Enable PDAF output for all modes, and also need to modify Embedded Line
Width to 11560 * 3 (two lines of Embedded Data + one line of PDAF).
Signed-off-by: Lee Jackson <lee.jackson@arducam.com>
Arducam 64MP has specific requirements for the line length, and if these
conditions are not met, the camera will not function properly. Under the
previous configuration, once a stream off operation is performed, the
camera will not output any data, even if a stream on operation is
performed. This prevents us from switching from 1280x720 to another
resolution.
Signed-off-by: Lee Jackson <lee.jackson@arducam.com>
commit 4e08713336 upstream.
According to CTA 861 the channel/speaker allocation info in the
audio infoframe only applies to uncompressed (PCM) audio streams.
The channel count info should indicate the number of channels
in the transmitted audio, which usually won't match the number of
channels used to transmit the compressed bitstream.
Some devices (eg some Sony TVs) will refuse to decode compressed
audio if these values are not set correctly.
To fix this we can simply set the channel count to 0 (which means
"refer to stream header") and set the channel/speaker allocation to 0
as well (which would mean stereo FL/FR for PCM, a safe value all sinks
will support) when transmitting compressed audio.
Signed-off-by: Matthias Reichl <hias@horus.com>
Link: https://lore.kernel.org/r/20230624165232.5751-1-hias@horus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
commit 04b49b90ca upstream.
The SADs of compressed formats contain the channel and sample rate
info of the audio data inside the compressed stream, but when
building constraints we must use the rates and channels used to
transport the compressed streams.
eg 48kHz 6ch EAC3 needs to be transmitted as a 2ch 192kHz stream.
This patch fixes the constraints for the common AC3 and DTS formats,
the constraints for the less common MPEG, DSD etc formats are copied
directly from the info in the SADs as before as I don't have the specs
and equipment to test those.
Signed-off-by: Matthias Reichl <hias@horus.com>
Link: https://lore.kernel.org/r/20230624165216.5719-1-hias@horus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a speed parameter to the jedec-spi-nor overlay to allow much
faster accesses, taking the opportunity to simplify the internals.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
In converting to using the standard u16_fract type, commit [1] made the
obvious mistake and failed to take account of the difference in
numerator and denominator ordering, breaking all uses of the cs43130
codec.
Fix it.
[1] commit e14bd35ef4 ("ASoC: cs43130: Re-use generic struct u16_fract")
Fixes: e14bd35ef4 ("ASoC: cs43130: Re-use generic struct u16_fract")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The overlays configured both irq-gpio and an interrupts/
interrupt-parent configuration for the stmpe MFD device.
irq-gpio was reworked in 6.1 and has issues with the configuration
as provided. Removing it and using the interrupts/interrupt-parent
configuration works fine, so do that.
See: https://forums.raspberrypi.com/viewtopic.php?t=351394
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Ensure that the frame sequence counter is incremented only if a previous
frame start interrupt has occurred, or a frame start + frame end has
occurred simultaneously.
This corresponds the sequence number with the actual number of frames
produced by the sensor, not the number of frame buffers dequeued back
to userland.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
At a high FPS with RAW10, there is frame corruption for 480p because the
rate_factor of 2 is used with the normal 2x2 bining [1]. This commit
ties the rate_factor to the selected binning mode. For the 480p mode,
analog 2x2 binning mode with a rate_factor of 2 is always used. For the
1232p mode the normal 2x2 binning mode is used for RAW10 while analog
2x2 binning mode is used for RAW8.
[1] https://github.com/raspberrypi/linux/issues/5493
Signed-off-by: Vinay Varma <varmavinaym@gmail.com>
A DSI write is issued in st7701_prepare even when the probed panel
runs on SPI. In practice, this results in a panic with the
vc4-kms-dpi-hyperpixel2r overlay active.
Perform the equivalent write over SPI in this case.
Signed-off-by: Jack Andersen <jackoalan@gmail.com>
Disable enumerating and setting of the 2x2 binned mode entirely as it
does not seem to work for either mono or colour sensor variants.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
There is a problem with the current abort scheme
when dma is blocked on a DREQ which prevents halting.
This is triggered by SPI driver which aborts dma
in this state and so leads to a halt timeout.
Discussion with Broadcom suggests the sequence:
CS.ACTIVE=0
while (CS.OUTSTANDING_TRANSACTIONS == 0)
wait()
DEBUG.RESET=1
should be safe on a dma40 channel.
Unfortunately the non-dma40 channels don't have
OUTSTANDING_TRANSACTIONS, so we need a more
complicated scheme.
We attempt to abort the channel, which will work
if there is no blocked DREQ.
It it times out, we can assume there is no AXI
transfer in progress and reset anyway.
The length of the timeout is observed at ~20us.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
As of [1], using PPS_FETCH on a 64-bit ARM kernel with a 32-bit userland
is broken, returning a timeout. This is because the requested 4-byte
alignment for struct pps_ktime_compat (illegal on arm64) results in the
timeout flags field being uninitialised.
Make the hack specific to X86_64 builds with CONFIG_COMPAT defined.
[1] commit c2a49fe8ee ("pps: fix padding issue with PPS_FETCH for
ioctl_compat")
See: https://github.com/raspberrypi/linux/issues/5430
Fixes: c2a49fe8ee ("pps: fix padding issue with PPS_FETCH for ioctl_compat")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Now that transfers aren't aborted immediately (and uncleanly) on
errors, and the FIFOs are always drained after all transfers, we
can implement I2C_M_IGNORE_NAK by ignoring the returned error
value.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
If a transaction is aborted immediately on ERR being reported,
then the bus is not returned to the STOP condition, and devices
generally get very upset.
Handle the ERR and CLKT conditions only when TA is not set.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
On error condition, note the error return code, but still
handle the FIFOs in the normal way rather than relying on
C_CLEAR flushing everything cleanly.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Rather than always reading the maximum number of points supported
by the chip (which may be as high as 10), read the number of
active points first, and read data for just those.
In most cases this will result in less data on the I2C bus,
with only the maximum touch points taking more due to a second
read that has to configure the start address.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Rather than deleting the upstream stdout-path declaration, overwrite
it with one selecting serial0, which will always be the UART mapped
to the 40-pin header (provided enable_uart=1 is specified). Doing
so has the advantage that earlycon can be configured just by adding
"earlycon" to the command line.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The arm64 initialisation uses the physical address reachable by all
DMA controllers to set the size of ZONE_DMA. This fails on BCM2711
with the current dts files because the declaration of the I/O space
fools it into thinking the legacy 30-bit DMA channels can see most
of the 32-bit space.
Take advantage of the simple nature of the implementation by adding
a node with a restricted dma-ranges property solely so to act as the
limiting factor in the calculation.
See: https://github.com/raspberrypi/linux/issues/5470
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Now we wait for write responses and have a burst
size of 4, we can set the fifo threshold much higher.
Set it to 28 (of the 32 entry size) to keep fifo
fuller and reduce chance of underflow.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Also tweak the flags:
Remove NO_WAIT_RESP (27)
Add BURST_LENGTH (30)
The AXI path from DMA controller to HDMI audio fifo
is long, and may have considerable delay.
When using DMA without waiting for responses it is
very easy to overfill the fifo as when the fifo
removes DREQ there may be large numbers of writes
in flight.
This means the DREQ fifo threshold must be set low
enough to accommodate the maximum number of in flight
writes (unknown by something like 24),
which means the 32 element fifo only requests data
when it contains fewer than 8 entries, making it
susceptable to underflow.
If we wait for write responses we can set the DREQ
fifo threshold much higher as there are a controlled
number of writes in flight.
However the overall bandwidth is reduced by setting
this, so also enable a burstsize of 4 to improve
bandwidth.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Add a control bit to enable a multi-beat burst on a DMA.
This improves DMA performance and is required for HDMI audio.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
The sequence we were doing was not safe.
Clearing CS meant BCM2835_DMA_WAIT_FOR_WRITES was cleared
and so polling BCM2835_DMA_WAITING_FOR_WRITES has no benefit
Broadcom have provided a recommended sequence to abort
a dma lite channel, so switch to that.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
It wasn't aborting the transfer and caused stop/start
of hdmi audio dma to be unreliable.
New sequence approved by Broadcom.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
The bcm2835_dma_create_cb_chain() function is in charge of building up
the descriptors chain for a given transfer.
It was initially supporting only the BCM2835-style DMA controller, and
was later expanded to support controllers with 40-bits channels that use
a different descriptor layout.
However, some part of the function only use the old style descriptor,
even when building a chain of new-style descriptors, resulting in weird
bugs.
Fixes: 9a52a99183 ("bcm2835-dma: Add proper 40-bit DMA support")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
bcm2711_dma40_memcpy has some code strictly equivalent to the
to_bcm2711_cbaddr() function. Let's use it instead.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
For 40 bits channels, the position is reported by reading the upper byte
in the SRCI/DESTI registers. However the driver adds that upper byte
with an 8-bits left shift, while it should be 32.
Fixes: 9a52a99183 ("bcm2835-dma: Add proper 40-bit DMA support")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Add an i2s_dma4 parameter to make the I2S interface use 40-bit DMA
channels, taking the opportunity to remove some duplication.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Contrary to what struct snd_dmaengine_dai_dma_data suggests, the
configuration of addresses of DMA slave interfaces should be done in
CPU physical addresses.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Contrary to what struct snd_dmaengine_dai_dma_data suggests, the
configuration of addresses of DMA slave interfaces should be done in
CPU physical addresses.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Contrary to what struct snd_dmaengine_dai_dma_data suggests, the
configuration of addresses of DMA slave interfaces should be done in
CPU physical addresses.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Although the system timer is largely ignored in favour of the ARM local
timers, retain the DT node so that the bcm2835-sdhost logging can find
the timer in a cleaner fashion.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Contrary to what struct snd_dmaengine_dai_dma_data suggests, the
configuration of addresses of DMA slave interfaces should be done in
CPU physical addresses.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Contrary to what struct snd_dmaengine_dai_dma_data suggests, the
configuration of addresses of DMA slave interfaces should be done in
CPU physical addresses.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Slave addresses for DMA are meant to be supplied as physical addresses
(contrary to what struct snd_dmaengine_dai_dma_data does).
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Contrary to what struct snd_dmaengine_dai_dma_data suggests, the
configuration of addresses of DMA slave interfaces should be done in
CPU physical addresses.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Slave addresses for DMA are meant to be supplied as physical addresses
(contrary to what struct snd_dmaengine_dai_dma_data does). It is up to
the DMA controller driver to perform the translation based on its own
view of the world, as described in Device Tree.
Now that the Pi Device Trees have the correct peripheral mappings,
replace the hacky address munging with phys_to_dma().
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Step one of using DMA addresses the intended way is to make sure that
the mapping between CPU physical addresses and DMA addresses in Device
Tree is complete and correct.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Two new debugfs interfaces are implemented:
- gpu_usage: exposes the total runtime since boot of each
of the 5 scheduling queues available at V3D (BIN, RENDER,
CSD, TFU, CACHE_CLEAN). So if the interface is queried at
two different points of time the usage percentage of each
of the queues can be calculated.
- gpu_pid_usage: exposes the same information but to the
level of detail of each process using the V3D driver. The
runtime for process using the driver is stored. So the
percentages of usage by PID can be calculated with
measures at different timestamps.
The storage of gpu_pid_usage stats is only done if
the debugfs interface is polled during the last 70 seconds.
If a process does not submit a GPU job during last 70
seconds its stats will also be purged.
Signed-off-by: Jose Maria Casanova Crespo <jmcasanova@igalia.com>
It has been observed that edge events can be lost when GPIO edges occur
close to each other. Investigation suggests this is due to a hardware
bug, although no mechanism has been identified.
Work around the event loss by moving the IRQ acknowledgement into the
main ISR, adding missing events by explicit level-change detection.
See: https://forums.raspberrypi.com/viewtopic.php?t=350295
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Now that the kernel controls the onboard Bluetooth initialisation by
default, the miniuart-bt overlay needs updating to match.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Change the base Device Tree files so that by default the kernel is
responsible for initialisation of the onboard Bluetooth modems.
Use dtparam=krnbt=off to revert to the old behaviour.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The kernel needs to recognise the default BDADDRs used by the Bluetooth
modems, so add a few more that we care about.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The kernel Bluetooth framework understands that devices may not
be programmed with valid Bluetooth addresses. It also has the ability
to override a Bluetooth address with the value of the local-bd-address
DT property, but it ignores the validity of the existing address when
doing so.
Add a new boolean property, fallback-bd-address, which indicates that
the given local-bd-address property should only be used if the device
does not already have a valid BDADDR.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The BCM2835 mini-UART has no modem status interrupt, causing all
transmission to stop, never to use, if a speed change ever happens
while the CTS signal is high.
Add a simple polling mechanism in order to allow recovery in that
situation.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Pi 0-3 have no deep colour support and only 24bpp output,
so max_bpc should remain as 8.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
There is no DT binding for emc2305 as mainline are still
discussing how to do a generic fan binding.
The 5.15 driver was reading the "emc2305," properties
"cooling-levels", "pwm-max", "pwm-min", and "pwm-channel" as u8.
The overlay was writing them as u16 (;) so it was working.
The 6.1 driver was reading as u32, which failed as there is
insufficient data.
As this is all downstream only, revert to u8 to match 5.15.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The i2c-pwm-pca9685a overlay was fixed to i2c-1. Add overrides to allow
it to be assigned to alternate buses.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The i2c-mux overlay was fixed to i2c-1. Add overrides to allow
it to be assigned to alternate buses.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
There is an off-by-one error in the default brightness for the PWM backlight
in the MIPI DBI SPI overlay that produces the following message in the
kernel logs:
pwm-backlight backlight_pwm: invalid default brightness level: 16, using 15
The value is 0-based, so the max brightness is 15, not 16.
Signed-off-by: David Lechner <david@lechnology.com>
They come in varying sizes, but all have the same MCU for
power control and touch controller.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The interrupt line from the touch controller is not necessarily
connected to the SoC, so add the option to poll for touch info.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Waveshare sell a range of DSI panels of varying sizes, all
using a common MCU to control the panel and backlight.
Add a panel driver that supports these panels.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Commit 46ef9d4ed2 ("hwmon: emc2305: fixups for driver submitted to
mailing lists") missed adding the call to thermal_of_cooling_device_register
required to configure any cooling maps for the device, hence stopping it
from actually ever changing speed.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The 640x480 mode uses a special binning mode for high framerate operation where
the pixel rate is effectively doubled. Account for this when setting up the
pixel clock rate, and applying the vblank and exposure controls.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
This reverts commit 947ba6e85e.
Since [1], the clock driver has automatically rounded up the
UART clock frequency, so this patch is no longer needed.
[1] f690a4d7a8 ("clk: bcm2835: Round UART input clock up")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
We believe the OOM issue with MGLRU on 32-bit kernel
only affects Pi4 which uses CONFIG_VMSPLIT_3G.
Pi0-3 which use CONFIG_VMSPLIT_2G is expected not to
suffer from this OOM issue.
So lets enable MGLRU by default for these users,
who many benefit from the advantages it has.
See: https://github.com/raspberrypi/linux/issues/5395
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Complete USB Gadget Support to bcmrpi3_defconfig
Cross-referenced with bcm2711_defconfig to include the same USB gadgets. Adds support for the Pi 3 and derivative devices (BCM2837) such as the Pi Zero 2 W.
See: https://github.com/raspberrypi/linux/pull/5427
Since there is now a dedicated dts file for the rev1 Model B (the only
Pi to drive the primary camera with i2c1), move the creation of the
i2c_arm, i2c_vc and i2c labels, aliases and overrides into the base dts
files.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The patch adding image encode (JPEG) to the driver missed adding
the alignment constraint for V4L2_PIX_FMT_RGBA32, which meant
it ended up giving a stride and size of 0.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Sinc [1] uaccess_with_memcpy.c uses __memcpy instead of memcpy. Make
the optimised memcpy available as __memcpy as well to avoid linkage
failures.
[1] ceac10c83b ("ARM: 9290/1: uaccess: Fix KASAN false-positives")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The kernel's time unit of jiffies should be stored as an unsigned long
value. Storing it as an unsigned int, as gpio-fsm did, leads to
truncation and malfunction when the kernel is built for a 64-bit
platform.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
media_pipeline_start and media_pipeline_stop now validate that
the pipeline is being started and stopped with the same pipe
and pad handles.
When running with embedded metadata (eg imx477 and imx708), the
start typically happens from the metadata pad, whilst stop is
always from the image pad.
Always pass the image pad to media_pipeline_start to ensure
that the calls are balanced.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Create a cluster for the HVLIP and VFLIP controls so they are treated
as a single composite control.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Switch the system clock name from "xclk" to "inclk".
Use lower case lables for all regulator names.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Switch the system clock name from "xclk" to "inclk".
Use lower case lables for all regulator names.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Replace the existing imx708.yaml file with sony,imx708.yaml that follows
the latest devicetree conventions for camera sensors.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
This commit addresses vaious tidy-ups requesed for upstreaming the
IMX708 driver. Notably:
- Remove #define IMX708_NUM_SUPPLIES and use ARRAY_SIZE() directly
- Use dev_err_probe where possible in imx708_probe()
- Fix error handling paths in imx708_probe()
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Add a parameter to change the sensor device CSI-2 link frequency to
one of the following values: 450Mhz (default), 447Mhz, or 453Mhz.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Add support for three different usable link frequencies (default 450Mhz,
447Mhz, and 453MHz) for the IMX708 camera sensor. The choice of
frequency is handled thorugh the "link-frequency" overlay parameter.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Setting both the Drop and Add bits on the input context prevents the
corruption of split transactions seen with the BCM2711 XHCI controller,
which is a dwc3 variant.
This is a downstream feature that allows usbhid to restrict polling
intervals on mice and keyboards, and was only tested on a VL805 which
didn't complain about the fact the endpoint got added twice.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Since [1], the fbdev deferred IO framework is careful to cancel
pending updates on close to prevent dirty pages being accessed after
they may have been reused. However, this is not necessary in the case
that the pagelist is empty, and drivers that don't make use of the
pagelist may have wanted updates cancelled for no good reason.
Avoid penalising fbdev drivers that don't make use of the pagelist by
making the cancelling of deferred IO on close conditional on there
being a non-empty pagelist.
See: https://github.com/raspberrypi/linux/issues/5398
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
[1] 3efc61d952 ("fbdev: Fix invalid page access after closing deferred I/O devices")
Now upstream have accepted patches adding a mono version of
IMX290, and IMX327, update the compatible strings in the overlays
to match.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The new ssd130x DRM driver supports both SSD1306 I2C and SPI panels and is
compatible with the ssd1307fb driver bindings. So the "solomon,com-invdir"
DT property (to invert the COM pin scan dir) can also be used for SPI now.
This allows to configure panels whose scan direction needs to be inverted.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
For H264, V4L2_CID_MPEG_VIDEO_H264_I_PERIOD is meant to be the intra
I-frame period, whilst V4L2_CID_MPEG_VIDEO_GOP_SIZE is the intra IDR
frame period.
The firmware encoder doesn't produce I-frames that aren't IDR as well,
therefore V4L2_CID_MPEG_VIDEO_GOP_SIZE is technically the correct
control, however users may have adopted V4L2_CID_MPEG_VIDEO_H264_I_PERIOD.
Add support for V4L2_CID_MPEG_VIDEO_GOP_SIZE controlling the encoder,
and have VIDIOC_S_CTRL for V4L2_CID_MPEG_VIDEO_H264_I_PERIOD update
the value for V4L2_CID_MPEG_VIDEO_GOP_SIZE (the reverse is not
implemented).
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
FFmpeg insists on trying to set V4L2_CID_MPEG_VIDEO_B_FRAMES to
0, and generates an error should it fail.
As our encoder doesn't support B frames, add a stub handler for
it to silence FFmpeg.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
V4L2_CID_MPEG_VIDEO_MPEG2_LEVEL was missed from
"vc04_services: bcm2835_codec: Ignore READ_ONLY ctrls in s_ctrl"
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
While waiting for random data, use sleeps that are proportional
to the amount of data expected. Prevent indefinite waits by
giving up if nothing is received for a second.
See: https://github.com/raspberrypi/linux/issues/5390
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
As of commit [1], introduced in 5.18, fbdev drivers that use
deferred IO and need mmap support must include an explicit fb_mmap
pointer to the fb_deferred_io_mmap.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
[1] 5905585103 ("fbdev: Put mmap for deferred I/O into drivers")
Setting V4L2_CID_WIDE_DYNAMIC_RANGE was causing the long exposure
shift count to be reset, which is incorrect if the user has already
changed the frame length to cause it to have a non-zero value.
Because it only updates control ranges and doesn't set any registers,
the control can also be applied when the sensor is not powered on.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
RGB is a mandatory format for all DVI and HDMI monitors so there's
no need to check for presence of the DRM_COLOR_FORMAT_RGB444 bit in
color_formats.
More importantly this checks breaks working around EDID issues with
eg video=HDMI-A-1:1024x768D or drm.edid_firmware=edid/1024x768.bin
as the RGB444 bit is only set when a valid EDID with digital bit set in
the input byte is present - which isn't the case when no EDID can be
read from the display device at all or with the in-built kernel EDIDs,
which mimic analog (VGA) displays without the digital bit set.
So drop the check, if we output video on the HDMI connector we can
assume that the display can accept 8bit RGB.
Signed-off-by: Matthias Reichl <hias@horus.com>
On Pi 4, raise the requested CMA size to 512MB by default, on the
understanding that the firmware will cap that to 256MB if it's a
32-bit kernel with less than 2GB of RAM.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Adding the cam1_reg label to the dummy camera regulator gets rid of an
error when all overlays are tried against all boards, and brings it
closer to what's happening in 6.2.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The HVS can change AXI request mode based on how full the COB
FIFOs are.
Until now the vc4 driver has been relying on the firmware to
have set these to sensible values.
With HVS channel 2 now being used for live video, change the
panic mode for all channels to be explicitly set by the driver,
and the same for all channels.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The RaspberryPi firmware clocks driver uses in several instances a
container_of to retrieve the struct raspberrypi_clk_data from a pointer
to struct clk_hw. Let's create a small function to avoid duplicating it
all over the place.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
With vc4-drv node not being under /soc on Pi4, we need to
adopt the correct DMA parameters from a suitable sub-component.
Add "brcm,bcm2711-hvs" to that list of components.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Busy spinning after halt is dumb
We've previously applied this patch to arch/arm
but it is currenltly missing in arch/arm64
Pi4 after "sudo halt" uses 520mA
Pi4 after "sudo shutdown now" uses 310mA
Make them both use the lower powered option
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
The change to using dma_max_mapping_size makes use of max_seg_size
and max_blk_count before the driver has set them. This makes the
new code a smaller change from the original.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
This commit updates the imx219 driver to adverise support for embedded
data streams. This can then be used by the bcm2835-unicam driver, which
has recently been updated to expose the embedded data stream to
userland.
The imx219 sensor subdevice overloads the media pad to differentiate
between image stream (pad 0) and embedded data stream (pad 1) when
performing the v4l2_subdev_pad_ops functions.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The HBLANK control was read-only, and always configured such
that the sensor HTS register was 3448. This limited the maximum
exposure time that could be achieved to around 1.26 secs.
Make HBLANK read/write so that the line time can be extended,
and thereby allow longer exposures (and slower frame rates).
Retain the overall HTS setting when changing modes rather than
resetting it to a default.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The datasheet for this sensor documents the minimum vblanking as being
32 lines. It does fix some problems with occasional black lines at the
bottom of images (tested on Raspberry Pi).
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Pi 400 doesn't have an ACT LED, only a green PWR LED, but a user may
wish to remap the ACT functionality to a GPIO on the 40-pin header.
Restore the ACT LED declaration, but leave it disabled in order to
prevent a GPIO being claimed until either the act_led_gpio dtparam
or the act-led overlay is used.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Historically, downstream Pi DTS files have named the LEDs led0 and (if
present) led1, while upstream have used the more meaningful "ACT" and
"PWR". As part of a closer alignment with upstream, make the LED names
match.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
This is currently running on defaults, so the --strict desired
for media drivers and similar won't be observed. That may be
possible to add later.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Having backported the mainline updates for the imx290.c driver,
update the overlays to reflect the slightly different compatible
strings used there.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Backport from https://patchwork.linuxtv.org/project/linux-media/list/?series=9918
The sensor supports H & V flips, so add the relevant hooks for
V4L2_CID_HFLIP and V4L2_CID_VFLIP to configure them.
Note that the Bayer order is maintained as the readout area
shifts by 1 pixel in the appropriate direction (note the
comment about the top margin being 8 pixels whilst the bottom
margin is 9). The V4L2_SEL_TGT_CROP region is therefore
adjusted appropriately.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Backport from https://patchwork.linuxtv.org/project/linux-media/list/?series=9918
Commit "97589ad61c73 media: i2c: imx290: Add support for 2 data lanes"
added support for running in two lane mode (instead of 4), but
without changing the link frequency that resulted in a max of 30fps.
Commit "98e0500eadb7 media: i2c: imx290: Add configurable link frequency
and pixel rate" then doubled the link frequency when in 2 lane mode,
but didn't undo the correction for running at only 30fps, just extending
horizontal blanking instead.
Remove the 30fps limit on 2 lane by correcting the register config
in accordance with the datasheet for 60fps operation over 2 lanes.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Backport from https://patchwork.linuxtv.org/project/linux-media/list/?series=9918
The datasheet lists the link frequency changes between
1080p and 720p modes. This is correct that the link frequency
changes as measured on an oscilloscope.
Link frequency is not necessarily the same as pixel rate.
The datasheet gives standard configurations for 1080p and 720p
modes at a number of frame rates.
Looking at the 1080p mode it gives:
HMAX = 0x898 = 2200
VMAX = 0x465 = 1125
2200 * 1125 * 60fps = 148.5MPix/s
Looking at the 720p mode it gives:
HMAX = 0xce4 = 3300
VMAX = 0x2ee = 750
3300 * 750 * 60fps = 148.5Mpix/s
This driver currently scales the pixel rate proportionally to the
link frequency, however the above shows that this is not the
correct thing to do, and currently all frame rate and exposure
calculations give incorrect results.
Correctly report the pixel rate as being 148.5MPix/s under any
mode.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Without a MODULE_DEVICE_TABLE declare for the of_device_ids, the
compatible strings won't be turned into module aliases.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
lirc-rpi was retired years ago, suggesting that this overlay is not
being used. Before deleting outright, remove the lirc-rpi element.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The ST7701 supports numerous different interface mechanisms for
MIPI DSI, RGB, or SPI. The driver was only implementing DSI input,
so add RGB parallel input with SPI configuration.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
In adding the MPEG2/MPEG4/H264 level and profile controls to
the decoder, they weren't declared as read-only, nor handlers
added to bcm2835_codec_s_ctrl. That resulted in an error message
"Invalid control" being logged every time v4l2_ctrl_handler_setup
was called from bcm2835_codec_create_component.
Define those controls as read only, and exit early from s_ctrl
on read only controls.
Fixes: "media: bcm2835-v4l2-codec: Add profile & level ctrls to decode"
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
In order to support discovery of what profile & levels are supported by
stateful decoders implement the profile and level controls where they
are defined by V4L2.
Signed-off-by: John Cox <jc@kynesim.co.uk>
The ISP cases do nothing. Remove the break that separates them from the
deinterlace case so they now do the same as deinterlace. This enables
simple width & height setting, but does not enable setting left and
top coordinates.
Signed-off-by: John Cox <jc@kynesim.co.uk>
With the RAW16 formats now having a defined CSI2 data type ID,
they can be added to the driver.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The MIPI CSI2 data type ID values are now defined in the
mipi-csi2.h header, so use those defines instead of hard
coding them in the driver.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Commit d3292daee3 ("dma-buf: Make locking consistent in dma_buf_detach()")
added checking that the same dmabuf for which dma_buf_attach
was called is passed into dma_buf_detach, which flagged up
that vcsm-cma was passing in the wrong dmabuf.
Correct this so that we don't get the WARN on every dma_buf
release.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Several of the media bus formats aren't merged upstream yet,
therefore the values change when upstream does introduce
new formats.
As vc4-kms-dpi-generic references the media bus formats explicitly
by number, update it to match.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Modify the kernel build workflow to create artifacts with the correct
names and structure, both as an example of what we expect and in case
anyone wants to use the output.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Add support for the MPU6050 and MPU9250 IMU sensors to the i2c-sensor
container overlay. At the same time, deprecate the standalone mpu6050
overlay, but keep it around for now.
(Also fix a few typos spotted while editing)
See: https://github.com/raspberrypi/linux/issues/5325
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
To avoid code with build warnings being introduced into the tree, force
CONFIG_WERROR=y in the build workflow.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
bcm2835_mmc_probe() ignores errors returned by mmc_of_parse() and in
particular ignores -EPROBE_DEFER, which may be returned if the power
sequencing driver configured in the devicetree is compiled as a module.
The user-visible result is that access to the SDIO device fails because
its power sequencing requirements have not been observed. Fix it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Since commit [1], the Kunit tests have failed with a linker error:
ERROR:root:`.exit.text' referenced in section `.uml.exitcall.exit' of \
arch/um/drivers/virtio_uml.o: defined in discarded section `.exit.text' \
of arch/um/drivers/virtio_uml.o
There's a suggestion that this is due to the use of an older binutils
package.
This patch, likely to soon be replaced by an official upstream change,
makes the Kunit builds work again with binutils 2.34.
See [2] for discussion of the problem, and the origin of this solution/
workaround.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
[1] 99cb0d917f ("arch: fix broken BuildID for arm64 and riscv")
[2] https://lore.kernel.org/lkml/20230110191404.132594-1-sj@kernel.org/T/
Enable long exposure modes by using the long exposure shift register setting
in the imx708 sensor.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
The mainline OV9282 driver also supports OV9281, and now
has feature parity with the downstream OV9281 driver, so
switch to using it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add support for the Measurement Specialities temperature and pressure
sensors to the i2c-sensor overlay. The supported devices are MS5637,
MS5803, MS5805, MS5837 and MS8607.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
CM4 uses BCM54210PE, which supports 2 additional LEDs, choosing LED3
for the amber LED because it shows activity by default (LED4 is not
connected). However, this makes it uncontrollable by the eth_led<n>
dtparams which target LEDs 1+2.
Solve the problem by making LEDs 3+4 mirror LEDs 1+2 (which is much
simpler than adding baseboard-specific overrides, but comes with a
risk of making one of the LEDs redundant).
See: https://github.com/raspberrypi/linux/issues/5289
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
New overlay to support the Sony IMX708 image sensor.
This includes a VCM for lens control.
Also adds support to the camera mux overlays.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The imx708 is a 12MP MIPI sensor with a 16:9 aspect ratio, here using
two CSI-2 lanes. It is a "quad Bayer" sensor with all 3 modes offering
10-bit output:
12MP: 4608x2592 up to 14.35fps (full FoV)
1080p: 2304x1296 up to 56.02fps (full FoV)
720p: 1536x864 up to 120.12fps (cropped)
This imx708 sensor driver is based heavily on the imx477 driver and
has been tested on the Raspberry Pi platform using libcamera.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add YAML devicetree binding for IMX708 CMOS image sensor.
Let's also add a MAINTAINERS entry for the binding and driver.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The power up/down sequence is already ramped. Extend this to
the first user movement as well, as this will generally avoid
the "tick" noises due to rapid movements and overshooting.
Subsequent movements are generally smaller and so don't cause
issues.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Uses the regulator notifier framework so that the current
focus position will be restored whenever any user of the
regulator powers it up. This means that should the VCM
and sensor share a common regulator then starting the sensor
will automatically restore the default position. If they
have independent regulators then it will behave be powered
up when the VCM subdev is opened.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The VCM driver will often be controlled via a regulator,
therefore add in the relevant DT hooks.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The DW9817 is effectively the same as DW9807 from a programming
interface, however it drives +/-100mA instead of 0-100mA. This means
that the power on ramp needs to take the lens from the midpoint, and
power off return it there. It also changes the default position for
the module.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The DW9817 is programmatically the same as DW9807, but
the output drive is a bi-directional -100 to +100mA
instead of 0-100mA.
Add the appropriate compativle string.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The brcm,function property must be set in the overlay fragment too -
otherwise the parametrization won't work. At least that's the case for
bcm2711-rpi-cm4.dts which starts with empty properties:
&gpio {
audio_pins: audio_pins {
brcm,pins = <>;
brcm,function = <>;
};
};
This was broken since a56df85d2f.
Signed-off-by: Krzysztof Kotlenga <k.kotlenga@sims.pl>
All the PWM drivers are now gated by CONFIG_PWM, so add that.
Similarly, NFSD_V2_ACL requires NFSD_V2.
Regenerating the defconfigs also acknowledges the loss of
CONFIG_CDROM_PKTCDVD and CONFIG_NFT_OBJREF.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
On some switches, having EEE enabled causes the link to become
unstable. With this patch, adding 'genet.eee=N' to the kernel command
line will cause EEE to be disabled on the link.
See: https://github.com/raspberrypi/linux/issues/4289
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
This is a copy of README with the tags added.
You can not delete the file README as then checkpatch complains
you aren't in a kernel tree.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Builds the bcmrpi, bcm2709, bcm2711, and bcm2835 32 bit kernels,
and defconfig and bcm2711 64bit kernels, saving the artifacts for
7 days.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Now that we have some KUnit coverage, let's add a github actions file to
run them on each push or pull request.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
As there isn't currently a defined mechanism for selecting an
external trigger mode on image sensors, copy the imx477
approach of using a module parameter to enable ext trig.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The integrated USB2.0 hub in the VL805 chipset has a bug where it
incorrectly determines the remaining available frame time before the
host next sends a SOF packet with an incremented frame_number.
See the USB2.0 specification sections 11.3 and 11.14.2.3.
The hub's non-periodic TT handler can transmit the IN/OUT handshake
token too late, so a following 64-byte DATA0/1 packet causes the ACK
handshake to collide with the propagated SOF. This causes port babble.
Avoid ringing doorbells for vulnerable endpoints during uFrame 7 if the
TR is Idle to stop one source of babble. An IN transfer for a Running TR
may happen at any time, so there's not much we can do about that.
Ideally a hub firmware update to properly implement frame timeouts is
needed, and to avoid spinning for up to 125us when submitting TDs to
Idle rings.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
xhci: constrain XHCI_VLI_HUB_TT_QUIRK to old firmware versions
VLI have a firmware update for the VL805 which resolves the incorrect
frame time calculation in the hub's TT. Limit applying the quirk to
known-bad firmwares.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Whilst the codecs are restricted to 1920x1080 / 1080x1920, the ISP
isn't, but the limits advertised via V4L2 was 1920x1920 for all
roles.
Increase the limit to 16k x 16k for the ISP.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Whilst the adv7180 driver support s_routing, nothing else
does, and there is a missing lump of framework code to
define the mapping from connectors on a board to the inputs
they represent on the ADV7180.
Add a nasty hack to take a module parameter that is passed in
to s_routing on any call to G_STD, or S_STD (or subdev
g_input_status call).
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
BCM54213PE is an Ethernet PHY that supports PTP hardware timestamping.
BCM54210PW ia another Ethernet PHY, but one without PTP support.
Unfortunately the two PHYs return the same ID when queried, so some
extra information is required to determine whether the PHY is PTP-
capable.
There are two Raspberry Pi products that use these PHYs - Pi 4B and
CM4 - and fortunately they use different PHY addresses, so use that as
a differentiator. Choose to treat a PHY with the same ID but another
address as a BCM54210PE, which seems more common.
See: https://github.com/raspberrypi/linux/issues/5104
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Configuring GCC to use task stack protector canaries means it will
insert calls to check functions in FIQ code. This is bad, as a) the
FIQ's stack is banked and b) the failure invokes __stack_chk_fail which
eventually tries to call printk(). Printing to the console inside the
FIQ is generally fatal.
Add CFLAGS to stop this happening in FIQ code.
Also catch one function where notrace wasn't specified.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
The pointer (struct usb_host_endpoint *)->hcpriv should contain a
reference to dwc_otg_qh_t if the driver has already seen a URB submitted
to this endpoint.
It then checks whether the qh exists and is already in a schedule in
order to decide whether to allocate periodic bandwidth or not. Passing a
pointer to an offset inside of struct usb_host_endpoint instead of just
the pointer means it dereferences bogus addresses.
Rationalise (delete) a variable while we're at it.
See https://github.com/raspberrypi/linux/issues/5189
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
The driver had a number of issues, checkpatch warnings/errors,
and other limitations, so fix these up to make it usable.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
As a result of [1], DRM_GEM_CMA_HELPER has been replaced by
DRM_GEM_CMA_HELPER.
[1] 4a83c26a1d ("drm/gem: rename GEM CMA helpers to GEM DMA helpers")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Add the ability to load the names of alternative firmwares from the
Device Tree node. This permits separate firmwares for 43436s and 43438
and allows downstream firmwares to coexist with upstream.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
It is reasonable to declare multiple nvmem blocks. Unless a unique 'id'
is passed in for each block there may be name clashes.
Avoid this by using the magic token NVMEM_DEVID_AUTO.
Fixes: 5a3fa75a4d ("nvmem: Add driver to expose reserved memory as nvmem")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
If a ring has a number of TDs enqueued past the dequeue pointer, and the
URBs corresponding to these TDs are dequeued, then num_trbs_free isn't
updated to show that these TDs have been converted to no-ops and
effectively "freed". This means that num_trbs_free creeps downwards
until the count is exhausted, which then triggers xhci_ring_expansion()
and effectively leaks memory by infinitely growing the transfer ring.
This is commonly encounted through the use of a usb-serial port where
the port is repeatedly opened, read, then closed.
Move the num_trbs_free crediting out of the Set TR Dequeue Pointer
handling and into xhci_invalidate_cancelled_tds().
There is a potential for overestimating the actual space on the ring if
the ring is nearly full and TDs are arbitrarily enqueued by a device
driver while it is dequeueing them, but dequeues are usually batched
during device close/shutdown or endpoint error recovery.
See https://github.com/raspberrypi/linux/issues/5088
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
The VL805 can cause data corruption if a SS Bulk OUT endpoint enters a
flow-control condition and there are TRBs in the transfer ring that are
not an integral size of wMaxPacket and the endpoint is behind one or more
hubs.
This is frequently the case encountered when FAT32 filesystems are
present on mass-storage devices with cluster sizes of 1 sector, and the
filesystem is being written to with an aggregate of small files.
The initial implementation of this quirk separated TRBs that didn't
adhere to this limitation into two - the first a multiple of wMaxPacket
and the second the 512-byte remainder - in an attempt to force TD
fragments to align with packet boundaries. This reduced the incidence
rate of data corruption but did not resolve it.
The fix as recommended by VIA is to disable bursts if this sequence of
TRBs can occur.
Limit turning off bursts to just USB mass-storage devices by searching
the device's configuration for an interface with a class type of
USB_CLASS_MASS_STORAGE.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
The Unicam hardware has been observed to cause a buffer overrun when using the
dummy buffer as a circular buffer. The conditions that cause the overrun are not
fully known, but it seems to occur when the memory bus is heavily loaded.
To avoid the overrun, program the hardware with a buffer size of 0 when using
the dummy buffer. This will cause overrun into the allocated dummy buffer, but
avoid out of bounds writes.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
There is no obligation for all source devices on a video-mux to
require the same bus configuration, so read the configuration
from the sink ports, and relay via get_mbus_config on the source
port.
If the sources support get_mbus_config, then call that first.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
If we get a simultaneous FS + FE interrupt for the same frame, it cannot be
marked as completed and returned to userland as the framebuffer will be refilled
by Unicam on the next sensor frame. Additionally, the timestamp will be set to 0
as the FS interrupt handling code will not have run yet.
To avoid these problems, the frame is considered dropped in the FE handler,
and will be returned to userland on the subsequent sensor frame.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
The clk-bcm2835 handling of the pixel clock does not function
correctly when the HDMI power domain is disabled.
The firmware supports it correctly, so add it to the
firmware clock driver.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The BCM54213PE identifier is a RPI-specific addition.
Populate the remainder of the driver functions, including the
required probe routine.
Add a version of bcm54xx_suspend, from upstream.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Also check for which HDMI devices are connected and only create
devices for those that are present.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
snd_bcm2835: disable HDMI audio when vc4 is used (#3640)
Things don't work too well when both the vc4 driver and the firmware
driver are trying to control the same audio output:
[ 763.569406] bcm2835_audio bcm2835_audio: vchi message timeout, msg=5
Hence, when the vc4 HDMI driver is used, let it control audio. This is done
by introducing a new device tree property to the audio node, and
extending the vc4-kms-v3d overlays to set it appropriately.
Signed-off-by: Hristo Venev <hristo@venev.name>
staging: bcm2835-audio: Add disable-headphones flag
Add a property to allow the headphone output to be disabled. Use an
integer property rather than a boolean so that an overlay can clear it.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
staging: bcm2835-audio: Find compatible firmware node
Commit "ARM: dts: Adopt the upstream snd_bcm2835 handling" removed the
audio section from the DT and the driver can no longer access the
referenced firmware node 'brcm,firmware'. Fix that by searching for a
compatible firmware node instead, similar to drivers/gpu/drm/vc4.
Fixes: b9e62329e096 ("ARM: dts: Adopt the upstream snd_bcm2835 handling")
Signed-off-by: Juerg Haefliger <juergh@proton.me>
staging: bcm2835-audio: Fix firmware node refcounting
Decrement firmware node refcounts on all exit paths in set_hdmi_enables().
Signed-off-by: Juerg Haefliger <juergh@proton.me>
staging: bcm2835-audio: Log errors in case of firmware query failures
The driver queries the firmware for the number of detected HDMI displays
and their IDs. Log error messages if queries fail.
Signed-off-by: Juerg Haefliger <juergh@proton.me>
staging: bcm2835-audio: Fix unused enable_hdmi module parameter
The commit "Add HDMI1 facility to the driver." made the enable_hdmi module
parameter unused. Fix that by making it a global switch for all available
HDMI audio outputs.
Fixes: 755f336608 ("Add HDMI1 facility to the driver.")
Signed-off-by: Juerg Haefliger <juergh@proton.me>
staging: bcm2835-audio: Fix unused enable_headphones module parameter
Since commit "staging: bcm2835-audio: Add disable-headphones flag" the
enabling/disabling of the headphones output is solely determined by the
presence of the DT property 'brcm,disable-headphones' and the
enable_headphones module parameter is unused. Fix that by making it a
global switch.
Fixes: ee90e47d88 ("staging: bcm2835-audio: Add disable-headphones flag")
Signed-off-by: Juerg Haefliger <juergh@proton.me>
This commit updates the arducam_64mp driver to adverise support for
embedded data streams.
The arducam_64mp sensor subdevice overloads the media pad to differentiate
between image stream (pad 0) and embedded data stream (pad 1) when
performing the v4l2_subdev_pad_ops functions.
Signed-off-by: Lee Jackson <info@arducam.com>
Add a driver for the Arducam 64MP camera sensor.
Whilst the sensor supports 2 or 4 CSI2 data lanes, this driver
currently only supports 2 lanes.
The following Bayer modes are currently available:
9152x6944 10-bit @ 2.7fps
4624x3472 10-bit (binned) @ 10fps
3840x2160 10-bit (cropped/binned) @ 20fps
2312x1736 10-bit (binned) @ 30fps
1920x1080 10-bit (cropped/binned) @ 60fps
1280x720 10-bit (cropped/binned) @ 120fps
Signed-off-by: Lee Jackson <info@arducam.com>
[ I would like to pursue fixing this more directly first before actually
merging this, but I thought I'd send this to the list now anyway as a
the "backup" plan. If I can't figure out how to make headway on the
main plan in the next few days, it'll be easy to just do this. ]
Stephen reported that a static key warning splat appears during early
boot on systems that credit randomness from device trees that contain an
"rng-seed" property, because because setup_machine_fdt() is called
before jump_label_init() during setup_arch():
static_key_enable_cpuslocked(): static key '0xffffffe51c6fcfc0' used before call to jump_label_init()
WARNING: CPU: 0 PID: 0 at kernel/jump_label.c:166 static_key_enable_cpuslocked+0xb0/0xb8
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 5.18.0+ #224 44b43e377bfc84bc99bb5ab885ff694984ee09ff
pstate: 600001c9 (nZCv dAIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : static_key_enable_cpuslocked+0xb0/0xb8
lr : static_key_enable_cpuslocked+0xb0/0xb8
sp : ffffffe51c393cf0
x29: ffffffe51c393cf0 x28: 000000008185054c x27: 00000000f1042f10
x26: 0000000000000000 x25: 00000000f10302b2 x24: 0000002513200000
x23: 0000002513200000 x22: ffffffe51c1c9000 x21: fffffffdfdc00000
x20: ffffffe51c2f0831 x19: ffffffe51c6fcfc0 x18: 00000000ffff1020
x17: 00000000e1e2ac90 x16: 00000000000000e0 x15: ffffffe51b710708
x14: 0000000000000066 x13: 0000000000000018 x12: 0000000000000000
x11: 0000000000000000 x10: 00000000ffffffff x9 : 0000000000000000
x8 : 0000000000000000 x7 : 61632065726f6665 x6 : 6220646573752027
x5 : ffffffe51c641d25 x4 : ffffffe51c13142c x3 : ffff0a00ffffff05
x2 : 40000000ffffe003 x1 : 00000000000001c0 x0 : 0000000000000065
Call trace:
static_key_enable_cpuslocked+0xb0/0xb8
static_key_enable+0x2c/0x40
crng_set_ready+0x24/0x30
execute_in_process_context+0x80/0x90
_credit_init_bits+0x100/0x154
add_bootloader_randomness+0x64/0x78
early_init_dt_scan_chosen+0x140/0x184
early_init_dt_scan_nodes+0x28/0x4c
early_init_dt_scan+0x40/0x44
setup_machine_fdt+0x7c/0x120
setup_arch+0x74/0x1d8
start_kernel+0x84/0x44c
__primary_switched+0xc0/0xc8
---[ end trace 0000000000000000 ]---
random: crng init done
Machine model: Google Lazor (rev1 - 2) with LTE
A trivial fix went in to address this on arm64, 73e2d827a5 ("arm64:
Initialize jump labels before setup_machine_fdt()"). But it appears that
fixing it on other platforms might not be so trivial. Instead, defer the
setting of the static branch until later in the boot process.
Fixes: f5bda35fba ("random: use static branch for crng_ready()")
Reported-by: Stephen Boyd <swboyd@chromium.org>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
There is a flags field in struct mmal_es_format, but the defines
for what the bits meant weren't included in the headers.
For V4L2_PIX_FMT_NV12_COL128 support we need them, so add them in.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
See https://github.com/raspberrypi/linux/issues/5019
If an SD card has degraded performance such that IO operations time out
then the MMC block layer will leak SG DMA mappings in the swiotlb during
recovery. It retries the same SG and this causes the leak, as it is
mapped twice - once in sdhci_pre_req() and again during single-block
reads in sdhci_prepare_data().
Resetting the card (including power-cycling if a regulator for vmmc is
present) ought to be enough to recover a stuck state, so for now don't
try single-block reads in the recovery path.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Mainline APIs have changed the way in which the bus flags and
number of active CSI2 data lanes is signalled, so fix the driver
up accordingly.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
It is quite common for the devm_thermal_zone_of_sensor_register
to need to defer, so avoid spamming the log by using
dev_err_probe instead of dev_err.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add a driver for the Arducam Pivariety series CSI2 camera sensor.
Signed-off-by: Lee Jackson <info@arducam.com>
SQUASH: Fix VIDEO_ARDUCAM_PIVARIETY Kconfig entry
The cherry-pick from rpi-5.17.y put it in the wrong section, and failed
to update it for 5.18.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Add YAML device tree binding for Arducam Pivariety CMOS image sensor, and
the relevant MAINTAINERS entries.
Signed-off-by: Lee Jackson <info@arducam.com>
The panel sends MIPI DCS commands during prepare and is expecting
the bus to remain in LP-11 state in-between.
Set the prepare_upstream_first flag so that the upstream DSI host
is prepared / pre_enabled first, and therefore the bus is in a
defined state.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
mipi_dsi_attach is allowed to fail, and currently the probe
code doesn't clean up (mainly drm_panel_remove) if this happens.
Add cleanup code on failure.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Allowing GPIO state to persist allows the use of gpioset to control
GPIO levels without having to use the --mode=wait feature.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
On some platforms the cma area can be half the entire system memory,
meaning that allocations start happening in the cma area immediately.
This leads to fragmentation and subsequent fatal cma_alloc failures.
We introduce an "alloc_in_cma_threshold" parameter which requires that
this many sixteenths of the free pages must be in cma before it will
try to use them. By default this is set to 12, but the previous
behaviour can be restored by setting it to 8 on startup.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
When all nodes have stopped streaming, ensure the firmware has released its
handle on the LS table dmabuf. This is done by passing a null handle in the
LS params.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
There's already a regulator module called ad5398 that exposes
this device through the regulator API. That is meaningless in
the terms that it uses and how it maps to V4L2, so a new driver
was added. However the module name collision wasn't noted, so
rename it now.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
v4l2_async_register_subdev doesn't bind in lens or flash drivers,
but v4l2_async_register_subdev_sensor does.
Switch to using v4l2_async_register_subdev_sensor.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Adds a driver for the Analog Devices AD5398 10 bit
I2C DAC which is commonly used for driving VCM lens
mechanisms.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add a binding for Analog Devices AD5398 10bit current
sinking DAC when used as a lens VCM driver.
FIXME: Convert to YAML
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
On stop_streaming() the vcsm buffer handle gets released by the buffer cleanup
code. This will subsequently cause and error if userland re-queues the same
buffer on the next start_streaming() call.
Remove this cleanup code and rely on the vb2_ops->buf_cleanup() call to do the
cleanups instead.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
ISP outputs actually support all colour spaces that are fundamentally
sRGB underneath, regardless of whether an RGB or YUV output format is
actually requested.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Fix incorrectly applying the quirk for bulk IN endpoints and remove the
commentary which is not completely accurate based on observed behaviour.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
"media: i2c: Remove .s_power() from ov7251" removed the call that
sent ov7251_global_init_setting to the sensor. Send it when starting
streaming.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The VL805 has a bug in its internal FIFO space accounting that results
in bulk OUT babble if a TRB in a large multi-element TD has a data
buffer size that is larger than and not a multiple of wMaxPacketSize for
the endpoint. If the downstream USB3.0 link is congested, or latency is
increased through an intermediate hub, then the VL805 enters a suspected
FIFO overflow condition and transmits repeated, garbled data to the
endpoint.
TDs with TRBs of exact multiples of wMaxPacketSize and smaller than
wMaxPacketSize appear to be handled correctly, so split buffers at a
1024-byte length boundary and put the remainder in a separate smaller
TRB.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
In the case of 2 frame starts being received with no frame end
between, the queued buffer held in next_frm was lost as the
pointer was overwritten with the dummy buffer.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The sck-idle-input property indicates that the spi-gpio driver should
return the SCK line to an input when the chip select signals are
inactive.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The Top DisplayOptoelectronics (TDO) T17B driver chip is used
in the TL040HDS20CT panel (found in the Pimoroni HyperPixel4
Square display) and potentially other displays.
The driver chip supports SPI for configuration and DPI
video data.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The Ilitek ILI9806E driver is used in the Pimoroni HyperPixel4
and potentially other displays. Whilst it can support multiple
interfaces, this driver only accounts for SPI configuration and
DPI video data.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Panel orientation is now handled by the drm_panel and
panel_bridge frameworks, so remove the custom handling.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The Geekworm MZP280 panel is a 480x640 (portrait) panel with a
capacitive touch interface and a 40 pin header meant to interface
directly with the Raspberry Pi. The screen is 2.8 inches diagonally,
and there appear to be at least 4 distinct versions all with the same
panel timings.
Timings were derived from drivers posted on the github located here:
https://github.com/tianyoujian/MZDPI/tree/master/vga
Additional details about this panel family can be found here:
https://wiki.geekworm.com/2.8_inch_Touch_Screen_for_Pi_zero
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Add support for MEDIA_BUS_FMT_RGB565_1X24_CPADHI. This format is used
by the Geekworm MZP280 panel which interfaces with the Raspberry Pi.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
The default clock-stretch timeout is 35 mS, which works well for
SMBus, but there are some I2C devices which can stretch the clock even
longer. Rather than trying to prescribe a safe default for everyone,
allow the timeout to be configured.
Signed-off-by: Alex Crawford <raspberrypi/linux@code.acrawford.com>
Clang warns:
drivers/media/platform/bcm2835/bcm2835-unicam.c:3109:6: warning: variable 'ret' is used uninitialized whenever 'if' condition is true [-Wsometimes-uninitialized]
if (!source_pads) {
^~~~~~~~~~~~
drivers/media/platform/bcm2835/bcm2835-unicam.c:3152:9: note: uninitialized use occurs here
return ret;
^~~
drivers/media/platform/bcm2835/bcm2835-unicam.c:3109:2: note: remove the 'if' if its condition is always false
if (!source_pads) {
^~~~~~~~~~~~~~~~~~~
drivers/media/platform/bcm2835/bcm2835-unicam.c:3091:9: note: initialize the variable 'ret' to silence this warning
int ret;
^
= 0
1 warning generated.
When the if condition is true, ret will be used uninitialized, which
could result in undesirable behavior. Set ret to -ENODEV on the error
path, which is a standard error code for the ->complete() callback.
Fixes: d056e86eb3 ("media/bcm2835-unicam: Parse pad numbers correctly")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
On a Pi3 B/B+ platform the imx219 sensor frequently generates a single corrupt
frame when the sensor first starts. This can either be a missing line, or
invalid samples within the line. This only occurrs using the Unicam kernel
driver.
Disabling trigger mode elimiates this corruption. Since trigger mode is a
legacy feature copied from the firmware driver and not expected to be needed,
remove it. Tested on the Raspberry Pi cameras and shows no ill effects.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
The firmware can only use I2C0 if the kernel isn't, therefore
with libcamera and DRM using it the PoE HAT fan control needs
to move to the kernel.
Add the option for the driver to be created by the PoE HAT core
MFD driver, and use the I2C regmap that provides to control fan
functions.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
As documented the _AVG parameters are meant to be hardware
averaged, but the implementation for the PoE+ HAT was done in
software in the firmware.
Drop the property.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The firmware can only use I2C0 if the kernel isn't, therefore
with libcamera and DRM using it the PoE HAT fan control needs
to move to the kernel.
Add the option for the driver to be created by the PoE HAT core
MFD driver, and use the I2C regmap that provides to control fan
functions.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The Raspbery Pi PoE+ HAT exposes a fan controller and power
supply status reporting via a single I2C address.
Create an MFD device that allows loading of the relevant
sub-drivers, with a shared I2C regmap.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Use GitHubs issue form for bug reports.
- modern look
- user don't need to mess with given markdown parts while filling the issue template
Setup config.yml for general questions and problems with the Raspbian distribution packages.
https://github.com/raspberrypi/linux/issues/4440
Upstream has added additional device specific controls, so the
V4L2_CID_USER_BASE + 0x10e0 value that had been defined for use with
the ISP has been taken by something else (and +0x10f0 has been used as
well)
Duplicate the use on V4L2_CID_USER_BASE + 0x10e0 so that userspace
(libcamera) doesn't need to change. Once the driver is upstream, then
we'll update libcamera to adopt the new value as it then won't change.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
bcm2835_isp_remove is called on an initialisation failure, but at that
point the drvdata hasn't been set. This causes a crash when e.g. using
the cutdown firmware (gpu_mem=16).
Move platform_set_drvdata before the instance probing loop to avoid the
problem.
See: https://github.com/raspberrypi/linux/issues/4774
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Not all implementations wire up the enable GPIO and may just tie
it to a supply rail.
Make it optional.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The driver supported using GPIOs to control the shutdown line,
but no regulator control.
Add regulator hooks.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The VL805 fetches up to 4 transfer TRBs at a time. TRB reads don't cross
a 64B boundary, and if a TRB is fetched and is not on a 64B boundary,
the read is sized up to the next 64B boundary.
However the VL805 implements a readahead prefetch for TRBs on a transfer
ring. This fetches the next 64B after any TRB read has happened. Near
the end of a ring segment, the prefetcher can read the first 64B of the
next page in physical memory and this is where the behaviour causes a
bug.
The controller does not tag reads with which endpoint they are for, so
if the start of the next page is a ring segment used by a victim
endpoint, and the victim endpoint is about to fetch TRBs from the start
of the segment, the victim endpoint will read from the prefetched data
and not perform a read to main memory. If the data is stale, the ring
cycle state bit may not be correct and the endpoint will silently halt.
Adjust trbs_per_seg for transfer rings allocated for this controller.
See https://github.com/raspberrypi/linux/issues/4685
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
In anticipation of adjusting the number of utilised TRBs in a ring
segment, add trbs_per_seg to struct xhci_ring and use this instead
of a compile-time define.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Don't calculate space based on the number of TRBs in the current segment,
as it's OK to wrap to the start (and flip the cycle state bit).
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
The VL805 controller can't cope with the TR Dequeue Pointer for an endpoint
being set to a Link TRB. The hardware-maintained endpoint context ends up
stuck at the address of the Link TRB, leading to erroneous ring expansion
events whenever the enqueue pointer wraps to the dequeue position.
If the search for the end of the current TD and ring cycle state lands on
a Link TRB, move to the next segment.
See: https://github.com/raspberrypi/linux/issues/3919
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
The "panel-dpi" compatible string configures panel from device tree,
but it doesn't provide any way of configuring the bus format (colour
representation), nor does it populate it.
Add a DT parameter "bus-format" that allows the MEDIA_BUS_FMT_xxx value
to be specified from device tree.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
panel-dpi doesn't know the bit depth, so in the same way that
DPI is guessed for the connector type, guess that it'll be 8bpc.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Register 0x02 in the FT5x06 is TD_STATUS containing the number
of valid touch points being reported.
Iterate over that number of points rather than all that are
supported on the device.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The I2C to the Atmel is very fussy, and locks up easily on
Pi0-3 particularly on reads.
The LCD power status is controlled solely by this driver, so
rather than reading it back from the Atmel, use the cached
status last set.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
If a dummy buffer is still active on a frame start, it indicates that this frame
will be dropped. The explicit logging helps users identify performance issues.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
The ft5x06 is unreliable in sending touch up events, so some
touch IDs can become stuck in the detected state.
Ensure that IDs that are unreported by the controller are
released.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
As happens occasionally, an upstream change has once again prevented
spidev from being loaded via Device Tree. We now need "spidev" to be
included in the new spi_device_id list, otherwise although the
spidev driver gets loaded no /dev/spidev*.* entries will appear.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Add a second (identical) set of device nodes to allow concurrent use of the ISP
hardware by another user. This change effectively creates a second state
structure (struct bcm2835_isp_dev) to maintain independent state for the second
user. Node and media entity names are appened with the instance index
appropriately.
Further users can be added by changing the BCM2835_ISP_NUM_INSTANCES define.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Add these missing V4L2 controls. Tested binned and full resolution
modes in all four orientations using Raspberry Pi running libcamera.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
An unwanted side effect of enabling the BRCMDBG config setting is
redefining brcmf_info to be brcmf_err. This can be alarming to users
and makes it harder to spot real errors, so don't do it.
See: https://github.com/raspberrypi/linux/issues/4663
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Adds Media Controller API support for more complex pipelines.
libcamera is about to switch to using this mechanism for configuring
sensors.
This can be enabled by either a module parameter, or device tree.
Various functions have been moved to group video-centric and
mc-centric functions together.
Based on a similar conversion done to ti-vpe.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: bcm2835-unicam: Fixup for 5.18 and new get_mbus_config struct
The number of active CSI2 data lanes has moved within the struct
v4l2_mbus_config used by the get_mbus_config API call.
Update the driver to match the changes in mainline.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The driver was making big assumptions about the source device
using pad 0 and 1, which doesn't follow for more complex
devices where Unicam's source device may be a sink device for
something else.
Read the pad numbers through media controller, and reference
them appropriately.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
RAW color spaces are more usually reported as having full range
quantization.
Tested using libcamera.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
For cases where spare PWM outputs are available, but are desired
to be addressed a standard outputs instead.
Wraps a PWM channel as a new GPIO chip with the one output.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Should we go through the timeout failure case with port_disable
not returning all buffers for whatever reason, the
buffers_with_vpu counter gets left at a non-zero value, which
will cause reference counting issues should the instance be
reused.
Reset the count when the port is enabled again, but before
any buffers have been sent to the VPU.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
As we're wanting to wrap the image_fx component for deinterlacing,
add the deinterlace algorithm values to enum mmal_parameter_imagefx
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Adds enum mmal_interlace_type and struct
mmal_parameter_video_interlace_type to allow for querying the
interlacing mode on decoders.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
If no interrupt is defined then a timer and workqueue are used
to poll the controller.
On remove these were not being cleaned up correctly.
Fixes: ca61fdaba7 "Input: edt-ft5x06: Poll the device if no interrupt is
configured."
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The Raspberry Pi 7" 800x480 panel uses a Toshiba TC358762 DSI
to DPI bridge chip, so there is a requirement for the timings
to be specified for the end panel. Add such a definition.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
rpi_touchscreen_i2c_read returns any errors from i2c_transfer,
or the 8 bit received value.
Check for error values before trying to process the data as
valid.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
During a bulk transfer we request a DMA allocation to hold the
scatter-gather list. Most of the time, this allocation is small
(<< PAGE_SIZE), however it can be requested at a high enough frequency
to cause fragmentation and/or stress the CMA allocator (think time
spent in compaction here, or during allocations elsewhere).
Implement a pool to serve up small DMA allocations, falling back
to a coherent allocation if the request is greater than
VCHIQ_DMA_POOL_SIZE.
Signed-off-by: Oliver Gjoneski <ogjoneski@gmail.com>
Although it is no longer necessary for vchiq's children to have a
different DMA configuration to the parent, they do still need to
explicitly to have their DMA configuration set - to be that of the
parent.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Conditional on a new compatible string, change the pagelist encoding
such that the top 24 bits are the pfn, leaving 8 bits for run length
(-1), giving a 36-bit address range.
Manage the split between addresses for the VPU and addresses for the
40-bit DMA controller with a dedicated DMA device pointer that on non-
BCM2711 platforms is the same as the main VCHIQ device. This allows
the VCHIQ node to stay in the usual place in the DT.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
See https://github.com/raspberrypi/linux/issues/3981
An unknown unsafe memory access can result in the ep_state variable
in xhci_virt_ep being trampled with a stuck SET_DEQ_PENDING state
despite successful completion of a Set TR Deq Pointer command.
All URB enqueue/dequeue calls for the endpoint will fail in this state
so no transfers are possible until the device is reconnected.
As a workaround, clear the flag if we see it set and issue a new Set
TR Deq command anyway - this should be harmless, as a prior Set TR Deq
command will only have been issued in the Stopped state, and if the
endpoint is Running then the controller is required to ignore it and
respond with a Context State Error event TRB.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Add call to v4l2_ctrl_new_fwnode_properties to read and
create the fwnode based controls.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The vidioc_enum_input() v4l2 ioctl is capable of returning
sensor/input status as well. This is used in current
GStreamer HEAD for signal detection [1].
bcm2835-unicam does handle this syscall, but it didn't ask
the subdevice driver about the input status. The input then
appeared as always present.
This commit adds the necessary query. There is a precedent for
this - the R-Car VIN V4L2 driver does a similar call [2].
[1]: ce0be27caf/sys/v4l2/gstv4l2src.c (L553)
[2]: 7fb9d006d3/drivers/media/platform/rcar-vin/rcar-v4l2.c (L548)
Signed-off-by: Jakub Vaněk <linuxtardis@gmail.com>
The bcm2835 ISP requires the base address of all input/output planes to have 32
byte alignment. Using a Y stride of 32 bytes would not guarantee that the V
plane would fulfil this, e.g. a height of 650 lines would mean the V plane
buffer is not 32 byte aligned for YUV420 formats.
Having a Y stride of 64 bytes would ensure both U and V planes have a 32 byte
alignment, as the luma height will always be an even number of lines.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Fixes the following v4l2-compliance failure:
fail: v4l2-test-controls.cpp(871): subscribe event for control 'User Controls' failed test
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Trial and error reveals that the minimum vblank value appears to be 24
(the OV5647 data sheet does not give any clues). This fixes streaming
lock-ups in full resolution mode.
Fixes: 9b5a5ebedc ("media: i2c: ov5647: Add support for V4L2_CID_VBLANK")
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
The top offset in the pixel array is actually 6 (see page 3-1 of the
OV5647 data sheet).
Fixes: f2f7ad5ce5 ("media: i2c: ov5647: Selection compliance fixes")
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Keeping a copy of the old poweroff handler allows it to be restored
should this module be unloaded, but also provides a fallback if the
power hasn't been removed when the timeout elapses.
See: https://github.com/raspberrypi/rpi-eeprom/issues/330
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The result of dividing a u32 by a size_t is an unsigned int on arm32
and a long unsigned int on arm64. Use "%zu" (the size_t format) to
remove the build warning for 64-bit builds.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Whilst the hardware can't achieve the limits of level 4.2 under
all situations, it can exceed level 4.0.
Allow selection of levels 4.1 and 4.2.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
There is no reason why the control GPIOs for the panel can not
be connected to I2C or similar GPIO interfaces that may need to
sleep, therefore switch from gpiod_set_value to
gpiod_set_value_cansleep calls to configure them.
Without that you get complaints from gpiolib every time the state
is changed.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The Adafruit Mini-PiTFT13 display needs offsets applying when rotated,
so use the "variant" mechanism to select a custom set_addr_win method
using a dedicated compatible string of "fbtft,minipitft13".
See: https://github.com/raspberrypi/firmware/issues/1524
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
DMABUFs are all handled by videobuf2, so there is no reason not
to enable support for them.
Note that this driver is still using the vmalloc allocator, so
the buffers it allocates will not be compatible with the codec
or ISP driver that require contiguous buffers. However this
driver should be able to import the buffers allocated by them.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Parse device properties and register controls for them using the V4L2
fwnode properties helpers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Previously they were returning positive non-zero codes for success,
which were getting passed up the call stack. Since release 4.19,
do_dentry_open (fs/open.c) has been catching these and flagging an
error. (So this driver has been broken since that date.)
Fixes: 3c2472a [media] media: i2c: Add support for OV5647 sensor
Signed-off-by: David Plowman <david.plowman@raspberrypi.org>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Change-Id: I7b77250bbc56d2f861450cf77271ad15f9b88ab1
Signed-off-by: Zefa Chen <zefa.chen@rock-chips.com>
media: i2c: ov9281: fix mclk issue when probe multiple camera.
Takes the ov9281 part only from the Rockchip's patch.
Change-Id: I30e833baf2c1bb07d6d87ddb3b00759ab45a90e4
Signed-off-by: Zefa Chen <zefa.chen@rock-chips.com>
media: i2c: ov9281: add enum_frame_interval function for iq tool 2.2 and hal3
Adds the ov9281 parts of the Rockchip patch adding enum_frame_interval to
a large number of drivers.
Change-Id: I03344cd6cf278dd7c18fce8e97479089ef185a5c
Signed-off-by: Zefa Chen <zefa.chen@rock-chips.com>
media: i2c: ov9281: Fixup for recent kernel releases, and remove custom code
The Rockchip driver was based on a 4.4 kernel, and had several custom
Rockchip parts.
Update to 5.4 kernel APIs, with the relevant controls required by
libcamera, and remove custom Rockchip parts.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: i2c: ov9281: Read chip ID via 2 reads
Vision Components have made an OV9281 module which blocks reading
back the majority of registers to comply with NDAs, and in doing
so doesn't allow auto-increment register reading as used when
reading the chip ID.
Use two reads and manually combine the results.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: i2c: ov9281: Add support for 8 bit readout
The sensor supports 8 bit mode as well as 10bit, so add the
relevant code to allow selection of this.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: ov9281: Add 1280x720 and 640x480 modes
Breaks out common register set and adds the different registers
for 1280x720 (cropped) and 640x480 (skipped) modes
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Fixed picture line bug in all ov9281 modes
Signed-off-by: Mathias Anhalt <mathiasanhalt@web.de>
Added hflip and vflip controls to ov9281
Signed-off-by: Mathias Anhalt <mathiasanhalt@web.de>
media: i2c: ov9281: Remove override of subdev name
From the original Rockchip driver, the subdev was renamed
from the default to being "mov9281 <dev_name>" whereas the
default would have been "ov9281 <dev_name>".
Remove the override to drop back to the default rather than
a vendor custom string.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: v4l2-subdev: add subdev-wide state struct
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
media: i2c: ov9281: Add fwnode properties controls
Add call to v4l2_ctrl_new_fwnode_properties to read and
create the fwnode based controls.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: i2c: ov9281: Sensor should report RAW color space
Tested on Raspberry Pi running libcamera.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Partial revert "media: i2c: add ov9281 driver."
This partially reverts commit 84e98e3a4f.
The commit had merged some changes to other drivers with adding the ov9281
driver. Only the ov9281 parts have been reverted.
In order to get the intended behaviour of the stateful video
decoder API where only the OUTPUT queue needs to be enabled and fed
buffers in order to get the SOURCE_CHANGED event that configures the
CAPTURE queue, we want the device to run should either queue be
streaming.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The kernel modules aes-neon-blk and aes-neon-bs perform poorly, at least on
Cortex-A72 without crypto extensions. In fact, aes-arm64 outperforms them
on benchmarks, despite it being a simpler implementation (only accelerating
the single-block AES cipher).
For modes of operation where multiple cipher blocks can be processed in
parallel, aes-neon-bs outperforms aes-neon-blk by around 60-70% and aes-arm64
is another 10-20% faster still. But the difference is even more marked with
modes of operation with dependencies between neighbouring blocks, such as
CBC encryption, which defeat parallelism: in these cases, aes-arm64 is
typically around 250% faster than either aes-neon-blk or aes-neon-bs.
The key trade-off with aes-arm64 is that the look-up tables are situated in
RAM. This leaves them potentially open to cache timing attacks. The two other
modules, by contrast, load the look-up tables into NEON registers and so are
able to perform in constant time.
This patch aims to load aes-arm64 more often.
If none of the currently-loaded crypto modules implement a given algorithm,
a new one is typically selected for loading using a platform-neutral alias
describing the required algorithm. To enable users to still
load aes-neon-blk or aes-neon-bs if they really want them, while still
ensuring that aes-arm64 is usually selected, remove the aliases from
aes-neonbs-glue.c and aes-glue.c and apply them to aes-cipher-glue.c, but
still build the two NEON modules.
Since aes-glue.c can also be used to build aes-ce-blk, leave them enabled
if USE_V8_CRYPTO_EXTENSIONS is defined, to ensure they are selected if we
in future use a CPU which has the crypto extensions enabled.
Note that the algorithm priority specifiers are unchanged, so if
aes-neon-bs is loaded at the same time as aes-arm64, the former will be
used in preference. However, aes-neon-blk and aes-arm64 have tied priority,
so whichever module was loaded first will be used (assuming aes-neon-bs is
not loaded).
Signed-off-by: Ben Avison <bavison@riscosopen.org>
If multiple sets of interrupts occur simultaneously, it may be unsafe
to swap buffers, as the hardware may already be re-using the current
buffers. In such cases, avoid swapping buffers, and wait for the next
opportunity at the Frame End interrupt to signal completion.
Additionally, check the packet compare status when watching for frame
end for buffers swaps, as this could also signify a frame end event.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Each supported format now includes a mask showing the allowed colour
spaces, as well as a default colour space for when one was not
specified.
Additionally we translate the colour space to mmal format and pass it
over to the VideoCore.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Much effort has been put into finding ways to avoid warnings from dtc
about overlays, usually to do with the presence of #address-cells and
size-cells, but not exclusively so. Since the issues being warned about
are harmless, suppress the warnings to declutter the build output and
to avoid alarming users.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
A relatively recent commit ([1]) contained optimisation for the PIO
SPI FIFO-filling functions. The commit message includes the phrase
"[t]he blind and counted loops are always called with nonzero count".
This is technically true, but it is still possible for count to become
zero before the loop is entered - if tfr->len is zero. Moving the loop
exit condition to the end of the loop saves a few cycles, but results
in a near-infinite loop should the revised count be zero on entry.
Strangely, zero-lengthed transfers aren't filtered by the SPI framework
and, even more strangely, the Python3 spidev library is triggering them
for no obvious reason.
Avoid the problem completely by bailing out of the main transfer
function early if trf->len is zero, although there may be a case for
moving the mitigation into the framework.
See: https://github.com/raspberrypi/linux/issues/4100
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
[1] 26751de25d ("spi: bcm2835: Micro-optimise FIFO loops")
Add colour denoise control to the bcm2835 driver through a new v4l2
control: V4L2_CID_USER_BCM2835_ISP_CDN.
Add the accompanying MMAL configuration structure definitions as well.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Use (reserved) bits 24 and 25 of the dreq value
(the second cell of the DT DMA descriptor) to request
that wide source reads or wide dest writes are required
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
When logging that the firmware has provided more supported formats
than we had allocated storage for, log the number allocated and
returned.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Now that the firmware supports the unpacked (16bpp) variants
of the MIPI raw formats, add the mappings.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Support has been added for the unpacked (16bpp) versions of
the MIPI raw 10, 12, and 14 formats, so add the 4CCs for them.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
error logs:
drivers/staging/vc04_services/vc-sm-cma/Kconfig:1:error: recursive dependency detected!
drivers/staging/vc04_services/vc-sm-cma/Kconfig:1: symbol BCM_VC_SM_CMA is selected by BCM2835_VCHIQ_MMAL
drivers/staging/vc04_services/vchiq-mmal/Kconfig:1: symbol BCM2835_VCHIQ_MMAL depends on BCM2835_VCHIQ
drivers/staging/vc04_services/Kconfig:14: symbol BCM2835_VCHIQ is selected by BCM_VC_SM_CMA
For a resolution refer to Documentation/kbuild/kconfig-language.rst
subsection "Kconfig recursive dependency limitations"
Tested-by: make ARCH=arm64 bcm2711_defconfig
Test platform: fedora 33
Branch: rpi-5.10.y
lan78xx_link_reset explicitly clears the MAC's view of the PHY's IRQ
status. In doing so it potentially leaves the PHY with a pending
interrupt that will never be acknowledged, at which point no further
interrupts will be generated.
Avoid the problem by acknowledging any pending PHY interrupt after
clearing the MAC's status bit.
See: https://github.com/raspberrypi/linux/issues/2937
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Although the BRCMSTB PCIe interface doesn't technically support the
MSI-X spec, in practise it seems to work provided no more than 32
MSI-Xs are required. Add the required flag to the driver to allow
experimentation with devices that demand MSI-X support.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Commit 65e08c4650 failed to clear the
clock state when the device stopped streaming. Fix this, as it might
again cause the same problems when doing an unprepare.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
clk_disable_unprepare() is called unconditionally in stop_streaming().
This is incorrect in the cases where start_streaming() fails, and
unprepares all clocks as part of the failure cleanup. To avoid this,
ensure that clk_disable_unprepare() is only called in stop_streaming()
if the clocks are in a prepared state.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
On a failure in start_streaming(), the error code would not propagate to
the calling function on all conditions. This would cause the userland
caller to not know of the failure.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
DSI1 on BCM2711 doesn't require the DMA workaround that is used
on BCM2835/6/7, therefore it needs a new compatible string.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
In switching to the hardware I2C controller there is an issue
where we seem to not get back the correct state from the Pi
touchscreen.
Insert a delay before polling to avoid this condition.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
We now have the hardware I2C controller pinmuxed to the drive the
display I2C, but this controller does not support clock stretching.
The Atmel micro-controller in the panel requires clock stretching
to allow it to prepare any data to be read.
Split the rpi_touchscreen_i2c_read into two independent transactions with
a delay between them for the Atmel to prepare the data.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Not all systems have the interrupt line wired up, so switch to
polling the touchscreen off a timer if no interrupt line is
configured.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
[1] replaced a single reset function with a pointer to one of two
implementations, but also removed the call asserting the reset
at the start of brcm_pcie_setup. Doing so breaks Raspberry Pis with
VL805 XHCI controllers lacking dedicated SPI EEPROMs, which have been
used for USB booting but then need to be reset so that the kernel
can reconfigure them. The lack of a reset causes the firmware's loading
of the EEPROM image to RAM to fail, breaking USB for the kernel.
See: https://www.raspberrypi.org/forums/viewtopic.php?p=1758157#p1758157
Fixes: 04356ac307 ("PCI: brcmstb: Add bcm7278 PERST# support")
[1] 04356ac307 ("PCI: brcmstb: Add bcm7278 PERST# support")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The last nibble is a revision ID, and the 54213pe is a later rev
than the 54210e. Running the 54210e setup code on a 54213pe results
in a broken RGMII interface.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Define a new mailbox (SET_REBOOT_FLAGS) which may be used to
pass optional flags to the Raspberry Pi firmware that changes
the behaviour of the bootloader and firmware during a reboot.
Currently this just defines the 'tryboot' flag which causes
the firmware to load tryboot.txt instead config.txt. This
alternate configuration file can be used to specify the
path of an alternate firmware and kernels allowing a fallback
mechanism to be implemented for OS upgrades.
The gpio-fsm driver implements simple state machines that allow GPIOs
to be controlled in response to inputs from other GPIOs - real and
soft/virtual - and time delays. It can:
+ create dummy GPIOs for drivers that demand them,
+ drive multiple GPIOs from a single input, with optional delays,
+ add a debounce circuit to an input,
+ drive pattern sequences onto LEDs
etc.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
gpio-fsm: Fix a build warning
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
gpio-fsm: Rename 'num-soft-gpios' to avoid warning
As of 5.10, the Device Tree parser warns about properties that look
like references to "suppliers" of various services. "num-soft-gpios"
resembles a declaration of a GPIO called "num-soft", causing the value
to be interpreted as a phandle, the owner of which is checked for a
"#gpio-cells" property.
To avoid this warning, rename the gpio-fsm property to "num-swgpios".
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
gpio-fsm: Show state info in /sys/class/gpio-fsm
Add gpio-fsm sysfs entries under /sys/class/gpio-fsm. For each state
machine show the current state, which state (if any) will be entered
after a delay, and the current value of that delay.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
gpio-fsm: Fix shutdown timeout handling
The driver is intended to jump directly to a shutdown state in the
event of a timeout during shutdown, but the sense of the test was
inverted.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
gpio-fsm: Clamp the delay time to zero
The sysfs delay_ms value is calculated live, and it is possible for
the time left to appear to be negative briefly if the timer handling
hasn't completed. Ensure the displayed value never goes below zero,
for the sake of appearances.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Driver for the BCM2835 ISP hardware block. This driver uses the MMAL
component to program the ISP hardware through the VC firmware.
The ISP component can produce two video stream outputs, and Bayer
image statistics. This can't be encompassed in a simple V4L2
M2M device, so create a new device that registers 4 video nodes.
This patch squashes all the development patches from the earlier
rpi-5.4.y branch into one
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
This file defines the userland interface to the bcm2835-isp driver
that will follow in a separate commit.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
If CONFIG_DMA_BCM2708 isn't enabled there's no need to mask out
one of the already scarce DMA channels.
Signed-off-by: Matthias Reichl <hias@horus.com>
This adds a V4L2 memory to memory device that wraps the MMAL
video decode and video_encode components for H264 and MJPEG encode
and decode, MPEG4, H263, and VP8 decode (and MPEG2 decode
if the appropriate licence has been purchased).
This patch squashes all the work done in developing the driver
on the Raspberry Pi rpi-5.4.y kernel branch.
Thanks to Kieran Bingham, Aman Gupta, Chen-Yu Tsai, and
Marek Behún for their contributions. Please refer to the
rpi-5.4.y branch for the full history.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Ensure OUTPUT timestamps are always forwarded
The firmware by default tries to ensure that decoded frame
timestamps always increment. This is counter to the V4L2 API
which wants exactly the OUTPUT queue timestamps passed to the
CAPTURE queue buffers.
Disable the firmware option.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/vc04_services/codec: Add support for CID MPEG_HEADER_MODE
Control V4L2_CID_MPEG_VIDEO_HEADER_MODE controls whether the encoder
is meant to emit the header bytes as a separate packet or with the
first encoded frame.
Add support for it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/vc04_services/codec: Clear last buf dequeued flag on START
It appears that the V4L2 M2M framework requires the driver to manually
call vb2_clear_last_buffer_dequeued on the CAPTURE queue during a
V4L2_DEC_CMD_START.
Add such a call.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/vc04-services/codec: Fix logical precedence issue
Two issues identified with operator precedence in logical
expressions. Fix them.
https://github.com/raspberrypi/linux/issues/4040
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
vc04_services: bcm2835-codec: Switch to s32fract
staging/bcm2835-codec: Add the unpacked (16bpp) raw formats
Now that the firmware supports the unpacked (16bpp) variants
of the MIPI raw formats, add the mappings.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Log the number of excess supported formats
When logging that the firmware has provided more supported formats
than we had allocated storage for, log the number allocated and
returned.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Add support for pixel aspect ratio
If the format is detected by the driver and a V4L2_EVENT_SOURCE_CHANGE
event is generated, then pass on the pixel aspect ratio as well.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Implement additional g_selection calls for decode
v4l_cropcap calls our vidioc_g_pixelaspect function to get the pixel
aspect ratio, but also calls g_selection for V4L2_SEL_TGT_CROP_BOUNDS
and V4L2_SEL_TGT_CROP_DEFAULT. Whilst it allows for vidioc_g_pixelaspect
not to be implemented, it doesn't allow for either of the other two.
Add in support for the additional selection targets.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Add VC-1 support.
Providing the relevant licence has been purchased, then Pi0-3
can decode VC-1.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Fix support for levels 4.1 and 4.2
The driver said it supported H264 levels 4.1 and 4.2, but
was missing the V4L2 to MMAL mappings.
Add in those mappings.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Set the colourspace appropriately for RGB formats
Video decode supports YUV and RGB formats. YUV needs to report SMPTE170M
or REC709 appropriately, whilst RGB should report SRGB.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Pass corrupt frame flag.
MMAL has the flag MMAL_BUFFER_HEADER_FLAG_CORRUPTED but that
wasn't being passed through, so add it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Do not update crop from S_FMT after res change
During decode, setting the CAPTURE queue format was setting the crop
rectangle to the requested height before aligning up the format to
cater for simple clients that weren't expecting to deal with cropping
and the SELECTION API.
This caused problems on some resolution change events if the client
didn't also then use the selection API.
Disable the crop update after a resolution change.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
bcm2835: Allow compressed frames to set sizeimage (#4386)
Allow the user to set sizeimage in TRY_FMT and S_FMT if the format
flags have V4L2_FMT_FLAG_COMPRESSED set
Signed-off-by: John Cox <jc@kynesim.co.uk>
staging/bcm2835-codec: Change the default codec res to 32x32
In order to effectively guarantee that a V4L2_EVENT_SOURCE_CHANGE
event occurs, adopt a default resolution of 32x32 so that it
is incredibly unlikely to be decoding a stream of that resolution
and therefore failing to note a "change" requiring the event.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Add support for decoding interlaced streams
The video decoder can support decoding interlaced streams, so add
the required plumbing to signal this correctly.
The encoder and ISP do NOT support interlaced data, so trying to
configure an interlaced format on those nodes will be rejected.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Correct ENUM_FRAMESIZES stepsize to 2
Being YUV420 formats, the step size is always 2 to avoid part
chroma subsampling.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Return buffers to QUEUED not ERROR state
Should start_streaming fail, or buffers be queued during
stop_streaming, they should be returned to the core as QUEUED
and not (as currently) as ERROR.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835_codec: Log MMAL flags in hex
The flags is a bitmask, so it's far easier to interpret as hex
data instead of decimal.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: bcm2835-codec: Allow custom specified strides/bytesperline.
If the client provides a bytesperline value in try_fmt/s_fmt then
validate it and correct if necessary.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835_codec: Add support for image_fx to deinterlace
Adds another /dev/video node wrapping image_fx doing deinterlace.
Co-developed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
staging/bcm2835-v4l2_codec: Fix for encode selection API
Matches correct behaviour from DECODE and DEINTERLACE
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
staging: bcm2835-codec: Allow decode res changed before STREAMON(CAPTURE)
The V4L2 stateful video decoder API requires that you can STREAMON
on only the OUTPUT queue, feed in buffers, and wait for the
SOURCE_CHANGE event.
This requires that we enable the MMAL output port at the same time
as the input port, because the output port is the one that creates
the SOURCE_CHANGED event.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Do not send buffers to the VPU unless streaming
With video decode we now enable both input and output ports on
the component. This means that buffers will get passed to the VPU
earlier than desired if they are queued befoer STREAMON.
Check that the queue is streaming before sending buffers to the VPU.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: bcm2835-codec: Format changed should trigger drain
When a format changed event occurs, the spec says that it
triggers an implicit drain, and that needs to be signalled
via -EPIPE.
For BCM2835, the format changed event happens at the point
the format change occurs, so no further buffers exist from
before the resolution changed point. We therefore signal the
last buffer immediately.
We don't have a V4L2 available to us at this point, so set
the videobuf2 queue last_buffer_dequeued flag directly.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: bcm2835-codec: Signal the firmware to stop on all changes
The firmware defaults to not stopping video decode if only the
pixel aspect ratio or colourspace change. V4L2 requires us
to stop decoding on any change, therefore tell the firmware
of the desire for this alternate behaviour.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: bcm2835-codec: Queue flushed buffers instead of completing
When a buffer is returned on a port that is disabled, return it
to the videobuf2 QUEUED state instead of DONE which returns it
to the client.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: bcm2835_codec: Correct flushing code for refcounting
Completions don't reference count, so setting the completion
on the first buffer returned and then not reinitialising it
means that the flush function doesn't behave as intended.
Signal the completion when the last buffer is returned.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: bcm2835-codec: Ensure all ctrls are set on streamon
Currently the code was only setting some controls from
bcm2835_codec_set_ctrls, but it's simpler to use
v4l2_ctrl_handler_setup to avoid forgetting to adding new
controls to the list.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: bcm2835-codec: Add support for H&V Flips to ISP
The ISP can do H & V flips whilst resizing or converting
the image, so expose that via V4L2_CID_[H|V]FLIP.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
bcm2835-v4l2-codec: Remove advertised support of VP8
The support for this format by firmware is very limited
and won't be faster than the arm.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Pass V4L2_CID_MPEG_VIDEO_H264_MIN_QP/MAX_QP to bcm2835-v4l2-codec
Following raspberrypi/linux#4704. This is necessary to set up
quantization for variable bitrate to avoid video flickering.
staging/bcm2835-codec: bytesperline for YUV420/YVU420 needs to be 64
Matching https://github.com/raspberrypi/linux/pull/4419, the ISP
block (which is also used on the input of the encoder, and output
of the decoder) needs the base address of all planes to be aligned
to multiples of 32. This includes the chroma planes of YUV420 and
YVU420.
If the height is only a multiple of 2 (not 4), then you get an odd
number of lines in the second plane, which means the 3rd plane
starts at a multiple of bytesperline/2.
Set the minimum bytesperline alignment to 64 for those formats
so that the plane alignment is always right.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Allow a different stride alignment per role
Deinterlace and decode aren't affected in the same way as encode
and ISP by the alignment requirement on 3 plane YUV420.
Decode would be affected, but it always aligns the height up to
a macroblock, and uses the selection API to reflect that.
Add in the facility to set the bytesperline alignment per role.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: vc04_services: codec: Add support for V4L2_PIX_FMT_RGBA32 format
We already support V4L2_PIX_FMT_BGR32 which is the same thing with red
and blue swapped, so it makes sense to include this variant as well.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
bcm2835-codec: Return empty buffers to the VPU instead of queueing to vbuf2
The encoder can skip frames totally should rate control overshoot
the target bitrate too far. In this situation it generates an
output buffer of length 0.
V4L2 treats a buffer of length 0 as an end of stream flag, which is
not appropriate in this case, therefore we can not return that buffer
to the client.
The driver was returning the buffer to videobuf2 in the QUEUED state,
however that buffer was then not dequeued again, so the number of
buffers was reduced each time this happened. In the pathological
case of using GStreamer's videotestsrc in mode 1 for noise, this happens
sufficiently frequently to totally stall the pipeline.
If the port is still enabled then return the buffer straight back to
the VPU rather than to videobuf2.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
vc04_services: bcm2835-codec: Add support for V4L2_PIX_FMT_NV12_COL128
V4L2_PIX_FMT_NV12_COL128 is supported by the ISP and the input of
video_encode, output of video_decode, and both input and output
of the ISP.
Add in the plumbing to support the format on those ports.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
vc04_services: bcm2835-codec: Set crop_height for compressed formats
In particular for the encoder where the CAPTURE format dictates
the parameters given to the codec we need to be able to set the
value passed as the crop_height for the compressed format.
There's no crop available for cropped modes, so always set
crop_height to the requested height.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
vc04_services: bcm2835-codec: Set port format from s_selection
s_selection allows the crop region of an uncompressed pixel
format to be specified, but it wasn't passing the setting on to
the firmware. Depending on call order this would potentially
mean that the crop wasn't actioned.
Set the port format on s_selection if we have a component created.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
bcm2835-codec: /dev/video31 as interface to image_encode JPEG encoder
Signed-off-by: Maxim Devaev <mdevaev@gmail.com>
bcm2835-v4l2-codec: support H.264 5.0 and 5.1 levels
vc04_services: bcm2835-codec: Remove redundant role check
vidioc_try_encoder_cmd checks the role, but the ioctl is disabled
for any roles in which it is invalid.
Remove the redundant check.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
vc04_services: bcm2835-codec: Allow encoder_cmd on ISP and deinterlace
ISP and deinterlace also need a mechanism for passing effectively
an EOS through the pipeline to signal when all buffers have been
processed.
VIDIOC_ENCODER_CMD does exactly this for encoders, so reuse the same
function for ISP and deinterlace.
(VIDIOC_DECODER_CMD is slightly different in that it also passes
details of when and how to stop, so is not as relevant).
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
With the vc-sm-cma driver we can support zero copy of buffers between
the kernel and VPU. Add this support to mmal-vchiq.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add Broadcom VideoCore Shared Memory support.
This new driver allows contiguous memory blocks to be imported
into the VideoCore VPU memory map, and manages the lifetime of
those objects, only releasing the source dmabuf once the VPU has
confirmed it has finished with it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: vcsm-cma: Fix memory leak from not detaching dmabuf
When importing there was a missing call to detach the buffer,
so each import leaked the sg table entry.
Actually the release process for both locally allocated and
imported buffers is identical, so fix them to both use the same
function.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/vc-sm-cma: Avoid log spamming on Pi0/1 over cache alias.
Pi 0/1 use the 0x80000000 cache alias as the ARM also sees the world
through the VPU L2 cache.
vc-sm-cma was trying to ensure it was in an uncached alias (0xc), and
complaining on every allocation if it weren't. Reduce this logging.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
vc-sm-cma: Restore correct cache maintainance operations
We have been using the more expensive flush operations rather than
invalidate and clean since kernel rpi-5.9.y
These are exposed with:
52f1453513 Re-expose some dmi APIs for use in VCSM
But I believe that commit was dropped when (non-cma) vc-sm was dropped,
and didn't get updated when the commit was restored
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
staging: vc04_services: Fix clang14 warning
Insert a break to fix a fallthrough warning from clang14. Since the
fallthrough was to another break, this is a cosmetic change.
See: https://github.com/raspberrypi/linux/issues/5078
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
vc04_services/vc-sm-cma: Handle upstream require vchiq_instance to be passed around
If the RBUF logic is not reset when the kernel starts then there
may be some data left over from any network boot loader. If the
64-byte packet headers are enabled then this can be fatal.
Extend bcmgenet_dma_disable to do perform the reset, but not when
called from bcmgenet_resume in order to preserve a wake packet.
N.B. This different handling of resume is just based on a hunch -
why else wouldn't one reset the RBUF as well as the TBUF? If this
isn't the case then it's easy to change the patch to make the RBUF
reset unconditional.
See: https://github.com/raspberrypi/linux/issues/3850
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Increase the delay before entering the lower power state to 2 seconds
(the maximum allowed) in order to reduce the packet latencies,
particularly for inbound packets.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Display variants are intended as a replacement for the now-deleted
fbtft_device drivers. Drivers can register additional compatible
strings with a custom callback that can make the required changes
to the fbtft_display structure.
Start the ball rolling by adding adafruit18, adafruit18_green and
sainsmart18 displays.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Since the unicam driver was modified to write to a dummy buffer when no
user-supplied buffer is available, it can now write to and return a
buffer even when there's only a single one. Enable this by changing the
min_buffers_needed in the vb2_queue; it will be useful for enabling
still captures without allocating more memory than absolutely necessary.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
The change to retrieve the pixel format always on g_fmt didn't
check whether the native or unpacked version of the format
had been requested, and always returned the packed one.
Correct this so that the packing setting is retained whereever
possible.
Fixes "9d59e89 media: bcm2835-unicam: Re-fetch mbus code from subdev
on a g_fmt call"
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
From when bringing up the driver, there was a check in the isr
to ignore interrupts (claiming them handled) should the driver
not be streaming.
The VPU now will not register a camera driver if it finds a
CSI2 node enabled in device tree, therefore this flawed check is
redundant.
https://github.com/raspberrypi/linux/issues/3602
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Fix commit "media: tc358743: Return an appropriate colorspace from
tc358743_set_fmt" to ensure that the format passed in to set_fmt
is checked to be valid, and reset to the current format if not.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Pi 0&1 pass all ARM accesses through the VPU L2 cache, therefore
the dma-ranges property sets the cache alias bits to other
than the direct alias, hence this WARN was firing.
It was overprotective coding, so assume that everything is OK
with the dma-ranges, and remove the WARN.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The actpwr trigger is a meta trigger that cycles between an inverted
mmc0 and default-on. It is written in a way that could fairly easily
be generalised to support alternative sets of source triggers.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
When streaming with Unicam, the VPU must have a clock frequency of at
least 250Mhz. Otherwise, the input fifos could overrun, causing
image corruption.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
[g|s]_selection pass in a buffer type that needs to be validated
before passing on to the sensor subdev.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
v4l2-compliance throws a failure if the device doesn't advertise
V4L2_CAP_READWRITE but allows read or write operations.
We do support read, so reinstate the flag.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Use bit 27 of the dreq value (the second cell of the DT DMA descriptor)
to request that the WAIT_RESP bit is not set.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Now that the 14bit non-packed Bayer formats are defined, add them
into the supported formats lookup table.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Now that V4L2_PIX_FMT_Y14 and V4L2_PIX_FMT_Y14P are defined,
allow passing 14bit mono data through the peripheral.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Now that V4L2_PIX_FMT_Y12P is defined, allow passing raw 12bit
mono packed data through the peripheral.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Older gcc versions object to = { 0 } initialisation if the first
elemtn in the structure is a substructure.
Use = { } to avoid this compiler warning.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Use the get_mbus_config pad subdev call to allow a source to use
fewer than the number of CSI2 lanes defined in device tree.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add a driver for the Unicam camera receiver block on BCM283x processors.
Compared to the bcm2835-camera driver present in staging, this driver
handles the Unicam block only (CSI-2 receiver), and doesn't depend on
the VC4 firmware running on the VPU.
The commit is made up of a series of changes cherry-picked from the
rpi-5.4.y branch of https://github.com/raspberrypi/linux/ with
additional enhancements, forward-ported to the mainline kernel.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reported-by: kbuild test robot <lkp@intel.com>
When closing the video device, the irs1125 is put in power down state.
To keep V4L2 ctrls and the HW in sync, v4l2_ctrl_handler_setup is
called after power up.
The compound ctrl IRS1125_CID_MOD_PLL however has a default value
of all zeros, which puts the imager into a non responding state.
Thus, this ctrl is not written by the driver into HW after power up.
The userspace has to take care to write senseful data.
Signed-off-by: Markus Proeller <markus.proeller@pieye.org>
Instead of changing the exposure and framerate settings for all sequences,
they can be changed for every sequence individually now. Therefore the
IRS1125_CID_SAFE_RECONFIG ctrl has been removed and replaced by
IRS1125_CID_SAFE_RECONFIG_S<seq_num>_EXPO and *_FRAME ctrls.
The consistency check in the sequence ctrl IRS1125_CID_SEQ_CONFIG
is removed.
Signed-off-by: Markus Proeller <markus.proeller@pieye.org>
Reading data over i2c is done by using i2c_transfer to ensure that this
operation can't be interrupted.
Signed-off-by: Markus Proeller <markus.proeller@pieye.org>
The BRCM PCIe block has controls to enable control of the CLKREQ#
signal by the L1SS, and to gate the refclk with the CLKREQ# input.
These controls are mutually exclusive - the upstream code sets the
latter, but some use cases require the former.
Add a Device Tree property - brcm,enable-l1ss - to switch to the
L1SS configuration.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Upstream Linux deems using output GPIOs to generate IRQs as a bogus
use case, even though the BCM2835 GPIO controller is capable of doing
so. A number of users would like to make use of this facility, so
disable the checks.
See: https://github.com/raspberrypi/linux/issues/2527
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Enabling zswap support in the kernel configuration costs about 1.5MB
of RAM, even when zswap is not enabled at runtime. This cost can be
reduced significantly by deferring initialisation (including pool
creation) until the "enabled" parameter is set to true. There is a
small cost to this in that some initialisation code has to remain in
memory after the init phase, just in case they are needed later,
but the total size increase is negligible.
See: https://github.com/raspberrypi/linux/pull/3432
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
V4L2 wishes to have the codec header bytes in the same buffer as the
first encoded frame, so it does become 1-in 1-out for encoding.
The firmware now has an option to do this, so enable it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
If the firmware hasn't detected a display, the driver would assume
one display was available, but because it had failed to retrieve the
display size it would try to allocate a zero-sized buffer.
Avoid the allocation failure by bailing out early if no display is
found.
See: https://github.com/raspberrypi/linux/issues/3598
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
BCM2711 has 4 DMA channels with a 40-bit address range, allowing them
to access the full 4GB of memory on a Pi 4.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcmn2835_isp is a platform driver dependent on vchiq,
therefore add the load/unload functions for it to vchiq.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Add V4L2_META_FMT_BCM2835_ISP_STATS V4L2 format type.
This new format will be used by the BCM2835 ISP device to return
out ISP statistics for 3A.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
This patch adds MEDIA_BUS_FMT_SENSOR_DATA used by the bcm2835-unicam
driver to support CSI-2 embedded data streams from camera sensors.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Add V4L2_META_FMT_SENSOR_DATA format 4CC.
This new format will be used by the BCM2835 Unicam device to return
out camera sensor embedded data.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Commit f3186dd876 ("spi: Optionally use GPIO descriptors for CS GPIOs")
amended of_spi_parse_dt() to always set SPI_CS_HIGH for SPI slaves whose
Chip Select is defined by a "cs-gpios" devicetree property.
This change breaks drivers whose probe functions set the mode field of
the spi_device because in doing so they clear the SPI_CS_HIGH flag.
Fix by setting SPI_CS_HIGH in spi_setup (under the same conditions as
in of_spi_parse_dt()).
See also: 83b2a8fe43 ("spi: spidev: Fix CS polarity if GPIO descriptors are used")
Fixes: f3186dd876 ("spi: Optionally use GPIO descriptors for CS GPIOs")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
SQUASH: spi: Demote SPI_CS_HIGH warning to KERN_DEBUG
This warning is unavoidable from a client's perspective and
doesn't indicate anything wrong (just surprising).
SQUASH with "spi: use_gpio_descriptor fixup moved to spi_setup"
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
This driver is for the HEVC/H265 decoder block on the Raspberry
Pi 4, and conforms to the V4L2 stateless decoder API.
Signed-off-by: John Cox <jc@kynesim.co.uk>
staging: media: rpivid: Select MEDIA_CONTROLLER and MEDIA_CONTROLLER_REQUEST_API
MEDIA_CONTROLLER_REQUEST_API is a hidden option. If rpivid depends on it,
the user would need to first enable another driver that selects
MEDIA_CONTROLLER_REQUEST_API, and only then rpivid would become available.
By selecting it instead of depending on it, it becomes possible to enable
rpivid without having to enable other potentially unnecessary drivers.
Signed-off-by: Hristo Venev <hristo@venev.name>
rpivid_h265: Fix width/height typo
Signed-off-by: popcornmix <popcornmix@gmail.com>
rpivid_h625: Fix build warnings
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
staging: rpivid: Fix crash when CMA alloc fails
If realloc to increase coeff size fails then attempt to re-allocate
the original size. If that also fails then flag a fatal error to abort
all further decode.
Signed-off-by: John Cox <jc@kynesim.co.uk>
rpivid: Request maximum hevc clock
Query maximum and minimum clock from driver
and use those
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
rpivid: Switch to new clock api
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
rpivid: Only clk_request_done once
Fixes: 25486f49bf
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
media: rpivid: Remove the need to have num_entry_points set
VAAPI H265 has num entry points but never sets it. Allow a VAAPI
shim to work without requiring rewriting the VAAPI driver.
num_entry_points can be calculated from the slice_segment_addr
of the next slice so delay processing until we have that.
Also includes some minor cosmetics.
Signed-off-by: John Cox <jc@kynesim.co.uk>
media: rpivid: Convert to MPLANE
Use multi-planar interface rather than single plane interface. This
allows dmabufs holding compressed data to be resized.
Signed-off-by: John Cox <jc@kynesim.co.uk>
media: rpivid: Add an enable count to irq claim Qs
Add an enable count to the irq Q structures to allow the irq logic to
block further callbacks if resources associated with the irq are not
yet available.
Signed-off-by: John Cox <jc@kynesim.co.uk>
media: rpivid: Add a Pass0 to accumulate slices and rework job finish
Due to overheads in assembling controls and requests it is worth having
the slice assembly phase separate from the h/w pass1 processing. Create
a queue to service pass1 rather than have the pass1 finished callback
trigger the next slice job.
This requires a rework of the logic that splits up the buffer and
request done events. This code contains two ways of doing that, we use
Ezequiel Garcias <ezequiel@collabora.com> solution, but expect that
in the future this will be handled by the framework in a cleaner manner.
Fix up the handling of some of the memory exhaustion crashes uncovered
in the process of writing this code.
Signed-off-by: John Cox <jc@kynesim.co.uk>
media: rpivid: Map cmd buffer directly
It is unnecessary to have a separate dmabuf to hold the cmd buffer.
Map it directly from the kmalloc.
Signed-off-by: John Cox <jc@kynesim.co.uk>
media: rpivid: Improve values returned when setting output format
Guess a better value for the compressed bitstream buffer size
Signed-off-by: John Cox <jc@kynesim.co.uk>
media: rpivid: Improve stream_on/off conformance & clock setup
Fix stream on & off such that failures leave the driver in the correct
state. Ensure that the clock is on when we are streaming and off when
all contexts attached to this device have stopped streaming.
Signed-off-by: John Cox <jc@kynesim.co.uk>
media: rpivid: Improve SPS/PPS error handling/validation
Move size and width checking from bitstream processing to control
validation
Signed-off-by: John Cox <jc@kynesim.co.uk>
media: rpivid: Fix H265 aux ent reuse of the same slot
It is legitimate, though unusual, for an aux ent associated with a slot
to be selected in phase 0 before a previous selection has been used and
released in phase 2. Fix such that if the slot is found to be in use
that the aux ent associated with it is reused rather than an new aux
ent being created. This fixes a problem where when the first aux ent
was released the second was lost track of.
This bug spotted in Nick's testing. It may explain some other occasional,
unreliable decode error reports where dmesg included "Missing DPB AUX
ent" logging.
Signed-off-by: John Cox <jc@kynesim.co.uk>
media: rpivid: Update to compile with new hevc decode params
DPB entries have moved from slice params to the new decode params
attribute - update to deal with this. Also fixes fallthrough
warnings which seem to be new in 5.14.
Signed-off-by: John Cox <jc@kynesim.co.uk>
media: rpivid: Make slice ctrl dynamic
Allows the user to submit a whole frames worth of slice headers in
one lump along with a single bitstream dmabuf for the whole lot.
This saves potentially a lot of bitstream copying.
Signed-off-by: John Cox <jc@kynesim.co.uk>
media: rpivid: Only create aux entries for H265 if needed
Only create aux entries of mv info for frames where that info might
be used by a later frame. This saves some memory bandwidth and
potentially some memory.
Signed-off-by: John Cox <jc@kynesim.co.uk>
media: rpivid: Avoid returning EINVAL to a G_FMT ioctl
V4L2 spec says that G/S/TRY_FMT IOCTLs should never return errors for
anything other than wrong buffer types. Improve the capture format
function such that this is so and unsupported values get converted
to supported ones properly.
Signed-off-by: John Cox <jc@kynesim.co.uk>
media: rpivid: Remove unused ctx state variable and defines
Remove unused ctx state tracking variable and associated defines.
Their presence implies they might be used, but they aren't.
Signed-off-by: John Cox <jc@kynesim.co.uk>
media: rpivid: Ensure IRQs have completed before uniniting context
Before uniniting the decode context sync with the IRQ queues to ensure
that decode no longer has any buffers in use. This fixes a problem that
manifested as ffmpeg leaking CMA buffers when it did a stream off on
OUTPUT before CAPTURE, though in reality it was probably much more
dangerous than that.
Signed-off-by: John Cox <jc@kynesim.co.uk>
media: rpivid: remove min_buffers_needed from src queue
Remove min_buffers_needed=1 from src queue init. Src buffers are bound
to media requests therefore this setting is not needed and generates
a WARN in kernel 5.16.
Signed-off-by: John Cox <jc@kynesim.co.uk>
rpivid: Use clk_get_max_rate()
The driver was using clk_round_rate() to figure out the maximum clock
rate that was allowed for the HEVC clock.
Since we have a function to return it directly now, let's use it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
media: rpivid: Apply V4L2 stateless API changes
media: rpivid: Fix fallthrough warning
Replace old-style /* FALLTHRU */ with fallthrough;
Signed-off-by: John Cox <jc@kynesim.co.uk>
media: rpivid: Set min value as well as max for HEVC_DECODE_MODE
As only one value can be accepted set both min and max to that value.
Signed-off-by: John Cox <jc@kynesim.co.uk>
media: rpivid: Accept ANNEX_B start codes
Allow the START_CODE control to take ANNEX_B as a value. This makes no
difference to any part of the decode process as the added bytes are in
data that we ignore. This helps my testing and may help userland code
that expects to send those bytes.
Signed-off-by: John Cox <jc@kynesim.co.uk>
rpivid: Convert to new clock rate API
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
This is probably not the API we will want to add, but it
should show what semantics are needed by drivers.
The goal is to allow the OUTPUT (aka source) buffer and the
controls associated to a request to be released from the request,
and in particular return the OUTPUT buffer back to userspace,
without signalling the media request fd.
This is useful for devices that are able to pre-process
the OUTPUT buffer, therefore able to release it before
the decoding is finished. These drivers should signal
the media request fd only after the CAPTURE buffer is done.
Tested-by: John Cox <jc@kynesim.co.uk>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Some of the Broadcom codec blocks use a column based YUV4:2:0 image
format, so add the documentation and defines for both 8 and 10 bit
versions.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The DT bindings description of the Brcmstb PCIe device is described. This
node can be used by almost all Broadcom settop box chips, using
ARM, ARM64, or MIPS CPU architectures.
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
When symbols from overlays are added to the live tree their paths must
be rebased. The translated symbol is normally the result of joining
the fragment-relative path (with a leading "/") to the target path
(either copied directly from the "target-path" property or resolved
from the phandle). This translation fails when the target is the root
node (a common case for Raspberry Pi overlays) because the resulting
path starts with a double slash. For example, if target-path is "/" and
the fragment adds a node called "newnode", the label associated with
that node will be assigned the path "//newnode", which can't be found
in the tree.
Fix the failure case by explicitly replacing a target path of "/" with
an empty string.
Fixes: d1651b03c2 ("of: overlay: add overlay symbols to live device tree")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The definition of compat_ptr is now common for most platforms, but
requires the inclusion of <linux/compat.h>.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
A failure in gpiochip_irqchip_add leads to a leak of a gpiochip. Fix
the leak with the use of devm_gpiochip_add_data.
Fixes: 85ae9e512f ("pinctrl: bcm2835: switch to GPIOLIB_IRQCHIP")
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
vchiq kernel clients are now instantiated as platform drivers rather
than using DT, but the children of the vchiq interface may still
benefit from access to DT properties. Give them the option of a
a sub-node of the vchiq parent for configuration and to allow
them to be disabled.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The IMA (Integrity Measurement Architecture) looks for a TPM (Trusted
Platform Module) having been registered when it initialises; otherwise
it assumes there is no TPM. It has been observed on BCM2835 that IMA
is initialised before TPM, and that initialising the BCM2835 clock
driver before the firmware driver has the effect of reversing this
order.
Change the firmware driver to initialise at core_initcall, delaying the
BCM2835 clock driver to postcore_initcall.
See: https://github.com/raspberrypi/linux/issues/3291https://github.com/raspberrypi/linux/pull/3297
Signed-off-by: Luke Hinds <lhinds@redhat.com>
Co-authored-by: Phil Elwell <phil@raspberrypi.org>
vchiq on Pi4 is no longer under the soc node, therefore it
doesn't get the dma-ranges for the VPU.
Switch to using the configuration of the old dma controller as
that will set the dma-ranges correctly.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The VCHIQ driver now loads the audio, camera, codec, and vc-sm
drivers as platform drivers. However they were not being given
the correct DMA configuration.
Call of_dma_configure with the parent (VCHIQ) parameters to be
inherited by the child.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
For performance/power it is beneficial to adjust gpu clocks with arm clock.
This is how the downstream cpufreq driver works
Signed-off-by: popcornmix <popcornmix@gmail.com>
Setting the v3d clock to low value allows firmware to handle dvfs in case
where v3d hardware is not being actively used (e.g. console use).
Signed-off-by: popcornmix <popcornmix@gmail.com>
Add device tree entries and code to allow the specification of
the lighting modes for the LED's on the ethernet connector.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
net:phy:2711 Change the default ethernet LED actions
This should return default behaviour back to that of previous
releases.
Following the same pattern as bcm2835-camera and bcm2835-audio,
register the V4L2 codec driver as a platform driver
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Following the same pattern as bcm2835-camera and bcm2835-audio,
register the vcsm-cma driver as a platform driver
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The irq_fence and done_fence are given a reference that is never
released. The necessary dma_fence_put()s seem to have been
deleted in error in an earlier commit.
Fixes: 0b73676836b2 ("drm/v3d: Clock V3D down when not in use.")
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The v3d driver currently encounters a lot of MMU PTE exceptions, so
only log the first to avoid swamping the kernel log.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The Infineon IRS1125 is a time of flight depth sensor that
has a CSI-2 interface.
Add a V4L2 subdevice driver for this device.
Signed-off-by: Markus Proeller <markus.proeller@pieye.org>
After the decision to use bcm2711 compatible for upstream, we should
switch all accepted compatibles to bcm2711. So we can boot with
one DTB the down- and the upstream kernel.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
The cherry-pick of the patch that added the greyworld AWB mode
was incomplete. Fix it up.
Fixes: b3ef481fe2 "staging: bcm2835-camera: Add greyworld AWB mode"
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add name for greyworld to white_balance preset names.
This patch previously applied to v4l2-ctrl.c but that was split
and deleted.
Signed-off-by: John Cox <jc@kynesim.co.uk>
This is mainly used for the NoIR camera which has no IR
filter and can completely confuse normal AWB presets.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Adds a simple greyworld white balance preset, mainly for use
with cameras without an IR filter (eg Raspberry Pi NoIR)
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
dt-bindings: media: i2c: Add IMX519 CMOS sensor binding
Add YAML device tree binding for IMX519 CMOS image sensor, and
the relevant MAINTAINERS entries.
Signed-off-by: Lee Jackson <info@arducam.com>
media: i2c: Add driver for IMX519 sensor
Adds a driver for the 16MPix IMX519 CSI2 sensor.
Whilst the sensor supports 2 or 4 CSI2 data lanes, this driver
currently only supports 2 lanes.
The following Bayer modes are currently available:
4656x3496 10-bit @ 10fps
3840x2160 10-bit (cropped) @ 21fps
2328x1748 10-bit (binned) @ 30fps
1920x1080 10-bit (cropped/binned) @ 60fps
1280x720 10-bit (cropped/binned) @ 120fps
Signed-off-by: Lee Jackson <info@arducam.com>
media: i2c: imx519: Advertise embedded data node on media pad 1
This commit updates the imx519 driver to adverise support for embedded
data streams.
The imx519 sensor subdevice overloads the media pad to differentiate
between image stream (pad 0) and embedded data stream (pad 1) when
performing the v4l2_subdev_pad_ops functions.
Signed-off-by: Lee Jackson <info@arducam.com>
media: i2c: imx519: Sensor should report RAW color space
Tested on Raspberry Pi running libcamera.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
media: i2c: Update imx519 Kconfig entry
Bring the IMX519 Kconfig declaration in line with the upstream entries.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
dt-bindings: media: i2c: Add IMX477 CMOS sensor binding
Add YAML device tree binding for IMX477 CMOS image sensor.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: Add driver for Sony IMX477 sensor
Adds a driver for the 12MPix Sony IMX477 CSI2 sensor.
Whilst the sensor supports 2 or 4 CSI2 data lanes, this driver
currently only supports 2 lanes.
The following Bayer modes are currently available:
4056x3040 12-bit @ 10fps
2028x1520 12-bit (binned) @ 40fps
2028x1050 12-bit (cropped/binned) @ 50fps
1012x760 10-bit (scaled) @ 120 fps
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Add support for adaptive frame control
Use V4L2_CID_EXPOSURE_AUTO_PRIORITY to control if the driver should
automatically adjust the sensor frame length based on exposure time,
allowing variable frame rates and longer exposures.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Return correct result on sensor id verification
The test should return -EIO if the register read id does not match
the expected sensor id.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Parse and register properties
Parse device properties and register controls for them using the V4L2
fwnode properties helpers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
media: i2c: imx477: Selection compliance fixes
To comply with the intended usage of the V4L2 selection target when
used to retrieve a sensor image properties, adjust the rectangles
returned by the imx477 driver.
The top/left crop coordinates of the TGT_CROP rectangle were set to
(0, 0) instead of (8, 16) which is the offset from the larger physical
pixel array rectangle. This was also a mismatch with the default values
crop rectangle value, so this is corrected. Found with v4l2-compliance.
While at it, add V4L2_SEL_TGT_CROP_BOUNDS support: CROP_DEFAULT and
CROP_BOUNDS have the same size as the non-active pixels are not readable
using the selection API. Found with v4l2-compliance.
This commit mirrors 543790f777 done for
the imx219 sensor.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Remove auto frame length adjusting
The V4L2_CID_EXPOSURE_AUTO_PRIORITY was used to let the sensor control
frame length (effectively framerate) based on the requested exposure
time requested. Remove this feature as it is never used, and goes
against how V4L2 likes to handle exposure and vblank controls.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Add very long exposure control to the driver
Add support for very long exposures by using the exposure multiplier
register. Userland does not need to pass any additional controls to
enable long exposures, it simply requests a larger vblank to extend the
exposure control range appropriately.
Currently, since hblank is fixed, a maximum of approximately 124 seconds
of exposure time can be used. In a future change, hblank could also be
controlled in userland to give over 200 seconds of exposure time.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Fix crop height for 2028x1080 mode
The crop height for this mode was set at 2600 lines, it should be 2160
lines instead.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Replace existing 1012x760 mode
The existing 1012x760 120 fps mode has significant IQ problem using
the internal sensor scaler. Replace this mode with a 1332x990 120 fps
mode instead. This new mode has a smaller field of view, but does not
suffer from the bad IQ of the original mode.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Remove internal v4l2_mbus_framefmt from the state
The only field in this struct that is used is the format code, so
replace the struct with this single field.
Save the format code in imx477_set_pad_format() when setting up a new
mode so that imx477_get_pad_format() performs the right lookup.
Otherwise, this caused a bug where the mode lookup occurred on the
12-bit table rather than the 10-bit table.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Remove unused function parameter
The struct imx477 *ctrl parameter is not used in the function
imx477_adjust_exposure_range(), so remove it.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Fix for long exposure limit calculations
Do not scale IMX477_EXPOSURE_OFFSET with the long exposure factor during
the limit calculations. This allows larger exposure times, and does seem to be
what the sensor is doing internally.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Extend driver to support imx378 sensor
The imx378 sensor is almost identical to the imx477 and can be
supported as a "compatible" sensor with just a few extra register
writes.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
media: i2c: imx477: Fix framerates for 1332x990 mode
The imx477 driver's line length for this mode had not been updated to
the value supplied to us by the sensor manufacturer. With this
correction the sensor delivers the framerates that are expected.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
media: i2c: imx477: Allow control of on-sensor DPC
A module parameter "dpc_enable" is added to allow the control of the
sensor's on-board DPC (Defective Pixel Correction) function.
This is a global setting to be configured before using the sensor;
there is no intention that this would ever be changed on-the-fly.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
media: i2c: imx477: Sensor should report RAW color space
Tested on Raspberry Pi running libcamera.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
media: i2c: imx477: Add vsync trigger_mode parameter
trigger_mode == 0 (default) => no effect / no registers written
trigger_mode == 1 => source
trigger_mode == 2 => sink
This can be set e.g. in /boot/cmdline.txt as imx477.trigger_mode=N
Signed-off-by: Jonas Jacob <jonas.jacob@neocortexvision.com>
media: i2c: Update imx477 Kconfig entry
Bring the IMX477 Kconfig declaration in line with upstream entries.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
media: i2c: imx477: Correct minimum exposure lines
The minimum number of exposure lines value (IMX477_EXPOSURE_MIN) was
previously 20 but this is not correct. The datasheet is not completely
explicit, however the new value of 4 has been tested with all the
sensor modes supported by this driver, and matches the lowest exposure
value of 114us that could be achieved wtih Raspberry Pi's legacy
firmware driver.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
media: i2c: imx477: Allow dynamic horizontal blanking control
Currently, the V4L2_CID_HBLANK control is marked as read-only. Remove this
restriction and allow userland to modify the control if needed.
Set the maximum limit of the line length to 0xfff0.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Reset hblank on mode switch
Reset the hblank control to the minimum value on every mode switch. This is to
account for userland instances that do not yet control hblank, otherwise it
gets set to a non-optimal value.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Do not unconditionally adjust hblank and vblank limits
On a mode change, only call imx477_set_framing_limits() to adjust the hblank
and vblank limits if the new mode is different from the existing mode. This
preserves any manual control values the user might have set.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx258: Remove unused defines
The IMX258_FLL_* defines are unused. Remove them.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: i2c: imx258: Make image geometry meet sensor requirements
The output image is defined as being 4208x3118 pixels in size.
Y_ADD_STA register was set to 0, and Y_ADD_END to 3118, giving
3119 lines total.
The datasheet lists a requirement for Y_ADD_STA to be a multiple
of a power of 2 depending on binning/scaling mode (2 for full pixel,
4 for x2-bin/scale, 8 for (x2-bin)+(x2-subsample) or x4-bin, or 16
for (x4-bin)+(x2-subsample)).
(Y_ADD_END – Y_ADD_STA + 1) also has to be a similar power of 2.
The current configuration for the full res modes breaks that second
requirement, and we can't increase Y_ADD_STA to 1 to retain exactly
the same field of view as that then breaks the first requirement.
For the binned modes, they are worse off as 3118 is not a multiple of
4.
Increase the main mode to 4208x3120 so that it is the same FOV as the
binned modes, with Y_ADD_STA at 0.
Fix Y_ADD_STA and Y_ADD_END for the binned modes so that they meet the
sensor requirements.
This does change the Bayer order as the default configuration is for
H&V flips to be enabled, so readout is from Y_STA_END to Y_ADD_STA,
and this patch has changed Y_STA_END.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: i2c: imx258: Disable digital cropping on binned modes
The binned modes set DIG_CROP_X_OFFSET and DIG_CROP_IMAGE_WIDTH
to less than the full image, even though the image being captured
is meant to be a scaled version of the full array size.
Reduce X_OFFSET to 0, and increase IMAGE_WIDTH to the full array.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: i2c: imx258: Implement HFLIP and VFLIP controls.
The sensor supports H & V flips, so implement the relevant controls.
Note that the Bayer order changes with these flips, therefore
they set the V4L2_CTRL_FLAG_MODIFY_LAYOUT property.
As we now support flips, remove the restriction of the sensor only
probing if rotated 180 degrees, but do take that value and initialise
VFLIP and HFLIP based on it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: i2c: imx258: Remove redundant I2C writes.
Registers 0x0202 and 0x0203 are written via the control handler
for V4L2_CID_EXPOSURE, so are not needed from the mode lists.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: i2c: imx258: Add regulator control
The device tree bindings define the relevant regulators for the
sensor, so update the driver to request the regulators and control
them at the appropriate times.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: i2c: imx258: Make V4L2_CID_VBLANK configurable.
The values and ranges of V4L2_CID_VBLANK are all computed,
so there is no reason for it to be a read only control.
Remove the register values from the mode lists, add the
handler, and remove the read only flag.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: i2c: imx258: Register the ctrls from fwnode properties
Use v4l2_ctrl_new_fwnode_properties to register the standard
fwnode properties for the driver.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: i2c: imx258: Add support for 24MHz clock
There's no reason why the clock must be 19.2MHz and nothing
else (indeed this isn't even a frequency listed in the datasheet),
so add support for 24MHz as well.
The PLL settings result in slightly different link frequencies,
so parameterise those.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: i2c: imx258: Add support for running on 2 CSI data lanes
Extends the driver to also support 2 data lanes.
Frame rates are obviously more restricted on 2 lanes, but some
hardware simply hasn't wired more up.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: i2c: imx258: Follow normal V4L2 behaviours for clipping exposure
V4L2 sensor drivers are expected are expected to clip the supported
exposure range based on the VBLANK configured.
IMX258 wasn't doing that as register 0x350 (FRM_LENGTH_CTL)
switches it to a mode where frame length tracks coarse exposure time.
Disable this mode and clip the range for V4L2_CID_EXPOSURE appropriately
based on V4L2_CID_VBLANK.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: i2c: imx258: Add get_selection for pixel array information
Libcamera requires the cropping information for each mode, so
add this information to the driver.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: i2c: imx258: Allow configuration of clock lane behaviour
The sensor supports the clock lane either remaining in HS mode
during frame blanking, or dropping to LP11.
Add configuration of the mode via V4L2_MBUS_CSI2_NONCONTINUOUS_CLOCK.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: i2c: imx258: Correct max FRM_LENGTH_LINES value
The data sheet states that the maximum value for registers
0x0340/0x0341 FRM_LENGTH_LINES is 65525(decimal), not the
0xFFFF defined in this driver. Correct this limit.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: i2c: imx258: Add support for long exposure modes
The sensor has a register CIT_LSHIFT which extends the exposure
and frame times by the specified power of 2 for longer
exposure times.
Add support for this by configuring this register via V4L2_CID_VBLANK
and extending the V4L2_CID_EXPOSURE range accordingly.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: i2c: imx258: Issue reset before starting streaming
Whilst not documented, register 0x0103 bit 0 is the soft
reset for the sensor, so send it before trying to configure
the sensor.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: i2c: imx258: Set pixel_rate range to the same as the value
With a read only control there is limited point in advertising
a minimum and maximum for the control, so change to set the
value, min, and max all to the selected pixel rate.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: i2c: imx258: Support faster pixel rate on binned modes
With the binned modes, there is little point in faithfully
reproducing the horizontal line length of 5352 pixels on the CSI2
bus, and the FIFO between the pixel array and MIPI serialiser
allows us to remove that dependency.
Allow the pixel array to run with the normal settings, with the MIPI
serialiser at half the rate. This requires some additional
information for the link frequency to pixel rate function that
needs to be added to the configuration tables.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: dt-bindings: imx258: Add alternate compatible strings
There are a number of variants of the imx258 modules that can not
be differentiated at runtime, so add compatible strings for them.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: i2c: imx258: Change register settings for variants of the sensor
Sony have advised that there are variants of the IMX258 sensor which
require slightly different register configuration to the mainline
imx258 driver defaults.
There is no available run-time detection for the variant, so add
configuration via the DT compatible string.
The Vision Components imx258 module supports PDAF, so add the
register differences for that variant
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Users have reported log spam created by "Event Ring Full" xHC event
TRBs. These are caused by interrupt latency in conjunction with a very
busy set of devices on the bus. The errors are benign, but throughput
will suffer as the xHC will pause processing of transfers until the
event ring is drained by the kernel. Expand the number of event TRB slots
available by increasing the number of event ring segments in the ERST.
Controllers have a hardware-defined limit as to the number of ERST
entries they can process, so make the actual number in use
min(ERST_MAX_SEGS, hw_max).
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Some combinations of Pi 4Bs and Ethernet switches don't reliably get a
DCHP-assigned IP address, leaving the unit with a self=assigned 169.254
address. In the failure case, the Pi is left able to receive packets
but not send them, suggesting that the MAC<->PHY link is getting into
a bad state.
It has been found empirically that skipping a reset step by the genet
driver prevents the failures. No downsides have been discovered yet,
and unlike the forced renegotiation it doesn't increase the time to
get an IP address, so the workaround is enabled by default; add
genet.skip_umac_reset=n
to the command line to disable it.
See: https://github.com/raspberrypi/linux/issues/3108
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
These wireless mouse/keyboard combo remote control devices specify
multiple "wheel" events in their report descriptors. The wheel events
are incorrectly defined and apparently map to accelerometer data, leading
to spurious mouse scroll events being generated at an extreme rate when
the device is moved.
As a workaround, use HID_QUIRK_INCREMENT_USAGE_ON_DUPLICATE to mask
feeding the extra wheel events to the input subsystem.
See: https://github.com/raspberrypi/firmware/issues/1189
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Based on the gpiomem driver, allow mapping of the decoder register
spaces such that userspace can access control/status registers.
This driver is intended for use with a custom ffmpeg backend accelerator
prior to a v4l2 driver being written.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
driver: char: rpivid: Destroy the legacy device on remove
The legacy name support created a new device that was never destroyed.
If the driver was unloaded and reloaded, it failed due to the
device already existing.
Fixes: "75f1d14 driver: char: rpivid - also support legacy name"
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
driver: char: rpivid: Clean up error handling use of ERR_PTR/IS_ERR
The driver used an unnecessary intermediate void* variable so it
only called ERR_PTR once to convert to the error value.
Switch to converting as the error arises to remove these intermediate
variables.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
driver: char: rpivid: Add error handling to the legacy device load
The return value from device_create for the legacy device was never
checked or handled. Add the required error handling.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
driver: char: rpivid: Fix coding style whitespace issues.
Makes checkpatch happier.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
driver: char: rpimem: Add SPDX licence header.
Stops checkpatch complaining.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
driver: char: rpivid: Fix access to freed memory
The error path during probe frees the private memory block, and
then promptly dereferences it to log an error message.
Use the base device instead of the pointer to it in the private
structure.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
driver: char: rpivid: Remove legacy name support
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
driver: char: rpivid: Don't map more than wanted
Limit mappings to the permitted range, but don't map more than asked
for otherwise we walk off the end of the allocated VMA.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
My various attempts at re-enabling runtime PM have failed, so just
crank the clock down when V3D is idle to reduce power consumption.
Signed-off-by: Eric Anholt <eric@anholt.net>
The BCM2835 I2C blocks have a register to set the clock-stretch
timeout - how long the device is allowed to hold SCL low - in bus
cycles. The current driver doesn't write to the register, therefore
the default value of 64 cycles is being used for all devices.
Set the timeout to the value recommended for SMBus - 35ms.
See: https://github.com/raspberrypi/linux/issues/3064
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Must be called in a non-atomic context, after the endpoint
has been registered with the hardware via xhci_add_endpoint
and before the first URB is submitted for the endpoint.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
xHCI caches device and endpoint data after the interface is configured,
so an explicit command needs to be issued for any device driver wanting
to alter the polling interval of an endpoint.
Add usb_fixup_endpoint() to allow drivers to do this. The fixup must be
called after calculating endpoint bandwidth requirements but before any
URBs are submitted.
If polling intervals are shortened, any bandwidth reservations are no
longer valid but in practice polling intervals are only ever relaxed.
Limit the scope to interrupt transfers for now.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
There are several warts surrounding bcmgenet_mii_probe() as this
function is called from ndo_open, but it's calling registration-type
functions. The probe should be called at probe time and refactored
such that the PHY device data can be extracted to limit the scope
of this flag to Broadcom PHYs.
For now, pass this flag in as it puts our attached PHY into a low-power
state when disconnected.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Set defaults for TX and RX packet coalescing to be equivalent to:
# ethtool -C eth0 tx-frames 10
# ethtool -C eth0 rx-usecs 50
This may be something we want to set via DT parameters in the
future.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The HWRNG on the BCM2838 is compatible to iproc-rng200, so add the
support to this driver instead of bcm2835-rng.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
hwrng: iproc-rng200: Correct SoC name
The Pi 4 SoC is called BCM2711, not BCM2838.
Fixes: "hwrng: iproc-rng200: Add BCM2838 support"
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The legacy peripherals can only address the first gigabyte of RAM, so
ensure that DMA allocations are restricted to that region.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The ioremapping creates mappings within the vmalloc area. The
equivalent early function, create_mapping, now checks that the
requested explicit virtual address is between VMALLOC_START and
VMALLOC_END. As there is no reason to have any correlation between
the physical and virtual addresses, put the required mappings at
VMALLOC_START and above.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
On error, vchiq_mmal_component_init could leave the
event context allocated for ports.
Clean them up in the error path.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
vchiq_mmal_component_init calls init_event_context for the
control port, but vchiq_mmal_component_finalise didn't free
it, causing a memory leak..
Add the free call.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
mmal_parameters.h hasn't been updated to reflect additions made
over the last few years. Update it to reflect the currently
supported parameters.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The list of formats was copied before Bayer support was added.
The ISP supports Bayer and is being supported by the bcm2835_codec
driver, so add in the encodings for them.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The MMAL client_component field is used with the event
mechanism to allow the client to identify the component for
which the event is generated.
The field is only 32bits in size, therefore we can't use a
pointer to the component in a 64 bit kernel.
Component handles are already held in an array per VCHI
instance, so use the array index as the client_component handle
to avoid having to create a new IDR for this purpose.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
videobuf2 only allowed exporting a dmabuf as a file descriptor,
but there are instances where having the struct dma_buf is
useful within the kernel.
Split the current implementation into two, one step which
exports a struct dma_buf, and the second which converts that
into an fd.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Add the ability to send data to ports. This only supports
zero copy mode as the required bulk transfer setup calls
are not done.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
(Preparation for the codec driver).
The codec uses the event mechanism to report things such as
resolution changes. It is signalled by the cmd field of the buffer
being non-zero.
Add support for passing this information out to the client.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Fixes up a checkpatch error "Avoid using bool structure members
because of possible alignment issues".
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
When calling tc358743_set_fmt, the code was calling tc358743_get_fmt
to choose a valid format. However that sets the colorspace
based on what was read back from the chip. When you set the format,
then the driver would choose and program the colorspace based
on the format code.
The result was that if you called try or set format for UYVY
when the current format was RGB3 then you would get told sRGB,
and try RGB3 when current was UYVY and you would get told
SMPTE170M.
The value programmed into the chip is determined by this driver,
therefore there is no need to read back the value. Return the
colorspace based on the format set/tried instead.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Document the DT bindings for the CSI2/CCP2 receiver peripheral
(known as Unicam) on BCM283x SoCs.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Acked-by: Rob Herring <robh@kernel.org>
New helper defines that allow printing of a FOURCC using
printf(V4L2_FOURCC_CONV, V4L2_FOURCC_CONV_ARGS(fourcc));
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The ADV7282M can support YPbPr on AIN1-3, but this was
not selectable from the driver. Add it to the list of
supported input modes.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The hardware default is differential CVBS on AIN1 & 2, which
isn't very useful.
Select the first input that is defined as valid for the
chip variant (typically CVBS_AIN1).
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The probe for the TC358743 reads the CHIPID register from
the device and compares it to the expected value of 0.
If the I2C request fails then that also returns 0, so
the driver loads thinking that the device is there.
Generally I2C communications are reliable so there is
limited need to check the return value on every transfer,
therefore only amend the one read during probe to check
for I2C errors.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Adds register setups for running the CSI lanes at 972Mbit/s,
which allows 1080P50 UYVY down 2 lanes.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The existing fixed value of 16 worked for UYVY 720P60 over
2 lanes at 594MHz, or UYVY 1080P60 over 4 lanes. (RGB888
1080P60 needs 6 lanes at 594MHz).
It doesn't allow for lower resolutions to work as the FIFO
underflows.
374 is required for 1080P24-30 UYVY over 2 lanes @ 972Mbit/s, but
>374 means that the FIFO underflows on 1080P50 UYVY over 2 lanes
@ 972Mbit/s.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Add the ability to interpret the high bits of the dreq specifier as
flags to be included in the DMA_CS register. The motivation for this
change is the ability to set the DISDEBUG flag for SD card transfers
to avoid corruption when using the VPU debugger.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The bInterval is set to 4 (i.e. 8 microframes => 1ms) and the only bit
that the driver pays attention to is "link was reset". If there's a
flapping status bit in that endpoint data, (such as if PHY negotiation
needs a few tries to get a stable link) then polling at a slower rate
would act as a de-bounce.
See: https://github.com/raspberrypi/linux/issues/2447
The driver already reported the firmware build date during probe.
The mailbox calls have been extended to also report the variant
1 = standard start.elf
2 = start_x.elf (includes camera stack)
3 = start_db.elf (includes assert logging)
4 = start_cd.elf (cutdown version for smallest memory footprint).
Log the variant during probe.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
firmware: raspberrypi: Report the fw git hash during probe
The firmware can now report the git hash from which it was built
via the mailbox, so report it during probe.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Ethernet cables with faulty or missing pairs (specifically pairs C and
D) allow auto-negotiation to 1000Mbs, but do not support the successful
establishment of a link. Add a DT property, "microchip,downshift-after",
to configure the number of auto-negotiation failures after which it
falls back to 100Mbs. Valid values are 2, 3, 4, 5 and 0, where 0 means
never downshift.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Step wise governor increases the mitigation level when the temperature
goes above a threshold and will decrease the mitigation when the
temperature falls below the threshold. If it were a case, where the
temperature hovers around a threshold, the mitigation will be applied
and removed at every iteration. This reaction to the temperature is
inefficient for performance.
The use of hysteresis temperature could avoid this ping-pong of
mitigation by relaxing the mitigation to happen only when the
temperature goes below this lower hysteresis value.
Signed-off-by: Ram Chandrasekar <rkumbako@codeaurora.org>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Avoid a hard userspace ABI change by adding a compatible get_throttled
sysfs entry. Its value is now feed by the GET_THROTTLED requests of the
new hwmon driver. The first access to get_throttled will generate
a warning.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Enable EEE mode as soon as possible after connecting to the PHY, and
before phy_start. This avoids a second link negotiation, which speeds
up booting and stops the interface failing to become ready.
See: https://github.com/raspberrypi/linux/issues/2437
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
As of 4.18, a firmware that implements the update_connect_params
method but doesn't claim to support roaming causes an error. We
disabled firmware roaming in 4.4 [1] because it appeared to
prevent disconnects, but let's try with the current firmware to see
if things have improved.
[1] dd91880117
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
ad83c7cb2f ("irqchip/irq-bcm2836: Add support for DT interrupt polarity")
changed the way that the BCM2836/7 local interrupts are mapped; instead
of being pre-mapped they are now mapped on-demand. A side effect of this
change is that the call to irq_of_parse_and_map from armctrl_of_init
creates a new mapping, forming a gap between the IRQs and the FIQs. This
gap breaks the FIQ<->IRQ mapping which up to now has been done by assuming:
1) that the value of FIQ_START is the same as the number of normal IRQs
that will be mapped (still true), and
2) that this value is also the offset between an IRQ and its equivalent
FIQ (which is no longer the case).
Remove both assumptions by measuring the interval between the last IRQ
and the last FIQ, passing it as the parameter to init_FIQ().
Fixes: https://github.com/raspberrypi/linux/issues/2432
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Register for reboot notifications, sending RPI_FIRMWARE_NOTIFY_REBOOT
over the mailbox interface on reception.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Add two new DT properties:
* microchip,eee-enabled - a boolean to enable EEE
* microchip,tx-lpi-timer - time in microseconds to wait before entering
low power state
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
I2C busses can be assigned specific bus numbers using aliases in
Device Tree - string properties where the name is the alias and the
value is the path to the node. The current DT parameter mechanism
does not allow property names to be derived from a parameter value
in any way, so it isn't possible to generate unique or matching
aliases for nodes from an overlay that can generate multiple
instances, e.g. i2c-gpio.
Work around this limitation (at least temporarily) by allowing
the i2c adapter number to be initialised from the "reg" property
if present.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
There is a new test in __irq_startup that the IRQ is activated, which
hasn't been the case for FIQs since they bypass some of the usual setup.
Augment enable_fiq to include a call to irq_activate to avoid the
warning.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Create a semi-static mapping for the USB registers early in the boot
process, before additional kernel threads are started, so all threads
will have the mappings from the start. This avoids the need for
data aborts to lazily update them.
See: https://github.com/raspberrypi/linux/issues/2450
Signed-off-by: Floris Bos <bos@je-eigen-domein.nl>
The VideoCore bootloader passes in Serial number and
Revision number through Device Tree. Make these available to
userspace through /proc/cpuinfo.
Mainline status:
There is a commit in linux-next that standardize passing the serial
number through Device Tree (string: /serial-number):
ARM: 8355/1: arch: Show the serial number from devicetree in cpuinfo
There was an attempt to do the same with the revision number, but it
didn't get in:
[PATCH v2 1/2] arm: devtree: Set system_rev from DT revision
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Uses the debugfs I/F to provide access to the AXI
bus performance monitors.
Requires the new mailbox peripheral access for access
to the VPU performance registers, system bus access
is done using direct register reads.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
raspberrypi_axi_monitor: suppress warning
Suppress the following warning by casting the pointer to and uintptr_t
before to u32:
Signed-off-by: Matteo Croce <mcroce@redhat.com>
IRQ-CPU mapping is round robined on ARM64 to increase
concurrency and allow multiple interrupts to be serviced
at a time. This reduces the need for FIQ.
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
brcmfmac: Disable power management
Disable wireless power saving in the brcmfmac WLAN driver. This is a
temporary measure until the connectivity loss resulting from power
saving is resolved.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
brcmfmac: Use original country code as a fallback
Commit 73345fd212:
brcmfmac: Configure country code using device specific settings
prevents region codes from working on devices that lack a region code
translation table. In the event of an absent table, preserve the old
behaviour of using the provided code as-is.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
brcmfmac: Plug memory leak in brcmf_fill_bss_param
See: https://github.com/raspberrypi/linux/issues/1471
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
brcmfmac: do not use internal roaming engine by default
Some evidence of curing disconnects with this disabled, so make it a default.
Can be overridden with module parameter roamoff=0
See: http://projectable.me/optimize-my-pi-wi-fi/
brcmfmac: Change stop_ap sequence
Patch from Broadcom/Cypress to resolve a customer error
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Revert "brcmfmac: Disable power management"
Shortly after the release of the Pi 3B, a loss of SSH connectivity
over WiFi was traced to the power management handling, so power
management was disabled. And so it has remained ever since.
Enabling power management saves 55mA (~270mW) on a Pi 4B, so is very
much worth the minimal effort of reverting this patch, which was
squashed and rebased many times since then to the commit hash is
meaningless.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
This is a port of Pantelis Antoniou's v3 port that makes use of the
new upstreamed configfs support for binary attributes.
Original commit message:
Add a runtime interface to using configfs for generic device tree overlay
usage. With it its possible to use device tree overlays without having
to use a per-platform overlay manager.
Please see Documentation/devicetree/configfs-overlays.txt for more info.
Changes since v2:
- Removed ifdef CONFIG_OF_OVERLAY (since for now it's required)
- Created a documentation entry
- Slight rewording in Kconfig
Changes since v1:
- of_resolve() -> of_resolve_phandles().
Originally-signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
DT configfs: Fix build errors on other platforms
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
DT configfs: fix build error
There is an error when compiling rpi-4.6.y branch:
CC drivers/of/configfs.o
drivers/of/configfs.c:291:21: error: initialization from incompatible pointer type [-Werror=incompatible-pointer-types]
.default_groups = of_cfs_def_groups,
^
drivers/of/configfs.c:291:21: note: (near initialization for 'of_cfs_subsys.su_group.default_groups.next')
The .default_groups is linked list since commit
1ae1602de0.
This commit uses configfs_add_default_group to fix this problem.
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
configfs: New of_overlay API
of: configfs: Use of_overlay_fdt_apply API call
The published API to the dynamic overlay application mechanism now
takes a Flattened Device Tree blob as input so that it can manage the
lifetime of the unflattened tree. Conveniently, the new API call -
of_overlay_fdt_apply - is virtually a drop-in replacement for
create_overlay, which can now be deleted.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Add a virtual GPIO driver that uses the firmware mailbox interface to
request that the VPU toggles LEDs.
gpio: bcm-virt: Fix the get() method
The get() method does not understand the on-the-wire encoding of the
remote GPIO states, thinking they are simple on/off bits when they are
really pairs of 16-bit counts. Rewrite the get() handler to return the
value last written, which will eventually match the actual GPIO state
if there are no other changes.
See: https://github.com/raspberrypi/linux/issues/4638
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Add a mailbox-driven backlight controller for the Raspberry Pi DSI
touchscreen display. Requires updated GPU firmware to recognise the
mailbox request.
Signed-off-by: Gordon Hollingworth <gordon@raspberrypi.org>
Add Raspberry Pi firmware driver to the dependencies of backlight driver
Otherwise the backlight driver fails to build if the firmware
loading driver is not in the kernel
Signed-off-by: Alex Riesen <alexander.riesen@cetitec.com>
ASoC: Add support for Rpi-DAC
ASoC: Add prompt for ICS43432 codec
Without a prompt string, a config setting can't be included in a
defconfig. Give CONFIG_SND_SOC_ICS43432 a prompt so that Pi soundcards
can use the driver.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Add IQaudIO Sound Card support for Raspberry Pi
Set a limit of 0dB on Digital Volume Control
The main volume control in the PCM512x DAC has a range up to
+24dB. This is dangerously loud and can potentially cause massive
clipping in the output stages. Therefore this sets a sensible
limit of 0dB for this control.
Allow up to 24dB digital gain to be applied when using IQAudIO DAC+
24db_digital_gain DT param can be used to specify that PCM512x
codec "Digital" volume control should not be limited to 0dB gain,
and if specified will allow the full 24dB gain.
Modify IQAudIO DAC+ ASoC driver to set card/dai config from dt
Add the ability to set the card name, dai name and dai stream name, from
dt config.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
IQaudIO: auto-mute for AMP+ and DigiAMP+
IQAudIO amplifier mute via GPIO22. Add dt params for "one-shot" unmute
and auto mute.
Revision 2, auto mute implementing HiassofT suggestion to mute/unmute
using set_bias_level, rather than startup/shutdown....
"By default DAPM waits 5 seconds (pmdown_time) before shutting down
playback streams so a close/stop immediately followed by open/start
doesn't trigger an amp mute+unmute."
Tested on both AMP+ (via DAC+) and DigiAMP+, with both options...
dtoverlay=iqaudio-dacplus,unmute_amp
"one-shot" unmute when kernel module loads.
dtoverlay=iqaudio-dacplus,auto_mute_amp
Unmute amp when ALSA device opened by a client. Mute, with 5 second delay
when ALSA device closed. (Re-opening the device within the 5 second close
window, will cancel mute.)
Revision 4, using gpiod.
Revision 5, clean-up formatting before adding mute code.
- Convert tab plus 4 space formatting to 2x tab
- Remove '// NOT USED' commented code
Revision 6, don't attempt to "one-shot" unmute amp, unless card is
successfully registered.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
ASoC: iqaudio-dac: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: iqaudio-dac: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
Added support for HiFiBerry DAC+
The driver is based on the HiFiBerry DAC driver. However HiFiBerry DAC+ uses
a different codec chip (PCM5122), therefore a new driver is necessary.
Add support for the HiFiBerry DAC+ Pro.
The HiFiBerry DAC+ and DAC+ Pro products both use the existing bcm sound driver with the DAC+ Pro having a special clock device driver representing the two high precision oscillators.
An addition bug fix is included for the PCM512x codec where by the physical size of the sample frame is used in the calculation of the LRCK divisor as it was found to be wrong when using 24-bit depth sample contained in a little endian 4-byte sample frame.
Limit PCM512x "Digital" gain to 0dB by default with HiFiBerry DAC+
24db_digital_gain DT param can be used to specify that PCM512x
codec "Digital" volume control should not be limited to 0dB gain,
and if specified will allow the full 24dB gain.
Add dt param to force HiFiBerry DAC+ Pro into slave mode
"dtoverlay=hifiberry-dacplus,slave"
Add 'slave' param to use HiFiBerry DAC+ Pro in slave mode,
with Pi as master for bit and frame clock.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
Fixed a bug when using 352.8kHz sample rate
Signed-off-by: Daniel Matuschek <daniel@hifiberry.com>
ASoC: pcm512x: revert downstream changes
This partially reverts commit 185ea05465
which was added by https://github.com/raspberrypi/linux/pull/1152
The downstream pcm512x changes caused a regression, it broke normal
use of the 24bit format with the codec, eg when using simple-audio-card.
The actual bug with 24bit playback is the incorrect usage
of physical_width in various drivers in the downstream tree
which causes 24bit data to be transmitted with 32 clock
cycles. So it's not the pcm512x that needs fixing, it's the
soundcard drivers.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplus: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplus: transmit S24_LE with 64 BCLK cycles
Signed-off-by: Matthias Reichl <hias@horus.com>
hifiberry_dacplus: switch to snd_soc_dai_set_bclk_ratio
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplus: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add driver for rpi-proto
Forward port of 3.10.x driver from https://github.com/koalo
We are using a custom board and would like to use rpi 3.18.x
kernel. Patch works fine for our embedded system.
URL to the audio chip:
http://www.mikroe.com/add-on-boards/audio-voice/audio-codec-proto/
Playback tested with devicetree enabled.
Signed-off-by: Waldemar Brodkorb <wbrodkorb@conet.de>
ASoC: rpi-proto: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add Support for JustBoom Audio boards
justboom-dac: Adjust for ALSA API change
As of 4.4, snd_soc_limit_volume now takes a struct snd_soc_card *
rather than a struct snd_soc_codec *.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
ASoC: justboom-dac: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Also remove hw_params as it's no longer needed.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: justboom-dac: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
New AudioInjector.net Pi soundcard with low jitter audio in and out.
Contains the sound/soc/bcm ALSA machine driver and necessary alterations to the Kconfig and Makefile.
Adds the dts overlay and updates the Makefile and README.
Updates the relevant defconfig files to enable building for the Raspberry Pi.
Thanks to Phil Elwell (pelwell) for the review, simple-card concepts and discussion. Thanks to Clive Messer for overlay naming suggestions.
Added support for headphones, microphone and bclk_ratio settings.
This patch adds headphone and microphone capability to the Audio Injector sound card. The patch also sets the bit clock ratio for use in the bcm2835-i2s driver. The bcm2835-i2s can't handle an 8 kHz sample rate when the bit clock is at 12 MHz because its register is only 10 bits wide which can't represent the ch2 offset of 1508. For that reason, the rate constraint is added.
ASoC: audioinjector-pi-soundcard: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
New driver for RRA DigiDAC1 soundcard using WM8741 + WM8804
ASoC: digidac1-soundcard: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add support for Dion Audio LOCO DAC-AMP HAT
Using dedicated machine driver and pcm5102a codec driver.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
ASoC: dionaudio_loco: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Allo Piano DAC boards: Initial 2 channel (stereo) support (#1645)
Add initial 2 channel (stereo) support for Allo Piano DAC (2.0/2.1) boards,
using allo-piano-dac-pcm512x-audio overlay and allo-piano-dac ALSA ASoC
machine driver.
NB. The initial support is 2 channel (stereo) ONLY!
(The Piano DAC 2.1 will only support 2 channel (stereo) left/right output,
pending an update to the upstream pcm512x codec driver, which will have
to be submitted via upstream. With the initial downstream support,
provided by this patch, the Piano DAC 2.1 subwoofer outputs will
not function.)
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Signed-off-by: Clive Messer <clive.messer@digitaldreamtime.co.uk>
Tested-by: Clive Messer <clive.messer@digitaldreamtime.co.uk>
ASoC: allo-piano-dac: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Also remove hw_params and ops as they are no longer needed.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: allo-piano-dac: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add support for Allo Piano DAC 2.1 plus add-on board for Raspberry Pi.
The Piano DAC 2.1 has support for 4 channels with subwoofer.
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Reviewed-by: Vijay Kumar B. <vijaykumar@zilogic.com>
Reviewed-by: Raashid Muhammed <raashidmuhammed@zilogic.com>
Add clock changes and mute gpios (#1938)
Also improve code style and adhere to ALSA coding conventions.
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Reviewed-by: Vijay Kumar B. <vijaykumar@zilogic.com>
Reviewed-by: Raashid Muhammed <raashidmuhammed@zilogic.com>
PianoPlus: Dual Mono & Dual Stereo features added (#2069)
allo-piano-dac-plus: Master volume added + fixes
Master volume added, which controls both DACs volumes.
See: https://github.com/raspberrypi/linux/pull/2149
Also fix initial max volume, default mode value, and unmute.
Signed-off-by: allocom <sparky-dev@allo.com>
ASoC: allo-piano-dac-plus: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Signed-off-by: Matthias Reichl <hias@horus.com>
sound: bcm: Fix memset dereference warning
This warning appears with GCC 6.4.0 from toolchains.bootlin.com:
../sound/soc/bcm/allo-piano-dac-plus.c: In function ‘snd_allo_piano_dac_init’:
../sound/soc/bcm/allo-piano-dac-plus.c:711:30: warning: argument to ‘sizeof’ in ‘memset’ call is the same expression as the destination; did you mean to dereference it? [-Wsizeof-pointer-memaccess]
memset(glb_ptr, 0x00, sizeof(glb_ptr));
^
Suggested-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
ASoC: allo-piano-dac-plus: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add support for Allo Boss DAC add-on board for Raspberry Pi. (#1924)
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Reviewed-by: Deepak <deepak@zilogic.com>
Reviewed-by: BabuSubashChandar <babusubashchandar@zilogic.com>
Add support for new clock rate and mute gpios.
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Reviewed-by: Deepak <deepak@zilogic.com>
Reviewed-by: BabuSubashChandar <babusubashchandar@zilogic.com>
ASoC: allo-boss-dac: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: allo-boss-dac: transmit S24_LE with 64 BCLK cycles
Signed-off-by: Matthias Reichl <hias@horus.com>
allo-boss-dac: switch to snd_soc_dai_set_bclk_ratio
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: allo-boss-dac: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Support for Blokas Labs pisound board
Pisound dynamic overlay (#1760)
Restructuring pisound-overlay.dts, so it can be loaded and unloaded dynamically using dtoverlay.
Print a logline when the kernel module is removed.
pisound improvements:
* Added a writable sysfs object to enable scripts / user space software
to blink MIDI activity LEDs for variable duration.
* Improved hw_param constraints setting.
* Added compatibility with S16_LE sample format.
* Exposed some simple placeholder volume controls, so the card appears
in volumealsa widget.
Add missing SND_PISOUND selects dependency to SND_RAWMIDI
Without it the Pisound module fails to compile.
See https://github.com/raspberrypi/linux/issues/2366
Updates for Pisound module code:
* Merged 'Fix a warning in DEBUG builds' (1c8b82b).
* Updating some strings and copyright information.
* Fix for handling high load of MIDI input and output.
* Use dual rate oversampling ratio for 96kHz instead of single
rate one.
Signed-off-by: Giedrius Trainavicius <giedrius@blokas.io>
Fixing memset call in pisound.c
Signed-off-by: Giedrius Trainavicius <giedrius@blokas.io>
Fix for Pisound's MIDI Input getting blocked for a while in rare cases.
There was a possible race condition which could lead to Input's FIFO queue
to be underflown, causing high amount of processing in the worker thread for
some period of time.
Signed-off-by: Giedrius Trainavicius <giedrius@blokas.io>
Fix for Pisound kernel module in Real Time kernel configuration.
When handler of data_available interrupt is fired, queue_work ends up
getting called and it can block on a spin lock which is not allowed in
interrupt context. The fix was to run the handler from a thread context
instead.
Pisound: Remove spinlock usage around spi_sync
ASoC: pisound: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
ASoC: pisound: fix the parameter for spi_device_match
Signed-off-by: Hui Wang <hui.wang@canonical.com>
ASoC: Add driver for Cirrus Logic Audio Card
Note: due to problems with deferred probing of regulators
the following softdep should be added to a modprobe.d file
softdep arizona-spi pre: arizona-ldo1
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: rpi-cirrus: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
sound: Support for Dion Audio LOCO-V2 DAC-AMP HAT
Signed-off-by: Miquel Blauw <info@dionaudio.nl>
ASoC: dionaudio_loco-v2: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Also remove hw_params and ops as they are no longer needed.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: dionaudio_loco-v2: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add support for Fe-Pi audio sound card. (#1867)
Fe-Pi Audio Sound Card is based on NXP SGTL5000 codec.
Mechanical specification of the board is the same the Raspberry Pi Zero.
3.5mm jacks for Headphone/Mic, Line In, and Line Out.
Signed-off-by: Henry Kupis <fe-pi@cox.net>
ASoC: fe-pi-audio: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add support for the AudioInjector.net Octo sound card
AudioInjector Octo: sample rates, regulators, reset
This patch adds new sample rates to the Audioinjector Octo sound card. The
new supported rates are (in kHz) :
96, 48, 32, 24, 16, 8, 88.2, 44.1, 29.4, 22.05, 14.7
Reference the bcm270x DT regulators in the overlay.
This patch adds a reset GPIO for the AudioInjector.net octo sound card.
Audioinjector octo : Make the playback and capture symmetric
This patch ensures that the sample rate and channel count of the audioinjector
octo sound card are symmetric.
audioinjector-octo: Add continuous clock feature
By user request, add a switch to prevent the clocks being stopped when
the stream is paused, stopped or shutdown. Provide access to the switch
by adding a 'non-stop-clocks' parameter to the audioinjector-addons
overlay.
See: https://github.com/raspberrypi/linux/issues/2409
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
sound: Fixes for audioinjector-octo under 4.19
1. Move the DT alias declaration to the I2C shim in the cases
where the shim is enabled. This works around a problem caused by a
4.19 commit [1] that generates DT/OF uevents for I2C drivers.
2. Fix the diagnostics in an error path of the soundcard driver to
correctly identify the reason for the failure to load.
3. Move the declaration of the clock node in the overlay outside
the I2C node to avoid warnings.
4. Sort the overlay nodes so that dependencies are only to earlier
fragments, in an attempt to get runtime dtoverlay application to
work (it still doesn't...)
See: https://github.com/Audio-Injector/Octo/issues/14
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
[1] af503716ac ("i2c: core: report OF style module alias for devices registered via OF")
ASoC: audioinjector-octo-soundcard: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Driver support for Google voiceHAT soundcard.
ASoC: googlevoicehat-codec: Use correct device when grabbing GPIO
The fixup for the VoiceHAT in 4.18 incorrectly tried to find the
sdmode GPIO pin under the card device, not the codec device.
This failed, and therefore caused the device probe to fail.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
ASoC: googlevoicehat-codec: Reformat for kernel coding standards
Fix all whitespace, indentation, and bracing errors.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
ASoC: googlevoicehat-codec: Make driver function structure const
Make voicehat_component_driver a const structure.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
ASoC: googlevoicehat-codec: Only convert from ms to jiffies once
Minor optimisation and allows to become checkpatch clean.
A msec value is read out of DT or from a define, and convert once to
jiffies, rather than every time that it is used.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Driver and overlay for Allo Katana DAC
Allo Katana DAC: Updated default values
Signed-off-by: Jaikumar <jaikumar@cem-solutions.com>
Added mute stream func
Signed-off-by: Jaikumar <jaikumar@cem-solutions.net>
codecs: Correct Katana minimum volume
Update Katana minimum volume to get the exact 0.5 dB value in each step.
Signed-off-by: Sudeep Kumar <sudeepkumar@cem-solutions.net>
ASoC: Add generic RPI driver for simple soundcards.
The RPI simple sound card driver provides a generic ALSA SOC card driver
supporting a variety of Pi HAT soundcards. The intention is to avoid
the duplication of code for cards that can't be fully supported by
the soc simple/graph cards but are otherwise almost identical.
This initial commit adds support for the ADAU1977 ADC, Google VoiceHat,
HifiBerry AMP, HifiBerry DAC and RPI DAC.
Signed-off-by: Tim Gover <tim.gover@raspberrypi.org>
ASoC: Use correct card name in rpi-simple driver
Use the specific card name from drvdata instead of the snd_rpi_simple
rpi-simple-soundcard: Use nicer driver name "RPi-simple"
Rename the driver from "RPI simple soundcard" to "RPi-simple" so that
the driver name won't be mangled allowing to be used unaltered as the
card conf filename.
ASoC: rpi-simple-soundcard: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
ASoC: Add Kconfig and Makefile for sound/soc/bcm
Signed-off-by: popcornmix <popcornmix@gmail.com>
ASoC: Create a generic Pi Hat WM8804 driver
Reduce the amount of duplicated code by creating a generic driver for
Pi Hat digi cards using the WM8804 codec.
This replaces the
Allo DigiOne, Hifiberry Digi/Pro, JustBoom Digi and IQAudIO Digi
dedicate soundcard drivers with a generic driver.
There are no significant changes to the runtime behavior of the drivers
and end users should not have to change any configuration settings
after upgrading.
Minor changes
* Check the return value of snd_soc_component_update_bits
* Added some pr_debug tracing
* Various checkpatch tidyups
* Updated allodigi-one to use use 128FS at > 96 Khz. This appears to
be an omission in the original driver code so followed the Hifiberry
DAC driver approach.
ASoC: rpi-wm8804-soundcard: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
rpi-wm8804-soundcard: drop PWRDN register writes
Since kernel 4.0 the PWRDN register bits are under DAPM
control from the wm8804 driver.
Drop code that modifies that register to avoid interfering
with DAPM.
Signed-off-by: Matthias Reichl <hias@horus.com>
rpi-wm8804-soundcard: configure wm8804 clocks only on rate change
This should avoid clicks when stopping and immediately afterwards
starting a stream with the same samplerate as before.
Signed-off-by: Matthias Reichl <hias@horus.com>
rpi-wm8804-soundcard: Fixed MCLKDIV for Allo Digione
The Allo Digione board wants a fixed MCLKDIV of 256.
See: https://github.com/raspberrypi/linux/issues/3296
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
ASoC: Add support for AudioSense-Pi add-on soundcard
AudioSense-Pi is a RPi HAT based on a TI's TLV320AIC32x4 stereo codec
This hardware provides multiple audio I/O capabilities to the RPi.
The codec connects to the RPi's SoC through the I2S Bus.
The following devices can be connected through a 3.5mm jack
1. Line-In: Plain old audio in from mobile phones, PCs, etc.,
2. Mic-In: Connect a microphone
3. Line-Out: Connect the output to a speaker
4. Headphones: Connect a Headphone w or w/o microphones
Multiple Inputs:
It supports the following combinations
1. Two stereo Line-Inputs and a microphone
2. One stereo Line-Input and two microphones
3. Two stereo Line-Inputs, a microphone and
one mono line-input (with h/w hack)
4. One stereo Line-Input, two microphones and
one mono line-input (with h/w hack)
Multiple Outputs:
Audio output can be routed to the headphones or
speakers (with additional hardware)
Signed-off-by: b-ak <anur.bhargav@gmail.com>
ASoC: audiosense-pi: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Added driver for the HiFiBerry DAC+ ADC (#2694)
Signed-off-by: Daniel Matuschek <daniel@hifiberry.com>
hifiberry_dacplusadc: switch to snd_soc_dai_set_bclk_ratio
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplusadc: fix DAI link setup
The driver only defines a single DAI link and the code that tries
to setup the second (non-existent) DAI link looks wrong - using dmic
as a CPU/platform driver doesn't make any sense.
The DT overlay doesn't define a dmic property, so the code was never
executed (otherwise it would have resulted in a memory corruption).
So drop the offending code to prevent issues if a dmic property
should be added to the DT overlay.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplusadc: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
Audiophonics I-Sabre 9038Q2M DAC driver
Signed-off-by: Audiophonics <contact@audiophonics.fr>
ASoC: i-sabre-q2m: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Added IQaudIO Pi-Codec board support (#2969)
Add support for the IQaudIO Pi-Codec board.
Signed-off-by: Gordon <gordon@iqaudio.com>
Fixed 48k timing issue
ASoC: iqaudio-codec: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
adds the Hifiberry DAC+ADC PRO version
This adds the driver for the DAC+ADC PRO version of the Hifiberry soundcard with software controlled PCM1863 ADC
Signed-off-by: Joerg Schambacher joerg@i2audio.com
Add Hifiberry DAC+DSP soundcard driver (#3224)
Adds the driver for the Hifiberry DAC+DSP. It supports capture and
playback depending on the DSP firmware.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
Allow simultaneous use of JustBoom DAC and Digi
Signed-off-by: Johannes Krude <johannes@krude.de>
Pisound: MIDI communication fixes for scaled down CPU.
* Increased maximum SPI communication speed to avoid running too slow
when the CPU is scaled down and losing MIDI data.
* Keep track of buffer usage in millibytes for higher precision.
Signed-off-by: Giedrius Trainavičius <giedrius@blokas.io>
sound: Add the HiFiBerry DAC+HD version
This adds the driver for the DAC+HD version supporting HiFiBerry's
PCM179x based DACs. It also adds PLL control for clock generation.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
Fix master mode settings of HiFiBerry DAC+ADC PRO card (#3424)
This patch fixes the board DAI setting when in master-mode.
Wrong setting could have caused random pop noise.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
adds LED OFF feature to HiFiBerry DAC+ADC PRO sound card
This adds a DT overlay parameter 'leds_off' which allows
to switch off the onboard activity LEDs at all times
which has been requested by some users.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
adds LED OFF feature to HiFiBerry DAC+ADC sound card
This adds a DT overlay parameter 'leds_off' which allows
to switch off the onboard activity LEDs at all times
which has been requested by some users.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
adds LED OFF feature to HiFiBerry DAC+/DAC+PRO sound cards
This adds a DT overlay parameter 'leds_off' which allows
to switch off the onboard activity LEDs at all times
which has been requested by some users.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
pisound: Added reading Pisound board hardware revision and exposing it (#3425)
pisound: Added reading Pisound board hardware revision and exposing it in kernel log and sysfs file:
/sys/kernel/pisound/hw_version
Signed-off-by: Giedrius <giedrius@blokas.io>
Added driver for HiFiBerry Amp amplifier add-on board
The driver contains a low-level hardware driver for the TAS5713 and the
drivers for the Raspberry Pi I2S subsystem.
TAS5713: return error if initialisation fails
Existing TAS5713 driver logs errors during initialisation, but does not return
an error code. Therefore even if initialisation fails, the driver will still be
loaded, but won't work. This patch fixes this. I2C communication error will now
reported correctly by a non-zero return code.
HiFiBerry Amp: fix device-tree problems
Some code to load the driver based on device-tree-overlays was missing. This is added by this patch.
According to 5713 pdf doc CLOCK_CTRL is a readonly status register, and it behaves so. Remove useless setting
sound: pcm512x-codec: Adding 352.8kHz samplerate support
sound/soc: only first codec is master in multicodec setup
When using multiple codecs, at most one codec should generate the master
clock. All codecs except the first are therefore configured for slave
mode.
Signed-off-by: Johannes Krude <johannes@krude.de>
ASoC: Fix snd_soc_get_pcm_runtime usage
Commit [1] changed the snd_soc_get_pcm_runtime to take a dai_link
pointer instead of a string. Patch up the downstream drivers to use
the modified API.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
[1] 4468189ff3 ("ASoC: soc-core: find rtd via dai_link pointer at snd_soc_get_pcm_runtime()")
Add support for the AudioInjector.net Isolated sound card
This patch adds support for the Audio Injector Isolated sound card.
Signed-off-by: Matt Flax <flatmax@flatmax.org>
Add support for merus-amp soundcard and ma120x0p codec
Add 96KHz rate support to MA120X0P codec and make enable and mute gpio
pins optional.
Signed-off-by: AMuszkat <ariel.muszkat@gmail.com>
Fixes a problem with clock settings of HiFiBerry DAC+ADC PRO (#3545)
This patch fixes a problem of the re-calculation of
i2s-clock and -parameter settings when only the ADC is activated.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
configs: Enable the AD193x codecs
See: https://github.com/raspberrypi/linux/issues/2850
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Switch to snd_soc_dai_set_bclk_ratio
Replaces obsolete function snd_soc_dai_set_tdm_slot
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
Enhances the DAC+ driver to control the optional headphone amplifier
Probes on the I2C bus for TPA6130A2, if successful, it sets DT-parameter
'status' from 'disabled' to 'okay' using change_sets to enable
the headphone control.
Signed-off-by: Joerg Schambacher joerg@i2audio.com
Update Allo Piano Dac Driver
Add unique names to the individual dac coded drivers
Remove some of the codec controls that are not used.
Signed-off-by: Paul Hermann <paul@picoreplayer.org>
Fixes an onboard clock detection problem of the PRO versions
Increasing the sleep time after clock selection to 3-4ms
allows the correct detection of all combinations of DAC+ Pro
and DAC+ADC Pro sound cards and the various PI revisions.
Signed-off-by: Joerg Schambacher <joerg@hifiberry.com>
ASoC:ma120x0p: Increase maximum sample rate to 192KHz
Change the maximum sample rate for the amplifier to
192KHz as given in the Infineon specification.
Signed-off-by: Joerg Schambacher <joerg@hifiberry.com>
ASoC: ma120x0p: Remove unnecessary const specifier
Clang warns:
sound/soc/codecs/ma120x0p.c:891:14: warning: duplicate 'const' declaration specifier [-Wduplicate-decl-specifier]
static const SOC_VALUE_ENUM_SINGLE_DECL(pwr_mode_ctrl,
^
./include/sound/soc.h:362:2: note: expanded from macro 'SOC_VALUE_ENUM_SINGLE_DECL'
SOC_VALUE_ENUM_DOUBLE_DECL(name, xreg, xshift, xshift, xmask, xtexts, xvalues)
^
./include/sound/soc.h:359:2: note: expanded from macro 'SOC_VALUE_ENUM_DOUBLE_DECL'
const struct soc_enum name = SOC_VALUE_ENUM_DOUBLE(xreg, xshift_l, xshift_r, xmask, \
^
1 warning generated.
SOC_VALUE_ENUM_DOUBLE_DECL already has a const specifier. Remove the duplicate
const to clean up the warning.
Fixes: 42444979e7 ("Add support for all the downstream rpi sound card drivers")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
ASoC: bcm: allo-piano-dac-plus: Remove unnecessary const specifiers
Clang warns:
sound/soc/bcm/allo-piano-dac-plus.c:66:14: warning: duplicate 'const' declaration specifier [-Wduplicate-decl-specifier]
static const SOC_ENUM_SINGLE_DECL(allo_piano_mode_enum,
^
./include/sound/soc.h:355:2: note: expanded from macro 'SOC_ENUM_SINGLE_DECL'
SOC_ENUM_DOUBLE_DECL(name, xreg, xshift, xshift, xtexts)
^
./include/sound/soc.h:352:2: note: expanded from macro 'SOC_ENUM_DOUBLE_DECL'
const struct soc_enum name = SOC_ENUM_DOUBLE(xreg, xshift_l, xshift_r, \
^
sound/soc/bcm/allo-piano-dac-plus.c:75:14: warning: duplicate 'const' declaration specifier [-Wduplicate-decl-specifier]
static const SOC_ENUM_SINGLE_DECL(allo_piano_dual_mode_enum,
^
./include/sound/soc.h:355:2: note: expanded from macro 'SOC_ENUM_SINGLE_DECL'
SOC_ENUM_DOUBLE_DECL(name, xreg, xshift, xshift, xtexts)
^
./include/sound/soc.h:352:2: note: expanded from macro 'SOC_ENUM_DOUBLE_DECL'
const struct soc_enum name = SOC_ENUM_DOUBLE(xreg, xshift_l, xshift_r, \
^
sound/soc/bcm/allo-piano-dac-plus.c:96:14: warning: duplicate 'const' declaration specifier [-Wduplicate-decl-specifier]
static const SOC_ENUM_SINGLE_DECL(allo_piano_enum,
^
./include/sound/soc.h:355:2: note: expanded from macro 'SOC_ENUM_SINGLE_DECL'
SOC_ENUM_DOUBLE_DECL(name, xreg, xshift, xshift, xtexts)
^
./include/sound/soc.h:352:2: note: expanded from macro 'SOC_ENUM_DOUBLE_DECL'
const struct soc_enum name = SOC_ENUM_DOUBLE(xreg, xshift_l, xshift_r, \
^
3 warnings generated.
SOC_VALUE_ENUM_DOUBLE_DECL already has a const specifier. Remove the duplicate
const specifiers to clean up the warnings.
Fixes: 42444979e7 ("Add support for all the downstream rpi sound card drivers")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
rpi-simple-soundcard: Add Dion Audio KIWI streamer
Signed-off-by: Miquel Blauw <miquelblauw@hotmail.com>
rpi-simple-soundcard: adds definitions for the HiFiBerry AMP3 card
Uses Infineon MA120x0 amplifier and supports full sample rate of 192ksps.
Signed-off-by: Joerg Schambacher <joerg@hifiberry.com>
sound: soc: bcm: Added Sound card driver for Dacberry400 Audio card for Raspberry Pi 400
Added Sound card driver for DACberry400 Audio card.
Signed-off-by: Ashish Vara <ashishhvara@gmail.com>
ASoC:ma120x0p: Corrects the volume level display
Fixes the wrongly changed 'limiter volume' display back to -50dB minimum
and sets the correct minimum volume level to -144dB to be aligned with
the controls and display in alsamixer etc.
Signed-off-by: Joerg Schambacher <joerg@hifiberry.com>
ASoC: bcm: Fix Rpi-PROTO and audioinjector.net Pi
As of kernel 5.19 the WM8731 driver has separate I2C and SPI support
modules. Change the Kconfig definitions for the audioinjector.net Pi
and Rpi-PROTO soundcards to select SND_SOC_WM8731_I2C.
See: https://github.com/raspberrypi/linux/issues/5364
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
ASoC: adau1977: Add correct compatible strings
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The Raspberry Pi firmware manages the power-down and reboot
process. To do this it installs a pm_power_off handler, causing
the gpio-poweroff module to abort the probe function.
This patch introduces a "force" DT property that overrides that
behaviour, and also adds a DT overlay to enable and control it.
Note that running in an active-low configuration (DT parameter
"active_low") requires a custom dt-blob.bin and probably won't
allow a reboot without switching off, so an external inversion
of the trigger signal may be preferable.
Provide a __copy_from_user that uses memcpy. On BCM2708, use
optimised memcpy/memmove/memcmp/memset implementations.
arch/arm: Add mmiocpy/set aliases for memcpy/set
See: https://github.com/raspberrypi/linux/issues/1082
copy_from_user: CPU_SW_DOMAIN_PAN compatibility
The downstream copy_from_user acceleration must also play nice with
CONFIG_CPU_SW_DOMAIN_PAN.
See: https://github.com/raspberrypi/linux/issues/1381
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Fix copy_from_user if BCM2835_FAST_MEMCPY=n
The change which introduced CONFIG_BCM2835_FAST_MEMCPY unconditionally
changed the behaviour of arm_copy_from_user. The page pinning code
is not safe on ARMv7 if LPAE & high memory is enabled and causes
crashes which look like PTE corruption.
Make __copy_from_user_memcpy conditional on CONFIG_2835_FAST_MEMCPY=y
which is really an ARMv6 / Pi1 optimization and not necessary on newer
ARM processors.
arm: fix mmap unlocks in uaccess_with_memcpy.c
This is a regression that was added with the commit 192a4e923e as of rpi-5.8.y, since that is when the move to the mmap locking API was introduced - d8ed45c5dc
The issue is that when the patch to improve performance for the __copy_to_user and __copy_from_user functions were added for the Raspberry Pi, some of the mmaps were incorrectly mapped to write instead of read. This would cause a verity of issues, and in my case, prevent the booting of a squashfs filesystem on rpi-5.8-y and above. An example of the panic you would see from this can be seen at https://pastebin.com/raw/jBz5xCzL
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Christopher Blake <chrisrblake93@gmail.com>
arch/arm: Add __memset alias to memset_rpi.S
memset_rpi.S is an optimised memset implementation, but doesn't define
__memset (which was just added to memset.S). As a result, building
for the BCM2835 platform causes a link failure.
Add __memset as yet another alias to our common implementation.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
arm: Fix custom rpi __memset32 and __memset64
See: https://github.com/raspberrypi/linux/issues/4798
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
arm: Fix annoying .eh_frame section warnings
Replace the cfi directives with the UNWIND equivalents. This prevents
the .eh_frame section from being created, eliminating the warnings.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The "input" trigger makes the associated GPIO an input. This is to support
the Raspberry Pi PWR LED, which is driven by external hardware in normal use.
N.B. pwr_led is not available on Model A or B boards.
leds-gpio: Implement the brightness_get method
The power LED uses some clever logic that means it is driven
by a voltage measuring circuit when configured as input, otherwise
it is driven by the GPIO output value. This patch wires up the
brightness_get method for leds-gpio so that user-space can monitor
the LED value via /sys/class/gpio/led1/brightness. Using the input
trigger this returns an indication of the system power health,
otherwise it is just whatever value the trigger has written most
recently.
See: https://github.com/raspberrypi/linux/issues/1064
Support booting without Device Tree.
Turn on USB power.
Load driver early because of lacking support for deferred probing
in many drivers.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
firmware: bcm2835: Don't turn on USB power
The raspberrypi-power driver is now used to turn on USB power.
This partly reverts commit:
firmware: bcm2835: Support ARCH_BCM270x
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Add module for accessing the mailbox property channel through
/dev/vcio. Was previously in bcm2708-vcio.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
char: vcio: Add compat ioctl handling
There was no compat ioctl handler, so 32 bit userspace on a
64 bit kernel failed as IOCTL_MBOX_PROPERTY used the size
of char*.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
char: vcio: Fail probe if rpi_firmware is not found.
Device Tree is now the only supported config mechanism, therefore
uncomment the block of code that fails the probe if the
firmware node can't be found.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
drivers: char: vcio: Use common compat header
The definition of compat_ptr is now common for most platforms, but
requires the inclusion of <linux/compat.h>.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
char: vcio: Rewrite as a firmware node child
The old vcio driver is a simple character device that manually locates
the firmware driver. Initialising it before the firmware driver causes
a failure, and no retries are attempted.
Rewrite vcio as a platform driver that depends on a DT node for its
instantiation and the location of the firmware driver, making use of
the miscdevice framework to reduce the code size.
N.B. Using miscdevice changes the udev SUBSYSTEM string, so a change
to the companion udev rule is required in order to continue to set
the correct device permissions, e.g.:
KERNEL="vcio", GROUP="video", MODE="0660"
See: https://github.com/raspberrypi/linux/issues/4620
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
i2c-bcm2708: fixed baudrate
Fixed issue where the wrong CDIV value was set for baudrates below 3815 Hz (for 250MHz bus clock).
In that case the computed CDIV value was more than 0xffff. However the CDIV register width is only 16 bits.
This resulted in incorrect setting of CDIV and higher baudrate than intended.
Example: 3500Hz -> CDIV=0x11704 -> CDIV(16bit)=0x1704 -> 42430Hz
After correction: 3500Hz -> CDIV=0x11704 -> CDIV(16bit)=0xffff -> 3815Hz
The correct baudrate is shown in the log after the cdiv > 0xffff correction.
Perform I2C combined transactions when possible
Perform I2C combined transactions whenever possible, within the
restrictions of the Broadcomm Serial Controller.
Disable DONE interrupt during TA poll
Prevent interrupt from being triggered if poll is missed and transfer
starts and finishes.
i2c: Make combined transactions optional and disabled by default
i2c: bcm2708: add device tree support
Add DT support to driver and add to .dtsi file.
Setup pins in .dts file.
i2c is disabled by default.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
bcm2708: don't register i2c controllers when using DT
The devices for the i2c controllers are in the Device Tree.
Only register devices when not using DT.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
I2C: Only register the I2C device for the current board revision
i2c_bcm2708: Fix clock reference counting
Fix grabbing lock from atomic context in i2c driver
2 main changes:
- check for timeouts in the bcm2708_bsc_setup function as indicated by this comment:
/* poll for transfer start bit (should only take 1-20 polls) */
This implies that the setup function can now fail so account for this everywhere it's called
- Removed the clk_get_rate call from inside the setup function as it locks a mutex and that's not ok since we call it from under a spin lock.
i2c-bcm2708: When using DT, leave the GPIO setup to pinctrl
i2c-bcm2708: Increase timeouts to allow larger transfers
Use the timeout value provided by the I2C_TIMEOUT ioctl when waiting
for completion. The default timeout is 1 second.
See: https://github.com/raspberrypi/linux/issues/260
i2c-bcm2708/BCM270X_DT: Add support for I2C2
The third I2C bus (I2C2) is normally reserved for HDMI use. Careless
use of this bus can break an attached display - use with caution.
It is recommended to disable accesses by VideoCore by setting
hdmi_ignore_edid=1 or hdmi_edid_file=1 in config.txt.
The interface is disabled by default - enable using the
i2c2_iknowwhatimdoing DT parameter.
bcm2708-spi: Don't use static pin configuration with DT
Also remove superfluous error checking - the SPI framework ensures the
validity of the chip_select value.
i2c-bcm2708: Remove non-DT support
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Set the BSC_CLKT clock streching timeout to 35ms as per SMBus specs.
Fixes i2c_bcm2708: Write to FIFO correctly - v2 (#1574)
* i2c: fix i2c_bcm2708: Clear FIFO before sending data
Make sure FIFO gets cleared before trying to send
data in case of a repeated start (COMBINED=Y).
* i2c: fix i2c_bcm2708: Only write to FIFO when not full
Check if FIFO can accept data before writing.
To avoid a peripheral read on the last iteration of a loop,
both bcm2708_bsc_fifo_fill and ~drain are changed as well.
Signed-off-by: Luke Wren <wren6991@gmail.com>
MISC: bcm2835: smi: use clock manager and fix reload issues
Use clock manager instead of self-made clockmanager.
Also fix some error paths that showd up during development
(especially missing release of dma resources on rmmod)
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
bcm2835_smi: re-add dereference to fix DMA transfers
bcm2835_smi_dev: Fix handling of word-odd lengths
The read and write functions did not use the correct pointer offset
when dealing with an odd number of bytes after a DMA transfer. Also,
only handle the remaining odd bytes if the DMA transfer completed
successfully.
Submitted-by: @madimario (GitHub)
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
misc: bcm2835_smi: Use proper enum types for dma_{,un}map_single()
Clang warns:
drivers/misc/bcm2835_smi.c:692:4: warning: implicit conversion from enumeration type 'enum dma_transfer_direction' to different enumeration type 'enum dma_data_direction' [-Wenum-conversion]
DMA_MEM_TO_DEV);
^~~~~~~~~~~~~~~
./include/linux/dma-mapping.h:406:66: note: expanded from macro 'dma_map_single'
#define dma_map_single(d, a, s, r) dma_map_single_attrs(d, a, s, r, 0)
~~~~~~~~~~~~~~~~~~~~ ^
drivers/misc/bcm2835_smi.c:705:35: warning: implicit conversion from enumeration type 'enum dma_transfer_direction' to different enumeration type 'enum dma_data_direction' [-Wenum-conversion]
(inst->dev, phy_addr, n_bytes, DMA_MEM_TO_DEV);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~
./include/linux/dma-mapping.h:407:70: note: expanded from macro 'dma_unmap_single'
#define dma_unmap_single(d, a, s, r) dma_unmap_single_attrs(d, a, s, r, 0)
~~~~~~~~~~~~~~~~~~~~~~ ^
drivers/misc/bcm2835_smi.c:751:12: warning: implicit conversion from enumeration type 'enum dma_transfer_direction' to different enumeration type 'enum dma_data_direction' [-Wenum-conversion]
DMA_DEV_TO_MEM);
^~~~~~~~~~~~~~~
./include/linux/dma-mapping.h:406:66: note: expanded from macro 'dma_map_single'
#define dma_map_single(d, a, s, r) dma_map_single_attrs(d, a, s, r, 0)
~~~~~~~~~~~~~~~~~~~~ ^
drivers/misc/bcm2835_smi.c:761:50: warning: implicit conversion from enumeration type 'enum dma_transfer_direction' to different enumeration type 'enum dma_data_direction' [-Wenum-conversion]
dma_unmap_single(inst->dev, phy_addr, n_bytes, DMA_DEV_TO_MEM);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~
./include/linux/dma-mapping.h:407:70: note: expanded from macro 'dma_unmap_single'
#define dma_unmap_single(d, a, s, r) dma_unmap_single_attrs(d, a, s, r, 0)
~~~~~~~~~~~~~~~~~~~~~~ ^
4 warnings generated.
Use the proper enumerated type to clear up the warning. There is not
actually a bug here because the enumerated types have the same integer
value:
DMA_MEM_TO_DEV = DMA_TO_DEVICE = 1
DMA_DEV_TO_MEM = DMA_FROM_DEVICE = 2
Fixes: 93254d0f7b ("Add SMI driver")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: popcornmix <popcornmix@gmail.com>
BCM270x: Move vc_mem
Make the vc_mem module available for ARCH_BCM2835 by moving it.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
char: vc_mem: Fix up compat ioctls for 64bit kernel
compat_ioctl wasn't defined, so 32bit user/64bit kernel
always failed.
VC_MEM_IOC_MEM_PHYS_ADDR was defined with parameter size
unsigned long, so the ioctl cmd changes between sizes.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
char: vc_mem: Fix all coding style issues.
Cleans up all checkpatch errors in vc_mem.c and vc_mem.h
No functional change to the code.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
char: vc_mem: Delete dead code
There are no error exists once device_create has succeeded, and
therefore no need to call device_destroy from vc_mem_init.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
BCM2835 has two SD card interfaces. This driver uses the other one.
bcm2835-sdhost: Error handling fix, and code clarification
bcm2835-sdhost: Adding overclocking option
Allow a different clock speed to be substitued for a requested 50MHz.
This option is exposed using the "overclock_50" DT parameter.
Note that the sdhost interface is restricted to integer divisions of
core_freq, and the highest sensible option for a core_freq of 250MHz
is 84 (250/3 = 83.3MHz), the next being 125 (250/2) which is much too
high.
Use at your own risk.
bcm2835-sdhost: Round up the overclock, so 62 works for 62.5Mhz
Also only warn once for each overclock setting.
bcm2835-sdhost: Improve error handling and recovery
1) Expose the hw_reset method to the MMC framework, removing many
internal calls by the driver.
2) Reduce overclock setting on error.
3) Increase timeout to cope with high capacity cards.
4) Add properties and parameters to control pio_limit and debug.
5) Reduce messages at probe time.
bcm2835-sdhost: Further improve overclock back-off
bcm2835-sdhost: Clear HBLC for PIO mode
Also update pio_limit default in overlay README.
bcm2835-sdhost: Add the ERASE capability
See: https://github.com/raspberrypi/linux/issues/1076
bcm2835-sdhost: Ignore CRC7 for MMC CMD1
It seems that the sdhost interface returns CRC7 errors for CMD1,
which is the MMC-specific SEND_OP_COND. Returning these errors to
the MMC layer causes a downward spiral, but ignoring them seems
to be harmless.
bcm2835-mmc/sdhost: Remove ARCH_BCM2835 differences
The bcm2835-mmc driver (and -sdhost driver that copied from it)
contains code to handle SDIO interrupts in a threaded interrupt
handler rather than waking the MMC framework thread. The change
follows a patch from Russell King that adds the facility as the
preferred way of working.
However, the new code path is only present in ARCH_BCM2835
builds, which I have taken to be a way of testing the waters
rather than making the change across the board; I can't see
any technical reason why it wouldn't be enabled for MACH_BCM270X
builds. So this patch standardises on the ARCH_BCM2835 code,
removing the old code paths.
bcm2835-sdhost: Don't log timeout errors unless debug=1
The MMC card-discovery process generates timeouts. This is
expected behaviour, so reporting it to the user serves no purpose.
Suppress the reporting of timeout errors unless the debug flag
is on.
bcm2835-sdhost: Add workaround for odd behaviour on some cards
For reasons not understood, the sdhost driver fails when reading
sectors very near the end of some SD cards. The problem could
be related to the similar issue that reading the final sector
of any card as part of a multiple read never completes, and the
workaround is an extension of the mechanism introduced to solve
that problem which ensures those sectors are always read singly.
bcm2835-sdhost: Major revision
This is a significant revision of the bcm2835-sdhost driver. It
improves on the original in a number of ways:
1) Through the use of CMD23 for reads it appears to avoid problems
reading some sectors on certain high speed cards.
2) Better atomicity to prevent crashes.
3) Higher performance.
4) Activity logging included, for easier diagnosis in the event
of a problem.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Restore ATOMIC flag to PIO sg mapping
Allocation problems have been seen in a wireless driver, and
this is the only change which might have been responsible.
SQUASH: bcm2835-sdhost: Only claim one DMA channel
With both MMC controllers enabled there are few DMA channels left. The
bcm2835-sdhost driver only uses DMA in one direction at a time, so it
doesn't need to claim two channels.
See: https://github.com/raspberrypi/linux/issues/1327
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Workaround for "slow" sectors
Some cards have been seen to cause timeouts after certain sectors are
read. This workaround enforces a minimum delay between the stop after
reading one of those sectors and a subsequent data command.
Using CMD23 (SET_BLOCK_COUNT) avoids this problem, so good cards will
not be penalised by this workaround.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Firmware manages the clock divisor
The bcm2835-sdhost driver hands control of the CDIV clock divisor
register to matching firmware, allowing it to adjust to a changing
core clock. This removes the need to use the performance governor or
to enable io_is_busy on the on-demand governor in order to get the
best SD performance.
N.B. As SD clocks must be an integer divisor of the core clock, it is
possible that the SD clock for "turbo" mode can be different (even
lower) than "normal" mode.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Reset the clock in task context
Since reprogramming the clock can now involve a round-trip to the
firmware it must not be done at atomic context, and a tasklet
is not a task.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Don't exit cmd wait loop on error
The FAIL flag can be set in the CMD register before command processing
is complete, leading to spurious "failed to complete" errors. This has
the effect of promoting harmless CRC7 errors during CMD1 processing
into errors that can delay and even prevent booting.
Also:
1) Convert the last KERN_ERROR message in the register dumping to
KERN_INFO.
2) Remove an unnecessary reset call from bcm2835_sdhost_add_host.
See: https://github.com/raspberrypi/linux/pull/1492
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: mmc_card_blockaddr fix
Get the definition of mmc_card_blockaddr from drivers/mmc/core/card.h.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: New timer API
mmc: bcm2835-sdhost: Support underclocking
Support underclocking of the SD bus in two ways:
1. using the max-frequency DT property (which currently has no DT
parameter), and
2. using the exiting sd_overclock parameter.
The two methods differ slightly - in the former the MMC subsystem is
aware of the underclocking, while in the latter it isn't - but the
end results should be the same.
See: https://github.com/raspberrypi/linux/issues/2350
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mmc: bcm2835-sdhost: Add include
highmem.h (needed for kmap_atomic) is pulled in by one of the other
include files, but only with some CONFIG settings. Make the inclusion
explicit to cater for cases where the CONFIG setting is absent.
See: https://github.com/raspberrypi/linux/issues/2366
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mmc/bcm2835-sdhost: Recover from MMC_SEND_EXT_CSD
If the user issues an "mmc extcsd read", the SD controller receives
what it thinks is a SEND_IF_COND command with an unexpected data block.
The resulting operations leave the FSM stuck in READWAIT, a state which
persists until the MMC framework resets the controller, by which point
the root filesystem is likely to have been unmounted.
A less heavyweight solution is to detect the condition and nudge the
FSM by asserting the (self-clearing) FORCE_DATA_MODE bit.
N.B. This workaround was essentially discovered by accident and without
a full understanding the inner workings of the controller, so it is
fortunate that the "fix" only modifies error paths.
See: https://github.com/raspberrypi/linux/issues/2728
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mmc: bcm2835-sdhost: Fix warnings on arm64
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Allow for sg entries that cross pages
The dma_complete handling code calculates a virtual address for a page
then adds an offset, but if the offset is more than a page and HIGHMEM
is in use then the summed address could be in an unmapped (or just
incorrect) page.
The upstream SDHOST driver allows for this possibility - copy the code
that does so.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Fix DMA channel leak on error/remove
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mmc: bcm2835-sdhost: Support 64-bit physical addresses
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Replace obsolete struct timeval
struct timeval has been retired due to the impending linux 32-bit tv_sec
rollover (only 18 years to go) - timespec64 is the obvious replacement.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
mmc: sdhost: Pass DT pointer to rpi_firmware_get
Using the rpi_firmware API as intended allows proper reference counting
of the firmware device and means we can remove a downstream patch to
the firmware driver.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
mmc: Disable CMD23 transfers on all cards
Pending wire-level investigation of these types of transfers
and associated errors on bcm2835-mmc, disable for now. Fallback of
CMD18/CMD25 transfers will be used automatically by the MMC layer.
Reported/Tested-by: Gellert Weisz <gellert@raspberrypi.org>
mmc: bcm2835-mmc: enable DT support for all architectures
Both ARCH_BCM2835 and ARCH_BCM270x are built with OF now.
Enable Device Tree support for all architectures.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
mmc: bcm2835-mmc: fix probe error handling
Probe error handling is broken in several places.
Simplify error handling by using device managed functions.
Replace pr_{err,info} with dev_{err,info}.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2835-mmc: Add locks when accessing sdhost registers
bcm2835-mmc: Add range of debug options for slowing things down
bcm2835-mmc: Add option to disable some delays
bcm2835-mmc: Add option to disable MMC_QUIRK_BLK_NO_CMD23
bcm2835-mmc: Default to disabling MMC_QUIRK_BLK_NO_CMD23
bcm2835-mmc: Adding overclocking option
Allow a different clock speed to be substitued for a requested 50MHz.
This option is exposed using the "overclock_50" DT parameter.
Note that the mmc interface is restricted to EVEN integer divisions of
250MHz, and the highest sensible option is 63 (250/4 = 62.5), the
next being 125 (250/2) which is much too high.
Use at your own risk.
bcm2835-mmc: Round up the overclock, so 62 works for 62.5Mhz
Also only warn once for each overclock setting.
mmc: bcm2835-mmc: Make available on ARCH_BCM2835
Make the bcm2835-mmc driver available for use on ARCH_BCM2835.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270x_DT: add bcm2835-mmc entry
Add Device Tree entry for bcm2835-mmc.
In non-DT mode, don't add the device in the board file.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2835-mmc: Don't overwrite MMC capabilities from DT
bcm2835-mmc: Don't override bus width capabilities from devicetree
Take out the force setting of the MMC_CAP_4_BIT_DATA host capability
so that the result read from devicetree via mmc_of_parse() is
preserved.
bcm2835-mmc: Only claim one DMA channel
With both MMC controllers enabled there are few DMA channels left. The
bcm2835-mmc driver only uses DMA in one direction at a time, so it
doesn't need to claim two channels.
See: https://github.com/raspberrypi/linux/issues/1327
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-mmc: New timer API
mmc: bcm2835-mmc: Support underclocking
Support underclocking of the SD bus using the max-frequency DT property
(which currently has no DT parameter). The sd_overclock parameter
already provides another way to achieve the same thing which should be
equivalent in end result, but it is a bug not to support max-frequency
as well.
See: https://github.com/raspberrypi/linux/issues/2350
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mmc/bcm2835: Recover from MMC_SEND_EXT_CSD
If the user issues an "mmc extcsd read", the SD controller receives
what it thinks is a SEND_IF_COND command with an unexpected data block.
The resulting operations leave the FSM stuck in READWAIT, a state which
persists until the MMC framework resets the controller, by which point
the root filesystem is likely to have been unmounted.
A less heavyweight solution is to detect the condition and nudge the
FSM by asserting the (self-clearing) FORCE_DATA_MODE bit.
N.B. This workaround was essentially discovered by accident and without
a full understanding the inner workings of the controller, so it is
fortunate that the "fix" only modifies error paths.
See: https://github.com/raspberrypi/linux/issues/2728
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-mmc: Fix DMA channel leak
The BCM2835 MMC host driver requests a DMA channel on probe but neglects
to release the channel in the probe error path and on driver unbind.
I'm seeing this happen on every boot of the Compute Module 3: On first
driver probe, DMA channel 2 is allocated and then leaked with a "could
not get clk, deferring probe" message. On second driver probe, channel 4
is allocated.
Fix it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
bcm2835-mmc: Fix struct mmc_host leak on probe
The BCM2835 MMC host driver requests the bus address of the host's
register map on probe. If that fails, the driver leaks the struct
mmc_host allocated earlier.
Fix it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
bcm2835-mmc: Fix duplicate free_irq() on remove
The BCM2835 MMC host driver requests its interrupt as a device-managed
resource, so the interrupt is automatically freed after the driver is
unbound.
However on driver unbind, bcm2835_mmc_remove() frees the interrupt
explicitly to avoid invocation of the interrupt handler after driver
structures have been torn down.
The interrupt is thus freed twice, leading to a WARN splat in
__free_irq(). Fix by not requesting the interrupt as a device-managed
resource.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
bcm2835-mmc: Handle mmc_add_host() errors
The BCM2835 MMC host driver calls mmc_add_host() but doesn't check its
return value. Errors occurring in that function are therefore not
handled. Fix it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
bcm2835-mmc: Deduplicate reset of driver data on remove
The BCM2835 MMC host driver sets the device's driver data pointer to
NULL on ->remove() even though the driver core subsequently does the
same in __device_release_driver(). Drop the duplicate assignment.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
bcm2835_mmc: Remove vestigial threaded IRQ
With SDIO processing now managed by the MMC framework with a
workqueue, the bcm2835_mmc driver no longer needs a threaded
IRQ.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Add missing dma_unmap_sg calls to free relevant swiotlb bounce buffers.
This prevents DMA leaks.
Signed-off-by: Yaroslav Rosomakho <yaroslavros@gmail.com>
Limit max_req_size under arm64 (or any other platform that uses swiotlb) to prevent potential buffer overflow due to bouncing.
Signed-off-by: Yaroslav Rosomakho <yaroslavros@gmail.com>
mmc: sdhci: Silence MMC warnings
When the MMC isn't plugged in, the driver will spam the console which is
pretty annoying when using NFS.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
mmc: sdhci-iproc: Fix vmmc regulators on iProc
The Linux support for controlling card power via regulators appears to
be contentious. I would argue that the default behaviour is contrary to
the SDHCI spec - turning off the power writes a reserved value to the
SD Bus Voltage Select field of the Power Control Register, which
seems to kill the Arasan/iProc controller - but fortunately there is a
hook in sdhci_ops to override the behaviour. Borrow the implementation
from sdhci_arasan_set_power.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-mmc: uninitialized_var is no more
Revert "mmc: sdhci-iproc: Fix vmmc regulators on iProc"
This reverts commit aed19399a0.
Commit 6c92ae1e45 ("mmc: sdhci: Introduce sdhci_set_power_and_bus_voltage()")
introduced a generic helper that does the same thing so use that instead in
the following commit.
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
mmc: sdhci-iproc: Fix vmmc regulators (pre-bcm2711)
The Linux support for controlling card power via regulators appears to
be contentious. I would argue that the default behaviour is contrary to
the SDHCI spec - turning off the power writes a reserved value to the
SD Bus Voltage Select field of the Power Control Register, which
seems to kill the Arasan/iProc controller - but fortunately there is a
hook in sdhci_ops to override the behaviour.
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Add support for DMA controller of BCM2708 as used in the Raspberry Pi.
Currently it only supports cyclic DMA.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
dmaengine: expand functionality by supporting scatter/gather transfers sdhci-bcm2708 and dma.c: fix for LITE channels
DMA: fix cyclic LITE length overflow bug
dmaengine: bcm2708: Remove chancnt affectations
Mirror bcm2835-dma.c commit 9eba5536a7:
chancnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: overwrite dreq only if it is not set
dreq is set when the DMA channel is fetched from Device Tree.
slave_id is set using dmaengine_slave_config().
Only overwrite dreq with slave_id if it is not set.
dreq/slave_id in the cyclic DMA case is not touched, because I don't
have hardware to test with.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: do device registration in the board file
Don't register the device in the driver. Do it in the board file.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: don't restrict DT support to ARCH_BCM2835
Both ARCH_BCM2835 and ARCH_BCM270x are built with OF now.
Add Device Tree support to the non ARCH_BCM2835 case.
Use the same driver name regardless of architecture.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270x_DT: add bcm2835-dma entry
Add Device Tree entry for bcm2835-dma.
The entry doesn't contain any resources since they are handled
by the arch/arm/mach-bcm270x/dma.c driver.
In non-DT mode, don't add the device in the board file.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2708-dmaengine: Add debug options
BCM270x: Add memory and irq resources to dmaengine device and DT
Prepare for merging of the legacy DMA API arch driver dma.c
with bcm2708-dmaengine by adding memory and irq resources both
to platform file device and Device Tree node.
Don't use BCM_DMAMAN_DRIVER_NAME so we don't have to include mach/dma.h
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: Merge with arch dma.c driver and disable dma.c
Merge the legacy DMA API driver with bcm2708-dmaengine.
This is done so we can use bcm2708_fb on ARCH_BCM2835 (mailbox
driver is also needed).
Changes to the dma.c code:
- Use BIT() macro.
- Cutdown some comments to one line.
- Add mutex to vc_dmaman and use this, since the dev lock is locked
during probing of the engine part.
- Add global g_dmaman variable since drvdata is used by the engine part.
- Restructure for readability:
vc_dmaman_chan_alloc()
vc_dmaman_chan_free()
bcm_dma_chan_free()
- Restructure bcm_dma_chan_alloc() to simplify error handling.
- Use device irq resources instead of hardcoded bcm_dma_irqs table.
- Remove dev_dmaman_register() and code it directly.
- Remove dev_dmaman_deregister() and code it directly.
- Simplify bcm_dmaman_probe() using devm_* functions.
- Get dmachans from DT if available.
- Keep 'dma.dmachans' module argument name for backwards compatibility.
Make it available on ARCH_BCM2835 as well.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: set residue_granularity field
bcm2708-dmaengine supports residue reporting at burst level
but didn't report this via the residue_granularity field.
Without this field set properly we get playback issues with I2S cards.
dmaengine: bcm2708-dmaengine: Fix memory leak when stopping a running transfer
bcm2708-dmaengine: Use more DMA channels (but not 12)
1) Only the bcm2708_fb drivers uses the legacy DMA API, and
it requires a BULK-capable channel, so all other types
(FAST, NORMAL and LITE) can be made available to the regular
DMA API.
2) DMA channels 11-14 share an interrupt. The driver can't
handle this, so don't use channels 12-14 (12 was used, probably
because it appears to have an interrupt, but in reality that
interrupt is for activity on ANY channel). This may explain
a lockup encountered when running out of DMA channels.
The combined effect of this patch is to leave 7 DMA channels
available + channel 0 for bcm2708_fb via the legacy API.
See: https://github.com/raspberrypi/linux/issues/1110https://github.com/raspberrypi/linux/issues/1108
dmaengine: bcm2708: Make legacy API available for bcm2835-dma
bcm2708_fb uses the legacy DMA API, so in order to start using
bcm2835-dma, bcm2835-dma has to support the legacy API. Make this
possible by exporting bcm_dmaman_probe() and bcm_dmaman_remove().
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: Change DT compatible string
Both bcm2835-dma and bcm2708-dmaengine have the same compatible string.
So change compatible to "brcm,bcm2708-dma".
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: Remove driver but keep legacy API
Dropping non-DT support means we don't need this driver,
but we still need the legacy DMA API.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2708-dmaengine - Fix arm64 portability/build issues
dma-bcm2708: Fix module compilation of CONFIG_DMA_BCM2708
bcm2708-dmaengine.c defines functions like bcm_dma_start which are
defined as well in dma-bcm2708.h as inline versions when
CONFIG_DMA_BCM2708 is not defined. This works fine when
CONFIG_DMA_BCM2708 is built in, but when it is selected as module build
fails with redefinition errors because in the build system when
CONFIG_DMA_BCM2708 is selected as module, the macro becomes
CONFIG_DMA_BCM2708_MODULE.
This patch makes the header use CONFIG_DMA_BCM2708_MODULE too when
available.
Fixes https://github.com/raspberrypi/linux/issues/2056
Signed-off-by: Andrei Gherzan <andrei@gherzan.com>
bcm2708-dmaengine: Use platform_get_irq
The platform driver framework no longer creates IRQ resources for
platform devices because they are expected to use platform_get_irq.
This causes the bcm2808_fb acceleration to fail.
Fix the problem by calling platform_get_irq as intended.
See: https://github.com/raspberrypi/linux/issues/5131
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Based on the patch authored by Ali Gholami Rudi at
https://lkml.org/lkml/2009/7/13/153
Provide an ioctl for userspace applications, but only if this operation
is hardware accelerated (otherwide it does not make any sense).
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
bcm2708_fb: Add ioctl for reading gpu memory through dma
video: bcm2708_fb: Add compat_ioctl support.
When using a 64 bit kernel with 32 bit userspace we need
compat ioctl handling for FBIODMACOPY as one of the
parameters is a pointer.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: popcornmix <popcornmix@gmail.com>
bcm2708_fb : Implement blanking support using the mailbox property interface
bcm2708_fb: Add pan and vsync controls
bcm2708_fb: DMA acceleration for fb_copyarea
Based on http://www.raspberrypi.org/phpBB3/viewtopic.php?p=62425#p62425
Also used Simon's dmaer_master module as a reference for tweaking DMA
settings for better performance.
For now busylooping only. IRQ support might be added later.
With non-overclocked Raspberry Pi, the performance is ~360 MB/s
for simple copy or ~260 MB/s for two-pass copy (used when dragging
windows to the right).
In the case of using DMA channel 0, the performance improves
to ~440 MB/s.
For comparison, VFP optimized CPU copy can only do ~114 MB/s in
the same conditions (hindered by reading uncached source buffer).
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
bcm2708_fb: report number of dma copies
Add a counter (exported via debugfs) reporting the
number of dma copies that the framebuffer driver
has done, in order to help evaluate different
optimization strategies.
Signed-off-by: Luke Diamand <luked@broadcom.com>
bcm2708_fb: use IRQ for DMA copies
The copyarea ioctl() uses DMA to speed things along. This
was busy-waiting for completion. This change supports using
an interrupt instead for larger transfers. For small
transfers, busy-waiting is still likely to be faster.
Signed-off-by: Luke Diamand <luke@diamand.org>
bcm2708: Make ioctl logging quieter
video: fbdev: bcm2708_fb: Don't panic on error
No need to panic the kernel if the video driver fails.
Just print a message and return an error.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
fbdev: bcm2708_fb: Add ARCH_BCM2835 support
Add Device Tree support.
Pass the device to dma_alloc_coherent() in order to get the
correct bus address on ARCH_BCM2835.
Use the new DMA legacy API header file.
Including <mach/platform.h> is not necessary.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270x_DT: Add bcm2708-fb device
Add bcm2708-fb to Device Tree and don't add the
platform device when booting in DT mode.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Cleanup of bcm2708_fb file to kernel coding standards
Some minor change to function - remove a use of
in_atomic, plus replacing various debug messages
that manually specify the function name with
("%s",.__func__)
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
video: bcm2708_fb: Try allocating on the ARM and passing to VPU
Currently the VPU allocates the contiguous buffer for the
framebuffer.
Try an alternate path first where we use dma_alloc_coherent
and pass the buffer to the VPU. Should the VPU firmware not
support that path, then free the buffer and revert to the
old behaviour of using the VPU allocation.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: popcornmix <popcornmix@gmail.com>
usb: dwc: fix lockdep false positive
Signed-off-by: Kari Suvanto <karis79@gmail.com>
usb: dwc: fix inconsistent lock state
Signed-off-by: Kari Suvanto <karis79@gmail.com>
Add FIQ patch to dwc_otg driver. Enable with dwc_otg.fiq_fix_enable=1. Should give about 10% more ARM performance.
Thanks to Gordon and Costas
Avoid dynamic memory allocation for channel lock in USB driver. Thanks ddv2005.
Add NAK holdoff scheme. Enabled by default, disable with dwc_otg.nak_holdoff_enable=0. Thanks gsh
Make sure we wait for the reset to finish
dwc_otg: fix bug in dwc_otg_hcd.c resulting in silent kernel
memory corruption, escalating to OOPS under high USB load.
dwc_otg: Fix unsafe access of QTD during URB enqueue
In dwc_otg_hcd_urb_enqueue during qtd creation, it was possible that the
transaction could complete almost immediately after the qtd was assigned
to a host channel during URB enqueue, which meant the qtd pointer was no
longer valid having been completed and removed. Usually, this resulted in
an OOPS during URB submission. By predetermining whether transactions
need to be queued or not, this unsafe pointer access is avoided.
This bug was only evident on the Pi model A where a device was attached
that had no periodic endpoints (e.g. USB pendrive or some wlan devices).
dwc_otg: Fix incorrect URB allocation error handling
If the memory allocation for a dwc_otg_urb failed, the kernel would OOPS
because for some reason a member of the *unallocated* struct was set to
zero. Error handling changed to fail correctly.
dwc_otg: fix potential use-after-free case in interrupt handler
If a transaction had previously aborted, certain interrupts are
enabled to track error counts and reset where necessary. On IN
endpoints the host generates an ACK interrupt near-simultaneously
with completion of transfer. In the case where this transfer had
previously had an error, this results in a use-after-free on
the QTD memory space with a 1-byte length being overwritten to
0x00.
dwc_otg: add handling of SPLIT transaction data toggle errors
Previously a data toggle error on packets from a USB1.1 device behind
a TT would result in the Pi locking up as the driver never handled
the associated interrupt. Patch adds basic retry mechanism and
interrupt acknowledgement to cater for either a chance toggle error or
for devices that have a broken initial toggle state (FT8U232/FT232BM).
dwc_otg: implement tasklet for returning URBs to usbcore hcd layer
The dwc_otg driver interrupt handler for transfer completion will spend
a very long time with interrupts disabled when a URB is completed -
this is because usb_hcd_giveback_urb is called from within the handler
which for a USB device driver with complicated processing (e.g. webcam)
will take an exorbitant amount of time to complete. This results in
missed completion interrupts for other USB packets which lead to them
being dropped due to microframe overruns.
This patch splits returning the URB to the usb hcd layer into a
high-priority tasklet. This will have most benefit for isochronous IN
transfers but will also have incidental benefit where multiple periodic
devices are active at once.
dwc_otg: fix NAK holdoff and allow on split transactions only
This corrects a bug where if a single active non-periodic endpoint
had at least one transaction in its qh, on frnum == MAX_FRNUM the qh
would get skipped and never get queued again. This would result in
a silent device until error detection (automatic or otherwise) would
either reset the device or flush and requeue the URBs.
Additionally the NAK holdoff was enabled for all transactions - this
would potentially stall a HS endpoint for 1ms if a previous error state
enabled this interrupt and the next response was a NAK. Fix so that
only split transactions get held off.
dwc_otg: Call usb_hcd_unlink_urb_from_ep with lock held in completion handler
usb_hcd_unlink_urb_from_ep must be called with the HCD lock held. Calling it
asynchronously in the tasklet was not safe (regression in
c4564d4a1a).
This change unlinks it from the endpoint prior to queueing it for handling in
the tasklet, and also adds a check to ensure the urb is OK to be unlinked
before doing so.
NULL pointer dereference kernel oopses had been observed in usb_hcd_giveback_urb
when a USB device was unplugged/replugged during data transfer. This effect
was reproduced using automated USB port power control, hundreds of replug
events were performed during active transfers to confirm that the problem was
eliminated.
USB fix using a FIQ to implement split transactions
This commit adds a FIQ implementaion that schedules
the split transactions using a FIQ so we don't get
held off by the interrupt latency of Linux
dwc_otg: fix device attributes and avoid kernel warnings on boot
dcw_otg: avoid logging function that can cause panics
See: https://github.com/raspberrypi/firmware/issues/21
Thanks to cleverca22 for fix
dwc_otg: mask correct interrupts after transaction error recovery
The dwc_otg driver will unmask certain interrupts on a transaction
that previously halted in the error state in order to reset the
QTD error count. The various fine-grained interrupt handlers do not
consider that other interrupts besides themselves were unmasked.
By disabling the two other interrupts only ever enabled in DMA mode
for this purpose, we can avoid unnecessary function calls in the
IRQ handler. This will also prevent an unneccesary FIQ interrupt
from being generated if the FIQ is enabled.
dwc_otg: fiq: prevent FIQ thrash and incorrect state passing to IRQ
In the case of a transaction to a device that had previously aborted
due to an error, several interrupts are enabled to reset the error
count when a device responds. This has the side-effect of making the
FIQ thrash because the hardware will generate multiple instances of
a NAK on an IN bulk/interrupt endpoint and multiple instances of ACK
on an OUT bulk/interrupt endpoint. Make the FIQ mask and clear the
associated interrupts.
Additionally, on non-split transactions make sure that only unmasked
interrupts are cleared. This caused a hard-to-trigger but serious
race condition when you had the combination of an endpoint awaiting
error recovery and a transaction completed on an endpoint - due to
the sequencing and timing of interrupts generated by the dwc_otg core,
it was possible to confuse the IRQ handler.
Fix function tracing
dwc_otg: whitespace cleanup in dwc_otg_urb_enqueue
dwc_otg: prevent OOPSes during device disconnects
The dwc_otg_urb_enqueue function is thread-unsafe. In particular the
access of urb->hcpriv, usb_hcd_link_urb_to_ep, dwc_otg_urb->qtd and
friends does not occur within a critical section and so if a device
was unplugged during activity there was a high chance that the
usbcore hub_thread would try to disable the endpoint with partially-
formed entries in the URB queue. This would result in BUG() or null
pointer dereferences.
Fix so that access of urb->hcpriv, enqueuing to the hardware and
adding to usbcore endpoint URB lists is contained within a single
critical section.
dwc_otg: prevent BUG() in TT allocation if hub address is > 16
A fixed-size array is used to track TT allocation. This was
previously set to 16 which caused a crash because
dwc_otg_hcd_allocate_port would read past the end of the array.
This was hit if a hub was plugged in which enumerated as addr > 16,
due to previous device resets or unplugs.
Also add #ifdef FIQ_DEBUG around hcd->hub_port_alloc[], which grows
to a large size if 128 hub addresses are supported. This field is
for debug only for tracking which frame an allocate happened in.
dwc_otg: make channel halts with unknown state less damaging
If the IRQ received a channel halt interrupt through the FIQ
with no other bits set, the IRQ would not release the host
channel and never complete the URB.
Add catchall handling to treat as a transaction error and retry.
dwc_otg: fiq_split: use TTs with more granularity
This fixes certain issues with split transaction scheduling.
- Isochronous multi-packet OUT transactions now hog the TT until
they are completed - this prevents hubs aborting transactions
if they get a periodic start-split out-of-order
- Don't perform TT allocation on non-periodic endpoints - this
allows simultaneous use of the TT's bulk/control and periodic
transaction buffers
This commit will mainly affect USB audio playback.
dwc_otg: fix potential sleep while atomic during urb enqueue
Fixes a regression introduced with eb1b482a. Kmalloc called from
dwc_otg_hcd_qtd_add / dwc_otg_hcd_qtd_create did not always have
the GPF_ATOMIC flag set. Force this flag when inside the larger
critical section.
dwc_otg: make fiq_split_enable imply fiq_fix_enable
Failing to set up the FIQ correctly would result in
"IRQ 32: nobody cared" errors in dmesg.
dwc_otg: prevent crashes on host port disconnects
Fix several issues resulting in crashes or inconsistent state
if a Model A root port was disconnected.
- Clean up queue heads properly in kill_urbs_in_qh_list by
removing the empty QHs from the schedule lists
- Set the halt status properly to prevent IRQ handlers from
using freed memory
- Add fiq_split related cleanup for saved registers
- Make microframe scheduling reclaim host channels if
active during a disconnect
- Abort URBs with -ESHUTDOWN status response, informing
device drivers so they respond in a more correct fashion
and don't try to resubmit URBs
- Prevent IRQ handlers from attempting to handle channel
interrupts if the associated URB was dequeued (and the
driver state was cleared)
dwc_otg: prevent leaking URBs during enqueue
A dwc_otg_urb would get leaked if the HCD enqueue function
failed for any reason. Free the URB at the appropriate points.
dwc_otg: Enable NAK holdoff for control split transactions
Certain low-speed devices take a very long time to complete a
data or status stage of a control transaction, producing NAK
responses until they complete internal processing - the USB2.0
spec limit is up to 500mS. This causes the same type of interrupt
storm as seen with USB-serial dongles prior to c8edb238.
In certain circumstances, usually while booting, this interrupt
storm could cause SD card timeouts.
dwc_otg: Fix for occasional lockup on boot when doing a USB reset
dwc_otg: Don't issue traffic to LS devices in FS mode
Issuing low-speed packets when the root port is in full-speed mode
causes the root port to stop responding. Explicitly fail when
enqueuing URBs to a LS endpoint on a FS bus.
Fix ARM architecture issue with local_irq_restore()
If local_fiq_enable() is called before a local_irq_restore(flags) where
the flags variable has the F bit set, the FIQ will be erroneously disabled.
Fixup arch_local_irq_restore to avoid trampling the F bit in CPSR.
Also fix some of the hacks previously implemented for previous dwc_otg
incarnations.
dwc_otg: fiq_fsm: Base commit for driver rewrite
This commit removes the previous FIQ fixes entirely and adds fiq_fsm.
This rewrite features much more complete support for split transactions
and takes into account several OTG hardware bugs. High-speed
isochronous transactions are also capable of being performed by fiq_fsm.
All driver options have been removed and replaced with:
- dwc_otg.fiq_enable (bool)
- dwc_otg.fiq_fsm_enable (bool)
- dwc_otg.fiq_fsm_mask (bitmask)
- dwc_otg.nak_holdoff (unsigned int)
Defaults are specified such that fiq_fsm behaves similarly to the
previously implemented FIQ fixes.
fiq_fsm: Push error recovery into the FIQ when fiq_fsm is used
If the transfer associated with a QTD failed due to a bus error, the HCD
would retry the transfer up to 3 times (implementing the USB2.0
three-strikes retry in software).
Due to the masking mechanism used by fiq_fsm, it is only possible to pass
a single interrupt through to the HCD per-transfer.
In this instance host channels would fall off the radar because the error
reset would function, but the subsequent channel halt would be lost.
Push the error count reset into the FIQ handler.
fiq_fsm: Implement timeout mechanism
For full-speed endpoints with a large packet size, interrupt latency
runs the risk of the FIQ starting a transaction too late in a full-speed
frame. If the device is still transmitting data when EOF2 for the
downstream frame occurs, the hub will disable the port. This change is
not reflected in the hub status endpoint and the device becomes
unresponsive.
Prevent high-bandwidth transactions from being started too late in a
frame. The mechanism is not guaranteed: a combination of bit stuffing
and hub latency may still result in a device overrunning.
fiq_fsm: fix bounce buffer utilisation for Isochronous OUT
Multi-packet isochronous OUT transactions were subject to a few bounday
bugs. Fix them.
Audio playback is now much more robust: however, an issue stands with
devices that have adaptive sinks - ALSA plays samples too fast.
dwc_otg: Return full-speed frame numbers in HS mode
The frame counter increments on every *microframe* in high-speed mode.
Most device drivers expect this number to be in full-speed frames - this
caused considerable confusion to e.g. snd_usb_audio which uses the
frame counter to estimate the number of samples played.
fiq_fsm: save PID on completion of interrupt OUT transfers
Also add edge case handling for interrupt transports.
Note that for periodic split IN, data toggles are unimplemented in the
OTG host hardware - it unconditionally accepts any PID.
fiq_fsm: add missing case for fiq_fsm_tt_in_use()
Certain combinations of bitrate and endpoint activity could
result in a periodic transaction erroneously getting started
while the previous Isochronous OUT was still active.
fiq_fsm: clear hcintmsk for aborted transactions
Prevents the FIQ from erroneously handling interrupts
on a timed out channel.
fiq_fsm: enable by default
fiq_fsm: fix dequeues for non-periodic split transactions
If a dequeue happened between the SSPLIT and CSPLIT phases of the
transaction, the HCD would never receive an interrupt.
fiq_fsm: Disable by default
fiq_fsm: Handle HC babble errors
The HCTSIZ transfer size field raises a babble interrupt if
the counter wraps. Handle the resulting interrupt in this case.
dwc_otg: fix interrupt registration for fiq_enable=0
Additionally make the module parameter conditional for wherever
hcd->fiq_state is touched.
fiq_fsm: Enable by default
dwc_otg: Fix various issues with root port and transaction errors
Process the host port interrupts correctly (and don't trample them).
Root port hotplug now functional again.
Fix a few thinkos with the transaction error passthrough for fiq_fsm.
fiq_fsm: Implement hack for Split Interrupt transactions
Hubs aren't too picky about which endpoint we send Control type split
transactions to. By treating Interrupt transfers as Control, it is
possible to use the non-periodic queue in the OTG core as well as the
non-periodic FIFOs in the hub itself. This massively reduces the
microframe exclusivity/contention that periodic split transactions
otherwise have to enforce.
It goes without saying that this is a fairly egregious USB specification
violation, but it works.
Original idea by Hans Petter Selasky @ FreeBSD.org.
dwc_otg: FIQ support on SMP. Set up FIQ stack and handler on Core 0 only.
dwc_otg: introduce fiq_fsm_spin(un|)lock()
SMP safety for the FIQ relies on register read-modify write cycles being
completed in the correct order. Several places in the DWC code modify
registers also touched by the FIQ. Protect these by a bare-bones lock
mechanism.
This also makes it possible to run the FIQ and IRQ handlers on different
cores.
fiq_fsm: fix build on bcm2708 and bcm2709 platforms
dwc_otg: put some barriers back where they should be for UP
bcm2709/dwc_otg: Setup FIQ on core 1 if >1 core active
dwc_otg: fixup read-modify-write in critical paths
Be more careful about read-modify-write on registers that the FIQ
also touches.
Guard fiq_fsm_spin_lock with fiq_enable check
fiq_fsm: Falling out of the state machine isn't fatal
This edge case can be hit if the port is disabled while the FIQ is
in the middle of a transaction. Make the effects less severe.
Also get rid of the useless return value.
squash: dwc_otg: Allow to build without SMP
usb: core: make overcurrent messages more prominent
Hub overcurrent messages are more serious than "debug". Increase loglevel.
usb: dwc_otg: Don't use dma_to_virt()
Commit 6ce0d20 changes dma_to_virt() which breaks this driver.
Open code the old dma_to_virt() implementation to work around this.
Limit the use of __bus_to_virt() to cases where transfer_buffer_length
is set and transfer_buffer is not set. This is done to increase the
chance that this driver will also work on ARCH_BCM2835.
transfer_buffer should not be NULL if the length is set, but the
comment in the code indicates that there are situations where this
might happen. drivers/usb/isp1760/isp1760-hcd.c also has a similar
comment pointing to a possible: 'usb storage / SCSI bug'.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Fix crash when fiq_enable=0
dwc_otg: fiq_fsm: Make high-speed isochronous strided transfers work properly
Certain low-bandwidth high-speed USB devices (specialist audio devices,
compressed-frame webcams) have packet intervals > 1 microframe.
Stride these transfers in the FIQ by using the start-of-frame interrupt
to restart the channel at the right time.
dwc_otg: Force host mode to fix incorrect compute module boards
dwc_otg: Add ARCH_BCM2835 support
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Simplify FIQ irq number code
Dropping ATAGS means we can simplify the FIQ irq number code.
Also add error checking on the returned irq number.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Remove duplicate gadget probe/unregister function
dwc_otg: Properly set the HFIR
Douglas Anderson reported:
According to the most up to date version of the dwc2 databook, the FRINT
field of the HFIR register should be programmed to:
* 125 us * (PHY clock freq for HS) - 1
* 1000 us * (PHY clock freq for FS/LS) - 1
This is opposed to older versions of the doc that claimed it should be:
* 125 us * (PHY clock freq for HS)
* 1000 us * (PHY clock freq for FS/LS)
and reported lower timing jitter on a USB analyser
dcw_otg: trim xfer length when buffer larger than allocated size is received
dwc_otg: Don't free qh align buffers in atomic context
dwc_otg: Enable the hack for Split Interrupt transactions by default
dwc_otg.fiq_fsm_mask=0xF has long been a suggestion for users with audio stutters or other USB bandwidth issues.
So far we are aware of many success stories but no failure caused by this setting.
Make it a default to learn more.
See: https://www.raspberrypi.org/forums/viewtopic.php?f=28&t=70437
Signed-off-by: popcornmix <popcornmix@gmail.com>
dwc_otg: Use kzalloc when suitable
dwc_otg: Pass struct device to dma_alloc*()
This makes it possible to get the bus address from Device Tree.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: fix summarize urb->actual_length for isochronous transfers
Kernel does not copy input data of ISO transfers to userspace
if actual_length is set only in ISO transfers and not summarized
in urb->actual_length. Fixesraspberrypi/linux#903
fiq_fsm: Use correct states when starting isoc OUT transfers
In fiq_fsm_start_next_periodic() if an isochronous OUT transfer
was selected, no regard was given as to whether this was a single-packet
transfer or a multi-packet staged transfer.
For single-packet transfers, this had the effect of repeatedly sending
OUT packets with bogus data and lengths.
Eventually if the channel was repeatedly enabled enough times, this
would lock up the OTG core and no further bus transfers would happen.
Set the FSM state up properly if we select a single-packet transfer.
Fixes https://github.com/raspberrypi/linux/issues/1842
dwc_otg: make nak_holdoff work as intended with empty queues
If URBs reading from non-periodic split endpoints were dequeued and
the last transfer from the endpoint was a NAK handshake, the resulting
qh->nak_frame value was stale which would result in unnecessarily long
polling intervals for the first subsequent transfer with a fresh URB.
Fixup qh->nak_frame in dwc_otg_hcd_urb_dequeue and also guard against
a case where a single URB is submitted to the endpoint, a NAK was
received on the transfer immediately prior to receiving data and the
device subsequently resubmits another URB past the qh->nak_frame interval.
Fixes https://github.com/raspberrypi/linux/issues/1709
dwc_otg: fix split transaction data toggle handling around dequeues
See https://github.com/raspberrypi/linux/issues/1709
Fix several issues regarding endpoint state when URBs are dequeued
- If the HCD is disconnected, flush FIQ-enabled channels properly
- Save the data toggle state for bulk endpoints if the last transfer
from an endpoint where URBs were dequeued returned a data packet
- Reset hc->start_pkt_count properly in assign_and_init_hc()
dwc_otg: fix several potential crash sources
On root port disconnect events, the host driver state is cleared and
in-progress host channels are forcibly stopped. This doesn't play
well with the FIQ running in the background, so:
- Guard the disconnect callback with both the host spinlock and FIQ
spinlock
- Move qtd dereference in dwc_otg_handle_hc_fsm() after the early-out
so we don't dereference a qtd that has gone away
- Turn catch-all BUG()s in dwc_otg_handle_hc_fsm() into warnings.
dwc_otg: delete hcd->channel_lock
The lock serves no purpose as it is only held while the HCD spinlock
is already being held.
dwc_otg: remove unnecessary dma-mode channel halts on disconnect interrupt
Host channels are already halted in kill_urbs_in_qh_list() with the
subsequent interrupt processing behaving as if the URB was dequeued
via HCD callback.
There's no need to clobber the host channel registers a second time
as this exposes races between the driver and host channel resulting
in hcd->free_hc_list becoming corrupted.
dwcotg: Allow to build without FIQ on ARM64
Signed-off-by: popcornmix <popcornmix@gmail.com>
dwc_otg: make periodic scheduling behave properly for FS buses
If the root port is in full-speed mode, transfer times at 12mbit/s
would be calculated but matched against high-speed quotas.
Reinitialise hcd->frame_usecs[i] on each port enable event so that
full-speed bandwidth can be tracked sensibly.
Also, don't bother using the FIQ for transfers when in full-speed
mode - at the slower bus speed, interrupt frequency is reduced by
an order of magnitude.
Related issue: https://github.com/raspberrypi/linux/issues/2020
dwc_otg: fiq_fsm: Make isochronous compatibility checks work properly
Get rid of the spammy printk and local pointer mangling.
Also, there is a nominal benefit for using fiq_fsm for isochronous
transfers in FS mode (~1.1k IRQs per second vs 2.1k IRQs per second)
so remove the root port speed check.
dwc_otg: add module parameter int_ep_interval_min
Add a module parameter (defaulting to ignored) that clamps the polling rate
of high-speed Interrupt endpoints to a minimum microframe interval.
The parameter is modifiable at runtime as it is used when activating new
endpoints (such as on device connect).
dwc_otg: fiq_fsm: Add non-periodic TT exclusivity constraints
Certain hub types do not discriminate between pipe direction (IN or OUT)
when considering non-periodic transfers. Therefore these hubs get confused
if multiple transfers are issued in different directions with the same
device address and endpoint number.
Constrain queuing non-periodic split transactions so they are performed
serially in such cases.
Related: https://github.com/raspberrypi/linux/issues/2024
dwc_otg: Fixup change to DRIVER_ATTR interface
dwc_otg: Fix compilation warnings
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
USB_DWCOTG: Disable building dwc_otg as a module (#2265)
When dwc_otg is built as a module, build will fail with the following
error:
ERROR: "DWC_TASK_HI_SCHEDULE" [drivers/usb/host/dwc_otg/dwc_otg.ko] undefined!
scripts/Makefile.modpost:91: recipe for target '__modpost' failed
make[1]: *** [__modpost] Error 1
Makefile:1199: recipe for target 'modules' failed
make: *** [modules] Error 2
Even if the error is solved by including the missing
DWC_TASK_HI_SCHEDULE function, the kernel will panic when loading
dwc_otg.
As a workaround, simply prevent user from building dwc_otg as a module
as the current kernel does not support it.
See: https://github.com/raspberrypi/linux/issues/2258
Signed-off-by: Malik Olivier Boussejra <malik@boussejra.com>
dwc_otg: New timer API
dwc_otg: Fix removed ACCESS_ONCE->READ_ONCE
dwc_otg: don't unconditionally force host mode in dwc_otg_cil_init()
Add the ability to disable force_host_mode for those that want to use
dwc_otg in both device and host modes.
dwc_otg: Fix a regression when dequeueing isochronous transfers
In 282bed95 (dwc_otg: make nak_holdoff work as intended with empty queues)
the dequeue mechanism was changed to leave FIQ-enabled transfers to run
to completion - to avoid leaving hub TT buffers with stale packets lying
around.
This broke FIQ-accelerated isochronous transfers, as this then meant that
dozens of transfers were performed after the dequeue function returned.
Restore the state machine fence for isochronous transfers.
fiq_fsm: rewind DMA pointer for OUT transactions that fail (#2288)
See: https://github.com/raspberrypi/linux/issues/2140
dwc_otg: add smp_mb() to prevent driver state corruption on boot
Occasional crashes have been seen where the FIQ code dereferences
invalid/random pointers immediately after being set up, leading to
panic on boot.
The crash occurs as the FIQ code races against hcd_init_fiq() and
the hcd_init_fiq() code races against the outstanding memory stores
from dwc_otg_hcd_init(). Use explicit barriers after touching
driver state.
usb: dwc_otg: fix memory corruption in dwc_otg driver
[Upstream commit 51b1b64917]
The move from the staging tree to the main tree exposed a
longstanding memory corruption bug in the dwc2 driver. The
reordering of the driver initialization caused the dwc2 driver
to corrupt the initialization data of the sdhci driver on the
Raspberry Pi platform, which made the bug show up.
The error is in calling to_usb_device(hsotg->dev), since ->dev
is not a member of struct usb_device. The easiest fix is to
just remove the offending code, since it is not really needed.
Thanks to Stephen Warren for tracking down the cause of this.
Reported-by: Andre Heider <a.heider@gmail.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[lukas: port from upstream dwc2 to out-of-tree dwc_otg driver]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
usb: dwb_otg: Fix unreachable switch statement warning
This warning appears with GCC 7.3.0 from toolchains.bootlin.com:
../drivers/usb/host/dwc_otg/dwc_otg_fiq_fsm.c: In function ‘fiq_fsm_update_hs_isoc’:
../drivers/usb/host/dwc_otg/dwc_otg_fiq_fsm.c:595:61: warning: statement will never be executed [-Wswitch-unreachable]
st->hctsiz_copy.b.xfersize = nrpackets * st->hcchar_copy.b.mps;
~~~~~~~~~~~~~~~~~^~~~
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
dwc_otg: fiq_fsm: fix incorrect DMA register offset calculation
Rationalise the offset and update all call sites.
Fixes https://github.com/raspberrypi/linux/issues/2408
dwc_otg: fix bug with port_addr assignment for single-TT hubs
See https://github.com/raspberrypi/linux/issues/2734
The "Hub Port" field in the split transaction packet was always set
to 1 for single-TT hubs. The majority of single-TT hub products
apparently ignore this field and broadcast to all downstream enabled
ports, which masked the issue. A subset of hub devices apparently
need the port number to be exact or split transactions will fail.
usb: dwc_otg: Clean up build warnings on 64bit kernels
No functional changes. Almost all are changes to logging lines.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
usb: dwc_otg: Use dma allocation for mphi dummy_send buffer
The FIQ driver used a kzalloc'ed buffer for dummy_send,
passing a kernel virtual address to the hardware block.
The buffer is only ever used for a dummy read, so it
should be harmless, but there is the chance that it will
cause exceptions.
Use a dma allocation so that we have a genuine bus address,
and read from that.
Free the allocation when done for good measure.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
dwc_otg: only do_split when we actually need to do a split
The previous test would fail if the root port was in fullspeed mode
and there was a hub between the FS device and the root port. While
the transfer worked, the schedule mangling performed for high-speed
split transfers would break leading to an 8ms polling interval.
dwc_otg: fix locking around dequeueing and killing URBs
kill_urbs_in_qh_list() is practically only ever called with the fiq lock
already held, so don't spinlock twice in the case where we need to cancel
an isochronous transfer.
Also fix up a case where the global interrupt register could be read with
the fiq lock not held.
Fixes the deadlock seen in https://github.com/raspberrypi/linux/issues/2907
ARM64/DWC_OTG: Port dwc_otg driver to ARM64
In ARM64, the FIQ mechanism used by this driver is not current
implemented. As a workaround, reqular IRQ is used instead
of FIQ.
In a separate change, the IRQ-CPU mapping is round robined
on ARM64 to increase concurrency and allow multiple interrupts
to be serviced at a time. This reduces the need for FIQ.
Tests Run:
This mechanism is most likely to break when multiple USB devices
are attached at the same time. So the system was tested under
stress.
Devices:
1. USB Speakers playing back a FLAC audio through VLC
at 96KHz.(Higher then typically, but supported on my speakers).
2. sftp transferring large files through the buildin ethernet
connection which is connected through USB.
3. Keyboard and mouse attached and being used.
Although I do occasionally hear some glitches, the music seems to
play quite well.
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
usb: dwc_otg: Clean up interrupt claiming code
The FIQ/IRQ interrupt number identification code is scattered through
the dwc_otg driver. Rationalise it, simplifying the code and solving
an existing issue.
See: https://github.com/raspberrypi/linux/issues/2612
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
dwc_otg: Choose appropriate IRQ handover strategy
2711 has no MPHI peripheral, but the ARM Control block can fake
interrupts. Use the size of the DTB "mphi" reg block to determine
which is required.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
usb: host: dwc_otg: fix compiling in separate directory
The dwc_otg Makefile does not respect the O=path argument correctly:
include paths in CFLAGS are given relatively to object path, not source
path. Compiling in a separate directory yields #include errors.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
dwc_otg: use align_buf for small IN control transfers (#3150)
The hardware will do a 4-byte write to memory on any IN packet received
that is between 1 and 3 bytes long. This tramples memory in the uvcvideo
driver, as it uses a sequence of 1- and 2-byte control transfers to
query the min/max/range/step of each individual camera control and
gives us buffers that are offsets into a struct.
Catch small control transfers in the data phase and use the align_buf
to bounce the correct number of bytes into the URB's buffer.
In general, short packets on non-control endpoints should be OK as URBs
should have enough buffer space for a wMaxPacket size transfer.
See: https://github.com/raspberrypi/linux/issues/3148
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
dwc_otg: Declare DMA capability with HCD_DMA flag
Following [1], USB controllers have to declare DMA capabilities in
order for them to be used by adding the HCD_DMA flag to their hc_driver
struct.
[1] 7b81cb6bdd ("usb: add a HCD_DMA flag instead of guestimating DMA capabilities")
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
dwc_otg: checking the urb->transfer_buffer too early (#3332)
After enable the HIGHMEM and VMSPLIT_3G, the dwc_otg driver doesn't
work well on Pi2/3 boards with 1G physical ram. Users experience
the failure when copying a file of 600M size to the USB stick. And
at the same time, the dmesg shows:
usb 1-1.1.2: reset high-speed USB device number 8 using dwc_otg
sd 0:0:0:0: [sda] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
blk_update_request: I/O error, dev sda, sector 3024048 op 0x1:(WRITE) flags 0x4000 phys_seg 15 prio class 0
When this happens, the sg_buf sent to the driver is located in the
highmem region, the usb_sg_init() in the core/message.c will leave
transfer_buffer to NULL if the sg_buf is in highmem, but in the
dwc_otg driver, it returns -EINVAL unconditionally if transfer_buffer
is NULL.
The driver can handle the situation of buffer to be NULL, if it is in
DMA mode, it will convert an address from transfer_dma.
But if the conversion fails or it is in the PIO mode, we should check
buffer and return -EINVAL if it is NULL.
BugLink: https://bugs.launchpad.net/bugs/1852510
Signed-off-by: Hui Wang <hui.wang@canonical.com>
dwc_otg: constrain endpoint max packet and transfer size on split IN
The hcd would unconditionally set the transfer length to the endpoint
packet size for non-isoc IN transfers. If the remaining buffer length
was less than the length of returned data, random memory would get
scribbled over, with bad effects if it crossed a page boundary.
Force a babble error if this happens by limiting the max transfer size
to the available buffer space. DMA will stop writing to memory on a
babble condition.
The hardware expects xfersize to be an integer multiple of maxpacket
size, so override hcchar.b.mps as well.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
dwc_otg: fiq_fsm: pause when cancelling split transactions
Non-periodic splits will DMA to/from the driver-provided transfer_buffer,
which may be freed immediately after the dequeue call returns. Block until
we know the transfer is complete.
A similar delay is needed when cleaning up disconnects, as the FIQ could
have started a periodic transfer in the previous microframe to the one
that triggered a disconnect.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
dwc_otg: fiq_fsm: add a barrier on entry into FIQ handler(s)
On BCM2835, there is no hardware guarantee that multiple outstanding
reads to different peripherals will complete in-order. The FIQ code
uses peripheral reads without barriers for performance, so in the case
where a read to a slow peripheral was issued immediately prior to FIQ
entry, the first peripheral read that the FIQ did could end up with
wrong read data returned.
Add dsb(sy) on entry so that all outstanding reads are retired.
The FIQ only issues reads to the dwc_otg core, so per-read barriers
in the handler itself are not required.
On BCM2836 and BCM2837 the barrier is not strictly required due to
differences in how the peripheral bus is implemented, but having
arch-specific handlers that introduce different latencies is risky.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
dwc_otg: whitelist_table is now productlist_table
dwc_otg: initialise sched_frame for periodic QHs that were parked
If a periodic QH has no remaining QTDs, then it is removed from all
periodic schedules. When re-adding, initialise the sched_frame and
start_split_frame from the current value of the frame counter.
See https://bugs.launchpad.net/raspbian/+bug/1819560
and
https://github.com/raspberrypi/linux/issues/3883
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
dwc_otg: Minimise header and fix build warnings
Delete a large amount of unused declaration from "usb.h", some of which
were causing build warnings, and get the module building cleanly.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
dwc-otg: fix clang -Wignored-attributes warning
warning: attribute declaration must precede definition
dwc-otg: fix clang -Wsometimes-uninitialized warning
warning: variable 'retval' is used uninitialized whenever 'if' condition is false
dwc-otg: fix clang -Wpointer-bool-conversion warning
warning: address of array 'desc->wMaxPacketSize' will always evaluate to 'true'
The wMaxPacketSize field is actually a two element array which content should
be accessed via the UGETW macro.
dwc_otg: fix an undeclared variable
Replace an undeclared variable used by DWC_DEBUGPL with the real endpoint address. DWC_DEBUGPL does nothing with DEBUG undefined so it did not go wrong before.
Signed-off-by: Zixuan Wang <wangzixuan@sjtu.edu.cn>
dwc_otg: Update NetBSD usb.h header licence
NetBSD have changed their licensing requirements such that the 2-clause
licence is preferred. Update usb.h in the downstream dwc_otg code
accordingly.
See https://www.netbsd.org/about/redistribution.html for more
information.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
dwc_otg: pay attention to qh->interval when rescheduling periodic queues
A regression introduced in https://github.com/raspberrypi/linux/pull/3887
meant that if the newly scheduled transfer immediately returned data, and
the driver resubmitted a single URB after every transfer, then the effective
polling interval would end up being approx 1ms.
Use the larger of SCHEDULE_SLOP or the configured endpoint interval.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Signed-off-by: popcornmix <popcornmix@gmail.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2709: Drop platform smp and timer init code
irq-bcm2836 handles this through these functions:
bcm2835_init_local_timer_frequency()
bcm2836_arm_irqchip_smp_init()
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm270x: Use watchdog for reboot/poweroff
The watchdog driver already has support for reboot/poweroff.
Make use of this and remove the code from the platform files.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
board_bcm2835: Remove coherent dma pool increase - API has gone
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
SQUASH: pinctrl: bcm2835: Set base for bcm2711 GPIO to 0
Without this patch GPIOs don't seem to work properly, primarily
noticeable as broken LEDs.
Squash with "pinctrl-bcm2835: Set base to 0 give expected gpio numbering"
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Under some circumstances on BCM283x processors data loss can be
observed - a single byte missing from the TX output stream. These bytes
are always the last byte of a batch of 8 written from pl011_tx_chars
when from_irq is true, meaning that the FIFO full flag is not checked
before writing.
The transmit optimisation relies on the FIFO being half-empty when the
TX interrupt is raised. Instrumenting the driver further showed that
the failure case correlated with the TX FIFO full flag being set at the
point where the last byte was written to the data register, which
explains the data loss but not how the FIFO appeared to be prematurely
full. A possible explanation is that a FIFO write was in flight at the
time the interrupt was raised, but as yet there is no hypothesis as to
how this might occur.
In the absence of a clear understanding of the failure mechanism, avoid
the problem by checking the FIFO levels before writing the last byte of
the group, which will have minimal performance impact.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The BCM2835 PL011 implementation seems to have a bug that can lead to a
transmission lockup if CTS changes frequently. A workaround was added to
the driver with a vendor-specific flag to enable it, but this flag is
currently not set for ARM implementations.
Add a "cts-event-workaround" property to Pi DTBs and use the presence
of that property to force the flag to be enabled in the driver.
See: https://github.com/raspberrypi/linux/issues/1280
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The pl011 register accessor functions use the _relaxed versions of the
standard readl() and writel() functions, meaning that there are no
automatic memory barriers. When polling a FIFO status register to check
for fullness, it is necessary to ensure that any outstanding writes have
completed; otherwise the flags are effectively stale, making it possible
that the next write is to a full FIFO.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The UART clock is initialised to be as close to the requested
frequency as possible without exceeding it. Now that there is a
clock manager that returns the actual frequencies, an expected
48MHz clock is reported as 47999625. If the requested baudrate
== requested clock/16, there is no headroom and the slight
reduction in actual clock rate results in failure.
Detect cases where it looks like a "round" clock was chosen and
adjust the reported clock to match that "round" value. As the
code comment says:
/*
* If increasing a clock by less than 0.1% changes it
* from ..999.. to ..000.., round up.
*/
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The pl011 driver looks for DT aliases of the form "serial<n>",
and if found uses <n> as the device ID. This can cause
/dev/ttyAMA0 to become /dev/ttyAMA1, which is confusing if the
other serial port is provided by the 8250 driver which doesn't
use the same logic.
For applications of the LAN78xx that don't have valid programmed
EEPROMs or OTPs, enabling both LEDs and auto-negotiation by default
seems reasonable.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The syscon node defines a register range that duplicates that used by
the local_intc node on bcm2836/7. Since irq-bcm2835 and irq-bcm2836 are
built in and always present together (both drivers are enabled by
CONFIG_ARCH_BCM2835), it is possible to replace the syscon usage with a
global variable that simplifies the code. Doing so does lose the
locking provided by regmap, but as only one side is using the regmap
interface (irq-bcm2835 uses readl and write) there is no loss of
atomicity.
See: https://github.com/raspberrypi/firmware/issues/926
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
This adds a debug module parameter to aid in debugging transfer issues
by printing info to the kernel log. When enabled, status values are
collected in the interrupt routine and msg info in
bcm2835_i2c_start_transfer(). This is done in a way that tries to avoid
affecting timing. Having printk in the isr can mask issues.
debug values (additive):
1: Print info on error
2: Print info on all transfers
3: Print messages before transfer is started
The value can be changed at runtime:
/sys/module/i2c_bcm2835/parameters/debug
Example output, debug=3:
[ 747.114448] bcm2835_i2c_xfer: msg(1/2) write addr=0x54, len=2 flags= [i2c1]
[ 747.114463] bcm2835_i2c_xfer: msg(2/2) read addr=0x54, len=32 flags= [i2c1]
[ 747.117809] start_transfer: msg(1/2) write addr=0x54, len=2 flags= [i2c1]
[ 747.117825] isr: remain=2, status=0x30000055 : TA TXW TXD TXE [i2c1]
[ 747.117839] start_transfer: msg(2/2) read addr=0x54, len=32 flags= [i2c1]
[ 747.117849] isr: remain=32, status=0xd0000039 : TA RXR TXD RXD [i2c1]
[ 747.117861] isr: remain=20, status=0xd0000039 : TA RXR TXD RXD [i2c1]
[ 747.117870] isr: remain=8, status=0x32 : DONE TXD RXD [i2c1]
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Christopher Alexander Tobias Schulze - May 2, 2015, 11:57 a.m.
This patch fixes a problem with VFP state save and restore related
to exception handling (panic with message "BUG: unsupported FP
instruction in kernel mode") present on VFP11 floating point units
(as used with ARM1176JZF-S CPUs, e.g. on first generation Raspberry
Pi boards). This patch was developed and discussed on
https://github.com/raspberrypi/linux/issues/859
A precondition to see the crashes is that floating point exception
traps are enabled. In this case, the VFP11 might determine that a FPU
operation needs to trap at a point in time when it is not possible to
signal this to the ARM11 core any more. The VFP11 will then set the
FPEXC.EX bit and store the trapped opcode in FPINST. (In some cases,
a second opcode might have been accepted by the VFP11 before the
exception was detected and could be reported to the ARM11 - in this
case, the VFP11 also sets FPEXC.FP2V and stores the second opcode in
FPINST2.)
If FPEXC.EX is set, the VFP11 will "bounce" the next FPU opcode issued
by the ARM11 CPU, which will be seen by the ARM11 as an undefined opcode
trap. The VFP support code examines the FPEXC.EX and FPEXC.FP2V bits
to decide what actions to take, i.e., whether to emulate the opcodes
found in FPINST and FPINST2, and whether to retry the bounced instruction.
If a user space application has left the VFP11 in this "pending trap"
state, the next FPU opcode issued to the VFP11 might actually be the
VSTMIA operation vfp_save_state() uses to store the FPU registers
to memory (in our test cases, when building the signal stack frame).
In this case, the kernel crashes as described above.
This patch fixes the problem by making sure that vfp_save_state() is
always entered with FPEXC.EX cleared. (The current value of FPEXC has
already been saved, so this does not corrupt the context. Clearing
FPEXC.EX has no effects on FPINST or FPINST2. Also note that many
callers already modify FPEXC by setting FPEXC.EN before invoking
vfp_save_state().)
This patch also addresses a second problem related to FPEXC.EX: After
returning from signal handling, the kernel reloads the VFP context
from the user mode stack. However, the current code explicitly clears
both FPEXC.EX and FPEXC.FP2V during reload. As VFP11 requires these
bits to be preserved, this patch disables clearing them for VFP
implementations belonging to architecture 1. There should be no
negative side effects: the user can set both bits by executing FPU
opcodes anyway, and while user code may now place arbitrary values
into FPINST and FPINST2 (e.g., non-VFP ARM opcodes) the VFP support
code knows which instructions can be emulated, and rejects other
opcodes with "unhandled bounce" messages, so there should be no
security impact from allowing reloading FPEXC.EX and FPEXC.FP2V.
Signed-off-by: Christopher Alexander Tobias Schulze <cat.schulze@alice-dsl.net>
At present there is no mechanism to specify driver load order,
which can lead to deferrals and repeated retries until successful.
Since this situation is expected, reduce the dmesg level to
INFO and mention that the operation will be retried.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The Raspberry Pi firmware looks at the RSTS register to know which
partition to boot from. The reboot syscall command
LINUX_REBOOT_CMD_RESTART2 supports passing in a string argument.
Add support for passing in a partition number 0..63 to boot from.
Partition 63 is a special partiton indicating halt.
If the partition doesn't exist, the firmware falls back to partition 0.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Load driver early since at least bcm2708_fb doesn't support deferred
probing and even if it did, we don't want the video driver deferred.
Support the legacy DMA API which is needed by bcm2708_fb.
Don't mask out channel 2.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
An alternative strategy would be to use "rpi,spidev" instead, but that
would require many Raspberry Pi Device Tree changes.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Add a duplicate irq range with an offset on the hwirq's so the
driver can detect that enable_fiq() is used.
Tested with downstream dwc_otg USB controller driver.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: popcornmix <popcornmix@gmail.com>
SQUASH: smsc95xx: Use dev_mod_addr to set MAC addr
Since adeef3e321 ("net: constify netdev->dev_addr") it has been
illegal to write to the dev_addr MAC address field. Later commits
have added explicit checks that it hasn't been modified by nefarious
means. The dev_addr_mod helper function is the accepted way to change
the dev_addr field, so use it.
Squash with 96c1def63ee1 ("Allow mac address to be set in smsc95xx").
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
smsc95xx is adjusting truesize when it shouldn't, and following a recent patch from Eric this is now triggering warnings.
This patch stops smsc95xx from changing truesize.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
This reverts commit 92516cd97f.
Thi commit "Bluetooth: Always request for user confirmation for Just
Works" prevents BLE devices pairing in (at least) the Raspberry Pi OS
GUI. After reverting it, pairing works again.
If another solution to the problem is found then this reversion will
be removed.
See: https://github.com/raspberrypi/linux/issues/4139
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
This reverts commit ffee202a78.
The commit "Bluetooth: Always request for user confirmation for Just
Works" prevents BLE devices pairing in (at least) the Raspberry Pi OS
GUI. After reverting it, pairing works again. Although this companion
commit ("... (LE SC)") has not been demonstrated to be problematic,
it follows the same logic and therefore could affect some use cases.
If another solution to the problem is found then this reversion will
be removed.
See: https://github.com/raspberrypi/linux/issues/4139
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The fw_node pointer has already been retrieved, and using it allows
us to remove a downstream patch to the firmware driver.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
This falls under the same "we can reprogram glitch-free as long as we
pause generation" rule as updating the div/frac fields. This can be
used for runtime reclocking of V3D to manage power leakage.
Signed-off-by: Eric Anholt <eric@anholt.net>
The debug text for how many clocks have been registered
uses "%d" with a size_t. Correct it to "%zd".
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The VPU is responsible for managing the core clock, usually under
direction from the bcm2835-cpufreq driver but not via the clk-bcm2835
driver. Since the core frequency can change without warning, it is
safer to report the maximum clock rate to users of the core clock -
I2C, SPI and the mini UART - to err on the safe side when calculating
clock divisors.
If the DT node for the clock driver includes a reference to the
firmware node, use the firmware API to query the maximum core clock
instead of reading the divider registers.
Prior to this patch, a "100KHz" I2C bus was sometimes clocked at about
160KHz. In particular, switching to the 4.9 kernel was likely to break
SenseHAT usage on a Pi3.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The claim-clocks property can be used to prevent PLLs and dividers
from being marked as critical. It contains a vector of clock IDs,
as defined by dt-bindings/clock/bcm2835.h.
Use this mechanism to claim PLLD_DSI0, PLLD_DSI1, PLLH_AUX and
PLLH_PIX for the vc4_kms_v3d driver.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The VPU configures and relies on several PLLs and dividers. Mark all
enabled dividers and their PLLs as CRITICAL to prevent the kernel from
switching them off.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Add the bare minimum needed to boot BCM2708 from a Device Tree.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
BCM2708: DT: change 'axi' nodename to 'soc'
Change DT node named 'axi' to 'soc' so it matches ARCH_BCM2835.
The VC4 bootloader fills in certain properties in the 'axi' subtree,
but since this is part of an upstreaming effort, the name is changed.
Signed-off-by: Noralf Tronnes notro@tronnes.org
BCM2708_DT: Correct length of the peripheral space
Use dts-dirs feature for overlays.
The kernel makefiles have a dts-dirs target that is for vendor subdirectories.
Using this fixes the install_dtbs target, which previously did not install the overlays.
BCM270X_DT: configure I2S DMA channels
Signed-off-by: Matthias Reichl <hias@horus.com>
BCM270X_DT: switch to bcm2835-i2s
I2S soundcard drivers with proper devicetree support (i.e. not linking
to the cpu_dai/platform via name but to cpu/platform via of_node)
will work out of the box without any modifications.
When the kernel is compiled without devicetree support the platform
code will instantiate the bcm2708-i2s driver and I2S soundcard drivers
will link to it via name, as before.
Signed-off-by: Matthias Reichl <hias@horus.com>
SDIO-overlay: add poll_once-boolean parameter
Add paramter to toggle sdio-device-polling
done every second or once at boot-time.
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
BCM270X_DT: Make mmc overlay compatible with current firmware
The original DT overlay logic followed a merge-then-patch procedure,
i.e. parameters are applied to the loaded overlay before the overlay
is merged into the base DTB. This sequence has been changed to
patch-then-merge, in order to support parameterised node names, and
to protect against bad overlays. As a result, overrides (parameters)
must only target labels in the overlay, but the overlay can obviously target nodes in the base DTB.
mmc-overlay.dts (that switches back to the original mmc sdcard
driver) is the only overlay violating that rule, and this patch
fixes it.
bcm270x_dt: Use the sdhost MMC controller by default
The "mmc" overlay reverts to using the other controller.
squash: Add cprman to dt
BCM270X_DT: Use clk_core for I2C interfaces
BCM270X_DT: Use bcm283x.dtsi, bcm2835.dtsi and bcm2836.dtsi
The mainline Device Tree files are quite close to downstream now.
Let's use bcm283x.dtsi, bcm2835.dtsi and bcm2836.dtsi as base files
for our dts files.
Mainline dts files are based on these files:
bcm2835-rpi.dtsi
bcm2835.dtsi bcm2836.dtsi
bcm283x.dtsi
Current downstream are based on these:
bcm2708.dtsi bcm2709.dtsi bcm2710.dtsi
bcm2708_common.dtsi
This patch introduces this dependency:
bcm2708.dtsi bcm2709.dtsi
bcm2708-rpi.dtsi
bcm270x.dtsi
bcm2835.dtsi bcm2836.dtsi
bcm283x.dtsi
And:
bcm2710.dtsi
bcm2708-rpi.dtsi
bcm270x.dtsi
bcm283x.dtsi
bcm270x.dtsi contains the downstream bcm283x.dtsi diff.
bcm2708-rpi.dtsi is the downstream version of bcm2835-rpi.dtsi.
Other changes:
- The led node has moved from /soc/leds to /leds. This is not a problem
since the label is used to reference it.
- The clk_osc reg property changes from 6 to 3.
- The gpu nodes has their interrupt property set in the base file.
- the clocks label does not point to the /clocks node anymore, but
points to the cprman node. This is not a problem since the overlays
that use the clock node refer to it directly: target-path = "/clocks";
- some nodes now have 2 labels since mainline and downstream differs in
this respect: cprman/clocks, spi0/spi, gpu/vc4.
- some nodes doesn't have an explicit status = "okay" since they're not
disabled in the base file: watchdog and random.
- gpiomem doesn't need an explicit status = "okay".
- bcm2708-rpi-cm.dts got the hpd-gpios property from bcm2708_common.dtsi,
it's now set directly in that file.
- bcm2709-rpi-2-b.dts has the timer node moved from /soc/timer to /timer.
- Removed clock-frequency property on the bcm{2709,2710}.dtsi timer nodes.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270X_DT: Use raspberrypi-power to turn on USB power
Use the raspberrypi-power driver to turn on USB power.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270X_DT: Add a .dtbo target, use for overlays
Change the filenames and extensions to keep the pre-DDT style of
overlay (<name>-overlay.dtb) distinct from new ones that use a
different style of local fixups (<name>.dtbo), and to match other
platforms.
The RPi firmware uses the DDTK trailer atom to choose which type of
overlay to use for each kernel.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Don't generate "linux,phandle" props
The EPAPR standard says to use "phandle" properties to store phandles,
rather than the deprecated "linux,phandle" version. By default, dtc
generates both, but adding "-H epapr" causes it to only generate
"phandle"s, saving some space and clutter.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Add overlay for enc28j60 on SPI2
Works on SPI2 for compute module
BCM270X_DT: Add midi-uart0 overlay
MIDI requires 31.25kbaud, a baudrate unsupported by Linux. The
midi-uart0 overlay configures uart0 (ttyAMA0) to use a fake clock
so that requesting 38.4kbaud actually gets 31.25kbaud.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Add i2c-sensor overlay
The i2c-sensor overlay is a container for various pressure and
temperature sensors, currently bmp085 and bmp280. The standalone
bmp085_i2c-sensor overlay is now deprecated.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: overlays/*-overlay.dtb -> overlays/*.dtbo (#1752)
We now create overlays as .dtbo files.
build: support for .dtbo files for dtb overlays
Kernel 4.4.6+ on RaspberryPi support .dtbo files for overlays, instead of .dtb.
Patch the kernel, which has faulty rules to generate .dtbo the way yocto does
Signed-off-by: Herve Jourdain <herve.jourdain@neuf.fr>
Signed-off-by: Khem Raj <raj.khem@gmail.com>
BCM270X: Drop position requirement for CMA in VC4 overlay.
No longer necessary since 2aefcd5761,
and will probably let peeople that want to choose a larger CMA
allocation (particularly on pi0/1).
Signed-off-by: Eric Anholt <eric@anholt.net>
BCM270X_DT: RPi Device Tree tidy
Use the upstream sdhost node, add thermal-zones, and factor out some
common elements.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
kbuild: Silence unhelpful DTC warnings
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: DT build rules no longer arch-specific
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
This aligns vc4 with Intel, AMD and Synopsis drivers and fixes max bpc
connector property not working as expected on monitors with YCbCr 4:2:2
support but not deep color support.
max_bpc in connector state is clamped at max_bpc from display info and
the latter only takes deep color modes into account so it will always
be 8, even if the display can do 4:2:2 12-bit output.
Signed-off-by: Matthias Reichl <hias@horus.com>
Support displaying DRM_FORMAT_YUV444 and DRM_FORMAT_YVU444 formats.
Tested with kmstest and kodi. e.g.
kmstest -r 1920x1080@60 -f 400x300-YU24
Note: without the shift of width, only half the chroma is fetched,
resulting in correct left half of image and corrupt colours on right half.
The increase in width shouldn't affect fetching of Y data,
as the hardware will clamp at dest width.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
When running a kunit test, the driver runs with a mock device. As such,
any attempt to read or write to a hardware register will fail the
current test immediately.
The dlist allocation management recently introduced will read the
current frame count from the HVS to defer its destruction until a
subsequent frame has been output. This obviously involves a register
read that fails the Kunit tests.
Change the destruction deferral function to destroy the allocation
immediately if we run under kunit. This is essentially harmless since
the main reason for that deferall is to prevent any access to the
hardware dlist while a frame described by that list is rendered. On our
mock driver, we have neither a hardware dlist nor a rendering, so it
doesn't matter.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
We'll need to destroy a dlist allocation in multiple code paths, so
let's move it to a separate function.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The vc4_hvs_dlist_allocation structure has a list that we don't
initialize when we allocate a new instance.
This makes any call reading the list structure (such as list_empty) fail
with a NULL pointer dereference.
Let's make sure our list is always initialized.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
During normal operations, the cursor position update is done through an
asynchronous plane update, which on the vc4 driver basically just
modifies the right dlist word to move the plane to the new coordinates.
However, when we have the overscan margins setup, we fall back to a
regular commit when we are next to the edges. And since that commit
happens to be on a cursor plane, it's considered a legacy cursor update
by KMS.
The main difference it makes is that it won't wait for its completion
(ie, next vblank) before returning. This means if we have multiple
commits happening in rapid succession, we can have several of them
happening before the next vblank.
In parallel, our dlist allocation is tied to a CRTC state, and each time
we do a commit we end up with a new CRTC state, with the previous one
being freed. This means that we free our previous dlist entry (but don't
clear it though) every time a new one is being committed.
Now, if we were to have two commits happening before the next vblank, we
could end up freeing reusing the same dlist entries before the next
vblank.
Indeed, we would start from an initial state taking, for example, the
dlist entries 10 to 20, then start a commit taking the entries 20 to 30
and setting the dlist pointer to 20, and freeing the dlist entries 10 to
20. However, since we haven't reach vblank yet, the HVS is still using
the entries 10 to 20.
If we were to make a new commit now, chances are the allocator are going
to give the 10 to 20 entries back, and we would change their content to
match the new state. If vblank hasn't happened yet, we just corrupted
the active dlist entries.
A first attempt to solve this was made by creating an intermediate dlist
buffer to store the current (ie, as of the last commit) dlist content,
that we would update each time the HVS is done with a frame. However, if
the interrupt handler missed the vblank window, we would end up copying
our intermediate dlist to the hardware one during the composition,
essentially creating the same issue.
Since making sure that our interrupt handler runs within a fixed,
constrained, time window would require to make Linux a real-time kernel,
this seems a bit out of scope.
Instead, we can work around our original issue by keeping the dlist
slots allocation longer. That way, we won't reuse a dlist slot while
it's still in flight. In order to achieve this, instead of freeing the
dlist slot when its associated CRTC state is destroyed, we'll queue it
in a list.
A naive implementation would free the buffers in that queue when we get
our end of frame interrupt. However, there's still a race since, just
like in the shadow dlist case, we don't control when the handler for
that interrupt is going to run. Thus, we can end up with a commit adding
an old dlist allocation to our queue during the window between our
actual interrupt and when our handler will run. And since that buffer is
still being used for the composition of the current frame, we can't free
it right away, exposing us to the original bug.
Fortunately for us, the hardware provides a frame counter that is
increased each time the first line of a frame is being generated.
Associating the frame counter the image is supposed to go away to the
allocation, and then only deallocate buffers that have a counter below
or equal to the one we see when the deallocation code should prevent the
above race from occuring.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Add a custom property "Output format" that allows the overriding
of the default colourspace choice in the way that the old
firmware hdmi_pixel_encoding property did. If the chosen format is not
supported, then it will still drop back to the older behaviour.
This won't be acceptable to upstream, but it adds back the missing
functionality of hdmi_pixel_encoding.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The CSC requires the coefficients to be swapped around for
4:4:4 mode, but the swap was incorrectly defined.
Correct the swap.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
We regularly get dmesg error reports of:
[ 18.184066] hdmi-audio-codec hdmi-audio-codec.3.auto: ASoC: error at snd_soc_dai_startup on i2s-hifi: -19
[ 18.184098] MAI: soc_pcm_open() failed (-19)
Currently I get 30 of these when booting to desktop.
We always say, ignore they are harmless, but removing them would be good.
A bit of investigation shows, for me, the errors are all generated by second, unused hdmi interface.
It shows as an alsa device, and pulseaudio attempts to open it (numerous times), generating a kernel
error message each time.
systemctl --user restart pulseaudio.service generates 6 additional error messages.
The error messages all come through:
a009a9c0d7/sound/soc/soc-pcm.c (L39)
which suggests returning ENOTSUPP, rather that ENODEV will be quiet. And indeed it is.
Note: earlier kernels do not have the quiet ENOTSUPP, so additional cherry-picks will be needed to backport
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
See: https://forum.libreelec.tv/thread/24783-tv-avr-turns-back-on-right-after-turning-them-off
While the kernel provides a :D flag for assuming device is connected,
it doesn't stop this function from being called and generating a cec_phys_addr_invalidate
message when hotplug is deasserted.
That message provokes a flurry of CEC messages which for many users results in the TV
switching back on again and it's very hard to get it to stay switched off.
It seems to only occur with an AVR and TV connected but has been observed across a
number of manufacturers.
The issue started with https://github.com/raspberrypi/linux/pull/4371
and this provides an optional way of getting back the old behaviour
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
The missing 32-bit per pixel ABGR and various "RGB with an X value"
formats are added. Change sent by Dave Stevenson.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
FKMS doesn't have an HVS and it's expected. Return from the debugfs init
function immediately if we're running with fkms.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Now that cursors are implemented as regular planes, all cursor
movements result in atomic updates. As the firmware-kms driver
doesn't support asynchronous updates, these are synchronous, which
limits the update rate to the screen refresh rate. Xorg seems unaware
of this (or at least of the effect of this), because if the mouse is
configured with a higher update rate than the screen then continuous
mouse movement results in an increasing backlog of mouse events -
cue extreme lag.
Add minimal support for asynchronous updates - limited to cursor
planes - to eliminate the lag.
See: https://github.com/raspberrypi/linux/pull/4971https://github.com/raspberrypi/linux/issues/4988
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Margins may be implemented by scaling the planes, but as there
is no way of intercepting the set_property for a standard property,
and all planes are checked in drm_atomic_check_only before the
connectors, there's now way to add the planes into the state
from the driver.
If the margin properties change, add all corresponding planes to
the state.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The stuff never really worked, and leads to lots of fun because it
out-of-order frees atomic states. Which upsets KASAN, among other
things.
For async updates we now have a more solid solution with the
->atomic_async_check and ->atomic_async_commit hooks. Support for that
for msm and vc4 landed. nouveau and i915 have their own commit
routines, doing something similar.
For everyone else it's probably better to remove the use-after-free
bug, and encourage folks to use the async support instead. The
affected drivers which register a legacy cursor plane and don't either
use the new async stuff or their own commit routine are: amdgpu,
atmel, mediatek, qxl, rockchip, sti, sun4i, tegra, virtio, and vmwgfx.
Inspired by an amdgpu bug report.
v2: Drop RFC, I think with amdgpu converted over to use
atomic_async_check/commit done in
commit 674e78acae
Author: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Date: Wed Dec 5 14:59:07 2018 -0500
drm/amd/display: Add fast path for cursor plane updates
we don't have any driver anymore where we have userspace expecting
solid legacy cursor support _and_ they are using the atomic helpers in
their fully glory. So we can retire this.
v3: Paper over msm and i915 regression. The complete_all is the only
thing missing afaict.
v4: Rebased on recent kernel, added extra link for vc4 bug.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199425
Link: https://lore.kernel.org/all/20220221134155.125447-9-maxime@cerno.tech/
Cc: mikita.lipski@amd.com
Cc: Michel Dänzer <michel@daenzer.net>
Cc: harry.wentland@amd.com
Cc: Rob Clark <robdclark@gmail.com>
Cc: "Kazlauskas, Nicholas" <nicholas.kazlauskas@amd.com>
Tested-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
When the margins are changed, the dlist needs to be regenerated
with the changed updated dest regions for each of the planes.
Setting the zpos_changed flag is sufficient to trigger that
without doing a full modeset, therefore set it should the
margins be changed.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The HVS always composes in the RGB domain, but there is a colourspace
conversion block on the output to allow for sending YCbCr over the
HDMI interface.
The colourspace on that link is configurable via the "Colorspace"
property on the connector, and that updates the infoframes. There
is also selection of limited or full range based on the mode selected
or an override.
Add code to update the CSC as well so that the metadata matches the
image data.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
TC358762 wants the DSI host to be prepared before it is powered up, so
set the flag to request that the upstream bridges have their
pre_enable called first.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
mipi_dsi_attach can fail due to resources not being available
yet, therefore do not log error messages should they occur.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The MIPI_DSI_MODE_* flags have fairly terse descriptions and no reference
to the DSI specification as to their exact meaning. Usage has therefore
been rather fluid.
Extend the descriptions and provide references to the part of the
MIPI DSI specification regarding what they mean.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Current usage of drm_connector_set_panel_orientation is from a panel's
get_modes call. However if the panel orientation property doesn't
exist on the connector at this point, then drm_mode_object triggers
WARNs as the connector is already registered.
Add an orientation variable to struct drm_panel and initialise it from
drm_panel_init.
panel_bridge_attach can then create the property before the connector
is registered.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Copy Intel's "Broadcast RGB" property semantics to add manual override
of the HDMI pixel range for monitors that don't abide by the content
of the AVI Infoframe.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Still under investigation, but the conditions under which the HVS
will accept values written to the gamma PWL are not straightforward.
Disable gamma on HVS5 again until it can be resolved to avoid
gamma being enabled with an incorrect table.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add a check to vc4_hvs_gamma_check to ensure a new non-empty
gamma LUT is of the correct length before accepting it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Two calls were made to drm_crtc_enable_color_mgmt to add gamma
and CTM, however they were both set to add the gamma properties,
so they ended up added twice.
Fixes: 766cc6b1f7 "drm/vc4: Add CTM support"
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
With HVS5 the gamma block is now only reprogrammed with
a disable/enable. Loading the table from vc4_hvs_init_channel
(called from vc4_hvs_atomic_enable) appears to be at an
invalid point in time and so isn't applied.
Switch to enabling and disabling the gamma table instead. This
isn't safe if the pipeline is running, but it isn't now.
For HVS4 it is safe to enable and disable dynamically, so
adopt that approach there too.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm_crtc_legacy_gamma_set updates the gamma_lut blob unconditionally,
which leads to unnecessary reprogramming of hardware.
Check whether the blob contents has actually changed before
signalling that it has been updated.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add predefined modelines for the 240p (NTSC) and 288p (PAL) progressive
modes, and report them through vc4_vec_connector_get_modes().
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Make vc4_vec_encoder_atomic_check() accept arbitrary modelines, as long
as they result in somewhat sane output from the VEC. The bounds have
been determined empirically. Additionally, add support for the
progressive 262-line and 312-line modes.
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
The HVS Gamma block can only be updated when idle, so we need to disable
the HVS channel when the gamma property is set in an atomic commit.
Since the pixelvalve cannot have its assigned channel halted without
stalling unless it's disabled as well, in our case that means forcing a
full disable / enable cycle on the pipeline.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
BCM2711 changes from a 256 entry lookup table to a 16 point
piecewise linear function as the pipeline bitdepth has increased
to make a LUT unwieldy.
Implement a simple conversion from a 256 entry LUT that userspace
is likely to expect to 16 evenly spread points in the PWL. This
could be improved with curve fitting at a later date.
Co-developed-by: Juerg Haefliger <juergh@canonical.com>
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
This is a squash of all firmware-kms related patches from previous
branches, up to and including
"drm/vc4: Set the possible crtcs mask correctly for planes with FKMS"
plus a couple of minor fixups for the 5.9 branch.
Please refer to earlier branches for full history.
This patch includes work by Eric Anholt, James Hughes, Phil Elwell,
Dave Stevenson, Dom Cobley, and Jonathon Bell.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/vc4: Fixup firmware-kms after "drm/atomic: Pass the full state to CRTC atomic enable/disable"
Prototype for those calls changed, so amend fkms (which isn't
upstream) to match.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/vc4: Fixup fkms for API change
Atomic flush and check changed API, so fix up the downstream-only
FKMS driver.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/vc4: Make normalize_zpos conditional on using fkms
Eric's view was that there was no point in having zpos
support on vc4 as all the planes had the same functionality.
Can be later squashed into (and fixes):
drm/vc4: Add firmware-kms mode
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
drm/vc4: FKMS: Change of Broadcast RGB mode needs a mode change
The Broadcast RGB (aka HDMI limited/full range) property is only
notified to the firmware on mode change, so this needs to be
signalled when set.
https://github.com/raspberrypi/firmware/issues/1580
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
vc4/drv: Only notify firmware of display done with kms
fkms driver still wants firmware display to be active
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
ydrm/vc4: fkms: Fix margin calculations for the right/bottom edges
The calculations clipped the right/bottom edge of the clipped
range based on the left/top margins.
https://github.com/raspberrypi/linux/issues/4447
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/vc4: fkms: Use new devm_rpi_firmware_get api
drm/kms: Add allow_fb_modifiers
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Similar to the ch7006 and nouveau drivers, introduce a "tv_mode" module
parameter that allow setting the TV norm by specifying vc4.tv_norm= on
the kernel command line.
If that is not specified, try inferring one of the most popular norms
(PAL or NTSC) from the video mode specified on the command line. On
Raspberry Pis, this causes the most common cases of the sdtv_mode
setting in config.txt to be respected.
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Under FKMS, the firmware (via FKMS) also requires the VideoCore cache
aliases for image planes, as defined by the dma-ranges under /soc.
Add rpi-firmware-kms to the list of acceptable nodes to look for
to copy dma config from.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
[ Upstream commit 0303c9729a ]
Niklāvs reported a boot regression on an Alderlake machine and bisected it
to commit 9df9d2f047 ("init: Invoke arch_cpu_finalize_init() earlier").
By moving the invocation of arch_cpu_finalize_init() further down he
identified that efi_enter_virtual_mode() is the function which causes the
boot hang.
The main difference of the earlier invocation is that the boot CPU is
already fully initialized and mitigations and alternatives are applied.
But the only really interesting change turned out to be IBT, which is now
enabled before efi_enter_virtual_mode(). "ibt=off" on the kernel command
line cured the problem.
Inspection of the involved calls in efi_enter_virtual_mode() unearthed that
efi_set_virtual_address_map() is the only place in the kernel which invokes
an EFI call without the IBT safe wrapper. This went obviously unnoticed so
far as IBT was enabled later.
Use arch_efi_call_virt() instead of efi_call() to cure that.
Fixes: fe379fa4d1 ("x86/ibt: Disable IBT around firmware")
Fixes: 9df9d2f047 ("init: Invoke arch_cpu_finalize_init() earlier")
Reported-by: Niklāvs Koļesņikovs <pinkflames.linux@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217602
Link: https://lore.kernel.org/r/87jzvm12q0.ffs@tglx
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 893b24181b ]
The FFR is a predicate register which can vary between 16 and 256 bits
in size depending upon the configured vector length. When saving the
SVE state in streaming SVE mode, the FFR register is inaccessible and
so commit 9f58486657 ("arm64/sve: Make access to FFR optional") simply
clears the FFR field of the in-memory context structure. Unfortunately,
it achieves this using an unconditional 8-byte store and so if the SME
vector length is anything other than 64 bytes in size we will either
fail to clear the entire field or, worse, we will corrupt memory
immediately following the structure. This has led to intermittent kfence
splats in CI [1] and can trigger kmalloc Redzone corruption messages
when running the 'fp-stress' kselftest:
| =============================================================================
| BUG kmalloc-1k (Not tainted): kmalloc Redzone overwritten
| -----------------------------------------------------------------------------
|
| 0xffff000809bf1e22-0xffff000809bf1e27 @offset=7714. First byte 0x0 instead of 0xcc
| Allocated in do_sme_acc+0x9c/0x220 age=2613 cpu=1 pid=531
| __kmalloc+0x8c/0xcc
| do_sme_acc+0x9c/0x220
| ...
Replace the 8-byte store with a store of a predicate register which has
been zero-initialised with PFALSE, ensuring that the entire field is
cleared in memory.
[1] https://lore.kernel.org/r/CA+G9fYtU7HsV0R0dp4XEH5xXHSJFw8KyDf5VQrLLfMxWfxQkag@mail.gmail.com
Cc: Mark Brown <broonie@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Fixes: 9f58486657 ("arm64/sve: Make access to FFR optional")
Reported-by: Linux Kernel Functional Testing <lkft@linaro.org>
Signed-off-by: Will Deacon <will@kernel.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Link: https://lore.kernel.org/r/20230628155605.22296-1-will@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9cedc58bdb ]
clang warns about a possible field overflow in a memcpy:
In file included from fs/smb/server/smb_common.c:7:
include/linux/fortify-string.h:583:4: error: call to '__write_overflow_field' declared with 'warning' attribute: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror,-Wattribute-warning]
__write_overflow_field(p_size_field, size);
It appears to interpret the "&out[baselen + 4]" as referring to a single
byte of the character array, while the equivalen "out + baselen + 4" is
seen as an offset into the array.
I don't see that kind of warning elsewhere, so just go with the simple
rework.
Fixes: e2f34481b2 ("cifsd: add server-side procedures for SMB3")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ae872de41 ]
When having two DFS root mounts that are connected to same namespace,
same mount options but different prefix paths, we can't really use the
shared @server->origin_fullpath when chasing DFS links in them.
Move the origin_fullpath field to cifs_tcon structure so when having
shared DFS root mounts with different prefix paths, and we need to
chase any DFS links, dfs_get_automount_devname() will pick up the
correct full path out of the @tcon that will be used for the new
mount.
Before patch
mount.cifs //dom/dfs/dir /mnt/1 -o ...
mount.cifs //dom/dfs /mnt/2 -o ...
# shared server, ses, tcon
# server: origin_fullpath=//dom/dfs/dir
# @server->origin_fullpath + '/dir/link1'
$ ls /mnt/2/dir/link1
ls: cannot open directory '/mnt/2/dir/link1': No such file or directory
After patch
mount.cifs //dom/dfs/dir /mnt/1 -o ...
mount.cifs //dom/dfs /mnt/2 -o ...
# shared server & ses
# tcon_1: origin_fullpath=//dom/dfs/dir
# tcon_2: origin_fullpath=//dom/dfs
# @tcon_2->origin_fullpath + '/dir/link1'
$ ls /mnt/2/dir/link1
dir0 dir1 dir10 dir3 dir5 dir6 dir7 dir9 target2_file.txt tsub
Fixes: 8e3554150d ("cifs: fix sharing of DFS connections")
Signed-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 326a8d04f1 ]
All the server credits and in-flight info is protected by req_lock.
Once the req_lock is held, and we've determined that we have enough
credits to continue, this lock cannot be dropped till we've made the
changes to credits and in-flight count.
However, we used to drop the lock in order to avoid deadlock with
the recent srv_lock. This could cause the checks already made to be
invalidated.
Fixed it by moving the server status check to before locking req_lock.
Fixes: d7d7a66aac ("cifs: avoid use of global locks for high contention data")
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 33f736187d ]
In smb2_compound_op we have a possible use-after-free
which can cause hard to debug problems later on.
This was revealed during stress testing with KASAN enabled
kernel. Fixing it by moving the cfile free call to
a few lines below, after the usage.
Fixes: 76894f3e2f ("cifs: improve symlink handling for smb2+")
Reviewed-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e28a798c3 ]
Currently, the EFI stub will disable PCI DMA as the very last thing it
does before calling ExitBootServices(), to avoid interfering with the
firmware's normal operation as much as possible.
However, the stub will invoke DisconnectController() on all endpoints
downstream of the PCI bridges it disables, and this may affect the
layout of the EFI memory map, making it substantially more likely that
ExitBootServices() will fail the first time around, and that the EFI
memory map needs to be reloaded.
This, in turn, increases the likelihood that the slack space we
allocated is insufficient (and we can no longer allocate memory via boot
services after having called ExitBootServices() once), causing the
second call to GetMemoryMap (and therefore the boot) to fail. This makes
the PCI DMA disable feature a bit more fragile than it already is, so
let's make it more robust, by allocating the space for the EFI memory
map after disabling PCI DMA.
Fixes: 4444f8541d ("efi: Allow disabling PCI busmastering on bridges during boot")
Reported-by: Glenn Washburn <development@efficientek.com>
Acked-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1240dabe8d ]
When CONFIG_MODULES is disabled for ARCH=um, 'make (bin)deb-pkg' fails
with an error like follows:
cp: cannot create regular file 'debian/linux-image/usr/lib/uml/modules/6.4.0-rc2+/System.map': No such file or directory
Remove the CONFIG_MODULES check completely so ${pdir}/usr/lib/uml/modules
will always be created and modules.builtin.(modinfo) will be installed
under it for ARCH=um.
Fixes: b611daae5e ("kbuild: deb-pkg: split image and debug objects staging out into functions")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4243afdb93 ]
Even for a non-modular kernel, the kernel builds modules.builtin and
modules.builtin.modinfo, with information about the built-in modules.
Tools such as initramfs-tools need these files to build a working
initramfs on some systems, such as those requiring firmware.
Now that `make modules_install` works even in non-modular kernels and
installs these files, unconditionally invoke it when building a Debian
package.
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Reviewed-by: Nicolas Schier <nicolas@fjasle.eu>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Stable-dep-of: 1240dabe8d ("kbuild: deb-pkg: remove the CONFIG_MODULES check in buildeb")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ab47045ac ]
cxl_region_decode_reset() walks all the decoders associated with a given
region and disables them. Due to decoder ordering rules it is possible
that a switch in the topology notices that a given decoder can not be
shutdown before another region with a higher HPA is shutdown first. That
can leave the region in a partially committed state.
Capture that state in a new CXL_REGION_F_NEEDS_RESET flag and require
that a successful cxl_region_decode_reset() attempt must be completed
before cxl_region_probe() accepts the region.
This is a corollary for the bug that Jonathan identified in "CXL/region
: commit reset of out of order region appears to succeed." [1].
Cc: Jonathan Cameron <Jonathan.Cameron@Huawei.com>
Link: http://lore.kernel.org/r/20230316171441.0000205b@Huawei.com [1]
Fixes: 176baefb2e ("cxl/hdm: Commit decoder state to hardware")
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/168696507423.3590522.16254212607926684429.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1257d098a ]
Vikram raised a concern with the theoretical case of a CPU sending
MemClnEvict to a device that is not prepared to receive. MemClnEvict is
a message that is sent after a CPU has taken ownership of a cacheline
from accelerator memory (HDM-DB). In the case of hotplug or HDM decoder
reconfiguration it is possible that the CPU is holding old contents for
a new device that has taken over the physical address range being cached
by the CPU.
To avoid this scenario, invalidate caches prior to tearing down an HDM
decoder configuration.
Now, this poses another problem that it is possible for something to
speculate into that space while the decode configuration is still up, so
to close that gap also invalidate prior to establish new contents behind
a given physical address range.
With this change the cache invalidation is now explicit and need not be
checked in cxl_region_probe(), and that obviates the need for
CXL_REGION_F_INCOHERENT.
Cc: Jonathan Cameron <Jonathan.Cameron@Huawei.com>
Fixes: d18bc74ace ("cxl/region: Manage CPU caches relative to DPA invalidation events")
Reported-by: Vikram Sethi <vsethi@nvidia.com>
Closes: http://lore.kernel.org/r/BYAPR12MB33364B5EB908BF7239BB996BBD53A@BYAPR12MB3336.namprd12.prod.outlook.com
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/168696506886.3590522.4597053660991916591.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 25a21fbb93 ]
With GCOV_PROFILE_ALL, Clang injects __llvm_gcov_* functions to each
object file, including the *.mod.o. As we filter out CC_FLAGS_CFI
for *.mod.o, the compiler won't generate type hashes for the
injected functions, and therefore indirectly calling them during
module loading trips indirect call checking.
Enabling CFI for *.mod.o isn't sufficient to fix this issue after
commit 0c3e806ec0 ("x86/cfi: Add boot time hash randomization"),
as *.mod.o aren't processed by objtool, which means any hashes
emitted there won't be randomized. Therefore, in addition to
disabling CFI for *.mod.o, also disable GCOV, as the object files
don't otherwise contain any executable code.
Fixes: cf68fffb66 ("add support for Clang CFI")
Reported-by: Joe Fradley <joefradley@google.com>
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ddf56288ee ]
With GCOV_PROFILE_ALL, Clang injects __llvm_gcov_* functions to
each object file, and the functions are indirectly called during
boot. However, when code is injected to object files that are not
part of vmlinux.o, it's also not processed by objtool, which breaks
CFI hash randomization as the hashes in these files won't be
included in the .cfi_sites section and thus won't be randomized.
Similarly to commit 42633ed852 ("kbuild: Fix CFI hash
randomization with KASAN"), disable GCOV for .vmlinux.export.o and
init/version-timestamp.o to avoid emitting unnecessary functions to
object files that don't otherwise have executable code.
Fixes: 0c3e806ec0 ("x86/cfi: Add boot time hash randomization")
Reported-by: Joe Fradley <joefradley@google.com>
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 501e197a02 ]
The st-rng driver uses devres to register itself with the hwrng core,
the driver will be unregistered from hwrng when its device goes out of
scope. This happens after the driver's remove function is called.
However, st-rng's clock is disabled in the remove function. There's a
short timeframe where st-rng is still registered with the hwrng core
although its clock is disabled. I suppose the clock must be active to
access the hardware and serve requests from the hwrng core.
Switch to devm_clk_get_enabled and let devres disable the clock and
unregister the hwrng. This avoids the race condition.
Fixes: 3e75241be8 ("hwrng: drivers - Use device-managed registration API")
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46e66dab85 ]
memory_group_register_static takes maximum number of pages as the argument
while dev_dax_kmem_probe passes total_len (in bytes) as the argument.
IIUC, I don't see any crash/panic impact as such. As,
memory_group_register_static just set the max_pages limit which is used in
auto_movable_zone_for_pfn to determine the zone.
which might cause these condition to behave differently,
This will be true always so jump will happen to kernel_zone
...
if (!auto_movable_can_online_movable(NUMA_NO_NODE, group, nr_pages))
goto kernel_zone;
...
kernel_zone:
return default_kernel_zone_for_pfn(nid, pfn, nr_pages);
Here, In below, zone_intersects compare range will be larger as nr_pages
will be higher (derived from total_len passed in dev_dax_kmem_probe).
...
static struct zone *default_kernel_zone_for_pfn(int nid, unsigned long start_pfn,
unsigned long nr_pages)
{
struct pglist_data *pgdat = NODE_DATA(nid);
int zid;
for (zid = 0; zid < ZONE_NORMAL; zid++) {
struct zone *zone = &pgdat->node_zones[zid];
if (zone_intersects(zone, start_pfn, nr_pages))
return zone;
}
return &pgdat->node_zones[ZONE_NORMAL];
}
Incorrect zone will be returned here, which in later time might cause bigger
problem.
Fixes: eedf634aac ("dax/kmem: use a single static memory group for a single probed unit")
Signed-off-by: Tarun Sahu <tsahu@linux.ibm.com>
Link: https://lore.kernel.org/r/20230621155025.370672-1-tsahu@linux.ibm.com
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d24b170a9 ]
A CONFIG_DEBUG_KOBJECT_RELEASE test of removing a device-dax region
provider (like modprobe -r dax_hmem) yields:
kobject: 'mapping0' (ffff93eb460e8800): kobject_release, parent 0000000000000000 (delayed 2000)
[..]
DEBUG_LOCKS_WARN_ON(1)
WARNING: CPU: 23 PID: 282 at kernel/locking/lockdep.c:232 __lock_acquire+0x9fc/0x2260
[..]
RIP: 0010:__lock_acquire+0x9fc/0x2260
[..]
Call Trace:
<TASK>
[..]
lock_acquire+0xd4/0x2c0
? ida_free+0x62/0x130
_raw_spin_lock_irqsave+0x47/0x70
? ida_free+0x62/0x130
ida_free+0x62/0x130
dax_mapping_release+0x1f/0x30
device_release+0x36/0x90
kobject_delayed_cleanup+0x46/0x150
Due to attempting ida_free() on an ida object that has already been
freed. Devices typically only hold a reference on their parent while
registered. If a child needs a parent object to complete its release it
needs to hold a reference that it drops from its release callback.
Arrange for a dax_mapping to pin its parent dev_dax instance until
dax_mapping_release().
Fixes: 0b07ce872a ("device-dax: introduce 'mapping' devices")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/168577283412.1672036.16111545266174261446.stgit@dwillia2-xfh.jf.intel.com
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da787d5b74 ]
In case if all existing file handles are deferred handles and if all of
them gets closed due to handle lease break then we dont need to send
lease break acknowledgment to server, because last handle close will be
considered as lease break ack.
After closing deferred handels, we check for openfile list of inode,
if its empty then we skip sending lease break ack.
Fixes: 59a556aebc ("SMB3: drop reference to cfile before sending oplock break")
Reviewed-by: Tom Talpey <tom@talpey.com>
Signed-off-by: Bharath SM <bharathsm@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c907e72f58 ]
When the client received NFS4ERR_BADSESSION, it schedules recovery
and start the state manager thread which in turn freezes the
session table and does not allow for any new requests to use the
no-longer valid session. However, it is possible that before
the state manager thread runs, a new operation would use the
released slot that received BADSESSION and was therefore not
updated its sequence number. Such re-use of the slot can lead
the application errors.
Fixes: 5c441544f0 ("NFSv4.x: Handle bad/dead sessions correctly in nfs41_sequence_process()")
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f7ab33689 ]
Currently, the list_lru::shrinker_id corresponding to the nfs4_xattr
shrinkers is wrong:
>>> prog["nfs4_xattr_cache_lru"].shrinker_id
(int)0
>>> prog["nfs4_xattr_entry_lru"].shrinker_id
(int)0
>>> prog["nfs4_xattr_large_entry_lru"].shrinker_id
(int)0
>>> prog["nfs4_xattr_cache_shrinker"].id
(int)18
>>> prog["nfs4_xattr_entry_shrinker"].id
(int)19
>>> prog["nfs4_xattr_large_entry_shrinker"].id
(int)20
This is not what we expect, which will cause these shrinkers
not to be found in shrink_slab_memcg().
We should assign shrinker::id before calling list_lru_init_memcg(),
so that the corresponding list_lru::shrinker_id will be assigned
the correct value like below:
>>> prog["nfs4_xattr_cache_lru"].shrinker_id
(int)16
>>> prog["nfs4_xattr_entry_lru"].shrinker_id
(int)17
>>> prog["nfs4_xattr_large_entry_lru"].shrinker_id
(int)18
>>> prog["nfs4_xattr_cache_shrinker"].id
(int)16
>>> prog["nfs4_xattr_entry_shrinker"].id
(int)17
>>> prog["nfs4_xattr_large_entry_shrinker"].id
(int)18
So just do it.
Fixes: 95ad37f90c ("NFSv4.2: add client side xattr caching.")
Signed-off-by: Qi Zheng <zhengqi.arch@bytedance.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92e2921eea ]
ASM_NL is useful not only in *.S files but also in .c files for using
inline assembler in C code.
On ARC, however, ASM_NL is evaluated inconsistently. It is expanded to
a backquote (`) in *.S files, but a semicolon (;) in *.c files because
arch/arc/include/asm/linkage.h defines it inside #ifdef __ASSEMBLY__,
so the definition for C code falls back to the default value defined in
include/linux/linkage.h.
If ASM_NL is used in inline assembler in .c files, it will result in
wrong assembly code because a semicolon is not an instruction separator,
but the start of a comment for ARC.
Move ASM_NL (also __ALIGN and __ALIGN_STR) out of the #ifdef.
Fixes: 9df62f0544 ("arch: use ASM_NL instead of ';' for assembler new line character in the macro")
Fixes: 8d92e992a7 ("ARC: define __ALIGN_STR and __ALIGN symbols for ARC")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a3f1e573a ]
The > comparison should be >= to prevent an out of bounds array
access.
Fixes: 52dc0595d5 ("modpost: handle relocations mismatch in __ex_table.")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d23659769a ]
With the update of the permanent and intermittent health errors, the
actual indicator for the health test indicates a potential error only
for the one offending time stamp gathered in the current iteration
round. The next iteration round will "overwrite" the health test result.
Thus, the entropy collection loop in jent_gen_entropy checks for
the health test failure upon each loop iteration. However, the
initialization operation checked for the APT health test once for
an APT window which implies it would not catch most errors.
Thus, the check for all health errors is now invoked unconditionally
during each loop iteration for the startup test.
With the change, the error JENT_ERCT becomes unused as all health
errors are only reported with the JENT_HEALTH return code. This
allows the removal of the error indicator.
Fixes: 3fde2fe99a ("crypto: jitter - permanent and intermittent health errors"
)
Reported-by: Joachim Vandersmissen <git@jvdsn.com>
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit efbc7764c4 ]
Commit df8fc4e934 ("kbuild: Enable -fstrict-flex-arrays=3") uncovered
a type mismatch in cesa 3des support that leads to a memcpy beyond the
end of a structure:
In function 'fortify_memcpy_chk',
inlined from 'mv_cesa_des3_ede_setkey' at drivers/crypto/marvell/cesa/cipher.c:307:2:
include/linux/fortify-string.h:583:25: error: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
583 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
This is probably harmless as the actual data that is copied has the correct
type, but clearly worth fixing nonetheless.
Fixes: 4ada483978 ("crypto: marvell/cesa - add Triple-DES support")
Cc: Kees Cook <keescook@chromium.org>
Cc: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56a24b8ce6 ]
addend_arm_rel() processes R_ARM_PC24, R_ARM_CALL, R_ARM_JUMP24 in a
wrong way.
Here, test code.
[test code for R_ARM_JUMP24]
.section .init.text,"ax"
bar:
bx lr
.section .text,"ax"
.globl foo
foo:
b bar
[test code for R_ARM_CALL]
.section .init.text,"ax"
bar:
bx lr
.section .text,"ax"
.globl foo
foo:
push {lr}
bl bar
pop {pc}
If you compile it with ARM multi_v7_defconfig, modpost will show the
symbol name, (unknown).
WARNING: modpost: vmlinux.o: section mismatch in reference: foo (section: .text) -> (unknown) (section: .init.text)
(You need to use GNU linker instead of LLD to reproduce it.)
Fix the code to make modpost show the correct symbol name.
I imported (with adjustment) sign_extend32() from include/linux/bitops.h.
The '+8' is the compensation for pc-relative instruction. It is
documented in "ELF for the Arm Architecture" [1].
"If the relocation is pc-relative then compensation for the PC bias
(the PC value is 8 bytes ahead of the executing instruction in Arm
state and 4 bytes in Thumb state) must be encoded in the relocation
by the object producer."
[1]: https://github.com/ARM-software/abi-aa/blob/main/aaelf32/aaelf32.rst
Fixes: 56a974fa2d ("kbuild: make better section mismatch reports on arm")
Fixes: 6e2e340b59 ("ARM: 7324/1: modpost: Fix section warnings for ARM for many compilers")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7c63520f6 ]
addend_arm_rel() processes R_ARM_ABS32 in a wrong way.
Here, test code.
[test code 1]
#include <linux/init.h>
int __initdata foo;
int get_foo(void) { return foo; }
If you compile it with ARM versatile_defconfig, modpost will show the
symbol name, (unknown).
WARNING: modpost: vmlinux.o: section mismatch in reference: get_foo (section: .text) -> (unknown) (section: .init.data)
(You need to use GNU linker instead of LLD to reproduce it.)
If you compile it for other architectures, modpost will show the correct
symbol name.
WARNING: modpost: vmlinux.o: section mismatch in reference: get_foo (section: .text) -> foo (section: .init.data)
For R_ARM_ABS32, addend_arm_rel() sets r->r_addend to a wrong value.
I just mimicked the code in arch/arm/kernel/module.c.
However, there is more difficulty for ARM.
Here, test code.
[test code 2]
#include <linux/init.h>
int __initdata foo;
int get_foo(void) { return foo; }
int __initdata bar;
int get_bar(void) { return bar; }
With this commit applied, modpost will show the following messages
for ARM versatile_defconfig:
WARNING: modpost: vmlinux.o: section mismatch in reference: get_foo (section: .text) -> foo (section: .init.data)
WARNING: modpost: vmlinux.o: section mismatch in reference: get_bar (section: .text) -> foo (section: .init.data)
The reference from 'get_bar' to 'foo' seems wrong.
I have no solution for this because it is true in assembly level.
In the following output, relocation at 0x1c is no longer associated
with 'bar'. The two relocation entries point to the same symbol, and
the offset to 'bar' is encoded in the instruction 'r0, [r3, #4]'.
Disassembly of section .text:
00000000 <get_foo>:
0: e59f3004 ldr r3, [pc, #4] @ c <get_foo+0xc>
4: e5930000 ldr r0, [r3]
8: e12fff1e bx lr
c: 00000000 .word 0x00000000
00000010 <get_bar>:
10: e59f3004 ldr r3, [pc, #4] @ 1c <get_bar+0xc>
14: e5930004 ldr r0, [r3, #4]
18: e12fff1e bx lr
1c: 00000000 .word 0x00000000
Relocation section '.rel.text' at offset 0x244 contains 2 entries:
Offset Info Type Sym.Value Sym. Name
0000000c 00000c02 R_ARM_ABS32 00000000 .init.data
0000001c 00000c02 R_ARM_ABS32 00000000 .init.data
When find_elf_symbol() gets into a situation where relsym->st_name is
zero, there is no guarantee to get the symbol name as written in C.
I am keeping the current logic because it is useful in many architectures,
but the symbol name is not always correct depending on the optimization.
I left some comments in find_tosym().
Fixes: 56a974fa2d ("kbuild: make better section mismatch reports on arm")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b04b076fb5 ]
Fix build warnings when DEBUG_FS is not enabled by using an empty
do-while loop instead of a value:
In file included from ../drivers/crypto/nx/nx.c:27:
../drivers/crypto/nx/nx.c: In function 'nx_register_algs':
../drivers/crypto/nx/nx.h:173:33: warning: statement with no effect [-Wunused-value]
173 | #define NX_DEBUGFS_INIT(drv) (0)
../drivers/crypto/nx/nx.c:573:9: note: in expansion of macro 'NX_DEBUGFS_INIT'
573 | NX_DEBUGFS_INIT(&nx_driver);
../drivers/crypto/nx/nx.c: In function 'nx_remove':
../drivers/crypto/nx/nx.h:174:33: warning: statement with no effect [-Wunused-value]
174 | #define NX_DEBUGFS_FINI(drv) (0)
../drivers/crypto/nx/nx.c:793:17: note: in expansion of macro 'NX_DEBUGFS_FINI'
793 | NX_DEBUGFS_FINI(&nx_driver);
Also, there is no need to build nx_debugfs.o when DEBUG_FS is not
enabled, so change the Makefile to accommodate that.
Fixes: ae0222b728 ("powerpc/crypto: nx driver code supporting nx encryption")
Fixes: aef7b31c88 ("powerpc/crypto: Build files for the nx device driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Breno Leitão <leitao@debian.org>
Cc: Nayna Jain <nayna@linux.ibm.com>
Cc: Paulo Flabiano Smorigo <pfsmorigo@gmail.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-crypto@vger.kernel.org
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d0acc76a49 ]
find_extable_entry_size() is completely broken. It has awesome comments
about how to calculate sizeof(struct exception_table_entry).
It was based on these assumptions:
- struct exception_table_entry has two fields
- both of the fields have the same size
Then, we came up with this equation:
(offset of the second field) * 2 == (size of struct)
It was true for all architectures when commit 52dc0595d5 ("modpost:
handle relocations mismatch in __ex_table.") was applied.
Our mathematics broke when commit 548acf1923 ("x86/mm: Expand the
exception table logic to allow new handling options") introduced the
third field.
Now, the definition of exception_table_entry is highly arch-dependent.
For x86, sizeof(struct exception_table_entry) is apparently 12, but
find_extable_entry_size() sets extable_entry_size to 8.
I could fix it, but I do not see much value in this code.
extable_entry_size is used just for selecting a slightly different
error message.
If the first field ("insn") references to a non-executable section,
The relocation at %s+0x%lx references
section "%s" which is not executable, IOW
it is not possible for the kernel to fault
at that address. Something is seriously wrong
and should be fixed.
If the second field ("fixup") references to a non-executable section,
The relocation at %s+0x%lx references
section "%s" which is not executable, IOW
the kernel will fault if it ever tries to
jump to it. Something is seriously wrong
and should be fixed.
Merge the two error messages rather than adding even more complexity.
Change fatal() to error() to make it continue running and catch more
possible errors.
Fixes: 548acf1923 ("x86/mm: Expand the exception table logic to allow new handling options")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac52578d6e ]
The virtio rng device kicks off a new entropy request whenever the
data available reaches zero. When a new request occurs at the end
of a read operation, that is, when the result of that request is
only needed by the next reader, then there is a race between the
writing of the new data and the next reader.
This is because there is no synchronisation whatsoever between the
writer and the reader.
Fix this by writing data_avail with smp_store_release and reading
it with smp_load_acquire when we first enter read. The subsequent
reads are safe because they're either protected by the first load
acquire, or by the completion mechanism.
Also remove the redundant zeroing of data_idx in random_recv_done
(data_idx must already be zero at this point) and data_avail in
request_entropy (ditto).
Reported-by: syzbot+726dc8c62c3536431ceb@syzkaller.appspotmail.com
Fixes: f7f510ec19 ("virtio: An entropy device, as suggested by hpa.")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff598081e5 ]
The pointer to mdev_bus_compat_class is statically defined at the top
of mdev_core, and was originally (commit 7b96953bc6 ("vfio: Mediated
device Core driver") serialized by the parent_list_lock. The blamed
commit removed this mutex, leaving the pointer initialization
unserialized. As a result, the creation of multiple MDEVs in parallel
(such as during boot) can encounter errors during the creation of the
sysfs entries, such as:
[ 8.337509] sysfs: cannot create duplicate filename '/class/mdev_bus'
[ 8.337514] vfio_ccw 0.0.01d8: MDEV: Registered
[ 8.337516] CPU: 13 PID: 946 Comm: driverctl Not tainted 6.4.0-rc7 #20
[ 8.337522] Hardware name: IBM 3906 M05 780 (LPAR)
[ 8.337525] Call Trace:
[ 8.337528] [<0000000162b0145a>] dump_stack_lvl+0x62/0x80
[ 8.337540] [<00000001622aeb30>] sysfs_warn_dup+0x78/0x88
[ 8.337549] [<00000001622aeca6>] sysfs_create_dir_ns+0xe6/0xf8
[ 8.337552] [<0000000162b04504>] kobject_add_internal+0xf4/0x340
[ 8.337557] [<0000000162b04d48>] kobject_add+0x78/0xd0
[ 8.337561] [<0000000162b04e0a>] kobject_create_and_add+0x6a/0xb8
[ 8.337565] [<00000001627a110e>] class_compat_register+0x5e/0x90
[ 8.337572] [<000003ff7fd815da>] mdev_register_parent+0x102/0x130 [mdev]
[ 8.337581] [<000003ff7fdc7f2c>] vfio_ccw_sch_probe+0xe4/0x178 [vfio_ccw]
[ 8.337588] [<0000000162a7833c>] css_probe+0x44/0x80
[ 8.337599] [<000000016279f4da>] really_probe+0xd2/0x460
[ 8.337603] [<000000016279fa08>] driver_probe_device+0x40/0xf0
[ 8.337606] [<000000016279fb78>] __device_attach_driver+0xc0/0x140
[ 8.337610] [<000000016279cbe0>] bus_for_each_drv+0x90/0xd8
[ 8.337618] [<00000001627a00b0>] __device_attach+0x110/0x190
[ 8.337621] [<000000016279c7c8>] bus_rescan_devices_helper+0x60/0xb0
[ 8.337626] [<000000016279cd48>] drivers_probe_store+0x48/0x80
[ 8.337632] [<00000001622ac9b0>] kernfs_fop_write_iter+0x138/0x1f0
[ 8.337635] [<00000001621e5e14>] vfs_write+0x1ac/0x2f8
[ 8.337645] [<00000001621e61d8>] ksys_write+0x70/0x100
[ 8.337650] [<0000000162b2bdc4>] __do_syscall+0x1d4/0x200
[ 8.337656] [<0000000162b3c828>] system_call+0x70/0x98
[ 8.337664] kobject: kobject_add_internal failed for mdev_bus with -EEXIST, don't try to register things with the same name in the same directory.
[ 8.337668] kobject: kobject_create_and_add: kobject_add error: -17
[ 8.337674] vfio_ccw: probe of 0.0.01d9 failed with error -12
[ 8.342941] vfio_ccw_mdev aeb9ca91-10c6-42bc-a168-320023570aea: Adding to iommu group 2
Move the initialization of the mdev_bus_compat_class pointer to the
init path, to match the cleanup in module exit. This way the code
in mdev_register_parent() can simply link the new parent to it,
rather than determining whether initialization is required first.
Fixes: 89345d5177 ("vfio/mdev: embedd struct mdev_parent in the parent data structure")
Reported-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Signed-off-by: Eric Farman <farman@linux.ibm.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Tony Krowiak <akrowiak@linux.ibm.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/20230626133642.2939168-1-farman@linux.ibm.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b684c09f09 ]
ppc_save_regs() skips one stack frame while saving the CPU register states.
Instead of saving current R1, it pulls the previous stack frame pointer.
When vmcores caused by direct panic call (such as `echo c >
/proc/sysrq-trigger`), are debugged with gdb, gdb fails to show the
backtrace correctly. On further analysis, it was found that it was because
of mismatch between r1 and NIP.
GDB uses NIP to get current function symbol and uses corresponding debug
info of that function to unwind previous frames, but due to the
mismatching r1 and NIP, the unwinding does not work, and it fails to
unwind to the 2nd frame and hence does not show the backtrace.
GDB backtrace with vmcore of kernel without this patch:
---------
(gdb) bt
#0 0xc0000000002a53e8 in crash_setup_regs (oldregs=<optimized out>,
newregs=0xc000000004f8f8d8) at ./arch/powerpc/include/asm/kexec.h:69
#1 __crash_kexec (regs=<optimized out>) at kernel/kexec_core.c:974
#2 0x0000000000000063 in ?? ()
#3 0xc000000003579320 in ?? ()
---------
Further analysis revealed that the mismatch occurred because
"ppc_save_regs" was saving the previous stack's SP instead of the current
r1. This patch fixes this by storing current r1 in the saved pt_regs.
GDB backtrace with vmcore of patched kernel:
--------
(gdb) bt
#0 0xc0000000002a53e8 in crash_setup_regs (oldregs=0x0, newregs=0xc00000000670b8d8)
at ./arch/powerpc/include/asm/kexec.h:69
#1 __crash_kexec (regs=regs@entry=0x0) at kernel/kexec_core.c:974
#2 0xc000000000168918 in panic (fmt=fmt@entry=0xc000000001654a60 "sysrq triggered crash\n")
at kernel/panic.c:358
#3 0xc000000000b735f8 in sysrq_handle_crash (key=<optimized out>) at drivers/tty/sysrq.c:155
#4 0xc000000000b742cc in __handle_sysrq (key=key@entry=99, check_mask=check_mask@entry=false)
at drivers/tty/sysrq.c:602
#5 0xc000000000b7506c in write_sysrq_trigger (file=<optimized out>, buf=<optimized out>,
count=2, ppos=<optimized out>) at drivers/tty/sysrq.c:1163
#6 0xc00000000069a7bc in pde_write (ppos=<optimized out>, count=<optimized out>,
buf=<optimized out>, file=<optimized out>, pde=0xc00000000362cb40) at fs/proc/inode.c:340
#7 proc_reg_write (file=<optimized out>, buf=<optimized out>, count=<optimized out>,
ppos=<optimized out>) at fs/proc/inode.c:352
#8 0xc0000000005b3bbc in vfs_write (file=file@entry=0xc000000006aa6b00,
buf=buf@entry=0x61f498b4f60 <error: Cannot access memory at address 0x61f498b4f60>,
count=count@entry=2, pos=pos@entry=0xc00000000670bda0) at fs/read_write.c:582
#9 0xc0000000005b4264 in ksys_write (fd=<optimized out>,
buf=0x61f498b4f60 <error: Cannot access memory at address 0x61f498b4f60>, count=2)
at fs/read_write.c:637
#10 0xc00000000002ea2c in system_call_exception (regs=0xc00000000670be80, r0=<optimized out>)
at arch/powerpc/kernel/syscall.c:171
#11 0xc00000000000c270 in system_call_vectored_common ()
at arch/powerpc/kernel/interrupt_64.S:192
--------
Nick adds:
So this now saves regs as though it was an interrupt taken in the
caller, at the instruction after the call to ppc_save_regs, whereas
previously the NIP was there, but R1 came from the caller's caller and
that mismatch is what causes gdb's dwarf unwinder to go haywire.
Signed-off-by: Aditya Gupta <adityag@linux.ibm.com>
Fixes: d16a58f885 ("powerpc: Improve ppc_save_regs()")
Reivewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230615091047.90433-1-adityag@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4f913c980 ]
Currently pointer iov is being dereferenced before the null check of iov
which can lead to null pointer dereference errors. Fix this by moving the
iov null check before the dereferencing.
Detected using cppcheck static analysis:
linux/arch/powerpc/platforms/powernv/pci-sriov.c:597:12: warning: Either
the condition '!iov' is redundant or there is possible null pointer
dereference: iov. [nullPointerRedundantCheck]
num_vfs = iov->num_vfs;
^
Fixes: 052da31d45 ("powerpc/powernv/sriov: De-indent setup and teardown")
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230608095849.1147969-1-colin.i.king@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0fef6bb730 ]
In MCQ mode, when a device command uses a hardware queue shared with other
commands, a race condition may occur in the following scenario:
1. A device command is completed in CQx with CQE entry "e".
2. The interrupt handler copies the "cqe" pointer to "hba->dev_cmd.cqe"
and completes "hba->dev_cmd.complete".
3. The "ufshcd_wait_for_dev_cmd()" function is awakened and retrieves the
OCS value from "hba->dev_cmd.cqe".
However, there is a possibility that the CQE entry "e" will be overwritten
by newly completed commands in CQx, resulting in an incorrect OCS value
being received by "ufshcd_wait_for_dev_cmd()".
To avoid this race condition, the OCS value should be immediately copied to
the struct "lrb" of the device command. Then "ufshcd_wait_for_dev_cmd()"
can retrieve the OCS value from the struct "lrb".
Fixes: 57b1c0ef89 ("scsi: ufs: core: mcq: Add support to allocate multiple queues")
Suggested-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Link: https://lore.kernel.org/r/20230610021553.1213-2-powen.kao@mediatek.com
Tested-by: Po-Wen Kao <powen.kao@mediatek.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3ac3b0779 ]
Test "perf script task-analyzer tests" fails in environment with missing
libtraceevent support, as perf record fails to create the perf.data
file, which further tests depend on.
Instead, when perf is not compiled with libtraceevent support, skip
those tests instead of failing them, by checking the output of `perf
record --dry-run` to see if it prints the error "libtraceevent is
necessary for tracepoint support"
For the following output, perf compiled with: `make NO_LIBTRACEEVENT=1`
Before the patch:
108: perf script task-analyzer tests :
test child forked, pid 24105
failed to open perf.data: No such file or directory (try 'perf record' first)
FAIL: "invokation of perf script report task-analyzer command failed" Error message: ""
FAIL: "test_basic" Error message: "Failed to find required string:'Comm'."
failed to open perf.data: No such file or directory (try 'perf record' first)
FAIL: "invokation of perf script report task-analyzer --ns --rename-comms-by-tids 0:random command failed" Error message: ""
FAIL: "test_ns_rename" Error message: "Failed to find required string:'Comm'."
failed to open perf.data: No such file or directory (try 'perf record' first)
<...>
perf script task-analyzer tests: FAILED!
With this patch, the script instead returns 2 signifying SKIP, and after
the patch:
108: perf script task-analyzer tests :
test child forked, pid 26010
libtraceevent is necessary for tracepoint support
WARN: Skipping tests. No libtraceevent support
test child finished with -2
perf script task-analyzer tests: Skip
Fixes: e8478b84d6 ("perf test: Add new task-analyzer tests")
Signed-off-by: Aditya Gupta <adityag@linux.ibm.com>
Cc: Disha Goel <disgoel@linux.vnet.ibm.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: John Garry <john.g.garry@oracle.com>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Petar Gligoric <petar.gligoric@rohde-schwarz.com>
Cc: Ravi Bangoria <ravi.bangoria@amd.com>
Cc: linuxppc-dev@lists.ozlabs.org
Link: https://lore.kernel.org/r/20230613164145.50488-18-atrajeev@linux.vnet.ibm.com
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f999e23ce6 ]
Fix issues identified in dytc_profile_refresh identified by lkp-tests.
drivers/platform/x86/thinkpad_acpi.c:10538
dytc_profile_refresh() error: uninitialized symbol 'funcmode'.
drivers/platform/x86/thinkpad_acpi.c:10531
dytc_profile_refresh() error: uninitialized symbol 'output'.
drivers/platform/x86/thinkpad_acpi.c:10537
dytc_profile_refresh() error: uninitialized symbol 'output'.
These issues should not lead to real problems in the field as the refresh
function should only be called if MMC or PSC mode enabled. But good to fix.
Thanks to Dan Carpenter and the lkp-tests project for flagging these.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Closes: https://lore.kernel.org/r/202306011202.1hbgLRD4-lkp@intel.com/
Fixes: 1bc5d819f0 ("platform/x86: thinkpad_acpi: Fix profile modes on Intel platforms")
Signed-off-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Link: https://lore.kernel.org/r/20230606151804.8819-1-mpearson-lenovo@squebb.ca
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36d3e4138e ]
When printing output we may want to generate per event files, where the
--per-event-dump option should be used, creating perf.data.EVENT.dump
files instead of printing to stdout.
The callback thar processes event thus expects that evsel->priv->fp
should point to either the per-event FILE descriptor or to stdout.
The a3af66f51b ("perf script: Fix crash because of missing
evsel->priv") changeset fixed a case where evsel->priv wasn't setup,
thus set to NULL, causing a segfault when trying to access
evsel->priv->fp.
But it did it for the non --per-event-dump case by allocating a 'struct
perf_evsel_script' just to set its ->fp to stdout.
Since evsel->priv is only freed when --per-event-dump is used, we ended
up with a memory leak, detected using ASAN.
Fix it by using the same method as perf_script__setup_per_event_dump(),
and reuse that static 'struct perf_evsel_script'.
Also check if evsel_script__new() failed.
Fixes: a3af66f51b ("perf script: Fix crash because of missing evsel->priv")
Reported-by: Ian Rogers <irogers@google.com>
Tested-by: Ian Rogers <irogers@google.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Link: https://lore.kernel.org/lkml/ZH+F0wGAWV14zvMP@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a03b1a0b19 ]
Looking at generated code for handle_signal32() shows calls to a
function called __unsafe_save_user_regs.constprop.0 while user access
is open.
And that __unsafe_save_user_regs.constprop.0 function has two nops at
the begining, allowing it to be traced, which is unexpected during
user access open window.
The solution could be to mark __unsafe_save_user_regs() no trace, but
to be on the safe side the most efficient is to flag it __always_inline
as already done for function __unsafe_restore_general_regs(). The
function is relatively small and only called twice, so the size
increase will remain in the noise.
Do the same with save_tm_user_regs_unsafe() as it may suffer the
same issue.
Fixes: ef75e73182 ("powerpc/signal32: Transform save_user_regs() and save_tm_user_regs() in 'unsafe' version")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/7e469c8f01860a69c1ada3ca6a5e2aa65f0f74b2.1685955220.git.christophe.leroy@csgroup.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0eb089a72f ]
A disassembly of interrupt_exit_kernel_prepare() shows a useless read
of MSR register. This is shown by r9 being re-used immediately without
doing anything with the value read.
c000e0e0: 60 00 00 00 nop
c000e0e4: 7d 3a c2 a6 mfmd_ap r9
c000e0e8: 7d 20 00 a6 mfmsr r9
c000e0ec: 7c 51 13 a6 mtspr 81,r2
c000e0f0: 81 3f 00 84 lwz r9,132(r31)
c000e0f4: 71 29 80 00 andi. r9,r9,32768
This is due to the use of local_irq_save(). The flags read by
local_irq_save() are never used, use local_irq_disable() instead.
Fixes: 13799748b9 ("powerpc/64: use interrupt restart table to speed up return from interrupt")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/df36c6205ab64326fb1b991993c82057e92ace2f.1685955214.git.christophe.leroy@csgroup.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 353e7300a1 ]
Activating KCSAN on a 32 bits architecture leads to the following
link-time failure:
LD .tmp_vmlinux.kallsyms1
powerpc64-linux-ld: kernel/kcsan/core.o: in function `__tsan_atomic64_load':
kernel/kcsan/core.c:1273: undefined reference to `__atomic_load_8'
powerpc64-linux-ld: kernel/kcsan/core.o: in function `__tsan_atomic64_store':
kernel/kcsan/core.c:1273: undefined reference to `__atomic_store_8'
powerpc64-linux-ld: kernel/kcsan/core.o: in function `__tsan_atomic64_exchange':
kernel/kcsan/core.c:1273: undefined reference to `__atomic_exchange_8'
powerpc64-linux-ld: kernel/kcsan/core.o: in function `__tsan_atomic64_fetch_add':
kernel/kcsan/core.c:1273: undefined reference to `__atomic_fetch_add_8'
powerpc64-linux-ld: kernel/kcsan/core.o: in function `__tsan_atomic64_fetch_sub':
kernel/kcsan/core.c:1273: undefined reference to `__atomic_fetch_sub_8'
powerpc64-linux-ld: kernel/kcsan/core.o: in function `__tsan_atomic64_fetch_and':
kernel/kcsan/core.c:1273: undefined reference to `__atomic_fetch_and_8'
powerpc64-linux-ld: kernel/kcsan/core.o: in function `__tsan_atomic64_fetch_or':
kernel/kcsan/core.c:1273: undefined reference to `__atomic_fetch_or_8'
powerpc64-linux-ld: kernel/kcsan/core.o: in function `__tsan_atomic64_fetch_xor':
kernel/kcsan/core.c:1273: undefined reference to `__atomic_fetch_xor_8'
powerpc64-linux-ld: kernel/kcsan/core.o: in function `__tsan_atomic64_fetch_nand':
kernel/kcsan/core.c:1273: undefined reference to `__atomic_fetch_nand_8'
powerpc64-linux-ld: kernel/kcsan/core.o: in function `__tsan_atomic64_compare_exchange_strong':
kernel/kcsan/core.c:1273: undefined reference to `__atomic_compare_exchange_8'
powerpc64-linux-ld: kernel/kcsan/core.o: in function `__tsan_atomic64_compare_exchange_weak':
kernel/kcsan/core.c:1273: undefined reference to `__atomic_compare_exchange_8'
powerpc64-linux-ld: kernel/kcsan/core.o: in function `__tsan_atomic64_compare_exchange_val':
kernel/kcsan/core.c:1273: undefined reference to `__atomic_compare_exchange_8'
32 bits architectures don't have 64 bits atomic builtins. Only
include DEFINE_TSAN_ATOMIC_OPS(64) on 64 bits architectures.
Fixes: 0f8ad5f2e9 ("kcsan: Add support for atomic builtins")
Suggested-by: Marco Elver <elver@google.com>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Marco Elver <elver@google.com>
Acked-by: Marco Elver <elver@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/d9c6afc28d0855240171a4e0ad9ffcdb9d07fceb.1683892665.git.christophe.leroy@csgroup.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 416a87c972 ]
commit c5ad454a12 ("platform/x86: intel/pmc/core: Add Meteor Lake
support to pmc core driver") was supposed to add support for Meter
Lake P/M and mistakenly added support for Meteor Lake S instead. Meteor
Lake P/M support was added later and MTL-S support needs to be removed
since its currently assigned to the wrong register maps.
Fixes: c5ad454a12 ("platform/x86: intel/pmc/core: Add Meteor Lake support to pmc core driver")
Signed-off-by: Xi Pardee <xi.pardee@intel.com>
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Link: https://lore.kernel.org/r/20230601004706.871528-1-xi.pardee@intel.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5835196a17 ]
Currently the getter returns ENOTSUPP on pin configured in
the push-pull mode. Fix this by adding the missed switch case.
Fixes: ccdf81d08d ("pinctrl: cherryview: add option to set open-drain pin config")
Fixes: 6e08d6bbeb ("pinctrl: Add Intel Cherryview/Braswell pin controller support")
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fad5723350 ]
The function table is filled with group information based on other
instance-specific data at runtime. However, the function table can be
shared between multiple instances, causing the ->probe() function for
one instance to overwrite the table of a previously probed instance.
Fix this by sharing only the function names and allocating a separate
function table for each instance.
Fixes: 5a00473607 ("pinctrl: tegra: Separate Tegra194 instances")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20230530105308.1292852-1-thierry.reding@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 549e91a9bb ]
ufshcd_queuecommand() may be called two times in a row for a SCSI command
before it is completed. Hence make the following changes:
- In the functions that submit a command, do not check the old value of
lrbp->cmd nor clear lrbp->cmd in error paths.
- In ufshcd_release_scsi_cmd(), do not clear lrbp->cmd.
See also scsi_send_eh_cmnd().
This commit prevents that the following appears if a command times out:
WARNING: at drivers/ufs/core/ufshcd.c:2965 ufshcd_queuecommand+0x6f8/0x9a8
Call trace:
ufshcd_queuecommand+0x6f8/0x9a8
scsi_send_eh_cmnd+0x2c0/0x960
scsi_eh_test_devices+0x100/0x314
scsi_eh_ready_devs+0xd90/0x114c
scsi_error_handler+0x2b4/0xb70
kthread+0x16c/0x1e0
Fixes: 5a0b0cb9be ("[SCSI] ufs: Add support for sending NOP OUT UPIU")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20230524203659.1394307-3-bvanassche@acm.org
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe8637f770 ]
One UFS vendor asked to increase the UFS timeout from 1 s to 3 s. Another
UFS vendor asked to increase the UFS timeout from 1 s to 10 s. Hence this
patch that increases the UFS timeout to 10 s. This patch can cause the
total timeout to exceed 20 s, the Android shutdown timeout. This is fine
since the loop around ufshcd_execute_start_stop() exists to deal with unit
attentions and because unit attentions are reported quickly.
Fixes: dcd5b7637c ("scsi: ufs: Reduce the START STOP UNIT timeout")
Fixes: 8f2c96420c ("scsi: ufs: core: Reduce the power mode change timeout")
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20230524203659.1394307-2-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9914a3d033 ]
When NPIV ports are zoned to devices that support both initiator and target
mode, a remote device's initiated PRLI results in unintended final kref
clean up of the device's ndlp structure. This disrupts NPIV ports'
discovery for target devices that support both initiator and target mode.
Modify the NPIV lpfc_drop_node clause such that we allow the ndlp to live
so long as it was in NLP_STE_PLOGI_ISSUE, NLP_STE_REG_LOGIN_ISSUE, or
NLP_STE_PRLI_ISSUE nlp_state. This allows lpfc's issued PRLI completion
routine to determine if the final kref clean up should execute rather than
a remote device's issued PRLI.
Fixes: db651ec225 ("scsi: lpfc: Correct used_rpi count when devloss tmo fires with no recovery")
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20230523183206.7728-5-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c60738de85 ]
Smatch reported:
1. drivers/pci/controller/pci-ftpci100.c:526 faraday_pci_probe() warn:
'clk' from clk_prepare_enable() not released on lines: 442,451,462,478,512,517.
2. drivers/pci/controller/pci-ftpci100.c:526 faraday_pci_probe() warn:
'p->bus_clk' from clk_prepare_enable() not released on lines: 451,462,478,512,517.
The clock resource is obtained by devm_clk_get(), and then
clk_prepare_enable() makes the clock resource ready for use. After that,
clk_disable_unprepare() should be called to release the clock resource
when it is no longer needed. However, while doing some error handling
in faraday_pci_probe(), clk_disable_unprepare() is not called to release
clk and p->bus_clk before returning. These return lines are exactly 442,
451, 462, 478, 512, 517.
Fix this warning by replacing devm_clk_get() with devm_clk_get_enabled(),
which is equivalent to devm_clk_get() + clk_prepare_enable(). And with
devm_clk_get_enabled(), the clock will automatically be disabled,
unprepared and freed when the device is unbound from the bus.
Link: https://lore.kernel.org/r/20230508043641.23807-1-yejunyan@hust.edu.cn
Fixes: b3c433efb8 ("PCI: faraday: Fix wrong pointer passed to PTR_ERR()")
Fixes: 2eeb02b285 ("PCI: faraday: Add clock handling")
Fixes: 783a862563 ("PCI: faraday: Use pci_parse_request_of_pci_ranges()")
Fixes: d3c68e0a7e ("PCI: faraday: Add Faraday Technology FTPCI100 PCI Host Bridge driver")
Fixes: f1e8bd21e3 ("PCI: faraday: Convert IRQ masking to raw PCI config accessors")
Signed-off-by: Junyan Ye <yejunyan@hust.edu.cn>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8afd0d9fc ]
If a PCIe hotplug slot has an Attention Button, the normal hot-add flow is:
- Slot is empty and slot power is off
- User inserts card in slot and presses Attention Button
- OS blinks Power Indicator for 5 seconds
- After 5 seconds, OS turns on Power Indicator, turns on slot power, and
enumerates the device
Previously, if a user pressed the Attention Button on an *empty* slot,
pciehp logged the following messages and blinked the Power Indicator
until a second button press:
[0.000] pciehp: Button press: will power on in 5 sec
[0.001] # Power Indicator starts blinking
[5.001] # 5 second timeout; slot is empty, so we should cancel the
request to power on and turn off Power Indicator
[7.000] # Power Indicator still blinking
[8.000] # possible card insertion
[9.000] pciehp: Button press: canceling request to power on
The first button press incorrectly left the slot in BLINKINGON_STATE, so
the second was interpreted as a "cancel power on" event regardless of
whether a card was present.
If the slot is empty, turn off the Power Indicator and return from
BLINKINGON_STATE to OFF_STATE after 5 seconds, effectively canceling the
request to power on. Putting the slot in OFF_STATE also means the second
button press will correctly request a slot power on if the slot is
occupied.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20230512021518.336460-1-clementwei90@163.com
Fixes: d331710ea7 ("PCI: pciehp: Become resilient to missed events")
Suggested-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Rongguang Wei <weirongguang@kylinos.cn>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 456d8aa37d ]
Struct pcie_link_state->downstream is a pointer to the pci_dev of function
0. Previously we retained that pointer when removing function 0, and
subsequent ASPM policy changes dereferenced it, resulting in a
use-after-free warning from KASAN, e.g.:
# echo 1 > /sys/bus/pci/devices/0000:03:00.0/remove
# echo powersave > /sys/module/pcie_aspm/parameters/policy
BUG: KASAN: slab-use-after-free in pcie_config_aspm_link+0x42d/0x500
Call Trace:
kasan_report+0xae/0xe0
pcie_config_aspm_link+0x42d/0x500
pcie_aspm_set_policy+0x8e/0x1a0
param_attr_store+0x162/0x2c0
module_attr_store+0x3e/0x80
PCIe spec r6.0, sec 7.5.3.7, recommends that software program the same ASPM
Control value in all functions of multi-function devices.
Disable ASPM and free the pcie_link_state when any child function is
removed so we can discard the dangling pcie_link_state->downstream pointer
and maintain the same ASPM Control configuration for all functions.
[bhelgaas: commit log and comment]
Debugged-by: Zongquan Qin <qinzongquan@sangfor.com.cn>
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Fixes: b5a0a9b59c ("PCI/ASPM: Read and set up L1 substate capabilities")
Link: https://lore.kernel.org/r/20230507034057.20970-1-dinghui@sangfor.com.cn
Signed-off-by: Ding Hui <dinghui@sangfor.com.cn>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 711bcc0cb3 ]
Ensure that both the keyboard touchscreen and the digitizer have their
driver bound after remove(). Without this modprobing lenovo-yogabook-wmi
after a rmmod fails because lenovo-yogabook-wmi defers probing until
both devices have their driver bound.
Fixes: c0549b72d9 ("platform/x86: lenovo-yogabook-wmi: Add driver for Lenovo Yoga Book")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230430165807.472798-4-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9148cd2eb4 ]
When yogabook_wmi_remove() runs yogabook_wmi_work might still be running
and using the devices which yogabook_wmi_remove() puts.
To avoid this move to explicitly cancelling the work rather then using
devm_work_autocancel().
This requires also making the yogabook_backside_hall_irq handler non
devm managed, so that it cannot re-queue the work while
yogabook_wmi_remove() runs.
Fixes: c0549b72d9 ("platform/x86: lenovo-yogabook-wmi: Add driver for Lenovo Yoga Book")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230430165807.472798-3-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f025312b08 ]
Smatch reported:
drivers/scsi/qedf/qedf_main.c:3056 qedf_alloc_global_queues()
warn: missing unwind goto?
At this point in the function, nothing has been allocated so we can return
directly. In particular the "qedf->global_queues" have not been allocated
so calling qedf_free_global_queues() will lead to a NULL dereference when
we check if (!gl[i]) and "gl" is NULL.
Fixes: 61d8658b4a ("scsi: qedf: Add QLogic FastLinQ offload FCoE driver framework.")
Signed-off-by: Jinhong Zhu <jinhongzhu@hust.edu.cn>
Link: https://lore.kernel.org/r/20230502140022.2852-1-jinhongzhu@hust.edu.cn
Reviewed-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b61cf04c49 ]
VMD driver can disable or enable MSI remapping by changing
VMCONFIG_MSI_REMAP register. This register needs to be set to the
default value during soft reboots. Drives failed to enumerate
when Windows boots after performing a soft reboot from Linux.
Windows doesn't support MSI remapping disable feature and stale
register value hinders Windows VMD driver initialization process.
Adding vmd_shutdown function to make sure to set the VMCONFIG
register to the default value.
Link: https://lore.kernel.org/r/20230224202811.644370-1-nirmal.patel@linux.intel.com
Fixes: ee81ee84f8 ("PCI: vmd: Disable MSI-X remapping when possible")
Signed-off-by: Nirmal Patel <nirmal.patel@linux.intel.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Jon Derrick <jonathan.derrick@linux.dev>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e12f83023 ]
The Link Retraining process is initiated to account for the Gen2 defect in
the Cadence PCIe controller in J721E SoC. The errata corresponding to this
is i2085, documented at:
https://www.ti.com/lit/er/sprz455c/sprz455c.pdf
The existing workaround implemented for the errata waits for the Data Link
initialization to complete and assumes that the link retraining process
at the Physical Layer has completed. However, it is possible that the
Physical Layer training might be ongoing as indicated by the
PCI_EXP_LNKSTA_LT bit in the PCI_EXP_LNKSTA register.
Fix the existing workaround, to ensure that the Physical Layer training
has also completed, in addition to the Data Link initialization.
Link: https://lore.kernel.org/r/20230315070800.1615527-1-s-vadapalli@ti.com
Fixes: 4740b969aa ("PCI: cadence: Retrain Link to work around Gen2 training defect")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b07d5cc93e ]
After copy up, we may need to update d_flags if upper dentry is on a
remote fs and lower dentries are not.
Add helpers to allow incremental update of the revalidate flags.
Fixes: bccece1ead ("ovl: allow remote upper")
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2560114c06 ]
In case devm_clk_hw_register() fails for one of synth clocks the probe
continues. Later on, when registering output clocks which have as parents
all the synth clocks, in case there is registration failure for at least
one synth clock the information passed to clk core for registering output
clock is not right: init.num_parents is fixed but init.parents may contain
an array with less parents.
Fixes: 3044a860fd ("clk: Add Si5341/Si5340 driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230530093913.1656095-4-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71344a718a ]
The fixed commit listed in the Fixes tag below, introduced a bug in
amdgpu_ras.c::amdgpu_reserve_page_direct(), in that when introducing the new
amdgpu_umc_fill_error_record() and internally in that new function the physical
address (argument "uint64_t retired_page"--wrong name) is right-shifted by
AMDGPU_GPU_PAGE_SHIFT. Thus, in amdgpu_reserve_page_direct() when we pass
"address" to that new function, we should NOT right-shift it, since this
results, erroneously, in the page address to be 0 for first
2^(2*AMDGPU_GPU_PAGE_SHIFT) memory addresses.
This commit fixes this bug.
Cc: Tao Zhou <tao.zhou1@amd.com>
Cc: Hawking Zhang <Hawking.Zhang@amd.com>
Cc: Alex Deucher <Alexander.Deucher@amd.com>
Fixes: 400013b268 ("drm/amdgpu: add umc_fill_error_record to make code more simple")
Signed-off-by: Luben Tuikov <luben.tuikov@amd.com>
Link: https://lore.kernel.org/r/20230610113536.10621-1-luben.tuikov@amd.com
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d50dc746ff ]
Fixes the following gcc with W=1:
In file included from ./include/linux/string.h:253,
from ./include/linux/bitmap.h:11,
from ./include/linux/cpumask.h:12,
from ./arch/x86/include/asm/cpumask.h:5,
from ./arch/x86/include/asm/msr.h:11,
from ./arch/x86/include/asm/processor.h:22,
from ./arch/x86/include/asm/cpufeature.h:5,
from ./arch/x86/include/asm/thread_info.h:53,
from ./include/linux/thread_info.h:60,
from ./arch/x86/include/asm/preempt.h:7,
from ./include/linux/preempt.h:78,
from ./include/linux/spinlock.h:56,
from ./include/linux/mmzone.h:8,
from ./include/linux/gfp.h:7,
from ./include/linux/firmware.h:7,
from drivers/gpu/drm/amd/amdgpu/../pm/swsmu/smu11/sienna_cichlid_ppt.c:26:
In function ‘fortify_memcpy_chk’,
inlined from ‘sienna_cichlid_append_powerplay_table’ at drivers/gpu/drm/amd/amdgpu/../pm/swsmu/smu11/sienna_cichlid_ppt.c:444:2,
inlined from ‘sienna_cichlid_setup_pptable’ at drivers/gpu/drm/amd/amdgpu/../pm/swsmu/smu11/sienna_cichlid_ppt.c:506:8,
inlined from ‘sienna_cichlid_setup_pptable’ at drivers/gpu/drm/amd/amdgpu/../pm/swsmu/smu11/sienna_cichlid_ppt.c:494:12:
./include/linux/fortify-string.h:413:4: warning: call to ‘__read_overflow2_field’ declared with attribute warning: detected read beyond size of field (2nd parameter); maybe use struct_group()? [-Wattribute-warning]
413 | __read_overflow2_field(q_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
the compiler complains about the size calculation in the memcpy() -
"sizeof(*smc_dpm_table) - sizeof(smc_dpm_table->table_header)" is much
larger than what fits into table_member.
Hence, reuse 'smu_memcpy_trailing' for nv1x
Fixes: 7077b19a38 ("drm/amd/pm: use macro to get pptable members")
Suggested-by: Evan Quan <Evan.Quan@amd.com>
Cc: Evan Quan <Evan.Quan@amd.com>
Cc: Chengming Gui <Jack.Gui@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3bfbff9b46 ]
The bootrom burned into the MT7986 SoC will try multiple locations on
the SPI-NAND flash to load bl2 in case the bl2 image located at the the
previously attempted offset is corrupt.
Use 0x100000 instead of 0x80000 as partition size for bl2 on SPI-NAND,
allowing for up to four redundant copies of bl2 (typically sized a
bit less than 0x40000).
Fixes: 8e01fb15b8 ("arm64: dts: mt7986: add Bananapi R3")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/ZH9UGF99RgzrHZ88@makrotopia.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a4366b5695 ]
The capacity-dmips-mhz parameter was miscalculated: this SoC runs
the first (Cortex-A55) cluster at a maximum of 2000MHz and the
second (Cortex-A76) cluster at a maximum of 2200MHz.
In order to calculate the right capacity-dmips-mhz, the following
test was performed:
1. CPUFREQ governor was set to 'performance' on both clusters
2. Ran dhrystone with 500000000 iterations for 10 times on each cluster
3. Calculated the mean result for each cluster
4. Calculated DMIPS/MHz: dmips_mhz = dmips_per_second / cpu_mhz
5. Scaled results to 1024:
result_c0 = dmips_mhz_c0 / dmips_mhz_c1 * 1024
The mean results for this SoC are:
Cluster 0 (LITTLE): 12016411 Dhry/s
Cluster 1 (BIG): 31702034 Dhry/s
The calculated scaled results are:
Cluster 0: 426.953226899238 (rounded to 427)
Cluster 1: 1024
Fixes: 48489980e2 ("arm64: dts: Add Mediatek SoC MT8192 and evaluation board dts and Makefile")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230602183515.3778780-1-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7bfb2ad21 ]
Using devres to depopulate the aux bus made sure that upon a probe
deferral the EDP panel device would be destroyed and recreated upon next
attempt.
But the struct device which the devres is tied to is the DPUs
(drm_dev->dev), which may be happen after the DP controller is torn
down.
Indications of this can be seen in the commonly seen EDID-hexdump full
of zeros in the log, or the occasional/rare KASAN fault where the
panel's attempt to read the EDID information causes a use after free on
DP resources.
It's tempting to move the devres to the DP controller's struct device,
but the resources used by the device(s) on the aux bus are explicitly
torn down in the error path. The KASAN-reported use-after-free also
remains, as the DP aux "module" explicitly frees its devres-allocated
memory in this code path.
As such, explicitly depopulate the aux bus in the error path, and in the
component unbind path, to avoid these issues.
Fixes: 2b57f72661 ("drm/msm/dp: fix aux-bus EP lifetime")
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/542163/
Link: https://lore.kernel.org/r/20230612220106.1884039-1-quic_bjorande@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 155fa3a91d ]
Currently, slice_count is being used to calculate word count and
pkt_per_line. Instead, these values should be calculated using slice per
packet, which is not the same as slice_count.
Slice count represents the number of slices per interface, and its value
will not always match that of slice per packet. For example, it is possible
to have cases where there are multiple slices per interface but the panel
specifies only one slice per packet.
Thus, use the default value of one slice per packet and remove slice_count
from the aforementioned calculations.
Fixes: 08802f515c ("drm/msm/dsi: Add support for DSC configuration")
Fixes: bc6b6ff813 ("drm/msm/dsi: Use DSC slice(s) packet size to compute word count")
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/541965/
Link: https://lore.kernel.org/r/20230405-add-dsc-support-v6-5-95eab864d1b6@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b38c6ced4e ]
main_i2c0 is aliased as i2c0 which creates a problem for u-boot R5
SPL attempting to reuse the same definition in the common board
detection logic as it looks for the first i2c instance as the bus on
which to detect the eeprom to understand the board variant involved.
Switch main_i2c0 to i2c3 alias allowing us to introduce wkup_i2c0
and potentially space for mcu_i2c instances in the gap for follow on
patches.
Fixes: 635fb18ba0 ("arch: arm64: dts: Add support for AM69 Starter Kit")
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20230602214937.2349545-5-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c10a9df30e ]
main_i2c0 is aliased as i2c0 which creates a problem for u-boot R5
SPL attempting to reuse the same definition in the common board
detection logic as it looks for the first i2c instance as the bus on
which to detect the eeprom to understand the board variant involved.
Switch main_i2c0 to i2c3 alias allowing us to introduce wkup_i2c0
and potentially space for mcu_i2c instances in the gap for follow on
patches.
Fixes: e20a06aca5 ("arm64: dts: ti: Add support for J784S4 EVM board")
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20230602214937.2349545-2-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 155e7635ed ]
Mailbox nodes are now disabled by default. The BeagleBoard AI64 DT
addition went in at around the same time and must have missed that
change so the mailboxes are not re-enabled. Do that here.
Fixes: fae14a1cb8 ("arm64: dts: ti: Add k3-j721e-beagleboneai64")
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230515172137.474626-1-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 223ce29c8b ]
The framebuffer configuration for edo pdx203, written in edo dtsi (which
is overwritten in pdx206 dts for its smaller panel) has to use a
1096x2560 configuration as this is what the panel (and framebuffer area)
has been initialized to. Downstream userspace also has access to (and
uses) this 2.5k mode by default, and only switches the panel to 4k when
requested.
This is similar to commit be8de06dc3 ("arm64: dts: qcom:
sm8150-kumano: Panel framebuffer is 2.5k instead of 4k") which fixed the
same for the previous generation Sony platform.
Fixes: 69cdb97ef6 ("arm64: dts: qcom: sm8250: Add support for SONY Xperia 1 II / 5 II (Edo platform)")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230606211418.587676-1-marijn.suijten@somainline.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b04cbd81b ]
The rpmh driver will cache sleep and wake votes until the cluster
power-domain is about to enter idle, to avoid unnecessary writes. So
associate the apps_rsc with the cluster pd, so that it can be notified
about this event.
Without this, only AMC votes are being commited.
Fixes: 07c8ded6e3 ("arm64: dts: qcom: add sdm670 and pixel 3a device trees")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230531-topic-rsc-v1-5-b4a985f57b8b@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3db7285e04 ]
Smatch reports:
drivers/clk/mediatek/clk-mtk.c:583 mtk_clk_simple_probe() warn:
'base' from of_iomap() not released on lines: 496.
This problem was also found in linux-next. In mtk_clk_simple_probe(),
base is not released when handling errors
if clk_data is not existed, which may cause a leak.
So free_base should be added here to release base.
Fixes: c58cd0e40f ("clk: mediatek: Add mtk_clk_simple_probe() to simplify clock providers")
Signed-off-by: Bosi Zhang <u201911157@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/r/20230422084331.47198-1-u201911157@hust.edu.cn
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 878b02d5f3 ]
Replace of_iomap() and kzalloc() with devm_of_iomap() and devm_kzalloc()
which can automatically release the related memory when the device
or driver is removed or unloaded to avoid potential memory leak.
In this case, iounmap(anatop_base) in line 427,433 are removed
as manual release is not required.
Besides, referring to clk-imx8mq.c, check the return code of
of_clk_add_hw_provider, if it returns negtive, print error info
and unregister hws, which makes the program more robust.
Fixes: 9c140d9926 ("clk: imx: Add support for i.MX8MP clock driver")
Signed-off-by: Yuxing Liu <lyx2022@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20230503070607.2462-1-lyx2022@hust.edu.cn
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e02ba11b45 ]
In function probe(), it returns directly without unregistered hws
when error occurs.
Fix this by adding 'goto unregister_hws;' on line 295 and
line 310.
Use devm_kzalloc() instead of kzalloc() to automatically
free the memory using devm_kfree() when error occurs.
Replace of_iomap() with devm_of_iomap() to automatically
handle the unused ioremap region and delete 'iounmap(anatop_base);'
in unregister_hws.
Fixes: 24defbe194 ("clk: imx: add i.MX93 clk")
Signed-off-by: Zhanhao Hu <zero12113@hust.edu.cn>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20230601033825.336558-1-zero12113@hust.edu.cn
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b280598ab ]
Use devm_of_iomap() instead of of_iomap() to automatically
handle the unused ioremap region. If any error occurs, regions allocated by
kzalloc() will leak, but using devm_kzalloc() instead will automatically
free the memory using devm_kfree().
Also, fix error handling of hws by adding unregister_hws label, which
unregisters remaining hws when iomap failed.
Fixes: 7154b046d8 ("clk: imx: Add initial support for i.MXRT1050 clock driver")
Signed-off-by: Kai Ma <kaima@hust.edu.cn>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Jesse Taube <Mr.Bossman075@gmail.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20230418113451.151312-1-kaima@hust.edu.cn
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3099bcdc19 ]
bnxt_qplib_service_creq can be called from interrupt or tasklet or
process context. So the function take irq variant of spin_lock.
But when wake_up is invoked with the lock held, it is putting the
calling context to sleep.
[exception RIP: __wake_up_common+190]
RIP: ffffffffb7539d7e RSP: ffffa73300207ad8 RFLAGS: 00000083
RAX: 0000000000000001 RBX: ffff91fa295f69b8 RCX: dead000000000200
RDX: ffffa733344af940 RSI: ffffa73336527940 RDI: ffffa73336527940
RBP: 000000000000001c R8: 0000000000000002 R9: 00000000000299c0
R10: 0000017230de82c5 R11: 0000000000000002 R12: ffffa73300207b28
R13: 0000000000000000 R14: ffffa733341bf928 R15: 0000000000000000
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
Call the wakeup after releasing the lock.
Fixes: 1ac5a40479 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://lore.kernel.org/r/1686308514-11996-3-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0af91306e1 ]
Driver is not handling the wraparound of the mbox producer index correctly.
Currently the wraparound happens once u32 max is reached.
Bit 31 of the producer index register is special and should be set
only once for the first command. Because the producer index overflow
setting bit31 after a long time, FW goes to initialization sequence
and this causes FW hang.
Fix is to wraparound the mbox producer index once it reaches u16 max.
Fixes: cee0c7bba4 ("RDMA/bnxt_re: Refactor command queue management code")
Fixes: 1ac5a40479 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://lore.kernel.org/r/1686308514-11996-2-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 736a932736 ]
The commit 010c8bbad2 ("drm: msm: adreno: Disable preemption on Adreno
510") added special handling for a510 (this SKU doesn't seem to support
preemption, so the driver should clamp nr_rings to 1). However the
gpu->revn is not yet set (it is set later, in adreno_gpu_init()) and
thus the condition is always false. Check config->rev instead.
Fixes: 010c8bbad2 ("drm: msm: adreno: Disable preemption on Adreno 510")
Reported-by: Adam Skladowski <a39.skl@gmail.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Adam Skladowski <a39.skl@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/531511/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f0bcf49e9 ]
This is motivated by OOB access in amdgpu_vm_update_range when
offset_in_bo+map_size overflows.
v2: keep the validations in amdgpu_vm_bo_map
v3: add the validations to amdgpu_vm_bo_map/amdgpu_vm_bo_replace_map
rather than to amdgpu_gem_va_ioctl
Fixes: 9f7eb5367d ("drm/amdgpu: actually use the VM map parameters")
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Chia-I Wu <olvaffe@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49904a0ebf ]
While KUnit tests that cannot be built as a loadable module must depend
on "KUNIT=y", this is not true for modular tests, where it adds an
unnecessary limitation.
Fix this by relaxing the dependency to "KUNIT".
Fixes: 08809e482a ("HID: uclogic: KUnit best practices and naming conventions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: David Gow <davidgow@google.com>
Reviewed-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1becc57cd1 ]
Function rv740_get_decoded_reference_divider() may return 0 due to
unpredictable reference divider value calculated in
radeon_atom_get_clock_dividers(). This will lead to
division-by-zero error once that value is used as a divider
in calculating 'clk_s'.
While unlikely, this issue should nonetheless be prevented so add a
sanity check for such cases by testing 'decoded_ref' value against 0.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
v2: minor coding style fixes (Alex)
In practice this should actually happen as the vbios should be
properly populated.
Fixes: 66229b2005 ("drm/radeon/kms: add dpm support for rv7xx (v4)")
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b18f05a066 ]
[Why]
When freesync video mode is enabled, switching resolution from native
mode to one of the freesync video compatible modes can trigger continous
artifacts on some eDP panels when running under KDE. The articating can be seen in the
attached bug report.
[How]
Fix this by restricting updates that require full commit by using the same checks
for stream and scaling changes in the the enable pass of dm_update_crtc_state()
along with the check for compatible timings for freesync vide mode.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/2162
Fixes: da5e149097 ("drm/amd/display: Fix hang when skipping modeset")
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cabbdea1f1 ]
Pointer mqd_mem_obj can be deallocated in kfd_gtt_sa_allocate().
The function then returns non-zero value, which causes the second deallocation.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: d1f8f0d17d ("drm/amdkfd: Move non-sdma mqd allocation out of init_mqd")
Signed-off-by: Daniil Dulov <d.dulov@aladdin.ru>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08384e80a7 ]
The Device Tree was using invalid node names for the ACT8600 regulators.
To be fair, it is not the original committer's fault, as the
documentation did gives invalid names as well.
In theory, the fix should have been to modify the driver to accept the
alternative names. However, even though the act8865 driver spits
warnings, the kernel seemed to work fine with what is currently
supported upstream. For that reason, I think it is okay to just update
the DTS.
I removed the "regulator-name" too, since they really didn't bring any
information. The node names are enough.
Fixes: 73f2b94047 ("MIPS: CI20: DTS: Add I2C nodes")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b153a0bb41 ]
The PMON_CONFIG register on ADM1272 is a 16 bit register. Writing a 8 bit
value into it clears the upper 8 bits of the register, resulting in
unexpected side effects. Fix by writing the 16 bit register value.
Also, it has been reported that temperature readings are sometimes widely
inaccurate, to the point where readings may result in device shutdown due
to errant overtemperature faults. Improve by enabling temperature sampling.
While at it, move the common code for ADM1272 and ADM1278 into a separate
function, and clarify in the error message that an attempt was made to
enable both VOUT and temperature monitoring.
Last but not least, return the error code reported by the underlying I2C
controller and not -ENODEV if updating the PMON_CONFIG register fails.
After all, this does not indicate that the chip is not present, but an
error in the communication with the chip.
Fixes: 4ff0ce227a ("hwmon: (pmbus/adm1275) Add support for ADM1272")
Fixes: 9da9c2dc57 ("hwmon: (adm1275) enable adm1272 temperature reporting")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230602213447.3557346-1-linux@roeck-us.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3f2778b1b ]
The audio routing flow is not correct, the flow should be from source
(second element in the pair) to sink (first element in the pair). The
flow now is from "HP_OUT" to "Playback", where "Playback" is source
and "HP_OUT" is sink, i.e. the direction is swapped and there is no
direct link between the two either.
Fill in the correct routing, where "HP_OUT" supplies the "Headphone Jack",
"Line In Jack" supplies "LINE_IN" input, "Microphone Jack" supplies "MIC_IN"
input and "Mic Bias" supplies "Microphone Jack".
Fixes: 34e0c7847d ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0501fdec10 ]
make dtbs_check:
arch/arm/boot/dts/renesas/r8a7743-iwg20d-q7.dtb: backlight: pwms: [[58, 0, 5000000], [0]] is too long
From schema: Documentation/devicetree/bindings/leds/backlight/pwm-backlight.yaml
arch/arm/boot/dts/renesas/r8a7743-iwg20d-q7-dbcm-ca.dtb: backlight: pwms: [[67, 0, 5000000], [0]] is too long
From schema: Documentation/devicetree/bindings/leds/backlight/pwm-backlight.yaml
arch/arm/boot/dts/renesas/r8a7744-iwg20d-q7-dbcm-ca.dtb: backlight: pwms: [[67, 0, 5000000], [0]] is too long
From schema: Documentation/devicetree/bindings/leds/backlight/pwm-backlight.yaml
arch/arm/boot/dts/renesas/r8a7744-iwg20d-q7.dtb: backlight: pwms: [[58, 0, 5000000], [0]] is too long
From schema: Documentation/devicetree/bindings/leds/backlight/pwm-backlight.yaml
PWM specifiers referring to R-Car PWM Timer Controllers should contain
only two cells.
Fix this by dropping the bogus third cell.
Fixes: 6f89dd9e93 ("ARM: dts: iwg20d-q7-common: Add LCD support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/6e5c3167424a43faf8c1fa68d9667b3d87dc86d8.1684855911.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9358de193 ]
The hfi1 user SDMA pinned-page cache will leave a stale cache entry when
the cache-entry's virtual address range is invalidated but that cache
entry is in-use by an outstanding SDMA request.
Subsequent user SDMA requests with buffers in or spanning the virtual
address range of the stale cache entry will result in packets constructed
from the wrong memory, the physical pages pointed to by the stale cache
entry.
To fix this, remove mmu_rb_node cache entries from the mmu_rb_handler
cache independent of the cache entry's refcount. Add 'struct kref
refcount' to struct mmu_rb_node and manage mmu_rb_node lifetime with
kref_get() and kref_put().
mmu_rb_node.refcount makes sdma_mmu_node.refcount redundant. Remove
'atomic_t refcount' from struct sdma_mmu_node and change sdma_mmu_node
code to use mmu_rb_node.refcount.
Move the mmu_rb_handler destructor call after a
wait-for-SDMA-request-completion call so mmu_rb_nodes that need
mmu_rb_handler's workqueue to queue themselves up for destruction from an
interrupt context may do so.
Fixes: f48ad614c1 ("IB/hfi1: Move driver out of staging")
Fixes: 00cbce5cbf ("IB/hfi1: Fix bugs with non-PAGE_SIZE-end multi-iovec user SDMA requests")
Link: https://lore.kernel.org/r/168451393605.3700681.13493776139032178861.stgit@awfm-02.cornelisnetworks.com
Reviewed-by: Dean Luick <dean.luick@cornelisnetworks.com>
Signed-off-by: Brendan Cunningham <bcunningham@cornelisnetworks.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b002760f87 ]
Commit df8fc4e934 ("kbuild: Enable -fstrict-flex-arrays=3") triggers a
warning for fortified memset():
In function 'fortify_memset_chk',
inlined from 'irdma_clr_wqes' at drivers/infiniband/hw/irdma/uk.c:103:4:
include/linux/fortify-string.h:493:25: error: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
493 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The problem here isthat the inner array only has four 8-byte elements, so
clearing 4096 bytes overflows that. As this structure is part of an outer
array, change the code to pass a pointer to the irdma_qp_quanta instead,
and change the size argument for readability, matching the comment above
it.
Fixes: 551c46edc7 ("RDMA/irdma: Add user/kernel shared libraries")
Link: https://lore.kernel.org/r/20230523111859.2197825-1-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b1a78babd ]
Fix build errors in soc/fsl/qe/usb.c when QUICC_ENGINE is not set.
This happens when PPC_EP88XC is set, which selects CPM1 & CPM.
When CPM is set, USB_FSL_QE can be set without QUICC_ENGINE
being set. When USB_FSL_QE is set, QE_USB deafults to y, which
causes build errors when QUICC_ENGINE is not set. Making
QE_USB depend on QUICC_ENGINE prevents QE_USB from defaulting to y.
Fixes these build errors:
drivers/soc/fsl/qe/usb.o: in function `qe_usb_clock_set':
usb.c:(.text+0x1e): undefined reference to `qe_immr'
powerpc-linux-ld: usb.c:(.text+0x2a): undefined reference to `qe_immr'
powerpc-linux-ld: usb.c:(.text+0xbc): undefined reference to `qe_setbrg'
powerpc-linux-ld: usb.c:(.text+0xca): undefined reference to `cmxgcr_lock'
powerpc-linux-ld: usb.c:(.text+0xce): undefined reference to `cmxgcr_lock'
Fixes: 5e41486c40 ("powerpc/QE: add support for QE USB clocks routing")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/all/202301101500.pillNv6R-lkp@intel.com/
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Leo Li <leoyang.li@nxp.com>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Nicolas Schier <nicolas@fjasle.eu>
Cc: Qiang Zhao <qiang.zhao@nxp.com>
Cc: linuxppc-dev <linuxppc-dev@lists.ozlabs.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Nicolas Schier <nicolas@jasle.eu>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60413129ee ]
When using the codec through the generic audio graph card, there are at
least two calls of es8316_set_dai_sysclk(), with the effect of limiting
the allowed sample rates according to the MCLK/LRCK ratios supported by
the codec:
1. During audio card setup, to set the initial MCLK - see
asoc_simple_init_dai().
2. Before opening a stream, to update MCLK, according to the stream
sample rate and the multiplication factor - see
asoc_simple_hw_params().
In some cases the initial MCLK might be set to a frequency that doesn't
match any of the supported ratios, e.g. 12287999 instead of 12288000,
which is only 1 Hz below the supported clock, as that is what the
hardware reports. This creates an empty list of rate constraints, which
is further passed to snd_pcm_hw_constraint_list() via
es8316_pcm_startup(), and causes the following error on the very first
access of the sound card:
$ speaker-test -D hw:Analog,0 -F S16_LE -c 2 -t wav
Broken configuration for playback: no configurations available: Invalid argument
Setting of hwparams failed: Invalid argument
Note that all subsequent retries succeed thanks to the updated MCLK set
at point 2 above, which uses a computed frequency value instead of a
reading from the hardware registers. Normally this would have mitigated
the issue, but es8316_pcm_startup() executes before the 2nd call to
es8316_set_dai_sysclk(), hence it cannot make use of the updated
constraints.
Since es8316_pcm_hw_params() performs anyway a final validation of MCLK
against the stream sample rate and the supported MCLK/LRCK ratios, fix
the issue by ensuring that sysclk_constraints list is only set when at
least one supported sample rate is autodetected by the codec.
Fixes: b8b88b7087 ("ASoC: add es8316 codec driver")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20230530181140.483936-3-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f07342903 ]
The following error occurs when trying to restore a previously saved
ALSA mixer state (tested on a Rock 5B board):
$ alsactl --no-ucm -f /tmp/asound.state store hw:Analog
$ alsactl --no-ucm -I -f /tmp/asound.state restore hw:Analog
alsactl: set_control:1475: Cannot write control '2:0:0:ALC Capture Target Volume:0' : Invalid argument
According to ES8316 datasheet, the register at address 0x2B, which is
related to the above mixer control, contains by default the value 0xB0.
Considering the corresponding ALC target bits (ALCLVL) are 7:4, the
control is initialized with 11, which is one step above the maximum
value allowed by the driver:
ALCLVL | dB gain
-------+--------
0000 | -16.5
0001 | -15.0
0010 | -13.5
.... | .....
0111 | -6.0
1000 | -4.5
1001 | -3.0
1010 | -1.5
.... | .....
1111 | -1.5
The tests performed using the VU meter feature (--vumeter=TYPE) of
arecord/aplay confirm the specs are correct and there is no measured
gain if the 1011-1111 range would have been mapped to 0 dB:
dB gain | VU meter %
--------+-----------
-6.0 | 30-31
-4.5 | 35-36
-3.0 | 42-43
-1.5 | 50-51
0.0 | 50-51
Increment the max value allowed for ALC Capture Target Volume control,
so that it matches the hardware default. Additionally, update the
related TLV to prevent an artificial extension of the dB gain range.
Fixes: b8b88b7087 ("ASoC: add es8316 codec driver")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20230530181140.483936-2-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0cf765e598 ]
Fix the following error in kernel log due to too long sound card name:
"
asoc-audio-graph-card sound: ASoC: driver name too long 'STM32MP1-AV96-HDMI' -> 'STM32MP1-AV96-H'
"
Fixes: e027da3427 ("ARM: dts: stm32: Add bindings for audio on AV96")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 861bc1d288 ]
omap2 contains a hack to define tick_broadcast() on non-SMP
configurations in place of the normal SMP definition. This one
causes a warning because of a missing prototype:
arch/arm/mach-omap2/board-generic.c:44:6: error: no previous prototype for 'tick_broadcast'
Make sure to always include the header with the declaration.
Fixes: d86ad463d6 ("ARM: OMAP2+: Fix regression for using local timer on non-SMP SoCs")
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Link: https://lore.kernel.org/r/20230516153109.514251-9-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 419013740e ]
ep93xx_clocksource_read() is only called from the file it is declared in,
while ep93xx_timer_init() is declared in a header that is not included here.
arch/arm/mach-ep93xx/timer-ep93xx.c:120:13: error: no previous prototype for 'ep93xx_timer_init'
arch/arm/mach-ep93xx/timer-ep93xx.c:63:5: error: no previous prototype for 'ep93xx_clocksource_read'
Fixes: 000bc17817 ("ARM: ep93xx: switch to GENERIC_CLOCKEVENTS")
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20230516153109.514251-3-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f24b495508 ]
The previous setting was related to the overall dimension and not to the
active display area.
In the "PHYSICAL SPECIFICATIONS" section, the datasheet shows the
following parameters:
----------------------------------------------------------
| Item | Specifications | unit |
----------------------------------------------------------
| Display area | 98.7 (W) x 57.5 (H) | mm |
----------------------------------------------------------
| Overall dimension | 105.5(W) x 67.2(H) x 4.96(D) | mm |
----------------------------------------------------------
Fixes: 966fea78ad ("drm/panel: simple: Add support for Ampire AM-480272H3TMQW-T01H")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
[narmstrong: fixed Fixes commit id length]
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230516085039.3797303-1-dario.binacchi@amarulasolutions.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd9e329af7 ]
The datasheet describes the following initialization flow including
minimum delay times between each step:
1. DSI data lanes need to be in LP-11 and the clock lane in HS mode
2. toggle EN signal
3. initialize registers
4. enable PLL
5. soft reset
6. enable DSI stream
7. check error status register
To meet this requirement we need to make sure the host bridge's
pre_enable() is called first by using the pre_enable_prev_first
flag.
Furthermore we need to split enable() into pre_enable() which covers
steps 2-5 from above and enable() which covers step 7 and is called
after the host bridge's enable().
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Fixes: ceb515ba29 ("drm/bridge: ti-sn65dsi83: Add TI SN65DSI83 and SN65DSI84 driver")
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> #TQMa8MxML/MBa8Mx
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230503163313.2640898-3-frieder@fris.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5500f823db ]
The 96Boards specification expects a 1.8V power rail on the low-speed
expansion connector that is able to provide at least 0.18W / 100 mA.
According to the DB410c hardware user manual this is done by connecting
both L15 and L16 in parallel with up to 55mA each (for 110 mA total) [1].
Unfortunately the current regulator setup in the DB410c device tree
does not implement the specification correctly and only provides 5 mA:
- Only L15 is marked always-on, so L16 is never enabled.
- Without specifying a load the regulator is put into LPM where
it can only provide 5 mA.
Fix this by:
- Adding proper voltage constraints for L16.
- Making L16 always-on.
- Adding regulator-system-load for both L15 and L16. 100 mA should be
available in total, so specify 50 mA for each. (The regulator
hardware can only be in normal (55 mA) or low-power mode (5 mA) so
this will actually result in the expected 110 mA total...)
[1]: https://www.96boards.org/documentation/consumer/dragonboard/dragonboard410c/hardware-docs/hardware-user-manual.md.html#power-supplies
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: 828dd5d66f ("arm64: dts: apq8016-sbc: make 1.8v available on LS expansion")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230510-msm8916-regulators-v1-2-54d4960a05fc@gerhold.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e27654df20 ]
For some reason DB410c has completely bogus regulator constraints that
actually just correspond to the programmable voltages which are already
provided by the regulator driver. Some of them are not just outside the
recommended operating conditions of the APQ8016E SoC but even exceed
the absolute maximum ratings, potentially risking permanent device
damage.
In practice it's not quite as dangerous thanks to the RPM firmware:
It turns out that it has its own voltage constraints and silently
clamps all regulator requests. For example, requesting 3.3V for L5
(allowed by the current regulator constraints!) still results in 1.8V
being programmed in the actual regulator hardware.
Experimentation with various voltages shows that the internal RPM
voltage constraints roughly correspond to the safe "specified range"
in the PM8916 Device Specification (rather than the "programmable
range" used inside apq8016-sbc.dtsi right now).
Combine those together with some fixed voltages used in the old
msm-3.10 device tree from Qualcomm to give DB410c some actually valid
voltage constraints.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: 4c7d53d16d ("arm64: dts: apq8016-sbc: add regulators support")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230510-msm8916-regulators-v1-1-54d4960a05fc@gerhold.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e47a807843 ]
Add a family compatible for QCE IP on SM8550 SoC, which is equal to QCE IP
found on SM8150 SoC and described in the recently updated device tree
bindings documentation, as well add a generic QCE IP family compatible.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Stable-dep-of: 3cbf49ef16 ("arm64: dts: qcom: sm8550: correct crypto unit address")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3244442406 ]
On MSM8916 the wireless connectivity functionality (WiFi/Bluetooth) is
split into the digital part inside the SoC and the analog RF part inside
a supplementary WCN36xx chip. For MSM8916, three different options
exist:
- WCN3620 (WLAN 802.11 b/g/n 2.4 GHz + Bluetooth)
- WCN3660B (WLAN 802.11 a/b/g/n 2.4/5 GHz + Bluetooth)
- WCN3680B (WLAN 802.11ac 2.4/5 GHz + Bluetooth)
Choosing one of these is up to the board vendor. This means that the
compatible belongs into the board-specific DT part so people porting
new boards pay attention to set the correct compatible.
Right now msm8916.dtsi sets "qcom,wcn3620" as default compatible,
which does not work at all for boards that have WCN3660B or WCN3680B.
Remove the default compatible from msm8196.dtsi and move it to the board
DT as follows:
- Boards with only &pronto { status = "okay"; } used the default
"qcom,wcn3620" so far. They now set this explicitly for &wcnss_iris.
- Boards with &pronto { ... iris { compatible = "qcom,wcn3660b"; }};
already had an override that just moves to &wcnss_iris now.
- For msm8916-samsung-a2015-common.dtsi the WCN compatible differs for
boards making use of it (a3u: wcn3620, a5u: wcn3660b, e2015: wcn3620)
so the definitions move to the board-specific DT part.
Since this requires touching all the board DTs, use this as a chance to
name the WCNSS-related labels consistently, so everything is grouped
properly when sorted alphabetically.
No functional change, just clean-up for more clarity & easier porting.
Aside from ordering the generated DTBs are identical.
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230309091452.1011776-1-stephan.gerhold@kernkonzept.com
Stable-dep-of: 1f9a41bb0b ("arm64: dts: qcom: msm8916: correct WCNSS unit address")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c32c81f3db ]
Aaro reports problems on the OSK1 board after we altered
the dynamic base for GPIO allocations.
It appears this happens because the OMAP driver now
allocates GPIO numbers dynamically, so all that is
references by number is a bit up in the air.
Let's bite the bullet and try to just move the gpio_chip
in the tps65010 MFD driver over to using dynamic allocations.
Alter everything in the OSK1 board file to use a GPIO
descriptor table and lookups.
Utilize the NULL device to define some board-specific
GPIO lookups and use these to immediately look up the
same GPIOs, convert to IRQ numbers and pass as resources
to the devices. This is ugly but should work.
The .setup() callback for tps65010 was used for some GPIO
hogging, but since the OSK1 is the only user in the entire
kernel we can alter the signatures to something that
is helpful and make a clean transition.
Fixes: 92bf78b33b ("gpio: omap: use dynamic allocation of base")
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: andy.shevchenko@gmail.com
Cc: Andreas Kemnade <andreas@kemnade.info>
Acked-by: Lee Jones <lee@kernel.org>
Reviewed-by: Lee Jones <lee@kernel.org>
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1464e48d69 ]
During probe, the driver registers i2c dummy devices and populates the
aux bus, which registers a device for the panel. After doing that, the
driver can still defer probe if needed. This ordering of operations is
troublesome however, because the deferred probe work will retry probing
all pending devices every time a new device is registered. Therefore, if
modules need to be loaded in order to satisfy the dependencies for this
driver to complete probe, the kernel will stall, since it'll keep trying
to probe the anx7625 driver, but never succeed, given that modules would
only be loaded after the deferred probe work completes.
Two changes are required to avoid this issue:
* Move of_find_mipi_dsi_host_by_node(), which can defer probe, to before
anx7625_register_i2c_dummy_clients() and
devm_of_dp_aux_populate_ep_devices(), which register devices.
* Make use of the done_probing callback when populating the aux bus,
so that the bridge registration is only done after the panel is
probed. This is required because the panel might need to defer probe,
but the aux bus population needs the i2c dummy devices working, so
this call couldn't just be moved to an earlier point in probe.
One caveat is that if the panel is described outside the aux bus, the
probe loop issue can still happen, but we don't have a way to avoid
it in that case since there's no callback available.
With this patch applied, it's possible to boot on
mt8192-asurada-spherion with
CONFIG_DRM_ANALOGIX_ANX7625=y
CONFIG_MTK_MMSYS=m
CONFIG_BACKLIGHT_PWM=y
and also with
CONFIG_DRM_ANALOGIX_ANX7625=y
CONFIG_MTK_MMSYS=y
CONFIG_BACKLIGHT_PWM=m
Fixes: adca62ec37 ("drm/bridge: anx7625: Support reading edid through aux channel")
Fixes: 269332997a ("drm/bridge: anx7625: Return -EPROBE_DEFER if the dsi host was not found")
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230518193902.891121-1-nfraprado@collabora.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ffec92e70 ]
The model property should be at the top level, let's move it out
of the pinctrl node.
Fixes: d2eaf949d2 ("ARM: dts: omap3-gta04a5one: define GTA04A5 variant with OneNAND")
Cc: Andreas Kemnade <andreas@kemnade.info>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7061b6af34 ]
When map() is called on a detached domain, the domain does not exist in
the device so we do not send a MAP request, but we do update the
internal mapping tree, to be replayed on the next attach. Since this
constitutes a successful iommu_map() call, return *mapped in this case
too.
Fixes: 7e62edd7a3 ("iommu/virtio: Add map/unmap_pages() callbacks implementation")
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/20230515113946.1017624-3-jean-philippe@linaro.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff2e4bfd16 ]
bnxt_re currently uses the names "bnxt_qplib_creq" and "bnxt_qplib_nq-0"
while registering IRQs. There is no way to distinguish the IRQs of
different device ports when there are multiple IB devices registered.
This could make the scenarios worse where one want to pin IRQs of a device
port to certain CPUs.
Fixed the code to use unique names which has PCI BDF information while
registering interrupts like: "bnxt_re-nq-0@pci:0000:65:00.0" and
"bnxt_re-creq@pci:0000:65:00.1".
Fixes: 1ac5a40479 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Link: https://lore.kernel.org/r/1684478897-12247-4-git-send-email-selvin.xavier@broadcom.com
Reviewed-by: Bhargava Chenna Marreddy <bhargava.marreddy@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab112ee789 ]
When the ulp hook to start the IRQ fails because the rings are not
available, tasklets are not enabled. In this case when the driver is
unloaded, driver calls CREQ tasklet_kill. This causes an indefinite hang
as the tasklet is not enabled.
Driver shouldn't call tasklet_kill if it is not enabled. So using the
creq->requested and nq->requested flags to identify if both tasklets/irqs
are registered. Checking this flag while scheduling the tasklet from
ISR. Also, added a cleanup for disabling tasklet, in case request_irq
fails during start_irq.
Check for return value for bnxt_qplib_rcfw_start_irq and in case the
bnxt_qplib_rcfw_start_irq fails, return bnxt_re_start_irq without
attempting to start NQ IRQs.
Fixes: 1ac5a40479 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Link: https://lore.kernel.org/r/1684478897-12247-2-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0babf89c9c ]
In the unlikely event that something goes wrong with the device and
its registers, the fan_from_reg() function may return 0. This value
will cause a division-by-zero error in the show_pwm() function.
To prevent this, test the value of
fan_from_reg(data->fan_full_speed[nr]) against 0 before performing
the division. If the division-by-zero error is avoided, assign 0 to
the val variable.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: df9ec2dae0 ("hwmon: (f71882fg) Reorder symbols to get rid of a few forward declarations")
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Link: https://lore.kernel.org/r/20230510143537.145060-1-n.zhandarovich@fintech.ru
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 70be83708c ]
PSCI is not implemented on SparX-5 at all, there is no ATF and U-boot that
is shipped does not implement it as well.
I have tried flashing the latest BSP 2022.12 U-boot which did not work.
After contacting Microchip, they confirmed that there is no ATF for the
SoC nor PSCI implementation which is unfortunate in 2023.
So, disable PSCI as otherwise kernel crashes as soon as it tries probing
PSCI with, and the crash is only visible if earlycon is used.
Since PSCI is not implemented, switch core bringup to use spin-tables
which are implemented in the vendor U-boot and actually work.
Tested on PCB134 with eMMC (VSC5640EV).
Fixes: 6694aee00a ("arm64: dts: sparx5: Add basic cpu support")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Acked-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Link: https://lore.kernel.org/r/20230221105039.316819-1-robert.marko@sartura.hr
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9660efc2af ]
The ethernet MAC EEPROM is not populated on the SoM itself, it has to be
populated on each carrier board. Move the EEPROM into the correct place
in DTs, i.e. the carrier board DTs. Add label to the EEPROM too.
Fixes: 7e76f82acd ("ARM: dts: stm32: Split Avenger96 into DHCOR SoM and Avenger96 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab87f558dc ]
Currently, the pixel conversion isn't rounding the fixed-point values
before assigning it to the RGB coefficients, which is causing the IGT
pixel-format tests to fail. So, use the drm_fixp2int_round() fixed-point
helper to round the values when assigning it to the RGB coefficients.
Tested with igt@kms_plane@pixel-format and igt@kms_plane@pixel-format-source-clamping.
[v2]:
* Use drm_fixp2int_round() to fix the pixel conversion instead of
casting the values to s32 (Melissa Wen).
Fixes: 89b03aeaef ("drm/vkms: fix 32bit compilation error by replacing macros")
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Arthur Grillo <arthurgrillo@riseup.net>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20230512104044.65034-2-mcanal@igalia.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 123ee07ba5 ]
Smatch reports:
drivers/gpu/drm/sun4i/sun4i_tcon.c:805 sun4i_tcon_init_clocks() warn:
'tcon->clk' from clk_prepare_enable() not released on lines: 792,801.
In the function sun4i_tcon_init_clocks(), tcon->clk and tcon->sclk0 are
not disabled in the error handling, which affects the release of
these variable. Although sun4i_tcon_bind(), which calls
sun4i_tcon_init_clocks(), use sun4i_tcon_free_clocks to disable the
variables mentioned, but the error handling branch of
sun4i_tcon_init_clocks() ignores the required disable process.
To fix this issue, use the devm_clk_get_enabled to automatically
balance enable and disabled calls. As original implementation use
sun4i_tcon_free_clocks() to disable clk explicitly, we delete the
related calls and error handling that are no longer needed.
Fixes: 9026e0d122 ("drm: Add Allwinner A10 Display Engine support")
Fixes: b14e945bda ("drm/sun4i: tcon: Prepare and enable TCON channel 0 clock at init")
Fixes: 8e92404725 ("drm/sun4i: support TCONs without channel 1")
Fixes: 34d698f6e3 ("drm/sun4i: Add has_channel_0 TCON quirk")
Signed-off-by: XuDong Liu <m202071377@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20230430112347.4689-1-m202071377@hust.edu.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad527ca87e ]
The .driver_data content in i2c_device_id table must match the
.data content in of_device_id table, else device_get_match_data()
would return bogus value on i2c_device_id match. Align the two
tables.
The i2c_device_id table is now converted from of_device_id using
's@.compatible = "renesas,\([^"]\+"\), .data = \(.*\)@"\1, .driver_data = (kernel_ulong_t)\2@'
Fixes: 892e0ddea1 ("clk: rs9: Add Renesas 9-series PCIe clock generator driver")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Link: https://lore.kernel.org/r/20230507133906.15061-3-marek.vasut+renesas@mailbox.org
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b5e10beeaf ]
The .driver_data content in i2c_device_id table must match the
.data content in of_device_id table, else device_get_match_data()
would return bogus value on i2c_device_id match. Align the two
tables.
The i2c_device_id table is now converted from of_device_id using
's@.compatible = "renesas,\([^"]\+"\), .data = \(.*\)@"\1, .driver_data = (kernel_ulong_t)\2@'
Fixes: 48c5e98fed ("clk: Renesas versaclock7 ccf device driver")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Link: https://lore.kernel.org/r/20230507133906.15061-2-marek.vasut+renesas@mailbox.org
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3c8e2c575 ]
There is no such property in the SPI controller binding documentation.
Also Linux driver doesn't look for it.
This fixes:
arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dtb: spi@18029200: Unevaluated properties are not allowed ('clock-names' was unexpected)
From schema: Documentation/devicetree/bindings/spi/brcm,spi-bcm-qspi.yaml
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20230503122830.3200-1-zajec5@gmail.com
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bac7842cd1 ]
Correct computation of THS_TRAILCNT register.
This register must be set to a value that ensure that
THS_TRAIL > 60 ns + 4 x UI
and
THS_TRAIL > 8 x UI
and
THS_TRAIL < TEOT
with
TEOT = 105 ns + (12 x UI)
with the actual value of THS_TRAIL being
(1 + THS_TRAILCNT) x ByteClk cycle + ((1 to 2) + 2) xHSBYTECLK cycle +
- (PHY output delay)
with PHY output delay being about
(8 + (5 to 6)) x MIPIBitClk cycle in the BitClk conversion.
Fixes: ff1ca6397b ("drm/bridge: Add tc358768 driver")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-9-francesco@dolcini.it
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77a089328d ]
Correct computation of THS_ZEROCNT register.
This register must be set to a value that ensure that
THS_PREPARE + THS_ZERO > 145ns + 10*UI
with the actual value of (THS_PREPARE + THS_ZERO) being
((1 to 2) + 1 + (TCLK_ZEROCNT + 1) + (3 to 4)) x ByteClk cycle +
+ HSByteClk x (2 + (1 to 2)) + (PHY delay)
with PHY delay being about
(8 + (5 to 6)) x MIPIBitClk cycle in the BitClk conversion.
Fixes: ff1ca6397b ("drm/bridge: Add tc358768 driver")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-7-francesco@dolcini.it
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75a8aeac25 ]
Always enable HS video mode setting the TXMD bit, without this change no
video output is present with DSI sinks that are setting
MIPI_DSI_MODE_LPM flag (tested with LT8912B DSI-HDMI bridge).
Previously the driver was enabling HS mode only when the DSI sink was
not explicitly setting the MIPI_DSI_MODE_LPM, however this is not
correct.
The MIPI_DSI_MODE_LPM is supposed to indicate that the sink is willing
to receive data in low power mode, however clearing the
TC358768_DSI_CONTROL_TXMD bit will make the TC358768 send video in
LP mode that is not the intended behavior.
Fixes: ff1ca6397b ("drm/bridge: Add tc358768 driver")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-2-francesco@dolcini.it
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dbe836576f ]
The watchdog_timer can schedule tx_timeout_task and watchdog_work
can also arm watchdog_timer. The process is shown below:
----------- timer schedules work ------------
cyttsp4_watchdog_timer() //timer handler
schedule_work(&cd->watchdog_work)
----------- work arms timer ------------
cyttsp4_watchdog_work() //workqueue callback function
cyttsp4_start_wd_timer()
mod_timer(&cd->watchdog_timer, ...)
Although del_timer_sync() and cancel_work_sync() are called in
cyttsp4_remove(), the timer and workqueue could still be rearmed.
As a result, the possible use after free bugs could happen. The
process is shown below:
(cleanup routine) | (timer and workqueue routine)
cyttsp4_remove() | cyttsp4_watchdog_timer() //timer
cyttsp4_stop_wd_timer() | schedule_work()
del_timer_sync() |
| cyttsp4_watchdog_work() //worker
| cyttsp4_start_wd_timer()
| mod_timer()
cancel_work_sync() |
| cyttsp4_watchdog_timer() //timer
| schedule_work()
del_timer_sync() |
kfree(cd) //FREE |
| cyttsp4_watchdog_work() // reschedule!
| cd-> //USE
This patch changes del_timer_sync() to timer_shutdown_sync(),
which could prevent rearming of the timer from the workqueue.
Fixes: 17fb1563d6 ("Input: cyttsp4 - add core driver for Cypress TMA4XX touchscreen devices")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20230421082919.8471-1-duoming@zju.edu.cn
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55f9720dbf ]
SLPC enables use of efficient freq at init by default. It is
possible for GuC to request frequencies that are higher than
the 'software' max if user has set it lower than the efficient
level.
Scenarios/tests that require strict fixing of freq below the efficient
level will need to disable it through this interface.
v2: Keep just one interface to toggle sysfs. With this, user will
be completely responsible for toggling efficient frequency if need
be. There will be no implicit disabling when user sets min < RP1 (Ashutosh)
v3: Remove unused label, review comments (Ashutosh)
v4: Toggle efficient freq usage in SLPC selftest and checkpatch fixes
v5: Review comments (Andi) and add a separate patch for selftest updates
Fixes: 95ccf312a1 ("drm/i915/guc/slpc: Allow SLPC to use efficient frequency")
Signed-off-by: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230426003942.1924347-1-vinay.belgaumkar@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 710cc1e7cd ]
[Why]
The bit for flip addr is being set causing the determination for
FAST vs MEDIUM to always return MEDIUM when plane info is provided
as a surface update. This causes extreme stuttering for the typical
atomic update path on Linux.
[How]
Don't use update_flags->raw for determining FAST vs MEDIUM. It's too
fragile to changes like this.
Explicitly specify the update type per update flag instead. It's not
as clever as checking the bits itself but at least it's correct.
Fixes: aa5fdb1ab5 ("drm/amd/display: Explicitly specify update type per plane info change")
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20c3dffdcc ]
Several calls to ci_dpm_fini() will attempt to free resources that
either have been freed before or haven't been allocated yet. This
may lead to undefined or dangerous behaviour.
For instance, if r600_parse_extended_power_table() fails, it might
call r600_free_extended_power_table() as will ci_dpm_fini() later
during error handling.
Fix this by only freeing pointers to objects previously allocated.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: cc8dbbb4f6 ("drm/radeon: add dpm support for CI dGPUs (v2)")
Co-developed-by: Natalia Petrova <n.petrova@fintech.ru>
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3306ba4b60 ]
Three functions in the amdgpu display driver cause -Wmissing-prototype
warnings:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_resource.c:1858:6: error: no previous prototype for 'is_timing_changed' [-Werror=missing-prototypes]
is_timing_changed() is actually meant to be a global symbol, but needs
a proper name and prototype.
Fixes: 17ce8a6907 ("drm/amd/display: Add dsc pre-validation in atomic check")
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d06f925f13 ]
When using the felix driver (the only one which supports UC filtering
and MC filtering) as a DSA master for a random other DSA switch, one can
see the following stack trace when the downstream switch ports join a
VLAN-aware bridge:
=============================
WARNING: suspicious RCU usage
-----------------------------
net/8021q/vlan_core.c:238 suspicious rcu_dereference_protected() usage!
stack backtrace:
Workqueue: dsa_ordered dsa_slave_switchdev_event_work
Call trace:
lockdep_rcu_suspicious+0x170/0x210
vlan_for_each+0x8c/0x188
dsa_slave_sync_uc+0x128/0x178
__hw_addr_sync_dev+0x138/0x158
dsa_slave_set_rx_mode+0x58/0x70
__dev_set_rx_mode+0x88/0xa8
dev_uc_add+0x74/0xa0
dsa_port_bridge_host_fdb_add+0xec/0x180
dsa_slave_switchdev_event_work+0x7c/0x1c8
process_one_work+0x290/0x568
What it's saying is that vlan_for_each() expects rtnl_lock() context and
it's not getting it, when it's called from the DSA master's ndo_set_rx_mode().
The caller of that - dsa_slave_set_rx_mode() - is the slave DSA
interface's dsa_port_bridge_host_fdb_add() which comes from the deferred
dsa_slave_switchdev_event_work().
We went to great lengths to avoid the rtnl_lock() context in that call
path in commit 0faf890fc5 ("net: dsa: drop rtnl_lock from
dsa_slave_switchdev_event_work"), and calling rtnl_lock() is simply not
an option due to the possibility of deadlocking when calling
dsa_flush_workqueue() from the call paths that do hold rtnl_lock() -
basically all of them.
So, when the DSA master calls vlan_for_each() from its ndo_set_rx_mode(),
the state of the 8021q driver on this device is really not protected
from concurrent access by anything.
Looking at net/8021q/, I don't think that vlan_info->vid_list was
particularly designed with RCU traversal in mind, so introducing an RCU
read-side form of vlan_for_each() - vlan_for_each_rcu() - won't be so
easy, and it also wouldn't be exactly what we need anyway.
In general I believe that the solution isn't in net/8021q/ anyway;
vlan_for_each() is not cut out for this task. DSA doesn't need rtnl_lock()
to be held per se - since it's not a netdev state change that we're
blocking, but rather, just concurrent additions/removals to a VLAN list.
We don't even need sleepable context - the callback of vlan_for_each()
just schedules deferred work.
The proposed escape is to remove the dependency on vlan_for_each() and
to open-code a non-sleepable, rtnl-free alternative to that, based on
copies of the VLAN list modified from .ndo_vlan_rx_add_vid() and
.ndo_vlan_rx_kill_vid().
Fixes: 64fdc5f341 ("net: dsa: sync unicast and multicast addresses for VLAN filters too")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20230626154402.3154454-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a9922e7be ]
ipvlan_queue_xmit() should return NET_XMIT_XXX, but
ipvlan_xmit_mode_l2/l3() returns rx_handler_result_t or NET_RX_XXX
in some cases. ipvlan_rcv_frame() will only return RX_HANDLER_CONSUMED
in ipvlan_xmit_mode_l2/l3() because 'local' is true. It's equal to
NET_XMIT_SUCCESS. But dev_forward_skb() can return NET_RX_SUCCESS or
NET_RX_DROP, and returning NET_RX_DROP(NET_XMIT_DROP) will increase
both ipvlan and ipvlan->phy_dev drops counter.
The skb to forward can be treated as xmitted successfully. This patch
makes ipvlan_queue_xmit() return NET_XMIT_SUCCESS for forward skb.
Fixes: 2ad7bf3638 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Cambda Zhu <cambda@linux.alibaba.com>
Link: https://lore.kernel.org/r/20230626093347.7492-1-cambda@linux.alibaba.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f188d30087 ]
ct_sip_parse_numerical_param() returns only 0 or 1 now.
But process_register_request() and process_register_response() imply
checking for a negative value if parsing of a numerical header parameter
failed.
The invocation in nf_nat_sip() looks correct:
if (ct_sip_parse_numerical_param(...) > 0 &&
...) { ... }
Make the return value of the function ct_sip_parse_numerical_param()
a tristate to fix all the cases
a) return 1 if value is found; *val is set
b) return 0 if value is not found; *val is unchanged
c) return -1 on error; *val is undefined
Found by InfoTeCS on behalf of Linux Verification Center
(linuxtesting.org) with SVACE.
Fixes: 0f32a40fc9 ("[NETFILTER]: nf_conntrack_sip: create signalling expectations")
Signed-off-by: Ilia.Gavrilov <Ilia.Gavrilov@infotecs.ru>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff0a3a7d52 ]
Eric Dumazet says:
nf_conntrack_dccp_packet() has an unique:
dh = skb_header_pointer(skb, dataoff, sizeof(_dh), &_dh);
And nothing more is 'pulled' from the packet, depending on the content.
dh->dccph_doff, and/or dh->dccph_x ...)
So dccp_ack_seq() is happily reading stuff past the _dh buffer.
BUG: KASAN: stack-out-of-bounds in nf_conntrack_dccp_packet+0x1134/0x11c0
Read of size 4 at addr ffff000128f66e0c by task syz-executor.2/29371
[..]
Fix this by increasing the stack buffer to also include room for
the extra sequence numbers and all the known dccp packet type headers,
then pull again after the initial validation of the basic header.
While at it, mark packets invalid that lack 48bit sequence bit but
where RFC says the type MUST use them.
Compile tested only.
v2: first skb_header_pointer() now needs to adjust the size to
only pull the generic header. (Eric)
Heads-up: I intend to remove dccp conntrack support later this year.
Fixes: 2bc780499a ("[NETFILTER]: nf_conntrack: add DCCP protocol support")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f67fbf819 ]
The `shift` variable which indicates the offset in the string at which
to start matching the pattern is initialized to `bm->patlen - 1`, but it
is not reset when a new block is retrieved. This means the implemen-
tation may start looking at later and later positions in each successive
block and miss occurrences of the pattern at the beginning. E.g.,
consider a HTTP packet held in a non-linear skb, where the HTTP request
line occurs in the second block:
[... 52 bytes of packet headers ...]
GET /bmtest HTTP/1.1\r\nHost: www.example.com\r\n\r\n
and the pattern is "GET /bmtest".
Once the first block comprising the packet headers has been examined,
`shift` will be pointing to somewhere near the end of the block, and so
when the second block is examined the request line at the beginning will
be missed.
Reinitialize the variable for each new block.
Fixes: 8082e4ed0a ("[LIB]: Boyer-Moore extension for textsearch infrastructure strike #2")
Link: https://bugzilla.netfilter.org/show_bug.cgi?id=1390
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6709d4b7bc ]
This commit fixes several use-after-free that caused by function
nfc_llcp_find_local(). For example, one UAF can happen when below buggy
time window occurs.
// nfc_genl_llc_get_params | // nfc_unregister_device
|
dev = nfc_get_device(idx); | device_lock(...)
if (!dev) | dev->shutting_down = true;
return -ENODEV; | device_unlock(...);
|
device_lock(...); | // nfc_llcp_unregister_device
| nfc_llcp_find_local()
nfc_llcp_find_local(...); |
| local_cleanup()
if (!local) { |
rc = -ENODEV; | // nfc_llcp_local_put
goto exit; | kref_put(.., local_release)
} |
| // local_release
| list_del(&local->list)
// nfc_genl_send_params | kfree()
local->dev->idx !!!UAF!!! |
|
and the crash trace for the one of the discussed UAF like:
BUG: KASAN: slab-use-after-free in nfc_genl_llc_get_params+0x72f/0x780 net/nfc/netlink.c:1045
Read of size 8 at addr ffff888105b0e410 by task 20114
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x72/0xa0 lib/dump_stack.c:106
print_address_description mm/kasan/report.c:319 [inline]
print_report+0xcc/0x620 mm/kasan/report.c:430
kasan_report+0xb2/0xe0 mm/kasan/report.c:536
nfc_genl_send_params net/nfc/netlink.c:999 [inline]
nfc_genl_llc_get_params+0x72f/0x780 net/nfc/netlink.c:1045
genl_family_rcv_msg_doit.isra.0+0x1ee/0x2e0 net/netlink/genetlink.c:968
genl_family_rcv_msg net/netlink/genetlink.c:1048 [inline]
genl_rcv_msg+0x503/0x7d0 net/netlink/genetlink.c:1065
netlink_rcv_skb+0x161/0x430 net/netlink/af_netlink.c:2548
genl_rcv+0x28/0x40 net/netlink/genetlink.c:1076
netlink_unicast_kernel net/netlink/af_netlink.c:1339 [inline]
netlink_unicast+0x644/0x900 net/netlink/af_netlink.c:1365
netlink_sendmsg+0x934/0xe70 net/netlink/af_netlink.c:1913
sock_sendmsg_nosec net/socket.c:724 [inline]
sock_sendmsg+0x1b6/0x200 net/socket.c:747
____sys_sendmsg+0x6e9/0x890 net/socket.c:2501
___sys_sendmsg+0x110/0x1b0 net/socket.c:2555
__sys_sendmsg+0xf7/0x1d0 net/socket.c:2584
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3f/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x72/0xdc
RIP: 0033:0x7f34640a2389
RSP: 002b:00007f3463415168 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007f34641c1f80 RCX: 00007f34640a2389
RDX: 0000000000000000 RSI: 0000000020000240 RDI: 0000000000000006
RBP: 00007f34640ed493 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 00007ffe38449ecf R14: 00007f3463415300 R15: 0000000000022000
</TASK>
Allocated by task 20116:
kasan_save_stack+0x22/0x50 mm/kasan/common.c:45
kasan_set_track+0x25/0x30 mm/kasan/common.c:52
____kasan_kmalloc mm/kasan/common.c:374 [inline]
__kasan_kmalloc+0x7f/0x90 mm/kasan/common.c:383
kmalloc include/linux/slab.h:580 [inline]
kzalloc include/linux/slab.h:720 [inline]
nfc_llcp_register_device+0x49/0xa40 net/nfc/llcp_core.c:1567
nfc_register_device+0x61/0x260 net/nfc/core.c:1124
nci_register_device+0x776/0xb20 net/nfc/nci/core.c:1257
virtual_ncidev_open+0x147/0x230 drivers/nfc/virtual_ncidev.c:148
misc_open+0x379/0x4a0 drivers/char/misc.c:165
chrdev_open+0x26c/0x780 fs/char_dev.c:414
do_dentry_open+0x6c4/0x12a0 fs/open.c:920
do_open fs/namei.c:3560 [inline]
path_openat+0x24fe/0x37e0 fs/namei.c:3715
do_filp_open+0x1ba/0x410 fs/namei.c:3742
do_sys_openat2+0x171/0x4c0 fs/open.c:1356
do_sys_open fs/open.c:1372 [inline]
__do_sys_openat fs/open.c:1388 [inline]
__se_sys_openat fs/open.c:1383 [inline]
__x64_sys_openat+0x143/0x200 fs/open.c:1383
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3f/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x72/0xdc
Freed by task 20115:
kasan_save_stack+0x22/0x50 mm/kasan/common.c:45
kasan_set_track+0x25/0x30 mm/kasan/common.c:52
kasan_save_free_info+0x2e/0x50 mm/kasan/generic.c:521
____kasan_slab_free mm/kasan/common.c:236 [inline]
____kasan_slab_free mm/kasan/common.c:200 [inline]
__kasan_slab_free+0x10a/0x190 mm/kasan/common.c:244
kasan_slab_free include/linux/kasan.h:162 [inline]
slab_free_hook mm/slub.c:1781 [inline]
slab_free_freelist_hook mm/slub.c:1807 [inline]
slab_free mm/slub.c:3787 [inline]
__kmem_cache_free+0x7a/0x190 mm/slub.c:3800
local_release net/nfc/llcp_core.c:174 [inline]
kref_put include/linux/kref.h:65 [inline]
nfc_llcp_local_put net/nfc/llcp_core.c:182 [inline]
nfc_llcp_local_put net/nfc/llcp_core.c:177 [inline]
nfc_llcp_unregister_device+0x206/0x290 net/nfc/llcp_core.c:1620
nfc_unregister_device+0x160/0x1d0 net/nfc/core.c:1179
virtual_ncidev_close+0x52/0xa0 drivers/nfc/virtual_ncidev.c:163
__fput+0x252/0xa20 fs/file_table.c:321
task_work_run+0x174/0x270 kernel/task_work.c:179
resume_user_mode_work include/linux/resume_user_mode.h:49 [inline]
exit_to_user_mode_loop kernel/entry/common.c:171 [inline]
exit_to_user_mode_prepare+0x108/0x110 kernel/entry/common.c:204
__syscall_exit_to_user_mode_work kernel/entry/common.c:286 [inline]
syscall_exit_to_user_mode+0x21/0x50 kernel/entry/common.c:297
do_syscall_64+0x4c/0x90 arch/x86/entry/common.c:86
entry_SYSCALL_64_after_hwframe+0x72/0xdc
Last potentially related work creation:
kasan_save_stack+0x22/0x50 mm/kasan/common.c:45
__kasan_record_aux_stack+0x95/0xb0 mm/kasan/generic.c:491
kvfree_call_rcu+0x29/0xa80 kernel/rcu/tree.c:3328
drop_sysctl_table+0x3be/0x4e0 fs/proc/proc_sysctl.c:1735
unregister_sysctl_table.part.0+0x9c/0x190 fs/proc/proc_sysctl.c:1773
unregister_sysctl_table+0x24/0x30 fs/proc/proc_sysctl.c:1753
neigh_sysctl_unregister+0x5f/0x80 net/core/neighbour.c:3895
addrconf_notify+0x140/0x17b0 net/ipv6/addrconf.c:3684
notifier_call_chain+0xbe/0x210 kernel/notifier.c:87
call_netdevice_notifiers_info+0xb5/0x150 net/core/dev.c:1937
call_netdevice_notifiers_extack net/core/dev.c:1975 [inline]
call_netdevice_notifiers net/core/dev.c:1989 [inline]
dev_change_name+0x3c3/0x870 net/core/dev.c:1211
dev_ifsioc+0x800/0xf70 net/core/dev_ioctl.c:376
dev_ioctl+0x3d9/0xf80 net/core/dev_ioctl.c:542
sock_do_ioctl+0x160/0x260 net/socket.c:1213
sock_ioctl+0x3f9/0x670 net/socket.c:1316
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:870 [inline]
__se_sys_ioctl fs/ioctl.c:856 [inline]
__x64_sys_ioctl+0x19e/0x210 fs/ioctl.c:856
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3f/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x72/0xdc
The buggy address belongs to the object at ffff888105b0e400
which belongs to the cache kmalloc-1k of size 1024
The buggy address is located 16 bytes inside of
freed 1024-byte region [ffff888105b0e400, ffff888105b0e800)
The buggy address belongs to the physical page:
head:ffffea000416c200 order:3 entire_mapcount:0 nr_pages_mapped:0 pincount:0
flags: 0x200000000010200(slab|head|node=0|zone=2)
raw: 0200000000010200 ffff8881000430c0 ffffea00044c7010 ffffea0004510e10
raw: 0000000000000000 00000000000a000a 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff888105b0e300: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff888105b0e380: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff888105b0e400: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff888105b0e480: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff888105b0e500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
In summary, this patch solves those use-after-free by
1. Re-implement the nfc_llcp_find_local(). The current version does not
grab the reference when getting the local from the linked list. For
example, the llcp_sock_bind() gets the reference like below:
// llcp_sock_bind()
local = nfc_llcp_find_local(dev); // A
..... \
| raceable
..... /
llcp_sock->local = nfc_llcp_local_get(local); // B
There is an apparent race window that one can drop the reference
and free the local object fetched in (A) before (B) gets the reference.
2. Some callers of the nfc_llcp_find_local() do not grab the reference
at all. For example, the nfc_genl_llc_{{get/set}_params/sdreq} functions.
We add the nfc_llcp_local_put() for them. Moreover, we add the necessary
error handling function to put the reference.
3. Add the nfc_llcp_remove_local() helper. The local object is removed
from the linked list in local_release() when all reference is gone. This
patch removes it when nfc_llcp_unregister_device() is called.
Therefore, every caller of nfc_llcp_find_local() will get a reference
even when the nfc_llcp_unregister_device() is called. This promises no
use-after-free for the local object is ever possible.
Fixes: 52feb444a9 ("NFC: Extend netlink interface for LTO, RW, and MIUX parameters support")
Fixes: c7aa12252f ("NFC: Take a reference on the LLCP local pointer when creating a socket")
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1b355438b ]
efx_net_stats() (.ndo_get_stats64) can be called during an ethtool
selftest, during which time nic_data->mc_stats is NULL as the NIC has
been fini'd. In this case do not attempt to fetch the latest stats
from the hardware, else we will crash on a NULL dereference:
BUG: kernel NULL pointer dereference, address: 0000000000000038
RIP efx_nic_update_stats
abridged calltrace:
efx_ef10_update_stats_pf
efx_net_stats
dev_get_stats
dev_seq_printf_stats
Skipping the read is safe, we will simply give out stale stats.
To ensure that the free in efx_ef10_fini_nic() does not race against
efx_ef10_update_stats_pf(), which could cause a TOCTTOU bug, take the
efx->stats_lock in fini_nic (it is already held across update_stats).
Fixes: d3142c193d ("sfc: refactor EF10 stats handling")
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1bc9fc4a0 ]
64-bit DMA detection will fail if axienet was started before (by boot
loader, boot ROM, etc). In this state axienet will not start properly.
XAXIDMA_TX_CDESC_OFFSET + 4 register (MM2S_CURDESC_MSB) is used to detect
64-bit DMA capability here. But datasheet says: When DMACR.RS is 1
(axienet is in enabled state), CURDESC_PTR becomes Read Only (RO) and
is used to fetch the first descriptor. So iowrite32()/ioread32() trick
to this register to detect 64-bit DMA will not work.
So move axienet reset before 64-bit DMA detection.
Fixes: f735c40ed9 ("net: axienet: Autodetect 64-bit DMA capability")
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Reviewed-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/20230622192245.116864-1-fido_max@inbox.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d61f926d4 ]
syzbot reported a possible deadlock in netlink_set_err() [1]
A similar issue was fixed in commit 1d482e666b ("netlink: disable IRQs
for netlink_lock_table()") in netlink_lock_table()
This patch adds IRQ safety to netlink_set_err() and __netlink_diag_dump()
which were not covered by cited commit.
[1]
WARNING: possible irq lock inversion dependency detected
6.4.0-rc6-syzkaller-00240-g4e9f0ec38852 #0 Not tainted
syz-executor.2/23011 just changed the state of lock:
ffffffff8e1a7a58 (nl_table_lock){.+.?}-{2:2}, at: netlink_set_err+0x2e/0x3a0 net/netlink/af_netlink.c:1612
but this lock was taken by another, SOFTIRQ-safe lock in the past:
(&local->queue_stop_reason_lock){..-.}-{2:2}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(nl_table_lock);
local_irq_disable();
lock(&local->queue_stop_reason_lock);
lock(nl_table_lock);
<Interrupt>
lock(&local->queue_stop_reason_lock);
*** DEADLOCK ***
Fixes: 1d482e666b ("netlink: disable IRQs for netlink_lock_table()")
Reported-by: syzbot+a7d200a347f912723e5c@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=a7d200a347f912723e5c
Link: https://lore.kernel.org/netdev/000000000000e38d1605fea5747e@google.com/T/#u
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20230621154337.1668594-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9fde4c557f ]
The Stuff Bit Count is always coded on 4 bits [1]. Update the Stuff
Bit Count size accordingly.
In addition, the CRC fields of CAN FD Frames contain stuff bits at
fixed positions called fixed stuff bits [2]. The CRC field starts with
a fixed stuff bit and then has another fixed stuff bit after each
fourth bit [2], which allows us to derive this formula:
FSB count = 1 + round_down(len(CRC field)/4)
The length of the CRC field is [1]:
len(CRC field) = len(Stuff Bit Count) + len(CRC)
= 4 + len(CRC)
with len(CRC) either 17 or 21 bits depending of the payload length.
In conclusion, for CRC17:
FSB count = 1 + round_down((4 + 17)/4)
= 6
and for CRC 21:
FSB count = 1 + round_down((4 + 21)/4)
= 7
Add a Fixed Stuff bits (FSB) field with above values and update
CANFD_FRAME_OVERHEAD_SFF and CANFD_FRAME_OVERHEAD_EFF accordingly.
[1] ISO 11898-1:2015 section 10.4.2.6 "CRC field":
The CRC field shall contain the CRC sequence followed by a recessive
CRC delimiter. For FD Frames, the CRC field shall also contain the
stuff count.
Stuff count
If FD Frames, the stuff count shall be at the beginning of the CRC
field. It shall consist of the stuff bit count modulo 8 in a 3-bit
gray code followed by a parity bit [...]
[2] ISO 11898-1:2015 paragraph 10.5 "Frame coding":
In the CRC field of FD Frames, the stuff bits shall be inserted at
fixed positions; they are called fixed stuff bits. There shall be a
fixed stuff bit before the first bit of the stuff count, even if the
last bits of the preceding field are a sequence of five consecutive
bits of identical value, there shall be only the fixed stuff bit,
there shall not be two consecutive stuff bits. A further fixed stuff
bit shall be inserted after each fourth bit of the CRC field [...]
Fixes: 85d99c3e2a ("can: length: can_skb_get_frame_len(): introduce function to get data length of frame in data link layer")
Suggested-by: Thomas Kopp <Thomas.Kopp@microchip.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Reviewed-by: Thomas Kopp <Thomas.Kopp@microchip.com>
Link: https://lore.kernel.org/all/20230611025728.450837-2-mailhol.vincent@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a5cb79762 ]
When calling bpf_sk_lookup_tcp(), bpf_sk_lookup_udp() or
bpf_skc_lookup_tcp() from tc/xdp ingress, VRF socket bindings aren't
respoected, i.e. unbound sockets are returned, and bound sockets aren't
found.
VRF binding is determined by the sdif argument to sk_lookup(), however
when called from tc the IP SKB control block isn't initialized and thus
inet{,6}_sdif() always returns 0.
Fix by calculating sdif for the tc/xdp flows by observing the device's
l3 enslaved state.
The cg/sk_skb hooking points which are expected to support
inet{,6}_sdif() pass sdif=-1 which makes __bpf_skc_lookup() use the
existing logic.
Fixes: 6acc9b432e ("bpf: Add helper to retrieve socket in BPF")
Signed-off-by: Gilad Sever <gilad9366@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Reviewed-by: Eyal Birger <eyal.birger@gmail.com>
Acked-by: Stanislav Fomichev <sdf@google.com>
Cc: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/bpf/20230621104211.301902-4-gilad9366@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e98730bc0 ]
Change BPF helper socket lookup functions to use TC specific variants:
bpf_tc_sk_lookup_tcp() / bpf_tc_sk_lookup_udp() / bpf_tc_skc_lookup_tcp()
instead of sharing implementation with the cg / sk_skb hooking points.
This allows introducing a separate logic for the TC flow.
The tc functions are identical to the original code.
Signed-off-by: Gilad Sever <gilad9366@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Reviewed-by: Eyal Birger <eyal.birger@gmail.com>
Acked-by: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/bpf/20230621104211.301902-2-gilad9366@gmail.com
Stable-dep-of: 9a5cb79762 ("bpf: Fix bpf socket lookup from tc/xdp to respect socket VRF bindings")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c467c8f081 ]
This microSD card never clears Flush Cache bit after cache flush has
been started in sd_flush_cache(). This leads e.g. to failure to mount
file system. Add a quirk which disables the SD cache for this specific
card from specific manufacturing date of 11/2019, since on newer dated
cards from 05/2023 the cache flush works correctly.
Fixes: 08ebf903af ("mmc: core: Fixup support for writeback-cache for eMMC and SD")
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20230620102713.7701-1-marex@denx.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39432f8a37 ]
The removed code ran for any BSS that was not included in the MBSSID
element in order to update it. However, instead of using the correct
inheritance rules, it would simply copy the elements from the
transmitting AP. The result is that we would report incorrect elements
in this case.
After some discussions, it seems that there are likely not even APs
actually using this feature. Either way, removing the code decreases
complexity and makes the cfg80211 behaviour more correct.
Fixes: 0b8fb8235b ("cfg80211: Parsing of Multiple BSSID information in scanning")
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230616094949.cfd6d8db1f26.Ia1044902b86cd7d366400a4bfb93691b8f05d68c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dfd9aa3e7a ]
The cfg80211_gen_new_ie function merges the IEs using inheritance rules.
Rewrite this function to fix issues around inheritance rules. In
particular, vendor elements do not require any special handling, as they
are either all inherited or overridden by the subprofile.
Also, add fragmentation handling as this may be needed in some cases.
This also changes the function to not require making a copy. The new
version could be optimized a bit by explicitly tracking which IEs have
been handled already rather than looking that up again every time.
Note that a small behavioural change is the removal of the SSID special
handling. This should be fine for the MBSSID element, as the SSID must
be included in the subelement.
Fixes: 0b8fb8235b ("cfg80211: Parsing of Multiple BSSID information in scanning")
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230616094949.bc6152e146db.I2b5f3bc45085e1901e5b5192a674436adaf94748@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa0e21fa44 ]
This filter already exists for excluding IPv6 SNMP stats. Extend its
definition to also exclude IFLA_VF_INFO stats in RTM_GETLINK.
This patch constitutes a partial fix for a netlink attribute nesting
overflow bug in IFLA_VFINFO_LIST. By excluding the stats when the
requester doesn't need them, the truncation of the VF list is avoided.
While it was technically only the stats added in commit c5a9f6f0ab
("net/core: Add drop counters to VF statistics") breaking the camel's
back, the appreciable size of the stats data should never have been
included without due consideration for the maximum number of VFs
supported by PCI.
Fixes: 3b766cd832 ("net/core: Add reading VF statistics through the PF netdevice")
Fixes: c5a9f6f0ab ("net/core: Add drop counters to VF statistics")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Cc: Edwin Peer <espeer@gmail.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Link: https://lore.kernel.org/r/20230611105108.122586-1-gal@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75086cc6de ]
On EDMA capable hardware, ath9k_txq_list_has_key() can enter infinite
loop if it is called while all txq_fifos have packets that use different
key that the one we are looking for. Fix it by exiting the loop if all
txq_fifos have been checked already.
Because this loop is called under spin_lock_bh() (see ath_txq_lock) it
causes the following rcu stall:
rcu: INFO: rcu_sched self-detected stall on CPU
ath10k_pci 0000:01:00.0: failed to read temperature -11
rcu: 1-....: (5254 ticks this GP) idle=189/1/0x4000000000000002 softirq=8442983/8442984 fqs=2579
(t=5257 jiffies g=17983297 q=334)
Task dump for CPU 1:
task:hostapd state:R running task stack: 0 pid: 297 ppid: 289 flags:0x0000000a
Call trace:
dump_backtrace+0x0/0x170
show_stack+0x1c/0x24
sched_show_task+0x140/0x170
dump_cpu_task+0x48/0x54
rcu_dump_cpu_stacks+0xf0/0x134
rcu_sched_clock_irq+0x8d8/0x9fc
update_process_times+0xa0/0xec
tick_sched_timer+0x5c/0xd0
__hrtimer_run_queues+0x154/0x320
hrtimer_interrupt+0x120/0x2f0
arch_timer_handler_virt+0x38/0x44
handle_percpu_devid_irq+0x9c/0x1e0
handle_domain_irq+0x64/0x90
gic_handle_irq+0x78/0xb0
call_on_irq_stack+0x28/0x38
do_interrupt_handler+0x54/0x5c
el1_interrupt+0x2c/0x4c
el1h_64_irq_handler+0x14/0x1c
el1h_64_irq+0x74/0x78
ath9k_txq_has_key+0x1bc/0x250 [ath9k]
ath9k_set_key+0x1cc/0x3dc [ath9k]
drv_set_key+0x78/0x170
ieee80211_key_replace+0x564/0x6cc
ieee80211_key_link+0x174/0x220
ieee80211_add_key+0x11c/0x300
nl80211_new_key+0x12c/0x330
genl_family_rcv_msg_doit+0xbc/0x11c
genl_rcv_msg+0xd8/0x1c4
netlink_rcv_skb+0x40/0x100
genl_rcv+0x3c/0x50
netlink_unicast+0x1ec/0x2c0
netlink_sendmsg+0x198/0x3c0
____sys_sendmsg+0x210/0x250
___sys_sendmsg+0x78/0xc4
__sys_sendmsg+0x4c/0x90
__arm64_sys_sendmsg+0x28/0x30
invoke_syscall.constprop.0+0x60/0x100
do_el0_svc+0x48/0xd0
el0_svc+0x14/0x50
el0t_64_sync_handler+0xa8/0xb0
el0t_64_sync+0x158/0x15c
This rcu stall is hard to reproduce as is, but changing ATH_TXFIFO_DEPTH
from 8 to 2 makes it reasonably easy to reproduce.
Fixes: ca2848022c ("ath9k: Postpone key cache entry deletion for TXQ frames reference it")
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Tested-by: Nicolas Escande <nico.escande@gmail.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230609093744.1985-1-repk@triplefau.lt
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b23ed4d74c ]
Dan Carpenter reported invalid check for calloc() result in
test_verifier.c:get_xlated_program():
./tools/testing/selftests/bpf/test_verifier.c:1365 get_xlated_program()
warn: variable dereferenced before check 'buf' (see line 1364)
./tools/testing/selftests/bpf/test_verifier.c
1363 *cnt = xlated_prog_len / buf_element_size;
1364 *buf = calloc(*cnt, buf_element_size);
1365 if (!buf) {
This should be if (!*buf) {
1366 perror("can't allocate xlated program buffer");
1367 return -ENOMEM;
This commit refactors the get_xlated_program() to avoid using double
pointer type.
Fixes: 933ff53191 ("selftests/bpf: specify expected instructions in test_verifier tests")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Closes: https://lore.kernel.org/bpf/ZH7u0hEGVB4MjGZq@moroto/
Link: https://lore.kernel.org/bpf/20230609221637.2631800-1-eddyz87@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 434587df9f ]
There are no other files referencing this function, apparently
it was left global to avoid an 'unused function' warning when
the only caller is left out. With a 'W=1' build, it causes
a 'missing prototype' warning though:
drivers/memstick/host/r592.c:47:13: error: no previous prototype for 'memstick_debug_get_tpc_name' [-Werror=missing-prototypes]
Annotate the function as 'static __maybe_unused' to avoid both
problems.
Fixes: 9263412501 ("memstick: add driver for Ricoh R5C592 card reader")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230516202714.560929-1-arnd@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1cba6c4309 ]
Patch series "kexec: enable kexec_crash_size to support two crash kernel
regions".
When crashkernel=X fails to reserve region under 4G, it will fall back to
reserve region above 4G and a region of the default size will also be
reserved under 4G. Unfortunately, /sys/kernel/kexec_crash_size only
supports one crash kernel region now, the user cannot sense the low memory
reserved by reading /sys/kernel/kexec_crash_size. Also, low memory cannot
be freed by writing this file.
For example:
resource_size(crashk_res) = 512M
resource_size(crashk_low_res) = 256M
The result of 'cat /sys/kernel/kexec_crash_size' is 512M, but it should be
768M. When we execute 'echo 0 > /sys/kernel/kexec_crash_size', the size
of crashk_res becomes 0 and resource_size(crashk_low_res) is still 256 MB,
which is incorrect.
Since crashk_res manages the memory with high address and crashk_low_res
manages the memory with low address, crashk_low_res is shrunken only when
all crashk_res is shrunken. And because when there is only one crash
kernel region, crashk_res is always used. Therefore, if all crashk_res is
shrunken and crashk_low_res still exists, swap them.
This patch (of 6):
If the value of parameter 'new_size' is in the semi-open and semi-closed
interval (crashk_res.end - KEXEC_CRASH_MEM_ALIGN + 1, crashk_res.end], the
calculation result of ram_res is:
ram_res->start = crashk_res.end + 1
ram_res->end = crashk_res.end
The operation of insert_resource() fails, and ram_res is not added to
iomem_resource. As a result, the memory of the control block ram_res is
leaked.
In fact, on all architectures, the start address and size of crashk_res
are already aligned by KEXEC_CRASH_MEM_ALIGN. Therefore, we do not need
to round up crashk_res.start again. Instead, we should round up
'new_size' in advance.
Link: https://lkml.kernel.org/r/20230527123439.772-1-thunder.leizhen@huawei.com
Link: https://lkml.kernel.org/r/20230527123439.772-2-thunder.leizhen@huawei.com
Fixes: 6480e5a092 ("kdump: add missing RAM resource in crash_shrink_memory()")
Fixes: 06a7f71124 ("kexec: premit reduction of the reserved memory size")
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Acked-by: Baoquan He <bhe@redhat.com>
Cc: Cong Wang <amwang@redhat.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e8b2c88fc ]
The ice_ptp_extts_work() and ice_ptp_periodic_work() functions are both
scheduled on the same kthread worker, pf.ptp.kworker. The
ice_ptp_periodic_work() function sends to the firmware to interact with the
PHY, and must block to wait for responses.
This can cause delay in responding to the PFINT_OICR_TSYN_EVNT interrupt
cause, ultimately resulting in disruption to processing an input signal of
the frequency is high enough. In our testing, even 100 Hz signals get
disrupted.
Fix this by instead processing the signal inside the miscellaneous
interrupt thread prior to handling Tx timestamps.
Use atomic bits in a new pf->misc_thread bitmap in order to safely
communicate which tasks require processing within the
ice_misc_intr_thread_fn(). This ensures the communication of desired tasks
from the ice_misc_intr() are correctly processed without racing even in the
event that the interrupt triggers again before the thread function exits.
Fixes: 172db5f91d ("ice: add support for auxiliary input/output pins")
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b241e26082 ]
In case WoWlan was never configured during the operation of the system,
the hw->wiphy->wowlan_config will be NULL. rsi_config_wowlan() checks
whether wowlan_config is non-NULL and if it is not, then WARNs about it.
The warning is valid, as during normal operation the rsi_config_wowlan()
should only ever be called with non-NULL wowlan_config. In shutdown this
rsi_config_wowlan() should only ever be called if WoWlan was configured
before by the user.
Add checks for non-NULL wowlan_config into the shutdown hook. While at it,
check whether the wiphy is also non-NULL before accessing wowlan_config .
Drop the single-use wowlan_config variable, just inline it into function
call.
Fixes: 16bbc3eb83 ("rsi: fix null pointer dereference during rsi_shutdown()")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230527222833.273741-1-marex@denx.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit edd75c8028 ]
Building BPF selftests with custom HOSTCFLAGS yields an error:
# make HOSTCFLAGS="-O2"
[...]
HOSTCC ./tools/testing/selftests/bpf/tools/build/resolve_btfids/main.o
main.c:73:10: fatal error: linux/rbtree.h: No such file or directory
73 | #include <linux/rbtree.h>
| ^~~~~~~~~~~~~~~~
The reason is that tools/bpf/resolve_btfids/Makefile passes header
include paths by extending HOSTCFLAGS which is overridden by setting
HOSTCFLAGS in the make command (because of Makefile rules [1]).
This patch fixes the above problem by passing the include paths via
`HOSTCFLAGS_resolve_btfids` which is used by tools/build/Build.include
and can be combined with overridding HOSTCFLAGS.
[1] https://www.gnu.org/software/make/manual/html_node/Overriding.html
Fixes: 56a2df7615 ("tools/resolve_btfids: Compile resolve_btfids as host program")
Signed-off-by: Viktor Malik <vmalik@redhat.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/bpf/20230530123352.1308488-1-vmalik@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75bd32f5ce ]
Currently, on WCN3990, the station disconnect after hardware recovery is
not working as expected. This is because of setting the
IEEE80211_SDATA_DISCONNECT_HW_RESTART flag very early in the hardware
recovery process even before the driver invokes ieee80211_hw_restart().
On the contrary, mac80211 expects this flag to be set after
ieee80211_hw_restart() is invoked for it to trigger station disconnect.
Set the IEEE80211_SDATA_DISCONNECT_HW_RESTART flag in
ath10k_reconfig_complete() instead to fix this.
The other targets are not affected by this change, since the hardware
params flag is not set.
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.2.2.c10-00754-QCAHLSWMTPL-1
Fixes: 2c3fc50591 ("ath10k: Trigger sta disconnect on hardware restart")
Signed-off-by: Youghandhar Chintala <quic_youghand@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230518101515.3820-1-quic_youghand@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60548b825b ]
Default samples/pktgen scripts send 60 byte packets as hardware adds
4-bytes FCS checksum, which fulfils minimum Ethernet 64 bytes frame
size.
XDP layer will not necessary have access to the 4-bytes FCS checksum.
This leads to bpf_xdp_load_bytes() failing as it tries to copy 64-bytes
from an XDP packet that only have 60-bytes available.
Fixes: 7722517422 ("samples/bpf: fixup some tools to be able to support xdp multibuffer")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/bpf/168545704139.2996228.2516528552939485216.stgit@firesoul
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f1784a59c ]
When receiving more rx packets than the kernel can handle the driver
drops the packets and issues an error message. This is bad for two
reasons. The logs are flooded with myriads of messages, but then time
consumed for printing messages in that critical code path brings down
the device. After some time of excessive rx load the driver responds
with:
rtw_8822cu 1-1:1.2: failed to get tx report from firmware
rtw_8822cu 1-1:1.2: firmware failed to report density after scan
rtw_8822cu 1-1:1.2: firmware failed to report density after scan
The device stops working until being replugged.
Fix this by lowering the priority to debug level and also by
ratelimiting it.
Fixes: a82dfd33d1 ("wifi: rtw88: Add common USB chip support")
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230524103934.1019096-1-s.hauer@pengutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08880713ce ]
If CONFIG_DEBUG_FS is not set:
regulator: Failed to create debugfs directory
...
regulator-dummy: Failed to create debugfs directory
As per the comments for debugfs_create_dir(), errors returned by this
function should be expected, and ignored:
* If debugfs is not enabled in the kernel, the value -%ENODEV will be
* returned.
*
* NOTE: it's expected that most callers should _ignore_ the errors returned
* by this function. Other debugfs functions handle the fact that the "dentry"
* passed to them could be an error and they don't crash in that case.
* Drivers should generally work fine even if debugfs fails to init anyway.
Adhere to the debugfs spirit, and streamline all operations by:
1. Demoting the importance of the printed error messages to debug
level, like is already done in create_regulator(),
2. Further ignoring any returned errors, as by design, all debugfs
functions are no-ops when passed an error pointer.
Fixes: 2bf1c45be3 ("regulator: Fix error checking for debugfs_create_dir")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/2f8bb6e113359ddfab7b59e4d4274bd4c06d6d0a.1685013051.git.geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f04a32b2c5 ]
The sign-file utility (from scripts/) is used in prog_tests/verify_pkcs7_sig.c,
but the utility should not be called as a test. Executing this utility produces
the following error:
selftests: /linux/tools/testing/selftests/bpf: urandom_read
ok 16 selftests: /linux/tools/testing/selftests/bpf: urandom_read
selftests: /linux/tools/testing/selftests/bpf: sign-file
not ok 17 selftests: /linux/tools/testing/selftests/bpf: sign-file # exit=2
Also, urandom_read is mistakenly used as a test. It does not lead to an error,
but should be moved over to TEST_GEN_FILES as well. The empty TEST_CUSTOM_PROGS
can then be removed.
Fixes: fc97590668 ("selftests/bpf: Add test for bpf_verify_pkcs7_signature() kfunc")
Signed-off-by: Alexey Gladkov <legion@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Roberto Sassu <roberto.sassu@huawei.com>
Acked-by: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/bpf/ZEuWFk3QyML9y5QQ@example.org
Link: https://lore.kernel.org/bpf/88e3ab23029d726a2703adcf6af8356f7a2d3483.1684316821.git.legion@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 108598c39e ]
If it fails to attach fentry, the allocated bpf trampoline image will be
left in the system. That can be verified by checking /proc/kallsyms.
This meamleak can be verified by a simple bpf program as follows:
SEC("fentry/trap_init")
int fentry_run()
{
return 0;
}
It will fail to attach trap_init because this function is freed after
kernel init, and then we can find the trampoline image is left in the
system by checking /proc/kallsyms.
$ tail /proc/kallsyms
ffffffffc0613000 t bpf_trampoline_6442453466_1 [bpf]
ffffffffc06c3000 t bpf_trampoline_6442453466_1 [bpf]
$ bpftool btf dump file /sys/kernel/btf/vmlinux | grep "FUNC 'trap_init'"
[2522] FUNC 'trap_init' type_id=119 linkage=static
$ echo $((6442453466 & 0x7fffffff))
2522
Note that there are two left bpf trampoline images, that is because the
libbpf will fallback to raw tracepoint if -EINVAL is returned.
Fixes: e21aa34178 ("bpf: Fix fexit trampoline.")
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <song@kernel.org>
Cc: Jiri Olsa <olsajiri@gmail.com>
Link: https://lore.kernel.org/bpf/20230515130849.57502-2-laoar.shao@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47e79cbeea ]
After commit e21aa34178 ("bpf: Fix fexit trampoline."), the selector is only
used to indicate how many times the bpf trampoline image are updated and been
displayed in the trampoline ksym name. After the trampoline is freed, the
selector will start from 0 again. So the selector is a useless value to the
user. We can remove it.
If the user want to check whether the bpf trampoline image has been updated
or not, the user can compare the address. Each time the trampoline image is
updated, the address will change consequently. Jiri also pointed out another
issue that perf is still using the old name "bpf_trampoline_%lu", so this
change can fix the issue in perf.
Fixes: e21aa34178 ("bpf: Fix fexit trampoline.")
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <song@kernel.org>
Cc: Jiri Olsa <olsajiri@gmail.com>
Link: https://lore.kernel.org/bpf/ZFvOOlrmHiY9AgXE@krava
Link: https://lore.kernel.org/bpf/20230515130849.57502-3-laoar.shao@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04cb8453a9 ]
On aarch64, "bpftool feature" reports an incorrect BPF JIT limit:
$ sudo /sbin/bpftool feature
Scanning system configuration...
bpf() syscall restricted to privileged users
JIT compiler is enabled
JIT compiler hardening is disabled
JIT compiler kallsyms exports are enabled for root
skipping kernel config, can't open file: No such file or directory
Global memory limit for JIT compiler for unprivileged users is -201326592 bytes
This is because /proc/sys/net/core/bpf_jit_limit reports
$ sudo cat /proc/sys/net/core/bpf_jit_limit
68169519595520
...and an int is assumed in read_procfs(). Change read_procfs()
to return a long to avoid negative value reporting.
Fixes: 7a4522bbef ("tools: bpftool: add probes for /proc/ eBPF parameters")
Reported-by: Nicky Veitch <nicky.veitch@oracle.com>
Signed-off-by: Alan Maguire <alan.maguire@oracle.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Quentin Monnet <quentin@isovalent.com>
Link: https://lore.kernel.org/bpf/20230512113134.58996-1-alan.maguire@oracle.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d9b41daa5 ]
If sock->service_name is NULL, the local variable
service_name_tlv_length will not be assigned by nfc_llcp_build_tlv(),
later leading to using value frmo the stack. Smatch warning:
net/nfc/llcp_commands.c:442 nfc_llcp_send_connect() error: uninitialized symbol 'service_name_tlv_length'.
Fixes: de9e5aeb4f ("NFC: llcp: Fix usage of llcp_add_tlv()")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f34baf67e ]
n_bytes variable in the driver represents the number of bytes per word
that needs to be sent/copied to fifo. Bits/word can be between 8 and 32
bits from the client but in memory they are a power of 2, same is mentioned
in spi.h header:
"
* @bits_per_word: Data transfers involve one or more words; word sizes
* like eight or 12 bits are common. In-memory wordsizes are
* powers of two bytes (e.g. 20 bit samples use 32 bits).
* This may be changed by the device's driver, or left at the
* default (0) indicating protocol words are eight bit bytes.
* The spi_transfer.bits_per_word can override this for each transfer.
"
Hence, round of n_bytes to a power of 2 to avoid values like 3 which
would generate unalligned/odd accesses to memory/fifo.
* tested on Baikal-T1 based system with DW SPI-looped back interface
transferring a chunk of data with DFS:8,12,16.
Fixes: a51acc2400 ("spi: dw: Add support for 32-bits max xfer size")
Suggested-by: Andy Shevchenko <andriy.shevchenko@intel.com
Signed-off-by: Joy Chakraborty <joychakr@google.com
Reviewed-by: Serge Semin <fancer.lancer@gmail.com
Tested-by: Serge Semin <fancer.lancer@gmail.com
Link: https://lore.kernel.org/r/20230512104746.1797865-4-joychakr@google.com
Signed-off-by: Mark Brown <broonie@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 29ebbba7d4 ]
With the way the hooks implemented right now, we have a special
condition: optval larger than PAGE_SIZE will expose only first 4k into
BPF; any modifications to the optval are ignored. If the BPF program
doesn't handle this condition by resetting optlen to 0,
the userspace will get EFAULT.
The intention of the EFAULT was to make it apparent to the
developers that the program is doing something wrong.
However, this inadvertently might affect production workloads
with the BPF programs that are not too careful (i.e., returning EFAULT
for perfectly valid setsockopt/getsockopt calls).
Let's try to minimize the chance of BPF program screwing up userspace
by ignoring the output of those BPF programs (instead of returning
EFAULT to the userspace). pr_info_once those cases to
the dmesg to help with figuring out what's going wrong.
Fixes: 0d01da6afc ("bpf: implement getsockopt and setsockopt hooks")
Suggested-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/r/20230511170456.1759459-2-sdf@google.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bdeeed3498 ]
It seems like __builtin_offset() doesn't preserve CO-RE field
relocations properly. So if offsetof() macro is defined through
__builtin_offset(), CO-RE-enabled BPF code using container_of() will be
subtly and silently broken.
To avoid this problem, redefine offsetof() and container_of() in the
form that works with CO-RE relocations more reliably.
Fixes: 5fbc220862 ("tools/libpf: Add offsetof/container_of macro in bpf_helpers.h")
Reported-by: Lennart Poettering <lennart@poettering.net>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/r/20230509065502.2306180-1-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ce4bb0912 ]
Mandatory WFA testcase
CT_Security_WPA2Personal_STA_RSNEBoundsVerification-AbsentRSNCap,
performs bounds verfication on Beacon and/or Probe response frames. It
failed and observed the reason to be absence of cipher suite and AKM
suite in RSN information. To fix this, enable the RSN flag before extracting RSN
capabilities.
Fixes: cd21d99e59 ("wifi: wilc1000: validate pairwise and authentication suite offsets")
Signed-off-by: Amisha Patel <amisha.patel@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230421181005.4865-1-amisha.patel@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c39028b333 ]
The btf_dump/struct_data selftest is failing with:
[...]
test_btf_dump_struct_data:FAIL:unexpected return value dumping fs_context unexpected unexpected return value dumping fs_context: actual -7 != expected 264
[...]
The reason is in btf_dump_type_data_check_overflow(). It does not use
BTF_MEMBER_BITFIELD_SIZE from the struct's member (btf_member). Instead,
it is using the enum size which is 4. It had been working till the recent
commit 4e04143c86 ("fs_context: drop the unused lsm_flags member")
removed an integer member which also removed the 4 bytes padding at the
end of the fs_context. Missing this 4 bytes padding exposed this bug. In
particular, when btf_dump_type_data_check_overflow() reaches the member
'phase', -E2BIG is returned.
The fix is to pass bit_sz to btf_dump_type_data_check_overflow(). In
btf_dump_type_data_check_overflow(), it does a different size check when
bit_sz is not zero.
The current fs_context:
[3600] ENUM 'fs_context_purpose' encoding=UNSIGNED size=4 vlen=3
'FS_CONTEXT_FOR_MOUNT' val=0
'FS_CONTEXT_FOR_SUBMOUNT' val=1
'FS_CONTEXT_FOR_RECONFIGURE' val=2
[3601] ENUM 'fs_context_phase' encoding=UNSIGNED size=4 vlen=7
'FS_CONTEXT_CREATE_PARAMS' val=0
'FS_CONTEXT_CREATING' val=1
'FS_CONTEXT_AWAITING_MOUNT' val=2
'FS_CONTEXT_AWAITING_RECONF' val=3
'FS_CONTEXT_RECONF_PARAMS' val=4
'FS_CONTEXT_RECONFIGURING' val=5
'FS_CONTEXT_FAILED' val=6
[3602] STRUCT 'fs_context' size=264 vlen=21
'ops' type_id=3603 bits_offset=0
'uapi_mutex' type_id=235 bits_offset=64
'fs_type' type_id=872 bits_offset=1216
'fs_private' type_id=21 bits_offset=1280
'sget_key' type_id=21 bits_offset=1344
'root' type_id=781 bits_offset=1408
'user_ns' type_id=251 bits_offset=1472
'net_ns' type_id=984 bits_offset=1536
'cred' type_id=1785 bits_offset=1600
'log' type_id=3621 bits_offset=1664
'source' type_id=42 bits_offset=1792
'security' type_id=21 bits_offset=1856
's_fs_info' type_id=21 bits_offset=1920
'sb_flags' type_id=20 bits_offset=1984
'sb_flags_mask' type_id=20 bits_offset=2016
's_iflags' type_id=20 bits_offset=2048
'purpose' type_id=3600 bits_offset=2080 bitfield_size=8
'phase' type_id=3601 bits_offset=2088 bitfield_size=8
'need_free' type_id=67 bits_offset=2096 bitfield_size=1
'global' type_id=67 bits_offset=2097 bitfield_size=1
'oldapi' type_id=67 bits_offset=2098 bitfield_size=1
Fixes: 920d16af9b ("libbpf: BTF dumper support for typed data")
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20230428013638.1581263-1-martin.lau@linux.dev
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f24292e827 ]
For the reasons also described in commit b383e8abed ("wifi: ath9k: avoid
uninit memory read in ath9k_htc_rx_msg()"), ath9k_htc_rx_msg() should
validate pkt_len before accessing the SKB.
For example, the obtained SKB may have been badly constructed with
pkt_len = 8. In this case, the SKB can only contain a valid htc_frame_hdr
but after being processed in ath9k_htc_rx_msg() and passed to
ath9k_wmi_ctrl_rx() endpoint RX handler, it is expected to have a WMI
command header which should be located inside its data payload.
Implement sanity checking inside ath9k_wmi_ctrl_rx(). Otherwise, uninit
memory can be referenced.
Tested on Qualcomm Atheros Communications AR9271 802.11n .
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: fb9987d0f7 ("ath9k_htc: Support for AR9271 chipset.")
Reported-and-tested-by: syzbot+f2cb6e0ffdb961921e4d@syzkaller.appspotmail.com
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230424183348.111355-1-pchelkin@ispras.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84214ab468 ]
When function igc_rx_hash() was introduced in v4.20 via commit 0507ef8a03
("igc: Add transmit and receive fastpath and interrupt handlers"), the
hardware wasn't configured to provide RSS hash, thus it made sense to not
enable net_device NETIF_F_RXHASH feature bit.
The NIC hardware was configured to enable RSS hash info in v5.2 via commit
2121c2712f ("igc: Add multiple receive queues control supporting"), but
forgot to set the NETIF_F_RXHASH feature bit.
The original implementation of igc_rx_hash() didn't extract the associated
pkt_hash_type, but statically set PKT_HASH_TYPE_L3. The largest portions of
this patch are about extracting the RSS Type from the hardware and mapping
this to enum pkt_hash_types. This was based on Foxville i225 software user
manual rev-1.3.1 and tested on Intel Ethernet Controller I225-LM (rev 03).
For UDP it's worth noting that RSS (type) hashing have been disabled both for
IPv4 and IPv6 (see IGC_MRQC_RSS_FIELD_IPV4_UDP + IGC_MRQC_RSS_FIELD_IPV6_UDP)
because hardware RSS doesn't handle fragmented pkts well when enabled (can
cause out-of-order). This results in PKT_HASH_TYPE_L3 for UDP packets, and
hash value doesn't include UDP port numbers. Not being PKT_HASH_TYPE_L4, have
the effect that netstack will do a software based hash calc calling into
flow_dissect, but only when code calls skb_get_hash(), which doesn't
necessary happen for local delivery.
For QA verification testing I wrote a small bpftrace prog:
[0] https://github.com/xdp-project/xdp-project/blob/master/areas/hints/monitor_skb_hash_on_dev.bt
Fixes: 2121c2712f ("igc: Add multiple receive queues control supporting")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Yoong Siang <yoong.siang.song@intel.com>
Link: https://lore.kernel.org/bpf/168182464270.616355.11391652654430626584.stgit@firesoul
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ebb83d84e4 ]
After commit 8ad075c2eb ("sched: Async unthrottling for cfs
bandwidth"), we may update the rq clock multiple times in the loop of
__cfsb_csd_unthrottle().
A prior (although less common) instance of this problem exists in
unthrottle_offline_cfs_rqs().
Cure both by ensuring update_rq_clock() is called before the loop and
setting RQCF_ACT_SKIP during the loop, to supress further updates.
The alternative would be pulling update_rq_clock() out of
unthrottle_cfs_rq(), but that gives an even bigger mess.
Fixes: 8ad075c2eb ("sched: Async unthrottling for cfs bandwidth")
Reviewed-By: Ben Segall <bsegall@google.com>
Suggested-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Hao Jia <jiahao.os@bytedance.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Vincent Guittot <vincent.guittot@linaro.org>
Link: https://lkml.kernel.org/r/20230613082012.49615-4-jiahao.os@bytedance.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dda5f312bb ]
The sync_*() ops on arch/arm are defined in terms of the regular bitops
with no special handling. This is not correct, as UP kernels elide
barriers for the fully-ordered operations, and so the required ordering
is lost when such UP kernels are run under a hypervsior on an SMP
system.
Fix this by defining sync ops with the required barriers.
Note: On 32-bit arm, the sync_*() ops are currently only used by Xen,
which requires ARMv7, but the semantics can be implemented for ARMv6+.
Fixes: e54d2f6152 ("xen/arm: sync_bitops")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230605070124.3741859-2-mark.rutland@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f88130e8a ]
Normally __swp_entry_to_pte() is never called with a value translating
to a valid PTE. The only known exception is pte_swap_tests(), resulting
in a WARN splat in Xen PV guests, as __pte_to_swp_entry() did
translate the PFN of the valid PTE to a guest local PFN, while
__swp_entry_to_pte() doesn't do the opposite translation.
Fix that by using __pte() in __swp_entry_to_pte() instead of open
coding the native variant of it.
For correctness do the similar conversion for __swp_entry_to_pmd().
Fixes: 05289402d7 ("mm/debug_vm_pgtable: add tests validating arch helpers for core MM features")
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20230306123259.12461-1-jgross@suse.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2fad201fe3 ]
Although, IBS pmus can be invoked via their own interface, indirect
IBS invocation via core pmu events is also supported with fixed set
of events: cpu-cycles:p, r076:p (same as cpu-cycles:p) and r0C1:p
(micro-ops) for user convenience.
This indirect IBS invocation is broken since commit 66d258c5b0
("perf/core: Optimize perf_init_event()"), which added RAW pmu under
'pmu_idr' list and thus if event_init() fails with RAW pmu, it started
returning error instead of trying other pmus.
Forward precise events from core pmu to IBS by overwriting 'type' and
'config' in the kernel copy of perf_event_attr. Overwriting will cause
perf_init_event() to retry with updated 'type' and 'config', which will
automatically forward event to IBS pmu.
Without patch:
$ sudo ./perf record -C 0 -e r076:p -- sleep 1
Error:
The r076:p event is not supported.
With patch:
$ sudo ./perf record -C 0 -e r076:p -- sleep 1
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.341 MB perf.data (37 samples) ]
Fixes: 66d258c5b0 ("perf/core: Optimize perf_init_event()")
Reported-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Ravi Bangoria <ravi.bangoria@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20230504110003.2548-3-ravi.bangoria@amd.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 375b9ff53c ]
In the unlikely case that CLOCK_REALTIME is not defined, variable ret is
not initialized and further accumulation of return values to ret can leave
ret in an undefined state. Fix this by initialized ret to zero and changing
the assignment of ret to an accumulation for the CLOCK_REALTIME case.
Fixes: 03f55c7952 ("kselftest: Extend vDSO selftest to clock_getres")
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a153f254e5 ]
When running as Xen PV initial domain (aka dom0), MTRRs are disabled
by the hypervisor, but the system should nevertheless use correct
cache memory types. This has always kind of worked, as disabled MTRRs
resulted in disabled PAT, too, so that the kernel avoided code paths
resulting in inconsistencies. This bypassed all of the sanity checks
the kernel is doing with enabled MTRRs in order to avoid memory
mappings with conflicting memory types.
This has been changed recently, leading to PAT being accepted to be
enabled, while MTRRs stayed disabled. The result is that
mtrr_type_lookup() no longer is accepting all memory type requests,
but started to return WB even if UC- was requested. This led to
driver failures during initialization of some devices.
In reality MTRRs are still in effect, but they are under complete
control of the Xen hypervisor. It is possible, however, to retrieve
the MTRR settings from the hypervisor.
In order to fix those problems, overwrite the MTRR state via
mtrr_overwrite_state() with the MTRR data from the hypervisor, if the
system is running as a Xen dom0.
Fixes: 72cbc8f04f ("x86/PAT: Have pat_enabled() properly reflect state when running on Xen")
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Tested-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20230502120931.20719-6-jgross@suse.com
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 29055dc742 ]
When running virtualized, MTRR access can be reduced (e.g. in Xen PV
guests or when running as a SEV-SNP guest under Hyper-V). Typically, the
hypervisor will not advertize the MTRR feature in CPUID data, resulting
in no MTRR memory type information being available for the kernel.
This has turned out to result in problems (Link tags below):
- Hyper-V SEV-SNP guests using uncached mappings where they shouldn't
- Xen PV dom0 mapping memory as WB which should be UC- instead
Solve those problems by allowing an MTRR static state override,
overwriting the empty state used today. In case such a state has been
set, don't call get_mtrr_state() in mtrr_bp_init().
The set state will only be used by mtrr_type_lookup(), as in all other
cases mtrr_enabled() is being checked, which will return false. Accept
the overwrite call only for selected cases when running as a guest.
Disable X86_FEATURE_MTRR in order to avoid any MTRR modifications by
just refusing them.
[ bp: Massage. ]
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Tested-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/all/4fe9541e-4d4c-2b2a-f8c8-2d34a7284930@nerdbynature.de/
Link: https://lore.kernel.org/lkml/BYAPR21MB16883ABC186566BD4D2A1451D7FE9@BYAPR21MB1688.namprd21.prod.outlook.com
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Stable-dep-of: a153f254e5 ("x86/xen: Set MTRR state when running as Xen PV initial domain")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d053b481a5 ]
Replace size_or_mask and size_and_mask with the much easier concept of
high reserved bits.
While at it, instead of using constants in the MTRR code, use some new
[ bp:
- Drop mtrr_set_mask()
- Unbreak long lines
- Move struct mtrr_state_type out of the uapi header as it doesn't
belong there. It also fixes a HDRTEST breakage "unknown type name ‘bool’"
as Reported-by: kernel test robot <lkp@intel.com>
- Massage.
]
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20230502120931.20719-3-jgross@suse.com
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Stable-dep-of: a153f254e5 ("x86/xen: Set MTRR state when running as Xen PV initial domain")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6b980646b ]
The physical address width calculation in mtrr_bp_init() can easily be
replaced with using the already available value x86_phys_bits from
struct cpuinfo_x86.
The same information source can be used in mtrr/cleanup.c, removing the
need to pass that value on to mtrr_cleanup().
In print_mtrr_state() use x86_phys_bits instead of recalculating it
from size_or_mask.
Move setting of size_or_mask and size_and_mask into a dedicated new
function in mtrr/generic.c, enabling to make those 2 variables static,
as they are used in generic.c only now.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Tested-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20230502120931.20719-2-jgross@suse.com
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Stable-dep-of: a153f254e5 ("x86/xen: Set MTRR state when running as Xen PV initial domain")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf5ddd7365 ]
This code-movement-only commit moves the rcu_scale_cleanup() and
rcu_scale_shutdown() functions to follow kfree_scale_cleanup().
This is code movement is in preparation for a bug-fix patch that invokes
kfree_scale_cleanup() from rcu_scale_cleanup().
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Stable-dep-of: 23fc8df26d ("rcu/rcuscale: Stop kfree_scale_thread thread(s) after unloading rcuscale")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef1ef3d476 ]
The rcu_scale_shutdown() and kfree_scale_shutdown() kthreads/functions
use wait_event() to wait for the rcuscale test to complete. However,
each updater thread in such a test waits for at least 100 grace periods.
If each grace period takes more than 1.2 seconds, which is long, but
not insanely so, this can trigger the hung-task timeout.
This commit therefore replaces those wait_event() calls with calls to
wait_event_idle(), which do not trigger the hung-task timeout.
Reported-by: kernel test robot <yujie.liu@intel.com>
Reported-by: Liam Howlett <liam.howlett@oracle.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Tested-by: Yujie Liu <yujie.liu@intel.com>
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Stable-dep-of: 23fc8df26d ("rcu/rcuscale: Stop kfree_scale_thread thread(s) after unloading rcuscale")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b409afe026 ]
The BUSTED-BOOST and TREE03 scenarios specify a mythical tree.use_softirq
module parameter, which means a failure to get full test coverage. This
commit therefore corrects the name to rcutree.use_softirq.
Fixes: e2b949d543 ("rcutorture: Make TREE03 use real-time tree.use_softirq setting")
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 401b0de3ae ]
The rcu_tasks_invoke_cbs() function relies on queue_work_on() to silently
fall back to WORK_CPU_UNBOUND when the specified CPU is offline. However,
the queue_work_on() function's silent fallback mechanism relies on that
CPU having been online at some time in the past. When queue_work_on()
is passed a CPU that has never been online, workqueue lockups ensue,
which can be bad for your kernel's general health and well-being.
This commit therefore checks whether a given CPU has ever been online,
and, if not substitutes WORK_CPU_UNBOUND in the subsequent call to
queue_work_on(). Why not simply omit the queue_work_on() call entirely?
Because this function is flooding callback-invocation notifications
to all CPUs, and must deal with possibilities that include a sparse
cpu_possible_mask.
This commit also moves the setting of the rcu_data structure's
->beenonline field to rcu_cpu_starting(), which executes on the
incoming CPU before that CPU has ever enabled interrupts. This ensures
that the required workqueues are present. In addition, because the
incoming CPU has not yet enabled its interrupts, there cannot yet have
been any softirq handlers running on this CPU, which means that the
WARN_ON_ONCE(!rdp->beenonline) within the RCU_SOFTIRQ handler cannot
have triggered yet.
Fixes: d363f833c6 ("rcu-tasks: Use workqueues for multiple rcu_tasks_invoke_cbs() invocations")
Reported-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15d44dfa40 ]
Currently, rcu_cpu_starting() is written so that it might be invoked
with interrupts enabled. However, it is always called when interrupts
are disabled, either by rcu_init(), notify_cpu_starting(), or from a
call point prior to the call to notify_cpu_starting().
But why bother requiring that interrupts be disabled? The purpose is
to allow the rcu_data structure's ->beenonline flag to be set after all
early processing has completed for the incoming CPU, thus allowing this
flag to be used to determine when workqueues have been set up for the
incoming CPU, while still allowing this flag to be used as a diagnostic
within rcu_core().
This commit therefore makes rcu_cpu_starting() rely on interrupts being
disabled.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Stable-dep-of: 401b0de3ae ("rcu-tasks: Stop rcu_tasks_invoke_cbs() from using never-onlined CPUs")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a16c190f7 ]
The devres variant of thermal_add_hwmon_sysfs() only takes the thermal
zone structure pointer as parameter.
Actually, it uses the tz->device to add it in the devres list.
It is preferable to use the device registering the thermal zone
instead of the thermal zone device itself. That prevents the driver
accessing the thermal zone structure internals and it is from my POV
more correct regarding how devm_ is used.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> #amlogic_thermal
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com> #sun8i_thermal
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> #MediaTek auxadc
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Stable-dep-of: 9301575df2 ("thermal/drivers/qoriq: Only enable supported sensors")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89382022b3 ]
Should an error occur after calling sun8i_ths_resource_init() in the probe
function, some resources need to be released, as already done in the
.remove() function.
Switch to the devm_clk_get_enabled() helper and add a new devm_action to
turn sun8i_ths_resource_init() into a fully managed function.
Move the place where reset_control_deassert() is called so that the
recommended order of reset release/clock enable steps is kept.
A64 manual states that:
3.3.6.4. Gating and reset
Make sure that the reset signal has been released before the release of
module clock gating;
This fixes the issue and removes some LoC at the same time.
Fixes: dccc5c3b6f ("thermal/drivers/sun8i: Add thermal driver for H6/H5/H3/A64/A83T/R40")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/a8ae84bd2dc4b55fe428f8e20f31438bf8bb6762.1684089931.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03f44ffb3d ]
If the intel_pstate driver is set to passive mode, then writing the
same value to the energy_performance_preference sysfs twice will fail.
This is caused by the wrong return value used (index of the matched
energy_perf_string), instead of the length of the passed in parameter.
Fix by forcing the internal return value to zero when the same
preference is passed in by user. This same issue is not present when
active mode is used for the driver.
Fixes: f6ebbcf08f ("cpufreq: intel_pstate: Implement passive mode with HWP enabled")
Reported-by: Niklas Neronin <niklas.neronin@intel.com>
Signed-off-by: Tero Kristo <tero.kristo@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b9c3ddcec ]
checker_stack_use_t32strd() and kprobe_handler() can be made static since
they are not used from other files, while coverage_start_registers()
and __kprobes_test_case() are used from assembler code, and just need
a declaration to avoid a warning with the global definition.
arch/arm/probes/kprobes/checkers-common.c:43:18: error: no previous prototype for 'checker_stack_use_t32strd'
arch/arm/probes/kprobes/core.c:236:16: error: no previous prototype for 'kprobe_handler'
arch/arm/probes/kprobes/test-core.c:723:10: error: no previous prototype for 'coverage_start_registers'
arch/arm/probes/kprobes/test-core.c:918:14: error: no previous prototype for '__kprobes_test_case_start'
arch/arm/probes/kprobes/test-core.c:952:14: error: no previous prototype for '__kprobes_test_case_end_16'
arch/arm/probes/kprobes/test-core.c:967:14: error: no previous prototype for '__kprobes_test_case_end_32'
Fixes: 6624cf651f ("ARM: kprobes: collects stack consumption for store instructions")
Fixes: 454f3e132d ("ARM/kprobes: Remove jprobe arm implementation")
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4384a70c88 ]
Commit f38d1a6d00 ("PM: domains: Allocate governor data dynamically
based on a genpd governor") started to use the in-parameters in
genpd_add_device(), without first doing a verification of them.
This isn't really a big problem, as most callers do a verification already.
Therefore, let's drop the verification from genpd_add_device() and make
sure all the callers take care of it instead.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Fixes: f38d1a6d00 ("PM: domains: Allocate governor data dynamically based on a genpd governor")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4658fe81b3 ]
After commit 3382388d71 ("intel_rapl: abstract RAPL common code"),
accessing to IOSF_MBI interface is done in the RAPL common code.
Thus it is the CONFIG_INTEL_RAPL_CORE that has dependency of
CONFIG_IOSF_MBI, while CONFIG_INTEL_RAPL_MSR does not.
This problem was not exposed previously because all the previous RAPL
common code users, aka, the RAPL MSR and MMIO I/F drivers, have
CONFIG_IOSF_MBI selected.
Fix the CONFIG_IOSF_MBI dependency in RAPL code. This also fixes a build
time failure when the RAPL TPMI I/F driver is introduced without
selecting CONFIG_IOSF_MBI.
x86_64-linux-ld: vmlinux.o: in function `set_floor_freq_atom':
intel_rapl_common.c:(.text+0x2dac9b8): undefined reference to `iosf_mbi_write'
x86_64-linux-ld: intel_rapl_common.c:(.text+0x2daca66): undefined reference to `iosf_mbi_read'
Reference to iosf_mbi.h is also removed from the RAPL MSR I/F driver.
Fixes: 3382388d71 ("intel_rapl: abstract RAPL common code")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/all/20230601213246.3271412-1-arnd@kernel.org
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d05b5e0baf ]
The current initialization of the struct x86_cpu_id via
pl4_support_ids[] is partial and wrong. It is initializing
"stepping" field with "X86_FEATURE_ANY" instead of "feature" field.
Use X86_MATCH_INTEL_FAM6_MODEL macro instead of initializing
each field of the struct x86_cpu_id for pl4_supported list of CPUs.
This X86_MATCH_INTEL_FAM6_MODEL macro internally uses another macro
X86_MATCH_VENDOR_FAM_MODEL_FEATURE for X86 based CPU matching with
appropriate initialized values.
Reported-by: Dave Hansen <dave.hansen@intel.com>
Link: https://lore.kernel.org/lkml/28ead36b-2d9e-1a36-6f4e-04684e420260@intel.com
Fixes: eb52bc2ae5 ("powercap: RAPL: Add Power Limit4 support for Meteor Lake SoC")
Fixes: b08b95cf30 ("powercap: RAPL: Add Power Limit4 support for Alder Lake-N and Raptor Lake-P")
Fixes: 5157559069 ("powercap: RAPL: Add Power Limit4 support for RaptorLake")
Fixes: 1cc5b9a411 ("powercap: Add Power Limit4 support for Alder Lake SoC")
Fixes: 8365a898fe ("powercap: Add Power Limit4 support")
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9368aa1882 ]
Since 315bada690 ("EDAC: Check for GHES preference in the
chipset-specific EDAC drivers"), vendor specific EDAC driver will not
probe correctly when CONFIG_ACPI_APEI_GHES is enabled but no GHES device
is present. Make ghes_get_devices() return NULL when the GHES device
list is empty to fix the problem.
Fixes: 9057a3f7ac ("EDAC/ghes: Prepare to make ghes_edac a proper module")
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a6a9f1c5a ]
The driver needs to migrate the perf context if the current using CPU going
to teardown. By the time calling the cpuhp::teardown() callback the
cpu_online_mask() hasn't updated yet and still includes the CPU going to
teardown. In current driver's implementation we may migrate the context
to the teardown CPU and leads to the below calltrace:
...
[ 368.104662][ T932] task:cpuhp/0 state:D stack: 0 pid: 15 ppid: 2 flags:0x00000008
[ 368.113699][ T932] Call trace:
[ 368.116834][ T932] __switch_to+0x7c/0xbc
[ 368.120924][ T932] __schedule+0x338/0x6f0
[ 368.125098][ T932] schedule+0x50/0xe0
[ 368.128926][ T932] schedule_preempt_disabled+0x18/0x24
[ 368.134229][ T932] __mutex_lock.constprop.0+0x1d4/0x5dc
[ 368.139617][ T932] __mutex_lock_slowpath+0x1c/0x30
[ 368.144573][ T932] mutex_lock+0x50/0x60
[ 368.148579][ T932] perf_pmu_migrate_context+0x84/0x2b0
[ 368.153884][ T932] hisi_pcie_pmu_offline_cpu+0x90/0xe0 [hisi_pcie_pmu]
[ 368.160579][ T932] cpuhp_invoke_callback+0x2a0/0x650
[ 368.165707][ T932] cpuhp_thread_fun+0xe4/0x190
[ 368.170316][ T932] smpboot_thread_fn+0x15c/0x1a0
[ 368.175099][ T932] kthread+0x108/0x13c
[ 368.179012][ T932] ret_from_fork+0x10/0x18
...
Use function cpumask_any_but() to find one correct active cpu to fixes
this issue.
Fixes: 8404b0fbc7 ("drivers/perf: hisi: Add driver for HiSilicon PCIe PMU")
Signed-off-by: Junhao He <hejunhao3@huawei.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Yicong Yang <yangyicong@hisilicon.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20230608114326.27649-1-hejunhao3@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 195edce08b ]
tl;dr: There is a race in the TDX private<=>shared conversion code
which could kill the TDX guest. Fix it by changing conversion
ordering to eliminate the window.
TDX hardware maintains metadata to track which pages are private and
shared. Additionally, TDX guests use the guest x86 page tables to
specify whether a given mapping is intended to be private or shared.
Bad things happen when the intent and metadata do not match.
So there are two thing in play:
1. "the page" -- the physical TDX page metadata
2. "the mapping" -- the guest-controlled x86 page table intent
For instance, an unrecoverable exit to VMM occurs if a guest touches a
private mapping that points to a shared physical page.
In summary:
* Private mapping => Private Page == OK (obviously)
* Shared mapping => Shared Page == OK (obviously)
* Private mapping => Shared Page == BIG BOOM!
* Shared mapping => Private Page == OK-ish
(It will read generate a recoverable #VE via handle_mmio())
Enter load_unaligned_zeropad(). It can touch memory that is adjacent but
otherwise unrelated to the memory it needs to touch. It will cause one
of those unrecoverable exits (aka. BIG BOOM) if it blunders into a
shared mapping pointing to a private page.
This is a problem when __set_memory_enc_pgtable() converts pages from
shared to private. It first changes the mapping and second modifies
the TDX page metadata. It's moving from:
* Shared mapping => Shared Page == OK
to:
* Private mapping => Shared Page == BIG BOOM!
This means that there is a window with a shared mapping pointing to a
private page where load_unaligned_zeropad() can strike.
Add a TDX handler for guest.enc_status_change_prepare(). This converts
the page from shared to private *before* the page becomes private. This
ensures that there is never a private mapping to a shared page.
Leave a guest.enc_status_change_finish() in place but only use it for
private=>shared conversions. This will delay updating the TDX metadata
marking the page private until *after* the mapping matches the metadata.
This also ensures that there is never a private mapping to a shared page.
[ dhansen: rewrite changelog ]
Fixes: 7dbde76316 ("x86/mm/cpa: Add support for TDX shared memory")
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Link: https://lore.kernel.org/all/20230606095622.1939-3-kirill.shutemov%40linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71746c995c ]
It turns out that my naive DTC reset logic fails to work as intended,
since, after checking with the hardware designers, the PMU actually
needs to be fully enabled in order to correctly clear any pending
overflows. Therefore, invert the sequence to start with turning on both
enables so that we can reliably get the DTCs into a known state, then
moving to our normal counters-stopped state from there. Since all the
DTM counters have already been unpaired during the initial discovery
pass, we just need to additionally reset the cycle counters to ensure
that no other unexpected overflows occur during this period.
Fixes: 0ba64770a2 ("perf: Add Arm CMN-600 PMU driver")
Reported-by: Geoff Blake <blakgeof@amazon.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/0ea4559261ea394f827c9aee5168c77a60aaee03.1684946389.git.robin.murphy@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5d1c87220 ]
Currently, while calculating residency and latency values, right
operands may overflow if resulting values are big enough.
To prevent this, albeit unlikely case, play it safe and convert
right operands to left ones' type s64.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: 30f604283e ("PM / Domains: Allow domain power states to be read from DT")
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b5bf64c89 ]
Smatch reports:
drivers/clocksource/timer-cadence-ttc.c:529 ttc_timer_probe()
warn: 'timer_baseaddr' from of_iomap() not released on lines: 498,508,516.
timer_baseaddr may have the problem of not being released after use,
I replaced it with the devm_of_iomap() function and added the clk_put()
function to cleanup the "clk_ce" and "clk_cs".
Fixes: e932900a32 ("arm: zynq: Use standard timer binding")
Fixes: 70504f311d ("clocksource/drivers/cadence_ttc: Convert init function to return error")
Signed-off-by: Feng Mingxi <m202271825@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230425065611.702917-1-m202271825@hust.edu.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c731cd0b6d ]
If a bio gets split, it needs to have a proper file_offset for checksum
validation and repair to work properly.
Based on feedback from Josef, commit 852eee62d3 ("btrfs: allow
btrfs_submit_bio to split bios") skipped this adjustment for ONE_ORDERED
bios. But if we actually ever need to split a ONE_ORDERED read bio, this
will lead to a wrong file offset in the repair code. Right now the only
user of the file_offset is logging of an error message so this is mostly
harmless, but the wrong offset might be more problematic for additional
users in the future.
Fixes: 852eee62d3 ("btrfs: allow btrfs_submit_bio to split bios")
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2cef0c79bb ]
btrfs_split_bio expects a btrfs_bio as argument and always allocates one.
Type both the orig_bio argument and the return value as struct btrfs_bio
to improve type safety.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David Sterba <dsterba@suse.com>
Stable-dep-of: c731cd0b6d ("btrfs: fix file_offset for REQ_BTRFS_ONE_ORDERED bios that get split")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d9e522010 ]
itimer_delete() has a retry loop when the timer is concurrently expired. On
non-RT kernels this just spin-waits until the timer callback has completed,
except for posix CPU timers which have HAVE_POSIX_CPU_TIMERS_TASK_WORK
enabled.
In that case and on RT kernels the existing task could live lock when
preempting the task which does the timer delivery.
Replace spin_unlock() with an invocation of timer_wait_running() to handle
it the same way as the other retry loops in the posix timer code.
Fixes: ec8f954a40 ("posix-timers: Use a callback for cancel synchronization on PREEMPT_RT")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/87v8g7c50d.ffs@tglx
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 001b8ccd06 ]
In compact 4B, two adjacent lclusters are packed together as a unit to
form on-disk indexes for effective random access, as below:
(amortized = 4, vcnt = 2)
_____________________________________________
|___@_____ encoded bits __________|_ blkaddr _|
0 . amortized * vcnt = 8
. .
. . amortized * vcnt - 4 = 4
. .
.____________________________.
|_type (2 bits)_|_clusterofs_|
Therefore, encoded bits for each pack are 32 bits (4 bytes). IOWs,
since each lcluster can get 16 bits for its type and clusterofs, the
maximum supported lclustersize for compact 4B format is 16k (14 bits).
Fix this to enable compact 4B format for 16k lclusters (blocks), which
is tested on an arm64 server with 16k page size.
Fixes: 152a333a58 ("staging: erofs: add compacted compression indexes support")
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Link: https://lore.kernel.org/r/20230601112341.56960-1-hsiangkao@linux.alibaba.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit baf6d18b11 ]
I noticed that svc_rqst_release_pages() was still unnecessarily
releasing a page when svc_rdma_recvfrom() returns zero.
Fixes: a53d5cb064 ("svcrdma: Avoid releasing a page in svc_xprt_release()")
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48f31e4964 ]
While compiling with W=1, both gcc and clang complain about a
tricky way to initialize an array by filling it with a non-zero
value and then overrride some of the array elements.
In this case the override is intentional, so just disable the
specific warning for only this part of the code.
Note: the flag "-Woverride-init" is recognized by both compilers,
but the warning msg from clang reports "-Winitializer-overrides".
The doc of clang clarifies that the two flags are synonyms, so use
here only the flag name common on both compilers.
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Fixes: c297493336 ("irqchip/stm32-exti: Simplify irq description table")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230601155614.34490-1-antonio.borneo@foss.st.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb07b8f834 ]
The hierarchy of PCH PIC, PCH PCI MSI and EIONTC is as following:
PCH PIC ------->|
|---->EIOINTC
PCH PCI MSI --->|
so the irq_data list of irq_desc for IRQs on PCH PIC and PCH PCI MSI
is like this:
irq_desc->irq_data(domain: PCH PIC)->parent_data(domain: EIOINTC)
irq_desc->irq_data(domain: PCH PCI MSI)->parent_data(domain: EIOINTC)
In eiointc_resume(), the irq_data passed into eiointc_set_irq_affinity()
should be matched to EIOINTC domain instead of PCH PIC or PCH PCI MSI
domain, so fix it.
Fixes: a90335c2df ("irqchip/loongson-eiointc: Add suspend/resume support")
Reported-by: yangqiming <yangqiming@loongson.cn>
Signed-off-by: Jianmin Lv <lvjianmin@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230614115936.5950-6-lvjianmin@loongson.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd7de3704a ]
Commit 99d055b4fd ("block: remove per-disk debugfs files in
blk_unregister_queue") moves blk_trace_shutdown() from
blk_release_queue() to blk_unregister_queue(), this is safe if blktrace
is created through sysfs, however, there is a regression in corner
case.
blktrace can still be enabled after del_gendisk() through ioctl if
the disk is opened before del_gendisk(), and if blktrace is not shutdown
through ioctl before closing the disk, debugfs entries will be leaked.
Fix this problem by shutdown blktrace in disk_release(), this is safe
because blk_trace_remove() is reentrant.
Fixes: 99d055b4fd ("block: remove per-disk debugfs files in blk_unregister_queue")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230610022003.2557284-4-yukuai1@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7db922bae3 ]
Commit 6cce3b23f6 ("[PATCH] md: write intent bitmap support for raid10")
add bitmap support, and it changed that write io is submitted through
daemon thread because bitmap need to be updated before write io. And
later, plug is used to fix performance regression because all the write io
will go to demon thread, which means io can't be issued concurrently.
However, if bitmap is not enabled, the write io should not go to daemon
thread in the first place, and plug is not needed as well.
Fixes: 6cce3b23f6 ("[PATCH] md: write intent bitmap support for raid10")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230529131106.2123367-5-yukuai1@huaweicloud.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ae6aaf769 ]
When removing a disk with replacement, the replacement will be used to
replace rdev. During this process, there is a brief window in which both
rdev and replacement are read as NULL in raid10_write_request(). This
will result in io not being submitted but it should be.
//remove //write
raid10_remove_disk raid10_write_request
mirror->rdev = NULL
read rdev -> NULL
mirror->rdev = mirror->replacement
mirror->replacement = NULL
read replacement -> NULL
Fix it by reading replacement first and rdev later, meanwhile, use smp_mb()
to prevent memory reordering.
Fixes: 475b0321a4 ("md/raid10: writes should get directed to replacement as well as original.")
Signed-off-by: Li Nan <linan122@huawei.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230602091839.743798-3-linan666@huaweicloud.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 34817a2441 ]
There are two check of 'mreplace' in raid10_sync_request(). In the first
check, 'need_replace' will be set and 'mreplace' will be used later if
no-Faulty 'mreplace' exists, In the second check, 'mreplace' will be
set to NULL if it is Faulty, but 'need_replace' will not be changed
accordingly. null-ptr-deref occurs if Faulty is set between two check.
Fix it by merging two checks into one. And replace 'need_replace' with
'mreplace' because their values are always the same.
Fixes: ee37d7314a ("md/raid10: Fix raid10 replace hang when new added disk faulty")
Signed-off-by: Li Nan <linan122@huawei.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230527072218.2365857-2-linan666@huaweicloud.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 301867b1c1 ]
If we write a large number to md/bitmap_set_bits, md_bitmap_checkpage()
will return -EINVAL because 'page >= bitmap->pages', but the return value
was not checked immediately in md_bitmap_get_counter() in order to set
*blocks value and slab-out-of-bounds occurs.
Move check of 'page >= bitmap->pages' to md_bitmap_get_counter() and
return directly if true.
Fixes: ef42567335 ("md/bitmap: optimise scanning of empty bitmaps.")
Signed-off-by: Li Nan <linan122@huawei.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230515134808.3936750-2-linan666@huaweicloud.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 665e89ab7c ]
The below-mentioned patch was intended to simplify refcounting on the
svc_serv used by locked. The goal was to only ever have a single
reference from the single thread. To that end we dropped a call to
lockd_start_svc() (except when creating thread) which would take a
reference, and dropped the svc_put(serv) that would drop that reference.
Unfortunately we didn't also remove the svc_get() from
lockd_create_svc() in the case where the svc_serv already existed.
So after the patch:
- on the first call the svc_serv was allocated and the one reference
was given to the thread, so there are no extra references
- on subsequent calls svc_get() was called so there is now an extra
reference.
This is clearly not consistent.
The inconsistency is also clear in the current code in lockd_get()
takes *two* references, one on nlmsvc_serv and one by incrementing
nlmsvc_users. This clearly does not match lockd_put().
So: drop that svc_get() from lockd_get() (which used to be in
lockd_create_svc().
Reported-by: Ido Schimmel <idosch@idosch.org>
Closes: https://lore.kernel.org/linux-nfs/ZHsI%2FH16VX9kJQX1@shredder/T/#u
Fixes: b73a297204 ("lockd: move lockd_start_svc() call into lockd_create_svc()")
Signed-off-by: NeilBrown <neilb@suse.de>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f1731df60 ]
In __blk_mq_tag_busy/idle(), updating 'active_queues' and calculating
'wake_batch' is not atomic:
t1: t2:
_blk_mq_tag_busy blk_mq_tag_busy
inc active_queues
// assume 1->2
inc active_queues
// 2 -> 3
blk_mq_update_wake_batch
// calculate based on 3
blk_mq_update_wake_batch
/* calculate based on 2, while active_queues is actually 3. */
Fix this problem by protecting them wih 'tags->lock', this is not a hot
path, so performance should not be concerned. And now that all writers
are inside the lock, switch 'actives_queues' from atomic to unsigned
int.
Fixes: 180dccb0db ("blk-mq: fix tag_get wait task can't be awakened")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20230610023043.2559121-1-yukuai1@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84b9b44b99 ]
This driver fails to link when CRYPTO is disabled, or in a loadable
module:
WARNING: unmet direct dependencies detected for CRYPTO_GCM
WARNING: unmet direct dependencies detected for CRYPTO_AEAD2
Depends on [m]: CRYPTO [=m]
Selected by [y]:
- SEV_GUEST [=y] && VIRT_DRIVERS [=y] && AMD_MEM_ENCRYPT [=y]
x86_64-linux-ld: crypto/aead.o: in function `crypto_register_aeads':
Fixes: fce96cf044 ("virt: Add SEV-SNP guest driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20230117171416.2715125-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d2af77e31 ]
When blkg_alloc() is called to allocate a blkcg_gq structure
with the associated blkg_iostat_set's, there are 2 fields within
blkg_iostat_set that requires proper initialization - blkg & sync.
The former field was introduced by commit 3b8cc62987 ("blk-cgroup:
Optimize blkcg_rstat_flush()") while the later one was introduced by
commit f733164829 ("blk-cgroup: reimplement basic IO stats using
cgroup rstat").
Unfortunately those fields in the blkg_iostat_set's are not properly
re-initialized when they are cleared in v1's blkcg_reset_stats(). This
can lead to a kernel panic due to NULL pointer access of the blkg
pointer. The missing initialization of sync is less problematic and
can be a problem in a debug kernel due to missing lockdep initialization.
Fix these problems by re-initializing them after memory clearing.
Fixes: 3b8cc62987 ("blk-cgroup: Optimize blkcg_rstat_flush()")
Fixes: f733164829 ("blk-cgroup: reimplement basic IO stats using cgroup rstat")
Signed-off-by: Waiman Long <longman@redhat.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20230606180724.2455066-1-longman@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5dee19b6b2 ]
When calculating an end address based on an unsigned int number of pages,
any value greater than or equal to 0x100000 that is shift PAGE_SHIFT bits
results in a 0 value, resulting in an invalid end address. Change the
number of pages variable in various routines from an unsigned int to an
unsigned long to calculate the end address correctly.
Fixes: 5e5ccff60a ("x86/sev: Add helper for validating pages in early enc attribute changes")
Fixes: dc3f3d2474 ("x86/mm: Validate memory when changing the C-bit")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/6a6e4eea0e1414402bac747744984fa4e9c01bb6.1686063086.git.thomas.lendacky@amd.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 967c28b23f ]
After heavily stressing EROFS with several images which include a
hand-crafted image of repeated patterns for more than 46 days, I found
two chains could be linked with each other almost simultaneously and
form a loop so that the entire loop won't be submitted. As a
consequence, the corresponding file pages will remain locked forever.
It can be _only_ observed on data-deduplicated compressed images.
For example, consider two chains with five pclusters in total:
Chain 1: 2->3->4->5 -- The tail pcluster is 5;
Chain 2: 5->1->2 -- The tail pcluster is 2.
Chain 2 could link to Chain 1 with pcluster 5; and Chain 1 could link
to Chain 2 at the same time with pcluster 2.
Since hooked chains are all linked locklessly now, I have no idea how
to simply avoid the race. Instead, let's avoid hooked chains completely
until I could work out a proper way to fix this and end users finally
tell us that it's needed to add it back.
Actually, this optimization can be found with multi-threaded workloads
(especially even more often on deduplicated compressed images), yet I'm
not sure about the overall system impacts of not having this compared
with implementation complexity.
Fixes: 267f2492c8 ("erofs: introduce multi-reference pclusters (fully-referenced)")
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Reviewed-by: Yue Hu <huyue2@coolpad.com>
Link: https://lore.kernel.org/r/20230526201459.128169-4-hsiangkao@linux.alibaba.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 247c8d2f98 ]
A couple of functions from fs/pipe.c are used both internally
and for the watch queue code, but the declaration is only
visible when the latter is enabled:
fs/pipe.c:1254:5: error: no previous prototype for 'pipe_resize_ring'
fs/pipe.c:758:15: error: no previous prototype for 'account_pipe_buffers'
fs/pipe.c:764:6: error: no previous prototype for 'too_many_pipe_buffers_soft'
fs/pipe.c:771:6: error: no previous prototype for 'too_many_pipe_buffers_hard'
fs/pipe.c:777:6: error: no previous prototype for 'pipe_is_unprivileged_user'
Make the visible unconditionally to avoid these warnings.
Fixes: c73be61ced ("pipe: Add general notification queue support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Message-Id: <20230516195629.551602-1-arnd@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2820433be2 upstream.
[Why & How]
In the commit 32953485c5 ("drm/amd/display: Do not update DRR while
BW optimizations pending"), a modification was added to avoid adjusting
DRR if optimized bandwidth is set. This change was only intended for
DCN, but one part of the patch changed the code path for DCE devices and
caused regressions to the kms_vrr test. To address this problem, this
commit adds a modification in which dc_stream_adjust_vmin_vmax will be
fully executed in DCE devices.
Fixes: 32953485c5 ("drm/amd/display: Do not update DRR while BW optimizations pending")
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 249bed821b upstream.
The version is fetched once in check_version(), which then does some
validation and then overwrites the version in userspace with the API
version supported by the kernel. copy_params() then fetches the version
from userspace *again*, and this time no validation is done. The result
is that the kernel's version number is completely controllable by
userspace, provided that userspace can win a race condition.
Fix this flaw by not copying the version back to the kernel the second
time. This is not exploitable as the version is not further used in the
kernel. However, it could become a problem if future patches start
relying on the version field.
Cc: stable@vger.kernel.org
Signed-off-by: Demi Marie Obenour <demi@invisiblethingslab.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e1b37563ca upstream.
gtags considers any file outside of its current working directory
"outside the source tree" and refuses to index it. For O= kernel builds,
or when "make" is invoked from a directory other then the kernel source
tree, gtags ignores the entire kernel source and generates an empty
index.
Force-set gtags current working directory to the kernel source tree.
Due to commit 9da0763bdd ("kbuild: Use relative path when building in
a subdir of the source tree"), if the kernel build is done in a
sub-directory of the kernel source tree, the kernel Makefile will set
the kernel's $srctree to ".." for shorter compile-time and run-time
warnings. Consequently, the list of files to be indexed will be in the
"../*" form, rendering all such paths invalid once gtags switches to the
kernel source tree as its current working directory.
If gtags indexing is requested and the build directory is not the kernel
source tree, index all files in absolute-path form.
Note, indexing in absolute-path form will not affect the generated
index, as paths in gtags indices are always relative to the gtags "root
directory" anyway (as evidenced by "gtags --dump").
Signed-off-by: Ahmed S. Darwish <darwi@linutronix.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f0220af58 upstream.
commit eb0764b822 ("cxl/port: Enable the HDM decoder capability for switch ports")
...was added on the observation of CXL memory not being accessible after
setting up a region on a "cold-plugged" device. A "cold-plugged" CXL
device is one that was not present at boot, so platform-firmware/BIOS
has no chance to set it up.
While it is true that the debug found the enable bit clear in the
host-bridge's instance of the global control register (CXL 3.0
8.2.4.19.2 CXL HDM Decoder Global Control Register), that bit is
described as:
"This bit is only applicable to CXL.mem devices and shall
return 0 on CXL Host Bridges and Upstream Switch Ports."
So it is meant to be zero, and further testing confirmed that this "fix"
had no effect on the failure. Revert it, and be more vigilant about
proposed fixes in the future. Since the original copied stable@, flag
this revert for stable@ as well.
Cc: <stable@vger.kernel.org>
Fixes: eb0764b822 ("cxl/port: Enable the HDM decoder capability for switch ports")
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/168685882012.3475336.16733084892658264991.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f66066bc51 upstream.
While our user stacks can grow either down (all common architectures) or
up (parisc and the ia64 register stack), the initial stack setup when we
copy the argument and environment strings to the new stack at execve()
time is always done by extending the stack downwards.
But it turns out that in commit 8d7071af89 ("mm: always expand the
stack with the mmap write lock held"), as part of making the stack
growing code more robust, 'expand_downwards()' was now made to actually
check the vma flags:
if (!(vma->vm_flags & VM_GROWSDOWN))
return -EFAULT;
and that meant that this execve-time stack expansion started failing on
parisc, because on that architecture, the stack flags do not contain the
VM_GROWSDOWN bit.
At the same time the new check in expand_downwards() is clearly correct,
and simplified the callers, so let's not remove it.
The solution is instead to just codify the fact that yes, during
execve(), the stack grows down. This not only matches reality, it ends
up being particularly simple: we already have special execve-time flags
for the stack (VM_STACK_INCOMPLETE_SETUP) and use those flags to avoid
page migration during this setup time (see vma_is_temporary_stack() and
invalid_migration_vma()).
So just add VM_GROWSDOWN to that set of temporary flags, and now our
stack flags automatically match reality, and the parisc stack expansion
works again.
Note that the VM_STACK_INCOMPLETE_SETUP bits will be cleared when the
stack is finalized, so we only add the extra VM_GROWSDOWN bit on
CONFIG_STACK_GROWSUP architectures (ie parisc) rather than adding it in
general.
Link: https://lore.kernel.org/all/612eaa53-6904-6e16-67fc-394f4faa0e16@bell.net/
Link: https://lore.kernel.org/all/5fd98a09-4792-1433-752d-029ae3545168@gmx.de/
Fixes: 8d7071af89 ("mm: always expand the stack with the mmap write lock held")
Reported-by: John David Anglin <dave.anglin@bell.net>
Reported-and-tested-by: Helge Deller <deller@gmx.de>
Reported-and-tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 112a7f9c8e upstream.
ACPI r6.5, sec 6.5.4, describes how AML is unable to access an
OperationRegion unless _REG has been called to connect a handler:
The OS runs _REG control methods to inform AML code of a change in the
availability of an operation region. When an operation region handler is
unavailable, AML cannot access data fields in that region. (Operation
region writes will be ignored and reads will return indeterminate data.)
The PCI core does not call _REG at any time, leading to the undefined
behavior mentioned in the spec.
The spec explains that _REG should be executed to indicate whether a
given region can be accessed:
Once _REG has been executed for a particular operation region, indicating
that the operation region handler is ready, a control method can access
fields in the operation region. Conversely, control methods must not
access fields in operation regions when _REG method execution has not
indicated that the operation region handler is ready.
An example included in the spec demonstrates calling _REG when devices are
turned off: "when the host controller or bridge controller is turned off
or disabled, PCI Config Space Operation Regions for child devices are
no longer available. As such, ETH0’s _REG method will be run when it
is turned off and will again be run when PCI1 is turned off."
It is reported that ASMedia PCIe GPIO controllers fail functional tests
after the system has returning from suspend (S3 or s2idle). This is because
the BIOS checks whether the OSPM has called the _REG method to determine
whether it can interact with the OperationRegion assigned to the device as
part of the other AML called for the device.
To fix this issue, call acpi_evaluate_reg() when devices are transitioning
to D3cold or D0.
[bhelgaas: split pci_power_t checking to preliminary patch]
Link: https://uefi.org/specs/ACPI/6.5/06_Device_Configuration.html#reg-region
Link: https://lore.kernel.org/r/20230620140451.21007-1-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5557b62634 upstream.
Previously acpi_pci_set_power_state() assumed the requested power state was
valid (PCI_D0 ... PCI_D3cold). If a caller supplied something else, we
could index outside the state_conv[] array and pass junk to
acpi_device_set_power().
Validate the pci_power_t parameter and return -EINVAL if it's invalid.
Link: https://lore.kernel.org/r/20230621222857.GA122930@bhelgaas
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 03f889378f upstream.
MMU version of lock_mm_and_find_vma releases the mm lock before
returning when VMA is not found. Do the same in noMMU version.
This fixes hang on an attempt to handle protection fault.
Fixes: d85a143b69 ("xtensa: fix NOMMU build with lock_mm_and_find_vma() conversion")
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d85a143b69 upstream.
It turns out that xtensa has a really odd configuration situation: you
can do a no-MMU config, but still have the page fault code enabled.
Which doesn't sound all that sensible, but it turns out that xtensa can
have protection faults even without the MMU, and we have this:
config PFAULT
bool "Handle protection faults" if EXPERT && !MMU
default y
help
Handle protection faults. MMU configurations must enable it.
noMMU configurations may disable it if used memory map never
generates protection faults or faults are always fatal.
If unsure, say Y.
which completely violated my expectations of the page fault handling.
End result: Guenter reports that the xtensa no-MMU builds all fail with
arch/xtensa/mm/fault.c: In function ‘do_page_fault’:
arch/xtensa/mm/fault.c:133:8: error: implicit declaration of function ‘lock_mm_and_find_vma’
because I never exposed the new lock_mm_and_find_vma() function for the
no-MMU case.
Doing so is simple enough, and fixes the problem.
Reported-and-tested-by: Guenter Roeck <linux@roeck-us.net>
Fixes: a050ba1e74 ("mm/fault: convert remaining simple cases to lock_mm_and_find_vma()")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e55e5df193 upstream.
As already mentioned in my merge message for the 'expand-stack' branch,
we have something like 24 different versions of the page fault path for
all our different architectures, all just _slightly_ different due to
various historical reasons (usually related to exactly when they
branched off the original i386 version, and the details of the other
architectures they had in their history).
And a few of them had some silly mistake in the conversion.
Most of the architectures call the faulting address 'address' in the
fault path. But not all. Some just call it 'addr'. And if you end up
doing a bit too much copy-and-paste, you end up with the wrong version
in the places that do it differently.
In this case it was csky.
Fixes: a050ba1e74 ("mm/fault: convert remaining simple cases to lock_mm_and_find_vma()")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea3f827287 upstream.
In commit 8d7071af89 ("mm: always expand the stack with the mmap write
lock held") I tried to deal with the remaining odd page fault handling
cases. The oddest one is ia64, which has stacks that grow both up and
down. And because ia64 was _so_ odd, I asked people to verify the end
result.
But a close second oddity is parisc, which is the only one that has a
main stack growing up (our "CONFIG_STACK_GROWSUP" config option). But
it looked obvious enough that I didn't worry about it.
I should have worried a bit more. Not because it was particularly
complex, but because I just used the wrong variable name.
The previous vma isn't called "prev", it's called "prev_vma". Blush.
Fixes: 8d7071af89 ("mm: always expand the stack with the mmap write lock held")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b26eadbf2 upstream.
The sparc32 conversion to lock_mm_and_find_vma() in commit a050ba1e74
("mm/fault: convert remaining simple cases to lock_mm_and_find_vma()")
missed the fact that we didn't actually have a 'regs' pointer available
in the 'force_user_fault()' case.
It's there in the regular page fault path ("do_sparc_fault()"), but not
the window underflow/overflow paths.
Which is all fine - we can just pass in a NULL pointer. The register
state is only used to avoid deadlock with kernel faults, which is not
the case for any of these register window faults.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: a050ba1e74 ("mm/fault: convert remaining simple cases to lock_mm_and_find_vma()")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a425ac5365 upstream.
It feels very unlikely that anybody would want to do a GUP in an
unmapped area under the stack pointer, but real users sometimes do some
really strange things. So add a (temporary) warning for the case where
a GUP fails and expanding the stack might have made it work.
It's trivial to do the expansion in the caller as part of getting the mm
lock in the first place - see __access_remote_vm() for ptrace, for
example - it's just that it's unnecessarily painful to do it deep in the
guts of the GUP lookup when we might have to drop and re-take the lock.
I doubt anybody actually does anything quite this strange, but let's be
proactive: adding these warnings is simple, and will make debugging it
much easier if they trigger.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d7071af89 upstream.
This finishes the job of always holding the mmap write lock when
extending the user stack vma, and removes the 'write_locked' argument
from the vm helper functions again.
For some cases, we just avoid expanding the stack at all: drivers and
page pinning really shouldn't be extending any stacks. Let's see if any
strange users really wanted that.
It's worth noting that architectures that weren't converted to the new
lock_mm_and_find_vma() helper function are left using the legacy
"expand_stack()" function, but it has been changed to drop the mmap_lock
and take it for writing while expanding the vma. This makes it fairly
straightforward to convert the remaining architectures.
As a result of dropping and re-taking the lock, the calling conventions
for this function have also changed, since the old vma may no longer be
valid. So it will now return the new vma if successful, and NULL - and
the lock dropped - if the area could not be extended.
Tested-by: Vegard Nossum <vegard.nossum@oracle.com>
Tested-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> # ia64
Tested-by: Frank Scheiner <frank.scheiner@web.de> # ia64
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f313c51d26 upstream.
This is a small step towards a model where GUP itself would not expand
the stack, and any user that needs GUP to not look up existing mappings,
but actually expand on them, would have to do so manually before-hand,
and with the mm lock held for writing.
It turns out that execve() already did almost exactly that, except it
didn't take the mm lock at all (it's single-threaded so no locking
technically needed, but it could cause lockdep errors). And it only did
it for the CONFIG_STACK_GROWSUP case, since in that case GUP has
obviously never expanded the stack downwards.
So just make that CONFIG_STACK_GROWSUP case do the right thing with
locking, and enable it generally. This will eventually help GUP, and in
the meantime avoids a special case and the lockdep issue.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f440fa1ac9 upstream.
Make calls to extend_vma() and find_extend_vma() fail if the write lock
is required.
To avoid making this a flag-day event, this still allows the old
read-locking case for the trivial situations, and passes in a flag to
say "is it write-locked". That way write-lockers can say "yes, I'm
being careful", and legacy users will continue to work in all the common
cases until they have been fully converted to the new world order.
Co-Developed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2cd76c50d0 upstream.
This is one of the simple cases, except there's no pt_regs pointer.
Which is fine, as lock_mm_and_find_vma() is set up to work fine with a
NULL pt_regs.
Powerpc already enabled LOCK_MM_AND_FIND_VMA for the main CPU faulting,
so we can just use the helper without any extra work.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a050ba1e74 upstream.
This does the simple pattern conversion of alpha, arc, csky, hexagon,
loongarch, nios2, sh, sparc32, and xtensa to the lock_mm_and_find_vma()
helper. They all have the regular fault handling pattern without odd
special cases.
The remaining architectures all have something that keeps us from a
straightforward conversion: ia64 and parisc have stacks that can grow
both up as well as down (and ia64 has special address region checks).
And m68k, microblaze, openrisc, sparc64, and um end up having extra
rules about only expanding the stack down a limited amount below the
user space stack pointer. That is something that x86 used to do too
(long long ago), and it probably could just be skipped, but it still
makes the conversion less than trivial.
Note that this conversion was done manually and with the exception of
alpha without any build testing, because I have a fairly limited cross-
building environment. The cases are all simple, and I went through the
changes several times, but...
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b35ca3e45 upstream.
arm has an additional check for address < FIRST_USER_ADDRESS before
expanding the stack. Since FIRST_USER_ADDRESS is defined everywhere
(generally as 0), move that check to the generic expand_downwards().
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae870a68b5 upstream.
This converts arm64 to use the new page fault helper. It was very
straightforward, but still needed a fix for the "obvious" conversion I
initially did. Thanks to Suren for the fix and testing.
Fixed-and-tested-by: Suren Baghdasaryan <surenb@google.com>
Unnecessary-code-removal-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eda0047296 upstream.
This is done as a separate patch from introducing the new
lock_mm_and_find_vma() helper, because while it's an obvious change,
it's not what x86 used to do in this area.
We already abort the page fault on fatal signals anyway, so why should
we wait for the mmap lock only to then abort later? With the new helper
function that returns without the lock held on failure anyway, this is
particularly easy and straightforward.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2508ec5a5 upstream.
.. and make x86 use it.
This basically extracts the existing x86 "find and expand faulting vma"
code, but extends it to also take the mmap lock for writing in case we
actually do need to expand the vma.
We've historically short-circuited that case, and have some rather ugly
special logic to serialize the stack segment expansion (since we only
hold the mmap lock for reading) that doesn't match the normal VM
locking.
That slight violation of locking worked well, right up until it didn't:
the maple tree code really does want proper locking even for simple
extension of an existing vma.
So extract the code for "look up the vma of the fault" from x86, fix it
up to do the necessary write locking, and make it available as a helper
function for other architectures that can use the common helper.
Note: I say "common helper", but it really only handles the normal
stack-grows-down case. Which is all architectures except for PA-RISC
and IA64. So some rare architectures can't use the helper, but if they
care they'll just need to open-code this logic.
It's also worth pointing out that this code really would like to have an
optimistic "mmap_upgrade_trylock()" to make it quicker to go from a
read-lock (for the common case) to taking the write lock (for having to
extend the vma) in the normal single-threaded situation where there is
no other locking activity.
But that _is_ all the very uncommon special case, so while it would be
nice to have such an operation, it probably doesn't matter in reality.
I did put in the skeleton code for such a possible future expansion,
even if it only acts as pseudo-documentation for what we're doing.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd00dd2585 upstream.
Check the write offset end bounds before using it as the offset into the
pivot array. This avoids a possible out-of-bounds access on the pivot
array if the write extends to the last slot in the node, in which case the
node maximum should be used as the end pivot.
akpm: this doesn't affect any current callers, but new users of mapletree
may encounter this problem if backported into earlier kernels, so let's
fix it in -stable kernels in case of this.
Link: https://lkml.kernel.org/r/20230506024752.2550-1-zhangpeng.00@bytedance.com
Fixes: 54a611b605 ("Maple Tree: add new data structure")
Signed-off-by: Peng Zhang <zhangpeng.00@bytedance.com>
Reviewed-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e38910c007 upstream.
With commit d674a8f123 ("can: isotp: isotp_sendmsg(): fix return
error on FC timeout on TX path") the missing correct return value in
the case of a protocol error was introduced.
But the way the error value has been read and sent to the user space
does not follow the common scheme to clear the error after reading
which is provided by the sock_error() function. This leads to an error
report at the following write() attempt although everything should be
working.
Fixes: d674a8f123 ("can: isotp: isotp_sendmsg(): fix return error on FC timeout on TX path")
Reported-by: Carsten Schmidt <carsten.schmidt-achim@t-online.de>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20230607072708.38809-1-socketcan@hartkopp.net
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d7893093a7 upstream.
TLDR: It's a mess.
When kexec() is executed on a system with offline CPUs, which are parked in
mwait_play_dead() it can end up in a triple fault during the bootup of the
kexec kernel or cause hard to diagnose data corruption.
The reason is that kexec() eventually overwrites the previous kernel's text,
page tables, data and stack. If it writes to the cache line which is
monitored by a previously offlined CPU, MWAIT resumes execution and ends
up executing the wrong text, dereferencing overwritten page tables or
corrupting the kexec kernels data.
Cure this by bringing the offlined CPUs out of MWAIT into HLT.
Write to the monitored cache line of each offline CPU, which makes MWAIT
resume execution. The written control word tells the offlined CPUs to issue
HLT, which does not have the MWAIT problem.
That does not help, if a stray NMI, MCE or SMI hits the offlined CPUs as
those make it come out of HLT.
A follow up change will put them into INIT, which protects at least against
NMI and SMI.
Fixes: ea53069231 ("x86, hotplug: Use mwait to offline a processor, fix the legacy case")
Reported-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Ashok Raj <ashok.raj@intel.com>
Reviewed-by: Ashok Raj <ashok.raj@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230615193330.492257119@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9c9987bf5 upstream.
Monitoring idletask::thread_info::flags in mwait_play_dead() has been an
obvious choice as all what is needed is a cache line which is not written
by other CPUs.
But there is a use case where a "dead" CPU needs to be brought out of
MWAIT: kexec().
This is required as kexec() can overwrite text, pagetables, stacks and the
monitored cacheline of the original kernel. The latter causes MWAIT to
resume execution which obviously causes havoc on the kexec kernel which
results usually in triple faults.
Use a dedicated per CPU storage to prepare for that.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ashok Raj <ashok.raj@intel.com>
Reviewed-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230615193330.434553750@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f5e7eb786 upstream.
Tony reported intermittent lockups on poweroff. His analysis identified the
wbinvd() in stop_this_cpu() as the culprit. This was added to ensure that
on SME enabled machines a kexec() does not leave any stale data in the
caches when switching from encrypted to non-encrypted mode or vice versa.
That wbinvd() is conditional on the SME feature bit which is read directly
from CPUID. But that readout does not check whether the CPUID leaf is
available or not. If it's not available the CPU will return the value of
the highest supported leaf instead. Depending on the content the "SME" bit
might be set or not.
That's incorrect but harmless. Making the CPUID readout conditional makes
the observed hangs go away, but it does not fix the underlying problem:
CPU0 CPU1
stop_other_cpus()
send_IPIs(REBOOT); stop_this_cpu()
while (num_online_cpus() > 1); set_online(false);
proceed... -> hang
wbinvd()
WBINVD is an expensive operation and if multiple CPUs issue it at the same
time the resulting delays are even larger.
But CPU0 already observed num_online_cpus() going down to 1 and proceeds
which causes the system to hang.
This issue exists independent of WBINVD, but the delays caused by WBINVD
make it more prominent.
Make this more robust by adding a cpumask which is initialized to the
online CPU mask before sending the IPIs and CPUs clear their bit in
stop_this_cpu() after the WBINVD completed. Check for that cpumask to
become empty in stop_other_cpus() instead of watching num_online_cpus().
The cpumask cannot plug all holes either, but it's better than a raw
counter and allows to restrict the NMI fallback IPI to be sent only the
CPUs which have not reported within the timeout window.
Fixes: 08f253ec37 ("x86/cpu: Clear SME feature flag when not in use")
Reported-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Ashok Raj <ashok.raj@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/3817d810-e0f1-8ef8-0bbd-663b919ca49b@cybernetics.com
Link: https://lore.kernel.org/r/87h6r770bv.ffs@tglx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c26bd4384 upstream,
If mas_store_gfp() in the gather loop failed, the 'error' variable that
ultimately gets returned was not being set. In many cases, its original
value of -ENOMEM was still in place, and that was fine. But if VMAs had
been split at the start or end of the range, then 'error' could be zero.
Change to the 'error = foo(); if (error) goto â¦' idiom to fix the bug.
Also clean up a later case which avoided the same bug by *explicitly*
setting error = -ENOMEM right before calling the function that might
return -ENOMEM.
In a final cosmetic change, move the 'Point of no return' comment to
*after* the goto. That's been in the wrong place since the preallocation
was removed, and this new error path was added.
Fixes: 606c812eb1 ("mm/mmap: Fix error path in do_vmi_align_munmap()")
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Cc: stable@vger.kernel.org
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 606c812eb1 upstream.
The error unrolling was leaving the VMAs detached in many cases and
leaving the locked_vm statistic altered, and skipping the unrolling
entirely in the case of the vma tree write failing.
Fix the error path by re-attaching the detached VMAs and adding the
necessary goto for the failed vma tree write, and fix the locked_vm
statistic by only updating after the vma tree write succeeds.
Fixes: 763ecb0350 ("mm: remove the vma linked list")
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[ dwmw2: Strictly, the original patch wasn't *re-attaching* the
detached VMAs. They *were* still attached but just had
the 'detached' flag set, which is an optimisation. Which
doesn't exist in 6.3, so drop that. Also drop the call
to vma_start_write() which came in with the per-VMA
locking in 6.4. ]
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6fe55c2799 upstream.
last component point filename struct. Currently putname is called after
vfs_path_parent_lookup(). And then last component is used for
lookup_one_qstr_excl(). name in last component is freed by previous
calling putname(). And It cause file lookup failure when testing
generic/464 test of xfstest.
Fixes: 74d7970feb ("ksmbd: fix racy issue from using ->d_parent and ->d_name")
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df14afeed2 upstream.
There is a case that file_present is true and path is uninitialized.
This patch change file_present is set to false by default and set to
true when patch is initialized.
Fixes: 74d7970feb ("ksmbd: fix racy issue from using ->d_parent and ->d_name")
Reported-by: Coverity Scan <scan-admin@coverity.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 48b47f0caa upstream.
Uninitialized rd.delegated_inode can be used in vfs_rename().
Fix this by setting rd.delegated_inode to NULL to avoid the uninitialized
read.
Fixes: 74d7970feb ("ksmbd: fix racy issue from using ->d_parent and ->d_name")
Reported-by: Coverity Scan <scan-admin@coverity.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1caa71a7a6 upstream.
When reworking the vgic locking, the vgic distributor registration
got simplified, which was a very good cleanup. But just a tad too
radical, as we now register the *native* vgic only, ignoring the
GICv2-on-GICv3 that allows pre-historic VMs (or so I thought)
to run.
As it turns out, QEMU still defaults to GICv2 in some cases, and
this breaks Nathan's setup!
Fix it by propagating the *requested* vgic type rather than the
host's version.
Fixes: 59112e9c39 ("KVM: arm64: vgic: Fix a circular locking issue")
Reported-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
link: https://lore.kernel.org/r/20230606221525.GA2269598@dev-arch.thelio-3990X
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 043d2acf57 upstream.
Otherwise the module reference counter is leaked.
Fixes b9703ed44f ("netfilter: nf_tables: support for adding new devices to an existing netdev chain")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 85d38d5810 ]
When booting with "intremap=off" and "x2apic_phys" on the kernel command
line, the physical x2APIC driver ends up being used even when x2APIC
mode is disabled ("intremap=off" disables x2APIC mode). This happens
because the first compound condition check in x2apic_phys_probe() is
false due to x2apic_mode == 0 and so the following one returns true
after default_acpi_madt_oem_check() having already selected the physical
x2APIC driver.
This results in the following panic:
kernel BUG at arch/x86/kernel/apic/io_apic.c:2409!
invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 6.4.0-rc2-ver4.1rc2 #2
Hardware name: Dell Inc. PowerEdge R6515/07PXPY, BIOS 2.3.6 07/06/2021
RIP: 0010:setup_IO_APIC+0x9c/0xaf0
Call Trace:
<TASK>
? native_read_msr
apic_intr_mode_init
x86_late_time_init
start_kernel
x86_64_start_reservations
x86_64_start_kernel
secondary_startup_64_no_verify
</TASK>
which is:
setup_IO_APIC:
apic_printk(APIC_VERBOSE, "ENABLING IO-APIC IRQs\n");
for_each_ioapic(ioapic)
BUG_ON(mp_irqdomain_create(ioapic));
Return 0 to denote that x2APIC has not been enabled when probing the
physical x2APIC driver.
[ bp: Massage commit message heavily. ]
Fixes: 9ebd680bd0 ("x86, apic: Use probe routines to simplify apic selection")
Signed-off-by: Dheeraj Kumar Srivastava <dheerajkumar.srivastava@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Kishon Vijay Abraham I <kvijayab@amd.com>
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Reviewed-by: Cyrill Gorcunov <gorcunov@gmail.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20230616212236.1389-1-dheerajkumar.srivastava@amd.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b9f174c811 ]
Commits ffb1b4a410 ("x86/unwind/orc: Add 'signal' field to ORC
metadata") and fb799447ae ("x86,objtool: Split UNWIND_HINT_EMPTY in
two") changed the ORC format. Although ORC is internal to the kernel,
it's the only way for external tools to get reliable kernel stack traces
on x86-64. In particular, the drgn debugger [1] uses ORC for stack
unwinding, and these format changes broke it [2]. As the drgn
maintainer, I don't care how often or how much the kernel changes the
ORC format as long as I have a way to detect the change.
It suffices to store a version identifier in the vmlinux and kernel
module ELF files (to use when parsing ORC sections from ELF), and in
kernel memory (to use when parsing ORC from a core dump+symbol table).
Rather than hard-coding a version number that needs to be manually
bumped, Peterz suggested hashing the definitions from orc_types.h. If
there is a format change that isn't caught by this, the hashing script
can be updated.
This patch adds an .orc_header allocated ELF section containing the
20-byte hash to vmlinux and kernel modules, along with the corresponding
__start_orc_header and __stop_orc_header symbols in vmlinux.
1: https://github.com/osandov/drgn
2: https://github.com/osandov/drgn/issues/303
Fixes: ffb1b4a410 ("x86/unwind/orc: Add 'signal' field to ORC metadata")
Fixes: fb799447ae ("x86,objtool: Split UNWIND_HINT_EMPTY in two")
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Josh Poimboeuf <jpoimboe@kernel.org>
Link: https://lkml.kernel.org/r/aef9c8dc43915b886a8c48509a12ec1b006ca1ca.1686690801.git.osandov@osandov.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f5d2e3bab ]
Fix possible virtqueue used buffers leak and corresponding stuck
in case of temporary -EIO from sendmsg() which is produced by
tun driver while backend device is not up.
In case of no-retriable error and zcopy do not revert upend_idx
to pass packet data (that is update used_idx in corresponding
vhost_zerocopy_signal_used()) as if packet data has been
transferred successfully.
v2: set vq->heads[ubuf->desc].len equal to VHOST_DMA_DONE_LEN
in case of fake successful transmit.
Signed-off-by: Andrey Smetanin <asmetanin@yandex-team.ru>
Message-Id: <20230424204411.24888-1-asmetanin@yandex-team.ru>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Andrey Smetanin <asmetanin@yandex-team.ru>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 376daf3177 ]
As is done in the net, iscsi, and vsock vhost support, let the vdpa vqs
know about the features that have been negotiated. This allows vhost
to more safely make decisions based on the features, such as when using
PACKED vs split queues.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20230424225031.18947-2-shannon.nelson@amd.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 982b173a6c ]
Userspace can race to free the gobj(robj converted from), robj should not
be accessed again after drm_gem_object_put, otherwith it will result in
use-after-free.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Min Li <lm0963hack@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48bfd02569 ]
If it is async, runqueue_node is freed in g2d_runqueue_worker on another
worker thread. So in extreme cases, if g2d_runqueue_worker runs first, and
then executes the following if statement, there will be use-after-free.
Signed-off-by: Min Li <lm0963hack@gmail.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a05955980 ]
Fix a wrong error return by dropping an error return.
When vidi driver is remvoed, if ctx->raw_edid isn't same as fake_edid_info
then only what we have to is to free ctx->raw_edid so that driver removing
can work correctly - it's not an error case.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1acfc6e753 ]
With IC_INTR_RX_FULL slave interrupt handler reads data in a loop until
RX FIFO is empty. When testing with the slave-eeprom, each transaction
has 2 bytes for address/index and 1 byte for value, the address byte
can be written as data byte due to dropping STOP condition.
In the test below, the master continuously writes to the slave, first 2
bytes are index, 3rd byte is value and follow by a STOP condition.
i2c_write: i2c-3 #0 a=04b f=0000 l=3 [00-D1-D1]
i2c_write: i2c-3 #0 a=04b f=0000 l=3 [00-D2-D2]
i2c_write: i2c-3 #0 a=04b f=0000 l=3 [00-D3-D3]
Upon receiving STOP condition slave eeprom would reset `idx_write_cnt` so
next 2 bytes can be treated as buffer index for upcoming transaction.
Supposedly the slave eeprom buffer would be written as
EEPROM[0x00D1] = 0xD1
EEPROM[0x00D2] = 0xD2
EEPROM[0x00D3] = 0xD3
When CPU load is high the slave irq handler may not read fast enough,
the interrupt status can be seen as 0x204 with both DW_IC_INTR_STOP_DET
(0x200) and DW_IC_INTR_RX_FULL (0x4) bits. The slave device may see
the transactions below.
0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1594 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1594 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1594 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1794 : INTR_STAT=0x204
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x1790 : INTR_STAT=0x200
0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1594 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1594 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1594 : INTR_STAT=0x4
After `D1` is received, read loop continues to read `00` which is the
first bype of next index. Since STOP condition is ignored by the loop,
eeprom buffer index increased to `D2` and `00` is written as value.
So the slave eeprom buffer becomes
EEPROM[0x00D1] = 0xD1
EEPROM[0x00D2] = 0x00
EEPROM[0x00D3] = 0xD3
The fix is to use `FIRST_DATA_BYTE` (bit 11) in `IC_DATA_CMD` to split
the transactions. The first index byte in this case would have bit 11
set. Check this indication to inject I2C_SLAVE_WRITE_REQUESTED event
which will reset `idx_write_cnt` in slave eeprom.
Signed-off-by: David Zheng <david.zheng@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ebfd881ab ]
Rather than casting pci1xxxx_i2c_shutdown to an incompatible function type,
update the type to match that expected by __devm_add_action.
Reported by clang-16 with W-1:
.../i2c-mchp-pci1xxxx.c:1159:29: error: cast from 'void (*)(struct pci1xxxx_i2c *)' to 'void (*)(void *)' converts to incompatible function type [-Werror,-Wcast-function-type-strict]
ret = devm_add_action(dev, (void (*)(void *))pci1xxxx_i2c_shutdown, i2c);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
./include/linux/device.h:251:29: note: expanded from macro 'devm_add_action'
__devm_add_action(release, action, data, #action)
^~~~~~
No functional change intended.
Compile tested only.
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Tharun Kumar P<tharunkumar.pasumarthi@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8cde87b007 ]
This patch fixes the following sparse warning:
net/sched/sch_api.c:2305:1: sparse: warning: symbol 'tc_skip_wrapper' was not declared. Should it be static?
No functional change intended.
Signed-off-by: Min-Hua Chen <minhuadotchen@gmail.com>
Acked-by: Pedro Tammela <pctammela@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 32cf0046a6 ]
There's an issue on SAI synchronous mode that TX/RX side can't get BCLK
from RX/TX it sync with if BYP bit is asserted. It's a workaround to
fix it that enable SION of IOMUX pad control and assert BCI.
For example if TX sync with RX which means both TX and RX are using clk
form RX and BYP=1. TX can get BCLK only if the following two conditions
are valid:
1. SION of RX BCLK IOMUX pad is set to 1
2. BCI of TX is set to 1
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Link: https://lore.kernel.org/r/20230530103012.3448838-1-chancel.liu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03c5c83b70 ]
Avoid linker error for randomly generated config file that
has CONFIG_BRANCH_PROFILE_NONE enabled and make it similar
to riscv, x86 and also to commit 4bf3ec384e ("s390: disable
branch profiling for vdso").
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa58cc888d ]
When a direct I/O write is performed, iomap_dio_rw() invalidates the
part of the page cache which the write is going to before carrying out
the write. In the odd case, the direct I/O write will be reading from
the same page it is writing to. gfs2 carries out writes with page
faults disabled, so it should have been obvious that this page
invalidation can cause iomap_dio_rw() to never make any progress.
Currently, gfs2 will end up in an endless retry loop in
gfs2_file_direct_write() instead, though.
Break this endless loop by limiting the number of retries and falling
back to buffered I/O after that.
Also simplify should_fault_in_pages() sightly and add a comment to make
the above case easier to understand.
Reported-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89c0c62e94 ]
Currently, if the device is offline and all the channel paths are
either configured or varied offline, the associated subchannel gets
unregistered. Don't unregister the subchannel, instead unregister
offline device.
Signed-off-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20a99a291d ]
Some devices have a wrong entry in their button array which points to
a GPIO which is required in another driver, so soc_button_array must
not claim it.
A specific example of this is the Lenovo Yoga Book X90F / X90L,
where the PNP0C40 home button entry points to a GPIO which is not
a home button and which is required by the lenovo-yogabook driver.
Add a DMI quirk table which can specify an ACPI GPIO resource index which
should be skipped; and add an entry for the Lenovo Yoga Book X90F / X90L
to this new DMI quirk table.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230414072116.4497-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7275ce6a5 ]
Upon keep alive completion, nvme_keep_alive_work is scheduled with the
same delay every time. If keep alive commands are completing slowly,
this may cause a keep alive timeout. The following trace illustrates the
issue, taking KATO = 8 and TBKAS off for simplicity:
1. t = 0: run nvme_keep_alive_work, send keep alive
2. t = ε: keep alive reaches controller, controller restarts its keep
alive timer
3. t = 4: host receives keep alive completion, schedules
nvme_keep_alive_work with delay 4
4. t = 8: run nvme_keep_alive_work, send keep alive
Here, a keep alive having RTT of 4 causes a delay of at least 8 - ε
between the controller receiving successive keep alives. With ε small,
the controller is likely to detect a keep alive timeout.
Fix this by calculating the RTT of the keep alive command, and adjusting
the scheduling delay of the next keep alive work accordingly.
Reported-by: Costa Sapuntzakis <costa@purestorage.com>
Reported-by: Randy Jennings <randyj@purestorage.com>
Signed-off-by: Uday Shankar <ushankar@purestorage.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 774a963651 ]
When a command completes, we set a flag which will skip sending a
keep alive at the next run of nvme_keep_alive_work when TBKAS is on.
However, if the command was submitted long ago, it's possible that
the controller may have also restarted its keep alive timer (as a
result of receiving the command) long ago. The following trace
demonstrates the issue, assuming TBKAS is on and KATO = 8 for
simplicity:
1. t = 0: submit I/O commands A, B, C, D, E
2. t = 0.5: commands A, B, C, D, E reach controller, restart its keep
alive timer
3. t = 1: A completes
4. t = 2: run nvme_keep_alive_work, see recent completion, do nothing
5. t = 3: B completes
6. t = 4: run nvme_keep_alive_work, see recent completion, do nothing
7. t = 5: C completes
8. t = 6: run nvme_keep_alive_work, see recent completion, do nothing
9. t = 7: D completes
10. t = 8: run nvme_keep_alive_work, see recent completion, do nothing
11. t = 9: E completes
At this point, 8.5 seconds have passed without restarting the
controller's keep alive timer, so the controller will detect a keep
alive timeout.
Fix this by checking the IO start time when deciding to defer sending a
keep alive command. Only set comp_seen if the command started after the
most recent run of nvme_keep_alive_work. With this change, the
completions of B, C, and D will not set comp_seen and the run of
nvme_keep_alive_work at t = 4 will send a keep alive.
Reported-by: Costa Sapuntzakis <costa@purestorage.com>
Reported-by: Randy Jennings <randyj@purestorage.com>
Signed-off-by: Uday Shankar <ushankar@purestorage.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea4d453b9e ]
With TBKAS on, the completion of one command can defer sending a
keep alive for up to twice the delay between successive runs of
nvme_keep_alive_work. The current delay of KATO / 2 thus makes it
possible for one command to defer sending a keep alive for up to
KATO, which can result in the controller detecting a KATO. The following
trace demonstrates the issue, taking KATO = 8 for simplicity:
1. t = 0: run nvme_keep_alive_work, no keep-alive sent
2. t = ε: I/O completion seen, set comp_seen = true
3. t = 4: run nvme_keep_alive_work, see comp_seen == true,
skip sending keep-alive, set comp_seen = false
4. t = 8: run nvme_keep_alive_work, see comp_seen == false,
send a keep-alive command.
Here, there is a delay of 8 - ε between receiving a command completion
and sending the next command. With ε small, the controller is likely to
detect a keep alive timeout.
Fix this by running nvme_keep_alive_work with a delay of KATO / 4
whenever TBKAS is on. Going through the above trace now gives us a
worst-case delay of 4 - ε, which is in line with the recommendation of
sending a command every KATO / 2 in the NVMe specification.
Reported-by: Costa Sapuntzakis <costa@purestorage.com>
Reported-by: Randy Jennings <randyj@purestorage.com>
Signed-off-by: Uday Shankar <ushankar@purestorage.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31a5978243 ]
In the function nvme_passthru_end(), only the value of the command
opcode is checked, without checking the command type (IO command or
Admin command). When we send a Dataset Management command (The opcode
of the Dataset Management command is the same as the Set Feature
command), kernel thinks it is a set feature command, then sets the
controller's keep alive interval, and calls nvme_keep_alive_work().
Signed-off-by: min15.li <min15.li@samsung.com>
Reviewed-by: Kanchan Joshi <joshi.k@samsung.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8fd9f4232d ]
This fixes the following warning reported by gcc 10.2.1 under x86_64:
../fs/btrfs/tree-log.c: In function ‘btrfs_log_inode’:
../fs/btrfs/tree-log.c:6211:9: error: ‘last_range_start’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
6211 | ret = insert_dir_log_key(trans, log, path, key.objectid,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
6212 | first_dir_index, last_dir_index);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../fs/btrfs/tree-log.c:6161:6: note: ‘last_range_start’ was declared here
6161 | u64 last_range_start;
| ^~~~~~~~~~~~~~~~
This might be a false positive fixed in later compiler versions but we
want to have it fixed.
Reported-by: k2ci <kernel-bot@kylinos.cn>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Shida Zhang <zhangshida@kylinos.cn>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b9e46aa07 ]
This patch fixes the error checking in nfcsim.c.
The DebugFS kernel API is developed in
a way that the caller can safely ignore the errors that
occur during the creation of DebugFS nodes.
Signed-off-by: Osama Muhammad <osmtendev@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73af6c7511 ]
When a message was received the last_initiator is set to 0xff.
This will force the signal free time for the next transmit
to that for a new initiator. However, if a new transmit is
already in progress, then don't set last_initiator, since
that's the initiator of the current transmit. Overwriting
this would cause the signal free time of a following transmit
to be that of the new initiator instead of a next transmit.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe4526d99e ]
Explicitly disable the CEC adapter in cec_devnode_unregister()
Usually this does not really do anything important, but for drivers
that use the CEC pin framework this is needed to properly stop the
hrtimer. Without this a crash would happen when such a driver is
unloaded with rmmod.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 16a9c24f24 ]
Added a variable check and
transition in case of an error
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Denis Arefev <arefev@swemel.ru>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a737d3b8c ]
The tpg->np_login_sem is a semaphore that is used to serialize the login
process when multiple login threads run concurrently against the same
target portal group.
The iscsi_target_locate_portal() function finds the tpg, calls
iscsit_access_np() against the np_login_sem semaphore and saves the tpg
pointer in conn->tpg;
If iscsi_target_locate_portal() fails, the caller will check for the
conn->tpg pointer and, if it's not NULL, then it will assume that
iscsi_target_locate_portal() called iscsit_access_np() on the semaphore.
Make sure that conn->tpg gets initialized only if iscsit_access_np() was
successful, otherwise iscsit_deaccess_np() may end up being called against
a semaphore we never took, allowing more than one thread to access the same
tpg.
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Link: https://lore.kernel.org/r/20230508162219.1731964-4-mlombard@redhat.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 13247018d6 ]
If the initiator suddenly stops sending data during a login while keeping
the TCP connection open, the login_work won't be scheduled and will never
release the login semaphore; concurrent login operations will therefore get
stuck and fail.
The bug is due to the inability of the login timeout code to properly
handle this particular case.
Fix the problem by replacing the old per-NP login timer with a new
per-connection timer.
The timer is started when an initiator connects to the target; if it
expires, it sends a SIGINT signal to the thread pointed at by the
conn->login_kworker pointer.
conn->login_kworker is set by calling the iscsit_set_login_timer_kworker()
helper, initially it will point to the np thread; When the login
operation's control is in the process of being passed from the NP-thread to
login_work, the conn->login_worker pointer is set to NULL. Finally,
login_kworker will be changed to point to the worker thread executing the
login_work job.
If conn->login_kworker is NULL when the timer expires, it means that the
login operation hasn't been completed yet but login_work isn't running, in
this case the timer will mark the login process as failed and will schedule
login_work so the latter will be forced to free the resources it holds.
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Link: https://lore.kernel.org/r/20230508162219.1731964-2-mlombard@redhat.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff7a1790fb ]
Up until commit 6a45b0e258 ("gpiolib: Introduce
gpiochip_irqchip_add_domain()") all irq_domains were allocated
by gpiolib itself and thus gpiolib also takes care of freeing it.
With gpiochip_irqchip_add_domain() a user of gpiolib can associate an
irq_domain with the gpio_chip. This irq_domain is not managed by
gpiolib and therefore must not be freed by gpiolib.
Fixes: 6a45b0e258 ("gpiolib: Introduce gpiochip_irqchip_add_domain()")
Reported-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1bcb976d8 ]
Add the missing check for platform_get_irq() and return error code
if it fails.
The returned error code will be dealed with in
builtin_platform_driver(sifive_gpio_driver) and the driver will not
be registered.
Fixes: f52d6d8b43 ("gpio: sifive: To get gpio irq offset from device tree data")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c00914e54 ]
In case of gpio-regmap, IRQ chip is added by regmap-irq and associated with
GPIO chip by gpiochip_irqchip_add_domain(). The initialization flag was not
added in gpiochip_irqchip_add_domain(), causing gpiochip_to_irq() to return
-EPROBE_DEFER.
Fixes: 5467801f1f ("gpio: Restrict usage of GPIO chip irq members before initialization")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf9ae4a007 ]
In pre-production prototypes (of which I only know one person
having one, Peter Geis), GPIO0 pin A5 was tied to the SDMMC
power enable pin on the CM4 connector. On all production models,
this is not the case; instead, this pin is used for the nEXTRST
signal, and the SDMMC power enable pin is always pulled high.
Since everyone currently using the SOQuartz device trees will
want this change, it is made to the tree without splitting the
trees into two separate ones of which users will then inevitably
choose the wrong one.
This fixes USB and PCIe on a wide variety of CM4IO-compatible
boards which use the nEXTRST signal.
Fixes: 5859b5a9c3 ("arm64: dts: rockchip: add SoQuartz CM4IO dts")
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Link: https://lore.kernel.org/r/20230421152610.21688-1-frattaroli.nicolas@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9628e8877 ]
This reverts commit 1f86123b97 ("net: align SO_RCVMARK required
privileges with SO_MARK") because the reasoning in the commit message
is not really correct:
SO_RCVMARK is used for 'reading' incoming skb mark (via cmsg), as such
it is more equivalent to 'getsockopt(SO_MARK)' which has no priv check
and retrieves the socket mark, rather than 'setsockopt(SO_MARK) which
sets the socket mark and does require privs.
Additionally incoming skb->mark may already be visible if
sysctl_fwmark_reflect and/or sysctl_tcp_fwmark_accept are enabled.
Furthermore, it is easier to block the getsockopt via bpf
(either cgroup setsockopt hook, or via syscall filters)
then to unblock it if it requires CAP_NET_RAW/ADMIN.
On Android the socket mark is (among other things) used to store
the network identifier a socket is bound to. Setting it is privileged,
but retrieving it is not. We'd like unprivileged userspace to be able
to read the network id of incoming packets (where mark is set via
iptables [to be moved to bpf])...
An alternative would be to add another sysctl to control whether
setting SO_RCVMARK is privilged or not.
(or even a MASK of which bits in the mark can be exposed)
But this seems like over-engineering...
Note: This is a non-trivial revert, due to later merged commit e42c7beee7
("bpf: net: Consider has_current_bpf_ctx() when testing capable() in sk_setsockopt()")
which changed both 'ns_capable' into 'sockopt_ns_capable' calls.
Fixes: 1f86123b97 ("net: align SO_RCVMARK required privileges with SO_MARK")
Cc: Larysa Zaremba <larysa.zaremba@intel.com>
Cc: Simon Horman <simon.horman@corigine.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Eyal Birger <eyal.birger@gmail.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Patrick Rohr <prohr@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20230618103130.51628-1-maze@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7c059fba6 ]
When mirroring to a gretap in hardware the device expects to be
programmed with the egress port and all the encapsulating headers. This
requires the driver to resolve the path the packet will take in the
software data path and program the device accordingly.
If the path cannot be resolved (in this case because of an unresolved
neighbor), then mirror installation fails until the path is resolved.
This results in a race that causes the test to sometimes fail.
Fix this by setting the neighbor's state to permanent in a couple of
tests, so that it is always valid.
Fixes: 35c31d5c32 ("selftests: forwarding: Test mirror-to-gretap w/ UL 802.1d")
Fixes: 239e754af8 ("selftests: forwarding: Test mirror-to-gretap w/ UL 802.1q")
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/268816ac729cb6028c7a34d4dda6f4ec7af55333.1687264607.git.petrm@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26fed83653 ]
Rather than assign the user pointer to msghdr->msg_control, assign it
to msghdr->msg_control_user to make sparse happy. They are in a union
so the end result is the same, but let's avoid new sparse warnings and
squash this one.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202306210654.mDMcyMuB-lkp@intel.com/
Fixes: cac9e4418f ("io_uring/net: save msghdr->msg_control for retries")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db8eae6bc5 ]
We currently allow to create perf link for program with
expected_attach_type == BPF_TRACE_KPROBE_MULTI.
This will cause crash when we call helpers like get_attach_cookie or
get_func_ip in such program, because it will call the kprobe_multi's
version (current->bpf_ctx context setup) of those helpers while it
expects perf_link's current->bpf_ctx context setup.
Making sure that we use BPF_TRACE_KPROBE_MULTI expected_attach_type
only for programs attaching through kprobe_multi link.
Fixes: ca74823c6e ("bpf: Add cookie support to programs attached with kprobe multi link")
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20230618131414.75649-1-jolsa@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9724160b39 ]
When building a kernel with LLVM=1, LLVM_IAS=0 and CONFIG_KASAN=y, LLVM
leaves DWARF tags for the "asan.module_ctor" & co symbols. In turn,
pahole creates BTF_KIND_FUNC entries for these and this makes the BTF
metadata validation fail because they contain a dot.
In a dramatic turn of event, this BTF verification failure can cause
the netfilter_bpf initialization to fail, causing netfilter_core to
free the netfilter_helper hashmap and netfilter_ftp to trigger a
use-after-free. The risk of u-a-f in netfilter will be addressed
separately but the existence of "asan.module_ctor" debug info under some
build conditions sounds like a good enough reason to accept functions
that contain dots in BTF.
Although using only LLVM=1 is the recommended way to compile clang-based
kernels, users can certainly do LLVM=1, LLVM_IAS=0 as well and we still
try to support that combination according to Nick. To clarify:
- > v5.10 kernel, LLVM=1 (LLVM_IAS=0 is not the default) is recommended,
but user can still have LLVM=1, LLVM_IAS=0 to trigger the issue
- <= 5.10 kernel, LLVM=1 (LLVM_IAS=0 is the default) is recommended in
which case GNU as will be used
Fixes: 1dc9285184 ("bpf: kernel side support for BTF Var and DataSec")
Signed-off-by: Florent Revest <revest@chromium.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Cc: Yonghong Song <yhs@meta.com>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/bpf/20230615145607.3469985-1-revest@chromium.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62f9a68a36 ]
Move the alias from xt_osf to nfnetlink_osf.
Fixes: f932495208 ("netfilter: nfnetlink_osf: extract nfnetlink_subsystem code from xt_osf.c")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62e1e94b24 ]
Use binding list to track set transaction and to check for unbound
chains before entering the commit phase.
Bail out if chain binding remain unused before entering the commit
step.
Fixes: d0e2c7de92 ("netfilter: nf_tables: add NFT_CHAIN_BINDING")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 938154b93b ]
Add a new list to track set transaction and to check for unbound
anonymous sets before entering the commit phase.
Bail out at the end of the transaction handling if an anonymous set
remains unbound.
Fixes: 96518518cc ("netfilter: add nftables")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c88c535b59 ]
Anonymous sets come with NFT_SET_CONSTANT from userspace. Although API
allows to create anonymous sets without NFT_SET_CONSTANT, it makes no
sense to allow to add and to delete elements for bound anonymous sets.
Fixes: 96518518cc ("netfilter: add nftables")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b84e215f8 ]
The .walk callback iterates over the current active set, but it might be
useful to iterate over the next generation set. Use the generation mask
to determine what set view (either current or next generation) is use
for the walk iteration.
Fixes: 3c4287f620 ("nf_tables: Add set type for arbitrary concatenation of ranges")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 628bd3e49c ]
set .destroy callback releases the references to other objects in maps.
This is very late and it results in spurious EBUSY errors. Drop refcount
from the preparation phase instead, update set backend not to drop
reference counter from set .destroy path.
Exceptions: NFT_TRANS_PREPARE_ERROR does not require to drop the
reference counter because the transaction abort path releases the map
references for each element since the set is unbound. The abort path
also deals with releasing reference counter for new elements added to
unbound sets.
Fixes: 591054469b ("netfilter: nf_tables: revisit chain/object refcounting from elements")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26b5a5712e ]
Add a new state to deal with rule expressions deactivation from the
newrule error path, otherwise the anonymous set remains in the list in
inactive state for the next generation. Mark the set/chain transaction
as unbound so the abort path releases this object, set it as inactive in
the next generation so it is not reachable anymore from this transaction
and reference counter is dropped.
Fixes: 1240eb93f0 ("netfilter: nf_tables: incorrect error path handling with NFT_MSG_NEWRULE")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4bedf9eee0 ]
Add bound flag to rule and chain transactions as in 6a0a8d10a3
("netfilter: nf_tables: use-after-free in failing rule with bound set")
to skip them in case that the chain is already bound from the abort
path.
This patch fixes an imbalance in the chain use refcnt that triggers a
WARN_ON on the table and chain destroy path.
This patch also disallows nested chain bindings, which is not
supported from userspace.
The logic to deal with chain binding in nft_data_hold() and
nft_data_release() is not correct. The NFT_TRANS_PREPARE state needs a
special handling in case a chain is bound but next expressions in the
same rule fail to initialize as described by 1240eb93f0 ("netfilter:
nf_tables: incorrect error path handling with NFT_MSG_NEWRULE").
The chain is left bound if rule construction fails, so the objects
stored in this chain (and the chain itself) are released by the
transaction records from the abort path, follow up patch ("netfilter:
nf_tables: add NFT_TRANS_PREPARE_ERROR to deal with bound set/chain")
completes this error handling.
When deleting an existing rule, chain bound flag is set off so the
rule expression .destroy path releases the objects.
Fixes: d0e2c7de92 ("netfilter: nf_tables: add NFT_CHAIN_BINDING")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7580e0a78e ]
We have seen a bug where the NIC incorrectly changes the length in the
IP header of a padded packet to include the padding bytes. The driver
already has a workaround for this so do the workaround for this NIC too.
This resolves the issue.
The NIC in question identifies itself as follows:
[ 8.828494] be2net 0000:02:00.0: FW version is 10.7.110.31
[ 8.834759] be2net 0000:02:00.0: Emulex OneConnect(be3): PF FLEX10 port 1
02:00.0 Ethernet controller: Emulex Corporation OneConnect 10Gb NIC (be3) (rev 01)
Fixes: ca34fe38f0 ("be2net: fix wrong usage of adapter->generation")
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Link: https://lore.kernel.org/r/20230616164549.2863037-1-ross.lagerwall@citrix.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b79d7c14f4 ]
Since the introduction of the OF bindings, DSA has always had a policy that
in case multiple CPU ports are present in the device tree, the numerically
smallest one is always chosen.
The MT7530 switch family, except the switch on the MT7988 SoC, has 2 CPU
ports, 5 and 6, where port 6 is preferable on the MT7531BE switch because
it has higher bandwidth.
The MT7530 driver developers had 3 options:
- to modify DSA when the MT7531 switch support was introduced, such as to
prefer the better port
- to declare both CPU ports in device trees as CPU ports, and live with the
sub-optimal performance resulting from not preferring the better port
- to declare just port 6 in the device tree as a CPU port
Of course they chose the path of least resistance (3rd option), kicking the
can down the road. The hardware description in the device tree is supposed
to be stable - developers are not supposed to adopt the strategy of
piecemeal hardware description, where the device tree is updated in
lockstep with the features that the kernel currently supports.
Now, as a result of the fact that they did that, any attempts to modify the
device tree and describe both CPU ports as CPU ports would make DSA change
its default selection from port 6 to 5, effectively resulting in a
performance degradation visible to users with the MT7531BE switch as can be
seen below.
Without preferring port 6:
[ ID][Role] Interval Transfer Bitrate Retr
[ 5][TX-C] 0.00-20.00 sec 374 MBytes 157 Mbits/sec 734 sender
[ 5][TX-C] 0.00-20.00 sec 373 MBytes 156 Mbits/sec receiver
[ 7][RX-C] 0.00-20.00 sec 1.81 GBytes 778 Mbits/sec 0 sender
[ 7][RX-C] 0.00-20.00 sec 1.81 GBytes 777 Mbits/sec receiver
With preferring port 6:
[ ID][Role] Interval Transfer Bitrate Retr
[ 5][TX-C] 0.00-20.00 sec 1.99 GBytes 856 Mbits/sec 273 sender
[ 5][TX-C] 0.00-20.00 sec 1.99 GBytes 855 Mbits/sec receiver
[ 7][RX-C] 0.00-20.00 sec 1.72 GBytes 737 Mbits/sec 15 sender
[ 7][RX-C] 0.00-20.00 sec 1.71 GBytes 736 Mbits/sec receiver
Using one port for WAN and the other ports for LAN is a very popular use
case which is what this test emulates.
As such, this change proposes that we retroactively modify stable kernels
(which don't support the modification of the CPU port assignments, so as to
let user space fix the problem and restore the throughput) to keep the
mt7530 driver preferring port 6 even with device trees where the hardware
is more fully described.
Fixes: c288575f78 ("net: dsa: mt7530: Add the support of MT7531 switch")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8332cf6fd7 ]
LLDP frames are link-local frames, therefore they must be trapped to the
CPU port. Currently, the MT753X switches treat LLDP frames as regular
multicast frames, therefore flooding them to user ports. To fix this, set
LLDP frames to be trapped to the CPU port(s).
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7c6607355 ]
BPDUs are link-local frames, therefore they must be trapped to the CPU
port. Currently, the MT7530 switch treats BPDUs as regular multicast
frames, therefore flooding them to user ports. To fix this, set BPDUs to be
trapped to the CPU port. Group this on mt7530_setup() and
mt7531_setup_common() into mt753x_trap_frames() and call that.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ae90f90e4 ]
All MT7530 switch IP variants share the MT7530_MFC register, but the
current driver only writes it for the switch variant that is integrated in
the MT7621 SoC. Modify the code to include all MT7530 derivatives.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7fce52fdf ]
When using encapsulation the original packet's headers are copied to the
inner headers. This preserves the space for an inner mac header, which
is not used by the inner payloads for the encapsulation types supported
by IPVS. If a packet is using GUE or GRE encapsulation and needs to be
segmented, flow can be passed to __skb_udp_tunnel_segment() which
calculates a negative tunnel header length. A negative tunnel header
length causes pskb_may_pull() to fail, dropping the packet.
This can be observed by attaching probes to ip_vs_in_hook(),
__dev_queue_xmit(), and __skb_udp_tunnel_segment():
perf probe --add '__dev_queue_xmit skb->inner_mac_header \
skb->inner_network_header skb->mac_header skb->network_header'
perf probe --add '__skb_udp_tunnel_segment:7 tnl_hlen'
perf probe -m ip_vs --add 'ip_vs_in_hook skb->inner_mac_header \
skb->inner_network_header skb->mac_header skb->network_header'
These probes the headers and tunnel header length for packets which
traverse the IPVS encapsulation path. A TCP packet can be forced into
the segmentation path by being smaller than a calculated clamped MSS,
but larger than the advertised MSS.
probe:ip_vs_in_hook: inner_mac_header=0x0 inner_network_header=0x0 mac_header=0x44 network_header=0x52
probe:ip_vs_in_hook: inner_mac_header=0x44 inner_network_header=0x52 mac_header=0x44 network_header=0x32
probe:dev_queue_xmit: inner_mac_header=0x44 inner_network_header=0x52 mac_header=0x44 network_header=0x32
probe:__skb_udp_tunnel_segment_L7: tnl_hlen=-2
When using veth-based encapsulation, the interfaces are set to be
mac-less, which does not preserve space for an inner mac header. This
prevents this issue from occurring.
In our real-world testing of sending a 32KB file we observed operation
time increasing from ~75ms for veth-based encapsulation to over 1.5s
using IPVS encapsulation due to retries from dropped packets.
This changeset modifies the packet on the encapsulation path in
ip_vs_tunnel_xmit() and ip_vs_tunnel_xmit_v6() to remove the inner mac
header offset. This fixes UDP segmentation for both encapsulation types,
and corrects the inner headers for any IPIP flows that may use it.
Fixes: 84c0d5e96f ("ipvs: allow tunneling with gue encapsulation")
Signed-off-by: Terin Stock <terin@cloudflare.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Simon Horman <horms@kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92717c2356 ]
In case the QCA7000 is not available via SPI (e.g. in reset),
the driver will cause a high load. The reason for this is
that the synchronization is never finished and schedule()
is never called. Since the synchronization is not timing
critical, it's safe to drop this from the scheduling condition.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: 291ab06ecf ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4aaf2c5283 ]
When running workloads heavy unbalanced towards TX (high TX, low RX
traffic), sfc driver can retain the CPU during too long times. Although
in many cases this is not enough to be visible, it can affect
performance and system responsiveness.
A way to reproduce it is to use a debug kernel and run some parallel
netperf TX tests. In some systems, this will lead to this message being
logged:
kernel:watchdog: BUG: soft lockup - CPU#12 stuck for 22s!
The reason is that sfc driver doesn't account any NAPI budget for the TX
completion events work. With high-TX/low-RX traffic, this makes that the
CPU is held for long time for NAPI poll.
Documentations says "drivers can process completions for any number of Tx
packets but should only process up to budget number of Rx packets".
However, many drivers do limit the amount of TX completions that they
process in a single NAPI poll.
In the same way, this patch adds a limit for the TX work in sfc. With
the patch applied, the watchdog warning never appears.
Tested with netperf in different combinations: single process / parallel
processes, TCP / UDP and different sizes of UDP messages. Repeated the
tests before and after the patch, without any noticeable difference in
network or CPU performance.
Test hardware:
Intel(R) Xeon(R) CPU E5-1620 v4 @ 3.50GHz (4 cores, 2 threads/core)
Solarflare Communications XtremeScale X2522-25G Network Adapter
Fixes: 5227ecccea ("sfc: remove tx and MCDI handling from NAPI budget consideration")
Fixes: d19a537218 ("sfc_ef100: TX path for EF100 NICs")
Reported-by: Fei Liu <feliu@redhat.com>
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Link: https://lore.kernel.org/r/20230615084929.10506-1-ihuguet@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef4c5afc78 ]
When TUNNEL_L3_TO_L2 decap action was created, a pointer to a local
variable was passed as its HW action data, resulting in attempt to
free invalid address:
BUG: KASAN: invalid-free in mlx5dr_action_destroy+0x318/0x410 [mlx5_core]
Fixes: 4781df92f4 ("net/mlx5: DR, Move STEv0 modify header logic")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f015b900bc ]
With offloading enabled, esp_xmit() gets invoked very late, from within
validate_xmit_xfrm() which is after validate_xmit_skb() validates and
linearizes the skb if the underlying device does not support fragments.
esp_output_tail() may add a fragment to the skb while adding the auth
tag/ IV. Devices without the proper support will then send skb->data
points to with the correct length so the packet will have garbage at the
end. A pcap sniffer will claim that the proper data has been sent since
it parses the skb properly.
It is not affected with INET_ESP_OFFLOAD disabled.
Linearize the skb after offloading if the sending hardware requires it.
It was tested on v4, v6 has been adopted.
Fixes: 7785bba299 ("esp: Add a software GRO codepath")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7a2fc1437 ]
There are some MD5 tests which fail when the kernel is in FIPS mode,
since MD5 is not FIPS compliant. Add a check and only run those tests
if FIPS mode is not enabled.
Fixes: f0bee1ebb5 ("fcnal-test: Add TCP MD5 tests")
Fixes: 5cad8bce26 ("fcnal-test: Add TCP MD5 tests for VRF")
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Magali Lemes <magali.lemes@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb43c60e64 ]
The vrf-xfrm-tests tests use the hmac(md5) and cbc(des3_ede)
algorithms for performing authentication and encryption, respectively.
This causes the tests to fail when fips=1 is set, since these algorithms
are not allowed in FIPS mode. Therefore, switch from hmac(md5) and
cbc(des3_ede) to hmac(sha1) and cbc(aes), which are FIPS compliant.
Fixes: 3f251d7411 ("selftests: Add tests for vrf and xfrms")
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Magali Lemes <magali.lemes@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d113c395c6 ]
TLS selftests use the ChaCha20-Poly1305 and SM4 algorithms, which are not
FIPS compliant. When fips=1, this set of tests fails. Add a check and only
run these tests if not in FIPS mode.
Fixes: 4f336e88a8 ("selftests/tls: add CHACHA20-POLY1305 to tls selftests")
Fixes: e506342a03 ("selftests/tls: add SM4 GCM/CCM to tls selftests")
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Magali Lemes <magali.lemes@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad96f1c913 ]
The sysctl net/core/bpf_jit_enable does not work now due to commit
1022a5498f ("bpf, x86_64: Use bpf_jit_binary_pack_alloc"). The
commit saved the jitted insns into 'rw_image' instead of 'image'
which caused bpf_jit_dump not dumping proper content.
With 'echo 2 > /proc/sys/net/core/bpf_jit_enable', run
'./test_progs -t fentry_test'. Without this patch, one of jitted
image for one particular prog is:
flen=17 proglen=92 pass=4 image=0000000014c64883 from=test_progs pid=1807
00000000: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc
00000010: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc
00000020: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc
00000030: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc
00000040: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc
00000050: cc cc cc cc cc cc cc cc cc cc cc cc
With this patch, the jitte image for the same prog is:
flen=17 proglen=92 pass=4 image=00000000b90254b7 from=test_progs pid=1809
00000000: f3 0f 1e fa 0f 1f 44 00 00 66 90 55 48 89 e5 f3
00000010: 0f 1e fa 31 f6 48 8b 57 00 48 83 fa 07 75 2b 48
00000020: 8b 57 10 83 fa 09 75 22 48 8b 57 08 48 81 e2 ff
00000030: 00 00 00 48 83 fa 08 75 11 48 8b 7f 18 be 01 00
00000040: 00 00 48 83 ff 0a 74 02 31 f6 48 bf 18 d0 14 00
00000050: 00 c9 ff ff 48 89 77 00 31 c0 c9 c3
Fixes: 1022a5498f ("bpf, x86_64: Use bpf_jit_binary_pack_alloc")
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/bpf/20230609005439.3173569-1-yhs@fb.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 713274f1f2 ]
The following scenario describes a bug in the verifier where it
incorrectly concludes about equivalent scalar IDs which could lead to
verifier bypass in privileged mode:
1. Prepare a 32-bit rogue number.
2. Put the rogue number into the upper half of a 64-bit register, and
roll a random (unknown to the verifier) bit in the lower half. The
rest of the bits should be zero (although variations are possible).
3. Assign an ID to the register by MOVing it to another arbitrary
register.
4. Perform a 32-bit spill of the register, then perform a 32-bit fill to
another register. Due to a bug in the verifier, the ID will be
preserved, although the new register will contain only the lower 32
bits, i.e. all zeros except one random bit.
At this point there are two registers with different values but the same
ID, which means the integrity of the verifier state has been corrupted.
5. Compare the new 32-bit register with 0. In the branch where it's
equal to 0, the verifier will believe that the original 64-bit
register is also 0, because it has the same ID, but its actual value
still contains the rogue number in the upper half.
Some optimizations of the verifier prevent the actual bypass, so
extra care is needed: the comparison must be between two registers,
and both branches must be reachable (this is why one random bit is
needed). Both branches are still suitable for the bypass.
6. Right shift the original register by 32 bits to pop the rogue number.
7. Use the rogue number as an offset with any pointer. The verifier will
believe that the offset is 0, while in reality it's the given number.
The fix is similar to the 32-bit BPF_MOV handling in check_alu_op for
SCALAR_VALUE. If the spill is narrowing the actual register value, don't
keep the ID, make sure it's reset to 0.
Fixes: 354e8f1970 ("bpf: Support <8-byte scalar spill and refill")
Signed-off-by: Maxim Mikityanskiy <maxim@isovalent.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Andrii Nakryiko <andrii@kernel.org> # Checked veristat delta
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20230607123951.558971-2-maxtram95@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf06fcf4be ]
Offloaded policies are deleted through two flows: netdev is going
down and policy flush.
In both cases, the code lacks relevant call to delete offloaded policy.
Fixes: 919e43fad5 ("xfrm: add an interface to offload policy")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8681f71759 ]
Restore the host's PMUSERENR_EL0 value instead of clearing it,
before returning back to userspace, as the host's EL0 might have
a direct access to PMU registers (some bits of PMUSERENR_EL0 for
might not be zero for the host EL0).
Fixes: 83a7a4d643 ("arm64: perf: Enable PMU counter userspace access for perf event")
Signed-off-by: Reiji Watanabe <reijiw@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230603025035.3781797-2-reijiw@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a287f5b0cf ]
This change adds methods in the XFRM-I input path that ensures that
policies are checked prior to processing of the subsequent decapsulated
packet, after which the relevant policies may no longer be resolvable
(due to changing src/dst/proto/etc).
Notably, raw ESP/AH packets did not perform policy checks inherently,
whereas all other encapsulated packets (UDP, TCP encapsulated) do policy
checks after calling xfrm_input handling in the respective encapsulation
layer.
Fixes: b0355dbbf1 ("Fix XFRM-I support for nested ESP tunnels")
Test: Verified with additional Android Kernel Unit tests
Test: Verified against Android CTS
Signed-off-by: Benedict Wong <benedictwong@google.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f8b6df6a9 ]
This change allows inbound traffic through nested IPsec tunnels to
successfully match policies and templates, while retaining the secpath
stack trace as necessary for netfilter policies.
Specifically, this patch marks secpath entries that have already matched
against a relevant policy as having been verified, allowing it to be
treated as optional and skipped after a tunnel decapsulation (during
which the src/dst/proto/etc may have changed, and the correct policy
chain no long be resolvable).
This approach is taken as opposed to the iteration in b0355dbbf1,
where the secpath was cleared, since that breaks subsequent validations
that rely on the existence of the secpath entries (netfilter policies, or
transport-in-tunnel mode, where policies remain resolvable).
Fixes: b0355dbbf1 ("Fix XFRM-I support for nested ESP tunnels")
Test: Tested against Android Kernel Unit Tests
Test: Tested against Android CTS
Signed-off-by: Benedict Wong <benedictwong@google.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d082d48737 upstream.
KPTI keeps around two PGDs: one for userspace and another for the
kernel. Among other things, set_pgd() contains infrastructure to
ensure that updates to the kernel PGD are reflected in the user PGD
as well.
One side-effect of this is that set_pgd() expects to be passed whole
pages. Unfortunately, init_trampoline_kaslr() passes in a single entry:
'trampoline_pgd_entry'.
When KPTI is on, set_pgd() will update 'trampoline_pgd_entry' (an
8-Byte globally stored [.bss] variable) and will then proceed to
replicate that value into the non-existent neighboring user page
(located +4k away), leading to the corruption of other global [.bss]
stored variables.
Fix it by directly assigning 'trampoline_pgd_entry' and avoiding
set_pgd().
[ dhansen: tweak subject and changelog ]
Fixes: 0925dda596 ("x86/mm/KASLR: Use only one PUD entry for real mode trampoline")
Suggested-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/all/20230614163859.924309-1-lee@kernel.org/g
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ef7dfac51d upstream.
We selectively grab the ctx->uring_lock for poll update/removal, but
we really should grab it from the start to fully synchronize with
linked timeouts. Normally this is indeed the case, but if requests
are forced async by the application, we don't fully cover removal
and timer disarm within the uring_lock.
Make this simpler by having consistent locking state for poll removal.
Cc: stable@vger.kernel.org # 6.1+
Reported-by: Querijn Voet <querijnqyn@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 74d7970feb ]
Al pointed out that ksmbd has racy issue from using ->d_parent and ->d_name
in ksmbd_vfs_unlink and smb2_vfs_rename(). and use new lock_rename_child()
to lock stable parent while underlying rename racy.
Introduce vfs_path_parent_lookup helper to avoid out of share access and
export vfs functions like the following ones to use
vfs_path_parent_lookup().
- rename __lookup_hash() to lookup_one_qstr_excl().
- export lookup_one_qstr_excl().
- export getname_kernel() and putname().
vfs_path_parent_lookup() is used for parent lookup of destination file
using absolute pathname given from FILE_RENAME_INFORMATION request.
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Stable-dep-of: 40b268d384 ("ksmbd: add mnt_want_write to ksmbd vfs functions")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9bc37e0482 ]
Pass the dentry of a source file and the dentry of a destination directory
to lock parent inodes for rename. As soon as this function returns,
->d_parent of the source file dentry is stable and inodes are properly
locked for calling vfs-rename. This helper is needed for ksmbd server.
rename request of SMB protocol has to rename an opened file, no matter
which directory it's in.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Stable-dep-of: 40b268d384 ("ksmbd: add mnt_want_write to ksmbd vfs functions")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8e796895e ]
The max_raw_write member of the regmap_spi_avmm_bus structure is defined
as:
.max_raw_write = SPI_AVMM_VAL_SIZE * MAX_WRITE_CNT
SPI_AVMM_VAL_SIZE == 4 and MAX_WRITE_CNT == 1 so this results in a
maximum write transfer size of 4 bytes which provides only enough space to
transfer the address of the target register. It provides no space for the
value to be transferred. This bug became an issue (divide-by-zero in
_regmap_raw_write()) after the following was accepted into mainline:
commit 3981514180 ("regmap: Account for register length when chunking")
Change max_raw_write to include space (4 additional bytes) for both the
register address and value:
.max_raw_write = SPI_AVMM_REG_SIZE + SPI_AVMM_VAL_SIZE * MAX_WRITE_CNT
Fixes: 7f9fb67358 ("regmap: add Intel SPI Slave to AVMM Bus Bridge support")
Reviewed-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Russ Weight <russell.h.weight@intel.com>
Link: https://lore.kernel.org/r/20230620202824.380313-1-russell.h.weight@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0108a4e9f3 upstream.
When subprograms are in use, the main program is not jit'd after the
subprograms because jit_subprogs sets a value for prog->bpf_func upon
success. Subsequent calls to the JIT are bypassed when this value is
non-NULL. This leads to a situation where the main program and its
func[0] counterpart are both in the bpf kallsyms tree, but only func[0]
has an extable. Extables are only created during JIT. Now there are
two nearly identical program ksym entries in the tree, but only one has
an extable. Depending upon how the entries are placed, there's a chance
that a fault will call search_extable on the aux with the NULL entry.
Since jit_subprogs already copies state from func[0] to the main
program, include the extable pointer in this state duplication.
Additionally, ensure that the copy of the main program in func[0] is not
added to the bpf_prog_kallsyms table. Instead, let the main program get
added later in bpf_prog_load(). This ensures there is only a single
copy of the main program in the kallsyms table, and that its tag matches
the tag observed by tooling like bpftool.
Cc: stable@vger.kernel.org
Fixes: 1c2a088a66 ("bpf: x64: add JIT support for multi-function programs")
Signed-off-by: Krister Johansen <kjlx@templeofstupid.com>
Acked-by: Yonghong Song <yhs@fb.com>
Acked-by: Ilya Leoshkevich <iii@linux.ibm.com>
Tested-by: Ilya Leoshkevich <iii@linux.ibm.com>
Link: https://lore.kernel.org/r/6de9b2f4b4724ef56efbb0339daaa66c8b68b1e7.1686616663.git.kjlx@templeofstupid.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b8ada54fa1 upstream.
The driver overrides the error codes and IRQ0 returned by platform_get_irq()
to -EINVAL, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the error
codes upstream. Since commit ce753ad154 ("platform: finally disallow IRQ0
in platform_get_irq() and its ilk") IRQ0 is no longer returned by those APIs,
so we now can safely ignore it...
Fixes: cbcaac6d7d ("mmc: meson-gx-mmc: Fix platform_get_irq's error checking")
Cc: stable@vger.kernel.org # v5.19+
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230617203622.6812-3-s.shtylyov@omp.ru
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2df53c580 upstream.
The driver overrides the error codes and IRQ0 returned by platform_get_irq()
to -EINVAL, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the error
codes upstream. Since commit ce753ad154 ("platform: finally disallow IRQ0
in platform_get_irq() and its ilk") IRQ0 is no longer returned by those APIs,
so we now can safely ignore it...
Fixes: 2408a08583 ("mmc: sunxi-mmc: Handle return value of platform_get_irq")
Cc: stable@vger.kernel.org # v5.19+
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20230617203622.6812-12-s.shtylyov@omp.ru
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 71150ac125 upstream.
The driver overrides the error codes and IRQ0 returned by platform_get_irq()
to -EINVAL, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the error
codes upstream. Since commit ce753ad154 ("platform: finally disallow IRQ0
in platform_get_irq() and its ilk") IRQ0 is no longer returned by those APIs,
so we now can safely ignore it...
Fixes: 660fc733bd ("mmc: bcm2835: Add new driver for the sdhost controller.")
Cc: stable@vger.kernel.org # v5.19+
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20230617203622.6812-2-s.shtylyov@omp.ru
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e6f9e590b7 upstream.
While SDHCI claims to support 64-bit DMA on MSM8916 it does not seem to
be properly functional. It is not immediately obvious because SDHCI is
usually used with IOMMU bypassed on this SoC, and all physical memory
has 32-bit addresses. But when trying to enable the IOMMU it quickly
fails with an error such as the following:
arm-smmu 1e00000.iommu: Unhandled context fault:
fsr=0x402, iova=0xfffff200, fsynr=0xe0000, cbfrsynra=0x140, cb=3
mmc1: ADMA error: 0x02000000
mmc1: sdhci: ============ SDHCI REGISTER DUMP ===========
mmc1: sdhci: Sys addr: 0x00000000 | Version: 0x00002e02
mmc1: sdhci: Blk size: 0x00000008 | Blk cnt: 0x00000000
mmc1: sdhci: Argument: 0x00000000 | Trn mode: 0x00000013
mmc1: sdhci: Present: 0x03f80206 | Host ctl: 0x00000019
mmc1: sdhci: Power: 0x0000000f | Blk gap: 0x00000000
mmc1: sdhci: Wake-up: 0x00000000 | Clock: 0x00000007
mmc1: sdhci: Timeout: 0x0000000a | Int stat: 0x00000001
mmc1: sdhci: Int enab: 0x03ff900b | Sig enab: 0x03ff100b
mmc1: sdhci: ACmd stat: 0x00000000 | Slot int: 0x00000000
mmc1: sdhci: Caps: 0x322dc8b2 | Caps_1: 0x00008007
mmc1: sdhci: Cmd: 0x0000333a | Max curr: 0x00000000
mmc1: sdhci: Resp[0]: 0x00000920 | Resp[1]: 0x5b590000
mmc1: sdhci: Resp[2]: 0xe6487f80 | Resp[3]: 0x0a404094
mmc1: sdhci: Host ctl2: 0x00000008
mmc1: sdhci: ADMA Err: 0x00000001 | ADMA Ptr: 0x0000000ffffff224
mmc1: sdhci_msm: ----------- VENDOR REGISTER DUMP -----------
mmc1: sdhci_msm: DLL sts: 0x00000000 | DLL cfg: 0x60006400 | DLL cfg2: 0x00000000
mmc1: sdhci_msm: DLL cfg3: 0x00000000 | DLL usr ctl: 0x00000000 | DDR cfg: 0x00000000
mmc1: sdhci_msm: Vndr func: 0x00018a9c | Vndr func2 : 0xf88018a8 Vndr func3: 0x00000000
mmc1: sdhci: ============================================
mmc1: sdhci: fffffffff200: DMA 0x0000ffffffffe100, LEN 0x0008, Attr=0x21
mmc1: sdhci: fffffffff20c: DMA 0x0000000000000000, LEN 0x0000, Attr=0x03
Looking closely it's obvious that only the 32-bit part of the address
(0xfffff200) arrives at the SMMU, the higher 16-bit (0xffff...) get
lost somewhere. This might not be a limitation of the SDHCI itself but
perhaps the bus/interconnect it is connected to, or even the connection
to the SMMU.
Work around this by setting SDHCI_QUIRK2_BROKEN_64_BIT_DMA to avoid
using 64-bit addresses.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230518-msm8916-64bit-v1-1-5694b0f35211@gerhold.net
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f363f5aa8 upstream.
We found a refcount UAF bug as follows:
refcount_t: addition on 0; use-after-free.
WARNING: CPU: 1 PID: 342 at lib/refcount.c:25 refcount_warn_saturate+0xa0/0x148
Workqueue: events cpuset_hotplug_workfn
Call trace:
refcount_warn_saturate+0xa0/0x148
__refcount_add.constprop.0+0x5c/0x80
css_task_iter_advance_css_set+0xd8/0x210
css_task_iter_advance+0xa8/0x120
css_task_iter_next+0x94/0x158
update_tasks_root_domain+0x58/0x98
rebuild_root_domains+0xa0/0x1b0
rebuild_sched_domains_locked+0x144/0x188
cpuset_hotplug_workfn+0x138/0x5a0
process_one_work+0x1e8/0x448
worker_thread+0x228/0x3e0
kthread+0xe0/0xf0
ret_from_fork+0x10/0x20
then a kernel panic will be triggered as below:
Unable to handle kernel paging request at virtual address 00000000c0000010
Call trace:
cgroup_apply_control_disable+0xa4/0x16c
rebind_subsystems+0x224/0x590
cgroup_destroy_root+0x64/0x2e0
css_free_rwork_fn+0x198/0x2a0
process_one_work+0x1d4/0x4bc
worker_thread+0x158/0x410
kthread+0x108/0x13c
ret_from_fork+0x10/0x18
The race that cause this bug can be shown as below:
(hotplug cpu) | (umount cpuset)
mutex_lock(&cpuset_mutex) | mutex_lock(&cgroup_mutex)
cpuset_hotplug_workfn |
rebuild_root_domains | rebind_subsystems
update_tasks_root_domain | spin_lock_irq(&css_set_lock)
css_task_iter_start | list_move_tail(&cset->e_cset_node[ss->id]
while(css_task_iter_next) | &dcgrp->e_csets[ss->id]);
css_task_iter_end | spin_unlock_irq(&css_set_lock)
mutex_unlock(&cpuset_mutex) | mutex_unlock(&cgroup_mutex)
Inside css_task_iter_start/next/end, css_set_lock is hold and then
released, so when iterating task(left side), the css_set may be moved to
another list(right side), then it->cset_head points to the old list head
and it->cset_pos->next points to the head node of new list, which can't
be used as struct css_set.
To fix this issue, switch from all css_sets to only scgrp's css_sets to
patch in-flight iterators to preserve correct iteration, and then
update it->cset_head as well.
Reported-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Link: https://www.spinics.net/lists/cgroups/msg37935.html
Suggested-by: Michal Koutný <mkoutny@suse.com>
Link: https://lore.kernel.org/all/20230526114139.70274-1-xiujianfeng@huaweicloud.com/
Signed-off-by: Xiu Jianfeng <xiujianfeng@huawei.com>
Fixes: 2d8f243a5e ("cgroup: implement cgroup->e_csets[]")
Cc: stable@vger.kernel.org # v3.16+
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 57fc0f1cea upstream.
The MPTCP protocol access the listener subflow in a lockless
manner in a couple of places (poll, diag). That works only if
the msk itself leaves the listener status only after that the
subflow itself has been closed/disconnected. Otherwise we risk
deadlock in diag, as reported by Christoph.
Address the issue ensuring that the first subflow (the listener
one) is always disconnected before updating the msk socket status.
Reported-by: Christoph Paasch <cpaasch@apple.com>
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/407
Fixes: b29fcfb54c ("mptcp: full disconnect implementation")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81c1d02901 upstream.
An orphaned msk releases the used resources via the worker,
when the latter first see the msk in CLOSED status.
If the msk status transitions to TCP_CLOSE in the release callback
invoked by the worker's final release_sock(), such instance of the
workqueue will not take any action.
Additionally the MPTCP code prevents scheduling the worker once the
socket reaches the CLOSE status: such msk resources will be leaked.
The only code path that can trigger the above scenario is the
__mptcp_check_send_data_fin() in fallback mode.
Address the issue removing the special handling of fallback socket
in __mptcp_check_send_data_fin(), consolidating the state machine
for fallback and non fallback socket.
Since non-fallback sockets do not send and do not receive data_fin,
the mptcp code can update the msk internal status to match the next
step in the SM every time data fin (ack) should be generated or
received.
As a consequence we can remove a bunch of checks for fallback from
the fastpath.
Fixes: 6e628cd3a8 ("mptcp: use mptcp release_cb for delayed tasks")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56a666c48b upstream.
At passive MPJ time, if the msk socket lock is held by the user,
the new subflow is appended to the msk->join_list under the msk
data lock.
In mptcp_release_cb()/__mptcp_flush_join_list(), the subflows in
that list are moved from the join_list into the conn_list under the
msk socket lock.
Append and removal could race, possibly corrupting such list.
Address the issue splicing the join list into a temporary one while
still under the msk data lock.
Found by code inspection, the race itself should be almost impossible
to trigger in practice.
Fixes: 3e5014909b ("mptcp: cleanup MPJ subflow list handling")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2b2ae3925 upstream.
Currently the mptcp code has assumes that disconnect() can fail only
at mptcp_sendmsg_fastopen() time - to avoid a deadlock scenario - and
don't even bother returning an error code.
Soon mptcp_disconnect() will handle more error conditions: let's track
them explicitly.
As a bonus, explicitly annotate TCP-level disconnect as not failing:
the mptcp code never blocks for event on the subflows.
Fixes: 7d803344fd ("mptcp: fix deadlock in fastopen error path")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Tested-by: Christoph Paasch <cpaasch@apple.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 78d0d2063b upstream.
We cannot sanely handle partial retries for recvmsg if we have cmsg
attached. If we don't, then we'd just be overwriting the initial cmsg
header on retries. Alternatively we could increment and handle this
appropriately, but it doesn't seem worth the complication.
Move the MSG_WAITALL check into the non-multishot case while at it,
since MSG_WAITALL is explicitly disabled for multishot anyway.
Link: https://lore.kernel.org/io-uring/0b0d4411-c8fd-4272-770b-e030af6919a0@kernel.dk/
Cc: stable@vger.kernel.org # 5.10+
Reported-by: Stefan Metzmacher <metze@samba.org>
Reviewed-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1dc492087 upstream.
If we have cmsg attached AND we transferred partial data at least, clear
msg_controllen on retry so we don't attempt to send that again.
Cc: stable@vger.kernel.org # 5.10+
Fixes: cac9e4418f ("io_uring/net: save msghdr->msg_control for retries")
Reported-by: Stefan Metzmacher <metze@samba.org>
Reviewed-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 067d6ec7ed upstream.
In the case of fast device addition/removal, it's possible that
hv_eject_device_work() can start to run before create_root_hv_pci_bus()
starts to run; as a result, the pci_get_domain_bus_and_slot() in
hv_eject_device_work() can return a 'pdev' of NULL, and
hv_eject_device_work() can remove the 'hpdev', and immediately send a
message PCI_EJECTION_COMPLETE to the host, and the host immediately
unassigns the PCI device from the guest; meanwhile,
create_root_hv_pci_bus() and the PCI device driver can be probing the
dead PCI device and reporting timeout errors.
Fix the issue by adding a per-bus mutex 'state_lock' and grabbing the
mutex before powering on the PCI bus in hv_pci_enter_d0(): when
hv_eject_device_work() starts to run, it's able to find the 'pdev' and call
pci_stop_and_remove_bus_device(pdev): if the PCI device driver has
loaded, the PCI device driver's probe() function is already called in
create_root_hv_pci_bus() -> pci_bus_add_devices(), and now
hv_eject_device_work() -> pci_stop_and_remove_bus_device() is able
to call the PCI device driver's remove() function and remove the device
reliably; if the PCI device driver hasn't loaded yet, the function call
hv_eject_device_work() -> pci_stop_and_remove_bus_device() is able to
remove the PCI device reliably and the PCI device driver's probe()
function won't be called; if the PCI device driver's probe() is already
running (e.g., systemd-udev is loading the PCI device driver), it must
be holding the per-device lock, and after the probe() finishes and releases
the lock, hv_eject_device_work() -> pci_stop_and_remove_bus_device() is
able to proceed to remove the device reliably.
Fixes: 4daace0d8c ("PCI: hv: Add paravirtual PCI front-end for Microsoft Hyper-V VMs")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Acked-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230615044451.5580-6-decui@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2738d5ab79 upstream.
When the host tries to remove a PCI device, the host first sends a
PCI_EJECT message to the guest, and the guest is supposed to gracefully
remove the PCI device and send a PCI_EJECTION_COMPLETE message to the host;
the host then sends a VMBus message CHANNELMSG_RESCIND_CHANNELOFFER to
the guest (when the guest receives this message, the device is already
unassigned from the guest) and the guest can do some final cleanup work;
if the guest fails to respond to the PCI_EJECT message within one minute,
the host sends the VMBus message CHANNELMSG_RESCIND_CHANNELOFFER and
removes the PCI device forcibly.
In the case of fast device addition/removal, it's possible that the PCI
device driver is still configuring MSI-X interrupts when the guest receives
the PCI_EJECT message; the channel callback calls hv_pci_eject_device(),
which sets hpdev->state to hv_pcichild_ejecting, and schedules a work
hv_eject_device_work(); if the PCI device driver is calling
pci_alloc_irq_vectors() -> ... -> hv_compose_msi_msg(), we can break the
while loop in hv_compose_msi_msg() due to the updated hpdev->state, and
leave data->chip_data with its default value of NULL; later, when the PCI
device driver calls request_irq() -> ... -> hv_irq_unmask(), the guest
crashes in hv_arch_irq_unmask() due to data->chip_data being NULL.
Fix the issue by not testing hpdev->state in the while loop: when the
guest receives PCI_EJECT, the device is still assigned to the guest, and
the guest has one minute to finish the device removal gracefully. We don't
really need to (and we should not) test hpdev->state in the loop.
Fixes: de0aa7b2f9 ("PCI: hv: Fix 2 hang issues in hv_compose_msi_msg()")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230615044451.5580-3-decui@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a847234e24 upstream.
This reverts commit d6af2ed29c.
The statement "the hv_pci_bus_exit() call releases structures of all its
child devices" in commit d6af2ed29c is not true: in the path
hv_pci_probe() -> hv_pci_enter_d0() -> hv_pci_bus_exit(hdev, true): the
parameter "keep_devs" is true, so hv_pci_bus_exit() does *not* release the
child "struct hv_pci_dev *hpdev" that is created earlier in
pci_devices_present_work() -> new_pcichild_device().
The commit d6af2ed29c was originally made in July 2020 for RHEL 7.7,
where the old version of hv_pci_bus_exit() was used; when the commit was
rebased and merged into the upstream, people didn't notice that it's
not really necessary. The commit itself doesn't cause any issue, but it
makes hv_pci_probe() more complicated. Revert it to facilitate some
upcoming changes to hv_pci_probe().
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Acked-by: Wei Hu <weh@microsoft.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230615044451.5580-5-decui@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 440b5e3663 upstream.
Since day 1 of the driver, there has been a race between
hv_pci_query_relations() and survey_child_resources(): during fast
device hotplug, hv_pci_query_relations() may error out due to
device-remove and the stack variable 'comp' is no longer valid;
however, pci_devices_present_work() -> survey_child_resources() ->
complete() may be running on another CPU and accessing the no-longer-valid
'comp'. Fix the race by flushing the workqueue before we exit from
hv_pci_query_relations().
Fixes: 4daace0d8c ("PCI: hv: Add paravirtual PCI front-end for Microsoft Hyper-V VMs")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Acked-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230615044451.5580-2-decui@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 320805ab61 upstream.
vmbus_wait_for_unload() may be called in the panic path after other
CPUs are stopped. vmbus_wait_for_unload() currently loops through
online CPUs looking for the UNLOAD response message. But the values of
CONFIG_KEXEC_CORE and crash_kexec_post_notifiers affect the path used
to stop the other CPUs, and in one of the paths the stopped CPUs
are removed from cpu_online_mask. This removal happens in both
x86/x64 and arm64 architectures. In such a case, vmbus_wait_for_unload()
only checks the panic'ing CPU, and misses the UNLOAD response message
except when the panic'ing CPU is CPU 0. vmbus_wait_for_unload()
eventually times out, but only after waiting 100 seconds.
Fix this by looping through *present* CPUs in vmbus_wait_for_unload().
The cpu_present_mask is not modified by stopping the other CPUs in the
panic path, nor should it be.
Also, in a CoCo VM the synic_message_page is not allocated in
hv_synic_alloc(), but is set and cleared in hv_synic_enable_regs()
and hv_synic_disable_regs() such that it is set only when the CPU is
online. If not all present CPUs are online when vmbus_wait_for_unload()
is called, the synic_message_page might be NULL. Add a check for this.
Fixes: cd95aad557 ("Drivers: hv: vmbus: handle various crash scenarios")
Cc: stable@vger.kernel.org
Reported-by: John Starks <jostarks@microsoft.com>
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Link: https://lore.kernel.org/r/1684422832-38476-1-git-send-email-mikelley@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec97e11298 upstream.
Commit 572086325c ("Drivers: hv: vmbus: Cleanup synic memory free path")
says "Any memory allocations that succeeded will be freed when the caller
cleans up by calling hv_synic_free()", but if the get_zeroed_page() in
hv_synic_alloc() fails, currently hv_synic_free() is not really called
in vmbus_bus_init(), consequently there will be a memory leak, e.g.
hv_context.hv_numa_map is not freed in the error path. Fix this by
updating the goto labels.
Cc: stable@kernel.org
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Fixes: 4df4cb9e99 ("x86/hyperv: Initialize clockevents earlier in CPU onlining")
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20230504224155.10484-1-decui@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95a301eefa upstream.
In __vmalloc_area_node() we always warn_alloc() when an allocation
performed by vm_area_alloc_pages() fails unless it was due to a pending
fatal signal.
However, huge page allocations instigated either by vmalloc_huge() or
__vmalloc_node_range() (or a caller that invokes this like kvmalloc() or
kvmalloc_node()) always falls back to order-0 allocations if the huge page
allocation fails.
This renders the warning useless and noisy, especially as all callers
appear to be aware that this may fallback. This has already resulted in
at least one bug report from a user who was confused by this (see link).
Therefore, simply update the code to only output this warning for order-0
pages when no fatal signal is pending.
Link: https://bugzilla.suse.com/show_bug.cgi?id=1211410
Link: https://lkml.kernel.org/r/20230605201107.83298-1-lstoakes@gmail.com
Fixes: 80b1d8fdfa ("mm: vmalloc: correct use of __GFP_NOWARN mask in __vmalloc_area_node()")
Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Baoquan He <bhe@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2230f9e117 upstream.
We run into guest hang in edk2 firmware when KSM is kept as running on
the host. The edk2 firmware is waiting for status 0x80 from QEMU's pflash
device (TYPE_PFLASH_CFI01) during the operation of sector erasing or
buffered write. The status is returned by reading the memory region of
the pflash device and the read request should have been forwarded to QEMU
and emulated by it. Unfortunately, the read request is covered by an
illegal stage2 mapping when the guest hang issue occurs. The read request
is completed with QEMU bypassed and wrong status is fetched. The edk2
firmware runs into an infinite loop with the wrong status.
The illegal stage2 mapping is populated due to same page sharing by KSM
at (C) even the associated memory slot has been marked as invalid at (B)
when the memory slot is requested to be deleted. It's notable that the
active and inactive memory slots can't be swapped when we're in the middle
of kvm_mmu_notifier_change_pte() because kvm->mn_active_invalidate_count
is elevated, and kvm_swap_active_memslots() will busy loop until it reaches
to zero again. Besides, the swapping from the active to the inactive memory
slots is also avoided by holding &kvm->srcu in __kvm_handle_hva_range(),
corresponding to synchronize_srcu_expedited() in kvm_swap_active_memslots().
CPU-A CPU-B
----- -----
ioctl(kvm_fd, KVM_SET_USER_MEMORY_REGION)
kvm_vm_ioctl_set_memory_region
kvm_set_memory_region
__kvm_set_memory_region
kvm_set_memslot(kvm, old, NULL, KVM_MR_DELETE)
kvm_invalidate_memslot
kvm_copy_memslot
kvm_replace_memslot
kvm_swap_active_memslots (A)
kvm_arch_flush_shadow_memslot (B)
same page sharing by KSM
kvm_mmu_notifier_invalidate_range_start
:
kvm_mmu_notifier_change_pte
kvm_handle_hva_range
__kvm_handle_hva_range
kvm_set_spte_gfn (C)
:
kvm_mmu_notifier_invalidate_range_end
Fix the issue by skipping the invalid memory slot at (C) to avoid the
illegal stage2 mapping so that the read request for the pflash's status
is forwarded to QEMU and emulated by it. In this way, the correct pflash's
status can be returned from QEMU to break the infinite loop in the edk2
firmware.
We tried a git-bisect and the first problematic commit is cd4c718352 ("
KVM: arm64: Convert to the gfn-based MMU notifier callbacks"). With this,
clean_dcache_guest_page() is called after the memory slots are iterated
in kvm_mmu_notifier_change_pte(). clean_dcache_guest_page() is called
before the iteration on the memory slots before this commit. This change
literally enlarges the racy window between kvm_mmu_notifier_change_pte()
and memory slot removal so that we're able to reproduce the issue in a
practical test case. However, the issue exists since commit d5d8184d35
("KVM: ARM: Memory virtualization setup").
Cc: stable@vger.kernel.org # v3.9+
Fixes: d5d8184d35 ("KVM: ARM: Memory virtualization setup")
Reported-by: Shuai Hu <hshuai@redhat.com>
Reported-by: Zhenyu Zhang <zhenyzha@redhat.com>
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Shaoqin Huang <shahuang@redhat.com>
Message-Id: <20230615054259.14911-1-gshan@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0bb619f922 upstream.
Since commit 955fb8719e ("thermal/intel/intel_soc_dts_iosf: Use Intel
TCC library") intel_soc_dts_iosf is reporting the wrong temperature.
The driver expects tj_max to be in milli-degrees-celcius but after
the switch to the TCC library this is now in degrees celcius so
instead of e.g. 90000 it is set to 90 causing a temperature 45
degrees below tj_max to be reported as -44910 milli-degrees
instead of as 45000 milli-degrees.
Fix this by adding back the lost factor of 1000.
Fixes: 955fb8719e ("thermal/intel/intel_soc_dts_iosf: Use Intel TCC library")
Reported-by: Bernhard Krug <b.krug@elektronenpumpe.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Cc: 6.3+ <stable@vger.kernel.org> # 6.3+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22db06337f upstream.
The addition of might_sleep() to down_timeout() caused the latter to
enable interrupts unconditionally in some cases, which in turn broke
the ACPI S3 wakeup path in acpi_suspend_enter(), where down_timeout()
is called by acpi_disable_all_gpes() via acpi_ut_acquire_mutex().
Namely, if CONFIG_DEBUG_ATOMIC_SLEEP is set, might_sleep() causes
might_resched() to be used and if CONFIG_PREEMPT_VOLUNTARY is set,
this triggers __cond_resched() which may call preempt_schedule_common(),
so __schedule() gets invoked and it ends up with enabled interrupts (in
the prev == next case).
Now, enabling interrupts early in the S3 wakeup path causes the kernel
to crash.
Address this by modifying acpi_suspend_enter() to disable GPEs without
attempting to acquire the sleeping lock which is not needed in that code
path anyway.
Fixes: 99409b935c ("locking/semaphore: Add might_sleep() to down_*() family")
Reported-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: 5.15+ <stable@vger.kernel.org> # 5.15+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 782e53d0c1 upstream.
In a syzbot stress test that deliberately causes file system errors on
nilfs2 with a corrupted disk image, it has been reported that
nilfs_clear_dirty_page() called from nilfs_clear_dirty_pages() can cause a
general protection fault.
In nilfs_clear_dirty_pages(), when looking up dirty pages from the page
cache and calling nilfs_clear_dirty_page() for each dirty page/folio
retrieved, the back reference from the argument page to "mapping" may have
been changed to NULL (and possibly others). It is necessary to check this
after locking the page/folio.
So, fix this issue by not calling nilfs_clear_dirty_page() on a page/folio
after locking it in nilfs_clear_dirty_pages() if the back reference
"mapping" from the page/folio is different from the "mapping" that held
the page/folio just before.
Link: https://lkml.kernel.org/r/20230612021456.3682-1-konishi.ryusuke@gmail.com
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Reported-by: syzbot+53369d11851d8f26735c@syzkaller.appspotmail.com
Closes: https://lkml.kernel.org/r/000000000000da4f6b05eb9bf593@google.com
Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 679bd7ebdd upstream.
As a result of analysis of a syzbot report, it turned out that in three
cases where nilfs2 allocates block device buffers directly via sb_getblk,
concurrent reads to the device can corrupt the allocated buffers.
Nilfs2 uses sb_getblk for segment summary blocks, that make up a log
header, and the super root block, that is the trailer, and when moving and
writing the second super block after fs resize.
In any of these, since the uptodate flag is not set when storing metadata
to be written in the allocated buffers, the stored metadata will be
overwritten if a device read of the same block occurs concurrently before
the write. This causes metadata corruption and misbehavior in the log
write itself, causing warnings in nilfs_btree_assign() as reported.
Fix these issues by setting an uptodate flag on the buffer head on the
first or before modifying each buffer obtained with sb_getblk, and
clearing the flag on failure.
When setting the uptodate flag, the lock_buffer/unlock_buffer pair is used
to perform necessary exclusive control, and the buffer is filled to ensure
that uninitialized bytes are not mixed into the data read from others. As
for buffers for segment summary blocks, they are filled incrementally, so
if the uptodate flag was unset on their allocation, set the flag and zero
fill the buffer once at that point.
Also, regarding the superblock move routine, the starting point of the
memset call to zerofill the block is incorrectly specified, which can
cause a buffer overflow on file systems with block sizes greater than
4KiB. In addition, if the superblock is moved within a large block, it is
necessary to assume the possibility that the data in the superblock will
be destroyed by zero-filling before copying. So fix these potential
issues as well.
Link: https://lkml.kernel.org/r/20230609035732.20426-1-konishi.ryusuke@gmail.com
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Reported-by: syzbot+31837fe952932efc8fb9@syzkaller.appspotmail.com
Closes: https://lkml.kernel.org/r/00000000000030000a05e981f475@google.com
Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54abe19e00 upstream.
When commit 19343b5bdd ("mm/page-writeback: introduce tracepoint for
wait_on_page_writeback()") repurposed the writeback_dirty_page trace event
as a template to create its new wait_on_page_writeback trace event, it
ended up opening a window to NULL pointer dereference crashes due to the
(infrequent) occurrence of a race where an access to a page in the
swap-cache happens concurrently with the moment this page is being written
to disk and the tracepoint is enabled:
BUG: kernel NULL pointer dereference, address: 0000000000000040
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 800000010ec0a067 P4D 800000010ec0a067 PUD 102353067 PMD 0
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 1 PID: 1320 Comm: shmem-worker Kdump: loaded Not tainted 6.4.0-rc5+ #13
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS edk2-20230301gitf80f052277c8-1.fc37 03/01/2023
RIP: 0010:trace_event_raw_event_writeback_folio_template+0x76/0xf0
Code: 4d 85 e4 74 5c 49 8b 3c 24 e8 06 98 ee ff 48 89 c7 e8 9e 8b ee ff ba 20 00 00 00 48 89 ef 48 89 c6 e8 fe d4 1a 00 49 8b 04 24 <48> 8b 40 40 48 89 43 28 49 8b 45 20 48 89 e7 48 89 43 30 e8 a2 4d
RSP: 0000:ffffaad580b6fb60 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff90e38035c01c RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff90e38035c044
RBP: ffff90e38035c024 R08: 0000000000000002 R09: 0000000000000006
R10: ffff90e38035c02e R11: 0000000000000020 R12: ffff90e380bac000
R13: ffffe3a7456d9200 R14: 0000000000001b81 R15: ffffe3a7456d9200
FS: 00007f2e4e8a15c0(0000) GS:ffff90e3fbc80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000040 CR3: 00000001150c6003 CR4: 0000000000170ee0
Call Trace:
<TASK>
? __die+0x20/0x70
? page_fault_oops+0x76/0x170
? kernelmode_fixup_or_oops+0x84/0x110
? exc_page_fault+0x65/0x150
? asm_exc_page_fault+0x22/0x30
? trace_event_raw_event_writeback_folio_template+0x76/0xf0
folio_wait_writeback+0x6b/0x80
shmem_swapin_folio+0x24a/0x500
? filemap_get_entry+0xe3/0x140
shmem_get_folio_gfp+0x36e/0x7c0
? find_busiest_group+0x43/0x1a0
shmem_fault+0x76/0x2a0
? __update_load_avg_cfs_rq+0x281/0x2f0
__do_fault+0x33/0x130
do_read_fault+0x118/0x160
do_pte_missing+0x1ed/0x2a0
__handle_mm_fault+0x566/0x630
handle_mm_fault+0x91/0x210
do_user_addr_fault+0x22c/0x740
exc_page_fault+0x65/0x150
asm_exc_page_fault+0x22/0x30
This problem arises from the fact that the repurposed writeback_dirty_page
trace event code was written assuming that every pointer to mapping
(struct address_space) would come from a file-mapped page-cache object,
thus mapping->host would always be populated, and that was a valid case
before commit 19343b5bdd. The swap-cache address space
(swapper_spaces), however, doesn't populate its ->host (struct inode)
pointer, thus leading to the crashes in the corner-case aforementioned.
commit 19343b5bdd ended up breaking the assignment of __entry->name and
__entry->ino for the wait_on_page_writeback tracepoint -- both dependent
on mapping->host carrying a pointer to a valid inode. The assignment of
__entry->name was fixed by commit 68f23b8906 ("memcg: fix a crash in
wb_workfn when a device disappears"), and this commit fixes the remaining
case, for __entry->ino.
Link: https://lkml.kernel.org/r/20230606233613.1290819-1-aquini@redhat.com
Fixes: 19343b5bdd ("mm/page-writeback: introduce tracepoint for wait_on_page_writeback()")
Signed-off-by: Rafael Aquini <aquini@redhat.com>
Reviewed-by: Yafang Shao <laoar.shao@gmail.com>
Cc: Aristeu Rozanski <aris@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6673851be0 upstream.
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
One of them is the support of a mix of subflows in v4 and v6 by the
in-kernel PM introduced by commit b9d69db87f ("mptcp: let the
in-kernel PM use mixed IPv4 and IPv6 addresses").
It looks like there is no external sign we can use to predict the
expected behaviour. Instead of accepting different behaviours and thus
not really checking for the expected behaviour, we are looking here for
a specific kernel version. That's not ideal but it looks better than
removing the test because it cannot support older kernel versions.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: ad3493746e ("selftests: mptcp: add test-cases for mixed v4/v6 subflows")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 96b84195df upstream.
The alignment was different from the other tests because tabs were used
instead of spaces.
While at it, also use 'echo' instead of 'printf' to print the result to
keep the same style as done in the other sub-tests. And, even if it
should be better with, also remove 'stdbuf' and sed's '--unbuffered'
option because they are not used in the other subtests and they are not
available when using a minimal environment with busybox.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: 178d023208 ("selftests: mptcp: listener test for in-kernel PM")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 632978f0a9 upstream.
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
One of them is the support of sending an MP_PRIO signal for the initial
subflow, introduced by commit c157bbe776 ("mptcp: allow the in kernel
PM to set MPC subflow priority").
It is possible to look for "mptcp_subflow_send_ack" in kallsyms because
it was needed to introduce the mentioned feature. So we can know in
advance if the feature is supported instead of trying and accepting any
results.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: 914f6a59b1 ("selftests: mptcp: add MPC backup tests")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff8897b518 upstream.
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
One of them is the support of the MP_FAIL / infinite mapping introduced
by commit 1e39e5a32a ("mptcp: infinite mapping sending") and the
following ones.
It is possible to look for one of the infinite mapping counters to know
in advance if the this feature is available.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: b6e074e171 ("selftests: mptcp: add infinite map testcase")
Cc: stable@vger.kernel.org
Fixes: 2ba18161d4 ("selftests: mptcp: add MP_FAIL reset testcase")
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f2b492b04a upstream.
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
One of them is the support of the userspace PM introduced by commit
4638de5aef ("mptcp: handle local addrs announced by userspace PMs")
and the following ones.
It is possible to look for the MPTCP pm_type's sysctl knob to know in
advance if the userspace PM is available.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: 5ac1d2d634 ("selftests: mptcp: Add tests for userspace PM type")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9db34c4294 upstream.
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
One of them is the support of the fullmesh flag for the in-kernel PM
introduced by commit 2843ff6f36 ("mptcp: remote addresses fullmesh")
and commit 1a0d6136c5 ("mptcp: local addresses fullmesh").
It looks like there is no easy external sign we can use to predict the
expected behaviour. We could add the flag and then check if it has been
added but for that, and for each fullmesh test, we would need to setup a
new environment, do the checks, clean it and then only start the test
from yet another clean environment. To keep it simple and avoid
introducing new issues, we look for a specific kernel version. That's
not ideal but an acceptable solution for this case.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: 6a0653b96f ("selftests: mptcp: add fullmesh setting tests")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07216a3c5d upstream.
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
Commit bccefb7624 ("selftests: mptcp: simplify pm_nl_change_endpoint")
has simplified the way the backup flag is set on an endpoint. Instead of
doing:
./pm_nl_ctl set 10.0.2.1 flags backup
Now we do:
./pm_nl_ctl set id 1 flags backup
The new way is easier to maintain but it is also incompatible with older
kernels not supporting the implicit endpoints putting in place the
infrastructure to set flags per ID, hence the second Fixes tag.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: bccefb7624 ("selftests: mptcp: simplify pm_nl_change_endpoint")
Cc: stable@vger.kernel.org
Fixes: 4cf86ae84c ("mptcp: strict local address ID selection")
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 36c4127ae8 upstream.
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
One of them is the support of the implicit endpoints introduced by
commit d045b9eb95 ("mptcp: introduce implicit endpoints").
It is possible to look for "mptcp_subflow_send_ack" in kallsyms because
it was needed to introduce the mentioned feature. So we can know in
advance if the feature is supported instead of trying and accepting any
results.
Note that here and in the following commits, we re-do the same check for
each sub-test of the same function for a few reasons. The main one is
not to break the ID assign to each test in order to be able to easily
compare results between different kernel versions. Also, we can still
run a specific test even if it is skipped. Another reason is that it
makes it clear during the review that a specific subtest will be skipped
or not under certain conditions. At the end, it looks OK to call the
exact same helper multiple times: it is not a critical path and it is
the same code that is executed, not really more cases to maintain.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: 69c6ce7b6e ("selftests: mptcp: add implicit endpoint test case")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 425ba80312 upstream.
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
At some points, a new feature caused internal behaviour changes we are
verifying in the selftests, see the Fixes tag below. It was not a UAPI
change but because in these selftests, we check some internal
behaviours, it is normal we have to adapt them from time to time after
having added some features.
It looks like there is no external sign we can use to predict the
expected behaviour. Instead of accepting different behaviours and thus
not really checking for the expected behaviour, we are looking here for
a specific kernel version. That's not ideal but it looks better than
removing the test because it cannot support older kernel versions.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: 6fa0174a7c ("mptcp: more careful RM_ADDR generation")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae947bb2c2 upstream.
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
One of them is the support of MP_FASTCLOSE introduced in commit
f284c0c773 ("mptcp: implement fastclose xmit path").
If the MIB counter is not available, the test cannot be verified and the
behaviour will not be the expected one. So we can skip the test if the
counter is missing.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: 01542c9bf9 ("selftests: mptcp: add fastclose testcase")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d4c81bbb86 upstream.
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
At some points, a new feature caused internal behaviour changes we are
verifying in the selftests, see the Fixes tag below. It was not a uAPI
change but because in these selftests, we check some internal
behaviours, it is normal we have to adapt them from time to time after
having added some features.
It is possible to look for "mptcp_pm_subflow_check_next" in kallsyms
because it was needed to introduce the mentioned feature. So we can know
in advance what the behaviour we are expecting here instead of
supporting the two behaviours.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: 86e39e0448 ("mptcp: keep track of local endpoint still available for each msk")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a0b866a3f upstream.
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
Some tests are using IPTables and/or TC commands to force some
behaviours. If one of these commands fails -- likely because some
features are not available due to missing kernel config -- we should
intercept the error and skip the tests requiring these features.
Note that if we expect to have these features available and if
SELFTESTS_MPTCP_LIB_EXPECT_ALL_FEATURES env var is set to 1, the tests
will be marked as failed instead of skipped.
This patch also replaces the 'exit 1' by 'return 1' not to stop the
selftest in the middle without the conclusion if there is an issue with
NF or TC.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: 8d014eaa92 ("selftests: mptcp: add ADD_ADDR timeout test case")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47867f0a7e upstream.
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
One of them is the MPTCP MIB counters introduced in commit fc518953bc
("mptcp: add and use MIB counter infrastructure") and more later. The
MPTCP Join selftest heavily relies on these counters.
If a counter is not supported by the kernel, it is not displayed when
using 'nstat -z'. We can then detect that and skip the verification. A
new helper (get_counter()) has been added to do the required checks and
return an error if the counter is not available.
Note that if we expect to have these features available and if
SELFTESTS_MPTCP_LIB_EXPECT_ALL_FEATURES env var is set to 1, the tests
will be marked as failed instead of skipped.
This new helper also makes sure we get the exact counter we want to
avoid issues we had in the past, e.g. with MPTcpExtRmAddr and
MPTcpExtRmAddrDrop sharing the same prefix. While at it, we uniform the
way we fetch a MIB counter.
Note for the backports: we rarely change these modified blocks so if
there is are conflicts, it is very likely because a counter is not used
in the older kernels and we don't need that chunk.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: b08fbf2410 ("selftests: add test-cases for MPTCP MP_JOIN")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cdb5052534 upstream.
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
Here are some helpers that will be used to mark subtests as skipped if a
feature is not supported. Marking as a fix for the commit introducing
this selftest to help with the backports.
While at it, also check if kallsyms feature is available as it will also
be used in the following commits to check if MPTCP features are
available before starting a test.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: b08fbf2410 ("selftests: add test-cases for MPTCP MP_JOIN")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1a6a38ab8 upstream.
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
A new function is now available to easily detect if a feature is
missing by looking at the kernel version. That's clearly not ideal and
this kind of check should be avoided as soon as possible. But sometimes,
there are no external sign that a "feature" is available or not:
internal behaviours can change without modifying the uAPI and these
selftests are verifying the internal behaviours. Sometimes, the only
(easy) way to verify if the feature is present is to run the test but
then the validation cannot determine if there is a failure with the
feature or if the feature is missing. Then it looks better to check the
kernel version instead of having tests that can never fail. In any case,
we need a solution not to have a whole selftest being marked as failed
just because one sub-test has failed.
Note that this env var car be set to 1 not to do such check and run the
linked sub-test: SELFTESTS_MPTCP_LIB_NO_KVERSION_CHECK.
This new helper is going to be used in the following commits. In order
to ease the backport of such future patches, it would be good if this
patch is backported up to the introduction of MPTCP selftests, hence the
Fixes tag below: this type of check was supposed to be done from the
beginning.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: 048d19d444 ("mptcp: add basic kselftest for mptcp")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 626cb7a5f6 upstream.
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
One of them is the new listener events linked to the path-manager
introduced by commit f8c9dfbd87 ("mptcp: add pm listener events").
It is possible to look for "mptcp_event_pm_listener" in kallsyms to know
in advance if the kernel supports this feature and skip these sub-tests
if the feature is not supported.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: 6c73008aa3 ("selftests: mptcp: listener test for userspace PM")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f90adb0338 upstream.
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
One of them is the MPTCP Userspace PM introduced by commit 4638de5aef
("mptcp: handle local addrs announced by userspace PMs").
We can skip all these tests if the feature is not supported simply by
looking for the MPTCP pm_type's sysctl knob.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: 259a834fad ("selftests: mptcp: functional tests for the userspace PM type")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b631e3a4e9 upstream.
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
One of them is TCP_INQ cmsg support introduced in commit 2c9e77659a
("mptcp: add TCP_INQ cmsg support").
It is possible to look for "mptcp_ioctl" in kallsyms because it was
needed to introduce the mentioned feature. We can skip these tests and
not set TCPINQ option if the feature is not supported.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: 5cbd886ce2 ("selftests: mptcp: add TCP_INQ support")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c6f7eccc51 upstream.
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
One of them is the getsockopt(SOL_MPTCP) to get info about the MPTCP
connections introduced by commit 55c42fa7fa ("mptcp: add MPTCP_INFO
getsockopt") and the following ones.
It is possible to look for "mptcp_diag_fill_info" in kallsyms because
it is introduced by the mentioned feature. So we can know in advance if
the feature is supported and skip the sub-test if not.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: ce9979129a ("selftests: mptcp: add mptcp getsockopt test cases")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8dee6ca2ac upstream.
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
One of them is the getsockopt(SOL_MPTCP) to get info about the MPTCP
connections introduced by commit 55c42fa7fa ("mptcp: add MPTCP_INFO
getsockopt") and the following ones.
We cannot guess in advance which sizes the kernel will returned: older
kernel can returned smaller sizes, e.g. recently the tcp_info structure
has been modified in commit 71fc704768 ("tcp: add rcv_wnd and
plb_rehash to TCP_INFO") where a new field has been added.
The userspace can also expect a smaller size if it is compiled with old
uAPI kernel headers.
So for these sizes, we can only check if they are above a certain
threshold, 0 for the moment. We can also only compared sizes with the
ones set by the kernel.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: ce9979129a ("selftests: mptcp: add mptcp getsockopt test cases")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f3761b50b8 upstream.
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
One of them is the fullmesh flag that can be given to the MPTCP
in-kernel path-manager and introduced in commit 2843ff6f36 ("mptcp:
remote addresses fullmesh").
If the flag is not visible in the dump after having set it, we don't
check the content. Note that if we expect to have this feature and
SELFTESTS_MPTCP_LIB_EXPECT_ALL_FEATURES env var is set to 1, we always
check the content to avoid regressions.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: 6da1dfdd03 ("selftests: mptcp: add set_flags tests in pm_netlink.sh")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2177d0b08e upstream.
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
One of them is the checks of the default limits returned by the MPTCP
in-kernel path-manager. The default values have been modified by commit
72bcbc46a5 ("mptcp: increase default max additional subflows to 2").
Instead of comparing with hardcoded values, we can get the default one
and compare with them.
Note that if we expect to have the latest version, we continue to check
the hardcoded values to avoid unexpected behaviour changes.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: eedbc68532 ("selftests: add PM netlink functional tests")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc93086aff upstream.
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
One of them is the reporting of the MPTCP sockets being used, introduced
by commit c558246ee7 ("mptcp: add statistics for mptcp socket in use").
Similar to the parent commit, it looks like there is no good pre-check
to do here, i.e. dedicated function available in kallsyms. Instead, we
try to get info and if nothing is returned, the test is marked as
skipped.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: e04a30f788 ("selftest: mptcp: add test for mptcp socket in use")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc97251bf0 upstream.
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
One of them is the listen diag dump support introduced by
commit 4fa39b701c ("mptcp: listen diag dump support").
It looks like there is no good pre-check to do here, i.e. dedicated
function available in kallsyms. Instead, we try to get info if nothing
is returned, the test is marked as skipped.
That's not ideal because something could be wrong with the feature and
instead of reporting an error, the test could be marked as skipped. If
we know in advanced that the feature is supposed to be supported, the
tester can set SELFTESTS_MPTCP_LIB_EXPECT_ALL_FEATURES env var to 1: in
this case the test will report an error instead of marking the test as
skipped if nothing is returned.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: f2ae0fa68e ("selftests/mptcp: add diag listen tests")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ad39a42da upstream.
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
One of them is the full support of disconnections from the userspace
introduced by commit b29fcfb54c ("mptcp: full disconnect
implementation").
It is possible to look for "mptcp_pm_data_reset" in kallsyms because a
preparation patch added it to ease the introduction of the mentioned
feature.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: 05be5e273c ("selftests: mptcp: add disconnect tests")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07bf494019 upstream.
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
One of them is the support of IP(V6)_TRANSPARENT socket option with
MPTCP connections introduced by commit c9406a23c1 ("mptcp: sockopt:
add SOL_IP freebind & transparent options").
It is possible to look for "__ip_sock_set_tos" in kallsyms because
IP(V6)_TRANSPARENT socket option support has been added after TOS
support which came with the required infrastructure in MPTCP sockopt
code. To support TOS, the following function has been exported (T). Not
great but better than checking for a specific kernel version.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: 5fb62e9cd3 ("selftests: mptcp: add tproxy test case")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 673004821a upstream.
Selftests are supposed to run on any kernels, including the old ones not
supporting all MPTCP features.
New functions are now available to easily detect if a certain feature is
missing by looking at kallsyms.
These new helpers are going to be used in the following commits. In
order to ease the backport of such future patches, it would be good if
this patch is backported up to the introduction of MPTCP selftests,
hence the Fixes tag below: this type of check was supposed to be done
from the beginning.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: 048d19d444 ("mptcp: add basic kselftest for mptcp")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0fcd72df88 upstream.
Most of the code had an issue according to ShellCheck.
That's mainly due to the fact it incorrectly believes most of the code
was unreachable because it's invoked by variable name, see how the
"tests" array is used.
Once SC2317 has been ignored, three small warnings were still visible:
- SC2155: Declare and assign separately to avoid masking return values.
- SC2046: Quote this to prevent word splitting: can be ignored because
"ip netns pids" can display more than one pid.
- SC2166: Prefer [ p ] || [ q ] as [ p -o q ] is not well defined.
This probably didn't fix any actual issues but it might help spotting
new interesting warnings reported by ShellCheck as just before,
ShellCheck was reporting issues for most lines making it a bit useless.
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0a85264e48 upstream.
mptcp_connect tool was printing some duplicated entries when showing how
to use it: -j -l -r
While at it, I also:
- moved the very few entries that were not sorted,
- added -R that was missing since
commit 8a4b910d00 ("mptcp: selftests: add rcvbuf set option"),
- removed the -u parameter that has been removed in
commit f730b65c9d ("selftests: mptcp: try to set mptcp ulp mode in different sk states").
No need to backport this, it is just an internal tool used by our
selftests. The help menu is mainly useful for MPTCP kernel devs.
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a stable only patch, so it has no direct upstream
equivalent.
After a stable only patch to explicitly handle the '.got' section to
handle an orphan section warning from the linker, certain configurations
error when linking with ld.lld, which enables relro by default:
ld.lld: error: section: .got is not contiguous with other relro sections
This has come up with other architectures before, such as arm and arm64
in commit 0cda9bc15d ("ARM: 9038/1: Link with '-z norelro'") and
commit 3b92fa7485 ("arm64: link with -z norelro regardless of
CONFIG_RELOCATABLE"). Additionally, '-z norelro' is used unconditionally
for RISC-V upstream after commit 26e7aacb83 ("riscv: Allow to
downgrade paging mode from the command line"), which alluded to this
issue for the same reason. Bring 6.3 in line with mainline and link with
'-z norelro', which resolves the above link failure.
Fixes: e6d1562dd4 ("riscv: vmlinux.lds.S: Explicitly handle '.got' section")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202306192231.DJmWr6BX-lkp@intel.com/
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit afd384f0db upstream.
This reverts commit 07b679f70d.
This change appears to have broken things...
We now see applications hanging during disk accesses.
e.g.
multi-port virtio-blk device running in h/w (FPGA)
Host running a simple 'fio' test.
[global]
thread=1
direct=1
ioengine=libaio
norandommap=1
group_reporting=1
bs=4K
rw=read
iodepth=128
runtime=1
numjobs=4
time_based
[job0]
filename=/dev/vda
[job1]
filename=/dev/vdb
[job2]
filename=/dev/vdc
...
[job15]
filename=/dev/vdp
i.e. 16 disks; 4 queues per disk; simple burst of 4KB reads
This is repeatedly run in a loop.
After a few, normally <10 seconds, fio hangs.
With 64 queues (16 disks), failure occurs within a few seconds; with 8 queues (2 disks) it may take ~hour before hanging.
Last message:
fio-3.19
Starting 8 threads
Jobs: 1 (f=1): [_(7),R(1)][68.3%][eta 03h:11m:06s]
I think this means at the end of the run 1 queue was left incomplete.
'diskstats' (run while fio is hung) shows no outstanding transactions.
e.g.
$ cat /proc/diskstats
...
252 0 vda 1843140071 0 14745120568 712568645 0 0 0 0 0 3117947 712568645 0 0 0 0 0 0
252 16 vdb 1816291511 0 14530332088 704905623 0 0 0 0 0 3117711 704905623 0 0 0 0 0 0
...
Other stats (in the h/w, and added to the virtio-blk driver ([a]virtio_queue_rq(), [b]virtblk_handle_req(), [c]virtblk_request_done()) all agree, and show every request had a completion, and that virtblk_request_done() never gets called.
e.g.
PF= 0 vq=0 1 2 3
[a]request_count - 839416590 813148916 105586179 84988123
[b]completion1_count - 839416590 813148916 105586179 84988123
[c]completion2_count - 0 0 0 0
PF= 1 vq=0 1 2 3
[a]request_count - 823335887 812516140 104582672 75856549
[b]completion1_count - 823335887 812516140 104582672 75856549
[c]completion2_count - 0 0 0 0
i.e. the issue is after the virtio-blk driver.
This change was introduced in kernel 6.3.0.
I am seeing this using 6.3.3.
If I run with an earlier kernel (5.15), it does not occur.
If I make a simple patch to the 6.3.3 virtio-blk driver, to skip the blk_mq_add_to_batch()call, it does not fail.
e.g.
kernel 5.15 - this is OK
virtio_blk.c,virtblk_done() [irq handler]
if (likely(!blk_should_fake_timeout(req->q))) {
blk_mq_complete_request(req);
}
kernel 6.3.3 - this fails
virtio_blk.c,virtblk_handle_req() [irq handler]
if (likely(!blk_should_fake_timeout(req->q))) {
if (!blk_mq_complete_request_remote(req)) {
if (!blk_mq_add_to_batch(req, iob, virtblk_vbr_status(vbr), virtblk_complete_batch)) {
virtblk_request_done(req); //this never gets called... so blk_mq_add_to_batch() must always succeed
}
}
}
If I do, kernel 6.3.3 - this is OK
virtio_blk.c,virtblk_handle_req() [irq handler]
if (likely(!blk_should_fake_timeout(req->q))) {
if (!blk_mq_complete_request_remote(req)) {
virtblk_request_done(req); //force this here...
if (!blk_mq_add_to_batch(req, iob, virtblk_vbr_status(vbr), virtblk_complete_batch)) {
virtblk_request_done(req); //this never gets called... so blk_mq_add_to_batch() must always succeed
}
}
}
Perhaps you might like to fix/test/revert this change...
Martin
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202306090826.C1fZmdMe-lkp@intel.com/
Cc: Suwan Kim <suwan.kim027@gmail.com>
Tested-by: edliaw@google.com
Reported-by: "Roberts, Martin" <martin.roberts@intel.com>
Message-Id: <336455b4f630f329380a8f53ee8cad3868764d5c.1686295549.git.mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13bb06f8dd upstream.
The tick period is aligned very early while the first clock_event_device is
registered. At that point the system runs in periodic mode and switches
later to one-shot mode if possible.
The next wake-up event is programmed based on the aligned value
(tick_next_period) but the delta value, that is used to program the
clock_event_device, is computed based on ktime_get().
With the subtracted offset, the device fires earlier than the exact time
frame. With a large enough offset the system programs the timer for the
next wake-up and the remaining time left is too small to make any boot
progress. The system hangs.
Move the alignment later to the setup of tick_sched timer. At this point
the system switches to oneshot mode and a high resolution clocksource is
available. At this point it is safe to align tick_next_period because
ktime_get() will now return accurate (not jiffies based) time.
[bigeasy: Patch description + testing].
Fixes: e9523a0d81 ("tick/common: Align tick period with the HZ tick.")
Reported-by: Mathias Krause <minipli@grsecurity.net>
Reported-by: "Bhatnagar, Rishabh" <risbhat@amazon.com>
Suggested-by: Mathias Krause <minipli@grsecurity.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Richard W.M. Jones <rjones@redhat.com>
Tested-by: Mathias Krause <minipli@grsecurity.net>
Acked-by: SeongJae Park <sj@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/5a56290d-806e-b9a5-f37c-f21958b5a8c0@grsecurity.net
Link: https://lore.kernel.org/12c6f9a3-d087-b824-0d05-0d18c9bc1bf3@amazon.com
Link: https://lore.kernel.org/r/20230615091830.RxMV2xf_@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5005bcb421 upstream.
This patch validate session id and tree id in compound request.
If first operation in the compound is SMB2 ECHO request, ksmbd bypass
session and tree validation. So work->sess and work->tcon could be NULL.
If secound request in the compound access work->sess or tcon, It cause
NULL pointer dereferecing error.
Cc: stable@vger.kernel.org
Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-21165
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e069265bc upstream.
Writing the TPM_INT_STATUS register in the interrupt handler to clear the
interrupts only has effect if a locality is held. Since this is not
guaranteed at the time the interrupt is fired, claim the locality
explicitly in the handler.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Tested-by: Michael Niewöhner <linux@mniewoehner.de>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d319f34456 upstream.
There are several issues with copy_from_user_nofault():
- access_ok() is designed for user context only and for that reason
it has WARN_ON_IN_IRQ() which triggers when bpf, kprobe, eprobe
and perf on ppc are calling it from irq.
- it's missing nmi_uaccess_okay() which is a nop on all architectures
except x86 where it's required.
The comment in arch/x86/mm/tlb.c explains the details why it's necessary.
Calling copy_from_user_nofault() from bpf, [ke]probe without this check is not safe.
- __copy_from_user_inatomic() under CONFIG_HARDENED_USERCOPY is calling
check_object_size()->__check_object_size()->check_heap_object()->find_vmap_area()->spin_lock()
which is not safe to do from bpf, [ke]probe and perf due to potential deadlock.
Fix all three issues. At the end the copy_from_user_nofault() becomes
equivalent to copy_from_user_nmi() from safety point of view with
a difference in the return value.
Reported-by: Hsin-Wei Hung <hsinweih@uci.edu>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Florian Lehner <dev@der-flo.net>
Tested-by: Hsin-Wei Hung <hsinweih@uci.edu>
Tested-by: Florian Lehner <dev@der-flo.net>
Link: https://lore.kernel.org/r/20230410174345.4376-2-dev@der-flo.net
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: Javier Honduvilla Coto <javierhonduco@gmail.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6aa0365a3c ]
When an ATA port is resumed from sleep, the port is reset and a power
management request issued to libata EH to reset the port and rescanning
the device(s) attached to the port. Device rescanning is done by
scheduling an ata_scsi_dev_rescan() work, which will execute
scsi_rescan_device().
However, scsi_rescan_device() takes the generic device lock, which is
also taken by dpm_resume() when the SCSI device is resumed as well. If
a device rescan execution starts before the completion of the SCSI
device resume, the rcu locking used to refresh the cached VPD pages of
the device, combined with the generic device locking from
scsi_rescan_device() and from dpm_resume() can cause a deadlock.
Avoid this situation by changing struct ata_port scsi_rescan_task to be
a delayed work instead of a simple work_struct. ata_scsi_dev_rescan() is
modified to check if the SCSI device associated with the ATA device that
must be rescanned is not suspended. If the SCSI device is still
suspended, ata_scsi_dev_rescan() returns early and reschedule itself for
execution after an arbitrary delay of 5ms.
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reported-by: Joe Breuer <linux-kernel@jmbreuer.net>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217530
Fixes: a19a93e4c6 ("scsi: core: pm: Rely on the device driver core for async power management")
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Joe Breuer <linux-kernel@jmbreuer.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 81f743a08f ]
[Why & How]
This commit is part of a sequence of changes that replaces the commit
sequence used in the DC with a new one. As a result of this transition,
we moved some specific parts from the commit sequence and brought them
to amdgpu_dm. This commit adds a wrapper inside DM that enable our
drivers to do any necessary preparation or change before we offload the
plane/stream update to DC.
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stable-dep-of: ea2062dd1f ("drm/amd/display: fix the system hang while disable PSR")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f751128982 ]
[Why & How]
The old dc_commit_updates_for_stream lacks manipulation for many corner
cases where the DC feature requires special attention; as a result, it
starts to show its limitation (e.g., the SubVP feature is not supported
by it, among other cases). To modernize and unify our internal API, this
commit replaces the old dc_commit_updates_for_stream with
dc_update_planes_and_stream, which has more features.
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stable-dep-of: ea2062dd1f ("drm/amd/display: fix the system hang while disable PSR")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91f4480c41 ]
The ordering of status checks at the beginning of
cifs_tree_connect is wrong. As a result, a tcon
which is good may stay marked as needing reconnect
infinitely.
Fixes: 2f0e4f0342 ("cifs: check only tcon status on tcon related functions")
Cc: stable@vger.kernel.org # 6.3
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 20cb1c2fb7 upstream.
As noted by Michal, the blkg_iostat_set's in the lockless list hold
reference to blkg's to protect against their removal. Those blkg's
hold reference to blkcg. When a cgroup is being destroyed,
cgroup_rstat_flush() is only called at css_release_work_fn() which
is called when the blkcg reference count reaches 0. This circular
dependency will prevent blkcg and some blkgs from being freed after
they are made offline.
It is less a problem if the cgroup to be destroyed also has other
controllers like memory that will call cgroup_rstat_flush() which will
clean up the reference count. If block is the only controller that uses
rstat, these offline blkcg and blkgs may never be freed leaking more
and more memory over time.
To prevent this potential memory leak:
- flush blkcg per-cpu stats list in __blkg_release(), when no new stat
can be added
- add global blkg_stat_lock for covering concurrent parent blkg stat
update
- don't grab bio->bi_blkg reference when adding the stats into blkcg's
per-cpu stat list since all stats are guaranteed to be consumed before
releasing blkg instance, and grabbing blkg reference for stats was the
most fragile part of original patch
Based on Waiman's patch:
https://lore.kernel.org/linux-block/20221215033132.230023-3-longman@redhat.com/
Fixes: 3b8cc62987 ("blk-cgroup: Optimize blkcg_rstat_flush()")
Cc: stable@vger.kernel.org
Reported-by: Jay Shin <jaeshin@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Waiman Long <longman@redhat.com>
Cc: mkoutny@suse.com
Cc: Yosry Ahmed <yosryahmed@google.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230609234249.1412858-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9127169922 upstream.
In the error exits in target_setup_session(), if a branch is taken to
free_sess: transport_free_session() may call to target_free_cmd_counter()
and then fall through to call target_free_cmd_counter() a second time.
This can, and does, sometimes cause seg faults since the data field in
cmd_cnt->refcnt has been freed in the first call.
Fix this problem by simply returning after the call to
transport_free_session(). The second call is redundant for those cases.
Fixes: 4edba7e4a8 ("scsi: target: Move cmd counter allocation")
Signed-off-by: Bob Pearson <rpearsonhpe@gmail.com>
Link: https://lore.kernel.org/r/20230613144259.12890-1-rpearsonhpe@gmail.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5b2a02bca upstream.
We define sp and ipsw in <asm/asmregs.h> using ".reg", and when using
current binutils (snapshot 2.40.50.20230611) the definitions in
<asm/assembly.h> using "=" conflict with those:
arch/parisc/include/asm/assembly.h: Assembler messages:
arch/parisc/include/asm/assembly.h:93: Error: symbol `sp' is already defined
arch/parisc/include/asm/assembly.h:95: Error: symbol `ipsw' is already defined
Delete the duplicate definitions in <asm/assembly.h>.
Also delete the definition of gp, which isn't used anywhere.
Signed-off-by: Ben Hutchings <benh@debian.org>
Cc: stable@vger.kernel.org # v6.0+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ba00b19067 ]
In the same spirit as commit ca57f02295 ("afs: Fix fileserver probe
RTT handling"), don't rule out using a vlserver just because there
haven't been enough packets yet to calculate a real rtt. Always set the
server's probe rtt from the estimate provided by rxrpc_kernel_get_srtt,
which is capped at 1 second.
This could lead to EDESTADDRREQ errors when accessing a cell for the
first time, even though the vl servers are known and have responded to a
probe.
Fixes: 1d4adfaf65 ("rxrpc: Make rxrpc_kernel_get_srtt() indicate validity")
Signed-off-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: linux-afs@lists.infradead.org
Link: http://lists.infradead.org/pipermail/linux-afs/2023-June/006746.html
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 76a4c8b829 ]
Previously, timestamps were printed using "%lld.%u" which is incorrect
for nanosecond values lower than 100,000,000 as they're fractional
digits, therefore leading zeros are meaningful.
This patch changes the format strings to "%lld.%09u" in order to add
leading zeros to the nanosecond value.
Fixes: 568ebc5985 ("ptp: add the PTP_SYS_OFFSET ioctl to the testptp program")
Fixes: 4ec54f9573 ("ptp: Fix compiler warnings in the testptp utility")
Fixes: 6ab0e475f1 ("Documentation: fix misc. warnings")
Signed-off-by: Alex Maftei <alex.maftei@amd.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20230615083404.57112-1-alex.maftei@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2760904d89 ]
As described in commit 38d11da522 ("dm: don't lock fs when the map is
NULL in process of resume"), a deadlock may be triggered between
do_resume() and do_mount().
This commit preserves the fix from commit 38d11da522 but moves it to
where it also serves to fix a similar deadlock between do_suspend()
and do_mount(). It does so, if the active map is NULL, by clearing
DM_SUSPEND_LOCKFS_FLAG in dm_suspend() which is called by both
do_suspend() and do_resume().
Fixes: 38d11da522 ("dm: don't lock fs when the map is NULL in process of resume")
Signed-off-by: Li Lingfeng <lilingfeng3@huawei.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e84a1e1e68 ]
In systems without MSI-X capabilities, xdp_txq_queues_mode is calculated
in efx_allocate_msix_channels, but when enabling MSI-X fails, it was not
changed to a proper default value. This was leading to the driver
thinking that it has dedicated XDP queues, when it didn't.
Fix it by setting xdp_txq_queues_mode to the correct value if the driver
fallbacks to MSI or legacy IRQ mode. The correct value is
EFX_XDP_TX_QUEUES_BORROWED because there are no XDP dedicated queues.
The issue can be easily visible if the kernel is started with pci=nomsi,
then a call trace is shown. It is not shown only with sfc's modparam
interrupt_mode=2. Call trace example:
WARNING: CPU: 2 PID: 663 at drivers/net/ethernet/sfc/efx_channels.c:828 efx_set_xdp_channels+0x124/0x260 [sfc]
[...skip...]
Call Trace:
<TASK>
efx_set_channels+0x5c/0xc0 [sfc]
efx_probe_nic+0x9b/0x15a [sfc]
efx_probe_all+0x10/0x1a2 [sfc]
efx_pci_probe_main+0x12/0x156 [sfc]
efx_pci_probe_post_io+0x18/0x103 [sfc]
efx_pci_probe.cold+0x154/0x257 [sfc]
local_pci_probe+0x42/0x80
Fixes: 6215b608a8 ("sfc: last resort fallback for lack of xdp tx queues")
Reported-by: Yanghang Liu <yanghliu@redhat.com>
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c0cf3db83 ]
Inside macsec_add_dev() we free percpu macsec->secy.tx_sc.stats and
macsec->stats on some of the memory allocation failure paths. However, the
net_device is already registered to that moment: in macsec_newlink(), just
before calling macsec_add_dev(). This means that during unregister process
its priv_destructor - macsec_free_netdev() - will be called and will free
the stats again.
Remove freeing percpu stats inside macsec_add_dev() because
macsec_free_netdev() will correctly free the already allocated ones. The
pointers to unallocated stats stay NULL, and free_percpu() treats that
correctly.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: 0a28bfd497 ("net/macsec: Add MACsec skb_metadata_dst Tx Data path support")
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ac7a27a8b ]
The DEV_MAC_MAXLEN_CFG register contains a 16-bit value - up to 65535.
Plus 2 * VLAN_HLEN (4), that is up to 65543.
The picos_per_byte variable is the largest when "speed" is lowest -
SPEED_10 = 10. In that case it is (1000000L * 8) / 10 = 800000.
Their product - 52434400000 - exceeds 32 bits, which is a problem,
because apparently, a multiplication between two 32-bit factors is
evaluated as 32-bit before being assigned to a 64-bit variable.
In fact it's a problem for any MTU value larger than 5368.
Cast one of the factors of the multiplication to u64 to force the
multiplication to take place on 64 bits.
Issue found by Coverity.
Fixes: 55a515b1f5 ("net: dsa: felix: drop oversized frames with tc-taprio instead of hanging the port")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230613170907.2413559-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9a82bec02 ]
Mingshuai Ren reports:
When a new chain is added by using tc, one soft lockup alarm will be
generated after delete the prio 0 filter of the chain. To reproduce
the problem, perform the following steps:
(1) tc qdisc add dev eth0 root handle 1: htb default 1
(2) tc chain add dev eth0
(3) tc filter del dev eth0 chain 0 parent 1: prio 0
(4) tc filter add dev eth0 chain 0 parent 1:
Fix the issue by accounting for additional reference to chains that are
explicitly created by RTM_NEWCHAIN message as opposed to implicitly by
RTM_NEWTFILTER message.
Fixes: 726d061286 ("net: sched: prevent insertion of new classifiers during chain flush")
Reported-by: Mingshuai Ren <renmingshuai@huawei.com>
Closes: https://lore.kernel.org/lkml/87legswvi3.fsf@nvidia.com/T/
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Link: https://lore.kernel.org/r/20230612093426.2867183-1-vladbu@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c7e314a63 ]
A recent patch replaced a tasklet execution of cq->comp_handler by a
direct call. While this made sense it let changes to cq->notify state be
unprotected and assumed that the cq completion machinery and the ulp done
callbacks were reentrant. The result is that in some cases completion
events can be lost. This patch moves the cq->comp_handler call inside of
the spinlock in rxe_cq_post which solves both issues. This is compatible
with the matching code in the request notify verb.
Fixes: 78b26a3353 ("RDMA/rxe: Remove tasklet call from rxe_cq.c")
Link: https://lore.kernel.org/r/20230612155032.17036-1-rpearsonhpe@gmail.com
Signed-off-by: Bob Pearson <rpearsonhpe@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c774e6779f ]
umount can race with lease break so need to check if
tcon->ses->server is still valid to send the lease
break response.
Reviewed-by: Bharath SM <bharathsm@microsoft.com>
Reviewed-by: Shyam Prasad N <sprasad@microsoft.com>
Fixes: 59a556aebc ("SMB3: drop reference to cfile before sending oplock break")
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bef68e201e ]
Setting the IPv6 address generation mode of a net device during its
creation never worked, but after commit b0ad3c1790 ("rtnetlink: call
validate_linkmsg in rtnl_create_link") it explicitly fails [1]. The
failure is caused by the fact that validate_linkmsg() is called before
the net device is registered, when it still does not have an 'inet6_dev'.
Likewise, raising the net device before setting the address generation
mode is meaningless, because by the time the mode is set, the address
has already been generated.
Therefore, fix the test to first create the net device, then set its
IPv6 address generation mode and finally bring it up.
[1]
# ip link add name mydev addrgenmode eui64 type dummy
RTNETLINK answers: Address family not supported by protocol
Fixes: ba95e79309 ("selftests: forwarding: hw_stats_l3: Add a new test")
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/f3b05d85b2bc0c3d6168fe8f7207c6c8365703db.1686580046.git.petrm@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84ad0af0bc ]
mini_Qdisc_pair::p_miniq is a double pointer to mini_Qdisc, initialized
in ingress_init() to point to net_device::miniq_ingress. ingress Qdiscs
access this per-net_device pointer in mini_qdisc_pair_swap(). Similar
for clsact Qdiscs and miniq_egress.
Unfortunately, after introducing RTNL-unlocked RTM_{NEW,DEL,GET}TFILTER
requests (thanks Hillf Danton for the hint), when replacing ingress or
clsact Qdiscs, for example, the old Qdisc ("@old") could access the same
miniq_{in,e}gress pointer(s) concurrently with the new Qdisc ("@new"),
causing race conditions [1] including a use-after-free bug in
mini_qdisc_pair_swap() reported by syzbot:
BUG: KASAN: slab-use-after-free in mini_qdisc_pair_swap+0x1c2/0x1f0 net/sched/sch_generic.c:1573
Write of size 8 at addr ffff888045b31308 by task syz-executor690/14901
...
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xd9/0x150 lib/dump_stack.c:106
print_address_description.constprop.0+0x2c/0x3c0 mm/kasan/report.c:319
print_report mm/kasan/report.c:430 [inline]
kasan_report+0x11c/0x130 mm/kasan/report.c:536
mini_qdisc_pair_swap+0x1c2/0x1f0 net/sched/sch_generic.c:1573
tcf_chain_head_change_item net/sched/cls_api.c:495 [inline]
tcf_chain0_head_change.isra.0+0xb9/0x120 net/sched/cls_api.c:509
tcf_chain_tp_insert net/sched/cls_api.c:1826 [inline]
tcf_chain_tp_insert_unique net/sched/cls_api.c:1875 [inline]
tc_new_tfilter+0x1de6/0x2290 net/sched/cls_api.c:2266
...
@old and @new should not affect each other. In other words, @old should
never modify miniq_{in,e}gress after @new, and @new should not update
@old's RCU state.
Fixing without changing sch_api.c turned out to be difficult (please
refer to Closes: for discussions). Instead, make sure @new's first call
always happen after @old's last call (in {ingress,clsact}_destroy()) has
finished:
In qdisc_graft(), return -EBUSY if @old has any ongoing filter requests,
and call qdisc_destroy() for @old before grafting @new.
Introduce qdisc_refcount_dec_if_one() as the counterpart of
qdisc_refcount_inc_nz() used for filter requests. Introduce a
non-static version of qdisc_destroy() that does a TCQ_F_BUILTIN check,
just like qdisc_put() etc.
Depends on patch "net/sched: Refactor qdisc_graft() for ingress and
clsact Qdiscs".
[1] To illustrate, the syzkaller reproducer adds ingress Qdiscs under
TC_H_ROOT (no longer possible after commit c7cfbd1150 ("net/sched:
sch_ingress: Only create under TC_H_INGRESS")) on eth0 that has 8
transmission queues:
Thread 1 creates ingress Qdisc A (containing mini Qdisc a1 and a2),
then adds a flower filter X to A.
Thread 2 creates another ingress Qdisc B (containing mini Qdisc b1 and
b2) to replace A, then adds a flower filter Y to B.
Thread 1 A's refcnt Thread 2
RTM_NEWQDISC (A, RTNL-locked)
qdisc_create(A) 1
qdisc_graft(A) 9
RTM_NEWTFILTER (X, RTNL-unlocked)
__tcf_qdisc_find(A) 10
tcf_chain0_head_change(A)
mini_qdisc_pair_swap(A) (1st)
|
| RTM_NEWQDISC (B, RTNL-locked)
RCU sync 2 qdisc_graft(B)
| 1 notify_and_destroy(A)
|
tcf_block_release(A) 0 RTM_NEWTFILTER (Y, RTNL-unlocked)
qdisc_destroy(A) tcf_chain0_head_change(B)
tcf_chain0_head_change_cb_del(A) mini_qdisc_pair_swap(B) (2nd)
mini_qdisc_pair_swap(A) (3rd) |
... ...
Here, B calls mini_qdisc_pair_swap(), pointing eth0->miniq_ingress to
its mini Qdisc, b1. Then, A calls mini_qdisc_pair_swap() again during
ingress_destroy(), setting eth0->miniq_ingress to NULL, so ingress
packets on eth0 will not find filter Y in sch_handle_ingress().
This is just one of the possible consequences of concurrently accessing
miniq_{in,e}gress pointers.
Fixes: 7a096d579e ("net: sched: ingress: set 'unlocked' flag for Qdisc ops")
Fixes: 87f373921c ("net: sched: ingress: set 'unlocked' flag for clsact Qdisc ops")
Reported-by: syzbot+b53a9c0d1ea4ad62da8b@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/r/0000000000006cf87705f79acf1a@google.com/
Cc: Hillf Danton <hdanton@sina.com>
Cc: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Peilin Ye <peilin.ye@bytedance.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41f2c7c342 ]
Currently UNREPLIED and UNASSURED connections are added to the nf flow
table. This causes the following connection packets to be processed
by the flow table which then skips conntrack_in(), and thus such the
connections will remain UNREPLIED and UNASSURED even if reply traffic
is then seen. Even still, the unoffloaded reply packets are the ones
triggering hardware update from new to established state, and if
there aren't any to triger an update and/or previous update was
missed, hardware can get out of sync with sw and still mark
packets as new.
Fix the above by:
1) Not skipping conntrack_in() for UNASSURED packets, but still
refresh for hardware, as before the cited patch.
2) Try and force a refresh by reply-direction packets that update
the hardware rules from new to established state.
3) Remove any bidirectional flows that didn't failed to update in
hardware for re-insertion as bidrectional once any new packet
arrives.
Fixes: 6a9bad0069 ("net/sched: act_ct: offload UDP NEW connections")
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/1686313379-117663-1-git-send-email-paulb@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b39d8c41c7 ]
Setting very small value of db like 10ms introduces rounding errors when
converting to/from jiffies on some kernel configs. For example, on 250hz
the actual value will be set to 12ms which causes the test to fail:
# $ sudo ./tdc.py -d eth2 -e 3410
# -- ns/SubPlugin.__init__
# Test 3410: Create SFB with db setting
#
# All test results:
#
# 1..1
# not ok 1 3410 - Create SFB with db setting
# Could not match regex pattern. Verify command output:
# qdisc sfb 1: root refcnt 2 rehash 600s db 12ms limit 1000p max 25p target 20p increment 0.000503548 decrement 4.57771e-05 penalty_rate 10pps penalty_burst 20p
Set the value to 100ms instead which currently seem to work on 100hz,
250hz, 300hz and 1000hz kernel configs.
Fixes: 6ad92dc56f ("selftests/tc-testing: add selftests for sfb qdisc")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Pedro Tammela <pctammela@mojatatu.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20a2ce87fb ]
Add checking for NULL before calling nouveau_connector_detect_depth() in
nouveau_connector_get_modes() function because nv_connector->native_mode
could be dereferenced there since connector pointer passed to
nouveau_connector_detect_depth() and the same value of
nv_connector->native_mode is used there.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: d4c2c99bdc ("drm/nouveau/dp: remove broken display depth function, use the improved one")
Signed-off-by: Natalia Petrova <n.petrova@fintech.ru>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230512111526.82408-1-n.petrova@fintech.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11d24327c2 ]
The call site of nouveau_dsm_pci_probe() uses single set of output
variables for all invocations. So, we must not write anything to them
unless it's an NVIDIA device. Otherwise, if we are called with another
device after the NVIDIA device, we'll clober the result of the NVIDIA
device.
For example, if the other device doesn't have _PR3 resources, the
detection later would miss the presence of power resource support, and
the rest of the code will keep using Optimus DSM, breaking power
management for that machine.
Also, because we're detecting NVIDIA's DSM, it doesn't make sense to run
this detection on a non-NVIDIA device anyway. Thus, check at the
beginning of the detection code if this is an NVIDIA card, and just
return if it isn't.
This, together with commit d22915d22d ("drm/nouveau/devinit/tu102-:
wait for GFW_BOOT_PROGRESS == COMPLETED") developed independently and
landed earlier, fixes runtime power management of the NVIDIA card in
Lenovo Legion 5-15ARH05. Without this patch, the GPU resumption code
will "timeout", sometimes hanging userspace.
As a bonus, we'll also stop preventing _PR3 usage from the bridge for
unrelated devices, which is always nice, I guess.
Fixes: ccfc2d5cdb ("drm/nouveau: Use generic helper to check _PR3 presence")
Signed-off-by: Ratchanan Srirattanamet <peathot@hotmail.com>
Closes: https://gitlab.freedesktop.org/drm/nouveau/-/issues/79
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/DM6PR19MB2780805D4BE1E3F9B3AC96D0BC409@DM6PR19MB2780.namprd19.prod.outlook.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 923454c036 ]
Q-USGMII is a derivative of USGMII, that uses a specific formatting for
the control word. The layout is close to the USXGMII control word, but
doesn't support speeds over 1Gbps. Use a dedicated decoding logic for
the USGMII control word, re-using USXGMII definitions but only considering
10/100/1000Mbps speeds
Fixes: 5e61fe157a ("net: phy: Introduce QUSGMII PHY mode")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b9dc1046ed ]
Q-USGMII is the quad port version of USGMII, and supports a max speed of
1Gbps on each line. Make so that phylink_interface_max_speed() reports
this information correctly.
Fixes: ae0e4bb2a0 ("net: phylink: Adjust link settings based on rate matching")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c080fe262f ]
Guarantee that when probe() is run again, PTM and PCI busmaster will be
in the same state as it was if the driver was never loaded.
Avoid an i225/i226 hardware issue that PTM requests can be made even
though PCI bus mastering is not enabled. These unexpected PTM requests
can crash some systems.
So, "force" disable PTM and busmastering before removing the driver,
so they can be re-enabled in the right order during probe(). This is
more like a workaround and should be applicable for i225 and i226, in
any platform.
Fixes: 1b5d73fb86 ("igc: Enable PCIe PTM")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75e6def3b2 ]
The sctp_sf_eat_auth() function is supposed to enum sctp_disposition
values and returning a kernel error code will cause issues in the
caller. Change -ENOMEM to SCTP_DISPOSITION_NOMEM.
Fixes: 65b07e5d0d ("[SCTP]: API updates to suport SCTP-AUTH extensions.")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Acked-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce57adc222 ]
The commit 59a0b022aa ("ipvlan: Make skb->skb_iif track skb->dev for l3s
mode") fixed ipvlan bonded dev checking by updating skb skb_iif. This fix
works for IPv4, as in raw_v4_input() the dif is from inet_iif(skb), which
is skb->skb_iif when there is no route.
But for IPv6, the fix is not enough, because in ipv6_raw_deliver() ->
raw_v6_match(), the dif is inet6_iif(skb), which is returns IP6CB(skb)->iif
instead of skb->skb_iif if it's not a l3_slave. To fix the IPv6 part
issue. Let's set IP6CB(skb)->iif to correct ifindex.
BTW, ipvlan handles NS/NA specifically. Since it works fine, I will not
reset IP6CB(skb)->iif when addr->atype is IPVL_ICMPV6.
Fixes: c675e06a98 ("ipvlan: decouple l3s mode dependencies from other modes")
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2196710
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 52f79609c0 ]
When compiling YNL generated code compiler complains about
array-initializer-out-of-bounds. Turns out the MAX value
for STATS_GRP uses the value for STATS.
This may lead to random corruptions in user space (kernel
itself doesn't use this value as it never parses stats).
Fixes: f09ea6fb12 ("ethtool: add a new command for reading standard stats")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 699826f4e3 ]
The ib_isert module is releasing the isert connection both in
isert_wait_conn() handler as well as isert_free_conn() handler.
In isert_wait_conn() handler, it is expected to wait for iSCSI
session logout operation to complete. It should free the isert
connection only in isert_free_conn() handler.
When a bunch of iSER target is cleared, this issue can lead to
use-after-free memory issue as isert conn is twice released
Fixes: b02efbfc9a ("iser-target: Fix implicit termination of connections")
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Saravanan Vajravel <saravanan.vajravel@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://lore.kernel.org/r/20230606102531.162967-4-saravanan.vajravel@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 617f5db1a6 ]
The cited commit aimed to ensure that Virtual Functions (VFs) assign a
queue affinity to a Queue Pair (QP) to distribute traffic when
the LAG master creates a hardware LAG. If the affinity was set while
the hardware was not in LAG, the firmware would ignore the affinity value.
However, this commit unintentionally assigned an affinity to QPs on the LAG
master's VPORT even if the RDMA device was not marked as LAG-enabled.
In most cases, this was not an issue because when the hardware entered
hardware LAG configuration, the RDMA device of the LAG master would be
destroyed and a new one would be created, marked as LAG-enabled.
The problem arises when a user configures Equal-Cost Multipath (ECMP).
In ECMP mode, traffic can be directed to different physical ports based on
the queue affinity, which is intended for use by VPORTS other than the
E-Switch manager. ECMP mode is supported only if both E-Switch managers are
in switchdev mode and the appropriate route is configured via IP. In this
configuration, the RDMA device is not destroyed, and we retain the RDMA
device that is not marked as LAG-enabled.
To ensure correct behavior, Send Queues (SQs) opened by the E-Switch
manager through verbs should be assigned strict affinity. This means they
will only be able to communicate through the native physical port
associated with the E-Switch manager. This will prevent the firmware from
assigning affinity and will not allow the SQs to be remapped in case of
failover.
Fixes: 802dcc7fc5 ("RDMA/mlx5: Support TX port affinity for VF drivers in LAG mode")
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://lore.kernel.org/r/425b05f4da840bc684b0f7e8ebf61aeb5cef09b0.1685960567.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62fab312fa ]
Fix ib_uverbs_event_read() to consider event queue closing also upon
non-blocking mode.
Once the queue is closed (e.g. hot-plug flow) all the existing events
are cleaned-up as part of ib_uverbs_free_event_queue().
An application that uses the non-blocking FD mode should get -EIO in
that case to let it knows that the device was removed already.
Otherwise, it can loose the indication that the device was removed and
won't recover.
As part of that, refactor the code to have a single flow with regards to
'is_closed' for both blocking and non-blocking modes.
Fixes: 14e23bd6d2 ("RDMA/core: Fix locking in ib_uverbs_event_read")
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Link: https://lore.kernel.org/r/97b00116a1e1e13f8dc4ec38a5ea81cf8c030210.1685960567.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1f4a52ac1 ]
A misbehaved user can create a steering anchor that points to a kernel
flow table and then destroy the anchor without freeing the associated
STC. This creates a problem as the kernel can't destroy the flow
table since there is still a reference to it. As a result, this can
exhaust all available flow table resources, preventing other users from
using the RDMA device.
To prevent this problem, a solution is implemented where a special flow
table with two steering rules is created when a user creates a steering
anchor for the first time. The rules include one that drops all traffic
and another that points to the kernel flow table. If the steering anchor
is destroyed, only the rule pointing to the kernel's flow table is removed.
Any traffic reaching the special flow table after that is dropped.
Since the special flow table is not destroyed when the steering anchor is
destroyed, any issues are prevented from occurring. The remaining resources
are only destroyed when the RDMA device is destroyed, which happens after
all DEVX objects are freed, including the STCs, thus mitigating the issue.
Fixes: 0c6ab0ca9a ("RDMA/mlx5: Expose steering anchor to userspace")
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Link: https://lore.kernel.org/r/b4a88a871d651fa4e8f98d552553c1cfe9ba2cd6.1685960567.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee4d269ecc ]
Delay drop data is initiated for PFs that have the capability of
rq_delay_drop and are in roce profile.
However, PFs with RAW ethernet profile do not initiate delay drop data
on function load, causing kernel panic if delay drop struct members are
accessed later on in case a dropless RQ is created.
Thus, stage the delay drop initialization as part of RAW ethernet
PF loading process.
Fixes: b5ca15ad7e ("IB/mlx5: Add proper representors support")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Link: https://lore.kernel.org/r/2e9d386785043d48c38711826eb910315c1de141.1685960567.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87e12a17ee ]
Fix LBK link credits on CN10K to be same as CN9K i.e
16 * MAX_LBK_DATA_RATE instead of current scheme of
calculation based on LBK buf length / FIFO size.
Fixes: 6e54e1c539 ("octeontx2-af: cn10K: Add MTU configuration")
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e635f9d86 ]
txschq_alloc response have two different arrays to store continuous
and non-continuous schedulers of each level. Requested count should
be checked for each array separately.
Fixes: 5d9b976d44 ("octeontx2-af: Support fixed transmit scheduler topology")
Signed-off-by: Satha Rao <skoteshwar@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04c55383fa ]
In the event of a failure in tcf_change_indev(), u32_set_parms() will
immediately return without decrementing the recently incremented
reference counter. If this happens enough times, the counter will
rollover and the reference freed, leading to a double free which can be
used to do 'bad things'.
In order to prevent this, move the point of possible failure above the
point where the reference counter is incremented. Also save any
meaningful return values to be applied to the return data at the
appropriate point in time.
This issue was caught with KASAN.
Fixes: 705c709126 ("net: sched: cls_u32: no need to call tcf_exts_change for newly allocated struct")
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be3618d965 ]
As shown in [1], out-of-bounds access occurs in two cases:
1)when the qdisc of the taprio type is used to replace the previously
configured taprio, count and offset in tc_to_txq can be set to 0. In this
case, the value of *txq in taprio_next_tc_txq() will increases
continuously. When the number of accessed queues exceeds the number of
queues on the device, out-of-bounds access occurs.
2)When packets are dequeued, taprio can be deleted. In this case, the tc
rule of dev is cleared. The count and offset values are also set to 0. In
this case, out-of-bounds access is also caused.
Now the restriction on the queue number is added.
[1] https://groups.google.com/g/syzkaller-bugs/c/_lYOKgkBVMg
Fixes: 2f530df76c ("net/sched: taprio: give higher priority to higher TCs in software dequeue mode")
Reported-by: syzbot+04afcb3d2c840447559a@syzkaller.appspotmail.com
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Tested-by: Pedro Tammela <pctammela@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0e489372a ]
CN10KB silicon introduced a new exact match feature,
which is used for DMAC filtering. The state of installed
DMAC filters in this exact match table is getting corrupted
when promiscuous mode is toggled. Fix this by not touching
Exact match related config when promiscuous mode is toggled.
Fixes: 2dba9459d2 ("octeontx2-af: Wrapper functions for MAC addr add/del/update/reset")
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ad4982c52 ]
The timestamp descriptors were intended to act cyclically. Descriptors
from index 0 through gq->ring_size - 1 contain actual information, and
the last index (gq->ring_size) should have LINKFIX to indicate
the first index 0 descriptor. However, the LINKFIX value is missing,
causing the timestamp feature to stop after all descriptors are used.
To resolve this issue, set the LINKFIX to the timestamp descritors.
Reported-by: Phong Hoang <phong.hoang.wz@renesas.com>
Fixes: 33f5d733b5 ("net: renesas: rswitch: Improve TX timestamp accuracy")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c02568fd1 ]
Instead of relying on skb->transport_header being set correctly, opt
instead to parse the L3 header length out of the L3 headers for both
IPv4/IPv6 when the Extended Layer Op for tcp/udp is used. This fixes a
bug if GRO is disabled, when GRO is disabled skb->transport_header is
set by __netif_receive_skb_core() to point to the L3 header, it's later
fixed by the upper protocol layers, but act_pedit will receive the SKB
before the fixups are completed. The existing behavior causes the
following to edit the L3 header if GRO is disabled instead of the UDP
header:
tc filter add dev eth0 ingress protocol ip flower ip_proto udp \
dst_ip 192.168.1.3 action pedit ex munge udp set dport 18053
Also re-introduce a rate-limited warning if we were unable to extract
the header offset when using the 'ex' interface.
Fixes: 71d0ed7079 ("net/act_pedit: Support using offset relative to
the conventional network headers")
Signed-off-by: Max Tottenham <mtottenh@akamai.com>
Reviewed-by: Josh Hunt <johunt@akamai.com>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202305261541.N165u9TZ-lkp@intel.com/
Reviewed-by: Pedro Tammela <pctammela@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6292d7436c ]
82580/i354/i350 features circle-counter-like timestamp registers
that are different with newer i210. The EXTTS capture value in
AUXTSMPx should be converted from raw circle counter value to
timestamp value in resolution of 1 nanosec by the driver.
This issue can be reproduced on i350 nics, connecting an 1PPS
signal to a SDP pin, and run 'ts2phc' command to read external
1PPS timestamp value. On i210 this works fine, but on i350 the
extts is not correctly converted.
The i350/i354/82580's SYSTIM and other timestamp registers are
40bit counters, presenting time range of 2^40 ns, that means these
registers overflows every about 1099s. This causes all these regs
can't be used directly in contrast to the newer i210/i211s.
The igb driver needs to convert these raw register values to
valid time stamp format by using kernel timecounter apis for i350s
families. Here the igb_extts() just forgot to do the convert.
Fixes: 38970eac41 ("igb: support EXTTS on 82580/i354/i350")
Signed-off-by: Yuezhen Luan <eggcar.luan@gmail.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230607164116.3768175-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91ffd1bae1 ]
Ping sockets can't send packets when they're bound to a VRF master
device and the output interface is set to a slave device.
For example, when net.ipv4.ping_group_range is properly set, so that
ping6 can use ping sockets, the following kind of commands fails:
$ ip vrf exec red ping6 fe80::854:e7ff:fe88:4bf1%eth1
What happens is that sk->sk_bound_dev_if is set to the VRF master
device, but 'oif' is set to the real output device. Since both are set
but different, ping_v6_sendmsg() sees their value as inconsistent and
fails.
Fix this by allowing 'oif' to be a slave device of ->sk_bound_dev_if.
This fixes the following kselftest failure:
$ ./fcnal-test.sh -t ipv6_ping
[...]
TEST: ping out, vrf device+address bind - ns-B IPv6 LLA [FAIL]
Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Closes: https://lore.kernel.org/netdev/b6191f90-ffca-dbca-7d06-88a9788def9c@alu.unizg.hr/
Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Fixes: 5e45789698 ("net: ipv6: Fix ping to link-local addresses.")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/6c8b53108816a8d0d5705ae37bdc5a8322b5e3d9.1686153846.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21225873be ]
For ENETC hardware, the TCs are numbered from 0 to N-1, where N
is the number of TCs. Numerically higher TC has higher priority.
It's obvious that the highest priority TC index should be N-1 and
the 2nd highest priority TC index should be N-2.
However, the previous logic uses netdev_get_prio_tc_map() to get
the indexes of highest priority and 2nd highest priority TCs, it
does not make sense and is incorrect to give a "tc" argument to
netdev_get_prio_tc_map(). So the driver may get the wrong indexes
of the two highest priotiry TCs which would lead to failed to set
the CBS for the two highest priotiry TCs.
e.g.
$ tc qdisc add dev eno0 parent root handle 100: mqprio num_tc 6 \
map 0 0 1 1 2 3 4 5 queues 1@0 1@1 1@2 1@3 2@4 2@6 hw 1
$ tc qdisc replace dev eno0 parent 100:6 cbs idleslope 100000 \
sendslope -900000 hicredit 12 locredit -113 offload 1
$ Error: Specified device failed to setup cbs hardware offload.
^^^^^
In this example, the previous logic deems the indexes of the two
highest priotiry TCs should be 3 and 2. Actually, the indexes are
5 and 4, because the number of TCs is 6. So it would be failed to
configure the CBS for the two highest priority TCs.
Fixes: c431047c4e ("enetc: add support Credit Based Shaper(CBS) for hardware offload")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1240eb93f0 ]
In case of error when adding a new rule that refers to an anonymous set,
deactivate expressions via NFT_TRANS_PREPARE state, not NFT_TRANS_RELEASE.
Thus, the lookup expression marks anonymous sets as inactive in the next
generation to ensure it is not reachable in this transaction anymore and
decrement the set refcount as introduced by c1592a8994 ("netfilter:
nf_tables: deactivate anonymous set from preparation phase"). The abort
step takes care of undoing the anonymous set.
This is also consistent with rule deletion, where NFT_TRANS_PREPARE is
used. Note that this error path is exercised in the preparation step of
the commit protocol. This patch replaces nf_tables_rule_release() by the
deactivate and destroy calls, this time with NFT_TRANS_PREPARE.
Due to this incorrect error handling, it is possible to access a
dangling pointer to the anonymous set that remains in the transaction
list.
[1009.379054] BUG: KASAN: use-after-free in nft_set_lookup_global+0x147/0x1a0 [nf_tables]
[1009.379106] Read of size 8 at addr ffff88816c4c8020 by task nft-rule-add/137110
[1009.379116] CPU: 7 PID: 137110 Comm: nft-rule-add Not tainted 6.4.0-rc4+ #256
[1009.379128] Call Trace:
[1009.379132] <TASK>
[1009.379135] dump_stack_lvl+0x33/0x50
[1009.379146] ? nft_set_lookup_global+0x147/0x1a0 [nf_tables]
[1009.379191] print_address_description.constprop.0+0x27/0x300
[1009.379201] kasan_report+0x107/0x120
[1009.379210] ? nft_set_lookup_global+0x147/0x1a0 [nf_tables]
[1009.379255] nft_set_lookup_global+0x147/0x1a0 [nf_tables]
[1009.379302] nft_lookup_init+0xa5/0x270 [nf_tables]
[1009.379350] nf_tables_newrule+0x698/0xe50 [nf_tables]
[1009.379397] ? nf_tables_rule_release+0xe0/0xe0 [nf_tables]
[1009.379441] ? kasan_unpoison+0x23/0x50
[1009.379450] nfnetlink_rcv_batch+0x97c/0xd90 [nfnetlink]
[1009.379470] ? nfnetlink_rcv_msg+0x480/0x480 [nfnetlink]
[1009.379485] ? __alloc_skb+0xb8/0x1e0
[1009.379493] ? __alloc_skb+0xb8/0x1e0
[1009.379502] ? entry_SYSCALL_64_after_hwframe+0x46/0xb0
[1009.379509] ? unwind_get_return_address+0x2a/0x40
[1009.379517] ? write_profile+0xc0/0xc0
[1009.379524] ? avc_lookup+0x8f/0xc0
[1009.379532] ? __rcu_read_unlock+0x43/0x60
Fixes: 958bee14d0 ("netfilter: nf_tables: use new transaction infrastructure to handle sets")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05a1308a2e ]
If pf is NULL in ice_gnss_read() then it will be dereferenced
in the error path by a call to dev_dbg(ice_pf_to_dev(pf), ...).
Avoid this by simply returning in this case.
If logging is desired an alternate approach might be to
use pr_err() before returning.
Flagged by Smatch as:
.../ice_gnss.c:196 ice_gnss_read() error: we previously assumed 'pf' could be null (see line 131)
Fixes: 43113ff734 ("ice: add TTY for GNSS module for E810T device")
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f8fdcb0a7 ]
The ice-gnss-<dev_name> kernel thread, which reads data from the u-blox
GNSS module, keep a CPU core almost 100% busy. The main reason is that
it busy-waits for data to become available.
A simple improvement would be to replace the "mdelay(10);" in
ice_gnss_read() with sleeping. A better fix is to not do any waiting
directly in the function and just requeue this delayed work as needed.
The advantage is that canceling the work from ice_gnss_exit() becomes
immediate, rather than taking up to ~2.5 seconds (ICE_MAX_UBX_READ_TRIES
* 10 ms).
This lowers the CPU usage of the ice-gnss-<dev_name> thread on my system
from ~90 % to ~8 %.
I am not sure if the larger 0.1 s pause after inserting data into the
gnss subsystem is really necessary, but I'm keeping that as it was.
Of course, ideally the driver would not have to poll at all, but I don't
know if the E810 can watch for GNSS data availability over the i2c bus
by itself and notify the driver.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: 05a1308a2e ("ice: Don't dereference NULL in ice_gnss_read error path")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1a64a151d ]
If caller reports ENOMEM, then stop iterating over the batch and send a
single netlink message to userspace to report OOM.
Fixes: cbb8125eb4 ("netfilter: nfnetlink: deliver netlink errors on batch completion")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 212ed75dc5 ]
The pipapo set backend follows copy-on-update approach, maintaining one
clone of the existing datastructure that is being updated. The clone
and current datastructures are swapped via rcu from the commit step.
The existing integration with the commit protocol is flawed because
there is no operation to clean up the clone if the transaction is
aborted. Moreover, the datastructure swap happens on set element
activation.
This patch adds two new operations for sets: commit and abort, these new
operations are invoked from the commit and abort steps, after the
transactions have been digested, and it updates the pipapo set backend
to use it.
This patch adds a new ->pending_update field to sets to maintain a list
of sets that require this new commit and abort operations.
Fixes: 3c4287f620 ("nf_tables: Add set type for arbitrary concatenation of ranges")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5c31fb71f ]
The DSPI controller has configurable timing for
(a) tCSC: the interval between the assertion of the chip select and the
first clock edge
(b) tASC: the interval between the last clock edge and the deassertion
of the chip select
What is a bit surprising, but is documented in the figure "Example of
continuous transfer (CPHA=1, CONT=1)" in the datasheet, is that when the
chip select stays asserted between multiple TX FIFO writes, the tCSC and
tASC times still apply. With CONT=1, chip select remains asserted, but
SCK takes a break and goes to the idle state for tASC + tCSC ns.
In other words, the default values (of 0 and 0 ns) result in SCK
glitches where the SCK transition to the idle state, as well as the SCK
transition from the idle state, will have no delay in between, and it
may appear that a SCK cycle has simply gone missing. The resulting
timing violation might cause data corruption in many peripherals, as
their chip select is asserted.
The driver has device tree bindings for tCSC ("fsl,spi-cs-sck-delay")
and tASC ("fsl,spi-sck-cs-delay"), but these are only specified to apply
when the chip select toggles in the first place, and this timing
characteristic depends on each peripheral. Many peripherals do not have
explicit timing requirements, so many device trees do not have these
properties present at all.
Nonetheless, the lack of SCK glitches is a common sense requirement, and
since the SCK stays in the idle state during transfers for tCSC+tASC ns,
and that in itself should look like half a cycle, then let's ensure that
tCSC and tASC are at least a quarter of a SCK period, such that their
sum is at least half of one.
Fixes: 95bf15f386 ("spi: fsl-dspi: Add ~50ns delay between cs and sck")
Reported-by: Lisa Chen (陈敏捷) <minjie.chen@geekplus.com>
Debugged-by: Lisa Chen (陈敏捷) <minjie.chen@geekplus.com>
Tested-by: Lisa Chen (陈敏捷) <minjie.chen@geekplus.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20230529223402.1199503-1-vladimir.oltean@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b00683422f ]
There is a reference count error in error path code and a potential race
in check_rkey() in rxe_resp.c. When looking up the rkey for a memory
window the reference to the mw from rxe_lookup_mw() is dropped before a
reference is taken on the mr referenced by the mw. If the mr is destroyed
immediately after the call to rxe_put(mw) the mr pointer is unprotected
and may end up pointing at freed memory. The rxe_get(mr) call should take
place before the rxe_put(mw) call.
All errors in check_rkey() call rxe_put(mw) if mw is not NULL but it was
already called after the above. The mw pointer should be set to NULL after
the rxe_put(mw) call to prevent this from happening.
Fixes: cdd0b85675 ("RDMA/rxe: Implement memory access through MWs")
Link: https://lore.kernel.org/r/20230517211509.1819998-1-rpearsonhpe@gmail.com
Signed-off-by: Bob Pearson <rpearsonhpe@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a3763e873 ]
In rxe_net.c a received packet, from udp or loopback, is passed to
rxe_rcv() in rxe_recv.c as a udp packet. I.e. skb->data is pointing at the
udp header. But rxe_rcv() makes length checks to verify the packet is long
enough to hold the roce headers as if it were a roce
packet. I.e. skb->data pointing at the bth header. A runt packet would
appear to have 8 more bytes than it actually does which may lead to
incorrect behavior.
This patch calls skb_pull() to adjust the skb to point at the bth header
before calling rxe_rcv() which fixes this error.
Fixes: 8700e3e7c4 ("Soft RoCE driver")
Link: https://lore.kernel.org/r/20230517172242.1806340-1-rpearsonhpe@gmail.com
Signed-off-by: Bob Pearson <rpearsonhpe@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c29c8c7df ]
In current design:
1. PD and clt_path->s.dev are shared among connections.
2. every con[n]'s cleanup phase will call destroy_con_cq_qp()
3. clt_path->s.dev will be always decreased in destroy_con_cq_qp(), and
when clt_path->s.dev become zero, it will destroy PD.
4. when con[1] failed to create, con[1] will not take clt_path->s.dev,
but it try to decreased clt_path->s.dev
So, in case create_cm(con[0]) succeeds but create_cm(con[1]) fails,
destroy_con_cq_qp(con[1]) will be called first which will destroy the PD
while this PD is still taken by con[0].
Here, we refactor the error path of create_cm() and init_conns(), so that
we do the cleanup in the order they are created.
The warning occurs when destroying RXE PD whose reference count is not
zero.
rnbd_client L597: Mapping device /dev/nvme0n1 on session client, (access_mode: rw, nr_poll_queues: 0)
------------[ cut here ]------------
WARNING: CPU: 0 PID: 26407 at drivers/infiniband/sw/rxe/rxe_pool.c:256 __rxe_cleanup+0x13a/0x170 [rdma_rxe]
Modules linked in: rpcrdma rdma_ucm ib_iser rnbd_client libiscsi rtrs_client scsi_transport_iscsi rtrs_core rdma_cm iw_cm ib_cm crc32_generic rdma_rxe udp_tunnel ib_uverbs ib_core kmem device_dax nd_pmem dax_pmem nd_vme crc32c_intel fuse nvme_core nfit libnvdimm dm_multipath scsi_dh_rdac scsi_dh_emc scsi_dh_alua dm_mirror dm_region_hash dm_log dm_mod
CPU: 0 PID: 26407 Comm: rnbd-client.sh Kdump: loaded Not tainted 6.2.0-rc6-roce-flush+ #53
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
RIP: 0010:__rxe_cleanup+0x13a/0x170 [rdma_rxe]
Code: 45 84 e4 0f 84 5a ff ff ff 48 89 ef e8 5f 18 71 f9 84 c0 75 90 be c8 00 00 00 48 89 ef e8 be 89 1f fa 85 c0 0f 85 7b ff ff ff <0f> 0b 41 bc ea ff ff ff e9 71 ff ff ff e8 84 7f 1f fa e9 d0 fe ff
RSP: 0018:ffffb09880b6f5f0 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff99401f15d6a8 RCX: 0000000000000000
RDX: 0000000000000001 RSI: ffffffffbac8234b RDI: 00000000ffffffff
RBP: ffff99401f15d6d0 R08: 0000000000000001 R09: 0000000000000001
R10: 0000000000002d82 R11: 0000000000000000 R12: 0000000000000001
R13: ffff994101eff208 R14: ffffb09880b6f6a0 R15: 00000000fffffe00
FS: 00007fe113904740(0000) GS:ffff99413bc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007ff6cde656c8 CR3: 000000001f108004 CR4: 00000000001706f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
rxe_dealloc_pd+0x16/0x20 [rdma_rxe]
ib_dealloc_pd_user+0x4b/0x80 [ib_core]
rtrs_ib_dev_put+0x79/0xd0 [rtrs_core]
destroy_con_cq_qp+0x8a/0xa0 [rtrs_client]
init_path+0x1e7/0x9a0 [rtrs_client]
? __pfx_autoremove_wake_function+0x10/0x10
? lock_is_held_type+0xd7/0x130
? rcu_read_lock_sched_held+0x43/0x80
? pcpu_alloc+0x3dd/0x7d0
? rtrs_clt_init_stats+0x18/0x40 [rtrs_client]
rtrs_clt_open+0x24f/0x5a0 [rtrs_client]
? __pfx_rnbd_clt_link_ev+0x10/0x10 [rnbd_client]
rnbd_clt_map_device+0x6a5/0xe10 [rnbd_client]
Fixes: 6a98d71dae ("RDMA/rtrs: client: main functionality")
Link: https://lore.kernel.org/r/1682384563-2-4-git-send-email-lizhijian@fujitsu.com
Signed-off-by: Li Zhijian <lizhijian@fujitsu.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Tested-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 00f8205ffc upstream.
Consider a scenario where cable disconnect happens when there is an active
usb reqest queued to the UDC. As part of the disconnect we would issue an
end transfer with no interrupt-on-completion before giving back this
request. Since we are giving back the request without skipping TRBs the
num_trbs field of dwc3_request still holds the stale value previously used.
Function drivers re-use same request for a given bind-unbind session and
hence their dwc3_request context gets preserved across cable
disconnect/connect. When such a request gets re-queued after cable connect,
we would increase the num_trbs field on top of the previous stale value
thus incorrectly representing the number of TRBs used. Fix this by
resetting num_trbs field before giving back the request.
Fixes: 09fe1f8d7e ("usb: dwc3: gadget: track number of TRBs per request")
Cc: stable <stable@kernel.org>
Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Message-ID: <1685654850-8468-1-git-send-email-quic_eserrao@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d2d6935422 upstream.
The Qualcomm dwc3 glue driver is currently accessing the driver data of
the child core device during suspend and on wakeup interrupts. This is
clearly a bad idea as the child may not have probed yet or could have
been unbound from its driver.
The first such layering violation was part of the initial version of the
driver, but this was later made worse when the hack that accesses the
driver data of the grand child xhci device to configure the wakeup
interrupts was added.
Fixing this properly is not that easily done, so add a sanity check to
make sure that the child driver data is non-NULL before dereferencing it
for now.
Note that this relies on subtleties like the fact that driver core is
making sure that the parent is not suspended while the child is probing.
Reported-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/all/20230325165217.31069-4-manivannan.sadhasivam@linaro.org/
Fixes: d9152161b4 ("usb: dwc3: Add Qualcomm DWC3 glue layer driver")
Fixes: 6895ea55c3 ("usb: dwc3: qcom: Configure wakeup interrupts during suspend")
Cc: stable@vger.kernel.org # 3.18: a872ab303d: "usb: dwc3: qcom: fix use-after-free on runtime-PM wakeup"
Cc: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
Cc: Krishna Kurapati <quic_kriskura@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Message-ID: <20230607100540.31045-2-johan+linaro@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e6ac852fb upstream.
Currently {modprobe, bind} after {rmmod, unbind} results in probe failure.
genirq: Flags mismatch irq 22. 00000004 (85070400.usb3drd) vs. 00000004 (85070400.usb3drd)
renesas_usb3: probe of 85070000.usb3peri failed with error -16
The reason is, it is trying to register an interrupt handler for the same
IRQ twice. The devm_request_irq() was called with the parent device.
So the interrupt handler won't be unregistered when the usb3-peri device
is unbound.
Fix this issue by replacing "parent dev"->"dev" as the irq resource
is managed by this driver.
Fixes: 9cad72dfc5 ("usb: gadget: Add support for RZ/V2M USB3DRD driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Message-ID: <20230530161720.179927-1-biju.das.jz@bp.renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 286d9975a8 upstream.
usb_udc_connect_control(), soft_connect_store() and
usb_gadget_deactivate() can potentially race against each other to invoke
usb_gadget_connect()/usb_gadget_disconnect(). To prevent this, guard
udc->started, gadget->allow_connect, gadget->deactivate and
gadget->connect with connect_lock so that ->pullup() is only invoked when
the gadget is bound, started and not deactivated. The routines
usb_gadget_connect_locked(), usb_gadget_disconnect_locked(),
usb_udc_connect_control_locked(), usb_gadget_udc_start_locked(),
usb_gadget_udc_stop_locked() are called with this lock held.
An earlier version of this commit was reverted due to the crash reported in
https://lore.kernel.org/all/ZF4BvgsOyoKxdPFF@francesco-nb.int.toradex.com/.
commit 16737e78d190 ("usb: gadget: udc: core: Offload usb_udc_vbus_handler processing")
addresses the crash reported.
Cc: stable@vger.kernel.org
Fixes: 628ef0d273 ("usb: udc: add usb_udc_vbus_handler")
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Message-ID: <20230609010227.978661-2-badhri@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 50966da807 upstream.
usb_udc_vbus_handler() can be invoked from interrupt context by irq
handlers of the gadget drivers, however, usb_udc_connect_control() has
to run in non-atomic context due to the following:
a. Some of the gadget driver implementations expect the ->pullup
callback to be invoked in non-atomic context.
b. usb_gadget_disconnect() acquires udc_lock which is a mutex.
Hence offload invocation of usb_udc_connect_control()
to workqueue.
UDC should not be pulled up unless gadget driver is bound. The new flag
"allow_connect" is now set by gadget_bind_driver() and cleared by
gadget_unbind_driver(). This prevents work item to pull up the gadget
even if queued when the gadget driver is already unbound.
Cc: stable@vger.kernel.org
Fixes: 1016fc0c09 ("USB: gadget: Fix obscure lockdep violation for udc_mutex")
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Message-ID: <20230609010227.978661-1-badhri@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a82c3df955 upstream.
LS1028A is using DMA with LPUART. Having RX watermark set to 1, means
DMA transactions are started only after receiving the second character.
On other platforms with newer LPUART IP, Receiver Idle Empty function
initiates the DMA request after the receiver is idling for 4 characters.
But this feature is missing on LS1028A, which is causing a 1-character
delay in the RX direction on this platform.
Set RX watermark to 0 to initiate RX DMA after each character.
Link: https://lore.kernel.org/linux-serial/20230607103459.1222426-1-robert.hodaszi@digi.com/
Fixes: 9ad9df8447 ("tty: serial: fsl_lpuart: Fix the wrong RXWATER setting for rx dma case")
Cc: stable <stable@kernel.org>
Signed-off-by: Robert Hodaszi <robert.hodaszi@digi.com>
Message-ID: <20230609121334.1878626-1-robert.hodaszi@digi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70c2e03e9a upstream.
Both tb_xdomain_enable_paths() and tb_xdomain_disable_paths() expect -1,
not 0, if the corresponding ring is not needed. For this reason change
the driver to use correct value for the rings that are not needed.
Fixes: 180b068942 ("thunderbolt: Allow multiple DMA tunnels over a single XDomain connection")
Cc: stable@vger.kernel.org
Reported-by: Pengfei Xu <pengfei.xu@intel.com>
Tested-by: Pengfei Xu <pengfei.xu@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3fe95742af upstream.
If the boot firmware has already established tunnels, especially ones
that have special requirements from the link such as DisplayPort, we
should not blindly enable CL states (nor change the TMU configuration).
Otherwise the existing tunnels may not work as expected.
For this reason, skip the CL state enabling when we go over the existing
topology. This will also keep the TMU settings untouched because we do
not change the TMU configuration when CL states are not enabled.
Reported-by: Koba Ko <koba.ko@canonical.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/7831
Cc: stable@vger.kernel.org # v6.0+
Acked-By: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6d572aeb5 upstream.
It turns out that when plugging in VGA cable through USB-C to VGA/DVI
dongle the Connection Manager handshake can take longer time, at least
on Intel Titan Ridge based docks such as Dell WD91TB. This leads to
following error in the dmesg:
thunderbolt 0000:00:0d.3: 3:10: DP tunnel activation failed, aborting
and the display stays blank (because we failed to establish the tunnel).
For this reason increase the timeout to 3s.
Reported-by: Koba Ko <koba.ko@canonical.com>
Cc: stable@vger.kernel.org
Acked-By: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87af86ae89 upstream.
When the preempted IB frame resubmitted to cp, we need to modify the frame
data including:
1. set PRE_RESUME 1 in CONTEXT_CONTROL.
2. use meta data(DE and CE) read from CSA in WRITE_DATA.
Add functions to save the location the first time IBs emitted and callback
to patch the package when resubmission happens.
Signed-off-by: Jiadong Zhu <Jiadong.Zhu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.3.x
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1dbcf770cc upstream.
When MEC executes unmap_queue for mid command buffer preemption, it will
kick the write pointer of the gfx ring, set CP_VMID_PREEMPT to trigger the
preemption and wait for CP_VMID_PREEMPT becomes zero after the preemption
done. There is a race condition that PFP may excute the resetting command
before MEC set CP_VMID_PREEMPT. As a result, hang happens as
CP_VMID_PREEMPT is always 0xffff.
To avoid this, we send resetting CP_VMID_PREEMPT command after the trailing
fence is siganled and update gfx write pointer explicitly.
Signed-off-by: Jiadong Zhu <Jiadong.Zhu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.3.x
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2535
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3eb1a3a040 upstream.
The VBIOS image update flow requires userspace to:
1) Write the image to `psp_vbflash`
2) Read `psp_vbflash`
3) Poll `psp_vbflash_status` to check for completion
If userspace reads `psp_vbflash` before writing an image, it's
possible that it causes problems that can put the dGPU into an invalid
state.
Explicitly check that an image has been written before letting a read
succeed.
Cc: stable@vger.kernel.org
Fixes: 8424f2ccb3 ("drm/amdgpu/psp: Add vbflash sysfs interface support")
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8a5d5ea3b upstream.
This seems to have existed for ever but is now more apparant after
commit 9bff18d134 ("drm/ttm: use per BO cleanup workers")
My analysis: two threads are running, one in the irq signalling the
fence, in dma_fence_signal_timestamp_locked, it has done the
DMA_FENCE_FLAG_SIGNALLED_BIT setting, but hasn't yet reached the
callbacks.
The second thread in nouveau_cli_work_ready, where it sees the fence is
signalled, so then puts the fence, cleanups the object and frees the
work item, which contains the callback.
Thread one goes again and tries to call the callback and causes the
use-after-free.
Proposed fix: lock the fence signalled check in nouveau_cli_work_ready,
so either the callbacks are done or the memory is freed.
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Fixes: 11e451e740 ("drm/nouveau: remove fence wait code from deferred client work handler")
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://lore.kernel.org/dri-devel/20230615024008.1600281-1-airlied@gmail.com/
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 722d908223 upstream.
issue_discard() passes GFP_NOWAIT to __blkdev_issue_discard() despite
its code assuming bio_alloc() always succeeds.
Commit 3dba53a958 ("dm thin: use __blkdev_issue_discard for async
discard support") clearly shows where things went bad:
Before commit 3dba53a958, dm-thin.c's open-coded
__blkdev_issue_discard_async() properly handled using GFP_NOWAIT.
Unfortunately __blkdev_issue_discard() doesn't and it was missed
during review.
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cb65b282c9 upstream.
Must check pmd->fail_io before using pmd->data_sm since
pmd->data_sm may be destroyed by other processes.
P1(kworker) P2(message)
do_worker
process_prepared
process_prepared_discard_passdown_pt2
dm_pool_dec_data_range
pool_message
commit
dm_pool_commit_metadata
↓
// commit failed
metadata_operation_failed
abort_transaction
dm_pool_abort_metadata
__open_or_format_metadata
↓
dm_sm_disk_open
↓
// open failed
// pmd->data_sm is NULL
dm_sm_dec_blocks
↓
// try to access pmd->data_sm --> UAF
As shown above, if dm_pool_commit_metadata() and
dm_pool_abort_metadata() fail in pool_message process, kworker may
trigger UAF.
Fixes: be500ed721 ("dm space maps: improve performance with inc/dec on ranges of blocks")
Cc: stable@vger.kernel.org
Signed-off-by: Li Lingfeng <lilingfeng3@huawei.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 78d0f94902 upstream.
This patch prevents the system from crashing when unloading the ISM module.
How to reproduce: Attach an ISM device and execute 'rmmod ism'.
Error-Log:
- Trying to free already-free IRQ 0
- WARNING: CPU: 1 PID: 966 at kernel/irq/manage.c:1890 free_irq+0x140/0x540
After calling ism_dev_exit() for each ISM device in the exit routine,
pci_unregister_driver() will execute ism_remove() for each ISM device.
Because ism_remove() also calls ism_dev_exit(),
free_irq(pci_irq_vector(pdev, 0), ism) is called twice for each ISM
device. This results in a crash with the error
'Trying to free already-free IRQ'.
In the exit routine, it is enough to call pci_unregister_driver()
because it ensures that ism_dev_exit() is called once per
ISM device.
Cc: <stable@vger.kernel.org> # 6.3+
Fixes: 89e7d2ba61 ("net/ism: Add new API for client registration")
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Julian Ruess <julianr@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 122e2cb7e1 upstream.
This commit adds new DEVICE_FLG with QUIRK_FLAG_DSD_RAW and Vendor Id for
HEM devices which supports native DSD. Prior to this change Linux kernel
was not enabling native DSD playback for HEM devices, and as a result,
DSD audio was being converted to PCM "on the fly". HEM devices,
when connected to the system, would only play audio in PCM format,
even if the source material was in DSD format. With the addition of new
VENDOR_FLG in the quircks.c file, the devices are now correctly
recognized, and raw DSD data is transmitted to the device,
allowing for native DSD playback.
Signed-off-by: Lukasz Tyl <ltyl@hem-e.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230614122524.30271-1-ltyl@hem-e.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ba61c9f6c upstream.
As reported in the bugzilla below, the PM resume of a UAC3 device may
fail due to the incomplete power state change, stuck at D1. The
reason is that the driver expects the full D0 power state change only
at hw_params, while the normal PCM resume procedure doesn't call
hw_params.
For fixing the bug, we add the same power state update to D0 at the
prepare callback, which is certainly called by the resume procedure.
Note that, with this change, the power state change in the hw_params
becomes almost redundant, since snd_usb_hw_params() doesn't touch the
parameters (at least it tires so). But dropping it is still a bit
risky (e.g. we have the media-driver binding), so I leave the D0 power
state change in snd_usb_hw_params() as is for now.
Fixes: a0a4959eb4 ("ALSA: usb-audio: Operate UAC3 Power Domains in PCM callbacks")
Cc: <stable@vger.kernel.org>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217539
Link: https://lore.kernel.org/r/20230612132818.29486-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit deccae40e4 upstream.
Commit 619104ba45 ("btrfs: move common NOCOW checks against a file
extent into a helper") changed our call to btrfs_cross_ref_exist() to
always pass false for the 'strict' parameter. We're passing this down
through the stack so that we can do a full check for cross references
during swapfile activation.
With strict always false, this test fails:
btrfs subvol create swappy
chattr +C swappy
fallocate -l1G swappy/swapfile
chmod 600 swappy/swapfile
mkswap swappy/swapfile
btrfs subvol snap swappy swapsnap
btrfs subvol del -C swapsnap
btrfs fi sync /
sync;sync;sync
swapon swappy/swapfile
The fix is to just use args->strict, and everyone except swapfile
activation is passing false.
Fixes: 619104ba45 ("btrfs: move common NOCOW checks against a file extent into a helper")
CC: stable@vger.kernel.org # 6.1+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7833b86595 upstream.
can_nocow_extent can reduce the len passed in, which needs to be
propagated to btrfs_dio_iomap_begin so that iomap does not submit
more data then is mapped.
This problems exists since the btrfs_get_blocks_direct helper was added
in commit c5794e5178 ("btrfs: Factor out write portion of
btrfs_get_blocks_direct"), but the ordered_extent splitting added in
commit b73a6fd1b1 ("btrfs: split partial dio bios before submit")
added a WARN_ON that made a syzkaller test fail.
Reported-by: syzbot+ee90502d5c8fd1d0dd93@syzkaller.appspotmail.com
Fixes: c5794e5178 ("btrfs: Factor out write portion of btrfs_get_blocks_direct")
CC: stable@vger.kernel.org # 6.1+
Tested-by: syzbot+ee90502d5c8fd1d0dd93@syzkaller.appspotmail.com
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 745806fb45 upstream.
[BUG]
Syzbot reports a reproducible ASSERT() when using rescue=usebackuproot
mount option on a corrupted fs.
The full report can be found here:
https://syzkaller.appspot.com/bug?extid=c4614eae20a166c25bf0
BTRFS error (device loop0: state C): failed to load root csum
assertion failed: !tmp, in fs/btrfs/disk-io.c:1103
------------[ cut here ]------------
kernel BUG at fs/btrfs/ctree.h:3664!
invalid opcode: 0000 [#1] PREEMPT SMP KASAN
CPU: 1 PID: 3608 Comm: syz-executor356 Not tainted 6.0.0-rc7-syzkaller-00029-g3800a713b607 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 08/26/2022
RIP: 0010:assertfail+0x1a/0x1c fs/btrfs/ctree.h:3663
RSP: 0018:ffffc90003aaf250 EFLAGS: 00010246
RAX: 0000000000000032 RBX: 0000000000000000 RCX: f21c13f886638400
RDX: 0000000000000000 RSI: 0000000080000000 RDI: 0000000000000000
RBP: ffff888021c640a0 R08: ffffffff816bd38d R09: ffffed10173667f1
R10: ffffed10173667f1 R11: 1ffff110173667f0 R12: dffffc0000000000
R13: ffff8880229c21f7 R14: ffff888021c64060 R15: ffff8880226c0000
FS: 0000555556a73300(0000) GS:ffff8880b9b00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055a2637d7a00 CR3: 00000000709c4000 CR4: 00000000003506e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
btrfs_global_root_insert+0x1a7/0x1b0 fs/btrfs/disk-io.c:1103
load_global_roots_objectid+0x482/0x8c0 fs/btrfs/disk-io.c:2467
load_global_roots fs/btrfs/disk-io.c:2501 [inline]
btrfs_read_roots fs/btrfs/disk-io.c:2528 [inline]
init_tree_roots+0xccb/0x203c fs/btrfs/disk-io.c:2939
open_ctree+0x1e53/0x33df fs/btrfs/disk-io.c:3574
btrfs_fill_super+0x1c6/0x2d0 fs/btrfs/super.c:1456
btrfs_mount_root+0x885/0x9a0 fs/btrfs/super.c:1824
legacy_get_tree+0xea/0x180 fs/fs_context.c:610
vfs_get_tree+0x88/0x270 fs/super.c:1530
fc_mount fs/namespace.c:1043 [inline]
vfs_kern_mount+0xc9/0x160 fs/namespace.c:1073
btrfs_mount+0x3d3/0xbb0 fs/btrfs/super.c:1884
[CAUSE]
Since the introduction of global roots, we handle
csum/extent/free-space-tree roots as global roots, even if no
extent-tree-v2 feature is enabled.
So for regular csum/extent/fst roots, we load them into
fs_info::global_root_tree rb tree.
And we should not expect any conflicts in that rb tree, thus we have an
ASSERT() inside btrfs_global_root_insert().
But rescue=usebackuproot can break the assumption, as we will try to
load those trees again and again as long as we have bad roots and have
backup roots slot remaining.
So in that case we can have conflicting roots in the rb tree, and
triggering the ASSERT() crash.
[FIX]
We can safely remove that ASSERT(), as the caller will properly put the
offending root.
To make further debugging easier, also add two explicit error messages:
- Error message for conflicting global roots
- Error message when using backup roots slot
Reported-by: syzbot+a694851c6ab28cbcfb9c@syzkaller.appspotmail.com
Fixes: abed4aaae4 ("btrfs: track the csum, extent, and free space trees in a rb tree")
CC: stable@vger.kernel.org # 6.1+
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 981a37bab5 upstream.
The async discard uses the BTRFS_FS_DISCARD_RUNNING bit in the fs_info
to force discards off when the filesystem has aborted or we're generally
not able to run discards. This gets flipped on when we're mounted rw,
and also when we go from ro->rw.
Commit 63a7cb1307 ("btrfs: auto enable discard=async when possible")
enabled async discard by default, and this meant
"mount -o ro /dev/xxx /yyy" had async discards turned on.
Unfortunately, this meant our check in btrfs_remount_cleanup() would see
that discards are already on:
/* If we toggled discard async */
if (!btrfs_raw_test_opt(old_opts, DISCARD_ASYNC) &&
btrfs_test_opt(fs_info, DISCARD_ASYNC))
btrfs_discard_resume(fs_info);
So, we'd never call btrfs_discard_resume() when remounting the root
filesystem from ro->rw.
drgn shows this really nicely:
import os
import sys
from drgn.helpers.linux.fs import path_lookup
from drgn import NULL, Object, Type, cast
def btrfs_sb(sb):
return cast("struct btrfs_fs_info *", sb.s_fs_info)
if len(sys.argv) == 1:
path = "/"
else:
path = sys.argv[1]
fs_info = cast("struct btrfs_fs_info *", path_lookup(prog, path).mnt.mnt_sb.s_fs_info)
BTRFS_FS_DISCARD_RUNNING = 1 << prog['BTRFS_FS_DISCARD_RUNNING']
if fs_info.flags & BTRFS_FS_DISCARD_RUNNING:
print("discard running flag is on")
else:
print("discard running flag is off")
[root]# mount | grep nvme
/dev/nvme0n1p3 on / type btrfs
(rw,relatime,compress-force=zstd:3,ssd,discard=async,space_cache=v2,subvolid=5,subvol=/)
[root]# ./discard_running.drgn
discard running flag is off
[root]# mount -o remount,discard=sync /
[root]# mount -o remount,discard=async /
[root]# ./discard_running.drgn
discard running flag is on
The fix is to call btrfs_discard_resume() when we're going from ro->rw.
It already checks to make sure the async discard flag is on, so it'll do
the right thing.
Fixes: 63a7cb1307 ("btrfs: auto enable discard=async when possible")
CC: stable@vger.kernel.org # 6.3+
Reviewed-by: Boris Burkov <boris@bur.io>
Signed-off-by: Chris Mason <clm@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 917ac77846 upstream.
[BUG]
Test case btrfs/027 would crash with subpage (64K page size, 4K
sectorsize) with the following dying messages:
debug: map_length=16384 length=65536 type=metadata|raid6(0x104)
assertion failed: map_length >= length, in fs/btrfs/volumes.c:8093
------------[ cut here ]------------
kernel BUG at fs/btrfs/messages.c:259!
Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015
Call trace:
btrfs_assertfail+0x28/0x2c [btrfs]
btrfs_map_repair_block+0x150/0x2b8 [btrfs]
btrfs_repair_io_failure+0xd4/0x31c [btrfs]
btrfs_read_extent_buffer+0x150/0x16c [btrfs]
read_tree_block+0x38/0xbc [btrfs]
read_tree_root_path+0xfc/0x1bc [btrfs]
btrfs_get_root_ref.part.0+0xd4/0x3a8 [btrfs]
open_ctree+0xa30/0x172c [btrfs]
btrfs_mount_root+0x3c4/0x4a4 [btrfs]
legacy_get_tree+0x30/0x60
vfs_get_tree+0x28/0xec
vfs_kern_mount.part.0+0x90/0xd4
vfs_kern_mount+0x14/0x28
btrfs_mount+0x114/0x418 [btrfs]
legacy_get_tree+0x30/0x60
vfs_get_tree+0x28/0xec
path_mount+0x3e0/0xb64
__arm64_sys_mount+0x200/0x2d8
invoke_syscall+0x48/0x114
el0_svc_common.constprop.0+0x60/0x11c
do_el0_svc+0x38/0x98
el0_svc+0x40/0xa8
el0t_64_sync_handler+0xf4/0x120
el0t_64_sync+0x190/0x194
Code: aa0403e2 b0fff060 91010000 959c2024 (d4210000)
[CAUSE]
In btrfs/027 we test RAID6 with missing devices, in this particular
case, we're repairing a metadata at the end of a data stripe.
But at btrfs_repair_io_failure(), we always pass a full PAGE for repair,
and for subpage case this can cross stripe boundary and lead to the
above BUG_ON().
This metadata repair code is always there, since the introduction of
subpage support, but this can trigger BUG_ON() after the bio split
ability at btrfs_map_bio().
[FIX]
Instead of passing the old PAGE_SIZE, we calculate the correct length
based on the eb size and page size for both regular and subpage cases.
CC: stable@vger.kernel.org # 6.3+
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 34e5a54327 upstream.
This reverts commit c105518679.
This patch disables the TOPDOWN flag for APU and few dGPU cards
which has the VRAM size equal to the BAR size.
When we enable the TOPDOWN flag, we get the free blocks at
the highest available memory region and we don't split the
lower order blocks. This change is required to keep off
the fragmentation related issues particularly in ASIC
which has VRAM space <= 500MiB
Hence, we are reverting this patch.
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2270
Signed-off-by: Arunpravin Paneer Selvam <Arunpravin.PaneerSelvam@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cac9e4418f upstream.
If the application sets ->msg_control and we have to later retry this
command, or if it got queued with IOSQE_ASYNC to begin with, then we
need to retain the original msg_control value. This is due to the net
stack overwriting this field with an in-kernel pointer, to copy it
in. Hitting that path for the second time will now fail the copy from
user, as it's attempting to copy from a non-user address.
Cc: stable@vger.kernel.org # 5.10+
Link: https://github.com/axboe/liburing/issues/880
Reported-and-tested-by: Marek Majkowski <marek@cloudflare.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92c5d1b860 upstream.
The current sanity check for nilfs2 geometry information lacks checks for
the number of segments stored in superblocks, so even for device images
that have been destructively truncated or have an unusually high number of
segments, the mount operation may succeed.
This causes out-of-bounds block I/O on file system block reads or log
writes to the segments, the latter in particular causing
"a_ops->writepages" to repeatedly fail, resulting in sync_inodes_sb() to
hang.
Fix this issue by checking the number of segments stored in the superblock
and avoiding mounting devices that can cause out-of-bounds accesses. To
eliminate the possibility of overflow when calculating the number of
blocks required for the device from the number of segments, this also adds
a helper function to calculate the upper bound on the number of segments
and inserts a check using it.
Link: https://lkml.kernel.org/r/20230526021332.3431-1-konishi.ryusuke@gmail.com
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Reported-by: syzbot+7d50f1e54a12ba3aeae2@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=7d50f1e54a12ba3aeae2
Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fee5eaecca upstream.
Syzbot reports that in its stress test for resize ioctl, the log writing
function nilfs_segctor_do_construct hits a WARN_ON in
nilfs_segctor_truncate_segments().
It turned out that there is a problem with the current implementation of
the resize ioctl, which changes the writable range on the device (the
range of allocatable segments) at the end of the resize process.
This order is necessary for file system expansion to avoid corrupting the
superblock at trailing edge. However, in the case of a file system
shrink, if log writes occur after truncating out-of-bounds trailing
segments and before the resize is complete, segments may be allocated from
the truncated space.
The userspace resize tool was fine as it limits the range of allocatable
segments before performing the resize, but it can run into this issue if
the resize ioctl is called alone.
Fix this issue by changing nilfs_sufile_resize() to update the range of
allocatable segments immediately after successful truncation of segment
space in case of file system shrink.
Link: https://lkml.kernel.org/r/20230524094348.3784-1-konishi.ryusuke@gmail.com
Fixes: 4e33f9eab0 ("nilfs2: implement resize ioctl")
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Reported-by: syzbot+33494cd0df2ec2931851@syzkaller.appspotmail.com
Closes: https://lkml.kernel.org/r/0000000000005434c405fbbafdc5@google.com
Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 270aa01062 upstream.
Patch series "mm/uffd: Fix vma merge/split", v2.
This series contains two patches that fix vma merge/split for userfaultfd
on two separate issues.
Patch 1 fixes a regression since 6.1+ due to something we overlooked when
converting to maple tree apis. The plan is we use patch 1 to replace the
commit "2f628010799e (mm: userfaultfd: avoid passing an invalid range to
vma_merge())" in mm-hostfixes-unstable tree if possible, so as to bring
uffd vma operations back aligned with the rest code again.
Patch 2 fixes a long standing issue that vma can be left unmerged even if
we can for either uffd register or unregister.
Many thanks to Lorenzo on either noticing this issue from the assert
movement patch, looking at this problem, and also provided a reproducer on
the unmerged vma issue [1].
[1] https://gist.github.com/lorenzo-stoakes/a11a10f5f479e7a977fc456331266e0e
This patch (of 2):
It seems vma merging with uffd paths is broken with either
register/unregister, where right now we can feed wrong parameters to
vma_merge() and it's found by recent patch which moved asserts upwards in
vma_merge() by Lorenzo Stoakes:
https://lore.kernel.org/all/ZFunF7DmMdK05MoF@FVFF77S0Q05N.cambridge.arm.com/
It's possible that "start" is contained within vma but not clamped to its
start. We need to convert this into either "cannot merge" case or "can
merge" case 4 which permits subdivision of prev by assigning vma to prev.
As we loop, each subsequent VMA will be clamped to the start.
This patch will eliminate the report and make sure vma_merge() calls will
become legal again.
One thing to mention is that the "Fixes: 29417d292bd0" below is there only
to help explain where the warning can start to trigger, the real commit to
fix should be 69dbe6daf1. Commit 29417d292b helps us to identify the
issue, but unfortunately we may want to keep it in Fixes too just to ease
kernel backporters for easier tracking.
Link: https://lkml.kernel.org/r/20230517190916.3429499-1-peterx@redhat.com
Link: https://lkml.kernel.org/r/20230517190916.3429499-2-peterx@redhat.com
Fixes: 69dbe6daf1 ("userfaultfd: use maple tree iterator to iterate VMAs")
Signed-off-by: Peter Xu <peterx@redhat.com>
Reported-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com>
Reviewed-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Closes: https://lore.kernel.org/all/ZFunF7DmMdK05MoF@FVFF77S0Q05N.cambridge.arm.com/
Cc: Lorenzo Stoakes <lstoakes@gmail.com>
Cc: Mike Rapoport (IBM) <rppt@kernel.org>
Cc: Liam R. Howlett <Liam.Howlett@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85041e1241 upstream.
The given value of 1518 seems to refer to the layer 2 ethernet frame
size without 802.1Q tag. Actual use of the "max-frame-size" including in
the consumer of the "altr,tse-1.0" compatible is the MTU.
Fixes: 95acd4c7b6 ("nios2: Device tree support")
Fixes: 61c610ec61 ("nios2: Add Max10 device tree")
Cc: <stable@vger.kernel.org>
Signed-off-by: Janne Grunau <j@jannau.net>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0bdf0efa18 upstream.
Before storing a page, zswap first checks if the number of stored pages
exceeds the limit specified by memory.zswap.max, for each cgroup in the
hierarchy. If this limit is reached or exceeded, then zswap shrinking is
triggered and short-circuits the store attempt.
However, since the zswap's LRU is not memcg-aware, this can create the
following pathological behavior: the cgroup whose zswap limit is 0 will
evict pages from other cgroups continually, without lowering its own zswap
usage. This means the shrinking will continue until the need for swap
ceases or the pool becomes empty.
As a result of this, we observe a disproportionate amount of zswap
writeback and a perpetually small zswap pool in our experiments, even
though the pool limit is never hit.
More generally, a cgroup might unnecessarily evict pages from other
cgroups before we drive the memcg back below its limit.
This patch fixes the issue by rejecting zswap store attempt without
shrinking the pool when obj_cgroup_may_zswap() returns false.
[akpm@linux-foundation.org: fix return of unintialized value]
[akpm@linux-foundation.org: s/ENOSPC/ENOMEM/]
Link: https://lkml.kernel.org/r/20230530222440.2777700-1-nphamcs@gmail.com
Link: https://lkml.kernel.org/r/20230530232435.3097106-1-nphamcs@gmail.com
Fixes: f4840ccfca ("zswap: memcg accounting")
Signed-off-by: Nhat Pham <nphamcs@gmail.com>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Domenico Cerasuolo <cerasuolodomenico@gmail.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Vitaly Wool <vitaly.wool@konsulko.com>
Cc: Yosry Ahmed <yosryahmed@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 50d927880e upstream.
It's trivial to trigger a use-after-free bug in the ocfs2 quotas code using
fstest generic/452. After a read-only remount, quotas are suspended and
ocfs2_mem_dqinfo is freed through ->ocfs2_local_free_info(). When unmounting
the filesystem, an UAF access to the oinfo will eventually cause a crash.
BUG: KASAN: slab-use-after-free in timer_delete+0x54/0xc0
Read of size 8 at addr ffff8880389a8208 by task umount/669
...
Call Trace:
<TASK>
...
timer_delete+0x54/0xc0
try_to_grab_pending+0x31/0x230
__cancel_work_timer+0x6c/0x270
ocfs2_disable_quotas.isra.0+0x3e/0xf0 [ocfs2]
ocfs2_dismount_volume+0xdd/0x450 [ocfs2]
generic_shutdown_super+0xaa/0x280
kill_block_super+0x46/0x70
deactivate_locked_super+0x4d/0xb0
cleanup_mnt+0x135/0x1f0
...
</TASK>
Allocated by task 632:
kasan_save_stack+0x1c/0x40
kasan_set_track+0x21/0x30
__kasan_kmalloc+0x8b/0x90
ocfs2_local_read_info+0xe3/0x9a0 [ocfs2]
dquot_load_quota_sb+0x34b/0x680
dquot_load_quota_inode+0xfe/0x1a0
ocfs2_enable_quotas+0x190/0x2f0 [ocfs2]
ocfs2_fill_super+0x14ef/0x2120 [ocfs2]
mount_bdev+0x1be/0x200
legacy_get_tree+0x6c/0xb0
vfs_get_tree+0x3e/0x110
path_mount+0xa90/0xe10
__x64_sys_mount+0x16f/0x1a0
do_syscall_64+0x43/0x90
entry_SYSCALL_64_after_hwframe+0x72/0xdc
Freed by task 650:
kasan_save_stack+0x1c/0x40
kasan_set_track+0x21/0x30
kasan_save_free_info+0x2a/0x50
__kasan_slab_free+0xf9/0x150
__kmem_cache_free+0x89/0x180
ocfs2_local_free_info+0x2ba/0x3f0 [ocfs2]
dquot_disable+0x35f/0xa70
ocfs2_susp_quotas.isra.0+0x159/0x1a0 [ocfs2]
ocfs2_remount+0x150/0x580 [ocfs2]
reconfigure_super+0x1a5/0x3a0
path_mount+0xc8a/0xe10
__x64_sys_mount+0x16f/0x1a0
do_syscall_64+0x43/0x90
entry_SYSCALL_64_after_hwframe+0x72/0xdc
Link: https://lkml.kernel.org/r/20230522102112.9031-1-lhenriques@suse.de
Signed-off-by: Luís Henriques <lhenriques@suse.de>
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Tested-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7e60032c6 upstream.
This should use wiphy_lock() now instead of requiring the
RTNL, since __cfg80211_leave() via cfg80211_leave() is now
requiring that lock to be held.
Fixes: a05829a722 ("cfg80211: avoid holding the RTNL when calling the driver")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 91539341a3 ]
When checking for OF quirks, make sure either 'compatible' or 'property'
is set, and give up otherwise.
This avoids non-OF quirks being randomly applied as they don't have any
of the OF data that need checking.
Cc: Douglas Anderson <dianders@chromium.org>
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: 44bd78dd2b ("irqchip/gic-v3: Disable pseudo NMIs on Mediatek devices w/ firmware issues")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 533ab73f5b ]
The sq thread actively releases CPU resources by calling the
cond_resched() and schedule() interfaces when it is idle. Therefore,
more resources are available for other threads to run.
There exists a problem in sq thread: it does not unlock sqd->lock before
releasing CPU resources every time. This makes other threads pending on
sqd->lock for a long time. For example, the following interfaces all
require sqd->lock: io_sq_offload_create(), io_register_iowq_max_workers()
and io_ring_exit_work().
Before the sq thread releases CPU resources, unlocking sqd->lock will
provide the user a better experience because it can respond quickly to
user requests.
Signed-off-by: Kanchan Joshi<joshi.k@samsung.com>
Signed-off-by: Wenwen Chen<wenwen.chen@samsung.com>
Link: https://lore.kernel.org/r/20230525082626.577862-1-wenwen.chen@samsung.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6ebaa8100 ]
The existing code silently converts read operations with the
REQ_FUA bit set into write-barrier operations. This results in data
loss as the backend scribbles zeroes over the data instead of returning
it.
While the REQ_FUA bit doesn't make sense on a read operation, at least
one well-known out-of-tree kernel module does set it and since it
results in data loss, let's be safe here and only look at REQ_FUA for
writes.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Acked-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20230426164005.2213139-1-ross.lagerwall@citrix.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4897a898a2 ]
PAGE_OFFSET is technically a virtual address so when checking the value of
initrd_start against it we should make sure that it has been sanitised from
the values passed by the bootloader. Without this change, even with a bootloader
that passes correct addresses for an initrd, we are failing to load it on MT7621
boards, for example.
Signed-off-by: Liviu Dudau <liviu@dudau.co.uk>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d645604f6 ]
Various fixes for the Au1200/Au1550/Au1300 DBDMA2 code:
- skip cache invalidation if chip has working coherency circuitry.
- invalidate KSEG0-portion of the (physical) data address.
- force the dma channel doorbell write out to bus immediately with
a sync.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2041708de ]
The Au1300, at least the one I have to test, uses the NetLogic vendor
ID, but commit 95b8a5e011 ("MIPS: Remove NETLOGIC support") also
dropped Au1300 detection. Restore Au1300 detection.
Tested on DB1300 with Au1380 chip.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75b18aac6f ]
Alchemy DB1200/DB1300 boards can use the pata_platform driver.
Unhide the config entry in all of MIPS.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59fa12646d ]
Add comment in arch_sync_dma_for_device() and handle the direction flag in
arch_sync_dma_for_cpu().
When receiving data from the device (DMA_FROM_DEVICE) unconditionally
purge the data cache in arch_sync_dma_for_cpu().
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cfcb942863 ]
Avoid early devlink info return if errors arise with MCDI commands
executed for getting the required info from the device. The rationale
is some commands can fail but later ones could still give useful data.
Moreover, some nvram partitions could not be present which needs to be
handled as a non error.
The specific errors are reported through system messages and if any
error appears, it will be reported generically through extack.
Fixes 14743ddd24 ("sfc: add devlink info support for ef100")
Signed-off-by: Alejandro Lucero <alejandro.lucero-palau@amd.com>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e123036be3 ]
In the BE hw_params configuration, the existing code checks if any of the
existing FEs are prepared, running, paused or suspended - and skips the
configuration in those cases. This allows multiple calls of hw_params
which the ALSA state machine supports.
This check is not handled for the prepare stage, which can lead to the
same BE being prepared multiple times. This patch adds a check similar to
that of the hw_params, with the main difference being that the suspended
state is allowed: the ALSA state machine allows a transition from
suspended to prepared with hw_params skipped.
This problem was detected on Intel IPC4/SoundWire devices, where the BE
dailink .prepare stage is used to configure the SoundWire stream with a
bank switch. Multiple .prepare calls lead to conflicts with the .trigger
operation with IPC4 configurations. This problem was not detected earlier
on Intel devices, HDaudio BE dailinks detect that the link is already
prepared and skip the configuration, and for IPC3 devices there is no BE
trigger.
Link: https://github.com/thesofproject/sof/issues/7596
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Link: https://lore.kernel.org/r/20230517185731.487124-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 806570c0bb ]
Since f8a53bb58e ("btrfs: handle checksum generation in the storage
layer") the failures of btrfs_csum_one_bio() are handled via
bio_end_io().
This means, we can return BLK_STS_RESOURCE from btrfs_csum_one_bio() in
case the allocation of the ordered sums fails.
This also fixes a syzkaller report, where injecting a failure into the
kvzalloc() call results in a BUG_ON().
Reported-by: syzbot+d8941552e21eac774778@syzkaller.appspotmail.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7561551e7b ]
Currently we allow a block group not to be marked read-only for scrub.
But for RAID56 block groups if we require the block group to be
read-only, then we're allowed to use cached content from scrub stripe to
reduce unnecessary RAID56 reads.
So this patch would:
- Make btrfs_inc_block_group_ro() try harder
During my tests, for cases like btrfs/061 and btrfs/064, we can hit
ENOSPC from btrfs_inc_block_group_ro() calls during scrub.
The reason is if we only have one single data chunk, and trying to
scrub it, we won't have any space left for any newer data writes.
But this check should be done by the caller, especially for scrub
cases we only temporarily mark the chunk read-only.
And newer data writes would always try to allocate a new data chunk
when needed.
- Return error for scrub if we failed to mark a RAID56 chunk read-only
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95339f40a8 ]
The logic used for power_supply_is_system_supplied() counts all power
supplies and assumes that the system is running from AC if there is
either a non-battery power-supply reporting to be online or if no
power-supplies exist at all.
The second rule is for desktop systems, that don't have any
battery/charger devices. These systems will incorrectly report to be
powered from battery once a device scope power-supply is registered
(e.g. a HID device), since these power-supplies increase the counter.
Apart from HID devices, recent dGPUs provide UCSI power supplies on a
desktop systems. The dGPU by default doesn't have anything plugged in so
it's 'offline'. This makes power_supply_is_system_supplied() return 0
with a count of 1 meaning all drivers that use this get a wrong judgement.
To fix this case adjust the logic to also examine the scope of the power
supply. If the power supply is deemed a device power supply, then don't
count it.
Cc: Evan Quan <Evan.Quan@amd.com>
Suggested-by: Lijo Lazar <Lijo.Lazar@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44bd78dd2b ]
Some Chromebooks with Mediatek SoCs have a problem where the firmware
doesn't properly save/restore certain GICR registers. Newer
Chromebooks should fix this issue and we may be able to do firmware
updates for old Chromebooks. At the moment, the only known issue with
these Chromebooks is that we can't enable "pseudo NMIs" since the
priority register can be lost. Enabling "pseudo NMIs" on Chromebooks
with the problematic firmware causes crashes and freezes.
Let's detect devices with this problem and then disable "pseudo NMIs"
on them. We'll detect the problem by looking for the presence of the
"mediatek,broken-save-restore-fw" property in the GIC device tree
node. Any devices with fixed firmware will not have this property.
Our detection plan works because we never bake a Chromebook's device
tree into firmware. Instead, device trees are always bundled with the
kernel. We'll update the device trees of all affected Chromebooks and
then we'll never enable "pseudo NMI" on a kernel that is bundled with
old device trees. When a firmware update is shipped that fixes this
issue it will know to patch the device tree to remove the property.
In order to make this work, the quick detection mechanism of the GICv3
code is extended to be able to look for properties in addition to
looking at "compatible".
Reviewed-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230515131353.v2.2.I88dc0a0eb1d9d537de61604cd8994ecc55c0cac1@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 362c1f2ec8 ]
On ASUS GU604V the key 0x7B is issued when the charger is connected or
disconnected, and key 0xC0 is issued when an external display is
connected or disconnected.
This commit maps them to KE_IGNORE to slience kernel messages about
unknown keys, such as:
kernel: asus_wmi: Unknown key code 0x7b
Signed-off-by: Alexandru Sorodoc <ealex95@gmail.com>
Link: https://lore.kernel.org/r/20230512101517.47416-1-ealex95@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 155c45a256 ]
Reduce the amount of output this dev_dbg() statement emits into logs,
otherwise if system software polls the sysfs entry for data and keeps
getting -ENODATA, it could end up filling the logs up.
This does in fact make systemd journald choke, since during boot the
sysfs power supply entries are polled and if journald starts at the
same time, the journal is just being repeatedly filled up, and the
system stops on trying to start journald without booting any further.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 976d3c6778 ]
According to Mirsad the gpio-sim.sh test appears to FAIL in a wrong way
due to missing initialisation of shell variables:
4.2. Bias settings work correctly
cat: /sys/devices/platform/gpio-sim.0/gpiochip18/sim_gpio0/value: No such file or directory
./gpio-sim.sh: line 393: test: =: unary operator expected
bias setting does not work
GPIO gpio-sim test FAIL
After this change the test passed:
4.2. Bias settings work correctly
GPIO gpio-sim test PASS
His testing environment is AlmaLinux 8.7 on Lenovo desktop box with
the latest Linux kernel based on v6.2:
Linux 6.2.0-mglru-kmlk-andy-09238-gd2980d8d8265 x86_64
Suggested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr>
Signed-off-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d5c129d6c ]
sc27xx_fgu_external_power_changed() dereferences data->battery,
which gets sets in ab8500_btemp_probe() like this:
data->battery = devm_power_supply_register(dev, &sc27xx_fgu_desc,
&fgu_cfg);
As soon as devm_power_supply_register() has called device_add()
the external_power_changed callback can get called. So there is a window
where sc27xx_fgu_external_power_changed() may get called while
data->battery has not been set yet leading to a NULL pointer dereference.
Fixing this is easy. The external_power_changed callback gets passed
the power_supply which will eventually get stored in data->battery,
so sc27xx_fgu_external_power_changed() can simply directly use
the passed in psy argument which is always valid.
After this change sc27xx_fgu_external_power_changed() is reduced to just
"power_supply_changed(psy);" and it has the same prototype. While at it
simply replace it with making the external_power_changed callback
directly point to power_supply_changed.
Cc: Orson Zhai <orsonzhai@gmail.com>
Cc: Chunyan Zhang <zhang.lyra@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5299ce4e9 ]
ab8500_btemp_external_power_changed() dereferences di->btemp_psy,
which gets sets in ab8500_btemp_probe() like this:
di->btemp_psy = devm_power_supply_register(dev, &ab8500_btemp_desc,
&psy_cfg);
As soon as devm_power_supply_register() has called device_add()
the external_power_changed callback can get called. So there is a window
where ab8500_btemp_external_power_changed() may get called while
di->btemp_psy has not been set yet leading to a NULL pointer dereference.
Fixing this is easy. The external_power_changed callback gets passed
the power_supply which will eventually get stored in di->btemp_psy,
so ab8500_btemp_external_power_changed() can simply directly use
the passed in psy argument which is always valid.
And the same applies to ab8500_fg_external_power_changed().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c1bcf2d3e ]
This patch add the validation for smb request protocol id.
If it is not one of the four ids(SMB1_PROTO_NUMBER, SMB2_PROTO_NUMBER,
SMB2_TRANSFORM_PROTO_NUM, SMB2_COMPRESSION_TRANSFORM_ID), don't allow
processing the request. And this will fix the following KASAN warning
also.
[ 13.905265] BUG: KASAN: slab-out-of-bounds in init_smb2_rsp_hdr+0x1b9/0x1f0
[ 13.905900] Read of size 16 at addr ffff888005fd2f34 by task kworker/0:2/44
...
[ 13.908553] Call Trace:
[ 13.908793] <TASK>
[ 13.908995] dump_stack_lvl+0x33/0x50
[ 13.909369] print_report+0xcc/0x620
[ 13.910870] kasan_report+0xae/0xe0
[ 13.911519] kasan_check_range+0x35/0x1b0
[ 13.911796] init_smb2_rsp_hdr+0x1b9/0x1f0
[ 13.912492] handle_ksmbd_work+0xe5/0x820
Cc: stable@vger.kernel.org
Reported-by: Chih-Yen Chang <cc85nod@gmail.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee13b50087 ]
The Qualcomm LLCC/EDAC drivers were using a fixed register stride for
accessing the (Control and Status Registers) CSRs of each LLCC bank.
This stride only works for some SoCs like SDM845 for which driver
support was initially added.
But the later SoCs use different register stride that vary between the
banks with holes in-between. So it is not possible to use a single register
stride for accessing the CSRs of each bank. By doing so could result in a
crash.
For fixing this issue, let's obtain the base address of each LLCC bank from
devicetree and get rid of the fixed stride. This also means, there is no
need to rely on reg-names property and the base addresses can be obtained
using the index.
First index is LLCC bank 0 and last index is LLCC broadcast. If the SoC
supports more than one bank, then those need to be defined in devicetree
for index from 1..N-1.
Reported-by: Parikshit Pareek <quic_ppareek@quicinc.com>
Tested-by: Luca Weiss <luca.weiss@fairphone.com>
Tested-by: Steev Klimaszewski <steev@kali.org> # Thinkpad X13s
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8540p-ride
Reviewed-by: Borislav Petkov (AMD) <bp@alien8.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230314080443.64635-13-manivannan.sadhasivam@linaro.org
Stable-dep-of: cbd77119b6 ("EDAC/qcom: Get rid of hardcoded register offsets")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab1de7ead8 ]
The commit 4f7e723643 ("cgroup: Fix threadgroup_rwsem <-> cpus_read_lock()
deadlock") fixed the deadlock between cgroup_threadgroup_rwsem and
cpus_read_lock() by introducing cgroup_attach_{lock,unlock}() and removing
cpus_read_{lock,unlock}() from cpuset_attach(). But cgroup_transfer_tasks()
was missed and not handled, which will cause th following warning:
WARNING: CPU: 0 PID: 589 at kernel/cpu.c:526 lockdep_assert_cpus_held+0x32/0x40
CPU: 0 PID: 589 Comm: kworker/1:4 Not tainted 6.4.0-rc2-next-20230517 #50
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-2 04/01/2014
Workqueue: events cpuset_hotplug_workfn
RIP: 0010:lockdep_assert_cpus_held+0x32/0x40
<...>
Call Trace:
<TASK>
cpuset_attach+0x40/0x240
cgroup_migrate_execute+0x452/0x5e0
? _raw_spin_unlock_irq+0x28/0x40
cgroup_transfer_tasks+0x1f3/0x360
? find_held_lock+0x32/0x90
? cpuset_hotplug_workfn+0xc81/0xed0
cpuset_hotplug_workfn+0xcb1/0xed0
? process_one_work+0x248/0x5b0
process_one_work+0x2b9/0x5b0
worker_thread+0x56/0x3b0
? process_one_work+0x5b0/0x5b0
kthread+0xf1/0x120
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x1f/0x30
</TASK>
So just use the cgroup_attach_{lock,unlock}() helper to fix it.
Reported-by: Zhao Gongyi <zhaogongyi@bytedance.com>
Signed-off-by: Qi Zheng <zhengqi.arch@bytedance.com>
Acked-by: Muchun Song <songmuchun@bytedance.com>
Fixes: 05c7b7a92c ("cgroup/cpuset: Fix a race between cpuset_attach() and cpu hotplug")
Cc: stable@vger.kernel.org # v5.17+
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2bd1103392 ]
A successful call to cgroup_css_set_fork() will always have taken
a ref on kargs->cset (regardless of CLONE_INTO_CGROUP), so always
do a corresponding put in cgroup_css_set_put_fork().
Without this, a cset and its contained css structures will be
leaked for some fork failures. The following script reproduces
the leak for a fork failure due to exceeding pids.max in the
pids controller. A similar thing can happen if we jump to the
bad_fork_cancel_cgroup label in copy_process().
[ -z "$1" ] && echo "Usage $0 pids-root" && exit 1
PID_ROOT=$1
CGROUP=$PID_ROOT/foo
[ -e $CGROUP ] && rmdir -f $CGROUP
mkdir $CGROUP
echo 5 > $CGROUP/pids.max
echo $$ > $CGROUP/cgroup.procs
fork_bomb()
{
set -e
for i in $(seq 10); do
/bin/sleep 3600 &
done
}
(fork_bomb) &
wait
echo $$ > $PID_ROOT/cgroup.procs
kill $(cat $CGROUP/cgroup.procs)
rmdir $CGROUP
Fixes: ef2c41cf38 ("clone3: allow spawning processes into cgroups")
Cc: stable@vger.kernel.org # v5.7+
Signed-off-by: John Sperbeck <jsperbeck@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4cdb91b0de ]
Replace mutex_[un]lock() with cgroup_[un]lock() wrappers to stay
consistent across cgroup core and other subsystem code, while
operating on the cgroup_mutex.
Signed-off-by: Kamalesh Babulal <kamalesh.babulal@oracle.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Stable-dep-of: 2bd1103392 ("cgroup: always put cset in cgroup_css_set_put_fork")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a37f2699c3 ]
The call to startup_64_setup_env() will install a new GDT but does not
actually switch to using the KERNEL_CS entry until returning from the
function call.
Commit bcce829083 ("x86/sev: Detect/setup SEV/SME features earlier in
boot") moved the call to sme_enable() earlier in the boot process and in
between the call to startup_64_setup_env() and the switch to KERNEL_CS.
An SEV-ES or an SEV-SNP guest will trigger #VC exceptions during the call
to sme_enable() and if the CS pushed on the stack as part of the exception
and used by IRETQ is not mapped by the new GDT, then problems occur.
Today, the current CS when entering startup_64 is the kernel CS value
because it was set up by the decompressor code, so no issue is seen.
However, a recent patchset that looked to avoid using the legacy
decompressor during an EFI boot exposed this bug. At entry to startup_64,
the CS value is that of EFI and is not mapped in the new kernel GDT. So
when a #VC exception occurs, the CS value used by IRETQ is not valid and
the guest boot crashes.
Fix this issue by moving the block that switches to the KERNEL_CS value to
be done immediately after returning from startup_64_setup_env().
Fixes: bcce829083 ("x86/sev: Detect/setup SEV/SME features earlier in boot")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/all/6ff1f28af2829cc9aea357ebee285825f90a431f.1684340801.git.thomas.lendacky%40amd.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3918dd0177 upstream.
This driver relies on IEEE80211_CONF_PS of hw->conf.flags to turn off PS or
turn on dynamic PS controlled by driver and firmware. Though this would be
incorrect, it did work before because the flag is always recalculated until
the commit 28977e790b ("wifi: mac80211: skip powersave recalc if driver SUPPORTS_DYNAMIC_PS")
is introduced by kernel 5.20 to skip to recalculate IEEE80211_CONF_PS
of hw->conf.flags if driver sets SUPPORTS_DYNAMIC_PS.
Correct this by doing recalculation while BSS_CHANGED_PS is changed and
interface is added or removed. It is allowed to enter PS only if single
one station vif is working. Without this fix, driver doesn't enter PS
anymore that causes higher power consumption.
Fixes: bcde60e599 ("rtw88: remove misleading module parameter rtw_fw_support_lps")
Cc: stable@vger.kernel.org # 6.1+
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230527082939.11206-2-pkshih@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26a125f550 upstream.
This driver relies on IEEE80211_CONF_PS of hw->conf.flags to turn off PS or
turn on dynamic PS controlled by driver and firmware. Though this would be
incorrect, it did work before because the flag is always recalculated until
the commit 28977e790b ("wifi: mac80211: skip powersave recalc if driver SUPPORTS_DYNAMIC_PS")
is introduced by kernel 5.20 to skip to recalculate IEEE80211_CONF_PS
of hw->conf.flags if driver sets SUPPORTS_DYNAMIC_PS.
Correct this by doing recalculation while BSS_CHANGED_PS is changed and
interface is added or removed. For now, it is allowed to enter PS only if
single one station vif is working, and it could possible to have PS per
vif after firmware can support it. Without this fix, driver doesn't
enter PS anymore that causes higher power consumption.
Fixes: e3ec7017f6 ("rtw89: add Realtek 802.11ax driver")
Cc: stable@vger.kernel.org # 6.1+
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230527082939.11206-3-pkshih@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dea9d8f764 upstream.
ext4_xattr_block_set() relies on its caller to call dquot_initialize()
on the inode. To assure that this has happened there are WARN_ON
checks. Unfortunately, this is subject to false positives if there is
an antagonist thread which is flipping the file system at high rates
between r/o and rw. So only do the check if EXT4_XATTR_DEBUG is
enabled.
Link: https://lore.kernel.org/r/20230608044056.GA1418535@mit.edu
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a2ac591cb4 upstream.
Commit 06149746e7 ("Bluetooth: hci_conn: Add support for linking
multiple hcon") reintroduced a previously fixed bug [1] ("KASAN:
slab-use-after-free Read in hci_conn_hash_flush"). This bug was
originally fixed by commit 5dc7d23e16 ("Bluetooth: hci_conn: Fix
possible UAF").
The hci_conn_unlink function was added to avoid invalidating the link
traversal caused by successive hci_conn_del operations releasing extra
connections. However, currently hci_conn_unlink itself also releases
extra connections, resulted in the reintroduced bug.
This patch follows a more robust solution for cleaning up all
connections, by repeatedly removing the first connection until there are
none left. This approach does not rely on the inner workings of
hci_conn_del and ensures proper cleanup of all connections.
Meanwhile, we need to make sure that hci_conn_del never fails. Indeed it
doesn't, as it now always returns zero. To make this a bit clearer, this
patch also changes its return type to void.
Reported-by: syzbot+8bb72f86fc823817bc5d@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-bluetooth/000000000000aa920505f60d25ad@google.com/
Fixes: 06149746e7 ("Bluetooth: hci_conn: Add support for linking multiple hcon")
Signed-off-by: Ruihan Li <lrh2000@pku.edu.cn>
Co-developed-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2910431ab0 upstream.
If hci_conn_put(conn->parent) reduces conn->parent's reference count to
zero, it can immediately deallocate conn->parent. At the same time,
conn->link->list has its head in conn->parent, causing use-after-free
problems in the latter list_del_rcu(&conn->link->list).
This problem can be easily solved by reordering the two operations,
i.e., first performing the list removal with list_del_rcu and then
decreasing the refcnt with hci_conn_put.
Reported-by: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Closes: https://lore.kernel.org/linux-bluetooth/CABBYNZ+1kce8_RJrLNOXd_8=Mdpb=2bx4Nto-hFORk=qiOkoCg@mail.gmail.com/
Fixes: 06149746e7 ("Bluetooth: hci_conn: Add support for linking multiple hcon")
Signed-off-by: Ruihan Li <lrh2000@pku.edu.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 368ba06881 upstream.
The length field of netbios header must be greater than the SMB header
sizes(smb1 or smb2 header), otherwise the packet is an invalid SMB packet.
If `pdu_size` is 0, ksmbd allocates a 4 bytes chunk to `conn->request_buf`.
In the function `get_smb2_cmd_val` ksmbd will read cmd from
`rcv_hdr->Command`, which is `conn->request_buf + 12`, causing the KASAN
detector to print the following error message:
[ 7.205018] BUG: KASAN: slab-out-of-bounds in get_smb2_cmd_val+0x45/0x60
[ 7.205423] Read of size 2 at addr ffff8880062d8b50 by task ksmbd:42632/248
...
[ 7.207125] <TASK>
[ 7.209191] get_smb2_cmd_val+0x45/0x60
[ 7.209426] ksmbd_conn_enqueue_request+0x3a/0x100
[ 7.209712] ksmbd_server_process_request+0x72/0x160
[ 7.210295] ksmbd_conn_handler_loop+0x30c/0x550
[ 7.212280] kthread+0x160/0x190
[ 7.212762] ret_from_fork+0x1f/0x30
[ 7.212981] </TASK>
Cc: stable@vger.kernel.org
Reported-by: Chih-Yen Chang <cc85nod@gmail.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 25933573ef upstream.
Dan reported the following error message:
fs/smb/server/smbacl.c:1296 smb_check_perm_dacl()
error: 'posix_acls' dereferencing possible ERR_PTR()
fs/smb/server/vfs.c:1323 ksmbd_vfs_make_xattr_posix_acl()
error: 'posix_acls' dereferencing possible ERR_PTR()
fs/smb/server/vfs.c:1830 ksmbd_vfs_inherit_posix_acl()
error: 'acls' dereferencing possible ERR_PTR()
__get_acl() returns a mix of error pointers and NULL. This change it
with IS_ERR_OR_NULL().
Fixes: e2f34481b2 ("cifsd: add server-side procedures for SMB3")
Cc: stable@vger.kernel.org
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc6c6a3c32 upstream.
This bug is in parse_lease_state, and it is caused by the missing check
of `struct create_context`. When the ksmbd traverses the create_contexts,
it doesn't check if the field of `NameOffset` and `Next` is valid,
The KASAN message is following:
[ 6.664323] BUG: KASAN: slab-out-of-bounds in parse_lease_state+0x7d/0x280
[ 6.664738] Read of size 2 at addr ffff888005c08988 by task kworker/0:3/103
...
[ 6.666644] Call Trace:
[ 6.666796] <TASK>
[ 6.666933] dump_stack_lvl+0x33/0x50
[ 6.667167] print_report+0xcc/0x620
[ 6.667903] kasan_report+0xae/0xe0
[ 6.668374] kasan_check_range+0x35/0x1b0
[ 6.668621] parse_lease_state+0x7d/0x280
[ 6.668868] smb2_open+0xbe8/0x4420
[ 6.675137] handle_ksmbd_work+0x282/0x820
Use smb2_find_context_vals() to find smb2 create request lease context.
smb2_find_context_vals validate create context fields.
Cc: stable@vger.kernel.org
Reported-by: Chih-Yen Chang <cc85nod@gmail.com>
Tested-by: Chih-Yen Chang <cc85nod@gmail.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f1a411873c upstream.
The check in the beginning is
`clen + sizeof(struct smb2_neg_context) <= len_of_ctxts`,
but in the end of loop, `len_of_ctxts` will subtract
`((clen + 7) & ~0x7) + sizeof(struct smb2_neg_context)`, which causes
integer underflow when clen does the 8 alignment. We should use
`(clen + 7) & ~0x7` in the check to avoid underflow from happening.
Then there are some variables that need to be declared unsigned
instead of signed.
[ 11.671070] BUG: KASAN: slab-out-of-bounds in smb2_handle_negotiate+0x799/0x1610
[ 11.671533] Read of size 2 at addr ffff888005e86cf2 by task kworker/0:0/7
...
[ 11.673383] Call Trace:
[ 11.673541] <TASK>
[ 11.673679] dump_stack_lvl+0x33/0x50
[ 11.673913] print_report+0xcc/0x620
[ 11.674671] kasan_report+0xae/0xe0
[ 11.675171] kasan_check_range+0x35/0x1b0
[ 11.675412] smb2_handle_negotiate+0x799/0x1610
[ 11.676217] ksmbd_smb_negotiate_common+0x526/0x770
[ 11.676795] handle_ksmbd_work+0x274/0x810
...
Cc: stable@vger.kernel.org
Signed-off-by: Chih-Yen Chang <cc85nod@gmail.com>
Tested-by: Chih-Yen Chang <cc85nod@gmail.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 99a670b206 ]
On riscv qemu platform, when add kprobe event on do_sys_open() to show
filename string arg, it just print fault as follow:
echo 'p:myprobe do_sys_open dfd=$arg1 filename=+0($arg2):string flags=$arg3
mode=$arg4' > kprobe_events
bash-166 [000] ...1. 360.195367: myprobe: (do_sys_open+0x0/0x84)
dfd=0xffffffffffffff9c filename=(fault) flags=0x8241 mode=0x1b6
bash-166 [000] ...1. 360.219369: myprobe: (do_sys_open+0x0/0x84)
dfd=0xffffffffffffff9c filename=(fault) flags=0x8241 mode=0x1b6
bash-191 [000] ...1. 360.378827: myprobe: (do_sys_open+0x0/0x84)
dfd=0xffffffffffffff9c filename=(fault) flags=0x98800 mode=0x0
As riscv do not select ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE,
the +0($arg2) addr is processed as a kernel address though it is a
userspace address, cause the above filename=(fault) print. So select
ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE to avoid the issue, after that the
kprobe trace is ok as below:
bash-166 [000] ...1. 96.767641: myprobe: (do_sys_open+0x0/0x84)
dfd=0xffffffffffffff9c filename="/dev/null" flags=0x8241 mode=0x1b6
bash-166 [000] ...1. 96.793751: myprobe: (do_sys_open+0x0/0x84)
dfd=0xffffffffffffff9c filename="/dev/null" flags=0x8241 mode=0x1b6
bash-177 [000] ...1. 96.962354: myprobe: (do_sys_open+0x0/0x84)
dfd=0xffffffffffffff9c filename="/sys/kernel/debug/tracing/events/kprobes/"
flags=0x98800 mode=0x0
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Acked-by: Björn Töpel <bjorn@rivosinc.com>
Fixes: 0ebeea8ca8 ("bpf: Restrict bpf_probe_read{, str}() only to archs where they work")
Link: https://lore.kernel.org/r/20230504072910.3742842-1-ruanjinjie@huawei.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f3c782b39 ]
Selecting only REGMAP_I2C can leave REGMAP unset, causing build errors,
so also select REGMAP to prevent the build errors.
../drivers/misc/eeprom/at24.c:540:42: warning: 'struct regmap_config' declared inside parameter list will not be visible outside of this definition or declaration
540 | struct regmap_config *regmap_config)
../drivers/misc/eeprom/at24.c: In function 'at24_make_dummy_client':
../drivers/misc/eeprom/at24.c:552:18: error: implicit declaration of function 'devm_regmap_init_i2c' [-Werror=implicit-function-declaration]
552 | regmap = devm_regmap_init_i2c(dummy_client, regmap_config);
../drivers/misc/eeprom/at24.c:552:16: warning: assignment to 'struct regmap *' from 'int' makes pointer from integer without a cast [-Wint-conversion]
552 | regmap = devm_regmap_init_i2c(dummy_client, regmap_config);
../drivers/misc/eeprom/at24.c: In function 'at24_probe':
../drivers/misc/eeprom/at24.c:586:16: error: variable 'regmap_config' has initializer but incomplete type
586 | struct regmap_config regmap_config = { };
../drivers/misc/eeprom/at24.c:586:30: error: storage size of 'regmap_config' isn't known
586 | struct regmap_config regmap_config = { };
../drivers/misc/eeprom/at24.c:586:30: warning: unused variable 'regmap_config' [-Wunused-variable]
Fixes: 5c01525847 ("eeprom: at24: add basic regmap_i2c support")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6569fc12e4 ]
Commit 8aeb7b17f0 ("RISC-V: Make mmap() with PROT_WRITE imply PROT_READ")
allows riscv to use mmap with PROT_WRITE only, and meanwhile mmap with w+x
is also permitted. However, when userspace tries to access this page with
PROT_WRITE|PROT_EXEC, which causes infinite loop at load page fault as
well as it triggers soft lockup. According to riscv privileged spec,
"Writable pages must also be marked readable". The fix to drop the
`PAGE_COPY_READ_EXEC` and then `PAGE_COPY_EXEC` would be just used instead.
This aligns the other arches (i.e arm64) for protection_map.
Fixes: 8aeb7b17f0 ("RISC-V: Make mmap() with PROT_WRITE imply PROT_READ")
Signed-off-by: Hsieh-Tseng Shen <woodrow.shen@sifive.com>
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Link: https://lore.kernel.org/r/20230425102828.1616812-1-woodrow.shen@sifive.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca0aa17f2d ]
If pm runtime resume fails the .remove callback used to exit early. This
resulted in an error message by the driver core but the device gets
removed anyhow. This lets the registered i2c adapter stay around with an
unbound parent device.
So only skip clk disabling if resume failed, but do delete the adapter.
Fixes: 8b9ec07198 ("i2c: Add Spreadtrum I2C controller driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95ae9979bf ]
When constructing the sim, gpio-sim constructs an array of named lines,
sized based on the largest offset of any named line, and then initializes
that array with the names of all lines, including unnamed hogs with higher
offsets. In doing so it writes NULLs beyond the extent of the array.
Add a check that only named lines are used to initialize the array.
Fixes: cb8c474e79 ("gpio: sim: new testing module")
Signed-off-by: Kent Gibson<warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5578d0a79b ]
There seems to be a bug within the mv64xxx I2C controller, wherein the
status register may not necessarily contain valid value immediately
after the IFLG flag is set in the control register.
My theory is that the controller:
- first sets the IFLG in control register
- then updates the status register
- then raises an interrupt
This may sometime cause weird bugs when in atomic mode, since in this
mode we do not wait for an interrupt, but instead we poll the control
register for IFLG and read status register immediately after.
I encountered -ENXIO from mv64xxx_i2c_fsm() due to this issue when using
this driver in atomic mode.
Note that I've only seen this issue on Armada 385, I don't know whether
other SOCs with this controller are also affected. Also note that this
fix has been in U-Boot for over 4 years [1] without anybody complaining,
so it should not cause regressions.
[1] https://source.denx.de/u-boot/u-boot/-/commit/d50e29662f78
Fixes: 544a8d75f3 ("i2c: mv64xxx: Add atomic_xfer method to driver")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9bf2e53431 ]
The final production baseboard had a different chip select than
earlier prototype boards. When the newer board was released,
the SPI stopped working because the wrong pin was used in the device
tree and conflicted with the UART RTS. Fix the pinmux for
production boards.
Fixes: 36ca3c8ccb ("arm64: dts: imx: Add Beacon i.MX8M Nano development kit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ddad59331a ]
The nr_active counter continues to increase over time which causes the
blk_mq_get_tag to hang until the thread is rescheduled to a different
core despite there are still tags available.
kernel-stack
INFO: task inboundIOReacto:3014879 blocked for more than 2 seconds
Not tainted 6.1.15-amd64 #1 Debian 6.1.15~debian11
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:inboundIOReacto state:D stack:0 pid:3014879 ppid:4557 flags:0x00000000
Call Trace:
<TASK>
__schedule+0x351/0xa20
scheduler+0x5d/0xe0
io_schedule+0x42/0x70
blk_mq_get_tag+0x11a/0x2a0
? dequeue_task_stop+0x70/0x70
__blk_mq_alloc_requests+0x191/0x2e0
kprobe output showing RQF_MQ_INFLIGHT bit is not cleared before
__blk_mq_free_request being called.
320 320 kworker/29:1H __blk_mq_free_request rq_flags 0x220c0 in-flight 1
b'__blk_mq_free_request+0x1 [kernel]'
b'bt_iter+0x50 [kernel]'
b'blk_mq_queue_tag_busy_iter+0x318 [kernel]'
b'blk_mq_timeout_work+0x7c [kernel]'
b'process_one_work+0x1c4 [kernel]'
b'worker_thread+0x4d [kernel]'
b'kthread+0xe6 [kernel]'
b'ret_from_fork+0x1f [kernel]'
Signed-off-by: Tian Lan <tian.lan@twosigma.com>
Fixes: 2e315dc07d ("blk-mq: grab rq->refcount before calling ->fn in blk_mq_tagset_busy_iter")
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230513221227.497327-1-tilan7663@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 635071f5fe ]
The code in asoc_simple_startup was treating any non-zero return from
snd_pcm_hw_constraint_minmax as an error, when this can return 1 in some
normal cases and only negative values indicate an error.
When this happened, it caused asoc_simple_startup to disable the clocks
it just enabled and return 1, which was not treated as an error by the
calling code which only checks for negative return values. Then when the
PCM is eventually shut down, it causes the clock framework to complain
about disabling clocks that were not enabled.
Fix the check for snd_pcm_hw_constraint_minmax return value to only
treat negative values as an error.
Fixes: 5ca2ab4598 ("ASoC: simple-card-utils: Add new system-clock-fixed flag")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20230602011936.231931-1-robert.hancock@calian.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc93f0dcb4 ]
During mt8195_afe_init_clock(), mt8195_audsys_clk_register() was called
followed by several other devm functions. At mt8195_afe_deinit_clock()
located at mt8195_afe_pcm_dev_remove(), mt8195_audsys_clk_unregister()
was called.
However, there was an issue with the order in which these functions were
called. Specifically, the remove callback of platform_driver was called
before devres released the resource, resulting in a use-after-free issue
during remove time.
At probe time, the order of calls was:
1. mt8195_audsys_clk_register
2. afe_priv->clk = devm_kcalloc
3. afe_priv->clk[i] = devm_clk_get
At remove time, the order of calls was:
1. mt8195_audsys_clk_unregister
3. free afe_priv->clk[i]
2. free afe_priv->clk
To resolve the problem, we can utilize devm_add_action_or_reset() in
mt8195_audsys_clk_register() so that the remove order can be changed to
3->2->1.
Fixes: 6746cc8582 ("ASoC: mediatek: mt8195: add platform driver")
Signed-off-by: Trevor Wu <trevor.wu@mediatek.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230601033318.10408-3-trevor.wu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6461fee680 ]
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20230315150745.67084-114-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: dc93f0dcb4 ("ASoC: mediatek: mt8195: fix use-after-free in driver remove path")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd67a7a1a2 ]
During mt8188_afe_init_clock(), mt8188_audsys_clk_register() was called
followed by several other devm functions. The caller of
mt8188_afe_init_clock() utilized devm_add_action_or_reset() to call
mt8188_afe_deinit_clock(). However, the order was incorrect, causing a
use-after-free issue during remove time.
At probe time, the order of calls was:
1. mt8188_audsys_clk_register
2. afe_priv->clk = devm_kcalloc
3. afe_priv->clk[i] = devm_clk_get
At remove time, the order of calls was:
1. mt8188_audsys_clk_unregister
3. free afe_priv->clk[i]
2. free afe_priv->clk
To resolve the problem, it's necessary to move devm_add_action_or_reset()
to the appropriate position so that the remove order can be 3->2->1.
Fixes: f6b026479b ("ASoC: mediatek: mt8188: support audio clock control")
Signed-off-by: Trevor Wu <trevor.wu@mediatek.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230601033318.10408-2-trevor.wu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6b5c6426e ]
Sending the mutex address(acp_lock) as platform
data during ACP PDM platform driver register sequence,
its creating copy of the platform data.
Referencing this platform data in ACP PDM driver results
incorrect reference to the common lock usage.
Instead of directly passing the lock address as platform
data, retrieve it from parent driver data structure
and use the same lock reference in ACP PDM driver.
Fixes: 45aa83cb93 ("ASoC: amd: ps: use acp_lock to protect common registers in pdm driver")
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230525113000.1290758-1-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca50d77655 ]
Add the assigned-clocks and assigned-clock-rates properties for the
LPUARTx nodes. Without these properties, the default clock rate
used would be 0, which can cause the UART ports to fail when open.
Fixes: 35f4e9d753 ("arm64: dts: imx8: split adma ss into dma and audio ss")
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a735530c1 ]
In general, the three SKUs of sc7180 (lite, normal, and pro) are
handled dynamically.
The cpufreq table in sc7180.dtsi includes the superset of all CPU
frequencies. The "qcom-cpufreq-hw" driver in Linux shows that we can
dynamically detect which frequencies are actually available on the
currently running CPU and then we can just enable those ones.
The GPU is similarly dynamic. The nvmem has a fuse in it (see
"gpu_speed_bin" in sc7180.dtsi) that the GPU driver can use to figure
out which frequencies to enable.
There is one part, however, that is not so dynamic. The way SDRAM
frequency works in sc7180 is that it's tied to cpufreq. At the busiest
cpufreq operating points we'll pick the top supported SDRAM frequency.
They ramp down together.
For the "pro" SKU of sc7180, we only enable one extra cpufreq step.
That extra cpufreq step runs SDRAM at the same speed as the step
below. Thus, for normal and pro things are OK. There is no sc7180-pro
device tree snippet.
For the "lite" SKU if sc7180, however, things aren't so easy. The
"lite" SKU drops 3 cpufreq entries but can still run SDRAM at max
frequency. That messed things up with the whole scheme. This is why we
added the "sc7180-lite" fragment in commit 8fd01e01fd ("arm64: dts:
qcom: sc7180-lite: Tweak DDR/L3 scaling on SC7180-lite").
When the lite scheme came about, it was agreed that the WiFi SKUs of
lazor would _always_ be "lite" and would, in fact, be the only "lite"
devices. Unfortunately, this decision changed and folks didn't realize
that it would be a problem. Specifically, some later lazor WiFi-only
devices were built with "pro" CPUs.
Building WiFi-only lazor with "pro" CPUs isn't the end of the world.
The SDRAM will ramp up a little sooner than it otherwise would, but
aside from a small power hit things work OK. One problem, though, is
that the SDRAM scaling becomes a bit quirky. Specifically, with the
current tables we'll max out SDRAM frequency at 2.1GHz but then
_lower_ it at 2.2GHz / 2.3GHz only to raise it back to max for 2.4GHz
and 2.55GHz.
Let's at least fix this so that the SDRAM frequency doesn't go down in
that quirky way. On true "lite" SKUs this change will be a no-op
because the operating points we're touching are disabled. This change
is only useful when a board that thinks it has a "lite" CPU actually
has a "normal" or "pro" one stuffed.
Fixes: 8fd01e01fd ("arm64: dts: qcom: sc7180-lite: Tweak DDR/L3 scaling on SC7180-lite")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230515171929.1.Ic8dee2cb79ce39ffc04eab2a344dde47b2f9459f@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ccd4923d18 ]
The of_find_device_by_node() function is returning a struct platform_device
object with the embedded struct device member's reference counter
incremented. This needs to be dropped when done with the platform device
returned by of_find_device_by_node().
at91_pm_eth_quirk_is_valid() calls of_find_device_by_node() on
suspend and resume path. On suspend it calls of_find_device_by_node() and
on resume and failure paths it drops the counter of
struct platform_device::dev.
In case ethernet device may not wakeup there is a put_device() on
at91_pm_eth_quirk_is_valid() which is wrong as it colides with
put_device() on resume path leading to the reference counter of struct
device embedded in struct platform_device to be messed, stack trace to be
displayed (after 5 consecutive suspend/resume cycles) and execution to
hang.
Along with this the error path of at91_pm_config_quirks() had been also
adapted to decrement propertly the reference counter of struct device
embedded in struct platform_device.
Fixes: b7fc72c633 ("ARM: at91: pm: add quirks for pm")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20230518062511.2988500-1-claudiu.beznea@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 81a31a860b upstream.
Without EXCLUSIVE_SYSTEM_RAM, users are allowed to map arbitrary
physical memory regions into the userspace via /dev/mem. At the same
time, pages may change their properties (e.g., from anonymous pages to
named pages) while they are still being mapped in the userspace, leading
to "corruption" detected by the page table check.
To avoid these false positives, this patch makes PAGE_TABLE_CHECK
depends on EXCLUSIVE_SYSTEM_RAM. This dependency is understandable
because PAGE_TABLE_CHECK is a hardening technique but /dev/mem without
STRICT_DEVMEM (i.e., !EXCLUSIVE_SYSTEM_RAM) is itself a security
problem.
Even with EXCLUSIVE_SYSTEM_RAM, I/O pages may be still allowed to be
mapped via /dev/mem. However, these pages are always considered as named
pages, so they won't break the logic used in the page table check.
Cc: <stable@vger.kernel.org> # 5.17
Signed-off-by: Ruihan Li <lrh2000@pku.edu.cn>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Pasha Tatashin <pasha.tatashin@soleen.com>
Link: https://lore.kernel.org/r/20230515130958.32471-4-lrh2000@pku.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0b861653f upstream.
When hcd->localmem_pool is non-null, localmem_pool is used to allocate
DMA memory. In this case, the dma address will be properly returned (in
dma_handle), and dma_mmap_coherent should be used to map this memory
into the user space. However, the current implementation uses
pfn_remap_range, which is supposed to map normal pages.
Instead of repeating the logic in the memory allocation function, this
patch introduces a more robust solution. Here, the type of allocated
memory is checked by testing whether dma_handle is properly set. If
dma_handle is properly returned, it means some DMA pages are allocated
and dma_mmap_coherent should be used to map them. Otherwise, normal
pages are allocated and pfn_remap_range should be called. This ensures
that the correct mmap functions are used consistently, independently
with logic details that determine which type of memory gets allocated.
Fixes: a0e710a7de ("USB: usbfs: fix mmap dma mismatch")
Cc: stable@vger.kernel.org
Signed-off-by: Ruihan Li <lrh2000@pku.edu.cn>
Link: https://lore.kernel.org/r/20230515130958.32471-3-lrh2000@pku.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0143d148d1 upstream.
The current implementation of usbdev_mmap uses usb_alloc_coherent to
allocate memory pages that will later be mapped into the user space.
Meanwhile, usb_alloc_coherent employs three different methods to
allocate memory, as outlined below:
* If hcd->localmem_pool is non-null, it uses gen_pool_dma_alloc to
allocate memory;
* If DMA is not available, it uses kmalloc to allocate memory;
* Otherwise, it uses dma_alloc_coherent.
However, it should be noted that gen_pool_dma_alloc does not guarantee
that the resulting memory will be page-aligned. Furthermore, trying to
map slab pages (i.e., memory allocated by kmalloc) into the user space
is not resonable and can lead to problems, such as a type confusion bug
when PAGE_TABLE_CHECK=y [1].
To address these issues, this patch introduces hcd_alloc_coherent_pages,
which addresses the above two problems. Specifically,
hcd_alloc_coherent_pages uses gen_pool_dma_alloc_align instead of
gen_pool_dma_alloc to ensure that the memory is page-aligned. To replace
kmalloc, hcd_alloc_coherent_pages directly allocates pages by calling
__get_free_pages.
Reported-by: syzbot+fcf1a817ceb50935ce99@syzkaller.appspotmail.comm
Closes: https://lore.kernel.org/lkml/000000000000258e5e05fae79fc1@google.com/ [1]
Fixes: f7d34b445a ("USB: Add support for usbfs zerocopy.")
Fixes: ff2437befd ("usb: host: Fix excessive alignment restriction for local memory allocations")
Cc: stable@vger.kernel.org
Signed-off-by: Ruihan Li <lrh2000@pku.edu.cn>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20230515130958.32471-2-lrh2000@pku.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 870611e487 upstream.
Move capturing the snapshot context into the image request state
machine, after exclusive lock is ensured to be held for the duration of
dealing with the image request. This is needed to ensure correctness
of fast-diff states (OBJECT_EXISTS vs OBJECT_EXISTS_CLEAN) and object
deltas computed based off of them. Otherwise the object map that is
forked for the snapshot isn't guaranteed to accurately reflect the
contents of the snapshot when the snapshot is taken under I/O. This
breaks differential backup and snapshot-based mirroring use cases with
fast-diff enabled: since some object deltas may be incomplete, the
destination image may get corrupted.
Cc: stable@vger.kernel.org
Link: https://tracker.ceph.com/issues/61472
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Dongsheng Yang <dongsheng.yang@easystack.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09fe05c57b upstream.
Move RBD_OBJ_FLAG_COPYUP_ENABLED flag setting into the object request
state machine to allow for the snapshot context to be captured in the
image request state machine rather than in rbd_queue_workfn().
Cc: stable@vger.kernel.org
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Dongsheng Yang <dongsheng.yang@easystack.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 436eeae041 upstream.
After TEE has completed processing of TEE_CMD_ID_LOAD_TA, set proper
value in 'return_origin' argument passed by open_session() call. To do
so, add 'return_origin' field to the structure tee_cmd_load_ta. The
Trusted OS shall update return_origin as part of TEE processing.
This change to 'struct tee_cmd_load_ta' interface requires a similar update
in AMD-TEE Trusted OS's TEE_CMD_ID_LOAD_TA interface.
This patch has been verified on Phoenix Birman setup. On older APUs,
return_origin value will be 0.
Cc: stable@vger.kernel.org
Fixes: 757cc3e9ff ("tee: add AMD-TEE driver")
Tested-by: Sourabh Das <sourabh.das@amd.com>
Signed-off-by: Rijo Thomas <Rijo-john.Thomas@amd.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47c5d829a3 upstream.
Since commit 3e4be65eb8 ("Bluetooth: hci_qca: Add poweroff support
during hci down for wcn3990"), the setup callback which registers the
debugfs interface can be called multiple times.
This specifically leads to the following error when powering on the
controller:
debugfs: Directory 'ibs' with parent 'hci0' already present!
Add a driver flag to avoid trying to register the debugfs interface more
than once.
Fixes: 3e4be65eb8 ("Bluetooth: hci_qca: Add poweroff support during hci down for wcn3990")
Cc: stable@vger.kernel.org # 4.20
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe2ccc6c29 upstream.
Since commit ec6cef9cd9 ("Bluetooth: Fix SMP channel registration for
unconfigured controllers") the debugfs interface for unconfigured
controllers will be created when the controller is configured.
There is however currently nothing preventing a controller from being
configured multiple time (e.g. setting the device address using btmgmt)
which results in failed attempts to register the already registered
debugfs entries:
debugfs: File 'features' in directory 'hci0' already present!
debugfs: File 'manufacturer' in directory 'hci0' already present!
debugfs: File 'hci_version' in directory 'hci0' already present!
...
debugfs: File 'quirk_simultaneous_discovery' in directory 'hci0' already present!
Add a controller flag to avoid trying to register the debugfs interface
more than once.
Fixes: ec6cef9cd9 ("Bluetooth: Fix SMP channel registration for unconfigured controllers")
Cc: stable@vger.kernel.org # 4.0
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ccc45cb4e7 upstream.
The lock around counting the channel queue length in the BIODASDINFO
ioctl was incorrectly changed to the dasd_block->queue_lock with commit
583d6535cb ("dasd: remove dead code"). This can lead to endless list
iterations and a subsequent crash.
The queue_lock is supposed to be used only for queue lists belonging to
dasd_block. For dasd_device related queue lists the ccwdev lock must be
used.
Fix the mentioned issues by correctly using the ccwdev lock instead of
the queue lock.
Fixes: 583d6535cb ("dasd: remove dead code")
Cc: stable@vger.kernel.org # v5.0+
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://lore.kernel.org/r/20230609153750.1258763-2-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 409e873ea3 upstream.
There is a race between capsnaps flush and removing the inode from
'mdsc->snap_flush_list' list:
== Thread A == == Thread B ==
ceph_queue_cap_snap()
-> allocate 'capsnapA'
->ihold('&ci->vfs_inode')
->add 'capsnapA' to 'ci->i_cap_snaps'
->add 'ci' to 'mdsc->snap_flush_list'
...
== Thread C ==
ceph_flush_snaps()
->__ceph_flush_snaps()
->__send_flush_snap()
handle_cap_flushsnap_ack()
->iput('&ci->vfs_inode')
this also will release 'ci'
...
== Thread D ==
ceph_handle_snap()
->flush_snaps()
->iterate 'mdsc->snap_flush_list'
->get the stale 'ci'
->remove 'ci' from ->ihold(&ci->vfs_inode) this
'mdsc->snap_flush_list' will WARNING
To fix this we will increase the inode's i_count ref when adding 'ci'
to the 'mdsc->snap_flush_list' list.
[ idryomov: need_put int -> bool ]
Cc: stable@vger.kernel.org
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2209299
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Milind Changire <mchangir@redhat.com>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 48d73f609d upstream.
This patch is linked to the previous commit ("mptcp: only send RM_ADDR in
nl_cmd_remove").
To align with what is done by the in-kernel PM, update userspace pm addr
selftests, by sending a remove_subflows command together after the
remove_addrs command.
Fixes: d9a4594eda ("mptcp: netlink: Add MPTCP_PM_CMD_REMOVE")
Fixes: 97040cf980 ("selftests: mptcp: userspace pm address tests")
Cc: stable@vger.kernel.org
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77e4b94a3d upstream.
Increase pm subflows counter on both server side and client side when
userspace pm creates a new subflow, and decrease the counter when it
closes a subflow.
Increase add_addr_signaled counter in mptcp_nl_cmd_announce() when the
address is announced by userspace PM.
This modification is similar to how the in-kernel PM is updating the
counter: when additional subflows are created/removed.
Fixes: 9ab4807c84 ("mptcp: netlink: Add MPTCP_PM_CMD_ANNOUNCE")
Fixes: 702c2f646d ("mptcp: netlink: allow userspace-driven subflow establishment")
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/329
Cc: stable@vger.kernel.org
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 24430f8bf5 upstream.
Add the address into userspace_pm_local_addr_list when the subflow is
created. Make sure it can be found in mptcp_nl_cmd_remove(). And delete
it in the new helper mptcp_userspace_pm_delete_local_addr().
By doing this, the "REMOVE" command also works with subflows that have
been created via the "SUB_CREATE" command instead of restricting to
the addresses that have been announced via the "ANNOUNCE" command.
Fixes: d9a4594eda ("mptcp: netlink: Add MPTCP_PM_CMD_REMOVE")
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/379
Cc: stable@vger.kernel.org
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd9c790de2 upstream.
It turns out access to j1939_can_rx_register() needs to be serialized,
otherwise j1939_priv can be corrupted when parallel threads call
j1939_netdev_start() and j1939_can_rx_register() fails. This issue is
thoroughly covered in other commit which serializes access to
j1939_can_rx_register().
Change j1939_netdev_lock type to mutex so that we do not need to remove
GFP_KERNEL from can_rx_register().
j1939_netdev_lock seems to be used in normal contexts where mutex usage
is not prohibited.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: 9d71dd0c70 ("can: add support of SAE J1939 protocol")
Suggested-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20230526171910.227615-2-pchelkin@ispras.ru
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a84aea80e upstream.
This patch addresses an issue within the j1939_sk_send_loop_abort()
function in the j1939/socket.c file, specifically in the context of
Transport Protocol (TP) sessions.
Without this patch, when a TP session is initiated and a Clear To Send
(CTS) frame is received from the remote side requesting one data packet,
the kernel dispatches the first Data Transport (DT) frame and then waits
for the next CTS. If the remote side doesn't respond with another CTS,
the kernel aborts due to a timeout. This leads to the user-space
receiving an EPOLLERR on the socket, and the socket becomes active.
However, when trying to read the error queue from the socket with
sock.recvmsg(, , socket.MSG_ERRQUEUE), it returns -EAGAIN,
given that the socket is non-blocking. This situation results in an
infinite loop: the user-space repeatedly calls epoll(), epoll() returns
the socket file descriptor with EPOLLERR, but the socket then blocks on
the recv() of ERRQUEUE.
This patch introduces an additional check for the J1939_SOCK_ERRQUEUE
flag within the j1939_sk_send_loop_abort() function. If the flag is set,
it indicates that the application has subscribed to receive error queue
messages. In such cases, the kernel can communicate the current transfer
state via the error queue. This allows for the function to return early,
preventing the unnecessary setting of the socket into an error state,
and breaking the infinite loop. It is crucial to note that a socket
error is only needed if the application isn't using the error queue, as,
without it, the application wouldn't be aware of transfer issues.
Fixes: 9d71dd0c70 ("can: add support of SAE J1939 protocol")
Reported-by: David Jander <david@protonic.nl>
Tested-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20230526081946.715190-1-o.rempel@pengutronix.de
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a4615b9a9 upstream.
kmemdup() at line 2735 is not duplicating enough memory for
notif->tid_tear_down and notif->station_id. As it only duplicates
612 bytes: up to offsetofend(struct iwl_wowlan_info_notif,
received_beacons), this is the range of [0, 612) bytes.
2735 notif = kmemdup(notif_v1,
2736 offsetofend(struct iwl_wowlan_info_notif,
2737 received_beacons),
2738 GFP_ATOMIC);
which evidently does not cover bytes 612 and 613 for members
tid_tear_down and station_id in struct iwl_wowlan_info_notif.
See below:
$ pahole -C iwl_wowlan_info_notif drivers/net/wireless/intel/iwlwifi/mvm/d3.o
struct iwl_wowlan_info_notif {
struct iwl_wowlan_gtk_status_v3 gtk[2]; /* 0 488 */
/* --- cacheline 7 boundary (448 bytes) was 40 bytes ago --- */
struct iwl_wowlan_igtk_status igtk[2]; /* 488 80 */
/* --- cacheline 8 boundary (512 bytes) was 56 bytes ago --- */
__le64 replay_ctr; /* 568 8 */
/* --- cacheline 9 boundary (576 bytes) --- */
__le16 pattern_number; /* 576 2 */
__le16 reserved1; /* 578 2 */
__le16 qos_seq_ctr[8]; /* 580 16 */
__le32 wakeup_reasons; /* 596 4 */
__le32 num_of_gtk_rekeys; /* 600 4 */
__le32 transmitted_ndps; /* 604 4 */
__le32 received_beacons; /* 608 4 */
u8 tid_tear_down; /* 612 1 */
u8 station_id; /* 613 1 */
u8 reserved2[2]; /* 614 2 */
/* size: 616, cachelines: 10, members: 13 */
/* last cacheline: 40 bytes */
};
Therefore, when the following assignments take place, actually no memory
has been allocated for those objects:
2743 notif->tid_tear_down = notif_v1->tid_tear_down;
2744 notif->station_id = notif_v1->station_id;
Fix this by allocating space for the whole notif object and zero out the
remaining space in memory after member station_id.
This also fixes the following -Warray-bounds issues:
CC drivers/net/wireless/intel/iwlwifi/mvm/d3.o
drivers/net/wireless/intel/iwlwifi/mvm/d3.c: In function ‘iwl_mvm_wait_d3_notif’:
drivers/net/wireless/intel/iwlwifi/mvm/d3.c:2743:30: warning: array subscript ‘struct iwl_wowlan_info_notif[0]’ is partly outside array bounds of ‘unsigned char[612]’ [-Warray-bounds=]
2743 | notif->tid_tear_down = notif_v1->tid_tear_down;
|
from drivers/net/wireless/intel/iwlwifi/mvm/d3.c:7:
In function ‘kmemdup’,
inlined from ‘iwl_mvm_wait_d3_notif’ at drivers/net/wireless/intel/iwlwifi/mvm/d3.c:2735:12:
include/linux/fortify-string.h:765:16: note: object of size 612 allocated by ‘__real_kmemdup’
765 | return __real_kmemdup(p, size, gfp);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/intel/iwlwifi/mvm/d3.c: In function ‘iwl_mvm_wait_d3_notif’:
drivers/net/wireless/intel/iwlwifi/mvm/d3.c:2744:30: warning: array subscript ‘struct iwl_wowlan_info_notif[0]’ is partly outside array bounds of ‘unsigned char[612]’ [-Warray-bounds=]
2744 | notif->station_id = notif_v1->station_id;
| ^~
In function ‘kmemdup’,
inlined from ‘iwl_mvm_wait_d3_notif’ at drivers/net/wireless/intel/iwlwifi/mvm/d3.c:2735:12:
include/linux/fortify-string.h:765:16: note: object of size 612 allocated by ‘__real_kmemdup’
765 | return __real_kmemdup(p, size, gfp);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~
Link: https://github.com/KSPP/linux/issues/306
Fixes: 905d50ddbc ("wifi: iwlwifi: mvm: support wowlan info notification version 2")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Acked-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/ZHpGN555FwAKGduH@work
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 59de751e38 upstream.
[Why]
When going from ODM 2:1 single display case to max displays, second
odm pipe needs to be repurposed for one of the new single displays.
However, acquire_first_split_pipe() only handles MPC case and not
ODM case
[How]
Add ODM conditions in acquire_first_split_pipe()
Add commit_minimal_transition_state() in commit_streams() to handle
odm 2:1 exit first, and then process new streams
Handle ODM condition in commit_minimal_transition_state()
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Samson Tam <samson.tam@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 30c3d3b70a upstream.
commit cf488dcd0a ("drm/amd: Allow s0ix without BIOS support") showed
improvements to power consumption over suspend when s0ix wasn't enabled in
BIOS and the system didn't support S3.
This patch however was misguided because the reason the system didn't
support S3 was because SMT was disabled in OEM BIOS setup.
This prevented the BIOS from allowing S3.
Also allowing GPUs to use the s2idle path actually causes problems if
they're invoked on systems that may not support s2idle in the platform
firmware. `systemd` has a tendency to try to use `s2idle` if `deep` fails
for any reason, which could lead to unexpected flows.
The original commit also fixed a problem during resume from suspend to idle
without hardware support, but this is no longer necessary with commit
ca47518663 ("drm/amd: Don't allow s0ix on APUs older than Raven")
Revert commit cf488dcd0a ("drm/amd: Allow s0ix without BIOS support")
to make it match the expected behavior again.
Cc: Rafael Ávila de Espíndola <rafael@espindo.la>
Link: https://github.com/torvalds/linux/blob/v6.1/drivers/gpu/drm/amd/amdgpu/amdgpu_acpi.c#L1060
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/2599
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit feee70f456 upstream.
While doing my research to improve the xpad device names I noticed
that the 1532:0037 VID/PID seems to be used by the DeathAdder 2013,
so that Razer Sabertooth instance looked wrong and very suspect to
me. I didn't see any mention in the official drivers, either.
After doing more research, it turns out that the xpad list
is used by many other projects (like Steam) as-is [1], this
issue was reported [2] and Valve/Sam Lantinga fixed it [3]:
[1]: dcc5eef0e2/src/joystick/controller_type.h (L251)
[2]: https://steamcommunity.com/app/353380/discussions/0/1743392486228754770/
[3]: https://hg.libsdl.org/SDL/rev/29809f6f0271
(With multiple Internet users reporting similar issues, not linked here)
After not being able to find the correct VID/PID combination anywhere
on the Internet and not receiving any reply from Razer support I did
some additional detective work, it seems like it presents itself as
"Razer Sabertooth Gaming Controller (XBOX360)", code 1689:FE00.
Leaving us with this:
* Razer Sabertooth (1689:fe00)
* Razer Sabertooth Elite (24c6:5d04)
* Razer DeathAdder 2013 (1532:0037) [note: not a gamepad]
So, to sum things up; remove this conflicting/duplicate entry:
{ 0x1532, 0x0037, "Razer Sabertooth", 0, XTYPE_XBOX360 },
As the real/correct one is already present there, even if
the Internet as a whole insists on presenting it as the
Razer Sabertooth Elite, which (by all accounts) is not:
{ 0x1689, 0xfe00, "Razer Sabertooth", 0, XTYPE_XBOX360 },
Actual change in SDL2 referencing this kernel issue:
e5e5416975
For more information of the device, take a look here:
https://github.com/xboxdrv/xboxdrv/pull/59
You can see a lsusb dump here: https://github.com/xboxdrv/xboxdrv/files/76581/Qa6dBcrv.txt
Fixes: f554f619b7 ("Input: xpad - sync device IDs with xboxdrv")
Signed-off-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Reviewed-by: Cameron Gutman <aicommander@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/5c12dbdb-5774-fc68-5c58-ca596383663e@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit abac3ac97f upstream.
Syzkaller got a lot of crashes like:
KASAN: use-after-free Write in *_timers*
All of these crashes point to the same memory area:
The buggy address belongs to the object at ffff88801f870000
which belongs to the cache kmalloc-8k of size 8192
The buggy address is located 5320 bytes inside of
8192-byte region [ffff88801f870000, ffff88801f872000)
This area belongs to :
batadv_priv->batadv_priv_dat->delayed_work->timer_list
The reason for these issues is the lack of synchronization. Delayed
work (batadv_dat_purge) schedules new timer/work while the device
is being deleted. As the result new timer/delayed work is set after
cancel_delayed_work_sync() was called. So after the device is freed
the timer list contains pointer to already freed memory.
Found by Linux Verification Center (linuxtesting.org) with syzkaller.
Cc: stable@kernel.org
Fixes: 2f1dfbe185 ("batman-adv: Distributed ARP Table - implement local storage")
Signed-off-by: Vladislav Efanov <VEfanov@ispras.ru>
Acked-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1eb4ef1259 ]
As per the new udp tunnel framework, drivers which need to know the
details of a port entry (i.e. port type) when it gets deleted should
use the .set_port / .unset_port callbacks.
Implementing the current .udp_tunnel_sync callback would mean that the
deleted tunnel port entry would be all zeros. This used to work on
older firmware because it would not check the input when deleting a
tunnel port. With newer firmware, the delete will now fail and
subsequent tunnel port allocation will fail as a result.
Fixes: 442a35a5a7 ("bnxt: convert to new udp_tunnel_nic infra")
Reviewed-by: Kalesh Anakkur Purayil <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 319a7827df ]
The firmware can send PHC_RTC_UPDATE async event on a PF that may not
have PTP registered. In such a case, there will be a null pointer
deference for bp->ptp_cfg when we try to handle the event.
Fix it by not registering for this event with the firmware if !bp->ptp_cfg.
Also, check that bp->ptp_cfg is valid before proceeding when we receive
the event.
Fixes: 8bcf6f04d4 ("bnxt_en: Handle async event when the PHC is updated in RTC mode")
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83474a9b25 ]
Driver starts firmware fatal error recovery by detecting
heartbeat failure or fw reset count register changing. But
these checks are not reliable if the device is not accessible.
This can happen while DPC (Downstream Port containment) is in
progress. Skip firmware fatal recovery if pci_device_is_present()
returns false.
Fixes: acfb50e4e7 ("bnxt_en: Add FW fatal devlink_health_reporter.")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a9e4f501b ]
We need to call bnxt_hwrm_func_qcfg() on a VF to query the default
VLAN that may be setup by the PF. If a default VLAN is enabled,
the VF cannot support VLAN acceleration on the receive side and
the VNIC must be setup to strip out the default VLAN tag. If a
default VLAN is not enabled, the VF can support VLAN acceleration
on the receive side. The VNIC should be set up to strip or not
strip the VLAN based on the RX VLAN acceleration setting.
Without this call to determine the default VLAN before calling
bnxt_setup_vnic(), the VNIC may not be set up correctly. For
example, bnxt_setup_vnic() may set up to strip the VLAN tag based
on stale default VLAN information. If RX VLAN acceleration is
not enabled, the VLAN tag will be incorrectly stripped and the
RX data path will not work correctly.
Fixes: cf6645f8eb ("bnxt_en: Add function for VF driver to query default VLAN.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d997801c7 ]
Only older NIC controller's firmware uses the PROC AP reset type.
Firmware on 5731X/5741X and newer chips does not support this reset
type. When bnxt_reset() issues a series of resets, this PROC AP
reset may actually fail on these newer chips because the firmware
is not ready to accept this unsupported command yet. Avoid this
unnecessary error by skipping this reset type on chips that don't
support it.
Fixes: 7a13240e37 ("bnxt_en: fix ethtool_reset_flags ABI violations")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9f31047ba ]
We had a number of short comings:
- EEE must be re-evaluated whenever the state machine detects a link
change as wight be switching from a link partner with EEE
enabled/disabled
- tx_lpi_enabled controls whether EEE should be enabled/disabled for the
transmit path, which applies to the TBUF block
- We do not need to forcibly enable EEE upon system resume, as the PHY
state machine will trigger a link event that will do that, too
Fixes: 6ef398ea60 ("net: bcmgenet: add EEE support")
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20230606214348.2408018-1-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a1eb1a343 ]
Use the function of amdgpu_bo_vm_destroy to handle the resource release
of shadow bo. During the amdgpu_mes_self_test, shadow bo released, but
vmbo->shadow_list was not, which caused a null pointer reference error
in amdgpu_device_recover_vram when GPU reset.
Fixes: 6c032c37ac ("drm/amdgpu: Fix vram recover doesn't work after whole GPU reset (v2)")
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Signed-off-by: Horatio Zhang <Hongkun.Zhang@amd.com>
Acked-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f46fab0e36 ]
Anastasios reported crash on stable 5.15 kernel with following
BPF attached to lsm hook:
SEC("lsm.s/bprm_creds_for_exec")
int BPF_PROG(bprm_creds_for_exec, struct linux_binprm *bprm)
{
struct path *path = &bprm->executable->f_path;
char p[128] = { 0 };
bpf_d_path(path, p, 128);
return 0;
}
But bprm->executable can be NULL, so bpf_d_path call will crash:
BUG: kernel NULL pointer dereference, address: 0000000000000018
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC NOPTI
...
RIP: 0010:d_path+0x22/0x280
...
Call Trace:
<TASK>
bpf_d_path+0x21/0x60
bpf_prog_db9cf176e84498d9_bprm_creds_for_exec+0x94/0x99
bpf_trampoline_6442506293_0+0x55/0x1000
bpf_lsm_bprm_creds_for_exec+0x5/0x10
security_bprm_creds_for_exec+0x29/0x40
bprm_execve+0x1c1/0x900
do_execveat_common.isra.0+0x1af/0x260
__x64_sys_execve+0x32/0x40
It's problem for all stable trees with bpf_d_path helper, which was
added in 5.9.
This issue is fixed in current bpf code, where we identify and mark
trusted pointers, so the above code would fail even to load.
For the sake of the stable trees and to workaround potentially broken
verifier in the future, adding the code that reads the path object from
the passed pointer and verifies it's valid in kernel space.
Fixes: 6e22ab9da7 ("bpf: Add d_path helper")
Reported-by: Anastasios Papagiannis <tasos.papagiannnis@gmail.com>
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20230606181714.532998-1-jolsa@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44f8baaf23 ]
try_module_get will be called in tcf_proto_lookup_ops. So module_put needs
to be called to drop the refcount if ops don't implement the required
function.
Fixes: 9f407f1768 ("net: sched: introduce chain templates")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 682881ee45 ]
Fixes following sparse errors:
net/sched/act_police.c:360:28: warning: dereference of noderef expression
net/sched/act_police.c:362:45: warning: dereference of noderef expression
net/sched/act_police.c:362:45: warning: dereference of noderef expression
net/sched/act_police.c:368:28: warning: dereference of noderef expression
net/sched/act_police.c:370:45: warning: dereference of noderef expression
net/sched/act_police.c:370:45: warning: dereference of noderef expression
net/sched/act_police.c:376:45: warning: dereference of noderef expression
net/sched/act_police.c:376:45: warning: dereference of noderef expression
Fixes: d1967e495a ("net_sched: act_police: add 2 new attributes to support police 64bit rate and peakrate")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de9df6c6b2 ]
Currently, the per cpu upcall counters are allocated after the vport is
created and inserted into the system. This could lead to the datapath
accessing the counters before they are allocated resulting in a kernel
Oops.
Here is an example:
PID: 59693 TASK: ffff0005f4f51500 CPU: 0 COMMAND: "ovs-vswitchd"
#0 [ffff80000a39b5b0] __switch_to at ffffb70f0629f2f4
#1 [ffff80000a39b5d0] __schedule at ffffb70f0629f5cc
#2 [ffff80000a39b650] preempt_schedule_common at ffffb70f0629fa60
#3 [ffff80000a39b670] dynamic_might_resched at ffffb70f0629fb58
#4 [ffff80000a39b680] mutex_lock_killable at ffffb70f062a1388
#5 [ffff80000a39b6a0] pcpu_alloc at ffffb70f0594460c
#6 [ffff80000a39b750] __alloc_percpu_gfp at ffffb70f05944e68
#7 [ffff80000a39b760] ovs_vport_cmd_new at ffffb70ee6961b90 [openvswitch]
...
PID: 58682 TASK: ffff0005b2f0bf00 CPU: 0 COMMAND: "kworker/0:3"
#0 [ffff80000a5d2f40] machine_kexec at ffffb70f056a0758
#1 [ffff80000a5d2f70] __crash_kexec at ffffb70f057e2994
#2 [ffff80000a5d3100] crash_kexec at ffffb70f057e2ad8
#3 [ffff80000a5d3120] die at ffffb70f0628234c
#4 [ffff80000a5d31e0] die_kernel_fault at ffffb70f062828a8
#5 [ffff80000a5d3210] __do_kernel_fault at ffffb70f056a31f4
#6 [ffff80000a5d3240] do_bad_area at ffffb70f056a32a4
#7 [ffff80000a5d3260] do_translation_fault at ffffb70f062a9710
#8 [ffff80000a5d3270] do_mem_abort at ffffb70f056a2f74
#9 [ffff80000a5d32a0] el1_abort at ffffb70f06297dac
#10 [ffff80000a5d32d0] el1h_64_sync_handler at ffffb70f06299b24
#11 [ffff80000a5d3410] el1h_64_sync at ffffb70f056812dc
#12 [ffff80000a5d3430] ovs_dp_upcall at ffffb70ee6963c84 [openvswitch]
#13 [ffff80000a5d3470] ovs_dp_process_packet at ffffb70ee6963fdc [openvswitch]
#14 [ffff80000a5d34f0] ovs_vport_receive at ffffb70ee6972c78 [openvswitch]
#15 [ffff80000a5d36f0] netdev_port_receive at ffffb70ee6973948 [openvswitch]
#16 [ffff80000a5d3720] netdev_frame_hook at ffffb70ee6973a28 [openvswitch]
#17 [ffff80000a5d3730] __netif_receive_skb_core.constprop.0 at ffffb70f06079f90
We moved the per cpu upcall counter allocation to the existing vport
alloc and free functions to solve this.
Fixes: 95637d91fe ("net: openvswitch: release vport resources on failure")
Fixes: 1933ea365a ("net: openvswitch: Add support to count upcall packets")
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 886bc7d6ed ]
rtm_tca_policy is used from net/sched/sch_api.c and net/sched/cls_api.c,
thus should be declared in an include file.
This fixes the following sparse warning:
net/sched/sch_api.c:1434:25: warning: symbol 'rtm_tca_policy' was not declared. Should it be static?
Fixes: e331473fee ("net/sched: cls_api: add missing validation of netlink attributes")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf15bb38ec ]
The current ice driver's GNSS write implementation buffers writes and
works through them asynchronously in a kthread. That's bad because:
- The GNSS write_raw operation is supposed to be synchronous[1][2].
- There is no upper bound on the number of pending writes.
Userspace can submit writes much faster than the driver can process,
consuming unlimited amounts of kernel memory.
A patch that's currently on review[3] ("[v3,net] ice: Write all GNSS
buffers instead of first one") would add one more problem:
- The possibility of waiting for a very long time to flush the write
work when doing rmmod, softlockups.
To fix these issues, simplify the implementation: Drop the buffering,
the write_work, and make the writes synchronous.
I tested this with gpsd and ubxtool.
[1] https://events19.linuxfoundation.org/wp-content/uploads/2017/12/The-GNSS-Subsystem-Johan-Hovold-Hovold-Consulting-AB.pdf
"User interface" slide.
[2] A comment in drivers/gnss/core.c:gnss_write():
/* Ignoring O_NONBLOCK, write_raw() is synchronous. */
[3] https://patchwork.ozlabs.org/project/intel-wired-lan/patch/20230217120541.16745-1-karol.kolacinski@intel.com/
Fixes: d6b98c8d24 ("ice: add write functionality for GNSS TTY")
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c3b74a92a ]
Add READ_ONCE()/WRITE_ONCE() on accesses to the sock flow table.
This also prevents a (smart ?) compiler to remove the condition in:
if (table->ents[index] != newval)
table->ents[index] = newval;
We need the condition to avoid dirtying a shared cache line.
Fixes: fec5e652e5 ("rfs: Receive Flow Steering")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e5c647c3f ]
Add READ_ONCE()/WRITE_ONCE() on accesses to sk->sk_rxhash.
This also prevents a (smart ?) compiler to remove the condition in:
if (sk->sk_rxhash != newval)
sk->sk_rxhash = newval;
We need the condition to avoid dirtying a shared cache line.
Fixes: fec5e652e5 ("rfs: Receive Flow Steering")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 82a01ab35b ]
We missed that tcp_gso_segment() was assuming skb->len was smaller than 65535 :
oldlen = (u16)~skb->len;
This part came with commit 0718bcc09b ("[NET]: Fix CHECKSUM_HW GSO problems.")
This leads to wrong TCP checksum.
Adapt the code to accept arbitrary packet length.
v2:
- use two csum_add() instead of csum_fold() (Alexander Duyck)
- Change delta type to __wsum to reduce casts (Alexander Duyck)
Fixes: 09f3d1a3a5 ("ipv6/gso: remove temporary HBH/jumbo header")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230605161647.3624428-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2f4c143d7 ]
A remote DoS vulnerability of RPL Source Routing is assigned CVE-2023-2156.
The Source Routing Header (SRH) has the following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Next Header | Hdr Ext Len | Routing Type | Segments Left |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| CmprI | CmprE | Pad | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
. .
. Addresses[1..n] .
. .
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The originator of an SRH places the first hop's IPv6 address in the IPv6
header's IPv6 Destination Address and the second hop's IPv6 address as
the first address in Addresses[1..n].
The CmprI and CmprE fields indicate the number of prefix octets that are
shared with the IPv6 Destination Address. When CmprI or CmprE is not 0,
Addresses[1..n] are compressed as follows:
1..n-1 : (16 - CmprI) bytes
n : (16 - CmprE) bytes
Segments Left indicates the number of route segments remaining. When the
value is not zero, the SRH is forwarded to the next hop. Its address
is extracted from Addresses[n - Segment Left + 1] and swapped with IPv6
Destination Address.
When Segment Left is greater than or equal to 2, the size of SRH is not
changed because Addresses[1..n-1] are decompressed and recompressed with
CmprI.
OTOH, when Segment Left changes from 1 to 0, the new SRH could have a
different size because Addresses[1..n-1] are decompressed with CmprI and
recompressed with CmprE.
Let's say CmprI is 15 and CmprE is 0. When we receive SRH with Segment
Left >= 2, Addresses[1..n-1] have 1 byte for each, and Addresses[n] has
16 bytes. When Segment Left is 1, Addresses[1..n-1] is decompressed to
16 bytes and not recompressed. Finally, the new SRH will need more room
in the header, and the size is (16 - 1) * (n - 1) bytes.
Here the max value of n is 255 as Segment Left is u8, so in the worst case,
we have to allocate 3825 bytes in the skb headroom. However, now we only
allocate a small fixed buffer that is IPV6_RPL_SRH_WORST_SWAP_SIZE (16 + 7
bytes). If the decompressed size overflows the room, skb_push() hits BUG()
below [0].
Instead of allocating the fixed buffer for every packet, let's allocate
enough headroom only when we receive SRH with Segment Left 1.
[0]:
skbuff: skb_under_panic: text:ffffffff81c9f6e2 len:576 put:576 head:ffff8880070b5180 data:ffff8880070b4fb0 tail:0x70 end:0x140 dev:lo
kernel BUG at net/core/skbuff.c:200!
invalid opcode: 0000 [#1] PREEMPT SMP PTI
CPU: 0 PID: 154 Comm: python3 Not tainted 6.4.0-rc4-00190-gc308e9ec0047 #7
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
RIP: 0010:skb_panic (net/core/skbuff.c:200)
Code: 4f 70 50 8b 87 bc 00 00 00 50 8b 87 b8 00 00 00 50 ff b7 c8 00 00 00 4c 8b 8f c0 00 00 00 48 c7 c7 80 6e 77 82 e8 ad 8b 60 ff <0f> 0b 66 66 2e 0f 1f 84 00 00 00 00 00 90 90 90 90 90 90 90 90 90
RSP: 0018:ffffc90000003da0 EFLAGS: 00000246
RAX: 0000000000000085 RBX: ffff8880058a6600 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffff88807dc1c540 RDI: ffff88807dc1c540
RBP: ffffc90000003e48 R08: ffffffff82b392c8 R09: 00000000ffffdfff
R10: ffffffff82a592e0 R11: ffffffff82b092e0 R12: ffff888005b1c800
R13: ffff8880070b51b8 R14: ffff888005b1ca18 R15: ffff8880070b5190
FS: 00007f4539f0b740(0000) GS:ffff88807dc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055670baf3000 CR3: 0000000005b0e000 CR4: 00000000007506f0
PKRU: 55555554
Call Trace:
<IRQ>
skb_push (net/core/skbuff.c:210)
ipv6_rthdr_rcv (./include/linux/skbuff.h:2880 net/ipv6/exthdrs.c:634 net/ipv6/exthdrs.c:718)
ip6_protocol_deliver_rcu (net/ipv6/ip6_input.c:437 (discriminator 5))
ip6_input_finish (./include/linux/rcupdate.h:805 net/ipv6/ip6_input.c:483)
__netif_receive_skb_one_core (net/core/dev.c:5494)
process_backlog (./include/linux/rcupdate.h:805 net/core/dev.c:5934)
__napi_poll (net/core/dev.c:6496)
net_rx_action (net/core/dev.c:6565 net/core/dev.c:6696)
__do_softirq (./arch/x86/include/asm/jump_label.h:27 ./include/linux/jump_label.h:207 ./include/trace/events/irq.h:142 kernel/softirq.c:572)
do_softirq (kernel/softirq.c:472 kernel/softirq.c:459)
</IRQ>
<TASK>
__local_bh_enable_ip (kernel/softirq.c:396)
__dev_queue_xmit (net/core/dev.c:4272)
ip6_finish_output2 (./include/net/neighbour.h:544 net/ipv6/ip6_output.c:134)
rawv6_sendmsg (./include/net/dst.h:458 ./include/linux/netfilter.h:303 net/ipv6/raw.c:656 net/ipv6/raw.c:914)
sock_sendmsg (net/socket.c:724 net/socket.c:747)
__sys_sendto (net/socket.c:2144)
__x64_sys_sendto (net/socket.c:2156 net/socket.c:2152 net/socket.c:2152)
do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120)
RIP: 0033:0x7f453a138aea
Code: d8 64 89 02 48 c7 c0 ff ff ff ff eb b8 0f 1f 00 f3 0f 1e fa 41 89 ca 64 8b 04 25 18 00 00 00 85 c0 75 15 b8 2c 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 7e c3 0f 1f 44 00 00 41 54 48 83 ec 30 44 89
RSP: 002b:00007ffcc212a1c8 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 00007ffcc212a288 RCX: 00007f453a138aea
RDX: 0000000000000060 RSI: 00007f4539084c20 RDI: 0000000000000003
RBP: 00007f4538308e80 R08: 00007ffcc212a300 R09: 000000000000001c
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: ffffffffc4653600 R14: 0000000000000001 R15: 00007f4539712d1b
</TASK>
Modules linked in:
Fixes: 8610c7c6e3 ("net: ipv6: add support for rpl sr exthdr")
Reported-by: Max VA
Closes: https://www.interruptlabs.co.uk/articles/linux-ipv6-route-of-death
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230605180617.67284-1-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6eea63c709 ]
The drm sched entity must be flushed before finishing, to account for
jobs potentially still in flight at that time.
Lima did not do this flush until now, so switch the destroy call to the
drm_sched_entity_destroy() wrapper which will take care of that.
This fixes a regression on lima which started since the rework in
commit 2fdb8a8f07 ("drm/scheduler: rework entity flush, kill and fini")
where some specific types of applications may hang indefinitely.
Fixes: 2fdb8a8f07 ("drm/scheduler: rework entity flush, kill and fini")
Reviewed-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Erico Nunes <nunes.erico@gmail.com>
Signed-off-by: Qiang Yu <yuq825@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230606143247.433018-1-nunes.erico@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24e227896b ]
syzkaller found a repro that causes Hung Task [0] with ipset. The repro
first creates an ipset and then tries to delete a large number of IPs
from the ipset concurrently:
IPSET_ATTR_IPADDR_IPV4 : 172.20.20.187
IPSET_ATTR_CIDR : 2
The first deleting thread hogs a CPU with nfnl_lock(NFNL_SUBSYS_IPSET)
held, and other threads wait for it to be released.
Previously, the same issue existed in set->variant->uadt() that could run
so long under ip_set_lock(set). Commit 5e29dc36bd ("netfilter: ipset:
Rework long task execution when adding/deleting entries") tried to fix it,
but the issue still exists in the caller with another mutex.
While adding/deleting many IPs, we should release the CPU periodically to
prevent someone from abusing ipset to hang the system.
Note we need to increment the ipset's refcnt to prevent the ipset from
being destroyed while rescheduling.
[0]:
INFO: task syz-executor174:268 blocked for more than 143 seconds.
Not tainted 6.4.0-rc1-00145-gba79e9a73284 #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:syz-executor174 state:D stack:0 pid:268 ppid:260 flags:0x0000000d
Call trace:
__switch_to+0x308/0x714 arch/arm64/kernel/process.c:556
context_switch kernel/sched/core.c:5343 [inline]
__schedule+0xd84/0x1648 kernel/sched/core.c:6669
schedule+0xf0/0x214 kernel/sched/core.c:6745
schedule_preempt_disabled+0x58/0xf0 kernel/sched/core.c:6804
__mutex_lock_common kernel/locking/mutex.c:679 [inline]
__mutex_lock+0x6fc/0xdb0 kernel/locking/mutex.c:747
__mutex_lock_slowpath+0x14/0x20 kernel/locking/mutex.c:1035
mutex_lock+0x98/0xf0 kernel/locking/mutex.c:286
nfnl_lock net/netfilter/nfnetlink.c:98 [inline]
nfnetlink_rcv_msg+0x480/0x70c net/netfilter/nfnetlink.c:295
netlink_rcv_skb+0x1c0/0x350 net/netlink/af_netlink.c:2546
nfnetlink_rcv+0x18c/0x199c net/netfilter/nfnetlink.c:658
netlink_unicast_kernel net/netlink/af_netlink.c:1339 [inline]
netlink_unicast+0x664/0x8cc net/netlink/af_netlink.c:1365
netlink_sendmsg+0x6d0/0xa4c net/netlink/af_netlink.c:1913
sock_sendmsg_nosec net/socket.c:724 [inline]
sock_sendmsg net/socket.c:747 [inline]
____sys_sendmsg+0x4b8/0x810 net/socket.c:2503
___sys_sendmsg net/socket.c:2557 [inline]
__sys_sendmsg+0x1f8/0x2a4 net/socket.c:2586
__do_sys_sendmsg net/socket.c:2595 [inline]
__se_sys_sendmsg net/socket.c:2593 [inline]
__arm64_sys_sendmsg+0x80/0x94 net/socket.c:2593
__invoke_syscall arch/arm64/kernel/syscall.c:38 [inline]
invoke_syscall+0x84/0x270 arch/arm64/kernel/syscall.c:52
el0_svc_common+0x134/0x24c arch/arm64/kernel/syscall.c:142
do_el0_svc+0x64/0x198 arch/arm64/kernel/syscall.c:193
el0_svc+0x2c/0x7c arch/arm64/kernel/entry-common.c:637
el0t_64_sync_handler+0x84/0xf0 arch/arm64/kernel/entry-common.c:655
el0t_64_sync+0x190/0x194 arch/arm64/kernel/entry.S:591
Reported-by: syzkaller <syzkaller@googlegroups.com>
Fixes: a7b4f989a6 ("netfilter: ipset: IP set core support")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Acked-by: Jozsef Kadlecsik <kadlec@netfilter.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1f543dc66 ]
An nf_conntrack_helper from nf_conn_help may become NULL after DNAT.
Observed when TCP port 1720 (Q931_PORT), associated with h323 conntrack
helper, is DNAT'ed to another destination port (e.g. 1730), while
nfqueue is being used for final acceptance (e.g. snort).
This happenned after transition from kernel 4.14 to 5.10.161.
Workarounds:
* keep the same port (1720) in DNAT
* disable nfqueue
* disable/unload h323 NAT helper
$ linux-5.10/scripts/decode_stacktrace.sh vmlinux < /tmp/kernel.log
BUG: kernel NULL pointer dereference, address: 0000000000000084
[..]
RIP: 0010:nf_conntrack_update (net/netfilter/nf_conntrack_core.c:2080 net/netfilter/nf_conntrack_core.c:2134) nf_conntrack
[..]
nfqnl_reinject (net/netfilter/nfnetlink_queue.c:237) nfnetlink_queue
nfqnl_recv_verdict (net/netfilter/nfnetlink_queue.c:1230) nfnetlink_queue
nfnetlink_rcv_msg (net/netfilter/nfnetlink.c:241) nfnetlink
[..]
Fixes: ee04805ff5 ("netfilter: conntrack: make conntrack userspace helpers work again")
Signed-off-by: Tijs Van Buggenhout <tijs.van.buggenhout@axsguard.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14e8b29390 ]
At the end of `nft_bitwise_reduce`, there is a loop which is intended to
update the bitwise expression associated with each tracked destination
register. However, currently, it just updates the first register
repeatedly. Fix it.
Fixes: 34cc9e5288 ("netfilter: nf_tables: cancel tracking for clobbered destination registers")
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd058763a6 ]
The nla_nest_start_noflag() function may fail and return NULL;
the return value needs to be checked.
Found by InfoTeCS on behalf of Linux Verification Center
(linuxtesting.org) with SVACE.
Fixes: d54725cd11 ("netfilter: nf_tables: support for multiple devices per netdev hook")
Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e54ed8247 ]
This should use wiphy_lock() now instead of acquiring the
RTNL, since cfg80211_stop_sched_scan_req() now needs that.
Fixes: a05829a722 ("cfg80211: avoid holding the RTNL when calling the driver")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68c228557d ]
There were two bugs when creating the non-inheritence
element:
1) 'at_extension' needs to be declared outside the loop,
otherwise the value resets every iteration and we
can never really switch properly
2) 'added' never got set to true, so we always cut off
the extension element again at the end of the function
This shows another issue that we might add a list but no
extension list, but we need to make the extension list a
zero-length one in that case.
Fix all these issues. While at it, add a comment explaining
the trim.
Fixes: 81151ce462 ("wifi: mac80211: support MLO authentication/association with one link")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230604120651.3addaa5c4782.If3a78f9305997ad7ef4ba7ffc17a8234c956f613@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75767213f3 ]
When receiving a connect response we should make sure that the DCID is
within the valid range and that we don't already have another channel
allocated for the same DCID.
Missing checks may violate the specification (BLUETOOTH CORE SPECIFICATION
Version 5.4 | Vol 3, Part A, Page 1046).
Fixes: 40624183c2 ("Bluetooth: L2CAP: Add missing checks for invalid LE DCID")
Signed-off-by: Sungwoo Kim <iam@sung-woo.kim>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71e9588435 ]
The order of CIS handle array in Set CIG Parameters response shall match
the order of the CIS_ID array in the command (Core v5.3 Vol 4 Part E Sec
7.8.97). We send CIS_IDs mainly in the order of increasing CIS_ID (but
with "last" CIS first if it has fixed CIG_ID). In handling of the
reply, we currently assume this is also the same as the order of
hci_conn in hdev->conn_hash, but that is not true.
Match the correct hci_conn to the correct handle by matching them based
on the CIG+CIS combination. The CIG+CIS combination shall be unique for
ISO_LINK hci_conn at state >= BT_BOUND, which we maintain in
hci_le_set_cig_params.
Fixes: 26afbd826e ("Bluetooth: Add initial implementation of CIS connections")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c14516faed ]
This fixes only matching CIS by address which prevents creating new hcon
if upper layer is requesting a specific CIS ID.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Stable-dep-of: 71e9588435 ("Bluetooth: ISO: use correct CIS order in Set CIG Parameters event")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06149746e7 ]
Since it is required for some configurations to have multiple CIS with
the same peer which is now covered by iso-tester in the following test
cases:
ISO AC 6(i) - Success
ISO AC 7(i) - Success
ISO AC 8(i) - Success
ISO AC 9(i) - Success
ISO AC 11(i) - Success
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Stable-dep-of: 71e9588435 ("Bluetooth: ISO: use correct CIS order in Set CIG Parameters event")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c242c64a0 ]
Consider existing BOUND & CONNECT state CIS to block CIG removal.
Otherwise, under suitable timing conditions we may attempt to remove CIG
while Create CIS is pending, which fails.
Fixes: 26afbd826e ("Bluetooth: Add initial implementation of CIS connections")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02c5ea5246 ]
L2CAP assumes that the locks conn->chan_lock and chan->lock are
acquired in the order conn->chan_lock, chan->lock to avoid
potential deadlock.
For example, l2sock_shutdown acquires these locks in the order:
mutex_lock(&conn->chan_lock)
l2cap_chan_lock(chan)
However, l2cap_disconnect_req acquires chan->lock in
l2cap_get_chan_by_scid first and then acquires conn->chan_lock
before calling l2cap_chan_del. This means that these locks are
acquired in unexpected order, which leads to potential deadlock:
l2cap_chan_lock(c)
mutex_lock(&conn->chan_lock)
This patch releases chan->lock before acquiring the conn_chan_lock
to avoid the potential deadlock.
Fixes: a2a9339e1c ("Bluetooth: L2CAP: Fix use-after-free in l2cap_disconnect_{req,rsp}")
Signed-off-by: Ying Hsu <yinghsu@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1857c19941 ]
When the HCI_UNREGISTER flag is set, no jobs should be scheduled. Fix
potential race when HCI_UNREGISTER is set after the flag is tested in
hci_cmd_sync_queue.
Fixes: 0b94f2651f ("Bluetooth: hci_sync: Fix queuing commands when HCI_UNREGISTER is set")
Signed-off-by: Zhengping Jiang <jiangzp@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6a7a46b86 ]
Make CIG auto-allocation to select the first CIG_ID that is still
configurable. Also use correct CIG_ID range (see Core v5.3 Vol 4 Part E
Sec 7.8.97 p.2553).
Previously, it would always select CIG_ID 0 regardless of anything,
because cis_list with data.cis == 0xff (BT_ISO_QOS_CIS_UNSET) would not
count any CIS. Since we are not adding CIS here, use find_cis instead.
Fixes: 26afbd826e ("Bluetooth: Add initial implementation of CIS connections")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31c5f91649 ]
When looking for CIS blocking CIG removal, consider only the CIS with
the right CIG ID. Don't try to remove CIG with unset CIG ID.
Fixes: 26afbd826e ("Bluetooth: Add initial implementation of CIS connections")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0fe8c8d071 ]
Split bt_iso_qos into dedicated unicast and broadcast
structures and add additional broadcast parameters.
Fixes: eca0ae4aea ("Bluetooth: Add initial implementation of BIS connections")
Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Stable-dep-of: 31c5f91649 ("Bluetooth: ISO: consider right CIS when removing CIG at cleanup")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fdebd850cc ]
The rx_bytes statistics of XDP are always zero, because rx_byte_cnt
is not updated after it is initialized to 0. So fix it.
Fixes: d1b15102dd ("net: enetc: add support for XDP_DROP and XDP_PASS")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7190d0ff0e ]
The rx_bytes of struct net_device_stats should count the length of
ethernet frames excluding the FCS. However, there are two problems
with the rx_bytes statistics of the current enetc driver. one is
that the length of VLAN header is not counted if the VLAN extraction
feature is enabled. The other is that the length of L2 header is not
counted, because eth_type_trans() is invoked before updating rx_bytes
which will subtract the length of L2 header from skb->len.
BTW, the rx_bytes statistics of XDP path also have similar problem,
I will fix it in another patch.
Fixes: a800abd3ec ("net: enetc: move skb creation into enetc_build_skb")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c308e9ec00 ]
SMCRv1 has a similar issue to SMCRv2 (see link below) that may access
invalid MRs of RMBs when construct LLC ADD LINK CONT messages.
BUG: kernel NULL pointer dereference, address: 0000000000000014
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 5 PID: 48 Comm: kworker/5:0 Kdump: loaded Tainted: G W E 6.4.0-rc3+ #49
Workqueue: events smc_llc_add_link_work [smc]
RIP: 0010:smc_llc_add_link_cont+0x160/0x270 [smc]
RSP: 0018:ffffa737801d3d50 EFLAGS: 00010286
RAX: ffff964f82144000 RBX: ffffa737801d3dd8 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff964f81370c30
RBP: ffffa737801d3dd4 R08: ffff964f81370000 R09: ffffa737801d3db0
R10: 0000000000000001 R11: 0000000000000060 R12: ffff964f82e70000
R13: ffff964f81370c38 R14: ffffa737801d3dd3 R15: 0000000000000001
FS: 0000000000000000(0000) GS:ffff9652bfd40000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000014 CR3: 000000008fa20004 CR4: 00000000003706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
smc_llc_srv_rkey_exchange+0xa7/0x190 [smc]
smc_llc_srv_add_link+0x3ae/0x5a0 [smc]
smc_llc_add_link_work+0xb8/0x140 [smc]
process_one_work+0x1e5/0x3f0
worker_thread+0x4d/0x2f0
? __pfx_worker_thread+0x10/0x10
kthread+0xe5/0x120
? __pfx_kthread+0x10/0x10
ret_from_fork+0x2c/0x50
</TASK>
When an alernate RNIC is available in system, SMC will try to add a new
link based on the RNIC for resilience. All the RMBs in use will be mapped
to the new link. Then the RMBs' MRs corresponding to the new link will
be filled into LLC messages. For SMCRv1, they are ADD LINK CONT messages.
However smc_llc_add_link_cont() may mistakenly access to unused RMBs which
haven't been mapped to the new link and have no valid MRs, thus causing a
crash. So this patch fixes it.
Fixes: 87f88cda21 ("net/smc: rkey processing for a new link as SMC client")
Link: https://lore.kernel.org/r/1685101741-74826-3-git-send-email-guwen@linux.alibaba.com
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit edf2e1d201 ]
skip_notify_on_dev_down ctl table expects this field
to be an int (4 bytes), not a bool (1 byte).
Because proc_dou8vec_minmax() was added in 5.13,
this patch converts skip_notify_on_dev_down to an int.
Following patch then converts the field to u8 and use proc_dou8vec_minmax().
Fixes: 7c6bb7d2fa ("net/ipv6: Add knob to skip DELROUTE message on device down")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cba41bb78d ]
Commit d937bc3449 ("bpf: make uniform use of array->elem_size
everywhere in arraymap.c") changed array_map_gen_lookup to use
array->elem_size instead of round_up(map->value_size, 8) as the element
size when generating code to access a value in an array map.
array->elem_size, however, is not set by bpf_map_meta_alloc when
initializing an BPF_MAP_TYPE_ARRAY_OF_MAPS or BPF_MAP_TYPE_HASH_OF_MAPS.
This results in array_map_gen_lookup incorrectly outputting code that
always accesses index 0 in the array (as the index will be calculated
via a multiplication with the element size, which is incorrectly set to
0).
Set elem_size on the bpf_array object when allocating an array or hash
of maps to fix this.
Fixes: d937bc3449 ("bpf: make uniform use of array->elem_size everywhere in arraymap.c")
Signed-off-by: Rhys Rustad-Elliott <me@rhysre.net>
Link: https://lore.kernel.org/r/20230602190110.47068-2-me@rhysre.net
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0fd1852bc ]
When task local storage was generalized for tracing programs, the
bpf_task_local_storage callback was moved from a BPF LSM hook
callback for security_task_free LSM hook to it's own callback. But a
failure case in bad_fork_cleanup_security was missed which, when
triggered, led to a dangling task owner pointer and a subsequent
use-after-free. Move the bpf_task_storage_free to the very end of
free_task to handle all failure cases.
This issue was noticed when a BPF LSM program was attached to the
task_alloc hook on a kernel with KASAN enabled. The program used
bpf_task_storage_get to copy the task local storage from the current
task to the new task being created.
Fixes: a10787e6d5 ("bpf: Enable task local storage for tracing programs")
Reported-by: Kuba Piecuch <jpiecuch@google.com>
Signed-off-by: KP Singh <kpsingh@kernel.org>
Acked-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230602002612.1117381-1-kpsingh@kernel.org
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e209fee411 ]
With this commit, all the GIDs ("0 4294967294") can be written to the
"net.ipv4.ping_group_range" sysctl.
Note that 4294967295 (0xffffffff) is an invalid GID (see gid_valid() in
include/linux/uidgid.h), and an attempt to register this number will cause
-EINVAL.
Prior to this commit, only up to GID 2147483647 could be covered.
Documentation/networking/ip-sysctl.rst had "0 4294967295" as an example
value, but this example was wrong and causing -EINVAL.
Fixes: c319b4d76b ("net: ipv4: add IPPROTO_ICMP socket kind")
Co-developed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Akihiro Suda <akihiro.suda.cz@hco.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed779fe4c9 ]
After the blamed commit, the member key is longer 4-byte aligned. On
platforms that do not support unaligned access, e.g., MIPS32R2 with
unaligned_action set to 1, this will trigger a crash when accessing
an IPv6 pneigh_entry, as the key is cast to an in6_addr pointer.
Change the type of the key to u32 to make it aligned.
Fixes: 62dd93181a ("[IPV6] NDISC: Set per-entry is_router flag in Proxy NA.")
Signed-off-by: Qingfang DENG <qingfang.deng@siflower.com.cn>
Link: https://lore.kernel.org/r/20230601015432.159066-1-dqfext@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a27648c742 ]
kafs incorrectly passes a zero mtime (ie. 1st Jan 1970) to the server when
creating a file, dir or symlink because the mtime recorded in the
afs_operation struct gets passed to the server by the marshalling routines,
but the afs_mkdir(), afs_create() and afs_symlink() functions don't set it.
This gets masked if a file or directory is subsequently modified.
Fix this by filling in op->mtime before calling the create op.
Fixes: e49c7b2f6d ("afs: Build an abstraction around an "operation" concept")
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeffrey Altman <jaltman@auristor.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c331fd1dc ]
It is usually better to request all necessary resources (clocks,
regulators, ...) before starting to make use of them. That way they do
not change state in case one of the resources is not available yet and
probe deferral (-EPROBE_DEFER) is necessary. This is particularly
important for DMA channels and IOMMUs which are not enforced by
fw_devlink yet (unless you use fw_devlink.strict=1).
spi-qup does this in the wrong order, the clocks are enabled and
disabled again when the DMA channels are not available yet.
This causes issues in some cases: On most SoCs one of the SPI QUP
clocks is shared with the UART controller. When using earlycon UART is
actively used during boot but might not have probed yet, usually for
the same reason (waiting for the DMA controller). In this case, the
brief enable/disable cycle ends up gating the clock and further UART
console output will halt the system completely.
Avoid this by requesting the DMA channels before changing the clock
state.
Fixes: 612762e82a ("spi: qup: Add DMA capabilities")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20230518-spi-qup-clk-defer-v1-1-f49fc9ca4e02@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9bed667033 ]
Devices with a type-cover have an additional "book" mode, deactivating
type-cover input and turning off its backlight. This is currently
unsupported, leading to the warning
surface_aggregator_tablet_mode_switch 01:0e:01:00:01: unknown KIP cover state: 6
Therefore, add support for this state and map it to enable tablet-mode.
Fixes: 9f794056db ("platform/surface: Add KIP/POS tablet-mode switch driver")
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20230525213218.2797480-2-luzmaximilian@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 539e0a7f91 ]
Currently, event completion work-items are restricted to be run strictly
in non-parallel fashion by the respective workqueue. However, this has
lead to some problems:
In some instances, the event notifier function called inside this
completion workqueue takes a non-negligible amount of time to execute.
One such example is the battery event handling code (surface_battery.c),
which can result in a full battery information refresh, involving
further synchronous communication with the EC inside the event handler.
This is made worse if the communication fails spuriously, generally
incurring a multi-second timeout.
Since the event completions are run strictly non-parallel, this blocks
other events from being propagated to the respective subsystems. This
becomes especially noticeable for keyboard and touchpad input, which
also funnel their events through this system. Here, users have reported
occasional multi-second "freezes".
Note, however, that the event handling system was never intended to run
purely sequentially. Instead, we have one work struct per EC/SAM
subsystem, processing the event queue for that subsystem. These work
structs were intended to run in parallel, allowing sequential processing
of work items for each subsystem but parallel processing of work items
across subsystems.
The only restriction to this is the way the workqueue is created.
Therefore, replace create_workqueue() with alloc_workqueue() and do not
restrict the maximum number of parallel work items to be executed on
that queue, resolving any cross-subsystem blockage.
Fixes: c167b9c7e3 ("platform/surface: Add Surface Aggregator subsystem")
Link: https://github.com/linux-surface/linux-surface/issues/1026
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20230525210110.2785470-1-luzmaximilian@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit eb1f822c76 upstream.
In commit a44be64bbe ("ext4: don't clear SB_RDONLY when remounting
r/w until quota is re-enabled") we defer clearing tyhe SB_RDONLY flag
in struct super. However, we didn't defer when we checked sb_rdonly()
to determine the lazy itable init thread should be enabled, with the
next result that the lazy inode table initialization would not be
properly started. This can cause generic/231 to fail in ext4's
nojournal mode.
Fix this by moving when we decide to start or stop the lazy itable
init thread to after we clear the SB_RDONLY flag when we are
remounting the file system read/write.
Fixes a44be64bbe ("ext4: don't clear SB_RDONLY when remounting r/w until...")
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Link: https://lore.kernel.org/r/20230527035729.1001605-1-tytso@mit.edu
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is for linux-6.3.y only, it has no direct mainline
equivalent.
LLVM 17 will now use the GOT for extern weak symbols when using the
medany model, which causes a linker orphan section warning on
linux-6.3.y:
ld.lld: warning: <internal>:(.got) is being placed in '.got'
This is not an issue in mainline because handling of the .got section
was added by commit 39b3307294 ("riscv: Introduce CONFIG_RELOCATABLE")
and further extended by commit 26e7aacb83 ("riscv: Allow to downgrade
paging mode from the command line") in 6.4-rc1. Neither of these changes
are suitable for stable, so add explicit handling of the .got section in
a standalone change to align 6.3 and mainline, which addresses the
warning.
This is only an issue for 6.3 because commit f4b71bff8d ("riscv:
select ARCH_WANT_LD_ORPHAN_WARN for !XIP_KERNEL") landed in 6.3-rc1, so
earlier releases will not see this warning because it will not be
enabled.
Closes: https://github.com/ClangBuiltLinux/linux/issues/1865
Link: a178ba9fbd
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22ed903eee upstream.
syzbot detected a crash during log recovery:
XFS (loop0): Mounting V5 Filesystem bfdc47fc-10d8-4eed-a562-11a831b3f791
XFS (loop0): Torn write (CRC failure) detected at log block 0x180. Truncating head block from 0x200.
XFS (loop0): Starting recovery (logdev: internal)
==================================================================
BUG: KASAN: slab-out-of-bounds in xfs_btree_lookup_get_block+0x15c/0x6d0 fs/xfs/libxfs/xfs_btree.c:1813
Read of size 8 at addr ffff88807e89f258 by task syz-executor132/5074
CPU: 0 PID: 5074 Comm: syz-executor132 Not tainted 6.2.0-rc1-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/26/2022
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x1b1/0x290 lib/dump_stack.c:106
print_address_description+0x74/0x340 mm/kasan/report.c:306
print_report+0x107/0x1f0 mm/kasan/report.c:417
kasan_report+0xcd/0x100 mm/kasan/report.c:517
xfs_btree_lookup_get_block+0x15c/0x6d0 fs/xfs/libxfs/xfs_btree.c:1813
xfs_btree_lookup+0x346/0x12c0 fs/xfs/libxfs/xfs_btree.c:1913
xfs_btree_simple_query_range+0xde/0x6a0 fs/xfs/libxfs/xfs_btree.c:4713
xfs_btree_query_range+0x2db/0x380 fs/xfs/libxfs/xfs_btree.c:4953
xfs_refcount_recover_cow_leftovers+0x2d1/0xa60 fs/xfs/libxfs/xfs_refcount.c:1946
xfs_reflink_recover_cow+0xab/0x1b0 fs/xfs/xfs_reflink.c:930
xlog_recover_finish+0x824/0x920 fs/xfs/xfs_log_recover.c:3493
xfs_log_mount_finish+0x1ec/0x3d0 fs/xfs/xfs_log.c:829
xfs_mountfs+0x146a/0x1ef0 fs/xfs/xfs_mount.c:933
xfs_fs_fill_super+0xf95/0x11f0 fs/xfs/xfs_super.c:1666
get_tree_bdev+0x400/0x620 fs/super.c:1282
vfs_get_tree+0x88/0x270 fs/super.c:1489
do_new_mount+0x289/0xad0 fs/namespace.c:3145
do_mount fs/namespace.c:3488 [inline]
__do_sys_mount fs/namespace.c:3697 [inline]
__se_sys_mount+0x2d3/0x3c0 fs/namespace.c:3674
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
RIP: 0033:0x7f89fa3f4aca
Code: 83 c4 08 5b 5d c3 66 2e 0f 1f 84 00 00 00 00 00 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 49 89 ca b8 a5 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 c0 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007fffd5fb5ef8 EFLAGS: 00000206 ORIG_RAX: 00000000000000a5
RAX: ffffffffffffffda RBX: 00646975756f6e2c RCX: 00007f89fa3f4aca
RDX: 0000000020000100 RSI: 0000000020009640 RDI: 00007fffd5fb5f10
RBP: 00007fffd5fb5f10 R08: 00007fffd5fb5f50 R09: 000000000000970d
R10: 0000000000200800 R11: 0000000000000206 R12: 0000000000000004
R13: 0000555556c6b2c0 R14: 0000000000200800 R15: 00007fffd5fb5f50
</TASK>
The fuzzed image contains an AGF with an obviously garbage
agf_refcount_level value of 32, and a dirty log with a buffer log item
for that AGF. The ondisk AGF has a higher LSN than the recovered log
item. xlog_recover_buf_commit_pass2 reads the buffer, compares the
LSNs, and decides to skip replay because the ondisk buffer appears to be
newer.
Unfortunately, the ondisk buffer is corrupt, but recovery just read the
buffer with no buffer ops specified:
error = xfs_buf_read(mp->m_ddev_targp, buf_f->blf_blkno,
buf_f->blf_len, buf_flags, &bp, NULL);
Skipping the buffer leaves its contents in memory unverified. This sets
us up for a kernel crash because xfs_refcount_recover_cow_leftovers
reads the buffer (which is still around in XBF_DONE state, so no read
verification) and creates a refcountbt cursor of height 32. This is
impossible so we run off the end of the cursor object and crash.
Fix this by invoking the verifier on all skipped buffers and aborting
log recovery if the ondisk buffer is corrupt. It might be smarter to
force replay the log item atop the buffer and then see if it'll pass the
write verifier (like ext4 does) but for now let's go with the
conservative option where we stop immediately.
Link: https://syzkaller.appspot.com/bug?extid=7e9494b8b399902e994e
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 11c439a194 upstream.
IOMMU v2 page table supports 4 level (47 bit) or 5 level (56 bit) virtual
address space. Current code assumes it can support 64bit IOVA address
space. If IOVA allocator allocates virtual address > 47/56 bit (depending
on page table level) then it will do wrong mapping and cause invalid
translation.
Hence adjust aperture size to use max address supported by the page table.
Reported-by: Jerry Snitselaar <jsnitsel@redhat.com>
Fixes: aaac38f614 ("iommu/amd: Initial support for AMD IOMMU v2 page table")
Cc: <Stable@vger.kernel.org> # v6.0+
Cc: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Vasant Hegde <vasant.hegde@amd.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Link: https://lore.kernel.org/r/20230518054351.9626-1-vasant.hegde@amd.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
[ Modified to work with "V2 with 4 level page table" only - Vasant ]
Signed-off-by: Vasant Hegde <vasant.hegde@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c7e66e5fd upstream.
The TIS interrupt handler at least has to read and write the interrupt
status register. In case of SPI both operations result in a call to
tpm_tis_spi_transfer() which uses the bus_lock_mutex of the spi device
and thus must only be called from a sleepable context.
To ensure this request a threaded interrupt handler.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Tested-by: Michael Niewöhner <linux@mniewoehner.de>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3981514180 upstream.
Currently, when regmap_raw_write() splits the data, it uses the
max_raw_write value defined for the bus. For any bus that includes
the target register address in the max_raw_write value, the chunked
transmission will always exceed the maximum transmission length.
To avoid this problem, subtract the length of the register and the
padding from the maximum transmission.
Signed-off-by: Jim Wylder <jwylder@google.com
Link: https://lore.kernel.org/r/20230517152444.3690870-2-jwylder@google.com
Signed-off-by: Mark Brown <broonie@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c3d03e8e35 upstream.
Commit ac4e97abce ("scatterlist: sg_set_buf() argument must be in linear
mapping") checks that both the signature and the digest reside in the
linear mapping area.
However, more recently commit ba14a194a4 ("fork: Add generic vmalloced
stack support") made it possible to move the stack in the vmalloc area,
which is not contiguous, and thus not suitable for sg_set_buf() which needs
adjacent pages.
Always make a copy of the signature and digest in the same buffer used to
store the key and its parameters, and pass them to sg_init_one(). Prefer it
to conditionally doing the copy if necessary, to keep the code simple. The
buffer allocated with kmalloc() is in the linear mapping area.
Cc: stable@vger.kernel.org # 4.9.x
Fixes: ba14a194a4 ("fork: Add generic vmalloced stack support")
Link: https://lore.kernel.org/linux-integrity/Y4pIpxbjBdajymBJ@sol.localdomain/
Suggested-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Reviewed-by: Eric Biggers <ebiggers@google.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0512a5f89e upstream.
Check the remaining data length before accessing the context structure
to ensure that the entire structure is contained within the packet.
Additionally, since the context data length `ctxt_len` has already been
checked against the total packet length `len_of_ctxts`, update the
comparison to use `ctxt_len`.
Cc: stable@vger.kernel.org
Signed-off-by: Kuan-Ting Chen <h3xrabbit@gmail.com>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 36322523dd upstream.
If opinfo->conn is another connection and while ksmbd send oplock break
request to cient on current connection, The connection for opinfo->conn
can be disconnect and conn could be freed. When sending oplock break
request, this ksmbd_conn can be used and cause user-after-free issue.
When getting opinfo from the list, ksmbd check connection is being
released. If it is not released, Increase ->r_count to wait that connection
is freed.
Cc: stable@vger.kernel.org
Reported-by: Per Forlin <per.forlin@axis.com>
Tested-by: Per Forlin <per.forlin@axis.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84c5aa4792 upstream.
This patch fix the failure from smb2.credits.single_req_credits_granted
test. When client send 8192 credit request, ksmbd return 8191 credit
granted. ksmbd should give maximum possible credits that must be granted
within the range of not exceeding the max credit to client.
Cc: stable@vger.kernel.org
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4364b28798 upstream.
Bail from kvm_recalculate_phys_map() and disable the optimized map if the
target vCPU's x2APIC ID is out-of-bounds, i.e. if the vCPU was added
and/or enabled its local APIC after the map was allocated. This fixes an
out-of-bounds access bug in the !x2apic_format path where KVM would write
beyond the end of phys_map.
Check the x2APIC ID regardless of whether or not x2APIC is enabled,
as KVM's hardcodes x2APIC ID to be the vCPU ID, i.e. it can't change, and
the map allocation in kvm_recalculate_apic_map() doesn't check for x2APIC
being enabled, i.e. the check won't get false postivies.
Note, this also affects the x2apic_format path, which previously just
ignored the "x2apic_id > new->max_apic_id" case. That too is arguably a
bug fix, as ignoring the vCPU meant that KVM would not send interrupts to
the vCPU until the next map recalculation. In practice, that "bug" is
likely benign as a newly present vCPU/APIC would immediately trigger a
recalc. But, there's no functional downside to disabling the map, and
a future patch will gracefully handle the -E2BIG case by retrying instead
of simply disabling the optimized map.
Opportunistically add a sanity check on the xAPIC ID size, along with a
comment explaining why the xAPIC ID is guaranteed to be "good".
Reported-by: Michal Luczaj <mhal@rbox.co>
Fixes: 5b84b02917 ("KVM: x86: Honor architectural behavior for aliased 8-bit APIC IDs")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230602233250.1014316-2-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 817fa99836 upstream.
Factor in the address space (non-SMM vs. SMM) of the target shadow page
when recovering potential NX huge pages, otherwise KVM will retrieve the
wrong memslot when zapping shadow pages that were created for SMM. The
bug most visibly manifests as a WARN on the memslot being non-NULL, but
the worst case scenario is that KVM could unaccount the shadow page
without ensuring KVM won't install a huge page, i.e. if the non-SMM slot
is being dirty logged, but the SMM slot is not.
------------[ cut here ]------------
WARNING: CPU: 1 PID: 3911 at arch/x86/kvm/mmu/mmu.c:7015
kvm_nx_huge_page_recovery_worker+0x38c/0x3d0 [kvm]
CPU: 1 PID: 3911 Comm: kvm-nx-lpage-re
RIP: 0010:kvm_nx_huge_page_recovery_worker+0x38c/0x3d0 [kvm]
RSP: 0018:ffff99b284f0be68 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff99b284edd000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: ffff9271397024e0 R08: 0000000000000000 R09: ffff927139702450
R10: 0000000000000000 R11: 0000000000000001 R12: ffff99b284f0be98
R13: 0000000000000000 R14: ffff9270991fcd80 R15: 0000000000000003
FS: 0000000000000000(0000) GS:ffff927f9f640000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f0aacad3ae0 CR3: 000000088fc2c005 CR4: 00000000003726e0
Call Trace:
<TASK>
__pfx_kvm_nx_huge_page_recovery_worker+0x10/0x10 [kvm]
kvm_vm_worker_thread+0x106/0x1c0 [kvm]
kthread+0xd9/0x100
ret_from_fork+0x2c/0x50
</TASK>
---[ end trace 0000000000000000 ]---
This bug was exposed by commit edbdb43fc9 ("KVM: x86: Preserve TDP MMU
roots until they are explicitly invalidated"), which allowed KVM to retain
SMM TDP MMU roots effectively indefinitely. Before commit edbdb43fc9,
KVM would zap all SMM TDP MMU roots and thus all SMM TDP MMU shadow pages
once all vCPUs exited SMM, which made the window where this bug (recovering
an SMM NX huge page) could be encountered quite tiny. To hit the bug, the
NX recovery thread would have to run while at least one vCPU was in SMM.
Most VMs typically only use SMM during boot, and so the problematic shadow
pages were gone by the time the NX recovery thread ran.
Now that KVM preserves TDP MMU roots until they are explicitly invalidated
(e.g. by a memslot deletion), the window to trigger the bug is effectively
never closed because most VMMs don't delete memslots after boot (except
for a handful of special scenarios).
Fixes: eb29860570 ("KVM: x86/mmu: Do not recover dirty-tracked NX Huge Pages")
Reported-by: Fabio Coatti <fabio.coatti@gmail.com>
Closes: https://lore.kernel.org/all/CADpTngX9LESCdHVu_2mQkNGena_Ng2CphWNwsRGSMxzDsTjU2A@mail.gmail.com
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230602010137.784664-1-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f6a27d6dc5 upstream.
The reference count on page table allocations is increased for every
'counted' PTE (valid or donated) in the table in addition to the initial
reference from ->zalloc_page(). kvm_pgtable_stage2_free_removed() fails
to drop the last reference on the root of the table walk, meaning we
leak memory.
Fix it by dropping the last reference after the free walker returns,
at which point all references for 'counted' PTEs have been released.
Cc: stable@vger.kernel.org
Fixes: 5c359cca1f ("KVM: arm64: Tear down unlinked stage-2 subtree after break-before-make")
Reported-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Tested-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230530193213.1663411-1-oliver.upton@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4acfe3dfde upstream.
Dan Carpenter spotted a race condition in a couple of situations like
these in the test_firmware driver:
static int test_dev_config_update_u8(const char *buf, size_t size, u8 *cfg)
{
u8 val;
int ret;
ret = kstrtou8(buf, 10, &val);
if (ret)
return ret;
mutex_lock(&test_fw_mutex);
*(u8 *)cfg = val;
mutex_unlock(&test_fw_mutex);
/* Always return full write size even if we didn't consume all */
return size;
}
static ssize_t config_num_requests_store(struct device *dev,
struct device_attribute *attr,
const char *buf, size_t count)
{
int rc;
mutex_lock(&test_fw_mutex);
if (test_fw_config->reqs) {
pr_err("Must call release_all_firmware prior to changing config\n");
rc = -EINVAL;
mutex_unlock(&test_fw_mutex);
goto out;
}
mutex_unlock(&test_fw_mutex);
rc = test_dev_config_update_u8(buf, count,
&test_fw_config->num_requests);
out:
return rc;
}
static ssize_t config_read_fw_idx_store(struct device *dev,
struct device_attribute *attr,
const char *buf, size_t count)
{
return test_dev_config_update_u8(buf, count,
&test_fw_config->read_fw_idx);
}
The function test_dev_config_update_u8() is called from both the locked
and the unlocked context, function config_num_requests_store() and
config_read_fw_idx_store() which can both be called asynchronously as
they are driver's methods, while test_dev_config_update_u8() and siblings
change their argument pointed to by u8 *cfg or similar pointer.
To avoid deadlock on test_fw_mutex, the lock is dropped before calling
test_dev_config_update_u8() and re-acquired within test_dev_config_update_u8()
itself, but alas this creates a race condition.
Having two locks wouldn't assure a race-proof mutual exclusion.
This situation is best avoided by the introduction of a new, unlocked
function __test_dev_config_update_u8() which can be called from the locked
context and reducing test_dev_config_update_u8() to:
static int test_dev_config_update_u8(const char *buf, size_t size, u8 *cfg)
{
int ret;
mutex_lock(&test_fw_mutex);
ret = __test_dev_config_update_u8(buf, size, cfg);
mutex_unlock(&test_fw_mutex);
return ret;
}
doing the locking and calling the unlocked primitive, which enables both
locked and unlocked versions without duplication of code.
The similar approach was applied to all functions called from the locked
and the unlocked context, which safely mitigates both deadlocks and race
conditions in the driver.
__test_dev_config_update_bool(), __test_dev_config_update_u8() and
__test_dev_config_update_size_t() unlocked versions of the functions
were introduced to be called from the locked contexts as a workaround
without releasing the main driver's lock and thereof causing a race
condition.
The test_dev_config_update_bool(), test_dev_config_update_u8() and
test_dev_config_update_size_t() locked versions of the functions
are being called from driver methods without the unnecessary multiplying
of the locking and unlocking code for each method, and complicating
the code with saving of the return value across lock.
Fixes: 7feebfa487 ("test_firmware: add support for request_firmware_into_buf")
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Russ Weight <russell.h.weight@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Tianfei Zhang <tianfei.zhang@intel.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Colin Ian King <colin.i.king@gmail.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: linux-kselftest@vger.kernel.org
Cc: stable@vger.kernel.org # v5.4
Suggested-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr>
Link: https://lore.kernel.org/r/20230509084746.48259-1-mirsad.todorovac@alu.unizg.hr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 719dfd5925 upstream.
kallsyms_lookup() which in turn calls kallsyms_lookup_buildid() writes
to index "KSYM_NAME_LEN - 1".
Thus the array passed as namebuf to kallsyms_lookup() should be
KSYM_NAME_LEN in size.
In xmon.c the array was defined to be "128" bytes directly, without
using KSYM_NAME_LEN. Commit b8a94bfb33 ("kallsyms: increase maximum
kernel symbol length to 512") changed the value to 512, but missed
updating the xmon code.
Fixes: b8a94bfb33 ("kallsyms: increase maximum kernel symbol length to 512")
Cc: stable@vger.kernel.org # v6.1+
Co-developed-by: Onkarnath <onkarnath.1@samsung.com>
Signed-off-by: Onkarnath <onkarnath.1@samsung.com>
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
[mpe: Tweak change log wording and fix commit reference]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230529111337.352990-2-maninder1.s@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 55b47ca7d8 upstream.
Active subflow are inserted into the connection list at creation time.
When the MPJ handshake completes successfully, a new subflow creation
netlink event is generated correctly, but the current code wrongly
avoid initializing a couple of subflow data.
The above will cause misbehavior on a few exceptional events: unneeded
mptcp-level retransmission on msk-level sequence wrap-around and infinite
mapping fallback even when a MPJ socket is present.
Address the issue factoring out the needed initialization in a new helper
and invoking the latter from __mptcp_finish_join() time for passive
subflow and from mptcp_finish_join() for active ones.
Fixes: 0530020a7c ("mptcp: track and update contiguous data status")
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 786fc12457 upstream.
Ondrej reported a functional issue WRT timeout handling on connect
with a nice reproducer.
The problem is that the current mptcp connect waits for both the
MPTCP socket level timeout, and the first subflow socket timeout.
The latter is not influenced/touched by the exposed setsockopt().
Overall the above makes the SO_SNDTIMEO a no-op on connect.
Since mptcp_connect is invoked via inet_stream_connect and the
latter properly handle the MPTCP level timeout, we can address the
issue making the nested subflow level connect always unblocking.
This also allow simplifying a bit the code, dropping an ugly hack
to handle the fastopen and custom proto_ops connect.
The issues predates the blamed commit below, but the current resolution
requires the infrastructure introduced there.
Fixes: 54f1944ed6 ("mptcp: factor out mptcp_connect()")
Reported-by: Ondrej Mosnacek <omosnace@redhat.com>
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/399
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d83013bdf9 upstream.
Selftests are supposed to run on any kernels, including the old ones not
supporting MPTCP.
A new check is then added to make sure MPTCP is supported. If not, the
test stops and is marked as "skipped". Note that this check can also
mark the test as failed if 'SELFTESTS_MPTCP_LIB_EXPECT_ALL_FEATURES' env
var is set to 1: by doing that, we can make sure a test is not being
skipped by mistake.
A new shared file is added here to be able to re-used the same check in
the different selftests we have.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: 048d19d444 ("mptcp: add basic kselftest for mptcp")
Cc: stable@vger.kernel.org
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e30fbc618e upstream.
Modifiers are used to change the behavior of keys. For instance, they
can grouped into buckets, converted to syscall names (from the syscall
identifier), show task->comm of the current pid, be an array of longs
that represent a stacktrace, and more.
It was found that nothing stopped a value from taking a modifier. As
values are simple counters. If this happened, it would call code that
was not expecting a modifier and crash the kernel. This was fixed by
having the ___create_val_field() function test if a modifier was present
and fail if one was. This fixed the crash.
Now there's a problem with variables. Variables are used to pass fields
from one event to another. Variables are allowed to have some modifiers,
as the processing may need to happen at the time of the event (like
stacktraces and comm names of the current pid). The issue is that it too
uses __create_val_field(). Now that fails on modifiers, variables can no
longer use them (this is a regression).
As not all modifiers are for variables, have them use a separate check.
Link: https://lore.kernel.org/linux-trace-kernel/20230523221108.064a5d82@rorschach.local.home
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Tom Zanussi <zanussi@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Fixes: e0213434fe ("tracing: Do not let histogram values have some modifiers")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 632478a058 upstream.
While testing rtla timerlat auto analysis, I reach a condition where
the interface was not receiving tracing data. I was able to manually
reproduce the problem with these steps:
# echo 0 > tracing_on # disable trace
# echo 1 > osnoise/stop_tracing_us # stop trace if timerlat irq > 1 us
# echo timerlat > current_tracer # enable timerlat tracer
# sleep 1 # wait... that is the time when rtla
# apply configs like prio or cgroup
# echo 1 > tracing_on # start tracing
# cat trace
# tracer: timerlat
#
# _-----=> irqs-off
# / _----=> need-resched
# | / _---=> hardirq/softirq
# || / _--=> preempt-depth
# ||| / _-=> migrate-disable
# |||| / delay
# ||||| ACTIVATION
# TASK-PID CPU# ||||| TIMESTAMP ID CONTEXT LATENCY
# | | | ||||| | | | |
NOTHING!
Then, trying to enable tracing again with echo 1 > tracing_on resulted
in no change: the trace was still not tracing.
This problem happens because the timerlat IRQ hits the stop tracing
condition while tracing is off, and do not wake up the timerlat thread,
so the timerlat threads are kept sleeping forever, resulting in no
trace, even after re-enabling the tracer.
Avoid this condition by always waking up the threads, even after stopping
tracing, allowing the tracer to return to its normal operating after
a new tracing on.
Link: https://lore.kernel.org/linux-trace-kernel/1ed8f830638b20a39d535d27d908e319a9a3c4e2.1683822622.git.bristot@kernel.org
Cc: Juri Lelli <juri.lelli@redhat.com>
Cc: stable@vger.kernel.org
Fixes: a955d7eac1 ("trace: Add timerlat tracer")
Signed-off-by: Daniel Bristot de Oliveira <bristot@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ea923f443 upstream.
The addition of the mtdchar_read_ioctl() function caused the stack usage
of mtdchar_ioctl() to grow beyond the warning limit on 32-bit architectures
with gcc-13:
drivers/mtd/mtdchar.c: In function 'mtdchar_ioctl':
drivers/mtd/mtdchar.c:1229:1: error: the frame size of 1488 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
Mark both the read and write portions as noinline_for_stack to ensure
they don't get inlined and use separate stack slots to reduce the
maximum usage, both in the mtdchar_ioctl() and combined with any
of its callees.
Fixes: 095bb6e44e ("mtdchar: add MEMREAD ioctl")
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230417205654.1982368-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42c4e97e06 upstream.
The Linux Kernel currently only requires make v3.82 while the grouped
target functionality requires make v4.3. Removed the grouped target
introduced in 4ce1f694eb ("selinux: ensure av_permissions.h is
built when needed") as well as the multiple header file targets in
the make rule. This effectively reverts the problem commit.
We will revisit this change when make >= 4.3 is required by the rest
of the kernel.
Cc: stable@vger.kernel.org
Fixes: 4ce1f694eb ("selinux: ensure av_permissions.h is built when needed")
Reported-by: Erwan Velu <e.velu@criteo.com>
Reported-by: Luiz Capitulino <luizcap@amazon.com>
Tested-by: Luiz Capitulino <luizcap@amazon.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a7e8ec0d4 upstream.
For RISC-V, when tracing with tracepoint events, the IP and status are
set to 0, preventing the perf code parsing the callchain and resolving
the symbols correctly.
./ply 'tracepoint:kmem/kmem_cache_alloc { @[stack]=count(); }'
@:
{ <STACKID4294967282> }: 1
The fix is to implement perf_arch_fetch_caller_regs for riscv, which
fills several necessary registers used for callchain unwinding,
including epc, sp, s0 and status. It's similar to commit b3eac0265b
("arm: perf: Fix callchain parse error with kernel tracepoint events")
and commit 5b09a094f2 ("arm64: perf: Fix callchain parse error with
kernel tracepoint events").
With this patch, callchain can be parsed correctly as:
./ply 'tracepoint:kmem/kmem_cache_alloc { @[stack]=count(); }'
@:
{
__traceiter_kmem_cache_alloc+68
__traceiter_kmem_cache_alloc+68
kmem_cache_alloc+354
__sigqueue_alloc+94
__send_signal_locked+646
send_signal_locked+154
do_send_sig_info+84
__kill_pgrp_info+130
kill_pgrp+60
isig+150
n_tty_receive_signal_char+36
n_tty_receive_buf_standard+2214
n_tty_receive_buf_common+280
n_tty_receive_buf2+26
tty_ldisc_receive_buf+34
tty_port_default_receive_buf+62
flush_to_ldisc+158
process_one_work+458
worker_thread+138
kthread+178
riscv_cpufeature_patch_func+832
}: 1
Signed-off-by: Ism Hong <ism.hong@gmail.com>
Link: https://lore.kernel.org/r/20230601095355.1168910-1-ism.hong@gmail.com
Fixes: 178e9fc47a ("perf: riscv: preliminary RISC-V support")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c28afd551 upstream.
It seems we forgot the normal case to terminate the retry loop,
making us asking 3 times each command, which is probably a little bit
too much.
And remove the ugly "goto exit" that can be replaced by a simpler "break"
Fixes: 586e8fede7 ("HID: logitech-hidpp: Retry commands when device is busy")
Suggested-by: Mark Lord <mlord@pobox.com>
Tested-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 45c2f36871 ]
When I implemented the storage layer bio splitting, I was under the
assumption that we'll never split metadata bios. But Qu reminded me that
this can actually happen with very old file systems with unaligned
metadata chunks and RAID0.
I still haven't seen such a case in practice, but we better handled this
case, especially as it is fairly easily to do not calling the ->end_іo
method directly in btrfs_end_io_work, and using the proper
btrfs_orig_bbio_end_io helper instead.
In addition to the old file system with unaligned metadata chunks case
documented in the commit log, the combination of the new scrub code
with Johannes pending raid-stripe-tree also triggers this case. We
spent some time debugging it and found that this patch solves
the problem.
Fixes: 103c19723c ("btrfs: split the bio submission path into a separate file")
CC: stable@vger.kernel.org # 6.3+
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Tested-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6e766dea0 ]
If a map request is made with securemap attribute, the memory
ownership needs to be reassigned to new VMID to allow access
from protection domain. Currently only DSP VMID is passed to
the reassign call which is incorrect as only a combination of
HLOS and DSP VMID is allowed for memory ownership reassignment
and passing only DSP VMID will cause assign call failure.
Also pass proper restoring permissions to HLOS as the source
permission will now carry both HLOS and DSP VMID permission.
Change is also made to get valid physical address from
scatter/gather for this allocation request.
Fixes: e90d911906 ("misc: fastrpc: Add support to secure memory map")
Cc: stable <stable@kernel.org>
Tested-by: Ekansh Gupta <quic_ekangupt@quicinc.com>
Signed-off-by: Ekansh Gupta <quic_ekangupt@quicinc.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230523152550.438363-2-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fadb74f9f2 upstream.
While implementing support for in-kernel decompression in kmod,
finit_module() was returning a very suspicious value:
finit_module(3, "", MODULE_INIT_COMPRESSED_FILE) = 18446744072717407296
It turns out the check for module_get_next_page() failing is wrong,
and hence the decompression was not really taking place. Invert
the condition to fix it.
Fixes: 169a58ad82 ("module/decompress: Support zstd in-kernel decompression")
Cc: stable@kernel.org
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ecd704a4c upstream.
With commit 858e8b792d ("tpm, tpm_tis: Avoid cache incoherency in test
for interrupts") bit accessor functions are used to access flags in
tpm_tis_data->flags.
However these functions expect bit numbers, while the flags are defined
as bit masks in enum tpm_tis_flag.
Fix this inconsistency by using numbers instead of masks also for the
flags in the enum.
Reported-by: Pavel Machek <pavel@denx.de>
Fixes: 858e8b792d ("tpm, tpm_tis: Avoid cache incoherency in test for interrupts")
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Cc: stable@vger.kernel.org
Reviewed-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d2ccf00bd upstream.
Currently in tce_freemulti_pSeriesLP() there is no limit on how many
TCEs are passed to the H_STUFF_TCE hcall. This has not caused an issue
until now, but newer firmware releases have started enforcing a limit of
512 TCEs per call.
The limit is correct per the specification (PAPR v2.12 § 14.5.4.2.3).
The code has been in it's current form since it was initially merged.
Cc: stable@vger.kernel.org
Signed-off-by: Gaurav Batra <gbatra@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
[mpe: Tweak change log wording & add PAPR reference]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230525143454.56878-1-gbatra@linux.vnet.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47fe1c3064 upstream.
The scsi driver function sd_read_block_characteristics() always calls
disk_set_zoned() to a disk zoned model correctly, in case the device
model changed. This is done even for regular disks to set the zoned
model to BLK_ZONED_NONE and free any zone related resources if the drive
previously was zoned.
This behavior significantly impact the time it takes to revalidate disks
on a large system as the call to disk_clear_zone_settings() done from
disk_set_zoned() for the BLK_ZONED_NONE case results in the device
request queued to be frozen, even if there are no zone resources to
free.
Avoid this overhead for non-zoned devices by not calling
disk_clear_zone_settings() in disk_set_zoned() if the device model
was already set to BLK_ZONED_NONE, which is always the case for regular
devices.
Reported by: Brian Bunker <brian@purestorage.com>
Fixes: 508aebb805 ("block: introduce blk_queue_clear_zone_settings()")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230529073237.1339862-1-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ad9b4719f upstream.
When compiling on a MIPS 64-bit machine we get these warnings:
In file included from ./arch/mips/include/asm/cacheflush.h:13,
from ./include/linux/cacheflush.h:5,
from ./include/linux/highmem.h:8,
from ./include/linux/bvec.h:10,
from ./include/linux/blk_types.h:10,
from ./include/linux/blkdev.h:9,
from fs/btrfs/disk-io.c:7:
fs/btrfs/disk-io.c: In function ‘csum_tree_block’:
fs/btrfs/disk-io.c:100:34: error: array subscript 1 is above array bounds of ‘struct page *[1]’ [-Werror=array-bounds]
100 | kaddr = page_address(buf->pages[i]);
| ~~~~~~~~~~^~~
./include/linux/mm.h:2135:48: note: in definition of macro ‘page_address’
2135 | #define page_address(page) lowmem_page_address(page)
| ^~~~
cc1: all warnings being treated as errors
We can check if i overflows to solve the problem. However, this doesn't make
much sense, since i == 1 and num_pages == 1 doesn't execute the body of the loop.
In addition, i < num_pages can also ensure that buf->pages[i] will not cross
the boundary. Unfortunately, this doesn't help with the problem observed here:
gcc still complains.
To fix this add a compile-time condition for the extent buffer page
array size limit, which would eventually lead to eliminating the whole
for loop.
CC: stable@vger.kernel.org # 5.10+
Signed-off-by: pengfuyuan <pengfuyuan@kylinos.cn>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2474e05467 upstream.
LPUART IP now has two known bugs, one is that CTS has higher priority
than the break signal, which causes the break signal sending through
UARTCTRL_SBK may impacted by the CTS input if the HW flow control is
enabled. It exists on all platforms we support in this driver.
So we add a workaround patch for this issue: commit c4c81db5cf
("tty: serial: fsl_lpuart: disable the CTS when send break signal").
Another IP bug is i.MX8QM LPUART may have an additional break character
being sent after SBK was cleared. It may need to add some delay between
clearing SBK and re-enabling CTS to ensure that the SBK latch are
completely cleared.
But we found that during the delay period before CTS is enabled, there
is still a risk that Bluetooth data in TX FIFO may be sent out during
this period because of break off and CTS disabled(even if BT sets CTS
line deasserted, data is still sent to BT).
Due to this risk, we have to drop the CTS-disabling workaround for SBK
bugs, use TXINV seems to be a better way to replace SBK feature and
avoid above risk. Also need to disable the transmitter to prevent any
data from being sent out during break, then invert the TX line to send
break. Then disable the TXINV when turn off break and re-enable
transmitter.
Fixes: c4c81db5cf ("tty: serial: fsl_lpuart: disable the CTS when send break signal")
Cc: stable <stable@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230519094751.28948-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a99d21cefd upstream.
We may get an empty response with zero length at the beginning of
the driver start and get following UBSAN error. Since there is no
content(SDRT_NONE) for the response, just return and skip the response
handling to avoid this problem.
Test pass : SDIO wifi throughput test with this patch
[ 126.980684] UBSAN: array-index-out-of-bounds in drivers/mmc/host/vub300.c:1719:12
[ 126.980709] index -1 is out of range for type 'u32 [4]'
[ 126.980729] CPU: 4 PID: 9 Comm: kworker/u16:0 Tainted: G E 6.3.0-rc4-mtk-local-202304272142 #1
[ 126.980754] Hardware name: Intel(R) Client Systems NUC8i7BEH/NUC8BEB, BIOS BECFL357.86A.0081.2020.0504.1834 05/04/2020
[ 126.980770] Workqueue: kvub300c vub300_cmndwork_thread [vub300]
[ 126.980833] Call Trace:
[ 126.980845] <TASK>
[ 126.980860] dump_stack_lvl+0x48/0x70
[ 126.980895] dump_stack+0x10/0x20
[ 126.980916] ubsan_epilogue+0x9/0x40
[ 126.980944] __ubsan_handle_out_of_bounds+0x70/0x90
[ 126.980979] vub300_cmndwork_thread+0x58e7/0x5e10 [vub300]
[ 126.981018] ? _raw_spin_unlock+0x18/0x40
[ 126.981042] ? finish_task_switch+0x175/0x6f0
[ 126.981070] ? __switch_to+0x42e/0xda0
[ 126.981089] ? __switch_to_asm+0x3a/0x80
[ 126.981129] ? __pfx_vub300_cmndwork_thread+0x10/0x10 [vub300]
[ 126.981174] ? __kasan_check_read+0x11/0x20
[ 126.981204] process_one_work+0x7ee/0x13d0
[ 126.981246] worker_thread+0x53c/0x1240
[ 126.981291] kthread+0x2b8/0x370
[ 126.981312] ? __pfx_worker_thread+0x10/0x10
[ 126.981336] ? __pfx_kthread+0x10/0x10
[ 126.981359] ret_from_fork+0x29/0x50
[ 126.981400] </TASK>
Fixes: 88095e7b47 ("mmc: Add new VUB300 USB-to-SD/SDIO/MMC driver")
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/048cd6972c50c33c2e8f81d5228fed928519918b.1683987673.git.deren.wu@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 55e02c14f9 upstream.
This patch reverses the DPM clocks levels output of pp_dpm_mclk
and pp_dpm_fclk for renoir.
On dGPUs and older APUs we expose the levels from lowest clocks
to highest clocks. But for some APUs, the clocks levels are
given the reversed orders by PMFW. Like the memory DPM clocks
that are exposed by pp_dpm_mclk.
It's not intuitive that they are reversed on these APUs. All tools
and software that talks to the driver then has to know different ways
to interpret the data depending on the asic.
So we need to reverse them to expose the clocks levels from the
driver consistently.
Signed-off-by: Tim Huang <Tim.Huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f1373a97a4 upstream.
This patch reverses the DPM clocks levels output of pp_dpm_mclk
and pp_dpm_fclk.
On dGPUs and older APUs we expose the levels from lowest clocks
to highest clocks. But for some APUs, the clocks levels that from
the DFPstateTable are given the reversed orders by PMFW. Like the
memory DPM clocks that are exposed by pp_dpm_mclk.
It's not intuitive that they are reversed on these APUs. All tools
and software that talks to the driver then has to know different ways
to interpret the data depending on the asic.
So we need to reverse them to expose the clocks levels from the
driver consistently.
Signed-off-by: Tim Huang <Tim.Huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1d35412b3 upstream.
This patch reverses the DPM clocks levels output of pp_dpm_mclk.
On dGPUs and older APUs we expose the levels from lowest clocks
to highest clocks. But for some APUs, the clocks levels that from
the DFPstateTable are given the reversed orders by PMFW. Like the
memory DPM clocks that are exposed by pp_dpm_mclk.
It's not intuitive that they are reversed on these APUs. All tools
and software that talks to the driver then has to know different ways
to interpret the data depending on the asic.
So we need to reverse them to expose the clocks levels from the
driver consistently.
Signed-off-by: Tim Huang <Tim.Huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bfc03568d9 upstream.
This patch reverses the DPM clocks levels output of pp_dpm_mclk
and pp_dpm_fclk.
On dGPUs and older APUs we expose the levels from lowest clocks
to highest clocks. But for some APUs, the clocks levels that from
the DFPstateTable are given the reversed orders by PMFW. Like the
memory DPM clocks that are exposed by pp_dpm_mclk.
It's not intuitive that they are reversed on these APUs. All tools
and software that talks to the driver then has to know different ways
to interpret the data depending on the asic.
So we need to reverse them to expose the clocks levels from the
driver consistently.
Signed-off-by: Tim Huang <Tim.Huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6a07826f20 upstream.
This patch reverses the DPM clocks levels output of pp_dpm_mclk
and pp_dpm_fclk.
On dGPUs and older APUs we expose the levels from lowest clocks
to highest clocks. But for some APUs, the clocks levels that from
the DFPstateTable are given the reversed orders by PMFW. Like the
memory DPM clocks that are exposed by pp_dpm_mclk.
It's not intuitive that they are reversed on these APUs. All tools
and software that talks to the driver then has to know different ways
to interpret the data depending on the asic.
So we need to reverse them to expose the clocks levels from the
driver consistently.
Signed-off-by: Tim Huang <Tim.Huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f875850f2 upstream.
For devices not attached to a port multiplier and managed directly by
libata, the device number passed to ata_find_dev() must always be lower
than the maximum number of devices returned by ata_link_max_devices().
That is 1 for SATA devices or 2 for an IDE link with master+slave
devices. This device number is the SCSI device ID which matches these
constraints as the IDs are generated per port and so never exceed the
maximum number of devices for the link being used.
However, for libsas managed devices, SCSI device IDs are assigned per
struct scsi_host, leading to device IDs for SATA devices that can be
well in excess of libata per-link maximum number of devices. This
results in ata_find_dev() to always return NULL for libsas managed
devices except for the first device of the target scsi_host with ID
(device number) equal to 0. This issue is visible by executing the
hdparm utility, which fails. E.g.:
hdparm -i /dev/sdX
/dev/sdX:
HDIO_GET_IDENTITY failed: No message of desired type
Fix this by rewriting ata_find_dev() to ignore the device number for
non-PMP attached devices with a link with at most 1 device, that is SATA
devices. For these, the device number 0 is always used to
return the correct pointer to the struct ata_device of the port link.
This change excludes IDE master/slave setups (maximum number of devices
per link is 2) and port-multiplier attached devices. Also, to be
consistant with the fact that SCSI device IDs and channel numbers used
as device numbers are both unsigned int, change the devno argument of
ata_find_dev() to unsigned int.
Reported-by: Xingui Yang <yangxingui@huawei.com>
Fixes: 41bda9c980 ("libata-link: update hotplug to handle PMP links")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d074ce231 upstream.
gcc 13 may assign another type to enumeration constants than gcc 12. Split
the large enum at the top of source file stex.c such that the type of the
constants used in time expressions is changed back to the same type chosen
by gcc 12. This patch suppresses compiler warnings like this one:
In file included from ./include/linux/bitops.h:7,
from ./include/linux/kernel.h:22,
from drivers/scsi/stex.c:13:
drivers/scsi/stex.c: In function ‘stex_common_handshake’:
./include/linux/typecheck.h:12:25: error: comparison of distinct pointer types lacks a cast [-Werror]
12 | (void)(&__dummy == &__dummy2); \
| ^~
./include/linux/jiffies.h:106:10: note: in expansion of macro ‘typecheck’
106 | typecheck(unsigned long, b) && \
| ^~~~~~~~~
drivers/scsi/stex.c:1035:29: note: in expansion of macro ‘time_after’
1035 | if (time_after(jiffies, before + MU_MAX_DELAY * HZ)) {
| ^~~~~~~~~~
See also https://gcc.gnu.org/bugzilla/show_bug.cgi?id=107405.
Cc: stable@vger.kernel.org
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20230529195034.3077-1-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46248400d8 upstream.
The channel's rpmsg object allows new invocations to be made. After old
invocations are already interrupted, the driver shouldn't try to invoke
anymore. Invalidating the rpmsg at the end of the driver removal
function makes it easy to cause a race condition in userspace. Even
closing a file descriptor before the driver finishes its cleanup can
cause an invocation via fastrpc_release_current_dsp_process() and
subsequent timeout.
Invalidate the channel before the invocations are interrupted to make
sure that no invocations can be created to hang after the device closes.
Fixes: c68cfb718c ("misc: fastrpc: Add support for context Invoke method")
Cc: stable <stable@kernel.org>
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230523152550.438363-5-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c7d0079a1 upstream.
The userspace map request for remote heap allocates CMA memory.
The ownership of this memory needs to be reassigned to proper
owners to allow access from the protection domain running on
DSP. This reassigning of ownership is not correct if done for
any other supported flags.
When any other flag is requested from userspace, fastrpc is
trying to reassign the ownership of memory and this reassignment
is getting skipped for remote heap request which is incorrect.
Add proper flag check to reassign the memory only if remote heap
is requested.
Fixes: 532ad70c6d ("misc: fastrpc: Add mmap request assigning for static PD pool")
Cc: stable <stable@kernel.org>
Tested-by: Ekansh Gupta <quic_ekangupt@quicinc.com>
Signed-off-by: Ekansh Gupta <quic_ekangupt@quicinc.com>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230523152550.438363-3-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit efb6b53520 upstream.
While exercising the unbind path, with the current implementation
the functionfs_unbind would be calling which waits for the ffs->mutex
to be available, however within the same time ffs_ep0_read is invoked
& if no setup packets are pending, it will invoke function
wait_event_interruptible_exclusive_locked_irq which by definition waits
for the ev.count to be increased inside the same mutex for which
functionfs_unbind is waiting.
This creates deadlock situation because the functionfs_unbind won't
get the lock until ev.count is increased which can only happen if
the caller ffs_func_unbind can proceed further.
Following is the illustration:
CPU1 CPU2
ffs_func_unbind() ffs_ep0_read()
mutex_lock(ffs->mutex)
wait_event(ffs->ev.count)
functionfs_unbind()
mutex_lock(ffs->mutex)
mutex_unlock(ffs->mutex)
ffs_event_add()
<deadlock>
Fix this by moving the event unbind before functionfs_unbind
to ensure the ev.count is incrased properly.
Fixes: 6a19da1110 ("usb: gadget: f_fs: Prevent race during ffs_ep0_queue_wait")
Cc: stable <stable@kernel.org>
Signed-off-by: Uttkarsh Aggarwal <quic_uaggarwa@quicinc.com>
Link: https://lore.kernel.org/r/20230525092854.7992-1-quic_uaggarwa@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dbe678f619 upstream.
At iMX8QM platform, enable NCM gadget and run 'iperf3 -s'.
At host, run 'iperf3 -V -c fe80::6863:98ff:feef:3e0%enxc6e147509498'
[ 5] 0.00-1.00 sec 1.55 MBytes 13.0 Mbits/sec 90 4.18 KBytes
[ 5] 1.00-2.00 sec 1.44 MBytes 12.0 Mbits/sec 75 4.18 KBytes
[ 5] 2.00-3.00 sec 1.48 MBytes 12.4 Mbits/sec 75 4.18 KBytes
Expected speed should be bigger than 300Mbits/sec.
The root cause of this performance drop was found to be data corruption
happening at 4K borders in some Ethernet packets, leading to TCP
checksum errors. This corruption occurs from the position
(4K - (address & 0x7F)) to 4K. The u_ether function's allocation of
skb_buff reserves 64B, meaning all RX addresses resemble 0xXXXX0040.
Force trb_burst_size to 16 can fix this problem.
Cc: stable@vger.kernel.org
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20230518154946.3666662-1-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a146eccb68 upstream.
Commit 28d1a7ac2a ("iio: dac: Add AD5758 support") adds the config AD5758
and the corresponding driver ad5758.c. In the Makefile, the ad5758 driver
is however included when AD5755 is selected, not when AD5758 is selected.
Probably, this was simply a mistake that happened by copy-and-paste and
forgetting to adjust the actual line. Surprisingly, no one has ever noticed
that this driver is actually only included when AD5755 is selected and that
the config AD5758 has actually no effect on the build.
Fixes: 28d1a7ac2a ("iio: dac: Add AD5758 support")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20230508040208.12033-1-lukas.bulwahn@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e55245d115 upstream.
The AD7192 provides a specific channel configuration where both negative
and positive inputs are connected to AIN2. This was represented in the
ad7192 driver as a IIO channel with .channel = 2 and .extended_name set
to "shorted".
The problem with this approach, is that the driver provided two IIO
channels with the identifier .channel = 2; one "shorted" and the other
not. This goes against the IIO ABI, as a channel identifier should be
unique.
Address this issue by changing "shorted" channels to being differential
instead, with channel 2 vs. itself, as we're actually measuring AIN2 vs.
itself.
Note that the fix tag is for the commit that moved the driver out of
staging. The bug existed before that, but backporting would become very
complex further down and unlikely to happen.
Fixes: b581f748cc ("staging: iio: adc: ad7192: move out of staging")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Co-developed-by: Alisa Roman <alisa.roman@analog.com>
Signed-off-by: Alisa Roman <alisa.roman@analog.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230330102100.17590-1-paul@crapouillou.net
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 626d312028 upstream.
The Sigma-Delta ADCs supported by this driver can use SDO as an interrupt
line to indicate the completion of a conversion. However, some devices
cannot properly detect the completion of a conversion by an interrupt.
This is for the reason mentioned in the following commit.
commit e9849777d0 ("genirq: Add flag to force mask in
disable_irq[_nosync]()")
A read operation is performed by an extra interrupt before the completion
of a conversion. At this time, the value read from the ADC data register
is the same as the previous conversion result. This patch fixes the issue
by setting IRQ_DISABLE_UNLAZY flag.
Fixes: 0c6ef985a1 ("iio: adc: ad7791: fix IRQ flags")
Fixes: 1a913270e5 ("iio: adc: ad7793: Fix IRQ flag")
Fixes: e081102f30 ("iio: adc: ad7780: Fix IRQ flag")
Fixes: 89a86da5cb ("iio: adc: ad7192: Add IRQ flag")
Fixes: 79ef91493f ("iio: adc: ad7124: Set IRQ type to falling")
Signed-off-by: Masahiro Honda <honda@mechatrax.com>
Link: https://lore.kernel.org/r/20230518110816.248-1-honda@mechatrax.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd249b9197 upstream.
If high bit is set to 1 in ((data[3] & 0x0f << 28), after all arithmetic
operations and integer promotions are done, high bits in
wacom->serial[idx] will be filled with 1s as well.
Avoid this, albeit unlikely, issue by specifying left operand's __u64
type for the right operand.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: 3bea733ab2 ("USB: wacom tablet driver reorganization")
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 27b2ed5b6d upstream.
Smatch reports:
drivers/iio/adc/mxs-lradc-adc.c:766 mxs_lradc_adc_probe() warn:
missing unwind goto?
the order of three init operation:
1.mxs_lradc_adc_trigger_init
2.iio_triggered_buffer_setup
3.mxs_lradc_adc_hw_init
thus, the order of three cleanup operation should be:
1.mxs_lradc_adc_hw_stop
2.iio_triggered_buffer_cleanup
3.mxs_lradc_adc_trigger_remove
we exchange the order of two cleanup operations,
introducing the following differences:
1.if mxs_lradc_adc_trigger_init fails, returns directly;
2.if trigger_init succeeds but iio_triggered_buffer_setup fails,
goto err_trig and remove the trigger.
In addition, we also reorder the unwind that goes on in the
remove() callback to match the new ordering.
Fixes: 6dd112b9f8 ("iio: adc: mxs-lradc: Add support for ADC driver")
Signed-off-by: Jiakai Luo <jkluo@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/r/20230422133407.72908-1-jkluo@hust.edu.cn
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 79b8ded9d9 upstream.
When apply_acpi_orientation() fails, st_accel_common_probe() will fall back
to iio_read_mount_matrix(), which checks for a mount-matrix device property
and if that is not set falls back to the identity matrix.
But when a sensor has no ACPI companion fwnode, or when the ACPI fwnode
does not have a "_ONT" method apply_acpi_orientation() was returning 0,
causing iio_read_mount_matrix() to never get called resulting in an
invalid mount_matrix:
[root@fedora ~]# cat /sys/bus/iio/devices/iio\:device0/mount_matrix
(null), (null), (null); (null), (null), (null); (null), (null), (null)
Fix this by making apply_acpi_orientation() always return an error when
it did not set the mount_matrix.
Fixes: 3d8ad94bb1 ("iio: accel: st_sensors: Support generic mounting matrix")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Marius Hoch <mail@mariushoch.de>
Link: https://lore.kernel.org/r/20230416212409.310936-1-hdegoede@redhat.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 81f3affa19 ]
When the uvcvideo driver encounters a format descriptor with an unknown
format GUID, it creates a corresponding struct uvc_format instance with
the fcc field set to 0. Since commit 50459f103e ("media: uvcvideo:
Remove format descriptions"), the driver relies on the V4L2 core to
provide the format description string, which the V4L2 core can't do
without a valid 4CC. This triggers a WARN_ON.
As a format with a zero 4CC can't be selected, it is unusable for
applications. Ignore the format completely without creating a uvc_format
instance, which fixes the warning.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217252
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2180107
Fixes: 50459f103e ("media: uvcvideo: Remove format descriptions")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c26fabe733 ]
Until commit 5c2712387d ("cacheinfo: Fix LLC is not exported through
sysfs"), cacheinfo called populate_cache_leaves() for CPU coming online
which let the arch specific functions handle (at least on x86)
populating the shared_cpu_map. However, with the changes in the
aforementioned commit, populate_cache_leaves() is not called when a CPU
comes online as a result of hotplug since last_level_cache_is_valid()
returns true as the cacheinfo data is not discarded. The CPU coming
online is not present in shared_cpu_map, however, it will not be added
since the cpu_cacheinfo->cpu_map_populated flag is set (it is set in
populate_cache_leaves() when cacheinfo is first populated for x86)
This can lead to inconsistencies in the shared_cpu_map when an offlined
CPU comes online again. Example below depicts the inconsistency in the
shared_cpu_list in cacheinfo when CPU8 is offlined and onlined again on
a 3rd Generation EPYC processor:
# for i in /sys/devices/system/cpu/cpu8/cache/index*/shared_cpu_list; do echo -n "$i: "; cat $i; done
/sys/devices/system/cpu/cpu8/cache/index0/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu8/cache/index1/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu8/cache/index2/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu8/cache/index3/shared_cpu_list: 8-15,136-143
# echo 0 > /sys/devices/system/cpu/cpu8/online
# echo 1 > /sys/devices/system/cpu/cpu8/online
# for i in /sys/devices/system/cpu/cpu8/cache/index*/shared_cpu_list; do echo -n "$i: "; cat $i; done
/sys/devices/system/cpu/cpu8/cache/index0/shared_cpu_list: 8
/sys/devices/system/cpu/cpu8/cache/index1/shared_cpu_list: 8
/sys/devices/system/cpu/cpu8/cache/index2/shared_cpu_list: 8
/sys/devices/system/cpu/cpu8/cache/index3/shared_cpu_list: 8
# cat /sys/devices/system/cpu/cpu136/cache/index0/shared_cpu_list
136
# cat /sys/devices/system/cpu/cpu136/cache/index3/shared_cpu_list
9-15,136-143
Clear the flag when the CPU is removed from shared_cpu_map when
cache_shared_cpu_map_remove() is called during CPU hotplug. This will
allow cache_shared_cpu_map_setup() to add the CPU coming back online in
the shared_cpu_map. Set the flag again when the shared_cpu_map is setup.
Following are results of performing the same test as described above with
the changes:
# for i in /sys/devices/system/cpu/cpu8/cache/index*/shared_cpu_list; do echo -n "$i: "; cat $i; done
/sys/devices/system/cpu/cpu8/cache/index0/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu8/cache/index1/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu8/cache/index2/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu8/cache/index3/shared_cpu_list: 8-15,136-143
# echo 0 > /sys/devices/system/cpu/cpu8/online
# echo 1 > /sys/devices/system/cpu/cpu8/online
# for i in /sys/devices/system/cpu/cpu8/cache/index*/shared_cpu_list; do echo -n "$i: "; cat $i; done
/sys/devices/system/cpu/cpu8/cache/index0/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu8/cache/index1/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu8/cache/index2/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu8/cache/index3/shared_cpu_list: 8-15,136-143
# cat /sys/devices/system/cpu/cpu136/cache/index0/shared_cpu_list
8,136
# cat /sys/devices/system/cpu/cpu136/cache/index3/shared_cpu_list
8-15,136-143
Fixes: 5c2712387d ("cacheinfo: Fix LLC is not exported through sysfs")
Signed-off-by: K Prateek Nayak <kprateek.nayak@amd.com>
Reviewed-by: Yicong Yang <yangyicong@hisilicon.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://lore.kernel.org/r/20230508084115.1157-3-kprateek.nayak@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 126310c9f6 ]
While building the shared_cpu_map, check if the cache level and cache
type matches. On certain systems that build the cache topology based on
the instance ID, there are cases where the same ID may repeat across
multiple cache levels, leading inaccurate topology.
In event of CPU offlining, the cache_shared_cpu_map_remove() does not
consider if IDs at same level are being compared. As a result, when same
IDs repeat across different cache levels, the CPU going offline is not
removed from all the shared_cpu_map.
Below is the output of cache topology of CPU8 and it's SMT sibling after
CPU8 is offlined on a dual socket 3rd Generation AMD EPYC processor
(2 x 64C/128T) running kernel release v6.3:
# for i in /sys/devices/system/cpu/cpu8/cache/index*/shared_cpu_list; do echo -n "$i: "; cat $i; done
/sys/devices/system/cpu/cpu8/cache/index0/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu8/cache/index1/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu8/cache/index2/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu8/cache/index3/shared_cpu_list: 8-15,136-143
# echo 0 > /sys/devices/system/cpu/cpu8/online
# for i in /sys/devices/system/cpu/cpu136/cache/index*/shared_cpu_list; do echo -n "$i: "; cat $i; done
/sys/devices/system/cpu/cpu136/cache/index0/shared_cpu_list: 136
/sys/devices/system/cpu/cpu136/cache/index1/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu136/cache/index2/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu136/cache/index3/shared_cpu_list: 9-15,136-143
CPU8 is removed from index0 (L1i) but remains in the shared_cpu_list of
index1 (L1d) and index2 (L2). Since L1i, L1d, and L2 are shared by the
SMT siblings, and they have the same cache instance ID, CPU 2 is only
removed from the first index with matching ID which is index1 (L1i) in
this case. With this fix, the results are as expected when performing
the same experiment on the same system:
# for i in /sys/devices/system/cpu/cpu8/cache/index*/shared_cpu_list; do echo -n "$i: "; cat $i; done
/sys/devices/system/cpu/cpu8/cache/index0/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu8/cache/index1/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu8/cache/index2/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu8/cache/index3/shared_cpu_list: 8-15,136-143
# echo 0 > /sys/devices/system/cpu/cpu8/online
# for i in /sys/devices/system/cpu/cpu136/cache/index*/shared_cpu_list; do echo -n "$i: "; cat $i; done
/sys/devices/system/cpu/cpu136/cache/index0/shared_cpu_list: 136
/sys/devices/system/cpu/cpu136/cache/index1/shared_cpu_list: 136
/sys/devices/system/cpu/cpu136/cache/index2/shared_cpu_list: 136
/sys/devices/system/cpu/cpu136/cache/index3/shared_cpu_list: 9-15,136-143
When rebuilding topology, the same problem appears as
cache_shared_cpu_map_setup() implements a similar logic. Consider the
same 3rd Generation EPYC processor: CPUs in Core 1, that share the L1
and L2 caches, have L1 and L2 instance ID as 1. For all the CPUs on
the second chiplet, the L3 ID is also 1 leading to grouping on CPUs from
Core 1 (1, 17) and the entire second chiplet (8-15, 24-31) as CPUs
sharing one cache domain. This went undetected since x86 processors
depended on arch specific populate_cache_leaves() method to repopulate
the shared_cpus_map when CPU came back online until kernel release
v6.3-rc5.
Fixes: 198102c910 ("cacheinfo: Fix shared_cpu_map to handle shared caches at different levels")
Signed-off-by: K Prateek Nayak <kprateek.nayak@amd.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://lore.kernel.org/r/20230508084115.1157-2-kprateek.nayak@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8fe72b76db ]
There was a bug where this code forgot to unlock the tdev->mutex if the
kzalloc() failed. Fix this issue, by moving the allocation outside the
lock.
Fixes: 2d1e952a2b ("mailbox: mailbox-test: Fix potential double-free in mbox_test_message_write()")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Lee Jones <lee@kernel.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed17f89e95 ]
When VCODEC_CAPABILITY_4K_DISABLED is not set in dec_capability, skip
formats that are not MTK_FMT_DEC so only decoder formats is updated in
mtk_init_vdec_params.
Fixes: e25528e1db ("media: mediatek: vcodec: Use 4K frame size when supported by stateful decoder")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9f0e3d5a0 ]
The preorder callback on the kvm_pgtable_stage2_map() path can replace
a table with a block, then recursively free the detached table. The
higher-level walking logic stashes the old page table entry and
then walks the freed table, invoking the leaf callback and
potentially freeing pgtable pages prematurely.
In normal operation, the call to tear down the detached stage-2
is indirected and uses an RCU callback to trigger the freeing.
RCU is not available to pKVM, which is where this bug is
triggered.
Change the behavior of the walker to reload the page table entry
after invoking the walker callback on preorder traversal, as it
does for leaf entries.
Tested on Pixel 6.
Fixes: 5c359cca1f ("KVM: arm64: Tear down unlinked stage-2 subtree after break-before-make")
Suggested-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Fuad Tabba <tabba@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230522103258.402272-1-tabba@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c845304d2 ]
After commit b752ea0c28 ("perf/x86/intel/ds: Flush PEBS DS when changing
PEBS_DATA_CFG"), the cpuc->pebs_data_cfg may save some bits that are not
supported by real hardware, such as PEBS_UPDATE_DS_SW. This would cause
the VMX hardware MSR switching mechanism to save/restore invalid values
for PEBS_DATA_CFG MSR, thus crashing the host when PEBS is used for guest.
Fix it by using the active host value from cpuc->active_pebs_data_cfg.
Fixes: b752ea0c28 ("perf/x86/intel/ds: Flush PEBS DS when changing PEBS_DATA_CFG")
Signed-off-by: Like Xu <likexu@tencent.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Link: https://lore.kernel.org/r/20230517133808.67885-1-likexu@tencent.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d54820b22e ]
When target mode is enabled, the pci_irq_get_affinity() function may return
a NULL value in qla_mapq_init_qp_cpu_map() due to the qla24xx_enable_msix()
code that handles IRQ settings for target mode. This leads to a crash due
to a NULL pointer dereference.
This patch fixes the issue by adding a check for the NULL value returned by
pci_irq_get_affinity() and introducing a 'cpu_mapped' boolean flag to the
qla_qpair structure, ensuring that the qpair's CPU affinity is updated when
it has not been mapped to a CPU.
Fixes: 1d201c81d4 ("scsi: qla2xxx: Select qpair depending on which CPU post_cmd() gets called")
Signed-off-by: Gleb Chesnokov <gleb.chesnokov@scst.dev>
Link: https://lore.kernel.org/r/56b416f2-4e0f-b6cf-d6d5-b7c372e3c6a2@scst.dev
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09cce60bdd ]
Since host stage-2 mappings are created lazily, we cannot rely solely on
the pte in order to recover the target physical address when checking a
host-initiated memory transition as this permits donation of unmapped
regions corresponding to MMIO or "no-map" memory.
Instead of inspecting the pte, move the addr_is_allowed_memory() check
into the host callback function where it is passed the physical address
directly from the walker.
Cc: Quentin Perret <qperret@google.com>
Fixes: e82edcc75c ("KVM: arm64: Implement do_share() helper for sharing memory")
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230518095844.1178-1-will@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59112e9c39 ]
Lockdep reports a circular lock dependency between the srcu and the
config_lock:
[ 262.179917] -> #1 (&kvm->srcu){.+.+}-{0:0}:
[ 262.182010] __synchronize_srcu+0xb0/0x224
[ 262.183422] synchronize_srcu_expedited+0x24/0x34
[ 262.184554] kvm_io_bus_register_dev+0x324/0x50c
[ 262.185650] vgic_register_redist_iodev+0x254/0x398
[ 262.186740] vgic_v3_set_redist_base+0x3b0/0x724
[ 262.188087] kvm_vgic_addr+0x364/0x600
[ 262.189189] vgic_set_common_attr+0x90/0x544
[ 262.190278] vgic_v3_set_attr+0x74/0x9c
[ 262.191432] kvm_device_ioctl+0x2a0/0x4e4
[ 262.192515] __arm64_sys_ioctl+0x7ac/0x1ba8
[ 262.193612] invoke_syscall.constprop.0+0x70/0x1e0
[ 262.195006] do_el0_svc+0xe4/0x2d4
[ 262.195929] el0_svc+0x44/0x8c
[ 262.196917] el0t_64_sync_handler+0xf4/0x120
[ 262.198238] el0t_64_sync+0x190/0x194
[ 262.199224]
[ 262.199224] -> #0 (&kvm->arch.config_lock){+.+.}-{3:3}:
[ 262.201094] __lock_acquire+0x2b70/0x626c
[ 262.202245] lock_acquire+0x454/0x778
[ 262.203132] __mutex_lock+0x190/0x8b4
[ 262.204023] mutex_lock_nested+0x24/0x30
[ 262.205100] vgic_mmio_write_v3_misc+0x5c/0x2a0
[ 262.206178] dispatch_mmio_write+0xd8/0x258
[ 262.207498] __kvm_io_bus_write+0x1e0/0x350
[ 262.208582] kvm_io_bus_write+0xe0/0x1cc
[ 262.209653] io_mem_abort+0x2ac/0x6d8
[ 262.210569] kvm_handle_guest_abort+0x9b8/0x1f88
[ 262.211937] handle_exit+0xc4/0x39c
[ 262.212971] kvm_arch_vcpu_ioctl_run+0x90c/0x1c04
[ 262.214154] kvm_vcpu_ioctl+0x450/0x12f8
[ 262.215233] __arm64_sys_ioctl+0x7ac/0x1ba8
[ 262.216402] invoke_syscall.constprop.0+0x70/0x1e0
[ 262.217774] do_el0_svc+0xe4/0x2d4
[ 262.218758] el0_svc+0x44/0x8c
[ 262.219941] el0t_64_sync_handler+0xf4/0x120
[ 262.221110] el0t_64_sync+0x190/0x194
Note that the current report, which can be triggered by the vgic_irq
kselftest, is a triple chain that includes slots_lock, but after
inverting the slots_lock/config_lock dependency, the actual problem
reported above remains.
In several places, the vgic code calls kvm_io_bus_register_dev(), which
synchronizes the srcu, while holding config_lock (#1). And the MMIO
handler takes the config_lock while holding the srcu read lock (#0).
Break dependency #1, by registering the distributor and redistributors
without holding config_lock. The ITS also uses kvm_io_bus_register_dev()
but already relies on slots_lock to serialize calls.
The distributor iodev is created on the first KVM_RUN call. Multiple
threads will race for vgic initialization, and only the first one will
see !vgic_ready() under the lock. To serialize those threads, rely on
slots_lock rather than config_lock.
Redistributors are created earlier, through KVM_DEV_ARM_VGIC_GRP_ADDR
ioctls and vCPU creation. Similarly, serialize the iodev creation with
slots_lock, and the rest with config_lock.
Fixes: f003277311 ("KVM: arm64: Use config_lock to protect vgic state")
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230518100914.2837292-2-jean-philippe@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20f291b88e ]
The problem is these lines:
ret = vref_uv = regulator_get_voltage(adc->vref);
if (ret < 0)
The "ret" variable is type long and "vref_uv" is u32 so that means
the condition can never be true on a 64bit system. A negative error
code from regulator_get_voltage() would be cast to a high positive
u32 value and then remain a high positive value when cast to a long.
The "ret" variable only ever stores ints so it should be declared as
an int. We can delete the "vref_uv" variable and use "ret" directly.
Fixes: 7d02296ac8 ("iio: adc: add imx93 adc support")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/Y+utEvjfjQRQo2QB@kili
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69baa3a623 ]
User should not be able to write block device if it is read-only at
block level (e.g force_ro attribute). This is ensured in the regular
fops write operation (blkdev_write_iter) but not when writing via
user mapping (mmap), allowing user to actually write a read-only
block device via a PROT_WRITE mapping.
Example: This can lead to integrity issue of eMMC boot partition
(e.g mmcblk0boot0) which is read-only by default.
To fix this issue, simply deny shared writable mapping if the block
is readonly.
Note: Block remains writable if switch to read-only is performed
after the initial mapping, but this is expected behavior according
to commit a32e236eb9 ("Partially revert "block: fail op_is_write()
requests to read-only partitions"")'.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230510074223.991297-1-loic.poulain@linaro.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0649728123 ]
Add a quirk for Teamgroup MP33 that reports duplicate ids for disk.
Signed-off-by: Daniel Smith <dansmith@ds.gy>
[kch: patch formatting]
Signed-off-by: Chaitanya Kulkarni <kch@nvidia.com>
Tested-by: Daniel Smith <dansmith@ds.gy>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1a322a7a4 ]
When performing device unbind or halt, we have disabled all irqs at the
very begining like amdgpu_pci_remove or amdgpu_device_halt. So
amdgpu_irq_put for irqs stored in fence driver should not be called
any more, otherwise, below calltrace will arrive.
[ 139.114088] WARNING: CPU: 2 PID: 1550 at drivers/gpu/drm/amd/amdgpu/amdgpu_irq.c:616 amdgpu_irq_put+0xf6/0x110 [amdgpu]
[ 139.114655] Call Trace:
[ 139.114655] <TASK>
[ 139.114657] amdgpu_fence_driver_hw_fini+0x93/0x130 [amdgpu]
[ 139.114836] amdgpu_device_fini_hw+0xb6/0x350 [amdgpu]
[ 139.114955] amdgpu_driver_unload_kms+0x51/0x70 [amdgpu]
[ 139.115075] amdgpu_pci_remove+0x63/0x160 [amdgpu]
[ 139.115193] ? __pm_runtime_resume+0x64/0x90
[ 139.115195] pci_device_remove+0x3a/0xb0
[ 139.115197] device_remove+0x43/0x70
[ 139.115198] device_release_driver_internal+0xbd/0x140
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb1b7be9b1 ]
When CONFIG_PROC_FS is disabled, the function declarations for some
procfs functions are hidden, but the definitions are still build,
as shown by this compiler warning:
net/atm/resources.c:403:7: error: no previous prototype for 'atm_dev_seq_start' [-Werror=missing-prototypes]
net/atm/resources.c:409:6: error: no previous prototype for 'atm_dev_seq_stop' [-Werror=missing-prototypes]
net/atm/resources.c:414:7: error: no previous prototype for 'atm_dev_seq_next' [-Werror=missing-prototypes]
Add another #ifdef to leave these out of the build.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230516194625.549249-2-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 040b5a046a ]
Two functions are defined and used in pcm_oss.c but also optionally
used from io.c, with an optional prototype. If CONFIG_SND_PCM_OSS_PLUGINS
is disabled, this causes a warning as the functions are not static
and have no prototype:
sound/core/oss/pcm_oss.c:1235:19: error: no previous prototype for 'snd_pcm_oss_write3' [-Werror=missing-prototypes]
sound/core/oss/pcm_oss.c:1266:19: error: no previous prototype for 'snd_pcm_oss_read3' [-Werror=missing-prototypes]
Avoid this by making the prototypes unconditional.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230516195046.550584-2-arnd@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2eb94dd56a ]
If a userspace application performes a "delete_controller" command
early during the ctrl initialization, the delete operation
may race against the init code and the kernel will crash.
nvme nvme5: Connect command failed: host path error
nvme nvme5: failed to connect queue: 0 ret=880
PF: supervisor write access in kernel mode
PF: error_code(0x0002) - not-present page
blk_mq_quiesce_queue+0x18/0x90
nvme_tcp_delete_ctrl+0x24/0x40 [nvme_tcp]
nvme_do_delete_ctrl+0x7f/0x8b [nvme_core]
nvme_sysfs_delete.cold+0x8/0xd [nvme_core]
kernfs_fop_write_iter+0x124/0x1b0
new_sync_write+0xff/0x190
vfs_write+0x1ef/0x280
Fix the crash by checking the NVME_CTRL_STARTED_ONCE bit;
if it's not set it means that the nvme controller is still
in the process of getting initialized and the kernel
will return an -EBUSY error to userspace.
Set the NVME_CTRL_STARTED_ONCE later in the nvme_start_ctrl()
function, after the controller start operation is completed.
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1743e5f600 ]
nvme_mpath_remove_disk is called after del_gendisk, at which point a
blk_mark_disk_dead call doesn't make any sense.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 224a876e37 ]
gcc with W=1 and ! CONFIG_NF_NAT
net/netfilter/nf_conntrack_netlink.c:3463:32: error:
‘exp_nat_nla_policy’ defined but not used [-Werror=unused-const-variable=]
3463 | static const struct nla_policy exp_nat_nla_policy[CTA_EXPECT_NAT_MAX+1] = {
| ^~~~~~~~~~~~~~~~~~
net/netfilter/nf_conntrack_netlink.c:2979:33: error:
‘any_addr’ defined but not used [-Werror=unused-const-variable=]
2979 | static const union nf_inet_addr any_addr;
| ^~~~~~~~
These variables use is controlled by CONFIG_NF_NAT, so should their definitions.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab87603b25 ]
When the system attempts to sleep while mtk_t7xx is not ready, the driver
cannot put the device to sleep:
[ 12.472918] mtk_t7xx 0000:57:00.0: [PM] Exiting suspend, modem in invalid state
[ 12.472936] mtk_t7xx 0000:57:00.0: PM: pci_pm_suspend(): t7xx_pci_pm_suspend+0x0/0x20 [mtk_t7xx] returns -14
[ 12.473678] mtk_t7xx 0000:57:00.0: PM: dpm_run_callback(): pci_pm_suspend+0x0/0x1b0 returns -14
[ 12.473711] mtk_t7xx 0000:57:00.0: PM: failed to suspend async: error -14
[ 12.764776] PM: Some devices failed to suspend, or early wake event detected
Mediatek confirmed the device can take a rather long time to complete
its initialization, so wait for up to 20 seconds until init is done.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 212457ccbd ]
clang warns about an unpacked structure inside of a packed one:
drivers/net/wireless/broadcom/b43/b43.h:654:4: error: field data within 'struct b43_iv' is less aligned than 'union (unnamed union at /home/arnd/arm-soc/drivers/net/wireless/broadcom/b43/b43.h:651:2)' and is usually due to 'struct b43_iv' being packed, which can lead to unaligned accesses [-Werror,-Wunaligned-access]
The problem here is that the anonymous union has the default alignment
from its members, apparently because the original author mixed up the
placement of the __packed attribute by placing it next to the struct
member rather than the union definition. As the struct itself is
also marked as __packed, there is no need to mark its members, so just
move the annotation to the inner type instead.
As Michael noted, the same problem is present in b43legacy, so
change both at the same time.
Acked-by: Michael Büsch <m@bues.ch>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Link: https://lore.kernel.org/oe-kbuild-all/202305160749.ay1HAoyP-lkp@intel.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230516183442.536589-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04312de4ce ]
When we allocate a new channel context, or find an existing one
that is compatible, we currently assign it to a link before its
mindef is updated. This leads to strange situations, especially
in link switching where you switch to an 80 MHz link and expect
it to be active immediately, but the mindef is still configured
to 20 MHz while assigning. Also, it's strange that the chandef
passed to the assign method's argument is wider than the one in
the context.
Fix this by calculating the mindef with the new link considered
before calling the driver.
In particular, this fixes an iwlwifi problem during link switch
where the firmware would assert because the (link) station that
was added for the AP is configured to transmit at a bandwidth
that's wider than the channel context that it's configured on.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230504134511.828474-5-gregory.greenman@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b72a455a24 ]
When a chanctx is reserved for a new vif and we recalculate
the minimal definition for it, we need to consider the new
interface it's being reserved for before we assign it, so it
can be used directly with the correct min channel width.
Fix the code to - optionally - consider that, and use that
option just before doing the reassignment.
Also, when considering channel context reservations, we
should only consider the one link we're currently working with.
Change the boolean argument to a link pointer to do that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230504134511.828474-4-gregory.greenman@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20429444e6 ]
When using rtl8192cu with rtl8xxxu driver to connect wifi, there is a
probability of failure, which shows "authentication with ... timed out".
Through debugging, it was found that the RCR register has been inexplicably
modified to an incorrect value, resulting in the nic not being able to
receive authenticated frames.
To fix this problem, add regrcr in rtl8xxxu_priv struct, and store
the RCR value every time the register is written, and use it the next
time the register need to be modified.
Signed-off-by: Yun Lu <luyun@kylinos.cn>
Link: https://lore.kernel.org/all/20230427020512.1221062-1-luyun_611@163.com
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230512012055.2990472-1-luyun_611@163.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2facd5d398 ]
The pointer to IPL Parameter Information Block is stored
in the absolute lowcore for later use by dump tools. That
pointer is a virtual address, though it should be physical
instead.
Note, this does not fix a real issue, since virtual and
physical addresses are currently the same.
Suggested-by: Heiko Carstens <hca@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a33239be2d ]
When SMT thread CPUs are added to CPU masks the nr_cpu_ids
limit is not checked and could be exceeded. This leads to
a warning for example if CONFIG_DEBUG_PER_CPU_MAPS is set
and the command line parameter nr_cpus is set to 1.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 844cf829e5 ]
Key blobs for the IOCTLs PKEY_KBLOB2PROTK[23] may contain clear key
material. Zeroize the copies of these keys in kernel memory after
creating the protected key.
Reviewed-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Holger Dengler <dengler@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3de975862f ]
When a firmware IPC error happens during a pm_runtime suspend, we
ignore the error and suspend anyways. However, the code
unconditionally increases the runtime_pm counter. This results in a
confusing configuration where the code will suspend, resume but never
suspend again due to the use of pm_runtime_get_noresume().
The intent of the counter increase was to prevent entry in D3, but if
that transition to D3 is already started it cannot be stopped. In
addition, there's no point in that case in trying to prevent anything,
the firmware error is handled and the next resume will re-initialize
the firmware completely.
This patch changes the logic to prevent suspend when the device is
pm_runtime active and has a use_count > 0.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com
Link: https://lore.kernel.org/r/20230512103315.8921-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 280a8ab817 ]
If the device node of dvb_ca_en50221 is open() and the
device is disconnected, a UAF may occur when calling
close() on the device node.
The root cause is that wake_up() and wait_event() for
dvbdev->wait_queue are not implemented.
So implement wait_event() function in dvb_ca_en50221_release()
and add 'remove_mutex' which prevents race condition
for 'ca->exit'.
[mchehab: fix a checkpatch warning]
Link: https://lore.kernel.org/linux-media/20221121063308.GA33821@ubuntu
Signed-off-by: Hyunwoo Kim <v4bel@theori.io>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 627bb528b0 ]
dvb_register_device() dynamically allocates fops with kmemdup()
to set the fops->owner.
And these fops are registered in 'file->f_ops' using replace_fops()
in the dvb_device_open() process, and kfree()d in dvb_free_device().
However, it is not common to use dynamically allocated fops instead
of 'static const' fops as an argument of replace_fops(),
and UAF may occur.
These UAFs can occur on any dvb type using dvb_register_device(),
such as dvb_dvr, dvb_demux, dvb_frontend, dvb_net, etc.
So, instead of kfree() the fops dynamically allocated in
dvb_register_device() in dvb_free_device() called during the
.disconnect() process, kfree() it collectively in exit_dvbdev()
called when the dvbdev.c module is removed.
Link: https://lore.kernel.org/linux-media/20221117045925.14297-4-imv4bel@gmail.com
Signed-off-by: Hyunwoo Kim <imv4bel@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4172385b0c ]
A race condition may occur between the .disconnect function, which
is called when the device is disconnected, and the dvb_device_open()
function, which is called when the device node is open()ed.
This results in several types of UAFs.
The root cause of this is that you use the dvb_device_open() function,
which does not implement a conditional statement
that checks 'dvbnet->exit'.
So, add 'remove_mutex` to protect 'dvbnet->exit' and use
locked_dvb_net_open() function to check 'dvbnet->exit'.
[mchehab: fix a checkpatch warning]
Link: https://lore.kernel.org/linux-media/20221117045925.14297-3-imv4bel@gmail.com
Signed-off-by: Hyunwoo Kim <imv4bel@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6769a0b7ee ]
If the device node of dvb_frontend is open() and the device is
disconnected, many kinds of UAFs may occur when calling close()
on the device node.
The root cause of this is that wake_up() for dvbdev->wait_queue
is implemented in the dvb_frontend_release() function, but
wait_event() is not implemented in the dvb_frontend_stop() function.
So, implement wait_event() function in dvb_frontend_stop() and
add 'remove_mutex' which prevents race condition for 'fe->exit'.
[mchehab: fix a couple of checkpatch warnings and some mistakes at the error handling logic]
Link: https://lore.kernel.org/linux-media/20221117045925.14297-2-imv4bel@gmail.com
Signed-off-by: Hyunwoo Kim <imv4bel@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae11c0efae ]
The driver will match mostly by DT table (even thought there is regular
ID table) so there is little benefit in of_match_ptr (this also allows
ACPI matching via PRP0001, even though it might not be relevant here).
This also fixes !CONFIG_OF error:
drivers/media/dvb-frontends/mn88443x.c:782:34: error: ‘mn88443x_of_match’ defined but not used [-Werror=unused-const-variable=]
Link: https://lore.kernel.org/linux-media/20230312131318.351173-28-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 517a281338 ]
Since dvb_frontend_detach() is not called in ttusb_dec_exit_dvb(),
which is called when the device is disconnected, dvb_frontend_free()
is not finally called.
This causes a memory leak just by repeatedly plugging and
unplugging the device.
Fix this issue by adding dvb_frontend_detach() to ttusb_dec_exit_dvb().
Link: https://lore.kernel.org/linux-media/20221117045925.14297-5-imv4bel@gmail.com
Signed-off-by: Hyunwoo Kim <imv4bel@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a4315e5be7 ]
The function of "dvb_ca_en50221_write_data" at source/drivers/media
/dvb-core/dvb_ca_en50221.c is used for two cases.
The first case is for writing APDU data in the function of
"dvb_ca_en50221_io_write" at source/drivers/media/dvb-core/
dvb_ca_en50221.c.
The second case is for writing the host link buf size on the
Command Register in the function of "dvb_ca_en50221_link_init"
at source/drivers/media/dvb-core/dvb_ca_en50221.c.
In the second case, there exists a bug like following.
In the function of the "dvb_ca_en50221_link_init",
after a TV host calculates the host link buf_size,
the TV host writes the calculated host link buf_size on the
Size Register.
Accroding to the en50221 Spec (the page 60 of
https://dvb.org/wp-content/uploads/2020/02/En50221.V1.pdf),
before this writing operation, the "SW(CMDREG_SW)" flag in the
Command Register should be set. We can see this setting operation
in the function of the "dvb_ca_en50221_link_init" like below.
...
if ((ret = ca->pub->write_cam_control(ca->pub, slot,
CTRLIF_COMMAND, IRQEN | CMDREG_SW)) != 0)
return ret;
...
But, after that, the real writing operation is implemented using
the function of the "dvb_ca_en50221_write_data" in the function of
"dvb_ca_en50221_link_init", and the "dvb_ca_en50221_write_data"
includes the function of "ca->pub->write_cam_control",
and the function of the "ca->pub->write_cam_control" in the
function of the "dvb_ca_en50221_wrte_data" does not include
"CMDREG_SW" flag like below.
...
if ((status = ca->pub->write_cam_control(ca->pub, slot,
CTRLIF_COMMAND, IRQEN | CMDREG_HC)) != 0)
...
In the above source code, we can see only the "IRQEN | CMDREG_HC",
but we cannot see the "CMDREG_SW".
The "CMDREG_SW" flag which was set in the function of the
"dvb_ca_en50221_link_init" was rollbacked by the follwoing function
of the "dvb_ca_en50221_write_data".
This is a bug. and this bug causes that the calculated host link buf_size
is not properly written in the CI module.
Through this patch, we fix this bug.
Link: https://lore.kernel.org/linux-media/20220818125027.1131-1-yongsuyoo0215@gmail.com
Signed-off-by: YongSu Yoo <yongsuyoo0215@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ded5bd2a4 ]
In digitv_i2c_xfer, msg is controlled by user. When msg[i].buf
is null and msg[i].len is zero, former checks on msg[i].buf would be
passed. Malicious data finally reach digitv_i2c_xfer. If accessing
msg[i].buf[0] without sanity check, null ptr deref would happen. We add
check on msg[i].len to prevent crash.
Similar commit:
commit 0ed554fd76 ("media: dvb-usb: az6027: fix null-ptr-deref in az6027_i2c_xfer()")
Link: https://lore.kernel.org/linux-media/20230313095008.1039689-1-harperchen1110@gmail.com
Signed-off-by: Wei Chen <harperchen1110@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa4a447b81 ]
In rtl28xxu_i2c_xfer, msg is controlled by user. When msg[i].buf
is null and msg[i].len is zero, former checks on msg[i].buf would be
passed. Malicious data finally reach rtl28xxu_i2c_xfer. If accessing
msg[i].buf[0] without sanity check, null ptr deref would happen.
We add check on msg[i].len to prevent crash.
Similar commit:
commit 0ed554fd76
("media: dvb-usb: az6027: fix null-ptr-deref in az6027_i2c_xfer()")
Link: https://lore.kernel.org/linux-media/tencent_3623572106754AC2F266B316798B0F6CCA05@qq.com
Signed-off-by: Zhang Shurong <zhang_shurong@foxmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dff9190901 ]
In ce6230_i2c_master_xfer, msg is controlled by user. When msg[i].buf
is null and msg[i].len is zero, former checks on msg[i].buf would be
passed. Malicious data finally reach ce6230_i2c_master_xfer. If accessing
msg[i].buf[0] without sanity check, null ptr deref would happen. We add
check on msg[i].len to prevent crash.
Similar commit:
commit 0ed554fd76 ("media: dvb-usb: az6027: fix null-ptr-deref in az6027_i2c_xfer()")
Link: https://lore.kernel.org/linux-media/20230313092751.209496-1-harperchen1110@gmail.com
Signed-off-by: Wei Chen <harperchen1110@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7efb10d8dc ]
In dvb_demux.c, some logics exist which compare the expected
continuity counter and the real continuity counter. If they
are not matched each other, both of the expected continuity
counter and the real continuity counter should be printed.
But there exists a bug that the expected continuity counter
is not correctly printed. The expected continuity counter is
replaced with the real countinuity counter + 1 so that
the epected continuity counter is not correclty printed.
This is wrong. This bug is fixed.
Link: https://lore.kernel.org/linux-media/20230305212519.499-1-yongsuyoo0215@gmail.com
Signed-off-by: YongSu Yoo <yongsuyoo0215@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f63550e2b1 ]
Apply a workaround for what appears to be a hardware quirk.
The problem seems to happen when enabling "whole chip power" (bit D7
register R6) for the very first time after the chip receives power. If
either "output" (D4) or "DAC" (D3) aren't powered on at that time,
playback becomes very distorted later on.
This happens on the Google Chameleon v3, as well as on a ZYBO Z7-10:
https://ez.analog.com/audio/f/q-a/543726/solved-ssm2603-right-output-offset-issue/480229
I suspect this happens only when using an external MCLK signal (which
is the case for both of these boards).
Here are some experiments run on a Google Chameleon v3. These were run
in userspace using a wrapper around the i2cset utility:
ssmset() {
i2cset -y 0 0x1a $(($1*2)) $2
}
For each of the following sequences, we apply power to the ssm2603
chip, set the configuration registers R0-R5 and R7-R8, run the selected
sequence, and check for distortions on playback.
ssmset 0x09 0x01 # core
ssmset 0x06 0x07 # chip, out, dac
OK
ssmset 0x09 0x01 # core
ssmset 0x06 0x87 # out, dac
ssmset 0x06 0x07 # chip
OK
(disable MCLK)
ssmset 0x09 0x01 # core
ssmset 0x06 0x1f # chip
ssmset 0x06 0x07 # out, dac
(enable MCLK)
OK
ssmset 0x09 0x01 # core
ssmset 0x06 0x1f # chip
ssmset 0x06 0x07 # out, dac
NOT OK
ssmset 0x06 0x1f # chip
ssmset 0x09 0x01 # core
ssmset 0x06 0x07 # out, dac
NOT OK
ssmset 0x09 0x01 # core
ssmset 0x06 0x0f # chip, out
ssmset 0x06 0x07 # dac
NOT OK
ssmset 0x09 0x01 # core
ssmset 0x06 0x17 # chip, dac
ssmset 0x06 0x07 # out
NOT OK
For each of the following sequences, we apply power to the ssm2603
chip, run the selected sequence, issue a reset with R15, configure
R0-R5 and R7-R8, run one of the NOT OK sequences from above, and check
for distortions.
ssmset 0x09 0x01 # core
ssmset 0x06 0x07 # chip, out, dac
OK
(disable MCLK)
ssmset 0x09 0x01 # core
ssmset 0x06 0x07 # chip, out, dac
(enable MCLK after reset)
NOT OK
ssmset 0x09 0x01 # core
ssmset 0x06 0x17 # chip, dac
NOT OK
ssmset 0x09 0x01 # core
ssmset 0x06 0x0f # chip, out
NOT OK
ssmset 0x06 0x07 # chip, out, dac
NOT OK
Signed-off-by: Paweł Anikiel <pan@semihalf.com
Link: https://lore.kernel.org/r/20230508113037.137627-8-pan@semihalf.com
Signed-off-by: Mark Brown <broonie@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad721bc919 ]
When the CPU supplies bit/frame clocks, the system clock (clk_i2s)
is divided to produce the bit clock. This is a simple 1/N divider
with a fairly limited range, so for a given system clock frequency
only a few sample rates can be produced. Usually a wider range of
sample rates is supported by varying the system clock frequency.
The old calculation method was not very robust and could easily
produce the wrong clock rate, especially with non-standard rates.
For example, if the system clock is 1.99x the target bit clock
rate, the divider would be calculated as 1 instead of the more
accurate 2.
Instead, use a more accurate method that considers two adjacent
divider settings and selects the one that produces the least error
versus the requested rate. If the error is 5% or higher then the
rate setting is rejected to prevent garbled audio.
Skip divider calculation when the codec is supplying both the bit
and frame clock; in that case, the divider outputs are unused and
we don't want to constrain the sample rate.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com
Link: https://lore.kernel.org/r/20230509125134.208129-1-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8680407b6f ]
This change ensures that if configured in the policy, the if_id set in
the policy and secpath states match during the inbound policy check.
Without this, there is potential for ambiguity where entries in the
secpath differing by only the if_id could be mismatched.
Notably, this is checked in the outbound direction when resolving
templates to SAs, but not on the inbound path when matching SAs and
policies.
Test: Tested against Android kernel unit tests & CTS
Signed-off-by: Benedict Wong <benedictwong@google.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73a23d7710 ]
Since we no longer (want to) export any libc symbols the
_user portions of any drivers need to be built into image
rather than the module. I missed this for the watchdog.
Fix the watchdog accordingly.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e652be0f59 ]
The sysfs_get_enabled() opened file processor not closed,
may cause a file handle leak.
Putting error handling and resource cleanup code together
makes the code easy to maintain and read.
Removed the unnecessary else if branch from the original
function, as it should return an error in cases other than '0'.
Signed-off-by: Hao Zeng <zenghao@kylinos.cn>
Suggested-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3710e2b056 ]
When running the fio test on a 448-core AMD server + a NVME disk,
a soft lockup or a hard lockup call trace is shown:
[soft lockup]
watchdog: BUG: soft lockup - CPU#126 stuck for 23s! [swapper/126:0]
RIP: 0010:_raw_spin_unlock_irqrestore+0x21/0x50
...
Call Trace:
<IRQ>
fq_flush_timeout+0x7d/0xd0
? __pfx_fq_flush_timeout+0x10/0x10
call_timer_fn+0x2e/0x150
run_timer_softirq+0x48a/0x560
? __pfx_fq_flush_timeout+0x10/0x10
? clockevents_program_event+0xaf/0x130
__do_softirq+0xf1/0x335
irq_exit_rcu+0x9f/0xd0
sysvec_apic_timer_interrupt+0xb4/0xd0
</IRQ>
<TASK>
asm_sysvec_apic_timer_interrupt+0x1f/0x30
...
Obvisouly, fq_flush_timeout spends over 20 seconds. Here is ftrace log:
| fq_flush_timeout() {
| fq_ring_free() {
| put_pages_list() {
0.170 us | free_unref_page_list();
0.810 us | }
| free_iova_fast() {
| free_iova() {
* 85622.66 us | _raw_spin_lock_irqsave();
2.860 us | remove_iova();
0.600 us | _raw_spin_unlock_irqrestore();
0.470 us | lock_info_report();
2.420 us | free_iova_mem.part.0();
* 85638.27 us | }
* 85638.84 us | }
| put_pages_list() {
0.230 us | free_unref_page_list();
0.470 us | }
... ...
$ 31017069 us | }
Most of cores are under lock contention for acquiring iova_rbtree_lock due
to the iova flush queue mechanism.
[hard lockup]
NMI watchdog: Watchdog detected hard LOCKUP on cpu 351
RIP: 0010:native_queued_spin_lock_slowpath+0x2d8/0x330
Call Trace:
<IRQ>
_raw_spin_lock_irqsave+0x4f/0x60
free_iova+0x27/0xd0
free_iova_fast+0x4d/0x1d0
fq_ring_free+0x9b/0x150
iommu_dma_free_iova+0xb4/0x2e0
__iommu_dma_unmap+0x10b/0x140
iommu_dma_unmap_sg+0x90/0x110
dma_unmap_sg_attrs+0x4a/0x50
nvme_unmap_data+0x5d/0x120 [nvme]
nvme_pci_complete_batch+0x77/0xc0 [nvme]
nvme_irq+0x2ee/0x350 [nvme]
? __pfx_nvme_pci_complete_batch+0x10/0x10 [nvme]
__handle_irq_event_percpu+0x53/0x1a0
handle_irq_event_percpu+0x19/0x60
handle_irq_event+0x3d/0x60
handle_edge_irq+0xb3/0x210
__common_interrupt+0x7f/0x150
common_interrupt+0xc5/0xf0
</IRQ>
<TASK>
asm_common_interrupt+0x2b/0x40
...
ftrace shows fq_ring_free spends over 10 seconds [1]. Again, most of
cores are under lock contention for acquiring iova_rbtree_lock due
to the iova flush queue mechanism.
[Root Cause]
The root cause is that the max_hw_sectors_kb of nvme disk (mdts=10)
is 4096kb, which streaming DMA mappings cannot benefit from the
scalable IOVA mechanism introduced by the commit 9257b4a206
("iommu/iova: introduce per-cpu caching to iova allocation") if
the length is greater than 128kb.
To fix the lock contention issue, clamp max_hw_sectors based on
DMA optimized limitation in order to leverage scalable IOVA mechanism.
Note: The issue does not happen with another NVME disk (mdts = 5
and max_hw_sectors_kb = 128)
[1] https://gist.github.com/AdrianHuang/bf8ec7338204837631fbdaed25d19cc4
Suggested-by: Keith Busch <kbusch@kernel.org>
Reported-and-tested-by: Jiwei Sun <sunjw10@lenovo.com>
Signed-off-by: Adrian Huang <ahuang12@lenovo.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd375feeaf ]
On Kingston KC3000 and Kingston FURY Renegade (both have the same PCI
IDs) accessing temp3_{min,max} fails with an invalid field error (note
that there is no problem setting the thresholds for temp1).
This contradicts the NVM Express Base Specification 2.0b, page 292:
The over temperature threshold and under temperature threshold
features shall be implemented for all implemented temperature sensors
(i.e., all Temperature Sensor fields that report a non-zero value).
Define NVME_QUIRK_NO_SECONDARY_TEMP_THRESH that disables the thresholds
for all but the composite temperature and set it for this device.
Signed-off-by: Hristo Venev <hristo@venev.name>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0bdf1ad8d1 ]
Minor fix to reset the info field to NULL in case of error.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c75f5a5506 ]
A use-after-free bug may occur if init_imstt invokes framebuffer_release
and free the info ptr. The caller, imsttfb_probe didn't notice that and
still keep the ptr as private data in pdev.
If we remove the driver which will call imsttfb_remove to make cleanup,
UAF happens.
Fix it by return error code if bad case happens in init_imstt.
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 476ac50fc3 ]
Update the maximum resolution reported for HEVC encoding on VCN 3
devices to reflect its 8K encoding capability.
v2: Also update the max height for H.264 encoding to match spec.
(Ruijing)
Signed-off-by: Thong Thai <thong.thai@amd.com>
Reviewed-by: Ruijing Dong <ruijing.dong@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 504a10d9e4 ]
On corrupt gfs2 file systems the evict code can try to reference the
journal descriptor structure, jdesc, after it has been freed and set to
NULL. The sequence of events is:
init_journal()
...
fail_jindex:
gfs2_jindex_free(sdp); <------frees journals, sets jdesc = NULL
if (gfs2_holder_initialized(&ji_gh))
gfs2_glock_dq_uninit(&ji_gh);
fail:
iput(sdp->sd_jindex); <--references jdesc in evict_linked_inode
evict()
gfs2_evict_inode()
evict_linked_inode()
ret = gfs2_trans_begin(sdp, 0, sdp->sd_jdesc->jd_blocks);
<------references the now freed/zeroed sd_jdesc pointer.
The call to gfs2_trans_begin is done because the truncate_inode_pages
call can cause gfs2 events that require a transaction, such as removing
journaled data (jdata) blocks from the journal.
This patch fixes the problem by adding a check for sdp->sd_jdesc to
function gfs2_evict_inode. In theory, this should only happen to corrupt
gfs2 file systems, when gfs2 detects the problem, reports it, then tries
to evict all the system inodes it has read in up to that point.
Reported-by: Yang Lan <lanyang0908@gmail.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e10707d586 ]
When adding proper support for V4L2_FIELD_ALTERNATE it was missed that
this field format should trigger an interrupt for each field, not just
for the whole frame. Fix this by marking it as progressive in the
capture setup, which will then select the correct interrupt mode.
Tested on both Gen2 and Gen3 with the result of a doubling of the frame
rate for V4L2_FIELD_ALTERNATE. From a PAL video source the frame rate is
now 50, which is expected for alternate field capture.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b752ea0c28 ]
Several similar kernel warnings can be triggered,
[56605.607840] CPU0 PEBS record size 0, expected 32, config 0 cpuc->record_size=208
when the below commands are running in parallel for a while on SPR.
while true;
do
perf record --no-buildid -a --intr-regs=AX \
-e cpu/event=0xd0,umask=0x81/pp \
-c 10003 -o /dev/null ./triad;
done &
while true;
do
perf record -o /tmp/out -W -d \
-e '{ld_blocks.store_forward:period=1000000, \
MEM_TRANS_RETIRED.LOAD_LATENCY:u:precise=2:ldlat=4}' \
-c 1037 ./triad;
done
The triad program is just the generation of loads/stores.
The warnings are triggered when an unexpected PEBS record (with a
different config and size) is found.
A system-wide PEBS event with the large PEBS config may be enabled
during a context switch. Some PEBS records for the system-wide PEBS
may be generated while the old task is sched out but the new one
hasn't been sched in yet. When the new task is sched in, the
cpuc->pebs_record_size may be updated for the per-task PEBS events. So
the existing system-wide PEBS records have a different size from the
later PEBS records.
The PEBS buffer should be flushed right before the hardware is
reprogrammed. The new size and threshold should be updated after the
old buffer has been flushed.
Reported-by: Stephane Eranian <eranian@google.com>
Suggested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20230421184529.3320912-1-kan.liang@linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa3eeb638d ]
When unwind instruction is 0xb2,the subsequent instructions
are uleb128 bytes.
For now,it uses only the first uleb128 byte in code.
For vsp increments of 0x204~0x400,use one uleb128 byte like below:
0xc06a00e4 <unwind_test_work>: 0x80b27fac
Compact model index: 0
0xb2 0x7f vsp = vsp + 1024
0xac pop {r4, r5, r6, r7, r8, r14}
For vsp increments larger than 0x400,use two uleb128 bytes like below:
0xc06a00e4 <unwind_test_work>: @0xc0cc9e0c
Compact model index: 1
0xb2 0x81 0x01 vsp = vsp + 1032
0xac pop {r4, r5, r6, r7, r8, r14}
The unwind works well since the decoded uleb128 byte is also 0x81.
For vsp increments larger than 0x600,use two uleb128 bytes like below:
0xc06a00e4 <unwind_test_work>: @0xc0cc9e0c
Compact model index: 1
0xb2 0x81 0x02 vsp = vsp + 1544
0xac pop {r4, r5, r6, r7, r8, r14}
In this case,the decoded uleb128 result is 0x101(vsp=0x204+(0x101<<2)).
While the uleb128 used in code is 0x81(vsp=0x204+(0x81<<2)).
The unwind aborts at this frame since it gets incorrect vsp.
To fix this,add uleb128 decode to cover all the above case.
Signed-off-by: Haibo Li <haibo.li@mediatek.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ae5afd02a ]
If the sibling keys check fails before we move keys from one sibling
leaf to another, we are not aborting the transaction - we leave that to
some higher level caller of btrfs_search_slot() (or anything else that
uses it to insert items into a b+tree).
This means that the transaction abort will provide a stack trace that
omits the b+tree modification call chain. So change this to immediately
abort the transaction and therefore get a more useful stack trace that
shows us the call chain in the bt+tree modification code.
It's also important to immediately abort the transaction just in case
some higher level caller is not doing it, as this indicates a very
serious corruption and we should stop the possibility of doing further
damage.
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d1e952a2b ]
If a user can make copy_from_user() fail, there is a potential for
UAF/DF due to a lack of locking around the allocation, use and freeing
of the data buffers.
This issue is not theoretical. I managed to author a POC for it:
BUG: KASAN: double-free in kfree+0x5c/0xac
Free of addr ffff29280be5de00 by task poc/356
CPU: 1 PID: 356 Comm: poc Not tainted 6.1.0-00001-g961aa6552c04-dirty #20
Hardware name: linux,dummy-virt (DT)
Call trace:
dump_backtrace.part.0+0xe0/0xf0
show_stack+0x18/0x40
dump_stack_lvl+0x64/0x80
print_report+0x188/0x48c
kasan_report_invalid_free+0xa0/0xc0
____kasan_slab_free+0x174/0x1b0
__kasan_slab_free+0x18/0x24
__kmem_cache_free+0x130/0x2e0
kfree+0x5c/0xac
mbox_test_message_write+0x208/0x29c
full_proxy_write+0x90/0xf0
vfs_write+0x154/0x440
ksys_write+0xcc/0x180
__arm64_sys_write+0x44/0x60
invoke_syscall+0x60/0x190
el0_svc_common.constprop.0+0x7c/0x160
do_el0_svc+0x40/0xf0
el0_svc+0x2c/0x6c
el0t_64_sync_handler+0xf4/0x120
el0t_64_sync+0x18c/0x190
Allocated by task 356:
kasan_save_stack+0x3c/0x70
kasan_set_track+0x2c/0x40
kasan_save_alloc_info+0x24/0x34
__kasan_kmalloc+0xb8/0xc0
kmalloc_trace+0x58/0x70
mbox_test_message_write+0x6c/0x29c
full_proxy_write+0x90/0xf0
vfs_write+0x154/0x440
ksys_write+0xcc/0x180
__arm64_sys_write+0x44/0x60
invoke_syscall+0x60/0x190
el0_svc_common.constprop.0+0x7c/0x160
do_el0_svc+0x40/0xf0
el0_svc+0x2c/0x6c
el0t_64_sync_handler+0xf4/0x120
el0t_64_sync+0x18c/0x190
Freed by task 357:
kasan_save_stack+0x3c/0x70
kasan_set_track+0x2c/0x40
kasan_save_free_info+0x38/0x5c
____kasan_slab_free+0x13c/0x1b0
__kasan_slab_free+0x18/0x24
__kmem_cache_free+0x130/0x2e0
kfree+0x5c/0xac
mbox_test_message_write+0x208/0x29c
full_proxy_write+0x90/0xf0
vfs_write+0x154/0x440
ksys_write+0xcc/0x180
__arm64_sys_write+0x44/0x60
invoke_syscall+0x60/0x190
el0_svc_common.constprop.0+0x7c/0x160
do_el0_svc+0x40/0xf0
el0_svc+0x2c/0x6c
el0t_64_sync_handler+0xf4/0x120
el0t_64_sync+0x18c/0x190
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec6f82b4c6 ]
The Nextbook Ares 8A tablet which has Android as factory OS, has a buggy
DSDT with both ESSX8316 and 10EC5651 ACPI devices.
This tablet actually uses an rt5651 codec, but the matching code ends up
picking the ESSX8316 device, add a quirk to ignote the ESSX8316 device
on this tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Message-Id: <20230429104721.7176-1-hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d4c937c2a5 ]
FORTIFY_SOURCE could detect various overflows at compile and run time.
ARCH_HAS_FORTIFY_SOURCE means that the architecture can be built and run
with CONFIG_FORTIFY_SOURCE. So select it in LoongArch.
See more about this feature from commit 6974f0c455 ("include/linux/
string.h: add the option of fortified string.h functions").
Signed-off-by: Qing Zhang <zhangqing@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 025ce392b5 ]
[Why]
when amdgpu_dm_update_connector_after_detect is called
two times successively with valid sink, memory allocated of
aconnector->timing_requested for the first call is not free.
this causes memeleak.
[How]
allocate memory only when aconnector->timing_requested
is null.
Reviewed-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c51e431052 ]
Add a set of HD Audio PCI IDS, and the HDMI codec vendor IDs for
Glenfly Gpus.
- In default_bdl_pos_adj, set bdl to 128 as Glenfly Gpus have hardware
limitation, need to increase hdac interrupt interval.
- In azx_first_init, enable polling mode for Glenfly Gpu. When the codec
complete the command, it sends interrupt and writes response entries to
memory, howerver, the write requests sometimes are not actually
synchronized to memory when driver handle hdac interrupt on Glenfly Gpus.
If the RIRB status is not updated in the interrupt handler,
azx_rirb_get_response keeps trying to recevie a response from rirb until
1s timeout. Enabling polling mode for Glenfly Gpu can fix the issue.
- In patch_gf_hdmi, set Glenlfy Gpu Codec's no_sticky_stream as it need
driver to do actual clean-ups for the linked codec when switch from one
codec to another.
Signed-off-by: jasontao <jasontao@glenfly.com>
Signed-off-by: Reaper Li <reaperlioc@glenfly.com>
Link: https://lore.kernel.org/r/20230426013059.4329-1-reaperlioc@glenfly.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87b22656ca ]
Doing a 'cat /dev/watchdog0' with menz069_wdt as watchdog0 will result in
a NULL pointer dereference.
This happens because we're passing the wrong pointer to
watchdog_register_device(). Fix this by getting rid of the static
watchdog_device structure and use the one embedded into the driver's
per-instance private data.
Signed-off-by: Johannes Thumshirn <jth@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230418172531.177349-2-jth@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 38eecbe086 ]
[WHY]
Function "amdgpu_irq_update()" called by "amdgpu_device_ip_late_init()" is an atomic context.
We shouldn't access registers through KIQ since "msleep()" may be called in "amdgpu_kiq_rreg()".
[HOW]
Move function "amdgpu_virt_release_full_gpu()" after function "amdgpu_device_ip_late_init()",
to ensure that registers be accessed through RLCG instead of KIQ.
Call Trace:
<TASK>
show_stack+0x52/0x69
dump_stack_lvl+0x49/0x6d
dump_stack+0x10/0x18
__schedule_bug.cold+0x4f/0x6b
__schedule+0x473/0x5d0
? __wake_up_klogd.part.0+0x40/0x70
? vprintk_emit+0xbe/0x1f0
schedule+0x68/0x110
schedule_timeout+0x87/0x160
? timer_migration_handler+0xa0/0xa0
msleep+0x2d/0x50
amdgpu_kiq_rreg+0x18d/0x1f0 [amdgpu]
amdgpu_device_rreg.part.0+0x59/0xd0 [amdgpu]
amdgpu_device_rreg+0x3a/0x50 [amdgpu]
amdgpu_sriov_rreg+0x3c/0xb0 [amdgpu]
gfx_v10_0_set_gfx_eop_interrupt_state.constprop.0+0x16c/0x190 [amdgpu]
gfx_v10_0_set_eop_interrupt_state+0xa5/0xb0 [amdgpu]
amdgpu_irq_update+0x53/0x80 [amdgpu]
amdgpu_irq_get+0x7c/0xb0 [amdgpu]
amdgpu_fence_driver_hw_init+0x58/0x90 [amdgpu]
amdgpu_device_init.cold+0x16b7/0x2022 [amdgpu]
Signed-off-by: Chong Li <chongli2@amd.com>
Reviewed-by: JingWen.Chen2@amd.com
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b1b43ee7a ]
The first subflow socket is accessed outside the msk socket lock
by mptcp_subflow_fail(), we need to annotate each write access
with WRITE_ONCE, but a few spots still lacks it.
Fixes: 76a13b3157 ("mptcp: invoke MP_FAIL response when needed")
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e8b88ec35 ]
When the msk socket is cloned at MPC handshake time, a few
fields are initialized in a racy way outside mptcp_sk_clone()
and the msk socket lock.
The above is due historical reasons: before commit a88d0092b2
("mptcp: simplify subflow_syn_recv_sock()") as the first subflow socket
carrying all the needed date was not available yet at msk creation
time
We can now refactor the code moving the missing initialization bit
under the socket lock, removing the init race and avoiding some
code duplication.
This will also simplify the next patch, as all msk->first write
access are now under the msk socket lock.
Fixes: 0397c6d85f ("mptcp: keep unaccepted MPC subflow into join list")
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5b825727d0 ]
The MPTCP can access the first subflow socket in a few spots
outside the socket lock scope. That is actually safe, as MPTCP
will delete the socket itself only after the msk sock close().
Still the such accesses causes a few KCSAN splats, as reported
by Christoph. Silence the harmless warning adding a few annotation
around the relevant accesses.
Fixes: 71ba088ce0 ("mptcp: cleanup accept and poll")
Reported-by: Christoph Paasch <cpaasch@apple.com>
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/402
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6176123169 ]
In a few spots, the mptcp code invokes the __mptcp_nmpc_socket() helper
multiple times under the same socket lock scope. Additionally, in such
places, the socket status ensures that there is no MP capable handshake
running.
Under the above condition we can replace the later __mptcp_nmpc_socket()
helper invocation with direct access to the msk->subflow pointer and
better document such access is not supposed to fail with WARN().
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 5b825727d0 ("mptcp: add annotations around msk->subflow accesses")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65d6914e25 ]
This fixes the issue that dev gro_max_size and gso_ipv4_max_size
can be set to a huge value:
# ip link add dummy1 type dummy
# ip link set dummy1 gro_max_size 4294967295
# ip -d link show dummy1
dummy addrgenmode eui64 ... gro_max_size 4294967295
Fixes: 0fe79f28bf ("net: allow gro_max_size to exceed 65536")
Fixes: 9eefedd58a ("net: add gso_ipv4_max_size and gro_ipv4_max_size per device")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fef5b228dd ]
These IFLA_GSO_* tb check should also be done for the new created link,
otherwise, they can be set to a huge value when creating links:
# ip link add dummy1 gso_max_size 4294967295 type dummy
# ip -d link show dummy1
dummy addrgenmode eui64 ... gso_max_size 4294967295
Fixes: 46e6b992c2 ("rtnetlink: allow GSO maximums to be set on device creation")
Fixes: 9eefedd58a ("net: add gso_ipv4_max_size and gro_ipv4_max_size per device")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0ad3c1790 ]
validate_linkmsg() was introduced by commit 1840bb13c2 ("[RTNL]:
Validate hardware and broadcast address attribute for RTM_NEWLINK")
to validate tb[IFLA_ADDRESS/BROADCAST] for existing links. The same
check should also be done for newly created links.
This patch adds validate_linkmsg() call in rtnl_create_link(), to
avoid the invalid address set when creating some devices like:
# ip link add dummy0 type dummy
# ip link add link dummy0 name mac0 address 01:02 type macsec
Fixes: 0e06877c6f ("[RTNETLINK]: rtnl_link: allow specifying initial device address")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4d28e30a8 ]
marvell_nfc_setup_interface() uses the frequency retrieved from the
clock associated with the nand interface to determine the timings that
will be used. By changing the NAND frequency select without reflecting
this in the clock configuration this means that the timings calculated
don't correctly meet the requirements of the NAND chip. This hasn't been
an issue up to now because of a different bug that was stopping the
timings being updated after they were initially set.
Fixes: b25251414f ("mtd: rawnand: marvell: Stop implementing ->select_chip()")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230525003154.2303012-2-chris.packham@alliedtelesis.co.nz
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c27f3d53d ]
A switch held in reset by default needs to wait longer until we can
reliably detect it.
An issue was observed when testing on the Marvell 88E6393X (Link Street).
The driver failed to detect the switch on some upstarts. Increasing the
wait time after reset deactivation solves this issue.
The updated wait time is now also the same as the wait time in the
mv88e6xxx_hardware_reset function.
Fixes: 7b75e49de4 ("net: dsa: mv88e6xxx: wait after reset deactivation")
Signed-off-by: Andreas Svensson <andreas.svensson@axis.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230530145223.1223993-1-andreas.svensson@axis.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3fc95709c ]
If an IOMMU domain was never attached, it lacks any linkage to the
actual IOMMU hardware. Attempting to do flush_iotlb_all() on it will
result in a NULL pointer dereference. This seems to happen after the
recent IOMMU core rework in v6.4-rc1.
Unable to handle kernel read from unreadable memory at virtual address 0000000000000018
Call trace:
mtk_iommu_flush_iotlb_all+0x20/0x80
iommu_create_device_direct_mappings.part.0+0x13c/0x230
iommu_setup_default_domain+0x29c/0x4d0
iommu_probe_device+0x12c/0x190
of_iommu_configure+0x140/0x208
of_dma_configure_id+0x19c/0x3c0
platform_dma_configure+0x38/0x88
really_probe+0x78/0x2c0
Check if the "bank" field has been filled in before actually attempting
the IOTLB flush to avoid it. The IOTLB is also flushed when the device
comes out of runtime suspend, so it should have a clean initial state.
Fixes: 08500c43d4 ("iommu/mediatek: Adjust the structure")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230526085402.394239-1-wenst@chromium.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bbfa4b5899 ]
During driver load it reads embedded_cpu bit from initialization
segment, but the initialization segment is readable only after
initialization bit is cleared.
Move the call to mlx5_read_embedded_cpu() right after initialization bit
cleared.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Fixes: 591905ba96 ("net/mlx5: Introduce Mellanox SmartNIC and modify page management logic")
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6193d7030 ]
Allocation failure is outside the critical lock section and should
return immediately rather than jumping to the unlock section.
Also unlock as soon as required and remove the now redundant jump label.
Fixes: 80a2a9026b ("net/mlx5e: Add a lock on tir list")
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6199d23c91 ]
If an attempt at contacting a receiver or a device fails because the
receiver or device never responds, don't restart the communication, only
restart it if the receiver or device answers that it's busy, as originally
intended.
This was the behaviour on communication timeout before commit 586e8fede7
("HID: logitech-hidpp: Retry commands when device is busy").
This fixes some overly long waits in a critical path on boot, when
checking whether the device is connected by getting its HID++ version.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Suggested-by: Mark Lord <mlord@pobox.com>
Fixes: 586e8fede7 ("HID: logitech-hidpp: Retry commands when device is busy")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217412
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c034203b6a ]
The bug here is that you cannot rely on getting the same socket
from multiple calls to fget() because userspace can influence
that. This is a kind of double fetch bug.
The fix is to delete the svc_alien_sock() function and instead do
the checking inside the svc_addsock() function.
Fixes: 3064639423 ("nfsd: check passed socket's net matches NFSd superblock's one")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: NeilBrown <neilb@suse.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 448a5ce112 ]
Syzkaller got the following report:
BUG: KASAN: use-after-free in sk_setup_caps+0x621/0x690 net/core/sock.c:2018
Read of size 8 at addr ffff888027f82780 by task syz-executor276/3255
The function sk_setup_caps (called by ip6_sk_dst_store_flow->
ip6_dst_store) referenced already freed memory as this memory was
freed by parallel task in udpv6_sendmsg->ip6_sk_dst_lookup_flow->
sk_dst_check.
task1 (connect) task2 (udp6_sendmsg)
sk_setup_caps->sk_dst_set |
| sk_dst_check->
| sk_dst_set
| dst_release
sk_setup_caps references |
to already freed dst_entry|
The reason for this race condition is: sk_setup_caps() keeps using
the dst after transferring the ownership to the dst cache.
Found by Linux Verification Center (linuxtesting.org) with syzkaller.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Vladislav Efanov <VEfanov@ispras.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36eec020fa ]
When use the following command to test:
1)ip link add bond0 type bond
2)ip link set bond0 up
3)tc qdisc add dev bond0 root handle ffff: mq
4)tc qdisc replace dev bond0 parent ffff:fff1 handle ffff: mq
The kernel reports NULL pointer dereference issue. The stack information
is as follows:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
Internal error: Oops: 0000000096000006 [#1] SMP
Modules linked in:
pstate: 20000005 (nzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : mq_attach+0x44/0xa0
lr : qdisc_graft+0x20c/0x5cc
sp : ffff80000e2236a0
x29: ffff80000e2236a0 x28: ffff0000c0e59d80 x27: ffff0000c0be19c0
x26: ffff0000cae3e800 x25: 0000000000000010 x24: 00000000fffffff1
x23: 0000000000000000 x22: ffff0000cae3e800 x21: ffff0000c9df4000
x20: ffff0000c9df4000 x19: 0000000000000000 x18: ffff80000a934000
x17: ffff8000f5b56000 x16: ffff80000bb08000 x15: 0000000000000000
x14: 0000000000000000 x13: 6b6b6b6b6b6b6b6b x12: 6b6b6b6b00000001
x11: 0000000000000000 x10: 0000000000000000 x9 : 0000000000000000
x8 : ffff0000c0be0730 x7 : bbbbbbbbbbbbbbbb x6 : 0000000000000008
x5 : ffff0000cae3e864 x4 : 0000000000000000 x3 : 0000000000000001
x2 : 0000000000000001 x1 : ffff8000090bc23c x0 : 0000000000000000
Call trace:
mq_attach+0x44/0xa0
qdisc_graft+0x20c/0x5cc
tc_modify_qdisc+0x1c4/0x664
rtnetlink_rcv_msg+0x354/0x440
netlink_rcv_skb+0x64/0x144
rtnetlink_rcv+0x28/0x34
netlink_unicast+0x1e8/0x2a4
netlink_sendmsg+0x308/0x4a0
sock_sendmsg+0x64/0xac
____sys_sendmsg+0x29c/0x358
___sys_sendmsg+0x90/0xd0
__sys_sendmsg+0x7c/0xd0
__arm64_sys_sendmsg+0x2c/0x38
invoke_syscall+0x54/0x114
el0_svc_common.constprop.1+0x90/0x174
do_el0_svc+0x3c/0xb0
el0_svc+0x24/0xec
el0t_64_sync_handler+0x90/0xb4
el0t_64_sync+0x174/0x178
This is because when mq is added for the first time, qdiscs in mq is set
to NULL in mq_attach(). Therefore, when replacing mq after adding mq, we
need to initialize qdiscs in the mq before continuing to graft. Otherwise,
it will couse NULL pointer dereference issue in mq_attach(). And the same
issue will occur in the attach functions of mqprio, taprio and htb.
ffff:fff1 means that the repalce qdisc is ingress. Ingress does not allow
any qdisc to be attached. Therefore, ffff:fff1 is incorrectly used, and
the command should be dropped.
Fixes: 6ec1c69a8f ("net_sched: add classful multiqueue dummy scheduler")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Tested-by: Peilin Ye <peilin.ye@bytedance.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://lore.kernel.org/r/20230527093747.3583502-1-shaozhengchao@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9de95df5d1 ]
Currently, after creating an ingress (or clsact) Qdisc and grafting it
under TC_H_INGRESS (TC_H_CLSACT), it is possible to graft it again under
e.g. a TBF Qdisc:
$ ip link add ifb0 type ifb
$ tc qdisc add dev ifb0 handle 1: root tbf rate 20kbit buffer 1600 limit 3000
$ tc qdisc add dev ifb0 clsact
$ tc qdisc link dev ifb0 handle ffff: parent 1:1
$ tc qdisc show dev ifb0
qdisc tbf 1: root refcnt 2 rate 20Kbit burst 1600b lat 560.0ms
qdisc clsact ffff: parent ffff:fff1 refcnt 2
^^^^^^^^
clsact's refcount has increased: it is now grafted under both
TC_H_CLSACT and 1:1.
ingress and clsact Qdiscs should only be used under TC_H_INGRESS
(TC_H_CLSACT). Prohibit regrafting them.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Fixes: 1f211a1b92 ("net, sched: add clsact qdisc")
Tested-by: Pedro Tammela <pctammela@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Peilin Ye <peilin.ye@bytedance.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f85fa45d4a ]
Currently it is possible to add e.g. an HTB Qdisc under ffff:fff1
(TC_H_INGRESS, TC_H_CLSACT):
$ ip link add name ifb0 type ifb
$ tc qdisc add dev ifb0 parent ffff:fff1 htb
$ tc qdisc add dev ifb0 clsact
Error: Exclusivity flag on, cannot modify.
$ drgn
...
>>> ifb0 = netdev_get_by_name(prog, "ifb0")
>>> qdisc = ifb0.ingress_queue.qdisc_sleeping
>>> print(qdisc.ops.id.string_().decode())
htb
>>> qdisc.flags.value_() # TCQ_F_INGRESS
2
Only allow ingress and clsact Qdiscs under ffff:fff1. Return -EINVAL
for everything else. Make TCQ_F_INGRESS a static flag of ingress and
clsact Qdiscs.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Fixes: 1f211a1b92 ("net, sched: add clsact qdisc")
Tested-by: Pedro Tammela <pctammela@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Peilin Ye <peilin.ye@bytedance.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71c6aa0305 ]
We encountered a crash when using SMCRv2. It is caused by a logical
error in smc_llc_fill_ext_v2().
BUG: kernel NULL pointer dereference, address: 0000000000000014
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 7 PID: 453 Comm: kworker/7:4 Kdump: loaded Tainted: G W E 6.4.0-rc3+ #44
Workqueue: events smc_llc_add_link_work [smc]
RIP: 0010:smc_llc_fill_ext_v2+0x117/0x280 [smc]
RSP: 0018:ffffacb5c064bd88 EFLAGS: 00010282
RAX: ffff9a6bc1c3c02c RBX: ffff9a6be3558000 RCX: 0000000000000000
RDX: 0000000000000002 RSI: 0000000000000002 RDI: 000000000000000a
RBP: ffffacb5c064bdb8 R08: 0000000000000040 R09: 000000000000000c
R10: ffff9a6bc0910300 R11: 0000000000000002 R12: 0000000000000000
R13: 0000000000000002 R14: ffff9a6bc1c3c02c R15: ffff9a6be3558250
FS: 0000000000000000(0000) GS:ffff9a6eefdc0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000014 CR3: 000000010b078003 CR4: 00000000003706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
smc_llc_send_add_link+0x1ae/0x2f0 [smc]
smc_llc_srv_add_link+0x2c9/0x5a0 [smc]
? cc_mkenc+0x40/0x60
smc_llc_add_link_work+0xb8/0x140 [smc]
process_one_work+0x1e5/0x3f0
worker_thread+0x4d/0x2f0
? __pfx_worker_thread+0x10/0x10
kthread+0xe5/0x120
? __pfx_kthread+0x10/0x10
ret_from_fork+0x2c/0x50
</TASK>
When an alernate RNIC is available in system, SMC will try to add a new
link based on the RNIC for resilience. All the RMBs in use will be mapped
to the new link. Then the RMBs' MRs corresponding to the new link will be
filled into SMCRv2 LLC ADD LINK messages.
However, smc_llc_fill_ext_v2() mistakenly accesses to unused RMBs which
haven't been mapped to the new link and have no valid MRs, thus causing
a crash. So this patch fixes the logic.
Fixes: b4ba4652b3 ("net/smc: extend LLC layer for SMC-Rv2")
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b24aa141c2 ]
When finding the first RMB of link group, it should start from the
current RMB list whose index is 0. So fix it.
Fixes: b4ba4652b3 ("net/smc: extend LLC layer for SMC-Rv2")
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8f304d75f ]
There is a window where the poll cq may use a QP that has been freed.
This can happen if a CQE is polled before irdma_clean_cqes() can clear the
CQE's related to the QP and the destroy QP races to free the QP memory.
then the QP structures are used in irdma_poll_cq. Fix this by moving the
clearing of CQE's before the reference is removed and the QP is destroyed.
Fixes: b48c24c2d7 ("RDMA/irdma: Implement device supported verb APIs")
Link: https://lore.kernel.org/r/20230522155654.1309-3-shiraz.saleem@intel.com
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36e4fc57fc ]
The macOS hypervisor framework includes a host-side VMM called
VZLinuxBootLoader [1] which implements native support for booting the
Linux kernel inside a guest directly (instead of, e.g., via GRUB
installed inside the guest). On x86, it incorporates a BIOS style loader
that does not implement or expose EFI to the loaded kernel. However,
this loader appears to fail when the 'image minor version' field in the
kernel image's PE/COFF header (which is generally only used by EFI based
bootloaders) is set to any value other than 0x0. [2]
Commit e346bebbd3 ("efi: libstub: Always enable initrd command
line loader and bump version") incremented the EFI stub image minor
version to convey that all EFI stub kernels now implement support for
the initrd= command line option, and do so in a way where it can load
initrd images from any filesystem known to the EFI firmware (as opposed
to prior implementations that could only load initrds from the same
volume that the kernel image was loaded from).
Unfortunately, bumping the version to v1.1 triggers this issue in
VZLinuxBootLoader, breaking the boot on x86. So let's keep the image
minor version at 0x0, and bump the image major version instead.
While at it, convert this field to a bit field, so that individual
features are discoverable from it, as suggested by Linus. So let's bump
the major version to v3, and document the initrd= command line loading
feature as being represented by bit 1 in the mask.
Note that, due to the prior interpretation as a monotonically increasing
version field, loaders are still permitted to assume that the LoadFile2
initrd loading feature is supported for any major version value >= 1,
even if bit 0 is not set.
[1] https://developer.apple.com/documentation/virtualization/vzlinuxbootloader
[2] https://lore.kernel.org/linux-efi/CAG8fp8Teu4G9JuenQrqGndFt2Gy+V4YgJ=hN1xX7AD940YKf3A@mail.gmail.com/
Fixes: e346bebbd3 ("efi: libstub: Always enable initrd command ...")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217485
Signed-off-by: Akihiro Suda <suda.kyoto@gmail.com>
[ardb: rewrite comment and commit log]
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 650a8884a3 ]
A few functions provide an empty interface definition when
CONFIG_MTD_NAND_INGENIC_ECC is disabled, but they are accidentally
defined as global functions in the header:
drivers/mtd/nand/raw/ingenic/ingenic_ecc.h:39:5: error: no previous prototype for 'ingenic_ecc_calculate'
drivers/mtd/nand/raw/ingenic/ingenic_ecc.h:46:5: error: no previous prototype for 'ingenic_ecc_correct'
drivers/mtd/nand/raw/ingenic/ingenic_ecc.h:53:6: error: no previous prototype for 'ingenic_ecc_release'
drivers/mtd/nand/raw/ingenic/ingenic_ecc.h:57:21: error: no previous prototype for 'of_ingenic_ecc_get'
Turn them into 'static inline' definitions instead.
Fixes: 15de8c6efd ("mtd: rawnand: ingenic: Separate top-level and SoC specific code")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230516202133.559488-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d73259ef2 ]
The option name should not have the dashes. Current version shows four
dashes for the option.
$ perf ftrace latency -h
Usage: perf ftrace [<options>] [<command>]
or: perf ftrace [<options>] -- [<command>] [<options>]
or: perf ftrace {trace|latency} [<options>] [<command>]
or: perf ftrace {trace|latency} [<options>] -- [<command>] [<options>]
-b, --use-bpf Use BPF to measure function latency
-n, ----use-nsec Use nano-second histogram
-T, --trace-funcs <func>
Show latency of given function
Fixes: 84005bb614 ("perf ftrace latency: Add -n/--use-nsec option")
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Changbin Du <changbin.du@huawei.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20230525212038.3535851-1-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc362e20cd ]
In the event of a change in XGBE mode, the current auto-negotiation
needs to be reset and the AN cycle needs to be re-triggerred. However,
the current code ignores the return value of xgbe_set_mode(), leading to
false information as the link is declared without checking the status
register.
Fix this by propagating the mode switch status information to
xgbe_phy_status().
Fixes: e57f7a3fea ("amd-xgbe: Prepare for working with more than one type of phy")
Co-developed-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Signed-off-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a0d57df89 ]
Most protos' poll() methods insert a memory barrier between
writes to sk_err and sk_error_report(). This dates back to
commit a4d258036e ("tcp: Fix race in tcp_poll").
I guess we should do the same thing in TLS, tcp_poll() does
not hold the socket lock.
Fixes: 3c4d755915 ("tls: kernel TLS support")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 822b5a1c17 ]
syzkaller found a data race of pkt_sk(sk)->num.
The value is changed under lock_sock() and po->bind_lock, so we
need READ_ONCE() to access pkt_sk(sk)->num without these locks in
packet_bind_spkt(), packet_bind(), and sk_diag_fill().
Note that WRITE_ONCE() is already added by commit c7d2ef5dd4
("net/packet: annotate accesses to po->bind").
BUG: KCSAN: data-race in packet_bind / packet_do_bind
write (marked) to 0xffff88802ffd1cee of 2 bytes by task 7322 on cpu 0:
packet_do_bind+0x446/0x640 net/packet/af_packet.c:3236
packet_bind+0x99/0xe0 net/packet/af_packet.c:3321
__sys_bind+0x19b/0x1e0 net/socket.c:1803
__do_sys_bind net/socket.c:1814 [inline]
__se_sys_bind net/socket.c:1812 [inline]
__x64_sys_bind+0x40/0x50 net/socket.c:1812
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3b/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x72/0xdc
read to 0xffff88802ffd1cee of 2 bytes by task 7318 on cpu 1:
packet_bind+0xbf/0xe0 net/packet/af_packet.c:3322
__sys_bind+0x19b/0x1e0 net/socket.c:1803
__do_sys_bind net/socket.c:1814 [inline]
__se_sys_bind net/socket.c:1812 [inline]
__x64_sys_bind+0x40/0x50 net/socket.c:1812
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3b/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x72/0xdc
value changed: 0x0300 -> 0x0000
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 7318 Comm: syz-executor.4 Not tainted 6.3.0-13380-g7fddb5b5300c #4
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
Fixes: 96ec632714 ("packet: Diag core and basic socket info dumping")
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: syzkaller <syzkaller@googlegroups.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20230524232934.50950-1-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31642e7089 ]
Simon Kapadia reported the following issue:
<quote>
The Online Amateur Radio Community (OARC) has recently been experimenting
with building a nationwide packet network in the UK.
As part of our experimentation, we have been testing out packet on 300bps HF,
and playing with net/rom. For HF packet at this baud rate you really need
to make sure that your MTU is relatively low; AX.25 suggests a PACLEN of 60,
and a net/rom PACLEN of 40 to go with that.
However the Linux net/rom support didn't work with a low PACLEN;
the mkiss module would truncate packets if you set the PACLEN below about 200 or so, e.g.:
Apr 19 14:00:51 radio kernel: [12985.747310] mkiss: ax1: truncating oversized transmit packet!
This didn't make any sense to me (if the packets are smaller why would they
be truncated?) so I started investigating.
I looked at the packets using ethereal, and found that many were just huge
compared to what I would expect.
A simple net/rom connection request packet had the request and then a bunch
of what appeared to be random data following it:
</quote>
Simon provided a patch that I slightly revised:
Not only we must not use skb_tailroom(), we also do
not want to count NR_NETWORK_LEN twice.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Co-Developed-by: Simon Kapadia <szymon@kapadia.pl>
Signed-off-by: Simon Kapadia <szymon@kapadia.pl>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Simon Kapadia <szymon@kapadia.pl>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230524141456.1045467-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ffb3322181 ]
We encountered a kernel call trace issue which was related to
ndo_xdp_xmit callback on our i.MX8MP platform. The reproduce
steps show as follows.
1. The FEC port (eth0) connects to a PC port, and the PC uses
pktgen_sample03_burst_single_flow.sh to generate packets and
send these packets to the FEC port. Notice that the script must
be executed before step 2.
2. Run the "./xdp_redirect eth0 eth1" command on i.MX8MP, the
eth1 interface is the dwmac. Then there will be a call trace
issue soon. Please see the log for more details.
The root cause is that the NETDEV_XDP_ACT_NDO_XMIT feature is
enabled by default, so when the step 2 command is exexcuted
and packets have already been sent to eth0, the stmmac_xdp_xmit()
starts running before the stmmac_xdp_set_prog() finishes. To
resolve this issue, we disable the NETDEV_XDP_ACT_NDO_XMIT
feature by default and turn on/off this feature when the bpf
program is installed/uninstalled which just like the other
ethernet drivers.
Call Trace log:
[ 306.311271] ------------[ cut here ]------------
[ 306.315910] WARNING: CPU: 0 PID: 15 at lib/timerqueue.c:55 timerqueue_del+0x68/0x70
[ 306.323590] Modules linked in:
[ 306.326654] CPU: 0 PID: 15 Comm: ksoftirqd/0 Not tainted 6.4.0-rc1+ #37
[ 306.333277] Hardware name: NXP i.MX8MPlus EVK board (DT)
[ 306.338591] pstate: 600000c5 (nZCv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 306.345561] pc : timerqueue_del+0x68/0x70
[ 306.349577] lr : __remove_hrtimer+0x5c/0xa0
[ 306.353777] sp : ffff80000b7c3920
[ 306.357094] x29: ffff80000b7c3920 x28: 0000000000000000 x27: 0000000000000001
[ 306.364244] x26: ffff80000a763a40 x25: ffff0000d0285a00 x24: 0000000000000001
[ 306.371390] x23: 0000000000000001 x22: ffff000179389a40 x21: 0000000000000000
[ 306.378537] x20: ffff000179389aa0 x19: ffff0000d2951308 x18: 0000000000001000
[ 306.385686] x17: f1d3000000000000 x16: 00000000c39c1000 x15: 55e99bbe00001a00
[ 306.392835] x14: 09000900120aa8c0 x13: e49af1d300000000 x12: 000000000000c39c
[ 306.399987] x11: 100055e99bbe0000 x10: ffff8000090b1048 x9 : ffff8000081603fc
[ 306.407133] x8 : 000000000000003c x7 : 000000000000003c x6 : 0000000000000001
[ 306.414284] x5 : ffff0000d2950980 x4 : 0000000000000000 x3 : 0000000000000000
[ 306.421432] x2 : 0000000000000001 x1 : ffff0000d2951308 x0 : ffff0000d2951308
[ 306.428585] Call trace:
[ 306.431035] timerqueue_del+0x68/0x70
[ 306.434706] __remove_hrtimer+0x5c/0xa0
[ 306.438549] hrtimer_start_range_ns+0x2bc/0x370
[ 306.443089] stmmac_xdp_xmit+0x174/0x1b0
[ 306.447021] bq_xmit_all+0x194/0x4b0
[ 306.450612] __dev_flush+0x4c/0x98
[ 306.454024] xdp_do_flush+0x18/0x38
[ 306.457522] fec_enet_rx_napi+0x6c8/0xc68
[ 306.461539] __napi_poll+0x40/0x220
[ 306.465038] net_rx_action+0xf8/0x240
[ 306.468707] __do_softirq+0x128/0x3a8
[ 306.472378] run_ksoftirqd+0x40/0x58
[ 306.475961] smpboot_thread_fn+0x1c4/0x288
[ 306.480068] kthread+0x124/0x138
[ 306.483305] ret_from_fork+0x10/0x20
[ 306.486889] ---[ end trace 0000000000000000 ]---
Fixes: 66c0e13ad2 ("drivers: net: turn on XDP features")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230524125714.357337-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4c24fc30c ]
As priv->dfs_root is cleared, and therefore missed, when change
eswitch mode, move the creation of the root debugfs to the init
callback of mlx5e_nic_profile and mlx5e_uplink_rep_profile, and
the destruction to the cleanup callback for symmeter.
Fixes: 288eca60cc ("net/mlx5e: Add Ethernet driver debugfs")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bdf274750f ]
As part of switchdev mode disablement, driver changes port netdevice
profile from uplink to nic. If this process is triggered by health
recovery flow (PCI reset, for ex.) profile attach would fail because all
fw commands aborted when internal error flag is set. As a result, nic
netdevice profile is not attached and driver fails to rollback to uplink
profile, which leave driver in broken state and cause crash later.
To handle broken state do netdevice profile initialization only instead
of full attachment and release mdev resources on driver suspend as
expected. Actual netdevice attachment is done during driver load.
Fixes: c4d7eb5768 ("net/mxl5e: Add change profile method")
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d862ec631 ]
Caller of mlx5e_tc_act_post_parse() needs it to parse only the subset of
actions starting after previous split and ending at the current action.
However, that range is not provided as arguments and
mlx5e_tc_act_post_parse() uses generic flow_action_for_each() that iterates
over all flow actions. Not only this is redundant, it also causes a bug
when mlx5e_tc_act->post_parse() callback is not idempotent since it will be
called for every split. For example, ct action tc_act_post_parse_ct()
callback obtains a reference to mlx5_ct_ft instance and calling it several
times during parsing stage will cause reference counter imbalance.
Fix the issue by providing a proper action range of the current split
subset to mlx5e_tc_act_post_parse() and only calling
mlx5e_tc_act->post_parse() for actions inside the subset range.
Fixes: 8300f22526 ("net/mlx5e: Create new flow attr for multi table actions")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 67efaf4593 ]
CT action reordering was done as a workaround when CT misses
used to restore the relevant filter's tc chain and continuing sw processing
from that chain. As such, there was a need to reorder CT action to be before
any packet modifying actions (e.g mac rewrite).
Currently (after patch "net/mlx5e: TC, Set CT miss to the specific ct
action instance"), CT misses continues from the relevant ct action in
software, and so reordering isn't needed anymore.
Remove the reordering.
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Stable-dep-of: 5d862ec631 ("net/mlx5: Fix post parse infra to only parse every action once")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 13aca17b45 ]
CT action can miss in a middle of an action list, use
per action stats to correctly report stats for missed
packets.
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Stable-dep-of: 5d862ec631 ("net/mlx5: Fix post parse infra to only parse every action once")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1db1f21cae ]
Don't query the firmware so many times (num rqs * num wqes * wqe frags)
because it slows down linearly the interface creation time when the
product is larger. Do it only once per mdev and store the result in
mlx5e_param.
Due to helper function being called from different files, move it to
an appropriate location. Rename the function with a proper prefix and
add a small cleanup.
This fix applies only for legacy rq.
Fixes: 1b1e486883 ("net/mlx5e: Use query_special_contexts for mkeys")
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Or Har-Toov <ohartoov@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 341a80de24 ]
mlx5 driver needs to parse traces with event_id inside the range of
first_string_trace and num_string_trace. However, mlx5 is parsing all
events with event_id >= first_string_trace.
Fix it by checking for the correct range.
Fixes: c71ad41ccb ("net/mlx5: FW tracer, events handling")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4646da057 ]
There is no point in recovery during device removal. Also, if health
work started need to wait for it to avoid races and NULL pointer
access.
Hence, drain health WQ before removing device.
Fixes: 1958fc2f07 ("net/mlx5: SF, Add auxiliary device driver")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 824c8dc4a4 ]
mlx5 health mechanism is using devlink APIs, which are using devlink
notify APIs. After the cited patch, using devlink notify APIs after
devlink is unregistered triggers a WARN_ON().
Hence, drain health WQ before devlink is unregistered.
Fixes: cf53021740 ("devlink: Notify users when objects are accessible")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 623efc4cbd ]
The shared buffer pools configuration which are stored in the SBCM
register are updated when the user changes the prio2buffer mapping.
However, in case the user desired prio2buffer change is invalid,
which can occur due to mapping a lossless priority to a not large enough
buffer, the SBCM update should not be performed, as the user command is
failed.
Thus, Perform the SBCM update only after xoff threshold calculation is
performed and the user prio2buffer mapping is validated.
Fixes: a440030d89 ("net/mlx5e: Update shared buffer along with device buffer changes")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 81fe2be062 ]
Currently, when a user triggers a change in port buffer headroom
(buffers 0-7), the driver checks that the requested headroom does
not exceed the total port buffer size. However, this check does not
take into account the internal buffers (buffers 8-9), which are also
part of the total port buffer. This can result in treating invalid port
buffer change requests as valid, causing unintended changes to the shared
buffer.
To address this, include the internal buffers size in the calculation of
available port buffer space which ensures that port buffer requests do not
exceed the correct limit.
Furthermore, remove internal buffers (8-9) size from the total_size
calculation as these buffers are reserved for internal use and are not
exposed to the user.
While at it, add verbosity to the debug prints in
mlx5e_port_query_buffer() function to ease future debugging.
Fixes: ecdf2dadee ("net/mlx5e: Receive buffer support for DCBX")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37c3b9fa7c ]
The cited commit adds a compeletion to remove dependency on rtnl
lock. But it causes a deadlock for multiple encapsulations:
crash> bt ffff8aece8a64000
PID: 1514557 TASK: ffff8aece8a64000 CPU: 3 COMMAND: "tc"
#0 [ffffa6d14183f368] __schedule at ffffffffb8ba7f45
#1 [ffffa6d14183f3f8] schedule at ffffffffb8ba8418
#2 [ffffa6d14183f418] schedule_preempt_disabled at ffffffffb8ba8898
#3 [ffffa6d14183f428] __mutex_lock at ffffffffb8baa7f8
#4 [ffffa6d14183f4d0] mutex_lock_nested at ffffffffb8baabeb
#5 [ffffa6d14183f4e0] mlx5e_attach_encap at ffffffffc0f48c17 [mlx5_core]
#6 [ffffa6d14183f628] mlx5e_tc_add_fdb_flow at ffffffffc0f39680 [mlx5_core]
#7 [ffffa6d14183f688] __mlx5e_add_fdb_flow at ffffffffc0f3b636 [mlx5_core]
#8 [ffffa6d14183f6f0] mlx5e_tc_add_flow at ffffffffc0f3bcdf [mlx5_core]
#9 [ffffa6d14183f728] mlx5e_configure_flower at ffffffffc0f3c1d1 [mlx5_core]
#10 [ffffa6d14183f790] mlx5e_rep_setup_tc_cls_flower at ffffffffc0f3d529 [mlx5_core]
#11 [ffffa6d14183f7a0] mlx5e_rep_setup_tc_cb at ffffffffc0f3d714 [mlx5_core]
#12 [ffffa6d14183f7b0] tc_setup_cb_add at ffffffffb8931bb8
#13 [ffffa6d14183f810] fl_hw_replace_filter at ffffffffc0dae901 [cls_flower]
#14 [ffffa6d14183f8d8] fl_change at ffffffffc0db5c57 [cls_flower]
#15 [ffffa6d14183f970] tc_new_tfilter at ffffffffb8936047
#16 [ffffa6d14183fac8] rtnetlink_rcv_msg at ffffffffb88c7c31
#17 [ffffa6d14183fb50] netlink_rcv_skb at ffffffffb8942853
#18 [ffffa6d14183fbc0] rtnetlink_rcv at ffffffffb88c1835
#19 [ffffa6d14183fbd0] netlink_unicast at ffffffffb8941f27
#20 [ffffa6d14183fc18] netlink_sendmsg at ffffffffb8942245
#21 [ffffa6d14183fc98] sock_sendmsg at ffffffffb887d482
#22 [ffffa6d14183fcb8] ____sys_sendmsg at ffffffffb887d81a
#23 [ffffa6d14183fd38] ___sys_sendmsg at ffffffffb88806e2
#24 [ffffa6d14183fe90] __sys_sendmsg at ffffffffb88807a2
#25 [ffffa6d14183ff28] __x64_sys_sendmsg at ffffffffb888080f
#26 [ffffa6d14183ff38] do_syscall_64 at ffffffffb8b9b6a8
#27 [ffffa6d14183ff50] entry_SYSCALL_64_after_hwframe at ffffffffb8c0007c
crash> bt 0xffff8aeb07544000
PID: 1110766 TASK: ffff8aeb07544000 CPU: 0 COMMAND: "kworker/u20:9"
#0 [ffffa6d14e6b7bd8] __schedule at ffffffffb8ba7f45
#1 [ffffa6d14e6b7c68] schedule at ffffffffb8ba8418
#2 [ffffa6d14e6b7c88] schedule_timeout at ffffffffb8baef88
#3 [ffffa6d14e6b7d10] wait_for_completion at ffffffffb8ba968b
#4 [ffffa6d14e6b7d60] mlx5e_take_all_encap_flows at ffffffffc0f47ec4 [mlx5_core]
#5 [ffffa6d14e6b7da0] mlx5e_rep_update_flows at ffffffffc0f3e734 [mlx5_core]
#6 [ffffa6d14e6b7df8] mlx5e_rep_neigh_update at ffffffffc0f400bb [mlx5_core]
#7 [ffffa6d14e6b7e50] process_one_work at ffffffffb80acc9c
#8 [ffffa6d14e6b7ed0] worker_thread at ffffffffb80ad012
#9 [ffffa6d14e6b7f10] kthread at ffffffffb80b615d
#10 [ffffa6d14e6b7f50] ret_from_fork at ffffffffb8001b2f
After the first encap is attached, flow will be added to encap
entry's flows list. If neigh update is running at this time, the
following encaps of the flow can't hold the encap_tbl_lock and
sleep. If neigh update thread is waiting for that flow's init_done,
deadlock happens.
Fix it by holding lock outside of the for loop. If neigh update is
running, prevent encap flows from offloading. Since the lock is held
outside of the for loop, concurrent creation of encap entries is not
allowed. So remove unnecessary wait_for_completion call for res_ready.
Fixes: 95435ad799 ("net/mlx5e: Only access fully initialized flows in neigh update")
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e2ab5aa11f ]
Move set_encap_dests() and clean_encap_dests() to the tunnel encap
dedicated file. And rename them to mlx5e_tc_tun_encap_dests_set()
and mlx5e_tc_tun_encap_dests_unset().
No functional change in this patch. It is needed in the next patch.
Signed-off-by: Chris Mi <cmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Stable-dep-of: 37c3b9fa7c ("net/mlx5e: Prevent encap offload when neigh update is running")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a830ec485e ]
Actions that can be setup per flow attribute (so per split rule)
are cleaned up from mlx5_free_flow_attr(), mlx5e_tc_del_fdb_flow(),
and free_flow_post_acts().
Remove the duplication by re-using the helper function for
the main flow attribute and split rules attributes.
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Stable-dep-of: 37c3b9fa7c ("net/mlx5e: Prevent encap offload when neigh update is running")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7195d9a0c8 ]
vf_tun is being assigned but never being used so remove it.
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Stable-dep-of: 37c3b9fa7c ("net/mlx5e: Prevent encap offload when neigh update is running")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 33d418da6f ]
commit ef69d2559f ("riscv: Move early dtb mapping into the fixmap
region") wrongly moved the #ifndef CONFIG_BUILTIN_DTB surrounding the pa
variable definition in create_fdt_early_page_table(), so move it back to
its right place to quiet the following warning:
../arch/riscv/mm/init.c: In function ‘create_fdt_early_page_table’:
../arch/riscv/mm/init.c:925:12: warning: unused variable ‘pa’ [-Wunused-variable]
925 | uintptr_t pa = dtb_pa & ~(PMD_SIZE - 1);
Fixes: ef69d2559f ("riscv: Move early dtb mapping into the fixmap region")
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230519131311.391960-1-alexghiti@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ab39f9992 ]
The GFNI routines in the AVX version of the ARIA implementation now use
explicit VMOVDQA instructions to load the constant input vectors, which
means they must be 16 byte aligned. So ensure that this is the case, by
dropping the section split and the incorrect .align 8 directive, and
emitting the constants into the 16-byte aligned section instead.
Note that the AVX2 version of this code deviates from this pattern, and
does not require a similar fix, given that it loads these contants as
8-byte memory operands, for which AVX2 permits any alignment.
Cc: Taehee Yoo <ap420073@gmail.com>
Fixes: 8b84475318 ("crypto: x86/aria-avx - Do not use avx2 instructions")
Reported-by: syzbot+a6abcf08bad8b18fd198@syzkaller.appspotmail.com
Tested-by: syzbot+a6abcf08bad8b18fd198@syzkaller.appspotmail.com
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1a5f2c887 ]
"_start" is used in several arches and proably should be reserved
for ARCH usage. Using it in a driver for a private symbol can cause
a build error when it conflicts with ARCH usage of the same symbol.
Therefore rename pl330's "_start" to "pl330_start_thread" so that there
is no conflict and no build error.
drivers/dma/pl330.c:1053:13: error: '_start' redeclared as different kind of symbol
1053 | static bool _start(struct pl330_thread *thrd)
| ^~~~~~
In file included from ../include/linux/interrupt.h:21,
from ../drivers/dma/pl330.c:18:
arch/riscv/include/asm/sections.h:11:13: note: previous declaration of '_start' with type 'char[]'
11 | extern char _start[];
| ^~~~~~
Fixes: b7d861d939 ("DMA: PL330: Merge PL330 driver into drivers/dma/")
Fixes: ae43b32891 ("ARM: 8202/1: dmaengine: pl330: Add runtime Power Management support v12")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jaswinder Singh <jassisinghbrar@gmail.com>
Cc: Boojin Kim <boojin.kim@samsung.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: dmaengine@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
Link: https://lore.kernel.org/r/20230524045310.27923-1-rdunlap@infradead.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d53d70084d ]
notify_change can modify the iattr structure. In particular it can
end up setting ATTR_MODE when ATTR_KILL_SUID is already set, causing
a BUG() if the same iattr is passed to notify_change more than once.
Make a copy of the struct iattr before calling notify_change.
Reported-by: Zhi Li <yieli@redhat.com>
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2207969
Tested-by: Zhi Li <yieli@redhat.com>
Fixes: 34b91dda71 ("NFSD: Make nfsd4_setattr() wait before returning NFS4ERR_DELAY")
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 29f54745f2 ]
Drivers are supposed to list the domain types they support in their
domain_alloc() ops so when we add new domain types, like BLOCKING or SVA,
they don't start breaking.
This ended up providing an empty UNMANAGED domain when the core code asked
for a BLOCKING domain, which happens to be the fallback for drivers that
don't support it, but this is completely wrong for SVA.
Check for the DMA types AMD supports and reject every other kind.
Fixes: 136467962e ("iommu: Add IOMMU SVA domain support")
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/0-v1-2ac37b893728+da-amd_check_types_jgg@nvidia.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af47b0a240 ]
GALog exists to propagate interrupts into all vCPUs in the system when
interrupts are marked as non running (e.g. when vCPUs aren't running). A
GALog overflow happens when there's in no space in the log to record the
GATag of the interrupt. So when the GALOverflow condition happens, the
GALog queue is processed and the GALog is restarted, as the IOMMU
manual indicates in section "2.7.4 Guest Virtual APIC Log Restart
Procedure":
| * Wait until MMIO Offset 2020h[GALogRun]=0b so that all request
| entries are completed as circumstances allow. GALogRun must be 0b to
| modify the guest virtual APIC log registers safely.
| * Write MMIO Offset 0018h[GALogEn]=0b.
| * As necessary, change the following values (e.g., to relocate or
| resize the guest virtual APIC event log):
| - the Guest Virtual APIC Log Base Address Register
| [MMIO Offset 00E0h],
| - the Guest Virtual APIC Log Head Pointer Register
| [MMIO Offset 2040h][GALogHead], and
| - the Guest Virtual APIC Log Tail Pointer Register
| [MMIO Offset 2048h][GALogTail].
| * Write MMIO Offset 2020h[GALOverflow] = 1b to clear the bit (W1C).
| * Write MMIO Offset 0018h[GALogEn] = 1b, and either set
| MMIO Offset 0018h[GAIntEn] to enable the GA log interrupt or clear
| the bit to disable it.
Failing to handle the GALog overflow means that none of the VFs (in any
guest) will work with IOMMU AVIC forcing the user to power cycle the
host. When handling the event it resumes the GALog without resizing
much like how it is done in the event handler overflow. The
[MMIO Offset 2020h][GALOverflow] bit might be set in status register
without the [MMIO Offset 2020h][GAInt] bit, so when deciding to poll
for GA events (to clear space in the galog), also check the overflow
bit.
[suravee: Check for GAOverflow without GAInt, toggle CONTROL_GAINT_EN]
Co-developed-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Link: https://lore.kernel.org/r/20230419201154.83880-3-joao.m.martins@oracle.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Stable-dep-of: 8ec4e2befe ("iommu/amd: Fix up merge conflict resolution")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed8a2f4dde ]
On KVM GSI routing table updates, specially those where they have vIOMMUs
with interrupt remapping enabled (to boot >255vcpus setups without relying
on KVM_FEATURE_MSI_EXT_DEST_ID), a VMM may update the backing VF MSIs
with a new VCPU affinity.
On AMD with AVIC enabled, the new vcpu affinity info is updated via:
avic_pi_update_irte()
irq_set_vcpu_affinity()
amd_ir_set_vcpu_affinity()
amd_iommu_{de}activate_guest_mode()
Where the IRTE[GATag] is updated with the new vcpu affinity. The GATag
contains VM ID and VCPU ID, and is used by IOMMU hardware to signal KVM
(via GALog) when interrupt cannot be delivered due to vCPU is in
blocking state.
The issue is that amd_iommu_activate_guest_mode() will essentially
only change IRTE fields on transitions from non-guest-mode to guest-mode
and otherwise returns *with no changes to IRTE* on already configured
guest-mode interrupts. To the guest this means that the VF interrupts
remain affined to the first vCPU they were first configured, and guest
will be unable to issue VF interrupts and receive messages like this
from spurious interrupts (e.g. from waking the wrong vCPU in GALog):
[ 167.759472] __common_interrupt: 3.34 No irq handler for vector
[ 230.680927] mlx5_core 0000:00:02.0: mlx5_cmd_eq_recover:247:(pid
3122): Recovered 1 EQEs on cmd_eq
[ 230.681799] mlx5_core 0000:00:02.0:
wait_func_handle_exec_timeout:1113:(pid 3122): cmd[0]: CREATE_CQ(0x400)
recovered after timeout
[ 230.683266] __common_interrupt: 3.34 No irq handler for vector
Given the fact that amd_ir_set_vcpu_affinity() uses
amd_iommu_activate_guest_mode() underneath it essentially means that VCPU
affinity changes of IRTEs are nops. Fix it by dropping the check for
guest-mode at amd_iommu_activate_guest_mode(). Same thing is applicable to
amd_iommu_deactivate_guest_mode() although, even if the IRTE doesn't change
underlying DestID on the host, the VFIO IRQ handler will still be able to
poke at the right guest-vCPU.
Fixes: b9c6ff94e4 ("iommu/amd: Re-factor guest virtual APIC (de-)activation code")
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Reviewed-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Link: https://lore.kernel.org/r/20230419201154.83880-2-joao.m.martins@oracle.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec014683c5 ]
Smatch complains that
drivers/iommu/rockchip-iommu.c:1306 rk_iommu_probe() warn: missing unwind goto?
The rk_iommu_probe function, after obtaining the irq value through
platform_get_irq, directly returns an error if the returned value
is negative, without releasing any resources.
Fix this by adding a new error handling label "err_pm_disable" and
use a goto statement to redirect to the error handling process. In
order to preserve the original semantics, set err to the value of irq.
Fixes: 1aa55ca9b1 ("iommu/rockchip: Move irq request past pm_runtime_enable")
Signed-off-by: Chao Wang <D202280639@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20230417030421.2777-1-D202280639@hust.edu.cn
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e332003bb2 ]
On riscv64, linux-next-20233030 (and for several days earlier),
there is a kconfig warning:
WARNING: unmet direct dependencies detected for IOMMU_IO_PGTABLE_LPAE
Depends on [n]: IOMMU_SUPPORT [=y] && (ARM || ARM64 || COMPILE_TEST [=n]) && !GENERIC_ATOMIC64 [=n]
Selected by [y]:
- IPMMU_VMSA [=y] && IOMMU_SUPPORT [=y] && (ARCH_RENESAS [=y] || COMPILE_TEST [=n]) && !GENERIC_ATOMIC64 [=n]
and build errors:
riscv64-linux-ld: drivers/iommu/io-pgtable-arm.o: in function `.L140':
io-pgtable-arm.c:(.init.text+0x1e8): undefined reference to `alloc_io_pgtable_ops'
riscv64-linux-ld: drivers/iommu/io-pgtable-arm.o: in function `.L168':
io-pgtable-arm.c:(.init.text+0xab0): undefined reference to `free_io_pgtable_ops'
riscv64-linux-ld: drivers/iommu/ipmmu-vmsa.o: in function `.L140':
ipmmu-vmsa.c:(.text+0xbc4): undefined reference to `free_io_pgtable_ops'
riscv64-linux-ld: drivers/iommu/ipmmu-vmsa.o: in function `.L0 ':
ipmmu-vmsa.c:(.text+0x145e): undefined reference to `alloc_io_pgtable_ops'
Add ARM || ARM64 || COMPILE_TEST dependencies to IPMMU_VMSA to prevent
these issues, i.e., so that ARCH_RENESAS on RISC-V is not allowed.
This makes the ARCH dependencies become:
depends on (ARCH_RENESAS && (ARM || ARM64)) || COMPILE_TEST
but that can be a bit hard to read.
Fixes: 8292493c22 ("riscv: Kconfig.socs: Add ARCH_RENESAS kconfig option")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Will Deacon <will@kernel.org>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: iommu@lists.linux.dev
Cc: Conor Dooley <conor@kernel.org>
Cc: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20230330165817.21920-1-rdunlap@infradead.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d43acb145 ]
There are two place if the at_xdmac_interleaved_queue_desc() fails which
could lead to a NULL dereference where "first" is NULL and we call
list_add_tail(&first->desc_node, ...). In the first caller, the return
is not checked so add a check for that. In the next caller, the return
is checked but if it fails on the first iteration through the loop then
it will lead to a NULL pointer dereference.
Fixes: 4e5385784e ("dmaengine: at_xdmac: handle numf > 1")
Fixes: 62b5cb757f ("dmaengine: at_xdmac: fix memory leak in interleaved mode")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/21282b66-9860-410a-83df-39c17fcf2f1b@kili.mountain
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56518a603f ]
Long message loopback slice is used for achieving traffic balance between
QPs. It prevents the problem that QPs with large traffic occupying the
hardware pipeline for a long time and QPs with small traffic cannot be
scheduled.
Currently, its maximum value is set to 16K, which means only after a QP
sends 16K will the second QP be scheduled. This value is too large, which
will lead to unbalanced traffic scheduling, and thus it needs to be
modified.
The setting range of the long message loopback slice is modified to be
from 1024 (the lower limit supported by hardware) to mtu. Actual testing
shows that this value can significantly reduce error in hardware traffic
scheduling.
This solution is compatible with both HIP08 and HIP09. The modified
lp_pktn_ini has a maximum value of 2 (when mtu is 256), so the range
checking code for lp_pktn_ini is no longer necessary and needs to be
deleted.
Fixes: 0e60778efb ("RDMA/hns: Modify the value of MAX_LP_MSG_LEN to meet hardware compatibility")
Link: https://lore.kernel.org/r/20230512092245.344442-4-huangjunxian6@hisilicon.com
Signed-off-by: Yangyang Li <liyangyang20@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f3969b14f ]
For hns, the specification of an entry like resource (E.g. WQE/CQE/EQE)
depends on BT page size, buf page size and hopnum. For user mode, the buf
page size depends on UMEM. Therefore, the actual specification is
controlled by BT page size and hopnum.
The current BT page size and hopnum are obtained from firmware. This makes
the driver inflexible and introduces unnecessary constraints. Resource
allocation failures occur in many scenarios.
This patch will calculate whether the BT page size set by firmware is
sufficient before allocating BT, and increase the BT page size if it is
insufficient.
Fixes: 1133401412 ("RDMA/hns: Optimize base address table config flow for qp buffer")
Link: https://lore.kernel.org/r/20230512092245.344442-3-huangjunxian6@hisilicon.com
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58caa2a51a ]
On HIP08, the queried timeout attr is different from the timeout attr
configured by the user.
It is found by rdma-core testcase test_rdmacm_async_traffic:
======================================================================
FAIL: test_rdmacm_async_traffic (tests.test_rdmacm.CMTestCase)
----------------------------------------------------------------------
Traceback (most recent call last):
File "./tests/test_rdmacm.py", line 33, in test_rdmacm_async_traffic
self.two_nodes_rdmacm_traffic(CMAsyncConnection, self.rdmacm_traffic,
File "./tests/base.py", line 382, in two_nodes_rdmacm_traffic
raise(res)
AssertionError
Fixes: 926a01dc00 ("RDMA/hns: Add QP operations support for hip08 SoC")
Link: https://lore.kernel.org/r/20230512092245.344442-2-huangjunxian6@hisilicon.com
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 866422cddd ]
Device uses 4KB size blocks for user pages indirect list while the
driver creates those blocks with the size of PAGE_SIZE of the kernel. On
kernels with PAGE_SIZE different than 4KB (ARM RHEL), this leads to a
failure on register MR with indirect list because of the miss
communication between driver and device.
Fixes: 40909f664d ("RDMA/efa: Add EFA verbs implementation")
Link: https://lore.kernel.org/r/20230511115103.13876-1-ynachum@amazon.com
Reviewed-by: Firas Jahjah <firasj@amazon.com>
Reviewed-by: Michael Margolin <mrgolin@amazon.com>
Signed-off-by: Yonatan Nachum <ynachum@amazon.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08c7f09356 ]
Driver populates the list of pages used for Memory region wrongly when
page size is more than system page size. This is causing a failure when
some of the applications that creates MR with page size as 2M. Since HW
can support multiple page sizes, pass the correct page size while creating
the MR.
Also, driver need not adjust the number of pages when HW Queues are
created with user memory. It should work with the number of dma blocks
returned by ib_umem_num_dma_blocks. Fix this calculation also.
Fixes: 0c4dcd6028 ("RDMA/bnxt_re: Refactor hardware queue memory allocation")
Fixes: f6919d5638 ("RDMA/bnxt_re: Code refactor while populating user MRs")
Link: https://lore.kernel.org/r/1683484169-9539-1-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9b7c68b391 upstream.
Currently, offloaded conntrack entries (flows) can only be deleted
after they are removed from offload, which is either by timeout,
tcp state change or tc ct rule deletion. This can cause issues for
users wishing to manually delete or flush existing entries.
Support deletion of offloaded conntrack entries.
Example usage:
# Delete all offloaded (and non offloaded) conntrack entries
# whose source address is 1.2.3.4
$ conntrack -D -s 1.2.3.4
# Delete all entries
$ conntrack -F
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Cc: Demi Marie Obenour <demi@invisiblethingslab.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4badf2eb1e upstream.
Schedutil normally calls the adjust_perf callback for drivers with
adjust_perf callback available and fast_switch_possible flag set.
However, when frequency invariance is disabled and schedutil tries to
invoke fast_switch. So, there is a chance of kernel crash if this
function pointer is not set. To protect against this scenario add
fast_switch callback to amd_pstate driver.
Fixes: 1d215f0319 ("cpufreq: amd-pstate: Add fast switch function for AMD P-State")
Signed-off-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Signed-off-by: Wyes Karny <wyes.karny@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3bf8c6307b upstream.
Driver should update policy->cur after updating the frequency.
Currently amd_pstate doesn't update policy->cur when `adjust_perf`
is used. Which causes /proc/cpuinfo to show wrong cpu frequency.
Fix this by updating policy->cur with correct frequency value in
adjust_perf function callback.
- Before the fix: (setting min freq to 1.5 MHz)
[root@amd]# cat /proc/cpuinfo | grep "cpu MHz" | sort | uniq --count
1 cpu MHz : 1777.016
1 cpu MHz : 1797.160
1 cpu MHz : 1797.270
189 cpu MHz : 400.000
- After the fix: (setting min freq to 1.5 MHz)
[root@amd]# cat /proc/cpuinfo | grep "cpu MHz" | sort | uniq --count
1 cpu MHz : 1753.353
1 cpu MHz : 1756.838
1 cpu MHz : 1776.466
1 cpu MHz : 1776.873
1 cpu MHz : 1777.308
1 cpu MHz : 1779.900
183 cpu MHz : 1805.231
1 cpu MHz : 1956.815
1 cpu MHz : 2246.203
1 cpu MHz : 2259.984
Fixes: 1d215f0319 ("cpufreq: amd-pstate: Add fast switch function for AMD P-State")
Signed-off-by: Wyes Karny <wyes.karny@amd.com>
[ rjw: Subject edits ]
Cc: 5.17+ <stable@vger.kernel.org> # 5.17+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 000c2fa2c1 upstream.
Previously, channel open messages were always sent to monitors on the first
ioctl() call for unbound HCI sockets, even if the command and arguments
were completely invalid. This can leave an exploitable hole with the abuse
of invalid ioctl calls.
This commit hardens the ioctl processing logic by first checking if the
command is valid, and immediately returning with an ENOIOCTLCMD error code
if it is not. This ensures that ioctl calls with invalid commands are free
of side effects, and increases the difficulty of further exploitation by
forcing exploitation to find a way to pass a valid command first.
Signed-off-by: Ruihan Li <lrh2000@pku.edu.cn>
Co-developed-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Dragos-Marian Panait <dragos.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 71460c9ec5 ]
By default the VSC8501 and VSC8502 RGMII/GMII/MII RX_CLK output is
disabled. To allow packet forwarding towards the MAC it needs to be
enabled.
For other PHYs supported by this driver the clock output is enabled
by default.
Fixes: d316986331 ("net: phy: mscc: add support for VSC8502")
Signed-off-by: David Epping <david.epping@missinglinkelectronics.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 249b62c448 ]
amd_pstate active mode driver is only compatible with static governors.
Therefore it doesn't need fast_switch functionality. Remove
fast_switch_possible flag from amd_pstate active mode driver.
Fixes: ffa5096a7c ("cpufreq: amd-pstate: implement Pstate EPP support for the AMD processors")
Signed-off-by: Wyes Karny <wyes.karny@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4752354af7 ]
Check physical PFN is valid before converting the PFN to a struct page
pointer to be returned to caller of vfio_pin_pages().
vfio_pin_pages() pins user pages with contiguous IOVA.
If the IOVA of a user page to be pinned belongs to vma of vm_flags
VM_PFNMAP, pin_user_pages_remote() will return -EFAULT without returning
struct page address for this PFN. This is because usually this kind of PFN
(e.g. MMIO PFN) has no valid struct page address associated.
Upon this error, vaddr_get_pfns() will obtain the physical PFN directly.
While previously vfio_pin_pages() returns to caller PFN arrays directly,
after commit
34a255e676 ("vfio: Replace phys_pfn with pages for vfio_pin_pages()"),
PFNs will be converted to "struct page *" unconditionally and therefore
the returned "struct page *" array may contain invalid struct page
addresses.
Given current in-tree users of vfio_pin_pages() only expect "struct page *
returned, check PFN validity and return -EINVAL to let the caller be
aware of IOVAs to be pinned containing PFN not able to be returned in
"struct page *" array. So that, the caller will not consume the returned
pointer (e.g. test PageReserved()) and avoid error like "supervisor read
access in kernel mode".
Fixes: 34a255e676 ("vfio: Replace phys_pfn with pages for vfio_pin_pages()")
Cc: Sean Christopherson <seanjc@google.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Yan Zhao <yan.y.zhao@intel.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Link: https://lore.kernel.org/r/20230519065843.10653-1-yan.y.zhao@intel.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5c6de5fa0 ]
The read_skb() logic is incrementing the tcp->copied_seq which is used for
among other things calculating how many outstanding bytes can be read by
the application. This results in application errors, if the application
does an ioctl(FIONREAD) we return zero because this is calculated from
the copied_seq value.
To fix this we move tcp->copied_seq accounting into the recv handler so
that we update these when the recvmsg() hook is called and data is in
fact copied into user buffers. This gives an accurate FIONREAD value
as expected and improves ACK handling. Before we were calling the
tcp_rcv_space_adjust() which would update 'number of bytes copied to
user in last RTT' which is wrong for programs returning SK_PASS. The
bytes are only copied to the user when recvmsg is handled.
Doing the fix for recvmsg is straightforward, but fixing redirect and
SK_DROP pkts is a bit tricker. Build a tcp_psock_eat() helper and then
call this from skmsg handlers. This fixes another issue where a broken
socket with a BPF program doing a resubmit could hang the receiver. This
happened because although read_skb() consumed the skb through sock_drop()
it did not update the copied_seq. Now if a single reccv socket is
redirecting to many sockets (for example for lb) the receiver sk will be
hung even though we might expect it to continue. The hang comes from
not updating the copied_seq numbers and memory pressure resulting from
that.
We have a slight layer problem of calling tcp_eat_skb even if its not
a TCP socket. To fix we could refactor and create per type receiver
handlers. I decided this is more work than we want in the fix and we
already have some small tweaks depending on caller that use the
helper skb_bpf_strparser(). So we extend that a bit and always set
the strparser bit when it is in use and then we can gate the
seq_copied updates on this.
Fixes: 04919bed94 ("tcp: Introduce tcp_read_skb()")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/20230523025618.113937-9-john.fastabend@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6df7f764cd ]
When TCP stack has data ready to read sk_data_ready() is called. Sockmap
overwrites this with its own handler to call into BPF verdict program.
But, the original TCP socket had sock_def_readable that would additionally
wake up any user space waiters with sk_wake_async().
Sockmap saved the callback when the socket was created so call the saved
data ready callback and then we can wake up any epoll() logic waiting
on the read.
Note we call on 'copied >= 0' to account for returning 0 when a FIN is
received because we need to wake up user for this as well so they
can do the recvmsg() -> 0 and detect the shutdown.
Fixes: 04919bed94 ("tcp: Introduce tcp_read_skb()")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/20230523025618.113937-8-john.fastabend@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea444185a6 ]
A common mechanism to put a TCP socket into the sockmap is to hook the
BPF_SOCK_OPS_{ACTIVE_PASSIVE}_ESTABLISHED_CB event with a BPF program
that can map the socket info to the correct BPF verdict parser. When
the user adds the socket to the map the psock is created and the new
ops are assigned to ensure the verdict program will 'see' the sk_buffs
as they arrive.
Part of this process hooks the sk_data_ready op with a BPF specific
handler to wake up the BPF verdict program when data is ready to read.
The logic is simple enough (posted here for easy reading)
static void sk_psock_verdict_data_ready(struct sock *sk)
{
struct socket *sock = sk->sk_socket;
if (unlikely(!sock || !sock->ops || !sock->ops->read_skb))
return;
sock->ops->read_skb(sk, sk_psock_verdict_recv);
}
The oversight here is sk->sk_socket is not assigned until the application
accepts() the new socket. However, its entirely ok for the peer application
to do a connect() followed immediately by sends. The socket on the receiver
is sitting on the backlog queue of the listening socket until its accepted
and the data is queued up. If the peer never accepts the socket or is slow
it will eventually hit data limits and rate limit the session. But,
important for BPF sockmap hooks when this data is received TCP stack does
the sk_data_ready() call but the read_skb() for this data is never called
because sk_socket is missing. The data sits on the sk_receive_queue.
Then once the socket is accepted if we never receive more data from the
peer there will be no further sk_data_ready calls and all the data
is still on the sk_receive_queue(). Then user calls recvmsg after accept()
and for TCP sockets in sockmap we use the tcp_bpf_recvmsg_parser() handler.
The handler checks for data in the sk_msg ingress queue expecting that
the BPF program has already run from the sk_data_ready hook and enqueued
the data as needed. So we are stuck.
To fix do an unlikely check in recvmsg handler for data on the
sk_receive_queue and if it exists wake up data_ready. We have the sock
locked in both read_skb and recvmsg so should avoid having multiple
runners.
Fixes: 04919bed94 ("tcp: Introduce tcp_read_skb()")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/20230523025618.113937-7-john.fastabend@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 901546fd8f ]
The sockmap code is returning EAGAIN after a FIN packet is received and no
more data is on the receive queue. Correct behavior is to return 0 to the
user and the user can then close the socket. The EAGAIN causes many apps
to retry which masks the problem. Eventually the socket is evicted from
the sockmap because its released from sockmap sock free handling. The
issue creates a delay and can cause some errors on application side.
To fix this check on sk_msg_recvmsg side if length is zero and FIN flag
is set then set return to zero. A selftest will be added to check this
condition.
Fixes: 04919bed94 ("tcp: Introduce tcp_read_skb()")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: William Findlay <will@isovalent.com>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/20230523025618.113937-6-john.fastabend@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 405df89dd5 ]
We noticed some rare sk_buffs were stepping past the queue when system was
under memory pressure. The general theory is to skip enqueueing
sk_buffs when its not necessary which is the normal case with a system
that is properly provisioned for the task, no memory pressure and enough
cpu assigned.
But, if we can't allocate memory due to an ENOMEM error when enqueueing
the sk_buff into the sockmap receive queue we push it onto a delayed
workqueue to retry later. When a new sk_buff is received we then check
if that queue is empty. However, there is a problem with simply checking
the queue length. When a sk_buff is being processed from the ingress queue
but not yet on the sockmap msg receive queue its possible to also recv
a sk_buff through normal path. It will check the ingress queue which is
zero and then skip ahead of the pkt being processed.
Previously we used sock lock from both contexts which made the problem
harder to hit, but not impossible.
To fix instead of popping the skb from the queue entirely we peek the
skb from the queue and do the copy there. This ensures checks to the
queue length are non-zero while skb is being processed. Then finally
when the entire skb has been copied to user space queue or another
socket we pop it off the queue. This way the queue length check allows
bypassing the queue only after the list has been completely processed.
To reproduce issue we run NGINX compliance test with sockmap running and
observe some flakes in our testing that we attributed to this issue.
Fixes: 04919bed94 ("tcp: Introduce tcp_read_skb()")
Suggested-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: William Findlay <will@isovalent.com>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/20230523025618.113937-5-john.fastabend@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bce22552f9 ]
Now that the backlog manages the reschedule() logic correctly we can drop
the partial fix to reschedule from recvmsg hook.
Rescheduling on recvmsg hook was added to address a corner case where we
still had data in the backlog state but had nothing to kick it and
reschedule the backlog worker to run and finish copying data out of the
state. This had a couple limitations, first it required user space to
kick it introducing an unnecessary EBUSY and retry. Second it only
handled the ingress case and egress redirects would still be hung.
With the correct fix, pushing the reschedule logic down to where the
enomem error occurs we can drop this fix.
Fixes: bec217197b ("skmsg: Schedule psock work if the cached skb exists on the psock")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/20230523025618.113937-4-john.fastabend@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 29173d07f7 ]
Sk_buffs are fed into sockmap verdict programs either from a strparser
(when the user might want to decide how framing of skb is done by attaching
another parser program) or directly through tcp_read_sock. The
tcp_read_sock is the preferred method for performance when the BPF logic is
a stream parser.
The flow for Cilium's common use case with a stream parser is,
tcp_read_sock()
sk_psock_verdict_recv
ret = bpf_prog_run_pin_on_cpu()
sk_psock_verdict_apply(sock, skb, ret)
// if system is under memory pressure or app is slow we may
// need to queue skb. Do this queuing through ingress_skb and
// then kick timer to wake up handler
skb_queue_tail(ingress_skb, skb)
schedule_work(work);
The work queue is wired up to sk_psock_backlog(). This will then walk the
ingress_skb skb list that holds our sk_buffs that could not be handled,
but should be OK to run at some later point. However, its possible that
the workqueue doing this work still hits an error when sending the skb.
When this happens the skbuff is requeued on a temporary 'state' struct
kept with the workqueue. This is necessary because its possible to
partially send an skbuff before hitting an error and we need to know how
and where to restart when the workqueue runs next.
Now for the trouble, we don't rekick the workqueue. This can cause a
stall where the skbuff we just cached on the state variable might never
be sent. This happens when its the last packet in a flow and no further
packets come along that would cause the system to kick the workqueue from
that side.
To fix we could do simple schedule_work(), but while under memory pressure
it makes sense to back off some instead of continue to retry repeatedly. So
instead to fix convert schedule_work to schedule_delayed_work and add
backoff logic to reschedule from backlog queue on errors. Its not obvious
though what a good backoff is so use '1'.
To test we observed some flakes whil running NGINX compliance test with
sockmap we attributed these failed test to this bug and subsequent issue.
>From on list discussion. This commit
bec217197b41("skmsg: Schedule psock work if the cached skb exists on the psock")
was intended to address similar race, but had a couple cases it missed.
Most obvious it only accounted for receiving traffic on the local socket
so if redirecting into another socket we could still get an sk_buff stuck
here. Next it missed the case where copied=0 in the recv() handler and
then we wouldn't kick the scheduler. Also its sub-optimal to require
userspace to kick the internal mechanisms of sockmap to wake it up and
copy data to user. It results in an extra syscall and requires the app
to actual handle the EAGAIN correctly.
Fixes: 04919bed94 ("tcp: Introduce tcp_read_skb()")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: William Findlay <will@isovalent.com>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/20230523025618.113937-3-john.fastabend@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78fa0d61d9 ]
The read_skb hook calls consume_skb() now, but this means that if the
recv_actor program wants to use the skb it needs to inc the ref cnt
so that the consume_skb() doesn't kfree the sk_buff.
This is problematic because in some error cases under memory pressure
we may need to linearize the sk_buff from sk_psock_skb_ingress_enqueue().
Then we get this,
skb_linearize()
__pskb_pull_tail()
pskb_expand_head()
BUG_ON(skb_shared(skb))
Because we incremented users refcnt from sk_psock_verdict_recv() we
hit the bug on with refcnt > 1 and trip it.
To fix lets simply pass ownership of the sk_buff through the skb_read
call. Then we can drop the consume from read_skb handlers and assume
the verdict recv does any required kfree.
Bug found while testing in our CI which runs in VMs that hit memory
constraints rather regularly. William tested TCP read_skb handlers.
[ 106.536188] ------------[ cut here ]------------
[ 106.536197] kernel BUG at net/core/skbuff.c:1693!
[ 106.536479] invalid opcode: 0000 [#1] PREEMPT SMP PTI
[ 106.536726] CPU: 3 PID: 1495 Comm: curl Not tainted 5.19.0-rc5 #1
[ 106.537023] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS ArchLinux 1.16.0-1 04/01/2014
[ 106.537467] RIP: 0010:pskb_expand_head+0x269/0x330
[ 106.538585] RSP: 0018:ffffc90000138b68 EFLAGS: 00010202
[ 106.538839] RAX: 000000000000003f RBX: ffff8881048940e8 RCX: 0000000000000a20
[ 106.539186] RDX: 0000000000000002 RSI: 0000000000000000 RDI: ffff8881048940e8
[ 106.539529] RBP: ffffc90000138be8 R08: 00000000e161fd1a R09: 0000000000000000
[ 106.539877] R10: 0000000000000018 R11: 0000000000000000 R12: ffff8881048940e8
[ 106.540222] R13: 0000000000000003 R14: 0000000000000000 R15: ffff8881048940e8
[ 106.540568] FS: 00007f277dde9f00(0000) GS:ffff88813bd80000(0000) knlGS:0000000000000000
[ 106.540954] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 106.541227] CR2: 00007f277eeede64 CR3: 000000000ad3e000 CR4: 00000000000006e0
[ 106.541569] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 106.541915] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 106.542255] Call Trace:
[ 106.542383] <IRQ>
[ 106.542487] __pskb_pull_tail+0x4b/0x3e0
[ 106.542681] skb_ensure_writable+0x85/0xa0
[ 106.542882] sk_skb_pull_data+0x18/0x20
[ 106.543084] bpf_prog_b517a65a242018b0_bpf_skskb_http_verdict+0x3a9/0x4aa9
[ 106.543536] ? migrate_disable+0x66/0x80
[ 106.543871] sk_psock_verdict_recv+0xe2/0x310
[ 106.544258] ? sk_psock_write_space+0x1f0/0x1f0
[ 106.544561] tcp_read_skb+0x7b/0x120
[ 106.544740] tcp_data_queue+0x904/0xee0
[ 106.544931] tcp_rcv_established+0x212/0x7c0
[ 106.545142] tcp_v4_do_rcv+0x174/0x2a0
[ 106.545326] tcp_v4_rcv+0xe70/0xf60
[ 106.545500] ip_protocol_deliver_rcu+0x48/0x290
[ 106.545744] ip_local_deliver_finish+0xa7/0x150
Fixes: 04919bed94 ("tcp: Introduce tcp_read_skb()")
Reported-by: William Findlay <will@isovalent.com>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: William Findlay <will@isovalent.com>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/20230523025618.113937-2-john.fastabend@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3002b8642f ]
In fact the device with chip id 0xD283 is called NCT6126D, and that is
the chip id the Nuvoton code was written for. Correct that name to avoid
confusion, because a NCT6116D in fact exists as well but has another
chip id, and is currently not supported.
The look at the spec also revealed that GPIO group7 in fact has 8 pins,
so correct the pin count in that group as well.
Fixes: d0918a84af ("gpio-f7188x: Add GPIO support for Nuvoton NCT6116")
Reported-by: Xing Tong Wu <xingtong.wu@siemens.com>
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Acked-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c253dfc89 ]
devcom events are sent to all registered component. Following the
cited patch, it is possible for two components, e.g.: two eswitches,
to send devcom events, while both components are registered. This
means eswitch layer will do double un/pairing, which is double
allocation and free of resources, even though only one un/pairing is
needed. flow example:
cpu0 cpu1
---- ----
mlx5_devlink_eswitch_mode_set(dev0)
esw_offloads_devcom_init()
mlx5_devcom_register_component(esw0)
mlx5_devlink_eswitch_mode_set(dev1)
esw_offloads_devcom_init()
mlx5_devcom_register_component(esw1)
mlx5_devcom_send_event()
mlx5_devcom_send_event()
Hence, check whether the eswitches are already un/paired before
free/allocation of resources.
Fixes: 09b278462f ("net: devlink: enable parallel ops on netlink interface")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a431418f6 ]
This reverts commit 606e6a72e2 which exposes
the vnic diagnostic counters via debugfs. Instead, The upcoming series will
expose the same counters through devlink health reporter.
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Stable-dep-of: 8c253dfc89 ("net/mlx5: E-switch, Devcom, sync devcom events and devcom comp register")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e267b8a52c ]
This reverts commit 4fe1b3a5f8, which
exposes the steering dropped packets counter via debugfs. The upcoming
series will expose the counter via devlink health reporter instead
of debugfs.
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Stable-dep-of: 8c253dfc89 ("net/mlx5: E-switch, Devcom, sync devcom events and devcom comp register")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45dfbd9929 ]
For a bigjoiner configuration display->crtc_disable() will be called
first for the slave CRTCs and then for the master CRTC. However slave
CRTCs will be actually disabled only after the master CRTC is disabled
(from the encoder disable hooks called with the master CRTC state).
Hence the slave PIPEDMCs can be disabled only after the master CRTC is
disabled, make this so.
intel_encoders_post_pll_disable() must be called only for the master
CRTC, as for the other two encoder disable hooks. While at it fix this
up as well. This didn't cause a problem, since
intel_encoders_post_pll_disable() will call the corresponding hook only
for an encoder/connector connected to the given CRTC, however slave
CRTCs will have no associated encoder/connector.
Fixes: 3af2ff0840 ("drm/i915: Enable a PIPEDMC whenever its corresponding pipe is enabled")
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230510103131.1618266-2-imre.deak@intel.com
(cherry picked from commit 7eeef32719)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3acac2d06a ]
The spec requires disabling the PLL on TC ports before disconnecting the
port's PHY. Prepare for that by moving the PLL disabling to the CRTC
disable hook, while disconnecting the PHY will be moved to the
post_pll_disable() encoder hook in the next patch.
v2: Move the call from intel_crtc_disable_noatomic() as well.
Reviewed-by: Mika Kahola <mika.kahola@intel.com> # v1
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-27-imre.deak@intel.com
Stable-dep-of: 45dfbd9929 ("drm/i915: Fix PIPEDMC disabling for a bigjoiner configuration")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9025944fdd ]
Two dma_wmb() are added in the XDP TX path to ensure proper ordering of
descriptor and buffer updates:
1. A dma_wmb() is added after updating the last BD to make sure
the updates to rest of the descriptor are visible before
transferring ownership to FEC.
2. A dma_wmb() is also added after updating the bdp to ensure these
updates are visible before updating txq->bd.cur.
3. Start the xmit of the frame immediately right after configuring the
tx descriptor.
Fixes: 6d6b39f180 ("net: fec: add initial XDP support")
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 74836ec828 ]
When receive buffer is small, or the TCP rx queue looks too
complicated to bother using it directly - we allocate a new
skb and copy data into it.
We already use sk->sk_allocation... but nothing actually
sets it to GFP_ATOMIC on the ->sk_data_ready() path.
Users of HW offload are far more likely to experience problems
due to scheduling while atomic. "Copy mode" is very rarely
triggered with SW crypto.
Fixes: 84c61fe1a7 ("tls: rx: do not use the standard strparser")
Tested-by: Shai Amiram <samiram@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eca9bfafee ]
When receive buffer is small we try to copy out the data from
TCP into a skb maintained by TLS to prevent connection from
stalling. Unfortunately if a single record is made up of a mix
of decrypted and non-decrypted skbs combining them into a single
skb leads to loss of decryption status, resulting in decryption
errors or data corruption.
Similarly when trying to use TCP receive queue directly we need
to make sure that all the skbs within the record have the same
status. If we don't the mixed status will be detected correctly
but we'll CoW the anchor, again collapsing it into a single paged
skb without decrypted status preserved. So the "fixup" code will
not know which parts of skb to re-encrypt.
Fixes: 84c61fe1a7 ("tls: rx: do not use the standard strparser")
Tested-by: Shai Amiram <samiram@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1c607b1e5 ]
We'll need to copy input skbs individually in the next patch.
Factor that code out (without assuming we're copying a full record).
Tested-by: Shai Amiram <samiram@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: eca9bfafee ("tls: rx: strp: preserve decryption status of skbs when needed")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14c4be92eb ]
If a record is partially decrypted we'll have to CoW it, anyway,
so go into copy mode and allocate a writable skb right away.
This will make subsequent fix simpler because we won't have to
teach tls_strp_msg_make_copy() how to copy skbs while preserving
decrypt status.
Tested-by: Shai Amiram <samiram@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: eca9bfafee ("tls: rx: strp: preserve decryption status of skbs when needed")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b0c0dc9fb ]
We call tls_rx_msg_size(skb) before doing skb->len += chunk.
So the tls_rx_msg_size() code will see old skb->len, most
likely leading to an over-read.
Worst case we will over read an entire record, next iteration
will try to trim the skb but may end up turning frag len negative
or discarding the subsequent record (since we already told TCP
we've read it during previous read but now we'll trim it out of
the skb).
Fixes: 84c61fe1a7 ("tls: rx: do not use the standard strparser")
Tested-by: Shai Amiram <samiram@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 210620ae44 ]
alloc_skb_with_frags() fills in page frag sizes but does not
set skb->len and skb->data_len. Set those correctly otherwise
device offload will most likely generate an empty skb and
hit the BUG() at the end of __skb_nsg().
Fixes: 84c61fe1a7 ("tls: rx: do not use the standard strparser")
Tested-by: Shai Amiram <samiram@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3a03b540e ]
skb->len covers the entire skb, including the frag_list.
In fact we're guaranteed that rxm->full_len <= skb->len,
so since the change under Fixes we were not checking decrypt
status of any skb but the first.
Note that the skb_pagelen() added here may feel a bit costly,
but it's removed by subsequent fixes, anyway.
Reported-by: Tariq Toukan <tariqt@nvidia.com>
Fixes: 86b259f6f8 ("tls: rx: device: bound the frag walk")
Tested-by: Shai Amiram <samiram@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7dd3d9bd87 ]
If static allocation and dynamic allocation GPIOs are present,
dynamic allocation pollutes the numberspace for static allocation,
causing static allocation to fail.
Enforce dynamic allocation above GPIO_DYNAMIC_BASE.
Seen on a GTA04 when omap-gpio (static) and twl-gpio (dynamic)
raced:
[some successful registrations of omap_gpio instances]
[ 2.553833] twl4030_gpio twl4030-gpio: gpio (irq 145) chaining IRQs 161..178
[ 2.561401] gpiochip_find_base: found new base at 160
[ 2.564392] gpio gpiochip5: (twl4030): added GPIO chardev (254:5)
[ 2.564544] gpio gpiochip5: registered GPIOs 160 to 177 on twl4030
[...]
[ 2.692169] omap-gpmc 6e000000.gpmc: GPMC revision 5.0
[ 2.697357] gpmc_mem_init: disabling cs 0 mapped at 0x0-0x1000000
[ 2.703643] gpiochip_find_base: found new base at 178
[ 2.704376] gpio gpiochip6: (omap-gpmc): added GPIO chardev (254:6)
[ 2.704589] gpio gpiochip6: registered GPIOs 178 to 181 on omap-gpmc
[...]
[ 2.840393] gpio gpiochip7: Static allocation of GPIO base is deprecated, use dynamic allocation.
[ 2.849365] gpio gpiochip7: (gpio-160-191): GPIO integer space overlap, cannot add chip
[ 2.857513] gpiochip_add_data_with_key: GPIOs 160..191 (gpio-160-191) failed to register, -16
[ 2.866149] omap_gpio 48310000.gpio: error -EBUSY: Could not register gpio chip
On that device it is fixed invasively by
commit 92bf78b33b ("gpio: omap: use dynamic allocation of base")
but let's also fix that for devices where there is still
a mixture of static and dynamic allocation.
Fixes: 7b61212f2a ("gpiolib: Get rid of ARCH_NR_GPIOS")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: <christophe.leroy@csgroup.eu>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b54147fa37 ]
After suspend/resume cycle there is an error message and auto-mode
or CnQF stops working.
[ 5741.447511] amd-pmf AMDI0100:00: SMU cmd failed. err: 0xff
[ 5741.447523] amd-pmf AMDI0100:00: AMD_PMF_REGISTER_RESPONSE:ff
[ 5741.447527] amd-pmf AMDI0100:00: AMD_PMF_REGISTER_ARGUMENT:7
[ 5741.447531] amd-pmf AMDI0100:00: AMD_PMF_REGISTER_MESSAGE:16
[ 5741.447540] amd-pmf AMDI0100:00: [AUTO_MODE] avg power: 0 mW mode: QUIET
This is because the DRAM address used for accessing metrics table
needs to be refreshed after a suspend resume cycle. Add a resume
callback to reset this again.
Fixes: 1a409b35c9 ("platform/x86/amd/pmf: Get performance metrics from PMFW")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230513011408.958-1-mario.limonciello@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f5486b620 ]
When building sign-file, the call to get the CFLAGS for libcrypto is
missing white-space between `pkg-config` and `--cflags`:
$(shell $(HOSTPKG_CONFIG)--cflags libcrypto 2> /dev/null)
Removing the redirection of stderr, we see:
$ make -C tools/testing/selftests/bpf sign-file
make: Entering directory '[...]/tools/testing/selftests/bpf'
make: pkg-config--cflags: No such file or directory
SIGN-FILE sign-file
make: Leaving directory '[...]/tools/testing/selftests/bpf'
Add the missing space.
Fixes: fc97590668 ("selftests/bpf: Add test for bpf_verify_pkcs7_signature() kfunc")
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Roberto Sassu <roberto.sassu@huawei.com>
Link: https://lore.kernel.org/bpf/20230426215032.415792-1-jeremy@azazel.net
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 892943d772 ]
According to Renesas Electronics (formerly Dialog Semiconductor), the
standard AUTO mode of the PMIC DA9061 can lead to stability problems
depending on the hardware revision. It is recommended to set a defined
mode such as PFM or PWM permanently. So set and limit the mode for
buck 1, 2 and 3 to a fixed one.
Fixes: 611b6c891e ("ARM: dts: imx6ull-dhcom: Add DH electronics DHCOM i.MX6ULL SoM and PDK2 board")
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c329f5da7 ]
Spi geni driver switches between FIFO and DMA modes based on xfer length.
FIFO mode relies on M_CMD_DONE_EN interrupt for completion while DMA mode
relies on XX_DMA_DONE.
During dynamic switching, if FIFO mode is chosen, FIFO related interrupts
are enabled and DMA related interrupts are disabled. And viceversa.
Chip select shares M_CMD_DONE_EN interrupt with FIFO to check completion.
Now, if a chip select operation is preceded by a DMA xfer, M_CMD_DONE_EN
interrupt would have been disabled and hence it will never receive one
resulting in timeout.
For chip select, in addition to setting the xfer mode to FIFO,
select_mode() to FIFO so that required interrupts are enabled.
Fixes: e5f0dfa78a ("spi: spi-geni-qcom: Add support for SE DMA mode")
Suggested-by: Praveen Talari <quic_ptalari@quicinc.com
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com
Reviewed-by: Douglas Anderson <dianders@chromium.org
Link: https://lore.kernel.org/r/1683626496-9685-1-git-send-email-quic_vnivarth@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c6e045361a ]
Commit bb1be74985 ("firmware: arm_ffa: Add v1.1 get_partition_info support")
adds support to discovery the UUIDs of the partitions or just fetch the
partition count using the PARTITION_INFO_GET_RETURN_COUNT_ONLY flag.
However the commit doesn't handle the fact that the older version doesn't
understand the flag and must be MBZ which results in firmware returning
invalid parameter error. That results in the failure of the driver probe
which is in correct.
Limit the usage of the PARTITION_INFO_GET_RETURN_COUNT_ONLY flag for the
versions above v1.0(i.e v1.1 and onwards) which fixes the issue.
Fixes: bb1be74985 ("firmware: arm_ffa: Add v1.1 get_partition_info support")
Reported-by: Jens Wiklander <jens.wiklander@linaro.org>
Reported-by: Marc Bonnici <marc.bonnici@arm.com>
Tested-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Link: https://lore.kernel.org/r/20230419-ffa_fixes_6-4-v2-2-d9108e43a176@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44e8d5ad2d ]
scmi_xfer_raw_worker_init() is specifying a flag, WQ_SYSFS, as @max_active.
Fix it by or'ing WQ_SYSFS into @flags so that it actually enables sysfs
interface and using 0 for @max_active for the default setting.
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: 3c3d818a93 ("firmware: arm_scmi: Add core raw transmission support")
Link: https://lore.kernel.org/r/ZEGTnajiQm7mkkZS@slm.duckdns.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 04910d8cbf upstream.
The commit c6d96df9fa ("net: ethernet: mtk_eth_soc: drop generic vlan rx
offload, only use DSA untagging") makes VLAN RX offloading to be only used
on the SoCs without the MTK_NETSYS_V2 ability (which are not just MT7621
and MT7622). The commit disables the proper handling of special tagged
(DSA) frames, added with commit 87e3df4961 ("net-next: ethernet:
mediatek: add CDM able to recognize the tag for DSA"), for non
MTK_NETSYS_V2 SoCs when it finds a MAC that does not use DSA. So if the
other MAC uses DSA, the CDMQ component transmits DSA tagged frames to the
CPU improperly. This issue can be observed on frames with TCP, for example,
a TCP speed test using iperf3 won't work.
The commit disables the proper handling of special tagged (DSA) frames
because it assumes that these SoCs don't use more than one MAC, which is
wrong. Although I made Frank address this false assumption on the patch log
when they sent the patch on behalf of Felix, the code still made changes
with this assumption.
Therefore, the proper handling of special tagged (DSA) frames must be kept
enabled in all circumstances as it doesn't affect non DSA tagged frames.
Hardware DSA untagging, introduced with the commit 2d7605a729 ("net:
ethernet: mtk_eth_soc: enable hardware DSA untagging"), and VLAN RX
offloading are operations on the two CDM components of the frame engine,
CDMP and CDMQ, which connect to Packet DMA (PDMA) and QoS DMA (QDMA) and
are between the MACs and the CPU. These operations apply to all MACs of the
SoC so if one MAC uses DSA and the other doesn't, the hardware DSA
untagging operation will cause the CDMP component to transmit non DSA
tagged frames to the CPU improperly.
Since the VLAN RX offloading feature configuration was dropped, VLAN RX
offloading can only be used along with hardware DSA untagging. So, for the
case above, we need to disable both features and leave it to the CPU,
therefore software, to untag the DSA and VLAN tags.
So the correct way to handle this is:
For all SoCs:
Enable the proper handling of special tagged (DSA) frames
(MTK_CDMQ_IG_CTRL).
For non MTK_NETSYS_V2 SoCs:
Enable hardware DSA untagging (MTK_CDMP_IG_CTRL).
Enable VLAN RX offloading (MTK_CDMP_EG_CTRL).
When a non MTK_NETSYS_V2 SoC MAC does not use DSA:
Disable hardware DSA untagging (MTK_CDMP_IG_CTRL).
Disable VLAN RX offloading (MTK_CDMP_EG_CTRL).
Fixes: c6d96df9fa ("net: ethernet: mtk_eth_soc: drop generic vlan rx offload, only use DSA untagging")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 368d3cb406 upstream.
page_pool_ring_[un]lock() use in_softirq() to decide which
spin lock variant to use, and when they are called in the
context with in_softirq() being false, spin_lock_bh() is
called in page_pool_ring_lock() while spin_unlock() is
called in page_pool_ring_unlock(), because spin_lock_bh()
has disabled the softirq in page_pool_ring_lock(), which
causes inconsistency for spin lock pair calling.
This patch fixes it by returning in_softirq state from
page_pool_producer_lock(), and use it to decide which
spin lock variant to use in page_pool_producer_unlock().
As pool->ring has both producer and consumer lock, so
rename it to page_pool_producer_[un]lock() to reflect
the actual usage. Also move them to page_pool.c as they
are only used there, and remove the 'inline' as the
compiler may have better idea to do inlining or not.
Fixes: 7886244736 ("net: page_pool: Add bulk support for ptr_ring")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Link: https://lore.kernel.org/r/20230522031714.5089-1-linyunsheng@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3511227167 upstream.
We found a crash when using SMCRv2 with 2 Mellanox ConnectX-4. It
can be reproduced by:
- smc_run nginx
- smc_run wrk -t 32 -c 500 -d 30 http://<ip>:<port>
BUG: kernel NULL pointer dereference, address: 0000000000000014
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 8000000108713067 P4D 8000000108713067 PUD 151127067 PMD 0
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 4 PID: 2441 Comm: kworker/4:249 Kdump: loaded Tainted: G W E 6.4.0-rc1+ #42
Workqueue: smc_hs_wq smc_listen_work [smc]
RIP: 0010:smc_clc_send_confirm_accept+0x284/0x580 [smc]
RSP: 0018:ffffb8294b2d7c78 EFLAGS: 00010a06
RAX: ffff8f1873238880 RBX: ffffb8294b2d7dc8 RCX: 0000000000000000
RDX: 00000000000000b4 RSI: 0000000000000001 RDI: 0000000000b40c00
RBP: ffffb8294b2d7db8 R08: ffff8f1815c5860c R09: 0000000000000000
R10: 0000000000000400 R11: 0000000000000000 R12: ffff8f1846f56180
R13: ffff8f1815c5860c R14: 0000000000000001 R15: 0000000000000001
FS: 0000000000000000(0000) GS:ffff8f1aefd00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000014 CR3: 00000001027a0001 CR4: 00000000003706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
? mlx5_ib_map_mr_sg+0xa1/0xd0 [mlx5_ib]
? smcr_buf_map_link+0x24b/0x290 [smc]
? __smc_buf_create+0x4ee/0x9b0 [smc]
smc_clc_send_accept+0x4c/0xb0 [smc]
smc_listen_work+0x346/0x650 [smc]
? __schedule+0x279/0x820
process_one_work+0x1e5/0x3f0
worker_thread+0x4d/0x2f0
? __pfx_worker_thread+0x10/0x10
kthread+0xe5/0x120
? __pfx_kthread+0x10/0x10
ret_from_fork+0x2c/0x50
</TASK>
During the CLC handshake, server sequentially tries available SMCRv2
and SMCRv1 devices in smc_listen_work().
If an SMCRv2 device is found. SMCv2 based link group and link will be
assigned to the connection. Then assumed that some buffer assignment
errors happen later in the CLC handshake, such as RMB registration
failure, server will give up SMCRv2 and try SMCRv1 device instead. But
the resources assigned to the connection won't be reset.
When server tries SMCRv1 device, the connection creation process will
be executed again. Since conn->lnk has been assigned when trying SMCRv2,
it will not be set to the correct SMCRv1 link in
smcr_lgr_conn_assign_link(). So in such situation, conn->lgr points to
correct SMCRv1 link group but conn->lnk points to the SMCRv2 link
mistakenly.
Then in smc_clc_send_confirm_accept(), conn->rmb_desc->mr[link->link_idx]
will be accessed. Since the link->link_idx is not correct, the related
MR may not have been initialized, so crash happens.
| Try SMCRv2 device first
| |-> conn->lgr: assign existed SMCRv2 link group;
| |-> conn->link: assign existed SMCRv2 link (link_idx may be 1 in SMC_LGR_SYMMETRIC);
| |-> sndbuf & RMB creation fails, quit;
|
| Try SMCRv1 device then
| |-> conn->lgr: create SMCRv1 link group and assign;
| |-> conn->link: keep SMCRv2 link mistakenly;
| |-> sndbuf & RMB creation succeed, only RMB->mr[link_idx = 0]
| initialized.
|
| Then smc_clc_send_confirm_accept() accesses
| conn->rmb_desc->mr[conn->link->link_idx, which is 1], then crash.
v
This patch tries to fix this by cleaning conn->lnk before assigning
link. In addition, it is better to reset the connection and clean the
resources assigned if trying SMCRv2 failed in buffer creation or
registration.
Fixes: e49300a6bf ("net/smc: add listen processing for SMC-Rv2")
Link: https://lore.kernel.org/r/20220523055056.2078994-1-liuyacan@corp.netease.com/
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 111a833dc5 upstream.
The transmit buffers allocated by the driver can be used to transmit data
by any messages/commands needing the buffer. However, it is not guaranteed
to have been zero-ed before every new transmission and hence it will just
contain residual value from the previous transmission. There are several
reserved fields in the memory descriptors that must be zero(MBZ). The
receiver can reject the transmission if any such MBZ fields are non-zero.
While we can set the whole page to zero, it is not optimal as most of the
fields get initialised to the value required for the current transmission.
So, just set the reserved/MBZ fields to zero in the memory descriptors
explicitly to honour the requirement and keep the receiver happy.
Fixes: cc2195fe53 ("firmware: arm_ffa: Add support for MEM_* interfaces")
Reported-by: Marc Bonnici <marc.bonnici@arm.com>
Link: https://lore.kernel.org/r/20230503131252.12585-1-sudeep.holla@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f161cea5a2 upstream.
While testing the ethernet interface on a Variscite symphony carrier
board using an imx8mn SOM with an onboard ADIN1300 PHY (EC hardware
configuration), the ethernet PHY is not detected.
The ADIN1300 datasheet indicate that the "Management interface
active (t4)" state is reached at most 5ms after the reset signal is
deasserted.
The device tree in Variscite custom git repository uses the following
property:
phy-reset-post-delay = <20>;
Add a new MDIO property 'reset-deassert-us' of 20ms to have the same
delay inside the ethphy node. Adding this property fixes the problem
with the PHY detection.
Note that this SOM can also have an Atheros AR8033 PHY. In this case,
a 1ms deassert delay is sufficient. Add a comment to that effect.
Fixes: ade0176dd8 ("arm64: dts: imx8mn-var-som: Add Variscite VAR-SOM-MX8MN System on Module")
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f893f57a3 upstream.
From one hand, mlx5 driver is allowing to probe PFs in parallel.
From the other hand, devcom, which is a share resource between PFs, is
registered without any lock. This might resulted in memory problems.
Hence, use the global mlx5_dev_list_lock in order to serialize devcom
registration.
Fixes: fadd59fc50 ("net/mlx5: Introduce inter-device communication mechanism")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af87194352 upstream.
In case devcom allocation is failed, mlx5 is always freeing the priv.
However, this priv might have been allocated by a different thread,
and freeing it might lead to use-after-free bugs.
Fix it by freeing the priv only in case it was allocated by the
running thread.
Fixes: fadd59fc50 ("net/mlx5: Introduce inter-device communication mechanism")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a0a935fb6 upstream.
DEVX can issue a general command, which is not used by mlx5 driver.
In case such command is failed, mlx5 is trying to collect the failure
data, However, mlx5 doesn't create a storage for this command, since
mlx5 doesn't use it. This lead to array-index-out-of-bounds error.
Fix it by checking whether the command is known before collecting the
failure data.
Fixes: 34f46ae0d4 ("net/mlx5: Add command failures data to debugfs")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c7dd225bc2 upstream.
SW Steering uses RC QP for writing STEs to ICM. This writingis done in LB
(loopback), and FL (force-loopback) QP is preferred for performance. FL is
available when RoCE is enabled or disabled based on RoCE caps.
This patch adds reading of FL capability from HCA caps in addition to the
existing reading from RoCE caps, thus fixing the case where we didn't
have loopback enabled when RoCE was disabled.
Fixes: 7304d603a5 ("net/mlx5: DR, Add support for force-loopback QP")
Signed-off-by: Itamar Gozlan <igozlan@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2be5bd42a5 upstream.
In case user switch a device from switchdev mode to legacy mode, mlx5
first unpair the E-switch and afterwards unload the uplink vport.
From the other hand, in case user remove or reload a device, mlx5
first unload the uplink vport and afterwards unpair the E-switch.
The latter is causing a bug[1], hence, handle pairing of E-switch as
part of uplink un/load APIs.
[1]
In case VF_LAG is used, every tc fdb flow is duplicated to the peer
esw. However, the original esw keeps a pointer to this duplicated
flow, not the peer esw.
e.g.: if user create tc fdb flow over esw0, the flow is duplicated
over esw1, in FW/HW, but in SW, esw0 keeps a pointer to the duplicated
flow.
During module unload while a peer tc fdb flow is still offloaded, in
case the first device to be removed is the peer device (esw1 in the
example above), the peer net-dev is destroyed, and so the mlx5e_priv
is memset to 0.
Afterwards, the peer device is trying to unpair himself from the
original device (esw0 in the example above). Unpair API invoke the
original device to clear peer flow from its eswitch (esw0), but the
peer flow, which is stored over the original eswitch (esw0), is
trying to use the peer mlx5e_priv, which is memset to 0 and result in
bellow kernel-oops.
[ 157.964081 ] BUG: unable to handle page fault for address: 000000000002ce60
[ 157.964662 ] #PF: supervisor read access in kernel mode
[ 157.965123 ] #PF: error_code(0x0000) - not-present page
[ 157.965582 ] PGD 0 P4D 0
[ 157.965866 ] Oops: 0000 [#1] SMP
[ 157.967670 ] RIP: 0010:mlx5e_tc_del_fdb_flow+0x48/0x460 [mlx5_core]
[ 157.976164 ] Call Trace:
[ 157.976437 ] <TASK>
[ 157.976690 ] __mlx5e_tc_del_fdb_peer_flow+0xe6/0x100 [mlx5_core]
[ 157.977230 ] mlx5e_tc_clean_fdb_peer_flows+0x67/0x90 [mlx5_core]
[ 157.977767 ] mlx5_esw_offloads_unpair+0x2d/0x1e0 [mlx5_core]
[ 157.984653 ] mlx5_esw_offloads_devcom_event+0xbf/0x130 [mlx5_core]
[ 157.985212 ] mlx5_devcom_send_event+0xa3/0xb0 [mlx5_core]
[ 157.985714 ] esw_offloads_disable+0x5a/0x110 [mlx5_core]
[ 157.986209 ] mlx5_eswitch_disable_locked+0x152/0x170 [mlx5_core]
[ 157.986757 ] mlx5_eswitch_disable+0x51/0x80 [mlx5_core]
[ 157.987248 ] mlx5_unload+0x2a/0xb0 [mlx5_core]
[ 157.987678 ] mlx5_uninit_one+0x5f/0xd0 [mlx5_core]
[ 157.988127 ] remove_one+0x64/0xe0 [mlx5_core]
[ 157.988549 ] pci_device_remove+0x31/0xa0
[ 157.988933 ] device_release_driver_internal+0x18f/0x1f0
[ 157.989402 ] driver_detach+0x3f/0x80
[ 157.989754 ] bus_remove_driver+0x70/0xf0
[ 157.990129 ] pci_unregister_driver+0x34/0x90
[ 157.990537 ] mlx5_cleanup+0xc/0x1c [mlx5_core]
[ 157.990972 ] __x64_sys_delete_module+0x15a/0x250
[ 157.991398 ] ? exit_to_user_mode_prepare+0xea/0x110
[ 157.991840 ] do_syscall_64+0x3d/0x90
[ 157.992198 ] entry_SYSCALL_64_after_hwframe+0x46/0xb0
Fixes: 04de7dda73 ("net/mlx5e: Infrastructure for duplicated offloading of TC flows")
Fixes: 1418ddd96a ("net/mlx5e: Duplicate offloaded TC eswitch rules under uplink LAG")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e5daf5565 upstream.
When calculating crc for hash index we use the function crc32 that
calculates for little-endian (LE) arch.
Then we convert it to network endianness using htonl(), but it's wrong
to do the conversion in BE archs since the crc32 value is already LE.
The solution is to switch the bytes from the crc result for all types
of arc.
Fixes: 40416d8ede ("net/mlx5: DR, Replace CRC32 implementation to use kernel lib")
Signed-off-by: Erez Shitrit <erezsh@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit afbed3f748 upstream.
NAPI gets called with budget of 0 from netpoll, which has interrupts
disabled. We should try to free some space on Tx rings and nothing
else.
Specifically do not try to handle XDP TX or try to refill Rx buffers -
we can't use the page pool from IRQ context. Don't check if IRQs moved,
either, that makes no sense in netpoll. Netpoll calls _all_ the rings
from whatever CPU it happens to be invoked on.
In general do as little as possible, the work quickly adds up when
there's tens of rings to poll.
The immediate stack trace I was seeing is:
__do_softirq+0xd1/0x2c0
__local_bh_enable_ip+0xc7/0x120
</IRQ>
<TASK>
page_pool_put_defragged_page+0x267/0x320
mlx5e_free_xdpsq_desc+0x99/0xd0
mlx5e_poll_xdpsq_cq+0x138/0x3b0
mlx5e_napi_poll+0xc3/0x8b0
netpoll_poll_dev+0xce/0x150
AFAIU page pool takes a BH lock, releases it and since BH is now
enabled tries to run softirqs.
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Fixes: 60bbf7eeef ("mlx5: use page_pool for xdp_return_frame call")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit be071cdb16 upstream.
With introduction of post action infrastructure most of the users of encap
attribute had been modified in order to obtain the correct attribute by
calling mlx5e_tc_get_encap_attr() helper instead of assuming encap action
is always on default attribute. However, the cited commit didn't modify
mlx5e_invalidate_encap() which prevents it from destroying correct modify
header action which leads to a warning [0]. Fix the issue by using correct
attribute.
[0]:
Feb 21 09:47:35 c-237-177-40-045 kernel: WARNING: CPU: 17 PID: 654 at drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:684 mlx5e_tc_attach_mod_hdr+0x1cc/0x230 [mlx5_core]
Feb 21 09:47:35 c-237-177-40-045 kernel: RIP: 0010:mlx5e_tc_attach_mod_hdr+0x1cc/0x230 [mlx5_core]
Feb 21 09:47:35 c-237-177-40-045 kernel: Call Trace:
Feb 21 09:47:35 c-237-177-40-045 kernel: <TASK>
Feb 21 09:47:35 c-237-177-40-045 kernel: mlx5e_tc_fib_event_work+0x8e3/0x1f60 [mlx5_core]
Feb 21 09:47:35 c-237-177-40-045 kernel: ? mlx5e_take_all_encap_flows+0xe0/0xe0 [mlx5_core]
Feb 21 09:47:35 c-237-177-40-045 kernel: ? lock_downgrade+0x6d0/0x6d0
Feb 21 09:47:35 c-237-177-40-045 kernel: ? lockdep_hardirqs_on_prepare+0x273/0x3f0
Feb 21 09:47:35 c-237-177-40-045 kernel: ? lockdep_hardirqs_on_prepare+0x273/0x3f0
Feb 21 09:47:35 c-237-177-40-045 kernel: process_one_work+0x7c2/0x1310
Feb 21 09:47:35 c-237-177-40-045 kernel: ? lockdep_hardirqs_on_prepare+0x3f0/0x3f0
Feb 21 09:47:35 c-237-177-40-045 kernel: ? pwq_dec_nr_in_flight+0x230/0x230
Feb 21 09:47:35 c-237-177-40-045 kernel: ? rwlock_bug.part.0+0x90/0x90
Feb 21 09:47:35 c-237-177-40-045 kernel: worker_thread+0x59d/0xec0
Feb 21 09:47:35 c-237-177-40-045 kernel: ? __kthread_parkme+0xd9/0x1d0
Fixes: 8300f22526 ("net/mlx5e: Create new flow attr for multi table actions")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7aa5038019 upstream.
Check in the mlx5e_ptp_poll_ts_cq context if the ptp tx sq should be woken
up. Before change, the ptp tx sq may never wake up if the ptp tx ts skb
fifo is full when mlx5e_poll_tx_cq checks if the queue should be woken up.
Fixes: 1880bc4e4a ("net/mlx5e: Add TX port timestamp support")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ca328e985 upstream.
When doing plpmtu probe, the probe size is growing every time when it
receives the ACK during the Search state until the probe fails. When
the failure occurs, pl.probe_high is set and it goes to the Complete
state.
However, if the link pmtu is huge, like 65535 in loopback_dev, the probe
eventually keeps using SCTP_MAX_PLPMTU as the probe size and never fails.
Because of that, pl.probe_high can not be set, and the plpmtu probe can
never go to the Complete state.
Fix it by setting pl.probe_high to SCTP_MAX_PLPMTU when the probe size
grows to SCTP_MAX_PLPMTU in sctp_transport_pl_recv(). Also, not allow
the probe size greater than SCTP_MAX_PLPMTU in the Complete state.
Fixes: b87641aff9 ("sctp: do state transition when a probe succeeds on HB ACK recv path")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e764f12208 upstream.
Move cxl_await_media_ready() to cxl_pci probe before driver starts issuing
IDENTIFY and retrieving memory device information to ensure that the
device is ready to provide the information. Allow cxl_pci_probe() to succeed
even if media is not ready. Cache the media failure in cxlds and don't ask
the device for any media information.
The rationale for proceeding in the !media_ready case is to allow for
mailbox operations to interrogate and/or remediate the device. After
media is repaired then rebinding the cxl_pci driver is expected to
restart the capacity scan.
Suggested-by: Dan Williams <dan.j.williams@intel.com>
Fixes: b39cb1052a ("cxl/mem: Register CXL memX devices")
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/168445310026.3251520.8124296540679268206.stgit@djiang5-mobl3
[djbw: fixup cxl_test]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce17ad0d54 upstream.
The Memory_Info_Valid bit (CXL 3.0 8.1.3.8.2) indicates that the CXL
Range Size High and Size Low registers are valid. The bit must be set
within 1 second of reset deassertion to the device. Check valid bit
before we check the Memory_Active bit when waiting for
cxl_await_media_ready() to ensure that the memory info is valid for
consumption. Also ensures both DVSEC ranges 1 and 2 are ready if DVSEC
Capability indicates they are both supported.
Fixes: 523e594d9c ("cxl/pci: Implement wait for media active")
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/168444687469.3134781.11033518965387297327.stgit@djiang5-mobl3
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e4be0d011 upstream.
The commit e335bb51cc ("x86/unwind: Ensure stack pointer is aligned")
tried to align the stack pointer in show_trace_log_lvl(), otherwise the
"stack < stack_info.end" check can't guarantee that the last read does
not go past the end of the stack.
However, we have the same problem with the initial value of the stack
pointer, it can also be unaligned. So without this patch this trivial
kernel module
#include <linux/module.h>
static int init(void)
{
asm volatile("sub $0x4,%rsp");
dump_stack();
asm volatile("add $0x4,%rsp");
return -EAGAIN;
}
module_init(init);
MODULE_LICENSE("GPL");
crashes the kernel.
Fixes: e335bb51cc ("x86/unwind: Ensure stack pointer is aligned")
Signed-off-by: Vernon Lovejoy <vlovejoy@redhat.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Link: https://lore.kernel.org/r/20230512104232.GA10227@redhat.com
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 335b422346 upstream.
Commit bf5e758f02 ("genirq/msi: Simplify sysfs handling") reworked the
creation of sysfs entries for MSI IRQs. The creation used to be in
msi_domain_alloc_irqs_descs_locked after calling ops->domain_alloc_irqs.
Then it moved into __msi_domain_alloc_irqs which is an implementation of
domain_alloc_irqs. However, Xen comes with the only other implementation
of domain_alloc_irqs and hence doesn't run the sysfs population code
anymore.
Commit 6c796996ee ("x86/pci/xen: Fixup fallout from the PCI/MSI
overhaul") set the flag MSI_FLAG_DEV_SYSFS for the xen msi_domain_info
but that doesn't actually have an effect because Xen uses it's own
domain_alloc_irqs implementation.
Fix this by making use of the fallback functions for sysfs population.
Fixes: bf5e758f02 ("genirq/msi: Simplify sysfs handling")
Signed-off-by: Maximilian Heyne <mheyne@amazon.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20230503131656.15928-1-mheyne@amazon.de
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 91aa4b3782 upstream.
This worked before by coincidence, as the regulator was probed and enabled
before PCI RC probe. But probe order changed since commit 259b93b21a
("regulator: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in
4.14") and PCIe supply is enabled after RC.
Fix this by adding the regulator to RC node.
The PCIe vaux regulator still needs to be enabled unconditionally for
Mini-PCIe USB-only devices.
Fixes: ef3846247b ("ARM: dts: imx6qdl: add TQ-Systems MBa6x device trees")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f67bc15e52 upstream.
This code generates a Smatch warning:
drivers/hwtracing/coresight/coresight-tmc-etr.c:947 tmc_etr_buf_insert_barrier_packet()
error: uninitialized symbol 'bufp'.
The problem is that if tmc_sg_table_get_data() returns -EINVAL, then
when we test if "len < CORESIGHT_BARRIER_PKT_SIZE", the negative "len"
value is type promoted to a high unsigned long value which is greater
than CORESIGHT_BARRIER_PKT_SIZE. Fix this bug by adding an explicit
check for error codes.
Fixes: 75f4e3619f ("coresight: tmc-etr: Add transparent buffer management")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/7d33e244-d8b9-4c27-9653-883a13534b01@kili.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bbb320bfe2 upstream.
Stop restricting the PCI search to a range of PCI domains fed to
pci_get_domain_bus_and_slot(). Instead, use for_each_pci_dev() and
look at all PCI domains in one pass.
On systems with more than 8 sockets, this avoids error messages like
"Information: Invalid level, Can't get TDP control information at
specified levels on cpu 480" from the intel speed select utility.
Fixes: aa2ddd2425 ("platform/x86: ISST: Use numa node id for cpu pci dev mapping")
Signed-off-by: Steve Wahl <steve.wahl@hpe.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230519160420.2588475-1-steve.wahl@hpe.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f15afbd34d upstream.
Shifting signed 32-bit value by 31 bits is undefined, so changing
significant bit to unsigned. It was spotted by UBSAN.
So let's just fix this by using the BIT() helper for all SB_* flags.
Fixes: e462ec50cb ("VFS: Differentiate mount flags (MS_*) from internal superblock flags")
Signed-off-by: Hao Ge <gehao@kylinos.cn>
Message-Id: <20230424051835.374204-1-gehao@kylinos.cn>
[brauner@kernel.org: use BIT() for all SB_* flags]
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 19b8766459 upstream.
Each physical partition can provide multiple services each with UUID.
Each such service can be presented as logical partition with a unique
combination of VM ID and UUID. The number of distinct UUID in a system
will be less than or equal to the number of logical partitions.
However, currently it fails to register more than one logical partition
or service within a physical partition as the device name contains only
VM ID while both VM ID and UUID are maintained in the partition information.
The kernel complains with the below message:
| sysfs: cannot create duplicate filename '/devices/arm-ffa-8001'
| CPU: 1 PID: 1 Comm: swapper/0 Not tainted 6.3.0-rc7 #8
| Hardware name: FVP Base RevC (DT)
| Call trace:
| dump_backtrace+0xf8/0x118
| show_stack+0x18/0x24
| dump_stack_lvl+0x50/0x68
| dump_stack+0x18/0x24
| sysfs_create_dir_ns+0xe0/0x13c
| kobject_add_internal+0x220/0x3d4
| kobject_add+0x94/0x100
| device_add+0x144/0x5d8
| device_register+0x20/0x30
| ffa_device_register+0x88/0xd8
| ffa_setup_partitions+0x108/0x1b8
| ffa_init+0x2ec/0x3a4
| do_one_initcall+0xcc/0x240
| do_initcall_level+0x8c/0xac
| do_initcalls+0x54/0x94
| do_basic_setup+0x1c/0x28
| kernel_init_freeable+0x100/0x16c
| kernel_init+0x20/0x1a0
| ret_from_fork+0x10/0x20
| kobject_add_internal failed for arm-ffa-8001 with -EEXIST, don't try to
| register things with the same name in the same directory.
| arm_ffa arm-ffa: unable to register device arm-ffa-8001 err=-17
| ARM FF-A: ffa_setup_partitions: failed to register partition ID 0x8001
By virtue of being random enough to avoid collisions when generated in a
distributed system, there is no way to compress UUID keys to the number
of bits required to identify each. We can eliminate '-' in the name but
it is not worth eliminating 4 bytes and add unnecessary logic for doing
that. Also v1.0 doesn't provide the UUID of the partitions which makes
it hard to use the same for the device name.
So to keep it simple, let us alloc an ID using ida_alloc() and append the
same to "arm-ffa" to make up a unique device name. Also stash the id value
in ffa_dev to help freeing the ID later when the device is destroyed.
Fixes: e781858488 ("firmware: arm_ffa: Add initial FFA bus support for device enumeration")
Reported-by: Lucian Paul-Trifu <lucian.paul-trifu@arm.com>
Link: https://lore.kernel.org/r/20230419-ffa_fixes_6-4-v2-3-d9108e43a176@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77c2a3097d upstream.
The bq24192 model relies on external charger-type detection and once
that is done the bq24190_charger code will update the input current.
In this case, when the initial power_supply_changed() call is made
from the interrupt handler, the input settings are 5V/0.5A which
on many devices is not enough power to charge (while the device is on).
On many devices the fuel-gauge relies in its external_power_changed
callback to timely signal userspace about charging <-> discharging
status changes. Add a power_supply_changed() call after updating
the input current. This allows the fuel-gauge driver to timely recheck
if the battery is charging after the new input current has been applied
and then it can immediately notify userspace about this.
Fixes: 18f8e6f695 ("power: supply: bq24190_charger: Get input_current_limit from our supplier")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad3d9c779b upstream.
The bq25892 model relies on external charger-type detection and once
that is done the bq25890_charger code will update the input current
and if pumpexpress is used also the input voltage.
In this case, when the initial power_supply_changed() call is made
from the interrupt handler, the input settings are 5V/0.5A which
on many devices is not enough power to charge (while the device is on).
On many devices the fuel-gauge relies in its external_power_changed
callback to timely signal userspace about charging <-> discharging
status changes. Add a power_supply_changed() call after updating
the input current or voltage. This allows the fuel-gauge driver
to timely recheck if the battery is charging after the new input
settings have been applied and then it can immediately notify
userspace about this.
Fixes: 48f45b094d ("power: supply: bq25890: Support higher charging voltages through Pump Express+ protocol")
Fixes: eab25b4f93 ("power: supply: bq25890: On the bq25892 set the IINLIM based on external charger detection")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 59a99cd462 upstream.
bq27xxx_external_power_changed() gets called when the charger is plugged
in or out. Rather then immediately scheduling an update wait 0.5 seconds
for things to stabilize, so that e.g. the (dis)charge current is stable
when bq27xxx_battery_update() runs.
Fixes: 740b755a3b ("bq27x00: Poll battery state")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 939a116142 upstream.
On gauges where the current register is signed, there is no charging
flag in the flags register. So only checking flags will not result
in power_supply_changed() getting called when e.g. a charger is plugged
in and the current sign changes from negative (discharging) to
positive (charging).
This causes userspace's notion of the status to lag until userspace
does a poll.
And when a power_supply_leds.c LED trigger is used to indicate charging
status with a LED, this LED will lag until the capacity percentage
changes, which may take many minutes (because the LED trigger only is
updated on power_supply_changed() calls).
Fix this by calling bq27xxx_battery_current_and_status() on gauges with
a signed current register and checking if the status has changed.
Fixes: 297a533b3e ("bq27x00: Cache battery registers")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff4c4a2a44 upstream.
Move the bq27xxx_battery_update() functions to below
the bq27xxx_battery_current_and_status() function.
This is just moving a block of text, no functional changes.
This is a preparation patch for making bq27xxx_battery_update() check
the status and have it call power_supply_changed() on status changes.
Fixes: 297a533b3e ("bq27x00: Cache battery registers")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 35092c5819 upstream.
Add a cache parameter to bq27xxx_battery_current_and_status() so that
it can optionally use cached flags instead of re-reading them itself.
This is a preparation patch for making bq27xxx_battery_update() check
the status and have it call power_supply_changed() on status changes.
Fixes: 297a533b3e ("bq27x00: Cache battery registers")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c00bc80462 upstream.
Before this patch bq27xxx_battery_teardown() was setting poll_interval = 0
to avoid bq27xxx_battery_update() requeuing the delayed_work item.
There are 2 problems with this:
1. If the driver is unbound through sysfs, rather then the module being
rmmod-ed, this changes poll_interval unexpectedly
2. This is racy, after it being set poll_interval could be changed
before bq27xxx_battery_update() checks it through
/sys/module/bq27xxx_battery/parameters/poll_interval
Fix this by added a removed attribute to struct bq27xxx_device_info and
using that instead of setting poll_interval to 0.
There also is another poll_interval related race on remove(), writing
/sys/module/bq27xxx_battery/parameters/poll_interval will requeue
the delayed_work item for all devices on the bq27xxx_battery_devices
list and the device being removed was only removed from that list
after cancelling the delayed_work item.
Fix this by moving the removal from the bq27xxx_battery_devices list
to before cancelling the delayed_work item.
Fixes: 8cfaaa8118 ("bq27x00_battery: Fix OOPS caused by unregistring bq27x00 driver")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 444ff00734 upstream.
devm_request_threaded_irq() requested IRQs are only free-ed after
the driver's remove function has ran. So the IRQ could trigger and
call bq27xxx_battery_update() after bq27xxx_battery_teardown() has
already run.
Switch to explicitly free-ing the IRQ in bq27xxx_battery_i2c_remove()
to fix this.
Fixes: 8807feb91b ("power: bq27xxx_battery: Add interrupt handling support")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c34c0aef1 upstream.
bq27xxx_battery_update() assumes / requires that it is only run once,
not multiple times at the same time. But there are 3 possible callers:
1. bq27xxx_battery_poll() delayed_work item handler
2. bq27xxx_battery_irq_handler_thread() I2C IRQ handler
3. bq27xxx_battery_setup()
And there is no protection against these racing with each other,
fix this race condition by making all callers take di->lock:
- Rename bq27xxx_battery_update() to bq27xxx_battery_update_unlocked()
- Add new bq27xxx_battery_update() which takes di->lock and then calls
bq27xxx_battery_update_unlocked()
- Make stale cache check code in bq27xxx_battery_get_property(), which
already takes di->lock directly to check the jiffies, call
bq27xxx_battery_update_unlocked() instead of messing with
the delayed_work item
- Make bq27xxx_battery_update_unlocked() mod the delayed-work item
so that the next poll is delayed to poll_interval milliseconds after
the last update independent of the source of the update
Fixes: 740b755a3b ("bq27x00: Poll battery state")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e448464399 upstream.
When a battery's status changes from charging to full then
the charging-blink-full-solid trigger tries to change
the LED from blinking to solid/on.
As is documented in include/linux/leds.h to deactivate blinking /
to make the LED solid a LED_OFF must be send:
"""
* Deactivate blinking again when the brightness is set to LED_OFF
* via the brightness_set() callback.
"""
led_set_brighness() calls with a brightness value other then 0 / LED_OFF
merely change the brightness of the LED in its on state while it is
blinking.
So power_supply_update_bat_leds() must first send a LED_OFF event
before the LED_FULL to disable blinking.
Fixes: 6501f728c5 ("power_supply: Add new LED trigger charging-blink-solid-full")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cb8b02fd63 upstream.
There are two ways that special characters (not allowed in some
other operating systems like Windows, but allowed in POSIX) have
been mapped in the past ("SFU" and "SFM" mappings) to allow them
to be stored in a range reserved for special chars. The default
for Linux has been to use "mapposix" (ie the SFM mapping) but
the conversion to the new mount API in the 5.11 kernel broke
the ability to override the default mapping of the reserved
characters (like '?' and '*' and '\') via "mapchars" mount option.
This patch fixes that - so can now mount with "mapchars"
mount option to override the default ("mapposix" ie SFM) mapping.
Reported-by: Tyler Spivey <tspivey8@gmail.com>
Fixes: 24e0a1eff9 ("cifs: switch to new mount api")
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 878ecb0897 upstream.
optlen is fetched without checking whether there is more than one byte to parse.
It can lead to out-of-bounds access.
Found by InfoTeCS on behalf of Linux Verification Center
(linuxtesting.org) with SVACE.
Fixes: c61a404325 ("[IPV6]: Find option offset by type.")
Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6007612459 upstream.
It was noticing that after a while when unloading/loading the driver and
sending traffic through the switch, it would stop working. It would stop
forwarding any traffic and the only way to get out of this was to do a
power cycle of the board. The root cause seems to be that the switch
core is initialized twice. Apparently initializing twice the switch core
disturbs the pointers in the queue systems in the HW, so after a while
it would stop sending the traffic.
Unfortunetly, it is not possible to use a reset of the switch here,
because the reset line is connected to multiple devices like MDIO,
SGPIO, FAN, etc. So then all the devices will get reseted when the
network driver will be loaded.
So the fix is to check if the core is initialized already and if that is
the case don't initialize it again.
Fixes: db8bcaad53 ("net: lan966x: add the basic lan966x driver")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230522120038.3749026-1-horatiu.vultur@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b34ffb0c6d upstream.
The LRU and LRU_PERCPU maps allocate a new element on update before locking the
target hash table bucket. Right after that the maps try to lock the bucket.
If this fails, then maps return -EBUSY to the caller without releasing the
allocated element. This makes the element untracked: it doesn't belong to
either of free lists, and it doesn't belong to the hash table, so can't be
re-used; this eventually leads to the permanent -ENOMEM on LRU map updates,
which is unexpected. Fix this by returning the element to the local free list
if bucket locking fails.
Fixes: 20b6cc34ea ("bpf: Avoid hashtab deadlock with map_locked")
Signed-off-by: Anton Protopopov <aspsk@isovalent.com>
Link: https://lore.kernel.org/r/20230522154558.2166815-1-aspsk@isovalent.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0613d8ca9a upstream.
A narrow load from a 64-bit context field results in a 64-bit load
followed potentially by a 64-bit right-shift and then a bitwise AND
operation to extract the relevant data.
In the case of a 32-bit access, an immediate mask of 0xffffffff is used
to construct a 64-bit BPP_AND operation which then sign-extends the mask
value and effectively acts as a glorified no-op. For example:
0: 61 10 00 00 00 00 00 00 r0 = *(u32 *)(r1 + 0)
results in the following code generation for a 64-bit field:
ldr x7, [x7] // 64-bit load
mov x10, #0xffffffffffffffff
and x7, x7, x10
Fix the mask generation so that narrow loads always perform a 32-bit AND
operation:
ldr x7, [x7] // 64-bit load
mov w10, #0xffffffff
and w7, w7, w10
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Krzesimir Nowak <krzesimir@kinvolk.io>
Cc: Andrey Ignatov <rdna@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Fixes: 31fd85816d ("bpf: permits narrower load from bpf program context fields")
Signed-off-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20230518102528.1341-1-will@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d226b1df36 upstream.
In the end of the test, there will be an error message induced by the
`ip netns del ns1` command in cleanup()
Tests passed: 201
Tests failed: 0
Cannot remove namespace file "/run/netns/ns1": No such file or directory
This can even be reproduced with just `./fib_tests.sh -h` as we're
calling cleanup() on exit.
Redirect the error message to /dev/null to mute it.
V2: Update commit message and fixes tag.
V3: resubmit due to missing netdev ML in V2
Fixes: b60417a9f2 ("selftest: fib_tests: Always cleanup before exit")
Signed-off-by: Po-Hsu Lin <po-hsu.lin@canonical.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c21f11d182 upstream.
In mutex_init() lockdep identifies a lock by defining a special static
key for each lock class. However if we wrap the macro in a function,
like in drmm_mutex_init(), we end up generating:
int drmm_mutex_init(struct drm_device *dev, struct mutex *lock)
{
static struct lock_class_key __key;
__mutex_init((lock), "lock", &__key);
....
}
The static __key here is what lockdep uses to identify the lock class,
however since this is just a normal function the key here will be
created once, where all callers then use the same key. In effect the
mutex->depmap.key will be the same pointer for different
drmm_mutex_init() callers. This then results in impossible lockdep
splats since lockdep thinks completely unrelated locks are the same lock
class.
To fix this turn drmm_mutex_init() into a macro such that it generates a
different "static struct lock_class_key __key" for each invocation,
which looks to be inline with what mutex_init() wants.
v2:
- Revamp the commit message with clearer explanation of the issue.
- Rather export __drmm_mutex_release() than static inline.
Reported-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reported-by: Sarah Walker <sarah.walker@imgtec.com>
Fixes: e13f13e039 ("drm: Add DRM-managed mutex_init()")
Cc: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Jocelyn Falempe <jfalempe@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230519090733.489019-1-matthew.auld@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a02fb71d7 upstream.
Commit 50749f2dd6 ("tcp/udp: Fix memleaks of sk and zerocopy skbs with
TX timestamp.") added a call to skb_orphan_frags_rx() to fix leaks with
zerocopy skbs. But it ended up adding a leak of its own. When
skb_orphan_frags_rx() fails, the function just returns, leaking the skb
it just cloned. Free it before returning.
This bug was discovered and resolved using Coverity Static Analysis
Security Testing (SAST) by Synopsys, Inc.
Fixes: 50749f2dd6 ("tcp/udp: Fix memleaks of sk and zerocopy skbs with TX timestamp.")
Signed-off-by: Pratyush Yadav <ptyadav@amazon.de>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20230522153020.32422-1-ptyadav@amazon.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 75e5fab7db upstream.
When we run syzkaller we get below Out of Bounds error.
"KASAN: slab-out-of-bounds Read in regcache_flat_read"
Below is the backtrace of the issue:
BUG: KASAN: slab-out-of-bounds in regcache_flat_read+0x10c/0x110
Read of size 4 at addr ffffff8088fbf714 by task syz-executor.4/14144
CPU: 6 PID: 14144 Comm: syz-executor.4 Tainted: G W
Hardware name: Qualcomm Technologies, Inc. sc7280 CRD platform (rev5+) (DT)
Call trace:
dump_backtrace+0x0/0x4ec
show_stack+0x34/0x50
dump_stack_lvl+0xdc/0x11c
print_address_description+0x30/0x2d8
kasan_report+0x178/0x1e4
__asan_report_load4_noabort+0x44/0x50
regcache_flat_read+0x10c/0x110
regcache_read+0xf8/0x5a0
_regmap_read+0x45c/0x86c
_regmap_update_bits+0x128/0x290
regmap_update_bits_base+0xc0/0x15c
snd_soc_component_update_bits+0xa8/0x22c
snd_soc_component_write_field+0x68/0xd4
tx_macro_put_dec_enum+0x1d0/0x268
snd_ctl_elem_write+0x288/0x474
By Error checking and checking valid values issue gets rectifies.
Signed-off-by: Ravulapati Vishnu Vardhan Rao <quic_visr@quicinc.com
Link: https://lore.kernel.org/r/20230511112532.16106-1-quic_visr@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1389062650 upstream.
Many of the older USB drivers in the Linux USB stack were written
based simply on a vendor's device specification. They use the
endpoint information in the spec and assume these endpoints will
always be present, with the properties listed, in any device matching
the given vendor and product IDs.
While that may have been true back then, with spoofing and fuzzing it
is not true any more. More and more we are finding that those old
drivers need to perform at least a minimum of checking before they try
to use any endpoint other than ep0.
To make this checking as simple as possible, we now add a couple of
utility routines to the USB core. usb_check_bulk_endpoints() and
usb_check_int_endpoints() take an interface pointer together with a
list of endpoint addresses (numbers and directions). They check that
the interface's current alternate setting includes endpoints with
those addresses and that each of these endpoints has the right type:
bulk or interrupt, respectively.
Although we already have usb_find_common_endpoints() and related
routines meant for a similar purpose, they are not well suited for
this kind of checking. Those routines find endpoints of various
kinds, but only one (either the first or the last) of each kind, and
they don't verify that the endpoints' addresses agree with what the
caller expects.
In theory the new routines could be more general: They could take a
particular altsetting as their argument instead of always using the
interface's current altsetting. In practice I think this won't matter
too much; multiple altsettings tend to be used for transferring media
(audio or visual) over isochronous endpoints, not bulk or interrupt.
Drivers for such devices will generally require more sophisticated
checking than these simplistic routines provide.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/dd2c8e8c-2c87-44ea-ba17-c64b97e201c9@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae9b15fbe6 upstream.
When the virtual interface's feature is updated, it synchronizes the
updated feature for its own lower interface.
This propagation logic should be worked as the iteration, not recursively.
But it works recursively due to the netdev notification unexpectedly.
This problem occurs when it disables LRO only for the team and bonding
interface type.
team0
|
+------+------+-----+-----+
| | | | |
team1 team2 team3 ... team200
If team0's LRO feature is updated, it generates the NETDEV_FEAT_CHANGE
event to its own lower interfaces(team1 ~ team200).
It is worked by netdev_sync_lower_features().
So, the NETDEV_FEAT_CHANGE notification logic of each lower interface
work iteratively.
But generated NETDEV_FEAT_CHANGE event is also sent to the upper
interface too.
upper interface(team0) generates the NETDEV_FEAT_CHANGE event for its own
lower interfaces again.
lower and upper interfaces receive this event and generate this
event again and again.
So, the stack overflow occurs.
But it is not the infinite loop issue.
Because the netdev_sync_lower_features() updates features before
generating the NETDEV_FEAT_CHANGE event.
Already synchronized lower interfaces skip notification logic.
So, it is just the problem that iteration logic is changed to the
recursive unexpectedly due to the notification mechanism.
Reproducer:
ip link add team0 type team
ethtool -K team0 lro on
for i in {1..200}
do
ip link add team$i master team0 type team
ethtool -K team$i lro on
done
ethtool -K team0 lro off
In order to fix it, the notifier_ctx member of bonding/team is introduced.
Reported-by: syzbot+60748c96cf5c6df8e581@syzkaller.appspotmail.com
Fixes: fd867d51f8 ("net/core: generic support for disabling netdev features down stack")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230517143010.3596250-1-ap420073@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed9de4ed39 upstream.
The syzbot fuzzer detected a problem in the udlfb driver, caused by an
endpoint not having the expected type:
usb 1-1: Read EDID byte 0 failed: -71
usb 1-1: Unable to get valid EDID from device/display
------------[ cut here ]------------
usb 1-1: BOGUS urb xfer, pipe 3 != type 1
WARNING: CPU: 0 PID: 9 at drivers/usb/core/urb.c:504 usb_submit_urb+0xed6/0x1880
drivers/usb/core/urb.c:504
Modules linked in:
CPU: 0 PID: 9 Comm: kworker/0:1 Not tainted
6.4.0-rc1-syzkaller-00016-ga4422ff22142 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google
04/28/2023
Workqueue: usb_hub_wq hub_event
RIP: 0010:usb_submit_urb+0xed6/0x1880 drivers/usb/core/urb.c:504
...
Call Trace:
<TASK>
dlfb_submit_urb+0x92/0x180 drivers/video/fbdev/udlfb.c:1980
dlfb_set_video_mode+0x21f0/0x2950 drivers/video/fbdev/udlfb.c:315
dlfb_ops_set_par+0x2a7/0x8d0 drivers/video/fbdev/udlfb.c:1111
dlfb_usb_probe+0x149a/0x2710 drivers/video/fbdev/udlfb.c:1743
The current approach for this issue failed to catch the problem
because it only checks for the existence of a bulk-OUT endpoint; it
doesn't check whether this endpoint is the one that the driver will
actually use.
We can fix the problem by instead checking that the endpoint used by
the driver does exist and is bulk-OUT.
Reported-and-tested-by: syzbot+0e22d63dcebb802b9bc8@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Pavel Skripkin <paskripkin@gmail.com>
Fixes: aaf7dbe073 ("video: fbdev: udlfb: properly check endpoint type")
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d6a0e4197 upstream.
Since we may hold gic_lock in hardirq context, use raw spinlock
makes more sense given that it is for low-level interrupt handling
routine and the critical section is small.
Fixes BUG:
[ 0.426106] =============================
[ 0.426257] [ BUG: Invalid wait context ]
[ 0.426422] 6.3.0-rc7-next-20230421-dirty #54 Not tainted
[ 0.426638] -----------------------------
[ 0.426766] swapper/0/1 is trying to lock:
[ 0.426954] ffffffff8104e7b8 (gic_lock){....}-{3:3}, at: gic_set_type+0x30/08
Fixes: 95150ae8b3 ("irqchip: mips-gic: Implement irq_set_type callback")
Cc: stable@vger.kernel.org
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230424103156.66753-3-jiaxun.yang@flygoat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c6c9c0495 upstream.
When a GIC local interrupt is not routable, it's vl_map will be used
to control some internal states for core (providing IPTI, IPPCI, IPFDC
input signal for core). Overriding it will interfere core's intetrupt
controller.
Do not touch vl_map if a local interrupt is not routable, we are not
going to remap it.
Before dd098a0e03 (" irqchip/mips-gic: Get rid of the reliance on
irq_cpu_online()"), if a local interrupt is not routable, then it won't
be requested from GIC Local domain, and thus gic_all_vpes_irq_cpu_online
won't be called for that particular interrupt.
Fixes: dd098a0e03 (" irqchip/mips-gic: Get rid of the reliance on irq_cpu_online()")
Cc: stable@vger.kernel.org
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230424103156.66753-2-jiaxun.yang@flygoat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit edc0a2b595 upstream.
Traditionally, all CPUs in a system have identical numbers of SMT
siblings. That changes with hybrid processors where some logical CPUs
have a sibling and others have none.
Today, the CPU boot code sets the global variable smp_num_siblings when
every CPU thread is brought up. The last thread to boot will overwrite
it with the number of siblings of *that* thread. That last thread to
boot will "win". If the thread is a Pcore, smp_num_siblings == 2. If it
is an Ecore, smp_num_siblings == 1.
smp_num_siblings describes if the *system* supports SMT. It should
specify the maximum number of SMT threads among all cores.
Ensure that smp_num_siblings represents the system-wide maximum number
of siblings by always increasing its value. Never allow it to decrease.
On MeteorLake-P platform, this fixes a problem that the Ecore CPUs are
not updated in any cpu sibling map because the system is treated as an
UP system when probing Ecore CPUs.
Below shows part of the CPU topology information before and after the
fix, for both Pcore and Ecore CPU (cpu0 is Pcore, cpu 12 is Ecore).
...
-/sys/devices/system/cpu/cpu0/topology/package_cpus:000fff
-/sys/devices/system/cpu/cpu0/topology/package_cpus_list:0-11
+/sys/devices/system/cpu/cpu0/topology/package_cpus:3fffff
+/sys/devices/system/cpu/cpu0/topology/package_cpus_list:0-21
...
-/sys/devices/system/cpu/cpu12/topology/package_cpus:001000
-/sys/devices/system/cpu/cpu12/topology/package_cpus_list:12
+/sys/devices/system/cpu/cpu12/topology/package_cpus:3fffff
+/sys/devices/system/cpu/cpu12/topology/package_cpus_list:0-21
Notice that the "before" 'package_cpus_list' has only one CPU. This
means that userspace tools like lscpu will see a little laptop like
an 11-socket system:
-Core(s) per socket: 1
-Socket(s): 11
+Core(s) per socket: 16
+Socket(s): 1
This is also expected to make the scheduler do rather wonky things
too.
[ dhansen: remove CPUID detail from changelog, add end user effects ]
CC: stable@kernel.org
Fixes: bbb65d2d36 ("x86: use cpuid vector 0xb when available for detecting cpu topology")
Fixes: 95f3d39ccf ("x86/cpu/topology: Provide detect_extended_topology_early()")
Suggested-by: Len Brown <len.brown@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/all/20230323015640.27906-1-rui.zhang%40intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d1d8875c8c upstream.
[ cmllamas: clean forward port from commit 015ac18be7de ("binder: fix
UAF of alloc->vma in race with munmap()") in 5.10 stable. It is needed
in mainline after the revert of commit a43cfc87ca ("android: binder:
stop saving a pointer to the VMA") as pointed out by Liam. The commit
log and tags have been tweaked to reflect this. ]
In commit 720c241924 ("ANDROID: binder: change down_write to
down_read") binder assumed the mmap read lock is sufficient to protect
alloc->vma inside binder_update_page_range(). This used to be accurate
until commit dd2283f260 ("mm: mmap: zap pages with read mmap_sem in
munmap"), which now downgrades the mmap_lock after detaching the vma
from the rbtree in munmap(). Then it proceeds to teardown and free the
vma with only the read lock held.
This means that accesses to alloc->vma in binder_update_page_range() now
will race with vm_area_free() in munmap() and can cause a UAF as shown
in the following KASAN trace:
==================================================================
BUG: KASAN: use-after-free in vm_insert_page+0x7c/0x1f0
Read of size 8 at addr ffff16204ad00600 by task server/558
CPU: 3 PID: 558 Comm: server Not tainted 5.10.150-00001-gdc8dcf942daa #1
Hardware name: linux,dummy-virt (DT)
Call trace:
dump_backtrace+0x0/0x2a0
show_stack+0x18/0x2c
dump_stack+0xf8/0x164
print_address_description.constprop.0+0x9c/0x538
kasan_report+0x120/0x200
__asan_load8+0xa0/0xc4
vm_insert_page+0x7c/0x1f0
binder_update_page_range+0x278/0x50c
binder_alloc_new_buf+0x3f0/0xba0
binder_transaction+0x64c/0x3040
binder_thread_write+0x924/0x2020
binder_ioctl+0x1610/0x2e5c
__arm64_sys_ioctl+0xd4/0x120
el0_svc_common.constprop.0+0xac/0x270
do_el0_svc+0x38/0xa0
el0_svc+0x1c/0x2c
el0_sync_handler+0xe8/0x114
el0_sync+0x180/0x1c0
Allocated by task 559:
kasan_save_stack+0x38/0x6c
__kasan_kmalloc.constprop.0+0xe4/0xf0
kasan_slab_alloc+0x18/0x2c
kmem_cache_alloc+0x1b0/0x2d0
vm_area_alloc+0x28/0x94
mmap_region+0x378/0x920
do_mmap+0x3f0/0x600
vm_mmap_pgoff+0x150/0x17c
ksys_mmap_pgoff+0x284/0x2dc
__arm64_sys_mmap+0x84/0xa4
el0_svc_common.constprop.0+0xac/0x270
do_el0_svc+0x38/0xa0
el0_svc+0x1c/0x2c
el0_sync_handler+0xe8/0x114
el0_sync+0x180/0x1c0
Freed by task 560:
kasan_save_stack+0x38/0x6c
kasan_set_track+0x28/0x40
kasan_set_free_info+0x24/0x4c
__kasan_slab_free+0x100/0x164
kasan_slab_free+0x14/0x20
kmem_cache_free+0xc4/0x34c
vm_area_free+0x1c/0x2c
remove_vma+0x7c/0x94
__do_munmap+0x358/0x710
__vm_munmap+0xbc/0x130
__arm64_sys_munmap+0x4c/0x64
el0_svc_common.constprop.0+0xac/0x270
do_el0_svc+0x38/0xa0
el0_svc+0x1c/0x2c
el0_sync_handler+0xe8/0x114
el0_sync+0x180/0x1c0
[...]
==================================================================
To prevent the race above, revert back to taking the mmap write lock
inside binder_update_page_range(). One might expect an increase of mmap
lock contention. However, binder already serializes these calls via top
level alloc->mutex. Also, there was no performance impact shown when
running the binder benchmark tests.
Fixes: c0fd210178 ("Revert "android: binder: stop saving a pointer to the VMA"")
Fixes: dd2283f260 ("mm: mmap: zap pages with read mmap_sem in munmap")
Reported-by: Jann Horn <jannh@google.com>
Closes: https://lore.kernel.org/all/20230518144052.xkj6vmddccq4v66b@revolver
Cc: <stable@vger.kernel.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Yang Shi <yang.shi@linux.alibaba.com>
Cc: Liam Howlett <liam.howlett@oracle.com>
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Acked-by: Todd Kjos <tkjos@google.com>
Link: https://lore.kernel.org/r/20230519195950.1775656-1-cmllamas@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bdc1c5fac9 upstream.
In binder_transaction_buffer_release() the 'failed_at' offset indicates
the number of objects to clean up. However, this function was changed by
commit 44d8047f1d ("binder: use standard functions to allocate fds"),
to release all the objects in the buffer when 'failed_at' is zero.
This introduced an issue when a transaction buffer is released without
any objects having been processed so far. In this case, 'failed_at' is
indeed zero yet it is misinterpreted as releasing the entire buffer.
This leads to use-after-free errors where nodes are incorrectly freed
and subsequently accessed. Such is the case in the following KASAN
report:
==================================================================
BUG: KASAN: slab-use-after-free in binder_thread_read+0xc40/0x1f30
Read of size 8 at addr ffff4faf037cfc58 by task poc/474
CPU: 6 PID: 474 Comm: poc Not tainted 6.3.0-12570-g7df047b3f0aa #5
Hardware name: linux,dummy-virt (DT)
Call trace:
dump_backtrace+0x94/0xec
show_stack+0x18/0x24
dump_stack_lvl+0x48/0x60
print_report+0xf8/0x5b8
kasan_report+0xb8/0xfc
__asan_load8+0x9c/0xb8
binder_thread_read+0xc40/0x1f30
binder_ioctl+0xd9c/0x1768
__arm64_sys_ioctl+0xd4/0x118
invoke_syscall+0x60/0x188
[...]
Allocated by task 474:
kasan_save_stack+0x3c/0x64
kasan_set_track+0x2c/0x40
kasan_save_alloc_info+0x24/0x34
__kasan_kmalloc+0xb8/0xbc
kmalloc_trace+0x48/0x5c
binder_new_node+0x3c/0x3a4
binder_transaction+0x2b58/0x36f0
binder_thread_write+0x8e0/0x1b78
binder_ioctl+0x14a0/0x1768
__arm64_sys_ioctl+0xd4/0x118
invoke_syscall+0x60/0x188
[...]
Freed by task 475:
kasan_save_stack+0x3c/0x64
kasan_set_track+0x2c/0x40
kasan_save_free_info+0x38/0x5c
__kasan_slab_free+0xe8/0x154
__kmem_cache_free+0x128/0x2bc
kfree+0x58/0x70
binder_dec_node_tmpref+0x178/0x1fc
binder_transaction_buffer_release+0x430/0x628
binder_transaction+0x1954/0x36f0
binder_thread_write+0x8e0/0x1b78
binder_ioctl+0x14a0/0x1768
__arm64_sys_ioctl+0xd4/0x118
invoke_syscall+0x60/0x188
[...]
==================================================================
In order to avoid these issues, let's always calculate the intended
'failed_at' offset beforehand. This is renamed and wrapped in a helper
function to make it clear and convenient.
Fixes: 32e9f56a96 ("binder: don't detect sender/target during buffer cleanup")
Reported-by: Zi Fan Tan <zifantan@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Acked-by: Todd Kjos <tkjos@google.com>
Link: https://lore.kernel.org/r/20230505203020.4101154-1-cmllamas@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0fa53349c3 upstream.
Bring back the original lockless design in binder_alloc to determine
whether the buffer setup has been completed by the ->mmap() handler.
However, this time use smp_load_acquire() and smp_store_release() to
wrap all the ordering in a single macro call.
Also, add comments to make it evident that binder uses alloc->vma to
determine when the binder_alloc has been fully initialized. In these
scenarios acquiring the mmap_lock is not required.
Fixes: a43cfc87ca ("android: binder: stop saving a pointer to the VMA")
Cc: Liam Howlett <liam.howlett@oracle.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Link: https://lore.kernel.org/r/20230502201220.1756319-3-cmllamas@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40baba5693 upstream.
Printing the other clock types should not be conditioned on being able
to print OD_SCLK. Some GPUs currently have limited capability of only
printing a subset of these.
Since this condition was introduced in v5.18-rc1, reading from
`pp_od_clk_voltage` has been returning empty on the Asus ROG Strix G15
(2021).
Fixes: 79c65f3fcb ("drm/amd/pm: do not expose power implementation details to amdgpu_pm.c")
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Jonatas Esteves <jntesteves@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 482e6ad9ad upstream.
At drm suspend sequence, MST dc_sink is removed. When commit cached
MST stream back in drm resume sequence, the MST stream payload is not
properly created and added into the payload table. After resume, topology
change is reprobed by removing existing streams first. That leads to
no payload is found in the existing payload table as below error
"[drm] ERROR No payload for [MST PORT:] found in mst state"
1. In encoder .atomic_check routine, remove check existance of dc_sink
2. Bypass MST by checking existence of MST root port. dc_link_type cannot
differentiate MST port before topology is rediscovered.
Reviewed-by: Wayne Lin <wayne.lin@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 50a1726b14 upstream.
In cdns3-gadget.c, 'cdns,on-chip-buff-size' was read using
device_property_read_u16(). It resulted in 0 if a 32bit value was used
in dts. This commit fixes the dt binding doc to declare it as u16.
Cc: stable@vger.kernel.org
Fixes: 68989fe1c3 ("dt-bindings: usb: Convert cdns-usb3.txt to YAML schema")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46930b7cc7 upstream.
commit <8af870aa5b847> ("block: enable bio caching use for passthru IO")
introduced bio-cache for passthru IO. In case when nr_vecs are greater
than BIO_INLINE_VECS, bio and bvecs are allocated from mempool (instead
of percpu cache) and REQ_ALLOC_CACHE is cleared. This causes the side
effect of not freeing bio/bvecs into mempool on completion.
This patch lets the passthru IO fallback to allocation using bio_kmalloc
when nr_vecs are greater than BIO_INLINE_VECS. The corresponding bio
is freed during call to blk_mq_map_bio_put during completion.
Cc: stable@vger.kernel.org # 6.1
fixes <8af870aa5b847> ("block: enable bio caching use for passthru IO")
Signed-off-by: Anuj Gupta <anuj20.g@samsung.com>
Signed-off-by: Kanchan Joshi <joshi.k@samsung.com>
Link: https://lore.kernel.org/r/20230523111709.145676-1-anuj20.g@samsung.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f7fdb0f25 upstream.
Prior to the commit "763bd29fd3d1 ("thermal: int340x_thermal: Use
sysfs_emit_at() instead of scnprintf()", there was a new line after each
UUID string.
With the newline removed, existing user space like "thermald" fails to
compare each supported UUID as it is using getline() to read UUID and
apply correct thermal table.
To avoid breaking existing user space, add newline after each UUID string.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Fixes: 763bd29fd3 ("thermal: int340x_thermal: Use sysfs_emit_at() instead of scnprintf()")
Cc: 6.3+ <stable@vger.kernel.org> # 6.3+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 597441b343 upstream.
Our CI system caught a lockdep splat:
======================================================
WARNING: possible circular locking dependency detected
6.3.0-rc7+ #1167 Not tainted
------------------------------------------------------
kswapd0/46 is trying to acquire lock:
ffff8c6543abd650 (sb_internal#2){++++}-{0:0}, at: btrfs_commit_inode_delayed_inode+0x5f/0x120
but task is already holding lock:
ffffffffabe61b40 (fs_reclaim){+.+.}-{0:0}, at: balance_pgdat+0x4aa/0x7a0
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (fs_reclaim){+.+.}-{0:0}:
fs_reclaim_acquire+0xa5/0xe0
kmem_cache_alloc+0x31/0x2c0
alloc_extent_state+0x1d/0xd0
__clear_extent_bit+0x2e0/0x4f0
try_release_extent_mapping+0x216/0x280
btrfs_release_folio+0x2e/0x90
invalidate_inode_pages2_range+0x397/0x470
btrfs_cleanup_dirty_bgs+0x9e/0x210
btrfs_cleanup_one_transaction+0x22/0x760
btrfs_commit_transaction+0x3b7/0x13a0
create_subvol+0x59b/0x970
btrfs_mksubvol+0x435/0x4f0
__btrfs_ioctl_snap_create+0x11e/0x1b0
btrfs_ioctl_snap_create_v2+0xbf/0x140
btrfs_ioctl+0xa45/0x28f0
__x64_sys_ioctl+0x88/0xc0
do_syscall_64+0x38/0x90
entry_SYSCALL_64_after_hwframe+0x72/0xdc
-> #0 (sb_internal#2){++++}-{0:0}:
__lock_acquire+0x1435/0x21a0
lock_acquire+0xc2/0x2b0
start_transaction+0x401/0x730
btrfs_commit_inode_delayed_inode+0x5f/0x120
btrfs_evict_inode+0x292/0x3d0
evict+0xcc/0x1d0
inode_lru_isolate+0x14d/0x1e0
__list_lru_walk_one+0xbe/0x1c0
list_lru_walk_one+0x58/0x80
prune_icache_sb+0x39/0x60
super_cache_scan+0x161/0x1f0
do_shrink_slab+0x163/0x340
shrink_slab+0x1d3/0x290
shrink_node+0x300/0x720
balance_pgdat+0x35c/0x7a0
kswapd+0x205/0x410
kthread+0xf0/0x120
ret_from_fork+0x29/0x50
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(fs_reclaim);
lock(sb_internal#2);
lock(fs_reclaim);
lock(sb_internal#2);
*** DEADLOCK ***
3 locks held by kswapd0/46:
#0: ffffffffabe61b40 (fs_reclaim){+.+.}-{0:0}, at: balance_pgdat+0x4aa/0x7a0
#1: ffffffffabe50270 (shrinker_rwsem){++++}-{3:3}, at: shrink_slab+0x113/0x290
#2: ffff8c6543abd0e0 (&type->s_umount_key#44){++++}-{3:3}, at: super_cache_scan+0x38/0x1f0
stack backtrace:
CPU: 0 PID: 46 Comm: kswapd0 Not tainted 6.3.0-rc7+ #1167
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.13.0-2.fc32 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x58/0x90
check_noncircular+0xd6/0x100
? save_trace+0x3f/0x310
? add_lock_to_list+0x97/0x120
__lock_acquire+0x1435/0x21a0
lock_acquire+0xc2/0x2b0
? btrfs_commit_inode_delayed_inode+0x5f/0x120
start_transaction+0x401/0x730
? btrfs_commit_inode_delayed_inode+0x5f/0x120
btrfs_commit_inode_delayed_inode+0x5f/0x120
btrfs_evict_inode+0x292/0x3d0
? lock_release+0x134/0x270
? __pfx_wake_bit_function+0x10/0x10
evict+0xcc/0x1d0
inode_lru_isolate+0x14d/0x1e0
__list_lru_walk_one+0xbe/0x1c0
? __pfx_inode_lru_isolate+0x10/0x10
? __pfx_inode_lru_isolate+0x10/0x10
list_lru_walk_one+0x58/0x80
prune_icache_sb+0x39/0x60
super_cache_scan+0x161/0x1f0
do_shrink_slab+0x163/0x340
shrink_slab+0x1d3/0x290
shrink_node+0x300/0x720
balance_pgdat+0x35c/0x7a0
kswapd+0x205/0x410
? __pfx_autoremove_wake_function+0x10/0x10
? __pfx_kswapd+0x10/0x10
kthread+0xf0/0x120
? __pfx_kthread+0x10/0x10
ret_from_fork+0x29/0x50
</TASK>
This happens because when we abort the transaction in the transaction
commit path we call invalidate_inode_pages2_range on our block group
cache inodes (if we have space cache v1) and any delalloc inodes we may
have. The plain invalidate_inode_pages2_range() call passes through
GFP_KERNEL, which makes sense in most cases, but not here. Wrap these
two invalidate callees with memalloc_nofs_save/memalloc_nofs_restore to
make sure we don't end up with the fs reclaim dependency under the
transaction dependency.
CC: stable@vger.kernel.org # 4.14+
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0a1bb16e0f upstream.
This driver's debugfs files have had a read operation since commit
2a9e27408e ("gpio: mockup: rework debugfs interface"), but were
still being created with write-only mode bits. Update them to
indicate that the files can also be read.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Fixes: 2a9e27408e ("gpio: mockup: rework debugfs interface")
Cc: stable@kernel.org # v5.1+
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eb0764b822 upstream.
Derick noticed, when testing hot plug, that hot-add behaves nominally
after a removal. However, if the hot-add is done without a prior
removal, CXL.mem accesses fail. It turns out that the original
implementation of the port driver and region programming wrongly assumed
that platform-firmware always enables the host-bridge HDM decoder
capability. Add support turning on switch-level HDM decoders in the case
where platform-firmware has not.
The implementation is careful to only arrange for the enable to be
undone if the current instance of the driver was the one that did the
enable. This is to interoperate with platform-firmware that may expect
CXL.mem to remain active after the driver is shutdown. This comes at the
cost of potentially not shutting down the enable on kexec flows, but it
is mitigated by the fact that the related HDM decoders still need to be
enabled on an individual basis.
Cc: <stable@vger.kernel.org>
Reported-by: Derick Marks <derick.w.marks@intel.com>
Fixes: 54cdbf845c ("cxl/port: Add a driver for 'struct cxl_port' objects")
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Link: https://lore.kernel.org/r/168437998331.403037.15719879757678389217.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9419092fb2 upstream.
On a filesystem with a non-zero stripe unit and a large sequential
write, delayed allocation will set a minimum allocation length of
the stripe unit. If allocation fails because there are no extents
long enough for an aligned minlen allocation, it is supposed to
fall back to unaligned allocation which allows single block extents
to be allocated.
When the allocator code was rewritting in the 6.3 cycle, this
fallback was broken - the old code used args->fsbno as the both the
allocation target and the allocation result, the new code passes the
target as a separate parameter. The conversion didn't handle the
aligned->unaligned fallback path correctly - it reset args->fsbno to
the target fsbno on failure which broke allocation failure detection
in the high level code and so it never fell back to unaligned
allocations.
This resulted in a loop in writeback trying to allocate an aligned
block, getting a false positive success, trying to insert the result
in the BMBT. This did nothing because the extent already was in the
BMBT (merge results in an unchanged extent) and so it returned the
prior extent to the conversion code as the current iomap.
Because the iomap returned didn't cover the offset we tried to map,
xfs_convert_blocks() then retries the allocation, which fails in the
same way and now we have a livelock.
Reported-and-tested-by: Brian Foster <bfoster@redhat.com>
Fixes: 8584332709 ("xfs: factor xfs_bmap_btalloc()")
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2028315cf5 upstream.
In case a machine can't power-off itself on system shutdown,
allow the user to reboot it by pressing the RETURN key.
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61e150fb31 upstream.
Since at least kernel 6.1, flush_dcache_page() is called with IRQs
disabled, e.g. from aio_complete().
But the current implementation for flush_dcache_page() on parisc
unintentionally re-enables IRQs, which may lead to deadlocks.
Fix it by using xa_lock_irqsave() and xa_unlock_irqrestore()
for the flush_dcache_mmap_*lock() macros instead.
Cc: linux-parisc@vger.kernel.org
Cc: stable@kernel.org # 5.18+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6405f0829 upstream.
When patching the kernel code some alternatives depend on SMP vs. !SMP.
Use the value of num_present_cpus() instead of num_online_cpus() to
decide, otherwise we may run into issues if and additional CPU is
enabled after having loaded a module while only one CPU was enabled.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org> # v6.1+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 034f4a7877 upstream.
gcc-13 may generate calls for __bswap{si,di}2. This breaks the kernel
build when optimization for size is selected. Add __bswap{si,di}2
helpers to fix that.
Cc: stable@vger.kernel.org
Fixes: 19c5699f9a ("xtensa: don't link with libgcc")
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c2cc74fb3 upstream.
Fetch function descriptor pointed to by the signal handler pointer from
userspace on signal delivery and function pointer pointed to by the
sa_restorer on return from the signal handler.
Cc: stable@vger.kernel.org
Fixes: e3ddb8bbe0 ("xtensa: add FDPIC and static PIE support for noMMU")
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3632679d9e upstream.
With a raw socket bound to IPPROTO_RAW (ie with hdrincl enabled), the
protocol field of the flow structure, build by raw_sendmsg() /
rawv6_sendmsg()), is set to IPPROTO_RAW. This breaks the ipsec policy
lookup when some policies are defined with a protocol in the selector.
For ipv6, the sin6_port field from 'struct sockaddr_in6' could be used to
specify the protocol. Just accept all values for IPPROTO_RAW socket.
For ipv4, the sin_port field of 'struct sockaddr_in' could not be used
without breaking backward compatibility (the value of this field was never
checked). Let's add a new kind of control message, so that the userland
could specify which protocol is used.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
CC: stable@vger.kernel.org
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Link: https://lore.kernel.org/r/20230522120820.1319391-1-nicolas.dichtel@6wind.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b845b574f8 upstream.
On 68030/020, an instruction such as, moveml %a2-%a3/%a5,%sp@- may cause
a stack page fault during instruction execution (i.e. not at an
instruction boundary) and produce a format 0xB exception frame.
In this situation, the value of USP will be unreliable. If a signal is
to be delivered following the exception, this USP value is used to
calculate the location for a signal frame. This can result in a
corrupted user stack.
The corruption was detected in dash (actually in glibc) where it showed
up as an intermittent "stack smashing detected" message and crash
following signal delivery for SIGCHLD.
It was hard to reproduce that failure because delivery of the signal
raced with the page fault and because the kernel places an unpredictable
gap of up to 7 bytes between the USP and the signal frame.
A format 0xB exception frame can be produced by a bus error or an
address error. The 68030 Users Manual says that address errors occur
immediately upon detection during instruction prefetch. The instruction
pipeline allows prefetch to overlap with other instructions, which means
an address error can arise during the execution of a different
instruction. So it seems likely that this patch may help in the address
error case also.
Reported-and-tested-by: Stan Johnson <userm57@yahoo.com>
Link: https://lore.kernel.org/all/CAMuHMdW3yD22_ApemzW_6me3adq6A458u1_F0v-1EYwK_62jPA@mail.gmail.com/
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Cc: stable@vger.kernel.org
Co-developed-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/9e66262a754fcba50208aa424188896cc52a1dd1.1683365892.git.fthain@linux-m68k.org
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e01c7f704 upstream.
Currently in cdc_ncm_check_tx_max(), if dwNtbOutMaxSize is lower than
the calculated "min" value, but greater than zero, the logic sets
tx_max to dwNtbOutMaxSize. This is then used to allocate a new SKB in
cdc_ncm_fill_tx_frame() where all the data is handled.
For small values of dwNtbOutMaxSize the memory allocated during
alloc_skb(dwNtbOutMaxSize, GFP_ATOMIC) will have the same size, due to
how size is aligned at alloc time:
size = SKB_DATA_ALIGN(size);
size += SKB_DATA_ALIGN(sizeof(struct skb_shared_info));
Thus we hit the same bug that we tried to squash with
commit 2be6d4d16a ("net: cdc_ncm: Allow for dwNtbOutMaxSize to be unset or zero")
Low values of dwNtbOutMaxSize do not cause an issue presently because at
alloc_skb() time more memory (512b) is allocated than required for the
SKB headers alone (320b), leaving some space (512b - 320b = 192b)
for CDC data (172b).
However, if more elements (for example 3 x u64 = [24b]) were added to
one of the SKB header structs, say 'struct skb_shared_info',
increasing its original size (320b [320b aligned]) to something larger
(344b [384b aligned]), then suddenly the CDC data (172b) no longer
fits in the spare SKB data area (512b - 384b = 128b).
Consequently the SKB bounds checking semantics fails and panics:
skbuff: skb_over_panic: text:ffffffff831f755b len:184 put:172 head:ffff88811f1c6c00 data:ffff88811f1c6c00 tail:0xb8 end:0x80 dev:<NULL>
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:113!
invalid opcode: 0000 [#1] PREEMPT SMP KASAN
CPU: 0 PID: 57 Comm: kworker/0:2 Not tainted 5.15.106-syzkaller-00249-g19c0ed55a470 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/14/2023
Workqueue: mld mld_ifc_work
RIP: 0010:skb_panic net/core/skbuff.c:113 [inline]
RIP: 0010:skb_over_panic+0x14c/0x150 net/core/skbuff.c:118
[snip]
Call Trace:
<TASK>
skb_put+0x151/0x210 net/core/skbuff.c:2047
skb_put_zero include/linux/skbuff.h:2422 [inline]
cdc_ncm_ndp16 drivers/net/usb/cdc_ncm.c:1131 [inline]
cdc_ncm_fill_tx_frame+0x11ab/0x3da0 drivers/net/usb/cdc_ncm.c:1308
cdc_ncm_tx_fixup+0xa3/0x100
Deal with too low values of dwNtbOutMaxSize, clamp it in the range
[USB_CDC_NCM_NTB_MIN_OUT_SIZE, CDC_NCM_NTB_MAX_SIZE_TX]. We ensure
enough data space is allocated to handle CDC data by making sure
dwNtbOutMaxSize is not smaller than USB_CDC_NCM_NTB_MIN_OUT_SIZE.
Fixes: 289507d336 ("net: cdc_ncm: use sysfs for rx/tx aggregation tuning")
Cc: stable@vger.kernel.org
Reported-by: syzbot+9f575a1f15fc0c01ed69@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=b982f1059506db48409d
Link: https://lore.kernel.org/all/20211202143437.1411410-1-lee.jones@linaro.org/
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230517133808.1873695-2-tudor.ambarus@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b271370e9 upstream.
The rt5682 driver switches its regmap to cache-only when the
device suspends and back to regular mode on resume. When the
jack detect interrupt fires rt5682_irq() schedules the jack
detect work. This can result in invalid reads from the regmap
in cache-only mode if the work runs before the device has
resumed:
[ 56.245502] rt5682 9-001a: ASoC: error at soc_component_read_no_lock on rt5682.9-001a for register: [0x000000f0] -16
Disable the jack detection interrupt during suspend and
re-enable it on resume. The driver already schedules the
jack detection work on resume, so any state change during
suspend is still handled.
This is essentially the same as commit f7d00a9be1 ("SoC:
rt5682s: Disable jack detection interrupt during suspend")
for the rt5682s.
Cc: stable@kernel.org
Signed-off-by: Matthias Kaehlcke <mka@chromium.org
Reviewed-by: Douglas Anderson <dianders@chromium.org
Reviewed-by: Stephen Boyd <swboyd@chromium.org
Link: https://lore.kernel.org/r/20230516164629.1.Ibf79e94b3442eecc0054d2b478779cc512d967fc@changeid
Signed-off-by: Mark Brown <broonie@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 029a443b9b upstream.
bq25890_charger_external_power_changed() dereferences bq->charger,
which gets sets in bq25890_power_supply_init() like this:
bq->charger = devm_power_supply_register(bq->dev, &bq->desc, &psy_cfg);
As soon as devm_power_supply_register() has called device_add()
the external_power_changed callback can get called. So there is a window
where bq25890_charger_external_power_changed() may get called while
bq->charger has not been set yet leading to a NULL pointer dereference.
This race hits during boot sometimes on a Lenovo Yoga Book 1 yb1-x90f
when the cht_wcove_pwrsrc (extcon) power_supply is done with detecting
the connected charger-type which happens to exactly hit the small window:
BUG: kernel NULL pointer dereference, address: 0000000000000018
<snip>
RIP: 0010:__power_supply_is_supplied_by+0xb/0xb0
<snip>
Call Trace:
<TASK>
__power_supply_get_supplier_property+0x19/0x50
class_for_each_device+0xb1/0xe0
power_supply_get_property_from_supplier+0x2e/0x50
bq25890_charger_external_power_changed+0x38/0x1b0 [bq25890_charger]
__power_supply_changed_work+0x30/0x40
class_for_each_device+0xb1/0xe0
power_supply_changed_work+0x5f/0xe0
<snip>
Fixing this is easy. The external_power_changed callback gets passed
the power_supply which will eventually get stored in bq->charger,
so bq25890_charger_external_power_changed() can simply directly use
the passed in psy argument which is always valid.
Fixes: eab25b4f93 ("power: supply: bq25890: On the bq25892 set the IINLIM based on external charger detection")
Cc: stable@vger.kernel.org
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f8319774d6 upstream.
fuel_gauge_external_power_changed() dereferences info->bat,
which gets sets in axp288_fuel_gauge_probe() like this:
info->bat = devm_power_supply_register(dev, &fuel_gauge_desc, &psy_cfg);
As soon as devm_power_supply_register() has called device_add()
the external_power_changed callback can get called. So there is a window
where fuel_gauge_external_power_changed() may get called while
info->bat has not been set yet leading to a NULL pointer dereference.
Fixing this is easy. The external_power_changed callback gets passed
the power_supply which will eventually get stored in info->bat,
so fuel_gauge_external_power_changed() can simply directly use
the passed in psy argument which is always valid.
Fixes: 30abb3d079 ("power: supply: axp288_fuel_gauge: Take lock before updating the valid flag")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 003fb0a511 upstream.
Requests to the mmc layer usually come through a block device IO.
The exceptions are the ioctl interface, RPMB chardev ioctl
and debugfs, which issue their own blk_mq requests through
blk_execute_rq and do not query the BLK_STS error but the
mmcblk-internal drv_op_result. This patch ensures that drv_op_result
defaults to an error and has to be overwritten by the operation
to be considered successful.
The behavior leads to a bug where the request never propagates
the error, e.g. by directly erroring out at mmc_blk_mq_issue_rq if
mmc_blk_part_switch fails. The ioctl caller of the rpmb chardev then
can never see an error (BLK_STS_IOERR, but drv_op_result is unchanged)
and thus may assume that their call executed successfully when it did not.
While always checking the blk_execute_rq return value would be
advised, let's eliminate the error by always setting
drv_op_result as -EIO to be overwritten on success (or other error)
Fixes: 614f0388f5 ("mmc: block: move single ioctl() commands to block requests")
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/59c17ada35664b818b7bd83752119b2d@hyperstone.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d180891fba upstream.
Some calls to rpc_exit_task() may deliberately change the value of
task->tk_status, for instance because it gets checked by the RPC call's
rpc_release() callback. That makes it wrong to reset the value to
task->tk_rpc_status.
In particular this causes a bug where the rpc_call_done() callback tries
to fail over a set of pNFS/flexfiles writes to a different IP address,
but the reset of task->tk_status causes nfs_commit_release_pages() to
immediately mark the file as having a fatal error.
Fixes: 39494194f9 ("SUNRPC: Fix races with rpc_killall_tasks()")
Cc: stable@vger.kernel.org # 6.1.x
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81302b1c7c upstream.
It's reported that the recording started right after the driver probe
doesn't work properly, and it turned out that this is related with the
codec auto-suspend. Namely, after the probe phase, the usage count
goes zero, and the auto-suspend is programmed, but the codec is kept
still active until the auto-suspend expiration. When an application
(e.g. alsactl) updates the mixer values at this moment, the values are
cached but not actually written. Then, starting arecord thereafter
also results in the silence because of the missing unmute.
The root cause is the handling of "lazy update" mode; when a mixer
value is updated *after* the suspend, it should update only the cache
and exits. At the resume, the cached value is written to the device,
in turn. The problem is that the current code misinterprets the state
of auto-suspend as if it were already suspended.
Although we can add the check of the actual device state after
pm_runtime_get_if_in_use() for catching the missing state, this won't
suffice; the second call of regmap_update_bits_check() will skip
writing the register because the cache has been already updated by the
first call. So we'd need fixes in two different places.
OTOH, a simpler fix is to replace pm_runtime_get_if_in_use() with
pm_runtime_get_if_active() (with ign_usage_count=true). This change
implies that the driver takes the pm refcount if the device is still
in ACTIVE state and continues the processing. A small caveat is that
this will leave the auto-suspend timer. But, since the timer callback
itself checks the device state and aborts gracefully when it's active,
this won't be any substantial problem.
Long story short: we address the missing register-write problem just
by replacing the pm_runtime_*() call in snd_hda_keep_power_up().
Fixes: fc4f000bf8 ("ALSA: hda - Fix unexpected resume through regmap code path")
Reported-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Closes: https://lore.kernel.org/r/a7478636-af11-92ab-731c-9b13c582a70d@linux.intel.com
Suggested-by: Cezary Rojewski <cezary.rojewski@intel.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230518113520.15213-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce0b15d11a upstream.
The INVLPG instruction is used to invalidate TLB entries for a
specified virtual address. When PCIDs are enabled, INVLPG is supposed
to invalidate TLB entries for the specified address for both the
current PCID *and* Global entries. (Note: Only kernel mappings set
Global=1.)
Unfortunately, some INVLPG implementations can leave Global
translations unflushed when PCIDs are enabled.
As a workaround, never enable PCIDs on affected processors.
I expect there to eventually be microcode mitigations to replace this
software workaround. However, the exact version numbers where that
will happen are not known today. Once the version numbers are set in
stone, the processor list can be tweaked to only disable PCIDs on
affected processors with affected microcode.
Note: if anyone wants a quick fix that doesn't require patching, just
stick 'nopcid' on your kernel command-line.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de3004c874 upstream.
In preparation for removing security_old_inode_init_security(), switch to
security_inode_init_security().
Extend the existing ocfs2_initxattrs() to take the
ocfs2_security_xattr_info structure from fs_info, and populate the
name/value/len triple with the first xattr provided by LSMs.
As fs_info was not used before, ocfs2_initxattrs() can now handle the case
of replicating the behavior of security_old_inode_init_security(), i.e.
just obtaining the xattr, in addition to setting all xattrs provided by
LSMs.
Supporting multiple xattrs is not currently supported where
security_old_inode_init_security() was called (mknod, symlink), as it
requires non-trivial changes that can be done at a later time. Like for
reiserfs, even if EVM is invoked, it will not provide an xattr (if it is
not the first to set it, its xattr will be discarded; if it is the first,
it does not have xattrs to calculate the HMAC on).
Finally, since security_inode_init_security(), unlike
security_old_inode_init_security(), returns zero instead of -EOPNOTSUPP if
no xattrs were provided by LSMs or if inodes are private, additionally
check in ocfs2_init_security_get() if the xattr name is set.
If not, act as if security_old_inode_init_security() returned -EOPNOTSUPP,
and set si->enable to zero to notify to the functions following
ocfs2_init_security_get() that no xattrs are available.
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Reviewed-by: Casey Schaufler <casey@schaufler-ca.com>
Acked-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Reviewed-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4eda19cc8a upstream.
The watchdog countdown is supposed to begin when the device file is
opened. Instead, it would begin countdown upon the first write to or
close of the device file. Now, the ping operation is called within the
start operation which ensures the countdown begins. From experimenation,
it does not appear possible to do this with a single write including
both the start bit and the trigger bit. So, it is done as two distinct
writes.
Signed-off-by: Gregory Oakes <gregory.oakes@amd.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230316201312.17538-1-gregory.oakes@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 99d4645062 ]
Set TPM_CHIP_FLAG_SUSPENDED in tpm_pm_suspend() and reset in
tpm_pm_resume(). While the flag is set, tpm_hwrng() gives back zero
bytes. This prevents hwrng from racing during resume.
Cc: stable@vger.kernel.org
Fixes: 6e592a065d ("tpm: Move Linux RNG connection to hwrng")
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c8862de05 ]
TPM chip bootstrapping was removed from tpm_chip_register(), and it
was relocated to tpm_tis_core. This breaks all drivers which are not
based on tpm_tis because the chip will not get properly initialized.
Take the corrective steps:
1. Rename tpm_chip_startup() as tpm_chip_bootstrap() and make it one-shot.
2. Call tpm_chip_bootstrap() in tpm_chip_register(), which reverts the
things as tehy used to be.
Cc: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Fixes: 548eb516ec ("tpm, tpm_tis: startup chip before testing for interrupts")
Reported-by: Pengfei Xu <pengfei.xu@intel.com>
Link: https://lore.kernel.org/all/ZEjqhwHWBnxcaRV5@xpf.sh.intel.com/
Tested-by: Pengfei Xu <pengfei.xu@intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Stable-dep-of: 99d4645062 ("tpm: Prevent hwrng from activating during resume")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 548eb516ec ]
In tpm_tis_gen_interrupt() a request for a property value is sent to the
TPM to test if interrupts are generated. However after a power cycle the
TPM responds with TPM_RC_INITIALIZE which indicates that the TPM is not
yet properly initialized.
Fix this by first starting the TPM up before the request is sent. For this
the startup implementation is removed from tpm_chip_register() and put
into the new function tpm_chip_startup() which is called before the
interrupts are tested.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Stable-dep-of: 99d4645062 ("tpm: Prevent hwrng from activating during resume")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1398aa803f ]
Before sending a TPM command, CLKRUN protocol must be disabled. This is not
done in the case of tpm1_do_selftest() call site inside tpm_tis_resume().
Address this by decorating the calls with tpm_chip_{start,stop}, which
should be always used to arm and disarm the TPM chip for transmission.
Finally, move the call to the main TPM driver callback as the last step
because it should arm the chip by itself, if it needs that type of
functionality.
Cc: stable@vger.kernel.org
Reported-by: Jason A. Donenfeld <Jason@zx2c4.com>
Closes: https://lore.kernel.org/linux-integrity/CS68AWILHXS4.3M36M1EKZLUMS@suppilovahvero/
Fixes: a3fbfae82b ("tpm: take TPM chip power gating out of tpm_transmit()")
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e87fcf0dc2 ]
According to the TPM Interface Specification (TIS) support for "stsValid"
and "commandReady" interrupts is only optional.
This has to be taken into account when handling the interrupts in functions
like wait_for_tpm_stat(). To determine the supported interrupts use the
capability query.
Also adjust wait_for_tpm_stat() to only wait for interrupt reported status
changes. After that process all the remaining status changes by polling
the status register.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Tested-by: Michael Niewöhner <linux@mniewoehner.de>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Stable-dep-of: 1398aa803f ("tpm_tis: Use tpm_chip_{start,stop} decoration inside tpm_tis_resume")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 858e8b792d ]
The interrupt handler that sets the boolean variable irq_tested may run on
another CPU as the thread that checks irq_tested as part of the irq test in
tpm_tis_send().
Since nothing guarantees cache coherency between CPUs for unsynchronized
accesses to boolean variables the testing thread might not perceive the
value change done in the interrupt handler.
Avoid this issue by setting the bit TPM_TIS_IRQ_TESTED in the flags field
of the tpm_tis_data struct and by accessing this field with the bit
manipulating functions that provide cache coherency.
Also convert all other existing sites to use the proper macros when
accessing this bitfield.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Tested-by: Michael Niewöhner <linux@mniewoehner.de>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Stable-dep-of: 1398aa803f ("tpm_tis: Use tpm_chip_{start,stop} decoration inside tpm_tis_resume")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e8ef34e36 ]
When work in gadget mode, currently driver doesn't update software level
link_state correctly as link state change event is not enabled for most
devices, in function dwc3_gadget_suspend_interrupt(), it will only pass
suspend event to UDC core when software level link state changes, so when
interrupt generated in sequences of suspend -> reset -> conndone ->
suspend, link state is not updated during reset and conndone, so second
suspend interrupt event will not pass to UDC core.
Remove link_state compare in dwc3_gadget_suspend_interrupt() and add a
suspended flag to replace the compare function.
Fixes: 799e9dc829 ("usb: dwc3: gadget: conditionally disable Link State change events")
Cc: stable <stable@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Link: https://lore.kernel.org/r/20230512004524.31950-1-quic_linyyuan@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b951b0efb ]
Commit c76c6c4ecb ("ARM: 9294/2: vfp: Fix broken softirq handling
with instrumentation enabled") updated the VFP exception entry logic to
go via a C function, so that we get the compiler's version of
local_bh_disable(), which may be instrumented, and isn't generally
callable from assembler.
However, this assumes that passing an alternative 'success' return
address works in C as it does in asm, and this is only the case if the C
calls in question are tail calls, as otherwise, the stack will need some
unwinding as well.
I have already sent patches to the list that replace most of the asm
logic with C code, and so it is preferable to have a minimal fix that
addresses the issue and can be backported along with the commit that it
fixes to v6.3 from v6.4. Hopefully, we can land the C conversion for v6.5.
So instead of passing the 'success' return address as a function
argument, pass the stack address from where to pop it so that both LR
and SP have the expected value.
Fixes: c76c6c4ecb ("ARM: 9294/2: vfp: Fix broken softirq handling with ...")
Reported-by: syzbot+d4b00edc2d0c910d4bf4@syzkaller.appspotmail.com
Tested-by: syzbot+d4b00edc2d0c910d4bf4@syzkaller.appspotmail.com
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c76c6c4ecb ]
Commit 62b95a7b44 ("ARM: 9282/1: vfp: Manipulate task VFP state with
softirqs disabled") replaced the en/disable preemption calls inside the
VFP state handling code with en/disabling of soft IRQs, which is
necessary to allow kernel use of the VFP/SIMD unit when handling a soft
IRQ.
Unfortunately, when lockdep is enabled (or other instrumentation that
enables TRACE_IRQFLAGS), the disable path implemented in asm fails to
perform the lockdep and RCU related bookkeeping, resulting in spurious
warnings and other badness.
Set let's rework the VFP entry code a little bit so we can make the
local_bh_disable() call from C, with all the instrumentations that
happen to have been configured. Calling local_bh_enable() can be done
from asm, as it is a simple wrapper around __local_bh_enable_ip(), which
is always a callable function.
Link: https://lore.kernel.org/all/ZBBYCSZUJOWBg1s8@localhost.localdomain/
Fixes: 62b95a7b44 ("ARM: 9282/1: vfp: Manipulate task VFP state with softirqs disabled")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c4c597f1b3 upstream.
The mte_sync_page_tags() function sets PG_mte_tagged if it initializes
page tags. Then we return to mte_sync_tags(), which sets PG_mte_tagged
again. At best, this is redundant. However, it is possible for
mte_sync_page_tags() to return without having initialized tags for the
page, i.e. in the case where check_swap is true (non-compound page),
is_swap_pte(old_pte) is false and pte_is_tagged is false. So at worst,
we set PG_mte_tagged on a page with uninitialized tags. This can happen
if, for example, page migration causes a PTE for an untagged page to
be replaced. If the userspace program subsequently uses mprotect() to
enable PROT_MTE for that page, the uninitialized tags will be exposed
to userspace.
Fix it by removing the redundant call to set_page_mte_tagged().
Fixes: e059853d14 ("arm64: mte: Fix/clarify the PG_mte_tagged semantics")
Signed-off-by: Peter Collingbourne <pcc@google.com>
Cc: <stable@vger.kernel.org> # 6.1
Link: https://linux-review.googlesource.com/id/Ib02d004d435b2ed87603b858ef7480f7b1463052
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com>
Link: https://lore.kernel.org/r/20230420214327.2357985-1-pcc@google.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2efbafb91e upstream.
Consider the following sequence of events:
1) A page in a PROT_READ|PROT_WRITE VMA is faulted.
2) Page migration allocates a page with the KASAN allocator,
causing it to receive a non-match-all tag, and uses it
to replace the page faulted in 1.
3) The program uses mprotect() to enable PROT_MTE on the page faulted in 1.
As a result of step 3, we are left with a non-match-all tag for a page
with tags accessible to userspace, which can lead to the same kind of
tag check faults that commit e74a684680 ("arm64: Reset KASAN tag in
copy_highpage with HW tags only") intended to fix.
The general invariant that we have for pages in a VMA with VM_MTE_ALLOWED
is that they cannot have a non-match-all tag. As a result of step 2, the
invariant is broken. This means that the fix in the referenced commit
was incomplete and we also need to reset the tag for pages without
PG_mte_tagged.
Fixes: e5b8d92189 ("arm64: mte: reset the page tag in page->flags")
Cc: <stable@vger.kernel.org> # 5.15
Link: https://linux-review.googlesource.com/id/I7409cdd41acbcb215c2a7417c1e50d37b875beff
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20230420210945.2313627-1-pcc@google.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2862a2fdfa upstream.
Use "a" constraint instead of "d" constraint to pass the state parameter to
the do_sqbs() inline assembly. This prevents that general purpose register
zero is used for the state parameter.
If the compiler would select general purpose register zero this would be
problematic for the used instruction in rsy format: the register used for
the state parameter is a base register. If the base register is general
purpose register zero the contents of the register are unexpectedly ignored
when the instruction is executed.
This only applies to z/VM guests using QIOASSIST with dedicated (pass through)
QDIO-based devices such as FCP [zfcp driver] as well as real OSA or
HiperSockets [qeth driver].
A possible symptom for this case using zfcp is the following repeating kernel
message pattern:
zfcp <devbusid>: A QDIO problem occurred
zfcp <devbusid>: A QDIO problem occurred
zfcp <devbusid>: qdio: ZFCP on SC <sc> using AI:1 QEBSM:1 PRI:1 TDD:1 SIGA: W
zfcp <devbusid>: A QDIO problem occurred
zfcp <devbusid>: A QDIO problem occurred
Each of the qdio problem message can be accompanied by the following entries
for the affected subchannel <sc> in
/sys/kernel/debug/s390dbf/qdio_error/hex_ascii for zfcp or qeth:
<sc> ccq: 69....
<sc> SQBS ERROR.
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Cc: Steffen Maier <maier@linux.ibm.com>
Fixes: 8129ee1642 ("[PATCH] s390: qdio V=V pass-through")
Cc: <stable@vger.kernel.org>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c99bff3429 upstream.
Formatting a thin-provisioned (ESE) device that is part of a PPRC copy
relation might fail with the following error:
dasd-eckd 0.0.f500: An error occurred in the DASD device driver, reason=09
[...]
24 Byte: 0 MSG 4, no MSGb to SYSOP
During format of an ESE disk the Release Allocated Space command is used.
A bit in the payload of the command is set that is not allowed to be set
for devices in a copy relation. This bit is set to allow the partial
release of an extent.
Check for the existence of a copy relation before setting the respective
bit.
Fixes: 91dc4a1975 ("s390/dasd: Add new ioctl to release space")
Cc: stable@kernel.org # 5.3+
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Link: https://lore.kernel.org/r/20230519102340.3854819-2-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 35a4b8ce4a upstream.
Since commit 85e031154c ("powerpc/bpf: Perform complete extra passes
to update addresses"), two additional passes are performed to avoid
space and CPU time wastage on powerpc. But these extra passes led to
WARN_ON_ONCE() hits in bpf_add_extable_entry() as extable entries are
populated again, during the extra pass, without resetting the index.
Fix it by resetting entry index before repopulating extable entries,
if and when there is an additional pass.
Fixes: 85e031154c ("powerpc/bpf: Perform complete extra passes to update addresses")
Cc: stable@vger.kernel.org # v6.3+
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Reviewed-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230425065829.18189-1-hbathini@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66b2ca0862 upstream.
It was reported that soft dirty tracking doesn't work when using the
Radix MMU.
The tracking is supposed to work by clearing the soft dirty bit for a
mapping and then write protecting the PTE. If/when the page is written
to, a page fault occurs and the soft dirty bit is added back via
pte_mkdirty(). For example in wp_page_reuse():
entry = maybe_mkwrite(pte_mkdirty(entry), vma);
if (ptep_set_access_flags(vma, vmf->address, vmf->pte, entry, 1))
update_mmu_cache(vma, vmf->address, vmf->pte);
Unfortunately on radix _PAGE_SOFTDIRTY is being dropped by
radix__ptep_set_access_flags(), called from ptep_set_access_flags(),
meaning the soft dirty bit is not set even though the page has been
written to.
Fix it by adding _PAGE_SOFTDIRTY to the set of bits that are able to be
changed in radix__ptep_set_access_flags().
Fixes: b0b5e9b130 ("powerpc/mm/radix: Add radix pte #defines")
Cc: stable@vger.kernel.org # v4.7+
Reported-by: Dan Horák <dan@danny.cz>
Link: https://lore.kernel.org/r/20230511095558.56663a50f86bdc4cd97700b7@danny.cz
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230511114224.977423-1-mpe@ellerman.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f7aacc5eb upstream.
For an SR-IOV device, while enabling DDW, a new table is created and
added at index 1 in the group. In the below 2 scenarios, the table is
incorrectly referenced at index 0 (which is where the table is for
default DMA window).
1. When adding DDW
This issue is exposed with "slub_debug". Error thrown out from
dma_iommu_dma_supported()
Warning: IOMMU offset too big for device mask
mask: 0xffffffff, table offset: 0x800000000000000
2. During Dynamic removal of the PCI device.
Error is from iommu_tce_table_put() since a NULL table pointer is
passed in.
Fixes: 381ceda88c ("powerpc/pseries/iommu: Make use of DDW for indirect mapping")
Cc: stable@vger.kernel.org # v5.15+
Signed-off-by: Gaurav Batra <gbatra@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230505184701.91613-1-gbatra@linux.vnet.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a784452872 upstream.
Current only one entry is enabled but IP itself is using 4 different IDs
which are already listed in zynqmp.dtsi.
sata: ahci@fd0c0000 {
compatible = "ceva,ahci-1v84";
...
iommus = <&smmu 0x4c0>, <&smmu 0x4c1>,
<&smmu 0x4c2>, <&smmu 0x4c3>;
};
Fixes: 8ac47837f0 ("arm64: dts: zynqmp: Add missing iommu IDs")
Cc: stable@vger.kernel.org # v5.12+
Signed-off-by: Michal Simek <michal.simek@amd.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d5aa417808 upstream.
This code was written prior to previous updates to this
logic for other chips. The RSC registers are part of
SMUIO which is an always on block so there is no need
to disable gfxoff. Additionally add the carryover and
preemption checks.
v2: rebase
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.1.y: 5591a051b8: drm/amdgpu: refine get gpu clock counter method
Cc: stable@vger.kernel.org # 6.2.y: 5591a051b8: drm/amdgpu: refine get gpu clock counter method
Cc: stable@vger.kernel.org # 6.3.y: 5591a051b8: drm/amdgpu: refine get gpu clock counter method
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5591a051b8 upstream.
[why]
regGOLDEN_TSC_COUNT_LOWER/regGOLDEN_TSC_COUNT_UPPER are protected and
unaccessible under sriov.
The clock counter high bit may update during reading process.
[How]
Replace regGOLDEN_TSC_COUNT_LOWER/regGOLDEN_TSC_COUNT_UPPER with
regCP_MES_MTIME_LO/regCP_MES_MTIME_HI to get gpu clock under sriov.
Refine get gpu clock counter method to make the result more precise.
Signed-off-by: Tong Liu01 <Tong.Liu01@amd.com>
Acked-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68518294d0 upstream.
Implement get_vbios_fb_size() so we can properly reserve
the vbios splash screen to avoid potential artifacts on the
screen during the transition from the pre-OS console to the
OS console.
Acked-by: Sunil Khatri <sunil.khatri@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.1.x
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f949f140f upstream.
The driver have a race, experienced only with PREEMPT_RT patchset:
CPU0 | CPU1
==================================================================
qcom_geni_serial_probe |
uart_add_one_port |
| serdev_drv_probe
| qca_serdev_probe
| serdev_device_open
| uart_open
| uart_startup
| qcom_geni_serial_startup
| enable_irq
| __irq_startup
| WARN_ON()
| IRQ not activated
request_threaded_irq |
irq_domain_activate_irq |
The warning:
894000.serial: ttyHS1 at MMIO 0x894000 (irq = 144, base_baud = 0) is a MSM
serial serial0: tty port ttyHS1 registered
WARNING: CPU: 7 PID: 107 at kernel/irq/chip.c:241 __irq_startup+0x78/0xd8
...
qcom_geni_serial 894000.serial: serial engine reports 0 RX bytes in!
Adding UART port triggers probe of child serial devices - serdev and
eventually Qualcomm Bluetooth hci_qca driver. This opens UART port
which enables the interrupt before it got activated in
request_threaded_irq(). The issue originates in commit f3974413cf
("tty: serial: qcom_geni_serial: Wakeup IRQ cleanup") and discussion on
mailing list [1]. However the above commit does not explain why the
uart_add_one_port() is moved above requesting interrupt.
[1] https://lore.kernel.org/all/5d9f3dfa.1c69fb81.84c4b.30bf@mx.google.com/
Fixes: f3974413cf ("tty: serial: qcom_geni_serial: Wakeup IRQ cleanup")
Cc: <stable@vger.kernel.org>
Cc: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20230505152301.2181270-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95d698869b upstream.
Possibly the last PCI controller-based (i.e. not a soft/winmodem)
dial-up modem one can still buy.
Looks to have a stock XR17C154 PCI UART chip for communication, but for
some reason when provisioning the PCI IDs they swapped the vendor and
subvendor IDs. Otherwise this card would have worked out of the box.
Searching online, some folks seem to not have this issue and others do,
so it is possible only some batches of cards have this error.
Create a new macro to handle the switched IDs and add support here.
Signed-off-by: Andrew Davis <afd@ti.com>
Cc: stable <stable@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230420160209.28221-1-afd@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04fc781608 upstream.
The zswap writeback mechanism can cause a race condition resulting in
memory corruption, where a swapped out page gets swapped in with data that
was written to a different page.
The race unfolds like this:
1. a page with data A and swap offset X is stored in zswap
2. page A is removed off the LRU by zpool driver for writeback in
zswap-shrink work, data for A is mapped by zpool driver
3. user space program faults and invalidates page entry A, offset X is
considered free
4. kswapd stores page B at offset X in zswap (zswap could also be
full, if so, page B would then be IOed to X, then skip step 5.)
5. entry A is replaced by B in tree->rbroot, this doesn't affect the
local reference held by zswap-shrink work
6. zswap-shrink work writes back A at X, and frees zswap entry A
7. swapin of slot X brings A in memory instead of B
The fix:
Once the swap page cache has been allocated (case ZSWAP_SWAPCACHE_NEW),
zswap-shrink work just checks that the local zswap_entry reference is
still the same as the one in the tree. If it's not the same it means that
it's either been invalidated or replaced, in both cases the writeback is
aborted because the local entry contains stale data.
Reproducer:
I originally found this by running `stress` overnight to validate my work
on the zswap writeback mechanism, it manifested after hours on my test
machine. The key to make it happen is having zswap writebacks, so
whatever setup pumps /sys/kernel/debug/zswap/written_back_pages should do
the trick.
In order to reproduce this faster on a vm, I setup a system with ~100M of
available memory and a 500M swap file, then running `stress --vm 1
--vm-bytes 300000000 --vm-stride 4000` makes it happen in matter of tens
of minutes. One can speed things up even more by swinging
/sys/module/zswap/parameters/max_pool_percent up and down between, say, 20
and 1; this makes it reproduce in tens of seconds. It's crucial to set
`--vm-stride` to something other than 4096 otherwise `stress` won't
realize that memory has been corrupted because all pages would have the
same data.
Link: https://lkml.kernel.org/r/20230503151200.19707-1-cerasuolodomenico@gmail.com
Signed-off-by: Domenico Cerasuolo <cerasuolodomenico@gmail.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Chris Li (Google) <chrisl@kernel.org>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Vitaly Wool <vitaly.wool@konsulko.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed40866ec7 upstream.
s390's struct statfs and struct statfs64 contain padding, which
field-by-field copying does not set. Initialize the respective structs
with zeros before filling them and copying them to userspace, like it's
already done for the compat versions of these structs.
Found by KMSAN.
[agordeev@linux.ibm.com: fixed typo in patch description]
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Link: https://lore.kernel.org/r/20230504144021.808932-2-iii@linux.ibm.com
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit afb2acb2e3 upstream.
In kvm_vm_ioctl_create_vcpu(), add vcpu to vcpu_array iff it's safe to
access vcpu via kvm_get_vcpu() and kvm_for_each_vcpu(), i.e. when there's
no failure path requiring vcpu removal and destruction. Such order is
important because vcpu_array accessors may end up referencing vcpu at
vcpu_array[0] even before online_vcpus is set to 1.
When online_vcpus=0, any call to kvm_get_vcpu() goes through
array_index_nospec() and ends with an attempt to xa_load(vcpu_array, 0):
int num_vcpus = atomic_read(&kvm->online_vcpus);
i = array_index_nospec(i, num_vcpus);
return xa_load(&kvm->vcpu_array, i);
Similarly, when online_vcpus=0, a kvm_for_each_vcpu() does not iterate over
an "empty" range, but actually [0, ULONG_MAX]:
xa_for_each_range(&kvm->vcpu_array, idx, vcpup, 0, \
(atomic_read(&kvm->online_vcpus) - 1))
In both cases, such online_vcpus=0 edge case, even if leading to
unnecessary calls to XArray API, should not be an issue; requesting
unpopulated indexes/ranges is handled by xa_load() and xa_for_each_range().
However, this means that when the first vCPU is created and inserted in
vcpu_array *and* before online_vcpus is incremented, code calling
kvm_get_vcpu()/kvm_for_each_vcpu() already has access to that first vCPU.
This should not pose a problem assuming that once a vcpu is stored in
vcpu_array, it will remain there, but that's not the case:
kvm_vm_ioctl_create_vcpu() first inserts to vcpu_array, then requests a
file descriptor. If create_vcpu_fd() fails, newly inserted vcpu is removed
from the vcpu_array, then destroyed:
vcpu->vcpu_idx = atomic_read(&kvm->online_vcpus);
r = xa_insert(&kvm->vcpu_array, vcpu->vcpu_idx, vcpu, GFP_KERNEL_ACCOUNT);
kvm_get_kvm(kvm);
r = create_vcpu_fd(vcpu);
if (r < 0) {
xa_erase(&kvm->vcpu_array, vcpu->vcpu_idx);
kvm_put_kvm_no_destroy(kvm);
goto unlock_vcpu_destroy;
}
atomic_inc(&kvm->online_vcpus);
This results in a possible race condition when a reference to a vcpu is
acquired (via kvm_get_vcpu() or kvm_for_each_vcpu()) moments before said
vcpu is destroyed.
Signed-off-by: Michal Luczaj <mhal@rbox.co>
Message-Id: <20230510140410.1093987-2-mhal@rbox.co>
Cc: stable@vger.kernel.org
Fixes: c5b0775491 ("KVM: Convert the kvm->vcpus array to a xarray", 2021-12-08)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f0f4a2ef7 upstream.
Until now, the page table walker counted increments to the PA and IPA
of a walk in two separate places. While the PA is incremented as soon as
a leaf PTE is installed in stage2_map_walker_try_leaf(), the IPA is
actually bumped in the generic table walker context. Critically,
__kvm_pgtable_visit() rereads the PTE after the LEAF callback returns
to work out if a table or leaf was installed, and only bumps the IPA for
a leaf PTE.
This arrangement worked fine when we handled faults behind the write lock,
as the walker had exclusive access to the stage-2 page tables. However,
commit 1577cb5823 ("KVM: arm64: Handle stage-2 faults in parallel")
started handling all stage-2 faults behind the read lock, opening up a
race where a walker could increment the PA but not the IPA of a walk.
Nothing good ensues, as the walker starts mapping with the incorrect
IPA -> PA relationship.
For example, assume that two vCPUs took a data abort on the same IPA.
One observes that dirty logging is disabled, and the other observed that
it is enabled:
vCPU attempting PMD mapping vCPU attempting PTE mapping
====================================== =====================================
/* install PMD */
stage2_make_pte(ctx, leaf);
data->phys += granule;
/* replace PMD with a table */
stage2_try_break_pte(ctx, data->mmu);
stage2_make_pte(ctx, table);
/* table is observed */
ctx.old = READ_ONCE(*ptep);
table = kvm_pte_table(ctx.old, level);
/*
* map walk continues w/o incrementing
* IPA.
*/
__kvm_pgtable_walk(..., level + 1);
Bring an end to the whole mess by using the IPA as the single source of
truth for how far along a walk has gotten. Work out the correct PA to
map by calculating the IPA offset from the beginning of the walk and add
that to the starting physical address.
Cc: stable@vger.kernel.org
Fixes: 1577cb5823 ("KVM: arm64: Handle stage-2 faults in parallel")
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230421071606.1603916-2-oliver.upton@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7b8b8ed99 upstream.
clc length is now accepted to <= 8 less than length,
rather than < 8.
Solve issues on some of Axis's smb clients which send
messages where clc length is 8 bytes less than length.
The specific client was running kernel 4.19.217 with
smb dialect 3.0.2 on armv7l.
Cc: stable@vger.kernel.org
Signed-off-by: Gustav Johansson <gustajo@axis.com>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 59a556aebc upstream.
In cifs_oplock_break function we drop reference to a cfile at
the end of function, due to which close command goes on wire
after lease break acknowledgment even if file is already closed
by application but we had deferred the handle close.
If other client with limited file shareaccess waiting on lease
break ack proceeds operation on that file as soon as first client
sends ack, then we may encounter status sharing violation error
because of open handle.
Solution is to put reference to cfile(send close on wire if last ref)
and then send oplock acknowledgment to server.
Fixes: 9e31678fb4 ("SMB3: fix lease break timeout when multiple deferred close handles for the same file.")
Cc: stable@kernel.org
Signed-off-by: Bharath SM <bharathsm@microsoft.com>
Reviewed-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47592fa8eb upstream.
Oplock break may occur for different file handle than the deferred
handle. Check for inode deferred closes list, if it's not empty then
close all the deferred handles of inode because we should not cache
handles if we dont have handle lease.
Eg: If openfilelist has one deferred file handle and another open file
handle from app for a same file, then on a lease break we choose the
first handle in openfile list. The first handle in list can be deferred
handle or actual open file handle from app. In case if it is actual open
handle then today, we don't close deferred handles if we lose handle lease
on a file. Problem with this is, later if app decides to close the existing
open handle then we still be caching deferred handles until deferred close
timeout. Leaving open handle may result in sharing violation when windows
client tries to open a file with limited file share access.
So we should check for deferred list of inode and walk through the list of
deferred files in inode and close all deferred files.
Fixes: 9e31678fb4 ("SMB3: fix lease break timeout when multiple deferred close handles for the same file.")
Cc: stable@kernel.org
Signed-off-by: Bharath SM <bharathsm@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60fc756fc8 upstream.
The probe() id argument may be NULL in 2 scenarios:
1. brcmf_pcie_pm_leave_D3() calling brcmf_pcie_probe() to reprobe
the device.
2. If a user tries to manually bind the driver from sysfs then the sdio /
pcie / usb probe() function gets called with NULL as id argument.
1. Is being hit by users causing the following oops on resume and causing
wifi to stop working:
BUG: kernel NULL pointer dereference, address: 0000000000000018
<snip>
Hardware name: Dell Inc. XPS 13 9350/0PWNCR, BIDS 1.13.0 02/10/2020
Workgueue: events_unbound async_run_entry_fn
RIP: 0010:brcmf_pcie_probe+Ox16b/0x7a0 [brcmfmac]
<snip>
Call Trace:
<TASK>
brcmf_pcie_pm_leave_D3+0xc5/8x1a0 [brcmfmac be3b4cefca451e190fa35be8f00db1bbec293887]
? pci_pm_resume+0x5b/0xf0
? pci_legacy_resume+0x80/0x80
dpm_run_callback+0x47/0x150
device_resume+0xa2/0x1f0
async_resume+0x1d/0x30
<snip>
Fix this by checking for id being NULL.
In the PCI and USB cases try a manual lookup of the id so that manually
binding the driver through sysfs and more importantly brcmf_pcie_probe()
on resume will work.
For the SDIO case there is no helper to do a manual sdio_device_id lookup,
so just directly error out on a NULL id there.
Fixes: da6d9c8ecd ("wifi: brcmfmac: add firmware vendor info in driver info")
Reported-by: Felix <nimrod4garoa@gmail.com>
Link: https://lore.kernel.org/regressions/4ef3f252ff530cbfa336f5a0d80710020fc5cb1e.camel@gmail.com/
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230510141856.46532-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 262d7a52ba upstream.
Under certain circumstances we send two EFLUSH commands, resulting in two
EFLUSH ack packets, while only expecting a single EFLUSH ack.
This can cause the driver Tx flush completion to get out of sync.
To avoid this problem, don't enable the "Transmit buffer flush done" (TFD)
interrupt and remove the code handling it.
Now we only send EFLUSH command after receiving status packet with
"Init detected" (IDET) bit set.
Fixes: 26ad340e58 ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/r/20230516134318.104279-6-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe82f16aaf upstream.
This incorrect tracking caused unnecessary ring expansion in some
usecases which over days of use consume a lot of memory.
xhci driver tries to keep track of free transfer blocks (TRBs) on the
ring buffer, but failed to add back some cancelled transfers that were
turned into no-op operations instead of just moving past them.
This can happen if there are several queued pending transfers which
then are cancelled in reverse order.
Solve this by counting the numer of steps we move the dequeue pointer
once we complete a transfer, and add it to the number of free trbs
instead of just adding the trb number of the current transfer.
This way we ensure we count the no-op trbs on the way as well.
Fixes: 55f6153d8c ("xhci: remove extra loop in interrupt context")
Cc: stable@vger.kernel.org
Reported-by: Miller Hunter <MillerH@hearthnhome.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217242
Tested-by: Miller Hunter <MillerH@hearthnhome.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230515134059.161110-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c0f4f09c0 upstream.
The CDC-ECM specification [1] requires to send the host MAC address as
an uppercase hexadecimal string in chapter "5.4 Ethernet Networking
Functional Descriptor":
The Unicode character is chosen from the set of values 30h through
39h and 41h through 46h (0-9 and A-F).
However, snprintf(.., "%pm", ..) generates a lowercase MAC address
string. While most host drivers are tolerant to this, UsbNcm.sys on
Windows 10 is not. Instead it uses a different MAC address with all
bytes set to zero including and after the first byte containing a
lowercase letter. On Windows 11 Microsoft fixed it, but apparently they
did not backport the fix.
This change fixes the issue by upper-casing the MAC to comply with the
specification.
[1]: https://www.usb.org/document-library/class-definitions-communication-devices-12, file ECM120.pdf
Fixes: bcd4a1c40b ("usb: gadget: u_ether: construct with default values and add setters/getters")
Cc: stable@vger.kernel.org
Signed-off-by: Konrad Gräfe <k.graefe@gateware.de>
Link: https://lore.kernel.org/r/20230505143640.443014-1-k.graefe@gateware.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8540870af upstream.
Prevent -ETIMEDOUT error on .suspend().
e.g. If gadget driver is loaded and we are connected to a USB host,
all transfers must be stopped before stopping the controller else
we will not get a clean stop i.e. dwc3_gadget_run_stop() will take
several seconds to complete and will return -ETIMEDOUT.
Handle error cases properly in dwc3_gadget_suspend().
Simplify dwc3_gadget_resume() by using the introduced helper function.
Fixes: 9f8a67b65a ("usb: dwc3: gadget: fix gadget suspend/resume")
Cc: stable@vger.kernel.org
Suggested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230503110048.30617-1-rogerq@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a398d5eac6 upstream.
With faulty usb-storage devices, read/write can timeout, in that case
the SCSI layer will abort and re-issue the command. USB storage has no
internal timeout, it relies on SCSI layer aborting commands via
.eh_abort_handler() for non those responsive devices.
After two consecutive timeouts of the same command, SCSI layer calls
.eh_device_reset_handler(), without calling .eh_abort_handler() first.
With usb-storage, this causes a deadlock:
-> .eh_device_reset_handler
-> device_reset
-> mutex_lock(&(us->dev_mutex));
mutex already by usb_stor_control_thread(), which is waiting for
command completion:
-> usb_stor_control_thread (mutex taken here)
-> usb_stor_invoke_transport
-> usb_stor_Bulk_transport
-> usb_stor_bulk_srb
-> usb_stor_bulk_transfer_sglist
-> usb_sg_wait
Make sure we cancel any pending command in .eh_device_reset_handler()
to avoid this.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Cc: linux-usb@vger.kernel.org
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/all/ZEllnjMKT8ulZbJh@sakura/
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20230505114759.1189741-1-mbizon@freebox.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 89dcd87ce5 ]
When CONFIG_BRIDGE_VLAN_FILTERING is disabled, two functions are still
defined but have no prototype or caller. This causes a W=1 warning for
the missing prototypes:
net/bridge/br_netlink_tunnel.c:29:6: error: no previous prototype for 'vlan_tunid_inrange' [-Werror=missing-prototypes]
net/bridge/br_netlink_tunnel.c:199:5: error: no previous prototype for 'br_vlan_tunnel_info' [-Werror=missing-prototypes]
The functions are already contitional on CONFIG_BRIDGE_VLAN_FILTERING,
and I coulnd't easily figure out the right set of #ifdefs, so just
move the declarations out of the #ifdef to avoid the warning,
at a small cost in code size over a more elaborate fix.
Fixes: 188c67dd19 ("net: bridge: vlan options: add support for tunnel id dumping")
Fixes: 569da08228 ("net: bridge: vlan options: add support for tunnel mapping set/del")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230516194625.549249-3-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61ae320a29 ]
There is no guarantee that rb_prev() will not return NULL in nft_rbtree_gc_elem():
general protection fault, probably for non-canonical address 0xdffffc0000000003: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000018-0x000000000000001f]
nft_add_set_elem+0x14b0/0x2990
nf_tables_newsetelem+0x528/0xb30
Furthermore, there is a possible use-after-free while iterating,
'node' can be free'd so we need to cache the next value to use.
Fixes: c9e6978e27 ("netfilter: nft_set_rbtree: Switch to node list walk for overlap detection")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3c361b8ac ]
nft_trans_FOO objects all share a common nft_trans base structure, but
trailing fields depend on the real object size. Access is only safe after
trans->msg_type check.
Check for rule type first. Found by code inspection.
Fixes: 1a94e38d25 ("netfilter: nf_tables: add NFTA_RULE_ID attribute")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ba9485b87 ]
The cited commit added a stray colon to the 'v' option. That makes the
option work incorrectly.
ex:
tools/testing/selftests/net# ./fib_nexthops.sh -v
(should enable verbose mode, instead it shows help text due to missing arg)
Fixes: 5feba47273 ("selftests: fib_nexthops: Make ping timeout configurable")
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c46e78ba9a ]
The XPCS expects clause 73 (copper backplane) autoneg to follow the
ethtool autoneg bit. It actually did that until the blamed
commit inaptly replaced state->an_enabled (coming from ethtool) with
phylink_autoneg_inband() (coming from the device tree or struct
phylink_config), as part of an unrelated phylink_pcs API conversion.
Russell King suggests that state->an_enabled from the original code was
just a proxy for the ethtool Autoneg bit, and that the correct way of
restoring the functionality is to check for this bit in the advertising
mask.
Fixes: 11059740e6 ("net: pcs: xpcs: convert to phylink_pcs_ops")
Link: https://lore.kernel.org/netdev/ZGNt2MFeRolKGFck@shell.armlinux.org.uk/
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60829145f1 ]
In suspend and resume cycle, the removal and rescan of device ends
up in NULL pointer dereference.
During driver initialization, if the ipc_imem_wwan_channel_init()
fails to get the valid device capabilities it returns an error and
further no resource (wwan struct) will be allocated. Now in this
situation if driver removal procedure is initiated it would result
in NULL pointer exception since unallocated wwan struct is dereferenced
inside ipc_wwan_deinit().
ipc_imem_run_state_worker() to handle the called functions return value
and to release the resource in failure case. It also reports the link
down event in failure cases. The user space application can handle this
event to do a device reset for restoring the device communication.
Fixes: 3670970dd8 ("net: iosm: shared memory IPC interface")
Reported-by: Samuel Wein PhD <sam@samwein.com>
Closes: https://lore.kernel.org/netdev/20230427140819.1310f4bd@kernel.org/T/
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60d758659f ]
In igb_hash_mc_addr() the expression:
"mc_addr[4] >> 8 - bit_shift", right shifting "mc_addr[4]"
shift by more than 7 bits always yields zero, so hash becomes not so different.
Add initialization with bit_shift = 1 and add a loop condition to ensure
bit_shift will be always in [1..8] range.
Fixes: 9d5c824399 ("igb: PCI-Express 82575 Gigabit Ethernet driver")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1323e0c6e1 ]
According to datasheet, the command opcode must be specified
into bits [14:12] of the Extended Port Control register (EPC).
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Marco Migliore <m.migliore@tiesse.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 412cd77a2c ]
cas_saturn_firmware_init() allocates some memory using vmalloc(). This
memory is freed in the .remove() function but not it the error handling
path of the probe.
Add the missing vfree() to avoid a memory leak, should an error occur.
Fixes: fcaa40669c ("cassini: use request_firmware")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6352dae09 ]
'__net_initdata' becomes a no-op with CONFIG_NET_NS=y, but when this
option is disabled it becomes '__initdata', which means the data can be
freed after the initialization phase. This annotation is obviously
incorrect for the devlink net device notifier block which is still
registered after the initialization phase [1].
Fix this crash by removing the '__net_initdata' annotation.
[1]
general protection fault, probably for non-canonical address 0xcccccccccccccccc: 0000 [#1] PREEMPT SMP
CPU: 3 PID: 117 Comm: (udev-worker) Not tainted 6.4.0-rc1-custom-gdf0acdc59b09 #64
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.2-1.fc37 04/01/2014
RIP: 0010:notifier_call_chain+0x58/0xc0
[...]
Call Trace:
<TASK>
dev_set_mac_address+0x85/0x120
dev_set_mac_address_user+0x30/0x50
do_setlink+0x219/0x1270
rtnl_setlink+0xf7/0x1a0
rtnetlink_rcv_msg+0x142/0x390
netlink_rcv_skb+0x58/0x100
netlink_unicast+0x188/0x270
netlink_sendmsg+0x214/0x470
__sys_sendto+0x12f/0x1a0
__x64_sys_sendto+0x24/0x30
do_syscall_64+0x38/0x80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Fixes: e93c9378e3 ("devlink: change per-devlink netdev notifier to static one")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Closes: https://lore.kernel.org/netdev/600ddf9e-589a-2aa0-7b69-a438f833ca10@samsung.com/
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230515162925.1144416-1-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e81a6cba5 ]
In a SCSI request, storvsc pre-allocates space for up to
MAX_PAGE_BUFFER_COUNT physical frame numbers to be passed to Hyper-V. If
the size of the I/O request requires more PFNs, a separate memory area of
exactly the correct size is dynamically allocated.
But when the pre-allocated area is used, current code always passes
MAX_PAGE_BUFFER_COUNT PFNs to Hyper-V, even if fewer are needed. While
this doesn't break anything because the additional PFNs are always zero,
more bytes than necessary are copied into the VMBus channel ring buffer.
This takes CPU cycles and wastes space in the ring buffer. For a typical 4
Kbyte I/O that requires only a single PFN, 248 unnecessary bytes are
copied.
Fix this by setting the payload_sz based on the actual number of PFNs
required, not the size of the pre-allocated space.
Reported-by: John Starks <jostarks@microsoft.com>
Fixes: 8f43710543 ("scsi: storvsc: Support PAGE_SIZE larger than 4K")
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/1684171241-16209-1-git-send-email-mikelley@microsoft.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3ae69180b ]
The DBGI dump is (unsurprisingly) of type DBGI, not SRAM.
This leads to bad register accesses because the union is
built differently, there's no allocation ID, and thus the
allocation ID ends up being 0x8000.
Note that this was already wrong for DRAM vs. SMEM since
they use different parts of the union, but the allocation
ID is at the same place, so it worked.
Fix all of this but set the allocation ID in a way that
the offset calculation ends up without any offset.
Fixes: 34bc27783a ("iwlwifi: yoyo: fix DBGI_SRAM ini dump header.")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230514120631.19a302ae4c65.I12272599f7c1930666157b9d5e7f81fe9ec4c421@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7dcbdf2928 ]
When the user disables rxvlan offloading and then changes the number of
channels, all VLAN ports are unable to receive traffic.
Changing the number of channels triggers a VFR reset. During re-init, when
VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS is received, we do:
1 - set the IAVF_FLAG_SETUP_NETDEV_FEATURES flag
2 - call
iavf_set_vlan_offload_features(adapter, 0, netdev->features);
The second step sends to the PF the __default__ features, in this case
aq_required |= IAVF_FLAG_AQ_ENABLE_CTAG_VLAN_STRIPPING
While the first step forces the watchdog task to call
netdev_update_features() -> iavf_set_features() ->
iavf_set_vlan_offload_features(adapter, netdev->features, features).
Since the user disabled the "rxvlan", this sets:
aq_required |= IAVF_FLAG_AQ_DISABLE_CTAG_VLAN_STRIPPING
When we start processing the AQ commands, both flags are enabled. Since we
process DISABLE_XTAG first then ENABLE_XTAG, this results in the PF
enabling the rxvlan offload. This breaks all communications on the VLAN
net devices.
Fix by removing the call to iavf_set_vlan_offload_features() (second
step). Calling netdev_update_features() from watchdog task is enough for
both init and reset paths.
Fixes: 7598f4b40b ("iavf: Move netdev_update_features() into watchdog task")
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7255355a06 ]
Fix the current implementation that causes ice_trigger_vf_reset()
to start resetting the VF even when the VF-NIC is still initializing.
When we reset NIC with ice driver it can interfere with
iavf-vf initialization e.g. during consecutive resets induced by ice
iavf ice
| |
|<-----------------|
| ice resets vf
iavf |
reset |
start |
|<-----------------|
| ice resets vf
| causing iavf
| initialization
| error
| |
iavf
reset
end
This leads to a series of -53 errors
(failed to init adminq) from the IAVF.
Change the state of the vf_state field to be not active when the IAVF
is still initializing. Make sure to wait until receiving the message on
the message box to ensure that the vf is ready and initializded.
In simple terms we use the ACTIVE flag to make sure that the ice
driver knows if the iavf is ready for another reset
iavf ice
| |
| |
|<------------- ice resets vf
iavf vf_state != ACTIVE
reset |
start |
| |
| |
iavf |
reset-------> vf_state == ACTIVE
end ice resets vf
| |
| |
Fixes: c54d209c78 ("ice: Wait for VF to be reset/ready before configuration")
Signed-off-by: Dawid Wesierski <dawidx.wesierski@intel.com>
Signed-off-by: Kamil Maziarz <kamil.maziarz@intel.com>
Acked-by: Jacob Keller <Jacob.e.keller@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab7470bc6d ]
After a core PF reset, the VFs were showing wrong Rx/Tx stats. This is a
regression in commit 6624e780a5 ("ice: split ice_vsi_setup into smaller
functions") caused by missing to set "stat_offsets_loaded = false" in the
ice_vsi_rebuild() path.
Fixes: 6624e780a5 ("ice: split ice_vsi_setup into smaller functions")
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 225c657945 ]
Removing the phy_stop() from bcmgenet_netif_stop() ended up causing
warnings from the PHY library that phy_start() is called from the
RUNNING state since we are no longer stopping the PHY state machine
during bcmgenet_suspend().
Restore the call to phy_stop() but make it conditional on being called
from the close or suspend path.
Fixes: c96e731c93 ("net: bcmgenet: connect and disconnect from the PHY state machine")
Fixes: 93e0401e0f ("net: bcmgenet: Remove phy_stop() from bcmgenet_netif_stop()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://lore.kernel.org/r/20230515025608.2587012-1-f.fainelli@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93e0401e0f ]
The call to phy_stop() races with the later call to phy_disconnect(),
resulting in concurrent phy_suspend() calls being run from different
CPUs. The final call to phy_disconnect() ensures that the PHY is
stopped and suspended, too.
Fixes: c96e731c93 ("net: bcmgenet: connect and disconnect from the PHY state machine")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 225c657945 ("net: bcmgenet: Restore phy_stop() depending upon suspend/close")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1b0d5aec1 ]
Currently when the new channel-path is enabled, we do evaluation only
on the subchannels with a device connected on it. This is because,
in the past, if the device in the subchannel is not working or not
available, we used to unregister the subchannels. But, from the 'commit
2297791c92 ("s390/cio: dont unregister subchannel from child-drivers")'
we allow subchannels with or without an active device connected
on it. So, when we do the io_subchannel_verify, make sure that,
we are evaluating the subchannels without any device too.
Fixes: 2297791c92 ("s390/cio: dont unregister subchannel from child-drivers")
Reported-by: Boris Fiuczynski <fiuczy@linux.ibm.com>
Signed-off-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35a089b5d7 ]
Checking the bearer min mtu with tipc_udp_mtu_bad() only works for
IPv4 UDP bearer, and IPv6 UDP bearer has a different value for the
min mtu. This patch checks with encap_hlen + TIPC_MIN_BEARER_MTU
for min mtu, which works for both IPv4 and IPv6 UDP bearer.
Note that tipc_udp_mtu_bad() is still used to check media min mtu
in __tipc_nl_media_set(), as m->mtu currently is only used by the
IPv4 UDP bearer as its default mtu value.
Fixes: 682cd3cf94 ("tipc: confgiure and apply UDP bearer MTU on running links")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56077b56cd ]
When doing link mtu negotiation, a malicious peer may send Activate msg
with a very small mtu, e.g. 4 in Shuang's testing, without checking for
the minimum mtu, l->mtu will be set to 4 in tipc_link_proto_rcv(), then
n->links[bearer_id].mtu is set to 4294967228, which is a overflow of
'4 - INT_H_SIZE - EMSG_OVERHEAD' in tipc_link_mss().
With tipc_link.mtu = 4, tipc_link_xmit() kept printing the warning:
tipc: Too large msg, purging xmit list 1 5 0 40 4!
tipc: Too large msg, purging xmit list 1 15 0 60 4!
And with tipc_link_entry.mtu 4294967228, a huge skb was allocated in
named_distribute(), and when purging it in tipc_link_xmit(), a crash
was even caused:
general protection fault, probably for non-canonical address 0x2100001011000dd: 0000 [#1] PREEMPT SMP PTI
CPU: 0 PID: 0 Comm: swapper/0 Kdump: loaded Not tainted 6.3.0.neta #19
RIP: 0010:kfree_skb_list_reason+0x7e/0x1f0
Call Trace:
<IRQ>
skb_release_data+0xf9/0x1d0
kfree_skb_reason+0x40/0x100
tipc_link_xmit+0x57a/0x740 [tipc]
tipc_node_xmit+0x16c/0x5c0 [tipc]
tipc_named_node_up+0x27f/0x2c0 [tipc]
tipc_node_write_unlock+0x149/0x170 [tipc]
tipc_rcv+0x608/0x740 [tipc]
tipc_udp_recv+0xdc/0x1f0 [tipc]
udp_queue_rcv_one_skb+0x33e/0x620
udp_unicast_rcv_skb.isra.72+0x75/0x90
__udp4_lib_rcv+0x56d/0xc20
ip_protocol_deliver_rcu+0x100/0x2d0
This patch fixes it by checking the new mtu against tipc_bearer_min_mtu(),
and not updating mtu if it is too small.
Fixes: ed193ece26 ("tipc: simplify link mtu negotiation")
Reported-by: Shuang Li <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ae6d66b60 ]
As different media may requires different min mtu, and even the
same media with different net family requires different min mtu,
add tipc_bearer_min_mtu() to calculate min mtu accordingly.
This API will be used to check the new mtu when doing the link
mtu negotiation in the next patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 56077b56cd ("tipc: do not update mtu if msg_max is too small in mtu negotiation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5306623a98 ]
When initializing XDP in virtnet_open(), some rq xdp initialization
may hit an error causing net device open failed. However, previous
rqs have already initialized XDP and enabled NAPI, which is not the
expected behavior. Need to roll back the previous rq initialization
to avoid leaks in error unwinding of init code.
Also extract helper functions of disable and enable queue pairs.
Use newly introduced disable helper function in error unwinding and
virtnet_close. Use enable helper function in virtnet_open.
Fixes: 754b8a21a9 ("virtio_net: setup xdp_rxq_info")
Signed-off-by: Feng Liu <feliu@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: William Tu <witu@nvidia.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ead9c98ca ]
In the implementation, the sent_frame count does not increment when
transmit errors occur. Therefore, bq_xmit_all() will take care of
returning the XDP frames.
Fixes: 26312c685a ("net: fec: correct the counting of XDP sent frames")
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c83b49383b ]
As the call trace shows, skb_panic was caused by wrong skb->mac_header
in nsh_gso_segment():
invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI
CPU: 3 PID: 2737 Comm: syz Not tainted 6.3.0-next-20230505 #1
RIP: 0010:skb_panic+0xda/0xe0
call Trace:
skb_push+0x91/0xa0
nsh_gso_segment+0x4f3/0x570
skb_mac_gso_segment+0x19e/0x270
__skb_gso_segment+0x1e8/0x3c0
validate_xmit_skb+0x452/0x890
validate_xmit_skb_list+0x99/0xd0
sch_direct_xmit+0x294/0x7c0
__dev_queue_xmit+0x16f0/0x1d70
packet_xmit+0x185/0x210
packet_snd+0xc15/0x1170
packet_sendmsg+0x7b/0xa0
sock_sendmsg+0x14f/0x160
The root cause is:
nsh_gso_segment() use skb->network_header - nhoff to reset mac_header
in skb_gso_error_unwind() if inner-layer protocol gso fails.
However, skb->network_header may be reset by inner-layer protocol
gso function e.g. mpls_gso_segment. skb->mac_header reset by the
inaccurate network_header will be larger than skb headroom.
nsh_gso_segment
nhoff = skb->network_header - skb->mac_header;
__skb_pull(skb,nsh_len)
skb_mac_gso_segment
mpls_gso_segment
skb_reset_network_header(skb);//skb->network_header+=nsh_len
return -EINVAL;
skb_gso_error_unwind
skb_push(skb, nsh_len);
skb->mac_header = skb->network_header - nhoff;
// skb->mac_header > skb->headroom, cause skb_push panic
Use correct mac_offset to restore mac_header and get rid of nhoff.
Fixes: c411ed8545 ("nsh: add GSO support")
Reported-by: syzbot+632b5d9964208bfef8c0@syzkaller.appspotmail.com
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Dong Chenchen <dongchenchen2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ef0785b30 ]
The empty stub functions are defined as global functions, which
causes a warning because of missing prototypes:
drivers/gpu/drm/exynos/exynos_drm_g2d.h:37:5: error: no previous prototype for 'g2d_open'
drivers/gpu/drm/exynos/exynos_drm_g2d.h:42:5: error: no previous prototype for 'g2d_close'
Mark them as 'static inline' to avoid the warning and to make
them behave as intended.
Fixes: eb4d9796fa ("drm/exynos: g2d: Convert to driver component API")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a93d2afd3f ]
When devm runs function in the "remove" path for a device it runs them
in the reverse order. That means that if you have parts of your driver
that aren't using devm or are using "roll your own" devm w/
devm_add_action_or_reset() you need to keep that in mind.
The mt8186 audio driver didn't quite get this right. Specifically, in
mt8186_init_clock() it called mt8186_audsys_clk_register() and then
went on to call a bunch of other devm function. The caller of
mt8186_init_clock() used devm_add_action_or_reset() to call
mt8186_deinit_clock() but, because of the intervening devm functions,
the order was wrong.
Specifically at probe time, the order was:
1. mt8186_audsys_clk_register()
2. afe_priv->clk = devm_kcalloc(...)
3. afe_priv->clk[i] = devm_clk_get(...)
At remove time, the order (which should have been 3, 2, 1) was:
1. mt8186_audsys_clk_unregister()
3. Free all of afe_priv->clk[i]
2. Free afe_priv->clk
The above seemed to be causing a use-after-free. Luckily, it's easy to
fix this by simply using devm more correctly. Let's move the
devm_add_action_or_reset() to the right place. In addition to fixing
the use-after-free, code inspection shows that this fixes a leak
(missing call to mt8186_audsys_clk_unregister()) that would have
happened if any of the syscon_regmap_lookup_by_phandle() calls in
mt8186_init_clock() had failed.
Fixes: 55b423d562 ("ASoC: mediatek: mt8186: support audio clock control in platform driver")
Signed-off-by: Douglas Anderson <dianders@chromium.org
Link: https://lore.kernel.org/r/20230511092437.1.I31cceffc8c45bb1af16eb613e197b3df92cdc19e@changeid
Signed-off-by: Mark Brown <broonie@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07a2730593 ]
The trace event recorded incorrect values for the registered family,
protocol, and port because the arguments are in the wrong order.
Fixes: b4af59328c ("SUNRPC: Trace server-side rpcbind registration events")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 948f072ada ]
Since the ->xprt_ctxt pointer was added to svc_deferred_req, it has not
been sufficient to use kfree() to free a deferred request. We may need
to free the ctxt as well.
As freeing the ctxt is all that ->xpo_release_rqst() does, we repurpose
it to explicit do that even when the ctxt is not stored in an rqst.
So we now have ->xpo_release_ctxt() which is given an xprt and a ctxt,
which may have been taken either from an rqst or from a dreq. The
caller is now responsible for clearing that pointer after the call to
->xpo_release_ctxt.
We also clear dr->xprt_ctxt when the ctxt is moved into a new rqst when
revisiting a deferred request. This ensures there is only one pointer
to the ctxt, so the risk of double freeing in future is reduced. The
new code in svc_xprt_release which releases both the ctxt and any
rq_deferred depends on this.
Fixes: 773f91b2cf ("SUNRPC: Fix NFSD's request deferral on RDMA transports")
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb8d3a2c80 ]
When an RPC request is deferred, the rq_xprt_ctxt pointer is moved out
of the svc_rqst into the svc_deferred_req.
When the deferred request is revisited, the pointer is copied into
the new svc_rqst - and also remains in the svc_deferred_req.
In the (rare?) case that the request is deferred a second time, the old
svc_deferred_req is reused - it still has all the correct content.
However in that case the rq_xprt_ctxt pointer is NOT cleared so that
when xpo_release_xprt is called, the ctxt is freed (UDP) or possible
added to a free list (RDMA).
When the deferred request is revisited for a second time, it will
reference this ctxt which may be invalid, and the free the object a
second time which is likely to oops.
So change svc_defer() to *always* clear rq_xprt_ctxt, and assert that
the value is now stored in the svc_deferred_req.
Fixes: 773f91b2cf ("SUNRPC: Fix NFSD's request deferral on RDMA transports")
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f5bb36bf9 ]
When Universal DVB card is detaching, netup_unidvb_dma_fini()
uses del_timer() to stop dma->timeout timer. But when timer
handler netup_unidvb_dma_timeout() is running, del_timer()
could not stop it. As a result, the use-after-free bug could
happen. The process is shown below:
(cleanup routine) | (timer routine)
| mod_timer(&dev->tx_sim_timer, ..)
netup_unidvb_finidev() | (wait a time)
netup_unidvb_dma_fini() | netup_unidvb_dma_timeout()
del_timer(&dma->timeout); |
| ndev->pci_dev->dev //USE
Fix by changing del_timer() to del_timer_sync().
Link: https://lore.kernel.org/linux-media/20230308125514.4208-1-duoming@zju.edu.cn
Fixes: 52b1eaf4c5 ("[media] netup_unidvb: NetUP Universal DVB-S/S2/T/T2/C PCI-E card driver")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b45d5ff8c ]
The timeout of the cmdq reset command has been increased to
resolve the reset timeout issue in the full VF scenario.
The timeout of other cmdq commands remains unchanged.
Fixes: 8d307f8e8c ("net: hns3: create new set of unified hclge_comm_cmd_send APIs")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 814d0c7860 ]
Currently the hns3 vf function reset delays 5000ms before vf rebuild
process. In product applications, this delay is too long for application
configurations and causes configuration timeout.
According to the tests, 500ms delay is enough for reset process except PF
FLR. So this patch modifies delay to 500ms in these scenarios.
Fixes: 6988eb2a9b ("net: hns3: Add support to reset the enet/ring mgmt layer")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f14db07064 ]
To prevent the system from abnormally sending PFC frames after an
abnormal reset. The hns3 driver notifies the firmware to disable pfc
before reset.
Fixes: 35d93a3004 ("net: hns3: adjust the process of PF reset")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89f6bfb071 ]
In function hns3_dump_tx_queue_info, The print buffer is not enough when
the tx BD number is configured to 32760. As a result several BD
information wouldn't be displayed.
So fix it by increasing the tx queue print buffer length.
Fixes: 630a6738da ("net: hns3: adjust string spaces of some parameters of tx bd info in debugfs")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec52b69c04 ]
When ports are in standalone mode, they should have learning disabled to
avoid adding new entries in the MAC lookup table which might be used by
other bridge ports to forward packets. While adding that, also make sure
learning is enabled for CPU port.
Fixes: 888cdb892b ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ebe9bc5095 ]
stp_set_state() should actually allow receiving BPDU while in LEARNING
mode which is not the case. Additionally, the BLOCKEN bit does not
actually forbid sending forwarded frames from that port. To fix this, add
a5psw_port_tx_enable() function which allows to disable TX. However, while
its name suggest that TX is totally disabled, it is not and can still
allow to send BPDUs even if disabled. This can be done by using forced
forwarding with the switch tagging mechanism but keeping "filtering"
disabled (which is already the case in the rzn1-a5sw tag driver). With
these fixes, STP support is now functional.
Fixes: 888cdb892b ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e4b45f20c ]
Currently, management frame were discarded before reaching the CPU port due
to a misconfiguration of the MGMT_CONFIG register. Enable them by setting
the correct value in this register in order to correctly receive management
frame and handle STP.
Fixes: 888cdb892b ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d80fc101d2 ]
In commit 20704bd163 ("erspan: build the header with the right proto
according to erspan_ver"), it gets the proto with t->parms.erspan_ver,
but t->parms.erspan_ver is not used by collect_md branch, and instead
it should get the proto with md->version for collect_md.
Thanks to Kevin for pointing this out.
Fixes: 20704bd163 ("erspan: build the header with the right proto according to erspan_ver")
Fixes: 94d7d8f292 ("ip6_gre: add erspan v2 support")
Reported-by: Kevin Traynor <ktraynor@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ab5fc55d7 ]
Smatch reports:
drivers/tty/serial/arc_uart.c:631 arc_serial_probe() warn:
'port->membase' from of_iomap() not released on lines: 631.
In arc_serial_probe(), if uart_add_one_port() fails,
port->membase is not released, which would cause a resource leak.
To fix this, I replace of_iomap with devm_platform_ioremap_resource.
Fixes: 8dbe1d5e09 ("serial/arc: inline the probe helper")
Signed-off-by: Ke Zhang <m202171830@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/r/20230428031636.44642-1-m202171830@hust.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 53558de2b5 ]
Now that DVB_CORE can be a loadable module, pvrusb2 can run into
a link error:
ld.lld: error: undefined symbol: dvb_module_probe
>>> referenced by pvrusb2-devattr.c
>>> drivers/media/usb/pvrusb2/pvrusb2-devattr.o:(pvr2_lgdt3306a_attach) in archive vmlinux.a
ld.lld: error: undefined symbol: dvb_module_release
>>> referenced by pvrusb2-devattr.c
>>> drivers/media/usb/pvrusb2/pvrusb2-devattr.o:(pvr2_dual_fe_attach) in archive vmlinux.a
Refine the Kconfig dependencies to avoid this case.
Link: https://lore.kernel.org/linux-media/20230117171055.2714621-1-arnd@kernel.org
Fixes: 7655c342db ("media: Kconfig: Make DVB_CORE=m possible when MEDIA_SUPPORT=y")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e306ec49a ]
When tcp_v4_send_reset() is called with @sk == NULL,
we do not change ctl_sk->sk_priority, which could have been
set from a prior invocation.
Change tcp_v4_send_reset() to set sk_priority and sk_mark
fields before calling ip_send_unicast_reply().
This means tcp_v4_send_reset() and tcp_v4_send_ack()
no longer have to clear ctl_sk->sk_mark after
their call to ip_send_unicast_reply().
Fixes: f6c0f5d209 ("tcp: honor SO_PRIORITY in TIME_WAIT state")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d4486efe9 ]
When client and server establish a connection through vsock,
the client send a request to the server to initiate the connection,
then start a timer to wait for the server's response. When the server's
RESPONSE message arrives, the timer also times out and exits. The
server's RESPONSE message is processed first, and the connection is
established. However, the client's timer also times out, the original
processing logic of the client is to directly set the state of this vsock
to CLOSE and return ETIMEDOUT. It will not notify the server when the port
is released, causing the server port remain.
when client's vsock_connect timeout，it should check sk state is
ESTABLISHED or not. if sk state is ESTABLISHED, it means the connection
is established, the client should not set the sk state to CLOSE
Note: I encountered this issue on kernel-4.18, which can be fixed by
this patch. Then I checked the latest code in the community
and found similar issue.
Fixes: d021c34405 ("VSOCK: Introduce VM Sockets")
Signed-off-by: Zhuang Shengen <zhuangshengen@huawei.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9113302bb4 ]
As not all ICE_TX_FLAGS_* fit in current 16-bit limited
tx_flags field that was introduced in the Fixes commit,
VLAN-related information would be discarded completely.
As such, creating a vlan and trying to run ping through
would result in no traffic passing.
Fix that by refactoring tx_flags variable into flags only and
a separate variable that holds VLAN ID. As there is some space left,
type variable can fit between those two. Pahole reports no size
change to ice_tx_buf struct.
Fixes: aa1d3faf71 ("ice: Robustify cleaning/completing XDP Tx buffers")
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92553ee031 ]
The Pavilion 15 line has B&O top speakers similar to the x360 and
applying the same profile produces good sound. Without this, the
sound would be tinny and underpowered without either applying
model=alc295-hp-x360 or booting another OS first.
Signed-off-by: Ryan Underwood <nemesis@icequake.net>
Fixes: 563785edfc ("ALSA: hda/realtek - Add quirk entry for HP Pavilion 15")
Link: https://lore.kernel.org/r/ZF0mpcMz3ezP9KQw@icequake.net
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b01db2740 ]
Introduce the W/A for packet errors seen with short cables (<1m) between
two DP83867 PHYs.
The W/A recommended by DM requires FFE Equalizer Configuration tuning by
writing value 0x0E81 to DSP_FFE_CFG register (0x012C), surrounded by hard
and soft resets as follows:
write_reg(0x001F, 0x8000); //hard reset
write_reg(DSP_FFE_CFG, 0x0E81);
write_reg(0x001F, 0x4000); //soft reset
Since DP83867 PHY DM says "Changing this register to 0x0E81, will not
affect Long Cable performance.", enable the W/A by default.
Fixes: 2a10154abc ("net: phy: dp83867: Add TI dp83867 phy")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f816b9829b ]
In the (unlikely) event that pm_runtime_get() (disguised as
pm_runtime_resume_and_get()) fails, the remove callback returned an
error early. The problem with this is that the driver core ignores the
error value and continues removing the device. This results in a
resource leak. Worse the devm allocated resources are freed and so if a
callback of the driver is called later the register mapping is already
gone which probably results in a crash.
Fixes: a31eda65ba ("net: fec: fix clock count mis-match")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230510200020.1534610-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e93c9378e3 ]
The commit 565b4824c3 ("devlink: change port event netdev notifier
from per-net to global") changed original per-net notifier to be
per-devlink instance. That fixed the issue of non-receiving events
of netdev uninit if that moved to a different namespace.
That worked fine in -net tree.
However, later on when commit ee75f1fc44 ("net/mlx5e: Create
separate devlink instance for ethernet auxiliary device") and
commit 72ed5d5624 ("net/mlx5: Suspend auxiliary devices only in
case of PCI device suspend") were merged, a deadlock was introduced
when removing a namespace with devlink instance with another nested
instance.
Here there is the bad flow example resulting in deadlock with mlx5:
net_cleanup_work -> cleanup_net (takes down_read(&pernet_ops_rwsem) ->
devlink_pernet_pre_exit() -> devlink_reload() ->
mlx5_devlink_reload_down() -> mlx5_unload_one_devl_locked() ->
mlx5_detach_device() -> del_adev() -> mlx5e_remove() ->
mlx5e_destroy_devlink() -> devlink_free() ->
unregister_netdevice_notifier() (takes down_write(&pernet_ops_rwsem)
Steps to reproduce:
$ modprobe mlx5_core
$ ip netns add ns1
$ devlink dev reload pci/0000:08:00.0 netns ns1
$ ip netns del ns1
Resolve this by converting the notifier from per-devlink instance to
a static one registered during init phase and leaving it registered
forever. Use this notifier for all devlink port instances created
later on.
Note what a tree needs this fix only in case all of the cited fixes
commits are present.
Reported-by: Moshe Shemesh <moshe@nvidia.com>
Fixes: 565b4824c3 ("devlink: change port event netdev notifier from per-net to global")
Fixes: ee75f1fc44 ("net/mlx5e: Create separate devlink instance for ethernet auxiliary device")
Fixes: 72ed5d5624 ("net/mlx5: Suspend auxiliary devices only in case of PCI device suspend")
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230510144621.932017-1-jiri@resnulli.us
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f97b8401e0 ]
On some distributions, the rp_filter is automatically set (=1) by
default on a netdev basis (also on VRFs).
In an SRv6 End.DT4 behavior, decapsulated IPv4 packets are routed using
the table associated with the VRF bound to that tunnel. During lookup
operations, the rp_filter can lead to packet loss when activated on the
VRF.
Therefore, we chose to make this selftest more robust by explicitly
disabling the rp_filter during tests (as it is automatically set by some
Linux distributions).
Fixes: 2195444e09 ("selftests: add selftest for the SRv6 End.DT4 behavior")
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Tested-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21a933c79a ]
The srv6_end_dt4_l3vpn_test instantiates a virtual network consisting of
several routers (rt-1, rt-2) and hosts.
When the IPv6 addresses of rt-{1,2} routers are configured, the Deduplicate
Address Detection (DAD) kicks in when enabled in the Linux distros running
the selftests. DAD is used to check whether an IPv6 address is already
assigned in a network. Such a mechanism consists of sending an ICMPv6 Echo
Request and waiting for a reply.
As the DAD process could take too long to complete, it may cause the
failing of some tests carried out by the srv6_end_dt4_l3vpn_test script.
To make the srv6_end_dt4_l3vpn_test more robust, we disable DAD on routers
since we configure the virtual network manually and do not need any address
deduplication mechanism at all.
Fixes: 2195444e09 ("selftests: add selftest for the SRv6 End.DT4 behavior")
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf3128a7ac ]
xfrm_state_find() uses `encap_family` of the current template with
the passed local and remote addresses to find a matching state.
If an optional tunnel or BEET mode template is skipped in a mixed-family
scenario, there could be a mismatch causing an out-of-bounds read as
the addresses were not replaced to match the family of the next template.
While there are theoretical use cases for optional templates in outbound
policies, the only practical one is to skip IPComp states in inbound
policies if uncompressed packets are received that are handled by an
implicitly created IPIP state instead.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Tobias Brunner <tobias@strongswan.org>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d776e31c8 ]
xfrm_state_find() uses `encap_family` of the current template with
the passed local and remote addresses to find a matching state.
If an optional tunnel or BEET mode template is skipped in a mixed-family
scenario, there could be a mismatch causing an out-of-bounds read as
the addresses were not replaced to match the family of the next template.
While there are theoretical use cases for optional templates in outbound
policies, the only practical one is to skip IPComp states in inbound
policies if uncompressed packets are received that are handled by an
implicitly created IPIP state instead.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Tobias Brunner <tobias@strongswan.org>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b409996eb ]
Downstream driver uses dpu->caps->smart_dma_rev to update
sspp->cap->features with the bit corresponding to the supported SmartDMA
version. Upstream driver does not do this, resulting in SSPP subdriver
not enabling setup_multirect callback. Add corresponding SmartDMA SSPP
feature bits to dpu hw catalog.
Per Abhinav's request enable the SmartDMA features only on the platforms
where the multirect was actually verified visually (sdm845 and sm8250).
An (untested) enablement on the rest of the platforms comes in the next
patch.
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/527362/
Link: https://lore.kernel.org/r/20230316161653.4106395-29-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Stable-dep-of: 701f69183d ("drm/msm/dpu: Fix PP_BLK_DIPHER -> DITHER typo")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5fc46f9421 ]
This reverts commit b0355dbbf1.
The reverted commit clears the secpath on packets received via xfrm interfaces
to support nested IPsec tunnels. This breaks Netfilter policy matching using
xt_policy in the FORWARD chain, as the secpath is missing during forwarding.
Additionally, Benedict Wong reports that it breaks Transport-in-Tunnel mode.
Fix this regression by reverting the commit until we have a better approach
for nested IPsec tunnels.
Fixes: b0355dbbf1 ("Fix XFRM-I support for nested ESP tunnels")
Link: https://lore.kernel.org/netdev/20230412085615.124791-1-martin@strongswan.org/
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94b95dfaa8 ]
Failure to add offloaded policy will cause to the following
error once user will try to reload driver.
Unregister_netdevice: waiting for eth3 to become free. Usage count = 2
This was caused by xfrm_dev_policy_add() which increments reference
to net_device. That reference was supposed to be decremented
in xfrm_dev_policy_free(). However the latter wasn't called.
unregister_netdevice: waiting for eth3 to become free. Usage count = 2
leaked reference.
xfrm_dev_policy_add+0xff/0x3d0
xfrm_policy_construct+0x352/0x420
xfrm_add_policy+0x179/0x320
xfrm_user_rcv_msg+0x1d2/0x3d0
netlink_rcv_skb+0xe0/0x210
xfrm_netlink_rcv+0x45/0x50
netlink_unicast+0x346/0x490
netlink_sendmsg+0x3b0/0x6c0
sock_sendmsg+0x73/0xc0
sock_write_iter+0x13b/0x1f0
vfs_write+0x528/0x5d0
ksys_write+0x120/0x150
do_syscall_64+0x3d/0x90
entry_SYSCALL_64_after_hwframe+0x46/0xb0
Fixes: 919e43fad5 ("xfrm: add an interface to offload policy")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 430cac4874 ]
The current code doesn't let a simple "allow" policy counteract a
default policy blocking all incoming packets:
ip x p setdefault in block
ip x p a src 192.168.2.1/32 dst 192.168.2.2/32 dir in action allow
At this stage, we have an allow policy (with or without transforms)
for this packet. It doesn't matter what the default policy says, since
the policy we looked up lets the packet through. The case of a
blocking policy is already handled separately, so we can remove this
check.
Fixes: 2d151d3907 ("xfrm: Add possibility to set the default to block if we have no policy")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 829632dae8 ]
The panic notifiers' callbacks execute in an atomic context, with
interrupts/preemption disabled, and all CPUs not running the panic
function are off, so it's very dangerous to wait on a regular
spinlock, there's a risk of deadlock.
Refactor the panic notifier of parisc/power driver to make use
of spin_trylock - for that, we've added a second version of the
soft-power function. Also, some comments were reorganized and
trailing white spaces, useless header inclusion and blank lines
were removed.
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Jeroen Roovers <jer@xs4all.nl>
Acked-by: Helge Deller <deller@gmx.de> # parisc
Signed-off-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ded99b89d2 ]
The Android Lenovo Yoga Book X90F / X90L uses the same charger / fuelgauge
setup as the already supported Windows Lenovo Yoga Book X91F/L, add
a DMI match for this to intel_cht_wc_models with driver_data
set to INTEL_CHT_WC_LENOVO_YOGABOOK1.
When the quirk for the X91F/L was initially added it was written to
also apply to the X90F/L but this does not work because the Android
version of the Yoga Book uses completely different DMI strings.
Also adjust the X91F/L quirk to reflect that it only applies to
the X91F/L models.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230301095402.28582-1-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e953796251 ]
This reverts commit
443a98e649 ("soundwire: bus: use pm_runtime_resume_and_get()")
Change calls to pm_runtime_resume_and_get() back to pm_runtime_get_sync().
This fixes a usage count underrun caused by doing a pm_runtime_put() even
though pm_runtime_resume_and_get() returned an error.
The three affected functions ignore -EACCES error from trying to get
pm_runtime, and carry on, including a put at the end of the function.
But pm_runtime_resume_and_get() does not increment the usage count if it
returns an error. So in the -EACCES case you must not call
pm_runtime_put().
The documentation for pm_runtime_get_sync() says:
"Consider using pm_runtime_resume_and_get() ... as this is likely to
result in cleaner code."
In this case I don't think it results in cleaner code because the
pm_runtime_put() at the end of the function would have to be conditional on
the return value from pm_runtime_resume_and_get() at the top of the
function.
pm_runtime_get_sync() doesn't have this problem because it always
increments the count, so always needs a put. The code can just flow through
and do the pm_runtime_put() unconditionally.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230406134640.8582-1-rf@opensource.cirrus.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2367e0ecb4 ]
There are two issues related to the number of ports coming from
Devicetree when exceeding in total QCOM_SDW_MAX_PORTS. Both lead to
incorrect memory accesses:
1. With DTS having too big value of input or output ports, the driver,
when copying port parameters from local/stack arrays into 'pconfig'
array in 'struct qcom_swrm_ctrl', will iterate over their sizes.
2. If DTS also has too many parameters for these ports (e.g.
qcom,ports-sinterval-low), the driver will overflow buffers on the
stack when reading these properties from DTS.
Add a sanity check so incorrect DTS will not cause kernel memory
corruption.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230222144412.237832-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 943fb67b09 ]
Coverity noted a place where we were not grabbing
the ses_lock when setting (and checking) ses_status.
Addresses-Coverity: 1536833 ("Data race condition (MISSING_LOCK)")
Reviewed-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Reviewed-by: Bharath SM <bharathsm@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64042c28c3 ]
RK3588 has a couple of hardware blocks called Native Interface Unit
(NIU) that gate the clocks to devices behind them. Effectively this
means that some clocks require two parent clocks being enabled.
Downstream implemented this by using a separate clock driver
("clk-link") for them, which enables the second clock using PM
framework.
In the upstream kernel we are currently missing support for the second
parent. The information about it is in the GATE_LINK() macro as
linkname, but that is not used. Thus the second parent clock is not
properly enabled. So far this did not really matter, since these clocks
are mostly required for the more advanced IP blocks, that are not yet
supported upstream. As this is about to change we need a fix. There
are three options available:
1. Properly implement support for having two parent clocks in the
clock framework.
2. Mark the affected clocks CLK_IGNORE_UNUSED, so that they are not
disabled. This wastes some power, but keeps the hack contained
within the clock driver. Going from this to the first solution
is easy once that has been implemented.
3. Enabling the extra clock in the consumer driver. This leaks some
implementation details into DT.
This patch implements the second option as an intermediate solution
until the first one is available. I used an alias for CLK_IS_CRITICAL,
so that it's easy to see which clocks are not really critical once
the clock framework supports a better way to implement this.
Tested-by: Vincent Legoll <vincent.legoll@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230403193250.108693-2-sebastian.reichel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed4b0661cc ]
pcie_relaxed_ordering_enabled() check was added to avoid a syndrome when
creating a MKey with relaxed ordering (RO) enabled when the driver's
relaxed_ordering_{read,write} HCA capabilities are out of sync with FW.
While this can happen with relaxed_ordering_read, it can't happen with
relaxed_ordering_write as it's set if the device supports RO write,
regardless of RO in PCI config space, and thus can't change during
runtime.
Therefore, drop the pcie_relaxed_ordering_enabled() check for
relaxed_ordering_write while keeping it for relaxed_ordering_read.
Doing so will also allow the usage of RO write in VFs and VMs (where RO
in PCI config space is not reported/emulated properly).
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Link: https://lore.kernel.org/r/7e8f55e31572c1702d69cae015a395d3a824a38a.1681131553.git.leon@kernel.org
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce38f3fc0f ]
x86 ACPI boards which ship with only Android as their factory image may
have pretty broken ACPI tables. This includes broken _AEI ACPI GPIO event
handlers, which are normally used to listen to the micro-USB ID pin and:
1. Switch the USB-mux to the host / device USB controllers
2. Disable Vbus path before enabling the 5V boost (AXP reg 0x30 bit 7)
3. Turn 5V Vboost on / off
On non broken systems where this is not done through an ACPI GPIO event
handler, there is an ACPI INT3496 device describing the involved GPIOs
which are handled by the extcon-intel-int3496 driver; and axp288-charger.ko
listens to this extcon-device and disables the Vbus path when necessary.
On x86 Android boards, with broken ACPI GPIO event handlers, these are
disabled by acpi_quirk_skip_gpio_event_handlers() and an intel-int3496
extcon device is manually instantiated by x86-android-tablets.ko .
Add support to the axp288-charger code for this setup, so that it
properly disables the Vbus path when necessary. Note this uses
acpi_quirk_skip_gpio_event_handlers() to identify these systems,
to avoid the need to add a separate DMI match table for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 67ea0b7ce4 ]
When an overflow occurs in the PRI queue, the SMMU toggles the overflow
flag in the PROD register. To exit the overflow condition, the PRI thread
is supposed to acknowledge it by toggling this flag in the CONS register.
Unacknowledged overflow causes the queue to stop adding anything new.
Currently, the priq thread always writes the CONS register back to the
SMMU after clearing the queue.
The writeback is not necessary if the OVFLG in the PROD register has not
been changed, no overflow has occured.
This commit checks the difference of the overflow flag between CONS and
PROD register. If it's different, toggles the OVACKFLG flag in the CONS
register and write it to the SMMU.
The situation is similar for the event queue.
The acknowledge register is also toggled after clearing the event
queue but never propagated to the hardware. This would only be done the
next time when executing evtq thread.
Unacknowledged event queue overflow doesn't affect the event
queue, because the SMMU still adds elements to that queue when the
overflow condition is active.
But it feel nicer to keep SMMU in sync when possible, so use the same
way here as well.
Signed-off-by: Tomas Krcka <krckatom@amazon.de>
Link: https://lore.kernel.org/r/20230329123420.34641-1-tomas.krcka@gmail.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4a2adbf35 ]
Older gcc versions get confused by comparing a u32 value to a negative
constant in a switch()/case block:
drivers/clk/tegra/clk-tegra20.c: In function 'tegra20_clk_measure_input_freq':
drivers/clk/tegra/clk-tegra20.c:581:2: error: case label does not reduce to an integer constant
case OSC_CTRL_OSC_FREQ_12MHZ:
^~~~
drivers/clk/tegra/clk-tegra20.c:593:2: error: case label does not reduce to an integer constant
case OSC_CTRL_OSC_FREQ_26MHZ:
Make the constants unsigned instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230227085914.2560984-1-arnd@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec275bf969 ]
In a previous commit c1006bd13146, ni->mi.mrec in ni_write_inode()
could be NULL, and thus a NULL check is added for this variable.
However, in the same call stack, ni->mi.mrec can be also dereferenced
in ni_clear():
ntfs_evict_inode(inode)
ni_write_inode(inode, ...)
ni = ntfs_i(inode);
is_rec_inuse(ni->mi.mrec) -> Add a NULL check by previous commit
ni_clear(ntfs_i(inode))
is_rec_inuse(ni->mi.mrec) -> No check
Thus, a possible null-pointer dereference may exist in ni_clear().
To fix it, a NULL check is added in this function.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1226113473 ]
Some platforms support more than 128 stream matching groups than what is
defined by the ARM SMMU architecture specification. But due to some unknown
reasons, those additional groups don't exhibit the same behavior as the
architecture supported ones.
For instance, the additional groups will not detect the quirky behavior of
some firmware versions intercepting writes to S2CR register, thus skipping
the quirk implemented in the driver and causing boot crash.
So let's limit the groups to 128 for now until the issue with those groups
are fixed and issue a notice to users in that case.
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230327080029.11584-1-manivannan.sadhasivam@linaro.org
[will: Reworded the comment slightly]
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa4d540b41 ]
GCC-13 (and Clang)[1] does not like to access a partially allocated
object, since it cannot reason about it for bounds checking.
In this case 140 bytes are allocated for an object of type struct
ib_umad_packet:
packet = kzalloc(sizeof(*packet) + IB_MGMT_RMPP_HDR, GFP_KERNEL);
However, notice that sizeof(*packet) is only 104 bytes:
struct ib_umad_packet {
struct ib_mad_send_buf * msg; /* 0 8 */
struct ib_mad_recv_wc * recv_wc; /* 8 8 */
struct list_head list; /* 16 16 */
int length; /* 32 4 */
/* XXX 4 bytes hole, try to pack */
struct ib_user_mad mad __attribute__((__aligned__(8))); /* 40 64 */
/* size: 104, cachelines: 2, members: 5 */
/* sum members: 100, holes: 1, sum holes: 4 */
/* forced alignments: 1, forced holes: 1, sum forced holes: 4 */
/* last cacheline: 40 bytes */
} __attribute__((__aligned__(8)));
and 36 bytes extra bytes are allocated for a flexible-array member in
struct ib_user_mad:
include/rdma/ib_mad.h:
120 enum {
...
123 IB_MGMT_RMPP_HDR = 36,
... }
struct ib_user_mad {
struct ib_user_mad_hdr hdr; /* 0 64 */
/* --- cacheline 1 boundary (64 bytes) --- */
__u64 data[] __attribute__((__aligned__(8))); /* 64 0 */
/* size: 64, cachelines: 1, members: 2 */
/* forced alignments: 1 */
} __attribute__((__aligned__(8)));
So we have sizeof(*packet) + IB_MGMT_RMPP_HDR == 140 bytes
Then the address of the flex-array member (for which only 36 bytes were
allocated) is casted and copied into a pointer to struct ib_rmpp_mad,
which, in turn, is of size 256 bytes:
rmpp_mad = (struct ib_rmpp_mad *) packet->mad.data;
struct ib_rmpp_mad {
struct ib_mad_hdr mad_hdr; /* 0 24 */
struct ib_rmpp_hdr rmpp_hdr; /* 24 12 */
u8 data[220]; /* 36 220 */
/* size: 256, cachelines: 4, members: 3 */
};
The thing is that those 36 bytes allocated for flex-array member data
in struct ib_user_mad onlly account for the size of both struct ib_mad_hdr
and struct ib_rmpp_hdr, but nothing is left for array u8 data[220].
So, the compiler is legitimately complaining about accessing an object
for which not enough memory was allocated.
Apparently, the only members of struct ib_rmpp_mad that are relevant
(that are actually being used) in function ib_umad_write() are mad_hdr
and rmpp_hdr. So, instead of casting packet->mad.data to
(struct ib_rmpp_mad *) create a new structure
struct ib_rmpp_mad_hdr {
struct ib_mad_hdr mad_hdr;
struct ib_rmpp_hdr rmpp_hdr;
} __packed;
and cast packet->mad.data to (struct ib_rmpp_mad_hdr *).
Notice that
IB_MGMT_RMPP_HDR == sizeof(struct ib_rmpp_mad_hdr) == 36 bytes
Refactor the rest of the code, accordingly.
Fix the following warnings seen under GCC-13 and -Warray-bounds:
drivers/infiniband/core/user_mad.c:564:50: warning: array subscript ‘struct ib_rmpp_mad[0]’ is partly outside array bounds of ‘unsigned char[140]’ [-Warray-bounds=]
drivers/infiniband/core/user_mad.c:566:42: warning: array subscript ‘struct ib_rmpp_mad[0]’ is partly outside array bounds of ‘unsigned char[140]’ [-Warray-bounds=]
drivers/infiniband/core/user_mad.c:618:25: warning: array subscript ‘struct ib_rmpp_mad[0]’ is partly outside array bounds of ‘unsigned char[140]’ [-Warray-bounds=]
drivers/infiniband/core/user_mad.c:622:44: warning: array subscript ‘struct ib_rmpp_mad[0]’ is partly outside array bounds of ‘unsigned char[140]’ [-Warray-bounds=]
Link: https://github.com/KSPP/linux/issues/273
Link: https://godbolt.org/z/oYWaGM4Yb [1]
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/ZBpB91qQcB10m3Fw@work
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 857d423c74 ]
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties. As
part of this, convert of_get_property/of_find_property calls to the
recently added of_property_present() helper when we just want to test
for presence of a property and nothing more.
Signed-off-by: Rob Herring <robh@kernel.org>
[mpe: Drop change in ppc4xx_probe_pci_bridge(), formatting]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230310144657.1541039-1-robh@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04e82793f0 ]
When we unbind a serial port hardware specific 8250 driver, the generic
serial8250 driver takes over the port. After that we see an oops about 10
seconds later. This can produce the following at least on some TI SoCs:
Unhandled fault: imprecise external abort (0x1406)
Internal error: : 1406 [#1] SMP ARM
Turns out that we may still have the serial port hardware specific driver
port->pm in use, and serial8250_pm() tries to call it after the port
specific driver is gone:
serial8250_pm [8250_base] from uart_change_pm+0x54/0x8c [serial_base]
uart_change_pm [serial_base] from uart_hangup+0x154/0x198 [serial_base]
uart_hangup [serial_base] from __tty_hangup.part.0+0x328/0x37c
__tty_hangup.part.0 from disassociate_ctty+0x154/0x20c
disassociate_ctty from do_exit+0x744/0xaac
do_exit from do_group_exit+0x40/0x8c
do_group_exit from __wake_up_parent+0x0/0x1c
Let's fix the issue by calling serial8250_set_defaults() in
serial8250_unregister_port(). This will set the port back to using
the serial8250 default functions, and sets the port->pm to point to
serial8250_pm.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230418101407.12403-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dac3b19210 ]
PD3.0 Spec 6.4.4.3.2 say that only Responder supports 12 or more SVIDs,
the Discover SVIDs Command Shall be executed multiple times until a
Discover SVIDs VDO is returned ending either with a SVID value of
0x0000 in the last part of the last VDO or with a VDO containing two
SVIDs with values of 0x0000.
In the current implementation, if the last VDO does not find that the
Discover SVIDs Command would be executed multiple times even if the
Responder SVIDs are less than 12, and we found some odd dockers just
meet this case. So fix it.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Link: https://lore.kernel.org/r/20230316081149.24519-1-frank.wang@rock-chips.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bea407a427 ]
Some devices will include battery status usages in the HID descriptor
but we won't see that battery data for one reason or another. For example,
AES sensors won't send battery data unless an AES pen is in proximity.
If a user does not have an AES pen but instead only interacts with the
AES touchscreen with their fingers then there is no need for us to create
a battery object. Similarly, if a family of peripherals shares the same
HID descriptor between wired-only and wireless-capable SKUs, users of the
former may never see a battery event and will not want a power_supply
object created.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217062
Link: https://gitlab.gnome.org/GNOME/gnome-control-center/-/issues/2354
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Tested-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bddcfb0802 ]
We have SOF and generic ACP support enabled for Rembrandt and
pheonix platforms on some machines. Since we have same PCI id
used for probing, add check for machine configuration flag to
avoid conflict with newer pci drivers. Such machine flag has
been initialized via dmi match on few Chrome machines. If no
flag is specified probe and register older platform device.
Signed-off-by: Syed Saba Kareem <Syed.SabaKareem@amd.com>
Reviewed-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230412091638.1158901-1-Syed.SabaKareem@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 326e1c208f ]
On some ACPI platforms (namely the ASUS Zenbook UM325) the _DSM method must
not be called after a notification is received but instead the mailbox
should be read immediately from RAM. This is because the ACPI interrupt
handler destroys the CCI in ERAM after copying to system memory, and when
_DSM is later called to perform a second copy, it retrieves a garbage
value.
Instead, the _DSM(read) method should only be called when necessary, i.e.
for polling the state after reset and for retrieving the version. Other
reads should not call _DSM and only peek into the RAM region.
This adds a separate read operation for the Zenbook that syncs the
ACPI mailbox only with polled commands.
Link: https://lore.kernel.org/linux-usb/20210823180626.tb6m7h5tp6adhvt2@fastboi.localdomain/
Signed-off-by: Samuel Čavoj <samuel@cavoj.net>
[ heikki : handling everything in ucsi_acpi.c with DMI quirk ]
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230405134456.49607-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87c614175b ]
When using gpio based chip select the cs value can go outside the range
0 – 3. The various MX51_ECSPI_* macros did not take this into consideration
resulting in possible corruption of the configuration.
For example for any cs value over 3 the SCLKPHA bits would not be set and
other values in the register possibly corrupted.
One way to fix this is to just mask the cs bits to 2 bits. This still
allows all 4 native chip selects to work as well as gpio chip selects
(which can use any of the 4 chip select configurations).
Signed-off-by: Kevin Groeneveld <kgroeneveld@lenbrook.com>
Link: https://lore.kernel.org/r/20230318222132.3373-1-kgroeneveld@lenbrook.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5b3691d15e ]
Now that USB HID++ devices can gather a serial number that matches the
one that would be gathered when connected through a Unifying receiver,
remove the last difference by dropping the product ID as devices
usually have different product IDs when connected through USB or
Unifying.
For example, on the serials on a G903 wired/wireless mouse:
- Unifying before patch: 4067-e8-ce-cd-45
- USB before patch: c086-e8-ce-cd-45
- Unifying and USB after patch: e8-ce-cd-45
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20230302130117.3975-2-hadess@hadess.net
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ad1fe0da0 ]
For devices that support the 0x0003 feature (Device Information) version 4,
set the serial based on the output of that feature, rather than relying
on the usbhid code setting the USB serial.
This should allow the serial when connected through USB to (nearly)
match the one when connected through a unifying receiver.
For example, on the serials on a G903 wired/wireless mouse:
- Unifying: 4067-e8-ce-cd-45
- USB before patch: 017C385C3837
- USB after patch: c086-e8-ce-cd-45
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20230302130117.3975-1-hadess@hadess.net
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 752cbd8f19 ]
Initialize the module parameters, read_timeout and write_timeout once in
init().
Module parameters can only be set once and cannot be modified later, so we
don't need to evaluate them again when passing the parameters to
wait_event_interruptible_timeout().
Convert datatype of {read,write}_timeout from 'int' to 'long int' because
implicit conversion of 'long int' to 'int' in statement
'{read,write}_timeout = MAX_SCHEDULE_TIMEOUT' results in an overflow.
Change format specifier for {read,write}_timeout from %i to %li.
Reviewed-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Khadija Kamran <kamrankhadijadj@gmail.com>
Link: https://lore.kernel.org/r/ZBN3XAsItCiTk7CV@khadija-virtual-machine
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db3c490503 ]
During digital filters settling time the driver is expected to drop
samples since they can be corrupted. Introduce the capability to drop
a given number of samples according to the configured ODR.
Add sample_to_discard for LSM6DSM-like sensors since new generation
devices (e.g. LSM6DSO) support DRDY mask where corrupted samples are
masked in hw with values greather than 0x7ffd so the driver can easily
discard them.
I have not added sample_to_discard support for LSM6DS3 or LSM6DS3H since
I do not have any sample for testing at the moment.
Reported-by: Philippe De Muyter <phdm@macqel.be>
Tested-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/21dcd94935c147ef9b1da4984b3da6264ee9609e.1677496295.git.lorenzo@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3388ddc74 ]
I recently tested several old MacBooks and as far as I can tell, all
MacBooks that have an ISO keyboard have the tilde key quirk:
Product Model Year System CPU Shape Labels Country Quirky
============================================================================
05ac:021b A1181 2006 MacBook2,1 T5600 ISO British 13 Yes
05ac:021b A1181 2007 MacBook2,1 T7200 ISO Québécois 13 Yes
05ac:0229 A1181 2007 MacBook4,1 T8300 ANSI Usonian 33 No
05ac:022a A1181 2007 MacBook4,1 T8100 ISO English 13 Yes
05ac:022a A1181 2007 MacBook5,2 P7350 ISO Québécois 13 Yes
05ac:0237 A1278 2008 MacBook5,1 P7350 ISO Dutch 13 Yes
05ac:0237 A1278 2009 MacBook5,5 P7550 ISO British 13 Yes
The model number and year are from the laptop case. Since Apple printed
the same model and year on many different laptops, the system name (as
reported in the SMBIOS tables) and CPU form a more precise identifier.
Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91b6d02ddc ]
The ATS2851 based controller advertises support for command "LE Set Random
Private Address Timeout" but does not actually implement it, impeding the
controller initialization.
Add the quirk HCI_QUIRK_BROKEN_SET_RPA_TIMEOUT to unblock the controller
initialization.
< HCI Command: LE Set Resolvable Private... (0x08|0x002e) plen 2
Timeout: 900 seconds
> HCI Event: Command Status (0x0f) plen 4
LE Set Resolvable Private Address Timeout (0x08|0x002e) ncmd 1
Status: Unknown HCI Command (0x01)
Co-developed-by: imoc <wzj9912@gmail.com>
Signed-off-by: imoc <wzj9912@gmail.com>
Signed-off-by: Raul Cheleguini <raul.cheleguini@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d218c3642 ]
On some devices the BCM Bluetooth adapter does not have a valid bdaddr set.
btbcm.c currently sets HCI_QUIRK_INVALID_BDADDR to indicate when this is
the case. But this requires users to manual setup a btaddr, by doing e.g.:
btmgmt -i hci0 public-addr 'B0:F1:EC:82:1D:B3'
Which means that Bluetooth will not work out of the box on such devices.
To avoid this (where possible) hci_bcm sets: HCI_QUIRK_USE_BDADDR_PROPERTY
which tries to get the bdaddr from devicetree.
But this only works on devicetree platforms. On UEFI based platforms
there is a special Broadcom UEFI variable which when present contains
the devices bdaddr, just like how there is another UEFI variable which
contains wifi nvram contents including the wifi MAC address.
Add support for getting the bdaddr from this Broadcom UEFI variable,
so that Bluetooth will work OOTB for users on devices where this
UEFI variable is present.
This fixes Bluetooth not working on for example Asus T100HA 2-in-1s.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77f542b10c ]
Basically all Intel controllers support both Central/Peripheral
LE states.
This patch enables the LE States quirk by default on all
Solar and Magnertor Intel controllers.
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 253cf30e8d ]
The btrtl_set_quirks() has accessed btrtl_dev->ic_info->lmp_subver since
b8e482d02513. However, if installing a Realtek Bluetooth controller
without the driver supported, it will hit the NULL point accessed.
Add a check for NULL to avoid the Kernel Oops.
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c2b2d2d0c ]
Add two more quirks to resume the device initialization and basic
operation as the device seems not to support "Read Transmit Power"
and "Set Extended Scan Parameters".
< HCI Command: LE Read Transmit Power (0x08|0x004b) plen 0
> HCI Event: Command Status (0x0f) plen 4
LE Read Transmit Power (0x08|0x004b) ncmd 1
Status: Unknown HCI Command (0x01)
< HCI Command: LE Set Extended Scan Parameters (0x08|0x0041) plen 8
Own address type: Random (0x01)
Filter policy: Accept all advertisement (0x00)
PHYs: 0x01
Entry 0: LE 1M
Type: Active (0x01)
Interval: 11.250 msec (0x0012)
Window: 11.250 msec (0x0012)
> HCI Event: Command Status (0x0f) plen 4
LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1
Status: Unknown HCI Command (0x01)
Signed-off-by: Raul Cheleguini <rcheleguini@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0123cb6c4 ]
The Realtek RTL8723CS is a SDIO WiFi chip. It also contains a Bluetooth
module which is connected via UART to the host.
It shares lmp subversion with 8703B, so Realtek's userspace
initialization tool (rtk_hciattach) differentiates varieties of RTL8723CS
(CG, VF, XX) with RTL8703B using vendor's command to read chip type.
Also this chip declares support for some features it doesn't support
so add a quirk to indicate that these features are broken.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Bastian Germann <bage@debian.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8194f1ef5a ]
Some adapters (e.g. RTL8723CS) advertise that they have more than
2 pages for local ext features, but they don't support any features
declared in these pages. RTL8723CS reports max_page = 2 and declares
support for sync train and secure connection, but it responds with
either garbage or with error in status on corresponding commands.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Bastian Germann <bage@debian.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3478c68f6 ]
In ip_vs_sync_conn_v0() copy is made to struct ip_vs_sync_conn_options.
That structure looks like this:
struct ip_vs_sync_conn_options {
struct ip_vs_seq in_seq;
struct ip_vs_seq out_seq;
};
The source of the copy is the in_seq field of struct ip_vs_conn. Whose
type is struct ip_vs_seq. Thus we can see that the source - is not as
wide as the amount of data copied, which is the width of struct
ip_vs_sync_conn_option.
The copy is safe because the next field in is another struct ip_vs_seq.
Make use of struct_group() to annotate this.
Flagged by gcc-13 as:
In file included from ./include/linux/string.h:254,
from ./include/linux/bitmap.h:11,
from ./include/linux/cpumask.h:12,
from ./arch/x86/include/asm/paravirt.h:17,
from ./arch/x86/include/asm/cpuid.h:62,
from ./arch/x86/include/asm/processor.h:19,
from ./arch/x86/include/asm/timex.h:5,
from ./include/linux/timex.h:67,
from ./include/linux/time32.h:13,
from ./include/linux/time.h:60,
from ./include/linux/stat.h:19,
from ./include/linux/module.h:13,
from net/netfilter/ipvs/ip_vs_sync.c:38:
In function 'fortify_memcpy_chk',
inlined from 'ip_vs_sync_conn_v0' at net/netfilter/ipvs/ip_vs_sync.c:606:3:
./include/linux/fortify-string.h:529:25: error: call to '__read_overflow2_field' declared with attribute warning: detected read beyond size of field (2nd parameter); maybe use struct_group()? [-Werror=attribute-warning]
529 | __read_overflow2_field(q_size_field, size);
|
Compile tested only.
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55793ea54d ]
We tested and found an alarm caused by nbd_ioctl arg without verification.
The UBSAN warning calltrace like below:
UBSAN: Undefined behaviour in fs/buffer.c:1709:35
signed integer overflow:
-9223372036854775808 - 1 cannot be represented in type 'long long int'
CPU: 3 PID: 2523 Comm: syz-executor.0 Not tainted 4.19.90 #1
Hardware name: linux,dummy-virt (DT)
Call trace:
dump_backtrace+0x0/0x3f0 arch/arm64/kernel/time.c:78
show_stack+0x28/0x38 arch/arm64/kernel/traps.c:158
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x170/0x1dc lib/dump_stack.c:118
ubsan_epilogue+0x18/0xb4 lib/ubsan.c:161
handle_overflow+0x188/0x1dc lib/ubsan.c:192
__ubsan_handle_sub_overflow+0x34/0x44 lib/ubsan.c:206
__block_write_full_page+0x94c/0xa20 fs/buffer.c:1709
block_write_full_page+0x1f0/0x280 fs/buffer.c:2934
blkdev_writepage+0x34/0x40 fs/block_dev.c:607
__writepage+0x68/0xe8 mm/page-writeback.c:2305
write_cache_pages+0x44c/0xc70 mm/page-writeback.c:2240
generic_writepages+0xdc/0x148 mm/page-writeback.c:2329
blkdev_writepages+0x2c/0x38 fs/block_dev.c:2114
do_writepages+0xd4/0x250 mm/page-writeback.c:2344
The reason for triggering this warning is __block_write_full_page()
-> i_size_read(inode) - 1 overflow.
inode->i_size is assigned in __nbd_ioctl() -> nbd_set_size() -> bytesize.
We think it is necessary to limit the size of arg to prevent errors.
Moreover, __nbd_ioctl() -> nbd_add_socket(), arg will be cast to int.
Assuming the value of arg is 0x80000000000000001) (on a 64-bit machine),
it will become 1 after the coercion, which will return unexpected results.
Fix it by adding checks to prevent passing in too large numbers.
Signed-off-by: Zhong Jinghua <zhongjinghua@huawei.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Link: https://lore.kernel.org/r/20230206145805.2645671-1-zhongjinghua@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9fff67d2d ]
While running traffics for a long time, randomly an RX descriptor
filled with value "0" from REO destination ring is received.
This descriptor which is invalid causes the wrong SKB (SKB stored in
the IDR lookup with buffer id "0") to be fetched which in turn
causes SKB memory corruption issue and the same leads to crash
after some time.
Changed the start id for idr allocation to "1" and the buffer id "0"
is reserved for error validation. Introduced Sanity check to validate
the descriptor, before processing the SKB.
Crash Signature :
Unable to handle kernel paging request at virtual address 3f004900
PC points to "b15_dma_inv_range+0x30/0x50"
LR points to "dma_cache_maint_page+0x8c/0x128".
The Backtrace obtained is as follows:
[<8031716c>] (b15_dma_inv_range) from [<80313a4c>] (dma_cache_maint_page+0x8c/0x128)
[<80313a4c>] (dma_cache_maint_page) from [<80313b90>] (__dma_page_dev_to_cpu+0x28/0xcc)
[<80313b90>] (__dma_page_dev_to_cpu) from [<7fb5dd68>] (ath11k_dp_process_rx+0x1e8/0x4a4 [ath11k])
[<7fb5dd68>] (ath11k_dp_process_rx [ath11k]) from [<7fb53c20>] (ath11k_dp_service_srng+0xb0/0x2ac [ath11k])
[<7fb53c20>] (ath11k_dp_service_srng [ath11k]) from [<7f67bba4>] (ath11k_pci_ext_grp_napi_poll+0x1c/0x78 [ath11k_pci])
[<7f67bba4>] (ath11k_pci_ext_grp_napi_poll [ath11k_pci]) from [<807d5cf4>] (__napi_poll+0x28/0xb8)
[<807d5cf4>] (__napi_poll) from [<807d5f28>] (net_rx_action+0xf0/0x280)
[<807d5f28>] (net_rx_action) from [<80302148>] (__do_softirq+0xd0/0x280)
[<80302148>] (__do_softirq) from [<80320408>] (irq_exit+0x74/0xd4)
[<80320408>] (irq_exit) from [<803638a4>] (__handle_domain_irq+0x90/0xb4)
[<803638a4>] (__handle_domain_irq) from [<805bedec>] (gic_handle_irq+0x58/0x90)
[<805bedec>] (gic_handle_irq) from [<80301a78>] (__irq_svc+0x58/0x8c)
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Nagarajan Maran <quic_nmaran@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230403191533.28114-1-quic_nmaran@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef16799640 ]
A received TKIP key may be up to 32 bytes because it may contain
MIC rx/tx keys too. These are not used by iwl and copying these
over overflows the iwl_keyinfo.key field.
Add a check to not copy more data to iwl_keyinfo.key then will fit.
This fixes backtraces like this one:
memcpy: detected field-spanning write (size 32) of single field "sta_cmd.key.key" at drivers/net/wireless/intel/iwlwifi/dvm/sta.c:1103 (size 16)
WARNING: CPU: 1 PID: 946 at drivers/net/wireless/intel/iwlwifi/dvm/sta.c:1103 iwlagn_send_sta_key+0x375/0x390 [iwldvm]
<snip>
Hardware name: Dell Inc. Latitude E6430/0H3MT5, BIOS A21 05/08/2017
RIP: 0010:iwlagn_send_sta_key+0x375/0x390 [iwldvm]
<snip>
Call Trace:
<TASK>
iwl_set_dynamic_key+0x1f0/0x220 [iwldvm]
iwlagn_mac_set_key+0x1e4/0x280 [iwldvm]
drv_set_key+0xa4/0x1b0 [mac80211]
ieee80211_key_enable_hw_accel+0xa8/0x2d0 [mac80211]
ieee80211_key_replace+0x22d/0x8e0 [mac80211]
<snip>
Link: https://www.alionet.org/index.php?topic=1469.0
Link: https://lore.kernel.org/linux-wireless/20230218191056.never.374-kees@kernel.org/
Link: https://lore.kernel.org/linux-wireless/68760035-7f75-1b23-e355-bfb758a87d83@redhat.com/
Cc: Kees Cook <keescook@chromium.org>
Suggested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03eb52dd78 ]
Issue: Though the Netgear AXE3000 (A8000) is based on the mt7921
chipset because of the unique USB VID:PID combination this device
does not initialize/register. Thus making it not plug and play.
Fix: Adds support for the Netgear AXE3000 (A8000) based on the Mediatek
mt7921au chipset. The method of action is adding the USD VID/PID
pair to the mt7921u_device_table[] array.
Notes: A retail sample of the Netgear AXE3000 (A8000) yeilds the following
from lsusb D 0846:9060 NetGear, Inc. Wireless_Device. This pair
0846:9060 VID:PID has been reported by other users on Github.
Signed-off-by: Reese Russell <git@qrsnap.io>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a06bfb3c9f ]
When max virtual ap interfaces are configured in all the bands with
ACS and hostapd restart is done every 60s, a crash is observed at
random times.
In this certain scenario, a fragmented packet is received for
self peer, for which rx_tid and rx_frags are not initialized in
datapath. While handling this fragment, crash is observed as the
rx_frag list is uninitialised and when we walk in
ath11k_dp_rx_h_sort_frags, skb null leads to exception.
To address this, before processing received fragments we check
dp_setup_done flag is set to ensure that peer has completed its
dp peer setup for fragment queue, else ignore processing the
fragments.
Call trace:
ath11k_dp_process_rx_err+0x550/0x1084 [ath11k]
ath11k_dp_service_srng+0x70/0x370 [ath11k]
0xffffffc009693a04
__napi_poll+0x30/0xa4
net_rx_action+0x118/0x270
__do_softirq+0x10c/0x244
irq_exit+0x64/0xb4
__handle_domain_irq+0x88/0xac
gic_handle_irq+0x74/0xbc
el1_irq+0xf0/0x1c0
arch_cpu_idle+0x10/0x18
do_idle+0x104/0x248
cpu_startup_entry+0x20/0x64
rest_init+0xd0/0xdc
arch_call_rest_init+0xc/0x14
start_kernel+0x480/0x4b8
Code: f9400281 f94066a2 91405021 b94a0023 (f9406401)
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Nagarajan Maran <quic_nmaran@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230403184155.8670-2-quic_nmaran@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58d1b71787 ]
An integer overflow occurs in the iwl_write_to_user_buf() function,
which is called by the iwl_dbgfs_monitor_data_read() function.
static bool iwl_write_to_user_buf(char __user *user_buf, ssize_t count,
void *buf, ssize_t *size,
ssize_t *bytes_copied)
{
int buf_size_left = count - *bytes_copied;
buf_size_left = buf_size_left - (buf_size_left % sizeof(u32));
if (*size > buf_size_left)
*size = buf_size_left;
If the user passes a SIZE_MAX value to the "ssize_t count" parameter,
the ssize_t count parameter is assigned to "int buf_size_left".
Then compare "*size" with "buf_size_left" . Here, "buf_size_left" is a
negative number, so "*size" is assigned "buf_size_left" and goes into
the third argument of the copy_to_user function, causing a heap overflow.
This is not a security vulnerability because iwl_dbgfs_monitor_data_read()
is a debugfs operation with 0400 privileges.
Signed-off-by: Hyunwoo Kim <imv4bel@gmail.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230414130637.2d80ace81532.Iecfba549e0e0be21bbb0324675392e42e75bd5ad@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b655b9a9f8 ]
It is possible that iwl_pci_probe() will fail and free the trans,
then afterwards iwl_pci_remove() will be called and crash by trying
to access trans which is already freed, fix it.
iwlwifi 0000:01:00.0: Detected crf-id 0xa5a5a5a2, cnv-id 0xa5a5a5a2
wfpm id 0xa5a5a5a2
iwlwifi 0000:01:00.0: Can't find a correct rfid for crf id 0x5a2
...
BUG: kernel NULL pointer dereference, address: 0000000000000028
...
RIP: 0010:iwl_pci_remove+0x12/0x30 [iwlwifi]
pci_device_remove+0x3e/0xb0
device_release_driver_internal+0x103/0x1f0
driver_detach+0x4c/0x90
bus_remove_driver+0x5c/0xd0
driver_unregister+0x31/0x50
pci_unregister_driver+0x40/0x90
iwl_pci_unregister_driver+0x15/0x20 [iwlwifi]
__exit_compat+0x9/0x98 [iwlwifi]
__x64_sys_delete_module+0x147/0x260
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413213309.082f6e21341b.I0db21d7fa9a828d571ca886713bd0b5d0b6e1e5c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c54876cd59 ]
With the multiplexed ndo_setup_tc() model which lacks a first-class
struct netlink_ext_ack * argument, the only way to pass the netlink
extended ACK message down to the device driver is to embed it within the
offload structure.
Do this for struct tc_mqprio_qopt_offload and struct tc_taprio_qopt_offload.
Since struct tc_taprio_qopt_offload also contains a tc_mqprio_qopt_offload
structure, and since device drivers might effectively reuse their mqprio
implementation for the mqprio portion of taprio, we make taprio set the
extack in both offload structures to point at the same netlink extack
message.
In fact, the taprio handling is a bit more tricky, for 2 reasons.
First is because the offload structure has a longer lifetime than the
extack structure. The driver is supposed to populate the extack
synchronously from ndo_setup_tc() and leave it alone afterwards.
To not have any use-after-free surprises, we zero out the extack pointer
when we leave taprio_enable_offload().
The second reason is because taprio does overwrite the extack message on
ndo_setup_tc() error. We need to switch to the weak form of setting an
extack message, which preserves a potential message set by the driver.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6efddf1e32 ]
status_resync() will calculate 'curr_resync - recovery_active' to show
user a progress bar like following:
[============>........] resync = 61.4%
'curr_resync' and 'recovery_active' is updated in md_do_sync(), and
status_resync() can read them concurrently, hence it's possible that
'curr_resync - recovery_active' can overflow to a huge number. In this
case status_resync() will be stuck in the loop to print a large amount
of '=', which will end up soft lockup.
Fix the problem by setting 'resync' to MD_RESYNC_ACTIVE in this case,
this way resync in progress will be reported to user.
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230310073855.1337560-3-yukuai1@huaweicloud.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c11bd04648 ]
The recursion check in __bpf_prog_enter* and __bpf_prog_exit*
leave preempt_count_{sub,add} unprotected. When attaching trampoline to
them we get panic as follows,
[ 867.843050] BUG: TASK stack guard page was hit at 0000000009d325cf (stack is 0000000046a46a15..00000000537e7b28)
[ 867.843064] stack guard page: 0000 [#1] PREEMPT SMP NOPTI
[ 867.843067] CPU: 8 PID: 11009 Comm: trace Kdump: loaded Not tainted 6.2.0+ #4
[ 867.843100] Call Trace:
[ 867.843101] <TASK>
[ 867.843104] asm_exc_int3+0x3a/0x40
[ 867.843108] RIP: 0010:preempt_count_sub+0x1/0xa0
[ 867.843135] __bpf_prog_enter_recur+0x17/0x90
[ 867.843148] bpf_trampoline_6442468108_0+0x2e/0x1000
[ 867.843154] ? preempt_count_sub+0x1/0xa0
[ 867.843157] preempt_count_sub+0x5/0xa0
[ 867.843159] ? migrate_enable+0xac/0xf0
[ 867.843164] __bpf_prog_exit_recur+0x2d/0x40
[ 867.843168] bpf_trampoline_6442468108_0+0x55/0x1000
...
[ 867.843788] preempt_count_sub+0x5/0xa0
[ 867.843793] ? migrate_enable+0xac/0xf0
[ 867.843829] __bpf_prog_exit_recur+0x2d/0x40
[ 867.843837] BUG: IRQ stack guard page was hit at 0000000099bd8228 (stack is 00000000b23e2bc4..000000006d95af35)
[ 867.843841] BUG: IRQ stack guard page was hit at 000000005ae07924 (stack is 00000000ffd69623..0000000014eb594c)
[ 867.843843] BUG: IRQ stack guard page was hit at 00000000028320f0 (stack is 00000000034b6438..0000000078d1bcec)
[ 867.843842] bpf_trampoline_6442468108_0+0x55/0x1000
...
That is because in __bpf_prog_exit_recur, the preempt_count_{sub,add} are
called after prog->active is decreased.
Fixing this by adding these two functions into btf ids deny list.
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Yafang <laoar.shao@gmail.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Jiri Olsa <olsajiri@gmail.com>
Acked-by: Hao Luo <haoluo@google.com>
Link: https://lore.kernel.org/r/20230413025248.79764-1-laoar.shao@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d78dfefcde ]
With below case, it can mount multi-device image w/ rw option, however
one of secondary device is set as ro, later update will cause panic, so
let's introduce f2fs_dev_is_readonly(), and check multi-devices rw status
in f2fs_remount() w/ it in order to avoid such inconsistent mount status.
mkfs.f2fs -c /dev/zram1 /dev/zram0 -f
blockdev --setro /dev/zram1
mount -t f2fs dev/zram0 /mnt/f2fs
mount: /mnt/f2fs: WARNING: source write-protected, mounted read-only.
mount -t f2fs -o remount,rw mnt/f2fs
dd if=/dev/zero of=/mnt/f2fs/file bs=1M count=8192
kernel BUG at fs/f2fs/inline.c:258!
RIP: 0010:f2fs_write_inline_data+0x23e/0x2d0 [f2fs]
Call Trace:
f2fs_write_single_data_page+0x26b/0x9f0 [f2fs]
f2fs_write_cache_pages+0x389/0xa60 [f2fs]
__f2fs_write_data_pages+0x26b/0x2d0 [f2fs]
f2fs_write_data_pages+0x2e/0x40 [f2fs]
do_writepages+0xd3/0x1b0
__writeback_single_inode+0x5b/0x420
writeback_sb_inodes+0x236/0x5a0
__writeback_inodes_wb+0x56/0xf0
wb_writeback+0x2a3/0x490
wb_do_writeback+0x2b2/0x330
wb_workfn+0x6a/0x260
process_one_work+0x270/0x5e0
worker_thread+0x52/0x3e0
kthread+0xf4/0x120
ret_from_fork+0x29/0x50
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9b3649a93 ]
xfstest generic/361 reports a bug as below:
f2fs_bug_on(sbi, sbi->fsync_node_num);
kernel BUG at fs/f2fs/super.c:1627!
RIP: 0010:f2fs_put_super+0x3a8/0x3b0
Call Trace:
generic_shutdown_super+0x8c/0x1b0
kill_block_super+0x2b/0x60
kill_f2fs_super+0x87/0x110
deactivate_locked_super+0x39/0x80
deactivate_super+0x46/0x50
cleanup_mnt+0x109/0x170
__cleanup_mnt+0x16/0x20
task_work_run+0x65/0xa0
exit_to_user_mode_prepare+0x175/0x190
syscall_exit_to_user_mode+0x25/0x50
do_syscall_64+0x4c/0x90
entry_SYSCALL_64_after_hwframe+0x72/0xdc
During umount(), if cp_error is set, f2fs_wait_on_all_pages() should
not stop waiting all F2FS_WB_CP_DATA pages to be writebacked, otherwise,
fsync_node_num can be non-zero after f2fs_wait_on_all_pages() causing
this bug.
In this case, to avoid deadloop in f2fs_wait_on_all_pages(), it needs
to drop all dirty pages rather than redirtying them.
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3fde2fe99a ]
According to SP800-90B, two health failures are allowed: the intermittend
and the permanent failure. So far, only the intermittent failure was
implemented. The permanent failure was achieved by resetting the entire
entropy source including its health test state and waiting for two or
more back-to-back health errors.
This approach is appropriate for RCT, but not for APT as APT has a
non-linear cutoff value. Thus, this patch implements 2 cutoff values
for both RCT/APT. This implies that the health state is left untouched
when an intermittent failure occurs. The noise source is reset
and a new APT powerup-self test is performed. Yet, whith the unchanged
health test state, the counting of failures continues until a permanent
failure is reached.
Any non-failing raw entropy value causes the health tests to reset.
The intermittent error has an unchanged significance level of 2^-30.
The permanent error has a significance level of 2^-60. Considering that
this level also indicates a false-positive rate (see SP800-90B section 4.2)
a false-positive must only be incurred with a low probability when
considering a fleet of Linux kernels as a whole. Hitting the permanent
error may cause a panic(), the following calculation applies: Assuming
that a fleet of 10^9 Linux kernels run concurrently with this patch in
FIPS mode and on each kernel 2 health tests are performed every minute
for one year, the chances of a false positive is about 1:1000
based on the binomial distribution.
In addition, any power-up health test errors triggered with
jent_entropy_init are treated as permanent errors.
A permanent failure causes the entire entropy source to permanently
return an error. This implies that a caller can only remedy the situation
by re-allocating a new instance of the Jitter RNG. In a subsequent
patch, a transparent re-allocation will be provided which also changes
the implied heuristic entropy assessment.
In addition, when the kernel is booted with fips=1, the Jitter RNG
is defined to be part of a FIPS module. The permanent error of the
Jitter RNG is translated as a FIPS module error. In this case, the entire
FIPS module must cease operation. This is implemented in the kernel by
invoking panic().
The patch also fixes an off-by-one in the RCT cutoff value which is now
set to 30 instead of 31. This is because the counting of the values
starts with 0.
Reviewed-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Reviewed-by: Marcelo Henrique Cerri <marcelo.cerri@canonical.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93cdf49f6e ]
When the length of best extent found is less than the length of goal extent
we need to make sure that the best extent atleast covers the start of the
original request. This is done by adjusting the ac_b_ex.fe_logical (logical
start) of the extent.
While doing so, the current logic sometimes results in the best extent's
logical range overflowing the goal extent. Since this best extent is later
added to the inode preallocation list, we have a possibility of introducing
overlapping preallocations. This is discussed in detail here [1].
As per Jan's suggestion, to fix this, replace the existing logic with the
below logic for adjusting best extent as it keeps fragmentation in check
while ensuring logical range of best extent doesn't overflow out of goal
extent:
1. Check if best extent can be kept at end of goal range and still cover
original start.
2. Else, check if best extent can be kept at start of goal range and still
cover original start.
3. Else, keep the best extent at start of original request.
Also, add a few extra BUG_ONs that might help catch errors faster.
[1] https://lore.kernel.org/r/Y+OGkVvzPN0RMv0O@li-bb2b2a4c-3307-11b2-a85c-8fa5c3a69313.ibm.com
Suggested-by: Jan Kara <jack@suse.cz>
Signed-off-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Reviewed-by: Ritesh Harjani (IBM) <ritesh.list@gmail.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/f96aca6d415b36d1f90db86c1a8cd7e2e9d7ab0e.1679731817.git.ojaswin@linux.ibm.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b07ffe6927 ]
We need to set ac_g_ex to notify the goal start used in
ext4_mb_find_by_goal. Set ac_g_ex instead of ac_f_ex in
ext4_mb_normalize_request.
Besides we should assure goal start is in range [first_data_block,
blocks_count) as ext4_mb_initialize_context does.
[ Added a check to make sure size is less than ar->pright; otherwise
we could end up passing an underflowed value of ar->pright - size to
ext4_get_group_no_and_offset(), which will trigger a BUG_ON later on.
- TYT ]
Signed-off-by: Kemeng Shi <shikemeng@huaweicloud.com>
Reviewed-by: Ritesh Harjani (IBM) <ritesh.list@gmail.com>
Link: https://lore.kernel.org/r/20230303172120.3800725-2-shikemeng@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cfcdb5bad3 ]
The maximum allowed height of an inode's metadata tree depends on the
filesystem block size; it is lower for bigger-block filesystems. When
reading in an inode, make sure that the height doesn't exceed the
maximum allowed height.
Arrays like sd_heightsize are sized to be big enough for any filesystem
block size; they will often be slightly bigger than what's needed for a
specific filesystem.
Reported-by: syzbot+45d4691b1ed3c48eba05@syzkaller.appspotmail.com
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f486893288 ]
mptlan_probe() calls mpt_register_lan_device() which initializes the
&priv->post_buckets_task workqueue. A call to
mpt_lan_wake_post_buckets_task() will subsequently start the work.
During driver unload in mptlan_remove() the following race may occur:
CPU0 CPU1
|mpt_lan_post_receive_buckets_work()
mptlan_remove() |
free_netdev() |
kfree(dev); |
|
| dev->mtu
| //use
Fix this by finishing the work prior to cleaning up in mptlan_remove().
[mkp: we really should remove mptlan instead of attempting to fix it]
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Link: https://lore.kernel.org/r/20230318081635.796479-1-zyytlz.wz@163.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e0473f106 ]
When calling irq_set_affinity_notifier() with NULL at the notify
argument, it will cause freeing of the glue pointer in the
corresponding array entry but will leave the pointer in the array. A
subsequent call to free_irq_cpu_rmap() will try to free this entry again
leading to possible use after free.
Fix that by setting NULL to the array entry and checking that we have
non-zero at the array entry when iterating over the array in
free_irq_cpu_rmap().
The current code does not suffer from this since there are no cases
where irq_set_affinity_notifier(irq, NULL) (note the NULL passed for the
notify arg) is called, followed by a call to free_irq_cpu_rmap() so we
don't hit and issue. Subsequent patches in this series excersize this
flow, hence the required fix.
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8990b5a4d ]
Commands from recovery entries are freed after session has been closed.
That leads to use-after-free at command free or NPE with such call trace:
Time2Retain timer expired for SID: 1, cleaning up iSCSI session.
BUG: kernel NULL pointer dereference, address: 0000000000000140
RIP: 0010:sbitmap_queue_clear+0x3a/0xa0
Call Trace:
target_release_cmd_kref+0xd1/0x1f0 [target_core_mod]
transport_generic_free_cmd+0xd1/0x180 [target_core_mod]
iscsit_free_cmd+0x53/0xd0 [iscsi_target_mod]
iscsit_free_connection_recovery_entries+0x29d/0x320 [iscsi_target_mod]
iscsit_close_session+0x13a/0x140 [iscsi_target_mod]
iscsit_check_post_dataout+0x440/0x440 [iscsi_target_mod]
call_timer_fn+0x24/0x140
Move cleanup of recovery enrties to before session freeing.
Reported-by: Forza <forza@tnonline.net>
Signed-off-by: Dmitry Bogdanov <d.bogdanov@yadro.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20230319015620.96006-7-michael.christie@oracle.com
Reviewed-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1cc6571f56 ]
When requesting a TX queue at a given index, warn on out-of-bounds
referencing if the index is greater than the allocated number of
queues.
Specifically, since this function is used heavily in the networking
stack use DEBUG_NET_WARN_ON_ONCE to avoid executing a new branch on
every packet.
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Link: https://lore.kernel.org/r/20230321150725.127229-2-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5dd0dfd55b ]
When setting the XPS value of a TX queue, warn the user once if the
index of the queue is greater than the number of allocated TX queues.
Previously, this scenario went uncaught. In the best case, it resulted
in unnecessary allocations. In the worst case, it resulted in
out-of-bounds memory references through calls to `netdev_get_tx_queue(
dev, index)`. Therefore, it is important to inform the user but not
worth returning an error and risk downing the netdevice.
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Link: https://lore.kernel.org/r/20230321150725.127229-1-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8384d4a51 ]
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed. A
warning in clang aims to catch these at compile time, which reveals:
drivers/net/ethernet/pasemi/pasemi_mac.c:1665:21: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.ndo_start_xmit = pasemi_mac_start_tx,
^~~~~~~~~~~~~~~~~~~
1 error generated.
->ndo_start_xmit() in 'struct net_device_ops' expects a return type of
'netdev_tx_t', not 'int'. Adjust the return type of
pasemi_mac_start_tx() to match the prototype's to resolve the warning.
While PowerPC does not currently implement support for kCFI, it could in
the future, which means this warning becomes a fatal CFI failure at run
time.
Link: https://github.com/ClangBuiltLinux/linux/issues/1750
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20230319-pasemi-incompatible-pointer-types-strict-v1-1-1b9459d8aef0@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db651ec225 ]
A fabric controller can sometimes send an RDP request right before a link
down event. Because of this outstanding RDP request, the driver does not
remove the last reference count on its ndlp causing a potential leak of RPI
resources when devloss tmo fires.
In lpfc_cmpl_els_rsp(), modify the NPIV clause to always allow the
lpfc_drop_node() routine to execute when not registered with SCSI
transport.
This relaxes the contraint that an NPIV ndlp must be in a specific state in
order to call lpfc_drop node. Logic is revised such that the
lpfc_drop_node() routine is always called to ensure the last ndlp decrement
occurs.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20230301231626.9621-7-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c6087b82a9 ]
A static code analysis tool flagged the possibility of buffer overflow when
using copy_from_user() for a debugfs entry.
Currently, it is possible that copy_from_user() copies more bytes than what
would fit in the mybuf char array. Add a min() restriction check between
sizeof(mybuf) - 1 and nbytes passed from the userspace buffer to protect
against buffer overflow.
Link: https://lore.kernel.org/r/20230301231626.9621-2-justintee8345@gmail.com
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89b89e5215 ]
Apparently the hex passphrase mechanism does not work on newer
chips/firmware (e.g. BCM4387). It seems there was a simple way of
passing it in binary all along, so use that and avoid the hexification.
OpenBSD has been doing it like this from the beginning, so this should
work on all chips.
Also clear the structure before setting the PMK. This was leaking
uninitialized stack contents to the device.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230214092423.15175-6-marcan@marcan.st
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91918ce88d ]
Newer Apple firmwares on chipsets without a hardware RNG require the
host to provide a buffer of 256 random bytes to the device on
initialization. This buffer is present immediately before NVRAM,
suffixed by a footer containing a magic number and the buffer length.
This won't affect chips/firmwares that do not use this feature, so do it
unconditionally for all Apple platforms (those with an Apple OTP).
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230214080034.3828-3-marcan@marcan.st
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a09a2f933 ]
There are a few cases where hlist_node is checked to be unhashed without
holding the lock protecting its modification. In this case, one must use
hlist_unhashed_lockless to avoid load tearing and KCSAN reports. Fix
this by using lockless variant in places not protected by the lock.
Since this is not prompted by any actual KCSAN reports but only from
code review, I have not included a fixes tag.
Cc: Martin KaFai Lau <martin.lau@kernel.org>
Cc: KP Singh <kpsingh@kernel.org>
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/r/20230221200646.2500777-4-memxor@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8fbcf730cb ]
variable *nplanes is provided by user via system call argument. The
possible value of q_data->fmt->num_planes is 1-3, while the value
of *nplanes can be 1-8. The array access by index i can cause array
out-of-bounds.
Fix this bug by checking *nplanes against the array size.
Signed-off-by: Wei Chen <harperchen1110@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 318e431b30 ]
This patch enables the IH retry CAM on GFX9 series cards. This
retry filter is used to prevent sending lots of retry interrupts
in a short span of time and overflowing the IH ring buffer. This
will also help reduce CPU interrupt workload.
Signed-off-by: Mukul Joshi <mukul.joshi@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3a69496a1 ]
Structures passed to subdev pad operations are all zero-initialized, but
not always with the same kind of code constructs. While most drivers
used designated initializers, which zero all the fields that are not
specified, when declaring variables, some use memset(). Those two
methods lead to the same end result, and, depending on compiler
optimizations, may even be completely equivalent, but they're not
consistent.
Improve coding style consistency by using designated initializers
instead of calling memset(). Where applicable, also move the variables
to inner scopes of for loops to ensure correct initialization in all
iterations.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Lad Prabhakar <prabhakar.csengg@gmail.com> # For am437x
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 385c3e4c29 ]
[Why]
In 2560x1600@240p eDP panel, driver use lowest voltage level
to play 1080p video cause underflow. According to HW SPEC,
the senario should use high voltage level.
[How]
ChromaPre value is zero when bandwidth validation.
Correct ChromaPre calculation.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Paul Hsieh <Paul.Hsieh@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit abe4f5ae5e ]
After the recent backlight changes acpi_video# backlight devices are only
registered when explicitly requested from the cmdline, by DMI quirk or by
the GPU driver.
This means that we no longer get false-positive backlight control support
advertised on desktop boards.
Remove the 3 DMI quirks for desktop boards where the false-positive issue
was fixed through quirks before. Note many more desktop boards were
affected but we never build a full quirk list for this.
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 567f97bd38 ]
In current cio2-bridge, it is using the hid name to register software
node and software node will create kobject and sysfs entry according to
the node name, if there are multiple sensors and VCMs which are sharing
same HID name, it will cause the software nodes registration failure:
sysfs: cannot create duplicate filename '/kernel/software_nodes/dw9714'
...
Call Trace:
software_node_register_nodes
cio2_bridge_init
...
kobject_add_internal failed for dw9714 with -EEXIST,
don't try to register things with the same name in the same directory.
One solution is appending the sensor link(Mipi Port) in SSDB as suffix
of the node name to fix this problem.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35727af2b1 ]
The T241 platform suffers from the T241-FABRIC-4 erratum which causes
unexpected behavior in the GIC when multiple transactions are received
simultaneously from different sources. This hardware issue impacts
NVIDIA server platforms that use more than two T241 chips
interconnected. Each chip has support for 320 {E}SPIs.
This issue occurs when multiple packets from different GICs are
incorrectly interleaved at the target chip. The erratum text below
specifies exactly what can cause multiple transfer packets susceptible
to interleaving and GIC state corruption. GIC state corruption can
lead to a range of problems, including kernel panics, and unexpected
behavior.
>From the erratum text:
"In some cases, inter-socket AXI4 Stream packets with multiple
transfers, may be interleaved by the fabric when presented to ARM
Generic Interrupt Controller. GIC expects all transfers of a packet
to be delivered without any interleaving.
The following GICv3 commands may result in multiple transfer packets
over inter-socket AXI4 Stream interface:
- Register reads from GICD_I* and GICD_N*
- Register writes to 64-bit GICD registers other than GICD_IROUTERn*
- ITS command MOVALL
Multiple commands in GICv4+ utilize multiple transfer packets,
including VMOVP, VMOVI, VMAPP, and 64-bit register accesses."
This issue impacts system configurations with more than 2 sockets,
that require multi-transfer packets to be sent over inter-socket
AXI4 Stream interface between GIC instances on different sockets.
GICv4 cannot be supported. GICv3 SW model can only be supported
with the workaround. Single and Dual socket configurations are not
impacted by this issue and support GICv3 and GICv4."
Link: https://developer.nvidia.com/docs/t241-fabric-4/nvidia-t241-fabric-4-errata.pdf
Writing to the chip alias region of the GICD_In{E} registers except
GICD_ICENABLERn has an equivalent effect as writing to the global
distributor. The SPI interrupt deactivate path is not impacted by
the erratum.
To fix this problem, implement a workaround that ensures read accesses
to the GICD_In{E} registers are directed to the chip that owns the
SPI, and disable GICv4.x features. To simplify code changes, the
gic_configure_irq() function uses the same alias region for both read
and write operations to GICD_ICFGR.
Co-developed-by: Vikram Sethi <vsethi@nvidia.com>
Signed-off-by: Vikram Sethi <vsethi@nvidia.com>
Signed-off-by: Shanker Donthineni <sdonthineni@nvidia.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com> (for SMCCC/SOC ID bits)
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230319024314.3540573-2-sdonthineni@nvidia.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05bb0167c8 ]
ACPICA commit 770653e3ba67c30a629ca7d12e352d83c2541b1e
Before this change we see the following UBSAN stack trace in Fuchsia:
#0 0x000021e4213b3302 in acpi_ds_init_aml_walk(struct acpi_walk_state*, union acpi_parse_object*, struct acpi_namespace_node*, u8*, u32, struct acpi_evaluate_info*, u8) ../../third_party/acpica/source/components/dispatcher/dswstate.c:682 <platform-bus-x86.so>+0x233302
#1.2 0x000020d0f660777f in ubsan_get_stack_trace() compiler-rt/lib/ubsan/ubsan_diag.cpp:41 <libclang_rt.asan.so>+0x3d77f
#1.1 0x000020d0f660777f in maybe_print_stack_trace() compiler-rt/lib/ubsan/ubsan_diag.cpp:51 <libclang_rt.asan.so>+0x3d77f
#1 0x000020d0f660777f in ~scoped_report() compiler-rt/lib/ubsan/ubsan_diag.cpp:387 <libclang_rt.asan.so>+0x3d77f
#2 0x000020d0f660b96d in handlepointer_overflow_impl() compiler-rt/lib/ubsan/ubsan_handlers.cpp:809 <libclang_rt.asan.so>+0x4196d
#3 0x000020d0f660b50d in compiler-rt/lib/ubsan/ubsan_handlers.cpp:815 <libclang_rt.asan.so>+0x4150d
#4 0x000021e4213b3302 in acpi_ds_init_aml_walk(struct acpi_walk_state*, union acpi_parse_object*, struct acpi_namespace_node*, u8*, u32, struct acpi_evaluate_info*, u8) ../../third_party/acpica/source/components/dispatcher/dswstate.c:682 <platform-bus-x86.so>+0x233302
#5 0x000021e4213e2369 in acpi_ds_call_control_method(struct acpi_thread_state*, struct acpi_walk_state*, union acpi_parse_object*) ../../third_party/acpica/source/components/dispatcher/dsmethod.c:605 <platform-bus-x86.so>+0x262369
#6 0x000021e421437fac in acpi_ps_parse_aml(struct acpi_walk_state*) ../../third_party/acpica/source/components/parser/psparse.c:550 <platform-bus-x86.so>+0x2b7fac
#7 0x000021e4214464d2 in acpi_ps_execute_method(struct acpi_evaluate_info*) ../../third_party/acpica/source/components/parser/psxface.c:244 <platform-bus-x86.so>+0x2c64d2
#8 0x000021e4213aa052 in acpi_ns_evaluate(struct acpi_evaluate_info*) ../../third_party/acpica/source/components/namespace/nseval.c:250 <platform-bus-x86.so>+0x22a052
#9 0x000021e421413dd8 in acpi_ns_init_one_device(acpi_handle, u32, void*, void**) ../../third_party/acpica/source/components/namespace/nsinit.c:735 <platform-bus-x86.so>+0x293dd8
#10 0x000021e421429e98 in acpi_ns_walk_namespace(acpi_object_type, acpi_handle, u32, u32, acpi_walk_callback, acpi_walk_callback, void*, void**) ../../third_party/acpica/source/components/namespace/nswalk.c:298 <platform-bus-x86.so>+0x2a9e98
#11 0x000021e4214131ac in acpi_ns_initialize_devices(u32) ../../third_party/acpica/source/components/namespace/nsinit.c:268 <platform-bus-x86.so>+0x2931ac
#12 0x000021e42147c40d in acpi_initialize_objects(u32) ../../third_party/acpica/source/components/utilities/utxfinit.c:304 <platform-bus-x86.so>+0x2fc40d
#13 0x000021e42126d603 in acpi::acpi_impl::initialize_acpi(acpi::acpi_impl*) ../../src/devices/board/lib/acpi/acpi-impl.cc:224 <platform-bus-x86.so>+0xed603
Add a simple check that avoids incrementing a pointer by zero, but
otherwise behaves as before. Note that our findings are against ACPICA
20221020, but the same code exists on master.
Link: https://github.com/acpica/acpica/commit/770653e3
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b20566cdef ]
The DP AUX interrupt handling was a bit of a mess.
* There were two functions (one for "native" transfers and one for
"i2c" transfers) that were quite similar. It was hard to say how
many of the differences between the two functions were on purpose
and how many of them were just an accident of how they were coded.
* Each function sometimes used "else if" to test for error bits and
sometimes didn't and again it was hard to say if this was on purpose
or just an accident.
* The two functions wouldn't notice whether "unknown" bits were
set. For instance, there seems to be a bit "DP_INTR_PLL_UNLOCKED"
and if it was set there would be no indication.
* The two functions wouldn't notice if more than one error was set.
Let's fix this by being more consistent / explicit about what we're
doing.
By design this could cause different handling for AUX transfers,
though I'm not actually aware of any bug fixed as a result of
this patch (this patch was created because we simply noticed how odd
the old code was by code inspection). Specific notes here:
1. In the old native transfer case if we got "done + wrong address"
we'd ignore the "wrong address" (because of the "else if"). Now we
won't.
2. In the old native transfer case if we got "done + timeout" we'd
ignore the "timeout" (because of the "else if"). Now we won't.
3. In the old native transfer case we'd see "nack_defer" and translate
it to the error number for "nack". This differed from the i2c
transfer case where "nack_defer" was given the error number for
"nack_defer". This 100% can't matter because the only user of this
error number treats "nack defer" the same as "nack", so it's clear
that the difference between the "native" and "i2c" was pointless
here.
4. In the old i2c transfer case if we got "done" plus any error
besides "nack" or "defer" then we'd ignore the error. Now we don't.
5. If there is more than one error signaled by the hardware it's
possible that we'll report a different one than we used to. I don't
know if this matters. If someone is aware of a case this matters we
should document it and change the code to make it explicit.
6. One quirk we keep (I don't know if this is important) is that in
the i2c transfer case if we see "done + defer" we report that as a
"nack". That seemed too intentional in the old code to just drop.
After this change we will add extra logging, including:
* A warning if we see more than one error bit set.
* A warning if we see an unexpected interrupt.
* A warning if we get an AUX transfer interrupt when shouldn't.
It actually turns out that as a result of this change then at boot we
sometimes see an error:
[drm:dp_aux_isr] *ERROR* Unexpected DP AUX IRQ 0x01000000 when not busy
That means that, during init, we are seeing DP_INTR_PLL_UNLOCKED. For
now I'm going to say that leaving this error reported in the logs is
OK-ish and hopefully it will encourage someone to track down what's
going on at init time.
One last note here is that this change renames one of the interrupt
bits. The bit named "i2c done" clearly was used for native transfers
being done too, so I renamed it to indicate this.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/520658/
Link: https://lore.kernel.org/r/20230126170745.v2.1.I90ffed3ddd21e818ae534f820cb4d6d8638859ab@changeid
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2429b3c529 ]
In tegra_sor_compute_config(), the 32-bit value mode->clock is
multiplied by 1000, and assigned to the u64 variable pclk. We can avoid
a potential 32-bit integer overflow by casting mode->clock to u64 before
we do the arithmetic and assignment.
Signed-off-by: Nur Hussein <hussein@unixcat.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35bdafda40 ]
The workqueue may execute late even after remoteproc is stopped or
stopping, some resources (rpmsg device and endpoint) have been
released in rproc_stop_subdevices(), then rproc_vq_interrupt()
accessing these resources will cause kernel dump.
Call trace:
virtqueue_add_inbuf
virtqueue_add_inbuf
rpmsg_recv_single
rpmsg_recv_done
vring_interrupt
stm32_rproc_mb_vq_work
process_one_work
worker_thread
kthread
Suggested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Link: https://lore.kernel.org/r/20230331160634.3113031-1-arnaud.pouliquen@foss.st.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37403ced9f ]
[Why]
Observing underflow on dcn30+ system config at 4k144hz
[How]
We set the UCLK hardmax on AC/DC switch if softmax is enabled
and also on boot. While booting up the UCLK Hardmax is set
to softmax before the init sequence and the init sequence
resets the hardmax to UCLK max which enables P-state switching.
Just added a conditional check to avoid setting hardmax on init.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Ayush Gupta <ayugupta@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5b492c6bb ]
When removing custom query handlers, the handler might still
be used inside the EC query workqueue, causing a kernel oops
if the module holding the callback function was already unloaded.
Fix this by flushing the EC query workqueue when removing
custom query handlers.
Tested on a Acer Travelmate 4002WLMi
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d2c48b2387 ]
Running a preempt-rt (v6.2-rc3-rt1) based kernel on an Ampere Altra
triggers:
BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:46
in_atomic(): 0, irqs_disabled(): 128, non_block: 0, pid: 24, name: cpuhp/0
preempt_count: 0, expected: 0
RCU nest depth: 0, expected: 0
3 locks held by cpuhp/0/24:
#0: ffffda30217c70d0 (cpu_hotplug_lock){++++}-{0:0}, at: cpuhp_thread_fun+0x5c/0x248
#1: ffffda30217c7120 (cpuhp_state-up){+.+.}-{0:0}, at: cpuhp_thread_fun+0x5c/0x248
#2: ffffda3021c711f0 (sdei_list_lock){....}-{3:3}, at: sdei_cpuhp_up+0x3c/0x130
irq event stamp: 36
hardirqs last enabled at (35): [<ffffda301e85b7bc>] finish_task_switch+0xb4/0x2b0
hardirqs last disabled at (36): [<ffffda301e812fec>] cpuhp_thread_fun+0x21c/0x248
softirqs last enabled at (0): [<ffffda301e80b184>] copy_process+0x63c/0x1ac0
softirqs last disabled at (0): [<0000000000000000>] 0x0
CPU: 0 PID: 24 Comm: cpuhp/0 Not tainted 5.19.0-rc3-rt5-[...]
Hardware name: WIWYNN Mt.Jade Server [...]
Call trace:
dump_backtrace+0x114/0x120
show_stack+0x20/0x70
dump_stack_lvl+0x9c/0xd8
dump_stack+0x18/0x34
__might_resched+0x188/0x228
rt_spin_lock+0x70/0x120
sdei_cpuhp_up+0x3c/0x130
cpuhp_invoke_callback+0x250/0xf08
cpuhp_thread_fun+0x120/0x248
smpboot_thread_fn+0x280/0x320
kthread+0x130/0x140
ret_from_fork+0x10/0x20
sdei_cpuhp_up() is called in the STARTING hotplug section,
which runs with interrupts disabled. Use a CPUHP_AP_ONLINE_DYN entry
instead to execute the cpuhp cb later, with preemption enabled.
SDEI originally got its own cpuhp slot to allow interacting
with perf. It got superseded by pNMI and this early slot is not
relevant anymore. [1]
Some SDEI calls (e.g. SDEI_1_0_FN_SDEI_PE_MASK) take actions on the
calling CPU. It is checked that preemption is disabled for them.
_ONLINE cpuhp cb are executed in the 'per CPU hotplug thread'.
Preemption is enabled in those threads, but their cpumask is limited
to 1 CPU.
Move 'WARN_ON_ONCE(preemptible())' statements so that SDEI cpuhp cb
don't trigger them.
Also add a check for the SDEI_1_0_FN_SDEI_PRIVATE_RESET SDEI call
which acts on the calling CPU.
[1]:
https://lore.kernel.org/all/5813b8c5-ae3e-87fd-fccc-94c9cd08816d@arm.com/
Suggested-by: James Morse <james.morse@arm.com>
Signed-off-by: Pierre Gondois <pierre.gondois@arm.com>
Reviewed-by: James Morse <james.morse@arm.com>
Link: https://lore.kernel.org/r/20230216084920.144064-1-pierre.gondois@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6326442278 ]
In r592_probe, dev->detect_timer was bound with r592_detect_timer.
In r592_irq function, the timer function will be invoked by mod_timer.
If we remove the module which will call hantro_release to make cleanup,
there may be a unfinished work. The possible sequence is as follows,
which will cause a typical UAF bug.
Fix it by canceling the work before cleanup in r592_remove.
CPU0 CPU1
|r592_detect_timer
r592_remove |
memstick_free_host|
put_device; |
kfree(host); |
|
| queue_work
| &host->media_checker //use
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Link: https://lore.kernel.org/r/20230307164338.1246287-1-zyytlz.wz@163.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b5af48eedc ]
This fixes a use-after-free crash during rmmod.
The DRM encoder is embedded inside the larger rockchip_hdmi,
which is allocated with the component. The component memory
gets freed before the main drm device is destroyed. Fix it
by running encoder cleanup before tearing down its container.
Signed-off-by: Toby Chen <tobyc@nvidia.com>
[moved encoder cleanup above clk_disable, similar to bind-error-path]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230317005126.496-1-tobyc@nvidia.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4dea41775d ]
devm_kzalloc() may fail, clk_data->name might be NULL and will
cause a NULL pointer dereference later.
Signed-off-by: Kang Chen <void0red@gmail.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1107283b33 ]
A rand config causes this link error
vmlinux.o: In function `pvr2_dvb_create':
(.text+0x8af1d2): undefined reference to `dvb_register_adapter'
The rand config has
CONFIG_VIDEO_PVRUSB2=y
CONFIG_VIDEO_DEV=y
CONFIG_DVB_CORE=m
VIDEO_PVRUSB2 should also depend on DVB_CORE.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1634b7adcc ]
When the driver calls tw68_risc_buffer() to prepare the buffer, the
function call dma_alloc_coherent may fail, resulting in a empty buffer
buf->cpu. Later when we free the buffer or access the buffer, null ptr
deref is triggered.
This bug is similar to the following one:
https://git.linuxtv.org/media_stage.git/commit/?id=2b064d91440b33fba5b452f2d1b31f13ae911d71.
We believe the bug can be also dynamically triggered from user side.
Similarly, we fix this by checking the return value of tw68_risc_buffer()
and the value of buf->cpu before buffer free.
Signed-off-by: harperchen <harperchen1110@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47e8b73bc3 ]
When the driver calls cx23885_risc_buffer() to prepare the buffer, the
function call dma_alloc_coherent may fail, resulting in a empty buffer
risc->cpu. Later when we free the buffer or access the buffer, null ptr
deref is triggered.
This bug is similar to the following one:
https://git.linuxtv.org/media_stage.git/commit/?id=2b064d91440b33fba5b452f2d1b31f13ae911d71.
We believe the bug can be also dynamically triggered from user side.
Similarly, we fix this by checking the return value of cx23885_risc_buffer()
and the value of risc->cpu before buffer free.
Signed-off-by: harperchen <harperchen1110@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 474acc639f ]
The call of mxc_jpeg_get_plane_size() from mxc_jpeg_dec_irq() sets
plane_no argument to 1. The compiler sees that it's possible to end up
with an access beyond the bounds of sizeimage, if mem_planes was too
large:
if (plane_no >= fmt->mem_planes) // mem_planes = 2+
return 0;
if (fmt->mem_planes == fmt->comp_planes) // comp_planes != mem_planes
return q_data->sizeimage[plane_no];
if (plane_no < fmt->mem_planes - 1) // mem_planes = 2
return q_data->sizeimage[plane_no];
comp_planes == 0 or 1 is safe. comp_planes > 2 would be out of bounds.
(This isn't currently possible given the contents of mxc_formats, though.)
Silence the warning by bounds checking comp_planes for future
robustness. Seen with GCC 13:
In function 'mxc_jpeg_get_plane_size',
inlined from 'mxc_jpeg_dec_irq' at ../drivers/media/platform/nxp/imx-jpeg/mxc-jpeg.c:729:14:
../drivers/media/platform/nxp/imx-jpeg/mxc-jpeg.c:641:42: warning: array subscript 2 is above array bounds of 'u32[2]' {aka 'unsigned int[2]'} [-Warray-bounds=]
641 | size += q_data->sizeimage[i];
| ~~~~~~~~~~~~~~~~~^~~
In file included from ../drivers/media/platform/nxp/imx-jpeg/mxc-jpeg-hw.h:112,
from ../drivers/media/platform/nxp/imx-jpeg/mxc-jpeg.c:63:
../drivers/media/platform/nxp/imx-jpeg/mxc-jpeg.h: In function 'mxc_jpeg_dec_irq':
../drivers/media/platform/nxp/imx-jpeg/mxc-jpeg.h:84:41: note: while referencing 'sizeimage'
84 | u32 sizeimage[MXC_JPEG_MAX_PLANES];
| ^~~~~~~~~
Cc: Mirela Rabulea <mirela.rabulea@nxp.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f3401eeb0 ]
[Why]
For dual displays where pixel rate is much higher on one display,
we may get underflow when DET is evenly allocated.
[How]
Allocate less DET segments for the lower pixel rate display and
more DET segments for the higher pixel rate display
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e8e9a895c ]
The memory manager IDR is currently destroyed when user releases the
file descriptor.
However, at this point the user context might be still held, and memory
buffers might be still in use.
Later on, calls to release those buffers will fail due to not finding
their handles in the IDR, leading to a memory leak.
To avoid this leak, split the IDR destruction from the memory manager
fini, and postpone it to hpriv_release() when there is no user context
and no buffers are used.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7222f5841f ]
[Why & How]
DC now uses a new commit sequence which is more robust since it
addresses cases where we need to reorganize pipes based on planes and
other parameters. As a result, this new commit sequence reset the DC
state by cleaning plane states and re-creating them accordingly with the
need. For this reason, the dce_transform_set_pixel_storage_depth can be
invoked after a plane state is destroyed and before its re-creation. In
this situation and on DCE devices, DC will hit a condition that will
trigger a dmesg log that looks like this:
Console: switching to colour frame buffer device 240x67
------------[ cut here ]------------
[..]
Hardware name: System manufacturer System Product Name/PRIME X370-PRO, BIOS 5603 07/28/2020
RIP: 0010:dce_transform_set_pixel_storage_depth+0x3f8/0x480 [amdgpu]
[..]
RSP: 0018:ffffc9000202b850 EFLAGS: 00010293
RAX: ffffffffa081d100 RBX: ffff888110790000 RCX: 000000000000000c
RDX: ffff888100bedbf8 RSI: 0000000000001a50 RDI: ffff88810463c900
RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000007
R10: 0000000000000001 R11: 0000000000000f00 R12: ffff88810f500010
R13: ffff888100bedbf8 R14: ffff88810f515688 R15: 0000000000000000
FS: 00007ff0159249c0(0000) GS:ffff88840e940000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007ff01528e550 CR3: 0000000002a10000 CR4: 00000000003506e0
Call Trace:
<TASK>
? dm_write_reg_func+0x21/0x80 [amdgpu 340dadd3f7c8cf4be11cf0bdc850245e99abe0e8]
dc_stream_set_dither_option+0xfb/0x130 [amdgpu 340dadd3f7c8cf4be11cf0bdc850245e99abe0e8]
amdgpu_dm_crtc_configure_crc_source+0x10b/0x190 [amdgpu 340dadd3f7c8cf4be11cf0bdc850245e99abe0e8]
amdgpu_dm_atomic_commit_tail+0x20a8/0x2a90 [amdgpu 340dadd3f7c8cf4be11cf0bdc850245e99abe0e8]
? free_unref_page_commit+0x98/0x170
? free_unref_page+0xcc/0x150
commit_tail+0x94/0x120
drm_atomic_helper_commit+0x10f/0x140
drm_atomic_commit+0x94/0xc0
? drm_plane_get_damage_clips.cold+0x1c/0x1c
drm_client_modeset_commit_atomic+0x203/0x250
drm_client_modeset_commit_locked+0x56/0x150
drm_client_modeset_commit+0x21/0x40
drm_fb_helper_lastclose+0x42/0x70
amdgpu_driver_lastclose_kms+0xa/0x10 [amdgpu 340dadd3f7c8cf4be11cf0bdc850245e99abe0e8]
drm_release+0xda/0x110
__fput+0x89/0x240
task_work_run+0x5c/0x90
do_exit+0x333/0xae0
do_group_exit+0x2d/0x90
__x64_sys_exit_group+0x14/0x20
do_syscall_64+0x5b/0x80
? exit_to_user_mode_prepare+0x1e/0x140
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7ff016ceaca1
Code: Unable to access opcode bytes at RIP 0x7ff016ceac77.
RSP: 002b:00007ffe7a2357e8 EFLAGS: 00000246 ORIG_RAX: 00000000000000e7
RAX: ffffffffffffffda RBX: 00007ff016e15a00 RCX: 00007ff016ceaca1
RDX: 000000000000003c RSI: 00000000000000e7 RDI: 0000000000000000
RBP: 0000000000000000 R08: ffffffffffffff78 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007ff016e15a00
R13: 0000000000000000 R14: 00007ff016e1aee8 R15: 00007ff016e1af00
</TASK>
Since this issue only happens in a transition state on DC, this commit
replace BREAK_TO_DEBUGGER with DC_LOG_DC.
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97fa4dfa66 ]
[Why]
There is underflow and flickering occuring. The
underflow stops when hostvm is forced to active.
According to policy, hostvm should be enabled if riommu
is active, but this is not taken into account when
deciding whether to enable hostvm.
[What]
For DCN314, set hostvm to true if riommu is active.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Gabe Teeger <gabe.teeger@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f0cf1e85d ]
The Acer Iconia One 7 B1-750 is a x86 ACPI tablet which ships with Android
x86 as factory OS. Its DSDT contains a bunch of I2C devices which are not
actually there, causing various resource conflicts. Enumeration of these
is skipped through the acpi_quirk_skip_i2c_client_enumeration().
Add support for manually instantiating the I2C + other devices which are
actually present on this tablet by adding the necessary device info to
the x86-android-tablets module.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230301092331.7038-2-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26a9f53198 ]
[Why]
In 2560x1440@240p eDP panel, some use cases will enable MPC
combine with RGB MPO then underflow happened. This case is
not allowed from HW formula.
[How]
Correct eDP, DP and DP2 output bpp calculation to align HW
formula.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Paul Hsieh <Paul.Hsieh@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9bb10b7aae ]
[Why]
System restart observed while changing the display resolution
to 8k with extended mode. Sytem restart was caused by a page fault.
[How]
When the driver populates subvp info it did it for both the pipes using
vblank which caused an outof bounds array access causing the page fault.
added checks to allow the top pipe only to fix this issue.
Co-authored-by: Ayush Gupta <ayush.gupta@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Ayush Gupta <ayush.gupta@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43b4506326 ]
After a couple of years and multiple LTS releases we received a report
that the behavior of O_DIRECTORY | O_CREAT changed starting with v5.7.
On kernels prior to v5.7 combinations of O_DIRECTORY, O_CREAT, O_EXCL
had the following semantics:
(1) open("/tmp/d", O_DIRECTORY | O_CREAT)
* d doesn't exist: create regular file
* d exists and is a regular file: ENOTDIR
* d exists and is a directory: EISDIR
(2) open("/tmp/d", O_DIRECTORY | O_CREAT | O_EXCL)
* d doesn't exist: create regular file
* d exists and is a regular file: EEXIST
* d exists and is a directory: EEXIST
(3) open("/tmp/d", O_DIRECTORY | O_EXCL)
* d doesn't exist: ENOENT
* d exists and is a regular file: ENOTDIR
* d exists and is a directory: open directory
On kernels since to v5.7 combinations of O_DIRECTORY, O_CREAT, O_EXCL
have the following semantics:
(1) open("/tmp/d", O_DIRECTORY | O_CREAT)
* d doesn't exist: ENOTDIR (create regular file)
* d exists and is a regular file: ENOTDIR
* d exists and is a directory: EISDIR
(2) open("/tmp/d", O_DIRECTORY | O_CREAT | O_EXCL)
* d doesn't exist: ENOTDIR (create regular file)
* d exists and is a regular file: EEXIST
* d exists and is a directory: EEXIST
(3) open("/tmp/d", O_DIRECTORY | O_EXCL)
* d doesn't exist: ENOENT
* d exists and is a regular file: ENOTDIR
* d exists and is a directory: open directory
This is a fairly substantial semantic change that userspace didn't
notice until Pedro took the time to deliberately figure out corner
cases. Since no one noticed this breakage we can somewhat safely assume
that O_DIRECTORY | O_CREAT combinations are likely unused.
The v5.7 breakage is especially weird because while ENOTDIR is returned
indicating failure a regular file is actually created. This doesn't make
a lot of sense.
Time was spent finding potential users of this combination. Searching on
codesearch.debian.net showed that codebases often express semantical
expectations about O_DIRECTORY | O_CREAT which are completely contrary
to what our code has done and currently does.
The expectation often is that this particular combination would create
and open a directory. This suggests users who tried to use that
combination would stumble upon the counterintuitive behavior no matter
if pre-v5.7 or post v5.7 and quickly realize neither semantics give them
what they want. For some examples see the code examples in [1] to [3]
and the discussion in [4].
There are various ways to address this issue. The lazy/simple option
would be to restore the pre-v5.7 behavior and to just live with that bug
forever. But since there's a real chance that the O_DIRECTORY | O_CREAT
quirk isn't relied upon we should try to get away with murder(ing bad
semantics) first. If we need to Frankenstein pre-v5.7 behavior later so
be it.
So let's simply return EINVAL categorically for O_DIRECTORY | O_CREAT
combinations. In addition to cleaning up the old bug this also opens up
the possiblity to make that flag combination do something more intuitive
in the future.
Starting with this commit the following semantics apply:
(1) open("/tmp/d", O_DIRECTORY | O_CREAT)
* d doesn't exist: EINVAL
* d exists and is a regular file: EINVAL
* d exists and is a directory: EINVAL
(2) open("/tmp/d", O_DIRECTORY | O_CREAT | O_EXCL)
* d doesn't exist: EINVAL
* d exists and is a regular file: EINVAL
* d exists and is a directory: EINVAL
(3) open("/tmp/d", O_DIRECTORY | O_EXCL)
* d doesn't exist: ENOENT
* d exists and is a regular file: ENOTDIR
* d exists and is a directory: open directory
One additional note, O_TMPFILE is implemented as:
#define __O_TMPFILE 020000000
#define O_TMPFILE (__O_TMPFILE | O_DIRECTORY)
#define O_TMPFILE_MASK (__O_TMPFILE | O_DIRECTORY | O_CREAT)
For older kernels it was important to return an explicit error when
O_TMPFILE wasn't supported. So O_TMPFILE requires that O_DIRECTORY is
raised alongside __O_TMPFILE. It also enforced that O_CREAT wasn't
specified. Since O_DIRECTORY | O_CREAT could be used to create a regular
allowing that combination together with __O_TMPFILE would've meant that
false positives were possible, i.e., that a regular file was created
instead of a O_TMPFILE. This could've been used to trick userspace into
thinking it operated on a O_TMPFILE when it wasn't.
Now that we block O_DIRECTORY | O_CREAT completely the check for O_CREAT
in the __O_TMPFILE branch via if ((flags & O_TMPFILE_MASK) != O_TMPFILE)
can be dropped. Instead we can simply check verify that O_DIRECTORY is
raised via if (!(flags & O_DIRECTORY)) and explain this in two comments.
As Aleksa pointed out O_PATH is unaffected by this change since it
always returned EINVAL if O_CREAT was specified - with or without
O_DIRECTORY.
Link: https://lore.kernel.org/lkml/20230320071442.172228-1-pedro.falcato@gmail.com
Link: https://sources.debian.org/src/flatpak/1.14.4-1/subprojects/libglnx/glnx-dirfd.c/?hl=324#L324 [1]
Link: https://sources.debian.org/src/flatpak-builder/1.2.3-1/subprojects/libglnx/glnx-shutil.c/?hl=251#L251 [2]
Link: https://sources.debian.org/src/ostree/2022.7-2/libglnx/glnx-dirfd.c/?hl=324#L324 [3]
Link: https://www.openwall.com/lists/oss-security/2014/11/26/14 [4]
Reported-by: Pedro Falcato <pedro.falcato@gmail.com>
Cc: Aleksa Sarai <cyphar@cyphar.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c1566bca3 ]
For kernels built with CONFIG_PREEMPT_RCU=y, the following scenario can
result in a NULL-pointer dereference:
CPU1 CPU2
rcu_preempt_deferred_qs_irqrestore rcu_print_task_exp_stall
if (special.b.blocked) READ_ONCE(rnp->exp_tasks) != NULL
raw_spin_lock_rcu_node
np = rcu_next_node_entry(t, rnp)
if (&t->rcu_node_entry == rnp->exp_tasks)
WRITE_ONCE(rnp->exp_tasks, np)
....
raw_spin_unlock_irqrestore_rcu_node
raw_spin_lock_irqsave_rcu_node
t = list_entry(rnp->exp_tasks->prev,
struct task_struct, rcu_node_entry)
(if rnp->exp_tasks is NULL, this
will dereference a NULL pointer)
The problem is that CPU2 accesses the rcu_node structure's->exp_tasks
field without holding the rcu_node structure's ->lock and CPU2 did
not observe CPU1's change to rcu_node structure's ->exp_tasks in time.
Therefore, if CPU1 sets rcu_node structure's->exp_tasks pointer to NULL,
then CPU2 might dereference that NULL pointer.
This commit therefore holds the rcu_node structure's ->lock while
accessing that structure's->exp_tasks field.
[ paulmck: Apply Frederic Weisbecker feedback. ]
Acked-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Zqiang <qiang1.zhang@intel.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c83f320e55 ]
There are several 'malloc' calls in test_memcontrol, which can be
unsuccessful. This patch will add 'malloc' failures checking to
give more details about test's fail reasons and avoid possible
undefined behavior during the future null dereference (like the
one in alloc_anon_50M_check_swap function).
Signed-off-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Reviewed-by: Muchun Song <songmuchun@bytedance.com>
Acked-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Roman Gushchin <roman.gushchin@linux.dev>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6bc6e6b275 ]
The ref_scale_shutdown() kthread/function uses wait_event() to wait for
the refscale test to complete. However, although the read-side tests
are normally extremely fast, there is no law against specifying a very
large value for the refscale.loops module parameter or against having
a slow read-side primitive. Either way, this might well trigger the
hung-task timeout.
This commit therefore replaces those wait_event() calls with calls to
wait_event_idle(), which do not trigger the hung-task timeout.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5354b2af34 ]
Previously, ext4_get_group_info() would treat an invalid group number
as BUG(), since in theory it should never happen. However, if a
malicious attaker (or fuzzer) modifies the superblock via the block
device while it is the file system is mounted, it is possible for
s_first_data_block to get set to a very large number. In that case,
when calculating the block group of some block number (such as the
starting block of a preallocation region), could result in an
underflow and very large block group number. Then the BUG_ON check in
ext4_get_group_info() would fire, resutling in a denial of service
attack that can be triggered by root or someone with write access to
the block device.
For a quality of implementation perspective, it's best that even if
the system administrator does something that they shouldn't, that it
will not trigger a BUG. So instead of BUG'ing, ext4_get_group_info()
will call ext4_error and return NULL. We also add fallback code in
all of the callers of ext4_get_group_info() that it might NULL.
Also, since ext4_get_group_info() was already borderline to be an
inline function, un-inline it. The results in a next reduction of the
compiled text size of ext4 by roughly 2k.
Cc: stable@kernel.org
Link: https://lore.kernel.org/r/20230430154311.579720-2-tytso@mit.edu
Reported-by: syzbot+e2efa3efc15a1c9e95c3@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?id=69b28112e098b070f639efb356393af3ffec4220
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 01e4ca2945 ]
If EXT4_MB_HINT_GOAL_ONLY is set, ext4_mb_regular_allocator will only
allocate blocks from ext4_mb_find_by_goal. Allow to find by goal in
ext4_mb_find_by_goal if EXT4_MB_HINT_GOAL_ONLY is set or allocation
with EXT4_MB_HINT_GOAL_ONLY set will always fail.
EXT4_MB_HINT_GOAL_ONLY is not used at all, so the problem is not
found for now.
Signed-off-by: Kemeng Shi <shikemeng@huaweicloud.com>
Reviewed-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Link: https://lore.kernel.org/r/20230303172120.3800725-3-shikemeng@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Stable-dep-of: 5354b2af34 ("ext4: allow ext4_get_group_info() to fail")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a44be64bbe ]
When a file system currently mounted read/only is remounted
read/write, if we clear the SB_RDONLY flag too early, before the quota
is initialized, and there is another process/thread constantly
attempting to create a directory, it's possible to trigger the
WARN_ON_ONCE(dquot_initialize_needed(inode));
in ext4_xattr_block_set(), with the following stack trace:
WARNING: CPU: 0 PID: 5338 at fs/ext4/xattr.c:2141 ext4_xattr_block_set+0x2ef2/0x3680
RIP: 0010:ext4_xattr_block_set+0x2ef2/0x3680 fs/ext4/xattr.c:2141
Call Trace:
ext4_xattr_set_handle+0xcd4/0x15c0 fs/ext4/xattr.c:2458
ext4_initxattrs+0xa3/0x110 fs/ext4/xattr_security.c:44
security_inode_init_security+0x2df/0x3f0 security/security.c:1147
__ext4_new_inode+0x347e/0x43d0 fs/ext4/ialloc.c:1324
ext4_mkdir+0x425/0xce0 fs/ext4/namei.c:2992
vfs_mkdir+0x29d/0x450 fs/namei.c:4038
do_mkdirat+0x264/0x520 fs/namei.c:4061
__do_sys_mkdirat fs/namei.c:4076 [inline]
__se_sys_mkdirat fs/namei.c:4074 [inline]
__x64_sys_mkdirat+0x89/0xa0 fs/namei.c:4074
Cc: stable@kernel.org
Link: https://lore.kernel.org/r/20230506142419.984260-1-tytso@mit.edu
Reported-by: syzbot+6385d7d3065524c5ca6d@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?id=6513f6cb5cd6b5fc9f37e3bb70d273b94be9c34c
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b50d5018e ]
This will allow more fine-grained errno codes to be returned by the
mount system call.
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Stable-dep-of: a44be64bbe ("ext4: don't clear SB_RDONLY when remounting r/w until quota is re-enabled")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a6bef7342 ]
Smatch complains that:
arcfb_probe() warn: 'irq' from request_irq() not released on lines: 587.
Fix error handling in the arcfb_probe() function. If IO addresses are
not provided or framebuffer registration fails, the code will jump to
the err_addr or err_register_fb label to release resources.
If IRQ request fails, previously allocated resources will be freed.
Fixes: 1154ea7dcd ("[PATCH] Framebuffer driver for Arc LCD board")
Signed-off-by: Zongjie Li <u202112089@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ff80028e2 ]
drm_dp_dsc_sink_max_slice_count() may return 0 if something goes
wrong on the part of the DSC sink and its DPCD register. This null
value may be later used as a divisor in intel_dsc_compute_params(),
which will lead to an error.
In the unlikely event that this issue occurs, fix it by testing the
return value of drm_dp_dsc_sink_max_slice_count() against zero.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: a4a157777c ("drm/i915/dp: Compute DSC pipe config in atomic check")
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230418140430.69902-1-n.zhandarovich@fintech.ru
(cherry picked from commit 51f7008239)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2da5bffe9e ]
During an IGT GPU reset test we see again oops despite of
commit 0c8c901aaaebc9 (drm/sched: Check scheduler ready before calling
timeout handling).
It uses ready condition whether to call drm_sched_fault which unwind
the TDR leads to GPU reset.
However it looks the ready condition is overloaded with other meanings,
for example, for the following stack is related GPU reset :
0 gfx_v9_0_cp_gfx_start
1 gfx_v9_0_cp_gfx_resume
2 gfx_v9_0_cp_resume
3 gfx_v9_0_hw_init
4 gfx_v9_0_resume
5 amdgpu_device_ip_resume_phase2
does the following:
/* start the ring */
gfx_v9_0_cp_gfx_start(adev);
ring->sched.ready = true;
The same approach is for other ASICs as well :
gfx_v8_0_cp_gfx_resume
gfx_v10_0_kiq_resume, etc...
As a result, our GPU reset test causes GPU fault which calls unconditionally gfx_v9_0_fault
and then drm_sched_fault. However now it depends on whether the interrupt service routine
drm_sched_fault is executed after gfx_v9_0_cp_gfx_start is completed which sets the ready
field of the scheduler to true even for uninitialized schedulers and causes oops vs
no fault or when ISR drm_sched_fault is completed prior gfx_v9_0_cp_gfx_start and
NULL pointer dereference does not occur.
Use the field timeout_wq to prevent oops for uninitialized schedulers.
The field could be initialized by the work queue of resetting the domain.
v1: Corrections to commit message (Luben)
Fixes: 11b3b9f461 ("drm/sched: Check scheduler ready before calling timeout handling")
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Link: https://lore.kernel.org/r/20230510135111.58631-1-vitaly.prosyak@amd.com
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdc2e28e21 ]
Commit d4c3676507 ("net: mscc: ocelot: keep ocelot_stat_layout by reg
address, not offset") organized the stats counters for Ocelot chips, namely
the VSC7512 and VSC7514. A few of the counter offsets were incorrect, and
were caught by this warning:
WARNING: CPU: 0 PID: 24 at drivers/net/ethernet/mscc/ocelot_stats.c:909
ocelot_stats_init+0x1fc/0x2d8
reg 0x5000078 had address 0x220 but reg 0x5000079 has address 0x214,
bulking broken!
Fix these register offsets.
Fixes: d4c3676507 ("net: mscc: ocelot: keep ocelot_stat_layout by reg address, not offset")
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4c2e67c17 ]
Clearing the PBA bit from the driver is race prone and it may lead to
dropped interrupt events. This could potentially lead to the traffic
being completely halted.
Fixes: 5e8c5adf95 ("gve: DQO: Add core netdev features")
Signed-off-by: Ziwei Xiao <ziweixiao@google.com>
Signed-off-by: Bailey Forrest <bcf@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e05a5f510f ]
do_recvmmsg() can write to sk->sk_err from multiple threads.
As said before, many other points reading or writing sk_err
need annotations.
Fixes: 34b88a68f2 ("net: Fix use after free in the recvmmsg exit path")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9949e2efb5 ]
Bonding send_peer_notif was defined as u8. Since commit 07a4ddec3c
("bonding: add an option to specify a delay between peer notifications").
the bond->send_peer_notif will be num_peer_notif multiplied by
peer_notif_delay, which is u8 * u32. This would cause the send_peer_notif
overflow easily. e.g.
ip link add bond0 type bond mode 1 miimon 100 num_grat_arp 30 peer_notify_delay 1000
To fix the overflow, let's set the send_peer_notif to u32 and limit
peer_notif_delay to 300s.
Reported-by: Liang Li <liali@redhat.com>
Closes: https://bugzilla.redhat.com/show_bug.cgi?id=2090053
Fixes: 07a4ddec3c ("bonding: add an option to specify a delay between peer notifications")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e72eeab542 ]
I received a bug report (no reproducer so far) where we trip over
712 rcu_read_lock();
713 ct_hook = rcu_dereference(nf_ct_hook);
714 BUG_ON(ct_hook == NULL); // here
In nf_conntrack_destroy().
First turn this BUG_ON into a WARN. I think it was triggered
via enable_hooks=1 flag.
When this flag is turned on, the conntrack hooks are registered
before nf_ct_hook pointer gets assigned.
This opens a short window where packets enter the conntrack machinery,
can have skb->_nfct set up and a subsequent kfree_skb might occur
before nf_ct_hook is set.
Call nf_conntrack_init_end() to set nf_ct_hook before we register the
pernet ops.
Fixes: ba3fbe6636 ("netfilter: nf_conntrack: provide modparam to always register conntrack hooks")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc1c9fd4a8 ]
This reverts "netfilter: nf_tables: skip netdev events generated on netns removal".
The problem is that when a veth device is released, the veth release
callback will also queue the peer netns device for removal.
Its possible that the peer netns is also slated for removal. In this
case, the device memory is already released before the pre_exit hook of
the peer netns runs:
BUG: KASAN: slab-use-after-free in nf_hook_entry_head+0x1b8/0x1d0
Read of size 8 at addr ffff88812c0124f0 by task kworker/u8:1/45
Workqueue: netns cleanup_net
Call Trace:
nf_hook_entry_head+0x1b8/0x1d0
__nf_unregister_net_hook+0x76/0x510
nft_netdev_unregister_hooks+0xa0/0x220
__nft_release_hook+0x184/0x490
nf_tables_pre_exit_net+0x12f/0x1b0
..
Order is:
1. First netns is released, veth_dellink() queues peer netns device
for removal
2. peer netns is queued for removal
3. peer netns device is released, unreg event is triggered
4. unreg event is ignored because netns is going down
5. pre_exit hook calls nft_netdev_unregister_hooks but device memory
might be free'd already.
Fixes: 68a3765c65 ("netfilter: nf_tables: skip netdev events generated on netns removal")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8efbdbfa99 ]
Initialize MAC_ONEUS_TIC_COUNTER register with correct value derived
from CSR clock, otherwise EEE is unstable on at least NXP i.MX8M Plus
and Micrel KSZ9131RNX PHY, to the point where not even ARP request can
be sent out.
i.MX 8M Plus Applications Processor Reference Manual, Rev. 1, 06/2021
11.7.6.1.34 One-microsecond Reference Timer (MAC_ONEUS_TIC_COUNTER)
defines this register as:
"
This register controls the generation of the Reference time (1 microsecond
tic) for all the LPI timers. This timer has to be programmed by the software
initially.
...
The application must program this counter so that the number of clock cycles
of CSR clock is 1us. (Subtract 1 from the value before programming).
For example if the CSR clock is 100MHz then this field needs to be programmed
to value 100 - 1 = 99 (which is 0x63).
This is required to generate the 1US events that are used to update some of
the EEE related counters.
"
The reset value is 0x63 on i.MX8M Plus, which means expected CSR clock are
100 MHz. However, the i.MX8M Plus "enet_qos_root_clk" are 266 MHz instead,
which means the LPI timers reach their count much sooner on this platform.
This is visible using a scope by monitoring e.g. exit from LPI mode on TX_CTL
line from MAC to PHY. This should take 30us per STMMAC_DEFAULT_TWT_LS setting,
during which the TX_CTL line transitions from tristate to low, and 30 us later
from low to high. On i.MX8M Plus, this transition takes 11 us, which matches
the 30us * 100/266 formula for misconfigured MAC_ONEUS_TIC_COUNTER register.
Configure MAC_ONEUS_TIC_COUNTER based on CSR clock, so that the LPI timers
have correct 1us reference. This then fixes EEE on i.MX8M Plus with Micrel
KSZ9131RNX PHY.
Fixes: 477286b53f ("stmmac: add GMAC4 core support")
Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Harald Seiler <hws@denx.de>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Tested-by: Francesco Dolcini <francesco.dolcini@toradex.com> # Toradex Verdin iMX8MP
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20230506235845.246105-1-marex@denx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9d36cf445 ]
When a tick broadcast clockevent device is initialized for one shot mode
then tick_broadcast_setup_oneshot() OR's the periodic broadcast mode
cpumask into the oneshot broadcast cpumask.
This is required when switching from periodic broadcast mode to oneshot
broadcast mode to ensure that CPUs which are waiting for periodic
broadcast are woken up on the next tick.
But it is subtly broken, when an active broadcast device is replaced and
the system is already in oneshot (NOHZ/HIGHRES) mode. Victor observed
this and debugged the issue.
Then the OR of the periodic broadcast CPU mask is wrong as the periodic
cpumask bits are sticky after tick_broadcast_enable() set it for a CPU
unless explicitly cleared via tick_broadcast_disable().
That means that this sets all other CPUs which have tick broadcasting
enabled at that point unconditionally in the oneshot broadcast mask.
If the affected CPUs were already idle and had their bits set in the
oneshot broadcast mask then this does no harm. But for non idle CPUs
which were not set this corrupts their state.
On their next invocation of tick_broadcast_enable() they observe the bit
set, which indicates that the broadcast for the CPU is already set up.
As a consequence they fail to update the broadcast event even if their
earliest expiring timer is before the actually programmed broadcast
event.
If the programmed broadcast event is far in the future, then this can
cause stalls or trigger the hung task detector.
Avoid this by telling tick_broadcast_setup_oneshot() explicitly whether
this is the initial switch over from periodic to oneshot broadcast which
must take the periodic broadcast mask into account. In the case of
initialization of a replacement device this prevents that the broadcast
oneshot mask is modified.
There is a second problem with broadcast device replacement in this
function. The broadcast device is only armed when the previous state of
the device was periodic.
That is correct for the switch from periodic broadcast mode to oneshot
broadcast mode as the underlying broadcast device could operate in
oneshot state already due to lack of periodic state in hardware. In that
case it is already armed to expire at the next tick.
For the replacement case this is wrong as the device is in shutdown
state. That means that any already pending broadcast event will not be
armed.
This went unnoticed because any CPU which goes idle will observe that
the broadcast device has an expiry time of KTIME_MAX and therefore any
CPUs next timer event will be earlier and cause a reprogramming of the
broadcast device. But that does not guarantee that the events of the
CPUs which were already in idle are delivered on time.
Fix this by arming the newly installed device for an immediate event
which will reevaluate the per CPU expiry times and reprogram the
broadcast device accordingly. This is simpler than caching the last
expiry time in yet another place or saving it before the device exchange
and handing it down to the setup function. Replacement of broadcast
devices is not a frequent operation and usually happens once somewhere
late in the boot process.
Fixes: 9c336c9935 ("tick/broadcast: Allow late registered device to enter oneshot mode")
Reported-by: Victor Hassan <victor@allwinnertech.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/87pm7d2z1i.ffs@tglx
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46dd6078db ]
Fix kernel-doc warnings from the kernel test robot:
jornada720_ssp.c:24: warning: Function parameter or member 'jornada_ssp_lock' not described in 'DEFINE_SPINLOCK'
jornada720_ssp.c:24: warning: expecting prototype for arch/arm/mac(). Prototype was for DEFINE_SPINLOCK() instead
jornada720_ssp.c:34: warning: Function parameter or member 'byte' not described in 'jornada_ssp_reverse'
jornada720_ssp.c:57: warning: Function parameter or member 'byte' not described in 'jornada_ssp_byte'
jornada720_ssp.c:85: warning: Function parameter or member 'byte' not described in 'jornada_ssp_inout'
Link: lore.kernel.org/r/202304210535.tWby3jWF-lkp@intel.com
Fixes: 69ebb22277 ("[ARM] 4506/1: HP Jornada 7XX: Addition of SSP Platform Driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Kristoffer Ericson <Kristoffer.ericson@gmail.com>
Cc: patches@armlinux.org.uk
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 25feda6fbd ]
More arrays (and arguments) for dcpd were set to 16, when it looks like
DP_RECEIVER_CAP_SIZE (15) should be used. Fix the remaining cases, seen
with GCC 13:
../drivers/gpu/drm/nouveau/nvif/outp.c: In function 'nvif_outp_acquire_dp':
../include/linux/fortify-string.h:57:33: warning: array subscript 'unsigned char[16][0]' is partly outside array bounds of 'u8[15]' {aka 'unsigned char[15]'} [-Warray-bounds=]
57 | #define __underlying_memcpy __builtin_memcpy
| ^
...
../drivers/gpu/drm/nouveau/nvif/outp.c:140:9: note: in expansion of macro 'memcpy'
140 | memcpy(args.dp.dpcd, dpcd, sizeof(args.dp.dpcd));
| ^~~~~~
../drivers/gpu/drm/nouveau/nvif/outp.c:130:49: note: object 'dpcd' of size [0, 15]
130 | nvif_outp_acquire_dp(struct nvif_outp *outp, u8 dpcd[DP_RECEIVER_CAP_SIZE],
| ~~~^~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: 8134437213 ("drm/nouveau/disp: move DP link config into acquire")
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Karol Herbst <kherbst@redhat.com>
Cc: David Airlie <airlied@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Dave Airlie <airlied@redhat.com>
Cc: "Gustavo A. R. Silva" <gustavo@embeddedor.com>
Cc: dri-devel@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Karol Herbst <git@karolherbst.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230204184307.never.825-kees@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8687694bb ]
The fbdev test of IGT may write after EOF, which lead to out-of-bound
access for drm drivers with fbdev-generic. For example, run fbdev test
on a x86+ast2400 platform, with 1680x1050 resolution, will cause the
linux kernel hang with the following call trace:
Oops: 0000 [#1] PREEMPT SMP PTI
[IGT] fbdev: starting subtest eof
Workqueue: events drm_fb_helper_damage_work [drm_kms_helper]
[IGT] fbdev: starting subtest nullptr
RIP: 0010:memcpy_erms+0xa/0x20
RSP: 0018:ffffa17d40167d98 EFLAGS: 00010246
RAX: ffffa17d4eb7fa80 RBX: ffffa17d40e0aa80 RCX: 00000000000014c0
RDX: 0000000000001a40 RSI: ffffa17d40e0b000 RDI: ffffa17d4eb80000
RBP: ffffa17d40167e20 R08: 0000000000000000 R09: ffff89522ecff8c0
R10: ffffa17d4e4c5000 R11: 0000000000000000 R12: ffffa17d4eb7fa80
R13: 0000000000001a40 R14: 000000000000041a R15: ffffa17d40167e30
FS: 0000000000000000(0000) GS:ffff895257380000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffa17d40e0b000 CR3: 00000001eaeca006 CR4: 00000000001706e0
Call Trace:
<TASK>
? drm_fbdev_generic_helper_fb_dirty+0x207/0x330 [drm_kms_helper]
drm_fb_helper_damage_work+0x8f/0x170 [drm_kms_helper]
process_one_work+0x21f/0x430
worker_thread+0x4e/0x3c0
? __pfx_worker_thread+0x10/0x10
kthread+0xf4/0x120
? __pfx_kthread+0x10/0x10
ret_from_fork+0x2c/0x50
</TASK>
CR2: ffffa17d40e0b000
---[ end trace 0000000000000000 ]---
The is because damage rectangles computed by
drm_fb_helper_memory_range_to_clip() function is not guaranteed to be
bound in the screen's active display area. Possible reasons are:
1) Buffers are allocated in the granularity of page size, for mmap system
call support. The shadow screen buffer consumed by fbdev emulation may
also choosed be page size aligned.
2) The DIV_ROUND_UP() used in drm_fb_helper_memory_range_to_clip()
will introduce off-by-one error.
For example, on a 16KB page size system, in order to store a 1920x1080
XRGB framebuffer, we need allocate 507 pages. Unfortunately, the size
1920*1080*4 can not be divided exactly by 16KB.
1920 * 1080 * 4 = 8294400 bytes
506 * 16 * 1024 = 8290304 bytes
507 * 16 * 1024 = 8306688 bytes
line_length = 1920*4 = 7680 bytes
507 * 16 * 1024 / 7680 = 1081.6
off / line_length = 507 * 16 * 1024 / 7680 = 1081
DIV_ROUND_UP(507 * 16 * 1024, 7680) will yeild 1082
memcpy_toio() typically issue the copy line by line, when copy the last
line, out-of-bound access will be happen. Because:
1082 * line_length = 1082 * 7680 = 8309760, and 8309760 > 8306688
Note that userspace may still write to the invisiable area if a larger
buffer than width x stride is exposed. But it is not a big issue as
long as there still have memory resolve the access if not drafting so
far.
- Also limit the y1 (Daniel)
- keep fix patch it to minimal (Daniel)
- screen_size is page size aligned because of it need mmap (Thomas)
- Adding fixes tag (Thomas)
Signed-off-by: Sui Jingfeng <suijingfeng@loongson.cn>
Fixes: aa15c677cc ("drm/fb-helper: Fix vertical damage clipping")
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/dri-devel/ad44df29-3241-0d9e-e708-b0338bf3c623@189.cn/
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230420030500.1578756-1-suijingfeng@loongson.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 81e8479649 ]
Commit bb1520d581 ("s390/mm: start kernel with DAT enabled") did not
implement direct map accounting in the early page table setup code. In
result the reported values are bogus now:
$cat /proc/meminfo
...
DirectMap4k: 5120 kB
DirectMap1M: 18446744073709546496 kB
DirectMap2G: 0 kB
Fix this by adding the missing accounting. The result looks sane again:
$cat /proc/meminfo
...
DirectMap4k: 6156 kB
DirectMap1M: 2091008 kB
DirectMap2G: 6291456 kB
Fixes: bb1520d581 ("s390/mm: start kernel with DAT enabled")
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 07fdd6627f ]
Architectures generally use the "direct map" wording for mapping the whole
physical memory. Use that wording as well in arch/s390/boot/vmem.c, instead
of "one to one" in order to avoid confusion.
This also matches what is already done in arch/s390/mm/vmem.c.
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc96ec826b upstream.
On CPM, the RISC core is a lot more efficiant when doing transfers
in 16-bits chunks than in 8-bits chunks, but unfortunately the
words need to be byte swapped as seen in a previous commit.
So, for large tranfers with an even size, allocate a temporary tx
buffer and byte-swap data before and after transfer.
This change allows setting higher speed for transfer. For instance
on an MPC 8xx (CPM1 comms RISC processor), the documentation tells
that transfer in byte mode at 1 kbit/s uses 0.200% of CPM load
at 25 MHz while a word transfer at the same speed uses 0.032%
of CPM load. This means the speed can be 6 times higher in
word mode for the same CPM load.
For the time being, only do it on CPM1 as there must be a
trade-off between the CPM load reduction and the CPU load required
to byte swap the data.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/f2e981f20f92dd28983c3949702a09248c23845c.1680371809.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a5299a127 upstream.
For different reasons, fsl-spi driver performs bits_per_word
modifications for different reasons:
- On CPU mode, to minimise amount of interrupts
- On CPM/QE mode to work around controller byte order
For CPU mode that's done in fsl_spi_prepare_message() while
for CPM mode that's done in fsl_spi_setup_transfer().
Reunify all of it in fsl_spi_prepare_message(), and catch
impossible cases early through master's bits_per_word_mask
instead of returning EINVAL later.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/0ce96fe96e8b07cba0613e4097cfd94d09b8919a.1680371809.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This code no longer exists in mainline, because it was removed in
commit d2c95f9d68 ("x86: don't use REP_GOOD or ERMS for user memory
clearing") upstream.
However, rather than backport the full range of x86 memory clearing and
copying cleanups, fix the exception table annotation placement for the
final 'rep movsb' in clear_user_rep_good(): rather than pointing at the
actual instruction that did the user space access, it pointed to the
register move just before it.
That made sense from a code flow standpoint, but not from an actual
usage standpoint: it means that if user access takes an exception, the
exception handler won't actually find the instruction in the exception
tables.
As a result, rather than fixing it up and returning -EFAULT, it would
then turn it into a kernel oops report instead, something like:
BUG: unable to handle page fault for address: 0000000020081000
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
...
RIP: 0010:clear_user_rep_good+0x1c/0x30 arch/x86/lib/clear_page_64.S:147
...
Call Trace:
__clear_user arch/x86/include/asm/uaccess_64.h:103 [inline]
clear_user arch/x86/include/asm/uaccess_64.h:124 [inline]
iov_iter_zero+0x709/0x1290 lib/iov_iter.c:800
iomap_dio_hole_iter fs/iomap/direct-io.c:389 [inline]
iomap_dio_iter fs/iomap/direct-io.c:440 [inline]
__iomap_dio_rw+0xe3d/0x1cd0 fs/iomap/direct-io.c:601
iomap_dio_rw+0x40/0xa0 fs/iomap/direct-io.c:689
ext4_dio_read_iter fs/ext4/file.c:94 [inline]
ext4_file_read_iter+0x4be/0x690 fs/ext4/file.c:145
call_read_iter include/linux/fs.h:2183 [inline]
do_iter_readv_writev+0x2e0/0x3b0 fs/read_write.c:733
do_iter_read+0x2f2/0x750 fs/read_write.c:796
vfs_readv+0xe5/0x150 fs/read_write.c:916
do_preadv+0x1b6/0x270 fs/read_write.c:1008
__do_sys_preadv2 fs/read_write.c:1070 [inline]
__se_sys_preadv2 fs/read_write.c:1061 [inline]
__x64_sys_preadv2+0xef/0x150 fs/read_write.c:1061
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x39/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
which then looks like a filesystem bug rather than the incorrect
exception annotation that it is.
[ The alternative to this one-liner fix is to take the upstream series
that cleans this all up:
68674f94ff ("x86: don't use REP_GOOD or ERMS for small memory copies")
20f3337d35 ("x86: don't use REP_GOOD or ERMS for small memory clearing")
adfcf4231b ("x86: don't use REP_GOOD or ERMS for user memory copies")
* d2c95f9d68 ("x86: don't use REP_GOOD or ERMS for user memory clearing")
3639a53558 ("x86: move stac/clac from user copy routines into callers")
577e6a7fd5 ("x86: inline the 'rep movs' in user copies for the FSRM case")
8c9b6a88b7 ("x86: improve on the non-rep 'clear_user' function")
427fda2c8a ("x86: improve on the non-rep 'copy_user' function")
* e046fe5a36 ("x86: set FSRS automatically on AMD CPUs that have FSRM")
e1f2750edc ("x86: remove 'zerorest' argument from __copy_user_nocache()")
034ff37d34 ("x86: rewrite '__copy_user_nocache' function")
with either the whole series or at a minimum the two marked commits
being needed to fix this issue ]
Reported-by: syzbot <syzbot+401145a9a237779feb26@syzkaller.appspotmail.com>
Link: https://syzkaller.appspot.com/bug?extid=401145a9a237779feb26
Fixes: 0db7058e8e ("x86/clear_user: Make it faster")
Cc: Borislav Petkov <bp@alien8.de>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23a5b8bb02 upstream.
Commit
310e782a99 ("platform/x86/amd: pmc: Utilize SMN index 0 for driver probe")
switched to using amd_smn_read() which relies upon the misc PCI ID used
by DF function 3 being included in a table. The ID for model 78h is
missing in that table, so amd_smn_read() doesn't work.
Add the missing ID into amd_nb, restoring s2idle on this system.
[ bp: Simplify commit message. ]
Fixes: 310e782a99 ("platform/x86/amd: pmc: Utilize SMN index 0 for driver probe")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # pci_ids.h
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230427053338.16653-2-mario.limonciello@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a534e1d0d upstream.
In ext4_update_inline_data(), if ext4_xattr_ibody_get() fails for any
reason, it's best if we just fail as opposed to stumbling on,
especially if the failure is EFSCORRUPTED.
Cc: stable@kernel.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c0b4818b1 upstream.
If there are failures while changing the mount options in
__ext4_remount(), we need to restore the old mount options.
This commit fixes two problem. The first is there is a chance that we
will free the old quota file names before a potential failure leading
to a use-after-free. The second problem addressed in this commit is
if there is a failed read/write to read-only transition, if the quota
has already been suspended, we need to renable quota handling.
Cc: stable@kernel.org
Link: https://lore.kernel.org/r/20230506142419.984260-2-tytso@mit.edu
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 00d873c17e upstream.
Ext4 has a filesystem wide lock protecting ext4_writepages() calls to
avoid races with switching of journalled data flag or inode format. This
lock can however cause a deadlock like:
CPU0 CPU1
ext4_writepages()
percpu_down_read(sbi->s_writepages_rwsem);
ext4_change_inode_journal_flag()
percpu_down_write(sbi->s_writepages_rwsem);
- blocks, all readers block from now on
ext4_do_writepages()
ext4_init_io_end()
kmem_cache_zalloc(io_end_cachep, GFP_KERNEL)
fs_reclaim frees dentry...
dentry_unlink_inode()
iput() - last ref =>
iput_final() - inode dirty =>
write_inode_now()...
ext4_writepages() tries to acquire sbi->s_writepages_rwsem
and blocks forever
Make sure we cannot recurse into filesystem reclaim from writeback code
to avoid the deadlock.
Reported-by: syzbot+6898da502aef574c5f8a@syzkaller.appspotmail.com
Link: https://lore.kernel.org/all/0000000000004c66b405fa108e27@google.com
Fixes: c8585c6fca ("ext4: fix races between changing inode journal mode and ext4_writepages")
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20230504124723.20205-1-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92cc5d00a4 upstream.
Apparently despite it being marked inline, the compiler
may not inline __down_read_common() which makes it difficult
to identify the cause of lock contention, as the blocked
function in traceevents will always be listed as
__down_read_common().
So this patch adds __always_inline annotation to the common
function (as well as the inlined helper callers) to force it to
be inlined so the blocking function will be listed (via Wchan)
in traceevents.
Fixes: c995e638cc ("locking/rwsem: Fold __down_{read,write}*()")
Reported-by: Tim Murray <timmurray@google.com>
Signed-off-by: John Stultz <jstultz@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Waiman Long <longman@redhat.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20230503023351.2832796-1-jstultz@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0215ce9057 ]
[Why]
Block periods that are too short as they have the potential to
currently cause hangs in other firmware components on the system.
[How]
Update the threshold, mostly targeting a block of 4k and downscaling.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stable-dep-of: d893f39320 ("drm/amd/display: Lowering min Z8 residency time")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 81900e3a37 ]
By default the indirect state sampler data (border colors) are stored
in the same heap as the SAMPLER_STATE structure. For userspace drivers
that can be 2 different heaps (dynamic state heap & bindless sampler
state heap). This means that border colors have to copied in 2
different places so that the same SAMPLER_STATE structure find the
right data.
This change is forcing the indirect state sampler data to only be in
the dynamic state pool (more convenient for userspace drivers, they
only have to have one copy of the border colors). This is reproducing
the behavior of the Windows drivers.
BSpec: 46052
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Haridhar Kalvala <haridhar.kalvala@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230407093237.3296286-1-lionel.g.landwerlin@intel.com
(cherry picked from commit 16fc9c08f0)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 357513233d ]
It's a constant pattern in the driver to need to use 2 ranges of MMIOs
based on port, phy, pll, etc. When that happens, instead of using
_PICK_EVEN(), _PICK() needs to be used. Using _PICK() is discouraged
due to some reasons like:
1) It increases the code size since the array is declared
in each call site
2) Developers need to be careful not to incur an
out-of-bounds array access
3) Developers need to be careful that the indexes match the
table. For that it may be that the table needs to contain
holes, making (1) even worse.
Add a variant of _PICK_EVEN() that works with 2 ranges and selects which
one to use depending on the index value.
v2: Fix the address expansion in the example (Anusha)
v3: Also rename macro to _PICK_EVEN_2RANGES() in the documentation
and reword it to clarify what ranges are chosen based on the index
(Jani)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230125182403.7526-1-lucas.demarchi@intel.com
Stable-dep-of: 214b09db61 ("drm/msm: fix drm device leak on bind errors")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ae1dbe654 ]
[why]
Remove the need to include dc_link.h separately. dc.h should contain
everything needed on DM side.
[How]
Merge dc_link.h into dc.h and dc_types.h so DM only needs to include
dc.h to use all link public functions.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stable-dep-of: eeefe7c482 ("drm/amd/display: hpd rx irq not working with eDP interface")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3eeca5e5f3 upstream.
The adreno_load_gpu() path is guarded by an error check on
adreno_load_fw(). This function is responsible for loading
Qualcomm-only-signed binaries (e.g. SQE and GMU FW for A6XX), but it
does not take the vendor-signed ZAP blob into account.
By embedding the SQE (and GMU, if necessary) firmware into the
initrd/kernel, we can trigger and unfortunate path that would not bail
out early and proceed with gpu->hw_init(). That will fail, as the ZAP
loader path will not find the firmware and return back to
adreno_load_gpu().
This error path involves pm_runtime_put_sync() which then calls idle()
instead of suspend(). This is suboptimal, as it means that we're not
going through the clean shutdown sequence. With at least A619_holi, this
makes the GPU not wake up until it goes through at least one more
start-fail-stop cycle. The pm_runtime_put_sync that appears in the error
path actually does not guarantee that because of the earlier enabling of
runtime autosuspend.
Fix that by using pm_runtime_put_sync_suspend to force a clean shutdown.
Test cases:
1. All firmware baked into kernel
2. error loading ZAP fw in initrd -> load from rootfs at DE start
Both succeed on A619_holi (SM6375) and A630 (SDM845).
Fixes: 0d997f95b7 ("drm/msm/adreno: fix runtime PM imbalance at gpu load")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/530001/
Link: https://lore.kernel.org/r/20230330231517.2747024-1-konrad.dybcio@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 17d793f3ed upstream.
To fully utilize the BT polling/refresh rate, a few input events
are sent together to reduce event delay. This causes issue to the
timestamp generated by input_sync since all the events in the same
packet would pretty much have the same timestamp. This patch inserts
time interval to the events by averaging the total time used for
sending the packet.
This decision was mainly based on observing the actual time interval
between each BT polling. The interval doesn't seem to be constant,
due to the network and system environment. So, using solutions other
than averaging doesn't end up with valid timestamps.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5247f05ead upstream.
Prevent further dpm casting on legacy asics without od_enabled in
amdgpu_dpm_is_overdrive_supported. This can avoid UBSAN complain
in init sequence.
v2: add a macro to check legacy dpm instead of checking asic family/type
v3: refine macro name for naming consistency
Suggested-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 720b47229a upstream.
The gfx.cp_ecc_error_irq is retired in gfx11. In gfx_v11_0_hw_fini still
use amdgpu_irq_put to disable this interrupt, which caused the call trace
in this function.
[ 102.873958] Call Trace:
[ 102.873959] <TASK>
[ 102.873961] gfx_v11_0_hw_fini+0x23/0x1e0 [amdgpu]
[ 102.874019] gfx_v11_0_suspend+0xe/0x20 [amdgpu]
[ 102.874072] amdgpu_device_ip_suspend_phase2+0x240/0x460 [amdgpu]
[ 102.874122] amdgpu_device_ip_suspend+0x3d/0x80 [amdgpu]
[ 102.874172] amdgpu_device_pre_asic_reset+0xd9/0x490 [amdgpu]
[ 102.874223] amdgpu_device_gpu_recover.cold+0x548/0xce6 [amdgpu]
[ 102.874321] amdgpu_debugfs_reset_work+0x4c/0x70 [amdgpu]
[ 102.874375] process_one_work+0x21f/0x3f0
[ 102.874377] worker_thread+0x200/0x3e0
[ 102.874378] ? process_one_work+0x3f0/0x3f0
[ 102.874379] kthread+0xfd/0x130
[ 102.874380] ? kthread_complete_and_exit+0x20/0x20
[ 102.874381] ret_from_fork+0x22/0x30
v2:
- Handle umc and gfx ras cases in separated patch
- Retired the gfx_v11_0_cp_ecc_error_irq_funcs in gfx11
v3:
- Improve the subject and code comments
- Add judgment on gfx11 in the function of amdgpu_gfx_ras_late_init
v4:
- Drop the define of CP_ME1_PIPE_INST_ADDR_INTERVAL and
SET_ECC_ME_PIPE_STATE which using in gfx_v11_0_set_cp_ecc_error_state
- Check cp_ecc_error_irq.funcs rather than ip version for a more
sustainable life
v5:
- Simplify judgment conditions
Signed-off-by: Horatio Zhang <Hongkun.Zhang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c032c37ac upstream.
v1: Vmbo->shadow is used to back vram bo up when vram lost. So that we
should set shadow as vmbo->shadow to recover vmbo->bo
v2: Modify if(vmbo->shadow) shadow = vmbo->shadow as if(!vmbo->shadow)
continue;
Fixes: e18aaea733 ("drm/amdgpu: move shadow_list to amdgpu_bo_vm")
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Lin.Cao <lincao12@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08da182175 upstream.
Currently, on a handful of ASICs. We allow the framebuffer for a given
plane to exist in either VRAM or GTT. However, if the plane's new
framebuffer is in a different memory domain than it's previous
framebuffer, flipping between them can cause the screen to flicker. So,
to fix this, don't perform an immediate flip in the aforementioned case.
Cc: stable@vger.kernel.org
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2354
Reviewed-by: Roman Li <Roman.Li@amd.com>
Fixes: 81d0bcf990 ("drm/amdgpu: make display pinning more flexible (v2)")
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf224e00a9 upstream.
[Why]
DPP Root clock optimization when combined with 4to1 MPC combine results
in the screen turning black.
This is because the DPPCLK is stopped during the middle of an
optimize_bandwidth sequence during commit_minimal_transition without
going through plane power down/power up.
[How]
The intent of a 0Hz DPP clock through update_clocks is to disable the
DTO. This differs from the behavior of stopping the DPPCLK entirely
(utilizing a 0Hz clock on some ASIC) so it's better to move this logic
to reside next to plane power up/power down where we gate the HUBP/DPP
DOMAIN.
The new sequence should be:
Power down: PG enabled -> RCO on
Power up: RCO off -> PG disabled
Rename power_on_plane to power_on_plane_resources to reflect the
actual operation that's occurring.
Cc: stable@vger.kernel.org
Cc: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 64cc451e45 upstream.
In eiointc_acpi_init(), a *eiointc* node is passed into
acpi_get_vec_parent() instead of a required *NUMA* node (on some chip
like 3C5000L, a *NUMA* node means a *eiointc* node, but on some chip
like 3C5000, a *NUMA* node contains 4 *eiointc* nodes), and node in
struct acpi_vector_group is essentially a *NUMA* node, which will
lead to no parent matched for passed *eiointc* node. so the patch
adjusts code to use *NUMA* node for parameter node of
acpi_set_vec_parent/acpi_get_vec_parent.
Cc: stable@vger.kernel.org
Signed-off-by: Jianmin Lv <lvjianmin@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230407083453.6305-3-lvjianmin@loongson.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 112eaa8fec upstream.
In pch_pic_parse_madt(), a NULL parent pointer will be
returned from acpi_get_vec_parent() for second pch-pic domain
related to second bridge while calling eiointc_acpi_init() at
first time, where the parent of it has not been initialized
yet, and will be initialized during second time calling
eiointc_acpi_init(). So, it's reasonable to return zero so
that failure of acpi_table_parse_madt() will be avoided, or else
acpi_cascade_irqdomain_init() will return and initialization of
followed pch_msi domain will be skipped.
Although it does not matter when pch_msi_parse_madt() returns
-EINVAL if no invalid parent is found, it's also reasonable to
return zero for that.
Cc: stable@vger.kernel.org
Signed-off-by: Jianmin Lv <lvjianmin@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230407083453.6305-2-lvjianmin@loongson.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 48ce2d722f upstream.
For dual-bridges scenario, pch_pic_acpi_init() will be called
in following path:
cpuintc_acpi_init
acpi_cascade_irqdomain_init(in cpuintc driver)
acpi_table_parse_madt
eiointc_parse_madt
eiointc_acpi_init /* this will be called two times
correspondingto parsing two
eiointc entries in MADT under
dual-bridges scenario*/
acpi_cascade_irqdomain_init(in eiointc driver)
acpi_table_parse_madt
pch_pic_parse_madt
pch_pic_acpi_init /* this will be called depend
on valid parent IRQ domain
handle for one or two times
corresponding to parsing
two pchpic entries in MADT
druring calling
eiointc_acpi_init() under
dual-bridges scenario*/
During the first eiointc_acpi_init() calling, the
pch_pic_acpi_init() will be called just one time since only
one valid parent IRQ domain handle will be found for current
eiointc IRQ domain.
During the second eiointc_acpi_init() calling, the
pch_pic_acpi_init() will be called two times since two valid
parent IRQ domain handles will be found. So in pch_pic_acpi_init(),
we must have a reasonable way to prevent from creating second same
pch_pic IRQ domain.
The patch matches gsi base information in created pch_pic IRQ
domains to check if the target domain has been created to avoid the
bug mentioned above.
Cc: stable@vger.kernel.org
Signed-off-by: Jianmin Lv <lvjianmin@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230407083453.6305-6-lvjianmin@loongson.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf21acf995 upstream.
This is a last part to remove the memory sharing for rb_tree in extent_cache.
This should also fix arm32 memory alignment issue.
[struct extent_node] [struct rb_entry]
[0] struct rb_node rb_node; [0] struct rb_node rb_node;
union { union {
struct { struct {
[16] unsigned int fofs; [12] unsigned int ofs;
unsigned int len; unsigned int len;
};
unsigned long long key;
} __packed;
Cc: <stable@vger.kernel.org>
Fixes: 13054c548a ("f2fs: introduce infra macro and data structure of rb-tree extent cache")
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f69475dd48 upstream.
This is a second part to remove the mixed use of rb_tree in discard_cmd from
extent_cache.
This should also fix arm32 memory alignment issue caused by shared rb_entry.
[struct discard_cmd] [struct rb_entry]
[0] struct rb_node rb_node; [0] struct rb_node rb_node;
union { union {
struct { struct {
[16] block_t lstart; [12] unsigned int ofs;
block_t len; unsigned int len;
};
unsigned long long key;
} __packed;
Cc: <stable@vger.kernel.org>
Fixes: 004b686218 ("f2fs: use rb-tree to track pending discard commands")
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 043d2d00b4 upstream.
Let's reduce the complexity of mixed use of rb_tree in victim_entry from
extent_cache and discard_cmd.
This should fix arm32 memory alignment issue caused by shared rb_entry.
[struct victim_entry] [struct rb_entry]
[0] struct rb_node rb_node; [0] struct rb_node rb_node;
union {
struct {
unsigned int ofs;
unsigned int len;
};
[16] unsigned long long mtime; [12] unsigned long long key;
} __packed;
Cc: <stable@vger.kernel.org>
Fixes: 093749e296 ("f2fs: support age threshold based garbage collection")
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8c2969bfc upstream.
The intel_dsi_msleep() helper skips sleeping if the MIPI-sequences have
a version of 3 or newer and the panel is in vid-mode.
This is based on the big comment around line 730 which starts with
"Panel enable/disable sequences from the VBT spec.", where
the "v3 video mode seq" column does not have any wait t# entries.
Checking the Windows driver shows that it does always honor
the VBT delays independent of the version of the VBT sequences.
Commit 6fdb335f1c ("drm/i915/dsi: Use unconditional msleep for
the panel_on_delay when there is no reset-deassert MIPI-sequence")
switched to a direct msleep() instead of intel_dsi_msleep()
when there is no MIPI_SEQ_DEASSERT_RESET sequence, to fix
the panel on an Acer Aspire Switch 10 E SW3-016 not turning on.
And now testing on a Nextbook Ares 8A shows that panel_on_delay
must always be honored otherwise the panel will not turn on.
Instead of only always using regular msleep() for panel_on_delay
do as Windows does and always use regular msleep() everywhere
were intel_dsi_msleep() is used and drop the intel_dsi_msleep()
helper.
Changes in v2:
- Replace all intel_dsi_msleep() calls instead of just
the intel_dsi_msleep(panel_on_delay) call
Cc: stable@vger.kernel.org
Fixes: 6fdb335f1c ("drm/i915/dsi: Use unconditional msleep for the panel_on_delay when there is no reset-deassert MIPI-sequence")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230425194441.68086-1-hdegoede@redhat.com
(cherry picked from commit fa83c12132)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1dc8689e4c upstream.
Expand documentation to clarify:
o that paths don't need to exist for the new API callers
o clarify that we *require* callers to keep the memory of
the table around during the lifetime of the sysctls
o annotate routines we are trying to deprecate and later remove
Cc: stable@vger.kernel.org # v5.17
Cc: Christian Brauner <brauner@kernel.org>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67ff32289a upstream.
Update the docs for __register_sysctl_table() to make it clear no child
entries can be passed. When the child is true these are non-leaf entries
on the ctl table and sysctl treats these as directories. The point to
__register_sysctl_table() is to deal only with directories not part of
the ctl table where thay may riside, to be simple and avoid recursion.
While at it, hint towards using long on extra1 and extra2 later.
Cc: stable@vger.kernel.org # v5.17
Cc: Christian Brauner <brauner@kernel.org>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2cb6f96877 upstream.
In investigating a failure with xfstest generic/392 it
was noticed that mounts were reusing a superblock that should
already have been freed. This turned out to be related to
deferred close files keeping a reference count until the
closetimeo expired.
Currently the only way an fs knows that mount is beginning is
when force unmount is called, but when this, ie umount_begin(),
is called all deferred close files on the share (tree
connection) should be closed immediately (unless shared by
another mount) to avoid using excess resources on the server
and to avoid reusing a superblock which should already be freed.
In umount_begin, close all deferred close handles for that
share if this is the last mount using that share on this
client (ie send the SMB3 close request over the wire for those
that have been already closed by the app but that we have
kept a handle lease open for and have not sent closes to the
server for yet).
Reported-by: David Howells <dhowells@redhat.com>
Acked-by: Bharath SM <bharathsm@microsoft.com>
Cc: <stable@vger.kernel.org>
Fixes: 78c09634f7 ("Cifs: Fix kernel oops caused by deferred close for files.")
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 716a3cf317 upstream.
xfstests generic/392 showed a problem where even after a
shutdown call was made on a mount, we would still attempt
to use the (now inaccessible) superblock if another mount
was attempted for the same share.
Reported-by: David Howells <dhowells@redhat.com>
Reviewed-by: David Howells <dhowells@redhat.com>
Cc: <stable@vger.kernel.org>
Fixes: 087f757b01 ("cifs: add shutdown support")
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c915d8f591 upstream.
When inotify_freeing_mark() races with inotify_handle_inode_event() it
can happen that inotify_handle_inode_event() sees that i_mark->wd got
already reset to -1 and reports this value to userspace which can
confuse the inotify listener. Avoid the problem by validating that wd is
sensible (and pretend the mark got removed before the event got
generated otherwise).
CC: stable@vger.kernel.org
Fixes: 7e790dd5fc ("inotify: fix error paths in inotify_update_watch")
Message-Id: <20230424163219.9250-1-jack@suse.cz>
Reported-by: syzbot+4a06d4373fd52f0b2f9c@syzkaller.appspotmail.com
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1684878952 upstream.
There has been a lot of confusion around which platform profiles are
supported on various platforms and it would be useful to have a debug
method to be able to override the profile mode that is selected.
I don't expect this to be used in anything other than debugging in
conjunction with Lenovo engineers - but it does give a way to get a
system working whilst we wait for either FW fixes, or a driver fix
to land upstream, if something is wonky in the mode detection logic
Signed-off-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Link: https://lore.kernel.org/r/20230505132523.214338-2-mpearson-lenovo@squebb.ca
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c0cd3e25a upstream.
I had incorrectly thought that PSC profiles were not usable on Intel
platforms so had blocked them in the driver initialistion. This broke
platform profiles on the T490.
After discussion with the FW team PSC does work on Intel platforms and
should be allowed.
Note - it's possible this may impact other platforms where it is advertised
but special driver support that only Windows has is needed. But if it does
then they will need fixing via quirks. Please report any issues to me so I
can get them addressed - but I haven't found any problems in testing...yet
Fixes: bce6243f76 ("platform/x86: thinkpad_acpi: do not use PSC mode on Intel platforms")
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2177962
Cc: stable@vger.kernel.org
Signed-off-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Link: https://lore.kernel.org/r/20230505132523.214338-1-mpearson-lenovo@squebb.ca
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d66cde50c3 upstream.
Change type of pcchunk->Length from u32 to u64 to match
smb2_copychunk_range arguments type. Fixes the problem where performing
server-side copy with CIFS_IOC_COPYCHUNK_FILE ioctl resulted in incomplete
copy of large files while returning -EINVAL.
Fixes: 9bf0c9cd43 ("CIFS: Fix SMB2/SMB3 Copy offload support (refcopy) for large files")
Cc: <stable@vger.kernel.org>
Signed-off-by: Pawel Witek <pawel.ireneusz.witek@gmail.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0cad8f14d7 upstream.
When using the logical to ino ioctl v2, if the flag to ignore offsets of
file extent items (BTRFS_LOGICAL_INO_ARGS_IGNORE_OFFSET) is given, the
backref walking code ends up not returning references for all file offsets
of an inode that point to the given logical bytenr. This happens since
kernel 6.2, commit 6ce6ba5344 ("btrfs: use a single argument for extent
offset in backref walking functions") because:
1) It mistakenly skipped the search for file extent items in a leaf that
point to the target extent if that flag is given. Instead it should
only skip the filtering done by check_extent_in_eb() - that is, it
should not avoid the calls to that function (or find_extent_in_eb(),
which uses it).
2) It was also not building a list of inode extent elements (struct
extent_inode_elem) if we have multiple inode references for an extent
when the ignore offset flag is given to the logical to ino ioctl - it
would leave a single element, only the last one that was found.
These stem from the confusing old interface for backref walking functions
where we had an extent item offset argument that was a pointer to a u64
and another boolean argument that indicated if the offset should be
ignored, but the pointer could be NULL. That NULL case is used by
relocation, qgroup extent accounting and fiemap, simply to avoid building
the inode extent list for each reference, as it's not necessary for those
use cases and therefore avoids memory allocations and some computations.
Fix this by adding a boolean argument to the backref walk context
structure to indicate that the inode extent list should not be built,
make relocation set that argument to true and fix the backref walking
logic to skip the calls to check_extent_in_eb() and find_extent_in_eb()
only if this new argument is true, instead of 'ignore_extent_item_pos'
being true.
A test case for fstests will be added soon, to provide cover not only
for these cases but to the logical to ino ioctl in general as well, as
currently we do not have a test case for it.
Reported-by: Vladimir Panteleev <git@vladimir.panteleev.md>
Link: https://lore.kernel.org/linux-btrfs/CAHhfkvwo=nmzrJSqZ2qMfF-rZB-ab6ahHnCD_sq9h4o8v+M7QQ@mail.gmail.com/
Fixes: 6ce6ba5344 ("btrfs: use a single argument for extent offset in backref walking functions")
CC: stable@vger.kernel.org # 6.2+
Tested-by: Vladimir Panteleev <git@vladimir.panteleev.md>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 02ca9e6fb5 upstream.
When both of the superblock zones are full, we need to check which
superblock is newer. The calculation of last superblock position is wrong
as it does not consider zone_capacity and uses the length.
Fixes: 9658b72ef3 ("btrfs: zoned: locate superblock position using zone capacity")
CC: stable@vger.kernel.org # 6.1+
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f84353c7c2 upstream.
For data block groups, we zone finish a zone (or, just deactivate it) when
seeing the last IO in btrfs_finish_ordered_io(). That is only called for
IOs using ZONE_APPEND, but we use a regular WRITE command for data
relocation IOs. Detect it and call btrfs_zone_finish_endio() properly.
Fixes: be1a1d7a5d ("btrfs: zoned: finish fully written block group")
CC: stable@vger.kernel.org # 6.1+
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0004ff15ea upstream.
When loading a free space cache from disk, at __load_free_space_cache(),
if we fail to insert a bitmap entry, we still increment the number of
total bitmaps in the btrfs_free_space_ctl structure, which is incorrect
since we failed to add the bitmap entry. On error we then empty the
cache by calling __btrfs_remove_free_space_cache(), which will result
in getting the total bitmaps counter set to 1.
A failure to load a free space cache is not critical, so if a failure
happens we just rebuild the cache by scanning the extent tree, which
happens at block-group.c:caching_thread(). Yet the failure will result
in having the total bitmaps of the btrfs_free_space_ctl always bigger
by 1 then the number of bitmap entries we have. So fix this by having
the total bitmaps counter be incremented only if we successfully added
the bitmap entry.
Fixes: a67509c300 ("Btrfs: add a io_ctl struct and helpers for dealing with the space cache")
Reviewed-by: Anand Jain <anand.jain@oracle.com>
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c87f318e6f upstream.
Check nodesize to sectorsize in alignment check in print_extent_item.
The comment states that and this is correct, similar check is done
elsewhere in the functions.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: ea57788eb7 ("btrfs: require only sector size alignment for parent eb bytenr")
CC: stable@vger.kernel.org # 4.14+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Anastasia Belova <abelova@astralinux.ru>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d6a4fc857 upstream.
Previously clear_cache mount option would simply disable free-space-tree
feature temporarily then re-enable it to rebuild the whole free space
tree.
But this is problematic for block-group-tree feature, as we have an
artificial dependency on free-space-tree feature.
If we go the existing method, after clearing the free-space-tree
feature, we would flip the filesystem to read-only mode, as we detect a
super block write with block-group-tree but no free-space-tree feature.
This patch would change the behavior by properly rebuilding the free
space tree without disabling this feature, thus allowing clear_cache
mount option to work with block group tree.
Now we can mount a filesystem with block-group-tree feature and
clear_mount option:
$ mkfs.btrfs -O block-group-tree /dev/test/scratch1 -f
$ sudo mount /dev/test/scratch1 /mnt/btrfs -o clear_cache
$ sudo dmesg -t | head -n 5
BTRFS info (device dm-1): force clearing of disk cache
BTRFS info (device dm-1): using free space tree
BTRFS info (device dm-1): auto enabling async discard
BTRFS info (device dm-1): rebuilding free space tree
BTRFS info (device dm-1): checking UUID tree
CC: stable@vger.kernel.org # 6.1+
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c83b56d1dd upstream.
btrfs_redirty_list_add zeroes the buffer data and sets the
EXTENT_BUFFER_NO_CHECK to make sure writeback is fine with a bogus
header. But it does that after already marking the buffer dirty, which
means that writeback could already be looking at the buffer.
Switch the order of operations around so that the buffer is only marked
dirty when we're ready to write it.
Fixes: d3575156f6 ("btrfs: zoned: redirty released extent buffers")
CC: stable@vger.kernel.org # 5.15+
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d246331b78 upstream.
Boris noticed in his simple quotas testing that he was getting a leak
with Sweet Tea's change to subvol create that stopped doing a
transaction commit. This was just a side effect of that change.
In the delayed inode code we have an optimization that will free extra
reservations if we think we can pack a dir item into an already modified
leaf. Previously this wouldn't be triggered in the subvolume create
case because we'd commit the transaction, it was still possible but
much harder to trigger. It could actually be triggered if we did a
mkdir && subvol create with qgroups enabled.
This occurs because in btrfs_insert_delayed_dir_index(), which gets
called when we're adding the dir item, we do the following:
btrfs_block_rsv_release(fs_info, trans->block_rsv, bytes, NULL);
if we're able to skip reserving space.
The problem here is that trans->block_rsv points at the temporary block
rsv for the subvolume create, which has qgroup reservations in the block
rsv.
This is a problem because btrfs_block_rsv_release() will do the
following:
if (block_rsv->qgroup_rsv_reserved >= block_rsv->qgroup_rsv_size) {
qgroup_to_release = block_rsv->qgroup_rsv_reserved -
block_rsv->qgroup_rsv_size;
block_rsv->qgroup_rsv_reserved = block_rsv->qgroup_rsv_size;
}
The temporary block rsv just has ->qgroup_rsv_reserved set,
->qgroup_rsv_size == 0. The optimization in
btrfs_insert_delayed_dir_index() sets ->qgroup_rsv_reserved = 0. Then
later on when we call btrfs_subvolume_release_metadata() which has
btrfs_block_rsv_release(fs_info, rsv, (u64)-1, &qgroup_to_release);
btrfs_qgroup_convert_reserved_meta(root, qgroup_to_release);
qgroup_to_release is set to 0, and we do not convert the reserved
metadata space.
The problem here is that the block rsv code has been unconditionally
messing with ->qgroup_rsv_reserved, because the main place this is used
is delalloc, and any time we call btrfs_block_rsv_release() we do it
with qgroup_to_release set, and thus do the proper accounting.
The subvolume code is the only other code that uses the qgroup
reservation stuff, but it's intermingled with the above optimization,
and thus was getting its reservation freed out from underneath it and
thus leaking the reserved space.
The solution is to simply not mess with the qgroup reservations if we
don't have qgroup_to_release set. This works with the existing code as
anything that messes with the delalloc reservations always have
qgroup_to_release set. This fixes the leak that Boris was observing.
Reviewed-by: Qu Wenruo <wqu@suse.com>
CC: stable@vger.kernel.org # 5.4+
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7db9e5c6b upstream.
We have observed a btrfs filesystem corruption on workloads using
no-holes and encoded writes via send stream v2. The symptom is that a
file appears to be truncated to the end of its last aligned extent, even
though the final unaligned extent and even the file extent and otherwise
correctly updated inode item have been written.
So if we were writing out a 1MiB+X file via 8 128K extents and one
extent of length X, i_size would be set to 1MiB, but the ninth extent,
nbyte, etc. would all appear correct otherwise.
The source of the race is a narrow (one line of code) window in which a
no-holes fs has read in an updated i_size, but has not yet set a shared
disk_i_size variable to write. Therefore, if two ordered extents run in
parallel (par for the course for receive workloads), the following
sequence can play out: (following "threads" a bit loosely, since there
are callbacks involved for endio but extra threads aren't needed to
cause the issue)
ENC-WR1 (second to last) ENC-WR2 (last)
------- -------
btrfs_do_encoded_write
set i_size = 1M
submit bio B1 ending at 1M
endio B1
btrfs_inode_safe_disk_i_size_write
local i_size = 1M
falls off a cliff for some reason
btrfs_do_encoded_write
set i_size = 1M+X
submit bio B2 ending at 1M+X
endio B2
btrfs_inode_safe_disk_i_size_write
local i_size = 1M+X
disk_i_size = 1M+X
disk_i_size = 1M
btrfs_delayed_update_inode
btrfs_delayed_update_inode
And the delayed inode ends up filled with nbytes=1M+X and isize=1M, and
writes respect i_size and present a corrupted file missing its last
extents.
Fix this by holding the inode lock in the no-holes case so that a thread
can't sneak in a write to disk_i_size that gets overwritten with an out
of date i_size.
Fixes: 41a2ee75aa ("btrfs: introduce per-inode file extent tree")
CC: stable@vger.kernel.org # 5.10+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Boris Burkov <boris@bur.io>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 64b5d5b285 upstream.
[BUG]
With block-group-tree feature enabled, mounting it with clear_cache
would cause the following transaction abort at mount or remount:
BTRFS info (device dm-4): force clearing of disk cache
BTRFS info (device dm-4): using free space tree
BTRFS info (device dm-4): auto enabling async discard
BTRFS info (device dm-4): clearing free space tree
BTRFS info (device dm-4): clearing compat-ro feature flag for FREE_SPACE_TREE (0x1)
BTRFS info (device dm-4): clearing compat-ro feature flag for FREE_SPACE_TREE_VALID (0x2)
BTRFS error (device dm-4): block-group-tree feature requires fres-space-tree and no-holes
BTRFS error (device dm-4): super block corruption detected before writing it to disk
BTRFS: error (device dm-4) in write_all_supers:4288: errno=-117 Filesystem corrupted (unexpected superblock corruption detected)
BTRFS warning (device dm-4: state E): Skipping commit of aborted transaction.
[CAUSE]
For block-group-tree feature, we have an artificial dependency on
free-space-tree.
This means if we detect block-group-tree without v2 cache, we consider
it a corruption and cause the problem.
For clear_cache mount option, it would temporary disable v2 cache, then
re-enable it.
But unfortunately for that temporary v2 cache disabled status, we refuse
to write a superblock with bg tree only flag, thus leads to the above
transaction abortion.
[FIX]
For now, just reject clear_cache and v1 cache mount option for block
group tree. So now we got a graceful rejection other than a transaction
abort:
BTRFS info (device dm-4): force clearing of disk cache
BTRFS error (device dm-4): cannot disable free space tree with block-group-tree feature
BTRFS error (device dm-4): open_ctree failed
CC: stable@vger.kernel.org # 6.1+
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 631003e233 upstream.
find_next_bit and find_next_zero_bit take @size as the second parameter and
@offset as the third parameter. They are specified opposite in
btrfs_ensure_empty_zones(). Thanks to the later loop, it never failed to
detect the empty zones. Fix them and (maybe) return the result a bit
faster.
Note: the naming is a bit confusing, size has two meanings here, bitmap
and our range size.
Fixes: 1cd6121f2a ("btrfs: zoned: implement zoned chunk allocator")
CC: stable@vger.kernel.org # 5.15+
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f932d4ef0 upstream.
A call to btrfs_prev_leaf() may end up returning a path that points to the
same item (key) again. This happens if while btrfs_prev_leaf(), after we
release the path, a concurrent insertion happens, which moves items off
from a sibling into the front of the previous leaf, and an item with the
computed previous key does not exists.
For example, suppose we have the two following leaves:
Leaf A
-------------------------------------------------------------
| ... key (300 96 10) key (300 96 15) key (300 96 16) |
-------------------------------------------------------------
slot 20 slot 21 slot 22
Leaf B
-------------------------------------------------------------
| key (300 96 20) key (300 96 21) key (300 96 22) ... |
-------------------------------------------------------------
slot 0 slot 1 slot 2
If we call btrfs_prev_leaf(), from btrfs_previous_item() for example, with
a path pointing to leaf B and slot 0 and the following happens:
1) At btrfs_prev_leaf() we compute the previous key to search as:
(300 96 19), which is a key that does not exists in the tree;
2) Then we call btrfs_release_path() at btrfs_prev_leaf();
3) Some other task inserts a key at leaf A, that sorts before the key at
slot 20, for example it has an objectid of 299. In order to make room
for the new key, the key at slot 22 is moved to the front of leaf B.
This happens at push_leaf_right(), called from split_leaf().
After this leaf B now looks like:
--------------------------------------------------------------------------------
| key (300 96 16) key (300 96 20) key (300 96 21) key (300 96 22) ... |
--------------------------------------------------------------------------------
slot 0 slot 1 slot 2 slot 3
4) At btrfs_prev_leaf() we call btrfs_search_slot() for the computed
previous key: (300 96 19). Since the key does not exists,
btrfs_search_slot() returns 1 and with a path pointing to leaf B
and slot 1, the item with key (300 96 20);
5) This makes btrfs_prev_leaf() return a path that points to slot 1 of
leaf B, the same key as before it was called, since the key at slot 0
of leaf B (300 96 16) is less than the computed previous key, which is
(300 96 19);
6) As a consequence btrfs_previous_item() returns a path that points again
to the item with key (300 96 20).
For some users of btrfs_prev_leaf() or btrfs_previous_item() this may not
be functional a problem, despite not making sense to return a new path
pointing again to the same item/key. However for a caller such as
tree-log.c:log_dir_items(), this has a bad consequence, as it can result
in not logging some dir index deletions in case the directory is being
logged without holding the inode's VFS lock (logging triggered while
logging a child inode for example) - for the example scenario above, in
case the dir index keys 17, 18 and 19 were deleted in the current
transaction.
CC: stable@vger.kernel.org # 4.14+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a48d60467 upstream.
SYM_FUNC_START_LOCAL_NOALIGN() adds an endbr leading to this layout
(leaving only the last 2 bytes of the address):
3bff <zen_untrain_ret>:
3bff: f3 0f 1e fa endbr64
3c03: f6 test $0xcc,%bl
3c04 <__x86_return_thunk>:
3c04: c3 ret
3c05: cc int3
3c06: 0f ae e8 lfence
However, "the RET at __x86_return_thunk must be on a 64 byte boundary,
for alignment within the BTB."
Use SYM_START instead.
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cf9f4c0eb1 ]
Refresh the MMU's snapshot of the vCPU's CR0.WP prior to checking for
permission faults when emulating a guest memory access and CR0.WP may be
guest owned. If the guest toggles only CR0.WP and triggers emulation of
a supervisor write, e.g. when KVM is emulating UMIP, KVM may consume a
stale CR0.WP, i.e. use stale protection bits metadata.
Note, KVM passes through CR0.WP if and only if EPT is enabled as CR0.WP
is part of the MMU role for legacy shadow paging, and SVM (NPT) doesn't
support per-bit interception controls for CR0. Don't bother checking for
EPT vs. NPT as the "old == new" check will always be true under NPT, i.e.
the only cost is the read of vcpu->arch.cr4 (SVM unconditionally grabs CR0
from the VMCB on VM-Exit).
Reported-by: Mathias Krause <minipli@grsecurity.net>
Link: https://lkml.kernel.org/r/677169b4-051f-fcae-756b-9a3e1bb9f8fe%40grsecurity.net
Fixes: fb509f76ac ("KVM: VMX: Make CR0.WP a guest owned bit")
Tested-by: Mathias Krause <minipli@grsecurity.net>
Link: https://lore.kernel.org/r/20230405002608.418442-1-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Mathias Krause <minipli@grsecurity.net> # backport to v6.3.x
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb509f76ac ]
Guests like grsecurity that make heavy use of CR0.WP to implement kernel
level W^X will suffer from the implied VMEXITs.
With EPT there is no need to intercept a guest change of CR0.WP, so
simply make it a guest owned bit if we can do so.
This implies that a read of a guest's CR0.WP bit might need a VMREAD.
However, the only potentially affected user seems to be kvm_init_mmu()
which is a heavy operation to begin with. But also most callers already
cache the full value of CR0 anyway, so no additional VMREAD is needed.
The only exception is nested_vmx_load_cr3().
This change is VMX-specific, as SVM has no such fine grained control
register intercept control.
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Mathias Krause <minipli@grsecurity.net>
Link: https://lore.kernel.org/r/20230322013731.102955-7-minipli@grsecurity.net
Co-developed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Mathias Krause <minipli@grsecurity.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 01b31714bd ]
There is no need to unload the MMU roots with TDP enabled when only
CR0.WP has changed -- the paging structures are still valid, only the
permission bitmap needs to be updated.
One heavy user of toggling CR0.WP is grsecurity's KERNEXEC feature to
implement kernel W^X.
The optimization brings a huge performance gain for this case as the
following micro-benchmark running 'ssdd 10 50000' from rt-tests[1] on a
grsecurity L1 VM shows (runtime in seconds, lower is better):
legacy TDP shadow
kvm-x86/next@d8708b 8.43s 9.45s 70.3s
+patch 5.39s 5.63s 70.2s
For legacy MMU this is ~36% faster, for TDP MMU even ~40% faster. Also
TDP and legacy MMU now both have a similar runtime which vanishes the
need to disable TDP MMU for grsecurity.
Shadow MMU sees no measurable difference and is still slow, as expected.
[1] https://git.kernel.org/pub/scm/utils/rt-tests/rt-tests.git
Signed-off-by: Mathias Krause <minipli@grsecurity.net>
Link: https://lore.kernel.org/r/20230322013731.102955-3-minipli@grsecurity.net
Co-developed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Mathias Krause <minipli@grsecurity.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ecc68ee216 ]
It seems that perf stat -b <prog id> doesn't produce any results:
$ perf stat -e cycles -b 4 -I 10000 -vvv
Control descriptor is not initialized
cycles: 0 0 0
time counts unit events
10.007641640 <not supported> cycles
Looks like this happens because fentry/fexit progs are getting loaded, but the
corresponding perf event is not enabled and not added into the events bpf map.
I think there is some mixing up between two type of bpf support, one for bperf
and one for bpf_profiler. Both are identified via evsel__is_bpf, based on which
perf events are enabled, but for the latter (bpf_profiler) a perf event is
required. Using evsel__is_bperf to check only bperf produces expected results:
$ perf stat -e cycles -b 4 -I 10000 -vvv
Control descriptor is not initialized
------------------------------------------------------------
perf_event_attr:
size 136
sample_type IDENTIFIER
read_format TOTAL_TIME_ENABLED|TOTAL_TIME_RUNNING
disabled 1
exclude_guest 1
------------------------------------------------------------
sys_perf_event_open: pid -1 cpu 0 group_fd -1 flags 0x8 = 3
------------------------------------------------------------
[...perf_event_attr for other CPUs...]
------------------------------------------------------------
cycles: 309426 169009 169009
time counts unit events
10.010091271 309426 cycles
The final numbers correspond (at least in the level of magnitude) to the
same metric obtained via bpftool.
Fixes: 112cb56164 ("perf stat: Introduce config stat.bpf-counter-events")
Reviewed-by: Song Liu <song@kernel.org>
Signed-off-by: Dmitrii Dolgov <9erthalion6@gmail.com>
Tested-by: Song Liu <song@kernel.org>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230412182316.11628-1-9erthalion6@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4140aafcff ]
CRYPTO_TFM_REQ_MAY_BACKLOG tells the crypto driver that it should
internally backlog requests until the crypto hw's queue becomes
full. At that point, crypto_engine backlogs the request and returns
-EBUSY. Calling driver such as dm-crypt then waits until the
complete() function is called with a status of -EINPROGRESS before
sending a new request.
The problem lies in the call to complete() with a value of -EINPROGRESS
that is made when a backlog item is present on the queue. The call is
done before the successful execution of the crypto request. In the case
that do_one_request() returns < 0 and the retry support is available,
the request is put back in the queue. This leads upper drivers to send
a new request even if the queue is still full.
The problem can be reproduced by doing a large dd into a crypto
dm-crypt device. This is pretty easy to see when using
Freescale CAAM crypto driver and SWIOTLB dma. Since the actual amount
of requests that can be hold in the queue is unlimited we get IOs error
and dma allocation.
The fix is to call complete with a value of -EINPROGRESS only if
the request is not enqueued back in crypto_queue. This is done
by calling complete() later in the code. In order to delay the decision,
crypto_queue is modified to correctly set the backlog pointer
when a request is enqueued back.
Fixes: 6a89f492f8 ("crypto: engine - support for parallel requests based on retry mechanism")
Co-developed-by: Sylvain Ouellet <souellet@genetec.com>
Signed-off-by: Sylvain Ouellet <souellet@genetec.com>
Signed-off-by: Olivier Bacon <obacon@genetec.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8fd91151eb ]
SS_ENCRYPTION is (0 << 7 = 0), so the test can never be true.
Use a direct comparison to SS_ENCRYPTION instead.
The same king of test is already done the same way in sun8i_ss_run_task().
Fixes: 359e893e8a ("crypto: sun8i-ss - rework handling of IV")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57f14b5ae1 ]
An audit showed just this one problem with zfree(), fix it.
Fixes: 9fbc61f832 ("perf pmu: Add support for PMU capabilities")
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07d85ba9d0 ]
Hundreds of "read LOST count failed" error messages may be displayed,
when the below command is launched.
perf record -e '{cpu/mem-loads-aux/,cpu/event=0xcd,umask=0x1/}:S' -a
According to the commit 89e3106fa2 ("libperf: Handle read format
in perf_evsel__read()"), the PERF_FORMAT_GROUP is only available for
the leader. However, the record__read_lost_samples() goes through every
entry of an evlist, which includes both leader and member. The member
event errors out and triggers the error message. Since there may be
hundreds of CPUs on a server, the message will be printed hundreds of
times, which is very annoying.
The message itself is correct, but the pr_err is a overkill. Other error
messages in the record__read_lost_samples() are all pr_debug. To make
the output format consistent, change the pr_err("read LOST count
failed\n"); to pr_debug("read LOST count failed\n");.
User can still get the message via -v option.
Fixes: e3a23261ad ("perf record: Read and inject LOST_SAMPLES events")
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20230301150413.27011-1-kan.liang@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd741f0d9f ]
When replacing a filter (i.e. 'fold' pointer is not NULL) the insertion of
new filter to idr is postponed until later in code since handle is already
provided by the user. However, the error handling code in fl_change()
always assumes that the new filter had been inserted into idr. If error
handler is reached when replacing existing filter it may remove it from idr
therefore making it unreachable for delete or dump afterwards. Fix the
issue by verifying that 'fold' argument wasn't provided by caller before
calling idr_remove().
Fixes: 08a0063df3 ("net/sched: flower: Move filter handle initialization earlier")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Pedro Tammela <pctammela@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26312c685a ]
In the current xdp_xmit implementation, if any single frame fails to
transmit due to insufficient buffer descriptors, the function nevertheless
reports success in sending all frames. This results in erroneously
indicating that frames were transmitted when in fact they were dropped.
This patch fixes the issue by ensureing the return value properly
indicates the actual number of frames successfully transmitted, rather than
potentially reporting success for all frames when some could not transmit.
Fixes: 6d6b39f180 ("net: fec: add initial XDP support")
Signed-off-by: Gagandeep Singh <g.singh@nxp.com>
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 299efdc238 ]
We should check whether the current SFI (Stream Filter Instance) table
is full before creating a new SFI entry. However, the previous logic
checks the handle by mistake and might lead to unpredictable behavior.
Fixes: 888ae5a395 ("net: enetc: add tc flower psfp offload driver")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8bb510439 ]
For multi-queue and large ring-size use case, the following error
occurred when free_unused_bufs:
rcu: INFO: rcu_sched self-detected stall on CPU.
Fixes: 986a4f4d45 ("virtio_net: multiqueue support")
Signed-off-by: Wenliang Wang <wangwenliang.1995@bytedance.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 120a56b01b ]
On mt753x_cpu_port_enable() there's code that enables flooding for the CPU
port only. Since mt753x_cpu_port_enable() runs twice when both CPU ports
are enabled, port 6 becomes the only port to forward the frames to. But
port 5 is the active port, so no frames received from the user ports will
be forwarded to port 5 which breaks network connectivity.
Every bit of the BC_FFP, UNM_FFP, and UNU_FFP bits represents a port. Fix
this issue by setting the bit that corresponds to the CPU port without
overwriting the other bits.
Clear the bits beforehand only for the MT7531 switch. According to the
documents MT7621 Giga Switch Programming Guide v0.3 and MT7531 Reference
Manual for Development Board v1.0, after reset, the BC_FFP, UNM_FFP, and
UNU_FFP bits are set to 1 for MT7531, 0 for MT7530.
The commit 5e5502e012 ("net: dsa: mt7530: fix roaming from DSA user
ports") silently changed the method to set the bits on the MT7530_MFC.
Instead of clearing the relevant bits before mt7530_cpu_port_enable()
which runs under a for loop, the commit started doing it on
mt7530_cpu_port_enable().
Back then, this didn't really matter as only a single CPU port could be
used since the CPU port number was hardcoded. The driver was later changed
with commit 1f9a6abecf ("net: dsa: mt7530: get cpu-port via dp->cpu_dp
instead of constant") to retrieve the CPU port via dp->cpu_dp. With that,
this silent change became an issue for when using multiple CPU ports.
Fixes: 5e5502e012 ("net: dsa: mt7530: fix roaming from DSA user ports")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f54cc9772 ]
MT7988 shares a significant part of the setup function with MT7531.
Split-off those parts into a shared function which is going to be used
also by mt7988_setup.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 120a56b01b ("net: dsa: mt7530: fix network connectivity with multiple CPU ports")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37c218d802 ]
The multi-chip module MT7530 switch with a 40 MHz oscillator on the
MT7621AT, MT7621DAT, and MT7621ST SoCs forwards corrupt frames using
trgmii.
This is caused by the assumption that MT7621 SoCs have got 150 MHz PLL,
hence using the ncpo1 value, 0x0780.
My testing shows this value works on Unielec U7621-06, Bartel's testing
shows it won't work on Hi-Link HLK-MT7621A and Netgear WAC104. All devices
tested have got 40 MHz oscillators.
Using the value for 125 MHz PLL, 0x0640, works on all boards at hand. The
definitions for 125 MHz PLL exist on the Banana Pi BPI-R2 BSP source code
whilst 150 MHz PLL don't.
Forwarding frames using trgmii on the MCM MT7530 switch with a 25 MHz
oscillator on the said MT7621 SoCs works fine because the ncpo1 value
defined for it is for 125 MHz PLL.
Change the 150 MHz PLL comment to 125 MHz PLL, and use the 125 MHz PLL
ncpo1 values for both oscillator frequencies.
Link: 81d24bbce7/u-boot-mt/drivers/net/rt2880_eth.c (L2195)
Fixes: 7ef6f6f8d2 ("net: dsa: mt7530: Add MT7621 TRGMII mode support")
Tested-by: Bartel Eerdekens <bartel.eerdekens@constell8.be>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d276e4d3b ]
Seemingly I mis-implemented the dependencies here. The OpenSBI docs only
point out that the "riscv,event-to-mhpmcounters property is mandatory if
riscv,event-to-mhpmevent is present". It never claims that
riscv,event-to-mhpmcounters requires riscv,event-to-mhpmevent.
Drop the dependency of riscv,event-to-mhpmcounters on
riscv,event-to-mhpmevent.
Fixes: 7e38085d9c ("dt-bindings: riscv: add SBI PMU event mappings")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Link: https://lore.kernel.org/r/20230404-tractor-confusing-8852e552539a@spud
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c148dc8e2f ]
Fix a potential race in gmap_make_secure() and remove the last user of
follow_page() without FOLL_GET.
The old code is locking something it doesn't have a reference to, and
as explained by Jason and David in this discussion:
https://lore.kernel.org/linux-mm/Y9J4P%2FRNvY1Ztn0Q@nvidia.com/
it can lead to all kind of bad things, including the page getting
unmapped (MADV_DONTNEED), freed, reallocated as a larger folio and the
unlock_page() would target the wrong bit.
There is also another race with the FOLL_WRITE, which could race
between the follow_page() and the get_locked_pte().
The main point is to remove the last use of follow_page() without
FOLL_GET or FOLL_PIN, removing the races can be considered a nice
bonus.
Link: https://lore.kernel.org/linux-mm/Y9J4P%2FRNvY1Ztn0Q@nvidia.com/
Suggested-by: Jason Gunthorpe <jgg@nvidia.com>
Fixes: 214d9bbcd3 ("s390/mm: provide memory management functions for protected KVM guests")
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Message-Id: <20230428092753.27913-2-imbrenda@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 292a7d6fca ]
On machines without the Destroy Secure Configuration Fast UVC, the
topmost level of page tables is set aside and freed asynchronously
as last step of the asynchronous teardown.
Each gmap has a host_to_guest radix tree mapping host (userspace)
addresses (with 1M granularity) to gmap segment table entries (pmds).
If a guest is smaller than 2GB, the topmost level of page tables is the
segment table (i.e. there are only 2 levels). Replacing it means that
the pointers in the host_to_guest mapping would become stale and cause
all kinds of nasty issues.
This patch fixes the issue by disallowing asynchronous teardown for
guests with only 2 levels of page tables. Userspace should (and already
does) try using the normal destroy if the asynchronous one fails.
Update s390_replace_asce so it refuses to replace segment type ASCEs.
This is still needed in case the normal destroy VM fails.
Fixes: fb491d5500 ("KVM: s390: pv: asynchronous destroy for reboot")
Reviewed-by: Marc Hartmayer <mhartmay@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Message-Id: <20230421085036.52511-2-imbrenda@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d727e1856 ]
Smatch complains that:
snd_usb_caiaq_input_init() warn: missing error code 'ret'
This patch adds a new case to handle the situation where the
device does not support any input methods in the
`snd_usb_caiaq_input_init` function. It returns an `-EINVAL` error code
to indicate that no input methods are supported on the device.
Fixes: 523f1dce37 ("[ALSA] Add Native Instrument usb audio device support")
Signed-off-by: Ruliang Lin <u202112092@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Acked-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20230504065054.3309-1-u202112092@hust.edu.cn
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2397e3d8d2 ]
mgr->ctx_handles should be protected by mgr->lock.
v2: improve commit message
v3: add a Fixes tag
Signed-off-by: Chia-I Wu <olvaffe@gmail.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Fixes: 52c6a62c64 ("drm/amdgpu: add interface for editing a foreign process's priority v3")
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0b79b0ff5 ]
Add timeout handler, so that we can provide forward progress guarantee for
unprivileged ublk, which can't be trusted.
One thing is that sync() calls sync_bdevs(wait) for all block devices after
running sync_bdevs(no_wait), and if one device can't move on, the sync() won't
return any more.
Add timeout for unprivileged ublk to avoid such affect for other users which call
sync() syscall.
Meantime clear UBLK_F_USER_RECOVERY_REISSUE for unprivileged ublk since
that feature may cause IO hang too.
Fixes: 4093cb5a06 ("ublk_drv: add mechanism for supporting unprivileged ublk device")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230502024231.888498-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d388143fa ]
The gxp_i2c_slave_irq_handler() is hidden in an #ifdef, but the
caller uses an IS_ENABLED() check:
drivers/i2c/busses/i2c-gxp.c: In function 'gxp_i2c_irq_handler':
drivers/i2c/busses/i2c-gxp.c:467:29: error: implicit declaration of function 'gxp_i2c_slave_irq_handler'; did you mean 'gxp_i2c_irq_handler'? [-Werror=implicit-function-declaration]
It has to consistently use one method or the other to avoid warnings,
so move to IS_ENABLED() here for readability and build coverage, and
move the #ifdef in linux/i2c.h to allow building it as dead code.
Fixes: 4a55ed6f89 ("i2c: Add GXP SoC I2C Controller")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nick Hawkins <nick.hawkins@hpe.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a54903ff6 ]
Add a check for NULL on the alloc return. If devlink_alloc() fails and
we try to use devlink_priv() on the NULL return, the kernel gets very
unhappy and panics. With this fix, the driver load will still fail,
but at least it won't panic the kernel.
Fixes: df69ba4321 ("ionic: Add basic framework for IONIC Network device driver")
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ad685dbfe ]
It is not possible to set the number of lanes when setting link modes
using the legacy IOCTL ethtool interface. Since 'struct
ethtool_link_ksettings' is not initialized in this path, drivers receive
an uninitialized number of lanes in 'struct
ethtool_link_ksettings::lanes'.
When this information is later queried from drivers, it results in the
ethtool code making decisions based on uninitialized memory, leading to
the following KMSAN splat [1]. In practice, this most likely only
happens with the tun driver that simply returns whatever it got in the
set operation.
As far as I can tell, this uninitialized memory is not leaked to user
space thanks to the 'ethtool_ops->cap_link_lanes_supported' check in
linkmodes_prepare_data().
Fix by initializing the structure in the IOCTL path. Did not find any
more call sites that pass an uninitialized structure when calling
'ethtool_ops::set_link_ksettings()'.
[1]
BUG: KMSAN: uninit-value in ethnl_update_linkmodes net/ethtool/linkmodes.c:273 [inline]
BUG: KMSAN: uninit-value in ethnl_set_linkmodes+0x190b/0x19d0 net/ethtool/linkmodes.c:333
ethnl_update_linkmodes net/ethtool/linkmodes.c:273 [inline]
ethnl_set_linkmodes+0x190b/0x19d0 net/ethtool/linkmodes.c:333
ethnl_default_set_doit+0x88d/0xde0 net/ethtool/netlink.c:640
genl_family_rcv_msg_doit net/netlink/genetlink.c:968 [inline]
genl_family_rcv_msg net/netlink/genetlink.c:1048 [inline]
genl_rcv_msg+0x141a/0x14c0 net/netlink/genetlink.c:1065
netlink_rcv_skb+0x3f8/0x750 net/netlink/af_netlink.c:2577
genl_rcv+0x40/0x60 net/netlink/genetlink.c:1076
netlink_unicast_kernel net/netlink/af_netlink.c:1339 [inline]
netlink_unicast+0xf41/0x1270 net/netlink/af_netlink.c:1365
netlink_sendmsg+0x127d/0x1430 net/netlink/af_netlink.c:1942
sock_sendmsg_nosec net/socket.c:724 [inline]
sock_sendmsg net/socket.c:747 [inline]
____sys_sendmsg+0xa24/0xe40 net/socket.c:2501
___sys_sendmsg+0x2a1/0x3f0 net/socket.c:2555
__sys_sendmsg net/socket.c:2584 [inline]
__do_sys_sendmsg net/socket.c:2593 [inline]
__se_sys_sendmsg net/socket.c:2591 [inline]
__x64_sys_sendmsg+0x36b/0x540 net/socket.c:2591
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Uninit was stored to memory at:
tun_get_link_ksettings+0x37/0x60 drivers/net/tun.c:3544
__ethtool_get_link_ksettings+0x17b/0x260 net/ethtool/ioctl.c:441
ethnl_set_linkmodes+0xee/0x19d0 net/ethtool/linkmodes.c:327
ethnl_default_set_doit+0x88d/0xde0 net/ethtool/netlink.c:640
genl_family_rcv_msg_doit net/netlink/genetlink.c:968 [inline]
genl_family_rcv_msg net/netlink/genetlink.c:1048 [inline]
genl_rcv_msg+0x141a/0x14c0 net/netlink/genetlink.c:1065
netlink_rcv_skb+0x3f8/0x750 net/netlink/af_netlink.c:2577
genl_rcv+0x40/0x60 net/netlink/genetlink.c:1076
netlink_unicast_kernel net/netlink/af_netlink.c:1339 [inline]
netlink_unicast+0xf41/0x1270 net/netlink/af_netlink.c:1365
netlink_sendmsg+0x127d/0x1430 net/netlink/af_netlink.c:1942
sock_sendmsg_nosec net/socket.c:724 [inline]
sock_sendmsg net/socket.c:747 [inline]
____sys_sendmsg+0xa24/0xe40 net/socket.c:2501
___sys_sendmsg+0x2a1/0x3f0 net/socket.c:2555
__sys_sendmsg net/socket.c:2584 [inline]
__do_sys_sendmsg net/socket.c:2593 [inline]
__se_sys_sendmsg net/socket.c:2591 [inline]
__x64_sys_sendmsg+0x36b/0x540 net/socket.c:2591
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Uninit was stored to memory at:
tun_set_link_ksettings+0x37/0x60 drivers/net/tun.c:3553
ethtool_set_link_ksettings+0x600/0x690 net/ethtool/ioctl.c:609
__dev_ethtool net/ethtool/ioctl.c:3024 [inline]
dev_ethtool+0x1db9/0x2a70 net/ethtool/ioctl.c:3078
dev_ioctl+0xb07/0x1270 net/core/dev_ioctl.c:524
sock_do_ioctl+0x295/0x540 net/socket.c:1213
sock_ioctl+0x729/0xd90 net/socket.c:1316
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:870 [inline]
__se_sys_ioctl+0x222/0x400 fs/ioctl.c:856
__x64_sys_ioctl+0x96/0xe0 fs/ioctl.c:856
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Local variable link_ksettings created at:
ethtool_set_link_ksettings+0x54/0x690 net/ethtool/ioctl.c:577
__dev_ethtool net/ethtool/ioctl.c:3024 [inline]
dev_ethtool+0x1db9/0x2a70 net/ethtool/ioctl.c:3078
Fixes: 012ce4dd31 ("ethtool: Extend link modes settings uAPI with lanes")
Reported-and-tested-by: syzbot+ef6edd9f1baaa54d6235@syzkaller.appspotmail.com
Link: https://lore.kernel.org/netdev/0000000000004bb41105fa70f361@google.com/
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0fbd79c01a ]
Set supports_autosuspend = 1 for the rtl8152_cfgselector_driver.
Fixes: ec51fbd1b8 ("r8152: add USB device driver for config selection")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3711d44fac ]
It seems that ethtool is calling into .get_rxnfc more often with
ETHTOOL_GRXCLSRLCNT which ionic doesn't know about. We don't
need to log a message about it, just return not supported.
Fixes: aa3198819b ("ionic: Add RSS support")
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99ae1260fd ]
When a VF device probe fails due to error in MSIX vector allocation then
the resources NIX and NPA LFs were not detached. Fix this by detaching
the LFs when MSIX vector allocation fails.
Fixes: 3184fb5ba9 ("octeontx2-vf: Virtual function driver support")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c926252205 ]
At the stage of enabling packet I/O in otx2_open, If mailbox
timeout occurs then interface ends up in down state where as
hardware packet I/O is enabled. Hence disable packet I/O also
before bailing out.
Fixes: 1ea0166da0 ("octeontx2-pf: Fix the device state on error")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5eb1b72209 ]
Firmware enables PFs and allocate mbox resources for each of the PFs.
Currently PF driver configures mbox resources without checking whether
PF is enabled or not. This results in crash. This patch fixes this issue
by skipping disabled PF's mbox initialization.
Fixes: 9bdc47a6e3 ("octeontx2-af: Mbox communication support btw AF and it's VFs")
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f661559059 ]
1. Allow field hash configuration for both source and destination IPv6.
2. Configure hardware parser based on hash extract feature enable flag
for IPv6.
3. Fix IPv6 endianness issue while updating the source/destination IP
address via ntuple rule.
Fixes: 56d9f5fd22 ("octeontx2-af: Use hashed field in MCAM key")
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 406bed11fb ]
1. As per previous implementation, mask and control parameter to
generate the field hash value was not passed to the caller program.
Updated the secret key mbox to share that information as well,
as a part of the fix.
2. Earlier implementation did not consider hash reduction of both
source and destination IPv6 addresses. Only source IPv6 address
was considered. This fix solves that and provides option to hash
Fixes: 56d9f5fd22 ("octeontx2-af: Use hashed field in MCAM key")
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2075bf150d ]
During the initial design, the IPv4 ip_flag mask was set to 0xff.
Which results to filter only fragmets with (fragment_offset == 0).
As part of the fix, updated the mask to 0x20 to filter all the
fragmented packets irrespective of the fragment_offset value.
Fixes: c672e37279 ("octeontx2-pf: Add support to filter packet based on IP fragment")
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb5edce271 ]
Upon physical link change, firmware reports to the kernel about the
change along with the details like speed, lmac_type_id, etc.
Kernel derives lmac_type based on lmac_type_id received from firmware.
In a few scenarios, firmware returns an invalid lmac_type_id, which
is resulting in below kernel panic. This patch adds the missing
validation of the lmac_type_id field.
Internal error: Oops: 96000005 [#1] PREEMPT SMP
[ 35.321595] Modules linked in:
[ 35.328982] CPU: 0 PID: 31 Comm: kworker/0:1 Not tainted
5.4.210-g2e3169d8e1bc-dirty #17
[ 35.337014] Hardware name: Marvell CN103XX board (DT)
[ 35.344297] Workqueue: events work_for_cpu_fn
[ 35.352730] pstate: 40400089 (nZcv daIf +PAN -UAO)
[ 35.360267] pc : strncpy+0x10/0x30
[ 35.366595] lr : cgx_link_change_handler+0x90/0x180
Fixes: 61071a871e ("octeontx2-af: Forward CGX link notifications to PFs")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c60a6b90e7 ]
In the current driver, NPC exact match feature was not getting
enabled as configured bit was not read properly.
for_each_set_bit_from() need end bit as one bit post
position in the bit map to read NPC exact nibble enable
bits properly. This patch fixes the same.
Fixes: b747923aff ("octeontx2-af: Exact match support")
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 048486f81d ]
APR table contains the lmtst base address of PF/VFs. These entries
are updated by the PF/VF during the device probe. The lmtst address
is fetched from HW using "TXN_REQ" and "ADDR_RSP_STS" registers.
The lock tries to protect these registers from getting overwritten
when multiple PFs invokes rvu_get_lmtaddr() simultaneously.
For example, if PF1 submit the request and got permitted before it
reads the response and PF2 got scheduled submit the request then the
response of PF1 is overwritten by the PF2 response.
Fixes: 893ae97214 ("octeontx2-af: cn10k: Support configurable LMTST regions")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8509f62b0b ]
If user does not specify hook number and priority, then assume this is
a chain/flowtable update. Therefore, report ENOENT which provides a
better hint than EINVAL. Set on extended netlink error report to refer
to the chain name.
Fixes: 5b6743fb2c ("netfilter: nf_tables: skip flowtable hooknum and priority on device updates")
Fixes: 5efe72698a97 ("netfilter: nf_tables: support for adding new devices to an existing netdev chain")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b9703ed44f ]
This patch allows users to add devices to an existing netdev chain.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Stable-dep-of: 8509f62b0b ("netfilter: nf_tables: hit ENOENT on unexisting chain/flowtable update with missing attributes")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3c060adc0 ]
Flowtable and netdev chains are bound to one or several netdevice,
extend netlink error reporting to specify the the netdevice that
triggers the error.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Stable-dep-of: 8509f62b0b ("netfilter: nf_tables: hit ENOENT on unexisting chain/flowtable update with missing attributes")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c6d96df9fa ]
Through testing I found out that hardware vlan rx offload support seems to
have some hardware issues. At least when using multiple MACs and when
receiving tagged packets on the secondary MAC, the hardware can sometimes
start to emit wrong tags on the first MAC as well.
In order to avoid such issues, drop the feature configuration and use
the offload feature only for DSA hardware untagging on MT7621/MT7622
devices where this feature works properly.
Fixes: 08666cbb7d ("net: ethernet: mtk_eth_soc: add support for configuring vlan rx offload")
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20230426172153.8352-1-linux@fw-web.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4df69e0df2 ]
commit d54170812e ("arm64: fix .idmap.text assertion for large kernels")
modified some of the section assembler directives that declare
.idmap.text to be SHF_ALLOC instead of
SHF_ALLOC|SHF_WRITE|SHF_EXECINSTR.
This patch fixes up the remaining stragglers that were left behind. Add
Fixes tag so that this doesn't precede related change in stable.
Fixes: d54170812e ("arm64: fix .idmap.text assertion for large kernels")
Reported-by: Greg Thelen <gthelen@google.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20230428-awx-v2-1-b197ffa16edc@google.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db099c625b ]
afs_make_call() calls rxrpc_kernel_begin_call() to begin a call (which may
get stalled in the background waiting for a connection to become
available); it then calls rxrpc_kernel_set_max_life() to set the timeouts -
but that starts the call timer so the call timer might then expire before
we get a connection assigned - leading to the following oops if the call
stalled:
BUG: kernel NULL pointer dereference, address: 0000000000000000
...
CPU: 1 PID: 5111 Comm: krxrpcio/0 Not tainted 6.3.0-rc7-build3+ #701
RIP: 0010:rxrpc_alloc_txbuf+0xc0/0x157
...
Call Trace:
<TASK>
rxrpc_send_ACK+0x50/0x13b
rxrpc_input_call_event+0x16a/0x67d
rxrpc_io_thread+0x1b6/0x45f
? _raw_spin_unlock_irqrestore+0x1f/0x35
? rxrpc_input_packet+0x519/0x519
kthread+0xe7/0xef
? kthread_complete_and_exit+0x1b/0x1b
ret_from_fork+0x22/0x30
Fix this by noting the timeouts in struct rxrpc_call when the call is
created. The timer will be started when the first packet is transmitted.
It shouldn't be possible to trigger this directly from userspace through
AF_RXRPC as sendmsg() will return EBUSY if the call is in the
waiting-for-conn state if it dropped out of the wait due to a signal.
Fixes: 9d35d880e0 ("rxrpc: Move client call connection to the I/O thread")
Reported-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: "David S. Miller" <davem@davemloft.net>
cc: Eric Dumazet <edumazet@google.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: linux-afs@lists.infradead.org
cc: netdev@vger.kernel.org
cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0eb362d254 ]
When sendmsg() creates an rxrpc call, it queues it to wait for a connection
and channel to be assigned and then waits before it can start shovelling
data as the encrypted DATA packet content includes a summary of the
connection parameters.
However, sendmsg() may get interrupted before a connection gets assigned
and further sendmsg() calls will fail with EBUSY until an assignment is
made.
Fix this so that the call can at least be aborted without failing on
EBUSY. We have to be careful here as sendmsg() mustn't be allowed to start
the call timer if the call doesn't yet have a connection assigned as an
oops may follow shortly thereafter.
Fixes: 540b1c48c3 ("rxrpc: Fix deadlock between call creation and sendmsg/recvmsg")
Reported-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: "David S. Miller" <davem@davemloft.net>
cc: Eric Dumazet <edumazet@google.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: linux-afs@lists.infradead.org
cc: netdev@vger.kernel.org
cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 281900a923 ]
The sfc driver does not report QSFP module EEPROM contents correctly
as only the first page is fetched from hardware.
Commit 0e1a2a3e6e ("ethtool: Add SFF-8436 and SFF-8636 max EEPROM
length definitions") added ETH_MODULE_SFF_8436_MAX_LEN for the overall
size of the EEPROM info, so use that to report the full EEPROM contents.
Fixes: 9b17010da5 ("sfc: Add ethtool -m support for QSFP modules")
Signed-off-by: Andy Moreton <andy.moreton@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cce8334f4a ]
Move setting r8153b_rx_agg_chg_indicate() for 2.5G devices. The
r8153b_rx_agg_chg_indicate() has to be called after enabling tx/rx.
Otherwise, the coalescing settings are useless.
Fixes: 195aae321c ("r8152: support new chips")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61b0ad6f58 ]
Fix the poor throughput for 2.5G devices, when changing the speed from
auto mode to force mode. This patch is used to notify the MAC when the
mode is changed.
Fixes: 195aae321c ("r8152: support new chips")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ceda6d5a1 ]
The feature of flow control becomes abnormal, if the device sends a
pause frame and the tx/rx is disabled before sending a release frame. It
causes the lost of packets.
Set PLA_RX_FIFO_FULL and PLA_RX_FIFO_EMPTY to zeros before disabling the
tx/rx. And, toggle FC_PATCH_TASK before enabling tx/rx to reset the flow
control patch and timer. Then, the hardware could clear the state and
the flow control becomes normal after enabling tx/rx.
Besides, remove inline for fc_pause_on_auto() and fc_pause_off_auto().
Fixes: 195aae321c ("r8152: support new chips")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 526f28bd0f ]
There are cases where the device is adminstratively UP, but operationally
down. For example, we have a physical device (Nvidia ConnectX-6 Dx, 25Gbps)
who's cable was pulled out, here is its ip link output:
5: ens2f1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN mode DEFAULT group default qlen 1000
link/ether b8:ce:f6:4b:68:35 brd ff:ff:ff:ff:ff:ff
altname enp179s0f1np1
As you can see, it's administratively UP but operationally down.
In this case, sending a packet to this port caused a nasty kernel hang (so
nasty that we were unable to capture it). Aborting a transmit based on
operational status (in addition to administrative status) fixes the issue.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Victor Nogueira <victor@mojatatu.com>
v1->v2: Add fixes tag
v2->v3: Remove blank line between tags + add change log, suggested by Leon
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f855779a3 ]
Update the msg->len value correctly for SMBUS block read. The discrepancy
went unnoticed as msg->len is used in SMBUS transfers only when a PEC
byte is added.
Fixes: d7583c8a57 ("i2c: tegra: Add SMBus block read function")
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8176080d59 ]
Kernel hang in blkg_destroy_all() when total blkg greater than
BLKG_DESTROY_BATCH_SIZE, because of not removing destroyed blkg in
blkg_list. So the size of blkg_list is same after destroying a
batch of blkg, and the infinite 'restart' occurs.
Since blkg should stay on the queue list until blkg_free_workfn(),
skip destroyed blkg when restart a new round, which will solve this
kernel hang issue and satisfy the previous will to restart.
Reported-by: Xiangfei Ma <xiangfeix.ma@intel.com>
Tested-by: Xiangfei Ma <xiangfeix.ma@intel.com>
Tested-by: Farrah Chen <farrah.chen@intel.com>
Signed-off-by: Tao Su <tao1.su@linux.intel.com>
Fixes: f1c006f1c6 ("blk-cgroup: synchronize pd_free_fn() from blkg_free_workfn() and blkcg_deactivate_policy()")
Suggested-and-reviewed-by: Yu Kuai <yukuai3@huawei.com>
Link: https://lore.kernel.org/r/20230428045149.1310073-1-tao1.su@linux.intel.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc6456e938 ]
The skb hash comes from sk->sk_txhash when using TCP, except for some
IPv6 RST packets. This is because in tcp_v6_send_reset when not in
TIME_WAIT the hash is taken from sk->sk_hash, while it should come from
sk->sk_txhash as those two hashes are not computed the same way.
Packetdrill script to test the above,
0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
+0 fcntl(3, F_SETFL, O_RDWR|O_NONBLOCK) = 0
+0 connect(3, ..., ...) = -1 EINPROGRESS (Operation now in progress)
+0 > (flowlabel 0x1) S 0:0(0) <...>
// Wrong ack seq, trigger a rst.
+0 < S. 0:0(0) ack 0 win 4000
// Check the flowlabel matches prior one from SYN.
+0 > (flowlabel 0x1) R 0:0(0) <...>
Fixes: 9258b8b1be ("ipv6: tcp: send consistent autoflowlabel in RST packets")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46ef24c60f ]
On some distributions, the rp_filter is automatically set (=1) by
default on a netdev basis (also on VRFs).
In an SRv6 End.DT46 behavior, decapsulated IPv4 packets are routed using
the table associated with the VRF bound to that tunnel. During lookup
operations, the rp_filter can lead to packet loss when activated on the
VRF.
Therefore, we chose to make this selftest more robust by explicitly
disabling the rp_filter during tests (as it is automatically set by some
Linux distributions).
Fixes: 03a0b567a0 ("selftests: seg6: add selftest for SRv6 End.DT46 Behavior")
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Tested-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e692df393 ]
David Ahern reported crashes in skb_copy_ubufs() caused by TCP tx zerocopy
using hugepages, and skb length bigger than ~68 KB.
skb_copy_ubufs() assumed it could copy all payload using up to
MAX_SKB_FRAGS order-0 pages.
This assumption broke when BIG TCP was able to put up to 512 KB per skb.
We did not hit this bug at Google because we use CONFIG_MAX_SKB_FRAGS=45
and limit gso_max_size to 180000.
A solution is to use higher order pages if needed.
v2: add missing __GFP_COMP, or we leak memory.
Fixes: 7c4e983c4f ("net: allow gso_max_size to exceed 65536")
Reported-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/netdev/c70000f6-baa4-4a05-46d0-4b3e0dc1ccc8@gmail.com/T/
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Xin Long <lucien.xin@gmail.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Coco Li <lixiaoyan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f75cd166a ]
ncsi_channel_is_tx() determines whether a given channel should be
used for Tx or not. However, when reconfiguring the channel by
handling a Configuration Required AEN, there is a misjudgment that
the channel Tx has already been enabled, which results in the Enable
Channel Network Tx command not being sent.
Clear the channel Tx enable flag before reconfiguring the channel to
avoid the misjudgment.
Fixes: 8d951a75d0 ("net/ncsi: Configure multi-package, multi-channel modes with failover")
Signed-off-by: Cosmo Chou <chou.cosmo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c99bace4a ]
After creating SecYs, SCs and SAs a SecY can be modified
to change attributes like validation mode, protect frames
mode etc. During this SecY update, packet number is reset to
initial user given value by mistake. Hence do not reset
PN when updating SecY parameters.
Fixes: c54ffc7360 ("octeontx2-pf: mcs: Introduce MACSEC hardware offloading")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9bdfe61054 ]
Macsec stats like InPktsLate and InPktsDelayed share
same counter in hardware. If SecY replay_protect is true
then counter represents InPktsLate otherwise InPktsDelayed.
This mode change was tracked based on protect_frames
instead of replay_protect mistakenly. Similarly InPktsUnchecked
and InPktsOk share same counter and mode change was tracked
based on validate_check instead of validate_disabled.
This patch fixes those problems.
Fixes: c54ffc7360 ("octeontx2-pf: mcs: Introduce MACSEC hardware offloading")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57d00d4364 ]
On CN10KB silicon a single hardware macsec block is
present and offloads macsec operations for all the
ethernet LMACs. TCAM match with macsec ethertype 0x88e5
alone at RX side is not sufficient to distinguish all the
macsec interfaces created on top of netdevs. Hence append
the DMAC of the macsec interface too. Otherwise the first
created macsec interface only receives all the macsec traffic.
Fixes: c54ffc7360 ("octeontx2-pf: mcs: Introduce MACSEC hardware offloading")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65cdc2b637 ]
When ptp timestamp is enabled in RPM, RPM will append 8B
timestamp header for all RX traffic. MCS need to skip these
8 bytes header while parsing the packet header, so that
correct tcam key is created for lookup.
This patch fixes the mcs parser configuration to skip this
8B header for ptp packets.
Fixes: ca7f49ff88 ("octeontx2-af: cn10k: Introduce driver for macsec block.")
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b516121986 ]
As per hardware errata on CN10KB, all the four TCAM_DATA
and TCAM_MASK registers has to be written at once otherwise
write to individual registers will fail. Hence write to all
TCAM_DATA registers and then to all TCAM_MASK registers.
Fixes: cfc14181d4 ("octeontx2-af: cn10k: mcs: Manage the MCS block hardware resources")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c222b292a3 ]
For each lmac port, MCS has two MCS_TOP_SLAVE_CHANNEL_CONFIGX
registers. For CN10KB both register need to be configured for the
port level mcs bypass to work. This patch also sets bitmap
of flowid/secy entry reserved for default bypass so that these
entries can be shown in debugfs.
Fixes: bd69476e86 ("octeontx2-af: cn10k: mcs: Install a default TCAM for normal traffic")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c23ae5091a ]
Commit 4fe815850b ("ixgbe: let the xdpdrv work with more than 64 cpus")
adds support to allow XDP programs to run on systems with more than
64 CPUs by locking the XDP TX rings and indexing them using cpu % 64
(IXGBE_MAX_XDP_QS).
Upon trying this out patch on a system with more than 64 cores,
the kernel paniced with an array-index-out-of-bounds at the return in
ixgbe_determine_xdp_ring in ixgbe.h, which means ixgbe_determine_xdp_q_idx
was just returning the cpu instead of cpu % IXGBE_MAX_XDP_QS. An example
splat:
==========================================================================
UBSAN: array-index-out-of-bounds in
/var/lib/dkms/ixgbe/5.18.6+focal-1/build/src/ixgbe.h:1147:26
index 65 is out of range for type 'ixgbe_ring *[64]'
==========================================================================
BUG: kernel NULL pointer dereference, address: 0000000000000058
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] SMP NOPTI
CPU: 65 PID: 408 Comm: ksoftirqd/65
Tainted: G IOE 5.15.0-48-generic #54~20.04.1-Ubuntu
Hardware name: Dell Inc. PowerEdge R640/0W23H8, BIOS 2.5.4 01/13/2020
RIP: 0010:ixgbe_xmit_xdp_ring+0x1b/0x1c0 [ixgbe]
Code: 3b 52 d4 cf e9 42 f2 ff ff 66 0f 1f 44 00 00 0f 1f 44 00 00 55 b9
00 00 00 00 48 89 e5 41 57 41 56 41 55 41 54 53 48 83 ec 08 <44> 0f b7
47 58 0f b7 47 5a 0f b7 57 54 44 0f b7 76 08 66 41 39 c0
RSP: 0018:ffffbc3fcd88fcb0 EFLAGS: 00010282
RAX: ffff92a253260980 RBX: ffffbc3fe68b00a0 RCX: 0000000000000000
RDX: ffff928b5f659000 RSI: ffff928b5f659000 RDI: 0000000000000000
RBP: ffffbc3fcd88fce0 R08: ffff92b9dfc20580 R09: 0000000000000001
R10: 3d3d3d3d3d3d3d3d R11: 3d3d3d3d3d3d3d3d R12: 0000000000000000
R13: ffff928b2f0fa8c0 R14: ffff928b9be20050 R15: 000000000000003c
FS: 0000000000000000(0000) GS:ffff92b9dfc00000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000058 CR3: 000000011dd6a002 CR4: 00000000007706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
<TASK>
ixgbe_poll+0x103e/0x1280 [ixgbe]
? sched_clock_cpu+0x12/0xe0
__napi_poll+0x30/0x160
net_rx_action+0x11c/0x270
__do_softirq+0xda/0x2ee
run_ksoftirqd+0x2f/0x50
smpboot_thread_fn+0xb7/0x150
? sort_range+0x30/0x30
kthread+0x127/0x150
? set_kthread_struct+0x50/0x50
ret_from_fork+0x1f/0x30
</TASK>
I think this is how it happens:
Upon loading the first XDP program on a system with more than 64 CPUs,
ixgbe_xdp_locking_key is incremented in ixgbe_xdp_setup. However,
immediately after this, the rings are reconfigured by ixgbe_setup_tc.
ixgbe_setup_tc calls ixgbe_clear_interrupt_scheme which calls
ixgbe_free_q_vectors which calls ixgbe_free_q_vector in a loop.
ixgbe_free_q_vector decrements ixgbe_xdp_locking_key once per call if
it is non-zero. Commenting out the decrement in ixgbe_free_q_vector
stopped my system from panicing.
I suspect to make the original patch work, I would need to load an XDP
program and then replace it in order to get ixgbe_xdp_locking_key back
above 0 since ixgbe_setup_tc is only called when transitioning between
XDP and non-XDP ring configurations, while ixgbe_xdp_locking_key is
incremented every time ixgbe_xdp_setup is called.
Also, ixgbe_setup_tc can be called via ethtool --set-channels, so this
becomes another path to decrement ixgbe_xdp_locking_key to 0 on systems
with more than 64 CPUs.
Since ixgbe_xdp_locking_key only protects the XDP_TX path and is tied
to the number of CPUs present, there is no reason to disable it upon
unloading an XDP program. To avoid confusion, I have moved enabling
ixgbe_xdp_locking_key into ixgbe_sw_init, which is part of the probe path.
Fixes: 4fe815850b ("ixgbe: let the xdpdrv work with more than 64 cpus")
Signed-off-by: John Hickey <jjh@daedalian.us>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230425170308.2522429-1-anthony.l.nguyen@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 32eff6bace ]
Commit 08a0063df3 ("net/sched: flower: Move filter handle initialization
earlier") moved filter handle initialization but an assignment of
the handle to fnew->handle is done regardless of fold value. This is wrong
because if fold != NULL (so fold->handle == handle) no new handle is
allocated and passed handle is assigned to fnew->handle. Then if any
subsequent action in fl_change() fails then the handle value is
removed from IDR that is incorrect as we will have still valid old filter
instance with handle that is not present in IDR.
Fix this issue by moving the assignment so it is done only when passed
fold == NULL.
Prior the patch:
[root@machine tc-testing]# ./tdc.py -d enp1s0f0np0 -e 14be
Test 14be: Concurrently replace same range of 100k flower filters from 10 tc instances
exit: 123
exit: 0
RTNETLINK answers: Invalid argument
We have an error talking to the kernel
Command failed tmp/replace_6:1885
All test results:
1..1
not ok 1 14be - Concurrently replace same range of 100k flower filters from 10 tc instances
Command exited with 123, expected 0
RTNETLINK answers: Invalid argument
We have an error talking to the kernel
Command failed tmp/replace_6:1885
After the patch:
[root@machine tc-testing]# ./tdc.py -d enp1s0f0np0 -e 14be
Test 14be: Concurrently replace same range of 100k flower filters from 10 tc instances
All test results:
1..1
ok 1 14be - Concurrently replace same range of 100k flower filters from 10 tc instances
Fixes: 08a0063df3 ("net/sched: flower: Move filter handle initialization earlier")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230425140604.169881-1-ivecera@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b5fdc0f5c ]
Inside the loop in rxrpc_wait_to_be_connected() it checks call->error to
see if it should exit the loop without first checking the call state. This
is probably safe as if call->error is set, the call is dead anyway, but we
should probably wait for the call state to have been set to completion
first, lest it cause surprise on the way out.
Fix this by only accessing call->error if the call is complete. We don't
actually need to access the error inside the loop as we'll do that after.
This caused the following report:
BUG: KCSAN: data-race in rxrpc_send_data / rxrpc_set_call_completion
write to 0xffff888159cf3c50 of 4 bytes by task 25673 on cpu 1:
rxrpc_set_call_completion+0x71/0x1c0 net/rxrpc/call_state.c:22
rxrpc_send_data_packet+0xba9/0x1650 net/rxrpc/output.c:479
rxrpc_transmit_one+0x1e/0x130 net/rxrpc/output.c:714
rxrpc_decant_prepared_tx net/rxrpc/call_event.c:326 [inline]
rxrpc_transmit_some_data+0x496/0x600 net/rxrpc/call_event.c:350
rxrpc_input_call_event+0x564/0x1220 net/rxrpc/call_event.c:464
rxrpc_io_thread+0x307/0x1d80 net/rxrpc/io_thread.c:461
kthread+0x1ac/0x1e0 kernel/kthread.c:376
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:308
read to 0xffff888159cf3c50 of 4 bytes by task 25672 on cpu 0:
rxrpc_send_data+0x29e/0x1950 net/rxrpc/sendmsg.c:296
rxrpc_do_sendmsg+0xb7a/0xc20 net/rxrpc/sendmsg.c:726
rxrpc_sendmsg+0x413/0x520 net/rxrpc/af_rxrpc.c:565
sock_sendmsg_nosec net/socket.c:724 [inline]
sock_sendmsg net/socket.c:747 [inline]
____sys_sendmsg+0x375/0x4c0 net/socket.c:2501
___sys_sendmsg net/socket.c:2555 [inline]
__sys_sendmmsg+0x263/0x500 net/socket.c:2641
__do_sys_sendmmsg net/socket.c:2670 [inline]
__se_sys_sendmmsg net/socket.c:2667 [inline]
__x64_sys_sendmmsg+0x57/0x60 net/socket.c:2667
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
value changed: 0x00000000 -> 0xffffffea
Fixes: 9d35d880e0 ("rxrpc: Move client call connection to the I/O thread")
Reported-by: syzbot+ebc945fdb4acd72cba78@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/000000000000e7c6d205fa10a3cd@google.com/
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: Dmitry Vyukov <dvyukov@google.com>
cc: "David S. Miller" <davem@davemloft.net>
cc: Eric Dumazet <edumazet@google.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: linux-afs@lists.infradead.org
cc: linux-fsdevel@vger.kernel.org
cc: netdev@vger.kernel.org
Link: https://lore.kernel.org/r/508133.1682427395@warthog.procyon.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 822b84ecfc ]
When the commit fff7eb56b3 ("drm/amd/display: Don't set dram clock
change requirement for SubVP") was merged, we missed some parts
associated with the MCLK switch. This commit adds all the missing parts.
Fixes: fff7eb56b3 ("drm/amd/display: Don't set dram clock change requirement for SubVP")
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5749639f2 ]
In qedi_probe() we call __qedi_probe() which initializes
&qedi->recovery_work with qedi_recovery_handler() and
&qedi->board_disable_work with qedi_board_disable_work().
When qedi_schedule_recovery_handler() is called, schedule_delayed_work()
will finally start the work.
In qedi_remove(), which is called to remove the driver, the following
sequence may be observed:
Fix this by finishing the work before cleanup in qedi_remove().
CPU0 CPU1
|qedi_recovery_handler
qedi_remove |
__qedi_remove |
iscsi_host_free |
scsi_host_put |
//free shost |
|iscsi_host_for_each_session
|//use qedi->shost
Cancel recovery_work and board_disable_work in __qedi_remove().
Fixes: 4b1068f5d7 ("scsi: qedi: Add MFW error recovery process")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Link: https://lore.kernel.org/r/20230413033422.28003-1-zyytlz.wz@163.com
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 948afc6961 ]
When ufshcd_err_handler() is executed, CQ event interrupt can enter waiting
for the same lock. This can happen in ufshcd_handle_mcq_cq_events() and
also in ufs_mtk_mcq_intr(). The following warning message will be generated
when &hwq->cq_lock is used in IRQ context with IRQ enabled. Use
ufshcd_mcq_poll_cqe_lock() with spin_lock_irqsave instead of spin_lock to
resolve the deadlock issue.
[name:lockdep&]WARNING: inconsistent lock state
[name:lockdep&]--------------------------------
[name:lockdep&]inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
[name:lockdep&]kworker/u16:4/260 [HC0[0]:SC0[0]:HE1:SE1] takes:
ffffff8028444600 (&hwq->cq_lock){?.-.}-{2:2}, at:
ufshcd_mcq_poll_cqe_lock+0x30/0xe0
[name:lockdep&]{IN-HARDIRQ-W} state was registered at:
lock_acquire+0x17c/0x33c
_raw_spin_lock+0x5c/0x7c
ufshcd_mcq_poll_cqe_lock+0x30/0xe0
ufs_mtk_mcq_intr+0x60/0x1bc [ufs_mediatek_mod]
__handle_irq_event_percpu+0x140/0x3ec
handle_irq_event+0x50/0xd8
handle_fasteoi_irq+0x148/0x2b0
generic_handle_domain_irq+0x4c/0x6c
gic_handle_irq+0x58/0x134
call_on_irq_stack+0x40/0x74
do_interrupt_handler+0x84/0xe4
el1_interrupt+0x3c/0x78
<snip>
Possible unsafe locking scenario:
CPU0
----
lock(&hwq->cq_lock);
<Interrupt>
lock(&hwq->cq_lock);
*** DEADLOCK ***
2 locks held by kworker/u16:4/260:
[name:lockdep&]
stack backtrace:
CPU: 7 PID: 260 Comm: kworker/u16:4 Tainted: G S W OE
6.1.17-mainline-android14-2-g277223301adb #1
Workqueue: ufs_eh_wq_0 ufshcd_err_handler
Call trace:
dump_backtrace+0x10c/0x160
show_stack+0x20/0x30
dump_stack_lvl+0x98/0xd8
dump_stack+0x20/0x60
print_usage_bug+0x584/0x76c
mark_lock_irq+0x488/0x510
mark_lock+0x1ec/0x25c
__lock_acquire+0x4d8/0xffc
lock_acquire+0x17c/0x33c
_raw_spin_lock+0x5c/0x7c
ufshcd_mcq_poll_cqe_lock+0x30/0xe0
ufshcd_poll+0x68/0x1b0
ufshcd_transfer_req_compl+0x9c/0xc8
ufshcd_err_handler+0x3bc/0xea0
process_one_work+0x2f4/0x7e8
worker_thread+0x234/0x450
kthread+0x110/0x134
ret_from_fork+0x10/0x20
Fixes: ed975065c3 ("scsi: ufs: core: mcq: Add completion support in poll")
Reviewed-by: Can Guo <quic_cang@quicinc.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Alice Chao <alice.chao@mediatek.com>
Link: https://lore.kernel.org/r/20230424080400.8955-1-alice.chao@mediatek.com
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 254e69f284 ]
Syzbot reported a null-ptr-deref bug:
ntfs3: loop0: Different NTFS' sector size (1024) and media sector size
(512)
ntfs3: loop0: Mark volume as dirty due to NTFS errors
general protection fault, probably for non-canonical address
0xdffffc0000000001: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000008-0x000000000000000f]
RIP: 0010:d_flags_for_inode fs/dcache.c:1980 [inline]
RIP: 0010:__d_add+0x5ce/0x800 fs/dcache.c:2796
Call Trace:
<TASK>
d_splice_alias+0x122/0x3b0 fs/dcache.c:3191
lookup_open fs/namei.c:3391 [inline]
open_last_lookups fs/namei.c:3481 [inline]
path_openat+0x10e6/0x2df0 fs/namei.c:3688
do_filp_open+0x264/0x4f0 fs/namei.c:3718
do_sys_openat2+0x124/0x4e0 fs/open.c:1310
do_sys_open fs/open.c:1326 [inline]
__do_sys_open fs/open.c:1334 [inline]
__se_sys_open fs/open.c:1330 [inline]
__x64_sys_open+0x221/0x270 fs/open.c:1330
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
If the MFT record of ntfs inode is not a base record, inode->i_op can be
NULL. And a null-ptr-deref may happen:
ntfs_lookup()
dir_search_u() # inode->i_op is set to NULL
d_splice_alias()
__d_add()
d_flags_for_inode() # inode->i_op->get_link null-ptr-deref
Fix this by adding a Check on inode->i_op before calling the
d_splice_alias() function.
Fixes: 4342306f0f ("fs/ntfs3: Add file operations and implementation")
Reported-by: syzbot+a8f26a403c169b7593fe@syzkaller.appspotmail.com
Signed-off-by: ZhangPeng <zhangpeng362@huawei.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9fd0945fe6 ]
Infineon(Cypress) SEMPER NOR flash family has on-die ECC and its program
granularity is 16-byte ECC data unit size. JFFS2 supports write buffer
mode for ECC'd NOR flash. Provide a way to clear the MTD_BIT_WRITEABLE
flag in order to enable JFFS2 write buffer mode support.
A new SNOR_F_ECC flag is introduced to determine if the part has on-die
ECC and if it has, MTD_BIT_WRITEABLE is unset.
In vendor specific driver, a common cypress_nor_ecc_init() helper is
added. This helper takes care for ECC related initialization for SEMPER
flash family by setting up params->writesize and SNOR_F_ECC.
Fixes: c3266af101 ("mtd: spi-nor: spansion: add support for Cypress Semper flash")
Suggested-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/d586723f6f12aaff44fbcd7b51e674b47ed554ed.1680760742.git.Takahiro.Kuwano@infineon.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4eddee7014 ]
Introduce a new (no SFDP) flag for the feature that we are about to
support: Read While Write. This means, if the chip has several banks and
supports RWW, once a page of data to write has been transferred into the
chip's internal SRAM, another read operation happening on a different
bank can be performed during the tPROG delay.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230328154105.448540-7-miquel.raynal@bootlin.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Stable-dep-of: 9fd0945fe6 ("mtd: spi-nor: spansion: Enable JFFS2 write buffer for Infineon s28hx SEMPER flash")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45121ad4a1 ]
The PSP IRQ is edge-triggered (MSI or MSI-X) in all cases supported by
the psp module so clear the interrupt status register early in the
handler to prevent missed interrupts. sev_irq_handler() calls wake_up()
on a wait queue, which can result in a new command being submitted from
a different CPU. This then races with the clearing of isr and can result
in missed interrupts. A missed interrupt results in a command waiting
until it times out, which results in the psp being declared dead.
This is unlikely on bare metal, but has been observed when running
virtualized. In the cases where this is observed, sev->cmdresp_reg has
PSP_CMDRESP_RESP set which indicates that the command was processed
correctly but no interrupt was asserted.
The full sequence of events looks like this:
CPU 1: submits SEV cmd #1
CPU 1: calls wait_event_timeout()
CPU 0: enters psp_irq_handler()
CPU 0: calls sev_handler()->wake_up()
CPU 1: wakes up; finishes processing cmd #1
CPU 1: submits SEV cmd #2
CPU 1: calls wait_event_timeout()
PSP: finishes processing cmd #2; interrupt status is still set; no interrupt
CPU 0: clears intsts
CPU 0: exits psp_irq_handler()
CPU 1: wait_event_timeout() times out; psp_dead=true
Fixes: 200664d523 ("crypto: ccp: Add Secure Encrypted Virtualization (SEV) command support")
Cc: stable@vger.kernel.org
Signed-off-by: Jeremi Piotrowski <jpiotrowski@linux.microsoft.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c1592a8994 upstream.
Toggle deleted anonymous sets as inactive in the next generation, so
users cannot perform any update on it. Clear the generation bitmask
in case the transaction is aborted.
The following KASAN splat shows a set element deletion for a bound
anonymous set that has been already removed in the same transaction.
[ 64.921510] ==================================================================
[ 64.923123] BUG: KASAN: wild-memory-access in nf_tables_commit+0xa24/0x1490 [nf_tables]
[ 64.924745] Write of size 8 at addr dead000000000122 by task test/890
[ 64.927903] CPU: 3 PID: 890 Comm: test Not tainted 6.3.0+ #253
[ 64.931120] Call Trace:
[ 64.932699] <TASK>
[ 64.934292] dump_stack_lvl+0x33/0x50
[ 64.935908] ? nf_tables_commit+0xa24/0x1490 [nf_tables]
[ 64.937551] kasan_report+0xda/0x120
[ 64.939186] ? nf_tables_commit+0xa24/0x1490 [nf_tables]
[ 64.940814] nf_tables_commit+0xa24/0x1490 [nf_tables]
[ 64.942452] ? __kasan_slab_alloc+0x2d/0x60
[ 64.944070] ? nf_tables_setelem_notify+0x190/0x190 [nf_tables]
[ 64.945710] ? kasan_set_track+0x21/0x30
[ 64.947323] nfnetlink_rcv_batch+0x709/0xd90 [nfnetlink]
[ 64.948898] ? nfnetlink_rcv_msg+0x480/0x480 [nfnetlink]
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0af462f19e upstream.
The recent fix to ensure atomicity of lookup and allocation inadvertently
broke the pool refill mechanism.
Prior to that change debug_objects_activate() and debug_objecs_assert_init()
invoked debug_objecs_init() to set up the tracking object for statically
initialized objects. That's not longer the case and debug_objecs_init() is
now the only place which does pool refills.
Depending on the number of statically initialized objects this can be
enough to actually deplete the pool, which was observed by Ido via a
debugobjects OOM warning.
Restore the old behaviour by adding explicit refill opportunities to
debug_objects_activate() and debug_objecs_assert_init().
Fixes: 63a759694e ("debugobject: Prevent init race with static objects")
Reported-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/871qk05a9d.ffs@tglx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6be2ea33a4 upstream.
Now that a DFS tcon manages its own list of DFS referrals and
sessions, there is no point in having a single worker to refresh
referrals of all DFS tcons. Make it faster and less prone to race
conditions when having several mounts by queueing a worker per DFS
tcon that will take care of refreshing only the DFS referrals related
to it.
Cc: stable@vger.kernel.org # v6.2+
Signed-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3dc9c433c9 upstream.
Protect access of TCP_Server_Info::{origin,leaf}_fullpath when
matching DFS connections, and get rid of
TCP_Server_Info::current_fullpath while we're at it.
Cc: stable@vger.kernel.org # v6.2+
Signed-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee20d7c610 upstream.
Protect access of TCP_Server_Info::hostname when building the ipc tree
name as it might get freed in cifsd thread and thus causing an
use-after-free bug in __tree_connect_dfs_target(). Also, while at it,
update status of IPC tcon on success and then avoid any extra tree
connects.
Cc: stable@vger.kernel.org # v6.2+
Signed-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e3554150d upstream.
When matching DFS connections, we can't rely on the values set in
cifs_sb_info::prepath and cifs_tcon::tree_name as they might change
during DFS failover. The DFS referrals related to a specific DFS tcon
are already matched earlier in match_server(), therefore we can safely
skip those checks altogether as the connection is guaranteed to be
unique for the DFS tcon.
Besides, when creating or finding an SMB session, make sure to also
refcount any DFS root session related to it (cifs_ses::dfs_root_ses),
so if a new DFS mount ends up reusing the connection from the old
mount while there was an umount(2) still in progress (e.g. umount(2)
-> cifs_umount() -> reconnect -> cifs_put_tcon()), the connection
could potentially be put right after the umount(2) finished.
Patch has minor update to include fix for unused variable issue
noted by the kernel test robot
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/oe-kbuild-all/202305041040.j7W2xQSy-lkp@intel.com/
Cc: stable@vger.kernel.org # v6.2+
Signed-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90c49fce1c upstream.
TCP_Server_Info::hostname may be updated once or many times during
reconnect, so protect its access outside reconnect path as well and
then prevent any potential use-after-free bugs.
Cc: stable@vger.kernel.org
Signed-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 776617db78 upstream.
Pages that are from the same folio do not necessarily need to be
consecutive. In that case, we cannot consolidate them into a single bvec
entry. Before applying the huge page optimization from commit 57bebf807e
("io_uring/rsrc: optimise registered huge pages"), check that the memory
is actually consecutive.
Cc: stable@vger.kernel.org
Fixes: 57bebf807e ("io_uring/rsrc: optimise registered huge pages")
Signed-off-by: Tobias Holl <tobias@tholl.xyz>
[axboe: formatting]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 38d11da522 upstream.
Commit fa247089de ("dm: requeue IO if mapping table not yet available")
added a detection of whether the mapping table is available in the IO
submission process. If the mapping table is unavailable, it returns
BLK_STS_RESOURCE and requeues the IO.
This can lead to the following deadlock problem:
dm create mount
ioctl(DM_DEV_CREATE_CMD)
ioctl(DM_TABLE_LOAD_CMD)
do_mount
vfs_get_tree
ext4_get_tree
get_tree_bdev
sget_fc
alloc_super
// got &s->s_umount
down_write_nested(&s->s_umount, ...);
ext4_fill_super
ext4_load_super
ext4_read_bh
submit_bio
// submit and wait io end
ioctl(DM_DEV_SUSPEND_CMD)
dev_suspend
do_resume
dm_suspend
__dm_suspend
lock_fs
freeze_bdev
get_active_super
grab_super
// wait for &s->s_umount
down_write(&s->s_umount);
dm_swap_table
__bind
// set md->map(can't get here)
IO will be continuously requeued while holding the lock since mapping
table is NULL. At the same time, mapping table won't be set since the
lock is not available.
Like request-based DM, bio-based DM also has the same problem.
It's not proper to just abort IO if the mapping table not available.
So clear DM_SKIP_LOCKFS_FLAG when the mapping table is NULL, this
allows the DM table to be loaded and the IO submitted upon resume.
Fixes: fa247089de ("dm: requeue IO if mapping table not yet available")
Cc: stable@vger.kernel.org
Signed-off-by: Li Lingfeng <lilingfeng3@huawei.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d32aaa7e6 upstream.
syzkaller found the following problematic rwsem locking (with write
lock already held):
down_read+0x9d/0x450 kernel/locking/rwsem.c:1509
dm_get_inactive_table+0x2b/0xc0 drivers/md/dm-ioctl.c:773
__dev_status+0x4fd/0x7c0 drivers/md/dm-ioctl.c:844
table_clear+0x197/0x280 drivers/md/dm-ioctl.c:1537
In table_clear, it first acquires a write lock
https://elixir.bootlin.com/linux/v6.2/source/drivers/md/dm-ioctl.c#L1520
down_write(&_hash_lock);
Then before the lock is released at L1539, there is a path shown above:
table_clear -> __dev_status -> dm_get_inactive_table -> down_read
https://elixir.bootlin.com/linux/v6.2/source/drivers/md/dm-ioctl.c#L773
down_read(&_hash_lock);
It tries to acquire the same read lock again, resulting in the deadlock
problem.
Fix this by moving table_clear()'s __dev_status() call to after its
up_write(&_hash_lock);
Cc: stable@vger.kernel.org
Reported-by: Zheng Zhang <zheng.zhang@email.ucr.edu>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e8c5d45f82 upstream.
In verity_end_io(), if bi_status is not BLK_STS_OK, it can be return
directly. But if FEC configured, it is desired to correct the data page
through verity_verify_io. And the return value will be converted to
blk_status and passed to verity_finish_io().
BTW, when a bit is set in v->validated_blocks, verity_verify_io() skips
verification regardless of I/O error for the corresponding bio. In this
case, the I/O error could not be returned properly, and as a result,
there is a problem that abnormal data could be read for the
corresponding block.
To fix this problem, when an I/O error occurs, do not skip verification
even if the bit related is set in v->validated_blocks.
Fixes: 843f38d382 ("dm verity: add 'check_at_most_once' option to only validate hashes once")
Cc: stable@vger.kernel.org
Reviewed-by: Sungjong Seo <sj1557.seo@samsung.com>
Signed-off-by: Yeongjin Gil <youngjin.gil@samsung.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c82729e066 upstream.
While using the vdpa device with vIOMMU enabled
in the guest VM, when the vdpa device bind to vfio-pci and run testpmd
then system will fail to unmap.
The test process is
Load guest VM --> attach to virtio driver--> bind to vfio-pci driver
So the mapping process is
1)batched mode map to normal MR
2)batched mode unmapped the normal MR
3)unmapped all the memory
4)mapped to iommu MR
This error happened in step 3). The iotlb was freed in step 2)
and the function vhost_vdpa_process_iotlb_msg will return fail
Which causes failure.
To fix this, we will not remove the AS while the iotlb->nmaps is 0.
This will free in the vhost_vdpa_clean
Cc: stable@vger.kernel.org
Fixes: aaca8373c4 ("vhost-vdpa: support ASID based IOTLB API")
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20230420151734.860168-1-lulu@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 00ca0f2e86 upstream.
The refactoring in commit f4e9e0e694 ("mm/mempolicy: fix use-after-free
of VMA iterator") introduces a subtle bug which arises when attempting to
apply a new NUMA policy across a range of VMAs in mbind_range().
The refactoring passes a **prev pointer to keep track of the previous VMA
in order to reduce duplication, and in all but one case it keeps this
correctly updated.
The bug arises when a VMA within the specified range has an equivalent
policy as determined by mpol_equal() - which unlike other cases, does not
update prev.
This can result in a situation where, later in the iteration, a VMA is
found whose policy does need to change. At this point, vma_merge() is
invoked with prev pointing to a VMA which is before the previous VMA.
Since vma_merge() discovers the curr VMA by looking for the one
immediately after prev, it will now be in a situation where this VMA is
incorrect and the merge will not proceed correctly.
This is checked in the VM_WARN_ON() invariant case with end >
curr->vm_end, which, if a merge is possible, results in a warning (if
CONFIG_DEBUG_VM is specified).
I note that vma_merge() performs these invariant checks only after
merge_prev/merge_next are checked, which is debatable as it hides this
issue if no merge is possible even though a buggy situation has arisen.
The solution is simply to update the prev pointer even when policies are
equal.
This caused a bug to arise in the 6.2.y stable tree, and this patch
resolves this bug.
Link: https://lkml.kernel.org/r/83f1d612acb519d777bebf7f3359317c4e7f4265.1682866629.git.lstoakes@gmail.com
Fixes: f4e9e0e694 ("mm/mempolicy: fix use-after-free of VMA iterator")
Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com>
Reported-by: kernel test robot <oliver.sang@intel.com>
Link: https://lore.kernel.org/oe-lkp/202304292203.44ddeff6-oliver.sang@intel.com
Cc: Liam R. Howlett <Liam.Howlett@oracle.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 604e6681e1 upstream.
Since the introduction of scrub interface, the only flag that we support
is BTRFS_SCRUB_READONLY. Thus there is no sanity checks, if there are
some undefined flags passed in, we just ignore them.
This is problematic if we want to introduce new scrub flags, as we have
no way to determine if such flags are supported.
Address the problem by introducing a check for the flags, and if
unsupported flags are set, return -EOPNOTSUPP to inform the user space.
This check should be backported for all supported kernels before any new
scrub flags are introduced.
CC: stable@vger.kernel.org # 4.14+
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9ea4eff4b6 ]
afs_read_dir fetches an amount of data that's based on what the inode
size is thought to be. If the file on the server is larger than what
was fetched, the code rechecks i_size and retries. If the local i_size
was not properly updated, this can lead to an endless loop of fetching
i_size from the server and noticing each time that the size is larger on
the server.
If it is known that the remote size is larger than i_size, bump up the
fetch size to that size.
Fixes: f3ddee8dc4 ("afs: Fix directory handling")
Signed-off-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: linux-afs@lists.infradead.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45f66fa03b ]
Fix afs_getattr() to report the server's idea of the file size of a
directory rather than the local size. The local size may differ as we edit
the local copy to avoid having to redownload it and we may end up with a
differently structured blob of a different size.
However, if the directory is discarded from the pagecache we then download
it again and the user may see the directory file size apparently change.
Fixes: 63a4681ff3 ("afs: Locally edit directory data for mkdir/create/unlink/...")
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7f74e9a91 ]
If the data version returned from the server is larger than expected,
the local data is invalidated, but we may still want to note the remote
file size.
Since we're setting change_size, we have to also set data_changed
for the i_size to get updated.
Fixes: 3f4aa98181 ("afs: Fix EOF corruption")
Signed-off-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: linux-afs@lists.infradead.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5904de0d73 ]
The system refused to do a test_resume because it found that the
swap device has already been taken by someone else. Specifically,
the swsusp_check()->blkdev_get_by_dev(FMODE_EXCL) is supposed to
do this check.
Steps to reproduce:
dd if=/dev/zero of=/swapfile bs=$(cat /proc/meminfo |
awk '/MemTotal/ {print $2}') count=1024 conv=notrunc
mkswap /swapfile
swapon /swapfile
swap-offset /swapfile
echo 34816 > /sys/power/resume_offset
echo test_resume > /sys/power/disk
echo disk > /sys/power/state
PM: Using 3 thread(s) for compression
PM: Compressing and saving image data (293150 pages)...
PM: Image saving progress: 0%
PM: Image saving progress: 10%
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/100
ata2: SATA link down (SStatus 0 SControl 300)
ata5: SATA link down (SStatus 0 SControl 300)
ata6: SATA link down (SStatus 0 SControl 300)
ata3: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
PM: Image saving progress: 20%
PM: Image saving progress: 30%
PM: Image saving progress: 40%
PM: Image saving progress: 50%
pcieport 0000:00:02.5: pciehp: Slot(0-5): No device found
PM: Image saving progress: 60%
PM: Image saving progress: 70%
PM: Image saving progress: 80%
PM: Image saving progress: 90%
PM: Image saving done
PM: hibernation: Wrote 1172600 kbytes in 2.70 seconds (434.29 MB/s)
PM: S|
PM: hibernation: Basic memory bitmaps freed
PM: Image not found (code -16)
This is because when using the swapfile as the hibernation storage,
the block device where the swapfile is located has already been mounted
by the OS distribution(usually mounted as the rootfs). This is not
an issue for normal hibernation, because software_resume()->swsusp_check()
happens before the block device(rootfs) mount. But it is a problem for the
test_resume mode. Because when test_resume happens, the block device has
been mounted already.
Thus remove the FMODE_EXCL for test_resume mode. This would not be a
problem because in test_resume stage, the processes have already been
frozen, and the race condition described in
Commit 39fbef4b0f ("PM: hibernate: Get block device exclusively in swsusp_check()")
is unlikely to happen.
Fixes: 39fbef4b0f ("PM: hibernate: Get block device exclusively in swsusp_check()")
Reported-by: Yifan Li <yifan2.li@intel.com>
Suggested-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Tested-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Tested-by: Wendy Wang <wendy.wang@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08169a162f ]
There is need to check snapshot_test and open block device
in different mode, so as to avoid the race condition.
No functional changes intended.
Suggested-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Stable-dep-of: 5904de0d73 ("PM: hibernate: Do not get block device exclusively in test_resume mode")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b04d99788 ]
The CPR3 power resource on the Toshiba Click Mini toggles a GPIO
which is called SISP (for SIS touchscreen power?) on/off.
This CPR3 power resource is not listed in any _PR? lists, let alone
in a _PR0 list for the SIS0817 touchscreen ACPI device which needs it.
Before commit a1224f34d7 ("ACPI: PM: Check states of power resources
during initialization") this was not an issue because since nothing
referenced the CPR3 power resource its state was always
ACPI_POWER_RESOURCE_STATE_UNKNOWN and power resources with this state
get ignored by acpi_turn_off_unused_power_resources().
This clearly is a bug in the DSDT of this device. Add a DMI quirk
to make acpi_turn_off_unused_power_resources() a no-op on this
model to fix the touchscreen no longer working since kernel 5.16 .
This quirk also causes 2 other power resources to not get turned
off, but the _OFF method on these already was a no-op, so this makes
no difference for the other 2 power resources.
Fixes: a1224f34d7 ("ACPI: PM: Check states of power resources during initialization")
Reported-by: Gé Koerkamp <ge.koerkamp@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216946
Link: https://lore.kernel.org/regressions/32a14a8a-9795-4c8c-7e00-da9012f548f8@leemhuis.info/
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e078180d66 ]
The "map_sz" is the number of elements in the "m" array so the >
comparison needs to be changed to >= to prevent an out of bounds
read.
Fixes: 09574cca6a ("hte: Add Tegra194 HTE kernel provider")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Acked-by: Dipen Patel <dipenp@nvidia.com>
Signed-off-by: Dipen Patel <dipenp@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f0484d2f80 ]
Ocelot chips (VSC7511, VSC7512, VSC7513, VSC7514) don't support bulk read
operations over SPI.
Many SPI buses have hardware that can optimize consecutive reads.
Essentially an address is written to the chip, and if the SPI controller
continues to toggle the clock, subsequent register values are reported.
This can lead to significant optimizations, because the time between
"address is written to the chip" and "chip starts to report data" can often
take a fixed amount of time.
When support for Ocelot chips were added in commit f3e893626a ("mfd:
ocelot: Add support for the vsc7512 chip via spi") it was believed that
this optimization was supported. However it is not.
Most register transactions with the Ocelot chips are not done in bulk, so
this bug could go unnoticed. The one scenario where bulk register
operations _are_ performed is when polling port statistics counters, which
was added in commit d87b1c08f3 ("net: mscc: ocelot: use bulk reads for
stats").
Things get slightly more complicated here...
A bug was introduced in commit d4c3676507 ("net: mscc: ocelot: keep
ocelot_stat_layout by reg address, not offset") that broke the optimization
of bulk reads. This means that when Ethernet support for the VSC7512 chip
was added in commit 3d7316ac81 ("net: dsa: ocelot: add external ocelot
switch control") things were actually working "as expected".
The bulk read opmtimization was discovered, and fixed in commit
6acc72a43e ("net: mscc: ocelot: fix stats region batching") and the
timing optimizations for SPI were noticed. A bulk read went from ~14ms to
~2ms. But this timing improvement came at the cost of every register
reading zero due the fact that bulk reads don't work.
The read timings increase back to 13-14ms, but that's a price worth paying
in order to receive valid data. This is verified in a DSA setup (cpsw-new
switch tied to port 0 on the VSC7512, after having been running overnight)
Rx Octets: 16222055 # Counters from CPSW switch
Tx Octets: 12034702
Net Octets: 28256757
p00_rx_octets: 12034702 # Counters from Ocelot switch
p00_rx_frames_below_65_octets: 0
p00_rx_frames_65_to_127_octets: 88188
p00_rx_frames_128_to_255_octets: 13
p00_rx_frames_256_to_511_octets: 0
p00_rx_frames_512_to_1023_octets: 0
p00_rx_frames_over_1526_octets: 3306
p00_tx_octets: 16222055
Fixes: f3e893626a ("mfd: ocelot: Add support for the vsc7512 chip via spi")
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230322141130.2531256-1-colin.foster@in-advantage.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f376c47966 ]
It seems that this driver was developed based on preliminary documentation.
Report the correct names for all TQMxE39x variants, as they are used by
the released hardware revisions:
- Fix names for TQMxE39C1/C2 board IDs
- Distinguish TQMxE39M and TQMxE39S, which use the same board ID
The TQMxE39M/S are distinguished using the SAUC (Sanctioned Alternate
Uses Configuration) register of the GPIO controller. This also prepares
for the correct handling of the differences between the GPIO controllers
of our COMe and SMARC modules.
Fixes: 2f17dd34ff ("mfd: tqmx86: IO controller with I2C, Wachdog and GPIO")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/aca9a7cb42a85181bcb456c437554d2728e708ec.1676892223.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1be1b23696 ]
The I2C_DETECT register is at IO port 0x1a7, which is outside the range
passed to devm_ioport_map() for io_base, and was only working because
there aren't actually any bounds checks for IO port accesses.
Extending the range does not seem like a good solution here, as it would
then conflict with the IO resource assigned to the I2C controller. As
this is just a one-off access during probe, use a simple inb() instead.
While we're at it, drop the unused define TQMX86_REG_I2C_INT_EN.
Fixes: 2f17dd34ff ("mfd: tqmx86: IO controller with I2C, Wachdog and GPIO")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/e8300a30f0791afb67d79db8089fb6004855f378.1676892223.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7badd752d ]
In the past setting the pin direction called pinctrl_gpio_direction()
which uses a mutex to serialize this. That was changed to set the
direction directly in the pin controller driver, but that lost the
serialization mechanism. Since the direction of multiple pins are in
the same register you can have a race condition, something that was
in fact observed with the cec-gpio driver.
Add a new spinlock to serialize writing to the FSEL registers.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 1a4541b68e ("pinctrl-bcm2835: don't call pinctrl_gpio_direction()")
Link: https://lore.kernel.org/r/4302b66b-ca20-0f19-d2aa-ee8661118863@xs4all.nl
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c5eb63d16 ]
In case the system suspends to a deep sleep state where power to DMA
controller is cut-off we need to restore the content of GRWS register.
This is a write only register and writing bit X tells the controller
to suspend read and write requests for channel X. Thus set GRWS before
restoring the content of GE (Global Enable) regiter.
Fixes: e1f7c9eee7 ("dmaengine: at_xdmac: creation of the atmel eXtended DMA Controller driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230214151827.1050280-5-claudiu.beznea@microchip.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44fe8440bd ]
In case there are DMA channels not paused by consumers in suspend
process (valid on AT91 SoCs for serial driver when no_console_suspend) the
driver pauses them (using at_xdmac_device_pause() which is also the same
function called by dmaengine_pause()) and then in the resume process the
driver resumes them calling at_xdmac_device_resume() which is the same
function called by dmaengine_resume()). This is good for DMA channels
not paused by consumers but for drivers that calls
dmaengine_pause()/dmaegine_resume() on suspend/resume path this may lead to
DMA channel being enabled before the IP is enabled. For IPs that needs
strict ordering with regards to DMA channel enablement this will lead to
wrong behavior. To fix this add a new set of functions
at_xdmac_device_pause_internal()/at_xdmac_device_resume_internal() to be
called only on suspend/resume.
Fixes: e1f7c9eee7 ("dmaengine: at_xdmac: creation of the atmel eXtended DMA Controller driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230214151827.1050280-4-claudiu.beznea@microchip.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e53957e1ec ]
In case there are channels not paused during suspend (which on AT91 case
is valid for serial driver when no_console_suspend boot argument is used)
the at_xdmac_runtime_suspend_descriptors() was called more than
one time due to at_xdmac_off(). To fix this add a new argument to
at_xdmac_off() to specify if runtime PM reference counter needs to be
decremented for queued active descriptors. Along with it moved the
at_xdmac_runtime_suspend_descriptors() call under at_xdmac_chan_is_paused()
check on suspend path as for the rest of channels the suspend is delayed
by atmel_xdmac_prepare() in case channel is enabled. Same approach has
been applied on resume path.
Fixes: 650b0e990c ("dmaengine: at_xdmac: add runtime pm support")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230214151827.1050280-3-claudiu.beznea@microchip.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2de5ddb5e6 ]
Runtime PM APIs for at_xdmac just plays with clk_enable()/clk_disable()
letting aside the clk_prepare()/clk_unprepare() that needs to be
executed as the clock is also prepared on probe. Thus instead of using
runtime PM force suspend/resume APIs use
clk_disable_unprepare() + pm_runtime_put_noidle() on suspend and
clk_prepare_enable() + pm_runtime_get_noresume() on resume. This
approach as been chosen instead of using runtime PM force suspend/resume
with clk_unprepare()/clk_prepare() as it looks simpler and the final
code is better.
While at it added the missing pm_runtime_mark_last_busy() on suspend before
decrementing the reference counter.
Fixes: 650b0e990c ("dmaengine: at_xdmac: add runtime pm support")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230214151827.1050280-2-claudiu.beznea@microchip.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a251994a44 ]
The dw-edma driver stops after processing a DMA request even if a request
remains in the issued queue, which is not the expected behavior. The DMA
engine API requires continuous processing.
Add a trigger to start after one processing finished if there are requests
remain.
Fixes: e63d79d1ff ("dmaengine: Add Synopsys eDMA IP core driver")
Signed-off-by: Shunsuke Mie <mie@igel.co.jp>
Link: https://lore.kernel.org/r/20230411101758.438472-1-mie@igel.co.jp
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a0d1740bd ]
The existing code copies the hw_params pointer and reuses it later in
.prepare, specifically to re-initialize the ALH DMA channel
information that's lost in suspend-resume cycles.
This is not needed, we can directly access the information from the
substream/rtd - as done for the HDAudio DAIs in
sound/soc/sof/intel/hda-dai.c
In addition, using the saved pointer causes the suspend-resume test
cases to fail on specific platforms, depending on which version of GCC
is used. Péter Ujfalusi and I have spent long hours to root-cause this
problem that was reported by the Intel CI first with 6.2-rc1 and again
v6.3-rc1. In the latter case we were lucky that the problem was 100%
reproducible on local test devices, and found out that adding a
dev_dbg() or adding a call to usleep_range() just before accessing the
saved pointer "fixed" the issue. With errors appearing just by
changing the compiler version or minor changes in the code generated,
clearly we have a memory management Heisenbug.
The root-cause seems to be that the hw_params pointer is not
persistent. The soc-pcm code allocates the hw_params structure on the
stack, and passes it to the BE dailink hw_params and DAIs
hw_params. Saving such a pointer and reusing it later during the
.prepare stage cannot possibly work reliably, it's broken-by-design
since v5.10. It's astonishing that the problem was not seen earlier.
This simple fix will have to be back-ported to -stable, due to changes
to avoid the use of the get/set_dmadata routines this patch will only
apply on kernels older than v6.1.
Fixes: a5a0239c27 ("soundwire: intel: reinitialize IP+DSP in .prepare(), but only when resuming")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20230321022642.1426611-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b16c310115 ]
The DISP_PWM controller's default behavior is to always use register
double buffering: all reads/writes are then performed on shadow
registers instead of working registers and this becomes an issue
in case our chosen configuration in Linux is different from the
default (or from the one that was pre-applied by the bootloader).
An example of broken behavior is when the controller is configured
to use shadow registers, but this driver wants to configure it
otherwise: what happens is that the .get_state() callback is called
right after registering the pwmchip and checks whether the PWM is
enabled by reading the DISP_PWM_EN register;
At this point, if shadow registers are enabled but their content
was not committed before booting Linux, we are *not* reading the
current PWM enablement status, leading to the kernel knowing that
the hardware is actually enabled when, in reality, it's not.
The aforementioned issue emerged since this driver was fixed with
commit 0b5ef3429d ("pwm: mtk-disp: Fix the parameters calculated
by the enabled flag of disp_pwm") making it to read the enablement
status from the right register.
Configure the controller in the .get_state() callback to avoid
this desync issue and get the backlight properly working again.
Fixes: 3f2b167349 ("pwm: mtk-disp: Implement atomic API .get_state()")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Tested-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1087c29e9 ]
Commit 96f524105b ("leds: tca6507: use fwnode API instead of OF")
changed to fwnode API but did not take into account that a missing property
"linux,default-trigger" now seems to return an error and as a side effect
sets value to -1. This seems to be different from of_get_property() which
always returned NULL in any case of error.
Neglecting this side-effect leads to
[ 11.201965] Unable to handle kernel paging request at virtual address ffffffff when read
in the strcmp() of led_trigger_set_default() if there is no led-trigger
defined in the DTS.
I don't know if this was recently introduced somewhere in the fwnode lib
or if the effect was missed in initial testing. Anyways it seems to be a
bug to ignore the error return value of an optional value here in the
driver.
Fixes: 96f524105b ("leds: tca6507: use fwnode API instead of OF")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/cbae7617db83113de726fcc423a805ebaa1bfca6.1680433978.git.hns@goldelico.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a61079efc8 ]
REGMAP is a hidden (not user visible) symbol. Users cannot set it
directly thru "make *config", so drivers should select it instead of
depending on it if they need it.
Consistently using "select" or "depends on" can also help reduce
Kconfig circular dependency issues.
Therefore, change the use of "depends on REGMAP" to "select REGMAP".
Fixes: 3fce8e1eb9 ("leds: TI LMU: Add common code for TI LMU devices")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230226053953.4681-5-rdunlap@infradead.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 835659598c ]
Syzbot found the following issue:
loop0: detected capacity change from 0 to 2048
EXT4-fs (loop0): mounted filesystem 00000000-0000-0000-0000-000000000000 without journal. Quota mode: none.
==================================================================
BUG: KASAN: use-after-free in ext4_ext_binsearch_idx fs/ext4/extents.c:768 [inline]
BUG: KASAN: use-after-free in ext4_find_extent+0x76e/0xd90 fs/ext4/extents.c:931
Read of size 4 at addr ffff888073644750 by task syz-executor420/5067
CPU: 0 PID: 5067 Comm: syz-executor420 Not tainted 6.2.0-rc1-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/26/2022
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x1b1/0x290 lib/dump_stack.c:106
print_address_description+0x74/0x340 mm/kasan/report.c:306
print_report+0x107/0x1f0 mm/kasan/report.c:417
kasan_report+0xcd/0x100 mm/kasan/report.c:517
ext4_ext_binsearch_idx fs/ext4/extents.c:768 [inline]
ext4_find_extent+0x76e/0xd90 fs/ext4/extents.c:931
ext4_clu_mapped+0x117/0x970 fs/ext4/extents.c:5809
ext4_insert_delayed_block fs/ext4/inode.c:1696 [inline]
ext4_da_map_blocks fs/ext4/inode.c:1806 [inline]
ext4_da_get_block_prep+0x9e8/0x13c0 fs/ext4/inode.c:1870
ext4_block_write_begin+0x6a8/0x2290 fs/ext4/inode.c:1098
ext4_da_write_begin+0x539/0x760 fs/ext4/inode.c:3082
generic_perform_write+0x2e4/0x5e0 mm/filemap.c:3772
ext4_buffered_write_iter+0x122/0x3a0 fs/ext4/file.c:285
ext4_file_write_iter+0x1d0/0x18f0
call_write_iter include/linux/fs.h:2186 [inline]
new_sync_write fs/read_write.c:491 [inline]
vfs_write+0x7dc/0xc50 fs/read_write.c:584
ksys_write+0x177/0x2a0 fs/read_write.c:637
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
RIP: 0033:0x7f4b7a9737b9
RSP: 002b:00007ffc5cac3668 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f4b7a9737b9
RDX: 00000000175d9003 RSI: 0000000020000200 RDI: 0000000000000004
RBP: 00007f4b7a933050 R08: 0000000000000000 R09: 0000000000000000
R10: 000000000000079f R11: 0000000000000246 R12: 00007f4b7a9330e0
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
</TASK>
Above issue is happens when enable bigalloc and inline data feature. As
commit 131294c35e fixed delayed allocation bug in ext4_clu_mapped for
bigalloc + inline. But it only resolved issue when has inline data, if
inline data has been converted to extent(ext4_da_convert_inline_data_to_extent)
before writepages, there is no EXT4_STATE_MAY_INLINE_DATA flag. However
i_data is still store inline data in this scene. Then will trigger UAF
when find extent.
To resolve above issue, there is need to add judge "ext4_has_inline_data(inode)"
in ext4_clu_mapped().
Fixes: 131294c35e ("ext4: fix delayed allocation bug in ext4_clu_mapped for bigalloc + inline")
Reported-by: syzbot+bf4bb7731ef73b83a3b4@syzkaller.appspotmail.com
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Ye Bin <yebin10@huawei.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Tested-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20230406111627.1916759-1-tudor.ambarus@linaro.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1dedde6903 ]
It is possible for i_disksize can exceed i_size, triggering a warning.
generic_perform_write
copied = iov_iter_copy_from_user_atomic(len) // copied < len
ext4_da_write_end
| ext4_update_i_disksize
| new_i_size = pos + copied;
| WRITE_ONCE(EXT4_I(inode)->i_disksize, newsize) // update i_disksize
| generic_write_end
| copied = block_write_end(copied, len) // copied = 0
| if (unlikely(copied < len))
| if (!PageUptodate(page))
| copied = 0;
| if (pos + copied > inode->i_size) // return false
if (unlikely(copied == 0))
goto again;
if (unlikely(iov_iter_fault_in_readable(i, bytes))) {
status = -EFAULT;
break;
}
We get i_disksize greater than i_size here, which could trigger WARNING
check 'i_size_read(inode) < EXT4_I(inode)->i_disksize' while doing dio:
ext4_dio_write_iter
iomap_dio_rw
__iomap_dio_rw // return err, length is not aligned to 512
ext4_handle_inode_extension
WARN_ON_ONCE(i_size_read(inode) < EXT4_I(inode)->i_disksize) // Oops
WARNING: CPU: 2 PID: 2609 at fs/ext4/file.c:319
CPU: 2 PID: 2609 Comm: aa Not tainted 6.3.0-rc2
RIP: 0010:ext4_file_write_iter+0xbc7
Call Trace:
vfs_write+0x3b1
ksys_write+0x77
do_syscall_64+0x39
Fix it by updating 'copied' value before updating i_disksize just like
ext4_write_inline_data_end() does.
A reproducer can be found in the buganizer link below.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217209
Fixes: 64769240bd ("ext4: Add delayed allocation support in data=writeback mode")
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20230321013721.89818-1-chengzhihao1@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7a639dac8 ]
The jz4740 RTC driver registers a clock provider, but never removes it.
This leaves a stale clock provider behind that references freed clocks when
the device is unbound.
Use the managed `devm_of_clk_add_hw_provider()` instead of
`of_clk_add_hw_provider()` to make sure the provider gets automatically
removed on unbind.
Fixes: 5ddfa148de ("rtc: jz4740: Register clock provider for the CLK32K pin")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20230409162544.16155-1-lars@metafoo.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d906be3fa5 ]
We should not cache deferred file handles if we dont have
handle lease on a file. And we should immediately close all
deferred handles in case of handle lease break.
Fixes: 9e31678fb4 ("SMB3: fix lease break timeout when multiple deferred close handles for the same file.")
Signed-off-by: Bharath SM <bharathsm@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab9ddc87a9 ]
cifs_del_deferred_close function has a critical section which modifies
the deferred close file list. We must acquire deferred_lock before
calling cifs_del_deferred_close function.
Fixes: ca08d0eac0 ("cifs: Fix memory leak on the deferred close")
Signed-off-by: Bharath SM <bharathsm@microsoft.com>
Acked-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Acked-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 812489ac4d ]
In commit 91993c8c2e ("openrisc: use shadow registers to save regs on
exception") the unhandled exception path was changed to do an early
store of r30 instead of r31. The entry code was not updated and r31 is
not getting stored to pt_regs.
This patch updates the entry handler to store r31 instead of r30. We
also remove some misleading commented out store r30 and r31
instructrions.
I noticed this while working on adding floating point exception
handling, This issue probably would never impact anything since we kill
the process or Oops right away on unhandled exceptions.
Fixes: 91993c8c2e ("openrisc: use shadow registers to save regs on exception")
Signed-off-by: Stafford Horne <shorne@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 691d0b7820 ]
Currently call_bind_status places a hard limit of 3 to the number of
retries on EACCES error. This limit was done to prevent NLM unlock
requests from being hang forever when the server keeps returning garbage.
However this change causes problem for cases when NLM service takes
longer than 9 seconds to register with the port mapper after a restart.
This patch removes this hard coded limit and let the RPC handles
the retry based on the standard hard/soft task semantics.
Fixes: 0b760113a3 ("NLM: Don't hang forever on NLM unlock requests")
Reported-by: Helen Chao <helen.chao@oracle.com>
Tested-by: Helen Chao <helen.chao@oracle.com>
Signed-off-by: Dai Ngo <dai.ngo@oracle.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d43b020b0f ]
relaxed_ordering_read HCA capability is set if both the device supports
relaxed ordering (RO) read and RO is set in PCI config space.
RO in PCI config space can change during runtime. This will change the
value of relaxed_ordering_read HCA capability in FW, but the driver will
not see it since it queries the capabilities only once.
This can lead to the following scenario:
1. RO in PCI config space is enabled.
2. User creates MKey without RO.
3. RO in PCI config space is disabled.
As a result, relaxed_ordering_read HCA capability is turned off in FW
but remains on in driver copy of the capabilities.
4. User requests to reconfig the MKey with RO via UMR.
5. Driver will try to reconfig the MKey with RO read although it
shouldn't (as relaxed_ordering_read HCA capability is really off).
To fix this, check pcie_relaxed_ordering_enabled() before setting RO
read in UMR.
Fixes: 896ec97353 ("RDMA/mlx5: Set mkey relaxed ordering by UMR with ConnectX-7")
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Link: https://lore.kernel.org/r/8d39eb8317e7bed1a354311a20ae707788fd94ed.1681131553.git.leon@kernel.org
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 960ebe97e5 ]
The subroutine __rxe_do_task is not thread safe and it has no way to
guarantee that the tasks, which are designed with the assumption that they
are non-reentrant, are not reentered. All of its uses are non-performance
critical.
This patch replaces calls to __rxe_do_task with calls to
rxe_sched_task. It also removes irrelevant or unneeded if tests.
Instead of calling the task machinery a single call to the tasklet
function (rxe_requester, etc.) is sufficient to draing the queues if task
execution has been disabled or stopped.
Together these changes allow the removal of __rxe_do_task.
Link: https://lore.kernel.org/r/20230304174533.11296-7-rpearsonhpe@gmail.com
Signed-off-by: Ian Ziemba <ian.ziemba@hpe.com>
Signed-off-by: Bob Pearson <rpearsonhpe@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Stable-dep-of: b2b1ddc457 ("RDMA/rxe: Fix the error "trying to register non-static key in rxe_cleanup_task"")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3946fc2a42 ]
Originally is was thought that the tasklet machinery in rxe_task.c would
be used in other applications but that has not happened for years. This
patch replaces the 'void *arg' by struct 'rxe_qp *qp' in the parameters to
the tasklet calls. This change will have no affect on performance but may
make the code a little clearer.
Link: https://lore.kernel.org/r/20230304174533.11296-2-rpearsonhpe@gmail.com
Signed-off-by: Bob Pearson <rpearsonhpe@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Stable-dep-of: b2b1ddc457 ("RDMA/rxe: Fix the error "trying to register non-static key in rxe_cleanup_task"")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5499d01c02 ]
For io_tlb_nslabs, the debugfs code reports the correct value for a
specific reserved memory pool. But for io_tlb_used, the value reported
is always for the default pool, not the specific reserved pool. Fix this.
Fixes: 5c850d3188 ("swiotlb: fix passing local variable to debugfs_create_ulong()")
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a90922fa25 ]
The reservedmem_of_init_fn's are invoked very early at boot before the
memory zones have even been defined. This makes it inappropriate to test
whether the page corresponding to a PFN is in ZONE_HIGHMEM from within
one.
Removing the check allows an ARM 32-bit kernel with SPARSEMEM enabled to
boot properly since otherwise we would be de-referencing an
uninitialized sparsemem map to perform pfn_to_page() check.
The arm64 architecture happens to work (and also has no high memory) but
other 32-bit architectures could also be having similar issues.
While it would be nice to provide early feedback about a reserved DMA
pool residing in highmem, it is not possible to do that until the first
time we try to use it, which is where the check is moved to.
Fixes: 0b84e4f8b7 ("swiotlb: Add restricted DMA pool initialization")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a500e0bc9 ]
On SM8350 platform the PCIe PIPE clocks require additional handling to
function correctly. They are to be switched to the tcxo source before
turning PCIe GDSCs off and should be switched to PHY PIPE source once
they are working. Switch PCIe PHY clocks to use clk_regmap_phy_mux_ops,
which provide support for this dance.
Fixes: 44c20c9ed3 ("clk: qcom: gcc: Add clock driver for SM8350")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230412134829.3686467-1-dmitry.baryshkov@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e42ac7789d ]
Commit dfe843dce7 ("s390/checksum: support GENERIC_CSUM, enable it for
KASAN") switched s390 to use the generic checksum functions, so that KASAN
instrumentation also works checksum functions by avoiding architecture
specific inline assemblies.
There is however the problem that the generic csum_partial() function
returns a 32 bit value with a 16 bit folded checksum, while the original
s390 variant does not fold to 16 bit. This in turn causes that the
ipib_checksum in lowcore contains different values depending on kernel
config options.
The ipib_checksum is used by system dumpers to verify if pointers in
lowcore point to valid data. Verification is done by comparing checksum
values. The system dumpers still use 32 bit checksum values which are not
folded, and therefore the checksum verification fails (incorrectly).
Symptom is that reboot after dump does not work anymore when a KASAN
instrumented kernel is dumped.
Fix this by not using the generic checksum implementation. Instead add an
explicit kasan_check_read() so that KASAN knows about the read access from
within the inline assembly.
Reported-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Fixes: dfe843dce7 ("s390/checksum: support GENERIC_CSUM, enable it for KASAN")
Tested-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f880d19e6 ]
With the addition of the V2 page table support, the domain page size
bitmap needs to be set prior to iommu core setting up direct mappings
for reserved regions. When reserved regions are mapped, if this is not
done, it will be looking at the V1 page size bitmap when determining
the page size to use in iommu_pgsize(). When it gets into the actual
amd mapping code, a check of see if the page size is supported can
fail, because at that point it is checking it against the V2 page size
bitmap which only supports 4K, 2M, and 1G.
Add a check to __iommu_domain_alloc() to not override the
bitmap if it was already set by the iommu ops domain_alloc() code path.
Cc: Vasant Hegde <vasant.hegde@amd.com>
Cc: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Joerg Roedel <joro@8bytes.org>
Fixes: 4db6c41f09 ("iommu/amd: Add support for using AMD IOMMU v2 page table for DMA-API")
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Link: https://lore.kernel.org/r/20230404072742.1895252-1-jsnitsel@redhat.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 40882deb83 ]
The spec requires that we always at least send a RECLAIM_COMPLETE when
we're done establishing the lease and recovering any state.
Fixes: fce5c838e1 ("nfs41: RECLAIM_COMPLETE functionality")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 00cbce5cbf ]
hfi1 user SDMA request processing has two bugs that can cause data
corruption for user SDMA requests that have multiple payload iovecs
where an iovec other than the tail iovec does not run up to the page
boundary for the buffer pointed to by that iovec.a
Here are the specific bugs:
1. user_sdma_txadd() does not use struct user_sdma_iovec->iov.iov_len.
Rather, user_sdma_txadd() will add up to PAGE_SIZE bytes from iovec
to the packet, even if some of those bytes are past
iovec->iov.iov_len and are thus not intended to be in the packet.
2. user_sdma_txadd() and user_sdma_send_pkts() fail to advance to the
next iovec in user_sdma_request->iovs when the current iovec
is not PAGE_SIZE and does not contain enough data to complete the
packet. The transmitted packet will contain the wrong data from the
iovec pages.
This has not been an issue with SDMA packets from hfi1 Verbs or PSM2
because they only produce iovecs that end short of PAGE_SIZE as the tail
iovec of an SDMA request.
Fixing these bugs exposes other bugs with the SDMA pin cache
(struct mmu_rb_handler) that get in way of supporting user SDMA requests
with multiple payload iovecs whose buffers do not end at PAGE_SIZE. So
this commit fixes those issues as well.
Here are the mmu_rb_handler bugs that non-PAGE_SIZE-end multi-iovec
payload user SDMA requests can hit:
1. Overlapping memory ranges in mmu_rb_handler will result in duplicate
pinnings.
2. When extending an existing mmu_rb_handler entry (struct mmu_rb_node),
the mmu_rb code (1) removes the existing entry under a lock, (2)
releases that lock, pins the new pages, (3) then reacquires the lock
to insert the extended mmu_rb_node.
If someone else comes in and inserts an overlapping entry between (2)
and (3), insert in (3) will fail.
The failure path code in this case unpins _all_ pages in either the
original mmu_rb_node or the new mmu_rb_node that was inserted between
(2) and (3).
3. In hfi1_mmu_rb_remove_unless_exact(), mmu_rb_node->refcount is
incremented outside of mmu_rb_handler->lock. As a result, mmu_rb_node
could be evicted by another thread that gets mmu_rb_handler->lock and
checks mmu_rb_node->refcount before mmu_rb_node->refcount is
incremented.
4. Related to #2 above, SDMA request submission failure path does not
check mmu_rb_node->refcount before freeing mmu_rb_node object.
If there are other SDMA requests in progress whose iovecs have
pointers to the now-freed mmu_rb_node(s), those pointers to the
now-freed mmu_rb nodes will be dereferenced when those SDMA requests
complete.
Fixes: 7be85676f1 ("IB/hfi1: Don't remove RB entry when not needed.")
Fixes: 7724105686 ("IB/hfi1: add driver files")
Signed-off-by: Brendan Cunningham <bcunningham@cornelisnetworks.com>
Signed-off-by: Patrick Kelsey <pat.kelsey@cornelisnetworks.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Link: https://lore.kernel.org/r/168088636445.3027109.10054635277810177889.stgit@252.162.96.66.static.eigbox.net
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9fe8fec5e4 ]
hfi1_mmu_rb_remove_unless_exact() did not move mmu_rb_node objects in
mmu_rb_handler->lru_list after getting a cache hit on an mmu_rb_node.
As a result, hfi1_mmu_rb_evict() was not guaranteed to evict truly
least-recently used nodes.
This could be a performance issue for an application when that
application:
- Uses some long-lived buffers frequently.
- Uses a large number of buffers once.
- Hits the mmu_rb_handler cache size or pinned-page limits, forcing
mmu_rb_handler cache entries to be evicted.
In this case, the one-time use buffers cause the long-lived buffer
entries to eventually filter to the end of the LRU list where
hfi1_mmu_rb_evict() will consider evicting a frequently-used long-lived
entry instead of evicting one of the one-time use entries.
Fix this by inserting new mmu_rb_node at the tail of
mmu_rb_handler->lru_list and move mmu_rb_ndoe to the tail of
mmu_rb_handler->lru_list when the mmu_rb_node is a hit in
hfi1_mmu_rb_remove_unless_exact(). Change hfi1_mmu_rb_evict() to evict
from the head of mmu_rb_handler->lru_list instead of the tail.
Fixes: 0636e9ab83 ("IB/hfi1: Add cache evict LRU list")
Signed-off-by: Brendan Cunningham <bcunningham@cornelisnetworks.com>
Signed-off-by: Patrick Kelsey <pat.kelsey@cornelisnetworks.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Link: https://lore.kernel.org/r/168088635931.3027109.10423156330761536044.stgit@252.162.96.66.static.eigbox.net
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd9de1bada ]
Trace icm_send_rej event before the cm state is reset to idle, so that
correct cm state will be logged. For example when an incoming request is
rejected, the old trace log was:
icm_send_rej: local_id=961102742 remote_id=3829151631 state=IDLE reason=REJ_CONSUMER_DEFINED
With this patch:
icm_send_rej: local_id=312971016 remote_id=3778819983 state=MRA_REQ_SENT reason=REJ_CONSUMER_DEFINED
Fixes: 8dc105befe ("RDMA/cm: Add tracepoints to track MAD send operations")
Signed-off-by: Mark Zhang <markzhang@nvidia.com>
Link: https://lore.kernel.org/r/20230330072351.481200-1-markzhang@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit baba1315a7 ]
When the SOC approaches zero, an integer overflows in the columb
counter causing the driver to react poorly. This makes the driver
think it's at (above) the fully charged capacity when in fact it's
zero. It would then write this full capacity to NVRAM which would be
used on boot if the device remained off for less than 5 hours and
not plugged in.
This can be fixed and guarded against by doing the following:
- Changing the type of tmp in rk817_read_or_set_full_charge_on_boot()
to be an int instead of a u32. That way we can account for negative
numbers.
- Guard against negative values for the full charge on boot by setting
the charge to 0 if the system charge reports less than 0.
- Catch scenarios where the battery voltage is below the design
minimum voltage and set the system SOC to 0 at that time and update
the columb counter with a charge level of 0.
- Change the off time value from 5 hours to 30 minutes before we
recalculate the current capacity based on the OCV tables.
These changes allow the driver to operate better at low voltage/low
capacity conditions.
Fixes: 3268a4d9b0 ("power: supply: rk817: Fix unsigned comparison with less than zero")
Fixes: 11cb8da018 ("power: supply: Add charger driver for Rockchip RK817")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44263f5006 ]
power-supply properties are reported in µV, µA and µW.
The IIO API provides mV, mA, mW, so the values need to
be multiplied by 1000.
Fixes: e60fea794e ("power: battery: Generic battery driver using IIO")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78b26a3353 ]
Remove the tasklet call in rxe_cq.c and also the is_dying in the
cq struct. There is no reason for the rxe driver to defer the call
to the cq completion handler by scheduling a tasklet. rxe_cq_post()
is not called in a hard irq context.
The rxe driver currently is incorrect because the tasklet call is
made without protecting the cq pointer with a reference from having
the underlying memory freed before the deferred routine is called.
Executing the comp_handler inline fixes this problem.
Fixes: 8700e3e7c4 ("Soft RoCE driver")
Signed-off-by: Bob Pearson <rpearsonhpe@gmail.com>
Link: https://lore.kernel.org/r/20230327215643.10410-1-rpearsonhpe@gmail.com
Acked-by: Zhu Yanjun <zyjzyj2000@gmail.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab84eee4c7 ]
Here is a BUG report from syzbot:
BUG: KASAN: slab-out-of-bounds in hdr_delete_de+0xe0/0x150 fs/ntfs3/index.c:806
Read of size 16842960 at addr ffff888079cc0600 by task syz-executor934/3631
Call Trace:
memmove+0x25/0x60 mm/kasan/shadow.c:54
hdr_delete_de+0xe0/0x150 fs/ntfs3/index.c:806
indx_delete_entry+0x74f/0x3670 fs/ntfs3/index.c:2193
ni_remove_name+0x27a/0x980 fs/ntfs3/frecord.c:2910
ntfs_unlink_inode+0x3d4/0x720 fs/ntfs3/inode.c:1712
ntfs_rename+0x41a/0xcb0 fs/ntfs3/namei.c:276
Before using the meta-data in struct INDEX_HDR, we need to
check index header valid or not. Otherwise, the corruptedi
(or malicious) fs image can cause out-of-bounds access which
could make kernel panic.
Fixes: 82cae269cf ("fs/ntfs3: Add initialization of super block")
Reported-by: syzbot+9c2811fd56591639ff5f@syzkaller.appspotmail.com
Signed-off-by: Zeng Heng <zengheng4@huawei.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8c4494904 ]
Syzbot reported a OOB read bug:
BUG: KASAN: slab-out-of-bounds in indx_insert_into_buffer+0xaa3/0x13b0
fs/ntfs3/index.c:1755
Read of size 17168 at addr ffff8880255e06c0 by task syz-executor308/3630
Call Trace:
<TASK>
memmove+0x25/0x60 mm/kasan/shadow.c:54
indx_insert_into_buffer+0xaa3/0x13b0 fs/ntfs3/index.c:1755
indx_insert_entry+0x446/0x6b0 fs/ntfs3/index.c:1863
ntfs_create_inode+0x1d3f/0x35c0 fs/ntfs3/inode.c:1548
ntfs_create+0x3e/0x60 fs/ntfs3/namei.c:100
lookup_open fs/namei.c:3413 [inline]
If the member struct INDEX_BUFFER *index of struct indx_node is
incorrect, that is, the value of __le32 used is greater than the value
of __le32 total in struct INDEX_HDR. Therefore, OOB read occurs when
memmove is called in indx_insert_into_buffer().
Fix this by adding a check in hdr_find_e().
Fixes: 82cae269cf ("fs/ntfs3: Add initialization of super block")
Reported-by: syzbot+d882d57193079e379309@syzkaller.appspotmail.com
Signed-off-by: ZhangPeng <zhangpeng362@huawei.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6c3cef24c ]
Since the kmemdup may return NULL pointer,
it should be better to add check for the return value
in order to avoid NULL pointer dereference.
Fixes: b46acd6a6a ("fs/ntfs3: Add NTFS journal")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfa434c601 ]
Label ATTR_ROOT in ntfs_read_mft() sets is_root = true and
ni->ni_flags |= NI_FLAG_DIR, then next attr will goto label ATTR_ALLOC
and alloc ni->dir.alloc_run. However two states are not always
consistent and can make memory leak.
1) attr_name in ATTR_ROOT does not fit the condition it will set
is_root = true but NI_FLAG_DIR is not set.
2) next attr_name in ATTR_ALLOC fits the condition and alloc
ni->dir.alloc_run
3) in cleanup function ni_clear(), when NI_FLAG_DIR is set, it frees
ni->dir.alloc_run, otherwise it frees ni->file.run
4) because NI_FLAG_DIR is not set in this case, ni->dir.alloc_run is
leaked as kmemleak reported:
unreferenced object 0xffff888003bc5480 (size 64):
backtrace:
[<000000003d42e6b0>] __kmalloc_node+0x4e/0x1c0
[<00000000d8e19b8a>] kvmalloc_node+0x39/0x1f0
[<00000000fc3eb5b8>] run_add_entry+0x18a/0xa40 [ntfs3]
[<0000000011c9f978>] run_unpack+0x75d/0x8e0 [ntfs3]
[<00000000e7cf1819>] run_unpack_ex+0xbc/0x500 [ntfs3]
[<00000000bbf0a43d>] ntfs_iget5+0xb25/0x2dd0 [ntfs3]
[<00000000a6e50693>] ntfs_fill_super+0x218d/0x3580 [ntfs3]
[<00000000b9170608>] get_tree_bdev+0x3fb/0x710
[<000000004833798a>] vfs_get_tree+0x8e/0x280
[<000000006e20b8e6>] path_mount+0xf3c/0x1930
[<000000007bf15a5f>] do_mount+0xf3/0x110
...
Fix this by always setting is_root and NI_FLAG_DIR together.
Fixes: 82cae269cf ("fs/ntfs3: Add initialization of super block")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9168d125ea ]
'exists' looks like a boolean. This patch replaces it by the
normal name used for the rxe device, 'rxe', which should be a
little less confusing. The second rxe_dbg() message is
incorrect since rxe is known to be NULL and this will cause a
seg fault if this message were ever sent. Replace it by pr_debug
for the moment.
Fixes: c6aba5ea00 ("RDMA/rxe: Replace pr_xxx by rxe_dbg_xxx in rxe.c")
Link: https://lore.kernel.org/r/20230303221623.8053-2-rpearsonhpe@gmail.com
Signed-off-by: Bob Pearson <rpearsonhpe@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e6255fa3f ]
The VRTC alarm register can be programmed with an amount of seconds
after which the SoC will be woken up by the VRTC timer again. We are
already converting the alarm time from meson_vrtc_set_alarm() to
"seconds since 1970". This means we also need to use "seconds since
1970" for the current time.
This fixes a problem where setting the alarm to one minute in the future
results in the firmware (which handles wakeup) to output (on the serial
console) that the system will be woken up in billions of seconds.
ktime_get_raw_ts64() returns the time since boot, not since 1970. Switch
to ktime_get_real_ts64() to fix the calculation of the alarm time and to
make the SoC wake up at the specified date/time. Also the firmware
(which manages suspend) now prints either 59 or 60 seconds until wakeup
(depending on how long it takes for the system to enter suspend).
Fixes: 6ef35398e8 ("rtc: Add Amlogic Virtual Wake RTC")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20230320212142.2355062-1-martin.blumenstingl@googlemail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 335a42ebb0 ]
The workqueue watchdog prints a warning when there is no progress in
a worker pool. Where the progress means that the pool started processing
a pending work item.
Note that it is perfectly fine to process work items much longer.
The progress should be guaranteed by waking up or creating idle
workers.
show_one_worker_pool() prints state of non-idle worker pool. It shows
a delay since the last pool->watchdog_ts.
The timestamp is updated when a first pending work is queued in
__queue_work(). Also it is updated when a work is dequeued for
processing in worker_thread() and rescuer_thread().
The delay is misleading when there is no pending work item. In this
case it shows how long the last work item is being proceed. Show
zero instead. There is no stall if there is no pending work.
Fixes: 82607adcf9 ("workqueue: implement lockup detector")
Signed-off-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1d97a37f9 ]
The device_node pointer returned by of_find_compatible_node() with
refcount incremented, when finish using it, the refcount need be
decreased.
Fixes: d7964de8a8 ("clk: mediatek: Add new clock driver to handle FHCTL hardware")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221229092946.4162345-1-yangyingliang@huawei.com
[sboyd@kernel.org: Also unmap on error]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b73a0b80c6 ]
There is no need to check 'rdi->qp_dev' for NULL. The field 'qp_dev'
is created in rvt_register_device() which will fail if the 'qp_dev'
allocation fails in rvt_driver_qp_init(). Overwise this pointer
doesn't changed and passed to rvt_qp_exit() by the next step.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 0acb0cc7ec ("IB/rdmavt: Initialize and teardown of qpn table")
Signed-off-by: Natalia Petrova <n.petrova@fintech.ru>
Link: https://lore.kernel.org/r/20230303124408.16685-1-n.petrova@fintech.ru
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd98c93286 ]
The write index indicates which event the data is for and accesses a
per-file array. The index is passed by user processes during write()
calls as the first 4 bytes. Ensure that it cannot be negative by
returning -EINVAL to prevent out of bounds accesses.
Update ftrace self-test to ensure this occurs properly.
Link: https://lkml.kernel.org/r/20230425225107.8525-2-beaub@linux.microsoft.com
Fixes: 7f5a08c79d ("user_events: Add minimal support for trace_event into ftrace")
Reported-by: Doug Cook <dcook@linux.microsoft.com>
Signed-off-by: Beau Belgrave <beaub@linux.microsoft.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 82253a271a ]
The "Previous IRQ interference" line is misaligned and without
a \n, breaking the tool's output:
## CPU 12 hit stop tracing, analyzing it ##
Previous IRQ interference: up to 2.22 us IRQ handler delay: 18.06 us (0.00 %)
IRQ latency: 18.52 us
Timerlat IRQ duration: 4.41 us (0.00 %)
Blocking thread: 216.93 us (0.03 %)
Fix the output:
## CPU 7 hit stop tracing, analyzing it ##
Previous IRQ interference: up to 8.93 us
IRQ handler delay: 0.98 us (0.00 %)
IRQ latency: 2.95 us
Timerlat IRQ duration: 11.26 us (0.03 %)
Link: https://lore.kernel.org/linux-trace-devel/8b5819077f15ccf24745c9bf3205451e16ee32d9.1679685525.git.bristot@kernel.org
Fixes: 27e348b221 ("rtla/timerlat: Add auto-analysis core")
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Daniel Bristot de Oliveira <bristot@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f31dcb152a ]
Have local_clock() return sched_clock() if sched_clock_init() has not
yet run. sched_clock_cpu() has this check but it was not included in the
new noinstr implementation of local_clock().
The effect can be seen on x86 with CONFIG_PRINTK_TIME enabled, for
instance. scd->clock quickly reaches the value of TICK_NSEC and that
value is returned until sched_clock_init() runs.
dmesg without this patch:
[ 0.000000] kvm-clock: ...
[ 0.000002] kvm-clock: ...
[ 0.000672] clocksource: ...
[ 0.001000] tsc: ...
[ 0.001000] e820: ...
[ 0.001000] e820: ...
...
[ 0.001000] ..TIMER: ...
[ 0.001000] clocksource: ...
[ 0.378956] Calibrating delay loop ...
[ 0.379955] pid_max: ...
dmesg with this patch:
[ 0.000000] kvm-clock: ...
[ 0.000001] kvm-clock: ...
[ 0.000675] clocksource: ...
[ 0.002685] tsc: ...
[ 0.003331] e820: ...
[ 0.004190] e820: ...
...
[ 0.421939] ..TIMER: ...
[ 0.422842] clocksource: ...
[ 0.424582] Calibrating delay loop ...
[ 0.425580] pid_max: ...
Fixes: 776f22913b ("sched/clock: Make local_clock() noinstr")
Signed-off-by: Aaron Thompson <dev@aaront.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20230413175012.2201-1-dev@aaront.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit feffe5bb27 ]
Commit 95158a89dd ("sched,rt: Use the full cpumask for balancing")
allows find_lock_lowest_rq() to pick a task with migration disabled.
The purpose of the commit is to push the current running task on the
CPU that has the migrate_disable() task away.
However, there is a race which allows a migrate_disable() task to be
migrated. Consider:
CPU0 CPU1
push_rt_task
check is_migration_disabled(next_task)
task not running and
migration_disabled == 0
find_lock_lowest_rq(next_task, rq);
_double_lock_balance(this_rq, busiest);
raw_spin_rq_unlock(this_rq);
double_rq_lock(this_rq, busiest);
<<wait for busiest rq>>
<wakeup>
task become running
migrate_disable();
<context out>
deactivate_task(rq, next_task, 0);
set_task_cpu(next_task, lowest_rq->cpu);
WARN_ON_ONCE(is_migration_disabled(p));
Fixes: 95158a89dd ("sched,rt: Use the full cpumask for balancing")
Signed-off-by: Schspa Shi <schspa@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Reviewed-by: Valentin Schneider <vschneid@redhat.com>
Tested-by: Dwaine Gonyier <dgonyier@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e18398e80c ]
Commit 468af56a7b ("objtool: Support addition to set CFA base") was
added as a preparatory patch for arm64 support, but that support never
came. It triggers a false positive warning on x86, so just revert it
for now.
Fixes the following warning:
vmlinux.o: warning: objtool: cdce925_regmap_i2c_write+0xdb: stack state mismatch: cfa1=4+120 cfa2=5+40
Fixes: 468af56a7b ("objtool: Support addition to set CFA base")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/oe-kbuild-all/202304080538.j5G6h1AB-lkp@intel.com/
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15def34e26 ]
commit e050e3f0a7 ("perf: Fix broken interrupt rate throttling")
introduces a change in throttling threshold judgment. Before this,
compare hwc->interrupts and max_samples_per_tick, then increase
hwc->interrupts by 1, but this commit reverses order of these two
behaviors, causing the semantics of max_samples_per_tick to change.
In literal sense of "max_samples_per_tick", if hwc->interrupts ==
max_samples_per_tick, it should not be throttled, therefore, the judgment
condition should be changed to "hwc->interrupts > max_samples_per_tick".
In fact, this may cause the hardlockup to fail, The minimum value of
max_samples_per_tick may be 1, in this case, the return value of
__perf_event_account_interrupt function is 1.
As a result, nmi_watchdog gets throttled, which would stop PMU (Use x86
architecture as an example, see x86_pmu_handle_irq).
Fixes: e050e3f0a7 ("perf: Fix broken interrupt rate throttling")
Signed-off-by: Yang Jihong <yangjihong1@huawei.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20230227023508.102230-1-yangjihong1@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39afe5d6fc ]
There are scenarios where non-affine wakeups are incorrectly counted as
affine wakeups by schedstats.
When wake_affine_idle() returns prev_cpu which doesn't equal to
nr_cpumask_bits, it will slip through the check: target == nr_cpumask_bits
in wake_affine() and be counted as if target == this_cpu in schedstats.
Replace target == nr_cpumask_bits with target != this_cpu to make sure
affine wakeups are accurately tallied.
Fixes: 806486c377 (sched/fair: Do not migrate if the prev_cpu is idle)
Suggested-by: Daniel Jordan <daniel.m.jordan@oracle.com>
Signed-off-by: Libo Chen <libo.chen@oracle.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Link: https://lore.kernel.org/r/20220810223313.386614-1-libo.chen@oracle.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 271208ee5e ]
Using memcpy() isn't safe when buf is identical to rtas_err_buf, which
can happen during boot before slab is up. Full context which may not
be obvious from the diff:
if (altbuf) {
buf = altbuf;
} else {
buf = rtas_err_buf;
if (slab_is_available())
buf = kmalloc(RTAS_ERROR_LOG_MAX, GFP_ATOMIC);
}
if (buf)
memcpy(buf, rtas_err_buf, RTAS_ERROR_LOG_MAX);
This was found by inspection and I'm not aware of it causing problems
in practice. It appears to have been introduced by commit
033ef338b6 ("powerpc: Merge rtas.c into arch/powerpc/kernel"); the
old ppc64 version of this code did not have this problem.
Use memmove() instead.
Fixes: 033ef338b6 ("powerpc: Merge rtas.c into arch/powerpc/kernel")
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230220-rtas-queue-for-6-4-v1-2-010e4416f13f@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05dce4ba12 ]
LEDS_TRIGGER_DISK depends on ATA, so selecting LEDS_TRIGGER_DISK
when ATA is not set/enabled causes a Kconfig warning:
WARNING: unmet direct dependencies detected for LEDS_TRIGGER_DISK
Depends on [n]: NEW_LEDS [=y] && LEDS_TRIGGERS [=y] && ATA [=n]
Selected by [y]:
- ADB_PMU_LED_DISK [=y] && MACINTOSH_DRIVERS [=y] && ADB_PMU_LED [=y] && LEDS_CLASS [=y]
Fix this by making ADB_PMU_LED_DISK depend on ATA.
Seen on both PPC32 and PPC64.
Fixes: 0e865a80c1 ("macintosh: Remove dependency on IDE_GD_ATA if ADB_PMU_LED_DISK is selected")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230223014241.20878-1-rdunlap@infradead.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55d8bd02cc ]
Use "%pa" format specifier for resource_size_t to avoid a compiler
printk format warning.
arch/powerpc/sysdev/tsi108_pci.c: In function 'tsi108_setup_pci':
include/linux/kern_levels.h:5:25: error: format '%x' expects argument of type 'unsigned int', but argument 2 has type 'resource_size_t'
Fixes: c4342ff92b ("[POWERPC] Update mpc7448hpc2 board irq support using device tree")
Fixes: 2b9d7467a6 ("[POWERPC] Add tsi108 pci and platform device data register function")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
[mpe: Use pr_info() and unsplit string]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230223070116.660-5-rdunlap@infradead.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b69600d4d ]
Use "%pa" format specifier for resource_size_t to avoid compiler
printk format warnings.
../arch/powerpc/platforms/embedded6xx/flipper-pic.c: In function 'flipper_pic_init':
../include/linux/kern_levels.h:5:25: error: format '%x' expects argument of type 'unsigned int', but argument 2 has type 'resource_size_t' {aka 'long long unsigned int'} [-Werror=format=]
../arch/powerpc/platforms/embedded6xx/flipper-pic.c:148:9: note: in expansion of macro 'pr_info'
148 | pr_info("controller at 0x%08x mapped to 0x%p\n", res.start, io_base);
| ^~~~~~~
../arch/powerpc/platforms/embedded6xx/hlwd-pic.c: In function 'hlwd_pic_init':
../include/linux/kern_levels.h:5:25: error: format '%x' expects argument of type 'unsigned int', but argument 2 has type 'resource_size_t' {aka 'long long unsigned int'} [-Werror=format=]
../arch/powerpc/platforms/embedded6xx/hlwd-pic.c:174:9: note: in expansion of macro 'pr_info'
174 | pr_info("controller at 0x%08x mapped to 0x%p\n", res.start, io_base);
| ^~~~~~~
../arch/powerpc/platforms/embedded6xx/wii.c: In function 'wii_ioremap_hw_regs':
../include/linux/kern_levels.h:5:25: error: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'resource_size_t' {aka 'long long unsigned int'} [-Werror=format=]
../arch/powerpc/platforms/embedded6xx/wii.c:77:17: note: in expansion of macro 'pr_info'
77 | pr_info("%s at 0x%08x mapped to 0x%p\n", name,
| ^~~~~~~
Fixes: 028ee972f0 ("powerpc: gamecube/wii: flipper interrupt controller support")
Fixes: 9c21025c78 ("powerpc: wii: hollywood interrupt controller support")
Fixes: 5a7ee3198d ("powerpc: wii: platform support")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230223070116.660-3-rdunlap@infradead.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7538c97e2b ]
Use "%pa" format specifier for resource_size_t to avoid a compiler
printk format warning.
../arch/powerpc/platforms/512x/clock-commonclk.c: In function 'mpc5121_clk_provide_backwards_compat':
../arch/powerpc/platforms/512x/clock-commonclk.c:989:44: error: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'resource_size_t' {aka 'long long unsigned int'} [-Werror=format=]
989 | snprintf(devname, sizeof(devname), "%08x.%s", res.start, np->name); \
| ^~~~~~~~~ ~~~~~~~~~
| |
| resource_size_t {aka long long unsigned int}
Prevents 24 such warnings.
Fixes: 01f25c3716 ("clk: mpc512x: add backwards compat to the CCF code")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230223070116.660-2-rdunlap@infradead.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3a7a9ab65 ]
When dev_err_probe() is called, 'ret' holds the value of the previous
successful devm_request_irq() call.
'ret' should be assigned with a meaningful value before being used in
dev_err_probe().
While at it, use and return "PTR_ERR(ctrl->clk)" instead of a hard-coded
"-ENOENT" so that -EPROBE_DEFER is handled and propagated correctly.
Fixes: 81b6342056 ("fbdev: mmp: Make use of the helper function dev_err_probe()")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c0b057cec ]
In virtio_net, if we disable napi_tx, when we trigger a tx interrupt,
the vq->event_triggered will be set to true. It is then never reset
until we explicitly call virtqueue_enable_cb_delayed or
virtqueue_enable_cb_prepare.
If we disable the napi_tx, virtqueue_enable_cb* will only be called when
the tx ring is getting relatively empty.
Since event_triggered is true, VRING_AVAIL_F_NO_INTERRUPT or
VRING_PACKED_EVENT_FLAG_DISABLE will not be set. As a result we update
vring_used_event(&vq->split.vring) or vq->packed.vring.driver->off_wrap
every time we call virtqueue_get_buf_ctx. This causes more interrupts.
To summarize:
1) event_triggered was set to true in vring_interrupt()
2) after this nothing will happen in virtqueue_disable_cb() so
VRING_AVAIL_F_NO_INTERRUPT is not set in avail_flags_shadow
3) virtqueue_get_buf_ctx_split() will still think the cb is enabled
and then it will publish a new event index
To fix:
update VRING_AVAIL_F_NO_INTERRUPT or VRING_PACKED_EVENT_FLAG_DISABLE in
the vq when we call virtqueue_disable_cb even when event_triggered is
true.
Tested with iperf:
iperf3 tcp stream:
vm1 -----------------> vm2
vm2 just receives tcp data stream from vm1, and sends acks to vm1,
there are many tx interrupts in vm2.
with the patch applied there are just a few tx interrupts.
v2->v3:
-update the interrupt disable flag even with the event_triggered is set,
-instead of checking whether event_triggered is set in
-virtqueue_get_buf_ctx_{packed/split}, will cause the drivers which have
-not called virtqueue_{enable/disable}_cb to miss notifications.
v3->v4:
-remove change for
-"if (vq->packed.event_flags_shadow != VRING_PACKED_EVENT_FLAG_DISABLE)"
-in virtqueue_disable_cb_packed
Fixes: 8d622d21d2 ("virtio: fix up virtio_disable_cb")
Signed-off-by: Albert Huang <huangjie.albert@bytedance.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20230329102300.61000-1-huangjie.albert@bytedance.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c384c2401e ]
Current code ignores link state updates if VIRTIO_NET_F_STATUS was not
negotiated. However, link state updates could be received before feature
negotiation was completed , therefore causing link state events to be
lost, possibly leaving the link state down.
Modify the code so link state notifier is registered after DRIVER_OK was
negotiated and carry the registration only if
VIRTIO_NET_F_STATUS was negotiated. Unregister the notifier when the
device is reset.
Fixes: 033779a708 ("vdpa/mlx5: make MTU/STATUS presence conditional on feature bits")
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Eli Cohen <elic@nvidia.com>
Message-Id: <20230417110343.138319-1-elic@nvidia.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b56eef3e16 ]
When removing a SPMI driver, there can be a crash due to NULL pointer
dereference if it does not have a remove callback defined. This is
one such call trace observed when removing the QCOM SPMI PMIC driver:
dump_backtrace.cfi_jt+0x0/0x8
dump_stack_lvl+0xd8/0x16c
panic+0x188/0x498
__cfi_slowpath+0x0/0x214
__cfi_slowpath+0x1dc/0x214
spmi_drv_remove+0x16c/0x1e0
device_release_driver_internal+0x468/0x79c
driver_detach+0x11c/0x1a0
bus_remove_driver+0xc4/0x124
driver_unregister+0x58/0x84
cleanup_module+0x1c/0xc24 [qcom_spmi_pmic]
__do_sys_delete_module+0x3ec/0x53c
__arm64_sys_delete_module+0x18/0x28
el0_svc_common+0xdc/0x294
el0_svc+0x38/0x9c
el0_sync_handler+0x8c/0xf0
el0_sync+0x1b4/0x1c0
If a driver has all its resources allocated through devm_() APIs and
does not need any other explicit cleanup, it would not require a
remove callback to be defined. Hence, add a check for remove callback
presence before calling it when removing a SPMI driver.
Link: https://lore.kernel.org/r/1671601032-18397-2-git-send-email-quic_jprakash@quicinc.com
Fixes: 6f00f8c863 ("mfd: qcom-spmi-pmic: Use devm_of_platform_populate()")
Fixes: 5a86bf3439 ("spmi: Linux driver framework for SPMI")
Signed-off-by: Jishnu Prakash <quic_jprakash@quicinc.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20230413223834.4084793-7-sboyd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3fac2397f5 ]
When loading the driver for rtl8192e, the W_DISABLE# switch is working as
intended. But when the WLAN is turned off in software and then turned on
again the W_DISABLE# does not work anymore. Reason for this is that in
the function _rtl92e_dm_check_rf_ctrl_gpio() the bfirst_after_down is
checked and returned when true. bfirst_after_down is set true when
switching the WLAN off in software. But it is not set to false again
when WLAN is turned on again.
Add bfirst_after_down = false in _rtl92e_sta_up to reset bit and fix
above described bug.
Fixes: 94a799425e ("From: wlanfae <wlanfae@realtek.com> [PATCH 1/8] rtl8192e: Import new version of driver from realtek")
Signed-off-by: Philipp Hortmann <philipp.g.hortmann@gmail.com>
Link: https://lore.kernel.org/r/20230418200201.GA17398@matrix-ESPRIMO-P710
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be3206e890 ]
Using this macro makes the code more readable.
It also inits the members of dev_pm_ops in the following manner
without us explicitly needing to:
.suspend = cqspi_suspend, \
.resume = cqspi_resume, \
.freeze = cqspi_suspend, \
.thaw = cqspi_resume, \
.poweroff = cqspi_suspend, \
.restore = cqspi_resume
Also get rid of conditional compilation based on CONFIG_PM_SLEEP because
it introduces build issues with certain configs when CQSPI_DEV_PM_OPS is
just NULL.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/oe-kbuild-all/202304191900.2fARFQW9-lkp@intel.com/
Fixes: 1406234105 ("mtd: spi-nor: Add driver for Cadence Quad SPI Flash Controller")
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230420054257.925092-1-d-gole@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d28f4091ea ]
When handle qmu transfer irq, it will unlock @mtu->lock before give back
request, if another thread handle disconnect event at the same time, and
try to disable ep, it may lock @mtu->lock and free qmu ring, then qmu
irq hanlder may get a NULL gpd, avoid the KE by checking gpd's value before
handling it.
e.g.
qmu done irq on cpu0 thread running on cpu1
qmu_done_tx()
handle gpd [0]
mtu3_requ_complete() mtu3_gadget_ep_disable()
unlock @mtu->lock
give back request lock @mtu->lock
mtu3_ep_disable()
mtu3_gpd_ring_free()
unlock @mtu->lock
lock @mtu->lock
get next gpd [1]
[1]: goto [0] to handle next gpd, and next gpd may be NULL.
Fixes: 48e0d3735a ("usb: mtu3: supports new QMU format")
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20230417025203.18097-3-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5629d31955 ]
Commit ac82b56bda ("usb: gadget: tegra-xudc: Add vbus_draw support")
populated the vbus_draw callback for the Tegra XUDC driver. The function
tegra_xudc_gadget_vbus_draw(), that was added by this commit, assumes
that the pointer 'curr_usbphy' has been initialised, which is not always
the case because this is only initialised when the USB role is updated.
Fix this crash, by checking that the 'curr_usbphy' is valid before
dereferencing.
Fixes: ac82b56bda ("usb: gadget: tegra-xudc: Add vbus_draw support")
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20230405181854.42355-1-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 80f746e2bd ]
The Store Queue code allocates a bitmap buffer with the size of
multiple of sizeof(long) in sq_api_init(). While the buffer size
is calculated correctly, the code uses the wrong element size to
allocate the buffer which results in the allocated bitmap buffer
being too small.
Fix this by allocating the buffer with kcalloc() with element size
sizeof(long) instead of kzalloc() whose elements size defaults to
sizeof(char).
Fixes: d7c30c682a ("sh: Store Queue API rework.")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Link: https://lore.kernel.org/r/20230419114854.528677-1-glaubitz@physik.fu-berlin.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31088f6f79 ]
typeof is (still) a GNU extension, which means that it cannot be used when
building ISO C (e.g. -std=c99). It should therefore be avoided in uapi
headers in favour of the ISO-friendly __typeof__.
Unfortunately this issue could not be detected by
CONFIG_UAPI_HEADER_TEST=y as the __ALIGN_KERNEL() macro is not expanded in
any uapi header.
This matters from a userspace perspective, not a kernel one. uapi
headers and their contents are expected to be usable in a variety of
situations, and in particular when building ISO C applications (with
-std=c99 or similar).
This particular problem can be reproduced by trying to use the
__ALIGN_KERNEL macro directly in application code, say:
#include <linux/const.h>
int align(int x, int a)
{
return __KERNEL_ALIGN(x, a);
}
and trying to build that with -std=c99.
Link: https://lkml.kernel.org/r/20230411092747.3759032-1-kevin.brodsky@arm.com
Fixes: a79ff731a1 ("netfilter: xtables: make XT_ALIGN() usable in exported headers by exporting __ALIGN_KERNEL()")
Signed-off-by: Kevin Brodsky <kevin.brodsky@arm.com>
Reported-by: Ruben Ayrapetyan <ruben.ayrapetyan@arm.com>
Tested-by: Ruben Ayrapetyan <ruben.ayrapetyan@arm.com>
Reviewed-by: Petr Vorel <pvorel@suse.cz>
Tested-by: Petr Vorel <pvorel@suse.cz>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8af055ae25 ]
If CONFIG_DEBUG_INFO_REDUCED is enabled in the kernel configuration, we
will typically not be able to load vmlinux-gdb.py and will fail with:
Traceback (most recent call last):
File "/home/fainelli/work/buildroot/output/arm64/build/linux-custom/vmlinux-gdb.py", line 25, in <module>
import linux.utils
File "/home/fainelli/work/buildroot/output/arm64/build/linux-custom/scripts/gdb/linux/utils.py", line 131, in <module>
atomic_long_counter_offset = atomic_long_type.get_type()['counter'].bitpos
KeyError: 'counter'
Rather be left wondering what is happening only to find out that reduced
debug information is the cause, raise an eror. This was not typically a
problem until e3c8d33e0d ("scripts/gdb: fix 'lx-dmesg' on 32 bits arch")
but it has since then.
Link: https://lkml.kernel.org/r/20230406215252.1580538-1-f.fainelli@gmail.com
Fixes: e3c8d33e0d ("scripts/gdb: fix 'lx-dmesg' on 32 bits arch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: Antonio Borneo <antonio.borneo@foss.st.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: John Ogness <john.ogness@linutronix.de>
Cc: Kieran Bingham <kbingham@kernel.org>
Cc: Petr Mladek <pmladek@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d663d93bb4 ]
The xiic_xfer() function gets a runtime PM reference when the function is
entered. This reference is released when the function is exited. There is
currently one error path where the function exits directly, which leads to
a leak of the runtime PM reference.
Make sure that this error path also releases the runtime PM reference.
Fixes: fdacc3c740 ("i2c: xiic: Switch from waitqueue to completion")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae1664f04f ]
The cdns_i2c_master_xfer() function gets a runtime PM reference when the
function is entered. This reference is released when the function is
exited. There is currently one error path where the function exits
directly, which leads to a leak of the runtime PM reference.
Make sure that this error path also releases the runtime PM reference.
Fixes: 1a351b10b9 ("i2c: cadence: Added slave support")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2087e85bb6 ]
The cadence QSPI driver misbehaves after performing a full system suspend
resume:
...
spi-nor spi0.0: resume() failed
...
This results in a flash connected via OSPI interface after system suspend-
resume to be unusable.
fix these suspend and resume functions.
Fixes: 1406234105 ("mtd: spi-nor: Add driver for Cadence Quad SPI Flash Controller")
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230417091027.966146-3-d-gole@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5a6dd2624 ]
Assignment of NVIDIA Ampere-based GPUs have seen a regression since the
below referenced commit, where the reduced D3hot transition delay appears
to introduce a small window where a D3hot->D0 transition followed by a bus
reset can wedge the device. The entire device is subsequently unavailable,
returning -1 on config space read and is unrecoverable without a host
reset.
This has been observed with RTX A2000 and A5000 GPU and audio functions
assigned to a Windows VM, where shutdown of the VM places the devices in
D3hot prior to vfio-pci performing a bus reset when userspace releases the
devices. The issue has roughly a 2-3% chance of occurring per shutdown.
Restoring the HDA controller d3hot_delay to the effective value before the
below commit has been shown to resolve the issue. NVIDIA confirms this
change should be safe for all of their HDA controllers.
Fixes: 3e347969a5 ("PCI/PM: Reduce D3hot delay with usleep_range()")
Link: https://lore.kernel.org/r/20230413194042.605768-1-alex.williamson@redhat.com
Reported-by: Zhiyi Guo <zhguo@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tarun Gupta <targupta@nvidia.com>
Cc: Abhishek Sahu <abhsahu@nvidia.com>
Cc: Tarun Gupta <targupta@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c34890273 ]
of_node_put() should have been done directly after
mqs_priv->regmap = syscon_node_to_regmap(gpr_np);
otherwise it creates a reference leak on the success path.
To fix this, of_node_put() is moved to the correct location, and change
all the gotos to direct returns.
Fixes: a9d2736714 ("ASoC: fsl_mqs: Fix error handling in probe")
Signed-off-by: Liliang Ye <yll@hust.edu.cn>
Reviewed-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/r/20230403152647.17638-1-yll@hust.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cde0fbff07 ]
If a Device Tree (DT) is used, the presence of cache properties is
assumed. Not finding any is not considered. For arm64 platforms,
cache information can be fetched from the clidr_el1 register.
Checking whether cache information is available in the DT
allows to switch to using clidr_el1.
init_of_cache_level()
\-of_count_cache_leaves()
will assume there a 2 cache leaves (L1 data/instruction caches), which
can be different from clidr_el1 information.
cache_setup_of_node() tries to read cache properties in the DT.
If there are none, this is considered a success. Knowing no
information was available would allow to switch to using clidr_el1.
Fixes: de0df442ee ("cacheinfo: Check 'cache-unified' property to count cache leaves")
Reported-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Link: https://lore.kernel.org/all/20230404-hatred-swimmer-6fecdf33b57a@spud/
Signed-off-by: Pierre Gondois <pierre.gondois@arm.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230414081453.244787-3-pierre.gondois@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a306e3eab ]
If there is no ACPI/DT information, it is assumed that L1 caches
are private and L2 (and higher) caches are shared. A cache is
'shared' between two CPUs if it is accessible from these two
CPUs.
Each CPU owns a representation (i.e. has a dedicated cacheinfo struct)
of the caches it has access to. cache_leaves_are_shared() tries to
identify whether two representations are designating the same actual
cache.
In cache_leaves_are_shared(), if 'this_leaf' is a L2 cache (or higher)
and 'sib_leaf' is a L1 cache, the caches are detected as shared as
only this_leaf's cache level is checked.
This is leads to setting sib_leaf as being shared with another CPU,
which is incorrect as this is a L1 cache.
Check 'sib_leaf->level'. Also update the comment as the function is
called when populating 'shared_cpu_map'.
Fixes: f16d1becf9 ("cacheinfo: Use cache identifiers to check if the caches are shared if available")
Signed-off-by: Pierre Gondois <pierre.gondois@arm.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230414081453.244787-2-pierre.gondois@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8455cbb259 ]
Based on num_hid_devices, each sensor device is initialized. If
"no sensors" is initialized, amd_sfh work initialization and scheduling
doesn’t make sense and returns EOPNOTSUPP to stop driver probe. Hence,
add a check for "no sensors" enabled to handle the special case.
Fixes: 93ce5e0231 ("HID: amd_sfh: Implement SFH1.1 functionality")
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 571dc8f59d ]
The initialization of SFH1.1 sensors may take some time. Hence, increase
sensor command timeouts in order to obtain status responses within a
maximum timeout.
Fixes: 93ce5e0231 ("HID: amd_sfh: Implement SFH1.1 functionality")
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 82c2a0d137 ]
Misinterpreted the stop all command in SHF1.1 firmware. Therefore, it is
necessary to update the stop all command accordingly to disable all
sensors.
Fixes: 93ce5e0231 ("HID: amd_sfh: Implement SFH1.1 functionality")
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1353ecaf18 ]
As soon as the system is booted after shutdown, the sensors may remain in
a weird state and fail to initialize. Therefore, all sensors should be
turned off during shutdown.
Fixes: 4f567b9f81 ("SFH: PCIe driver to add support of AMD sensor fusion hub")
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b9255bf11 ]
In order to start or stop sensors, the firmware command needs to be
changed to add an additional default subcommand value. For this reason,
add a subcommand value to enable or disable sensors accordingly.
Fixes: 93ce5e0231 ("HID: amd_sfh: Implement SFH1.1 functionality")
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0de155752b ]
When CONFIG_PROC_FS is not set, proc_salinfo_show() is not used. Mark the
function as __maybe_unused to quieten the warning message.
../arch/ia64/kernel/salinfo.c:584:12: warning: 'proc_salinfo_show' defined but not used [-Wunused-function]
584 | static int proc_salinfo_show(struct seq_file *m, void *v)
| ^~~~~~~~~~~~~~~~~
Link: https://lkml.kernel.org/r/20230223034309.13375-1-rdunlap@infradead.org
Fixes: 3f3942aca6 ("proc: introduce proc_create_single{,_data}")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58deeb4ef3 ]
alloc_per_cpu_data() is called by find_memory(), which is marked as
__init. Therefore alloc_per_cpu_data() can also be marked as __init to
remedy this modpost problem.
WARNING: modpost: vmlinux.o: section mismatch in reference: alloc_per_cpu_data (section: .text) -> memblock_alloc_try_nid (section: .init.text)
Link: https://lkml.kernel.org/r/20230223034258.12917-1-rdunlap@infradead.org
Fixes: 4b9ddc7cf2 ("[IA64] Fix section mismatch in contig.c version of per_cpu_init()")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c441b1e03d ]
During EDR recovery, the OS must clear error status of the port that
triggered DPC even if firmware retains control of DPC and AER (see the
implementation note in the PCI Firmware spec r3.3, sec 4.6.12).
Prior to 068c29a248 ("PCI/ERR: Clear PCIe Device Status errors only if
OS owns AER"), the port Device Status was cleared in this path:
edr_handle_event
dpc_process_error(dev) # "dev" triggered DPC
pcie_do_recovery(dev, dpc_reset_link)
dpc_reset_link # exit DPC
pcie_clear_device_status(dev) # clear Device Status
After 068c29a248, pcie_do_recovery() no longer clears Device Status when
firmware controls AER, so the error bit remains set even after recovery.
Per the "Downstream Port Containment configuration control" bit in the
returned _OSC Control Field (sec 4.5.1), the OS is allowed to clear error
status until it evaluates _OST, so clear Device Status in
edr_handle_event() if the error recovery was successful.
[bhelgaas: commit log]
Fixes: 068c29a248 ("PCI/ERR: Clear PCIe Device Status errors only if OS owns AER")
Link: https://lore.kernel.org/r/20230315235449.1279209-1-sathyanarayanan.kuppuswamy@linux.intel.com
Reported-by: Tsaur Erwin <erwin.tsaur@intel.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b19a4266c5 ]
The helper generating an OF based modalias (of_device_get_modalias())
works fine, but due to the use of snprintf() internally it needs a
buffer one byte longer than what should be needed just for the entire
string (excluding the '\0'). Most users of this helper are sysfs hooks
providing the modalias string to users. They all provide a PAGE_SIZE
buffer which is way above the number of bytes required to fit the
modalias string and hence do not suffer from this issue.
There is another user though, of_device_request_module(), which is only
called by drivers/usb/common/ulpi.c. This request module function is
faulty, but maybe because in most cases there is an alternative, ULPI
driver users have not noticed it.
In this function, of_device_get_modalias() is called twice. The first
time without buffer just to get the number of bytes required by the
modalias string (excluding the null byte), and a second time, after
buffer allocation, to fill the buffer. The allocation asks for an
additional byte, in order to store the trailing '\0'. However, the
buffer *length* provided to of_device_get_modalias() excludes this extra
byte. The internal use of snprintf() with a length that is exactly the
number of bytes to be written has the effect of using the last available
byte to store a '\0', which then smashes the last character of the
modalias string.
Provide the actual size of the buffer to of_device_get_modalias() to fix
this issue.
Note: the "str[size - 1] = '\0';" line is not really needed as snprintf
will anyway end the string with a null byte, but there is a possibility
that this function might be called on a struct device_node without
compatible, in this case snprintf() would not be executed. So we keep it
just to avoid possible unbounded strings.
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Peter Chen <peter.chen@kernel.org>
Fixes: 9c829c097f ("of: device: Support loading a module with OF based modalias")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230404172148.82422-2-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae13381da5 ]
During fuzzing, a general protection fault is observed in
vmci_host_poll().
general protection fault, probably for non-canonical address 0xdffffc0000000019: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x00000000000000c8-0x00000000000000cf]
RIP: 0010:__lock_acquire+0xf3/0x5e00 kernel/locking/lockdep.c:4926
<- omitting registers ->
Call Trace:
<TASK>
lock_acquire+0x1a4/0x4a0 kernel/locking/lockdep.c:5672
__raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:110 [inline]
_raw_spin_lock_irqsave+0xb3/0x100 kernel/locking/spinlock.c:162
add_wait_queue+0x3d/0x260 kernel/sched/wait.c:22
poll_wait include/linux/poll.h:49 [inline]
vmci_host_poll+0xf8/0x2b0 drivers/misc/vmw_vmci/vmci_host.c:174
vfs_poll include/linux/poll.h:88 [inline]
do_pollfd fs/select.c:873 [inline]
do_poll fs/select.c:921 [inline]
do_sys_poll+0xc7c/0x1aa0 fs/select.c:1015
__do_sys_ppoll fs/select.c:1121 [inline]
__se_sys_ppoll+0x2cc/0x330 fs/select.c:1101
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x4e/0xa0 arch/x86/entry/common.c:82
entry_SYSCALL_64_after_hwframe+0x46/0xb0
Example thread interleaving that causes the general protection fault
is as follows:
CPU1 (vmci_host_poll) CPU2 (vmci_host_do_init_context)
----- -----
// Read uninitialized context
context = vmci_host_dev->context;
// Initialize context
vmci_host_dev->context = vmci_ctx_create();
vmci_host_dev->ct_type = VMCIOBJ_CONTEXT;
if (vmci_host_dev->ct_type == VMCIOBJ_CONTEXT) {
// Dereferencing the wrong pointer
poll_wait(..., &context->host_context);
}
In this scenario, vmci_host_poll() reads vmci_host_dev->context first,
and then reads vmci_host_dev->ct_type to check that
vmci_host_dev->context is initialized. However, since these two reads
are not atomically executed, there is a chance of a race condition as
described above.
To fix this race condition, read vmci_host_dev->context after checking
the value of vmci_host_dev->ct_type so that vmci_host_poll() always
reads an initialized context.
Reported-by: Dae R. Jeong <threeearcat@gmail.com>
Fixes: 8bf503991f ("VMCI: host side driver implementation.")
Signed-off-by: Dae R. Jeong <threeearcat@gmail.com>
Link: https://lore.kernel.org/r/ZCGFsdBAU4cYww5l@dragonet
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39db65a0a1 ]
The driver is able to work fine without relying on a mandatory interrupt
being assigned to the I2C device. This is only needed when making use of
the jack-detect support.
However, the following warning message is always emitted when there is
no such interrupt available:
es8316 0-0011: Failed to get IRQ 0: -22
Do not attempt to request an IRQ if it is not available/valid. This also
ensures the rather misleading message is not displayed anymore.
Also note the IRQ validation relies on commit dab472eb93 ("i2c /
ACPI: Use 0 to indicate that device does not have interrupt assigned").
Fixes: 8222576610 ("ASoC: es8316: Add jack-detect support")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230328094901.50763-1-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f5ac460df ]
commit bb38919ec5 ("PCI: imx6: Add support for i.MX6 PCIe controller")
added a fault hook to this driver in the probe function. So it was only
installed if needed.
commit bde4a5a00e ("PCI: imx6: Allow probe deferral by reset GPIO")
moved it from probe to driver init which installs the hook unconditionally
as soon as the driver is compiled into a kernel.
When this driver is compiled as a module, the hook is not registered
until after the driver has been matched with a .compatible and
loaded.
commit 415b6185c5 ("PCI: imx6: Fix config read timeout handling")
extended the fault handling code.
commit 2d8ed461db ("PCI: imx6: Add support for i.MX8MQ")
added some protection for non-ARM architectures, but this does not
protect non-i.MX ARM architectures.
Since fault handlers can be triggered on any architecture for different
reasons, there is no guarantee that they will be triggered only for the
assumed situation, leading to improper error handling (i.MX6-specific
imx6q_pcie_abort_handler) on foreign systems.
I had seen strange L3 imprecise external abort messages several times on
OMAP4 and OMAP5 devices and couldn't make sense of them until I realized
they were related to this unused imx6q driver because I had
CONFIG_PCI_IMX6=y.
Note that CONFIG_PCI_IMX6=y is useful for kernel binaries that are designed
to run on different ARM SoC and be differentiated only by device tree
binaries. So turning off CONFIG_PCI_IMX6 is not a solution.
Therefore we check the compatible in the init function before registering
the fault handler.
Link: https://lore.kernel.org/r/e1bcfc3078c82b53aa9b78077a89955abe4ea009.1678380991.git.hns@goldelico.com
Fixes: bde4a5a00e ("PCI: imx6: Allow probe deferral by reset GPIO")
Fixes: 415b6185c5 ("PCI: imx6: Fix config read timeout handling")
Fixes: 2d8ed461db ("PCI: imx6: Add support for i.MX8MQ")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37b58becc1 ]
After commit bbf7d3b1c4 ("ASoC: soc-pcm: align BE 'atomicity' with
that of the FE") BE and FE atomicity must match.
In the case of Compress PCM there is a mismatch in atomicity between FE
and BE and we get errors like this:
[ 36.434566] sai1-wm8960-hifi: dpcm_be_connect: FE is atomic but BE
is nonatomic, invalid configuration
[ 36.444278] PCM Deep Buffer: ASoC: can't connect SAI1.OUT
In order to fix this we must inherit the atomicity from DAI link
associated with current PCM Compress FE.
Fixes: bbf7d3b1c4 ("ASoC: soc-pcm: align BE 'atomicity' with that of the FE")
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230324124019.30826-1-daniel.baluta@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b947f8769 ]
In renesas_usb3_probe, role_work is bound with renesas_usb3_role_work.
renesas_usb3_start will be called to start the work.
If we remove the driver which will call usbhs_remove, there may be
an unfinished work. The possible sequence is as follows:
CPU0 CPU1
renesas_usb3_role_work
renesas_usb3_remove
usb_role_switch_unregister
device_unregister
kfree(sw)
//free usb3->role_sw
usb_role_switch_set_role
//use usb3->role_sw
The usb3->role_sw could be freed under such circumstance and then
used in usb_role_switch_set_role.
This bug was found by static analysis. And note that removing a
driver is a root-only operation, and should never happen in normal
case. But the root user may directly remove the device which
will also trigger the remove function.
Fix it by canceling the work before cleanup in the renesas_usb3_remove.
Fixes: 39facfa01c ("usb: gadget: udc: renesas_usb3: Add register of usb role switch")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20230320062931.505170-1-zyytlz.wz@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c17655ab1 ]
Use kunmap_local() to unmap pages locally mapped with kmap_local_page().
kunmap_local() must be called on the kernel virtual address returned by
kmap_local_page(), differently from how we use kunmap() which instead
expects the mapped page as its argument.
In module_zstd_decompress() we currently map with kmap_local_page() and
unmap with kunmap(). This breaks the code and so it should be fixed.
Cc: Piotr Gorski <piotrgorski@cachyos.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Ira Weiny <ira.weiny@intel.com>
Fixes: 169a58ad82 ("module/decompress: Support zstd in-kernel decompression")
Signed-off-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Piotr Gorski <piotrgorski@cachyos.org>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9448bc1dee ]
An early error exit in atmel_qspi_remove() doesn't prevent the device
unbind. So this results in an spi controller with an unbound parent
and unmapped register space (because devm_ioremap_resource() is undone).
So using the remaining spi controller probably results in an oops.
Instead unregister the controller unconditionally and only skip hardware
access and clk disable.
Also add a warning about resume failing and return zero unconditionally.
The latter has the only effect to suppress a less helpful error message by
the spi core.
Fixes: 4a2f83b7f7 ("spi: atmel-quadspi: add runtime pm support")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20230317084232.142257-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15ac1122fd ]
The arbitration of the UART DMA is mishandled for a few
exceptional cases when probing and releasing the driver.
It is possible that the DMA register spaces are not defined in
device tree for an instance of the driver, so attempts to access
the registers in brcmuart_arbitration() would use NULL pointers.
It is also possible for the probe function to return an error
while still holding the UART DMA. This would prevent the UART
DMA from being claimed by an instance that could use it.
These errors are addressed by only releasing the UART DMA if it
is held by this instance (i.e. priv->dma_enabled == 1) and
directing early error paths in probe to this common release_dma
handling.
Fixes: 41a469482d ("serial: 8250: Add new 8250-core based Broadcom STB driver")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230309190224.687380-1-opendmb@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c47527cbcc ]
The stm32_usart_transmit_chars() may be called with empty or stopped
transmit queue, and no XON/OFF character pending. This can happen at
the end of transmission, where this last call is used to either handle
the XON/XOFF x_char, or disable TX interrupt if queue is empty or
stopped.
If that occurs, do not assert the RS485 RTS/DE GPIO anymore, as the
GPIO would remain asserted past the end of transmission and that would
block the RS485 bus after the transmission.
Only assert the RS485 RTS/DE GPIO if there is either pending XON/XOFF
x_char, or at least one character in running transmit queue.
Fixes: d7c7671616 ("serial: stm32: Use TC interrupt to deassert GPIO RTS in RS485 mode")
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20230223042252.95480-2-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4decf4060e ]
Currently we process the suspend interrupt event only if the
device is in configured state. Consider a case where device
is not configured and got suspend interrupt, in that case our
gadget will still use 100mA as composite_suspend didn't happen.
But battery charging specification (BC1.2) expects a downstream
device to draw less than 2.5mA when unconnected OR suspended.
Fix this by removing the condition for processing suspend event,
and thus composite_resume would set vbus draw to 2.
Fixes: 72704f876f ("dwc3: gadget: Implement the suspend entry event handler")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/1677217619-10261-2-git-send-email-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5239a89b06 ]
This reverts commit 76d62f24db.
So while priority inversion on the pmsg_lock is an occasional
problem that an rt_mutex would help with, in uses where logging
is writing to pmsg heavily from multiple threads, the pmsg_lock
can be heavily contended.
After this change landed, it was reported that cases where the
mutex locking overhead was commonly adding on the order of 10s
of usecs delay had suddenly jumped to ~msec delay with rtmutex.
It seems the slight differences in the locks under this level
of contention causes the normal mutexes to utilize the spinning
optimizations, while the rtmutexes end up in the sleeping
slowpath (which allows additional threads to pile on trying
to take the lock).
In this case, it devolves to a worse case senerio where the lock
acquisition and scheduling overhead dominates, and each thread
is waiting on the order of ~ms to do ~us of work.
Obviously, having tons of threads all contending on a single
lock for logging is non-optimal, so the proper fix is probably
reworking pstore pmsg to have per-cpu buffers so we don't have
contention.
Additionally, Steven Rostedt has provided some furhter
optimizations for rtmutexes that improves the rtmutex spinning
path, but at least in my testing, I still see the test tripping
into the sleeping path on rtmutexes while utilizing the spinning
path with mutexes.
But in the short term, lets revert the change to the rt_mutex
and go back to normal mutexes to avoid a potentially major
performance regression. And we can work on optimizations to both
rtmutexes and finer-grained locking for pstore pmsg in the
future.
Cc: Wei Wang <wvw@google.com>
Cc: Midas Chien<midaschieh@google.com>
Cc: "Chunhui Li (李春辉)" <chunhui.li@mediatek.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: "Guilherme G. Piccoli" <gpiccoli@igalia.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: kernel-team@android.com
Fixes: 76d62f24db ("pstore: Switch pmsg_lock to an rt_mutex to avoid priority inversion")
Reported-by: "Chunhui Li (李春辉)" <chunhui.li@mediatek.com>
Signed-off-by: John Stultz <jstultz@google.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230308204043.2061631-1-jstultz@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f46703609 ]
Commit cc7ad0d77b ("drivers: staging: rtl8723bs: Fix deadlock in
rtw_surveydone_event_callback()") besides fixing the deadlock also
modified rtw_scan_timeout_handler() to use spin_[un]lock_irq()
instead of spin_[un]lock_bh().
Disabling the IRQs is not necessary since all code taking this lock
runs from either user contexts or from softirqs
rtw_scan_timeout_handler() is the only function taking pmlmepriv->lock
which uses spin_[un]lock_irq() for this. Switch back to
spin_[un]lock_bh() to make it consistent with the rest of the code.
Fixes: cc7ad0d77b ("drivers: staging: rtl8723bs: Fix deadlock in rtw_surveydone_event_callback()")
Cc: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230221145326.7808-2-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 215792eda0 ]
Commit 041879b12d ("drivers: staging: rtl8192bs: Fix deadlock in
rtw_joinbss_event_prehandle()") besides fixing the deadlock also
modified _rtw_join_timeout_handler() to use spin_[un]lock_irq()
instead of spin_[un]lock_bh().
_rtw_join_timeout_handler() calls rtw_do_join() which takes
pmlmepriv->scanned_queue.lock using spin_[un]lock_bh(). This
spin_unlock_bh() call re-enables softirqs which triggers an oops in
kernel/softirq.c: __local_bh_enable_ip() when it calls
lockdep_assert_irqs_enabled():
[ 244.506087] WARNING: CPU: 2 PID: 0 at kernel/softirq.c:376 __local_bh_enable_ip+0xa6/0x100
...
[ 244.509022] Call Trace:
[ 244.509048] <IRQ>
[ 244.509100] _rtw_join_timeout_handler+0x134/0x170 [r8723bs]
[ 244.509468] ? __pfx__rtw_join_timeout_handler+0x10/0x10 [r8723bs]
[ 244.509772] ? __pfx__rtw_join_timeout_handler+0x10/0x10 [r8723bs]
[ 244.510076] call_timer_fn+0x95/0x2a0
[ 244.510200] __run_timers.part.0+0x1da/0x2d0
This oops is causd by the switch to spin_[un]lock_irq() which disables
the IRQs for the entire duration of _rtw_join_timeout_handler().
Disabling the IRQs is not necessary since all code taking this lock
runs from either user contexts or from softirqs, switch back to
spin_[un]lock_bh() to fix this.
Fixes: 041879b12d ("drivers: staging: rtl8192bs: Fix deadlock in rtw_joinbss_event_prehandle()")
Cc: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230221145326.7808-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50749f2dd6 ]
syzkaller reported [0] memory leaks of an UDP socket and ZEROCOPY
skbs. We can reproduce the problem with these sequences:
sk = socket(AF_INET, SOCK_DGRAM, 0)
sk.setsockopt(SOL_SOCKET, SO_TIMESTAMPING, SOF_TIMESTAMPING_TX_SOFTWARE)
sk.setsockopt(SOL_SOCKET, SO_ZEROCOPY, 1)
sk.sendto(b'', MSG_ZEROCOPY, ('127.0.0.1', 53))
sk.close()
sendmsg() calls msg_zerocopy_alloc(), which allocates a skb, sets
skb->cb->ubuf.refcnt to 1, and calls sock_hold(). Here, struct
ubuf_info_msgzc indirectly holds a refcnt of the socket. When the
skb is sent, __skb_tstamp_tx() clones it and puts the clone into
the socket's error queue with the TX timestamp.
When the original skb is received locally, skb_copy_ubufs() calls
skb_unclone(), and pskb_expand_head() increments skb->cb->ubuf.refcnt.
This additional count is decremented while freeing the skb, but struct
ubuf_info_msgzc still has a refcnt, so __msg_zerocopy_callback() is
not called.
The last refcnt is not released unless we retrieve the TX timestamped
skb by recvmsg(). Since we clear the error queue in inet_sock_destruct()
after the socket's refcnt reaches 0, there is a circular dependency.
If we close() the socket holding such skbs, we never call sock_put()
and leak the count, sk, and skb.
TCP has the same problem, and commit e0c8bccd40 ("net: stream:
purge sk_error_queue in sk_stream_kill_queues()") tried to fix it
by calling skb_queue_purge() during close(). However, there is a
small chance that skb queued in a qdisc or device could be put
into the error queue after the skb_queue_purge() call.
In __skb_tstamp_tx(), the cloned skb should not have a reference
to the ubuf to remove the circular dependency, but skb_clone() does
not call skb_copy_ubufs() for zerocopy skb. So, we need to call
skb_orphan_frags_rx() for the cloned skb to call skb_copy_ubufs().
[0]:
BUG: memory leak
unreferenced object 0xffff88800c6d2d00 (size 1152):
comm "syz-executor392", pid 264, jiffies 4294785440 (age 13.044s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 cd af e8 81 00 00 00 00 ................
02 00 07 40 00 00 00 00 00 00 00 00 00 00 00 00 ...@............
backtrace:
[<0000000055636812>] sk_prot_alloc+0x64/0x2a0 net/core/sock.c:2024
[<0000000054d77b7a>] sk_alloc+0x3b/0x800 net/core/sock.c:2083
[<0000000066f3c7e0>] inet_create net/ipv4/af_inet.c:319 [inline]
[<0000000066f3c7e0>] inet_create+0x31e/0xe40 net/ipv4/af_inet.c:245
[<000000009b83af97>] __sock_create+0x2ab/0x550 net/socket.c:1515
[<00000000b9b11231>] sock_create net/socket.c:1566 [inline]
[<00000000b9b11231>] __sys_socket_create net/socket.c:1603 [inline]
[<00000000b9b11231>] __sys_socket_create net/socket.c:1588 [inline]
[<00000000b9b11231>] __sys_socket+0x138/0x250 net/socket.c:1636
[<000000004fb45142>] __do_sys_socket net/socket.c:1649 [inline]
[<000000004fb45142>] __se_sys_socket net/socket.c:1647 [inline]
[<000000004fb45142>] __x64_sys_socket+0x73/0xb0 net/socket.c:1647
[<0000000066999e0e>] do_syscall_x64 arch/x86/entry/common.c:50 [inline]
[<0000000066999e0e>] do_syscall_64+0x38/0x90 arch/x86/entry/common.c:80
[<0000000017f238c1>] entry_SYSCALL_64_after_hwframe+0x63/0xcd
BUG: memory leak
unreferenced object 0xffff888017633a00 (size 240):
comm "syz-executor392", pid 264, jiffies 4294785440 (age 13.044s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 2d 6d 0c 80 88 ff ff .........-m.....
backtrace:
[<000000002b1c4368>] __alloc_skb+0x229/0x320 net/core/skbuff.c:497
[<00000000143579a6>] alloc_skb include/linux/skbuff.h:1265 [inline]
[<00000000143579a6>] sock_omalloc+0xaa/0x190 net/core/sock.c:2596
[<00000000be626478>] msg_zerocopy_alloc net/core/skbuff.c:1294 [inline]
[<00000000be626478>] msg_zerocopy_realloc+0x1ce/0x7f0 net/core/skbuff.c:1370
[<00000000cbfc9870>] __ip_append_data+0x2adf/0x3b30 net/ipv4/ip_output.c:1037
[<0000000089869146>] ip_make_skb+0x26c/0x2e0 net/ipv4/ip_output.c:1652
[<00000000098015c2>] udp_sendmsg+0x1bac/0x2390 net/ipv4/udp.c:1253
[<0000000045e0e95e>] inet_sendmsg+0x10a/0x150 net/ipv4/af_inet.c:819
[<000000008d31bfde>] sock_sendmsg_nosec net/socket.c:714 [inline]
[<000000008d31bfde>] sock_sendmsg+0x141/0x190 net/socket.c:734
[<0000000021e21aa4>] __sys_sendto+0x243/0x360 net/socket.c:2117
[<00000000ac0af00c>] __do_sys_sendto net/socket.c:2129 [inline]
[<00000000ac0af00c>] __se_sys_sendto net/socket.c:2125 [inline]
[<00000000ac0af00c>] __x64_sys_sendto+0xe1/0x1c0 net/socket.c:2125
[<0000000066999e0e>] do_syscall_x64 arch/x86/entry/common.c:50 [inline]
[<0000000066999e0e>] do_syscall_64+0x38/0x90 arch/x86/entry/common.c:80
[<0000000017f238c1>] entry_SYSCALL_64_after_hwframe+0x63/0xcd
Fixes: f214f915e7 ("tcp: enable MSG_ZEROCOPY")
Fixes: b5947e5d1e ("udp: msg_zerocopy")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d325c34d9e ]
After failing to verify configuration, it returns directly without
releasing link, which may cause memory leak.
Paolo Abeni thinks that the whole code of this driver is quite
"suboptimal" and looks unmainatained since at least ~15y, so he
suggests that we could simply remove the whole driver, please
take it into consideration.
Simon Horman suggests that the fix label should be set to
"Linux-2.6.12-rc2" considering that the problem has existed
since the driver was introduced and the commit above doesn't
seem to exist in net/net-next.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Gan Gecen <gangecen@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d913d32cc2 ]
Brad Spencer provided a detailed report [0] that when calling getsockopt()
for AF_NETLINK, some SOL_NETLINK options set only 1 byte even though such
options require at least sizeof(int) as length.
The options return a flag value that fits into 1 byte, but such behaviour
confuses users who do not initialise the variable before calling
getsockopt() and do not strictly check the returned value as char.
Currently, netlink_getsockopt() uses put_user() to copy data to optlen and
optval, but put_user() casts the data based on the pointer, char *optval.
As a result, only 1 byte is set to optval.
To avoid this behaviour, we need to use copy_to_user() or cast optval for
put_user().
Note that this changes the behaviour on big-endian systems, but we document
that the size of optval is int in the man page.
$ man 7 netlink
...
Socket options
To set or get a netlink socket option, call getsockopt(2) to read
or setsockopt(2) to write the option with the option level argument
set to SOL_NETLINK. Unless otherwise noted, optval is a pointer to
an int.
Fixes: 9a4595bc7e ("[NETLINK]: Add set/getsockopt options to support more than 32 groups")
Fixes: be0c22a46c ("netlink: add NETLINK_BROADCAST_ERROR socket option")
Fixes: 38938bfe34 ("netlink: add NETLINK_NO_ENOBUFS socket flag")
Fixes: 0a6a3a23ea ("netlink: add NETLINK_CAP_ACK socket option")
Fixes: 2d4bc93368 ("netlink: extended ACK reporting")
Fixes: 89d35528d1 ("netlink: Add new socket option to enable strict checking on dumps")
Reported-by: Brad Spencer <bspencer@blackberry.com>
Link: https://lore.kernel.org/netdev/ZD7VkNWFfp22kTDt@datsun.rim.net/
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Link: https://lore.kernel.org/r/20230421185255.94606-1-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db2bf510bd ]
This reverts commit 1e9ac114c4.
This patch introduces a possible null-ptr-def problem. Revert it. And the
fixed bug by this patch have resolved by commit 73f7b171b7 ("Bluetooth:
btsdio: fix use after free bug in btsdio_remove due to race condition").
Fixes: 1e9ac114c4 ("Bluetooth: btsdio: fix use after free bug in btsdio_remove due to unfinished work")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99e5acae19 ]
Like commit ea30388bae ("ipv6: Fix an uninit variable access bug in
__ip6_make_skb()"). icmphdr does not in skb linear region under the
scenario of SOCK_RAW socket. Access icmp_hdr(skb)->type directly will
trigger the uninit variable access bug.
Use a local variable icmp_type to carry the correct value in different
scenarios.
Fixes: 96793b4825 ("[IPV4]: Add ICMPMsgStats MIB (RFC 4293)")
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2cc8a008d6 ]
Function tcf_exts_init_ex() sets exts->miss_cookie_node ptr only
when use_action_miss is true so it assumes in other case that
the field is set to NULL by the caller. If not then the field
contains garbage and subsequent tcf_exts_destroy() call results
in a crash.
Ensure that the field .miss_cookie_node pointer is NULL when
use_action_miss parameter is false to avoid this potential scenario.
Fixes: 80cd22c35c ("net/sched: cls_api: Support hardware miss to tc action")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230420183634.1139391-1-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7041101ff6 ]
if sch_fq is configured with "initial quantum" having values greater than
INT_MAX, the first assignment of "credit" does signed integer overflow to
a very negative value.
In this situation, the syzkaller script provided by Cristoph triggers the
CPU soft-lockup warning even with few sockets. It's not an infinite loop,
but "credit" wasn't probably meant to be minus 2Gb for each new flow.
Capping "initial quantum" to INT_MAX proved to fix the issue.
v2: validation of "initial quantum" is done in fq_policy, instead of open
coding in fq_change() _ suggested by Jakub Kicinski
Reported-by: Christoph Paasch <cpaasch@apple.com>
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/377
Fixes: afe4fd0624 ("pkt_sched: fq: Fair Queue packet scheduler")
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Link: https://lore.kernel.org/r/7b3a3c7e36d03068707a021760a194a8eb5ad41a.1682002300.git.dcaratti@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a32e98506 ]
The ->cleanup callback needs to be removed, this doesn't work anymore as
the transaction mutex is already released in the ->abort function.
Just do it after a successful validation pass, this either happens
from commit or abort phases where transaction mutex is held.
Fixes: f102d66b33 ("netfilter: nf_tables: use dedicated mutex to guard transactions")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit acf1c3d68e ]
Florian and Eduard reported hard dead lock:
[ 58.433327] _raw_spin_lock_irqsave+0x40/0x50
[ 58.433334] btf_put+0x43/0x90
[ 58.433338] bpf_find_btf_id+0x157/0x240
[ 58.433353] btf_parse_fields+0x921/0x11c0
This happens since btf->refcount can be 1 at the time of btf_put() and
btf_put() will call btf_free_id() which will try to grab btf_idr_lock
and will dead lock.
Avoid the issue by doing btf_put() without locking.
Fixes: 3d78417b60 ("bpf: Add bpf_btf_find_by_name_kind() helper.")
Fixes: 1e89106da2 ("bpf: Add bpf_core_add_cands() and wire it into bpf_core_apply_relo_insn().")
Reported-by: Florian Westphal <fw@strlen.de>
Reported-by: Eduard Zingerman <eddyz87@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/bpf/20230421014901.70908-1-alexei.starovoitov@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35226750f7 ]
The system hang because of dsa_tag_8021q_port_setup()->
stmmac_vlan_rx_add_vid().
I found in stmmac_drv_probe() that cailing pm_runtime_put()
disabled the clock.
First, when the kernel is compiled with CONFIG_PM=y,The stmmac's
resume/suspend is active.
Secondly,stmmac as DSA master,the dsa_tag_8021q_port_setup() function
will callback stmmac_vlan_rx_add_vid when DSA dirver starts. However,
The system is hanged for the stmmac_vlan_rx_add_vid() accesses its
registers after stmmac's clock is closed.
I would suggest adding the pm_runtime_resume_and_get() to the
stmmac_vlan_rx_add_vid().This guarantees that resuming clock output
while in use.
Fixes: b3dcb31277 ("net: stmmac: correct clocks enabled in stmmac_vlan_rx_kill_vid()")
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Yan Wang <rk.code@outlook.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b540decd0 ]
On failing to create promisc flow steering table, the pointer is
returned with an error. Nullify it so unloading the driver won't try to
destroy a non existing table.
Failing to create promisc table may happen over BF devices when the ARM
side is going through a firmware tear down. The host side start a
reload flow. While the driver unloads, it tries to remove the promisc
table. Remove WARN in this state as it is a valid error flow.
Fixes: 1c46d7409f ("net/mlx5e: Optimize promiscuous mode")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dfad99750c ]
Use the same timeout for sync reset flow and health recovery flow, since
the former involves driver's recovery from firmware reset, which is
similar to health recovery. Otherwise, in some cases, such as a firmware
upgrade on the DPU, the firmware pre-init bit may not be ready within
current timeout and the driver will abort loading back after reset.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Fixes: 37ca95e62e ("net/mlx5: Increase FW pre-init timeout for health recovery")
Reviewed-by: Maher Sanalla <msanalla@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21608a2cf3 ]
This reverts commit 5977ac3910.
Revert this patch as we need the "recovery" arg back in mlx5_load_one()
function. This arg will be used in the next patch for using recovery
timeout during sync reset flow.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Maher Sanalla <msanalla@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Stable-dep-of: dfad99750c ("net/mlx5: Use recovery timeout on sync reset flow")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a6b069cc6 ]
On representor init rx error flow the flow steering pointer is being
released so mlx5e_attach_netdev() doesn't have a valid fs pointer
in its error flow. Make sure the pointer is nullified when released
and add a check in mlx5e_fs_cleanup() to verify fs is not null
as representor cleanup callback would be called anyway.
Fixes: af8bbf7300 ("net/mlx5e: Convert mlx5e_flow_steering member of mlx5e_priv to pointer")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4fbef0f8ea ]
The cited commit causes a regression. Tunnel device is not released
after tc update skb if skb needs to be freed. The following error
message will be printed:
unregister_netdevice: waiting for vxlan1 to become free. Usage count = 11
Fix it by releasing tunnel device if skb needs to be freed.
Fixes: 93a1ab2c54 ("net/mlx5: Refactor tc miss handling to a single function")
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c81893025 ]
Source port rewrite (forward to ovs internal port or statck device) isn't
supported in the rule of split action. So there is no indirect table in
split rule. The cited commit destroyes indirect table in split rule. The
indirect table for other rules will be destroyed wrongly. It will cause
traffic loss.
Fix it by removing the destroy function in split rule. And also remove
the destroy function in error flow.
Fixes: 10742efc20 ("net/mlx5e: VF tunnel TX traffic offloading")
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd745f4c0a ]
Currently when creating per vport table, create flags are hardcoded.
Devlink encap mode is set based on user input and HW capability.
Create per vport table based on devlink encap mode.
Fixes: c796bb7cd2 ("net/mlx5: E-switch, Generalize per vport table API")
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e85d3d5587 ]
ethtool uses `ETHTOOL_GRXRINGS` to compute how many queues are supported
by RSS. The driver should return the smaller of either:
- The maximum number of RSS queues the device supports, OR
- The number of RX queues configured
Prior to this change, running `ethtool -X $iface default` fails if the
number of queues configured is larger than the number supported by RSS,
even though changing the queue count correctly resets the flowhash to
use all supported queues.
Other drivers (for example, i40e) will succeed but the flow hash will
reset to support the maximum number of queues supported by RSS, even if
that amount is smaller than the configured amount.
Prior to this change:
$ sudo ethtool -L eth1 combined 20
$ sudo ethtool -x eth1
RX flow hash indirection table for eth1 with 20 RX ring(s):
0: 0 1 2 3 4 5 6 7
8: 8 9 10 11 12 13 14 15
16: 0 1 2 3 4 5 6 7
24: 8 9 10 11 12 13 14 15
32: 0 1 2 3 4 5 6 7
...
You can see that the flowhash was correctly set to use the maximum
number of queues supported by the driver (16).
However, asking the NIC to reset to "default" fails:
$ sudo ethtool -X eth1 default
Cannot set RX flow hash configuration: Invalid argument
After this change, the flowhash can be reset to default which will use
all of the available RSS queues (16) or the configured queue count,
whichever is smaller.
Starting with eth1 which has 10 queues and a flowhash distributing to
all 10 queues:
$ sudo ethtool -x eth1
RX flow hash indirection table for eth1 with 10 RX ring(s):
0: 0 1 2 3 4 5 6 7
8: 8 9 0 1 2 3 4 5
16: 6 7 8 9 0 1 2 3
...
Increasing the queue count to 48 resets the flowhash to distribute to 16
queues, as it did before this patch:
$ sudo ethtool -L eth1 combined 48
$ sudo ethtool -x eth1
RX flow hash indirection table for eth1 with 16 RX ring(s):
0: 0 1 2 3 4 5 6 7
8: 8 9 10 11 12 13 14 15
16: 0 1 2 3 4 5 6 7
...
Due to the other bugfix in this series, the flowhash can be set to use
queues 0-5:
$ sudo ethtool -X eth1 equal 5
$ sudo ethtool -x eth1
RX flow hash indirection table for eth1 with 16 RX ring(s):
0: 0 1 2 3 4 0 1 2
8: 3 4 0 1 2 3 4 0
16: 1 2 3 4 0 1 2 3
...
Due to this bugfix, the flowhash can be reset to default and use 16
queues:
$ sudo ethtool -X eth1 default
$ sudo ethtool -x eth1
RX flow hash indirection table for eth1 with 16 RX ring(s):
0: 0 1 2 3 4 5 6 7
8: 8 9 10 11 12 13 14 15
16: 0 1 2 3 4 5 6 7
...
Fixes: 91cd94bfe4 ("ixgbe: add basic support for setting and getting nfc controls")
Signed-off-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f3ed1293f ]
ixgbe currently returns `EINVAL` whenever the flowhash it set by ethtool
because the ethtool code in the kernel passes a non-zero value for hfunc
that ixgbe should allow.
When ethtool is called with `ETHTOOL_SRXFHINDIR`,
`ethtool_set_rxfh_indir` will call ixgbe's set_rxfh function
with `ETH_RSS_HASH_NO_CHANGE`. This value should be accepted.
When ethtool is called with `ETHTOOL_SRSSH`, `ethtool_set_rxfh` will
call ixgbe's set_rxfh function with `rxfh.hfunc`, which appears to be
hardcoded in ixgbe to always be `ETH_RSS_HASH_TOP`. This value should
also be accepted.
Before this patch:
$ sudo ethtool -L eth1 combined 10
$ sudo ethtool -X eth1 default
Cannot set RX flow hash configuration: Invalid argument
After this patch:
$ sudo ethtool -L eth1 combined 10
$ sudo ethtool -X eth1 default
$ sudo ethtool -x eth1
RX flow hash indirection table for eth1 with 10 RX ring(s):
0: 0 1 2 3 4 5 6 7
8: 8 9 0 1 2 3 4 5
16: 6 7 8 9 0 1 2 3
24: 4 5 6 7 8 9 0 1
...
Fixes: 1c7cf0784e ("ixgbe: support for ethtool set_rxfh")
Signed-off-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73db1b8f2b ]
(struct nf_conn)->timeout is an interval before the conntrack
confirmed. After confirmed, it becomes a timestamp.
It is observed that timeout of an unconfirmed conntrack:
- Set by calling ctnetlink_change_timeout(). As a result,
`nfct_time_stamp` was wrongly added to `ct->timeout` twice.
- Get by calling ctnetlink_dump_timeout(). As a result,
`nfct_time_stamp` was wrongly subtracted.
Call Trace:
<TASK>
dump_stack_lvl
ctnetlink_dump_timeout
__ctnetlink_glue_build
ctnetlink_glue_build
__nfqnl_enqueue_packet
nf_queue
nf_hook_slow
ip_mc_output
? __pfx_ip_finish_output
ip_send_skb
? __pfx_dst_output
udp_send_skb
udp_sendmsg
? __pfx_ip_generic_getfrag
sock_sendmsg
Separate the 2 cases in:
- Setting `ct->timeout` in __nf_ct_set_timeout().
- Getting `ct->timeout` in ctnetlink_dump_timeout().
Pablo appends:
Update ctnetlink to set up the timeout _after_ the IPS_CONFIRMED flag is
set on, otherwise conntrack creation via ctnetlink breaks.
Note that the problem described in this patch occurs since the
introduction of the nfnetlink_queue conntrack support, select a
sufficiently old Fixes: tag for -stable kernel to pick up this fix.
Fixes: a4b4766c3c ("netfilter: nfnetlink_queue: rename related to nfqueue attaching conntrack info")
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b522caded ]
The hardware SDO has issue to fill txd for the moment, so fallback to
driver filling method.
Fixes: 98686cd216 (wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices)
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d2892e050 ]
The vif->bss_conf.mcast_rate should be applied to multicast data frame
only.
Fixes: 182071cdd5 ("mt76: connac: move connac2_mac_write_txwi in mt76_connac module")
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d78c46423 ]
If the chip reset worker is triggered during the remove process, the chip
DMA may not be properly pushed back to the idle state. This can lead to
corruption of the DMA flow due to the chip reset. Therefore, it is
necessary to stop the chip reset before the DMA is finalized.
To avoid resetting the chip after the reset worker is cancelled, use
__mt7921_mcu_drv_pmctrl() instead of mt7921_mcu_drv_pmctrl(). It is safe to
ignore the pm mutex because the pm worker and wake worker have already been
cancelled.
Fixes: 033ae79b38 ("mt76: mt7921: refactor init.c to be bus independent")
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Co-developed-by: Wang Zhao <wang.zhao@mediatek.com>
Signed-off-by: Wang Zhao <wang.zhao@mediatek.com>
Signed-off-by: Quan Zhou <quan.zhou@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87714bf6ed ]
The hardware team has advised the driver that it is necessary to first put
WFDMA into an idle state before resetting the WFDMA. Otherwise, the WFDMA
may enter an unknown state where it cannot be polled with the right state
successfully. To ensure that the DMA can work properly while a stressful
cold reboot test was being made, we have reordered the programming sequence
in the driver based on the hardware team's guidance.
The patch would modify the WFDMA disabling flow from
"DMA reset -> disabling DMASHDL -> disabling WFDMA -> polling and waiting
until DMA idle" to "disabling WFDMA -> polling and waiting for DMA idle ->
disabling DMASHDL -> DMA reset.
Where he polling and waiting until WFDMA is idle is coordinated with the
operation of disabling WFDMA. Even while WFDMA is being disabled, it can
still handle Tx/Rx requests. The additional polling allows sufficient time
for WFDMA to process the last T/Rx request. When the idle state of WFDMA is
reached, it is a reliable indication that DMASHDL is also idle to ensure it
is safe to disable it and perform the DMA reset.
Fixes: 0a1059d0f0 ("mt76: mt7921: move mt7921_dma_reset in dma.c")
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Co-developed-by: Wang Zhao <wang.zhao@mediatek.com>
Signed-off-by: Wang Zhao <wang.zhao@mediatek.com>
Signed-off-by: Quan Zhou <quan.zhou@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c47cdebba ]
`mt7921u_dma_init` can only return zero or negative number according to its
definition. When it returns non-zero number, there exists an error and this
function should handle this error rather than return directly.
Fixes: 0d2afe09fa ("mt76: mt7921: add mt7921u driver")
Signed-off-by: Jiefeng Li <jiefeng_li@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23792cedaf ]
mt76 scan command only support 64 channels currently. If the
channel count is larger than 64(for 2+5+6GHz), some channels will
not be scanned. Hence change the scan type to full channel scan
in case of the command cannot include proper list for chip.
Fixes: 399090ef96 ("mt76: mt76_connac: move hw_scan and sched_scan routine in mt76_connac_mcu module")
Reported-by: Ben Greear <greearb@candelatech.com>
Tested-by: Isaac Konikoff <konikofi@candelatech.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c397fc1e63 ]
In system warm reboot scene, due to the polling timeout(now 1000us)
is too short to wait dma idle in time, it may make driver probe fail
with error code -ETIMEDOUT. Meanwhile, we also found the dma may take
around 70ms to enter idle state. Change the polling idle timeout to
100ms to avoid the probabilistic probe fail.
Tested pass with 5000 times warm reboot on x86 platform.
[4.477496] pci 0000:01:00.0: attach allowed to drvr mt7921e [internal device]
[4.478306] mt7921e 0000:01:00.0: ASIC revision: 79610010
[4.480063] mt7921e: probe of 0000:01:00.0 failed with error -110
Fixes: 0a1059d0f0 ("mt76: mt7921: move mt7921_dma_reset in dma.c")
Signed-off-by: Quan Zhou <quan.zhou@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5af1481a8 ]
FIF_* flags from mac80211 is not ABI. mt7921 should not pass it into mcu
directly. Remap FIF_* to driver defined flags as mcu command input.
Fixes: c222f77fd4 ("wifi: mt76: mt7921: fix rx filter incorrect by drv/fw inconsistent")
Signed-off-by: Neil Chen <yn.chen@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b14ce24a0 ]
Fix the tail and data pointers. The rxd->len in mt7996_mcu_rxd does not
include the length of general rxd. It only includes the length of
firmware event rxd. Use skb->length to get the correct length.
Fixes: 98686cd216 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c97df11df ]
If kernel do not enable CONFIG_HWMON, it may cause thermal
initialization to be done with temperature value 0 and then can not
transmit. This commit fixes it by setting trigger/restore temperature
before checking CONFIG_HWMON.
Fixes: 7d12b38ab6 ("wifi: mt76: mt7915: call mt7915_mcu_set_thermal_throttling() only after init_work")
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90fb69212c ]
On MT7986 the WiFi driver currently does not get automatically loaded,
requiring manual modprobing because the device tree compatibles are not
exported into metadata.
Add the missing MODULE_DEVICE_TABLE macro to fix this.
Fixes: 99ad32a4ca ("mt76: mt7915: add support for MT7986")
Signed-off-by: Lorenz Brun <lorenz@brun.one>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9270270d62 ]
mt7921 just stop some workers and clean up chip status before reboot.
In stress test, there are working activities still running at the period
of .shutdown callback and that would cause some hosts cannot recover
DMA after reboot. To avoid the floating state in reboot, we use
mt7921_pci_remove() to fully deinit all resources.
Fixes: f23a0cea8b ("wifi: mt76: mt7921e: add pci .shutdown() support")
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fcc51acfeb ]
Should not use AND operator to check vif type NL80211_IFTYPE_MONITOR, and
that will cause we go into sniffer command for both STA and MONITOR
mode. However, the sniffer command would set channel properly (with some
extra options), the STA mode still works even if using the wrong
command.
Fix vif type check to make sure we using the right command to update
channel.
Fixes: 914189af23 ("wifi: mt76: mt7921: fix channel switch fail in monitor mode")
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd159398a2 ]
When invalidating buffers under the partial tail page,
jbd2_journal_invalidate_folio() returns -EBUSY if the buffer is part of
the committing transaction as we cannot safely modify buffer state.
However if the buffer is already invalidated (due to previous
invalidation attempts from ext4_wait_for_tail_page_commit()), there's
nothing to do and there's no point in returning -EBUSY. This fixes
occasional warnings from ext4_journalled_invalidate_folio() triggered by
generic/051 fstest when blocksize < pagesize.
Fixes: 53e872681f ("ext4: fix deadlock in journal_unmap_buffer()")
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20230329154950.19720-1-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26208a7cff ]
raid10_sync_request() will add 'r10bio->remaining' for both rdev and
replacement rdev. However, if the read io fails, recovery_request_write()
returns without issuing the write io, in this case, end_sync_request()
is only called once and 'remaining' is leaked, cause an io hang.
Fix the problem by decreasing 'remaining' according to if 'bio' and
'repl_bio' is valid.
Fixes: 24afd80d99 ("md/raid10: handle recovery of replacement devices.")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230310073855.1337560-5-yukuai1@huaweicloud.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72c215ed87 ]
commit fe630de009 ("md/raid10: avoid deadlock on recovery.") allowed
normal io and sync io to exist at the same time. Task hung will occur as
below:
T1 T2 T3 T4
raid10d
handle_read_error
allow_barrier
conf->nr_pending--
-> 0
//submit sync io
raid10_sync_request
raise_barrier
->will not be blocked
...
//submit to drivers
raid10_read_request
wait_barrier
conf->nr_pending++
-> 1
//retry read fail
raid10_end_read_request
reschedule_retry
add to retry_list
conf->nr_queued++
-> 1
//sync io fail
end_sync_read
__end_sync_read
reschedule_retry
add to retry_list
conf->nr_queued++
-> 2
...
handle_read_error
get form retry_list
conf->nr_queued--
freeze_array
wait nr_pending == nr_queued+1
->1 ->2
//task hung
retry read and sync io will be added to retry_list(nr_queued->2) if they
fails. raid10d() called handle_read_error() and hung in freeze_array().
nr_queued will not decrease because raid10d is blocked, nr_pending will
not increase because conf->barrier is not released.
Fix it by moving allow_barrier() after raid10_read_request().
raise_barrier() will wait for nr_waiting to become 0. Therefore, sync io
and regular io will not be issued at the same time.
Also remove the check of nr_queued in stop_waiting_barrier. It can be 0
but don't need to be blocking. Remove the check for MD_RECOVERY_RUNNING as
the check is redundent.
Fixes: fe630de009 ("md/raid10: avoid deadlock on recovery.")
Signed-off-by: Li Nan <linan122@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230222041000.3341651-2-linan666@huaweicloud.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 935fc6fa64 ]
In __replace_atomic_write_block(), we missed to check return value
of inc_valid_block_count(), for extreme testcase that f2fs image is
run out of space, it may cause inconsistent status in between SIT
table and total valid block count.
Cc: Daeho Jeong <daehojeong@google.com>
Fixes: 3db1de0e58 ("f2fs: change the current atomic write way")
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de6d014a09 ]
Currently, perf_event sample period in perf_event_stackmap is set too low
that the test fails randomly. Fix this by using the max sample frequency,
from read_perf_max_sample_freq().
Move read_perf_max_sample_freq() to testing_helpers.c. Replace the CHECK()
with if-printf, as CHECK is not available in testing_helpers.c.
Fixes: 1da4864c2b ("selftests/bpf: Add callchain_stackid")
Signed-off-by: Song Liu <song@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20230412210423.900851-2-song@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f86a6ff6f ]
fcloop_fcp_op() could be called from flush request's ->end_io(flush_end_io) in
which the spinlock of fq->mq_flush_lock is grabbed with irq saved/disabled.
So fcloop_fcp_op() can't call spin_unlock_irq(&tfcp_req->reqlock) simply
which enables irq unconditionally.
Fixes the warning by switching to spin_lock_irqsave()/spin_unlock_irqrestore()
Fixes: c38dbbfab1 ("nvme-fcloop: fix inconsistent lock state warnings")
Reported-by: Yi Zhang <yi.zhang@redhat.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6622b76fe9 ]
Mixing AER Event Type and Event Info has masking clashes. Just print the
event type, but also include the event info of the AER result in the
trace.
Fixes: 09bd1ff4b1 ("nvme-core: add async event trace helper")
Reported-by: Nate Thornton <nate.thornton@samsung.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Minwoo Im <minwoo.im@samsung.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5a6ab0950 ]
For an identify command with cns set to NVME_ID_CNS_CS_CTRL, the NVMe
2.0 specification states that:
If the I/O Command Set specified by the CSI field does not have an
Identify Controller data structure, then the controller shall return
a zero filled data structure. If the host requests a data structure for
an I/O Command Set that the controller does not support, the controller
shall abort the command with a status code of Invalid Field in Command.
However, the current implementation of this identify command in
nvmet_execute_identify() only handles the ZNS command set, returning an
error for the NVM command set, which is not compliant with the
specifications as we do support this command set.
Fix this by:
1) Renaming nvmet_execute_identify_cns_cs_ctrl() to
nvmet_execute_identify_ctrl_zns() to continue handling the
ZNS command set as is.
2) Introduce a nvmet_execute_identify_ctrl_ns() helper to handle the
NVM command set, returning a zero filled nvme_id_ctrl_nvm data
structure.
3) Modify nvmet_execute_identify() to call these helpers based on
the csi specified, returning an error for unsupported command sets.
Fixes: aaf2e048af ("nvmet: add ZBD over ZNS backend support")
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Tested-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97416f67d5 ]
The identify command with cns set to NVME_ID_CNS_NS_ACTIVE_LIST does
not depend on the command set. The execution of this command should
thus not look at the csi field specified in the command. Simplify
nvmet_execute_identify() to directly call
nvmet_execute_identify_nslist() without the csi switch-case.
Fixes: ab5d0b38c0 ("nvmet: add Command Set Identifier support")
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Tested-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62904b3b33 ]
The identify command with cns set to NVME_ID_CNS_CTRL does not depend on
the command set. The execution of this command should thus not look at
the csi specified in the command. Simplify nvmet_execute_identify() to
directly call nvmet_execute_identify_ctrl() without the csi switch-case.
Fixes: ab5d0b38c0 ("nvmet: add Command Set Identifier support")
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Tested-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c098aa001 ]
The identify command with cns set to NVME_ID_CNS_NS does not directly
depend on the command set. The NVMe specifications is rather confusing
here as it appears that this command only applies to the NVM command
set. However, footnote 8 of Figure 273 in the NVMe 2.0 base
specifications clearly state that this command applies to NVM command
sets that support logical blocks, that is, NVM and ZNS. Both the NVM and
ZNS command set specifications also list this identify as mandatory.
The command handling should thus not look at the csi field since it is
defined as unused for this command. Given that we do not support the
KV command set, simply remove the csi switch-case for that command
handling and call directly nvmet_execute_identify_ns() in
nvmet_execute_identify().
Fixes: ab5d0b38c0 ("nvmet: add Command Set Identifier support")
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Tested-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab76e7206b ]
Nvme specifications state that:
If the I/O Command Set associated with the namespace identified by the
NSID field does not support the Identify Namespace data structure
specified by the CSI field, the controller shall abort the command with
a status code of Invalid Field in Command.
In other words, if nvmet_execute_identify_cns_cs_ns() is called for a
target with a block device that is not zoned, we should not return any
data and set the status to NVME_SC_INVALID_FIELD.
While at it, it is also better to revalidate the ns block devie *before*
checking if the block device is zoned, to ensure that
nvmet_execute_identify_cns_cs_ns() operates against updated device
characteristics.
Fixes: aaf2e048af ("nvmet: add ZBD over ZNS backend support")
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 756a7f9087 ]
While initializing spectral, the magic value is getting written to the
invalid memory address leading to random boot-up crash. This occurs
due to the incorrect index increment in ath11k_dbring_fill_magic_value
function. Fix it by replacing the existing logic with memset32 to ensure
there is no invalid memory access.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1
Fixes: d3d358efc5 ("ath11k: add spectral/CFR buffer validation support")
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230321052900.16895-1-quic_ppranees@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db21973263 ]
The usual devm_regulator_get() call already handles "optional"
regulators by returning a valid dummy and printing a warning
that the dummy regulator should be described properly. This
code open coded the same behaviour, but masked any errors that
are not -EPROBE_DEFER and is quite noisy.
This change effectively unmasks and propagates regulators errors
not involving -ENODEV, downgrades the error print to warning level
if no regulator is specified and captures the probe defer message
for /sys/kernel/debug/devices_deferred.
Fixes: 2e12f53663 ("net: stmmac: dwmac-rk: Use standard devicetree property for phy regulator")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea449f7fa0 ]
The clock requesting code is quite repetitive. Fix this by requesting
the clocks via devm_clk_bulk_get_optional. The optional variant has been
used, since this is effectively what the old code did. The exact clocks
required depend on the platform and configuration. As a side effect
this change adds correct -EPROBE_DEFER handling.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 7ad269ea1a ("GMAC: add driver for Rockchip RK3288 SoCs integrated GMAC")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91a0c0c141 ]
When if_type equals zero and pci_resource_start(pdev, PCI_64BIT_BAR4)
returns false, drbl_regs_memmap_p is not remapped. This passes a NULL
pointer to iounmap(), which can trigger a WARN() on certain arches.
When if_type equals six and pci_resource_start(pdev, PCI_64BIT_BAR4)
returns true, drbl_regs_memmap_p may has been remapped and
ctrl_regs_memmap_p is not remapped. This is a resource leak and passes a
NULL pointer to iounmap().
To fix these issues, we need to add null checks before iounmap(), and
change some goto labels.
Fixes: 1351e69fc6 ("scsi: lpfc: Add push-to-adapter support to sli4")
Signed-off-by: Shuchang Li <lishuchang@hust.edu.cn>
Link: https://lore.kernel.org/r/20230404072133.1022-1-lishuchang@hust.edu.cn
Reviewed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5cdb422c83 ]
xfstest generic/019 reports a bug:
kernel BUG at mm/filemap.c:1619!
RIP: 0010:folio_end_writeback+0x8a/0x90
Call Trace:
end_page_writeback+0x1c/0x60
f2fs_write_end_io+0x199/0x420
bio_endio+0x104/0x180
submit_bio_noacct+0xa5/0x510
submit_bio+0x48/0x80
f2fs_submit_write_bio+0x35/0x300
f2fs_submit_merged_ipu_write+0x2a0/0x2b0
f2fs_write_single_data_page+0x838/0x8b0
f2fs_write_cache_pages+0x379/0xa30
f2fs_write_data_pages+0x30c/0x340
do_writepages+0xd8/0x1b0
__writeback_single_inode+0x44/0x370
writeback_sb_inodes+0x233/0x4d0
__writeback_inodes_wb+0x56/0xf0
wb_writeback+0x1dd/0x2d0
wb_workfn+0x367/0x4a0
process_one_work+0x21d/0x430
worker_thread+0x4e/0x3c0
kthread+0x103/0x130
ret_from_fork+0x2c/0x50
The root cause is: after cp_error is set, f2fs_submit_merged_ipu_write()
in f2fs_write_single_data_page() tries to flush IPU bio in cache, however
f2fs_submit_merged_ipu_write() missed to check validity of @bio parameter,
result in submitting random cached bio which belong to other IO context,
then it will cause use-after-free issue, fix it by adding additional
validity check.
Fixes: 0b20fcec86 ("f2fs: cache global IPU bio")
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d769ccaf95 ]
Make sure unaligned descriptors that straddle the end of the UMEM are
considered invalid. Currently, descriptor validation is broken for
zero-copy mode which only checks descriptors at page granularity.
For example, descriptors in zero-copy mode that overrun the end of the
UMEM but not a page boundary are (incorrectly) considered valid. The
UMEM boundary check needs to happen before the page boundary and
contiguity checks in xp_desc_crosses_non_contig_pg(). Do this check in
xp_unaligned_validate_desc() instead like xp_check_unaligned() already
does.
Fixes: 2b43470add ("xsk: Introduce AF_XDP buffer allocation API")
Signed-off-by: Kal Conley <kal.conley@dectris.com>
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Link: https://lore.kernel.org/r/20230405235920.7305-2-kal.conley@dectris.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 686cd976b6 ]
When jent initialisation fails for any reason other than ENOENT,
the entire drbg fails to initialise, even when we're not in FIPS
mode. This is wrong because we can still use the kernel RNG when
we're not in FIPS mode.
Change it so that it only fails when we are in FIPS mode.
Fixes: 57225e6797 ("crypto: drbg - Use callback API for random readiness")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reviewed-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 67cf52cdb6 ]
When dumping the control flow graphs for programs using the 16-byte long
load instruction, we need to skip the second part of this instruction
when looking for the next instruction to process. Otherwise, we end up
printing "BUG_ld_00" from the kernel disassembler in the CFG.
Fixes: efcef17a6d ("tools: bpftool: generate .dot graph from CFG information")
Signed-off-by: Quentin Monnet <quentin@isovalent.com>
Link: https://lore.kernel.org/r/20230405132120.59886-3-quentin@isovalent.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5af607a861 ]
In some cases the loopback latency might be large enough, causing
the assertion on invocations to be run before ingress prog getting
executed. The assertion would fail and the test would flake.
This can be reliably reproduced by arbitrarily increasing the
loopback latency (thanks to [1]):
tc qdisc add dev lo root handle 1: htb default 12
tc class add dev lo parent 1:1 classid 1:12 htb rate 20kbps ceil 20kbps
tc qdisc add dev lo parent 1:12 netem delay 100ms
Fix this by waiting on the receive end, instead of instantly
returning to the assert. The call to read() will wait for the
default SO_RCVTIMEO timeout of 3 seconds provided by
start_server().
[1] https://gist.github.com/kstevens715/4598301
Reported-by: Martin KaFai Lau <martin.lau@linux.dev>
Link: https://lore.kernel.org/bpf/9c5c8b7e-1d89-a3af-5400-14fde81f4429@linux.dev/
Fixes: 3573f38401 ("selftests/bpf: Test CGROUP_STORAGE behavior on shared egress + ingress")
Acked-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: YiFei Zhu <zhuyifei@google.com>
Link: https://lore.kernel.org/r/20230405193354.1956209-1-zhuyifei@google.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68e7322142 ]
Fix flaky STATS_RX_DROPPED test. The receiver calls getsockopt after
receiving the last (valid) packet which is not the final packet sent in
the test (valid and invalid packets are sent in alternating fashion with
the final packet being invalid). Since the last packet may or may not
have been dropped already, both outcomes must be allowed.
This issue could also be fixed by making sure the last packet sent is
valid. This alternative is left as an exercise to the reader (or the
benevolent maintainers of this file).
This problem was quite visible on certain setups. On one machine this
failure was observed 50% of the time.
Also, remove a redundant assignment of pkt_stream->nb_pkts. This field
is already initialized by __pkt_stream_alloc.
Fixes: 27e934bec3 ("selftests: xsk: make stat tests not spin on getsockopt")
Signed-off-by: Kal Conley <kal.conley@dectris.com>
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Link: https://lore.kernel.org/r/20230403120400.31018-1-kal.conley@dectris.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2b50f1726 ]
This change fixes flakiness in the BIDIRECTIONAL test:
# [is_pkt_valid] expected length [60], got length [90]
not ok 1 FAIL: SKB BUSY-POLL BIDIRECTIONAL
When IPv6 is enabled, the interface will periodically send MLDv1 and
MLDv2 packets. These packets can cause the BIDIRECTIONAL test to fail
since it uses VETH0 for RX.
For other tests, this was not a problem since they only receive on VETH1
and IPv6 was already disabled on VETH0.
Fixes: a89052572e ("selftests/bpf: Xsk selftests framework")
Signed-off-by: Kal Conley <kal.conley@dectris.com>
Link: https://lore.kernel.org/r/20230405082905.6303-1-kal.conley@dectris.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 054fbf7ff8 ]
The arguments passed to the trace events are of type unsigned int,
however the signature of the events used __le32 parameters.
I may be missing the point here, but sparse flagged this and it
does seem incorrect to me.
net/qrtr/ns.c: note: in included file (through include/trace/trace_events.h, include/trace/define_trace.h, include/trace/events/qrtr.h):
./include/trace/events/qrtr.h:11:1: warning: cast to restricted __le32
./include/trace/events/qrtr.h:11:1: warning: restricted __le32 degrades to integer
./include/trace/events/qrtr.h:11:1: warning: restricted __le32 degrades to integer
... (a lot more similar warnings)
net/qrtr/ns.c:115:47: expected restricted __le32 [usertype] service
net/qrtr/ns.c:115:47: got unsigned int service
net/qrtr/ns.c:115:61: warning: incorrect type in argument 2 (different base types)
... (a lot more similar warnings)
Fixes: dfddb54043 ("net: qrtr: Add tracepoint support")
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230402-qrtr-trace-types-v1-1-92ad55008dd3@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6a6a5a976 ]
bpf_obj_drop_impl has a void return type. In check_kfunc_call, the "else
if" which sets insn_aux->kptr_struct_meta for bpf_obj_drop_impl is
surrounded by a larger if statement which checks btf_type_is_ptr. As a
result:
* The bpf_obj_drop_impl-specific code will never execute
* The btf_struct_meta input to bpf_obj_drop is always NULL
* __bpf_obj_drop_impl will always see a NULL btf_record when called
from BPF program, and won't call bpf_obj_free_fields
* program-allocated kptrs which have fields that should be cleaned up
by bpf_obj_free_fields may instead leak resources
This patch adds a btf_type_is_void branch to the larger if and moves
special handling for bpf_obj_drop_impl there, fixing the issue.
Fixes: ac9f06050a ("bpf: Introduce bpf_obj_drop")
Cc: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Dave Marchevsky <davemarchevsky@fb.com>
Link: https://lore.kernel.org/r/20230403200027.2271029-1-davemarchevsky@fb.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07236eab7a ]
Factor out logic to fetch basic kfunc metadata based on struct bpf_insn.
This is not exactly short or trivial code to just copy/paste and this
information is sometimes necessary in other parts of the verifier logic.
Subsequent patches will rely on this to determine if an instruction is
a kfunc call to iterator next method.
No functional changes intended, including that verbose() warning
behavior when kfunc is not allowed for a particular program type.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20230308184121.1165081-2-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Stable-dep-of: f6a6a5a976 ("bpf: Fix struct_meta lookup for bpf_obj_free_fields kfunc call")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb544224da ]
If an NCQ error occurs when the IPTT is valid and slot->abort flag is set
in completion path, sas_task_abort() will be called to abort only one NCQ
command now, and the host would be set to SHOST_RECOVERY state. But this
may not kick-off EH Immediately until other outstanding QCs timeouts. As a
result, the host may remain in the SHOST_RECOVERY state for up to 30
seconds, such as follows:
[7972317.645234] hisi_sas_v3_hw 0000:74:04.0: erroneous completion iptt=3264 task=00000000466116b8 dev id=2 sas_addr=0x5000000000000502 CQ hdr: 0x1883 0x20cc0 0x40000 0x20420000 Error info: 0x0 0x0 0x200000 0x0
[7972341.508264] sas: Enter sas_scsi_recover_host busy: 32 failed: 32
[7972341.984731] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 32 tries: 1
All NCQ commands that are in the queue should be aborted when an NCQ error
occurs in this scenario.
Fixes: 05d91b557a ("scsi: hisi_sas: Directly trigger SCSI error handling for completion errors")
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1679283265-115066-3-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8832023efd ]
The SA2UL Crypto driver provides support for couple of
DES3 algos "cbc(des3_ede)" and "ecb(des3_ede)", and enabling
the crypto selftest throws the following errors (as seen on
K3 J721E SoCs):
saul-crypto 4e00000.crypto: Error allocating fallback algo cbc(des3_ede)
alg: skcipher: failed to allocate transform for cbc-des3-sa2ul: -2
saul-crypto 4e00000.crypto: Error allocating fallback algo ecb(des3_ede)
alg: skcipher: failed to allocate transform for ecb-des3-sa2ul: -2
Fix this by selecting CRYPTO_DES which was missed while
adding base driver support.
Fixes: 7694b6ca64 ("crypto: sa2ul - Add crypto driver")
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c19fb86a8 ]
According to the comment at the end of the 'for' loop just a few lines
below, it looks needed to clear 'desc'.
So it should also be cleared for the first iteration.
Move the memset() to the beginning of the loop to be safe.
Fixes: 281922a1d4 ("crypto: caam - add support for SEC v5.x RNG4")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Gaurav Jain <gaurav.jain@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit babedcbac1 ]
BUG_ON() will be triggered when writing files concurrently,
because the same page is writtenback multiple times.
1597 void folio_end_writeback(struct folio *folio)
1598 {
......
1618 if (!__folio_end_writeback(folio))
1619 BUG();
......
1625 }
kernel BUG at mm/filemap.c:1619!
Call Trace:
<TASK>
f2fs_write_end_io+0x1a0/0x370
blk_update_request+0x6c/0x410
blk_mq_end_request+0x15/0x130
blk_complete_reqs+0x3c/0x50
__do_softirq+0xb8/0x29b
? sort_range+0x20/0x20
run_ksoftirqd+0x19/0x20
smpboot_thread_fn+0x10b/0x1d0
kthread+0xde/0x110
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x22/0x30
</TASK>
Below is the concurrency scenario:
[Process A] [Process B] [Process C]
f2fs_write_raw_pages()
- redirty_page_for_writepage()
- unlock page()
f2fs_do_write_data_page()
- lock_page()
- clear_page_dirty_for_io()
- set_page_writeback() [1st writeback]
.....
- unlock page()
generic_perform_write()
- f2fs_write_begin()
- wait_for_stable_page()
- f2fs_write_end()
- set_page_dirty()
- lock_page()
- f2fs_do_write_data_page()
- set_page_writeback() [2st writeback]
This problem was introduced by the previous commit 7377e85396 ("f2fs:
compress: fix potential deadlock of compress file"). All pagelocks were
released in f2fs_write_raw_pages(), but whether the page was
in the writeback state was ignored in the subsequent writing process.
Let's fix it by waiting for the page to writeback before writing.
Cc: Christoph Hellwig <hch@lst.de>
Fixes: 4c8ff7095b ("f2fs: support data compression")
Fixes: 7377e85396 ("f2fs: compress: fix potential deadlock of compress file")
Signed-off-by: Qi Han <hanqi@vivo.com>
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b37ed21e3 ]
If we manage the zone capacity per zone type, it'll break the GC assumption.
And, the current logic complains valid block count mismatch.
Let's apply zone capacity to all zone type, if specified.
Fixes: de881df977 ("f2fs: support zone capacity less than zone size")
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c17caf0ba3 ]
When f2fs skipped a gc round during victim migration, there was a bug which
would skip all upcoming gc rounds unconditionally because skipped_gc_rwsem
was not initialized. It fixes the bug by correctly initializing the
skipped_gc_rwsem inside the gc loop.
Fixes: 6f8d445506 ("f2fs: avoid fi->i_gc_rwsem[WRITE] lock in f2fs_gc")
Signed-off-by: Yonggil Song <yonggil.song@samsung.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d61157414d ]
Fix an uninitialized return code if we never found a qfe slot. It would be
a bug if we ever got into this situation, but it's good to return something
tracable.
Fixes: acb3f35f92 ("sunhme: forward the error code from pci_enable_device()")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc79da306e ]
Fix a bug added in commit f36199355c ("scsi: target: iscsi: Fix cmd abort
fabric stop race").
If CMD_T_TAS is set on the se_cmd we must call iscsit_free_cmd() to do the
last put on the cmd and free it, because the connection is down and we will
not up sending the response and doing the put from the normal I/O
path.
Add a check for CMD_T_TAS in iscsit_release_commands_from_conn() so we now
detect this case and run iscsit_free_cmd().
Fixes: f36199355c ("scsi: target: iscsi: Fix cmd abort fabric stop race")
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20230319015620.96006-9-michael.christie@oracle.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 673db054d7 ]
This fixes a bug where an initiator thinks a LUN_RESET has cleaned up
running commands when it hasn't. The bug was added in commit 51ec502a32
("target: Delete tmr from list before processing").
The problem occurs when:
1. We have N I/O cmds running in the target layer spread over 2 sessions.
2. The initiator sends a LUN_RESET for each session.
3. session1's LUN_RESET loops over all the running commands from both
sessions and moves them to its local drain_task_list.
4. session2's LUN_RESET does not see the LUN_RESET from session1 because
the commit above has it remove itself. session2 also does not see any
commands since the other reset moved them off the state lists.
5. sessions2's LUN_RESET will then complete with a successful response.
6. sessions2's inititor believes the running commands on its session are
now cleaned up due to the successful response and cleans up the running
commands from its side. It then restarts them.
7. The commands do eventually complete on the backend and the target
starts to return aborted task statuses for them. The initiator will
either throw a invalid ITT error or might accidentally lookup a new
task if the ITT has been reallocated already.
Fix the bug by reverting the patch, and serialize the execution of
LUN_RESETs and Preempt and Aborts.
Also prevent us from waiting on LUN_RESETs in core_tmr_drain_tmr_list,
because it turns out the original patch fixed a bug that was not
mentioned. For LUN_RESET1 core_tmr_drain_tmr_list can see a second
LUN_RESET and wait on it. Then the second reset will run
core_tmr_drain_tmr_list and see the first reset and wait on it resulting in
a deadlock.
Fixes: 51ec502a32 ("target: Delete tmr from list before processing")
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20230319015620.96006-8-michael.christie@oracle.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 395cee83d0 ]
This fixes a bug added in commit f36199355c ("scsi: target: iscsi: Fix
cmd abort fabric stop race").
If we have multiple sessions to the same se_device we can hit a race where
a LUN_RESET on one session cleans up the se_cmds from under another
session which is being closed. This results in the closing session freeing
its conn/session structs while they are still in use.
The bug is:
1. Session1 has IO se_cmd1.
2. Session2 can also have se_cmds for I/O and optionally TMRs for ABORTS
but then gets a LUN_RESET.
3. The LUN_RESET on session2 sees the se_cmds on session1 and during the
drain stages marks them all with CMD_T_ABORTED.
4. session1 is now closed so iscsit_release_commands_from_conn() only sees
se_cmds with the CMD_T_ABORTED bit set and returns immediately even
though we have outstanding commands.
5. session1's connection and session are freed.
6. The backend request for se_cmd1 completes and it accesses the freed
connection/session.
This hooks the iscsit layer into the cmd counter code, so we can wait for
all outstanding se_cmds before freeing the connection.
Fixes: f36199355c ("scsi: target: iscsi: Fix cmd abort fabric stop race")
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20230319015620.96006-6-michael.christie@oracle.com
Reviewed-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4edba7e4a8 ]
iSCSI needs to allocate its cmd counter per connection for MCS support
where we need to stop and wait on commands running on a connection instead
of per session. This moves the cmd counter allocation to
target_setup_session() which is used by drivers that need the stop+wait
behavior per session.
xcopy doesn't need stop+wait at all, so we will be OK moving the cmd
counter allocation outside of transport_init_session().
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20230319015620.96006-3-michael.christie@oracle.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stable-dep-of: 395cee83d0 ("scsi: target: iscsit: Stop/wait on cmds during conn close")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit becd9be606 ]
iSCSI needs to wait on outstanding commands like how SRP and the FC/FCoE
drivers do. It can't use target_stop_session() because for MCS support we
can't stop the entire session during recovery because if other connections
are OK then we want to be able to continue to execute I/O on them.
Move the per session cmd counters to a new struct so iSCSI can allocate
them per connection. The xcopy code can also just not allocate in the
future since it doesn't need to track commands.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20230319015620.96006-2-michael.christie@oracle.com
Reviewed-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stable-dep-of: 395cee83d0 ("scsi: target: iscsit: Stop/wait on cmds during conn close")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7be14c1c90 ]
Xu reports that after commit 3f50f132d8 ("bpf: Verifier, do explicit ALU32
bounds tracking"), the following BPF program is rejected by the verifier:
0: (61) r2 = *(u32 *)(r1 +0) ; R2_w=pkt(off=0,r=0,imm=0)
1: (61) r3 = *(u32 *)(r1 +4) ; R3_w=pkt_end(off=0,imm=0)
2: (bf) r1 = r2
3: (07) r1 += 1
4: (2d) if r1 > r3 goto pc+8
5: (71) r1 = *(u8 *)(r2 +0) ; R1_w=scalar(umax=255,var_off=(0x0; 0xff))
6: (18) r0 = 0x7fffffffffffff10
8: (0f) r1 += r0 ; R1_w=scalar(umin=0x7fffffffffffff10,umax=0x800000000000000f)
9: (18) r0 = 0x8000000000000000
11: (07) r0 += 1
12: (ad) if r0 < r1 goto pc-2
13: (b7) r0 = 0
14: (95) exit
And the verifier log says:
func#0 @0
0: R1=ctx(off=0,imm=0) R10=fp0
0: (61) r2 = *(u32 *)(r1 +0) ; R1=ctx(off=0,imm=0) R2_w=pkt(off=0,r=0,imm=0)
1: (61) r3 = *(u32 *)(r1 +4) ; R1=ctx(off=0,imm=0) R3_w=pkt_end(off=0,imm=0)
2: (bf) r1 = r2 ; R1_w=pkt(off=0,r=0,imm=0) R2_w=pkt(off=0,r=0,imm=0)
3: (07) r1 += 1 ; R1_w=pkt(off=1,r=0,imm=0)
4: (2d) if r1 > r3 goto pc+8 ; R1_w=pkt(off=1,r=1,imm=0) R3_w=pkt_end(off=0,imm=0)
5: (71) r1 = *(u8 *)(r2 +0) ; R1_w=scalar(umax=255,var_off=(0x0; 0xff)) R2_w=pkt(off=0,r=1,imm=0)
6: (18) r0 = 0x7fffffffffffff10 ; R0_w=9223372036854775568
8: (0f) r1 += r0 ; R0_w=9223372036854775568 R1_w=scalar(umin=9223372036854775568,umax=9223372036854775823,s32_min=-240,s32_max=15)
9: (18) r0 = 0x8000000000000000 ; R0_w=-9223372036854775808
11: (07) r0 += 1 ; R0_w=-9223372036854775807
12: (ad) if r0 < r1 goto pc-2 ; R0_w=-9223372036854775807 R1_w=scalar(umin=9223372036854775568,umax=9223372036854775809)
13: (b7) r0 = 0 ; R0_w=0
14: (95) exit
from 12 to 11: R0_w=-9223372036854775807 R1_w=scalar(umin=9223372036854775810,umax=9223372036854775823,var_off=(0x8000000000000000; 0xffffffff)) R2_w=pkt(off=0,r=1,imm=0) R3_w=pkt_end(off=0,imm=0) R10=fp0
11: (07) r0 += 1 ; R0_w=-9223372036854775806
12: (ad) if r0 < r1 goto pc-2 ; R0_w=-9223372036854775806 R1_w=scalar(umin=9223372036854775810,umax=9223372036854775810,var_off=(0x8000000000000000; 0xffffffff))
13: safe
[...]
from 12 to 11: R0_w=-9223372036854775795 R1=scalar(umin=9223372036854775822,umax=9223372036854775823,var_off=(0x8000000000000000; 0xffffffff)) R2=pkt(off=0,r=1,imm=0) R3=pkt_end(off=0,imm=0) R10=fp0
11: (07) r0 += 1 ; R0_w=-9223372036854775794
12: (ad) if r0 < r1 goto pc-2 ; R0_w=-9223372036854775794 R1=scalar(umin=9223372036854775822,umax=9223372036854775822,var_off=(0x8000000000000000; 0xffffffff))
13: safe
from 12 to 11: R0_w=-9223372036854775794 R1=scalar(umin=9223372036854775823,umax=9223372036854775823,var_off=(0x8000000000000000; 0xffffffff)) R2=pkt(off=0,r=1,imm=0) R3=pkt_end(off=0,imm=0) R10=fp0
11: (07) r0 += 1 ; R0_w=-9223372036854775793
12: (ad) if r0 < r1 goto pc-2 ; R0_w=-9223372036854775793 R1=scalar(umin=9223372036854775823,umax=9223372036854775823,var_off=(0x8000000000000000; 0xffffffff))
13: safe
from 12 to 11: R0_w=-9223372036854775793 R1=scalar(umin=9223372036854775824,umax=9223372036854775823,var_off=(0x8000000000000000; 0xffffffff)) R2=pkt(off=0,r=1,imm=0) R3=pkt_end(off=0,imm=0) R10=fp0
11: (07) r0 += 1 ; R0_w=-9223372036854775792
12: (ad) if r0 < r1 goto pc-2 ; R0_w=-9223372036854775792 R1=scalar(umin=9223372036854775824,umax=9223372036854775823,var_off=(0x8000000000000000; 0xffffffff))
13: safe
[...]
The 64bit umin=9223372036854775810 bound continuously bumps by +1 while
umax=9223372036854775823 stays as-is until the verifier complexity limit
is reached and the program gets finally rejected. During this simulation,
the umin also eventually surpasses umax. Looking at the first 'from 12
to 11' output line from the loop, R1 has the following state:
R1_w=scalar(umin=0x8000000000000002 (9223372036854775810),
umax=0x800000000000000f (9223372036854775823),
var_off=(0x8000000000000000;
0xffffffff))
The var_off has technically not an inconsistent state but it's very
imprecise and far off surpassing 64bit umax bounds whereas the expected
output with refined known bits in var_off should have been like:
R1_w=scalar(umin=0x8000000000000002 (9223372036854775810),
umax=0x800000000000000f (9223372036854775823),
var_off=(0x8000000000000000;
0xf))
In the above log, var_off stays as var_off=(0x8000000000000000; 0xffffffff)
and does not converge into a narrower mask where more bits become known,
eventually transforming R1 into a constant upon umin=9223372036854775823,
umax=9223372036854775823 case where the verifier would have terminated and
let the program pass.
The __reg_combine_64_into_32() marks the subregister unknown and propagates
64bit {s,u}min/{s,u}max bounds to their 32bit equivalents iff they are within
the 32bit universe. The question came up whether __reg_combine_64_into_32()
should special case the situation that when 64bit {s,u}min bounds have
the same value as 64bit {s,u}max bounds to then assign the latter as
well to the 32bit reg->{s,u}32_{min,max}_value. As can be seen from the
above example however, that is just /one/ special case and not a /generic/
solution given above example would still not be addressed this way and
remain at an imprecise var_off=(0x8000000000000000; 0xffffffff).
The improvement is needed in __reg_bound_offset() to refine var32_off with
the updated var64_off instead of the prior reg->var_off. The reg_bounds_sync()
code first refines information about the register's min/max bounds via
__update_reg_bounds() from the current var_off, then in __reg_deduce_bounds()
from sign bit and with the potentially learned bits from bounds it'll
update the var_off tnum in __reg_bound_offset(). For example, intersecting
with the old var_off might have improved bounds slightly, e.g. if umax
was 0x7f...f and var_off was (0; 0xf...fc), then new var_off will then
result in (0; 0x7f...fc). The intersected var64_off holds then the
universe which is a superset of var32_off. The point for the latter is
not to broaden, but to further refine known bits based on the intersection
of var_off with 32 bit bounds, so that we later construct the final var_off
from upper and lower 32 bits. The final __update_reg_bounds() can then
potentially still slightly refine bounds if more bits became known from the
new var_off.
After the improvement, we can see R1 converging successively:
func#0 @0
0: R1=ctx(off=0,imm=0) R10=fp0
0: (61) r2 = *(u32 *)(r1 +0) ; R1=ctx(off=0,imm=0) R2_w=pkt(off=0,r=0,imm=0)
1: (61) r3 = *(u32 *)(r1 +4) ; R1=ctx(off=0,imm=0) R3_w=pkt_end(off=0,imm=0)
2: (bf) r1 = r2 ; R1_w=pkt(off=0,r=0,imm=0) R2_w=pkt(off=0,r=0,imm=0)
3: (07) r1 += 1 ; R1_w=pkt(off=1,r=0,imm=0)
4: (2d) if r1 > r3 goto pc+8 ; R1_w=pkt(off=1,r=1,imm=0) R3_w=pkt_end(off=0,imm=0)
5: (71) r1 = *(u8 *)(r2 +0) ; R1_w=scalar(umax=255,var_off=(0x0; 0xff)) R2_w=pkt(off=0,r=1,imm=0)
6: (18) r0 = 0x7fffffffffffff10 ; R0_w=9223372036854775568
8: (0f) r1 += r0 ; R0_w=9223372036854775568 R1_w=scalar(umin=9223372036854775568,umax=9223372036854775823,s32_min=-240,s32_max=15)
9: (18) r0 = 0x8000000000000000 ; R0_w=-9223372036854775808
11: (07) r0 += 1 ; R0_w=-9223372036854775807
12: (ad) if r0 < r1 goto pc-2 ; R0_w=-9223372036854775807 R1_w=scalar(umin=9223372036854775568,umax=9223372036854775809)
13: (b7) r0 = 0 ; R0_w=0
14: (95) exit
from 12 to 11: R0_w=-9223372036854775807 R1_w=scalar(umin=9223372036854775810,umax=9223372036854775823,var_off=(0x8000000000000000; 0xf),s32_min=0,s32_max=15,u32_max=15) R2_w=pkt(off=0,r=1,imm=0) R3_w=pkt_end(off=0,imm=0) R10=fp0
11: (07) r0 += 1 ; R0_w=-9223372036854775806
12: (ad) if r0 < r1 goto pc-2 ; R0_w=-9223372036854775806 R1_w=-9223372036854775806
13: safe
from 12 to 11: R0_w=-9223372036854775806 R1_w=scalar(umin=9223372036854775811,umax=9223372036854775823,var_off=(0x8000000000000000; 0xf),s32_min=0,s32_max=15,u32_max=15) R2_w=pkt(off=0,r=1,imm=0) R3_w=pkt_end(off=0,imm=0) R10=fp0
11: (07) r0 += 1 ; R0_w=-9223372036854775805
12: (ad) if r0 < r1 goto pc-2 ; R0_w=-9223372036854775805 R1_w=-9223372036854775805
13: safe
[...]
from 12 to 11: R0_w=-9223372036854775798 R1=scalar(umin=9223372036854775819,umax=9223372036854775823,var_off=(0x8000000000000008; 0x7),s32_min=8,s32_max=15,u32_min=8,u32_max=15) R2=pkt(off=0,r=1,imm=0) R3=pkt_end(off=0,imm=0) R10=fp0
11: (07) r0 += 1 ; R0_w=-9223372036854775797
12: (ad) if r0 < r1 goto pc-2 ; R0_w=-9223372036854775797 R1=-9223372036854775797
13: safe
from 12 to 11: R0_w=-9223372036854775797 R1=scalar(umin=9223372036854775820,umax=9223372036854775823,var_off=(0x800000000000000c; 0x3),s32_min=12,s32_max=15,u32_min=12,u32_max=15) R2=pkt(off=0,r=1,imm=0) R3=pkt_end(off=0,imm=0) R10=fp0
11: (07) r0 += 1 ; R0_w=-9223372036854775796
12: (ad) if r0 < r1 goto pc-2 ; R0_w=-9223372036854775796 R1=-9223372036854775796
13: safe
from 12 to 11: R0_w=-9223372036854775796 R1=scalar(umin=9223372036854775821,umax=9223372036854775823,var_off=(0x800000000000000c; 0x3),s32_min=12,s32_max=15,u32_min=12,u32_max=15) R2=pkt(off=0,r=1,imm=0) R3=pkt_end(off=0,imm=0) R10=fp0
11: (07) r0 += 1 ; R0_w=-9223372036854775795
12: (ad) if r0 < r1 goto pc-2 ; R0_w=-9223372036854775795 R1=-9223372036854775795
13: safe
from 12 to 11: R0_w=-9223372036854775795 R1=scalar(umin=9223372036854775822,umax=9223372036854775823,var_off=(0x800000000000000e; 0x1),s32_min=14,s32_max=15,u32_min=14,u32_max=15) R2=pkt(off=0,r=1,imm=0) R3=pkt_end(off=0,imm=0) R10=fp0
11: (07) r0 += 1 ; R0_w=-9223372036854775794
12: (ad) if r0 < r1 goto pc-2 ; R0_w=-9223372036854775794 R1=-9223372036854775794
13: safe
from 12 to 11: R0_w=-9223372036854775794 R1=-9223372036854775793 R2=pkt(off=0,r=1,imm=0) R3=pkt_end(off=0,imm=0) R10=fp0
11: (07) r0 += 1 ; R0_w=-9223372036854775793
12: (ad) if r0 < r1 goto pc-2
last_idx 12 first_idx 12
parent didn't have regs=1 stack=0 marks: R0_rw=P-9223372036854775801 R1_r=scalar(umin=9223372036854775815,umax=9223372036854775823,var_off=(0x8000000000000000; 0xf),s32_min=0,s32_max=15,u32_max=15) R2=pkt(off=0,r=1,imm=0) R3=pkt_end(off=0,imm=0) R10=fp0
last_idx 11 first_idx 11
regs=1 stack=0 before 11: (07) r0 += 1
parent didn't have regs=1 stack=0 marks: R0_rw=P-9223372036854775805 R1_rw=scalar(umin=9223372036854775812,umax=9223372036854775823,var_off=(0x8000000000000000; 0xf),s32_min=0,s32_max=15,u32_max=15) R2_w=pkt(off=0,r=1,imm=0) R3_w=pkt_end(off=0,imm=0) R10=fp0
last_idx 12 first_idx 0
regs=1 stack=0 before 12: (ad) if r0 < r1 goto pc-2
regs=1 stack=0 before 11: (07) r0 += 1
regs=1 stack=0 before 12: (ad) if r0 < r1 goto pc-2
regs=1 stack=0 before 11: (07) r0 += 1
regs=1 stack=0 before 12: (ad) if r0 < r1 goto pc-2
regs=1 stack=0 before 11: (07) r0 += 1
regs=1 stack=0 before 9: (18) r0 = 0x8000000000000000
last_idx 12 first_idx 12
parent didn't have regs=2 stack=0 marks: R0_rw=P-9223372036854775801 R1_r=Pscalar(umin=9223372036854775815,umax=9223372036854775823,var_off=(0x8000000000000000; 0xf),s32_min=0,s32_max=15,u32_max=15) R2=pkt(off=0,r=1,imm=0) R3=pkt_end(off=0,imm=0) R10=fp0
last_idx 11 first_idx 11
regs=2 stack=0 before 11: (07) r0 += 1
parent didn't have regs=2 stack=0 marks: R0_rw=P-9223372036854775805 R1_rw=Pscalar(umin=9223372036854775812,umax=9223372036854775823,var_off=(0x8000000000000000; 0xf),s32_min=0,s32_max=15,u32_max=15) R2_w=pkt(off=0,r=1,imm=0) R3_w=pkt_end(off=0,imm=0) R10=fp0
last_idx 12 first_idx 0
regs=2 stack=0 before 12: (ad) if r0 < r1 goto pc-2
regs=2 stack=0 before 11: (07) r0 += 1
regs=2 stack=0 before 12: (ad) if r0 < r1 goto pc-2
regs=2 stack=0 before 11: (07) r0 += 1
regs=2 stack=0 before 12: (ad) if r0 < r1 goto pc-2
regs=2 stack=0 before 11: (07) r0 += 1
regs=2 stack=0 before 9: (18) r0 = 0x8000000000000000
regs=2 stack=0 before 8: (0f) r1 += r0
regs=3 stack=0 before 6: (18) r0 = 0x7fffffffffffff10
regs=2 stack=0 before 5: (71) r1 = *(u8 *)(r2 +0)
13: safe
from 4 to 13: safe
verification time 322 usec
stack depth 0
processed 56 insns (limit 1000000) max_states_per_insn 1 total_states 3 peak_states 3 mark_read 1
This also fixes up a test case along with this improvement where we match
on the verifier log. The updated log now has a refined var_off, too.
Fixes: 3f50f132d8 ("bpf: Verifier, do explicit ALU32 bounds tracking")
Reported-by: Xu Kuohai <xukuohai@huaweicloud.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20230314203424.4015351-2-xukuohai@huaweicloud.com
Link: https://lore.kernel.org/bpf/20230322213056.2470-1-daniel@iogearbox.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7ba4cc900 ]
This patch changes the return types of bpf_map_ops functions to long, where
previously int was returned. Using long allows for bpf programs to maintain
the sign bit in the absence of sign extension during situations where
inlined bpf helper funcs make calls to the bpf_map_ops funcs and a negative
error is returned.
The definitions of the helper funcs are generated from comments in the bpf
uapi header at `include/uapi/linux/bpf.h`. The return type of these
helpers was previously changed from int to long in commit bdb7b79b4c. For
any case where one of the map helpers call the bpf_map_ops funcs that are
still returning 32-bit int, a compiler might not include sign extension
instructions to properly convert the 32-bit negative value a 64-bit
negative value.
For example:
bpf assembly excerpt of an inlined helper calling a kernel function and
checking for a specific error:
; err = bpf_map_update_elem(&mymap, &key, &val, BPF_NOEXIST);
...
46: call 0xffffffffe103291c ; htab_map_update_elem
; if (err && err != -EEXIST) {
4b: cmp $0xffffffffffffffef,%rax ; cmp -EEXIST,%rax
kernel function assembly excerpt of return value from
`htab_map_update_elem` returning 32-bit int:
movl $0xffffffef, %r9d
...
movl %r9d, %eax
...results in the comparison:
cmp $0xffffffffffffffef, $0x00000000ffffffef
Fixes: bdb7b79b4c ("bpf: Switch most helper return values from 32-bit int to 64-bit long")
Tested-by: Eduard Zingerman <eddyz87@gmail.com>
Signed-off-by: JP Kobryn <inwardvessel@gmail.com>
Link: https://lore.kernel.org/r/20230322194754.185781-3-inwardvessel@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0e214d212 ]
Keep the conntrack reference until policy checks have been performed for
IPsec V6 NAT support, just like ipv4.
The reference needs to be dropped before a packet is
queued to avoid having the conntrack module unloadable.
Fixes: 58a317f106 ("netfilter: ipv6: add IPv6 NAT support")
Signed-off-by: Madhu Koriginja <madhu.koriginja@nxp.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a506d6ce1d ]
Unlike normal libbpf the light skeleton 'loader' program is doing
btf_find_by_name_kind() call at run-time to find ksym in the kernel and
populate its {btf_id, btf_obj_fd} pair in ld_imm64 insn. To avoid doing the
search multiple times for the same ksym it remembers the first patched ld_imm64
insn and copies {btf_id, btf_obj_fd} from it into subsequent ld_imm64 insn.
Fix a bug in copying logic, since it may incorrectly clear BPF_PSEUDO_BTF_ID flag.
Also replace always true if (btf_obj_fd >= 0) check with unconditional JMP_JA
to clarify the code.
Fixes: d995816b77 ("libbpf: Avoid reload of imm for weak, unresolved, repeating ksym")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20230319203014.55866-1-alexei.starovoitov@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd53c297aa ]
po->auxdata can be read while another thread
is changing its value, potentially raising KCSAN splat.
Convert it to PACKET_SOCK_AUXDATA flag.
Fixes: 8dc4194474 ("[PACKET]: Add optional checksum computation for recvmsg")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee5675ecdf ]
syzbot/KCAN reported that po->origdev can be read
while another thread is changing its value.
We can avoid this splat by converting this field
to an actual bit.
Following patches will convert remaining 1bit fields.
Fixes: 80feaacb8a ("[AF_PACKET]: Add option to return orig_dev to userspace.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b9d83ab8a7 ]
po->xmit can be set from setsockopt(PACKET_QDISC_BYPASS),
while read locklessly.
Use READ_ONCE()/WRITE_ONCE() to avoid potential load/store
tearing issues.
Fixes: d346a3fae3 ("packet: introduce PACKET_QDISC_BYPASS socket option")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 731b73dba3 ]
Setting timestamp filter was explicitly disabled on vlan devices in
containers because it might affect other processes on the host. But it's
absolutely legit in case when real device is in the same namespace.
Fixes: 873017af77 ("vlan: disable SIOCSHWTSTAMP in container")
Signed-off-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef63461caf ]
Phylink does not want the current state of the link when reading the
PCS link state - it wants the latched state. Don't double-read the
MII status register. Phylink will re-read as necessary to capture
transient link-down events as of dbae3388ea ("net: phylink: Force
retrigger in case of latched link-fail indicator").
The above referenced commit is a dependency for this change, and thus
this change should not be backported to any kernel that does not
contain the above referenced commit.
Fixes: fcb26bd2b6 ("net: phy: Add Synopsys DesignWare XPCS MDIO module")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 082cdc69a4 ]
For every BPF_ADD/SUB involving a pointer, adjust_ptr_min_max_vals()
ensures that the resulting pointer has a constant offset if
bypass_spec_v1 is false. This is ensured by calling sanitize_check_bounds()
which in turn calls check_stack_access_for_ptr_arithmetic(). There,
-EACCESS is returned if the register's offset is not constant, thereby
rejecting the program.
In summary, an unprivileged user must never be able to create stack
pointers with a variable offset. That is also the case, because a
respective check in check_stack_write() is missing. If they were able
to create a variable-offset pointer, users could still use it in a
stack-write operation to trigger unsafe speculative behavior [1].
Because unprivileged users must already be prevented from creating
variable-offset stack pointers, viable options are to either remove
this check (replacing it with a clarifying comment), or to turn it
into a "verifier BUG"-message, also adding a similar check in
check_stack_write() (for consistency, as a second-level defense).
This patch implements the first option to reduce verifier bloat.
This check was introduced by commit 01f810ace9 ("bpf: Allow
variable-offset stack access") which correctly notes that
"variable-offset reads and writes are disallowed (they were already
disallowed for the indirect access case) because the speculative
execution checking code doesn't support them". However, it does not
further discuss why the check in check_stack_read() is necessary.
The code which made this check obsolete was also introduced in this
commit.
I have compiled ~650 programs from the Linux selftests, Linux samples,
Cilium, and libbpf/examples projects and confirmed that none of these
trigger the check in check_stack_read() [2]. Instead, all of these
programs are, as expected, already rejected when constructing the
variable-offset pointers. Note that the check in
check_stack_access_for_ptr_arithmetic() also prints "off=%d" while the
code removed by this patch does not (the error removed does not appear
in the "verification_error" values). For reproducibility, the
repository linked includes the raw data and scripts used to create
the plot.
[1] https://arxiv.org/pdf/1807.03757.pdf
[2] 53dc19fcf4/data/plots/23-02-26_23-56_bpftool/bpftool/0004-errors.pdf
Fixes: 01f810ace9 ("bpf: Allow variable-offset stack access")
Signed-off-by: Luis Gerhorst <gerhorst@cs.fau.de>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20230315165358.23701-1-gerhorst@cs.fau.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77473d1a96 ]
The struct bpf_cpumask type uses the bpf_mem_cache_{alloc,free}() APIs
to allocate and free its cpumasks. The bpf_mem allocator may currently
immediately reuse some memory when its freed, without waiting for an RCU
read cycle to elapse. We want to be able to treat struct bpf_cpumask
objects as completely RCU safe.
This is necessary for two reasons:
1. bpf_cpumask_kptr_get() currently does an RCU-protected
refcnt_inc_not_zero(). This of course assumes that the underlying
memory is not reused, and is therefore unsafe in its current form.
2. We want to be able to get rid of bpf_cpumask_kptr_get() entirely, and
intead use the superior kptr RCU semantics now afforded by the
verifier.
This patch fixes (1), and enables (2), by making struct bpf_cpumask RCU
safe. A subsequent patch will update the verifier to allow struct
bpf_cpumask * pointers to be passed to KF_RCU kfuncs, and then a latter
patch will remove bpf_cpumask_kptr_get().
Fixes: 516f4d3397 ("bpf: Enable cpumasks to be queried and used as kptrs")
Signed-off-by: David Vernet <void@manifault.com>
Link: https://lore.kernel.org/r/20230316054028.88924-2-void@manifault.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a78ac33e3 ]
Currently, in ath11k_ahb_fw_resources_init(), iommu domain
mapping is done only for the chipsets having fixed firmware
memory. Also, for such chipsets, mapping is done only if it
does not have TrustZone support.
During deinitialization, only if TrustZone support is not there,
iommu is unmapped back. However, for non fixed firmware memory
chipsets, TrustZone support is not there and this makes the
condition check to true and it tries to unmap the memory which
was not mapped during initialization.
This leads to the following trace -
[ 83.198790] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000008
[ 83.259537] Modules linked in: ath11k_ahb ath11k qmi_helpers
.. snip ..
[ 83.280286] pstate: 20000005 (nzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 83.287228] pc : __iommu_unmap+0x30/0x140
[ 83.293907] lr : iommu_unmap+0x5c/0xa4
[ 83.298072] sp : ffff80000b3abad0
.. snip ..
[ 83.369175] Call trace:
[ 83.376282] __iommu_unmap+0x30/0x140
[ 83.378541] iommu_unmap+0x5c/0xa4
[ 83.382360] ath11k_ahb_fw_resource_deinit.part.12+0x2c/0xac [ath11k_ahb]
[ 83.385666] ath11k_ahb_free_resources+0x140/0x17c [ath11k_ahb]
[ 83.392521] ath11k_ahb_shutdown+0x34/0x40 [ath11k_ahb]
[ 83.398248] platform_shutdown+0x20/0x2c
[ 83.403455] device_shutdown+0x16c/0x1c4
[ 83.407621] kernel_restart_prepare+0x34/0x3c
[ 83.411529] kernel_restart+0x14/0x74
[ 83.415781] __do_sys_reboot+0x1c4/0x22c
[ 83.419427] __arm64_sys_reboot+0x1c/0x24
[ 83.423420] invoke_syscall+0x44/0xfc
[ 83.427326] el0_svc_common.constprop.3+0xac/0xe8
[ 83.430974] do_el0_svc+0xa0/0xa8
[ 83.435659] el0_svc+0x1c/0x44
[ 83.438957] el0t_64_sync_handler+0x60/0x144
[ 83.441910] el0t_64_sync+0x15c/0x160
[ 83.446343] Code: aa0103f4 f9400001 f90027a1 d2800001 (f94006a0)
[ 83.449903] ---[ end trace 0000000000000000 ]---
This can be reproduced by probing an AHB chipset which is not
having a fixed memory region. During reboot (or rmmod) trace
can be seen.
Fix this issue by adding a condition check on firmware fixed memory
hw_param as done in the counter initialization function.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Fixes: f9eec4947a ("ath11k: Add support for targets without trustzone")
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230309095308.24937-1-quic_adisi@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a02d83f994 ]
Currently, kernel would set MSG_CTRUNC flag if msg_control buffer
wasn't provided and SO_PASSCRED was set or if there was pending SCM_RIGHTS.
For some reason we have no corresponding check for SO_PASSSEC.
In the recvmsg(2) doc we have:
MSG_CTRUNC
indicates that some control data was discarded due to lack
of space in the buffer for ancillary data.
So, we need to set MSG_CTRUNC flag for all types of SCM.
This change can break applications those don't check MSG_CTRUNC flag.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Leon Romanovsky <leon@kernel.org>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Alexander Mikhalitsyn <aleksandr.mikhalitsyn@canonical.com>
v2:
- commit message was rewritten according to Eric's suggestion
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1bdc85550a ]
The sysfs `state` attribute is not protected against race conditions.
If multiple processes perform a device state transition on the same
device in parallel, unexpected behaviors might occur.
For transitioning the device state, adf_sysfs.c calls the functions
adf_dev_init(), adf_dev_start(), adf_dev_stop() and adf_dev_shutdown()
which are unprotected and interdependent on each other. To perform a
state transition, these functions needs to be called in a specific
order:
* device up: adf_dev_init() -> adf_dev_start()
* device down: adf_dev_stop() -> adf_dev_shutdown()
This change introduces the functions adf_dev_up() and adf_dev_down()
which wrap the state machine functions and protect them with a
per-device lock. These are then used in adf_sysfs.c instead of the
individual state transition functions.
Fixes: 5ee52118ac ("crypto: qat - expose device state through sysfs for 4xxx")
Signed-off-by: Shashank Gupta <shashank.gupta@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 52c2b005a3 ]
When doing state comparison, if old state has register that is not
marked as REG_LIVE_READ, then we just skip comparison, regardless what's
the state of corresponing register in current state. This is because not
REG_LIVE_READ register is irrelevant for further program execution and
correctness. All good here.
But when we get to precision propagation, after two states were declared
equivalent, we don't take into account old register's liveness, and thus
attempt to propagate precision for register in current state even if
that register in old state was not REG_LIVE_READ anymore. This is bad,
because register in current state could be anything at all and this
could cause -EFAULT due to internal logic bugs.
Fix by taking into account REG_LIVE_READ liveness mark to keep the logic
in state comparison in sync with precision propagation.
Fixes: a3ce685dd0 ("bpf: fix precision tracking")
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20230309224131.57449-1-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a686557631 ]
There is a report that fib_lookup test is flaky when running in parallel.
A symptom of slowness or delay. An example:
Testing IPv6 stale neigh
set_lookup_params:PASS:inet_pton(IPV6_IFACE_ADDR) 0 nsec
test_fib_lookup:PASS:bpf_prog_test_run_opts 0 nsec
test_fib_lookup:FAIL:fib_lookup_ret unexpected fib_lookup_ret: actual 0 != expected 7
test_fib_lookup:FAIL:dmac not match unexpected dmac not match: actual 1 != expected 0
dmac expected 11:11:11:11:11:11 actual 00:00:00:00:00:00
[ Note that the "fib_lookup_ret unexpected fib_lookup_ret actual 0 ..."
is reversed in terms of expected and actual value. Fixing in this
patch also. ]
One possibility is the testing stale neigh entry was marked dead by the
gc (in neigh_periodic_work). The default gc_stale_time sysctl is 60s.
This patch increases it to 15 mins.
It also:
- fixes the reversed arg (actual vs expected) in one of the
ASSERT_EQ test
- removes the nodad command arg when adding v4 neigh entry which
currently has a warning.
Fixes: 168de02335 ("selftests/bpf: Add bpf_fib_lookup test")
Reported-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20230309060244.3242491-1-martin.lau@linux.dev
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 12fabae03c ]
Commit 62622dab0a ("ima: return IMA digest value only when IMA_COLLECTED
flag is set") caused bpf_ima_inode_hash() to refuse to give non-fresh
digests. IMA test #3 assumed the old behavior, that bpf_ima_inode_hash()
still returned also non-fresh digests.
Correct the test by accepting both cases. If the samples returned are 1,
assume that the commit above is applied and that the returned digest is
fresh. If the samples returned are 2, assume that the commit above is not
applied, and check both the non-fresh and fresh digest.
Fixes: 62622dab0a ("ima: return IMA digest value only when IMA_COLLECTED flag is set")
Reported-by: David Vernet <void@manifault.com>
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Reviewed-by: Matt Bobrowski <mattbobrowski@google.com>
Link: https://lore.kernel.org/bpf/20230308103713.1681200-1-roberto.sassu@huaweicloud.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8ee37bde4 ]
Commit 04d58f1b26a4("libbpf: add API to get XDP/XSK supported features")
added feature_flags to struct bpf_xdp_query_opts. If a user uses
bpf_xdp_query_opts with feature_flags member, the bpf_xdp_query()
will check whether 'netdev' family exists or not in the kernel.
If it does not exist, the bpf_xdp_query() will return -ENOENT.
But 'netdev' family does not exist in old kernels as it is
introduced in the same patch set as Commit 04d58f1b26.
So old kernel with newer libbpf won't work properly with
bpf_xdp_query() api call.
To fix this issue, if the return value of
libbpf_netlink_resolve_genl_family_id() is -ENOENT, bpf_xdp_query()
will just return 0, skipping the rest of xdp feature query.
This preserves backward compatibility.
Fixes: 04d58f1b26 ("libbpf: add API to get XDP/XSK supported features")
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20230227224943.1153459-1-yhs@fb.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06943ae675 ]
The syscall register definitions for ARM in bpf_tracing.h doesn't define
the fifth parameter for the syscalls. Because of this some KPROBES based
selftests fail to compile for ARM architecture.
Define the fifth parameter that is passed in the R5 register (uregs[4]).
Fixes: 3a95c42d65 ("libbpf: Define arm syscall regs spec in bpf_tracing.h")
Signed-off-by: Puranjay Mohan <puranjay12@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20230223095346.10129-1-puranjay12@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c679bbd611 ]
RFC8259 ("The JavaScript Object Notation (JSON) Data Interchange
Format") only specifies \", \\, \/, \b, \f, \n, \r, and \r as valid
two-character escape sequences. This does not include \', which is not
required in JSON because it exclusively uses double quotes as string
separators.
Solidus (/) may be escaped, but does not have to. Only reverse
solidus (\), double quotes ("), and the control characters have to be
escaped. Therefore, with this fix, bpftool correctly supports all valid
two-character escape sequences (but still does not support characters
that require multi-character escape sequences).
Witout this fix, attempting to load a JSON file generated by bpftool
using Python 3.10.6's default json.load() may fail with the error
"Invalid \escape" if the file contains the invalid escaped single
quote (\').
Fixes: b66e907cfe ("tools: bpftool: copy JSON writer from iproute2 repository")
Signed-off-by: Luis Gerhorst <gerhorst@cs.fau.de>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Reviewed-by: Quentin Monnet <quentin@isovalent.com>
Link: https://lore.kernel.org/bpf/20230227150853.16863-1-gerhorst@cs.fau.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec52d77d07 ]
Using the BCM4339 firmware from linux-firmware (version "BCM4339/2 wl0:
Sep 5 2019 11:05:52 version 6.37.39.113 (r722271 CY)" from
cypress/cyfmac4339-sdio.bin) the RSSI respose is only 4 bytes, which
results in an error being logged.
It seems that older devices send only the RSSI field and neither SNR nor
noise is included. Handle this by accepting a 4 byte message and
reading only the RSSI from it.
Fixes: 7dd56ea45a ("brcmfmac: add support for CQM RSSI notifications")
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230124104248.2917465-1-john@metanate.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60b7d62ba8 ]
Fix sleep in atomic context warning detected by Smatch static checker
analyzer.
Following the locking pattern for peer_rhash_add lock tbl_mtx_lock mutex
always even if sta is not transitioning to another band.
This is peer_add function and a more secure locking should not cause
performance regression.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01208-QCAHKSWPL_SILICONZ-1
Fixes: d673cb6fe6 ("wifi: ath11k: fix peer addition/deletion error on sta band migration")
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230209222622.1751-1-ansuelsmth@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95c95251d0 ]
As of commit a1a2b7125e ("of/platform: Drop static setup of IRQ
resource from DT core"), we need to use platform_get_irq() instead of
platform_get_resource() to get our IRQs because
platform_get_resource() simply won't get them anymore.
This was already fixed in several other Atheros WiFi drivers,
apparently in response to Zeal Robot reports. An example of another
fix is commit 9503a1fc12 ("ath9k: Use platform_get_irq() to get the
interrupt"). ath5k seems to have been missed in this effort, though.
Fixes: a1a2b7125e ("of/platform: Drop static setup of IRQ resource from DT core")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230201084131.v2.2.Ic4f8542b0588d7eb4bc6e322d4af3d2064e84ff0@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f117276638 ]
As of commit a1a2b7125e ("of/platform: Drop static setup of IRQ
resource from DT core"), we need to use platform_get_irq() instead of
platform_get_resource() to get our IRQs because
platform_get_resource() simply won't get them anymore.
This was already fixed in several other Atheros WiFi drivers,
apparently in response to Zeal Robot reports. An example of another
fix is commit 9503a1fc12 ("ath9k: Use platform_get_irq() to get the
interrupt"). ath11k seems to have been missed in this effort, though.
Without this change, WiFi wasn't coming up on my Qualcomm sc7280-based
hardware. Specifically, "platform_get_resource(pdev, IORESOURCE_IRQ,
i)" was failing even for i=0.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Fixes: a1a2b7125e ("of/platform: Drop static setup of IRQ resource from DT core")
Fixes: 00402f49d2 ("ath11k: Add support for WCN6750 device")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Jun Yu <junyuu@chromium.org>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230201084131.v2.1.I69cf3d56c97098287fe3a70084ee515098390b70@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7654cc03eb ]
hif_dev->remain_skb is allocated and used exclusively in
ath9k_hif_usb_rx_stream(). It is implied that an allocated remain_skb is
processed and subsequently freed (in error paths) only during the next
call of ath9k_hif_usb_rx_stream().
So, if the urbs are deallocated between those two calls due to the device
deinitialization or suspend, it is possible that ath9k_hif_usb_rx_stream()
is not called next time and the allocated remain_skb is leaked. Our local
Syzkaller instance was able to trigger that.
remain_skb makes sense when receiving two consecutive urbs which are
logically linked together, i.e. a specific data field from the first skb
indicates a cached skb to be allocated, memcpy'd with some data and
subsequently processed in the next call to ath9k_hif_usb_rx_stream(). Urbs
deallocation supposedly makes that link irrelevant so we need to free the
cached skb in those cases.
Fix the leak by introducing a function to explicitly free remain_skb (if
it is not NULL) when the rx urbs have been deallocated. remain_skb is NULL
when it has not been allocated at all (hif_dev struct is kzalloced) or
when it has been processed in next call to ath9k_hif_usb_rx_stream().
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: fb9987d0f7 ("ath9k_htc: Support for AR9271 chipset.")
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230216192301.171225-1-pchelkin@ispras.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73b41dc51f ]
devm_clk_get() will return either an error or NULL, which the driver
handles, continuing to use the clock of reading the value of the
clock-frequency property.
However, the value of ov5670->xvclk is left as-is and the other clock
framework functions aren't capable of handling error values.
Use devm_clk_get_optional() to obtain NULL instead of -ENOENT.
Fixes: 8004c91e20 ("media: i2c: ov5670: Use common clock framework")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93822f5161 ]
The bit flags in pmbus_driver_info functionality for YM-2151E chip were
joined with a comma operator instead of a bitwise OR. This means that
the last constant PMBUS_HAVE_IIN was not OR-ed with the other
PM_BUS_HAVE_* constants for this page but it initialized the next element
of the func array (which was not accessed from anywhere because of the
number of pages).
However, there is no need for setting PMBUS_HAVE_IIN in the 5Vsb page
because this command does not seem to be paged. Obviously, the device
only has one IIN sensor, so it doesn't make sense to query it again from
the second page.
Fixes: 1734b4135a ("hwmon: Add driver for fsp-3y PSUs and PDUs")
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Tomáš Pecka <tomas.pecka@cesnet.cz>
Link: https://lore.kernel.org/r/20230420171939.212040-1-tomas.pecka@cesnet.cz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a68f9fa97 ]
As support for splitting transmission over several messages using
TX_DATA_CONT was introduced it does not immediately return the return
value of qcom_glink_tx().
The result is that in the intentless case (i.e. intent == NULL), the
code will continue to send all additional chunks. This is wasteful, and
it's possible that the send operation could incorrectly indicate
success, if the last chunk fits in the TX fifo.
Fix the condition.
Fixes: 8956927fae ("rpmsg: glink: Add TX_DATA_CONT command while sending")
Reviewed-by: Chris Lew <quic_clew@quicinc.com>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230418163018.785524-2-quic_bjorande@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44295af501 ]
cpufreq_verify_current_freq checks() if the frequency returned by
the hardware has a slight delta with the valid frequency value
last set and returns "policy->cur" if the delta is within "1 MHz".
In the comparison, "policy->cur" is in "kHz" but it's compared
against HZ_PER_MHZ. So, the comparison range becomes "1 GHz".
Fix this by comparing against KHZ_PER_MHZ instead of HZ_PER_MHZ.
Fixes: f55ae08c89 ("cpufreq: Avoid unnecessary frequency updates due to mismatch")
Signed-off-by: Sanjay Chandrashekara <sanjayc@nvidia.com>
[ sumit gupta: Commit message update ]
Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit faae443738 ]
Currently, acpi_device_remove_notify_handler() may return while the
notify handler being removed is still running which may allow the
module holding that handler to be torn down prematurely.
Address this issue by making acpi_device_remove_notify_handler() wait
for the handling of all the ACPI events in progress to complete before
returning.
Fixes: 5894b0c46e ("ACPI / scan: Move bus operations and notification routines to bus.c")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e9523a0d81 ]
With HIGHRES enabled tick_sched_timer() is programmed every jiffy to
expire the timer_list timers. This timer is programmed accurate in
respect to CLOCK_MONOTONIC so that 0 seconds and nanoseconds is the
first tick and the next one is 1000/CONFIG_HZ ms later. For HZ=250 it is
every 4 ms and so based on the current time the next tick can be
computed.
This accuracy broke since the commit mentioned below because the jiffy
based clocksource is initialized with higher accuracy in
read_persistent_wall_and_boot_offset(). This higher accuracy is
inherited during the setup in tick_setup_device(). The timer still fires
every 4ms with HZ=250 but timer is no longer aligned with
CLOCK_MONOTONIC with 0 as it origin but has an offset in the us/ns part
of the timestamp. The offset differs with every boot and makes it
impossible for user land to align with the tick.
Align the tick period with CLOCK_MONOTONIC ensuring that it is always a
multiple of 1000/CONFIG_HZ ms.
Fixes: 857baa87b6 ("sched/clock: Enable sched clock early")
Reported-by: Gusenleitner Klaus <gus@keba.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/20230406095735.0_14edn3@linutronix.de
Link: https://lore.kernel.org/r/20230418122639.ikgfvu3f@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63a759694e ]
Statically initialized objects are usually not initialized via the init()
function of the subsystem. They are special cased and the subsystem
provides a function to validate whether an object which is not yet tracked
by debugobjects is statically initialized. This means the object is started
to be tracked on first use, e.g. activation.
This works perfectly fine, unless there are two concurrent operations on
that object. Schspa decoded the problem:
T0 T1
debug_object_assert_init(addr)
lock_hash_bucket()
obj = lookup_object(addr);
if (!obj) {
unlock_hash_bucket();
- > preemption
lock_subsytem_object(addr);
activate_object(addr)
lock_hash_bucket();
obj = lookup_object(addr);
if (!obj) {
unlock_hash_bucket();
if (is_static_object(addr))
init_and_track(addr);
lock_hash_bucket();
obj = lookup_object(addr);
obj->state = ACTIVATED;
unlock_hash_bucket();
subsys function modifies content of addr,
so static object detection does
not longer work.
unlock_subsytem_object(addr);
if (is_static_object(addr)) <- Fails
debugobject emits a warning and invokes the fixup function which
reinitializes the already active object in the worst case.
This race exists forever, but was never observed until mod_timer() got a
debug_object_assert_init() added which is outside of the timer base lock
held section right at the beginning of the function to cover the lockless
early exit points too.
Rework the code so that the lookup, the static object check and the
tracking object association happens atomically under the hash bucket
lock. This prevents the issue completely as all callers are serialized on
the hash bucket lock and therefore cannot observe inconsistent state.
Fixes: 3ac7fe5a4a ("infrastructure to debug (dynamic) objects")
Reported-by: syzbot+5093ba19745994288b53@syzkaller.appspotmail.com
Debugged-by: Schspa Shi <schspa@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://syzkaller.appspot.com/bug?id=22c8a5938eab640d1c6bcc0e3dc7be519d878462
Link: https://lore.kernel.org/lkml/20230303161906.831686-1-schspa@gmail.com
Link: https://lore.kernel.org/r/87zg7dzgao.ffs@tglx
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e2a10b3801 ]
Need to disable decoder power when remove decoder hardware driver, adding
remove callback function in the definition of platform driver.
Fixes: c05bada35f ("media: mtk-vcodec: Add to support multi hardware decode")
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ad91e44e6 ]
When the "extra device ports" configuration was first added, the
additional mxp_device_port_connect_info registers were added around the
existing mxp_mesh_port_connect_info registers. What I missed about
CMN-700 is that it shuffled them around to remove this discontinuity.
As such, tweak the definitions and factor out a helper for reading these
registers so we can deal with this discrepancy easily, which does at
least allow nicely tidying up the callsites. With this we can then also
do the nice thing and skip accesses completely rather than relying on
RES0 behaviour where we know the extra registers aren't defined.
Fixes: 23760a0144 ("perf/arm-cmn: Add CMN-700 support")
Reported-by: Jing Zhang <renyu.zj@linux.alibaba.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/71d129241d4d7923cde72a0e5b4c8d2f6084525f.1681295193.git.robin.murphy@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af6c0bd59f ]
Currently only the first attempt to single-step has any effect. After
that all further stepping remains "stuck" at the same program counter
value.
Refer to the ARM Architecture Reference Manual (ARM DDI 0487E.a) D2.12,
PSTATE.SS=1 should be set at each step before transferring the PE to the
'Active-not-pending' state. The problem here is PSTATE.SS=1 is not set
since the second single-step.
After the first single-step, the PE transferes to the 'Inactive' state,
with PSTATE.SS=0 and MDSCR.SS=1, thus PSTATE.SS won't be set to 1 due to
kernel_active_single_step()=true. Then the PE transferes to the
'Active-pending' state when ERET and returns to the debugger by step
exception.
Before this patch:
==================
Entering kdb (current=0xffff3376039f0000, pid 1) on processor 0 due to Keyboard Entry
[0]kdb>
[0]kdb>
[0]kdb> bp write_sysrq_trigger
Instruction(i) BP #0 at 0xffffa45c13d09290 (write_sysrq_trigger)
is enabled addr at ffffa45c13d09290, hardtype=0 installed=0
[0]kdb> go
$ echo h > /proc/sysrq-trigger
Entering kdb (current=0xffff4f7e453f8000, pid 175) on processor 1 due to Breakpoint @ 0xffffad651a309290
[1]kdb> ss
Entering kdb (current=0xffff4f7e453f8000, pid 175) on processor 1 due to SS trap @ 0xffffad651a309294
[1]kdb> ss
Entering kdb (current=0xffff4f7e453f8000, pid 175) on processor 1 due to SS trap @ 0xffffad651a309294
[1]kdb>
After this patch:
=================
Entering kdb (current=0xffff6851c39f0000, pid 1) on processor 0 due to Keyboard Entry
[0]kdb> bp write_sysrq_trigger
Instruction(i) BP #0 at 0xffffc02d2dd09290 (write_sysrq_trigger)
is enabled addr at ffffc02d2dd09290, hardtype=0 installed=0
[0]kdb> go
$ echo h > /proc/sysrq-trigger
Entering kdb (current=0xffff6851c53c1840, pid 174) on processor 1 due to Breakpoint @ 0xffffc02d2dd09290
[1]kdb> ss
Entering kdb (current=0xffff6851c53c1840, pid 174) on processor 1 due to SS trap @ 0xffffc02d2dd09294
[1]kdb> ss
Entering kdb (current=0xffff6851c53c1840, pid 174) on processor 1 due to SS trap @ 0xffffc02d2dd09298
[1]kdb> ss
Entering kdb (current=0xffff6851c53c1840, pid 174) on processor 1 due to SS trap @ 0xffffc02d2dd0929c
[1]kdb>
Fixes: 44679a4f14 ("arm64: KGDB: Add step debugging support")
Co-developed-by: Wei Li <liwei391@huawei.com>
Signed-off-by: Wei Li <liwei391@huawei.com>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Tested-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20230202073148.657746-3-sumit.garg@linaro.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5af507bef9 ]
arch_dynirq_lower_bound() is invoked by the core interrupt code to
retrieve the lowest possible Linux interrupt number for dynamically
allocated interrupts like MSI.
The x86 implementation uses this to exclude the IO/APIC GSI space.
This works correctly as long as there is an IO/APIC registered, but
returns 0 if not. This has been observed in VMs where the BIOS does
not advertise an IO/APIC.
0 is an invalid interrupt number except for the legacy timer interrupt
on x86. The return value is unchecked in the core code, so it ends up
to allocate interrupt number 0 which is subsequently considered to be
invalid by the caller, e.g. the MSI allocation code.
The function has already a check for 0 in the case that an IO/APIC is
registered, as ioapic_dynirq_base is 0 in case of device tree setups.
Consolidate this and zero check for both ioapic_dynirq_base and gsi_top,
which is used in the case that no IO/APIC is registered.
Fixes: 3e5bedc2c2 ("x86/apic: Fix arch_dynirq_lower_bound() bug for DT enabled machines")
Signed-off-by: Saurabh Sengar <ssengar@linux.microsoft.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/1679988604-20308-1-git-send-email-ssengar@linux.microsoft.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4a413e56d ]
Smatch reports:
drivers/regulator/stm32-pwr.c:166 stm32_pwr_regulator_probe() warn:
'base' from of_iomap() not released on lines: 151,166.
In stm32_pwr_regulator_probe(), base is not released
when devm_kzalloc() fails to allocate memory or
devm_regulator_register() fails to register a new regulator device,
which may cause a leak.
To fix this issue, replace of_iomap() with
devm_platform_ioremap_resource(). devm_platform_ioremap_resource()
is a specialized function for platform devices.
It allows 'base' to be automatically released whether the probe
function succeeds or fails.
Besides, use IS_ERR(base) instead of !base
as the return value of devm_platform_ioremap_resource()
can either be a pointer to the remapped memory or
an ERR_PTR() encoded error code if the operation fails.
Fixes: dc62f951a6 ("regulator: stm32-pwr: Fix return value check in stm32_pwr_regulator_probe()")
Signed-off-by: YAN SHI <m202071378@hust.edu.cn>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/oe-kbuild-all/202304111750.o2643eJN-lkp@intel.com/
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/r/20230412033529.18890-1-m202071378@hust.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9d45ec74c ]
Commit 9593126dae ("media: venus: Add a handling of QC08C compressed
format") and commit cef92b14e6 ("media: venus: Add a handling of QC10C
compressed format") added support for the QC08C and QC10C compressed
formats respectively.
But these also caused a regression, because the new formats where added
at the beginning of the vdec_formats[] array and the vdec_inst_init()
function sets the default format output and capture using fixed indexes
of that array:
static void vdec_inst_init(struct venus_inst *inst)
{
...
inst->fmt_out = &vdec_formats[8];
inst->fmt_cap = &vdec_formats[0];
...
}
Since now V4L2_PIX_FMT_NV12 is not the first entry in the array anymore,
the default capture format is not set to that as it was done before.
Both commits changed the first index to keep inst->fmt_out default format
set to V4L2_PIX_FMT_H264, but did not update the latter to keep .fmt_out
default format set to V4L2_PIX_FMT_NV12.
Rather than updating the index to the current V4L2_PIX_FMT_NV12 position,
let's reorder the entries so that this format is the first entry again.
This would also make VIDIOC_ENUM_FMT report the V4L2_PIX_FMT_NV12 format
with an index 0 as it did before the QC08C and QC10C formats were added.
Fixes: 9593126dae ("media: venus: Add a handling of QC08C compressed format")
Fixes: cef92b14e6 ("media: venus: Add a handling of QC10C compressed format")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Stanimir Varbanov <stanimir.k.varbanov@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50248ad9f1 ]
The decoder driver should clear the last_buffer_dequeued flag of the
capture queue upon receiving V4L2_DEC_CMD_START.
The last_buffer_dequeued flag is set upon receiving EOS (which always
happens upon receiving V4L2_DEC_CMD_STOP).
Without this patch, after issuing the V4L2_DEC_CMD_STOP and
V4L2_DEC_CMD_START, the vb2_dqbuf() function will always fail, even if
the buffers are completed by the hardware.
Fixes: beac82904a ("media: venus: make decoder compliant with stateful codec API")
Signed-off-by: Michał Krawczyk <mk@semihalf.com>
Signed-off-by: Stanimir Varbanov <stanimir.k.varbanov@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c592f8ab1 ]
The driver was intended from the start to be a wake-up source for the
system, however due to the absence of a suitable call to
device_set_wakeup_capable(), the device_may_wakeup() call used to decide
whether to enable the GPIO interrupt as a wake-up source would never
happen. Lookup the DT standard "wakeup-source" property and call
device_init_wakeup() to ensure the device is flagged as being wakeup
capable.
Reported-by: Matthew Lear <matthew.lear@broadcom.com>
Fixes: fd0f6851eb ("[media] rc: Add support for GPIO based IR Receiver driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 52f1783ff4 ]
The adev->dm.dc pointer can be NULL and dereferenced in amdgpu_dm_fini()
without checking.
Add a NULL pointer check before calling dc_dmub_srv_destroy().
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 9a71c7d317 ("drm/amd/display: Register DMUB service with DC")
Signed-off-by: Igor Artemiev <Igor.A.Artemiev@mcst.ru>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2649c1a20e ]
hi846_init_controls doesn't clean the allocated ctrl_hdlr
in case there is a failure, which causes memleak. Add
v4l2_ctrl_handler_free to free the resource properly.
Fixes: e8c0882685 ("media: i2c: add driver for the SK Hynix Hi-846 8M pixel camera")
Signed-off-by: Wei Chen <harperchen1110@gmail.com>
Reviewed-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5276c9df9c ]
When an async notifier is unregistered, the async sub-devices in the
notifier's done list will disappear with the notifier. However this is
currently also done to the sub-notifiers that remain registered. Their
sub-devices only need to be unbound while the async sub-devices themselves
need to be returned to the sub-notifier's waiting list. Do this now.
Fixes: 2cab00bb07 ("media: v4l: async: Allow binding notifiers to sub-devices")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e82d3715f ]
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Stable-dep-of: c766c90faf ("media: rcar_fdp1: Fix refcount leak in probe and remove function")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 52d8caca3d ]
The vsp1 driver uses the vb2_is_streaming() function in its .buf_queue()
handler to check if the .start_streaming() operation has been called,
and decide whether to just add the buffer to an internal queue, or also
trigger a hardware run. vb2_is_streaming() relies on the vb2_queue
structure's streaming field, which used to be set only after calling the
.start_streaming() operation.
Commit a10b215325 ("media: vb2: add (un)prepare_streaming queue ops")
changed this, setting the .streaming field in vb2_core_streamon() before
enqueuing buffers to the driver and calling .start_streaming(). This
broke the vsp1 driver which now believes that .start_streaming() has
been called when it hasn't, leading to a crash:
[ 881.058705] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000020
[ 881.067495] Mem abort info:
[ 881.070290] ESR = 0x0000000096000006
[ 881.074042] EC = 0x25: DABT (current EL), IL = 32 bits
[ 881.079358] SET = 0, FnV = 0
[ 881.082414] EA = 0, S1PTW = 0
[ 881.085558] FSC = 0x06: level 2 translation fault
[ 881.090439] Data abort info:
[ 881.093320] ISV = 0, ISS = 0x00000006
[ 881.097157] CM = 0, WnR = 0
[ 881.100126] user pgtable: 4k pages, 48-bit VAs, pgdp=000000004fa51000
[ 881.106573] [0000000000000020] pgd=080000004f36e003, p4d=080000004f36e003, pud=080000004f7ec003, pmd=0000000000000000
[ 881.117217] Internal error: Oops: 0000000096000006 [#1] PREEMPT SMP
[ 881.123494] Modules linked in: rcar_fdp1 v4l2_mem2mem
[ 881.128572] CPU: 0 PID: 1271 Comm: yavta Tainted: G B 6.2.0-rc1-00023-g6c94e2e99343 #556
[ 881.138061] Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT)
[ 881.145981] pstate: 400000c5 (nZcv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 881.152951] pc : vsp1_dl_list_add_body+0xa8/0xe0
[ 881.157580] lr : vsp1_dl_list_add_body+0x34/0xe0
[ 881.162206] sp : ffff80000c267710
[ 881.165522] x29: ffff80000c267710 x28: ffff000010938ae8 x27: ffff000013a8dd98
[ 881.172683] x26: ffff000010938098 x25: ffff000013a8dc00 x24: ffff000010ed6ba8
[ 881.179841] x23: ffff00000faa4000 x22: 0000000000000000 x21: 0000000000000020
[ 881.186998] x20: ffff00000faa4000 x19: 0000000000000000 x18: 0000000000000000
[ 881.194154] x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000
[ 881.201309] x14: 0000000000000000 x13: 746e696174206c65 x12: ffff70000157043d
[ 881.208465] x11: 1ffff0000157043c x10: ffff70000157043c x9 : dfff800000000000
[ 881.215622] x8 : ffff80000ab821e7 x7 : 00008ffffea8fbc4 x6 : 0000000000000001
[ 881.222779] x5 : ffff80000ab821e0 x4 : ffff70000157043d x3 : 0000000000000020
[ 881.229936] x2 : 0000000000000020 x1 : ffff00000e4f6400 x0 : 0000000000000000
[ 881.237092] Call trace:
[ 881.239542] vsp1_dl_list_add_body+0xa8/0xe0
[ 881.243822] vsp1_video_pipeline_run+0x270/0x2a0
[ 881.248449] vsp1_video_buffer_queue+0x1c0/0x1d0
[ 881.253076] __enqueue_in_driver+0xbc/0x260
[ 881.257269] vb2_start_streaming+0x48/0x200
[ 881.261461] vb2_core_streamon+0x13c/0x280
[ 881.265565] vb2_streamon+0x3c/0x90
[ 881.269064] vsp1_video_streamon+0x2fc/0x3e0
[ 881.273344] v4l_streamon+0x50/0x70
[ 881.276844] __video_do_ioctl+0x2bc/0x5d0
[ 881.280861] video_usercopy+0x2a8/0xc80
[ 881.284704] video_ioctl2+0x20/0x40
[ 881.288201] v4l2_ioctl+0xa4/0xc0
[ 881.291525] __arm64_sys_ioctl+0xe8/0x110
[ 881.295543] invoke_syscall+0x68/0x190
[ 881.299303] el0_svc_common.constprop.0+0x88/0x170
[ 881.304105] do_el0_svc+0x4c/0xf0
[ 881.307430] el0_svc+0x4c/0xa0
[ 881.310494] el0t_64_sync_handler+0xbc/0x140
[ 881.314773] el0t_64_sync+0x190/0x194
[ 881.318450] Code: d50323bf d65f03c0 91008263 f9800071 (885f7c60)
[ 881.324551] ---[ end trace 0000000000000000 ]---
[ 881.329173] note: yavta[1271] exited with preempt_count 1
A different regression report sent to the linux-media mailing list ([1])
was answered with a claim that the vb2_is_streaming() function has never
been meant for this purpose. The document of the function, as well as of
the struct vb2_queue streaming field, is sparse, so this claim may be
hard to verify.
The information needed by the vsp1 driver to decide how to process
queued buffers is also available from the vb2_start_streaming_called()
function. Use it instead of vb2_is_streaming() to fix the problem.
[1] https://lore.kernel.org/linux-media/545610e7-3446-2b82-60dc-7385fea3774f@redhat.com/
Fixes: a10b215325 ("media: vb2: add (un)prepare_streaming queue ops")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Duy Nguyen <duy.nguyen.rh@renesas.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30cf57da17 ]
In saa7134_initdev, it will call saa7134_hwinit1. There are three
function invoking here: saa7134_video_init1, saa7134_ts_init1
and saa7134_vbi_init1.
All of them will init a timer with same function. Take
saa7134_video_init1 as an example. It'll bound &dev->video_q.timeout
with saa7134_buffer_timeout.
In buffer_activate, the timer funtcion is started.
If we remove the module or device which will call saa7134_finidev
to make cleanup, there may be a unfinished work. The
possible sequence is as follows, which will cause a
typical UAF bug.
Fix it by canceling the timer works accordingly before cleanup in
saa7134_finidev.
CPU0 CPU1
|saa7134_buffer_timeout
saa7134_finidev |
kfree(dev); |
|
| saa7134_buffer_next
| //use dev
Fixes: 1e7126b4a8 ("media: saa7134: Convert timers to use timer_setup()")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5abda7a166 ]
In dm1105_probe, it called dm1105_ir_init and bound
&dm1105->ir.work with dm1105_emit_key.
When it handles IRQ request with dm1105_irq,
it may call schedule_work to start the work.
When we call dm1105_remove to remove the driver, there
may be a sequence as follows:
Fix it by finishing the work before cleanup in dm1105_remove
CPU0 CPU1
|dm1105_emit_key
dm1105_remove |
dm1105_ir_exit |
rc_unregister_device |
rc_free_device |
rc_dev_release |
kfree(dev); |
|
| rc_keydown
| //use
Fixes: 34d2f9bf18 ("V4L/DVB: dm1105: use dm1105_dev & dev instead of dm1105dvb")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aec8298c09 ]
The current SMN index used for the driver probe seems to be meant
for the BIOS pair and there are potential concurrency problems that can
occur with an inopportune SMI.
It is been advised to use SMN_INDEX_0 instead of SMN_INDEX_2, which is
what amd_nb.c provides and this function has protections to ensure that
only one caller can use it at a time.
Fixes: da5ce22df5 ("platform/x86/amd/pmf: Add support for PMF core layer")
Co-developed-by: Patil Rajesh Reddy <Patil.Reddy@amd.com>
Signed-off-by: Patil Rajesh Reddy <Patil.Reddy@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Link: https://lore.kernel.org/r/20230406164807.50969-4-Shyam-sundar.S-k@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3228cec23b ]
In rkvdec_probe, rkvdec->watchdog_work is bound with
rkvdec_watchdog_func. Then rkvdec_vp9_run may
be called to start the work.
If we remove the module which will call rkvdec_remove
to make cleanup, there may be a unfinished work.
The possible sequence is as follows, which will
cause a typical UAF bug.
Fix it by canceling the work before cleanup in rkvdec_remove.
CPU0 CPU1
|rkvdec_watchdog_func
rkvdec_remove |
rkvdec_v4l2_cleanup|
v4l2_m2m_release |
kfree(m2m_dev); |
|
| v4l2_m2m_get_curr_priv
| m2m_dev->curr_ctx //use
Fixes: cd33c83044 ("media: rkvdec: Add the rkvdec driver")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50d0a7aea4 ]
In cedrus_probe, dev->watchdog_work is bound with cedrus_watchdog function.
In cedrus_device_run, it will started by schedule_delayed_work. If there is
an unfinished work in cedrus_remove, there may be a race condition and
trigger UAF bug.
CPU0 CPU1
|cedrus_watchdog
cedrus_remove |
v4l2_m2m_release |
kfree(m2m_dev) |
|
| v4l2_m2m_get_curr_priv
| m2m_dev //use
Fix it by canceling the worker in cedrus_remove.
Fixes: 7c38a551bd ("media: cedrus: Add watchdog for job completion")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e0ef56d81 ]
Putting core work to work queue using queue_work maybe fail, call
queue_work again when the count of core work in work queue is less
than core_list_cnt, making sure all the buffer in core list can be
scheduled.
Fixes: 365e4ba01d ("media: mtk-vcodec: Add work queue for core hardware decode")
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2cfca6c1bf ]
Current instance will decode done when begin to wait lat buf full,
move the lat_buf of current instance to the top of core list to make
sure current instance's lat_buf will be used firstly.
Fixes: 365e4ba01d ("media: mtk-vcodec: Add work queue for core hardware decode")
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68c7df5276 ]
While the decoder can produce frames in both MM21 and MT21C formats, only
MM21 is currently supported by userspace tools (like gstreamer and libyuv).
In order to ensure userspace keeps working after the SCP firmware is
updated to support both MM21 and MT21C formats, force the MM21 format for
the capture queue.
This is meant as a stopgap solution while dynamic format switching between
MM21 and MT21C isn't implemented in the driver.
Fixes: 7501edef6b ("media: mediatek: vcodec: Different codec using different capture format")
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: Nicolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Nicolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d020d81b9 ]
Given that only the MM21 capture format is supported by userspace tools
(like gstreamer and libyuv), make it the default capture format.
This allows us to force the MM21 format even when a MM21 and MT21C capable
firmware is available (which is needed while dynamic format switching isn't
implemented in the driver), without causing the following regressions on
v4l2-compliance:
fail: v4l2-test-formats.cpp(478): pixelformat 3132544d (MT21) for buftype 9 not reported by ENUM_FMT
test VIDIOC_G_FMT: FAIL
fail: v4l2-test-formats.cpp(478): pixelformat 3132544d (MT21) for buftype 9 not reported by ENUM_FMT
test VIDIOC_TRY_FMT: FAIL
fail: v4l2-test-formats.cpp(478): pixelformat 3132544d (MT21) for buftype 9 not reported by ENUM_FMT
test VIDIOC_S_FMT: FAIL
Fixes: 7501edef6b ("media: mediatek: vcodec: Different codec using different capture format")
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: Nicolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Nicolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e25528e1db ]
After commit b018be06f3 ("media: mediatek: vcodec: Read max resolution
from dec_capability"), the stateful video decoder driver never really
sets its output frame size to 4K.
Parse the decoder capability reported by the firmware, and update the
output frame size in mtk_init_vdec_params to enable 4K frame size when
available.
Fixes: b018be06f3 ("media: mediatek: vcodec: Read max resolution from dec_capability")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86379bd9d3 ]
1. Move removing buffer after sw setting and before hw setting
in enc&dec worker to prevents the operation of removing
the buffer twice if the sw setting fails.
2. Remove the redundant operation of queue work in the
jpegenc irq handler because the jpegenc worker has called
v4l2_m2m_job_finish to do it.
Fixes: 5fb1c2361e ("mtk-jpegenc: add jpeg encode worker interface")
Fixes: dedc215003 ("media: mtk-jpegdec: add jpeg decode worker interface")
Signed-off-by: kyrie wu <kyrie.wu@mediatek.com>
Signed-off-by: irui wang <irui.wang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f96fb2df3e ]
The detection of atomic update failure in reserve_eilvt_offset() is
not correct. The value returned by atomic_cmpxchg() should be compared
to the old value from the location to be updated.
If these two are the same, then atomic update succeeded and
"eilvt_offsets[offset]" location is updated to "new" in an atomic way.
Otherwise, the atomic update failed and it should be retried with the
value from "eilvt_offsets[offset]" - exactly what atomic_try_cmpxchg()
does in a correct and more optimal way.
Fixes: a68c439b19 ("apic, x86: Check if EILVT APIC registers are available (AMD only)")
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20230227160917.107820-1-ubizjak@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 13f03bcd02 ]
The binary representation for sensor 1 interrupt status was incorrectly
assembled, when compared to the full table given in the same comment
section. The conversion into hex was also incorrect, leading to
incorrect interrupt status bitmask for sensor 1. This would cause the
driver to incorrectly identify changes for sensor 1, when in fact it
was sensor 0, or a sensor access time out.
Fix the binary and hex representations in the comments, and the actual
bitmask macro.
Fixes: f5f633b182 ("thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230328031017.1360976-1-wenst@chromium.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4760be481d ]
With gcc-5 and CONFIG_UBSAN_SHIFT=y:
drivers/gpu/drm/msm/msm_mdss.c: In function 'msm_mdss_enable':
drivers/gpu/drm/msm/msm_mdss.c:296:2: error: case label does not reduce to an integer constant
case DPU_HW_VER_800:
^
drivers/gpu/drm/msm/msm_mdss.c:299:2: error: case label does not reduce to an integer constant
case DPU_HW_VER_810:
^
drivers/gpu/drm/msm/msm_mdss.c:300:2: error: case label does not reduce to an integer constant
case DPU_HW_VER_900:
^
This happens because for major revisions 8 or greather, the non-sign bit
of the major revision number is shifted into bit 31 of a signed integer,
which is undefined behavior.
Fix this by casting the major revision number to unsigned int.
Fixes: efcd010772 ("drm/msm/dpu: add support for SM8550")
Fixes: 4a352c2fc1 ("drm/msm/dpu: Introduce SC8280XP")
Fixes: 100d7ef699 ("drm/msm/dpu: add support for SM8450")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/525152/
Link: https://lore.kernel.org/r/20230306090633.65918-1-geert+renesas@glider.be
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 652eadfde8 ]
This reverts commit 8636500300.
A recent commit tried to address a drm device leak in the early
msm_drm_uninit() error paths but ended up making things worse.
Specifically, it moved the drm device reference put in msm_drm_uninit()
to msm_drm_init() which means that the drm would now be leaked on normal
unbind.
For reasons that were never spelled out, it also added kms NULL pointer
checks to a couple of helper functions that had nothing to do with the
paths modified by the patch.
Instead of trying to salvage this incrementally, let's revert the bad
commit so that clean and backportable fixes can be added in its place.
Fixes: 8636500300 ("drm/msm: Fix failure paths in msm_drm_init()")
Cc: Akhil P Oommen <quic_akhilpo@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/525092/
Link: https://lore.kernel.org/r/20230306100722.28485-3-johan+linaro@kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dfa70344d1 ]
This reverts commit 643b7d0869.
A recent patch that tried to fix up the msm_drm_init() paths with
respect to the workqueue but only ended up making things worse:
First, the newly added calls to msm_drm_uninit() on early errors would
trigger NULL-pointer dereferences, for example, as the kms pointer would
not have been initialised. (Note that these paths were also modified by
a second broken error handling patch which in effect cancelled out this
part when merged.)
Second, the newly added allocation sanity check would still leak the
previously allocated drm device.
Instead of trying to salvage what was badly broken (and clearly not
tested), let's revert the bad commit so that clean and backportable
fixes can be added in its place.
Fixes: 643b7d0869 ("drm/msm: Add missing check and destroy for alloc_ordered_workqueue")
Cc: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/525107/
Link: https://lore.kernel.org/r/20230306100722.28485-2-johan+linaro@kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cba6cfdc7c ]
An automated bot told me that there was a potential lockdep problem
with regulators. This was on the chromeos-5.15 kernel, but I see
nothing that would be different downstream compared to upstream. The
bot said:
============================================
WARNING: possible recursive locking detected
5.15.104-lockdep-17461-gc1e499ed6604 #1 Not tainted
--------------------------------------------
kworker/u16:4/115 is trying to acquire lock:
ffffff8083110170 (regulator_ww_class_mutex){+.+.}-{3:3}, at: create_regulator+0x398/0x7ec
but task is already holding lock:
ffffff808378e170 (regulator_ww_class_mutex){+.+.}-{3:3}, at: ww_mutex_trylock+0x3c/0x7b8
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(regulator_ww_class_mutex);
lock(regulator_ww_class_mutex);
*** DEADLOCK ***
May be due to missing lock nesting notation
4 locks held by kworker/u16:4/115:
#0: ffffff808006a948 ((wq_completion)events_unbound){+.+.}-{0:0}, at: process_one_work+0x520/0x1348
#1: ffffffc00e0a7cc0 ((work_completion)(&entry->work)){+.+.}-{0:0}, at: process_one_work+0x55c/0x1348
#2: ffffff80828a2260 (&dev->mutex){....}-{3:3}, at: __device_attach_async_helper+0xd0/0x2a4
#3: ffffff808378e170 (regulator_ww_class_mutex){+.+.}-{3:3}, at: ww_mutex_trylock+0x3c/0x7b8
stack backtrace:
CPU: 2 PID: 115 Comm: kworker/u16:4 Not tainted 5.15.104-lockdep-17461-gc1e499ed6604 #1 9292e52fa83c0e23762b2b3aa1bacf5787a4d5da
Hardware name: Google Quackingstick (rev0+) (DT)
Workqueue: events_unbound async_run_entry_fn
Call trace:
dump_backtrace+0x0/0x4ec
show_stack+0x34/0x50
dump_stack_lvl+0xdc/0x11c
dump_stack+0x1c/0x48
__lock_acquire+0x16d4/0x6c74
lock_acquire+0x208/0x750
__mutex_lock_common+0x11c/0x11f8
ww_mutex_lock+0xc0/0x440
create_regulator+0x398/0x7ec
regulator_resolve_supply+0x654/0x7c4
regulator_register_resolve_supply+0x30/0x120
class_for_each_device+0x1b8/0x230
regulator_register+0x17a4/0x1f40
devm_regulator_register+0x60/0xd0
reg_fixed_voltage_probe+0x728/0xaec
platform_probe+0x150/0x1c8
really_probe+0x274/0xa20
__driver_probe_device+0x1dc/0x3f4
driver_probe_device+0x78/0x1c0
__device_attach_driver+0x1ac/0x2c8
bus_for_each_drv+0x11c/0x190
__device_attach_async_helper+0x1e4/0x2a4
async_run_entry_fn+0xa0/0x3ac
process_one_work+0x638/0x1348
worker_thread+0x4a8/0x9c4
kthread+0x2e4/0x3a0
ret_from_fork+0x10/0x20
The problem was first reported soon after we made many of the
regulators probe asynchronously, though nothing I've seen implies that
the problems couldn't have also happened even without that.
I haven't personally been able to reproduce the lockdep issue, but the
issue does look somewhat legitimate. Specifically, it looks like in
regulator_resolve_supply() we are holding a "rdev" lock while calling
set_supply() -> create_regulator() which grabs the lock of a
_different_ "rdev" (the one for our supply). This is not necessarily
safe from a lockdep perspective since there is no documented ordering
between these two locks.
In reality, we should always be locking a regulator before the
supplying regulator, so I don't expect there to be any real deadlocks
in practice. However, the regulator framework in general doesn't
express this to lockdep.
Let's fix the issue by simply grabbing the two locks involved in the
same way we grab multiple locks elsewhere in the regulator framework:
using the "wound/wait" mechanisms.
Fixes: eaa7995c52 ("regulator: core: avoid regulator_resolve_supply() race condition")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230329143317.RFC.v2.2.I30d8e1ca10cfbe5403884cdd192253a2e063eb9e@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b83a1772be ]
When a codepath locks a rdev using ww_mutex_lock_slow() directly then
that codepath is responsible for incrementing the "ref_cnt" and also
setting the "mutex_owner" to "current".
The regulator core consistently got that right for "ref_cnt" but
didn't always get it right for "mutex_owner". Let's fix this.
It's unlikely that this truly matters because the "mutex_owner" is
only needed if we're going to do subsequent locking of the same
rdev. However, even though it's not truly needed it seems less
surprising if we consistently set "mutex_owner" properly.
Fixes: f8702f9e4a ("regulator: core: Use ww_mutex for regulators locking")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230329143317.RFC.v2.1.I4e9d433ea26360c06dd1381d091c82bb1a4ce843@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69e6dd1492 ]
MESA driver is creating protected context on every driver handle
creation to query caps bits for app. So when running CI tests,
they are observing hundreds of drm_errors when enabling PXP
in .config but using SOC fusing or BIOS configuration that cannot
support PXP sessions.
The fixes tag referenced below was to resolve a related issue
where we wanted to silence error messages, but that case was due
to outdated IFWI (firmware) that definitely needed an upgrade and
was, at that point, considered a one-off case as opposed to today's
realization that default CI was enabling PXP in kernel config for
all testing.
So with this patch, let's strike a balance between issues that is
critical but are root-caused from HW/platform gaps (louder drm-warn
but just ONCE) vs other cases where it could also come from session
state machine (which cannot be a WARN_ONCE since it can be triggered
due to runtime operation events).
Let's use helpers for these so as more functions are added in future
features / HW (or as FW designers continue to bless upstreaming of
the error codes and meanings), we only need to update the helpers.
NOTE: Don't completely remove FW errors (via drm_debug) or else cusomer
apps that really needs to know that content protection failed won't
be aware of it.
v2: - Add fixes tag (Trvtko)
v3: - Break multi-line drm_dbg strings into separate drm_dbg (Daniele)
- Fix couple of typecasting nits (Daniele)
v4: - Unsuccessful PXP FW cmd due to platform configuration shouldn't
use drm_WARN_once (Tvrtko), Switched to use drm_info_once.
v5: - Added "reported-and-tested" by Eero.
Reported-and-tested-by: Eero Tamminen <eero.t.tamminen@intel.com>
Fixes: b762787bf7 ("drm/i915/pxp: Use drm_dbg if arb session failed due to fw version")
Signed-off-by: Alan Previn <alan.previn.teres.alexis@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323184156.4140659-1-alan.previn.teres.alexis@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d374c047b3 ]
A gap was recently discovered where if an application did not
invalidate all of the stream keys (intentionally or not), and the
driver did a full PXP global teardown on the GT subsystem, we
find that future session creation would fail on the security
firmware's side of the equation. i915 is the entity that needs
ensure the sessions' state across both iGT and security firmware
are at a known clean point when performing a full global teardown.
Architecturally speaking, i915 should inspect all active sessions
and submit the invalidate-stream-key PXP command to the security
firmware for each of them. However, for the upstream i915 driver
we only support the arbitration session that can be created
so that will be the only session we will cleanup.
Signed-off-by: Alan Previn <alan.previn.teres.alexis@intel.com>
Reviewed-by: Juston Li <justonli@chromium.org>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230125082637.118970-5-alan.previn.teres.alexis@intel.com
Stable-dep-of: 69e6dd1492 ("drm/i915/pxp: limit drm-errors or warning on firmware API failures")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97b4fdc6b8 ]
This reverts commit 46546f2882 because it
mistakenly took PMIC pinctrl/GPIO as TLMM. The TLMM pinctrl uses "gpio"
function, but PMIC uses "normal", so original code was correct:
msm8998-oneplus-cheeseburger.dtb: pmic@2: gpio@c000:button-backlight-state: 'oneOf' conditional failed, one must be fixed:
'gpio' is not one of ['normal', 'paired', 'func1', 'func2', 'dtest1', 'dtest2', 'dtest3', 'dtest4', 'func3', 'func4']
Fixes: 46546f2882 ("arm64: dts: qcom: msm8998-oneplus-cheeseburger: fix backlight pin function")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230312183622.460488-5-krzysztof.kozlowski@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55879dad0f ]
The device names allocated by dev_set_name() need be freed
before module unloading, but they can not be freed because
the kobject's refcount which was set in device_initialize()
has not be decreased to 0.
As comment of device_add() says, if it fails, use only
put_device() drop the refcount, then the name will be
freed in kobejct_cleanup().
device_del() and put_device() can be replaced with
device_unregister(), so call it to unregister the added
successfully devices, and just call put_device() to the
not added device.
Add a release() function to device to avoid null release()
function WARNING in device_release(), it's empty, because
the context devices are freed together in
host1x_memory_context_list_free().
Fixes: 8aa5bcb616 ("gpu: host1x: Add context device management code")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8466ff24a3 ]
If context device has no IOMMU, the 'cdl->devs' is freed in
error path, but host1x_memory_context_list_init() doesn't
return an error code, so the module can be loaded successfully,
when it's unloading, the host1x_memory_context_list_free() is
called in host1x_remove(), it will cause double free. Set the
'cdl->devs' to NULL after freeing it to avoid double free.
Fixes: 8aa5bcb616 ("gpu: host1x: Add context device management code")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3fbced9af ]
Smatch reports:
drivers/soc/bcm/brcmstb/biuctrl.c:291 setup_hifcpubiuctrl_regs() warn:
'cpubiuctrl_base' from of_iomap() not released on lines: 291.
This is because in setup_hifcpubiuctrl_regs(),
cpubiuctrl_base is not released when handle error, which may cause a leak.
To fix this, iounmap is added when handle error.
Fixes: 22f7a9116e ("soc: brcmstb: Correct CPU_CREDIT_REG offset for Brahma-B53 CPUs")
Signed-off-by: Zhaoyang Li <lizhaoyang04@hust.edu.cn>
Reviewed-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/r/20230327115422.1536615-1-lizhaoyang04@hust.edu.cn
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b5984a9844 ]
The system controller on PolarFire SoC has no interrupt to signify that
the TX has been completed. The interrupt instead signals that a service
requested by the mailbox client has succeeded. If a service fails, there
will be no interrupt delivered.
Switch to polling the busy register to determine whether transmission
has completed.
Fixes: 83d7b15608 ("mbox: add polarfire soc system controller mailbox")
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Tested-by: Valentina Fernandez <valentina.fernandezalanis@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47d2668418 ]
When setting up DMA for a PCI device, we need to initialize its
iommu_fwspec with all possible alias RIDs (such as PCI bridges). To do
this we use pci_for_each_dma_alias() which calls
viot_pci_dev_iommu_init(). This function incorrectly initializes the
fwspec of the bridge instead of the device being configured. Fix it by
passing the original device as context to pci_for_each_dma_alias().
Fixes: 3cf485540e ("ACPI: Add driver for the VIOT table")
Link: https://lore.kernel.org/all/Y8qzOKm6kvhGWG1T@myrica
Reported-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e2b47e5859 ]
The OSM/EPSS hardware controls the frequency of each CPU cluster based
on requests from the OS and various throttling events in the system.
While throttling is in effect the related dcvs interrupt will be kept
high. The purpose of the code handling this interrupt is to
continuously report the thermal pressure based on the throttled
frequency.
The reasoning for adding QoS control to this mechanism is not entirely
clear, but the introduction of commit 'c4c0efb06f17 ("cpufreq:
qcom-cpufreq-hw: Add cpufreq qos for LMh")' causes the
scaling_max_frequncy to be set to the throttled frequency. On the next
iteration of polling, the throttled frequency is above or equal to the
newly requested frequency, so the polling is stopped.
With cpufreq limiting the max frequency, the hardware no longer report a
throttling state and no further updates to thermal pressure or qos
state are made.
The result of this is that scaling_max_frequency can only go down, and
the system becomes slower and slower every time a thermal throttling
event is reported by the hardware.
Even if the logic could be improved, there is no reason for software to
limit the max freqency in response to the hardware limiting the max
frequency. At best software will follow the reported hardware state, but
typically it will cause slower backoff of the throttling.
This reverts commit c4c0efb06f.
Fixes: c4c0efb06f ("cpufreq: qcom-cpufreq-hw: Add cpufreq qos for LMh")
Reported-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0883426fd0 ]
During the addition of SRAM voltage tracking for CCI scaling, this
driver got some voltage limits set for the vtrack algorithm: these
were moved to platform data first, then enforced in a later commit
6a17b3876b ("cpufreq: mediatek: Refine mtk_cpufreq_voltage_tracking()")
using these as max values for the regulator_set_voltage() calls.
In this case, the vsram/vproc constraints for MT7622 and MT7623
were supposed to be the same as MT2701 (and a number of other SoCs),
but that turned out to be a mistake because the aforementioned two
SoCs' maximum voltage for both VPROC and VPROC_SRAM is 1.36V.
Fix that by adding new platform data for MT7622/7623 declaring the
right {proc,sram}_max_volt parameter.
Fixes: ead858bd12 ("cpufreq: mediatek: Move voltage limits to platform data")
Fixes: 6a17b3876b ("cpufreq: mediatek: Refine mtk_cpufreq_voltage_tracking()")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Jia-Wei Chang <jia-wei.chang@mediatek.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3296bb4ca ]
Since the upper boundary of proc/sram voltage of MT8516 is 1300 mV,
which is greater than the value of MT2701 1150 mV, we fix it by adding
the corresponding platform data and specify proc/sram_max_volt to
support MT8516.
Signed-off-by: Jia-Wei Chang <jia-wei.chang@mediatek.com>
Fixes: ead858bd12 ("cpufreq: mediatek: Move voltage limits to platform data")
Fixes: 6a17b3876b ("cpufreq: mediatek: Refine mtk_cpufreq_voltage_tracking()")
Reported-by: Nick Hainke <vincent@systemli.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d51e106240 ]
Any kind of failure in mtk_cpu_dvfs_info_init() will lead to calling
regulator_put() or clk_put() and the KP will occur since the regulator/clk
handlers are used after released in mtk_cpu_dvfs_info_release().
To prevent the usage after regulator_put()/clk_put(), the regulator/clk
handlers are addressed in a way of "Free the Last Thing Style".
Signed-off-by: Jia-Wei Chang <jia-wei.chang@mediatek.com>
Fixes: 4b9ceb757b ("cpufreq: mediatek: Enable clocks and regulators")
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Suggested-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0189fdfb7 ]
The PCIe ports are unused (without devices) so disable them instead of
removing them.
Fixes: 7c77ab91b3 ("arm64: dts: apple: Add missing M1 (t8103) devices")
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b9f0ec81a ]
Bank A and B IOs can't be handled by the pin controller 'Z'. This patch
assign spi1 pin definition to the correct controller.
Fixes: 9ad65d245b ("ARM: dts: stm32: stm32mp15-pinctrl: add spi1-1 pinmux group")
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2ccba9e8c ]
Two distinct pools of xfer descriptors are allocated at initialization
time: one (Tx) used to provide xfers to track commands and their replies
(or delayed replies) and another (Rx) to pick xfers from to be used for
processing notifications.
Such pools, though, are allocated globally to be used by the whole SCMI
instance, they are not allocated per-channel and as such the allocation of
notifications xfers cannot be simply skipped if no Rx channel was found for
the base protocol common channel, because there could be defined more
optional per-protocol dedicated channels that instead support Rx channels.
Change the conditional check to skip allocation for the notification pool
only if no Rx channel has been detected on any per-channel protocol at all.
Fixes: 4ebd8f6dea ("firmware: arm_scmi: Add receive buffer support for notifications")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20230326203449.3492948-1-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a622310f7f ]
OMAP processors support 32 channels but there is no check or
inspect this except booting a device and looking at dmesg reports
of not available channels.
Recently some more subsystems with DMA (aes1+2) were added filling
the list of dma channels beyond the limit of 32 (even if other
parameters indicate 96 or 128 channels). This leads to random
subsystem failures i(e.g. mcbsp for audio) after boot or boot
messages that DMA can not be initialized.
Another symptom is that
/sys/kernel/debug/dmaengine/summary
has 32 entries and does not show all required channels.
Fix by disabling unused (on the GTA04 hardware) mcspi1...4.
Each SPI channel allocates 4 DMA channels rapidly filling
the available ones.
Disabling unused SPI modules on the OMAP3 SoC may also save
some energy (has not been checked).
Fixes: c312f06631 ("ARM: dts: omap3: Migrate AES from hwmods to sysc-omap2")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
[re-enabled aes2, improved commit subject line]
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Message-Id: <20230113211151.2314874-1-andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0dd8316037 ]
If spec_reg is equal to 'SDHCI_PRESENT_STATE', esdhc_readl_fixup()
fixes up register value and returns it immediately. As a result, the
further block
(spec_reg == SDHCI_PRESENT_STATE)
&&(esdhc->quirk_ignore_data_inhibit == true),
is never executed.
The patch merges the second block into the first one.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 1f1929f3f2 ("mmc: sdhci-of-esdhc: add quirk to ignore command inhibit for data")
Signed-off-by: Georgii Kruglov <georgy.kruglov@yandex.ru>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230321203715.3975-1-georgy.kruglov@yandex.ru
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 073828e954 ]
In ACPI systems, the OS can direct power management, as opposed to the
firmware. This OS-directed Power Management is called OSPM. Part of
telling the firmware that the OS going to direct power management is
making ACPI "_PDC" (Processor Driver Capabilities) calls. These _PDC
methods must be evaluated for every processor object. If these _PDC
calls are not completed for every processor it can lead to
inconsistency and later failures in things like the CPU frequency
driver.
In a Xen system, the dom0 kernel is responsible for system-wide power
management. The dom0 kernel is in charge of OSPM. However, the
number of CPUs available to dom0 can be different than the number of
CPUs physically present on the system.
This leads to a problem: the dom0 kernel needs to evaluate _PDC for
all the processors, but it can't always see them.
In dom0 kernels, ignore the existing ACPI method for determining if a
processor is physically present because it might not be accurate.
Instead, ask the hypervisor for this information.
Fix this by introducing a custom function to use when running as Xen
dom0 in order to check whether a processor object matches a CPU that's
online. Such checking is done using the existing information fetched
by the Xen pCPU subsystem, extending it to also store the ACPI ID.
This ensures that _PDC method gets evaluated for all physically online
CPUs, regardless of the number of CPUs made available to dom0.
Fixes: 5d554a7bb0 ("ACPI: processor: add internal processor_physically_present()")
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4082b9f5ea ]
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:157:21: note: in expansion of macro ‘mmCRTC1_DCFE_MEM_LIGHT_SLEEP_CNTL’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_transform.h:170:9: note: in expansion of macro ‘SRI’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:183:17: note: in expansion of macro ‘XFM_COMMON_REG_LIST_DCE60’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:188:17: note: in expansion of macro ‘transform_regs’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_6_0_d.h:722:43: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:157:21: note: in expansion of macro ‘mmCRTC2_DCFE_MEM_LIGHT_SLEEP_CNTL’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_transform.h:170:9: note: in expansion of macro ‘SRI’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:183:17: note: in expansion of macro ‘XFM_COMMON_REG_LIST_DCE60’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:189:17: note: in expansion of macro ‘transform_regs’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_6_0_d.h:722:43: note: (near initialization for ‘xfm_regs[2].DCFE_MEM_LIGHT_SLEEP_CN
[100 lines snipped for brevity]
Fixes: ceb3cf476a ("drm/amd/display/dc/dce60/Makefile: Ignore -Woverride-init warning")
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "Pan, Xinhui" <Xinhui.Pan@amd.com>
Cc: David Airlie <airlied@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Mauro Rossi <issor.oruam@gmail.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 965006103a ]
The encryption algorithms read and write directly to shared unencrypted
memory, which may leak information as well as permit the host to tamper
with the message integrity. Instead, copy whole messages in or out as
needed before doing any computation on them.
Fixes: d5af44dde5 ("x86/sev: Provide support for SNP guest request NAEs")
Signed-off-by: Dionna Glaze <dionnaglaze@google.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20230214164638.1189804-3-dionnaglaze@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c5a06e550 ]
acpi_evaluate_dsm_typed() needs to be gaurded with CONFIG_ACPI to avoid
a redefintion error when the stub is also enabled.
In file included from ../drivers/bluetooth/btintel.c:13:
../include/acpi/acpi_bus.h:57:1: error: redefinition of 'acpi_evaluate_dsm_typed'
57 | acpi_evaluate_dsm_typed(acpi_handle handle, const guid_t *guid,..
| ^~~~~~~~~~~~~~~~~~~~~~~
In file included from ../drivers/bluetooth/btintel.c:12:
../include/linux/acpi.h:967:34: note: previous definition of
'acpi_evaluate_dsm_typed' with type 'union acpi_object *(void *,
const guid_t *, u64, u64, union acpi_object *, acpi_object_type)'
{aka 'union acpi_object *(void *, const guid_t *, long long unsigned int,
long long unsigned int, union acpi_object *, unsigned int)'}
967 | static inline union acpi_object
*acpi_evaluate_dsm_typed(acpi_handle handle,
Fixes: 1b94ad7ccc ("ACPI: utils: Add acpi_evaluate_dsm_typed() and acpi_check_dsm() stubs")
Signed-off-by: Kiran K <kiran.k@intel.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d179f84f2 ]
Commit 2c204f3d53 ("accel: add dedicated minor for accelerator
devices") adds link to accelerator nodes section of DRM internals doc
(Documentation/gpu/drm-internals.rst), but the target doesn't exist.
Instead, there is only an introduction doc for computer accelerator
subsytem.
Link to that doc until there is documentation of accelerator internals.
Fixes: 2c204f3d53 ("accel: add dedicated minor for accelerator devices")
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee0285e134 ]
When dynamically switching lanes was removed, the intent of the code
was to check to make sure that higher speed items used 4 lanes, but
it had the unintended consequence of removing the slower speeds for
4-lane users.
This attempts to remedy this by doing a check to see that the
max frequency doesn't exceed the chip limit, and a second
check to make sure that the max bit-rate doesn't exceed the
number of lanes * max bit rate / lane.
Fixes: 9a0cdcd664 ("drm/bridge: adv7533: remove dynamic lane switching from adv7533 bridge")
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230319125524.58803-1-aford173@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eed9496a05 ]
The buf[4] value comes from the user via ts_play(). It is a value in
the u8 range. The final length we pass to av7110_ipack_instant_repack()
is "len - (buf[4] + 1) - 4" so add a check to ensure that the length is
not negative. It's not clear that passing a negative len value does
anything bad necessarily, but it's not best practice.
With the new bounds checking the "if (!len)" condition is no longer
possible or required so remove that.
Fixes: fd46d16d60 ("V4L/DVB (11759): dvb-ttpci: Add TS replay capability")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d00f592250 ]
Add the check for the return value of the ida_alloc in order to avoid
NULL pointer dereference.
Moreover, free allocated "ctx->id" if mdp_m2m_open fails later in order
to avoid memory leak.
Fixes: 61890ccaef ("media: platform: mtk-mdp3: add MediaTek MDP3 driver")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2371adeab7 ]
Add the check for the return value of the create_workqueue
in order to avoid NULL pointer dereference.
Fixes: 28ffeebbb7 ("[media] bdisp: 2D blitter driver using v4l2 mem2mem framework")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c1cdec319 ]
Thee maximum number of MCA banks is 64 (MAX_NR_BANKS), see
a0bc32b3ca ("x86/mce: Increase maximum number of banks to 64").
However, the bank_map which contains a bitfield of which banks to
initialize is of type unsigned int and that overflows when those bit
numbers are >= 32, leading to UBSAN complaining correctly:
UBSAN: shift-out-of-bounds in arch/x86/kernel/cpu/mce/amd.c:1365:38
shift exponent 32 is too large for 32-bit type 'int'
Change the bank_map to a u64 and use the proper BIT_ULL() macro when
modifying bits in there.
[ bp: Rewrite commit message. ]
Fixes: a0bc32b3ca ("x86/mce: Increase maximum number of banks to 64")
Signed-off-by: Muralidhara M K <muralimk@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20230127151601.1068324-1-muralimk@amd.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44750f1536 ]
While stressing EAS on my dragonboard RB3, I have noticed that LITTLE cores
where never selected as the most energy efficient CPU whatever the
utilization level of waking task.
energy model framework uses its cost field to estimate the energy with
the formula:
nrg = cost of the selected OPP * utilization / CPU's max capacity
which ends up selecting the CPU with lowest cost / max capacity ration
as long as the utilization fits in the OPP's capacity.
If we compare the cost of a little OPP with similar capacity of a big OPP
like :
OPP(kHz) OPP capacity cost max capacity cost/max capacity
LITTLE 1766400 407 351114 407 863
big 1056000 408 520267 1024 508
This can be interpreted as the LITTLE core consumes 70% more than big core
for the same compute capacity.
According to [1], LITTLE consumes 10% less than big core for Coremark
benchmark at those OPPs. If we consider that everything else stays
unchanged, the dynamic-power-coefficient of LITTLE core should be
only 53% of the current value: 290 * 53% = 154
Set the dynamic-power-coefficient of CPU0-3 to 154 to fix the energy model.
[1] https://github.com/kdrag0n/freqbench/tree/master/results/sdm845/main
Fixes: 0e0a8e35d7 ("arm64: dts: qcom: sdm845: correct dynamic power coefficients")
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230106164618.1845281-1-vincent.guittot@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 32734bbd18 ]
First, move the pinctrl related propeties out from SoC dtsi and into the
board dts and add blank lines before status properties in the PHY nodes
to be consistent with the rest of the nodes. Then drop the pipe clock
from the controller nodes. Rename the aggre0 and aggre1 clocks to more
generic noc_aggr, and then the cnoc_pcie_sf_axi to cnoc_sf_axi. Add the
cpu-pcie interconnects to both controller nodes. Rename the pcie1 second
reset to link_down and drop the unnecessary enable-gpios. Switch the aux
clock to GCC_PCIE_1_PHY_AUX_CLK for the pcie1 PHY and drop the aux_phy
from clock-names. Also rename the nocsr reset to phy_nocsr. With this
changes we are now in line with the SC8280XP bindings.
Fixes: 7d1158c984 ("arm64: dts: qcom: sm8550: Add PCIe PHYs and controllers nodes")
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230208180020.2761766-12-abel.vesa@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23be9f68f9 ]
This fixes:
arch/arm64/boot/dts/broadcom/bcmbca/bcm4908-asus-gt-ac5300.dtb: leds@800: 'led-lan@19', 'led-power@11', 'led-wan-red@12', 'led-wan-white@15', 'led-wps@14' do not match any of the regexes: '^led@[a-f0-9]+$', 'pinctrl-[0-9]+'
From schema: Documentation/devicetree/bindings/leds/leds-bcm63138.yaml
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/all/20230228144400.21689-2-zajec5@gmail.com/
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f4b30a777 ]
According to latest errata of J721e [1], (i2024) 'MMCSD: Peripherals
Do Not Support HS400' which applies to MMCSD0 subsystem. Speed modes
supported has been already updated but missed dropping 'ti,strobe-sel'
property which is only required by HS400 speed mode.
Thus, drop 'ti,strobe-sel' property from kernel dtsi for J721e SoC.
[1] https://www.ti.com/lit/er/sprz455/sprz455.pdf
Fixes: eb8f6194e8 ("arm64: dts: ti: k3-j721e-main: Update the speed modes supported and their itap delay values for MMCSD subsystems")
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Diwakar Dhyani <d-dhyani@ti.com>
Reviewed-by: Nitin Yadav <n-yadav@ti.com>
Link: https://lore.kernel.org/r/20230203073724.29529-1-b-kapoor@ti.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 691c1fcda5 ]
This is very close to a straight revert of commit 218320fec2
("regulator: core: Fix off-on-delay-us for always-on/boot-on
regulators"). We've identified that patch as causing a boot speed
regression on sc7180-trogdor boards. While boot speed certainly isn't
more important than making sure that power sequencing is correct,
looking closely at the original change it doesn't seem to have been
fully justified. It mentions "cycling issues" without describing
exactly what the issues were. That means it's possible that the
cycling issues were really a problem that should be fixed in a
different way.
Let's take a careful look at how we should handle regulators that have
an off-on-delay and that are boot-on or always-on. Linux currently
doesn't have any way to identify whether a GPIO regulator was already
on when the kernel booted. That means that when the kernel boots we
probe a regulator, see that it wants boot-on / always-on we, and then
turn the regulator on. We could be in one of two cases when we do
this:
a) The regulator might have been left on by the bootloader and we're
ensuring that it stays on.
b) The regulator might have been left off by the bootloader and we're
just now turning it on.
For case a) we definitely don't need any sort of delay. For case b) we
_might_ need some delay in case the bootloader turned the regulator
off _right_ before booting the kernel. To get the proper delay for
case b) then we can just assume a `last_off` of 0, which is what it
gets initialized to by default.
As per above, we can't tell whether we're in case a) or case b) so
we'll assume the longer delay (case b). This basically puts the code
to how it was before commit 218320fec2 ("regulator: core: Fix
off-on-delay-us for always-on/boot-on regulators"). However, we add
one important change: we make sure that the delay is actually honored
if `last_off` is 0. Though the original "cycling issues" cited were
vague, I'm hopeful that this important extra change will be enough to
fix the issues that the initial commit mentioned.
With this fix, I've confined that on a sc7180-trogdor board the delay
at boot goes down from 500 ms to ~250 ms. That's not as good as the 0
ms that we had prior to commit 218320fec2 ("regulator: core: Fix
off-on-delay-us for always-on/boot-on regulators"), but it's probably
safer because we don't know if the bootloader turned the regulator off
right before booting.
One note is that it's possible that we could be in a state that's not
a) or b) if there are other issues in the kernel. The only one I can
think of is related to pinctrl. If the pinctrl driver being used on a
board isn't careful about avoiding glitches when setting up a pin then
it's possible that setting up a pin could cause the regulator to "turn
off" briefly immediately before the regulator probes. If this is
indeed causing problems then the pinctrl driver should be fixed,
perhaps in a similar way to what was done in commit d21f4b7ffc
("pinctrl: qcom: Avoid glitching lines when we first mux to output")
Fixes: 218320fec2 ("regulator: core: Fix off-on-delay-us for always-on/boot-on regulators")
Cc: Christian Kohlschütter <christian@kohlschutter.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230313111806.1.I2eaad872be0932a805c239a7c7a102233fb0b03b@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71b1e3ba3f ]
The current DRAM row address mapping arrays skx_{open,close}_row[]
only support ranks with sizes up to 16G. Decoding a rank address
to a DRAM row address for a 32G rank by using either one of the
above arrays by the skx_edac driver, will result in an overflow on
the array.
For a 32G rank, the most significant DRAM row address bit (the
bit17) is mapped from the bit34 of the rank address. Add this new
mapping item to both arrays to fix the overflow issue.
Fixes: 4ec656bdf4 ("EDAC, skx_edac: Add EDAC driver for Skylake")
Reported-by: Feng Xu <feng.f.xu@intel.com>
Tested-by: Feng Xu <feng.f.xu@intel.com>
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/all/20230211011728.71764-1-qiuxu.zhuo@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 554edc3e92 ]
According to the RZ/G Series, 2nd Generation Hardware User’s Manual
Rev. 1.11, the System CPU cores on RZ/G2E do not have their own power
supply, but use the common internal power supply (typical 1.03V).
Hence remove the "opp-microvolt" properties from the Operating
Performance Points table. They are optional, and unused, when none of
the CPU nodes is tied to a regulator using the "cpu-supply" property.
Fixes: 231d8908a6 ("arm64: dts: renesas: r8a774c0: Add OPPs table for cpu devices")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/8348e18a011ded94e35919cd8e17c0be1f9acf2f.1676560856.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb76b0fae3 ]
According to the R-Car Series, 3rd Generation Hardware User’s Manual
Rev. 2.30, the System CPU cores on R-Car E3 do not have their own power
supply, but use the common internal power supply (typical 1.03V).
Hence remove the "opp-microvolt" properties from the Operating
Performance Points table. They are optional, and unused, when none of
the CPU nodes is tied to a regulator using the "cpu-supply" property.
Fixes: dd7188eb4e ("arm64: dts: renesas: r8a77990: Add OPPs table for cpu devices")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/9232578d9d395d529f64db3333a371e31327f459.1676560856.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f1732a868 ]
When the k3 ring accelerator driver has been modified to add module build
support, try_module_get() and module_put() have been added to update the
module refcnt. One code path has not been updated and it has introduced
an issue where the refcnt is decremented by module_put() in
k3_ringacc_ring_free() without being incremented previously.
Adding try_module_get() to k3_dmaring_request_dual_ring() ensures the
refcnt is kept up to date.
Fixes: c07f216a8b ("soc: ti: k3-ringacc: Allow the driver to be built as module")
Signed-off-by: Nicolas Frayer <nfrayer@baylibre.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20221230001404.10902-1-nfrayer@baylibre.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d37a3929ca ]
Commit 3840c5bcc2 ("drm/amdgpu: disentangle runtime pm and
vga_switcheroo") made amdgpu only register a vga_switcheroo client for
GPU's with PX, however AMD GPUs in dual gpu Apple Macbooks do need to
register, but don't have PX. Instead of AMD's PX, they use apple-gmux.
Use apple_gmux_detect() to identify these gpus, and
pci_is_thunderbolt_attached() to ensure eGPUs connected to Dual GPU
Macbooks don't register with vga_switcheroo.
Fixes: 3840c5bcc2 ("drm/amdgpu: disentangle runtime pm and vga_switcheroo")
Link: https://lore.kernel.org/amd-gfx/20230210044826.9834-10-orlandoch.dev@gmail.com/
Signed-off-by: Orlando Chamberlain <orlandoch.dev@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db217e84d0 ]
Fixes the following bindings check error:
- pwm@2000: clock-names: 'oneOf' conditional failed, one must be fixed:
['clkin4'] is too short
'clkin4' is not one of ['clkin0', 'clkin1']
'clkin0' was expected
- pwm@7000: clock-names: 'oneOf' conditional failed, one must be fixed:
['clkin3'] is too short
'clkin3' is not one of ['clkin0', 'clkin1']
'clkin0' was expected
- pwm@19000: clock-names: 'oneOf' conditional failed, one must be fixed:
['clkin2'] is too short
'clkin2' is not one of ['clkin0', 'clkin1']
'clkin0' was expected
Fixes: d747e7f76a ("arm64: dts: meson: add support for Radxa Zero2")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20230207-b4-amlogic-bindings-fixups-v2-v1-4-93b7e50286e7@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8e47884f1 ]
Currently we schedule a call to output_poll_execute from
drm_kms_helper_poll_enable for 10s in future. Later we try to replace
that in drm_helper_probe_single_connector_modes with a 0s schedule with
delayed_event set.
But as there is already a job in the queue this fails, and the immediate
job we wanted with delayed_event set doesn't occur until 10s later.
And that call acts as if connector state has changed, reprobing modes.
This has a side effect of waking up a display that has been blanked.
Make sure we cancel the old job before submitting the immediate one.
Fixes: 162b6a57ac ("drm/probe-helper: don't lose hotplug event")
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
[Maxime: Switched to mod_delayed_work]
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20230127154052.452524-1-maxime@cerno.tech
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 17ab1ea679 ]
When CONFIG_PM is disabled, the driver fails to build:
drivers/accel/ivpu/ivpu_pm.c: In function 'ivpu_rpm_get':
drivers/accel/ivpu/ivpu_pm.c:240:84: error: 'struct dev_pm_info' has no member named 'usage_count'
240 | ivpu_dbg(vdev, RPM, "rpm_get count %d\n", atomic_read(&vdev->drm.dev->power.usage_count));
| ^
include/linux/dynamic_debug.h:223:29: note: in definition of macro '__dynamic_func_call_cls'
223 | func(&id, ##__VA_ARGS__); \
| ^~~~~~~~~~~
include/linux/dynamic_debug.h:249:9: note: in expansion of macro '_dynamic_func_call_cls'
249 | _dynamic_func_call_cls(_DPRINTK_CLASS_DFLT, fmt, func, ##__VA_ARGS__)
| ^~~~~~~~~~~~~~~~~~~~~~
include/linux/dynamic_debug.h:272:9: note: in expansion of macro '_dynamic_func_call'
272 | _dynamic_func_call(fmt, __dynamic_dev_dbg, \
| ^~~~~~~~~~~~~~~~~~
include/linux/dev_printk.h:155:9: note: in expansion of macro 'dynamic_dev_dbg'
155 | dynamic_dev_dbg(dev, dev_fmt(fmt), ##__VA_ARGS__)
| ^~~~~~~~~~~~~~~
drivers/accel/ivpu/ivpu_drv.h:65:17: note: in expansion of macro 'dev_dbg'
65 | dev_dbg((vdev)->drm.dev, "[%s] " fmt, #type, ##args); \
| ^~~~~~~
drivers/accel/ivpu/ivpu_pm.c:240:9: note: in expansion of macro 'ivpu_dbg'
240 | ivpu_dbg(vdev, RPM, "rpm_get count %d\n", atomic_read(&vdev->drm.dev->power.usage_count));
| ^~~~~~~~
It would be possible to rework these statements to only conditionally print
the reference counter, or to make the driver depend on CONFIG_PM, but my
impression is that these are not actually needed at all if the driver generally
works, or they could be put back when required. Just remove all four of these
to make the driver build in all configurations.
Fixes: 852be13f3b ("accel/ivpu: Add PM support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230126163804.3648051-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d95debbdc5 ]
Commit 515bddf0ec ("selftests/clone3: test clone3 with CLONE_NEWTIME")
added an additional test, so the number passed to ksft_set_plan needs to
be bumped accordingly.
Also use ksft_finished() to print results and exit. This will catch future
mismatches between ksft_set_plan() and the number of tests being run.
Fixes: 515bddf0ec ("selftests/clone3: test clone3 with CLONE_NEWTIME")
Cc: Christian Brauner <brauner@kernel.org>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 955df4f877 ]
In tpm_tis_resume() make sure that the locality has been claimed when
tpm_tis_reenable_interrupts() is called. Otherwise the writings to the
register might not have any effect.
Fixes: 45baa1d1fa ("tpm_tis: Re-enable interrupts upon (S3) resume")
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a2f55d0be ]
Implement a usage counter for the (default) locality used by the TPM TIS
driver:
Request the locality from the TPM if it has not been claimed yet, otherwise
only increment the counter. Also release the locality if the counter is 0
otherwise only decrement the counter. Since in case of SPI the register
accesses are locked by means of the SPI bus mutex use a sleepable lock
(i.e. also a mutex) to ensure thread-safety of the counter which may be
accessed by both a userspace thread and the interrupt handler.
By doing this refactor the names of the amended functions to use a more
appropriate prefix.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Tested-by: Michael Niewöhner <linux@mniewoehner.de>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Stable-dep-of: 955df4f877 ("tpm, tpm_tis: Claim locality when interrupts are reenabled on resume")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15d7aa4e46 ]
In tpm_tis_probe_single_irq() interrupt registers TPM_INT_VECTOR,
TPM_INT_STATUS and TPM_INT_ENABLE are modified to setup the interrupts.
Currently these modifications are done without holding a locality thus they
have no effect. Fix this by claiming the (default) locality before the
registers are written.
Since now tpm_tis_gen_interrupt() is called with the locality already
claimed remove locality request and release from this function.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Stable-dep-of: 955df4f877 ("tpm, tpm_tis: Claim locality when interrupts are reenabled on resume")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d789ad726 ]
Both functions tpm_tis_probe_irq_single() and tpm_tis_probe_irq() may setup
the interrupts and then return with an error. This case is indicated by a
missing TPM_CHIP_FLAG_IRQ flag in chip->flags.
Currently the interrupt setup is only undone if tpm_tis_probe_irq_single()
fails. Undo the setup also if tpm_tis_probe_irq() fails.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Tested-by: Michael Niewöhner <linux@mniewoehner.de>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Stable-dep-of: 955df4f877 ("tpm, tpm_tis: Claim locality when interrupts are reenabled on resume")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 282657a8bd ]
In disable_interrupts() the TPM_GLOBAL_INT_ENABLE bit is unset in the
TPM_INT_ENABLE register to shut the interrupts off. However modifying the
register is only possible with a held locality. So claim the locality
before disable_interrupts() is called.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Tested-by: Michael Niewöhner <linux@mniewoehner.de>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Stable-dep-of: 955df4f877 ("tpm, tpm_tis: Claim locality when interrupts are reenabled on resume")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed9be0e6c8 ]
If in tpm_tis_probe_irq_single() an error occurs after the original
interrupt vector has been read, restore the interrupts before the error is
returned.
Since the caller does not check the error value, return -1 in any case that
the TPM_CHIP_FLAG_IRQ flag is not set. Since the return value of function
tpm_tis_gen_interrupt() is not longer used, make it a void function.
Fixes: 1107d065fd ("tpm_tis: Introduce intermediate layer for TPM access")
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ce1f694eb ]
The Makefile rule responsible for building flask.h and
av_permissions.h only lists flask.h as a target which means that
av_permissions.h is only generated when flask.h needs to be
generated. This patch fixes this by adding av_permissions.h as a
target to the rule.
Fixes: 8753f6bec3 ("selinux: generate flask headers during kernel build")
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bcab1adeaa ]
Make the flask.h target depend on the genheaders binary instead of
classmap.h to ensure that it is rebuilt if any of the dependencies of
genheaders are changed.
Notably this fixes flask.h not being rebuilt when
initial_sid_to_string.h is modified.
Fixes: 8753f6bec3 ("selinux: generate flask headers during kernel build")
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Acked-by: Stephen Smalley <stephen.smalley.work@gmail.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a2bdad0b4 ]
In preparation for reimplementing the do_vfp()->vfp_support_entry()
handover in C code, switch to using R3 to pass the 'success' return
address, rather than R9, as it cannot be used for parameter passing.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Stable-dep-of: c76c6c4ecb ("ARM: 9294/2: vfp: Fix broken softirq handling with instrumentation enabled")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dae904d96a ]
Instead of dereferencing thread_info in do_vfp, pass the thread_info
pointer to vfp_support_entry via R1. That way, we only use a single
caller save register, which makes it easier to convert do_vfp to C code
in a subsequent patch.
Note that, unlike the CPU number, which can change due to preemption,
passing the thread_info pointer can safely be done with preemption
enabled.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Stable-dep-of: c76c6c4ecb ("ARM: 9294/2: vfp: Fix broken softirq handling with instrumentation enabled")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa10366cc6 ]
resctrl_val() assumes ->setup() always returns either 0 to continue
tests or < 0 in case of the normal termination of tests after x runs.
The latter overlaps with normal error returns.
Define END_OF_TESTS (=1) to differentiate the normal termination of
tests and return errors as negative values. Alter callers of ->setup()
to handle errors properly.
Fixes: 790bf585b0 ("selftests/resctrl: Add Cache Allocation Technology (CAT) selftest")
Fixes: ecdbb911f2 ("selftests/resctrl: Add MBM test")
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c90b3b588e ]
resctrl_val() function is called only by MBM, MBA, and CMT tests which
means the else branch is never used.
Both test branches call param->setup().
Remove the unused else branch and place the ->setup() call outside of
the test specific branches reducing code duplication.
Co-developed-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Stable-dep-of: fa10366cc6 ("selftests/resctrl: Allow ->setup() to return errors")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 22a8be2803 ]
malloc_and_init_memory() in fill_buf isn't checking if memalign()
successfully allocated memory or not before accessing the memory.
Check the return value of memalign() and return NULL if allocating
aligned memory fails.
Fixes: a2561b12fe ("selftests/resctrl: Add built in benchmark")
Co-developed-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9a301c331 ]
Fix bug in debugfs logs that causes an incorrect order of lines in the
debugfs log.
Currently, the test counts lines that show the number of tests passed,
failed, and skipped, as well as any suite diagnostic lines,
appear prior to the individual results, which is a bug.
Ensure the order of printing for the debugfs log is correct. Additionally,
add a KTAP header to so the debugfs logs can be valid KTAP.
This is an example of a log prior to these fixes:
KTAP version 1
# Subtest: kunit_status
1..2
# kunit_status: pass:2 fail:0 skip:0 total:2
# Totals: pass:2 fail:0 skip:0 total:2
ok 1 kunit_status_set_failure_test
ok 2 kunit_status_mark_skipped_test
ok 1 kunit_status
Note the two lines with stats are out of order. This is the same debugfs
log after the fixes (in combination with the third patch to remove the
extra line):
KTAP version 1
1..1
KTAP version 1
# Subtest: kunit_status
1..2
ok 1 kunit_status_set_failure_test
ok 2 kunit_status_mark_skipped_test
# kunit_status: pass:2 fail:0 skip:0 total:2
# Totals: pass:2 fail:0 skip:0 total:2
ok 1 kunit_status
Signed-off-by: Rae Moar <rmoar@google.com>
Reviewed-by: David Gow <davidgow@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7455b7007b upstream.
Similar to commit 1c11289b34 ("peci: cpu: Fix use-after-free in
adev_release()"), the auxiliary device is not torn down in the correct
order. If auxiliary_device_add() fails, the release callback will be
called twice, resulting in a UAF. Due to timing, the auxdev code in this
driver "took inspiration" from the aforementioned commit, and thus its
bugs too!
Moving auxiliary_device_uninit() to the unregister callback instead
avoids the issue.
CC: stable@vger.kernel.org
Fixes: b56bae2dd6 ("clk: microchip: mpfs: add reset controller")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230413-critter-synopsis-dac070a86cb4@spud
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14705f969d upstream.
On my RTW8821CU chipset rfe_option reads as 0x22. Looking at the
vendor driver suggests that the field width of rfe_option is 5 bit,
so rfe_option should be masked with 0x1f.
Without this the rfe_option comparisons with 2 further down the
driver evaluate as false when they should really evaluate as true.
The effect is that 2G channels do not work.
rfe_option is also used as an array index into rtw8821c_rfe_defs[].
rtw8821c_rfe_defs[34] (0x22) was added as part of adding USB support,
likely because rfe_option reads as 0x22. As this now becomes 0x2,
rtw8821c_rfe_defs[34] is no longer used and can be removed.
Note that this might not be the whole truth. In the vendor driver
there are indeed places where the unmasked rfe_option value is used.
However, the driver has several places where rfe_option is tested
with the pattern if (rfe_option == 2 || rfe_option == 0x22) or
if (rfe_option == 4 || rfe_option == 0x24), so that rfe_option BIT(5)
has no influence on the code path taken. We therefore mask BIT(5)
out from rfe_option entirely until this assumption is proved wrong
by some chip variant we do not know yet.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Alexandru gagniuc <mr.nuke.me@gmail.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: ValdikSS <iam@valdikss.org.ru>
Cc: stable@vger.kernel.org
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230417140358.2240429-3-s.hauer@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d46e04ccd4 upstream.
Always run the entire init sequence (rtl8xxxu_init_device()) for
RTL8192EU. It's what the vendor driver does too.
This fixes a bug where the device is unable to connect after
rebooting:
wlp3s0f3u2: send auth to ... (try 1/3)
wlp3s0f3u2: send auth to ... (try 2/3)
wlp3s0f3u2: send auth to ... (try 3/3)
wlp3s0f3u2: authentication with ... timed out
Rebooting leaves the device powered on (partially? at least the
firmware is still running), but not really in a working state.
Cc: stable@vger.kernel.org
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Jes Sorensen <jes@trained-monkey.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/4eb111a9-d4c4-37d0-b376-4e202de7153c@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63cfd21003 upstream.
There are two pointers in struct xfrm_dev_offload, *dev, *real_dev.
The *dev points whether bonding interface or real interface, if
bonding IPsec offload is used, it points bonding interface; if not,
it points real interface. And *real_dev always points real interface.
So nfp should always use real_dev instead of dev.
Prior to this change the system becomes unresponsive when offloading
IPsec for a device which is a lower device to a bonding device.
Fixes: 859a497fe8 ("nfp: implement xfrm callbacks and expose ipsec offload feature to upper layer")
CC: stable@vger.kernel.org
Signed-off-by: Huanhuan Wang <huanhuan.wang@corigine.com>
Acked-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Link: https://lore.kernel.org/r/20230420140125.38521-1-louis.peens@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8dec88070d upstream.
Haibo Li reported:
| Unable to handle kernel paging request at virtual address
| ffffff802a0d8d7171
| Mem abort info⭕
| ESR = 0x9600002121
| EC = 0x25: DABT (current EL), IL = 32 bitsts
| SET = 0, FnV = 0 0
| EA = 0, S1PTW = 0 0
| FSC = 0x21: alignment fault
| Data abort info⭕
| ISV = 0, ISS = 0x0000002121
| CM = 0, WnR = 0 0
| swapper pgtable: 4k pages, 39-bit VAs, pgdp=000000002835200000
| [ffffff802a0d8d71] pgd=180000005fbf9003, p4d=180000005fbf9003,
| pud=180000005fbf9003, pmd=180000005fbe8003, pte=006800002a0d8707
| Internal error: Oops: 96000021 [#1] PREEMPT SMP
| Modules linked in:
| CPU: 2 PID: 45 Comm: kworker/u8:2 Not tainted
| 5.15.78-android13-8-g63561175bbda-dirty #1
| ...
| pc : kcsan_setup_watchpoint+0x26c/0x6bc
| lr : kcsan_setup_watchpoint+0x88/0x6bc
| sp : ffffffc00ab4b7f0
| x29: ffffffc00ab4b800 x28: ffffff80294fe588 x27: 0000000000000001
| x26: 0000000000000019 x25: 0000000000000001 x24: ffffff80294fdb80
| x23: 0000000000000000 x22: ffffffc00a70fb68 x21: ffffff802a0d8d71
| x20: 0000000000000002 x19: 0000000000000000 x18: ffffffc00a9bd060
| x17: 0000000000000001 x16: 0000000000000000 x15: ffffffc00a59f000
| x14: 0000000000000001 x13: 0000000000000000 x12: ffffffc00a70faa0
| x11: 00000000aaaaaaab x10: 0000000000000054 x9 : ffffffc00839adf8
| x8 : ffffffc009b4cf00 x7 : 0000000000000000 x6 : 0000000000000007
| x5 : 0000000000000000 x4 : 0000000000000000 x3 : ffffffc00a70fb70
| x2 : 0005ff802a0d8d71 x1 : 0000000000000000 x0 : 0000000000000000
| Call trace:
| kcsan_setup_watchpoint+0x26c/0x6bc
| __tsan_read2+0x1f0/0x234
| inflate_fast+0x498/0x750
| zlib_inflate+0x1304/0x2384
| __gunzip+0x3a0/0x45c
| gunzip+0x20/0x30
| unpack_to_rootfs+0x2a8/0x3fc
| do_populate_rootfs+0xe8/0x11c
| async_run_entry_fn+0x58/0x1bc
| process_one_work+0x3ec/0x738
| worker_thread+0x4c4/0x838
| kthread+0x20c/0x258
| ret_from_fork+0x10/0x20
| Code: b8bfc2a8 2a0803f7 14000007 d503249f (78bfc2a8) )
| ---[ end trace 613a943cb0a572b6 ]-----
The reason for this is that on certain arm64 configuration since
e35123d83e ("arm64: lto: Strengthen READ_ONCE() to acquire when
CONFIG_LTO=y"), READ_ONCE() may be promoted to a full atomic acquire
instruction which cannot be used on unaligned addresses.
Fix it by avoiding READ_ONCE() in read_instrumented_memory(), and simply
forcing the compiler to do the required access by casting to the
appropriate volatile type. In terms of generated code this currently
only affects architectures that do not use the default READ_ONCE()
implementation.
The only downside is that we are not guaranteed atomicity of the access
itself, although on most architectures a plain load up to machine word
size should still be atomic (a fact the default READ_ONCE() still relies
on itself).
Reported-by: Haibo Li <haibo.li@mediatek.com>
Tested-by: Haibo Li <haibo.li@mediatek.com>
Cc: <stable@vger.kernel.org> # 5.17+
Signed-off-by: Marco Elver <elver@google.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81c18e08a6 upstream.
If the unit address is appended to node name of memory-region,
then adding rproc carveouts fails as node name and unit-address
both are passed as carveout name (i.e. vdev0vring0@xxxxxxxx). However,
only node name is expected by remoteproc framework. This patch moves
memory-region node parsing from driver probe to prepare and
only passes node-name and not unit-address
Fixes: 6b291e8020 ("drivers: remoteproc: Add Xilinx r5 remoteproc driver")
Signed-off-by: Tanmay Shah <tanmay.shah@amd.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230311012407.1292118-5-tanmay.shah@amd.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e0489f6e22 upstream.
If mtd_otp_nvmem_add() fails, the partitions won't be removed
because there is simply no call to del_mtd_partitions().
Unfortunately, add_mtd_partitions() will print all partitions to
the kernel console. If mtd_otp_nvmem_add() returns -EPROBE_DEFER
this would print the partitions multiple times to the kernel
console. Instead move mtd_otp_nvmem_add() to the beginning of the
function.
Fixes: 4b361cfa86 ("mtd: core: add OTP nvmem provider support")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230308082021.870459-3-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1cd9ceaa52 upstream.
Commit c048b60d39 ("mtd: core: provide unique name for nvmem device")
tries to give the nvmem device a unique name, but fails badly if the mtd
device doesn't have a "struct device" associated with it, i.e. if
CONFIG_MTD_PARTITIONED_MASTER is not set. This will result in the name
"(null)-user-otp", which is not unique. It seems the best we can do is
to use the compatible name together with a unique identifier added by
the nvmem subsystem by using NVMEM_DEVID_AUTO.
Fixes: c048b60d39 ("mtd: core: provide unique name for nvmem device")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230308082021.870459-1-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc05e06e60 upstream.
Commit 7e55c60acf ("md/raid5: Pivot raid5_make_request()") changed the
order in which requests for underlying disks are created. Since for
large sequential IO adding of requests frequently races with md_raid5
thread submitting bios to underlying disks, this results in a change in
IO pattern because intermediate states of new order of request creation
result in more smaller discontiguous requests. For RAID5 on top of three
rotational disks our performance testing revealed this results in
regression in write throughput:
iozone -a -s 131072000 -y 4 -q 8 -i 0 -i 1 -R
before 7e55c60acf:
KB reclen write rewrite read reread
131072000 4 493670 525964 524575 513384
131072000 8 540467 532880 512028 513703
after 7e55c60acf:
KB reclen write rewrite read reread
131072000 4 421785 456184 531278 509248
131072000 8 459283 456354 528449 543834
To reduce the amount of discontiguous requests we can start generating
requests with the stripe with the lowest chunk offset as that has the
best chance of being adjacent to IO queued previously. This improves the
performance to:
KB reclen write rewrite read reread
131072000 4 497682 506317 518043 514559
131072000 8 514048 501886 506453 504319
restoring big part of the regression.
Fixes: 7e55c60acf ("md/raid5: Pivot raid5_make_request()")
Cc: stable@vger.kernel.org # v6.0+
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230417171537.17899-1-jack@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a405c6f022 upstream.
init_resync() inits mempool and sets conf->have_replacemnt at the beginning
of sync, close_sync() frees the mempool when sync is completed.
After [1] recovery might be skipped and init_resync() is called but
close_sync() is not. null-ptr-deref occurs with r10bio->dev[i].repl_bio.
The following is one way to reproduce the issue.
1) create a array, wait for resync to complete, mddev->recovery_cp is set
to MaxSector.
2) recovery is woken and it is skipped. conf->have_replacement is set to
0 in init_resync(). close_sync() not called.
3) some io errors and rdev A is set to WantReplacement.
4) a new device is added and set to A's replacement.
5) recovery is woken, A have replacement, but conf->have_replacemnt is
0. r10bio->dev[i].repl_bio will not be alloced and null-ptr-deref
occurs.
Fix it by not calling init_resync() if recovery skipped.
[1] commit 7e83ccbecd ("md/raid10: Allow skipping recovery when clean arrays are assembled")
Fixes: 7e83ccbecd ("md/raid10: Allow skipping recovery when clean arrays are assembled")
Cc: stable@vger.kernel.org
Signed-off-by: Li Nan <linan122@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230222041000.3341651-3-linan666@huaweicloud.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3899d94e38 upstream.
When we receive a flush command (or "barrier" in DRBD), we currently use
a REQ_OP_FLUSH with the REQ_PREFLUSH flag set.
The correct way to submit a flush bio is by using a REQ_OP_WRITE without
any data, and set the REQ_PREFLUSH flag.
Since commit b4a6bb3a67 ("block: add a sanity check for non-write
flush/fua bios"), this triggers a warning in the block layer, but this
has been broken for quite some time before that.
So use the correct set of flags to actually make the flush happen.
Cc: Christoph Hellwig <hch@infradead.org>
Cc: stable@vger.kernel.org
Fixes: f9ff0da564 ("drbd: allow parallel flushes for multi-volume resources")
Reported-by: Thomas Voegtle <tv@lio96.de>
Signed-off-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230503121937.17232-1-christoph.boehmwalder@linbit.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28a65b49eb upstream.
According to syzbot's report, mark_buffer_dirty() called from
nilfs_segctor_do_construct() outputs a warning with some patterns after
nilfs2 detects metadata corruption and degrades to read-only mode.
After such read-only degeneration, page cache data may be cleared through
nilfs_clear_dirty_page() which may also clear the uptodate flag for their
buffer heads. However, even after the degeneration, log writes are still
performed by unmount processing etc., which causes mark_buffer_dirty() to
be called for buffer heads without the "uptodate" flag and causes the
warning.
Since any writes should not be done to a read-only file system in the
first place, this fixes the warning in mark_buffer_dirty() by letting
nilfs_segctor_do_construct() abort early if in read-only mode.
This also changes the retry check of nilfs_segctor_write_out() to avoid
unnecessary log write retries if it detects -EROFS that
nilfs_segctor_do_construct() returned.
Link: https://lkml.kernel.org/r/20230427011526.13457-1-konishi.ryusuke@gmail.com
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Reported-by: syzbot+2af3bc9585be7f23f290@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=2af3bc9585be7f23f290
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84822215ac upstream.
The WCD938x comes with three devices on two Linux drivers:
1. RX Soundwire device (wcd938x-sdw.c driver),
2. TX Soundwire device, which is used to access devices via regmap (also
wcd938x-sdw.c driver),
3. platform device (wcd938x.c driver) - glue and component master,
actually having most of the code using TX Soundwire device regmap.
When RX and TX Soundwire devices probe, the component master (platform
device) bind tries to write micbias configuration via TX Soundwire
regmap. This might happen before TX Soundwire enumerates, so the regmap
access fails. On Qualcomm SM8550 board with WCD9385:
qcom-soundwire 6d30000.soundwire-controller: Qualcomm Soundwire controller v2.0.0 Registered
wcd938x_codec audio-codec: bound sdw:0:0217:010d:00:4 (ops wcd938x_sdw_component_ops)
wcd938x_codec audio-codec: bound sdw:0:0217:010d:00:3 (ops wcd938x_sdw_component_ops)
qcom-soundwire 6ad0000.soundwire-controller: swrm_wait_for_wr_fifo_avail err write overflow
Fix the issue by:
1. Moving the regmap creation from platform device to TX Soundwire
device. The regmap settings are moved as-is with one difference:
making the wcd938x_regmap_config const.
2. Using regmap in cache only mode till the actual TX Soundwire device
enumerates and then sync the regmap cache.
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Message-Id: <20230503144102.242240-1-krzysztof.kozlowski@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7477cb976 upstream.
This patch adds support for the mute LED on the HP Pavilion Aero Laptop
13-be0xxx. The current behavior is that the LED does not turn on at any
time and does not indicate to the user whether the sound is muted.
The solution is to add a PCI quirk to properly recognize and support the
LED on this device.
This change has been tested on the device in question using modified
versions of kernels 6.0.7-6.2.12 on Arch Linux.
Signed-off-by: Caleb Harper <calebharp2005@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230503175026.6796-1-calebharp2005@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d755bd2cae upstream.
Matthew Wilcox noticed, that if ARCH_HAS_FLUSH_ON_KUNMAP is defined
(which is the case for PA-RISC), __kunmap_local() calls
kunmap_flush_on_unmap(), which may call the parisc flush functions with
a non-page-aligned address and thus the page might not be fully flushed.
This patch ensures that flush_kernel_dcache_page_asm() and
flush_kernel_dcache_page_asm() will always operate on page-aligned
addresses.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org> # v6.0+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e3220ba33 upstream.
Fix the argument pointer (ap) to point to real-mode memory
instead of virtual memory.
It's interesting that this issue hasn't shown up earlier, as this could
have happened with any 64-bit PDC ROM code.
I just noticed it because I suddenly faced a HPMC while trying to execute
the 64-bit STI ROM code of an Visualize-FXe graphics card for the STI
text console.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d1493bdc2 upstream.
If firmware loading fails, the controller's pm_state is updated to
MHI_PM_FW_DL_ERR unconditionally. This can corrupt the pm_state as the
update is not done under the proper lock, and also does not validate
the state transition. The firmware loading can fail due to a detected
syserr, but if MHI_PM_FW_DL_ERR is unconditionally set as the pm_state,
the handling of the syserr can break when it attempts to transition from
syserr detect, to syserr process.
By grabbing the lock, we ensure we don't race with some other pm_state
update. By using mhi_try_set_pm_state(), we check that the transition
to MHI_PM_FW_DL_ERR is valid via the state machine logic. If it is not
valid, then some other transition is occurring like syserr processing, and
we assume that will resolve the firmware loading error.
Fixes: 12e050c77b ("bus: mhi: core: Move to an error state on any firmware load failure")
Cc: stable@vger.kernel.org
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Carl Vanderlip <quic_carlv@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://lore.kernel.org/r/1681142292-27571-3-git-send-email-quic_jhugo@quicinc.com
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d469d9448a upstream.
If we detect a system error via intvec, we only process the syserr if the
current ee is different than the last observed ee. The reason for this
check is to prevent bhie from running multiple times, but with the single
queue handling syserr, that is not possible.
The check can cause an issue with device recovery. If PBL loads a bad SBL
via BHI, but that SBL hangs before notifying the host of an ee change,
then issuing soc_reset to crash the device and retry (after supplying a
fixed SBL) will not recover the device as the host will observe a PBL->PBL
transition and not process the syserr. The device will be stuck until
either the driver is reloaded, or the host is rebooted. Instead, remove
the check so that we can attempt to recover the device.
Fixes: ef2126c4e2 ("bus: mhi: core: Process execution environment changes serially")
Cc: stable@vger.kernel.org
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Carl Vanderlip <quic_carlv@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://lore.kernel.org/r/1681142292-27571-2-git-send-email-quic_jhugo@quicinc.com
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1423885c84 upstream.
The CXL specification mandates that 4-byte registers must be accessed
with 4-byte access cycles. CXL 3.0 8.2.3 "Component Register Layout and
Definition" states that the behavior is undefined if (2) 32-bit
registers are accessed as an 8-byte quantity. It turns out that at least
one hardware implementation is sensitive to this in practice. The @size
variable results in zero with:
size = readq(hdm + CXL_HDM_DECODER0_SIZE_LOW_OFFSET(which));
...and the correct size with:
lo = readl(hdm + CXL_HDM_DECODER0_SIZE_LOW_OFFSET(which));
hi = readl(hdm + CXL_HDM_DECODER0_SIZE_HIGH_OFFSET(which));
size = (hi << 32) + lo;
Fixes: d17d0540a0 ("cxl/core/hdm: Add CXL standard decoder enumeration to the core")
Cc: <stable@vger.kernel.org>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Alison Schofield <alison.schofield@intel.com>
Link: https://lore.kernel.org/r/168149844056.792294.8224490474529733736.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa88019851 upstream.
In commit fe08cc5044 we reworked the valid superblock version
checks. If it is a V5 filesystem, it is always valid, then we
checked if the version was less than V4 (reject) and then checked
feature fields in the V4 flags to determine if it was valid.
What we missed was that if the version is not V4 at this point,
we shoudl reject the fs. i.e. the check current treats V6+
filesystems as if it was a v4 filesystem. Fix this.
cc: stable@vger.kernel.org
Fixes: fe08cc5044 ("xfs: open code sb verifier feature checks")
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a034c1370d upstream.
This patch introduce a new internal flag per lkb value to handle
internal flags which are handled not on wire. The current lkb internal
flags stored as lkb->lkb_flags are split in upper and lower bits, the
lower bits are used to share internal flags over wire for other cluster
wide lkb copies on other nodes.
In commit 61bed0baa4 ("fs: dlm: use a non-static queue for callbacks")
we introduced a new internal flag for pending callbacks for the dlm
callback queue. This flag is protected by the lkb->lkb_cb_lock lock.
This patch overlooked that on dlm receive path and the mentioned upper
and lower bits, that dlm will read the flags, mask it and write it
back. As example receive_flags() in fs/dlm/lock.c. This flag
manipulation is not done atomically and is not protected by
lkb->lkb_cb_lock. This has unknown side effects of the current callback
handling.
In future we should move to set/clear/test bit functionality and avoid
read, mask and writing back flag values. In later patches we will move
the upper parts to the new introduced internal lkb flags which are not
shared between other cluster nodes to the new non shared internal flag
field to avoid similar issues.
Cc: stable@vger.kernel.org
Fixes: 61bed0baa4 ("fs: dlm: use a non-static queue for callbacks")
Reported-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aaf67de788 upstream.
When trimming the caps and just after the 'session->s_cap_lock' is
released in ceph_iterate_session_caps() the cap maybe removed by
another thread, and when using the stale cap memory in the callbacks
it will trigger use-after-free crash.
We need to check the existence of the cap just after the 'ci->i_ceph_lock'
being acquired. And do nothing if it's already removed.
Cc: stable@vger.kernel.org
Link: https://tracker.ceph.com/issues/43272
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Luís Henriques <lhenriques@suse.de>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a36d20e01 upstream.
If renaming a file in an encrypted directory, function
fscrypt_setup_filename allocates memory for a file name. This name is
never used, and before returning to the caller the memory for it is not
freed.
When running kmemleak on it we see that it is registered as a leak. The
report below is triggered by a simple program 'rename' that renames a
file in an encrypted directory:
unreferenced object 0xffff888101502840 (size 32):
comm "rename", pid 9404, jiffies 4302582475 (age 435.735s)
backtrace:
__kmem_cache_alloc_node
__kmalloc
fscrypt_setup_filename
do_rename
ubifs_rename
vfs_rename
do_renameat2
To fix this we can remove the call to fscrypt_setup_filename as it's not
needed.
Fixes: 278d9a2436 ("ubifs: Rename whiteout atomically")
Reported-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1fb815b38b upstream.
When opening a ubifs tmpfile on an encrypted directory, function
fscrypt_setup_filename allocates memory for the name that is to be
stored in the directory entry, but after the name has been copied to the
directory entry inode, the memory is not freed.
When running kmemleak on it we see that it is registered as a leak. The
report below is triggered by a simple program 'tmpfile' just opening a
tmpfile:
unreferenced object 0xffff88810178f380 (size 32):
comm "tmpfile", pid 509, jiffies 4294934744 (age 1524.742s)
backtrace:
__kmem_cache_alloc_node
__kmalloc
fscrypt_setup_filename
ubifs_tmpfile
vfs_tmpfile
path_openat
Free this memory after it has been copied to the inode.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31a149d5c1 upstream.
The commit 2d78aee426 ("UBI: simplify LEB write and atomic LEB change code")
adds helper function, try_write_vid_and_data(), to simplify the code, but this
helper function has bug, it will return 0 (success) when ubi_io_write_vid_hdr()
or the ubi_io_write_data() return error number (-EIO, etc), because the return
value of ubi_wl_put_peb() will overwrite the original return value.
This issue will cause unexpected data loss issue, because the caller of this
function and UBIFS willn't know the data is lost.
Fixes: 2d78aee426 ("UBI: simplify LEB write and atomic LEB change code")
Cc: stable@vger.kernel.org
Signed-off-by: Wang YanQing <udknight@gmail.com>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5fda08ef2 upstream.
Following process will cause a memleak for copied up znode:
dirty_cow_znode
zn = copy_znode(c, znode);
err = insert_old_idx(c, zbr->lnum, zbr->offs);
if (unlikely(err))
return ERR_PTR(err); // No one refers to zn.
Fetch a reproducer in [Link].
Function copy_znode() is split into 2 parts: resource allocation
and znode replacement, insert_old_idx() is split in similar way,
so resource cleanup could be done in error handling path without
corrupting metadata(mem & disk).
It's okay that old index inserting is put behind of add_idx_dirt(),
old index is used in layout_leb_in_gaps(), so the two processes do
not depend on each other.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216705
Fixes: 1e51764a3c ("UBIFS: add new flash file system")
Cc: stable@vger.kernel.org
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d01cb27f6 upstream.
This reverts commit 122deabfe1 (ubifs: dirty_cow_znode: Fix memleak
in error handling path).
After commit 122deabfe1 applied, if insert_old_idx() failed, old
index neither exists in TNC nor in old-index tree. Which means that
old index node could be overwritten in layout_leb_in_gaps(), then
ubifs image will be corrupted in power-cut.
Fixes: 122deabfe1 (ubifs: dirty_cow_znode: Fix memleak ... path)
Cc: stable@vger.kernel.org
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ccc62b8277 upstream.
commit b9c6ff94e4 ("iommu/amd: Re-factor guest virtual APIC
(de-)activation code") while refactoring guest virtual APIC
activation/de-activation code, stored information for activate/de-activate
in "struct amd_ir_data". It used 32-bit integer data type for storing the
"Guest Virtual APIC Table Root Pointer" (ga_root_ptr), though the
"ga_root_ptr" is actually a 40-bit field in IRTE (Interrupt Remapping
Table Entry).
This causes interrupts from PCIe devices to not reach the guest in the case
of PCIe passthrough with SME (Secure Memory Encryption) enabled as _SME_
bit in the "ga_root_ptr" is lost before writing it to the IRTE.
Fix it by using 64-bit data type for storing the "ga_root_ptr". While at
that also change the data type of "ga_tag" to u32 in order to match
the IOMMU spec.
Fixes: b9c6ff94e4 ("iommu/amd: Re-factor guest virtual APIC (de-)activation code")
Cc: stable@vger.kernel.org # v5.4+
Reported-by: Alejandro Jimenez <alejandro.j.jimenez@oracle.com>
Reviewed-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Kishon Vijay Abraham I <kvijayab@amd.com>
Link: https://lore.kernel.org/r/20230405130317.9351-1-kvijayab@amd.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5d68f84f4 upstream.
If cur_state for the powerclamp cooling device is set to the default
minimum state of 0, without setting first to cur_state > 0, this results
in NULL pointer access.
This NULL pointer access happens in the powercap core idle-inject
function idle_inject_set_duration() as there is no NULL check for
idle_inject_device pointer. This pointer must be allocated by calling
idle_inject_register() or idle_inject_register_full().
In the function powerclamp_set_cur_state(), idle_inject_device pointer
is allocated only when the cur_state > 0. But setting 0 without changing
to any other state, idle_inject_set_duration() will be called with a
NULL idle_inject_device pointer.
To address this, just return from powerclamp_set_cur_state() if the
current cooling device state is the same as the last one. Since the
power-up default cooling device state is 0, changing the state to 0
again here will return without calling idle_inject_set_duration().
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Fixes: 8526eb7fc7 ("thermal: intel: powerclamp: Use powercap idle-inject feature")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=217386
Tested-by: Risto A. Paju <teknohog@iki.fi>
Cc: 6.3+ <stable@kernel.org> # 6.3+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c770657bd2 upstream.
Using standard mode, rare false ACK responses were appearing with
i2cdetect tool. This was happening due to NACK interrupt triggering
ISR thread before register access interrupt was ready. Removing the
NACK interrupt's ability to trigger ISR thread lets register access
ready interrupt do this instead.
Cc: <stable@vger.kernel.org> # v3.7+
Fixes: 3b2f8f82da ("i2c: omap: switch to threaded IRQ support")
Signed-off-by: Reid Tonking <reidt@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ce29c17dc upstream.
igc_configure_rx_ring() function will be called as part of XDP program
setup. If Rx hardware timestamp is enabled prio to XDP program setup,
this timestamp enablement will be overwritten when buffer size is
written into SRRCTL register.
Thus, this commit read the register value before write to SRRCTL
register. This commit is tested by using xdp_hw_metadata bpf selftest
tool. The tool enables Rx hardware timestamp and then attach XDP program
to igc driver. It will display hardware timestamp of UDP packet with
port number 9092. Below are detail of test steps and results.
Command on DUT:
sudo ./xdp_hw_metadata <interface name>
Command on Link Partner:
echo -n skb | nc -u -q1 <destination IPv4 addr> 9092
Result before this patch:
skb hwtstamp is not found!
Result after this patch:
found skb hwtstamp = 1677800973.642836757
Optionally, read PHC to confirm the values obtained are almost the same:
Command:
sudo ./testptp -d /dev/ptp0 -g
Result:
clock time: 1677800973.913598978 or Fri Mar 3 07:49:33 2023
Fixes: fc9df2a0b5 ("igc: Enable RX via AF_XDP zero-copy")
Cc: <stable@vger.kernel.org> # 5.14+
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3db66620ea upstream.
Remove the acpi_backlight=video quirk for Lenovo ThinkPad W530.
This was intended to help users of the (unsupported) Nvidia binary driver,
but this has been reported to cause backlight control issues for users
who have the gfx configured in hybrid (dual-GPU) mode, so drop this.
The Nvidia binary driver should call acpi_video_register_backlight()
when necessary and this has been reported to Nvidia.
Until this is fixed Nvidia binary driver users can work around this by
passing "acpi_backlight=video" on the kernel commandline (with the latest
6.1.y or newer stable series, kernels < 6.1.y don't need this).
Fixes: a5b2781dca ("ACPI: video: Add acpi_backlight=video quirk for Lenovo ThinkPad W530")
Reported-by: Русев Путин <rockeraliexpress@gmail.com>
Link: https://lore.kernel.org/linux-acpi/CAK4BXn0ngZRmzx1bodAF8nmYj0PWdUXzPGHofRrsyZj8MBpcVA@mail.gmail.com/
Cc: 6.1+ <stable@vger.kernel.org> # 6.1+
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit abcc506a9a upstream.
When smb client send concurrent smb2 close and logoff request
with multichannel connection, It can cause racy issue. logoff request
free tcon and can cause UAF issues in smb2 close. When receiving logoff
request with multichannel, ksmbd should wait until all remaning requests
complete as well as ones in the current connection, and then make
session expired.
Cc: stable@vger.kernel.org
Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-20796 ZDI-CAN-20595
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea174a9189 upstream.
client can indefinitely send smb2 session setup requests with
the SessionId set to 0, thus indefinitely spawning new sessions,
and causing indefinite memory usage. This patch limit to the number
of sessions using expired timeout and session state.
Cc: stable@vger.kernel.org
Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-20478
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b096d97f47 upstream.
ksmbd make a delay of 5 seconds on session setup to avoid dictionary
attacks. But the 5 seconds delay can be bypassed by using asynchronous
requests. This patch block all requests on current connection when
making a delay on sesstion setup failure.
Cc: stable@vger.kernel.org
Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-20482
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f5c779b7dd upstream.
This racy issue is triggered by sending concurrent session setup and
logoff requests. This patch does not set connection status as
KSMBD_SESS_GOOD if state is KSMBD_SESS_NEED_RECONNECT in session setup.
And relookup session to validate if session is deleted in logoff.
Cc: stable@vger.kernel.org
Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-20481, ZDI-CAN-20590, ZDI-CAN-20596
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b4323373d upstream.
Deadlock is triggered by sending multiple concurrent session setup
requests. It should be reused after releasing when getting ctx for crypto.
Multiple consecutive ctx uses cause deadlock while waiting for releasing
due to the limited number of ctx.
Cc: stable@vger.kernel.org
Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-20591
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d7cb549c2 upstream.
If client send session setup request with unknown NTLMSSP message type,
session that does not included channel can be created. It will cause
session memleak. because ksmbd_sessions_deregister() does not destroy
session if channel is not included. This patch return error response if
client send the request unknown NTLMSSP message type.
Cc: stable@vger.kernel.org
Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-20593
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eb307d09fe upstream.
racy issue is triggered the bug by racing between closing a connection
and rmmod. In ksmbd, rcu_barrier() is not called at module unload time,
so nothing prevents ksmbd from getting unloaded while it still has RCU
callbacks pending. It leads to trigger unintended execution of kernel
code locally and use to defeat protections such as Kernel Lockdown
Cc: stable@vger.kernel.org
Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-20477
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit edbdb43fc9 upstream.
Preserve TDP MMU roots until they are explicitly invalidated by gifting
the TDP MMU itself a reference to a root when it is allocated. Keeping a
reference in the TDP MMU fixes a flaw where the TDP MMU exhibits terrible
performance, and can potentially even soft-hang a vCPU, if a vCPU
frequently unloads its roots, e.g. when KVM is emulating SMI+RSM.
When KVM emulates something that invalidates _all_ TLB entries, e.g. SMI
and RSM, KVM unloads all of the vCPUs roots (KVM keeps a small per-vCPU
cache of previous roots). Unloading roots is a simple way to ensure KVM
flushes and synchronizes all roots for the vCPU, as KVM flushes and syncs
when allocating a "new" root (from the vCPU's perspective).
In the shadow MMU, KVM keeps track of all shadow pages, roots included, in
a per-VM hash table. Unloading a shadow MMU root just wipes it from the
per-vCPU cache; the root is still tracked in the per-VM hash table. When
KVM loads a "new" root for the vCPU, KVM will find the old, unloaded root
in the per-VM hash table.
Unlike the shadow MMU, the TDP MMU doesn't track "inactive" roots in a
per-VM structure, where "active" in this case means a root is either
in-use or cached as a previous root by at least one vCPU. When a TDP MMU
root becomes inactive, i.e. the last vCPU reference to the root is put,
KVM immediately frees the root (asterisk on "immediately" as the actual
freeing may be done by a worker, but for all intents and purposes the root
is gone).
The TDP MMU behavior is especially problematic for 1-vCPU setups, as
unloading all roots effectively frees all roots. The issue is mitigated
to some degree in multi-vCPU setups as a different vCPU usually holds a
reference to an unloaded root and thus keeps the root alive, allowing the
vCPU to reuse its old root after unloading (with a flush+sync).
The TDP MMU flaw has been known for some time, as until very recently,
KVM's handling of CR0.WP also triggered unloading of all roots. The
CR0.WP toggling scenario was eventually addressed by not unloading roots
when _only_ CR0.WP is toggled, but such an approach doesn't Just Work
for emulating SMM as KVM must emulate a full TLB flush on entry and exit
to/from SMM. Given that the shadow MMU plays nice with unloading roots
at will, teaching the TDP MMU to do the same is far less complex than
modifying KVM to track which roots need to be flushed before reuse.
Note, preserving all possible TDP MMU roots is not a concern with respect
to memory consumption. Now that the role for direct MMUs doesn't include
information about the guest, e.g. CR0.PG, CR0.WP, CR4.SMEP, etc., there
are _at most_ six possible roots (where "guest_mode" here means L2):
1. 4-level !SMM !guest_mode
2. 4-level SMM !guest_mode
3. 5-level !SMM !guest_mode
4. 5-level SMM !guest_mode
5. 4-level !SMM guest_mode
6. 5-level !SMM guest_mode
And because each vCPU can track 4 valid roots, a VM can already have all
6 root combinations live at any given time. Not to mention that, in
practice, no sane VMM will advertise different guest.MAXPHYADDR values
across vCPUs, i.e. KVM won't ever use both 4-level and 5-level roots for
a single VM. Furthermore, the vast majority of modern hypervisors will
utilize EPT/NPT when available, thus the guest_mode=%true cases are also
unlikely to be utilized.
Reported-by: Jeremi Piotrowski <jpiotrowski@linux.microsoft.com>
Link: https://lore.kernel.org/all/959c5bce-beb5-b463-7158-33fc4a4f910c@linux.microsoft.com
Link: https://lkml.kernel.org/r/20220209170020.1775368-1-pbonzini%40redhat.com
Link: https://lore.kernel.org/all/20230322013731.102955-1-minipli@grsecurity.net
Link: https://lore.kernel.org/all/000000000000a0bc2b05f9dd7fab@google.com
Link: https://lore.kernel.org/all/000000000000eca0b905fa0f7756@google.com
Cc: Ben Gardon <bgardon@google.com>
Cc: David Matlack <dmatlack@google.com>
Cc: stable@vger.kernel.org
Tested-by: Jeremi Piotrowski <jpiotrowski@linux.microsoft.com>
Link: https://lore.kernel.org/r/20230426220323.3079789-1-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2ed90cb093 upstream.
Read mmu_invalidate_seq before dropping the mmap_lock so that KVM can
detect if the results of vma_lookup() (e.g. vma_shift) become stale
before it acquires kvm->mmu_lock. This fixes a theoretical bug where a
VMA could be changed by userspace after vma_lookup() and before KVM
reads the mmu_invalidate_seq, causing KVM to install page table entries
based on a (possibly) no-longer-valid vma_shift.
Re-order the MMU cache top-up to earlier in user_mem_abort() so that it
is not done after KVM has read mmu_invalidate_seq (i.e. so as to avoid
inducing spurious fault retries).
It's unlikely that any sane userspace currently modifies VMAs in such a
way as to trigger this race. And even with directed testing I was unable
to reproduce it. But a sufficiently motivated host userspace might be
able to exploit this race.
Note KVM/ARM had the same bug and was fixed in a separate, near
identical patch (see Link).
Link: https://lore.kernel.org/kvm/20230313235454.2964067-1-dmatlack@google.com/
Fixes: 9955371cc0 ("RISC-V: KVM: Implement MMU notifiers")
Cc: stable@vger.kernel.org
Signed-off-by: David Matlack <dmatlack@google.com>
Tested-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 43ec16f145 upstream.
There is a crash in relay_file_read, as the var from
point to the end of last subbuf.
The oops looks something like:
pc : __arch_copy_to_user+0x180/0x310
lr : relay_file_read+0x20c/0x2c8
Call trace:
__arch_copy_to_user+0x180/0x310
full_proxy_read+0x68/0x98
vfs_read+0xb0/0x1d0
ksys_read+0x6c/0xf0
__arm64_sys_read+0x20/0x28
el0_svc_common.constprop.3+0x84/0x108
do_el0_svc+0x74/0x90
el0_svc+0x1c/0x28
el0_sync_handler+0x88/0xb0
el0_sync+0x148/0x180
We get the condition by analyzing the vmcore:
1). The last produced byte and last consumed byte
both at the end of the last subbuf
2). A softirq calls function(e.g __blk_add_trace)
to write relay buffer occurs when an program is calling
relay_file_read_avail().
relay_file_read
relay_file_read_avail
relay_file_read_consume(buf, 0, 0);
//interrupted by softirq who will write subbuf
....
return 1;
//read_start point to the end of the last subbuf
read_start = relay_file_read_start_pos
//avail is equal to subsize
avail = relay_file_read_subbuf_avail
//from points to an invalid memory address
from = buf->start + read_start
//system is crashed
copy_to_user(buffer, from, avail)
Link: https://lkml.kernel.org/r/20230419040203.37676-1-zhang.zhengming@h3c.com
Fixes: 8d62fdebda ("relay file read: start-pos fix")
Signed-off-by: Zhang Zhengming <zhang.zhengming@h3c.com>
Reviewed-by: Zhao Lei <zhao_lei1@hoperun.com>
Reviewed-by: Zhou Kete <zhou.kete@h3c.com>
Reviewed-by: Pengcheng Yang <yangpc@wangsu.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 49e5d16b6f upstream.
commit f003277311 ("KVM: arm64: Use config_lock to protect vgic
state") was meant to rectify a longstanding lock ordering issue in KVM
where the kvm->lock is taken while holding vcpu->mutex. As it so
happens, the aforementioned commit introduced yet another locking issue
by acquiring the its_lock before acquiring the config lock.
This is obviously wrong, especially considering that the lock ordering
is well documented in vgic.c. Reshuffle the locks once more to take the
config_lock before the its_lock. While at it, sprinkle in the lockdep
hinting that has become popular as of late to keep lockdep apprised of
our ordering.
Cc: stable@vger.kernel.org
Fixes: f003277311 ("KVM: arm64: Use config_lock to protect vgic state")
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230412062733.988229-1-oliver.upton@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f003277311 upstream.
Almost all of the vgic state is VM-scoped but accessed from the context
of a vCPU. These accesses were serialized on the kvm->lock which cannot
be nested within a vcpu->mutex critical section.
Move over the vgic state to using the config_lock. Tweak the lock
ordering where necessary to ensure that the config_lock is acquired
after the vcpu->mutex. Acquire the config_lock in kvm_vgic_create() to
avoid a race between the converted flows and GIC creation. Where
necessary, continue to acquire kvm->lock to avoid a race with vCPU
creation (i.e. flows that use lock_all_vcpus()).
Finally, promote the locking expectations in comments to lockdep
assertions and update the locking documentation for the config_lock as
well as vcpu->mutex.
Cc: stable@vger.kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230327164747.2466958-5-oliver.upton@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4bba7f7def upstream.
There are various bits of VM-scoped data that can only be configured
before the first call to KVM_RUN, such as the hypercall bitmaps and
the PMU. As these fields are protected by the kvm->lock and accessed
while holding vcpu->mutex, this is yet another example of lock
inversion.
Change out the kvm->lock for kvm->arch.config_lock in all of these
instances. Opportunistically simplify the locking mechanics of the
PMU configuration by holding the config_lock for the entirety of
kvm_arm_pmu_v3_set_attr().
Note that this also addresses a couple of bugs. There is an unguarded
read of the PMU version in KVM_ARM_VCPU_PMU_V3_FILTER which could race
with KVM_ARM_VCPU_PMU_V3_SET_PMU. Additionally, until now writes to the
per-vCPU vPMU irq were not serialized VM-wide, meaning concurrent calls
to KVM_ARM_VCPU_PMU_V3_IRQ could lead to a false positive in
pmu_irq_is_valid().
Cc: stable@vger.kernel.org
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230327164747.2466958-4-oliver.upton@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c43120afb5 upstream.
kvm->lock must be taken outside of the vcpu->mutex. Of course, the
locking documentation for KVM makes this abundantly clear. Nonetheless,
the locking order in KVM/arm64 has been wrong for quite a while; we
acquire the kvm->lock while holding the vcpu->mutex all over the shop.
All was seemingly fine until commit 42a90008f8 ("KVM: Ensure lockdep
knows about kvm->lock vs. vcpu->mutex ordering rule") caught us with our
pants down, leading to lockdep barfing:
======================================================
WARNING: possible circular locking dependency detected
6.2.0-rc7+ #19 Not tainted
------------------------------------------------------
qemu-system-aar/859 is trying to acquire lock:
ffff5aa69269eba0 (&host_kvm->lock){+.+.}-{3:3}, at: kvm_reset_vcpu+0x34/0x274
but task is already holding lock:
ffff5aa68768c0b8 (&vcpu->mutex){+.+.}-{3:3}, at: kvm_vcpu_ioctl+0x8c/0xba0
which lock already depends on the new lock.
Add a dedicated lock to serialize writes to VM-scoped configuration from
the context of a vCPU. Protect the register width flags with the new
lock, thus avoiding the need to grab the kvm->lock while holding
vcpu->mutex in kvm_reset_vcpu().
Cc: stable@vger.kernel.org
Reported-by: Jeremy Linton <jeremy.linton@arm.com>
Link: https://lore.kernel.org/kvmarm/f6452cdd-65ff-34b8-bab0-5c06416da5f6@arm.com/
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230327164747.2466958-3-oliver.upton@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0acc7239c2 upstream.
KVM/arm64 had the lock ordering backwards on vcpu->mutex and kvm->lock
from the very beginning. One such example is the way vCPU resets are
handled: the kvm->lock is acquired while handling a guest CPU_ON PSCI
call.
Add a dedicated lock to serialize writes to kvm_vcpu_arch::{mp_state,
reset_state}. Promote all accessors of mp_state to {READ,WRITE}_ONCE()
as readers do not acquire the mp_state_lock. While at it, plug yet
another race by taking the mp_state_lock in the KVM_SET_MP_STATE ioctl
handler.
As changes to MP state are now guarded with a dedicated lock, drop the
kvm->lock acquisition from the PSCI CPU_ON path. Similarly, move the
reader of reset_state outside of the kvm->lock and instead protect it
with the mp_state_lock. Note that writes to reset_state::reset have been
demoted to regular stores as both readers and writers acquire the
mp_state_lock.
While the kvm->lock inversion still exists in kvm_reset_vcpu(), at least
now PSCI CPU_ON no longer depends on it for serializing vCPU reset.
Cc: stable@vger.kernel.org
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230327164747.2466958-2-oliver.upton@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4984563823 upstream.
Extend VMX's nested intercept logic for emulated instructions to handle
"pause" interception, in quotes because KVM's emulator doesn't filter out
NOPs when checking for nested intercepts. Failure to allow emulation of
NOPs results in KVM injecting a #UD into L2 on any NOP that collides with
the emulator's definition of PAUSE, i.e. on all single-byte NOPs.
For PAUSE itself, honor L1's PAUSE-exiting control, but ignore PLE to
avoid unnecessarily injecting a #UD into L2. Per the SDM, the first
execution of PAUSE after VM-Entry is treated as the beginning of a new
loop, i.e. will never trigger a PLE VM-Exit, and so L1 can't expect any
given execution of PAUSE to deterministically exit.
... the processor considers this execution to be the first execution of
PAUSE in a loop. (It also does so for the first execution of PAUSE at
CPL 0 after VM entry.)
All that said, the PLE side of things is currently a moot point, as KVM
doesn't expose PLE to L1.
Note, vmx_check_intercept() is still wildly broken when L1 wants to
intercept an instruction, as KVM injects a #UD instead of synthesizing a
nested VM-Exit. That issue extends far beyond NOP/PAUSE and needs far
more effort to fix, i.e. is a problem for the future.
Fixes: 07721feee4 ("KVM: nVMX: Don't emulate instructions in guest mode")
Cc: Mathias Krause <minipli@grsecurity.net>
Cc: stable@vger.kernel.org
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Link: https://lore.kernel.org/r/20230405002359.418138-1-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d82dcd9e21 upstream.
Reiserfs sets a security xattr at inode creation time in two stages: first,
it calls reiserfs_security_init() to obtain the xattr from active LSMs;
then, it calls reiserfs_security_write() to actually write that xattr.
Unfortunately, it seems there is a wrong expectation that LSMs provide the
full xattr name in the form 'security.<suffix>'. However, LSMs always
provided just the suffix, causing reiserfs to not write the xattr at all
(if the suffix is shorter than the prefix), or to write an xattr with the
wrong name.
Add a temporary buffer in reiserfs_security_write(), and write to it the
full xattr name, before passing it to reiserfs_xattr_set_handle().
Also replace the name length check with a check that the full xattr name is
not larger than XATTR_NAME_MAX.
Cc: stable@vger.kernel.org # v2.6.x
Fixes: 57fe60df62 ("reiserfs: add atomic addition of selinux attributes during inode creation")
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f900fde288 upstream.
The performance of the crypto fuzz tests has greatly regressed since
v5.18. When booting a kernel on an arm64 dev board with all software
crypto algorithms and CONFIG_CRYPTO_MANAGER_EXTRA_TESTS enabled, the
fuzz tests now take about 200 seconds to run, or about 325 seconds with
lockdep enabled, compared to about 5 seconds before.
The root cause is that the random number generation has become much
slower due to commit d4150779e6 ("random32: use real rng for
non-deterministic randomness"). On my same arm64 dev board, at the time
the fuzz tests are run, get_random_u8() is about 345x slower than
prandom_u32_state(), or about 469x if lockdep is enabled.
Lockdep makes a big difference, but much of the rest comes from the
get_random_*() functions taking a *very* slow path when the CRNG is not
yet initialized. Since the crypto self-tests run early during boot,
even having a hardware RNG driver enabled (CONFIG_CRYPTO_DEV_QCOM_RNG in
my case) doesn't prevent this. x86 systems don't have this issue, but
they still see a significant regression if lockdep is enabled.
Converting the "Fully random bytes" case in generate_random_bytes() to
use get_random_bytes() helps significantly, improving the test time to
about 27 seconds. But that's still over 5x slower than before.
This is all a bit silly, though, since the fuzz tests don't actually
need cryptographically secure random numbers. So let's just make them
use a non-cryptographically-secure RNG as they did before. The original
prandom_u32() is gone now, so let's use prandom_u32_state() instead,
with an explicitly managed state, like various other self-tests in the
kernel source tree (rbtree_test.c, test_scanf.c, etc.) already do. This
also has the benefit that no locking is required anymore, so performance
should be even better than the original version that used prandom_u32().
Fixes: d4150779e6 ("random32: use real rng for non-deterministic randomness")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47446d7cd4 upstream.
aesbs_ecb_encrypt(), aesbs_ecb_decrypt(), aesbs_xts_encrypt(), and
aesbs_xts_decrypt() are called via indirect function calls. Therefore
they need to use SYM_TYPED_FUNC_START instead of SYM_FUNC_START to cause
their type hashes to be emitted when the kernel is built with
CONFIG_CFI_CLANG=y. Otherwise, the code crashes with a CFI failure if
the compiler doesn't happen to optimize out the indirect calls.
Fixes: c50d32859e ("arm64: Add types to indirect called assembly functions")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a543ada7db upstream.
The crypto_unregister_alg() function expects callers to ensure that any
algorithm that is unregistered has a refcnt of exactly 1, and issues a
BUG_ON() if this is not the case. However, there are in fact drivers that
will call crypto_unregister_alg() without ensuring that the refcnt has been
lowered first, most notably on system shutdown. This causes the BUG_ON() to
trigger, which prevents a clean shutdown and hangs the system.
To avoid such hangs on shutdown, demote the BUG_ON() in
crypto_unregister_alg() to a WARN_ON() with early return. Cc stable because
this problem was observed on a 6.2 kernel, cf the link below.
Link: https://lore.kernel.org/r/87r0tyq8ph.fsf@toke.dk
Cc: stable@vger.kernel.org
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 675751bb20 upstream.
If something was written to the buffer just before destruction,
it may be possible (maybe not in a real system, but it did
happen in ARCH=um with time-travel) to destroy the ringbuffer
before the IRQ work ran, leading this KASAN report (or a crash
without KASAN):
BUG: KASAN: slab-use-after-free in irq_work_run_list+0x11a/0x13a
Read of size 8 at addr 000000006d640a48 by task swapper/0
CPU: 0 PID: 0 Comm: swapper Tainted: G W O 6.3.0-rc1 #7
Stack:
60c4f20f 0c203d48 41b58ab3 60f224fc
600477fa 60f35687 60c4f20f 601273dd
00000008 6101eb00 6101eab0 615be548
Call Trace:
[<60047a58>] show_stack+0x25e/0x282
[<60c609e0>] dump_stack_lvl+0x96/0xfd
[<60c50d4c>] print_report+0x1a7/0x5a8
[<603078d3>] kasan_report+0xc1/0xe9
[<60308950>] __asan_report_load8_noabort+0x1b/0x1d
[<60232844>] irq_work_run_list+0x11a/0x13a
[<602328b4>] irq_work_tick+0x24/0x34
[<6017f9dc>] update_process_times+0x162/0x196
[<6019f335>] tick_sched_handle+0x1a4/0x1c3
[<6019fd9e>] tick_sched_timer+0x79/0x10c
[<601812b9>] __hrtimer_run_queues.constprop.0+0x425/0x695
[<60182913>] hrtimer_interrupt+0x16c/0x2c4
[<600486a3>] um_timer+0x164/0x183
[...]
Allocated by task 411:
save_stack_trace+0x99/0xb5
stack_trace_save+0x81/0x9b
kasan_save_stack+0x2d/0x54
kasan_set_track+0x34/0x3e
kasan_save_alloc_info+0x25/0x28
____kasan_kmalloc+0x8b/0x97
__kasan_kmalloc+0x10/0x12
__kmalloc+0xb2/0xe8
load_elf_phdrs+0xee/0x182
[...]
The buggy address belongs to the object at 000000006d640800
which belongs to the cache kmalloc-1k of size 1024
The buggy address is located 584 bytes inside of
freed 1024-byte region [000000006d640800, 000000006d640c00)
Add the appropriate irq_work_sync() so the work finishes before
the buffers are destroyed.
Prior to the commit in the Fixes tag below, there was only a
single global IRQ work, so this issue didn't exist.
Link: https://lore.kernel.org/linux-trace-kernel/20230427175920.a76159263122.I8295e405c44362a86c995e9c2c37e3e03810aa56@changeid
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Fixes: 15693458c4 ("tracing/ring-buffer: Move poll wake ups into ring buffer code")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c339fb4d8 upstream.
In ring_buffer_reset_online_cpus, the buffer_size_kb write operation
may permanently fail if the cpu_online_mask changes between two
for_each_online_buffer_cpu loops. The number of increases and decreases
on both cpu_buffer->resize_disabled and cpu_buffer->record_disabled may be
inconsistent, causing some CPUs to have non-zero values for these atomic
variables after the function returns.
This issue can be reproduced by "echo 0 > trace" while hotplugging cpu.
After reproducing success, we can find out buffer_size_kb will not be
functional anymore.
To prevent leaving 'resize_disabled' and 'record_disabled' non-zero after
ring_buffer_reset_online_cpus returns, we ensure that each atomic variable
has been set up before atomic_sub() to it.
Link: https://lore.kernel.org/linux-trace-kernel/20230426062027.17451-1-Tze-nan.Wu@mediatek.com
Cc: stable@vger.kernel.org
Cc: <mhiramat@kernel.org>
Cc: npiggin@gmail.com
Fixes: b23d7a5f4a ("ring-buffer: speed up buffer resets by avoiding synchronize_rcu for each CPU")
Reviewed-by: Cheng-Jui Wang <cheng-jui.wang@mediatek.com>
Signed-off-by: Tze-nan Wu <Tze-nan.Wu@mediatek.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eb411c0cf5 upstream.
This fix is basically the same as 9bce02ef0d ("pwm: meson: Fix the
G12A AO clock parents order"). Vendor driver referenced there has
xtal as first parent also for axg ao. In addition fix the name
of the aoclk81 clock. Apparently name aoclk81 as used by the vendor
driver was changed when mainlining the axg clock driver.
Fixes: bccaa3f917 ("pwm: meson: Add clock source configuration for Meson-AXG")
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b8ccdfb94 upstream.
According to the documentation, ieee80211_rx_list must not run concurrently
with ieee80211_tx_status (or its variants).
Cc: stable@vger.kernel.org
Fixes: 88046b2c9f ("mt76: add support for reporting tx status with skb")
Reported-by: Brian Coverstone <brian@mainsequence.net>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d2555cde2 upstream.
The ipmi communication is not restored after a specific version of BMC is
upgraded on our server.
The ipmi driver does not respond after printing the following log:
ipmi_ssif: Invalid response getting flags: 1c 1
I found that after entering this branch, ssif_info->ssif_state always
holds SSIF_GETTING_FLAGS and never return to IDLE.
As a result, the driver cannot be loaded, because the driver status is
checked during the unload process and must be IDLE in shutdown_ssif():
while (ssif_info->ssif_state != SSIF_IDLE)
schedule_timeout(1);
The process trigger this problem is:
1. One msg timeout and next msg start send, and call
ssif_set_need_watch().
2. ssif_set_need_watch()->watch_timeout()->start_flag_fetch() change
ssif_state to SSIF_GETTING_FLAGS.
3. In msg_done_handler() ssif_state == SSIF_GETTING_FLAGS, if an error
message is received, the second branch does not modify the ssif_state.
4. All retry action need IS_SSIF_IDLE() == True. Include retry action in
watch_timeout(), msg_done_handler(). Sending msg does not work either.
SSIF_IDLE is also checked in start_next_msg().
5. The only thing that can be triggered in the SSIF driver is
watch_timeout(), after destory_user(), this timer will stop too.
So, if enter this branch, the ssif_state will remain SSIF_GETTING_FLAGS
and can't send msg, no timer started, can't unload.
We did a comparative test before and after adding this patch, and the
result is effective.
Fixes: 259307074b ("ipmi: Add SMBus interface driver (SSIF)")
Cc: stable@vger.kernel.org
Signed-off-by: Zhang Yuchen <zhangyuchen.lcr@bytedance.com>
Message-Id: <20230412074907.80046-1-zhangyuchen.lcr@bytedance.com>
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e3184de9d4 upstream.
'obj-$(CONFIG_SYSCTL) += sysctls.o' must be moved after "obj-y :=",
or it won't be built as it is overwrited.
Note that there is nothing that is going to break by linking
sysctl.o later, we were just being way to cautious and patches
have been updated to reflect these considerations and sent for
stable as well with the whole "base" stuff needing to be linked
prior to child sysctl tables that use that directory. All of
the kernel sysctl APIs always share the same directory, and races
against using it should end up re-using the same single created
directory.
And so something we can do eventually is do away with all the base stuff.
For now it's fine, it's not creating an issue. It is just a bit pedantic
and careful.
Fixes: ab171b952c ("fs: move namespace sysctls and declare fs base directory")
Cc: stable@vger.kernel.org # v5.17
Cc: Christian Brauner <brauner@kernel.org>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
[mcgrof: enhanced commit log for stable criteria and clarify base stuff ]
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58d7668242 upstream.
For CONFIG_NO_HZ_FULL systems, the tick_do_timer_cpu cannot be offlined.
However, cpu_is_hotpluggable() still returns true for those CPUs. This causes
torture tests that do offlining to end up trying to offline this CPU causing
test failures. Such failure happens on all architectures.
Fix the repeated error messages thrown by this (even if the hotplug errors are
harmless) by asking the opinion of the nohz subsystem on whether the CPU can be
hotplugged.
[ Apply Frederic Weisbecker feedback on refactoring tick_nohz_cpu_down(). ]
For drivers/base/ portion:
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Frederic Weisbecker <frederic@kernel.org>
Cc: Frederic Weisbecker <frederic@kernel.org>
Cc: "Paul E. McKenney" <paulmck@kernel.org>
Cc: Zhouyi Zhou <zhouzhouyi@gmail.com>
Cc: Will Deacon <will@kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: rcu <rcu@vger.kernel.org>
Cc: stable@vger.kernel.org
Fixes: 2987557f52 ("driver-core/cpu: Expose hotpluggability to the rest of the kernel")
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f42b142ea upstream.
After upgrading from 5.16 to 6.1, our board with a MAX14830 started
producing lots of garbage data over UART. Bisection pointed out commit
285e76fc04 as the culprit. That patch tried to replace hand-written
code which I added in 2b4bac48c1 ("serial: max310x: Use batched reads
when reasonably safe") with the generic regmap infrastructure for
batched operations.
Unfortunately, the `regmap_raw_read` and `regmap_raw_write` which were
used are actually functions which perform IO over *multiple* registers.
That's not what is needed for accessing these Tx/Rx FIFOs; the
appropriate functions are the `_noinc_` versions, not the `_raw_` ones.
Fix this regression by using `regmap_noinc_read()` and
`regmap_noinc_write()` along with the necessary `regmap_config` setup;
with this patch in place, our board communicates happily again. Since
our board uses SPI for talking to this chip, the I2C part is completely
untested.
Fixes: 285e76fc04 ("serial: max310x: use regmap methods for SPI batch operations")
Cc: stable@vger.kernel.org
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Link: https://lore.kernel.org/r/79db8e82aadb0e174bc82b9996423c3503c8fb37.1680732084.git.jan.kundrat@cesnet.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 146a37e05d upstream.
There's a potential race before THRE/TEMT deasserts when DMA Tx is
starting up (or the next batch of continuous Tx is being submitted).
This can lead to misdetecting Tx empty condition.
It is entirely normal for THRE/TEMT to be set for some time after the
DMA Tx had been setup in serial8250_tx_dma(). As Tx side is definitely
not empty at that point, it seems incorrect for serial8250_tx_empty()
claim Tx is empty.
Fix the race by also checking in serial8250_tx_empty() whether there's
DMA Tx active.
Note: This fix only addresses in-kernel race mainly to make using
TCSADRAIN/FLUSH robust. Userspace can still cause other races but they
seem userspace concurrency control problems.
Fixes: 9ee4b83e51 ("serial: 8250: Add support for dmaengine")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230317113318.31327-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 094fb49a2d upstream.
If userspace races tcsetattr() with a write, the drained condition
might not be guaranteed by the kernel. There is a race window after
checking Tx is empty before tty_set_termios() takes termios_rwsem for
write. During that race window, more characters can be queued by a
racing writer.
Any ongoing transmission might produce garbage during HW's
->set_termios() call. The intent of TCSADRAIN/FLUSH seems to be
preventing such a character corruption. If those flags are set, take
tty's write lock to stop any writer before performing the lower layer
Tx empty check and wait for the pending characters to be sent (if any).
The initial wait for all-writers-done must be placed outside of tty's
write lock to avoid deadlock which makes it impossible to use
tty_wait_until_sent(). The write lock is retried if a racing write is
detected.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230317113318.31327-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c7cb94452 upstream.
If blk_crypto_evict_key() sees that the key is still in-use (due to a
bug) or that ->keyslot_evict failed, it currently just returns while
leaving the key linked into the keyslot management structures.
However, blk_crypto_evict_key() is only called in contexts such as inode
eviction where failure is not an option. So actually the caller
proceeds with freeing the blk_crypto_key regardless of the return value
of blk_crypto_evict_key().
These two assumptions don't match, and the result is that there can be a
use-after-free in blk_crypto_reprogram_all_keys() after one of these
errors occurs. (Note, these errors *shouldn't* happen; we're just
talking about what happens if they do anyway.)
Fix this by making blk_crypto_evict_key() unlink the key from the
keyslot management structures even on failure.
Also improve some comments.
Fixes: 1b26283970 ("block: Keyslot Manager for Inline Encryption")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230315183907.53675-2-ebiggers@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9cd1e56667 upstream.
Once all I/O using a blk_crypto_key has completed, filesystems can call
blk_crypto_evict_key(). However, the block layer currently doesn't call
blk_crypto_put_keyslot() until the request is being freed, which happens
after upper layers have been told (via bio_endio()) the I/O has
completed. This causes a race condition where blk_crypto_evict_key()
can see 'slot_refs != 0' without there being an actual bug.
This makes __blk_crypto_evict_key() hit the
'WARN_ON_ONCE(atomic_read(&slot->slot_refs) != 0)' and return without
doing anything, eventually causing a use-after-free in
blk_crypto_reprogram_all_keys(). (This is a very rare bug and has only
been seen when per-file keys are being used with fscrypt.)
There are two options to fix this: either release the keyslot before
bio_endio() is called on the request's last bio, or make
__blk_crypto_evict_key() ignore slot_refs. Let's go with the first
solution, since it preserves the ability to report bugs (via
WARN_ON_ONCE) where a key is evicted while still in-use.
Fixes: a892c8d52c ("block: Inline encryption support for blk-mq")
Cc: stable@vger.kernel.org
Reviewed-by: Nathan Huckleberry <nhuck@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20230315183907.53675-2-ebiggers@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 20de765f6d upstream.
We need to set QUEUE_FLAG_STATS for two cases:
1. blk_stat_enable_accounting()
2. blk_stat_add_callback()
So we should clear it only when ((q->stats->accounting == 0) &&
list_empty(&q->stats->callbacks)).
blk_stat_disable_accounting() only check if q->stats->accounting
is 0 before clear the flag, this patch fix it.
Also add list_empty(&q->stats->callbacks)) check when enable, or
the flag is already set.
The bug can be reproduced on kernel without BLK_DEV_THROTTLING
(since it unconditionally enable accounting, see the next patch).
# cat /sys/block/sr0/queue/scheduler
none mq-deadline [bfq]
# cat /sys/kernel/debug/block/sr0/state
SAME_COMP|IO_STAT|INIT_DONE|STATS|REGISTERED|NOWAIT|30
# echo none > /sys/block/sr0/queue/scheduler
# cat /sys/kernel/debug/block/sr0/state
SAME_COMP|IO_STAT|INIT_DONE|REGISTERED|NOWAIT
# cat /sys/block/sr0/queue/wbt_lat_usec
75000
We can see that after changing elevator from "bfq" to "none",
"STATS" flag is lost even though WBT callback still need it.
Fixes: 68497092bd ("block: make queue stat accounting a reference")
Cc: <stable@vger.kernel.org> # v5.17+
Signed-off-by: Chengming Zhou <zhouchengming@bytedance.com>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20230413062805.2081970-1-chengming.zhou@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a37a512db3 upstream.
Legacy Display Unit (LDU) fb dirty support used a custom fb dirty callback. Latter
handled only the DIRTYFB IOCTL presentation path but not the ADDFB2/PAGE_FLIP/RMFB
IOCTL path, common for Wayland compositors.
Get rid of the custom callback in favor of drm_atomic_helper_dirtyfb and unify the
handling of the presentation paths inside of vmw_ldu_primary_plane_atomic_update.
This also homogenizes the fb dirty callbacks across all DUs: LDU, SOU and STDU.
Signed-off-by: Martin Krastev <krastevm@vmware.com>
Reviewed-by: Maaz Mombasawala <mombasawalam@vmware.com>
Fixes: 2f5544ff03 ("drm/vmwgfx: Use atomic helper function for dirty fb IOCTL")
Cc: <stable@vger.kernel.org> # v5.0+
Signed-off-by: Zack Rusin <zackr@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230321020949.335012-3-zack@kde.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a4e1b5aed upstream.
It the device is probed in non-zero ACPI D state, the module
identification is delayed until the first streamon.
The module identification has two parts: deviceID and version. To rea
the version we have to enable OTP read. This cannot be done during
streamon, becase it modifies REG_MODE_SELECT.
Since the driver has the same behaviour for all the module versions, do
not read the module version from the sensor's OTP.
Cc: stable@vger.kernel.org
Fixes: 0e014f1a8d ("media: ov8856: support device probe in non-zero ACPI D state")
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7abf14f00 upstream.
For some unknown reason the introduction of the timer_wait_running callback
missed to fixup posix CPU timers, which went unnoticed for almost four years.
Marco reported recently that the WARN_ON() in timer_wait_running()
triggers with a posix CPU timer test case.
Posix CPU timers have two execution models for expiring timers depending on
CONFIG_POSIX_CPU_TIMERS_TASK_WORK:
1) If not enabled, the expiry happens in hard interrupt context so
spin waiting on the remote CPU is reasonably time bound.
Implement an empty stub function for that case.
2) If enabled, the expiry happens in task work before returning to user
space or guest mode. The expired timers are marked as firing and moved
from the timer queue to a local list head with sighand lock held. Once
the timers are moved, sighand lock is dropped and the expiry happens in
fully preemptible context. That means the expiring task can be scheduled
out, migrated, interrupted etc. So spin waiting on it is more than
suboptimal.
The timer wheel has a timer_wait_running() mechanism for RT, which uses
a per CPU timer-base expiry lock which is held by the expiry code and the
task waiting for the timer function to complete blocks on that lock.
This does not work in the same way for posix CPU timers as there is no
timer base and expiry for process wide timers can run on any task
belonging to that process, but the concept of waiting on an expiry lock
can be used too in a slightly different way:
- Add a mutex to struct posix_cputimers_work. This struct is per task
and used to schedule the expiry task work from the timer interrupt.
- Add a task_struct pointer to struct cpu_timer which is used to store
a the task which runs the expiry. That's filled in when the task
moves the expired timers to the local expiry list. That's not
affecting the size of the k_itimer union as there are bigger union
members already
- Let the task take the expiry mutex around the expiry function
- Let the waiter acquire a task reference with rcu_read_lock() held and
block on the expiry mutex
This avoids spin-waiting on a task which might not even be on a CPU and
works nicely for RT too.
Fixes: ec8f954a40 ("posix-timers: Use a callback for cancel synchronization on PREEMPT_RT")
Reported-by: Marco Elver <elver@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marco Elver <elver@google.com>
Tested-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87zg764ojw.ffs@tglx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 02435a739b upstream.
It was observed that there are hosts that may complete pending SETUP
transactions before the stop active transfers and controller halt occurs,
leading to lingering endxfer commands on DEPs on subsequent pullup/gadget
start iterations.
dwc3_gadget_ep_disable name=ep8in flags=0x3009 direction=1
dwc3_gadget_ep_disable name=ep4in flags=1 direction=1
dwc3_gadget_ep_disable name=ep3out flags=1 direction=0
usb_gadget_disconnect deactivated=0 connected=0 ret=0
The sequence shows that the USB gadget disconnect (dwc3_gadget_pullup(0))
routine completed successfully, allowing for the USB gadget to proceed with
a USB gadget connect. However, if this occurs the system runs into an
issue where:
BUG: spinlock already unlocked on CPU
spin_bug+0x0
dwc3_remove_requests+0x278
dwc3_ep0_out_start+0xb0
__dwc3_gadget_start+0x25c
This is due to the pending endxfers, leading to gadget start (w/o lock
held) to execute the remove requests, which will unlock the dwc3
spinlock as part of giveback.
To mitigate this, resolve the pending endxfers on the pullup disable
path by re-locating the SETUP phase check after stop active transfers, since
that is where the DWC3_EP_DELAY_STOP is potentially set. This also allows
for handling of a host that may be unresponsive by using the completion
timeout to trigger the stall and restart for EP0.
Fixes: c96683798e ("usb: dwc3: ep0: Don't prepare beyond Setup stage")
Cc: stable@vger.kernel.org
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20230413195742.11821-2-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0db213ea8e upstream.
usb_udc_connect_control does not check to see if the udc has already
been started. This causes gadget->ops->pullup to be called through
usb_gadget_connect when invoked from usb_udc_vbus_handler even before
usb_gadget_udc_start is called. Guard this by checking for udc->started
in usb_udc_connect_control before invoking usb_gadget_connect.
Guarding udc->vbus, udc->started, gadget->connect, gadget->deactivate
related functions with connect_lock. usb_gadget_connect_locked,
usb_gadget_disconnect_locked, usb_udc_connect_control_locked,
usb_gadget_udc_start_locked, usb_gadget_udc_stop_locked are called with
this lock held as they can be simulataneously invoked from different code
paths.
Adding an additional check to make sure udc is started(udc->started)
before pullup callback is invoked.
Fixes: 628ef0d273 ("usb: udc: add usb_udc_vbus_handler")
Cc: stable@vger.kernel.org
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20230407030741.3163220-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6f187f92b upstream.
The RTW88 chipsets have four different priority queues in hardware. For
the USB type chipsets the packets destined for a specific priority queue
must be sent through the endpoint corresponding to the queue. This was
not fully understood when porting from the RTW88 USB out of tree driver
and thus violated.
This patch implements the qsel to endpoint mapping as in
get_usb_bulkout_id_88xx() in the downstream driver.
Without this the driver often issues "timed out to flush queue 3"
warnings and often TX stalls completely.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: ValdikSS <iam@valdikss.org.ru>
Tested-by: Alexandru gagniuc <mr.nuke.me@gmail.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable@vger.kernel.org
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230417140358.2240429-2-s.hauer@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 644f17412f upstream.
UML supports HAS_IOMEM since 0bbadafdc4 (um: allow disabling
NO_IOMEM).
Current IMA build on UML fails on allmodconfig (with TCG_TPM=m):
ld: security/integrity/ima/ima_queue.o: in function `ima_add_template_entry':
ima_queue.c:(.text+0x2d9): undefined reference to `tpm_pcr_extend'
ld: security/integrity/ima/ima_init.o: in function `ima_init':
ima_init.c:(.init.text+0x43f): undefined reference to `tpm_default_chip'
ld: security/integrity/ima/ima_crypto.o: in function `ima_calc_boot_aggregate_tfm':
ima_crypto.c:(.text+0x1044): undefined reference to `tpm_pcr_read'
ld: ima_crypto.c:(.text+0x10d8): undefined reference to `tpm_pcr_read'
Modify the IMA Kconfig entry so that it selects TCG_TPM if HAS_IOMEM
is set, regardless of the UML Kconfig setting.
This updates TCG_TPM from =m to =y and fixes the linker errors.
Fixes: f4a0391dfa ("ima: fix Kconfig dependencies")
Cc: Stable <stable@vger.kernel.org> # v5.14+
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: linux-um@lists.infradead.org
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14853a0676 upstream.
This reverts commit 2d5253a096.
There are 2 commits with commit message "Add a secondary AT port to Telit
FN990":
commit 2d5253a096 ("bus: mhi: host: pci_generic: Add a secondary AT port
to Telit FN990")
commit 479aa3b0ec ("bus: mhi: host: pci_generic: Add a secondary AT port
to Telit FN990")
This turned out to be due to the patch getting applied through different
trees and git settled on a resolution while applying it second time. But
the second AT port of Foxconn devices don't work in PCIe mode. So the
second commit needs to be reverted.
Cc: stable@vger.kernel.org # 6.2
Fixes: 2d5253a096 ("bus: mhi: host: pci_generic: Add a secondary AT port to Telit FN990")
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Reviewed-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://lore.kernel.org/r/20230310101715.69209-1-slark_xiao@163.com
[mani: massaged the commit message a bit, added fixes tag and CCed stable]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f5eff5591b upstream.
In 2013, commits
2e35afaefe ("PCI: pciehp: Add reset_slot() method")
608c388122 ("PCI: Add slot reset option to pci_dev_reset()")
amended PCIe hotplug to mask Presence Detect Changed events during a
Secondary Bus Reset. The reset thus no longer causes gratuitous slot
bringdown and bringup.
However the commits neglected to serialize reset with code paths reading
slot registers. For instance, a slot bringup due to an earlier hotplug
event may see the Presence Detect State bit cleared during a concurrent
Secondary Bus Reset.
In 2018, commit
5b3f7b7d06 ("PCI: pciehp: Avoid slot access during reset")
retrofitted the missing locking. It introduced a reset_lock which
serializes a Secondary Bus Reset with other parts of pciehp.
Unfortunately the locking turns out to be overzealous: reset_lock is
held for the entire enumeration and de-enumeration of hotplugged devices,
including driver binding and unbinding.
Driver binding and unbinding acquires device_lock while the reset_lock
of the ancestral hotplug port is held. A concurrent Secondary Bus Reset
acquires the ancestral reset_lock while already holding the device_lock.
The asymmetric locking order in the two code paths can lead to AB-BA
deadlocks.
Michael Haeuptle reports such deadlocks on simultaneous hot-removal and
vfio release (the latter implies a Secondary Bus Reset):
pciehp_ist() # down_read(reset_lock)
pciehp_handle_presence_or_link_change()
pciehp_disable_slot()
__pciehp_disable_slot()
remove_board()
pciehp_unconfigure_device()
pci_stop_and_remove_bus_device()
pci_stop_bus_device()
pci_stop_dev()
device_release_driver()
device_release_driver_internal()
__device_driver_lock() # device_lock()
SYS_munmap()
vfio_device_fops_release()
vfio_device_group_close()
vfio_device_close()
vfio_device_last_close()
vfio_pci_core_close_device()
vfio_pci_core_disable() # device_lock()
__pci_reset_function_locked()
pci_reset_bus_function()
pci_dev_reset_slot_function()
pci_reset_hotplug_slot()
pciehp_reset_slot() # down_write(reset_lock)
Ian May reports the same deadlock on simultaneous hot-removal and an
AER-induced Secondary Bus Reset:
aer_recover_work_func()
pcie_do_recovery()
aer_root_reset()
pci_bus_error_reset()
pci_slot_reset()
pci_slot_lock() # device_lock()
pci_reset_hotplug_slot()
pciehp_reset_slot() # down_write(reset_lock)
Fix by releasing the reset_lock during driver binding and unbinding,
thereby splitting and shrinking the critical section.
Driver binding and unbinding is protected by the device_lock() and thus
serialized with a Secondary Bus Reset. There's no need to additionally
protect it with the reset_lock. However, pciehp does not bind and
unbind devices directly, but rather invokes PCI core functions which
also perform certain enumeration and de-enumeration steps.
The reset_lock's purpose is to protect slot registers, not enumeration
and de-enumeration of hotplugged devices. That would arguably be the
job of the PCI core, not the PCIe hotplug driver. After all, an
AER-induced Secondary Bus Reset may as well happen during boot-time
enumeration of the PCI hierarchy and there's no locking to prevent that
either.
Exempting *de-enumeration* from the reset_lock is relatively harmless:
A concurrent Secondary Bus Reset may foil config space accesses such as
PME interrupt disablement. But if the device is physically gone, those
accesses are pointless anyway. If the device is physically present and
only logically removed through an Attention Button press or the sysfs
"power" attribute, PME interrupts as well as DMA cannot come through
because pciehp_unconfigure_device() disables INTx and Bus Master bits.
That's still protected by the reset_lock in the present commit.
Exempting *enumeration* from the reset_lock also has limited impact:
The exempted call to pci_bus_add_device() may perform device accesses
through pcibios_bus_add_device() and pci_fixup_device() which are now
no longer protected from a concurrent Secondary Bus Reset. Otherwise
there should be no impact.
In essence, the present commit seeks to fix the AB-BA deadlocks while
still retaining a best-effort reset protection for enumeration and
de-enumeration of hotplugged devices -- until a general solution is
implemented in the PCI core.
Link: https://lore.kernel.org/linux-pci/CS1PR8401MB0728FC6FDAB8A35C22BD90EC95F10@CS1PR8401MB0728.NAMPRD84.PROD.OUTLOOK.COM
Link: https://lore.kernel.org/linux-pci/20200615143250.438252-1-ian.may@canonical.com
Link: https://lore.kernel.org/linux-pci/ce878dab-c0c4-5bd0-a725-9805a075682d@amd.com
Link: https://lore.kernel.org/linux-pci/ed831249-384a-6d35-0831-70af191e9bce@huawei.com
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215590
Fixes: 5b3f7b7d06 ("PCI: pciehp: Avoid slot access during reset")
Link: https://lore.kernel.org/r/fef2b2e9edf245c049a8c5b94743c0f74ff5008a.1681191902.git.lukas@wunner.de
Reported-by: Michael Haeuptle <michael.haeuptle@hpe.com>
Reported-by: Ian May <ian.may@canonical.com>
Reported-by: Andrey Grodzovsky <andrey2805@gmail.com>
Reported-by: Rahul Kumar <rahul.kumar1@amd.com>
Reported-by: Jialin Zhang <zhangjialin11@huawei.com>
Tested-by: Anatoli Antonovitch <Anatoli.Antonovitch@amd.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v4.19+
Cc: Dan Stein <dstein@hpe.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Alex Michon <amichon@kalrayinc.com>
Cc: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Sathyanarayanan Kuppuswamy <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a2776e8a0 upstream.
pcie-kirin uses regmaps, and needs to pull them in; otherwise, with
CONFIG_PCIE_KIRIN=y and without CONFIG_REGMAP_MMIO pcie-kirin produces
a linker failure looking for __devm_regmap_init_mmio_clk().
Fixes: d19afe7be1 ("PCI: kirin: Use regmap for APB registers")
Link: https://lore.kernel.org/r/04636141da1d6d592174eefb56760511468d035d.1668410580.git.josh@joshtriplett.org
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
[lpieralisi@kernel.org: commit log and removed REGMAP select]
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Cc: stable@vger.kernel.org # 5.16+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09d4d6da1b upstream.
When the BIOS has been configured for Fast Boot, systems with mt7921e
have non-functional wifi. Turning on Fast boot caused both bus master
enable and memory space enable bits in PCI_COMMAND not to get configured.
The mt7921 driver already sets bus master enable, but explicitly check
and set memory access enable as well to fix this problem.
Tested-by: Anson Tsao <anson.tsao@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e7757876f upstream.
After upgrading build guests to v6.3, rpm started segfaulting for
specific packages, which was bisected to commit 0503ea8f5b ("mm/mmap:
remove __vma_adjust()"). rpm is doing many mremap() operations with file
mappings of its db. The problem is that in vma_merge() case 3 (we merge
with the next vma, expanding it downwards) vm_pgoff is not adjusted as
it should when vm_start changes. As a result the rpm process most likely
sees data from the wrong offset of the file. Fix the vm_pgoff
calculation.
For case 8 this is a non-functional change as the resulting vm_pgoff is
the same.
Reported-and-bisected-by: Jiri Slaby <jirislaby@kernel.org>
Reported-and-tested-by: Fabian Vogt <fvogt@suse.com>
Link: https://bugzilla.suse.com/show_bug.cgi?id=1210903
Fixes: 0503ea8f5b ("mm/mmap: remove __vma_adjust()")
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ba7d5f5ba upstream.
There are some warnings on older compilers (gcc 10, 7) or non-x86_64
architectures (aarch64). As btrfs wants to enable -Wmaybe-uninitialized
by default, fix the warnings even though it's not necessary on recent
compilers (gcc 12+).
../fs/btrfs/volumes.c: In function ‘btrfs_init_new_device’:
../fs/btrfs/volumes.c:2703:3: error: ‘seed_devices’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
2703 | btrfs_setup_sprout(fs_info, seed_devices);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../fs/btrfs/send.c: In function ‘get_cur_inode_state’:
../include/linux/compiler.h:70:32: error: ‘right_gen’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
70 | (__if_trace.miss_hit[1]++,1) : \
| ^
../fs/btrfs/send.c:1878:6: note: ‘right_gen’ was declared here
1878 | u64 right_gen;
| ^~~~~~~~~
Reported-by: k2ci <kernel-bot@kylinos.cn>
Signed-off-by: Genjian Zhang <zhanggenjian@kylinos.cn>
Reviewed-by: David Sterba <dsterba@suse.com>
[ update changelog ]
Signed-off-by: David Sterba <dsterba@suse.com>
Cc: Ammar Faizi <ammarfaizi2@gnuweeb.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc4cffc3c1 upstream.
Add SDIO ids for use with the muRata 1YN (Cypress CYW43439).
The odd thing about this is that the previous 1YN populated
on M.2 card for evaluation purposes had BRCM SDIO vendor ID,
while the chip populated on real hardware has a Cypress one.
The device ID also differs between the two devices. But they
are both 43439 otherwise, so add the IDs for both.
On-device 1YN (43439), the new one, chip label reads "1YN":
```
/sys/.../mmc_host/mmc2/mmc2:0001 # cat vendor device
0x04b4
0xbd3d
```
EA M.2 evaluation board 1YN (43439), the old one, chip label reads "1YN ES1.4":
```
/sys/.../mmc_host/mmc0/mmc0:0001/# cat vendor device
0x02d0
0xa9a6
```
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230407203752.128539-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 25c150ac10 upstream.
Previously, capability was checked using capable(), which verified that the
caller of the ioctl system call had the required capability. In addition,
the result of the check would be stored in the HCI_SOCK_TRUSTED flag,
making it persistent for the socket.
However, malicious programs can abuse this approach by deliberately sharing
an HCI socket with a privileged task. The HCI socket will be marked as
trusted when the privileged task occasionally makes an ioctl call.
This problem can be solved by using sk_capable() to check capability, which
ensures that not only the current task but also the socket opener has the
specified capability, thus reducing the risk of privilege escalation
through the previously identified vulnerability.
Cc: stable@vger.kernel.org
Fixes: f81f5b2db8 ("Bluetooth: Send control open and close messages for HCI raw sockets")
Signed-off-by: Ruihan Li <lrh2000@pku.edu.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 782eea0c89 upstream.
commit 1796f808e4 ("HID: i2c-hid: acpi: Stop setting wakeup_capable")
changed the policy such that I2C touchpads may be able to wake up the
system by default if the system is configured as such.
However on Clevo NL5xNU there is a mistake in the ACPI tables that the
TP_ATTN# signal connected to GPIO 9 is configured as ActiveLow and level
triggered but connected to a pull up. As soon as the system suspends the
touchpad loses power and then the system wakes up.
To avoid this problem, introduce a quirk for this model that will prevent
the wakeup capability for being set for GPIO 9.
This patch is analoge to a very similar patch for NL5xRU, just the DMI
string changed.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Cc: stable@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39049b69ec upstream.
The new Merkle tree construction algorithm is a bit fragile in that it
may overflow the 'root_hash' array if the tree actually generated does
not match the calculated tree parameters.
This should never happen unless there is a filesystem bug that allows
the file size to change despite deny_write_access(), or a bug in the
Merkle tree logic itself. Regardless, it's fairly easy to check for
buffer overflow here, so let's do so.
This is a robustness improvement only; this case is not currently known
to be reachable. I've added a Fixes tag anyway, since I recommend that
this be included in kernels that have the mentioned commit.
Fixes: 56124d6c87 ("fsverity: support enabling with tree block size < PAGE_SIZE")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230328041505.110162-1-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0483913921 upstream.
Commit 56124d6c87 ("fsverity: support enabling with tree block size <
PAGE_SIZE") changed FS_IOC_ENABLE_VERITY to use __kernel_read() to read
the file's data, instead of direct pagecache accesses.
An unintended consequence of this is that the
'WARN_ON_ONCE(!(file->f_mode & FMODE_READ))' in __kernel_read() became
reachable by fuzz tests. This happens if FS_IOC_ENABLE_VERITY is called
on a fd opened with access mode 3, which means "ioctl access only".
Arguably, FS_IOC_ENABLE_VERITY should work on ioctl-only fds. But
ioctl-only fds are a weird Linux extension that is rarely used and that
few people even know about. (The documentation for FS_IOC_ENABLE_VERITY
even specifically says it requires O_RDONLY.) It's probably not
worthwhile to make the ioctl internally open a new fd just to handle
this case. Thus, just reject the ioctl on such fds for now.
Fixes: 56124d6c87 ("fsverity: support enabling with tree block size < PAGE_SIZE")
Reported-by: syzbot+51177e4144d764827c45@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?id=2281afcbbfa8fdb92f9887479cc0e4180f1c6b28
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230406215106.235829-1-ebiggers@kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
description:Create a report to help us fix your issue
body:
- type:markdown
attributes:
value:|
**Is this the right place for my bug report?**
This repository contains the Linux kernel used on the Raspberry Pi.
If you believe that the issue you are seeing is kernel-related, this is the right place.
If not, we have other repositories for the GPU firmware at [github.com/raspberrypi/firmware](https://github.com/raspberrypi/firmware) and Raspberry Pi userland applications at [github.com/raspberrypi/userland](https://github.com/raspberrypi/userland).
If you have problems with the Raspbian distribution packages, report them in the [github.com/RPi-Distro/repo](https://github.com/RPi-Distro/repo).
If you simply have a question, then [the Raspberry Pi forums](https://www.raspberrypi.org/forums) are the best place to ask it.
- type:textarea
id:description
attributes:
label:Describe the bug
description:|
Add a clear and concise description of what you think the bug is.
validations:
required:true
- type:textarea
id:reproduce
attributes:
label:Steps to reproduce the behaviour
description:|
List the steps required to reproduce the issue.
validations:
required:true
- type:dropdown
id:model
attributes:
label:Device (s)
description:Onwhich device you are facing the bug?
multiple:true
options:
- Raspberry Pi Zero
- Raspberry Pi Zero W/WH
- Raspberry Pi Zero 2 W
- Raspberry Pi 1 Mod. A
- Raspberry Pi 1 Mod. A+
- Raspberry Pi 1 Mod. B
- Raspberry Pi 1 Mod. B+
- Raspberry Pi 2 Mod. B
- Raspberry Pi 2 Mod. B v1.2
- Raspberry Pi 3 Mod. A+
- Raspberry Pi 3 Mod. B
- Raspberry Pi 3 Mod. B+
- Raspberry Pi 4 Mod. B
- Raspberry Pi 400
- Raspberry Pi CM1
- Raspberry Pi CM3
- Raspberry Pi CM3 Lite
- Raspberry Pi CM3+
- Raspberry Pi CM3+ Lite
- Raspberry Pi CM4
- Raspberry Pi CM4 Lite
- Other
validations:
required:true
- type:textarea
id:system
attributes:
label:System
description:|
Copy and paste the results of the raspinfo command in to this section.
Alternatively, copy and paste a pastebin link, or add answers to the following questions:
* Which OS and version (`cat /etc/rpi-issue`)?
* Which firmware version (`vcgencmd version`)?
* Which kernel version (`uname -a`)?
validations:
required:true
- type:textarea
id:logs
attributes:
label:Logs
description:|
If applicable, add the relevant output from `dmesg` or similar.
about:"Please do not use GitHub for asking questions. If you simply have a question, then the Raspberry Pi forums are the best place to ask it. Thanks in advance for helping us keep the issue tracker clean!"
- name:"⛔ Problems with the Raspbian distribution packages"
url:https://github.com/RPi-Distro/repo
about:"If you have problems with the Raspbian distribution packages, please report them in the github.com/RPi-Distro/repo."
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
