commit 2e70570656 upstream.
A new warning in clang points out a place in this file where a bitwise
OR is being used with boolean types:
drivers/gpu/drm/i915/intel_pm.c:3066:12: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
changed = ilk_increase_wm_latency(dev_priv, dev_priv->wm.pri_latency, 12) |
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
This construct is intentional, as it allows every one of the calls to
ilk_increase_wm_latency() to occur (instead of short circuiting with
logical OR) while still caring about the result of each call.
To make this clearer to the compiler, use the '|=' operator to assign
the result of each ilk_increase_wm_latency() call to changed, which
keeps the meaning of the code the same but makes it obvious that every
one of these calls is expected to happen.
Link: https://github.com/ClangBuiltLinux/linux/issues/1473
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Suggested-by: Dávid Bolvanský <david.bolvansky@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211014211916.3550122-1-nathan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 502408a61f upstream.
A new warning in clang points out a place in this file where a bitwise
OR is being used with boolean expressions:
In file included from drivers/staging/wlan-ng/prism2usb.c:2:
drivers/staging/wlan-ng/hfa384x_usb.c:3787:7: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
((test_and_clear_bit(THROTTLE_RX, &hw->usb_flags) &&
~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/staging/wlan-ng/hfa384x_usb.c:3787:7: note: cast one or both operands to int to silence this warning
1 warning generated.
The comment explains that short circuiting here is undesirable, as the
calls to test_and_{clear,set}_bit() need to happen for both sides of the
expression.
Clang's suggestion would work to silence the warning but the readability
of the expression would suffer even more. To clean up the warning and
make the block more readable, use a variable for each side of the
bitwise expression.
Link: https://github.com/ClangBuiltLinux/linux/issues/1478
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20211014215703.3705371-1-nathan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7e67b8e80 upstream.
Currently, if CONFIG_RANDOM_TRUST_BOOTLOADER is enabled, multiple calls
to add_bootloader_randomness() are broken and can cause a NULL pointer
dereference, as noted by Ivan T. Ivanov. This is not only a hypothetical
problem, as qemu on arm64 may provide bootloader entropy via EFI and via
devicetree.
On the first call to add_hwgenerator_randomness(), crng_fast_load() is
executed, and if the seed is long enough, crng_init will be set to 1.
On subsequent calls to add_bootloader_randomness() and then to
add_hwgenerator_randomness(), crng_fast_load() will be skipped. Instead,
wait_event_interruptible() and then credit_entropy_bits() will be called.
If the entropy count for that second seed is large enough, that proceeds
to crng_reseed().
However, both wait_event_interruptible() and crng_reseed() depends
(at least in numa_crng_init()) on workqueues. Therefore, test whether
system_wq is already initialized, which is a sufficient indicator that
workqueue_init_early() has progressed far enough.
If we wind up hitting the !system_wq case, we later want to do what
would have been done there when wqs are up, so set a flag, and do that
work later from the rand_initialize() call.
Reported-by: Ivan T. Ivanov <iivanov@suse.de>
Fixes: 18b915ac6b ("efi/random: Treat EFI_RNG_PROTOCOL output as bootloader randomness")
Cc: stable@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
[Jason: added crng_need_done state and related logic.]
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 009ba8568b upstream.
_extract_crng() does plain loads of crng->init_time and
crng_global_init_time, which causes undefined behavior if
crng_reseed() and RNDRESEEDCRNG modify these corrently.
Use READ_ONCE() and WRITE_ONCE() to make the behavior defined.
Don't fix the race on crng->init_time by protecting it with crng->lock,
since it's not a problem for duplicate reseedings to occur. I.e., the
lockless access with READ_ONCE() is fine.
Fixes: d848e5f8e1 ("random: add new ioctl RNDRESEEDCRNG")
Fixes: e192be9d9a ("random: replace non-blocking pool with a Chacha20-based CRNG")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d73d1e320 upstream.
extract_crng() and crng_backtrack_protect() load crng_node_pool with a
plain load, which causes undefined behavior if do_numa_crng_init()
modifies it concurrently.
Fix this by using READ_ONCE(). Note: as per the previous discussion
https://lore.kernel.org/lkml/20211219025139.31085-1-ebiggers@kernel.org/T/#u,
READ_ONCE() is believed to be sufficient here, and it was requested that
it be used here instead of smp_load_acquire().
Also change do_numa_crng_init() to set crng_node_pool using
cmpxchg_release() instead of mb() + cmpxchg(), as the former is
sufficient here but is more lightweight.
Fixes: 1e7f583af6 ("random: make /dev/urandom scalable for silly userspace programs")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a8737ff06 upstream.
The received data contains the channel the received data is associated
with. If the channel number is bigger than the actual number of
channels assume broken or malicious USB device and shut it down.
This fixes the error found by clang:
| drivers/net/can/usb/gs_usb.c:386:6: error: variable 'dev' is used
| uninitialized whenever 'if' condition is true
| if (hf->channel >= GS_MAX_INTF)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
| drivers/net/can/usb/gs_usb.c:474:10: note: uninitialized use occurs here
| hf, dev->gs_hf_size, gs_usb_receive_bulk_callback,
| ^~~
Link: https://lore.kernel.org/all/20211210091158.408326-1-mkl@pengutronix.de
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c9e143084d upstream.
The runtime PM callback may be called as soon as the runtime PM facility
is enabled and activated. It means that ->suspend() may be called before
we finish probing the device in the ACPI case. Hence, NULL pointer
dereference:
intel-lpss INT34BA:00: IRQ index 0 not found
BUG: kernel NULL pointer dereference, address: 0000000000000030
...
Workqueue: pm pm_runtime_work
RIP: 0010:intel_lpss_suspend+0xb/0x40 [intel_lpss]
To fix this, first try to register the device and only after that enable
runtime PM facility.
Fixes: 4b45efe852 ("mfd: Add support for Intel Sunrisepoint LPSS devices")
Reported-by: Orlando Chamberlain <redecorating@protonmail.com>
Reported-by: Aditya Garg <gargaditya08@live.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Aditya Garg <gargaditya08@live.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211101190008.86473-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 710ad98c36 upstream.
Laurent reported that they have seen a significant amount of TCP retransmissions
at high throughput from applications residing in network namespaces talking to
the outside world via veths. The drops were seen on the qdisc layer (fq_codel,
as per systemd default) of the phys device such as ena or virtio_net due to all
traffic hitting a _single_ TX queue _despite_ multi-queue device. (Note that the
setup was _not_ using XDP on veths as the issue is generic.)
More specifically, after edbea92202 ("veth: Store queue_mapping independently
of XDP prog presence") which made it all the way back to v4.19.184+,
skb_record_rx_queue() would set skb->queue_mapping to 1 (given 1 RX and 1 TX
queue by default for veths) instead of leaving at 0.
This is eventually retained and callbacks like ena_select_queue() will also pick
single queue via netdev_core_pick_tx()'s ndo_select_queue() once all the traffic
is forwarded to that device via upper stack or other means. Similarly, for others
not implementing ndo_select_queue() if XPS is disabled, netdev_pick_tx() might
call into the skb_tx_hash() and check for prior skb_rx_queue_recorded() as well.
In general, it is a _bad_ idea for virtual devices like veth to mess around with
queue selection [by default]. Given dev->real_num_tx_queues is by default 1,
the skb->queue_mapping was left untouched, and so prior to edbea92202 the
netdev_core_pick_tx() could do its job upon __dev_queue_xmit() on the phys device.
Unbreak this and restore prior behavior by removing the skb_record_rx_queue()
from veth_xmit() altogether.
If the veth peer has an XDP program attached, then it would return the first RX
queue index in xdp_md->rx_queue_index (unless configured in non-default manner).
However, this is still better than breaking the generic case.
Fixes: edbea92202 ("veth: Store queue_mapping independently of XDP prog presence")
Fixes: 638264dc90 ("veth: Support per queue XDP ring")
Reported-by: Laurent Bernaille <laurent.bernaille@datadoghq.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Cc: Toshiaki Makita <toshiaki.makita1@gmail.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Toshiaki Makita <toshiaki.makita1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a658c929de upstream.
If cfg80211 is providing extraie's for a scanning process then ath11k will
copy that over to the firmware. The extraie.len is a 32 bit value in struct
element_info and describes the amount of bytes for the vendor information
elements.
The WMI_TLV packet is having a special WMI_TAG_ARRAY_BYTE section. This
section can have a (payload) length up to 65535 bytes because the
WMI_TLV_LEN can store up to 16 bits. The code was missing such a check and
could have created a scan request which cannot be parsed correctly by the
firmware.
But the bigger problem was the allocation of the buffer. It has to align
the TLV sections by 4 bytes. But the code was using an u8 to store the
newly calculated length of this section (with alignment). And the new
calculated length was then used to allocate the skbuff. But the actual code
to copy in the data is using the extraie.len and not the calculated
"aligned" length.
The length of extraie with IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS enabled
was 264 bytes during tests with a QCA Milan card. But it only allocated 8
bytes (264 bytes % 256) for it. As consequence, the code to memcpy the
extraie into the skb was then just overwriting data after skb->end. Things
like shinfo were therefore corrupted. This could usually be seen by a crash
in skb_zcopy_clear which tried to call a ubuf_info callback (using a bogus
address).
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-02892.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Cc: stable@vger.kernel.org
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211207142913.1734635-1-sven@narfation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d7d4c0793 upstream.
When the USB core code for getting root-hub status reports was
originally written, it was assumed that the hub driver would be its
only caller. But this isn't true now; user programs can use usbfs to
communicate with root hubs and get status reports. When they do this,
they may use a transfer_buffer that is smaller than the data returned
by the HCD, which will lead to a buffer overflow error when
usb_hcd_poll_rh_status() tries to store the status data. This was
discovered by syzbot:
BUG: KASAN: slab-out-of-bounds in memcpy include/linux/fortify-string.h:225 [inline]
BUG: KASAN: slab-out-of-bounds in usb_hcd_poll_rh_status+0x5f4/0x780 drivers/usb/core/hcd.c:776
Write of size 2 at addr ffff88801da403c0 by task syz-executor133/4062
This patch fixes the bug by reducing the amount of status data if it
won't fit in the transfer_buffer. If some data gets discarded then
the URB's completion status is set to -EOVERFLOW rather than 0, to let
the user know what happened.
Reported-and-tested-by: syzbot+3ae6a2b06f131ab9849f@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Yc+3UIQJ2STbxNua@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f663729bb upstream.
Bugzilla #213839 reports a 7-port hub that doesn't work properly when
devices are plugged into some of the ports; the kernel goes into an
unending disconnect/reinitialize loop as shown in the bug report.
This "7-port hub" comprises two four-port hubs with one plugged into
the other; the failures occur when a device is plugged into one of the
downstream hub's ports. (These hubs have other problems too. For
example, they bill themselves as USB-2.0 compliant but they only run
at full speed.)
It turns out that the failures are caused by bugs in both the kernel
and the hub. The hub's bug is that it reports a different
bmAttributes value in its configuration descriptor following a remote
wakeup (0xe0 before, 0xc0 after -- the wakeup-support bit has
changed).
The kernel's bug is inside the hub driver's resume handler. When
hub_activate() sees that one of the hub's downstream ports got a
wakeup request from a child device, it notes this fact by setting the
corresponding bit in the hub->change_bits variable. But this variable
is meant for connection changes, not wakeup events; setting it causes
the driver to believe the downstream port has been disconnected and
then connected again (in addition to having received a wakeup
request).
Because of this, the hub driver then tries to check whether the device
currently plugged into the downstream port is the same as the device
that had been attached there before. Normally this check succeeds and
wakeup handling continues with no harm done (which is why the bug
remained undetected until now). But with these dodgy hubs, the check
fails because the config descriptor has changed. This causes the hub
driver to reinitialize the child device, leading to the
disconnect/reinitialize loop described in the bug report.
The proper way to note reception of a downstream wakeup request is
to set a bit in the hub->event_bits variable instead of
hub->change_bits. That way the hub driver will realize that something
has happened to the port but will not think the port and child device
have been disconnected. This patch makes that change.
Cc: <stable@vger.kernel.org>
Tested-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YdCw7nSfWYPKWQoD@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5e6fa7a12 upstream.
Add the missing bulk-out endpoint sanity check to probe() to avoid
division by zero in bfusb_send_frame() in case a malicious device has
broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4f ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ no upstream commit given implicitly fixed through the larger refactoring
in c25b2ae136 ]
While auditing some other code, I noticed missing checks inside the pointer
arithmetic simulation, more specifically, adjust_ptr_min_max_vals(). Several
*_OR_NULL types are not rejected whereas they are _required_ to be rejected
given the expectation is that they get promoted into a 'real' pointer type
for the success case, that is, after an explicit != NULL check.
One case which stands out and is accessible from unprivileged (iff enabled
given disabled by default) is BPF ring buffer. From crafting a PoC, the NULL
check can be bypassed through an offset, and its id marking will then lead
to promotion of mem_or_null to a mem type.
bpf_ringbuf_reserve() helper can trigger this case through passing of reserved
flags, for example.
func#0 @0
0: R1=ctx(id=0,off=0,imm=0) R10=fp0
0: (7a) *(u64 *)(r10 -8) = 0
1: R1=ctx(id=0,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm
1: (18) r1 = 0x0
3: R1_w=map_ptr(id=0,off=0,ks=0,vs=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm
3: (b7) r2 = 8
4: R1_w=map_ptr(id=0,off=0,ks=0,vs=0,imm=0) R2_w=invP8 R10=fp0 fp-8_w=mmmmmmmm
4: (b7) r3 = 0
5: R1_w=map_ptr(id=0,off=0,ks=0,vs=0,imm=0) R2_w=invP8 R3_w=invP0 R10=fp0 fp-8_w=mmmmmmmm
5: (85) call bpf_ringbuf_reserve#131
6: R0_w=mem_or_null(id=2,ref_obj_id=2,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm refs=2
6: (bf) r6 = r0
7: R0_w=mem_or_null(id=2,ref_obj_id=2,off=0,imm=0) R6_w=mem_or_null(id=2,ref_obj_id=2,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm refs=2
7: (07) r0 += 1
8: R0_w=mem_or_null(id=2,ref_obj_id=2,off=1,imm=0) R6_w=mem_or_null(id=2,ref_obj_id=2,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm refs=2
8: (15) if r0 == 0x0 goto pc+4
R0_w=mem(id=0,ref_obj_id=0,off=0,imm=0) R6_w=mem(id=0,ref_obj_id=2,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm refs=2
9: R0_w=mem(id=0,ref_obj_id=0,off=0,imm=0) R6_w=mem(id=0,ref_obj_id=2,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm refs=2
9: (62) *(u32 *)(r6 +0) = 0
R0_w=mem(id=0,ref_obj_id=0,off=0,imm=0) R6_w=mem(id=0,ref_obj_id=2,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm refs=2
10: R0_w=mem(id=0,ref_obj_id=0,off=0,imm=0) R6_w=mem(id=0,ref_obj_id=2,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm refs=2
10: (bf) r1 = r6
11: R0_w=mem(id=0,ref_obj_id=0,off=0,imm=0) R1_w=mem(id=0,ref_obj_id=2,off=0,imm=0) R6_w=mem(id=0,ref_obj_id=2,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm refs=2
11: (b7) r2 = 0
12: R0_w=mem(id=0,ref_obj_id=0,off=0,imm=0) R1_w=mem(id=0,ref_obj_id=2,off=0,imm=0) R2_w=invP0 R6_w=mem(id=0,ref_obj_id=2,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm refs=2
12: (85) call bpf_ringbuf_submit#132
13: R6=invP(id=0) R10=fp0 fp-8=mmmmmmmm
13: (b7) r0 = 0
14: R0_w=invP0 R6=invP(id=0) R10=fp0 fp-8=mmmmmmmm
14: (95) exit
from 8 to 13: safe
processed 15 insns (limit 1000000) max_states_per_insn 0 total_states 1 peak_states 1 mark_read 0
OK
All three commits, that is b121b341e5 ("bpf: Add PTR_TO_BTF_ID_OR_NULL support"),
457f44363a ("bpf: Implement BPF ring buffer and verifier support for it"), and the
afbf21dce6 ("bpf: Support readonly/readwrite buffers in verifier") suffer the same
cause and their *_OR_NULL type pendants must be rejected in adjust_ptr_min_max_vals().
Make the test more robust by reusing reg_type_may_be_null() helper such that we catch
all *_OR_NULL types we have today and in future.
Note that pointer arithmetic on PTR_TO_BTF_ID, PTR_TO_RDONLY_BUF, and PTR_TO_RDWR_BUF
is generally allowed.
Fixes: b121b341e5 ("bpf: Add PTR_TO_BTF_ID_OR_NULL support")
Fixes: 457f44363a ("bpf: Implement BPF ring buffer and verifier support for it")
Fixes: afbf21dce6 ("bpf: Support readonly/readwrite buffers in verifier")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07edfece8b upstream.
At CPU-hotplug time, unbind_worker() may preempt a worker while it is
waking up. In that case the following scenario can happen:
unbind_workers() wq_worker_running()
-------------- -------------------
if (!(worker->flags & WORKER_NOT_RUNNING))
//PREEMPTED by unbind_workers
worker->flags |= WORKER_UNBOUND;
[...]
atomic_set(&pool->nr_running, 0);
//resume to worker
atomic_inc(&worker->pool->nr_running);
After unbind_worker() resets pool->nr_running, the value is expected to
remain 0 until the pool ever gets rebound in case cpu_up() is called on
the target CPU in the future. But here the race leaves pool->nr_running
with a value of 1, triggering the following warning when the worker goes
idle:
WARNING: CPU: 3 PID: 34 at kernel/workqueue.c:1823 worker_enter_idle+0x95/0xc0
Modules linked in:
CPU: 3 PID: 34 Comm: kworker/3:0 Not tainted 5.16.0-rc1+ #34
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba527-rebuilt.opensuse.org 04/01/2014
Workqueue: 0x0 (rcu_par_gp)
RIP: 0010:worker_enter_idle+0x95/0xc0
Code: 04 85 f8 ff ff ff 39 c1 7f 09 48 8b 43 50 48 85 c0 74 1b 83 e2 04 75 99 8b 43 34 39 43 30 75 91 8b 83 00 03 00 00 85 c0 74 87 <0f> 0b 5b c3 48 8b 35 70 f1 37 01 48 8d 7b 48 48 81 c6 e0 93 0
RSP: 0000:ffff9b7680277ed0 EFLAGS: 00010086
RAX: 00000000ffffffff RBX: ffff93465eae9c00 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffff9346418a0000 RDI: ffff934641057140
RBP: ffff934641057170 R08: 0000000000000001 R09: ffff9346418a0080
R10: ffff9b768027fdf0 R11: 0000000000002400 R12: ffff93465eae9c20
R13: ffff93465eae9c20 R14: ffff93465eae9c70 R15: ffff934641057140
FS: 0000000000000000(0000) GS:ffff93465eac0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 000000001cc0c000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
worker_thread+0x89/0x3d0
? process_one_work+0x400/0x400
kthread+0x162/0x190
? set_kthread_struct+0x40/0x40
ret_from_fork+0x22/0x30
</TASK>
Also due to this incorrect "nr_running == 1", further queued work may
end up not being served, because no worker is awaken at work insert time.
This raises rcutorture writer stalls for example.
Fix this with disabling preemption in the right place in
wq_worker_running().
It's worth noting that if the worker migrates and runs concurrently with
unbind_workers(), it is guaranteed to see the WORKER_UNBOUND flag update
due to set_cpus_allowed_ptr() acquiring/releasing rq->lock.
Fixes: 6d25be5782 ("sched/core, workqueues: Distangle worker accounting from rq lock")
Reviewed-by: Lai Jiangshan <jiangshanlai@gmail.com>
Tested-by: Paul E. McKenney <paulmck@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Daniel Bristot de Oliveira <bristot@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move from only supporting the default of pre-multiplied
alpha to supporting user specified blend mode using the
standardised property.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
We are using mode->crt_clock here which is filled by drm_mode_set_crtcinfo()
which is called right after .mode_valid.
Use mode->clock which is valid here.
Fixes: 624d93a4f0 ("drm/vc4: hdmi: Move clock calculation into its own function")
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Still under investigation, but the conditions under which the HVS
will accept values written to the gamma PWL are not straightforward.
Disable gamma on HVS5 again until it can be resolved to avoid
gamma being enabled with an incorrect table.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Replace the cfi directives with the UNWIND equivalents. This prevents
the .eh_frame section from being created, eliminating the warnings.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
With the automatic VL805 support being removed from the standard
CM4 dtb (since most CM4 carriers don't have a VL805), retain support
on those that do by creating a "vl805" overlay that restores the
deleted "usb@0,0" node.
The "vl805" overlay will be loaded automatically (after an upcoming
firmware update) on CM4 boards where the EEPROM config includes the
setting VL805=1.
See: https://forums.raspberrypi.com/viewtopic.php?t=326088
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
commit cf73ed894e upstream.
Since irq request is the last thing in the driver probe, it happens
later than the input device registration. This means that there is a
small time window where if the open method is called the driver will
attempt to enable not yet available irq.
Fix that by moving the irq request before the input device registration.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Fixes: 26822652c8 ("Input: add zinitix touchscreen driver")
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20220106072840.36851-2-nikita@trvn.ru
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8b5fdfc57c ]
As we build for mips, we meet following error. l1_init error with
multiple definition. Some architecture devices usually marked with
l1, l2, lxx as the start-up phase. so we change the mISDN function
names, align with Isdnl2_xxx.
mips-linux-gnu-ld: drivers/isdn/mISDN/layer1.o: in function `l1_init':
(.text+0x890): multiple definition of `l1_init'; \
arch/mips/kernel/bmips_5xxx_init.o:(.text+0xf0): first defined here
make[1]: *** [home/mips/kernel-build/linux/Makefile:1161: vmlinux] Error 1
Signed-off-by: wolfgang huang <huangjinhui@kylinos.cn>
Reported-by: k2ci <kernel-bot@kylinos.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1833c3964 ]
The "__ip6_tnl_parm" struct was left uninitialized causing an invalid
load of random data when the "__ip6_tnl_parm" struct was used elsewhere.
As an example, in the function "ip6_tnl_xmit_ctl()", it tries to access
the "collect_md" member. With "__ip6_tnl_parm" being uninitialized and
containing random data, the UBSAN detected that "collect_md" held a
non-boolean value.
The UBSAN issue is as follows:
===============================================================
UBSAN: invalid-load in net/ipv6/ip6_tunnel.c:1025:14
load of value 30 is not a valid value for type '_Bool'
CPU: 1 PID: 228 Comm: kworker/1:3 Not tainted 5.16.0-rc4+ #8
Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
Workqueue: ipv6_addrconf addrconf_dad_work
Call Trace:
<TASK>
dump_stack_lvl+0x44/0x57
ubsan_epilogue+0x5/0x40
__ubsan_handle_load_invalid_value+0x66/0x70
? __cpuhp_setup_state+0x1d3/0x210
ip6_tnl_xmit_ctl.cold.52+0x2c/0x6f [ip6_tunnel]
vti6_tnl_xmit+0x79c/0x1e96 [ip6_vti]
? lock_is_held_type+0xd9/0x130
? vti6_rcv+0x100/0x100 [ip6_vti]
? lock_is_held_type+0xd9/0x130
? rcu_read_lock_bh_held+0xc0/0xc0
? lock_acquired+0x262/0xb10
dev_hard_start_xmit+0x1e6/0x820
__dev_queue_xmit+0x2079/0x3340
? mark_lock.part.52+0xf7/0x1050
? netdev_core_pick_tx+0x290/0x290
? kvm_clock_read+0x14/0x30
? kvm_sched_clock_read+0x5/0x10
? sched_clock_cpu+0x15/0x200
? find_held_lock+0x3a/0x1c0
? lock_release+0x42f/0xc90
? lock_downgrade+0x6b0/0x6b0
? mark_held_locks+0xb7/0x120
? neigh_connected_output+0x31f/0x470
? lockdep_hardirqs_on+0x79/0x100
? neigh_connected_output+0x31f/0x470
? ip6_finish_output2+0x9b0/0x1d90
? rcu_read_lock_bh_held+0x62/0xc0
? ip6_finish_output2+0x9b0/0x1d90
ip6_finish_output2+0x9b0/0x1d90
? ip6_append_data+0x330/0x330
? ip6_mtu+0x166/0x370
? __ip6_finish_output+0x1ad/0xfb0
? nf_hook_slow+0xa6/0x170
ip6_output+0x1fb/0x710
? nf_hook.constprop.32+0x317/0x430
? ip6_finish_output+0x180/0x180
? __ip6_finish_output+0xfb0/0xfb0
? lock_is_held_type+0xd9/0x130
ndisc_send_skb+0xb33/0x1590
? __sk_mem_raise_allocated+0x11cf/0x1560
? dst_output+0x4a0/0x4a0
? ndisc_send_rs+0x432/0x610
addrconf_dad_completed+0x30c/0xbb0
? addrconf_rs_timer+0x650/0x650
? addrconf_dad_work+0x73c/0x10e0
addrconf_dad_work+0x73c/0x10e0
? addrconf_dad_completed+0xbb0/0xbb0
? rcu_read_lock_sched_held+0xaf/0xe0
? rcu_read_lock_bh_held+0xc0/0xc0
process_one_work+0x97b/0x1740
? pwq_dec_nr_in_flight+0x270/0x270
worker_thread+0x87/0xbf0
? process_one_work+0x1740/0x1740
kthread+0x3ac/0x490
? set_kthread_struct+0x100/0x100
ret_from_fork+0x22/0x30
</TASK>
===============================================================
The solution is to initialize "__ip6_tnl_parm" struct to zeros in the
"vti6_siocdevprivate()" function.
Signed-off-by: William Zhao <wizhao@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 80211be1b9 upstream.
Instead of one shot run of ADC at beginning of charging, run continuous
conversion to ensure that all charging-related values are monitored
properly (input voltage, input current, themperature etc.).
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29262e1f77 upstream.
Hytera makes a range of digital (DMR) radios. These radios can be
programmed to a allow a computer to control them over Ethernet over USB,
either using NCM or RNDIS.
This commit adds support for RNDIS for Hytera radios. I tested with a
Hytera PD785 and a Hytera MD785G. When these radios are programmed to
set up a Radio to PC Network using RNDIS, an USB interface will be added
with class 2 (Communications), subclass 2 (Abstract Modem Control) and
an interface protocol of 255 ("vendor specific" - lsusb even hints "MSFT
RNDIS?").
This patch is similar to the solution of this StackOverflow user, but
that only works for the Hytera MD785:
https://stackoverflow.com/a/53550858
To use the "Radio to PC Network" functionality of Hytera DMR radios, the
radios need to be programmed correctly in CPS (Hytera's Customer
Programming Software). "Forward to PC" should be checked in "Network"
(under "General Setting" in "Conventional") and the "USB Network
Communication Protocol" should be set to RNDIS.
Signed-off-by: Thomas Toye <thomas@toye.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 644106cdb8 upstream.
A new commit in LLVM causes an error on the use of 'long double' when
'-mno-x87' is used, which the kernel does through an alias,
'-mno-80387' (see the LLVM commit below for more details around why it
does this).
drivers/power/reset/ltc2952-poweroff.c:162:28: error: expression requires 'long double' type support, but target 'x86_64-unknown-linux-gnu' does not support it
data->wde_interval = 300L * 1E6L;
^
drivers/power/reset/ltc2952-poweroff.c:162:21: error: expression requires 'long double' type support, but target 'x86_64-unknown-linux-gnu' does not support it
data->wde_interval = 300L * 1E6L;
^
drivers/power/reset/ltc2952-poweroff.c:163:41: error: expression requires 'long double' type support, but target 'x86_64-unknown-linux-gnu' does not support it
data->trigger_delay = ktime_set(2, 500L*1E6L);
^
3 errors generated.
This happens due to the use of a 'long double' literal. The 'E6' part of
'1E6L' causes the literal to be a 'double' then the 'L' suffix promotes
it to 'long double'.
There is no visible reason for floating point values in this driver, as
the values are only assigned to integer types. Use NSEC_PER_MSEC, which
is the same integer value as '1E6L', to avoid changing functionality but
fix the error.
Fixes: 6647156c00 ("power: reset: add LTC2952 poweroff driver")
Link: https://github.com/ClangBuiltLinux/linux/issues/1497
Link: a8083d42b1
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5055dc0348 upstream.
The role of ena_calc_max_io_queue_num() is to return the number
of queues supported by the device, which means the return value
should be >=0.
The function that calls ena_calc_max_io_queue_num(), checks
the return value. If it is 0, it means the device reported
it supports 0 IO queues. This case is considered an error
and is handled by the calling function accordingly.
However the current implementation of ena_calc_max_io_queue_num()
is wrong, since when it detects the device supports 0 IO queues,
it returns -EFAULT.
In such a case the calling function doesn't detect the error,
and therefore doesn't handle it.
This commit changes ena_calc_max_io_queue_num() to return 0
in case the device reported it supports 0 queues, allowing the
calling function to properly handle the error case.
Fixes: 736ce3f414 ("net: ena: make ethtool -l show correct max number of queues")
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c255a34e02 upstream.
ena_com_tx_comp_req_id_get() checks the req_id of a received completion,
and if it is out of bounds returns -EINVAL. This is a sign that
something is wrong with the device and it needs to be reset.
The current code does not reset the device in this case, which leaves
the driver in an undefined state, where this completion is not properly
handled.
This commit adds a call to handle_invalid_req_id() in ena_clean_tx_irq()
and ena_clean_xdp_irq() which resets the device to fix the issue.
This commit also removes unnecessary request id checks from
validate_tx_req_id() and validate_xdp_req_id(). This check is unneeded
because it was already performed in ena_com_tx_comp_req_id_get(), which
is called right before these functions.
Fixes: 548c4940b9 ("net: ena: Implement XDP_TX action")
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d18a07897 upstream.
tx_queue_len can be set to ~0U, we need to be more
careful about overflows.
__fls(0) is undefined, as this report shows:
UBSAN: shift-out-of-bounds in net/sched/sch_qfq.c:1430:24
shift exponent 51770272 is too large for 32-bit type 'int'
CPU: 0 PID: 25574 Comm: syz-executor.0 Not tainted 5.16.0-rc7-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x201/0x2d8 lib/dump_stack.c:106
ubsan_epilogue lib/ubsan.c:151 [inline]
__ubsan_handle_shift_out_of_bounds+0x494/0x530 lib/ubsan.c:330
qfq_init_qdisc+0x43f/0x450 net/sched/sch_qfq.c:1430
qdisc_create+0x895/0x1430 net/sched/sch_api.c:1253
tc_modify_qdisc+0x9d9/0x1e20 net/sched/sch_api.c:1660
rtnetlink_rcv_msg+0x934/0xe60 net/core/rtnetlink.c:5571
netlink_rcv_skb+0x200/0x470 net/netlink/af_netlink.c:2496
netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
netlink_unicast+0x814/0x9f0 net/netlink/af_netlink.c:1345
netlink_sendmsg+0xaea/0xe60 net/netlink/af_netlink.c:1921
sock_sendmsg_nosec net/socket.c:704 [inline]
sock_sendmsg net/socket.c:724 [inline]
____sys_sendmsg+0x5b9/0x910 net/socket.c:2409
___sys_sendmsg net/socket.c:2463 [inline]
__sys_sendmsg+0x280/0x370 net/socket.c:2492
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
Fixes: 462dbc9101 ("pkt_sched: QFQ Plus: fair-queueing service at DRR cost")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 938f2e0b57 upstream.
The addition of routable multicast TX handling introduced a
bug/regression for packets with a link-local multicast destination:
These packets would be sent to all batman-adv nodes with a multicast
router and to all batman-adv nodes with an old version without multicast
router detection.
This even disregards the batman-adv multicast fanout setting, which can
potentially lead to an unwanted, high number of unicast transmissions or
even congestion.
Fixing this by avoiding to send link-local multicast packets to nodes in
the multicast router list.
Fixes: 11d458c1cb ("batman-adv: mcast: apply optimizations for routable packets, too")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8bda81a4d4 upstream.
lwtunnel_valid_encap_type_attr is used to validate encap attributes
within a multipath route. Add length validation checking to the type.
lwtunnel_valid_encap_type_attr is called converting attributes to
fib{6,}_config struct which means it is used before fib_get_nhs,
ip6_route_multipath_add, and ip6_route_multipath_del - other
locations that use rtnh_ok and then nla_get_u16 on RTA_ENCAP_TYPE
attribute.
Fixes: 9ed59592e3 ("lwtunnel: fix autoload of lwt modules")
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4619bcf913 upstream.
Commit referenced in the Fixes tag used nla_memcpy for RTA_GATEWAY as
does the current nla_get_in6_addr. nla_memcpy protects against accessing
memory greater than what is in the attribute, but there is no check
requiring the attribute to have an IPv6 address. Add it.
Fixes: 51ebd31815 ("ipv6: add support of equal cost multipath (ECMP)")
Signed-off-by: David Ahern <dsahern@kernel.org>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0daf5cb217 upstream.
There's another compilation fail (first here [1]) reported by kernel
test robot for W=1 clang build:
>> samples/ftrace/ftrace-direct-multi-modify.c:7:6: warning: no previous
prototype for function 'my_direct_func1' [-Wmissing-prototypes]
void my_direct_func1(unsigned long ip)
Direct functions in ftrace direct sample modules need to have prototypes
defined. They are already global in order to be visible for the inline
assembly, so there's no problem.
The kernel test robot reported just error for ftrace-direct-multi-modify,
but I got same errors also for the rest of the modules touched by this patch.
[1] 67d4f6e3bf ftrace/samples: Add missing prototype for my_direct_func
Link: https://lkml.kernel.org/r/20211219135317.212430-1-jolsa@kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Fixes: e1067a07cf ("ftrace/samples: Add module to test multi direct modify interface")
Fixes: ae0cc3b7e7 ("ftrace/samples: Add a sample module that implements modify_ftrace_direct()")
Fixes: 156473a0ff ("ftrace: Add another example of register_ftrace_direct() use case")
Fixes: b06457c83a ("ftrace: Add sample module that uses register_ftrace_direct()")
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e738451d78 upstream.
There was a wrong queues representation in sysfs during
driver's reinitialization in case of online cpus number is
less than combined queues. It was caused by stopped
NetworkManager, which is responsible for calling vsi_open
function during driver's initialization.
In specific situation (ex. 12 cpus online) there were 16 queues
in /sys/class/net/<iface>/queues. In case of modifying queues with
value higher, than number of online cpus, then it caused write
errors and other errors.
Add updating of sysfs's queues representation during driver
initialization.
Fixes: 41c445ff0f ("i40e: main driver core")
Signed-off-by: Lukasz Cieplicki <lukaszx.cieplicki@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40feded8a2 upstream.
When loading the i40e driver, it prints a message like: 'The driver for the
device detected a newer version of the NVM image v1.x than expected v1.y.
Please install the most recent version of the network driver.' This is
misleading as the driver is working as expected.
Fix that by removing the second part of message and changing it from
dev_info to dev_dbg.
Fixes: 4fb29bddb5 ("i40e: The driver now prints the API version in error message")
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68a18ad713 upstream.
Clang static analysis reports this warnings
mlme.c:5332:7: warning: Branch condition evaluates to a
garbage value
have_higher_than_11mbit)
^~~~~~~~~~~~~~~~~~~~~~~
have_higher_than_11mbit is only set to true some of the time in
ieee80211_get_rates() but is checked all of the time. So
have_higher_than_11mbit needs to be initialized to false.
Fixes: 5d6a1b069b ("mac80211: set basic rates earlier")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20211223162848.3243702-1-trix@redhat.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3087a6f36e upstream.
This code used to copy in an unsigned long worth of data before
the sockptr_t conversion, so restore that.
Fixes: a7b75c5a8c ("net: pass a sockptr_t into ->setsockopt")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b35a0f4dd5 upstream.
If dst->is_global field is not set, the GRH fields are not cleared
and the following infoleak is reported.
=====================================================
BUG: KMSAN: kernel-infoleak in instrument_copy_to_user include/linux/instrumented.h:121 [inline]
BUG: KMSAN: kernel-infoleak in _copy_to_user+0x1c9/0x270 lib/usercopy.c:33
instrument_copy_to_user include/linux/instrumented.h:121 [inline]
_copy_to_user+0x1c9/0x270 lib/usercopy.c:33
copy_to_user include/linux/uaccess.h:209 [inline]
ucma_init_qp_attr+0x8c7/0xb10 drivers/infiniband/core/ucma.c:1242
ucma_write+0x637/0x6c0 drivers/infiniband/core/ucma.c:1732
vfs_write+0x8ce/0x2030 fs/read_write.c:588
ksys_write+0x28b/0x510 fs/read_write.c:643
__do_sys_write fs/read_write.c:655 [inline]
__se_sys_write fs/read_write.c:652 [inline]
__ia32_sys_write+0xdb/0x120 fs/read_write.c:652
do_syscall_32_irqs_on arch/x86/entry/common.c:114 [inline]
__do_fast_syscall_32+0x96/0xf0 arch/x86/entry/common.c:180
do_fast_syscall_32+0x34/0x70 arch/x86/entry/common.c:205
do_SYSENTER_32+0x1b/0x20 arch/x86/entry/common.c:248
entry_SYSENTER_compat_after_hwframe+0x4d/0x5c
Local variable resp created at:
ucma_init_qp_attr+0xa4/0xb10 drivers/infiniband/core/ucma.c:1214
ucma_write+0x637/0x6c0 drivers/infiniband/core/ucma.c:1732
Bytes 40-59 of 144 are uninitialized
Memory access of size 144 starts at ffff888167523b00
Data copied to user address 0000000020000100
CPU: 1 PID: 25910 Comm: syz-executor.1 Not tainted 5.16.0-rc5-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
=====================================================
Fixes: 4ba66093bd ("IB/core: Check for global flag when using ah_attr")
Link: https://lore.kernel.org/r/0e9dd51f93410b7b2f4f5562f52befc878b71afa.1641298868.git.leonro@nvidia.com
Reported-by: syzbot+6d532fa8f9463da290bc@syzkaller.appspotmail.com
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b712941c80 upstream.
In the absence of this validation, if the user requests to
configure queues more than the enabled queues, it results in
sending the requested number of queues to the kernel stack
(due to the asynchronous nature of VF response), in which
case the stack might pick a queue to transmit that is not
enabled and result in Tx hang. Fix this bug by
limiting the total number of queues allocated for VF to
active queues of VF.
Fixes: d5b33d0244 ("i40evf: add ndo_setup_tc callback to i40evf")
Signed-off-by: Ashwin Vijayavel <ashwin.vijayavel@intel.com>
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 01cbf50877 upstream.
Hide i40e opcode information sent during response to VF in case when
untrusted VF tried to change MAC on the VF interface.
This is implemented by adding an additional parameter 'hide' to the
response sent to VF function that hides the display of error
information, but forwards the error code to VF.
Previously it was not possible to send response with some error code
to VF without displaying opcode information.
Fixes: 5c3c48ac6b ("i40e: implement virtual device interface")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Reviewed-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 754e438235 upstream.
Alexander reported a use of uninitialized value in
atusb_set_extended_addr(), that is caused by reading 0 bytes via
usb_control_msg().
Fix it by validating if the number of bytes transferred is actually
correct, since usb_control_msg() may read less bytes, than was requested
by caller.
Fail log:
BUG: KASAN: uninit-cmp in ieee802154_is_valid_extended_unicast_addr include/linux/ieee802154.h:310 [inline]
BUG: KASAN: uninit-cmp in atusb_set_extended_addr drivers/net/ieee802154/atusb.c:1000 [inline]
BUG: KASAN: uninit-cmp in atusb_probe.cold+0x29f/0x14db drivers/net/ieee802154/atusb.c:1056
Uninit value used in comparison: 311daa649a2003bd stack handle: 000000009a2003bd
ieee802154_is_valid_extended_unicast_addr include/linux/ieee802154.h:310 [inline]
atusb_set_extended_addr drivers/net/ieee802154/atusb.c:1000 [inline]
atusb_probe.cold+0x29f/0x14db drivers/net/ieee802154/atusb.c:1056
usb_probe_interface+0x314/0x7f0 drivers/usb/core/driver.c:396
Fixes: 7490b008d1 ("ieee802154: add support for atusb transceiver")
Reported-by: Alexander Potapenko <glider@google.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/20220104182806.7188-1-paskripkin@gmail.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 823e670f7e upstream.
With the new osnoise tracer, we are seeing the below splat:
Kernel attempted to read user page (c7d880000) - exploit attempt? (uid: 0)
BUG: Unable to handle kernel data access on read at 0xc7d880000
Faulting instruction address: 0xc0000000002ffa10
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Radix SMP NR_CPUS=2048 NUMA pSeries
...
NIP [c0000000002ffa10] __trace_array_vprintk.part.0+0x70/0x2f0
LR [c0000000002ff9fc] __trace_array_vprintk.part.0+0x5c/0x2f0
Call Trace:
[c0000008bdd73b80] [c0000000001c49cc] put_prev_task_fair+0x3c/0x60 (unreliable)
[c0000008bdd73be0] [c000000000301430] trace_array_printk_buf+0x70/0x90
[c0000008bdd73c00] [c0000000003178b0] trace_sched_switch_callback+0x250/0x290
[c0000008bdd73c90] [c000000000e70d60] __schedule+0x410/0x710
[c0000008bdd73d40] [c000000000e710c0] schedule+0x60/0x130
[c0000008bdd73d70] [c000000000030614] interrupt_exit_user_prepare_main+0x264/0x270
[c0000008bdd73de0] [c000000000030a70] syscall_exit_prepare+0x150/0x180
[c0000008bdd73e10] [c00000000000c174] system_call_vectored_common+0xf4/0x278
osnoise tracer on ppc64le is triggering osnoise_taint() for negative
duration in get_int_safe_duration() called from
trace_sched_switch_callback()->thread_exit().
The problem though is that the check for a valid trace_percpu_buffer is
incorrect in get_trace_buf(). The check is being done after calculating
the pointer for the current cpu, rather than on the main percpu pointer.
Fix the check to be against trace_percpu_buffer.
Link: https://lkml.kernel.org/r/a920e4272e0b0635cf20c444707cbce1b2c8973d.1640255304.git.naveen.n.rao@linux.vnet.ibm.com
Cc: stable@vger.kernel.org
Fixes: e2ace00117 ("tracing: Choose static tp_printk buffer by explicit nesting count")
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5c0042200 upstream.
As Yi Zhuang reported in bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=214299
There is potential deadlock during quota data flush as below:
Thread A: Thread B:
f2fs_dquot_acquire
down_read(&sbi->quota_sem)
f2fs_write_checkpoint
block_operations
f2fs_look_all
down_write(&sbi->cp_rwsem)
f2fs_quota_write
f2fs_write_begin
__do_map_lock
f2fs_lock_op
down_read(&sbi->cp_rwsem)
__need_flush_qutoa
down_write(&sbi->quota_sem)
This patch changes block_operations() to use trylock, if it fails,
it means there is potential quota data updater, in this condition,
let's flush quota data first and then trylock again to check dirty
status of quota data.
The side effect is: in heavy race condition (e.g. multi quota data
upaters vs quota data flusher), it may decrease the probability of
synchronizing quota data successfully in checkpoint() due to limited
retry time of quota flush.
Reported-by: Yi Zhuang <zhuangyi1@huawei.com>
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To allow for the cases where a simple panel does have a GPIO
controlled backlight. Defaults to having no backlight defined.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Use GitHubs issue form for bug reports.
- modern look
- user don't need to mess with given markdown parts while filling the issue template
Setup config.yml for general questions and problems with the Raspbian distribution packages.
The driver did allow the exposure to go up to VTS - 4 lines,
but this would produce a visible line on 1280x800, and a stall of
the sensor at 640x480.
Whilst it appears to work with a difference of 5, the datasheet states
there should be at least 25 lines difference between VTS and exposure,
so use that value.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
commit 08389d8882 upstream.
Add a kconfig knob which allows for unprivileged bpf to be disabled by default.
If set, the knob sets /proc/sys/kernel/unprivileged_bpf_disabled to value of 2.
This still allows a transition of 2 -> {0,1} through an admin. Similarly,
this also still keeps 1 -> {1} behavior intact, so that once set to permanently
disabled, it cannot be undone aside from a reboot.
We've also added extra2 with max of 2 for the procfs handler, so that an admin
still has a chance to toggle between 0 <-> 2.
Either way, as an additional alternative, applications can make use of CAP_BPF
that we added a while ago.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/74ec548079189e4e4dffaeb42b8987bb3c852eee.1620765074.git.daniel@iogearbox.net
Cc: Salvatore Bonaccorso <carnil@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e22e45fc9e upstream.
A real world panic issue was found as follow in Linux 5.4.
BUG: unable to handle page fault for address: ffffde49a863de28
PGD 7e6fe62067 P4D 7e6fe62067 PUD 7e6fe63067 PMD f51e064067 PTE 0
RIP: 0010:tw_timer_handler+0x20/0x40
Call Trace:
<IRQ>
call_timer_fn+0x2b/0x120
run_timer_softirq+0x1ef/0x450
__do_softirq+0x10d/0x2b8
irq_exit+0xc7/0xd0
smp_apic_timer_interrupt+0x68/0x120
apic_timer_interrupt+0xf/0x20
This issue was also reported since 2017 in the thread [1],
unfortunately, the issue was still can be reproduced after fixing
DCCP.
The ipv4_mib_exit_net is called before tcp_sk_exit_batch when a net
namespace is destroyed since tcp_sk_ops is registered befrore
ipv4_mib_ops, which means tcp_sk_ops is in the front of ipv4_mib_ops
in the list of pernet_list. There will be a use-after-free on
net->mib.net_statistics in tw_timer_handler after ipv4_mib_exit_net
if there are some inflight time-wait timers.
This bug is not introduced by commit f2bf415cfe ("mib: add net to
NET_ADD_STATS_BH") since the net_statistics is a global variable
instead of dynamic allocation and freeing. Actually, commit
61a7e26028 ("mib: put net statistics on struct net") introduces
the bug since it put net statistics on struct net and free it when
net namespace is destroyed.
Moving init_ipv4_mibs() to the front of tcp_init() to fix this bug
and replace pr_crit() with panic() since continuing is meaningless
when init_ipv4_mibs() fails.
[1] https://groups.google.com/g/syzkaller/c/p1tn-_Kc6l4/m/smuL_FMAAgAJ?pli=1
Fixes: 61a7e26028 ("mib: put net statistics on struct net")
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Cc: Cong Wang <cong.wang@bytedance.com>
Cc: Fam Zheng <fam.zheng@bytedance.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211228104145.9426-1-songmuchun@bytedance.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 142c779d05 upstream.
The PVSCSI implementation in the VMware hypervisor under specific
configuration ("SCSI Bus Sharing" set to "Physical") returns zero dataLen
in the completion descriptor for READ CAPACITY(16). As a result, the kernel
can not detect proper disk geometry. This can be recognized by the kernel
message:
[ 0.776588] sd 1:0:0:0: [sdb] Sector size 0 reported, assuming 512.
The PVSCSI implementation in QEMU does not set dataLen at all, keeping it
zeroed. This leads to a boot hang as was reported by Shmulik Ladkani.
It is likely that the controller returns the garbage at the end of the
buffer. Residual length should be set by the driver in that case. The SCSI
layer will erase corresponding data. See commit bdb2b8cab4 ("[SCSI] erase
invalid data returned by device") for details.
Commit e662502b3a ("scsi: vmw_pvscsi: Set correct residual data length")
introduced the issue by setting residual length unconditionally, causing
the SCSI layer to erase the useful payload beyond dataLen when this value
is returned as 0.
As a result, considering existing issues in implementations of PVSCSI
controllers, we do not want to call scsi_set_resid() when dataLen ==
0. Calling scsi_set_resid() has no effect if dataLen equals buffer length.
Link: https://lore.kernel.org/lkml/20210824120028.30d9c071@blondie/
Link: https://lore.kernel.org/r/20211220190514.55935-1-amakhalov@vmware.com
Fixes: e662502b3a ("scsi: vmw_pvscsi: Set correct residual data length")
Cc: Matt Wang <wwentao@vmware.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Vishal Bhakta <vbhakta@vmware.com>
Cc: VMware PV-Drivers <pv-drivers@vmware.com>
Cc: James E.J. Bottomley <jejb@linux.ibm.com>
Cc: linux-scsi@vger.kernel.org
Cc: stable@vger.kernel.org
Reported-and-suggested-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Alexey Makhalov <amakhalov@vmware.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cfd0d84ba2 upstream.
In 4.13, commit 74310e06be ("android: binder: Move buffer out of area shared with user space")
fixed a kernel structure visibility issue. As part of that patch,
sizeof(void *) was used as the buffer size for 0-length data payloads so
the driver could detect abusive clients sending 0-length asynchronous
transactions to a server by enforcing limits on async_free_size.
Unfortunately, on the "free" side, the accounting of async_free_space
did not add the sizeof(void *) back. The result was that up to 8-bytes of
async_free_space were leaked on every async transaction of 8-bytes or
less. These small transactions are uncommon, so this accounting issue
has gone undetected for several years.
The fix is to use "buffer_size" (the allocated buffer size) instead of
"size" (the logical buffer size) when updating the async_free_space
during the free operation. These are the same except for this
corner case of asynchronous transactions with payloads < 8 bytes.
Fixes: 74310e06be ("android: binder: Move buffer out of area shared with user space")
Signed-off-by: Todd Kjos <tkjos@google.com>
Cc: stable@vger.kernel.org # 4.14+
Link: https://lore.kernel.org/r/20211220190150.2107077-1-tkjos@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e484409258 upstream.
The Fresco Logic FL1100 controller needs the TRUST_TX_LENGTH quirk like
other Fresco controllers, but should not have the BROKEN_MSI quirks set.
BROKEN_MSI quirk causes issues in detecting usb drives connected to docks
with this FL1100 controller.
The BROKEN_MSI flag was apparently accidentally set together with the
TRUST_TX_LENGTH quirk
Original patch went to stable so this should go there as well.
Fixes: ea0f69d821 ("xhci: Enable trust tx length quirk for Fresco FL11 USB controller")
Cc: stable@vger.kernel.org
cc: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211221112825.54690-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7865173cf upstream.
Play a video on the raven (or PCO, raven2) platform, and then do the S3
test. When resume, the following error will be reported:
amdgpu 0000:02:00.0: [drm:amdgpu_ring_test_helper [amdgpu]] *ERROR* ring
vcn_dec test failed (-110)
[drm:amdgpu_device_ip_resume_phase2 [amdgpu]] *ERROR* resume of IP block
<vcn_v1_0> failed -110
amdgpu 0000:02:00.0: amdgpu: amdgpu_device_ip_resume failed (-110).
PM: dpm_run_callback(): pci_pm_resume+0x0/0x90 returns -110
[why]
When playing the video: The power state flag of the vcn block is set to
POWER_STATE_ON.
When doing suspend: There is no change to the power state flag of the
vcn block, it is still POWER_STATE_ON.
When doing resume: Need to open the power gate of the vcn block and set
the power state flag of the VCN block to POWER_STATE_ON.
But at this time, the power state flag of the vcn block is already
POWER_STATE_ON. The power status flag check in the "8f2cdef drm/amd/pm:
avoid duplicate powergate/ungate setting" patch will return the
amdgpu_dpm_set_powergating_by_smu function directly.
As a result, the gate of the power was not opened, causing the
subsequent ring test to fail.
[how]
In the suspend function of the vcn block, explicitly change the power
state flag of the vcn block to POWER_STATE_OFF.
BugLink: https://gitlab.freedesktop.org/drm/amd/-/issues/1828
Signed-off-by: chen gong <curry.gong@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7175f02c4e upstream.
Replace sa_family_t with __kernel_sa_family_t to fix the following
linux/nfc.h userspace compilation errors:
/usr/include/linux/nfc.h:266:2: error: unknown type name 'sa_family_t'
sa_family_t sa_family;
/usr/include/linux/nfc.h:274:2: error: unknown type name 'sa_family_t'
sa_family_t sa_family;
Fixes: 23b7869c0f ("NFC: add the NFC socket raw protocol")
Fixes: d646960f79 ("NFC: Initial LLCP support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 79b69a8370 upstream.
Fix user-space builds if it includes /usr/include/linux/nfc.h before
some of other headers:
/usr/include/linux/nfc.h:281:9: error: unknown type name ‘size_t’
281 | size_t service_name_len;
| ^~~~~~
Fixes: d646960f79 ("NFC: Initial LLCP support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bb436283e2 ]
Wrong user data may cause warning in i2c_transfer(), ex: zero msgs.
Userspace should not be able to trigger warnings, so this patch adds
validation checks for user data in compact ioctl to prevent reported
warnings
Reported-and-tested-by: syzbot+e417648b303855b91d8a@syzkaller.appspotmail.com
Fixes: 7d5cb45655 ("i2c compat ioctls: move to ->compat_ioctl()")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf2b09fedc ]
The reference taken by 'of_find_device_by_node()' must be released when
not needed anymore.
Add the corresponding 'put_device()' in the and error handling paths.
Fixes: 18a6c85fcc ("fsl/fman: Add FMan Port Support")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92a34ab169 ]
As we can see from the comment of the nla_put() that it could return
-EMSGSIZE if the tailroom of the skb is insufficient.
Therefore, it should be better to check the return value of the
nla_put_u32 and return the error code if error accurs.
Also, there are many other functions have the same problem, and if this
patch is correct, I will commit a new version to fix all.
Fixes: 955dc68cb9 ("net/ncsi: Add generic netlink family")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20211229032118.1706294-1-jiasheng@iscas.ac.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c1952aeaa ]
udpgso_bench_tx call setup_sockaddr() for dest address before
parsing all arguments, if we specify "-p ${dst_port}" after "-D ${dst_ip}",
then ${dst_port} will be ignored, and using default cfg_port 8000.
This will cause test case "multiple GRO socks" failed in udpgro.sh.
Setup sockaddr after parsing all arguments.
Fixes: 3a687bef14 ("selftests: udp gso benchmark")
Signed-off-by: Jianguo Wu <wujianguo@chinatelecom.cn>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/ff620d9f-5b52-06ab-5286-44b945453002@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 992d8a4e38 ]
In case of an error in mlx5e_set_features(), 'netdev->features' must be
updated with the correct state of the device to indicate which features
were updated successfully.
To do that we maintain a copy of 'netdev->features' and update it after
successful feature changes, so we can assign it to back to
'netdev->features' if needed.
However, since not all netdev features are handled by the driver (e.g.
GRO/TSO/etc), some features may not be updated correctly in case of an
error updating another feature.
For example, while requesting to disable TSO (feature which is not
handled by the driver) and enable HW-GRO, if an error occurs during
HW-GRO enable, 'oper_features' will be assigned with 'netdev->features'
and HW-GRO turned off. TSO will remain enabled in such case, which is a
bug.
To solve that, instead of using 'netdev->features' as the baseline of
'oper_features' and changing it on set feature success, use 'features'
instead and update it in case of errors.
Fixes: 75b81ce719 ("net/mlx5e: Don't override netdev features field unless in error flow")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 349d43127d ]
A crash occurs when smc_cdc_tx_handler() tries to access smc_sock
but smc_release() has already freed it.
[ 4570.695099] BUG: unable to handle page fault for address: 000000002eae9e88
[ 4570.696048] #PF: supervisor write access in kernel mode
[ 4570.696728] #PF: error_code(0x0002) - not-present page
[ 4570.697401] PGD 0 P4D 0
[ 4570.697716] Oops: 0002 [#1] PREEMPT SMP NOPTI
[ 4570.698228] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.16.0-rc4+ #111
[ 4570.699013] Hardware name: Alibaba Cloud Alibaba Cloud ECS, BIOS 8c24b4c 04/0
[ 4570.699933] RIP: 0010:_raw_spin_lock+0x1a/0x30
<...>
[ 4570.711446] Call Trace:
[ 4570.711746] <IRQ>
[ 4570.711992] smc_cdc_tx_handler+0x41/0xc0
[ 4570.712470] smc_wr_tx_tasklet_fn+0x213/0x560
[ 4570.712981] ? smc_cdc_tx_dismisser+0x10/0x10
[ 4570.713489] tasklet_action_common.isra.17+0x66/0x140
[ 4570.714083] __do_softirq+0x123/0x2f4
[ 4570.714521] irq_exit_rcu+0xc4/0xf0
[ 4570.714934] common_interrupt+0xba/0xe0
Though smc_cdc_tx_handler() checked the existence of smc connection,
smc_release() may have already dismissed and released the smc socket
before smc_cdc_tx_handler() further visits it.
smc_cdc_tx_handler() |smc_release()
if (!conn) |
|
|smc_cdc_tx_dismiss_slots()
| smc_cdc_tx_dismisser()
|
|sock_put(&smc->sk) <- last sock_put,
| smc_sock freed
bh_lock_sock(&smc->sk) (panic) |
To make sure we won't receive any CDC messages after we free the
smc_sock, add a refcount on the smc_connection for inflight CDC
message(posted to the QP but haven't received related CQE), and
don't release the smc_connection until all the inflight CDC messages
haven been done, for both success or failed ones.
Using refcount on CDC messages brings another problem: when the link
is going to be destroyed, smcr_link_clear() will reset the QP, which
then remove all the pending CQEs related to the QP in the CQ. To make
sure all the CQEs will always come back so the refcount on the
smc_connection can always reach 0, smc_ib_modify_qp_reset() was replaced
by smc_ib_modify_qp_error().
And remove the timeout in smc_wr_tx_wait_no_pending_sends() since we
need to wait for all pending WQEs done, or we may encounter use-after-
free when handling CQEs.
For IB device removal routine, we need to wait for all the QPs on that
device been destroyed before we can destroy CQs on the device, or
the refcount on smc_connection won't reach 0 and smc_sock cannot be
released.
Fixes: 5f08318f61 ("smc: connection data control (CDC)")
Reported-by: Wen Gu <guwen@linux.alibaba.com>
Signed-off-by: Dust Li <dust.li@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90cee52f2e ]
We found smc_llc_send_link_delete_all() sometimes wait
for 2s timeout when testing with RDMA link up/down.
It is possible when a smc_link is in ACTIVATING state,
the underlaying QP is still in RESET or RTR state, which
cannot send any messages out.
smc_llc_send_link_delete_all() use smc_link_usable() to
checks whether the link is usable, if the QP is still in
RESET or RTR state, but the smc_link is in ACTIVATING, this
LLC message will always fail without any CQE entering the
CQ, and we will always wait 2s before timeout.
Since we cannot send any messages through the QP before
the QP enter RTS. I add a wrapper smc_link_sendable()
which checks the state of QP along with the link state.
And replace smc_link_usable() with smc_link_sendable()
in all LLC & CDC message sending routine.
Fixes: 5f08318f61 ("smc: connection data control (CDC)")
Signed-off-by: Dust Li <dust.li@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95f7f3e7dc ]
Commit 8f3d65c166 ("net/smc: fix wait on already cleared link")
introduced link refcounting to avoid waits on already cleared links.
This patch extents and improves the refcounting to cover all
remaining possible cases for this kind of error situation.
Fixes: 15e1b99aad ("net/smc: no WR buffer wait for terminating link group")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5be60a9453 ]
Received frames have FCS truncated. There is no need
to subtract FCS length from the statistics.
Fixes: fe1a56420c ("net: lantiq: Add Lantiq / Intel VRX200 Ethernet driver")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1cd5384c88 ]
'ndev' is a managed resource allocated with devm_alloc_etherdev(), so there
is no need to call free_netdev() explicitly or there will be a double
free().
Simplify all error handling paths accordingly.
Fixes: d51b6ce441 ("net: ethernet: add ag71xx driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca506fca46 ]
The D-Link DSB-650TX (2001:4002) is unable to receive Ethernet frames
that are longer than 1518 octets, for example, Ethernet frames that
contain 802.1Q VLAN tags.
The frames are sent to the pegasus driver via USB but the driver
discards them because they have the Long_pkt field set to 1 in the
received status report. The function read_bulk_callback of the pegasus
driver treats such received "packets" (in the terminology of the
hardware) as errors but the field simply does just indicate that the
Ethernet frame (MAC destination to FCS) is longer than 1518 octets.
It seems that in the 1990s there was a distinction between
"giant" (> 1518) and "runt" (< 64) frames and the hardware includes
flags to indicate this distinction. It seems that the purpose of the
distinction "giant" frames was to not allow infinitely long frames due
to transmission errors and to allow hardware to have an upper limit of
the frame size. However, the hardware already has such limit with its
2048 octet receive buffer and, therefore, Long_pkt is merely a
convention and should not be treated as a receive error.
Actually, the hardware is even able to receive Ethernet frames with 2048
octets which exceeds the claimed limit frame size limit of the driver of
1536 octets (PEGASUS_MTU).
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Matthias-Christian Ott <ott@mirix.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d7373dabf ]
In smc_wr_tx_send_wait() the completion on index specified by
pend->idx is initialized and after smc_wr_tx_send() was called the wait
for completion starts. pend->idx is used to get the correct index for
the wait, but the pend structure could already be cleared in
smc_wr_tx_process_cqe().
Introduce pnd_idx to hold and use a local copy of the correct index.
Fixes: 09c61d24f9 ("net/smc: wait for departure of an IB message")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ec7d18d18 ]
This patch is to delay the endpoint free by calling call_rcu() to fix
another use-after-free issue in sctp_sock_dump():
BUG: KASAN: use-after-free in __lock_acquire+0x36d9/0x4c20
Call Trace:
__lock_acquire+0x36d9/0x4c20 kernel/locking/lockdep.c:3218
lock_acquire+0x1ed/0x520 kernel/locking/lockdep.c:3844
__raw_spin_lock_bh include/linux/spinlock_api_smp.h:135 [inline]
_raw_spin_lock_bh+0x31/0x40 kernel/locking/spinlock.c:168
spin_lock_bh include/linux/spinlock.h:334 [inline]
__lock_sock+0x203/0x350 net/core/sock.c:2253
lock_sock_nested+0xfe/0x120 net/core/sock.c:2774
lock_sock include/net/sock.h:1492 [inline]
sctp_sock_dump+0x122/0xb20 net/sctp/diag.c:324
sctp_for_each_transport+0x2b5/0x370 net/sctp/socket.c:5091
sctp_diag_dump+0x3ac/0x660 net/sctp/diag.c:527
__inet_diag_dump+0xa8/0x140 net/ipv4/inet_diag.c:1049
inet_diag_dump+0x9b/0x110 net/ipv4/inet_diag.c:1065
netlink_dump+0x606/0x1080 net/netlink/af_netlink.c:2244
__netlink_dump_start+0x59a/0x7c0 net/netlink/af_netlink.c:2352
netlink_dump_start include/linux/netlink.h:216 [inline]
inet_diag_handler_cmd+0x2ce/0x3f0 net/ipv4/inet_diag.c:1170
__sock_diag_cmd net/core/sock_diag.c:232 [inline]
sock_diag_rcv_msg+0x31d/0x410 net/core/sock_diag.c:263
netlink_rcv_skb+0x172/0x440 net/netlink/af_netlink.c:2477
sock_diag_rcv+0x2a/0x40 net/core/sock_diag.c:274
This issue occurs when asoc is peeled off and the old sk is freed after
getting it by asoc->base.sk and before calling lock_sock(sk).
To prevent the sk free, as a holder of the sk, ep should be alive when
calling lock_sock(). This patch uses call_rcu() and moves sock_put and
ep free into sctp_endpoint_destroy_rcu(), so that it's safe to try to
hold the ep under rcu_read_lock in sctp_transport_traverse_process().
If sctp_endpoint_hold() returns true, it means this ep is still alive
and we have held it and can continue to dump it; If it returns false,
it means this ep is dead and can be freed after rcu_read_unlock, and
we should skip it.
In sctp_sock_dump(), after locking the sk, if this ep is different from
tsp->asoc->ep, it means during this dumping, this asoc was peeled off
before calling lock_sock(), and the sk should be skipped; If this ep is
the same with tsp->asoc->ep, it means no peeloff happens on this asoc,
and due to lock_sock, no peeloff will happen either until release_sock.
Note that delaying endpoint free won't delay the port release, as the
port release happens in sctp_endpoint_destroy() before calling call_rcu().
Also, freeing endpoint by call_rcu() makes it safe to access the sk by
asoc->base.sk in sctp_assocs_seq_show() and sctp_rcv().
Thanks Jones to bring this issue up.
v1->v2:
- improve the changelog.
- add kfree(ep) into sctp_endpoint_destroy_rcu(), as Jakub noticed.
Reported-by: syzbot+9276d76e83e3bcde6c99@syzkaller.appspotmail.com
Reported-by: Lee Jones <lee.jones@linaro.org>
Fixes: d25adbeb0c ("sctp: fix an use-after-free issue in sctp_sock_dump")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5471d5226c ]
The below referenced commit correctly updated the computation of number
of segments (gso_size) by using only the gso payload size and
removing the header lengths.
With this change the regression test started failing. Update
the tests to match this new behavior.
Both IPv4 and IPv6 tests are updated, as a separate patch in this series
will update udp_v6_send_skb to match this change in udp_send_skb.
Fixes: 158390e456 ("udp: using datalen to cap max gso segments")
Signed-off-by: Coco Li <lixiaoyan@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20211223222441.2975883-2-lixiaoyan@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 736ef37fd9 ]
The max number of UDP gso segments is intended to cap to
UDP_MAX_SEGMENTS, this is checked in udp_send_skb().
skb->len contains network and transport header len here, we should use
only data len instead.
This is the ipv6 counterpart to the below referenced commit,
which missed the ipv6 change
Fixes: 158390e456 ("udp: using datalen to cap max gso segments")
Signed-off-by: Coco Li <lixiaoyan@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20211223222441.2975883-1-lixiaoyan@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19c4aba2d4 ]
There are two ICOSQs per channel: one is needed for RX, and the other
for async operations (XSK TX, kTLS offload). Currently, the recovery
flow for both is the same, and async ICOSQ is mistakenly treated like
the regular ICOSQ.
This patch prevents running the regular ICOSQ recovery on async ICOSQ.
The purpose of async ICOSQ is to handle XSK wakeup requests and post
kTLS offload RX parameters, it has nothing to do with RQ and XSKRQ UMRs,
so the regular recovery sequence is not applicable here.
Fixes: be5323c837 ("net/mlx5e: Report and recover from CQE error on ICOSQ")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 732bc2ff08 upstream.
Clang static analysis reports this warning
hooks.c:5765:6: warning: 4th function call argument is an uninitialized
value
if (selinux_xfrm_postroute_last(sksec->sid, skb, &ad, proto))
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
selinux_parse_skb() can return ok without setting proto. The later call
to selinux_xfrm_postroute_last() does an early check of proto and can
return ok if the garbage proto value matches. So initialize proto.
Cc: stable@vger.kernel.org
Fixes: eef9b41622 ("selinux: cleanup selinux_xfrm_sock_rcv_skb() and selinux_xfrm_postroute_last()")
Signed-off-by: Tom Rix <trix@redhat.com>
[PM: typo/spelling and checkpatch.pl description fixes]
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4eb1782eaa upstream.
Commit 85bf17b28f ("recordmcount.pl: look for jgnop instruction as well
as bcrl on s390") added a new alternative mnemonic for the existing brcl
instruction. This is required for the combination old gcc version (pre 9.0)
and binutils since version 2.37.
However at the same time this commit introduced a typo, replacing brcl with
bcrl. As a result no mcount locations are detected anymore with old gcc
versions (pre 9.0) and binutils before version 2.37.
Fix this by using the correct mnemonic again.
Reported-by: Miroslav Benes <mbenes@suse.cz>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: <stable@vger.kernel.org>
Fixes: 85bf17b28f ("recordmcount.pl: look for jgnop instruction as well as bcrl on s390")
Link: https://lore.kernel.org/r/alpine.LSU.2.21.2112230949520.19849@pobox.suse.cz
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d7f55471db ]
Fix modpost Section mismatch error in memblock_phys_alloc()
[...]
WARNING: modpost: vmlinux.o(.text.unlikely+0x1dcc): Section mismatch in reference
from the function memblock_phys_alloc() to the function .init.text:memblock_phys_alloc_range()
The function memblock_phys_alloc() references
the function __init memblock_phys_alloc_range().
This is often because memblock_phys_alloc lacks a __init
annotation or the annotation of memblock_phys_alloc_range is wrong.
ERROR: modpost: Section mismatches detected.
Set CONFIG_SECTION_MISMATCH_WARN_ONLY=y to allow them.
[...]
memblock_phys_alloc() is a one-line wrapper, make it __always_inline to
avoid these section mismatches.
Reported-by: k2ci <kernel-bot@kylinos.cn>
Suggested-by: Mike Rapoport <rppt@kernel.org>
Signed-off-by: Jackie Liu <liuyun01@kylinos.cn>
[rppt: slightly massaged changelog ]
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Link: https://lore.kernel.org/r/20211217020754.2874872-1-liu.yun@linux.dev
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 484730e586 ]
When a trap 7 (Instruction access rights) occurs, this means the CPU
couldn't execute an instruction due to missing execute permissions on
the memory region. In this case it seems the CPU didn't even fetched
the instruction from memory and thus did not store it in the cr19 (IIR)
register before calling the trap handler. So, the trap handler will find
some random old stale value in cr19.
This patch simply overwrites the stale IIR value with a constant magic
"bad food" value (0xbaadf00d), in the hope people don't start to try to
understand the various random IIR values in trap 7 dumps.
Noticed-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f702e11076 ]
hwight16() is much faster. While we are at it, no need to include
"perm =" part into data_race() macro, for perm is a local variable
that cannot be accessed by other threads.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04e57a2d95 ]
If tomoyo is used in a testing/fuzzing environment in learning mode,
for lots of domains the quota will be exceeded and stay exceeded
for prolonged periods of time. In such cases it's pointless (and slow)
to walk the whole acl list again and again just to rediscover that
the quota is exceeded. We already have the TOMOYO_DIF_QUOTA_WARNED flag
that notes the overflow condition. Check it early to avoid the slowdown.
[penguin-kernel]
This patch causes a user visible change that the learning mode will not be
automatically resumed after the quota is increased. To resume the learning
mode, administrator will need to explicitly clear TOMOYO_DIF_QUOTA_WARNED
flag after increasing the quota. But I think that this change is generally
preferable, for administrator likely wants to optimize the acl list for
that domain before increasing the quota, or that domain likely hits the
quota again. Therefore, don't try to care to clear TOMOYO_DIF_QUOTA_WARNED
flag automatically when the quota for that domain changed.
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9222ba68c3 ]
We've got a bug report about the non-working keyboard on ASUS ZenBook
UX425UA. It seems that the PS/2 device isn't ready immediately at
boot but takes some seconds to get ready. Until now, the only
workaround is to defer the probe, but it's available only when the
driver is a module. However, many distros, including openSUSE as in
the original report, build the PS/2 input drivers into kernel, hence
it won't work easily.
This patch adds the support for the deferred probe for i8042 stuff as
a workaround of the problem above. When the deferred probe mode is
enabled and the device couldn't be probed, it'll be repeated with the
standard deferred probe mechanism.
The deferred probe mode is enabled either via the new option
i8042.probe_defer or via the quirk table entry. As of this patch, the
quirk table contains only ASUS ZenBook UX425UA.
The deferred probe part is based on Fabio's initial work.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1190256
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Samuel Čavoj <samuel@cavoj.net>
Link: https://lore.kernel.org/r/20211117063757.11380-1-tiwai@suse.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
The drm edid parser doesn't signal RGB support on DVI monitors
with old edid versions, leading to 8-bit RGB mode being rejected
and no video on DVI monitors.
As 8-bit RGB is mandatory on HDMI and DVI monitors anyways we can
simply drop the RGB format check, aligning vc4 with other drivers.
Signed-off-by: Matthias Reichl <hias@horus.com>
When vc4_hdmi_connector_detect() was called in
connector_status_connected state it incorrectly cleared the
hdmi_monitor flag, leading to no audio on RPi3.
Fix this by clearing hdmi_monitor only when the hpd check
indicated no connection or if reading the edid failed.
Signed-off-by: Matthias Reichl <hias@horus.com>
commit 75a2f31520 upstream.
This ioctl() implicitly assumed that the socket was already bound to
a valid local socket name, i.e. Phonet object. If the socket was not
bound, two separate problems would occur:
1) We'd send an pipe enablement request with an invalid source object.
2) Later socket calls could BUG on the socket unexpectedly being
connected yet not bound to a valid object.
Reported-by: syzbot+2dc91e7fc3dea88b1e8a@syzkaller.appspotmail.com
Signed-off-by: Rémi Denis-Courmont <remi@remlab.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2f37aead1 upstream.
The previous commit 3e0588c291 ("hamradio: defer ax25 kfree after
unregister_netdev") reorder the kfree operations and unregister_netdev
operation to prevent UAF.
This commit improves the previous one by also deferring the nullify of
the ax->tty pointer. Otherwise, a NULL pointer dereference bug occurs.
Partial of the stack trace is shown below.
BUG: kernel NULL pointer dereference, address: 0000000000000538
RIP: 0010:ax_xmit+0x1f9/0x400
...
Call Trace:
dev_hard_start_xmit+0xec/0x320
sch_direct_xmit+0xea/0x240
__qdisc_run+0x166/0x5c0
__dev_queue_xmit+0x2c7/0xaf0
ax25_std_establish_data_link+0x59/0x60
ax25_connect+0x3a0/0x500
? security_socket_connect+0x2b/0x40
__sys_connect+0x96/0xc0
? __hrtimer_init+0xc0/0xc0
? common_nsleep+0x2e/0x50
? switch_fpu_return+0x139/0x1a0
__x64_sys_connect+0x11/0x20
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xa9
The crash point is shown as below
static void ax_encaps(...) {
...
set_bit(TTY_DO_WRITE_WAKEUP, &ax->tty->flags); // ax->tty = NULL!
...
}
By placing the nullify action after the unregister_netdev, the ax->tty
pointer won't be assigned as NULL net_device framework layer is well
synchronized.
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e0588c291 upstream.
There is a possible race condition (use-after-free) like below
(USE) | (FREE)
ax25_sendmsg |
ax25_queue_xmit |
dev_queue_xmit |
__dev_queue_xmit |
__dev_xmit_skb |
sch_direct_xmit | ...
xmit_one |
netdev_start_xmit | tty_ldisc_kill
__netdev_start_xmit | mkiss_close
ax_xmit | kfree
ax_encaps |
|
Even though there are two synchronization primitives before the kfree:
1. wait_for_completion(&ax->dead). This can prevent the race with
routines from mkiss_ioctl. However, it cannot stop the routine coming
from upper layer, i.e., the ax25_sendmsg.
2. netif_stop_queue(ax->dev). It seems that this line of code aims to
halt the transmit queue but it fails to stop the routine that already
being xmit.
This patch reorder the kfree after the unregister_netdev to avoid the
possible UAF as the unregister_netdev() is well synchronized and won't
return if there is a running routine.
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ade48d0c2 upstream.
The existing cleanup routine implementation is not well synchronized
with the syscall routine. When a device is detaching, below race could
occur.
static int ax25_sendmsg(...) {
...
lock_sock()
ax25 = sk_to_ax25(sk);
if (ax25->ax25_dev == NULL) // CHECK
...
ax25_queue_xmit(skb, ax25->ax25_dev->dev); // USE
...
}
static void ax25_kill_by_device(...) {
...
if (s->ax25_dev == ax25_dev) {
s->ax25_dev = NULL;
...
}
Other syscall functions like ax25_getsockopt, ax25_getname,
ax25_info_show also suffer from similar races. To fix them, this patch
introduce lock_sock() into ax25_kill_by_device in order to guarantee
that the nullify action in cleanup routine cannot proceed when another
socket request is pending.
Signed-off-by: Hanjie Wu <nagi@zju.edu.cn>
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cdc5287aca upstream.
Bit 7 of the status register indicates that the chip is busy
doing a conversion. It does not indicate an alarm status.
Stop reporting it as alarm status bit.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da7dc05684 upstream.
Tests with a real chip and a closer look into the datasheet reveals
that the local and remote critical alarm status bits are swapped for
MAX6680/MAX6681.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ff29701ff upstream.
Update the documentation for kvm-intel's emulate_invalid_guest_state to
rectify the description of KVM's default behavior, and to document that
the behavior and thus parameter only applies to L1.
Fixes: a27685c33a ("KVM: VMX: Emulate invalid guest state by default")
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211207193006.120997-4-seanjc@google.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 890d5b4090 upstream.
When listening for notifications through netlink of a new interface being
registered, sporadically, it is possible for the MAC to be read as zero.
The zero MAC address lasts a short period of time and then switches to a
valid random MAC address.
This causes problems for netd in Android, which assumes that the interface
is malfunctioning and will not use it.
In the good case we get this log:
InterfaceController::getCfg() ifName usb0
hwAddr 92:a8:f0:73:79:5b ipv4Addr 0.0.0.0 flags 0x1002
In the error case we get these logs:
InterfaceController::getCfg() ifName usb0
hwAddr 00:00:00:00:00:00 ipv4Addr 0.0.0.0 flags 0x1002
netd : interfaceGetCfg("usb0")
netd : interfaceSetCfg() -> ServiceSpecificException
(99, "[Cannot assign requested address] : ioctl() failed")
The reason for the issue is the order in which the interface is setup,
it is first registered through register_netdev() and after the MAC
address is set.
Fixed by first setting the MAC address of the net_device and after that
calling register_netdev().
Fixes: bcd4a1c40b ("usb: gadget: u_ether: construct with default values and add setters/getters")
Cc: stable@vger.kernel.org
Signed-off-by: Marian Postevca <posteuca@mutex.one>
Link: https://lore.kernel.org/r/20211204214912.17627-1-posteuca@mutex.one
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd84bfdddd upstream.
Ceph always inherits the SGID bit if it is set on the parent inode,
while the generic inode_init_owner does not do this in a few cases where
it can create a possible security problem (cf. [1]).
Update ceph to strip the SGID bit just as inode_init_owner would.
This bug was detected by the mapped mount testsuite in [3]. The
testsuite tests all core VFS functionality and semantics with and
without mapped mounts. That is to say it functions as a generic VFS
testsuite in addition to a mapped mount testsuite. While working on
mapped mount support for ceph, SIGD inheritance was the only failing
test for ceph after the port.
The same bug was detected by the mapped mount testsuite in XFS in
January 2021 (cf. [2]).
[1]: commit 0fa3ecd878 ("Fix up non-directory creation in SGID directories")
[2]: commit 01ea173e10 ("xfs: fix up non-directory creation in SGID directories")
[3]: https://git.kernel.org/fs/xfs/xfstests-dev.git
Cc: stable@vger.kernel.org
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5598b24efaf4892741c798b425d543e4bed357a1 upstream.
As Wenqing Liu reported in bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=215235
- Overview
page fault in f2fs_setxattr() when mount and operate on corrupted image
- Reproduce
tested on kernel 5.16-rc3, 5.15.X under root
1. unzip tmp7.zip
2. ./single.sh f2fs 7
Sometimes need to run the script several times
- Kernel dump
loop0: detected capacity change from 0 to 131072
F2FS-fs (loop0): Found nat_bits in checkpoint
F2FS-fs (loop0): Mounted with checkpoint version = 7548c2ee
BUG: unable to handle page fault for address: ffffe47bc7123f48
RIP: 0010:kfree+0x66/0x320
Call Trace:
__f2fs_setxattr+0x2aa/0xc00 [f2fs]
f2fs_setxattr+0xfa/0x480 [f2fs]
__f2fs_set_acl+0x19b/0x330 [f2fs]
__vfs_removexattr+0x52/0x70
__vfs_removexattr_locked+0xb1/0x140
vfs_removexattr+0x56/0x100
removexattr+0x57/0x80
path_removexattr+0xa3/0xc0
__x64_sys_removexattr+0x17/0x20
do_syscall_64+0x37/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
The root cause is in __f2fs_setxattr(), we missed to do sanity check on
last xattr entry, result in out-of-bound memory access during updating
inconsistent xattr data of target inode.
After the fix, it can detect such xattr inconsistency as below:
F2FS-fs (loop11): inode (7) has invalid last xattr entry, entry_size: 60676
F2FS-fs (loop11): inode (8) has corrupted xattr
F2FS-fs (loop11): inode (8) has corrupted xattr
F2FS-fs (loop11): inode (8) has invalid last xattr entry, entry_size: 47736
Cc: stable@vger.kernel.org
Reported-by: Wenqing Liu <wenqingliu0120@gmail.com>
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 18549bf4b2 upstream.
Pointer to the allocated pages (struct page *page) has already
progressed towards the end of allocation. It is incorrect to perform
__free_pages(page, order) using this pointer as we would free any
arbitrary pages. Fix this by stop modifying the page pointer.
Fixes: ec185dd3ab ("optee: Fix memory leak when failing to register shm pages")
Cc: stable@vger.kernel.org
Reported-by: Patrik Lantz <patrik.lantz@axis.com>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a57d83c78 upstream.
Hulk Robot reported a panic in put_page_testzero() when testing
madvise() with MADV_SOFT_OFFLINE. The BUG() is triggered when retrying
get_any_page(). This is because we keep MF_COUNT_INCREASED flag in
second try but the refcnt is not increased.
page dumped because: VM_BUG_ON_PAGE(page_ref_count(page) == 0)
------------[ cut here ]------------
kernel BUG at include/linux/mm.h:737!
invalid opcode: 0000 [#1] PREEMPT SMP
CPU: 5 PID: 2135 Comm: sshd Tainted: G B 5.16.0-rc6-dirty #373
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014
RIP: release_pages+0x53f/0x840
Call Trace:
free_pages_and_swap_cache+0x64/0x80
tlb_flush_mmu+0x6f/0x220
unmap_page_range+0xe6c/0x12c0
unmap_single_vma+0x90/0x170
unmap_vmas+0xc4/0x180
exit_mmap+0xde/0x3a0
mmput+0xa3/0x250
do_exit+0x564/0x1470
do_group_exit+0x3b/0x100
__do_sys_exit_group+0x13/0x20
__x64_sys_exit_group+0x16/0x20
do_syscall_64+0x34/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
Modules linked in:
---[ end trace e99579b570fe0649 ]---
RIP: 0010:release_pages+0x53f/0x840
Link: https://lkml.kernel.org/r/20211221074908.3910286-1-liushixin2@huawei.com
Fixes: b94e02822d ("mm,hwpoison: try to narrow window race for free pages")
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Acked-by: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8536a5ef88 upstream.
The Thumb2 version of the FP exception handling entry code treats the
register holding the CP number (R8) differently, resulting in the iWMMXT
CP number check to be incorrect.
Fix this by unifying the ARM and Thumb2 code paths, and switch the
order of the additions of the TI_USED_CP offset and the shifted CP
index.
Cc: <stable@vger.kernel.org>
Fixes: b86040a59f ("Thumb-2: Implementation of the unified start-up and exceptions code")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f89b548ca6 upstream.
The vendor driver implements special handling for multi-block
SD_IO_RW_EXTENDED (and SD_IO_RW_DIRECT) commands which have data
attached to them. It sets the MANUAL_STOP bit in the MESON_SDHC_MISC
register for these commands. In all other cases this bit is cleared.
Here we omit SD_IO_RW_DIRECT since that command never has any data
attached to it.
This fixes SDIO wifi using the brcmfmac driver which reported the
following error without this change on a Netxeon S82 board using a
Meson8 (S802) SoC:
brcmf_fw_alloc_request: using brcm/brcmfmac43362-sdio for chip
BCM43362/1
brcmf_sdiod_ramrw: membytes transfer failed
brcmf_sdio_download_code_file: error -110 on writing 219557 membytes
at 0x00000000
brcmf_sdio_download_firmware: dongle image file download failed
And with this change:
brcmf_fw_alloc_request: using brcm/brcmfmac43362-sdio for chip
BCM43362/1
brcmf_c_process_clm_blob: no clm_blob available (err=-2), device may
have limited channels available
brcmf_c_preinit_dcmds: Firmware: BCM43362/1 wl0: Apr 22 2013 14:50:00
version 5.90.195.89.6 FWID 01-b30a427d
Fixes: e4bf1b0970 ("mmc: host: meson-mx-sdhc: new driver for the Amlogic Meson SDHC host")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211219153442.463863-2-martin.blumenstingl@googlemail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a5875f14b upstream.
When replugging the device the following message shows up:
gpio gpiochip2: (dln2): detected irqchip that is shared with multiple gpiochips: please fix the driver.
This also has the effect that interrupts won't work.
The same problem would also show up if multiple devices where plugged in.
Fix this by allocating the irq_chip data structure per instance like other
drivers do.
I don't know when this problem appeared, but it is present in 5.10.
Cc: <stable@vger.kernel.org> # 5.10+
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fdba608f15 upstream.
Drop a check that guards triggering a posted interrupt on the currently
running vCPU, and more importantly guards waking the target vCPU if
triggering a posted interrupt fails because the vCPU isn't IN_GUEST_MODE.
If a vIRQ is delivered from asynchronous context, the target vCPU can be
the currently running vCPU and can also be blocking, in which case
skipping kvm_vcpu_wake_up() is effectively dropping what is supposed to
be a wake event for the vCPU.
The "do nothing" logic when "vcpu == running_vcpu" mostly works only
because the majority of calls to ->deliver_posted_interrupt(), especially
when using posted interrupts, come from synchronous KVM context. But if
a device is exposed to the guest using vfio-pci passthrough, the VFIO IRQ
and vCPU are bound to the same pCPU, and the IRQ is _not_ configured to
use posted interrupts, wake events from the device will be delivered to
KVM from IRQ context, e.g.
vfio_msihandler()
|
|-> eventfd_signal()
|
|-> ...
|
|-> irqfd_wakeup()
|
|->kvm_arch_set_irq_inatomic()
|
|-> kvm_irq_delivery_to_apic_fast()
|
|-> kvm_apic_set_irq()
This also aligns the non-nested and nested usage of triggering posted
interrupts, and will allow for additional cleanups.
Fixes: 379a3c8ee4 ("KVM: VMX: Optimize posted-interrupt delivery for timer fastpath")
Cc: stable@vger.kernel.org
Reported-by: Longpeng (Mike) <longpeng2@huawei.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20211208015236.1616697-18-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 57690554ab upstream.
Both __pkru_allows_write() and arch_set_user_pkey_access() shift
PKRU_WD_BIT (a signed constant) by up to 30 bits, hitting the
sign bit.
Use unsigned constants instead.
Clearly pkey 15 has not been used in combination with UBSAN yet.
Noticed by code inspection only. I can't actually provoke the
compiler into generating incorrect logic as far as this shift is
concerned.
[
dhansen: add stable@ tag, plus minor changelog massaging,
For anyone doing backports, these #defines were in
arch/x86/include/asm/pgtable.h before 784a46618f.
]
Fixes: 33a709b25a ("mm/gup, x86/mm/pkeys: Check VMAs and PTEs for protection keys")
Signed-off-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20211216000856.4480-1-andrew.cooper3@citrix.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dfd0743f1d upstream.
Since the tee subsystem does not keep a strong reference to its idle
shared memory buffers, it races with other threads that try to destroy a
shared memory through a close of its dma-buf fd or by unmapping the
memory.
In tee_shm_get_from_id() when a lookup in teedev->idr has been
successful, it is possible that the tee_shm is in the dma-buf teardown
path, but that path is blocked by the teedev mutex. Since we don't have
an API to tell if the tee_shm is in the dma-buf teardown path or not we
must find another way of detecting this condition.
Fix this by doing the reference counting directly on the tee_shm using a
new refcount_t refcount field. dma-buf is replaced by using
anon_inode_getfd() instead, this separates the life-cycle of the
underlying file from the tee_shm. tee_shm_put() is updated to hold the
mutex when decreasing the refcount to 0 and then remove the tee_shm from
teedev->idr before releasing the mutex. This means that the tee_shm can
never be found unless it has a refcount larger than 0.
Fixes: 967c9cca2c ("tee: generic TEE subsystem")
Cc: stable@vger.kernel.org
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Lars Persson <larper@axis.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Reported-by: Patrik Lantz <patrik.lantz@axis.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3a5a68cff upstream.
The address bits used to select the futex spinlock need to match those used in
the LWS code in syscall.S. The mask 0x3f8 only selects 7 bits. It should
select 8 bits.
This change fixes the glibc nptl/tst-cond24 and nptl/tst-cond25 tests.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Fixes: 53a42b6324 ("parisc: Switch to more fine grained lws locks")
Cc: stable@vger.kernel.org # 5.10+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f66fce0f4 upstream.
The completer in the "or,ev %r1,%r30,%r30" instruction is reversed, so we are
not clipping the LWS number when we are called from a 32-bit process (W=0).
We need to nulify the following depdi instruction when the least-significant
bit of %r30 is 1.
If the %r20 register is not clipped, a user process could perform a LWS call
that would branch to an undefined location in the kernel and potentially crash
the machine.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # 4.19+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 34f35f8f14 upstream.
During probe ssif_info->client is dereferenced in error path. However,
it is set when some of the error checking has already been done. This
causes following kernel crash if an error path is taken:
[ 30.645593][ T674] ipmi_ssif 0-000e: ipmi_ssif: Not probing, Interface already present
[ 30.657616][ T674] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000088
...
[ 30.657723][ T674] pc : __dev_printk+0x28/0xa0
[ 30.657732][ T674] lr : _dev_err+0x7c/0xa0
...
[ 30.657772][ T674] Call trace:
[ 30.657775][ T674] __dev_printk+0x28/0xa0
[ 30.657778][ T674] _dev_err+0x7c/0xa0
[ 30.657781][ T674] ssif_probe+0x548/0x900 [ipmi_ssif 62ce4b08badc1458fd896206d9ef69a3c31f3d3e]
[ 30.657791][ T674] i2c_device_probe+0x37c/0x3c0
...
Initialize ssif_info->client before any error path can be taken. Clear
i2c_client data in the error path to prevent the dangling pointer from
leaking.
Fixes: c4436c9149 ("ipmi_ssif: avoid registering duplicate ssif interface")
Cc: stable@vger.kernel.org # 5.4.x
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Message-Id: <20211208093239.4432-1-ykaukab@suse.de>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee907afb0c upstream.
The out-of-tree vendor driver uses the following approach to set the
AIU_I2S_MISC register:
1) write AIU_MEM_I2S_START_PTR and AIU_MEM_I2S_RD_PTR
2) configure AIU_I2S_MUTE_SWAP[15:0]
3) write AIU_MEM_I2S_END_PTR
4) set AIU_I2S_MISC[2] to 1 (documented as: "put I2S interface in hold
mode")
5) set AIU_I2S_MISC[4] to 1 (depending on the driver revision it always
stays at 1 while for older drivers this bit is unset in step 4)
6) set AIU_I2S_MISC[2] to 0
7) write AIU_MEM_I2S_MASKS
8) toggle AIU_MEM_I2S_CONTROL[0]
9) toggle AIU_MEM_I2S_BUF_CNTL[0]
Move setting the AIU_I2S_MISC[2] bit to aiu_fifo_i2s_hw_params() so it
resembles the flow in the vendor kernel more closely. While here also
configure AIU_I2S_MISC[4] (documented as: "force each audio data to
left or right according to the bit attached with the audio data")
similar to how the vendor driver does this. This fixes the infamous and
long-standing "machine gun noise" issue (a buffer underrun issue).
Fixes: 6ae9ca9ce9 ("ASoC: meson: aiu: add i2s and spdif support")
Reported-by: Christian Hewitt <christianshewitt@gmail.com>
Reported-by: Geraldo Nascimento <geraldogabriel@gmail.com>
Tested-by: Christian Hewitt <christianshewitt@gmail.com>
Tested-by: Geraldo Nascimento <geraldogabriel@gmail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Cc: stable@vger.kernel.org
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20211206210804.2512999-3-martin.blumenstingl@googlemail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit edca7cc4b0 upstream.
The Clevo NJ51CU comes either with the ALC293 or the ALC256 codec, but uses
the 0x8686 subproduct id in both cases. The ALC256 codec needs a different
quirk for the headset microphone working and and edditional quirk for sound
working after suspend and resume.
When waking up from s3 suspend the Coef 0x10 is set to 0x0220 instead of
0x0020 on the ALC256 codec. Setting the value manually makes the sound
work again. This patch does this automatically.
[ minor coding style fix by tiwai ]
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Fixes: b5acfe152a ("ALSA: hda/realtek: Add some Clove SSID in the ALC293(ALC1220)")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211215191646.844644-1-wse@tuxedocomputers.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2dee54b289 upstream.
Static analysis with scan-build has found an assignment to vp2 that is
never used. It seems that the check on vp->state > 0 should be actually
on vp2->state instead. Fix this.
This dates back to 2002, I found the offending commit from the git
history git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git,
commit 91e39521bbf6 ("[PATCH] ALSA patch for 2.5.4")
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211212172025.470367-1-colin.i.king@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 16ba51b5dc ]
Tests with a real chip and a closer look into the datasheet show that
MAX6654 does not support CRIT/THERM/OVERTEMP limits, so drop support
of the respective attributes for this chip.
Introduce LM90_HAVE_CRIT flag and use it to instantiate critical limit
attributes to solve the problem.
Cc: Josh Lehan <krellan@google.com>
Fixes: 229d495d81 ("hwmon: (lm90) Add max6654 support to lm90 driver")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f347e249fc ]
A flag indicating extended temperature support makes it easier
to add support for additional chips with this functionality.
Cc: David T. Wilson <david.wilson@nasa.gov>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8344f7693 ]
TMP461 is almost identical to TMP451 and was actually detected as TMP451
with the existing lm90 driver if its I2C address is 0x4c. Add support
for it to the lm90 driver. At the same time, improve the chip detection
function to at least try to distinguish between TMP451 and TMP461.
As a side effect, this fixes commit 24333ac26d ("hwmon: (tmp401) use
smb word operations instead of 2 smb byte operations"). TMP461 does not
support word operations on temperature registers, which causes bad
temperature readings with the tmp401 driver. The lm90 driver does not
perform word operations on temperature registers and thus does not have
this problem.
Support is listed as basic because TMP461 supports a sensor resolution
of 0.0625 degrees C, while the lm90 driver assumes a resolution of 0.125
degrees C. Also, the TMP461 supports negative temperatures with its
default temperature range, which is not the case for similar chips
supported by the lm90 and the tmp401 drivers. Those limitations will be
addressed with follow-up patches.
Fixes: 24333ac26d ("hwmon: (tmp401) use smb word operations instead of 2 smb byte operations")
Reported-by: David T. Wilson <david.wilson@nasa.gov>
Cc: David T. Wilson <david.wilson@nasa.gov>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fce15c45d3 ]
The detect function had a comment "Make compiler happy" when id did not
read the second configuration register. As it turns out, the code was
checking the contents of this register for manufacturer ID 0xA1 (NXP
Semiconductor/Philips), but never actually read the register. So it
wasn't surprising that the compiler complained, and it indeed had a point.
Fix the code to read the register contents for manufacturer ID 0xa1.
At the same time, the code was reading the register for manufacturer ID
0x41 (Analog Devices), but it was not using the results. In effect it was
just checking if reading the register returned an error. That doesn't
really add much if any value, so stop doing that.
Fixes: f90be42fb3 ("hwmon: (lm90) Refactor reading of config2 register")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 266423e60e ]
...and gpio-ranges
pinctrl-bcm2835 is a combined pinctrl/gpio driver. Currently the gpio
side is registered first, but this breaks gpio hogs (which are
configured during gpiochip_add_data). Part of the hog initialisation
is a call to pinctrl_gpio_request, and since the pinctrl driver hasn't
yet been registered this results in an -EPROBE_DEFER from which it can
never recover.
Change the initialisation sequence to register the pinctrl driver
first.
This also solves a similar problem with the gpio-ranges property, which
is required in order for released pins to be returned to inputs.
Fixes: 73345a18d4 ("pinctrl: bcm2835: Pass irqchip when adding gpiochip")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211206092237.4105895-2-phil@raspberrypi.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99d7fbb5ce ]
Because platform_get_irq() could fail and return error irq.
Therefore, it might be better to check it if order to avoid the use of
error irq.
Fixes: 797047f875 ("net: ks8851: Implement Parallel bus operations")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb93b3e11d ]
Because platform_get_irq() could fail and return error irq.
Therefore, it might be better to check it if order to avoid the use of
error irq.
Fixes: ae150435b5 ("smsc: Move the SMC (SMSC) drivers")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db6d6afe38 ]
I find that platform_get_irq() will not always succeed.
It will return error irq in case of the failure.
Therefore, it might be better to check it if order to avoid the use of
error irq.
Fixes: 658d439b22 ("fjes: Introduce FUJITSU Extended Socket Network Device driver")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c15b05bae ]
When 802.3ad bond mode is configured the ad_actor_system option is set to
"00:00:00:00:00:00". But when trying to set the all-zeroes MAC as actors'
system address it was failing with EINVAL.
An all-zeroes ethernet address is valid, only multicast addresses are not
valid values.
Fixes: 171a42c38c ("bonding: add netlink support for sys prio, actor sys mac, and port key")
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/20211221111345.2462-1-ffmancera@riseup.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ed1d59211 ]
virtio_net_hdr_set_proto infers skb->protocol from the virtio_net_hdr
gso_type, to avoid packets getting dropped for lack of a proto type.
Its protocol choice is a guess, especially in the case of UFO, where
the single VIRTIO_NET_HDR_GSO_UDP label covers both UFOv4 and UFOv6.
Skip this best effort if the field is already initialized. Whether
explicitly from userspace, or implicitly based on an earlier call to
dev_parse_header_protocol (which is more robust, but was introduced
after this patch).
Fixes: 9d2f67e43b ("net/packet: fix packet drop as of virtio gso")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20211220145027.2784293-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60ec7fcfe7 ]
The return value of kcalloc() needs to be checked.
To avoid dereference of null pointer in case of the failure of alloc.
Therefore, it might be better to change the return type of
qlcnic_sriov_alloc_vlans() and return -ENOMEM when alloc fails and
return 0 the others.
Also, qlcnic_sriov_set_guest_vlan_mode() and __qlcnic_pci_sriov_enable()
should deal with the return value of qlcnic_sriov_alloc_vlans().
Fixes: 154d0c810c ("qlcnic: VLAN enhancement for 84XX adapters")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39e660687a ]
Currently, the imx6q-wandboard Ethernet does not transmit any
data.
This issue has been exposed by commit f5d9aa79df ("ARM: imx6q:
remove clk-out fixup for the Atheros AR8031 and AR8035 PHYs").
Fix it by describing the qca,clk-out-frequency property as suggested
by the commit above.
Fixes: 77591e4245 ("ARM: dts: imx6qdl-wandboard: add ethernet PHY description")
Signed-off-by: Martin Haaß <vvvrrooomm@gmail.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ebb966d3bd ]
In commit 5648b5e116 ("netfilter: nfnetlink_queue: fix OOB when mac
header was cleared"), the test for non-empty MAC header introduced in
commit 2c38de4c1f ("netfilter: fix looped (broad|multi)cast's MAC
handling") has been replaced with a test for a set MAC header.
This breaks the case when the MAC header has been reset (using
skb_reset_mac_header), as is the case with looped-back multicast
packets. As a result, the packets ending up in NFQUEUE get a bogus
hwaddr interpreted from the first bytes of the IP header.
This patch adds a test for a non-empty MAC header in addition to the
test for a set MAC header. The same two tests are also implemented in
nfnetlink_log.c, where the initial code of commit 2c38de4c1f
("netfilter: fix looped (broad|multi)cast's MAC handling") has not been
touched, but where supposedly the same situation may happen.
Fixes: 5648b5e116 ("netfilter: nfnetlink_queue: fix OOB when mac header was cleared")
Signed-off-by: Ignacy Gawędzki <ignacy.gawedzki@green-communications.fr>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9c6e071913 upstream.
Now that we can check out overlapping extents in leaf block and
out-of-order index extents in index block. But the .ee_block in the
first extent of one leaf block should equal to the .ei_block in it's
parent index extent entry. This patch add a check to verify such
inconsistent between the index and leaf block.
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Link: https://lore.kernel.org/r/20210908120850.4012324-3-yi.zhang@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8dd27feced upstream.
After commit 5946d08937 ("ext4: check for overlapping extents in
ext4_valid_extent_entries()"), we can check out the overlapping extent
entry in leaf extent blocks. But the out-of-order extent entry in index
extent blocks could also trigger bad things if the filesystem is
inconsistent. So this patch add a check to figure out the out-of-order
index extents and return error.
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Theodore Ts'o <tytso@mit.edu>
Link: https://lore.kernel.org/r/20210908120850.4012324-2-yi.zhang@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f2f87d51a upstream.
In the most error path of current extents updating operations are not
roll back partial updates properly when some bad things happens(.e.g in
ext4_ext_insert_extent()). So we may get an inconsistent extents tree
if journal has been aborted due to IO error, which may probability lead
to BUGON later when we accessing these extent entries in errors=continue
mode. This patch drop extent buffer's verify flag before updatng the
contents in ext4_ext_get_access(), and reset it after updating in
__ext4_ext_dirty(). After this patch we could force to check the extent
buffer if extents tree updating was break off, make sure the extents are
consistent.
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Theodore Ts'o <tytso@mit.edu>
Link: https://lore.kernel.org/r/20210908120850.4012324-4-yi.zhang@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e6f8d1fa1 upstream.
Similar to
commit 231ad7f409 ("Makefile: infer --target from ARCH for CC=clang")
There really is no point in setting --target based on
$CROSS_COMPILE_COMPAT for clang when the integrated assembler is being
used, since
commit ef94340583 ("arm64: vdso32: drop -no-integrated-as flag").
Allows COMPAT_VDSO to be selected without setting $CROSS_COMPILE_COMPAT
when using clang and lld together.
Before:
$ ARCH=arm64 CROSS_COMPILE_COMPAT=arm-linux-gnueabi- make -j72 LLVM=1 defconfig
$ grep CONFIG_COMPAT_VDSO .config
CONFIG_COMPAT_VDSO=y
$ ARCH=arm64 make -j72 LLVM=1 defconfig
$ grep CONFIG_COMPAT_VDSO .config
$
After:
$ ARCH=arm64 CROSS_COMPILE_COMPAT=arm-linux-gnueabi- make -j72 LLVM=1 defconfig
$ grep CONFIG_COMPAT_VDSO .config
CONFIG_COMPAT_VDSO=y
$ ARCH=arm64 make -j72 LLVM=1 defconfig
$ grep CONFIG_COMPAT_VDSO .config
CONFIG_COMPAT_VDSO=y
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Suggested-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Link: https://lore.kernel.org/r/20211019223646.1146945-5-ndesaulniers@google.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a regression introduced in 131f132203
(see also https://github.com/raspberrypi/linux/issues/4791).
The tc358743 driver refused to bind to the device. The irs1125
driver is likely behaving similarly.
The new unified cam1_clk node that represents the fixed on-board
oscillator is marked as disabled by default. These overlays didn't
expect this and so the clock nodes were stuck in disabled state.
This commit just adds the required status = "okay" line. Other sensor
drivers do this too.
commit be81992f90 upstream.
In case a guest isn't consuming incoming network traffic as fast as it
is coming in, xen-netback is buffering network packages in unlimited
numbers today. This can result in host OOM situations.
Commit f48da8b14d ("xen-netback: fix unlimited guest Rx internal
queue and carrier flapping") meant to introduce a mechanism to limit
the amount of buffered data by stopping the Tx queue when reaching the
data limit, but this doesn't work for cases like UDP.
When hitting the limit don't queue further SKBs, but drop them instead.
In order to be able to tell Rx packages have been dropped increment the
rx_dropped statistics counter in this case.
It should be noted that the old solution to continue queueing SKBs had
the additional problem of an overflow of the 32-bit rx_queue_len value
would result in intermittent Tx queue enabling.
This is part of XSA-392
Fixes: f48da8b14d ("xen-netback: fix unlimited guest Rx internal queue and carrier flapping")
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6032046ec4 upstream.
Commit 1d5d485239 ("xen-netback: require fewer guest Rx slots when
not using GSO") introduced a security problem in netback, as an
interface would only be regarded to be stalled if no slot is available
in the rx queue ring page. In case the SKB at the head of the queued
requests will need more than one rx slot and only one slot is free the
stall detection logic will never trigger, as the test for that is only
looking for at least one slot to be free.
Fix that by testing for the needed number of slots instead of only one
slot being available.
In order to not have to take the rx queue lock that often, store the
number of needed slots in the queue data. As all SKB dequeue operations
happen in the rx queue kernel thread this is safe, as long as the
number of needed slots is accessed via READ/WRITE_ONCE() only and
updates are always done with the rx queue lock held.
Add a small helper for obtaining the number of free slots.
This is part of XSA-392
Fixes: 1d5d485239 ("xen-netback: require fewer guest Rx slots when not using GSO")
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe415186b4 upstream.
The Xen console driver is still vulnerable for an attack via excessive
number of events sent by the backend. Fix that by using a lateeoi event
channel.
For the normal domU initial console this requires the introduction of
bind_evtchn_to_irq_lateeoi() as there is no xenbus device available
at the time the event channel is bound to the irq.
As the decision whether an interrupt was spurious or not requires to
test for bytes having been read from the backend, move sending the
event into the if statement, as sending an event without having found
any bytes to be read is making no sense at all.
This is part of XSA-391
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b27d47950e upstream.
The Xen netfront driver is still vulnerable for an attack via excessive
number of events sent by the backend. Fix that by using lateeoi event
channels.
For being able to detect the case of no rx responses being added while
the carrier is down a new lock is needed in order to update and test
rsp_cons and the number of seen unconsumed responses atomically.
This is part of XSA-391
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0fd08a34e8 upstream.
The Xen blkfront driver is still vulnerable for an attack via excessive
number of events sent by the backend. Fix that by using lateeoi event
channels.
This is part of XSA-391
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b1da99b84 upstream.
Fix drivers/bus/ti-sysc.c:2494:13: error: variable 'error' set but not
used introduced by commit 9d88136120 ("bus: ti-sysc: Add quirk handling
for reinit on context lost").
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f5573cfe7 upstream.
Syzbot triggered the following warning in ovl_workdir_create() ->
ovl_create_real():
if (!err && WARN_ON(!newdentry->d_inode)) {
The reason is that the cgroup2 filesystem returns from mkdir without
instantiating the new dentry.
Weird filesystems such as this will be rejected by overlayfs at a later
stage during setup, but to prevent such a warning, call ovl_mkdir_real()
directly from ovl_workdir_create() and reject this case early.
Reported-and-tested-by: syzbot+75eab84fd0af9e8bf66b@syzkaller.appspotmail.com
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 44870a9e7a upstream.
Syzbot reported, that mxl111sf_ctrl_msg() uses uninitialized
mutex. The problem was in wrong mutex_init() location.
Previous mutex_init(&state->msg_lock) call was in ->init() function, but
dvb_usbv2_init() has this order of calls:
dvb_usbv2_init()
dvb_usbv2_adapter_init()
dvb_usbv2_adapter_frontend_init()
props->frontend_attach()
props->init()
Since mxl111sf_* devices call mxl111sf_ctrl_msg() in ->frontend_attach()
internally we need to initialize state->msg_lock before
frontend_attach(). To achieve it, ->probe() call added to all mxl111sf_*
devices, which will simply initiaize mutex.
Reported-and-tested-by: syzbot+5ca0bf339f13c4243001@syzkaller.appspotmail.com
Fixes: 8572211842 ("[media] mxl111sf: convert to new DVB USB")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd0687c18e upstream.
Do not sleep in poll() when the need_wakeup flag is set. When this
flag is set, the application needs to explicitly wake up the driver
with a syscall (poll, recvmsg, sendmsg, etc.) to guarantee that Rx
and/or Tx processing will be processed promptly. But the current code
in poll(), sleeps first then wakes up the driver. This means that no
driver processing will occur (baring any interrupts) until the timeout
has expired.
Fix this by checking the need_wakeup flag first and if set, wake the
driver and return to the application. Only if need_wakeup is not set
should the process sleep if there is a timeout set in the poll() call.
Fixes: 77cd0d7b3f ("xsk: add support for need_wakeup flag in AF_XDP rings")
Reported-by: Keith Wiles <keith.wiles@intel.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/bpf/20211214102607.7677-1-magnus.karlsson@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 737e65c795 upstream.
According to the i.MX6ULL Reference Manual, pad CSI_DATA07 may
have the ESAI_TX0 functionality, not ESAI_T0.
Also, NXP's i.MX Config Tools 10.0 generates dtsi with the
MX6ULL_PAD_CSI_DATA07__ESAI_TX0 naming, so fix it accordingly.
There are no devicetree users in mainline that use the old name,
so just remove the old entry.
Fixes: c201369d4a ("ARM: dts: imx6ull: add imx6ull support")
Reported-by: George Makarov <georgemakarov1@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a02dcde595 upstream.
A new warning in clang points out a few places in this driver where a
bitwise OR is being used with boolean types:
drivers/input/touchscreen.c:81:17: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
data_present = touchscreen_get_prop_u32(dev, "touchscreen-min-x",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
This use of a bitwise OR is intentional, as bitwise operations do not
short circuit, which allows all the calls to touchscreen_get_prop_u32()
to happen so that the last parameter is initialized while coalescing the
results of the calls to make a decision after they are all evaluated.
To make this clearer to the compiler, use the '|=' operator to assign
the result of each touchscreen_get_prop_u32() call to data_present,
which keeps the meaning of the code the same but makes it obvious that
every one of these calls is expected to happen.
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20211014205757.3474635-1-nathan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e8c11b6b3 upstream.
Even after commit e1d7ba8735 ("time: Always make sure wall_to_monotonic
isn't positive") it is still possible to make wall_to_monotonic positive
by running the following code:
int main(void)
{
struct timespec time;
clock_gettime(CLOCK_MONOTONIC, &time);
time.tv_nsec = 0;
clock_settime(CLOCK_REALTIME, &time);
return 0;
}
The reason is that the second parameter of timespec64_compare(), ts_delta,
may be unnormalized because the delta is calculated with an open coded
substraction which causes the comparison of tv_sec to yield the wrong
result:
wall_to_monotonic = { .tv_sec = -10, .tv_nsec = 900000000 }
ts_delta = { .tv_sec = -9, .tv_nsec = -900000000 }
That makes timespec64_compare() claim that wall_to_monotonic < ts_delta,
but actually the result should be wall_to_monotonic > ts_delta.
After normalization, the result of timespec64_compare() is correct because
the tv_sec comparison is not longer misleading:
wall_to_monotonic = { .tv_sec = -10, .tv_nsec = 900000000 }
ts_delta = { .tv_sec = -10, .tv_nsec = 100000000 }
Use timespec64_sub() to ensure that ts_delta is normalized, which fixes the
issue.
Fixes: e1d7ba8735 ("time: Always make sure wall_to_monotonic isn't positive")
Signed-off-by: Yu Liao <liaoyu15@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211213135727.1656662-1-liaoyu15@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c33ff7288 upstream.
Commit fab8a02b73 ("serial: 8250_fintek: Enable high speed mode on Fintek F81866")
introduced support to use high baudrate with Fintek SuperIO UARTs. It'll
change clocksources when the UART probed.
But when user add kernel parameter "console=ttyS0,115200 console=tty0" to make
the UART as console output, the console will output garbled text after the
following kernel message.
[ 3.681188] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
The issue is occurs in following step:
probe_setup_port() -> fintek_8250_goto_highspeed()
It change clocksource from 115200 to 921600 with wrong time, it should change
clocksource in set_termios() not in probed. The following 3 patches are
implemented change clocksource in fintek_8250_set_termios().
Commit 58178914ae ("serial: 8250_fintek: UART dynamic clocksource on Fintek F81216H")
Commit 195638b6d4 ("serial: 8250_fintek: UART dynamic clocksource on Fintek F81866")
Commit 423d9118c6 ("serial: 8250_fintek: Add F81966 Support")
Due to the high baud rate had implemented above 3 patches and the patch
Commit fab8a02b73 ("serial: 8250_fintek: Enable high speed mode on Fintek F81866")
is bugged, So this patch will remove it.
Fixes: fab8a02b73 ("serial: 8250_fintek: Enable high speed mode on Fintek F81866")
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Link: https://lore.kernel.org/r/20211215075835.2072-1-hpeter+linux_kernel@gmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit edaa26334c upstream.
The donation calculation logic assumes that the donor has non-zero
after-donation hweight, so the lowest active hweight a donating cgroup can
have is 2 so that it can donate 1 while keeping the other 1 for itself.
Earlier, we only donated from cgroups with sizable surpluses so this
condition was always true. However, with the precise donation algorithm
implemented, f1de2439ec ("blk-iocost: revamp donation amount
determination") made the donation amount calculation exact enabling even low
hweight cgroups to donate.
This means that in rare occasions, a cgroup with active hweight of 1 can
enter donation calculation triggering the following warning and then a
divide-by-zero oops.
WARNING: CPU: 4 PID: 0 at block/blk-iocost.c:1928 transfer_surpluses.cold+0x0/0x53 [884/94867]
...
RIP: 0010:transfer_surpluses.cold+0x0/0x53
Code: 92 ff 48 c7 c7 28 d1 ab b5 65 48 8b 34 25 00 ae 01 00 48 81 c6 90 06 00 00 e8 8b 3f fe ff 48 c7 c0 ea ff ff ff e9 95 ff 92 ff <0f> 0b 48 c7 c7 30 da ab b5 e8 71 3f fe ff 4c 89 e8 4d 85 ed 74 0
4
...
Call Trace:
<IRQ>
ioc_timer_fn+0x1043/0x1390
call_timer_fn+0xa1/0x2c0
__run_timers.part.0+0x1ec/0x2e0
run_timer_softirq+0x35/0x70
...
iocg: invalid donation weights in /a/b: active=1 donating=1 after=0
Fix it by excluding cgroups w/ active hweight < 2 from donating. Excluding
these extreme low hweight donations shouldn't affect work conservation in
any meaningful way.
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: f1de2439ec ("blk-iocost: revamp donation amount determination")
Cc: stable@vger.kernel.org # v5.10+
Link: https://lore.kernel.org/r/Ybfh86iSvpWKxhVM@slm.duckdns.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33fab97249 upstream.
When creating a subvolume, at create_subvol(), we allocate an anonymous
device and later call btrfs_get_new_fs_root(), which in turn just calls
btrfs_get_root_ref(). There we call btrfs_init_fs_root() which assigns
the anonymous device to the root, but if after that call there's an error,
when we jump to 'fail' label, we call btrfs_put_root(), which frees the
anonymous device and then returns an error that is propagated back to
create_subvol(). Than create_subvol() frees the anonymous device again.
When this happens, if the anonymous device was not reallocated after
the first time it was freed with btrfs_put_root(), we get a kernel
message like the following:
(...)
[13950.282466] BTRFS: error (device dm-0) in create_subvol:663: errno=-5 IO failure
[13950.283027] ida_free called for id=65 which is not allocated.
[13950.285974] BTRFS info (device dm-0): forced readonly
(...)
If the anonymous device gets reallocated by another btrfs filesystem
or any other kernel subsystem, then bad things can happen.
So fix this by setting the root's anonymous device to 0 at
btrfs_get_root_ref(), before we call btrfs_put_root(), if an error
happened.
Fixes: 2dfb1e43f5 ("btrfs: preallocate anon block device at first phase of snapshot creation")
CC: stable@vger.kernel.org # 5.10+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f35838a693 upstream.
Line 1169 (#3) allocates a memory chunk for victim_name by kmalloc(),
but when the function returns in line 1184 (#4) victim_name allocated
by line 1169 (#3) is not freed, which will lead to a memory leak.
There is a similar snippet of code in this function as allocating a memory
chunk for victim_name in line 1104 (#1) as well as releasing the memory
in line 1116 (#2).
We should kfree() victim_name when the return value of backref_in_log()
is less than zero and before the function returns in line 1184 (#4).
1057 static inline int __add_inode_ref(struct btrfs_trans_handle *trans,
1058 struct btrfs_root *root,
1059 struct btrfs_path *path,
1060 struct btrfs_root *log_root,
1061 struct btrfs_inode *dir,
1062 struct btrfs_inode *inode,
1063 u64 inode_objectid, u64 parent_objectid,
1064 u64 ref_index, char *name, int namelen,
1065 int *search_done)
1066 {
1104 victim_name = kmalloc(victim_name_len, GFP_NOFS);
// #1: kmalloc (victim_name-1)
1105 if (!victim_name)
1106 return -ENOMEM;
1112 ret = backref_in_log(log_root, &search_key,
1113 parent_objectid, victim_name,
1114 victim_name_len);
1115 if (ret < 0) {
1116 kfree(victim_name); // #2: kfree (victim_name-1)
1117 return ret;
1118 } else if (!ret) {
1169 victim_name = kmalloc(victim_name_len, GFP_NOFS);
// #3: kmalloc (victim_name-2)
1170 if (!victim_name)
1171 return -ENOMEM;
1180 ret = backref_in_log(log_root, &search_key,
1181 parent_objectid, victim_name,
1182 victim_name_len);
1183 if (ret < 0) {
1184 return ret; // #4: missing kfree (victim_name-2)
1185 } else if (!ret) {
1241 return 0;
1242 }
Fixes: d3316c8233 ("btrfs: Properly handle backref_in_log retval")
CC: stable@vger.kernel.org # 5.10+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Jianglei Nie <niejianglei2021@163.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 83b67041f3 upstream.
When generalising GPIO support and adding support for CP2102N, the GPIO
registration for some CP2105 devices accidentally broke. Specifically,
when all the pins of a port are in "modem" mode, and thus unavailable
for GPIO use, the GPIO chip would now be registered without having
initialised the number of GPIO lines. This would in turn be rejected by
gpiolib and some errors messages would be printed (but importantly probe
would still succeed).
Fix this by initialising the number of GPIO lines before registering the
GPIO chip.
Note that as for the other device types, and as when all CP2105 pins are
muxed for LED function, the GPIO chip is registered also when no pins
are available for GPIO use.
Reported-by: Maarten Brock <m.brock@vanmierlo.com>
Link: https://lore.kernel.org/r/5eb560c81d2ea1a2b4602a92d9f48a89@vanmierlo.com
Fixes: c8acfe0aad ("USB: serial: cp210x: implement GPIO support for CP2102N")
Cc: stable@vger.kernel.org # 4.19
Cc: Karoly Pados <pados@pados.hu>
Link: https://lore.kernel.org/r/20211126094348.31698-1-johan@kernel.org
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Maarten Brock <m.brock@vanmierlo.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 83dbf898a2 upstream.
Masking all unused MSI-X entries is done to ensure that a crash kernel
starts from a clean slate, which correponds to the reset state of the
device as defined in the PCI-E specificion 3.0 and later:
Vector Control for MSI-X Table Entries
--------------------------------------
"00: Mask bit: When this bit is set, the function is prohibited from
sending a message using this MSI-X Table entry.
...
This bit’s state after reset is 1 (entry is masked)."
A Marvell NVME device fails to deliver MSI interrupts after trying to
enable MSI-X interrupts due to that masking. It seems to take the MSI-X
mask bits into account even when MSI-X is disabled.
While not specification compliant, this can be cured by moving the masking
into the success path, so that the MSI-X table entries stay in device reset
state when the MSI-X setup fails.
[ tglx: Move it into the success path, add comment and amend changelog ]
Fixes: aa8092c1d1 ("PCI/MSI: Mask all unused MSI-X entries")
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-pci@vger.kernel.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211210161025.3287927-1-sr@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fac6bf87c5 upstream.
When activate_stm_id_vb_detection is enabled, ID and Vbus detection relies
on sensing comparators. This detection needs time to stabilize.
A delay was already applied in dwc2_resume() when reactivating the
detection, but it wasn't done in dwc2_probe().
This patch adds delay after enabling STM ID/VBUS detection. Then, ID state
is good when initializing gadget and host, and avoid to get a wrong
Connector ID Status Change interrupt.
Fixes: a415083a11 ("usb: dwc2: add support for STM32MP15 SoCs USB OTG HS and FS")
Cc: stable <stable@vger.kernel.org>
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211207124510.268841-1-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1aa2abb33a ]
The ability to write to MSR_IA32_PERF_CAPABILITIES from the host should
not depend on guest visible CPUID entries, even if just to allow
creating/restoring guest MSRs and CPUIDs in any sequence.
Fixes: 27461da310 ("KVM: x86/pmu: Support full width counting")
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20211216165213.338923-3-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f08adf5add ]
Szymon rightly pointed out that the previous check for the endpoint
direction in bRequestType was not looking at only the bit involved, but
rather the whole value. Normally this is ok, but for some request
types, bits other than bit 8 could be set and the check for the endpoint
length could not stall correctly.
Fix that up by only checking the single bit.
Fixes: 153a2d7e33 ("USB: gadget: detect too-big endpoint 0 requests")
Cc: Felipe Balbi <balbi@kernel.org>
Reported-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Link: https://lore.kernel.org/r/20211214184621.385828-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2fcbf81c3 ]
The libbpf CI reported occasional failure in btf_skc_cls_ingress:
test_syncookie:FAIL:Unexpected syncookie states gen_cookie:80326634 recv_cookie:0
bpf prog error at line 97
"error at line 97" means the bpf prog cannot find the listening socket
when the final ack is received. It then skipped processing
the syncookie in the final ack which then led to "recv_cookie:0".
The problem is the userspace program did not do accept() and went
ahead to close(listen_fd) before the kernel (and the bpf prog) had
a chance to process the final ack.
The fix is to add accept() call so that the userspace will wait for
the kernel to finish processing the final ack first before close()-ing
everything.
Fixes: 9a856cae22 ("bpf: selftest: Add test_btf_skc_cls_ingress")
Reported-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20211216191630.466151-1-kafai@fb.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b8e6e7824 ]
The descriptor list is a shared resource across all of the transmit queues, and
the locking mechanism used today only protects concurrency across a given
transmit queue between the transmit and reclaiming. This creates an opportunity
for the SYSTEMPORT hardware to work on corrupted descriptors if we have
multiple producers at once which is the case when using multiple transmit
queues.
This was particularly noticeable when using multiple flows/transmit queues and
it showed up in interesting ways in that UDP packets would get a correct UDP
header checksum being calculated over an incorrect packet length. Similarly TCP
packets would get an equally correct checksum computed by the hardware over an
incorrect packet length.
The SYSTEMPORT hardware maintains an internal descriptor list that it re-arranges
when the driver produces a new descriptor anytime it writes to the
WRITE_PORT_{HI,LO} registers, there is however some delay in the hardware to
re-organize its descriptors and it is possible that concurrent TX queues
eventually break this internal allocation scheme to the point where the
length/status part of the descriptor gets used for an incorrect data buffer.
The fix is to impose a global serialization for all TX queues in the short
section where we are writing to the WRITE_PORT_{HI,LO} registers which solves
the corruption even with multiple concurrent TX queues being used.
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211215202450.4086240-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c15b3123f ]
In nginx/wrk benchmark, there's a hung problem with high probability
on case likes that: (client will last several minutes to exit)
server: smc_run nginx
client: smc_run wrk -c 10000 -t 1 http://server
Client hangs with the following backtrace:
0 [ffffa7ce8Of3bbf8] __schedule at ffffffff9f9eOd5f
1 [ffffa7ce8Of3bc88] schedule at ffffffff9f9eløe6
2 [ffffa7ce8Of3bcaO] schedule_timeout at ffffffff9f9e3f3c
3 [ffffa7ce8Of3bd2O] wait_for_common at ffffffff9f9el9de
4 [ffffa7ce8Of3bd8O] __flush_work at ffffffff9fOfeOl3
5 [ffffa7ce8øf3bdfO] smc_release at ffffffffcO697d24 [smc]
6 [ffffa7ce8Of3be2O] __sock_release at ffffffff9f8O2e2d
7 [ffffa7ce8Of3be4ø] sock_close at ffffffff9f8ø2ebl
8 [ffffa7ce8øf3be48] __fput at ffffffff9f334f93
9 [ffffa7ce8Of3be78] task_work_run at ffffffff9flOlff5
10 [ffffa7ce8Of3beaO] do_exit at ffffffff9fOe5Ol2
11 [ffffa7ce8Of3bflO] do_group_exit at ffffffff9fOe592a
12 [ffffa7ce8Of3bf38] __x64_sys_exit_group at ffffffff9fOe5994
13 [ffffa7ce8Of3bf4O] do_syscall_64 at ffffffff9f9d4373
14 [ffffa7ce8Of3bfsO] entry_SYSCALL_64_after_hwframe at ffffffff9fa0007c
This issue dues to flush_work(), which is used to wait for
smc_connect_work() to finish in smc_release(). Once lots of
smc_connect_work() was pending or all executing work dangling,
smc_release() has to block until one worker comes to free, which
is equivalent to wait another smc_connnect_work() to finish.
In order to fix this, There are two changes:
1. For those idle smc_connect_work(), cancel it from the workqueue; for
executing smc_connect_work(), waiting for it to finish. For that
purpose, replace flush_work() with cancel_work_sync().
2. Since smc_connect() hold a reference for passive closing, if
smc_connect_work() has been cancelled, release the reference.
Fixes: 24ac3a08e6 ("net/smc: rebuild nonblocking connect")
Reported-by: Tony Lu <tonylu@linux.alibaba.com>
Tested-by: Dust Li <dust.li@linux.alibaba.com>
Reviewed-by: Dust Li <dust.li@linux.alibaba.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Link: https://lore.kernel.org/r/1639571361-101128-1-git-send-email-alibuda@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a03ef676a ]
When printing netdev features %pNF already takes care of the 0x prefix,
remove the explicit one.
Fixes: 6413139dfc ("skbuff: increase verbosity when dumping skb data")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 407ecd1bd7 ]
The return value of kmalloc() needs to be checked.
To avoid use in efx_nic_update_stats() in case of the failure of alloc.
Fixes: b593b6f1b4 ("sfc_ef100: statistics gathering")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 481221775d ]
Zero-initialize memory for new map's value in function nsim_bpf_map_alloc
since it may cause a potential kernel information leak issue, as follows:
1. nsim_bpf_map_alloc calls nsim_map_alloc_elem to allocate elements for
a new map.
2. nsim_map_alloc_elem uses kmalloc to allocate map's value, but doesn't
zero it.
3. A user application can use IOCTL BPF_MAP_LOOKUP_ELEM to get specific
element's information in the map.
4. The kernel function map_lookup_elem will call bpf_map_copy_value to get
the information allocated at step-2, then use copy_to_user to copy to the
user buffer.
This can only leak information for an array map.
Fixes: 395cacb5f1 ("netdevsim: bpf: support fake map offload")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Haimin Zhang <tcs.kernel@gmail.com>
Link: https://lore.kernel.org/r/20211215111530.72103-1-tcs.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf0a375055 ]
The MDIO bus speed must be initialized before talking to the PHY the first
time in order to avoid talking to it using a speed that the PHY doesn't
support.
This fixes HW initialization error -17 (IXGBE_ERR_PHY_ADDR_INVALID) on
Denverton CPUs (a.k.a. the Atom C3000 family) on ports with a 10Gb network
plugged in. On those devices, HLREG0[MDCSPD] resets to 1, which combined
with the 10Gb network results in a 24MHz MDIO speed, which is apparently
too fast for the connected PHY. PHY register reads over MDIO bus return
garbage, leading to initialization failure.
Reproduced with Linux kernel 4.19 and 5.15-rc7. Can be reproduced using
the following setup:
* Use an Atom C3000 family system with at least one X552 LAN on the SoC
* Disable PXE or other BIOS network initialization if possible
(the interface must not be initialized before Linux boots)
* Connect a live 10Gb Ethernet cable to an X550 port
* Power cycle (not reset, doesn't always work) the system and boot Linux
* Observe: ixgbe interfaces w/ 10GbE cables plugged in fail with error -17
Fixes: e84db72727 ("ixgbe: Introduce function to control MDIO speed")
Signed-off-by: Cyril Novikov <cnovikov@lynx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 271225fd57 ]
Commit a296d665ea ("ixgbe: Add ethtool support to enable 2.5 and 5.0
Gbps support") introduced suppression of the advertisement of NBASE-T
speeds by default, according to Todd Fujinaka to accommodate customers
with network switches which could not cope with advertised NBASE-T
speeds, as posted in the E1000-devel mailing list:
https://sourceforge.net/p/e1000/mailman/message/37106269/
However, the suppression was not documented at all, nor was how to
enable NBASE-T support.
Properly document the NBASE-T suppression and how to enable NBASE-T
support.
Fixes: a296d665ea ("ixgbe: Add ethtool support to enable 2.5 and 5.0 Gbps support")
Reported-by: Robert Schlabbach <robert_s@gmx.net>
Signed-off-by: Robert Schlabbach <robert_s@gmx.net>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0182d1f3fa ]
The LTR maximum value was incorrectly written using the scale from
the LTR minimum value. This would cause incorrect values to be sent,
in cases where the initial calculation lead to different min/max scales.
Fixes: 707abf0695 ("igc: Add initial LTR support")
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6d335a60d ]
In `igbvf_probe`, if register_netdev() fails, the program will go to
label err_hw_init, and then to label err_ioremap. In free_netdev() which
is just below label err_ioremap, there is `list_for_each_entry_safe` and
`netif_napi_del` which aims to delete all entries in `dev->napi_list`.
The program has added an entry `adapter->rx_ring->napi` which is added by
`netif_napi_add` in igbvf_alloc_queues(). However, adapter->rx_ring has
been freed below label err_hw_init. So this a UAF.
In terms of how to patch the problem, we can refer to igbvf_remove() and
delete the entry before `adapter->rx_ring`.
The KASAN logs are as follows:
[ 35.126075] BUG: KASAN: use-after-free in free_netdev+0x1fd/0x450
[ 35.127170] Read of size 8 at addr ffff88810126d990 by task modprobe/366
[ 35.128360]
[ 35.128643] CPU: 1 PID: 366 Comm: modprobe Not tainted 5.15.0-rc2+ #14
[ 35.129789] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014
[ 35.131749] Call Trace:
[ 35.132199] dump_stack_lvl+0x59/0x7b
[ 35.132865] print_address_description+0x7c/0x3b0
[ 35.133707] ? free_netdev+0x1fd/0x450
[ 35.134378] __kasan_report+0x160/0x1c0
[ 35.135063] ? free_netdev+0x1fd/0x450
[ 35.135738] kasan_report+0x4b/0x70
[ 35.136367] free_netdev+0x1fd/0x450
[ 35.137006] igbvf_probe+0x121d/0x1a10 [igbvf]
[ 35.137808] ? igbvf_vlan_rx_add_vid+0x100/0x100 [igbvf]
[ 35.138751] local_pci_probe+0x13c/0x1f0
[ 35.139461] pci_device_probe+0x37e/0x6c0
[ 35.165526]
[ 35.165806] Allocated by task 366:
[ 35.166414] ____kasan_kmalloc+0xc4/0xf0
[ 35.167117] foo_kmem_cache_alloc_trace+0x3c/0x50 [igbvf]
[ 35.168078] igbvf_probe+0x9c5/0x1a10 [igbvf]
[ 35.168866] local_pci_probe+0x13c/0x1f0
[ 35.169565] pci_device_probe+0x37e/0x6c0
[ 35.179713]
[ 35.179993] Freed by task 366:
[ 35.180539] kasan_set_track+0x4c/0x80
[ 35.181211] kasan_set_free_info+0x1f/0x40
[ 35.181942] ____kasan_slab_free+0x103/0x140
[ 35.182703] kfree+0xe3/0x250
[ 35.183239] igbvf_probe+0x1173/0x1a10 [igbvf]
[ 35.184040] local_pci_probe+0x13c/0x1f0
Fixes: d4e0fe01a3 (igbvf: add new driver to support 82576 virtual functions)
Reported-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Letu Ren <fantasquex@gmail.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 584af82154 ]
Move checking condition of VF MAC filter before clearing
or adding MAC filter to VF to prevent potential blackout caused
by removal of necessary and working VF's MAC filter.
Fixes: 1b8b062a99 ("igb: add VF trust infrastructure")
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a708376361 ]
A new warning in clang points out two instances where boolean
expressions are being used with a bitwise OR instead of logical OR:
drivers/soc/tegra/fuse/speedo-tegra20.c:72:9: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
reg = tegra_fuse_read_spare(i) |
^~~~~~~~~~~~~~~~~~~~~~~~~~
||
drivers/soc/tegra/fuse/speedo-tegra20.c:72:9: note: cast one or both operands to int to silence this warning
drivers/soc/tegra/fuse/speedo-tegra20.c:87:9: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
reg = tegra_fuse_read_spare(i) |
^~~~~~~~~~~~~~~~~~~~~~~~~~
||
drivers/soc/tegra/fuse/speedo-tegra20.c:87:9: note: cast one or both operands to int to silence this warning
2 warnings generated.
The motivation for the warning is that logical operations short circuit
while bitwise operations do not.
In this instance, tegra_fuse_read_spare() is not semantically returning
a boolean, it is returning a bit value. Use u32 for its return type so
that it can be used with either bitwise or boolean operators without any
warnings.
Fixes: 25cd5a3914 ("ARM: tegra: Add speedo-based process identification")
Link: https://github.com/ClangBuiltLinux/linux/issues/1488
Suggested-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6692b3b97 ]
The mptcp ULP extension relies on sk->sk_sock_kern being set correctly:
It prevents setsockopt(fd, IPPROTO_TCP, TCP_ULP, "mptcp", 6); from
working for plain tcp sockets (any userspace-exposed socket).
But in case of fallback, accept() can return a plain tcp sk.
In such case, sk is still tagged as 'kernel' and setsockopt will work.
This will crash the kernel, The subflow extension has a NULL ctx->conn
mptcp socket:
BUG: KASAN: null-ptr-deref in subflow_data_ready+0x181/0x2b0
Call Trace:
tcp_data_ready+0xf8/0x370
[..]
Fixes: cf7da0d66c ("mptcp: Create SUBFLOW socket for incoming connections")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa464957f7 ]
Memory is allocated for gpu_metrics_table in renoir_init_smc_tables(),
but not freed in int smu_v12_0_fini_smc_tables(). Free it!
Fixes: 95868b8576 ("drm/amd/powerplay: add Renoir support for gpu metrics export")
Signed-off-by: Lang Yu <lang.yu@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 166b6a46b7 ]
We need to return EOPNOTSUPP for the unsupported mpls action type when
setup the flow action.
In the original implement, we will return 0 for the unsupported mpls
action type, actually we do not setup it and the following actions
to the flow action entry.
Fixes: 9838b20a7f ("net: sched: take rtnl lock in tc_setup_flow_action()")
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71da1aec21 ]
The recent GRE selftests defined NUM_NETIFS=10. If the users copy
forwarding.config.sample to forwarding.config directly, they will get
error "Command line is not complete" when run the GRE tests, because
create_netif_veth() failed with no interface name defined.
Fix it by extending the NETIFS with p9 and p10.
Fixes: 2800f24854 ("selftests: forwarding: Test multipath hashing on inner IP pkts for GRE tunnel")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28a2686c18 ]
IPv6 allows binding a socket to a device then binding to an address
not on the device (__inet6_bind -> ipv6_chk_addr with strict flag
not set). Update the bind tests to reflect legacy behavior.
Fixes: 34d0302ab8 ("selftests: Add ipv6 address bind tests to fcnal-test")
Reported-by: Li Zhijian <lizhijian@fujitsu.com>
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f108ae445 ]
Commit referenced below added negative socket bind tests for VRF. The
socket binds should fail since the address to bind to is in a VRF yet
the socket is not bound to the VRF or a device within it. Update the
expected return code to check for 1 (bind failure) so the test passes
when the bind fails as expected. Add a 'show_hint' comment to explain
why the bind is expected to fail.
Fixes: 75b2b2b3db ("selftests: Add ipv4 address bind tests to fcnal-test")
Reported-by: Li Zhijian <lizhijian@fujitsu.com>
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e0147592b ]
Commit referenced below added configuration in the default VRF that
duplicates a VRF to check MD5 passwords are properly used and fail
when expected. That config should not be added all the time as it
can cause tests to pass that should not (by matching on default VRF
setup when it should not). Move the duplicate setup to a function
that is only called for the MD5 tests and add a cleanup function
to remove it after the MD5 tests.
Fixes: 5cad8bce26 ("fcnal-test: Add TCP MD5 tests for VRF")
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27cbf64a76 ]
Currently, the hns3_remove function firstly uninstall client instance,
and then uninstall acceletion engine device. The netdevice is freed in
client instance uninstall process, but acceletion engine device uninstall
process still use it to trace runtime information. This causes a use after
free problem.
So fixes it by check the instance register state to avoid use after free.
Fixes: d8355240cf ("net: hns3: add trace event support for PF/VF mailbox")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41967a37b8 ]
arch_kexec_apply_relocations_add currently ignores all errors returned
by arch_kexec_do_relocs. This means that every unknown relocation is
silently skipped causing unpredictable behavior while the relocated code
runs. Fix this by checking for errors and fail kexec_file_load if an
unknown relocation type is encountered.
The problem was found after gcc changed its behavior and used
R_390_PLT32DBL relocations for brasl instruction and relied on ld to
resolve the relocations in the final link in case direct calls are
possible. As the purgatory code is only linked partially (option -r)
ld didn't resolve the relocations leaving them for arch_kexec_do_relocs.
But arch_kexec_do_relocs doesn't know how to handle R_390_PLT32DBL
relocations so they were silently skipped. This ultimately caused an
endless loop in the purgatory as the brasl instructions kept branching
to itself.
Fixes: 71406883fd ("s390/kexec_file: Add kexec_file_load system call")
Reported-by: Tao Liu <ltao@redhat.com>
Signed-off-by: Philipp Rudo <prudo@redhat.com>
Link: https://lore.kernel.org/r/20211208130741.5821-3-prudo@redhat.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1db8f5fc2e ]
The VMADDR_CID_ANY flag used by a socket means that the socket isn't bound
to any specific CID. For example, a host vsock server may want to be bound
with VMADDR_CID_ANY, so that a guest vsock client can connect to the host
server with CID=VMADDR_CID_HOST (i.e. 2), and meanwhile, a host vsock
client can connect to the same local server with CID=VMADDR_CID_LOCAL
(i.e. 1).
The current implementation sets the destination socket's svm_cid to a
fixed CID value after the first client's connection, which isn't an
expected operation. For example, if the guest client first connects to the
host server, the server's svm_cid gets set to VMADDR_CID_HOST, then other
host clients won't be able to connect to the server anymore.
Reproduce steps:
1. Run the host server:
socat VSOCK-LISTEN:1234,fork -
2. Run a guest client to connect to the host server:
socat - VSOCK-CONNECT:2:1234
3. Run a host client to connect to the host server:
socat - VSOCK-CONNECT:1:1234
Without this patch, step 3. above fails to connect, and socat complains
"socat[1720] E connect(5, AF=40 cid:1 port:1234, 16): Connection
reset by peer".
With this patch, the above works well.
Fixes: c0cfa2d8a7 ("vsock: add multi-transports support")
Signed-off-by: Wei Wang <wei.w.wang@intel.com>
Link: https://lore.kernel.org/r/20211126011823.1760-1-wei.w.wang@intel.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ebd29f916 ]
At the moment, using the ARM32 multi_v7_defconfig always results in two
SoCs being exposed in sysfs. This is wrong, as far as I'm aware the
Qualcomm DragonBoard 410c does not actually make use of a i.MX SoC. :)
qcom-db410c:/sys/devices/soc0$ grep . *
family:Freescale i.MX
machine:Qualcomm Technologies, Inc. APQ 8016 SBC
revision:0.0
serial_number:0000000000000000
soc_id:Unknown
qcom-db410c:/sys/devices/soc1$ grep . *
family:Snapdragon
machine:APQ8016
...
This happens because imx_soc_device_init() registers the soc device
unconditionally, even when running on devices that do not make use of i.MX.
Arnd already reported this more than a year ago and even suggested a fix
similar to this commit, but for some reason it was never submitted.
Fix it by checking if the "__mxc_cpu_type" variable was actually
initialized by earlier platform code. On devices without i.MX it will
simply stay 0.
Cc: Peng Fan <peng.fan@nxp.com>
Fixes: d2199b3487 ("ARM: imx: use device_initcall for imx_soc_device_init")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/CAK8P3a0hxO1TmK6oOMQ70AHSWJnP_CAq57YMOutrxkSYNjFeuw@mail.gmail.com/
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54baf56eaa ]
Before commit fc0c209c14 ("clk: Allow parents to be specified without
string names") child clks couldn't find their parent until the parent
clk was added to a list in __clk_core_init(). After that commit, child
clks can reference their parent clks directly via a clk_hw pointer, or
they can lookup that clk_hw pointer via DT if the parent clk is
registered with an OF clk provider.
The common clk framework treats hw->core being non-NULL as "the clk is
registered" per the logic within clk_core_fill_parent_index():
parent = entry->hw->core;
/*
* We have a direct reference but it isn't registered yet?
* Orphan it and let clk_reparent() update the orphan status
* when the parent is registered.
*/
if (!parent)
Therefore we need to be extra careful to not set hw->core until the clk
is fully registered with the clk framework. Otherwise we can get into a
situation where a child finds a parent clk and we move the child clk off
the orphan list when the parent isn't actually registered, wrecking our
enable accounting and breaking critical clks.
Consider the following scenario:
CPU0 CPU1
---- ----
struct clk_hw clkBad;
struct clk_hw clkA;
clkA.init.parent_hws = { &clkBad };
clk_hw_register(&clkA) clk_hw_register(&clkBad)
... __clk_register()
hw->core = core
...
__clk_register()
__clk_core_init()
clk_prepare_lock()
__clk_init_parent()
clk_core_get_parent_by_index()
clk_core_fill_parent_index()
if (entry->hw) {
parent = entry->hw->core;
At this point, 'parent' points to clkBad even though clkBad hasn't been
fully registered yet. Ouch! A similar problem can happen if a clk
controller registers orphan clks that are referenced in the DT node of
another clk controller.
Let's fix all this by only setting the hw->core pointer underneath the
clk prepare lock in __clk_core_init(). This way we know that
clk_core_fill_parent_index() can't see hw->core be non-NULL until the
clk is fully registered.
Fixes: fc0c209c14 ("clk: Allow parents to be specified without string names")
Signed-off-by: Mike Tipton <quic_mdtipton@quicinc.com>
Link: https://lore.kernel.org/r/20211109043438.4639-1-quic_mdtipton@quicinc.com
[sboyd@kernel.org: Reword commit text, update comment]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee2a095d3b ]
The smatch static checker warned about an uninitialized symbol usage in
this function, in the case where ceph_mdsc_build_path returns an error.
It turns out that that case is harmless, but it just looks sketchy.
Initialize the variable at declaration time, and remove the unneeded
setting of it later.
Fixes: a33f6432b3 ("ceph: encode inodes' parent/d_name in cap reconnect message")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 973e524563 ]
opened_inodes is incremented twice when the same inode is opened twice
with O_RDONLY and O_WRONLY respectively.
To reproduce, run this python script, then check the metrics:
import os
for _ in range(10000):
fd_r = os.open('a', os.O_RDONLY)
fd_w = os.open('a', os.O_WRONLY)
os.close(fd_r)
os.close(fd_w)
Fixes: 1dd8d47081 ("ceph: metrics for opened files, pinned caps and opened inodes")
Signed-off-by: Hu Weiwen <sehuww@mail.scut.edu.cn>
Reviewed-by: Xiubo Li <xiubli@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f4b3ee3c85 upstream.
If the audit daemon were ever to get stuck in a stopped state the
kernel's kauditd_thread() could get blocked attempting to send audit
records to the userspace audit daemon. With the kernel thread
blocked it is possible that the audit queue could grow unbounded as
certain audit record generating events must be exempt from the queue
limits else the system enter a deadlock state.
This patch resolves this problem by lowering the kernel thread's
socket sending timeout from MAX_SCHEDULE_TIMEOUT to HZ/10 and tweaks
the kauditd_send_queue() function to better manage the various audit
queues when connection problems occur between the kernel and the
audit daemon. With this patch, the backlog may temporarily grow
beyond the defined limits when the audit daemon is stopped and the
system is under heavy audit pressure, but kauditd_thread() will
continue to make progress and drain the queues as it would for other
connection problems. For example, with the audit daemon put into a
stopped state and the system configured to audit every syscall it
was still possible to shutdown the system without a kernel panic,
deadlock, etc.; granted, the system was slow to shutdown but that is
to be expected given the extreme pressure of recording every syscall.
The timeout value of HZ/10 was chosen primarily through
experimentation and this developer's "gut feeling". There is likely
no one perfect value, but as this scenario is limited in scope (root
privileges would be needed to send SIGSTOP to the audit daemon), it
is likely not worth exposing this as a tunable at present. This can
always be done at a later date if it proves necessary.
Cc: stable@vger.kernel.org
Fixes: 5b52330bbf ("audit: fix auditd/kernel connection state tracking")
Reported-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Tested-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Reviewed-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 817fc978b5 upstream.
virtio_max_dma_size() returns the maximum DMA mapping size of the virtio
device by querying dma_max_mapping_size() for the device when the DMA
API is in use for the vring. Unfortunately, the device passed is
initialised by register_virtio_device() and does not inherit the DMA
configuration from its parent, resulting in SWIOTLB errors when bouncing
is enabled and the default 256K mapping limit (IO_TLB_SEGSIZE) is not
respected:
| virtio-pci 0000:00:01.0: swiotlb buffer is full (sz: 294912 bytes), total 1024 (slots), used 725 (slots)
Follow the pattern used elsewhere in the virtio_ring code when calling
into the DMA layer and pass the parent device to dma_max_mapping_size()
instead.
Cc: Marc Zyngier <maz@kernel.org>
Cc: Quentin Perret <qperret@google.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Signed-off-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20211201112018.25276-1-will@kernel.org
Acked-by: Jason Wang <jasowang@redhat.com>
Tested-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Fixes: e6d6dd6c87 ("virtio: Introduce virtio_max_dma_size()")
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e572ff80f0 upstream.
Make the bounds propagation in __reg_assign_32_into_64() slightly more
robust and readable by aligning it similarly as we did back in the
__reg_combine_64_into_32() counterpart. Meaning, only propagate or
pessimize them as a smin/smax pair.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3cf2b61eb0 upstream.
For the case where both s32_{min,max}_value bounds are positive, the
__reg_assign_32_into_64() directly propagates them to their 64 bit
counterparts, otherwise it pessimises them into [0,u32_max] universe and
tries to refine them later on by learning through the tnum as per comment
in mentioned function. However, that does not always happen, for example,
in mov32 operation we call zext_32_to_64(dst_reg) which invokes the
__reg_assign_32_into_64() as is without subsequent bounds update as
elsewhere thus no refinement based on tnum takes place.
Thus, not calling into the __update_reg_bounds() / __reg_deduce_bounds() /
__reg_bound_offset() triplet as we do, for example, in case of ALU ops via
adjust_scalar_min_max_vals(), will lead to more pessimistic bounds when
dumping the full register state:
Before fix:
0: (b4) w0 = -1
1: R0_w=invP4294967295
(id=0,imm=ffffffff,
smin_value=4294967295,smax_value=4294967295,
umin_value=4294967295,umax_value=4294967295,
var_off=(0xffffffff; 0x0),
s32_min_value=-1,s32_max_value=-1,
u32_min_value=-1,u32_max_value=-1)
1: (bc) w0 = w0
2: R0_w=invP4294967295
(id=0,imm=ffffffff,
smin_value=0,smax_value=4294967295,
umin_value=4294967295,umax_value=4294967295,
var_off=(0xffffffff; 0x0),
s32_min_value=-1,s32_max_value=-1,
u32_min_value=-1,u32_max_value=-1)
Technically, the smin_value=0 and smax_value=4294967295 bounds are not
incorrect, but given the register is still a constant, they break assumptions
about const scalars that smin_value == smax_value and umin_value == umax_value.
After fix:
0: (b4) w0 = -1
1: R0_w=invP4294967295
(id=0,imm=ffffffff,
smin_value=4294967295,smax_value=4294967295,
umin_value=4294967295,umax_value=4294967295,
var_off=(0xffffffff; 0x0),
s32_min_value=-1,s32_max_value=-1,
u32_min_value=-1,u32_max_value=-1)
1: (bc) w0 = w0
2: R0_w=invP4294967295
(id=0,imm=ffffffff,
smin_value=4294967295,smax_value=4294967295,
umin_value=4294967295,umax_value=4294967295,
var_off=(0xffffffff; 0x0),
s32_min_value=-1,s32_max_value=-1,
u32_min_value=-1,u32_max_value=-1)
Without the smin_value == smax_value and umin_value == umax_value invariant
being intact for const scalars, it is possible to leak out kernel pointers
from unprivileged user space if the latter is enabled. For example, when such
registers are involved in pointer arithmtics, then adjust_ptr_min_max_vals()
will taint the destination register into an unknown scalar, and the latter
can be exported and stored e.g. into a BPF map value.
Fixes: 3f50f132d8 ("bpf: Verifier, do explicit ALU32 bounds tracking")
Reported-by: Kuee K1r0a <liulin063@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1fe98f5690 upstream.
Sending them out on a different queue can cause a race condition where a
number of packets in the queue may be discarded by the receiver, because
the ADDBA request is sent too early.
This affects any driver with software A-MPDU setup which does not allocate
packet seqno in hardware on tx, regardless of whether iTXQ is used or not.
The only driver I've seen that explicitly deals with this issue internally
is mwl8k.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20211202124533.80388-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5f25e71e31 ]
This is not an unrecoverable situation. Users of kvm_read_guest_offset_cached
and kvm_write_guest_offset_cached must expect the read/write to fail, and
therefore it is possible to just return early with an error value.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 908fa88e42 ]
With the elevated 'KVM_CAP_MAX_VCPUS' value kvm_create_max_vcpus test
may hit RLIMIT_NOFILE limits:
# ./kvm_create_max_vcpus
KVM_CAP_MAX_VCPU_ID: 4096
KVM_CAP_MAX_VCPUS: 1024
Testing creating 1024 vCPUs, with IDs 0...1023.
/dev/kvm not available (errno: 24), skipping test
Adjust RLIMIT_NOFILE limits to make sure KVM_CAP_MAX_VCPUS fds can be
opened. Note, raising hard limit ('rlim_max') requires CAP_SYS_RESOURCE
capability which is generally not needed to run kvm selftests (but without
raising the limit the test is doomed to fail anyway).
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20211123135953.667434-1-vkuznets@redhat.com>
[Skip the test if the hard limit can be raised. - Paolo]
Reviewed-by: Sean Christopherson <seanjc@google.com>
Tested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 311a839a1a upstream.
Add documentation for the V4L2_CID_NOTIFY_GAINS control.
This control is required by sensors that need to know what colour
gains will be applied to pixels by downstream processing (such as by
an ISP), though the sensor does not apply these gains itself.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit a9c80593ff upstream.
We add a new control V4L2_CID_NOTIFY_GAINS which allows the sensor to
be notified what gains will be applied to the different colour
channels by subsequent processing (such as by an ISP), even though the
sensor will not apply any of these gains itself.
For Bayer sensors this will be an array control taking 4 values which
are the 4 gains arranged in the fixed order B, Gb, Gr and R,
irrespective of the exact Bayer order of the sensor itself. The use of
an array makes it straightforward to extend this control to non-Bayer
sensors (for example, sensors with an RGBW pattern) in future.
The units are in all cases linear with the default value indicating a
gain of exactly 1.0. For example, if the default value were reported as
128 then the value 192 would represent a gain of exactly 1.5.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This path actually occurs when audio is started during a hdmi mode set.
As the data will be written by vc4_hdmi_set_infoframes when packet RAM
is enabled again, don't treat as an error
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
In addition to the RGB444 output, the BCM2711 HDMI controller supports
the YUV444 and YUV422 output formats.
Let's add support for them in the driver, but still use RGB as the
preferred format.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Currently we take the max_bpc property as the bpc value and do not try
anything else.
However, what the other drivers seem to be doing is that they would try
with the highest bpc allowed by the max_bpc property and the hardware
capabilities, test if it results in an acceptable configuration, and if
not decrease the bpc and try again.
Let's use the same logic.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The current code only base its decision for whether the scrambler must be
enabled or not on the pixel clock of the mode, but doesn't take the bits
per color into account.
Let's leverage the new function to compute the clock rate in the
scrambler setup code.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
In the function that validates that the clock isn't too high, we've only
taken our controller limitations into account so far.
However, the sink can have a limit on the maximum TMDS clock it can deal
with too which is exposed through the EDID and the drm_display_info.
Make sure we check it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The code to compute our clock rate for a given setup will be called in
multiple places in the next patches, so let's create a separate function
for it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Our code is doing the same clock rate validation in multiple instances.
Let's create a helper to share the rate validation.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
In order to support the YUV output, we'll need the atomic state to know
what is the state of the associated property in the CSC setup callback.
Let's change the prototype of that callback to allow us to access it.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The current CSC setup code for the BCM2711 uses a sequence of register
writes to configure the CSC depending on whether we output using a full
or limited range.
However, with the upcoming introduction of the YUV output, we're going
to add new matrices to perform the conversions, so we should switch to
something a bit more flexible that takes the matrix as an argument and
programs the CSC accordingly.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
On BCM2711, the HDMI_CSC_CTL register value has been hardcoded to an
opaque value. Let's replace it with properly defined values.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
On the BCM2711, the HDMI_VEC_INTERFACE_XBAR register configuration
depends on whether we're using an RGB or YUV output. Let's move that
configuration to the CSC setup.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The CSC callbacks takes a boolean as an argument to tell whether we're
using the full range or limited range RGB.
However, with the upcoming YUV support, the logic will be a bit more
complex. In order to address this, let's make the callbacks take the
entire mode, and call our new helper to tell whether the full or limited
range RGB should be used.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
We're going to need to tell whether we want to run with a full or
limited range RGB output in multiple places in the code, so let's create
a helper that will return whether we need with full range or not.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The drm_hdmi_avi_infoframe_colorspace() function actually sets the
colorimetry and extended_colorimetry fields in the hdmi_avi_infoframe
structure with DRM_MODE_COLORIMETRY_* values.
To make things worse, the hdmi_avi_infoframe structure also has a
colorspace field used to signal whether an RGB or YUV output is being
used.
Let's remove the inconsistency and allow for the colorspace usage by
renaming the function.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The current code, when parsing the EDID Deep Color depths, that the
YUV422 cannot be used, referring to the HDMI 1.3 Specification.
This specification, in its section 6.2.4, indeed states:
For each supported Deep Color mode, RGB 4:4:4 shall be supported and
optionally YCBCR 4:4:4 may be supported.
YCBCR 4:2:2 is not permitted for any Deep Color mode.
This indeed can be interpreted like the code does, but the HDMI 1.4
specification further clarifies that statement in its section 6.2.4:
For each supported Deep Color mode, RGB 4:4:4 shall be supported and
optionally YCBCR 4:4:4 may be supported.
YCBCR 4:2:2 is also 36-bit mode but does not require the further use
of the Deep Color modes described in section 6.5.2 and 6.5.3.
This means that, even though YUV422 can be used with 12 bit per color,
it shouldn't be treated as a deep color mode.
This deviates from the interpretation of the code and comment, so let's
fix those.
Fixes: d0c94692e0 ("drm/edid: Parse and handle HDMI deep color modes.")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
[ Upstream commit a4d5613c4d ]
When unused memory map is freed the preserved part of the memory map is
extended to match pageblock boundaries because lots of core mm
functionality relies on homogeneity of the memory map within pageblock
boundaries.
Since pfn_valid() is used to check whether there is a valid memory map
entry for a PFN, make it return true also for PFNs that have memory map
entries even if there is no actual memory populated there.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Tested-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/lkml/20210630071211.21011-1-rppt@kernel.org/
Signed-off-by: Mark-PK Tsai <mark-pk.tsai@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f921f53e08 ]
When CONFIG_SPARSEMEM=y the ranges of the memory map that are freed are not
aligned to the pageblock boundaries which breaks assumptions about
homogeneity of the memory map throughout core mm code.
Make sure that the freed memory map is always aligned on pageblock
boundaries regardless of the memory model selection.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/lkml/20210630071211.21011-1-rppt@kernel.org/
[backport upstream modification in mm/memblock.c to arch/arm/mm/init.c]
Signed-off-by: Mark-PK Tsai <mark-pk.tsai@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e2a86800d5 ]
The code that frees unused memory map uses rounds start and end of the
holes that are freed to MAX_ORDER_NR_PAGES to preserve continuity of the
memory map for MAX_ORDER regions.
Lots of core memory management functionality relies on homogeneity of the
memory map within each pageblock which size may differ from MAX_ORDER in
certain configurations.
Although currently, for the architectures that use free_unused_memmap(),
pageblock_order and MAX_ORDER are equivalent, it is cleaner to have common
notation thought mm code.
Replace MAX_ORDER_NR_PAGES with pageblock_nr_pages and update the comments
to make it more clear why the alignment to pageblock boundaries is
required.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/lkml/20210630071211.21011-1-rppt@kernel.org/
[backport upstream modification in mm/memblock.c to arch/arm/mm/init.c]
Signed-off-by: Mark-PK Tsai <mark-pk.tsai@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c29d979260 upstream.
The space allowed for new attributes can be too small if existing header
information is large. That can happen, for example, if there are very
many CPUs, due to having an event ID per CPU per event being stored in the
header information.
Fix by adding the existing header.data_offset. Also increase the extra
space allowed to 8KiB and align to a 4KiB boundary for neatness.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lore.kernel.org/lkml/20211125071457.2066863-1-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
[Adrian: Backport to v5.10]
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dde91ccfa2 upstream.
There is a short period between a net device starts to be unregistered
and when it is actually gone. In that time frame ethtool operations
could still be performed, which might end up in unwanted or undefined
behaviours[1].
Do not allow ethtool operations after a net device starts its
unregistration. This patch targets the netlink part as the ioctl one
isn't affected: the reference to the net device is taken and the
operation is executed within an rtnl lock section and the net device
won't be found after unregister.
[1] For example adding Tx queues after unregister ends up in NULL
pointer exceptions and UaFs, such as:
BUG: KASAN: use-after-free in kobject_get+0x14/0x90
Read of size 1 at addr ffff88801961248c by task ethtool/755
CPU: 0 PID: 755 Comm: ethtool Not tainted 5.15.0-rc6+ #778
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-4.fc34 04/014
Call Trace:
dump_stack_lvl+0x57/0x72
print_address_description.constprop.0+0x1f/0x140
kasan_report.cold+0x7f/0x11b
kobject_get+0x14/0x90
kobject_add_internal+0x3d1/0x450
kobject_init_and_add+0xba/0xf0
netdev_queue_update_kobjects+0xcf/0x200
netif_set_real_num_tx_queues+0xb4/0x310
veth_set_channels+0x1c3/0x550
ethnl_set_channels+0x524/0x610
Fixes: 041b1c5d4a ("ethtool: helper functions for netlink interface")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/20211203101318.435618-1-atenart@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dbd3e6eaf3 upstream.
The removal function is called regardless of whether
/proc/i8k was created successfully or not, the later
causing a WARN() on module removal.
Fix that by only registering the removal function
if /proc/i8k was created successfully.
Tested on a Inspiron 3505.
Fixes: 039ae58503 ("hwmon: Allow to compile dell-smm-hwmon driver without /proc/i8k")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Acked-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20211112171440.59006-1-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c791fe1e2 upstream.
In writeback cache mode mtime/ctime updates are cached, and flushed to the
server using the ->write_inode() callback.
Closing the file will result in a dirty inode being immediately written,
but in other cases the inode can remain dirty after all references are
dropped. This result in the inode being written back from reclaim, which
can deadlock on a regular allocation while the request is being served.
The usual mechanisms (GFP_NOFS/PF_MEMALLOC*) don't work for FUSE, because
serving a request involves unrelated userspace process(es).
Instead do the same as for dirty pages: make sure the inode is written
before the last reference is gone.
- fallocate(2)/copy_file_range(2): these call file_update_time() or
file_modified(), so flush the inode before returning from the call
- unlink(2), link(2) and rename(2): these call fuse_update_ctime(), so
flush the ctime directly from this helper
Reported-by: chenguanyou <chenguanyou@xiaomi.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Cc: Ed Tsai <ed.tsai@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7dd5d437c2 upstream.
In 32-bit architecture, the result of sizeof() is a 32-bit integer so
the expression becomes the multiplication between 2 32-bit integer which
can potentially leads to integer overflow. As a result,
bpf_map_area_alloc() allocates less memory than needed.
Fix this by casting 1 operand to u64.
Fixes: 0d2c4f9640 ("bpf: Eliminate rlimit-based memory accounting for sockmap and sockhash maps")
Fixes: 99c51064fb ("devmap: Use bpf_map_area_alloc() for allocating hash buckets")
Fixes: 546ac1ffb7 ("bpf: add devmap, a map for storing net device references")
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210613143440.71975-1-minhquangbui99@gmail.com
Signed-off-by: Connor O'Brien <connoro@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d445aa402d upstream.
Commit 723de0f917 ("staging: most: remove device from interface
structure") moved registration of driver-provided struct device to
the most subsystem. This updated dim2 driver as well.
However, struct device passed to register_device() becomes refcounted,
and must not be explicitly deallocated, but must provide release method
instead. Which is incompatible with managing it via devres.
This patch makes the device structure allocated without devres, adds
device release method, and moves device destruction there.
Fixes: 723de0f917 ("staging: most: remove device from interface structure")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Link: https://lore.kernel.org/r/20211005143448.8660-2-nikita.yoush@cogentembedded.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3244867af8 upstream.
Do not bail early if there are no bits set in the sparse banks for a
non-sparse, a.k.a. "all CPUs", IPI request. Per the Hyper-V spec, it is
legal to have a variable length of '0', e.g. VP_SET's BankContents in
this case, if the request can be serviced without the extra info.
It is possible that for a given invocation of a hypercall that does
accept variable sized input headers that all the header input fits
entirely within the fixed size header. In such cases the variable sized
input header is zero-sized and the corresponding bits in the hypercall
input should be set to zero.
Bailing early results in KVM failing to send IPIs to all CPUs as expected
by the guest.
Fixes: 214ff83d44 ("KVM: x86: hyperv: implement PV IPI send hypercalls")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20211207220926.718794-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5ceaebcda9 ]
[WHY]
It seems like after a series of plug/unplugs we end up in a situation
where tiled display doesnt support Audio.
[HOW]
The issue seems to be related to when we check streams changed after an
HPD, we should be checking the audio_struct as well to see if any of its
values changed.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Mustapha Ghaddar <mustapha.ghaddar@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02fe0fbd8a ]
In a typical read transfer, start completion flag is being set after
read finishes (notice ipd bit 4 being set):
trasnfer poll=0
i2c start
rk3x-i2c fdd40000.i2c: IRQ: state 1, ipd: 10
i2c read
rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 1b
i2c stop
rk3x-i2c fdd40000.i2c: IRQ: state 4, ipd: 33
This causes I2C transfer being aborted in polled mode from a stop completion
handler:
trasnfer poll=1
i2c start
rk3x-i2c fdd40000.i2c: IRQ: state 1, ipd: 10
i2c read
rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 0
rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 1b
i2c stop
rk3x-i2c fdd40000.i2c: IRQ: state 4, ipd: 13
i2c stop
rk3x-i2c fdd40000.i2c: unexpected irq in STOP: 0x10
Clearing the START flag after read fixes the issue without any obvious
side effects.
This issue was dicovered on RK3566 when adding support for powering
off the RK817 PMIC.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Reviewed-by: John Keeping <john@metanate.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2191b1dfef ]
When link modes were initially added in commit 2c76267943
("net/mlx4_en: Use PTYS register to query ethtool settings") and
later updated for the new ethtool API in commit 3d8f7cc78d
("net: mlx4: use new ETHTOOL_G/SSETTINGS API") the only 1/10G non-baseT
link modes configured were 1000baseKX, 10000baseKX4 and 10000baseKR.
It looks like these got picked to represent other modes since nothing
better was available.
Switch to using more specific link modes added in commit 5711a98221
("net: ethtool: add support for 1000BaseX and missing 10G link modes").
Tested with MCX311A-XCAT connected via DAC.
Before:
% sudo ethtool enp3s0
Settings for enp3s0:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseKX/Full
10000baseKR/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: 1000baseKX/Full
10000baseKR/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 10000Mb/s
Duplex: Full
Auto-negotiation: off
Port: Direct Attach Copper
PHYAD: 0
Transceiver: internal
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000014 (20)
link ifdown
Link detected: yes
With this change:
% sudo ethtool enp3s0
Settings for enp3s0:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseX/Full
10000baseCR/Full
10000baseSR/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: 1000baseX/Full
10000baseCR/Full
10000baseSR/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 10000Mb/s
Duplex: Full
Auto-negotiation: off
Port: Direct Attach Copper
PHYAD: 0
Transceiver: internal
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000014 (20)
link ifdown
Link detected: yes
Tested-by: Michael Stapelberg <michael@stapelberg.ch>
Signed-off-by: Erik Ekman <erik@kryo.se>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e9679738a ]
Revert commit b4b844930f ("tty: serial: fsl_lpuart: drop earlycon entry
for i.MX8QXP"), because this breaks earlycon support on imx8qm/imx8qxp.
While it is true that for earlycon there is no difference between
i.MX8QXP and i.MX7ULP (for now at least), there are differences
regarding clocks and fixups for wakeup support. For that reason it was
deemed unacceptable to add the imx7ulp compatible to device tree in
order to get earlycon working again.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20211124073109.805088-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83bb2c1a01 ]
In order to be able to use primitives such as vcpu_mode_is_32bit(),
we need to synchronize the guest PSTATE. However, this is currently
done deep into the bowels of the world-switch code, and we do have
helpers evaluating this much earlier (__vgic_v3_perform_cpuif_access
and handle_aarch32_guest, for example).
Move the saving of the guest pstate into the early fixups, which
cures the first issue. The second one will be addressed separately.
Tested-by: Fuad Tabba <tabba@google.com>
Reviewed-by: Fuad Tabba <tabba@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
bcm2835_isp_remove is called on an initialisation failure, but at that
point the drvdata hasn't been set. This causes a crash when e.g. using
the cutdown firmware (gpu_mem=16).
Move platform_set_drvdata before the instance probing loop to avoid the
problem.
See: https://github.com/raspberrypi/linux/issues/4774
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
This reverts commit f814bfc5f4.
The commit caused media stalls with kodi and stateful
v4l2 video decode.
John is now using a different way of limiting latency
through stateful v4l2 so this is not required.
Change the maximum sample rate for the amplifier to
192KHz as given in the Infineon specification.
Signed-off-by: Joerg Schambacher <joerg@hifiberry.com>
Parameterise the overlays so that they can have an optional
cam0 parameter to switch to i2c_vc and csi0.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
CM4S follows CM1/3, so based on the documentation cameras/displays
connect to 0/1 and 28/29, not 0/1 and 44/45.
Likewise the camera regulator controls are independent as on CM1/3.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Not all implementations wire up the enable GPIO and may just tie
it to a supply rail.
Make it optional.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Fixing up shutdown GPIOs via overrides is ugly, and doesn't work
on eg CM4 where both cameras share the same shutdown GPIO.
The driver is now updated to use the regulator framework, so switch
to using that instead.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The driver supported using GPIOs to control the shutdown line,
but no regulator control.
Add regulator hooks.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Now that we have regulators and clocks defined in the base DT for
image sensors, switch the overlays to use them.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Unloading regulators through dynamic device tree doesn't work
as the regulators will unregister whilst clients are still
registered. Whilst the regulator framework does WARN when that
happens, the client putting the regulator then typically results
in a NULL dereference and badness.
Instead of creating regulators and clocks from the overlays,
create regulators and clocks for the sensors in the base DT.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The VL805 fetches up to 4 transfer TRBs at a time. TRB reads don't cross
a 64B boundary, and if a TRB is fetched and is not on a 64B boundary,
the read is sized up to the next 64B boundary.
However the VL805 implements a readahead prefetch for TRBs on a transfer
ring. This fetches the next 64B after any TRB read has happened. Near
the end of a ring segment, the prefetcher can read the first 64B of the
next page in physical memory and this is where the behaviour causes a
bug.
The controller does not tag reads with which endpoint they are for, so
if the start of the next page is a ring segment used by a victim
endpoint, and the victim endpoint is about to fetch TRBs from the start
of the segment, the victim endpoint will read from the prefetched data
and not perform a read to main memory. If the data is stale, the ring
cycle state bit may not be correct and the endpoint will silently halt.
Adjust trbs_per_seg for transfer rings allocated for this controller.
See https://github.com/raspberrypi/linux/issues/4685
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
In anticipation of adjusting the number of utilised TRBs in a ring
segment, add trbs_per_seg to struct xhci_ring and use this instead
of a compile-time define.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
commit 9b6164342e upstream.
This document was written a long time ago. Update it.
[1] Drop the version information
The range of the supported GCC versions are always changing. The
current minimal GCC version is 4.9, and commit 1e860048c5
("gcc-plugins: simplify GCC plugin-dev capability test") removed the
old code accordingly.
We do not need to mention specific version ranges like "all gcc versions
from 4.5 to 6.0" since we forget to update the documentation when we
raise the minimal compiler version.
[2] Drop the C compiler statements
Since commit 77342a02ff ("gcc-plugins: drop support for GCC <= 4.7")
the GCC plugin infrastructure only supports g++.
[3] Drop supported architectures
As of v5.11-rc4, the infrastructure supports more architectures;
arm, arm64, mips, powerpc, riscv, s390, um, and x86. (just grep
"select HAVE_GCC_PLUGINS") Again, we miss to update this document when a
new architecture is supported. Let's just say "only some architectures".
[4] Update the apt-get example
We are now discussing to bump the minimal version to GCC 5. The GCC 4.9
support will be removed sooner or later. Change the package example to
gcc-10-plugin-dev while we are here.
[5] Update the build target
Since commit ce2fd53a10 ("kbuild: descend into scripts/gcc-plugins/
via scripts/Makefile"), "make gcc-plugins" is not supported.
"make scripts" builds all the enabled plugins, including some other
tools.
[6] Update the steps for adding a new plugin
At first, all CONFIG options for GCC plugins were located in arch/Kconfig.
After commit 45332b1bdf ("gcc-plugins: split out Kconfig entries to
scripts/gcc-plugins/Kconfig"), scripts/gcc-plugins/Kconfig became the
central place to collect plugin CONFIG options. In my understanding,
this requirement no longer exists because commit 9f671e5815 ("security:
Create "kernel hardening" config area") moved some of plugin CONFIG
options to another file. Find an appropriate place to add the new CONFIG.
The sub-directory support was never used by anyone, and removed by
commit c17d6179ad ("gcc-plugins: remove unused GCC_PLUGIN_SUBDIR").
Remove the useless $(src)/ prefix.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f4c3b83b75 upstream.
With commit 1e860048c5 ("gcc-plugins: simplify GCC plugin-dev
capability test") applied, this hunk can be way simplified because
now scripts/gcc-plugins/Kconfig only checks plugin-version.h
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b560b21f71 upstream.
This commit adds BPF verifier selftests that cover all corner cases by
packet boundary checks. Specifically, 8-byte packet reads are tested at
the beginning of data and at the beginning of data_meta, using all kinds
of boundary checks (all comparison operators: <, >, <=, >=; both
permutations of operands: data + length compared to end, end compared to
data + length). For each case there are three tests:
1. Length is just enough for an 8-byte read. Length is either 7 or 8,
depending on the comparison.
2. Length is increased by 1 - should still pass the verifier. These
cases are useful, because they failed before commit 2fa7d94afc
("bpf: Fix the off-by-two error in range markings").
3. Length is decreased by 1 - should be rejected by the verifier.
Some existing tests are just renamed to avoid duplication.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20211207081521.41923-1-maximmi@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b383a42ca5 upstream.
INVALL CMD specifies that the ITS must ensure any caching associated with
the interrupt collection defined by ICID is consistent with the LPI
configuration tables held in memory for all Redistributors. SYNC is
required to ensure that INVALL is executed.
Currently, LPI configuration data may be inconsistent with that in the
memory within a short period of time after the INVALL command is executed.
Signed-off-by: Wudi Wang <wangwudi@hisilicon.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Fixes: cc2d3216f5 ("irqchip: GICv3: ITS command queue")
Link: https://lore.kernel.org/r/20211208015429.5007-1-zhangshaokun@hisilicon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0a553502e upstream.
irq-armada-370-xp driver already sets MSI_FLAG_MULTI_PCI_MSI flag into
msi_domain_info structure. But allocated interrupt numbers for Multi-MSI
needs to be properly aligned otherwise devices send MSI interrupt with
wrong number.
Fix this issue by using function bitmap_find_free_region() instead of
bitmap_find_next_zero_area() to allocate aligned interrupt numbers.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: a71b9412c9 ("irqchip/armada-370-xp: Allow allocation of multiple MSIs")
Cc: stable@vger.kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211125130057.26705-2-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6661146427 upstream.
IIO trigger handlers must call iio_trigger_notify_done() when done. This
must be done even when an error occurred. Otherwise the trigger will be
seen as busy indefinitely and the trigger handler will never be called
again.
The ad7768-1 driver neglects to call iio_trigger_notify_done() when there
is an error reading the converter data. Fix this by making sure that
iio_trigger_notify_done() is included in the error exit path.
Fixes: a5f8c7da3d ("iio: adc: Add AD7768-1 ADC basic support")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211101144055.13858-2-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92beafb76a upstream.
Both the charging and discharging currents on AXP22x are stored as
12-bit integers, in accordance with the datasheet.
It's also confirmed by vendor BSP (axp20x_adc.c:axp22_icharge_to_mA).
The scale factor of 0.5 is never mentioned in datasheet, nor in the
vendor source code. I think it was here to compensate for
erroneous addition bit in register width.
Tested on custom A40i+AXP221s board with external ammeter as
a reference.
Fixes: 0e34d5de96 ("iio: adc: add support for X-Powers AXP20X and AXP22X PMICs ADCs")
Signed-off-by: Evgeny Boger <boger@wirenboard.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20211116213746.264378-1-boger@wirenboard.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f711f28e71 upstream.
Some I/Os are connected to ADC input channels, when the corresponding bit
in PCSEL register are set on STM32H7 and STM32MP15. This is done in the
prepare routine of stm32-adc driver.
There are constraints here, as PCSEL shouldn't be set when VDDA supply
is disabled. Enabling/disabling of VDDA supply in done via stm32-adc-core
runtime PM routines (before/after ADC is enabled/disabled).
Currently, PCSEL remains set when disabling ADC. Later on, PM runtime
can disable the VDDA supply. This creates some conditions on I/Os that
can start to leak current.
So PCSEL needs to be cleared when disabling the ADC.
Fixes: 95e339b6e8 ("iio: adc: stm32: add support for STM32H7")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Reviewed-by: Olivier Moysan <olivier.moysan@foss.st.com>
Link: https://lore.kernel.org/r/1634905169-23762-1-git-send-email-fabrice.gasnier@foss.st.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67fe29583e upstream.
IIO trigger handlers must call iio_trigger_notify_done() when done. This
must be done even when an error occurred. Otherwise the trigger will be
seen as busy indefinitely and the trigger handler will never be called
again.
The itg3200 driver neglects to call iio_trigger_notify_done() when there is
an error reading the gyro data. Fix this by making sure that
iio_trigger_notify_done() is included in the error exit path.
Fixes: 9dbf091da0 ("iio: gyro: Add itg3200")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211101144055.13858-1-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45febe0d63 upstream.
IIO trigger handlers need to return one of the irqreturn_t values.
Returning an error code is not supported.
The kxsd9 interrupt handler returns an error code if reading the data
registers fails. In addition when exiting due to an error the trigger
handler does not call `iio_trigger_notify_done()`. Which when not done
keeps the triggered disabled forever.
Modify the code so that the function returns a valid irqreturn_t value as
well as calling `iio_trigger_notify_done()` on all exit paths.
Since we can't return the error code make sure to at least log it as part
of the error message.
Fixes: 0427a106a9 ("iio: accel: kxsd9: Add triggered buffer handling")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20211024171251.22896-2-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef9d67fa72 upstream.
IIO trigger handlers need to return one of the irqreturn_t values.
Returning an error code is not supported.
The ltr501 interrupt handler gets this right for most error paths, but
there is one case where it returns the error code.
In addition for this particular case the trigger handler does not call
`iio_trigger_notify_done()`. Which when not done keeps the triggered
disabled forever.
Modify the code so that the function returns a valid irqreturn_t value as
well as calling `iio_trigger_notify_done()` on all exit paths.
Fixes: 2690be9051 ("iio: Add Lite-On ltr501 ambient light / proximity sensor driver")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211024171251.22896-1-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd00822357 upstream.
The mma8452 driver directly assigns a trigger to the struct iio_dev. The
IIO core when done using this trigger will call `iio_trigger_put()` to drop
the reference count by 1.
Without the matching `iio_trigger_get()` in the driver the reference count
can reach 0 too early, the trigger gets freed while still in use and a
use-after-free occurs.
Fix this by getting a reference to the trigger before assigning it to the
IIO device.
Fixes: ae6d9ce056 ("iio: mma8452: Add support for interrupt driven triggers.")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211024092700.6844-1-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a827a49846 upstream.
In viio_trigger_alloc() device_initialize() is used to set the initial
reference count of the trigger to 1. Then another get_device() is called on
trigger. This sets the reference count to 2 before the trigger is returned.
iio_trigger_free(), which is the matching API to viio_trigger_alloc(),
calls put_device() which decreases the reference count by 1. But the second
reference count acquired in viio_trigger_alloc() is never dropped.
As a result the iio_trigger_release() function is never called and the
memory associated with the trigger is never freed.
Since there is no reason for the trigger to start its lifetime with two
reference counts just remove the extra get_device() in
viio_trigger_alloc().
Fixes: 5f9c035cae ("staging:iio:triggers. Add a reference get to the core for triggers.")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20211024092700.6844-2-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7faac1953e upstream.
Make xhci_disable_slot() synchronous, thus ensuring it, and
xhci_free_dev() calling it return after xHC controller completes
the disable slot command.
Otherwise the roothub and xHC host may runtime suspend, and clear the
command ring while the disable slot command is being processed.
This causes a command completion mismatch as the completion event can't
be mapped to the correct command.
Command ring gets out of sync and commands time out.
Driver finally assumes host is unresponsive and bails out.
usb 2-4: USB disconnect, device number 10
xhci_hcd 0000:00:0d.0: ERROR mismatched command completion event
...
xhci_hcd 0000:00:0d.0: xHCI host controller not responding, assume dead
xhci_hcd 0000:00:0d.0: HC died; cleaning up
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211210141735.1384209-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 811ae81320 upstream.
When the xHCI is quirked with XHCI_RESET_ON_RESUME, runtime resume
routine also resets the controller.
This is bad for USB drivers without reset_resume callback, because
there's no subsequent call of usb_dev_complete() ->
usb_resume_complete() to force rebinding the driver to the device. For
instance, btusb device stops working after xHCI controller is runtime
resumed, if the controlled is quirked with XHCI_RESET_ON_RESUME.
So always take XHCI_RESET_ON_RESUME into account to solve the issue.
Cc: <stable@vger.kernel.org>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211210141735.1384209-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 86ebbc11bb upstream.
Under some conditions, USB gadget devices can show allocated buffer
contents to a host. Fix this up by zero-allocating them so that any
extra data will all just be zeros.
Reported-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Tested-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 153a2d7e33 upstream.
Sometimes USB hosts can ask for buffers that are too large from endpoint
0, which should not be allowed. If this happens for OUT requests, stall
the endpoint, but for IN requests, trim the request size to the endpoint
buffer size.
Co-developed-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f6071e5e39 upstream.
Currently rp_filter tests in fib_tests.sh:fib_rp_filter_test() are
failing. ping sockets are bound to dummy1 using the "-I" option
(SO_BINDTODEVICE), but socket lookup is failing when receiving ping
replies, since the routing table thinks they belong to dummy0.
For example, suppose ping is using a SOCK_RAW socket for ICMP messages.
When receiving ping replies, in __raw_v4_lookup(), sk->sk_bound_dev_if
is 3 (dummy1), but dif (skb_rtable(skb)->rt_iif) says 2 (dummy0), so the
raw_sk_bound_dev_eq() check fails. Similar things happen in
ping_lookup() for SOCK_DGRAM sockets.
These tests used to pass due to a bug [1] in iputils, where "ping -I"
actually did not bind ICMP message sockets to device. The bug has been
fixed by iputils commit f455fee41c07 ("ping: also bind the ICMP socket
to the specific device") in 2016, which is why our rp_filter tests
started to fail. See [2] .
Fixing the tests while keeping everything in one netns turns out to be
nontrivial. Rework the tests and build the following topology:
┌─────────────────────────────┐ ┌─────────────────────────────┐
│ network namespace 1 (ns1) │ │ network namespace 2 (ns2) │
│ │ │ │
│ ┌────┐ ┌─────┐ │ │ ┌─────┐ ┌────┐ │
│ │ lo │<───>│veth1│<────────┼────┼─>│veth2│<──────────>│ lo │ │
│ └────┘ ├─────┴──────┐ │ │ ├─────┴──────┐ └────┘ │
│ │192.0.2.1/24│ │ │ │192.0.2.1/24│ │
│ └────────────┘ │ │ └────────────┘ │
└─────────────────────────────┘ └─────────────────────────────┘
Consider sending an ICMP_ECHO packet A in ns2. Both source and
destination IP addresses are 192.0.2.1, and we use strict mode rp_filter
in both ns1 and ns2:
1. A is routed to lo since its destination IP address is one of ns2's
local addresses (veth2);
2. A is redirected from lo's egress to veth2's egress using mirred;
3. A arrives at veth1's ingress in ns1;
4. A is redirected from veth1's ingress to lo's ingress, again, using
mirred;
5. In __fib_validate_source(), fib_info_nh_uses_dev() returns false,
since A was received on lo, but reverse path lookup says veth1;
6. However A is not dropped since we have relaxed this check for lo in
commit 66f8209547 ("fib: relax source validation check for loopback
packets");
Making sure A is not dropped here in this corner case is the whole point
of having this test.
7. As A reaches the ICMP layer, an ICMP_ECHOREPLY packet, B, is
generated;
8. Similarly, B is redirected from lo's egress to veth1's egress (in
ns1), then redirected once again from veth2's ingress to lo's
ingress (in ns2), using mirred.
Also test "ping 127.0.0.1" from ns2. It does not trigger the relaxed
check in __fib_validate_source(), but just to make sure the topology
works with loopback addresses.
Tested with ping from iputils 20210722-41-gf9fb573:
$ ./fib_tests.sh -t rp_filter
IPv4 rp_filter tests
TEST: rp_filter passes local packets [ OK ]
TEST: rp_filter passes loopback packets [ OK ]
[1] https://github.com/iputils/iputils/issues/55
[2] f455fee41c
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Fixes: adb701d6cf ("selftests: add a test case for rp_filter")
Reviewed-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Peilin Ye <peilin.ye@bytedance.com>
Acked-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20211201004720.6357-1-yepeilin.cs@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d17b9737c2 upstream.
The ql_wait_for_drvr_lock() fails and returns false, then this
function should return an error code instead of returning success.
The other problem is that the success path prints an error message
netdev_err(ndev, "Releasing driver lock\n"); Delete that and
re-order the code a little to make it more clear.
Fixes: 5a4faa8737 ("[PATCH] qla3xxx NIC driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211207082416.GA16110@kili
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5bd95d171 upstream.
Background:
We have a customer is running a Profinet stack on the 8MM which receives and
responds PNIO packets every 4ms and PNIO-CM packets every 40ms. However, from
time to time the received PNIO-CM package is "stock" and is only handled when
receiving a new PNIO-CM or DCERPC-Ping packet (tcpdump shows the PNIO-CM and
the DCERPC-Ping packet at the same time but the PNIO-CM HW timestamp is from
the expected 40 ms and not the 2s delay of the DCERPC-Ping).
After debugging, we noticed PNIO, PNIO-CM and DCERPC-Ping packets would
be handled by different RX queues.
The root cause should be driver ack all queues' interrupt when handle a
specific queue in fec_enet_rx_queue(). The blamed patch is introduced to
receive as much packets as possible once to avoid interrupt flooding.
But it's unreasonable to clear other queues'interrupt when handling one
queue, this patch tries to fix it.
Fixes: ed63f1dcd5 (net: fec: clear receive interrupts before processing a packet)
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Reported-by: Nicolas Diaz <nicolas.diaz@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20211206135457.15946-1-qiangqing.zhang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit badd7857f5 upstream.
There are two error paths which accidentally return success instead of
a negative error code.
Fixes: bbd2190ce9 ("Altera TSE: Add main and header file for Altera Ethernet Driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2be6d4d16a upstream.
Currently, due to the sequential use of min_t() and clamp_t() macros,
in cdc_ncm_check_tx_max(), if dwNtbOutMaxSize is not set, the logic
sets tx_max to 0. This is then used to allocate the data area of the
SKB requested later in cdc_ncm_fill_tx_frame().
This does not cause an issue presently because when memory is
allocated during initialisation phase of SKB creation, more memory
(512b) is allocated than is required for the SKB headers alone (320b),
leaving some space (512b - 320b = 192b) for CDC data (172b).
However, if more elements (for example 3 x u64 = [24b]) were added to
one of the SKB header structs, say 'struct skb_shared_info',
increasing its original size (320b [320b aligned]) to something larger
(344b [384b aligned]), then suddenly the CDC data (172b) no longer
fits in the spare SKB data area (512b - 384b = 128b).
Consequently the SKB bounds checking semantics fails and panics:
skbuff: skb_over_panic: text:ffffffff830a5b5f len:184 put:172 \
head:ffff888119227c00 data:ffff888119227c00 tail:0xb8 end:0x80 dev:<NULL>
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:110!
RIP: 0010:skb_panic+0x14f/0x160 net/core/skbuff.c:106
<snip>
Call Trace:
<IRQ>
skb_over_panic+0x2c/0x30 net/core/skbuff.c:115
skb_put+0x205/0x210 net/core/skbuff.c:1877
skb_put_zero include/linux/skbuff.h:2270 [inline]
cdc_ncm_ndp16 drivers/net/usb/cdc_ncm.c:1116 [inline]
cdc_ncm_fill_tx_frame+0x127f/0x3d50 drivers/net/usb/cdc_ncm.c:1293
cdc_ncm_tx_fixup+0x98/0xf0 drivers/net/usb/cdc_ncm.c:1514
By overriding the max value with the default CDC_NCM_NTB_MAX_SIZE_TX
when not offered through the system provided params, we ensure enough
data space is allocated to handle the CDC data, meaning no crash will
occur.
Cc: Oliver Neukum <oliver@neukum.org>
Fixes: 289507d336 ("net: cdc_ncm: use sysfs for rx/tx aggregation tuning")
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Link: https://lore.kernel.org/r/20211202143437.1411410-1-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d1d57debe upstream.
Since 66dfdff03d ("perf tools: Add Python 3 support") we don't use
the tools/build/feature/test-libpython-version.c version in any Makefile
feature check:
$ find tools/ -type f | xargs grep feature-libpython-version
$
The only place where this was used was removed in 66dfdff03d:
- ifneq ($(feature-libpython-version), 1)
- $(warning Python 3 is not yet supported; please set)
- $(warning PYTHON and/or PYTHON_CONFIG appropriately.)
- $(warning If you also have Python 2 installed, then)
- $(warning try something like:)
- $(warning $(and ,))
- $(warning $(and ,) make PYTHON=python2)
- $(warning $(and ,))
- $(warning Otherwise, disable Python support entirely:)
- $(warning $(and ,))
- $(warning $(and ,) make NO_LIBPYTHON=1)
- $(warning $(and ,))
- $(error $(and ,))
- else
- LDFLAGS += $(PYTHON_EMBED_LDFLAGS)
- EXTLIBS += $(PYTHON_EMBED_LIBADD)
- LANG_BINDINGS += $(obj-perf)python/perf.so
- $(call detected,CONFIG_LIBPYTHON)
- endif
And nowadays we either build with PYTHON=python3 or just install the
python3 devel packages and perf will build against it.
But the leftover feature-libpython-version check made the fast path
feature detection to break in all cases except when python2 devel files
were installed:
$ rpm -qa | grep python.*devel
python3-devel-3.9.7-1.fc34.x86_64
$ rm -rf /tmp/build/perf ; mkdir -p /tmp/build/perf ;
$ make -C tools/perf O=/tmp/build/perf install-bin
make: Entering directory '/var/home/acme/git/perf/tools/perf'
BUILD: Doing 'make -j32' parallel build
HOSTCC /tmp/build/perf/fixdep.o
<SNIP>
$ cat /tmp/build/perf/feature/test-all.make.output
In file included from test-all.c:18:
test-libpython-version.c:5:10: error: #error
5 | #error
| ^~~~~
$ ldd ~/bin/perf | grep python
libpython3.9.so.1.0 => /lib64/libpython3.9.so.1.0 (0x00007fda6dbcf000)
$
As python3 is the norm these days, fix this by just removing the unused
feature-libpython-version feature check, making the test-all fast path
to work with the common case.
With this:
$ rm -rf /tmp/build/perf ; mkdir -p /tmp/build/perf ;
$ make -C tools/perf O=/tmp/build/perf install-bin |& head
make: Entering directory '/var/home/acme/git/perf/tools/perf'
BUILD: Doing 'make -j32' parallel build
HOSTCC /tmp/build/perf/fixdep.o
HOSTLD /tmp/build/perf/fixdep-in.o
LINK /tmp/build/perf/fixdep
Auto-detecting system features:
... dwarf: [ on ]
... dwarf_getlocations: [ on ]
... glibc: [ on ]
$ ldd ~/bin/perf | grep python
libpython3.9.so.1.0 => /lib64/libpython3.9.so.1.0 (0x00007f58800b0000)
$ cat /tmp/build/perf/feature/test-all.make.output
$
Reviewed-by: James Clark <james.clark@arm.com>
Fixes: 66dfdff03d ("perf tools: Add Python 3 support")
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jaroslav Škarvada <jskarvad@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: https://lore.kernel.org/lkml/YaYmeeC6CS2b8OSz@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 96db48c9d7 upstream.
This binding was already documented in phy.txt, commit 252ae5330d
("Documentation: devicetree: Add PHY no lane swap binding"), but got
accidently removed during YAML conversion in commit d8704342c1
("dt-bindings: net: Add a YAML schemas for the generic PHY options").
Note: 'enet-phy-lane-no-swap' and the absence of 'enet-phy-lane-swap' are
not identical, as the former one disable this feature, while the latter
one doesn't change anything.
Fixes: d8704342c1 ("dt-bindings: net: Add a YAML schemas for the generic PHY options")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20211130082756.713919-1-alexander.stein@ew.tq-group.com
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6a631c0432 upstream.
The initial implementation of migrate_disable() for mainline was a
wrapper around preempt_disable(). RT kernels substituted this with
a real migrate disable implementation.
Later on mainline gained true migrate disable support, but the
documentation was not updated.
Update the documentation, remove the claims about migrate_disable()
mapping to preempt_disable() on non-PREEMPT_RT kernels.
Fixes: 74d862b682 ("sched: Make migrate_disable/enable() independent of RT")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20211127163200.10466-2-bigeasy@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39bd54d43b upstream.
This reverts commit 239edf686c.
239edf686c ("PCI: aardvark: Fix support for PCI_ROM_ADDRESS1 on emulated
bridge") added support for the Type 1 Expansion ROM BAR at config offset
0x38, based on the register being listed in the Marvell Armada A3720 spec.
But the spec doesn't document it at all for RC mode, and there is no ROM in
the SOC, so remove this emulation for now.
The PCI bridge which represents aardvark's PCIe Root Port has an Expansion
ROM Base Address register at offset 0x30, but its meaning is different than
PCI's Expansion ROM BAR register, although the layout is the same. (This
is why we thought it does the same thing.)
First: there is no ROM (or part of BootROM) in the A3720 SOC dedicated for
PCIe Root Port (or controller in RC mode) containing executable code that
would initialize the Root Port, suitable for execution in bootloader (this
is how Expansion ROM BAR is used on x86).
Second: in A3720 spec the register (address 0xD0070030) is not documented
at all for Root Complex mode, but similar to other BAR registers, it has an
"entangled partner" in register 0xD0075920, which does address translation
for the BAR in 0xD0070030:
- the BAR register sets the address from the view of PCIe bus
- the translation register sets the address from the view of the CPU
The other BAR registers also have this entangled partner, and they can be
used to:
- in RC mode: address-checking on the receive side of the RC (they can
define address ranges for memory accesses from remote Endpoints to the
RC)
- in Endpoint mode: allow the remote CPU to access memory on A3720
The Expansion ROM BAR has only the Endpoint part documented, but from the
similarities we think that it can also be used in RC mode in that way.
So either Expansion ROM BAR has different meaning (if the hypothesis above
is true), or we don't know it's meaning (since it is not documented for RC
mode).
Remove the register from the emulated bridge accessing functions.
[bhelgaas: summarize reason for removal (first paragraph)]
Fixes: 239edf686c ("PCI: aardvark: Fix support for PCI_ROM_ADDRESS1 on emulated bridge")
Link: https://lore.kernel.org/r/20211125160148.26029-3-kabel@kernel.org
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9472335eaa upstream.
Under certain circumstances, the timing settings calculated by
the FSMC NAND controller driver were inaccurate.
These settings led to incorrect data reads or fallback to
timing mode 0 depending on the NAND chip used.
The timing computation did not take into account the following
constraint given in SPEAr3xx reference manual:
twait >= tCEA - (tset * TCLK) + TOUTDEL + TINDEL
Enhance the timings calculation by taking into account this
additional constraint.
This change has no impact on slow timing modes such as mode 0.
Indeed, on mode 0, computed values are the same with and
without the patch.
NANDs which previously stayed in mode 0 because of fallback to
mode 0 can now work at higher speeds and NANDs which were not
working at all because of the corrupted data work at high
speeds without troubles.
Overall improvement on a Micron/MT29F1G08 (flash_speed tool):
mode0 mode3
eraseblock write speed 3220 KiB/s 4511 KiB/s
eraseblock read speed 4491 KiB/s 7529 KiB/s
Fixes: d9fb079571 ("mtd: nand: fsmc: add support for SDR timings")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211119150316.43080-5-herve.codina@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8aa55ab422 upstream.
After setting pre-set combined to 16 queues and reserving 16 queues by
tc qdisc, pre-set maximum combined queues returned to default value
after VF reset being 4 and this generated errors during removing tc.
Fixed by removing clear num_req_queues before reset VF.
Fixes: e284fc2804 (i40e: Add and delete cloud filter)
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Bindushree P <Bindushree.p@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61125b8be8 upstream.
Fix failed operation code appearing if handling messages from VF.
Implemented by waiting for VF appropriate state if request starts
handle while VF reset.
Without this patch the message handling request while VF is in
a reset state ends with error -5 (I40E_ERR_PARAM).
Fixes: 5c3c48ac6b ("i40e: implement virtual device interface")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b0969f8389 upstream.
When hns_roce_v2_destroy_qp() is called, the brief calling process of the
driver is as follows:
......
hns_roce_v2_destroy_qp
hns_roce_v2_qp_modify
hns_roce_cmd_mbox
hns_roce_qp_destroy
If hns_roce_cmd_mbox() detects that the hardware is being reset during the
execution of the hns_roce_cmd_mbox(), the driver will not be able to get
the return value from the hardware (the firmware cannot respond to the
driver's mailbox during the hardware reset phase).
The driver needs to wait for the hardware reset to complete before
continuing to execute hns_roce_qp_destroy(), otherwise it may happen that
the driver releases the resources but the hardware is still accessing. In
order to fix this problem, HNS RoCE needs to add a piece of code to wait
for the hardware reset to complete.
The original interface get_hw_reset_stat() is the instantaneous state of
the hardware reset, which cannot accurately reflect whether the hardware
reset is completed, so it needs to be replaced with the ae_dev_reset_cnt
interface.
The sign that the hardware reset is complete is that the return value of
the ae_dev_reset_cnt interface is greater than the original value
reset_cnt recorded by the driver.
Fixes: 6a04aed6af ("RDMA/hns: Fix the chip hanging caused by sending mailbox&CMQ during reset")
Link: https://lore.kernel.org/r/20211123142402.26936-1-liangwenpeng@huawei.com
Signed-off-by: Yangyang Li <liyangyang20@huawei.com>
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52414e27d6 upstream.
is_reset is used to indicate whether the hardware starts to reset. When
hns_roce_hw_v2_reset_notify_down() is called, the hardware has not yet
started to reset. If is_reset is set at this time, all mailbox operations
of resource destroy actions will be intercepted by driver. When the driver
cleans up resources, but the hardware is still accessed, the following
errors will appear:
arm-smmu-v3 arm-smmu-v3.2.auto: event 0x10 received:
arm-smmu-v3 arm-smmu-v3.2.auto: 0x0000350100000010
arm-smmu-v3 arm-smmu-v3.2.auto: 0x000002088000003f
arm-smmu-v3 arm-smmu-v3.2.auto: 0x00000000a50e0800
arm-smmu-v3 arm-smmu-v3.2.auto: 0x0000000000000000
arm-smmu-v3 arm-smmu-v3.2.auto: event 0x10 received:
arm-smmu-v3 arm-smmu-v3.2.auto: 0x0000350100000010
arm-smmu-v3 arm-smmu-v3.2.auto: 0x000002088000043e
arm-smmu-v3 arm-smmu-v3.2.auto: 0x00000000a50a0800
arm-smmu-v3 arm-smmu-v3.2.auto: 0x0000000000000000
arm-smmu-v3 arm-smmu-v3.2.auto: event 0x10 received:
arm-smmu-v3 arm-smmu-v3.2.auto: 0x0000350100000010
arm-smmu-v3 arm-smmu-v3.2.auto: 0x0000020880000436
arm-smmu-v3 arm-smmu-v3.2.auto: 0x00000000a50a0880
arm-smmu-v3 arm-smmu-v3.2.auto: 0x0000000000000000
arm-smmu-v3 arm-smmu-v3.2.auto: event 0x10 received:
arm-smmu-v3 arm-smmu-v3.2.auto: 0x0000350100000010
arm-smmu-v3 arm-smmu-v3.2.auto: 0x000002088000043a
arm-smmu-v3 arm-smmu-v3.2.auto: 0x00000000a50e0840
hns3 0000:35:00.0: INT status: CMDQ(0x0) HW errors(0x0) other(0x0)
arm-smmu-v3 arm-smmu-v3.2.auto: 0x0000000000000000
hns3 0000:35:00.0: received unknown or unhandled event of vector0
arm-smmu-v3 arm-smmu-v3.2.auto: event 0x10 received:
arm-smmu-v3 arm-smmu-v3.2.auto: 0x0000350100000010
{34}[Hardware Error]: Hardware error from APEI Generic Hardware Error Source: 7
is_reset will be set correctly in check_aedev_reset_status(), so the
setting in hns_roce_hw_v2_reset_notify_down() should be deleted.
Fixes: 726be12f5c ("RDMA/hns: Set reset flag when hw resetting")
Link: https://lore.kernel.org/r/20211123084809.37318-1-liangwenpeng@huawei.com
Signed-off-by: Yangyang Li <liyangyang20@huawei.com>
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23ba28616d upstream.
Currently each channel is added as list to dai channel list, however
there is danger of adding same channel to multiple dai channel list
which endups corrupting the other list where its already added.
This patch ensures that the channel is actually free before adding to
the dai channel list and also ensures that the channel is on the list
before deleting it.
This check was missing previously, and we did not hit this issue as
we were testing very simple usecases with sequence of amixer commands.
Fixes: a70d924575 ("ASoC: wcd934x: add capture dapm widgets")
Fixes: dd9eb19b56 ("ASoC: wcd934x: add playback dapm widgets")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20211130160507.22180-2-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4739d88ad8 upstream.
msm_routing_put_audio_mixer() can return incorrect value in various scenarios.
scenario 1:
amixer cset iface=MIXER,name='SLIMBUS_0_RX Audio Mixer MultiMedia1' 1
amixer cset iface=MIXER,name='SLIMBUS_0_RX Audio Mixer MultiMedia1' 0
return value is 0 instead of 1 eventhough value was changed
scenario 2:
amixer cset iface=MIXER,name='SLIMBUS_0_RX Audio Mixer MultiMedia1' 1
amixer cset iface=MIXER,name='SLIMBUS_0_RX Audio Mixer MultiMedia1' 1
return value is 1 instead of 0 eventhough the value was not changed
scenario 3:
amixer cset iface=MIXER,name='SLIMBUS_0_RX Audio Mixer MultiMedia1' 0
return value is 1 instead of 0 eventhough the value was not changed
Fix this by adding checks, so that change notifications are sent correctly.
Fixes: e3a33673e8 ("ASoC: qdsp6: q6routing: Add q6routing driver")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20211130163110.5628-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 444dd878e8 upstream.
The kerneldoc comment of pm_runtime_active() does not reflect the
behavior of the function, so update it accordingly.
Fixes: 403d2d116e ("PM: runtime: Add kerneldoc comments to multiple helpers")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e227b198a upstream.
Although it is unlikely that stack could transmit a non LSO
skb with length > MTU, however in some cases or environment such
occurrences actually resulted into firmware asserts due to packet
length being greater than the max supported by the device (~9700B).
This patch adds the safeguard for such odd cases to avoid firmware
asserts.
v2: Added "Fixes" tag with one of the initial driver commit
which enabled the TX traffic actually (as this was probably
day1 issue which was discovered recently by some customer
environment)
Fixes: a2ec6172d2 ("qede: Add support for link")
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Link: https://lore.kernel.org/r/20211203174413.13090-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7db0e0c819 upstream.
According to ZBC and SPC specifications, the unit of ALLOCATION LENGTH
field of REPORT ZONES command is byte. However, current scsi_debug
implementation handles it as number of zones to calculate buffer size to
report zones. When the ALLOCATION LENGTH has a large number, this results
in too large buffer size and causes memory allocation failure. Fix the
failure by handling ALLOCATION LENGTH as byte unit.
Link: https://lore.kernel.org/r/20211207010638.124280-1-shinichiro.kawasaki@wdc.com
Fixes: f0d1cf9378 ("scsi: scsi_debug: Add ZBC zone commands")
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6539262057 upstream.
Calling scsi_remove_host() before scsi_add_host() results in a crash:
BUG: kernel NULL pointer dereference, address: 0000000000000108
RIP: 0010:device_del+0x63/0x440
Call Trace:
device_unregister+0x17/0x60
scsi_remove_host+0xee/0x2a0
pm8001_pci_probe+0x6ef/0x1b90 [pm80xx]
local_pci_probe+0x3f/0x90
We cannot call scsi_remove_host() in pm8001_alloc() because scsi_add_host()
has not been called yet at that point in time.
Function call tree:
pm8001_pci_probe()
|
`- pm8001_pci_alloc()
| |
| `- pm8001_alloc()
| |
| `- scsi_remove_host()
|
`- scsi_add_host()
Link: https://lore.kernel.org/r/20211201041627.1592487-1-ipylypiv@google.com
Fixes: 05c6c029a4 ("scsi: pm80xx: Increase number of supported queues")
Reviewed-by: Vishakha Channapattan <vishakhavc@google.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 48b27b6b51 upstream.
As people have been asking to allow non-root processes to have access to
the tracefs directory, it was considered best to only allow groups to have
access to the directory, where it is easier to just set the tracefs file
system to a specific group (as other would be too dangerous), and that way
the admins could pick which processes would have access to tracefs.
Unfortunately, this broke tooling on Android that expected the other bit
to be set. For some special cases, for non-root tools to trace the system,
tracefs would be mounted and change the permissions of the top level
directory which gave access to all running tasks permission to the
tracing directory. Even though this would be dangerous to do in a
production environment, for testing environments this can be useful.
Now with the new changes to not allow other (which is still the proper
thing to do), it breaks the testing tooling. Now more code needs to be
loaded on the system to change ownership of the tracing directory.
The real solution is to have tracefs honor the gid=xxx option when
mounting. That is,
(tracing group tracing has value 1003)
mount -t tracefs -o gid=1003 tracefs /sys/kernel/tracing
should have it that all files in the tracing directory should be of the
given group.
Copy the logic from d_walk() from dcache.c and simplify it for the mount
case of tracefs if gid is set. All the files in tracefs will be walked and
their group will be set to the value passed in.
Link: https://lkml.kernel.org/r/20211207171729.2a54e1b3@gandalf.local.home
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-fsdevel@vger.kernel.org
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reported-by: Kalesh Singh <kaleshsingh@google.com>
Reported-by: Yabin Cui <yabinc@google.com>
Fixes: 49d67e4457 ("tracefs: Have tracefs directories not set OTH permission bits by default")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a50e659b2a upstream.
The registration of XDP queue information is incorrect because the
RX queue id we use is invalid. When port->id == 0 it appears to works
as expected yet it's no longer the case when port->id != 0.
The problem arised while using a recent kernel version on the
MACCHIATOBin. This board has several ports:
* eth0 and eth1 are 10Gbps interfaces ; both ports has port->id == 0;
* eth2 is a 1Gbps interface with port->id != 0.
Code from xdp-tutorial (more specifically advanced03-AF_XDP) was used
to test packet capture and injection on all these interfaces. The XDP
kernel was simplified to:
SEC("xdp_sock")
int xdp_sock_prog(struct xdp_md *ctx)
{
int index = ctx->rx_queue_index;
/* A set entry here means that the correspnding queue_id
* has an active AF_XDP socket bound to it. */
if (bpf_map_lookup_elem(&xsks_map, &index))
return bpf_redirect_map(&xsks_map, index, 0);
return XDP_PASS;
}
Starting the program using:
./af_xdp_user -d DEV
Gives the following result:
* eth0 : ok
* eth1 : ok
* eth2 : no capture, no injection
Investigating the issue shows that XDP rx queues for eth2 are wrong:
XDP expects their id to be in the range [0..3] but we found them to be
in the range [32..35].
Trying to force rx queue ids using:
./af_xdp_user -d eth2 -Q 32
fails as expected (we shall not have more than 4 queues).
When we register the XDP rx queue information (using
xdp_rxq_info_reg() in function mvpp2_rxq_init()) we tell it to use
rxq->id as the queue id. This value is computed as:
rxq->id = port->id * max_rxq_count + queue_id
where max_rxq_count depends on the device version. In the MACCHIATOBin
case, this value is 32, meaning that rx queues on eth2 are numbered
from 32 to 35 - there are four of them.
Clearly, this is not the per-port queue id that XDP is expecting:
it wants a value in the range [0..3]. It shall directly use queue_id
which is stored in rxq->logic_rxq -- so let's use that value instead.
rxq->id is left untouched ; its value is indeed valid but it should
not be used in this context.
This is consistent with the remaining part of the code in
mvpp2_rxq_init().
With this change, packet capture is working as expected on all the
MACCHIATOBin ports.
Fixes: b27db2274b ("mvpp2: use page_pool allocator")
Signed-off-by: Louis Amas <louis.amas@eho.link>
Signed-off-by: Emmanuel Deloget <emmanuel.deloget@eho.link>
Reviewed-by: Marcin Wojtas <mw@semihalf.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/r/20211207143423.916334-1-louis.amas@eho.link
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 50252e4b5e upstream.
signalfd_poll() and binder_poll() are special in that they use a
waitqueue whose lifetime is the current task, rather than the struct
file as is normally the case. This is okay for blocking polls, since a
blocking poll occurs within one task; however, non-blocking polls
require another solution. This solution is for the queue to be cleared
before it is freed, by sending a POLLFREE notification to all waiters.
Unfortunately, only eventpoll handles POLLFREE. A second type of
non-blocking poll, aio poll, was added in kernel v4.18, and it doesn't
handle POLLFREE. This allows a use-after-free to occur if a signalfd or
binder fd is polled with aio poll, and the waitqueue gets freed.
Fix this by making aio poll handle POLLFREE.
A patch by Ramji Jiyani <ramjiyani@google.com>
(https://lore.kernel.org/r/20211027011834.2497484-1-ramjiyani@google.com)
tried to do this by making aio_poll_wake() always complete the request
inline if POLLFREE is seen. However, that solution had two bugs.
First, it introduced a deadlock, as it unconditionally locked the aio
context while holding the waitqueue lock, which inverts the normal
locking order. Second, it didn't consider that POLLFREE notifications
are missed while the request has been temporarily de-queued.
The second problem was solved by my previous patch. This patch then
properly fixes the use-after-free by handling POLLFREE in a
deadlock-free way. It does this by taking advantage of the fact that
freeing of the waitqueue is RCU-delayed, similar to what eventpoll does.
Fixes: 2c14fa838c ("aio: implement IOCB_CMD_POLL")
Cc: <stable@vger.kernel.org> # v4.18+
Link: https://lore.kernel.org/r/20211209010455.42744-6-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 363bee27e2 upstream.
Currently, aio_poll_wake() will always remove the poll request from the
waitqueue. Then, if aio_poll_complete_work() sees that none of the
polled events are ready and the request isn't cancelled, it re-adds the
request to the waitqueue. (This can easily happen when polling a file
that doesn't pass an event mask when waking up its waitqueue.)
This is fundamentally broken for two reasons:
1. If a wakeup occurs between vfs_poll() and the request being
re-added to the waitqueue, it will be missed because the request
wasn't on the waitqueue at the time. Therefore, IOCB_CMD_POLL
might never complete even if the polled file is ready.
2. When the request isn't on the waitqueue, there is no way to be
notified that the waitqueue is being freed (which happens when its
lifetime is shorter than the struct file's). This is supposed to
happen via the waitqueue entries being woken up with POLLFREE.
Therefore, leave the requests on the waitqueue until they are actually
completed (or cancelled). To keep track of when aio_poll_complete_work
needs to be scheduled, use new fields in struct poll_iocb. Remove the
'done' field which is now redundant.
Note that this is consistent with how sys_poll() and eventpoll work;
their wakeup functions do *not* remove the waitqueue entries.
Fixes: 2c14fa838c ("aio: implement IOCB_CMD_POLL")
Cc: <stable@vger.kernel.org> # v4.18+
Link: https://lore.kernel.org/r/20211209010455.42744-5-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42288cb44c upstream.
Several ->poll() implementations are special in that they use a
waitqueue whose lifetime is the current task, rather than the struct
file as is normally the case. This is okay for blocking polls, since a
blocking poll occurs within one task; however, non-blocking polls
require another solution. This solution is for the queue to be cleared
before it is freed, using 'wake_up_poll(wq, EPOLLHUP | POLLFREE);'.
However, that has a bug: wake_up_poll() calls __wake_up() with
nr_exclusive=1. Therefore, if there are multiple "exclusive" waiters,
and the wakeup function for the first one returns a positive value, only
that one will be called. That's *not* what's needed for POLLFREE;
POLLFREE is special in that it really needs to wake up everyone.
Considering the three non-blocking poll systems:
- io_uring poll doesn't handle POLLFREE at all, so it is broken anyway.
- aio poll is unaffected, since it doesn't support exclusive waits.
However, that's fragile, as someone could add this feature later.
- epoll doesn't appear to be broken by this, since its wakeup function
returns 0 when it sees POLLFREE. But this is fragile.
Although there is a workaround (see epoll), it's better to define a
function which always sends POLLFREE to all waiters. Add such a
function. Also make it verify that the queue really becomes empty after
all waiters have been woken up.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211209010455.42744-2-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a66307d473 upstream.
The ASMedia 1092 has a configuration mode which will present a
dummy device; sadly the implementation falsely claims to provide
a device with 100M which doesn't actually exist.
So disable this device to avoid errors during boot.
Cc: stable@vger.kernel.org
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f58ac1adc7 upstream.
With the design of this driver, this condition is often triggered.
However, the counter that this interrupt indicates an overflow is never
read either, so overflowing is harmless.
On my system, when a CAN bus starts flapping up and down, this locks up
the whole system with lots of interrupts and printks.
Specifically, this interrupt indicates the CEL field of ECR has
overflowed. All reads of ECR mask out CEL.
Fixes: e0d1f4816f ("can: m_can: add Bosch M_CAN controller support")
Link: https://lore.kernel.org/all/20211129222628.7490-1-brian.silverman@bluerivertech.com
Cc: stable@vger.kernel.org
Signed-off-by: Brian Silverman <brian.silverman@bluerivertech.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b19926d4f3 upstream.
dma_fence_chain_find_seqno only ever returns the top fence in the
chain or an unsignalled fence. Hence if we request a seqno that
is already signalled it returns a NULL fence. Some callers are
not prepared to handle this, like the syncobj transfer functions
for example.
This behavior is "new" with timeline syncobj and it looks like
not all callers were updated. To fix this behavior make sure
that a successful drm_sync_find_fence always returns a non-NULL
fence.
v2: Move the fix to drm_syncobj_find_fence from the transfer
functions.
Fixes: ea569910cb ("drm/syncobj: add transition iotcls between binary and timeline v2")
Cc: stable@vger.kernel.org
Signed-off-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Reviewed-by: Christian König <christian.koenig@amd.com>
Acked-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211208023935.17018-1-bas@basnieuwenhuizen.nl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 548ec0805c upstream.
A delegation break could arrive as soon as we've called vfs_setlease. A
delegation break runs a callback which immediately (in
nfsd4_cb_recall_prepare) adds the delegation to del_recall_lru. If we
then exit nfs4_set_delegation without hashing the delegation, it will be
freed as soon as the callback is done with it, without ever being
removed from del_recall_lru.
Symptoms show up later as use-after-free or list corruption warnings,
usually in the laundromat thread.
I suspect aba2072f45 "nfsd: grant read delegations to clients holding
writes" made this bug easier to hit, but I looked as far back as v3.0
and it looks to me it already had the same problem. So I'm not sure
where the bug was introduced; it may have been there from the beginning.
Cc: stable@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 55df1ce0d4 upstream.
The superblock of version 1.0 doesn't get moved to the new position on a
device size change. This leads to a rdev without a superblock on a known
position, the raid can't be re-assembled.
The line was removed by mistake and is re-added by this patch.
Fixes: d9c0fa509e ("md: fix max sectors calculation for super 1.0")
Cc: stable@vger.kernel.org
Signed-off-by: Markus Hochholdinger <markus@hochholdinger.net>
Reviewed-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8289ed9f93 upstream.
I hit the BUG_ON() with generic/475 test case, and to my surprise, all
callers of btrfs_del_root_ref() are already aborting transaction, thus
there is not need for such BUG_ON(), just go to @out label and caller
will properly handle the error.
CC: stable@vger.kernel.org # 5.4+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2e3930529 upstream.
I got dmesg errors on generic/281 on our overnight fstests. Looking at
the history this happens occasionally, with errors like this
WARNING: CPU: 0 PID: 673217 at fs/btrfs/extent_io.c:6848 assert_eb_page_uptodate+0x3f/0x50
CPU: 0 PID: 673217 Comm: kworker/u4:13 Tainted: G W 5.16.0-rc2+ #469
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.13.0-2.fc32 04/01/2014
Workqueue: btrfs-cache btrfs_work_helper
RIP: 0010:assert_eb_page_uptodate+0x3f/0x50
RSP: 0018:ffffae598230bc60 EFLAGS: 00010246
RAX: 0017ffffc0002112 RBX: ffffebaec4100900 RCX: 0000000000001000
RDX: ffffebaec45733c7 RSI: ffffebaec4100900 RDI: ffff9fd98919f340
RBP: 0000000000000d56 R08: ffff9fd98e300000 R09: 0000000000000000
R10: 0001207370a91c50 R11: 0000000000000000 R12: 00000000000007b0
R13: ffff9fd98919f340 R14: 0000000001500000 R15: 0000000001cb0000
FS: 0000000000000000(0000) GS:ffff9fd9fbc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f549fcf8940 CR3: 0000000114908004 CR4: 0000000000370ef0
Call Trace:
extent_buffer_test_bit+0x3f/0x70
free_space_test_bit+0xa6/0xc0
load_free_space_tree+0x1d6/0x430
caching_thread+0x454/0x630
? rcu_read_lock_sched_held+0x12/0x60
? rcu_read_lock_sched_held+0x12/0x60
? rcu_read_lock_sched_held+0x12/0x60
? lock_release+0x1f0/0x2d0
btrfs_work_helper+0xf2/0x3e0
? lock_release+0x1f0/0x2d0
? finish_task_switch.isra.0+0xf9/0x3a0
process_one_work+0x270/0x5a0
worker_thread+0x55/0x3c0
? process_one_work+0x5a0/0x5a0
kthread+0x174/0x1a0
? set_kthread_struct+0x40/0x40
ret_from_fork+0x1f/0x30
This happens because we're trying to read from a extent buffer page that
is !PageUptodate. This happens because we will clear the page uptodate
when we have an IO error, but we don't clear the extent buffer uptodate.
If we do a read later and find this extent buffer we'll think its valid
and not return an error, and then trip over this warning.
Fix this by also clearing uptodate on the extent buffer when this
happens, so that we get an error when we do a btrfs_search_slot() and
find this block later.
CC: stable@vger.kernel.org # 5.4+
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 619764cc2e upstream.
This fixes the SND_PCI_QUIRK(...) of the TongFang PHxTxX1 barebone. This
fixes the issue of sound not working after s3 suspend.
When waking up from s3 suspend the Coef 0x10 is set to 0x0220 instead of
0x0020. Setting the value manually makes the sound work again. This patch
does this automatically.
While being on it, I also fixed the comment formatting of the quirk and
shortened variable and function names.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Fixes: dd6dd6e3c7 ("ALSA: hda/realtek: Add quirk for TongFang PHxTxX1")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211202165010.876431-1-wse@tuxedocomputers.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6409dd6bd upstream.
When control_compat.c:copy_ctl_value_to_user() is used, by
ctl_elem_read_user() & ctl_elem_write_user(), it must also copy back the
snd_ctl_elem_id value that may have been updated (filled in) by the call
to snd_ctl_elem_read/snd_ctl_elem_write().
This matches the functionality provided by snd_ctl_elem_read_user() and
snd_ctl_elem_write_user(), via snd_ctl_build_ioff().
Without this, and without making additional calls to snd_ctl_info()
which are unnecessary when using the non-compat calls, a userspace
application will not know the numid value for the element and
consequently will not be able to use the poll/read interface on the
control file to determine which elements have updates.
Signed-off-by: Alan Young <consult.awy@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211202150607.543389-1-consult.awy@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ebfaa11eb upstream.
Prior to commit 0baedd7927 ("KVM: x86: make Hyper-V PV TLB flush use
tlb_flush_guest()"), kvm_hv_flush_tlb() was using 'KVM_REQ_TLB_FLUSH |
KVM_REQUEST_NO_WAKEUP' when making a request to flush TLBs on other vCPUs
and KVM_REQ_TLB_FLUSH is/was defined as:
(0 | KVM_REQUEST_WAIT | KVM_REQUEST_NO_WAKEUP)
so KVM_REQUEST_WAIT was lost. Hyper-V TLFS, however, requires that
"This call guarantees that by the time control returns back to the
caller, the observable effects of all flushes on the specified virtual
processors have occurred." and without KVM_REQUEST_WAIT there's a small
chance that the vCPU making the TLB flush will resume running before
all IPIs get delivered to other vCPUs and a stale mapping can get read
there.
Fix the issue by adding KVM_REQUEST_WAIT flag to KVM_REQ_TLB_FLUSH_GUEST:
kvm_hv_flush_tlb() is the sole caller which uses it for
kvm_make_all_cpus_request()/kvm_make_vcpus_request_mask() where
KVM_REQUEST_WAIT makes a difference.
Cc: stable@kernel.org
Fixes: 0baedd7927 ("KVM: x86: make Hyper-V PV TLB flush use tlb_flush_guest()")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20211209102937.584397-1-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a1aa356dd upstream.
iavf_set_ringparams doesn't communicate to the user that
1. The user requested descriptor count is out of range. Instead it
just quietly sets descriptors to the "clamped" value and calls it
done. This makes it look an invalid value was successfully set as
the descriptor count when this isn't actually true.
2. The user provided descriptor count needs to be inflated for alignment
reasons.
This behavior is confusing. The ice driver has already addressed this
by rejecting invalid values for descriptor count and
messaging for alignment adjustments.
Do the same thing here by adding the error and info messages.
Fixes: fbb7ddfef2 ("i40evf: core ethtool functionality")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Michal Maloszewski <michal.maloszewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e4dcc1396 upstream.
If the PF experiences an FLR, the VF's MSI and MSI-X configuration will
be conveniently and silently removed in the process. When this happens,
reset recovery will appear to complete normally but no traffic will
pass. The netdev watchdog will helpfully notify everyone of this issue.
To prevent such public embarrassment, restore MSI configuration at every
reset. For normal resets, this will do no harm, but for VF resets
resulting from a PF FLR, this will keep the VF working.
Fixes: 5eae00c57f ("i40evf: main driver core")
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae68d93354 upstream.
When an IPv4 packet is received, the ip_rcv_core(...) sets the receiving
interface index into the IPv4 socket control block (v5.16-rc4,
net/ipv4/ip_input.c line 510):
IPCB(skb)->iif = skb->skb_iif;
If that IPv4 packet is meant to be encapsulated in an outer IPv6+SRH
header, the seg6_do_srh_encap(...) performs the required encapsulation.
In this case, the seg6_do_srh_encap function clears the IPv6 socket control
block (v5.16-rc4 net/ipv6/seg6_iptunnel.c line 163):
memset(IP6CB(skb), 0, sizeof(*IP6CB(skb)));
The memset(...) was introduced in commit ef489749aa ("ipv6: sr: clear
IP6CB(skb) on SRH ip4ip6 encapsulation") a long time ago (2019-01-29).
Since the IPv6 socket control block and the IPv4 socket control block share
the same memory area (skb->cb), the receiving interface index info is lost
(IP6CB(skb)->iif is set to zero).
As a side effect, that condition triggers a NULL pointer dereference if
commit 0857d6f8c7 ("ipv6: When forwarding count rx stats on the orig
netdev") is applied.
To fix that issue, we set the IP6CB(skb)->iif with the index of the
receiving interface once again.
Fixes: ef489749aa ("ipv6: sr: clear IP6CB(skb) on SRH ip4ip6 encapsulation")
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20211208195409.12169-1-andrea.mayer@uniroma2.it
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c56c96303e upstream.
In line 800 (#1), nfp_cpp_area_alloc() allocates and initializes a
CPP area structure. But in line 807 (#2), when the cache is allocated
failed, this CPP area structure is not freed, which will result in
memory leak.
We can fix it by freeing the CPP area when the cache is allocated
failed (#2).
792 int nfp_cpp_area_cache_add(struct nfp_cpp *cpp, size_t size)
793 {
794 struct nfp_cpp_area_cache *cache;
795 struct nfp_cpp_area *area;
800 area = nfp_cpp_area_alloc(cpp, NFP_CPP_ID(7, NFP_CPP_ACTION_RW, 0),
801 0, size);
// #1: allocates and initializes
802 if (!area)
803 return -ENOMEM;
805 cache = kzalloc(sizeof(*cache), GFP_KERNEL);
806 if (!cache)
807 return -ENOMEM; // #2: missing free
817 return 0;
818 }
Fixes: 4cb584e0ee ("nfp: add CPP access core")
Signed-off-by: Jianglei Nie <niejianglei2021@163.com>
Acked-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20211209061511.122535-1-niejianglei2021@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28dc1b86f8 upstream.
If the hardware is constantly receiving unicast or broadcast packets
during driver load, the device previously counted many GLV_RDPC (VSI
dropped packets) events during init. This causes confusing dropped
packet statistics during driver load. The dropped packets counter
incrementing does stop once the driver finishes loading.
Avoid this problem by baselining our statistics at the end of driver
open instead of the end of probe.
Fixes: cdedef59de ("ice: Configure VSIs for Tx/Rx")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2fa7d94afc upstream.
The first commit cited below attempts to fix the off-by-one error that
appeared in some comparisons with an open range. Due to this error,
arithmetically equivalent pieces of code could get different verdicts
from the verifier, for example (pseudocode):
// 1. Passes the verifier:
if (data + 8 > data_end)
return early
read *(u64 *)data, i.e. [data; data+7]
// 2. Rejected by the verifier (should still pass):
if (data + 7 >= data_end)
return early
read *(u64 *)data, i.e. [data; data+7]
The attempted fix, however, shifts the range by one in a wrong
direction, so the bug not only remains, but also such piece of code
starts failing in the verifier:
// 3. Rejected by the verifier, but the check is stricter than in #1.
if (data + 8 >= data_end)
return early
read *(u64 *)data, i.e. [data; data+7]
The change performed by that fix converted an off-by-one bug into
off-by-two. The second commit cited below added the BPF selftests
written to ensure than code chunks like #3 are rejected, however,
they should be accepted.
This commit fixes the off-by-two error by adjusting new_range in the
right direction and fixes the tests by changing the range into the
one that should actually fail.
Fixes: fb2a311a31 ("bpf: fix off by one for range markings with L{T, E} patterns")
Fixes: b37242c773 ("bpf: add test cases to bpf selftests to cover all access tests")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20211130181607.593149-1-maximmi@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f45b2974cc upstream.
The arch_prepare_bpf_dispatcher function does not have a prototype, and
yields the following warning when W=1 is enabled for the kernel build.
>> arch/x86/net/bpf_jit_comp.c:2188:5: warning: no previous \
prototype for 'arch_prepare_bpf_dispatcher' [-Wmissing-prototypes]
2188 | int arch_prepare_bpf_dispatcher(void *image, s64 *funcs, \
int num_funcs)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~
Remove the warning by adding a function declaration to include/linux/bpf.h.
Fixes: 75ccbef636 ("bpf: Introduce BPF dispatcher")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Björn Töpel <bjorn@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20211117125708.769168-1-bjorn@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d43b75fbc2 upstream.
After the below patch, the conntrack attached to skb is set to "notrack" in
the context of vrf device, for locally generated packets.
But this is true only when the default qdisc is set to the vrf device. When
changing the qdisc, notrack is not set anymore.
In fact, there is a shortcut in the vrf driver, when the default qdisc is
set, see commit dcdd43c41e ("net: vrf: performance improvements for
IPv4") for more details.
This patch ensures that the behavior is always the same, whatever the qdisc
is.
To demonstrate the difference, a new test is added in conntrack_vrf.sh.
Fixes: 8c9c296adf ("vrf: run conntrack only in context of lower/physdev for locally generated packets")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Florian Westphal <fw@strlen.de>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ff2fc0286 upstream.
Reserving memory using efi_mem_reserve() calls into the x86
efi_arch_mem_reserve() function. This function will insert a new EFI
memory descriptor into the EFI memory map representing the area of
memory to be reserved and marking it as EFI runtime memory. As part
of adding this new entry, a new EFI memory map is allocated and mapped.
The mapping is where a problem can occur. This new memory map is mapped
using early_memremap() and generally mapped encrypted, unless the new
memory for the mapping happens to come from an area of memory that is
marked as EFI_BOOT_SERVICES_DATA memory. In this case, the new memory will
be mapped unencrypted. However, during replacement of the old memory map,
efi_mem_type() is disabled, so the new memory map will now be long-term
mapped encrypted (in efi.memmap), resulting in the map containing invalid
data and causing the kernel boot to crash.
Since it is known that the area will be mapped encrypted going forward,
explicitly map the new memory map as encrypted using early_memremap_prot().
Cc: <stable@vger.kernel.org> # 4.14.x
Fixes: 8f716c9b5f ("x86/mm: Add support to access boot related data in the clear")
Link: https://lore.kernel.org/all/ebf1eb2940405438a09d51d121ec0d02c8755558.1634752931.git.thomas.lendacky@amd.com/
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
[ardb: incorporate Kconfig fix by Arnd]
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb12797ab1 upstream.
The CAN clock frequency is used when calculating the CAN bittiming
parameters. When wrong clock frequency is used, the device may end up
with wrong bittiming parameters, depending on user requested bittiming
parameters.
To avoid this, get the CAN clock frequency from the device. Various
existing Kvaser Leaf products use different CAN clocks.
Fixes: 080f40a6fa ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Link: https://lore.kernel.org/all/20211208152122.250852-2-extja@kvaser.com
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60a8b5a161 upstream.
This buffer is currently allocated in hfi1_init():
if (reinit)
ret = init_after_reset(dd);
else
ret = loadtime_init(dd);
if (ret)
goto done;
/* allocate dummy tail memory for all receive contexts */
dd->rcvhdrtail_dummy_kvaddr = dma_alloc_coherent(&dd->pcidev->dev,
sizeof(u64),
&dd->rcvhdrtail_dummy_dma,
GFP_KERNEL);
if (!dd->rcvhdrtail_dummy_kvaddr) {
dd_dev_err(dd, "cannot allocate dummy tail memory\n");
ret = -ENOMEM;
goto done;
}
The reinit triggered path will overwrite the old allocation and leak it.
Fix by moving the allocation to hfi1_alloc_devdata() and the deallocation
to hfi1_free_devdata().
Link: https://lore.kernel.org/r/20211129192008.101968.91302.stgit@awfm-01.cornelisnetworks.com
Cc: stable@vger.kernel.org
Fixes: 46b010d3ee ("staging/rdma/hfi1: Workaround to prevent corruption during packet delivery")
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7e945e228 upstream.
The sixth byte of packet data has to be looked up in the sixth group,
not in the seventh one, even if we load the bucket data into ymm6
(and not ymm5, for convenience of tracking stalls).
Without this fix, matching on a MAC address as first field of a set,
if 8-bit groups are selected (due to a small set size) would fail,
that is, the given MAC address would never match.
Reported-by: Nikita Yushchenko <nikita.yushchenko@virtuozzo.com>
Cc: <stable@vger.kernel.org> # 5.6.x
Fixes: 7400b06396 ("nft_set_pipapo: Introduce AVX2-based lookup implementation")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Tested-By: Nikita Yushchenko <nikita.yushchenko@virtuozzo.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9003fbe0f3 upstream.
Add a HID_QUIRK_NO_INIT_REPORTS quirk for the
Microsoft Surface 3 (non pro) type-cover.
Trying to init the reports seems to confuse the type-cover and
causes 2 issues:
1. Despite hid-multitouch sending the command to switch the
touchpad to multitouch mode, it keeps sending events on the
mouse emulation interface.
2. The touchpad completely stops sending events after a reboot.
Adding the HID_QUIRK_NO_INIT_REPORTS quirk fixes both issues.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67a5a68013 upstream.
Fedora Rawhide has started including gcc 11,and the g++ compiler
throws a wobbly when it hits scripts/gcc-plugins:
HOSTCXX scripts/gcc-plugins/latent_entropy_plugin.so
In file included from /usr/include/c++/11/type_traits:35,
from /usr/lib/gcc/x86_64-redhat-linux/11/plugin/include/system.h:244,
from /usr/lib/gcc/x86_64-redhat-linux/11/plugin/include/gcc-plugin.h:28,
from scripts/gcc-plugins/gcc-common.h:7,
from scripts/gcc-plugins/latent_entropy_plugin.c:78:
/usr/include/c++/11/bits/c++0x_warning.h:32:2: error: #error This file requires compiler and library support for the ISO
C++ 2011 standard. This support must be enabled with the -std=c++11 or -std=gnu++11 compiler options.
32 | #error This file requires compiler and library support \
In fact, it works just fine with c++11, which has been in gcc since 4.8,
and we now require 4.9 as a minimum.
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/82487.1609006918@turing-police
Cc: Thomas Lindroth <thomas.lindroth@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e860048c5 upstream.
Linus pointed out a third of the time in the Kconfig parse stage comes
from the single invocation of cc1plus in scripts/gcc-plugin.sh [1],
and directly testing plugin-version.h for existence cuts down the
overhead a lot. [2]
This commit takes one step further to kill the build test entirely.
The small piece of code was probably intended to test the C++ designated
initializer, which was not supported until C++20.
In fact, with -pedantic option given, both GCC and Clang emit a warning.
$ echo 'class test { public: int test; } test = { .test = 1 };' | g++ -x c++ -pedantic - -fsyntax-only
<stdin>:1:43: warning: C++ designated initializers only available with '-std=c++2a' or '-std=gnu++2a' [-Wpedantic]
$ echo 'class test { public: int test; } test = { .test = 1 };' | clang++ -x c++ -pedantic - -fsyntax-only
<stdin>:1:43: warning: designated initializers are a C++20 extension [-Wc++20-designator]
class test { public: int test; } test = { .test = 1 };
^
1 warning generated.
Otherwise, modern C++ compilers should be able to build the code, and
hopefully skipping this test should not make any practical problem.
Checking the existence of plugin-version.h is still needed to ensure
the plugin-dev package is installed. The test code is now small enough
to be embedded in scripts/gcc-plugins/Kconfig.
[1] https://lore.kernel.org/lkml/CAHk-=wjU4DCuwQ4pXshRbwDCUQB31ScaeuDo1tjoZ0_PjhLHzQ@mail.gmail.com/
[2] https://lore.kernel.org/lkml/CAHk-=whK0aQxs6Q5ijJmYF1n2ch8cVFSUzU5yUM_HOjig=+vnw@mail.gmail.com/
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20201203125700.161354-1-masahiroy@kernel.org
Cc: Thomas Lindroth <thomas.lindroth@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72ee48ee89 upstream.
Currently, the UVC function is activated when open on the corresponding
v4l2 device is called. On another open the activation of the function
fails since the deactivation counter in `usb_function_activate` equals
0. However the error is not returned to userspace since the open of the
v4l2 device is successful.
On a close the function is deactivated (since deactivation counter still
equals 0) and the video is disabled in `uvc_v4l2_release`, although the
UVC application potentially is streaming.
Move activation of UVC function to subscription on UVC_EVENT_SETUP
because there we can guarantee for a userspace application utilizing
UVC. Block subscription on UVC_EVENT_SETUP while another application
already is subscribed to it, indicated by `bool func_connected` in
`struct uvc_device`. Extend the `struct uvc_file_handle` with member
`bool is_uvc_app_handle` to tag it as the handle used by the userspace
UVC application.
With this a process is able to check capabilities of the v4l2 device
without deactivating the function for the actual UVC application.
Reviewed-By: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Thomas Haemmerle <thomas.haemmerle@wolfvision.net>
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Acked-by: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/20211003201355.24081-1-m.grzeschik@pengutronix.de
Cc: Dan Vacura <W36195@motorola.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5961060692 upstream.
When the TLS cipher suite uses CCM mode, including AES CCM and
SM4 CCM, the first byte of the B0 block is flags, and the real
IV starts from the second byte. The XOR operation of the IV and
rec_seq should be skip this byte, that is, add the iv_offset.
Fixes: f295b3ae9f ("net/tls: Add support of AES128-CCM based ciphers")
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Cc: Vakul Garg <vakul.garg@nxp.com>
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit afdb4a5b1d upstream.
In commit c8c3735997 ("parisc: Enhance detection of synchronous cr16
clocksources") I assumed that CPUs on the same physical core are syncronous.
While booting up the kernel on two different C8000 machines, one with a
dual-core PA8800 and one with a dual-core PA8900 CPU, this turned out to be
wrong. The symptom was that I saw a jump in the internal clocks printed to the
syslog and strange overall behaviour. On machines which have 4 cores (2
dual-cores) the problem isn't visible, because the current logic already marked
the cr16 clocksource unstable in this case.
This patch now marks the cr16 interval timers unstable if we have more than one
CPU in the system, and it fixes this issue.
Fixes: c8c3735997 ("parisc: Enhance detection of synchronous cr16 clocksources")
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org> # v5.15+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f85e04503f upstream.
Commit f45709df77 ("serial: 8250: Don't touch RTS modem control while
in rs485 mode") sought to prevent user space from interfering with rs485
communication by ignoring a TIOCMSET ioctl() which changes RTS polarity.
It did so in serial8250_do_set_mctrl(), which turns out to be too deep
in the call stack: When a uart_port is opened, RTS polarity is set by
the rs485-aware function uart_port_dtr_rts(). It calls down to
serial8250_do_set_mctrl() and that particular RTS polarity change should
*not* be ignored.
The user-visible result is that on 8250_omap ports which use rs485 with
inverse polarity (RTS bit in MCR register is 1 to receive, 0 to send),
a newly opened port initially sets up RTS for sending instead of
receiving. That's because omap_8250_startup() sets the cached value
up->mcr to 0 and omap_8250_restore_regs() subsequently writes it to the
MCR register. Due to the commit, serial8250_do_set_mctrl() preserves
that incorrect register value:
do_sys_openat2
do_filp_open
path_openat
vfs_open
do_dentry_open
chrdev_open
tty_open
uart_open
tty_port_open
uart_port_activate
uart_startup
uart_port_startup
serial8250_startup
omap_8250_startup # up->mcr = 0
uart_change_speed
serial8250_set_termios
omap_8250_set_termios
omap_8250_restore_regs
serial8250_out_MCR # up->mcr written
tty_port_block_til_ready
uart_dtr_rts
uart_port_dtr_rts
serial8250_set_mctrl
omap8250_set_mctrl
serial8250_do_set_mctrl # mcr[1] = 1 ignored
Fix by intercepting RTS changes from user space in uart_tiocmset()
instead.
Link: https://lore.kernel.org/linux-serial/20211027111644.1996921-1-baocheng.su@siemens.com/
Fixes: f45709df77 ("serial: 8250: Don't touch RTS modem control while in rs485 mode")
Cc: Chao Zeng <chao.zeng@siemens.com>
Cc: stable@vger.kernel.org # v5.7+
Reported-by: Su Bao Cheng <baocheng.su@siemens.com>
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Tested-by: Su Bao Cheng <baocheng.su@siemens.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/21170e622a1aaf842a50b32146008b5374b3dd1d.1637596432.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 00de977f9e upstream.
Commit 761ed4a945 ("tty: serial_core: convert uart_close to use
tty_port_close") converted serial core to use tty_port_close() but
failed to notice that the transmit buffer still needs to be freed on
final close.
Not freeing the transmit buffer means that the buffer is no longer
cleared on next open so that any ioctl() waiting for the buffer to drain
might wait indefinitely (e.g. on termios changes) or that stale data can
end up being transmitted in case tx is restarted.
Furthermore, the buffer of any port that has been opened would leak on
driver unbind.
Note that the port lock is held when clearing the buffer pointer due to
the ldisc race worked around by commit a5ba1d95e4 ("uart: fix race
between uart_put_char() and uart_shutdown()").
Also note that the tty-port shutdown() callback is not called for
console ports so it is not strictly necessary to free the buffer page
after releasing the lock (cf. d72402145a ("tty/serial: do not free
trasnmit buffer page under port lock")).
Link: https://lore.kernel.org/r/319321886d97c456203d5c6a576a5480d07c3478.1635781688.git.baruch@tkos.co.il
Fixes: 761ed4a945 ("tty: serial_core: convert uart_close to use tty_port_close")
Cc: stable@vger.kernel.org # 4.9
Cc: Rob Herring <robh@kernel.org>
Reported-by: Baruch Siach <baruch@tkos.co.il>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211108085431.12637-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b40de7469e upstream.
The current implementation uses 0 as lower limit for the baud rate
tolerance for tegra20 and tegra30 chips which causes isses on UART
initialization as soon as baud rate clock is lower than required even
when within the standard UART tolerance of +/- 4%.
This fix aligns the implementation with the initial commit description
of +/- 4% tolerance for tegra chips other than tegra186 and
tegra194.
Fixes: d781ec21ba ("serial: tegra: report clk rate errors")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Patrik John <patrik.john@u-blox.com>
Link: https://lore.kernel.org/r/sig.19614244f8.20211123132737.88341-1-patrik.john@u-blox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac442a077a upstream.
The document 'ACPI for Arm Components 1.0' defines the following
_HID mappings:
-'Prime cell UART (PL011)': ARMH0011
-'SBSA UART': ARMHB000
Use the sbsa-uart driver when a device is described with
the 'ARMHB000' _HID.
Note:
PL011 devices currently use the sbsa-uart driver instead of the
uart-pl011 driver. Indeed, PL011 devices are not bound to a clock
in ACPI. It is not possible to change their baudrate.
Cc: <stable@vger.kernel.org>
Signed-off-by: Pierre Gondois <Pierre.Gondois@arm.com>
Link: https://lore.kernel.org/r/20211109172248.19061-1-Pierre.Gondois@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7492ffc90f upstream.
The CONSOLE_POLLING mode is used for tools like k(g)db. In this kind of
setup, it is often sharing a serial device with the normal system console.
This is usually no problem because the polling helpers can consume input
values directly (when in kgdb context) and the normal Linux handlers can
only consume new input values after kgdb switched back.
This is not true anymore when RX DMA is enabled for UARTDM controllers.
Single input values can no longer be received correctly. Instead following
seems to happen:
* on 1. input, some old input is read (continuously)
* on 2. input, two old inputs are read (continuously)
* on 3. input, three old input values are read (continuously)
* on 4. input, 4 previous inputs are received
This repeats then for each group of 4 input values.
This behavior changes slightly depending on what state the controller was
when the first input was received. But this makes working with kgdb
basically impossible because control messages are always corrupted when
kgdboc tries to parse them.
RX DMA should therefore be off when CONSOLE_POLLING is enabled to avoid
these kind of problems. No such problem was noticed for TX DMA.
Fixes: 9969394501 ("tty: serial: msm: Add RX DMA support")
Cc: stable@vger.kernel.org
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Link: https://lore.kernel.org/r/20211113121050.7266-1-sven@narfation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51523ed1c2 upstream.
The trampoline_pgd only maps the 0xfffffff000000000-0xffffffffffffffff
range of kernel memory (with 4-level paging). This range contains the
kernel's text+data+bss mappings and the module mapping space but not the
direct mapping and the vmalloc area.
This is enough to get the application processors out of real-mode, but
for code that switches back to real-mode the trampoline_pgd is missing
important parts of the address space. For example, consider this code
from arch/x86/kernel/reboot.c, function machine_real_restart() for a
64-bit kernel:
#ifdef CONFIG_X86_32
load_cr3(initial_page_table);
#else
write_cr3(real_mode_header->trampoline_pgd);
/* Exiting long mode will fail if CR4.PCIDE is set. */
if (boot_cpu_has(X86_FEATURE_PCID))
cr4_clear_bits(X86_CR4_PCIDE);
#endif
/* Jump to the identity-mapped low memory code */
#ifdef CONFIG_X86_32
asm volatile("jmpl *%0" : :
"rm" (real_mode_header->machine_real_restart_asm),
"a" (type));
#else
asm volatile("ljmpl *%0" : :
"m" (real_mode_header->machine_real_restart_asm),
"D" (type));
#endif
The code switches to the trampoline_pgd, which unmaps the direct mapping
and also the kernel stack. The call to cr4_clear_bits() will find no
stack and crash the machine. The real_mode_header pointer below points
into the direct mapping, and dereferencing it also causes a crash.
The reason this does not crash always is only that kernel mappings are
global and the CR3 switch does not flush those mappings. But if theses
mappings are not in the TLB already, the above code will crash before it
can jump to the real-mode stub.
Extend the trampoline_pgd to contain all kernel mappings to prevent
these crashes and to make code which runs on this page-table more
robust.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20211202153226.22946-5-joro@8bytes.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b50db7095f upstream.
There are cases that the TSC clocksource is wrongly judged as unstable by
the clocksource watchdog mechanism which tries to validate the TSC against
HPET, PM_TIMER or jiffies. While there is hardly a general reliable way to
check the validity of a watchdog, Thomas Gleixner proposed [1]:
"I'm inclined to lift that requirement when the CPU has:
1) X86_FEATURE_CONSTANT_TSC
2) X86_FEATURE_NONSTOP_TSC
3) X86_FEATURE_NONSTOP_TSC_S3
4) X86_FEATURE_TSC_ADJUST
5) At max. 4 sockets
After two decades of horrors we're finally at a point where TSC seems
to be halfway reliable and less abused by BIOS tinkerers. TSC_ADJUST
was really key as we can now detect even small modifications reliably
and the important point is that we can cure them as well (not pretty
but better than all other options)."
As feature #3 X86_FEATURE_NONSTOP_TSC_S3 only exists on several generations
of Atom processorz, and is always coupled with X86_FEATURE_CONSTANT_TSC
and X86_FEATURE_NONSTOP_TSC, skip checking it, and also be more defensive
to use maximal 2 sockets.
The check is done inside tsc_init() before registering 'tsc-early' and
'tsc' clocksources, as there were cases that both of them had been
wrongly judged as unreliable.
For more background of tsc/watchdog, there is a good summary in [2]
[tglx} Update vs. jiffies:
On systems where the only remaining clocksource aside of TSC is jiffies
there is no way to make this work because that creates a circular
dependency. Jiffies accuracy depends on not missing a periodic timer
interrupt, which is not guaranteed. That could be detected by TSC, but as
TSC is not trusted this cannot be compensated. The consequence is a
circulus vitiosus which results in shutting down TSC and falling back to
the jiffies clocksource which is even more unreliable.
[1]. https://lore.kernel.org/lkml/87eekfk8bd.fsf@nanos.tec.linutronix.de/
[2]. https://lore.kernel.org/lkml/87a6pimt1f.ffs@nanos.tec.linutronix.de/
[ tglx: Refine comment and amend changelog ]
Fixes: 6e3cd95234 ("x86/hpet: Use another crystalball to evaluate HPET usability")
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "Paul E. McKenney" <paulmck@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211117023751.24190-2-feng.tang@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09f736aa95 upstream.
Turns out some xHC controllers require all 64 bits in the CRCR register
to be written to execute a command abort.
The lower 32 bits containing the command abort bit is written first.
In case the command ring stops before we write the upper 32 bits then
hardware may use these upper bits to set the commnd ring dequeue pointer.
Solve this by making sure the upper 32 bits contain a valid command
ring dequeue pointer.
The original patch that only wrote the first 32 to stop the ring went
to stable, so this fix should go there as well.
Fixes: ff0e50d356 ("xhci: Fix command ring pointer corruption while aborting a command")
Cc: stable@vger.kernel.org
Tested-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211126122340.1193239-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3dfac26e2e upstream.
Fix a division by zero in `vgacon_resize' with a backtrace like:
vgacon_resize
vc_do_resize
vgacon_init
do_bind_con_driver
do_unbind_con_driver
fbcon_fb_unbind
do_unregister_framebuffer
do_register_framebuffer
register_framebuffer
__drm_fb_helper_initial_config_and_unlock
drm_helper_hpd_irq_event
dw_hdmi_irq
irq_thread
kthread
caused by `c->vc_cell_height' not having been initialized. This has
only started to trigger with commit 860dafa902 ("vt: Fix character
height handling with VT_RESIZEX"), however the ultimate offender is
commit 50ec42edd9 ("[PATCH] Detaching fbcon: fix vgacon to allow
retaking of the console").
Said commit has added a call to `vc_resize' whenever `vgacon_init' is
called with the `init' argument set to 0, which did not happen before.
And the call is made before a key vgacon boot parameter retrieved in
`vgacon_startup' has been propagated in `vgacon_init' for `vc_resize' to
use to the console structure being worked on. Previously the parameter
was `c->vc_font.height' and now it is `c->vc_cell_height'.
In this particular scenario the registration of fbcon has failed and vt
resorts to vgacon. Now fbcon does have initialized `c->vc_font.height'
somehow, unlike `c->vc_cell_height', which is why this code did not
crash before, but either way the boot parameters should have been copied
to the console structure ahead of the call to `vc_resize' rather than
afterwards, so that first the call has a chance to use them and second
they do not change the console structure to something possibly different
from what was used by `vc_resize'.
Move the propagation of the vgacon boot parameters ahead of the call to
`vc_resize' then. Adjust the comment accordingly.
Fixes: 50ec42edd9 ("[PATCH] Detaching fbcon: fix vgacon to allow retaking of the console")
Cc: stable@vger.kernel.org # v2.6.18+
Reported-by: Wim Osterholt <wim@djo.tudelft.nl>
Reported-by: Pavel V. Panteleev <panteleev_p@mcst.ru>
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2110252317110.58149@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f9fee4cde upstream.
On newer debian releases the debian-provided "installkernel" script is
installed in /usr/sbin. Fix the kernel install.sh script to look for the
script in this directory as well.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org> # v3.13+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d7c29b777 upstream.
Default KBUILD_IMAGE to $(boot)/bzImage if a self-extracting
(CONFIG_PARISC_SELF_EXTRACT=y) kernel is to be built.
This fixes the bindeb-pkg make target.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c07e45553d ]
Commit
18ec54fdd6 ("x86/speculation: Prepare entry code for Spectre v1 swapgs mitigations")
added FENCE_SWAPGS_{KERNEL|USER}_ENTRY for conditional SWAPGS. In
paranoid_entry(), it uses only FENCE_SWAPGS_KERNEL_ENTRY for both
branches. This is because the fence is required for both cases since the
CR3 write is conditional even when PTI is enabled.
But
96b2371413 ("x86/entry/64: Switch CR3 before SWAPGS in paranoid entry")
changed the order of SWAPGS and the CR3 write. And it missed the needed
FENCE_SWAPGS_KERNEL_ENTRY for the user gsbase case.
Add it back by changing the branches so that FENCE_SWAPGS_KERNEL_ENTRY
can cover both branches.
[ bp: Massage, fix typos, remove obsolete comment while at it. ]
Fixes: 96b2371413 ("x86/entry/64: Switch CR3 before SWAPGS in paranoid entry")
Signed-off-by: Lai Jiangshan <laijs@linux.alibaba.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20211126101209.8613-2-jiangshanlai@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 53c9d92409 ]
SWAPGS is used only for interrupts coming from user mode or for
returning to user mode. So there is no reason to use the PARAVIRT
framework, as it can easily be replaced by an ALTERNATIVE depending
on X86_FEATURE_XENPV.
There are several instances using the PV-aware SWAPGS macro in paths
which are never executed in a Xen PV guest. Replace those with the
plain swapgs instruction. For SWAPGS_UNSAFE_STACK the same applies.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20210120135555.32594-5-jgross@suse.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 315c4f8848 ]
Commit d81ae8aac8 ("sched/uclamp: Fix initialization of struct
uclamp_rq") introduced a bug where uclamp_max of the rq is not reset to
match the woken up task's uclamp_max when the rq is idle.
The code was relying on rq->uclamp_max initialized to zero, so on first
enqueue
static inline void uclamp_rq_inc_id(struct rq *rq, struct task_struct *p,
enum uclamp_id clamp_id)
{
...
if (uc_se->value > READ_ONCE(uc_rq->value))
WRITE_ONCE(uc_rq->value, uc_se->value);
}
was actually resetting it. But since commit d81ae8aac8 changed the
default to 1024, this no longer works. And since rq->uclamp_flags is
also initialized to 0, neither above code path nor uclamp_idle_reset()
update the rq->uclamp_max on first wake up from idle.
This is only visible from first wake up(s) until the first dequeue to
idle after enabling the static key. And it only matters if the
uclamp_max of this task is < 1024 since only then its uclamp_max will be
effectively ignored.
Fix it by properly initializing rq->uclamp_flags = UCLAMP_FLAG_IDLE to
ensure uclamp_idle_reset() is called which then will update the rq
uclamp_max value as expected.
Fixes: d81ae8aac8 ("sched/uclamp: Fix initialization of struct uclamp_rq")
Signed-off-by: Qais Yousef <qais.yousef@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Valentin Schneider <Valentin.Schneider@arm.com>
Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Link: https://lkml.kernel.org/r/20211202112033.1705279-1-qais.yousef@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c8f6a2e31 ]
In the native case, PER_CPU_VAR(cpu_tss_rw + TSS_sp0) is the
trampoline stack. But XEN pv doesn't use trampoline stack, so
PER_CPU_VAR(cpu_tss_rw + TSS_sp0) is also the kernel stack.
In that case, source and destination stacks are identical, which means
that reusing swapgs_restore_regs_and_return_to_usermode() in XEN pv
would cause %rsp to move up to the top of the kernel stack and leave the
IRET frame below %rsp.
This is dangerous as it can be corrupted if #NMI / #MC hit as either of
these events occurring in the middle of the stack pushing would clobber
data on the (original) stack.
And, with XEN pv, swapgs_restore_regs_and_return_to_usermode() pushing
the IRET frame on to the original address is useless and error-prone
when there is any future attempt to modify the code.
[ bp: Massage commit message. ]
Fixes: 7f2590a110 ("x86/entry/64: Use a per-CPU trampoline stack for IDT entries")
Signed-off-by: Lai Jiangshan <laijs@linux.alibaba.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lkml.kernel.org/r/20211126101209.8613-4-jiangshanlai@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1367afaa2e ]
The commit
c758907004 ("x86/entry/64: Remove unneeded kernel CR3 switching")
removed a CR3 write in the faulting path of load_gs_index().
But the path's FENCE_SWAPGS_USER_ENTRY has no fence operation if PTI is
enabled, see spectre_v1_select_mitigation().
Rather, it depended on the serializing CR3 write of SWITCH_TO_KERNEL_CR3
and since it got removed, add a FENCE_SWAPGS_KERNEL_ENTRY call to make
sure speculation is blocked.
[ bp: Massage commit message and comment. ]
Fixes: c758907004 ("x86/entry/64: Remove unneeded kernel CR3 switching")
Signed-off-by: Lai Jiangshan <laijs@linux.alibaba.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20211126101209.8613-3-jiangshanlai@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d5379d047 ]
Properly type the operands being passed to __put_user()/__get_user().
Otherwise, these routines truncate data for dependent instructions
(e.g., INSW) and only read/write one byte.
This has been tested by sending a string with REP OUTSW to a port and
then reading it back in with REP INSW on the same port.
Previous behavior was to only send and receive the first char of the
size. For example, word operations for "abcd" would only read/write
"ac". With change, the full string is now written and read back.
Fixes: f980f9c31a (x86/sev-es: Compile early handler code into kernel image)
Signed-off-by: Michael Sterritt <sterritt@google.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Marc Orr <marcorr@google.com>
Reviewed-by: Peter Gonda <pgonda@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Link: https://lkml.kernel.org/r/20211119232757.176201-1-sterritt@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfbb307c62 ]
The error paths in the prepare_vmcs02() function are supposed to set
*entry_failure_code but this path does not. It leads to using an
uninitialized variable in the caller.
Fixes: 71f7347025 ("KVM: nVMX: Load GUEST_IA32_PERF_GLOBAL_CTRL MSR on VM-Entry")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Message-Id: <20211130125337.GB24578@kili>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb1d220da0 ]
If we run the following perf command in an AMD Milan guest:
perf stat \
-e cpu/event=0x1d0/ \
-e cpu/event=0x1c7/ \
-e cpu/umask=0x1f,event=0x18e/ \
-e cpu/umask=0x7,event=0x18e/ \
-e cpu/umask=0x18,event=0x18e/ \
./workload
dmesg will report a #GP warning from an unchecked MSR access
error on MSR_F15H_PERF_CTLx.
This is because according to APM (Revision: 4.03) Figure 13-7,
the bits [35:32] of AMD PerfEvtSeln register is a part of the
event select encoding, which extends the EVENT_SELECT field
from 8 bits to 12 bits.
Opportunistically update pmu->reserved_bits for reserved bit 19.
Reported-by: Jim Mattson <jmattson@google.com>
Fixes: ca724305a2 ("KVM: x86/vPMU: Implement AMD vPMU code for KVM")
Signed-off-by: Like Xu <likexu@tencent.com>
Message-Id: <20211118130320.95997-1-likexu@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 060a0fb721 upstream.
Remove the warn trace message - it's not a correct check here, because
the function can still be called on the device in DOWN state
Fixes: 508f2e3dce ("net: atlantic: split rx and tx per-queue stats")
Signed-off-by: Sameer Saurabh <ssaurabh@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2087ced0fc upstream.
B0 is the main and widespread device revision of atlantic2 HW. In the
current state, driver will incorrectly fetch the statistics for this
revision.
Fixes: 5cfd54d7dc ("net: atlantic: minimal A2 fw_ops")
Signed-off-by: Dmitry Bogdanov <dbezrukov@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 03fa512189 upstream.
Since Half Duplex mode has been deprecated by the firmware, driver should
not advertise Half Duplex speed in ethtool support link speed values.
Fixes: 071a02046c ("net: atlantic: A2: half duplex support")
Signed-off-by: Sameer Saurabh <ssaurabh@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 413d5e09ca upstream.
At the late production stages new dev ids were introduced. These are
now in production, so its important for the driver to recognize these.
And also fix the board caps for AQC115C adapter.
Fixes: b3f0c79cba ("net: atlantic: A2 hw_ops skeleton")
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2465c80223 upstream.
The correct way to reflect firmware version is to use bundle version.
Hence populating the same instead of MAC fw version.
Fixes: c1be0bf092 ("net: atlantic: common functions needed for basic A2 init/deinit hw_ops")
Signed-off-by: Sameer Saurabh <ssaurabh@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa685acd98 upstream.
When 2.5G is advertised, N-Base should be advertised against the T-base
caps. N5G is out of use in baseline code and driver should treat both 5G
and N5G (and also 2.5G and N2.5G) equally from user perspective.
Fixes: 5cfd54d7dc ("net: atlantic: minimal A2 fw_ops")
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa1dcb5646 upstream.
The max waiting period (of 1 ms) while reading the data from FW shared
buffer is too small for certain types of data (e.g., stats). There's a
chance that FW could be updating buffer at the same time and driver
would be unsuccessful in reading data. Firmware manual recommends to
have 1 sec timeout to fix this issue.
Fixes: 5cfd54d7dc ("net: atlantic: minimal A2 fw_ops")
Signed-off-by: Dmitry Bogdanov <dbezrukov@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4840d537c upstream.
In particular, we need to ensure all the necessary blocks are switched
to 64b mode (a5xx+) otherwise the high bits of the address of the BO to
snapshot state into will be ignored, resulting in:
*** gpu fault: ttbr0=0000000000000000 iova=0000000000012000 dir=READ type=TRANSLATION source=CP (0,0,0,0)
platform 506a000.gmu: [drm:a6xx_gmu_set_oob] *ERROR* Timeout waiting for GMU OOB set BOOT_SLUMBER: 0x0
Fixes: 4f776f4511 ("drm/msm/gpu: Convert the GPU show function to use the GPU state")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20211108180122.487859-1-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4d25abf97 upstream.
In commit 142639a52a ("drm/msm/a6xx: fix crashstate capture for
A650") we changed a6xx_get_gmu_registers() to read 3 sets of
registers. Unfortunately, we didn't change the memory allocation for
the array. That leads to a KASAN warning (this was on the chromeos-5.4
kernel, which has the problematic commit backported to it):
BUG: KASAN: slab-out-of-bounds in _a6xx_get_gmu_registers+0x144/0x430
Write of size 8 at addr ffffff80c89432b0 by task A618-worker/209
CPU: 5 PID: 209 Comm: A618-worker Tainted: G W 5.4.156-lockdep #22
Hardware name: Google Lazor Limozeen without Touchscreen (rev5 - rev8) (DT)
Call trace:
dump_backtrace+0x0/0x248
show_stack+0x20/0x2c
dump_stack+0x128/0x1ec
print_address_description+0x88/0x4a0
__kasan_report+0xfc/0x120
kasan_report+0x10/0x18
__asan_report_store8_noabort+0x1c/0x24
_a6xx_get_gmu_registers+0x144/0x430
a6xx_gpu_state_get+0x330/0x25d4
msm_gpu_crashstate_capture+0xa0/0x84c
recover_worker+0x328/0x838
kthread_worker_fn+0x32c/0x574
kthread+0x2dc/0x39c
ret_from_fork+0x10/0x18
Allocated by task 209:
__kasan_kmalloc+0xfc/0x1c4
kasan_kmalloc+0xc/0x14
kmem_cache_alloc_trace+0x1f0/0x2a0
a6xx_gpu_state_get+0x164/0x25d4
msm_gpu_crashstate_capture+0xa0/0x84c
recover_worker+0x328/0x838
kthread_worker_fn+0x32c/0x574
kthread+0x2dc/0x39c
ret_from_fork+0x10/0x18
Fixes: 142639a52a ("drm/msm/a6xx: fix crashstate capture for A650")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20211103153049.1.Idfa574ccb529d17b69db3a1852e49b580132035c@changeid
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 19f36edf14 upstream.
Correct an error where setting /proc/sys/net/rds/tcp/rds_tcp_rcvbuf would
instead modify the socket's sk_sndbuf and would leave sk_rcvbuf untouched.
Fixes: c6a58ffed5 ("RDS: TCP: Add sysctl tunables for sndbuf/rcvbuf on rds-tcp socket")
Signed-off-by: William Kucharski <william.kucharski@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 213f5f8f31 upstream.
Before commit faa041a40b ("ipv4: Create cleanup helper for fib_nh")
changes to net->ipv4.fib_num_tclassid_users were protected by RTNL.
After the change, this is no longer the case, as free_fib_info_rcu()
runs after rcu grace period, without rtnl being held.
Fixes: faa041a40b ("ipv4: Create cleanup helper for fib_nh")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Ahern <dsahern@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f4a8adbfe4 upstream.
The commit c55211892f ("dpaa2-eth: support PTP Sync packet one-step
timestamping") forgets to destroy workqueue at the end of remove
function.
Fix this by adding destroy_workqueue before fsl_mc_portal_free and
free_netdev.
Fixes: c55211892f ("dpaa2-eth: support PTP Sync packet one-step timestamping")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b83f5ac7d9 upstream.
'bitmap_fill()' fills a bitmap one 'long' at a time.
It is likely that an exact number of bits is expected.
Use 'bitmap_set()' instead in order not to set unexpected bits.
Fixes: e531f76757 ("net: mvpp2: handle cases where more CPUs are available than s/w threads")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 817b653160 upstream.
On most systems request for IRQ 0 will fail, phylib will print an error message
and fall back to polling. To fix this set the phydev->irq to PHY_POLL if no IRQ
is available.
Fixes: cc89c323a3 ("lan78xx: Use irq_domain for phy interrupt from USB Int. EP")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Sven Schuchmann <schuchmann@schleissheimer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a05431b22b upstream.
ipv6_addr_bind/ipv4_addr_bind are function names. Previously, bind test
would not be run by default due to the wrong case names
Fixes: 34d0302ab8 ("selftests: Add ipv6 address bind tests to fcnal-test")
Fixes: 75b2b2b3db ("selftests: Add ipv4 address bind tests to fcnal-test")
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit addad76431 upstream.
In mlx4_en_try_alloc_resources(), mlx4_en_copy_priv() is called and
tmp->tx_cq will be freed on the error path of mlx4_en_copy_priv().
After that mlx4_en_alloc_resources() is called and there is a dereference
of &tmp->tx_cq[t][i] in mlx4_en_alloc_resources(), which could lead to
a use after free problem on failure of mlx4_en_copy_priv().
Fix this bug by adding a check of mlx4_en_copy_priv()
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_MLX4_EN=m show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: ec25bc04ed ("net/mlx4_en: Add resilience in low memory systems")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20211130164438.190591-1-zhou1615@umn.edu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 35b6b28e69 upstream.
When branch target identifiers are in use, code reachable via an
indirect branch requires a BTI landing pad at the branch target site.
When building FTRACE_WITH_REGS atop patchable-function-entry, we miss
BTIs at the start start of the `ftrace_caller` and `ftrace_regs_caller`
trampolines, and when these are called from a module via a PLT (which
will use a `BR X16`), we will encounter a BTI failure, e.g.
| # insmod lkdtm.ko
| lkdtm: No crash points registered, enable through debugfs
| # echo function_graph > /sys/kernel/debug/tracing/current_tracer
| # cat /sys/kernel/debug/provoke-crash/DIRECT
| Unhandled 64-bit el1h sync exception on CPU0, ESR 0x34000001 -- BTI
| CPU: 0 PID: 174 Comm: cat Not tainted 5.16.0-rc2-dirty #3
| Hardware name: linux,dummy-virt (DT)
| pstate: 60400405 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=jc)
| pc : ftrace_caller+0x0/0x3c
| lr : lkdtm_debugfs_open+0xc/0x20 [lkdtm]
| sp : ffff800012e43b00
| x29: ffff800012e43b00 x28: 0000000000000000 x27: ffff800012e43c88
| x26: 0000000000000000 x25: 0000000000000000 x24: ffff0000c171f200
| x23: ffff0000c27b1e00 x22: ffff0000c2265240 x21: ffff0000c23c8c30
| x20: ffff8000090ba380 x19: 0000000000000000 x18: 0000000000000000
| x17: 0000000000000000 x16: ffff80001002bb4c x15: 0000000000000000
| x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000900ff0
| x11: ffff0000c4166310 x10: ffff800012e43b00 x9 : ffff8000104f2384
| x8 : 0000000000000001 x7 : 0000000000000000 x6 : 000000000000003f
| x5 : 0000000000000040 x4 : ffff800012e43af0 x3 : 0000000000000001
| x2 : ffff8000090b0000 x1 : ffff0000c171f200 x0 : ffff0000c23c8c30
| Kernel panic - not syncing: Unhandled exception
| CPU: 0 PID: 174 Comm: cat Not tainted 5.16.0-rc2-dirty #3
| Hardware name: linux,dummy-virt (DT)
| Call trace:
| dump_backtrace+0x0/0x1a4
| show_stack+0x24/0x30
| dump_stack_lvl+0x68/0x84
| dump_stack+0x1c/0x38
| panic+0x168/0x360
| arm64_exit_nmi.isra.0+0x0/0x80
| el1h_64_sync_handler+0x68/0xd4
| el1h_64_sync+0x78/0x7c
| ftrace_caller+0x0/0x3c
| do_dentry_open+0x134/0x3b0
| vfs_open+0x38/0x44
| path_openat+0x89c/0xe40
| do_filp_open+0x8c/0x13c
| do_sys_openat2+0xbc/0x174
| __arm64_sys_openat+0x6c/0xbc
| invoke_syscall+0x50/0x120
| el0_svc_common.constprop.0+0xdc/0x100
| do_el0_svc+0x84/0xa0
| el0_svc+0x28/0x80
| el0t_64_sync_handler+0xa8/0x130
| el0t_64_sync+0x1a0/0x1a4
| SMP: stopping secondary CPUs
| Kernel Offset: disabled
| CPU features: 0x0,00000f42,da660c5f
| Memory Limit: none
| ---[ end Kernel panic - not syncing: Unhandled exception ]---
Fix this by adding the required `BTI C`, as we only require these to be
reachable via BL for direct calls or BR X16/X17 for PLTs. For now, these
are open-coded in the function prologue, matching the style of the
`__hwasan_tag_mismatch` trampoline.
In future we may wish to consider adding a new SYM_CODE_START_*()
variant which has an implicit BTI.
When ftrace is built atop mcount, the trampolines are marked with
SYM_FUNC_START(), and so get an implicit BTI. We may need to change
these over to SYM_CODE_START() in future for RELIABLE_STACKTRACE, in
case we need to apply special care aroud the return address being
rewritten.
Fixes: 97fed779f2 ("arm64: bti: Provide Kconfig for kernel mode BTI")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20211129135709.2274019-1-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7e5b9bfa6 upstream.
On ARM v6 and later, we define CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
because the ordinary load/store instructions (ldr, ldrh, ldrb) can
tolerate any misalignment of the memory address. However, load/store
double and load/store multiple instructions (ldrd, ldm) may still only
be used on memory addresses that are 32-bit aligned, and so we have to
use the CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS macro with care, or we
may end up with a severe performance hit due to alignment traps that
require fixups by the kernel. Testing shows that this currently happens
with clang-13 but not gcc-11. In theory, any compiler version can
produce this bug or other problems, as we are dealing with undefined
behavior in C99 even on architectures that support this in hardware,
see also https://gcc.gnu.org/bugzilla/show_bug.cgi?id=100363.
Fortunately, the get_unaligned() accessors do the right thing: when
building for ARMv6 or later, the compiler will emit unaligned accesses
using the ordinary load/store instructions (but avoid the ones that
require 32-bit alignment). When building for older ARM, those accessors
will emit the appropriate sequence of ldrb/mov/orr instructions. And on
architectures that can truly tolerate any kind of misalignment, the
get_unaligned() accessors resolve to the leXX_to_cpup accessors that
operate on aligned addresses.
Since the compiler will in fact emit ldrd or ldm instructions when
building this code for ARM v6 or later, the solution is to use the
unaligned accessors unconditionally on architectures where this is
known to be fast. The _aligned version of the hash function is
however still needed to get the best performance on architectures
that cannot do any unaligned access in hardware.
This new version avoids the undefined behavior and should produce
the fastest hash on all architectures we support.
Link: https://lore.kernel.org/linux-arm-kernel/20181008211554.5355-4-ard.biesheuvel@linaro.org/
Link: https://lore.kernel.org/linux-crypto/CAK8P3a2KfmmGDbVHULWevB0hv71P2oi2ZCHEAqT=8dQfa0=cqQ@mail.gmail.com/
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Fixes: 2c956a6077 ("siphash: add cryptographically secure PRF")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d4741eacd upstream.
There are various problems related to netlink notifications for mpls route
changes in response to interfaces being deleted:
* delete interface of only nexthop
DELROUTE notification is missing RTA_OIF attribute
* delete interface of non-last nexthop
NEWROUTE notification is missing entirely
* delete interface of last nexthop
DELROUTE notification is missing nexthop
All of these problems stem from the fact that existing routes are modified
in-place before sending a notification. Restructure mpls_ifdown() to avoid
changing the route in the DELROUTE cases and to create a copy in the
NEWROUTE case.
Fixes: f8efb73c97 ("mpls: multipath route support")
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e2dabc4f7e upstream.
In qlcnic_83xx_add_rings(), the indirect function of
ahw->hw_ops->alloc_mbx_args will be called to allocate memory for
cmd.req.arg, and there is a dereference of it in qlcnic_83xx_add_rings(),
which could lead to a NULL pointer dereference on failure of the
indirect function like qlcnic_83xx_alloc_mbx_args().
Fix this bug by adding a check of alloc_mbx_args(), this patch
imitates the logic of mbx_cmd()'s failure handling.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_QLCNIC=m show no new warnings, and our
static analyzer no longer warns about this code.
Fixes: 7f9664525f ("qlcnic: 83xx memory map and HW access routine")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Link: https://lore.kernel.org/r/20211130110848.109026-1-zhou1615@umn.edu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dacb5d8875 upstream.
Steffen reported a TCP stream corruption for HTTP requests
served by the apache web-server using a cifs mount-point
and memory mapping the relevant file.
The root cause is quite similar to the one addressed by
commit 20eb4f29b6 ("net: fix sk_page_frag() recursion from
memory reclaim"). Here the nested access to the task page frag
is caused by a page fault on the (mmapped) user-space memory
buffer coming from the cifs file.
The page fault handler performs an smb transaction on a different
socket, inside the same process context. Since sk->sk_allaction
for such socket does not prevent the usage for the task_frag,
the nested allocation modify "under the hood" the page frag
in use by the outer sendmsg call, corrupting the stream.
The overall relevant stack trace looks like the following:
httpd 78268 [001] 3461630.850950: probe:tcp_sendmsg_locked:
ffffffff91461d91 tcp_sendmsg_locked+0x1
ffffffff91462b57 tcp_sendmsg+0x27
ffffffff9139814e sock_sendmsg+0x3e
ffffffffc06dfe1d smb_send_kvec+0x28
[...]
ffffffffc06cfaf8 cifs_readpages+0x213
ffffffff90e83c4b read_pages+0x6b
ffffffff90e83f31 __do_page_cache_readahead+0x1c1
ffffffff90e79e98 filemap_fault+0x788
ffffffff90eb0458 __do_fault+0x38
ffffffff90eb5280 do_fault+0x1a0
ffffffff90eb7c84 __handle_mm_fault+0x4d4
ffffffff90eb8093 handle_mm_fault+0xc3
ffffffff90c74f6d __do_page_fault+0x1ed
ffffffff90c75277 do_page_fault+0x37
ffffffff9160111e page_fault+0x1e
ffffffff9109e7b5 copyin+0x25
ffffffff9109eb40 _copy_from_iter_full+0xe0
ffffffff91462370 tcp_sendmsg_locked+0x5e0
ffffffff91462370 tcp_sendmsg_locked+0x5e0
ffffffff91462b57 tcp_sendmsg+0x27
ffffffff9139815c sock_sendmsg+0x4c
ffffffff913981f7 sock_write_iter+0x97
ffffffff90f2cc56 do_iter_readv_writev+0x156
ffffffff90f2dff0 do_iter_write+0x80
ffffffff90f2e1c3 vfs_writev+0xa3
ffffffff90f2e27c do_writev+0x5c
ffffffff90c042bb do_syscall_64+0x5b
ffffffff916000ad entry_SYSCALL_64_after_hwframe+0x65
The cifs filesystem rightfully sets sk_allocations to GFP_NOFS,
we can avoid the nesting using the sk page frag for allocation
lacking the __GFP_FS flag. Do not define an additional mm-helper
for that, as this is strictly tied to the sk page frag usage.
v1 -> v2:
- use a stricted sk_page_frag() check instead of reordering the
code (Eric)
Reported-by: Steffen Froemer <sfroemer@redhat.com>
Fixes: 5640f76858 ("net: use a per task frag allocator")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b0f38e1597 upstream.
Fix section mismatch warnings in xtsonic. The first one appears to be
bogus and after fixing the second one, the first one is gone.
WARNING: modpost: vmlinux.o(.text+0x529adc): Section mismatch in reference from the function sonic_get_stats() to the function .init.text:set_reset_devices()
The function sonic_get_stats() references
the function __init set_reset_devices().
This is often because sonic_get_stats lacks a __init
annotation or the annotation of set_reset_devices is wrong.
WARNING: modpost: vmlinux.o(.text+0x529b3b): Section mismatch in reference from the function xtsonic_probe() to the function .init.text:sonic_probe1()
The function xtsonic_probe() references
the function __init sonic_probe1().
This is often because xtsonic_probe lacks a __init
annotation or the annotation of sonic_probe1 is wrong.
Fixes: 74f2a5f0ef ("xtensa: Add support for the Sonic Ethernet device for the XT2000 board.")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Chris Zankel <chris@zankel.net>
Cc: linux-xtensa@linux-xtensa.org
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Link: https://lore.kernel.org/r/20211130063947.7529-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b12764695c upstream.
CBUS transfers have always been atomic, but after commit 63b96983a5
("i2c: core: introduce callbacks for atomic transfers") we started to see
warnings during e.g. poweroff as the atomic callback is not explicitly set.
Fix that.
Fixes the following WARNING seen during Nokia N810 power down:
[ 786.570617] reboot: Power down
[ 786.573913] ------------[ cut here ]------------
[ 786.578826] WARNING: CPU: 0 PID: 672 at drivers/i2c/i2c-core.h:40 i2c_smbus_xfer+0x100/0x110
[ 786.587799] No atomic I2C transfer handler for 'i2c-2'
Fixes: 63b96983a5 ("i2c: core: introduce callbacks for atomic transfers")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31b90a95cc upstream.
In case of receiving a NACK, the dma transfer should be stopped
to avoid feeding data into the FIFO.
Also ensure to properly return the proper error code and avoid
waiting for the end of the dma completion in case of
error happening during the transmission.
Fixes: 7ecc8cfde5 ("i2c: i2c-stm32f7: Add DMA support")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c21d02ca4 upstream.
While handling an error during transfer (ex: NACK), it could
happen that the driver has already written data into TXDR
before the transfer get stopped.
This commit add TXDR Flush after end of transfer in case of error to
avoid sending a wrong data on any other slave upon next transfer.
Fixes: aeb068c572 ("i2c: i2c-stm32f7: add driver")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e3fd72171 upstream.
Use 2-factor argument form kvcalloc() instead of kvzalloc().
Link: https://github.com/KSPP/linux/issues/162
Fixes: e7096c131e ("net: WireGuard secure network tunnel")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
[Jason: Gustavo's link above is for KSPP, but this isn't actually a
security fix, as table_size is bounded to 8192 anyway, and gcc realizes
this, so the codegen comes out to be about the same.]
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb32f4f606 upstream.
If we're being delivered packets from multiple CPUs so quickly that the
ring lock is contended for CPU tries, then it's safe to assume that the
queue is near capacity anyway, so just drop the packet rather than
spinning. This helps deal with multicore DoS that can interfere with
data path performance. It _still_ does not completely fix the issue, but
it again chips away at it.
Reported-by: Streun Fabio <fstreun@student.ethz.ch>
Fixes: e7096c131e ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 886fcee939 upstream.
Apparently the spinlock on incoming_handshake's skb_queue is highly
contended, and a torrent of handshake or cookie packets can bring the
data plane to its knees, simply by virtue of enqueueing the handshake
packets to be processed asynchronously. So, we try switching this to a
ring buffer to hopefully have less lock contention. This alleviates the
problem somewhat, though it still isn't perfect, so future patches will
have to improve this further. However, it at least doesn't completely
diminish the data plane.
Reported-by: Streun Fabio <fstreun@student.ethz.ch>
Reported-by: Joel Wanner <joel.wanner@inf.ethz.ch>
Fixes: e7096c131e ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 20ae1d6aa1 upstream.
Each peer's endpoint contains a dst_cache entry that takes a reference
to another netdev. When the containing namespace exits, we take down the
socket and prevent future sockets from being created (by setting
creating_net to NULL), which removes that potential reference on the
netns. However, it doesn't release references to the netns that a netdev
cached in dst_cache might be taking, so the netns still might fail to
exit. Since the socket is gimped anyway, we can simply clear all the
dst_caches (by way of clearing the endpoint src), which will release all
references.
However, the current dst_cache_reset function only releases those
references lazily. But it turns out that all of our usages of
wg_socket_clear_peer_endpoint_src are called from contexts that are not
exactly high-speed or bottle-necked. For example, when there's
connection difficulty, or when userspace is reconfiguring the interface.
And in particular for this patch, when the netns is exiting. So for
those cases, it makes more sense to call dst_release immediately. For
that, we add a small helper function to dst_cache.
This patch also adds a test to netns.sh from Hangbin Liu to ensure this
doesn't regress.
Tested-by: Hangbin Liu <liuhangbin@gmail.com>
Reported-by: Xiumei Mu <xmu@redhat.com>
Cc: Toke Høiland-Jørgensen <toke@redhat.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Fixes: 900575aa33 ("wireguard: device: avoid circular netns references")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 782c72af56 upstream.
We previously removed the restriction on looping to self, and then added
a test to make sure the kernel didn't blow up during a routing loop. The
kernel didn't blow up, thankfully, but on certain architectures where
skb fragmentation is easier, such as ppc64, the skbs weren't actually
being discarded after a few rounds through. But the test wasn't catching
this. So actually test explicitly for massive increases in tx to see if
we have a routing loop. Note that the actual loop problem will need to
be addressed in a different commit.
Fixes: b673e24aad ("wireguard: socket: remove errant restriction on looping to self")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae9287811b upstream.
A __rcu annotation got lost during refactoring, which caused sparse to
become enraged.
Fixes: bf7b042dc6 ("wireguard: allowedips: free empty intermediate nodes when removing single node")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 03ff1b1def upstream.
The selftests currently parse the kernel log at the end to track
potential memory leaks. With these tests now reading off the end of the
buffer, due to recent optimizations, some creation messages were lost,
making the tests think that there was a free without an alloc. Fix this
by increasing the kernel log size.
Fixes: 24b70eeeb4 ("wireguard: use synchronize_net rather than synchronize_rcu")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05b29633c7 upstream.
INVLPG operates on guest virtual address, which are represented by
vcpu->arch.walk_mmu. In nested virtualization scenarios,
kvm_mmu_invlpg() was using the wrong MMU structure; if L2's invlpg were
emulated by L0 (in practice, it hardly happen) when nested two-dimensional
paging is enabled, the call to ->tlb_flush_gva() would be skipped and
the hardware TLB entry would not be invalidated.
Signed-off-by: Lai Jiangshan <laijs@linux.alibaba.com>
Message-Id: <20211124122055.64424-5-jiangshanlai@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f80d15020 upstream.
Having a signed (1 << 31) constant for TCR_EL2_RES1 and CPTR_EL2_TCPAC
causes the upper 32-bit to be set to 1 when assigning them to a 64-bit
variable. Bit 32 in TCR_EL2 is no longer RES0 in ARMv8.7: with FEAT_LPA2
it changes the meaning of bits 49:48 and 9:8 in the stage 1 EL2 page
table entries. As a result of the sign-extension, a non-VHE kernel can
no longer boot on a model with ARMv8.7 enabled.
CPTR_EL2 still has the top 32 bits RES0 but we should preempt any future
problems
Make these top bit constants unsigned as per commit df655b75c4
("arm64: KVM: Avoid setting the upper 32 bits of VTCR_EL2 to 1").
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Chris January <Chris.January@arm.com>
Cc: <stable@vger.kernel.org>
Cc: Will Deacon <will@kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211125152014.2806582-1-catalin.marinas@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 53b7ca1a35 upstream.
Currently, checks for whether VT-d PI can be used refer to the current
status of the feature in the current vCPU; or they more or less pick
vCPU 0 in case a specific vCPU is not available.
However, these checks do not attempt to synchronize with changes to
the IRTE. In particular, there is no path that updates the IRTE when
APICv is re-activated on vCPU 0; and there is no path to wakeup a CPU
that has APICv disabled, if the wakeup occurs because of an IRTE
that points to a posted interrupt.
To fix this, always go through the VT-d PI path as long as there are
assigned devices and APICv is available on both the host and the VM side.
Since the relevant condition was copied over three times, take the hint
and factor it into a separate function.
Suggested-by: Sean Christopherson <seanjc@google.com>
Cc: stable@vger.kernel.org
Reviewed-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: David Matlack <dmatlack@google.com>
Message-Id: <20211123004311.2954158-5-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b4a5a5d56 upstream.
Flush the current VPID when handling KVM_REQ_TLB_FLUSH_GUEST instead of
always flushing vpid01. Any TLB flush that is triggered when L2 is
active is scoped to L2's VPID (if it has one), e.g. if L2 toggles CR4.PGE
and L1 doesn't intercept PGE writes, then KVM's emulation of the TLB
flush needs to be applied to L2's VPID.
Reported-by: Lai Jiangshan <jiangshanlai+lkml@gmail.com>
Fixes: 07ffaf343e ("KVM: nVMX: Sync all PGDs on nested transition with shadow paging")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211125014944.536398-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b285a5587 upstream.
Reject userspace memslots whose size exceeds the storage capacity of an
"unsigned long". KVM's uAPI takes the size as u64 to support large slots
on 64-bit hosts, but does not account for the size being truncated on
32-bit hosts in various flows. The access_ok() check on the userspace
virtual address in particular casts the size to "unsigned long" and will
check the wrong number of bytes.
KVM doesn't actually support slots whose size doesn't fit in an "unsigned
long", e.g. KVM's internal kvm_memory_slot.npages is an "unsigned long",
not a "u64", and misc arch specific code follows that behavior.
Fixes: fa3d315a4c ("KVM: Validate userspace_addr of memslot when registered")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Message-Id: <20211104002531.1176691-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 94ebc03545 upstream.
[Why]
When trying to lightup two 4k60 non-DSC displays behind a branch device
that supports DSC we can't lightup both at once due to bandwidth
limitations - each requires 48 VCPI slots but we only have 63.
[How]
The workaround already exists in the code but is guarded by a CONFIG
that cannot be set by the user and shouldn't need to be.
Check for specific branch device IDs to device whether to enable
the workaround for multiple display scenarios.
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cdef485217 upstream.
The kernel leaks memory when a `fib` rule is present in IPv6 nftables
firewall rules and a suppress_prefix rule is present in the IPv6 routing
rules (used by certain tools such as wg-quick). In such scenarios, every
incoming packet will leak an allocation in `ip6_dst_cache` slab cache.
After some hours of `bpftrace`-ing and source code reading, I tracked
down the issue to ca7a03c417 ("ipv6: do not free rt if
FIB_LOOKUP_NOREF is set on suppress rule").
The problem with that change is that the generic `args->flags` always have
`FIB_LOOKUP_NOREF` set[1][2] but the IPv6-specific flag
`RT6_LOOKUP_F_DST_NOREF` might not be, leading to `fib6_rule_suppress` not
decreasing the refcount when needed.
How to reproduce:
- Add the following nftables rule to a prerouting chain:
meta nfproto ipv6 fib saddr . mark . iif oif missing drop
This can be done with:
sudo nft create table inet test
sudo nft create chain inet test test_chain '{ type filter hook prerouting priority filter + 10; policy accept; }'
sudo nft add rule inet test test_chain meta nfproto ipv6 fib saddr . mark . iif oif missing drop
- Run:
sudo ip -6 rule add table main suppress_prefixlength 0
- Watch `sudo slabtop -o | grep ip6_dst_cache` to see memory usage increase
with every incoming ipv6 packet.
This patch exposes the protocol-specific flags to the protocol
specific `suppress` function, and check the protocol-specific `flags`
argument for RT6_LOOKUP_F_DST_NOREF instead of the generic
FIB_LOOKUP_NOREF when decreasing the refcount, like this.
[1]: ca7a03c417/net/ipv6/fib6_rules.c (L71)
[2]: ca7a03c417/net/ipv6/fib6_rules.c (L99)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215105
Fixes: ca7a03c417 ("ipv6: do not free rt if FIB_LOOKUP_NOREF is set on suppress rule")
Cc: stable@vger.kernel.org
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f48394cf1 upstream.
Trying to remove the fsl-sata module in the PPC64 GNU/Linux
leads to the following warning:
------------[ cut here ]------------
remove_proc_entry: removing non-empty directory 'irq/69',
leaking at least 'fsl-sata[ff0221000.sata]'
WARNING: CPU: 3 PID: 1048 at fs/proc/generic.c:722
.remove_proc_entry+0x20c/0x220
IRQMASK: 0
NIP [c00000000033826c] .remove_proc_entry+0x20c/0x220
LR [c000000000338268] .remove_proc_entry+0x208/0x220
Call Trace:
.remove_proc_entry+0x208/0x220 (unreliable)
.unregister_irq_proc+0x104/0x140
.free_desc+0x44/0xb0
.irq_free_descs+0x9c/0xf0
.irq_dispose_mapping+0x64/0xa0
.sata_fsl_remove+0x58/0xa0 [sata_fsl]
.platform_drv_remove+0x40/0x90
.device_release_driver_internal+0x160/0x2c0
.driver_detach+0x64/0xd0
.bus_remove_driver+0x70/0xf0
.driver_unregister+0x38/0x80
.platform_driver_unregister+0x14/0x30
.fsl_sata_driver_exit+0x18/0xa20 [sata_fsl]
---[ end trace 0ea876d4076908f5 ]---
The driver creates the mapping by calling irq_of_parse_and_map(),
so it also has to dispose the mapping. But the easy way out is to
simply use platform_get_irq() instead of irq_of_parse_map(). Also
we should adapt return value checking and propagate error values.
In this case the mapping is not managed by the device but by
the of core, so the device has not to dispose the mapping.
Fixes: faf0b2e5af ("drivers/ata: add support to Freescale 3.0Gbps SATA Controller")
Cc: stable@vger.kernel.org
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c8ad7e8cf upstream.
When the `rmmod sata_fsl.ko` command is executed in the PPC64 GNU/Linux,
a bug is reported:
==================================================================
BUG: Unable to handle kernel data access on read at 0x80000800805b502c
Oops: Kernel access of bad area, sig: 11 [#1]
NIP [c0000000000388a4] .ioread32+0x4/0x20
LR [80000000000c6034] .sata_fsl_port_stop+0x44/0xe0 [sata_fsl]
Call Trace:
.free_irq+0x1c/0x4e0 (unreliable)
.ata_host_stop+0x74/0xd0 [libata]
.release_nodes+0x330/0x3f0
.device_release_driver_internal+0x178/0x2c0
.driver_detach+0x64/0xd0
.bus_remove_driver+0x70/0xf0
.driver_unregister+0x38/0x80
.platform_driver_unregister+0x14/0x30
.fsl_sata_driver_exit+0x18/0xa20 [sata_fsl]
.__se_sys_delete_module+0x1ec/0x2d0
.system_call_exception+0xfc/0x1f0
system_call_common+0xf8/0x200
==================================================================
The triggering of the BUG is shown in the following stack:
driver_detach
device_release_driver_internal
__device_release_driver
drv->remove(dev) --> platform_drv_remove/platform_remove
drv->remove(dev) --> sata_fsl_remove
iounmap(host_priv->hcr_base); <---- unmap
kfree(host_priv); <---- free
devres_release_all
release_nodes
dr->node.release(dev, dr->data) --> ata_host_stop
ap->ops->port_stop(ap) --> sata_fsl_port_stop
ioread32(hcr_base + HCONTROL) <---- UAF
host->ops->host_stop(host)
The iounmap(host_priv->hcr_base) and kfree(host_priv) functions should
not be executed in drv->remove. These functions should be executed in
host_stop after port_stop. Therefore, we move these functions to the
new function sata_fsl_host_stop and bind the new function to host_stop.
Fixes: faf0b2e5af ("drivers/ata: add support to Freescale 3.0Gbps SATA Controller")
Cc: stable@vger.kernel.org
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 054aa8d439 upstream.
Jann Horn points out that there is another possible race wrt Unix domain
socket garbage collection, somewhat reminiscent of the one fixed in
commit cbcf01128d ("af_unix: fix garbage collect vs MSG_PEEK").
See the extended comment about the garbage collection requirements added
to unix_peek_fds() by that commit for details.
The race comes from how we can locklessly look up a file descriptor just
as it is in the process of being closed, and with the right artificial
timing (Jann added a few strategic 'mdelay(500)' calls to do that), the
Unix domain socket garbage collector could see the reference count
decrement of the close() happen before fget() took its reference to the
file and the file was attached onto a new file descriptor.
This is all (intentionally) correct on the 'struct file *' side, with
RCU lookups and lockless reference counting very much part of the
design. Getting that reference count out of order isn't a problem per
se.
But the garbage collector can get confused by seeing this situation of
having seen a file not having any remaining external references and then
seeing it being attached to an fd.
In commit cbcf01128d ("af_unix: fix garbage collect vs MSG_PEEK") the
fix was to serialize the file descriptor install with the garbage
collector by taking and releasing the unix_gc_lock.
That's not really an option here, but since this all happens when we are
in the process of looking up a file descriptor, we can instead simply
just re-check that the file hasn't been closed in the meantime, and just
re-do the lookup if we raced with a concurrent close() of the same file
descriptor.
Reported-and-tested-by: Jann Horn <jannh@google.com>
Acked-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52d04d4081 upstream.
When running without MIO support, with pci=nomio or for devices which
are not MIO-capable the zPCI subsystem generates pseudo-MMIO addresses
to allow access to PCI BARs via MMIO based Linux APIs even though the
platform uses function handles and BAR numbers.
This is done by stashing an index into our global IOMAP array which
contains the function handle in the 16 most significant bits of the
addresses returned by ioremap() always setting the most significant bit.
On the other hand the MIO addresses assigned by the platform for use,
while requiring special instructions, allow PCI access with virtually
mapped physical addresses. Now the problem is that these MIO addresses
and our own pseudo-MMIO addresses may overlap, while functionally this
would not be a problem by itself this overlap is detected by common code
as both address types are added as resources in the iomem_resource tree.
This leads to the overlapping resource claim of either the MIO capable
or non-MIO capable devices with being rejected.
Since PCI is tightly coupled to the use of the iomem_resource tree, see
for example the code for request_mem_region(), we can't reasonably get
rid of the overlap being detected by keeping our pseudo-MMIO addresses
out of the iomem_resource tree.
Instead let's move the range used by our own pseudo-MMIO addresses by
starting at (1UL << 62) and only using addresses below (1UL << 63) thus
avoiding the range currently used for MIO addresses.
Fixes: c7ff0e918a ("s390/pci: deal with devices that have no support for MIO instructions")
Cc: stable@vger.kernel.org # 5.3+
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c1b5a8466 upstream.
When I hot added a CPU, I found 'cpufreq' directory was not created
below /sys/devices/system/cpu/cpuX/.
It is because get_cpu_device() failed in add_cpu_dev_symlink().
cpufreq_add_dev() is the .add_dev callback of a CPU subsys interface.
It will be called when the CPU device registered into the system.
The call chain is as follows:
register_cpu()
->device_register()
->device_add()
->bus_probe_device()
->cpufreq_add_dev()
But only after the CPU device has been registered, we can get the
CPU device by get_cpu_device(), otherwise it will return NULL.
Since we already have the CPU device in cpufreq_add_dev(), pass
it to add_cpu_dev_symlink().
I noticed that the 'kobj' of the CPU device has been added into
the system before cpufreq_add_dev().
Fixes: 2f0ba790df ("cpufreq: Fix creation of symbolic links to policy directories")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d49eb91e8 upstream.
Currently when removing an ipmi_user the removal is deferred as a work on
the system's workqueue. Although this guarantees the free operation will
occur in non atomic context, it can race with the ipmi_msghandler module
removal (see [1]) . In case a remove_user work is scheduled for removal
and shortly after ipmi_msghandler module is removed we can end up in a
situation where the module is removed fist and when the work is executed
the system crashes with :
BUG: unable to handle page fault for address: ffffffffc05c3450
PF: supervisor instruction fetch in kernel mode
PF: error_code(0x0010) - not-present page
because the pages of the module are gone. In cleanup_ipmi() there is no
easy way to detect if there are any pending works to flush them before
removing the module. This patch creates a separate workqueue and schedules
the remove_work works on it. When removing the module the workqueue is
drained when destroyed to avoid the race.
[1] https://bugs.launchpad.net/bugs/1950666
Cc: stable@vger.kernel.org # 5.1
Fixes: 3b9a907223 (ipmi: fix sleep-in-atomic in free_user at cleanup SRCU user->release_barrier)
Signed-off-by: Ioanna Alifieraki <ioanna-maria.alifieraki@canonical.com>
Message-Id: <20211115131645.25116-1-ioanna-maria.alifieraki@canonical.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6bbfa44116 upstream.
The 'kprobe::data_size' is unsigned, thus it can not be negative. But if
user sets it enough big number (e.g. (size_t)-8), the result of 'data_size
+ sizeof(struct kretprobe_instance)' becomes smaller than sizeof(struct
kretprobe_instance) or zero. In result, the kretprobe_instance are
allocated without enough memory, and kretprobe accesses outside of
allocated memory.
To avoid this issue, introduce a max limitation of the
kretprobe::data_size. 4KB per instance should be OK.
Link: https://lkml.kernel.org/r/163836995040.432120.10322772773821182925.stgit@devnote2
Cc: stable@vger.kernel.org
Fixes: f47cd9b553 ("kprobes: kretprobe user entry-handler")
Reported-by: zhangyue <zhangyue1@kylinos.cn>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee201011c1 upstream.
IPCB/IP6CB need to be initialized when processing outbound v4 or v6 pkts
in the codepath of vrf device xmit function so that leftover garbage
doesn't cause futher code that uses the CB to incorrectly process the
pkt.
One occasion of the issue might occur when MPLS route uses the vrf
device as the outgoing device such as when the route is added using "ip
-f mpls route add <label> dev <vrf>" command.
The problems seems to exist since day one. Hence I put the day one
commits on the Fixes tags.
Fixes: 193125dbd8 ("net: Introduce VRF device driver")
Fixes: 35402e3136 ("net: Add IPv6 support to VRF device")
Cc: stable@vger.kernel.org
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20211130162637.3249-1-ssuryaextr@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7a61432dc8 ]
Possible recursive locking is detected by lockdep when SMC
falls back to TCP. The corresponding warnings are as follows:
============================================
WARNING: possible recursive locking detected
5.16.0-rc1+ #18 Tainted: G E
--------------------------------------------
wrk/1391 is trying to acquire lock:
ffff975246c8e7d8 (&ei->socket.wq.wait){..-.}-{3:3}, at: smc_switch_to_fallback+0x109/0x250 [smc]
but task is already holding lock:
ffff975246c8f918 (&ei->socket.wq.wait){..-.}-{3:3}, at: smc_switch_to_fallback+0xfe/0x250 [smc]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&ei->socket.wq.wait);
lock(&ei->socket.wq.wait);
*** DEADLOCK ***
May be due to missing lock nesting notation
2 locks held by wrk/1391:
#0: ffff975246040130 (sk_lock-AF_SMC){+.+.}-{0:0}, at: smc_connect+0x43/0x150 [smc]
#1: ffff975246c8f918 (&ei->socket.wq.wait){..-.}-{3:3}, at: smc_switch_to_fallback+0xfe/0x250 [smc]
stack backtrace:
Call Trace:
<TASK>
dump_stack_lvl+0x56/0x7b
__lock_acquire+0x951/0x11f0
lock_acquire+0x27a/0x320
? smc_switch_to_fallback+0x109/0x250 [smc]
? smc_switch_to_fallback+0xfe/0x250 [smc]
_raw_spin_lock_irq+0x3b/0x80
? smc_switch_to_fallback+0x109/0x250 [smc]
smc_switch_to_fallback+0x109/0x250 [smc]
smc_connect_fallback+0xe/0x30 [smc]
__smc_connect+0xcf/0x1090 [smc]
? mark_held_locks+0x61/0x80
? __local_bh_enable_ip+0x77/0xe0
? lockdep_hardirqs_on+0xbf/0x130
? smc_connect+0x12a/0x150 [smc]
smc_connect+0x12a/0x150 [smc]
__sys_connect+0x8a/0xc0
? syscall_enter_from_user_mode+0x20/0x70
__x64_sys_connect+0x16/0x20
do_syscall_64+0x34/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
The nested locking in smc_switch_to_fallback() is considered to
possibly cause a deadlock because smc_wait->lock and clc_wait->lock
are the same type of lock. But actually it is safe so far since
there is no other place trying to obtain smc_wait->lock when
clc_wait->lock is held. So the patch replaces spin_lock() with
spin_lock_nested() to avoid false report by lockdep.
Link: https://lkml.org/lkml/2021/11/19/962
Fixes: 2153bd1e3d ("Transfer remaining wait queue entries during fallback")
Reported-by: syzbot+e979d3597f48262cb4ee@syzkaller.appspotmail.com
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Acked-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0fa68da72c ]
The definition of macro MOTO_SROM_BUG is:
#define MOTO_SROM_BUG (lp->active == 8 && (get_unaligned_le32(
dev->dev_addr) & 0x00ffffff) == 0x3e0008)
and the if statement
if (MOTO_SROM_BUG) lp->active = 0;
using this macro indicates lp->active could be 8. If lp->active is 8 and
the second comparison of this macro is false. lp->active will remain 8 in:
lp->phy[lp->active].gep = (*p ? p : NULL); p += (2 * (*p) + 1);
lp->phy[lp->active].rst = (*p ? p : NULL); p += (2 * (*p) + 1);
lp->phy[lp->active].mc = get_unaligned_le16(p); p += 2;
lp->phy[lp->active].ana = get_unaligned_le16(p); p += 2;
lp->phy[lp->active].fdx = get_unaligned_le16(p); p += 2;
lp->phy[lp->active].ttm = get_unaligned_le16(p); p += 2;
lp->phy[lp->active].mci = *p;
However, the length of array lp->phy is 8, so array overflows can occur.
To fix these possible array overflows, we first check lp->active and then
return -EINVAL if it is greater or equal to ARRAY_SIZE(lp->phy) (i.e. 8).
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Teng Qi <starmiku1207184332@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61217be886 ]
In line 5001, if all id in the array 'lp->phy[8]' is not 0, when the
'for' end, the 'k' is 8.
At this time, the array 'lp->phy[8]' may be out of bound.
Signed-off-by: zhangyue <zhangyue1@kylinos.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f9c55c806 ]
The offset value is used in pointer math on skb->data.
Since ipv6_skip_exthdr may return -1 the pointer to uh and th
may not point to the actual udp and tcp headers and potentially
overwrite other stuff. This is why I think this should be checked.
EDIT: added {}'s, thanks Kees
Signed-off-by: Jordy Zomer <jordy@pwning.systems>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a66998e0fb ]
The if statement:
if (port >= DSAF_GE_NUM)
return;
limits the value of port less than DSAF_GE_NUM (i.e., 8).
However, if the value of port is 6 or 7, an array overflow could occur:
port_rst_off = dsaf_dev->mac_cb[port]->port_rst_off;
because the length of dsaf_dev->mac_cb is DSAF_MAX_PORT_NUM (i.e., 6).
To fix this possible array overflow, we first check port and if it is
greater than or equal to DSAF_MAX_PORT_NUM, the function returns.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Teng Qi <starmiku1207184332@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1527f69204 ]
AMD requires that the SATA controller be configured for devsleep in order
for S0i3 entry to work properly.
commit b1a9585cc3 ("ata: ahci: Enable DEVSLP by default on x86 with
SLP_S0") sets up a kernel policy to enable devsleep on Intel mobile
platforms that are using s0ix. Add the PCI ID for the SATA controller in
Green Sardine platforms to extend this policy by default for AMD based
systems using s0i3 as well.
Cc: Nehal-bakulchandra Shah <Nehal-bakulchandra.Shah@amd.com>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214091
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2cf49e00d4 ]
In SRIOV configuration, the reset may failed to bring asic back to normal but stop cpsch
already been called, the start_cpsch will not be called since there is no resume in this
case. When reset been triggered again, driver should avoid to do uninitialization again.
Signed-off-by: shaoyunl <shaoyun.liu@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0c2f8b670 ]
We can race where iscsi_session_recovery_timedout() has woken up the error
handler thread and it's now setting the devices to offline, and
session_recovery_timedout()'s call to scsi_target_unblock() is also trying
to set the device's state to transport-offline. We can then get a mix of
states.
For the case where we can't relogin we want the devices to be in
transport-offline so when we have repaired the connection
__iscsi_unblock_session() can set the state back to running.
Set the device state then call into libiscsi to wake up the error handler.
Link: https://lore.kernel.org/r/20211105221048.6541-2-michael.christie@oracle.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99b63316c3 ]
During the suspend is in process, thermal_zone_device_update bails out
thermal zone re-evaluation for any sensor trip violation without
setting next valid trip to that sensor. It assumes during resume
it will re-evaluate same thermal zone and update trip. But when it is
in suspend temperature goes down and on resume path while updating
thermal zone if temperature is less than previously violated trip,
thermal zone set trip function evaluates the same previous high and
previous low trip as new high and low trip. Since there is no change
in high/low trip, it bails out from thermal zone set trip API without
setting any trip. It leads to a case where sensor high trip or low
trip is disabled forever even though thermal zone has a valid high
or low trip.
During thermal zone device init, reset thermal zone previous high
and low trip. It resolves above mentioned scenario.
Signed-off-by: Manaf Meethalavalappu Pallikunhi <manafm@codeaurora.org>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a91cf0ffbc ]
When a disk has write caching disabled, we skip submission of a bio with
flush and sync requests before writing the superblock, since it's not
needed. However when the integrity checker is enabled, this results in
reports that there are metadata blocks referred by a superblock that
were not properly flushed. So don't skip the bio submission only when
the integrity checker is enabled for the sake of simplicity, since this
is a debug tool and not meant for use in non-debug builds.
fstests/btrfs/220 trigger a check-integrity warning like the following
when CONFIG_BTRFS_FS_CHECK_INTEGRITY=y and the disk with WCE=0.
btrfs: attempt to write superblock which references block M @5242880 (sdb2/5242880/0) which is not flushed out of disk's write cache (block flush_gen=1, dev->flush_gen=0)!
------------[ cut here ]------------
WARNING: CPU: 28 PID: 843680 at fs/btrfs/check-integrity.c:2196 btrfsic_process_written_superblock+0x22a/0x2a0 [btrfs]
CPU: 28 PID: 843680 Comm: umount Not tainted 5.15.0-0.rc5.39.el8.x86_64 #1
Hardware name: Dell Inc. Precision T7610/0NK70N, BIOS A18 09/11/2019
RIP: 0010:btrfsic_process_written_superblock+0x22a/0x2a0 [btrfs]
RSP: 0018:ffffb642afb47940 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000000000002 RCX: 0000000000000000
RDX: 00000000ffffffff RSI: ffff8b722fc97d00 RDI: ffff8b722fc97d00
RBP: ffff8b5601c00000 R08: 0000000000000000 R09: c0000000ffff7fff
R10: 0000000000000001 R11: ffffb642afb476f8 R12: ffffffffffffffff
R13: ffffb642afb47974 R14: ffff8b5499254c00 R15: 0000000000000003
FS: 00007f00a06d4080(0000) GS:ffff8b722fc80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fff5cff5ff0 CR3: 00000001c0c2a006 CR4: 00000000001706e0
Call Trace:
btrfsic_process_written_block+0x2f7/0x850 [btrfs]
__btrfsic_submit_bio.part.19+0x310/0x330 [btrfs]
? bio_associate_blkg_from_css+0xa4/0x2c0
btrfsic_submit_bio+0x18/0x30 [btrfs]
write_dev_supers+0x81/0x2a0 [btrfs]
? find_get_pages_range_tag+0x219/0x280
? pagevec_lookup_range_tag+0x24/0x30
? __filemap_fdatawait_range+0x6d/0xf0
? __raw_callee_save___native_queued_spin_unlock+0x11/0x1e
? find_first_extent_bit+0x9b/0x160 [btrfs]
? __raw_callee_save___native_queued_spin_unlock+0x11/0x1e
write_all_supers+0x1b3/0xa70 [btrfs]
? __raw_callee_save___native_queued_spin_unlock+0x11/0x1e
btrfs_commit_transaction+0x59d/0xac0 [btrfs]
close_ctree+0x11d/0x339 [btrfs]
generic_shutdown_super+0x71/0x110
kill_anon_super+0x14/0x30
btrfs_kill_super+0x12/0x20 [btrfs]
deactivate_locked_super+0x31/0x70
cleanup_mnt+0xb8/0x140
task_work_run+0x6d/0xb0
exit_to_user_mode_prepare+0x1f0/0x200
syscall_exit_to_user_mode+0x12/0x30
do_syscall_64+0x46/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f009f711dfb
RSP: 002b:00007fff5cff7928 EFLAGS: 00000246 ORIG_RAX: 00000000000000a6
RAX: 0000000000000000 RBX: 000055b68c6c9970 RCX: 00007f009f711dfb
RDX: 0000000000000001 RSI: 0000000000000000 RDI: 000055b68c6c9b50
RBP: 0000000000000000 R08: 000055b68c6ca900 R09: 00007f009f795580
R10: 0000000000000000 R11: 0000000000000246 R12: 000055b68c6c9b50
R13: 00007f00a04bf184 R14: 0000000000000000 R15: 00000000ffffffff
---[ end trace 2c4b82abcef9eec4 ]---
S-65536(sdb2/65536/1)
-->
M-1064960(sdb2/1064960/1)
Reviewed-by: Filipe Manana <fdmanana@gmail.com>
Signed-off-by: Wang Yugui <wangyugui@e16-tech.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5dbc4cb466 ]
There is a difference in how architectures treat "mem=" option. For some
that is an amount of online memory, for s390 and x86 this is the limiting
max address. Some memblock api like memblock_enforce_memory_limit()
take limit argument and explicitly treat it as the size of online memory,
and use __find_max_addr to convert it to an actual max address. Current
s390 usage:
memblock_enforce_memory_limit(memblock_end_of_DRAM());
yields different results depending on presence of memory holes (offline
memory blocks in between online memory). If there are no memory holes
limit == max_addr in memblock_enforce_memory_limit() and it does trim
online memory and reserved memory regions. With memory holes present it
actually does nothing.
Since we already use memblock_remove() explicitly to trim online memory
regions to potential limit (think mem=, kdump, addressing limits, etc.)
drop the usage of memblock_enforce_memory_limit() altogether. Trimming
reserved regions should not be required, since we now use
memblock_set_current_limit() to limit allocations and any explicit memory
reservations above the limit is an actual problem we should not hide.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39f5329218 ]
When WWAN device wake from S3 deep, under thinkpad platform,
WWAN would be disabled. This disable status could be checked
by command 'nmcli r wwan' or 'rfkill list'.
Issue analysis as below:
When host resume from S3 deep, thinkpad_acpi driver would
call hotkey_resume() function. Finnaly, it will use
wan_get_status to check the current status of WWAN device.
During this resume progress, wan_get_status would always
return off even WWAN boot up completely.
In patch V2, Hans said 'sw_state should be unchanged
after a suspend/resume. It's better to drop the
tpacpi_rfk_update_swstate call all together from the
resume path'.
And it's confimed by Lenovo that GWAN is no longer
available from WHL generation because the design does not
match with current pin control.
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Link: https://lore.kernel.org/r/20211108060648.8212-1-slark_xiao@163.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6def480181 ]
When kmemdup called failed and register_net_sysctl return NULL, should
return ENOMEM instead of ENOBUFS
Signed-off-by: liuguoqiang <liuguoqiang@uniontech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b922f62259 ]
This bug report shows up when running our research tools. The
reports is SOOB read, but it seems SOOB write is also possible
a few lines below.
In details, fw.len and sw.len are inputs coming from io. A len
over the size of self->rpc triggers SOOB. The patch fixes the
bugs by adding sanity checks.
The bugs are triggerable with compromised/malfunctioning devices.
They are potentially exploitable given they first leak up to
0xffff bytes and able to overwrite the region later.
The patch is tested with QEMU emulater.
This is NOT tested with a real device.
Attached is the log we found by fuzzing.
BUG: KASAN: slab-out-of-bounds in
hw_atl_utils_fw_upload_dwords+0x393/0x3c0 [atlantic]
Read of size 4 at addr ffff888016260b08 by task modprobe/213
CPU: 0 PID: 213 Comm: modprobe Not tainted 5.6.0 #1
Call Trace:
dump_stack+0x76/0xa0
print_address_description.constprop.0+0x16/0x200
? hw_atl_utils_fw_upload_dwords+0x393/0x3c0 [atlantic]
? hw_atl_utils_fw_upload_dwords+0x393/0x3c0 [atlantic]
__kasan_report.cold+0x37/0x7c
? aq_hw_read_reg_bit+0x60/0x70 [atlantic]
? hw_atl_utils_fw_upload_dwords+0x393/0x3c0 [atlantic]
kasan_report+0xe/0x20
hw_atl_utils_fw_upload_dwords+0x393/0x3c0 [atlantic]
hw_atl_utils_fw_rpc_call+0x95/0x130 [atlantic]
hw_atl_utils_fw_rpc_wait+0x176/0x210 [atlantic]
hw_atl_utils_mpi_create+0x229/0x2e0 [atlantic]
? hw_atl_utils_fw_rpc_wait+0x210/0x210 [atlantic]
? hw_atl_utils_initfw+0x9f/0x1c8 [atlantic]
hw_atl_utils_initfw+0x12a/0x1c8 [atlantic]
aq_nic_ndev_register+0x88/0x650 [atlantic]
? aq_nic_ndev_init+0x235/0x3c0 [atlantic]
aq_pci_probe+0x731/0x9b0 [atlantic]
? aq_pci_func_init+0xc0/0xc0 [atlantic]
local_pci_probe+0xd3/0x160
pci_device_probe+0x23f/0x3e0
Reported-by: Brendan Dolan-Gavitt <brendandg@nyu.edu>
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2153bd1e3d ]
The SMC fallback is incomplete currently. There may be some
wait queue entries remaining in smc socket->wq, which should
be removed to clcsocket->wq during the fallback.
For example, in nginx/wrk benchmark, this issue causes an
all-zeros test result:
server: nginx -g 'daemon off;'
client: smc_run wrk -c 1 -t 1 -d 5 http://11.200.15.93/index.html
Running 5s test @ http://11.200.15.93/index.html
1 threads and 1 connections
Thread Stats Avg Stdev Max ± Stdev
Latency 0.00us 0.00us 0.00us -nan%
Req/Sec 0.00 0.00 0.00 -nan%
0 requests in 5.00s, 0.00B read
Requests/sec: 0.00
Transfer/sec: 0.00B
The reason for this all-zeros result is that when wrk used SMC
to replace TCP, it added an eppoll_entry into smc socket->wq
and expected to be notified if epoll events like EPOLL_IN/
EPOLL_OUT occurred on the smc socket.
However, once a fallback occurred, wrk switches to use clcsocket.
Now it is clcsocket->wq instead of smc socket->wq which will
be woken up. The eppoll_entry remaining in smc socket->wq does
not work anymore and wrk stops the test.
This patch fixes this issue by removing remaining wait queue
entries from smc socket->wq to clcsocket->wq during the fallback.
Link: https://www.spinics.net/lists/netdev/msg779769.html
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb162bb2b4 ]
When PHY_SUN6I_MIPI_DPHY is selected, and RESET_CONTROLLER
is not selected, Kbuild gives the following warning:
WARNING: unmet direct dependencies detected for PHY_SUN6I_MIPI_DPHY
Depends on [n]: (ARCH_SUNXI [=n] || COMPILE_TEST [=y]) && HAS_IOMEM [=y] && COMMON_CLK [=y] && RESET_CONTROLLER [=n]
Selected by [y]:
- DRM_SUN6I_DSI [=y] && HAS_IOMEM [=y] && DRM_SUN4I [=y]
This is because DRM_SUN6I_DSI selects PHY_SUN6I_MIPI_DPHY
without selecting or depending on RESET_CONTROLLER, despite
PHY_SUN6I_MIPI_DPHY depending on RESET_CONTROLLER.
These unmet dependency bugs were detected by Kismet,
a static analysis tool for Kconfig. Please advise if this
is not the appropriate solution.
v2:
Fixed indentation to match the rest of the file.
Signed-off-by: Julian Braha <julianbraha@gmail.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20211109032351.43322-1-julianbraha@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3506eee81 ]
Fix the length of holes reported at the end of a file: the length is
relative to the beginning of the extent, not the seek position which is
rounded down to the filesystem block size.
This bug went unnoticed for some time, but is now caught by the
following assertion in iomap_iter_done():
WARN_ON_ONCE(iter->iomap.offset + iter->iomap.length <= iter->pos)
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49462e2be1 ]
Before this patch, evict would clear the iopen glock's gl_object after
releasing the inode glock. In the meantime, another process could reuse
the same block and thus glocks for a new inode. It would lock the inode
glock (exclusively), and then the iopen glock (shared). The shared
locking mode doesn't provide any ordering against the evict, so by the
time the iopen glock is reused, evict may not have gotten to setting
gl_object to NULL.
Fix that by releasing the iopen glock before the inode glock in
gfs2_evict_inode.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>gl_object
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9b91b6b019 upstream.
There's possibility of an ABBA deadlock in case of a splice write to an
overlayfs file and a concurrent splice write to a corresponding real file.
The call chain for splice to an overlay file:
-> do_splice [takes sb_writers on overlay file]
-> do_splice_from
-> iter_file_splice_write [takes pipe->mutex]
-> vfs_iter_write
...
-> ovl_write_iter [takes sb_writers on real file]
And the call chain for splice to a real file:
-> do_splice [takes sb_writers on real file]
-> do_splice_from
-> iter_file_splice_write [takes pipe->mutex]
Syzbot successfully bisected this to commit 82a763e61e ("ovl: simplify
file splice").
Fix by reverting the write part of the above commit and by adding missing
bits from ovl_write_iter() into ovl_splice_write().
Fixes: 82a763e61e ("ovl: simplify file splice")
Reported-and-tested-by: syzbot+579885d1a9a833336209@syzkaller.appspotmail.com
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Cc: Stan Hu <stanhu@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 82a763e61e upstream.
generic_file_splice_read() and iter_file_splice_write() will call back into
f_op->iter_read() and f_op->iter_write() respectively. These already do
the real file lookup and cred override. So the code in ovl_splice_read()
and ovl_splice_write() is redundant.
In addition the ovl_file_accessed() call in ovl_splice_write() is
incorrect, though probably harmless.
Fix by calling generic_file_splice_read() and iter_file_splice_write()
directly.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Cc: Stan Hu <stanhu@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f015d89a4 upstream.
The mechanism in use to allow the client to see the results of COPY/CLONE
is to drop those pages from the pagecache. This forces the client to read
those pages once more from the server. However, truncate_pagecache_range()
zeros out partial pages instead of dropping them. Let us instead use
invalidate_inode_pages2_range() with full-page offsets to ensure the client
properly sees the results of COPY/CLONE operations.
Cc: <stable@vger.kernel.org> # v4.7+
Fixes: 2e72448b07 ("NFS: Add COPY nfs operation")
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-12-08 09:03:17 +01:00
661 changed files with 8678 additions and 3384 deletions
This repository contains the Linux kernel used on the Raspberry Pi. If you believe that the issue you are seeing is kernel-related, this is the right place. If not, we have other repositories for the GPU firmware at [github.com/raspberrypi/firmware](https://github.com/raspberrypi/firmware) and Raspberry Pi userland applications at [github.com/raspberrypi/userland](https://github.com/raspberrypi/userland). If you have problems with the Raspbian distribution packages, report them in the [github.com/RPi-Distro/repo](https://github.com/RPi-Distro/repo). If you simply have a question, then [the Raspberry Pi forums](https://www.raspberrypi.org/forums) are the best place to ask it.
**Describe the bug**
Add a clear and concise description of what you think the bug is.
**To reproduce**
List the steps required to reproduce the issue.
**Expected behaviour**
Add a clear and concise description of what you expected to happen.
**Actual behaviour**
Add a clear and concise description of what actually happened.
**System**
Copy and paste the results of the raspinfo command in to this section. Alternatively, copy and paste a pastebin link, or add answers to the following questions:
* Which model of Raspberry Pi? e.g. Pi3B+, PiZeroW
* Which OS and version (`cat /etc/rpi-issue`)?
* Which firmware version (`vcgencmd version`)?
* Which kernel version (`uname -a`)?
**Logs**
If applicable, add the relevant output from `dmesg` or similar.
description:Create a report to help us fix your issue
body:
- type:markdown
attributes:
value:|
**Is this the right place for my bug report?**
This repository contains the Linux kernel used on the Raspberry Pi.
If you believe that the issue you are seeing is kernel-related, this is the right place.
If not, we have other repositories for the GPU firmware at [github.com/raspberrypi/firmware](https://github.com/raspberrypi/firmware) and Raspberry Pi userland applications at [github.com/raspberrypi/userland](https://github.com/raspberrypi/userland).
If you have problems with the Raspbian distribution packages, report them in the [github.com/RPi-Distro/repo](https://github.com/RPi-Distro/repo).
If you simply have a question, then [the Raspberry Pi forums](https://www.raspberrypi.org/forums) are the best place to ask it.
- type:textarea
id:description
attributes:
label:Describe the bug
description:|
Add a clear and concise description of what you think the bug is.
validations:
required:true
- type:textarea
id:reproduce
attributes:
label:Steps to reproduce the behaviour
description:|
List the steps required to reproduce the issue.
validations:
required:true
- type:dropdown
id:model
attributes:
label:Device (s)
description:Onwhich device you are facing the bug?
multiple:true
options:
- Raspberry Pi Zero
- Raspberry Pi Zero W/WH
- Raspberry Pi Zero 2 W
- Raspberry Pi 1 Mod. A
- Raspberry Pi 1 Mod. A+
- Raspberry Pi 1 Mod. B
- Raspberry Pi 1 Mod. B+
- Raspberry Pi 2 Mod. B
- Raspberry Pi 2 Mod. B v1.2
- Raspberry Pi 3 Mod. A+
- Raspberry Pi 3 Mod. B
- Raspberry Pi 3 Mod. B+
- Raspberry Pi 4 Mod. B
- Raspberry Pi 400
- Raspberry Pi CM1
- Raspberry Pi CM3
- Raspberry Pi CM3 Lite
- Raspberry Pi CM3+
- Raspberry Pi CM3+ Lite
- Raspberry Pi CM4
- Raspberry Pi CM4 Lite
- Other
validations:
required:true
- type:textarea
id:system
attributes:
label:System
description:|
Copy and paste the results of the raspinfo command in to this section.
Alternatively, copy and paste a pastebin link, or add answers to the following questions:
* Which OS and version (`cat /etc/rpi-issue`)?
* Which firmware version (`vcgencmd version`)?
* Which kernel version (`uname -a`)?
validations:
required:true
- type:textarea
id:logs
attributes:
label:Logs
description:|
If applicable, add the relevant output from `dmesg` or similar.
about:"Please do not use GitHub for asking questions. If you simply have a question, then the Raspberry Pi forums are the best place to ask it. Thanks in advance for helping us keep the issue tracker clean!"
- name:"⛔ Problems with the Raspbian distribution packages"
url:https://github.com/RPi-Distro/repo
about:"If you have problems with the Raspbian distribution packages, please report them in the github.com/RPi-Distro/repo."
This enables the kernel to use EFI runtime services that are
available (such as the EFI variable services).
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
