
bsg_job->request->msgcode != FC_BSG_RPT_ELS
but changed it to:
bsg_job->request->msgcode == FC_BSG_RPT_ELS
instead.
Change the == to a != to avoid leaking the fcport structure or freeing
unallocated memory.
Link: https://lore.kernel.org/r/20211012191834.90306-2-jgu@purestorage.com
Fixes: 8c0eb596ba ("[SCSI] qla2xxx: Fix a memory leak in an error path of qla2x00_process_els()")
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Joy Gu <jgu@purestorage.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 187a580c9e ]
In commit 9e67600ed6 ("scsi: iscsi: Fix race condition between login and
sync thread") we meant to add a check where before we call ->set_param() we
make sure the iscsi_cls_connection is bound. The problem is that between
versions 4 and 5 of the patch the deletion of the unchecked set_param()
call was dropped so we ended up with 2 calls. As a result we can still hit
a crash where we access the unbound connection on the first call.
This patch removes that first call.
Fixes: 9e67600ed6 ("scsi: iscsi: Fix race condition between login and sync thread")
Link: https://lore.kernel.org/r/20211010161904.60471-1-michael.christie@oracle.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Li Feng <fengli@smartx.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d997cc1715 ]
On i.MX7S and i.MX8M* (but not i.MX6*) the pwrkey device has an
associated clock. Accessing the registers requires that this clock is
enabled. Binding the driver on at least i.MX7S and i.MX8MP while not
having the clock enabled results in a complete hang of the machine.
(This usually only happens if snvs_pwrkey is built as a module and the
rtc-snvs driver isn't already bound because at bootup the required clk
is on and only gets disabled when the clk framework disables unused clks
late during boot.)
This completes the fix in commit 135be16d35 ("ARM: dts: imx7s: add
snvs clock to pwrkey").
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211013062848.2667192-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ff6d64e68 ]
The `cpu` argument of perf_evsel__read() must specify the cpu index.
perf_cpu_map__for_each_cpu() is for iterating the cpu number (not index)
and is thus not appropriate for use with perf_evsel__read().
So, if there is an offline CPU, the cpu number specified in the argument
may point out of range because the cpu number and the cpu index are
different.
Fix test_stat_cpu().
Testing it:
# make tests -C tools/lib/perf/
make: Entering directory '/home/nakamura/kernel_src/linux-5.15-rc4_fix/tools/lib/perf'
running static:
- running tests/test-cpumap.c...OK
- running tests/test-threadmap.c...OK
- running tests/test-evlist.c...OK
- running tests/test-evsel.c...OK
running dynamic:
- running tests/test-cpumap.c...OK
- running tests/test-threadmap.c...OK
- running tests/test-evlist.c...OK
- running tests/test-evsel.c...OK
make: Leaving directory '/home/nakamura/kernel_src/linux-5.15-rc4_fix/tools/lib/perf'
Signed-off-by: Shunsuke Nakamura <nakamura.shun@fujitsu.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20211011083704.4108720-1-nakamura.shun@fujitsu.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b37a15188e ]
The snd_hdac_bus_reset_link() contains logic to clear STATESTS register
before performing controller reset. This code dates back to an old
bugfix in commit e8a7f136f5 ("[ALSA] hda-intel - Improve HD-audio
codec probing robustness"). Originally the code was added to
azx_reset().
The code was moved around in commit a41d122449 ("ALSA: hda - Embed bus
into controller object") and ended up to snd_hdac_bus_reset_link() and
called primarily via snd_hdac_bus_init_chip().
The logic to clear STATESTS is correct when snd_hdac_bus_init_chip() is
called when controller is not in reset. In this case, STATESTS can be
cleared. This can be useful e.g. when forcing a controller reset to retry
codec probe. A normal non-power-on reset will not clear the bits.
However, this old logic is problematic when controller is already in
reset. The HDA specification states that controller must be taken out of
reset before writing to registers other than GCTL.CRST (1.0a spec,
3.3.7). The write to STATESTS in snd_hdac_bus_reset_link() will be lost
if the controller is already in reset per the HDA specification mentioned.
This has been harmless on older hardware. On newer generation of Intel
PCIe based HDA controllers, if configured to report issues, this write
will emit an unsupported request error. If ACPI Platform Error Interface
(APEI) is enabled in kernel, this will end up to kernel log.
Fix the code in snd_hdac_bus_reset_link() to only clear the STATESTS if
the function is called when controller is not in reset. Otherwise
clearing the bits is not possible and should be skipped.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211012142935.3731820-1-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6636fec29c ]
On SPEAr3xx, ethernet driver is not compatible with the SPEAr600
one.
Indeed, SPEAr3xx uses an earlier version of this IP (v3.40) and
needs some driver tuning compare to SPEAr600.
The v3.40 IP support was added to stmmac driver and this patch
fixes this issue and use the correct compatible string for
SPEAr3xx
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77a5b9e3d1 ]
Currently inode_in_dir() ignores errors returned from
btrfs_lookup_dir_index_item() and from btrfs_lookup_dir_item(), treating
any errors as if the directory entry does not exists in the fs/subvolume
tree, which is obviously not correct, as we can get errors such as -EIO
when reading extent buffers while searching the fs/subvolume's tree.
Fix that by making inode_in_dir() return the errors and making its only
caller, add_inode_ref(), deal with returned errors as well.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0f1886de7 ]
It seems that a few recent AMD systems show the codec configuration
errors at the early boot, while loading the driver at a later stage
works magically. Although the root cause of the error isn't clear,
it's certainly not bad to allow retrying the codec probe in such a
case if that helps.
This patch adds the capability for retrying the probe upon codec probe
errors on the certain AMD platforms. The probe_work is changed to a
delayed work, and at the secondary call, it'll jump to the codec
probing.
Note that, not only adding the re-probing, this includes the behavior
changes in the codec configuration function. Namely,
snd_hda_codec_configure() won't unregister the codec at errors any
longer. Instead, its caller, azx_codec_configure() unregisters the
codecs with the probe failures *if* any codec has been successfully
configured. If all codec probe failed, it doesn't unregister but let
it re-probed -- which is the most case we're seeing and this patch
tries to improve.
Even if the driver doesn't re-probe or give up, it will go to the
"free-all" error path, hence the leftover codecs shall be disabled /
deleted in anyway.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1190801
Link: https://lore.kernel.org/r/20211006141940.2897-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit adfb7b4966 upstream.
Currently the max tx size supported by the hw is calculated by
using the max BD num supported by the hw. According to the hw
user manual, the max tx size is fixed value for both non-TSO and
TSO skb.
This patch updates the max tx size according to the manual.
Fixes: 8ae10cfb5089("net: hns3: support tx-scatter-gather-fraglist feature")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fac3cb82a5 upstream.
When I added IGMPv3 support I decided to follow the RFC for computing
the GMI dynamically:
" 8.4. Group Membership Interval
The Group Membership Interval is the amount of time that must pass
before a multicast router decides there are no more members of a
group or a particular source on a network.
This value MUST be ((the Robustness Variable) times (the Query
Interval)) plus (one Query Response Interval)."
But that actually is inconsistent with how the bridge used to compute it
for IGMPv2, where it was user-configurable that has a correct default value
but it is up to user-space to maintain it. This would make it consistent
with the other timer values which are also maintained correct by the user
instead of being dynamically computed. It also changes back to the previous
user-expected GMI behaviour for IGMPv3 queries which were supported before
IGMPv3 was added. Note that to properly compute it dynamically we would
need to add support for "Robustness Variable" which is currently missing.
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Fixes: 0436862e41 ("net: bridge: mcast: support for IGMPv3/MLDv2 ALLOW_NEW_SOURCES report")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b1499a817 upstream.
The nci_core_conn_close_rsp_packet() function will release the conn_info
with given conn_id. However, it needs to set the rf_conn_info to NULL to
prevent other routines like nci_rf_intf_activated_ntf_packet() to trigger
the UAF.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a25dfa67f upstream.
Since commit c300ab9f08 ("KVM: x86: Replace late check_nested_events() hack with
more precise fix") there is no longer the certainty that check_nested_events()
tries to inject an external interrupt vmexit to L1 on every call to vcpu_enter_guest.
Therefore, even in that case we need to set KVM_REQ_EVENT. This ensures
that inject_pending_event() is called, and from there kvm_check_nested_events().
Fixes: c300ab9f08 ("KVM: x86: Replace late check_nested_events() hack with more precise fix")
Cc: stable@vger.kernel.org
Reviewed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 496c5fe25c upstream.
In isa206_idle_insn_mayloss() we store various registers into the stack
red zone, which is allowed.
However inside the IDLE_STATE_ENTER_SEQ_NORET macro we save r2 again,
to 0(r1), which corrupts the stack back chain.
We used to do the same in isa206_idle_insn_mayloss() itself, but we
fixed that in 73287caa92 ("powerpc64/idle: Fix SP offsets when saving
GPRs"), however we missed that the macro also corrupts the back chain.
Corrupting the back chain is bad for debuggability but doesn't
necessarily cause a bug.
However we recently changed the stack handling in some KVM code, and it
now relies on the stack back chain being valid when it returns. The
corruption causes that code to return with r1 pointing somewhere in
kernel data, at some point LR is restored from the stack and we branch
to NULL or somewhere else invalid.
Only affects Power8 hosts running KVM guests, with dynamic_mt_modes
enabled (which it is by default).
The fixes tag below points to the commit that changed the KVM stack
handling, exposing this bug. The actual corruption of the back chain has
always existed since 948cf67c47 ("powerpc: Add NAP mode support on
Power7 in HV mode").
Fixes: 9b4416c509 ("KVM: PPC: Book3S HV: Fix stack handling in idle_kvm_start_guest()")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211020094826.3222052-1-mpe@ellerman.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cdeb5d7d89 upstream.
We call idle_kvm_start_guest() from power7_offline() if the thread has
been requested to enter KVM. We pass it the SRR1 value that was returned
from power7_idle_insn() which tells us what sort of wakeup we're
processing.
Depending on the SRR1 value we pass in, the KVM code might enter the
guest, or it might return to us to do some host action if the wakeup
requires it.
If idle_kvm_start_guest() is able to handle the wakeup, and enter the
guest it is supposed to indicate that by returning a zero SRR1 value to
us.
That was the behaviour prior to commit 10d91611f4 ("powerpc/64s:
Reimplement book3s idle code in C"), however in that commit the
handling of SRR1 was reworked, and the zeroing behaviour was lost.
Returning from idle_kvm_start_guest() without zeroing the SRR1 value can
confuse the host offline code, causing the guest to crash and other
weirdness.
Fixes: 10d91611f4 ("powerpc/64s: Reimplement book3s idle code in C")
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211015133929.832061-2-mpe@ellerman.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b4416c509 upstream.
In commit 10d91611f4 ("powerpc/64s: Reimplement book3s idle code in
C") kvm_start_guest() became idle_kvm_start_guest(). The old code
allocated a stack frame on the emergency stack, but didn't use the
frame to store anything, and also didn't store anything in its caller's
frame.
idle_kvm_start_guest() on the other hand is written more like a normal C
function, it creates a frame on entry, and also stores CR/LR into its
callers frame (per the ABI). The problem is that there is no caller
frame on the emergency stack.
The emergency stack for a given CPU is allocated with:
paca_ptrs[i]->emergency_sp = alloc_stack(limit, i) + THREAD_SIZE;
So emergency_sp actually points to the first address above the emergency
stack allocation for a given CPU, we must not store above it without
first decrementing it to create a frame. This is different to the
regular kernel stack, paca->kstack, which is initialised to point at an
initial frame that is ready to use.
idle_kvm_start_guest() stores the backchain, CR and LR all of which
write outside the allocation for the emergency stack. It then creates a
stack frame and saves the non-volatile registers. Unfortunately the
frame it creates is not large enough to fit the non-volatiles, and so
the saving of the non-volatile registers also writes outside the
emergency stack allocation.
The end result is that we corrupt whatever is at 0-24 bytes, and 112-248
bytes above the emergency stack allocation.
In practice this has gone unnoticed because the memory immediately above
the emergency stack happens to be used for other stack allocations,
either another CPUs mc_emergency_sp or an IRQ stack. See the order of
calls to irqstack_early_init() and emergency_stack_init().
The low addresses of another stack are the top of that stack, and so are
only used if that stack is under extreme pressue, which essentially
never happens in practice - and if it did there's a high likelyhood we'd
crash due to that stack overflowing.
Still, we shouldn't be corrupting someone else's stack, and it is purely
luck that we aren't corrupting something else.
To fix it we save CR/LR into the caller's frame using the existing r1 on
entry, we then create a SWITCH_FRAME_SIZE frame (which has space for
pt_regs) on the emergency stack with the backchain pointing to the
existing stack, and then finally we switch to the new frame on the
emergency stack.
Fixes: 10d91611f4 ("powerpc/64s: Reimplement book3s idle code in C")
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211015133929.832061-1-mpe@ellerman.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 73287caa92 upstream.
The idle entry/exit code saves/restores GPRs in the stack "red zone"
(Protected Zone according to PowerPC64 ELF ABI v2). However, the offset
used for the first GPR is incorrect and overwrites the back chain - the
Protected Zone actually starts below the current SP. In practice this is
probably not an issue, but it's still incorrect so fix it.
Also expand the comments to explain why using the stack "red zone"
instead of creating a new stackframe is appropriate here.
Signed-off-by: Christopher M. Riedl <cmr@codefail.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210206072342.5067-1-cmr@codefail.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 342afce10d upstream.
Setting ds->num_ports to DSA_MAX_PORTS made DSA core allocate unnecessary
dsa_port's and call mt7530_port_disable for non-existent ports.
Set it to MT7530_NUM_PORTS to fix that, and dsa_is_user_port check in
port_enable/disable is no longer required.
Cc: stable@vger.kernel.org
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b15fa9224e upstream.
Starting with kernel 5.11 built with CONFIG_FORTIFY_SOURCE mouting an
ocfs2 filesystem with either o2cb or pcmk cluster stack fails with the
trace below. Problem seems to be that strings for cluster stack and
cluster name are not guaranteed to be null terminated in the disk
representation, while strlcpy assumes that the source string is always
null terminated. This causes a read outside of the source string
triggering the buffer overflow detection.
detected buffer overflow in strlen
------------[ cut here ]------------
kernel BUG at lib/string.c:1149!
invalid opcode: 0000 [#1] SMP PTI
CPU: 1 PID: 910 Comm: mount.ocfs2 Not tainted 5.14.0-1-amd64 #1
Debian 5.14.6-2
RIP: 0010:fortify_panic+0xf/0x11
...
Call Trace:
ocfs2_initialize_super.isra.0.cold+0xc/0x18 [ocfs2]
ocfs2_fill_super+0x359/0x19b0 [ocfs2]
mount_bdev+0x185/0x1b0
legacy_get_tree+0x27/0x40
vfs_get_tree+0x25/0xb0
path_mount+0x454/0xa20
__x64_sys_mount+0x103/0x140
do_syscall_64+0x3b/0xc0
entry_SYSCALL_64_after_hwframe+0x44/0xae
Link: https://lkml.kernel.org/r/20210929180654.32460-1-vvidic@valentin-vidic.from.hr
Signed-off-by: Valentin Vidic <vvidic@valentin-vidic.from.hr>
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5314454ea3 upstream.
Commit 6dbf7bb555 ("fs: Don't invalidate page buffers in
block_write_full_page()") uncovered a latent bug in ocfs2 conversion
from inline inode format to a normal inode format.
The code in ocfs2_convert_inline_data_to_extents() attempts to zero out
the whole cluster allocated for file data by grabbing, zeroing, and
dirtying all pages covering this cluster. However these pages are
beyond i_size, thus writeback code generally ignores these dirty pages
and no blocks were ever actually zeroed on the disk.
This oversight was fixed by commit 693c241a5f ("ocfs2: No need to zero
pages past i_size.") for standard ocfs2 write path, inline conversion
path was apparently forgotten; the commit log also has a reasoning why
the zeroing actually is not needed.
After commit 6dbf7bb555, things became worse as writeback code stopped
invalidating buffers on pages beyond i_size and thus these pages end up
with clean PageDirty bit but with buffers attached to these pages being
still dirty. So when a file is converted from inline format, then
writeback triggers, and then the file is grown so that these pages
become valid, the invalid dirtiness state is preserved,
mark_buffer_dirty() does nothing on these pages (buffers are already
dirty) but page is never written back because it is clean. So data
written to these pages is lost once pages are reclaimed.
Simple reproducer for the problem is:
xfs_io -f -c "pwrite 0 2000" -c "pwrite 2000 2000" -c "fsync" \
-c "pwrite 4000 2000" ocfs2_file
After unmounting and mounting the fs again, you can observe that end of
'ocfs2_file' has lost its contents.
Fix the problem by not doing the pointless zeroing during conversion
from inline format similarly as in the standard write path.
[akpm@linux-foundation.org: fix whitespace, per Joseph]
Link: https://lkml.kernel.org/r/20210930095405.21433-1-jack@suse.cz
Fixes: 6dbf7bb555 ("fs: Don't invalidate page buffers in block_write_full_page()")
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Tested-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Acked-by: Gang He <ghe@suse.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Jun Piao <piaojun@huawei.com>
Cc: "Markov, Andrey" <Markov.Andrey@Dell.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1bd85aa65d upstream.
Currently, we check the wb_err too early for directories, before all of
the unsafe child requests have been waited on. In order to fix that we
need to check the mapping->wb_err later nearer to the end of ceph_fsync.
We also have an overly-complex method for tracking errors after
blocklisting. The errors recorded in cleanup_session_requests go to a
completely separate field in the inode, but we end up reporting them the
same way we would for any other error (in fsync).
There's no real benefit to tracking these errors in two different
places, since the only reporting mechanism for them is in fsync, and
we'd need to advance them both every time.
Given that, we can just remove i_meta_err, and convert the places that
used it to instead just use mapping->wb_err instead. That also fixes
the original problem by ensuring that we do a check_and_advance of the
wb_err at the end of the fsync op.
Cc: stable@vger.kernel.org
URL: https://tracker.ceph.com/issues/52864
Reported-by: Patrick Donnelly <pdonnell@redhat.com>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Xiubo Li <xiubli@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98d0a6fb73 upstream.
Currently when mounting, we may end up finding an existing superblock
that corresponds to a blocklisted MDS client. This means that the new
mount ends up being unusable.
If we've found an existing superblock with a client that is already
blocklisted, and the client is not configured to recover on its own,
fail the match. Ditto if the superblock has been forcibly unmounted.
While we're in here, also rename "other" to the more conventional "fsc".
Cc: stable@vger.kernel.org
URL: https://bugzilla.redhat.com/show_bug.cgi?id=1901499
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4fbe70c5c upstream.
The receiver should abort TP if 'total message size' in TP.CM_RTS and
TP.CM_BAM is less than 9 or greater than 1785 [1], but currently the
j1939 stack only checks the upper bound and the receiver will accept
the following broadcast message:
vcan1 18ECFF00 [8] 20 08 00 02 FF 00 23 01
vcan1 18EBFF00 [8] 01 00 00 00 00 00 00 00
vcan1 18EBFF00 [8] 02 00 FF FF FF FF FF FF
This patch adds check for the lower bound and abort illegal TP.
[1] SAE-J1939-82 A.3.4 Row 2 and A.3.6 Row 6.
Fixes: 9d71dd0c70 ("can: add support of SAE J1939 protocol")
Link: https://lore.kernel.org/all/1634203601-3460-1-git-send-email-zhangchangzhong@huawei.com
Cc: stable@vger.kernel.org
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9acf636215 upstream.
Using wait_event_interruptible() to wait for complete transmission,
but do not check the result of wait_event_interruptible() which can be
interrupted. It will result in TX buffer has multiple accessors and
the later process interferes with the previous process.
Following is one of the problems reported by syzbot.
=============================================================
WARNING: CPU: 0 PID: 0 at net/can/isotp.c:840 isotp_tx_timer_handler+0x2e0/0x4c0
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.13.0-rc7+ #68
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1 04/01/2014
RIP: 0010:isotp_tx_timer_handler+0x2e0/0x4c0
Call Trace:
<IRQ>
? isotp_setsockopt+0x390/0x390
__hrtimer_run_queues+0xb8/0x610
hrtimer_run_softirq+0x91/0xd0
? rcu_read_lock_sched_held+0x4d/0x80
__do_softirq+0xe8/0x553
irq_exit_rcu+0xf8/0x100
sysvec_apic_timer_interrupt+0x9e/0xc0
</IRQ>
asm_sysvec_apic_timer_interrupt+0x12/0x20
Add result check for wait_event_interruptible() in isotp_sendmsg()
to avoid multiple accessers for tx buffer.
Fixes: e057dd3fc2 ("can: add ISO 15765-2:2016 transport protocol")
Link: https://lore.kernel.org/all/10ca695732c9dd267c76a3c30f37aefe1ff7e32f.1633764159.git.william.xuanziyang@huawei.com
Cc: stable@vger.kernel.org
Reported-by: syzbot+78bab6958a614b0c80b9@syzkaller.appspotmail.com
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3cb958027c ]
When utilizing End to End delay mechanism, the following error messages show up:
|root@ehl1:~# ptp4l --tx_timestamp_timeout=50 -H -i eno2 -E -m
|ptp4l[950.573]: selected /dev/ptp3 as PTP clock
|ptp4l[950.586]: port 1: INITIALIZING to LISTENING on INIT_COMPLETE
|ptp4l[950.586]: port 0: INITIALIZING to LISTENING on INIT_COMPLETE
|ptp4l[952.879]: port 1: new foreign master 001395.fffe.4897b4-1
|ptp4l[956.879]: selected best master clock 001395.fffe.4897b4
|ptp4l[956.879]: port 1: assuming the grand master role
|ptp4l[956.879]: port 1: LISTENING to GRAND_MASTER on RS_GRAND_MASTER
|ptp4l[962.017]: port 1: received DELAY_REQ without timestamp
|ptp4l[962.273]: port 1: received DELAY_REQ without timestamp
|ptp4l[963.090]: port 1: received DELAY_REQ without timestamp
Commit f2fb6b6275 ("net: stmmac: enable timestamp snapshot for required PTP
packets in dwmac v5.10a") already addresses this problem for the dwmac
v5.10. However, same holds true for all dwmacs above version v4.10. Correct the
check accordingly. Afterwards everything works as expected.
Tested on Intel Atom(R) x6414RE Processor.
Fixes: 14f347334b ("net: stmmac: Correctly take timestamp for PTPv2")
Fixes: f2fb6b6275 ("net: stmmac: enable timestamp snapshot for required PTP packets in dwmac v5.10a")
Suggested-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0dd8a25f35 ]
HNS3 driver includes hns3.ko, hnae3.ko and hclge.ko.
hns3.ko includes network stack and pci_driver, hclge.ko includes
HW device action, algo_ops and timer task, hnae3.ko includes some
register function.
When SRIOV is enable and hclge.ko is removed, HW device is unloaded
but VF still exists, PF will not reply VF mbx messages, and cause
errors.
This patch fix it by disable SRIOV before remove hclge.ko.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1385cc81ba ]
The task of VF reset is performed through the workqueue. It checks the
value of hdev->reset_pending to determine whether to exit the loop.
However, the value of hdev->reset_pending may also be assigned by
the interrupt function hclgevf_misc_irq_handle(), which may cause the
loop fail to exit and keep occupying the workqueue. This loop is not
necessary, so remove it and the workqueue will be rescheduled if the
reset needs to be retried or a new reset occurs.
Fixes: 1cc9bc6e58 ("net: hns3: split hclgevf_reset() into preparing and rebuilding part")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68752b24f5 ]
Currently when there is a rx page allocation failure, it is
possible that polling may be stopped if there is no more packet
to be reveiced, which may cause queue stall problem under memory
pressure.
This patch makes sure polling is scheduled again when there is
any rx page allocation failure, and polling will try to allocate
receive buffers until it succeeds.
Now the allocation retry is added, it is unnecessary to do the rx
page allocation at the end of rx cleaning, so remove it. And reset
the unused_count to zero after calling hns3_nic_alloc_rx_buffers()
to avoid calling hns3_nic_alloc_rx_buffers() repeatedly under
memory pressure.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 731797fdff ]
If ets dwrr bandwidth of tc is set to 0, the hardware will switch to SP
mode. In this case, this tc may occupy all the tx bandwidth if it has
huge traffic, so it violates the purpose of the user setting.
To fix this problem, limit the ets dwrr bandwidth must greater than 0.
Fixes: cacde272dd ("net: hns3: Add hclge_dcb module for the support of DCB feature")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b63fcaab95 ]
Currently, DWRR of tc will be initialized to a fixed value when this tc
is enabled, but it is not been reset to 0 when this tc is disabled. It
cause a problem that the DWRR of unused tc is not 0 after using tc tool
to add and delete multi-tc parameters.
For examples, after enabling 4 TCs and restoring to 1 TC by follow
tc commands:
$ tc qdisc add dev eth0 root mqprio num_tc 4 map 0 1 2 3 0 1 2 3 queues \
8@0 8@8 8@16 8@24 hw 1 mode channel
$ tc qdisc del dev eth0 root
Now there is just one TC is enabled for eth0, but the tc info querying by
debugfs is shown as follow:
$ cat /mnt/hns3/0000:7d:00.0/tm/tc_sch_info
enabled tc number: 1
weight_offset: 14
TC MODE WEIGHT
0 dwrr 100
1 dwrr 100
2 dwrr 100
3 dwrr 100
4 dwrr 0
5 dwrr 0
6 dwrr 0
7 dwrr 0
This patch fixes it by resetting DWRR of tc to 0 when tc is disabled.
Fixes: 848440544b ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 787252a10d ]
With PREEMPT_COUNT=y, when a CPU is offlined and then onlined again, we
get:
BUG: scheduling while atomic: swapper/1/0/0x00000000
no locks held by swapper/1/0.
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.15.0-rc2+ #100
Call Trace:
dump_stack_lvl+0xac/0x108
__schedule_bug+0xac/0xe0
__schedule+0xcf8/0x10d0
schedule_idle+0x3c/0x70
do_idle+0x2d8/0x4a0
cpu_startup_entry+0x38/0x40
start_secondary+0x2ec/0x3a0
start_secondary_prolog+0x10/0x14
This is because powerpc's arch_cpu_idle_dead() decrements the idle task's
preempt count, for reasons explained in commit a7c2bb8279 ("powerpc:
Re-enable preemption before cpu_die()"), specifically "start_secondary()
expects a preempt_count() of 0."
However, since commit 2c669ef697 ("powerpc/preempt: Don't touch the idle
task's preempt_count during hotplug") and commit f1a0a376ca ("sched/core:
Initialize the idle task with preemption disabled"), that justification no
longer holds.
The idle task isn't supposed to re-enable preemption, so remove the
vestigial preempt_enable() from the CPU offline path.
Tested with pseries and powernv in qemu, and pseries on PowerVM.
Fixes: 2c669ef697 ("powerpc/preempt: Don't touch the idle task's preempt_count during hotplug")
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211015173902.2278118-1-nathanl@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4cce60f15c ]
Both arch/nios2/ and drivers/mmc/host/tmio_mmc.c define a macro
with the name "CTL_STATUS". Change the one in arch/nios2/ to be
"CTL_FSTATUS" (flags status) to eliminate the build warning.
In file included from ../drivers/mmc/host/tmio_mmc.c:22:
drivers/mmc/host/tmio_mmc.h:31: warning: "CTL_STATUS" redefined
31 | #define CTL_STATUS 0x1c
arch/nios2/include/asm/registers.h:14: note: this is the location of the previous definition
14 | #define CTL_STATUS 0
Fixes: b31ebd8055 ("nios2: Nios2 registers")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66d262804a ]
I compared the register definitions with the D-Link DWR-966
GPL sources and found that the PUAFD field definition was
incorrect. This definition is unused and causes no issues.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86f1e3a848 ]
With net.ipv4.tcp_l3mdev_accept=1 it is possible for a listen socket to
accept connection from the same client address in different VRFs. It is
also possible to set different MD5 keys for these clients which differ
only in the tcpm_l3index field.
This appears to work when distinguishing between different VRFs but not
between non-VRF and VRF connections. In particular:
* tcp_md5_do_lookup_exact will match a non-vrf key against a vrf key.
This means that adding a key with l3index != 0 after a key with l3index
== 0 will cause the earlier key to be deleted. Both keys can be present
if the non-vrf key is added later.
* _tcp_md5_do_lookup can match a non-vrf key before a vrf key. This
casues failures if the passwords differ.
Fix this by making tcp_md5_do_lookup_exact perform an actual exact
comparison on l3index and by making __tcp_md5_do_lookup perfer
vrf-bound keys above other considerations like prefixlen.
Fixes: dea53bb80e ("tcp: Add l3index to tcp_md5sig_key and md5 functions")
Signed-off-by: Leonard Crestez <cdleonard@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46393d61a3 ]
Fix the following build/link error by adding a dependency on the CRC32
routines:
ld: drivers/net/usb/lan78xx.o: in function `lan78xx_set_multicast':
lan78xx.c:(.text+0x48cf): undefined reference to `crc32_le'
The actual use of crc32_le() comes indirectly through ether_crc().
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 174c376278 ]
Because the data pointer of net/ipv4/vs/debug_level is not updated per
netns, it must be marked as read-only in non-init netns.
Fixes: c6d2d445d8 ("IPVS: netns, final patch enabling network name space.")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a482c5e00a ]
In rt_mt6(), when it's a nonlinear skb, the 1st skb_header_pointer()
only copies sizeof(struct ipv6_rt_hdr) to _route that rh points to.
The access by ((const struct rt0_hdr *)rh)->reserved will overflow
the buffer. So this access should be moved below the 2nd call to
skb_header_pointer().
Besides, after the 2nd skb_header_pointer(), its return value should
also be checked, othersize, *rp may cause null-pointer-ref.
v1->v2:
- clean up some old debugging log.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4c2efa139 ]
Correct parameters order in call to ice_tunnel_idx_to_entry function.
Entry in sparse port table is correct when the idx is 0. For idx 1 one
correct entry should be skipped, for idx 2 two of them should be skipped
etc. Change if condition to be true when idx is 0, which means that
previous valid entry of this tunnel type were skipped.
Fixes: b20e6c17c4 ("ice: convert to new udp_tunnel infrastructure")
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b9b546dc0 ]
There is a noise issue for 8kHz sample rate on slave mode.
Compared with master mode, the difference is the DACDIV
setting, after correcting the DACDIV, the noise is gone.
There is no noise issue for 48kHz sample rate, because
the default value of DACDIV is correct for 48kHz.
So wm8960_configure_clocking() should be functional for
ADC and DAC function even if it is slave mode.
In order to be compatible for old use case, just add
condition for checking that sysclk is zero with
slave mode.
Fixes: 0e50b51aa2 ("ASoC: wm8960: Let wm8960 driver configure its bit clock and frame clock")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/1634102224-3922-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 293d92cbbd ]
The following warning occurred sporadically on s390:
DMA-API: nvme 0006:00:00.0: device driver maps memory from kernel text or rodata [addr=0000000048cc5e2f] [len=131072]
WARNING: CPU: 4 PID: 825 at kernel/dma/debug.c:1083 check_for_illegal_area+0xa8/0x138
It is a false-positive warning, due to broken logic in debug_dma_map_sg().
check_for_illegal_area() checks for overlay of sg elements with kernel text
or rodata. It is called with sg_dma_len(s) instead of s->length as
parameter. After the call to ->map_sg(), sg_dma_len() will contain the
length of possibly combined sg elements in the DMA address space, and not
the individual sg element length, which would be s->length.
The check will then use the physical start address of an sg element, and
add the DMA length for the overlap check, which could result in the false
warning, because the DMA length can be larger than the actual single sg
element length.
In addition, the call to check_for_illegal_area() happens in the iteration
over mapped_ents, which will not include all individual sg elements if
any of them were combined in ->map_sg().
Fix this by using s->length instead of sg_dma_len(s). Also put the call to
check_for_illegal_area() in a separate loop, iterating over all the
individual sg elements ("nents" instead of "mapped_ents").
While at it, as suggested by Robin Murphy, also move check_for_stack()
inside the new loop, as it is similarly concerned with validating the
individual sg elements.
Link: https://lore.kernel.org/lkml/20210705185252.4074653-1-gerald.schaefer@linux.ibm.com
Fixes: 884d05970b ("dma-debug: use sg_dma_len accessor")
Signed-off-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c20106944e ]
If nfsd has existing listening sockets without any processes, then an error
returned from svc_create_xprt() for an additional transport will remove
those existing listeners. We're seeing this in practice when userspace
attempts to create rpcrdma transports without having the rpcrdma modules
present before creating nfsd kernel processes. Fix this by checking for
existing sockets before calling nfsd_destroy().
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 012e974501 ]
Rebooting xtensa images loaded with the '-kernel' option in qemu does
not work. When executing a reboot command, the qemu session either hangs
or experiences an endless sequence of error messages.
Kernel panic - not syncing: Unrecoverable error in exception handler
Reset code jumps to the CPU restart address, but Linux can not recover
from there because code and data in the kernel init sections have been
discarded and overwritten at this point.
XTFPGA platforms have a means to reset the CPU by writing 0xdead into a
specific FPGA IO address. When used in QEMU the kernel image loaded with
the '-kernel' option gets restored to its original state allowing the
machine to boot successfully.
Use that mechanism to attempt a platform reset. If it does not work,
fall back to the existing mechanism.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3d7c2cdf6 ]
Use platform data to initialize xtfpga device drivers when CONFIG_USE_OF
is not selected. This fixes xtfpga networking when CONFIG_USE_OF is not
selected but CONFIG_OF is.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9172b5c4a7 ]
Like xen_start_flags, xen_domain_type gets set before .bss gets cleared.
Hence this variable also needs to be prevented from getting put in .bss,
which is possible because XEN_NATIVE is an enumerator evaluating to
zero. Any use prior to init_hvm_pv_info() setting the variable again
would lead to wrong decisions; one such case is xenboot_console_setup()
when called as a result of "earlyprintk=xen".
Use __ro_after_init as more applicable than either __section(".data") or
__read_mostly.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/d301677b-6f22-5ae6-bd36-458e1f323d0b@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
The linux-5.10.y backport of commit "io_uring: add ->splice_fd_in checks"
includes a typo: "|" where "||" should be. (The original upstream commit
is fine.)
Fixes: 54eb6211b9 ("io_uring: add ->splice_fd_in checks")
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org # v5.10
Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f1fce595b upstream.
Fix lots of fallthrough warnings, e.g.:
arch/parisc/math-emu/fpudispatch.c:323:33: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both the firmware audio driver and the vc4-kms-v3d driver are capable
of providing HDMI audio, but only one should be active at any time.
The vc4-kms-v3d overlays disable the firmware audio driver, but they
also have a noaudio parameter that as well as disabling the ARM-side
HDMI audio also re-enables the firmware HDMI audio. This is not
guaranteed to work and has been seen to break the display completely.
Modify the noaudio parameters so that the firmware HDMI audio support
remains disabled.
See: https://github.com/raspberrypi/linux/issues/4651
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Limit the number of allowed video callbacks. This helps with limiting
the size of the coded input FIFO which in turn helps to control latency.
Choose -5 as the magic number as it translates to DPB+5 buffers which
has been proven to be a good number in the past.
Ideally coded buffers would not be returned to the user until they
had been decoded into the DPB or been discarded as bad, but that grade
of control is unavailable to us.
Signed-off-by: John Cox <jc@kynesim.co.uk>
Commit db8e94e7cf upstream
The existing link format validation failure debug message in media-entity.c
helped to pinpoint the point of failure but provided no additional
information what's wrong. Tell the user exactly why the validation failed.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Adds Media Controller API support for more complex pipelines.
libcamera is about to switch to using this mechanism for configuring
sensors.
This can be enabled by either a module parameter, or device tree.
Various functions have been moved to group video-centric and
mc-centric functions together.
Based on a similar conversion done to ti-vpe.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The driver was making big assumptions about the source device
using pad 0 and 1, which doesn't follow for more complex
devices where Unicam's source device may be a sink device for
something else.
Read the pad numbers through media controller, and reference
them appropriately.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
RAW color spaces are more usually reported as having full range
quantization.
Tested using libcamera.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
commit 4a3e0aeddf upstream.
mv88e6xxx_port_ppu_updates() interpretes data in the PORT_STS
register incorrectly for internal ports (ie no PPU). In these
cases, the PHY_DETECT bit indicates link status. This results
in forcing the MAC state whenever the PHY link goes down which
is not intended. As a side effect, LED's configured to show
link status stay lit even though the physical link is down.
Add a check in mac_link_down and mac_link_up to see if it
concerns an external port and only then, look at PPU status.
Fixes: 5d5b231da7 (net: dsa: mv88e6xxx: use PHY_DETECT in mac_link_up/mac_link_down)
Reported-by: Maarten Zanders <m.zanders@televic.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Maarten Zanders <maarten.zanders@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c976a5657 upstream.
Bridging, and possibly other upper stack gizmos, adds the
lower device's netdev->dev_addr to its own uc list, and
then requests it be deleted when the upper bridge device is
removed. This delete request also happens with the bridging
vlan_filtering is enabled and then disabled.
Bonding has a similar behavior with the uc list, but since it
also uses set_mac to manage netdev->dev_addr, it doesn't have
the same the failure case.
Because we store our netdev->dev_addr in our uc list, we need
to ignore the delete request from dev_uc_sync so as to not
lose the address and all hope of communicating. Note that
ndo_set_mac_address is expressly changing netdev->dev_addr,
so no limitation is set there.
Fixes: 2a654540be ("ionic: Add Rx filter and rx_mode ndo support")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9fde506e0c upstream.
When skb_match is NULL, it means we received a PTP IRQ for a timestamp
ID that the kernel has no idea about, since there is no skb in the
timestamping queue with that timestamp ID.
This is a grave error and not something to just "continue" over.
So print a big warning in case this happens.
Also, move the check above ocelot_get_hwtimestamp(), there is no point
in reading the full 64-bit current PTP time if we're not going to do
anything with it anyway for this skb.
Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9973a43012 upstream.
Fix the following build/link errors by adding a dependency on
CRYPTO, CRYPTO_HASH, CRYPTO_SHA256 and CRC32:
ld: drivers/net/usb/r8152.o: in function `rtl8152_fw_verify_checksum':
r8152.c:(.text+0x2b2a): undefined reference to `crypto_alloc_shash'
ld: r8152.c:(.text+0x2bed): undefined reference to `crypto_shash_digest'
ld: r8152.c:(.text+0x2c50): undefined reference to `crypto_destroy_tfm'
ld: drivers/net/usb/r8152.o: in function `_rtl8152_set_rx_mode':
r8152.c:(.text+0xdcb0): undefined reference to `crc32_le'
Fixes: 9370f2d05a ("r8152: support request_firmware for RTL8153")
Fixes: ac718b6930 ("net/usb: new driver for RTL8152")
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5a14ea7b4 upstream.
The error code is missing in this code scenario, add the error code
'-EINVAL' to the return value 'rc'.
Eliminate the follow smatch warning:
drivers/net/ethernet/qlogic/qed/qed_main.c:1298 qed_slowpath_start()
warn: missing error code 'rc'.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Fixes: d51e4af5c2 ("qed: aRFS infrastructure support")
Signed-off-by: chongjiapeng <jiapeng.chong@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1413269086 upstream.
Introduction of lockless subqueues broke the class statistics.
Before the change stats were accumulated in `bstats' and `qstats'
on the stack which was then copied to struct gnet_dump.
After the change the `bstats' and `qstats' are initialized to 0
and never updated, yet still fed to gnet_dump. The code updates
the global qdisc->cpu_bstats and qdisc->cpu_qstats instead,
clobbering them. Most likely a copy-paste error from the code in
mqprio_dump().
__gnet_stats_copy_basic() and __gnet_stats_copy_queue() accumulate
the values for per-CPU case but for global stats they overwrite
the value, so only stats from the last loop iteration / tc end up
in sch->[bq]stats.
Use the on-stack [bq]stats variables again and add the stats manually
in the global case.
Fixes: ce679e8df7 ("net: sched: add support for TCQ_F_NOLOCK subqueues to sch_mqprio")
Cc: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
https://lore.kernel.org/all/20211007175000.2334713-2-bigeasy@linutronix.de/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 596143e3ae upstream.
Fix modpost Section mismatch error in next_platform_timer().
[...]
WARNING: modpost: vmlinux.o(.text.unlikely+0x26e60): Section mismatch in reference from the function next_platform_timer() to the variable .init.data:acpi_gtdt_desc
The function next_platform_timer() references
the variable __initdata acpi_gtdt_desc.
This is often because next_platform_timer lacks a __initdata
annotation or the annotation of acpi_gtdt_desc is wrong.
WARNING: modpost: vmlinux.o(.text.unlikely+0x26e64): Section mismatch in reference from the function next_platform_timer() to the variable .init.data:acpi_gtdt_desc
The function next_platform_timer() references
the variable __initdata acpi_gtdt_desc.
This is often because next_platform_timer lacks a __initdata
annotation or the annotation of acpi_gtdt_desc is wrong.
ERROR: modpost: Section mismatches detected.
Set CONFIG_SECTION_MISMATCH_WARN_ONLY=y to allow them.
make[1]: *** [scripts/Makefile.modpost:59: vmlinux.symvers] Error 1
make[1]: *** Deleting file 'vmlinux.symvers'
make: *** [Makefile:1176: vmlinux] Error 2
[...]
Fixes: a712c3ed9b ("acpi/arm64: Add memory-mapped timer support in GTDT driver")
Signed-off-by: Jackie Liu <liuyun01@kylinos.cn>
Acked-by: Hanjun Guo <guohanjun@huawei.com>
Link: https://lore.kernel.org/r/20210823092526.2407526-1-liu.yun@linux.dev
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14eb0cb4e9 upstream.
In theory a context can be destroyed and a new one allocated at the same
address, making the pointer comparision to detect when we don't need to
update the current pagetables invalid. Instead assign a sequence number
to each context on creation, and use this for the check.
Fixes: 84c31ee16f ("drm/msm/a6xx: Add support for per-instance pagetables")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97794170b6 upstream.
In commit e11f5bd822 ("drm: Add support for DP 1.4 Compliance edid
corruption test") the function connector_bad_edid() started assuming
that the memory for the EDID passed to it was big enough to hold
`edid[0x7e] + 1` blocks of data (1 extra for the base block). It
completely ignored the fact that the function was passed `num_blocks`
which indicated how much memory had been allocated for the EDID.
Let's fix this by adding a bounds check.
This is important for handling the case where there's an error in the
first block of the EDID. In that case we will call
connector_bad_edid() without having re-allocated memory based on
`edid[0x7e]`.
Fixes: e11f5bd822 ("drm: Add support for DP 1.4 Compliance edid corruption test")
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211005192905.v2.1.Ib059f9c23c2611cb5a9d760e7d0a700c1295928d@changeid
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 75b3cb97eb upstream.
Intermittent Kernel crash has been observed on probe in
bcm_qspi_mspi_l2_isr() handler when the MSPI spifie interrupt bit
has not been cleared before registering for interrupts.
Fix the driver to move SoC specific custom interrupt handling code
before we register IRQ in probe. Also clear MSPI interrupt status
resgiter prior to registering IRQ handlers.
Fixes: cc20a38612 ("spi: iproc-qspi: Add Broadcom iProc SoCs support")
Signed-off-by: Kamal Dasu <kdasu@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211008203603.40915-3-kdasu.kdev@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b02420169 upstream.
Change kstrtou32() argument 'base' to be zero instead of 'len'.
It works by chance for setting one bit value, but it is not supposed to
work in case value passed to mlxreg_io_attr_store() is greater than 1.
It works for example, for:
echo 1 > /sys/devices/platform/mlxplat/mlxreg-io/hwmon/.../jtag_enable
But it will fail for:
echo n > /sys/devices/platform/mlxplat/mlxreg-io/hwmon/.../jtag_enable,
where n > 1.
The flow for input buffer conversion is as below:
_kstrtoull(const char *s, unsigned int base, unsigned long long *res)
calls:
rv = _parse_integer(s, base, &_res);
For the second case, where n > 1:
- _parse_integer() converts 's' to 'val'.
For n=2, 'len' is set to 2 (string buffer is 0x32 0x0a), for n=3
'len' is set to 3 (string buffer 0x33 0x0a), etcetera.
- 'base' is equal or greater then '2' (length of input buffer).
As a result, _parse_integer() exits with result zero (rv):
rv = 0;
while (1) {
...
if (val >= base)-> (2 >= 2)
break;
...
rv++;
...
}
And _kstrtoull() in their turn will fail:
if (rv == 0)
return -EINVAL;
Fixes: 5ec4a8ace0 ("platform/mellanox: Introduce support for Mellanox register access driver")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20210927142214.2613929-2-vadimp@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 332fdf951d upstream.
Currently, mlxsw allows cooling states to be set above the maximum
cooling state supported by the driver:
# cat /sys/class/thermal/thermal_zone2/cdev0/type
mlxsw_fan
# cat /sys/class/thermal/thermal_zone2/cdev0/max_state
10
# echo 18 > /sys/class/thermal/thermal_zone2/cdev0/cur_state
# echo $?
0
This results in out-of-bounds memory accesses when thermal state
transition statistics are enabled (CONFIG_THERMAL_STATISTICS=y), as the
transition table is accessed with a too large index (state) [1].
According to the thermal maintainer, it is the responsibility of the
driver to reject such operations [2].
Therefore, return an error when the state to be set exceeds the maximum
cooling state supported by the driver.
To avoid dead code, as suggested by the thermal maintainer [3],
partially revert commit a421ce088a ("mlxsw: core: Extend cooling
device with cooling levels") that tried to interpret these invalid
cooling states (above the maximum) in a special way. The cooling levels
array is not removed in order to prevent the fans going below 20% PWM,
which would cause them to get stuck at 0% PWM.
[1]
BUG: KASAN: slab-out-of-bounds in thermal_cooling_device_stats_update+0x271/0x290
Read of size 4 at addr ffff8881052f7bf8 by task kworker/0:0/5
CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted 5.15.0-rc3-custom-45935-gce1adf704b14 #122
Hardware name: Mellanox Technologies Ltd. "MSN2410-CB2FO"/"SA000874", BIOS 4.6.5 03/08/2016
Workqueue: events_freezable_power_ thermal_zone_device_check
Call Trace:
dump_stack_lvl+0x8b/0xb3
print_address_description.constprop.0+0x1f/0x140
kasan_report.cold+0x7f/0x11b
thermal_cooling_device_stats_update+0x271/0x290
__thermal_cdev_update+0x15e/0x4e0
thermal_cdev_update+0x9f/0xe0
step_wise_throttle+0x770/0xee0
thermal_zone_device_update+0x3f6/0xdf0
process_one_work+0xa42/0x1770
worker_thread+0x62f/0x13e0
kthread+0x3ee/0x4e0
ret_from_fork+0x1f/0x30
Allocated by task 1:
kasan_save_stack+0x1b/0x40
__kasan_kmalloc+0x7c/0x90
thermal_cooling_device_setup_sysfs+0x153/0x2c0
__thermal_cooling_device_register.part.0+0x25b/0x9c0
thermal_cooling_device_register+0xb3/0x100
mlxsw_thermal_init+0x5c5/0x7e0
__mlxsw_core_bus_device_register+0xcb3/0x19c0
mlxsw_core_bus_device_register+0x56/0xb0
mlxsw_pci_probe+0x54f/0x710
local_pci_probe+0xc6/0x170
pci_device_probe+0x2b2/0x4d0
really_probe+0x293/0xd10
__driver_probe_device+0x2af/0x440
driver_probe_device+0x51/0x1e0
__driver_attach+0x21b/0x530
bus_for_each_dev+0x14c/0x1d0
bus_add_driver+0x3ac/0x650
driver_register+0x241/0x3d0
mlxsw_sp_module_init+0xa2/0x174
do_one_initcall+0xee/0x5f0
kernel_init_freeable+0x45a/0x4de
kernel_init+0x1f/0x210
ret_from_fork+0x1f/0x30
The buggy address belongs to the object at ffff8881052f7800
which belongs to the cache kmalloc-1k of size 1024
The buggy address is located 1016 bytes inside of
1024-byte region [ffff8881052f7800, ffff8881052f7c00)
The buggy address belongs to the page:
page:0000000052355272 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x1052f0
head:0000000052355272 order:3 compound_mapcount:0 compound_pincount:0
flags: 0x200000000010200(slab|head|node=0|zone=2)
raw: 0200000000010200 ffffea0005034800 0000000300000003 ffff888100041dc0
raw: 0000000000000000 0000000000100010 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8881052f7a80: 00 00 00 00 00 00 04 fc fc fc fc fc fc fc fc fc
ffff8881052f7b00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff8881052f7b80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^
ffff8881052f7c00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff8881052f7c80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[2] https://lore.kernel.org/linux-pm/9aca37cb-1629-5c67-1895-1fdc45c0244e@linaro.org/
[3] https://lore.kernel.org/linux-pm/af9857f2-578e-de3a-e62b-6baff7e69fd4@linaro.org/
CC: Daniel Lezcano <daniel.lezcano@linaro.org>
Fixes: a50c1e3565 ("mlxsw: core: Implement thermal zone")
Fixes: a421ce088a ("mlxsw: core: Extend cooling device with cooling levels")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20211012174955.472928-1-idosch@idosch.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 776c750108 upstream.
I got a null-ptr-deref report:
KASAN: null-ptr-deref in range [0x0000000000000090-0x0000000000000097]
...
RIP: 0010:regulator_enable+0x84/0x260
...
Call Trace:
ahci_platform_enable_regulators+0xae/0x320
ahci_platform_enable_resources+0x1a/0x120
ahci_probe+0x4f/0x1b9
platform_probe+0x10b/0x280
...
entry_SYSCALL_64_after_hwframe+0x44/0xae
If devm_regulator_get() in ahci_platform_get_resources() fails,
hpriv->phy_regulator will point to NULL, when enabling or disabling it,
null-ptr-deref will occur.
ahci_probe()
ahci_platform_get_resources()
devm_regulator_get(, "phy") // failed, let phy_regulator = NULL
ahci_platform_enable_resources()
ahci_platform_enable_regulators()
regulator_enable(hpriv->phy_regulator) // null-ptr-deref
commit 962399bb7f ("ata: libahci_platform: Fix regulator_get_optional()
misuse") replaces devm_regulator_get_optional() with devm_regulator_get(),
but PHY regulator omits to delete "hpriv->phy_regulator = NULL;" like AHCI.
Delete it like AHCI regulator to fix this bug.
Fixes: commit 962399bb7f ("ata: libahci_platform: Fix regulator_get_optional() misuse")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 291c932fc3 upstream.
'skb' is allocated in digital_in_send_sdd_req(), but not free when
digital_in_send_cmd() failed, which will cause memory leak. Fix it
by freeing 'skb' if digital_in_send_cmd() return failed.
Fixes: 2c66daecc4 ("NFC Digital: Add NFC-A technology support")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58e7dcc9ca upstream.
'params' is allocated in digital_tg_listen_mdaa(), but not free when
digital_send_cmd() failed, which will cause memory leak. Fix it by
freeing 'params' if digital_send_cmd() return failed.
Fixes: 1c7a4c24fb ("NFC Digital: Add target NFC-DEP support")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40507e7aad upstream.
After recent cleanups, gcc started warning about a suspicious
memcpy() call during the s2io_io_resume() function:
In function '__dev_addr_set',
inlined from 'eth_hw_addr_set' at include/linux/etherdevice.h:318:2,
inlined from 's2io_set_mac_addr' at drivers/net/ethernet/neterion/s2io.c:5205:2,
inlined from 's2io_io_resume' at drivers/net/ethernet/neterion/s2io.c:8569:7:
arch/x86/include/asm/string_32.h:182:25: error: '__builtin_memcpy' accessing 6 bytes at offsets 0 and 2 overlaps 4 bytes at offset 2 [-Werror=restrict]
182 | #define memcpy(t, f, n) __builtin_memcpy(t, f, n)
| ^~~~~~~~~~~~~~~~~~~~~~~~~
include/linux/netdevice.h:4648:9: note: in expansion of macro 'memcpy'
4648 | memcpy(dev->dev_addr, addr, len);
| ^~~~~~
What apparently happened is that an old cleanup changed the calling
conventions for s2io_set_mac_addr() from taking an ethernet address
as a character array to taking a struct sockaddr, but one of the
callers was not changed at the same time.
Change it to instead call the low-level do_s2io_prog_unicast() function
that still takes the old argument type.
Fixes: 2fd3768845 ("S2io: Added support set_mac_address driver entry point")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211013143613.2049096-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef1100ef20 upstream.
When the ksz module is installed and removed using rmmod, kernel crashes
with null pointer dereferrence error. During rmmod, ksz_switch_remove
function tries to cancel the mib_read_workqueue using
cancel_delayed_work_sync routine and unregister switch from dsa.
During dsa_unregister_switch it calls ksz_mac_link_down, which in turn
reschedules the workqueue since mib_interval is non-zero.
Due to which queue executed after mib_interval and it tries to access
dp->slave. But the slave is unregistered in the ksz_switch_remove
function. Hence kernel crashes.
To avoid this crash, before canceling the workqueue, resetted the
mib_interval to 0.
v1 -> v2:
-Removed the if condition in ksz_mib_read_work
Fixes: 469b390e1b ("net: dsa: microchip: use delayed_work instead of timer + work")
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 075da584ba upstream.
Some old IPs do not provide the hardware feature register.
On these IPs, this register is read 0x00000000.
In old driver version, this feature was handled but a regression came
with the commit f10a6a3541 ("stmmac: rework get_hw_feature function").
Indeed, this commit removes the return value in dma->get_hw_feature().
This return value was used to indicate the validity of retrieved
information and used later on in stmmac_hw_init() to override
priv->plat data if this hardware feature were valid.
This patch restores the return code in ->get_hw_feature() in order
to indicate the hardware feature validity and override priv->plat
data only if this hardware feature is valid.
Fixes: f10a6a3541 ("stmmac: rework get_hw_feature function")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0bc73ad46a upstream.
Due to current HW arch limitations, RX-FCS (scattering FCS frame field
to software) and RX-port-timestamp (improved timestamp accuracy on the
receive side) can't work together.
RX-port-timestamp is not controlled by the user and it is enabled by
default when supported by the HW/FW.
This patch sets RX-port-timestamp opposite to RX-FCS configuration.
Fixes: 102722fc68 ("net/mlx5e: Add support for RXFCS feature flag")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e599ee234a upstream.
Fix the following build/link error by adding a dependency on the CRC32
routines:
ld: drivers/net/ethernet/arc/emac_main.o: in function `arc_emac_set_rx_mode':
emac_main.c:(.text+0xb11): undefined reference to `crc32_le'
The crc32_le() call comes through the ether_crc_le() call in
arc_emac_set_rx_mode().
[v2: moved the select to ARC_EMAC_CORE; the Makefile is a bit confusing,
but the error comes from emac_main.o, which is part of the arc_emac module,
which in turn is enabled by CONFIG_ARC_EMAC_CORE. Note that arc_emac is
different from emac_arc...]
Fixes: 775dd682e2 ("arc_emac: implement promiscuous mode and multicast filtering")
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Link: https://lore.kernel.org/r/20211012093446.1575-1-vegard.nossum@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 55a9968c7e upstream.
The commit 15add06841 ("gpio: pca953x: add ->set_config implementation")
introduced support for bias setting. However this, due to being half-baked,
brought potential issues:
- the turning bias via disabling makes the pin floating for a while;
- once enabled, bias can't be disabled.
Fix all these by adding support for bias disabling and move the disabling
part under the corresponding conditional.
While at it, add support for default setting, since it's cheap to add.
Fixes: 15add06841 ("gpio: pca953x: add ->set_config implementation")
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85f74acf09 upstream.
The request tag is no longer the only component of the command id.
Fixes: e7006de6c2 ("nvme: code command_id with a genctr for use-after-free validation")
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13dbc954b3 upstream.
dtbs_check currently complains that:
arch/arm/boot/dts/bcm2711-rpi-4-b.dts:220.10-231.4: Warning
(pci_device_reg): /scb/pcie@7d500000/pci@1,0: PCI unit address format
error, expected "0,0"
Unsurprisingly pci@0,0 is the right address, as illustrated by its reg
property:
&pcie0 {
pci@0,0 {
/*
* As defined in the IEEE Std 1275-1994 document,
* reg is a five-cell address encoded as (phys.hi
* phys.mid phys.lo size.hi size.lo). phys.hi
* should contain the device's BDF as 0b00000000
* bbbbbbbb dddddfff 00000000. The other cells
* should be zero.
*/
reg = <0 0 0 0 0>;
};
};
The device is clearly 0. So fix it.
Also add a missing 'device_type = "pci"'.
Fixes: 258f92d2f8 ("ARM: dts: bcm2711: Add reset controller to xHCI node")
Suggested-by: Rob Herring <robh@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210831125843.1233488-1-nsaenzju@redhat.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f565d0ead upstream.
When OP-TEE driver is built as a module, OP-TEE client devices
registered on TEE bus during probe should be unregistered during
optee_remove. So implement optee_unregister_devices() accordingly.
Fixes: c3fa24af92 ("tee: optee: add TEE bus device enumeration support")
Reported-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a913270e5 upstream.
In Sigma-Delta devices the SDO line is also used as an interrupt.
Leaving IRQ on level instead of falling might trigger a sample read
when the IRQ is enabled, as the SDO line is already low. Not sure
if SDO line will always immediately go high in ad_sd_buffer_postenable
before the IRQ is enabled.
Also the datasheet seem to explicitly say the falling edge of the SDO
should be used as an interrupt:
>From the AD7793 datasheet: " The DOUT/RDY falling edge can be
used as an interrupt to a processor"
Fixes: da4d3d6bb9 ("iio: adc: ad-sigma-delta: Allow custom IRQ flags")
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210906065630.16325-4-alexandru.tachici@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e081102f30 upstream.
Correct IRQ flag here is falling.
In Sigma-Delta devices the SDO line is also used as an interrupt.
Leaving IRQ on level instead of falling might trigger a sample read
when the IRQ is enabled, as the SDO line is already low. Not sure
if SDO line will always immediately go high in ad_sd_buffer_postenable
before the IRQ is enabled.
Also the datasheet seem to explicitly say the falling edge of the SDO
should be used as an interrupt:
>From the AD7780 datasheet: " The DOUT/Figure 22 RDY falling edge
can be used as an interrupt to a processor"
Fixes: da4d3d6bb9 ("iio: adc: ad-sigma-delta: Allow custom IRQ flags")
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210906065630.16325-3-alexandru.tachici@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89a86da5cb upstream.
IRQ type in ad_sigma_delta_info struct was missing.
In Sigma-Delta devices the SDO line is also used as an interrupt.
Leaving IRQ on level instead of falling might trigger a sample read
when the IRQ is enabled, as the SDO line is already low. Not sure
if SDO line will always immediately go high in ad_sd_buffer_postenable
before the IRQ is enabled.
Also the datasheet seem to explicitly say the falling edge of the SDO
should be used as an interrupt:
>From the AD7192 datasheet: "The DOUT/RDY falling edge can be used
as an interrupt to a processor,"
Fixes: da4d3d6bb9 ("iio: adc: ad-sigma-delta: Allow custom IRQ flags")
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210906065630.16325-2-alexandru.tachici@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f729a592ad upstream.
SYNC_STATE_ONLY device links intentionally allow cycles because cyclic
sync_state() dependencies are valid and necessary.
However a SYNC_STATE_ONLY device link where the consumer and the supplier
are the same device is pointless because the device link would be deleted
as soon as the device probes (because it's also the consumer) and won't
affect when the sync_state() callback is called. It's a waste of CPU cycles
and memory to create this device link. So reject any attempts to create
such a device link.
Fixes: 05ef983e0d ("driver core: Add device link support for SYNC_STATE_ONLY flag")
Cc: stable <stable@vger.kernel.org>
Reported-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20210929190549.860541-1-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f779e1d35 upstream.
When an interrupt is passed through, the KVM XIVE device calls the
set_vcpu_affinity() handler which raises the P bit to mask the
interrupt and to catch any in-flight interrupts while routing the
interrupt to the guest.
On the guest side, drivers (like some Intels) can request at probe
time some MSIs and call synchronize_irq() to check that there are no
in flight interrupts. This will call the XIVE get_irqchip_state()
handler which will always return true as the interrupt P bit has been
set on the host side and lock the CPU in an infinite loop.
Fix that by discarding disabled interrupts in get_irqchip_state().
Fixes: da15c03b04 ("powerpc/xive: Implement get_irqchip_state method for XIVE to fix shutdown race")
Cc: stable@vger.kernel.org #v5.4+
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Tested-by: seeteena <s1seetee@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211011070203.99726-1-clg@kaod.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 711885906b upstream.
This Kconfig option was added initially so that memory encryption is
enabled by default on machines which support it.
However, devices which have DMA masks that are less than the bit
position of the encryption bit, aka C-bit, require the use of an IOMMU
or the use of SWIOTLB.
If the IOMMU is disabled or in passthrough mode, the kernel would switch
to SWIOTLB bounce-buffering for those transfers.
In order to avoid that,
2cc13bb4f5 ("iommu: Disable passthrough mode when SME is active")
disables the default IOMMU passthrough mode so that devices for which the
default 256K DMA is insufficient, can use the IOMMU instead.
However 2, there are cases where the IOMMU is disabled in the BIOS, etc.
(think the usual hardware folk "oops, I dropped the ball there" cases) or a
driver doesn't properly use the DMA APIs or a device has a firmware or
hardware bug, e.g.:
ea68573d40 ("drm/amdgpu: Fail to load on RAVEN if SME is active")
However 3, in the above GPU use case, there are APIs like Vulkan and
some OpenGL/OpenCL extensions which are under the assumption that
user-allocated memory can be passed in to the kernel driver and both the
GPU and CPU can do coherent and concurrent access to the same memory.
That cannot work with SWIOTLB bounce buffers, of course.
So, in order for those devices to function, drop the "default y" for the
SME by default active option so that users who want to have SME enabled,
will need to either enable it in their config or use "mem_encrypt=on" on
the kernel command line.
[ tlendacky: Generalize commit message. ]
Fixes: 7744ccdbc1 ("x86/mm: Add Secure Memory Encryption (SME) support")
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/8bbacd0e-4580-3194-19d2-a0ecad7df09c@molgen.mpg.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d388fa01f upstream.
If a cell has 'nbits' equal to a multiple of BITS_PER_BYTE the logic
*p &= GENMASK((cell->nbits%BITS_PER_BYTE) - 1, 0);
will become undefined behavior because nbits modulo BITS_PER_BYTE is 0, and we
subtract one from that making a large number that is then shifted more than the
number of bits that fit into an unsigned long.
UBSAN reports this problem:
UBSAN: shift-out-of-bounds in drivers/nvmem/core.c:1386:8
shift exponent 64 is too large for 64-bit type 'unsigned long'
CPU: 6 PID: 7 Comm: kworker/u16:0 Not tainted 5.15.0-rc3+ #9
Hardware name: Google Lazor (rev3+) with KB Backlight (DT)
Workqueue: events_unbound deferred_probe_work_func
Call trace:
dump_backtrace+0x0/0x170
show_stack+0x24/0x30
dump_stack_lvl+0x64/0x7c
dump_stack+0x18/0x38
ubsan_epilogue+0x10/0x54
__ubsan_handle_shift_out_of_bounds+0x180/0x194
__nvmem_cell_read+0x1ec/0x21c
nvmem_cell_read+0x58/0x94
nvmem_cell_read_variable_common+0x4c/0xb0
nvmem_cell_read_variable_le_u32+0x40/0x100
a6xx_gpu_init+0x170/0x2f4
adreno_bind+0x174/0x284
component_bind_all+0xf0/0x264
msm_drm_bind+0x1d8/0x7a0
try_to_bring_up_master+0x164/0x1ac
__component_add+0xbc/0x13c
component_add+0x20/0x2c
dp_display_probe+0x340/0x384
platform_probe+0xc0/0x100
really_probe+0x110/0x304
__driver_probe_device+0xb8/0x120
driver_probe_device+0x4c/0xfc
__device_attach_driver+0xb0/0x128
bus_for_each_drv+0x90/0xdc
__device_attach+0xc8/0x174
device_initial_probe+0x20/0x2c
bus_probe_device+0x40/0xa4
deferred_probe_work_func+0x7c/0xb8
process_one_work+0x128/0x21c
process_scheduled_works+0x40/0x54
worker_thread+0x1ec/0x2a8
kthread+0x138/0x158
ret_from_fork+0x10/0x20
Fix it by making sure there are any bits to mask out.
Fixes: 69aba7948c ("nvmem: Add a simple NVMEM framework for consumers")
Cc: Douglas Anderson <dianders@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20211013124511.18726-1-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9b7748ffc upstream.
The number of correctable errors is displayed as uncorrectable
errors because the "SBE" error count is passed to both calls of
edac_mc_handle_error().
Pass the correct uncorrectable error count to the second
edac_mc_handle_error() call when logging uncorrectable errors.
[ bp: Massage commit message. ]
Fixes: 7f6998a412 ("ARM: 8888/1: EDAC: Add driver for the Marvell Armada XP SDRAM and L2 cache ECC")
Signed-off-by: Hans Potsch <hans.potsch@nokia.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20211006121332.58788-1-hans.potsch@nokia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f9a174f91 upstream.
The virtio specification virtio-v1.1-cs01 states: "Transitional devices
MUST detect Legacy drivers by detecting that VIRTIO_F_VERSION_1 has not
been acknowledged by the driver." This is exactly what QEMU as of 6.1
has done relying solely on VIRTIO_F_VERSION_1 for detecting that.
However, the specification also says: "... the driver MAY read (but MUST
NOT write) the device-specific configuration fields to check that it can
support the device ..." before setting FEATURES_OK.
In that case, any transitional device relying solely on
VIRTIO_F_VERSION_1 for detecting legacy drivers will return data in
legacy format. In particular, this implies that it is in big endian
format for big endian guests. This naturally confuses the driver which
expects little endian in the modern mode.
It is probably a good idea to amend the spec to clarify that
VIRTIO_F_VERSION_1 can only be relied on after the feature negotiation
is complete. Before validate callback existed, config space was only
read after FEATURES_OK. However, we already have two regressions, so
let's address this here as well.
The regressions affect the VIRTIO_NET_F_MTU feature of virtio-net and
the VIRTIO_BLK_F_BLK_SIZE feature of virtio-blk for BE guests when
virtio 1.0 is used on both sides. The latter renders virtio-blk unusable
with DASD backing, because things simply don't work with the default.
See Fixes tags for relevant commits.
For QEMU, we can work around the issue by writing out the feature bits
with VIRTIO_F_VERSION_1 bit set. We (ab)use the finalize_features
config op for this. This isn't enough to address all vhost devices since
these do not get the features until FEATURES_OK, however it looks like
the affected devices actually never handled the endianness for legacy
mode correctly, so at least that's not a regression.
No devices except virtio net and virtio blk seem to be affected.
Long term the right thing to do is to fix the hypervisors.
Cc: <stable@vger.kernel.org> #v4.11
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Fixes: 82e89ea077 ("virtio-blk: Add validation for block size in config space")
Fixes: fe36cbe067 ("virtio_net: clear MTU when out of range")
Reported-by: markver@us.ibm.com
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Link: https://lore.kernel.org/r/20211011053921.1198936-1-pasic@linux.ibm.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9a470db27 upstream.
fastrpc driver is using find_vma() without any protection, as a
result we see below warning due to recent patch 5b78ed24e8
("mm/pagemap: add mmap_assert_locked() annotations to find_vma*()")
which added mmap_assert_locked() in find_vma() function.
This bug went un-noticed in previous versions. Fix this issue by adding
required protection while calling find_vma().
CPU: 0 PID: 209746 Comm: benchmark_model Not tainted 5.15.0-rc2-00445-ge14fe2bf817a-dirty #969
Hardware name: Qualcomm Technologies, Inc. Robotics RB5 (DT)
pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : find_vma+0x64/0xd0
lr : find_vma+0x60/0xd0
sp : ffff8000158ebc40
...
Call trace:
find_vma+0x64/0xd0
fastrpc_internal_invoke+0x570/0xda8
fastrpc_device_ioctl+0x3e0/0x928
__arm64_sys_ioctl+0xac/0xf0
invoke_syscall+0x44/0x100
el0_svc_common.constprop.3+0x70/0xf8
do_el0_svc+0x24/0x88
el0_svc+0x3c/0x138
el0t_64_sync_handler+0x90/0xb8
el0t_64_sync+0x180/0x184
Fixes: 80f3afd72b ("misc: fastrpc: consider address offset before sending to DSP")
Cc: stable@vger.kernel.org
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210922154326.8927-1-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2115b2b16 upstream.
Commit 7c75bde329 ("usb: musb: musb_dsps: request_irq() after
initializing musb") has inverted the calls to
dsps_setup_optional_vbus_irq() and dsps_create_musb_pdev() without
updating correctly the error path. dsps_create_musb_pdev() allocates and
registers a new platform device which must be unregistered and freed
with platform_device_unregister(), and this is missing upon
dsps_setup_optional_vbus_irq() error.
While on the master branch it seems not to trigger any issue, I observed
a kernel crash because of a NULL pointer dereference with a v5.10.70
stable kernel where the patch mentioned above was backported. With this
kernel version, -EPROBE_DEFER is returned the first time
dsps_setup_optional_vbus_irq() is called which triggers the probe to
error out without unregistering the platform device. Unfortunately, on
the Beagle Bone Black Wireless, the platform device still living in the
system is being used by the USB Ethernet gadget driver, which during the
boot phase triggers the crash.
My limited knowledge of the musb world prevents me to revert this commit
which was sent to silence a robot warning which, as far as I understand,
does not make sense. The goal of this patch was to prevent an IRQ to
fire before the platform device being registered. I think this cannot
ever happen due to the fact that enabling the interrupts is done by the
->enable() callback of the platform musb device, and this platform
device must be already registered in order for the core or any other
user to use this callback.
Hence, I decided to fix the error path, which might prevent future
errors on mainline kernels while also fixing older ones.
Fixes: 7c75bde329 ("usb: musb: musb_dsps: request_irq() after initializing musb")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20211005221631.1529448-1-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 38fa3206bf upstream.
While reboot the system by sysrq, the following bug will be occur.
BUG: sleeping function called from invalid context at kernel/locking/semaphore.c:90
in_atomic(): 0, irqs_disabled(): 128, non_block: 0, pid: 10052, name: rc.shutdown
CPU: 3 PID: 10052 Comm: rc.shutdown Tainted: G W O 5.10.0 #1
Call trace:
dump_backtrace+0x0/0x1c8
show_stack+0x18/0x28
dump_stack+0xd0/0x110
___might_sleep+0x14c/0x160
__might_sleep+0x74/0x88
down_interruptible+0x40/0x118
virt_efi_reset_system+0x3c/0xd0
efi_reboot+0xd4/0x11c
machine_restart+0x60/0x9c
emergency_restart+0x1c/0x2c
sysrq_handle_reboot+0x1c/0x2c
__handle_sysrq+0xd0/0x194
write_sysrq_trigger+0xbc/0xe4
proc_reg_write+0xd4/0xf0
vfs_write+0xa8/0x148
ksys_write+0x6c/0xd8
__arm64_sys_write+0x18/0x28
el0_svc_common.constprop.3+0xe4/0x16c
do_el0_svc+0x1c/0x2c
el0_svc+0x20/0x30
el0_sync_handler+0x80/0x17c
el0_sync+0x158/0x180
The reason for this problem is that irq has been disabled in
machine_restart() and then it calls down_interruptible() in
virt_efi_reset_system(), which would occur sleep in irq context,
it is dangerous! Commit 99409b935c9a("locking/semaphore: Add
might_sleep() to down_*() family") add might_sleep() in
down_interruptible(), so the bug info is here. down_trylock()
can solve this problem, cause there is no might_sleep.
--------
Cc: <stable@vger.kernel.org>
Signed-off-by: Zhang Jianhua <chris.zjh@huawei.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b3a72ca803 upstream.
Joe reports that using a statically allocated buffer for converting CPER
error records into human readable text is probably a bad idea. Even
though we are not aware of any actual issues, a stack buffer is clearly
a better choice here anyway, so let's move the buffer into the stack
frames of the two functions that refer to it.
Cc: <stable@vger.kernel.org>
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42641042c1 upstream.
clang-14 complains about an unusual way of converting a pointer to
an integer:
drivers/misc/cb710/sgbuf2.c:50:15: error: performing pointer subtraction with a null pointer has undefined behavior [-Werror,-Wnull-pointer-subtraction]
return ((ptr - NULL) & 3) != 0;
Replace this with a normal cast to uintptr_t.
Fixes: 5f5bac8272 ("mmc: Driver for CB710/720 memory card reader (MMC part)")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210927121408.939246-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff0e50d356 upstream.
The command ring pointer is located at [6:63] bits of the command
ring control register (CRCR). All the control bits like command stop,
abort are located at [0:3] bits. While aborting a command, we read the
CRCR and set the abort bit and write to the CRCR. The read will always
give command ring pointer as all zeros. So we essentially write only
the control bits. Since we split the 64 bit write into two 32 bit writes,
there is a possibility of xHC command ring stopped before the upper
dword (all zeros) is written. If that happens, xHC updates the upper
dword of its internal command ring pointer with all zeros. Next time,
when the command ring is restarted, we see xHC memory access failures.
Fix this issue by only writing to the lower dword of CRCR where all
control bits are located.
Cc: stable@vger.kernel.org
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211008092547.3996295-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4afb912f43 upstream.
Error injection testing uncovered a case where we'd end up with a
corrupt file system with a missing extent in the middle of a file. This
occurs because the if statement to decide if we should abort is wrong.
The only way we would abort in this case is if we got a ret !=
-EOPNOTSUPP and we called from the file clone code. However the
prealloc code uses this path too. Instead we need to abort if there is
an error, and the only error we _don't_ abort on is -EOPNOTSUPP and only
if we came from the clone file code.
CC: stable@vger.kernel.org # 5.10+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d175209be0 upstream.
I hit a stuck relocation on btrfs/061 during my overnight testing. This
turned out to be because we had left over extent entries in our extent
root for a data reloc inode that no longer existed. This happened
because in btrfs_drop_extents() we only update refs if we have SHAREABLE
set or we are the tree_root. This regression was introduced by
aeb935a455 ("btrfs: don't set SHAREABLE flag for data reloc tree")
where we stopped setting SHAREABLE for the data reloc tree.
The problem here is we actually do want to update extent references for
data extents in the data reloc tree, in fact we only don't want to
update extent references if the file extents are in the log tree.
Update this check to only skip updating references in the case of the
log tree.
This is relatively rare, because you have to be running scrub at the
same time, which is what btrfs/061 does. The data reloc inode has its
extents pre-allocated, and then we copy the extent into the
pre-allocated chunks. We theoretically should never be calling
btrfs_drop_extents() on a data reloc inode. The exception of course is
with scrub, if our pre-allocated extent falls inside of the block group
we are scrubbing, then the block group will be marked read only and we
will be forced to cow that extent. This means we will call
btrfs_drop_extents() on that range when we COW that file extent.
This isn't really problematic if we do this, the data reloc inode
requires that our extent lengths match exactly with the extent we are
copying, thankfully we validate the extent is correct with
get_new_location(), so if we happen to COW only part of the extent we
won't link it in when we do the relocation, so we are safe from any
other shenanigans that arise because of this interaction with scrub.
Fixes: aeb935a455 ("btrfs: don't set SHAREABLE flag for data reloc tree")
CC: stable@vger.kernel.org # 5.8+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cfd312695b upstream.
At replay_one_name(), we are treating any error from btrfs_lookup_inode()
as if the inode does not exists. Fix this by checking for an error and
returning it to the caller.
CC: stable@vger.kernel.org # 4.14+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52db77791f upstream.
At __inode_add_ref(), we treating any error returned from
btrfs_lookup_dir_item() or from btrfs_lookup_dir_index_item() as meaning
that there is no existing directory entry in the fs/subvolume tree.
This is not correct since we can get errors such as, for example, -EIO
when reading extent buffers while searching the fs/subvolume's btree.
So fix that and return the error to the caller when it is not -ENOENT.
CC: stable@vger.kernel.org # 4.14+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e15ac64137 upstream.
At replay_one_one(), we are treating any error returned from
btrfs_lookup_dir_item() or from btrfs_lookup_dir_index_item() as meaning
that there is no existing directory entry in the fs/subvolume tree.
This is not correct since we can get errors such as, for example, -EIO
when reading extent buffers while searching the fs/subvolume's btree.
So fix that and return the error to the caller when it is not -ENOENT.
CC: stable@vger.kernel.org # 4.14+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 171316a68d upstream.
The return type of ktime_divns() is s64. The timeout_to_jiffies() currently
assigns the result of this ktime_divns() to unsigned long, which on 32 bit
systems may overflow. Furthermore, the result of this function is sometimes
also passed to functions which expect signed long, dma_fence_wait_timeout()
is one such example.
Fix this by adjusting the type of remaining_jiffies to s64, so we do not
suffer overflow there, and return a value limited to range of 0..INT_MAX,
which is safe for all usecases of this timeout.
The above overflow can be triggered if userspace passes in too large timeout
value, larger than INT_MAX / HZ seconds. The kernel detects it and complains
about "schedule_timeout: wrong timeout value %lx" and generates a warning
backtrace.
Note that this fixes commit 6cedb8b377 ("drm/msm: avoid using 'timespec'"),
because the previously used timespec_to_jiffies() function returned unsigned
long instead of s64:
static inline unsigned long timespec_to_jiffies(const struct timespec *value)
Fixes: 6cedb8b377 ("drm/msm: avoid using 'timespec'")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jordan Crouse <jcrouse@codeaurora.org>
Cc: Rob Clark <robdclark@chromium.org>
Cc: stable@vger.kernel.org # 5.6+
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210917005913.157379-1-marex@denx.de
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e5809a4dd upstream.
For non-4K PAGE_SIZE configs, the largest gigantic huge page size is
CONT_PMD_SHIFT order. On arm64 with 64K PAGE_SIZE, the gigantic page is
16G. Therefore, one should be able to specify 'hugetlb_cma=16G' on the
kernel command line so that one gigantic page can be allocated from CMA.
However, when adding such an option the following message is produced:
hugetlb_cma: cma area should be at least 8796093022208 MiB
This is because the calculation for non-4K gigantic page order is
incorrect in the arm64 specific routine arm64_hugetlb_cma_reserve().
Fixes: abb7962adc ("arm64/hugetlb: Reserve CMA areas for gigantic pages on 16K and 64K configs")
Cc: <stable@vger.kernel.org> # 5.9.x
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Link: https://lore.kernel.org/r/20211005202529.213812-1-mike.kravetz@oracle.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af89ebaa64 upstream.
gpr_get() return the entire pt_regs (include sr) to userspace, if we
don't restore the C bit in gpr_set, it may break the ALU result in
that context. So the C flag bit is part of gpr context, that's why
riscv totally remove the C bit in the ISA. That makes sr reg clear
from userspace to supervisor privilege.
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fbd63c08cd upstream.
csky restore_sigcontext() blindly overwrites regs->sr with the value
it finds in sigcontext. Attacker can store whatever they want in there,
which includes things like S-bit. Userland shouldn't be able to set
that, or anything other than C flag (bit 0).
Do the same thing other architectures with protected bits in flags
register do - preserve everything that shouldn't be settable in
user mode, picking the rest from the value saved is sigcontext.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Guo Ren <guoren@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit be358af119 upstream.
I received a build failure for a new patch I'm working on the nds32
architecture, and when I went to test it, I couldn't get to my build error,
because it failed to build with a bunch of:
Error: invalid operands (*UND* and *UND* sections) for `^'
issues with various files. Those files were temporary asm files that looked
like: kernel/.tmp_mc_fork.s
I decided to look deeper, and found that the "mc" portion of that name
stood for "mcount", and was created by the recordmcount.pl script. One that
I wrote over a decade ago. Once I knew the source of the problem, I was
able to investigate it further.
The way the recordmcount.pl script works (BTW, there's a C version that
simply modifies the ELF object) is by doing an "objdump" on the object
file. Looks for all the calls to "mcount", and creates an offset of those
locations from some global variable it can use (usually a global function
name, found with <.*>:). Creates a asm file that is a table of references
to these locations, using the found variable/function. Compiles it and
links it back into the original object file. This asm file is called
".tmp_mc_<object_base_name>.s".
The problem here is that the objdump produced by the nds32 object file,
contains things that look like:
0000159a <.L3^B1>:
159a: c6 00 beqz38 $r6, 159a <.L3^B1>
159a: R_NDS32_9_PCREL_RELA .text+0x159e
159c: 84 d2 movi55 $r6, #-14
159e: 80 06 mov55 $r0, $r6
15a0: ec 3c addi10.sp #0x3c
Where ".L3^B1 is somehow selected as the "global" variable to index off of.
Then the assembly file that holds the mcount locations looks like this:
.section __mcount_loc,"a",@progbits
.align 2
.long .L3^B1 + -5522
.long .L3^B1 + -5384
.long .L3^B1 + -5270
.long .L3^B1 + -5098
.long .L3^B1 + -4970
.long .L3^B1 + -4758
.long .L3^B1 + -4122
[...]
And when it is compiled back to an object to link to the original object,
the compile fails on the "^" symbol.
Simple solution for now, is to have the perl script ignore using function
symbols that have an "^" in the name.
Link: https://lkml.kernel.org/r/20211014143507.4ad2c0f7@gandalf.local.home
Cc: stable@vger.kernel.org
Acked-by: Greentime Hu <green.hu@gmail.com>
Fixes: fbf58a52ac ("nds32/ftrace: Add RECORD_MCOUNT support")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a3fd1a986e upstream.
We need to define the codec pin 0x1b to be the mic, but somehow
the mic doesn't support hot plugging detection, and Windows also has
this issue, so we set it to phantom headset-mic.
Also the determine_headset_type() often returns the omtp type by a
mistake when we plug a ctia headset, this makes the mic can't record
sound at all. Because most of the headset are ctia type nowadays and
some machines have the fixed ctia type audio jack, it is possible this
machine has the fixed ctia jack too. Here we set this mic jack to
fixed ctia type, this could avoid the mic type detection mistake and
make the ctia headset work stable.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214537
Reported-and-tested-by: msd <msd.mmq@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20211012114748.5238-1-hui.wang@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd6dd6e3c7 upstream.
This applies a SND_PCI_QUIRK(...) to the TongFang PHxTxX1 barebone. This
fixes the issue of the internal Microphone not working after booting
another OS.
When booting a certain another OS this barebone keeps some coeff settings
even after a cold shutdown. These coeffs prevent the microphone detection
from working in Linux, making the Laptop think that there is always an
external microphone plugged-in and therefore preventing the use of the
internal one.
The relevant indexes and values where gathered by naively diff-ing and
reading a working and a non-working coeff dump.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211006130415.538243-1-wse@tuxedocomputers.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b987fe844 upstream.
The headphone mic is not working on Dell Latitude laptops with ALC3254.
The codec vendor id is 0x10ec0295 and share the same pincfg as defined
in ALC295_STANDARD_PINS. So the ALC269_FIXUP_DELL1_MIC_NO_PRESENCE will
be applied per alc269_pin_fixup_tbl[] but actually the headphone mic is
using NID 0x1b instead of 0x1a. The ALC269_FIXUP_DELL4_MIC_NO_PRESENCE
need to be applied instead.
Use ALC269_FIXUP_DELL4_MIC_NO_PRESENCE for particular models before
a generic fixup comes out.
Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211001062856.1037901-1-chris.chiu@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f8763c59c upstream.
John Keeping reported and posted a patch for a potential UAF in
rawmidi sequencer destruction: the snd_rawmidi_dev_seq_free() may be
called after the associated rawmidi object got already freed.
After a deeper look, it turned out that the bug is rather the
incorrect private_free call order for a snd_seq_device. The
snd_seq_device private_free gets called at the release callback of the
sequencer device object, while this was rather expected to be executed
at the snd_device call chains that runs at the beginning of the whole
card-free procedure. It's been broken since the rewrite of
sequencer-device binding (although it hasn't surfaced because the
sequencer device release happens usually right along with the card
device release).
This patch corrects the private_free call to be done in the right
place, at snd_seq_device_dev_free().
Fixes: 7c37ae5c62 ("ALSA: seq: Rewrite sequencer device binding with standard bus")
Reported-and-tested-by: John Keeping <john@metanate.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210930114114.8645-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 228af5a4fa upstream.
Michael Forney reported an incorrect padding type that was defined in
the commit 80fe7430c7 ("ALSA: add new 32-bit layout for
snd_pcm_mmap_status/control") for PCM control mmap data.
His analysis is correct, and this caused the misplacements of PCM
control data on 32bit arch and 32bit compat mode.
The bug is that the __pad2 definition in __snd_pcm_mmap_control64
struct was wrongly with __pad_before_uframe, which should have been
__pad_after_uframe instead. This struct is used in SYNC_PTR ioctl and
control mmap. Basically this bug leads to two problems:
- The offset of avail_min field becomes wrong, it's placed right after
appl_ptr without padding on little-endian
- When appl_ptr and avail_min are read as 64bit values in kernel side,
the values become either zero or corrupted (mixed up)
One good news is that, because both user-space and kernel
misunderstand the wrong offset, at least, 32bit application running on
32bit kernel works as is. Also, 64bit applications are unaffected
because the padding size is zero. The remaining problem is the 32bit
compat mode; as mentioned in the above, avail_min is placed right
after appl_ptr on little-endian archs, 64bit kernel reads bogus values
for appl_ptr updates, which may lead to streaming bugs like jumping,
XRUN or whatever unexpected.
(However, we haven't heard any serious bug reports due to this over
years, so practically seen, it's fairly safe to assume that the impact
by this bug is limited.)
Ideally speaking, we should correct the wrong mmap status control
definition. But this would cause again incompatibility with the
existing binaries, and fixing it (e.g. by renumbering ioctls) would be
really messy.
So, as of this patch, we only correct the behavior of 32bit compat
mode and keep the rest as is. Namely, the SYNC_PTR ioctl is now
handled differently in compat mode to read/write the 32bit values at
the right offsets. The control mmap of 32bit apps on 64bit kernels
has been already disabled (which is likely rather an overlook, but
this worked fine at this time :), so covering SYNC_PTR ioctl should
suffice as a fallback.
Fixes: 80fe7430c7 ("ALSA: add new 32-bit layout for snd_pcm_mmap_status/control")
Reported-by: Michael Forney <mforney@mforney.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Cc: <stable@vger.kernel.org>
Cc: Rich Felker <dalias@libc.org>
Link: https://lore.kernel.org/r/29QBMJU8DE71E.2YZSH8IHT5HMH@mforney.org
Link: https://lore.kernel.org/r/20211010075546.23220-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The get() method does not understand the on-the-wire encoding of the
remote GPIO states, thinking they are simple on/off bits when they are
really pairs of 16-bit counts. Rewrite the get() handler to return the
value last written, which will eventually match the actual GPIO state
if there are no other changes.
See: https://github.com/raspberrypi/linux/issues/4638
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
[ Upstream commit ebc69e897e ]
This reverts commit 2d52c58b9c.
We have had several folks complain that this causes hangs for them, which
is especially problematic as the commit has also hit stable already.
As no resolution seems to be forthcoming right now, revert the patch.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=214503
Fixes: 2d52c58b9c ("block, bfq: honor already-setup queue merges")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f067d5585c ]
The bytes for max_power_out from the ibm-cffps devices differ in byte
order for some power supplies.
The Witherspoon power supply returns the bytes in MSB/LSB order.
The Rainier power supply returns the bytes in LSB/MSB order.
The Witherspoon power supply uses version cffps1. The Rainier power
supply should use version cffps2. If version is cffps1, swap the bytes
before output to max_power_out.
Tested:
Witherspoon before: 3148. Witherspoon after: 3148.
Rainier before: 53255. Rainier after: 2000.
Signed-off-by: Brandon Wyman <bjwyman@gmail.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20210928205051.1222815-1-bjwyman@gmail.com
[groeck: Replaced yoda programming]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f792565326 ]
Users of rdpmc rely on the mmapped user page to calculate accurate
time_enabled. Currently, userpage->time_enabled is only updated when the
event is added to the pmu. As a result, inactive event (due to counter
multiplexing) does not have accurate userpage->time_enabled. This can
be reproduced with something like:
/* open 20 task perf_event "cycles", to create multiplexing */
fd = perf_event_open(); /* open task perf_event "cycles" */
userpage = mmap(fd); /* use mmap and rdmpc */
while (true) {
time_enabled_mmap = xxx; /* use logic in perf_event_mmap_page */
time_enabled_read = read(fd).time_enabled;
if (time_enabled_mmap > time_enabled_read)
BUG();
}
Fix this by updating userpage for inactive events in merge_sched_in.
Suggested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reported-and-tested-by: Lucian Grijincu <lucian@fb.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20210929194313.2398474-1-songliubraving@fb.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 103bde372f ]
When CONFIG_INET is not set, there are failing references to IPv4
functions, so make this driver depend on INET.
Fixes these build errors:
sparc64-linux-ld: drivers/net/ethernet/sun/sunvnet_common.o: in function `sunvnet_start_xmit_common':
sunvnet_common.c:(.text+0x1a68): undefined reference to `__icmp_send'
sparc64-linux-ld: drivers/net/ethernet/sun/sunvnet_common.o: in function `sunvnet_poll_common':
sunvnet_common.c:(.text+0x358c): undefined reference to `ip_send_check'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Aaron Young <aaron.young@oracle.com>
Cc: Rashmi Narasimhan <rashmi.narasimhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b3b353ef3 ]
Commit 9d682ea6bc ("vboxsf: Fix the check for the old binary
mount-arguments struct") was meant to fix a build error due to sign
mismatch in 'char' and the use of character constants, but it just moved
the error elsewhere, in that on some architectures characters and signed
and on others they are unsigned, and that's just how the C standard
works.
The proper fix is a simple "don't do that then". The code was just
being silly and odd, and it should never have cared about signed vs
unsigned characters in the first place, since what it is testing is not
four "characters", but four bytes.
And the way to compare four bytes is by using "memcmp()".
Which compilers will know to just turn into a single 32-bit compare with
a constant, as long as you don't have crazy debug options enabled.
Link: https://lore.kernel.org/lkml/20210927094123.576521-1-arnd@kernel.org/
Cc: Arnd Bergmann <arnd@kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b193e15ac6 ]
We observed below report when playing with netlink sock:
UBSAN: shift-out-of-bounds in net/sched/sch_api.c:580:10
shift exponent 249 is too large for 32-bit type
CPU: 0 PID: 685 Comm: a.out Not tainted
Call Trace:
dump_stack_lvl+0x8d/0xcf
ubsan_epilogue+0xa/0x4e
__ubsan_handle_shift_out_of_bounds+0x161/0x182
__qdisc_calculate_pkt_len+0xf0/0x190
__dev_queue_xmit+0x2ed/0x15b0
it seems like kernel won't check the stab log value passing from
user, and will use the insane value later to calculate pkt_len.
This patch just add a check on the size/cell_log to avoid insane
calculation.
Reported-by: Abaci <abaci@linux.alibaba.com>
Signed-off-by: Michael Wang <yun.wang@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4bb0bd81ce ]
When we have several pending signals, have entered with the kernel
with large exception frame *and* have already built at least one
sigframe, regs->stkadj is going to be non-zero and regs->format/sr/pc
are going to be junk - the real values are in shifted exception stack
frame we'd built when putting together the first sigframe.
If that happens, subsequent sigframes are going to be garbage.
Not hard to fix - just need to find the "adjusted" frame first
and look for format/vector/sr/pc in it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Finn Thain <fthain@linux-m68k.org>
Link: https://lore.kernel.org/r/YP2dBIAPTaVvHiZ6@zeniv-ca.linux.org.uk
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7970a19b71 ]
The ipv4 and device notifiers are called with RTNL mutex held.
The table walk can take some time, better not block other RTNL users.
'ip a' has been reported to block for up to 20 seconds when conntrack table
has many entries and device down events are frequent (e.g., PPP).
Reported-and-tested-by: Martin Zaharinov <micron10@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30db406923 ]
masq_inet6_event is called asynchronously from system work queue,
because the inet6 notifier is atomic and nf_iterate_cleanup can sleep.
The ipv4 and device notifiers call nf_iterate_cleanup directly.
This is legal, but these notifiers are called with RTNL mutex held.
A large conntrack table with many devices coming and going will have severe
impact on the system usability, with 'ip a' blocking for several seconds.
This change places the defer code into a helper and makes it more
generic so ipv4 and ifdown notifiers can be converted to defer the
cleanup walk as well in a follow patch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a8e1813ff ]
Invoke release_firmware() when the firmware fails to boot in
sof_probe_continue().
The request_firmware() framework must be informed of failures in
sof_probe_continue() otherwise its internal "batching"
feature (different from caching) cached the firmware image
forever. Attempts to correct the file in /lib/firmware/ were then
silently and confusingly ignored until the next reboot. Unloading the
drivers did not help because from their disconnected perspective the
firmware had failed so there was nothing to release.
Also leverage the new snd_sof_fw_unload() function to simplify the
snd_sof_device_remove() function.
Signed-off-by: Marc Herbert <marc.herbert@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20210916085008.28929-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c8fbaa553 ]
Add the new PIDs to wacom_wac.c to support the new models in the Intuos series.
[jkosina@suse.cz: fix changelog]
Signed-off-by: Joshua Dickens <joshua.dickens@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 310e2d43c3 ]
ip6tables only sets the `IP6T_F_PROTO` flag on a rule if a protocol is
specified (`-p tcp`, for example). However, if the flag is not set,
`ip6_packet_match` doesn't call `ipv6_find_hdr` for the skb, in which
case the fragment offset is left uninitialized and a garbage value is
passed to each matcher.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55ce2f649b ]
Current error path of ext4_write_inline_data_end() is not correct.
Firstly, it should pass out the error value if ext4_get_inode_loc()
return fail, or else it could trigger infinite loop if we inject error
here. And then it's better to add inode to orphan list if it return fail
in ext4_journal_stop(), otherwise we could not restore inline xattr
entry after power failure. Finally, we need to reset the 'ret' value if
ext4_write_inline_data_end() return success in ext4_write_end() and
ext4_journalled_write_end(), otherwise we could not get the error return
value of ext4_journal_stop().
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Link: https://lore.kernel.org/r/20210716122024.1105856-3-yi.zhang@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4df031ff58 ]
After commit 3da40c7b08 ("ext4: only call ext4_truncate when size <=
isize"), i_disksize could always be updated to i_size in ext4_setattr(),
and we could sure that i_disksize <= i_size since holding inode lock and
if i_disksize < i_size there are delalloc writes pending in the range
upto i_size. If the end of the current write is <= i_size, there's no
need to touch i_disksize since writeback will push i_disksize upto
i_size eventually. So we can switch to check i_size instead of
i_disksize in ext4_da_write_end() when write to the end of the file.
we also could remove ext4_mark_inode_dirty() together because we defer
inode dirtying to generic_write_end() or ext4_da_write_inline_data_end().
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Link: https://lore.kernel.org/r/20210716122024.1105856-2-yi.zhang@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
In order to resolve a potential startup order bug, the vcio driver has
been rewritten as a platform driver that depends on a DT node for
its instantiation and to locate the firmware driver.
Add that DT node.
See: https://github.com/raspberrypi/linux/issues/4620
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The old vcio driver is a simple character device that manually locates
the firmware driver. Initialising it before the firmware driver causes
a failure, and no retries are attempted.
Rewrite vcio as a platform driver that depends on a DT node for its
instantiation and the location of the firmware driver, making use of
the miscdevice framework to reduce the code size.
N.B. Using miscdevice changes the udev SUBSYSTEM string, so a change
to the companion udev rule is required in order to continue to set
the correct device permissions, e.g.:
KERNEL="vcio", GROUP="video", MODE="0660"
See: https://github.com/raspberrypi/linux/issues/4620
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Power-on reset after the insertion of a battery does not always complete
successfully, leading to corrupted register content. The EXT_TEST bit
will stop the clock from running, but currently the driver will never
recover.
Safely handle the erroneous state by clearing EXT_TEST as part of the
usual set_time method.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Using the rpi_firmware API as intended allows proper reference counting
of the firmware device and means we can remove a downstream patch to
the firmware driver.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Using the rpi_firmware API as intended allows proper reference counting
of the firmware device and means we can remove a downstream patch to
the firmware driver.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
For cases where spare PWM outputs are available, but are desired
to be addressed a standard outputs instead.
Wraps a PWM channel as a new GPIO chip with the one output.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
commit e8f71f8923 upstream.
nvkm test builds fail with the following error.
drivers/gpu/drm/nouveau/nvkm/engine/device/ctrl.c: In function 'nvkm_control_mthd_pstate_info':
drivers/gpu/drm/nouveau/nvkm/engine/device/ctrl.c:60:35: error: overflow in conversion from 'int' to '__s8' {aka 'signed char'} changes value from '-251' to '5'
The code builds on most architectures, but fails on parisc where ENOSYS
is defined as 251.
Replace the error code with -ENODEV (-19). The actual error code does
not really matter and is not passed to userspace - it just has to be
negative.
Fixes: 7238eca4cf ("drm/nouveau: expose pstate selection per-power source in sysfs")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9848417926 ]
The intel powerclamp driver will setup a per-CPU worker with RT
priority. The worker will then invoke play_idle() in which it remains in
the idle poll loop until it is stopped by the timer it started earlier.
That timer needs to expire in hard interrupt context on PREEMPT_RT.
Otherwise the timer will expire in ksoftirqd as a SOFT timer but that task
won't be scheduled on the CPU because its priority is lower than the
priority of the worker which is in the idle loop.
Always expire the idle timer in hard interrupt context.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210906113034.jgfxrjdvxnjqgtmc@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 884f0e84f1 ]
The pending timer has been set up in blk_throtl_init(). However, the
timer is not deleted in blk_throtl_exit(). This means that the timer
handler may still be running after freeing the timer, which would
result in a use-after-free.
Fix by calling del_timer_sync() to delete the timer in blk_throtl_exit().
Signed-off-by: Li Jinlin <lijinlin3@huawei.com>
Link: https://lore.kernel.org/r/20210907121242.2885564-1-lijinlin3@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d44084c934 ]
A consumer is expected to disable a PWM before calling pwm_put(). And if
they didn't there is hopefully a good reason (or the consumer needs
fixing). Also if disabling an enabled PWM was the right thing to do,
this should better be done in the framework instead of in each low level
driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d768cd7fd ]
A consumer is expected to disable a PWM before calling pwm_put(). And if
they didn't there is hopefully a good reason (or the consumer needs
fixing). Also if disabling an enabled PWM was the right thing to do,
this should better be done in the framework instead of in each low level
driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c68eb29c8e ]
A consumer is expected to disable a PWM before calling pwm_put(). And if
they didn't there is hopefully a good reason (or the consumer needs
fixing). Also if disabling an enabled PWM was the right thing to do,
this should better be done in the framework instead of in each low level
driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6c849012b ]
Currently there is no validity check for event ID received from F/W,
Thus exposing driver to memory overrun.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f5dec07ac ]
Patch series "nilfs2: fix incorrect usage of kobject".
This patchset from Nanyong Sun fixes memory leak issues and a NULL
pointer dereference issue caused by incorrect usage of kboject in nilfs2
sysfs implementation.
This patch (of 6):
Reported by syzkaller:
BUG: memory leak
unreferenced object 0xffff888100ca8988 (size 8):
comm "syz-executor.1", pid 1930, jiffies 4294745569 (age 18.052s)
hex dump (first 8 bytes):
6c 6f 6f 70 31 00 ff ff loop1...
backtrace:
kstrdup+0x36/0x70 mm/util.c:60
kstrdup_const+0x35/0x60 mm/util.c:83
kvasprintf_const+0xf1/0x180 lib/kasprintf.c:48
kobject_set_name_vargs+0x56/0x150 lib/kobject.c:289
kobject_add_varg lib/kobject.c:384 [inline]
kobject_init_and_add+0xc9/0x150 lib/kobject.c:473
nilfs_sysfs_create_device_group+0x150/0x7d0 fs/nilfs2/sysfs.c:986
init_nilfs+0xa21/0xea0 fs/nilfs2/the_nilfs.c:637
nilfs_fill_super fs/nilfs2/super.c:1046 [inline]
nilfs_mount+0x7b4/0xe80 fs/nilfs2/super.c:1316
legacy_get_tree+0x105/0x210 fs/fs_context.c:592
vfs_get_tree+0x8e/0x2d0 fs/super.c:1498
do_new_mount fs/namespace.c:2905 [inline]
path_mount+0xf9b/0x1990 fs/namespace.c:3235
do_mount+0xea/0x100 fs/namespace.c:3248
__do_sys_mount fs/namespace.c:3456 [inline]
__se_sys_mount fs/namespace.c:3433 [inline]
__x64_sys_mount+0x14b/0x1f0 fs/namespace.c:3433
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3b/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
If kobject_init_and_add return with error, then the cleanup of kobject
is needed because memory may be allocated in kobject_init_and_add
without freeing.
And the place of cleanup_dev_kobject should use kobject_put to free the
memory associated with the kobject. As the section "Kobject removal" of
"Documentation/core-api/kobject.rst" says, kobject_del() just makes the
kobject "invisible", but it is not cleaned up. And no more cleanup will
do after cleanup_dev_kobject, so kobject_put is needed here.
Link: https://lkml.kernel.org/r/1625651306-10829-1-git-send-email-konishi.ryusuke@gmail.com
Link: https://lkml.kernel.org/r/1625651306-10829-2-git-send-email-konishi.ryusuke@gmail.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Link: https://lkml.kernel.org/r/20210629022556.3985106-2-sunnanyong@huawei.com
Signed-off-by: Nanyong Sun <sunnanyong@huawei.com>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f96a5bfa1 ]
We update the ctime/mtime of a block device when we remove it so that
blkid knows the device changed. However we do this by re-opening the
block device and calling filp_update_time. This is more correct because
it'll call the inode->i_op->update_time if it exists, but the block dev
inodes do not do this. Instead call generic_update_time() on the
bd_inode in order to avoid the blkdev_open path and get rid of the
following lockdep splat:
======================================================
WARNING: possible circular locking dependency detected
5.14.0-rc2+ #406 Not tainted
------------------------------------------------------
losetup/11596 is trying to acquire lock:
ffff939640d2f538 ((wq_completion)loop0){+.+.}-{0:0}, at: flush_workqueue+0x67/0x5e0
but task is already holding lock:
ffff939655510c68 (&lo->lo_mutex){+.+.}-{3:3}, at: __loop_clr_fd+0x41/0x660 [loop]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #4 (&lo->lo_mutex){+.+.}-{3:3}:
__mutex_lock+0x7d/0x750
lo_open+0x28/0x60 [loop]
blkdev_get_whole+0x25/0xf0
blkdev_get_by_dev.part.0+0x168/0x3c0
blkdev_open+0xd2/0xe0
do_dentry_open+0x161/0x390
path_openat+0x3cc/0xa20
do_filp_open+0x96/0x120
do_sys_openat2+0x7b/0x130
__x64_sys_openat+0x46/0x70
do_syscall_64+0x38/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
-> #3 (&disk->open_mutex){+.+.}-{3:3}:
__mutex_lock+0x7d/0x750
blkdev_get_by_dev.part.0+0x56/0x3c0
blkdev_open+0xd2/0xe0
do_dentry_open+0x161/0x390
path_openat+0x3cc/0xa20
do_filp_open+0x96/0x120
file_open_name+0xc7/0x170
filp_open+0x2c/0x50
btrfs_scratch_superblocks.part.0+0x10f/0x170
btrfs_rm_device.cold+0xe8/0xed
btrfs_ioctl+0x2a31/0x2e70
__x64_sys_ioctl+0x80/0xb0
do_syscall_64+0x38/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
-> #2 (sb_writers#12){.+.+}-{0:0}:
lo_write_bvec+0xc2/0x240 [loop]
loop_process_work+0x238/0xd00 [loop]
process_one_work+0x26b/0x560
worker_thread+0x55/0x3c0
kthread+0x140/0x160
ret_from_fork+0x1f/0x30
-> #1 ((work_completion)(&lo->rootcg_work)){+.+.}-{0:0}:
process_one_work+0x245/0x560
worker_thread+0x55/0x3c0
kthread+0x140/0x160
ret_from_fork+0x1f/0x30
-> #0 ((wq_completion)loop0){+.+.}-{0:0}:
__lock_acquire+0x10ea/0x1d90
lock_acquire+0xb5/0x2b0
flush_workqueue+0x91/0x5e0
drain_workqueue+0xa0/0x110
destroy_workqueue+0x36/0x250
__loop_clr_fd+0x9a/0x660 [loop]
block_ioctl+0x3f/0x50
__x64_sys_ioctl+0x80/0xb0
do_syscall_64+0x38/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
other info that might help us debug this:
Chain exists of:
(wq_completion)loop0 --> &disk->open_mutex --> &lo->lo_mutex
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&lo->lo_mutex);
lock(&disk->open_mutex);
lock(&lo->lo_mutex);
lock((wq_completion)loop0);
*** DEADLOCK ***
1 lock held by losetup/11596:
#0: ffff939655510c68 (&lo->lo_mutex){+.+.}-{3:3}, at: __loop_clr_fd+0x41/0x660 [loop]
stack backtrace:
CPU: 1 PID: 11596 Comm: losetup Not tainted 5.14.0-rc2+ #406
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.13.0-2.fc32 04/01/2014
Call Trace:
dump_stack_lvl+0x57/0x72
check_noncircular+0xcf/0xf0
? stack_trace_save+0x3b/0x50
__lock_acquire+0x10ea/0x1d90
lock_acquire+0xb5/0x2b0
? flush_workqueue+0x67/0x5e0
? lockdep_init_map_type+0x47/0x220
flush_workqueue+0x91/0x5e0
? flush_workqueue+0x67/0x5e0
? verify_cpu+0xf0/0x100
drain_workqueue+0xa0/0x110
destroy_workqueue+0x36/0x250
__loop_clr_fd+0x9a/0x660 [loop]
? blkdev_ioctl+0x8d/0x2a0
block_ioctl+0x3f/0x50
__x64_sys_ioctl+0x80/0xb0
do_syscall_64+0x38/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6d37ccdd2 ]
capsnaps will take inode references via ihold when queueing to flush.
When force unmounting, the client will just close the sessions and
may never get a flush reply, causing a leak and inode ref leak.
Fix this by removing the capsnaps for an inode when removing the caps.
URL: https://tracker.ceph.com/issues/52295
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b11ed50346 ]
The current code will update the mtime and then try to get caps to
handle the write. If we end up having to request caps from the MDS, then
the mtime in the cap grant will clobber the updated mtime and it'll be
lost.
This is most noticable when two clients are alternately writing to the
same file. Fw caps are continually being granted and revoked, and the
mtime ends up stuck because the updated mtimes are always being
overwritten with the old one.
Fix this by changing the order of operations in ceph_write_iter to get
the caps before updating the times. Also, make sure we check the pool
full conditions before even getting any caps or uninlining.
URL: https://tracker.ceph.com/issues/46574
Reported-by: Jozef Kováč <kovac@firma.zoznam.sk>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Luis Henriques <lhenriques@suse.de>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aac6c0f907 ]
The xilinx dma driver uses the consistent allocations, so for correct
operation also set the DMA mask for coherent APIs. It fixes the below
kernel crash with dmatest client when DMA IP is configured with 64-bit
address width and linux is booted from high (>4GB) memory.
Call trace:
[ 489.531257] dma_alloc_from_pool+0x8c/0x1c0
[ 489.535431] dma_direct_alloc+0x284/0x330
[ 489.539432] dma_alloc_attrs+0x80/0xf0
[ 489.543174] dma_pool_alloc+0x160/0x2c0
[ 489.547003] xilinx_cdma_prep_memcpy+0xa4/0x180
[ 489.551524] dmatest_func+0x3cc/0x114c
[ 489.555266] kthread+0x124/0x130
[ 489.558486] ret_from_fork+0x10/0x3c
[ 489.562051] ---[ end trace 248625b2d596a90a ]---
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Reviewed-by: Harini Katakam <harini.katakam@xilinx.com>
Link: https://lore.kernel.org/r/1629363528-30347-1-git-send-email-radhey.shyam.pandey@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3811a50ad ]
Currently, iommu_init_ga() checks and disables IOMMU VAPIC support
(i.e. AMD AVIC support in IOMMU) when GAMSup feature bit is not set.
However it forgets to clear IRQ_POSTING_CAP from the previously set
amd_iommu_irq_ops.capability.
This triggers an invalid page fault bug during guest VM warm reboot
if AVIC is enabled since the irq_remapping_cap(IRQ_POSTING_CAP) is
incorrectly set, and crash the system with the following kernel trace.
BUG: unable to handle page fault for address: 0000000000400dd8
RIP: 0010:amd_iommu_deactivate_guest_mode+0x19/0xbc
Call Trace:
svm_set_pi_irte_mode+0x8a/0xc0 [kvm_amd]
? kvm_make_all_cpus_request_except+0x50/0x70 [kvm]
kvm_request_apicv_update+0x10c/0x150 [kvm]
svm_toggle_avic_for_irq_window+0x52/0x90 [kvm_amd]
svm_enable_irq_window+0x26/0xa0 [kvm_amd]
vcpu_enter_guest+0xbbe/0x1560 [kvm]
? avic_vcpu_load+0xd5/0x120 [kvm_amd]
? kvm_arch_vcpu_load+0x76/0x240 [kvm]
? svm_get_segment_base+0xa/0x10 [kvm_amd]
kvm_arch_vcpu_ioctl_run+0x103/0x590 [kvm]
kvm_vcpu_ioctl+0x22a/0x5d0 [kvm]
__x64_sys_ioctl+0x84/0xc0
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xae
Fixes by moving the initializing of AMD IOMMU interrupt remapping mode
(amd_iommu_guest_ir) earlier before setting up the
amd_iommu_irq_ops.capability with appropriate IRQ_POSTING_CAP flag.
[joro: Squashed the two patches and limited
check_features_on_all_iommus() to CONFIG_IRQ_REMAP
to fix a compile warning.]
Signed-off-by: Wei Huang <wei.huang2@amd.com>
Co-developed-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Link: https://lore.kernel.org/r/20210820202957.187572-2-suravee.suthikulpanit@amd.com
Link: https://lore.kernel.org/r/20210820202957.187572-3-suravee.suthikulpanit@amd.com
Fixes: 8bda0cfbdc ("iommu/amd: Detect and initialize guest vAPIC log")
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 907872baa9 ]
parisc build test images fail to compile with the following error.
drivers/parisc/dino.c:160:12: error:
'pci_dev_is_behind_card_dino' defined but not used
Move the function just ahead of its only caller to avoid the error.
Fixes: 5fa1659105 ("parisc: Disable HP HSC-PCI Cards to prevent kernel crash")
Cc: Helge Deller <deller@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b92d4add5 ]
DEFINE_SMP_CALL_CACHE_FUNCTION() was usefel before the CPU hotplug rework
to ensure that the cache related functions are called on the upcoming CPU
because the notifier itself could run on any online CPU.
The hotplug state machine guarantees that the callbacks are invoked on the
upcoming CPU. So there is no need to have this SMP function call
obfuscation. That indirection was missed when the hotplug notifiers were
converted.
This also solves the problem of ARM64 init_cache_level() invoking ACPI
functions which take a semaphore in that context. That's invalid as SMP
function calls run with interrupts disabled. Running it just from the
callback in context of the CPU hotplug thread solves this.
Fixes: 8571890e15 ("arm64: Add support for ACPI based firmware tables")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Will Deacon <will@kernel.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/871r69ersb.ffs@tglx
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3dc549986 ]
Due to high latency in PCIE clock switching on RKL platforms,
switching the PCIE clock dynamically at runtime can lead to HDMI/DP
audio problems. On newer asics this is handled in the SMU firmware.
For SMU7-based asics, disable PCIE clock switching to avoid the issue.
AMD provide a parameter to disable PICE_DPM.
modprobe amdgpu ppfeaturemask=0xfff7bffb
It's better to contorl PCIE_DPM in amd gpu driver,
switch PCI_DPM by determining intel RKL platform for SMU7-based asics.
Fixes: 1a31474cdb ("drm/amd/pm: workaround for audio noise issue")
Ref: https://lists.freedesktop.org/archives/amd-gfx/2021-August/067413.html
Signed-off-by: Koba Ko <koba.ko@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb83610762 ]
There are two pairs of declarations for thermal_cooling_device_register()
and thermal_of_cooling_device_register(), and only one set was changed
in a recent patch, so the other one now causes a compile-time warning:
drivers/net/wireless/mediatek/mt76/mt7915/init.c: In function 'mt7915_thermal_init':
drivers/net/wireless/mediatek/mt76/mt7915/init.c:134:48: error: passing argument 1 of 'thermal_cooling_device_register' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
134 | cdev = thermal_cooling_device_register(wiphy_name(wiphy), phy,
| ^~~~~~~~~~~~~~~~~
In file included from drivers/net/wireless/mediatek/mt76/mt7915/init.c:7:
include/linux/thermal.h:407:39: note: expected 'char *' but argument is of type 'const char *'
407 | thermal_cooling_device_register(char *type, void *devdata,
| ~~~~~~^~~~
Change the dummy helper functions to have the same arguments as the
normal version.
Fixes: f991de53a8 ("thermal: make device_register's type argument const")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210722090717.1116748-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4002173b7 ]
The first thing metric_delayed_work does is check mdsc->stopping,
and then return immediately if it's set. That's good since we would
have already torn down the metric structures at this point, otherwise,
but there is no locking around mdsc->stopping.
It's possible that the ceph_metric_destroy call could race with the
delayed_work, in which case we could end up with the delayed_work
accessing destroyed percpu variables.
At this point in the mdsc teardown, the "stopping" flag has already been
set, so there's no benefit to flushing the work. Move the work
cancellation in ceph_metric_destroy ahead of the percpu variable
destruction, and eliminate the flush_delayed_work call in
ceph_mdsc_destroy.
Fixes: 18f473b384 ("ceph: periodically send perf metrics to MDSes")
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Xiubo Li <xiubli@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d453ceb654 ]
Add trace event to report samples and their timestamp coming from the
EC. It allows to check if the timestamps are correct and the filter is
working correctly without introducing too much latency.
To enable these events:
cd /sys/kernel/debug/tracing/
echo 1 > events/cros_ec/enable
echo 0 > events/cros_ec/cros_ec_request_start/enable
echo 0 > events/cros_ec/cros_ec_request_done/enable
echo 1 > tracing_on
cat trace_pipe
Observe event flowing:
irq/105-chromeo-95 [000] .... 613.659758: cros_ec_sensorhub_timestamp: ...
irq/105-chromeo-95 [000] .... 613.665219: cros_ec_sensorhub_filter: dx: ...
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 020162d6f4 upstream.
This fixes a race condition: After pwmchip_add() is called there might
already be a consumer and then modifying the hardware behind the
consumer's back is bad. So reset before calling pwmchip_add().
Note that reseting the hardware isn't the right thing to do if the PWM
is already running as it might e.g. disable (or even enable) a backlight
that is supposed to be on (or off).
Fixes: 4dce82c1e8 ("pwm: add pwm-mxs support")
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d2813fb17 upstream.
This fixes a race condition: After pwmchip_add() is called there might
already be a consumer and then modifying the hardware behind the
consumer's back is bad. So set the default before.
(Side-note: I don't know what this register setting actually does, if
this modifies the polarity there is an inconsistency because the
inversed polarity isn't considered if the PWM is already running during
.probe().)
Fixes: acfd92fdfb ("pwm: lpc32xx: Set PWM_PIN_LEVEL bit to default value")
Cc: Sylvain Lemieux <slemieux@tycoint.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a9344cd0a upstream.
There are variables(power.may_skip_resume and dev->power.must_resume)
and DPM_FLAG_MAY_SKIP_RESUME flags to control the resume of devices after
a system wide suspend transition.
Setting the DPM_FLAG_MAY_SKIP_RESUME flag means that the driver allows
its "noirq" and "early" resume callbacks to be skipped if the device
can be left in suspend after a system-wide transition into the working
state. PM core determines that the driver's "noirq" and "early" resume
callbacks should be skipped or not with dev_pm_skip_resume() function by
checking power.may_skip_resume variable.
power.must_resume variable is getting set to false in __device_suspend()
function without checking device's DPM_FLAG_MAY_SKIP_RESUME settings.
In problematic scenario, where all the devices in the suspend_late
stage are successful and some device can fail to suspend in
suspend_noirq phase. So some devices successfully suspended in suspend_late
stage are not getting chance to execute __device_suspend_noirq()
to set dev->power.must_resume variable to true and not getting
resumed in early_resume phase.
Add a check for device's DPM_FLAG_MAY_SKIP_RESUME flag before
setting power.must_resume variable in __device_suspend function.
Fixes: 6e176bf8d4 ("PM: sleep: core: Do not skip callbacks in the resume phase")
Signed-off-by: Prasad Sodagudi <psodagud@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98e2e409e7 upstream.
When the refcount is decreased to 0, the resource reclamation branch is
entered. Before CPU0 reaches the race point (1), CPU1 may obtain the
spinlock and traverse the rbtree to find 'root', see
nilfs_lookup_root().
Although CPU1 will call refcount_inc() to increase the refcount, it is
obviously too late. CPU0 will release 'root' directly, CPU1 then
accesses 'root' and triggers UAF.
Use refcount_dec_and_lock() to ensure that both the operations of
decrease refcount to 0 and link deletion are lock protected eliminates
this risk.
CPU0 CPU1
nilfs_put_root():
<-------- (1)
spin_lock(&nilfs->ns_cptree_lock);
rb_erase(&root->rb_node, &nilfs->ns_cptree);
spin_unlock(&nilfs->ns_cptree_lock);
kfree(root);
<-------- use-after-free
refcount_t: underflow; use-after-free.
WARNING: CPU: 2 PID: 9476 at lib/refcount.c:28 \
refcount_warn_saturate+0x1cf/0x210 lib/refcount.c:28
Modules linked in:
CPU: 2 PID: 9476 Comm: syz-executor.0 Not tainted 5.10.45-rc1+ #3
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), ...
RIP: 0010:refcount_warn_saturate+0x1cf/0x210 lib/refcount.c:28
... ...
Call Trace:
__refcount_sub_and_test include/linux/refcount.h:283 [inline]
__refcount_dec_and_test include/linux/refcount.h:315 [inline]
refcount_dec_and_test include/linux/refcount.h:333 [inline]
nilfs_put_root+0xc1/0xd0 fs/nilfs2/the_nilfs.c:795
nilfs_segctor_destroy fs/nilfs2/segment.c:2749 [inline]
nilfs_detach_log_writer+0x3fa/0x570 fs/nilfs2/segment.c:2812
nilfs_put_super+0x2f/0xf0 fs/nilfs2/super.c:467
generic_shutdown_super+0xcd/0x1f0 fs/super.c:464
kill_block_super+0x4a/0x90 fs/super.c:1446
deactivate_locked_super+0x6a/0xb0 fs/super.c:335
deactivate_super+0x85/0x90 fs/super.c:366
cleanup_mnt+0x277/0x2e0 fs/namespace.c:1118
__cleanup_mnt+0x15/0x20 fs/namespace.c:1125
task_work_run+0x8e/0x110 kernel/task_work.c:151
tracehook_notify_resume include/linux/tracehook.h:188 [inline]
exit_to_user_mode_loop kernel/entry/common.c:164 [inline]
exit_to_user_mode_prepare+0x13c/0x170 kernel/entry/common.c:191
syscall_exit_to_user_mode+0x16/0x30 kernel/entry/common.c:266
do_syscall_64+0x45/0x80 arch/x86/entry/common.c:56
entry_SYSCALL_64_after_hwframe+0x44/0xa9
There is no reproduction program, and the above is only theoretical
analysis.
Link: https://lkml.kernel.org/r/1629859428-5906-1-git-send-email-konishi.ryusuke@gmail.com
Fixes: ba65ae4729 ("nilfs2: add checkpoint tree to nilfs object")
Link: https://lkml.kernel.org/r/20210723012317.4146-1-thunder.leizhen@huawei.com
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e1fbbd0731 upstream.
Keno Fischer reported that when a binray loaded via ld-linux-x the
prctl(PR_SET_MM_MAP) doesn't allow to setup brk value because it lays
before mm:end_data.
For example a test program shows
| # ~/t
|
| start_code 401000
| end_code 401a15
| start_stack 7ffce4577dd0
| start_data 403e10
| end_data 40408c
| start_brk b5b000
| sbrk(0) b5b000
and when executed via ld-linux
| # /lib64/ld-linux-x86-64.so.2 ~/t
|
| start_code 7fc25b0a4000
| end_code 7fc25b0c4524
| start_stack 7fffcc6b2400
| start_data 7fc25b0ce4c0
| end_data 7fc25b0cff98
| start_brk 55555710c000
| sbrk(0) 55555710c000
This of course prevent criu from restoring such programs. Looking into
how kernel operates with brk/start_brk inside brk() syscall I don't see
any problem if we allow to setup brk/start_brk without checking for
end_data. Even if someone pass some weird address here on a purpose then
the worst possible result will be an unexpected unmapping of existing vma
(own vma, since prctl works with the callers memory) but test for
RLIMIT_DATA is still valid and a user won't be able to gain more memory in
case of expanding VMAs via new values shipped with prctl call.
Link: https://lkml.kernel.org/r/20210121221207.GB2174@grain
Fixes: bbdc6076d2 ("binfmt_elf: move brk out of mmap when doing direct loader exec")
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Reported-by: Keno Fischer <keno@juliacomputing.com>
Acked-by: Andrey Vagin <avagin@gmail.com>
Tested-by: Andrey Vagin <avagin@gmail.com>
Cc: Dmitry Safonov <0x7f454c46@gmail.com>
Cc: Kirill Tkhai <ktkhai@virtuozzo.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Cc: Alexander Mikhalitsyn <alexander.mikhalitsyn@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a86d41404 upstream.
Currently perf saves a build-id with size but old versions assumes the
size of 20. In case the build-id is less than 20 (like for MD5), it'd
fill the rest with 0s.
I saw a problem when old version of perf record saved a binary in the
build-id cache and new version of perf reads the data. The symbols
should be read from the build-id cache (as the path no longer has the
same binary) but it failed due to mismatch in the build-id.
symsrc__init: build id mismatch for /home/namhyung/.debug/.build-id/53/e4c2f42a4c61a2d632d92a72afa08f00000000/elf.
The build-id event in the data has 20 byte build-ids, but it saw a
different size (16) when it reads the build-id of the elf file in the
build-id cache.
$ readelf -n ~/.debug/.build-id/53/e4c2f42a4c61a2d632d92a72afa08f00000000/elf
Displaying notes found in: .note.gnu.build-id
Owner Data size Description
GNU 0x00000010 NT_GNU_BUILD_ID (unique build ID bitstring)
Build ID: 53e4c2f42a4c61a2d632d92a72afa08f
Let's fix this by allowing trailing zeros if the size is different.
Fixes: 39be8d0115 ("perf tools: Pass build_id object to dso__build_id_equal()")
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20210910224630.1084877-1-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 099ec97ac9 upstream.
clang warns:
drivers/staging/rtl8192u/r8192U_core.c:4268:20: warning: bitwise and of
boolean expressions; did you mean logical and? [-Wbool-operation-and]
bpacket_toself = bpacket_match_bssid &
^~~~~~~~~~~~~~~~~~~~~
&&
1 warning generated.
Replace the bitwise AND with a logical one to clear up the warning, as
that is clearly what was intended.
Fixes: 8fc8598e61 ("Staging: Added Realtek rtl8192u driver to staging")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20210814235625.1780033-1-nathan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef6c8d6ccf upstream.
When SCTP handles an INIT chunk, it calls for example:
sctp_sf_do_5_1B_init
sctp_verify_init
sctp_verify_param
sctp_process_init
sctp_process_param
handling of SCTP_PARAM_SET_PRIMARY
sctp_verify_init() wasn't doing proper size validation and neither the
later handling, allowing it to work over the chunk itself, possibly being
uninitialized memory.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6ffe7671b upstream.
In one of the fallbacks that SCTP has for identifying an association for an
incoming packet, it looks for AddIp chunk (from ASCONF) and take a peek.
Thing is, at this stage nothing was validating that the chunk actually had
enough content for that, allowing the peek to happen over uninitialized
memory.
Similar check already exists in actual asconf handling in
sctp_verify_asconf().
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fcf044891c upstream.
We do not need a SWIOTLB unless we have DRAM that is addressable beyond
the arm_dma_limit. Compare max_pfn with arm_dma_pfn_limit to determine
whether we do need a SWIOTLB to be initialized.
Fixes: ad3c7b18c5 ("arm: use swiotlb for bounce buffering on LPAE configs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8b92b8c1e upstream.
We should not walk/touch page tables outside of VMA boundaries when
holding only the mmap sem in read mode. Evil user space can modify the
VMA layout just before this function runs and e.g., trigger races with
page table removal code since commit dd2283f260 ("mm: mmap: zap pages
with read mmap_sem in munmap").
find_vma() does not check if the address is >= the VMA start address;
use vma_lookup() instead.
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Fixes: dd2283f260 ("mm: mmap: zap pages with read mmap_sem in munmap")
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a2b2eb556 upstream.
The Linux console's VT102 implementation already consumes OSC
("Operating System Command") sequences, probably because that's how
palette changes are transmitted.
In addition to OSC, there are three other major clases of ANSI control
strings: APC ("Application Program Command"), PM ("Privacy Message"),
and DCS ("Device Control String"). They are handled similarly to OSC in
terms of termination.
Source: vt100.net
Add three new enumerated states, one for each of these types. All three
are handled the same way right now--they simply consume input until
terminated. I hope to expand upon this firmament in the future. Add
new predicate ansi_control_string(), returning true for any of these
states. Replace explicit checks against ESosc with calls to this
function. Transition to these states appropriately from the escape
initiation (ESesc) state.
This was motivated by the following Notcurses bugs:
https://github.com/dankamongmen/notcurses/issues/2050https://github.com/dankamongmen/notcurses/issues/1828https://github.com/dankamongmen/notcurses/issues/2069
where standard VT sequences are not consumed by the Linux console. It's
not necessary that the Linux console *support* these sequences, but it
ought *consume* these well-specified classes of sequences.
Tested by sending a variety of escape sequences to the console, and
verifying that they still worked, or were now properly consumed.
Verified that the escapes were properly terminated at a generic level.
Verified that the Notcurses tools continued to show expected output on
the Linux console, except now without escape bleedthrough.
Link: https://lore.kernel.org/lkml/YSydL0q8iaUfkphg@schwarzgerat.orthanc/
Signed-off-by: nick black <dankamongmen@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 02319bf15a upstream.
After d12e1c4649 ("net: dsa: b53: Set correct number of ports in the
DSA struct") we stopped setting dsa_switch::num_ports to DSA_MAX_PORTS,
which created an off by one error between the statically allocated
bcm_sf2_priv::port_sts array (of size DSA_MAX_PORTS). When
dsa_is_cpu_port() is used, we end-up accessing an out of bounds member
and causing a NPD.
Fix this by iterating with the appropriate port count using
ds->num_ports.
Fixes: d12e1c4649 ("net: dsa: b53: Set correct number of ports in the DSA struct")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eca4cf12ac upstream.
The recent patch has introduced a regression by not reading the reset
count in the ERROR_RECOVERY async event handler. We may have just
gone through a reset and the reset count has just incremented. If
we don't update the reset count in the ERROR_RECOVERY event handler,
the health check timer will see that the reset count has changed and
will initiate an unintended reset.
Restore the unconditional update of the reset count in
bnxt_async_event_process() if error recovery watchdog is enabled.
Also, update the reset count at the end of the reset sequence to
make it even more robust.
Fixes: 1b2b918319 ("bnxt_en: Fix possible unintended driver initiated error recovery")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81065b35e2 upstream.
There are two cases for machine check recovery:
1) The machine check was triggered by ring3 (application) code.
This is the simpler case. The machine check handler simply queues
work to be executed on return to user. That code unmaps the page
from all users and arranges to send a SIGBUS to the task that
triggered the poison.
2) The machine check was triggered in kernel code that is covered by
an exception table entry. In this case the machine check handler
still queues a work entry to unmap the page, etc. but this will
not be called right away because the #MC handler returns to the
fix up code address in the exception table entry.
Problems occur if the kernel triggers another machine check before the
return to user processes the first queued work item.
Specifically, the work is queued using the ->mce_kill_me callback
structure in the task struct for the current thread. Attempting to queue
a second work item using this same callback results in a loop in the
linked list of work functions to call. So when the kernel does return to
user, it enters an infinite loop processing the same entry for ever.
There are some legitimate scenarios where the kernel may take a second
machine check before returning to the user.
1) Some code (e.g. futex) first tries a get_user() with page faults
disabled. If this fails, the code retries with page faults enabled
expecting that this will resolve the page fault.
2) Copy from user code retries a copy in byte-at-time mode to check
whether any additional bytes can be copied.
On the other side of the fence are some bad drivers that do not check
the return value from individual get_user() calls and may access
multiple user addresses without noticing that some/all calls have
failed.
Fix by adding a counter (current->mce_count) to keep track of repeated
machine checks before task_work() is called. First machine check saves
the address information and calls task_work_add(). Subsequent machine
checks before that task_work call back is executed check that the address
is in the same page as the first machine check (since the callback will
offline exactly one page).
Expected worst case is four machine checks before moving on (e.g. one
user access with page faults disabled, then a repeat to the same address
with page faults enabled ... repeat in copy tail bytes). Just in case
there is some code that loops forever enforce a limit of 10.
[ bp: Massage commit message, drop noinstr, fix typo, extend panic
messages. ]
Fixes: 5567d11c21 ("x86/mce: Send #MC singal from task work")
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/YT/IJ9ziLqmtqEPu@agluck-desk2.amr.corp.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0341d5e3d1 ]
The cur_tx counter must be incremented after TACT bit of
txdesc->status was set. However, a CPU is possible to reorder
instructions and/or memory accesses between cur_tx and
txdesc->status. And then, if TX interrupt happened at such a
timing, the sh_eth_tx_free() may free the descriptor wrongly.
So, add wmb() before cur_tx++.
Otherwise NETDEV WATCHDOG timeout is possible to happen.
Fixes: 86a74ff21a ("net: sh_eth: add support for Renesas SuperH Ethernet")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdff1eda69 ]
One MIPS platform (mach-rc32434) defines GPIOBASE. This macro
conflicts with one of the same name in lpc_sch.c. Rename the latter one
to prevent the build error.
../drivers/mfd/lpc_sch.c:25: error: "GPIOBASE" redefined [-Werror]
25 | #define GPIOBASE 0x44
../arch/mips/include/asm/mach-rc32434/rb.h:32: note: this is the location of the previous definition
32 | #define GPIOBASE 0x050000
Cc: Denis Turischev <denis@compulab.co.il>
Fixes: e82c60ae7d ("mfd: Introduce lpc_sch for Intel SCH LPC bridge")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 922e8ce883 ]
The IRQ support for SCH GPIO is not specific to the Intel Quark SoC.
Moreover the IRQ routing is quite interesting there, so while it's
needs a special support, the driver haven't it anyway yet.
Due to above remove basically redundant code of IRQ support.
This reverts commit ec689a8a81.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b2b918319 ]
If error recovery is already enabled, bnxt_timer() will periodically
check the heartbeat register and the reset counter. If we get an
error recovery async. notification from the firmware (e.g. change in
primary/secondary role), we will immediately read and update the
heartbeat register and the reset counter. If the timer for the next
health check expires soon after this, we may read the heartbeat register
again in quick succession and find that it hasn't changed. This will
trigger error recovery unintentionally.
The likelihood is small because we also reset fw_health->tmr_counter
which will reset the interval for the next health check. But the
update is not protected and bnxt_timer() can miss the update and
perform the health check without waiting for the full interval.
Fix it by only reading the heartbeat register and reset counter in
bnxt_async_event_process() if error recovery is trasitioning to the
enabled state. Also add proper memory barriers so that when enabling
for the first time, bnxt_timer() will see the tmr_counter interval and
perform the health check after the full interval has elapsed.
Fixes: 7e914027f7 ("bnxt_en: Enable health monitoring.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4d95c3c19 ]
We currently only log the error recovery settings if it is enabled.
In some cases, firmware disables error recovery after it was
initially enabled. Without logging anything, the user will not be
aware of this change in setting.
Log it when error recovery is disabled. Also, change the reset count
value from hexadecimal to decimal.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a44daa8fcb ]
Firmware is capable of generating asynchronous debug notifications.
The event data is opaque to the driver and is simply logged. Debug
notifications can be enabled by turning on hardware status messages
using the ethtool msglvl interface.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6fdab8a3ad ]
The current asic.rev is incomplete and does not include the metal
revision. Add the metal revision and decode the complete asic
revision into the more common and readable form (A0, B0, etc).
Fixes: 7154917a12 ("bnxt_en: Refactor bnxt_dl_info_get().")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63f8428b40 ]
Broadcom's b53 switches have one IMP (Inband Management Port) that needs
to be programmed using its own designed register. IMP port may be
different than CPU port - especially on devices with multiple CPU ports.
For that reason it's required to explicitly note IMP port index and
check for it when choosing a register to use.
This commit fixes BCM5301x support. Those switches use CPU port 5 while
their IMP port is 8. Before this patch b53 was trying to program port 5
with B53_PORT_OVERRIDE_CTRL instead of B53_GMII_PORT_OVERRIDE_CTRL(5).
It may be possible to also replace "cpu_port" usages with
dsa_is_cpu_port() but that is out of the scope of thix BCM5301x fix.
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a0ed250f9 ]
The GRE tunnel device can pull existing outer headers in ipge_xmit.
This is a rare path, apparently unique to this device. The below
commit ensured that pulling does not move skb->data beyond csum_start.
But it has a false positive if ip_summed is not CHECKSUM_PARTIAL and
thus csum_start is irrelevant.
Refine to exclude this. At the same time simplify and strengthen the
test.
Simplify, by moving the check next to the offending pull, making it
more self documenting and removing an unnecessary branch from other
code paths.
Strengthen, by also ensuring that the transport header is correct and
therefore the inner headers will be after skb_reset_inner_headers.
The transport header is set to csum_start in skb_partial_csum_set.
Link: https://lore.kernel.org/netdev/YS+h%2FtqCJJiQei+W@shredder/
Fixes: 1d011c4803 ("ip_gre: add validation for csum_start")
Reported-by: Ido Schimmel <idosch@idosch.org>
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ddbc2a00d ]
Previous commit 68233c583a removes the qlcnic_rom_lock()
in qlcnic_pinit_from_rom(), but remains its corresponding
unlock function, which is odd. I'm not very sure whether the
lock is missing, or the unlock is redundant. This bug is
suggested by a static analysis tool, please advise.
Fixes: 68233c583a ("qlcnic: updated reset sequence")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7c5e6ff53 ]
syzbot found that forcing a big quantum attribute would crash hosts fast,
essentially using this:
tc qd replace dev eth0 root fq_codel quantum 4294967295
This is because fq_codel_dequeue() would have to loop
~2^31 times in :
if (flow->deficit <= 0) {
flow->deficit += q->quantum;
list_move_tail(&flow->flowchain, &q->old_flows);
goto begin;
}
SFQ max quantum is 2^19 (half a megabyte)
Lets adopt a max quantum of one megabyte for FQ_CODEL.
Fixes: 4b549a2ef4 ("fq_codel: Fair Queue Codel AQM")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 730affed24 ]
Bug reported by KASAN:
BUG: KASAN: use-after-scope in inet6_ehashfn (net/ipv6/inet6_hashtables.c:40)
Call Trace:
(...)
inet6_ehashfn (net/ipv6/inet6_hashtables.c:40)
(...)
nf_sk_lookup_slow_v6 (net/ipv6/netfilter/nf_socket_ipv6.c:91
net/ipv6/netfilter/nf_socket_ipv6.c:146)
It seems that this bug has already been fixed by Eric Dumazet in the
past in:
commit 78296c97ca ("netfilter: xt_socket: fix a stack corruption bug")
But a variant of the same issue has been introduced in
commit d64d80a2cd ("netfilter: x_tables: don't extract flow keys on early demuxed sks in socket match")
`daddr` and `saddr` potentially hold a reference to ipv6_var that is no
longer in scope when the call to `nf_socket_get_sock_v6` is made.
Fixes: d64d80a2cd ("netfilter: x_tables: don't extract flow keys on early demuxed sks in socket match")
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Benjamin Hesmans <benjamin.hesmans@tessares.net>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d12e1c4649 ]
Setting DSA_MAX_PORTS caused DSA to call b53 callbacks (e.g.
b53_disable_port() during dsa_register_switch()) for invalid
(non-existent) ports. That made b53 modify unrelated registers and is
one of reasons for a broken BCM5301x support.
This problem exists for years but DSA_MAX_PORTS usage has changed few
times. It seems the most accurate to reference commit dropping
dsa_switch_alloc() in the Fixes tag.
Fixes: 7e99e34701 ("net: dsa: remove dsa_switch_alloc helper")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdb067d31c ]
It isn't true that CPU port is always the last one. Switches BCM5301x
have 9 ports (port 6 being inactive) and they use port 5 as CPU by
default (depending on design some other may be CPU ports too).
A more reliable way of determining number of ports is to check for the
last set bit in the "enabled_ports" bitfield.
This fixes b53 internal state, it will allow providing accurate info to
the DSA and is required to fix BCM5301x support.
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ecdc28defc ]
If the network devices connected to the system beyond
HSO_MAX_NET_DEVICES. add_net_device() in hso_create_net_device()
will be failed for the network_table is full. It will lead to
business failure which rely on network_table, for example,
hso_suspend() and hso_resume(). It will also lead to memory leak
because resource release process can not search the hso_device
object from network_table in hso_free_interface().
Add failure handler for add_net_device() in hso_create_net_device()
to solve the above problems.
Fixes: 72dc1c096c ("HSO: add option hso driver")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfd862a7e9 ]
'$cin' and '$sin' variables are local to a function: they are then not
available from the cleanup trap.
Instead, we need to use '$large' and '$small' that are not local and
defined just before setting the trap.
Without this patch, running this script in a loop might cause a:
write: No space left on device
issue.
Fixes: 1a418cb8e8 ("mptcp: simult flow self-tests")
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e90dfa7a8 ]
I noticed that only port 0 worked on the RTL8366RB since we
started to use custom tags.
It turns out that the format of egress custom tags is actually
different from ingress custom tags. While the lower bits just
contain the port number in ingress tags, egress tags need to
indicate destination port by setting the bit for the
corresponding port.
It was working on port 0 because port 0 added 0x00 as port
number in the lower bits, and if you do this the packet appears
at all ports, including the intended port. Ooops.
Fix this and all ports work again. Use the define for shifting
the "type A" into place while we're at it.
Tested on the D-Link DIR-685 by sending traffic to each of
the ports in turn. It works.
Fixes: 86dd9868b8 ("net: dsa: tag_rtl4_a: Support also egress tags")
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 889a1b3f35 ]
If an error occurs after a 'gpiochip_add_data()' call it must be undone by
a corresponding 'gpiochip_remove()' as already done in the remove function.
To simplify the code a fix a leak in the error handling path of the probe,
use the managed version instead (i.e. 'devm_gpiochip_add_data()')
Fixes: 698b8eeaed ("gpio/mpc8xxx: change irq handler from chained to normal")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 555bda42b0 ]
Commit 698b8eeaed ("gpio/mpc8xxx: change irq handler from chained to normal")
has introduced a new 'goto err;' at the very end of the function, but has
not updated the error handling path accordingly.
Add the now missing 'irq_domain_remove()' call which balances a previous
'irq_domain_create_linear() call.
Fixes: 698b8eeaed ("gpio/mpc8xxx: change irq handler from chained to normal")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit edf7b4a2d8 ]
The build on fedora:35 and fedora:rawhide with clang is failing with:
49 41.00 fedora:35 : FAIL clang version 13.0.0 (Fedora 13.0.0~rc1-1.fc35)
bench/inject-buildid.c:351:6: error: variable 'len' set but not used [-Werror,-Wunused-but-set-variable]
u64 len = 0;
^
1 error generated.
make[3]: *** [/git/perf-5.14.0-rc7/tools/build/Makefile.build:139: bench] Error 2
50 41.11 fedora:rawhide : FAIL clang version 13.0.0 (Fedora 13.0.0~rc1-1.fc35)
bench/inject-buildid.c:351:6: error: variable 'len' set but not used [-Werror,-Wunused-but-set-variable]
u64 len = 0;
^
1 error generated.
make[3]: *** [/git/perf-5.14.0-rc7/tools/build/Makefile.build:139: bench] Error 2
That 'len' variable is not used at all, so just make sure all the
synthesize_RECORD() routines return ssize_t to propagate the writen()
return, as it may fail, ditch the 'ret' var and bail out if those
routines fail.
Fixes: 0bf02a0d80 ("perf bench: Add build-id injection benchmark")
Acked-by: Namhyung Kim <namhyung@kernel.org>
Link: http://lore.kernel.org/lkml/CAM9d7cgEZNSor+B+7Y2C+QYGme_v5aH0Zn0RLfxoQ+Fy83EHrg@mail.gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b5ff0405e ]
0day bot reports a build error:
ERROR: modpost: "clear_user_page" [drivers/media/v4l2-core/videobuf-dma-sg.ko] undefined!
so export it in arch/arc/ to fix the build error.
In most ARCHes, clear_user_page() is a macro. OTOH, in a few
ARCHes it is a function and needs to be exported.
PowerPC exported it in 2004. It looks like nds32 and nios2
still need to have it exported.
Fixes: 4102b53392 ("ARC: [mm] Aliasing VIPT dcache support 2/4")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-snps-arc@lists.infradead.org
Signed-off-by: Vineet Gupta <vgupta@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6826c6849b ]
The CPU_ON PSCI call takes a payload that KVM uses to configure a
destination vCPU to run. This payload is non-architectural state and not
exposed through any existing UAPI. Effectively, we have a race between
CPU_ON and userspace saving/restoring a guest: if the target vCPU isn't
ran again before the VMM saves its state, the requested PC and context
ID are lost. When restored, the target vCPU will be runnable and start
executing at its old PC.
We can avoid this race by making sure the reset payload is serviced
before userspace can access a vCPU's state.
Fixes: 358b28f09f ("arm/arm64: KVM: Allow a VCPU to fully reset itself")
Signed-off-by: Oliver Upton <oupton@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210818202133.1106786-3-oupton@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6654f9dfcb ]
KVM correctly serializes writes to a vCPU's reset state, however since
we do not take the KVM lock on the read side it is entirely possible to
read state from two different reset requests.
Cure the race for now by taking the KVM lock when reading the
reset_state structure.
Fixes: 358b28f09f ("arm/arm64: KVM: Allow a VCPU to fully reset itself")
Signed-off-by: Oliver Upton <oupton@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210818202133.1106786-2-oupton@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a89d69a44e ]
Since 2431c4f5b4 ("mtd: Implement mtd_{read,write}() as wrappers
around mtd_{read,write}_oob()") don't allow _write|_read and
_write_oob|_read_oob existing at the same time, we should check the
existence of callbacks "_read and _write" from subdev's master device
(We can trust master device since it has been registered) before
assigning, otherwise following warning occurs while making
concatenated device:
WARNING: CPU: 2 PID: 6728 at drivers/mtd/mtdcore.c:595
add_mtd_device+0x7f/0x7b0
Fixes: 2431c4f5b4 ("mtd: Implement mtd_{read,write}() around ...")
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210817114857.2784825-3-chengzhihao1@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a946506c48 ]
The driver was registering IRQ 0 when no IRQ was set. This leads to
warnings with newer kernels.
Clear the resource flags, so no resource is registered at all in this
case.
Fixes: 2f17dd34ff ("mfd: tqmx86: IO controller with I2C, Wachdog and GPIO")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3245a7b7b ]
Syzbot hit use-after-free in nf_tables_dump_sets. The problem was in
missing lock protection for nft_ct_pcpu_template_refcnt.
Before commit f102d66b33 ("netfilter: nf_tables: use dedicated
mutex to guard transactions") all transactions were serialized by global
mutex, but then global mutex was changed to local per netnamespace
commit_mutex.
This change causes use-after-free bug, when 2 netnamespaces concurently
changing nft_ct_pcpu_template_refcnt without proper locking. Fix it by
adding nft_ct_pcpu_mutex and protect all nft_ct_pcpu_template_refcnt
changes with it.
Fixes: f102d66b33 ("netfilter: nf_tables: use dedicated mutex to guard transactions")
Reported-and-tested-by: syzbot+649e339fa6658ee623d3@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit daa3736151 ]
Remove interrupt disablement during backlight setting. It is
way to dangerous and makes platforms instable by having it
miss vblank IRQs leading to the graphics derailing.
The code is using ndelay() which is not available on
platforms such as ARM and will result in 32 * udelay(1)
which is substantial.
Add some code to detect if an interrupt occurs during the
tight loop and in that case just redo it from the top.
Fixes: 5317f37e48 ("backlight: Add Kinetic KTD253 backlight driver")
Cc: Stephan Gerhold <stephan@gerhold.net>
Reported-by: newbyte@disroot.org
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f949a9ebce ]
On Cherry Trail devices with an AXP288 PMIC the external SD-card slot
used the AXP's DLDO2 as card-voltage and either DLDO3 or GPIO1LDO
(GPIO1 pin in low noise LDO mode) as signal-voltage.
These regulators are turned on/off and in case of the signal-voltage
also have their output-voltage changed by the _PS0 and _PS3 power-
management ACPI methods on the MMC-controllers ACPI fwnode as well as
by the _DSM ACPI method for changing the signal voltage.
The AML code implementing these methods is directly accessing the
PMIC through ACPI I2C OpRegion accesses, instead of using the special
PMIC OpRegion handled by drivers/acpi/pmic/intel_pmic_xpower.c .
This means that the contents of the involved PMIC registers can change
without the change being made through the regmap interface, so regmap
should not cache the contents of these registers.
Mark the regulator power on/off, the regulator voltage control and the
GPIO1 control registers as volatile, to avoid regmap caching them.
Specifically this fixes an issue on some models where the i915 driver
toggles another LDO using the same on/off register on/off through
MIPI sequences (through intel_soc_pmic_exec_mipi_pmic_seq_element())
which then writes back a cached on/off register-value where the
card-voltage is off causing the external sdcard slot to stop working
when the screen goes blank, or comes back on again.
The regulator register-range now marked volatile also includes the
buck regulator control registers. This is done on purpose these are
normally not touched by the AML code, but they are updated directly
by the SoC's PUNIT which means that they may also change without going
through regmap.
Note the AXP288 PMIC is only used on Bay- and Cherry-Trail platforms,
so even though this is an ACPI specific problem there is no need to
make the new volatile ranges conditional since these platforms always
use ACPI.
Fixes: dc91c3b6fe ("mfd: axp20x: Mark AXP20X_VBUS_IPSOUT_MGMT as volatile")
Fixes: cd53216625 ("mfd: axp20x: Fix axp288 volatile ranges")
Reported-and-tested-by: Clamshell <clamfly@163.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1511df6f5e upstream.
EMIT6_PCREL() macro assumes that the previous pass generated 6 bytes
of code, which is not the case if branch shortening took place. Fix by
using jit->prg, like all the other EMIT6_PCREL_*() macros.
Reported-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Fixes: 4e9b4a6883 ("s390/bpf: Use relative long branches")
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e61dc9da0 upstream.
The JIT uses agfi for subtracting constants, but -(-0x80000000) cannot
be represented as a 32-bit signed binary integer. Fix by using algfi in
this particular case.
Reported-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Fixes: 0546231057 ("s390/bpf: Add s390x eBPF JIT compiler backend")
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db7bee6538 upstream.
Currently the JIT completely removes things like `reg32 += 0`,
however, the BPF_ALU semantics requires the target register to be
zero-extended in such cases.
Fix by optimizing out only the arithmetic operation, but not the
subsequent zero-extension.
Reported-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Fixes: 0546231057 ("s390/bpf: Add s390x eBPF JIT compiler backend")
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0097ae5f7a ]
When the function IS_ALIGNED() returns false, the value of ret is 0.
So, we set ret to -EINVAL to indicate this error.
Clean up smatch warning:
drivers/ntb/test/ntb_perf.c:602 perf_setup_inbuf() warn: missing error
code 'ret'.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 319f83ac98 ]
When the value of nm->isr_ctx is false, the value of ret is 0.
So, we set ret to -ENOMEM to indicate this error.
Clean up smatch warning:
drivers/ntb/test/ntb_msi_test.c:373 ntb_msit_probe() warn: missing
error code 'ret'.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7db8263a12 ]
When adapter->registered_device_map is NULL, the value of err is
uncertain, we set err to -EINVAL to avoid ambiguity.
Clean up smatch warning:
drivers/net/ethernet/chelsio/cxgb/cxgb2.c:1114 init_one() warn: missing
error code 'err'
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d52c58b9c ]
The function bfq_setup_merge prepares the merging between two
bfq_queues, say bfqq and new_bfqq. To this goal, it assigns
bfqq->new_bfqq = new_bfqq. Then, each time some I/O for bfqq arrives,
the process that generated that I/O is disassociated from bfqq and
associated with new_bfqq (merging is actually a redirection). In this
respect, bfq_setup_merge increases new_bfqq->ref in advance, adding
the number of processes that are expected to be associated with
new_bfqq.
Unfortunately, the stable-merging mechanism interferes with this
setup. After bfqq->new_bfqq has been set by bfq_setup_merge, and
before all the expected processes have been associated with
bfqq->new_bfqq, bfqq may happen to be stably merged with a different
queue than the current bfqq->new_bfqq. In this case, bfqq->new_bfqq
gets changed. So, some of the processes that have been already
accounted for in the ref counter of the previous new_bfqq will not be
associated with that queue. This creates an unbalance, because those
references will never be decremented.
This commit fixes this issue by reestablishing the previous, natural
behaviour: once bfqq->new_bfqq has been set, it will not be changed
until all expected redirections have occurred.
Signed-off-by: Davide Zini <davidezini2@gmail.com>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Link: https://lore.kernel.org/r/20210802141352.74353-2-paolo.valente@linaro.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aabbdc67f3 ]
Add quirk CDC_MBIM_FLAG_AVOID_ALTSETTING_TOGGLE for Telit LN920
0x1061 composition in order to avoid bind error.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21274aa178 ]
Check one more time before exiting the API with an error.
Fix API to poll at least twice, in case there are other high priority
tasks and this API doesn't get CPU cycles for multiple jiffies update.
In addition, increase timeout from usecs_to_jiffies(10000) to
usecs_to_jiffies(20000), to prevent the case that for CONFIG_100HZ
timeout will be a single jiffies.
A single jiffies results actual timeout that can be any time between
1usec and 10msec. To solve this, a value of usecs_to_jiffies(20000)
ensures that timeout is 2 jiffies.
Signed-off-by: Smadar Fuks <smadarf@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dbe80cf471 ]
We must not pet a running watchdog when handle_boot_enabled is off
because this will kick off automatic triggering before userland is
running, defeating the purpose of the handle_boot_enabled control.
Furthermore, don't ping in case watchdog_set_last_hw_keepalive was
called incorrectly when the hardware watchdog is actually not running.
Fixed: cef9572e9a ("watchdog: add support for adjusting last known HW keepalive time")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/93d56386-6e37-060b-55ce-84de8cde535f@web.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 32837d8a8f ]
Some Cavium endpoints are implemented as multi-function devices without ACS
capability, but they actually don't support peer-to-peer transactions.
Add ACS quirks to declare DMA isolation for the following devices:
- BGX device found on Octeon-TX (8xxx)
- CGX device found on Octeon-TX2 (9xxx)
- RPM device found on Octeon-TX3 (10xxx)
Link: https://lore.kernel.org/r/20210810122425.1115156-1-george.cherian@marvell.com
Signed-off-by: George Cherian <george.cherian@marvell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1de58802f ]
J7200 has the same PCIe IP as in J721E with minor changes in the
wrapper. J7200 allows byte access of bridge configuration space
registers and the register field for LINK_DOWN interrupt is different.
J7200 also requires "quirk_detect_quiet_flag" to be set. Configure these
changes as part of driver data applicable only to J7200.
Link: https://lore.kernel.org/r/20210811123336.31357-4-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09c24094b2 ]
PCIe fails to link up if SERDES lanes not used by PCIe are assigned to
another protocol. For example, link training fails if lanes 2 and 3 are
assigned to another protocol while lanes 0 and 1 are used for PCIe to
form a two lane link. This failure is due to an incorrect tie-off on an
internal status signal indicating electrical idle.
Status signals going from SERDES to PCIe Controller are tied-off when a
lane is not assigned to PCIe. Signal indicating electrical idle is
incorrectly tied-off to a state that indicates non-idle. As a result,
PCIe sees unused lanes to be out of electrical idle and this causes
LTSSM to exit Detect.Quiet state without waiting for 12ms timeout to
occur. If a receiver is not detected on the first receiver detection
attempt in Detect.Active state, LTSSM goes back to Detect.Quiet and
again moves forward to Detect.Active state without waiting for 12ms as
required by PCIe base specification. Since wait time in Detect.Quiet is
skipped, multiple receiver detect operations are performed back-to-back
without allowing time for capacitance on the transmit lines to
discharge. This causes subsequent receiver detection to always fail even
if a receiver gets connected eventually.
Add a quirk flag "quirk_detect_quiet_flag" to program the minimum
time the LTSSM should wait on entering Detect.Quiet state here.
This has to be set for J7200 as it has an incorrect tie-off on unused
lanes.
Link: https://lore.kernel.org/r/20210811123336.31357-3-kishon@ti.com
Signed-off-by: Nadeem Athani <nadeem@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e242060c6 ]
Since kprobe_events and uprobe_events only check whether the
other same-type probe event has the same name or not, if the
user gives the same name of the existing tracepoint event (or
the other type of probe events), it silently fails to create
the tracefs entry (but registered.) as below.
/sys/kernel/tracing # ls events/task/task_rename
enable filter format hist id trigger
/sys/kernel/tracing # echo p:task/task_rename vfs_read >> kprobe_events
[ 113.048508] Could not create tracefs 'task_rename' directory
/sys/kernel/tracing # cat kprobe_events
p:task/task_rename vfs_read
To fix this issue, check whether the existing events have the
same name or not in trace_probe_register_event_call(). If exists,
it rejects to register the new event.
Link: https://lkml.kernel.org/r/162936876189.187130.17558311387542061930.stgit@devnote2
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ff80e2de3 ]
Although irq_create_mapping() is able to deal with duplicate
mappings, it really isn't supposed to be a substitute for
irq_find_mapping(), and can result in allocations that take place
in atomic context if the mapping didn't exist.
Fix the handful of MFD drivers that use irq_create_mapping() in
interrupt context by using irq_find_mapping() instead.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1e71c1688 ]
There is a potential race between fuse_read_interrupt() and
fuse_request_end().
TASK1
in fuse_read_interrupt(): delete req->intr_entry (while holding
fiq->lock)
TASK2
in fuse_request_end(): req->intr_entry is empty -> skip fiq->lock
wake up TASK3
TASK3
request is freed
TASK1
in fuse_read_interrupt(): dereference req->in.h.unique ***BAM***
Fix by always grabbing fiq->lock if the request was ever interrupted
(FR_INTERRUPTED set) thereby serializing with concurrent
fuse_read_interrupt() calls.
FR_INTERRUPTED is set before the request is queued on fiq->interrupts.
Dequeing the request is done with list_del_init() but FR_INTERRUPTED is not
cleared in this case.
Reported-by: lijiazi <lijiazi@xiaomi.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec343111c0 ]
These are the actual frequencies reported by the PLL, so let's
report these. The roundoffs are inappropriate, we should round
to the frequency that the clock will later report.
Drop some whitespace at the same time.
Cc: phone-devel@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 427900d27d upstream.
Currently, the VF does not clear the interrupt source immediately after
receiving the interrupt. As a result, if the second interrupt task is
triggered when processing the first interrupt task, clearing the
interrupt source before exiting will clear the interrupt sources of the
two tasks at the same time. As a result, no interrupt is triggered for
the second task. The VF detects the missed message only when the next
interrupt is generated.
Clearing it immediately after executing check_evt_cause ensures that:
1. Even if two interrupt tasks are triggered at the same time, they can
be processed.
2. If the second task is triggered during the processing of the first
task and the interrupt source is not cleared, the interrupt is reported
after vector0 is enabled.
Fixes: b90fcc5bd9 ("net: hns3: add reset handling for VF when doing Core/Global/IMP reset")
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b81d894874 upstream.
The firmware will not disable mac in flr process. Therefore, the driver
needs to proactively disable mac during flr, which is the same as the
function reset.
Fixes: 35d93a3004 ("net: hns3: adjust the process of PF reset")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1dc839ec09 upstream.
Currently, affinity_mask is set to a single cpu. As a result,
irqbalance becomes invalid in SUBSET or EXACT mode. To solve
this problem, change affinity_mask to numa node range. In this
way, irqbalance can be performed on the cpu of the numa node.
Fixes: 0812545487 ("net: hns3: add interrupt affinity support for misc interrupt")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d18e81183b upstream.
The hardware cannot handle short tunnel frames below 65 bytes,
and will cause vlan tag missing problem. So pads packet size to
65 bytes for tunnel frames to fix this bug.
Fixes: 3db084d28dc0("net: hns3: Fix for vxlan tx checksum bug")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1affc01fdc upstream.
The call to bnxt_free_mem(..., false) in the bnxt_half_open_nic() error
path will deallocate ring descriptor memory via bnxt_free_?x_rings(),
but because irq_re_init is false, the ring info itself is not freed.
To simplify error paths, deallocation functions have generally been
written to be safe when called on unallocated memory. It should always
be safe to call dev_close(), which calls bnxt_free_skbs() a second time,
even in this semi- allocated ring state.
Calling bnxt_free_skbs() a second time with the rings already freed will
cause NULL pointer dereference. Fix it by checking the rings are valid
before proceeding in bnxt_free_tx_skbs() and
bnxt_free_one_rx_ring_skbs().
Fixes: 975bc99a4a ("bnxt_en: Refactor bnxt_free_rx_skbs().")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 267cdfa213 upstream.
POWER9 DD2.2 and 2.3 hardware implements a "fake-suspend" mode where
certain TM instructions executed in HV=0 mode cause softpatch interrupts
so the hypervisor can emulate them and prevent problematic processor
conditions. In this fake-suspend mode, the treclaim. instruction does
not modify registers.
Unfortunately the rfscv instruction executed by the guest do not
generate softpatch interrupts, which can cause the hypervisor to lose
track of the fake-suspend mode, and it can execute this treclaim. while
not in fake-suspend mode. This modifies GPRs and crashes the hypervisor.
It's not trivial to disable scv in the guest with HFSCR now, because
they assume a POWER9 has scv available. So this fix saves and restores
checkpointed registers across the treclaim.
Fixes: 7854f7545b ("KVM: PPC: Book3S: Rework TM save/restore code and make it C-callable")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210908101718.118522-2-npiggin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 273c29e944 upstream.
If a failover occurs before a login response is received, the login
response buffer maybe undefined. Check that there was no failover
before accessing the login response buffer.
Fixes: 032c5e8284 ("Driver for IBM System i/p VNIC protocol")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e50e711351 upstream.
Turn udp_tunnel_nic work-queue to an ordered work-queue. This queue
holds the UDP-tunnel configuration commands of the different netdevs.
When the netdevs are functions of the same NIC the order of
execution may be crucial.
Problem example:
NIC with 2 PFs, both PFs declare offload quota of up to 3 UDP-ports.
$ifconfig eth2 1.1.1.1/16 up
$ip link add eth2_19503 type vxlan id 5049 remote 1.1.1.2 dev eth2 dstport 19053
$ip link set dev eth2_19503 up
$ip link add eth2_19504 type vxlan id 5049 remote 1.1.1.3 dev eth2 dstport 19054
$ip link set dev eth2_19504 up
$ip link add eth2_19505 type vxlan id 5049 remote 1.1.1.4 dev eth2 dstport 19055
$ip link set dev eth2_19505 up
$ip link add eth2_19506 type vxlan id 5049 remote 1.1.1.5 dev eth2 dstport 19056
$ip link set dev eth2_19506 up
NIC RX port offload infrastructure offloads the first 3 UDP-ports (on
all devices which sets NETIF_F_RX_UDP_TUNNEL_PORT feature) and not
UDP-port 19056. So both PFs gets this offload configuration.
$ip link set dev eth2_19504 down
This triggers udp-tunnel-core to remove the UDP-port 19504 from
offload-ports-list and offload UDP-port 19056 instead.
In this scenario it is important that the UDP-port of 19504 will be
removed from both PFs before trying to add UDP-port 19056. The NIC can
stop offloading a UDP-port only when all references are removed.
Otherwise the NIC may report exceeding of the offload quota.
Fixes: cc4e3835ef ("udp_tunnel: add central NIC RX port offload infrastructure")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 20e100f527 upstream.
Handle MFW (management FW) error response in order to avoid a crash
during recovery flows.
Changes from v1:
- Add "Fixes tag".
Fixes: tag 5e7ba042fd ("qed: Fix reading stale configuration information")
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b704b27be upstream.
If altname deletion of the short alternative name fails, the error
message printed is: "Failed to add short alternative name".
This is obviously a typo, as we are testing altname deletion.
Fix this using a proper error message.
Fixes: f95e6c9c46 ("selftest: net: add alternative names test")
Signed-off-by: Andrea Claudi <aclaudi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f884f3962 upstream.
Commit 10d3be5692 ("tcp-tso: do not split TSO packets at retransmit
time") may directly retrans a multiple segments TSO/GSO packet without
split, Since this commit, we can no longer assume that a retransmitted
packet is a single segment.
This patch fixes the tp->undo_retrans accounting in tcp_sacktag_one()
that use the actual segments(pcount) of the retransmitted packet.
Before that commit (10d3be5692), the assumption underlying the
tp->undo_retrans-- seems correct.
Fixes: 10d3be5692 ("tcp-tso: do not split TSO packets at retransmit time")
Signed-off-by: zhenggy <zhenggy@chinatelecom.cn>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a69ae291e1 upstream.
Commit 865c50e1d2 ("x86/uaccess: utilize CONFIG_CC_HAS_ASM_GOTO_OUTPUT")
added an optimised version of __get_user_asm() for x86 using 'asm goto'.
Like the non-optimised code, the 32-bit implementation of 64-bit
get_user() expands to a pair of 32-bit accesses. Unlike the
non-optimised code, the _original_ pointer is incremented to copy the
high word instead of loading through a new pointer explicitly
constructed to point at a 32-bit type. Consequently, if the pointer
points at a 64-bit type then we end up loading the wrong data for the
upper 32-bits.
This was observed as a mount() failure in Android targeting i686 after
b0cfcdd9b9 ("d_path: make 'prepend()' fill up the buffer exactly on
overflow") because the call to copy_from_kernel_nofault() from
prepend_copy() ends up in __get_kernel_nofault() and casts the source
pointer to a 'u64 __user *'. An attempt to mount at "/debug_ramdisk"
therefore ends up failing trying to mount "/debumdismdisk".
Use the existing '__gu_ptr' source pointer to unsigned int for 32-bit
__get_user_asm_u64() instead of the original pointer.
Cc: Bill Wendling <morbo@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 865c50e1d2 ("x86/uaccess: utilize CONFIG_CC_HAS_ASM_GOTO_OUTPUT")
Signed-off-by: Will Deacon <will@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6a52e73368 upstream.
DSA supports connecting to a phy-handle, and has a fallback to a non-OF
based method of connecting to an internal PHY on the switch's own MDIO
bus, if no phy-handle and no fixed-link nodes were present.
The -ENODEV error code from the first attempt (phylink_of_phy_connect)
is what triggers the second attempt (phylink_connect_phy).
However, when the first attempt returns a different error code than
-ENODEV, this results in an unbalance of calls to phylink_create and
phylink_destroy by the time we exit the function. The phylink instance
has leaked.
There are many other error codes that can be returned by
phylink_of_phy_connect. For example, phylink_validate returns -EINVAL.
So this is a practical issue too.
Fixes: aab9c4067d ("net: dsa: Plug in PHYLINK support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20210914134331.2303380-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04f08eb44b upstream.
syzbot reported another data-race in af_unix [1]
Lets change __skb_insert() to use WRITE_ONCE() when changing
skb head qlen.
Also, change unix_dgram_poll() to use lockless version
of unix_recvq_full()
It is verry possible we can switch all/most unix_recvq_full()
to the lockless version, this will be done in a future kernel version.
[1] HEAD commit: 8596e589b7
BUG: KCSAN: data-race in skb_queue_tail / unix_dgram_poll
write to 0xffff88814eeb24e0 of 4 bytes by task 25815 on cpu 0:
__skb_insert include/linux/skbuff.h:1938 [inline]
__skb_queue_before include/linux/skbuff.h:2043 [inline]
__skb_queue_tail include/linux/skbuff.h:2076 [inline]
skb_queue_tail+0x80/0xa0 net/core/skbuff.c:3264
unix_dgram_sendmsg+0xff2/0x1600 net/unix/af_unix.c:1850
sock_sendmsg_nosec net/socket.c:703 [inline]
sock_sendmsg net/socket.c:723 [inline]
____sys_sendmsg+0x360/0x4d0 net/socket.c:2392
___sys_sendmsg net/socket.c:2446 [inline]
__sys_sendmmsg+0x315/0x4b0 net/socket.c:2532
__do_sys_sendmmsg net/socket.c:2561 [inline]
__se_sys_sendmmsg net/socket.c:2558 [inline]
__x64_sys_sendmmsg+0x53/0x60 net/socket.c:2558
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffff88814eeb24e0 of 4 bytes by task 25834 on cpu 1:
skb_queue_len include/linux/skbuff.h:1869 [inline]
unix_recvq_full net/unix/af_unix.c:194 [inline]
unix_dgram_poll+0x2bc/0x3e0 net/unix/af_unix.c:2777
sock_poll+0x23e/0x260 net/socket.c:1288
vfs_poll include/linux/poll.h:90 [inline]
ep_item_poll fs/eventpoll.c:846 [inline]
ep_send_events fs/eventpoll.c:1683 [inline]
ep_poll fs/eventpoll.c:1798 [inline]
do_epoll_wait+0x6ad/0xf00 fs/eventpoll.c:2226
__do_sys_epoll_wait fs/eventpoll.c:2238 [inline]
__se_sys_epoll_wait fs/eventpoll.c:2233 [inline]
__x64_sys_epoll_wait+0xf6/0x120 fs/eventpoll.c:2233
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0x0000001b -> 0x00000001
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 25834 Comm: syz-executor.1 Tainted: G W 5.14.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 86b18aaa2b ("skbuff: fix a data race in skb_queue_len()")
Cc: Qian Cai <cai@lca.pw>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c4cea8fa7 upstream.
If the sendmsg() call in vhost_tx_batch() fails, both the 'batched_xdp'
and 'done_idx' indexes are left unchanged. If such failure happens
when batched_xdp == VHOST_NET_BATCH, the next call to
vhost_net_build_xdp() will access and write memory outside the xdp
buffers area.
Since sendmsg() can only error with EBADFD, this change addresses the
issue explicitly freeing the XDP buffers batch on error.
Fixes: 0a0be13b8f ("vhost_net: batch submitting XDP buffers to underlayer sockets")
Suggested-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec783c7cb2 upstream.
We need to import the 'sys' package since the script has called
sys.exit() method.
Fixes: 6ad7cbc015 ("Makefile: Add clang-tidy and static analyzer support to makefile")
Signed-off-by: Kortan <kortanzh@gmail.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5c102238c upstream.
There is an off-by-one problem in ipa_table_init_add(), when
initializing filter tables.
In that function, the number of filter table entries is determined
based on the number of set bits in the filter map. However that
count does *not* include the extra "slot" in the filter table that
holds the filter map itself. Meanwhile, ipa_table_addr() *does*
include the filter map in the memory it returns, but because the
count it's provided doesn't include it, it includes one too few
table entries.
Fix this by including the extra slot for the filter map in the count
computed in ipa_table_init_add().
Note: ipa_filter_reset_table() does not have this problem; it resets
filter table entries one by one, but does not overwrite the filter
bitmap.
Fixes: 2b9feef2b6 ("soc: qcom: ipa: filter and routing tables")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b89a05b21f upstream.
In perf_event_addr_filters_apply, the task associated with
the event (event->ctx->task) is read using READ_ONCE at the beginning
of the function, checked, and then re-read from event->ctx->task,
voiding all guarantees of the checks. Reuse the value that was read by
READ_ONCE to ensure the consistency of the task struct throughout the
function.
Fixes: 375637bc52 ("perf/core: Introduce address range filtering")
Signed-off-by: Baptiste Lepers <baptiste.lepers@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20210906015310.12802-1-baptiste.lepers@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70f437fb43 upstream.
Dispatching requests inline with the .queue_rq() call may block while
holding the send_mutex. If the tcp io_work also happens to schedule, it
may see the req_list is non-empty, leaving "pending" true and remaining
in TASK_RUNNING. Since io_work is of higher scheduling priority, the
.queue_rq task may not get a chance to run, blocking forward progress
and leading to io timeouts.
Instead of checking for pending requests within io_work, let the queueing
restart io_work outside the send_mutex lock if there is more work to be
done.
Fixes: a0fdd14180 ("nvme-tcp: rerun io_work if req_list is not empty")
Reported-by: Samuel Jones <sjones@kalrayinc.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee27e330a9 upstream.
Fixes the below flow of sleeping in atomic context by releasing
the RCU lock before calling to free_match_list.
build_match_list() <- disables preempt
-> free_match_list()
-> tree_put_node()
-> down_write_ref_node() <- take write lock
Fixes: 693c6883bb ("net/mlx5: Add hash table for flow groups in flow table")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 57f0ff059e upstream.
It's later supposed to be either a correct address or NULL. Without the
initialization, it may contain an undefined value which results in the
following segmentation fault:
# perf top --sort comm -g --ignore-callees=do_idle
terminates with:
#0 0x00007ffff56b7685 in __strlen_avx2 () from /lib64/libc.so.6
#1 0x00007ffff55e3802 in strdup () from /lib64/libc.so.6
#2 0x00005555558cb139 in hist_entry__init (callchain_size=<optimized out>, sample_self=true, template=0x7fffde7fb110, he=0x7fffd801c250) at util/hist.c:489
#3 hist_entry__new (template=template@entry=0x7fffde7fb110, sample_self=sample_self@entry=true) at util/hist.c:564
#4 0x00005555558cb4ba in hists__findnew_entry (hists=hists@entry=0x5555561d9e38, entry=entry@entry=0x7fffde7fb110, al=al@entry=0x7fffde7fb420,
sample_self=sample_self@entry=true) at util/hist.c:657
#5 0x00005555558cba1b in __hists__add_entry (hists=hists@entry=0x5555561d9e38, al=0x7fffde7fb420, sym_parent=<optimized out>, bi=bi@entry=0x0, mi=mi@entry=0x0,
sample=sample@entry=0x7fffde7fb4b0, sample_self=true, ops=0x0, block_info=0x0) at util/hist.c:288
#6 0x00005555558cbb70 in hists__add_entry (sample_self=true, sample=0x7fffde7fb4b0, mi=0x0, bi=0x0, sym_parent=<optimized out>, al=<optimized out>, hists=0x5555561d9e38)
at util/hist.c:1056
#7 iter_add_single_cumulative_entry (iter=0x7fffde7fb460, al=<optimized out>) at util/hist.c:1056
#8 0x00005555558cc8a4 in hist_entry_iter__add (iter=iter@entry=0x7fffde7fb460, al=al@entry=0x7fffde7fb420, max_stack_depth=<optimized out>, arg=arg@entry=0x7fffffff7db0)
at util/hist.c:1231
#9 0x00005555557cdc9a in perf_event__process_sample (machine=<optimized out>, sample=0x7fffde7fb4b0, evsel=<optimized out>, event=<optimized out>, tool=0x7fffffff7db0)
at builtin-top.c:842
#10 deliver_event (qe=<optimized out>, qevent=<optimized out>) at builtin-top.c:1202
#11 0x00005555558a9318 in do_flush (show_progress=false, oe=0x7fffffff80e0) at util/ordered-events.c:244
#12 __ordered_events__flush (oe=oe@entry=0x7fffffff80e0, how=how@entry=OE_FLUSH__TOP, timestamp=timestamp@entry=0) at util/ordered-events.c:323
#13 0x00005555558a9789 in __ordered_events__flush (timestamp=<optimized out>, how=<optimized out>, oe=<optimized out>) at util/ordered-events.c:339
#14 ordered_events__flush (how=OE_FLUSH__TOP, oe=0x7fffffff80e0) at util/ordered-events.c:341
#15 ordered_events__flush (oe=oe@entry=0x7fffffff80e0, how=how@entry=OE_FLUSH__TOP) at util/ordered-events.c:339
#16 0x00005555557cd631 in process_thread (arg=0x7fffffff7db0) at builtin-top.c:1114
#17 0x00007ffff7bb817a in start_thread () from /lib64/libpthread.so.0
#18 0x00007ffff5656dc3 in clone () from /lib64/libc.so.6
If you look at the frame #2, the code is:
488 if (he->srcline) {
489 he->srcline = strdup(he->srcline);
490 if (he->srcline == NULL)
491 goto err_rawdata;
492 }
If he->srcline is not NULL (it is not NULL if it is uninitialized rubbish),
it gets strdupped and strdupping a rubbish random string causes the problem.
Also, if you look at the commit 1fb7d06a50, it adds the srcline property
into the struct, but not initializing it everywhere needed.
Committer notes:
Now I see, when using --ignore-callees=do_idle we end up here at line
2189 in add_callchain_ip():
2181 if (al.sym != NULL) {
2182 if (perf_hpp_list.parent && !*parent &&
2183 symbol__match_regex(al.sym, &parent_regex))
2184 *parent = al.sym;
2185 else if (have_ignore_callees && root_al &&
2186 symbol__match_regex(al.sym, &ignore_callees_regex)) {
2187 /* Treat this symbol as the root,
2188 forgetting its callees. */
2189 *root_al = al;
2190 callchain_cursor_reset(cursor);
2191 }
2192 }
And the al that doesn't have the ->srcline field initialized will be
copied to the root_al, so then, back to:
1211 int hist_entry_iter__add(struct hist_entry_iter *iter, struct addr_location *al,
1212 int max_stack_depth, void *arg)
1213 {
1214 int err, err2;
1215 struct map *alm = NULL;
1216
1217 if (al)
1218 alm = map__get(al->map);
1219
1220 err = sample__resolve_callchain(iter->sample, &callchain_cursor, &iter->parent,
1221 iter->evsel, al, max_stack_depth);
1222 if (err) {
1223 map__put(alm);
1224 return err;
1225 }
1226
1227 err = iter->ops->prepare_entry(iter, al);
1228 if (err)
1229 goto out;
1230
1231 err = iter->ops->add_single_entry(iter, al);
1232 if (err)
1233 goto out;
1234
That al at line 1221 is what hist_entry_iter__add() (called from
sample__resolve_callchain()) saw as 'root_al', and then:
iter->ops->add_single_entry(iter, al);
will go on with al->srcline with a bogus value, I'll add the above
sequence to the cset and apply, thanks!
Signed-off-by: Michael Petlan <mpetlan@redhat.com>
CC: Milian Wolff <milian.wolff@kdab.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Fixes: 1fb7d06a50 ("perf report Use srcline from callchain for hist entries")
Link: https //lore.kernel.org/r/20210719145332.29747-1-mpetlan@redhat.com
Reported-by: Juri Lelli <jlelli@redhat.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 040b8907cc upstream.
With the new static annotation, the compiler warns when the functions
are actually unused:
drivers/gpu/drm/rockchip/cdn-dp-core.c:1123:12: error: 'cdn_dp_resume' defined but not used [-Werror=unused-function]
1123 | static int cdn_dp_resume(struct device *dev)
| ^~~~~~~~~~~~~
Mark them __maybe_unused to suppress that warning as well.
[ Not so 'new' static annotations any more, and I removed the part of
the patch that added __maybe_unused to cdn_dp_suspend(), because it's
used by the shutdown/remove code.
So only the resume function ends up possibly unused if CONFIG_PM isn't
set - Linus ]
Fixes: 7c49abb4c2 ("drm/rockchip: cdn-dp-core: Make cdn_dp_core_suspend/resume static")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f4bb62e64c upstream.
In tipc_sk_enqueue() we use hardcoded 2 jiffies to extract
socket buffer from generic queue to particular socket.
The 2 jiffies is too short in case there are other high priority
tasks get CPU cycles for multiple jiffies update. As result, no
buffer could be enqueued to particular socket.
To solve this, we switch to use constant timeout 20msecs.
Then, the function will be expired between 2 jiffies (CONFIG_100HZ)
and 20 jiffies (CONFIG_1000HZ).
Fixes: c637c10355 ("tipc: resolve race problem at unicast message reception")
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e3f0cc1a94 upstream.
A number of users have reported that they were not able to get the PHY
to successfully link up, especially after commit c36757eb9d ("net:
phy: consider AN_RESTART status when reading link status") where we
stopped reading just BMSR, but we also read BMCR to determine the link
status.
Andrius at NetBSD did a wonderful job at debugging the problem
and found out that the MDIO bus clock frequency would be incorrectly set
back to its default value which would prevent the MDIO bus controller
from reading PHY registers properly. Back when we only read BMSR, if we
read all 1s, we could falsely indicate a link status, though in general
there is a cable plugged in, so this went unnoticed. After a second read
of BMCR was added, a wrong read will lead to the inability to determine
a link UP condition which is when it started to be visibly broken, even
if it was long before that.
The fix consists in restoring the value of the MD_CSR register that was
set prior to the MAC reset.
Link: http://gnats.netbsd.org/cgi-bin/query-pr-single.pl?number=53494
Fixes: 90f750a81a ("r6040: consolidate MAC reset to its own function")
Reported-by: Andrius V <vezhlys@gmail.com>
Reported-by: Darek Strugacz <darek.strugacz@op.pl>
Tested-by: Darek Strugacz <darek.strugacz@op.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b6ff7eb66 upstream.
The reference count leak issue may take place in an error handling
path. If both conditions of tunnel->version == L2TP_HDR_VER_3 and the
return value of l2tp_v3_ensure_opt_in_linear is nonzero, the function
would directly jump to label invalid, without decrementing the reference
count of the l2tp_session object session increased earlier by
l2tp_tunnel_get_session(). This may result in refcount leaks.
Fix this issue by decrease the reference count before jumping to the
label invalid.
Fixes: 4522a70db7 ("l2tp: fix reading optional fields of L2TPv3")
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9ea761fdd upstream.
Commit 2677d20677 ("dccp: don't free ccid2_hc_tx_sock ...") fixed
a UAF but reintroduced CVE-2017-6074.
When the sock is cloned, two dccps_hc_tx_ccid will reference to the
same ccid. So one can free the ccid object twice from two socks after
cloning.
This issue was found by "Hadar Manor" as well and assigned with
CVE-2020-16119, which was fixed in Ubuntu's kernel. So here I port
the patch from Ubuntu to fix it.
The patch prevents cloned socks from referencing the same ccid.
Fixes: 2677d20677 ("dccp: don't free ccid2_hc_tx_sock ...")
Signed-off-by: Zhenpeng Lin <zplin@psu.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7366c23ff4 upstream.
Building dp83640.c on arch/parisc/ produces a build warning for
PAGE0 being redefined. Since the macro is not used in the dp83640
driver, just make it a comment for documentation purposes.
In file included from ../drivers/net/phy/dp83640.c:23:
../drivers/net/phy/dp83640_reg.h:8: warning: "PAGE0" redefined
8 | #define PAGE0 0x0000
from ../drivers/net/phy/dp83640.c:11:
../arch/parisc/include/asm/page.h:187: note: this is the location of the previous definition
187 | #define PAGE0 ((struct zeropage *)__PAGE_OFFSET)
Fixes: cb646e2b02 ("ptp: Added a clock driver for the National Semiconductor PHYTER.")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Richard Cochran <richard.cochran@omicron.at>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210913220605.19682-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c3a0a018e upstream.
Remove the assert from the callback priv lookup function since it does
not require RTNL lock and is already protected by flow_indr_block_lock.
This will avoid warnings from being emitted to dmesg if the driver
registers its callback after an ingress qdisc was created for a
netdevice.
The warnings started after the following patch was merged:
commit 74fc4f8287 ("net: Fix offloading indirect devices dependency on qdisc order creation")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc19862ffe upstream.
syzbot reported an use-after-free crash:
BUG: KASAN: use-after-free in tipc_recvmsg+0xf77/0xf90 net/tipc/socket.c:1979
Call Trace:
tipc_recvmsg+0xf77/0xf90 net/tipc/socket.c:1979
sock_recvmsg_nosec net/socket.c:943 [inline]
sock_recvmsg net/socket.c:961 [inline]
sock_recvmsg+0xca/0x110 net/socket.c:957
tipc_conn_rcv_from_sock+0x162/0x2f0 net/tipc/topsrv.c:398
tipc_conn_recv_work+0xeb/0x190 net/tipc/topsrv.c:421
process_one_work+0x98d/0x1630 kernel/workqueue.c:2276
worker_thread+0x658/0x11f0 kernel/workqueue.c:2422
As Hoang pointed out, it was caused by skb_cb->bytes_read still accessed
after calling tsk_advance_rx_queue() to free the skb in tipc_recvmsg().
This patch is to fix it by accessing skb_cb->bytes_read earlier than
calling tsk_advance_rx_queue().
Fixes: f4919ff59c ("tipc: keep the skb in rcv queue until the whole data is read")
Reported-by: syzbot+e6741b97d5552f97c24d@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 34b1999da9 upstream.
Jiri Olsa reported a fault when running:
# cat /proc/kallsyms | grep ksys_read
ffffffff8136d580 T ksys_read
# objdump -d --start-address=0xffffffff8136d580 --stop-address=0xffffffff8136d590 /proc/kcore
/proc/kcore: file format elf64-x86-64
Segmentation fault
general protection fault, probably for non-canonical address 0xf887ffcbff000: 0000 [#1] SMP PTI
CPU: 12 PID: 1079 Comm: objdump Not tainted 5.14.0-rc5qemu+ #508
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-4.fc34 04/01/2014
RIP: 0010:kern_addr_valid
Call Trace:
read_kcore
? rcu_read_lock_sched_held
? rcu_read_lock_sched_held
? rcu_read_lock_sched_held
? trace_hardirqs_on
? rcu_read_lock_sched_held
? lock_acquire
? lock_acquire
? rcu_read_lock_sched_held
? lock_acquire
? rcu_read_lock_sched_held
? rcu_read_lock_sched_held
? rcu_read_lock_sched_held
? lock_release
? _raw_spin_unlock
? __handle_mm_fault
? rcu_read_lock_sched_held
? lock_acquire
? rcu_read_lock_sched_held
? lock_release
proc_reg_read
? vfs_read
vfs_read
ksys_read
do_syscall_64
entry_SYSCALL_64_after_hwframe
The fault happens because kern_addr_valid() dereferences existent but not
present PMD in the high kernel mappings.
Such PMDs are created when free_kernel_image_pages() frees regions larger
than 2Mb. In this case, a part of the freed memory is mapped with PMDs and
the set_memory_np_noalias() -> ... -> __change_page_attr() sequence will
mark the PMD as not present rather than wipe it completely.
Have kern_addr_valid() check whether higher level page table entries are
present before trying to dereference them to fix this issue and to avoid
similar issues in the future.
Stable backporting note:
------------------------
Note that the stable marking is for all active stable branches because
there could be cases where pagetable entries exist but are not valid -
see 9a14aefc1d ("x86: cpa, fix lookup_address"), for example. So make
sure to be on the safe side here and use pXY_present() accessors rather
than pXY_none() which could #GP when accessing pages in the direct map.
Also see:
c40a56a781 ("x86/mm/init: Remove freed kernel image areas from alias mapping")
for more info.
Reported-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: Dave Hansen <dave.hansen@intel.com>
Tested-by: Jiri Olsa <jolsa@redhat.com>
Cc: <stable@vger.kernel.org> # 4.4+
Link: https://lkml.kernel.org/r/20210819132717.19358-1-rppt@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aeef8b5089 upstream.
The end address passed to memtype_reserve() is handed directly to
sanitize_phys(). However, end is exclusive and sanitize_phys() expects
an inclusive address. If end falls at the end of the physical address
space, sanitize_phys() will return 0. This can result in drivers
failing to load, and the following warning:
WARNING: CPU: 26 PID: 749 at arch/x86/mm/pat.c:354 reserve_memtype+0x262/0x450
reserve_memtype failed: [mem 0x3ffffff00000-0xffffffffffffffff], req uncached-minus
Call Trace:
[<ffffffffa427b1f2>] reserve_memtype+0x262/0x450
[<ffffffffa42764aa>] ioremap_nocache+0x1a/0x20
[<ffffffffc04620a1>] mpt3sas_base_map_resources+0x151/0xa60 [mpt3sas]
[<ffffffffc0465555>] mpt3sas_base_attach+0xf5/0xa50 [mpt3sas]
---[ end trace 6d6eea4438db89ef ]---
ioremap reserve_memtype failed -22
mpt3sas_cm0: unable to map adapter memory! or resource not found
mpt3sas_cm0: failure at drivers/scsi/mpt3sas/mpt3sas_scsih.c:10597/_scsih_probe()!
Fix this by passing the inclusive end address to sanitize_phys().
Fixes: 510ee090ab ("x86/mm/pat: Prepare {reserve, free}_memtype() for "decoy" addresses")
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/x49o8a3pu5i.fsf@segfault.boston.devel.redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f2faea8b64 upstream.
When we forcefully evict a mapping from the the address space and thus the
MMU context, the MMU context is leaked, as the mapping no longer points to
it, so it doesn't get freed when the GEM object is destroyed. Add the
mssing context put to fix the leak.
Cc: stable@vger.kernel.org # 5.4
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d6408538f0 upstream.
Move the refcount manipulation of the MMU context to the point where the
hardware state is programmed. At that point it is also known if a previous
MMU state is still there, or the state needs to be reprogrammed with a
potentially different context.
Cc: stable@vger.kernel.org # 5.4
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f3eea9d01 upstream.
The MMU state may be kept across a runtime suspend/resume cycle, as we
avoid a full hardware reset to keep the latency of the runtime PM small.
Don't pretend that the MMU state is lost in driver state. The MMU
context is pushed out when new HW jobs with a different context are
coming in. The only exception to this is when the GPU is unbound, in
which case we need to make sure to also free the last active context.
Cc: stable@vger.kernel.org # 5.4
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23e0f5a57d upstream.
While the DMA frontend can only be active when the MMU context is set, the
reverse isn't necessarily true, as the frontend can be stopped while the
MMU state is kept. Stop treating mmu_context being set as a indication that
the frontend is running and instead add a explicit property.
Cc: stable@vger.kernel.org # 5.4
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cda7532916 upstream.
The prev context is the MMU context at the time of the job
queueing in hardware. As a job might be queued multiple times
due to recovery after a GPU hang, we need to make sure to put
the stale prev MMU context from a prior queuing, to avoid the
reference and thus the MMU context leaking.
Cc: stable@vger.kernel.org # 5.4
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e35ac9d0b5 upstream.
When we need a buffer for SVE register state we call sve_alloc() to make
sure that one is there. In order to avoid repeated allocations and frees
we keep the buffer around unless we change vector length and just memset()
it to ensure a clean register state. The function that deals with this
takes the task to operate on as an argument, however in the case where we
do a memset() we initialise using the SVE state size for the current task
rather than the task passed as an argument.
This is only an issue in the case where we are setting the register state
for a task via ptrace and the task being configured has a different vector
length to the task tracing it. In the case where the buffer is larger in
the traced process we will leak old state from the traced process to
itself, in the case where the buffer is smaller in the traced process we
will overflow the buffer and corrupt memory.
Fixes: bc0ee47603 ("arm64/sve: Core task context handling")
Cc: <stable@vger.kernel.org> # 4.15.x
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210909165356.10675-1-broonie@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 16c8d2df7e upstream.
When setting up the next segment, we check what type the iter is and
handle it accordingly. However, when incrementing and processed amount
we do not, and both iter advance and addr/len are adjusted, regardless
of type. Split the increment side just like we do on the setup side.
Fixes: 4017eb91a9 ("io_uring: make loop_rw_iter() use original user supplied pointers")
Cc: stable@vger.kernel.org
Reported-by: Valentina Palmiotti <vpalmiotti@gmail.com>
Reviewed-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f93e834fa upstream.
The mount option max_inline ranges from 0 to the sectorsize (which is
now equal to page size). But we parse the mount options too early and
before the actual sectorsize is read from the superblock. So the upper
limit of max_inline is unaware of the actual sectorsize and is limited
by the temporary sectorsize 4096, even on a system where the default
sectorsize is 64K.
Fix this by reading the superblock sectorsize before the mount option
parse.
Reported-by: Alexander Tsvetkov <alexander.tsvetkov@oracle.com>
CC: stable@vger.kernel.org # 5.4+
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fw_node pointer has already been retrieved, and using it allows
us to remove a downstream patch to the firmware driver.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
commit 6e3cd95234 upstream.
On recent Intel systems the HPET stops working when the system reaches PC10
idle state.
The approach of adding PCI ids to the early quirks to disable HPET on
these systems is a whack a mole game which makes no sense.
Check for PC10 instead and force disable HPET if supported. The check is
overbroad as it does not take ACPI, intel_idle enablement and command
line parameters into account. That's fine as long as there is at least
PMTIMER available to calibrate the TSC frequency. The decision can be
overruled by adding "hpet=force" on the kernel command line.
Remove the related early PCI quirks for affected Ice Cake and Coffin Lake
systems as they are not longer required. That should also cover all
other systems, i.e. Tiger Rag and newer generations, which are most
likely affected by this as well.
Fixes: Yet another hardware trainwreck
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Rafael J. Wysocki <rafael@kernel.org>
Cc: stable@vger.kernel.org
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3958b9c34c upstream.
Commit
3c73b81a91 ("x86/entry, selftests: Further improve user entry sanity checks")
added a warning if AC is set when in the kernel.
Commit
662a022189 ("x86/entry: Fix AC assertion")
changed the warning to only fire if the CPU supports SMAP.
However, the warning can still trigger on a machine that supports SMAP
but where it's disabled in the kernel config and when running the
syscall_nt selftest, for example:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 49 at irqentry_enter_from_user_mode
CPU: 0 PID: 49 Comm: init Tainted: G T 5.15.0-rc4+ #98 e6202628ee053b4f310759978284bd8bb0ce6905
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
RIP: 0010:irqentry_enter_from_user_mode
...
Call Trace:
? irqentry_enter
? exc_general_protection
? asm_exc_general_protection
? asm_exc_general_protectio
IS_ENABLED(CONFIG_X86_SMAP) could be added to the warning condition, but
even this would not be enough in case SMAP is disabled at boot time with
the "nosmap" parameter.
To be consistent with "nosmap" behaviour, clear X86_FEATURE_SMAP when
!CONFIG_X86_SMAP.
Found using entry-fuzz + satrandconfig.
[ bp: Massage commit message. ]
Fixes: 3c73b81a91 ("x86/entry, selftests: Further improve user entry sanity checks")
Fixes: 662a022189 ("x86/entry: Fix AC assertion")
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20211003223423.8666-1-vegard.nossum@oracle.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit eb8257a121 ]
On pseries LPAR when an empty slot is assigned to partition OR in single
LPAR mode, kdump kernel crashes during issuing PHB reset.
In the kdump scenario, we traverse all PHBs and issue reset using the
pe_config_addr of the first child device present under each PHB. However
the code assumes that none of the PHB slots can be empty and uses
list_first_entry() to get the first child device under the PHB. Since
list_first_entry() expects the list to be non-empty, it returns an
invalid pci_dn entry and ends up accessing NULL phb pointer under
pci_dn->phb causing kdump kernel crash.
This patch fixes the below kdump kernel crash by skipping empty slots:
audit: initializing netlink subsys (disabled)
thermal_sys: Registered thermal governor 'fair_share'
thermal_sys: Registered thermal governor 'step_wise'
cpuidle: using governor menu
pstore: Registered nvram as persistent store backend
Issue PHB reset ...
audit: type=2000 audit(1631267818.000:1): state=initialized audit_enabled=0 res=1
BUG: Kernel NULL pointer dereference on read at 0x00000268
Faulting instruction address: 0xc000000008101fb0
Oops: Kernel access of bad area, sig: 7 [#1]
LE PAGE_SIZE=64K MMU=Radix SMP NR_CPUS=2048 NUMA pSeries
Modules linked in:
CPU: 7 PID: 1 Comm: swapper/7 Not tainted 5.14.0 #1
NIP: c000000008101fb0 LR: c000000009284ccc CTR: c000000008029d70
REGS: c00000001161b840 TRAP: 0300 Not tainted (5.14.0)
MSR: 8000000002009033 <SF,VEC,EE,ME,IR,DR,RI,LE> CR: 28000224 XER: 20040002
CFAR: c000000008101f0c DAR: 0000000000000268 DSISR: 00080000 IRQMASK: 0
...
NIP pseries_eeh_get_pe_config_addr+0x100/0x1b0
LR __machine_initcall_pseries_eeh_pseries_init+0x2cc/0x350
Call Trace:
0xc00000001161bb80 (unreliable)
__machine_initcall_pseries_eeh_pseries_init+0x2cc/0x350
do_one_initcall+0x60/0x2d0
kernel_init_freeable+0x350/0x3f8
kernel_init+0x3c/0x17c
ret_from_kernel_thread+0x5c/0x64
Fixes: 5a090f7c36 ("powerpc/pseries: PCIE PHB reset")
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.ibm.com>
[mpe: Tweak wording and trim oops]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/163215558252.413351.8600189949820258982.stgit@jupiter
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59a4e0d551 ]
As far as I can tell this should be enabled on rv32 as well, I'm not
sure why it's rv64-only. checksyscalls is complaining about our lack of
clone3() on rv32.
Fixes: 56ac5e2139 ("riscv: enable sys_clone3 syscall for rv64")
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8bb0ab3ae7 ]
riscv architectures relying on mmap_sem for write in their
arch_setup_additional_pages. If the waiting task gets killed by the oom
killer it would block oom_reaper from asynchronous address space reclaim
and reduce the chances of timely OOM resolving. Wait for the lock in
the killable mode and return with EINTR if the task got killed while
waiting.
Signed-off-by: Tong Tiangen <tongtiangen@huawei.com>
Reviewed-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Fixes: 76d2a0493a ("RISC-V: Init and Halt Code")
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6558b646ce ]
acpi_i2c_find_adapter_by_handle() calls bus_find_device() which takes a
reference on the adapter which is never released which will result in a
reference count leak and render the adapter unremovable. Make sure to
put the adapter after creating the client in the same manner that we do
for OF.
Fixes: 525e6fabea ("i2c / ACPI: add support for ACPI reconfigure notifications")
Signed-off-by: Jamie Iles <quic_jiles@quicinc.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[wsa: fixed title]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23c216b335 ]
According to dma-api.rst, the dma_get_required_mask() helper should return
"the mask that the platform requires to operate efficiently". Which in
the case of PPC64 means the bypass mask and not a mask from an IOMMU table
which is shorter and slower to use due to map/unmap operations (especially
expensive on "pseries").
However the existing implementation ignores the possibility of bypassing
and returns the IOMMU table mask on the pseries platform which makes some
drivers (mpt3sas is one example) choose 32bit DMA even though bypass is
supported. The powernv platform sort of handles it by having a bigger
default window with a mask >=40 but it only works as drivers choose
63/64bit if the required mask is >32 which is rather pointless.
This reintroduces the bypass capability check to let drivers make
a better choice of the DMA mask.
Fixes: f1565c24b5 ("powerpc: use the generic dma_ops_bypass mode")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210930034454.95794-1-aik@ozlabs.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d6c414cd2 ]
The commit 6da5b0f027 ("net: ensure unbound datagram socket to be
chosen when not in a VRF") modified compute_score() so that a device
match is always made, not just in the case of an l3mdev skb, then
increments the score also for unbound sockets. This ensures that
sockets bound to an l3mdev are never selected when not in a VRF.
But as unbound and bound sockets are now scored equally, this results
in the last opened socket being selected if there are matches in the
default VRF for an unbound socket and a socket bound to a dev that is
not an l3mdev. However, handling prior to this commit was to always
select the bound socket in this case. Reinstate this handling by
incrementing the score only for bound sockets. The required isolation
due to choosing between an unbound socket and a socket bound to an
l3mdev remains in place due to the device match always being made.
The same approach is taken for compute_score() for stream sockets.
Fixes: 6da5b0f027 ("net: ensure unbound datagram socket to be chosen when not in a VRF")
Fixes: e78190581a ("net: ensure unbound stream socket to be chosen when not in a VRF")
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/cf0a8523-b362-1edf-ee78-eef63cbbb428@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e5a20573a ]
When VSI set up failed in i40e_probe() as part of PF switch set up
driver was trying to free misc IRQ vectors in
i40e_clear_interrupt_scheme and produced a kernel Oops:
Trying to free already-free IRQ 266
WARNING: CPU: 0 PID: 5 at kernel/irq/manage.c:1731 __free_irq+0x9a/0x300
Workqueue: events work_for_cpu_fn
RIP: 0010:__free_irq+0x9a/0x300
Call Trace:
? synchronize_irq+0x3a/0xa0
free_irq+0x2e/0x60
i40e_clear_interrupt_scheme+0x53/0x190 [i40e]
i40e_probe.part.108+0x134b/0x1a40 [i40e]
? kmem_cache_alloc+0x158/0x1c0
? acpi_ut_update_ref_count.part.1+0x8e/0x345
? acpi_ut_update_object_reference+0x15e/0x1e2
? strstr+0x21/0x70
? irq_get_irq_data+0xa/0x20
? mp_check_pin_attr+0x13/0xc0
? irq_get_irq_data+0xa/0x20
? mp_map_pin_to_irq+0xd3/0x2f0
? acpi_register_gsi_ioapic+0x93/0x170
? pci_conf1_read+0xa4/0x100
? pci_bus_read_config_word+0x49/0x70
? do_pci_enable_device+0xcc/0x100
local_pci_probe+0x41/0x90
work_for_cpu_fn+0x16/0x20
process_one_work+0x1a7/0x360
worker_thread+0x1cf/0x390
? create_worker+0x1a0/0x1a0
kthread+0x112/0x130
? kthread_flush_work_fn+0x10/0x10
ret_from_fork+0x1f/0x40
The problem is that at that point misc IRQ vectors
were not allocated yet and we get a call trace
that driver is trying to free already free IRQ vectors.
Add a check in i40e_clear_interrupt_scheme for __I40E_MISC_IRQ_REQUESTED
PF state before calling i40e_free_misc_vector. This state is set only if
misc IRQ vectors were properly initialized.
Fixes: c17401a1dd ("i40e: use separate state bit for miscellaneous IRQ setup")
Reported-by: PJ Waskiewicz <pwaskiewicz@jumptrading.com>
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 857b6c6f66 ]
The loop in i40e_get_capabilities can never end. The problem is that
although i40e_aq_discover_capabilities returns with an error if there's
a firmware problem, the returned error is not checked. There is a check for
pf->hw.aq.asq_last_status but that value is set to I40E_AQ_RC_OK on most
firmware problems.
When i40e_aq_discover_capabilities encounters a firmware problem, it will
encounter the same problem on its next invocation. As the result, the loop
becomes endless. We hit this with I40E_ERR_ADMIN_QUEUE_TIMEOUT but looking
at the code, it can happen with a range of other firmware errors.
I don't know what the correct behavior should be: whether the firmware
should be retried a few times, or whether pf->hw.aq.asq_last_status should
be always set to the encountered firmware error (but then it would be
pointless and can be just replaced by the i40e_aq_discover_capabilities
return value). However, the current behavior with an endless loop under the
rtnl mutex(!) is unacceptable and Intel has not submitted a fix, although we
explained the bug to them 7 months ago.
This may not be the best possible fix but it's better than hanging the whole
system on a firmware bug.
Fixes: 56a62fc868 ("i40e: init code and hardware support")
Tested-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d343679919 ]
rtnl_fill_statsinfo() is filling skb with one mandatory if_stats_msg structure.
nlmsg_put(skb, pid, seq, type, sizeof(struct if_stats_msg), flags);
But if_nlmsg_stats_size() never considered the needed storage.
This bug did not show up because alloc_skb(X) allocates skb with
extra tailroom, because of added alignments. This could very well
be changed in the future to have deterministic behavior.
Fixes: 10c9ead9f3 ("rtnetlink: add new RTM_GETSTATS message to dump link stats")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Roopa Prabhu <roopa@nvidia.com>
Acked-by: Roopa Prabhu <roopa@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 922aa9bcac ]
Prevent possible crashes when cleaning up after unsuccessful
initializations.
Fixes: 893ce44df5 ("gve: Add basic driver framework for Compute Engine Virtual NIC")
Signed-off-by: Tao Liu <xliutaox@google.com>
Signed-off-by: Catherine Sully <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d03477ee10 ]
The qpl_map_size is rounded up to a multiple of sizeof(long), but the
number of qpls doesn't have to be.
Fixes: f5cedc84a3 ("gve: Add transmit and receive support")
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: Jeroen de Borst <jeroendb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11b8e2bb98 ]
The gbefb driver not only registers a driver but also the device for that
driver. This is all well and good when run on the IP32 machines that are
supported by the driver but since the driver supports building with
COMPILE_TEST we might also be building on other platforms which do not have
this hardware and will crash instantiating the driver. Add an IS_ENABLED()
check so we compile out the device registration if we don't have the Kconfig
option for the machine enabled.
Fixes: 552ccf6b25 ("video: fbdev: gbefb: add COMPILE_TEST support")
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921212102.30803-1-broonie@kernel.org
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c64c8e04a1 ]
Recent rework, which made HDMI PHY driver a platform device, inadvertely
reversed clock setup order. HW is very touchy about it. Proper way is to
handle controllers resets and clocks first and HDMI PHYs second.
Currently, without this fix, first mode set completely fails (nothing on
HDMI monitor) on H3 era PHYs. On H6, it still somehow work.
Move HDMI PHY reset & clocks handling to sun8i_hdmi_phy_init() which
will assure that code is executed after controllers reset & clocks are
handled. Additionally, add sun8i_hdmi_phy_deinit() which will deinit
them at controllers driver unload.
Tested on A64, H3, H6 and R40.
Fixes: 9bf3797796 ("drm/sun4i: dw-hdmi: Make HDMI PHY into a platform device")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210915175836.3158839-1-jernej.skrabec@gmail.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b13a270ace ]
Commit 94f6345712 ("bus: ti-sysc: Implement quirk handling for
CLKDM_NOAUTO") should have also added the quirk for dra7 dcan1 in
addition to dcan2 for errata i893 handling.
Let's also pass the quirk flag for legacy mode booting for if "ti,hwmods"
dts property is used with related dcan hwmod data. This should be only
needed if anybody needs to git bisect earlier stable trees though.
Fixes: 94f6345712 ("bus: ti-sysc: Implement quirk handling for CLKDM_NOAUTO")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7707a4d01a ]
While existing code is correct, KCSAN is reporting
a data-race in netlink_insert / netlink_sendmsg [1]
It is correct to read nlk->bound without a lock, as netlink_autobind()
will acquire all needed locks.
[1]
BUG: KCSAN: data-race in netlink_insert / netlink_sendmsg
write to 0xffff8881031c8b30 of 1 bytes by task 18752 on cpu 0:
netlink_insert+0x5cc/0x7f0 net/netlink/af_netlink.c:597
netlink_autobind+0xa9/0x150 net/netlink/af_netlink.c:842
netlink_sendmsg+0x479/0x7c0 net/netlink/af_netlink.c:1892
sock_sendmsg_nosec net/socket.c:703 [inline]
sock_sendmsg net/socket.c:723 [inline]
____sys_sendmsg+0x360/0x4d0 net/socket.c:2392
___sys_sendmsg net/socket.c:2446 [inline]
__sys_sendmsg+0x1ed/0x270 net/socket.c:2475
__do_sys_sendmsg net/socket.c:2484 [inline]
__se_sys_sendmsg net/socket.c:2482 [inline]
__x64_sys_sendmsg+0x42/0x50 net/socket.c:2482
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffff8881031c8b30 of 1 bytes by task 18751 on cpu 1:
netlink_sendmsg+0x270/0x7c0 net/netlink/af_netlink.c:1891
sock_sendmsg_nosec net/socket.c:703 [inline]
sock_sendmsg net/socket.c:723 [inline]
__sys_sendto+0x2a8/0x370 net/socket.c:2019
__do_sys_sendto net/socket.c:2031 [inline]
__se_sys_sendto net/socket.c:2027 [inline]
__x64_sys_sendto+0x74/0x90 net/socket.c:2027
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0x00 -> 0x01
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 18751 Comm: syz-executor.0 Not tainted 5.14.0-rc1-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: da314c9923 ("netlink: Replace rhash_portid with bound")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0854a05133 ]
Commit de1799667b ("net: bridge: add STP xstats")
added an additional nla_reserve_64bit() in br_fill_linkxstats(),
but forgot to update br_get_linkxstats_size() accordingly.
This can trigger the following in rtnl_stats_get()
WARN_ON(err == -EMSGSIZE);
Fixes: de1799667b ("net: bridge: add STP xstats")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Nikolay Aleksandrov <nikolay@nvidia.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dbe0b88064 ]
bridge_fill_linkxstats() is using nla_reserve_64bit().
We must use nla_total_size_64bit() instead of nla_total_size()
for corresponding data structure.
Fixes: 1080ab95e3 ("net: bridge: add support for IGMP/MLD stats and export them via netlink")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Nikolay Aleksandrov <nikolay@nvidia.com>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 783f3db030 ]
Any pending interrupt can prevent entering standby based power off state.
To avoid it, disable the GIC CPU interface.
Fixes: 8148d21360 ("ARM: imx6: register pm_power_off handler if "fsl,pmic-stby-poweroff" is set")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04fa4f03e3 ]
The LS1028A has two FlexCAN controller. These are compatible with
the ones from the LX2160A. Add the nodes.
The first controller was tested on the Kontron sl28 board.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7cd8b1542a ]
The driver can't be loaded automatically because it misses
module alias to be provided. Add corresponding MODULE_DEVICE_TABLE()
call to the driver.
Fixes: 863d08ece9 ("supports eg20t ptp clock")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eed183abc0 ]
Property phy-connection-type contains invalid value "sgmii-2500" per scheme
defined in file ethernet-controller.yaml.
Correct phy-connection-type value should be "2500base-x".
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 84e0f1c138 ("powerpc/mpc85xx: Add MDIO bus muxing support to the board device tree(s)")
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9a10440f0 ]
Currently in Rx data path IPsec crypto offloaded packets uses
csum_none flag, so checksum is handled by the stack, this naturally
have some performance/cpu utilization impact on such flows. As Nvidia
NIC starting from ConnectX6DX provides checksum complete value out of
the box also for such flows there is no sense in taking csum_none path,
furthermore the stack (xfrm) have the method to handle checksum complete
corrections for such flows i.e. IPsec trailer removal and consequently
checksum value adjustment.
Because of the above and in addition the ConnectX6DX is the first HW
which supports IPsec crypto offload then it is safe to report csum
complete for IPsec offloaded traffic.
Fixes: b2ac7541e3 ("net/mlx5e: IPsec: Add Connect-X IPsec Rx data path offload")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30e29a9a2b ]
In prealloc_elems_and_freelist(), the multiplication to calculate the
size passed to bpf_map_area_alloc() could lead to an integer overflow.
As a result, out-of-bounds write could occur in pcpu_freelist_populate()
as reported by KASAN:
[...]
[ 16.968613] BUG: KASAN: slab-out-of-bounds in pcpu_freelist_populate+0xd9/0x100
[ 16.969408] Write of size 8 at addr ffff888104fc6ea0 by task crash/78
[ 16.970038]
[ 16.970195] CPU: 0 PID: 78 Comm: crash Not tainted 5.15.0-rc2+ #1
[ 16.970878] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014
[ 16.972026] Call Trace:
[ 16.972306] dump_stack_lvl+0x34/0x44
[ 16.972687] print_address_description.constprop.0+0x21/0x140
[ 16.973297] ? pcpu_freelist_populate+0xd9/0x100
[ 16.973777] ? pcpu_freelist_populate+0xd9/0x100
[ 16.974257] kasan_report.cold+0x7f/0x11b
[ 16.974681] ? pcpu_freelist_populate+0xd9/0x100
[ 16.975190] pcpu_freelist_populate+0xd9/0x100
[ 16.975669] stack_map_alloc+0x209/0x2a0
[ 16.976106] __sys_bpf+0xd83/0x2ce0
[...]
The possibility of this overflow was originally discussed in [0], but
was overlooked.
Fix the integer overflow by changing elem_size to u64 from u32.
[0] https://lore.kernel.org/bpf/728b238e-a481-eb50-98e9-b0f430ab01e7@gmail.com/
Fixes: 557c0c6e7d ("bpf: convert stackmap to pre-allocation")
Signed-off-by: Tatsuhiko Yasumatsu <th.yasumatsu@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210930135545.173698-1-th.yasumatsu@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b232537074 ]
Starting with v5.15-rc1, we may now see some am335x beaglebone black
device produce the following error on pruss probe:
Unhandled fault: external abort on non-linefetch (0x1008) at 0xe0326000
This has started with the enabling of pruss for am335x in the dts files.
Turns out the is caused by the PRM reset handling not waiting for the
reset bit to clear. To fix the issue, let's always wait for the reset
bit to clear, even if there is a separate reset status register.
We attempted to fix a similar issue for dra7 iva with a udelay() in
commit effe89e400 ("soc: ti: omap-prm: Fix occasional abort on reset
deassert for dra7 iva"). There is no longer a need for the udelay()
for dra7 iva reset either with the check added for reset bit clearing.
Cc: Drew Fustini <pdp7pdp7@gmail.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: "H. Nikolaus Schaller" <hns@goldelico.com>
Cc: Robert Nelson <robertcnelson@gmail.com>
Cc: Yongqin Liu <yongqin.liu@linaro.org>
Fixes: effe89e400 ("soc: ti: omap-prm: Fix occasional abort on reset deassert for dra7 iva")
Reported-by: Matti Vaittinen <mazziesaccount@gmail.com>
Tested-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79e3445b38 ]
On ARM CPUs that lack div/mod instructions, ALU32 BPF_DIV and BPF_MOD are
implemented using a call to a helper function. Before, the emitted code
for those function calls failed to preserve caller-saved ARM registers.
Since some of those registers happen to be mapped to BPF registers, it
resulted in eBPF register values being overwritten.
This patch emits code to push and pop the remaining caller-saved ARM
registers r2-r3 into the stack during the div/mod function call. ARM
registers r0-r1 are used as arguments and return value, and those were
already saved and restored correctly.
Fixes: 39c13c204b ("arm: eBPF JIT compiler")
Signed-off-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe5c735d0d ]
There is a Killer AX1650 2x2 Wi-Fi 6 and Bluetooth 5.1 wireless adapter
found on Dell XPS 15 (9510) laptop, its configuration was present on
Linux v5.7, however accidentally it has been removed from the list of
supported devices, let's add it back.
The problem is manifested on driver initialization:
Intel(R) Wireless WiFi driver for Linux
iwlwifi 0000:00:14.3: enabling device (0000 -> 0002)
iwlwifi: No config found for PCI dev 43f0/1651, rev=0x354, rfid=0x10a100
iwlwifi: probe of 0000:00:14.3 failed with error -22
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=213939
Fixes: 3f910a2583 ("iwlwifi: pcie: convert all AX101 devices to the device tables")
Cc: Julien Wajsberg <felash@gmail.com>
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Acked-by: Luca Coelho <luca@coelho.fi>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210924122154.2376577-1-vladimir.zapolskiy@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d67ed2510d ]
CONFIG_OF can be set by a randconfig or by a user -- without setting the
early flattree option (OF_EARLY_FLATTREE). This causes build errors.
However, if randconfig or a user sets USE_OF in the Xtensa config,
the right kconfig symbols are set to fix the build.
Fixes these build errors:
../arch/xtensa/kernel/setup.c:67:19: error: ‘__dtb_start’ undeclared here (not in a function); did you mean ‘dtb_start’?
67 | void *dtb_start = __dtb_start;
| ^~~~~~~~~~~
../arch/xtensa/kernel/setup.c: In function 'xtensa_dt_io_area':
../arch/xtensa/kernel/setup.c:201:14: error: implicit declaration of function 'of_flat_dt_is_compatible'; did you mean 'of_machine_is_compatible'? [-Werror=implicit-function-declaration]
201 | if (!of_flat_dt_is_compatible(node, "simple-bus"))
../arch/xtensa/kernel/setup.c:204:18: error: implicit declaration of function 'of_get_flat_dt_prop' [-Werror=implicit-function-declaration]
204 | ranges = of_get_flat_dt_prop(node, "ranges", &len);
../arch/xtensa/kernel/setup.c:204:16: error: assignment to 'const __be32 *' {aka 'const unsigned int *'} from 'int' makes pointer from integer without a cast [-Werror=int-conversion]
204 | ranges = of_get_flat_dt_prop(node, "ranges", &len);
| ^
../arch/xtensa/kernel/setup.c: In function 'early_init_devtree':
../arch/xtensa/kernel/setup.c:228:9: error: implicit declaration of function 'early_init_dt_scan'; did you mean 'early_init_devtree'? [-Werror=implicit-function-declaration]
228 | early_init_dt_scan(params);
../arch/xtensa/kernel/setup.c:229:9: error: implicit declaration of function 'of_scan_flat_dt' [-Werror=implicit-function-declaration]
229 | of_scan_flat_dt(xtensa_dt_io_area, NULL);
xtensa-elf-ld: arch/xtensa/mm/mmu.o:(.text+0x0): undefined reference to `xtensa_kio_paddr'
Fixes: da844a8177 ("xtensa: add device trees support")
Fixes: 6cb971114f ("xtensa: remap io area defined in device tree")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb8c3a3c52 ]
Randconfig builds still show a failure for the ath5k driver,
similar to the one that was fixed for ath9k earlier:
WARNING: unmet direct dependencies detected for MAC80211_LEDS
Depends on [n]: NET [=y] && WIRELESS [=y] && MAC80211 [=y] && (LEDS_CLASS [=m]=y || LEDS_CLASS [=m]=MAC80211 [=y])
Selected by [m]:
- ATH5K [=m] && NETDEVICES [=y] && WLAN [=y] && WLAN_VENDOR_ATH [=y] && (PCI [=y] || ATH25) && MAC80211 [=y]
net/mac80211/led.c: In function 'ieee80211_alloc_led_names':
net/mac80211/led.c:34:22: error: 'struct led_trigger' has no member named 'name'
34 | local->rx_led.name = kasprintf(GFP_KERNEL, "%srx",
| ^
Copying the same logic from my ath9k patch makes this one work
as well, stubbing out the calls to the LED subsystem.
Fixes: b64acb28da ("ath9k: fix build error with LEDS_CLASS=m")
Fixes: 72cdab8087 ("ath9k: Do not select MAC80211_LEDS by default")
Fixes: 3a078876ca ("ath5k: convert LED code to use mac80211 triggers")
Link: https://lore.kernel.org/all/20210722105501.1000781-1-arnd@kernel.org/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210920122359.353810-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 450e7fe9b1 ]
Currently, it is no longer possible to retrieve a DHCP address
on the imx6qdl-pico board.
This issue has been exposed by commit f5d9aa79df ("ARM: imx6q:
remove clk-out fixup for the Atheros AR8031 and AR8035 PHYs").
Fix it by describing the qca,clk-out-frequency property as suggested
by the commit above.
Fixes: 98670a0bb0 ("ARM: dts: imx6qdl: Add imx6qdl-pico support")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c187e2eb3 ]
The MIC2025 switch input signal nEN is active low, describe it as such
in the DT. The previous change to this regulator polarity was incorrectly
influenced by broken quirks in gpiolib-of.c, which is now long fixed. So
fix this regulator polarity setting here once and for all.
Fixes: 3c3601cd6a ("ARM: dts: imx53: Update USB configuration on M53Menlo")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8c1efe14a ]
The panel already contains pinctrl-0 phandle, but it is missing
the default pinctrl-names property, so the pin configuration is
ignored. Fill in the missing pinctrl-names property, so the pin
configuration is applied.
Fixes: d81765d693 ("ARM: dts: imx53: Update LCD panel node on M53Menlo")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 833d51d7c6 ]
PT_LOAD type denotes that the segment should be loaded into the final
firmware memory region. Hash segment is not one such, because it's only
needed for PAS init and shouldn't be in the final firmware memory region.
That's why mdt_phdr_valid() explicitly reject non PT_LOAD segment and
hash segment. This actually makes the hash segment type check in
qcom_mdt_read_metadata() unnecessary and redundant. For a hash segment,
it won't be loaded into firmware memory region anyway, due to the
QCOM_MDT_TYPE_HASH check in mdt_phdr_valid(), even if it has a PT_LOAD
type for some reason (misusing or abusing?).
Some firmware files on Sony phones are such examples, e.g WCNSS firmware
of Sony Xperia M4 Aqua phone. The type of hash segment is just PT_LOAD.
Drop the unnecessary hash segment type check in qcom_mdt_read_metadata()
to fix firmware loading failure on these phones, while hash segment is
still kept away from the final firmware memory region.
Fixes: 498b98e939 ("soc: qcom: mdt_loader: Support loading non-split images")
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210828070202.7033-1-shawn.guo@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1db21c315 ]
The 28NM DSI PLL driver for msm8960 calculates with a 27MHz reference
clock and should hence use PXO, not CXO which runs at 19.2MHz.
Note that none of the DSI PHY/PLL drivers currently use this "ref"
clock; they all rely on (sometimes inexistant) global clock names and
usually function normally without a parent clock. This discrepancy will
be corrected in a future patch, for which this change needs to be in
place first.
Fixes: 6969d1d9c6 ("ARM: dts: qcom-apq8064: Set 'cxo_board' as ref clock of the DSI PHY")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Link: https://lore.kernel.org/r/20210829203027.276143-2-marijn.suijten@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e879f855e5 ]
After commit a6d90e9f22 ("bus: ti-sysc: AM3: RNG is GP only"), clang
with -Wimplicit-fallthrough enabled warns:
drivers/bus/ti-sysc.c:2958:3: warning: unannotated fall-through between
switch labels [-Wimplicit-fallthrough]
default:
^
drivers/bus/ti-sysc.c:2958:3: note: insert 'break;' to avoid
fall-through
default:
^
break;
1 warning generated.
Clang's version of this warning is a little bit more pedantic than
GCC's. Add the missing break to satisfy it to match what has been done
all over the kernel tree.
Fixes: a6d90e9f22 ("bus: ti-sysc: AM3: RNG is GP only")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9b663b34c9 upstream.
Since the LED multicolor framework support was added in commit
92a81562e6 ("leds: lp55xx: Add multicolor framework support to lp55xx")
LEDs on this platform stopped working.
Author of the framework attempted to accommodate this DT to the
framework in commit b86d3d21cd ("ARM: dts: imx6dl-yapp4: Add reg property
to the lp5562 channel node") but that is not sufficient. A color property
is now required even if the multicolor framework is not used, otherwise
the driver probe fails:
lp5562: probe of 1-0030 failed with error -22
Add the color property to fix this.
Fixes: 92a81562e6 ("leds: lp55xx: Add multicolor framework support to lp55xx")
Cc: <stable@vger.kernel.org>
Cc: linux-leds@vger.kernel.org
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2ba5acfb34 upstream.
If sd_max is unsigned, then sd_max - GSS_SEQ_WIN is a very large number
whenever sd_max is less than GSS_SEQ_WIN, and the comparison:
seq_num <= sd->sd_max - GSS_SEQ_WIN
in gss_check_seq_num is pretty much always true, even when that's
clearly not what was intended.
This was causing pynfs to hang when using krb5, because pynfs uses zero
as the initial gss sequence number. That's perfectly legal, but this
logic error causes knfsd to drop the rpc in that case. Out-of-order
sequence IDs in the first GSS_SEQ_WIN (128) calls will also cause this.
Fixes: 10b9d99a3d ("SUNRPC: Augment server-side rpcgss tracepoints")
Cc: stable@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f2e717d655 upstream.
RFC3530 notes that the 'dircount' field may be zero, in which case the
recommendation is to ignore it, and only enforce the 'maxcount' field.
In RFC5661, this recommendation to ignore a zero valued field becomes a
requirement.
Fixes: aee3776441 ("nfsd4: fix rd_dircount enforcement")
Cc: <stable@vger.kernel.org>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d625050c7 upstream.
init_nfsd() should not unregister pernet subsys if the register fails
but should instead unwind from the last successful operation which is
register_filesystem().
Unregistering a failed register_pernet_subsys() call can result in
a kernel GPF as revealed by programmatically injecting an error in
register_pernet_subsys().
Verified the fix handled failure gracefully with no lingering nfsd
entry in /proc/filesystems. This change was introduced by the commit
bd5ae9288d ("nfsd: register pernet ops last, unregister first"),
the original error handling logic was correct.
Fixes: bd5ae9288d ("nfsd: register pernet ops last, unregister first")
Cc: stable@vger.kernel.org
Signed-off-by: Patrick Ho <Patrick.Ho@netapp.com>
Acked-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1dc1eed46f upstream.
Normally the check at open time suffices, but e.g loop device does set
IOCB_DIRECT after doing its own checks (which are not sufficent for
overlayfs).
Make sure we don't call the underlying filesystem read/write method with
the IOCB_DIRECT if it's not supported.
Reported-by: Huang Jianan <huangjianan@oppo.com>
Fixes: 16914e6fc7 ("ovl: add ovl_read_iter()")
Cc: <stable@vger.kernel.org> # v4.19
Tested-by: Huang Jianan <huangjianan@oppo.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a38a4d51c upstream.
The memory at the end of the controller only accepts 32bit read/write
accesses, but the arm64 memcpy_to/fromio implementation only uses 64bit
(which will be split into two 32bit access) and 8bit leading to incomplete
copies to/from this memory when the buffer is not multiple of 8bytes.
Add a local copy using writel/readl accesses to make sure we use the right
memory access width.
The switch to memcpy_to/fromio was done because of 285133040e
("arm64: Import latest memcpy()/memmove() implementation"), but using memcpy
worked before since it mainly used 32bit memory acceses.
Fixes: 103a5348c2 ("mmc: meson-gx: use memcpy_to/fromio for dram-access-quirk")
Reported-by: Christian Hewitt <christianshewitt@gmail.com>
Suggested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210928073652.434690-1-narmstrong@baylibre.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 65a205e611 upstream.
A recent change that started reporting break events to the line
discipline caused the tty-buffer insertions to no longer be serialised
by inserting events also from the completion handler for the interrupt
endpoint.
Completion calls for distinct endpoints are not guaranteed to be
serialised. For example, in case a host-controller driver uses
bottom-half completion, the interrupt and bulk-in completion handlers
can end up running in parallel on two CPUs (high-and low-prio tasklets,
respectively) thereby breaking the tty layer's single producer
assumption.
Fix this by holding the read lock also when inserting characters from
the bulk endpoint.
Fixes: 08dff274ed ("cdc-acm: fix BREAK rx code path adding necessary calls")
Cc: stable@vger.kernel.org
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210929090937.7410-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8253a34bfa upstream.
When passing 'phys' in the devicetree to describe the USB PHY phandle
(which is the recommended way according to
Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt) the
following NULL pointer dereference is observed on i.MX7 and i.MX8MM:
[ 1.489344] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000098
[ 1.498170] Mem abort info:
[ 1.500966] ESR = 0x96000044
[ 1.504030] EC = 0x25: DABT (current EL), IL = 32 bits
[ 1.509356] SET = 0, FnV = 0
[ 1.512416] EA = 0, S1PTW = 0
[ 1.515569] FSC = 0x04: level 0 translation fault
[ 1.520458] Data abort info:
[ 1.523349] ISV = 0, ISS = 0x00000044
[ 1.527196] CM = 0, WnR = 1
[ 1.530176] [0000000000000098] user address but active_mm is swapper
[ 1.536544] Internal error: Oops: 96000044 [#1] PREEMPT SMP
[ 1.542125] Modules linked in:
[ 1.545190] CPU: 3 PID: 7 Comm: kworker/u8:0 Not tainted 5.14.0-dirty #3
[ 1.551901] Hardware name: Kontron i.MX8MM N801X S (DT)
[ 1.557133] Workqueue: events_unbound deferred_probe_work_func
[ 1.562984] pstate: 80000005 (Nzcv daif -PAN -UAO -TCO BTYPE=--)
[ 1.568998] pc : imx7d_charger_detection+0x3f0/0x510
[ 1.573973] lr : imx7d_charger_detection+0x22c/0x510
This happens because the charger functions check for the phy presence
inside the imx_usbmisc_data structure (data->usb_phy), but the chipidea
core populates the usb_phy passed via 'phys' inside 'struct ci_hdrc'
(ci->usb_phy) instead.
This causes the NULL pointer dereference inside imx7d_charger_detection().
Fix it by also searching for 'phys' in case 'fsl,usbphy' is not found.
Tested on a imx7s-warp board.
Fixes: 746f316b75 ("usb: chipidea: introduce imx7d USB charger detection")
Cc: stable@vger.kernel.org
Reported-by: Heiko Thiery <heiko.thiery@gmail.com>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210921113754.767631-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a8526a5cd upstream.
Many users are reporting that the Samsung 860 and 870 SSD are having
various issues when combined with AMD/ATI (vendor ID 0x1002) SATA
controllers and only completely disabling NCQ helps to avoid these
issues.
Always disabling NCQ for Samsung 860/870 SSDs regardless of the host
SATA adapter vendor will cause I/O performance degradation with well
behaved adapters. To limit the performance impact to ATI adapters,
introduce the ATA_HORKAGE_NO_NCQ_ON_ATI flag to force disable NCQ
only for these adapters.
Also, two libata.force parameters (noncqati and ncqati) are introduced
to disable and enable the NCQ for the system which equipped with ATI
SATA adapter and Samsung 860 and 870 SSDs. The user can determine NCQ
function to be enabled or disabled according to the demand.
After verifying the chipset from the user reports, the issue appears
on AMD/ATI SB7x0/SB8x0/SB9x0 SATA Controllers and does not appear on
recent AMD SATA adapters. The vendor ID of ATI should be 0x1002.
Therefore, ATA_HORKAGE_NO_NCQ_ON_AMD was modified to
ATA_HORKAGE_NO_NCQ_ON_ATI.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=201693
Signed-off-by: Kate Hsuan <hpa@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210903094411.58749-1-hpa@redhat.com
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Cc: Krzysztof Olędzki <ole@ans.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 02d029a41d upstream.
perf_init_event tries multiple init callbacks and does not reset the
event state between tries. When x86_pmu_event_init runs, it
unconditionally sets the destroy callback to hw_perf_event_destroy. On
the next init attempt after x86_pmu_event_init, in perf_try_init_event,
if the pmu's capabilities includes PERF_PMU_CAP_NO_EXCLUDE, the destroy
callback will be run. However, if the next init didn't set the destroy
callback, hw_perf_event_destroy will be run (since the callback wasn't
reset).
Looking at other pmu init functions, the common pattern is to only set
the destroy callback on a successful init. Resetting the callback on
failure tries to replicate that pattern.
This was discovered after commit f11dd0d805 ("perf/x86/amd/ibs: Extend
PERF_PMU_CAP_NO_EXCLUDE to IBS Op") when the second (and only second)
run of the perf tool after a reboot results in 0 samples being
generated. The extra run of hw_perf_event_destroy results in
active_events having an extra decrement on each perf run. The second run
has active_events == 0 and every subsequent run has active_events < 0.
When active_events == 0, the NMI handler will early-out and not record
any samples.
Signed-off-by: Anand K Mistry <amistry@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20210929170405.1.I078b98ee7727f9ae9d6df8262bad7e325e40faf0@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e1fc1553cd ]
Intel PMU MSRs is in msrs_to_save_all[], so add AMD PMU MSRs to have a
consistent behavior between Intel and AMD when using KVM_GET_MSRS,
KVM_SET_MSRS or KVM_GET_MSR_INDEX_LIST.
We have to add legacy and new MSRs to handle guests running without
X86_FEATURE_PERFCTR_CORE.
Signed-off-by: Fares Mehanna <faresx@amazon.de>
Message-Id: <20210915133951.22389-1-faresx@amazon.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae232ea460 ]
grow_halt_poll_ns() ignores values between 0 and
halt_poll_ns_grow_start (10000 by default). However,
when we shrink halt_poll_ns we may fall way below
halt_poll_ns_grow_start and endup with halt_poll_ns
values that don't make a lot of sense: like 1 or 9,
or 19.
VCPU1 trace (halt_poll_ns_shrink equals 2):
VCPU1 grow 10000
VCPU1 shrink 5000
VCPU1 shrink 2500
VCPU1 shrink 1250
VCPU1 shrink 625
VCPU1 shrink 312
VCPU1 shrink 156
VCPU1 shrink 78
VCPU1 shrink 39
VCPU1 shrink 19
VCPU1 shrink 9
VCPU1 shrink 4
Mirror what grow_halt_poll_ns() does and set halt_poll_ns
to 0 as soon as new shrink-ed halt_poll_ns value falls
below halt_poll_ns_grow_start.
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210902031100.252080-1-senozhatsky@chromium.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 01f91acb55 ]
The SMC64 calling convention passes a function identifier in w0 and its
parameters in x1-x17. Given this, there are two deviations in the
SMC64 call performed by the steal_time test: the function identifier is
assigned to a 64 bit register and the parameter is only 32 bits wide.
Align the call with the SMCCC by using a 32 bit register to handle the
function identifier and increasing the parameter width to 64 bits.
Suggested-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Oliver Upton <oupton@google.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-Id: <20210921171121.2148982-3-oupton@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ebaeab2fe8 ]
Idle page tracking can also be used for process address space, not only
file mappings.
Without this change, using with '-i' option for process address space
encounters below errors reported.
$ sudo ./page-types -p $(pidof bash) -i
mark page idle: Bad file descriptor
mark page idle: Bad file descriptor
mark page idle: Bad file descriptor
mark page idle: Bad file descriptor
...
Link: https://lkml.kernel.org/r/20210917032826.10669-1-changbin.du@gmail.com
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b06d893ef2 ]
Address warning:
fs/smbfs_client/smb2pdu.c:2425 create_sd_buf()
warn: struct type mismatch 'smb3_acl vs cifs_acl'
Pointed out by Dan Carpenter via smatch code analysis tool
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b78f26926b ]
Geert reported that the GIC driver locks up on a Renesas system
since 005c34ae4b ("irqchip/gic: Atomically update affinity")
fixed the driver to use writeb_relaxed() instead of writel_relaxed().
As it turns out, the interconnect used on this system mandates
32bit wide accesses for all MMIO transactions, even if the GIC
architecture specifically mandates for some registers to be byte
accessible. Gahhh...
Work around the issue by crudly detecting the offending system,
and falling back to an inefficient RMW+lock implementation.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/CAMuHMdV+Ev47K5NO8XHsanSq5YRMCHn2gWAQyV-q2LpJVy9HiQ@mail.gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fbdac19e64 ]
Setting SCSI logging level with error=3, we saw some errors from enclosues:
[108017.360833] ses 0:0:9:0: tag#641 Done: NEEDS_RETRY Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK cmd_age=0s
[108017.360838] ses 0:0:9:0: tag#641 CDB: Receive Diagnostic 1c 01 01 00 20 00
[108017.427778] ses 0:0:9:0: Power-on or device reset occurred
[108017.427784] ses 0:0:9:0: tag#641 Done: SUCCESS Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=0s
[108017.427788] ses 0:0:9:0: tag#641 CDB: Receive Diagnostic 1c 01 01 00 20 00
[108017.427791] ses 0:0:9:0: tag#641 Sense Key : Unit Attention [current]
[108017.427793] ses 0:0:9:0: tag#641 Add. Sense: Bus device reset function occurred
[108017.427801] ses 0:0:9:0: Failed to get diagnostic page 0x1
[108017.427804] ses 0:0:9:0: Failed to bind enclosure -19
[108017.427895] ses 0:0:10:0: Attached Enclosure device
[108017.427942] ses 0:0:10:0: Attached scsi generic sg18 type 13
Retry if the Send/Receive Diagnostic commands complete with a transient
error status (NOT_READY or UNIT_ATTENTION with ASC 0x29).
Link: https://lore.kernel.org/r/1631849061-10210-2-git-send-email-wenxiong@linux.ibm.com
Reviewed-by: Brian King <brking@linux.ibm.com>
Reviewed-by: James Bottomley <jejb@linux.ibm.com>
Signed-off-by: Wen Xiong <wenxiong@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5445dae29 ]
To avoid race between time out and tear down, in tear down process,
first we quiesce the queue, and then delete the timer and cancel
the time out work for the queue.
This patch merges the admin and io sync ops into the queue teardown logic
as shown in the RDMA patch 3017013dcc "nvme-rdma: avoid race between time
out and tear down". There is no teardown_lock in nvme-fc.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Tested-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 555f66d0f8 ]
In case the number of hardware queues changes, we need to update the
tagset and the mapping of ctx to hctx first.
If we try to create and connect the I/O queues first, this operation
will fail (target will reject the connect call due to the wrong number
of queues) and hence we bail out of the recreate function. Then we
will to try the very same operation again, thus we don't make any
progress.
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39a71f712d ]
Fix get_warnings_count() to check fscanf() return value to get rid
of the following warning:
x86_64/mmio_warning_test.c: In function ‘get_warnings_count’:
x86_64/mmio_warning_test.c:85:2: warning: ignoring return value of ‘fscanf’ declared with attribute ‘warn_unused_result’ [-Wunused-result]
85 | fscanf(f, "%d", &warnings);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8914a7a247 ]
LKP/0Day reported some building errors about kvm, and errors message
are not always same:
- lib/x86_64/processor.c:1083:31: error: ‘KVM_CAP_NESTED_STATE’ undeclared
(first use in this function); did you mean ‘KVM_CAP_PIT_STATE2’?
- lib/test_util.c:189:30: error: ‘MAP_HUGE_16KB’ undeclared (first use
in this function); did you mean ‘MAP_HUGE_16GB’?
Although kvm relies on the khdr, they still be built in parallel when -j
is specified. In this case, it will cause compiling errors.
Here we mark target khdr as NOTPARALLEL to make it be always built
first.
CC: Philip Li <philip.li@intel.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a5ff77bf0 ]
Couple of fixes to the LBW RR configuration:
1. Add missing configuration of the SM RR registers in the DMA_IF.
2. Remove HBW range that doesn't belong.
3. Add entire gap + DBG area, from end of TPC7 to end of entire
DBG space.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f81c08f897 ]
testusb' application which uses 'usbtest' driver reports 'unknown speed'
from the function 'find_testdev'. The variable 'entry->speed' was not
updated from the application. The IOCTL mentioned in the FIXME comment can
only report whether the connection is low speed or not. Speed is read using
the IOCTL USBDEVFS_GET_SPEED which reports the proper speed grade. The
call is implemented in the function 'handle_testdev' where the file
descriptor was availble locally. Sample output is given below where 'high
speed' is printed as the connected speed.
sudo ./testusb -a
high speed /dev/bus/usb/001/011 0
/dev/bus/usb/001/011 test 0, 0.000015 secs
/dev/bus/usb/001/011 test 1, 0.194208 secs
/dev/bus/usb/001/011 test 2, 0.077289 secs
/dev/bus/usb/001/011 test 3, 0.170604 secs
/dev/bus/usb/001/011 test 4, 0.108335 secs
/dev/bus/usb/001/011 test 5, 2.788076 secs
/dev/bus/usb/001/011 test 6, 2.594610 secs
/dev/bus/usb/001/011 test 7, 2.905459 secs
/dev/bus/usb/001/011 test 8, 2.795193 secs
/dev/bus/usb/001/011 test 9, 8.372651 secs
/dev/bus/usb/001/011 test 10, 6.919731 secs
/dev/bus/usb/001/011 test 11, 16.372687 secs
/dev/bus/usb/001/011 test 12, 16.375233 secs
/dev/bus/usb/001/011 test 13, 2.977457 secs
/dev/bus/usb/001/011 test 14 --> 22 (Invalid argument)
/dev/bus/usb/001/011 test 17, 0.148826 secs
/dev/bus/usb/001/011 test 18, 0.068718 secs
/dev/bus/usb/001/011 test 19, 0.125992 secs
/dev/bus/usb/001/011 test 20, 0.127477 secs
/dev/bus/usb/001/011 test 21 --> 22 (Invalid argument)
/dev/bus/usb/001/011 test 24, 4.133763 secs
/dev/bus/usb/001/011 test 27, 2.140066 secs
/dev/bus/usb/001/011 test 28, 2.120713 secs
/dev/bus/usb/001/011 test 29, 0.507762 secs
Signed-off-by: Faizel K B <faizel.kb@dicortech.com>
Link: https://lore.kernel.org/r/20210902114444.15106-1-faizel.kb@dicortech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 372d1f3e1b ]
The ext2_error() function syncs the filesystem so it sleeps. The caller
is holding a spinlock so it's not allowed to sleep.
ext2_statfs() <- disables preempt
-> ext2_count_free_blocks()
-> ext2_get_group_desc()
Fix this by using WARN() to print an error message and a stack trace
instead of using ext2_error().
Link: https://lore.kernel.org/r/20210921203233.GA16529@kili
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ede7f84c7 ]
When re-entering the main loop of xenvif_tx_check_gop() a 2nd time, the
special considerations for the head of the SKB no longer apply. Don't
mistakenly report ERROR to the frontend for the first entry in the list,
even if - from all I can tell - this shouldn't matter much as the overall
transmit will need to be considered failed anyway.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf9579976f ]
MDIO-attached devices might have interrupts and other things that might
need quiesced when we kexec into a new kernel. Things are even more
creepy when those interrupt lines are shared, and in that case it is
absolutely mandatory to disable all interrupt sources.
Moreover, MDIO devices might be DSA switches, and DSA needs its own
shutdown method to unlink from the DSA master, which is a new
requirement that appeared after commit 2f1e8ea726 ("net: dsa: link
interfaces with the DSA master to get rid of lockdep warnings").
So introduce a ->shutdown method in the MDIO device driver structure.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b225baaba ]
When we get an error flushing one device, during a super block commit, we
record the error in the device structure, in the field 'last_flush_error'.
This is used to later check if we should error out the super block commit,
depending on whether the number of flush errors is greater than or equals
to the maximum tolerated device failures for a raid profile.
However if we get a transient device flush error, unmount the filesystem
and later try to mount it, we can fail the mount because we treat that
past error as critical and consider the device is missing. Even if it's
very likely that the error will happen again, as it's probably due to a
hardware related problem, there may be cases where the error might not
happen again. One example is during testing, and a test case like the
new generic/648 from fstests always triggers this. The test cases
generic/019 and generic/475 also trigger this scenario, but very
sporadically.
When this happens we get an error like this:
$ mount /dev/sdc /mnt
mount: /mnt wrong fs type, bad option, bad superblock on /dev/sdc, missing codepage or helper program, or other error.
$ dmesg
(...)
[12918.886926] BTRFS warning (device sdc): chunk 13631488 missing 1 devices, max tolerance is 0 for writable mount
[12918.888293] BTRFS warning (device sdc): writable mount is not allowed due to too many missing devices
[12918.890853] BTRFS error (device sdc): open_ctree failed
The failure happens because when btrfs_check_rw_degradable() is called at
mount time, or at remount from RO to RW time, is sees a non zero value in
a device's ->last_flush_error attribute, and therefore considers that the
device is 'missing'.
Fix this by setting a device's ->last_flush_error to zero when we close a
device, making sure the error is not seen on the next mount attempt. We
only need to track flush errors during the current mount, so that we never
commit a super block if such errors happened.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bbc9a6eb5e ]
There is a BUG_ON() in btrfs_csum_one_bio() to catch code logic error.
It has indeed caught several bugs during subpage development.
But the BUG_ON() itself will bring down the whole system which is
an overkill.
Replace it with a WARN() and exit gracefully, so that it won't crash the
whole system while we can still catch the code logic error.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02579b2ff8 ]
When the back channel enters SEQ4_STATUS_CB_PATH_DOWN state, the client
recovers by sending BIND_CONN_TO_SESSION but the server fails to recover
the back channel and leaves it as NFSD4_CB_DOWN.
Fix by enhancing nfsd4_bind_conn_to_session to probe the back channel
by calling nfsd4_probe_callback.
Signed-off-by: Dai Ngo <dai.ngo@oracle.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 196159d278 ]
Add info for getting the firmware directly from the UEFI for the Chuwi Hi10
Plus (CWI527), so that the user does not need to manually install the
firmware in /lib/firmware/silead.
This change will make the touchscreen on these devices work OOTB,
without requiring any manual setup.
Also tweak the min and width/height values a bit for more accurate position
reporting.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210905130210.32810-2-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3bf1669b0e ]
Add touchscreen info for the Chuwi HiBook (CWI514) tablet. This includes
info for getting the firmware directly from the UEFI, so that the user does
not need to manually install the firmware in /lib/firmware/silead.
This change will make the touchscreen on these devices work OOTB,
without requiring any manual setup.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210905130210.32810-1-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5457773ef9 ]
Previously zero length transfers submitted to the Rokchip SPI driver would
time out in the SPI layer. This happens because the SPI peripheral does
not trigger a transfer completion interrupt for zero length transfers.
Fix that by completing zero length transfers immediately at start of
transfer.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Link: https://lore.kernel.org/r/20210827050357.165409-1-t.schramm@manjaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
This is a copy of the code and approach from our DAC+ driver.
It allows to probe (and activate) an optional TPA6130A2 headphone
amplifier. Updated email address.
Signed-off-by: Joerg Schambacher <joerg@hifiberry.com>
This is a copy of the approach from our DAC+ driver.
It allows to probe (and activate) an optional TPA6130A2 headphone
amplifier.
Signed-off-by: Joerg Schambacher <joerg@hifiberry.com>
commit e9edc188fc upstream.
Syzbot was able to trigger the following warning [1]
No repro found by syzbot yet but I was able to trigger similar issue
by having 2 scripts running in parallel, changing conntrack hash sizes,
and:
for j in `seq 1 1000` ; do unshare -n /bin/true >/dev/null ; done
It would take more than 5 minutes for net_namespace structures
to be cleaned up.
This is because nf_ct_iterate_cleanup() has to restart everytime
a resize happened.
By adding a mutex, we can serialize hash resizes and cleanups
and also make get_next_corpse() faster by skipping over empty
buckets.
Even without resizes in the picture, this patch considerably
speeds up network namespace dismantles.
[1]
INFO: task syz-executor.0:8312 can't die for more than 144 seconds.
task:syz-executor.0 state:R running task stack:25672 pid: 8312 ppid: 6573 flags:0x00004006
Call Trace:
context_switch kernel/sched/core.c:4955 [inline]
__schedule+0x940/0x26f0 kernel/sched/core.c:6236
preempt_schedule_common+0x45/0xc0 kernel/sched/core.c:6408
preempt_schedule_thunk+0x16/0x18 arch/x86/entry/thunk_64.S:35
__local_bh_enable_ip+0x109/0x120 kernel/softirq.c:390
local_bh_enable include/linux/bottom_half.h:32 [inline]
get_next_corpse net/netfilter/nf_conntrack_core.c:2252 [inline]
nf_ct_iterate_cleanup+0x15a/0x450 net/netfilter/nf_conntrack_core.c:2275
nf_conntrack_cleanup_net_list+0x14c/0x4f0 net/netfilter/nf_conntrack_core.c:2469
ops_exit_list+0x10d/0x160 net/core/net_namespace.c:171
setup_net+0x639/0xa30 net/core/net_namespace.c:349
copy_net_ns+0x319/0x760 net/core/net_namespace.c:470
create_new_namespaces+0x3f6/0xb20 kernel/nsproxy.c:110
unshare_nsproxy_namespaces+0xc1/0x1f0 kernel/nsproxy.c:226
ksys_unshare+0x445/0x920 kernel/fork.c:3128
__do_sys_unshare kernel/fork.c:3202 [inline]
__se_sys_unshare kernel/fork.c:3200 [inline]
__x64_sys_unshare+0x2d/0x40 kernel/fork.c:3200
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f63da68e739
RSP: 002b:00007f63d7c05188 EFLAGS: 00000246 ORIG_RAX: 0000000000000110
RAX: ffffffffffffffda RBX: 00007f63da792f80 RCX: 00007f63da68e739
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000040000000
RBP: 00007f63da6e8cc4 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f63da792f80
R13: 00007fff50b75d3f R14: 00007f63d7c05300 R15: 0000000000022000
Showing all locks held in the system:
1 lock held by khungtaskd/27:
#0: ffffffff8b980020 (rcu_read_lock){....}-{1:2}, at: debug_show_all_locks+0x53/0x260 kernel/locking/lockdep.c:6446
2 locks held by kworker/u4:2/153:
#0: ffff888010c69138 ((wq_completion)events_unbound){+.+.}-{0:0}, at: arch_atomic64_set arch/x86/include/asm/atomic64_64.h:34 [inline]
#0: ffff888010c69138 ((wq_completion)events_unbound){+.+.}-{0:0}, at: arch_atomic_long_set include/linux/atomic/atomic-long.h:41 [inline]
#0: ffff888010c69138 ((wq_completion)events_unbound){+.+.}-{0:0}, at: atomic_long_set include/linux/atomic/atomic-instrumented.h:1198 [inline]
#0: ffff888010c69138 ((wq_completion)events_unbound){+.+.}-{0:0}, at: set_work_data kernel/workqueue.c:634 [inline]
#0: ffff888010c69138 ((wq_completion)events_unbound){+.+.}-{0:0}, at: set_work_pool_and_clear_pending kernel/workqueue.c:661 [inline]
#0: ffff888010c69138 ((wq_completion)events_unbound){+.+.}-{0:0}, at: process_one_work+0x896/0x1690 kernel/workqueue.c:2268
#1: ffffc9000140fdb0 ((kfence_timer).work){+.+.}-{0:0}, at: process_one_work+0x8ca/0x1690 kernel/workqueue.c:2272
1 lock held by systemd-udevd/2970:
1 lock held by in:imklog/6258:
#0: ffff88807f970ff0 (&f->f_pos_lock){+.+.}-{3:3}, at: __fdget_pos+0xe9/0x100 fs/file.c:990
3 locks held by kworker/1:6/8158:
1 lock held by syz-executor.0/8312:
2 locks held by kworker/u4:13/9320:
1 lock held by syz-executor.5/10178:
1 lock held by syz-executor.4/10217:
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7661809d49 upstream.
'kvmalloc()' is a convenience function for people who want to do a
kmalloc() but fall back on vmalloc() if there aren't enough physically
contiguous pages, or if the allocation is larger than what kmalloc()
supports.
However, let's make sure it doesn't get _too_ easy to do crazy things
with it. In particular, don't allow big allocations that could be due
to integer overflow or underflow. So make sure the allocation size fits
in an 'int', to protect against trivial integer conversion issues.
Acked-by: Willy Tarreau <w@1wt.eu>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 505d9dcb0f upstream.
There are three bugs in this code:
1) If we ccp_init_data() fails for &src then we need to free aad.
Use goto e_aad instead of goto e_ctx.
2) The label to free the &final_wa was named incorrectly as "e_tag" but
it should have been "e_final_wa". One error path leaked &final_wa.
3) The &tag was leaked on one error path. In that case, I added a free
before the goto because the resource was local to that block.
Fixes: 36cf515b9b ("crypto: ccp - Enable support for AES GCM on v5 CCPs")
Reported-by: "minihanshen(沈明航)" <minihanshen@tencent.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: John Allen <john.allen@amd.com>
Tested-by: John Allen <john.allen@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dcb713d53e upstream.
There are two invocation sites of hso_free_net_device. After
refactoring hso_create_net_device, this parameter is useless.
Remove the bailout in the hso_free_net_device and change the invocation
sites of this function.
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[Backport this cleanup patch to 5.10 and 5.14 in order to keep the
codebase consistent with the 4.14/4.19/5.4 patchseries]
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a9f5970767 upstream.
up->corkflag field can be read or written without any lock.
Annotate accesses to avoid possible syzbot/KCSAN reports.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22d65765f2 upstream.
Since the actual_length calculation is performed unsigned, packets
shorter than 7 bytes (e.g. packets without data or otherwise truncated)
or non-received packets ("zero" bytes) can cause buffer overflow.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=214437
Fixes: 42337b9d4d958("HID: add driver for U2F Zero built-in LED and RNG")
Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42cb447410 upstream.
When ext4_htree_fill_tree() fails, ext4_dx_readdir() can run into an
infinite loop since if info->last_pos != ctx->pos this will reset the
directory scan and reread the failing entry. For example:
1. a dx_dir which has 3 block, block 0 as dx_root block, block 1/2 as
leaf block which own the ext4_dir_entry_2
2. block 1 read ok and call_filldir which will fill the dirent and update
the ctx->pos
3. block 2 read fail, but we has already fill some dirent, so we will
return back to userspace will a positive return val(see ksys_getdents64)
4. the second ext4_dx_readdir will reset the world since info->last_pos
!= ctx->pos, and will also init the curr_hash which pos to block 1
5. So we will read block1 too, and once block2 still read fail, we can
only fill one dirent because the hash of the entry in block1(besides
the last one) won't greater than curr_hash
6. this time, we forget update last_pos too since the read for block2
will fail, and since we has got the one entry, ksys_getdents64 can
return success
7. Latter we will trapped in a loop with step 4~6
Cc: stable@kernel.org
Signed-off-by: yangerkun <yangerkun@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Link: https://lore.kernel.org/r/20210914111415.3921954-1-yangerkun@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1fd95c05d8 upstream.
If the call to ext4_map_blocks() fails due to an corrupted file
system, ext4_ext_replay_set_iblocks() can get stuck in an infinite
loop. This could be reproduced by running generic/526 with a file
system that has inline_data and fast_commit enabled. The system will
repeatedly log to the console:
EXT4-fs warning (device dm-3): ext4_block_to_path:105: block 1074800922 > max in inode 131076
and the stack that it gets stuck in is:
ext4_block_to_path+0xe3/0x130
ext4_ind_map_blocks+0x93/0x690
ext4_map_blocks+0x100/0x660
skip_hole+0x47/0x70
ext4_ext_replay_set_iblocks+0x223/0x440
ext4_fc_replay_inode+0x29e/0x3b0
ext4_fc_replay+0x278/0x550
do_one_pass+0x646/0xc10
jbd2_journal_recover+0x14a/0x270
jbd2_journal_load+0xc4/0x150
ext4_load_journal+0x1f3/0x490
ext4_fill_super+0x22d4/0x2c00
With this patch, generic/526 still fails, but system is no longer
locking up in a tight loop. It's likely the root casue is that
fast_commit replay is corrupting file systems with inline_data, and we
probably need to add better error handling in the fast commit replay
code path beyond what is done here, which essentially just breaks the
infinite loop without reporting the to the higher levels of the code.
Fixes: 8016E29F4362 ("ext4: fast commit recovery path")
Cc: stable@kernel.org
Cc: Harshad Shirwadkar <harshadshirwadkar@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6fed83957f upstream.
When ext4_insert_delayed block receives and recovers from an error from
ext4_es_insert_delayed_block(), e.g., ENOMEM, it does not release the
space it has reserved for that block insertion as it should. One effect
of this bug is that s_dirtyclusters_counter is not decremented and
remains incorrectly elevated until the file system has been unmounted.
This can result in premature ENOSPC returns and apparent loss of free
space.
Another effect of this bug is that
/sys/fs/ext4/<dev>/delayed_allocation_blocks can remain non-zero even
after syncfs has been executed on the filesystem.
Besides, add check for s_dirtyclusters_counter when inode is going to be
evicted and freed. s_dirtyclusters_counter can still keep non-zero until
inode is written back in .evict_inode(), and thus the check is delayed
to .destroy_inode().
Fixes: 51865fda28 ("ext4: let ext4 maintain extent status tree")
Cc: stable@kernel.org
Suggested-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Jeffle Xu <jefflexu@linux.alibaba.com>
Reviewed-by: Eric Whitney <enwlinux@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Link: https://lore.kernel.org/r/20210823061358.84473-1-jefflexu@linux.alibaba.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a2c2f0826e upstream.
Now EXT4_FC_TAG_ADD_RANGE uses ext4_extent to track the
newly-added blocks, but the limit on the max value of
ee_len field is ignored, and it can lead to BUG_ON as
shown below when running command "fallocate -l 128M file"
on a fast_commit-enabled fs:
kernel BUG at fs/ext4/ext4_extents.h:199!
invalid opcode: 0000 [#1] SMP PTI
CPU: 3 PID: 624 Comm: fallocate Not tainted 5.14.0-rc6+ #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996)
RIP: 0010:ext4_fc_write_inode_data+0x1f3/0x200
Call Trace:
? ext4_fc_write_inode+0xf2/0x150
ext4_fc_commit+0x93b/0xa00
? ext4_fallocate+0x1ad/0x10d0
ext4_sync_file+0x157/0x340
? ext4_sync_file+0x157/0x340
vfs_fsync_range+0x49/0x80
do_fsync+0x3d/0x70
__x64_sys_fsync+0x14/0x20
do_syscall_64+0x3b/0xc0
entry_SYSCALL_64_after_hwframe+0x44/0xae
Simply fixing it by limiting the number of blocks
in one EXT4_FC_TAG_ADD_RANGE TLV.
Fixes: aa75f4d3da ("ext4: main fast-commit commit path")
Cc: stable@kernel.org
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Link: https://lore.kernel.org/r/20210820044505.474318-1-houtao1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 75ca6ad408 upstream.
We should use unsigned long long rather than loff_t to avoid
overflow in ext4_max_bitmap_size() for comparison before returning.
w/o this patch sbi->s_bitmap_maxbytes was becoming a negative
value due to overflow of upper_limit (with has_huge_files as true)
Below is a quick test to trigger it on a 64KB pagesize system.
sudo mkfs.ext4 -b 65536 -O ^has_extents,^64bit /dev/loop2
sudo mount /dev/loop2 /mnt
sudo echo "hello" > /mnt/hello -> This will error out with
"echo: write error: File too large"
Signed-off-by: Ritesh Harjani <riteshh@linux.ibm.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Link: https://lore.kernel.org/r/594f409e2c543e90fd836b78188dfa5c575065ba.1622867594.git.riteshh@linux.ibm.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a89936cce8 upstream.
The tty driver name is used also after registering the driver and must
specifically not be allocated on the stack to avoid leaking information
to user space (or triggering an oops).
Drivers should not try to encode topology information in the tty device
name but this one snuck in through staging without anyone noticing and
another driver has since copied this malpractice.
Fixing the ABI is a separate issue, but this at least plugs the security
hole.
Fixes: ba4dc61fe8 ("Staging: ipack: add support for IP-OCTAL mezzanine board")
Cc: stable@vger.kernel.org # 3.5
Acked-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210917114622.5412-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b2f72cc0a upstream.
In commit b212921b13 ("elf: don't use MAP_FIXED_NOREPLACE for elf
executable mappings") we still leave MAP_FIXED_NOREPLACE in place for
load_elf_interp.
Unfortunately, this will cause kernel to fail to start with:
1 (init): Uhuuh, elf segment at 00003ffff7ffd000 requested but the memory is mapped already
Failed to execute /init (error -17)
The reason is that the elf interpreter (ld.so) has overlapping segments.
readelf -l ld-2.31.so
Program Headers:
Type Offset VirtAddr PhysAddr
FileSiz MemSiz Flags Align
LOAD 0x0000000000000000 0x0000000000000000 0x0000000000000000
0x000000000002c94c 0x000000000002c94c R E 0x10000
LOAD 0x000000000002dae0 0x000000000003dae0 0x000000000003dae0
0x00000000000021e8 0x0000000000002320 RW 0x10000
LOAD 0x000000000002fe00 0x000000000003fe00 0x000000000003fe00
0x00000000000011ac 0x0000000000001328 RW 0x10000
The reason for this problem is the same as described in commit
ad55eac74f ("elf: enforce MAP_FIXED on overlaying elf segments").
Not only executable binaries, elf interpreters (e.g. ld.so) can have
overlapping elf segments, so we better drop MAP_FIXED_NOREPLACE and go
back to MAP_FIXED in load_elf_interp.
Fixes: 4ed2863951 ("fs, elf: drop MAP_FIXED usage from elf_map")
Cc: <stable@vger.kernel.org> # v4.19
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Hocko <mhocko@suse.com>
Signed-off-by: Chen Jingwen <chenjingwen6@huawei.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 35306eb238 ]
Jann Horn reported that SO_PEERCRED and SO_PEERGROUPS implementations
are racy, as af_unix can concurrently change sk_peer_pid and sk_peer_cred.
In order to fix this issue, this patch adds a new spinlock that needs
to be used whenever these fields are read or written.
Jann also pointed out that l2cap_sock_get_peer_pid_cb() is currently
reading sk->sk_peer_pid which makes no sense, as this field
is only possibly set by AF_UNIX sockets.
We will have to clean this in a separate patch.
This could be done by reverting b48596d1dc "Bluetooth: L2CAP: Add get_peer_pid callback"
or implementing what was truly expected.
Fixes: 109f6e39fa ("af_unix: Allow SO_PEERCRED to work across namespaces.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jann Horn <jannh@google.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d88fd1b546 ]
When EEE support was added to the 28nm EPHY it was assumed that it would
be able to support the standard clause 45 over clause 22 register access
method. It turns out that the PHY does not support that, which is the
very reason for using the indirect shadow mode 2 bank 3 access method.
Implement {read,write}_mmd to allow the standard PHY library routines
pertaining to EEE querying and configuration to work correctly on these
PHYs. This forces us to implement a __phy_set_clr_bits() function that
does not grab the MDIO bus lock since the PHY driver's {read,write}_mmd
functions are always called with that lock held.
Fixes: 83ee102a69 ("net: phy: bcm7xxx: add support for 28nm EPHY")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27bf4af69f ]
Currently, the rx vlan filter will always be disabled before selftest and
be enabled after selftest as the rx vlan filter feature is fixed on in
old device earlier than V3.
However, this feature is not fixed in some new devices and it can be
disabled by user. In this case, it is wrong if rx vlan filter is enabled
after selftest. So fix it.
Fixes: bcc26e8dc4 ("net: hns3: remove unused code in hns3_self_test()")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 108b3c7810 ]
Currently, if function adds an existing unicast mac address, eventhough
driver will not add this address into hardware, but it will return 0 in
function hclge_add_uc_addr_common(). It will cause the state of this
unicast mac address is ACTIVE in driver, but it should be in TO-ADD state.
To fix this problem, function hclge_add_uc_addr_common() returns -EEXIST
if mac address is existing, and delete two error log to avoid printing
them all the time after this modification.
Fixes: 72110b5674 ("net: hns3: return 0 and print warning when hit duplicate MAC")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0472e95ffe ]
HCLGE_FLAG_MQPRIO_ENABLE is supposed to set when enable
multiple TCs with tc mqprio, and HCLGE_FLAG_DCB_ENABLE is
supposed to set when enable multiple TCs with ets. But
the driver mixed the flags when updating the tm configuration.
Furtherly, PFC should be available when HCLGE_FLAG_MQPRIO_ENABLE
too, so remove the unnecessary limitation.
Fixes: 5a5c909174 ("net: hns3: add support for tc mqprio offload")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d78e5b6a67 ]
Bellow HNAE3_DEVICE_VERSION_V3, MAC pause mode just support one
TC, when enabled multiple TCs, force enable PFC mode.
HNAE3_DEVICE_VERSION_V3 can support MAC pause mode on multiple
TCs, so when enable multiple TCs, just keep MAC pause mode,
and enable PFC mode just according to the user settings.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 513e605d7a ]
The ixgbe driver currently generates a NULL pointer dereference with
some machine (online cpus < 63). This is due to the fact that the
maximum value of num_xdp_queues is nr_cpu_ids. Code is in
"ixgbe_set_rss_queues"".
Here's how the problem repeats itself:
Some machine (online cpus < 63), And user set num_queues to 63 through
ethtool. Code is in the "ixgbe_set_channels",
adapter->ring_feature[RING_F_FDIR].limit = count;
It becomes 63.
When user use xdp, "ixgbe_set_rss_queues" will set queues num.
adapter->num_rx_queues = rss_i;
adapter->num_tx_queues = rss_i;
adapter->num_xdp_queues = ixgbe_xdp_queues(adapter);
And rss_i's value is from
f = &adapter->ring_feature[RING_F_FDIR];
rss_i = f->indices = f->limit;
So "num_rx_queues" > "num_xdp_queues", when run to "ixgbe_xdp_setup",
for (i = 0; i < adapter->num_rx_queues; i++)
if (adapter->xdp_ring[i]->xsk_umem)
It leads to panic.
Call trace:
[exception RIP: ixgbe_xdp+368]
RIP: ffffffffc02a76a0 RSP: ffff9fe16202f8d0 RFLAGS: 00010297
RAX: 0000000000000000 RBX: 0000000000000020 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 000000000000001c RDI: ffffffffa94ead90
RBP: ffff92f8f24c0c18 R8: 0000000000000000 R9: 0000000000000000
R10: ffff9fe16202f830 R11: 0000000000000000 R12: ffff92f8f24c0000
R13: ffff9fe16202fc01 R14: 000000000000000a R15: ffffffffc02a7530
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
7 [ffff9fe16202f8f0] dev_xdp_install at ffffffffa89fbbcc
8 [ffff9fe16202f920] dev_change_xdp_fd at ffffffffa8a08808
9 [ffff9fe16202f960] do_setlink at ffffffffa8a20235
10 [ffff9fe16202fa88] rtnl_setlink at ffffffffa8a20384
11 [ffff9fe16202fc78] rtnetlink_rcv_msg at ffffffffa8a1a8dd
12 [ffff9fe16202fcf0] netlink_rcv_skb at ffffffffa8a717eb
13 [ffff9fe16202fd40] netlink_unicast at ffffffffa8a70f88
14 [ffff9fe16202fd80] netlink_sendmsg at ffffffffa8a71319
15 [ffff9fe16202fdf0] sock_sendmsg at ffffffffa89df290
16 [ffff9fe16202fe08] __sys_sendto at ffffffffa89e19c8
17 [ffff9fe16202ff30] __x64_sys_sendto at ffffffffa89e1a64
18 [ffff9fe16202ff38] do_syscall_64 at ffffffffa84042b9
19 [ffff9fe16202ff50] entry_SYSCALL_64_after_hwframe at ffffffffa8c0008c
So I fix ixgbe_max_channels so that it will not allow a setting of queues
to be higher than the num_online_cpus(). And when run to ixgbe_xdp_setup,
take the smaller value of num_rx_queues and num_xdp_queues.
Fixes: 4a9b32f30f ("ixgbe: fix potential RX buffer starvation for AF_XDP")
Signed-off-by: Feng Zhou <zhoufeng.zf@bytedance.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79a7482249 ]
Both cxgb4 and csiostor drivers run on their own independent Physical
Function. But when cxgb4 and csiostor are both being loaded in parallel via
modprobe, there is a race when firmware upgrade is attempted by both the
drivers.
When the cxgb4 driver initiates the firmware upgrade, it halts the firmware
and the chip until upgrade is complete. When the csiostor driver is coming
up in parallel, the firmware mailbox communication fails with timeouts and
the csiostor driver probe fails.
Add a module soft dependency on cxgb4 driver to ensure loading csiostor
triggers cxgb4 to load first when available to avoid the firmware upgrade
race.
Link: https://lore.kernel.org/r/1632759248-15382-1-git-send-email-rahul.lakkireddy@chelsio.com
Fixes: a3667aaed5 ("[SCSI] csiostor: Chelsio FCoE offload driver")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ebc69e897e ]
This reverts commit 2d52c58b9c.
We have had several folks complain that this causes hangs for them, which
is especially problematic as the commit has also hit stable already.
As no resolution seems to be forthcoming right now, revert the patch.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=214503
Fixes: 2d52c58b9c ("block, bfq: honor already-setup queue merges")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51bb08dd04 ]
An object file cannot be built for both loadable module and built-in
use at the same time:
arm-linux-gnueabi-ld: drivers/net/ethernet/micrel/ks8851_common.o: in function `ks8851_probe_common':
ks8851_common.c:(.text+0xf80): undefined reference to `__this_module'
Change the ks8851_common code to be a standalone module instead,
and use Makefile logic to ensure this is built-in if at least one
of its two users is.
Fixes: 797047f875 ("net: ks8851: Implement Parallel bus operations")
Link: https://lore.kernel.org/netdev/20210125121937.3900988-1-arnd@kernel.org/
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d888eaac4f ]
When building bpf selftest with make -j, I'm randomly getting build failures
such as this one:
In file included from progs/bpf_flow.c:19:
[...]/tools/testing/selftests/bpf/tools/include/bpf/bpf_helpers.h:11:10: fatal error: 'bpf_helper_defs.h' file not found
#include "bpf_helper_defs.h"
^~~~~~~~~~~~~~~~~~~
The file that fails the build varies between runs but it's always in the
progs/ subdir.
The reason is a missing make dependency on libbpf for the .o files in
progs/. There was a dependency before commit 3ac2e20fba but that commit
removed it to prevent unneeded rebuilds. However, that only works if libbpf
has been built already; the 'wildcard' prerequisite does not trigger when
there's no bpf_helper_defs.h generated yet.
Keep the libbpf as an order-only prerequisite to satisfy both goals. It is
always built before the progs/ objects but it does not trigger unnecessary
rebuilds by itself.
Fixes: 3ac2e20fba ("selftests/bpf: BPF object files should depend only on libbpf headers")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/ee84ab66436fba05a197f952af23c98d90eb6243.1632758415.git.jbenc@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a98ae12fb ]
When introducing CAP_BPF, bpf_jit_charge_modmem() was not changed to treat
programs with CAP_BPF as privileged for the purpose of JIT memory allocation.
This means that a program without CAP_BPF can block a program with CAP_BPF
from loading a program.
Fix this by checking bpf_capable() in bpf_jit_charge_modmem().
Fixes: 2c78ee898d ("bpf: Implement CAP_BPF")
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210922111153.19843-1-lmb@cloudflare.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51032e6f17 ]
The e100_get_regs function is used to implement a simple register dump
for the e100 device. The data is broken into a couple of MAC control
registers, and then a series of PHY registers, followed by a memory dump
buffer.
The total length of the register dump is defined as (1 + E100_PHY_REGS)
* sizeof(u32) + sizeof(nic->mem->dump_buf).
The logic for filling in the PHY registers uses a convoluted inverted
count for loop which counts from E100_PHY_REGS (0x1C) down to 0, and
assigns the slots 1 + E100_PHY_REGS - i. The first loop iteration will
fill in [1] and the final loop iteration will fill in [1 + 0x1C]. This
is actually one more than the supposed number of PHY registers.
The memory dump buffer is then filled into the space at
[2 + E100_PHY_REGS] which will cause that memcpy to assign 4 bytes past
the total size.
The end result is that we overrun the total buffer size allocated by the
kernel, which could lead to a panic or other issues due to memory
corruption.
It is difficult to determine the actual total number of registers
here. The only 8255x datasheet I could find indicates there are 28 total
MDI registers. However, we're reading 29 here, and reading them in
reverse!
In addition, the ethtool e100 register dump interface appears to read
the first PHY register to determine if the device is in MDI or MDIx
mode. This doesn't appear to be documented anywhere within the 8255x
datasheet. I can only assume it must be in register 28 (the extra
register we're reading here).
Lets not change any of the intended meaning of what we copy here. Just
extend the space by 4 bytes to account for the extra register and
continue copying the data out in the same order.
Change the E100_PHY_REGS value to be the correct total (29) so that the
total register dump size is calculated properly. Fix the offset for
where we copy the dump buffer so that it doesn't overrun the total size.
Re-write the for loop to use counting up instead of the convoluted
down-counting. Correct the mdio_read offset to use the 0-based register
offsets, but maintain the bizarre reverse ordering so that we have the
ABI expected by applications like ethtool. This requires and additional
subtraction of 1. It seems a bit odd but it makes the flow of assignment
into the register buffer easier to follow.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Felicitas Hetzelt <felicitashetzelt@gmail.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4329c8dc11 ]
commit abf9b90205 ("e100: cleanup unneeded math") tried to simplify
e100_get_regs_len and remove a double 'divide and then multiply'
calculation that the e100_reg_regs_len function did.
This change broke the size calculation entirely as it failed to account
for the fact that the numbered registers are actually 4 bytes wide and
not 1 byte. This resulted in a significant under allocation of the
register buffer used by e100_get_regs.
Fix this by properly multiplying the register count by u32 first before
adding the size of the dump buffer.
Fixes: abf9b90205 ("e100: cleanup unneeded math")
Reported-by: Felicitas Hetzelt <felicitashetzelt@gmail.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b9c587fed6 ]
Same members of the Marvell Ethernet switches impose MTU restrictions
on ports used for connecting to the CPU or another switch for DSA. If
the MTU is set too low, tagged frames will be discarded. Ensure the
worst case tagger overhead is included in setting the MTU for DSA and
CPU ports.
Fixes: 1baf0fac10 ("net: dsa: mv88e6xxx: Use chip-wide max frame size for MTU")
Reported by: 曹煜 <cao88yu@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b92ce2f54c ]
The MTU passed to the DSA driver is the payload size, typically 1500.
However, the switch uses the frame size when applying restrictions.
Adjust the MTU with the size of the Ethernet header and the frame
checksum. The VLAN header also needs to be included when the frame
size it per port, but not when it is global.
Fixes: 1baf0fac10 ("net: dsa: mv88e6xxx: Use chip-wide max frame size for MTU")
Reported by: 曹煜 <cao88yu@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe23036192 ]
The datasheets suggests the 6161 uses a per port setting for jumbo
frames. Testing has however shown this is not correct, it uses the old
style chip wide MTU control. Change the ops in the 6161 structure to
reflect this.
Fixes: 1baf0fac10 ("net: dsa: mv88e6xxx: Use chip-wide max frame size for MTU")
Reported by: 曹煜 <cao88yu@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c83ff01864 ]
Currently we blow up in trace_dma_fence_init, when calling into
get_driver_name or get_timeline_name, since both the engine and context
might be NULL(or contain some garbage address) in the case of newly
allocated slab objects via the request ctor. Note that we also use
SLAB_TYPESAFE_BY_RCU here, which allows requests to be immediately
freed, but delay freeing the underlying page by an RCU grace period.
With this scheme requests can be re-allocated, at the same time as they
are also being read by some lockless RCU lookup mechanism.
In the ctor case, which is only called for new slab objects(i.e allocate
new page and call the ctor for each object) it's safe to reset the
context/engine prior to calling into dma_fence_init, since we can be
certain that no one is doing an RCU lookup which might depend on peeking
at the engine/context, like in active_engine(), since the object can't
yet be externally visible.
In the recycled case(which might also be externally visible) the request
refcount always transitions from 0->1 after we set the context/engine
etc, which should ensure it's valid to dereference the engine for
example, when doing an RCU list-walk, so long as we can also increment
the refcount first. If the refcount is already zero, then the request is
considered complete/released. If it's non-zero, then the request might
be in the process of being re-allocated, or potentially still in flight,
however after successfully incrementing the refcount, it's possible to
carefully inspect the request state, to determine if the request is
still what we were looking for. Note that all externally visible
requests returned to the cache must have zero refcount.
One possible fix then is to move dma_fence_init out from the request
ctor. Originally this was how it was done, but it was moved in:
commit 855e39e65c
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Feb 3 09:41:48 2020 +0000
drm/i915: Initialise basic fence before acquiring seqno
where it looks like intel_timeline_get_seqno() relied on some of the
rq->fence state, but that is no longer the case since:
commit 12ca695d2c
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Tue Mar 23 16:49:50 2021 +0100
drm/i915: Do not share hwsp across contexts any more, v8.
intel_timeline_get_seqno() could also be cleaned up slightly by dropping
the request argument.
Moving dma_fence_init back out of the ctor, should ensure we have enough
of the request initialised in case of trace_dma_fence_init.
Functionally this should be the same, and is effectively what we were
already open coding before, except now we also assign the fence->lock
and fence->ops, but since these are invariant for recycled
requests(which might be externally visible), and will therefore already
hold the same value, it shouldn't matter.
An alternative fix, since we don't yet have a fully initialised request
when in the ctor, is just setting the context/engine as NULL, but this
does require adding some extra handling in get_driver_name etc.
v2(Daniel):
- Try to make the commit message less confusing
Fixes: 855e39e65c ("drm/i915: Initialise basic fence before acquiring seqno")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Michael Mason <michael.w.mason@intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921134202.3803151-1-matthew.auld@intel.com
(cherry picked from commit be988eaee1)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ab8a447bc ]
After commit 05b35e7eb9 ("smsc95xx: add phylib support"), link changes
are no longer propagated to usbnet. As a result, rx URB allocation won't
happen until there is a packet sent out first (this might never happen,
e.g. running just ssh server with a static IP). Fix by triggering usbnet
EVENT_LINK_CHANGE.
Fixes: 05b35e7eb9 ("smsc95xx: add phylib support")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 597aa16c78 ]
Multipath RTA_FLOW is embedded in nexthop. Dump it in fib_add_nexthop()
to get the length of rtnexthop correct.
Fixes: b0f6019363 ("ipv4: Refactor nexthop attributes in fib_dump_info")
Signed-off-by: Xiao Liang <shaw.leon@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 325fd36ae7 ]
The enetc phylink .mac_config handler intends to clear the IFMODE field
(bits 1:0) of the PM0_IF_MODE register, but incorrectly clears all the
other fields instead.
For normal operation, the bug was inconsequential, due to the fact that
we write the PM0_IF_MODE register in two stages, first in
phylink .mac_config (which incorrectly cleared out a bunch of stuff),
then we update the speed and duplex to the correct values in
phylink .mac_link_up.
Judging by the code (not tested), it looks like maybe loopback mode was
broken, since this is one of the settings in PM0_IF_MODE which is
incorrectly cleared.
Fixes: c76a97218d ("net: enetc: force the RGMII speed and duplex instead of operating in inband mode")
Reported-by: Pavel Machek (CIP) <pavel@denx.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 540effa7f2 ]
For both local and remote sensors all the supported ICs can report an
"undervoltage lockout" condition which means the conversion wasn't
properly performed due to insufficient power supply voltage and so the
measurement results can't be trusted.
Fixes: 9410700b88 ("hwmon: Add driver for Texas Instruments TMP421/422/423 sensor chips")
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Link: https://lore.kernel.org/r/20210924093011.26083-2-fercerpav@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea1300b9df ]
mptcp_token_get_sock() may return a mptcp socket that is in
a different net namespace than the socket that received the token value.
The mptcp syncookie code path had an explicit check for this,
this moves the test into mptcp_token_get_sock() function.
Eventually token.c should be converted to pernet storage, but
such change is not suitable for net tree.
Fixes: 2c5ebd001d ("mptcp: refactor token container")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7e745f8e9 ]
We should always check if skb_header_pointer's return is NULL before
using it, otherwise it may cause null-ptr-deref, as syzbot reported:
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
RIP: 0010:sctp_rcv_ootb net/sctp/input.c:705 [inline]
RIP: 0010:sctp_rcv+0x1d84/0x3220 net/sctp/input.c:196
Call Trace:
<IRQ>
sctp6_rcv+0x38/0x60 net/sctp/ipv6.c:1109
ip6_protocol_deliver_rcu+0x2e9/0x1ca0 net/ipv6/ip6_input.c:422
ip6_input_finish+0x62/0x170 net/ipv6/ip6_input.c:463
NF_HOOK include/linux/netfilter.h:307 [inline]
NF_HOOK include/linux/netfilter.h:301 [inline]
ip6_input+0x9c/0xd0 net/ipv6/ip6_input.c:472
dst_input include/net/dst.h:460 [inline]
ip6_rcv_finish net/ipv6/ip6_input.c:76 [inline]
NF_HOOK include/linux/netfilter.h:307 [inline]
NF_HOOK include/linux/netfilter.h:301 [inline]
ipv6_rcv+0x28c/0x3c0 net/ipv6/ip6_input.c:297
Fixes: 3acb50c18d ("sctp: delay as much as possible skb_linearize")
Reported-by: syzbot+581aff2ae6b860625116@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 313bbd1990 ]
Thomas explained in https://lore.kernel.org/r/87mtoeb4hb.ffs@tglx
that our handling of the hrtimer here is wrong: If the timer fires
late (e.g. due to vCPU scheduling, as reported by Dmitry/syzbot)
then it tries to actually rearm the timer at the next deadline,
which might be in the past already:
1 2 3 N N+1
| | | ... | |
^ intended to fire here (1)
^ next deadline here (2)
^ actually fired here
The next time it fires, it's later, but will still try to schedule
for the next deadline (now 3), etc. until it catches up with N,
but that might take a long time, causing stalls etc.
Now, all of this is simulation, so we just have to fix it, but
note that the behaviour is wrong even per spec, since there's no
value then in sending all those beacons unaligned - they should be
aligned to the TBTT (1, 2, 3, ... in the picture), and if we're a
bit (or a lot) late, then just resume at that point.
Therefore, change the code to use hrtimer_forward_now() which will
ensure that the next firing of the timer would be at N+1 (in the
picture), i.e. the next interval point after the current time.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Reported-by: syzbot+0e964fad69a9c462bc1e@syzkaller.appspotmail.com
Fixes: 01e59e467e ("mac80211_hwsim: hrtimer beacon")
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210915112936.544f383472eb.I3f9712009027aa09244b65399bf18bf482a8c4f1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe94bac626 ]
In ieee80211_amsdu_aggregate() set a pointer frag_tail point to the
end of skb_shinfo(head)->frag_list, and use it to bind other skb in
the end of this function. But when execute ieee80211_amsdu_aggregate()
->ieee80211_amsdu_realloc_pad()->pskb_expand_head(), the address of
skb_shinfo(head)->frag_list will be changed. However, the
ieee80211_amsdu_aggregate() not update frag_tail after call
pskb_expand_head(). That will cause the second skb can't bind to the
head skb appropriately.So we update the address of frag_tail to fix it.
Fixes: 6e0456b545 ("mac80211: add A-MSDU tx support")
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://lore.kernel.org/r/20210830073240.12736-1-pkshih@realtek.com
[reword comment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6fab7af6b ]
Fan speed minimum can be enforced from sysfs. For example, setting
current fan speed to 20 is used to enforce fan speed to be at 100%
speed, 19 - to be not below 90% speed, etcetera. This feature provides
ability to limit fan speed according to some system wise
considerations, like absence of some replaceable units or high system
ambient temperature.
Request for changing fan minimum speed is configuration request and can
be set only through 'sysfs' write procedure. In this situation value of
argument 'state' is above nominal fan speed maximum.
Return non-zero code in this case to avoid
thermal_cooling_device_stats_update() call, because in this case
statistics update violates thermal statistics table range.
The issues is observed in case kernel is configured with option
CONFIG_THERMAL_STATISTICS.
Here is the trace from KASAN:
[ 159.506659] BUG: KASAN: slab-out-of-bounds in thermal_cooling_device_stats_update+0x7d/0xb0
[ 159.516016] Read of size 4 at addr ffff888116163840 by task hw-management.s/7444
[ 159.545625] Call Trace:
[ 159.548366] dump_stack+0x92/0xc1
[ 159.552084] ? thermal_cooling_device_stats_update+0x7d/0xb0
[ 159.635869] thermal_zone_device_update+0x345/0x780
[ 159.688711] thermal_zone_device_set_mode+0x7d/0xc0
[ 159.694174] mlxsw_thermal_modules_init+0x48f/0x590 [mlxsw_core]
[ 159.700972] ? mlxsw_thermal_set_cur_state+0x5a0/0x5a0 [mlxsw_core]
[ 159.731827] mlxsw_thermal_init+0x763/0x880 [mlxsw_core]
[ 160.070233] RIP: 0033:0x7fd995909970
[ 160.074239] Code: 73 01 c3 48 8b 0d 28 d5 2b 00 f7 d8 64 89 01 48 83 c8 ff c3 66 0f 1f 44 00 00 83 3d 99 2d 2c 00 00 75 10 b8 01 00 00 00 0f 05 <48> 3d 01 f0 ff ..
[ 160.095242] RSP: 002b:00007fff54f5d938 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
[ 160.103722] RAX: ffffffffffffffda RBX: 0000000000000013 RCX: 00007fd995909970
[ 160.111710] RDX: 0000000000000013 RSI: 0000000001906008 RDI: 0000000000000001
[ 160.119699] RBP: 0000000001906008 R08: 00007fd995bc9760 R09: 00007fd996210700
[ 160.127687] R10: 0000000000000073 R11: 0000000000000246 R12: 0000000000000013
[ 160.135673] R13: 0000000000000001 R14: 00007fd995bc8600 R15: 0000000000000013
[ 160.143671]
[ 160.145338] Allocated by task 2924:
[ 160.149242] kasan_save_stack+0x19/0x40
[ 160.153541] __kasan_kmalloc+0x7f/0xa0
[ 160.157743] __kmalloc+0x1a2/0x2b0
[ 160.161552] thermal_cooling_device_setup_sysfs+0xf9/0x1a0
[ 160.167687] __thermal_cooling_device_register+0x1b5/0x500
[ 160.173833] devm_thermal_of_cooling_device_register+0x60/0xa0
[ 160.180356] mlxreg_fan_probe+0x474/0x5e0 [mlxreg_fan]
[ 160.248140]
[ 160.249807] The buggy address belongs to the object at ffff888116163400
[ 160.249807] which belongs to the cache kmalloc-1k of size 1024
[ 160.263814] The buggy address is located 64 bytes to the right of
[ 160.263814] 1024-byte region [ffff888116163400, ffff888116163800)
[ 160.277536] The buggy address belongs to the page:
[ 160.282898] page:0000000012275840 refcount:1 mapcount:0 mapping:0000000000000000 index:0xffff888116167000 pfn:0x116160
[ 160.294872] head:0000000012275840 order:3 compound_mapcount:0 compound_pincount:0
[ 160.303251] flags: 0x200000000010200(slab|head|node=0|zone=2)
[ 160.309694] raw: 0200000000010200 ffffea00046f7208 ffffea0004928208 ffff88810004dbc0
[ 160.318367] raw: ffff888116167000 00000000000a0006 00000001ffffffff 0000000000000000
[ 160.327033] page dumped because: kasan: bad access detected
[ 160.333270]
[ 160.334937] Memory state around the buggy address:
[ 160.356469] >ffff888116163800: fc ..
Fixes: 65afb4c8e7 ("hwmon: (mlxreg-fan) Add support for Mellanox FAN driver")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20210916183151.869427-1-vadimp@nvidia.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca465e1f1f ]
If cma_listen_on_all() fails it leaves the per-device ID still on the
listen_list but the state is not set to RDMA_CM_ADDR_BOUND.
When the cmid is eventually destroyed cma_cancel_listens() is not called
due to the wrong state, however the per-device IDs are still holding the
refcount preventing the ID from being destroyed, thus deadlocking:
task:rping state:D stack: 0 pid:19605 ppid: 47036 flags:0x00000084
Call Trace:
__schedule+0x29a/0x780
? free_unref_page_commit+0x9b/0x110
schedule+0x3c/0xa0
schedule_timeout+0x215/0x2b0
? __flush_work+0x19e/0x1e0
wait_for_completion+0x8d/0xf0
_destroy_id+0x144/0x210 [rdma_cm]
ucma_close_id+0x2b/0x40 [rdma_ucm]
__destroy_id+0x93/0x2c0 [rdma_ucm]
? __xa_erase+0x4a/0xa0
ucma_destroy_id+0x9a/0x120 [rdma_ucm]
ucma_write+0xb8/0x130 [rdma_ucm]
vfs_write+0xb4/0x250
ksys_write+0xb5/0xd0
? syscall_trace_enter.isra.19+0x123/0x190
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Ensure that cma_listen_on_all() atomically unwinds its action under the
lock during error.
Fixes: c80a0c52d8 ("RDMA/cma: Add missing error handling of listen_id")
Link: https://lore.kernel.org/r/20210913093344.17230-1-thomas.liu@ucloud.cn
Signed-off-by: Tao Liu <thomas.liu@ucloud.cn>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2cc74e1ee3 ]
ROCE uses IGMP for Multicast instead of the native Infiniband system where
joins are required in order to post messages on the Multicast group. On
Ethernet one can send Multicast messages to arbitrary addresses without
the need to subscribe to a group.
So ROCE correctly does not send IGMP joins during rdma_join_multicast().
F.e. in cma_iboe_join_multicast() we see:
if (addr->sa_family == AF_INET) {
if (gid_type == IB_GID_TYPE_ROCE_UDP_ENCAP) {
ib.rec.hop_limit = IPV6_DEFAULT_HOPLIMIT;
if (!send_only) {
err = cma_igmp_send(ndev, &ib.rec.mgid,
true);
}
}
} else {
So the IGMP join is suppressed as it is unnecessary.
However no such check is done in destroy_mc(). And therefore leaving a
sendonly multicast group will send an IGMP leave.
This means that the following scenario can lead to a multicast receiver
unexpectedly being unsubscribed from a MC group:
1. Sender thread does a sendonly join on MC group X. No IGMP join
is sent.
2. Receiver thread does a regular join on the same MC Group x.
IGMP join is sent and the receiver begins to get messages.
3. Sender thread terminates and destroys MC group X.
IGMP leave is sent and the receiver no longer receives data.
This patch adds the same logic for sendonly joins to destroy_mc() that is
also used in cma_iboe_join_multicast().
Fixes: ab15c95a17 ("IB/core: Support for CMA multicast join flags")
Link: https://lore.kernel.org/r/alpine.DEB.2.22.394.2109081340540.668072@gentwo.de
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 356ed64991 ]
Currently if a function ptr in struct_ops has a return value, its
caller will get a random return value from it, because the return
value of related BPF_PROG_TYPE_STRUCT_OPS prog is just dropped.
So adding a new flag BPF_TRAMP_F_RET_FENTRY_RET to tell bpf trampoline
to save and return the return value of struct_ops prog if ret_size of
the function ptr is greater than 0. Also restricting the flag to be
used alone.
Fixes: 85d33df357 ("bpf: Introduce BPF_MAP_TYPE_STRUCT_OPS")
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20210914023351.3664499-1-houtao1@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69e73dbfda ]
ip_vs_conn_tab_bits may be provided by the user through the
conn_tab_bits module parameter. If this value is greater than 31, or
less than 0, the shift operator used to derive tab_size causes undefined
behaviour.
Fix this checking ip_vs_conn_tab_bits value to be in the range specified
in ipvs Kconfig. If not, simply use default value.
Fixes: 6f7edb4881 ("IPVS: Allow boot time change of hash size")
Reported-by: Yi Chen <yiche@redhat.com>
Signed-off-by: Andrea Claudi <aclaudi@redhat.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit bc0bdc5afa upstream.
If the state is not idle then rdma_bind_addr() will immediately fail and
no change to global state should happen.
For instance if the state is already RDMA_CM_LISTEN then this will corrupt
the src_addr and would cause the test in cma_cancel_operation():
if (cma_any_addr(cma_src_addr(id_priv)) && !id_priv->cma_dev)
To view a mangled src_addr, eg with a IPv6 loopback address but an IPv4
family, failing the test.
This would manifest as this trace from syzkaller:
BUG: KASAN: use-after-free in __list_add_valid+0x93/0xa0 lib/list_debug.c:26
Read of size 8 at addr ffff8881546491e0 by task syz-executor.1/32204
CPU: 1 PID: 32204 Comm: syz-executor.1 Not tainted 5.12.0-rc8-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:79 [inline]
dump_stack+0x141/0x1d7 lib/dump_stack.c:120
print_address_description.constprop.0.cold+0x5b/0x2f8 mm/kasan/report.c:232
__kasan_report mm/kasan/report.c:399 [inline]
kasan_report.cold+0x7c/0xd8 mm/kasan/report.c:416
__list_add_valid+0x93/0xa0 lib/list_debug.c:26
__list_add include/linux/list.h:67 [inline]
list_add_tail include/linux/list.h:100 [inline]
cma_listen_on_all drivers/infiniband/core/cma.c:2557 [inline]
rdma_listen+0x787/0xe00 drivers/infiniband/core/cma.c:3751
ucma_listen+0x16a/0x210 drivers/infiniband/core/ucma.c:1102
ucma_write+0x259/0x350 drivers/infiniband/core/ucma.c:1732
vfs_write+0x28e/0xa30 fs/read_write.c:603
ksys_write+0x1ee/0x250 fs/read_write.c:658
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xae
Which is indicating that an rdma_id_private was destroyed without doing
cma_cancel_listens().
Instead of trying to re-use the src_addr memory to indirectly create an
any address build one explicitly on the stack and bind to that as any
other normal flow would do.
Link: https://lore.kernel.org/r/0-v1-9fbb33f5e201+2a-cma_listen_jgg@nvidia.com
Cc: stable@vger.kernel.org
Fixes: 732d41c545 ("RDMA/cma: Make the locking for automatic state transition more clear")
Reported-by: syzbot+6bb0528b13611047209c@syzkaller.appspotmail.com
Tested-by: Hao Sun <sunhao.th@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8646e53633 upstream.
Invoke rseq's NOTIFY_RESUME handler when processing the flag prior to
transferring to a KVM guest, which is roughly equivalent to an exit to
userspace and processes many of the same pending actions. While the task
cannot be in an rseq critical section as the KVM path is reachable only
by via ioctl(KVM_RUN), the side effects that apply to rseq outside of a
critical section still apply, e.g. the current CPU needs to be updated if
the task is migrated.
Clearing TIF_NOTIFY_RESUME without informing rseq can lead to segfaults
and other badness in userspace VMMs that use rseq in combination with KVM,
e.g. due to the CPU ID being stale after task migration.
Fixes: 72c3c0fe54 ("x86/kvm: Use generic xfer to guest work function")
Reported-by: Peter Foley <pefoley@google.com>
Bisected-by: Doug Evans <dje@google.com>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210901203030.1292304-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[sean: Resolve benign conflict due to unrelated access_ok() check in 5.10]
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d68bad6d8 upstream.
Windows Server 2022 with Hyper-V role enabled failed to boot on KVM when
enlightened VMCS is advertised. Debugging revealed there are two exposed
secondary controls it is not happy with: SECONDARY_EXEC_ENABLE_VMFUNC and
SECONDARY_EXEC_SHADOW_VMCS. These controls are known to be unsupported,
as there are no corresponding fields in eVMCSv1 (see the comment above
EVMCS1_UNSUPPORTED_2NDEXEC definition).
Previously, commit 31de3d2500 ("x86/kvm/hyper-v: move VMX controls
sanitization out of nested_enable_evmcs()") introduced the required
filtering mechanism for VMX MSRs but for some reason put only known
to be problematic (and not full EVMCS1_UNSUPPORTED_* lists) controls
there.
Note, Windows Server 2022 seems to have gained some sanity check for VMX
MSRs: it doesn't even try to launch a guest when there's something it
doesn't like, nested_evmcs_check_controls() mechanism can't catch the
problem.
Let's be bold this time and instead of playing whack-a-mole just filter out
all unsupported controls from VMX MSRs.
Fixes: 31de3d2500 ("x86/kvm/hyper-v: move VMX controls sanitization out of nested_enable_evmcs()")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20210907163530.110066-1-vkuznets@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f9b68f57c upstream.
KASAN reports the following issue:
BUG: KASAN: stack-out-of-bounds in kvm_make_vcpus_request_mask+0x174/0x440 [kvm]
Read of size 8 at addr ffffc9001364f638 by task qemu-kvm/4798
CPU: 0 PID: 4798 Comm: qemu-kvm Tainted: G X --------- ---
Hardware name: AMD Corporation DAYTONA_X/DAYTONA_X, BIOS RYM0081C 07/13/2020
Call Trace:
dump_stack+0xa5/0xe6
print_address_description.constprop.0+0x18/0x130
? kvm_make_vcpus_request_mask+0x174/0x440 [kvm]
__kasan_report.cold+0x7f/0x114
? kvm_make_vcpus_request_mask+0x174/0x440 [kvm]
kasan_report+0x38/0x50
kasan_check_range+0xf5/0x1d0
kvm_make_vcpus_request_mask+0x174/0x440 [kvm]
kvm_make_scan_ioapic_request_mask+0x84/0xc0 [kvm]
? kvm_arch_exit+0x110/0x110 [kvm]
? sched_clock+0x5/0x10
ioapic_write_indirect+0x59f/0x9e0 [kvm]
? static_obj+0xc0/0xc0
? __lock_acquired+0x1d2/0x8c0
? kvm_ioapic_eoi_inject_work+0x120/0x120 [kvm]
The problem appears to be that 'vcpu_bitmap' is allocated as a single long
on stack and it should really be KVM_MAX_VCPUS long. We also seem to clear
the lower 16 bits of it with bitmap_zero() for no particular reason (my
guess would be that 'bitmap' and 'vcpu_bitmap' variables in
kvm_bitmap_or_dest_vcpus() caused the confusion: while the later is indeed
16-bit long, the later should accommodate all possible vCPUs).
Fixes: 7ee30bc132 ("KVM: x86: deliver KVM IOAPIC scan request to target vCPUs")
Fixes: 9a2ae9f6b6 ("KVM: x86: Zero the IOAPIC scan request dest vCPUs bitmap")
Reported-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210827092516.1027264-7-vkuznets@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 943c15ac1b upstream.
If driver read val value sufficient for
(val & 0x08) && (!(val & 0x80)) && ((val & 0x7) == ((val >> 4) & 0x7))
from device then Null pointer dereference occurs.
(It is possible if tmp = 0b0xyz1xyz, where same literals mean same numbers)
Also lm75[] does not serve a purpose anymore after switching to
devm_i2c_new_dummy_device() in w83791d_detect_subclients().
The patch fixes possible NULL pointer dereference by removing lm75[].
Found by Linux Driver Verification project (linuxtesting.org).
Cc: stable@vger.kernel.org
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Link: https://lore.kernel.org/r/20210921155153.28098-1-lutovinova@ispras.ru
[groeck: Dropped unnecessary continuation lines, fixed multi-line alignment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f36b88173 upstream.
If driver read val value sufficient for
(val & 0x08) && (!(val & 0x80)) && ((val & 0x7) == ((val >> 4) & 0x7))
from device then Null pointer dereference occurs.
(It is possible if tmp = 0b0xyz1xyz, where same literals mean same numbers)
Also lm75[] does not serve a purpose anymore after switching to
devm_i2c_new_dummy_device() in w83791d_detect_subclients().
The patch fixes possible NULL pointer dereference by removing lm75[].
Found by Linux Driver Verification project (linuxtesting.org).
Cc: stable@vger.kernel.org
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Link: https://lore.kernel.org/r/20210921155153.28098-2-lutovinova@ispras.ru
[groeck: Dropped unnecessary continuation lines, fixed multipline alignment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd4d747ef0 upstream.
If driver read tmp value sufficient for
(tmp & 0x08) && (!(tmp & 0x80)) && ((tmp & 0x7) == ((tmp >> 4) & 0x7))
from device then Null pointer dereference occurs.
(It is possible if tmp = 0b0xyz1xyz, where same literals mean same numbers)
Also lm75[] does not serve a purpose anymore after switching to
devm_i2c_new_dummy_device() in w83791d_detect_subclients().
The patch fixes possible NULL pointer dereference by removing lm75[].
Found by Linux Driver Verification project (linuxtesting.org).
Cc: stable@vger.kernel.org
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Link: https://lore.kernel.org/r/20210921155153.28098-3-lutovinova@ispras.ru
[groeck: Dropped unnecessary continuation lines, fixed multi-line alignments]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2938b2978a upstream.
Function i2c_smbus_read_byte_data() can return a negative error number
instead of the data read if I2C transaction failed for whatever reason.
Lack of error checking can lead to serious issues on production
hardware, e.g. errors treated as temperatures produce spurious critical
temperature-crossed-threshold errors in BMC logs for OCP server
hardware. The patch was tested with Mellanox OCP Mezzanine card
emulating TMP421 protocol for temperature sensing which sometimes leads
to I2C protocol error during early boot up stage.
Fixes: 9410700b88 ("hwmon: Add driver for Texas Instruments TMP421/422/423 sensor chips")
Cc: stable@vger.kernel.org
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Link: https://lore.kernel.org/r/20210924093011.26083-1-fercerpav@gmail.com
[groeck: dropped unnecessary line breaks]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 80f6e3080b upstream.
If the file size is almost S64_MAX, the calculated number of Merkle tree
levels exceeds FS_VERITY_MAX_LEVELS, causing FS_IOC_ENABLE_VERITY to
fail. This is unintentional, since as the comment above the definition
of FS_VERITY_MAX_LEVELS states, it is enough for over U64_MAX bytes of
data using SHA-256 and 4K blocks. (Specifically, 4096*128**8 >= 2**64.)
The bug is actually that when the number of blocks in the first level is
calculated from i_size, there is a signed integer overflow due to i_size
being signed. Fix this by treating i_size as unsigned.
This was found by the new test "generic: test fs-verity EFBIG scenarios"
(https://lkml.kernel.org/r/b1d116cd4d0ea74b9cd86f349c672021e005a75c.1631558495.git.boris@bur.io).
This didn't affect ext4 or f2fs since those have a smaller maximum file
size, but it did affect btrfs which allows files up to S64_MAX bytes.
Reported-by: Boris Burkov <boris@bur.io>
Fixes: 3fda4c617e ("fs-verity: implement FS_IOC_ENABLE_VERITY ioctl")
Fixes: fd2d1acfca ("fs-verity: add the hook for file ->open()")
Cc: <stable@vger.kernel.org> # v5.4+
Reviewed-by: Boris Burkov <boris@bur.io>
Link: https://lore.kernel.org/r/20210916203424.113376-1-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f060db9937 upstream.
When ACPI NFIT table is failing to populate correct numa information
on arm64, dax_kmem will get NUMA_NO_NODE from the NFIT driver.
Without this patch, pmem can't be probed as RAM devices on arm64 guest:
$ndctl create-namespace -fe namespace0.0 --mode=devdax --map=dev -s 1g -a 128M
kmem dax0.0: rejecting DAX region [mem 0x240400000-0x2bfffffff] with invalid node: -1
kmem: probe of dax0.0 failed with error -22
Suggested-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jia He <justin.he@arm.com>
Cc: <stable@vger.kernel.org>
Fixes: c221c0b030 ("device-dax: "Hotplug" persistent memory for use like normal RAM")
Link: https://lore.kernel.org/r/20210922152919.6940-1-justin.he@arm.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad7cc2d41b upstream.
This patch initializes and enables speaker output on the Lenovo Legion 7i
15IMHG05, Yoga 7i 14ITL5/15ITL5, and 13s Gen2 series of laptops using the
HDA verb sequence specific to each model.
Speaker automute is suppressed for the Lenovo Legion 7i 15IMHG05 to avoid
breaking speaker output on resume and when devices are unplugged from its
headphone jack.
Thanks to: Andreas Holzer, Vincent Morel, sycxyc, Max Christian Pohle and
all others that helped.
[ minor coding style fixes by tiwai ]
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=208555
Signed-off-by: Cameron Berkenpas <cam@neo-zeon.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210913212627.339362-1-cam@neo-zeon.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3b0c406124 ]
This issue happens when a userspace program does an ioctl
FBIOPUT_VSCREENINFO passing the fb_var_screeninfo struct
containing only the fields xres, yres, and bits_per_pixel
with values.
If this struct is the same as the previous ioctl, the
vc_resize() detects it and doesn't call the resize_screen(),
leaving the fb_var_screeninfo incomplete. And this leads to
the updatescrollmode() calculates a wrong value to
fbcon_display->vrows, which makes the real_y() return a
wrong value of y, and that value, eventually, causes
the imageblit to access an out-of-bound address value.
To solve this issue I made the resize_screen() be called
even if the screen does not need any resizing, so it will
"fix and fill" the fb_var_screeninfo independently.
Cc: stable <stable@vger.kernel.org> # after 5.15-rc2 is out, give it time to bake
Reported-and-tested-by: syzbot+858dc7a2f7ef07c2c219@syzkaller.appspotmail.com
Signed-off-by: Igor Matheus Andrade Torrente <igormtorrente@gmail.com>
Link: https://lore.kernel.org/r/20210628134509.15895-1-igormtorrente@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d5f6545934 upstream.
In commit b7213ffa0e ("qnx4: avoid stringop-overread errors") I tried
to teach gcc about how the directory entry structure can be two
different things depending on a status flag. It made the code clearer,
and it seemed to make gcc happy.
However, Arnd points to a gcc bug, where despite using two different
members of a union, gcc then gets confused, and uses the size of one of
the members to decide if a string overrun happens. And not necessarily
the rigth one.
End result: with some configurations, gcc-11 will still complain about
the source buffer size being overread:
fs/qnx4/dir.c: In function 'qnx4_readdir':
fs/qnx4/dir.c:76:32: error: 'strnlen' specified bound [16, 48] exceeds source size 1 [-Werror=stringop-overread]
76 | size = strnlen(name, size);
| ^~~~~~~~~~~~~~~~~~~
fs/qnx4/dir.c:26:22: note: source object declared here
26 | char de_name;
| ^~~~~~~
because gcc will get confused about which union member entry is actually
getting accessed, even when the source code is very clear about it. Gcc
internally will have combined two "redundant" pointers (pointing to
different union elements that are at the same offset), and takes the
size checking from one or the other - not necessarily the right one.
This is clearly a gcc bug, but we can work around it fairly easily. The
biggest thing here is the big honking comment about why we do what we
do.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=99578#c6
Reported-and-tested-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c32dfec6c1 upstream.
Some CP2102 do not support event-insertion mode but return no error when
attempting to enable it.
This means that any event escape characters in the input stream will not
be escaped by the device and consequently regular data may be
interpreted as escape sequences and be removed from the stream by the
driver.
The reporter's device has batch number DCL00X etched into it and as
discovered by the SHA2017 Badge team, counterfeit devices with that
marking can be detected by sending malformed vendor requests. [1][2]
Tests confirm that the possibly counterfeit CP2102 returns a single byte
in response to a malformed two-byte part-number request, while an
original CP2102 returns two bytes. Assume that every CP2102 that behaves
this way also does not support event-insertion mode (e.g. cannot report
parity errors).
[1] https://mobile.twitter.com/sha2017badge/status/1167902087289532418
[2] https://hackaday.com/2017/08/14/hands-on-with-the-shacamp-2017-badge/#comment-3903376
Reported-by: Malte Di Donato <malte@neo-soft.org>
Tested-by: Malte Di Donato <malte@neo-soft.org>
Fixes: a7207e9835 ("USB: serial: cp210x: add support for line-status events")
Cc: stable@vger.kernel.org # 5.9
Link: https://lore.kernel.org/r/20210922113100.20888-1-johan@kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b4bd25667 upstream.
After upgrading to Linux 5.13.3 I noticed my laptop would shutdown due
to overheat (when it should not). It turned out this was due to commit
fe6a6de669 ("thermal/drivers/int340x/processor_thermal: Fix tcc setting").
What happens is this drivers uses a global variable to keep track of the
tcc offset (tcc_offset_save) and uses it on resume. The issue is this
variable is initialized to 0, but is only set in
tcc_offset_degree_celsius_store, i.e. when the tcc offset is explicitly
set by userspace. If that does not happen, the resume path will set the
offset to 0 (in my case the h/w default being 3, the offset would become
too low after a suspend/resume cycle).
The issue did not arise before commit fe6a6de669, as the function
setting the offset would return if the offset was 0. This is no longer
the case (rightfully).
Fix this by not applying the offset if it wasn't saved before, reverting
back to the old logic. A better approach will come later, but this will
be easier to apply to stable kernels.
The logic to restore the offset after a resume was there long before
commit fe6a6de669, but as a value of 0 was considered invalid I'm
referencing the commit that made the issue possible in the Fixes tag
instead.
Fixes: fe6a6de669 ("thermal/drivers/int340x/processor_thermal: Fix tcc setting")
Cc: stable@vger.kernel.org
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: Srinivas Pandruvada <srinivas.pI andruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20210909085613.5577-2-atenart@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit efafec27c5 ]
Without CONFIG_PM enabled, the SET_RUNTIME_PM_OPS() macro ends up being
empty, and the only use of tegra_slink_runtime_{resume,suspend} goes
away, resulting in
drivers/spi/spi-tegra20-slink.c:1200:12: error: ‘tegra_slink_runtime_resume’ defined but not used [-Werror=unused-function]
1200 | static int tegra_slink_runtime_resume(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/spi/spi-tegra20-slink.c:1188:12: error: ‘tegra_slink_runtime_suspend’ defined but not used [-Werror=unused-function]
1188 | static int tegra_slink_runtime_suspend(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~
mark the functions __maybe_unused to make the build happy.
This hits the alpha allmodconfig build (and others).
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c0d2a46c0 ]
tx timeout and slot time are currently specified in units of HZ. On
Alpha, HZ is defined as 1024. When building alpha:allmodconfig, this
results in the following error message.
drivers/net/hamradio/6pack.c: In function 'sixpack_open':
drivers/net/hamradio/6pack.c:71:41: error:
unsigned conversion from 'int' to 'unsigned char'
changes value from '256' to '0'
In the 6PACK protocol, tx timeout is specified in units of 10 ms and
transmitted over the wire:
https://www.linux-ax25.org/wiki/6PACK
Defining a value dependent on HZ doesn't really make sense, and
presumably comes from the (very historical) situation where HZ was
originally 100.
Note that the SIXP_SLOTTIME use explicitly is about 10ms granularity:
mod_timer(&sp->tx_t, jiffies + ((when + 1) * HZ) / 100);
and the SIXP_TXDELAY walue is sent as a byte over the wire.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35a3f4ef0a ]
Some drivers pass a pointer to volatile data to virt_to_bus() and
virt_to_phys(), and that works fine. One exception is alpha. This
results in a number of compile errors such as
drivers/net/wan/lmc/lmc_main.c: In function 'lmc_softreset':
drivers/net/wan/lmc/lmc_main.c:1782:50: error:
passing argument 1 of 'virt_to_bus' discards 'volatile'
qualifier from pointer target type
drivers/atm/ambassador.c: In function 'do_loader_command':
drivers/atm/ambassador.c:1747:58: error:
passing argument 1 of 'virt_to_bus' discards 'volatile'
qualifier from pointer target type
Declare the parameter of virt_to_phys and virt_to_bus as pointer to
volatile to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7213ffa0e ]
The qnx4 directory entries are 64-byte blocks that have different
contents depending on the a status byte that is in the last byte of the
block.
In particular, a directory entry can be either a "link info" entry with
a 48-byte name and pointers to the real inode information, or an "inode
entry" with a smaller 16-byte name and the full inode information.
But the code was written to always just treat the directory name as if
it was part of that "inode entry", and just extend the name to the
longer case if the status byte said it was a link entry.
That work just fine and gives the right results, but now that gcc is
tracking data structure accesses much more, the code can trigger a
compiler error about using up to 48 bytes (the long name) in a structure
that only has that shorter name in it:
fs/qnx4/dir.c: In function ‘qnx4_readdir’:
fs/qnx4/dir.c:51:32: error: ‘strnlen’ specified bound 48 exceeds source size 16 [-Werror=stringop-overread]
51 | size = strnlen(de->di_fname, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from fs/qnx4/qnx4.h:3,
from fs/qnx4/dir.c:16:
include/uapi/linux/qnx4_fs.h:45:25: note: source object declared here
45 | char di_fname[QNX4_SHORT_NAME_MAX];
| ^~~~~~~~
which is because the source code doesn't really make this whole "one of
two different types" explicit.
Fix this by introducing a very explicit union of the two types, and
basically explaining to the compiler what is really going on.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc7c028dcd ]
The sparc mdesc code does pointer games with 'struct mdesc_hdr', but
didn't describe to the compiler how that header is then followed by the
data that the header describes.
As a result, gcc is now unhappy since it does stricter pointer range
tracking, and doesn't understand about how these things work. This
results in various errors like:
arch/sparc/kernel/mdesc.c: In function ‘mdesc_node_by_name’:
arch/sparc/kernel/mdesc.c:647:22: error: ‘strcmp’ reading 1 or more bytes from a region of size 0 [-Werror=stringop-overread]
647 | if (!strcmp(names + ep[ret].name_offset, name))
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
which are easily avoided by just describing 'struct mdesc_hdr' better,
and making the node_block() helper function look into that unsized
data[] that follows the header.
This makes the sparc64 build happy again at least for my cross-compiler
version (gcc version 11.2.1).
Link: https://lore.kernel.org/lkml/CAHk-=wi4NW3NC0xWykkw=6LnjQD6D_rtRtxY9g8gQAJXtQMi8A@mail.gmail.com/
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dff2d13114 ]
gcc 11.x reports the following compiler warning/error.
drivers/net/ethernet/i825xx/82596.c: In function 'i82596_probe':
arch/m68k/include/asm/string.h:72:25: error:
'__builtin_memcpy' reading 6 bytes from a region of size 0 [-Werror=stringop-overread]
Use absolute_pointer() to work around the problem.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6b5f1a569 ]
absolute_pointer() disassociates a pointer from its originating symbol
type and context. Use it to prevent compiler warnings/errors such as
drivers/net/ethernet/i825xx/82596.c: In function 'i82596_probe':
arch/m68k/include/asm/string.h:72:25: error:
'__builtin_memcpy' reading 6 bytes from a region of size 0 [-Werror=stringop-overread]
Such warnings may be reported by gcc 11.x for string and memory
operations on fixed addresses.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3df49967f6 ]
When the integrity profile is unregistered there can still be integrity
reads queued up which could see a NULL verify_fn as shown by the race
window below:
CPU0 CPU1
process_one_work nvme_validate_ns
bio_integrity_verify_fn nvme_update_ns_info
nvme_update_disk_info
blk_integrity_unregister
---set queue->integrity as 0
bio_integrity_process
--access bi->profile->verify_fn(bi is a pointer of queue->integity)
Before calling blk_integrity_unregister in nvme_update_disk_info, we must
make sure that there is no work item in the kintegrityd_wq. Just call
blk_flush_integrity to flush the work queue so the bug can be resolved.
Signed-off-by: Lihong Kou <koulihong@huawei.com>
[hch: split up and shortened the changelog]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Link: https://lore.kernel.org/r/20210914070657.87677-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7bbee36d71 ]
In amdgpu_dm_atomic_check, dc_validate_global_state is called. On
failure this logs a warning to the kernel journal. However warnings
shouldn't be used for atomic test-only commit failures: user-space
might be perfoming a lot of atomic test-only commits to find the
best hardware configuration.
Downgrade the log to a regular DRM atomic message. While at it, use
the new device-aware logging infrastructure.
This fixes error messages in the kernel when running gamescope [1].
[1]: https://github.com/Plagman/gamescope/issues/245
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Simon Ser <contact@emersion.fr>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59583f7476 ]
Commit 53b7670e57 ("sparc: factor the dma coherent mapping into
helper") lost the page align for the calls to dma_make_coherent and
srmmu_unmapiorange. The latter cannot handle a non page aligned len
argument.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9817d763db ]
We should always destroy cm_id before destroy qp to avoid to get cma
event after qp was destroyed, which may lead to use after free.
In RDMA connection establishment error flow, don't destroy qp in cm
event handler.Just report cm_error to upper level, qp will be destroy
in nvme_rdma_alloc_queue() after destroy cm id.
Signed-off-by: Ruozhu Li <liruozhu@huawei.com>
Reviewed-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79f528afa9 ]
nvme_update_ana_state() has a deficiency that results in a failure to
properly update the ana state for a namespace in the following case:
NSIDs in ctrl->namespaces: 1, 3, 4
NSIDs in desc->nsids: 1, 2, 3, 4
Loop iteration 0:
ns index = 0, n = 0, ns->head->ns_id = 1, nsid = 1, MATCH.
Loop iteration 1:
ns index = 1, n = 1, ns->head->ns_id = 3, nsid = 2, NO MATCH.
Loop iteration 2:
ns index = 2, n = 2, ns->head->ns_id = 4, nsid = 4, MATCH.
Where the update to the ANA state of NSID 3 is missed. To fix this
increment n and retry the update with the same ns when ns->head->ns_id is
higher than nsid,
Signed-off-by: Anton Eidelman <anton@lightbitslabs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8480ed9c2b ]
Today the Xen ballooning is done via delayed work in a workqueue. This
might result in workqueue hangups being reported in case of large
amounts of memory are being ballooned in one go (here 16GB):
BUG: workqueue lockup - pool cpus=6 node=0 flags=0x0 nice=0 stuck for 64s!
Showing busy workqueues and worker pools:
workqueue events: flags=0x0
pwq 12: cpus=6 node=0 flags=0x0 nice=0 active=2/256 refcnt=3
in-flight: 229:balloon_process
pending: cache_reap
workqueue events_freezable_power_: flags=0x84
pwq 12: cpus=6 node=0 flags=0x0 nice=0 active=1/256 refcnt=2
pending: disk_events_workfn
workqueue mm_percpu_wq: flags=0x8
pwq 12: cpus=6 node=0 flags=0x0 nice=0 active=1/256 refcnt=2
pending: vmstat_update
pool 12: cpus=6 node=0 flags=0x0 nice=0 hung=64s workers=3 idle: 2222 43
This can easily be avoided by using a dedicated kernel thread for doing
the ballooning work.
Reported-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20210827123206.15429-1-jgross@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9a7e9df73 ]
If HWP has been already been enabled by BIOS, it may be
necessary to override some kernel command line parameters.
Once it has been enabled it requires a reset to be disabled.
Suggested-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1a89856fb ]
m68k builds fail widely with errors such as
arch/m68k/include/asm/raw_io.h:20:19: error:
cast to pointer from integer of different size
arch/m68k/include/asm/raw_io.h:30:32: error:
cast to pointer from integer of different size [-Werror=int-to-p
On m68k, io functions are defined as macros. The problem is seen if the
macro parameter variable size differs from the size of a pointer. Cast
the parameter of all io macros to unsigned long before casting it to
a pointer to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210907060729.2391992-1-linux@roeck-us.net
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 67f3b2f822 ]
blk-mq can't run allocating driver tag and updating ->rqs[tag]
atomically, meantime blk-mq doesn't clear ->rqs[tag] after the driver
tag is released.
So there is chance to iterating over one stale request just after the
tag is allocated and before updating ->rqs[tag].
scsi_host_busy_iter() calls scsi_host_check_in_flight() to count scsi
in-flight requests after scsi host is blocked, so no new scsi command can
be marked as SCMD_STATE_INFLIGHT. However, driver tag allocation still can
be run by blk-mq core. One request is marked as SCMD_STATE_INFLIGHT,
but this request may have been kept in another slot of ->rqs[], meantime
the slot can be allocated out but ->rqs[] isn't updated yet. Then this
in-flight request is counted twice as SCMD_STATE_INFLIGHT. This way causes
trouble in handling scsi error.
Fixes the issue by not iterating over stale request.
Cc: linux-scsi@vger.kernel.org
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Reported-by: luojiaxing <luojiaxing@huawei.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20210906065003.439019-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08dad2f4d5 ]
The Synopsys Ethernet IP uses the CSR clock as a base clock for MDC.
The divisor used is set in the MAC_MDIO_Address register field CR
(Clock Rate)
The divisor is there to change the CSR clock into a clock that falls
below the IEEE 802.3 specified max frequency of 2.5MHz.
If the CSR clock is 300MHz, the code falls back to using the reset
value in the MAC_MDIO_Address register, as described in the comment
above this code.
However, 300MHz is actually an allowed value and the proper divider
can be estimated quite easily (it's just 1Hz difference!)
A CSR frequency of 300MHz with the maximum clock rate value of 0x5
(STMMAC_CSR_250_300M, a divisor of 124) gives somewhere around
~2.42MHz which is below the IEEE 802.3 specified maximum.
For the ARTPEC-8 SoC, the CSR clock is this problematic 300MHz,
and unfortunately, the reset-value of the MAC_MDIO_Address CR field
is 0x0.
This leads to a clock rate of zero and a divisor of 42, and gives an
MDC frequency of ~7.14MHz.
Allow CSR clock of 300MHz by making the comparison inclusive.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d82d5303c4 ]
plat_dev->dev->platform_data is released by platform_device_unregister(),
use of pclk and hclk is a use-after-free. Since device unregister won't
need a clk device we adjust the function call sequence to fix this issue.
[ 31.261225] BUG: KASAN: use-after-free in macb_remove+0x77/0xc6 [macb_pci]
[ 31.275563] Freed by task 306:
[ 30.276782] platform_device_release+0x25/0x80
Suggested-by: Nicolas Ferre <Nicolas.Ferre@microchip.com>
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea269a6f72 ]
Currently changes to the advertising state via ethtool do not cause any
reselection of the configured interface mode after the SFP is already
inserted and initially configured.
While it is not typical to change the advertised link modes for an
interface using an SFP in certain use cases it is desirable. In the case
of a SFP port that is capable of handling both SFP and SFP+ modules it
will automatically select between 1G and 10G modes depending on the
supported mode of the SFP. However if the SFP module is capable of
working in multiple modes (e.g. a SFP+ DAC that can operate at 1G or
10G), one end of the cable may be attached to a SFP 1000base-x port thus
the SFP+ end must be manually configured to the 1000base-x mode in order
for the link to be established.
This change causes the ethtool setting of advertised mode changes to
reselect the interface mode so that the link can be established.
Additionally when a module is inserted the advertising mode is reset to
match the supported modes of the module.
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9990da93d2 ]
For each provided buffer, we allocate a struct io_buffer to hold the
data associated with it. As a large number of buffers can be provided,
account that data with memcg.
Fixes: ddf0322db7 ("io_uring: add IORING_OP_PROVIDE_BUFFERS")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c99720b28 ]
Add a missing __iomem annotation to address a sparse warning. The caller
is expected to pass an __iomem annotated pointer to this function. The
current usages send a 64-bytes command descriptor to an MMIO location
(portal) on a device for consumption.
Also, from the comment in movdir64b(), which also applies to enqcmds(),
@__dst must be supplied as an lvalue because this tells the compiler
what the object is (its size) the instruction accesses. I.e., not the
pointers but what they point to, thus the deref'ing '*'."
The actual sparse warning is:
drivers/dma/idxd/submit.c: note: in included file (through arch/x86/include/asm/processor.h, \
arch/x86/include/asm/timex.h, include/linux/timex.h, include/linux/time32.h, \
include/linux/time.h, include/linux/stat.h, ...):
./arch/x86/include/asm/special_insns.h:289:41: warning: incorrect type in initializer (different address spaces)
./arch/x86/include/asm/special_insns.h:289:41: expected struct <noident> *__dst
./arch/x86/include/asm/special_insns.h:289:41: got void [noderef] __iomem *dst
[ bp: Massage commit message. ]
Fixes: 7f5933f81b ("x86/asm: Add an enqcmds() wrapper for the ENQCMDS instruction")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lkml.kernel.org/r/161003789741.4062451.14362269365703761223.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7df835a32a ]
Commit b0140891a8 ("md: Fix race when creating a new md device.")
not only moved assigning mddev->gendisk before calling add_disk, which
fixes the races described in the commit log, but also added a
mddev->open_mutex critical section over add_disk and creation of the
md kobj. Adding a kobject after add_disk is racy vs deleting the gendisk
right after adding it, but md already prevents against that by holding
a mddev->active reference.
On the other hand taking this lock added a lock order reversal with what
is not disk->open_mutex (used to be bdev->bd_mutex when the commit was
added) for partition devices, which need that lock for the internal open
for the partition scan, and a recent commit also takes it for
non-partitioned devices, leading to further lockdep splatter.
Fixes: b0140891a8 ("md: Fix race when creating a new md device.")
Fixes: d626338735 ("block: support delayed holder registration")
Reported-by: syzbot+fadc0aaf497e6a493b9f@syzkaller.appspotmail.com
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: syzbot+fadc0aaf497e6a493b9f@syzkaller.appspotmail.com
Reviewed-by: NeilBrown <neilb@suse.de>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e946d3c887 ]
The problem is the mismatched types between "ctx->total_len" which is
an unsigned int, "rc" which is an int, and "ctx->rc" which is a
ssize_t. The code does:
ctx->rc = (rc == 0) ? ctx->total_len : rc;
We want "ctx->rc" to store the negative "rc" error code. But what
happens is that "rc" is type promoted to a high unsigned int and
'ctx->rc" will store the high positive value instead of a negative
value.
The fix is to change "rc" from an int to a ssize_t.
Fixes: c610c4b619 ("CIFS: Add asynchronous write support through kernel AIO")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1bb30b20b4 ]
After printing the list of thermal governors, then this function prints
a newline character. The problem is that "size" has not been updated
after printing the last governor. This means that it can write one
character (the NUL terminator) beyond the end of the buffer.
Get rid of the "size" variable and just use "PAGE_SIZE - count" directly.
Fixes: 1b4f48494e ("thermal: core: group functions related to governor handling")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210916131342.GB25094@kili
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 298ba0e3d4 ]
Various places in the nvme code that rely on ctrl->namespace to be
ordered. Ensure that the namespae is inserted into the list at the
right position from the start instead of sorting it after the fact.
Fixes: 540c801c65 ("NVMe: Implement namespace list scanning")
Reported-by: Anton Eidelman <anton.eidelman@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e371af033c ]
When the controller sends us multiple r2t PDUs in a single
request we need to account for it correctly as our send/recv
context run concurrently (i.e. we get a new r2t with r2t_offset
before we updated our iterator and req->data_sent marker). This
can cause wrong offsets to be sent to the controller.
To fix that, we will first know that this may happen only in
the send sequence of the last page, hence we will take
the r2t_offset to the h2c PDU data_offset, and in
nvme_tcp_try_send_data loop, we make sure to increment
the request markers also when we completed a PDU but
we are expecting more r2t PDUs as we still did not send
the entire data of the request.
Fixes: 825619b09a ("nvme-tcp: fix possible use-after-completion")
Reported-by: Nowak, Lukasz <Lukasz.Nowak@Dell.com>
Tested-by: Nowak, Lukasz <Lukasz.Nowak@Dell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 34331739e1 ]
Earlier successes leave 'ret' in a non error state, so these errors are
not reported. Set ret to -EINVAL before going to the error handler.
This addresses two issues reported by smatch:
drivers/fpga/machxo2-spi.c:229 machxo2_write_init()
warn: missing error code 'ret'
drivers/fpga/machxo2-spi.c:316 machxo2_write_complete()
warn: missing error code 'ret'
[mdf@kernel.org: Reworded commit message]
Fixes: 88fb3a0023 ("fpga: lattice machxo2: Add Lattice MachXO2 support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06e49073df ]
'set_signals()' in synclink_gt.c conflicts with an exported symbol
in arch/um/, so change set_signals() to set_gtsignals(). Keep
the function names similar by also changing get_signals() to
get_gtsignals().
../drivers/tty/synclink_gt.c:442:13: error: conflicting types for ‘set_signals’
static void set_signals(struct slgt_info *info);
^~~~~~~~~~~
In file included from ../include/linux/irqflags.h:16:0,
from ../include/linux/spinlock.h:58,
from ../include/linux/mm_types.h:9,
from ../include/linux/buildid.h:5,
from ../include/linux/module.h:14,
from ../drivers/tty/synclink_gt.c:46:
../arch/um/include/asm/irqflags.h:6:5: note: previous declaration of ‘set_signals’ was here
int set_signals(int enable);
^~~~~~~~~~~
Fixes: 705b6c7b34 ("[PATCH] new driver synclink_gt")
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20210902003806.17054-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef7ae7f746 ]
Commit 356ba2a8bc ("scsi: target: tcmu: Make pgr_support and alua_support
attributes writable") introduced support for changeable alua_support and
pgr_support target attributes. These can only be changed if the backstore
is user-backed, otherwise the kernel returns -EINVAL.
This triggers a warning in the targetcli/rtslib code when performing a
target restore that includes non-userbacked backstores:
# targetctl restore
Storage Object block/storage1: Cannot set attribute alua_support:
[Errno 22] Invalid argument, skipped
Storage Object block/storage1: Cannot set attribute pgr_support:
[Errno 22] Invalid argument, skipped
Fix this warning by returning an error code only if we are really going to
flip the PGR/ALUA bit in the transport_flags field, otherwise we will do
nothing and return success.
Return ENOSYS instead of EINVAL if the pgr/alua attributes can not be
changed, this way it will be possible for userspace to understand if the
operation failed because an invalid value has been passed to strtobool() or
because the attributes are fixed.
Fixes: 356ba2a8bc ("scsi: target: tcmu: Make pgr_support and alua_support attributes writable")
Link: https://lore.kernel.org/r/20210906151809.52811-1-mlombard@redhat.com
Reviewed-by: Bodo Stroesser <bostroesser@gmail.com>
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d88c339c4 ]
After fixing hibernation resume flow, another usecase was found which
should be explicitly handled - resume when device is in "down" state.
Invoke aq_nic_init jointly with aq_nic_start only if ndev was already
up during suspend/hibernate. We still need to perform nic_deinit() if
caller requests for it, to handle the freeze/resume scenarios.
Fixes: 57f780f1c4 ("atlantic: Fix driver resume flow.")
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fdbccea419 ]
Driver doesn't support aRFS for encapsulated packets, return early error
in such a case.
Fixes: 1eb8c695bd ("net/mlx4_en: Add accelerated RFS support")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ea7812326 ]
If the HW device is during recovery, the HW resources will never return,
hence we shouldn't wait for the CID (HW context ID) bitmaps to clear.
This fix speeds up the error recovery flow.
Fixes: 64515dc899 ("qed: Add infrastructure for error detection and recovery")
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 248f064af2 ]
When qeth_set_online() calls qeth_clear_working_pool_list() to roll
back after an error exit from qeth_hardsetup_card(), we are at risk of
accessing card->qdio.in_q before it was allocated by
qeth_alloc_qdio_queues() via qeth_mpc_initialize().
qeth_clear_working_pool_list() then dereferences NULL, and by writing to
queue->bufs[i].pool_entry scribbles all over the CPU's lowcore.
Resulting in a crash when those lowcore areas are used next (eg. on
the next machine-check interrupt).
Such a scenario would typically happen when the device is first set
online and its queues aren't allocated yet. An early IO error or certain
misconfigs (eg. mismatched transport mode, bad portno) then cause us to
error out from qeth_hardsetup_card() with card->qdio.in_q still being
NULL.
Fix it by checking the pointer for NULL before accessing it.
Note that we also have (rare) paths inside qeth_mpc_initialize() where
a configuration change can cause us to free the existing queues,
expecting that subsequent code will allocate them again. If we then
error out before that re-allocation happens, the same bug occurs.
Fixes: eff73e16ee ("s390/qeth: tolerate pre-filled RX buffer")
Reported-by: Stefan Raspl <raspl@linux.ibm.com>
Root-caused-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e3dbf765f ]
During initialization of a signal testcase, features declared as required
are properly checked against the running system but no action is then taken
to effectively skip such a testcase.
Fix core signals test logic to abort initialization and report such a
testcase as skipped to the KSelfTest framework.
Fixes: f96bf43403 ("kselftest: arm64: mangle_pstate_invalid_compat_toggle and common utils")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210920121228.35368-1-cristian.marussi@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 74b6d7d133 ]
The Linux device model permits both the ->shutdown and ->remove driver
methods to get called during a shutdown procedure. Example: a DSA switch
which sits on an SPI bus, and the SPI bus driver calls this on its
->shutdown method:
spi_unregister_controller
-> device_for_each_child(&ctlr->dev, NULL, __unregister);
-> spi_unregister_device(to_spi_device(dev));
-> device_del(&spi->dev);
So this is a simple pattern which can theoretically appear on any bus,
although the only other buses on which I've been able to find it are
I2C:
i2c_del_adapter
-> device_for_each_child(&adap->dev, NULL, __unregister_client);
-> i2c_unregister_device(client);
-> device_unregister(&client->dev);
The implication of this pattern is that devices on these buses can be
unregistered after having been shut down. The drivers for these devices
might choose to return early either from ->remove or ->shutdown if the
other callback has already run once, and they might choose that the
->shutdown method should only perform a subset of the teardown done by
->remove (to avoid unnecessary delays when rebooting).
So in other words, the device driver may choose on ->remove to not
do anything (therefore to not unregister an MDIO bus it has registered
on ->probe), because this ->remove is actually triggered by the
device_shutdown path, and its ->shutdown method has already run and done
the minimally required cleanup.
This used to be fine until the blamed commit, but now, the following
BUG_ON triggers:
void mdiobus_free(struct mii_bus *bus)
{
/* For compatibility with error handling in drivers. */
if (bus->state == MDIOBUS_ALLOCATED) {
kfree(bus);
return;
}
BUG_ON(bus->state != MDIOBUS_UNREGISTERED);
bus->state = MDIOBUS_RELEASED;
put_device(&bus->dev);
}
In other words, there is an attempt to free an MDIO bus which was not
unregistered. The attempt to free it comes from the devres release
callbacks of the SPI device, which are executed after the device is
unregistered.
I'm not saying that the fact that MDIO buses allocated using devres
would automatically get unregistered wasn't strange. I'm just saying
that the commit didn't care about auditing existing call paths in the
kernel, and now, the following code sequences are potentially buggy:
(a) devm_mdiobus_alloc followed by plain mdiobus_register, for a device
located on a bus that unregisters its children on shutdown. After
the blamed patch, either both the alloc and the register should use
devres, or none should.
(b) devm_mdiobus_alloc followed by plain mdiobus_register, and then no
mdiobus_unregister at all in the remove path. After the blamed
patch, nobody unregisters the MDIO bus anymore, so this is even more
buggy than the previous case which needs a specific bus
configuration to be seen, this one is an unconditional bug.
In this case, the Realtek drivers fall under category (b). To solve it,
we can register the MDIO bus under devres too, which restores the
previous behavior.
Fixes: ac3a68d566 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Reported-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Reported-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5135e96a3d ]
The Linux device model permits both the ->shutdown and ->remove driver
methods to get called during a shutdown procedure. Example: a DSA switch
which sits on an SPI bus, and the SPI bus driver calls this on its
->shutdown method:
spi_unregister_controller
-> device_for_each_child(&ctlr->dev, NULL, __unregister);
-> spi_unregister_device(to_spi_device(dev));
-> device_del(&spi->dev);
So this is a simple pattern which can theoretically appear on any bus,
although the only other buses on which I've been able to find it are
I2C:
i2c_del_adapter
-> device_for_each_child(&adap->dev, NULL, __unregister_client);
-> i2c_unregister_device(client);
-> device_unregister(&client->dev);
The implication of this pattern is that devices on these buses can be
unregistered after having been shut down. The drivers for these devices
might choose to return early either from ->remove or ->shutdown if the
other callback has already run once, and they might choose that the
->shutdown method should only perform a subset of the teardown done by
->remove (to avoid unnecessary delays when rebooting).
So in other words, the device driver may choose on ->remove to not
do anything (therefore to not unregister an MDIO bus it has registered
on ->probe), because this ->remove is actually triggered by the
device_shutdown path, and its ->shutdown method has already run and done
the minimally required cleanup.
This used to be fine until the blamed commit, but now, the following
BUG_ON triggers:
void mdiobus_free(struct mii_bus *bus)
{
/* For compatibility with error handling in drivers. */
if (bus->state == MDIOBUS_ALLOCATED) {
kfree(bus);
return;
}
BUG_ON(bus->state != MDIOBUS_UNREGISTERED);
bus->state = MDIOBUS_RELEASED;
put_device(&bus->dev);
}
In other words, there is an attempt to free an MDIO bus which was not
unregistered. The attempt to free it comes from the devres release
callbacks of the SPI device, which are executed after the device is
unregistered.
I'm not saying that the fact that MDIO buses allocated using devres
would automatically get unregistered wasn't strange. I'm just saying
that the commit didn't care about auditing existing call paths in the
kernel, and now, the following code sequences are potentially buggy:
(a) devm_mdiobus_alloc followed by plain mdiobus_register, for a device
located on a bus that unregisters its children on shutdown. After
the blamed patch, either both the alloc and the register should use
devres, or none should.
(b) devm_mdiobus_alloc followed by plain mdiobus_register, and then no
mdiobus_unregister at all in the remove path. After the blamed
patch, nobody unregisters the MDIO bus anymore, so this is even more
buggy than the previous case which needs a specific bus
configuration to be seen, this one is an unconditional bug.
In this case, DSA falls into category (a), it tries to be helpful and
registers an MDIO bus on behalf of the switch, which might be on such a
bus. I've no idea why it does it under devres.
It does this on probe:
if (!ds->slave_mii_bus && ds->ops->phy_read)
alloc and register mdio bus
and this on remove:
if (ds->slave_mii_bus && ds->ops->phy_read)
unregister mdio bus
I _could_ imagine using devres because the condition used on remove is
different than the condition used on probe. So strictly speaking, DSA
cannot determine whether the ds->slave_mii_bus it sees on remove is the
ds->slave_mii_bus that _it_ has allocated on probe. Using devres would
have solved that problem. But nonetheless, the existing code already
proceeds to unregister the MDIO bus, even though it might be
unregistering an MDIO bus it has never registered. So I can only guess
that no driver that implements ds->ops->phy_read also allocates and
registers ds->slave_mii_bus itself.
So in that case, if unregistering is fine, freeing must be fine too.
Stop using devres and free the MDIO bus manually. This will make devres
stop attempting to free a still registered MDIO bus on ->shutdown.
Fixes: ac3a68d566 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Reported-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a18cee4791 ]
The abort_work is scheduled when a connection was detected to be
out-of-sync after a link failure. The work calls smc_conn_kill(),
which calls smc_close_active_abort() and that might end up calling
smc_close_cancel_work().
smc_close_cancel_work() cancels any pending close_work and tx_work but
needs to release the sock_lock before and acquires the sock_lock again
afterwards. So when the sock_lock was NOT acquired before then it may
be held after the abort_work completes. Thats why the sock_lock is
acquired before the call to smc_conn_kill() in __smc_lgr_terminate(),
but this is missing in smc_conn_abort_work().
Fix that by acquiring the sock_lock first and release it after the
call to smc_conn_kill().
Fixes: b286a0651e ("net/smc: handle incoming CDC validation message")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63b1279d99 ]
The input parameters may not be reliable. Before using the
queue id, we should check this parameter. Otherwise, memory
overwriting may occur.
Fixes: d341001846 ("net: hns3: refactor the mailbox message between PF and VF")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e184cec5e2 ]
When user change rss 'hfunc' without set rss 'hkey' by ethtool
-X command, the driver will ignore the 'hfunc' for the hkey is
NULL. It's unreasonable. So fix it.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Fixes: 374ad29176 ("net: hns3: Add RSS general configuration support for VF")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5bed8b0704 ]
The smallest TX ring size we support must fit a TX SKB with MAX_SKB_FRAGS
+ 1. Because the first TX BD for a packet is always a long TX BD, we
need an extra TX BD to fit this packet. Define BNXT_MIN_TX_DESC_CNT with
this value to make this more clear. The current code uses a minimum
that is off by 1. Fix it using this constant.
The tx_wake_thresh to determine when to wake up the TX queue is half the
ring size but we must have at least BNXT_MIN_TX_DESC_CNT for the next
packet which may have maximum fragments. So the comparison of the
available TX BDs with tx_wake_thresh should be >= instead of > in the
current code. Otherwise, at the smallest ring size, we will never wake
up the TX queue and will cause TX timeout.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f7afa05c9 ]
The only struct dim_sample member that does not get
initialized by dim_update_sample() is comp_ctr. (There
is special API to initialize comp_ctr:
dim_update_sample_with_comps(), and it is currently used
only for RDMA.) comp_ctr is used to compute curr_stats->cmps
and curr_stats->cpe_ratio (see dim_calc_stats()) which in
turn are consumed by the rdma_dim_*() API. Therefore,
functionally, the net_dim*() API consumers are not affected.
Nevertheless, fix the computation of statistics based
on an uninitialized variable, even if the mentioned statistics
are not used at the moment.
Fixes: ae0e6a5d16 ("enetc: Add adaptive interrupt coalescing")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7237a494de ]
irq_set_affinity_hit() stores a reference to the cpumask_t
parameter in the irq descriptor, and that reference can be
accessed later from irq_affinity_hint_proc_show(). Since
the cpu_mask parameter passed to irq_set_affinity_hit() has
only temporary storage (it's on the stack memory), later
accesses to it are illegal. Thus reads from the corresponding
procfs affinity_hint file can result in paging request oops.
The issue is fixed by the get_cpu_mask() helper, which provides
a permanent storage for the cpumask_t parameter.
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d37e1cab2 ]
When an afs file or directory is modified locally such that the total file
size is extended, i_blocks needs to be recalculated too.
Fix this by making afs_write_end() and afs_edit_dir_add() call
afs_set_i_size() rather than setting inode->i_size directly as that also
recalculates inode->i_blocks.
This can be tested by creating and writing into directories and files and
then examining them with du. Without this change, directories show a 4
blocks (they start out at 2048 bytes) and files show 0 blocks; with this
change, they should show a number of blocks proportional to the file size
rounded up to 1024.
Fixes: 31143d5d51 ("AFS: implement basic file write support")
Fixes: 63a4681ff3 ("afs: Locally edit directory data for mkdir/create/unlink/...")
Reported-by: Markus Suvanto <markus.suvanto@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
Tested-by: Markus Suvanto <markus.suvanto@gmail.com>
cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/r/163113612442.352844.11162345591911691150.stgit@warthog.procyon.org.uk/
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63d49d843e ]
The AFS filesystem is currently triggering the silly-rename cleanup from
afs_d_revalidate() when it sees that a dentry has been changed by a third
party[1]. It should not be doing this as the cleanup includes deleting the
silly-rename target file on iput.
Fix this by removing the places in the d_revalidate handling that validate
anything other than the directory and the dirent. It probably should not
be looking to validate the target inode of the dentry also.
This includes removing the point in afs_d_revalidate() where the inode that
a dentry used to point to was marked as being deleted (AFS_VNODE_DELETED).
We don't know it got deleted. It could have been renamed or it could have
hard links remaining.
This was reproduced by cloning a git repo onto an afs volume on one
machine, switching to another machine and doing "git status", then
switching back to the first and doing "git status". The second status
would show weird output due to ".git/index" getting deleted by the above
mentioned mechanism.
A simpler way to do it is to do:
machine 1: touch a
machine 2: touch b; mv -f b a
machine 1: stat a
on an afs volume. The bug shows up as the stat failing with ENOENT and the
file server log showing that machine 1 deleted "a".
Fixes: 79ddbfa500 ("afs: Implement sillyrename for unlink and rename")
Reported-by: Markus Suvanto <markus.suvanto@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Markus Suvanto <markus.suvanto@gmail.com>
cc: linux-afs@lists.infradead.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=214217#c4 [1]
Link: https://lore.kernel.org/r/163111668100.283156.3851669884664475428.stgit@warthog.procyon.org.uk/
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e8f69b16ee upstream.
If resource allocation and registration fail for a muxed tty device
(e.g. if there are no more minor numbers) the driver should not try to
deregister the never-registered (or already-deregistered) tty.
Fix up the error handling to avoid dereferencing a NULL pointer when
attempting to remove the character device.
Fixes: 72dc1c096c ("HSO: add option hso driver")
Cc: stable@vger.kernel.org # 2.6.27
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab39d3cef5 upstream.
Update the current state as boot state during dpm initialization.
During the subsequent initialization, set_power_state gets called to
transition to the final power state. set_power_state refers to values
from the current state and without current state populated, it could
result in NULL pointer dereference.
For ex: on platforms where PCI speed change is supported through ACPI
ATCS method, the link speed of current state needs to be queried before
deciding on changing to final power state's link speed. The logic to query
ATCS-support was broken on certain platforms. The issue became visible
when broken ATCS-support logic got fixed with commit
f9b7f3703f ("drm/amdgpu/acpi: make ATPX/ATCS structures global (v2)").
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1698
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7215e90981 upstream.
Reporting zones on a SCSI device sometimes fail with the following error:
[76248.516390] ata16.00: invalid transfer count 131328
[76248.523618] sd 15:0:0:0: [sda] REPORT ZONES start lba 536870912 failed
The error (from drivers/ata/libata-scsi.c:ata_scsi_zbc_in_xlat()) indicates
that buffer size is not aligned to SECTOR_SIZE.
This happens when the __vmalloc() failed. Consider we are reporting 4096
zones, then we will have "bufsize = roundup((4096 + 1) * 64,
SECTOR_SIZE)" = (513 * 512) = 262656. Then, __vmalloc() failure halves
the bufsize to 131328, which is no longer aligned to SECTOR_SIZE.
Use rounddown() to ensure the size is always aligned to SECTOR_SIZE and fix
the comment as well.
Link: https://lore.kernel.org/r/20210906140642.2267569-1-naohiro.aota@wdc.com
Fixes: 23a50861ad ("scsi: sd_zbc: Cleanup sd_zbc_alloc_report_buffer()")
Cc: stable@vger.kernel.org # 5.5+
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 74e1eb3b4a upstream.
Driver's tx_empty callback should signal when the transmit shift register
is empty. So when the last character has been sent.
STAT_TX_FIFO_EMP bit signals only that HW transmit FIFO is empty, which
happens when the last byte is loaded into transmit shift register.
STAT_TX_EMP bit signals when the both HW transmit FIFO and transmit shift
register are empty.
So replace STAT_TX_FIFO_EMP check by STAT_TX_EMP in mvebu_uart_tx_empty()
callback function.
Fixes: 30530791a7 ("serial: mvebu-uart: initial support for Armada-3700 serial port")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20210911132017.25505-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58877b0824 upstream.
It has been observed with certain PCIe USB cards (like Inateck connected
to AM64 EVM or J7200 EVM) that as soon as the primary roothub is
registered, port status change is handled even before xHC is running
leading to cold plug USB devices not detected. For such cases, registering
both the root hubs along with the second HCD is required. Add support for
deferring roothub registration in usb_add_hcd(), so that both primary and
secondary roothubs are registered along with the second HCD.
CC: stable@vger.kernel.org # 5.4+
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210909064200.16216-2-kishon@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8cfac9a674 upstream.
After we start to do core soft reset while usb role switch,
the phy init is invoked at every switch to device mode, but
its counter part de-init is missing, this causes the actual
phy init can not be done when we really want to re-init phy
like system resume, because the counter maintained by phy
core is not 0. considering phy init is actually redundant for
role switch, so move out the phy init from core soft reset to
dwc3 core init where is the only place required.
Fixes: f88359e158 ("usb: dwc3: core: Do core softreset when switch mode")
Cc: <stable@vger.kernel.org>
Tested-by: faqiang.zhu <faqiang.zhu@nxp.com>
Tested-by: John Stultz <john.stultz@linaro.org> #HiKey960
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/1631068099-13559-1-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5fdb55c1ac upstream.
During BC_FREE_BUFFER processing, the BINDER_TYPE_FDA object
cleanup may close 1 or more fds. The close operations are
completed using the task work mechanism -- which means the thread
needs to return to userspace or the file object may never be
dereferenced -- which can lead to hung processes.
Force the binder thread back to userspace if an fd is closed during
BC_FREE_BUFFER handling.
Fixes: 80cd795630 ("binder: fix use-after-free due to ksys_close() during fdget()")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Martijn Coenen <maco@android.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Todd Kjos <tkjos@google.com>
Link: https://lore.kernel.org/r/20210830195146.587206-1-tkjos@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d91adc5322 upstream.
This reverts commit f3de5d857b.
That commit broke USB on all routers that have USB always powered on and
don't require toggling any GPIO. It's a majority of devices actually.
The original code worked and seemed safe: vcc GPIO is optional and
bcma_hci_platform_power_gpio() takes care of checking the pointer before
using it.
This revert fixes:
[ 10.801127] bcma_hcd: probe of bcma0:11 failed with error -2
Fixes: f3de5d857b ("USB: bcma: Add a check for devm_gpiod_get")
Cc: stable <stable@vger.kernel.org>
Cc: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20210831065419.18371-1-zajec5@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b55d37ef6b upstream.
ScanLogic SL11R-IDE with firmware older than 2.6c (the latest one) has
broken tag handling, preventing the device from working at all:
usb 1-1: new full-speed USB device number 2 using uhci_hcd
usb 1-1: New USB device found, idVendor=04ce, idProduct=0002, bcdDevice= 2.60
usb 1-1: New USB device strings: Mfr=1, Product=1, SerialNumber=0
usb 1-1: Product: USB Device
usb 1-1: Manufacturer: USB Device
usb-storage 1-1:1.0: USB Mass Storage device detected
scsi host2: usb-storage 1-1:1.0
usbcore: registered new interface driver usb-storage
usb 1-1: reset full-speed USB device number 2 using uhci_hcd
usb 1-1: reset full-speed USB device number 2 using uhci_hcd
usb 1-1: reset full-speed USB device number 2 using uhci_hcd
usb 1-1: reset full-speed USB device number 2 using uhci_hcd
Add US_FL_BULK_IGNORE_TAG to fix it. Also update my e-mail address.
2.6c is the only firmware that claims Linux compatibility.
The firmware can be upgraded using ezotgdbg utility:
https://github.com/asciilifeform/ezotgdbg
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ondrej Zary <linux@zary.sk>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210913210106.12717-1-linux@zary.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0594c58161 upstream.
The initial observation was that in PV mode under Xen 32-bit user space
didn't work anymore. Attempts of system calls ended in #GP(0x402). All
of the sudden the vector 0x80 handler was not in place anymore. As it
turns out up to 5.13 redundant initialization did occur: Once from
cpu_initialize_context() (through its VCPUOP_initialise hypercall) and a
2nd time while each CPU was brought fully up. This 2nd initialization is
now gone, uncovering that the 1st one was flawed: Unlike for the
set_trap_table hypercall, a full virtual IDT needs to be specified here;
the "vector" fields of the individual entries are of no interest. With
many (kernel) IDT entries still(?) (i.e. at that point at least) empty,
the syscall vector 0x80 ended up in slot 0x20 of the virtual IDT, thus
becoming the domain's handler for vector 0x20.
Make xen_convert_trap_info() fit for either purpose, leveraging the fact
that on the xen_copy_trap_info() path the table starts out zero-filled.
This includes moving out the writing of the sentinel, which would also
have lead to a buffer overrun in the xen_copy_trap_info() case if all
(kernel) IDT entries were populated. Convert the writing of the sentinel
to clearing of the entire table entry rather than just the address
field.
(I didn't bother trying to identify the commit which uncovered the issue
in 5.14; the commit named below is the one which actually introduced the
bad code.)
Fixes: f87e4cac4f ("xen: SMP guest support")
Cc: stable@vger.kernel.org
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/7a266932-092e-b68f-f2bb-1473b61adc6e@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ed38fd4a1 upstream.
Although very unlikely that the tlink pointer would be null in this case,
get_next_mid function can in theory return null (but not an error)
so need to check for null (not for IS_ERR, which can not be returned
here).
Address warning:
fs/smbfs_client/connect.c:2392 cifs_match_super()
warn: 'tlink' isn't an ERR_PTR
Pointed out by Dan Carpenter via smatch code analysis tool
CC: stable@vger.kernel.org
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 91bb163e1e upstream.
According USB spec each ISOC transaction should be performed in a
designated for that transaction interval. On bus errors or delays
in operating system scheduling of client software can result in no
packet being transferred for a (micro)frame. An error indication
should be returned as status to the client software in such a case.
Current implementation in case of missed/dropped interval send same
data in next possible interval instead of reporting missed isoc.
This fix complete requests with -ENODATA if interval elapsed.
HSOTG core in BDMA and Slave modes haven't HW support for
(micro)frames tracking, this is why SW should care about tracking
of (micro)frames. Because of that method and consider operating
system scheduling delays, added few additional checking's of elapsed
target (micro)frame:
1. Immediately before enabling EP to start transfer.
2. With any transfer completion interrupt.
3. With incomplete isoc in/out interrupt.
4. With EP disabled interrupt because of incomplete transfer.
5. With OUT token received while EP disabled interrupt (for OUT
transfers).
6. With NAK replied to IN token interrupt (for IN transfers).
As part of ISOC flow, additionally fixed 'current' and 'target' frame
calculation functions. In HS mode SOF limits provided by DSTS register
is 0x3fff, but in non HS mode this limit is 0x7ff.
Tested by internal tool which also using for dwc3 testing.
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/95d1423adf4b0f68187c9894820c4b7e964a3f7f.1631175721.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bcbda81020 upstream.
We get an unexpected value of /proc/sys/vm/overcommit_memory after
running the following program:
int main()
{
int fd = open("/proc/sys/vm/overcommit_memory", O_RDWR);
write(fd, "1", 1);
write(fd, "2", 1);
close(fd);
}
write(fd, "2", 1) will pass *ppos = 1 to proc_dointvec_minmax.
proc_dointvec_minmax will return 0 without setting new_policy.
t.data = &new_policy;
ret = proc_dointvec_minmax(&t, write, buffer, lenp, ppos)
-->do_proc_dointvec
-->__do_proc_dointvec
if (write) {
if (proc_first_pos_non_zero_ignore(ppos, table))
goto out;
sysctl_overcommit_memory = new_policy;
so sysctl_overcommit_memory will be set to an uninitialized value.
Check whether new_policy has been changed by proc_dointvec_minmax.
Link: https://lkml.kernel.org/r/20210923020524.13289-1-chenjun102@huawei.com
Fixes: 56f3547bfa ("mm: adjust vm_committed_as_batch according to vm overcommit policy")
Signed-off-by: Chen Jun <chenjun102@huawei.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Feng Tang <feng.tang@intel.com>
Reviewed-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Rui Xiang <rui.xiang@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b58db229eb617d97d5746113b77045f1f884bcb upstream.
Measurements in different conditions showed that aardvark hardware PIO
response can take up to 1.44s. Increase wait timeout from 1ms to 1.5s to
ensure that we do not miss responses from hardware. After 1.44s hardware
returns errors (e.g. Completer abort).
The previous two patches fixed checking for PIO status, so now we can use
it to also catch errors which are reported by hardware after 1.44s.
After applying this patch, kernel can detect and print PIO errors to dmesg:
[ 6.879999] advk-pcie d0070000.pcie: Non-posted PIO Response Status: CA, 0xe00 @ 0x100004
[ 6.896436] advk-pcie d0070000.pcie: Posted PIO Response Status: COMP_ERR, 0x804 @ 0x100004
[ 6.913049] advk-pcie d0070000.pcie: Posted PIO Response Status: COMP_ERR, 0x804 @ 0x100010
[ 6.929663] advk-pcie d0070000.pcie: Non-posted PIO Response Status: CA, 0xe00 @ 0x100010
[ 6.953558] advk-pcie d0070000.pcie: Posted PIO Response Status: COMP_ERR, 0x804 @ 0x100014
[ 6.970170] advk-pcie d0070000.pcie: Non-posted PIO Response Status: CA, 0xe00 @ 0x100014
[ 6.994328] advk-pcie d0070000.pcie: Posted PIO Response Status: COMP_ERR, 0x804 @ 0x100004
Without this patch kernel prints only a generic error to dmesg:
[ 5.246847] advk-pcie d0070000.pcie: config read/write timed out
Link: https://lore.kernel.org/r/20210722144041.12661-3-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org # 7fbcb5da81 ("PCI: aardvark: Don't rely on jiffies while holding spinlock")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e8f71f8923 upstream.
nvkm test builds fail with the following error.
drivers/gpu/drm/nouveau/nvkm/engine/device/ctrl.c: In function 'nvkm_control_mthd_pstate_info':
drivers/gpu/drm/nouveau/nvkm/engine/device/ctrl.c:60:35: error: overflow in conversion from 'int' to '__s8' {aka 'signed char'} changes value from '-251' to '5'
The code builds on most architectures, but fails on parisc where ENOSYS
is defined as 251.
Replace the error code with -ENODEV (-19). The actual error code does
not really matter and is not passed to userspace - it just has to be
negative.
Fixes: 7238eca4cf ("drm/nouveau: expose pstate selection per-power source in sysfs")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9848417926 ]
The intel powerclamp driver will setup a per-CPU worker with RT
priority. The worker will then invoke play_idle() in which it remains in
the idle poll loop until it is stopped by the timer it started earlier.
That timer needs to expire in hard interrupt context on PREEMPT_RT.
Otherwise the timer will expire in ksoftirqd as a SOFT timer but that task
won't be scheduled on the CPU because its priority is lower than the
priority of the worker which is in the idle loop.
Always expire the idle timer in hard interrupt context.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210906113034.jgfxrjdvxnjqgtmc@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 884f0e84f1 ]
The pending timer has been set up in blk_throtl_init(). However, the
timer is not deleted in blk_throtl_exit(). This means that the timer
handler may still be running after freeing the timer, which would
result in a use-after-free.
Fix by calling del_timer_sync() to delete the timer in blk_throtl_exit().
Signed-off-by: Li Jinlin <lijinlin3@huawei.com>
Link: https://lore.kernel.org/r/20210907121242.2885564-1-lijinlin3@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d44084c934 ]
A consumer is expected to disable a PWM before calling pwm_put(). And if
they didn't there is hopefully a good reason (or the consumer needs
fixing). Also if disabling an enabled PWM was the right thing to do,
this should better be done in the framework instead of in each low level
driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d768cd7fd ]
A consumer is expected to disable a PWM before calling pwm_put(). And if
they didn't there is hopefully a good reason (or the consumer needs
fixing). Also if disabling an enabled PWM was the right thing to do,
this should better be done in the framework instead of in each low level
driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c68eb29c8e ]
A consumer is expected to disable a PWM before calling pwm_put(). And if
they didn't there is hopefully a good reason (or the consumer needs
fixing). Also if disabling an enabled PWM was the right thing to do,
this should better be done in the framework instead of in each low level
driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6c849012b ]
Currently there is no validity check for event ID received from F/W,
Thus exposing driver to memory overrun.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f5dec07ac ]
Patch series "nilfs2: fix incorrect usage of kobject".
This patchset from Nanyong Sun fixes memory leak issues and a NULL
pointer dereference issue caused by incorrect usage of kboject in nilfs2
sysfs implementation.
This patch (of 6):
Reported by syzkaller:
BUG: memory leak
unreferenced object 0xffff888100ca8988 (size 8):
comm "syz-executor.1", pid 1930, jiffies 4294745569 (age 18.052s)
hex dump (first 8 bytes):
6c 6f 6f 70 31 00 ff ff loop1...
backtrace:
kstrdup+0x36/0x70 mm/util.c:60
kstrdup_const+0x35/0x60 mm/util.c:83
kvasprintf_const+0xf1/0x180 lib/kasprintf.c:48
kobject_set_name_vargs+0x56/0x150 lib/kobject.c:289
kobject_add_varg lib/kobject.c:384 [inline]
kobject_init_and_add+0xc9/0x150 lib/kobject.c:473
nilfs_sysfs_create_device_group+0x150/0x7d0 fs/nilfs2/sysfs.c:986
init_nilfs+0xa21/0xea0 fs/nilfs2/the_nilfs.c:637
nilfs_fill_super fs/nilfs2/super.c:1046 [inline]
nilfs_mount+0x7b4/0xe80 fs/nilfs2/super.c:1316
legacy_get_tree+0x105/0x210 fs/fs_context.c:592
vfs_get_tree+0x8e/0x2d0 fs/super.c:1498
do_new_mount fs/namespace.c:2905 [inline]
path_mount+0xf9b/0x1990 fs/namespace.c:3235
do_mount+0xea/0x100 fs/namespace.c:3248
__do_sys_mount fs/namespace.c:3456 [inline]
__se_sys_mount fs/namespace.c:3433 [inline]
__x64_sys_mount+0x14b/0x1f0 fs/namespace.c:3433
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3b/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
If kobject_init_and_add return with error, then the cleanup of kobject
is needed because memory may be allocated in kobject_init_and_add
without freeing.
And the place of cleanup_dev_kobject should use kobject_put to free the
memory associated with the kobject. As the section "Kobject removal" of
"Documentation/core-api/kobject.rst" says, kobject_del() just makes the
kobject "invisible", but it is not cleaned up. And no more cleanup will
do after cleanup_dev_kobject, so kobject_put is needed here.
Link: https://lkml.kernel.org/r/1625651306-10829-1-git-send-email-konishi.ryusuke@gmail.com
Link: https://lkml.kernel.org/r/1625651306-10829-2-git-send-email-konishi.ryusuke@gmail.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Link: https://lkml.kernel.org/r/20210629022556.3985106-2-sunnanyong@huawei.com
Signed-off-by: Nanyong Sun <sunnanyong@huawei.com>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f96a5bfa1 ]
We update the ctime/mtime of a block device when we remove it so that
blkid knows the device changed. However we do this by re-opening the
block device and calling filp_update_time. This is more correct because
it'll call the inode->i_op->update_time if it exists, but the block dev
inodes do not do this. Instead call generic_update_time() on the
bd_inode in order to avoid the blkdev_open path and get rid of the
following lockdep splat:
======================================================
WARNING: possible circular locking dependency detected
5.14.0-rc2+ #406 Not tainted
------------------------------------------------------
losetup/11596 is trying to acquire lock:
ffff939640d2f538 ((wq_completion)loop0){+.+.}-{0:0}, at: flush_workqueue+0x67/0x5e0
but task is already holding lock:
ffff939655510c68 (&lo->lo_mutex){+.+.}-{3:3}, at: __loop_clr_fd+0x41/0x660 [loop]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #4 (&lo->lo_mutex){+.+.}-{3:3}:
__mutex_lock+0x7d/0x750
lo_open+0x28/0x60 [loop]
blkdev_get_whole+0x25/0xf0
blkdev_get_by_dev.part.0+0x168/0x3c0
blkdev_open+0xd2/0xe0
do_dentry_open+0x161/0x390
path_openat+0x3cc/0xa20
do_filp_open+0x96/0x120
do_sys_openat2+0x7b/0x130
__x64_sys_openat+0x46/0x70
do_syscall_64+0x38/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
-> #3 (&disk->open_mutex){+.+.}-{3:3}:
__mutex_lock+0x7d/0x750
blkdev_get_by_dev.part.0+0x56/0x3c0
blkdev_open+0xd2/0xe0
do_dentry_open+0x161/0x390
path_openat+0x3cc/0xa20
do_filp_open+0x96/0x120
file_open_name+0xc7/0x170
filp_open+0x2c/0x50
btrfs_scratch_superblocks.part.0+0x10f/0x170
btrfs_rm_device.cold+0xe8/0xed
btrfs_ioctl+0x2a31/0x2e70
__x64_sys_ioctl+0x80/0xb0
do_syscall_64+0x38/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
-> #2 (sb_writers#12){.+.+}-{0:0}:
lo_write_bvec+0xc2/0x240 [loop]
loop_process_work+0x238/0xd00 [loop]
process_one_work+0x26b/0x560
worker_thread+0x55/0x3c0
kthread+0x140/0x160
ret_from_fork+0x1f/0x30
-> #1 ((work_completion)(&lo->rootcg_work)){+.+.}-{0:0}:
process_one_work+0x245/0x560
worker_thread+0x55/0x3c0
kthread+0x140/0x160
ret_from_fork+0x1f/0x30
-> #0 ((wq_completion)loop0){+.+.}-{0:0}:
__lock_acquire+0x10ea/0x1d90
lock_acquire+0xb5/0x2b0
flush_workqueue+0x91/0x5e0
drain_workqueue+0xa0/0x110
destroy_workqueue+0x36/0x250
__loop_clr_fd+0x9a/0x660 [loop]
block_ioctl+0x3f/0x50
__x64_sys_ioctl+0x80/0xb0
do_syscall_64+0x38/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
other info that might help us debug this:
Chain exists of:
(wq_completion)loop0 --> &disk->open_mutex --> &lo->lo_mutex
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&lo->lo_mutex);
lock(&disk->open_mutex);
lock(&lo->lo_mutex);
lock((wq_completion)loop0);
*** DEADLOCK ***
1 lock held by losetup/11596:
#0: ffff939655510c68 (&lo->lo_mutex){+.+.}-{3:3}, at: __loop_clr_fd+0x41/0x660 [loop]
stack backtrace:
CPU: 1 PID: 11596 Comm: losetup Not tainted 5.14.0-rc2+ #406
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.13.0-2.fc32 04/01/2014
Call Trace:
dump_stack_lvl+0x57/0x72
check_noncircular+0xcf/0xf0
? stack_trace_save+0x3b/0x50
__lock_acquire+0x10ea/0x1d90
lock_acquire+0xb5/0x2b0
? flush_workqueue+0x67/0x5e0
? lockdep_init_map_type+0x47/0x220
flush_workqueue+0x91/0x5e0
? flush_workqueue+0x67/0x5e0
? verify_cpu+0xf0/0x100
drain_workqueue+0xa0/0x110
destroy_workqueue+0x36/0x250
__loop_clr_fd+0x9a/0x660 [loop]
? blkdev_ioctl+0x8d/0x2a0
block_ioctl+0x3f/0x50
__x64_sys_ioctl+0x80/0xb0
do_syscall_64+0x38/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6d37ccdd2 ]
capsnaps will take inode references via ihold when queueing to flush.
When force unmounting, the client will just close the sessions and
may never get a flush reply, causing a leak and inode ref leak.
Fix this by removing the capsnaps for an inode when removing the caps.
URL: https://tracker.ceph.com/issues/52295
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b11ed50346 ]
The current code will update the mtime and then try to get caps to
handle the write. If we end up having to request caps from the MDS, then
the mtime in the cap grant will clobber the updated mtime and it'll be
lost.
This is most noticable when two clients are alternately writing to the
same file. Fw caps are continually being granted and revoked, and the
mtime ends up stuck because the updated mtimes are always being
overwritten with the old one.
Fix this by changing the order of operations in ceph_write_iter to get
the caps before updating the times. Also, make sure we check the pool
full conditions before even getting any caps or uninlining.
URL: https://tracker.ceph.com/issues/46574
Reported-by: Jozef Kováč <kovac@firma.zoznam.sk>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Luis Henriques <lhenriques@suse.de>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aac6c0f907 ]
The xilinx dma driver uses the consistent allocations, so for correct
operation also set the DMA mask for coherent APIs. It fixes the below
kernel crash with dmatest client when DMA IP is configured with 64-bit
address width and linux is booted from high (>4GB) memory.
Call trace:
[ 489.531257] dma_alloc_from_pool+0x8c/0x1c0
[ 489.535431] dma_direct_alloc+0x284/0x330
[ 489.539432] dma_alloc_attrs+0x80/0xf0
[ 489.543174] dma_pool_alloc+0x160/0x2c0
[ 489.547003] xilinx_cdma_prep_memcpy+0xa4/0x180
[ 489.551524] dmatest_func+0x3cc/0x114c
[ 489.555266] kthread+0x124/0x130
[ 489.558486] ret_from_fork+0x10/0x3c
[ 489.562051] ---[ end trace 248625b2d596a90a ]---
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Reviewed-by: Harini Katakam <harini.katakam@xilinx.com>
Link: https://lore.kernel.org/r/1629363528-30347-1-git-send-email-radhey.shyam.pandey@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3811a50ad ]
Currently, iommu_init_ga() checks and disables IOMMU VAPIC support
(i.e. AMD AVIC support in IOMMU) when GAMSup feature bit is not set.
However it forgets to clear IRQ_POSTING_CAP from the previously set
amd_iommu_irq_ops.capability.
This triggers an invalid page fault bug during guest VM warm reboot
if AVIC is enabled since the irq_remapping_cap(IRQ_POSTING_CAP) is
incorrectly set, and crash the system with the following kernel trace.
BUG: unable to handle page fault for address: 0000000000400dd8
RIP: 0010:amd_iommu_deactivate_guest_mode+0x19/0xbc
Call Trace:
svm_set_pi_irte_mode+0x8a/0xc0 [kvm_amd]
? kvm_make_all_cpus_request_except+0x50/0x70 [kvm]
kvm_request_apicv_update+0x10c/0x150 [kvm]
svm_toggle_avic_for_irq_window+0x52/0x90 [kvm_amd]
svm_enable_irq_window+0x26/0xa0 [kvm_amd]
vcpu_enter_guest+0xbbe/0x1560 [kvm]
? avic_vcpu_load+0xd5/0x120 [kvm_amd]
? kvm_arch_vcpu_load+0x76/0x240 [kvm]
? svm_get_segment_base+0xa/0x10 [kvm_amd]
kvm_arch_vcpu_ioctl_run+0x103/0x590 [kvm]
kvm_vcpu_ioctl+0x22a/0x5d0 [kvm]
__x64_sys_ioctl+0x84/0xc0
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xae
Fixes by moving the initializing of AMD IOMMU interrupt remapping mode
(amd_iommu_guest_ir) earlier before setting up the
amd_iommu_irq_ops.capability with appropriate IRQ_POSTING_CAP flag.
[joro: Squashed the two patches and limited
check_features_on_all_iommus() to CONFIG_IRQ_REMAP
to fix a compile warning.]
Signed-off-by: Wei Huang <wei.huang2@amd.com>
Co-developed-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Link: https://lore.kernel.org/r/20210820202957.187572-2-suravee.suthikulpanit@amd.com
Link: https://lore.kernel.org/r/20210820202957.187572-3-suravee.suthikulpanit@amd.com
Fixes: 8bda0cfbdc ("iommu/amd: Detect and initialize guest vAPIC log")
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 907872baa9 ]
parisc build test images fail to compile with the following error.
drivers/parisc/dino.c:160:12: error:
'pci_dev_is_behind_card_dino' defined but not used
Move the function just ahead of its only caller to avoid the error.
Fixes: 5fa1659105 ("parisc: Disable HP HSC-PCI Cards to prevent kernel crash")
Cc: Helge Deller <deller@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b92d4add5 ]
DEFINE_SMP_CALL_CACHE_FUNCTION() was usefel before the CPU hotplug rework
to ensure that the cache related functions are called on the upcoming CPU
because the notifier itself could run on any online CPU.
The hotplug state machine guarantees that the callbacks are invoked on the
upcoming CPU. So there is no need to have this SMP function call
obfuscation. That indirection was missed when the hotplug notifiers were
converted.
This also solves the problem of ARM64 init_cache_level() invoking ACPI
functions which take a semaphore in that context. That's invalid as SMP
function calls run with interrupts disabled. Running it just from the
callback in context of the CPU hotplug thread solves this.
Fixes: 8571890e15 ("arm64: Add support for ACPI based firmware tables")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Will Deacon <will@kernel.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/871r69ersb.ffs@tglx
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3dc549986 ]
Due to high latency in PCIE clock switching on RKL platforms,
switching the PCIE clock dynamically at runtime can lead to HDMI/DP
audio problems. On newer asics this is handled in the SMU firmware.
For SMU7-based asics, disable PCIE clock switching to avoid the issue.
AMD provide a parameter to disable PICE_DPM.
modprobe amdgpu ppfeaturemask=0xfff7bffb
It's better to contorl PCIE_DPM in amd gpu driver,
switch PCI_DPM by determining intel RKL platform for SMU7-based asics.
Fixes: 1a31474cdb ("drm/amd/pm: workaround for audio noise issue")
Ref: https://lists.freedesktop.org/archives/amd-gfx/2021-August/067413.html
Signed-off-by: Koba Ko <koba.ko@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb83610762 ]
There are two pairs of declarations for thermal_cooling_device_register()
and thermal_of_cooling_device_register(), and only one set was changed
in a recent patch, so the other one now causes a compile-time warning:
drivers/net/wireless/mediatek/mt76/mt7915/init.c: In function 'mt7915_thermal_init':
drivers/net/wireless/mediatek/mt76/mt7915/init.c:134:48: error: passing argument 1 of 'thermal_cooling_device_register' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
134 | cdev = thermal_cooling_device_register(wiphy_name(wiphy), phy,
| ^~~~~~~~~~~~~~~~~
In file included from drivers/net/wireless/mediatek/mt76/mt7915/init.c:7:
include/linux/thermal.h:407:39: note: expected 'char *' but argument is of type 'const char *'
407 | thermal_cooling_device_register(char *type, void *devdata,
| ~~~~~~^~~~
Change the dummy helper functions to have the same arguments as the
normal version.
Fixes: f991de53a8 ("thermal: make device_register's type argument const")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210722090717.1116748-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4002173b7 ]
The first thing metric_delayed_work does is check mdsc->stopping,
and then return immediately if it's set. That's good since we would
have already torn down the metric structures at this point, otherwise,
but there is no locking around mdsc->stopping.
It's possible that the ceph_metric_destroy call could race with the
delayed_work, in which case we could end up with the delayed_work
accessing destroyed percpu variables.
At this point in the mdsc teardown, the "stopping" flag has already been
set, so there's no benefit to flushing the work. Move the work
cancellation in ceph_metric_destroy ahead of the percpu variable
destruction, and eliminate the flush_delayed_work call in
ceph_mdsc_destroy.
Fixes: 18f473b384 ("ceph: periodically send perf metrics to MDSes")
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Xiubo Li <xiubli@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d453ceb654 ]
Add trace event to report samples and their timestamp coming from the
EC. It allows to check if the timestamps are correct and the filter is
working correctly without introducing too much latency.
To enable these events:
cd /sys/kernel/debug/tracing/
echo 1 > events/cros_ec/enable
echo 0 > events/cros_ec/cros_ec_request_start/enable
echo 0 > events/cros_ec/cros_ec_request_done/enable
echo 1 > tracing_on
cat trace_pipe
Observe event flowing:
irq/105-chromeo-95 [000] .... 613.659758: cros_ec_sensorhub_timestamp: ...
irq/105-chromeo-95 [000] .... 613.665219: cros_ec_sensorhub_filter: dx: ...
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 020162d6f4 upstream.
This fixes a race condition: After pwmchip_add() is called there might
already be a consumer and then modifying the hardware behind the
consumer's back is bad. So reset before calling pwmchip_add().
Note that reseting the hardware isn't the right thing to do if the PWM
is already running as it might e.g. disable (or even enable) a backlight
that is supposed to be on (or off).
Fixes: 4dce82c1e8 ("pwm: add pwm-mxs support")
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d2813fb17 upstream.
This fixes a race condition: After pwmchip_add() is called there might
already be a consumer and then modifying the hardware behind the
consumer's back is bad. So set the default before.
(Side-note: I don't know what this register setting actually does, if
this modifies the polarity there is an inconsistency because the
inversed polarity isn't considered if the PWM is already running during
.probe().)
Fixes: acfd92fdfb ("pwm: lpc32xx: Set PWM_PIN_LEVEL bit to default value")
Cc: Sylvain Lemieux <slemieux@tycoint.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a9344cd0a upstream.
There are variables(power.may_skip_resume and dev->power.must_resume)
and DPM_FLAG_MAY_SKIP_RESUME flags to control the resume of devices after
a system wide suspend transition.
Setting the DPM_FLAG_MAY_SKIP_RESUME flag means that the driver allows
its "noirq" and "early" resume callbacks to be skipped if the device
can be left in suspend after a system-wide transition into the working
state. PM core determines that the driver's "noirq" and "early" resume
callbacks should be skipped or not with dev_pm_skip_resume() function by
checking power.may_skip_resume variable.
power.must_resume variable is getting set to false in __device_suspend()
function without checking device's DPM_FLAG_MAY_SKIP_RESUME settings.
In problematic scenario, where all the devices in the suspend_late
stage are successful and some device can fail to suspend in
suspend_noirq phase. So some devices successfully suspended in suspend_late
stage are not getting chance to execute __device_suspend_noirq()
to set dev->power.must_resume variable to true and not getting
resumed in early_resume phase.
Add a check for device's DPM_FLAG_MAY_SKIP_RESUME flag before
setting power.must_resume variable in __device_suspend function.
Fixes: 6e176bf8d4 ("PM: sleep: core: Do not skip callbacks in the resume phase")
Signed-off-by: Prasad Sodagudi <psodagud@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98e2e409e7 upstream.
When the refcount is decreased to 0, the resource reclamation branch is
entered. Before CPU0 reaches the race point (1), CPU1 may obtain the
spinlock and traverse the rbtree to find 'root', see
nilfs_lookup_root().
Although CPU1 will call refcount_inc() to increase the refcount, it is
obviously too late. CPU0 will release 'root' directly, CPU1 then
accesses 'root' and triggers UAF.
Use refcount_dec_and_lock() to ensure that both the operations of
decrease refcount to 0 and link deletion are lock protected eliminates
this risk.
CPU0 CPU1
nilfs_put_root():
<-------- (1)
spin_lock(&nilfs->ns_cptree_lock);
rb_erase(&root->rb_node, &nilfs->ns_cptree);
spin_unlock(&nilfs->ns_cptree_lock);
kfree(root);
<-------- use-after-free
refcount_t: underflow; use-after-free.
WARNING: CPU: 2 PID: 9476 at lib/refcount.c:28 \
refcount_warn_saturate+0x1cf/0x210 lib/refcount.c:28
Modules linked in:
CPU: 2 PID: 9476 Comm: syz-executor.0 Not tainted 5.10.45-rc1+ #3
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), ...
RIP: 0010:refcount_warn_saturate+0x1cf/0x210 lib/refcount.c:28
... ...
Call Trace:
__refcount_sub_and_test include/linux/refcount.h:283 [inline]
__refcount_dec_and_test include/linux/refcount.h:315 [inline]
refcount_dec_and_test include/linux/refcount.h:333 [inline]
nilfs_put_root+0xc1/0xd0 fs/nilfs2/the_nilfs.c:795
nilfs_segctor_destroy fs/nilfs2/segment.c:2749 [inline]
nilfs_detach_log_writer+0x3fa/0x570 fs/nilfs2/segment.c:2812
nilfs_put_super+0x2f/0xf0 fs/nilfs2/super.c:467
generic_shutdown_super+0xcd/0x1f0 fs/super.c:464
kill_block_super+0x4a/0x90 fs/super.c:1446
deactivate_locked_super+0x6a/0xb0 fs/super.c:335
deactivate_super+0x85/0x90 fs/super.c:366
cleanup_mnt+0x277/0x2e0 fs/namespace.c:1118
__cleanup_mnt+0x15/0x20 fs/namespace.c:1125
task_work_run+0x8e/0x110 kernel/task_work.c:151
tracehook_notify_resume include/linux/tracehook.h:188 [inline]
exit_to_user_mode_loop kernel/entry/common.c:164 [inline]
exit_to_user_mode_prepare+0x13c/0x170 kernel/entry/common.c:191
syscall_exit_to_user_mode+0x16/0x30 kernel/entry/common.c:266
do_syscall_64+0x45/0x80 arch/x86/entry/common.c:56
entry_SYSCALL_64_after_hwframe+0x44/0xa9
There is no reproduction program, and the above is only theoretical
analysis.
Link: https://lkml.kernel.org/r/1629859428-5906-1-git-send-email-konishi.ryusuke@gmail.com
Fixes: ba65ae4729 ("nilfs2: add checkpoint tree to nilfs object")
Link: https://lkml.kernel.org/r/20210723012317.4146-1-thunder.leizhen@huawei.com
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e1fbbd0731 upstream.
Keno Fischer reported that when a binray loaded via ld-linux-x the
prctl(PR_SET_MM_MAP) doesn't allow to setup brk value because it lays
before mm:end_data.
For example a test program shows
| # ~/t
|
| start_code 401000
| end_code 401a15
| start_stack 7ffce4577dd0
| start_data 403e10
| end_data 40408c
| start_brk b5b000
| sbrk(0) b5b000
and when executed via ld-linux
| # /lib64/ld-linux-x86-64.so.2 ~/t
|
| start_code 7fc25b0a4000
| end_code 7fc25b0c4524
| start_stack 7fffcc6b2400
| start_data 7fc25b0ce4c0
| end_data 7fc25b0cff98
| start_brk 55555710c000
| sbrk(0) 55555710c000
This of course prevent criu from restoring such programs. Looking into
how kernel operates with brk/start_brk inside brk() syscall I don't see
any problem if we allow to setup brk/start_brk without checking for
end_data. Even if someone pass some weird address here on a purpose then
the worst possible result will be an unexpected unmapping of existing vma
(own vma, since prctl works with the callers memory) but test for
RLIMIT_DATA is still valid and a user won't be able to gain more memory in
case of expanding VMAs via new values shipped with prctl call.
Link: https://lkml.kernel.org/r/20210121221207.GB2174@grain
Fixes: bbdc6076d2 ("binfmt_elf: move brk out of mmap when doing direct loader exec")
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Reported-by: Keno Fischer <keno@juliacomputing.com>
Acked-by: Andrey Vagin <avagin@gmail.com>
Tested-by: Andrey Vagin <avagin@gmail.com>
Cc: Dmitry Safonov <0x7f454c46@gmail.com>
Cc: Kirill Tkhai <ktkhai@virtuozzo.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Cc: Alexander Mikhalitsyn <alexander.mikhalitsyn@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a86d41404 upstream.
Currently perf saves a build-id with size but old versions assumes the
size of 20. In case the build-id is less than 20 (like for MD5), it'd
fill the rest with 0s.
I saw a problem when old version of perf record saved a binary in the
build-id cache and new version of perf reads the data. The symbols
should be read from the build-id cache (as the path no longer has the
same binary) but it failed due to mismatch in the build-id.
symsrc__init: build id mismatch for /home/namhyung/.debug/.build-id/53/e4c2f42a4c61a2d632d92a72afa08f00000000/elf.
The build-id event in the data has 20 byte build-ids, but it saw a
different size (16) when it reads the build-id of the elf file in the
build-id cache.
$ readelf -n ~/.debug/.build-id/53/e4c2f42a4c61a2d632d92a72afa08f00000000/elf
Displaying notes found in: .note.gnu.build-id
Owner Data size Description
GNU 0x00000010 NT_GNU_BUILD_ID (unique build ID bitstring)
Build ID: 53e4c2f42a4c61a2d632d92a72afa08f
Let's fix this by allowing trailing zeros if the size is different.
Fixes: 39be8d0115 ("perf tools: Pass build_id object to dso__build_id_equal()")
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20210910224630.1084877-1-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 099ec97ac9 upstream.
clang warns:
drivers/staging/rtl8192u/r8192U_core.c:4268:20: warning: bitwise and of
boolean expressions; did you mean logical and? [-Wbool-operation-and]
bpacket_toself = bpacket_match_bssid &
^~~~~~~~~~~~~~~~~~~~~
&&
1 warning generated.
Replace the bitwise AND with a logical one to clear up the warning, as
that is clearly what was intended.
Fixes: 8fc8598e61 ("Staging: Added Realtek rtl8192u driver to staging")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20210814235625.1780033-1-nathan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef6c8d6ccf upstream.
When SCTP handles an INIT chunk, it calls for example:
sctp_sf_do_5_1B_init
sctp_verify_init
sctp_verify_param
sctp_process_init
sctp_process_param
handling of SCTP_PARAM_SET_PRIMARY
sctp_verify_init() wasn't doing proper size validation and neither the
later handling, allowing it to work over the chunk itself, possibly being
uninitialized memory.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6ffe7671b upstream.
In one of the fallbacks that SCTP has for identifying an association for an
incoming packet, it looks for AddIp chunk (from ASCONF) and take a peek.
Thing is, at this stage nothing was validating that the chunk actually had
enough content for that, allowing the peek to happen over uninitialized
memory.
Similar check already exists in actual asconf handling in
sctp_verify_asconf().
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fcf044891c upstream.
We do not need a SWIOTLB unless we have DRAM that is addressable beyond
the arm_dma_limit. Compare max_pfn with arm_dma_pfn_limit to determine
whether we do need a SWIOTLB to be initialized.
Fixes: ad3c7b18c5 ("arm: use swiotlb for bounce buffering on LPAE configs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8b92b8c1e upstream.
We should not walk/touch page tables outside of VMA boundaries when
holding only the mmap sem in read mode. Evil user space can modify the
VMA layout just before this function runs and e.g., trigger races with
page table removal code since commit dd2283f260 ("mm: mmap: zap pages
with read mmap_sem in munmap").
find_vma() does not check if the address is >= the VMA start address;
use vma_lookup() instead.
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Fixes: dd2283f260 ("mm: mmap: zap pages with read mmap_sem in munmap")
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a2b2eb556 upstream.
The Linux console's VT102 implementation already consumes OSC
("Operating System Command") sequences, probably because that's how
palette changes are transmitted.
In addition to OSC, there are three other major clases of ANSI control
strings: APC ("Application Program Command"), PM ("Privacy Message"),
and DCS ("Device Control String"). They are handled similarly to OSC in
terms of termination.
Source: vt100.net
Add three new enumerated states, one for each of these types. All three
are handled the same way right now--they simply consume input until
terminated. I hope to expand upon this firmament in the future. Add
new predicate ansi_control_string(), returning true for any of these
states. Replace explicit checks against ESosc with calls to this
function. Transition to these states appropriately from the escape
initiation (ESesc) state.
This was motivated by the following Notcurses bugs:
https://github.com/dankamongmen/notcurses/issues/2050https://github.com/dankamongmen/notcurses/issues/1828https://github.com/dankamongmen/notcurses/issues/2069
where standard VT sequences are not consumed by the Linux console. It's
not necessary that the Linux console *support* these sequences, but it
ought *consume* these well-specified classes of sequences.
Tested by sending a variety of escape sequences to the console, and
verifying that they still worked, or were now properly consumed.
Verified that the escapes were properly terminated at a generic level.
Verified that the Notcurses tools continued to show expected output on
the Linux console, except now without escape bleedthrough.
Link: https://lore.kernel.org/lkml/YSydL0q8iaUfkphg@schwarzgerat.orthanc/
Signed-off-by: nick black <dankamongmen@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 02319bf15a upstream.
After d12e1c4649 ("net: dsa: b53: Set correct number of ports in the
DSA struct") we stopped setting dsa_switch::num_ports to DSA_MAX_PORTS,
which created an off by one error between the statically allocated
bcm_sf2_priv::port_sts array (of size DSA_MAX_PORTS). When
dsa_is_cpu_port() is used, we end-up accessing an out of bounds member
and causing a NPD.
Fix this by iterating with the appropriate port count using
ds->num_ports.
Fixes: d12e1c4649 ("net: dsa: b53: Set correct number of ports in the DSA struct")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eca4cf12ac upstream.
The recent patch has introduced a regression by not reading the reset
count in the ERROR_RECOVERY async event handler. We may have just
gone through a reset and the reset count has just incremented. If
we don't update the reset count in the ERROR_RECOVERY event handler,
the health check timer will see that the reset count has changed and
will initiate an unintended reset.
Restore the unconditional update of the reset count in
bnxt_async_event_process() if error recovery watchdog is enabled.
Also, update the reset count at the end of the reset sequence to
make it even more robust.
Fixes: 1b2b918319 ("bnxt_en: Fix possible unintended driver initiated error recovery")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81065b35e2 upstream.
There are two cases for machine check recovery:
1) The machine check was triggered by ring3 (application) code.
This is the simpler case. The machine check handler simply queues
work to be executed on return to user. That code unmaps the page
from all users and arranges to send a SIGBUS to the task that
triggered the poison.
2) The machine check was triggered in kernel code that is covered by
an exception table entry. In this case the machine check handler
still queues a work entry to unmap the page, etc. but this will
not be called right away because the #MC handler returns to the
fix up code address in the exception table entry.
Problems occur if the kernel triggers another machine check before the
return to user processes the first queued work item.
Specifically, the work is queued using the ->mce_kill_me callback
structure in the task struct for the current thread. Attempting to queue
a second work item using this same callback results in a loop in the
linked list of work functions to call. So when the kernel does return to
user, it enters an infinite loop processing the same entry for ever.
There are some legitimate scenarios where the kernel may take a second
machine check before returning to the user.
1) Some code (e.g. futex) first tries a get_user() with page faults
disabled. If this fails, the code retries with page faults enabled
expecting that this will resolve the page fault.
2) Copy from user code retries a copy in byte-at-time mode to check
whether any additional bytes can be copied.
On the other side of the fence are some bad drivers that do not check
the return value from individual get_user() calls and may access
multiple user addresses without noticing that some/all calls have
failed.
Fix by adding a counter (current->mce_count) to keep track of repeated
machine checks before task_work() is called. First machine check saves
the address information and calls task_work_add(). Subsequent machine
checks before that task_work call back is executed check that the address
is in the same page as the first machine check (since the callback will
offline exactly one page).
Expected worst case is four machine checks before moving on (e.g. one
user access with page faults disabled, then a repeat to the same address
with page faults enabled ... repeat in copy tail bytes). Just in case
there is some code that loops forever enforce a limit of 10.
[ bp: Massage commit message, drop noinstr, fix typo, extend panic
messages. ]
Fixes: 5567d11c21 ("x86/mce: Send #MC singal from task work")
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/YT/IJ9ziLqmtqEPu@agluck-desk2.amr.corp.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0341d5e3d1 ]
The cur_tx counter must be incremented after TACT bit of
txdesc->status was set. However, a CPU is possible to reorder
instructions and/or memory accesses between cur_tx and
txdesc->status. And then, if TX interrupt happened at such a
timing, the sh_eth_tx_free() may free the descriptor wrongly.
So, add wmb() before cur_tx++.
Otherwise NETDEV WATCHDOG timeout is possible to happen.
Fixes: 86a74ff21a ("net: sh_eth: add support for Renesas SuperH Ethernet")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdff1eda69 ]
One MIPS platform (mach-rc32434) defines GPIOBASE. This macro
conflicts with one of the same name in lpc_sch.c. Rename the latter one
to prevent the build error.
../drivers/mfd/lpc_sch.c:25: error: "GPIOBASE" redefined [-Werror]
25 | #define GPIOBASE 0x44
../arch/mips/include/asm/mach-rc32434/rb.h:32: note: this is the location of the previous definition
32 | #define GPIOBASE 0x050000
Cc: Denis Turischev <denis@compulab.co.il>
Fixes: e82c60ae7d ("mfd: Introduce lpc_sch for Intel SCH LPC bridge")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 922e8ce883 ]
The IRQ support for SCH GPIO is not specific to the Intel Quark SoC.
Moreover the IRQ routing is quite interesting there, so while it's
needs a special support, the driver haven't it anyway yet.
Due to above remove basically redundant code of IRQ support.
This reverts commit ec689a8a81.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b2b918319 ]
If error recovery is already enabled, bnxt_timer() will periodically
check the heartbeat register and the reset counter. If we get an
error recovery async. notification from the firmware (e.g. change in
primary/secondary role), we will immediately read and update the
heartbeat register and the reset counter. If the timer for the next
health check expires soon after this, we may read the heartbeat register
again in quick succession and find that it hasn't changed. This will
trigger error recovery unintentionally.
The likelihood is small because we also reset fw_health->tmr_counter
which will reset the interval for the next health check. But the
update is not protected and bnxt_timer() can miss the update and
perform the health check without waiting for the full interval.
Fix it by only reading the heartbeat register and reset counter in
bnxt_async_event_process() if error recovery is trasitioning to the
enabled state. Also add proper memory barriers so that when enabling
for the first time, bnxt_timer() will see the tmr_counter interval and
perform the health check after the full interval has elapsed.
Fixes: 7e914027f7 ("bnxt_en: Enable health monitoring.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4d95c3c19 ]
We currently only log the error recovery settings if it is enabled.
In some cases, firmware disables error recovery after it was
initially enabled. Without logging anything, the user will not be
aware of this change in setting.
Log it when error recovery is disabled. Also, change the reset count
value from hexadecimal to decimal.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a44daa8fcb ]
Firmware is capable of generating asynchronous debug notifications.
The event data is opaque to the driver and is simply logged. Debug
notifications can be enabled by turning on hardware status messages
using the ethtool msglvl interface.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6fdab8a3ad ]
The current asic.rev is incomplete and does not include the metal
revision. Add the metal revision and decode the complete asic
revision into the more common and readable form (A0, B0, etc).
Fixes: 7154917a12 ("bnxt_en: Refactor bnxt_dl_info_get().")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63f8428b40 ]
Broadcom's b53 switches have one IMP (Inband Management Port) that needs
to be programmed using its own designed register. IMP port may be
different than CPU port - especially on devices with multiple CPU ports.
For that reason it's required to explicitly note IMP port index and
check for it when choosing a register to use.
This commit fixes BCM5301x support. Those switches use CPU port 5 while
their IMP port is 8. Before this patch b53 was trying to program port 5
with B53_PORT_OVERRIDE_CTRL instead of B53_GMII_PORT_OVERRIDE_CTRL(5).
It may be possible to also replace "cpu_port" usages with
dsa_is_cpu_port() but that is out of the scope of thix BCM5301x fix.
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a0ed250f9 ]
The GRE tunnel device can pull existing outer headers in ipge_xmit.
This is a rare path, apparently unique to this device. The below
commit ensured that pulling does not move skb->data beyond csum_start.
But it has a false positive if ip_summed is not CHECKSUM_PARTIAL and
thus csum_start is irrelevant.
Refine to exclude this. At the same time simplify and strengthen the
test.
Simplify, by moving the check next to the offending pull, making it
more self documenting and removing an unnecessary branch from other
code paths.
Strengthen, by also ensuring that the transport header is correct and
therefore the inner headers will be after skb_reset_inner_headers.
The transport header is set to csum_start in skb_partial_csum_set.
Link: https://lore.kernel.org/netdev/YS+h%2FtqCJJiQei+W@shredder/
Fixes: 1d011c4803 ("ip_gre: add validation for csum_start")
Reported-by: Ido Schimmel <idosch@idosch.org>
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ddbc2a00d ]
Previous commit 68233c583a removes the qlcnic_rom_lock()
in qlcnic_pinit_from_rom(), but remains its corresponding
unlock function, which is odd. I'm not very sure whether the
lock is missing, or the unlock is redundant. This bug is
suggested by a static analysis tool, please advise.
Fixes: 68233c583a ("qlcnic: updated reset sequence")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7c5e6ff53 ]
syzbot found that forcing a big quantum attribute would crash hosts fast,
essentially using this:
tc qd replace dev eth0 root fq_codel quantum 4294967295
This is because fq_codel_dequeue() would have to loop
~2^31 times in :
if (flow->deficit <= 0) {
flow->deficit += q->quantum;
list_move_tail(&flow->flowchain, &q->old_flows);
goto begin;
}
SFQ max quantum is 2^19 (half a megabyte)
Lets adopt a max quantum of one megabyte for FQ_CODEL.
Fixes: 4b549a2ef4 ("fq_codel: Fair Queue Codel AQM")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 730affed24 ]
Bug reported by KASAN:
BUG: KASAN: use-after-scope in inet6_ehashfn (net/ipv6/inet6_hashtables.c:40)
Call Trace:
(...)
inet6_ehashfn (net/ipv6/inet6_hashtables.c:40)
(...)
nf_sk_lookup_slow_v6 (net/ipv6/netfilter/nf_socket_ipv6.c:91
net/ipv6/netfilter/nf_socket_ipv6.c:146)
It seems that this bug has already been fixed by Eric Dumazet in the
past in:
commit 78296c97ca ("netfilter: xt_socket: fix a stack corruption bug")
But a variant of the same issue has been introduced in
commit d64d80a2cd ("netfilter: x_tables: don't extract flow keys on early demuxed sks in socket match")
`daddr` and `saddr` potentially hold a reference to ipv6_var that is no
longer in scope when the call to `nf_socket_get_sock_v6` is made.
Fixes: d64d80a2cd ("netfilter: x_tables: don't extract flow keys on early demuxed sks in socket match")
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Benjamin Hesmans <benjamin.hesmans@tessares.net>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d12e1c4649 ]
Setting DSA_MAX_PORTS caused DSA to call b53 callbacks (e.g.
b53_disable_port() during dsa_register_switch()) for invalid
(non-existent) ports. That made b53 modify unrelated registers and is
one of reasons for a broken BCM5301x support.
This problem exists for years but DSA_MAX_PORTS usage has changed few
times. It seems the most accurate to reference commit dropping
dsa_switch_alloc() in the Fixes tag.
Fixes: 7e99e34701 ("net: dsa: remove dsa_switch_alloc helper")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdb067d31c ]
It isn't true that CPU port is always the last one. Switches BCM5301x
have 9 ports (port 6 being inactive) and they use port 5 as CPU by
default (depending on design some other may be CPU ports too).
A more reliable way of determining number of ports is to check for the
last set bit in the "enabled_ports" bitfield.
This fixes b53 internal state, it will allow providing accurate info to
the DSA and is required to fix BCM5301x support.
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ecdc28defc ]
If the network devices connected to the system beyond
HSO_MAX_NET_DEVICES. add_net_device() in hso_create_net_device()
will be failed for the network_table is full. It will lead to
business failure which rely on network_table, for example,
hso_suspend() and hso_resume(). It will also lead to memory leak
because resource release process can not search the hso_device
object from network_table in hso_free_interface().
Add failure handler for add_net_device() in hso_create_net_device()
to solve the above problems.
Fixes: 72dc1c096c ("HSO: add option hso driver")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfd862a7e9 ]
'$cin' and '$sin' variables are local to a function: they are then not
available from the cleanup trap.
Instead, we need to use '$large' and '$small' that are not local and
defined just before setting the trap.
Without this patch, running this script in a loop might cause a:
write: No space left on device
issue.
Fixes: 1a418cb8e8 ("mptcp: simult flow self-tests")
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e90dfa7a8 ]
I noticed that only port 0 worked on the RTL8366RB since we
started to use custom tags.
It turns out that the format of egress custom tags is actually
different from ingress custom tags. While the lower bits just
contain the port number in ingress tags, egress tags need to
indicate destination port by setting the bit for the
corresponding port.
It was working on port 0 because port 0 added 0x00 as port
number in the lower bits, and if you do this the packet appears
at all ports, including the intended port. Ooops.
Fix this and all ports work again. Use the define for shifting
the "type A" into place while we're at it.
Tested on the D-Link DIR-685 by sending traffic to each of
the ports in turn. It works.
Fixes: 86dd9868b8 ("net: dsa: tag_rtl4_a: Support also egress tags")
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 889a1b3f35 ]
If an error occurs after a 'gpiochip_add_data()' call it must be undone by
a corresponding 'gpiochip_remove()' as already done in the remove function.
To simplify the code a fix a leak in the error handling path of the probe,
use the managed version instead (i.e. 'devm_gpiochip_add_data()')
Fixes: 698b8eeaed ("gpio/mpc8xxx: change irq handler from chained to normal")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 555bda42b0 ]
Commit 698b8eeaed ("gpio/mpc8xxx: change irq handler from chained to normal")
has introduced a new 'goto err;' at the very end of the function, but has
not updated the error handling path accordingly.
Add the now missing 'irq_domain_remove()' call which balances a previous
'irq_domain_create_linear() call.
Fixes: 698b8eeaed ("gpio/mpc8xxx: change irq handler from chained to normal")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit edf7b4a2d8 ]
The build on fedora:35 and fedora:rawhide with clang is failing with:
49 41.00 fedora:35 : FAIL clang version 13.0.0 (Fedora 13.0.0~rc1-1.fc35)
bench/inject-buildid.c:351:6: error: variable 'len' set but not used [-Werror,-Wunused-but-set-variable]
u64 len = 0;
^
1 error generated.
make[3]: *** [/git/perf-5.14.0-rc7/tools/build/Makefile.build:139: bench] Error 2
50 41.11 fedora:rawhide : FAIL clang version 13.0.0 (Fedora 13.0.0~rc1-1.fc35)
bench/inject-buildid.c:351:6: error: variable 'len' set but not used [-Werror,-Wunused-but-set-variable]
u64 len = 0;
^
1 error generated.
make[3]: *** [/git/perf-5.14.0-rc7/tools/build/Makefile.build:139: bench] Error 2
That 'len' variable is not used at all, so just make sure all the
synthesize_RECORD() routines return ssize_t to propagate the writen()
return, as it may fail, ditch the 'ret' var and bail out if those
routines fail.
Fixes: 0bf02a0d80 ("perf bench: Add build-id injection benchmark")
Acked-by: Namhyung Kim <namhyung@kernel.org>
Link: http://lore.kernel.org/lkml/CAM9d7cgEZNSor+B+7Y2C+QYGme_v5aH0Zn0RLfxoQ+Fy83EHrg@mail.gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b5ff0405e ]
0day bot reports a build error:
ERROR: modpost: "clear_user_page" [drivers/media/v4l2-core/videobuf-dma-sg.ko] undefined!
so export it in arch/arc/ to fix the build error.
In most ARCHes, clear_user_page() is a macro. OTOH, in a few
ARCHes it is a function and needs to be exported.
PowerPC exported it in 2004. It looks like nds32 and nios2
still need to have it exported.
Fixes: 4102b53392 ("ARC: [mm] Aliasing VIPT dcache support 2/4")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-snps-arc@lists.infradead.org
Signed-off-by: Vineet Gupta <vgupta@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6826c6849b ]
The CPU_ON PSCI call takes a payload that KVM uses to configure a
destination vCPU to run. This payload is non-architectural state and not
exposed through any existing UAPI. Effectively, we have a race between
CPU_ON and userspace saving/restoring a guest: if the target vCPU isn't
ran again before the VMM saves its state, the requested PC and context
ID are lost. When restored, the target vCPU will be runnable and start
executing at its old PC.
We can avoid this race by making sure the reset payload is serviced
before userspace can access a vCPU's state.
Fixes: 358b28f09f ("arm/arm64: KVM: Allow a VCPU to fully reset itself")
Signed-off-by: Oliver Upton <oupton@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210818202133.1106786-3-oupton@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6654f9dfcb ]
KVM correctly serializes writes to a vCPU's reset state, however since
we do not take the KVM lock on the read side it is entirely possible to
read state from two different reset requests.
Cure the race for now by taking the KVM lock when reading the
reset_state structure.
Fixes: 358b28f09f ("arm/arm64: KVM: Allow a VCPU to fully reset itself")
Signed-off-by: Oliver Upton <oupton@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210818202133.1106786-2-oupton@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a89d69a44e ]
Since 2431c4f5b4 ("mtd: Implement mtd_{read,write}() as wrappers
around mtd_{read,write}_oob()") don't allow _write|_read and
_write_oob|_read_oob existing at the same time, we should check the
existence of callbacks "_read and _write" from subdev's master device
(We can trust master device since it has been registered) before
assigning, otherwise following warning occurs while making
concatenated device:
WARNING: CPU: 2 PID: 6728 at drivers/mtd/mtdcore.c:595
add_mtd_device+0x7f/0x7b0
Fixes: 2431c4f5b4 ("mtd: Implement mtd_{read,write}() around ...")
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210817114857.2784825-3-chengzhihao1@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a946506c48 ]
The driver was registering IRQ 0 when no IRQ was set. This leads to
warnings with newer kernels.
Clear the resource flags, so no resource is registered at all in this
case.
Fixes: 2f17dd34ff ("mfd: tqmx86: IO controller with I2C, Wachdog and GPIO")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3245a7b7b ]
Syzbot hit use-after-free in nf_tables_dump_sets. The problem was in
missing lock protection for nft_ct_pcpu_template_refcnt.
Before commit f102d66b33 ("netfilter: nf_tables: use dedicated
mutex to guard transactions") all transactions were serialized by global
mutex, but then global mutex was changed to local per netnamespace
commit_mutex.
This change causes use-after-free bug, when 2 netnamespaces concurently
changing nft_ct_pcpu_template_refcnt without proper locking. Fix it by
adding nft_ct_pcpu_mutex and protect all nft_ct_pcpu_template_refcnt
changes with it.
Fixes: f102d66b33 ("netfilter: nf_tables: use dedicated mutex to guard transactions")
Reported-and-tested-by: syzbot+649e339fa6658ee623d3@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit daa3736151 ]
Remove interrupt disablement during backlight setting. It is
way to dangerous and makes platforms instable by having it
miss vblank IRQs leading to the graphics derailing.
The code is using ndelay() which is not available on
platforms such as ARM and will result in 32 * udelay(1)
which is substantial.
Add some code to detect if an interrupt occurs during the
tight loop and in that case just redo it from the top.
Fixes: 5317f37e48 ("backlight: Add Kinetic KTD253 backlight driver")
Cc: Stephan Gerhold <stephan@gerhold.net>
Reported-by: newbyte@disroot.org
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f949a9ebce ]
On Cherry Trail devices with an AXP288 PMIC the external SD-card slot
used the AXP's DLDO2 as card-voltage and either DLDO3 or GPIO1LDO
(GPIO1 pin in low noise LDO mode) as signal-voltage.
These regulators are turned on/off and in case of the signal-voltage
also have their output-voltage changed by the _PS0 and _PS3 power-
management ACPI methods on the MMC-controllers ACPI fwnode as well as
by the _DSM ACPI method for changing the signal voltage.
The AML code implementing these methods is directly accessing the
PMIC through ACPI I2C OpRegion accesses, instead of using the special
PMIC OpRegion handled by drivers/acpi/pmic/intel_pmic_xpower.c .
This means that the contents of the involved PMIC registers can change
without the change being made through the regmap interface, so regmap
should not cache the contents of these registers.
Mark the regulator power on/off, the regulator voltage control and the
GPIO1 control registers as volatile, to avoid regmap caching them.
Specifically this fixes an issue on some models where the i915 driver
toggles another LDO using the same on/off register on/off through
MIPI sequences (through intel_soc_pmic_exec_mipi_pmic_seq_element())
which then writes back a cached on/off register-value where the
card-voltage is off causing the external sdcard slot to stop working
when the screen goes blank, or comes back on again.
The regulator register-range now marked volatile also includes the
buck regulator control registers. This is done on purpose these are
normally not touched by the AML code, but they are updated directly
by the SoC's PUNIT which means that they may also change without going
through regmap.
Note the AXP288 PMIC is only used on Bay- and Cherry-Trail platforms,
so even though this is an ACPI specific problem there is no need to
make the new volatile ranges conditional since these platforms always
use ACPI.
Fixes: dc91c3b6fe ("mfd: axp20x: Mark AXP20X_VBUS_IPSOUT_MGMT as volatile")
Fixes: cd53216625 ("mfd: axp20x: Fix axp288 volatile ranges")
Reported-and-tested-by: Clamshell <clamfly@163.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1511df6f5e upstream.
EMIT6_PCREL() macro assumes that the previous pass generated 6 bytes
of code, which is not the case if branch shortening took place. Fix by
using jit->prg, like all the other EMIT6_PCREL_*() macros.
Reported-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Fixes: 4e9b4a6883 ("s390/bpf: Use relative long branches")
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e61dc9da0 upstream.
The JIT uses agfi for subtracting constants, but -(-0x80000000) cannot
be represented as a 32-bit signed binary integer. Fix by using algfi in
this particular case.
Reported-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Fixes: 0546231057 ("s390/bpf: Add s390x eBPF JIT compiler backend")
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db7bee6538 upstream.
Currently the JIT completely removes things like `reg32 += 0`,
however, the BPF_ALU semantics requires the target register to be
zero-extended in such cases.
Fix by optimizing out only the arithmetic operation, but not the
subsequent zero-extension.
Reported-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Fixes: 0546231057 ("s390/bpf: Add s390x eBPF JIT compiler backend")
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0097ae5f7a ]
When the function IS_ALIGNED() returns false, the value of ret is 0.
So, we set ret to -EINVAL to indicate this error.
Clean up smatch warning:
drivers/ntb/test/ntb_perf.c:602 perf_setup_inbuf() warn: missing error
code 'ret'.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 319f83ac98 ]
When the value of nm->isr_ctx is false, the value of ret is 0.
So, we set ret to -ENOMEM to indicate this error.
Clean up smatch warning:
drivers/ntb/test/ntb_msi_test.c:373 ntb_msit_probe() warn: missing
error code 'ret'.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7db8263a12 ]
When adapter->registered_device_map is NULL, the value of err is
uncertain, we set err to -EINVAL to avoid ambiguity.
Clean up smatch warning:
drivers/net/ethernet/chelsio/cxgb/cxgb2.c:1114 init_one() warn: missing
error code 'err'
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d52c58b9c ]
The function bfq_setup_merge prepares the merging between two
bfq_queues, say bfqq and new_bfqq. To this goal, it assigns
bfqq->new_bfqq = new_bfqq. Then, each time some I/O for bfqq arrives,
the process that generated that I/O is disassociated from bfqq and
associated with new_bfqq (merging is actually a redirection). In this
respect, bfq_setup_merge increases new_bfqq->ref in advance, adding
the number of processes that are expected to be associated with
new_bfqq.
Unfortunately, the stable-merging mechanism interferes with this
setup. After bfqq->new_bfqq has been set by bfq_setup_merge, and
before all the expected processes have been associated with
bfqq->new_bfqq, bfqq may happen to be stably merged with a different
queue than the current bfqq->new_bfqq. In this case, bfqq->new_bfqq
gets changed. So, some of the processes that have been already
accounted for in the ref counter of the previous new_bfqq will not be
associated with that queue. This creates an unbalance, because those
references will never be decremented.
This commit fixes this issue by reestablishing the previous, natural
behaviour: once bfqq->new_bfqq has been set, it will not be changed
until all expected redirections have occurred.
Signed-off-by: Davide Zini <davidezini2@gmail.com>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Link: https://lore.kernel.org/r/20210802141352.74353-2-paolo.valente@linaro.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aabbdc67f3 ]
Add quirk CDC_MBIM_FLAG_AVOID_ALTSETTING_TOGGLE for Telit LN920
0x1061 composition in order to avoid bind error.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21274aa178 ]
Check one more time before exiting the API with an error.
Fix API to poll at least twice, in case there are other high priority
tasks and this API doesn't get CPU cycles for multiple jiffies update.
In addition, increase timeout from usecs_to_jiffies(10000) to
usecs_to_jiffies(20000), to prevent the case that for CONFIG_100HZ
timeout will be a single jiffies.
A single jiffies results actual timeout that can be any time between
1usec and 10msec. To solve this, a value of usecs_to_jiffies(20000)
ensures that timeout is 2 jiffies.
Signed-off-by: Smadar Fuks <smadarf@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dbe80cf471 ]
We must not pet a running watchdog when handle_boot_enabled is off
because this will kick off automatic triggering before userland is
running, defeating the purpose of the handle_boot_enabled control.
Furthermore, don't ping in case watchdog_set_last_hw_keepalive was
called incorrectly when the hardware watchdog is actually not running.
Fixed: cef9572e9a ("watchdog: add support for adjusting last known HW keepalive time")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/93d56386-6e37-060b-55ce-84de8cde535f@web.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 32837d8a8f ]
Some Cavium endpoints are implemented as multi-function devices without ACS
capability, but they actually don't support peer-to-peer transactions.
Add ACS quirks to declare DMA isolation for the following devices:
- BGX device found on Octeon-TX (8xxx)
- CGX device found on Octeon-TX2 (9xxx)
- RPM device found on Octeon-TX3 (10xxx)
Link: https://lore.kernel.org/r/20210810122425.1115156-1-george.cherian@marvell.com
Signed-off-by: George Cherian <george.cherian@marvell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1de58802f ]
J7200 has the same PCIe IP as in J721E with minor changes in the
wrapper. J7200 allows byte access of bridge configuration space
registers and the register field for LINK_DOWN interrupt is different.
J7200 also requires "quirk_detect_quiet_flag" to be set. Configure these
changes as part of driver data applicable only to J7200.
Link: https://lore.kernel.org/r/20210811123336.31357-4-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09c24094b2 ]
PCIe fails to link up if SERDES lanes not used by PCIe are assigned to
another protocol. For example, link training fails if lanes 2 and 3 are
assigned to another protocol while lanes 0 and 1 are used for PCIe to
form a two lane link. This failure is due to an incorrect tie-off on an
internal status signal indicating electrical idle.
Status signals going from SERDES to PCIe Controller are tied-off when a
lane is not assigned to PCIe. Signal indicating electrical idle is
incorrectly tied-off to a state that indicates non-idle. As a result,
PCIe sees unused lanes to be out of electrical idle and this causes
LTSSM to exit Detect.Quiet state without waiting for 12ms timeout to
occur. If a receiver is not detected on the first receiver detection
attempt in Detect.Active state, LTSSM goes back to Detect.Quiet and
again moves forward to Detect.Active state without waiting for 12ms as
required by PCIe base specification. Since wait time in Detect.Quiet is
skipped, multiple receiver detect operations are performed back-to-back
without allowing time for capacitance on the transmit lines to
discharge. This causes subsequent receiver detection to always fail even
if a receiver gets connected eventually.
Add a quirk flag "quirk_detect_quiet_flag" to program the minimum
time the LTSSM should wait on entering Detect.Quiet state here.
This has to be set for J7200 as it has an incorrect tie-off on unused
lanes.
Link: https://lore.kernel.org/r/20210811123336.31357-3-kishon@ti.com
Signed-off-by: Nadeem Athani <nadeem@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e242060c6 ]
Since kprobe_events and uprobe_events only check whether the
other same-type probe event has the same name or not, if the
user gives the same name of the existing tracepoint event (or
the other type of probe events), it silently fails to create
the tracefs entry (but registered.) as below.
/sys/kernel/tracing # ls events/task/task_rename
enable filter format hist id trigger
/sys/kernel/tracing # echo p:task/task_rename vfs_read >> kprobe_events
[ 113.048508] Could not create tracefs 'task_rename' directory
/sys/kernel/tracing # cat kprobe_events
p:task/task_rename vfs_read
To fix this issue, check whether the existing events have the
same name or not in trace_probe_register_event_call(). If exists,
it rejects to register the new event.
Link: https://lkml.kernel.org/r/162936876189.187130.17558311387542061930.stgit@devnote2
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ff80e2de3 ]
Although irq_create_mapping() is able to deal with duplicate
mappings, it really isn't supposed to be a substitute for
irq_find_mapping(), and can result in allocations that take place
in atomic context if the mapping didn't exist.
Fix the handful of MFD drivers that use irq_create_mapping() in
interrupt context by using irq_find_mapping() instead.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1e71c1688 ]
There is a potential race between fuse_read_interrupt() and
fuse_request_end().
TASK1
in fuse_read_interrupt(): delete req->intr_entry (while holding
fiq->lock)
TASK2
in fuse_request_end(): req->intr_entry is empty -> skip fiq->lock
wake up TASK3
TASK3
request is freed
TASK1
in fuse_read_interrupt(): dereference req->in.h.unique ***BAM***
Fix by always grabbing fiq->lock if the request was ever interrupted
(FR_INTERRUPTED set) thereby serializing with concurrent
fuse_read_interrupt() calls.
FR_INTERRUPTED is set before the request is queued on fiq->interrupts.
Dequeing the request is done with list_del_init() but FR_INTERRUPTED is not
cleared in this case.
Reported-by: lijiazi <lijiazi@xiaomi.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec343111c0 ]
These are the actual frequencies reported by the PLL, so let's
report these. The roundoffs are inappropriate, we should round
to the frequency that the clock will later report.
Drop some whitespace at the same time.
Cc: phone-devel@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 427900d27d upstream.
Currently, the VF does not clear the interrupt source immediately after
receiving the interrupt. As a result, if the second interrupt task is
triggered when processing the first interrupt task, clearing the
interrupt source before exiting will clear the interrupt sources of the
two tasks at the same time. As a result, no interrupt is triggered for
the second task. The VF detects the missed message only when the next
interrupt is generated.
Clearing it immediately after executing check_evt_cause ensures that:
1. Even if two interrupt tasks are triggered at the same time, they can
be processed.
2. If the second task is triggered during the processing of the first
task and the interrupt source is not cleared, the interrupt is reported
after vector0 is enabled.
Fixes: b90fcc5bd9 ("net: hns3: add reset handling for VF when doing Core/Global/IMP reset")
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b81d894874 upstream.
The firmware will not disable mac in flr process. Therefore, the driver
needs to proactively disable mac during flr, which is the same as the
function reset.
Fixes: 35d93a3004 ("net: hns3: adjust the process of PF reset")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1dc839ec09 upstream.
Currently, affinity_mask is set to a single cpu. As a result,
irqbalance becomes invalid in SUBSET or EXACT mode. To solve
this problem, change affinity_mask to numa node range. In this
way, irqbalance can be performed on the cpu of the numa node.
Fixes: 0812545487 ("net: hns3: add interrupt affinity support for misc interrupt")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d18e81183b upstream.
The hardware cannot handle short tunnel frames below 65 bytes,
and will cause vlan tag missing problem. So pads packet size to
65 bytes for tunnel frames to fix this bug.
Fixes: 3db084d28dc0("net: hns3: Fix for vxlan tx checksum bug")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1affc01fdc upstream.
The call to bnxt_free_mem(..., false) in the bnxt_half_open_nic() error
path will deallocate ring descriptor memory via bnxt_free_?x_rings(),
but because irq_re_init is false, the ring info itself is not freed.
To simplify error paths, deallocation functions have generally been
written to be safe when called on unallocated memory. It should always
be safe to call dev_close(), which calls bnxt_free_skbs() a second time,
even in this semi- allocated ring state.
Calling bnxt_free_skbs() a second time with the rings already freed will
cause NULL pointer dereference. Fix it by checking the rings are valid
before proceeding in bnxt_free_tx_skbs() and
bnxt_free_one_rx_ring_skbs().
Fixes: 975bc99a4a ("bnxt_en: Refactor bnxt_free_rx_skbs().")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 267cdfa213 upstream.
POWER9 DD2.2 and 2.3 hardware implements a "fake-suspend" mode where
certain TM instructions executed in HV=0 mode cause softpatch interrupts
so the hypervisor can emulate them and prevent problematic processor
conditions. In this fake-suspend mode, the treclaim. instruction does
not modify registers.
Unfortunately the rfscv instruction executed by the guest do not
generate softpatch interrupts, which can cause the hypervisor to lose
track of the fake-suspend mode, and it can execute this treclaim. while
not in fake-suspend mode. This modifies GPRs and crashes the hypervisor.
It's not trivial to disable scv in the guest with HFSCR now, because
they assume a POWER9 has scv available. So this fix saves and restores
checkpointed registers across the treclaim.
Fixes: 7854f7545b ("KVM: PPC: Book3S: Rework TM save/restore code and make it C-callable")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210908101718.118522-2-npiggin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 273c29e944 upstream.
If a failover occurs before a login response is received, the login
response buffer maybe undefined. Check that there was no failover
before accessing the login response buffer.
Fixes: 032c5e8284 ("Driver for IBM System i/p VNIC protocol")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e50e711351 upstream.
Turn udp_tunnel_nic work-queue to an ordered work-queue. This queue
holds the UDP-tunnel configuration commands of the different netdevs.
When the netdevs are functions of the same NIC the order of
execution may be crucial.
Problem example:
NIC with 2 PFs, both PFs declare offload quota of up to 3 UDP-ports.
$ifconfig eth2 1.1.1.1/16 up
$ip link add eth2_19503 type vxlan id 5049 remote 1.1.1.2 dev eth2 dstport 19053
$ip link set dev eth2_19503 up
$ip link add eth2_19504 type vxlan id 5049 remote 1.1.1.3 dev eth2 dstport 19054
$ip link set dev eth2_19504 up
$ip link add eth2_19505 type vxlan id 5049 remote 1.1.1.4 dev eth2 dstport 19055
$ip link set dev eth2_19505 up
$ip link add eth2_19506 type vxlan id 5049 remote 1.1.1.5 dev eth2 dstport 19056
$ip link set dev eth2_19506 up
NIC RX port offload infrastructure offloads the first 3 UDP-ports (on
all devices which sets NETIF_F_RX_UDP_TUNNEL_PORT feature) and not
UDP-port 19056. So both PFs gets this offload configuration.
$ip link set dev eth2_19504 down
This triggers udp-tunnel-core to remove the UDP-port 19504 from
offload-ports-list and offload UDP-port 19056 instead.
In this scenario it is important that the UDP-port of 19504 will be
removed from both PFs before trying to add UDP-port 19056. The NIC can
stop offloading a UDP-port only when all references are removed.
Otherwise the NIC may report exceeding of the offload quota.
Fixes: cc4e3835ef ("udp_tunnel: add central NIC RX port offload infrastructure")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 20e100f527 upstream.
Handle MFW (management FW) error response in order to avoid a crash
during recovery flows.
Changes from v1:
- Add "Fixes tag".
Fixes: tag 5e7ba042fd ("qed: Fix reading stale configuration information")
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b704b27be upstream.
If altname deletion of the short alternative name fails, the error
message printed is: "Failed to add short alternative name".
This is obviously a typo, as we are testing altname deletion.
Fix this using a proper error message.
Fixes: f95e6c9c46 ("selftest: net: add alternative names test")
Signed-off-by: Andrea Claudi <aclaudi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f884f3962 upstream.
Commit 10d3be5692 ("tcp-tso: do not split TSO packets at retransmit
time") may directly retrans a multiple segments TSO/GSO packet without
split, Since this commit, we can no longer assume that a retransmitted
packet is a single segment.
This patch fixes the tp->undo_retrans accounting in tcp_sacktag_one()
that use the actual segments(pcount) of the retransmitted packet.
Before that commit (10d3be5692), the assumption underlying the
tp->undo_retrans-- seems correct.
Fixes: 10d3be5692 ("tcp-tso: do not split TSO packets at retransmit time")
Signed-off-by: zhenggy <zhenggy@chinatelecom.cn>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a69ae291e1 upstream.
Commit 865c50e1d2 ("x86/uaccess: utilize CONFIG_CC_HAS_ASM_GOTO_OUTPUT")
added an optimised version of __get_user_asm() for x86 using 'asm goto'.
Like the non-optimised code, the 32-bit implementation of 64-bit
get_user() expands to a pair of 32-bit accesses. Unlike the
non-optimised code, the _original_ pointer is incremented to copy the
high word instead of loading through a new pointer explicitly
constructed to point at a 32-bit type. Consequently, if the pointer
points at a 64-bit type then we end up loading the wrong data for the
upper 32-bits.
This was observed as a mount() failure in Android targeting i686 after
b0cfcdd9b9 ("d_path: make 'prepend()' fill up the buffer exactly on
overflow") because the call to copy_from_kernel_nofault() from
prepend_copy() ends up in __get_kernel_nofault() and casts the source
pointer to a 'u64 __user *'. An attempt to mount at "/debug_ramdisk"
therefore ends up failing trying to mount "/debumdismdisk".
Use the existing '__gu_ptr' source pointer to unsigned int for 32-bit
__get_user_asm_u64() instead of the original pointer.
Cc: Bill Wendling <morbo@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 865c50e1d2 ("x86/uaccess: utilize CONFIG_CC_HAS_ASM_GOTO_OUTPUT")
Signed-off-by: Will Deacon <will@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6a52e73368 upstream.
DSA supports connecting to a phy-handle, and has a fallback to a non-OF
based method of connecting to an internal PHY on the switch's own MDIO
bus, if no phy-handle and no fixed-link nodes were present.
The -ENODEV error code from the first attempt (phylink_of_phy_connect)
is what triggers the second attempt (phylink_connect_phy).
However, when the first attempt returns a different error code than
-ENODEV, this results in an unbalance of calls to phylink_create and
phylink_destroy by the time we exit the function. The phylink instance
has leaked.
There are many other error codes that can be returned by
phylink_of_phy_connect. For example, phylink_validate returns -EINVAL.
So this is a practical issue too.
Fixes: aab9c4067d ("net: dsa: Plug in PHYLINK support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20210914134331.2303380-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04f08eb44b upstream.
syzbot reported another data-race in af_unix [1]
Lets change __skb_insert() to use WRITE_ONCE() when changing
skb head qlen.
Also, change unix_dgram_poll() to use lockless version
of unix_recvq_full()
It is verry possible we can switch all/most unix_recvq_full()
to the lockless version, this will be done in a future kernel version.
[1] HEAD commit: 8596e589b7
BUG: KCSAN: data-race in skb_queue_tail / unix_dgram_poll
write to 0xffff88814eeb24e0 of 4 bytes by task 25815 on cpu 0:
__skb_insert include/linux/skbuff.h:1938 [inline]
__skb_queue_before include/linux/skbuff.h:2043 [inline]
__skb_queue_tail include/linux/skbuff.h:2076 [inline]
skb_queue_tail+0x80/0xa0 net/core/skbuff.c:3264
unix_dgram_sendmsg+0xff2/0x1600 net/unix/af_unix.c:1850
sock_sendmsg_nosec net/socket.c:703 [inline]
sock_sendmsg net/socket.c:723 [inline]
____sys_sendmsg+0x360/0x4d0 net/socket.c:2392
___sys_sendmsg net/socket.c:2446 [inline]
__sys_sendmmsg+0x315/0x4b0 net/socket.c:2532
__do_sys_sendmmsg net/socket.c:2561 [inline]
__se_sys_sendmmsg net/socket.c:2558 [inline]
__x64_sys_sendmmsg+0x53/0x60 net/socket.c:2558
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffff88814eeb24e0 of 4 bytes by task 25834 on cpu 1:
skb_queue_len include/linux/skbuff.h:1869 [inline]
unix_recvq_full net/unix/af_unix.c:194 [inline]
unix_dgram_poll+0x2bc/0x3e0 net/unix/af_unix.c:2777
sock_poll+0x23e/0x260 net/socket.c:1288
vfs_poll include/linux/poll.h:90 [inline]
ep_item_poll fs/eventpoll.c:846 [inline]
ep_send_events fs/eventpoll.c:1683 [inline]
ep_poll fs/eventpoll.c:1798 [inline]
do_epoll_wait+0x6ad/0xf00 fs/eventpoll.c:2226
__do_sys_epoll_wait fs/eventpoll.c:2238 [inline]
__se_sys_epoll_wait fs/eventpoll.c:2233 [inline]
__x64_sys_epoll_wait+0xf6/0x120 fs/eventpoll.c:2233
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0x0000001b -> 0x00000001
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 25834 Comm: syz-executor.1 Tainted: G W 5.14.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 86b18aaa2b ("skbuff: fix a data race in skb_queue_len()")
Cc: Qian Cai <cai@lca.pw>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c4cea8fa7 upstream.
If the sendmsg() call in vhost_tx_batch() fails, both the 'batched_xdp'
and 'done_idx' indexes are left unchanged. If such failure happens
when batched_xdp == VHOST_NET_BATCH, the next call to
vhost_net_build_xdp() will access and write memory outside the xdp
buffers area.
Since sendmsg() can only error with EBADFD, this change addresses the
issue explicitly freeing the XDP buffers batch on error.
Fixes: 0a0be13b8f ("vhost_net: batch submitting XDP buffers to underlayer sockets")
Suggested-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec783c7cb2 upstream.
We need to import the 'sys' package since the script has called
sys.exit() method.
Fixes: 6ad7cbc015 ("Makefile: Add clang-tidy and static analyzer support to makefile")
Signed-off-by: Kortan <kortanzh@gmail.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5c102238c upstream.
There is an off-by-one problem in ipa_table_init_add(), when
initializing filter tables.
In that function, the number of filter table entries is determined
based on the number of set bits in the filter map. However that
count does *not* include the extra "slot" in the filter table that
holds the filter map itself. Meanwhile, ipa_table_addr() *does*
include the filter map in the memory it returns, but because the
count it's provided doesn't include it, it includes one too few
table entries.
Fix this by including the extra slot for the filter map in the count
computed in ipa_table_init_add().
Note: ipa_filter_reset_table() does not have this problem; it resets
filter table entries one by one, but does not overwrite the filter
bitmap.
Fixes: 2b9feef2b6 ("soc: qcom: ipa: filter and routing tables")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b89a05b21f upstream.
In perf_event_addr_filters_apply, the task associated with
the event (event->ctx->task) is read using READ_ONCE at the beginning
of the function, checked, and then re-read from event->ctx->task,
voiding all guarantees of the checks. Reuse the value that was read by
READ_ONCE to ensure the consistency of the task struct throughout the
function.
Fixes: 375637bc52 ("perf/core: Introduce address range filtering")
Signed-off-by: Baptiste Lepers <baptiste.lepers@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20210906015310.12802-1-baptiste.lepers@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70f437fb43 upstream.
Dispatching requests inline with the .queue_rq() call may block while
holding the send_mutex. If the tcp io_work also happens to schedule, it
may see the req_list is non-empty, leaving "pending" true and remaining
in TASK_RUNNING. Since io_work is of higher scheduling priority, the
.queue_rq task may not get a chance to run, blocking forward progress
and leading to io timeouts.
Instead of checking for pending requests within io_work, let the queueing
restart io_work outside the send_mutex lock if there is more work to be
done.
Fixes: a0fdd14180 ("nvme-tcp: rerun io_work if req_list is not empty")
Reported-by: Samuel Jones <sjones@kalrayinc.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee27e330a9 upstream.
Fixes the below flow of sleeping in atomic context by releasing
the RCU lock before calling to free_match_list.
build_match_list() <- disables preempt
-> free_match_list()
-> tree_put_node()
-> down_write_ref_node() <- take write lock
Fixes: 693c6883bb ("net/mlx5: Add hash table for flow groups in flow table")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 57f0ff059e upstream.
It's later supposed to be either a correct address or NULL. Without the
initialization, it may contain an undefined value which results in the
following segmentation fault:
# perf top --sort comm -g --ignore-callees=do_idle
terminates with:
#0 0x00007ffff56b7685 in __strlen_avx2 () from /lib64/libc.so.6
#1 0x00007ffff55e3802 in strdup () from /lib64/libc.so.6
#2 0x00005555558cb139 in hist_entry__init (callchain_size=<optimized out>, sample_self=true, template=0x7fffde7fb110, he=0x7fffd801c250) at util/hist.c:489
#3 hist_entry__new (template=template@entry=0x7fffde7fb110, sample_self=sample_self@entry=true) at util/hist.c:564
#4 0x00005555558cb4ba in hists__findnew_entry (hists=hists@entry=0x5555561d9e38, entry=entry@entry=0x7fffde7fb110, al=al@entry=0x7fffde7fb420,
sample_self=sample_self@entry=true) at util/hist.c:657
#5 0x00005555558cba1b in __hists__add_entry (hists=hists@entry=0x5555561d9e38, al=0x7fffde7fb420, sym_parent=<optimized out>, bi=bi@entry=0x0, mi=mi@entry=0x0,
sample=sample@entry=0x7fffde7fb4b0, sample_self=true, ops=0x0, block_info=0x0) at util/hist.c:288
#6 0x00005555558cbb70 in hists__add_entry (sample_self=true, sample=0x7fffde7fb4b0, mi=0x0, bi=0x0, sym_parent=<optimized out>, al=<optimized out>, hists=0x5555561d9e38)
at util/hist.c:1056
#7 iter_add_single_cumulative_entry (iter=0x7fffde7fb460, al=<optimized out>) at util/hist.c:1056
#8 0x00005555558cc8a4 in hist_entry_iter__add (iter=iter@entry=0x7fffde7fb460, al=al@entry=0x7fffde7fb420, max_stack_depth=<optimized out>, arg=arg@entry=0x7fffffff7db0)
at util/hist.c:1231
#9 0x00005555557cdc9a in perf_event__process_sample (machine=<optimized out>, sample=0x7fffde7fb4b0, evsel=<optimized out>, event=<optimized out>, tool=0x7fffffff7db0)
at builtin-top.c:842
#10 deliver_event (qe=<optimized out>, qevent=<optimized out>) at builtin-top.c:1202
#11 0x00005555558a9318 in do_flush (show_progress=false, oe=0x7fffffff80e0) at util/ordered-events.c:244
#12 __ordered_events__flush (oe=oe@entry=0x7fffffff80e0, how=how@entry=OE_FLUSH__TOP, timestamp=timestamp@entry=0) at util/ordered-events.c:323
#13 0x00005555558a9789 in __ordered_events__flush (timestamp=<optimized out>, how=<optimized out>, oe=<optimized out>) at util/ordered-events.c:339
#14 ordered_events__flush (how=OE_FLUSH__TOP, oe=0x7fffffff80e0) at util/ordered-events.c:341
#15 ordered_events__flush (oe=oe@entry=0x7fffffff80e0, how=how@entry=OE_FLUSH__TOP) at util/ordered-events.c:339
#16 0x00005555557cd631 in process_thread (arg=0x7fffffff7db0) at builtin-top.c:1114
#17 0x00007ffff7bb817a in start_thread () from /lib64/libpthread.so.0
#18 0x00007ffff5656dc3 in clone () from /lib64/libc.so.6
If you look at the frame #2, the code is:
488 if (he->srcline) {
489 he->srcline = strdup(he->srcline);
490 if (he->srcline == NULL)
491 goto err_rawdata;
492 }
If he->srcline is not NULL (it is not NULL if it is uninitialized rubbish),
it gets strdupped and strdupping a rubbish random string causes the problem.
Also, if you look at the commit 1fb7d06a50, it adds the srcline property
into the struct, but not initializing it everywhere needed.
Committer notes:
Now I see, when using --ignore-callees=do_idle we end up here at line
2189 in add_callchain_ip():
2181 if (al.sym != NULL) {
2182 if (perf_hpp_list.parent && !*parent &&
2183 symbol__match_regex(al.sym, &parent_regex))
2184 *parent = al.sym;
2185 else if (have_ignore_callees && root_al &&
2186 symbol__match_regex(al.sym, &ignore_callees_regex)) {
2187 /* Treat this symbol as the root,
2188 forgetting its callees. */
2189 *root_al = al;
2190 callchain_cursor_reset(cursor);
2191 }
2192 }
And the al that doesn't have the ->srcline field initialized will be
copied to the root_al, so then, back to:
1211 int hist_entry_iter__add(struct hist_entry_iter *iter, struct addr_location *al,
1212 int max_stack_depth, void *arg)
1213 {
1214 int err, err2;
1215 struct map *alm = NULL;
1216
1217 if (al)
1218 alm = map__get(al->map);
1219
1220 err = sample__resolve_callchain(iter->sample, &callchain_cursor, &iter->parent,
1221 iter->evsel, al, max_stack_depth);
1222 if (err) {
1223 map__put(alm);
1224 return err;
1225 }
1226
1227 err = iter->ops->prepare_entry(iter, al);
1228 if (err)
1229 goto out;
1230
1231 err = iter->ops->add_single_entry(iter, al);
1232 if (err)
1233 goto out;
1234
That al at line 1221 is what hist_entry_iter__add() (called from
sample__resolve_callchain()) saw as 'root_al', and then:
iter->ops->add_single_entry(iter, al);
will go on with al->srcline with a bogus value, I'll add the above
sequence to the cset and apply, thanks!
Signed-off-by: Michael Petlan <mpetlan@redhat.com>
CC: Milian Wolff <milian.wolff@kdab.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Fixes: 1fb7d06a50 ("perf report Use srcline from callchain for hist entries")
Link: https //lore.kernel.org/r/20210719145332.29747-1-mpetlan@redhat.com
Reported-by: Juri Lelli <jlelli@redhat.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 040b8907cc upstream.
With the new static annotation, the compiler warns when the functions
are actually unused:
drivers/gpu/drm/rockchip/cdn-dp-core.c:1123:12: error: 'cdn_dp_resume' defined but not used [-Werror=unused-function]
1123 | static int cdn_dp_resume(struct device *dev)
| ^~~~~~~~~~~~~
Mark them __maybe_unused to suppress that warning as well.
[ Not so 'new' static annotations any more, and I removed the part of
the patch that added __maybe_unused to cdn_dp_suspend(), because it's
used by the shutdown/remove code.
So only the resume function ends up possibly unused if CONFIG_PM isn't
set - Linus ]
Fixes: 7c49abb4c2 ("drm/rockchip: cdn-dp-core: Make cdn_dp_core_suspend/resume static")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f4bb62e64c upstream.
In tipc_sk_enqueue() we use hardcoded 2 jiffies to extract
socket buffer from generic queue to particular socket.
The 2 jiffies is too short in case there are other high priority
tasks get CPU cycles for multiple jiffies update. As result, no
buffer could be enqueued to particular socket.
To solve this, we switch to use constant timeout 20msecs.
Then, the function will be expired between 2 jiffies (CONFIG_100HZ)
and 20 jiffies (CONFIG_1000HZ).
Fixes: c637c10355 ("tipc: resolve race problem at unicast message reception")
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e3f0cc1a94 upstream.
A number of users have reported that they were not able to get the PHY
to successfully link up, especially after commit c36757eb9d ("net:
phy: consider AN_RESTART status when reading link status") where we
stopped reading just BMSR, but we also read BMCR to determine the link
status.
Andrius at NetBSD did a wonderful job at debugging the problem
and found out that the MDIO bus clock frequency would be incorrectly set
back to its default value which would prevent the MDIO bus controller
from reading PHY registers properly. Back when we only read BMSR, if we
read all 1s, we could falsely indicate a link status, though in general
there is a cable plugged in, so this went unnoticed. After a second read
of BMCR was added, a wrong read will lead to the inability to determine
a link UP condition which is when it started to be visibly broken, even
if it was long before that.
The fix consists in restoring the value of the MD_CSR register that was
set prior to the MAC reset.
Link: http://gnats.netbsd.org/cgi-bin/query-pr-single.pl?number=53494
Fixes: 90f750a81a ("r6040: consolidate MAC reset to its own function")
Reported-by: Andrius V <vezhlys@gmail.com>
Reported-by: Darek Strugacz <darek.strugacz@op.pl>
Tested-by: Darek Strugacz <darek.strugacz@op.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b6ff7eb66 upstream.
The reference count leak issue may take place in an error handling
path. If both conditions of tunnel->version == L2TP_HDR_VER_3 and the
return value of l2tp_v3_ensure_opt_in_linear is nonzero, the function
would directly jump to label invalid, without decrementing the reference
count of the l2tp_session object session increased earlier by
l2tp_tunnel_get_session(). This may result in refcount leaks.
Fix this issue by decrease the reference count before jumping to the
label invalid.
Fixes: 4522a70db7 ("l2tp: fix reading optional fields of L2TPv3")
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9ea761fdd upstream.
Commit 2677d20677 ("dccp: don't free ccid2_hc_tx_sock ...") fixed
a UAF but reintroduced CVE-2017-6074.
When the sock is cloned, two dccps_hc_tx_ccid will reference to the
same ccid. So one can free the ccid object twice from two socks after
cloning.
This issue was found by "Hadar Manor" as well and assigned with
CVE-2020-16119, which was fixed in Ubuntu's kernel. So here I port
the patch from Ubuntu to fix it.
The patch prevents cloned socks from referencing the same ccid.
Fixes: 2677d20677 ("dccp: don't free ccid2_hc_tx_sock ...")
Signed-off-by: Zhenpeng Lin <zplin@psu.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7366c23ff4 upstream.
Building dp83640.c on arch/parisc/ produces a build warning for
PAGE0 being redefined. Since the macro is not used in the dp83640
driver, just make it a comment for documentation purposes.
In file included from ../drivers/net/phy/dp83640.c:23:
../drivers/net/phy/dp83640_reg.h:8: warning: "PAGE0" redefined
8 | #define PAGE0 0x0000
from ../drivers/net/phy/dp83640.c:11:
../arch/parisc/include/asm/page.h:187: note: this is the location of the previous definition
187 | #define PAGE0 ((struct zeropage *)__PAGE_OFFSET)
Fixes: cb646e2b02 ("ptp: Added a clock driver for the National Semiconductor PHYTER.")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Richard Cochran <richard.cochran@omicron.at>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210913220605.19682-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c3a0a018e upstream.
Remove the assert from the callback priv lookup function since it does
not require RTNL lock and is already protected by flow_indr_block_lock.
This will avoid warnings from being emitted to dmesg if the driver
registers its callback after an ingress qdisc was created for a
netdevice.
The warnings started after the following patch was merged:
commit 74fc4f8287 ("net: Fix offloading indirect devices dependency on qdisc order creation")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc19862ffe upstream.
syzbot reported an use-after-free crash:
BUG: KASAN: use-after-free in tipc_recvmsg+0xf77/0xf90 net/tipc/socket.c:1979
Call Trace:
tipc_recvmsg+0xf77/0xf90 net/tipc/socket.c:1979
sock_recvmsg_nosec net/socket.c:943 [inline]
sock_recvmsg net/socket.c:961 [inline]
sock_recvmsg+0xca/0x110 net/socket.c:957
tipc_conn_rcv_from_sock+0x162/0x2f0 net/tipc/topsrv.c:398
tipc_conn_recv_work+0xeb/0x190 net/tipc/topsrv.c:421
process_one_work+0x98d/0x1630 kernel/workqueue.c:2276
worker_thread+0x658/0x11f0 kernel/workqueue.c:2422
As Hoang pointed out, it was caused by skb_cb->bytes_read still accessed
after calling tsk_advance_rx_queue() to free the skb in tipc_recvmsg().
This patch is to fix it by accessing skb_cb->bytes_read earlier than
calling tsk_advance_rx_queue().
Fixes: f4919ff59c ("tipc: keep the skb in rcv queue until the whole data is read")
Reported-by: syzbot+e6741b97d5552f97c24d@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 34b1999da9 upstream.
Jiri Olsa reported a fault when running:
# cat /proc/kallsyms | grep ksys_read
ffffffff8136d580 T ksys_read
# objdump -d --start-address=0xffffffff8136d580 --stop-address=0xffffffff8136d590 /proc/kcore
/proc/kcore: file format elf64-x86-64
Segmentation fault
general protection fault, probably for non-canonical address 0xf887ffcbff000: 0000 [#1] SMP PTI
CPU: 12 PID: 1079 Comm: objdump Not tainted 5.14.0-rc5qemu+ #508
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-4.fc34 04/01/2014
RIP: 0010:kern_addr_valid
Call Trace:
read_kcore
? rcu_read_lock_sched_held
? rcu_read_lock_sched_held
? rcu_read_lock_sched_held
? trace_hardirqs_on
? rcu_read_lock_sched_held
? lock_acquire
? lock_acquire
? rcu_read_lock_sched_held
? lock_acquire
? rcu_read_lock_sched_held
? rcu_read_lock_sched_held
? rcu_read_lock_sched_held
? lock_release
? _raw_spin_unlock
? __handle_mm_fault
? rcu_read_lock_sched_held
? lock_acquire
? rcu_read_lock_sched_held
? lock_release
proc_reg_read
? vfs_read
vfs_read
ksys_read
do_syscall_64
entry_SYSCALL_64_after_hwframe
The fault happens because kern_addr_valid() dereferences existent but not
present PMD in the high kernel mappings.
Such PMDs are created when free_kernel_image_pages() frees regions larger
than 2Mb. In this case, a part of the freed memory is mapped with PMDs and
the set_memory_np_noalias() -> ... -> __change_page_attr() sequence will
mark the PMD as not present rather than wipe it completely.
Have kern_addr_valid() check whether higher level page table entries are
present before trying to dereference them to fix this issue and to avoid
similar issues in the future.
Stable backporting note:
------------------------
Note that the stable marking is for all active stable branches because
there could be cases where pagetable entries exist but are not valid -
see 9a14aefc1d ("x86: cpa, fix lookup_address"), for example. So make
sure to be on the safe side here and use pXY_present() accessors rather
than pXY_none() which could #GP when accessing pages in the direct map.
Also see:
c40a56a781 ("x86/mm/init: Remove freed kernel image areas from alias mapping")
for more info.
Reported-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: Dave Hansen <dave.hansen@intel.com>
Tested-by: Jiri Olsa <jolsa@redhat.com>
Cc: <stable@vger.kernel.org> # 4.4+
Link: https://lkml.kernel.org/r/20210819132717.19358-1-rppt@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aeef8b5089 upstream.
The end address passed to memtype_reserve() is handed directly to
sanitize_phys(). However, end is exclusive and sanitize_phys() expects
an inclusive address. If end falls at the end of the physical address
space, sanitize_phys() will return 0. This can result in drivers
failing to load, and the following warning:
WARNING: CPU: 26 PID: 749 at arch/x86/mm/pat.c:354 reserve_memtype+0x262/0x450
reserve_memtype failed: [mem 0x3ffffff00000-0xffffffffffffffff], req uncached-minus
Call Trace:
[<ffffffffa427b1f2>] reserve_memtype+0x262/0x450
[<ffffffffa42764aa>] ioremap_nocache+0x1a/0x20
[<ffffffffc04620a1>] mpt3sas_base_map_resources+0x151/0xa60 [mpt3sas]
[<ffffffffc0465555>] mpt3sas_base_attach+0xf5/0xa50 [mpt3sas]
---[ end trace 6d6eea4438db89ef ]---
ioremap reserve_memtype failed -22
mpt3sas_cm0: unable to map adapter memory! or resource not found
mpt3sas_cm0: failure at drivers/scsi/mpt3sas/mpt3sas_scsih.c:10597/_scsih_probe()!
Fix this by passing the inclusive end address to sanitize_phys().
Fixes: 510ee090ab ("x86/mm/pat: Prepare {reserve, free}_memtype() for "decoy" addresses")
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/x49o8a3pu5i.fsf@segfault.boston.devel.redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f2faea8b64 upstream.
When we forcefully evict a mapping from the the address space and thus the
MMU context, the MMU context is leaked, as the mapping no longer points to
it, so it doesn't get freed when the GEM object is destroyed. Add the
mssing context put to fix the leak.
Cc: stable@vger.kernel.org # 5.4
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d6408538f0 upstream.
Move the refcount manipulation of the MMU context to the point where the
hardware state is programmed. At that point it is also known if a previous
MMU state is still there, or the state needs to be reprogrammed with a
potentially different context.
Cc: stable@vger.kernel.org # 5.4
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f3eea9d01 upstream.
The MMU state may be kept across a runtime suspend/resume cycle, as we
avoid a full hardware reset to keep the latency of the runtime PM small.
Don't pretend that the MMU state is lost in driver state. The MMU
context is pushed out when new HW jobs with a different context are
coming in. The only exception to this is when the GPU is unbound, in
which case we need to make sure to also free the last active context.
Cc: stable@vger.kernel.org # 5.4
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23e0f5a57d upstream.
While the DMA frontend can only be active when the MMU context is set, the
reverse isn't necessarily true, as the frontend can be stopped while the
MMU state is kept. Stop treating mmu_context being set as a indication that
the frontend is running and instead add a explicit property.
Cc: stable@vger.kernel.org # 5.4
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cda7532916 upstream.
The prev context is the MMU context at the time of the job
queueing in hardware. As a job might be queued multiple times
due to recovery after a GPU hang, we need to make sure to put
the stale prev MMU context from a prior queuing, to avoid the
reference and thus the MMU context leaking.
Cc: stable@vger.kernel.org # 5.4
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e35ac9d0b5 upstream.
When we need a buffer for SVE register state we call sve_alloc() to make
sure that one is there. In order to avoid repeated allocations and frees
we keep the buffer around unless we change vector length and just memset()
it to ensure a clean register state. The function that deals with this
takes the task to operate on as an argument, however in the case where we
do a memset() we initialise using the SVE state size for the current task
rather than the task passed as an argument.
This is only an issue in the case where we are setting the register state
for a task via ptrace and the task being configured has a different vector
length to the task tracing it. In the case where the buffer is larger in
the traced process we will leak old state from the traced process to
itself, in the case where the buffer is smaller in the traced process we
will overflow the buffer and corrupt memory.
Fixes: bc0ee47603 ("arm64/sve: Core task context handling")
Cc: <stable@vger.kernel.org> # 4.15.x
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210909165356.10675-1-broonie@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 16c8d2df7e upstream.
When setting up the next segment, we check what type the iter is and
handle it accordingly. However, when incrementing and processed amount
we do not, and both iter advance and addr/len are adjusted, regardless
of type. Split the increment side just like we do on the setup side.
Fixes: 4017eb91a9 ("io_uring: make loop_rw_iter() use original user supplied pointers")
Cc: stable@vger.kernel.org
Reported-by: Valentina Palmiotti <vpalmiotti@gmail.com>
Reviewed-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f93e834fa upstream.
The mount option max_inline ranges from 0 to the sectorsize (which is
now equal to page size). But we parse the mount options too early and
before the actual sectorsize is read from the superblock. So the upper
limit of max_inline is unaware of the actual sectorsize and is limited
by the temporary sectorsize 4096, even on a system where the default
sectorsize is 64K.
Fix this by reading the superblock sectorsize before the mount option
parse.
Reported-by: Alexander Tsvetkov <alexander.tsvetkov@oracle.com>
CC: stable@vger.kernel.org # 5.4+
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5fab34565 upstream.
In lock_region, simplify the calculation of the region_width parameter.
This field is the size, but encoded as ceil(log2(size)) - 1.
ceil(log2(size)) may be computed directly as fls(size - 1). However, we
want to use the 64-bit versions as the amount to lock can exceed
32-bits.
This avoids undefined (and completely wrong) behaviour when locking all
memory (size ~0). In this case, the old code would "round up" ~0 to the
nearest page, overflowing to 0. Since fls(0) == 0, this would calculate
a region width of 10 + 0 = 10. But then the code would shift by
(region_width - 11) = -1. As shifting by a negative number is undefined,
UBSAN flags the bug. Of course, even if it were defined the behaviour is
wrong, instead of locking all memory almost none would get locked.
The new form of the calculation corrects this special case and avoids
the undefined behaviour.
Signed-off-by: Alyssa Rosenzweig <alyssa.rosenzweig@collabora.com>
Reported-and-tested-by: Chris Morgan <macromorgan@hotmail.com>
Fixes: f3ba91228e ("drm/panfrost: Add initial panfrost driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Steven Price <steven.price@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210824173028.7528-2-alyssa.rosenzweig@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92bd92c44d upstream.
Commit 2f015ec6ea ("drm/dp_mst: Add sideband down request tracing +
selftests") added some debug code for sideband message tracing. But
it seems to have unintentionally changed the behavior on sideband message
failure. It catches and returns failure only if DRM_UT_DP is enabled.
Otherwise it ignores the error code and returns success. So on an MST
unplug, the caller is unaware that the clear payload message failed and
ends up waiting for 4 seconds for the response. Fixes the issue by
returning the proper error code.
Changes in V2:
-- Revise commit text as review comment
-- add Fixes text
Changes in V3:
-- remove "unlikely" optimization
Fixes: 2f015ec6ea ("drm/dp_mst: Add sideband down request tracing + selftests")
Cc: <stable@vger.kernel.org> # v5.5+
Signed-off-by: Rajkumar Subbiah <rsubbia@codeaurora.org>
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1625585434-9562-1-git-send-email-khsieh@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 552799f8b3 upstream.
Currently, outgoing packets larger than 1496 bytes are dropped when
tagged VLAN is used on a switch port.
Add the frame check sequence length to the value of the register
GSWIP_MAC_FLEN to fix this. This matches the lantiq_ppa vendor driver,
which uses a value consisting of 1518 bytes for the MAC frame, plus the
lengths of special tag and VLAN tags.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Cc: stable@vger.kernel.org
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32b2397c1e upstream.
There is a use after free crash when the pmem driver tears down its
mapping while I/O is still inbound.
This is triggered by driver unbind, "ndctl destroy-namespace", while I/O
is in flight.
Fix the sequence of blk_cleanup_queue() vs memunmap().
The crash signature is of the form:
BUG: unable to handle page fault for address: ffffc90080200000
CPU: 36 PID: 9606 Comm: systemd-udevd
Call Trace:
? pmem_do_bvec+0xf9/0x3a0
? xas_alloc+0x55/0xd0
pmem_rw_page+0x4b/0x80
bdev_read_page+0x86/0xb0
do_mpage_readpage+0x5d4/0x7a0
? lru_cache_add+0xe/0x10
mpage_readpages+0xf9/0x1c0
? bd_link_disk_holder+0x1a0/0x1a0
blkdev_readpages+0x1d/0x20
read_pages+0x67/0x1a0
ndctl Call Trace in vmcore:
PID: 23473 TASK: ffff88c4fbbe8000 CPU: 1 COMMAND: "ndctl"
__schedule
schedule
blk_mq_freeze_queue_wait
blk_freeze_queue
blk_cleanup_queue
pmem_release_queue
devm_action_release
release_nodes
devres_release_all
device_release_driver_internal
device_driver_detach
unbind_store
Cc: <stable@vger.kernel.org>
Signed-off-by: sumiyawang <sumiyawang@tencent.com>
Reviewed-by: yongduan <yongduan@tencent.com>
Link: https://lore.kernel.org/r/1629632949-14749-1-git-send-email-sumiyawang@tencent.com
Fixes: 50f44ee724 ("mm/devm_memremap_pages: fix final page put race")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fab827dbee upstream.
Commit 5d097056c9 ("kmemcg: account certain kmem allocations to memcg")
enabled memcg accounting for pids allocated from init_pid_ns.pid_cachep,
but forgot to adjust the setting for nested pid namespaces. As a result,
pid memory is not accounted exactly where it is really needed, inside
memcg-limited containers with their own pid namespaces.
Pid was one the first kernel objects enabled for memcg accounting.
init_pid_ns.pid_cachep marked by SLAB_ACCOUNT and we can expect that any
new pids in the system are memcg-accounted.
Though recently I've noticed that it is wrong. nested pid namespaces
creates own slab caches for pid objects, nested pids have increased size
because contain id both for all parent and for own pid namespaces. The
problem is that these slab caches are _NOT_ marked by SLAB_ACCOUNT, as a
result any pids allocated in nested pid namespaces are not
memcg-accounted.
Pid struct in nested pid namespace consumes up to 500 bytes memory, 100000
such objects gives us up to ~50Mb unaccounted memory, this allow container
to exceed assigned memcg limits.
Link: https://lkml.kernel.org/r/8b6de616-fd1a-02c6-cbdb-976ecdcfa604@virtuozzo.com
Fixes: 5d097056c9 ("kmemcg: account certain kmem allocations to memcg")
Cc: stable@vger.kernel.org
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Reviewed-by: Michal Koutný <mkoutny@suse.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Acked-by: Roman Gushchin <guro@fb.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32d4f4b782 upstream.
Commit f56ce412a5 ("mm: memcontrol: fix occasional OOMs due to
proportional memory.low reclaim") introduced a divide by zero corner
case when oomd is being used in combination with cgroup memory.low
protection.
When oomd decides to kill a cgroup, it will force the cgroup memory to
be reclaimed after killing the tasks, by writing to the memory.max file
for that cgroup, forcing the remaining page cache and reclaimable slab
to be reclaimed down to zero.
Previously, on cgroups with some memory.low protection that would result
in the memory being reclaimed down to the memory.low limit, or likely
not at all, having the page cache reclaimed asynchronously later.
With f56ce412a5 the oomd write to memory.max tries to reclaim all the
way down to zero, which may race with another reclaimer, to the point of
ending up with the divide by zero below.
This patch implements the obvious fix.
Link: https://lkml.kernel.org/r/20210826220149.058089c6@imladris.surriel.com
Fixes: f56ce412a5 ("mm: memcontrol: fix occasional OOMs due to proportional memory.low reclaim")
Signed-off-by: Rik van Riel <riel@surriel.com>
Acked-by: Roman Gushchin <guro@fb.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Chris Down <chris@chrisdown.name>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09a26e8327 upstream.
Guillaume Morin reported hitting the following WARNING followed by GPF or
NULL pointer deference either in cgroups_destroy or in the kill_css path.:
percpu ref (css_release) <= 0 (-1) after switching to atomic
WARNING: CPU: 23 PID: 130 at lib/percpu-refcount.c:196 percpu_ref_switch_to_atomic_rcu+0x127/0x130
CPU: 23 PID: 130 Comm: ksoftirqd/23 Kdump: loaded Tainted: G O 5.10.60 #1
RIP: 0010:percpu_ref_switch_to_atomic_rcu+0x127/0x130
Call Trace:
rcu_core+0x30f/0x530
rcu_core_si+0xe/0x10
__do_softirq+0x103/0x2a2
run_ksoftirqd+0x2b/0x40
smpboot_thread_fn+0x11a/0x170
kthread+0x10a/0x140
ret_from_fork+0x22/0x30
Upon further examination, it was discovered that the css structure was
associated with hugetlb reservations.
For private hugetlb mappings the vma points to a reserve map that
contains a pointer to the css. At mmap time, reservations are set up
and a reference to the css is taken. This reference is dropped in the
vma close operation; hugetlb_vm_op_close. However, if a vma is split no
additional reference to the css is taken yet hugetlb_vm_op_close will be
called twice for the split vma resulting in an underflow.
Fix by taking another reference in hugetlb_vm_op_open. Note that the
reference is only taken for the owner of the reserve map. In the more
common fork case, the pointer to the reserve map is cleared for
non-owning vmas.
Link: https://lkml.kernel.org/r/20210830215015.155224-1-mike.kravetz@oracle.com
Fixes: e9fe92ae0c ("hugetlb_cgroup: add reservation accounting for private mappings")
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Reported-by: Guillaume Morin <guillaume@morinfr.org>
Suggested-by: Guillaume Morin <guillaume@morinfr.org>
Tested-by: Guillaume Morin <guillaume@morinfr.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93ebb68287 upstream.
Since commit 903cd0f315 ("swiotlb: Use is_swiotlb_force_bounce for
swiotlb data bouncing") if code sets swiotlb_force it needs to do so
before the swiotlb is initialised. Otherwise
io_tlb_default_mem->force_bounce will not get set to true, and devices
that use (the default) swiotlb will not bounce despite switolb_force
having the value of SWIOTLB_FORCE.
Let us restore swiotlb functionality for PV by fulfilling this new
requirement.
This change addresses what turned out to be a fragility in
commit 64e1f0c531 ("s390/mm: force swiotlb for protected
virtualization"), which ain't exactly broken in its original context,
but could give us some more headache if people backport the broken
change and forget this fix.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Fixes: 903cd0f315 ("swiotlb: Use is_swiotlb_force_bounce for swiotlb data bouncing")
Fixes: 64e1f0c531 ("s390/mm: force swiotlb for protected virtualization")
Cc: stable@vger.kernel.org #5.3+
Signed-off-by: Konrad Rzeszutek Wilk <konrad@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f34ee9cb2c upstream.
In the numa=off kernel command-line configuration init_chip_info() loops
around the number of chips and attempts to copy the cpumask of that node
which is NULL for all iterations after the first chip.
Hence, store the cpu mask for each chip instead of derving cpumask from
node while populating the "chips" struct array and copy that to the
chips[i].mask
Fixes: 053819e0bf ("cpufreq: powernv: Handle throttling due to Pmax capping at chip level")
Cc: stable@vger.kernel.org # v4.3+
Reported-by: Shirisha Ganta <shirisha.ganta1@ibm.com>
Signed-off-by: Pratik R. Sampat <psampat@linux.ibm.com>
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
[mpe: Rename goto label to out_free_chip_cpu_mask]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210728120500.87549-2-psampat@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 030f653078 upstream.
I was debugging some crashes on parisc and I found out that there is a
crash possibility if a function using alloca is interrupted by a signal.
The reason for the crash is that the gcc alloca implementation leaves
garbage in the upper 32 bits of the sp register. This normally doesn't
matter (the upper bits are ignored because the PSW W-bit is clear),
however the signal delivery routine in the kernel uses full 64 bits of sp
and it fails with -EFAULT if the upper 32 bits are not zero.
I created this program that demonstrates the problem:
#include <stdlib.h>
#include <unistd.h>
#include <signal.h>
#include <alloca.h>
static __attribute__((noinline,noclone)) void aa(int *size)
{
void * volatile p = alloca(-*size);
while (1) ;
}
static void handler(int sig)
{
write(1, "signal delivered\n", 17);
_exit(0);
}
int main(void)
{
int size = -0x100;
signal(SIGALRM, handler);
alarm(1);
aa(&size);
}
If you compile it with optimizations, it will crash.
The "aa" function has this disassembly:
000106a0 <aa>:
106a0: 08 03 02 41 copy r3,r1
106a4: 08 1e 02 43 copy sp,r3
106a8: 6f c1 00 80 stw,ma r1,40(sp)
106ac: 37 dc 3f c1 ldo -20(sp),ret0
106b0: 0c 7c 12 90 stw ret0,8(r3)
106b4: 0f 40 10 9c ldw 0(r26),ret0 ; ret0 = 0x00000000FFFFFF00
106b8: 97 9c 00 7e subi 3f,ret0,ret0 ; ret0 = 0xFFFFFFFF0000013F
106bc: d7 80 1c 1a depwi 0,31,6,ret0 ; ret0 = 0xFFFFFFFF00000100
106c0: 0b 9e 0a 1e add,l sp,ret0,sp ; sp = 0xFFFFFFFFxxxxxxxx
106c4: e8 1f 1f f7 b,l,n 106c4 <aa+0x24>,r0
This patch fixes the bug by truncating the "usp" variable to 32 bits.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 632546c4b5 ]
io_size and iov_count in io_read() and io_write() hold the same value,
kill the last one.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e79c0e324b ]
abs() returns signed long, which could not convert the type
as unsigned, and it may cause a mismatch type warning from
static tools. To fix it, this patch uses an variable to save
the abs()'s result and does a explicit conversion.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a39ff4a47f ]
It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 733c99ee8b ]
In netlbl_cipsov4_add_std() when 'doi_def->map.std' alloc
failed, we sometime observe panic:
BUG: kernel NULL pointer dereference, address:
...
RIP: 0010:cipso_v4_doi_free+0x3a/0x80
...
Call Trace:
netlbl_cipsov4_add_std+0xf4/0x8c0
netlbl_cipsov4_add+0x13f/0x1b0
genl_family_rcv_msg_doit.isra.15+0x132/0x170
genl_rcv_msg+0x125/0x240
This is because in cipso_v4_doi_free() there is no check
on 'doi_def->map.std' when 'doi_def->type' equal 1, which
is possibe, since netlbl_cipsov4_add_std() haven't initialize
it before alloc 'doi_def->map.std'.
This patch just add the check to prevent panic happen for similar
cases.
Reported-by: Abaci <abaci@linux.alibaba.com>
Signed-off-by: Michael Wang <yun.wang@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c48662b9d ]
The problem is that gpio_free() can sleep and the cfg_soc() can be
called with spinlocks held. One problematic call tree is:
--> ath_reset_internal() takes &sc->sc_pcu_lock spin lock
--> ath9k_hw_reset()
--> ath9k_hw_gpio_request_in()
--> ath9k_hw_gpio_request()
--> ath9k_hw_gpio_cfg_soc()
Remove gpio_free(), use error message instead, so we should make sure
there is no GPIO conflict.
Also remove ath9k_hw_gpio_free() from ath9k_hw_apply_gpio_override(),
as gpio_mask will never be set for SOC chips.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1628481916-15030-1-git-send-email-miaoqing@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23151b9ae7 ]
Bad header can have large length field which can cause OOB.
cptr is the last bytes for read, and the eeprom is parsed
from high to low address. The OOB, triggered by the condition
length > cptr could cause memory error with a read on
negative index.
There are some sanity check around length, but it is not
compared with cptr (the remaining bytes). Here, the
corrupted/bad EEPROM can cause panic.
I was able to reproduce the crash, but I cannot find the
log and the reproducer now. After I applied the patch, the
bug is no longer reproducible.
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YM3xKsQJ0Hw2hjrc@Zekuns-MBP-16.fios-router.home
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0be883a0d7 ]
The check for count appears to be incorrect since a non-zero count
check occurs a couple of statements earlier. Currently the check is
always false and the dev->port->irq != PARPORT_IRQ_NONE part of the
check is never tested and the if statement is dead-code. Fix this
by removing the check on count.
Note that this code is pre-git history, so I can't find a sha for
it.
Acked-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Logically dead code")
Link: https://lore.kernel.org/r/20210730100710.27405-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec449ed823 ]
Under high stress, SW steering might get stuck on polling for completion
that never comes.
For such cases QP needs to have protocol retransmission mechanism enabled.
Currently the retransmission timeout is defined as 0 (unlimited). Fix this
by defining a real timeout.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6cc64770fb ]
In line 849 (#1), "mlx5dr_htbl_put(cur_htbl);" drops the reference to
cur_htbl and may cause cur_htbl to be freed.
However, cur_htbl is subsequently used in the next line, which may result
in an use-after-free bug.
Fix this by calling mlx5dr_err() before the cur_htbl is put.
Signed-off-by: Wentao_Liang <Wentao_Liang_g@163.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c6ce1c74ef ]
When TVQM is enabled (iwl_mvm_has_new_tx_api() is true), then
queue numbers are just sequentially assigned 0, 1, 2, ...
Prior to TVQM, in DQA, there were some statically allocated
queue numbers:
* IWL_MVM_DQA_AUX_QUEUE == 1,
* both IWL_MVM_DQA_INJECT_MONITOR_QUEUE and
IWL_MVM_DQA_P2P_DEVICE_QUEUE == 2, and
* IWL_MVM_DQA_AP_PROBE_RESP_QUEUE == 9.
Now, these values are assigned to the members mvm->aux_queue,
mvm->snif_queue, mvm->probe_queue and mvm->p2p_dev_queue by
default. Normally, this doesn't really matter, and if TVQM is
in fact available we override them to the real values after
allocating a queue for use there.
However, this allocation doesn't always happen. For example,
for mvm->p2p_dev_queue (== 2) it only happens when the P2P
Device interface is started, if any. If it's not started, the
value in mvm->p2p_dev_queue remains 2. This wouldn't really
matter all that much if it weren't for iwl_mvm_is_static_queue()
which checks a queue number against one of those four static
numbers.
Now, if no P2P Device or monitor interface is added then queue
2 may be dynamically allocated, yet alias mvm->p2p_dev_queue or
mvm->snif_queue, and thus iwl_mvm_is_static_queue() erroneously
returns true for it. If it then gets full, all interface queues
are stopped, instead of just backpressuring against the one TXQ
that's really the only affected one.
This clearly can lead to issues, as everything is stopped even
if just a single TXQ filled its corresponding HW queue, if it
happens to have an appropriate number (2 or 9, AUX is always
reassigned.) Due to a mac80211 bug, this also led to a situation
in which the queues remained stopped across a deauthentication
and then attempts to connect to a new AP started failing, but
that's fixed separately.
Fix all of this by simply initializing the queue numbers to
the invalid value until they're used, if TVQM is enabled, and
also setting them back to that value when the queues are later
freed again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802172232.2e47e623f9e2.I9b0830dafbb68ef35b7b8f0f46160abec02ac7d0@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ec06c2dee ]
On systems with multiple SH per SE compute_static_thread_mgmt_se#
is split into independent masks, one for each SH, in the upper and
lower 16 bits. We need to detect this and apply cu masking to each
SH. The cu mask bits are assigned first to each SE, then to
alternate SHs, then finally to higher CU id. This ensures that
the maximum number of SPIs are engaged as early as possible while
balancing CU assignment to each SH.
v2: Use max SH/SE rather than max SH in cu_per_sh.
v3: Fix comment blocks, ensure se_mask is initially zero filled,
and correctly assign se.sh.cu positions to unset bits in cu_mask.
Signed-off-by: Sean Keely <Sean.Keely@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66cce9e73e ]
When a remote usb device is attached to the local Virtual USB
Host Controller Root Hub port, the bound device driver may send
a port reset command.
vhci_hcd accepts port resets only when the device doesn't have
port address assigned to it. When reset happens device is in
assigned/used state and vhci_hcd rejects it leaving the port in
a stuck state.
This problem was found when a blue-tooth or xbox wireless dongle
was passed through using usbip.
A few drivers reset the port during probe including mt76 driver
specific to this bug report. Fix the problem with a change to
honor reset requests when device is in used state (VDEV_ST_USED).
Reported-and-tested-by: Michael <msbroadf@gmail.com>
Suggested-by: Michael <msbroadf@gmail.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210819225937.41037-1-skhan@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c75bde329 ]
If IRQ occurs between calling dsps_setup_optional_vbus_irq()
and dsps_create_musb_pdev(), then null pointer dereference occurs
since glue->musb wasn't initialized yet.
The patch puts initializing of neccesery data before registration
of the interrupt handler.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Link: https://lore.kernel.org/r/20210819163323.17714-1-lutovinova@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2847c46c61 ]
This reverts commit 5d5323a6f3.
That commit effectively disabled Intel host initiated U1/U2 lpm for devices
with periodic endpoints.
Before that commit we disabled host initiated U1/U2 lpm if the exit latency
was larger than any periodic endpoint service interval, this is according
to xhci spec xhci 1.1 specification section 4.23.5.2
After that commit we incorrectly checked that service interval was smaller
than U1/U2 inactivity timeout. This is not relevant, and can't happen for
Intel hosts as previously set U1/U2 timeout = 105% * service interval.
Patch claimed it solved cases where devices can't be enumerated because of
bandwidth issues. This might be true but it's a side effect of accidentally
turning off lpm.
exit latency calculations have been revised since then
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210820123503.2605901-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d72c74197b ]
smb_buf is allocated by small_smb_init_no_tc(), and buf type is
CIFS_SMALL_BUFFER, so we should use cifs_small_buf_release() to
release it in failed path.
Signed-off-by: Ding Hui <dinghui@sangfor.com.cn>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e72a55f2e5 ]
When a read/write command is sent via ioctl to the kernel,
and the command fails, the actual error response of the emmc
is not sent to the user.
IOCTL read/write tests are carried out using commands
17 (Single BLock Read), 24 (Single Block Write),
18 (Multi Block Read), 25 (Multi Block Write)
The tests are carried out on a 64Gb emmc device. All of these
tests try to access an "out of range" sector address (0x09B2FFFF).
It is seen that without the patch the response received by the user
is not OUT_OF_RANGE error (R1 response 31st bit is not set) as per
JEDEC specification. After applying the patch proper response is seen.
This is because the function returns without copying the response to
the user in case of failure. This patch fixes the issue.
Hence, this memcpy is required whether we get an error response or not.
Therefor it is moved up from the current position up to immediately
after we have called mmc_wait_for_req().
The test code and the output of only the CMD17 is included in the
commit to limit the message length.
CMD17 (Test Code Snippet):
==========================
printf("Forming CMD%d\n", opt_idx);
/* single block read */
cmd.blksz = 512;
cmd.blocks = 1;
cmd.write_flag = 0;
cmd.opcode = 17;
//cmd.arg = atoi(argv[3]);
cmd.arg = 0x09B2FFFF;
/* Expecting response R1B */
cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_ADTC;
memset(data, 0, sizeof(__u8) * 512);
mmc_ioc_cmd_set_data(cmd, data);
printf("Sending CMD%d: ARG[0x%08x]\n", opt_idx, cmd.arg);
if(ioctl(fd, MMC_IOC_CMD, &cmd))
perror("Error");
printf("\nResponse: %08x\n", cmd.response[0]);
CMD17 (Output without patch):
=============================
test@test-LIVA-Z:~$ sudo ./mmc cmd_test /dev/mmcblk0 17
Entering the do_mmc_commands:Device: /dev/mmcblk0 nargs:4
Entering the do_mmc_commands:Device: /dev/mmcblk0 options[17, 0x09B2FFF]
Forming CMD17
Sending CMD17: ARG[0x09b2ffff]
Error: Connection timed out
Response: 00000000
(Incorrect response)
CMD17 (Output with patch):
==========================
test@test-LIVA-Z:~$ sudo ./mmc cmd_test /dev/mmcblk0 17
[sudo] password for test:
Entering the do_mmc_commands:Device: /dev/mmcblk0 nargs:4
Entering the do_mmc_commands:Device: /dev/mmcblk0 options[17, 09B2FFFF]
Forming CMD17
Sending CMD17: ARG[0x09b2ffff]
Error: Connection timed out
Response: 80000900
(Correct OUT_OF_ERROR response as per JEDEC specification)
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20210824191726.8296-1-nishadkamdar@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d82d73da3 ]
0Day robot observed that it's easily timeout on a heavy load host.
-------------------
# selftests: bpf: test_maps
# Fork 1024 tasks to 'test_update_delete'
# Fork 1024 tasks to 'test_update_delete'
# Fork 100 tasks to 'test_hashmap'
# Fork 100 tasks to 'test_hashmap_percpu'
# Fork 100 tasks to 'test_hashmap_sizes'
# Fork 100 tasks to 'test_hashmap_walk'
# Fork 100 tasks to 'test_arraymap'
# Fork 100 tasks to 'test_arraymap_percpu'
# Failed sockmap unexpected timeout
not ok 3 selftests: bpf: test_maps # exit=1
# selftests: bpf: test_lru_map
# nr_cpus:8
-------------------
Since this test will be scheduled by 0Day to a random host that could have
only a few cpus(2-8), enlarge the timeout to avoid a false NG report.
In practice, i tried to pin it to only one cpu by 'taskset 0x01 ./test_maps',
and knew 10S is likely enough, but i still perfer to a larger value 30.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20210820015556.23276-2-lizhijian@cn.fujitsu.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ac5e45291 ]
For unexplained reasons, the prescaler register for this device needs to
be cleared (set to 1) while performing a data read or else the command
will hang. This does not appear to affect the real clock rate sent out
on the bus, so I assume it's purely to work around a hardware bug.
During normal operation, the prescaler is already set to 1, so nothing
needs to be done. However, in "initial mode" (which is used for sub-MHz
clock speeds, like the core sets while enumerating cards), it's set to
128 and so we need to reset it during data reads. We currently fail to
do this for long reads.
This has no functional affect on the driver's operation currently
written, as the MMC core always sets a clock above 1MHz before
attempting any long reads. However, the core could conceivably set any
clock speed at any time and the driver should still work, so I think
this fix is worthwhile.
I personally encountered this issue while performing data recovery on an
external chip. My connections had poor signal integrity, so I modified
the core code to reduce the clock speed. Without this change, I saw the
card enumerate but was unable to actually read any data.
Writes don't seem to work in the situation described above even with
this change (and even if the workaround is extended to encompass data
write commands). I was not able to find a way to get them working.
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Link: https://lore.kernel.org/r/2fef280d8409ab0100c26c6ac7050227defd098d.1627818365.git.tommyhebb@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6211e9cb2f ]
Trying to boot without SYSFS, but with OF_DYNAMIC quickly
results in a crash:
[ 0.088460] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000070
[...]
[ 0.103927] CPU: 1 PID: 1 Comm: swapper/0 Not tainted 5.14.0-rc3 #4179
[ 0.105810] Hardware name: linux,dummy-virt (DT)
[ 0.107147] pstate: 80000005 (Nzcv daif -PAN -UAO -TCO BTYPE=--)
[ 0.108876] pc : kernfs_find_and_get_ns+0x3c/0x7c
[ 0.110244] lr : kernfs_find_and_get_ns+0x3c/0x7c
[...]
[ 0.134087] Call trace:
[ 0.134800] kernfs_find_and_get_ns+0x3c/0x7c
[ 0.136054] safe_name+0x4c/0xd0
[ 0.136994] __of_attach_node_sysfs+0xf8/0x124
[ 0.138287] of_core_init+0x90/0xfc
[ 0.139296] driver_init+0x30/0x4c
[ 0.140283] kernel_init_freeable+0x160/0x1b8
[ 0.141543] kernel_init+0x30/0x140
[ 0.142561] ret_from_fork+0x10/0x18
While not having sysfs isn't a very common option these days,
it is still expected that such configuration would work.
Paper over it by bailing out from __of_attach_node_sysfs() if
CONFIG_SYSFS isn't enabled.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210820144722.169226-1-maz@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3736127a3a ]
Function btrfs_lookup_data_extent calls btrfs_search_slot to verify if
the EXTENT_ITEM exists in the extent tree. btrfs_search_slot can return
values bellow zero if an error happened.
Function replay_one_extent currently checks if the search found
something (0 returned) and increments the reference, and if not, it
seems to evaluate as 'not found'.
Fix the condition by checking if the value was bellow zero and return
early.
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Marcos Paulo de Souza <mpdesouza@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db87db65c1 ]
> Hi Arnd,
>
> First bad commit (maybe != root cause):
>
> tree: https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git master
> head: 2f73937c9aa561e2082839bc1a8efaac75d6e244
> commit: 47fd22f2b8 [4771/5318] cs89x0: rework driver configuration
> config: m68k-randconfig-c003-20210804 (attached as .config)
> compiler: m68k-linux-gcc (GCC) 10.3.0
> reproduce (this is a W=1 build):
> wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
> chmod +x ~/bin/make.cross
> # https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/commit/?id=47fd22f2b84765a2f7e3f150282497b902624547
> git remote add linux-next https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git
> git fetch --no-tags linux-next master
> git checkout 47fd22f2b8
> # save the attached .config to linux build tree
> COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-10.3.0 make.cross ARCH=m68k
>
> If you fix the issue, kindly add following tag as appropriate
> Reported-by: kernel test robot <lkp@intel.com>
>
> All errors (new ones prefixed by >>):
>
> In file included from include/linux/kernel.h:19,
> from include/linux/list.h:9,
> from include/linux/module.h:12,
> from drivers/net/ethernet/cirrus/cs89x0.c:51:
> drivers/net/ethernet/cirrus/cs89x0.c: In function 'net_open':
> drivers/net/ethernet/cirrus/cs89x0.c:897:20: error: implicit declaration of function 'isa_virt_to_bus'; did you mean 'virt_to_bus'? [-Werror=implicit-function-declaration]
> 897 | (unsigned long)isa_virt_to_bus(lp->dma_buff));
> | ^~~~~~~~~~~~~~~
> include/linux/printk.h:141:17: note: in definition of macro 'no_printk'
> 141 | printk(fmt, ##__VA_ARGS__); \
> | ^~~~~~~~~~~
> drivers/net/ethernet/cirrus/cs89x0.c:86:3: note: in expansion of macro 'pr_debug'
> 86 | pr_##level(fmt, ##__VA_ARGS__); \
> | ^~~
> drivers/net/ethernet/cirrus/cs89x0.c:894:3: note: in expansion of macro 'cs89_dbg'
> 894 | cs89_dbg(1, debug, "%s: dma %lx %lx\n",
> | ^~~~~~~~
> >> drivers/net/ethernet/cirrus/cs89x0.c:914:3: error: implicit declaration of function 'disable_dma'; did you mean 'disable_irq'? [-Werror=implicit-function-declaration]
As far as I can tell, this is a bug with the m68kmmu architecture, not
with my driver:
The CONFIG_ISA_DMA_API option is provided for coldfire, which implements it,
but dragonball also sets the option as a side-effect, without actually
implementing
the interfaces. The patch below should fix it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8fb4df1f5 ]
'bp_ena' in Aura context is NIX block index, setting it
zero will always backpressure NIX0 block, even if NIXLF
belongs to NIX1. Hence fix this by setting it appropriately
based on NIX block address.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05e4588738 ]
The kernel test robot reports undefined reference after we report wakeup
reason to mac80211. This is because CONFIG_PM is not defined in the testing
configuration file. In fact, functions within wow.c are used if CONFIG_PM
is defined, so use CONFIG_PM to decide whether we build this file or not.
The reported messages are:
hppa-linux-ld: drivers/net/wireless/realtek/rtw88/wow.o: in function `rtw_wow_show_wakeup_reason':
>> (.text+0x6c4): undefined reference to `ieee80211_report_wowlan_wakeup'
>> hppa-linux-ld: (.text+0x6e0): undefined reference to `ieee80211_report_wowlan_wakeup'
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210728014335.8785-4-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02a55c0009 ]
In current wow flow, driver calls rtw_wow_fw_start and sleep for 100ms,
to wait firmware finish preliminary work and then update the value of
WOWLAN_WAKE_REASON register to zero. But later firmware will start wow
function with power-saving mode, in which mode the value of
WOWLAN_WAKE_REASON register is 0xea. So driver may get 0xea value and
return fail. We use read_poll_timeout instead to check the value to avoid
this issue.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210728014335.8785-2-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c626f3864b ]
In certain randconfigs, clang warns:
drivers/gpu/drm/exynos/exynos_drm_dma.c:121:19: warning: variable
'mapping' is uninitialized when used here [-Wuninitialized]
priv->mapping = mapping;
^~~~~~~
drivers/gpu/drm/exynos/exynos_drm_dma.c:111:16: note: initialize the
variable 'mapping' to silence this warning
void *mapping;
^
= NULL
1 warning generated.
This occurs when CONFIG_EXYNOS_IOMMU is enabled and both
CONFIG_ARM_DMA_USE_IOMMU and CONFIG_IOMMU_DMA are disabled, which makes
the code look like
void *mapping;
if (0)
mapping = arm_iommu_create_mapping()
else if (0)
mapping = iommu_get_domain_for_dev()
...
priv->mapping = mapping;
Add an else branch that initializes mapping to the -ENODEV error pointer
so that there is no more warning and the driver does not change during
runtime.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7de875b231 ]
Locks have two sets of op arrays, fl_lmops for the lock manager (lockd
or nfsd), fl_ops for the filesystem. The server-side lockd code has
been setting its own fl_ops, which leads to confusion (and crashes) in
the reexport case, where the filesystem expects to be the only one
setting fl_ops.
And there's no reason for it that I can see-the lm_get/put_owner ops do
the same job.
Reported-by: Daire Byrne <daire@dneg.com>
Tested-by: Daire Byrne <daire@dneg.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1340f80f0 ]
In the gfs2 withdraw sequence, the dlm protocol is unmounted with a call
to lm_unmount. After a withdraw, users are allowed to unmount the
withdrawn file system. But at that point we may still have glocks left
over that we need to free via unmount's call to gfs2_gl_hash_clear.
These glocks may have never been completed because of whatever problem
caused the withdraw (IO errors or whatever).
Before this patch, function gdlm_put_lock would still try to call into
dlm to unlock these leftover glocks, which resulted in dlm returning
-EINVAL because the lock space was abandoned. These glocks were never
freed because there was no mechanism after that to free them.
This patch adds a check to gdlm_put_lock to see if the locking protocol
was inactive (DFL_UNMOUNT flag) and if so, free the glock and not
make the invalid call into dlm.
I could have combined this "if" with the one that follows, related to
leftover glock LVBs, but I felt the code was more readable with its own
if clause.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83e5dcbece ]
When skipping the tests due to a lack of system support for MTE we
currently print a message saying FAIL which makes it look like the test
failed even though the test did actually report KSFT_SKIP, creating some
confusion. Change the error message to say SKIP instead so things are
clearer.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210819172902.56211-1-broonie@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 74fc4f8287 ]
Currently, when creating an ingress qdisc on an indirect device before
the driver registered for callbacks, the driver will not have a chance
to register its filter configuration callbacks.
To fix that, modify the code such that it keeps track of all the ingress
qdiscs that call flow_indr_dev_setup_offload(). When a driver calls
flow_indr_dev_register(), go through the list of tracked ingress qdiscs
and call the driver callback entry point so as to give it a chance to
register its callback.
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbe34165cc ]
Fix buf allocation size (it needs to be 2 bytes larger). Found when
__alloc_size() annotations were added to kmalloc() interfaces.
In file included from ./include/linux/string.h:253,
from ./include/linux/bitmap.h:10,
from ./include/linux/cpumask.h:12,
from ./arch/x86/include/asm/paravirt.h:17,
from ./arch/x86/include/asm/irqflags.h:63,
from ./include/linux/irqflags.h:16,
from ./include/linux/rcupdate.h:26,
from ./include/linux/rculist.h:11,
from ./include/linux/pid.h:5,
from ./include/linux/sched.h:14,
from ./include/linux/blkdev.h:5,
from drivers/staging/rts5208/rtsx_scsi.c:12:
In function 'get_ms_information',
inlined from 'ms_sp_cmnd' at drivers/staging/rts5208/rtsx_scsi.c:2877:12,
inlined from 'rtsx_scsi_handler' at drivers/staging/rts5208/rtsx_scsi.c:3247:12:
./include/linux/fortify-string.h:54:29: warning: '__builtin_memcpy' forming offset [106, 107] is out
of the bounds [0, 106] [-Warray-bounds]
54 | #define __underlying_memcpy __builtin_memcpy
| ^
./include/linux/fortify-string.h:417:2: note: in expansion of macro '__underlying_memcpy'
417 | __underlying_##op(p, q, __fortify_size); \
| ^~~~~~~~~~~~~
./include/linux/fortify-string.h:463:26: note: in expansion of macro '__fortify_memcpy_chk'
463 | #define memcpy(p, q, s) __fortify_memcpy_chk(p, q, s, \
| ^~~~~~~~~~~~~~~~~~~~
drivers/staging/rts5208/rtsx_scsi.c:2851:3: note: in expansion of macro 'memcpy'
2851 | memcpy(buf + i, ms_card->raw_sys_info, 96);
| ^~~~~~
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-staging@lists.linux.dev
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210818044252.1533634-1-keescook@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b16ac5bf73 ]
libbpf CI has reported send_signal test is flaky although
I am not able to reproduce it in my local environment.
But I am able to reproduce with on-demand libbpf CI ([1]).
Through code analysis, the following is possible reason.
The failed subtest runs bpf program in softirq environment.
Since bpf_send_signal() only sends to a fork of "test_progs"
process. If the underlying current task is
not "test_progs", bpf_send_signal() will not be triggered
and the subtest will fail.
To reduce the chances where the underlying process is not
the intended one, this patch boosted scheduling priority to
-20 (highest allowed by setpriority() call). And I did
10 runs with on-demand libbpf CI with this patch and I
didn't observe any failures.
[1] https://github.com/libbpf/libbpf/actions/workflows/ondemand.yml
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210817190923.3186725-1-yhs@fb.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3faa49bce ]
Since the original TFO server code was implemented in commit
168a8f5805 ("tcp: TCP Fast Open Server -
main code path") the TFO server code has supported the sysctl bit flag
TFO_SERVER_COOKIE_NOT_REQD. Currently, when the TFO_SERVER_ENABLE and
TFO_SERVER_COOKIE_NOT_REQD sysctl bit flags are set, a server connection
will accept a SYN with N bytes of data (N > 0) that has no TFO cookie,
create a new fast open connection, process the incoming data in the SYN,
and make the connection ready for accepting. After accepting, the
connection is ready for read()/recvmsg() to read the N bytes of data in
the SYN, ready for write()/sendmsg() calls and data transmissions to
transmit data.
This commit changes an edge case in this feature by changing this
behavior to apply to (N >= 0) bytes of data in the SYN rather than only
(N > 0) bytes of data in the SYN. Now, a server will accept a data-less
SYN without a TFO cookie if TFO_SERVER_COOKIE_NOT_REQD is set.
Caveat! While this enables a new kind of TFO (data-less empty-cookie
SYN), some firewall rules setup may not work if they assume such packets
are not legit TFOs and will filter them.
Signed-off-by: Luke Hsiao <lukehsiao@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20210816205105.2533289-1-luke.w.hsiao@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b69eea82d3 ]
Modern-day mapping_set_error has the ability to squash the usual
negative error code into something appropriate for long-term storage in
a struct address_space -- ENOSPC becomes AS_ENOSPC, and everything else
becomes EIO. iomap squashes /everything/ to EIO, just as XFS did before
that, but this doesn't make sense.
Fix this by making it so that we can pass ENOSPC to userspace when
writeback fails due to space problems.
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87b8061bad ]
This fixes two issues that cause the sysrq sequence to be inadvertently
aborted on SCIF serial consoles:
- a NUL character remains in the RX queue after a break has been detected,
which is then passed on to uart_handle_sysrq_char()
- the break interrupt is handled twice on controllers with multiplexed ERI
and BRI interrupts
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20210816162201.28801-1-uli+renesas@fpond.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 020d86fc0d ]
The 'required-opps' property is considered optional, hence remove
the pr_err() in of_parse_required_opp() when we find the property is
missing.
While at it, also fix the return value of
of_get_required_opp_performance_state() when of_parse_required_opp()
fails, return a -ENODEV instead of the -EINVAL.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cafae4cd62 ]
LE Enhanced Connection Complete contains the Local RPA used in the
connection which must be used when set otherwise there could problems
when pairing since the address used by the remote stack could be the
Local RPA:
BLUETOOTH CORE SPECIFICATION Version 5.2 | Vol 4, Part E
page 2396
'Resolvable Private Address being used by the local device for this
connection. This is only valid when the Own_Address_Type (from the
HCI_LE_Create_Connection, HCI_LE_Set_Advertising_Parameters,
HCI_LE_Set_Extended_Advertising_Parameters, or
HCI_LE_Extended_Create_Connection commands) is set to 0x02 or
0x03, and the Controller generated a resolvable private address for the
local device using a non-zero local IRK. For other Own_Address_Type
values, the Controller shall return all zeros.'
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e7006de6c2 ]
We cannot detect a (perhaps buggy) controller that is sending us
a completion for a request that was already completed (for example
sending a completion twice), this phenomenon was seen in the wild
a few times.
So to protect against this, we use the upper 4 msbits of the nvme sqe
command_id to use as a 4-bit generation counter and verify it matches
the existing request generation that is incrementing on every execution.
The 16-bit command_id structure now is constructed by:
| xxxx | xxxxxxxxxxxx |
gen request tag
This means that we are giving up some possible queue depth as 12 bits
allow for a maximum queue depth of 4095 instead of 65536, however we
never create such long queues anyways so no real harm done.
Suggested-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Acked-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Tested-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b01a9d0ca ]
We already validate it when receiving the c2hdata pdu header
and this is not changing so this is a redundant check.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f865d0292f ]
The documented compatible string for the CPUs found on Tegra132 is
"nvidia,tegra132-denver", rather than the previously used compatible
string "nvidia,denver".
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 70e740ad55 ]
The configuration of USB VBUS regulators was borrowed from downstream
kernel, which is incorrect because the corresponding GPIOs are connected
to PROX_EN (A501 3G model) and LED_EN pins in accordance to the board
schematics. USB works fine with both GPIOs being disabled, so remove the
bogus USB VBUS regulators. The USB VBUS of USB3 is supplied from the fixed
5v system regulator and device-mode USB1 doesn't have VBUS switches.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79f5962bae ]
The maximum MTU was set to 2304, which is the maximum MSDU size. While
this is valid for normal WLAN interfaces, it is too low for monitor
interfaces. A monitor interface may receive and inject MPDU frames, and
the maximum MPDU frame size is larger than 2304. The MPDU may also
contain an A-MSDU frame, in which case the size may be much larger than
the MTU limit. Since the maximum size of an A-MSDU depends on the PHY
mode of the transmitting STA, it is not possible to set an exact MTU
limit for a monitor interface. Now the maximum MTU for a monitor
interface is unrestricted.
Signed-off-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Link: https://lore.kernel.org/r/20210628123246.2070558-1-johan.almbladh@anyfinetworks.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 554594567b ]
The variable dc->clk_mgr is checked in:
if (dc->clk_mgr && dc->clk_mgr->funcs->get_clock)
This indicates dc->clk_mgr can be NULL.
However, it is dereferenced in:
if (!dc->clk_mgr->funcs->get_clock)
To fix this null-pointer dereference, check dc->clk_mgr and the function
pointer dc->clk_mgr->funcs->get_clock earlier, and return if one of them
is NULL.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Tuo Li <islituo@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a211260c34 ]
The variable val is declared without initialization, and its address is
passed to amdgpu_i2c_get_byte(). In this function, the value of val is
accessed in:
DRM_DEBUG("i2c 0x%02x 0x%02x read failed\n",
addr, *val);
Also, when amdgpu_i2c_get_byte() returns, val may remain uninitialized,
but it is accessed in:
val &= ~amdgpu_connector->router.ddc_mux_control_pin;
To fix this possible uninitialized-variable access, initialize val to 0 in
amdgpu_i2c_router_select_ddc_port().
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Tuo Li <islituo@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 979aa51967 ]
Fix the following smatch warning:
wait_func_handle_exec_timeout() warn: should '1 << ent->idx' be a 64 bit type?
Use 1ULL, to have a 64 bit type variable.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eran Ben Elisha <eranbe@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba316be1b6 ]
struct sock.sk_timer should be used as a sock cleanup timer. However,
SCO uses it to implement sock timeouts.
This causes issues because struct sock.sk_timer's callback is run in
an IRQ context, and the timer callback function sco_sock_timeout takes
a spin lock on the socket. However, other functions such as
sco_conn_del and sco_conn_ready take the spin lock with interrupts
enabled.
This inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} lock usage could
lead to deadlocks as reported by Syzbot [1]:
CPU0
----
lock(slock-AF_BLUETOOTH-BTPROTO_SCO);
<Interrupt>
lock(slock-AF_BLUETOOTH-BTPROTO_SCO);
To fix this, we use delayed work to implement SCO sock timouts
instead. This allows us to avoid taking the spin lock on the socket in
an IRQ context, and corrects the misuse of struct sock.sk_timer.
As a note, cancel_delayed_work is used instead of
cancel_delayed_work_sync in sco_sock_set_timer and
sco_sock_clear_timer to avoid a deadlock. In the future, the call to
bh_lock_sock inside sco_sock_timeout should be changed to lock_sock to
synchronize with other functions using lock_sock. However, since
sco_sock_set_timer and sco_sock_clear_timer are sometimes called under
the locked socket (in sco_connect and __sco_sock_close),
cancel_delayed_work_sync might cause them to sleep until an
sco_sock_timeout that has started finishes running. But
sco_sock_timeout would also sleep until it can grab the lock_sock.
Using cancel_delayed_work is fine because sco_sock_timeout does not
change from run to run, hence there is no functional difference
between:
1. waiting for a timeout to finish running before scheduling another
timeout
2. scheduling another timeout while a timeout is running.
Link: https://syzkaller.appspot.com/bug?id=9089d89de0502e120f234ca0fc8a703f7368b31e [1]
Reported-by: syzbot+2f6d7c28bb4bf7e82060@syzkaller.appspotmail.com
Tested-by: syzbot+2f6d7c28bb4bf7e82060@syzkaller.appspotmail.com
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42716425ad ]
In tb_switch_default_link_ports(), while linking of ports,
only odd-numbered ports (1,3,5..) are considered and even-numbered
ports are not considered.
AMD host router has lane adapters at 2 and 3 and link ports at adapter 2
is not considered due to which lane bonding gets disabled.
Hence added a fix such that all ports are considered during
linking of ports.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a338619bd7 ]
When insmod zynqmp-dpsub.ko after rmmod it, system will hang with the
error log as below:
root@xilinx-zynqmp:~# insmod zynqmp-dpsub.ko
[ 88.391289] [drm] Initialized zynqmp-dpsub 1.0.0 20130509 for fd4a0000.display on minor 0
[ 88.529906] Console: switching to colour frame buffer device 128x48
[ 88.549402] zynqmp-dpsub fd4a0000.display: [drm] fb0: zynqmp-dpsubdrm frame buffer device
[ 88.571624] zynqmp-dpsub fd4a0000.display: ZynqMP DisplayPort Subsystem driver probed
root@xilinx-zynqmp:~# rmmod zynqmp_dpsub
[ 94.023404] Console: switching to colour dummy device 80x25
root@xilinx-zynqmp:~# insmod zynqmp-dpsub.ko
<hang here>
This is because that in zynqmp_dp_probe it tries to access some DP
registers while the DP controller is still in the reset state. When
running "rmmod zynqmp_dpsub", zynqmp_dp_reset(dp, true) in
zynqmp_dp_phy_exit is called to force the DP controller into the reset
state. Then insmod will call zynqmp_dp_probe to program the DP registers,
but at this moment the DP controller hasn't been brought out of the reset
state yet since the function zynqmp_dp_reset(dp, false) is called later and
this will result the system hang.
Releasing the reset to DP controller before any read/write operation to it
will fix this issue. And for symmetry, move zynqmp_dp_reset() call from
zynqmp_dp_phy_exit() to zynqmp_dp_remove().
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a19effb6db ]
The Runtime PM subsystem will force the device "fd4a0000.zynqmp-display"
to enter suspend state while booting if the following conditions are met:
- the usage counter is zero (pm_runtime_get_sync hasn't been called yet)
- no 'active' children (no zynqmp-dp-snd-xx node under dpsub node)
- no other device in the same power domain (dpdma node has no
"power-domains = <&zynqmp_firmware PD_DP>" property)
So there is a scenario as below:
1) DP device enters suspend state <- call zynqmp_gpd_power_off
2) zynqmp_disp_crtc_setup_clock <- configurate register VPLL_FRAC_CFG
3) pm_runtime_get_sync <- call zynqmp_gpd_power_on and clear previous
VPLL_FRAC_CFG configuration
4) clk_prepare_enable(disp->pclk) <- enable failed since VPLL_FRAC_CFG
configuration is corrupted
From above, we can see that pm_runtime_get_sync may clear register
VPLL_FRAC_CFG configuration and result the failure of clk enabling.
Putting pm_runtime_get_sync at the very beginning of the function
zynqmp_disp_crtc_atomic_enable can resolve this issue.
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56bd931ae5 ]
msm_atomic is doing vblank get/put's already,
currently there no need to duplicate the effort in MDP4
Fix warning:
...
WARNING: CPU: 3 PID: 79 at drivers/gpu/drm/drm_vblank.c:1194 drm_vblank_put+0x1cc/0x1d4
...
and multiple vblank time-outs:
...
msm 5100000.mdp: vblank time out, crtc=1
...
Tested on Nexus 7 2013 (deb), LTS 5.10.50.
Introduced by: 119ecb7fd3 ("drm/msm/mdp4: request vblank during modeset")
Signed-off-by: David Heidelberg <david@ixit.cz>
Link: https://lore.kernel.org/r/20210715060925.7880-1-david@ixit.cz
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4367355dd9 ]
When compiling with clang in certain configurations, an objtool warning
appears:
drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.o: warning: objtool:
ipq806x_gmac_probe() falls through to next function phy_modes()
This happens because the unreachable annotation in the third switch
statement is not eliminated. The compiler should know that the first
default case would prevent the second and third from being reached as
the comment notes but sanitizer options can make it harder for the
compiler to reason this out.
Help the compiler out by eliminating the unreachable() annotation and
unifying the default case error handling so that there is no objtool
warning, the meaning of the code stays the same, and there is less
duplication.
Reported-by: Sami Tolvanen <samitolvanen@google.com>
Tested-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84f3efbe5b ]
We have underscore (_) in node name leading to warning:
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: clocks: $nodename:0: 'clocks' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: clocks: xo_board: {'type': 'object'} is not allowed for {'compatible': ['fixed-clock'], '#clock-cells': [[0]], 'clock-frequency': [[19200000]], 'clock-output-names': ['xo_board'], 'phandle': [[115]]}
Fix this by changing node name to use dash (-)
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210308060826.3074234-10-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c678beca7 ]
We have underscore (_) in node name leading to warning:
arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon-cityman.dt.yaml: clocks: xo_board: {'type': 'object'} is not allowed for {'compatible': ['fixed-clock'], '#clock-cells': [[0]], 'clock-frequency': [[19200000]], 'phandle': [[26]]}
arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon-cityman.dt.yaml: clocks: sleep_clk: {'type': 'object'} is not allowed for {'compatible': ['fixed-clock'], '#clock-cells': [[0]], 'clock-frequency': [[32768]]}
Fix this by changing node name to use dash (-)
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210308060826.3074234-9-vkoul@kernel.org
[bjorn: Added clock-output-names to satisfy parent_names]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 52c9887fba ]
reg property should be array of values, here it is a single array,
leading to below warning:
arch/arm64/boot/dts/qcom/ipq8074-hk01.dt.yaml: soc: pci@10000000:reg:0: [268435456, 3869, 268439328, 168, 557056, 8192, 269484032, 4096] is too long
arch/arm64/boot/dts/qcom/ipq8074-hk01.dt.yaml: soc: pci@10000000:ranges: 'oneOf' conditional failed, one must be fixed:
arch/arm64/boot/dts/qcom/ipq8074-hk01.dt.yaml: soc: pci@10000000:ranges: 'oneOf' conditional failed, one must be fixed:
[[2164260864, 0, 270532608, 270532608, 0, 1048576, 2181038080, 0, 271581184, 271581184, 0, 13631488]] is not of type 'null'
[2164260864, 0, 270532608, 270532608, 0, 1048576, 2181038080, 0, 271581184, 271581184, 0, 13631488] is too long
arch/arm64/boot/dts/qcom/ipq8074-hk01.dt.yaml: soc: pci@20000000:reg:0: [536870912, 3869, 536874784, 168, 524288, 8192, 537919488, 4096] is too long
arch/arm64/boot/dts/qcom/ipq8074-hk01.dt.yaml: soc: pci@20000000:ranges: 'oneOf' conditional failed, one must be fixed:
arch/arm64/boot/dts/qcom/ipq8074-hk01.dt.yaml: soc: pci@20000000:ranges: 'oneOf' conditional failed, one must be fixed:
[[2164260864, 0, 538968064, 538968064, 0, 1048576, 2181038080, 0, 540016640, 540016640, 0, 13631488]] is not of type 'null'
[2164260864, 0, 538968064, 538968064, 0, 1048576, 2181038080, 0, 540016640, 540016640, 0, 13631488] is too long
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210308060826.3074234-17-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1fe0e1fa32 ]
Handle optional overrun-throttle-ms property as done for 8250_fsl in commit
6d7f677a2a ("serial: 8250: Rate limit serial port rx interrupts during
input overruns"). This can be used to rate limit the UART interrupts on
noisy lines that end up producing messages like the following:
ttyS ttyS2: 4 input overrun(s)
At least on droid4, the multiplexed USB and UART port is left to UART mode
by the bootloader for a debug console, and if a USB charger is connected
on boot, we get noise on the UART until the PMIC related drivers for PHY
and charger are loaded.
With this patch and overrun-throttle-ms = <500> we avoid the extra rx
interrupts.
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210727103533.51547-2-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d9b16054b ]
We must not call gfs2_consist (which does a file system withdraw) from
the freeze glock's freeze_go_xmote_bh function because the withdraw
will try to use the freeze glock, thus causing a glock recursion error.
This patch changes freeze_go_xmote_bh to call function
gfs2_assert_withdraw_delayed instead of gfs2_consist to avoid recursion.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4108b3e6db ]
These for-loops should test against v4l2_dv_timings_presets[i].bt.width,
not if i < v4l2_dv_timings_presets[i].bt.width. Luckily nothing ever broke,
since the smallest width is still a lot higher than the total number of
presets, but it is wrong.
The last item in the presets array is all 0, so the for-loop must stop
when it reaches that sentinel.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f809665ee7 ]
The range for analog gain mentioned in the datasheet is [0, 480].
The real gain formula mentioned in the datasheet is:
Gain = 512 / (512 – X)
Hence, values larger than 511 clearly makes no sense. The gain
register field is also documented to be of 9-bits in the datasheet.
Certainly, it is enough to infer that, the kernel driver currently
advertises an arbitrary analog gain max. Fix it by rectifying the
value as per the data sheet i.e. 480.
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51f93add36 ]
The frame_length_lines (0x0340) registers are hard-coded as follows:
- 4208x3118
frame_length_lines = 0x0c50
- 2104x1560
frame_length_lines = 0x0638
- 1048x780
frame_length_lines = 0x034c
The driver exposes the V4L2_CID_VBLANK control in read-only mode and
sets its value to vts_def - height, where vts_def is a mode-dependent
value coming from the supported_modes array. It is set using one of
the following macros defined in the driver:
#define IMX258_VTS_30FPS 0x0c98
#define IMX258_VTS_30FPS_2K 0x0638
#define IMX258_VTS_30FPS_VGA 0x034c
There's a clear mismatch in the value for the full resolution mode i.e.
IMX258_VTS_30FPS. Fix it by rectifying the macro with the value set for
the frame_length_lines register as stated above.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf2942a8b7 ]
The initialization sequence performed by the generic platform driver
pcie-designware-plat.c for a DWC based implementation doesn't work for
Tegra194. Tegra194 has a different initialization sequence requirement
which can only be satisfied by the Tegra194 specific platform driver
pcie-tegra194.c. So, remove the generic compatible string "snps,dw-pcie-ep"
from Tegra194's endpoint controller nodes.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 220ade7745 ]
Some time ago, I reported a calltrace issue
"did not find a suitable aggregator", please see[1].
After a period of analysis and reproduction, I find
that this problem is caused by concurrency.
Before the problem occurs, the bond structure is like follows:
bond0 - slaver0(eth0) - agg0.lag_ports -> port0 - port1
\
port0
\
slaver1(eth1) - agg1.lag_ports -> NULL
\
port1
If we run 'ifenslave bond0 -d eth1', the process is like below:
excuting __bond_release_one()
|
bond_upper_dev_unlink()[step1]
| | |
| | bond_3ad_lacpdu_recv()
| | ->bond_3ad_rx_indication()
| | spin_lock_bh()
| | ->ad_rx_machine()
| | ->__record_pdu()[step2]
| | spin_unlock_bh()
| | |
| bond_3ad_state_machine_handler()
| spin_lock_bh()
| ->ad_port_selection_logic()
| ->try to find free aggregator[step3]
| ->try to find suitable aggregator[step4]
| ->did not find a suitable aggregator[step5]
| spin_unlock_bh()
| |
| |
bond_3ad_unbind_slave() |
spin_lock_bh()
spin_unlock_bh()
step1: already removed slaver1(eth1) from list, but port1 remains
step2: receive a lacpdu and update port0
step3: port0 will be removed from agg0.lag_ports. The struct is
"agg0.lag_ports -> port1" now, and agg0 is not free. At the
same time, slaver1/agg1 has been removed from the list by step1.
So we can't find a free aggregator now.
step4: can't find suitable aggregator because of step2
step5: cause a calltrace since port->aggregator is NULL
To solve this concurrency problem, put bond_upper_dev_unlink()
after bond_3ad_unbind_slave(). In this way, we can invalid the port
first and skip this port in bond_3ad_state_machine_handler(). This
eliminates the situation that the slaver has been removed from the
list but the port is still valid.
[1]https://lore.kernel.org/netdev/10374.1611947473@famine/
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e6bc5987a ]
Swap reg and reg-names order and drop adi,input-justification
and adi,input-style to fix the following dtbs_check warnings:
arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dt.yaml: hdmi-transmitter@3d: adi,input-justification: False schema does not allow ['evenly']
arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dt.yaml: hdmi-transmitter@3d: adi,input-style: False schema does not allow [[1]]
arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dt.yaml: hdmi-transmitter@3d: reg-names:1: 'edid' was expected
arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dt.yaml: hdmi-transmitter@3d: reg-names:2: 'cec' was expected
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f728c4a9e8 ]
In error handling branch "if (WARN_ON(node == NUMA_NO_NODE))", the
previously allocated memories are not released. Doing this before
allocating memory eliminates memory leaks.
tj: Note that the condition only occurs when the arch code is pretty broken
and the WARN_ON might as well be BUG_ON().
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Reviewed-by: Lai Jiangshan <jiangshanlai@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 043c5bb3c4 ]
When loading in parallel multiple programs which use the same to-be
pinned map, it is possible that two instances of the loader will call
bpf_object__create_maps() at the same time. If the map doesn't exist
when both instances call bpf_object__reuse_map(), then one of the
instances will fail with EEXIST when calling bpf_map__pin().
Fix the race by retrying reusing a map if bpf_map__pin() returns
EEXIST. The fix is similar to the one in iproute2: e4c4685fd6e4 ("bpf:
Fix race condition with map pinning").
Before retrying the pinning, we don't do any special cleaning of an
internal map state. The closer code inspection revealed that it's not
required:
- bpf_object__create_map(): map->inner_map is destroyed after a
successful call, map->fd is closed if pinning fails.
- bpf_object__populate_internal_map(): created map elements is
destroyed upon close(map->fd).
- init_map_slots(): slots are freed after their initialization.
Signed-off-by: Martynas Pumputis <m@lambda.lt>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210726152001.34845-1-m@lambda.lt
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d07006f05 ]
The current behavior of 'tracex7' doesn't consist with other bpf samples
tracex{1..6}. Other samples do not require any argument to run with, but
tracex7 should be run with btrfs device argument. (it should be executed
with test_override_return.sh)
Currently, tracex7 doesn't have any description about how to run this
program and raises an unexpected error. And this result might be
confusing since users might not have a hunch about how to run this
program.
// Current behavior
# ./tracex7
sh: 1: Syntax error: word unexpected (expecting ")")
// Fixed behavior
# ./tracex7
ERROR: Run with the btrfs device argument!
In order to fix this error, this commit adds logic to report a message
and exit when running this program with a missing argument.
Additionally in test_override_return.sh, there is a problem with
multiple directory(tmpmnt) creation. So in this commit adds a line with
removing the directory with every execution.
Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20210727041056.23455-1-claudiajkang@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ccbdcc4d0 ]
The alloc_tty_driver failure is handled gracefully in hvsi_init. But
tty_register_driver is not. panic is called if that one fails.
So handle the failure of tty_register_driver gracefully too. This will
keep at least the console functional as it was enabled earlier by
console_initcall in hvsi_console_init. Instead of shooting down the
whole system.
This means, we disable interrupts and restore hvsi_wait back to
poll_for_state().
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210723074317.32690-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23411c7200 ]
While alloc_tty_driver failure in rs_init would mean we have much bigger
problem, there is no reason to panic when tty_register_driver fails
there. It can fail for various reasons.
So handle the failure gracefully. Actually handle them both while at it.
This will make at least the console functional as it was enabled earlier
by console_initcall in iss_console_init. Instead of shooting down the
whole system.
We move tty_port_init() after alloc_tty_driver(), so that we don't need
to destroy the port in case the latter function fails.
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: linux-xtensa@linux-xtensa.org
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210723074317.32690-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7aff291d0 ]
Oxford Semiconductor 950 serial port devices have a 128-byte FIFO and in
the enhanced (650) mode, which we select in `autoconfig_has_efr' with
the ECB bit set in the EFR register, they support the receive interrupt
trigger level selectable with FCR bits 7:6 from the set of 16, 32, 112,
120. This applies to the original OX16C950 discrete UART[1] as well as
950 cores embedded into more complex devices.
For these devices we set the default to 112, which sets an excessively
high level of 112 or 7/8 of the FIFO capacity, unlike with other port
types where we choose at most 1/2 of their respective FIFO capacities.
Additionally we don't make the trigger level configurable. Consequently
frequent input overruns happen with high bit rates where hardware flow
control cannot be used (e.g. terminal applications) even with otherwise
highly-performant systems.
Lower the default receive interrupt trigger level to 32 then, and make
it configurable. Document the trigger levels along with other port
types, including the set of 16, 32, 64, 112 for the transmit interrupt
as well[2].
References:
[1] "OX16C950 rev B High Performance UART with 128 byte FIFOs", Oxford
Semiconductor, Inc., DS-0031, Sep 05, Table 10: "Receiver Trigger
Levels", p. 22
[2] same, Table 9: "Transmit Interrupt Trigger Levels", p. 22
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260608480.37803@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3322ba0d7b ]
Kernel support for the newer PCI mio instructions can be toggled off
with the pci=nomio command line option which needs to integrate with
common code PCI option parsing. However this option then toggles static
branches which can't be toggled yet in an early_param() call.
Thus commit 9964f396f1 ("s390: fix setting of mio addressing control")
moved toggling the static branches to the PCI init routine.
With this setup however we can't check for mio support outside the PCI
code during early boot, i.e. before switching the static branches, which
we need to be able to export this as an ELF HWCAP.
Improve on this by turning mio availability into a machine flag that
gets initially set based on CONFIG_PCI and the facility bit and gets
toggled off if pci=nomio is found during PCI option parsing allowing
simple access to this machine flag after early init.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5492886c14 ]
In case of a jump label print the real address of the piece of code
where a mismatch was detected. This is right before the system panics,
so there is nothing revealed.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 323e0cb473 ]
Fix the following out-of-bounds warnings:
net/core/flow_dissector.c: In function '__skb_flow_dissect':
>> net/core/flow_dissector.c:1104:4: warning: 'memcpy' offset [24, 39] from the object at '<unknown>' is out of the bounds of referenced subobject 'saddr' with type 'struct in6_addr' at offset 8 [-Warray-bounds]
1104 | memcpy(&key_addrs->v6addrs, &iph->saddr,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1105 | sizeof(key_addrs->v6addrs));
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from include/linux/ipv6.h:5,
from net/core/flow_dissector.c:6:
include/uapi/linux/ipv6.h:133:18: note: subobject 'saddr' declared here
133 | struct in6_addr saddr;
| ^~~~~
>> net/core/flow_dissector.c:1059:4: warning: 'memcpy' offset [16, 19] from the object at '<unknown>' is out of the bounds of referenced subobject 'saddr' with type 'unsigned int' at offset 12 [-Warray-bounds]
1059 | memcpy(&key_addrs->v4addrs, &iph->saddr,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1060 | sizeof(key_addrs->v4addrs));
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from include/linux/ip.h:17,
from net/core/flow_dissector.c:5:
include/uapi/linux/ip.h:103:9: note: subobject 'saddr' declared here
103 | __be32 saddr;
| ^~~~~
The problem is that the original code is trying to copy data into a
couple of struct members adjacent to each other in a single call to
memcpy(). So, the compiler legitimately complains about it. As these
are just a couple of members, fix this by copying each one of them in
separate calls to memcpy().
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
Link: https://github.com/KSPP/linux/issues/109
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/d5ae2e65-1f18-2577-246f-bada7eee6ccd@intel.com/
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6321c7acb8 ]
Fix the following out-of-bounds warning:
In function 'ip_copy_addrs',
inlined from '__ip_queue_xmit' at net/ipv4/ip_output.c:517:2:
net/ipv4/ip_output.c:449:2: warning: 'memcpy' offset [40, 43] from the object at 'fl' is out of the bounds of referenced subobject 'saddr' with type 'unsigned int' at offset 36 [-Warray-bounds]
449 | memcpy(&iph->saddr, &fl4->saddr,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
450 | sizeof(fl4->saddr) + sizeof(fl4->daddr));
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The problem is that the original code is trying to copy data into a
couple of struct members adjacent to each other in a single call to
memcpy(). This causes a legitimate compiler warning because memcpy()
overruns the length of &iph->saddr and &fl4->saddr. As these are just
a couple of struct members, fix this by using direct assignments,
instead of memcpy().
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
Link: https://github.com/KSPP/linux/issues/109
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/d5ae2e65-1f18-2577-246f-bada7eee6ccd@intel.com/
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b7e9f25e5 ]
Each test case can have a set of sub-tests, where each sub-test can
run the cBPF/eBPF test snippet with its own data_size and expected
result. Before, the end of the sub-test array was indicated by both
data_size and result being zero. However, most or all of the internal
eBPF tests has a data_size of zero already. When such a test also had
an expected value of zero, the test was never run but reported as
PASS anyway.
Now the test runner always runs the first sub-test, regardless of the
data_size and result values. The sub-test array zero-termination only
applies for any additional sub-tests.
There are other ways fix it of course, but this solution at least
removes the surprise of eBPF tests with a zero result always succeeding.
Signed-off-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210721103822.3755111-1-johan.almbladh@anyfinetworks.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95f71f12aa ]
The printing message "PSP loading VCN firmware" is mis-leading because
people might think driver is loading VCN firmware. Actually when this
message is printed, driver is just preparing some VCN ucode, not loading
VCN firmware yet. The actual VCN firmware loading will be in the PSP block
hw_init. Fix the printing message
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Christian Konig <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd98d2895d ]
The ethtool compat ioctl handling is hidden away in net/socket.c,
which introduces a couple of minor oddities:
- The implementation may end up diverging, as seen in the RXNFC
extension in commit 84a1d9c482 ("net: ethtool: extend RXNFC
API to support RSS spreading of filter matches") that does not work
in compat mode.
- Most architectures do not need the compat handling at all
because u64 and compat_u64 have the same alignment.
- On x86, the conversion is done for both x32 and i386 user space,
but it's actually wrong to do it for x32 and cannot work there.
- On 32-bit Arm, it never worked for compat oabi user space, since
that needs to do the same conversion but does not.
- It would be nice to get rid of both compat_alloc_user_space()
and copy_in_user() throughout the kernel.
None of these actually seems to be a serious problem that real
users are likely to encounter, but fixing all of them actually
leads to code that is both shorter and more readable.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23e55639b8 ]
[why]
The units of the time_per_pixel variable were incorrect, this had to be
changed for the code to properly function.
[how]
The change was very straightforward, only required one line of code to
be changed where the calculation was done.
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Oliver Logush <oliver.logush@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8990f96a01 ]
Some versions of the MC firmware wrongly report 0 for register base
address of the DPMCP associated with child DPRC objects thus rendering
them unusable. This is particularly troublesome in ACPI boot scenarios
where the legacy way of extracting this base address from the device
tree does not apply.
Given that DPMCPs share the same base address, workaround this by using
the base address extracted from the root DPRC container.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Link: https://lore.kernel.org/r/20210715140718.8513-8-laurentiu.tudor@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df00609821 ]
On Armadillo-800-EVA with CONFIG_DEBUG_SPINLOCK=y:
BUG: spinlock bad magic on CPU#0, swapper/1
lock: lcdc0_device+0x10c/0x308, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
CPU: 0 PID: 1 Comm: swapper Not tainted 5.11.0-rc5-armadillo-00036-gbbca04be7a80-dirty #287
Hardware name: Generic R8A7740 (Flattened Device Tree)
[<c010c3c8>] (unwind_backtrace) from [<c010a49c>] (show_stack+0x10/0x14)
[<c010a49c>] (show_stack) from [<c0159534>] (do_raw_spin_lock+0x20/0x94)
[<c0159534>] (do_raw_spin_lock) from [<c040858c>] (dev_pm_get_subsys_data+0x8c/0x11c)
[<c040858c>] (dev_pm_get_subsys_data) from [<c05fbcac>] (genpd_add_device+0x78/0x2b8)
[<c05fbcac>] (genpd_add_device) from [<c0412db4>] (of_genpd_add_device+0x34/0x4c)
[<c0412db4>] (of_genpd_add_device) from [<c0a1ea74>] (board_staging_register_device+0x11c/0x148)
[<c0a1ea74>] (board_staging_register_device) from [<c0a1eac4>] (board_staging_register_devices+0x24/0x28)
of_genpd_add_device() is called before platform_device_register(), as it
needs to attach the genpd before the device is probed. But the spinlock
is only initialized when the device is registered.
Fix this by open-coding the spinlock initialization, cfr.
device_pm_init_common() in the internal drivers/base code, and in the
SuperH early platform code.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/57783ece7ddae55f2bda2f59f452180bff744ea0.1626257398.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bcacbf06c8 ]
Currently the composite driver encodes the MaxPower field of
the configuration descriptor by reading the c->MaxPower of the
usb_configuration only if it is non-zero, otherwise it falls back
to using the value hard-coded in CONFIG_USB_GADGET_VBUS_DRAW.
However, there are cases when a configuration must explicitly set
bMaxPower to 0, particularly if its bmAttributes also has the
Self-Powered bit set, which is a valid combination.
This is specifically called out in the USB PD specification section
9.1, in which a PDUSB device "shall report zero in the bMaxPower
field after negotiating a mutually agreeable Contract", and also
verified by the USB Type-C Functional Test TD.4.10.2 Sink Power
Precedence Test.
The fix allows the c->MaxPower to be used for encoding the bMaxPower
even if it is 0, if the self-powered bit is also set. An example
usage of this would be for a ConfigFS gadget to be dynamically
updated by userspace when the Type-C connection is determined to be
operating in Power Delivery mode.
Co-developed-by: Ronak Vijay Raheja <rraheja@codeaurora.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Ronak Vijay Raheja <rraheja@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20210720080907.30292-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61136a12cb ]
mv_ehci_enable() did not disable and unprepare clocks in case of
failures of phy_init(). Besides, it did not take into account failures
of ehci_clock_enable() (in effect, failures of clk_prepare_enable()).
The patch fixes both issues and gets rid of redundant wrappers around
clk_prepare_enable() and clk_disable_unprepare() to simplify this a bit.
Found by Linux Driver Verification project (linuxtesting.org).
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Link: https://lore.kernel.org/r/20210708083056.21543-1-novikov@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ae0123960 ]
f_ncm tx timeout can call us with null skb to flush
a pending frame. In this case skb is NULL to begin
with but ceases to be null after dev->wrap() completes.
In such a case in->maxpacket will be read, even though
we've failed to check that 'in' is not NULL.
Though I've never observed this fail in practice,
however the 'flush operation' simply does not make sense with
a null usb IN endpoint - there's nowhere to flush to...
(note that we're the gadget/device, and IN is from the point
of view of the host, so here IN actually means outbound...)
Cc: Brooke Basile <brookebasile@gmail.com>
Cc: "Bryan O'Donoghue" <bryan.odonoghue@linaro.org>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20210701114834.884597-6-zenczykowski@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 373e2829e7 ]
Ensure that the adapter->q_vector[MAX_Q_VECTORS] array isn't accessed
beyond its size. It was fixed by using a local variable num_q_vectors
as a limit for loop index, and ensure that num_q_vectors is not bigger
than MAX_Q_VECTORS.
Suggested-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fed31a4dd3 ]
This commit fixes several typos where CONFIG_TASKS_RCU_TRACE should
instead be CONFIG_TASKS_TRACE_RCU. Among other things, these typos
could cause CONFIG_TASKS_TRACE_RCU_READ_MB=y kernels to suffer from
memory-ordering bugs that could result in false-positive quiescent
states and too-short grace periods.
Signed-off-by: Zhouyi Zhou <zhouzhouyi@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56f0729a51 ]
drm_file->master pointers should be protected by
drm_device.master_mutex or drm_file.master_lookup_lock when being
dereferenced.
However, in drm_lease.c, there are multiple instances where
drm_file->master is accessed and dereferenced while neither lock is
held. This makes drm_lease.c vulnerable to use-after-free bugs.
We address this issue in 2 ways:
1. Add a new drm_file_get_master() function that calls drm_master_get
on drm_file->master while holding on to
drm_file.master_lookup_lock. Since drm_master_get increments the
reference count of master, this prevents master from being freed until
we unreference it with drm_master_put.
2. In each case where drm_file->master is directly accessed and
eventually dereferenced in drm_lease.c, we wrap the access in a call
to the new drm_file_get_master function, then unreference the master
pointer once we are done using it.
Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210712043508.11584-6-desmondcheongzx@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b0860a3cf ]
Currently, drm_file.master pointers should be protected by
drm_device.master_mutex when being dereferenced. This is because
drm_file.master is not invariant for the lifetime of drm_file. If
drm_file is not the creator of master, then drm_file.is_master is
false, and a call to drm_setmaster_ioctl will invoke
drm_new_set_master, which then allocates a new master for drm_file and
puts the old master.
Thus, without holding drm_device.master_mutex, the old value of
drm_file.master could be freed while it is being used by another
concurrent process.
However, it is not always possible to lock drm_device.master_mutex to
dereference drm_file.master. Through the fbdev emulation code, this
might occur in a deep nest of other locks. But drm_device.master_mutex
is also the outermost lock in the nesting hierarchy, so this leads to
potential deadlocks.
To address this, we introduce a new spin lock at the bottom of the
lock hierarchy that only serializes drm_file.master. With this change,
the value of drm_file.master changes only when both
drm_device.master_mutex and drm_file.master_lookup_lock are
held. Hence, any process holding either of those locks can ensure that
the value of drm_file.master will not change concurrently.
Since no lock depends on the new drm_file.master_lookup_lock, when
drm_file.master is dereferenced, but drm_device.master_mutex cannot be
held, we can safely protect the master pointer with
drm_file.master_lookup_lock.
Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210712043508.11584-5-desmondcheongzx@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5eff9585de ]
Inside drm_clients_info, the rcu_read_lock is held to lock
pid_task()->comm. However, within this protected section, a call to
drm_is_current_master is made, which involves a mutex lock in a future
patch. However, this is illegal because the mutex lock might block
while in the RCU read-side critical section.
Since drm_is_current_master isn't protected by rcu_read_lock, we avoid
this by moving it out of the RCU critical section.
The following report came from intel-gfx ci's
igt@debugfs_test@read_all_entries testcase:
=============================
[ BUG: Invalid wait context ]
5.13.0-CI-Patchwork_20515+ #1 Tainted: G W
-----------------------------
debugfs_test/1101 is trying to lock:
ffff888132d901a8 (&dev->master_mutex){+.+.}-{3:3}, at:
drm_is_current_master+0x1e/0x50
other info that might help us debug this:
context-{4:4}
3 locks held by debugfs_test/1101:
#0: ffff88810fdffc90 (&p->lock){+.+.}-{3:3}, at:
seq_read_iter+0x53/0x3b0
#1: ffff888132d90240 (&dev->filelist_mutex){+.+.}-{3:3}, at:
drm_clients_info+0x63/0x2a0
#2: ffffffff82734220 (rcu_read_lock){....}-{1:2}, at:
drm_clients_info+0x1b1/0x2a0
stack backtrace:
CPU: 8 PID: 1101 Comm: debugfs_test Tainted: G W
5.13.0-CI-Patchwork_20515+ #1
Hardware name: Intel Corporation CometLake Client Platform/CometLake S
UDIMM (ERB/CRB), BIOS CMLSFWR1.R00.1263.D00.1906260926 06/26/2019
Call Trace:
dump_stack+0x7f/0xad
__lock_acquire.cold.78+0x2af/0x2ca
lock_acquire+0xd3/0x300
? drm_is_current_master+0x1e/0x50
? __mutex_lock+0x76/0x970
? lockdep_hardirqs_on+0xbf/0x130
__mutex_lock+0xab/0x970
? drm_is_current_master+0x1e/0x50
? drm_is_current_master+0x1e/0x50
? drm_is_current_master+0x1e/0x50
drm_is_current_master+0x1e/0x50
drm_clients_info+0x107/0x2a0
seq_read_iter+0x178/0x3b0
seq_read+0x104/0x150
full_proxy_read+0x4e/0x80
vfs_read+0xa5/0x1b0
ksys_read+0x5a/0xd0
do_syscall_64+0x39/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210712043508.11584-3-desmondcheongzx@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d14f5c702 ]
In the smk_access_entry() function, if no matching rule is found
in the rust_list, a negative error code will be used to perform bit
operations with the MAY_ enumeration value. This is semantically
wrong. This patch fixes this issue.
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fef773fc81 ]
Yonghong Song report:
The bpf selftest tc_bpf failed with latest bpf-next.
The following is the command to run and the result:
$ ./test_progs -n 132
[ 40.947571] bpf_testmod: loading out-of-tree module taints kernel.
test_tc_bpf:PASS:test_tc_bpf__open_and_load 0 nsec
test_tc_bpf:PASS:bpf_tc_hook_create(BPF_TC_INGRESS) 0 nsec
test_tc_bpf:PASS:bpf_tc_hook_create invalid hook.attach_point 0 nsec
test_tc_bpf_basic:PASS:bpf_obj_get_info_by_fd 0 nsec
test_tc_bpf_basic:PASS:bpf_tc_attach 0 nsec
test_tc_bpf_basic:PASS:handle set 0 nsec
test_tc_bpf_basic:PASS:priority set 0 nsec
test_tc_bpf_basic:PASS:prog_id set 0 nsec
test_tc_bpf_basic:PASS:bpf_tc_attach replace mode 0 nsec
test_tc_bpf_basic:PASS:bpf_tc_query 0 nsec
test_tc_bpf_basic:PASS:handle set 0 nsec
test_tc_bpf_basic:PASS:priority set 0 nsec
test_tc_bpf_basic:PASS:prog_id set 0 nsec
libbpf: Kernel error message: Failed to send filter delete notification
test_tc_bpf_basic:FAIL:bpf_tc_detach unexpected error: -3 (errno 3)
test_tc_bpf:FAIL:test_tc_internal ingress unexpected error: -3 (errno 3)
The failure seems due to the commit
cfdf0d9ae7 ("rtnetlink: use nlmsg_notify() in rtnetlink_send()")
Deal with ESRCH error in nlmsg_notify() even the report variable is zero.
Reported-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Link: https://lore.kernel.org/r/20210719051816.11762-1-yajun.deng@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 98a6543917 ]
The user can pass in any value to the driver through the 'ioctl'
interface. The driver dost not check, which may cause DoS bugs.
The following log reveals it:
divide error: 0000 [#1] PREEMPT SMP KASAN PTI
RIP: 0010:SetOverlayViewPort+0x133/0x5f0 drivers/video/fbdev/kyro/STG4000OverlayDevice.c:476
Call Trace:
kyro_dev_overlay_viewport_set drivers/video/fbdev/kyro/fbdev.c:378 [inline]
kyrofb_ioctl+0x2eb/0x330 drivers/video/fbdev/kyro/fbdev.c:603
do_fb_ioctl+0x1f3/0x700 drivers/video/fbdev/core/fbmem.c:1171
fb_ioctl+0xeb/0x130 drivers/video/fbdev/core/fbmem.c:1185
vfs_ioctl fs/ioctl.c:48 [inline]
__do_sys_ioctl fs/ioctl.c:753 [inline]
__se_sys_ioctl fs/ioctl.c:739 [inline]
__x64_sys_ioctl+0x19b/0x220 fs/ioctl.c:739
do_syscall_64+0x32/0x80 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xae
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1626235762-2590-1-git-send-email-zheyuma97@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0dc6c59892 ]
Since new code doesn't take old clk names in account, it does fixes
error:
msm_dsi 4700000.mdss_dsi: dev_pm_opp_set_clkname: Couldn't find clock: -2
and following kernel oops introduced by
b0530eb119 ("drm/msm/dpu: Use OPP API to set clk/perf state").
Also removes warning about deprecated clock names.
Tested against linux-5.10.y LTS on Nexus 7 2013.
Reviewed-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: David Heidelberg <david@ixit.cz>
Link: https://lore.kernel.org/r/20210707131453.24041-1-david@ixit.cz
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 226d528512 ]
To avoid races between iavf_init_task(), iavf_reset_task(),
iavf_watchdog_task(), iavf_adminq_task() as well as the shutdown and
remove functions more locking is required.
The current protection by __IAVF_IN_CRITICAL_TASK is needed in
additional places.
- The reset task performs state transitions, therefore needs locking.
- The adminq task acts on replies from the PF in
iavf_virtchnl_completion() which may alter the states.
- The init task is not only run during probe but also if a VF gets stuck
to reinitialize it.
- The shutdown function performs a state transition.
- The remove function performs a state transition and also free's
resources.
iavf_lock_timeout() is introduced to avoid waiting infinitely
and cause a deadlock. Rather unlock and print a warning.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 22c8fd71d3 ]
The iavf watchdog task overrides adapter->state to __IAVF_RESETTING
when it detects a pending reset. Then schedules iavf_reset_task() which
takes care of the reset.
The reset task is capable of handling the reset without changing
adapter->state. In fact we lose the state information when the watchdog
task prematurely changes the adapter state. This may lead to a crash if
instead of the reset task the iavf_remove() function gets called before
the reset task.
In that case (if we were in state __IAVF_RUNNING previously) the
iavf_remove() function triggers iavf_close() which fails to close the
device because of the incorrect state information.
This may result in a crash due to pending interrupts.
kernel BUG at drivers/pci/msi.c:357!
[...]
Call Trace:
[<ffffffffbddf24dd>] pci_disable_msix+0x3d/0x50
[<ffffffffc08d2a63>] iavf_reset_interrupt_capability+0x23/0x40 [iavf]
[<ffffffffc08d312a>] iavf_remove+0x10a/0x350 [iavf]
[<ffffffffbddd3359>] pci_device_remove+0x39/0xc0
[<ffffffffbdeb492f>] __device_release_driver+0x7f/0xf0
[<ffffffffbdeb49c3>] device_release_driver+0x23/0x30
[<ffffffffbddcabb4>] pci_stop_bus_device+0x84/0xa0
[<ffffffffbddcacc2>] pci_stop_and_remove_bus_device+0x12/0x20
[<ffffffffbddf361f>] pci_iov_remove_virtfn+0xaf/0x160
[<ffffffffbddf3bcc>] sriov_disable+0x3c/0xf0
[<ffffffffbddf3ca3>] pci_disable_sriov+0x23/0x30
[<ffffffffc0667365>] i40e_free_vfs+0x265/0x2d0 [i40e]
[<ffffffffc0667624>] i40e_pci_sriov_configure+0x144/0x1f0 [i40e]
[<ffffffffbddd5307>] sriov_numvfs_store+0x177/0x1d0
Code: 00 00 e8 3c 25 e3 ff 49 c7 86 88 08 00 00 00 00 00 00 5b 41 5c 41 5d 41 5e 41 5f 5d c3 48 8b 7b 28 e8 0d 44
RIP [<ffffffffbbbf1068>] free_msi_irqs+0x188/0x190
The solution is to not touch the adapter->state in iavf_watchdog_task()
and let the reset task handle the state transition.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97683c851f ]
The naming of the regulator is problematic. VCC is usually a supply
voltage whereas these devices have a separate VREF pin.
Secondly, the regulator core might have provided a stub regulator if
a real regulator wasn't provided. That would in turn have failed to
provide a voltage when queried. So reality was that there was no way
to use the internal reference.
In order to avoid breaking any dts out in the wild, make sure to fallback
to the original vcc naming if vref is not available.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210627163244.1090296-9-jic23@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4919ff59c ]
Currently, when userspace reads a datagram with a buffer that is
smaller than this datagram, the data will be truncated and only
part of it can be received by users. It doesn't seem right that
users don't know the datagram size and have to use a huge buffer
to read it to avoid the truncation.
This patch to fix it by keeping the skb in rcv queue until the
whole data is read by users. Only the last msg of the datagram
will be marked with MSG_EOR, just as TCP/SCTP does.
Note that this will work as above only when MSG_EOR is set in the
flags parameter of recvmsg(), so that it won't break any old user
applications.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14858dcc3b ]
Updating the current_state field of struct pci_dev the way it is done
in pci_enable_device_flags() before calling do_pci_enable_device() may
not work. For example, if the given PCI device depends on an ACPI
power resource whose _STA method initially returns 0 ("off"), but the
config space of the PCI device is accessible and the power state
retrieved from the PCI_PM_CTRL register is D0, the current_state
field in the struct pci_dev representing that device will get out of
sync with the power.state of its ACPI companion object and that will
lead to power management issues going forward.
To avoid such issues, make pci_enable_device_flags() call
pci_update_current_state() which takes ACPI device power management
into account, if present, to retrieve the current power state of the
device.
Link: https://lore.kernel.org/lkml/20210314000439.3138941-1-luzmaximilian@gmail.com/
Reported-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c445535c3e ]
Marking TSC as unstable has a side effect of marking sched_clock as
unstable when TSC is still being used as the sched_clock. This is not
desirable. Hyper-V ultimately uses a paravirtualized clock source that
provides a stable scheduler clock even on systems without TscInvariant
CPU capability. Hence, mark_tsc_unstable() call should be called _after_
scheduler clock has been changed to the paravirtualized clocksource. This
will prevent any unwanted manipulation of the sched_clock. Only TSC will
be correctly marked as unstable.
Signed-off-by: Ani Sinha <ani@anisinha.ca>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Tested-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20210713030522.1714803-1-ani@anisinha.ca
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97eb31384a ]
When loading a BPF program with a pinned map, the loader checks whether
the pinned map can be reused, i.e. their properties match. To derive
such of the pinned map, the loader invokes BPF_OBJ_GET_INFO_BY_FD and
then does the comparison.
Unfortunately, on < 4.12 kernels the BPF_OBJ_GET_INFO_BY_FD is not
available, so loading the program fails with the following error:
libbpf: failed to get map info for map FD 5: Invalid argument
libbpf: couldn't reuse pinned map at
'/sys/fs/bpf/tc/globals/cilium_call_policy': parameter
mismatch"
libbpf: map 'cilium_call_policy': error reusing pinned map
libbpf: map 'cilium_call_policy': failed to create:
Invalid argument(-22)
libbpf: failed to load object 'bpf_overlay.o'
To fix this, fallback to derivation of the map properties via
/proc/$PID/fdinfo/$MAP_FD if BPF_OBJ_GET_INFO_BY_FD fails with EINVAL,
which can be used as an indicator that the kernel doesn't support
the latter.
Signed-off-by: Martynas Pumputis <m@lambda.lt>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20210712125552.58705-1-m@lambda.lt
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8db11aebdb ]
The logic at dib8000_get_init_prbs() has a few issues:
1. the tables used there has an extra unused value at the beginning;
2. the dprintk() message doesn't write the right value when
transmission mode is not 8K;
3. the array overflow validation is done by the callers.
Rewrite the code to fix such issues.
This should also shut up those smatch warnings:
drivers/media/dvb-frontends/dib8000.c:2125 dib8000_get_init_prbs() error: buffer overflow 'lut_prbs_8k' 14 <= 14
drivers/media/dvb-frontends/dib8000.c:2129 dib8000_get_init_prbs() error: buffer overflow 'lut_prbs_2k' 14 <= 14
drivers/media/dvb-frontends/dib8000.c:2131 dib8000_get_init_prbs() error: buffer overflow 'lut_prbs_4k' 14 <= 14
drivers/media/dvb-frontends/dib8000.c:2134 dib8000_get_init_prbs() error: buffer overflow 'lut_prbs_8k' 14 <= 14
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1698ecb218 ]
Symptom is random switching of speakers when using multichannel.
Repeatedly running speakertest -c8 occasionally starts with
channels jumbled. This is fixed with HD_CTL_WHOLSMP.
The other bit looks beneficial and apears harmless in testing so
I'd suggest adding it too.
Documentation says: HD_CTL_WHILSMP_SET
Wait for whole sample. When this bit is set MAI transmit will start
only when there is at least one whole sample available in the fifo.
Documentation says: HD_CTL_CHALIGN_SET
Channel Align When Overflow. This bit is used to realign the audio
channels in case of an overflow.
If this bit is set, after the detection of an overflow, equal
amount of dummy words to the missing words will be written to fifo,
filling up the broken sample and maintaining alignment.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210525132354.297468-7-maxime@cerno.tech
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 22e5fe2a2a ]
userfaultfd assumes that the enabled features are set once and never
changed after UFFDIO_API ioctl succeeded.
However, currently, UFFDIO_API can be called concurrently from two
different threads, succeed on both threads and leave userfaultfd's
features in non-deterministic state. Theoretically, other uffd operations
(ioctl's and page-faults) can be dispatched while adversely affected by
such changes of features.
Moreover, the writes to ctx->state and ctx->features are not ordered,
which can - theoretically, again - let userfaultfd_ioctl() think that
userfaultfd API completed, while the features are still not initialized.
To avoid races, it is arguably best to get rid of ctx->state. Since there
are only 2 states, record the API initialization in ctx->features as the
uppermost bit and remove ctx->state.
Link: https://lkml.kernel.org/r/20210808020724.1022515-3-namit@vmware.com
Fixes: 9cd75c3cd4 ("userfaultfd: non-cooperative: add ability to report non-PF events from uffd descriptor")
Signed-off-by: Nadav Amit <namit@vmware.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Axel Rasmussen <axelrasmussen@google.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Peter Xu <peterx@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 52d83df682 ]
When CONFIG_TRIM_UNUSED_KSYMS is enabled, I see some warnings like this:
nm: arch/x86/entry/vdso/vdso32/note.o: no symbols
$NM (both GNU nm and llvm-nm) warns when no symbol is found in the
object. Suppress the stderr.
Fangrui Song mentioned binutils>=2.37 `nm -q` can be used to suppress
"no symbols" [1], and llvm-nm>=13.0.0 supports -q as well.
We cannot use it for now, but note it as a TODO.
[1]: https://sourceware.org/bugzilla/show_bug.cgi?id=27408
Fixes: bbda5ec671 ("kbuild: simplify dependency generation for CONFIG_TRIM_UNUSED_KSYMS")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bea6a94a27 ]
Starting with following patch MIPS Malta is not able to boot:
| commit 79edff1206
| Author: Rob Herring <robh@kernel.org>
| scripts/dtc: Update to upstream version v1.6.0-51-g183df9e9c2b9
The reason is the alignment test added to the fdt_ro_probe_(). To fix
this issue, we need to make sure that fdt_buf is aligned.
Since the dtc patch was designed to uncover potential issue, I handle
initial MIPS Malta patch as initial bug.
Fixes: e81a8c7dab ("MIPS: Malta: Setup RAM regions via DT")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9605f75cf3 ]
The prepare_compress_overwrite() gets/locks a page to prepare a read, and calls
f2fs_read_multi_pages() which checks EOF first. If there's any page beyond EOF,
we unlock the page and set cc->rpages[i] = NULL, which we can't put the page
anymore. This makes page leak, so let's fix by putting that page.
Fixes: a949dc5f2c ("f2fs: compress: fix race condition of overwrite vs truncate")
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 827f02842e ]
In f2fs_write_multi_pages(), f2fs_compress_pages() allocates pages for
compression work in cc->cpages[]. Then, f2fs_write_compressed_pages() initiates
bio submission. But, if there's any error before submitting the IOs like early
f2fs_cp_error(), previously it didn't free cpages by f2fs_compress_free_page().
Let's fix memory leak by putting that just before deallocating cc->cpages.
Fixes: 4c8ff7095b ("f2fs: support data compression")
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8dc3047c4 ]
We need to unmap pages from userspace process before removing pagecache
in punch_hole() like we did in f2fs_setattr().
Similar change:
commit 5e44f8c374 ("ext4: hole-punch use truncate_pagecache_range")
Fixes: fbfa2cc58d ("f2fs: add file operations")
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit adf9ea89c7 ]
In below path, it will return ENOENT if filesystem is shutdown:
- f2fs_map_blocks
- f2fs_get_dnode_of_data
- f2fs_get_node_page
- __get_node_page
- read_node_page
- is_sbi_flag_set(sbi, SBI_IS_SHUTDOWN)
return -ENOENT
- force return value from ENOENT to 0
It should be fine for read case, since it indicates a hole condition,
and caller could use .m_next_pgofs to skip the hole and continue the
lookup.
However it may cause confusing for write case, since leaving a hole
there, and said nothing was wrong doesn't help.
There is at least one case from dax_iomap_actor() will complain that,
so fix this in prior to supporting dax in f2fs.
xfstest generic/388 reports below warning:
ubuntu godown: xfstests-induced forced shutdown of /mnt/scratch_f2fs:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 485833 at fs/dax.c:1127 dax_iomap_actor+0x339/0x370
Call Trace:
iomap_apply+0x1c4/0x7b0
? dax_iomap_rw+0x1c0/0x1c0
dax_iomap_rw+0xad/0x1c0
? dax_iomap_rw+0x1c0/0x1c0
f2fs_file_write_iter+0x5ab/0x970 [f2fs]
do_iter_readv_writev+0x273/0x2e0
do_iter_write+0xab/0x1f0
vfs_iter_write+0x21/0x40
iter_file_splice_write+0x287/0x540
do_splice+0x37c/0xa60
__x64_sys_splice+0x15f/0x3a0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
ubuntu godown: xfstests-induced forced shutdown of /mnt/scratch_f2fs:
------------[ cut here ]------------
RIP: 0010:dax_iomap_pte_fault.isra.0+0x72e/0x14a0
Call Trace:
dax_iomap_fault+0x44/0x70
f2fs_dax_huge_fault+0x155/0x400 [f2fs]
f2fs_dax_fault+0x18/0x30 [f2fs]
__do_fault+0x4e/0x120
do_fault+0x3cf/0x7a0
__handle_mm_fault+0xa8c/0xf20
? find_held_lock+0x39/0xd0
handle_mm_fault+0x1b6/0x480
do_user_addr_fault+0x320/0xcd0
? rcu_read_lock_sched_held+0x67/0xc0
exc_page_fault+0x77/0x3f0
? asm_exc_page_fault+0x8/0x30
asm_exc_page_fault+0x1e/0x30
Fixes: 83a3bfdb5a ("f2fs: indicate shutdown f2fs to allow unmount successfully")
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad126ebdde ]
There is a missing place we forgot to account .skipped_gc_rwsem, fix it.
Fixes: 6f8d445506 ("f2fs: avoid fi->i_gc_rwsem[WRITE] lock in f2fs_gc")
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d78dfde33 ]
Since commit e1a1ef84cd ("KVM: PPC: Book3S: Allocate guest TCEs on
demand too"), pages for TCE tables for KVM guests are allocated only
when needed. This allows skipping any update when clearing TCEs. This
works mostly fine as TCE updates are handled when the MMU is enabled.
The realmode handlers fail with H_TOO_HARD when pages are not yet
allocated, except when clearing a TCE in which case KVM prints a warning
and proceeds to dereference a NULL pointer, which crashes the host OS.
This has not been caught so far as the change in commit e1a1ef84cd is
reasonably new, and POWER9 runs mostly radix which does not use realmode
handlers. With hash, the default TCE table is memset() by QEMU when the
machine is reset which triggers page faults and the KVM TCE device's
kvm_spapr_tce_fault() handles those with MMU on. And the huge DMA
windows are not cleared by VMs which instead successfully create a DMA
window big enough to map the VM memory 1:1 and then VMs just map
everything without clearing.
This started crashing now as commit 381ceda88c ("powerpc/pseries/iommu:
Make use of DDW for indirect mapping") added a mode when a dymanic DMA
window not big enough to map the VM memory 1:1 but it is used anyway,
and the VM now is the first (i.e. not QEMU) to clear a just created
table. Note that upstream QEMU needs to be modified to trigger the VM to
trigger the host OS crash.
This replaces WARN_ON_ONCE_RM() with a check and return, and adds
another warning if TCE is not being cleared.
Fixes: e1a1ef84cd ("KVM: PPC: Book3S: Allocate guest TCEs on demand too")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210827040706.517652-1-aik@ozlabs.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35b72573e9 ]
The current hash algorithm used for hashing cookie keys is really bad,
producing almost no dispersion (after a test kernel build, ~30000 files
were split over just 18 out of the 32768 hash buckets).
Borrow the full_name_hash() hash function into fscache to do the hashing
for cookie keys and, in the future, volume keys.
I don't want to use full_name_hash() as-is because I want the hash value to
be consistent across arches and over time as the hash value produced may
get used on disk.
I can also optimise parts of it away as the key will always be a padded
array of aligned 32-bit words.
Fixes: ec0328e46d ("fscache: Maintain a catalogue of allocated cookies")
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
cc: linux-cachefs@redhat.com
Link: https://lore.kernel.org/r/162431201844.2908479.8293647220901514696.stgit@warthog.procyon.org.uk/
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8b9280303 ]
lscpu() uses core_siblings to list the number of sockets in the
system. core_siblings is set using topology_core_cpumask.
While optimizing the powerpc bootup path, Commit 4ca234a9cb
("powerpc/smp: Stop updating cpu_core_mask"). it was found that
updating cpu_core_mask() ended up taking a lot of time. It was thought
that on Powerpc, cpu_core_mask() would always be same as
cpu_cpu_mask() i.e number of sockets will always be equal to number of
nodes. As an optimization, cpu_core_mask() was made a snapshot of
cpu_cpu_mask().
However that was found to be false with PowerPc KVM guests, where each
node could have more than one socket. So with Commit c47f892d7a
("powerpc/smp: Reintroduce cpu_core_mask"), cpu_core_mask was updated
based on chip_id but in an optimized way using some mask manipulations
and chip_id caching.
However on non-PowerNV and non-pseries KVM guests (i.e not
implementing cpu_to_chip_id(), continued to use a copy of
cpu_cpu_mask().
There are two issues that were noticed on such systems
1. lscpu would report one extra socket.
On a IBM,9009-42A (aka zz system) which has only 2 chips/ sockets/
nodes, lscpu would report
Architecture: ppc64le
Byte Order: Little Endian
CPU(s): 160
On-line CPU(s) list: 0-159
Thread(s) per core: 8
Core(s) per socket: 6
Socket(s): 3 <--------------
NUMA node(s): 2
Model: 2.2 (pvr 004e 0202)
Model name: POWER9 (architected), altivec supported
Hypervisor vendor: pHyp
Virtualization type: para
L1d cache: 32K
L1i cache: 32K
L2 cache: 512K
L3 cache: 10240K
NUMA node0 CPU(s): 0-79
NUMA node1 CPU(s): 80-159
2. Currently cpu_cpu_mask is updated when a core is
added/removed. However its not updated when smt mode switching or on
CPUs are explicitly offlined. However all other percpu masks are
updated to ensure only active/online CPUs are in the masks.
This results in build_sched_domain traces since there will be CPUs in
cpu_cpu_mask() but those CPUs are not present in SMT / CACHE / MC /
NUMA domains. A loop of threads running smt mode switching and core
add/remove will soon show this trace.
Hence cpu_cpu_mask has to be update at smt mode switch.
This will have impact on cpu_core_mask(). cpu_core_mask() is a
snapshot of cpu_cpu_mask. Different CPUs within the same socket will
end up having different cpu_core_masks since they are snapshots at
different points of time. This means when lscpu will start reporting
many more sockets than the actual number of sockets/ nodes / chips.
Different ways to handle this problem:
A. Update the snapshot aka cpu_core_mask for all CPUs whenever
cpu_cpu_mask is updated. This would a non-optimal solution.
B. Instead of a cpumask_var_t, make cpu_core_map a cpumask pointer
pointing to cpu_cpu_mask. However percpu cpumask pointer is frowned
upon and we need a clean way to handle PowerPc KVM guest which is
not a snapshot.
C. Update cpu_core_masks all PowerPc systems like in PowerPc KVM
guests using mask manipulations. This approach is relatively simple
and unifies with the existing code.
D. On top of 3, we could also resurrect get_physical_package_id which
could return a nid for the said CPU. However this is not needed at this
time.
Option C is the preferred approach for now.
While this is somewhat a revert of Commit 4ca234a9cb ("powerpc/smp:
Stop updating cpu_core_mask").
1. Plain revert has some conflicts
2. For chip_id == -1, the cpu_core_mask is made identical to
cpu_cpu_mask, unlike previously where cpu_core_mask was set to a core
if chip_id doesn't exist.
This goes by the principle that if chip_id is not exposed, then
sockets / chip / node share the same set of CPUs.
With the fix, lscpu o/p would be
Architecture: ppc64le
Byte Order: Little Endian
CPU(s): 160
On-line CPU(s) list: 0-159
Thread(s) per core: 8
Core(s) per socket: 6
Socket(s): 2 <--------------
NUMA node(s): 2
Model: 2.2 (pvr 004e 0202)
Model name: POWER9 (architected), altivec supported
Hypervisor vendor: pHyp
Virtualization type: para
L1d cache: 32K
L1i cache: 32K
L2 cache: 512K
L3 cache: 10240K
NUMA node0 CPU(s): 0-79
NUMA node1 CPU(s): 80-159
Fixes: 4ca234a9cb ("powerpc/smp: Stop updating cpu_core_mask")
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210826100401.412519-3-srikar@linux.vnet.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1782663897 ]
After the L1 saves its PMU SPRs but before loading the L2's PMU SPRs,
switch the pmcregs_in_use field in the L1 lppaca to the value advertised
by the L2 in its VPA. On the way out of the L2, set it back after saving
the L2 PMU registers (if they were in-use).
This transfers the PMU liveness indication between the L1 and L2 at the
points where the registers are not live.
This fixes the nested HV bug for which a workaround was added to the L0
HV by commit 63279eeb7f ("KVM: PPC: Book3S HV: Always save guest pmu
for guest capable of nesting"), which explains the problem in detail.
That workaround is no longer required for guests that include this bug
fix.
Fixes: 360cae3137 ("KVM: PPC: Book3S HV: Nested guest entry via hypercall")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Link: https://lore.kernel.org/r/20210811160134.904987-10-npiggin@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 313bf281f2 ]
clk_get_rate() returns unsigned long and currently this driver stores the
return value in u32 type, resulting the below warning:
Fixed smatch warnings:
drivers/scsi/ufs/ufs-exynos.c:286 exynos_ufs_get_clk_info()
warn: wrong type for 'ufs->mclk_rate' (should be 'ulong')
drivers/scsi/ufs/ufs-exynos.c:287 exynos_ufs_get_clk_info()
warn: wrong type for 'pclk_rate' (should be 'ulong')
Link: https://lore.kernel.org/r/20210819171131.55912-1-alim.akhtar@samsung.com
Fixes: 55f4b1f736 ("scsi: ufs: ufs-exynos: Add UFS host support for Exynos SoCs")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d7d6dac8f ]
The __kvmhv_copy_tofrom_guest_radix function was introduced along with
nested HV guest support. It uses the platform's Radix MMU quadrants to
provide a nested hypervisor with fast access to its nested guests
memory (H_COPY_TOFROM_GUEST hypercall). It has also since been added
as a fast path for the kvmppc_ld/st routines which are used during
instruction emulation.
The commit def0bfdbd6 ("powerpc: use probe_user_read() and
probe_user_write()") changed the low level copy function from
raw_copy_from_user to probe_user_read, which adds a check to
access_ok. In powerpc that is:
static inline bool __access_ok(unsigned long addr, unsigned long size)
{
return addr < TASK_SIZE_MAX && size <= TASK_SIZE_MAX - addr;
}
and TASK_SIZE_MAX is 0x0010000000000000UL for 64-bit, which means that
setting the two MSBs of the effective address (which correspond to the
quadrant) now cause access_ok to reject the access.
This was not caught earlier because the most common code path via
kvmppc_ld/st contains a fallback (kvm_read_guest) that is likely to
succeed for L1 guests. For nested guests there is no fallback.
Another issue is that probe_user_read (now __copy_from_user_nofault)
does not return the number of bytes not copied in case of failure, so
the destination memory is not being cleared anymore in
kvmhv_copy_from_guest_radix:
ret = kvmhv_copy_tofrom_guest_radix(vcpu, eaddr, to, NULL, n);
if (ret > 0) <-- always false!
memset(to + (n - ret), 0, ret);
This patch fixes both issues by skipping access_ok and open-coding the
low level __copy_to/from_user_inatomic.
Fixes: def0bfdbd6 ("powerpc: use probe_user_read() and probe_user_write()")
Signed-off-by: Fabiano Rosas <farosas@linux.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210805212616.2641017-2-farosas@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d36207b848 ]
On the i.MX8M*, the TF-A exposes a SiP (Silicon Provider) service
for DDR frequency scaling. The imx8m-ddrc-devfreq driver calls the
SiP and then does clk_set_parent on the DDR muxes to synchronize
the clock tree.
Since 936c383673 ("clk: imx: fix composite peripheral flags"),
these TF-A managed muxes have SET_PARENT_GATE set, which results
in imx8m-ddrc-devfreq's clk_set_parent after SiP failing with -EBUSY:
echo 25000000 > userspace/set_freq
imx8m-ddrc-devfreq 3d400000.memory-controller: failed to set
dram_apb parent: -16
Fix this by adding a new i.MX composite flag for firmware managed
clocks, which clears SET_PARENT_GATE.
This is safe to do, because updating the Linux clock tree to reflect
reality will always be glitch-free.
Fixes: 936c383673 ("clk: imx: fix composite peripheral flags")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20210810151432.9228-1-a.fatoum@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 786537063b ]
A quirk was recently added for Elan devices that has same device match
as an entry earlier in the list. The i2c_hid_lookup_quirk function will
always return the last match in the list, so the new entry shadows the
old entry. The quirk in the previous entry, I2C_HID_QUIRK_BOGUS_IRQ,
silenced a flood of messages which have reappeared in the 5.13 kernel.
This change moves the two quirk flags into the same entry.
Fixes: ca66a6770b (HID: i2c-hid: Skip ELAN power-on command after reset)
Signed-off-by: Jim Broadus <jbroadus@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d0e28a6145 ]
CONFIG_MTD_PHYSMAP_OF is not longer enabled as it depends on
MTD_PHYSMAP which is not enabled.
This is a regression from commit 642b1e8dbe ("mtd: maps: Merge
physmap_of.c into physmap-core.c"), which added the extra dependency.
Add CONFIG_MTD_PHYSMAP=y so this stays in the config, as Christophe said
it is useful for build coverage.
Fixes: 642b1e8dbe ("mtd: maps: Merge physmap_of.c into physmap-core.c")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Acked-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210817045407.2445664-3-joel@jms.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ccc89737aa ]
This driver has some left over "return 1" on failure style code mixed with
"return negative error codes" style code. The caller doesn't care so we
should just convert everything to return negative error codes.
Then there was a problem that there were two variables used to store error
codes which just resulted in confusion. If qedf_alloc_bdq() returned a
negative error code, we accidentally returned success instead of
propagating the error code. So get rid of the "rc" variable and use
"status" every where.
Also remove the "status = 0" initialization so that these sorts of bugs
will be detected by the compiler in the future.
Link: https://lore.kernel.org/r/20210810085023.GA23998@kili
Fixes: 61d8658b4a ("scsi: qedf: Add QLogic FastLinQ offload FCoE driver framework.")
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4dbe57d46d ]
This function had some left over code that returned 1 on error instead
negative error codes. Convert everything to use negative error codes. The
caller treats all non-zero returns the same so this does not affect run
time.
A couple places set "rc" instead of "status" so those error paths ended up
returning success by mistake. Get rid of the "rc" variable and use
"status" everywhere.
Remove the bogus "status = 0" initialization, as a future proofing measure
so the compiler will warn about uninitialized error codes.
Link: https://lore.kernel.org/r/20210810084753.GD23810@kili
Fixes: ace7f46ba5 ("scsi: qedi: Add QLogic FastLinQ offload iSCSI driver framework.")
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c7248bb8d ]
When a LPAR is migratable, we should consider the maximum possible NUMA
node instead of the number of NUMA nodes from the actual system.
The DT property 'ibm,current-associativity-domains' defines the maximum
number of nodes the LPAR can see when running on that box. But if the
LPAR is being migrated on another box, it may see up to the nodes
defined by 'ibm,max-associativity-domains'. So if a LPAR is migratable,
that value should be used.
Unfortunately, there is no easy way to know if an LPAR is migratable or
not. The hypervisor exports the property 'ibm,migratable-partition' in
the case it set to migrate partition, but that would not mean that the
current partition is migratable.
Without this patch, when a LPAR is started on a 2 node box and then
migrated to a 3 node box, the hypervisor may spread the LPAR's CPUs on
the 3rd node. In that case if a CPU from that 3rd node is added to the
LPAR, it will be wrongly assigned to the node because the kernel has
been set to use up to 2 nodes (the configuration of the departure node).
With this patch applies, the CPU is correctly added to the 3rd node.
Fixes: f9f130ff2e ("powerpc/numa: Detect support for coregroup")
Signed-off-by: Laurent Dufour <ldufour@linux.ibm.com>
Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210511073136.17795-1-ldufour@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d46dd04cb ]
Since bc1c56e9bb transport->srcport may by unset, causing
get_srcport() to return 0 when called. Fix this by querying the port
from the underlying socket instead of the transport.
Fixes: bc1c56e9bb (SUNRPC: prevent port reuse on transports which don't request it)
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f99fa50880 ]
The xprtrdma client code currently relies on the task that initiated the
connect to hold the XPRT_LOCK for the duration of the connection
attempt. If the task is woken early, due to some other event, then that
lock could get released early.
Avoid races by using the same mechanism that the socket code uses of
transferring lock ownership to the RDMA connect worker itself. That
frees us to call rpcrdma_xprt_disconnect() directly since we're now
guaranteed exclusion w.r.t. other callers.
Fixes: 4cf44be6f1 ("xprtrdma: Fix recursion into rpcrdma_xprt_disconnect()")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2dc3e5fad ]
We really should not call rpc_wake_up_queued_task_set_status() with
xprt->snd_task as an argument unless we are certain that is actually an
rpc_task.
Fixes: 0445f92c5d ("SUNRPC: Fix disconnection races")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6236a98b3 ]
The intention of the layout barrier is to ensure that we do not update
the layout to match an older value than the current expectation. Fix the
test in pnfs_layout_stateid_blocked() to reflect that it is legal for
the seqid of the stateid to match that of the barrier.
Fixes: aa95edf309 ("NFSv4/pnfs: Fix the layout barrier update")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45baadaad7 ]
A zero value for the layout barrier indicates that it has been cleared
(since seqid '0' is an illegal value), so we should always allow it to
be updated.
Fixes: d29b468da4 ("pNFS/NFSv4: Improve rejection of out-of-order layouts")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e20772cbdf ]
If NFS_LAYOUT_RETURN_REQUESTED is set, but there is no value set for
the layout plh_return_seq, we can end up in a livelock loop in which
every layout segment retrieved by a new call to layoutget is immediately
invalidated by pnfs_layout_need_return().
To get around this, we should just set plh_return_seq to the current
value of the layout stateid's seqid.
Fixes: d474f96104 ("NFS: Don't return layout segments that are in use")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 173735c346 ]
Due to link order, dma_debug_init is called before debugfs has a chance
to initialize (via debugfs_init which also happens in the core initcall
stage), so the directories for dma-debug are never created.
Decouple dma_debug_fs_init from dma_debug_init and defer its init until
core_initcall_sync (after debugfs has been initialized) while letting
dma-debug initialization occur as soon as possible to catch any early
mappings, as suggested in [1].
[1] https://lore.kernel.org/linux-iommu/YIgGa6yF%2Fadg8OSN@kroah.com/
Fixes: 15b28bbcd5 ("dma-debug: move initialization to common code")
Signed-off-by: Anthony Iliopoulos <ailiop@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 946e1052cd ]
Don't call printk() when CONFIG_PRINTK is not set.
Fixes the following build errors:
or1k-linux-ld: arch/openrisc/kernel/entry.o: in function `_external_irq_handler':
(.text+0x804): undefined reference to `printk'
(.text+0x804): relocation truncated to fit: R_OR1K_INSN_REL_26 against undefined symbol `printk'
Fixes: 9d02a4283e ("OpenRISC: Boot code")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Cc: Stafford Horne <shorne@gmail.com>
Cc: openrisc@lists.librecores.org
Signed-off-by: Stafford Horne <shorne@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d4bf15a7ce ]
I recently found a case where de->name_len is 0 in f2fs_fill_dentries()
easily reproduced, and finally set the fsck flag.
Thread A Thread B
- f2fs_readdir
- f2fs_read_inline_dir
- ctx->pos = d.max
- f2fs_add_dentry
- f2fs_add_inline_entry
- do_convert_inline_dir
- f2fs_add_regular_entry
- f2fs_readdir
- f2fs_fill_dentries
- set_sbi_flag(sbi, SBI_NEED_FSCK)
Process A opens the folder, and has been reading without closing it.
During this period, Process B created a file under the folder (occupying
multiple f2fs_dir_entry, exceeding the d.max of the inline dir). After
creation, process A uses the d.max of inline dir to read it again, and
it will read that de->name_len is 0.
And Chao pointed out that w/o inline conversion, the race condition still
can happen as below:
dir_entry1: A
dir_entry2: B
dir_entry3: C
free slot: _
ctx->pos: ^
Thread A is traversing directory,
ctx-pos moves to below position after readdir() by thread A:
AAAABBBB___
^
Then thread B delete dir_entry2, and create dir_entry3.
Thread A calls readdir() to lookup dirents starting from middle
of new dirent slots as below:
AAAACCCCCC_
^
In these scenarios, the file system is not damaged, and it's hard to
avoid it. But we can bypass tagging FSCK flag if:
a) bit_pos (:= ctx->pos % d->max) is non-zero and
b) before bit_pos moves to first valid dir_entry.
Fixes: ddf06b753a ("f2fs: fix to trigger fsck if dirent.name_len is zero")
Signed-off-by: Yangtao Li <frank.li@vivo.com>
[Chao: clean up description]
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d04691d373 ]
After commit 7cbd631d4dec ("cpuidle: pseries: Fixup CEDE0 latency only
for POWER10 onwards"), pseries_idle_probe() is no longer inlined when
compiling with clang, which causes a modpost warning:
WARNING: modpost: vmlinux.o(.text+0xc86a54): Section mismatch in
reference from the function pseries_idle_probe() to the function
.init.text:fixup_cede0_latency()
The function pseries_idle_probe() references
the function __init fixup_cede0_latency().
This is often because pseries_idle_probe lacks a __init
annotation or the annotation of fixup_cede0_latency is wrong.
pseries_idle_probe() is a non-init function, which calls
fixup_cede0_latency(), which is an init function, explaining the
mismatch. pseries_idle_probe() is only called from
pseries_processor_idle_init(), which is an init function, so mark
pseries_idle_probe() as __init so there is no more warning.
Fixes: 054e44ba99 ("cpuidle: pseries: Add function to parse extended CEDE records")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210803211547.1093820-1-nathan@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6cae77f1b ]
commit 7c6986ade6 ("powerpc/stacktrace: Fix spurious "stale" traces in raise_backtrace_ipi()")
introduces udelay() call without including the linux/delay.h header.
This may happen to work on master but the header that declares the
functionshould be included nonetheless.
Fixes: 7c6986ade6 ("powerpc/stacktrace: Fix spurious "stale" traces in raise_backtrace_ipi()")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210729180103.15578-1-msuchanek@suse.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50741b70b0 ]
Commit d947fb4c96 ("cpuidle: pseries: Fixup exit latency for
CEDE(0)") sets the exit latency of CEDE(0) based on the latency values
of the Extended CEDE states advertised by the platform
On POWER9 LPARs, the firmwares advertise a very low value of 2us for
CEDE1 exit latency on a Dedicated LPAR. The latency advertized by the
PHYP hypervisor corresponds to the latency required to wakeup from the
underlying hardware idle state. However the wakeup latency from the
LPAR perspective should include
1. The time taken to transition the CPU from the Hypervisor into the
LPAR post wakeup from platform idle state
2. Time taken to send the IPI from the source CPU (waker) to the idle
target CPU (wakee).
1. can be measured via timer idle test, where we queue a timer, say
for 1ms, and enter the CEDE state. When the timer fires, in the timer
handler we compute how much extra timer over the expected 1ms have we
consumed. On a a POWER9 LPAR the numbers are
CEDE latency measured using a timer (numbers in ns)
N Min Median Avg 90%ile 99%ile Max Stddev
400 2601 5677 5668.74 5917 6413 9299 455.01
1. and 2. combined can be determined by an IPI latency test where we
send an IPI to an idle CPU and in the handler compute the time
difference between when the IPI was sent and when the handler ran. We
see the following numbers on POWER9 LPAR.
CEDE latency measured using an IPI (numbers in ns)
N Min Median Avg 90%ile 99%ile Max Stddev
400 711 7564 7369.43 8559 9514 9698 1200.01
Suppose, we consider the 99th percentile latency value measured using
the IPI to be the wakeup latency, the value would be 9.5us This is in
the ballpark of the default value of 10us.
Hence, use the exit latency of CEDE(0) based on the latency values
advertized by platform only from POWER10 onwards. The values
advertized on POWER10 platforms is more realistic and informed by the
latency measurements. For earlier platforms stick to the default value
of 10us. The fix was suggested by Michael Ellerman.
Fixes: d947fb4c96 ("cpuidle: pseries: Fixup exit latency for CEDE(0)")
Reported-by: Enrico Joedecke <joedecke@de.ibm.com>
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1626676399-15975-2-git-send-email-ego@linux.vnet.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62004871e1 ]
It is possible for the primary IPoIB network device associated with any
RDMA device to fail to join certain multicast groups preventing IPv6
neighbor discovery and possibly other network ULPs from working
correctly. The IPv4 broadcast group is not affected as the IPoIB network
device handles joining that multicast group directly.
This is because the primary IPoIB network device uses the pkey at ndex 0
in the associated RDMA device's pkey table. Anytime the pkey value of
index 0 changes, the primary IPoIB network device automatically modifies
it's broadcast address (i.e. /sys/class/net/[ib0]/broadcast), since the
broadcast address includes the pkey value, and then bounces carrier. This
includes initial pkey assignment, such as when the pkey at index 0
transitions from the opa default of invalid (0x0000) to some value such as
the OPA default pkey for Virtual Fabric 0: 0x8001 or when the fabric
manager is restarted with a configuration change causing the pkey at index
0 to change. Many network ULPs are not sensitive to the carrier bounce and
are not expecting the broadcast address to change including the linux IPv6
stack. This problem does not affect IPoIB child network devices as their
pkey value is constant for all time.
To mitigate this issue, change the default pkey in at index 0 to 0x8001 to
cover the predominant case and avoid issues as ipoib comes up and the FM
sweeps.
At some point, ipoib multicast support should automatically fix
non-broadcast addresses as it does with the primary broadcast address.
Fixes: 7724105686 ("IB/hfi1: add driver files")
Link: https://lore.kernel.org/r/20210715160445.142451.47651.stgit@awfm-01.cornelisnetworks.com
Suggested-by: Josh Collier <josh.d.collier@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6fffe52fb3 ]
The rk3036/rk3328 pll types were converted to checking the lock status
via the internal register in january 2020, so don't need the grf
reference since then.
But it was forgotten to remove grf check when deciding between the
pll rate ops (read-only vs. read-write), so a clock driver without
the needed grf reference might've been put into the read-only mode
just because the grf reference was missing.
This affected the rk356x that needs to reclock certain plls at boot.
Fix this by removing the check for the grf for selecting the utilized
operations.
Suggested-by: Heiko Stuebner <heiko@sntech.de>
Fixes: 7f6ffbb885 ("clk: rockchip: convert rk3036 pll type to use internal lock status")
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
[adjusted the commit message, adjusted the fixes tag]
Link: https://lore.kernel.org/r/20210728180034.717953-3-pgwipeout@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit baf8d6899b ]
The PWM pins on North Bridge on Armada 37xx can be configured into PWM
or GPIO functions. When in PWM function, each pin can also be configured
to drive low on 0 and tri-state on 1 (LED mode).
The current definitions handle this by declaring two pin groups for each
pin:
- group "pwmN" with functions "pwm" and "gpio"
- group "ledN_od" ("od" for open drain) with functions "led" and "gpio"
This is semantically incorrect. The correct definition for each pin
should be one group with three functions: "pwm", "led" and "gpio".
Change the "pwmN" groups to support "led" function.
Remove "ledN_od" groups. This cannot break backwards compatibility with
older device trees: no device tree uses it since there is no PWM driver
for this SOC yet. Also "ledN_od" groups are not even documented.
Fixes: b835d69530 ("pinctrl: armada-37xx: swap polarity on LED group")
Signed-off-by: Marek Behún <kabel@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210719112938.27594-1-kabel@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4abaa9eeb ]
The power supply states of discharging, charging, full, etc, represent
state of charging, not the capacity level of the battery (for which
we have a separate property). Current HID usage tables to not allow
for expressing charging state of the batteries found in generic
styli, so we should simply assume that the battery is discharging
even if current capacity is at 100% when battery strength reporting
is done via HID interface. In fact, we were doing just that before
commit 581c448476.
This change helps UIs to not mis-represent fully charged batteries in
styli as being charging/topping-off.
Fixes: 581c448476 ("HID: input: map digitizer battery usage")
Reported-by: Kenneth Albanowski <kenalba@google.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fcb461e2bc upstream.
There is an issue that when PCIe switch is connected to an Armada 3700
board, there will be lots of warnings about PIO errors when reading the
config space. According to Aardvark PIO read and write sequence in HW
specification, the current way to check PIO status has the following
issues:
1) For PIO read operation, it reports the error message, which should be
avoided according to HW specification.
2) For PIO read and write operations, it only checks PIO operation complete
status, which is not enough, and error status should also be checked.
This patch aligns the code with Aardvark PIO read and write sequence in HW
specification on PIO status check and fix the warnings when reading config
space.
[pali: Fix CRS handling when CRSSVE is not enabled]
Link: https://lore.kernel.org/r/20210722144041.12661-2-pali@kernel.org
Tested-by: Victor Gu <xigu@marvell.com>
Signed-off-by: Evan Wang <xswang@marvell.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Victor Gu <xigu@marvell.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org # b1bd571447 ("PCI: aardvark: Indicate error in 'val' when config read fails")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 64f160e19e upstream.
In commit 6df6ba974a ("PCI: aardvark: Remove PCIe outbound window
configuration") was removed aardvark PCIe outbound window configuration and
commit description said that was recommended solution by HW designers.
But that commit completely removed support for configuring PCIe IO
resources without removing PCIe IO 'ranges' from DTS files. After that
commit PCIe IO space started to be treated as PCIe MEM space and accessing
it just caused kernel crash.
Moreover implementation of PCIe outbound windows prior that commit was
incorrect. It completely ignored offset between CPU address and PCIe bus
address and expected that in DTS is CPU address always same as PCIe bus
address without doing any checks. Also it completely ignored size of every
PCIe resource specified in 'ranges' DTS property and expected that every
PCIe resource has size 128 MB (also for PCIe IO range). Again without any
check. Apparently none of PCIe resource has in DTS specified size of 128
MB. So it was completely broken and thanks to how aardvark mask works,
configuration was completely ignored.
This patch reverts back support for PCIe outbound window configuration but
implementation is a new without issues mentioned above. PCIe outbound
window is required when DTS specify in 'ranges' property non-zero offset
between CPU and PCIe address space. To address recommendation by HW
designers as specified in commit description of 6df6ba974a, set default
outbound parameters as PCIe MEM access without translation and therefore
for this PCIe 'ranges' it is not needed to configure PCIe outbound window.
For PCIe IO space is needed to configure aardvark PCIe outbound window.
This patch fixes kernel crash when trying to access PCIe IO space.
Link: https://lore.kernel.org/r/20210624215546.4015-2-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # 6df6ba974a ("PCI: aardvark: Remove PCIe outbound window configuration")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8bd29bd49 upstream.
The pciconfig_read() syscall reads PCI configuration space using
hardware-dependent config accessors.
If the read fails on PCI, most accessors don't return an error; they
pretend the read was successful and got ~0 data from the device, so the
syscall returns success with ~0 data in the buffer.
When the accessor does return an error, pciconfig_read() normally fills the
user's buffer with ~0 and returns an error in errno. But after
e4585da22a ("pci syscall.c: Switch to refcounting API"), we don't fill
the buffer with ~0 for the EPERM "user lacks CAP_SYS_ADMIN" error.
Userspace may rely on the ~0 data to detect errors, but after e4585da22a,
that would not detect CAP_SYS_ADMIN errors.
Restore the original behaviour of filling the buffer with ~0 when the
CAP_SYS_ADMIN check fails.
[bhelgaas: commit log, fold in Nathan's fix
https://lore.kernel.org/r/20210803200836.500658-1-nathan@kernel.org]
Fixes: e4585da22a ("pci syscall.c: Switch to refcounting API")
Link: https://lore.kernel.org/r/20210729233755.1509616-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 00823dcbdd upstream.
Previously we assumed that all Root Ports and Switch Downstream Ports
supported Link Bandwidth Notification. Per spec, this is only required
for Ports supporting Links wider than x1 and/or multiple Link speeds
(PCIe r5.0, sec 7.5.3.6).
Because we assumed all Ports supported it, we tried to set up a Bandwidth
Notification IRQ, which failed for devices that don't support IRQs at all,
which meant pcieport didn't attach to the Port at all.
Check the Link Bandwidth Notification Capability bit and enable the service
only when the Port supports it.
[bhelgaas: commit log]
Fixes: e8303bb7a7 ("PCI/LINK: Report degraded links via link bandwidth notification")
Link: https://lore.kernel.org/r/20210512213314.7778-1-stuart.w.hayes@gmail.com
Signed-off-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 65ddf65648 upstream.
This patch fixes below problems of sb/cp sanity check:
- in sanity_check_raw_superi(), it missed to consider log header
blocks while cp_payload check.
- in f2fs_sanity_check_ckpt(), it missed to check nat_bits_blocks.
Cc: <stable@kernel.org>
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b30d0289de upstream.
The merge_fdt_bootargs() function by definition consumes more than 1024
bytes of stack because it has a 1024 byte command line on the stack,
meaning that we always get a warning when building this file:
arch/arm/boot/compressed/atags_to_fdt.c: In function 'merge_fdt_bootargs':
arch/arm/boot/compressed/atags_to_fdt.c:98:1: warning: the frame size of 1032 bytes is larger than 1024 bytes [-Wframe-larger-than=]
However, as this is the decompressor and we know that it has a very shallow
call chain, and we do not actually risk overflowing the kernel stack
at runtime here.
This just shuts up the warning by disabling the warning flag for this
file.
Tested on Nexus 7 2012 builds.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a6430ab9c upstream.
Commit ca6bfcb2f6 ("libata: Enable queued TRIM for Samsung SSD 860")
limited the existing ATA_HORKAGE_NO_NCQ_TRIM quirk from "Samsung SSD 8*",
covering all Samsung 800 series SSDs, to only apply to "Samsung SSD 840*"
and "Samsung SSD 850*" series based on information from Samsung.
But there is a large number of users which is still reporting issues
with the Samsung 860 and 870 SSDs combined with Intel, ASmedia or
Marvell SATA controllers and all reporters also report these problems
going away when disabling queued trims.
Note that with AMD SATA controllers users are reporting even worse
issues and only completely disabling NCQ helps there, this will be
addressed in a separate patch.
Fixes: ca6bfcb2f6 ("libata: Enable queued TRIM for Samsung SSD 860")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=203475
Cc: stable@vger.kernel.org
Cc: Kate Hsuan <hpa@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20210823095220.30157-1-hdegoede@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c1dc8bda3 upstream.
When the ESTABLISH ccw does not complete within the specified timeout,
try our best to cancel the ccw program that is still active on the
device. Otherwise the IO subsystem might be accessing it even after
the driver eg. called qdio_free().
Fixes: 779e6e1c72 ("[S390] qdio: new qdio driver.")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Cc: <stable@vger.kernel.org> # 2.6.27
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c197870e4 upstream.
When qdio_establish() times out while waiting for the ESTABLISH ccw to
complete, it calls qdio_shutdown() to roll back all of its previous
actions. But at this point the qdio_irq's state is still
QDIO_IRQ_STATE_INACTIVE, so qdio_shutdown() will exit immediately
without doing any actual work.
Which means that eg. the qdio_irq's thinint-indicator stays registered,
and cdev->handler isn't restored to its old value. And since
commit 954d6235be ("s390/qdio: make thinint registration symmetric")
the qdio_irq also stays on the tiq_list, so on the next qdio_establish()
we might get a helpful BUG from the list-debugging code:
...
[ 4633.512591] list_add double add: new=00000000005a4110, prev=00000001b357db78, next=00000000005a4110.
[ 4633.512621] ------------[ cut here ]------------
[ 4633.512623] kernel BUG at lib/list_debug.c:29!
...
[ 4633.512796] [<00000001b2c6ee9a>] __list_add_valid+0x82/0xa0
[ 4633.512798] ([<00000001b2c6ee96>] __list_add_valid+0x7e/0xa0)
[ 4633.512800] [<00000001b2fcecce>] qdio_establish_thinint+0x116/0x190
[ 4633.512805] [<00000001b2fcbe58>] qdio_establish+0x128/0x498
...
Fix this by extracting a goto-chain from the existing error exits in
qdio_establish(), and check the return value of the wait_event_...()
to detect the timeout condition.
Fixes: 779e6e1c72 ("[S390] qdio: new qdio driver.")
Root-caused-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Cc: <stable@vger.kernel.org> # 2.6.27
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a10d7fdb6 upstream.
As warned by smatch:
drivers/media/usb/uvc/uvc_v4l2.c:911 uvc_ioctl_g_input() error: doing dma on the stack (&i)
drivers/media/usb/uvc/uvc_v4l2.c:943 uvc_ioctl_s_input() error: doing dma on the stack (&i)
those two functions call uvc_query_ctrl passing a pointer to
a data at the DMA stack. those are used to send URBs via
usb_control_msg(). Using DMA stack is not supported and should
not work anymore on modern Linux versions.
So, use a kmalloc'ed buffer.
Cc: stable@vger.kernel.org # Kernel 4.9 and upper
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a30dc6cf0d upstream.
I got a NULL pointer dereference report when doing fuzz test:
Call Trace:
qp_release_pages+0xae/0x130
qp_host_unregister_user_memory.isra.25+0x2d/0x80
vmci_qp_broker_unmap+0x191/0x320
? vmci_host_do_alloc_queuepair.isra.9+0x1c0/0x1c0
vmci_host_unlocked_ioctl+0x59f/0xd50
? do_vfs_ioctl+0x14b/0xa10
? tomoyo_file_ioctl+0x28/0x30
? vmci_host_do_alloc_queuepair.isra.9+0x1c0/0x1c0
__x64_sys_ioctl+0xea/0x120
do_syscall_64+0x34/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
When a queue pair is created by the following call, it will not
register the user memory if the page_store is NULL, and the
entry->state will be set to VMCIQPB_CREATED_NO_MEM.
vmci_host_unlocked_ioctl
vmci_host_do_alloc_queuepair
vmci_qp_broker_alloc
qp_broker_alloc
qp_broker_create // set entry->state = VMCIQPB_CREATED_NO_MEM;
When unmapping this queue pair, qp_host_unregister_user_memory() will
be called to unregister the non-existent user memory, which will
result in a null pointer reference. It will also change
VMCIQPB_CREATED_NO_MEM to VMCIQPB_CREATED_MEM, which should not be
present in this operation.
Only when the qp broker has mem, it can unregister the user
memory when unmapping the qp broker.
Only when the qp broker has no mem, it can register the user
memory when mapping the qp broker.
Fixes: 06164d2b72 ("VMCI: queue pairs implementation.")
Cc: stable <stable@vger.kernel.org>
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Link: https://lore.kernel.org/r/20210818124845.488312-1-wanghai38@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5441a07a12 upstream.
The commit 97f9ac3db6 ("crypto: ccp - Add support for SEV-ES to the
PSP driver") added support to allocate Trusted Memory Region (TMR)
used during the SEV-ES firmware initialization. The TMR gets locked
during the firmware initialization and unlocked during the shutdown.
While the TMR is locked, access to it is disallowed.
Currently, the CCP driver does not shutdown the firmware during the
kexec reboot, leaving the TMR memory locked.
Register a callback to shutdown the SEV firmware on the kexec boot.
Fixes: 97f9ac3db6 ("crypto: ccp - Add support for SEV-ES to the PSP driver")
Reported-by: Lucas Nussbaum <lucas.nussbaum@inria.fr>
Tested-by: Lucas Nussbaum <lucas.nussbaum@inria.fr>
Cc: <stable@kernel.org>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 528b16bfc3 upstream.
On systems with many cores using dm-crypt, heavy spinlock contention in
percpu_counter_compare() can be observed when the page allocation limit
for a given device is reached or close to be reached. This is due
to percpu_counter_compare() taking a spinlock to compute an exact
result on potentially many CPUs at the same time.
Switch to non-exact comparison of allocated and allowed pages by using
the value returned by percpu_counter_read_positive() to avoid taking
the percpu_counter spinlock.
This may over/under estimate the actual number of allocated pages by at
most (batch-1) * num_online_cpus().
Currently, batch is bounded by 32. The system on which this issue was
first observed has 256 CPUs and 512GB of RAM. With a 4k page size, this
change may over/under estimate by 31MB. With ~10G (2%) allowed dm-crypt
allocations, this seems an acceptable error. Certainly preferred over
running into the spinlock contention.
This behavior was reproduced on an EC2 c5.24xlarge instance with 96 CPUs
and 192GB RAM as follows, but can be provoked on systems with less CPUs
as well.
* Disable swap
* Tune vm settings to promote regular writeback
$ echo 50 > /proc/sys/vm/dirty_expire_centisecs
$ echo 25 > /proc/sys/vm/dirty_writeback_centisecs
$ echo $((128 * 1024 * 1024)) > /proc/sys/vm/dirty_background_bytes
* Create 8 dmcrypt devices based on files on a tmpfs
* Create and mount an ext4 filesystem on each crypt devices
* Run stress-ng --hdd 8 within one of above filesystems
Total %system usage collected from sysstat goes to ~35%. Write throughput
on the underlying loop device is ~2GB/s. perf profiling an individual
kworker kcryptd thread shows the following profile, indicating spinlock
contention in percpu_counter_compare():
99.98% 0.00% kworker/u193:46 [kernel.kallsyms] [k] ret_from_fork
|
--ret_from_fork
kthread
worker_thread
|
--99.92%--process_one_work
|
|--80.52%--kcryptd_crypt
| |
| |--62.58%--mempool_alloc
| | |
| | --62.24%--crypt_page_alloc
| | |
| | --61.51%--__percpu_counter_compare
| | |
| | --61.34%--__percpu_counter_sum
| | |
| | |--58.68%--_raw_spin_lock_irqsave
| | | |
| | | --58.30%--native_queued_spin_lock_slowpath
| | |
| | --0.69%--cpumask_next
| | |
| | --0.51%--_find_next_bit
| |
| |--10.61%--crypt_convert
| | |
| | |--6.05%--xts_crypt
...
After applying this patch and running the same test, %system usage is
lowered to ~7% and write throughput on the loop device increases
to ~2.7GB/s. perf report shows mempool_alloc() as ~8% rather than ~62%
in the profile and not hitting the percpu_counter() spinlock anymore.
|--8.15%--mempool_alloc
| |
| |--3.93%--crypt_page_alloc
| | |
| | --3.75%--__alloc_pages
| | |
| | --3.62%--get_page_from_freelist
| | |
| | --3.22%--rmqueue_bulk
| | |
| | --2.59%--_raw_spin_lock
| | |
| | --2.57%--native_queued_spin_lock_slowpath
| |
| --3.05%--_raw_spin_lock_irqsave
| |
| --2.49%--native_queued_spin_lock_slowpath
Suggested-by: DJ Gregor <dj@corelight.com>
Reviewed-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Arne Welzel <arne.welzel@corelight.com>
Fixes: 5059353df8 ("dm crypt: limit the number of allocated pages")
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54784ffa5b upstream.
Reading status register can fail in the interrupt handler. In such
case, the regmap_read() will not store anything useful under passed
'val' variable and random stack value will be used to determine type of
interrupt.
Handle the regmap_read() failure to avoid handling interrupt type and
triggering changed power supply event based on random stack value.
Fixes: 39e7213edc ("max17042_battery: Support regmap to access device's registers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a680dd72ec upstream.
For a request that has a priority level equal to or larger than
IOPRIO_BE_NR, bfq_set_next_ioprio_data() prints a critical warning but
defaults to setting the request new_ioprio field to IOPRIO_BE_NR. This
is not consistent with the warning and the allowed values for priority
levels. Fix this by setting the request new_ioprio field to
IOPRIO_BE_NR - 1, the lowest priority level allowed.
Cc: <stable@vger.kernel.org>
Fixes: aee69d78de ("block, bfq: introduce the BFQ-v0 I/O scheduler as an extra scheduler")
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20210811033702.368488-2-damien.lemoal@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b76d26d69e upstream.
There is no reason to assume that the IRQ rising edge (indicating that
the device start up phase is done) will happen after we request the IRQ.
If the device is already up by the time we request it, the call to
'wait_for_completion_timeout()' will timeout and we will fail the device
probe even though there's nothing wrong.
Fix it by just polling the status register until we get the indication that
the device is up and running. As a side effect of this fix, requesting the
IRQ is also moved to after the setup function.
Fixes: f110f3188e ("iio: temperature: Add support for LTC2983")
Reported-and-tested-by: Drew Fustini <drew@pdp7.com>
Reviewed-by: Drew Fustini <drew@pdp7.com>
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210811133220.190264-2-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90268574a3 upstream.
The `compute_indices` and `populate_entries` macros operate on inclusive
bounds, and thus the `map_memory` macro which uses them also operates
on inclusive bounds.
We pass `_end` and `_idmap_text_end` to `map_memory`, but these are
exclusive bounds, and if one of these is sufficiently aligned (as a
result of kernel configuration, physical placement, and KASLR), then:
* In `compute_indices`, the computed `iend` will be in the page/block *after*
the final byte of the intended mapping.
* In `populate_entries`, an unnecessary entry will be created at the end
of each level of table. At the leaf level, this entry will map up to
SWAPPER_BLOCK_SIZE bytes of physical addresses that we did not intend
to map.
As we may map up to SWAPPER_BLOCK_SIZE bytes more than intended, we may
violate the boot protocol and map physical address past the 2MiB-aligned
end address we are permitted to map. As we map these with Normal memory
attributes, this may result in further problems depending on what these
physical addresses correspond to.
The final entry at each level may require an additional table at that
level. As EARLY_ENTRIES() calculates an inclusive bound, we allocate
enough memory for this.
Avoid the extraneous mapping by having map_memory convert the exclusive
end address to an inclusive end address by subtracting one, and do
likewise in EARLY_ENTRIES() when calculating the number of required
tables. For clarity, comments are updated to more clearly document which
boundaries the macros operate on. For consistency with the other
macros, the comments in map_memory are also updated to describe `vstart`
and `vend` as virtual addresses.
Fixes: 0370b31e48 ("arm64: Extend early page table code to allow for larger kernels")
Cc: <stable@vger.kernel.org> # 4.16.x
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Steve Capper <steve.capper@arm.com>
Cc: Will Deacon <will@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210823101253.55567-1-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e10f9887e upstream.
When switching to an 'mm_struct' for the first time following an ASID
rollover, a new ASID may be allocated and assigned to 'mm->context.id'.
This reassignment can happen concurrently with other operations on the
mm, such as unmapping pages and subsequently issuing TLB invalidation.
Consequently, we need to ensure that (a) accesses to 'mm->context.id'
are atomic and (b) all page-table updates made prior to a TLBI using the
old ASID are guaranteed to be visible to CPUs running with the new ASID.
This was found by inspection after reviewing the VMID changes from
Shameer but it looks like a real (yet hard to hit) bug.
Cc: <stable@vger.kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Jade Alglave <jade.alglave@arm.com>
Cc: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Signed-off-by: Will Deacon <will@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20210806113109.2475-2-will@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b07e990fb upstream.
The check mixes pages (vm_pgoff) with bytes (vm_start, vm_end) on one
side of the comparison, and uses resource address (rather than just the
resource size) on the other side of the comparison.
This can allow malicious userspace to easily bypass the boundary check and
map pages that are located outside memory-region reserved by the driver.
Fixes: 01c60dcea9 ("drivers/misc: Add Aspeed P2A control driver")
Cc: stable@vger.kernel.org
Signed-off-by: Iwona Winiarska <iwona.winiarska@intel.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Tested-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b49a0e69a7 upstream.
The check mixes pages (vm_pgoff) with bytes (vm_start, vm_end) on one
side of the comparison, and uses resource address (rather than just the
resource size) on the other side of the comparison.
This can allow malicious userspace to easily bypass the boundary check and
map pages that are located outside memory-region reserved by the driver.
Fixes: 6c4e976785 ("drivers/misc: Add Aspeed LPC control driver")
Cc: stable@vger.kernel.org
Signed-off-by: Iwona Winiarska <iwona.winiarska@intel.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Tested-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a89f355e46 upstream.
In "qmp_cooling_devices_register", the count value is initially
QMP_NUM_COOLING_RESOURCES, which is 2. Based on the initial count value,
the memory for cooling_devs is allocated. Then while calling the
"qmp_cooling_device_add" function, count value is post-incremented for
each child node.
This makes the out of bound access to the cooling_dev array. Fix it by
passing the QMP_NUM_COOLING_RESOURCES definition to devm_kzalloc() and
initializing the count to 0.
While at it, let's also free the memory allocated to cooling_dev if no
cooling device is found in DT and during unroll phase.
Cc: stable@vger.kernel.org # 5.4
Fixes: 05589b30b2 ("soc: qcom: Extend AOSS QMP driver to support resources that are used to wake up the SoC.")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210629153249.73428-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05a444d3f9 upstream.
Currently in the case where kmem_cache_alloc fails the null pointer
cf is dereferenced when assigning cf->is_capsnap = false. Fix this
by adding a null pointer check and return path.
Cc: stable@vger.kernel.org
Addresses-Coverity: ("Dereference null return")
Fixes: b2f9fa1f3b ("ceph: correctly handle releasing an embedded cap flush")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b511d5bfa upstream.
Xen PV guests are specifying the highest used PFN via the max_pfn
field in shared_info. This value is used by the Xen tools when saving
or migrating the guest.
Unfortunately this field is misnamed, as in reality it is specifying
the number of pages (including any memory holes) of the guest, so it
is the highest used PFN + 1. Renaming isn't possible, as this is a
public Xen hypervisor interface which needs to be kept stable.
The kernel will set the value correctly initially at boot time, but
when adding more pages (e.g. due to memory hotplug or ballooning) a
real PFN number is stored in max_pfn. This is done when expanding the
p2m array, and the PFN stored there is even possibly wrong, as it
should be the last possible PFN of the just added P2M frame, and not
one which led to the P2M expansion.
Fix that by setting shared_info->max_pfn to the last possible PFN + 1.
Fixes: 98dd166ea3 ("x86/xen/p2m: hint at the last populated P2M entry")
Cc: stable@vger.kernel.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Link: https://lore.kernel.org/r/20210730092622.9973-2-jgross@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9addd85fb upstream.
H_GetPerformanceCounterInfo (0xF080) hcall returns the counter data in
the result buffer. Result buffer has specific format defined in the PAPR
specification. One of the fields is counter offset and width of the
counter data returned.
Counter data are returned in a unsigned char array in big endian byte
order. To get the final counter data, the values must be left shifted
byte at a time. But commit 220a0c609a ("powerpc/perf: Add support for
the hv gpci (get performance counter info) interface") made the shifting
bitwise and also assumed little endian order. Because of that, hcall
counters values are reported incorrectly.
In particular this can lead to counters go backwards which messes up the
counter prev vs now calculation and leads to huge counter value
reporting:
#: perf stat -e hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
-C 0 -I 1000
time counts unit events
1.000078854 18,446,744,073,709,535,232 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
2.000213293 0 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
3.000320107 0 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
4.000428392 0 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
5.000537864 0 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
6.000649087 0 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
7.000760312 0 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
8.000865218 16,448 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
9.000978985 18,446,744,073,709,535,232 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
10.001088891 16,384 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
11.001201435 0 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
12.001307937 18,446,744,073,709,535,232 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
Fix the shifting logic to correct match the format, ie. read bytes in
big endian order.
Fixes: e4f226b158 ("powerpc/perf/hv-gpci: Increase request buffer size")
Cc: stable@vger.kernel.org # v4.6+
Reported-by: Nageswara R Sastry<rnsastry@linux.ibm.com>
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
Tested-by: Nageswara R Sastry<rnsastry@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210813082158.429023-1-kjain@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a519dc7a7 upstream.
When running as Xen PV guest, masking MSI-X is a responsibility of the
hypervisor. The guest has no write access to the relevant BAR at all - when
it tries to, it results in a crash like this:
BUG: unable to handle page fault for address: ffffc9004069100c
#PF: supervisor write access in kernel mode
#PF: error_code(0x0003) - permissions violation
RIP: e030:__pci_enable_msix_range.part.0+0x26b/0x5f0
e1000e_set_interrupt_capability+0xbf/0xd0 [e1000e]
e1000_probe+0x41f/0xdb0 [e1000e]
local_pci_probe+0x42/0x80
(...)
The recently introduced function msix_mask_all() does not check the global
variable pci_msi_ignore_mask which is set by XEN PV to bypass the masking
of MSI[-X] interrupts.
Add the check to make this function XEN PV compatible.
Fixes: 7d5ec3d361 ("PCI/MSI: Mask all unused MSI-X entries")
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210826170342.135172-1-marmarek@invisiblethingslab.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ead3b768bb upstream.
Zone management send operations (BLKRESETZONE, BLKOPENZONE, BLKCLOSEZONE
and BLKFINISHZONE) should be allowed under the same permissions as write().
(write() does not require CAP_SYS_ADMIN).
Additionally, other ioctls like BLKSECDISCARD and BLKZEROOUT only check if
the fd was successfully opened with FMODE_WRITE.
(They do not require CAP_SYS_ADMIN).
Currently, zone management send operations require both CAP_SYS_ADMIN
and that the fd was successfully opened with FMODE_WRITE.
Remove the CAP_SYS_ADMIN requirement, so that zone management send
operations match the access control requirement of write(), BLKSECDISCARD
and BLKZEROOUT.
Fixes: 3ed05a987e ("blk-zoned: implement ioctls")
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Aravind Ramesh <aravind.ramesh@wdc.com>
Reviewed-by: Adam Manzanares <a.manzanares@samsung.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Cc: stable@vger.kernel.org # v4.10+
Link: https://lore.kernel.org/r/20210811110505.29649-2-Niklas.Cassel@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d977e0eba upstream.
This crash was observed with a failed assertion on device close:
BTRFS: Transaction aborted (error -28)
WARNING: CPU: 1 PID: 3902 at fs/btrfs/extent-tree.c:2150 btrfs_run_delayed_refs+0x1d2/0x1e0 [btrfs]
Modules linked in: btrfs blake2b_generic libcrc32c crc32c_intel xor zstd_decompress zstd_compress xxhash lzo_compress lzo_decompress raid6_pq loop
CPU: 1 PID: 3902 Comm: kworker/u8:4 Not tainted 5.14.0-rc5-default+ #1532
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-59-gc9ba527-rebuilt.opensuse.org 04/01/2014
Workqueue: events_unbound btrfs_async_reclaim_metadata_space [btrfs]
RIP: 0010:btrfs_run_delayed_refs+0x1d2/0x1e0 [btrfs]
RSP: 0018:ffffb7a5452d7d80 EFLAGS: 00010282
RAX: 0000000000000000 RBX: 0000000000000003 RCX: 0000000000000000
RDX: 0000000000000001 RSI: ffffffffabee13c4 RDI: 00000000ffffffff
RBP: ffff97834176a378 R08: 0000000000000001 R09: 0000000000000001
R10: 0000000000000000 R11: 0000000000000001 R12: ffff97835195d388
R13: 0000000005b08000 R14: ffff978385484000 R15: 000000000000016c
FS: 0000000000000000(0000) GS:ffff9783bd800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000056190d003fe8 CR3: 000000002a81e005 CR4: 0000000000170ea0
Call Trace:
flush_space+0x197/0x2f0 [btrfs]
btrfs_async_reclaim_metadata_space+0x139/0x300 [btrfs]
process_one_work+0x262/0x5e0
worker_thread+0x4c/0x320
? process_one_work+0x5e0/0x5e0
kthread+0x144/0x170
? set_kthread_struct+0x40/0x40
ret_from_fork+0x1f/0x30
irq event stamp: 19334989
hardirqs last enabled at (19334997): [<ffffffffab0e0c87>] console_unlock+0x2b7/0x400
hardirqs last disabled at (19335006): [<ffffffffab0e0d0d>] console_unlock+0x33d/0x400
softirqs last enabled at (19334900): [<ffffffffaba0030d>] __do_softirq+0x30d/0x574
softirqs last disabled at (19334893): [<ffffffffab0721ec>] irq_exit_rcu+0x12c/0x140
---[ end trace 45939e308e0dd3c7 ]---
BTRFS: error (device vdd) in btrfs_run_delayed_refs:2150: errno=-28 No space left
BTRFS info (device vdd): forced readonly
BTRFS warning (device vdd): failed setting block group ro: -30
BTRFS info (device vdd): suspending dev_replace for unmount
assertion failed: !test_bit(BTRFS_DEV_STATE_REPLACE_TGT, &device->dev_state), in fs/btrfs/volumes.c:1150
------------[ cut here ]------------
kernel BUG at fs/btrfs/ctree.h:3431!
invalid opcode: 0000 [#1] PREEMPT SMP
CPU: 1 PID: 3982 Comm: umount Tainted: G W 5.14.0-rc5-default+ #1532
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-59-gc9ba527-rebuilt.opensuse.org 04/01/2014
RIP: 0010:assertfail.constprop.0+0x18/0x1a [btrfs]
RSP: 0018:ffffb7a5454c7db8 EFLAGS: 00010246
RAX: 0000000000000068 RBX: ffff978364b91c00 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffffffabee13c4 RDI: 00000000ffffffff
RBP: ffff9783523a4c00 R08: 0000000000000001 R09: 0000000000000001
R10: 0000000000000000 R11: 0000000000000001 R12: ffff9783523a4d18
R13: 0000000000000000 R14: 0000000000000004 R15: 0000000000000003
FS: 00007f61c8f42800(0000) GS:ffff9783bd800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000056190cffa810 CR3: 0000000030b96002 CR4: 0000000000170ea0
Call Trace:
btrfs_close_one_device.cold+0x11/0x55 [btrfs]
close_fs_devices+0x44/0xb0 [btrfs]
btrfs_close_devices+0x48/0x160 [btrfs]
generic_shutdown_super+0x69/0x100
kill_anon_super+0x14/0x30
btrfs_kill_super+0x12/0x20 [btrfs]
deactivate_locked_super+0x2c/0xa0
cleanup_mnt+0x144/0x1b0
task_work_run+0x59/0xa0
exit_to_user_mode_loop+0xe7/0xf0
exit_to_user_mode_prepare+0xaf/0xf0
syscall_exit_to_user_mode+0x19/0x50
do_syscall_64+0x4a/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
This happens when close_ctree is called while a dev_replace hasn't
completed. In close_ctree, we suspend the dev_replace, but keep the
replace target around so that we can resume the dev_replace procedure
when we mount the root again. This is the call trace:
close_ctree():
btrfs_dev_replace_suspend_for_unmount();
btrfs_close_devices():
btrfs_close_fs_devices():
btrfs_close_one_device():
ASSERT(!test_bit(BTRFS_DEV_STATE_REPLACE_TGT,
&device->dev_state));
However, since the replace target sticks around, there is a device
with BTRFS_DEV_STATE_REPLACE_TGT set on close, and we fail the
assertion in btrfs_close_one_device.
To fix this, if we come across the replace target device when
closing, we should properly reset it back to allocation state. This
fix also ensures that if a non-target device has a corrupted state and
has the BTRFS_DEV_STATE_REPLACE_TGT bit set, the assertion will still
catch the error.
Reported-by: David Sterba <dsterba@suse.com>
Fixes: b2a6166768 ("btrfs: fix rw device counting in __btrfs_free_extra_devids")
CC: stable@vger.kernel.org # 4.19+
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac98141d14 upstream.
We use the async_delalloc_pages mechanism to make sure that we've
completed our async work before trying to continue our delalloc
flushing. The reason for this is we need to see any ordered extents
that were created by our delalloc flushing. However we're waking up
before we do the submit work, which is before we create the ordered
extents. This is a pretty wide race window where we could potentially
think there are no ordered extents and thus exit shrink_delalloc
prematurely. Fix this by waking us up after we've done the work to
create ordered extents.
CC: stable@vger.kernel.org # 5.4+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87df7fb922 upstream.
When new work is added, io_wqe_enqueue() checks if we need to wake or
create a new worker. But that check is done outside the lock that
otherwise synchronizes us with a worker going to sleep, so we can end
up in the following situation:
CPU0 CPU1
lock
insert work
unlock
atomic_read(nr_running) != 0
lock
atomic_dec(nr_running)
no wakeup needed
Hold the wqe lock around the "need to wakeup" check. Then we can also get
rid of the temporary work_flags variable, as we know the work will remain
valid as long as we hold the lock.
Cc: stable@vger.kernel.org
Reported-by: Andres Freund <andres@anarazel.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 4711284768.
Botched backport, dropping to rework for next release.
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit aaedb9e00e upstream.
Since a few kernel releases the Pogoplug 4 has crashed like this
during boot:
Unable to handle kernel NULL pointer dereference at virtual address 00000002
(...)
[<c04116ec>] (strlen) from [<c00ead80>] (kstrdup+0x1c/0x4c)
[<c00ead80>] (kstrdup) from [<c04591d8>] (__clk_register+0x44/0x37c)
[<c04591d8>] (__clk_register) from [<c04595ec>] (clk_hw_register+0x20/0x44)
[<c04595ec>] (clk_hw_register) from [<c045bfa8>] (__clk_hw_register_mux+0x198/0x1e4)
[<c045bfa8>] (__clk_hw_register_mux) from [<c045c050>] (clk_register_mux_table+0x5c/0x6c)
[<c045c050>] (clk_register_mux_table) from [<c0acf3e0>] (kirkwood_clk_muxing_setup.constprop.0+0x13c/0x1ac)
[<c0acf3e0>] (kirkwood_clk_muxing_setup.constprop.0) from [<c0aceae0>] (of_clk_init+0x12c/0x214)
[<c0aceae0>] (of_clk_init) from [<c0ab576c>] (time_init+0x20/0x2c)
[<c0ab576c>] (time_init) from [<c0ab3d18>] (start_kernel+0x3dc/0x56c)
[<c0ab3d18>] (start_kernel) from [<00000000>] (0x0)
Code: e3130020 1afffffb e12fff1e c08a1078 (e5d03000)
This is because the "powersave" mux clock 0 was provided in an unterminated
array, which is required by the loop in the driver:
/* Count, allocate, and register clock muxes */
for (n = 0; desc[n].name;)
n++;
Here n will go out of bounds and then call clk_register_mux() on random
memory contents after the mux clock.
Fix this by terminating the array with a blank entry.
Fixes: 105299381d ("cpufreq: kirkwood: use the powersave multiplexer")
Cc: stable@vger.kernel.org
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210814235514.403426-1-linus.walleij@linaro.org
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 79fad92f2e upstream.
Currently there are (at least) two problems in the way pwm_bl starts
managing the enable_gpio pin. Both occur when the backlight is initially
off and the driver finds the pin not already in output mode and, as a
result, unconditionally switches it to output-mode and asserts the signal.
Problem 1: This could cause the backlight to flicker since, at this stage
in driver initialisation, we have no idea what the PWM and regulator are
doing (an unconfigured PWM could easily "rest" at 100% duty cycle).
Problem 2: This will cause us not to correctly honour the
post_pwm_on_delay (which also risks flickers).
Fix this by moving the code to configure the GPIO output mode until after
we have examines the handover state. That allows us to initialize
enable_gpio to off if the backlight is currently off and on if the
backlight is on.
Cc: stable@vger.kernel.org
Reported-by: Marek Vasut <marex@denx.de>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8510505d55 upstream.
MD5 is a weak digest algorithm that shouldn't be used for cryptographic
operation. It hinders the efficiency of a patch set that aims to limit
the digests allowed for the extended file attribute namely security.ima.
MD5 is no longer a requirement for IMA, nor should it be used there.
The sole place where we still use the MD5 algorithm inside IMA is setting
the ima_hash algorithm to MD5, if the user supplies 'ima_hash=md5'
parameter on the command line. With commit ab60368ab6 ("ima: Fallback
to the builtin hash algorithm"), setting "ima_hash=md5" fails gracefully
when CRYPTO_MD5 is not set:
ima: Can not allocate md5 (reason: -2)
ima: Allocating md5 failed, going to use default hash algorithm sha256
Remove the CRYPTO_MD5 dependency for IMA.
Signed-off-by: THOBY Simon <Simon.THOBY@viveris.fr>
Reviewed-by: Lakshmi Ramasubramanian <nramas@linux.microsoft.com>
[zohar@linux.ibm.com: include commit number in patch description for
stable.]
Cc: stable@vger.kernel.org # 4.17
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 59bda8ecee upstream.
Callers of fuse_writeback_range() assume that the file is ready for
modification by the server in the supplied byte range after the call
returns.
If there's a write that extends the file beyond the end of the supplied
range, then the file needs to be extended to at least the end of the range,
but currently that's not done.
There are at least two cases where this can cause problems:
- copy_file_range() will return short count if the file is not extended
up to end of the source range.
- FALLOC_FL_ZERO_RANGE | FALLOC_FL_KEEP_SIZE will not extend the file,
hence the region may not be fully allocated.
Fix by flushing writes from the start of the range up to the end of the
file. This could be optimized if the writes are non-extending, etc, but
it's probably not worth the trouble.
Fixes: a2bc923629 ("fuse: fix copy_file_range() in the writeback case")
Fixes: 6b1bdb56b1 ("fuse: allow fallocate(FALLOC_FL_ZERO_RANGE)")
Cc: <stable@vger.kernel.org> # v5.2
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 76224355db upstream.
fuse_finish_open() will be called with FUSE_NOWRITE in case of atomic
O_TRUNC. This can deadlock with fuse_wait_on_page_writeback() in
fuse_launder_page() triggered by invalidate_inode_pages2().
Fix by replacing invalidate_inode_pages2() in fuse_finish_open() with a
truncate_pagecache() call. This makes sense regardless of FOPEN_KEEP_CACHE
or fc->writeback cache, so do it unconditionally.
Reported-by: Xie Yongji <xieyongji@bytedance.com>
Reported-and-tested-by: syzbot+bea44a5189836d956894@syzkaller.appspotmail.com
Fixes: e4648309b8 ("fuse: truncate pending writes on O_TRUNC")
Cc: <stable@vger.kernel.org>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7782bb8d8 upstream.
Clear nested.pi_pending on nested VM-Enter even if L2 will run without
posted interrupts enabled. If nested.pi_pending is left set from a
previous L2, vmx_complete_nested_posted_interrupt() will pick up the
stale flag and exit to userspace with an "internal emulation error" due
the new L2 not having a valid nested.pi_desc.
Arguably, vmx_complete_nested_posted_interrupt() should first check for
posted interrupts being enabled, but it's also completely reasonable that
KVM wouldn't screw up a fundamental flag. Not to mention that the mere
existence of nested.pi_pending is a long-standing bug as KVM shouldn't
move the posted interrupt out of the IRR until it's actually processed,
e.g. KVM effectively drops an interrupt when it performs a nested VM-Exit
with a "pending" posted interrupt. Fixing the mess is a future problem.
Prior to vmx_complete_nested_posted_interrupt() interpreting a null PI
descriptor as an error, this was a benign bug as the null PI descriptor
effectively served as a check on PI not being enabled. Even then, the
new flow did not become problematic until KVM started checking the result
of kvm_check_nested_events().
Fixes: 705699a139 ("KVM: nVMX: Enable nested posted interrupt processing")
Fixes: 966eefb896 ("KVM: nVMX: Disable vmcs02 posted interrupts if vmcs12 PID isn't mappable")
Fixes: 47d3530f86c0 ("KVM: x86: Exit to userspace when kvm_check_nested_events fails")
Cc: stable@vger.kernel.org
Cc: Jim Mattson <jmattson@google.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210810144526.2662272-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9130a2dfd upstream.
When MSR_IA32_TSC_ADJUST is written by guest due to TSC ADJUST feature
especially there's a big tsc warp (like a new vCPU is hot-added into VM
which has been up for a long time), tsc_offset is added by a large value
then go back to guest. This causes system time jump as tsc_timestamp is
not adjusted in the meantime and pvclock monotonic character.
To fix this, just notify kvm to update vCPU's guest time before back to
guest.
Cc: stable@vger.kernel.org
Signed-off-by: Zelin Deng <zelin.deng@linux.alibaba.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1619576521-81399-2-git-send-email-zelin.deng@linux.alibaba.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a3e03bc136 upstream.
While in practice vcpu->vcpu_idx == vcpu->vcp_id is often true, it may
not always be, and we must not rely on this. Reason is that KVM decides
the vcpu_idx, userspace decides the vcpu_id, thus the two might not
match.
Currently kvm->arch.idle_mask is indexed by vcpu_id, which implies
that code like
for_each_set_bit(vcpu_id, kvm->arch.idle_mask, online_vcpus) {
vcpu = kvm_get_vcpu(kvm, vcpu_id);
do_stuff(vcpu);
}
is not legit. Reason is that kvm_get_vcpu expects an vcpu_idx, not an
vcpu_id. The trouble is, we do actually use kvm->arch.idle_mask like
this. To fix this problem we have two options. Either use
kvm_get_vcpu_by_id(vcpu_id), which would loop to find the right vcpu_id,
or switch to indexing via vcpu_idx. The latter is preferable for obvious
reasons.
Let us make switch from indexing kvm->arch.idle_mask by vcpu_id to
indexing it by vcpu_idx. To keep gisa_int.kicked_mask indexed by the
same index as idle_mask lets make the same change for it as well.
Fixes: 1ee0bc559d ("KVM: s390: get rid of local_int array")
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Christian Bornträger <borntraeger@de.ibm.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Cc: <stable@vger.kernel.org> # 3.15+
Link: https://lore.kernel.org/r/20210827125429.1912577-1-pasic@linux.ibm.com
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7177339d7 upstream.
Revert a misguided illegal GPA check when "translating" a non-nested GPA.
The check is woefully incomplete as it does not fill in @exception as
expected by all callers, which leads to KVM attempting to inject a bogus
exception, potentially exposing kernel stack information in the process.
WARNING: CPU: 0 PID: 8469 at arch/x86/kvm/x86.c:525 exception_type+0x98/0xb0 arch/x86/kvm/x86.c:525
CPU: 1 PID: 8469 Comm: syz-executor531 Not tainted 5.14.0-rc7-syzkaller #0
RIP: 0010:exception_type+0x98/0xb0 arch/x86/kvm/x86.c:525
Call Trace:
x86_emulate_instruction+0xef6/0x1460 arch/x86/kvm/x86.c:7853
kvm_mmu_page_fault+0x2f0/0x1810 arch/x86/kvm/mmu/mmu.c:5199
handle_ept_misconfig+0xdf/0x3e0 arch/x86/kvm/vmx/vmx.c:5336
__vmx_handle_exit arch/x86/kvm/vmx/vmx.c:6021 [inline]
vmx_handle_exit+0x336/0x1800 arch/x86/kvm/vmx/vmx.c:6038
vcpu_enter_guest+0x2a1c/0x4430 arch/x86/kvm/x86.c:9712
vcpu_run arch/x86/kvm/x86.c:9779 [inline]
kvm_arch_vcpu_ioctl_run+0x47d/0x1b20 arch/x86/kvm/x86.c:10010
kvm_vcpu_ioctl+0x49e/0xe50 arch/x86/kvm/../../../virt/kvm/kvm_main.c:3652
The bug has escaped notice because practically speaking the GPA check is
useless. The GPA check in question only comes into play when KVM is
walking guest page tables (or "translating" CR3), and KVM already handles
illegal GPA checks by setting reserved bits in rsvd_bits_mask for each
PxE, or in the case of CR3 for loading PTDPTRs, manually checks for an
illegal CR3. This particular failure doesn't hit the existing reserved
bits checks because syzbot sets guest.MAXPHYADDR=1, and IA32 architecture
simply doesn't allow for such an absurd MAXPHYADDR, e.g. 32-bit paging
doesn't define any reserved PA bits checks, which KVM emulates by only
incorporating the reserved PA bits into the "high" bits, i.e. bits 63:32.
Simply remove the bogus check. There is zero meaningful value and no
architectural justification for supporting guest.MAXPHYADDR < 32, and
properly filling the exception would introduce non-trivial complexity.
This reverts commit ec7771ab47.
Fixes: ec7771ab47 ("KVM: x86: mmu: Add guest physical address check in translate_gpa()")
Cc: stable@vger.kernel.org
Reported-by: syzbot+200c08e88ae818f849ce@syzkaller.appspotmail.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210831164224.1119728-2-seanjc@google.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 527f721478 upstream.
The recent commit
064855a690 ("x86/resctrl: Fix default monitoring groups reporting")
caused a RHEL build failure with an uninitialized variable warning
treated as an error because it removed the default case snippet.
The RHEL Makefile uses '-Werror=maybe-uninitialized' to force possibly
uninitialized variable warnings to be treated as errors. This is also
reported by smatch via the 0day robot.
The error from the RHEL build is:
arch/x86/kernel/cpu/resctrl/monitor.c: In function ‘__mon_event_count’:
arch/x86/kernel/cpu/resctrl/monitor.c:261:12: error: ‘m’ may be used
uninitialized in this function [-Werror=maybe-uninitialized]
m->chunks += chunks;
^~
The upstream Makefile does not build using '-Werror=maybe-uninitialized'.
So, the problem is not seen there. Fix the problem by putting back the
default case snippet.
[ bp: note that there's nothing wrong with the code and other compilers
do not trigger this warning - this is being done just so the RHEL compiler
is happy. ]
Fixes: 064855a690 ("x86/resctrl: Fix default monitoring groups reporting")
Reported-by: Terry Bowman <Terry.Bowman@amd.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/162949631908.23903.17090272726012848523.stgit@bmoger-ubuntu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb2853a6a4 upstream.
The ops->receive_buf() may be accessed concurrently from these two
functions. If the driver flushes data to the line discipline
receive_buf() method while tiocsti() is waiting for the
ops->receive_buf() to finish its work, the data race will happen.
For example:
tty_ioctl |tty_ldisc_receive_buf
->tioctsi | ->tty_port_default_receive_buf
| ->tty_ldisc_receive_buf
->hci_uart_tty_receive | ->hci_uart_tty_receive
->h4_recv | ->h4_recv
In this case, the h4 receive buffer will be overwritten by the
latecomer, and we will lost the data.
Hence, change tioctsi() function to use the exclusive lock interface
from tty_buffer to avoid the data race.
Reported-by: syzbot+97388eb9d31b997fe1d0@syzkaller.appspotmail.com
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Nguyen Dinh Phi <phind.uet@gmail.com>
Link: https://lore.kernel.org/r/20210823000641.2082292-1-phind.uet@gmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b3188e7ed upstream.
During some testing, it became evident that using IORING_OP_WRITE doesn't
hash buffered writes like the other writes commands do. That's simply
an oversight, and can cause performance regressions when doing buffered
writes with this command.
Correct that and add the flag, so that buffered writes are correctly
hashed when using the non-iovec based write command.
Cc: stable@vger.kernel.org
Fixes: 3a6820f2bb ("io_uring: add non-vectored read/write commands")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39ff83f2f6 upstream.
timespec64_ns() prevents multiplication overflows by comparing the seconds
value of the timespec to KTIME_SEC_MAX. If the value is greater or equal it
returns KTIME_MAX.
But that check casts the signed seconds value to unsigned which makes the
comparision true for all negative values and therefore return wrongly
KTIME_MAX.
Negative second values are perfectly valid and required in some places,
e.g. ptp_clock_adjtime().
Remove the cast and add a check for the negative boundary which is required
to prevent undefined behaviour due to multiplication underflow.
Fixes: cb47755725 ("time: Prevent undefined behaviour in timespec64_to_ns()")'
Signed-off-by: Lukas Hannen <lukas.hannen@opensource.tttech-industrial.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/AM6PR01MB541637BD6F336B8FFB72AF80EEC69@AM6PR01MB5416.eurprd01.prod.exchangelabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dddd3d6529 upstream.
We must flush all the dirty data when enabling checkpoint back. Let's guarantee
that first by adding a retry logic on sync_inodes_sb(). In addition to that,
this patch adds to flush data in fsync when checkpoint is disabled, which can
mitigate the sync_inodes_sb() failures in advance.
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 92548b0ee2 ]
The UDP length field should be in network order.
This removes the following sparse error:
net/ipv4/route.c:3173:27: warning: incorrect type in assignment (different base types)
net/ipv4/route.c:3173:27: expected restricted __be16 [usertype] len
net/ipv4/route.c:3173:27: got unsigned long
Fixes: 404eb77ea7 ("ipv4: support sport, dport and ip_proto in RTM_GETROUTE")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Roopa Prabhu <roopa@nvidia.com>
Cc: David Ahern <dsahern@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e4428b6db ]
With current config, for packets with IPv4 checksum errors,
errorcode is being set to UNKNOWN. Hence added a separate
errorcodes for outer and inner IPv4 checksum and changed
NPC configuration accordingly.
Also turn on L2 multicast address check in NPC protocol check block.
Fixes: 6b3321bacc ("octeontx2-af: Enable packet length and csum validation")
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 698a82ebfb ]
This patch fixes the static code analyzer reported issues
in rvu_npc.c. The reported errors are different sizes of
operands in bitops and returning uninitialized values.
Fixes: 651cd26523 ("octeontx2-af: MCAM entry installation support")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6537e96d74 ]
When the given counter does not belong to the entry
then code ends up in infinite loop because the loop
cursor, entry is not getting updated further. This
patch fixes that by updating entry for every iteration.
Fixes: a958dd59f9 ("octeontx2-af: Map or unmap NPC MCAM entry and counter")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 429205da6c ]
Based on tests the QCA7000 doesn't support checksum offloading. So assume
ip_summed is CHECKSUM_NONE and let the kernel take care of the checksum
handling. This fixes data transfer issues in noisy environments.
Reported-by: Michael Heimpold <michael.heimpold@in-tech.com>
Fixes: 291ab06ecf ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 67d6d681e1 ]
Even after commit 6457378fe7 ("ipv4: use siphash instead of Jenkins in
fnhe_hashfun()"), an attacker can still use brute force to learn
some secrets from a victim linux host.
One way to defeat these attacks is to make the max depth of the hash
table bucket a random value.
Before this patch, each bucket of the hash table used to store exceptions
could contain 6 items under attack.
After the patch, each bucket would contains a random number of items,
between 6 and 10. The attacker can no longer infer secrets.
This is slightly increasing memory size used by the hash table,
by 50% in average, we do not expect this to be a problem.
This patch is more complex than the prior one (IPv6 equivalent),
because IPv4 was reusing the oldest entry.
Since we need to be able to evict more than one entry per
update_or_create_fnhe() call, I had to replace
fnhe_oldest() with fnhe_remove_oldest().
Also note that we will queue extra kfree_rcu() calls under stress,
which hopefully wont be a too big issue.
Fixes: 4895c771c7 ("ipv4: Add FIB nexthop exceptions.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Keyu Man <kman001@ucr.edu>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reviewed-by: David Ahern <dsahern@kernel.org>
Tested-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a00df2caff ]
Even after commit 4785305c05 ("ipv6: use siphash in rt6_exception_hash()"),
an attacker can still use brute force to learn some secrets from a victim
linux host.
One way to defeat these attacks is to make the max depth of the hash
table bucket a random value.
Before this patch, each bucket of the hash table used to store exceptions
could contain 6 items under attack.
After the patch, each bucket would contains a random number of items,
between 6 and 10. The attacker can no longer infer secrets.
This is slightly increasing memory size used by the hash table,
we do not expect this to be a problem.
Following patch is dealing with the same issue in IPv4.
Fixes: 35732d01fe ("ipv6: introduce a hash table to store dst cache")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Keyu Man <kman001@ucr.edu>
Cc: Wei Wang <weiwan@google.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d745ca4f2c ]
When resuming from suspend, brcmf_pcie_pm_leave_D3 will first attempt a
hot resume and then fall back to removing the PCI device and then
reprobing. If this probe fails, the kernel will oops, because brcmf_err,
which is called to report the failure will dereference the stale bus
pointer. Open code and use the default bus-less brcmf_err to avoid this.
Fixes: 8602e62441 ("brcmfmac: pass bus to the __brcmf_err() in pcie.c")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210817063521.22450-1-a.fatoum@pengutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b63aed3ff1 ]
kmemleak reported that dev_name() of internally-handled cores were leaked
on driver unbinding. Let's use device_initialize() to take refcounts for
them and put_device() to properly free the related stuff.
While looking at it, there's another potential issue for those which should
be *registered* into driver core. If device_register() failed, we put
device once and freed bcma_device structures. In bcma_unregister_cores(),
they're treated as unregistered and we hit both UAF and double-free. That
smells not good and has also been fixed now.
Fixes: ab54bc8460 ("bcma: fill core details for every device")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210727025232.663-2-yuzenghui@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57f780f1c4 ]
Driver crashes when restoring from the Hibernate. In the resume flow,
driver need to clean up the older nic/vec objects and re-initialize them.
Fixes: 8aaa112a57 ("net: atlantic: refactoring pm logic")
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a6a723e98 ]
There is no point in calling 'free_irq()' explicitly for
'WCD9335_IRQ_SLIMBUS' in the remove function.
The irqs are requested in 'wcd9335_setup_irqs()' using a resource managed
function (i.e. 'devm_request_threaded_irq()').
'wcd9335_setup_irqs()' requests all what is defined in the 'wcd9335_irqs'
structure.
This structure has only one entry for 'WCD9335_IRQ_SLIMBUS'.
So 'devm_request...irq()' + explicit 'free_irq()' would lead to a double
free.
Remove the unneeded 'free_irq()' from the remove function.
Fixes: 20aedafdf4 ("ASoC: wcd9335: add support to wcd9335 codec")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Message-Id: <0614d63bc00edd7e81dd367504128f3d84f72efa.1629091028.git.christophe.jaillet@wanadoo.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f15a2a09c ]
If an error occurs after a successful 'clk_prepare_enable()' call, it must
be undone by a corresponding 'clk_disable_unprepare()' call.
This call is already present in the remove function.
Add this call in the error handling path and reorder the code so that the
'clk_prepare_enable()' call happens later in the function.
The goal is to have as much managed resources functions as possible
before the 'clk_prepare_enable()' call in order to keep the error handling
path simple.
While at it, remove the now unneeded 'clk' variable.
Fixes: c87dca0478 ("usb: bdc: Add clock enable for new chips with a separate BDC clock")
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/f8a4a6897deb0c8cb2e576580790303550f15fcd.1629314734.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4720f1bf4e ]
ehci_orion_drv_probe() did not account for possible errors of
clk_prepare_enable() that in particular could cause invocation of
clk_disable_unprepare() on clocks that were not prepared/enabled yet,
e.g. in remove or on handling errors of usb_add_hcd() in probe. Though,
there were several patches fixing different issues with clocks in this
driver, they did not solve this problem.
Add handling of errors of clk_prepare_enable() in ehci_orion_drv_probe()
to avoid calls of clk_disable_unprepare() without previous successful
invocation of clk_prepare_enable().
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 8c869edaee ("ARM: Orion: EHCI: Add support for enabling clocks")
Co-developed-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Link: https://lore.kernel.org/r/20210825170902.11234-1-novikov@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 661e8a88e8 ]
Iff platform_get_irq() returns 0 for the main IRQ, the driver's probe()
method will return 0 early (as if the method's call was successful).
Let's consider IRQ0 valid for simplicity -- devm_request_irq() can always
override that decision...
Fixes: 2bbd681ba2 ("i2c: xlp9xx: Driver for Netlogic XLP9XX/5XX I2C controller")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: George Cherian <george.cherian@marvell.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f980d055a0 ]
strlcpy() reads the entire source buffer first. This read may exceed the
destination size limit. This is both inefficient and can lead to linear
read overflows if a source string is not NUL-terminated.
Also, the strnlen() call does not avoid the read overflow in the strlcpy
function when a not NUL-terminated string is passed.
So, replace this block by a call to kstrndup() that avoids this type of
overflow and does the same.
Fixes: 066ce68994 ("cifs: rename cifs_strlcpy_to_host and make it use new functions")
Signed-off-by: Len Baker <len.baker@gmx.com>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7af7e497f ]
Fix a verifier bug found by smatch static checker in [0].
This problem has never been seen in prod to my best knowledge. Fixing it
still seems to be a good idea since it's hard to say for sure whether
it's possible or not to have a scenario where a combination of
convert_ctx_access() and a narrow load would lead to an out of bound
write.
When narrow load is handled, one or two new instructions are added to
insn_buf array, but before it was only checked that
cnt >= ARRAY_SIZE(insn_buf)
And it's safe to add a new instruction to insn_buf[cnt++] only once. The
second try will lead to out of bound write. And this is what can happen
if `shift` is set.
Fix it by making sure that if the BPF_RSH instruction has to be added in
addition to BPF_AND then there is enough space for two more instructions
in insn_buf.
The full report [0] is below:
kernel/bpf/verifier.c:12304 convert_ctx_accesses() warn: offset 'cnt' incremented past end of array
kernel/bpf/verifier.c:12311 convert_ctx_accesses() warn: offset 'cnt' incremented past end of array
kernel/bpf/verifier.c
12282
12283 insn->off = off & ~(size_default - 1);
12284 insn->code = BPF_LDX | BPF_MEM | size_code;
12285 }
12286
12287 target_size = 0;
12288 cnt = convert_ctx_access(type, insn, insn_buf, env->prog,
12289 &target_size);
12290 if (cnt == 0 || cnt >= ARRAY_SIZE(insn_buf) ||
^^^^^^^^^^^^^^^^^^^^^^^^^^^
Bounds check.
12291 (ctx_field_size && !target_size)) {
12292 verbose(env, "bpf verifier is misconfigured\n");
12293 return -EINVAL;
12294 }
12295
12296 if (is_narrower_load && size < target_size) {
12297 u8 shift = bpf_ctx_narrow_access_offset(
12298 off, size, size_default) * 8;
12299 if (ctx_field_size <= 4) {
12300 if (shift)
12301 insn_buf[cnt++] = BPF_ALU32_IMM(BPF_RSH,
^^^^^
increment beyond end of array
12302 insn->dst_reg,
12303 shift);
--> 12304 insn_buf[cnt++] = BPF_ALU32_IMM(BPF_AND, insn->dst_reg,
^^^^^
out of bounds write
12305 (1 << size * 8) - 1);
12306 } else {
12307 if (shift)
12308 insn_buf[cnt++] = BPF_ALU64_IMM(BPF_RSH,
12309 insn->dst_reg,
12310 shift);
12311 insn_buf[cnt++] = BPF_ALU64_IMM(BPF_AND, insn->dst_reg,
^^^^^^^^^^^^^^^
Same.
12312 (1ULL << size * 8) - 1);
12313 }
12314 }
12315
12316 new_prog = bpf_patch_insn_data(env, i + delta, insn_buf, cnt);
12317 if (!new_prog)
12318 return -ENOMEM;
12319
12320 delta += cnt - 1;
12321
12322 /* keep walking new program and skip insns we just inserted */
12323 env->prog = new_prog;
12324 insn = new_prog->insnsi + i + delta;
12325 }
12326
12327 return 0;
12328 }
[0] https://lore.kernel.org/bpf/20210817050843.GA21456@kili/
v1->v2:
- clarify that problem was only seen by static checker but not in prod;
Fixes: 46f53a65d2 ("bpf: Allow narrow loads with offset > 0")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210820163935.1902398-1-rdna@fb.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8b374b649 ]
Module configuration may differ between its instances depending on
resources required and input and output audio format. Available
parameters to select from are stored in module resource and interface
(format) lists. These come from topology, together with description of
each of pipe's modules.
Ignoring index value provided by topology and relying always on 0th
entry leads to unexpected module behavior due to under/overbudged
resources assigned or impropper format selection. Fix by taking entry at
index specified by topology.
Fixes: f6fa56e225 ("ASoC: Intel: Skylake: Parse and update module config structure")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Tested-by: Lukasz Majczak <lma@semihalf.com>
Link: https://lore.kernel.org/r/20210818075742.1515155-5-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a28dc123fa ]
Patch 96b1454f2e ("gfs2: move freeze glock outside the make_fs_rw and _ro
functions") changed the gfs2 mount sequence so that it holds the freeze
lock before calling gfs2_make_fs_rw. Before this patch, gfs2_make_fs_rw
called init_threads to initialize the quotad and logd threads. That is a
problem if the system needs to withdraw due to IO errors early in the
mount sequence, for example, while initializing the system statfs inode:
1. An IO error causes the statfs glock to not sync properly after
recovery, and leaves items on the ail list.
2. The leftover items on the ail list causes its do_xmote call to fail,
which makes it want to withdraw. But since the glock code cannot
withdraw (because the withdraw sequence uses glocks) it relies upon
the logd daemon to initiate the withdraw.
3. The withdraw can never be performed by the logd daemon because all
this takes place before the logd daemon is started.
This patch moves function init_threads from super.c to ops_fstype.c
and it changes gfs2_fill_super to start its threads before holding the
freeze lock, and if there's an error, stop its threads after releasing
it. This allows the logd to run unblocked by the freeze lock. Thus,
the logd daemon can perform its withdraw sequence properly.
Fixes: 96b1454f2e ("gfs2: move freeze glock outside the make_fs_rw and _ro functions")
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2478b9c1dc ]
Remove dev_err() messages after platform_get_irq*() failures.
drivers/i2c/busses/i2c-hix5hd2.c:417:2-9: line 417 is redundant
because platform_get_irq() already prints an error
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6840a5e37 ]
Iff platform_get_irq() returns 0, the driver's probe() method will return 0
early (as if the method's call was successful). Let's consider IRQ0 valid
for simplicity -- devm_request_irq() can always override that decision...
Fixes: e0d1ec9785 ("i2c-s3c2410: Change IRQ to be plain integer.")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a129950516 ]
When adding the code to handle platform_get_irq*() errors in the commit
489447380a ("handle errors returned by platform_get_irq*()"), the
actual error code was enforced to be -ENXIO in the driver for some
strange reason. This didn't matter much until the deferred probing was
introduced -- which requires an actual error code to be propagated
upstream from the failure site.
While fixing this, also stop overriding the errors from request_irq() to
-EIO (done since the pre-git era).
Fixes: 489447380a ("[PATCH] handle errors returned by platform_get_irq*()")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f41a4b2b5e ]
Syzbot hit "task hung" bug in hci_req_sync(). The problem was in
unreasonable huge inquiry timeout passed from userspace.
Fix it by adding sanity check for timeout value to hci_inquiry().
Since hci_inquiry() is the only user of hci_req_sync() with user
controlled timeout value, it makes sense to check timeout value in
hci_inquiry() and don't touch hci_req_sync().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-and-tested-by: syzbot+be2baed593ea56c6a84c@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1f278da6b ]
When scsi_dispatch_cmd was moved to scsi_lib.c and made static, some
compilers (i.e., at least gcc 8.4.0) decided to compile this
inline. This is a problem for lkdtm.ko, which inserted a kprobe
on this function for the SCSI_DISPATCH_CMD crashpoint.
Move this crashpoint one function up the call chain to
scsi_queue_rq. Though this is also a static function, it should never be
inlined because it is assigned as a structure entry. Therefore,
kprobe_register should always be able to find it.
Fixes: 82042a2cdb ("scsi: move scsi_dispatch_cmd to scsi_lib.c")
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kevin Mitchell <kevmitch@arista.com>
Link: https://lore.kernel.org/r/20210819022940.561875-2-kevmitch@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36ca7943ac ]
When the max pages (last_page in the swap header + 1) is smaller than
the total pages (inode size) of the swapfile, iomap_swapfile_activate
overwrites sis->max with total pages.
However, frontswap_map is a swap page state bitmap allocated using the
initial sis->max page count read from the swap header. If swapfile
activation increases sis->max, it's possible for the frontswap code to
walk off the end of the bitmap, thereby corrupting kernel memory.
[djwong: modify the description a bit; the original paragraph reads:
"However, frontswap_map is allocated using max pages. When test and clear
the sis offset, which is larger than max pages, of frontswap_map in
__frontswap_invalidate_page(), neighbors of frontswap_map may be
overwritten, i.e., slab is polluted."
Note also that this bug resulted in a behavioral change: activating a
swap file that was formatted and later extended results in all pages
being activated, not the number of pages recorded in the swap header.]
This fixes the issue by considering the limitation of max pages of swap
info in iomap_swapfile_add_extent().
To reproduce the case, compile kernel with slub RED ZONE, then run test:
$ sudo stress-ng -a 1 -x softlockup,resources -t 72h --metrics --times \
--verify -v -Y /root/tmpdir/stress-ng/stress-statistic-12.yaml \
--log-file /root/tmpdir/stress-ng/stress-logfile-12.txt \
--temp-path /root/tmpdir/stress-ng/
We'll get the error log as below:
[ 1151.015141] =============================================================================
[ 1151.016489] BUG kmalloc-16 (Not tainted): Right Redzone overwritten
[ 1151.017486] -----------------------------------------------------------------------------
[ 1151.017486]
[ 1151.018997] Disabling lock debugging due to kernel taint
[ 1151.019873] INFO: 0x0000000084e43932-0x0000000098d17cae @offset=7392. First byte 0x0 instead of 0xcc
[ 1151.021303] INFO: Allocated in __do_sys_swapon+0xcf6/0x1170 age=43417 cpu=9 pid=3816
[ 1151.022538] __slab_alloc+0xe/0x20
[ 1151.023069] __kmalloc_node+0xfd/0x4b0
[ 1151.023704] __do_sys_swapon+0xcf6/0x1170
[ 1151.024346] do_syscall_64+0x33/0x40
[ 1151.024925] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 1151.025749] INFO: Freed in put_cred_rcu+0xa1/0xc0 age=43424 cpu=3 pid=2041
[ 1151.026889] kfree+0x276/0x2b0
[ 1151.027405] put_cred_rcu+0xa1/0xc0
[ 1151.027949] rcu_do_batch+0x17d/0x410
[ 1151.028566] rcu_core+0x14e/0x2b0
[ 1151.029084] __do_softirq+0x101/0x29e
[ 1151.029645] asm_call_irq_on_stack+0x12/0x20
[ 1151.030381] do_softirq_own_stack+0x37/0x40
[ 1151.031037] do_softirq.part.15+0x2b/0x30
[ 1151.031710] __local_bh_enable_ip+0x4b/0x50
[ 1151.032412] copy_fpstate_to_sigframe+0x111/0x360
[ 1151.033197] __setup_rt_frame+0xce/0x480
[ 1151.033809] arch_do_signal+0x1a3/0x250
[ 1151.034463] exit_to_user_mode_prepare+0xcf/0x110
[ 1151.035242] syscall_exit_to_user_mode+0x27/0x190
[ 1151.035970] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 1151.036795] INFO: Slab 0x000000003b9de4dc objects=44 used=9 fp=0x00000000539e349e flags=0xfffffc0010201
[ 1151.038323] INFO: Object 0x000000004855ba01 @offset=7376 fp=0x0000000000000000
[ 1151.038323]
[ 1151.039683] Redzone 000000008d0afd3d: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc ................
[ 1151.041180] Object 000000004855ba01: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
[ 1151.042714] Redzone 0000000084e43932: 00 00 00 c0 cc cc cc cc ........
[ 1151.044120] Padding 000000000864c042: 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZZZZZZZZZ
[ 1151.045615] CPU: 5 PID: 3816 Comm: stress-ng Tainted: G B 5.10.50+ #7
[ 1151.046846] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
[ 1151.048633] Call Trace:
[ 1151.049072] dump_stack+0x57/0x6a
[ 1151.049585] check_bytes_and_report+0xed/0x110
[ 1151.050320] check_object+0x1eb/0x290
[ 1151.050924] ? __x64_sys_swapoff+0x39a/0x540
[ 1151.051646] free_debug_processing+0x151/0x350
[ 1151.052333] __slab_free+0x21a/0x3a0
[ 1151.052938] ? _cond_resched+0x2d/0x40
[ 1151.053529] ? __vunmap+0x1de/0x220
[ 1151.054139] ? __x64_sys_swapoff+0x39a/0x540
[ 1151.054796] ? kfree+0x276/0x2b0
[ 1151.055307] kfree+0x276/0x2b0
[ 1151.055832] __x64_sys_swapoff+0x39a/0x540
[ 1151.056466] do_syscall_64+0x33/0x40
[ 1151.057084] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 1151.057866] RIP: 0033:0x150340b0ffb7
[ 1151.058481] Code: Unable to access opcode bytes at RIP 0x150340b0ff8d.
[ 1151.059537] RSP: 002b:00007fff7f4ee238 EFLAGS: 00000246 ORIG_RAX: 00000000000000a8
[ 1151.060768] RAX: ffffffffffffffda RBX: 00007fff7f4ee66c RCX: 0000150340b0ffb7
[ 1151.061904] RDX: 000000000000000a RSI: 0000000000018094 RDI: 00007fff7f4ee860
[ 1151.063033] RBP: 00007fff7f4ef980 R08: 0000000000000000 R09: 0000150340a672bd
[ 1151.064135] R10: 00007fff7f4edca0 R11: 0000000000000246 R12: 0000000000018094
[ 1151.065253] R13: 0000000000000005 R14: 000000000160d930 R15: 00007fff7f4ee66c
[ 1151.066413] FIX kmalloc-16: Restoring 0x0000000084e43932-0x0000000098d17cae=0xcc
[ 1151.066413]
[ 1151.067890] FIX kmalloc-16: Object at 0x000000004855ba01 not freed
Fixes: 67482129cd ("iomap: add a swapfile activation function")
Fixes: a45c0eccc5 ("iomap: move the swapfile code into a separate file")
Signed-off-by: Gang Deng <gavin.dg@linux.alibaba.com>
Signed-off-by: Xu Yu <xuyu@linux.alibaba.com>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2af0c5ffad ]
If IRQ occurs between calling request_irq() and mv_u3d_eps_init(),
then null pointer dereference occurs since u3d->eps[] wasn't
initialized yet but used in mv_u3d_nuke().
The patch puts registration of the interrupt handler after
initializing of neccesery data.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 90fccb529d ("usb: gadget: Gadget directory cleanup - group UDC drivers")
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Link: https://lore.kernel.org/r/20210818141247.4794-1-lutovinova@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e7c57355a ]
When unbinding the firmware device we need to make sure it has no
consumers left. Otherwise we'd leave them with a firmware handle
pointing at freed memory.
Keep a reference count of all consumers and introduce rpi_firmware_put()
which will permit automatically decrease the reference count upon
unbinding consumer drivers.
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d744da241 ]
The driver overrides the error codes returned by platform_get_irq() to
-ENODEV, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the
error codes upstream.
Fixes: 0d676a6c43 ("i2c: add support for Socionext SynQuacer I2C controller")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbfa6f33e3 ]
Commit 0a0a66c984 ("clk: staging: Specify IOMEM dependency for Xilinx
Clocking Wizard driver") introduces a dependency on the non-existing config
IOMEM, which basically makes it impossible to include this driver into any
build. Fortunately, ./scripts/checkkconfigsymbols.py warns:
IOMEM
Referencing files: drivers/staging/clocking-wizard/Kconfig
The config for IOMEM support is called HAS_IOMEM. Correct this reference to
the intended config.
Fixes: 0a0a66c984 ("clk: staging: Specify IOMEM dependency for Xilinx Clocking Wizard driver")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20210817105404.13146-1-lukas.bulwahn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 514ef1e62d ]
Current PCIe MEM space of size 16 MB is not enough for some combination
of PCIe cards (e.g. NVMe disk together with ath11k wifi card). ARM Trusted
Firmware for Armada 3700 platform already assigns 128 MB for PCIe window,
so extend PCIe MEM space to the end of 128 MB PCIe window which allows to
allocate more PCIe BARs for more PCIe cards.
Without this change some combination of PCIe cards cannot be used and
kernel show error messages in dmesg during initialization:
pci 0000:00:00.0: BAR 8: no space for [mem size 0x01800000]
pci 0000:00:00.0: BAR 8: failed to assign [mem size 0x01800000]
pci 0000:00:00.0: BAR 6: assigned [mem 0xe8000000-0xe80007ff pref]
pci 0000:01:00.0: BAR 8: no space for [mem size 0x01800000]
pci 0000:01:00.0: BAR 8: failed to assign [mem size 0x01800000]
pci 0000:02:03.0: BAR 8: no space for [mem size 0x01000000]
pci 0000:02:03.0: BAR 8: failed to assign [mem size 0x01000000]
pci 0000:02:07.0: BAR 8: no space for [mem size 0x00100000]
pci 0000:02:07.0: BAR 8: failed to assign [mem size 0x00100000]
pci 0000:03:00.0: BAR 0: no space for [mem size 0x01000000 64bit]
pci 0000:03:00.0: BAR 0: failed to assign [mem size 0x01000000 64bit]
Due to bugs in U-Boot port for Turris Mox, the second range in Turris Mox
kernel DTS file for PCIe must start at 16 MB offset. Otherwise U-Boot
crashes during loading of kernel DTB file. This bug is present only in
U-Boot code for Turris Mox and therefore other Armada 3700 devices are not
affected by this bug. Bug is fixed in U-Boot version 2021.07.
To not break booting new kernels on existing versions of U-Boot on Turris
Mox, use first 16 MB range for IO and second range with rest of PCIe window
for MEM.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 76f6386b25 ("arm64: dts: marvell: Add Aardvark PCIe support for Armada 3700")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7104cc1a9 ]
This should use the network-namespace-wide client_lock, not the
per-client cl_lock.
You shouldn't see any bugs unless you're actually using the
forced-expiry interface introduced by 89c905becc.
Fixes: 89c905becc "nfsd: allow forced expiration of NFSv4 clients"
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd2d644ddb ]
After calling vfs_test_lock() the pointer to a conflicting lock can be
returned, and that lock is not guarunteed to be owned by nlm. In that
case, we cannot cast it to struct nlm_lockowner. Instead return the pid
of that conflicting lock.
Fixes: 646d73e91b ("lockd: Show pid of lockd for remote locks")
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8bbd97ad0 ]
If CONFIG_DEBUG_LOCK_ALLOC=y is enabled then local_lock_t has an 'owner'
member which is checked for consistency, but nothing initialized it to
zero explicitly.
The static initializer does so implicit, and the run time allocated per CPU
storage is usually zero initialized as well, but relying on that is not
really good practice.
Fixes: 91710728d1 ("locking: Introduce local_lock()")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20210815211301.969975279@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dfd5e3f5fe ]
The local_lock_t's are special, because they cannot form IRQ
inversions, make sure we can tell them apart from the rest of the
locks.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d45a1373e ]
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to request_threaded_irq() (which
takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding an
original error code. Stop calling request_threaded_irq() with the invalid
IRQ #s.
Fixes: 9ba96ae507 ("usb: omap1: Tahvo USB transceiver driver")
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/8280d6a4-8e9a-7cfe-1aa9-db586dc9afdf@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2f6662ac0 ]
Invoking atomic_notifier_chain_notify() requires acquiring a spinlock_t,
which can block under CONFIG_PREEMPT_RT. Notifications for members of the
cpu_pm notification chain will be issued by the idle task, which can never
block.
Making *all* atomic_notifiers use a raw_spinlock is too big of a hammer, as
only notifications issued by the idle task are problematic.
Special-case cpu_pm_notifier_chain by kludging a raw_notifier and
raw_spinlock_t together, matching the atomic_notifier behavior with a
raw_spinlock_t.
Fixes: 70d9329857 ("notifier: Fix broken error handling pattern")
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ea53674d0 ]
Commit 0ea9fd001a ("Bluetooth: Shutdown controller after workqueues
are flushed or cancelled") introduced a regression that makes mtkbtsdio
driver stops working:
[ 36.593956] Bluetooth: hci0: Firmware already downloaded
[ 46.814613] Bluetooth: hci0: Execution of wmt command timed out
[ 46.814619] Bluetooth: hci0: Failed to send wmt func ctrl (-110)
The shutdown callback depends on the result of hdev->rx_work, so we
should call it before flushing rx_work:
-> btmtksdio_shutdown()
-> mtk_hci_wmt_sync()
-> __hci_cmd_send()
-> wait for BTMTKSDIO_TX_WAIT_VND_EVT gets cleared
-> btmtksdio_recv_event()
-> hci_recv_frame()
-> queue_work(hdev->workqueue, &hdev->rx_work)
-> clears BTMTKSDIO_TX_WAIT_VND_EVT
So move the shutdown callback before flushing TX/RX queue to resolve the
issue.
Reported-and-tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Fixes: 0ea9fd001a ("Bluetooth: Shutdown controller after workqueues are flushed or cancelled")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f0c4f1b72 ]
Currently, "sample04" and "sample05" are not working properly when
running with an IPv6 option("-6"). The commit 0f06a6787e ("samples:
Add an IPv6 "-6" option to the pktgen scripts") has omitted the addition
of this option at "sample04" and "sample05".
In order to support IPv6 option, this commit adds logic related to IPv6
option.
Fixes: 0f06a6787e ("samples: Add an IPv6 "-6" option to the pktgen scripts")
Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed43fbac71 ]
The { 0 } doesn't clear all fields in the struct, but tells to the
compiler to set all fields to zero and doesn't touch any sub-fields
if they exists.
The {} is an empty initialiser that instructs to fully initialize whole
struct including sub-fields, which is error-prone for future
devlink_flash_notify extensions.
Fixes: 6700acc5f1 ("devlink: collect flash notify params into a struct")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d164dd9a5c ]
The "probed" part of test_core_autosize copies an integer using
bpf_core_read() into an integer of a potentially different size.
On big-endian machines a destination offset is required for this to
produce a sensible result.
Fixes: 888d83b961 ("selftests/bpf: Validate libbpf's auto-sizing of LD/ST/STX instructions")
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210812224814.187460-1-iii@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cea45a3bd2 ]
soc_device_match() is intended as a last resort, to handle e.g. quirks
that cannot be handled by matching based on a compatible value.
As the device nodes for the Renesas USB 3.0 Peripheral Controller on
R-Car E3 and RZ/G2E do have SoC-specific compatible values, the latter
can and should be used to match against these devices.
This also fixes support for the USB 3.0 Peripheral Controller on the
R-Car E3e (R8A779M6) SoC, which is a different grading of the R-Car E3
(R8A77990) SoC, using the same SoC-specific compatible value.
Fixes: 30025efa8b ("usb: gadget: udc: renesas_usb3: add support for r8a77990")
Fixes: 546970fdab ("usb: gadget: udc: renesas_usb3: add support for r8a774c0")
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/760981fb4cd110d7cbfc9dcffa365e7c8b25c6e5.1628696960.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0881e22c06 ]
The driver neglects to check the result of platform_get_irq()'s calls and
blithely passes the negative error codes to request_threaded_irq() (which
takes *unsigned* IRQ #), causing them both to fail with -EINVAL, overriding
an original error code. Stop calling request_threaded_irq() with the
invalid IRQ #s.
Fixes: c33fad0c37 ("usb: otg: Adding twl6030-usb transceiver driver for OMAP4430")
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/9507f50b-50f1-6dc4-f57c-3ed4e53a1c25@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ecc2f30dbb ]
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to request_irq() (which takes
*unsigned* IRQ #), causing it to fail with -EINVAL, overriding an original
error code. Stop calling request_irq() with the invalid IRQ #s.
Fixes: 0807c500a1 ("USB: add Freescale USB OTG Transceiver driver")
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/b0a86089-8b8b-122e-fd6d-73e8c2304964@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50855c3157 ]
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_irq() (which takes
*unsigned* IRQ #), causing it to fail with -EINVAL, overriding an original
error code. Stop calling devm_request_irq() with the invalid IRQ #s.
Fixes: 8b2e76687b ("USB: AT91 UDC updates, mostly power management")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Acked-by: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/6654a224-739a-1a80-12f0-76d920f87b6c@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1750069567 ]
In dwc3_qcom_acpi_register_core(), the driver neglects to check the result
of platform_get_irq()'s call and blithely assigns the negative error codes
to the allocated child device's IRQ resource and then passing this resource
to platform_device_add_resources() and later causing dwc3_otg_get_irq() to
fail anyway. Stop calling platform_device_add_resources() with the invalid
IRQ #s, so that there's less complexity in the IRQ error checking.
Fixes: 2bc02355f8 ("usb: dwc3: qcom: Add support for booting with ACPI")
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/45fec3da-1679-5bfe-5d74-219ca3fb28e7@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 772d44526e ]
When I booted up on a board that had a slightly different codec
stuffed on it, I got this message at bootup:
rt5682 9-001a: Device with ID register 6749 is not rt5682
That's normal/expected, but what wasn't normal was the splat that I
got after:
WARNING: CPU: 7 PID: 176 at drivers/regulator/core.c:2151 _regulator_put+0x150/0x158
pc : _regulator_put+0x150/0x158
...
Call trace:
_regulator_put+0x150/0x158
regulator_bulk_free+0x48/0x70
devm_regulator_bulk_release+0x20/0x2c
release_nodes+0x1cc/0x244
devres_release_all+0x44/0x60
really_probe+0x17c/0x378
...
This is because the error paths don't turn off the regulator. Let's
fix that.
Fixes: 0ddce71c21 ("ASoC: rt5682: add rt5682 codec driver")
Fixes: 87b42abae9 ("ASoC: rt5682: Implement remove callback")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210811081751.v2.1.I4a1d9aa5d99e05aeee15c2768db600158d76cab8@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6977cc89c8 ]
'of_find_device_by_node()' takes a reference that must be released when
not needed anymore.
This is expected to be done in 'dsi_destroy()'.
However, there are 2 issues in 'dsi_get_phy()'.
First, if 'of_find_device_by_node()' succeeds but 'platform_get_drvdata()'
returns NULL, 'msm_dsi->phy_dev' will still be NULL, and the reference
won't be released in 'dsi_destroy()'.
Secondly, as 'of_find_device_by_node()' already takes a reference, there is
no need for an additional 'get_device()'.
Move the assignment to 'msm_dsi->phy_dev' a few lines above and remove the
unneeded 'get_device()' to solve both issues.
Fixes: ec31abf668 ("drm/msm/dsi: Separate PHY to another platform device")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/f15bc57648a00e7c99f943903468a04639d50596.1628241097.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1dee2c1de ]
In commit 4e1a720d03 ("Bluetooth: avoid killing an already killed
socket"), a check was added to sco_sock_kill to skip killing a socket
if the SOCK_DEAD flag was set.
This was done after a trace for a use-after-free bug showed that the
same sock pointer was being killed twice.
Unfortunately, this check prevents sco_sock_kill from running on any
socket. sco_sock_kill kills a socket only if it's zapped and orphaned,
however sock_orphan announces that the socket is dead before detaching
it. i.e., orphaned sockets have the SOCK_DEAD flag set.
To fix this, we remove the check for SOCK_DEAD, and avoid repeated
calls to sco_sock_kill by removing incorrect calls in:
1. sco_sock_timeout. The socket should not be killed on timeout as
further processing is expected to be done. For example,
sco_sock_connect sets the timer then waits for the socket to be
connected or for an error to be returned.
2. sco_conn_del. This function should clean up resources for the
connection, but the socket itself should be cleaned up in
sco_sock_release.
3. sco_sock_close. Calls to sco_sock_close in sco_sock_cleanup_listen
and sco_sock_release are followed by sco_sock_kill. Hence the
duplicated call should be removed.
Fixes: 4e1a720d03 ("Bluetooth: avoid killing an already killed socket")
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4eeaed04e ]
Sparse warnings triggered truncating the IDs of some platform device
tables. Unfortunately some of the IDs in the match tables were missed
which breaks audio. The KBL change has been verified to fix audio, the
CML change was not tested as it was found through grepping the broken
changes and found to match the same situation in anticipation that it
should also be fixed.
Fixes: 94efd726b9 ("ASoC: Intel: kbl_da7219_max98357a: shrink platform_id below 20 characters")
Fixes: 24e46fb811 ("ASoC: Intel: bxt_da7219_max98357a: shrink platform_id below 20 characters")
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Tested-by: Matt Davis <mattedavis@google.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210809213544.1682444-1-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ba34d3c73 ]
The cpuset fields that manage partition root state do not strictly
follow the cpuset locking rule that update to cpuset has to be done
with both the callback_lock and cpuset_mutex held. This is now fixed
by making sure that the locking rule is upheld.
Fixes: 3881b86128 ("cpuset: Add an error state to cpuset.sched.partition")
Fixes: 4b842da276 ("cpuset: Make CPU hotplug work with partition")
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f3adb8a1e ]
Use more descriptive variable names for update_prstate(), remove
unnecessary code and fix some typos. There is no functional change.
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7fcc17d0cb ]
The Energy Model (EM) provides useful information about device power in
each performance state to other subsystems like: Energy Aware Scheduler
(EAS). The energy calculation in EAS does arithmetic operation based on
the EM em_cpu_energy(). Current implementation of that function uses
em_perf_state::cost as a pre-computed cost coefficient equal to:
cost = power * max_frequency / frequency.
The 'power' is expressed in milli-Watts (or in abstract scale).
There are corner cases when the EAS energy calculation for two Performance
Domains (PDs) return the same value. The EAS compares these values to
choose smaller one. It might happen that this values are equal due to
rounding error. In such scenario, we need better resolution, e.g. 1000
times better. To provide this possibility increase the resolution in the
em_perf_state::cost for 64-bit architectures. The cost of increasing
resolution on 32-bit is pretty high (64-bit division) and is not justified
since there are no new 32bit big.LITTLE EAS systems expected which would
benefit from this higher resolution.
This patch allows to avoid the rounding to milli-Watt errors, which might
occur in EAS energy estimation for each PD. The rounding error is common
for small tasks which have small utilization value.
There are two places in the code where it makes a difference:
1. In the find_energy_efficient_cpu() where we are searching for
best_delta. We might suffer there when two PDs return the same result,
like in the example below.
Scenario:
Low utilized system e.g. ~200 sum_util for PD0 and ~220 for PD1. There
are quite a few small tasks ~10-15 util. These tasks would suffer for
the rounding error. These utilization values are typical when running games
on Android. One of our partners has reported 5..10mA less battery drain
when running with increased resolution.
Some details:
We have two PDs: PD0 (big) and PD1 (little)
Let's compare w/o patch set ('old') and w/ patch set ('new')
We are comparing energy w/ task and w/o task placed in the PDs
a) 'old' w/o patch set, PD0
task_util = 13
cost = 480
sum_util_w/o_task = 215
sum_util_w_task = 228
scale_cpu = 1024
energy_w/o_task = 480 * 215 / 1024 = 100.78 => 100
energy_w_task = 480 * 228 / 1024 = 106.87 => 106
energy_diff = 106 - 100 = 6
(this is equal to 'old' PD1's energy_diff in 'c)')
b) 'new' w/ patch set, PD0
task_util = 13
cost = 480 * 1000 = 480000
sum_util_w/o_task = 215
sum_util_w_task = 228
energy_w/o_task = 480000 * 215 / 1024 = 100781
energy_w_task = 480000 * 228 / 1024 = 106875
energy_diff = 106875 - 100781 = 6094
(this is not equal to 'new' PD1's energy_diff in 'd)')
c) 'old' w/o patch set, PD1
task_util = 13
cost = 160
sum_util_w/o_task = 283
sum_util_w_task = 293
scale_cpu = 355
energy_w/o_task = 160 * 283 / 355 = 127.55 => 127
energy_w_task = 160 * 296 / 355 = 133.41 => 133
energy_diff = 133 - 127 = 6
(this is equal to 'old' PD0's energy_diff in 'a)')
d) 'new' w/ patch set, PD1
task_util = 13
cost = 160 * 1000 = 160000
sum_util_w/o_task = 283
sum_util_w_task = 293
scale_cpu = 355
energy_w/o_task = 160000 * 283 / 355 = 127549
energy_w_task = 160000 * 296 / 355 = 133408
energy_diff = 133408 - 127549 = 5859
(this is not equal to 'new' PD0's energy_diff in 'b)')
2. Difference in the 6% energy margin filter at the end of
find_energy_efficient_cpu(). With this patch the margin comparison also
has better resolution, so it's possible to have better task placement
thanks to that.
Fixes: 27871f7a8a ("PM: Introduce an Energy Model management framework")
Reported-by: CCJ Yeh <CCj.Yeh@mediatek.com>
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 713baf3dae ]
An earlier commit replaced using batostr to using %pMR sprintf for the
construction of session->name. Static analysis detected that this new
method can use a total of 21 characters (including the trailing '\0')
so we need to increase the BTNAMSIZ from 18 to 21 to fix potential
buffer overflows.
Addresses-Coverity: ("Out-of-bounds write")
Fixes: fcb73338ed ("Bluetooth: Use %pMR in sprintf/seq_printf instead of batostr")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 112cedc8e6 ]
If a kernel module gets unloaded then it printed report about a leak before
commit 275678e7a9 ("debugfs: Check module state before warning in
{full/open}_proxy_open()"). An additional check was added in this commit to
avoid this printing. But it was forgotten that the function must return an
error in this case because it was not actually opened.
As result, the systems started to crash or to hang when a module was
unloaded while something was trying to open a file.
Fixes: 275678e7a9 ("debugfs: Check module state before warning in {full/open}_proxy_open()")
Cc: Taehee Yoo <ap420073@gmail.com>
Reported-by: Mário Lopes <ml@simonwunderlich.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Link: https://lore.kernel.org/r/20210802162444.7848-1-sven@narfation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3d4571955 ]
The SMSM driver detects interrupt edges by tracking the last state
it has seen (and has triggered the interrupt handler for). This works
fine, but only if the interrupt does not change state while masked.
For example, if an interrupt is unmasked while the state is HIGH,
the stored last_value for that interrupt might still be LOW. Then,
when the remote processor triggers smsm_intr() we assume that nothing
has changed, even though the state might have changed from HIGH to LOW.
Attempt to fix this by checking the current remote state before
unmasking an IRQ. Use atomic operations to avoid the interrupt handler
from interfering with the unmask function.
This fixes modem crashes in some edge cases with the BAM-DMUX driver.
Specifically, the BAM-DMUX interrupt handler is not called for the
HIGH -> LOW smsm state transition if the BAM-DMUX driver is loaded
(and therefore unmasks the interrupt) after the modem was already started:
qcom-q6v5-mss 4080000.remoteproc: fatal error received: a2_task.c:3188:
Assert FALSE failed: A2 DL PER deadlock timer expired waiting for Apps ACK
Fixes: c97c4090ff ("soc: qcom: smsm: Add driver for Qualcomm SMSM")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210712135703.324748-2-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e00392a89 ]
PME signaling is only enabled by __pci_enable_wake() if the target
device can signal PME from the given target power state (to avoid
pointless reconfiguration of the device), but if the hierarchy above
the device goes into D3cold, the device itself will end up in D3cold
too, so if it can signal PME from D3cold, it should be enabled to
do so in __pci_enable_wake().
[Note that if the device does not end up in D3cold and it cannot
signal PME from the original target power state, it will not signal
PME, so in that case the behavior does not change.]
Link: https://lore.kernel.org/linux-pm/3149540.aeNJFYEL58@kreacher/
Fixes: 5bcc2fb4e8 ("PCI PM: Simplify PCI wake-up code")
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reported-by: Utkarsh H Patel <utkarsh.h.patel@intel.com>
Reported-by: Koba Ko <koba.ko@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da9f215068 ]
It is inconsistent to return PCI_D0 from pci_target_state() instead
of the original target state if 'wakeup' is true and the device
cannot signal PME from D0.
This only happens when the device cannot signal PME from the original
target state and any shallower power states (including D0) and that
case is effectively equivalent to the one in which PME singaling is
not supported at all. Since the original target state is returned in
the latter case, make the function do that in the former one too.
Link: https://lore.kernel.org/linux-pm/3149540.aeNJFYEL58@kreacher/
Fixes: 666ff6f83e ("PCI/PM: Avoid using device_may_wakeup() for runtime PM")
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reported-by: Utkarsh H Patel <utkarsh.h.patel@intel.com>
Reported-by: Koba Ko <koba.ko@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09ea9719a4 ]
Currently the call to find_format can potentially return a NULL to
fmt and the nullpointer is later dereferenced on the assignment of
pixmp->num_planes = fmt->num_planes. Fix this by adding a NULL pointer
check and returning NULL for the failure case.
Addresses-Coverity: ("Dereference null return")
Fixes: aaaa93eda6 ("[media] media: venus: venc: add video encoder files")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6fa54bc713 ]
If em28xx_ir_init fails, it would decrease the refcount of dev. However,
in the em28xx_ir_fini, when ir is NULL, it goes to ref_put and decrease
the refcount of dev. This will lead to a refcount bug.
Fix this bug by removing the kref_put in the error handling code
of em28xx_ir_init.
refcount_t: underflow; use-after-free.
WARNING: CPU: 0 PID: 7 at lib/refcount.c:28 refcount_warn_saturate+0x18e/0x1a0 lib/refcount.c:28
Modules linked in:
CPU: 0 PID: 7 Comm: kworker/0:1 Not tainted 5.13.0 #3
Workqueue: usb_hub_wq hub_event
RIP: 0010:refcount_warn_saturate+0x18e/0x1a0 lib/refcount.c:28
Call Trace:
kref_put.constprop.0+0x60/0x85 include/linux/kref.h:69
em28xx_usb_disconnect.cold+0xd7/0xdc drivers/media/usb/em28xx/em28xx-cards.c:4150
usb_unbind_interface+0xbf/0x3a0 drivers/usb/core/driver.c:458
__device_release_driver drivers/base/dd.c:1201 [inline]
device_release_driver_internal+0x22a/0x230 drivers/base/dd.c:1232
bus_remove_device+0x108/0x160 drivers/base/bus.c:529
device_del+0x1fe/0x510 drivers/base/core.c:3540
usb_disable_device+0xd1/0x1d0 drivers/usb/core/message.c:1419
usb_disconnect+0x109/0x330 drivers/usb/core/hub.c:2221
hub_port_connect drivers/usb/core/hub.c:5151 [inline]
hub_port_connect_change drivers/usb/core/hub.c:5440 [inline]
port_event drivers/usb/core/hub.c:5586 [inline]
hub_event+0xf81/0x1d40 drivers/usb/core/hub.c:5668
process_one_work+0x2c9/0x610 kernel/workqueue.c:2276
process_scheduled_works kernel/workqueue.c:2338 [inline]
worker_thread+0x333/0x5b0 kernel/workqueue.c:2424
kthread+0x188/0x1d0 kernel/kthread.c:319
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:295
Reported-by: Dongliang Mu <mudongliangabcd@gmail.com>
Fixes: ac56886371 ("media: em28xx: Fix possible memory leak of em28xx struct")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64f67b5240 ]
Some 2-in-1s with a detachable (USB) keyboard(dock) have mute-LEDs in
the speaker- and/or mic-mute keys on the keyboard.
Examples of this are the Lenovo Thinkpad10 tablet (with its USB kbd-dock)
and the HP x2 10 series.
The detachable nature of these keyboards means that the keyboard and
thus the mute LEDs may show up after the user (or userspace restoring
old mixer settings) has muted the speaker and/or mic.
Current LED-class devices with a default_trigger of "audio-mute" or
"audio-micmute" initialize the brightness member of led_classdev with
ledtrig_audio_get() before registering the LED.
This makes the software state after attaching the keyboard match the
actual audio mute state, e.g. cat /sys/class/leds/foo/brightness will
show the right value.
But before this commit nothing was actually calling the led_classdev's
brightness_set[_blocking] callback so the value returned by
ledtrig_audio_get() was never actually being sent to the hw, leading
to the mute LEDs staying in their default power-on state, after
attaching the keyboard, even if ledtrig_audio_get() returned a different
state.
This could be fixed by having the individual LED drivers call
brightness_set[_blocking] themselves after registering the LED,
but this really is something which should be done by a led-trigger
activate callback.
Add an activate callback for this, fixing the issue of the
mute LEDs being out of sync after (re)attaching the keyboard.
Cc: Takashi Iwai <tiwai@suse.de>
Fixes: faa2541f5b ("leds: trigger: Introduce audio mute LED trigger")
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e1baaaa24 ]
device_get_next_child_node() bumps a reference counting of a returned variable.
We have to balance it whenever we return to the caller.
Fixes: 8cd7d6daba ("leds: lt3593: Add device tree probing glue")
Cc: Daniel Mack <daniel@zonque.org>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f16a3bb69a ]
The driver is written as if platform_get_irq() returns 0 on errors (while
actually it returns a negative error code), blithely passing these error
codes to request_irq() (which takes *unsigned* IRQ #) -- which fails with
-EINVAL. Add the necessary error check to the pre-existing *if* statement
forcing the driver into the polling mode...
Fixes: 4ad48e6ab1 ("i2c: Renesas Highlander FPGA SMBus support")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c96ca5604a ]
Hihope boards use Realtek PHY. From the very beginning it use only
tx delays. However the phy driver commit bbc4d71d63
("net: phy: realtek: fix rtl8211e rx/tx delay config") introduced
NFS mount failure. Now it needs rx delay inaddition to tx delay
for NFS mount to work. This patch fixes NFS mount failure issue
by adding MAC internal rx delay.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Fixes: bbc4d71d63 ("net: phy: realtek: fix rtl8211e rx/tx delay config")
Link: https://lore.kernel.org/r/20210721180632.15080-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5200e63af ]
Some EtherAVB variants support internal clock delay configuration, which
can add larger delays than the delays that are typically supported by
the PHY (using an "rgmii-*id" PHY mode, and/or "[rt]xc-skew-ps"
properties).
Historically, the EtherAVB driver configured these delays based on the
"rgmii-*id" PHY mode. This was wrong, as these are meant solely for the
PHY, not for the MAC. Hence properties were introduced for explicit
configuration of these delays.
Convert the RZ/G2 DTS files from the old to the new scheme:
- Add default "rx-internal-delay-ps" and "tx-internal-delay-ps"
properties to the SoC .dtsi files, to be overridden by board files
where needed,
- Convert board files from "rgmii-*id" PHY modes to "rgmii", adding
the appropriate "rx-internal-delay-ps" and/or "tx-internal-delay-ps"
overrides.
Notes:
- RZ/G2E does not support TX internal delay handling.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200819134344.27813-8-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a25fca4d3c ]
This patch fixes the MGMT add_advertising command repsones with the
wrong opcode when it is trying to return the not supported error.
Fixes: cbbdfa6f33 ("Bluetooth: Enable controller RPA resolution using Experimental feature")
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ca34a13f7 ]
Syzbot reported warning in netlbl_cipsov4_add(). The
problem was in too big doi_def->map.std->lvl.local_size
passed to kcalloc(). Since this value comes from userpace there is
no need to warn if value is not correct.
The same problem may occur with other kcalloc() calls in
this function, so, I've added __GFP_NOWARN flag to all
kcalloc() calls there.
Reported-and-tested-by: syzbot+cdd51ee2e6b0b2e18c0d@syzkaller.appspotmail.com
Fixes: 96cb8e3313 ("[NetLabel]: CIPSOv4 and Unlabeled packet integration")
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c9856e4ed ]
There is some sort of corner case behavior of the controller,
which could rarely be triggered at least on i.MX6SX connected
to 800x480 DPI panel and i.MX8MM connected to DPI->DSI->LVDS
bridged 1920x1080 panel (and likely on other setups too), where
the image on the panel shifts to the right and wraps around.
This happens either when the controller is enabled on boot or
even later during run time. The condition does not correct
itself automatically, i.e. the display image remains shifted.
It seems this problem is known and is due to sporadic underflows
of the LCDIF FIFO. While the LCDIF IP does have underflow/overflow
IRQs, neither of the IRQs trigger and neither IRQ status bit is
asserted when this condition occurs.
All known revisions of the LCDIF IP have CTRL1 RECOVER_ON_UNDERFLOW
bit, which is described in the reference manual since i.MX23 as
"
Set this bit to enable the LCDIF block to recover in the next
field/frame if there was an underflow in the current field/frame.
"
Enable this bit to mitigate the sporadic underflows.
Fixes: 45d59d7040 ("drm: Add new driver for MXSFB controller")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Abrecht <public@danielabrecht.ch>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Stefan Agner <stefan@agner.ch>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210620224701.189289-1-marex@denx.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15d428e6fe ]
In cpuset_hotplug_workfn(), the detection of whether the cpu list
has been changed is done by comparing the effective cpus of the top
cpuset with the cpu_active_mask. However, in the rare case that just
all the CPUs in the subparts_cpus are offlined, the detection fails
and the partition states are not updated correctly. Fix it by forcing
the cpus_updated flag to true in this particular case.
Fixes: 4b842da276 ("cpuset: Make CPU hotplug work with partition")
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26ab7b3845 ]
This commit does a cleanup in LRO configuration.
LRO is a parameter of an RQ, but its state is changed by modifying a TIR
related to the RQ.
The current status: LRO for tunneled packets is not supported in the
driver, inner TIRs may enable LRO on creation, but LRO status of inner
TIRs isn't changed in mlx5e_modify_tirs_lro(). This is inconsistent, but
as long as the firmware doesn't declare support for tunneled LRO, it
works, because the same RQs are shared between the inner and outer TIRs.
This commit does two fixes:
1. If the firmware has the tunneled LRO capability, LRO is blocked
altogether, because it's not possible to block it for inner TIRs only,
when the same RQs are shared between inner and outer TIRs, and the
driver won't be able to handle tunneled LRO traffic.
2. mlx5e_modify_tirs_lro() is patched to modify LRO state for all TIRs,
including inner ones, because all TIRs related to an RQ should agree on
their LRO state.
Fixes: 7b3722fa9e ("net/mlx5e: Support RSS for GRE tunneled packets")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c43f3865c ]
TIR's rx_hash_field_selector_inner can be enabled only when
tunneled_offload_en = 1. tunneled_offload_en is filled according to the
tunneled_offload_en field in struct mlx5e_params, which is false in the
IPoIB profile. On the other hand, the IPoIB profile passes inner_ttc =
true to mlx5e_create_indirect_tirs, which potentially allows the latter
function to attempt to create inner indirect TIRs without having
tunneled_offload_en set.
This commit prohibits this behavior by passing inner_ttc = false to
mlx5e_create_indirect_tirs. The latter function won't attempt to create
inner indirect TIRs.
As inner indirect TIRs are not created in the IPoIB profile (this commit
blocks it explicitly, and even before they would have failed to be
created), the call to mlx5e_create_inner_ttc_table in
mlx5i_create_flow_steering is a no-op and can be removed.
Fixes: 46dc933cee ("net/mlx5e: Provide explicit directive if to create inner indirect tirs")
Fixes: 458821c72b ("net/mlx5e: IPoIB, Add inner TTC table to IPoIB flow steering")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72ccc373b0 ]
After enabling CONFIG_REGULATOR_DEBUG=y we observer below debug logs.
Changes help link VCCK and VDDEE pwm regulator to 5V regulator supply
instead of dummy regulator.
[ 7.117140] pwm-regulator regulator-vcck: Looking up pwm-supply from device tree
[ 7.117153] pwm-regulator regulator-vcck: Looking up pwm-supply property in node /regulator-vcck failed
[ 7.117184] VCCK: supplied by regulator-dummy
[ 7.117194] regulator-dummy: could not add device link regulator.8: -ENOENT
[ 7.117266] VCCK: 860 <--> 1140 mV at 986 mV, enabled
[ 7.118498] VDDEE: will resolve supply early: pwm
[ 7.118515] pwm-regulator regulator-vddee: Looking up pwm-supply from device tree
[ 7.118526] pwm-regulator regulator-vddee: Looking up pwm-supply property in node /regulator-vddee failed
[ 7.118553] VDDEE: supplied by regulator-dummy
[ 7.118563] regulator-dummy: could not add device link regulator.9: -ENOENT
Fixes: 087a1d8b4e ("ARM: dts: meson8b: ec100: add the VDDEE regulator")
Fixes: 3e7db1c1b7 ("ARM: dts: meson8b: ec100: improve the description of the regulators")
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210705112358.3554-4-linux.amoon@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 876228e9f9 ]
After enabling CONFIG_REGULATOR_DEBUG=y we observe below debug logs.
Changes help link VCCK and VDDEE pwm regulator to 5V regulator supply
instead of dummy regulator.
[ 7.117140] pwm-regulator regulator-vcck: Looking up pwm-supply from device tree
[ 7.117153] pwm-regulator regulator-vcck: Looking up pwm-supply property in node /regulator-vcck failed
[ 7.117184] VCCK: supplied by regulator-dummy
[ 7.117194] regulator-dummy: could not add device link regulator.8: -ENOENT
[ 7.117266] VCCK: 860 <--> 1140 mV at 986 mV, enabled
[ 7.118498] VDDEE: will resolve supply early: pwm
[ 7.118515] pwm-regulator regulator-vddee: Looking up pwm-supply from device tree
[ 7.118526] pwm-regulator regulator-vddee: Looking up pwm-supply property in node /regulator-vddee failed
[ 7.118553] VDDEE: supplied by regulator-dummy
[ 7.118563] regulator-dummy: could not add device link regulator.9: -ENOENT
Fixes: 524d96083b ("ARM: dts: meson8b: odroidc1: add the CPU voltage regulator")
Fixes: 8bdf38be71 ("ARM: dts: meson8b: odroidc1: add the VDDEE regulator")
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[narmstrong: fixed typo in commit s/observer/observe/]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210705112358.3554-2-linux.amoon@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44cf630bcb ]
We are seeing "imprecise external abort (0x1406)" errors during boot
(which then cause the whole board to hang) on Meson8 (but not Meson8m2).
These are observed while trying to access the GPU's registers when the
MALI clock is running at it's default setting of 24MHz. The 3.10 vendor
kernel uses 318.75MHz as "default" GPU frequency. Using that makes the
"imprecise external aborts" go away.
Add the assigned-clocks and assigned-clock-rates properties to also bump
the MALI clock to 318.75MHz before accessing any of it's registers.
Fixes: 7d3f6b536e ("ARM: dts: meson8: add the Mali-450 MP6 GPU")
Reported-by: Demetris Ierokipides <ierokipides.dem@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210711214023.2163565-1-martin.blumenstingl@googlemail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 525e2f9fd0 ]
st->bucket stores the current bucket number.
st->offset stores the offset within this bucket that is the sk to be
seq_show(). Thus, st->offset only makes sense within the same
st->bucket.
These two variables are an optimization for the common no-lseek case.
When resuming the seq_file iteration (i.e. seq_start()),
tcp_seek_last_pos() tries to continue from the st->offset
at bucket st->bucket.
However, it is possible that the bucket pointed by st->bucket
has changed and st->offset may end up skipping the whole st->bucket
without finding a sk. In this case, tcp_seek_last_pos() currently
continues to satisfy the offset condition in the next (and incorrect)
bucket. Instead, regardless of the offset value, the first sk of the
next bucket should be returned. Thus, "bucket == st->bucket" check is
added to tcp_seek_last_pos().
The chance of hitting this is small and the issue is a decade old,
so targeting for the next tree.
Fixes: a8b690f98b ("tcp: Fix slowness in read /proc/net/tcp")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20210701200541.1033917-1-kafai@fb.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9af417610b ]
The bounds check of id is off-by-one and the comparison should
be >= rather >. Currently the WARN_ON_ONCE check does not stop
the out of range indexing of &ldev->ctx.table[id] so also add
a return path if the bounds are out of range.
Addresses-Coverity: ("Illegal address computation").
Fixes: 5609c185f2 ("6lowpan: iphc: add support for stateful compression")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59da0b38bc ]
Smatch complains that some of these struct members are not initialized
leading to a stack information disclosure:
net/bluetooth/sco.c:778 sco_conn_defer_accept() warn:
check that 'cp.retrans_effort' doesn't leak information
This seems like a valid warning. I've added a default case to fix
this issue.
Fixes: 2f69a82acf ("Bluetooth: Use voice setting in deferred SCO connection request")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c275e5d349 ]
Inside function mt9m114_detect(), variable "retvalue" could
be uninitialized if mt9m114_read_reg() returns error, however, it
is used in the later if statement, which is potentially unsafe.
The local variable "retvalue" is renamed to "model" to avoid
confusion.
Link: https://lore.kernel.org/linux-media/20210625053858.3862-1-yzhai003@ucr.edu
Fixes: ad85094 (media / atomisp: fix the uninitialized use of model ID)
Signed-off-by: Yizhuo <yzhai003@ucr.edu>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44693d74f5 ]
The frame memory control register value is currently determined
before userspace selects the final capture format and never corrected.
Update ctx->frame_mem_ctrl in __coda_start_decoding() to fix decoding
into YUV420 or YVU420 capture buffers.
Reported-by: Andrej Picej <andrej.picej@norik.com>
Fixes: 497e6b8559 ("media: coda: add sequence initialization work")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e58430e1d4 ]
There are a few bugs in this code. 1) No checks for whether
dma_alloc_attrs() or __get_free_pages() failed. 2) If
video_register_device() fails it doesn't clean up the dma attrs or the
free pages. 3) The video_device_release() function frees "vfd" which
leads to a use after free on the next line. The call to
video_unregister_device() is not required so I have just removed that.
Fixes: f7e7b48e6d ("[media] rockchip/rga: v4l2 m2m support")
Reported-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0314339a0a ]
Commit dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f5885a775 ]
In go7007_alloc() kzalloc() is used for struct go7007
allocation. It means that there is no need in zeroing
any members, because kzalloc will take care of it.
Removing these reduntant initialization steps increases
execution speed a lot:
Before:
+ 86.802 us | go7007_alloc();
After:
+ 29.595 us | go7007_alloc();
Fixes: 866b8695d6 ("Staging: add the go7007 video driver")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 131ae388b8 ]
In dvb_usb_i2c_init, if i2c_add_adapter fails, it only prints an error
message, and then continues to set DVB_USB_STATE_I2C. This affects the
logic of dvb_usb_i2c_exit, which leads to that, the deletion of i2c_adap
even if the i2c_add_adapter fails.
Fix this by returning at the failure of i2c_add_adapter and then move
dvb_usb_i2c_exit out of the error handling code of dvb_usb_i2c_init.
Fixes: 13a79f14ab ("media: dvb-usb: Fix memory leak at error in dvb_usb_device_init()")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 797c061ad7 ]
If vp702x_usb_in_op fails, the mac address is not initialized.
And vp702x_read_mac_addr does not handle this failure, which leads to
the uninit-value in dvb_usb_adapter_dvb_init.
Fix this by handling the failure of vp702x_usb_in_op.
Fixes: 786baecfe7 ("[media] dvb-usb: move it to drivers/media/usb/dvb-usb")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5453769f7 ]
If dibusb_read_eeprom_byte fails, the mac address is not initialized.
And nova_t_read_mac_address does not handle this failure, which leads to
the uninit-value in dvb_usb_adapter_dvb_init.
Fix this by handling the failure of dibusb_read_eeprom_byte.
Reported-by: syzbot+e27b4fd589762b0b9329@syzkaller.appspotmail.com
Fixes: 786baecfe7 ("[media] dvb-usb: move it to drivers/media/usb/dvb-usb")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2255ff477 ]
The failure to register devlink will leave the system with dangled
devlink resource, which is not cleaned if devlink_port_register() fails.
In order to remove access to ".registered" field of struct devlink_port,
require both devlink_register and devlink_port_register to success and
check it through device pointer.
Fixes: fbfb803153 ("ionic: Add hardware init and device commands")
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ecc8cb7c0 ]
This race was discovered when I carefully analyzed the code to locate
another firmware-related UAF issue. It can be triggered only when the
firmware load operation is executed during suspend. This possibility is
almost impossible because there are few firmware load and suspend actions
in the actual environment.
CPU0 CPU1
__device_uncache_fw_images(): assign_fw():
fw_cache_piggyback_on_request()
<----- P0
spin_lock(&fwc->name_lock);
...
list_del(&fce->list);
spin_unlock(&fwc->name_lock);
uncache_firmware(fce->name);
<----- P1
kref_get(&fw_priv->ref);
If CPU1 is interrupted at position P0, the new 'fce' has been added to the
list fwc->fw_names by the fw_cache_piggyback_on_request(). In this case,
CPU0 executes __device_uncache_fw_images() and will be able to see it when
it traverses list fwc->fw_names. Before CPU1 executes kref_get() at P1, if
CPU0 further executes uncache_firmware(), the count of fw_priv->ref may
decrease to 0, causing fw_priv to be released in advance.
Move kref_get() to the lock protection range of fwc->name_lock to fix it.
Fixes: ac39b3ea73 ("firmware loader: let caching firmware piggyback on loading firmware")
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20210719064531.3733-2-thunder.leizhen@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6579cbfd7 ]
In the case where IS_ERR(lsi->si_sc_inode) is true the error exit path
to free_local does not kfree the allocated object lsi leading to a memory
leak. Fix this by kfree'ing lst before taking the error exit path.
Addresses-Coverity: ("Resource leak")
Fixes: 97fd734ba1 ("gfs2: lookup local statfs inodes prior to journal recovery")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d43b3a989b ]
rpmhpd_aggregate_corner() takes a corner as parameter, but in
rpmhpd_power_off() the code requests the level of the first corner
instead.
In all (known) current cases the first corner has level 0, so this
change should be a nop, but in case that there's a power domain with a
non-zero lowest level this makes sure that rpmhpd_power_off() actually
requests the lowest level - which is the closest to "power off" we can
get.
While touching the code, also skip the unnecessary zero-initialization
of "ret".
Fixes: 279b7e8a62 ("soc: qcom: rpmhpd: Add RPMh power domain driver")
Reviewed-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20210703005416.2668319-2-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b4b06919f ]
i40e_config_vf_promiscuous_mode() calls
i40e_getnum_vf_vsi_vlan_filters() without acquiring the
mac_filter_hash_lock spinlock.
This is unsafe because mac_filter_hash may get altered in another thread
while i40e_getnum_vf_vsi_vlan_filters() traverses the hashes.
Simply adding the spinlock in i40e_getnum_vf_vsi_vlan_filters() is not
possible as it already gets called in i40e_get_vlan_list_sync() with the
spinlock held. Therefore adding a wrapper that acquires the spinlock and
call the correct function where appropriate.
Fixes: 37d318d780 ("i40e: Remove scheduling while atomic possibility")
Fix-suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63a9192b8f ]
The 'tail' pointer is also free-running count, so it needs to be masked
as 'adminq_prod_cnt' does, to become an index value of AdminQ buffer.
Fixes: 5cdad90de6 ("gve: Batch AQ commands for creating and destroying queues.")
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Reviewed-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75f0fc7b48 ]
In bpf_patch_insn_data(), we first use the bpf_patch_insn_single() to
insert new instructions, then use adjust_insn_aux_data() to adjust
insn_aux_data. If the old env->prog have no enough room for new inserted
instructions, we use bpf_prog_realloc to construct new_prog and free the
old env->prog.
There have two errors here. First, if adjust_insn_aux_data() return
ENOMEM, we should free the new_prog. Second, if adjust_insn_aux_data()
return ENOMEM, bpf_patch_insn_data() will return NULL, and env->prog has
been freed in bpf_prog_realloc, but we will use it in bpf_check().
So in this patch, we make the adjust_insn_aux_data() never fails. In
bpf_patch_insn_data(), we first pre-malloc memory for the new
insn_aux_data, then call bpf_patch_insn_single() to insert new
instructions, at last call adjust_insn_aux_data() to adjust
insn_aux_data.
Fixes: 8041902dae ("bpf: adjust insn_aux_data when patching insns")
Signed-off-by: He Fengqing <hefengqing@huawei.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20210714101815.164322-1-hefengqing@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dcb0145821 ]
If an error occurs after a successful 'regulator_enable()' call,
'regulator_disable()' must be called.
Fix the error handling path of the probe accordingly.
Fixes: cb496cd472 ("media: cxd2880-spi: Add optional vcc regulator")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e642197562 ]
The error code is missing in this code scenario, add the error code
'-EINVAL' to the return value 'ret'.
Eliminate the follow smatch warning:
drivers/leds/leds-is31fl32xx.c:388 is31fl32xx_parse_dt() warn: missing
error code 'ret'.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Fixes: 9d7cffaf99 ("leds: Add driver for the ISSI IS31FL32xx family of LED controllers")
Acked-by: David Rivshin <drivshin@allworx.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea3e1c36e3 ]
Without this patch, the TDA19971 chip's EDID is inactive.
EDID never worked with this driver, it was all tested with HDMI signal
sources which don't need EDID support.
Signed-off-by: Krzysztof Halasa <khalasa@piap.pl>
Fixes: 9ac0038db9 ("media: i2c: Add TDA1997x HDMI receiver driver")
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2294a7299f ]
MCDDRCFG is a per-channel register and uses bit{0,1} to indicate
the NVDIMM presence on DIMM slot{0,1}. Current i10nm_edac driver
wrongly uses MCDDRCFG as per-DIMM register and fails to detect
the NVDIMM.
Fix it by reading MCDDRCFG as per-channel register and using its
bit{0,1} to check whether the NVDIMM is populated on DIMM slot{0,1}.
Fixes: d4dc89d069 ("EDAC, i10nm: Add a driver for Intel 10nm server processors")
Reported-by: Fan Du <fan.du@intel.com>
Tested-by: Wen Jin <wen.jin@intel.com>
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/r/20210818175701.1611513-2-tony.luck@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26cfc0dbe4 ]
The function wait_for_completion_interruptible_timeout will return
-ERESTARTSYS immediately when receiving SIGKILL signal which is sent
by "jffs2_gcd_mtd" during umounting jffs2. This will break the SPI memory
operation because the data transmitting may begin before the command or
address transmitting completes. Use wait_for_completion_timeout to prevent
the process from being interruptible.
Fixes: 67dca5e580 ("spi: spi-mem: Add support for Zynq QSPI controller")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20210826005930.20572-1-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 98e47570ba ]
In commit e915331149 ("regulator: vctrl-regulator: Avoid deadlock getting
and setting the voltage"), all calls to get/set the voltage of the
control regulator were switched to unlocked versions to avoid deadlocks.
However, the call in the probe path is done without regulator locks
held. In this case the locked version should be used.
Switch back to the locked regulator_get_voltage() in the probe path to
avoid any mishaps.
Fixes: e915331149 ("regulator: vctrl-regulator: Avoid deadlock getting and setting the voltage")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20210825033704.3307263-2-wenst@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc40b72251 ]
dun_bytes needs to be less than or equal to the IV size of the
encryption mode, not just less than or equal to BLK_CRYPTO_MAX_IV_SIZE.
Currently this doesn't matter since blk_crypto_init_key() is never
actually passed invalid values, but we might as well fix this.
Fixes: a892c8d52c ("block: Inline encryption support for blk-mq")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20210825055918.51975-1-ebiggers@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3bff147b18 ]
When a fatal machine check results in a system reset, Linux does not
clear the error(s) from machine check bank(s) - hardware preserves the
machine check banks across a warm reset.
During initialization of the kernel after the reboot, Linux reads, logs,
and clears all machine check banks.
But there is a problem. In:
5de97c9f6d ("x86/mce: Factor out and deprecate the /dev/mcelog driver")
the call to mce_register_decode_chain() moved later in the boot
sequence. This means that /dev/mcelog doesn't see those early error
logs.
This was partially fixed by:
cd9c57cad3 ("x86/MCE: Dump MCE to dmesg if no consumers")
which made sure that the logs were not lost completely by printing
to the console. But parsing console logs is error prone. Users of
/dev/mcelog should expect to find any early errors logged to standard
places.
Add a new flag MCP_QUEUE_LOG to machine_check_poll() to be used in early
machine check initialization to indicate that any errors found should
just be queued to genpool. When mcheck_late_init() is called it will
call mce_schedule_work() to actually log and flush any errors queued in
the genpool.
[ Based on an original patch, commit message by and completely
productized by Tony Luck. ]
Fixes: 5de97c9f6d ("x86/mce: Factor out and deprecate the /dev/mcelog driver")
Reported-by: Sumanth Kamatala <skamatala@juniper.net>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20210824003129.GA1642753@agluck-desk2.amr.corp.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 047d4226b0 ]
When rngd is run as root then lots of these types of message will appear
in the kernel log if the TPM has been configured to provide random bytes:
[ 7406.275163] tpm tpm0: tpm_transmit: tpm_recv: error -4
The issue is caused by the following call that is interrupted while
waiting for the TPM's response.
sig = wait_event_interruptible(ibmvtpm->wq, !ibmvtpm->tpm_processing_cmd);
Rather than waiting for the response in the low level driver, have it use
the polling loop in tpm_try_transmit() that uses a command's duration to
poll until a result has been returned by the TPM, thus ending when the
timeout has occurred but not responding to signals and ctrl-c anymore. To
stay in this polling loop extend tpm_ibmvtpm_status() to return
'true' for as long as the vTPM is indicated as being busy in
tpm_processing_cmd. Since the loop requires the TPM's timeouts, get them
now using tpm_get_timeouts() after setting the TPM2 version flag on the
chip.
To recreat the resolved issue start rngd like this:
sudo rngd -r /dev/hwrng -t
sudo rngd -r /dev/tpm0 -t
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1981473
Fixes: 6674ff145e ("tpm_ibmvtpm: properly handle interrupted packet receptions")
Cc: Nayna Jain <nayna@linux.ibm.com>
Cc: George Wilson <gcwilson@linux.ibm.com>
Reported-by: Nageswara R Sastry <rnsastry@linux.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: Nageswara R Sastry <rnsastry@linux.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea35e0d5df ]
Address a kbuild issue where a developer created an ECDSA key for signing
kernel modules and then builds an older version of the kernel, when bi-
secting the kernel for example, that does not support ECDSA keys.
If openssl is installed, trigger the creation of an RSA module signing
key if it is not an RSA key.
Fixes: cfc411e7ff ("Move certificate handling to its own directory")
Cc: David Howells <dhowells@redhat.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 462354d986 ]
Replace vf_mask type with unsigned long to avoid a stack-out-of-bound.
This is to fix the following warning reported by KASAN the first time
adf_msix_isr_ae() gets called.
[ 692.091987] BUG: KASAN: stack-out-of-bounds in find_first_bit+0x28/0x50
[ 692.092017] Read of size 8 at addr ffff88afdf789e60 by task swapper/32/0
[ 692.092076] Call Trace:
[ 692.092089] <IRQ>
[ 692.092101] dump_stack+0x9c/0xcf
[ 692.092132] print_address_description.constprop.0+0x18/0x130
[ 692.092164] ? find_first_bit+0x28/0x50
[ 692.092185] kasan_report.cold+0x7f/0x111
[ 692.092213] ? static_obj+0x10/0x80
[ 692.092234] ? find_first_bit+0x28/0x50
[ 692.092262] find_first_bit+0x28/0x50
[ 692.092288] adf_msix_isr_ae+0x16e/0x230 [intel_qat]
Fixes: ed8ccaef52 ("crypto: qat - Add support for SRIOV")
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1a811633f ]
Syzbot hit WARNING in internal_create_group(). The problem was in
too big disk->first_minor.
disk->first_minor is initialized by value, which comes from userspace
and there wasn't any sanity checks about value correctness. It can cause
duplicate creation of sysfs files/links, because disk->first_minor will
be passed to MKDEV() which causes truncation to byte. Since maximum
minor value is 0xff, let's check if first_minor is correct minor number.
NOTE: the root case of the reported warning was in wrong error handling
in register_disk(), but we can avoid passing knowingly wrong values to
sysfs API, because sysfs error messages can confuse users. For example:
user passed 1048576 as index, but sysfs complains about duplicate
creation of /dev/block/43:0. It's not obvious how 1048576 becomes 0.
Log and reproducer for above example can be found on syzkaller bug
report page.
Link: https://syzkaller.appspot.com/bug?id=03c2ae9146416edf811958d5fd7acfab75b143d1
Fixes: b0d9111a2d ("nbd: use an idr to keep track of nbd devices")
Reported-by: syzbot+9937dc42271cd87d4b98@syzkaller.appspotmail.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be83c3b6e7 ]
If CMT instance has at least two channels, one channel will be used
as a clock source and another one used as a clock event device.
In that case, IRQ is not requested for clock source channel so
sh_cmt_clock_event_program_verify() might work incorrectly.
Besides, when a channel is only used for clock source, don't need to
re-set the next match_value since it should be maximum timeout as
it still is.
On the other hand, due to no IRQ, total_cycles is not counted up
when reaches compare match time (timer counter resets to zero),
so sh_cmt_clocksource_read() returns unexpected value.
Therefore, use 64-bit clocksoure's mask for 32-bit or 16-bit variants
will also lead to wrong delta calculation. Hence, this mask should
correspond to timer counter width, and above function just returns
the raw value of timer counter register.
Fixes: bfa76bb12f ("clocksource: sh_cmt: Request IRQ for clock event device only")
Fixes: 37e7742c55 ("clocksource/drivers/sh_cmt: Fix clocksource width for 32-bit machines")
Signed-off-by: Phong Hoang <phong.hoang.wz@renesas.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210422123443.73334-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6f756726e ]
We should set the additional space to 0 in mpi_resize().
So use kcalloc() instead of kmalloc_array().
In lib/mpi/ec.c:
/****************
* Resize the array of A to NLIMBS. the additional space is cleared
* (set to 0) [done by m_realloc()]
*/
int mpi_resize(MPI a, unsigned nlimbs)
Like the comment of kernel's mpi_resize() said, the additional space
need to be set to 0, but when a->d is not NULL, it does not set.
The kernel's mpi lib is from libgcrypt, the mpi resize in libgcrypt
is _gcry_mpi_resize() which set the additional space to 0.
This bug may cause mpi api which use mpi_resize() get wrong result
under the condition of using the additional space without initiation.
If this condition is not met, the bug would not be triggered.
Currently in kernel, rsa, sm2 and dh use mpi lib, and they works well,
so the bug is not triggered in these cases.
add_points_edwards() use the additional space directly, so it will
get a wrong result.
Fixes: cdec9cb516 ("crypto: GnuPG based MPI lib - source files (part 1)")
Signed-off-by: Hongbo Li <herberthbli@tencent.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 976c1de1de ]
Depending on the DMA driver being used, the struct dma_slave_config may
need to be initialized to zero for the unused data.
For example, we have three DMA drivers using src_port_window_size and
dst_port_window_size. If these are left uninitialized, it can cause DMA
failures.
For spi-pic32, this is probably not currently an issue but is still good to
fix though.
Fixes: 1bcb9f8ceb ("spi: spi-pic32: Add PIC32 SPI master driver")
Cc: Purna Chandra Mandal <purna.mandal@microchip.com>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210810081727.19491-2-tony@atomide.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 866663b7b5 ]
When merging one bio to request, if they are discard IO and the queue
supports multi-range discard, we need to return ELEVATOR_DISCARD_MERGE
because both block core and related drivers(nvme, virtio-blk) doesn't
handle mixed discard io merge(traditional IO merge together with
discard merge) well.
Fix the issue by returning ELEVATOR_DISCARD_MERGE in this situation,
so both blk-mq and drivers just need to handle multi-range discard.
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Fixes: 2705dfb209 ("block: fix discard request merge")
Link: https://lore.kernel.org/r/20210729034226.1591070-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2189e928b6 ]
When enabling CONFIG_RMW_INSNS in e.g. a Coldfire build:
{standard input}:3068: Error: invalid instruction for this architecture; needs 68020 or higher (68020 [68k, 68ec020], 68030 [68ec030], 68040 [68ec040], 68060 [68ec060]) -- statement `casl %d4,%d0,(%a6)' ignored
Fix this by (a) adding a new config symbol to track if support for any
CPU that lacks the CAS instruction is enabled, and (b) making
CONFIG_RMW_INSNS depend on the new symbol not being set.
Fixes: 0e152d8050 ("m68k: reorganize Kconfig options to improve mmu/non-mmu selections")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210725104413.318932-1-geert@linux-m68k.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc87740c8a ]
If rcu_print_task_stall() is invoked on an rcu_node structure that does
not contain any tasks blocking the current grace period, it takes an
early exit that fails to release that rcu_node structure's lock. This
results in a self-deadlock, which is detected by lockdep.
To reproduce this bug:
tools/testing/selftests/rcutorture/bin/kvm.sh --allcpus --duration 3 --trust-make --configs "TREE03" --kconfig "CONFIG_PROVE_LOCKING=y" --bootargs "rcutorture.stall_cpu=30 rcutorture.stall_cpu_block=1 rcutorture.fwd_progress=0 rcutorture.test_boost=0"
This will also result in other complaints, including RCU's scheduler
hook complaining about blocking rather than preemption and an rcutorture
writer stall.
Only a partial RCU CPU stall warning message will be printed because of
the self-deadlock.
This commit therefore releases the lock on the rcu_print_task_stall()
function's early exit path.
Fixes: c583bcb8f5 ("rcu: Don't invoke try_invoke_on_locked_down_task() with irqs disabled")
Tested-by: Qais Yousef <qais.yousef@arm.com>
Signed-off-by: Yanfei Xu <yanfei.xu@windriver.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a649d25dcc ]
This commit adds a number of lockdep_assert_irqs_disabled() calls
to rcu_sched_clock_irq() and a number of the functions that it calls.
The point of this is to help track down a situation where lockdep appears
to be insisting that interrupts are enabled within these functions, which
should only ever be invoked from the scheduling-clock interrupt handler.
Link: https://lore.kernel.org/lkml/20201111133813.GA81547@elver.google.com/
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6a901a44f ]
The for loop in rcu_print_task_stall() always omits ts[0], which points
to the first task blocking the stalled grace period. This in turn fails
to count this first task, which means that ndetected will be equal to
zero when all CPUs have passed through their quiescent states and only
one task is blocking the stalled grace period. This zero value for
ndetected will in turn result in an incorrect "All QSes seen" message:
rcu: INFO: rcu_preempt detected stalls on CPUs/tasks:
rcu: Tasks blocked on level-1 rcu_node (CPUs 12-23):
(detected by 15, t=6504 jiffies, g=164777, q=9011209)
rcu: All QSes seen, last rcu_preempt kthread activity 1 (4295252379-4295252378), jiffies_till_next_fqs=1, root ->qsmask 0x2
BUG: sleeping function called from invalid context at include/linux/uaccess.h:156
in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 70613, name: msgstress04
INFO: lockdep is turned off.
Preemption disabled at:
[<ffff8000104031a4>] create_object.isra.0+0x204/0x4b0
CPU: 15 PID: 70613 Comm: msgstress04 Kdump: loaded Not tainted
5.12.2-yoctodev-standard #1
Hardware name: Marvell OcteonTX CN96XX board (DT)
Call trace:
dump_backtrace+0x0/0x2cc
show_stack+0x24/0x30
dump_stack+0x110/0x188
___might_sleep+0x214/0x2d0
__might_sleep+0x7c/0xe0
This commit therefore fixes the loop to include ts[0].
Fixes: c583bcb8f5 ("rcu: Don't invoke try_invoke_on_locked_down_task() with irqs disabled")
Tested-by: Qais Yousef <qais.yousef@arm.com>
Signed-off-by: Yanfei Xu <yanfei.xu@windriver.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca4984a7dd ]
The UCLAMP_FLAG_IDLE flag is set on a runqueue when dequeueing the last
uclamp active task (that is, when buckets.tasks reaches 0 for all
buckets) to maintain the last uclamp.max and prevent blocked util from
suddenly becoming visible.
However, there is an asymmetry in how the flag is set and cleared which
can lead to having the flag set whilst there are active tasks on the rq.
Specifically, the flag is cleared in the uclamp_rq_inc() path, which is
called at enqueue time, but set in uclamp_rq_dec_id() which is called
both when dequeueing a task _and_ in the update_uclamp_active() path. As
a result, when both uclamp_rq_{dec,ind}_id() are called from
update_uclamp_active(), the flag ends up being set but not cleared,
hence leaving the runqueue in a broken state.
Fix this by clearing the flag in update_uclamp_active() as well.
Fixes: e496187da7 ("sched/uclamp: Enforce last task's UCLAMP_MAX")
Reported-by: Rick Yiu <rickyiu@google.com>
Signed-off-by: Quentin Perret <qperret@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Qais Yousef <qais.yousef@arm.com>
Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Link: https://lore.kernel.org/r/20210805102154.590709-2-qperret@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad1abe4769 ]
Deal with deferred probe using dev_err_probe so the error is handled
and avoid logging lots probe defer information like the following:
[ 9.125121] cw2015 4-0062: Failed to register power supply
[ 9.211131] cw2015 4-0062: Failed to register power supply
Fixes: b4c7715c10 ("power: supply: add CellWise cw2015 fuel gauge driver")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cabebb697c ]
If for any reason the interrupt enable for an ap queue fails the
state machine run for the queue returned wrong return codes to the
caller. So the caller assumed interrupt support for this queue in
enabled and thus did not re-establish the high resolution timer used
for polling. In the end this let to a hang for the user space process
waiting "forever" for the reply.
This patch reworks these return codes to return correct indications
for the caller to re-establish the timer when a queue runs without
interrupt support.
Please note that this is fixing a wrong behavior after a first
failure (enable interrupt support for the queue) failed. However,
looks like this occasionally happens on KVM systems.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9372a82892 ]
Currently allocation and registration of s390dbf debug areas are tied
together. As a result, a debug area cannot be unregistered and
re-registered while any process has an associated debugfs file open.
Fix this by splitting alloc/release from register/unregister.
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1204777867 ]
Any previously recorded s390dbf debug data is reset when a debug area
is resized using the 'pages' sysfs attribute. This can make
live-debugging unnecessarily complex.
Fix this by copying existing debug data to the newly allocated debug
area when resizing.
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7addcdd52 ]
Currently clp_set_pci_fn() always returns 0 as long as the CLP request
itself succeeds even if the operation itself returns a response code
other than CLP_RC_OK or CLP_RC_SETPCIFN_ALRDY. This is highly misleading
because calling code assumes that a zero rc means that the operation was
successful.
Fix this by returning the response code or cc on failure with the
exception of the special handling for CLP_RC_SETPCIFN_ALRDY. Also let's
not assume that the returned function handle for CLP_RC_SETPCIFN_ALRDY
is 0, we don't need it anyway.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f488f698f ]
There is an existing lock hierarchy of
&dev->event_lock --> &fasync_struct.fa_lock --> &f->f_owner.lock
from the following call chain:
input_inject_event():
spin_lock_irqsave(&dev->event_lock,...);
input_handle_event():
input_pass_values():
input_to_handler():
evdev_events():
evdev_pass_values():
spin_lock(&client->buffer_lock);
__pass_event():
kill_fasync():
kill_fasync_rcu():
read_lock(&fa->fa_lock);
send_sigio():
read_lock_irqsave(&fown->lock,...);
&dev->event_lock is HARDIRQ-safe, so interrupts have to be disabled
while grabbing &fasync_struct.fa_lock, otherwise we invert the lock
hierarchy. However, since kill_fasync which calls kill_fasync_rcu is
an exported symbol, it may not necessarily be called with interrupts
disabled.
As kill_fasync_rcu may be called with interrupts disabled (for
example, in the call chain above), we replace calls to
read_lock/read_unlock on &fasync_struct.fa_lock in kill_fasync_rcu
with read_lock_irqsave/read_unlock_irqrestore.
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 645ae0af18 ]
The function adf_iov_putmsg() is only used inside the intel_qat module
therefore should not be exported.
Remove EXPORT_SYMBOL for the function adf_iov_putmsg().
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b90c1c4d3f ]
At start and shutdown, VFs notify the PF about their state. These
notifications are carried out through a message exchange using the PFVF
protocol.
Function names lead to believe they do perform init or shutdown logic.
This is to fix the naming to better reflect their purpose.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a73c762e1 ]
The top half of the VF drivers handled only a source at the time.
If an interrupt for PF2VF and bundle occurred at the same time, the ISR
scheduled only the bottom half for PF2VF.
This patch fixes the VF top half so that if both sources of interrupt
trigger at the same time, both bottom halves are scheduled.
This patch is based on earlier work done by Conor McLoughlin.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5147f0906d ]
The function adf_dev_init() ignores the error code reported by
enable_vf2pf_comms(). If the latter fails, e.g. the VF is not compatible
with the pf, then the load of the VF driver progresses.
This patch changes adf_dev_init() so that the error code from
enable_vf2pf_comms() is returned to the caller.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe4d55773b ]
lockdep complains that in omap-aes, the list_lock is taken both with
softirqs enabled at probe time, and also in softirq context, which
could lead to a deadlock:
================================
WARNING: inconsistent lock state
5.14.0-rc1-00035-gc836005b01c5-dirty #69 Not tainted
--------------------------------
inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
ksoftirqd/0/7 [HC0[0]:SC1[3]:HE1:SE0] takes:
bf00e014 (list_lock){+.?.}-{2:2}, at: omap_aes_find_dev+0x18/0x54 [omap_aes_driver]
{SOFTIRQ-ON-W} state was registered at:
_raw_spin_lock+0x40/0x50
omap_aes_probe+0x1d4/0x664 [omap_aes_driver]
platform_probe+0x58/0xb8
really_probe+0xbc/0x314
__driver_probe_device+0x80/0xe4
driver_probe_device+0x30/0xc8
__driver_attach+0x70/0xf4
bus_for_each_dev+0x70/0xb4
bus_add_driver+0xf0/0x1d4
driver_register+0x74/0x108
do_one_initcall+0x84/0x2e4
do_init_module+0x5c/0x240
load_module+0x221c/0x2584
sys_finit_module+0xb0/0xec
ret_fast_syscall+0x0/0x2c
0xbed90b30
irq event stamp: 111800
hardirqs last enabled at (111800): [<c02a21e4>] __kmalloc+0x484/0x5ec
hardirqs last disabled at (111799): [<c02a21f0>] __kmalloc+0x490/0x5ec
softirqs last enabled at (111776): [<c01015f0>] __do_softirq+0x2b8/0x4d0
softirqs last disabled at (111781): [<c0135948>] run_ksoftirqd+0x34/0x50
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(list_lock);
<Interrupt>
lock(list_lock);
*** DEADLOCK ***
2 locks held by ksoftirqd/0/7:
#0: c0f5e8c8 (rcu_read_lock){....}-{1:2}, at: netif_receive_skb+0x6c/0x260
#1: c0f5e8c8 (rcu_read_lock){....}-{1:2}, at: ip_local_deliver_finish+0x2c/0xdc
stack backtrace:
CPU: 0 PID: 7 Comm: ksoftirqd/0 Not tainted 5.14.0-rc1-00035-gc836005b01c5-dirty #69
Hardware name: Generic AM43 (Flattened Device Tree)
[<c010e6e0>] (unwind_backtrace) from [<c010b9d0>] (show_stack+0x10/0x14)
[<c010b9d0>] (show_stack) from [<c017c640>] (mark_lock.part.17+0x5bc/0xd04)
[<c017c640>] (mark_lock.part.17) from [<c017d9e4>] (__lock_acquire+0x960/0x2fa4)
[<c017d9e4>] (__lock_acquire) from [<c0180980>] (lock_acquire+0x10c/0x358)
[<c0180980>] (lock_acquire) from [<c093d324>] (_raw_spin_lock_bh+0x44/0x58)
[<c093d324>] (_raw_spin_lock_bh) from [<bf00b258>] (omap_aes_find_dev+0x18/0x54 [omap_aes_driver])
[<bf00b258>] (omap_aes_find_dev [omap_aes_driver]) from [<bf00b328>] (omap_aes_crypt+0x94/0xd4 [omap_aes_driver])
[<bf00b328>] (omap_aes_crypt [omap_aes_driver]) from [<c08ac6d0>] (esp_input+0x1b0/0x2c8)
[<c08ac6d0>] (esp_input) from [<c08c9e90>] (xfrm_input+0x410/0x1290)
[<c08c9e90>] (xfrm_input) from [<c08b6374>] (xfrm4_esp_rcv+0x54/0x11c)
[<c08b6374>] (xfrm4_esp_rcv) from [<c0838840>] (ip_protocol_deliver_rcu+0x48/0x3bc)
[<c0838840>] (ip_protocol_deliver_rcu) from [<c0838c50>] (ip_local_deliver_finish+0x9c/0xdc)
[<c0838c50>] (ip_local_deliver_finish) from [<c0838dd8>] (ip_local_deliver+0x148/0x1b0)
[<c0838dd8>] (ip_local_deliver) from [<c0838f5c>] (ip_rcv+0x11c/0x180)
[<c0838f5c>] (ip_rcv) from [<c077e3a4>] (__netif_receive_skb_one_core+0x54/0x74)
[<c077e3a4>] (__netif_receive_skb_one_core) from [<c077e588>] (netif_receive_skb+0xa8/0x260)
[<c077e588>] (netif_receive_skb) from [<c068d6d4>] (cpsw_rx_handler+0x224/0x2fc)
[<c068d6d4>] (cpsw_rx_handler) from [<c0688ccc>] (__cpdma_chan_process+0xf4/0x188)
[<c0688ccc>] (__cpdma_chan_process) from [<c068a0c0>] (cpdma_chan_process+0x3c/0x5c)
[<c068a0c0>] (cpdma_chan_process) from [<c0690e14>] (cpsw_rx_mq_poll+0x44/0x98)
[<c0690e14>] (cpsw_rx_mq_poll) from [<c0780810>] (__napi_poll+0x28/0x268)
[<c0780810>] (__napi_poll) from [<c0780c64>] (net_rx_action+0xcc/0x204)
[<c0780c64>] (net_rx_action) from [<c0101478>] (__do_softirq+0x140/0x4d0)
[<c0101478>] (__do_softirq) from [<c0135948>] (run_ksoftirqd+0x34/0x50)
[<c0135948>] (run_ksoftirqd) from [<c01583b8>] (smpboot_thread_fn+0xf4/0x1d8)
[<c01583b8>] (smpboot_thread_fn) from [<c01546dc>] (kthread+0x14c/0x174)
[<c01546dc>] (kthread) from [<c010013c>] (ret_from_fork+0x14/0x38)
...
The omap-des and omap-sham drivers appear to have a similar issue.
Fix this by using spin_{,un}lock_bh() around device list access in all
the probe and remove functions.
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8617bb7400 ]
Tests showed a mismatch between what the CCA tool reports about
the APKA master key state and what's displayed by the zcrypt dd
in sysfs. After some investigation, we found out that the
documentation which was the source for the zcrypt dd implementation
lacks the listing of 3 fields. So this patch now moves the
evaluation of the APKA master key state to the correct offset.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3683c0552 ]
Introduce dev_busid, which exports the device-id associated with the
io-subchannel (and message-subchannel). The dev_busid indicates that of
the device which may be physically installed on the corrosponding
subchannel. The dev_busid value "none" indicates that the subchannel
is not valid, there is no I/O device currently associated with the
subchannel.
The dev_busid information would be helpful to write device-specific
udev-rules associated with the subchannel. The dev_busid interface would
be available even when the sch is not bound to any driver or if there is
no operational device connected on it. Hence this attribute can be used to
write udev-rules which are specific to the device associated with the
subchannel.
Signed-off-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit efe2175478 ]
Pin control needs to be activated by setting the enable bit, otherwise
hardware rejects all pin changes. Previously this stayed unnoticed on
Nexus 7 because pin control was enabled by default after rebooting from
downstream kernel, which uses driver that enables the bit and charger
registers are non-volatile until power supply (battery) is disconnected.
Configure the pin control enable bit. This fixes the potentially
never-enabled charging on devices that use pin control.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e804d5abe2 ]
According to the NVMe specification, the response dword 0 value of the
Connect command is based on status code: return cntlid for successful
compeltion return IPO and IATTR for connect invalid parameters. Fix
a missing error information for a zero sized queue, and return the
cntlid also for I/O queue Connect commands.
Signed-off-by: Amit Engel <amit.engel@dell.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 85032874f8 ]
We update ctrl->queue_count and schedule another reconnect when io queue
count is zero.But we will never try to create any io queue in next reco-
nnection, because ctrl->queue_count already set to zero.We will end up
having an admin-only session in Live state, which is exactly what we try
to avoid in the original patch.
Update ctrl->queue_count after queue_count zero checking to fix it.
Signed-off-by: Ruozhu Li <liruozhu@huawei.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 664227fde6 ]
We update ctrl->queue_count and schedule another reconnect when io queue
count is zero.But we will never try to create any io queue in next reco-
nnection, because ctrl->queue_count already set to zero.We will end up
having an admin-only session in Live state, which is exactly what we try
to avoid in the original patch.
Update ctrl->queue_count after queue_count zero checking to fix it.
Signed-off-by: Ruozhu Li <liruozhu@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f1e9630af ]
After patch 54efd50 (block: make generic_make_request handle
arbitrarily sized bios), the IO through io-throttle may be larger,
and these IOs may be further split into more small IOs. However,
IOPS throttle does not seem to be aware of this change, which
makes the calculation of IOPS of large IOs incomplete, resulting
in disk-side IOPS that does not meet expectations. Maybe we should
fix this problem.
We can reproduce it by set max_sectors_kb of disk to 128, set
blkio.write_iops_throttle to 100, run a dd instance inside blkio
and use iostat to watch IOPS:
dd if=/dev/zero of=/dev/sdb bs=1M count=1000 oflag=direct
As a result, without this change the average IOPS is 1995, with
this change the IOPS is 98.
Signed-off-by: Chunguang Xu <brookxu@tencent.com>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/65869aaad05475797d63b4c3fed4f529febe3c26.1627876014.git.brookxu@tencent.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28ce50f8d9 ]
Currently iocharset=utf8 mount option is broken. To use UTF-8 as iocharset,
it is required to use utf8 mount option.
Fix iocharset=utf8 mount option to use be equivalent to the utf8 mount
option.
If UTF-8 as iocharset is used then s_nls_iocharset is set to NULL. So
simplify code around, remove s_utf8 field as to distinguish between UTF-8
and non-UTF-8 it is needed just to check if s_nls_iocharset is set to NULL
or not.
Link: https://lore.kernel.org/r/20210808162453.1653-5-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b645333443 ]
Currently iocharset=utf8 mount option is broken. To use UTF-8 as iocharset,
it is required to use utf8 mount option.
Fix iocharset=utf8 mount option to use be equivalent to the utf8 mount
option.
If UTF-8 as iocharset is used then s_nls_map is set to NULL. So simplify
code around, remove UDF_FLAG_NLS_MAP and UDF_FLAG_UTF8 flags as to
distinguish between UTF-8 and non-UTF-8 it is needed just to check if
s_nls_map set to NULL or not.
Link: https://lore.kernel.org/r/20210808162453.1653-4-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 781d2a9a2f ]
We were checking validity of LVID entries only when getting
implementation use information from LVID in udf_sb_lvidiu(). However if
the LVID is suitably corrupted, it can cause problems also to code such
as udf_count_free() which doesn't use udf_sb_lvidiu(). So check validity
of LVID already when loading it from the disk and just disable LVID
altogether when it is not valid.
Reported-by: syzbot+7fbfe5fed73ebb675748@syzkaller.appspotmail.com
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c3b5e6ec0 ]
If high resolution timers are disabled the timerfd notification about a
clock was set event is not happening for all cases which use
clock_was_set_delayed() because that's a NOP for HIGHRES=n, which is wrong.
Make clock_was_set_delayed() unconditially available to fix that.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210713135158.196661266@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 627ef5ae2d ]
If __hrtimer_start_range_ns() is invoked with an already armed hrtimer then
the timer has to be canceled first and then added back. If the timer is the
first expiring timer then on removal the clockevent device is reprogrammed
to the next expiring timer to avoid that the pending expiry fires needlessly.
If the new expiry time ends up to be the first expiry again then the clock
event device has to reprogrammed again.
Avoid this by checking whether the timer is the first to expire and in that
case, keep the timer on the current CPU and delay the reprogramming up to
the point where the timer has been enqueued again.
Reported-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210713135157.873137732@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 406dd42bd1 ]
When an itimer deactivates a previously armed expiration, it simply doesn't
do anything. As a result the process wide cputime counter keeps running and
the tick dependency stays set until it reaches the old ghost expiration
value.
This can be reproduced with the following snippet:
void trigger_process_counter(void)
{
struct itimerval n = {};
n.it_value.tv_sec = 100;
setitimer(ITIMER_VIRTUAL, &n, NULL);
n.it_value.tv_sec = 0;
setitimer(ITIMER_VIRTUAL, &n, NULL);
}
Fix this with resetting the relevant base expiration. This is similar to
disarming a timer.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20210726125513.271824-4-frederic@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 767f4b620e ]
Hypervisors likely do not expose the SMCA feature to the guest and
loading this module leads to false warnings. This module should not be
loaded in guests to begin with, but people tend to do so, especially
when testing kernels in VMs. And then they complain about those false
warnings.
Do the practical thing and do not load this module when running as a
guest to avoid all that complaining.
[ bp: Rewrite commit message. ]
Suggested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Smita Koralahalli <Smita.KoralahalliChannabasappa@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Yazen Ghannam <yazen.ghannam@amd.com>
Tested-by: Kim Phillips <kim.phillips@amd.com>
Link: https://lkml.kernel.org/r/20210628172740.245689-1-Smita.KoralahalliChannabasappa@amd.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ccfc9dd691 ]
The soft watchdog timer function checks if a virtual machine
was suspended and hence what looks like a lockup in fact
is a false positive.
This is what kvm_check_and_clear_guest_paused() does: it
tests guest PVCLOCK_GUEST_STOPPED (which is set by the host)
and if it's set then we need to touch all watchdogs and bail
out.
Watchdog timer function runs from IRQ, so PVCLOCK_GUEST_STOPPED
check works fine.
There is, however, one more watchdog that runs from IRQ, so
watchdog timer fn races with it, and that watchdog is not aware
of PVCLOCK_GUEST_STOPPED - RCU stall detector.
apic_timer_interrupt()
smp_apic_timer_interrupt()
hrtimer_interrupt()
__hrtimer_run_queues()
tick_sched_timer()
tick_sched_handle()
update_process_times()
rcu_sched_clock_irq()
This triggers RCU stalls on our devices during VM resume.
If tick_sched_handle()->rcu_sched_clock_irq() runs on a VCPU
before watchdog_timer_fn()->kvm_check_and_clear_guest_paused()
then there is nothing on this VCPU that touches watchdogs and
RCU reads stale gp stall timestamp and new jiffies value, which
makes it think that RCU has stalled.
Make RCU stall watchdog aware of PVCLOCK_GUEST_STOPPED and
don't report RCU stalls when we resume the VM.
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4da13aa28 ]
A missing clock update is causing the following warning:
rq->clock_update_flags < RQCF_ACT_SKIP
WARNING: CPU: 112 PID: 2041 at kernel/sched/sched.h:1453
sub_running_bw.isra.0+0x190/0x1a0
...
CPU: 112 PID: 2041 Comm: sugov:112 Tainted: G W 5.14.0-rc1 #1
Hardware name: WIWYNN Mt.Jade Server System
B81.030Z1.0007/Mt.Jade Motherboard, BIOS 1.6.20210526 (SCP:
1.06.20210526) 2021/05/26
...
Call trace:
sub_running_bw.isra.0+0x190/0x1a0
migrate_task_rq_dl+0xf8/0x1e0
set_task_cpu+0xa8/0x1f0
try_to_wake_up+0x150/0x3d4
wake_up_q+0x64/0xc0
__up_write+0xd0/0x1c0
up_write+0x4c/0x2b0
cppc_set_perf+0x120/0x2d0
cppc_cpufreq_set_target+0xe0/0x1a4 [cppc_cpufreq]
__cpufreq_driver_target+0x74/0x140
sugov_work+0x64/0x80
kthread_worker_fn+0xe0/0x230
kthread+0x138/0x140
ret_from_fork+0x10/0x18
The task causing this is the `cppc_fie` DL task introduced by
commit 1eb5dde674 ("cpufreq: CPPC: Add support for frequency
invariance").
With CONFIG_ACPI_CPPC_CPUFREQ_FIE=y and schedutil cpufreq governor on
slow-switching system (like on this Ampere Altra WIWYNN Mt. Jade Arm
Server):
DL task `curr=sugov:112` lets `p=cppc_fie` migrate and since the latter
is in `non_contending` state, migrate_task_rq_dl() calls
sub_running_bw()->__sub_running_bw()->cpufreq_update_util()->
rq_clock()->assert_clock_updated()
on p.
Fix this by updating the clock for a non_contending task in
migrate_task_rq_dl() before calling sub_running_bw().
Reported-by: Bruno Goncalves <bgoncalv@redhat.com>
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Daniel Bristot de Oliveira <bristot@kernel.org>
Acked-by: Juri Lelli <juri.lelli@redhat.com>
Link: https://lore.kernel.org/r/20210804135925.3734605-1-dietmar.eggemann@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe28140b33 ]
We should not clear FLAGS_DMA_ACTIVE before omap_sham_update_dma_stop() is
done calling dma_unmap_sg(). We already clear FLAGS_DMA_ACTIVE at the
end of omap_sham_update_dma_stop().
The early clearing of FLAGS_DMA_ACTIVE is not causing issues as we do not
need to defer anything based on FLAGS_DMA_ACTIVE currently. So this can be
applied as clean-up.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Tero Kristo <kristo@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit caa534c3ba ]
When fuel_gauge_reg_readb()/_writeb() fails, report which register we
were trying to read / write when the error happened.
Also reword the message a bit:
- Drop the axp288 prefix, dev_err() already prints this
- Switch from telegram / abbreviated style to a normal sentence, aligning
the message with those from fuel_gauge_read_*bit_word()
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f95091536f ]
It is possible for sched_getattr() to incorrectly report the state of
the reset_on_fork flag when called on a deadline task.
Indeed, if the flag was set on a deadline task using sched_setattr()
with flags (SCHED_FLAG_RESET_ON_FORK | SCHED_FLAG_KEEP_PARAMS), then
p->sched_reset_on_fork will be set, but __setscheduler() will bail out
early, which means that the dl_se->flags will not get updated by
__setscheduler_params()->__setparam_dl(). Consequently, if
sched_getattr() is then called on the task, __getparam_dl() will
override kattr.sched_flags with the now out-of-date copy in dl_se->flags
and report the stale value to userspace.
To fix this, make sure to only copy the flags that are relevant to
sched_deadline to and from the dl_se->flags field.
Signed-off-by: Quentin Perret <qperret@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20210727101103.2729607-2-qperret@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df6313d707 ]
After calling dma_map_single(), we must also call dma_mapping_error().
This fixes the following warning when compiling with CONFIG_DMA_API_DEBUG:
[ 311.241478] WARNING: CPU: 0 PID: 428 at kernel/dma/debug.c:1027 check_unmap+0x79c/0x96c
[ 311.249547] DMA-API: mxs-dcp 2280000.crypto: device driver failed to check map error[device address=0x00000000860cb080] [size=32 bytes] [mapped as single]
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 048661a1f9 ]
Yanfei reported that setting HANDOFF should not depend on recomputing
@first, only on @first state. Which would then give:
if (ww_ctx || !first)
first = __mutex_waiter_is_first(lock, &waiter);
if (first)
__mutex_set_flag(lock, MUTEX_FLAG_HANDOFF);
But because 'ww_ctx || !first' is basically 'always' and the test for
first is relatively cheap, omit that first branch entirely.
Reported-by: Yanfei Xu <yanfei.xu@windriver.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Waiman Long <longman@redhat.com>
Reviewed-by: Yanfei Xu <yanfei.xu@windriver.com>
Link: https://lore.kernel.org/r/20210630154114.896786297@infradead.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a729691b54 upstream.
When this platform was relatively new in November 2011, with early BIOS
revisions, a reboot quirk was added in commit 6be30bb7d7 ("x86/reboot:
Blacklist Dell OptiPlex 990 known to require PCI reboot")
However, this quirk (and several others) are open-ended to all BIOS
versions and left no automatic expiry if/when the system BIOS fixed the
issue, meaning that nobody is likely to come along and re-test.
What is really problematic with using PCI reboot as this quirk does, is
that it causes this platform to do a full power down, wait one second,
and then power back on. This is less than ideal if one is using it for
boot testing and/or bisecting kernels when legacy rotating hard disks
are installed.
It was only by chance that the quirk was noticed in dmesg - and when
disabled it turned out that it wasn't required anymore (BIOS A24), and a
default reboot would work fine without the "harshness" of power cycling the
machine (and disks) down and up like the PCI reboot does.
Doing a bit more research, it seems that the "newest" BIOS for which the
issue was reported[1] was version A06, however Dell[2] seemed to suggest
only up to and including version A05, with the A06 having a large number of
fixes[3] listed.
As is typical with a new platform, the initial BIOS updates come frequently
and then taper off (and in this case, with a revival for CPU CVEs); a
search for O990-A<ver>.exe reveals the following dates:
A02 16 Mar 2011
A03 11 May 2011
A06 14 Sep 2011
A07 24 Oct 2011
A10 08 Dec 2011
A14 06 Sep 2012
A16 15 Oct 2012
A18 30 Sep 2013
A19 23 Sep 2015
A20 02 Jun 2017
A23 07 Mar 2018
A24 21 Aug 2018
While it's overkill to flash and test each of the above, it would seem
likely that the issue was contained within A0x BIOS versions, given the
dates above and the dates of issue reports[4] from distros. So rather than
just throw out the quirk entirely, limit the scope to just those early BIOS
versions, in case people are still running systems from 2011 with the
original as-shipped early A0x BIOS versions.
[1] https://lore.kernel.org/lkml/1320373471-3942-1-git-send-email-trenn@suse.de/
[2] https://www.dell.com/support/kbdoc/en-ca/000131908/linux-based-operating-systems-stall-upon-reboot-on-optiplex-390-790-990-systems
[3] https://www.dell.com/support/home/en-ca/drivers/driversdetails?driverid=85j10
[4] https://bugs.launchpad.net/ubuntu/+source/linux/+bug/768039
Fixes: 6be30bb7d7 ("x86/reboot: Blacklist Dell OptiPlex 990 known to require PCI reboot")
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210530162447.996461-4-paul.gortmaker@windriver.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c8774a94e upstream.
User space could ask for very large hash tables, we need to make sure
our size computations wont overflow.
nf_tables_newset() needs to double check the u64 size
will fit into size_t field.
Fixes: 0ed6389c48 ("netfilter: nf_tables: rename set implementations")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a9ed27a764 upstream.
is_flush_rq() is called from bt_iter()/bt_tags_iter(), and runs the
following check:
hctx->fq->flush_rq == req
but the passed hctx from bt_iter()/bt_tags_iter() may be NULL because:
1) memory re-order in blk_mq_rq_ctx_init():
rq->mq_hctx = data->hctx;
...
refcount_set(&rq->ref, 1);
OR
2) tag re-use and ->rqs[] isn't updated with new request.
Fix the issue by re-writing is_flush_rq() as:
return rq->end_io == flush_end_io;
which turns out simpler to follow and immune to data race since we have
ordered WRITE rq->end_io and refcount_set(&rq->ref, 1).
Fixes: 2e315dc07d ("blk-mq: grab rq->refcount before calling ->fn in blk_mq_tagset_busy_iter")
Cc: "Blank-Burian, Markus, Dr." <blankburian@uni-muenster.de>
Cc: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20210818010925.607383-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Cc: Yi Zhang <yi.zhang@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2da19ed50 upstream.
For fixing use-after-free during iterating over requests, we grabbed
request's refcount before calling ->fn in commit 2e315dc07d ("blk-mq:
grab rq->refcount before calling ->fn in blk_mq_tagset_busy_iter").
Turns out this way may cause kernel panic when iterating over one flush
request:
1) old flush request's tag is just released, and this tag is reused by
one new request, but ->rqs[] isn't updated yet
2) the flush request can be re-used for submitting one new flush command,
so blk_rq_init() is called at the same time
3) meantime blk_mq_queue_tag_busy_iter() is called, and old flush request
is retrieved from ->rqs[tag]; when blk_mq_put_rq_ref() is called,
flush_rq->end_io may not be updated yet, so NULL pointer dereference
is triggered in blk_mq_put_rq_ref().
Fix the issue by calling refcount_set(&flush_rq->ref, 1) after
flush_rq->end_io is set. So far the only other caller of blk_rq_init() is
scsi_ioctl_reset() in which the request doesn't enter block IO stack and
the request reference count isn't used, so the change is safe.
Fixes: 2e315dc07d ("blk-mq: grab rq->refcount before calling ->fn in blk_mq_tagset_busy_iter")
Reported-by: "Blank-Burian, Markus, Dr." <blankburian@uni-muenster.de>
Tested-by: "Blank-Burian, Markus, Dr." <blankburian@uni-muenster.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/20210811142624.618598-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Cc: Yi Zhang <yi.zhang@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e10de31428 upstream.
On certain AMD platforms, when the IOMMU performance counter source
(csource) field is zero, power-gating for the counter is enabled, which
prevents write access and returns zero for read access.
This can cause invalid perf result especially when event multiplexing
is needed (i.e. more number of events than available counters) since
the current logic keeps track of the previously read counter value,
and subsequently re-program the counter to continue counting the event.
With power-gating enabled, we cannot gurantee successful re-programming
of the counter.
Workaround this issue by :
1. Modifying the ordering of setting/reading counters and enabing/
disabling csources to only access the counter when the csource
is set to non-zero.
2. Since AMD IOMMU PMU does not support interrupt mode, the logic
can be simplified to always start counting with value zero,
and accumulate the counter value when stopping without the need
to keep track and reprogram the counter with the previously read
counter value.
This has been tested on systems with and without power-gating.
Fixes: 994d6608ef ("iommu/amd: Remove performance counter pre-initialization test")
Suggested-by: Alexander Monakov <amonakov@ispras.ru>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20210504065236.4415-1-suravee.suthikulpanit@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f99185041 upstream.
With commit 439c7183e5 ("serial: 8250: 8250_omap: Disable RX interrupt after DMA enable"),
below warning is seen with W=1 and CONFIG_SERIAL_8250_DMA is disabled:
drivers/tty/serial/8250/8250_omap.c:1199:42: warning: unused variable 'k3_soc_devices' [-Wunused-const-variable]
Fix this by moving the code using k3_soc_devices array to
omap_serial_fill_features_erratas() that handles other errata flags as
well.
Fixes: 439c7183e5 ("serial: 8250: 8250_omap: Disable RX interrupt after DMA enable")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20201111112653.2710-2-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ad69832f3 upstream.
When we free a page whose order is very close to MAX_ORDER and greater
than pageblock_order, it wastes some CPU cycles to increase max_order to
MAX_ORDER one by one and check the pageblock migratetype of that page
repeatedly especially when MAX_ORDER is much larger than pageblock_order.
We also should not be checking migratetype of buddy when "order ==
MAX_ORDER - 1" as the buddy pfn may be invalid, so adjust the condition.
With the new check, we don't need the max_order check anymore, so we
replace it.
Also adjust max_order initialization so that it's lower by one than
previously, which makes the code hopefully more clear.
Link: https://lkml.kernel.org/r/20201204155109.55451-1-songmuchun@bytedance.com
Fixes: d9dddbf556 ("mm/page_alloc: prevent merging between isolated and other pageblocks")
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 161a582bd1 upstream.
clang static analysis reports this problem
mos7720.c:352:2: warning: Undefined or garbage value returned to caller
return d;
^~~~~~~~
In the parport_mos7715_read_data()'s call to read_mos_reg(), 'd' is
only set after the alloc block.
buf = kmalloc(1, GFP_KERNEL);
if (!buf)
return -ENOMEM;
Although the problem is reported in parport_most7715_read_data(),
none of the callee's of read_mos_reg() check the return status.
Make sure to clear the return-value buffer also on allocation failures.
Fixes: 0d130367ab ("USB: serial: mos7720: fix control-message error handling")
Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20210111220904.1035957-1-trix@redhat.com
[ johan: only clear the buffer on errors, amend commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This repository contains the Linux kernel used on the Raspberry Pi. If you believe that the issue you are seeing is kernel-related, this is the right place. If not, we have other repositories for the GPU firmware at [github.com/raspberrypi/firmware](https://github.com/raspberrypi/firmware) and Raspberry Pi userland applications at [github.com/raspberrypi/userland](https://github.com/raspberrypi/userland). If you have problems with the Raspbian distribution packages, report them in the [github.com/RPi-Distro/repo](https://github.com/RPi-Distro/repo). If you simply have a question, then [the Raspberry Pi forums](https://www.raspberrypi.org/forums) are the best place to ask it.
**Describe the bug**
Add a clear and concise description of what you think the bug is.
**To reproduce**
List the steps required to reproduce the issue.
**Expected behaviour**
Add a clear and concise description of what you expected to happen.
**Actual behaviour**
Add a clear and concise description of what actually happened.
**System**
Copy and paste the results of the raspinfo command in to this section. Alternatively, copy and paste a pastebin link, or add answers to the following questions:
* Which model of Raspberry Pi? e.g. Pi3B+, PiZeroW
* Which OS and version (`cat /etc/rpi-issue`)?
* Which firmware version (`vcgencmd version`)?
* Which kernel version (`uname -a`)?
**Logs**
If applicable, add the relevant output from `dmesg` or similar.
description:Create a report to help us fix your issue
body:
- type:markdown
attributes:
value:|
**Is this the right place for my bug report?**
This repository contains the Linux kernel used on the Raspberry Pi.
If you believe that the issue you are seeing is kernel-related, this is the right place.
If not, we have other repositories for the GPU firmware at [github.com/raspberrypi/firmware](https://github.com/raspberrypi/firmware) and Raspberry Pi userland applications at [github.com/raspberrypi/userland](https://github.com/raspberrypi/userland).
If you have problems with the Raspbian distribution packages, report them in the [github.com/RPi-Distro/repo](https://github.com/RPi-Distro/repo).
If you simply have a question, then [the Raspberry Pi forums](https://www.raspberrypi.org/forums) are the best place to ask it.
- type:textarea
id:description
attributes:
label:Describe the bug
description:|
Add a clear and concise description of what you think the bug is.
validations:
required:true
- type:textarea
id:reproduce
attributes:
label:Steps to reproduce the behaviour
description:|
List the steps required to reproduce the issue.
validations:
required:true
- type:dropdown
id:model
attributes:
label:Device (s)
description:Onwhich device you are facing the bug?
multiple:true
options:
- Raspberry Pi Zero
- Raspberry Pi Zero W/WH
- Raspberry Pi Zero 2 W
- Raspberry Pi 1 Mod. A
- Raspberry Pi 1 Mod. A+
- Raspberry Pi 1 Mod. B
- Raspberry Pi 1 Mod. B+
- Raspberry Pi 2 Mod. B
- Raspberry Pi 2 Mod. B v1.2
- Raspberry Pi 3 Mod. A+
- Raspberry Pi 3 Mod. B
- Raspberry Pi 3 Mod. B+
- Raspberry Pi 4 Mod. B
- Raspberry Pi 400
- Raspberry Pi CM1
- Raspberry Pi CM3
- Raspberry Pi CM3 Lite
- Raspberry Pi CM3+
- Raspberry Pi CM3+ Lite
- Raspberry Pi CM4
- Raspberry Pi CM4 Lite
- Other
validations:
required:true
- type:textarea
id:system
attributes:
label:System
description:|
Copy and paste the results of the raspinfo command in to this section.
Alternatively, copy and paste a pastebin link, or add answers to the following questions:
* Which OS and version (`cat /etc/rpi-issue`)?
* Which firmware version (`vcgencmd version`)?
* Which kernel version (`uname -a`)?
validations:
required:true
- type:textarea
id:logs
attributes:
label:Logs
description:|
If applicable, add the relevant output from `dmesg` or similar.
about:"Please do not use GitHub for asking questions. If you simply have a question, then the Raspberry Pi forums are the best place to ask it. Thanks in advance for helping us keep the issue tracker clean!"
- name:"⛔ Problems with the Raspbian distribution packages"
url:https://github.com/RPi-Distro/repo
about:"If you have problems with the Raspbian distribution packages, please report them in the github.com/RPi-Distro/repo."
audio Enable or disable audio over HDMI (default "on")
noaudio Disable all HDMI audio (default "off")
nocomposite Disable the composite video output (default
"off")
composite Enable the composite output (default "off")
N.B. Disables all other outputs on a Pi 4.
Name: vc4-kms-v3d-pi4
@@ -3511,6 +3731,14 @@ Load: dtoverlay=vga666
Params: <None>
Name: vl805
Info: Overlay to enable a VIA VL805 USB3 controller on CM4 carriers
Will be loaded automatically by up-to-date firmware if "VL805=1" is
set in the EEPROM config.
Load: dtoverlay=vl805
Params: <None>
Name: w1-gpio
Info: Configures the w1-gpio Onewire interface module.
Use this overlay if you *don't* need a GPIO to drive an external pullup.
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
