See: https://forum.libreelec.tv/thread/24783-tv-avr-turns-back-on-right-after-turning-them-off
While the kernel provides a :D flag for assuming device is connected,
it doesn't stop this function from being called and generating a cec_phys_addr_invalidate
message when hotplug is deasserted.
That message provokes a flurry of CEC messages which for many users results in the TV
switching back on again and it's very hard to get it to stay switched off.
It seems to only occur with an AVR and TV connected but has been observed across a
number of manufacturers.
The issue started with https://github.com/raspberrypi/linux/pull/4371
and this provides an optional way of getting back the old behaviour
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
See: https://forum.libreelec.tv/thread/25427-le-10-0-2-on-rpi4-not-playing-files-that-10-0-1-had-no-problems-with/
The issue is that kodi changes hdmi mode to 3840x2160@24 initially with "max bcp=8"
After decoding the first frame it changes property to "max bpc=12".
Now vc4_hdmi_encoder_compute_config chooses vc4_state->output_bpc = 12 with output_format=VC4_HDMI_OUTPUT_RGB
This requires scrambling as clock > 300MHz (and we have hdmi_enable_4kp60=1).
vc4_hdmi_encoder_atomic_mode_set (without this PR's assignment to mode_changed) is currenly not called so we don't assign:
vc4_hdmi->output_bpc = vc4_state->output_bpc
which means vc4_hdmi_enable_scrambling never enables scrambling (as vc4_hdmi->output_bpc is still 8).
But we do set the pixel clock in phy_init() to a clock frequency that requires scrambling.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
The HVS always composes in the RGB domain, but there is a colourspace
conversion block on the output to allow for sending YCbCr over the
HDMI interface.
The colourspace on that link is configurable via the "Colorspace"
property on the connector, and that updates the infoframes. There
is also selection of limited or full range based on the mode selected
or an override.
Add code to update the CSC as well so that the metadata matches the
image data.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
commit 031495635b upstream.
The following patches resulted in deferring crash kernel reservation to
mem_init(), mainly aimed at platforms with DMA memory zones (no IOMMU),
in particular Raspberry Pi 4.
commit 1a8e1cef76 ("arm64: use both ZONE_DMA and ZONE_DMA32")
commit 8424ecdde7 ("arm64: mm: Set ZONE_DMA size based on devicetree's dma-ranges")
commit 0a30c53573 ("arm64: mm: Move reserve_crashkernel() into mem_init()")
commit 2687275a58 ("arm64: Force NO_BLOCK_MAPPINGS if crashkernel reservation is required")
Above changes introduced boot slowdown due to linear map creation for
all the memory banks with NO_BLOCK_MAPPINGS, see discussion[1]. The proposed
changes restore crash kernel reservation to earlier behavior thus avoids
slow boot, particularly for platforms with IOMMU (no DMA memory zones).
Tested changes to confirm no ~150ms boot slowdown on our SoC with IOMMU
and 8GB memory. Also tested with ZONE_DMA and/or ZONE_DMA32 configs to confirm
no regression to deferring scheme of crash kernel memory reservation.
In both cases successfully collected kernel crash dump.
[1] https://lore.kernel.org/all/9436d033-579b-55fa-9b00-6f4b661c2dd7@linux.microsoft.com/
Signed-off-by: Vijay Balakrishna <vijayb@linux.microsoft.com>
Cc: stable@vger.kernel.org
Reviewed-by: Pasha Tatashin <pasha.tatashin@soleen.com>
Link: https://lore.kernel.org/r/1646242689-20744-1-git-send-email-vijayb@linux.microsoft.com
[will: Add #ifdef CONFIG_KEXEC_CORE guards to fix 'crashk_res' references in allnoconfig build]
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 390031c942 upstream.
Matthew Wilcox reported that there is a missing mmap_lock in
file_files_note that could possibly lead to a user after free.
Solve this by using the existing vma snapshot for consistency
and to avoid the need to take the mmap_lock anywhere in the
coredump code except for dump_vma_snapshot.
Update the dump_vma_snapshot to capture vm_pgoff and vm_file
that are neeeded by fill_files_note.
Add free_vma_snapshot to free the captured values of vm_file.
Reported-by: Matthew Wilcox <willy@infradead.org>
Link: https://lkml.kernel.org/r/20220131153740.2396974-1-willy@infradead.org
Cc: stable@vger.kernel.org
Fixes: a07279c9a8 ("binfmt_elf, binfmt_elf_fdpic: use a VMA list snapshot")
Fixes: 2aa362c49c ("coredump: extend core dump note section to contain file names of mapped files")
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ec7d32307 upstream.
Instead of individually passing cprm->siginfo and cprm->regs
into fill_note_info pass all of struct coredump_params.
This is preparation to allow fill_files_note to use the existing
vma snapshot.
Reviewed-by: Jann Horn <jannh@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 49c1866348 upstream.
The condition is impossible and to the best of my knowledge has never
triggered.
We are in deep trouble if that conditions happens and we walk past
the end of our allocated array.
So delete the WARN_ON and the code that makes it look like the kernel
can handle the case of walking past the end of it's vma_meta array.
Reviewed-by: Jann Horn <jannh@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95c5436a48 upstream.
Move the call of dump_vma_snapshot and kvfree(vma_meta) out of the
individual coredump routines into do_coredump itself. This makes
the code less error prone and easier to maintain.
Make the vma snapshot available to the coredump routines
in struct coredump_params. This makes it easier to
change and update what is captures in the vma snapshot
and will be needed for fixing fill_file_notes.
Reviewed-by: Jann Horn <jannh@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a8859f373 upstream.
FNAME(cmpxchg_gpte) is an inefficient mess. It is at least decent if it
can go through get_user_pages_fast(), but if it cannot then it tries to
use memremap(); that is not just terribly slow, it is also wrong because
it assumes that the VM_PFNMAP VMA is contiguous.
The right way to do it would be to do the same thing as
hva_to_pfn_remapped() does since commit add6a0cd1c ("KVM: MMU: try to
fix up page faults before giving up", 2016-07-05), using follow_pte()
and fixup_user_fault() to determine the correct address to use for
memremap(). To do this, one could for example extract hva_to_pfn()
for use outside virt/kvm/kvm_main.c. But really there is no reason to
do that either, because there is already a perfectly valid address to
do the cmpxchg() on, only it is a userspace address. That means doing
user_access_begin()/user_access_end() and writing the code in assembly
to handle exceptions correctly. Worse, the guest PTE can be 8-byte
even on i686 so there is the extra complication of using cmpxchg8b to
account for. But at least it is an efficient mess.
(Thanks to Linus for suggesting improvement on the inline assembly).
Reported-by: Qiuhao Li <qiuhao@sysec.org>
Reported-by: Gaoning Pan <pgn@zju.edu.cn>
Reported-by: Yongkang Jia <kangel@zju.edu.cn>
Reported-by: syzbot+6cde2282daa792c49ab8@syzkaller.appspotmail.com
Debugged-by: Tadeusz Struk <tadeusz.struk@linaro.org>
Tested-by: Maxim Levitsky <mlevitsk@redhat.com>
Cc: stable@vger.kernel.org
Fixes: bd53cb35a3 ("X86/KVM: Handle PFNs outside of kernel reach when touching GPTEs")
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f19c44452b upstream.
IPv6 nd target mask was not getting populated in flow dump.
In the function __ovs_nla_put_key the icmp code mask field was checked
instead of icmp code key field to classify the flow as neighbour discovery.
ufid:bdfbe3e5-60c2-43b0-a5ff-dfcac1c37328, recirc_id(0),dp_hash(0/0),
skb_priority(0/0),in_port(ovs-nm1),skb_mark(0/0),ct_state(0/0),
ct_zone(0/0),ct_mark(0/0),ct_label(0/0),
eth(src=00:00:00:00:00:00/00:00:00:00:00:00,
dst=00:00:00:00:00:00/00:00:00:00:00:00),
eth_type(0x86dd),
ipv6(src=::/::,dst=::/::,label=0/0,proto=58,tclass=0/0,hlimit=0/0,frag=no),
icmpv6(type=135,code=0),
nd(target=2001::2/::,
sll=00:00:00:00:00:00/00:00:00:00:00:00,
tll=00:00:00:00:00:00/00:00:00:00:00:00),
packets:10, bytes:860, used:0.504s, dp:ovs, actions:ovs-nm2
Fixes: e64457191a (openvswitch: Restructure datapath.c and flow.c)
Signed-off-by: Martin Varghese <martin.varghese@nokia.com>
Link: https://lore.kernel.org/r/20220328054148.3057-1-martinvarghesenokia@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a3a6a2a03 upstream.
Moving to an EPOLL based IRQ controller broke uml_mconsole stop/go
commands. This fixes it and restores stop/go functionality.
Fixes: ff6a17989c ("Epoll based IRQ controller")
Signed-off-by: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c3c07fc25f upstream.
Abort fastmap scanning and return error code if memory allocation fails
in add_aeb(). Otherwise ubi will get wrong peb statistics information
after scanning.
Fixes: dbb7d2a88d ("UBI: Add fastmap core")
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee2a098851 upstream.
Let's say that the caller has storage for num_elem stack frames. Then,
the BPF stack helper functions walk the stack for only num_elem frames.
This means that if skip > 0, one keeps only 'num_elem - skip' frames.
This is because it sets init_nr in the perf_callchain_entry to the end
of the buffer to save num_elem entries only. I believe it was because
the perf callchain code unwound the stack frames until it reached the
global max size (sysctl_perf_event_max_stack).
However it now has perf_callchain_entry_ctx.max_stack to limit the
iteration locally. This simplifies the code to handle init_nr in the
BPF callstack entries and removes the confusion with the perf_event's
__PERF_SAMPLE_CALLCHAIN_EARLY which sets init_nr to 0.
Also change the comment on bpf_get_stack() in the header file to be
more explicit what the return value means.
Fixes: c195651e56 ("bpf: add bpf_get_stack helper")
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/30a7b5d5-6726-1cc2-eaee-8da2828a9a9c@oracle.com
Link: https://lore.kernel.org/bpf/20220314182042.71025-1-namhyung@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based-on-patch-by: Eugene Loh <eugene.loh@oracle.com>
commit 05fe3c103f upstream.
__setup() handlers should return 1 if the command line option is handled
and 0 if not (or maybe never return 0; it just pollutes init's
environment). This prevents:
Unknown kernel command line parameters \
"BOOT_IMAGE=/boot/bzImage-517rc5 hardened_usercopy=off", will be \
passed to user space.
Run /sbin/init as init process
with arguments:
/sbin/init
with environment:
HOME=/
TERM=linux
BOOT_IMAGE=/boot/bzImage-517rc5
hardened_usercopy=off
or
hardened_usercopy=on
but when "hardened_usercopy=foo" is used, there is no Unknown kernel
command line parameter.
Return 1 to indicate that the boot option has been handled.
Print a warning if strtobool() returns an error on the option string,
but do not mark this as in unknown command line option and do not cause
init's environment to be polluted with this string.
Link: https://lkml.kernel.org/r/20220222034249.14795-1-rdunlap@infradead.org
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru
Fixes: b5cb15d937 ("usercopy: Allow boot cmdline disabling of hardening")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru>
Acked-by: Chris von Recklinghausen <crecklin@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 460a79e188 upstream.
__setup() handlers should return 1 if the command line option is handled
and 0 if not (or maybe never return 0; it just pollutes init's
environment).
The only reason that this particular __setup handler does not pollute
init's environment is that the setup string contains a '.', as in
"cgroup.memory". This causes init/main.c::unknown_boottoption() to
consider it to be an "Unused module parameter" and ignore it. (This is
for parsing of loadable module parameters any time after kernel init.)
Otherwise the string "cgroup.memory=whatever" would be added to init's
environment strings.
Instead of relying on this '.' quirk, just return 1 to indicate that the
boot option has been handled.
Note that there is no warning message if someone enters:
cgroup.memory=anything_invalid
Link: https://lkml.kernel.org/r/20220222005811.10672-1-rdunlap@infradead.org
Fixes: f7e1cb6ec5 ("mm: memcontrol: account socket memory in unified hierarchy memory controller")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru>
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru
Reviewed-by: Michal Koutný <mkoutny@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: Roman Gushchin <roman.gushchin@linux.dev>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e6d0949369 upstream.
__setup() handlers should return 1 if the command line option is handled
and 0 if not (or maybe never return 0; it just pollutes init's
environment). This prevents:
Unknown kernel command line parameters \
"BOOT_IMAGE=/boot/bzImage-517rc5 stack_guard_gap=100", will be \
passed to user space.
Run /sbin/init as init process
with arguments:
/sbin/init
with environment:
HOME=/
TERM=linux
BOOT_IMAGE=/boot/bzImage-517rc5
stack_guard_gap=100
Return 1 to indicate that the boot option has been handled.
Note that there is no warning message if someone enters:
stack_guard_gap=anything_invalid
and 'val' and stack_guard_gap are both set to 0 due to the use of
simple_strtoul(). This could be improved by using kstrtoxxx() and
checking for an error.
It appears that having stack_guard_gap == 0 is valid (if unexpected) since
using "stack_guard_gap=0" on the kernel command line does that.
Link: https://lkml.kernel.org/r/20220222005817.11087-1-rdunlap@infradead.org
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru
Fixes: 1be7107fbe ("mm: larger stack guard gap, between vmas")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6340dcbd61 upstream.
The commit b37a466837 ("netdevice: add the case if dev is NULL") changed
the way how the NULL check for net_devices have to be handled when trying
to reduce its reference counter. Before this commit, it was the
responsibility of the caller to check whether the object is NULL or not.
But it was changed to behave more like kfree. Now the callee has to handle
the NULL-case.
The batman-adv code was scanned via cocinelle for similar places. These
were changed to use the paradigm
@@
identifier E, T, R, C;
identifier put;
@@
void put(struct T *E)
{
+ if (!E)
+ return;
kref_put(&E->C, R);
}
Functions which were used in other sources files were moved to the header
to allow the compiler to inline the NULL check and the kref_put call.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ffebd90532 upstream.
The Type C ACPI device on older Chromebooks is not generated correctly
(since their EC firmware doesn't support the new commands required). In
such cases, the crafted ACPI device doesn't have an EC parent, and it is
therefore not useful (it shouldn't be generated in the first place since
the EC firmware doesn't support any of the Type C commands).
To handle devices which use these older firmware revisions, check for
the parent EC device handle, and fail the probe if it's not found.
Fixes: fdc6b21e24 ("platform/chrome: Add Type C connector class driver")
Reported-by: Alyssa Ross <hi@alyssa.is>
Reviewed-by: Tzung-Bi Shih <tzungbi@google.com>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Alyssa Ross <hi@alyssa.is>
Tested-by: Alyssa Ross <hi@alyssa.is>
Link: https://lore.kernel.org/r/20220126190219.3095419-1-pmalani@chromium.org
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d67412f24 upstream.
iop32x is one of the last platforms to use IRQ 0, and this has apparently
stopped working in a 2014 cleanup without anyone noticing. This interrupt
is used for the DMA engine, so most likely this has not actually worked
in the past 7 years, but it's also not essential for using this board.
I'm splitting out this change from my GENERIC_IRQ_MULTI_HANDLER
conversion so it can be backported if anyone cares.
Fixes: a71b092a9c ("ARM: Convert handle_IRQ to use __handle_domain_irq")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[ardb: take +1 offset into account in mask/unmask and init as well]
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com> # ARMv7M
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3cbf0e392f upstream.
Hulk Robot reported a KASAN report about use-after-free:
==================================================================
BUG: KASAN: use-after-free in __list_del_entry_valid+0x13d/0x160
Read of size 8 at addr ffff888035e37d98 by task ubiattach/1385
[...]
Call Trace:
klist_dec_and_del+0xa7/0x4a0
klist_put+0xc7/0x1a0
device_del+0x4d4/0xed0
cdev_device_del+0x1a/0x80
ubi_attach_mtd_dev+0x2951/0x34b0 [ubi]
ctrl_cdev_ioctl+0x286/0x2f0 [ubi]
Allocated by task 1414:
device_add+0x60a/0x18b0
cdev_device_add+0x103/0x170
ubi_create_volume+0x1118/0x1a10 [ubi]
ubi_cdev_ioctl+0xb7f/0x1ba0 [ubi]
Freed by task 1385:
cdev_device_del+0x1a/0x80
ubi_remove_volume+0x438/0x6c0 [ubi]
ubi_cdev_ioctl+0xbf4/0x1ba0 [ubi]
[...]
==================================================================
The lock held by ctrl_cdev_ioctl is ubi_devices_mutex, but the lock held
by ubi_cdev_ioctl is ubi->device_mutex. Therefore, the two locks can be
concurrent.
ctrl_cdev_ioctl contains two operations: ubi_attach and ubi_detach.
ubi_detach is bug-free because it uses reference counting to prevent
concurrency. However, uif_init and uif_close in ubi_attach may race with
ubi_cdev_ioctl.
uif_init will race with ubi_cdev_ioctl as in the following stack.
cpu1 cpu2 cpu3
_______________________|________________________|______________________
ctrl_cdev_ioctl
ubi_attach_mtd_dev
uif_init
ubi_cdev_ioctl
ubi_create_volume
cdev_device_add
ubi_add_volume
// sysfs exist
kill_volumes
ubi_cdev_ioctl
ubi_remove_volume
cdev_device_del
// first free
ubi_free_volume
cdev_del
// double free
cdev_device_del
And uif_close will race with ubi_cdev_ioctl as in the following stack.
cpu1 cpu2 cpu3
_______________________|________________________|______________________
ctrl_cdev_ioctl
ubi_attach_mtd_dev
uif_init
ubi_cdev_ioctl
ubi_create_volume
cdev_device_add
ubi_debugfs_init_dev
//error goto out_uif;
uif_close
kill_volumes
ubi_cdev_ioctl
ubi_remove_volume
cdev_device_del
// first free
ubi_free_volume
// double free
The cause of this problem is that commit 714fb87e8b make device
"available" before it becomes accessible via sysfs. Therefore, we
roll back the modification. We will fix the race condition between
ubi device creation and udev by removing ubi_get_device in
vol_attribute_show and dev_attribute_show.This avoids accessing
uninitialized ubi_devices[ubi_num].
ubi_get_device is used to prevent devices from being deleted during
sysfs execution. However, now kernfs ensures that devices will not
be deleted before all reference counting are released.
The key process is shown in the following stack.
device_del
device_remove_attrs
device_remove_groups
sysfs_remove_groups
sysfs_remove_group
remove_files
kernfs_remove_by_name
kernfs_remove_by_name_ns
__kernfs_remove
kernfs_drain
Fixes: 714fb87e8b ("ubi: Fix race condition between ubi device creation and udev")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8bd296cca upstream.
The algorithm __cbc-aes-neonbs requires a fallback so we need
to select the config options for them or otherwise it will fail
to register on boot-up.
Fixes: 00b99ad2ba ("crypto: arm/aes-neonbs - Use generic cbc...")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 892cb524ae upstream.
Since IRQF_NO_SUSPEND used for imx mailbox driver, that means this irq
can't be used for wakeup source so that can't wakeup from freeze mode.
Add pm_system_wakeup() to wakeup from freeze mode.
Fixes: b7b2796b9b31e("mailbox: imx: ONLY IPC MU needs IRQF_NO_SUSPEND flag")
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a7f62f919 upstream.
The rxrpc_call struct has a timer used to handle various timed events
relating to a call. This timer can get started from the packet input
routines that are run in softirq mode with just the RCU read lock held.
Unfortunately, because only the RCU read lock is held - and neither ref or
other lock is taken - the call can start getting destroyed at the same time
a packet comes in addressed to that call. This causes the timer - which
was already stopped - to get restarted. Later, the timer dispatch code may
then oops if the timer got deallocated first.
Fix this by trying to take a ref on the rxrpc_call struct and, if
successful, passing that ref along to the timer. If the timer was already
running, the ref is discarded.
The timer completion routine can then pass the ref along to the call's work
item when it queues it. If the timer or work item where already
queued/running, the extra ref is discarded.
Fixes: a158bdd324 ("rxrpc: Fix call timeouts")
Reported-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
Tested-by: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Link: http://lists.infradead.org/pipermail/linux-afs/2022-March/005073.html
Link: https://lore.kernel.org/r/164865115696.2943015.11097991776647323586.stgit@warthog.procyon.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ed258f12e upstream.
When user delete vlan 0, as driver will not delete vlan 0 for hardware in
function hclge_set_vlan_filter_hw(), so vlan 0 in software vlan talbe should
not be deleted.
Fixes: fe4144d47e ("net: hns3: sync VLAN filter entries when kill VLAN ID failed")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 27ca8273fd upstream.
Per fstrim(8) we must round up the minlen argument to the fs block size.
The current calculation doesn't take into account devices that have a
discard granularity and requested minlen less than 1 fs block, so the
value can get shifted away to zero in the translation to fs blocks.
The zero minlen passed to gfs2_rgrp_send_discards() then allows
sb_issue_discard() to be called with nr_sects == 0 which returns -EINVAL
and results in gfs2_rgrp_send_discards() returning -EIO.
Make sure minlen is never < 1 fs block by taking the max of the
requested minlen and the fs block size before comparing to the device's
discard granularity and shifting to fs blocks.
Fixes: 076f0faa76 ("GFS2: Fix FITRIM argument handling")
Signed-off-by: Andrew Price <anprice@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 915593a7a6 upstream.
Clang static analysis reports this issue
interface.c:810:8: warning: Passed-by-value struct
argument contains uninitialized data
now = rtc_tm_to_ktime(tm);
^~~~~~~~~~~~~~~~~~~
tm is set by a successful call to __rtc_read_time()
but its return status is not checked. Check if
it was successful before setting the enabled flag.
Move the decl of err to function scope.
Fixes: 2b2f5ff00f ("rtc: interface: ignore expired timers when enqueuing new timers")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220326194236.2916310-1-trix@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ed4bb7715 upstream.
When splitting a value entry, we may need to add the new nodes to the LRU
list and remove the parent node from the LRU list. The WARN_ON checks
in shadow_lru_isolate() catch this oversight. This bug was latent
until we stopped splitting folios in shrink_page_list() with commit
820c4e2e6f ("mm/vmscan: Free non-shmem folios without splitting them").
That allows the creation of large shadow entries, and subsequently when
trying to page in a small page, we will split the large shadow entry
in __filemap_add_folio().
Fixes: 8fc75643c5 ("XArray: add xas_split")
Reported-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fa7b514d2b upstream.
Clang static analysis reports this issue:
| mcp251xfd-core.c:1813:7: warning: The left operand
| of '&' is a garbage value
| FIELD_GET(MCP251XFD_REG_DEVID_ID_MASK, dev_id),
| ^ ~~~~~~
dev_id is set in a successful call to mcp251xfd_register_get_dev_id().
Though the status of calls made by mcp251xfd_register_get_dev_id() are
checked and handled, their status' are not returned. So return err.
Fixes: 55e5b97f00 ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Link: https://lore.kernel.org/all/20220319153128.2164120-1-trix@redhat.com
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 136bed0bfd upstream.
Syzbot reported warning in usb_submit_urb() which is caused by wrong
endpoint type. We should check that in endpoint is actually present to
prevent this warning.
Found pipes are now saved to struct mcba_priv and code uses them
directly instead of making pipes in place.
Fail log:
| usb 5-1: BOGUS urb xfer, pipe 3 != type 1
| WARNING: CPU: 1 PID: 49 at drivers/usb/core/urb.c:502 usb_submit_urb+0xed2/0x18a0 drivers/usb/core/urb.c:502
| Modules linked in:
| CPU: 1 PID: 49 Comm: kworker/1:2 Not tainted 5.17.0-rc6-syzkaller-00184-g38f80f42147f #0
| Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-2 04/01/2014
| Workqueue: usb_hub_wq hub_event
| RIP: 0010:usb_submit_urb+0xed2/0x18a0 drivers/usb/core/urb.c:502
| ...
| Call Trace:
| <TASK>
| mcba_usb_start drivers/net/can/usb/mcba_usb.c:662 [inline]
| mcba_usb_probe+0x8a3/0xc50 drivers/net/can/usb/mcba_usb.c:858
| usb_probe_interface+0x315/0x7f0 drivers/usb/core/driver.c:396
| call_driver_probe drivers/base/dd.c:517 [inline]
Fixes: 51f3baad7d ("can: mcba_usb: Add support for Microchip CAN BUS Analyzer")
Link: https://lore.kernel.org/all/20220313100903.10868-1-paskripkin@gmail.com
Reported-and-tested-by: syzbot+3bc1dce0cc0052d60fde@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e3c658055 upstream.
If there is already an entry present that is of order >= XA_CHUNK_SHIFT
when we call xas_create_range(), xas_create_range() will misinterpret
that entry as a node and dereference xa_node->parent, generally leading
to a crash that looks something like this:
general protection fault, probably for non-canonical address 0xdffffc0000000001:
0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000008-0x000000000000000f]
CPU: 0 PID: 32 Comm: khugepaged Not tainted 5.17.0-rc8-syzkaller-00003-g56e337f2cf13 #0
RIP: 0010:xa_parent_locked include/linux/xarray.h:1207 [inline]
RIP: 0010:xas_create_range+0x2d9/0x6e0 lib/xarray.c:725
It's deterministically reproducable once you know what the problem is,
but producing it in a live kernel requires khugepaged to hit a race.
While the problem has been present since xas_create_range() was
introduced, I'm not aware of a way to hit it before the page cache was
converted to use multi-index entries.
Fixes: 6b24ca4a1a ("mm: Use multi-index entries in the page cache")
Reported-by: syzbot+0d2b0bf32ca5cfd09f2e@syzkaller.appspotmail.com
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77fc73ac89 upstream.
The previous commit fixed a memory leak on the send path in the event
that IPv6 is disabled at compile time, but how did a packet even arrive
there to begin with? It turns out we have previously allowed IPv6
endpoints even when IPv6 support is disabled at compile time. This is
awkward and inconsistent. Instead, let's just ignore all things IPv6,
the same way we do other malformed endpoints, in the case where IPv6 is
disabled.
Fixes: e7096c131e ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec59f128a9 upstream.
We make too nuanced use of ptr_ring to entirely move to the skb_array
wrappers, but we at least should avoid the naughty function pointer cast
when cleaning up skbs. Otherwise RAP/CFI will honk at us. This patch
uses the __skb_array_destroy_skb wrapper for the cleanup, rather than
directly providing kfree_skb, which is what other drivers in the same
situation do too.
Reported-by: PaX Team <pageexec@freemail.hu>
Fixes: 886fcee939 ("wireguard: receive: use ring buffer for incoming handshakes")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7057572745 upstream.
When renaming the whiteout file, the old whiteout file is not deleted.
Therefore, we add the old dentry size to the old dir like XFS.
Otherwise, an error may be reported due to `fscki->calc_sz != fscki->size`
in check_indes.
Fixes: 9e0a1fff8d ("ubifs: Implement RENAME_WHITEOUT")
Reported-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b67db8a6c upstream.
MM defined the rule [1] very clearly that once page was set with PG_private
flag, we should increment the refcount in that page, also main flows like
pageout(), migrate_page() will assume there is one additional page
reference count if page_has_private() returns true. Otherwise, we may
get a BUG in page migration:
page:0000000080d05b9d refcount:-1 mapcount:0 mapping:000000005f4d82a8
index:0xe2 pfn:0x14c12
aops:ubifs_file_address_operations [ubifs] ino:8f1 dentry name:"f30e"
flags: 0x1fffff80002405(locked|uptodate|owner_priv_1|private|node=0|
zone=1|lastcpupid=0x1fffff)
page dumped because: VM_BUG_ON_PAGE(page_count(page) != 0)
------------[ cut here ]------------
kernel BUG at include/linux/page_ref.h:184!
invalid opcode: 0000 [#1] SMP
CPU: 3 PID: 38 Comm: kcompactd0 Not tainted 5.15.0-rc5
RIP: 0010:migrate_page_move_mapping+0xac3/0xe70
Call Trace:
ubifs_migrate_page+0x22/0xc0 [ubifs]
move_to_new_page+0xb4/0x600
migrate_pages+0x1523/0x1cc0
compact_zone+0x8c5/0x14b0
kcompactd+0x2bc/0x560
kthread+0x18c/0x1e0
ret_from_fork+0x1f/0x30
Before the time, we should make clean a concept, what does refcount means
in page gotten from grab_cache_page_write_begin(). There are 2 situations:
Situation 1: refcount is 3, page is created by __page_cache_alloc.
TYPE_A - the write process is using this page
TYPE_B - page is assigned to one certain mapping by calling
__add_to_page_cache_locked()
TYPE_C - page is added into pagevec list corresponding current cpu by
calling lru_cache_add()
Situation 2: refcount is 2, page is gotten from the mapping's tree
TYPE_B - page has been assigned to one certain mapping
TYPE_A - the write process is using this page (by calling
page_cache_get_speculative())
Filesystem releases one refcount by calling put_page() in xxx_write_end(),
the released refcount corresponds to TYPE_A (write task is using it). If
there are any processes using a page, page migration process will skip the
page by judging whether expected_page_refs() equals to page refcount.
The BUG is caused by following process:
PA(cpu 0) kcompactd(cpu 1)
compact_zone
ubifs_write_begin
page_a = grab_cache_page_write_begin
add_to_page_cache_lru
lru_cache_add
pagevec_add // put page into cpu 0's pagevec
(refcnf = 3, for page creation process)
ubifs_write_end
SetPagePrivate(page_a) // doesn't increase page count !
unlock_page(page_a)
put_page(page_a) // refcnt = 2
[...]
PB(cpu 0)
filemap_read
filemap_get_pages
add_to_page_cache_lru
lru_cache_add
__pagevec_lru_add // traverse all pages in cpu 0's pagevec
__pagevec_lru_add_fn
SetPageLRU(page_a)
isolate_migratepages
isolate_migratepages_block
get_page_unless_zero(page_a)
// refcnt = 3
list_add(page_a, from_list)
migrate_pages(from_list)
__unmap_and_move
move_to_new_page
ubifs_migrate_page(page_a)
migrate_page_move_mapping
expected_page_refs get 3
(migration[1] + mapping[1] + private[1])
release_pages
put_page_testzero(page_a) // refcnt = 3
page_ref_freeze // refcnt = 0
page_ref_dec_and_test(0 - 1 = -1)
page_ref_unfreeze
VM_BUG_ON_PAGE(-1 != 0, page)
UBIFS doesn't increase the page refcount after setting private flag, which
leads to page migration task believes the page is not used by any other
processes, so the page is migrated. This causes concurrent accessing on
page refcount between put_page() called by other process(eg. read process
calls lru_cache_add) and page_ref_unfreeze() called by migration task.
Actually zhangjun has tried to fix this problem [2] by recalculating page
refcnt in ubifs_migrate_page(). It's better to follow MM rules [1], because
just like Kirill suggested in [2], we need to check all users of
page_has_private() helper. Like f2fs does in [3], fix it by adding/deleting
refcount when setting/clearing private for a page. BTW, according to [4],
we set 'page->private' as 1 because ubifs just simply SetPagePrivate().
And, [5] provided a common helper to set/clear page private, ubifs can
use this helper following the example of iomap, afs, btrfs, etc.
Jump [6] to find a reproducer.
[1] https://lore.kernel.org/lkml/2b19b3c4-2bc4-15fa-15cc-27a13e5c7af1@aol.com
[2] https://www.spinics.net/lists/linux-mtd/msg04018.html
[3] http://lkml.iu.edu/hypermail/linux/kernel/1903.0/03313.html
[4] https://lore.kernel.org/linux-f2fs-devel/20210422154705.GO3596236@casper.infradead.org
[5] https://lore.kernel.org/all/20200517214718.468-1-guoqing.jiang@cloud.ionos.com
[6] https://bugzilla.kernel.org/show_bug.cgi?id=214961
Fixes: 1e51764a3c ("UBIFS: add new flash file system")
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f2262a334 upstream.
Function ubifs_wbuf_write_nolock() may access buf out of bounds in
following process:
ubifs_wbuf_write_nolock():
aligned_len = ALIGN(len, 8); // Assume len = 4089, aligned_len = 4096
if (aligned_len <= wbuf->avail) ... // Not satisfy
if (wbuf->used) {
ubifs_leb_write() // Fill some data in avail wbuf
len -= wbuf->avail; // len is still not 8-bytes aligned
aligned_len -= wbuf->avail;
}
n = aligned_len >> c->max_write_shift;
if (n) {
n <<= c->max_write_shift;
err = ubifs_leb_write(c, wbuf->lnum, buf + written,
wbuf->offs, n);
// n > len, read out of bounds less than 8(n-len) bytes
}
, which can be catched by KASAN:
=========================================================
BUG: KASAN: slab-out-of-bounds in ecc_sw_hamming_calculate+0x1dc/0x7d0
Read of size 4 at addr ffff888105594ff8 by task kworker/u8:4/128
Workqueue: writeback wb_workfn (flush-ubifs_0_0)
Call Trace:
kasan_report.cold+0x81/0x165
nand_write_page_swecc+0xa9/0x160
ubifs_leb_write+0xf2/0x1b0 [ubifs]
ubifs_wbuf_write_nolock+0x421/0x12c0 [ubifs]
write_head+0xdc/0x1c0 [ubifs]
ubifs_jnl_write_inode+0x627/0x960 [ubifs]
wb_workfn+0x8af/0xb80
Function ubifs_wbuf_write_nolock() accepts that parameter 'len' is not 8
bytes aligned, the 'len' represents the true length of buf (which is
allocated in 'ubifs_jnl_xxx', eg. ubifs_jnl_write_inode), so
ubifs_wbuf_write_nolock() must handle the length read from 'buf' carefully
to write leb safely.
Fetch a reproducer in [Link].
Fixes: 1e51764a3c ("UBIFS: add new flash file system")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=214785
Reported-by: Chengsong Ke <kechengsong@huawei.com>
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b83ec057d upstream.
Make 'ui->data_len' aligned with 8 bytes before it is assigned to
dirtied_ino_d. Since 8871d84c8f8b0c6b("ubifs: convert to fileattr")
applied, 'setflags()' only affects regular files and directories, only
xattr inode, symlink inode and special inode(pipe/char_dev/block_dev)
have none- zero 'ui->data_len' field, so assertion
'!(req->dirtied_ino_d & 7)' cannot fail in ubifs_budget_space().
To avoid assertion fails in future evolution(eg. setflags can operate
special inodes), it's better to make dirtied_ino_d 8 bytes aligned,
after all aligned size is still zero for regular files.
Fixes: 1e51764a3c ("UBIFS: add new flash file system")
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 716b457302 upstream.
whiteout inode should be put when do_tmpfile() failed if inode has been
initialized. Otherwise we will get following warning during umount:
UBIFS error (ubi0:0 pid 1494): ubifs_assert_failed [ubifs]: UBIFS
assert failed: c->bi.dd_growth == 0, in fs/ubifs/super.c:1930
VFS: Busy inodes after unmount of ubifs. Self-destruct in 5 seconds.
Fixes: 9e0a1fff8d ("ubifs: Implement RENAME_WHITEOUT")
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Suggested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40a8f0d5e7 upstream.
'whiteout_ui->data' will be freed twice if space budget fail for
rename whiteout operation as following process:
rename_whiteout
dev = kmalloc
whiteout_ui->data = dev
kfree(whiteout_ui->data) // Free first time
iput(whiteout)
ubifs_free_inode
kfree(ui->data) // Double free!
KASAN reports:
==================================================================
BUG: KASAN: double-free or invalid-free in ubifs_free_inode+0x4f/0x70
Call Trace:
kfree+0x117/0x490
ubifs_free_inode+0x4f/0x70 [ubifs]
i_callback+0x30/0x60
rcu_do_batch+0x366/0xac0
__do_softirq+0x133/0x57f
Allocated by task 1506:
kmem_cache_alloc_trace+0x3c2/0x7a0
do_rename+0x9b7/0x1150 [ubifs]
ubifs_rename+0x106/0x1f0 [ubifs]
do_syscall_64+0x35/0x80
Freed by task 1506:
kfree+0x117/0x490
do_rename.cold+0x53/0x8a [ubifs]
ubifs_rename+0x106/0x1f0 [ubifs]
do_syscall_64+0x35/0x80
The buggy address belongs to the object at ffff88810238bed8 which
belongs to the cache kmalloc-8 of size 8
==================================================================
Let ubifs_free_inode() free 'whiteout_ui->data'. BTW, delete unused
assignment 'whiteout_ui->data_len = 0', process 'ubifs_evict_inode()
-> ubifs_jnl_delete_inode() -> ubifs_jnl_write_inode()' doesn't need it
(because 'inc_nlink(whiteout)' won't be excuted by 'goto out_release',
and the nlink of whiteout inode is 0).
Fixes: 9e0a1fff8d ("ubifs: Implement RENAME_WHITEOUT")
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c15e0ae42c upstream.
If apic_id is less than min, and (max - apic_id) is greater than
KVM_IPI_CLUSTER_SIZE, then the third check condition is satisfied but
the new apic_id does not fit the bitmask. In this case __send_ipi_mask
should send the IPI.
This is mostly theoretical, but it can happen if the apic_ids on three
iterations of the loop are for example 1, KVM_IPI_CLUSTER_SIZE, 0.
Fixes: aaffcfd1e8 ("KVM: X86: Implement PV IPIs in linux guest")
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Message-Id: <1646814944-51801-1-git-send-email-lirongqing@baidu.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f6de5cbeb upstream.
Tie the lifetime the KVM module to the lifetime of each VM via
kvm.users_count. This way anything that grabs a reference to the VM via
kvm_get_kvm() cannot accidentally outlive the KVM module.
Prior to this commit, the lifetime of the KVM module was tied to the
lifetime of /dev/kvm file descriptors, VM file descriptors, and vCPU
file descriptors by their respective file_operations "owner" field.
This approach is insufficient because references grabbed via
kvm_get_kvm() do not prevent closing any of the aforementioned file
descriptors.
This fixes a long standing theoretical bug in KVM that at least affects
async page faults. kvm_setup_async_pf() grabs a reference via
kvm_get_kvm(), and drops it in an asynchronous work callback. Nothing
prevents the VM file descriptor from being closed and the KVM module
from being unloaded before this callback runs.
Fixes: af585b921e ("KVM: Halt vcpu if page it tries to access is swapped out")
Fixes: 3d3aab1b97 ("KVM: set owner of cpu and vm file operations")
Cc: stable@vger.kernel.org
Suggested-by: Ben Gardon <bgardon@google.com>
[ Based on a patch from Ben implemented for Google's kernel. ]
Signed-off-by: David Matlack <dmatlack@google.com>
Message-Id: <20220303183328.1499189-2-dmatlack@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1e34d3253 upstream.
Setting non-zero values to SYNIC/STIMER MSRs activates certain features,
this should not happen when KVM_CAP_HYPERV_SYNIC{,2} was not activated.
Note, it would've been better to forbid writing anything to SYNIC/STIMER
MSRs, including zeroes, however, at least QEMU tries clearing
HV_X64_MSR_STIMER0_CONFIG without SynIC. HV_X64_MSR_EOM MSR is somewhat
'special' as writing zero there triggers an action, this also should not
happen when SynIC wasn't activated.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20220325132140.25650-4-vkuznets@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eabd9a3807 upstream.
cros_ec_trace.h defined 5 tracing events, 2 for cros_ec_proto and
3 for cros_ec_sensorhub_ring.
These 2 files are in different kernel modules, the traces are defined
twice in the kernel which leads to problem enabling only some traces.
Move sensorhub traces from cros_ec_trace.h to cros_ec_sensorhub_trace.h
and enable them only in cros_ec_sensorhub kernel module.
Check we can now enable any single traces: without this patch,
we can only enable all sensorhub traces or none.
Fixes: d453ceb654 ("platform/chrome: sensorhub: Add trace events for sample")
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220122001301.640337-1-gwendal@chromium.org
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c02aada06d upstream.
User experienced device lost. The log shows Get port data base command was
queued up, failed, and requeued again. Every time it is requeued, it set
the FCF_ASYNC_ACTIVE. This prevents any recovery code from occurring
because driver thinks a recovery is in progress for this session. In
essence, this session is hung. The reason it gets into this place is the
session deletion got in front of this call due to link perturbation.
Break the requeue cycle and exit. The session deletion code will trigger a
session relogin.
Link: https://lore.kernel.org/r/20220310092604.22950-8-njavali@marvell.com
Fixes: 726b854870 ("qla2xxx: Add framework for async fabric discovery")
Cc: stable@vger.kernel.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6a45c8e137 upstream.
User experienced some of the LUN failed to get rediscovered after long
cable pull test. The issue is triggered by a race condition between driver
setting session online state vs starting the LUN scan process at the same
time. Current code set the online state after notifying the session is
available. In this case, trigger to start the LUN scan process happened
before driver could set the session in online state. LUN scan ends up with
failure due to the session online check was failing.
Set the online state before reporting of the availability of the session.
Link: https://lore.kernel.org/r/20220310092604.22950-3-njavali@marvell.com
Fixes: aecf043443 ("scsi: qla2xxx: Fix Remote port registration")
Cc: stable@vger.kernel.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8667d0d64d upstream.
Building tinyconfig with gcc (Debian 11.2.0-16) and assembler (Debian
2.37.90.20220207) the following build error shows up:
{standard input}: Assembler messages:
{standard input}:1190: Error: unrecognized opcode: `stbcix'
{standard input}:1433: Error: unrecognized opcode: `lwzcix'
{standard input}:1453: Error: unrecognized opcode: `stbcix'
{standard input}:1460: Error: unrecognized opcode: `stwcix'
{standard input}:1596: Error: unrecognized opcode: `stbcix'
...
Rework to add assembler directives [1] around the instruction. Going
through them one by one shows that the changes should be safe. Like
__get_user_atomic_128_aligned() is only called in p9_hmi_special_emu(),
which according to the name is specific to power9. And __raw_rm_read*()
are only called in things that are powernv or book3s_hv specific.
[1] https://sourceware.org/binutils/docs/as/PowerPC_002dPseudo.html#PowerPC_002dPseudo
Cc: stable@vger.kernel.org
Co-developed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Segher Boessenkool <segher@kernel.crashing.org>
[mpe: Make commit subject more descriptive]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220224162215.3406642-2-anders.roxell@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3354ef5a59 upstream.
Explicitly check for present SPTEs when clearing dirty bits in the TDP
MMU. This isn't strictly required for correctness, as setting the dirty
bit in a defunct SPTE will not change the SPTE from !PRESENT to PRESENT.
However, the guarded MMU_WARN_ON() in spte_ad_need_write_protect() would
complain if anyone actually turned on KVM's MMU debugging.
Fixes: a6a0b05da9 ("kvm: x86/mmu: Support dirty logging for the TDP MMU")
Cc: Ben Gardon <bgardon@google.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Ben Gardon <bgardon@google.com>
Message-Id: <20220226001546.360188-3-seanjc@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ef248d9bd6 ]
This fixes the near-silence of the headphone jack on the ALC256-based
Samsung Galaxy Book Flex Alpha (NP730QCJ). The magic verbs were found
through trial and error, using known ALC298 hacks as inspiration. The
fixup is auto-enabled only when the NP730QCJ is detected. It can be
manually enabled using model=alc256-samsung-headphone.
Signed-off-by: Matt Kramer <mccleetus@gmail.com>
Link: https://lore.kernel.org/r/3168355.aeNJFYEL58@linus
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc0b582c85 ]
As warned by sparse:
atomisp: drivers/staging/media/atomisp/pci/atomisp_acc.c:508 atomisp_acc_load_extensions() warn: iterator used outside loop: 'acc_fw'
The acc_fw interactor is used outside the loop, at the error handling
logic. On most cases, this is actually safe there, but, if
atomisp_css_set_acc_parameters() has an error, an attempt to use it
will pick an invalid value for acc_fw.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6c9219ca1 ]
Even if the current WARN() notifies the user that something is severely
wrong, we can still end up in a PANIC() when trying to invoke the missing
->enable_sdio_irq() ops. Therefore, let's also return an error code and
prevent the host from being added.
While at it, move the code into a separate function to prepare for
subsequent changes and for further host caps validations.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20220303165142.129745-1-ulf.hansson@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07922937e9 ]
hdpvr_register_videodev is responsible to initialize a worker in
hdpvr_device. However, the worker is only initialized at
hdpvr_start_streaming other than hdpvr_register_videodev.
When hdpvr_probe does not initialize its worker, the hdpvr_disconnect
will encounter one WARN in flush_work.The stack trace is as follows:
hdpvr_disconnect+0xb8/0xf2 drivers/media/usb/hdpvr/hdpvr-core.c:425
usb_unbind_interface+0xbf/0x3a0 drivers/usb/core/driver.c:458
__device_release_driver drivers/base/dd.c:1206 [inline]
device_release_driver_internal+0x22a/0x230 drivers/base/dd.c:1237
bus_remove_device+0x108/0x160 drivers/base/bus.c:529
device_del+0x1fe/0x510 drivers/base/core.c:3592
usb_disable_device+0xd1/0x1d0 drivers/usb/core/message.c:1419
usb_disconnect+0x109/0x330 drivers/usb/core/hub.c:2228
Fix this by moving the initialization of dev->worker to the starting of
hdpvr_register_videodev
Reported-by: syzkaller <syzkaller@googlegroups.com>
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f01d09b2b ]
When the sm712fb driver writes three bytes to the framebuffer, the
driver will crash:
BUG: unable to handle page fault for address: ffffc90001ffffff
RIP: 0010:smtcfb_write+0x454/0x5b0
Call Trace:
vfs_write+0x291/0xd60
? do_sys_openat2+0x27d/0x350
? __fget_light+0x54/0x340
ksys_write+0xce/0x190
do_syscall_64+0x43/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
Fix it by removing the open-coded endianness fixup-code.
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4036b29a14 ]
Make sure in .probe() to set driver data before the function is left to
make it possible in .remove() to undo the actions done.
This fixes a potential memory leak and stops returning an error code in
.remove() that is ignored by the driver core anyhow.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0092c25b54 ]
This patch fixes the tristate configuration for i2c3 function assigned
to the dtf pins on the Tamonten Tegra20 SoM.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a06fcb15b ]
test_kernel_ptr() uses access_ok() to figure out if a given address
points to user space instead of kernel space. However on architectures
that set CONFIG_ALTERNATE_USER_ADDRESS_SPACE, a pointer can be valid
for both, and the check always fails because access_ok() returns true.
Make the check for user space pointers conditional on the type of
address space layout.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23fc539e81 ]
On some architectures, access_ok() does not do any argument type
checking, so replacing the definition with a generic one causes
a few warnings for harmless issues that were never caught before.
Fix the ones that I found either through my own test builds or
that were reported by the 0-day bot.
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56cb61f70e ]
Some cx88 video cards may have transport stream status interrupts set
to 1 from cold start, causing errors like this:
cx88xx: cx88_print_irqbits: core:irq mpeg [0x100000] ts_err?*
cx8802: cx8802_mpeg_irq: mpeg:general errors: 0x00100000
According to CX2388x datasheet, the interrupt status register should be
cleared before enabling IRQs to stream video.
Fix it by clearing the Transport Stream Interrupt Status register.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7d344a2bd ]
In the case like dmaengine which's not a dai but as a component, the
num_dai is zero, dmaengine component has the same component_of_node
as cpu dai, when cpu dai component is not ready, but dmaengine component
is ready, try to get cpu dai name, the snd_soc_get_dai_name() return
-EINVAL, not -EPROBE_DEFER, that cause below error:
asoc-simple-card <card name>: parse error -22
asoc-simple-card: probe of <card name> failed with error -22
The sound card failed to probe.
So this patch fixes the issue above by skipping the zero num_dai
component in searching dai name.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1644491952-7457-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 618682b350 ]
This patch fixes the kernel warning
"cacheinfo: Unable to detect cache hierarchy for CPU 0"
for the bcm2711 on newer kernel versions.
Signed-off-by: Richard Schleich <rs@noreya.tech>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
[florian: Align and remove comments matching property values]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4cb7df64c7 ]
The audio_mclk_root_clk was added as a gate with the CCGR121 (0x4790),
but according to the reference manual, there is no such gate. Moreover,
the consumer driver of the mentioned clock might gate it and leave
the ECSPI2 (the true owner of that gate) hanging. So lets use the
audio_mclk_post_div, which is the parent.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d119678708 ]
Tweak the ftrace return paths to avoid redundant loads of SP, as well as
unnecessary clobbering of IP.
This also fixes the inconsistency of using MOV to perform a function
return, which is sub-optimal on recent micro-architectures but more
importantly, does not perform an interworking return, unlike compiler
generated function returns in Thumb2 builds.
Let's fix this by popping PC from the stack like most ordinary code
does.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c39a01154 ]
The TrekStor SurfTab duo W1 10.1 has a hw bug where turning eldo2 back on
after having turned it off causes the CPLM3218 ambient-light-sensor on
the front camera sensor's I2C bus to crash, hanging the bus.
Add a DMI quirk table for systems on which to leave eldo2 on.
Note an alternative fix is to turn off the CPLM3218 ambient-light-sensor
as long as the camera sensor is being used, this is what Windows seems
to do as a workaround (based on analyzing the DSDT). But that is not
easy to do cleanly under Linux.
Link: https://lore.kernel.org/linux-media/20220116215204.307649-10-hdegoede@redhat.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bdf8762da2 ]
This patch fixes the kernel warning
"cacheinfo: Unable to detect cache hierarchy for CPU 0"
for the bcm2837 on newer kernel versions.
Signed-off-by: Richard Schleich <rs@noreya.tech>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
[florian: Align and remove comments matching property values]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24565bc411 ]
coccinelle report:
./drivers/video/fbdev/omap2/omapfb/displays/panel-sony-acx565akm.c:
479:9-17: WARNING: use scnprintf or sprintf
Use sysfs_emit instead of scnprintf or sprintf makes more sense.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Yang Guang <yang.guang5@zte.com.cn>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c6f402bdc ]
Do a sanity check on pixclock value to avoid divide by zero.
If the pixclock value is zero, the cirrusfb driver will round up
pixclock to get the derived frequency as close to maxclock as
possible.
Syzkaller reported a divide error in cirrusfb_check_pixclock.
divide error: 0000 [#1] SMP KASAN PTI
CPU: 0 PID: 14938 Comm: cirrusfb_test Not tainted 5.15.0-rc6 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-2
RIP: 0010:cirrusfb_check_var+0x6f1/0x1260
Call Trace:
fb_set_var+0x398/0xf90
do_fb_ioctl+0x4b8/0x6f0
fb_ioctl+0xeb/0x130
__x64_sys_ioctl+0x19d/0x220
do_syscall_64+0x3a/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
Signed-off-by: George Kennedy <george.kennedy@oracle.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8738ddcac6 ]
w100fb_probe() did not reset the global state to its initial state. This
can result in invocation of iounmap() even when there was not the
appropriate successful call of ioremap(). For instance, this may be the
case if first probe fails after two successful ioremap() while second
probe fails when first ioremap() fails. The similar issue is with
w100fb_remove(). The patch fixes both bugs.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Co-developed-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Signed-off-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37a1a2e6ee ]
Coverity complains of a possible buffer overflow. However,
given the 'static' scope of nvidia_setup_i2c_bus() it looks
like that can't happen after examiniing the call sites.
CID 19036 (#1 of 1): Copy into fixed size buffer (STRING_OVERFLOW)
1. fixed_size_dest: You might overrun the 48-character fixed-size string
chan->adapter.name by copying name without checking the length.
2. parameter_as_source: Note: This defect has an elevated risk because the
source argument is a parameter of the current function.
89 strcpy(chan->adapter.name, name);
Fix this warning by using strscpy() which will silence the warning and
prevent any future buffer overflows should the names used to identify the
channel become much longer.
Cc: Antonino Daplas <adaplas@gmail.com>
Cc: linux-fbdev@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 914941827a ]
This fixes several issues found with 'v4l2-compliance -s':
1) read()/write() is supported, but not reported in the capabilities
2) S_STD(G_STD()) failed: setting the same standard should just return 0.
3) G_PARM failed to set readbuffers.
4) different field values in the format vs. what v4l2_buffer reported.
5) zero the sequence number when starting streaming.
6) drop VB_USERPTR: makes no sense with dma_contig streaming.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3b86f4e55 ]
On the case tmp_dcim=1, the index of buffer is miscalculated.
This generate a NULL pointer dereference later.
So let's fix the calcul and add a check to prevent this to reappear.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 82e3a496eb ]
Move some code out of zr36057_init() and create new functions for handling
zr->video_dev. This permit to ease code reading and fix a zr->video_dev
memory leak.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d284af43f7 ]
In lz4_decompress_pages(), if size of decompressed data is not equal to
expected one, we should print the size rather than size of target buffer
for decompressed data, fix it.
Signed-off-by: Chao Yu <chao.yu@oppo.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50719bf344 ]
These have been incorrect since the function was introduced.
A proper kerneldoc comment is added since this function, though
static, is part of an external interface.
Reported-by: Dai Ngo <dai.ngo@oracle.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc5095747e ]
[un]pin_user_pages_remote is dirtying pages without properly warning
the file system in advance. A related race was noted by Jan Kara in
2018[1]; however, more recently instead of it being a very hard-to-hit
race, it could be reliably triggered by process_vm_writev(2) which was
discovered by Syzbot[2].
This is technically a bug in mm/gup.c, but arguably ext4 is fragile in
that if some other kernel subsystem dirty pages without properly
notifying the file system using page_mkwrite(), ext4 will BUG, while
other file systems will not BUG (although data will still be lost).
So instead of crashing with a BUG, issue a warning (since there may be
potential data loss) and just mark the page as clean to avoid
unprivileged denial of service attacks until the problem can be
properly fixed. More discussion and background can be found in the
thread starting at [2].
[1] https://lore.kernel.org/linux-mm/20180103100430.GE4911@quack2.suse.cz
[2] https://lore.kernel.org/r/Yg0m6IjcNmfaSokM@google.com
Reported-by: syzbot+d59332e2db681cf18f0318a06e994ebbb529a8db@syzkaller.appspotmail.com
Reported-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Link: https://lore.kernel.org/r/YiDS9wVfq4mM2jGK@mit.edu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfdc502a4a ]
In case of flex_bg feature (which is by default enabled), extents for
any given inode might span across blocks from two different block group.
ext4_mb_mark_bb() only reads the buffer_head of block bitmap once for the
starting block group, but it fails to read it again when the extent length
boundary overflows to another block group. Then in this below loop it
accesses memory beyond the block group bitmap buffer_head and results
into a data abort.
for (i = 0; i < clen; i++)
if (!mb_test_bit(blkoff + i, bitmap_bh->b_data) == !state)
already++;
This patch adds this functionality for checking block group boundary in
ext4_mb_mark_bb() and update the buffer_head(bitmap_bh) for every different
block group.
w/o this patch, I was easily able to hit a data access abort using Power platform.
<...>
[ 74.327662] EXT4-fs error (device loop3): ext4_mb_generate_buddy:1141: group 11, block bitmap and bg descriptor inconsistent: 21248 vs 23294 free clusters
[ 74.533214] EXT4-fs (loop3): shut down requested (2)
[ 74.536705] Aborting journal on device loop3-8.
[ 74.702705] BUG: Unable to handle kernel data access on read at 0xc00000005e980000
[ 74.703727] Faulting instruction address: 0xc0000000007bffb8
cpu 0xd: Vector: 300 (Data Access) at [c000000015db7060]
pc: c0000000007bffb8: ext4_mb_mark_bb+0x198/0x5a0
lr: c0000000007bfeec: ext4_mb_mark_bb+0xcc/0x5a0
sp: c000000015db7300
msr: 800000000280b033
dar: c00000005e980000
dsisr: 40000000
current = 0xc000000027af6880
paca = 0xc00000003ffd5200 irqmask: 0x03 irq_happened: 0x01
pid = 5167, comm = mount
<...>
enter ? for help
[c000000015db7380] c000000000782708 ext4_ext_clear_bb+0x378/0x410
[c000000015db7400] c000000000813f14 ext4_fc_replay+0x1794/0x2000
[c000000015db7580] c000000000833f7c do_one_pass+0xe9c/0x12a0
[c000000015db7710] c000000000834504 jbd2_journal_recover+0x184/0x2d0
[c000000015db77c0] c000000000841398 jbd2_journal_load+0x188/0x4a0
[c000000015db7880] c000000000804de8 ext4_fill_super+0x2638/0x3e10
[c000000015db7a40] c0000000005f8404 get_tree_bdev+0x2b4/0x350
[c000000015db7ae0] c0000000007ef058 ext4_get_tree+0x28/0x40
[c000000015db7b00] c0000000005f6344 vfs_get_tree+0x44/0x100
[c000000015db7b70] c00000000063c408 path_mount+0xdd8/0xe70
[c000000015db7c40] c00000000063c8f0 sys_mount+0x450/0x550
[c000000015db7d50] c000000000035770 system_call_exception+0x4a0/0x4e0
[c000000015db7e10] c00000000000c74c system_call_common+0xec/0x250
Signed-off-by: Ritesh Harjani <riteshh@linux.ibm.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/2609bc8f66fc15870616ee416a18a3d392a209c4.1644992609.git.riteshh@linux.ibm.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb7275acd6 ]
When dumping lock_classes information via /proc/lockdep, we can't take
the lockdep lock as the lock hold time is indeterminate. Iterating
over all_lock_classes without holding lock can be dangerous as there
is a slight chance that it may branch off to other lists leading to
infinite loop or even access invalid memory if changes are made to
all_lock_classes list in parallel.
To avoid this problem, iteration of lock classes is now done directly
on the lock_classes array itself. The lock_classes_in_use bitmap is
checked to see if the lock class is being used. To avoid iterating
the full array all the times, a new max_lock_class_idx value is added
to track the maximum lock_class index that is currently being used.
We can theoretically take the lockdep lock for iterating all_lock_classes
when other lockdep files (lockdep_stats and lock_stat) are accessed as
the lock hold time will be shorter for them. For consistency, they are
also modified to iterate the lock_classes array directly.
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20220211035526.1329503-2-longman@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 841aee4d75 ]
Put NVMe/TCP sockets in their own class to avoid some lockdep warnings.
Sockets created by nvme-tcp are not exposed to user-space, and will not
trigger certain code paths that the general socket API exposes.
Lockdep complains about a circular dependency between the socket and
filesystem locks, because setsockopt can trigger a page fault with a
socket lock held, but nvme-tcp sends requests on the socket while file
system locks are held.
======================================================
WARNING: possible circular locking dependency detected
5.15.0-rc3 #1 Not tainted
------------------------------------------------------
fio/1496 is trying to acquire lock:
(sk_lock-AF_INET){+.+.}-{0:0}, at: tcp_sendpage+0x23/0x80
but task is already holding lock:
(&xfs_dir_ilock_class/5){+.+.}-{3:3}, at: xfs_ilock+0xcf/0x290 [xfs]
which lock already depends on the new lock.
other info that might help us debug this:
chain exists of:
sk_lock-AF_INET --> sb_internal --> &xfs_dir_ilock_class/5
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&xfs_dir_ilock_class/5);
lock(sb_internal);
lock(&xfs_dir_ilock_class/5);
lock(sk_lock-AF_INET);
*** DEADLOCK ***
6 locks held by fio/1496:
#0: (sb_writers#13){.+.+}-{0:0}, at: path_openat+0x9fc/0xa20
#1: (&inode->i_sb->s_type->i_mutex_dir_key){++++}-{3:3}, at: path_openat+0x296/0xa20
#2: (sb_internal){.+.+}-{0:0}, at: xfs_trans_alloc_icreate+0x41/0xd0 [xfs]
#3: (&xfs_dir_ilock_class/5){+.+.}-{3:3}, at: xfs_ilock+0xcf/0x290 [xfs]
#4: (hctx->srcu){....}-{0:0}, at: hctx_lock+0x51/0xd0
#5: (&queue->send_mutex){+.+.}-{3:3}, at: nvme_tcp_queue_rq+0x33e/0x380 [nvme_tcp]
This annotation lets lockdep analyze nvme-tcp controlled sockets
independently of what the user-space sockets API does.
Link: https://lore.kernel.org/linux-nvme/CAHj4cs9MDYLJ+q+2_GXUK9HxFizv2pxUryUR0toX974M040z7g@mail.gmail.com/
Signed-off-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e00b0a2ab8 ]
Currently, the parisc kernel does not fully support non-access TLB
fault handling for probe instructions. In the fast path, we set the
target register to zero if it is not a shadowed register. The slow
path is not implemented, so we call do_page_fault. The architecture
indicates that non-access faults should not cause a page fault from
disk.
This change adds to code to provide non-access fault support for
probe instructions. It also modifies the handling of faults on
userspace so that if the address lies in a valid VMA and the access
type matches that for the VMA, the probe target register is set to
one. Otherwise, the target register is set to zero.
This was done to make probe instructions more useful for userspace.
Probe instructions are not very useful if they set the target register
to zero whenever a page is not present in memory. Nominally, the
purpose of the probe instruction is determine whether read or write
access to a given address is allowed.
This fixes a problem in function pointer comparison noticed in the
glibc testsuite (stdio-common/tst-vfprintf-user-type). The same
problem is likely in glibc (_dl_lookup_address).
V2 adds flush and lpa instruction support to handle_nadtlb_fault.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f8dec1162 ]
Platforms with large BERT table data can trigger soft lockup errors
while attempting to print the entire BERT table data to the console at
boot:
watchdog: BUG: soft lockup - CPU#160 stuck for 23s! [swapper/0:1]
Observed on Ampere Altra systems with a single BERT record of ~250KB.
The original bert driver appears to have assumed relatively small table
data. Since it is impractical to reassemble large table data from
interwoven console messages, and the table data is available in
/sys/firmware/acpi/tables/data/BERT
limit the size for tables printed to the console to 1024 (for no reason
other than it seemed like a good place to kick off the discussion, would
appreciate feedback from existing users in terms of what size would
maintain their current usage model).
Alternatively, we could make printing a CONFIG option, use the
bert_disable boot arg (or something similar), or use a debug log level.
However, all those solutions require extra steps or change the existing
behavior for small table data. Limiting the size preserves existing
behavior on existing platforms with small table data, and eliminates the
soft lockups for platforms with large table data, while still making it
available.
Signed-off-by: Darren Hart <darren@os.amperecomputing.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 633174a704 ]
Buidling raid6test on Ubuntu 21.10 (ppc64le) with GNU Make 4.3 shows the
errors below:
$ cd lib/raid6/test/
$ make
<stdin>:1:1: error: stray ‘\’ in program
<stdin>:1:2: error: stray ‘#’ in program
<stdin>:1:11: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ \
before ‘<’ token
[...]
The errors come from the HAS_ALTIVEC test, which fails, and the POWER
optimized versions are not built. That’s also reason nobody noticed on the
other architectures.
GNU Make 4.3 does not remove the backslash anymore. From the 4.3 release
announcment:
> * WARNING: Backward-incompatibility!
> Number signs (#) appearing inside a macro reference or function invocation
> no longer introduce comments and should not be escaped with backslashes:
> thus a call such as:
> foo := $(shell echo '#')
> is legal. Previously the number sign needed to be escaped, for example:
> foo := $(shell echo '\#')
> Now this latter will resolve to "\#". If you want to write makefiles
> portable to both versions, assign the number sign to a variable:
> H := \#
> foo := $(shell echo '$H')
> This was claimed to be fixed in 3.81, but wasn't, for some reason.
> To detect this change search for 'nocomment' in the .FEATURES variable.
So, do the same as commit 9564a8cf42 ("Kbuild: fix # escaping in .cmd
files for future Make") and commit 929bef4677 ("bpf: Use $(pound) instead
of \# in Makefiles") and define and use a $(pound) variable.
Reference for the change in make:
https://git.savannah.gnu.org/cgit/make.git/commit/?id=c6966b323811c37acedff05b57
Cc: Matt Brown <matthew.brown.dev@gmail.com>
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Song Liu <song@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab552fcb17 ]
KASAN reports a use-after-free report when doing normal scsi-mq test
[69832.239032] ==================================================================
[69832.241810] BUG: KASAN: use-after-free in bfq_dispatch_request+0x1045/0x44b0
[69832.243267] Read of size 8 at addr ffff88802622ba88 by task kworker/3:1H/155
[69832.244656]
[69832.245007] CPU: 3 PID: 155 Comm: kworker/3:1H Not tainted 5.10.0-10295-g576c6382529e #8
[69832.246626] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014
[69832.249069] Workqueue: kblockd blk_mq_run_work_fn
[69832.250022] Call Trace:
[69832.250541] dump_stack+0x9b/0xce
[69832.251232] ? bfq_dispatch_request+0x1045/0x44b0
[69832.252243] print_address_description.constprop.6+0x3e/0x60
[69832.253381] ? __cpuidle_text_end+0x5/0x5
[69832.254211] ? vprintk_func+0x6b/0x120
[69832.254994] ? bfq_dispatch_request+0x1045/0x44b0
[69832.255952] ? bfq_dispatch_request+0x1045/0x44b0
[69832.256914] kasan_report.cold.9+0x22/0x3a
[69832.257753] ? bfq_dispatch_request+0x1045/0x44b0
[69832.258755] check_memory_region+0x1c1/0x1e0
[69832.260248] bfq_dispatch_request+0x1045/0x44b0
[69832.261181] ? bfq_bfqq_expire+0x2440/0x2440
[69832.262032] ? blk_mq_delay_run_hw_queues+0xf9/0x170
[69832.263022] __blk_mq_do_dispatch_sched+0x52f/0x830
[69832.264011] ? blk_mq_sched_request_inserted+0x100/0x100
[69832.265101] __blk_mq_sched_dispatch_requests+0x398/0x4f0
[69832.266206] ? blk_mq_do_dispatch_ctx+0x570/0x570
[69832.267147] ? __switch_to+0x5f4/0xee0
[69832.267898] blk_mq_sched_dispatch_requests+0xdf/0x140
[69832.268946] __blk_mq_run_hw_queue+0xc0/0x270
[69832.269840] blk_mq_run_work_fn+0x51/0x60
[69832.278170] process_one_work+0x6d4/0xfe0
[69832.278984] worker_thread+0x91/0xc80
[69832.279726] ? __kthread_parkme+0xb0/0x110
[69832.280554] ? process_one_work+0xfe0/0xfe0
[69832.281414] kthread+0x32d/0x3f0
[69832.282082] ? kthread_park+0x170/0x170
[69832.282849] ret_from_fork+0x1f/0x30
[69832.283573]
[69832.283886] Allocated by task 7725:
[69832.284599] kasan_save_stack+0x19/0x40
[69832.285385] __kasan_kmalloc.constprop.2+0xc1/0xd0
[69832.286350] kmem_cache_alloc_node+0x13f/0x460
[69832.287237] bfq_get_queue+0x3d4/0x1140
[69832.287993] bfq_get_bfqq_handle_split+0x103/0x510
[69832.289015] bfq_init_rq+0x337/0x2d50
[69832.289749] bfq_insert_requests+0x304/0x4e10
[69832.290634] blk_mq_sched_insert_requests+0x13e/0x390
[69832.291629] blk_mq_flush_plug_list+0x4b4/0x760
[69832.292538] blk_flush_plug_list+0x2c5/0x480
[69832.293392] io_schedule_prepare+0xb2/0xd0
[69832.294209] io_schedule_timeout+0x13/0x80
[69832.295014] wait_for_common_io.constprop.1+0x13c/0x270
[69832.296137] submit_bio_wait+0x103/0x1a0
[69832.296932] blkdev_issue_discard+0xe6/0x160
[69832.297794] blk_ioctl_discard+0x219/0x290
[69832.298614] blkdev_common_ioctl+0x50a/0x1750
[69832.304715] blkdev_ioctl+0x470/0x600
[69832.305474] block_ioctl+0xde/0x120
[69832.306232] vfs_ioctl+0x6c/0xc0
[69832.306877] __se_sys_ioctl+0x90/0xa0
[69832.307629] do_syscall_64+0x2d/0x40
[69832.308362] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[69832.309382]
[69832.309701] Freed by task 155:
[69832.310328] kasan_save_stack+0x19/0x40
[69832.311121] kasan_set_track+0x1c/0x30
[69832.311868] kasan_set_free_info+0x1b/0x30
[69832.312699] __kasan_slab_free+0x111/0x160
[69832.313524] kmem_cache_free+0x94/0x460
[69832.314367] bfq_put_queue+0x582/0x940
[69832.315112] __bfq_bfqd_reset_in_service+0x166/0x1d0
[69832.317275] bfq_bfqq_expire+0xb27/0x2440
[69832.318084] bfq_dispatch_request+0x697/0x44b0
[69832.318991] __blk_mq_do_dispatch_sched+0x52f/0x830
[69832.319984] __blk_mq_sched_dispatch_requests+0x398/0x4f0
[69832.321087] blk_mq_sched_dispatch_requests+0xdf/0x140
[69832.322225] __blk_mq_run_hw_queue+0xc0/0x270
[69832.323114] blk_mq_run_work_fn+0x51/0x60
[69832.323942] process_one_work+0x6d4/0xfe0
[69832.324772] worker_thread+0x91/0xc80
[69832.325518] kthread+0x32d/0x3f0
[69832.326205] ret_from_fork+0x1f/0x30
[69832.326932]
[69832.338297] The buggy address belongs to the object at ffff88802622b968
[69832.338297] which belongs to the cache bfq_queue of size 512
[69832.340766] The buggy address is located 288 bytes inside of
[69832.340766] 512-byte region [ffff88802622b968, ffff88802622bb68)
[69832.343091] The buggy address belongs to the page:
[69832.344097] page:ffffea0000988a00 refcount:1 mapcount:0 mapping:0000000000000000 index:0xffff88802622a528 pfn:0x26228
[69832.346214] head:ffffea0000988a00 order:2 compound_mapcount:0 compound_pincount:0
[69832.347719] flags: 0x1fffff80010200(slab|head)
[69832.348625] raw: 001fffff80010200 ffffea0000dbac08 ffff888017a57650 ffff8880179fe840
[69832.354972] raw: ffff88802622a528 0000000000120008 00000001ffffffff 0000000000000000
[69832.356547] page dumped because: kasan: bad access detected
[69832.357652]
[69832.357970] Memory state around the buggy address:
[69832.358926] ffff88802622b980: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[69832.360358] ffff88802622ba00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[69832.361810] >ffff88802622ba80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[69832.363273] ^
[69832.363975] ffff88802622bb00: fb fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc
[69832.375960] ffff88802622bb80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[69832.377405] ==================================================================
In bfq_dispatch_requestfunction, it may have function call:
bfq_dispatch_request
__bfq_dispatch_request
bfq_select_queue
bfq_bfqq_expire
__bfq_bfqd_reset_in_service
bfq_put_queue
kmem_cache_free
In this function call, in_serv_queue has beed expired and meet the
conditions to free. In the function bfq_dispatch_request, the address
of in_serv_queue pointing to has been released. For getting the value
of idle_timer_disabled, it will get flags value from the address which
in_serv_queue pointing to, then the problem of use-after-free happens;
Fix the problem by check in_serv_queue == bfqd->in_service_queue, to
get the value of idle_timer_disabled if in_serve_queue is equel to
bfqd->in_service_queue. If the space of in_serv_queue pointing has
been released, this judge will aviod use-after-free problem.
And if in_serv_queue may be expired or finished, the idle_timer_disabled
will be false which would not give effects to bfq_update_dispatch_stats.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Wensheng <zhangwensheng5@huawei.com>
Link: https://lore.kernel.org/r/20220303070334.3020168-1-zhangwensheng5@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0da1d50027 ]
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=197921
As pointed out in the discussion of buglink, we cannot calculate AT_PHDR
as the sum of load_addr and exec->e_phoff.
: The AT_PHDR of ELF auxiliary vectors should point to the memory address
: of program header. But binfmt_elf.c calculates this address as follows:
:
: NEW_AUX_ENT(AT_PHDR, load_addr + exec->e_phoff);
:
: which is wrong since e_phoff is the file offset of program header and
: load_addr is the memory base address from PT_LOAD entry.
:
: The ld.so uses AT_PHDR as the memory address of program header. In normal
: case, since the e_phoff is usually 64 and in the first PT_LOAD region, it
: is the correct program header address.
:
: But if the address of program header isn't equal to the first PT_LOAD
: address + e_phoff (e.g. Put the program header in other non-consecutive
: PT_LOAD region), ld.so will try to read program header from wrong address
: then crash or use incorrect program header.
This is because exec->e_phoff
is the offset of PHDRs in the file and the address of PHDRs in the
memory may differ from it. This patch fixes the bug by calculating the
address of program headers from PT_LOADs directly.
Signed-off-by: Akira Kawata <akirakawata1@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20220127124014.338760-2-akirakawata1@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6aca2f460 ]
pdc_enable_intr() serves as a primitive to qcom_pdc_gic_{en,dis}able,
and has a raw spinlock for mutual exclusion, which is uses with
interruptible primitives.
This means that this critical section can itself be interrupted.
Should the interrupt also be a PDC interrupt, and the endpoint driver
perform an irq_disable() on that interrupt, we end-up in a deadlock.
Fix this by using the irqsave/irqrestore variants of the locking
primitives.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Maulik Shah <quic_mkshah@quicinc.com>
Link: https://lore.kernel.org/r/20220224101226.88373-5-maz@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5cd1ab7ab ]
Remove inappropriate use of ntohs() and assign the
port value directly.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b27824d31f ]
sprintf does not know the PAGE_SIZE maximum of the temporary buffer
used for outputting sysfs content and it's possible to overrun the
PAGE_SIZE buffer length.
Use a generic sysfs_emit function that knows the size of the
temporary buffer and ensures that no overrun is done for offset
attribute in
loop_attr_[offset|sizelimit|autoclear|partscan|dio]_show() callbacks.
Signed-off-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Link: https://lore.kernel.org/r/20220215213310.7264-2-kch@nvidia.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65881e1db4 ]
These ioctls are equivalent to fcntl(fd, F_SETFD, flags), which SELinux
always allows too. Furthermore, a failed FIOCLEX could result in a file
descriptor being leaked to a process that should not have access to it.
As this patch removes access controls, a policy capability needs to be
enabled in policy to always allow these ioctls.
Based-on-patch-by: Demi Marie Obenour <demiobenour@gmail.com>
Signed-off-by: Richard Haines <richard_c_haines@btinternet.com>
[PM: subject line tweak]
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b97df7c098 ]
security_sid_to_context() expects a pointer to an u32 as the address
where to store the length of the computed context.
Reported by sparse:
security/selinux/xfrm.c:359:39: warning: incorrect type in arg 4
(different signedness)
security/selinux/xfrm.c:359:39: expected unsigned int
[usertype] *scontext_len
security/selinux/xfrm.c:359:39: got int *
Signed-off-by: Christian Göttsche <cgzones@googlemail.com>
[PM: wrapped commit description]
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7e53e2255 ]
The npcm driver has a bunch of references to the irq_chip parent_device
field, but never sets it.
Fix it by fishing that reference from somewhere else, but it is
obvious that these debug statements were never used. Also remove
an unused field in a local data structure.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Bartosz Golaszewski <brgl@bgdev.pl>
Link: https://lore.kernel.org/r/20220201120310.878267-11-maz@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27e9faf415 ]
Since STRING_CST may not be NUL terminated, strncmp() was used for check
for equality. However, this may lead to mismatches for longer section
names where the start matches the tested-for string. Test for exact
equality by checking for the presences of NUL termination.
Cc: Alexander Popov <alex.popov@linux.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ecff30575b ]
The usual LSM hook "bail on fail" scheme doesn't work for cases where
a security module may return an error code indicating that it does not
recognize an input. In this particular case Smack sees a mount option
that it recognizes, and returns 0. A call to a BPF hook follows, which
returns -ENOPARAM, which confuses the caller because Smack has processed
its data.
The SELinux hook incorrectly returns 1 on success. There was a time
when this was correct, however the current expectation is that it
return 0 on success. This is repaired.
Reported-by: syzbot+d1e3b1d92d25abf97943@syzkaller.appspotmail.com
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Acked-by: James Morris <jamorris@linux.microsoft.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d888c83fce ]
Jason Donenfeld reports that my commit 1c24a18639 ("fs: fd tables have
to be multiples of BITS_PER_LONG") doesn't work, and the reason is an
embarrassing brown-paper-bag bug.
Yes, we want to align the number of fds to BITS_PER_LONG, and yes, the
reason they might not be aligned is because the incoming 'max_fd'
argument might not be aligned.
But aligining the argument - while simple - will cause a "infinitely
big" maxfd (eg NR_OPEN_MAX) to just overflow to zero. Which most
definitely isn't what we want either.
The obvious fix was always just to do the alignment last, but I had
moved it earlier just to make the patch smaller and the code look
simpler. Duh. It certainly made _me_ look simple.
Fixes: 1c24a18639 ("fs: fd tables have to be multiples of BITS_PER_LONG")
Reported-and-tested-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Fedor Pchelkin <aissur0002@gmail.com>
Cc: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: Christian Brauner <brauner@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc0ce6cc4b ]
The "test_dev" pointer is freed but then returned to the caller.
Fixes: d9c6a72d6f ("kmod: add test driver to stress test the module loader")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c24a18639 ]
This has always been the rule: fdtables have several bitmaps in them,
and as a result they have to be sized properly for bitmaps. We walk
those bitmaps in chunks of 'unsigned long' in serveral cases, but even
when we don't, we use the regular kernel bitops that are defined to work
on arrays of 'unsigned long', not on some byte array.
Now, the distinction between arrays of bytes and 'unsigned long'
normally only really ends up being noticeable on big-endian systems, but
Fedor Pchelkin and Alexey Khoroshilov reported that copy_fd_bitmaps()
could be called with an argument that wasn't even a multiple of
BITS_PER_BYTE. And then it fails to do the proper copy even on
little-endian machines.
The bug wasn't in copy_fd_bitmap(), but in sane_fdtable_size(), which
didn't actually sanitize the fdtable size sufficiently, and never made
sure it had the proper BITS_PER_LONG alignment.
That's partly because the alignment historically came not from having to
explicitly align things, but simply from previous fdtable sizes, and
from count_open_files(), which counts the file descriptors by walking
them one 'unsigned long' word at a time and thus naturally ends up doing
sizing in the proper 'chunks of unsigned long'.
But with the introduction of close_range(), we now have an external
source of "this is how many files we want to have", and so
sane_fdtable_size() needs to do a better job.
This also adds that explicit alignment to alloc_fdtable(), although
there it is mainly just for documentation at a source code level. The
arithmetic we do there to pick a reasonable fdtable size already aligns
the result sufficiently.
In fact,clang notices that the added ALIGN() in that function doesn't
actually do anything, and does not generate any extra code for it.
It turns out that gcc ends up confusing itself by combining a previous
constant-sized shift operation with the variable-sized shift operations
in roundup_pow_of_two(). And probably due to that doesn't notice that
the ALIGN() is a no-op. But that's a (tiny) gcc misfeature that doesn't
matter. Having the explicit alignment makes sense, and would actually
matter on a 128-bit architecture if we ever go there.
This also adds big comments above both functions about how fdtable sizes
have to have that BITS_PER_LONG alignment.
Fixes: 60997c3d45 ("close_range: add CLOSE_RANGE_UNSHARE")
Reported-by: Fedor Pchelkin <aissur0002@gmail.com>
Reported-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Link: https://lore.kernel.org/all/20220326114009.1690-1-aissur0002@gmail.com/
Tested-and-acked-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c9d845f06 ]
In nfs4_callback_devicenotify(), if we don't find a matching entry for
the deviceid, we're left with a pointer to 'struct nfs_server' that
actually points to the list of super blocks associated with our struct
nfs_client.
Furthermore, even if we have a valid pointer, nothing pins the super
block, and so the struct nfs_server could end up getting freed while
we're using it.
Since all we want is a pointer to the struct pnfs_layoutdriver_type,
let's skip all the iteration over super blocks, and just use APIs to
find the layout driver directly.
Reported-by: Xiaomeng Tong <xiam0nd.tong@gmail.com>
Fixes: 1be5683b03 ("pnfs: CB_NOTIFY_DEVICEID")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7781607938 ]
When the link layer is terminating, x25->neighbour will be set to NULL
in x25_disconnect(). As a result, it could cause null-ptr-deref bugs in
x25_sendmsg(),x25_recvmsg() and x25_connect(). One of the bugs is
shown below.
(Thread 1) | (Thread 2)
x25_link_terminated() | x25_recvmsg()
x25_kill_by_neigh() | ...
x25_disconnect() | lock_sock(sk)
... | ...
x25->neighbour = NULL //(1) |
... | x25->neighbour->extended //(2)
The code sets NULL to x25->neighbour in position (1) and dereferences
x25->neighbour in position (2), which could cause null-ptr-deref bug.
This patch adds lock_sock() in x25_kill_by_neigh() in order to synchronize
with x25_sendmsg(), x25_recvmsg() and x25_connect(). What`s more, the
sock held by lock_sock() is not NULL, because it is extracted from x25_list
and uses x25_list_lock to synchronize.
Fixes: 4becb7ee5b ("net/x25: Fix x25_neigh refcnt leak when x25 disconnect")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1521db37f0 ]
Clang static analysis reports this issue
qlcnic_dcb.c:382:10: warning: Assigned value is
garbage or undefined
mbx_out = *val;
^ ~~~~
val is set in the qlcnic_dcb_query_hw_capability() wrapper.
If there is no query_hw_capability op in dcp, success is
returned without setting the val.
For this and similar wrappers, return -EOPNOTSUPP.
Fixes: 14d385b990 ("qlcnic: dcb: Query adapter DCB capabilities.")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b50d3b46f8 ]
The purpose of the last test case is to test VXLAN encapsulation and
decapsulation when the underlay lookup takes place in a non-default VRF.
This is achieved by enslaving the physical device of the tunnel to a
VRF.
The binding of the VXLAN UDP socket to the VRF happens when the VXLAN
device itself is opened, not when its physical device is opened. This
was also mentioned in the cited commit ("tests that moving the underlay
from a VRF to another works when down/up the VXLAN interface"), but the
test did something else.
Fix it by reopening the VXLAN device instead of its physical device.
Before:
# ./test_vxlan_under_vrf.sh
Checking HV connectivity [ OK ]
Check VM connectivity through VXLAN (underlay in the default VRF) [ OK ]
Check VM connectivity through VXLAN (underlay in a VRF) [FAIL]
After:
# ./test_vxlan_under_vrf.sh
Checking HV connectivity [ OK ]
Check VM connectivity through VXLAN (underlay in the default VRF) [ OK ]
Check VM connectivity through VXLAN (underlay in a VRF) [ OK ]
Fixes: 03f1c26b1c ("test/net: Add script for VXLAN underlay in a VRF")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220324200514.1638326-1-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf8bfc4336 ]
A Broadcom AC201 PHY (same entry as 5241) would be flagged by the
Broadcom UniMAC MDIO controller as not completing the turn around
properly since the PHY expects 65 MDC clock cycles to complete a write
cycle, and the MDIO controller was only sending 64 MDC clock cycles as
determined by looking at a scope shot.
This would make the subsequent read fail with the UniMAC MDIO controller
command field having MDIO_READ_FAIL set and we would abort the
brcm_fet_config_init() function and thus not probe the PHY at all.
After issuing a software reset, wait for at least 1ms which is well
above the 1us reset delay advertised by the datasheet and issue a dummy
read to let the PHY turn around the line properly. This read
specifically ignores -EIO which would be returned by MDIO controllers
checking for the line being turned around.
If we have a genuine reaad failure, the next read of the interrupt
status register would pick it up anyway.
Fixes: d7a2ed9248 ("broadcom: Add AC131 phy support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220324232438.1156812-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ccb18f0553 ]
If the MAC address A is configured to vport A and then vport B. The MAC
address of vport A in the hardware becomes invalid. If the address of
vport A is changed to MAC address B, the driver needs to delete the MAC
address A of vport A. Due to the MAC address A of vport A has become
invalid in the hardware entry, so "-ENOENT" is returned. In this case, the
"used_umv_size" value recorded in driver is not updated. As a result, the
MAC entry status of the software is inconsistent with that of the hardware.
Therefore, the driver updates the umv size even if the MAC entry cannot be
found. Ensure that the software and hardware status is consistent.
Fixes: ee4bcd3b7a ("net: hns3: refactor the MAC address configure")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de2ae403b4 ]
is_xen_pmu() is taking the cpu number as parameter, but it is not using
it. Instead it just tests whether the Xen PMU initialization on the
current cpu did succeed. As this test is done by checking a percpu
pointer, preemption needs to be disabled in order to avoid switching
the cpu while doing the test. While resuming from suspend() this seems
not to be the case:
[ 88.082751] ACPI: PM: Low-level resume complete
[ 88.087933] ACPI: EC: EC started
[ 88.091464] ACPI: PM: Restoring platform NVS memory
[ 88.097166] xen_acpi_processor: Uploading Xen processor PM info
[ 88.103850] Enabling non-boot CPUs ...
[ 88.108128] installing Xen timer for CPU 1
[ 88.112763] BUG: using smp_processor_id() in preemptible [00000000] code: systemd-sleep/7138
[ 88.122256] caller is is_xen_pmu+0x12/0x30
[ 88.126937] CPU: 0 PID: 7138 Comm: systemd-sleep Tainted: G W 5.16.13-2.fc32.qubes.x86_64 #1
[ 88.137939] Hardware name: Star Labs StarBook/StarBook, BIOS 7.97 03/21/2022
[ 88.145930] Call Trace:
[ 88.148757] <TASK>
[ 88.151193] dump_stack_lvl+0x48/0x5e
[ 88.155381] check_preemption_disabled+0xde/0xe0
[ 88.160641] is_xen_pmu+0x12/0x30
[ 88.164441] xen_smp_intr_init_pv+0x75/0x100
Fix that by replacing is_xen_pmu() by a simple boolean variable which
reflects the Xen PMU initialization state on cpu 0.
Modify xen_pmu_init() to return early in case it is being called for a
cpu other than cpu 0 and the boolean variable not being set.
Fixes: bf6dfb154d ("xen/PMU: PMU emulation code")
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20220325142002.31789-1-jgross@suse.com
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f7e2af008 ]
When registering a clock that doesn't have a recalc_rate implementation,
and doesn't have its parent registered yet, we initialize the clk_core
rate and 'req_rate' fields to 0.
The rate field is later updated when the parent is registered in
clk_core_reparent_orphans_nolock() using __clk_recalc_rates(), but the
'req_rate' field is never updated.
This leads to an issue in clk_set_rate_range() and clk_put(), since
those functions will call clk_set_rate() with the content of 'req_rate'
to provide drivers with the opportunity to change the rate based on the
new boundaries. In this case, we would call clk_set_rate() with a rate
of 0, effectively enforcing the minimum allowed for this clock whenever
we would call one of those two functions, even though the actual rate
might be within range.
Let's fix this by setting 'req_rate' in
clk_core_reparent_orphans_nolock() with the rate field content just
updated by the call to __clk_recalc_rates().
Fixes: 1c8e600440 ("clk: Add rate constraints to clocks")
Reported-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com> # T30 Nexus7
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220325161144.1901695-2-maxime@cerno.tech
[sboyd@kernel.org: Reword comment]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1cb81429d ]
Currently kdb_putarea_size() uses copy_from_kernel_nofault() to write *to*
arbitrary kernel memory. This is obviously wrong and means the memory
modify ('mm') command is a serious risk to debugger stability: if we poke
to a bad address we'll double-fault and lose our debug session.
Fix this the (very) obvious way.
Note that there are two Fixes: tags because the API was renamed and this
patch will only trivially backport as far as the rename (and this is
probably enough). Nevertheless Christoph's rename did not introduce this
problem so I wanted to record that!
Fixes: fe557319aa ("maccess: rename probe_kernel_{read,write} to copy_{from,to}_kernel_nofault")
Fixes: 5d5314d679 ("kdb: core for kgdb back end (1 of 2)")
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20220128144055.207267-1-daniel.thompson@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d15d121cc ]
There is no reason to retry the operation if a session error had
occurred in such case result structure isn't filled out.
Fixes: dff58530c4 ("NFSv4.1: fix handling of backchannel binding in BIND_CONN_TO_SESSION")
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2dd495a8d ]
Do not reset IP_CT_TCP_FLAG_BE_LIBERAL flag in out-of-sync scenarios
coming before the TCP window tracking, otherwise such connections will
fail in the window check.
Update tcp_options() to leave this flag in place and add a new helper
function to reset the tcp window state.
Based on patch from Sven Auhagen.
Fixes: c4832c7bbc ("netfilter: nf_ct_tcp: improve out-of-sync situation in TCP tracking")
Tested-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2cc7cc01c1 ]
Syzbot reported divide error in dbNextAG(). The problem was in missing
validation check for malicious image.
Syzbot crafted an image with bmp->db_numag equal to 0. There wasn't any
validation checks, but dbNextAG() blindly use bmp->db_numag in divide
expression
Fix it by validating bmp->db_numag in dbMount() and return an error if
image is malicious
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-and-tested-by: syzbot+46f5c25af73eb8330eb6@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37fd83916d ]
The Google Coreboot implementation requires IOMEM functions
(memmremap, memunmap, devm_memremap), but does not specify this is its
Kconfig. This results in build errors when HAS_IOMEM is not set, such as
on some UML configurations:
/usr/bin/ld: drivers/firmware/google/coreboot_table.o: in function `coreboot_table_probe':
coreboot_table.c:(.text+0x311): undefined reference to `memremap'
/usr/bin/ld: coreboot_table.c:(.text+0x34e): undefined reference to `memunmap'
/usr/bin/ld: drivers/firmware/google/memconsole-coreboot.o: in function `memconsole_probe':
memconsole-coreboot.c:(.text+0x12d): undefined reference to `memremap'
/usr/bin/ld: memconsole-coreboot.c:(.text+0x17e): undefined reference to `devm_memremap'
/usr/bin/ld: memconsole-coreboot.c:(.text+0x191): undefined reference to `memunmap'
/usr/bin/ld: drivers/firmware/google/vpd.o: in function `vpd_section_destroy.isra.0':
vpd.c:(.text+0x300): undefined reference to `memunmap'
/usr/bin/ld: drivers/firmware/google/vpd.o: in function `vpd_section_init':
vpd.c:(.text+0x382): undefined reference to `memremap'
/usr/bin/ld: vpd.c:(.text+0x459): undefined reference to `memunmap'
/usr/bin/ld: drivers/firmware/google/vpd.o: in function `vpd_probe':
vpd.c:(.text+0x59d): undefined reference to `memremap'
/usr/bin/ld: vpd.c:(.text+0x5d3): undefined reference to `memunmap'
collect2: error: ld returned 1 exit status
Fixes: a28aad66da ("firmware: coreboot: Collapse platform drivers into bus core")
Acked-By: anton ivanov <anton.ivanov@cambridgegreys.com>
Acked-By: Julius Werner <jwerner@chromium.org>
Signed-off-by: David Gow <davidgow@google.com>
Link: https://lore.kernel.org/r/20220225041502.1901806-1-davidgow@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f58c252e30 ]
When 8250 UART is using DMA, x_char (XON/XOFF) is never sent
to the wire. After this change, x_char is injected correctly.
Create uart_xchar_out() helper for sending the x_char out and
accounting related to it. It seems that almost every driver
does these same steps with x_char. Except for 8250, however,
almost all currently lack .serial_out so they cannot immediately
take advantage of this new helper.
The downside of this patch is that it might reintroduce
the problems some devices faced with mixed DMA/non-DMA transfer
which caused revert f967fc8f16 (Revert "serial: 8250_dma:
don't bother DMA with small transfers"). However, the impact
should be limited to cases with XON/XOFF (that didn't work
with DMA capable devices to begin with so this problem is not
very likely to cause a major issue, if any at all).
Fixes: 9ee4b83e51 ("serial: 8250: Add support for dmaengine")
Reported-by: Gilles Buloz <gilles.buloz@kontron.com>
Tested-by: Gilles Buloz <gilles.buloz@kontron.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220314091432.4288-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54fe55fb38 ]
mtk_pconf_group_get(), used to read back pingroup pin config state,
simply returns a set of configs saved from a previous invocation of
mtk_pconf_group_set(). This is an unfiltered, unvalidated set passed
in from the pinconf core, which does not match the current hardware
state.
Since the driver library is designed to have one pin per group, pass
through mtk_pconf_group_get() to mtk_pinconf_get(), to read back the
current pin config state of the only pin in the group.
Also drop the assignment of pin config state to the group.
Fixes: 805250982b ("pinctrl: mediatek: add pinctrl-paris that implements the vendor dt-bindings")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220308100956.2750295-5-wenst@chromium.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19bce7ce0a ]
For mtk_pinconf_get(), the "argument" argument is typically returned by
pinconf_to_config_argument(), which holds the value for a given pinconf
parameter. It certainly should not have the type of "enum pin_config_param",
which describes the type of the pinconf parameter itself.
Change the type to u32, which matches the return type of
pinconf_to_config_argument().
Fixes: 805250982b ("pinctrl: mediatek: add pinctrl-paris that implements the vendor dt-bindings")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220308100956.2750295-4-wenst@chromium.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6256e18686 ]
Fix LED and pinctrl definitions on the GB-PC1 devicetree. Refer to the
schematics of the device for more information.
LED fixes:
- Change GPIO6 LED label from system to power as GPIO6 is connected to
PLED.
- Add default-on default-trigger to power LED.
- Change GPIO8 LED label from status to system as GPIO8 is connected to
SYS_LED.
- Add disk-activity default-trigger to system LED.
- Switch to the color:function naming scheme.
- Remove lan1 and lan2 LEDs as they don't exist.
Pinctrl fixes:
- Claim state_default node under pinctrl node.
- Change pinctrl0 node name to state-default.
- Change gpio node name to gpio-pinmux to respect
Documentation/devicetree/bindings/pinctrl/ralink,rt2880-pinmux.yaml.
- Sort pin groups alphabetically.
Misc fixes:
- Fix formatting.
- Use the status value "okay".
- Define hexadecimal addresses in lower case.
- Make hexadecimal addresses for memory easier to read.
Link: https://github.com/ngiger/GnuBee_Docs/blob/master/GB-PCx/Documents/GB-PC1_V1.0_Schematic.pdf
Tested-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20220311090320.3068-1-arinc.unal@arinc9.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07a5dcc4be ]
The device_node pointer is returned by of_parse_phandle() or
of_get_child_by_name() with refcount incremented.
We should use of_node_put() on it when done.
This function only call of_node_put(node) when of_address_to_resource
succeeds, missing error cases.
Fixes: 278d744c46 ("remoteproc: qcom: Fix potential device node leaks")
Fixes: 051fb70fd4 ("remoteproc: qcom: Driver for the self-authenticating Hexagon v5")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220308064522.13804-1-linmq006@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b95044b384 ]
Remove the loaded hisi_dma driver and reload it, the driver fails
to work properly. The following error is reported in the kernel log:
[ 1475.597609] hisi_dma 0000:7b:00.0: Failed to allocate MSI vectors!
[ 1475.604915] hisi_dma: probe of 0000:7b:00.0 failed with error -28
As noted in "The MSI Driver Guide HOWTO"[1], the number of MSI
interrupt must be a power of two. The Kunpeng DMA driver allocates 30
MSI interrupts. As a result, no space left on device is reported
when the driver is reloaded and allocates interrupt vectors from the
interrupt domain.
This patch changes the number of interrupt vectors allocated by
hisi_dma driver to 32 to avoid this problem.
[1] https://www.kernel.org/doc/html/latest/PCI/msi-howto.html
Fixes: e9f08b6525 ("dmaengine: hisilicon: Add Kunpeng DMA engine support")
Signed-off-by: Jie Hai <haijie1@huawei.com>
Acked-by: Zhou Wang <wangzhou1@hisilicon.com>
Link: https://lore.kernel.org/r/20220216072101.34473-1-haijie1@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58922910ad ]
The display pixel clock has a requirement on certain newer platforms to
support M/N as (2/3) and the final D value calculated results in
underflow errors.
As the current implementation does not check for D value is within
the accepted range for a given M & N value. Update the logic to
calculate the final D value based on the range.
Fixes: 99cbd064b0 ("clk: qcom: Support display RCG clocks")
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220227175536.3131-1-tdas@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 80e4390981 ]
When valid kernel command line parameters
dma_debug=off dma_debug_entries=100
are used, they are reported as Unknown parameters and added to init's
environment strings, polluting it.
Unknown kernel command line parameters "BOOT_IMAGE=/boot/bzImage-517rc5
dma_debug=off dma_debug_entries=100", will be passed to user space.
and
Run /sbin/init as init process
with arguments:
/sbin/init
with environment:
HOME=/
TERM=linux
BOOT_IMAGE=/boot/bzImage-517rc5
dma_debug=off
dma_debug_entries=100
Return 1 from these __setup handlers to indicate that the command line
option has been handled.
Fixes: 59d3daafa1 ("dma-debug: add kernel command line parameters")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru>
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: iommu@lists.linux-foundation.org
Cc: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64cfca85ba ]
Valid return values for decode_dirent() callback functions are:
0: Success
-EBADCOOKIE: End of directory
-EAGAIN: End of xdr_stream
All errors need to map into one of those three values.
Fixes: 573c4e1ef5 ("NFS: Simplify ->decode_dirent() calling sequence")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c27896ac1 ]
As the potential failure of the pci_enable_device(),
it should be better to check the return value and return
error if fails.
Fixes: 70b2f993ea ("habanalabs: create common folder")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dedab69fd6 ]
Set em485->active_timer = NULL isn't always enough to take out the stop
timer. While there is a check that it acts in the right state (i.e.
waiting for RTS-after-send to pass after sending some chars) but the
following might happen:
- CPU1: some chars send, shifter becomes empty, stop tx timer armed
- CPU0: more chars send before RTS-after-send expired
- CPU0: shifter empty irq, port lock taken
- CPU1: tx timer triggers, waits for port lock
- CPU0: em485->active_timer = &em485->stop_tx_timer, hrtimer_start(),
releases lock()
- CPU1: get lock, see em485->active_timer == &em485->stop_tx_timer,
tear down RTS too early
This fix bases on research done by Steffen Trumtrar.
Fixes: b86f86e8e7 ("serial: 8250: fix potential deadlock in rs485-mode")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220215160236.344236-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c984083ec ]
The use of mapping_set_error() in conjunction with calls to
filemap_check_errors() is problematic because every error gets reported
as either an EIO or an ENOSPC by filemap_check_errors() in functions
such as filemap_write_and_wait() or filemap_write_and_wait_range().
In almost all cases, we prefer to use the more nuanced wb errors.
Fixes: b8946d7bfb ("NFS: Revalidate the file mapping on all fatal writeback errors")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3153fa38e3 ]
According to the comment of the function phy_mipi_dphy_get_default_config(),
it uses minimum D-PHY timings based on MIPI D-PHY specification. They are
derived from the valid ranges specified in Section 6.9, Table 14, Page 41
of the D-PHY specification (v1.2). The table 14 explicitly mentions that
the minimum T-LPX parameter is 50 nanoseconds and the minimum TA-SURE
parameter is T-LPX nanoseconds. Likewise, the kernel doc of the 'lpx' and
'ta_sure' members of struct phy_configure_opts_mipi_dphy mentions that
the minimum values are 50000 picoseconds and @lpx picoseconds respectively.
Also, the function phy_mipi_dphy_config_validate() checks if cfg->lpx is
less than 50000 picoseconds and if cfg->ta_sure is less than cfg->lpx,
which hints the same minimum values.
Without this patch, the function phy_mipi_dphy_get_default_config()
wrongly sets cfg->lpx to 60000 picoseconds and cfg->ta_sure to 2 * cfg->lpx.
So, let's correct them to 50000 picoseconds and cfg->lpx respectively.
Note that I've only tested the patch with RM67191 DSI panel on i.MX8mq EVK.
Help is needed to test with other i.MX8mq, Meson and Rockchip platforms,
as I don't have the hardwares.
Fixes: dddc97e823 ("phy: dphy: Add configuration helpers")
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Link: https://lore.kernel.org/r/20220216071257.1647703-1-victor.liu@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b77d8306d8 ]
Use floor ops on SDCC1 APPS clock in order to round down selected clock
frequency and avoid overclocking SD/eMMC cards.
For example, currently HS200 cards were failling tuning as they were
actually being clocked at 384MHz instead of 192MHz.
This caused some boards to disable 1.8V I/O and force the eMMC into the
standard HS mode (50MHz) and that appeared to work despite the eMMC being
overclocked to 96Mhz in that case.
There was a previous commit to use floor ops on SDCC clocks, but it looks
to have only covered SDCC2 clock.
Fixes: 9607f6224b ("clk: qcom: ipq8074: add PCIE, USB and SDCC clocks")
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220210173100.505128-1-robimarko@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de9b861018 ]
The checker failed to validate all enum IDs in the description of a
register with fixed-width register fields, due to a miscalculation of
the number of described states: each register field of n bits can have
"1 << n" possible states, not "1".
Increase SH_PFC_MAX_ENUMS accordingly, now more enum IDs are checked
(SH-Mobile AG5 has more than 4000 enum IDs defined).
Fixes: 12d057bad6 ("pinctrl: sh-pfc: checker: Add check for enum ID conflicts")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/6d8a6a05564f38f9d20464c1c17f96e52740cf6a.1645460429.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f281e4ddbb ]
The bit reversal was wrong for bits 1 and 3 of the 5 bits.
Result is driver failure to probe if you have more than 2 daisy-chained
devices. Discovered via QEMU based device emulation.
Fixes tag is for when this moved from a macro to a function, but it
was broken before that.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fixes: 065a7c0b1f ("Staging: iio: adc: ad7280a.c: Fixed Macro argument reuse")
Reviewed-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Link: https://lore.kernel.org/r/20220206190328.333093-2-jic23@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a47ac019e7 ]
The mma8452_driver declares both of_match_table and i2c_driver.id_table
match-tables, but its probe() function only checked for of matches.
Add support for i2c_device_id matches. This fixes the driver not loading
on some x86 tablets (e.g. the Nextbook Ares 8) where the i2c_client is
instantiated by platform code using an i2c_device_id.
Drop of_match_ptr() protection to avoid unused warning.
Fixes: c3cdd6e48e ("iio: mma8452: refactor for seperating chip specific data")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220208124336.511884-1-hdegoede@redhat.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a8a77abf0 ]
The fuse consists of 64 bits, with this statement we're supposed to get
the upper 32 bits but it actually read out of bounds and got 0 instead
of the desired value which lead to the "PVS bin not set." codepath being
run resetting our pvs value.
Fixes: a8811ec764 ("cpufreq: qcom: Add support for krait based socs")
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83ba7e895d ]
A struct device can never be devm_alloc()'ed.
Here, it is embedded in "struct fsi_master", and "struct fsi_master" is
embedded in "struct fsi_master_aspeed".
Since "struct device" is embedded, the data structure embedding it must be
released with the release function, as is already done here.
So use kzalloc() instead of devm_kzalloc() when allocating "aspeed" and
update all error handling branches accordingly.
This prevent a potential double free().
This also fix another issue if opb_readl() fails. Instead of a direct
return, it now jumps in the error handling path.
Fixes: 606397d67f ("fsi: Add ast2600 master driver")
Suggested-by: Greg KH <gregkh@linuxfoundation.org>
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/2c123f8b0a40dc1a061fae982169fe030b4f47e6.1641765339.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0401f24cd2 ]
When a driver calls pwmchip_add() it has to be prepared to immediately
get its callbacks called. So move allocation of driver data and hardware
initialization before the call to pwmchip_add().
This fixes a potential NULL pointer exception and a race condition on
register writes.
Fixes: 841e6f90bb ("pwm: NXP LPC18xx PWM/SCT driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd3a4907ee ]
When LSR is 0xff in ->activate() (rather unlike), we return an error.
Provided ->shutdown() is not called when ->activate() fails, nothing
actually frees the buffer in this case.
Fix this by properly freeing the buffer in a designated label. We jump
there also from the "!info->type" if now too.
Fixes: 6769140d30 ("tty: mxser: use the tty_port_open method")
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220124071430.14907-6-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a7d8cff4a ]
In the timer callback function tipc_sk_timeout(), we're trying to
reschedule another timeout to retransmit a setup request if destination
link is congested. But we use the incorrect timeout value
(msecs_to_jiffies(100)) instead of (jiffies + msecs_to_jiffies(100)),
so that the timer expires immediately, it's irrelevant for original
description.
In this commit we correct the timeout value in sk_reset_timer()
Fixes: 6787927475 ("tipc: buffer overflow handling in listener socket")
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Link: https://lore.kernel.org/r/20220321042229.314288-1-hoang.h.le@dektech.com.au
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60b44ca6bd ]
During NAT, a tuple collision may occur. When this happens, openvswitch
will make a second pass through NAT which will perform additional packet
modification. This will update the skb data, but not the flow key that
OVS uses. This means that future flow lookups, and packet matches will
have incorrect data. This has been supported since
5d50aa83e2 ("openvswitch: support asymmetric conntrack").
That commit failed to properly update the sw_flow_key attributes, since
it only called the ovs_ct_nat_update_key once, rather than each time
ovs_ct_nat_execute was called. As these two operations are linked, the
ovs_ct_nat_execute() function should always make sure that the
sw_flow_key is updated after a successful call through NAT infrastructure.
Fixes: 5d50aa83e2 ("openvswitch: support asymmetric conntrack")
Cc: Dumitru Ceara <dceara@redhat.com>
Cc: Numan Siddique <nusiddiq@redhat.com>
Signed-off-by: Aaron Conole <aconole@redhat.com>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://lore.kernel.org/r/20220318124319.3056455-1-aconole@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed0c99dc0f ]
tp->rx_opt.mss_clamp is not populated, yet, during TFO send so we
rise it to the local MSS. tp->mss_cache is not updated, however:
tcp_v6_connect():
tp->rx_opt.mss_clamp = IPV6_MIN_MTU - headers;
tcp_connect():
tcp_connect_init():
tp->mss_cache = min(mtu, tp->rx_opt.mss_clamp)
tcp_send_syn_data():
tp->rx_opt.mss_clamp = tp->advmss
After recent fixes to ICMPv6 PTB handling we started dropping
PMTU updates higher than tp->mss_cache. Because of the stale
tp->mss_cache value PMTU updates during TFO are always dropped.
Thanks to Wei for helping zero in on the problem and the fix!
Fixes: c7bb4b8903 ("ipv6: tcp: drop silly ICMPv6 packet too big messages")
Reported-by: Andre Nash <alnash@fb.com>
Reported-by: Neil Spring <ntspring@fb.com>
Reviewed-by: Wei Wang <weiwan@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20220321165957.1769954-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d3ea3d402 ]
GCC12 appears to be much smarter about its dependency tracking and is
aware that the relaxed variants are just normal loads and stores and
this is causing problems like:
[ 210.074549] ------------[ cut here ]------------
[ 210.079223] NETDEV WATCHDOG: enabcm6e4ei0 (bcmgenet): transmit queue 1 timed out
[ 210.086717] WARNING: CPU: 1 PID: 0 at net/sched/sch_generic.c:529 dev_watchdog+0x234/0x240
[ 210.095044] Modules linked in: genet(E) nft_fib_inet nft_fib_ipv4 nft_fib_ipv6 nft_fib nft_reject_inet nf_reject_ipv4 nf_reject_ipv6 nft_reject nft_ct nft_chain_nat]
[ 210.146561] ACPI CPPC: PCC check channel failed for ss: 0. ret=-110
[ 210.146927] CPU: 1 PID: 0 Comm: swapper/1 Tainted: G E 5.17.0-rc7G12+ #58
[ 210.153226] CPPC Cpufreq:cppc_scale_freq_workfn: failed to read perf counters
[ 210.161349] Hardware name: Raspberry Pi Foundation Raspberry Pi 4 Model B/Raspberry Pi 4 Model B, BIOS EDK2-DEV 02/08/2022
[ 210.161353] pstate: 80400005 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 210.161358] pc : dev_watchdog+0x234/0x240
[ 210.161364] lr : dev_watchdog+0x234/0x240
[ 210.161368] sp : ffff8000080a3a40
[ 210.161370] x29: ffff8000080a3a40 x28: ffffcd425af87000 x27: ffff8000080a3b20
[ 210.205150] x26: ffffcd425aa00000 x25: 0000000000000001 x24: ffffcd425af8ec08
[ 210.212321] x23: 0000000000000100 x22: ffffcd425af87000 x21: ffff55b142688000
[ 210.219491] x20: 0000000000000001 x19: ffff55b1426884c8 x18: ffffffffffffffff
[ 210.226661] x17: 64656d6974203120 x16: 0000000000000001 x15: 6d736e617274203a
[ 210.233831] x14: 2974656e65676d63 x13: ffffcd4259c300d8 x12: ffffcd425b07d5f0
[ 210.241001] x11: 00000000ffffffff x10: ffffcd425b07d5f0 x9 : ffffcd4258bdad9c
[ 210.248171] x8 : 00000000ffffdfff x7 : 000000000000003f x6 : 0000000000000000
[ 210.255341] x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000001000
[ 210.262511] x2 : 0000000000001000 x1 : 0000000000000005 x0 : 0000000000000044
[ 210.269682] Call trace:
[ 210.272133] dev_watchdog+0x234/0x240
[ 210.275811] call_timer_fn+0x3c/0x15c
[ 210.279489] __run_timers.part.0+0x288/0x310
[ 210.283777] run_timer_softirq+0x48/0x80
[ 210.287716] __do_softirq+0x128/0x360
[ 210.291392] __irq_exit_rcu+0x138/0x140
[ 210.295243] irq_exit_rcu+0x1c/0x30
[ 210.298745] el1_interrupt+0x38/0x54
[ 210.302334] el1h_64_irq_handler+0x18/0x24
[ 210.306445] el1h_64_irq+0x7c/0x80
[ 210.309857] arch_cpu_idle+0x18/0x2c
[ 210.313445] default_idle_call+0x4c/0x140
[ 210.317470] cpuidle_idle_call+0x14c/0x1a0
[ 210.321584] do_idle+0xb0/0x100
[ 210.324737] cpu_startup_entry+0x30/0x8c
[ 210.328675] secondary_start_kernel+0xe4/0x110
[ 210.333138] __secondary_switched+0x94/0x98
The assumption when these were relaxed seems to be that device memory
would be mapped non reordering, and that other constructs
(spinlocks/etc) would provide the barriers to assure that packet data
and in memory rings/queues were ordered with respect to device
register reads/writes. This itself seems a bit sketchy, but the real
problem with GCC12 is that it is moving the actual reads/writes around
at will as though they were independent operations when in truth they
are not, but the compiler can't know that. When looking at the
assembly dumps for many of these routines its possible to see very
clean, but not strictly in program order operations occurring as the
compiler would be free to do if these weren't actually register
reads/write operations.
Its possible to suppress the timeout with a liberal bit of dma_mb()'s
sprinkled around but the device still seems unable to reliably
send/receive data. A better plan is to use the safer readl/writel
everywhere.
Since this partially reverts an older commit, which notes the use of
the relaxed variants for performance reasons. I would suggest that
any performance problems with this commit are targeted at relaxing only
the performance critical code paths after assuring proper barriers.
Fixes: 69d2ea9c79 ("net: bcmgenet: Use correct I/O accessors")
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Acked-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220310045358.224350-1-jeremy.linton@arm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec80906b0f ]
When test_lirc_mode2_user exec failed, the test report failed but still
exit with 0. Fix it by exiting with an error code.
Another issue is for the LIRCDEV checking. With bash -n, we need to quote
the variable, or it will always be true. So if test_lirc_mode2_user was
not run, just exit with skip code.
Fixes: 6bdd533cee ("bpf: add selftest for lirc_mode2 type program")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20220321024149.157861-1-liuhangbin@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a22aabf20 ]
Attempting to rollback the activation of the current master when
the current master has not been activated is bad. priv->cur_chan
and priv->cur_adap are both still zeroed out and the rollback
may result in attempts to revert an of changeset that has not been
applied and do result in calls to both del and put the zeroed out
i2c_adapter. Maybe it crashes, or whatever, but it's bad in any
case.
Fixes: e9d1a0a41d ("i2c: mux: demux-pinctrl: Fix an error handling path in 'i2c_demux_pinctrl_probe()'")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb13aa16f3 ]
Having meson_i2c_set_clk_div after i2c_add_adapter
causes issues for client drivers that try to use
the bus before the requested speed is applied.
The bus can be used just after i2c_add_adapter, so
move i2c_add_adapter to the final step as
meson_i2c_set_clk_div needs to be called before
the bus is used.
Fixes: 09af1c2fa4 ("i2c: meson: set clock divider in probe instead of setting it for each transfer")
Signed-off-by: Lucas Tanure <tanure@linux.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0caf6d9922 ]
When a netlink message is received, netlink_recvmsg() fills in the address
of the sender. One of the fields is the 32-bit bitfield nl_groups, which
carries the multicast group on which the message was received. The least
significant bit corresponds to group 1, and therefore the highest group
that the field can represent is 32. Above that, the UB sanitizer flags the
out-of-bounds shift attempts.
Which bits end up being set in such case is implementation defined, but
it's either going to be a wrong non-zero value, or zero, which is at least
not misleading. Make the latter choice deterministic by always setting to 0
for higher-numbered multicast groups.
To get information about membership in groups >= 32, userspace is expected
to use nl_pktinfo control messages[0], which are enabled by NETLINK_PKTINFO
socket option.
[0] https://lwn.net/Articles/147608/
The way to trigger this issue is e.g. through monitoring the BRVLAN group:
# bridge monitor vlan &
# ip link add name br type bridge
Which produces the following citation:
UBSAN: shift-out-of-bounds in net/netlink/af_netlink.c:162:19
shift exponent 32 is too large for 32-bit type 'int'
Fixes: f7fa9b10ed ("[NETLINK]: Support dynamic number of multicast groups per netlink family")
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/2bef6aabf201d1fc16cca139a744700cff9dcb04.1647527635.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 544b4dd568 ]
The PMTU update and ICMP redirect helper functions initialise their fl4
variable with either __build_flow_key() or build_sk_flow_key(). These
initialisation functions always set ->flowi4_scope with
RT_SCOPE_UNIVERSE and might set the ECN bits of ->flowi4_tos. This is
not a problem when the route lookup is later done via
ip_route_output_key_hash(), which properly clears the ECN bits from
->flowi4_tos and initialises ->flowi4_scope based on the RTO_ONLINK
flag. However, some helpers call fib_lookup() directly, without
sanitising the tos and scope fields, so the route lookup can fail and,
as a result, the ICMP redirect or PMTU update aren't taken into
account.
Fix this by extracting the ->flowi4_tos and ->flowi4_scope sanitisation
code into ip_rt_fix_tos(), then use this function in handlers that call
fib_lookup() directly.
Note 1: We can't sanitise ->flowi4_tos and ->flowi4_scope in a central
place (like __build_flow_key() or flowi4_init_output()), because
ip_route_output_key_hash() expects non-sanitised values. When called
with sanitised values, it can erroneously overwrite RT_SCOPE_LINK with
RT_SCOPE_UNIVERSE in ->flowi4_scope. Therefore we have to be careful to
sanitise the values only for those paths that don't call
ip_route_output_key_hash().
Note 2: The problem is mostly about sanitising ->flowi4_tos. Having
->flowi4_scope initialised with RT_SCOPE_UNIVERSE instead of
RT_SCOPE_LINK probably wasn't really a problem: sockets with the
SOCK_LOCALROUTE flag set (those that'd result in RTO_ONLINK being set)
normally shouldn't receive ICMP redirects or PMTU updates.
Fixes: 4895c771c7 ("ipv4: Add FIB nexthop exceptions.")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b062a0b9c1 ]
Fix the following kernel oops in btmtksdio_interrrupt
[ 14.339134] btmtksdio_interrupt+0x28/0x54
[ 14.339139] process_sdio_pending_irqs+0x68/0x1a0
[ 14.339144] sdio_irq_work+0x40/0x70
[ 14.339154] process_one_work+0x184/0x39c
[ 14.339160] worker_thread+0x228/0x3e8
[ 14.339168] kthread+0x148/0x3ac
[ 14.339176] ret_from_fork+0x10/0x30
That happened because hdev->power_on is already called before
sdio_set_drvdata which btmtksdio_interrupt handler relies on is not
properly set up.
The details are shown as the below: hci_register_dev would run
queue_work(hdev->req_workqueue, &hdev->power_on) as WQ_HIGHPRI
workqueue_struct to complete the power-on sequeunce and thus hci_power_on
may run before sdio_set_drvdata is done in btmtksdio_probe.
The hci_dev_do_open in hci_power_on would initialize the device and enable
the interrupt and thus it is possible that btmtksdio_interrupt is being
called right before sdio_set_drvdata is filled out.
When btmtksdio_interrupt is being called and sdio_set_drvdata is not filled
, the kernel oops is going to happen because btmtksdio_interrupt access an
uninitialized pointer.
Fixes: 9aebfd4a22 ("Bluetooth: mediatek: add support for MediaTek MT7663S and MT7668S SDIO devices")
Reviewed-by: Mark Chen <markyawenchen@gmail.com>
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9fa6b4cda3 ]
hci_le_conn_failed function's documentation says that the caller must
hold hdev->lock. The only callsite that does not hold that lock is
hci_le_conn_failed. The other 3 callsites hold the hdev->lock very
locally. The solution is to hold the lock during the call to
hci_le_conn_failed.
Fixes: 3c857757ef ("Bluetooth: Add directed advertising support through connect()")
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a4c9fe0ed4 ]
The helper macro that records an error in BPF programs that exercise sock
fields access has been inadvertently broken by adaptation work that
happened in commit b18c1f0aa4 ("bpf: selftest: Adapt sock_fields test to
use skel and global variables").
BPF_NOEXIST flag cannot be used to update BPF_MAP_TYPE_ARRAY. The operation
always fails with -EEXIST, which in turn means the error never gets
recorded, and the checks for errors always pass.
Revert the change in update flags.
Fixes: b18c1f0aa4 ("bpf: selftest: Adapt sock_fields test to use skel and global variables")
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20220317113920.1068535-2-jakub@cloudflare.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e077ed58c2 ]
bareudp_create_sock() use AF_INET6 by default if IPv6 CONFIG enabled.
But if user start kernel with ipv6.disable=1, the bareudp sock will
created failed, which cause the interface open failed even with ethertype
ip. e.g.
# ip link add bareudp1 type bareudp dstport 2 ethertype ip
# ip link set bareudp1 up
RTNETLINK answers: Address family not supported by protocol
Fix it by using ipv6_mod_enabled() to check if IPv6 enabled. There is
no need to check IS_ENABLED(CONFIG_IPV6) as ipv6_mod_enabled() will
return false when CONFIG_IPV6 no enabled in include/linux/ipv6.h.
Reported-by: Jianlin Shi <jishi@redhat.com>
Fixes: 571912c69f ("net: UDP tunnel encapsulation module for tunnelling different protocols like MPLS, IP, NSH etc.")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://lore.kernel.org/r/20220315062618.156230-1-liuhangbin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8fa42d78f6 ]
When running xdpsock for a fix duration of time before terminating
using --duration=<n>, there is a race condition that may cause xdpsock
to terminate immediately.
When running for a fixed duration of time the check to determine when to
terminate execution is in is_benchmark_done() and is being executed in
the context of the poller thread,
if (opt_duration > 0) {
unsigned long dt = (get_nsecs() - start_time);
if (dt >= opt_duration)
benchmark_done = true;
}
However start_time is only set after the poller thread have been
created. This leaves a small window when the poller thread is starting
and calls is_benchmark_done() for the first time that start_time is not
yet set. In that case start_time have its initial value of 0 and the
duration check fails as it do not correlate correctly for the
applications start time and immediately sets benchmark_done which in
turn terminates the xdpsock application.
Fix this by setting start_time before creating the poller thread.
Fixes: d3f11b018f ("samples/bpf: xdpsock: Add duration option to specify how long to run")
Signed-off-by: Niklas Söderlund <niklas.soderlund@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20220315102948.466436-1-niklas.soderlund@corigine.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2486ab434b ]
If tcp_bpf_sendmsg is running during a tear down operation, psock may be
freed.
tcp_bpf_sendmsg()
tcp_bpf_send_verdict()
sk_msg_return()
tcp_bpf_sendmsg_redir()
unlikely(!psock))
sk_msg_free()
The mem of msg has been uncharged in tcp_bpf_send_verdict() by
sk_msg_return(), and would be uncharged by sk_msg_free() again. When psock
is null, we can simply returning an error code, this would then trigger
the sk_msg_free_nocharge in the error path of __SK_REDIRECT and would have
the side effect of throwing an error up to user space. This would be a
slight change in behavior from user side but would look the same as an
error if the redirect on the socket threw an error.
This issue can cause the following info:
WARNING: CPU: 0 PID: 2136 at net/ipv4/af_inet.c:155 inet_sock_destruct+0x13c/0x260
Call Trace:
<TASK>
__sk_destruct+0x24/0x1f0
sk_psock_destroy+0x19b/0x1c0
process_one_work+0x1b3/0x3c0
worker_thread+0x30/0x350
? process_one_work+0x3c0/0x3c0
kthread+0xe6/0x110
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x22/0x30
</TASK>
Fixes: 604326b41a ("bpf, sockmap: convert to generic sk_msg interface")
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20220304081145.2037182-5-wangyufen@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c34e38c4a ]
If tcp_bpf_sendmsg() is running while sk msg is full. When sk_msg_alloc()
returns -ENOMEM error, tcp_bpf_sendmsg() goes to wait_for_memory. If partial
memory has been alloced by sk_msg_alloc(), that is, msg_tx->sg.size is
greater than osize after sk_msg_alloc(), memleak occurs. To fix we use
sk_msg_trim() to release the allocated memory, then goto wait for memory.
Other call paths of sk_msg_alloc() have the similar issue, such as
tls_sw_sendmsg(), so handle sk_msg_trim logic inside sk_msg_alloc(),
as Cong Wang suggested.
This issue can cause the following info:
WARNING: CPU: 3 PID: 7950 at net/core/stream.c:208 sk_stream_kill_queues+0xd4/0x1a0
Call Trace:
<TASK>
inet_csk_destroy_sock+0x55/0x110
__tcp_close+0x279/0x470
tcp_close+0x1f/0x60
inet_release+0x3f/0x80
__sock_release+0x3d/0xb0
sock_close+0x11/0x20
__fput+0x92/0x250
task_work_run+0x6a/0xa0
do_exit+0x33b/0xb60
do_group_exit+0x2f/0xa0
get_signal+0xb6/0x950
arch_do_signal_or_restart+0xac/0x2a0
exit_to_user_mode_prepare+0xa9/0x200
syscall_exit_to_user_mode+0x12/0x30
do_syscall_64+0x46/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
</TASK>
WARNING: CPU: 3 PID: 2094 at net/ipv4/af_inet.c:155 inet_sock_destruct+0x13c/0x260
Call Trace:
<TASK>
__sk_destruct+0x24/0x1f0
sk_psock_destroy+0x19b/0x1c0
process_one_work+0x1b3/0x3c0
kthread+0xe6/0x110
ret_from_fork+0x22/0x30
</TASK>
Fixes: 604326b41a ("bpf, sockmap: convert to generic sk_msg interface")
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20220304081145.2037182-3-wangyufen@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2bc5bab9a7 ]
pgd page is freed by generic implementation pgd_free() since commit
f9cb654cb5 ("asm-generic: pgalloc: provide generic pgd_free()"),
however, there are scenarios that the system uses more than one page as
the pgd table, in such cases the generic implementation pgd_free() won't
be applicable anymore. For example, when PAGE_SIZE_4KB is enabled and
MIPS_VA_BITS_48 is not enabled in a 64bit system, the macro "PGD_ORDER"
will be set as "1", which will cause allocating two pages as the pgd
table. Well, at the same time, the generic implementation pgd_free()
just free one pgd page, which will result in the memory leak.
The memory leak can be easily detected by executing shell command:
"while true; do ls > /dev/null; grep MemFree /proc/meminfo; done"
Fixes: f9cb654cb5 ("asm-generic: pgalloc: provide generic pgd_free()")
Signed-off-by: Yaliang Wang <Yaliang.Wang@windriver.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4528668ca3 ]
The of_find_compatible_node() function returns a node pointer with
refcount incremented, We should use of_node_put() on it when done
Add the missing of_node_put() to release the refcount.
Fixes: 2121aa3e23 ("mips: cdmm: Add mti,mips-cdmm dtb node support")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 259bdba27e ]
The vxcan driver provides a pair of virtual CAN interfaces to exchange
CAN traffic between different namespaces - analogue to veth.
In opposite to the vcan driver the local sent CAN traffic on this interface
is not echo'ed back but only sent to the remote peer. This is unusual and
can be easily fixed by removing IFF_ECHO from the netdevice flags that
are set for vxcan interfaces by default at startup.
Without IFF_ECHO set on driver level, the local sent CAN frames are echo'ed
in af_can.c in can_send(). This patch makes vxcan interfaces adopt the
same local echo behavior and procedures as known from the vcan interfaces.
Fixes: a8f820a380 ("can: add Virtual CAN Tunnel driver (vxcan)")
Link: https://lore.kernel.org/all/20220309120416.83514-5-socketcan@hartkopp.net
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d23a872032 ]
In test_lwt_ip_encap, the ingress IPv6 encap test failed from time to
time. The failure occured when an IPv4 ping through the IPv6 GRE
encapsulation did not receive a reply within the timeout. The IPv4 ping
and the IPv6 ping in the test used different timeouts (1 sec for IPv4
and 6 sec for IPv6), probably taking into account that IPv6 might need
longer to successfully complete. However, when IPv4 pings (with the
short timeout) are encapsulated into the IPv6 tunnel, the delays of IPv6
apply.
The actual reason for the long delays with IPv6 was that the IPv6
neighbor discovery sometimes did not complete in time. This was caused
by the outgoing interface only having a tentative link local address,
i.e., not having completed DAD for that lladdr. The ND was successfully
retried after 1 sec but that was too late for the ping timeout.
The IPv6 addresses for the test were already added with nodad. However,
for the lladdrs, DAD was still performed. We now disable DAD in the test
netns completely and just assume that the two lladdrs on each veth pair
do not collide. This removes all the delays for IPv6 traffic in the
test.
Without the delays, we can now also reduce the delay of the IPv6 ping to
1 sec. This makes the whole test complete faster because we don't need
to wait for the excessive timeout for each IPv6 ping that is supposed
to fail.
Fixes: 0fde56e438 ("selftests: bpf: add test_lwt_ip_encap selftest")
Signed-off-by: Felix Maurer <fmaurer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/4987d549d48b4e316cd5b3936de69c8d4bc75a4f.1646305899.git.fmaurer@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c6e6a80ee ]
xsk_umem__create() does mmap for fill/comp rings, but xsk_umem__delete()
doesn't do the unmap. This works fine for regular cases, because
xsk_socket__delete() does unmap for the rings. But for the case that
xsk_socket__create_shared() fails, umem rings are not unmapped.
fill_save/comp_save are checked to determine if rings have already be
unmapped by xsk. If fill_save and comp_save are NULL, it means that the
rings have already been used by xsk. Then they are supposed to be
unmapped by xsk_socket__delete(). Otherwise, xsk_umem__delete() does the
unmap.
Fixes: 2f6324a393 ("libbpf: Support shared umems between queues and devices")
Signed-off-by: Cheng Li <lic121@chinatelecom.cn>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20220301132623.GA19995@vscode.7~
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a7d340ba4 ]
If a memory allocation error occurred during an attempt to refill a slot
in the RX ring after the packet was received, the hardware tail pointer
would still have been updated to point to or past the slot which remained
marked as previously completed. This would likely result in the DMA engine
raising an error when it eventually tried to use that slot again.
If a slot cannot be refilled, then just stop processing and do not move
the tail pointer past it. On the next attempt, we should skip receiving
the packet from the empty slot and just try to refill it again.
This failure mode has not actually been observed, but was found as part
of other driver updates.
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92c45b63ce ]
For hardware that only supports 32-bit writes to PCI there is the
possibility of clearing RW1C (write-one-to-clear) bits. A rate-limited
messages was introduced by fb26592301, but rate-limiting is not the best
choice here. Some devices may not show the warnings they should if another
device has just produced a bunch of warnings. Also, the number of messages
can be a nuisance on devices which are otherwise working fine.
Change the ratelimit to a single warning per bus. This ensures no bus is
'starved' of emitting a warning and also that there isn't a continuous
stream of warnings. It would be preferable to have a warning per device,
but the pci_dev structure is not available here, and a lookup from devfn
would be far too slow.
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Fixes: fb26592301 ("PCI: Warn on possible RW1C corruption for sub-32 bit config writes")
Link: https://lore.kernel.org/r/20200806041455.11070-1-mark.tomlinson@alliedtelesis.co.nz
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0b14b5ba1 ]
As the potential failure of the wm8350_register_irq(),
it should be better to check it and return error if fails.
Also, use 'free_' in order to avoid same code.
Fixes: 14431aa0c5 ("power_supply: Add support for WM8350 PMU")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d366c2f9d ]
This driver is for an FPGA logic core, so there can be arbitrarily many
instances of the bus on a given system. Previously all of the I2C bus
names were "xiic-i2c" which caused issues with lm_sensors when trying to
map human-readable names to sensor inputs because it could not properly
distinguish the busses, for example. Append the platform device name to
the I2C bus name so it is unique between different instances.
Fixes: e1d5b6598c ("i2c: Add support for Xilinx XPS IIC Bus Interface")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d7286729a ]
For a couple of times I have encountered a situation where
hv_balloon: Unhandled message: type: 12447
is being flooded over 1 million times per second with various values,
filling the log and consuming cycles, making debugging difficult.
Add rate limiting to the message.
Most other Hyper-V drivers already have similar rate limiting in their
message callbacks.
The cause of the floods in my case was probably fixed by 96d9d1fa5c
("Drivers: hv: balloon: account for vmbus packet header in
max_pkt_size").
Fixes: 9aa8b50b2b ("Drivers: hv: Add Hyper-V balloon driver")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20220222141400.98160-1-anssi.hannula@bitwise.fi
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca85f00225 ]
Per Intel's SDM on the "Instruction Set Reference", when
loading segment descriptor, not-present segment check should
be after all type and privilege checks. But the emulator checks
it first, then #NP is triggered instead of #GP if privilege fails
and segment is not present. Put not-present segment check after
type and privilege checks in __load_segment_descriptor().
Fixes: 38ba30ba51 (KVM: x86 emulator: Emulate task switch in emulator.c)
Reviewed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Hou Wenlong <houwenlong.hwl@antgroup.com>
Message-Id: <52573c01d369f506cadcf7233812427cf7db81a7.1644292363.git.houwenlong.hwl@antgroup.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f66af9f222 ]
In emulation of writing to cr8, one of the lowest four bits in TPR[3:0]
is kept.
According to Intel SDM 10.8.6.1(baremetal scenario):
"APIC.TPR[bits 7:4] = CR8[bits 3:0], APIC.TPR[bits 3:0] = 0";
and SDM 28.3(use TPR shadow):
"MOV to CR8. The instruction stores bits 3:0 of its source operand into
bits 7:4 of VTPR; the remainder of VTPR (bits 3:0 and bits 31:8) are
cleared.";
and AMD's APM 16.6.4:
"Task Priority Sub-class (TPS)-Bits 3 : 0. The TPS field indicates the
current sub-priority to be used when arbitrating lowest-priority messages.
This field is written with zero when TPR is written using the architectural
CR8 register.";
so in KVM emulated scenario, clear TPR[3:0] to make a consistent behavior
as in other scenarios.
This doesn't impact evaluation and delivery of pending virtual interrupts
because processor does not use the processor-priority sub-class to
determine which interrupts to delivery and which to inhibit.
Sub-class is used by hardware to arbitrate lowest priority interrupts,
but KVM just does a round-robin style delivery.
Fixes: b93463aa59 ("KVM: Accelerated apic support")
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220210094506.20181-1-zhenzhong.duan@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2863dd2db2 ]
When CONFIG_GENERIC_CPU=y (true for all our defconfigs) we pass
-mcpu=powerpc64 to the compiler, even when we're building a 32-bit
kernel.
This happens because we have an ifdef CONFIG_PPC_BOOK3S_64/else block in
the Makefile that was written before 32-bit supported GENERIC_CPU. Prior
to that the else block only applied to 64-bit Book3E.
The GCC man page says -mcpu=powerpc64 "[specifies] a pure ... 64-bit big
endian PowerPC ... architecture machine [type], with an appropriate,
generic processor model assumed for scheduling purposes."
It's unclear how that interacts with -m32, which we are also passing,
although obviously -m32 is taking precedence in some sense, as the
32-bit kernel only contains 32-bit instructions.
This was noticed by inspection, not via any bug reports, but it does
affect code generation. Comparing before/after code generation, there
are some changes to instruction scheduling, and the after case (with
-mcpu=powerpc64 removed) the compiler seems more keen to use r8.
Fix it by making the else case only apply to Book3E 64, which excludes
32-bit.
Fixes: 0e00a8c9fd ("powerpc: Allow CPU selection also on PPC32")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220215112858.304779-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 749ed4a206 ]
Executing node_set_online() when nid = NUMA_NO_NODE results in an
undefined behavior. node_set_online() will call node_set_state(), into
__node_set(), into set_bit(), and since NUMA_NO_NODE is -1 we'll end up
doing a negative shift operation inside
arch/powerpc/include/asm/bitops.h. This potential UB was detected
running a kernel with CONFIG_UBSAN.
The behavior was introduced by commit 10f78fd0da ("powerpc/numa: Fix a
regression on memoryless node 0"), where the check for nid > 0 was
removed to fix a problem that was happening with nid = 0, but the result
is that now we're trying to online NUMA_NO_NODE nids as well.
Checking for nid >= 0 will allow node 0 to be onlined while avoiding
this UB with NUMA_NO_NODE.
Fixes: 10f78fd0da ("powerpc/numa: Fix a regression on memoryless node 0")
Reported-by: Ping Fang <pifang@redhat.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220224182312.1012527-1-danielhb413@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4226961b00 ]
Currently if a declaration appears in the BTF before the definition, the
definition is dumped as a conflicting name, e.g.:
$ bpftool btf dump file vmlinux format raw | grep "'unix_sock'"
[81287] FWD 'unix_sock' fwd_kind=struct
[89336] STRUCT 'unix_sock' size=1024 vlen=14
$ bpftool btf dump file vmlinux format c | grep "struct unix_sock"
struct unix_sock;
struct unix_sock___2 { <--- conflict, the "___2" is unexpected
struct unix_sock___2 *unix_sk;
This causes a compilation error if the dump output is used as a header file.
Fix it by skipping declaration when counting duplicated type names.
Fixes: 351131b51c ("libbpf: add btf_dump API for BTF-to-C conversion")
Signed-off-by: Xu Kuohai <xukuohai@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20220301053250.1464204-2-xukuohai@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dda7596c10 ]
insn_to_jit_off passed to bpf_prog_fill_jited_linfo() is calculated in
instruction granularity instead of bytes granularity, but BPF line info
requires byte offset.
bpf_prog_fill_jited_linfo() will be the last user of ctx.offset before
it is freed, so convert the offset into byte-offset before calling into
bpf_prog_fill_jited_linfo() in order to fix the line info dump on arm64.
Fixes: 37ab566c17 ("bpf: arm64: Enable arm64 jit to provide bpf_line_info")
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20220226121906.5709-3-houtao1@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7731754fd ]
The datasheet says that the BQ24190_REG_POC_CHG_CONFIG bits can
have a value of either 10(0x2) or 11(0x3) for OTG (5V boost regulator)
mode.
Sofar bq24190_vbus_is_enabled() was only checking for 10 but some BIOS-es
uses 11 when enabling the regulator at boot.
Make bq24190_vbus_is_enabled() also check for 11 so that it does not
wrongly returns false when the bits are set to 11.
Fixes: 66b6bef2c4 ("power: supply: bq24190_charger: Export 5V boost converter as regulator")
Cc: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 221e3638fe ]
The reference taken by 'of_find_device_by_node()' must be released when
not needed anymore. Add put_device() call to fix this.
Fixes: e94236cde4 ("drm/tegra: dsi: Add ganged mode support")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50b3a81899 ]
We need to calculate the max file size accurately if the total blocks
that can address by block tree exceed the upper_limit. But this check is
not correct now, it only compute the total data blocks but missing
metadata blocks are needed. So in the case of "data blocks < upper_limit
&& total blocks > upper_limit", we will get wrong result. Fortunately,
this case could not happen in reality, but it's confused and better to
correct the computing.
bits data blocks metadatablocks upper_limit
10 16843020 66051 2147483647
11 134480396 263171 1073741823
12 1074791436 1050627 536870911 (*)
13 8594130956 4198403 268435455 (*)
14 68736258060 16785411 134217727 (*)
15 549822930956 67125251 67108863 (*)
16 4398314962956 268468227 33554431 (*)
[*] Need to calculate in depth.
Fixes: 1c2d14212b ("ext2: Fix underflow in ext2_max_size()")
Link: https://lore.kernel.org/r/20220212050532.179055-1-yi.zhang@huawei.com
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39844b7e30 ]
__setup() handlers should return 1 if the parameter is handled.
Returning 0 causes the entire string to be added to init's
environment strings (limited to 32 strings), unnecessarily polluting it.
Using the documented strings "TOMOYO_loader=string1" and
"TOMOYO_trigger=string2" causes an Unknown parameter message:
Unknown kernel command line parameters
"BOOT_IMAGE=/boot/bzImage-517rc5 TOMOYO_loader=string1 \
TOMOYO_trigger=string2", will be passed to user space.
and these strings are added to init's environment string space:
Run /sbin/init as init process
with arguments:
/sbin/init
with environment:
HOME=/
TERM=linux
BOOT_IMAGE=/boot/bzImage-517rc5
TOMOYO_loader=string1
TOMOYO_trigger=string2
With this change, these __setup handlers act as expected,
and init's environment is not polluted with these strings.
Fixes: 0e4ae0e0de ("TOMOYO: Make several options configurable.")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru>
Link: https://lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru
Cc: James Morris <jmorris@namei.org>
Cc: Kentaro Takeda <takedakn@nttdata.co.jp>
Cc: tomoyo-dev-en@lists.osdn.me
Cc: "Serge E. Hallyn" <serge@hallyn.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d6736c3e1 ]
NCQ NON DATA is an NCQ command with the DMA_NONE DMA direction and so a
register-device-to-host-FIS response is expected for it.
However, for an IO_SUCCESS case, mpi_sata_completion() expects a
set-device-bits-FIS for any ata task with an use_ncq field true, which
includes NCQ NON DATA commands.
Fix this to correctly treat NCQ NON DATA commands as non-data by also
testing for the DMA_NONE DMA direction.
Link: https://lore.kernel.org/r/20220220031810.738362-16-damien.lemoal@opensource.wdc.com
Fixes: dbf9bfe615 ("[SCSI] pm8001: add SAS/SATA HBA driver")
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa028141ab ]
In the pm8001_chip_sata_req() and pm80xx_chip_sata_req() functions, all
tasks with a DMA direction of DMA_NONE (no data transfer) are initialized
using the ATAP value 0x04. However, NCQ NON DATA commands, while being
DMA_NONE commands are NCQ commands and need to be initialized using the
value 0x07 for ATAP, similarly to other NCQ commands.
Make sure that NCQ NON DATA command tasks are initialized similarly to
other NCQ commands by also testing the task "use_ncq" field in addition to
the DMA direction. While at it, reorganize the code into a chain of if -
else if - else to avoid useless affectations and debug messages.
Link: https://lore.kernel.org/r/20220220031810.738362-15-damien.lemoal@opensource.wdc.com
Fixes: dbf9bfe615 ("[SCSI] pm8001: add SAS/SATA HBA driver")
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd6d0e3762 ]
Make sure that the __le32 fields of struct sata_cmd are manipulated after
applying the correct endian conversion. That is, use cpu_to_le32() for
assigning values and le32_to_cpu() for consulting a field value. In
particular, make sure that the calculations for the 4G boundary check are
done using CPU endianness and *not* little endian values. With these fixes,
many sparse warnings are removed.
While at it, fix some code identation and add blank lines after variable
declarations and in some other places to make this code more readable.
Link: https://lore.kernel.org/r/20220220031810.738362-12-damien.lemoal@opensource.wdc.com
Fixes: 0ecdf00ba6 ("[SCSI] pm80xx: 4G boundary fix.")
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 970404cc57 ]
Make sure that the __le32 fields of struct ssp_ini_io_start_req are
manipulated after applying the correct endian conversion. That is, use
cpu_to_le32() for assigning values and le32_to_cpu() for consulting a field
value. In particular, make sure that the calculations for the 4G boundary
check are done using CPU endianness and *not* little endian values. With
these fixes, many sparse warnings are removed.
While at it, add blank lines after variable declarations and in some other
places to make this code more readable.
Link: https://lore.kernel.org/r/20220220031810.738362-11-damien.lemoal@opensource.wdc.com
Fixes: 0ecdf00ba6 ("[SCSI] pm80xx: 4G boundary fix.")
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca374f5d92 ]
All fields of the SASProtocolTimerConfig structure have the __le32 type.
As such, use cpu_to_le32() to initialize them. This change suppresses many
sparse warnings:
warning: incorrect type in assignment (different base types)
expected restricted __le32 [addressable] [usertype] pageCode
got int
Note that the check to limit the value of the STP_IDLE_TMO field is removed
as this field is initialized using the fixed (and small) value defined by
the STP_IDLE_TIME macro.
The pm8001_dbg() calls printing the values of the SASProtocolTimerConfig
structure fileds are changed to use le32_to_cpu() to present the values in
human readable form.
Link: https://lore.kernel.org/r/20220220031810.738362-9-damien.lemoal@opensource.wdc.com
Fixes: a6cb3d012b ("[SCSI] pm80xx: thermal, sas controller config and error handling update")
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6fc5150438 ]
Explicitly convert unsigned int in the right of the conditional
expression to int to match the left side operand and the return type,
fixing the following compiler warning:
drivers/md/dm-crypt.c:2593:43: warning: signed and unsigned
type in conditional expression [-Wsign-compare]
Fixes: c538f6ec9f ("dm crypt: add ability to use keys from the kernel key retention service")
Signed-off-by: Aashish Sharma <shraash@google.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e602f5156 ]
DP CTS test case 4.2.2.6 has valid edid with bad checksum on purpose
and expect DP source return correct checksum. During drm edid read,
correct edid checksum is calculated and stored at
connector::real_edid_checksum.
The problem is struct dp_panel::connector never be assigned, instead the
connector is stored in struct msm_dp::connector. When we run compliance
testing test case 4.2.2.6 dp_panel_handle_sink_request() won't have a valid
edid set in struct dp_panel::edid so we'll try to use the connectors
real_edid_checksum and hit a NULL pointer dereference error because the
connector pointer is never assigned.
Changes in V2:
-- populate panel connector at msm_dp_modeset_init() instead of at dp_panel_read_sink_caps()
Changes in V3:
-- remove unhelpful kernel crash trace commit text
-- remove renaming dp_display parameter to dp
Changes in V4:
-- add more details to commit text
Changes in v10:
-- group into one series
Changes in v11:
-- drop drm/msm/dp: dp_link_parse_sink_count() return immediately if aux read
Fixes: 7948fe12d4 ("drm/msm/dp: return correct edid checksum after corrupted edid checksum read")
Signee-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1642531648-8448-3-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 128f8ed590 ]
[Why]
When display topology changed on DSC hub we add all crtcs with dsc support to
atomic state.
Refer to patch:"drm/amd/display: Trigger modesets on MST DSC connectors"
However the original implementation may skip crtc if the topology change
caused by unplug.
That potentially could lead to no-lightup or corruption on DSC hub after
unplug event on one of the connectors.
[How]
Update add_affected_mst_dsc_crtcs() to use old connector state
if new connector state has no crtc (undergoes modeset due to unplug)
Fixes: 44be939ff7 ("drm/amd/display: Trigger modesets on MST DSC connectors")
Reviewed-by: Hersen Wu <hersenwu@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e610941c45 ]
[why]
pm sysfs should be writable in one VF mode as is in passthrough
[how]
do not remove write access on pm sysfs if device is in one VF mode
Fixes: 11c9cc95f8 ("amdgpu/pm: Make sysfs pm attributes as read-only for VFs")
Signed-off-by: Yiqing Yao <yiqing.yao@amd.com>
Reviewed-by: Monk Liu <Monk.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5e5e03e94 ]
Internally kernel prepends all report buffers, for both numbered and
unnumbered reports, with report ID, therefore to properly handle unnumbered
reports we should prepend it ourselves.
For the same reason we should skip the first byte of the buffer when
calling i2c_hid_set_or_send_report() which then will take care of properly
formatting the transfer buffer based on its separate report ID argument
along with report payload.
[jkosina@suse.cz: finalize trimmed sentence in changelog as spotted by Benjamin]
Fixes: 9b5a9ae885 ("HID: i2c-hid: implement ll_driver transport-layer callbacks")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a4760463d ]
kobject_init_and_add() takes reference even when it fails.
According to the doc of kobject_init_and_add()：
If this function returns an error, kobject_put() must be called to
properly clean up the memory associated with the object.
Fix memory leak by calling kobject_put().
Fixes: 8c0984e5a7 ("power: move power supply drivers to power/supply")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1528038385 ]
When the dw-hdmi bridge is in first place of the bridge chain, this
means there is no way to select an input format of the dw-hdmi HW
component.
Since introduction of display-connector, negotiation was broken since
the dw-hdmi negotiation code only worked when the dw-hdmi bridge was
in last position of the bridge chain or behind another bridge also
supporting input & output format negotiation.
Commit 7cd70656d1 ("drm/bridge: display-connector: implement bus fmts callbacks")
was introduced to make negotiation work again by making display-connector
act as a pass-through concerning input & output format negotiation.
But in the case where the dw-hdmi is single in the bridge chain, for
example on Renesas SoCs, with the display-connector bridge the dw-hdmi
is no more single, breaking output format.
Reported-by: Biju Das <biju.das.jz@bp.renesas.com>
Bisected-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Tested-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Fixes: 6c3c719936 ("drm/bridge: synopsys: dw-hdmi: add bus format negociation")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: add proper fixes commit]
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220204143337.89221-1-narmstrong@baylibre.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 735f5ae49e ]
The emulated bridge returns incorrect value for PCI_EXP_RTSTA register
during readout in advk_pci_bridge_emul_pcie_conf_read() function: the
correct bit is BIT(16), but we are setting BIT(23), because the code
does
*value = (isr0 & PCIE_MSG_PM_PME_MASK) << 16
where
PCIE_MSG_PM_PME_MASK
is
BIT(7).
The code should probably have been something like
*value = (!!(isr0 & PCIE_MSG_PM_PME_MASK)) << 16,
but we are better of using an if() and using the proper macro for this
bit.
Link: https://lore.kernel.org/r/20220110015018.26359-15-kabel@kernel.org
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 585d42bb57 ]
This chip has support for the same per-port policy actions found in
later versions of LinkStreet devices.
Fixes: f3a2cd326e ("net: dsa: mv88e6xxx: introduce .port_set_policy")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc8e2c707c ]
Check sta_rates pointer value in mt7603_sta_rate_tbl_update routine
since minstrel_ht_update_rates can fail allocating rates array.
Fixes: c8846e1015 ("mt76: add driver for MT7603E and MT7628/7688")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit abdb8bc94b ]
Similar to mt7915_mcu_wtbl_generic_tlv, rely on vif->bss_conf.aid for
aid in sta mode and not on sta->aid.
Fixes: e57b790146 ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a56b1b0f14 ]
mac80211 provides aid in vif->bss_conf.aid for sta mode and not in
sta->aid. Fix mt7915_mcu_wtbl_generic_tlv routine using proper value for
aid in sta mode.
Fixes: e57b790146 ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0198322379 ]
Trace IMC (In-Memory collection counters) in powerpc is useful for
application level profiling.
For trace_imc, presently task context (task_ctx_nr) is set to
perf_hw_context. But perf_hw_context should only be used for CPU PMU.
See commit 2665784850 ("perf/core: Verify we have a single
perf_hw_context PMU").
So for trace_imc, even though it is per thread PMU, it is preferred to
use sw_context in order to be able to do application level monitoring.
Hence change the task_ctx_nr to use perf_sw_context.
Fixes: 012ae24484 ("powerpc/perf: Trace imc PMU functions")
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Reviewed-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
[mpe: Update subject & incorporate notes into change log, reflow comment]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220202041837.65968-1-atrajeev@linux.vnet.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ebb747492 ]
On board rev A, the network interface labels for the switch ports
written on the front panel are different than on rev B and later.
This patch fixes network interface names for the switch ports according
to labels that are written on the front panel of the board rev B.
They start from ETH3 and end at ETH10.
This patch also introduces a separate device tree for rev A.
The main device tree is supposed to cover rev B and later.
Fixes: e69eb0824d ("powerpc: dts: t1040rdb: add ports for Seville Ethernet switch")
Signed-off-by: Maxim Kiselev <bigunclemax@gmail.com>
Reviewed-by: Maxim Kochetkov <fido_max@inbox.ru>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220121091447.3412907-1-bigunclemax@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba18dad0fb ]
platform_get_irq() returns negative error number instead 0 on failure.
And the doc of platform_get_irq() provides a usage example:
int irq = platform_get_irq(pdev, 0);
if (irq < 0)
return irq;
Fix the check of return value to catch errors correctly.
Fixes: f7a388d6cd ("power: reset: Add a driver for the Gemini poweroff")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6dba29537c ]
For now, if the XDP prog returns XDP_PASS on XSK, the metadata will
be lost as it doesn't get copied to the skb.
Copy it along with the frame headers. Account its size on skb
allocation, and when copying just treat it as a part of the frame
and do a pull after to "move" it to the "reserved" zone.
net_prefetch() xdp->data_meta and align the copy size to speed-up
memcpy() a little and better match i40e_construct_skb().
Fixes: 0a714186d3 ("i40e: add AF_XDP zero-copy Rx support")
Suggested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc97f9c6f9 ]
{__,}napi_alloc_skb() allocates and reserves additional NET_SKB_PAD
+ NET_IP_ALIGN for any skb.
OTOH, i40e_construct_skb_zc() currently allocates and reserves
additional `xdp->data - xdp->data_hard_start`, which is
XDP_PACKET_HEADROOM for XSK frames.
There's no need for that at all as the frame is post-XDP and will
go only to the networking stack core.
Pass the size of the actual data only to __napi_alloc_skb() and
don't reserve anything. This will give enough headroom for stack
processing.
Fixes: 0a714186d3 ("i40e: add AF_XDP zero-copy Rx support")
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1e0df1c57 ]
Syzbot reported 2 KMSAN bugs in ath9k. All of them are caused by missing
field initialization.
In htc_connect_service() svc_meta_len and pad are not initialized. Based
on code it looks like in current skb there is no service data, so simply
initialize svc_meta_len to 0.
htc_issue_send() does not initialize htc_frame_hdr::control array. Based
on firmware code, it will initialize it by itself, so simply zero whole
array to make KMSAN happy
Fail logs:
BUG: KMSAN: kernel-usb-infoleak in usb_submit_urb+0x6c1/0x2aa0 drivers/usb/core/urb.c:430
usb_submit_urb+0x6c1/0x2aa0 drivers/usb/core/urb.c:430
hif_usb_send_regout drivers/net/wireless/ath/ath9k/hif_usb.c:127 [inline]
hif_usb_send+0x5f0/0x16f0 drivers/net/wireless/ath/ath9k/hif_usb.c:479
htc_issue_send drivers/net/wireless/ath/ath9k/htc_hst.c:34 [inline]
htc_connect_service+0x143e/0x1960 drivers/net/wireless/ath/ath9k/htc_hst.c:275
...
Uninit was created at:
slab_post_alloc_hook mm/slab.h:524 [inline]
slab_alloc_node mm/slub.c:3251 [inline]
__kmalloc_node_track_caller+0xe0c/0x1510 mm/slub.c:4974
kmalloc_reserve net/core/skbuff.c:354 [inline]
__alloc_skb+0x545/0xf90 net/core/skbuff.c:426
alloc_skb include/linux/skbuff.h:1126 [inline]
htc_connect_service+0x1029/0x1960 drivers/net/wireless/ath/ath9k/htc_hst.c:258
...
Bytes 4-7 of 18 are uninitialized
Memory access of size 18 starts at ffff888027377e00
BUG: KMSAN: kernel-usb-infoleak in usb_submit_urb+0x6c1/0x2aa0 drivers/usb/core/urb.c:430
usb_submit_urb+0x6c1/0x2aa0 drivers/usb/core/urb.c:430
hif_usb_send_regout drivers/net/wireless/ath/ath9k/hif_usb.c:127 [inline]
hif_usb_send+0x5f0/0x16f0 drivers/net/wireless/ath/ath9k/hif_usb.c:479
htc_issue_send drivers/net/wireless/ath/ath9k/htc_hst.c:34 [inline]
htc_connect_service+0x143e/0x1960 drivers/net/wireless/ath/ath9k/htc_hst.c:275
...
Uninit was created at:
slab_post_alloc_hook mm/slab.h:524 [inline]
slab_alloc_node mm/slub.c:3251 [inline]
__kmalloc_node_track_caller+0xe0c/0x1510 mm/slub.c:4974
kmalloc_reserve net/core/skbuff.c:354 [inline]
__alloc_skb+0x545/0xf90 net/core/skbuff.c:426
alloc_skb include/linux/skbuff.h:1126 [inline]
htc_connect_service+0x1029/0x1960 drivers/net/wireless/ath/ath9k/htc_hst.c:258
...
Bytes 16-17 of 18 are uninitialized
Memory access of size 18 starts at ffff888027377e00
Fixes: fb9987d0f7 ("ath9k_htc: Support for AR9271 chipset.")
Reported-by: syzbot+f83a1df1ed4f67e8d8ad@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220115122733.11160-1-paskripkin@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 430e6a0212 ]
clang static analysis reports this represenative problem
amdgpu_smu.c:144:18: warning: The left operand of '*' is a garbage value
return clk_freq * 100;
~~~~~~~~ ^
If there is no get_dpm_ultimate_freq function,
smu_get_dpm_freq_range returns success without setting the
output min,max parameters. So return an -ENOTSUPP error.
Fixes: e5ef784b1e ("drm/amd/powerplay: revise calling chain on retrieving frequency range")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 588a70177d ]
In amdgpu_dm_connector_add_common_modes(), amdgpu_dm_create_common_mode()
is assigned to mode and is passed to drm_mode_probed_add() directly after
that. drm_mode_probed_add() passes &mode->head to list_add_tail(), and
there is a dereference of it in list_add_tail() without recoveries, which
could lead to NULL pointer dereference on failure of
amdgpu_dm_create_common_mode().
Fix this by adding a NULL check of mode.
This bug was found by a static analyzer.
Builds with 'make allyesconfig' show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: e7b07ceef2 ("drm/amd/display: Merge amdgpu_dm_types and amdgpu_dm")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2343bcdb47 ]
In nvkm_acr_hsfw_load_bl(), the return value of kmalloc() is directly
passed to memcpy(), which could lead to undefined behavior on failure
of kmalloc().
Fix this bug by using kmemdup() instead of kmalloc()+memcpy().
This bug was found by a static analyzer.
Builds with 'make allyesconfig' show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: 22dcda45a3 ("drm/nouveau/acr: implement new subdev to replace "secure boot"")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220124165856.57022-1-zhou1615@umn.edu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc0bf9de6f ]
Sparse seems to have gotten a little more picky lately and
we need to revisit this bit of code to make sparse happy.
warning: incorrect type in initializer (different address spaces)
expected union ionic_dev_cmd_regs *regs
got union ionic_dev_cmd_regs [noderef] __iomem *dev_cmd_regs
warning: incorrect type in argument 2 (different address spaces)
expected void [noderef] __iomem *
got unsigned int *
warning: incorrect type in argument 1 (different address spaces)
expected void volatile [noderef] __iomem *
got union ionic_dev_cmd *
Fixes: d701ec326a ("ionic: clean up sparse complaints")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75478b3b39 ]
The current code, when parsing the EDID Deep Color depths, that the
YUV422 cannot be used, referring to the HDMI 1.3 Specification.
This specification, in its section 6.2.4, indeed states:
For each supported Deep Color mode, RGB 4:4:4 shall be supported and
optionally YCBCR 4:4:4 may be supported.
YCBCR 4:2:2 is not permitted for any Deep Color mode.
This indeed can be interpreted like the code does, but the HDMI 1.4
specification further clarifies that statement in its section 6.2.4:
For each supported Deep Color mode, RGB 4:4:4 shall be supported and
optionally YCBCR 4:4:4 may be supported.
YCBCR 4:2:2 is also 36-bit mode but does not require the further use
of the Deep Color modes described in section 6.5.2 and 6.5.3.
This means that, even though YUV422 can be used with 12 bit per color,
it shouldn't be treated as a deep color mode.
This is also broken with YUV444 if it's supported by the display, but
DRM_EDID_HDMI_DC_Y444 isn't set. In such a case, the code will clear
color_formats of the YUV444 support set previously in
drm_parse_cea_ext(), but will not set it back.
Since the formats supported are already setup properly in
drm_parse_cea_ext(), let's just remove the code modifying the formats in
drm_parse_hdmi_deep_color_info()
Fixes: d0c94692e0 ("drm/edid: Parse and handle HDMI deep color modes.")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220120151625.594595-3-maxime@cerno.tech
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e68f331c8 ]
For the possible failure of the platform_get_irq(), the returned irq
could be error number and will finally cause the failure of the
request_irq().
Consider that platform_get_irq() can now in certain cases return
-EPROBE_DEFER, and the consequences of letting request_irq() effectively
convert that into -EINVAL, even at probe time rather than later on.
So it might be better to check just now.
Fixes: 2c22120fbd ("MTD: OneNAND: interrupt based wait support")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220104162658.1988142-1-jiasheng@iscas.ac.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d7cbe2b9c ]
kvartet reported, that hci_uart_tx_wakeup() uses uninitialized rwsem.
The problem was in wrong place for percpu_init_rwsem() call.
hci_uart_proto::open() may register a timer whose callback may call
hci_uart_tx_wakeup(). There is a chance, that hci_uart_register_device()
thread won't be fast enough to call percpu_init_rwsem().
Fix it my moving percpu_init_rwsem() call before p->open().
INFO: trying to register non-static key.
The code is fine but needs lockdep annotation, or maybe
you didn't initialize this object before use?
turning off the locking correctness validator.
CPU: 2 PID: 18524 Comm: syz-executor.5 Not tainted 5.16.0-rc6 #9
...
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
assign_lock_key kernel/locking/lockdep.c:951 [inline]
register_lock_class+0x148d/0x1950 kernel/locking/lockdep.c:1263
__lock_acquire+0x106/0x57e0 kernel/locking/lockdep.c:4906
lock_acquire kernel/locking/lockdep.c:5637 [inline]
lock_acquire+0x1ab/0x520 kernel/locking/lockdep.c:5602
percpu_down_read_trylock include/linux/percpu-rwsem.h:92 [inline]
hci_uart_tx_wakeup+0x12e/0x490 drivers/bluetooth/hci_ldisc.c:124
h5_timed_event+0x32f/0x6a0 drivers/bluetooth/hci_h5.c:188
call_timer_fn+0x1a5/0x6b0 kernel/time/timer.c:1421
Fixes: d73e172816 ("Bluetooth: hci_serdev: Init hci_uart proto_lock to avoid oops")
Reported-by: Yiru Xu <xyru1999@gmail.com>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a32ea51a3f ]
When I checked the code in skeleton header file generated with my own
bpf prog, I found there may be possible NULL pointer dereference when
destroying skeleton. Then I checked the in-tree bpf progs, finding that is
a common issue. Let's take the generated samples/bpf/xdp_redirect_cpu.skel.h
for example. Below is the generated code in
xdp_redirect_cpu__create_skeleton():
xdp_redirect_cpu__create_skeleton
struct bpf_object_skeleton *s;
s = (struct bpf_object_skeleton *)calloc(1, sizeof(*s));
if (!s)
goto error;
...
error:
bpf_object__destroy_skeleton(s);
return -ENOMEM;
After goto error, the NULL 's' will be deferenced in
bpf_object__destroy_skeleton().
We can simply fix this issue by just adding a NULL check in
bpf_object__destroy_skeleton().
Fixes: d66562fba1 ("libbpf: Add BPF object skeleton support")
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20220108134739.32541-1-laoar.shao@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3fb3d4418 ]
In function ath10k_wow_convert_8023_to_80211(), it will do memcpy for
the new->pattern, and currently the new->pattern and new->mask is same
with the old, then the memcpy of new->pattern will also overwrite the
old->pattern, because the header format of new->pattern is 802.11,
its length is larger than the old->pattern which is 802.3. Then the
operation of "Copy frame body" will copy a mistake value because the
body memory has been overwrite when memcpy the new->pattern.
Assign another empty value to new_pattern to avoid the overwrite issue.
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00049
Fixes: fa3440fa2f ("ath10k: convert wow pattern from 802.3 to 802.11")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211222031347.25463-1-quic_wgong@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5eb04d7a0 ]
Commit 06b93644f4 ("media: Kconfig: add an option to filter in/out
platform drivers") introduced CONFIG_MEDIA_PLATFORM_SUPPORT, to allow
more fine grained control over the inclusion of certain Kconfig files.
multi_v5_defconfig was selecting some drivers described in
drivers/media/platform/Kconfig, which now wasn't included anymore.
Explicitly set the new symbol in multi_v5_defconfig to bring those
drivers back.
This enables some new V4L2 and VIDEOBUF2 features, but as modules only.
Fixes: 06b93644f4 ("media: Kconfig: add an option to filter in/out platform drivers")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20220317183043.948432-3-andre.przywara@arm.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ae0a4d8fe ]
This function only calls of_node_put() in the regular path.
And it will cause refcount leak in error paths.
For example, when codec_np is NULL, saif_np[0] and saif_np[1]
are not NULL, it will cause leaks.
of_node_put() will check if the node pointer is NULL, so we can
call it directly to release the refcount of regular pointers.
Fixes: e968194b45 ("ASoC: mxs: add device tree support for mxs-sgtl5000")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220308020146.26496-1-linmq006@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 25e9413921 ]
The VIDIOC_G_FBUF and related overlay ioctls no longer worked (-ENOTTY was
returned).
The root cause was the introduction of the caps field in ivtv-driver.h.
While loading the ivtvfb module would update the video_device device_caps
field with V4L2_CAP_VIDEO_OUTPUT_OVERLAY it would not update that caps
field, and that's what the overlay ioctls would look at.
It's a bad idea to keep information in two places, so drop the caps field
and only use vdev.device_caps.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Martin Dauskardt <martin.dauskardt@gmx.de>
Fixes: 2161536516 (media: media/pci: set device_caps in struct video_device)
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f1f4b6424 ]
'dev' will *always* be set by list_for_each_entry().
It is incorrect to assume that the iterator value will be NULL if the
list is empty.
Instead of checking the pointer it should be checked if
the list is empty.
Fixes: 79dd0c69f0 ("V4L: 925: saa7134 alsa is now a standalone module")
Signed-off-by: Jakob Koschel <jakobkoschel@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a58c22cfbb ]
The device_node pointer is returned by of_parse_phandle() with refcount
incremented. We should use of_node_put() on it when done.
Fixes: f76ee892a9 ("omapfb: copy omapdss & displays for omapfb")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6a21a1410 ]
As the possible failure of the vzalloc(), e->encoder_buf might be NULL.
Therefore, it should be better to check it in order
to guarantee the success of the initialization.
If fails, we need to free not only 'e' but also 'e->name'.
Also, if the allocation for ctx fails, we need to free 'e->encoder_buf'
else.
Fixes: f90cf6079b ("media: vidtv: add a bridge driver")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6e1e7b19f ]
When CONFIG_MCF_EDMA is set (due to COMPILE_TEST, not due to
CONFIG_M5441x), coldfire/device.c has compile errors due to
missing MCFEDMA_* symbols. In the .config file that was provided,
CONFIG_M5206=y, not CONFIG_M5441x, so <asm/m5441xsim.h> is not
included in coldfire/device.c.
Only build the MCF_EDMA code in coldfire/device.c if the MCFEDMA_*
hardware macros are defined.
Fixes these build errors:
../arch/m68k/coldfire/device.c:512:35: error: 'MCFEDMA_BASE' undeclared here (not in a function); did you mean 'MCFDMA_BASE1'?
512 | .start = MCFEDMA_BASE,
../arch/m68k/coldfire/device.c:513:50: error: 'MCFEDMA_SIZE' undeclared here (not in a function)
513 | .end = MCFEDMA_BASE + MCFEDMA_SIZE - 1,
../arch/m68k/coldfire/device.c:517:35: error: 'MCFEDMA_IRQ_INTR0' undeclared here (not in a function)
517 | .start = MCFEDMA_IRQ_INTR0,
../arch/m68k/coldfire/device.c:523:35: error: 'MCFEDMA_IRQ_INTR16' undeclared here (not in a function)
523 | .start = MCFEDMA_IRQ_INTR16,
../arch/m68k/coldfire/device.c:529:35: error: 'MCFEDMA_IRQ_INTR56' undeclared here (not in a function)
529 | .start = MCFEDMA_IRQ_INTR56,
../arch/m68k/coldfire/device.c:535:35: error: 'MCFEDMA_IRQ_ERR' undeclared here (not in a function)
535 | .start = MCFEDMA_IRQ_ERR,
Fixes: d7e9d01ac2 ("m68k: add ColdFire mcf5441x eDMA platform support")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Link: lore.kernel.org/r/202203030252.P752DK46-lkp@intel.com
Cc: Angelo Dureghello <angelo@sysam.it>
Cc: Greg Ungerer <gerg@kernel.org>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-m68k@lists.linux-m68k.org
Cc: uclinux-dev@uclinux.org
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf0cd60b7e ]
AV/C deferred transaction was supported at a commit 00a7bb81c2 ("ALSA:
firewire-lib: Add support for deferred transaction") while 'deferrable'
flag can be uninitialized for non-control/notify AV/C transactions.
UBSAN reports it:
kernel: ================================================================================
kernel: UBSAN: invalid-load in /build/linux-aa0B4d/linux-5.15.0/sound/firewire/fcp.c:363:9
kernel: load of value 158 is not a valid value for type '_Bool'
kernel: CPU: 3 PID: 182227 Comm: irq/35-firewire Tainted: P OE 5.15.0-18-generic #18-Ubuntu
kernel: Hardware name: Gigabyte Technology Co., Ltd. AX370-Gaming 5/AX370-Gaming 5, BIOS F42b 08/01/2019
kernel: Call Trace:
kernel: <IRQ>
kernel: show_stack+0x52/0x58
kernel: dump_stack_lvl+0x4a/0x5f
kernel: dump_stack+0x10/0x12
kernel: ubsan_epilogue+0x9/0x45
kernel: __ubsan_handle_load_invalid_value.cold+0x44/0x49
kernel: fcp_response.part.0.cold+0x1a/0x2b [snd_firewire_lib]
kernel: fcp_response+0x28/0x30 [snd_firewire_lib]
kernel: fw_core_handle_request+0x230/0x3d0 [firewire_core]
kernel: handle_ar_packet+0x1d9/0x200 [firewire_ohci]
kernel: ? handle_ar_packet+0x1d9/0x200 [firewire_ohci]
kernel: ? transmit_complete_callback+0x9f/0x120 [firewire_core]
kernel: ar_context_tasklet+0xa8/0x2e0 [firewire_ohci]
kernel: tasklet_action_common.constprop.0+0xea/0xf0
kernel: tasklet_action+0x22/0x30
kernel: __do_softirq+0xd9/0x2e3
kernel: ? irq_finalize_oneshot.part.0+0xf0/0xf0
kernel: do_softirq+0x75/0xa0
kernel: </IRQ>
kernel: <TASK>
kernel: __local_bh_enable_ip+0x50/0x60
kernel: irq_forced_thread_fn+0x7e/0x90
kernel: irq_thread+0xba/0x190
kernel: ? irq_thread_fn+0x60/0x60
kernel: kthread+0x11e/0x140
kernel: ? irq_thread_check_affinity+0xf0/0xf0
kernel: ? set_kthread_struct+0x50/0x50
kernel: ret_from_fork+0x22/0x30
kernel: </TASK>
kernel: ================================================================================
This commit fixes the bug. The bug has no disadvantage for the non-
control/notify AV/C transactions since the flag has an effect for AV/C
response with INTERIM (0x0f) status which is not used for the transactions
in AV/C general specification.
Fixes: 00a7bb81c2 ("ALSA: firewire-lib: Add support for deferred transaction")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20220304125647.78430-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de2c6f9881 ]
There is one call trace that snd_soc_register_card()
->snd_soc_bind_card()->soc_init_pcm_runtime()
->snd_soc_dai_compress_new()->snd_soc_new_compress().
In the trace the 'codec_dai' transfers from card->dai_link,
and we can see from the snd_soc_add_pcm_runtime() in
snd_soc_bind_card() that, if value of card->dai_link->num_codecs
is 0, then 'codec_dai' could be null pointer caused
by index out of bound in 'asoc_rtd_to_codec(rtd, 0)'.
And snd_soc_register_card() is called by various platforms.
Therefore, it is better to add the check in the case of misusing.
And because 'cpu_dai' has already checked in soc_init_pcm_runtime(),
there is no need to check again.
Adding the check as follow, then if 'codec_dai' is null,
snd_soc_new_compress() will not pass through the check
'if (playback + capture != 1)', avoiding the leftover use of
'codec_dai'.
Fixes: 467fece ("ASoC: soc-dai: move snd_soc_dai_stream_valid() to soc-dai.c")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/1634285633-529368-1-git-send-email-jiasheng@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55927cb44d ]
After converting ahci-platform txt binding to yaml nodename is reported
as not matching the standard:
arch/arm64/boot/dts/broadcom/northstar2/ns2-svk.dt.yaml:
ahci@663f2000: $nodename:0: 'ahci@663f2000' does not match '^sata(@.*)?$'
Fix it to match binding.
Fixes: ac9aae00f0 ("arm64: dts: Add SATA3 AHCI and SATA3 PHY DT nodes for NS2")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c953c764e5 ]
Broadcom ns2 platform has spi-cpol and spi-cpho properties set
incorrectly. As per spi-slave-peripheral-prop.yaml, these properties are
of flag or boolean type and not integer type. Fix the values.
Fixes: d69dbd9f41 (arm64: dts: Add ARM PL022 SPI DT nodes for NS2)
Signed-off-by: Kuldeep Singh <singh.kuldeep87k@gmail.com>
CC: Ray Jui <rjui@broadcom.com>
CC: Scott Branden <sbranden@broadcom.com>
CC: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a97b693c37 ]
These two architectures implement 8-byte get_user() through
a memcpy() into a four-byte variable, which won't fit.
Use a temporary 64-bit variable instead here, and use a double
cast the way that risc-v and openrisc do to avoid compile-time
warnings.
Fixes: 6a090e9797 ("arch/microblaze: support get_user() of size 8 bytes")
Fixes: 5ccc6af5e8 ("nios2: Memory management")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fecd363ae2 ]
According to BSP library source, H264 neighbour info buffer size needs
to be 32 kiB for H6. This is similar to H265 decoding, which also needs
double buffer size in comparison to older Cedrus core generations.
Increase buffer size to cover H6 needs. Since increase is not that big
in absolute numbers, it doesn't make sense to complicate logic for older
generations.
Issue was discovered using iommu and cross checked with BSP library
source.
Fixes: 6eb9b758e3 ("media: cedrus: Add H264 decoding support")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee8b887329 ]
Neighbour info buffer size needs to be 794 kiB in H6. This is actually
already indirectly mentioned in the comment, but smaller size is used
nevertheless.
Increase buffer size to cover H6 needs. Since increase is not that big
in absolute numbers, it doesn't make sense to complicate logic for older
generations.
Bug was discovered using iommu, which reported access error when trying
to play H265 video.
Fixes: 86caab29da ("media: cedrus: Add HEVC/H.265 decoding support")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c08eadca1b ]
The commit 47677e51e2a4("[media] em28xx: Only deallocate struct
em28xx after finishing all extensions") adds kref_get to many init
functions (e.g., em28xx_audio_init). However, kref_init is called too
late in em28xx_usb_probe, since em28xx_init_dev before will invoke
those init functions and call kref_get function. Then refcount bug
occurs in my local syzkaller instance.
Fix it by moving kref_init before em28xx_init_dev. This issue occurs
not only in dev but also dev->dev_next.
Fixes: 47677e51e2 ("[media] em28xx: Only deallocate struct em28xx after finishing all extensions")
Reported-by: syzkaller <syzkaller@googlegroups.com>
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a92fc6e55 ]
Calling hdmi_infoframe_unpack() with static sizeof(buffer) skips all
the size checking done later in hdmi_infoframe_unpack(). A better
value is the amount of data read into buffer.
Fixes: 480b8b3e42 ("video/hdmi: Pass buffer size to infoframe unpack functions")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3d66a164c ]
platform_get_irq() returns negative error number instead 0 on failure.
And the doc of platform_get_irq() provides a usage example:
int irq = platform_get_irq(pdev, 0);
if (irq < 0)
return irq;
Fix the check of return value to catch errors correctly.
Fixes: cdd5de500b ("soc: ti: Add wkup_m3_ipc driver")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Dave Gerlach <d-gerlach@ti.com>
Link: https://lore.kernel.org/r/20220114062840.16620-1-linmq006@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 625c24460d ]
replace millivolt with correct microvolt and adjust value to
the minimal value allowed by documentation.
Found with `make qcom/sdm845-oneplus-fajita.dtb`.
Fixes:
arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dt.yaml: codec@1: 'qcom,micbias1-microvolt' is a required property
From schema: Documentation/devicetree/bindings/sound/qcom,wcd934x.yaml
arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dt.yaml: codec@1: 'qcom,micbias2-microvolt' is a required property
From schema: Documentation/devicetree/bindings/sound/qcom,wcd934x.yaml
arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dt.yaml: codec@1: 'qcom,micbias3-microvolt' is a required property
From schema: Documentation/devicetree/bindings/sound/qcom,wcd934x.yaml
arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dt.yaml: codec@1: 'qcom,micbias4-microvolt' is a required property
From schema: Documentation/devicetree/bindings/sound/qcom,wcd934x.yaml
arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dt.yaml: codec@1: 'qcom,micbias1-millivolt', 'qcom,micbias2-millivolt', 'qcom,micbias3-millivolt', 'qcom,micbias4-millivolt' do not match any of the regexes: '^.*@[0-9a-f]+$', 'pinctrl-[0-9]+'
Fixes: 27ca1de07d ("arm64: dts: qcom: sdm845: add slimbus nodes")
Signed-off-by: David Heidelberg <david@ixit.cz>
Tested-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211213195105.114596-1-david@ixit.cz
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8030cb9a55 ]
Quoting the header comments, IRQF_ONESHOT is "Used by threaded interrupts
which need to keep the irq line disabled until the threaded handler has
been run.". When applied to an interrupt that doesn't request a threaded
irq then IRQF_ONESHOT has a lesser known (undocumented?) side effect,
which it to disable the forced threading of the irq. For "normal" kernels
(without forced threading) then, if there is no thread_fn, then
IRQF_ONESHOT is a nop.
In this case disabling forced threading is not appropriate for this driver
because it calls wake_up_all() and this API cannot be called from
no-thread interrupt handlers on PREEMPT_RT systems (deadlock risk, triggers
sleeping-while-atomic warnings).
Fix this by removing IRQF_ONESHOT.
Fixes: 2209481409 ("soc: qcom: Add AOSS QMP driver")
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
[bjorn: Added Fixes tag]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220127173554.158111-1-daniel.thompson@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a811126d3 ]
Because of the possible failure of the allocation, data->domains might
be NULL pointer and will cause the dereference of the NULL pointer
later.
Therefore, it might be better to check it and directly return -ENOMEM
without releasing data manually if fails, because the comment of the
devm_kmalloc() says "Memory allocated with this function is
automatically freed on driver detach.".
Fixes: bbe3a66c3f ("soc: qcom: rpmpd: Add a Power domain driver to model corners")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211231094419.1941054-1-jiasheng@iscas.ac.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78482af095 ]
This code has two bugs:
1) "cnt" is 255 but the size of the buffer is 256 so the last byte is
not used.
2) If we try to print more than 255 characters then "cnt" will be
negative and that will trigger a WARN() in snprintf(). The fix for
this is to use scnprintf() instead of snprintf().
We can re-write this code to be cleaner:
1) Rename "offset" to "off" because that's shorter.
2) Get rid of the "cnt" variable and just use "size - off" directly.
3) Get rid of the "read" variable and just increment "off" directly.
Fixes: 96fe6a2109 ("fbdev: Add VESA Coordinated Video Timings (CVT) support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1791f487f8 ]
I got a null-ptr-deref report:
BUG: kernel NULL pointer dereference, address: 0000000000000000
...
RIP: 0010:fb_destroy_modelist+0x38/0x100
...
Call Trace:
ufx_usb_probe.cold+0x2b5/0xac1 [smscufx]
usb_probe_interface+0x1aa/0x3c0 [usbcore]
really_probe+0x167/0x460
...
ret_from_fork+0x1f/0x30
If fb_alloc_cmap() fails in ufx_usb_probe(), fb_destroy_modelist() will
be called to destroy modelist in the error handling path. But modelist
has not been initialized yet, so it will result in null-ptr-deref.
Initialize modelist before calling fb_alloc_cmap() to fix this bug.
Fixes: 3c8a63e22a ("Add support for SMSC UFX6000/7000 USB display adapters")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 567e44fb51 ]
If PPC_BOOK3S, PPC_PMAC and PPC32 is n, COMPILE_TEST build fails:
drivers/video/fbdev/controlfb.c:70:0: error: "pgprot_cached_wthru" redefined [-Werror]
#define pgprot_cached_wthru(prot) (prot)
In file included from ./arch/powerpc/include/asm/pgtable.h:20:0,
from ./include/linux/pgtable.h:6,
from ./include/linux/mm.h:33,
from drivers/video/fbdev/controlfb.c:37:
./arch/powerpc/include/asm/nohash/pgtable.h:243:0: note: this is the location of the previous definition
#define pgprot_cached_wthru(prot) (__pgprot((pgprot_val(prot) & ~_PAGE_CACHE_CTL) | \
Fixes: a07a63b0e2 ("video: fbdev: controlfb: add COMPILE_TEST support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62d89a7d49 ]
Start from commit 11be60bd66 "matroxfb: add Matrox MGA-G200eW board
support", when maxvram is 0x800000, monitor become black w/ error message
said: "The current input timing is not supported by the monitor display.
Please change your input timing to 1920x1080@60Hz ...".
Fixes: 11be60bd66 ("matroxfb: add Matrox MGA-G200eW board support")
Signed-off-by: Z. Liu <liuzx@knownsec.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b732a0016 ]
Previous reg-field, 0x98[11:0], stands for the period of the detected
hsync signal.
Use the correct reg, 0xa0, to get h-total in pixels.
Fixes: d2b4387f3b ("media: platform: Add Aspeed Video Engine driver")
Signed-off-by: Jammy Huang <jammy_huang@aspeedtech.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89d78e0133 ]
The Hantro H1 hardware can crop off pixels from the right and bottom of
the source frame. These are controlled with the H1_REG_IN_IMG_CTRL_OVRFLB
and H1_REG_IN_IMG_CTRL_OVRFLR in the H1_REG_IN_IMG_CTRL register.
The ChromeOS kernel driver that this was based on incorrectly added the
_D4 suffix H1_REG_IN_IMG_CTRL_OVRFLB. This field crops the bottom of the
input frame, and the number is _not_ divided by 4. [1]
Correct the name to avoid confusion when crop support with the selection
API is added.
[1] https://chromium.googlesource.com/chromiumos/third_party/kernel/+/refs/ \
heads/chromeos-4.19/drivers/staging/media/hantro/hantro_h1_vp8_enc.c#377
Fixes: 775fec6900 ("media: add Rockchip VPU JPEG encoder driver")
Fixes: a29add8c9b ("media: rockchip/vpu: rename from rockchip to hantro")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8c80c9961 ]
As the possible failure of the kzalloc(), the 'new_ts' could be NULL
pointer.
Therefore, it should be better to check it in order to avoid the
dereference of the NULL pointer.
Also, the caller esparser_queue() needs to deal with the return value of
the amvdec_add_ts().
Fixes: 876f123b89 ("media: meson: vdec: bring up to compliance")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Suggested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca85d27153 ]
The reference taken by 'of_find_device_by_node()' must be released when
not needed anymore.
Add the corresponding 'put_device()' in the error handling path.
Fixes: e7f3c54810 ("[media] coda: use VDOA for un-tiling custom macroblock format")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c5091fbe7 ]
This driver did not set the MM2S Fs Multiplier Register to the proper
value for playback streams. This needs to be set to the sample rate to
MCLK multiplier, or random stream underflows can occur on the downstream
I2S transmitter.
Store the sysclk value provided via the set_sysclk callback and use that
in conjunction with the sample rate in the hw_params callback to calculate
the proper value to set for this register.
Fixes: 6f6c3c36f0 ("ASoC: xlnx: add pcm formatter platform driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220120195832.1742271-2-robert.hancock@calian.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef058cc8b7 ]
Commit 2161536516 ("media: media/pci: set device_caps in struct video_device")
introduced a regression: V4L2_CAP_TUNER is always present in device_caps,
even when the device has no tuner.
This causes a warning:
WARNING: CPU: 0 PID: 249 at drivers/media/v4l2-core/v4l2-ioctl.c:1102 v4l_querycap+0xa0/0xb0 [videodev]
Fixes: 2161536516 ("media: media/pci: set device_caps in struct video_device")
Signed-off-by: Ondrej Zary <linux@zary.sk>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e25a89f743 ]
The return value of devm_kzalloc() needs to be checked.
To avoid use of null pointer in case of thefailure of alloc.
Fixes: 46233e91fa ("media: mtk-vcodec: move firmware implementations into their own files")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reviewed-by: Tzung-Bi Shih <tzungbi@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8310ca9407 ]
DST_QUEUE_OFF_BASE is applied to offset/mem_offset on MMAP capture buffers
only for the VIDIOC_QUERYBUF ioctl, while the userspace fields (including
offset/mem_offset) are filled in for VIDIOC_{QUERY,PREPARE,Q,DQ}BUF
ioctls. This leads to differences in the values presented to userspace.
If userspace attempts to mmap the capture buffer directly using values
from DQBUF, it will fail.
Move the code that applies the magic offset into a helper, and call
that helper from all four ioctl entry points.
[hverkuil: drop unnecessary '= 0' in v4l2_m2m_querybuf() for ret]
Fixes: 7f98639def ("V4L/DVB: add memory-to-memory device helper framework for videobuf")
Fixes: 908a0d7c58 ("[media] v4l: mem2mem: port to videobuf2")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 241f5b67fb ]
vb2_dma_contig_set_max_seg_size need to have a size in parameter and not
a DMA_BIT_MASK().
While fixing this issue, also fix error handling of all DMA size
setting.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: d4ae368922 ("media: zoran: device support only 32bit DMA address")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b56adcf52 ]
When compressed file has blocks, f2fs_ioc_start_atomic_write will succeed,
but compressed flag will be remained in inode. If write partial compreseed
cluster and commit atomic write will cause data corruption.
This is the reproduction process:
Step 1:
create a compressed file ,write 64K data , call fsync(), then the blocks
are write as compressed cluster.
Step2:
iotcl(F2FS_IOC_START_ATOMIC_WRITE) --- this should be fail, but not.
write page 0 and page 3.
iotcl(F2FS_IOC_COMMIT_ATOMIC_WRITE) -- page 0 and 3 write as normal file,
Step3:
drop cache.
read page 0-4 -- Since page 0 has a valid block address, read as
non-compressed cluster, page 1 and 2 will be filled with compressed data
or zero.
The root cause is, after commit 7eab7a6968 ("f2fs: compress: remove
unneeded read when rewrite whole cluster"), in step 2, f2fs_write_begin()
only set target page dirty, and in f2fs_commit_inmem_pages(), we will write
partial raw pages into compressed cluster, result in corrupting compressed
cluster layout.
Fixes: 4c8ff7095b ("f2fs: support data compression")
Fixes: 7eab7a6968 ("f2fs: compress: remove unneeded read when rewrite whole cluster")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Fengnan Chang <changfengnan@vivo.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7eab7a6968 ]
when we overwrite the whole page in cluster, we don't need read original
data before write, because after write_end(), writepages() can help to
load left data in that cluster.
Signed-off-by: Fengnan Chang <changfengnan@vivo.com>
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Acked-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f4613cdbe ]
When reflinking an inline extent, we assert that its file offset is 0 and
that its uncompressed length is not greater than the sector size. We then
return an error if one of those conditions is not satisfied. However we
use a return statement, which results in returning from btrfs_clone()
without freeing the path and buffer that were allocated before, as well as
not clearing the flag BTRFS_INODE_NO_DELALLOC_FLUSH for the destination
inode.
Fix that by jumping to the 'out' label instead, and also add a WARN_ON()
for each condition so that in case assertions are disabled, we get to
known which of the unexpected conditions triggered the error.
Fixes: a61e1e0df9 ("Btrfs: simplify inline extent handling when doing reflinks")
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 344150999b ]
Quoted from Jing Xia's report, there is a potential deadlock may happen
between kworker and checkpoint as below:
[T:writeback] [T:checkpoint]
- wb_writeback
- blk_start_plug
bio contains NodeA was plugged in writeback threads
- do_writepages -- sync write inodeB, inc wb_sync_req[DATA]
- f2fs_write_data_pages
- f2fs_write_single_data_page -- write last dirty page
- f2fs_do_write_data_page
- set_page_writeback -- clear page dirty flag and
PAGECACHE_TAG_DIRTY tag in radix tree
- f2fs_outplace_write_data
- f2fs_update_data_blkaddr
- f2fs_wait_on_page_writeback -- wait NodeA to writeback here
- inode_dec_dirty_pages
- writeback_sb_inodes
- writeback_single_inode
- do_writepages
- f2fs_write_data_pages -- skip writepages due to wb_sync_req[DATA]
- wbc->pages_skipped += get_dirty_pages() -- PAGECACHE_TAG_DIRTY is not set but get_dirty_pages() returns one
- requeue_inode -- requeue inode to wb->b_dirty queue due to non-zero.pages_skipped
- blk_finish_plug
Let's try to avoid deadlock condition by forcing unplugging previous bio via
blk_finish_plug(current->plug) once we'v skipped writeback in writepages()
due to valid sbi->wb_sync_req[DATA/NODE].
Fixes: 687de7f101 ("f2fs: avoid IO split due to mixed WB_SYNC_ALL and WB_SYNC_NONE")
Signed-off-by: Zhiguo Niu <zhiguo.niu@unisoc.com>
Signed-off-by: Jing Xia <jing.xia@unisoc.com>
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfdf4e6208 ]
The rseq rseq_cs.ptr.{ptr32,padding} uapi endianness handling is
entirely wrong on 32-bit little endian: a preprocessor logic mistake
wrongly uses the big endian field layout on 32-bit little endian
architectures.
Fortunately, those ptr32 accessors were never used within the kernel,
and only meant as a convenience for user-space.
Remove those and replace the whole rseq_cs union by a __u64 type, as
this is the only thing really needed to express the ABI. Document how
32-bit architectures are meant to interact with this field.
Fixes: ec9c82e03a ("rseq: uapi: Declare rseq_cs field as union, update includes")
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20220127152720.25898-1-mathieu.desnoyers@efficios.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28c988c3ec ]
The older format of /proc/pid/sched printed home node info which
required the mempolicy and task lock around mpol_get(). However
the format has changed since then and there is no need for
sched_show_numa() any more to have mempolicy argument,
asssociated mpol_get/put and task_lock/unlock. Remove them.
Fixes: 397f2378f1 ("sched/numa: Fix numa balancing stats in /proc/pid/sched")
Signed-off-by: Bharata B Rao <bharata@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Link: https://lore.kernel.org/r/20220118050515.2973-1-bharata@amd.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d19e3dab0 ]
It needs to assign sbi->gc_mode with GC_IDLE_AT rather than GC_AT when
user tries to enable ATGC via gc_idle sysfs interface, fix it.
Fixes: 093749e296 ("f2fs: support age threshold based garbage collection")
Cc: Zhipeng Tan <tanzhipeng@hust.edu.cn>
Signed-off-by: Jicheng Shao <shaojicheng@hust.edu.cn>
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a635415a06 ]
In watch_queue_set_size(), the error cleanup code doesn't take account of
the fact that __free_page() can't handle a NULL pointer when trying to free
up buffer pages that did get allocated.
Fix this by only calling __free_page() on the pages actually allocated.
Without the fix, this can lead to something like the following:
BUG: KASAN: null-ptr-deref in __free_pages+0x1f/0x1b0 mm/page_alloc.c:5473
Read of size 4 at addr 0000000000000034 by task syz-executor168/3599
...
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
__kasan_report mm/kasan/report.c:446 [inline]
kasan_report.cold+0x66/0xdf mm/kasan/report.c:459
check_region_inline mm/kasan/generic.c:183 [inline]
kasan_check_range+0x13d/0x180 mm/kasan/generic.c:189
instrument_atomic_read include/linux/instrumented.h:71 [inline]
atomic_read include/linux/atomic/atomic-instrumented.h:27 [inline]
page_ref_count include/linux/page_ref.h:67 [inline]
put_page_testzero include/linux/mm.h:717 [inline]
__free_pages+0x1f/0x1b0 mm/page_alloc.c:5473
watch_queue_set_size+0x499/0x630 kernel/watch_queue.c:275
pipe_ioctl+0xac/0x2b0 fs/pipe.c:632
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:874 [inline]
__se_sys_ioctl fs/ioctl.c:860 [inline]
__x64_sys_ioctl+0x193/0x200 fs/ioctl.c:860
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
Fixes: c73be61ced ("pipe: Add general notification queue support")
Reported-and-tested-by: syzbot+d55757faa9b80590767b@syzkaller.appspotmail.com
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e92936746 ]
The fix for not advancing the iterator if we're using fixed buffers is
broken in that it can hit a condition where we don't terminate the loop.
This results in io-wq looping forever, asking to read (or write) 0 bytes
for every subsequent loop.
Reported-by: Joel Jaeschke <joel.jaeschke@gmail.com>
Link: https://github.com/axboe/liburing/issues/549
Fixes: 16c8d2df7e ("io_uring: ensure symmetry in handling iter types in loop_rw_iter()")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a861abcee ]
__setup() handlers should return 1 to obsolete_checksetup() in
init/main.c to indicate that the boot option has been handled.
A return of 0 causes the boot option/value to be listed as an Unknown
kernel parameter and added to init's (limited) environment strings.
The __setup() handler interface isn't meant to handle negative return
values -- they are non-zero, so they mean "handled" (like a return
value of 1 does), but that's just a quirk. So return 1 from
parse_pmtmr(). Also print a warning message if kstrtouint() returns
an error.
Fixes: 6b148507d3 ("pmtmr: allow command line override of ioport")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru>
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5436af598 ]
If there is an input undervoltage fault, reported in STATUS_INPUT
command response, there is quite likely a "Unit Off For Insufficient
Input Voltage" condition as well.
Add a constant for bit 3 of STATUS_INPUT. Update the Vin limit
attributes to include both bits in the mask for clearing faults.
If an input undervoltage fault occurs, causing a unit off for
insufficient input voltage, but the unit is off bit is not cleared, the
STATUS_WORD will not be updated to clear the input fault condition.
Including the unit is off bit (bit 3) allows for the input fault
condition to completely clear.
Signed-off-by: Brandon Wyman <bjwyman@gmail.com>
Link: https://lore.kernel.org/r/20220317232123.2103592-1-bjwyman@gmail.com
Fixes: b4ce237b7f ("hwmon: (pmbus) Introduce infrastructure to detect sensors and limit registers")
[groeck: Dropped unnecessary ()]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f0f1f3ef6 ]
The corresponding API for clk_prepare_enable is clk_disable_unprepare,
other than clk_disable_unprepare.
Fix this by changing clk_disable to clk_disable_unprepare.
Fixes: beca35d05c ("hwrng: nomadik - use clk_prepare_enable()")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d950c3407 ]
kfree_sensitive(ctx_p->user.key) will free the ctx_p->user.key. But
ctx_p->user.key is still used in the next line, which will lead to a
use after free.
We can call kfree_sensitive() after dev_dbg() to avoid the uaf.
Fixes: 63ee04c8b4 ("crypto: ccree - add skcipher support")
Signed-off-by: Jianglei Nie <niejianglei2021@163.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54cce8ecb9 ]
ccp_dmaengine_register adds dma_chan->device_node to dma_dev->channels list
but ccp_dmaengine_unregister didn't remove them.
That can cause crashes in various dmaengine methods that tries to use dma_dev->channels
Fixes: 58ea8abf49 ("crypto: ccp - Register the CCP as a DMA...")
Signed-off-by: Dāvis Mosāns <davispuh@gmail.com>
Acked-by: John Allen <john.allen@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3303ff649 ]
__setup() handlers should return 1 to indicate that the boot option
has been handled. Returning 0 causes a boot option to be listed in
the Unknown kernel command line parameters and also added to init's
arg list (if no '=' sign) or environment list (if of the form 'a=b').
Unknown kernel command line parameters "erst_disable
bert_disable hest_disable BOOT_IMAGE=/boot/bzImage-517rc6", will be
passed to user space.
Run /sbin/init as init process
with arguments:
/sbin/init
erst_disable
bert_disable
hest_disable
with environment:
HOME=/
TERM=linux
BOOT_IMAGE=/boot/bzImage-517rc6
Fixes: a3e2acc5e3 ("ACPI / APEI: Add Boot Error Record Table (BERT) support")
Fixes: a08f82d080 ("ACPI, APEI, Error Record Serialization Table (ERST) support")
Fixes: 9dc9666416 ("ACPI, APEI, HEST table parsing")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru>
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru
Reviewed-by: "Huang, Ying" <ying.huang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab8da93dc0 ]
The driver statically defines maximum number of interrupts it can
handle, however it does not respect that limit when configuring them.
When provided with a DTS with more interrupts than assumed, the driver
will overwrite static array mct_irqs leading to silent memory
corruption.
Validate the interrupts coming from DTS to avoid this. This does not
change the fact that such DTS might not boot at all, because it is
simply incompatible, however at least some warning will be printed.
Fixes: 36ba5d527e ("ARM: EXYNOS: add device tree support for MCT controller driver")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Link: https://lore.kernel.org/r/20220220103815.135380-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 647d41d395 ]
vmx-crypto module depends on CRYPTO_AES, CRYPTO_CBC, CRYPTO_CTR or
CRYPTO_XTS, thus add them.
These dependencies are likely to be enabled, but if
CRYPTO_DEV_VMX=y && !CRYPTO_MANAGER_DISABLE_TESTS
and either of CRYPTO_AES, CRYPTO_CBC, CRYPTO_CTR or CRYPTO_XTS is built
as module or disabled, alg_test() from crypto/testmgr.c complains during
boot about failing to allocate the generic fallback implementations
(2 == ENOENT):
[ 0.540953] Failed to allocate xts(aes) fallback: -2
[ 0.541014] alg: skcipher: failed to allocate transform for p8_aes_xts: -2
[ 0.541120] alg: self-tests for p8_aes_xts (xts(aes)) failed (rc=-2)
[ 0.544440] Failed to allocate ctr(aes) fallback: -2
[ 0.544497] alg: skcipher: failed to allocate transform for p8_aes_ctr: -2
[ 0.544603] alg: self-tests for p8_aes_ctr (ctr(aes)) failed (rc=-2)
[ 0.547992] Failed to allocate cbc(aes) fallback: -2
[ 0.548052] alg: skcipher: failed to allocate transform for p8_aes_cbc: -2
[ 0.548156] alg: self-tests for p8_aes_cbc (cbc(aes)) failed (rc=-2)
[ 0.550745] Failed to allocate transformation for 'aes': -2
[ 0.550801] alg: cipher: Failed to load transform for p8_aes: -2
[ 0.550892] alg: self-tests for p8_aes (aes) failed (rc=-2)
Fixes: c07f5d3da6 ("crypto: vmx - Adding support for XTS")
Fixes: d2e3ae6f3a ("crypto: vmx - Enabling VMX module for PPC64")
Suggested-by: Nicolai Stange <nstange@suse.de>
Signed-off-by: Petr Vorel <pvorel@suse.cz>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a64ca17e4 ]
If an invalid option is given for "test_suspend=<option>", the entire
string is added to init's environment, so return 1 instead of 0 from
the __setup handler.
Unknown kernel command line parameters "BOOT_IMAGE=/boot/bzImage-517rc5
test_suspend=invalid"
and
Run /sbin/init as init process
with arguments:
/sbin/init
with environment:
HOME=/
TERM=linux
BOOT_IMAGE=/boot/bzImage-517rc5
test_suspend=invalid
Fixes: 2ce986892f ("PM / sleep: Enhance test_suspend option with repeat capability")
Fixes: 27ddcc6596 ("PM / sleep: Add state field to pm_states[] entries")
Fixes: a9d7052363 ("PM: Separate suspend to RAM functionality from core")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru>
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f69288253 ]
kobjects aren't supposed to be deleted before their child kobjects are
deleted. Apparently this is usually benign; however, a WARN will be
triggered if one of the child kobjects has a named attribute group:
sysfs group 'modes' not found for kobject 'crypto'
WARNING: CPU: 0 PID: 1 at fs/sysfs/group.c:278 sysfs_remove_group+0x72/0x80
...
Call Trace:
sysfs_remove_groups+0x29/0x40 fs/sysfs/group.c:312
__kobject_del+0x20/0x80 lib/kobject.c:611
kobject_cleanup+0xa4/0x140 lib/kobject.c:696
kobject_release lib/kobject.c:736 [inline]
kref_put include/linux/kref.h:65 [inline]
kobject_put+0x53/0x70 lib/kobject.c:753
blk_crypto_sysfs_unregister+0x10/0x20 block/blk-crypto-sysfs.c:159
blk_unregister_queue+0xb0/0x110 block/blk-sysfs.c:962
del_gendisk+0x117/0x250 block/genhd.c:610
Fix this by moving the kobject_del() and the corresponding
kobject_uevent() to the correct place.
Fixes: 2c2086afc2 ("block: Protect less code with sysfs_lock in blk_{un,}register_queue()")
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20220124215938.2769-3-ebiggers@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd8099e791 ]
Pass the actual nvme_ns_ids used for the comparison instead of the
ns_head that isn't needed and use a more descriptive function name.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 647d6f09be ]
If the watchdog was already enabled by the BIOS after booting, the
watchdog infrastructure needs to regularly send keepalives to
prevent a unexpected reset.
WDOG_ACTIVE only serves as an status indicator for userspace,
we want to use WDOG_HW_RUNNING instead.
Since my Fujitsu Esprimo P720 does not support the watchdog,
this change is compile-tested only.
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Fixes: fb551405c0 (watchdog: sch56xx: Use watchdog core)
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20220131211935.3656-5-W_Armin@gmx.de
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1fb37b5692 ]
Refuse to try mapping zero bytes as this may cause a fault
on some configurations / platforms and it seems the prev.
attempt is not enough and we need to be more explicit.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Reported-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Fixes: ce0fc6db38 ("crypto: ccree - protect against empty or NULL
scatterlists")
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2544f5e6c ]
__setup() handlers should return 1 if the parameter is handled.
Returning 0 causes the entire string to be added to init's
environment strings (limited to 32 strings), unnecessarily polluting it.
Using the documented string "evm=fix" causes an Unknown parameter message:
Unknown kernel command line parameters
"BOOT_IMAGE=/boot/bzImage-517rc5 evm=fix", will be passed to user space.
and that string is added to init's environment string space:
Run /sbin/init as init process
with arguments:
/sbin/init
with environment:
HOME=/
TERM=linux
BOOT_IMAGE=/boot/bzImage-517rc5
evm=fix
With this change, using "evm=fix" acts as expected and an invalid
option ("evm=evm") causes a warning to be printed:
evm: invalid "evm" mode
but init's environment is not polluted with this string, as expected.
Fixes: 7102ebcd65 ("evm: permit only valid security.evm xattrs to be updated")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru>
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 272ceeaea3 ]
AUDIT_TIME_* events are generated when there are syscall rules present
that are not related to time keeping. This will produce noisy log
entries that could flood the logs and hide events we really care about.
Rather than immediately produce the AUDIT_TIME_* records, store the data
in the context and log it at syscall exit time respecting the filter
rules.
Note: This eats the audit_buffer, unlike any others in show_special().
Please see https://bugzilla.redhat.com/show_bug.cgi?id=1991919
Fixes: 7e8eda734d ("ntp: Audit NTP parameters adjustment")
Fixes: 2d87a0674b ("timekeeping: Audit clock adjustments")
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
[PM: fixed style/whitespace issues]
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 973d74e938 ]
When loading rockchip crypto module, testmgr complains that ivsize of ecb-des3-ede-rk
is not the same than generic implementation.
In fact ECB does not use an IV.
Fixes: ce0183cb64 ("crypto: rockchip - switch to skcipher API")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee017ee353 ]
The 'fixmap' is a global resource and is used recursively by
create pud mapping(), leading to a potential race condition in the
presence of a concurrent call to alloc_init_pud():
kernel_init thread virtio-mem workqueue thread
================== ===========================
alloc_init_pud(...) alloc_init_pud(...)
pudp = pud_set_fixmap_offset(...) pudp = pud_set_fixmap_offset(...)
READ_ONCE(*pudp)
pud_clear_fixmap(...)
READ_ONCE(*pudp) // CRASH!
As kernel may sleep during creating pud mapping, introduce a mutex lock to
serialise use of the fixmap entries by alloc_init_pud(). However, there is
no need for locking in early boot stage and it doesn't work well with
KASLR enabled when early boot. So, enable lock when system_state doesn't
equal to "SYSTEM_BOOTING".
Signed-off-by: Jianyong Wu <jianyong.wu@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Fixes: f471044545 ("arm64: mm: use fixmap when creating page tables")
Link: https://lore.kernel.org/r/20220201114400.56885-1-jianyong.wu@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f92724d4b ]
This func misses checking for platform_get_irq()'s call and may passes the
negative error codes to request_threaded_irq(), which takes unsigned IRQ #,
causing it to fail with -EINVAL, overriding an original error code.
Stop calling request_threaded_irq() with invalid IRQ #s.
Fixes: f333a331ad ("spi/tegra114: add spi driver")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220128165238.25615-1-linmq006@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 38b16d6cfe ]
As the potential failure of the allocation, kmemdup() may return NULL.
Then, 'bin_attr_data_vault.private' will be NULL, but
'bin_attr_data_vault.size' is not 0, which is not consistent.
Therefore, it is better to check the return value of kmemdup() to
avoid the confusion.
Fixes: 0ba13c763a ("thermal/int340x_thermal: Export GDDV")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28e9b6d819 ]
This patch fixes a bug in scatterlist processing that may cause incorrect AES block encryption/decryption.
Fixes: 2e6d793e1b ("crypto: mxs-dcp - Use sg_mapping_iter to copy data")
Signed-off-by: Tomas Paukrt <tomaspaukrt@email.cz>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66eae85033 ]
The function crypto_authenc_decrypt_tail discards its flags
argument and always relies on the flags from the original request
when starting its sub-request.
This is clearly wrong as it may cause the SLEEPABLE flag to be
set when it shouldn't.
Fixes: 92d95ba917 ("crypto: authenc - Convert to new AEAD interface")
Reported-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 881fc7fba6 ]
When adding hashes support to sun8i-ss, I have added them only on A83T.
But I forgot that 0 is a valid algorithm ID, so hashes are enabled on A80 but
with an incorrect ID.
Anyway, even with correct IDs, hashes do not work on A80 and I cannot
find why.
So let's disable all of them on A80.
Fixes: d9b45418a9 ("crypto: sun8i-ss - support hash algorithms")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab7d88549e ]
The Cavium ThunderX Random Number Generator is only present on Cavium
ThunderX SoCs, and not available as an independent PCIe endpoint. Hence
add a dependency on ARCH_THUNDER, to prevent asking the user about this
driver when configuring a kernel without Cavium Thunder SoC support.
Fixes: cc2f1908c6 ("hwrng: cavium - Add Cavium HWRNG driver for ThunderX SoC.")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 680efb3354 ]
This RNG device is present on Marvell OcteonTx2 silicons as well and
also provides entropy health status.
HW continuously checks health condition of entropy and reports
faults. Fault is in terms of co-processor cycles since last fault
detected. This doesn't get cleared and only updated when new fault
is detected. Also there are chances of detecting false positives.
So to detect a entropy failure SW has to check if failures are
persistent ie cycles elapsed is frequently updated by HW.
This patch adds support to detect health failures using below algo.
1. Consider any fault detected before 10ms as a false positive and ignore.
10ms is chosen randomly, no significance.
2. Upon first failure detection make a note of cycles elapsed and when this
error happened in realtime (cntvct).
3. Upon subsequent failure, check if this is new or a old one by comparing
current cycles with the ones since last failure. cycles or time since
last failure is calculated using cycles and time info captured at (2).
HEALTH_CHECK status register is not available to VF, hence had to map
PF registers. Also since cycles are in terms of co-processor cycles,
had to retrieve co-processor clock rate from RST device.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bcb62828e3 ]
sel_make_avc_files() might fail and return a negative errno value on
memory allocation failures. Re-add the check of the return value,
dropped in 66f8e2f03c ("selinux: sidtab reverse lookup hash table").
Reported by clang-analyzer:
security/selinux/selinuxfs.c:2129:2: warning: Value stored to
'ret' is never read [deadcode.DeadStores]
ret = sel_make_avc_files(dentry);
^ ~~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: 66f8e2f03c ("selinux: sidtab reverse lookup hash table")
Signed-off-by: Christian Göttsche <cgzones@googlemail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
[PM: description line wrapping, added proper commit ref]
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6390d42c21 ]
drivers/regulator/qcom_smd-regulator.c:1318:1-33: WARNING: Function "for_each_available_child_of_node" should have of_node_put() before return around line 1321.
Semantic patch information:
False positives can be due to function calls within the for_each
loop that may encapsulate an of_node_put.
Generated by: scripts/coccinelle/iterators/for_each_child.cocci
Fixes: 14e2976fba ("regulator: qcom_smd: Align probe function with rpmh-regulator")
CC: Konrad Dybcio <konrad.dybcio@somainline.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: kernel test robot <lkp@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@inria.fr>
Link: https://lore.kernel.org/r/alpine.DEB.2.22.394.2201151210170.3051@hadrien
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 92912b1751 upstream.
Writes to a Downstream Port's Slot Control register are PCIe hotplug
"commands." If the Port supports Command Completed events, software must
wait for a command to complete before writing to Slot Control again.
pcie_do_write_cmd() sets ctrl->cmd_busy when it writes to Slot Control. If
software notification is enabled, i.e., PCI_EXP_SLTCTL_HPIE and
PCI_EXP_SLTCTL_CCIE are set, ctrl->cmd_busy is cleared by pciehp_isr().
But when software notification is disabled, as it is when pcie_init()
powers off an empty slot, pcie_wait_cmd() uses pcie_poll_cmd() to poll for
command completion, and it neglects to clear ctrl->cmd_busy, which leads to
spurious timeouts:
pcieport 0000:00:03.0: pciehp: Timeout on hotplug command 0x01c0 (issued 2264 msec ago)
pcieport 0000:00:03.0: pciehp: Timeout on hotplug command 0x05c0 (issued 2288 msec ago)
Clear ctrl->cmd_busy in pcie_poll_cmd() when it detects a Command Completed
event (PCI_EXP_SLTSTA_CC).
[bhelgaas: commit log]
Fixes: a5dd4b4b05 ("PCI: pciehp: Wait for hotplug command completion where necessary")
Link: https://lore.kernel.org/r/20211111054258.7309-1-zhangliguang@linux.alibaba.com
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215143
Link: https://lore.kernel.org/r/20211126173309.GA12255@wunner.de
Signed-off-by: Liguang Zhang <zhangliguang@linux.alibaba.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a3d0245c58 upstream.
The commit cad6fade6e ("xtensa: clean up WSR*/RSR*/get_sr/set_sr")
replaced 'WSR' macro in the function xtensa_wsr with 'xtensa_set_sr',
but variable 'v' in the xtensa_set_sr body shadowed the argument 'v'
passed to it, resulting in wrong value written to debug registers.
Fix that by removing intermediate variable from the xtensa_set_sr
macro body.
Cc: stable@vger.kernel.org
Fixes: cad6fade6e ("xtensa: clean up WSR*/RSR*/get_sr/set_sr")
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f406f2d03e upstream.
patch_text must invoke patch_text_stop_machine on all online CPUs, but
it calls stop_machine_cpuslocked with NULL cpumask. As a result only one
CPU runs patch_text_stop_machine potentially leaving stale icache
entries on other CPUs. Fix that by calling stop_machine_cpuslocked with
cpu_online_mask as the last argument.
Cc: stable@vger.kernel.org
Fixes: 64711f9a47 ("xtensa: implement jump_label support")
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 244eae91a9 upstream.
Recent tightening of the opcode table in binutils so as to consistently
disallow the assembly or disassembly of CP0 instructions not supported
by the processor architecture chosen has caused a regression like below:
arch/mips/dec/prom/locore.S: Assembler messages:
arch/mips/dec/prom/locore.S:29: Error: opcode not supported on this processor: r4600 (mips3) `rfe'
in a piece of code used to probe for memory with PMAX DECstation models,
which have non-REX firmware. Those computers always have an R2000 CPU
and consequently the exception handler used in memory probing uses the
RFE instruction, which those processors use.
While adding 64-bit support this code was correctly excluded for 64-bit
configurations, however it should have also been excluded for irrelevant
32-bit configurations. Do this now then, and only enable PMAX memory
probing for R3k systems.
Reported-by: Jan-Benedict Glaw <jbglaw@lug-owl.de>
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org # v2.6.12+
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 887554ab96 upstream.
When multiple threads to check btree nodes in parallel, the main
thread wait for all threads to stop or CACHE_SET_IO_DISABLE flag:
wait_event_interruptible(check_state->wait,
atomic_read(&check_state->started) == 0 ||
test_bit(CACHE_SET_IO_DISABLE, &c->flags));
However, the bch_btree_node_read and bch_btree_node_read_done
maybe call bch_cache_set_error, then the CACHE_SET_IO_DISABLE
will be set. If the flag already set, the main thread return
error. At the same time, maybe some threads still running and
read NULL pointer, the kernel will crash.
This patch change the event wait condition, the main thread must
wait for all threads to stop.
Fixes: 8e7102273f ("bcache: make bch_btree_check() to be multithreaded")
Signed-off-by: Mingzhe Zou <mingzhe.zou@easystack.cn>
Cc: stable@vger.kernel.org # v5.7+
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3481accd9 upstream.
RSA PKCS#1 v1.5 signatures are required to be the same length as the RSA
key size. RFC8017 specifically requires the verifier to check this
(https://datatracker.ietf.org/doc/html/rfc8017#section-8.2.2).
Commit a49de377e0 ("crypto: Add hash param to pkcs1pad") changed the
kernel to allow longer signatures, but didn't explain this part of the
change; it seems to be unrelated to the rest of the commit.
Revert this change, since it doesn't appear to be correct.
We can be pretty sure that no one is relying on overly-long signatures
(which would have to be front-padded with zeroes) being supported, given
that they would have been broken since commit c7381b0128
("crypto: akcipher - new verify API for public key algorithms").
Fixes: a49de377e0 ("crypto: Add hash param to pkcs1pad")
Cc: <stable@vger.kernel.org> # v4.6+
Cc: Tadeusz Struk <tadeusz.struk@linaro.org>
Suggested-by: Vitaly Chikunov <vt@altlinux.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e316f7179b upstream.
Commit c7381b0128 ("crypto: akcipher - new verify API for public key
algorithms") changed akcipher_alg::verify to take in both the signature
and the actual hash and do the signature verification, rather than just
return the hash expected by the signature as was the case before. To do
this, it implemented a hack where the signature and hash are
concatenated with each other in one scatterlist.
Obviously, for this to work correctly, akcipher_alg::verify needs to
correctly extract the two items from the scatterlist it is given.
Unfortunately, it doesn't correctly extract the hash in the case where
the signature is longer than the RSA key size, as it assumes that the
signature's length is equal to the RSA key size. This causes a prefix
of the hash, or even the entire hash, to be taken from the *signature*.
(Note, the case of a signature longer than the RSA key size should not
be allowed in the first place; a separate patch will fix that.)
It is unclear whether the resulting scheme has any useful security
properties.
Fix this by correctly extracting the hash from the scatterlist.
Fixes: c7381b0128 ("crypto: akcipher - new verify API for public key algorithms")
Cc: <stable@vger.kernel.org> # v5.2+
Reviewed-by: Vitaly Chikunov <vt@altlinux.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b30430ea3 upstream.
The pkcs1pad template can be instantiated with an arbitrary akcipher
algorithm, which doesn't make sense; it is specifically an RSA padding
scheme. Make it check that the underlying algorithm really is RSA.
Fixes: 3d5b1ecdea ("crypto: rsa - RSA padding algorithm")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5359ddd05 upstream.
GCC 10+ defaults to -fno-common, which enforces proper declaration of
external references using "extern". without this change a link would
fail with:
lib/raid6/test/algos.c:28: multiple definition of `raid6_call';
lib/raid6/test/test.c:22: first defined here
the pq.h header that is included already includes an extern declaration
so we can just remove the redundant one here.
Cc: <stable@vger.kernel.org>
Signed-off-by: Dirk Müller <dmueller@suse.de>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Song Liu <song@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8126b1c731 upstream.
pstore_dump() is *always* invoked in atomic context (nowadays in an RCU
read-side critical section, before that under a spinlock).
It doesn't make sense to try to use semaphores here.
This is mostly a revert of commit ea84b580b9 ("pstore: Convert buf_lock
to semaphore"), except that two parts aren't restored back exactly as they
were:
- keep the lock initialization in pstore_register
- in efi_pstore_write(), always set the "block" flag to false
- omit "is_locked", that was unnecessary since
commit 959217c84c ("pstore: Actually give up during locking failure")
- fix the bailout message
The actual problem that the buggy commit was trying to address may have
been that the use of preemptible() in efi_pstore_write() was wrong - it
only looks at preempt_count() and the state of IRQs, but __rcu_read_lock()
doesn't touch either of those under CONFIG_PREEMPT_RCU.
(Sidenote: CONFIG_PREEMPT_RCU means that the scheduler can preempt tasks in
RCU read-side critical sections, but you're not allowed to actively
block/reschedule.)
Lockdep probably never caught the problem because it's very rare that you
actually hit the contended case, so lockdep always just sees the
down_trylock(), not the down_interruptible(), and so it can't tell that
there's a problem.
Fixes: ea84b580b9 ("pstore: Convert buf_lock to semaphore")
Cc: stable@vger.kernel.org
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20220314185953.2068993-1-jannh@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 028a73e107 upstream.
On some servers with MGA G200_SE_A (rev 42), booting with Legacy BIOS,
the hardware hangs when using kdump and kexec into the kdump kernel.
This happens when the uncompress code tries to write "Decompressing Linux"
to the VGA Console.
It can be reproduced by writing to the VGA console (0xB8000) after
booting to graphic mode, it generates the following error:
kernel:NMI: PCI system error (SERR) for reason a0 on CPU 0.
kernel:Dazed and confused, but trying to continue
The root cause is the configuration of the MGA GCTL6 register
According to the GCTL6 register documentation:
bit 0 is gcgrmode:
0: Enables alpha mode, and the character generator addressing system is
activated.
1: Enables graphics mode, and the character addressing system is not
used.
bit 1 is chainodd even:
0: The A0 signal of the memory address bus is used during system memory
addressing.
1: Allows A0 to be replaced by either the A16 signal of the system
address (ifmemmapsl is ‘00’), or by the hpgoddev (MISC<5>, odd/even
page select) field, described on page 3-294).
bit 3-2 are memmapsl:
Memory map select bits 1 and 0. VGA.
These bits select where the video memory is mapped, as shown below:
00 => A0000h - BFFFFh
01 => A0000h - AFFFFh
10 => B0000h - B7FFFh
11 => B8000h - BFFFFh
bit 7-4 are reserved.
Current code set it to 0x05 => memmapsl to b01 => 0xa0000 (graphic mode)
But on x86, the VGA console is at 0xb8000 (text mode)
In arch/x86/boot/compressed/misc.c debug strings are written to 0xb8000
As the driver doesn't use this mapping at 0xa0000, it is safe to set it to
0xb8000 instead, to avoid kernel hang on G200_SE_A rev42, with kexec/kdump.
Thus changing the value 0x05 to 0x0d
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220119102905.1194787-1-jfalempe@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd771cf5c4 upstream.
Zheyu Ma reported this crash in the sm712fb driver when reading
three bytes from the framebuffer:
BUG: unable to handle page fault for address: ffffc90001ffffff
RIP: 0010:smtcfb_read+0x230/0x3e0
Call Trace:
vfs_read+0x198/0xa00
? do_sys_openat2+0x27d/0x350
? __fget_light+0x54/0x340
ksys_read+0xce/0x190
do_syscall_64+0x43/0x90
Fix it by removing the open-coded endianess fixup-code and
by moving the pointer post decrement out the fb_readl() function.
Reported-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Tested-by: Zheyu Ma <zheyuma97@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b2b04590b upstream.
blk-iocost and iolatency are cgroup aware rq-qos policies but they didn't
disable merges across different cgroups. This obviously can lead to
accounting and control errors but more importantly to priority inversions -
e.g. an IO which belongs to a higher priority cgroup or IO class may end up
getting throttled incorrectly because it gets merged to an IO issued from a
low priority cgroup.
Fix it by adding blk_cgroup_mergeable() which is called from merge paths and
rejects cross-cgroup and cross-issue_as_root merges.
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: d706751215 ("block: introduce blk-iolatency io controller")
Cc: stable@vger.kernel.org # v4.19+
Cc: Josef Bacik <jbacik@fb.com>
Link: https://lore.kernel.org/r/Yi/eE/6zFNyWJ+qd@slm.duckdns.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit efe4186e6a upstream.
When a 6pack device is detaching, the sixpack_close() will act to cleanup
necessary resources. Although del_timer_sync() in sixpack_close()
won't return if there is an active timer, one could use mod_timer() in
sp_xmit_on_air() to wake up timer again by calling userspace syscall such
as ax25_sendmsg(), ax25_connect() and ax25_ioctl().
This unexpected waked handler, sp_xmit_on_air(), realizes nothing about
the undergoing cleanup and may still call pty_write() to use driver layer
resources that have already been released.
One of the possible race conditions is shown below:
(USE) | (FREE)
ax25_sendmsg() |
ax25_queue_xmit() |
... |
sp_xmit() |
sp_encaps() | sixpack_close()
sp_xmit_on_air() | del_timer_sync(&sp->tx_t)
mod_timer(&sp->tx_t,...) | ...
| unregister_netdev()
| ...
(wait a while) | tty_release()
| tty_release_struct()
| release_tty()
sp_xmit_on_air() | tty_kref_put(tty_struct) //FREE
pty_write(tty_struct) //USE | ...
The corresponding fail log is shown below:
===============================================================
BUG: KASAN: use-after-free in __run_timers.part.0+0x170/0x470
Write of size 8 at addr ffff88800a652ab8 by task swapper/2/0
...
Call Trace:
...
queue_work_on+0x3f/0x50
pty_write+0xcd/0xe0pty_write+0xcd/0xe0
sp_xmit_on_air+0xb2/0x1f0
call_timer_fn+0x28/0x150
__run_timers.part.0+0x3c2/0x470
run_timer_softirq+0x3b/0x80
__do_softirq+0xf1/0x380
...
This patch reorders the del_timer_sync() after the unregister_netdev()
to avoid UAF bugs. Because the unregister_netdev() is well synchronized,
it flushs out any pending queues, waits the refcount of net_device
decreases to zero and removes net_device from kernel. There is not any
running routines after executing unregister_netdev(). Therefore, we could
not arouse timer from userspace again.
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7aab5c84a0 upstream.
We inject IO error when rmdir non empty direcory, then got issue as follows:
step1: mkfs.ext4 -F /dev/sda
step2: mount /dev/sda test
step3: cd test
step4: mkdir -p 1/2
step5: rmdir 1
[ 110.920551] ext4_empty_dir: inject fault
[ 110.921926] EXT4-fs warning (device sda): ext4_rmdir:3113: inode #12:
comm rmdir: empty directory '1' has too many links (3)
step6: cd ..
step7: umount test
step8: fsck.ext4 -f /dev/sda
e2fsck 1.42.9 (28-Dec-2013)
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Entry '..' in .../??? (13) has deleted/unused inode 12. Clear<y>? yes
Pass 3: Checking directory connectivity
Unconnected directory inode 13 (...)
Connect to /lost+found<y>? yes
Pass 4: Checking reference counts
Inode 13 ref count is 3, should be 2. Fix<y>? yes
Pass 5: Checking group summary information
/dev/sda: ***** FILE SYSTEM WAS MODIFIED *****
/dev/sda: 12/131072 files (0.0% non-contiguous), 26157/524288 blocks
ext4_rmdir
if (!ext4_empty_dir(inode))
goto end_rmdir;
ext4_empty_dir
bh = ext4_read_dirblock(inode, 0, DIRENT_HTREE);
if (IS_ERR(bh))
return true;
Now if read directory block failed, 'ext4_empty_dir' will return true, assume
directory is empty. Obviously, it will lead to above issue.
To solve this issue, if read directory block failed 'ext4_empty_dir' just
return false. To avoid making things worse when file system is already
corrupted, 'ext4_empty_dir' also return false.
Signed-off-by: Ye Bin <yebin10@huawei.com>
Cc: stable@kernel.org
Link: https://lore.kernel.org/r/20220228024815.3952506-1-yebin10@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84158b7f6a upstream.
When I rewrote the VMA dumping logic for coredumps, I changed it to
recognize ELF library mappings based on the file being executable instead
of the mapping having an ELF header. But turns out, distros ship many ELF
libraries as non-executable, so the heuristic goes wrong...
Restore the old behavior where FILTER(ELF_HEADERS) dumps the first page of
any offset-0 readable mapping that starts with the ELF magic.
This fix is technically layer-breaking a bit, because it checks for
something ELF-specific in fs/coredump.c; but since we probably want to
share this between standard ELF and FDPIC ELF anyway, I guess it's fine?
And this also keeps the change small for backporting.
Cc: stable@vger.kernel.org
Fixes: 429a22e776 ("coredump: rework elf/elf_fdpic vma_dump_size() into common helper")
Reported-by: Bill Messmer <wmessmer@microsoft.com>
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20220126025739.2014888-1-jannh@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit babc92da59 upstream.
__acpi_node_get_property_reference() is documented to return -ENOENT if
the caller requests a property reference at an index that does not exist,
not -EINVAL which it actually does.
Fix this by returning -ENOENT consistenly, independently of whether the
property value is a plain reference or a package.
Fixes: c343bc2ce2 ("ACPI: properties: Align return codes of __acpi_node_get_property_reference()")
Cc: 4.14+ <stable@vger.kernel.org> # 4.14+
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0a32c88ddb upstream.
Commit 6d502b6ba1 ("arm64: signal: nofpsimd: Handle fp/simd context for
signal frames") introduced saving the fp/simd context for signal handling
only when support is available. But setup_sigframe_layout() always
reserves memory for fp/simd context. The additional memory is not touched
because preserve_fpsimd_context() is not called and thus the magic is
invalid.
This may lead to an error when parse_user_sigframe() checks the fp/simd
area and does not find a valid magic number.
Signed-off-by: David Engraf <david.engraf@sysgo.com>
Reviwed-by: Mark Brown <broonie@kernel.org>
Fixes: 6d502b6ba1 ("arm64: signal: nofpsimd: Handle fp/simd context for signal frames")
Cc: <stable@vger.kernel.org> # 5.6.x
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20220225104008.820289-1-david.engraf@sysgo.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4a600dd30 upstream.
When enabling encap for a ipv6 socket without udp_encap_needed_key
increased, UDP GRO won't work for v4 mapped v6 address packets as
sk will be NULL in udp4_gro_receive().
This patch is to enable it by increasing udp_encap_needed_key for
v6 sockets in udp_tunnel_encap_enable(), and correspondingly
decrease udp_encap_needed_key in udpv6_destroy_sock().
v1->v2:
- add udp_encap_disable() and export it.
v2->v3:
- add the change for rxrpc and bareudp into one patch, as Alex
suggested.
v3->v4:
- move rxrpc part to another patch.
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tested-by: Antonio Quartulli <antonio@openvpn.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f4329d1f84 upstream.
Scenario:
---------
bio chain generated by blk_queue_split().
Some split bio fails and propagates its error status to the "parent" bio.
But then the (last part of the) parent bio itself completes without error.
We would clobber the already recorded error status with BLK_STS_OK,
causing silent data corruption.
Reproducer:
-----------
How to trigger this in the real world within seconds:
DRBD on top of degraded parity raid,
small stripe_cache_size, large read_ahead setting.
Drop page cache (sysctl vm.drop_caches=1, fadvise "DONTNEED",
umount and mount again, "reboot").
Cause significant read ahead.
Large read ahead request is split by blk_queue_split().
Parts of the read ahead that are already in the stripe cache,
or find an available stripe cache to use, can be serviced.
Parts of the read ahead that would need "too much work",
would need to wait for a "stripe_head" to become available,
are rejected immediately.
For larger read ahead requests that are split in many pieces, it is very
likely that some "splits" will be serviced, but then the stripe cache is
exhausted/busy, and the remaining ones will be rejected.
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Cc: <stable@vger.kernel.org> # 4.13.x
Link: https://lore.kernel.org/r/20220330185551.3553196-1-christoph.boehmwalder@linbit.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc09e8a9de upstream.
Commit f6f72f32c2 ("dm integrity: don't replay journal data past the
end of the device") skips journal replay if the target sector points
beyond the end of the device. Unfortunatelly, it doesn't set the
journal entry unused, which resulted in this BUG being triggered:
BUG_ON(!journal_entry_is_unused(je))
Fix this by calling journal_entry_set_unused() for this case.
Fixes: f6f72f32c2 ("dm integrity: don't replay journal data past the end of the device")
Cc: stable@vger.kernel.org # v5.7+
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Tested-by: Milan Broz <gmazyland@gmail.com>
[snitzer: revised header]
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bfc8089f00 upstream.
When we use HW-tag based kasan and enable vmalloc support, we hit the
following bug. It is due to comparison between tagged object and
non-tagged pointer.
We need to reset the kasan tag when we need to compare tagged object and
non-tagged pointer.
kmemleak: [name:kmemleak&]Scan area larger than object 0xffffffe77076f440
CPU: 4 PID: 1 Comm: init Tainted: G S W 5.15.25-android13-0-g5cacf919c2bc #1
Hardware name: MT6983(ENG) (DT)
Call trace:
add_scan_area+0xc4/0x244
kmemleak_scan_area+0x40/0x9c
layout_and_allocate+0x1e8/0x288
load_module+0x2c8/0xf00
__se_sys_finit_module+0x190/0x1d0
__arm64_sys_finit_module+0x20/0x30
invoke_syscall+0x60/0x170
el0_svc_common+0xc8/0x114
do_el0_svc+0x28/0xa0
el0_svc+0x60/0xf8
el0t_64_sync_handler+0x88/0xec
el0t_64_sync+0x1b4/0x1b8
kmemleak: [name:kmemleak&]Object 0xf5ffffe77076b000 (size 32768):
kmemleak: [name:kmemleak&] comm "init", pid 1, jiffies 4294894197
kmemleak: [name:kmemleak&] min_count = 0
kmemleak: [name:kmemleak&] count = 0
kmemleak: [name:kmemleak&] flags = 0x1
kmemleak: [name:kmemleak&] checksum = 0
kmemleak: [name:kmemleak&] backtrace:
module_alloc+0x9c/0x120
move_module+0x34/0x19c
layout_and_allocate+0x1c4/0x288
load_module+0x2c8/0xf00
__se_sys_finit_module+0x190/0x1d0
__arm64_sys_finit_module+0x20/0x30
invoke_syscall+0x60/0x170
el0_svc_common+0xc8/0x114
do_el0_svc+0x28/0xa0
el0_svc+0x60/0xf8
el0t_64_sync_handler+0x88/0xec
el0t_64_sync+0x1b4/0x1b8
Link: https://lkml.kernel.org/r/20220318034051.30687-1-Kuan-Ying.Lee@mediatek.com
Signed-off-by: Kuan-Ying Lee <Kuan-Ying.Lee@mediatek.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Chinwen Chang <chinwen.chang@mediatek.com>
Cc: Nicholas Tang <nicholas.tang@mediatek.com>
Cc: Yee Lee <yee.lee@mediatek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3149c79f3c upstream.
In some cases it appears the invalidation of a hwpoisoned page fails
because the page is still mapped in another process. This can cause a
program to be continuously restarted and die when it page faults on the
page that was not invalidated. Avoid that problem by unmapping the
hwpoisoned page when we find it.
Another issue is that sometimes we end up oopsing in finish_fault, if
the code tries to do something with the now-NULL vmf->page. I did not
hit this error when submitting the previous patch because there are
several opportunities for alloc_set_pte to bail out before accessing
vmf->page, and that apparently happened on those systems, and most of
the time on other systems, too.
However, across several million systems that error does occur a handful
of times a day. It can be avoided by returning VM_FAULT_NOPAGE which
will cause do_read_fault to return before calling finish_fault.
Link: https://lkml.kernel.org/r/20220325161428.5068d97e@imladris.surriel.com
Fixes: e53ac7374e ("mm: invalidate hwpoison page cache page in fault path")
Signed-off-by: Rik van Riel <riel@surriel.com>
Reviewed-by: Miaohe Lin <linmiaohe@huawei.com>
Tested-by: Naoya Horiguchi <naoya.horiguchi@nec.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5bd009c7c9 upstream.
Patch series "mm: madvise: return correct bytes processed with
process_madvise", v2. With the process_madvise(), always choose to return
non zero processed bytes over an error. This can help the user to know on
which VMA, passed in the 'struct iovec' vector list, is failed to advise
thus can take the decission of retrying/skipping on that VMA.
This patch (of 2):
The process_madvise() system call returns error even after processing some
VMA's passed in the 'struct iovec' vector list which leaves the user
confused to know where to restart the advise next. It is also against
this syscall man page[1] documentation where it mentions that "return
value may be less than the total number of requested bytes, if an error
occurred after some iovec elements were already processed.".
Consider a user passed 10 VMA's in the 'struct iovec' vector list of which
9 are processed but one. Then it just returns the error caused on that
failed VMA despite the first 9 VMA's processed, leaving the user confused
about on which VMA it is failed. Returning the number of bytes processed
here can help the user to know which VMA it is failed on and thus can
retry/skip the advise on that VMA.
[1]https://man7.org/linux/man-pages/man2/process_madvise.2.html.
Link: https://lkml.kernel.org/r/cover.1647008754.git.quic_charante@quicinc.com
Link: https://lkml.kernel.org/r/125b61a0edcee5c2db8658aed9d06a43a19ccafc.1647008754.git.quic_charante@quicinc.com
Fixes: ecb8ac8b1f14("mm/madvise: introduce process_madvise() syscall: an external memory hinting API")
Signed-off-by: Charan Teja Kalla <quic_charante@quicinc.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: David Rientjes <rientjes@google.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nadav Amit <nadav.amit@gmail.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc55cfd571 upstream.
syzbot caught a potential deadlock between the PCM
runtime->buffer_mutex and the mm->mmap_lock. It was brought by the
recent fix to cover the racy read/write and other ioctls, and in that
commit, I overlooked a (hopefully only) corner case that may take the
revert lock, namely, the OSS mmap. The OSS mmap operation
exceptionally allows to re-configure the parameters inside the OSS
mmap syscall, where mm->mmap_mutex is already held. Meanwhile, the
copy_from/to_user calls at read/write operations also take the
mm->mmap_lock internally, hence it may lead to a AB/BA deadlock.
A similar problem was already seen in the past and we fixed it with a
refcount (in commit b248371628). The former fix covered only the
call paths with OSS read/write and OSS ioctls, while we need to cover
the concurrent access via both ALSA and OSS APIs now.
This patch addresses the problem above by replacing the buffer_mutex
lock in the read/write operations with a refcount similar as we've
used for OSS. The new field, runtime->buffer_accessing, keeps the
number of concurrent read/write operations. Unlike the former
buffer_mutex protection, this protects only around the
copy_from/to_user() calls; the other codes are basically protected by
the PCM stream lock. The refcount can be a negative, meaning blocked
by the ioctls. If a negative value is seen, the read/write aborts
with -EBUSY. In the ioctl side, OTOH, they check this refcount, too,
and set to a negative value for blocking unless it's already being
accessed.
Reported-by: syzbot+6e5c88838328e99c7e1c@syzkaller.appspotmail.com
Fixes: dca947d4d2 ("ALSA: pcm: Fix races among concurrent read/write and buffer changes")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/000000000000381a0d05db622a81@google.com
Link: https://lore.kernel.org/r/20220330120903.4738-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ddc2f7496 upstream.
There is a corner case with unsol event handling during codec runtime
suspending state. When the codec runtime suspend call initiated, the
codec->in_pm atomic variable would be 0, currently the codec runtime
suspend function calls snd_hdac_enter_pm() which will just increments
the codec->in_pm atomic variable. Consider unsol event happened just
after this step and before snd_hdac_leave_pm() in the codec runtime
suspend function. The snd_hdac_power_up_pm() in the unsol event
flow in hdmi_present_sense_via_verbs() function would just increment
the codec->in_pm atomic variable without calling pm_runtime_get_sync
function.
As codec runtime suspend flow is already in progress and in parallel
unsol event is also accessing the codec verbs, as soon as codec
suspend flow completes and clocks are switched off before completing
the unsol event handling as both functions doesn't wait for each other.
This will result in below errors
[ 589.428020] tegra-hda 3510000.hda: azx_get_response timeout, switching
to polling mode: last cmd=0x505f2f57
[ 589.428344] tegra-hda 3510000.hda: spurious response 0x80000074:0x5,
last cmd=0x505f2f57
[ 589.428547] tegra-hda 3510000.hda: spurious response 0x80000065:0x5,
last cmd=0x505f2f57
To avoid this, the unsol event flow should not perform any codec verb
related operations during RPM_SUSPENDING state.
Signed-off-by: Mohan Kumar <mkumard@nvidia.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220329155940.26331-1-mkumard@nvidia.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0112f822f8 upstream.
The bug is here:
err = snd_card_cs423x_pnp(dev, card->private_data, pdev, cdev);
The list iterator value 'cdev' will *always* be set and non-NULL
by list_for_each_entry(), so it is incorrect to assume that the
iterator value will be NULL if the list is empty or no element
is found.
To fix the bug, use a new variable 'iter' as the list iterator,
while use the original variable 'cdev' as a dedicated pointer
to point to the found element. And snd_card_cs423x_pnp() itself
has NULL check for cdev.
Cc: stable@vger.kernel.org
Fixes: c2b73d1458 ("ALSA: cs4236: cs4232 and cs4236 driver merge to solve PnP BIOS detection")
Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com>
Link: https://lore.kernel.org/r/20220327060822.4735-1-xiam0nd.tong@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b188fba75 upstream.
This reverts commit 37ef4c19b4.
The touchpad present in the Dell Precision 7550 and 7750 laptops
reports a HID_DG_BUTTONTYPE of type MT_BUTTONTYPE_CLICKPAD. However,
the device is not a clickpad, it is a touchpad with physical buttons.
In order to fix this issue, a quirk for the device was introduced in
libinput [1] [2] to disable the INPUT_PROP_BUTTONPAD property:
[Precision 7x50 Touchpad]
MatchBus=i2c
MatchUdevType=touchpad
MatchDMIModalias=dmi:*svnDellInc.:pnPrecision7?50*
AttrInputPropDisable=INPUT_PROP_BUTTONPAD
However, because of the change introduced in 37ef4c19b4 ("Input: clear
BTN_RIGHT/MIDDLE on buttonpads") the BTN_RIGHT key bit is not mapped
anymore breaking the device right click button and making impossible to
workaround it in user space.
In order to avoid breakage on other present or future devices, revert
the patch causing the issue.
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220321184404.20025-1-jose.exposito89@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cbcc44db2c upstream.
Today when VFs are put in promiscuous mode, they can request PF
to configure device for them to receive all VLANs traffic regardless
of what vlan is configured by the PF (via ip link) and PF allows this
config request regardless of whether VF is trusted or not.
From security POV, when VLAN is configured for VF through PF (via ip link),
honour such config requests from VF only when they are configured to be
trusted, otherwise restrict such VFs vlan promisc mode config.
Cc: stable@vger.kernel.org
Fixes: f990c82c38 ("qed*: Add support for ndo_set_vf_trust")
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e0906008c upstream.
v2.6.34 commit 9d8cebd4bc ("mm: fix mbind vma merge problem") introduced
vma_merge() to mbind_range(); but unlike madvise, mlock and mprotect, it
put a "continue" to next vma where its precedents go to update flags on
current vma before advancing: that left vma with the wrong setting in the
infamous vma_merge() case 8.
v3.10 commit 1444f92c84 ("mm: merging memory blocks resets mempolicy")
tried to fix that in vma_adjust(), without fully understanding the issue.
v3.11 commit 3964acd0db ("mm: mempolicy: fix mbind_range() &&
vma_adjust() interaction") reverted that, and went about the fix in the
right way, but chose to optimize out an unnecessary mpol_dup() with a
prior mpol_equal() test. But on tmpfs, that also pessimized out the vital
call to its ->set_policy(), leaving the new mbind unenforced.
The user visible effect was that the pages got allocated on the local
node (happened to be 0), after the mbind() caller had specifically
asked for them to be allocated on node 1. There was not any page
migration involved in the case reported: the pages simply got allocated
on the wrong node.
Just delete that optimization now (though it could be made conditional on
vma not having a set_policy). Also remove the "next" variable: it turned
out to be blameless, but also pointless.
Link: https://lkml.kernel.org/r/319e4db9-64ae-4bca-92f0-ade85d342ff@google.com
Fixes: 3964acd0db ("mm: mempolicy: fix mbind_range() && vma_adjust() interaction")
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e53ac7374e upstream.
Sometimes the page offlining code can leave behind a hwpoisoned clean
page cache page. This can lead to programs being killed over and over
and over again as they fault in the hwpoisoned page, get killed, and
then get re-spawned by whatever wanted to run them.
This is particularly embarrassing when the page was offlined due to
having too many corrected memory errors. Now we are killing tasks due
to them trying to access memory that probably isn't even corrupted.
This problem can be avoided by invalidating the page from the page fault
handler, which already has a branch for dealing with these kinds of
pages. With this patch we simply pretend the page fault was successful
if the page was invalidated, return to userspace, incur another page
fault, read in the file from disk (to a new memory page), and then
everything works again.
Link: https://lkml.kernel.org/r/20220212213740.423efcea@imladris.surriel.com
Signed-off-by: Rik van Riel <riel@surriel.com>
Reviewed-by: Miaohe Lin <linmiaohe@huawei.com>
Acked-by: Naoya Horiguchi <naoya.horiguchi@nec.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ddbc84f3f5 upstream.
ZONE_MOVABLE uses the remaining memory in each node. Its starting pfn
is also aligned to MAX_ORDER_NR_PAGES. It is possible for the remaining
memory in a node to be less than MAX_ORDER_NR_PAGES, meaning there is
not enough room for ZONE_MOVABLE on that node.
Unfortunately this condition is not checked for. This leads to
zone_movable_pfn[] getting set to a pfn greater than the last pfn in a
node.
calculate_node_totalpages() then sets zone->present_pages to be greater
than zone->spanned_pages which is invalid, as spanned_pages represents
the maximum number of pages in a zone assuming no holes.
Subsequently it is possible free_area_init_core() will observe a zone of
size zero with present pages. In this case it will skip setting up the
zone, including the initialisation of free_lists[].
However populated_zone() checks zone->present_pages to see if a zone has
memory available. This is used by iterators such as
walk_zones_in_node(). pagetypeinfo_showfree() uses this to walk the
free_list of each zone in each node, which are assumed to be initialised
due to the zone not being empty.
As free_area_init_core() never initialised the free_lists[] this results
in the following kernel crash when trying to read /proc/pagetypeinfo:
BUG: kernel NULL pointer dereference, address: 0000000000000000
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC NOPTI
CPU: 0 PID: 456 Comm: cat Not tainted 5.16.0 #461
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-2 04/01/2014
RIP: 0010:pagetypeinfo_show+0x163/0x460
Code: 9e 82 e8 80 57 0e 00 49 8b 06 b9 01 00 00 00 4c 39 f0 75 16 e9 65 02 00 00 48 83 c1 01 48 81 f9 a0 86 01 00 0f 84 48 02 00 00 <48> 8b 00 4c 39 f0 75 e7 48 c7 c2 80 a2 e2 82 48 c7 c6 79 ef e3 82
RSP: 0018:ffffc90001c4bd10 EFLAGS: 00010003
RAX: 0000000000000000 RBX: ffff88801105f638 RCX: 0000000000000001
RDX: 0000000000000001 RSI: 000000000000068b RDI: ffff8880163dc68b
RBP: ffffc90001c4bd90 R08: 0000000000000001 R09: ffff8880163dc67e
R10: 656c6261766f6d6e R11: 6c6261766f6d6e55 R12: ffff88807ffb4a00
R13: ffff88807ffb49f8 R14: ffff88807ffb4580 R15: ffff88807ffb3000
FS: 00007f9c83eff5c0(0000) GS:ffff88807dc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 0000000013c8e000 CR4: 0000000000350ef0
Call Trace:
seq_read_iter+0x128/0x460
proc_reg_read_iter+0x51/0x80
new_sync_read+0x113/0x1a0
vfs_read+0x136/0x1d0
ksys_read+0x70/0xf0
__x64_sys_read+0x1a/0x20
do_syscall_64+0x3b/0xc0
entry_SYSCALL_64_after_hwframe+0x44/0xae
Fix this by checking that the aligned zone_movable_pfn[] does not exceed
the end of the node, and if it does skip creating a movable zone on this
node.
Link: https://lkml.kernel.org/r/20220215025831.2113067-1-apopple@nvidia.com
Fixes: 2a1e274acf ("Create the ZONE_MOVABLE zone")
Signed-off-by: Alistair Popple <apopple@nvidia.com>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Zi Yan <ziy@nvidia.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c7c44ee16 upstream.
When we mount a jffs2 image, assume that the first few blocks of
the image are normal and contain at least one xattr-related inode,
but the next block is abnormal. As a result, an error is returned
in jffs2_scan_eraseblock(). jffs2_clear_xattr_subsystem() is then
called in jffs2_build_filesystem() and then again in
jffs2_do_fill_super().
Finally we can observe the following report:
==================================================================
BUG: KASAN: use-after-free in jffs2_clear_xattr_subsystem+0x95/0x6ac
Read of size 8 at addr ffff8881243384e0 by task mount/719
Call Trace:
dump_stack+0x115/0x16b
jffs2_clear_xattr_subsystem+0x95/0x6ac
jffs2_do_fill_super+0x84f/0xc30
jffs2_fill_super+0x2ea/0x4c0
mtd_get_sb+0x254/0x400
mtd_get_sb_by_nr+0x4f/0xd0
get_tree_mtd+0x498/0x840
jffs2_get_tree+0x25/0x30
vfs_get_tree+0x8d/0x2e0
path_mount+0x50f/0x1e50
do_mount+0x107/0x130
__se_sys_mount+0x1c5/0x2f0
__x64_sys_mount+0xc7/0x160
do_syscall_64+0x45/0x70
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Allocated by task 719:
kasan_save_stack+0x23/0x60
__kasan_kmalloc.constprop.0+0x10b/0x120
kasan_slab_alloc+0x12/0x20
kmem_cache_alloc+0x1c0/0x870
jffs2_alloc_xattr_ref+0x2f/0xa0
jffs2_scan_medium.cold+0x3713/0x4794
jffs2_do_mount_fs.cold+0xa7/0x2253
jffs2_do_fill_super+0x383/0xc30
jffs2_fill_super+0x2ea/0x4c0
[...]
Freed by task 719:
kmem_cache_free+0xcc/0x7b0
jffs2_free_xattr_ref+0x78/0x98
jffs2_clear_xattr_subsystem+0xa1/0x6ac
jffs2_do_mount_fs.cold+0x5e6/0x2253
jffs2_do_fill_super+0x383/0xc30
jffs2_fill_super+0x2ea/0x4c0
[...]
The buggy address belongs to the object at ffff8881243384b8
which belongs to the cache jffs2_xattr_ref of size 48
The buggy address is located 40 bytes inside of
48-byte region [ffff8881243384b8, ffff8881243384e8)
[...]
==================================================================
The triggering of the BUG is shown in the following stack:
-----------------------------------------------------------
jffs2_fill_super
jffs2_do_fill_super
jffs2_do_mount_fs
jffs2_build_filesystem
jffs2_scan_medium
jffs2_scan_eraseblock <--- ERROR
jffs2_clear_xattr_subsystem <--- free
jffs2_clear_xattr_subsystem <--- free again
-----------------------------------------------------------
An error is returned in jffs2_do_mount_fs(). If the error is returned
by jffs2_sum_init(), the jffs2_clear_xattr_subsystem() does not need to
be executed. If the error is returned by jffs2_build_filesystem(), the
jffs2_clear_xattr_subsystem() also does not need to be executed again.
So move jffs2_clear_xattr_subsystem() from 'out_inohash' to 'out_root'
to fix this UAF problem.
Fixes: aa98d7cf59 ("[JFFS2][XATTR] XATTR support on JFFS2 (version. 5)")
Cc: stable@vger.kernel.org
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b5b4f85b0 upstream.
As bughunter reported in bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=215709
f2fs may hang when mounting a fuzzed image, the dmesg shows as below:
__filemap_get_folio+0x3a9/0x590
pagecache_get_page+0x18/0x60
__get_meta_page+0x95/0x460 [f2fs]
get_checkpoint_version+0x2a/0x1e0 [f2fs]
validate_checkpoint+0x8e/0x2a0 [f2fs]
f2fs_get_valid_checkpoint+0xd0/0x620 [f2fs]
f2fs_fill_super+0xc01/0x1d40 [f2fs]
mount_bdev+0x18a/0x1c0
f2fs_mount+0x15/0x20 [f2fs]
legacy_get_tree+0x28/0x50
vfs_get_tree+0x27/0xc0
path_mount+0x480/0xaa0
do_mount+0x7c/0xa0
__x64_sys_mount+0x8b/0xe0
do_syscall_64+0x38/0xc0
entry_SYSCALL_64_after_hwframe+0x44/0xae
The root cause is cp_pack_total_block_count field in checkpoint was fuzzed
to one, as calcuated, two cp pack block locates in the same block address,
so then read latter cp pack block, it will block on the page lock due to
the lock has already held when reading previous cp pack block, fix it by
adding sanity check for cp_pack_total_block_count.
Cc: stable@vger.kernel.org
Signed-off-by: Chao Yu <chao.yu@oppo.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3848e96edf upstream.
xprt_destory() claims XPRT_LOCKED and then calls del_timer_sync().
Both xprt_unlock_connect() and xprt_release() call
->release_xprt()
which drops XPRT_LOCKED and *then* xprt_schedule_autodisconnect()
which calls mod_timer().
This may result in mod_timer() being called *after* del_timer_sync().
When this happens, the timer may fire long after the xprt has been freed,
and run_timer_softirq() will probably crash.
The pairing of ->release_xprt() and xprt_schedule_autodisconnect() is
always called under ->transport_lock. So if we take ->transport_lock to
call del_timer_sync(), we can be sure that mod_timer() will run first
(if it runs at all).
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f97ec5d75e upstream.
Allocating memory with kmalloc and GPF_DMA32 is not allowed, the
allocator will ignore the attribute.
Instead, use dma_alloc_coherent() API as we allocate a small amount of
memory to transfer firmware fragment to the ISH.
On Arcada chromebook, after the patch the warning:
"Unexpected gfp: 0x4 (GFP_DMA32). Fixing up to gfp: 0xcc0 (GFP_KERNEL). Fix your code!"
is gone. The ISH firmware is loaded properly and we can interact with
the ISH:
> ectool --name cros_ish version
...
Build info: arcada_ish_v2.0.3661+3c1a1c1ae0 2022-02-08 05:37:47 @localhost
Tool version: v2.0.12300-900b03ec7f 2022-02-08 10:01:48 @localhost
Fixes: commit 91b228107d ("HID: intel-ish-hid: ISH firmware loader client driver")
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c51abd9683 upstream.
In many cases, keyctl_pkey_params_get_2() is validating the user buffer
lengths against the wrong algorithm properties. Fix it to check against
the correct properties.
Probably this wasn't noticed before because for all asymmetric keys of
the "public_key" subtype, max_data_size == max_sig_size == max_enc_size
== max_dec_size. However, this isn't necessarily true for the
"asym_tpm" subtype (it should be, but it's not strictly validated). Of
course, future key types could have different values as well.
Fixes: 00d60fd3b9 ("KEYS: Provide keyctls to drive the new key type ops for asymmetric keys [ver #2]")
Cc: <stable@vger.kernel.org> # v4.20+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee1fee9005 upstream.
Setting PTRACE_O_SUSPEND_SECCOMP is supposed to be a highly privileged
operation because it allows the tracee to completely bypass all seccomp
filters on kernels with CONFIG_CHECKPOINT_RESTORE=y. It is only supposed to
be settable by a process with global CAP_SYS_ADMIN, and only if that
process is not subject to any seccomp filters at all.
However, while these permission checks were done on the PTRACE_SETOPTIONS
path, they were missing on the PTRACE_SEIZE path, which also sets
user-specified ptrace flags.
Move the permissions checks out into a helper function and let both
ptrace_attach() and ptrace_setoptions() call it.
Cc: stable@kernel.org
Fixes: 13c4a90119 ("seccomp: add ptrace options for suspend/resume")
Signed-off-by: Jann Horn <jannh@google.com>
Link: https://lkml.kernel.org/r/20220319010838.1386861-1-jannh@google.com
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14b457fdde upstream.
When a consumer calls iio_read_channel_processed() and no channel scale
is available, it's assumed that the scale is one and the raw value is
returned as expected.
On the other hand, if the consumer calls iio_convert_raw_to_processed()
the scaling factor requested by the consumer is not applied.
This for example causes the consumer to process mV when expecting uV.
Make sure to always apply the scaling factor requested by the consumer.
Fixes: adc8ec5ff1 ("iio: inkern: pass through raw values if no scaling")
Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220108205319.2046348-3-liambeguin@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1bca97ff95 upstream.
When a consumer calls iio_read_channel_processed() and the channel has
an integer scale, the scale channel scale is applied and the processed
value is returned as expected.
On the other hand, if the consumer calls iio_convert_raw_to_processed()
the scaling factor requested by the consumer is not applied.
This for example causes the consumer to process mV when expecting uV.
Make sure to always apply the scaling factor requested by the consumer.
Fixes: 48e44ce0f8 ("iio:inkern: Add function to read the processed value")
Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220108205319.2046348-2-liambeguin@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea75a342ae upstream.
It's impossible to program a valid value for TRCCONFIGR.QE
when TRCIDR0.QSUPP==0b10. In that case the following is true:
Q element support is implemented, and only supports Q elements without
instruction counts. TRCCONFIGR.QE can only take the values 0b00 or 0b11.
Currently the low bit of QSUPP is checked to see if the low bit of QE can
be written to, but as you can see when QSUPP==0b10 the low bit is cleared
making it impossible to ever write the only valid value of 0b11 to QE.
0b10 would be written instead, which is a reserved QE value even for all
values of QSUPP.
The fix is to allow writing the low bit of QE for any non zero value of
QSUPP.
This change also ensures that the low bit is always set, even when the
user attempts to only set the high bit.
Signed-off-by: James Clark <james.clark@arm.com>
Reviewed-by: Mike Leach <mike.leach@linaro.org>
Fixes: d8c6696208 ("coresight-etm4x: Controls pertaining to the reset, mode, pe and events")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220120113047.2839622-2-james.clark@arm.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05519b8589 upstream.
xhci_decode_ctrl_ctx() returns the untouched buffer as-is if both "drop"
and "add" parameters are zero.
Fix the function to return an empty string in that case.
It was not immediately clear from the possible call chains whether this
issue is currently actually triggerable or not.
Note that before commit 4843b4b5ec ("xhci: fix even more unsafe memory
usage in xhci tracing") the result effect in the failure case was different
as a static buffer was used here, but the code still worked incorrectly.
Fixes: 90d6d5731d ("xhci: Add tracing for input control context")
Cc: stable@vger.kernel.org
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
commit 4843b4b5ec ("xhci: fix even more unsafe memory usage in xhci tracing")
Link: https://lore.kernel.org/r/20220303110903.1662404-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14073ce951 upstream.
xhci_reset() timeout was increased from 250ms to 10 seconds in order to
give Renesas 720201 xHC enough time to get ready in probe.
xhci_reset() is called with interrupts disabled in other places, and
waiting for 10 seconds there is not acceptable.
Add a timeout parameter to xhci_reset(), and adjust it back to 250ms
when called from xhci_stop() or xhci_shutdown() where interrupts are
disabled, and successful reset isn't that critical.
This solves issues when deactivating host mode on platforms like SM8450.
For now don't change the timeout if xHC is reset in xhci_resume().
No issues are reported for it, and we need the reset to succeed.
Locking around that reset needs to be revisited later.
Additionally change the signed integer timeout parameter in
xhci_handshake() to a u64 to match the timeout value we pass to
readl_poll_timeout_atomic()
Fixes: 22ceac1912 ("xhci: Increase reset timeout for Renesas 720201 host.")
Cc: stable@vger.kernel.org
Reported-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reported-by: Pavan Kondeti <quic_pkondeti@quicinc.com>
Tested-by: Pavan Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220303110903.1662404-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70c05e4cf6 upstream.
A race between system resume and device-initiated resume may result in
runtime PM imbalance on USB2 root hub. If a device-initiated resume
starts and system resume xhci_bus_resume() directs U0 before hub driver
sees the resuming device in RESUME state, device-initiated resume will
not be finished in xhci_handle_usb2_port_link_resume(). In this case,
usb_hcd_end_port_resume() call is missing.
This changes calls usb_hcd_end_port_resume() if resuming device reaches
U0 to keep runtime PM balance.
Fixes: a231ec41e6 ("xhci: refactor U0 link state handling in get_port_status")
Cc: stable@vger.kernel.org
Signed-off-by: Henry Lin <henryl@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220303110903.1662404-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3105bc977d upstream.
xhci_decode_usbsts() is expected to return a zero-terminated string by
its only caller, xhci_stop_endpoint_command_watchdog(), which directly
logs the return value:
xhci_warn(xhci, "USBSTS:%s\n", xhci_decode_usbsts(str, usbsts));
However, if no recognized bits are set in usbsts, the function will
return without having called any sprintf() and therefore return an
untouched non-zero-terminated caller-provided buffer, causing garbage
to be output to log.
Fix that by always including the raw value in the output.
Note that before commit 4843b4b5ec ("xhci: fix even more unsafe memory
usage in xhci tracing") the result effect in the failure case was different
as a static buffer was used here, but the code still worked incorrectly.
Fixes: 9c1aa36efd ("xhci: Show host status when watchdog triggers and host is assumed dead.")
Cc: stable@vger.kernel.org
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220303110903.1662404-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1892bf9067 upstream.
The kernel test robot found a problem with the ene_ub6250 subdriver in
usb-storage: It uses structures containing bitfields to represent
hardware bits in its SD_STATUS, MS_STATUS, and SM_STATUS bytes. This
is not safe; it presumes a particular bit ordering and it assumes the
compiler will not insert padding, neither of which is guaranteed.
This patch fixes the problem by changing the structures to simple u8
values, with the bitfields replaced by bitmask constants.
CC: <stable@vger.kernel.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YjOcbuU106UpJ/V8@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e0438f83d upstream.
The following sequence of operations results in a refcount warning:
1. Open device /dev/tpmrm.
2. Remove module tpm_tis_spi.
3. Write a TPM command to the file descriptor opened at step 1.
------------[ cut here ]------------
WARNING: CPU: 3 PID: 1161 at lib/refcount.c:25 kobject_get+0xa0/0xa4
refcount_t: addition on 0; use-after-free.
Modules linked in: tpm_tis_spi tpm_tis_core tpm mdio_bcm_unimac brcmfmac
sha256_generic libsha256 sha256_arm hci_uart btbcm bluetooth cfg80211 vc4
brcmutil ecdh_generic ecc snd_soc_core crc32_arm_ce libaes
raspberrypi_hwmon ac97_bus snd_pcm_dmaengine bcm2711_thermal snd_pcm
snd_timer genet snd phy_generic soundcore [last unloaded: spi_bcm2835]
CPU: 3 PID: 1161 Comm: hold_open Not tainted 5.10.0ls-main-dirty #2
Hardware name: BCM2711
[<c0410c3c>] (unwind_backtrace) from [<c040b580>] (show_stack+0x10/0x14)
[<c040b580>] (show_stack) from [<c1092174>] (dump_stack+0xc4/0xd8)
[<c1092174>] (dump_stack) from [<c0445a30>] (__warn+0x104/0x108)
[<c0445a30>] (__warn) from [<c0445aa8>] (warn_slowpath_fmt+0x74/0xb8)
[<c0445aa8>] (warn_slowpath_fmt) from [<c08435d0>] (kobject_get+0xa0/0xa4)
[<c08435d0>] (kobject_get) from [<bf0a715c>] (tpm_try_get_ops+0x14/0x54 [tpm])
[<bf0a715c>] (tpm_try_get_ops [tpm]) from [<bf0a7d6c>] (tpm_common_write+0x38/0x60 [tpm])
[<bf0a7d6c>] (tpm_common_write [tpm]) from [<c05a7ac0>] (vfs_write+0xc4/0x3c0)
[<c05a7ac0>] (vfs_write) from [<c05a7ee4>] (ksys_write+0x58/0xcc)
[<c05a7ee4>] (ksys_write) from [<c04001a0>] (ret_fast_syscall+0x0/0x4c)
Exception stack(0xc226bfa8 to 0xc226bff0)
bfa0: 00000000 000105b4 00000003 beafe664 00000014 00000000
bfc0: 00000000 000105b4 000103f8 00000004 00000000 00000000 b6f9c000 beafe684
bfe0: 0000006c beafe648 0001056c b6eb6944
---[ end trace d4b8409def9b8b1f ]---
The reason for this warning is the attempt to get the chip->dev reference
in tpm_common_write() although the reference counter is already zero.
Since commit 8979b02aaf ("tpm: Fix reference count to main device") the
extra reference used to prevent a premature zero counter is never taken,
because the required TPM_CHIP_FLAG_TPM2 flag is never set.
Fix this by moving the TPM 2 character device handling from
tpm_chip_alloc() to tpm_add_char_device() which is called at a later point
in time when the flag has been set in case of TPM2.
Commit fdc915f7f7 ("tpm: expose spaces via a device link /dev/tpmrm<n>")
already introduced function tpm_devs_release() to release the extra
reference but did not implement the required put on chip->devs that results
in the call of this function.
Fix this by putting chip->devs in tpm_chip_unregister().
Finally move the new implementation for the TPM 2 handling into a new
function to avoid multiple checks for the TPM_CHIP_FLAG_TPM2 flag in the
good case and error cases.
Cc: stable@vger.kernel.org
Fixes: fdc915f7f7 ("tpm: expose spaces via a device link /dev/tpmrm<n>")
Fixes: 8979b02aaf ("tpm: Fix reference count to main device")
Co-developed-by: Jason Gunthorpe <jgg@ziepe.ca>
Signed-off-by: Jason Gunthorpe <jgg@ziepe.ca>
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b61343b50 upstream.
For various reasons based on the allocator behaviour and typical
use-cases at the time, when the max32_alloc_size optimisation was
introduced it seemed reasonable to couple the reset of the tracked
size to the update of cached32_node upon freeing a relevant IOVA.
However, since subsequent optimisations focused on helping genuine
32-bit devices make best use of even more limited address spaces, it
is now a lot more likely for cached32_node to be anywhere in a "full"
32-bit address space, and as such more likely for space to become
available from IOVAs below that node being freed.
At this point, the short-cut in __cached_rbnode_delete_update() really
doesn't hold up any more, and we need to fix the logic to reliably
provide the expected behaviour. We still want cached32_node to only move
upwards, but we should reset the allocation size if *any* 32-bit space
has become available.
Reported-by: Yunfei Wang <yf.wang@mediatek.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Miles Chen <miles.chen@mediatek.com>
Link: https://lore.kernel.org/r/033815732d83ca73b13c11485ac39336f15c3b40.1646318408.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Cc: Miles Chen <miles.chen@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61cc4534b6 upstream.
It was found that reading /proc/lockdep after a lockdep splat may
potentially cause an access to freed memory if lockdep_unregister_key()
is called after the splat but before access to /proc/lockdep [1]. This
is due to the fact that graph_lock() call in lockdep_unregister_key()
fails after the clearing of debug_locks by the splat process.
After lockdep_unregister_key() is called, the lock_name may be freed
but the corresponding lock_class structure still have a reference to
it. That invalid memory pointer will then be accessed when /proc/lockdep
is read by a user and a use-after-free (UAF) error will be reported if
KASAN is enabled.
To fix this problem, lockdep_unregister_key() is now modified to always
search for a matching key irrespective of the debug_locks state and
zap the corresponding lock class if a matching one is found.
[1] https://lore.kernel.org/lkml/77f05c15-81b6-bddd-9650-80d5f23fe330@i-love.sakura.ne.jp/
Fixes: 8b39adbee8 ("locking/lockdep: Make lockdep_unregister_key() honor 'debug_locks' again")
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Cc: Cheng-Jui Wang <cheng-jui.wang@mediatek.com>
Link: https://lkml.kernel.org/r/20220103023558.1377055-1-longman@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9a564bccb7 ]
Add __GFP_ZERO flag for compose_sadb_supported in function pfkey_register
to initialize the buffer of supp_skb to fix a kernel-info-leak issue.
1) Function pfkey_register calls compose_sadb_supported to request
a sk_buff. 2) compose_sadb_supported calls alloc_sbk to allocate
a sk_buff, but it doesn't zero it. 3) If auth_len is greater 0, then
compose_sadb_supported treats the memory as a struct sadb_supported and
begins to initialize. But it just initializes the field sadb_supported_len
and field sadb_supported_exttype without field sadb_supported_reserved.
Reported-by: TCS Robot <tcs_robot@tencent.com>
Signed-off-by: Haimin Zhang <tcs_kernel@tencent.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e941dc13fd ]
I observed the following problem with the BT404 touch pad
running the Phosh UI:
When e.g. typing on the virtual keyboard pressing "g" would
produce "ggg".
After some analysis it turns out the firmware reports that three
fingers hit that coordinate at the same time, finger 0, 2 and
4 (of the five available 0,1,2,3,4).
DOWN
Zinitix-TS 3-0020: finger 0 down (246, 395)
Zinitix-TS 3-0020: finger 1 up (0, 0)
Zinitix-TS 3-0020: finger 2 down (246, 395)
Zinitix-TS 3-0020: finger 3 up (0, 0)
Zinitix-TS 3-0020: finger 4 down (246, 395)
UP
Zinitix-TS 3-0020: finger 0 up (246, 395)
Zinitix-TS 3-0020: finger 2 up (246, 395)
Zinitix-TS 3-0020: finger 4 up (246, 395)
This is one touch and release: i.e. this is all reported on
touch (down) and release.
There is a field in the struct touch_event called finger_cnt
which is actually a bitmask of the fingers active in the
event.
Rename this field finger_mask as this matches the use contents
better, then use for_each_set_bit() to iterate over just the
fingers that are actally active.
Factor out a finger reporting function zinitix_report_fingers()
to handle all fingers.
Also be more careful in reporting finger down/up: we were
reporting every event with input_mt_report_slot_state(..., true);
but this should only be reported on finger down or move,
not on finger up, so also add code to check p->sub_status
to see what is happening and report correctly.
After this my Zinitix BT404 touchscreen report fingers
flawlessly.
The vendor drive I have notably does not use the "finger_cnt"
and contains obviously incorrect code like this:
if (touch_dev->touch_info.finger_cnt > MAX_SUPPORTED_FINGER_NUM)
touch_dev->touch_info.finger_cnt = MAX_SUPPORTED_FINGER_NUM;
As MAX_SUPPORTED_FINGER_NUM is an ordinal and the field is
a bitmask this seems quite confused.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220228233017.2270599-1-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ebc4cb43ea ]
While computing sgs in spi_map_buf(), the data type
used in min_t() for max_seg_size is 'unsigned int' where
as that of ctlr->max_dma_len is 'size_t'.
min_t(unsigned int,x,y) gives wrong results if one of x/y is
'size_t'
Consider the below examples on a 64-bit machine (ie size_t is
64-bits, and unsigned int is 32-bit).
case 1) min_t(unsigned int, 5, 0x100000001);
case 2) min_t(size_t, 5, 0x100000001);
Case 1 returns '1', where as case 2 returns '5'. As you can see
the result from case 1 is wrong.
This patch fixes the above issue by using the data type of the
parameters that are used in min_t with maximum data length.
Fixes: commit 1a4e53d2fc ("spi: Fix invalid sgs value")
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220316175317.465-1-biju.das.jz@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a760554dc ]
It is not recommened to use platform_get_resource(pdev, IORESOURCE_IRQ)
for requesting IRQ's resources any more, as they can be not ready yet in
case of DT-booting.
platform_get_irq() instead is a recommended way for getting IRQ even if
it was not retrieved earlier.
It also makes code simpler because we're getting "int" value right away
and no conversion from resource to int is required.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi (CGEL ZTE) <chi.minghao@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc328a7d1f ]
Some GPIO lines have stopped working after the patch
commit 2ab73c6d83 ("gpio: Support GPIO controllers without pin-ranges")
And this has supposedly been fixed in the following patches
commit 89ad556b7f ("gpio: Avoid using pin ranges with !PINCTRL")
commit 6dbbf84603 ("gpiolib: Don't free if pin ranges are not defined")
But an erratic behavior where some GPIO lines work while others do not work
has been introduced.
This patch reverts those changes so that the sysfs-gpio interface works
properly again.
Signed-off-by: Marcelo Roberto Jimenez <marcelo.jimenez@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb77bd31c2 ]
When the driver fails to register net device, it should free the DMA
region first, and then do other cleanup.
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30c22f3816 ]
Per VIRTIO v1.1 specification, section 5.1.3.1 Feature bit requirements:
"VIRTIO_NET_F_MQ Requires VIRTIO_NET_F_CTRL_VQ".
There's assumption in the mlx5_vdpa multiqueue code that MQ must come
together with CTRL_VQ. However, there's nowhere in the upper layer to
guarantee this assumption would hold. Were there an untrusted driver
sending down MQ without CTRL_VQ, it would compromise various spots for
e.g. is_index_valid() and is_ctrl_vq_idx(). Although this doesn't end
up with immediate panic or security loophole as of today's code, the
chance for this to be taken advantage of due to future code change is
not zero.
Harden the crispy assumption by failing the set_driver_features() call
when seeing (MQ && !CTRL_VQ). For that end, verify_min_features() is
renamed to verify_driver_features() to reflect the fact that it now does
more than just validate the minimum features. verify_driver_features()
is now used to accommodate various checks against the driver features
for set_driver_features().
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Link: https://lore.kernel.org/r/1642206481-30721-3-git-send-email-si-wei.liu@oracle.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eli Cohen <elic@nvidia.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e7174b9d5 ]
A common pattern for device reset is currently:
vdev->config->reset(vdev);
.. cleanup ..
reset prevents new interrupts from arriving and waits for interrupt
handlers to finish.
However if - as is common - the handler queues a work request which is
flushed during the cleanup stage, we have code adding buffers / trying
to get buffers while device is reset. Not good.
This was reproduced by running
modprobe virtio_console
modprobe -r virtio_console
in a loop.
Fix this up by calling virtio_break_device + flush before reset.
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1786239
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ff2980b6b ]
in tunnel mode, if outer interface(ipv4) is less, it is easily to let
inner IPV6 mtu be less than 1280. If so, a Packet Too Big ICMPV6 message
is received. When send again, packets are fragmentized with 1280, they
are still rejected with ICMPV6(Packet Too Big) by xfrmi_xmit2().
According to RFC4213 Section3.2.2:
if (IPv4 path MTU - 20) is less than 1280
if packet is larger than 1280 bytes
Send ICMPv6 "packet too big" with MTU=1280
Drop packet
else
Encapsulate but do not set the Don't Fragment
flag in the IPv4 header. The resulting IPv4
packet might be fragmented by the IPv4 layer
on the encapsulator or by some router along
the IPv4 path.
endif
else
if packet is larger than (IPv4 path MTU - 20)
Send ICMPv6 "packet too big" with
MTU = (IPv4 path MTU - 20).
Drop packet.
else
Encapsulate and set the Don't Fragment flag
in the IPv4 header.
endif
endif
Packets should be fragmentized with ipv4 outer interface, so change it.
After it is fragemtized with ipv4, there will be double fragmenation.
No.48 & No.51 are ipv6 fragment packets, No.48 is double fragmentized,
then tunneled with IPv4(No.49& No.50), which obey spec. And received peer
cannot decrypt it rightly.
48 2002::10 2002::11 1296(length) IPv6 fragment (off=0 more=y ident=0xa20da5bc nxt=50)
49 0x0000 (0) 2002::10 2002::11 1304 IPv6 fragment (off=0 more=y ident=0x7448042c nxt=44)
50 0x0000 (0) 2002::10 2002::11 200 ESP (SPI=0x00035000)
51 2002::10 2002::11 180 Echo (ping) request
52 0x56dc 2002::10 2002::11 248 IPv6 fragment (off=1232 more=n ident=0xa20da5bc nxt=50)
xfrm6_noneed_fragment has fixed above issues. Finally, it acted like below:
1 0x6206 192.168.1.138 192.168.1.1 1316 Fragmented IP protocol (proto=Encap Security Payload 50, off=0, ID=6206) [Reassembled in #2]
2 0x6206 2002::10 2002::11 88 IPv6 fragment (off=0 more=y ident=0x1f440778 nxt=50)
3 0x0000 2002::10 2002::11 248 ICMPv6 Echo (ping) request
Signed-off-by: Lina Wang <lina.wang@mediatek.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 25666e8ccd ]
As of logitech lightspeed receiver fw version 04.02.B0009,
HIDPP_PARAM_DEVICE_INFO is being reported as 0x11.
With patch "HID: logitech-dj: add support for the new lightspeed receiver
iteration", the mouse starts to error out with:
logitech-djreceiver: unusable device of type UNKNOWN (0x011) connected on
slot 1
and becomes unusable.
This has been noticed on a Logitech G Pro X Superlight fw MPM 25.01.B0018.
Signed-off-by: Lucas Zampieri <lzampier@redhat.com>
Acked-by: Nestor Lopez Casado <nlopezcasad@logitech.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ddbd89deb7 upstream.
The problem I'm addressing was discovered by the LTP test covering
cve-2018-1000204.
A short description of what happens follows:
1) The test case issues a command code 00 (TEST UNIT READY) via the SG_IO
interface with: dxfer_len == 524288, dxdfer_dir == SG_DXFER_FROM_DEV
and a corresponding dxferp. The peculiar thing about this is that TUR
is not reading from the device.
2) In sg_start_req() the invocation of blk_rq_map_user() effectively
bounces the user-space buffer. As if the device was to transfer into
it. Since commit a45b599ad8 ("scsi: sg: allocate with __GFP_ZERO in
sg_build_indirect()") we make sure this first bounce buffer is
allocated with GFP_ZERO.
3) For the rest of the story we keep ignoring that we have a TUR, so the
device won't touch the buffer we prepare as if the we had a
DMA_FROM_DEVICE type of situation. My setup uses a virtio-scsi device
and the buffer allocated by SG is mapped by the function
virtqueue_add_split() which uses DMA_FROM_DEVICE for the "in" sgs (here
scatter-gather and not scsi generics). This mapping involves bouncing
via the swiotlb (we need swiotlb to do virtio in protected guest like
s390 Secure Execution, or AMD SEV).
4) When the SCSI TUR is done, we first copy back the content of the second
(that is swiotlb) bounce buffer (which most likely contains some
previous IO data), to the first bounce buffer, which contains all
zeros. Then we copy back the content of the first bounce buffer to
the user-space buffer.
5) The test case detects that the buffer, which it zero-initialized,
ain't all zeros and fails.
One can argue that this is an swiotlb problem, because without swiotlb
we leak all zeros, and the swiotlb should be transparent in a sense that
it does not affect the outcome (if all other participants are well
behaved).
Copying the content of the original buffer into the swiotlb buffer is
the only way I can think of to make swiotlb transparent in such
scenarios. So let's do just that if in doubt, but allow the driver
to tell us that the whole mapped buffer is going to be overwritten,
in which case we can preserve the old behavior and avoid the performance
impact of the extra bounce.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8926d88ced upstream.
The get_user()/put_user() functions are meant to check for
access_ok(), while the __get_user()/__put_user() functions
don't.
This broke in 4.19 for nds32, when it gained an extraneous
check in __get_user(), but lost the check it needs in
__put_user().
Fixes: 487913ab18 ("nds32: Extract the checking and getting pointer to a macro")
Cc: stable@vger.kernel.org @ v4.19+
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb5abce6b2 upstream.
As part of the series conversion to remove nested TPM operations:
https://lore.kernel.org/all/20190205224723.19671-1-jarkko.sakkinen@linux.intel.com/
exposure of the chip->tpm_mutex was removed from much of the upper
level code. In this conversion, tpm2_del_space() was missed. This
didn't matter much because it's usually called closely after a
converted operation, so there's only a very tiny race window where the
chip can be removed before the space flushing is done which causes a
NULL deref on the mutex. However, there are reports of this window
being hit in practice, so fix this by converting tpm2_del_space() to
use tpm_try_get_ops(), which performs all the teardown checks before
acquring the mutex.
Cc: stable@vger.kernel.org # 5.4.x
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a2d4496e1 upstream.
While commit 6a01afcf84 ("mac80211: mesh: Free ie data when leaving
mesh") fixed a memory leak on mesh leave / teardown it introduced a
potential memory corruption caused by a double free when rejoining the
mesh:
ieee80211_leave_mesh()
-> kfree(sdata->u.mesh.ie);
...
ieee80211_join_mesh()
-> copy_mesh_setup()
-> old_ie = ifmsh->ie;
-> kfree(old_ie);
This double free / kernel panics can be reproduced by using wpa_supplicant
with an encrypted mesh (if set up without encryption via "iw" then
ifmsh->ie is always NULL, which avoids this issue). And then calling:
$ iw dev mesh0 mesh leave
$ iw dev mesh0 mesh join my-mesh
Note that typically these commands are not used / working when using
wpa_supplicant. And it seems that wpa_supplicant or wpa_cli are going
through a NETDEV_DOWN/NETDEV_UP cycle between a mesh leave and mesh join
where the NETDEV_UP resets the mesh.ie to NULL via a memcpy of
default_mesh_setup in cfg80211_netdev_notifier_call, which then avoids
the memory corruption, too.
The issue was first observed in an application which was not using
wpa_supplicant but "Senf" instead, which implements its own calls to
nl80211.
Fixing the issue by removing the kfree()'ing of the mesh IE in the mesh
join function and leaving it solely up to the mesh leave to free the
mesh IE.
Cc: stable@vger.kernel.org
Fixes: 6a01afcf84 ("mac80211: mesh: Free ie data when leaving mesh")
Reported-by: Matthias Kretschmer <mathias.kretschmer@fit.fraunhofer.de>
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Tested-by: Mathias Kretschmer <mathias.kretschmer@fit.fraunhofer.de>
Link: https://lore.kernel.org/r/20220310183513.28589-1-linus.luessing@c0d3.blue
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10c5357874 upstream.
Currently rcu_preempt_deferred_qs_irqrestore() releases rnp->boost_mtx
before reporting the expedited quiescent state. Under heavy real-time
load, this can result in this function being preempted before the
quiescent state is reported, which can in turn prevent the expedited grace
period from completing. Tim Murray reports that the resulting expedited
grace periods can take hundreds of milliseconds and even more than one
second, when they should normally complete in less than a millisecond.
This was fine given that there were no particular response-time
constraints for synchronize_rcu_expedited(), as it was designed
for throughput rather than latency. However, some users now need
sub-100-millisecond response-time constratints.
This patch therefore follows Neeraj's suggestion (seconded by Tim and
by Uladzislau Rezki) of simply reversing the two operations.
Reported-by: Tim Murray <timmurray@google.com>
Reported-by: Joel Fernandes <joelaf@google.com>
Reported-by: Neeraj Upadhyay <quic_neeraju@quicinc.com>
Reviewed-by: Neeraj Upadhyay <quic_neeraju@quicinc.com>
Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
Tested-by: Tim Murray <timmurray@google.com>
Cc: Todd Kjos <tkjos@google.com>
Cc: Sandeep Patil <sspatil@google.com>
Cc: <stable@vger.kernel.org> # 5.4.x
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8893d27ffc upstream.
The implementations of aead and skcipher in the QAT driver do not
support properly requests with the CRYPTO_TFM_REQ_MAY_BACKLOG flag set.
If the HW queue is full, the driver returns -EBUSY but does not enqueue
the request.
This can result in applications like dm-crypt waiting indefinitely for a
completion of a request that was never submitted to the hardware.
To avoid this problem, disable the registration of all crypto algorithms
in the QAT driver by setting the number of crypto instances to 0 at
configuration time.
Cc: stable@vger.kernel.org
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c844d22fe0 upstream.
Clevo NL5xRU and NL5xNU/TUXEDO Aura 15 Gen1 and Gen2 have both a working
native and video interface. However the default detection mechanism first
registers the video interface before unregistering it again and switching
to the native interface during boot. This results in a dangling SBIOS
request for backlight change for some reason, causing the backlight to
switch to ~2% once per boot on the first power cord connect or disconnect
event. Setting the native interface explicitly circumvents this buggy
behaviour by avoiding the unregistering process.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7dacee0b9e upstream.
For some reason, the Microsoft Surface Go 3 uses the standard ACPI
interface for battery information, but does not use the standard PNP0C0A
HID. Instead it uses MSHW0146 as identifier. Add that ID to the driver
as this seems to work well.
Additionally, the power state is not updated immediately after the AC
has been (un-)plugged, so add the respective quirk for that.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e702196bf8 upstream.
On this board the ACPI RSDP structure points to both a RSDT and an XSDT,
but the XSDT points to a truncated FADT. This causes all sorts of trouble
and usually a complete failure to boot after the following error occurs:
ACPI Error: Unsupported address space: 0x20 (*/hwregs-*)
ACPI Error: AE_SUPPORT, Unable to initialize fixed events (*/evevent-*)
ACPI: Unable to start ACPI Interpreter
This leaves the ACPI implementation in such a broken state that subsequent
kernel subsystem initialisations go wrong, resulting in among others
mismapped PCI memory, SATA and USB enumeration failures, and freezes.
As this is an older embedded platform that will likely never see any BIOS
updates to address this issue and its default shipping OS only complies to
ACPI 1.0, work around this by forcing `acpi=rsdt`. This patch, applied on
top of Linux 5.10.102, was confirmed on real hardware to fix the issue.
Signed-off-by: Mark Cilissen <mark@yotsuba.nl>
Cc: All applicable <stable@vger.kernel.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9e6faeafa upstream.
All packets on ingress (except for jumbo) are terminated with a 4-bytes
CRC checksum. It's the responsability of the driver to strip those 4
bytes. Unfortunately a change dating back to March 2017 re-shuffled some
code and made the CRC stripping code effectively dead.
This change re-orders that part a bit such that the datalen is
immediately altered if needed.
Fixes: 4902a92270 ("drivers: net: xgene: Add workaround for errata 10GE_8/ENET_11")
Cc: stable@vger.kernel.org
Signed-off-by: Stephane Graber <stgraber@ubuntu.com>
Tested-by: Stephane Graber <stgraber@ubuntu.com>
Link: https://lore.kernel.org/r/20220322224205.752795-1-stgraber@ubuntu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 17aaf01933 upstream.
Tests 72 and 78 for ALSA in kselftest fail due to reading
inconsistent values from some devices on a VirtualBox
Virtual Machine using the snd_intel8x0 driver for the AC'97
Audio Controller device.
Taking for example test number 72, this is what the test reports:
"Surround Playback Volume.0 expected 1 but read 0, is_volatile 0"
"Surround Playback Volume.1 expected 0 but read 1, is_volatile 0"
These errors repeat for each value from 0 to 31.
Taking a look at these error messages it is possible to notice
that the written values are read back swapped.
When the write is performed, these values are initially stored in
an array used to sanity-check them and write them in the pcmreg
array. To write them, the two one-byte values are packed together
in a two-byte variable through bitwise operations: the first
value is shifted left by one byte and the second value is stored in the
right byte through a bitwise OR. When reading the values back,
right shifts are performed to retrieve the previously stored
bytes. These shifts are executed in the wrong order, thus
reporting the values swapped as shown above.
This patch fixes this mistake by reversing the read
operations' order.
Signed-off-by: Giacomo Guiduzzi <guiduzzi.giacomo@gmail.com>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220322200653.15862-1-guiduzzi.giacomo@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c3201f8c7 upstream.
Like the previous fixes to hw_params and hw_free ioctl races, we need
to paper over the concurrent prepare ioctl calls against hw_params and
hw_free, too.
This patch implements the locking with the existing
runtime->buffer_mutex for prepare ioctls. Unlike the previous case
for snd_pcm_hw_hw_params() and snd_pcm_hw_free(), snd_pcm_prepare() is
performed to the linked streams, hence the lock can't be applied
simply on the top. For tracking the lock in each linked substream, we
modify snd_pcm_action_group() slightly and apply the buffer_mutex for
the case stream_lock=false (formerly there was no lock applied)
there.
Cc: <stable@vger.kernel.org>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20220322170720.3529-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dca947d4d2 upstream.
In the current PCM design, the read/write syscalls (as well as the
equivalent ioctls) are allowed before the PCM stream is running, that
is, at PCM PREPARED state. Meanwhile, we also allow to re-issue
hw_params and hw_free ioctl calls at the PREPARED state that may
change or free the buffers, too. The problem is that there is no
protection against those mix-ups.
This patch applies the previously introduced runtime->buffer_mutex to
the read/write operations so that the concurrent hw_params or hw_free
call can no longer interfere during the operation. The mutex is
unlocked before scheduling, so we don't take it too long.
Cc: <stable@vger.kernel.org>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20220322170720.3529-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92ee3c60ec upstream.
Currently we have neither proper check nor protection against the
concurrent calls of PCM hw_params and hw_free ioctls, which may result
in a UAF. Since the existing PCM stream lock can't be used for
protecting the whole ioctl operations, we need a new mutex to protect
those racy calls.
This patch introduced a new mutex, runtime->buffer_mutex, and applies
it to both hw_params and hw_free ioctl code paths. Along with it, the
both functions are slightly modified (the mmap_count check is moved
into the state-check block) for code simplicity.
Reported-by: Hu Jiahui <kirin.say@gmail.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20220322170720.3529-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd94df1795 upstream.
New device id for Corsair Virtuoso SE RGB Wireless that currently is not
in the mixer_map. This entry in the mixer_map is necessary in order to
label its mixer appropriately and allow userspace to pick the correct
volume controls. For instance, my own Corsair Virtuoso SE RGB Wireless
headset has this new ID and consequently, the sidetone and volume are not
working correctly without this change.
> sudo lsusb -v | grep -i corsair
Bus 007 Device 011: ID 1b1c:0a40 Corsair CORSAIR VIRTUOSO SE Wireless Gam
idVendor 0x1b1c Corsair
iManufacturer 1 Corsair
iProduct 2 CORSAIR VIRTUOSO SE Wireless Gaming Headset
Signed-off-by: Reza Jahanbakhshi <reza.jahanbakhshi@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220304212303.195949-1-reza.jahanbakhshi@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit efb6402c3c upstream.
We've got syzbot reports hitting INT_MAX overflow at vmalloc()
allocation that is called from snd_pcm_plug_alloc(). Although we
apply the restrictions to input parameters, it's based only on the
hw_params of the underlying PCM device. Since the PCM OSS layer
allocates a temporary buffer for the data conversion, the size may
become unexpectedly large when more channels or higher rates is given;
in the reported case, it went over INT_MAX, hence it hits WARN_ON().
This patch is an attempt to avoid such an overflow and an allocation
for too large buffers. First off, it adds the limit of 1MB as the
upper bound for period bytes. This must be large enough for all use
cases, and we really don't want to handle a larger temporary buffer
than this size. The size check is performed at two places, where the
original period bytes is calculated and where the plugin buffer size
is calculated.
In addition, the driver uses array_size() and array3_size() for
multiplications to catch overflows for the converted period size and
buffer bytes.
Reported-by: syzbot+72732c532ac1454eeee9@syzkaller.appspotmail.com
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/00000000000085b1b305da5a66f3@google.com
Link: https://lore.kernel.org/r/20220318082036.29699-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e8e4c8f66 upstream.
When an invalid (non existing) handle is used in a TPM command,
that uses the resource manager interface (/dev/tpmrm0) the resource
manager tries to load it from its internal cache, but fails and
the tpm_dev_transmit returns an -EINVAL error to the caller.
The existing async handler doesn't handle these error cases
currently and the condition in the poll handler never returns
mask with EPOLLIN set.
The result is that the poll call blocks and the application gets stuck
until the user_read_timer wakes it up after 120 sec.
Change the tpm_dev_async_work function to handle error conditions
returned from tpm_dev_transmit they are also reflected in the poll mask
and a correct error code could passed back to the caller.
Cc: Jarkko Sakkinen <jarkko@kernel.org>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: <linux-integrity@vger.kernel.org>
Cc: <stable@vger.kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Fixes: 9e1b74a63f ("tpm: add support for nonblocking operation")
Tested-by: Jarkko Sakkinen<jarkko@kernel.org>
Signed-off-by: Tadeusz Struk <tstruk@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Cc: Tadeusz Struk <tadeusz.struk@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e574576416 upstream.
cgroup process migration permission checks are performed at write time as
whether a given operation is allowed or not is dependent on the content of
the write - the PID. This currently uses current's cgroup namespace which is
a potential security weakness as it may allow scenarios where a less
privileged process tricks a more privileged one into writing into a fd that
it created.
This patch makes cgroup remember the cgroup namespace at the time of open
and uses it for migration permission checks instad of current's. Note that
this only applies to cgroup2 as cgroup1 doesn't have namespace support.
This also fixes a use-after-free bug on cgroupns reported in
https://lore.kernel.org/r/00000000000048c15c05d0083397@google.com
Note that backporting this fix also requires the preceding patch.
Reported-by: "Eric W. Biederman" <ebiederm@xmission.com>
Suggested-by: Linus Torvalds <torvalds@linuxfoundation.org>
Cc: Michal Koutný <mkoutny@suse.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Michal Koutný <mkoutny@suse.com>
Reported-by: syzbot+50f5cf33a284ce738b62@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/00000000000048c15c05d0083397@google.com
Fixes: 5136f6365c ("cgroup: implement "nsdelegate" mount option")
Signed-off-by: Tejun Heo <tj@kernel.org>
[mkoutny: v5.10: duplicate ns check in procs/threads write handler, adjust context]
Signed-off-by: Michal Koutný <mkoutny@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d2b5955b3 upstream.
of->priv is currently used by each interface file implementation to store
private information. This patch collects the current two private data usages
into struct cgroup_file_ctx which is allocated and freed by the common path.
This allows generic private data which applies to multiple files, which will
be used to in the following patch.
Note that cgroup_procs iterator is now embedded as procs.iter in the new
cgroup_file_ctx so that it doesn't need to be allocated and freed
separately.
v2: union dropped from cgroup_file_ctx and the procs iterator is embedded in
cgroup_file_ctx as suggested by Linus.
v3: Michal pointed out that cgroup1's procs pidlist uses of->priv too.
Converted. Didn't change to embedded allocation as cgroup1 pidlists get
stored for caching.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Reviewed-by: Michal Koutný <mkoutny@suse.com>
[mkoutny: v5.10: modify cgroup.pressure handlers, adjust context]
Signed-off-by: Michal Koutný <mkoutny@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 839a534f1e upstream.
In d_make_root, when we fail to allocate dentry for root inode,
we will iput root inode and returned value is NULL in this function.
So we do not need to release this inode again at d_make_root's caller.
Signed-off-by: Chen Li <chenli@uniontech.com>
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Cc: Tadeusz Struk <tadeusz.struk@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ebe48d368e upstream.
The maximum message size that can be send is bigger than
the maximum site that skb_page_frag_refill can allocate.
So it is possible to write beyond the allocated buffer.
Fix this by doing a fallback to COW in that case.
v2:
Avoid get get_order() costs as suggested by Linus Torvalds.
Fixes: cac2661c53 ("esp4: Avoid skb_cow_data whenever possible")
Fixes: 03e2a30f6a ("esp6: Avoid skb_cow_data whenever possible")
Reported-by: valis <sec@valis.email>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c70c453abc upstream.
According to Documentation/driver-api/usb/URB.rst when a device
is unplugged usb_submit_urb() returns -ENODEV.
This error code propagates all the way up to usbnet_read_cmd() and
usbnet_write_cmd() calls inside the smsc95xx.c driver during
Ethernet cable unplug, unbind or reboot.
This causes the following errors to be shown on reboot, for example:
ci_hdrc ci_hdrc.1: remove, state 1
usb usb2: USB disconnect, device number 1
usb 2-1: USB disconnect, device number 2
usb 2-1.1: USB disconnect, device number 3
smsc95xx 2-1.1:1.0 eth1: unregister 'smsc95xx' usb-ci_hdrc.1-1.1, smsc95xx USB 2.0 Ethernet
smsc95xx 2-1.1:1.0 eth1: Failed to read reg index 0x00000114: -19
smsc95xx 2-1.1:1.0 eth1: Error reading MII_ACCESS
smsc95xx 2-1.1:1.0 eth1: __smsc95xx_mdio_read: MII is busy
smsc95xx 2-1.1:1.0 eth1: Failed to read reg index 0x00000114: -19
smsc95xx 2-1.1:1.0 eth1: Error reading MII_ACCESS
smsc95xx 2-1.1:1.0 eth1: __smsc95xx_mdio_read: MII is busy
smsc95xx 2-1.1:1.0 eth1: hardware isn't capable of remote wakeup
usb 2-1.4: USB disconnect, device number 4
ci_hdrc ci_hdrc.1: USB bus 2 deregistered
ci_hdrc ci_hdrc.0: remove, state 4
usb usb1: USB disconnect, device number 1
ci_hdrc ci_hdrc.0: USB bus 1 deregistered
imx2-wdt 30280000.watchdog: Device shutdown: Expect reboot!
reboot: Restarting system
Ignore the -ENODEV errors inside __smsc95xx_mdio_read() and
__smsc95xx_phy_wait_not_busy() and do not print error messages
when -ENODEV is returned.
Fixes: a049a30fc2 ("net: usb: Correct PHY handling of smsc95xx")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3cf6a32f3f upstream.
Before this patch, the symbol end address fixup to be called, needed two
conditions being met:
if (prev->end == prev->start && prev->end != curr->start)
Where
"prev->end == prev->start" means that prev is zero-long
(and thus needs a fixup)
and
"prev->end != curr->start" means that fixup hasn't been applied yet
However, this logic is incorrect in the following situation:
*curr = {rb_node = {__rb_parent_color = 278218928,
rb_right = 0x0, rb_left = 0x0},
start = 0xc000000000062354,
end = 0xc000000000062354, namelen = 40, type = 2 '\002',
binding = 0 '\000', idle = 0 '\000', ignore = 0 '\000',
inlined = 0 '\000', arch_sym = 0 '\000', annotate2 = false,
name = 0x1159739e "kprobe_optinsn_page\t[__builtin__kprobes]"}
*prev = {rb_node = {__rb_parent_color = 278219041,
rb_right = 0x109548b0, rb_left = 0x109547c0},
start = 0xc000000000062354,
end = 0xc000000000062354, namelen = 12, type = 2 '\002',
binding = 1 '\001', idle = 0 '\000', ignore = 0 '\000',
inlined = 0 '\000', arch_sym = 0 '\000', annotate2 = false,
name = 0x1095486e "optinsn_slot"}
In this case, prev->start == prev->end == curr->start == curr->end,
thus the condition above thinks that "we need a fixup due to zero
length of prev symbol, but it has been probably done, since the
prev->end == curr->start", which is wrong.
After the patch, the execution path proceeds to arch__symbols__fixup_end
function which fixes up the size of prev symbol by adding page_size to
its end offset.
Fixes: 3b01a413c1 ("perf symbols: Improve kallsyms symbol end addr calculation")
Signed-off-by: Michael Petlan <mpetlan@redhat.com>
Cc: Athira Jajeev <atrajeev@linux.vnet.ibm.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: http://lore.kernel.org/lkml/20220317135536.805-1-mpetlan@redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5600f69866 upstream.
Syzbot reported warning in usb_submit_urb() which is caused by wrong
endpoint type. There was a check for the number of endpoints, but not
for the type of endpoint.
Fix it by replacing old desc.bNumEndpoints check with
usb_find_common_endpoints() helper for finding endpoints
Fail log:
usb 5-1: BOGUS urb xfer, pipe 1 != type 3
WARNING: CPU: 2 PID: 48 at drivers/usb/core/urb.c:502 usb_submit_urb+0xed2/0x18a0 drivers/usb/core/urb.c:502
Modules linked in:
CPU: 2 PID: 48 Comm: kworker/2:2 Not tainted 5.17.0-rc6-syzkaller-00226-g07ebd38a0da2 #0
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-2 04/01/2014
Workqueue: usb_hub_wq hub_event
...
Call Trace:
<TASK>
aiptek_open+0xd5/0x130 drivers/input/tablet/aiptek.c:830
input_open_device+0x1bb/0x320 drivers/input/input.c:629
kbd_connect+0xfe/0x160 drivers/tty/vt/keyboard.c:1593
Fixes: 8e20cf2bce ("Input: aiptek - fix crash on detecting device without endpoints")
Reported-and-tested-by: syzbot+75cccf2b7da87fb6f84b@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/20220308194328.26220-1-paskripkin@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9b667a82c upstream.
The syzbot fuzzer reported a minor bug in the usbtmc driver:
usb 5-1: BOGUS control dir, pipe 80001e80 doesn't match bRequestType 0
WARNING: CPU: 0 PID: 3813 at drivers/usb/core/urb.c:412
usb_submit_urb+0x13a5/0x1970 drivers/usb/core/urb.c:410
Modules linked in:
CPU: 0 PID: 3813 Comm: syz-executor122 Not tainted
5.17.0-rc5-syzkaller-00306-g2293be58d6a1 #0
...
Call Trace:
<TASK>
usb_start_wait_urb+0x113/0x530 drivers/usb/core/message.c:58
usb_internal_control_msg drivers/usb/core/message.c:102 [inline]
usb_control_msg+0x2a5/0x4b0 drivers/usb/core/message.c:153
usbtmc_ioctl_request drivers/usb/class/usbtmc.c:1947 [inline]
The problem is that usbtmc_ioctl_request() uses usb_rcvctrlpipe() for
all of its transfers, whether they are in or out. It's easy to fix.
CC: <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+a48e3d1a875240cab5de@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YiEsYTPEE6lOCOA5@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 16b1941eac upstream.
The syzbot fuzzer found a use-after-free bug:
BUG: KASAN: use-after-free in dev_uevent+0x712/0x780 drivers/base/core.c:2320
Read of size 8 at addr ffff88802b934098 by task udevd/3689
CPU: 2 PID: 3689 Comm: udevd Not tainted 5.17.0-rc4-syzkaller-00229-g4f12b742eb2b #0
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-2 04/01/2014
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_address_description.constprop.0.cold+0x8d/0x303 mm/kasan/report.c:255
__kasan_report mm/kasan/report.c:442 [inline]
kasan_report.cold+0x83/0xdf mm/kasan/report.c:459
dev_uevent+0x712/0x780 drivers/base/core.c:2320
uevent_show+0x1b8/0x380 drivers/base/core.c:2391
dev_attr_show+0x4b/0x90 drivers/base/core.c:2094
Although the bug manifested in the driver core, the real cause was a
race with the gadget core. dev_uevent() does:
if (dev->driver)
add_uevent_var(env, "DRIVER=%s", dev->driver->name);
and between the test and the dereference of dev->driver, the gadget
core sets dev->driver to NULL.
The race wouldn't occur if the gadget core registered its devices on
a real bus, using the standard synchronization techniques of the
driver core. However, it's not necessary to make such a large change
in order to fix this bug; all we need to do is make sure that
udc->dev.driver is always NULL.
In fact, there is no reason for udc->dev.driver ever to be set to
anything, let alone to the value it currently gets: the address of the
gadget's driver. After all, a gadget driver only knows how to manage
a gadget, not how to manage a UDC.
This patch simply removes the statements in the gadget core that touch
udc->dev.driver.
Fixes: 2ccea03a8f ("usb: gadget: introduce UDC Class")
CC: <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+348b571beb5eeb70a582@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YiQgukfFFbBnwJ/9@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7f34b43e07 ]
The newly introduced TRAMP_VALIAS definition causes a build warning
with clang-14:
arch/arm64/include/asm/vectors.h:66:31: error: arithmetic on a null pointer treated as a cast from integer to pointer is a GNU extension [-Werror,-Wnull-pointer-arithmetic]
return (char *)TRAMP_VALIAS + SZ_2K * slot;
Change the addition to something clang does not complain about.
Fixes: bd09128d16 ("arm64: Add percpu vectors for EL1")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: James Morse <james.morse@arm.com>
Link: https://lore.kernel.org/r/20220316183833.1563139-1-arnd@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e0341aefc ]
ACL rules can be offloaded to VCAP IS2 either through chain 0, or, since
the blamed commit, through a chain index whose number encodes a specific
PAG (Policy Action Group) and lookup number.
The chain number is translated through ocelot_chain_to_pag() into a PAG,
and through ocelot_chain_to_lookup() into a lookup number.
The problem with the blamed commit is that the above 2 functions don't
have special treatment for chain 0. So ocelot_chain_to_pag(0) returns
filter->pag = 224, which is in fact -32, but the "pag" field is an u8.
So we end up programming the hardware with VCAP IS2 entries having a PAG
of 224. But the way in which the PAG works is that it defines a subset
of VCAP IS2 filters which should match on a packet. The default PAG is
0, and previous VCAP IS1 rules (which we offload using 'goto') can
modify it. So basically, we are installing filters with a PAG on which
no packet will ever match. This is the hardware equivalent of adding
filters to a chain which has no 'goto' to it.
Restore the previous functionality by making ACL filters offloaded to
chain 0 go to PAG 0 and lookup number 0. The choice of PAG is clearly
correct, but the choice of lookup number isn't "as before" (which was to
leave the lookup a "don't care"). However, lookup 0 should be fine,
since even though there are ACL actions (policers) which have a
requirement to be used in a specific lookup, that lookup is 0.
Fixes: 226e9cd82a ("net: mscc: ocelot: only install TCAM entries into a specific lookup and PAG")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220316192117.2568261-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f643c88c8 ]
The RXCHK block will return a partial checksum of 0 if it encounters
a problem while receiving a packet. Since a 1's complement sum can
only produce this result if no bits are set in the received data
stream it is fair to treat it as an invalid partial checksum and
not pass it up the stack.
Fixes: 8101553978 ("net: bcmgenet: use CHECKSUM_COMPLETE for NETIF_F_RXCSUM")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220317012812.1313196-1-opendmb@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 424e7834e2 ]
Commit b7a49f7305 ("bnx2x: Utilize firmware 7.13.21.0")
added request_firmware() logic in probe() which caused
load failure when firmware file is not present in initrd (below),
as access to firmware file is not feasible during probe.
Direct firmware load for bnx2x/bnx2x-e2-7.13.15.0.fw failed with error -2
Direct firmware load for bnx2x/bnx2x-e2-7.13.21.0.fw failed with error -2
This patch fixes this issue by -
1. Removing request_firmware() logic from the probe()
such that .ndo_open() handle it as it used to handle
it earlier
2. Given request_firmware() is removed from probe(), so
driver has to relax FW version comparisons a bit against
the already loaded FW version (by some other PFs of same
adapter) to allow different compatible/close enough FWs with which
multiple PFs may run with (in different environments), as the
given PF who is in probe flow has no idea now with which firmware
file version it is going to initialize the device in ndo_open()
Link: https://lore.kernel.org/all/46f2d9d9-ae7f-b332-ddeb-b59802be2bab@molgen.mpg.de/
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Fixes: b7a49f7305 ("bnx2x: Utilize firmware 7.13.21.0")
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Link: https://lore.kernel.org/r/20220316214613.6884-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f74b29a4f ]
As the potential failure of the dma_map_single(),
it should be better to check it and return error
if fails.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 837d9e4940 ]
This bug resulted in only the current mode being resumed and suspended when
the PHY supported both fiber and copper modes and when the PHY only supported
copper mode the fiber mode would incorrectly be attempted to be resumed and
suspended.
Fixes: 3758be3dc1 ("Marvell phy: add functions to suspend and resume both interfaces: fiber and copper links.")
Signed-off-by: Kurt Cancemi <kurt@x64architecture.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220312201512.326047-1-kurt@x64architecture.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4db4075f92 ]
Commit 5f9c55c806 ("ipv6: check return value of ipv6_skip_exthdr")
introduced an incorrect check, which leads to all ESP packets over
either TCPv6 or UDPv6 encapsulation being dropped. In this particular
case, offset is negative, since skb->data points to the ESP header in
the following chain of headers, while skb->network_header points to
the IPv6 header:
IPv6 | ext | ... | ext | UDP | ESP | ...
That doesn't seem to be a problem, especially considering that if we
reach esp6_input_done2, we're guaranteed to have a full set of headers
available (otherwise the packet would have been dropped earlier in the
stack). However, it means that the return value will (intentionally)
be negative. We can make the test more specific, as the expected
return value of ipv6_skip_exthdr will be the (negated) size of either
a UDP header, or a TCP header with possible options.
In the future, we should probably either make ipv6_skip_exthdr
explicitly accept negative offsets (and adjust its return value for
error cases), or make ipv6_skip_exthdr only take non-negative
offsets (and audit all callers).
Fixes: 5f9c55c806 ("ipv6: check return value of ipv6_skip_exthdr")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e6ed96376 ]
When iterating over sockets using vsock_for_each_connected_socket, make
sure that a transport filters out sockets that don't belong to the
transport.
There actually was an issue caused by this; in a nested VM
configuration, destroying the nested VM (which often involves the
closing of /dev/vhost-vsock if there was h2g connections to the nested
VM) kills not only the h2g connections, but also all existing g2h
connections to the (outmost) host which are totally unrelated.
Tested: Executed the following steps on Cuttlefish (Android running on a
VM) [1]: (1) Enter into an `adb shell` session - to have a g2h
connection inside the VM, (2) open and then close /dev/vhost-vsock by
`exec 3< /dev/vhost-vsock && exec 3<&-`, (3) observe that the adb
session is not reset.
[1] https://android.googlesource.com/device/google/cuttlefish/
Fixes: c0cfa2d8a7 ("vsock: add multi-transports support")
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jiyong Park <jiyong@google.com>
Link: https://lore.kernel.org/r/20220311020017.1509316-1-jiyong@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9feaf8b387 ]
When "dump_apple_properties" is used on the kernel boot command line,
it causes an Unknown parameter message and the string is added to init's
argument strings:
Unknown kernel command line parameters "dump_apple_properties
BOOT_IMAGE=/boot/bzImage-517rc6 efivar_ssdt=newcpu_ssdt", will be
passed to user space.
Run /sbin/init as init process
with arguments:
/sbin/init
dump_apple_properties
with environment:
HOME=/
TERM=linux
BOOT_IMAGE=/boot/bzImage-517rc6
efivar_ssdt=newcpu_ssdt
Similarly when "efivar_ssdt=somestring" is used, it is added to the
Unknown parameter message and to init's environment strings, polluting
them (see examples above).
Change the return value of the __setup functions to 1 to indicate
that the __setup options have been handled.
Fixes: 58c5475aba ("x86/efi: Retrieve and assign Apple device properties")
Fixes: 475fb4e8b2 ("efi / ACPI: load SSTDs from EFI variables")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru>
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: linux-efi@vger.kernel.org
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Octavian Purdila <octavian.purdila@intel.com>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Link: https://lore.kernel.org/r/20220301041851.12459-1-rdunlap@infradead.org
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 029c4628b2 upstream.
In our testing, a livelock task was found. Through sysrq printing, same
stack was found every time, as follows:
__swap_duplicate+0x58/0x1a0
swapcache_prepare+0x24/0x30
__read_swap_cache_async+0xac/0x220
read_swap_cache_async+0x58/0xa0
swapin_readahead+0x24c/0x628
do_swap_page+0x374/0x8a0
__handle_mm_fault+0x598/0xd60
handle_mm_fault+0x114/0x200
do_page_fault+0x148/0x4d0
do_translation_fault+0xb0/0xd4
do_mem_abort+0x50/0xb0
The reason for the livelock is that swapcache_prepare() always returns
EEXIST, indicating that SWAP_HAS_CACHE has not been cleared, so that it
cannot jump out of the loop. We suspect that the task that clears the
SWAP_HAS_CACHE flag never gets a chance to run. We try to lower the
priority of the task stuck in a livelock so that the task that clears
the SWAP_HAS_CACHE flag will run. The results show that the system
returns to normal after the priority is lowered.
In our testing, multiple real-time tasks are bound to the same core, and
the task in the livelock is the highest priority task of the core, so
the livelocked task cannot be preempted.
Although cond_resched() is used by __read_swap_cache_async, it is an
empty function in the preemptive system and cannot achieve the purpose
of releasing the CPU. A high-priority task cannot release the CPU
unless preempted by a higher-priority task. But when this task is
already the highest priority task on this core, other tasks will not be
able to be scheduled. So we think we should replace cond_resched() with
schedule_timeout_uninterruptible(1), schedule_timeout_interruptible will
call set_current_state first to set the task state, so the task will be
removed from the running queue, so as to achieve the purpose of giving
up the CPU and prevent it from running in kernel mode for too long.
(akpm: ugly hack becomes uglier. But it fixes the issue in a
backportable-to-stable fashion while we hopefully work on something
better)
Link: https://lkml.kernel.org/r/20220221111749.1928222-1-cgel.zte@gmail.com
Signed-off-by: Guo Ziliang <guo.ziliang@zte.com.cn>
Reported-by: Zeal Robot <zealci@zte.com.cn>
Reviewed-by: Ran Xiaokai <ran.xiaokai@zte.com.cn>
Reviewed-by: Jiang Xuexin <jiang.xuexin@zte.com.cn>
Reviewed-by: Yang Yang <yang.yang29@zte.com.cn>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Roger Quadros <rogerq@kernel.org>
Cc: Ziliang Guo <guo.ziliang@zte.com.cn>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a680b1832c upstream.
The generate function in struct rng_alg expects that the destination
buffer is completely filled if the function returns 0. qcom_rng_read()
can run into a situation where the buffer is partially filled with
randomness and the remaining part of the buffer is zeroed since
qcom_rng_generate() doesn't check the return value. This issue can
be reproduced by running the following from libkcapi:
kcapi-rng -b 9000000 > OUTFILE
The generated OUTFILE will have three huge sections that contain all
zeros, and this is caused by the code where the test
'val & PRNG_STATUS_DATA_AVAIL' fails.
Let's fix this issue by ensuring that qcom_rng_read() always returns
with a full buffer if the function returns success. Let's also have
qcom_rng_generate() return the correct value.
Here's some statistics from the ent project
(https://www.fourmilab.ch/random/) that shows information about the
quality of the generated numbers:
$ ent -c qcom-random-before
Value Char Occurrences Fraction
0 606748 0.067416
1 33104 0.003678
2 33001 0.003667
...
253 � 32883 0.003654
254 � 33035 0.003671
255 � 33239 0.003693
Total: 9000000 1.000000
Entropy = 7.811590 bits per byte.
Optimum compression would reduce the size
of this 9000000 byte file by 2 percent.
Chi square distribution for 9000000 samples is 9329962.81, and
randomly would exceed this value less than 0.01 percent of the
times.
Arithmetic mean value of data bytes is 119.3731 (127.5 = random).
Monte Carlo value for Pi is 3.197293333 (error 1.77 percent).
Serial correlation coefficient is 0.159130 (totally uncorrelated =
0.0).
Without this patch, the results of the chi-square test is 0.01%, and
the numbers are certainly not random according to ent's project page.
The results improve with this patch:
$ ent -c qcom-random-after
Value Char Occurrences Fraction
0 35432 0.003937
1 35127 0.003903
2 35424 0.003936
...
253 � 35201 0.003911
254 � 34835 0.003871
255 � 35368 0.003930
Total: 9000000 1.000000
Entropy = 7.999979 bits per byte.
Optimum compression would reduce the size
of this 9000000 byte file by 0 percent.
Chi square distribution for 9000000 samples is 258.77, and randomly
would exceed this value 42.24 percent of the times.
Arithmetic mean value of data bytes is 127.5006 (127.5 = random).
Monte Carlo value for Pi is 3.141277333 (error 0.01 percent).
Serial correlation coefficient is 0.000468 (totally uncorrelated =
0.0).
This change was tested on a Nexus 5 phone (msm8974 SoC).
Signed-off-by: Brian Masney <bmasney@redhat.com>
Fixes: ceec5f5b59 ("crypto: qcom-rng - Add Qcom prng driver")
Cc: stable@vger.kernel.org # 4.19+
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KVM's infrastructure for spectre mitigations in the vectors in v5.10 and
earlier is different, it uses templates which are used to build a set of
vectors at runtime.
There are two copy-and-paste errors in the templates: __spectre_bhb_loop_k24
should loop 24 times and __spectre_bhb_loop_k32 32.
Fix these.
Reported-by: Pavel Machek <pavel@denx.de>
Link: https://lore.kernel.org/all/20220310234858.GB16308@amd/
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f70865db5f upstream.
Revert of revert of "io_uring: wait potential ->release() on resurrect",
which adds a helper for resurrect not racing completion reinit, as was
removed because of a strange bug with no clear root or link to the
patch.
Was improved, instead of rcu_synchronize(), just wait_for_completion()
because we're at 0 refs and it will happen very shortly. Specifically
use non-interruptible version to ignore all pending signals that may
have ended prior interruptible wait.
This reverts commit cb5e1b8130.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/7a080c20f686d026efade810b116b72f88abaff9.1618101759.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b773827e36 ]
The error message when I build vm tests on debian10 (GLIBC 2.28):
userfaultfd.c: In function `userfaultfd_pagemap_test':
userfaultfd.c:1393:37: error: `MADV_PAGEOUT' undeclared (first use
in this function); did you mean `MADV_RANDOM'?
if (madvise(area_dst, test_pgsize, MADV_PAGEOUT))
^~~~~~~~~~~~
MADV_RANDOM
This patch includes these newer definitions from UAPI linux/mman.h, is
useful to fix tests build on systems without these definitions in glibc
sys/mman.h.
Link: https://lkml.kernel.org/r/20220227055330.43087-2-zhouchengming@bytedance.com
Signed-off-by: Chengming Zhou <zhouchengming@bytedance.com>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1fb205efb ]
seqno could be read as a stale value outside of the lock. The lock is
already acquired to protect the modification of seqno against a possible
race condition. Place the reading of this value also inside this locking
to protect it against a possible race condition.
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e50b88c4f0 ]
The wdev channel information is updated post channel switch only for
the station mode and not for the other modes. Due to this, the P2P client
still points to the old value though it moved to the new channel
when the channel change is induced from the P2P GO.
Update the bss channel after CSA channel switch completion for P2P client
interface as well.
Signed-off-by: Sreeramya Soratkal <quic_ssramya@quicinc.com>
Link: https://lore.kernel.org/r/1646114600-31479-1-git-send-email-quic_ssramya@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11c57c3ba9 ]
Resending this to properly add it to the patch tracker - thanks for letting
me know, Arnd :)
When ARM is enabled, and BITREVERSE is disabled,
Kbuild gives the following warning:
WARNING: unmet direct dependencies detected for HAVE_ARCH_BITREVERSE
Depends on [n]: BITREVERSE [=n]
Selected by [y]:
- ARM [=y] && (CPU_32v7M [=n] || CPU_32v7 [=y]) && !CPU_32v6 [=n]
This is because ARM selects HAVE_ARCH_BITREVERSE
without selecting BITREVERSE, despite
HAVE_ARCH_BITREVERSE depending on BITREVERSE.
This unmet dependency bug was found by Kismet,
a static analysis tool for Kconfig. Please advise if this
is not the appropriate solution.
Signed-off-by: Julian Braha <julianbraha@gmail.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2703def33 ]
After enabling CONFIG_SCHED_CORE (landed during 5.14 cycle),
2-core 2-thread-per-core interAptiv (CPS-driven) started emitting
the following:
[ 0.025698] CPU1 revision is: 0001a120 (MIPS interAptiv (multi))
[ 0.048183] ------------[ cut here ]------------
[ 0.048187] WARNING: CPU: 1 PID: 0 at kernel/sched/core.c:6025 sched_core_cpu_starting+0x198/0x240
[ 0.048220] Modules linked in:
[ 0.048233] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.17.0-rc3+ #35 b7b319f24073fd9a3c2aa7ad15fb7993eec0b26f
[ 0.048247] Stack : 817f0000 00000004 327804c8 810eb050 00000000 00000004 00000000 c314fdd1
[ 0.048278] 830cbd64 819c0000 81800000 817f0000 83070bf4 00000001 830cbd08 00000000
[ 0.048307] 00000000 00000000 815fcbc4 00000000 00000000 00000000 00000000 00000000
[ 0.048334] 00000000 00000000 00000000 00000000 817f0000 00000000 00000000 817f6f34
[ 0.048361] 817f0000 818a3c00 817f0000 00000004 00000000 00000000 4dc33260 0018c933
[ 0.048389] ...
[ 0.048396] Call Trace:
[ 0.048399] [<8105a7bc>] show_stack+0x3c/0x140
[ 0.048424] [<8131c2a0>] dump_stack_lvl+0x60/0x80
[ 0.048440] [<8108b5c0>] __warn+0xc0/0xf4
[ 0.048454] [<8108b658>] warn_slowpath_fmt+0x64/0x10c
[ 0.048467] [<810bd418>] sched_core_cpu_starting+0x198/0x240
[ 0.048483] [<810c6514>] sched_cpu_starting+0x14/0x80
[ 0.048497] [<8108c0f8>] cpuhp_invoke_callback_range+0x78/0x140
[ 0.048510] [<8108d914>] notify_cpu_starting+0x94/0x140
[ 0.048523] [<8106593c>] start_secondary+0xbc/0x280
[ 0.048539]
[ 0.048543] ---[ end trace 0000000000000000 ]---
[ 0.048636] Synchronize counters for CPU 1: done.
...for each but CPU 0/boot.
Basic debug printks right before the mentioned line say:
[ 0.048170] CPU: 1, smt_mask:
So smt_mask, which is sibling mask obviously, is empty when entering
the function.
This is critical, as sched_core_cpu_starting() calculates
core-scheduling parameters only once per CPU start, and it's crucial
to have all the parameters filled in at that moment (at least it
uses cpu_smt_mask() which in fact is `&cpu_sibling_map[cpu]` on
MIPS).
A bit of debugging led me to that set_cpu_sibling_map() performing
the actual map calculation, was being invocated after
notify_cpu_start(), and exactly the latter function starts CPU HP
callback round (sched_core_cpu_starting() is basically a CPU HP
callback).
While the flow is same on ARM64 (maps after the notifier, although
before calling set_cpu_online()), x86 started calculating sibling
maps earlier than starting the CPU HP callbacks in Linux 4.14 (see
[0] for the reference). Neither me nor my brief tests couldn't find
any potential caveats in calculating the maps right after performing
delay calibration, but the WARN splat is now gone.
The very same debug prints now yield exactly what I expected from
them:
[ 0.048433] CPU: 1, smt_mask: 0-1
[0] https://git.kernel.org/pub/scm/linux/kernel/git/mips/linux.git/commit/?id=76ce7cfe35ef
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 268a491aeb ]
The DWC2 USB controller on the Agilex platform does not support clock
gating, so use the chip specific "intel,socfpga-agilex-hsotg"
compatible.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e03c3bba35 ]
xfrm_migrate cannot handle address family change of an xfrm_state.
The symptons are the xfrm_state will be migrated to a wrong address,
and sending as well as receiving packets wil be broken.
This commit fixes it by breaking the original xfrm_state_clone
method into two steps so as to update the props.family before
running xfrm_init_state. As the result, xfrm_state's inner mode,
outer mode, type and IP header length in xfrm_state_migrate can
be updated with the new address family.
Tested with additions to Android's kernel unit test suite:
https://android-review.googlesource.com/c/kernel/tests/+/1885354
Signed-off-by: Yan Yan <evitayan@google.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1aca3080e ]
This patch enables distinguishing SAs and SPs based on if_id during
the xfrm_migrate flow. This ensures support for xfrm interfaces
throughout the SA/SP lifecycle.
When there are multiple existing SPs with the same direction,
the same xfrm_selector and different endpoint addresses,
xfrm_migrate might fail with ENODATA.
Specifically, the code path for performing xfrm_migrate is:
Stage 1: find policy to migrate with
xfrm_migrate_policy_find(sel, dir, type, net)
Stage 2: find and update state(s) with
xfrm_migrate_state_find(mp, net)
Stage 3: update endpoint address(es) of template(s) with
xfrm_policy_migrate(pol, m, num_migrate)
Currently "Stage 1" always returns the first xfrm_policy that
matches, and "Stage 3" looks for the xfrm_tmpl that matches the
old endpoint address. Thus if there are multiple xfrm_policy
with same selector, direction, type and net, "Stage 1" might
rertun a wrong xfrm_policy and "Stage 3" will fail with ENODATA
because it cannot find a xfrm_tmpl with the matching endpoint
address.
The fix is to allow userspace to pass an if_id and add if_id
to the matching rule in Stage 1 and Stage 2 since if_id is a
unique ID for xfrm_policy and xfrm_state. For compatibility,
if_id will only be checked if the attribute is set.
Tested with additions to Android's kernel unit test suite:
https://android-review.googlesource.com/c/kernel/tests/+/1668886
Signed-off-by: Yan Yan <evitayan@google.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit eae5783908 upstream.
This patch fixes the problems below:
1. In non-shutdown_ack_sent states: in sctp_sf_do_5_1B_init() and
sctp_sf_do_5_2_2_dupinit():
chunk length check should be done before any checks that may cause
to send abort, as making packet for abort will access the init_tag
from init_hdr in sctp_ootb_pkt_new().
2. In shutdown_ack_sent state: in sctp_sf_do_9_2_reshutack():
The same checks as does in sctp_sf_do_5_2_2_dupinit() is needed
for sctp_sf_do_9_2_reshutack().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c993ee0f9f upstream.
In watch_queue_set_filter(), there are a couple of places where we check
that the filter type value does not exceed what the type_filter bitmap
can hold. One place calculates the number of bits by:
if (tf[i].type >= sizeof(wfilter->type_filter) * 8)
which is fine, but the second does:
if (tf[i].type >= sizeof(wfilter->type_filter) * BITS_PER_LONG)
which is not. This can lead to a couple of out-of-bounds writes due to
a too-large type:
(1) __set_bit() on wfilter->type_filter
(2) Writing more elements in wfilter->filters[] than we allocated.
Fix this by just using the proper WATCH_TYPE__NR instead, which is the
number of types we actually know about.
The bug may cause an oops looking something like:
BUG: KASAN: slab-out-of-bounds in watch_queue_set_filter+0x659/0x740
Write of size 4 at addr ffff88800d2c66bc by task watch_queue_oob/611
...
Call Trace:
<TASK>
dump_stack_lvl+0x45/0x59
print_address_description.constprop.0+0x1f/0x150
...
kasan_report.cold+0x7f/0x11b
...
watch_queue_set_filter+0x659/0x740
...
__x64_sys_ioctl+0x127/0x190
do_syscall_64+0x43/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
Allocated by task 611:
kasan_save_stack+0x1e/0x40
__kasan_kmalloc+0x81/0xa0
watch_queue_set_filter+0x23a/0x740
__x64_sys_ioctl+0x127/0x190
do_syscall_64+0x43/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
The buggy address belongs to the object at ffff88800d2c66a0
which belongs to the cache kmalloc-32 of size 32
The buggy address is located 28 bytes inside of
32-byte region [ffff88800d2c66a0, ffff88800d2c66c0)
Fixes: c73be61ced ("pipe: Add general notification queue support")
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c7cb60bff upstream.
When building for Thumb2, the vectors make use of a local label. Sadly,
the Spectre BHB code also uses a local label with the same number which
results in the Thumb2 reference pointing at the wrong place. Fix this
by changing the number used for the Spectre BHB local label.
Fixes: b9baf5c8c5 ("ARM: Spectre-BHB workaround")
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1489186cc upstream.
The in-kernel ext4 resize code doesn't support filesystem with the
sparse_super2 feature. It fails with errors like this and doesn't finish
the resize:
EXT4-fs (loop0): resizing filesystem from 16640 to 7864320 blocks
EXT4-fs warning (device loop0): verify_reserved_gdb:760: reserved GDT 2 missing grp 1 (32770)
EXT4-fs warning (device loop0): ext4_resize_fs:2111: error (-22) occurred during file system resize
EXT4-fs (loop0): resized filesystem to 2097152
To reproduce:
mkfs.ext4 -b 4096 -I 256 -J size=32 -E resize=$((256*1024*1024)) -O sparse_super2 ext4.img 65M
truncate -s 30G ext4.img
mount ext4.img /mnt
python3 -c 'import fcntl, os, struct ; fd = os.open("/mnt", os.O_RDONLY | os.O_DIRECTORY) ; fcntl.ioctl(fd, 0x40086610, struct.pack("Q", 30 * 1024 * 1024 * 1024 // 4096), False) ; os.close(fd)'
dmesg | tail
e2fsck ext4.img
The userspace resize2fs tool has a check for this case: it checks if the
filesystem has sparse_super2 set and if the kernel provides
/sys/fs/ext4/features/sparse_super2. However, the former check requires
manually reading and parsing the filesystem superblock.
Detect this case in ext4_resize_begin and error out early with a clear
error message.
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Link: https://lore.kernel.org/r/74b8ae78405270211943cd7393e65586c5faeed1.1623093259.git.josh@joshtriplett.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7228918b34 upstream.
As documented, the setup_indirect structure is nested inside
the setup_data structures in the setup_data list. The code currently
accesses the fields inside the setup_indirect structure but only
the sizeof(struct setup_data) is being memremapped. No crash
occurred but this is just due to how the area is remapped under the
covers.
Properly memremap both the setup_data and setup_indirect structures
in these cases before accessing them.
Fixes: b3c72fc9a7 ("x86/boot: Introduce setup_indirect")
Signed-off-by: Ross Philipson <ross.philipson@oracle.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1645668456-22036-2-git-send-email-ross.philipson@oracle.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4edc076041 upstream.
watch_queue_clear() has a comment stating that setting ->defunct to true
preventing new additions as well as preventing notifications. Whilst
the latter is true, the first bit is superfluous since at the time this
function is called, the pipe cannot be accessed to add new event
sources.
Remove the "new additions" bit from the comment.
Fixes: c73be61ced ("pipe: Add general notification queue support")
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2ed147f015 upstream.
There's nothing to synchronise post_one_notification() versus
pipe_read(). Whilst posting is done under pipe->rd_wait.lock, the
reader only takes pipe->mutex which cannot bar notification posting as
that may need to be made from contexts that cannot sleep.
Fix this by setting pipe->head with a barrier in post_one_notification()
and reading pipe->head with a barrier in pipe_read().
If that's not sufficient, the rd_wait.lock will need to be taken,
possibly in a ->confirm() op so that it only applies to notifications.
The lock would, however, have to be dropped before copy_page_to_iter()
is invoked.
Fixes: c73be61ced ("pipe: Add general notification queue support")
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b4c037192 upstream.
Currently, watch_queue_set_size() sets the number of notes available in
wqueue->nr_notes according to the number of notes allocated, but sets
the size of the bitmap to the unrounded number of notes originally asked
for.
Fix this by setting the bitmap size to the number of notes we're
actually going to make available (ie. the number allocated).
Fixes: c73be61ced ("pipe: Add general notification queue support")
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 96a4d8912b upstream.
The pipe ring size must always be a power of 2 as the head and tail
pointers are masked off by AND'ing with the size of the ring - 1.
watch_queue_set_size(), however, lets you specify any number of notes
between 1 and 511. This number is passed through to pipe_resize_ring()
without checking/forcing its alignment.
Fix this by rounding the number of slots required up to the nearest
power of two. The request is meant to guarantee that at least that many
notifications can be generated before the queue is full, so rounding
down isn't an option, but, alternatively, it may be better to give an
error if we aren't allowed to allocate that much ring space.
Fixes: c73be61ced ("pipe: Add general notification queue support")
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1853fbadc upstream.
When a pipe ring descriptor points to a notification message, the
refcount on the backing page is incremented by the generic get function,
but the release function, which marks the bitmap, doesn't drop the page
ref.
Fix this by calling generic_pipe_buf_release() at the end of
watch_queue_pipe_buf_release().
Fixes: c73be61ced ("pipe: Add general notification queue support")
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db8facfc9f upstream.
In free_pipe_info(), free the watchqueue state after clearing the pipe
ring as each pipe ring descriptor has a release function, and in the
case of a notification message, this is watch_queue_pipe_buf_release()
which tries to mark the allocation bitmap that was previously released.
Fix this by moving the put of the pipe's ref on the watch queue to after
the ring has been cleared. We still need to call watch_queue_clear()
before doing that to make sure that the pipe is disconnected from any
notification sources first.
Fixes: c73be61ced ("pipe: Add general notification queue support")
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4fa59ede95 upstream.
The feature negotiation was designed in a way that
makes it possible for devices to know which config
fields will be accessed by drivers.
This is broken since commit 404123c2db ("virtio: allow drivers to
validate features") with fallout in at least block and net. We have a
partial work-around in commit 2f9a174f91 ("virtio: write back
F_VERSION_1 before validate") which at least lets devices find out which
format should config space have, but this is a partial fix: guests
should not access config space without acknowledging features since
otherwise we'll never be able to change the config space format.
To fix, split finalize_features from virtio_finalize_features and
call finalize_features with all feature bits before validation,
and then - if validation changed any bits - once again after.
Since virtio_finalize_features no longer writes out features
rename it to virtio_features_ok - since that is what it does:
checks that features are ok with the device.
As a side effect, this also reduces the amount of hypervisor accesses -
we now only acknowledge features once unless we are clearing any
features when validating (which is uncommon).
IRC I think that this was more or less always the intent in the spec but
unfortunately the way the spec is worded does not say this explicitly, I
plan to address this at the spec level, too.
Acked-by: Jason Wang <jasowang@redhat.com>
Cc: stable@vger.kernel.org
Fixes: 404123c2db ("virtio: allow drivers to validate features")
Fixes: 2f9a174f91 ("virtio: write back F_VERSION_1 before validate")
Cc: "Halil Pasic" <pasic@linux.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a1cc1697bb upstream.
Legacy and old PCI I/O based cards do not support 32-bit I/O addressing.
Since commit 64f160e19e ("PCI: aardvark: Configure PCIe resources from
'ranges' DT property") kernel can set different PCIe address on CPU and
different on the bus for the one A37xx address mapping without any firmware
support in case the bus address does not conflict with other A37xx mapping.
So remap I/O space to the bus address 0x0 to enable support for old legacy
I/O port based cards which have hardcoded I/O ports in low address space.
Note that DDR on A37xx is mapped to bus address 0x0. And mapping of I/O
space can be set to address 0x0 too because MEM space and I/O space are
separate and so do not conflict.
Remapping IO space on Turris Mox to different address is not possible to
due bootloader bug.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 76f6386b25 ("arm64: dts: marvell: Add Aardvark PCIe support for Armada 3700")
Cc: stable@vger.kernel.org # 64f160e19e ("PCI: aardvark: Configure PCIe resources from 'ranges' DT property")
Cc: stable@vger.kernel.org # 514ef1e62d ("arm64: dts: marvell: armada-37xx: Extend PCIe MEM space")
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0966d38583 upstream.
RISC-V can do PC-relative jumps with a 32bit range using the following
two instructions:
auipc t0, imm20 ; t0 = PC + imm20 * 2^12
jalr ra, t0, imm12 ; ra = PC + 4, PC = t0 + imm12
Crucially both the 20bit immediate imm20 and the 12bit immediate imm12
are treated as two's-complement signed values. For this reason the
immediates are usually calculated like this:
imm20 = (offset + 0x800) >> 12
imm12 = offset & 0xfff
..where offset is the signed offset from the auipc instruction. When
the 11th bit of offset is 0 the addition of 0x800 doesn't change the top
20 bits and imm12 considered positive. When the 11th bit is 1 the carry
of the addition by 0x800 means imm20 is one higher, but since imm12 is
then considered negative the two's complement representation means it
all cancels out nicely.
However, this addition by 0x800 (2^11) means an offset greater than or
equal to 2^31 - 2^11 would overflow so imm20 is considered negative and
result in a backwards jump. Similarly the lower range of offset is also
moved down by 2^11 and hence the true 32bit range is
[-2^31 - 2^11, 2^31 - 2^11)
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Fixes: e2c0cdfba7 ("RISC-V: User-facing API")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0bf476fc36 upstream.
There is an oddity in the way the RSR register flags propagate to the
ISR register (and the actual interrupt output) on this hardware: it
appears that RSR register bits only result in ISR being asserted if the
interrupt was actually enabled at the time, so enabling interrupts with
RSR bits already set doesn't trigger an interrupt to be raised. There
was already a partial fix for this race in the macb_poll function where
it checked for RSR bits being set and re-triggered NAPI receive.
However, there was a still a race window between checking RSR and
actually enabling interrupts, where a lost wakeup could happen. It's
necessary to check again after enabling interrupts to see if RSR was set
just prior to the interrupt being enabled, and re-trigger receive in that
case.
This issue was noticed in a point-to-point UDP request-response protocol
which periodically saw timeouts or abnormally high response times due to
received packets not being processed in a timely fashion. In many
applications, more packets arriving, including TCP retransmissions, would
cause the original packet to be processed, thus masking the issue.
Fixes: 02f7a34f34 ("net: macb: Re-enable RX interrupt only when RX is done")
Cc: stable@vger.kernel.org
Co-developed-by: Scott McNutt <scott.mcnutt@siriusxm.com>
Signed-off-by: Scott McNutt <scott.mcnutt@siriusxm.com>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f4347081b upstream.
Commit 54659ca026 ("staging: rtl8723bs: remove possible deadlock when
disconnect (v2)") split the locking of pxmitpriv->lock vs sleep_q/lock
into 2 locks in attempt to fix a lockdep reported issue with the locking
order of the sta_hash_lock vs pxmitpriv->lock.
But in the end this turned out to not fully solve the sta_hash_lock issue
so commit a7ac783c33 ("staging: rtl8723bs: remove a second possible
deadlock") was added to fix this in another way.
The original fix was kept as it was still seen as a good thing to have,
but now it turns out that it creates a deadlock in access-point mode:
[Feb20 23:47] ======================================================
[ +0.074085] WARNING: possible circular locking dependency detected
[ +0.074077] 5.16.0-1-amd64 #1 Tainted: G C E
[ +0.064710] ------------------------------------------------------
[ +0.074075] ksoftirqd/3/29 is trying to acquire lock:
[ +0.060542] ffffb8b30062ab00 (&pxmitpriv->lock){+.-.}-{2:2}, at: rtw_xmit_classifier+0x8a/0x140 [r8723bs]
[ +0.114921]
but task is already holding lock:
[ +0.069908] ffffb8b3007ab704 (&psta->sleep_q.lock){+.-.}-{2:2}, at: wakeup_sta_to_xmit+0x3b/0x300 [r8723bs]
[ +0.116976]
which lock already depends on the new lock.
[ +0.098037]
the existing dependency chain (in reverse order) is:
[ +0.089704]
-> #1 (&psta->sleep_q.lock){+.-.}-{2:2}:
[ +0.077232] _raw_spin_lock_bh+0x34/0x40
[ +0.053261] xmitframe_enqueue_for_sleeping_sta+0xc1/0x2f0 [r8723bs]
[ +0.082572] rtw_xmit+0x58b/0x940 [r8723bs]
[ +0.056528] _rtw_xmit_entry+0xba/0x350 [r8723bs]
[ +0.062755] dev_hard_start_xmit+0xf1/0x320
[ +0.056381] sch_direct_xmit+0x9e/0x360
[ +0.052212] __dev_queue_xmit+0xce4/0x1080
[ +0.055334] ip6_finish_output2+0x18f/0x6e0
[ +0.056378] ndisc_send_skb+0x2c8/0x870
[ +0.052209] ndisc_send_ns+0xd3/0x210
[ +0.050130] addrconf_dad_work+0x3df/0x5a0
[ +0.055338] process_one_work+0x274/0x5a0
[ +0.054296] worker_thread+0x52/0x3b0
[ +0.050124] kthread+0x16c/0x1a0
[ +0.044925] ret_from_fork+0x1f/0x30
[ +0.049092]
-> #0 (&pxmitpriv->lock){+.-.}-{2:2}:
[ +0.074101] __lock_acquire+0x10f5/0x1d80
[ +0.054298] lock_acquire+0xd7/0x300
[ +0.049088] _raw_spin_lock_bh+0x34/0x40
[ +0.053248] rtw_xmit_classifier+0x8a/0x140 [r8723bs]
[ +0.066949] rtw_xmitframe_enqueue+0xa/0x20 [r8723bs]
[ +0.066946] rtl8723bs_hal_xmitframe_enqueue+0x14/0x50 [r8723bs]
[ +0.078386] wakeup_sta_to_xmit+0xa6/0x300 [r8723bs]
[ +0.065903] rtw_recv_entry+0xe36/0x1160 [r8723bs]
[ +0.063809] rtl8723bs_recv_tasklet+0x349/0x6c0 [r8723bs]
[ +0.071093] tasklet_action_common.constprop.0+0xe5/0x110
[ +0.070966] __do_softirq+0x16f/0x50a
[ +0.050134] __irq_exit_rcu+0xeb/0x140
[ +0.051172] irq_exit_rcu+0xa/0x20
[ +0.047006] common_interrupt+0xb8/0xd0
[ +0.052214] asm_common_interrupt+0x1e/0x40
[ +0.056381] finish_task_switch.isra.0+0x100/0x3a0
[ +0.063670] __schedule+0x3ad/0xd20
[ +0.048047] schedule+0x4e/0xc0
[ +0.043880] smpboot_thread_fn+0xc4/0x220
[ +0.054298] kthread+0x16c/0x1a0
[ +0.044922] ret_from_fork+0x1f/0x30
[ +0.049088]
other info that might help us debug this:
[ +0.095950] Possible unsafe locking scenario:
[ +0.070952] CPU0 CPU1
[ +0.054282] ---- ----
[ +0.054285] lock(&psta->sleep_q.lock);
[ +0.047004] lock(&pxmitpriv->lock);
[ +0.074082] lock(&psta->sleep_q.lock);
[ +0.077209] lock(&pxmitpriv->lock);
[ +0.043873]
*** DEADLOCK ***
[ +0.070950] 1 lock held by ksoftirqd/3/29:
[ +0.049082] #0: ffffb8b3007ab704 (&psta->sleep_q.lock){+.-.}-{2:2}, at: wakeup_sta_to_xmit+0x3b/0x300 [r8723bs]
Analysis shows that in hindsight the splitting of the lock was not
a good idea, so revert this to fix the access-point mode deadlock.
Note this is a straight-forward revert done with git revert, the commented
out "/* spin_lock_bh(&psta_bmc->sleep_q.lock); */" lines were part of the
code before the reverted changes.
Fixes: 54659ca026 ("staging: rtl8723bs: remove possible deadlock when disconnect (v2)")
Cc: stable <stable@vger.kernel.org>
Cc: Fabio Aiuto <fabioaiuto83@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=215542
Link: https://lore.kernel.org/r/20220302101637.26542-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c4bcfdecb upstream.
In FOPEN_DIRECT_IO mode, fuse_file_write_iter() calls
fuse_direct_write_iter(), which normally calls fuse_direct_io(), which then
imports the write buffer with fuse_get_user_pages(), which uses
iov_iter_get_pages() to grab references to userspace pages instead of
actually copying memory.
On the filesystem device side, these pages can then either be read to
userspace (via fuse_dev_read()), or splice()d over into a pipe using
fuse_dev_splice_read() as pipe buffers with &nosteal_pipe_buf_ops.
This is wrong because after fuse_dev_do_read() unlocks the FUSE request,
the userspace filesystem can mark the request as completed, causing write()
to return. At that point, the userspace filesystem should no longer have
access to the pipe buffer.
Fix by copying pages coming from the user address space to new pipe
buffers.
Reported-by: Jann Horn <jannh@google.com>
Fixes: c3021629a0 ("fuse: support splice() reading from fuse device")
Cc: <stable@vger.kernel.org>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6845376713 upstream.
When CONFIG_GENERIC_CPU_VULNERABILITIES is not set, references
to spectre_v2_update_state() cause a build error, so provide an
empty stub for that function when the Kconfig option is not set.
Fixes this build error:
arm-linux-gnueabi-ld: arch/arm/mm/proc-v7-bugs.o: in function `cpu_v7_bugs_init':
proc-v7-bugs.c:(.text+0x52): undefined reference to `spectre_v2_update_state'
arm-linux-gnueabi-ld: proc-v7-bugs.c:(.text+0x82): undefined reference to `spectre_v2_update_state'
Fixes: b9baf5c8c5 ("ARM: Spectre-BHB workaround")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: patches@armlinux.org.uk
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fda153c89a ]
Running the memfd script ./run_hugetlbfs_test.sh will often end in error
as follows:
memfd-hugetlb: CREATE
memfd-hugetlb: BASIC
memfd-hugetlb: SEAL-WRITE
memfd-hugetlb: SEAL-FUTURE-WRITE
memfd-hugetlb: SEAL-SHRINK
fallocate(ALLOC) failed: No space left on device
./run_hugetlbfs_test.sh: line 60: 166855 Aborted (core dumped) ./memfd_test hugetlbfs
opening: ./mnt/memfd
fuse: DONE
If no hugetlb pages have been preallocated, run_hugetlbfs_test.sh will
allocate 'just enough' pages to run the test. In the SEAL-FUTURE-WRITE
test the mfd_fail_write routine maps the file, but does not unmap. As a
result, two hugetlb pages remain reserved for the mapping. When the
fallocate call in the SEAL-SHRINK test attempts allocate all hugetlb
pages, it is short by the two reserved pages.
Fix by making sure to unmap in mfd_fail_write.
Link: https://lkml.kernel.org/r/20220219004340.56478-1-mike.kravetz@oracle.com
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Joel Fernandes <joel@joelfernandes.org>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8240addd0 ]
This reverts commit 2afeec08ab.
The reasoning in the commit was wrong - the code expected to setup the
watch even if 'hotplug-status' didn't exist. In fact, it relied on the
watch being fired the first time - to check if maybe 'hotplug-status' is
already set to 'connected'. Not registering a watch for non-existing
path (which is the case if hotplug script hasn't been executed yet),
made the backend not waiting for the hotplug script to execute. This in
turns, made the netfront think the interface is fully operational, while
in fact it was not (the vif interface on xen-netback side might not be
configured yet).
This was a workaround for 'hotplug-status' erroneously being removed.
But since that is reverted now, the workaround is not necessary either.
More discussion at
https://lore.kernel.org/xen-devel/afedd7cb-a291-e773-8b0d-4db9b291fa98@ipxe.org/T/#u
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Reviewed-by: Michael Brown <mbrown@fensystems.co.uk>
Link: https://lore.kernel.org/r/20220222001817.2264967-2-marmarek@invisiblethingslab.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f4558ae91 ]
This reverts commit 1f2565780e.
The 'hotplug-status' node should not be removed as long as the vif
device remains configured. Otherwise the xen-netback would wait for
re-running the network script even if it was already called (in case of
the frontent re-connecting). But also, it _should_ be removed when the
vif device is destroyed (for example when unbinding the driver) -
otherwise hotplug script would not configure the device whenever it
re-appear.
Moving removal of the 'hotplug-status' node was a workaround for nothing
calling network script after xen-netback module is reloaded. But when
vif interface is re-created (on xen-netback unbind/bind for example),
the script should be called, regardless of who does that - currently
this case is not handled by the toolstack, and requires manual
script call. Keeping hotplug-status=connected to skip the call is wrong
and leads to not configured interface.
More discussion at
https://lore.kernel.org/xen-devel/afedd7cb-a291-e773-8b0d-4db9b291fa98@ipxe.org/T/#u
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Link: https://lore.kernel.org/r/20220222001817.2264967-1-marmarek@invisiblethingslab.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae42f92888 ]
We are racing the registering of .to_irq when probing the
i2c driver. This results in random failure of touchscreen
devices.
Following explains the race condition better.
[gpio driver] gpio driver registers gpio chip
[gpio consumer] gpio is acquired
[gpio consumer] gpiod_to_irq() fails with -ENXIO
[gpio driver] gpio driver registers irqchip
gpiod_to_irq works at this point, but -ENXIO is fatal
We could see the following errors in dmesg logs when gc->to_irq is NULL
[2.101857] i2c_hid i2c-FTS3528:00: HID over i2c has not been provided an Int IRQ
[2.101953] i2c_hid: probe of i2c-FTS3528:00 failed with error -22
To avoid this situation, defer probing until to_irq is registered.
Returning -EPROBE_DEFER would be the first step towards avoiding
the failure of devices due to the race in registration of .to_irq.
Final solution to this issue would be to avoid using gc irq members
until they are fully initialized.
This issue has been reported many times in past and people have been
using workarounds like changing the pinctrl_amd to built-in instead
of loading it as a module or by adding a softdep for pinctrl_amd into
the config file.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=209413
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Shreeya Patel <shreeya.patel@collabora.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 00b022f8f8 ]
Some of the bcmgenet platforms don't correctly support WOL, yet
ethtool returns:
"Supports Wake-on: gsf"
which is false.
Ideally if there isn't a wol_irq, or there is something else that
keeps the device from being able to wakeup it should display:
"Supports Wake-on: d"
This patch checks whether the device can wakup, before using the
hard-coded supported flags. This corrects the ethtool reporting, as
well as the WOL configuration because ethtool verifies that the mode
is supported before attempting it.
Fixes: c51de7f397 ("net: bcmgenet: add Wake-on-LAN support code")
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220310045535.224450-1-jeremy.linton@arm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03fe003547 ]
This works around an issue with the hardware where both OE and
DAT are exposed in the same register. If both are updated
simultaneously, the harware makes no guarantees that OE or DAT
will actually change in any given order and may result in a
glitch of a few ns on a GPIO pin when changing direction and value
in a single write.
Setting direction to input now only affects OE bit. Setting
direction to output updates DAT first, then OE.
Fixes: 9c6686322d ("gpio: add Technologic I2C-FPGA gpio support")
Signed-off-by: Mark Featherston <mark@embeddedTS.com>
Signed-off-by: Kris Bahnsen <kris@embeddedTS.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 18dfc66755 ]
The cleanup() function takes care of killing processes launched by the
test functions. It relies on variables like ${tcpdump_pids} to get the
relevant PIDs. But tests are run in their own subshell, so updated
*_pids values are invisible to other shells. Therefore cleanup() never
sees any process to kill:
$ ./tools/testing/selftests/net/pmtu.sh -t pmtu_ipv4_exception
TEST: ipv4: PMTU exceptions [ OK ]
TEST: ipv4: PMTU exceptions - nexthop objects [ OK ]
$ pgrep -af tcpdump
6084 tcpdump -s 0 -i veth_A-R1 -w pmtu_ipv4_exception_veth_A-R1.pcap
6085 tcpdump -s 0 -i veth_R1-A -w pmtu_ipv4_exception_veth_R1-A.pcap
6086 tcpdump -s 0 -i veth_R1-B -w pmtu_ipv4_exception_veth_R1-B.pcap
6087 tcpdump -s 0 -i veth_B-R1 -w pmtu_ipv4_exception_veth_B-R1.pcap
6088 tcpdump -s 0 -i veth_A-R2 -w pmtu_ipv4_exception_veth_A-R2.pcap
6089 tcpdump -s 0 -i veth_R2-A -w pmtu_ipv4_exception_veth_R2-A.pcap
6090 tcpdump -s 0 -i veth_R2-B -w pmtu_ipv4_exception_veth_R2-B.pcap
6091 tcpdump -s 0 -i veth_B-R2 -w pmtu_ipv4_exception_veth_B-R2.pcap
6228 tcpdump -s 0 -i veth_A-R1 -w pmtu_ipv4_exception_veth_A-R1.pcap
6229 tcpdump -s 0 -i veth_R1-A -w pmtu_ipv4_exception_veth_R1-A.pcap
6230 tcpdump -s 0 -i veth_R1-B -w pmtu_ipv4_exception_veth_R1-B.pcap
6231 tcpdump -s 0 -i veth_B-R1 -w pmtu_ipv4_exception_veth_B-R1.pcap
6232 tcpdump -s 0 -i veth_A-R2 -w pmtu_ipv4_exception_veth_A-R2.pcap
6233 tcpdump -s 0 -i veth_R2-A -w pmtu_ipv4_exception_veth_R2-A.pcap
6234 tcpdump -s 0 -i veth_R2-B -w pmtu_ipv4_exception_veth_R2-B.pcap
6235 tcpdump -s 0 -i veth_B-R2 -w pmtu_ipv4_exception_veth_B-R2.pcap
Fix this by running cleanup() in the context of the test subshell.
Now that each test cleans the environment after completion, there's no
need for calling cleanup() again when the next test starts. So let's
drop it from the setup() function. This is okay because cleanup() is
also called when pmtu.sh starts, so even the first test starts in a
clean environment.
Also, use tcpdump's immediate mode. Otherwise it might not have time to
process buffered packets, resulting in missing packets or even empty
pcap files for short tests.
Note: PAUSE_ON_FAIL is still evaluated before cleanup(), so one can
still inspect the test environment upon failure when using -p.
Fixes: a92a0a7b8e ("selftests: pmtu: Simplify cleanup and namespace names")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad11c4f1d8 ]
There could be multiple multipath entries but changing the port affinity
for each one doesn't make much sense and there should be a default one.
So only track the entry with lowest priority value.
The commit doesn't affect existing users with a single entry.
Fixes: 544fe7c2e6 ("net/mlx5e: Activate HW multipath and handle port affinity based on FIB events")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 063bd35559 ]
Fix a refcount use after free warning due to a race on command entry.
Such race occurs when one of the commands releases its last refcount and
frees its index and entry while another process running command flush
flow takes refcount to this command entry. The process which handles
commands flush may see this command as needed to be flushed if the other
process released its refcount but didn't release the index yet. Fix it
by adding the needed spin lock.
It fixes the following warning trace:
refcount_t: addition on 0; use-after-free.
WARNING: CPU: 11 PID: 540311 at lib/refcount.c:25 refcount_warn_saturate+0x80/0xe0
...
RIP: 0010:refcount_warn_saturate+0x80/0xe0
...
Call Trace:
<TASK>
mlx5_cmd_trigger_completions+0x293/0x340 [mlx5_core]
mlx5_cmd_flush+0x3a/0xf0 [mlx5_core]
enter_error_state+0x44/0x80 [mlx5_core]
mlx5_fw_fatal_reporter_err_work+0x37/0xe0 [mlx5_core]
process_one_work+0x1be/0x390
worker_thread+0x4d/0x3d0
? rescuer_thread+0x350/0x350
kthread+0x141/0x160
? set_kthread_struct+0x40/0x40
ret_from_fork+0x1f/0x30
</TASK>
Fixes: 50b2412b7e ("net/mlx5: Avoid possible free of command entry while timeout comp handler")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac77998b7a ]
According to HW spec the field "size" should be 16 bits
in bufferx register.
Fixes: e281682bf2 ("net/mlx5_core: HW data structs/types definitions cleanup")
Signed-off-by: Mohammad Kabat <mohammadkab@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71171ac8eb ]
When two ax25 devices attempted to establish connection, the requester use ax25_create(),
ax25_bind() and ax25_connect() to initiate connection. The receiver use ax25_rcv() to
accept connection and use ax25_create_cb() in ax25_rcv() to create ax25_cb, but the
ax25_cb->sk is NULL. When the receiver is detaching, a NULL pointer dereference bug
caused by sock_hold(sk) in ax25_kill_by_device() will happen. The corresponding
fail log is shown below:
===============================================================
BUG: KASAN: null-ptr-deref in ax25_device_event+0xfd/0x290
Call Trace:
...
ax25_device_event+0xfd/0x290
raw_notifier_call_chain+0x5e/0x70
dev_close_many+0x174/0x220
unregister_netdevice_many+0x1f7/0xa60
unregister_netdevice_queue+0x12f/0x170
unregister_netdev+0x13/0x20
mkiss_close+0xcd/0x140
tty_ldisc_release+0xc0/0x220
tty_release_struct+0x17/0xa0
tty_release+0x62d/0x670
...
This patch add condition check in ax25_kill_by_device(). If s->sk is
NULL, it will goto if branch to kill device.
Fixes: 4e0f718daf ("ax25: improve the incomplete fix to avoid UAF and NPD bugs")
Reported-by: Thomas Osterried <thomas@osterried.de>
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2169b79258 ]
As the potential failure of the clk_enable(),
it should be better to check it and return error
if fails.
Fixes: b7370112f5 ("lpc32xx: Added ethernet driver")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6babfc6e6f ]
As the potential failure of the clk_enable(),
it should be better to check it and return error
if fails.
Fixes: 8a2c9a5ab4 ("net: ethernet: ti: cpts: rework initialization/deinitialization")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c79fcc27be ]
When receiving a state message, function tipc_link_validate_msg()
is called to validate its header portion. Then, its data portion
is validated before it can be accessed correctly. However, current
data sanity check is done after the message header is accessed to
update some link variables.
This commit fixes this issue by moving the data sanity check to
the beginning of state message handling and right after the header
sanity check.
Fixes: 9aa422ad32 ("tipc: improve size validations for received domain records")
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Link: https://lore.kernel.org/r/20220308021200.9245-1-tung.q.nguyen@dektech.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad35ffa252 ]
Change curr_link_speed advertised speed, due to
link_info.link_speed is not equal phy.curr_user_speed_req.
Without this patch it is impossible to set advertised
speed to same as link_speed.
Testing Hints: Try to set advertised speed
to 25G only with 25G default link (use ethtool -s 0x80000000)
Fixes: 48cb27f2fd ("ice: Implement handlers for ethtool PHY/link operations")
Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6730a871e ]
For get PHY abilities AQ, the specification defines "report modes"
as "with media", "without media" and "active configuration". For
clarity, rename macros to align with the specification.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79498d5af8 ]
The ice_vc_send_msg_to_vf function has logic to detect "failure"
responses being sent to a VF. If a VF is sent more than
ICE_DFLT_NUM_INVAL_MSGS_ALLOWED then the VF is marked as disabled.
Almost identical logic also existed in the i40e driver.
This logic was added to the ice driver in commit 1071a8358a ("ice:
Implement virtchnl commands for AVF support") which itself copied from
the i40e implementation in commit 5c3c48ac6b ("i40e: implement virtual
device interface").
Neither commit provides a proper explanation or justification of the
check. In fact, later commits to i40e changed the logic to allow
bypassing the check in some specific instances.
The "logic" for this seems to be that error responses somehow indicate a
malicious VF. This is not really true. The PF might be sending an error
for any number of reasons such as lack of resources, etc.
Additionally, this causes the PF to log an info message for every failed
VF response which may confuse users, and can spam the kernel log.
This behavior is not documented as part of any requirement for our
products and other operating system drivers such as the FreeBSD
implementation of our drivers do not include this type of check.
In fact, the change from dev_err to dev_info in i40e commit 18b7af57d9
("i40e: Lower some message levels") explains that these messages
typically don't actually indicate a real issue. It is quite likely that
a user who hits this in practice will be very confused as the VF will be
disabled without an obvious way to recover.
We already have robust malicious driver detection logic using actual
hardware detection mechanisms that detect and prevent invalid device
usage. Remove the logic since its not a documented requirement and the
behavior is not intuitive.
Fixes: 1071a8358a ("ice: Implement virtchnl commands for AVF support")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5710ab7916 ]
The i40e_vc_send_msg_to_vf_ex (and its wrapper i40e_vc_send_msg_to_vf)
function has logic to detect "failure" responses sent to the VF. If a VF
is sent more than I40E_DEFAULT_NUM_INVALID_MSGS_ALLOWED, then the VF is
marked as disabled. In either case, a dev_info message is printed
stating that a VF opcode failed.
This logic originates from the early implementation of VF support in
commit 5c3c48ac6b ("i40e: implement virtual device interface").
That commit did not go far enough. The "logic" for this behavior seems
to be that error responses somehow indicate a malicious VF. This is not
really true. The PF might be sending an error for any number of reasons
such as lacking resources, an unsupported operation, etc. This does not
indicate a malicious VF. We already have a separate robust malicious VF
detection which relies on hardware logic to detect and prevent a variety
of behaviors.
There is no justification for this behavior in the original
implementation. In fact, a later commit 18b7af57d9 ("i40e: Lower some
message levels") reduced the opcode failure message from a dev_err to a
dev_info. In addition, recent commit 01cbf50877 ("i40e: Fix to not
show opcode msg on unsuccessful VF MAC change") changed the logic to
allow quieting it for expected failures.
That commit prevented this logic from kicking in for specific
circumstances. This change did not go far enough. The behavior is not
documented nor is it part of any requirement for our products. Other
operating systems such as the FreeBSD implementation of our driver do
not include this logic.
It is clear this check does not make sense, and causes problems which
led to ugly workarounds.
Fix this by just removing the entire logic and the need for the
i40e_vc_send_msg_to_vf_ex function.
Fixes: 01cbf50877 ("i40e: Fix to not show opcode msg on unsuccessful VF MAC change")
Fixes: 5c3c48ac6b ("i40e: implement virtual device interface")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f6edb6bcb ]
Requesting quad mode for the FMC resulted in an error:
&fmc {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fwqspi_default>'
[ 0.742963] aspeed-g6-pinctrl 1e6e2000.syscon:pinctrl: invalid function FWQSPID in map table

This is because the quad mode pins are a group of pins, not a function.
After applying this patch we can request the pins and the QSPI data
lines are muxed:
# cat /sys/kernel/debug/pinctrl/1e6e2000.syscon\:pinctrl-aspeed-g6-pinctrl/pinmux-pins |grep 1e620000.spi
pin 196 (AE12): device 1e620000.spi function FWSPID group FWQSPID
pin 197 (AF12): device 1e620000.spi function FWSPID group FWQSPID
pin 240 (Y1): device 1e620000.spi function FWSPID group FWQSPID
pin 241 (Y2): device 1e620000.spi function FWSPID group FWQSPID
pin 242 (Y3): device 1e620000.spi function FWSPID group FWQSPID
pin 243 (Y4): device 1e620000.spi function FWSPID group FWQSPID
Fixes: f510f04c8c ("ARM: dts: aspeed: Add AST2600 pinmux nodes")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20220304011010.974863-1-joel@jms.id.au
Link: https://lore.kernel.org/r/20220304011010.974863-1-joel@jms.id.au'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9dc0c84ad ]
Clang static analysis reports this issue
qed_sriov.c:4727:19: warning: Assigned value is
garbage or undefined
ivi->max_tx_rate = tx_rate ? tx_rate : link.speed;
^ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
link is only sometimes set by the call to qed_iov_get_link()
qed_iov_get_link fails without setting link or returning
status. So change the decl to return status.
Fixes: 73390ac9d8 ("qed*: support ndo_get_vf_config")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 053c8fdf2c ]
The xfrm{4,6}_beet_gso_segment() functions did not correctly set the
SKB_GSO_IPXIP4 and SKB_GSO_IPXIP6 gso types for the address family
tunneling case. Fix this by setting these gso types.
Fixes: 384a46ea7b ("esp4: add gso_segment for esp4 beet mode")
Fixes: 7f9e40eb18 ("esp6: add gso_segment for esp6 beet mode")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dacc73ed0b ]
Currently the value of max_discard_segment will be set to
MAX_DISCARD_SEGMENTS (256) with no basis in hardware if device
set 0 to max_discard_seg in configuration space. It's incorrect
since the device might not be able to handle such large descriptors.
To fix it, let's follow max_segments restrictions in this case.
Fixes: 1f23816b8e ("virtio_blk: add discard and write zeroes support")
Signed-off-by: Xie Yongji <xieyongji@bytedance.com>
Link: https://lore.kernel.org/r/20220304100058.116-1-xieyongji@bytedance.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c6a502c229 ]
dsp_pipeline_build() allocates dup pointer by kstrdup(cfg),
but then it updates dup variable by strsep(&dup, "|").
As a result when it calls kfree(dup), the dup variable contains NULL.
Found by Linux Driver Verification project (linuxtesting.org) with SVACE.
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Fixes: 960366cf8d ("Add mISDN DSP")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2682ea324b ]
As Leon Romanovsky's tips:
The definition of macro PIPELINE_DEBUG is commented more than 10 years ago
and can be seen as a dead code that should be removed.
Suggested-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc71d37fd1 ]
The driver creates the top row map sysfs attribute in input_configured()
method; unfortunately we do not have a callback that is executed when HID
interface is unbound, thus we are leaking these sysfs attributes, for
example when device is disconnected.
To fix it let's switch to managed version of adding sysfs attributes which
will ensure that they are destroyed when the driver is unbound.
Fixes: 14c9c014ba ("HID: add vivaldi HID driver")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e7c4d3652 ]
GDSCs have multiple transition delays which are used for the GDSC FSM
states. Older targets/designs required these values to be updated from
gdsc code to certain default values for the FSM state to work as
expected. But on the newer targets/designs the values updated from the
GDSC driver can hamper the FSM state to not work as expected.
On SC7180 we observe black screens because the gdsc is being
enabled/disabled very rapidly and the GDSC FSM state does not work as
expected. This is due to the fact that the GDSC reset value is being
updated from SW.
Thus add support to update the transition delay from the clock
controller gdscs as required.
Fixes: 45dd0e5531 ("clk: qcom: Add support for GDSCs)
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Link: https://lore.kernel.org/r/20220223185606.3941-1-tdas@codeaurora.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 515415d316 ]
While the HVS has the same context memory size in the BCM2711 than in
the previous SoCs, the range allocated to the registers doubled and it
now takes 16k + 16k, compared to 8k + 16k before.
The KMS driver will use the whole context RAM though, eventually
resulting in a pointer dereference error when we access the higher half
of the context memory since it hasn't been mapped.
Fixes: 4564363351 ("ARM: dts: bcm2711: Enable the display pipeline")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 66e3531b33 upstream.
When calling gnttab_end_foreign_access_ref() the returned value must
be tested and the reaction to that value should be appropriate.
In case of failure in xennet_get_responses() the reaction should not be
to crash the system, but to disable the network device.
The calls in setup_netfront() can be replaced by calls of
gnttab_end_foreign_access(). While at it avoid double free of ring
pages and grant references via xennet_disconnect_backend() in this case.
This is CVE-2022-23042 / part of XSA-396.
Reported-by: Demi Marie Obenour <demi@invisiblethingslab.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 42baefac63 upstream.
gnttab_end_foreign_access() is used to free a grant reference and
optionally to free the associated page. In case the grant is still in
use by the other side processing is being deferred. This leads to a
problem in case no page to be freed is specified by the caller: the
caller doesn't know that the page is still mapped by the other side
and thus should not be used for other purposes.
The correct way to handle this situation is to take an additional
reference to the granted page in case handling is being deferred and
to drop that reference when the grant reference could be freed
finally.
This requires that there are no users of gnttab_end_foreign_access()
left directly repurposing the granted page after the call, as this
might result in clobbered data or information leaks via the not yet
freed grant reference.
This is part of CVE-2022-23041 / XSA-396.
Reported-by: Simon Gaiser <simon@invisiblethingslab.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit b0576cc9c6 upstream.
Instead of __get_free_pages() and free_pages() use alloc_pages_exact()
and free_pages_exact(). This is in preparation of a change of
gnttab_end_foreign_access() which will prohibit use of high-order
pages.
This is part of CVE-2022-23041 / XSA-396.
Reported-by: Simon Gaiser <simon@invisiblethingslab.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 5cadd4bb1d upstream.
Instead of __get_free_pages() and free_pages() use alloc_pages_exact()
and free_pages_exact(). This is in preparation of a change of
gnttab_end_foreign_access() which will prohibit use of high-order
pages.
By using the local variable "order" instead of ring->intf->ring_order
in the error path of xen_9pfs_front_alloc_dataring() another bug is
fixed, as the error path can be entered before ring->intf->ring_order
is being set.
By using alloc_pages_exact() the size in bytes is specified for the
allocation, which fixes another bug for the case of
order < (PAGE_SHIFT - XEN_PAGE_SHIFT).
This is part of CVE-2022-23041 / XSA-396.
Reported-by: Simon Gaiser <simon@invisiblethingslab.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 1dbd11ca75 upstream.
Remove gnttab_query_foreign_access(), as it is unused and unsafe to
use.
All previous use cases assumed a grant would not be in use after
gnttab_query_foreign_access() returned 0. This information is useless
in best case, as it only refers to a situation in the past, which could
have changed already.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d3b6372c58 upstream.
Using gnttab_query_foreign_access() is unsafe, as it is racy by design.
The use case in the gntalloc driver is not needed at all. While at it
replace the call of gnttab_end_foreign_access_ref() with a call of
gnttab_end_foreign_access(), which is what is really wanted there. In
case the grant wasn't used due to an allocation failure, just free the
grant via gnttab_free_grant_reference().
This is CVE-2022-23039 / part of XSA-396.
Reported-by: Demi Marie Obenour <demi@invisiblethingslab.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 33172ab50a upstream.
It isn't enough to check whether a grant is still being in use by
calling gnttab_query_foreign_access(), as a mapping could be realized
by the other side just after having called that function.
In case the call was done in preparation of revoking a grant it is
better to do so via gnttab_try_end_foreign_access() and check the
success of that operation instead.
This is CVE-2022-23038 / part of XSA-396.
Reported-by: Demi Marie Obenour <demi@invisiblethingslab.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 31185df7e2 upstream.
It isn't enough to check whether a grant is still being in use by
calling gnttab_query_foreign_access(), as a mapping could be realized
by the other side just after having called that function.
In case the call was done in preparation of revoking a grant it is
better to do so via gnttab_end_foreign_access_ref() and check the
success of that operation instead.
This is CVE-2022-23037 / part of XSA-396.
Reported-by: Demi Marie Obenour <demi@invisiblethingslab.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit abf1fd5919 upstream.
It isn't enough to check whether a grant is still being in use by
calling gnttab_query_foreign_access(), as a mapping could be realized
by the other side just after having called that function.
In case the call was done in preparation of revoking a grant it is
better to do so via gnttab_end_foreign_access_ref() and check the
success of that operation instead.
For the ring allocation use alloc_pages_exact() in order to avoid
high order pages in case of a multi-page ring.
If a grant wasn't unmapped by the backend without persistent grants
being used, set the device state to "error".
This is CVE-2022-23036 / part of XSA-396.
Reported-by: Demi Marie Obenour <demi@invisiblethingslab.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 6b1775f26a upstream.
Add a new grant table function gnttab_try_end_foreign_access(), which
will remove and free a grant if it is not in use.
Its main use case is to either free a grant if it is no longer in use,
or to take some other action if it is still in use. This other action
can be an error exit, or (e.g. in the case of blkfront persistent grant
feature) some special handling.
This is CVE-2022-23036, CVE-2022-23038 / part of XSA-396.
Reported-by: Demi Marie Obenour <demi@invisiblethingslab.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 3777ea7bac upstream.
Letting xenbus_grant_ring() tear down grants in the error case is
problematic, as the other side could already have used these grants.
Calling gnttab_end_foreign_access_ref() without checking success is
resulting in an unclear situation for any caller of xenbus_grant_ring()
as in the error case the memory pages of the ring page might be
partially mapped. Freeing them would risk unwanted foreign access to
them, while not freeing them would leak memory.
In order to remove the need to undo any gnttab_grant_foreign_access()
calls, use gnttab_alloc_grant_references() to make sure no further
error can occur in the loop granting access to the ring pages.
It should be noted that this way of handling removes leaking of
grant entries in the error case, too.
This is CVE-2022-23040 / part of XSA-396.
Reported-by: Demi Marie Obenour <demi@invisiblethingslab.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1a384d2cb upstream.
The kernel test robot discovered that building without
HARDEN_BRANCH_PREDICTOR issues a warning due to a missing
argument to pr_info().
Add the missing argument.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 9dd78194a3 ("ARM: report Spectre v2 status through sysfs")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 36168e387f upstream.
ld.lld does not support the NOCROSSREFS directive at the moment, which
breaks the build after commit b9baf5c8c5 ("ARM: Spectre-BHB
workaround"):
ld.lld: error: ./arch/arm/kernel/vmlinux.lds:34: AT expected, but got NOCROSSREFS
Support for this directive will eventually be implemented, at which
point a version check can be added. To avoid breaking the build in the
meantime, just define NOCROSSREFS to nothing when using ld.lld, with a
link to the issue for tracking.
Cc: stable@vger.kernel.org
Fixes: b9baf5c8c5 ("ARM: Spectre-BHB workaround")
Link: https://github.com/ClangBuiltLinux/linux/issues/1609
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58c9a5060c upstream.
The mitigations for Spectre-BHB are only applied when an exception is
taken from user-space. The mitigation status is reported via the spectre_v2
sysfs vulnerabilities file.
When unprivileged eBPF is enabled the mitigation in the exception vectors
can be avoided by an eBPF program.
When unprivileged eBPF is enabled, print a warning and report vulnerable
via the sysfs vulnerabilities file.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 228a26b912 upstream.
Future CPUs may implement a clearbhb instruction that is sufficient
to mitigate SpectreBHB. CPUs that implement this instruction, but
not CSV2.3 must be affected by Spectre-BHB.
Add support to use this instruction as the BHB mitigation on CPUs
that support it. The instruction is in the hint space, so it will
be treated by a NOP as older CPUs.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
[ modified for stable: Use a KVM vector template instead of alternatives,
removed bitmap of mitigations ]
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5905d6af4 upstream.
KVM allows the guest to discover whether the ARCH_WORKAROUND SMCCC are
implemented, and to preserve that state during migration through its
firmware register interface.
Add the necessary boiler plate for SMCCC_ARCH_WORKAROUND_3.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 558c303c97 upstream.
Speculation attacks against some high-performance processors can
make use of branch history to influence future speculation.
When taking an exception from user-space, a sequence of branches
or a firmware call overwrites or invalidates the branch history.
The sequence of branches is added to the vectors, and should appear
before the first indirect branch. For systems using KPTI the sequence
is added to the kpti trampoline where it has a free register as the exit
from the trampoline is via a 'ret'. For systems not using KPTI, the same
register tricks are used to free up a register in the vectors.
For the firmware call, arch-workaround-3 clobbers 4 registers, so
there is no choice but to save them to the EL1 stack. This only happens
for entry from EL0, so if we take an exception due to the stack access,
it will not become re-entrant.
For KVM, the existing branch-predictor-hardening vectors are used.
When a spectre version of these vectors is in use, the firmware call
is sufficient to mitigate against Spectre-BHB. For the non-spectre
versions, the sequence of branches is added to the indirect vector.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
[ modified for stable, removed bitmap of mitigations, use kvm template
infrastructure ]
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5bdf343760 upstream.
CPUs vulnerable to Spectre-BHB either need to make an SMC-CC firmware
call from the vectors, or run a sequence of branches. This gets added
to the hyp vectors. If there is no support for arch-workaround-1 in
firmware, the indirect vector will be used.
kvm_init_vector_slots() only initialises the two indirect slots if
the platform is vulnerable to Spectre-v3a. pKVM's hyp_map_vectors()
only initialises __hyp_bp_vect_base if the platform is vulnerable to
Spectre-v3a.
As there are about to more users of the indirect vectors, ensure
their entries in hyp_spectre_vector_selector[] are always initialised,
and __hyp_bp_vect_base defaults to the regular VA mapping.
The Spectre-v3a check is moved to a helper
kvm_system_needs_idmapped_vectors(), and merged with the code
that creates the hyp mappings.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dee435be76 upstream.
Speculation attacks against some high-performance processors can
make use of branch history to influence future speculation as part of
a spectre-v2 attack. This is not mitigated by CSV2, meaning CPUs that
previously reported 'Not affected' are now moderately mitigated by CSV2.
Update the value in /sys/devices/system/cpu/vulnerabilities/spectre_v2
to also show the state of the BHB mitigation.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd09128d16 upstream.
The Spectre-BHB workaround adds a firmware call to the vectors. This
is needed on some CPUs, but not others. To avoid the unaffected CPU in
a big/little pair from making the firmware call, create per cpu vectors.
The per-cpu vectors only apply when returning from EL0.
Systems using KPTI can use the canonical 'full-fat' vectors directly at
EL1, the trampoline exit code will switch to this_cpu_vector on exit to
EL0. Systems not using KPTI should always use this_cpu_vector.
this_cpu_vector will point at a vector in tramp_vecs or
__bp_harden_el1_vectors, depending on whether KPTI is in use.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b28a8eebe8 upstream.
The trampoline code needs to use the address of symbols in the wider
kernel, e.g. vectors. PC-relative addressing wouldn't work as the
trampoline code doesn't run at the address the linker expected.
tramp_ventry uses a literal pool, unless CONFIG_RANDOMIZE_BASE is
set, in which case it uses the data page as a literal pool because
the data page can be unmapped when running in user-space, which is
required for CPUs vulnerable to meltdown.
Pull this logic out as a macro, instead of adding a third copy
of it.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba2689234b upstream.
Some CPUs affected by Spectre-BHB need a sequence of branches, or a
firmware call to be run before any indirect branch. This needs to go
in the vectors. No CPU needs both.
While this can be patched in, it would run on all CPUs as there is a
single set of vectors. If only one part of a big/little combination is
affected, the unaffected CPUs have to run the mitigation too.
Create extra vectors that include the sequence. Subsequent patches will
allow affected CPUs to select this set of vectors. Later patches will
modify the loop count to match what the CPU requires.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aff65393fa upstream.
kpti is an optional feature, for systems not using kpti a set of
vectors for the spectre-bhb mitigations is needed.
Add another set of vectors, __bp_harden_el1_vectors, that will be
used if a mitigation is needed and kpti is not in use.
The EL1 ventries are repeated verbatim as there is no additional
work needed for entry from EL1.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a9c406e646 upstream.
Adding a second set of vectors to .entry.tramp.text will make it
larger than a single 4K page.
Allow the trampoline text to occupy up to three pages by adding two
more fixmap slots. Previous changes to tramp_valias allowed it to reach
beyond a single page.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c47e4d04ba upstream.
Spectre-BHB needs to add sequences to the vectors. Having one global
set of vectors is a problem for big/little systems where the sequence
is costly on cpus that are not vulnerable.
Making the vectors per-cpu in the style of KVM's bh_harden_hyp_vecs
requires the vectors to be generated by macros.
Make the kpti re-mapping of the kernel optional, so the macros can be
used without kpti.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13d7a08352 upstream.
The macros for building the kpti trampoline are all behind
CONFIG_UNMAP_KERNEL_AT_EL0, and in a region that outputs to the
.entry.tramp.text section.
Move the macros out so they can be used to generate other kinds of
trampoline. Only the symbols need to be guarded by
CONFIG_UNMAP_KERNEL_AT_EL0 and appear in the .entry.tramp.text section.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed50da7764 upstream.
The tramp_ventry macro uses tramp_vectors as the address of the vectors
when calculating which ventry in the 'full fat' vectors to branch to.
While there is one set of tramp_vectors, this will be true.
Adding multiple sets of vectors will break this assumption.
Move the generation of the vectors to a macro, and pass the start
of the vectors as an argument to tramp_ventry.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c5bf79b69 upstream.
Systems using kpti enter and exit the kernel through a trampoline mapping
that is always mapped, even when the kernel is not. tramp_valias is a macro
to find the address of a symbol in the trampoline mapping.
Adding extra sets of vectors will expand the size of the entry.tramp.text
section to beyond 4K. tramp_valias will be unable to generate addresses
for symbols beyond 4K as it uses the 12 bit immediate of the add
instruction.
As there are now two registers available when tramp_alias is called,
use the extra register to avoid the 4K limit of the 12 bit immediate.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c091fb6ae0 upstream.
The trampoline code has a data page that holds the address of the vectors,
which is unmapped when running in user-space. This ensures that with
CONFIG_RANDOMIZE_BASE, the randomised address of the kernel can't be
discovered until after the kernel has been mapped.
If the trampoline text page is extended to include multiple sets of
vectors, it will be larger than a single page, making it tricky to
find the data page without knowing the size of the trampoline text
pages, which will vary with PAGE_SIZE.
Move the data page to appear before the text page. This allows the
data page to be found without knowing the size of the trampoline text
pages. 'tramp_vectors' is used to refer to the beginning of the
.entry.tramp.text section, do that explicitly.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 03aff3a77a upstream.
Kpti stashes x30 in far_el1 while it uses x30 for all its work.
Making the vectors a per-cpu data structure will require a second
register.
Allow tramp_exit two registers before it unmaps the kernel, by
leaving x30 on the stack, and stashing x29 in far_el1.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d739da1694 upstream.
Subsequent patches will add additional sets of vectors that use
the same tricks as the kpti vectors to reach the full-fat vectors.
The full-fat vectors contain some cleanup for kpti that is patched
in by alternatives when kpti is in use. Once there are additional
vectors, the cleanup will be needed in more cases.
But on big/little systems, the cleanup would be harmful if no
trampoline vector were in use. Instead of forcing CPUs that don't
need a trampoline vector to use one, make the trampoline cleanup
optional.
Entry at the top of the vectors will skip the cleanup. The trampoline
vectors can then skip the first instruction, triggering the cleanup
to run.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b33d4860d upstream.
The spectre-v4 sequence includes an SMC from the assembly entry code.
spectre_v4_patch_fw_mitigation_conduit is the patching callback that
generates an HVC or SMC depending on the SMCCC conduit type.
As this isn't specific to spectre-v4, rename it
smccc_patch_fw_mitigation_conduit so it can be re-used.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 11ecdad722 upstream.
The implementor will be used to condition the FIQ support quirk.
The specific CPU types are not used at the moment, but let's add them
for documentation purposes.
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 25875aa71d upstream.
The mitigations for Spectre-BHB are only applied when an exception
is taken, but when unprivileged BPF is enabled, userspace can
load BPF programs that can be used to exploit the problem.
When unprivileged BPF is enabled, report the vulnerable status via
the spectre_v2 sysfs file.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b9baf5c8c5 upstream.
Workaround the Spectre BHB issues for Cortex-A15, Cortex-A57,
Cortex-A72, Cortex-A73 and Cortex-A75. We also include Brahma B15 as
well to be safe, which is affected by Spectre V2 in the same ways as
Cortex-A15.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
[changes due to lack of SYSTEM_FREEING_INITMEM - gregkh]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0de05d056a upstream.
The commit
44a3918c82 ("x86/speculation: Include unprivileged eBPF status in Spectre v2 mitigation reporting")
added a warning for the "eIBRS + unprivileged eBPF" combination, which
has been shown to be vulnerable against Spectre v2 BHB-based attacks.
However, there's no warning about the "eIBRS + LFENCE retpoline +
unprivileged eBPF" combo. The LFENCE adds more protection by shortening
the speculation window after a mispredicted branch. That makes an attack
significantly more difficult, even with unprivileged eBPF. So at least
for now the logic doesn't warn about that combination.
But if you then add SMT into the mix, the SMT attack angle weakens the
effectiveness of the LFENCE considerably.
So extend the "eIBRS + unprivileged eBPF" warning to also include the
"eIBRS + LFENCE + unprivileged eBPF + SMT" case.
[ bp: Massage commit message. ]
Suggested-by: Alyssa Milburn <alyssa.milburn@linux.intel.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eafd987d4a upstream.
With:
f8a66d608a ("x86,bugs: Unconditionally allow spectre_v2=retpoline,amd")
it became possible to enable the LFENCE "retpoline" on Intel. However,
Intel doesn't recommend it, as it has some weaknesses compared to
retpoline.
Now AMD doesn't recommend it either.
It can still be left available as a cmdline option. It's faster than
retpoline but is weaker in certain scenarios -- particularly SMT, but
even non-SMT may be vulnerable in some cases.
So just unconditionally warn if the user requests it on the cmdline.
[ bp: Massage commit message. ]
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9b6013a7c upstream.
Update the link to the "Software Techniques for Managing Speculation
on AMD Processors" whitepaper.
Signed-off-by: Kim Phillips <kim.phillips@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 244d00b5dd upstream.
AMD retpoline may be susceptible to speculation. The speculation
execution window for an incorrect indirect branch prediction using
LFENCE/JMP sequence may potentially be large enough to allow
exploitation using Spectre V2.
By default, don't use retpoline,lfence on AMD. Instead, use the
generic retpoline.
Signed-off-by: Kim Phillips <kim.phillips@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 44a3918c82 upstream.
With unprivileged eBPF enabled, eIBRS (without retpoline) is vulnerable
to Spectre v2 BHB-based attacks.
When both are enabled, print a warning message and report it in the
'spectre_v2' sysfs vulnerabilities file.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
[fllinden@amazon.com: backported to 5.10]
Signed-off-by: Frank van der Linden <fllinden@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ad3eb1132 upstream.
Update the doc with the new fun.
[ bp: Massage commit message. ]
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
[fllinden@amazon.com: backported to 5.10]
Signed-off-by: Frank van der Linden <fllinden@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e19da8522 upstream.
Thanks to the chaps at VUsec it is now clear that eIBRS is not
sufficient, therefore allow enabling of retpolines along with eIBRS.
Add spectre_v2=eibrs, spectre_v2=eibrs,lfence and
spectre_v2=eibrs,retpoline options to explicitly pick your preferred
means of mitigation.
Since there's new mitigations there's also user visible changes in
/sys/devices/system/cpu/vulnerabilities/spectre_v2 to reflect these
new mitigations.
[ bp: Massage commit message, trim error messages,
do more precise eIBRS mode checking. ]
Co-developed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Patrick Colp <patrick.colp@oracle.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d45476d983 upstream.
The RETPOLINE_AMD name is unfortunate since it isn't necessarily
AMD only, in fact Hygon also uses it. Furthermore it will likely be
sufficient for some Intel processors. Therefore rename the thing to
RETPOLINE_LFENCE to better describe what it is.
Add the spectre_v2=retpoline,lfence option as an alias to
spectre_v2=retpoline,amd to preserve existing setups. However, the output
of /sys/devices/system/cpu/vulnerabilities/spectre_v2 will be changed.
[ bp: Fix typos, massage. ]
Co-developed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
[fllinden@amazon.com: backported to 5.10]
Signed-off-by: Frank van der Linden <fllinden@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6d95c5a62 upstream.
This reverts commit b515d26372.
Commit b515d26372 ("xfrm: xfrm_state_mtu
should return at least 1280 for ipv6") in v5.14 breaks the TCP MSS
calculation in ipsec transport mode, resulting complete stalls of TCP
connections. This happens when the (P)MTU is 1280 or slighly larger.
The desired formula for the MSS is:
MSS = (MTU - ESP_overhead) - IP header - TCP header
However, the above commit clamps the (MTU - ESP_overhead) to a
minimum of 1280, turning the formula into
MSS = max(MTU - ESP overhead, 1280) - IP header - TCP header
With the (P)MTU near 1280, the calculated MSS is too large and the
resulting TCP packets never make it to the destination because they
are over the actual PMTU.
The above commit also causes suboptimal double fragmentation in
xfrm tunnel mode, as described in
https://lore.kernel.org/netdev/20210429202529.codhwpc7w6kbudug@dwarf.suse.cz/
The original problem the above commit was trying to fix is now fixed
by commit 6596a02295 ("xfrm: fix MTU
regression").
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4751dc9962 upstream.
During log replay, whenever we need to check if a name (dentry) exists in
a directory we do searches on the subvolume tree for inode references or
or directory entries (BTRFS_DIR_INDEX_KEY keys, and BTRFS_DIR_ITEM_KEY
keys as well, before kernel 5.17). However when during log replay we
unlink a name, through btrfs_unlink_inode(), we may not delete inode
references and dir index keys from a subvolume tree and instead just add
the deletions to the delayed inode's delayed items, which will only be
run when we commit the transaction used for log replay. This means that
after an unlink operation during log replay, if we attempt to search for
the same name during log replay, we will not see that the name was already
deleted, since the deletion is recorded only on the delayed items.
We run delayed items after every unlink operation during log replay,
except at unlink_old_inode_refs() and at add_inode_ref(). This was due
to an overlook, as delayed items should be run after evert unlink, for
the reasons stated above.
So fix those two cases.
Fixes: 0d836392ca ("Btrfs: fix mount failure after fsync due to hard link recreation")
Fixes: 1f250e929a ("Btrfs: fix log replay failure after unlink and link combination")
CC: stable@vger.kernel.org # 4.19+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d4aef1e122 upstream.
The commit e804861bd4 ("btrfs: fix deadlock between quota disable and
qgroup rescan worker") by Kawasaki resolves deadlock between quota
disable and qgroup rescan worker. But also there is a deadlock case like
it. It's about enabling or disabling quota and creating or removing
qgroup. It can be reproduced in simple script below.
for i in {1..100}
do
btrfs quota enable /mnt &
btrfs qgroup create 1/0 /mnt &
btrfs qgroup destroy 1/0 /mnt &
btrfs quota disable /mnt &
done
Here's why the deadlock happens:
1) The quota rescan task is running.
2) Task A calls btrfs_quota_disable(), locks the qgroup_ioctl_lock
mutex, and then calls btrfs_qgroup_wait_for_completion(), to wait for
the quota rescan task to complete.
3) Task B calls btrfs_remove_qgroup() and it blocks when trying to lock
the qgroup_ioctl_lock mutex, because it's being held by task A. At that
point task B is holding a transaction handle for the current transaction.
4) The quota rescan task calls btrfs_commit_transaction(). This results
in it waiting for all other tasks to release their handles on the
transaction, but task B is blocked on the qgroup_ioctl_lock mutex
while holding a handle on the transaction, and that mutex is being held
by task A, which is waiting for the quota rescan task to complete,
resulting in a deadlock between these 3 tasks.
To resolve this issue, the thread disabling quota should unlock
qgroup_ioctl_lock before waiting rescan completion. Move
btrfs_qgroup_wait_for_completion() after unlock of qgroup_ioctl_lock.
Fixes: e804861bd4 ("btrfs: fix deadlock between quota disable and qgroup rescan worker")
CC: stable@vger.kernel.org # 5.4+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Signed-off-by: Sidong Yang <realwakka@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d994788743 upstream.
When doing a full fsync, if we have prealloc extents beyond (or at) eof,
and the leaves that contain them were not modified in the current
transaction, we end up not logging them. This results in losing those
extents when we replay the log after a power failure, since the inode is
truncated to the current value of the logged i_size.
Just like for the fast fsync path, we need to always log all prealloc
extents starting at or beyond i_size. The fast fsync case was fixed in
commit 471d557afe ("Btrfs: fix loss of prealloc extents past i_size
after fsync log replay") but it missed the full fsync path. The problem
exists since the very early days, when the log tree was added by
commit e02119d5a7 ("Btrfs: Add a write ahead tree log to optimize
synchronous operations").
Example reproducer:
$ mkfs.btrfs -f /dev/sdc
$ mount /dev/sdc /mnt
# Create our test file with many file extent items, so that they span
# several leaves of metadata, even if the node/page size is 64K. Use
# direct IO and not fsync/O_SYNC because it's both faster and it avoids
# clearing the full sync flag from the inode - we want the fsync below
# to trigger the slow full sync code path.
$ xfs_io -f -d -c "pwrite -b 4K 0 16M" /mnt/foo
# Now add two preallocated extents to our file without extending the
# file's size. One right at i_size, and another further beyond, leaving
# a gap between the two prealloc extents.
$ xfs_io -c "falloc -k 16M 1M" /mnt/foo
$ xfs_io -c "falloc -k 20M 1M" /mnt/foo
# Make sure everything is durably persisted and the transaction is
# committed. This makes all created extents to have a generation lower
# than the generation of the transaction used by the next write and
# fsync.
sync
# Now overwrite only the first extent, which will result in modifying
# only the first leaf of metadata for our inode. Then fsync it. This
# fsync will use the slow code path (inode full sync bit is set) because
# it's the first fsync since the inode was created/loaded.
$ xfs_io -c "pwrite 0 4K" -c "fsync" /mnt/foo
# Extent list before power failure.
$ xfs_io -c "fiemap -v" /mnt/foo
/mnt/foo:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [0..7]: 2178048..2178055 8 0x0
1: [8..16383]: 26632..43007 16376 0x0
2: [16384..32767]: 2156544..2172927 16384 0x0
3: [32768..34815]: 2172928..2174975 2048 0x800
4: [34816..40959]: hole 6144
5: [40960..43007]: 2174976..2177023 2048 0x801
<power fail>
# Mount fs again, trigger log replay.
$ mount /dev/sdc /mnt
# Extent list after power failure and log replay.
$ xfs_io -c "fiemap -v" /mnt/foo
/mnt/foo:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [0..7]: 2178048..2178055 8 0x0
1: [8..16383]: 26632..43007 16376 0x0
2: [16384..32767]: 2156544..2172927 16384 0x1
# The prealloc extents at file offsets 16M and 20M are missing.
So fix this by calling btrfs_log_prealloc_extents() when we are doing a
full fsync, so that we always log all prealloc extents beyond eof.
A test case for fstests will follow soon.
CC: stable@vger.kernel.org # 4.19+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d02b444b8 upstream.
__setup() handlers should generally return 1 to indicate that the
boot options have been handled.
Using invalid option values causes the entire kernel boot option
string to be reported as Unknown and added to init's environment
strings, polluting it.
Unknown kernel command line parameters "BOOT_IMAGE=/boot/bzImage-517rc6
kprobe_event=p,syscall_any,$arg1 trace_options=quiet
trace_clock=jiffies", will be passed to user space.
Run /sbin/init as init process
with arguments:
/sbin/init
with environment:
HOME=/
TERM=linux
BOOT_IMAGE=/boot/bzImage-517rc6
kprobe_event=p,syscall_any,$arg1
trace_options=quiet
trace_clock=jiffies
Return 1 from the __setup() handlers so that init's environment is not
polluted with kernel boot options.
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru
Link: https://lkml.kernel.org/r/20220303031744.32356-1-rdunlap@infradead.org
Cc: stable@vger.kernel.org
Fixes: 7bcfaf54f5 ("tracing: Add trace_options kernel command line parameter")
Fixes: e1e232ca6b ("tracing: Add trace_clock=<clock> kernel parameter")
Fixes: 970988e19e ("tracing/kprobe: Add kprobe_event= boot parameter")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d1898f656 upstream.
When trying to add a histogram against an event with the "cpu" field, it
was impossible due to "cpu" being a keyword to key off of the running CPU.
So to fix this, it was changed to "common_cpu" to match the other generic
fields (like "common_pid"). But since some scripts used "cpu" for keying
off of the CPU (for events that did not have "cpu" as a field, which is
most of them), a backward compatibility trick was added such that if "cpu"
was used as a key, and the event did not have "cpu" as a field name, then
it would fallback and switch over to "common_cpu".
This fix has a couple of subtle bugs. One was that when switching over to
"common_cpu", it did not change the field name, it just set a flag. But
the code still found a "cpu" field. The "cpu" field is used for filtering
and is returned when the event does not have a "cpu" field.
This was found by:
# cd /sys/kernel/tracing
# echo hist:key=cpu,pid:sort=cpu > events/sched/sched_wakeup/trigger
# cat events/sched/sched_wakeup/hist
Which showed the histogram unsorted:
{ cpu: 19, pid: 1175 } hitcount: 1
{ cpu: 6, pid: 239 } hitcount: 2
{ cpu: 23, pid: 1186 } hitcount: 14
{ cpu: 12, pid: 249 } hitcount: 2
{ cpu: 3, pid: 994 } hitcount: 5
Instead of hard coding the "cpu" checks, take advantage of the fact that
trace_event_field_field() returns a special field for "cpu" and "CPU" if
the event does not have "cpu" as a field. This special field has the
"filter_type" of "FILTER_CPU". Check that to test if the returned field is
of the CPU type instead of doing the string compare.
Also, fix the sorting bug by testing for the hist_field flag of
HIST_FIELD_FL_CPU when setting up the sort routine. Otherwise it will use
the special CPU field to know what compare routine to use, and since that
special field does not have a size, it returns tracing_map_cmp_none.
Cc: stable@vger.kernel.org
Fixes: 1e3bac71c5 ("tracing/histogram: Rename "cpu" to "common_cpu"")
Reported-by: Daniel Bristot de Oliveira <bristot@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04b7762e37 upstream.
Before these changes elan_suspend() would only disable the regulator
when device_may_wakeup() returns false; whereas elan_resume() would
unconditionally enable it, leading to an enable count imbalance when
device_may_wakeup() returns true.
This triggers the "WARN_ON(regulator->enable_count)" in regulator_put()
when the elan_i2c driver gets unbound, this happens e.g. with the
hot-plugable dock with Elan I2C touchpad for the Asus TF103C 2-in-1.
Fix this by making the regulator_enable() call also be conditional
on device_may_wakeup() returning false.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220131135436.29638-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81a36d8ce5 upstream.
elan_disable_power() is called conditionally on suspend, where as
elan_enable_power() is always called on resume. This leads to
an imbalance in the regulator's enable count.
Move the regulator_[en|dis]able() calls out of elan_[en|dis]able_power()
in preparation of fixing this.
No functional changes intended.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220131135436.29638-1-hdegoede@redhat.com
[dtor: consolidate elan_[en|dis]able() into elan_set_power()]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 10b6bb62ae ]
Ido Schimmel points out that since commit 52cff74eef ("dcbnl : Disable
software interrupts before taking dcb_lock"), the DCB API can be called
by drivers from softirq context.
One such in-tree example is the chelsio cxgb4 driver:
dcb_rpl
-> cxgb4_dcb_handle_fw_update
-> dcb_ieee_setapp
If the firmware for this driver happened to send an event which resulted
in a call to dcb_ieee_setapp() at the exact same time as another
DCB-enabled interface was unregistering on the same CPU, the softirq
would deadlock, because the interrupted process was already holding the
dcb_lock in dcbnl_flush_dev().
Fix this unlikely event by using spin_lock_bh() in dcbnl_flush_dev() as
in the rest of the dcbnl code.
Fixes: 91b0383fef ("net: dcb: flush lingering app table entries for unregistered devices")
Reported-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220302193939.1368823-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45eebd6299 ]
Replace state changes of iavf state machine
with a method that also tracks the previous
state the machine was on.
This change is required for further work with
refactoring init and watchdog state machines.
Tracking of previous state would help us
recover iavf after failure has occurred.
Signed-off-by: Jakub Pawlak <jakub.pawlak@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 767b9825ed ]
The function pci_find_capability() in t3_prep_adapter() can fail, so its
return value should be checked.
Fixes: 4d22de3e6c ("Add support for the latest 1G/10G Chelsio adapter, T3")
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36491f2df9 ]
If we get a transport event, set the error and mark the init as
complete so the attempt to send crq-init or login fail sooner
rather than wait for the timeout.
Fixes: bbd669a868 ("ibmvnic: Fix completion structure initialization")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d3b01e0d4 ]
Move the eDP panel on Venice 2 and Nyan boards into the corresponding
AUX bus device tree node. This allows us to avoid a nasty circular
dependency that would otherwise be created between the DPAUX and panel
nodes via the DDC/I2C phandle.
Fixes: eb481f9ac9 ("ARM: tegra: add Acer Chromebook 13 device tree")
Fixes: 59fe02cb07 ("ARM: tegra: Add DTS for the nyan-blaze board")
Fixes: 40e231c770 ("ARM: tegra: Enable eDP for Venice2")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a222fd8541 ]
As the possible failure of the ioremap(), the par_io could be NULL.
Therefore it should be better to check it and return error in order to
guarantee the success of the initiation.
But, I also notice that all the caller like mpc85xx_qe_par_io_init() in
`arch/powerpc/platforms/85xx/common.c` don't check the return value of
the par_io_init().
Actually, par_io_init() needs to check to handle the potential error.
I will submit another patch to fix that.
Anyway, par_io_init() itsely should be fixed.
Fixes: 7aa1aa6ece ("QE: Move QE from arch/powerpc to drivers/soc")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b9abe942cd ]
If 'devm_kstrdup()' fails, we should return -ENOMEM.
While at it, move the 'of_node_put()' call in the error handling path and
after the 'machine' has been copied.
Better safe than sorry.
Fixes: a6fc3b6981 ("soc: fsl: add GUTS driver for QorIQ platforms")
Depends-on: fddacc7ff4dd ("soc: fsl: guts: Revert commit 3c0d64e867ed")
Suggested-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8840f5460a ]
Devkit8000 board seems to always used 32k_counter as clocksource.
Restore this behavior.
If clocksource is back to 32k_counter, timer12 is now the clockevent
source (as before) and timer2 is not longer needed here.
This commit fixes the same issue observed with commit 23885389db
("ARM: dts: Fix timer regression for beagleboard revision c") when sleep
is blocked until hitting keys over serial console.
Fixes: aba1ad05da ("clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support")
Fixes: e428e250fd ("ARM: dts: Configure system timers for omap3")
Signed-off-by: Anthoine Bourgeois <anthoine.bourgeois@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c194dad210 upstream.
s390 has a swap_ex_entry_fixup function, however it is not being used
since common code expects a swap_ex_entry_fixup define. If it is not
defined the default implementation will be used. So fix this by adding
a proper define.
However also the implementation of the function must be fixed, since a
NULL value for handler has a special meaning and must not be adjusted.
Luckily all of this doesn't fix a real bug currently: the main extable
is correctly sorted during build time, and for runtime sorting there
is currently no case where the handler field is not NULL.
Fixes: 05a68e892e ("s390/kernel: expand exception table logic to allow new handling options")
Acked-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f2b277c4d1 upstream.
Wangyong reports: after enabling tmpfs filesystem to support transparent
hugepage with the following command:
echo always > /sys/kernel/mm/transparent_hugepage/shmem_enabled
the docker program tries to add F_SEAL_WRITE through the following
command, but it fails unexpectedly with errno EBUSY:
fcntl(5, F_ADD_SEALS, F_SEAL_WRITE) = -1.
That is because memfd_tag_pins() and memfd_wait_for_pins() were never
updated for shmem huge pages: checking page_mapcount() against
page_count() is hopeless on THP subpages - they need to check
total_mapcount() against page_count() on THP heads only.
Make memfd_tag_pins() (compared > 1) as strict as memfd_wait_for_pins()
(compared != 1): either can be justified, but given the non-atomic
total_mapcount() calculation, it is better now to be strict. Bear in
mind that total_mapcount() itself scans all of the THP subpages, when
choosing to take an XA_CHECK_SCHED latency break.
Also fix the unlikely xa_is_value() case in memfd_wait_for_pins(): if a
page has been swapped out since memfd_tag_pins(), then its refcount must
have fallen, and so it can safely be untagged.
Link: https://lkml.kernel.org/r/a4f79248-df75-2c8c-3df-ba3317ccb5da@google.com
Signed-off-by: Hugh Dickins <hughd@google.com>
Reported-by: Zeal Robot <zealci@zte.com.cn>
Reported-by: wangyong <wang.yong12@zte.com.cn>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: CGEL ZTE <cgel.zte@gmail.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Song Liu <songliubraving@fb.com>
Cc: Yang Yang <yang.yang29@zte.com.cn>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c4208653a3 upstream.
Similar to "igc_read_phy_reg_gpy: drop premature return" patch.
igc_write_phy_reg_gpy checks the return value from igc_write_phy_reg_mdic
and if it's not 0, returns immediately. By doing this, it leaves the HW
semaphore in the acquired state.
Drop this premature return statement, the function returns after
releasing the semaphore immediately anyway.
Fixes: 5586838fe9 ("igc: Add code for PHY support")
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Reported-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bac129dbc6 upstream.
This driver, like several others, uses a chained IRQ for each GPIO bank,
and forwards .irq_set_wake to the GPIO bank's upstream IRQ. As a result,
a call to irq_set_irq_wake() needs to lock both the upstream and
downstream irq_desc's. Lockdep considers this to be a possible deadlock
when the irq_desc's share lockdep classes, which they do by default:
============================================
WARNING: possible recursive locking detected
5.17.0-rc3-00394-gc849047c2473 #1 Not tainted
--------------------------------------------
init/307 is trying to acquire lock:
c2dfe27c (&irq_desc_lock_class){-.-.}-{2:2}, at: __irq_get_desc_lock+0x58/0xa0
but task is already holding lock:
c3c0ac7c (&irq_desc_lock_class){-.-.}-{2:2}, at: __irq_get_desc_lock+0x58/0xa0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&irq_desc_lock_class);
lock(&irq_desc_lock_class);
*** DEADLOCK ***
May be due to missing lock nesting notation
4 locks held by init/307:
#0: c1f29f18 (system_transition_mutex){+.+.}-{3:3}, at: __do_sys_reboot+0x90/0x23c
#1: c20f7760 (&dev->mutex){....}-{3:3}, at: device_shutdown+0xf4/0x224
#2: c2e804d8 (&dev->mutex){....}-{3:3}, at: device_shutdown+0x104/0x224
#3: c3c0ac7c (&irq_desc_lock_class){-.-.}-{2:2}, at: __irq_get_desc_lock+0x58/0xa0
stack backtrace:
CPU: 0 PID: 307 Comm: init Not tainted 5.17.0-rc3-00394-gc849047c2473 #1
Hardware name: Allwinner sun8i Family
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x68/0x90
dump_stack_lvl from __lock_acquire+0x1680/0x31a0
__lock_acquire from lock_acquire+0x148/0x3dc
lock_acquire from _raw_spin_lock_irqsave+0x50/0x6c
_raw_spin_lock_irqsave from __irq_get_desc_lock+0x58/0xa0
__irq_get_desc_lock from irq_set_irq_wake+0x2c/0x19c
irq_set_irq_wake from irq_set_irq_wake+0x13c/0x19c
[tail call from sunxi_pinctrl_irq_set_wake]
irq_set_irq_wake from gpio_keys_suspend+0x80/0x1a4
gpio_keys_suspend from gpio_keys_shutdown+0x10/0x2c
gpio_keys_shutdown from device_shutdown+0x180/0x224
device_shutdown from __do_sys_reboot+0x134/0x23c
__do_sys_reboot from ret_fast_syscall+0x0/0x1c
However, this can never deadlock because the upstream and downstream
IRQs are never the same (nor do they even involve the same irqchip).
Silence this erroneous lockdep splat by applying what appears to be the
usual fix of moving the GPIO IRQs to separate lockdep classes.
Fixes: a59c99d9ea ("pinctrl: sunxi: Forward calls to irq_set_irq_wake")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220216040037.22730-1-samuel@sholland.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc97520753 upstream.
The test adds tc filters and checks how many of them were offloaded by
grepping for 'in_hw'.
iproute2 commit f4cd4f127047 ("tc: add skip_hw and skip_sw to control
action offload") added offload indication to tc actions, producing the
following output:
$ tc filter show dev swp2 ingress
...
filter protocol ipv6 pref 1000 flower chain 0 handle 0x7c0
eth_type ipv6
dst_ip 2001:db8:1::7bf
skip_sw
in_hw in_hw_count 1
action order 1: police 0x7c0 rate 10Mbit burst 100Kb mtu 2Kb action drop overhead 0b
ref 1 bind 1
not_in_hw
used_hw_stats immediate
The current grep expression matches on both 'in_hw' and 'not_in_hw',
resulting in incorrect results.
Fix that by using JSON output instead.
Fixes: 5061e77326 ("selftests: mlxsw: Add scale test for tc-police")
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b83299e5b upstream.
early_param() handlers should return 0 on success.
__setup() handlers should return 1 on success, i.e., the parameter
has been handled. A return of 0 would cause the "option=value" string
to be added to init's environment strings, polluting it.
../arch/arm/mm/mmu.c: In function 'test_early_cachepolicy':
../arch/arm/mm/mmu.c:215:1: error: no return statement in function returning non-void [-Werror=return-type]
../arch/arm/mm/mmu.c: In function 'test_noalign_setup':
../arch/arm/mm/mmu.c:221:1: error: no return statement in function returning non-void [-Werror=return-type]
Fixes: b849a60e09 ("ARM: make cr_alignment read-only #ifndef CONFIG_CPU_CP15")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: patches@armlinux.org.uk
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d920eaa4c4 upstream.
The kgdb code needs to register an undef hook for the Thumb UDF
instruction that will fault in order to be functional on Thumb2
platforms.
Reported-by: Johannes Stezenbach <js@sig21.net>
Tested-by: Johannes Stezenbach <js@sig21.net>
Fixes: 5cbad0ebf4 ("kgdb: support for ARCH=arm")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fda2635466 upstream.
igc_read_phy_reg_gpy checks the return value from igc_read_phy_reg_mdic
and if it's not 0, returns immediately. By doing this, it leaves the HW
semaphore in the acquired state.
Drop this premature return statement, the function returns after
releasing the semaphore immediately anyway.
Fixes: 5586838fe9 ("igc: Add code for PHY support")
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c5487b9cde upstream.
Currently, the following error messages are seen during boot:
asoc-simple-card sound: control 2:0:0:SPDIF Switch:0 is already present
cs4265 1-004f: ASoC: failed to add widget SPDIF dapm kcontrol SPDIF Switch: -16
Quoting Mark Brown:
"The driver is just plain buggy, it defines both a regular SPIDF Switch
control and a SND_SOC_DAPM_SWITCH() called SPDIF both of which will
create an identically named control, it can never have loaded without
error. One or both of those has to be renamed or they need to be
merged into one thing."
Fix the duplicated control name by combining the two SPDIF controls here
and move the register bits onto the DAPM widget and have DAPM control them.
Fixes: f853d6b3ba ("ASoC: cs4265: Add a S/PDIF enable switch")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220215120514.1760628-1-festevam@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 258dd90202 upstream.
When the "block" flag is false, the old code would sometimes still call
check_var_size(), which wrongly tells ->query_variable_store() that it can
block.
As far as I can tell, this can't really materialize as a bug at the moment,
because ->query_variable_store only does something on X86 with generic EFI,
and in that configuration we always take the efivar_entry_set_nonblocking()
path.
Fixes: ca0e30dcaa ("efi: Add nonblocking option to efi_query_variable_store()")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20220218180559.1432559-1-jannh@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c7273a266 upstream.
Commit c685c69fba ("ixgbe: don't do any AF_XDP zero-copy transmit if
netif is not OK") addressed the ring transient state when
MEM_TYPE_XSK_BUFF_POOL was being configured which in turn caused the
interface to through down/up. Maurice reported that when carrier is not
ok and xsk_pool is present on ring pair, ksoftirqd will consume 100% CPU
cycles due to the constant NAPI rescheduling as ixgbe_poll() states that
there is still some work to be done.
To fix this, do not set work_done to false for a !netif_carrier_ok().
Fixes: c685c69fba ("ixgbe: don't do any AF_XDP zero-copy transmit if netif is not OK")
Reported-by: Maurice Baijens <maurice.baijens@ellips.com>
Tested-by: Maurice Baijens <maurice.baijens@ellips.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd6f1fd5d3 upstream.
During driver initialization, the pointer of card info, i.e. the
variable 'ci' is required. However, the definition of
'com20020pci_id_table' reveals that this field is empty for some
devices, which will cause null pointer dereference when initializing
these devices.
The following log reveals it:
[ 3.973806] KASAN: null-ptr-deref in range [0x0000000000000028-0x000000000000002f]
[ 3.973819] RIP: 0010:com20020pci_probe+0x18d/0x13e0 [com20020_pci]
[ 3.975181] Call Trace:
[ 3.976208] local_pci_probe+0x13f/0x210
[ 3.977248] pci_device_probe+0x34c/0x6d0
[ 3.977255] ? pci_uevent+0x470/0x470
[ 3.978265] really_probe+0x24c/0x8d0
[ 3.978273] __driver_probe_device+0x1b3/0x280
[ 3.979288] driver_probe_device+0x50/0x370
Fix this by checking whether the 'ci' is a null pointer first.
Fixes: 8c14f9c703 ("ARCNET: add com20020 PCI IDs with metadata")
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 570425f8c7 upstream.
Finish initializing the adapter before registering netdev so state
is consistent.
Fixes: c26eba03e4 ("ibmvnic: Update reset infrastructure to support tunable parameters")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 94d9864cc8 upstream.
When we get anti-clogging token required (added by the commit
mentioned below), or the other status codes added by the later
commit 4e56cde15f ("mac80211: Handle special status codes in
SAE commit") we currently just pretend (towards the internal
state machine of authentication) that we didn't receive anything.
This has the undesirable consequence of retransmitting the prior
frame, which is not expected, because the timer is still armed.
If we just disarm the timer at that point, it would result in
the undesirable side effect of being in this state indefinitely
if userspace crashes, or so.
So to fix this, reset the timer and set a new auth_data->waiting
in order to have no more retransmissions, but to have the data
destroyed when the timer actually fires, which will only happen
if userspace didn't continue (i.e. crashed or abandoned it.)
Fixes: a4055e74a2 ("mac80211: Don't destroy auth data in case of anti-clogging")
Reported-by: Jouni Malinen <j@w1.fi>
Link: https://lore.kernel.org/r/20220224103932.75964e1d7932.Ia487f91556f29daae734bf61f8181404642e1eec@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 859ae70183 upstream.
There are two problems with the current code that have been highlighted
with the AQL feature that is now enbaled by default.
First problem is in ieee80211_rx_h_mesh_fwding(),
ieee80211_select_queue_80211() is used on received packets to choose
the sending AC queue of the forwarding packet although this function
should only be called on TX packet (it uses ieee80211_tx_info).
This ends with forwarded mesh packets been sent on unrelated random AC
queue. To fix that, AC queue can directly be infered from skb->priority
which has been extracted from QOS info (see ieee80211_parse_qos()).
Second problem is the value of queue_mapping set on forwarded mesh
frames via skb_set_queue_mapping() is not the AC of the packet but a
hardware queue index. This may or may not work depending on AC to HW
queue mapping which is driver specific.
Both of these issues lead to improper AC selection while forwarding
mesh packets but more importantly due to improper airtime accounting
(which is done on a per STA, per AC basis) caused traffic stall with
the introduction of AQL.
Fixes: cf44012810 ("mac80211: fix unnecessary frame drops in mesh fwding")
Fixes: d3c1597b8d ("mac80211: fix forwarded mesh frame queue mapping")
Co-developed-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Nicolas Escande <nico.escande@gmail.com>
Link: https://lore.kernel.org/r/20220214173214.368862-1-nico.escande@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 620a6dc407 upstream.
The deduplicating sort in sched_init_numa() assumes that the first line in
the distance table contains all unique values in the entire table. I've
been trying to pen what this exactly means for the topology, but it's not
straightforward. For instance, topology.c uses this example:
node 0 1 2 3
0: 10 20 20 30
1: 20 10 20 20
2: 20 20 10 20
3: 30 20 20 10
0 ----- 1
| / |
| / |
| / |
2 ----- 3
Which works out just fine. However, if we swap nodes 0 and 1:
1 ----- 0
| / |
| / |
| / |
2 ----- 3
we get this distance table:
node 0 1 2 3
0: 10 20 20 20
1: 20 10 20 30
2: 20 20 10 20
3: 20 30 20 10
Which breaks the deduplicating sort (non-representative first line). In
this case this would just be a renumbering exercise, but it so happens that
we can have a deduplicating sort that goes through the whole table in O(n²)
at the extra cost of a temporary memory allocation (i.e. any form of set).
The ACPI spec (SLIT) mentions distances are encoded on 8 bits. Following
this, implement the set as a 256-bits bitmap. Should this not be
satisfactory (i.e. we want to support 32-bit values), then we'll have to go
for some other sparse set implementation.
This has the added benefit of letting us allocate just the right amount of
memory for sched_domains_numa_distance[], rather than an arbitrary
(nr_node_ids + 1).
Note: DT binding equivalent (distance-map) decodes distances as 32-bit
values.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20210122123943.1217-2-valentin.schneider@arm.com
Signed-off-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fadead80fe upstream.
Commit c503e63200 ("ice: Stop processing VF messages during teardown")
introduced a driver state flag, ICE_VF_DEINIT_IN_PROGRESS, which is
intended to prevent some issues with concurrently handling messages from
VFs while tearing down the VFs.
This change was motivated by crashes caused while tearing down and
bringing up VFs in rapid succession.
It turns out that the fix actually introduces issues with the VF driver
caused because the PF no longer responds to any messages sent by the VF
during its .remove routine. This results in the VF potentially removing
its DMA memory before the PF has shut down the device queues.
Additionally, the fix doesn't actually resolve concurrency issues within
the ice driver. It is possible for a VF to initiate a reset just prior
to the ice driver removing VFs. This can result in the remove task
concurrently operating while the VF is being reset. This results in
similar memory corruption and panics purportedly fixed by that commit.
Fix this concurrency at its root by protecting both the reset and
removal flows using the existing VF cfg_lock. This ensures that we
cannot remove the VF while any outstanding critical tasks such as a
virtchnl message or a reset are occurring.
This locking change also fixes the root cause originally fixed by commit
c503e63200 ("ice: Stop processing VF messages during teardown"), so we
can simply revert it.
Note that I kept these two changes together because simply reverting the
original commit alone would leave the driver vulnerable to worse race
conditions.
Fixes: c503e63200 ("ice: Stop processing VF messages during teardown")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e6ba5273d4 upstream.
The VF can be configured via the PF's ndo ops at the same time the PF is
receiving/handling virtchnl messages. This has many issues, with
one of them being the ndo op could be actively resetting a VF (i.e.
resetting it to the default state and deleting/re-adding the VF's VSI)
while a virtchnl message is being handled. The following error was seen
because a VF ndo op was used to change a VF's trust setting while the
VIRTCHNL_OP_CONFIG_VSI_QUEUES was ongoing:
[35274.192484] ice 0000:88:00.0: Failed to set LAN Tx queue context, error: ICE_ERR_PARAM
[35274.193074] ice 0000:88:00.0: VF 0 failed opcode 6, retval: -5
[35274.193640] iavf 0000:88:01.0: PF returned error -5 (IAVF_ERR_PARAM) to our request 6
Fix this by making sure the virtchnl handling and VF ndo ops that
trigger VF resets cannot run concurrently. This is done by adding a
struct mutex cfg_lock to each VF structure. For VF ndo ops, the mutex
will be locked around the critical operations and VFR. Since the ndo ops
will trigger a VFR, the virtchnl thread will use mutex_trylock(). This
is done because if any other thread (i.e. VF ndo op) has the mutex, then
that means the current VF message being handled is no longer valid, so
just ignore it.
This issue can be seen using the following commands:
for i in {0..50}; do
rmmod ice
modprobe ice
sleep 1
echo 1 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 1 > /sys/class/net/ens785f1/device/sriov_numvfs
ip link set ens785f1 vf 0 trust on
ip link set ens785f0 vf 0 trust on
sleep 2
echo 0 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 0 > /sys/class/net/ens785f1/device/sriov_numvfs
sleep 1
echo 1 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 1 > /sys/class/net/ens785f1/device/sriov_numvfs
ip link set ens785f1 vf 0 trust on
ip link set ens785f0 vf 0 trust on
done
Fixes: 7c710869d6 ("ice: Add handlers for VF netdevice operations")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2fcf21020 upstream.
This sequence of events can lead to a failure to requeue a CPU's
->nocb_timer:
1. There are no callbacks queued for any CPU covered by CPU 0-2's
->nocb_gp_kthread. Note that ->nocb_gp_kthread is associated
with CPU 0.
2. CPU 1 enqueues its first callback with interrupts disabled, and
thus must defer awakening its ->nocb_gp_kthread. It therefore
queues its rcu_data structure's ->nocb_timer. At this point,
CPU 1's rdp->nocb_defer_wakeup is RCU_NOCB_WAKE.
3. CPU 2, which shares the same ->nocb_gp_kthread, also enqueues a
callback, but with interrupts enabled, allowing it to directly
awaken the ->nocb_gp_kthread.
4. The newly awakened ->nocb_gp_kthread associates both CPU 1's
and CPU 2's callbacks with a future grace period and arranges
for that grace period to be started.
5. This ->nocb_gp_kthread goes to sleep waiting for the end of this
future grace period.
6. This grace period elapses before the CPU 1's timer fires.
This is normally improbably given that the timer is set for only
one jiffy, but timers can be delayed. Besides, it is possible
that kernel was built with CONFIG_RCU_STRICT_GRACE_PERIOD=y.
7. The grace period ends, so rcu_gp_kthread awakens the
->nocb_gp_kthread, which in turn awakens both CPU 1's and
CPU 2's ->nocb_cb_kthread. Then ->nocb_gb_kthread sleeps
waiting for more newly queued callbacks.
8. CPU 1's ->nocb_cb_kthread invokes its callback, then sleeps
waiting for more invocable callbacks.
9. Note that neither kthread updated any ->nocb_timer state,
so CPU 1's ->nocb_defer_wakeup is still set to RCU_NOCB_WAKE.
10. CPU 1 enqueues its second callback, this time with interrupts
enabled so it can wake directly ->nocb_gp_kthread.
It does so with calling wake_nocb_gp() which also cancels the
pending timer that got queued in step 2. But that doesn't reset
CPU 1's ->nocb_defer_wakeup which is still set to RCU_NOCB_WAKE.
So CPU 1's ->nocb_defer_wakeup and its ->nocb_timer are now
desynchronized.
11. ->nocb_gp_kthread associates the callback queued in 10 with a new
grace period, arranges for that grace period to start and sleeps
waiting for it to complete.
12. The grace period ends, rcu_gp_kthread awakens ->nocb_gp_kthread,
which in turn wakes up CPU 1's ->nocb_cb_kthread which then
invokes the callback queued in 10.
13. CPU 1 enqueues its third callback, this time with interrupts
disabled so it must queue a timer for a deferred wakeup. However
the value of its ->nocb_defer_wakeup is RCU_NOCB_WAKE which
incorrectly indicates that a timer is already queued. Instead,
CPU 1's ->nocb_timer was cancelled in 10. CPU 1 therefore fails
to queue the ->nocb_timer.
14. CPU 1 has its pending callback and it may go unnoticed until
some other CPU ever wakes up ->nocb_gp_kthread or CPU 1 ever
calls an explicit deferred wakeup, for example, during idle entry.
This commit fixes this bug by resetting rdp->nocb_defer_wakeup everytime
we delete the ->nocb_timer.
It is quite possible that there is a similar scenario involving
->nocb_bypass_timer and ->nocb_defer_wakeup. However, despite some
effort from several people, a failure scenario has not yet been located.
However, that by no means guarantees that no such scenario exists.
Finding a failure scenario is left as an exercise for the reader, and the
"Fixes:" tag below relates to ->nocb_bypass_timer instead of ->nocb_timer.
Fixes: d1b222c6be (rcu/nocb: Add bypass callback queueing)
Cc: <stable@vger.kernel.org>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Lai Jiangshan <jiangshanlai@gmail.com>
Cc: Joel Fernandes <joel@joelfernandes.org>
Cc: Boqun Feng <boqun.feng@gmail.com>
Reviewed-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4940a1fdf3 upstream.
The problem of SMC_CLC_DECL_ERR_REGRMB on the server is very clear.
Based on the fact that whether a new SMC connection can be accepted or
not depends on not only the limit of conn nums, but also the available
entries of rtoken. Since the rtoken release is trigger by peer, while
the conn nums is decrease by local, tons of thing can happen in this
time difference.
This only thing that needs to be mentioned is that now all connection
creations are completely protected by smc_server_lgr_pending lock, it's
enough to check only the available entries in rtokens_used_mask.
Fixes: cd6851f303 ("smc: remote memory buffers (RMBs)")
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0537f0a215 upstream.
The main reason for this unexpected SMC_CLC_DECL_ERR_REGRMB in client
dues to following execution sequence:
Server Conn A: Server Conn B: Client Conn B:
smc_lgr_unregister_conn
smc_lgr_register_conn
smc_clc_send_accept ->
smc_rtoken_add
smcr_buf_unuse
-> Client Conn A:
smc_rtoken_delete
smc_lgr_unregister_conn() makes current link available to assigned to new
incoming connection, while smcr_buf_unuse() has not executed yet, which
means that smc_rtoken_add may fail because of insufficient rtoken_entry,
reversing their execution order will avoid this problem.
Fixes: 3e034725c0 ("net/smc: common functions for RMBs and send buffers")
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9f1c50cf39 upstream.
There's a potential leak issue under following execution sequence :
smc_release smc_connect_work
if (sk->sk_state == SMC_INIT)
send_clc_confirim
tcp_abort();
...
sk.sk_state = SMC_ACTIVE
smc_close_active
switch(sk->sk_state) {
...
case SMC_ACTIVE:
smc_close_final()
// then wait peer closed
Unfortunately, tcp_abort() may discard CLC CONFIRM messages that are
still in the tcp send buffer, in which case our connection token cannot
be delivered to the server side, which means that we cannot get a
passive close message at all. Therefore, it is impossible for the to be
disconnected at all.
This patch tries a very simple way to avoid this issue, once the state
has changed to SMC_ACTIVE after tcp_abort(), we can actively abort the
smc connection, considering that the state is SMC_INIT before
tcp_abort(), abandoning the complete disconnection process should not
cause too much problem.
In fact, this problem may exist as long as the CLC CONFIRM message is
not received by the server. Whether a timer should be added after
smc_close_final() needs to be discussed in the future. But even so, this
patch provides a faster release for connection in above case, it should
also be valuable.
Fixes: 39f41f367b ("net/smc: common release code for non-accepted sockets")
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 91b0383fef upstream.
If I'm not mistaken (and I don't think I am), the way in which the
dcbnl_ops work is that drivers call dcb_ieee_setapp() and this populates
the application table with dynamically allocated struct dcb_app_type
entries that are kept in the module-global dcb_app_list.
However, nobody keeps exact track of these entries, and although
dcb_ieee_delapp() is supposed to remove them, nobody does so when the
interface goes away (example: driver unbinds from device). So the
dcb_app_list will contain lingering entries with an ifindex that no
longer matches any device in dcb_app_lookup().
Reclaim the lost memory by listening for the NETDEV_UNREGISTER event and
flushing the app table entries of interfaces that are now gone.
In fact something like this used to be done as part of the initial
commit (blamed below), but it was done in dcbnl_exit() -> dcb_flushapp(),
essentially at module_exit time. That became dead code after commit
7a6b6f515f ("DCB: fix kconfig option") which essentially merged
"tristate config DCB" and "bool config DCBNL" into a single "bool config
DCB", so net/dcb/dcbnl.c could not be built as a module anymore.
Commit 36b9ad8084 ("net/dcb: make dcbnl.c explicitly non-modular")
recognized this and deleted dcbnl_exit() and dcb_flushapp() altogether,
leaving us with the version we have today.
Since flushing application table entries can and should be done as soon
as the netdevice disappears, fundamentally the commit that is to blame
is the one that introduced the design of this API.
Fixes: 9ab933ab2c ("dcbnl: add appliction tlv handlers")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9995b408f1 upstream.
There are two reasons for addrconf_notify() to be called with NETDEV_DOWN:
either the network device is actually going down, or IPv6 was disabled
on the interface.
If either of them stays down while the other is toggled, we repeatedly
call the code for NETDEV_DOWN, including ipv6_mc_down(), while never
calling the corresponding ipv6_mc_up() in between. This will cause a
new entry in idev->mc_tomb to be allocated for each multicast group
the interface is subscribed to, which in turn leaks one struct ifmcaddr6
per nontrivial multicast group the interface is subscribed to.
The following reproducer will leak at least $n objects:
ip addr add ff2e::4242/32 dev eth0 autojoin
sysctl -w net.ipv6.conf.eth0.disable_ipv6=1
for i in $(seq 1 $n); do
ip link set up eth0; ip link set down eth0
done
Joining groups with IPV6_ADD_MEMBERSHIP (unprivileged) or setting the
sysctl net.ipv6.conf.eth0.forwarding to 1 (=> subscribing to ff02::2)
can also be used to create a nontrivial idev->mc_list, which will the
leak objects with the right up-down-sequence.
Based on both sources for NETDEV_DOWN events the interface IPv6 state
should be considered:
- not ready if the network interface is not ready OR IPv6 is disabled
for it
- ready if the network interface is ready AND IPv6 is enabled for it
The functions ipv6_mc_up() and ipv6_down() should only be run when this
state changes.
Implement this by remembering when the IPv6 state is ready, and only
run ipv6_mc_down() if it actually changed from ready to not ready.
The other direction (not ready -> ready) already works correctly, as:
- the interface notification triggered codepath for NETDEV_UP /
NETDEV_CHANGE returns early if ipv6 is disabled, and
- the disable_ipv6=0 triggered codepath skips fully initializing the
interface as long as addrconf_link_ready(dev) returns false
- calling ipv6_mc_up() repeatedly does not leak anything
Fixes: 3ce62a84d5 ("ipv6: exit early in addrconf_notify() if IPv6 is disabled")
Signed-off-by: Johannes Nixdorf <j.nixdorf@avm.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c1f41afc1 upstream.
The ifindex doesn't have to be unique for multiple network namespaces on
the same machine.
$ ip netns add test1
$ ip -net test1 link add dummy1 type dummy
$ ip netns add test2
$ ip -net test2 link add dummy2 type dummy
$ ip -net test1 link show dev dummy1
6: dummy1: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 96:81:55:1e:dd:85 brd ff:ff:ff:ff:ff:ff
$ ip -net test2 link show dev dummy2
6: dummy2: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 5a:3c:af:35:07:c3 brd ff:ff:ff:ff:ff:ff
But the batman-adv code to walk through the various layers of virtual
interfaces uses this assumption because dev_get_iflink handles it
internally and doesn't return the actual netns of the iflink. And
dev_get_iflink only documents the situation where ifindex == iflink for
physical devices.
But only checking for dev->netdev_ops->ndo_get_iflink is also not an option
because ipoib_get_iflink implements it even when it sometimes returns an
iflink != ifindex and sometimes iflink == ifindex. The caller must
therefore make sure itself to check both netns and iflink + ifindex for
equality. Only when they are equal, a "physical" interface was detected
which should stop the traversal. On the other hand, vxcan_get_iflink can
also return 0 in case there was currently no valid peer. In this case, it
is still necessary to stop.
Fixes: b7eddd0b39 ("batman-adv: prevent using any virtual device created on batman-adv as hard-interface")
Fixes: 5ed4a460a1 ("batman-adv: additional checks for virtual interfaces on top of WiFi")
Reported-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6116ba0942 upstream.
There is no need to call dev_get_iflink multiple times for the same
net_device in batadv_get_real_netdevice. And since some of the
ndo_get_iflink callbacks are dynamic (for example via RCUs like in
vxcan_get_iflink), it could easily happen that the returned values are not
stable. The pre-checks before __dev_get_by_index are then of course bogus.
Fixes: 5ed4a460a1 ("batman-adv: additional checks for virtual interfaces on top of WiFi")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 690bb6fb64 upstream.
There is no need to call dev_get_iflink multiple times for the same
net_device in batadv_is_on_batman_iface. And since some of the
.ndo_get_iflink callbacks are dynamic (for example via RCUs like in
vxcan_get_iflink), it could easily happen that the returned values are not
stable. The pre-checks before __dev_get_by_index are then of course bogus.
Fixes: b7eddd0b39 ("batman-adv: prevent using any virtual device created on batman-adv as hard-interface")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b836da408 upstream.
In case someone combines bpf socket assign and nf_queue, then we will
queue an skb who references a struct sock that did not have its
reference count incremented.
As we leave rcu protection, there is no guarantee that skb->sk is still
valid.
For refcount-less skb->sk case, try to increment the reference count
and then override the destructor.
In case of failure we have two choices: orphan the skb and 'delete'
preselect or let nf_queue() drop the packet.
Do the latter, it should not happen during normal operation.
Fixes: cf7fbe660f ("bpf: Add socket assign support")
Acked-by: Joe Stringer <joe@cilium.io>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c387307024 upstream.
Eric Dumazet says:
The sock_hold() side seems suspect, because there is no guarantee
that sk_refcnt is not already 0.
On failure, we cannot queue the packet and need to indicate an
error. The packet will be dropped by the caller.
v2: split skb prefetch hunk into separate change
Fixes: 271b72c7fa ("udp: RCU handling for Unicast packets.")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 747670fd9a upstream.
There is no guarantee that state->sk refers to a full socket.
If refcount transitions to 0, sock_put calls sk_free which then ends up
with garbage fields.
I'd like to thank Oleksandr Natalenko and Jiri Benc for considerable
debug work and pointing out state->sk oddities.
Fixes: ca6fb06518 ("tcp: attach SYNACK messages to request sockets instead of listener")
Tested-by: Oleksandr Natalenko <oleksandr@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 224102de2f upstream.
The truesize for a UDP GRO packet is added by main skb and skbs in main
skb's frag_list:
skb_gro_receive_list
p->truesize += skb->truesize;
The commit 53475c5dd8 ("net: fix use-after-free when UDP GRO with
shared fraglist") introduced a truesize increase for frag_list skbs.
When uncloning skb, it will call pskb_expand_head and trusesize for
frag_list skbs may increase. This can occur when allocators uses
__netdev_alloc_skb and not jump into __alloc_skb. This flow does not
use ksize(len) to calculate truesize while pskb_expand_head uses.
skb_segment_list
err = skb_unclone(nskb, GFP_ATOMIC);
pskb_expand_head
if (!skb->sk || skb->destructor == sock_edemux)
skb->truesize += size - osize;
If we uses increased truesize adding as delta_truesize, it will be
larger than before and even larger than previous total truesize value
if skbs in frag_list are abundant. The main skb truesize will become
smaller and even a minus value or a huge value for an unsigned int
parameter. Then the following memory check will drop this abnormal skb.
To avoid this error we should use the original truesize to segment the
main skb.
Fixes: 53475c5dd8 ("net: fix use-after-free when UDP GRO with shared fraglist")
Signed-off-by: lena wang <lena.wang@mediatek.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/1646133431-8948-1-git-send-email-lena.wang@mediatek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c76ecd9c9 upstream.
struct xfrm_user_offload has flags variable that received user input,
but kernel didn't check if valid bits were provided. It caused a situation
where not sanitized input was forwarded directly to the drivers.
For example, XFRM_OFFLOAD_IPV6 define that was exposed, was used by
strongswan, but not implemented in the kernel at all.
As a solution, check and sanitize input flags to forward
XFRM_OFFLOAD_INBOUND to the drivers.
Fixes: d77e38e612 ("xfrm: Add an IPsec hardware offloading API")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6596a02295 upstream.
Commit 749439bfac ("ipv6: fix udpv6
sendmsg crash caused by too small MTU") breaks PMTU for xfrm.
A Packet Too Big ICMPv6 message received in response to an ESP
packet will prevent all further communication through the tunnel
if the reported MTU minus the ESP overhead is smaller than 1280.
E.g. in a case of a tunnel-mode ESP with sha256/aes the overhead
is 92 bytes. Receiving a PTB with MTU of 1371 or less will result
in all further packets in the tunnel dropped. A ping through the
tunnel fails with "ping: sendmsg: Invalid argument".
Apparently the MTU on the xfrm route is smaller than 1280 and
fails the check inside ip6_setup_cork() added by 749439bf.
We found this by debugging USGv6/ipv6ready failures. Failing
tests are: "Phase-2 Interoperability Test Scenario IPsec" /
5.3.11 and 5.4.11 (Tunnel Mode: Fragmentation).
Commit b515d26372 ("xfrm:
xfrm_state_mtu should return at least 1280 for ipv6") attempted
to fix this but caused another regression in TCP MSS calculations
and had to be reverted.
The patch below fixes the situation by dropping the MTU
check and instead checking for the underflows described in the
749439bf commit message.
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Fixes: 749439bfac ("ipv6: fix udpv6 sendmsg crash caused by too small MTU")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0708a0afe2 upstream.
syzkaller was recently triggering an oversized kvmalloc() warning via
xdp_umem_create().
The triggered warning was added back in 7661809d49 ("mm: don't allow
oversized kvmalloc() calls"). The rationale for the warning for huge
kvmalloc sizes was as a reaction to a security bug where the size was
more than UINT_MAX but not everything was prepared to handle unsigned
long sizes.
Anyway, the AF_XDP related call trace from this syzkaller report was:
kvmalloc include/linux/mm.h:806 [inline]
kvmalloc_array include/linux/mm.h:824 [inline]
kvcalloc include/linux/mm.h:829 [inline]
xdp_umem_pin_pages net/xdp/xdp_umem.c:102 [inline]
xdp_umem_reg net/xdp/xdp_umem.c:219 [inline]
xdp_umem_create+0x6a5/0xf00 net/xdp/xdp_umem.c:252
xsk_setsockopt+0x604/0x790 net/xdp/xsk.c:1068
__sys_setsockopt+0x1fd/0x4e0 net/socket.c:2176
__do_sys_setsockopt net/socket.c:2187 [inline]
__se_sys_setsockopt net/socket.c:2184 [inline]
__x64_sys_setsockopt+0xb5/0x150 net/socket.c:2184
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
Björn mentioned that requests for >2GB allocation can still be valid:
The structure that is being allocated is the page-pinning accounting.
AF_XDP has an internal limit of U32_MAX pages, which is *a lot*, but
still fewer than what memcg allows (PAGE_COUNTER_MAX is a LONG_MAX/
PAGE_SIZE on 64 bit systems). [...]
I could just change from U32_MAX to INT_MAX, but as I stated earlier
that has a hacky feeling to it. [...] From my perspective, the code
isn't broken, with the memcg limits in consideration. [...]
Linus says:
[...] Pretty much every time this has come up, the kernel warning has
shown that yes, the code was broken and there really wasn't a reason
for doing allocations that big.
Of course, some people would be perfectly fine with the allocation
failing, they just don't want the warning. I didn't want __GFP_NOWARN
to shut it up originally because I wanted people to see all those
cases, but these days I think we can just say "yeah, people can shut
it up explicitly by saying 'go ahead and fail this allocation, don't
warn about it'".
So enough time has passed that by now I'd certainly be ok with [it].
Thus allow call-sites to silence such userspace triggered splats if the
allocation requests have __GFP_NOWARN. For xdp_umem_pin_pages()'s call
to kvcalloc() this is already the case, so nothing else needed there.
Fixes: 7661809d49 ("mm: don't allow oversized kvmalloc() calls")
Reported-by: syzbot+11421fbbff99b989670e@syzkaller.appspotmail.com
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: syzbot+11421fbbff99b989670e@syzkaller.appspotmail.com
Cc: Björn Töpel <bjorn@kernel.org>
Cc: Magnus Karlsson <magnus.karlsson@intel.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Andrii Nakryiko <andrii@kernel.org>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: David S. Miller <davem@davemloft.net>
Link: https://lore.kernel.org/bpf/CAJ+HfNhyfsT5cS_U9EC213ducHs9k9zNxX9+abqC0kTrPbQ0gg@mail.gmail.com
Link: https://lore.kernel.org/bpf/20211201202905.b9892171e3f5b9a60f9da251@linux-foundation.org
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Ackd-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d5081bf5dc upstream.
The field offset for port configuration status on SPR has been changed to
bit 14 from ICX where it resides at bit 12. By chance link status detection
continued to work on SPR. This is due to bit 12 being a configuration bit
which is in sync with the status bit. Fix this by checking for a SPR device
and checking correct status bit.
Fixes: 26bfe3d0b2 ("ntb: intel: Add Icelake (gen4) support for Intel NTB")
Tested-by: Jerry Dai <jerry.dai@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ce97f4ec5 upstream.
The AMD IOMMU logs I/O page faults and such to a ring buffer in
system memory, and this ring buffer can overflow. The AMD IOMMU
spec has the following to say about the interrupt status bit that
signals this overflow condition:
EventOverflow: Event log overflow. RW1C. Reset 0b. 1 = IOMMU
event log overflow has occurred. This bit is set when a new
event is to be written to the event log and there is no usable
entry in the event log, causing the new event information to
be discarded. An interrupt is generated when EventOverflow = 1b
and MMIO Offset 0018h[EventIntEn] = 1b. No new event log
entries are written while this bit is set. Software Note: To
resume logging, clear EventOverflow (W1C), and write a 1 to
MMIO Offset 0018h[EventLogEn].
The AMD IOMMU driver doesn't currently implement this recovery
sequence, meaning that if a ring buffer overflow occurs, logging
of EVT/PPR/GA events will cease entirely.
This patch implements the spec-mandated reset sequence, with the
minor tweak that the hardware seems to want to have a 0 written to
MMIO Offset 0018h[EventLogEn] first, before writing an 1 into this
field, or the IOMMU won't actually resume logging events.
Signed-off-by: Lennert Buytenhek <buytenh@arista.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/YVrSXEdW2rzEfOvk@wantstofly.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c648c4bb7d upstream.
__virt_to_phys function is called very early in the boot process (ie
kasan_early_init) so it should not be instrumented by KASAN otherwise it
bugs.
Fix this by declaring phys_addr.c as non-kasan instrumentable.
Signed-off-by: Alexandre Ghiti <alexandre.ghiti@canonical.com>
Fixes: 8ad8b72721 (riscv: Add KASAN support)
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a3d3280378 upstream.
In order to get the pfn of a struct page* when sparsemem is enabled
without vmemmap, the mem_section structures need to be initialized which
happens in sparse_init.
But kasan_early_init calls pfn_to_page way before sparse_init is called,
which then tries to dereference a null mem_section pointer.
Fix this by removing the usage of this function in kasan_early_init.
Fixes: 8ad8b72721 ("riscv: Add KASAN support")
Signed-off-by: Alexandre Ghiti <alexandre.ghiti@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f37c3bbc63 ]
Since referencing user space pointers is special, if the user wants to
filter on a field that is a pointer to user space, then they need to
specify it.
Add a ".ustring" attribute to the field name for filters to state that the
field is pointing to user space such that the kernel can take the
appropriate action to read that pointer.
Link: https://lore.kernel.org/all/yt9d8rvmt2jq.fsf@linux.ibm.com/
Fixes: 77360f9bbc ("tracing: Add test for user space strings when filtering on string pointers")
Tested-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1a66c3bc4 ]
Workstation application ANSA/META v21.1.4 get this error dmesg when
running CI test suite provided by ANSA/META:
[drm:amdgpu_gem_va_ioctl [amdgpu]] *ERROR* Couldn't update BO_VA (-16)
This is caused by:
1. create a 256MB buffer in invisible VRAM
2. CPU map the buffer and access it causes vm_fault and try to move
it to visible VRAM
3. force visible VRAM space and traverse all VRAM bos to check if
evicting this bo is valuable
4. when checking a VM bo (in invisible VRAM), amdgpu_vm_evictable()
will set amdgpu_vm->evicting, but latter due to not in visible
VRAM, won't really evict it so not add it to amdgpu_vm->evicted
5. before next CS to clear the amdgpu_vm->evicting, user VM ops
ioctl will pass amdgpu_vm_ready() (check amdgpu_vm->evicted)
but fail in amdgpu_vm_bo_update_mapping() (check
amdgpu_vm->evicting) and get this error log
This error won't affect functionality as next CS will finish the
waiting VM ops. But we'd better clear the error log by checking
the amdgpu_vm->evicting flag in amdgpu_vm_ready() to stop calling
amdgpu_vm_bo_update_mapping() later.
Another reason is amdgpu_vm->evicted list holds all BOs (both
user buffer and page table), but only page table BOs' eviction
prevent VM ops. amdgpu_vm->evicting flag is set only for page
table BOs, so we should use evicting flag instead of evicted list
in amdgpu_vm_ready().
The side effect of this change is: previously blocked VM op (user
buffer in "evicted" list but no page table in it) gets done
immediately.
v2: update commit comments.
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Qiang Yu <qiang.yu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77360f9bbc ]
Pingfan reported that the following causes a fault:
echo "filename ~ \"cpu\"" > events/syscalls/sys_enter_openat/filter
echo 1 > events/syscalls/sys_enter_at/enable
The reason is that trace event filter treats the user space pointer
defined by "filename" as a normal pointer to compare against the "cpu"
string. The following bug happened:
kvm-03-guest16 login: [72198.026181] BUG: unable to handle page fault for address: 00007fffaae8ef60
#PF: supervisor read access in kernel mode
#PF: error_code(0x0001) - permissions violation
PGD 80000001008b7067 P4D 80000001008b7067 PUD 2393f1067 PMD 2393ec067 PTE 8000000108f47867
Oops: 0001 [#1] PREEMPT SMP PTI
CPU: 1 PID: 1 Comm: systemd Kdump: loaded Not tainted 5.14.0-32.el9.x86_64 #1
Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
RIP: 0010:strlen+0x0/0x20
Code: 48 89 f9 74 09 48 83 c1 01 80 39 00 75 f7 31 d2 44 0f b6 04 16 44 88 04 11
48 83 c2 01 45 84 c0 75 ee c3 0f 1f 80 00 00 00 00 <80> 3f 00 74 10 48 89 f8
48 83 c0 01 80 38 00 75 f7 48 29 f8 c3 31
RSP: 0018:ffffb5b900013e48 EFLAGS: 00010246
RAX: 0000000000000018 RBX: ffff8fc1c49ede00 RCX: 0000000000000000
RDX: 0000000000000020 RSI: ffff8fc1c02d601c RDI: 00007fffaae8ef60
RBP: 00007fffaae8ef60 R08: 0005034f4ddb8ea4 R09: 0000000000000000
R10: ffff8fc1c02d601c R11: 0000000000000000 R12: ffff8fc1c8a6e380
R13: 0000000000000000 R14: ffff8fc1c02d6010 R15: ffff8fc1c00453c0
FS: 00007fa86123db40(0000) GS:ffff8fc2ffd00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fffaae8ef60 CR3: 0000000102880001 CR4: 00000000007706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
filter_pred_pchar+0x18/0x40
filter_match_preds+0x31/0x70
ftrace_syscall_enter+0x27a/0x2c0
syscall_trace_enter.constprop.0+0x1aa/0x1d0
do_syscall_64+0x16/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7fa861d88664
The above happened because the kernel tried to access user space directly
and triggered a "supervisor read access in kernel mode" fault. Worse yet,
the memory could not even be loaded yet, and a SEGFAULT could happen as
well. This could be true for kernel space accessing as well.
To be even more robust, test both kernel and user space strings. If the
string fails to read, then simply have the filter fail.
Note, TASK_SIZE is used to determine if the pointer is user or kernel space
and the appropriate strncpy_from_kernel/user_nofault() function is used to
copy the memory. For some architectures, the compare to TASK_SIZE may always
pick user space or kernel space. If it gets it wrong, the only thing is that
the filter will fail to match. In the future, this needs to be fixed to have
the event denote which should be used. But failing a filter is much better
than panicing the machine, and that can be solved later.
Link: https://lore.kernel.org/all/20220107044951.22080-1-kernelfans@gmail.com/
Link: https://lkml.kernel.org/r/20220110115532.536088fd@gandalf.local.home
Cc: stable@vger.kernel.org
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Tom Zanussi <zanussi@kernel.org>
Reported-by: Pingfan Liu <kernelfans@gmail.com>
Tested-by: Pingfan Liu <kernelfans@gmail.com>
Fixes: 87a342f5db ("tracing/filters: Support filtering for char * strings")
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92fba084b7 ]
In exfat_truncate(), the computation of inode->i_blocks is wrong if
the file is larger than 4 GiB because a 32-bit variable is used as a
mask. This is fixed and simplified by using round_up().
Also fix the same buggy computation in exfat_read_root() and another
(correct) one in exfat_fill_inode(). The latter was fixed another way
last month but can be simplified by using round_up() as well. See:
commit 0c336d6e33 ("exfat: fix incorrect loading of i_blocks for
large files")
Fixes: 98d917047e ("exfat: add file operations")
Cc: stable@vger.kernel.org # v5.7+
Suggested-by: Matthew Wilcox <willy@infradead.org>
Reviewed-by: Sungjong Seo <sj1557.seo@samsung.com>
Signed-off-by: Christophe Vu-Brugier <christophe.vu-brugier@seagate.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21e8a96377 ]
Add quirk CDC_MBIM_FLAG_AVOID_ALTSETTING_TOGGLE for Telit FN990
0x1071 composition in order to avoid bind error.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5de7179740 ]
Driver builds fine with COMPILE_TEST. Enable it for wider test coverage
and easier maintenance.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b0dcb3882 ]
Driver builds fine with COMPILE_TEST. Enable it for wider test coverage
and easier maintenance.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21bffcb76e ]
seccomp_bpf failed on tests 47 global.user_notification_filter_empty
and 48 global.user_notification_filter_empty_threaded when it's
tested on updated kernel but with old kernel headers. Because old
kernel headers don't have definition of macro __NR_clone3 which is
required for these two tests. Since under selftests/, we can install
headers once for all tests (the default INSTALL_HDR_PATH is
usr/include), fix it by adding usr/include to the list of directories
to be searched. Use "-isystem" to indicate it's a system directory as
the real kernel headers directories are.
Signed-off-by: Sherry Yang <sherry.yang@oracle.com>
Tested-by: Sherry Yang <sherry.yang@oracle.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d6cc9898e ]
When cifs_get_root() fails during cifs_smb3_do_mount() we call
deactivate_locked_super() which eventually will call delayed_free() which
will free the context.
In this situation we should not proceed to enter the out: section in
cifs_smb3_do_mount() and free the same resources a second time.
[Thu Feb 10 12:59:06 2022] BUG: KASAN: use-after-free in rcu_cblist_dequeue+0x32/0x60
[Thu Feb 10 12:59:06 2022] Read of size 8 at addr ffff888364f4d110 by task swapper/1/0
[Thu Feb 10 12:59:06 2022] CPU: 1 PID: 0 Comm: swapper/1 Tainted: G OE 5.17.0-rc3+ #4
[Thu Feb 10 12:59:06 2022] Hardware name: Microsoft Corporation Virtual Machine/Virtual Machine, BIOS Hyper-V UEFI Release v4.0 12/17/2019
[Thu Feb 10 12:59:06 2022] Call Trace:
[Thu Feb 10 12:59:06 2022] <IRQ>
[Thu Feb 10 12:59:06 2022] dump_stack_lvl+0x5d/0x78
[Thu Feb 10 12:59:06 2022] print_address_description.constprop.0+0x24/0x150
[Thu Feb 10 12:59:06 2022] ? rcu_cblist_dequeue+0x32/0x60
[Thu Feb 10 12:59:06 2022] kasan_report.cold+0x7d/0x117
[Thu Feb 10 12:59:06 2022] ? rcu_cblist_dequeue+0x32/0x60
[Thu Feb 10 12:59:06 2022] __asan_load8+0x86/0xa0
[Thu Feb 10 12:59:06 2022] rcu_cblist_dequeue+0x32/0x60
[Thu Feb 10 12:59:06 2022] rcu_core+0x547/0xca0
[Thu Feb 10 12:59:06 2022] ? call_rcu+0x3c0/0x3c0
[Thu Feb 10 12:59:06 2022] ? __this_cpu_preempt_check+0x13/0x20
[Thu Feb 10 12:59:06 2022] ? lock_is_held_type+0xea/0x140
[Thu Feb 10 12:59:06 2022] rcu_core_si+0xe/0x10
[Thu Feb 10 12:59:06 2022] __do_softirq+0x1d4/0x67b
[Thu Feb 10 12:59:06 2022] __irq_exit_rcu+0x100/0x150
[Thu Feb 10 12:59:06 2022] irq_exit_rcu+0xe/0x30
[Thu Feb 10 12:59:06 2022] sysvec_hyperv_stimer0+0x9d/0xc0
...
[Thu Feb 10 12:59:07 2022] Freed by task 58179:
[Thu Feb 10 12:59:07 2022] kasan_save_stack+0x26/0x50
[Thu Feb 10 12:59:07 2022] kasan_set_track+0x25/0x30
[Thu Feb 10 12:59:07 2022] kasan_set_free_info+0x24/0x40
[Thu Feb 10 12:59:07 2022] ____kasan_slab_free+0x137/0x170
[Thu Feb 10 12:59:07 2022] __kasan_slab_free+0x12/0x20
[Thu Feb 10 12:59:07 2022] slab_free_freelist_hook+0xb3/0x1d0
[Thu Feb 10 12:59:07 2022] kfree+0xcd/0x520
[Thu Feb 10 12:59:07 2022] cifs_smb3_do_mount+0x149/0xbe0 [cifs]
[Thu Feb 10 12:59:07 2022] smb3_get_tree+0x1a0/0x2e0 [cifs]
[Thu Feb 10 12:59:07 2022] vfs_get_tree+0x52/0x140
[Thu Feb 10 12:59:07 2022] path_mount+0x635/0x10c0
[Thu Feb 10 12:59:07 2022] __x64_sys_mount+0x1bf/0x210
[Thu Feb 10 12:59:07 2022] do_syscall_64+0x5c/0xc0
[Thu Feb 10 12:59:07 2022] entry_SYSCALL_64_after_hwframe+0x44/0xae
[Thu Feb 10 12:59:07 2022] Last potentially related work creation:
[Thu Feb 10 12:59:07 2022] kasan_save_stack+0x26/0x50
[Thu Feb 10 12:59:07 2022] __kasan_record_aux_stack+0xb6/0xc0
[Thu Feb 10 12:59:07 2022] kasan_record_aux_stack_noalloc+0xb/0x10
[Thu Feb 10 12:59:07 2022] call_rcu+0x76/0x3c0
[Thu Feb 10 12:59:07 2022] cifs_umount+0xce/0xe0 [cifs]
[Thu Feb 10 12:59:07 2022] cifs_kill_sb+0xc8/0xe0 [cifs]
[Thu Feb 10 12:59:07 2022] deactivate_locked_super+0x5d/0xd0
[Thu Feb 10 12:59:07 2022] cifs_smb3_do_mount+0xab9/0xbe0 [cifs]
[Thu Feb 10 12:59:07 2022] smb3_get_tree+0x1a0/0x2e0 [cifs]
[Thu Feb 10 12:59:07 2022] vfs_get_tree+0x52/0x140
[Thu Feb 10 12:59:07 2022] path_mount+0x635/0x10c0
[Thu Feb 10 12:59:07 2022] __x64_sys_mount+0x1bf/0x210
[Thu Feb 10 12:59:07 2022] do_syscall_64+0x5c/0xc0
[Thu Feb 10 12:59:07 2022] entry_SYSCALL_64_after_hwframe+0x44/0xae
Reported-by: Shyam Prasad N <sprasad@microsoft.com>
Reviewed-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 143de8d97d ]
msg_data_sz return a 32bit value, but size is 16bit. This may lead to a
bit overflow.
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5bfa685e62 ]
It appears that a read access to GIC[DR]_I[CS]PENDRn doesn't always
result in the pending interrupts being accurately reported if they are
mapped to a HW interrupt. This is particularily visible when acking
the timer interrupt and reading the GICR_ISPENDR1 register immediately
after, for example (the interrupt appears as not-pending while it really
is...).
This is because a HW interrupt has its 'active and pending state' kept
in the *physical* distributor, and not in the virtual one, as mandated
by the spec (this is what allows the direct deactivation). The virtual
distributor only caries the pending and active *states* (note the
plural, as these are two independent and non-overlapping states).
Fix it by reading the HW state back, either from the timer itself or
from the distributor if necessary.
Reported-by: Ricardo Koller <ricarkol@google.com>
Tested-by: Ricardo Koller <ricarkol@google.com>
Reviewed-by: Ricardo Koller <ricarkol@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220208123726.3604198-1-maz@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37ef4c19b4 ]
Buttonpads are expected to map the INPUT_PROP_BUTTONPAD property bit
and the BTN_LEFT key bit.
As explained in the specification, where a device has a button type
value of 0 (click-pad) or 1 (pressure-pad) there should not be
discrete buttons:
https://docs.microsoft.com/en-us/windows-hardware/design/component-guidelines/touchpad-windows-precision-touchpad-collection#device-capabilities-feature-report
However, some drivers map the BTN_RIGHT and/or BTN_MIDDLE key bits even
though the device is a buttonpad and therefore does not have those
buttons.
This behavior has forced userspace applications like libinput to
implement different workarounds and quirks to detect buttonpads and
offer to the user the right set of features and configuration options.
For more information:
https://gitlab.freedesktop.org/libinput/libinput/-/merge_requests/726
In order to avoid this issue clear the BTN_RIGHT and BTN_MIDDLE key
bits when the input device is register if the INPUT_PROP_BUTTONPAD
property bit is set.
Notice that this change will not affect udev because it does not check
for buttons. See systemd/src/udev/udev-builtin-input_id.c.
List of known affected hardware:
- Chuwi AeroBook Plus
- Chuwi Gemibook
- Framework Laptop
- GPD Win Max
- Huawei MateBook 2020
- Prestigio Smartbook 141 C2
- Purism Librem 14v1
- StarLite Mk II - AMI firmware
- StarLite Mk II - Coreboot firmware
- StarLite Mk III - AMI firmware
- StarLite Mk III - Coreboot firmware
- StarLabTop Mk IV - AMI firmware
- StarLabTop Mk IV - Coreboot firmware
- StarBook Mk V
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Link: https://lore.kernel.org/r/20220208174806.17183-1-jose.exposito89@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e2a354e37 ]
The check done by regulator_late_cleanup() to detect whether a regulator
is on was inconsistent with the check done by _regulator_is_enabled().
While _regulator_is_enabled() takes the enable GPIO into account,
regulator_late_cleanup() was not doing that.
This resulted in a false positive, e.g. when a GPIO-controlled fixed
regulator was used, which was not enabled at boot time, e.g.
reg_disp_1v2: reg_disp_1v2 {
compatible = "regulator-fixed";
regulator-name = "display_1v2";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
gpio = <&tlmm 148 0>;
enable-active-high;
};
Such regulator doesn't have an is_enabled() operation. Nevertheless
it's state can be determined based on the enable GPIO. The check in
regulator_late_cleanup() wrongly assumed that the regulator is on and
tried to disable it.
Signed-off-by: Oliver Barta <oliver.barta@aptiv.com>
Link: https://lore.kernel.org/r/20220208084645.8686-1-oliver.barta@aptiv.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c33de0673 ]
The current rt5682_jack_detect_handler() assumes the component
and card will always show up and implements an infinite usleep
loop waiting for them to show up.
This does not hold true if a codec interrupt (or other
event) occurs when the card is unbound. The codec driver's
remove or shutdown functions cannot cancel the workqueue due
to the wait loop. As a result, code can either end up blocking
the workqueue, or hit a kernel oops when the card is freed.
Fix the issue by rescheduling the jack detect handler in
case the card is not ready. In case card never shows up,
the shutdown/remove/suspend calls can now cancel the detect
task.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20220207153000.3452802-3-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6d78661dc ]
The current rt5668_jack_detect_handler() assumes the component
and card will always show up and implements an infinite usleep
loop waiting for them to show up.
This does not hold true if a codec interrupt (or other
event) occurs when the card is unbound. The codec driver's
remove or shutdown functions cannot cancel the workqueue due
to the wait loop. As a result, code can either end up blocking
the workqueue, or hit a kernel oops when the card is freed.
Fix the issue by rescheduling the jack detect handler in
case the card is not ready. In case card never shows up,
the shutdown/remove/suspend calls can now cancel the detect
task.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20220207153000.3452802-2-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9495b9b31a ]
The CLKT register contains at poweron 0x40, which at our typical 100kHz
bus rate means .64ms. But there is no specified limit to how long devices
should be able to stretch the clocks, so just disable the timeout. We
still have a timeout wrapping the entire transfer.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
BugLink: https://github.com/raspberrypi/linux/issues/3064
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cacfddf82b ]
In mac80211_hwsim, the probe_req frame is created and sent while
scanning. It is sent with ieee80211_tx_info which is not initialized.
Uninitialized ieee80211_tx_info can cause problems when using
mac80211_hwsim with wmediumd. wmediumd checks the tx_rates field of
ieee80211_tx_info and doesn't relay probe_req frame to other clients
even if it is a broadcasting message.
Call ieee80211_tx_prepare_skb() to initialize ieee80211_tx_info for
the probe_req that is created by hw_scan_work in mac80211_hwsim.
Signed-off-by: JaeMan Park <jaeman@google.com>
Link: https://lore.kernel.org/r/20220113060235.546107-1-jaeman@google.com
[fix memory leak]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c94afc46ca upstream.
memblock.{reserved,memory}.regions may be allocated using kmalloc() in
memblock_double_array(). Use kfree() to release these kmalloced regions
indicated by memblock_{reserved,memory}_in_slab.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Fixes: 3010f87650 ("mm: discard memblock data later")
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d1e972ace4 upstream.
The tegra186 GPIO driver makes the assumption that the pointer
returned by irq_data_get_irq_chip_data() is a pointer to a
tegra_gpio structure. Unfortunately, it is actually a pointer
to the inner gpio_chip structure, as mandated by the gpiolib
infrastructure. Nice try.
The saving grace is that the gpio_chip is the first member of
tegra_gpio, so the bug has gone undetected since... forever.
Fix it by performing a container_of() on the pointer. This results
in no additional code, and makes it possible to understand how
the whole thing works.
Fixes: 5b2b135a87 ("gpio: Add Tegra186 support")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20220211093904.1112679-1-maz@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a2ab75b8e7 upstream.
In the current implementation the user may open a virtual tty which then
could fail to establish the underlying DLCI. The function gsmtty_open()
gets stuck in tty_port_block_til_ready() while waiting for a carrier rise.
This happens if the remote side fails to acknowledge the link establishment
request in time or completely. At some point gsm_dlci_close() is called
to abort the link establishment attempt. The function tries to inform the
associated virtual tty by performing a hangup. But the blocking loop within
tty_port_block_til_ready() is not informed about this event.
The patch proposed here fixes this by resetting the initialization state of
the virtual tty to ensure the loop exits and triggering it to make
tty_port_block_til_ready() return.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220218073123.2121-7-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c19d93542a upstream.
tty flow control is handled via gsmtty_throttle() and gsmtty_unthrottle().
Both functions propagate the outgoing hardware flow control state to the
remote side via MSC (modem status command) frames. The local state is taken
from the RTS (ready to send) flag of the tty. However, RTS gets mapped to
DTR (data terminal ready), which is wrong.
This patch corrects this by mapping RTS to RTS.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220218073123.2121-5-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 96b169f05c upstream.
The here fixed commit made the tty hangup asynchronous to avoid a circular
locking warning. I could not reproduce this warning. Furthermore, due to
the asynchronous hangup the function call now gets queued up while the
underlying tty is being freed. Depending on the timing this results in a
NULL pointer access in the global work queue scheduler. To be precise in
process_one_work(). Therefore, the previous commit made the issue worse
which it tried to fix.
This patch fixes this by falling back to the old behavior which uses a
blocking tty hangup call before freeing up the associated tty.
Fixes: 7030082a74 ("tty: n_gsm: avoid recursive locking with async port hangup")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220218073123.2121-4-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e3b7468f08 upstream.
Trying to open a DLCI by sending a SABM frame may fail with a timeout.
The link is closed on the initiator side without informing the responder
about this event. The responder assumes the link is open after sending a
UA frame to answer the SABM frame. The link gets stuck in a half open
state.
This patch fixes this by initiating the proper link termination procedure
after link setup timeout instead of silently closing it down.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220218073123.2121-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 737b0ef3be upstream.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.6.3.7 describes the encoding of the
control signal octet used by the MSC (modem status command). The same
encoding is also used in convergence layer type 2 as described in chapter
5.5.2. Table 7 and 24 both require the DV (data valid) bit to be set 1 for
outgoing control signal octets sent by the DTE (data terminal equipment),
i.e. for the initiator side.
Currently, the DV bit is only set if CD (carrier detect) is on, regardless
of the side.
This patch fixes this behavior by setting the DV bit on the initiator side
unconditionally.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220218073123.2121-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22e9f71072 upstream.
If the state is not idle then resolve_prepare_src() should immediately
fail and no change to global state should happen. However, it
unconditionally overwrites the src_addr trying to build a temporary any
address.
For instance if the state is already RDMA_CM_LISTEN then this will corrupt
the src_addr and would cause the test in cma_cancel_operation():
if (cma_any_addr(cma_src_addr(id_priv)) && !id_priv->cma_dev)
Which would manifest as this trace from syzkaller:
BUG: KASAN: use-after-free in __list_add_valid+0x93/0xa0 lib/list_debug.c:26
Read of size 8 at addr ffff8881546491e0 by task syz-executor.1/32204
CPU: 1 PID: 32204 Comm: syz-executor.1 Not tainted 5.12.0-rc8-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:79 [inline]
dump_stack+0x141/0x1d7 lib/dump_stack.c:120
print_address_description.constprop.0.cold+0x5b/0x2f8 mm/kasan/report.c:232
__kasan_report mm/kasan/report.c:399 [inline]
kasan_report.cold+0x7c/0xd8 mm/kasan/report.c:416
__list_add_valid+0x93/0xa0 lib/list_debug.c:26
__list_add include/linux/list.h:67 [inline]
list_add_tail include/linux/list.h:100 [inline]
cma_listen_on_all drivers/infiniband/core/cma.c:2557 [inline]
rdma_listen+0x787/0xe00 drivers/infiniband/core/cma.c:3751
ucma_listen+0x16a/0x210 drivers/infiniband/core/ucma.c:1102
ucma_write+0x259/0x350 drivers/infiniband/core/ucma.c:1732
vfs_write+0x28e/0xa30 fs/read_write.c:603
ksys_write+0x1ee/0x250 fs/read_write.c:658
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xae
This is indicating that an rdma_id_private was destroyed without doing
cma_cancel_listens().
Instead of trying to re-use the src_addr memory to indirectly create an
any address derived from the dst build one explicitly on the stack and
bind to that as any other normal flow would do. rdma_bind_addr() will copy
it over the src_addr once it knows the state is valid.
This is similar to commit bc0bdc5afa ("RDMA/cma: Do not change
route.addr.src_addr.ss_family")
Link: https://lore.kernel.org/r/0-v2-e975c8fd9ef2+11e-syz_cma_srcaddr_jgg@nvidia.com
Cc: stable@vger.kernel.org
Fixes: 732d41c545 ("RDMA/cma: Make the locking for automatic state transition more clear")
Reported-by: syzbot+c94a3675a626f6333d74@syzkaller.appspotmail.com
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 243a1dd7ba upstream.
The -ENODEV return value from xhci_check_args() is incorrectly changed
to -EINVAL in a couple places before propagated further.
xhci_check_args() returns 4 types of value, -ENODEV, -EINVAL, 1 and 0.
xhci_urb_enqueue and xhci_check_streams_endpoint return -EINVAL if
the return value of xhci_check_args <= 0.
This causes problems for example r8152_submit_rx, calling usb_submit_urb
in drivers/net/usb/r8152.c.
r8152_submit_rx will never get -ENODEV after submiting an urb when xHC
is halted because xhci_urb_enqueue returns -EINVAL in the very beginning.
[commit message and header edit -Mathias]
Fixes: 203a86613f ("xhci: Avoid NULL pointer deref when host dies.")
Cc: stable@vger.kernel.org
Signed-off-by: Hongyu Xie <xiehongyu1@kylinos.cn>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220215123320.1253947-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84918a89d6 upstream.
The interrupt service routine registered for the gadget is a primary
handler which mask the interrupt source and a threaded handler which
handles the source of the interrupt. Since the threaded handler is
voluntary threaded, the IRQ-core does not disable bottom halves before
invoke the handler like it does for the forced-threaded handler.
Due to changes in networking it became visible that a network gadget's
completions handler may schedule a softirq which remains unprocessed.
The gadget's completion handler is usually invoked either in hard-IRQ or
soft-IRQ context. In this context it is enough to just raise the softirq
because the softirq itself will be handled once that context is left.
In the case of the voluntary threaded handler, there is nothing that
will process pending softirqs. Which means it remain queued until
another random interrupt (on this CPU) fires and handles it on its exit
path or another thread locks and unlocks a lock with the bh suffix.
Worst case is that the CPU goes idle and the NOHZ complains about
unhandled softirqs.
Disable bottom halves before acquiring the lock (and disabling
interrupts) and enable them after dropping the lock. This ensures that
any pending softirqs will handled right away.
Link: https://lkml.kernel.org/r/c2a64979-73d1-2c22-e048-c275c9f81558@samsung.com
Fixes: e5f68b4a3e ("Revert "usb: dwc3: gadget: remove unnecessary _irqsave()"")
Cc: stable <stable@kernel.org>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/Yg/YPejVQH3KkRVd@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 62e3f0afe2 upstream.
When the Bay Trail phy GPIO mappings where added cs and reset were swapped,
this did not cause any issues sofar, because sofar they were always driven
high/low at the same time.
Note the new mapping has been verified both in /sys/kernel/debug/gpio
output on Android factory images on multiple devices, as well as in
the schematics for some devices.
Fixes: 5741022cbd ("usb: dwc3: pci: Add GPIO lookup table on platforms without ACPI GPIO resources")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220213130524.18748-3-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32fde84362 upstream.
When the gadget driver hasn't been (yet) configured, and the cable is
connected to a HOST, the SFTDISCON gets cleared unconditionally, so the
HOST tries to enumerate it.
At the host side, this can result in a stuck USB port or worse. When
getting lucky, some dmesg can be observed at the host side:
new high-speed USB device number ...
device descriptor read/64, error -110
Fix it in drd, by checking the enabled flag before calling
dwc2_hsotg_core_connect(). It will be called later, once configured,
by the normal flow:
- udc_bind_to_driver
- usb_gadget_connect
- dwc2_hsotg_pullup
- dwc2_hsotg_core_connect
Fixes: 17f934024e ("usb: dwc2: override PHY input signals with usb role switch support")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/1644999135-13478-1-git-send-email-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d093e02e8 upstream.
The HPT371 chip physically has only one channel, the secondary one,
however the primary channel registers do exist! Thus we have to
manually disable the non-existing channel if the BIOS hasn't done this
already. Similarly to the pata_hpt3x2n driver, always disable the
primary channel.
Fixes: 669a5db411 ("[libata] Add a bunch of PATA drivers.")
Cc: stable@vger.kernel.org
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eebb0f4e89 upstream.
UART drivers are meant to use the port spinlock within certain
methods, to protect against reentrancy. The sc16is7xx driver does
very little locking, presumably because when added it triggers
"scheduling while atomic" errors. This is due to the use of mutexes
within the regmap abstraction layer, and the mutex implementation's
habit of sleeping the current thread while waiting for access.
Unfortunately this lack of interlocking can lead to corruption of
outbound data, which occurs when the buffer used for I2C transmission
is used simultaneously by two threads - a work queue thread running
sc16is7xx_tx_proc, and an IRQ thread in sc16is7xx_port_irq, both
of which can call sc16is7xx_handle_tx.
An earlier patch added efr_lock, a mutex that controls access to the
EFR register. This mutex is already claimed in the IRQ handler, and
all that is required is to claim the same mutex in sc16is7xx_tx_proc.
See: https://github.com/raspberrypi/linux/issues/4885
Fixes: 6393ff1c44 ("sc16is7xx: Use threaded IRQ")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Link: https://lore.kernel.org/r/20220216160802.1026013-1-phil@raspberrypi.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 632fe0bb8c upstream.
The pm_runtime_enable will increase power disable depth.
If the probe fails, we should use pm_runtime_disable() to balance
pm_runtime_enable(). In the PM Runtime docs:
Drivers in ->remove() callback should undo the runtime PM changes done
in ->probe(). Usually this means calling pm_runtime_disable(),
pm_runtime_dont_use_autosuspend() etc.
We should do this in error handling.
Fix this problem for the following drivers: bmc150, bmg160, kmx61,
kxcj-1013, mma9551, mma9553.
Fixes: 7d0ead5c3f ("iio: Reconcile operation order between iio_register/unregister and pm functions")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220106112309.16879-1-linmq006@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 84ec758fb2 ]
When configfs_register_subsystem() or configfs_unregister_subsystem()
is executing link_group() or unlink_group(),
it is possible that two processes add or delete list concurrently.
Some unfortunate interleavings of them can cause kernel panic.
One of cases is:
A --> B --> C --> D
A <-- B <-- C <-- D
delete list_head *B | delete list_head *C
--------------------------------|-----------------------------------
configfs_unregister_subsystem | configfs_unregister_subsystem
unlink_group | unlink_group
unlink_obj | unlink_obj
list_del_init | list_del_init
__list_del_entry | __list_del_entry
__list_del | __list_del
// next == C |
next->prev = prev |
| next->prev = prev
prev->next = next |
| // prev == B
| prev->next = next
Fix this by adding mutex when calling link_group() or unlink_group(),
but parent configfs_subsystem is NULL when config_item is root.
So I create a mutex configfs_subsystem_mutex.
Fixes: 7063fbf226 ("[PATCH] configfs: User-driven configuration filesystem")
Signed-off-by: ChenXiaoSong <chenxiaosong2@huawei.com>
Signed-off-by: Laibin Qiu <qiulaibin@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c46fa8911b ]
Error path of rtrs_clt_open() calls free_clt(), where free_permit is
called. This is wrong since error path of rtrs_clt_open() does not need
to call free_permit().
Also, moving free_permits() call to rtrs_clt_close(), makes it more
aligned with the call to alloc_permit() in rtrs_clt_open().
Fixes: 6a98d71dae ("RDMA/rtrs: client: main functionality")
Link: https://lore.kernel.org/r/20220217030929.323849-2-haris.iqbal@ionos.com
Signed-off-by: Md Haris Iqbal <haris.iqbal@ionos.com>
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8700af2cc1 ]
Callback function rtrs_clt_dev_release() for put_device() calls kfree(clt)
to free memory. We shouldn't call kfree(clt) again, and we can't use the
clt after kfree too.
Replace device_register() with device_initialize() and device_add() so that
dev_set_name can() be used appropriately.
Move mutex_destroy() to the release function so it can be called in
the alloc_clt err path.
Fixes: eab0982466 ("RDMA/rtrs-clt: Refactor the failure cases in alloc_clt")
Link: https://lore.kernel.org/r/20220217030929.323849-1-haris.iqbal@ionos.com
Reported-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Md Haris Iqbal <haris.iqbal@ionos.com>
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d04ad245d6 ]
With the existing logic where clear_ack is true (HW doesn’t support
auto clear for ICR), interrupt clear register reset is not handled
properly. Due to this only the first interrupts get processed properly
and further interrupts are blocked due to not resetting interrupt
clear register.
Example for issue case where Invert_ack is false and clear_ack is true:
Say Default ISR=0x00 & ICR=0x00 and ISR is triggered with 2
interrupts making ISR = 0x11.
Step 1: Say ISR is set 0x11 (store status_buff = ISR). ISR needs to
be cleared with the help of ICR once the Interrupt is processed.
Step 2: Write ICR = 0x11 (status_buff), this will clear the ISR to 0x00.
Step 3: Issue - In the existing code, ICR is written with ICR =
~(status_buff) i.e ICR = 0xEE -> This will block all the interrupts
from raising except for interrupts 0 and 4. So expectation here is to
reset ICR, which will unblock all the interrupts.
if (chip->clear_ack) {
if (chip->ack_invert && !ret)
........
else if (!ret)
ret = regmap_write(map, reg,
~data->status_buf[i]);
So writing 0 and 0xff (when ack_invert is true) should have no effect, other
than clearing the ACKs just set.
Fixes: 3a6f0fb7b8 ("regmap: irq: Add support to clear ack registers")
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20220217085007.30218-1-quic_pkumpatl@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab3824427b ]
In zynq_qspi_exec_mem_op(), kzalloc() is directly used in memset(),
which could lead to a NULL pointer dereference on failure of
kzalloc().
Fix this bug by adding a check of tmpbuf.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_SPI_ZYNQ_QSPI=m show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: 67dca5e580 ("spi: spi-mem: Add support for Zynq QSPI controller")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Link: https://lore.kernel.org/r/20211130172253.203700-1-zhou1615@umn.edu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7eaf1f37b8 upstream.
For RX TLS device-offloaded packets, the HW spec guarantees checksum
validation for the offloaded packets, but does not define whether the
CQE.checksum field matches the original packet (ciphertext) or
the decrypted one (plaintext). This latitude allows architetctural
improvements between generations of chips, resulting in different decisions
regarding the value type of CQE.checksum.
Hence, for these packets, the device driver should not make use of this CQE
field. Here we block CHECKSUM_COMPLETE usage for RX TLS device-offloaded
packets, and use CHECKSUM_UNNECESSARY instead.
Value of the packet's tcp_hdr.csum is not modified by the HW, and it always
matches the original ciphertext.
Fixes: 1182f36593 ("net/mlx5e: kTLS, Add kTLS RX HW offload support")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07666c75ad upstream.
Match metadata support check returns false for ecpf device.
However, this support does exist for ecpf and therefore this
limitation should be removed to allow feature such as stacked
devices and internal port offloaded to be supported.
Fixes: 92ab1eb392 ("net/mlx5: E-Switch, Enable vport metadata matching if firmware supports it")
Signed-off-by: Ariel Levkovich <lariel@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b645e57deb upstream.
Add missing call to up_write_ref_node() which releases the semaphore
in case the FTE doesn't have destinations, such in drop rule case.
Fixes: 465e7baab6 ("net/mlx5: Fix deletion of duplicate rules")
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de7b2efacf upstream.
This test is checking if we exited the list via break or not. However
if it did not exit via a break then "node" does not point to a valid
udp_tunnel_nic_shared_node struct. It will work because of the way
the structs are laid out it's the equivalent of
"if (info->shared->udp_tunnel_nic_info != dev)" which will always be
true, but it's not the right way to test.
Fixes: 74cc6d182d ("udp_tunnel: add the ability to share port tables")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dad3bdeef4 upstream.
stateful objects can be updated from the control plane.
The transaction logic allocates a temporary object for this purpose.
The ->init function was called for this object, so plain kfree() leaks
resources. We must call ->destroy function of the object.
nft_obj_destroy does this, but it also decrements the module refcount,
but the update path doesn't increment it.
To avoid special-casing the update object release, do module_get for
the update case too and release it via nft_obj_destroy().
Fixes: d62d0ba97b ("netfilter: nf_tables: Introduce stateful object update operation")
Cc: Fernando Fernandez Mancera <ffmancera@riseup.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b352c3465b upstream.
devm_kmalloc() returns a pointer to allocated memory on success, NULL
on failure. While lp->indirect_lock is allocated by devm_kmalloc()
without proper check. It is better to check the value of it to
prevent potential wrong memory access.
Fixes: f14f5c11f0 ("net: ll_temac: Support indirect_mutex share within TEMAC IP")
Signed-off-by: Xiaoke Wang <xkernel.wang@foxmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f131de361 upstream.
Flow table lookup is skipped if packet either went through ct clear
action (which set the IP_CT_UNTRACKED flag on the packet), or while
switching zones and there is already a connection associated with
the packet. This will result in no SW offload of the connection,
and the and connection not being removed from flow table with
TCP teardown (fin/rst packet).
To fix the above, remove these unneccary checks in flow
table lookup.
Fixes: 46475bb20f ("net/sched: act_ct: Software offload of established flows")
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ecbd4912a6 upstream.
In order to fill the drm_display_info structure each time an EDID is
read, the code currently will call drm_add_display_info with the parsed
EDID.
drm_add_display_info will then call drm_reset_display_info to reset all
the fields to 0, and then set them to the proper value depending on the
EDID.
In the color_formats case, we will thus report that we don't support any
color format, and then fill it back with RGB444 plus the additional
formats described in the EDID Feature Support byte.
However, since that byte only contains format-related bits since the 1.4
specification, this doesn't happen if the EDID is following an earlier
specification. In turn, it means that for one of these EDID, we end up
with color_formats set to 0.
The EDID 1.3 specification never really specifies what it means by RGB
exactly, but since both HDMI and DVI will use RGB444, it's fairly safe
to assume it's supposed to be RGB444.
Let's move the addition of RGB444 to color_formats earlier in
drm_add_display_info() so that it's always set for a digital display.
Fixes: da05a5a71a ("drm: parse color format support for digital displays")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reported-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220203115416.1137308-1-maxime@cerno.tech
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc20cced05 upstream.
We encounter a tcp drop issue in our cloud environment. Packet GROed in
host forwards to a VM virtio_net nic with net_failover enabled. VM acts
as a IPVS LB with ipip encapsulation. The full path like:
host gro -> vm virtio_net rx -> net_failover rx -> ipvs fullnat
-> ipip encap -> net_failover tx -> virtio_net tx
When net_failover transmits a ipip pkt (gso_type = 0x0103, which means
SKB_GSO_TCPV4, SKB_GSO_DODGY and SKB_GSO_IPXIP4), there is no gso
did because it supports TSO and GSO_IPXIP4. But network_header points to
inner ip header.
Call Trace:
tcp4_gso_segment ------> return NULL
inet_gso_segment ------> inner iph, network_header points to
ipip_gso_segment
inet_gso_segment ------> outer iph
skb_mac_gso_segment
Afterwards virtio_net transmits the pkt, only inner ip header is modified.
And the outer one just keeps unchanged. The pkt will be dropped in remote
host.
Call Trace:
inet_gso_segment ------> inner iph, outer iph is skipped
skb_mac_gso_segment
__skb_gso_segment
validate_xmit_skb
validate_xmit_skb_list
sch_direct_xmit
__qdisc_run
__dev_queue_xmit ------> virtio_net
dev_hard_start_xmit
__dev_queue_xmit ------> net_failover
ip_finish_output2
ip_output
iptunnel_xmit
ip_tunnel_xmit
ipip_tunnel_xmit ------> ipip
dev_hard_start_xmit
__dev_queue_xmit
ip_finish_output2
ip_output
ip_forward
ip_rcv
__netif_receive_skb_one_core
netif_receive_skb_internal
napi_gro_receive
receive_buf
virtnet_poll
net_rx_action
The root cause of this issue is specific with the rare combination of
SKB_GSO_DODGY and a tunnel device that adds an SKB_GSO_ tunnel option.
SKB_GSO_DODGY is set from external virtio_net. We need to reset network
header when callbacks.gso_segment() returns NULL.
This patch also includes ipv6_gso_segment(), considering SIT, etc.
Fixes: cb32f511a7 ("ipip: add GSO/TSO support")
Signed-off-by: Tao Liu <thomas.liu@ucloud.cn>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a1f8fec4da upstream.
These tests are supposed to check if the loop exited via a break or not.
However the tests are wrong because if we did not exit via a break then
"p" is not a valid pointer. In that case, it's the equivalent of
"if (*(u32 *)sr == *last_key) {". That's going to work most of the time,
but there is a potential for those to be equal.
Fixes: 1593123a6a ("tipc: add name table dump to new netlink api")
Fixes: 1a1a143daf ("tipc: add publication dump to new netlink api")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 75134f16e7 upstream.
syzbot reported various soft lockups caused by bpf batch operations.
INFO: task kworker/1:1:27 blocked for more than 140 seconds.
INFO: task hung in rcu_barrier
Nothing prevents batch ops to process huge amount of data,
we need to add schedule points in them.
Note that maybe_wait_bpf_programs(map) calls from
generic_map_delete_batch() can be factorized by moving
the call after the loop.
This will be done later in -next tree once we get this fix merged,
unless there is strong opinion doing this optimization sooner.
Fixes: aa2e93b8e5 ("bpf: Add generic support for update and delete batch ops")
Fixes: cb4d03ab49 ("bpf: Add generic support for lookup batch op")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Brian Vazquez <brianvv@google.com>
Link: https://lore.kernel.org/bpf/20220217181902.808742-1-eric.dumazet@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a11678f68 upstream.
If bpf_msg_push_data() is called with len 0 (as it happens during
selftests/bpf/test_sockmap), we do not need to do anything and can
return early.
Calling bpf_msg_push_data() with len 0 previously lead to a wrong ENOMEM
error: we later called get_order(copy + len); if len was 0, copy + len
was also often 0 and get_order() returned some undefined value (at the
moment 52). alloc_pages() caught that and failed, but then bpf_msg_push_data()
returned ENOMEM. This was wrong because we are most probably not out of
memory and actually do not need any additional memory.
Fixes: 6fff607e2f ("bpf: sk_msg program helper bpf_msg_push_data")
Signed-off-by: Felix Maurer <fmaurer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/df69012695c7094ccb1943ca02b4920db3537466.1644421921.git.fmaurer@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b5f517cca upstream.
If an attempt is made to a sensor with a thermal zone and it fails,
the call to devm_thermal_zone_of_sensor_register() may return -ENODEV.
This may result in crashes similar to the following.
Unable to handle kernel NULL pointer dereference at virtual address 00000000000003cd
...
Internal error: Oops: 96000021 [#1] PREEMPT SMP
...
pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : mutex_lock+0x18/0x60
lr : thermal_zone_device_update+0x40/0x2e0
sp : ffff800014c4fc60
x29: ffff800014c4fc60 x28: ffff365ee3f6e000 x27: ffffdde218426790
x26: ffff365ee3f6e000 x25: 0000000000000000 x24: ffff365ee3f6e000
x23: ffffdde218426870 x22: ffff365ee3f6e000 x21: 00000000000003cd
x20: ffff365ee8bf3308 x19: ffffffffffffffed x18: 0000000000000000
x17: ffffdde21842689c x16: ffffdde1cb7a0b7c x15: 0000000000000040
x14: ffffdde21a4889a0 x13: 0000000000000228 x12: 0000000000000000
x11: 0000000000000000 x10: 0000000000000000 x9 : 0000000000000000
x8 : 0000000001120000 x7 : 0000000000000001 x6 : 0000000000000000
x5 : 0068000878e20f07 x4 : 0000000000000000 x3 : 00000000000003cd
x2 : ffff365ee3f6e000 x1 : 0000000000000000 x0 : 00000000000003cd
Call trace:
mutex_lock+0x18/0x60
hwmon_notify_event+0xfc/0x110
0xffffdde1cb7a0a90
0xffffdde1cb7a0b7c
irq_thread_fn+0x2c/0xa0
irq_thread+0x134/0x240
kthread+0x178/0x190
ret_from_fork+0x10/0x20
Code: d503201f d503201f d2800001 aa0103e4 (c8e47c02)
Jon Hunter reports that the exact call sequence is:
hwmon_notify_event()
--> hwmon_thermal_notify()
--> thermal_zone_device_update()
--> update_temperature()
--> mutex_lock()
The hwmon core needs to handle all errors returned from calls
to devm_thermal_zone_of_sensor_register(). If the call fails
with -ENODEV, report that the sensor was not attached to a
thermal zone but continue to register the hwmon device.
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Cc: Dmitry Osipenko <digetx@gmail.com>
Fixes: 1597b374af ("hwmon: Add notification support")
Reviewed-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84d3c83e6e upstream.
ethtool --show-fec <interface> does not show anything when the Active
FEC setting in the chip is set to None. Fix it to properly return
ETHTOOL_FEC_OFF in that case.
Fixes: 8b2775890a ("bnxt_en: Report FEC settings to ethtool.")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aceeafefff upstream.
Adds a driver private tee_context by moving the tee_context in struct
optee_notif to struct optee. This tee_context was previously used when
doing internal calls to secure world to deliver notification.
The new driver internal tee_context is now also when allocating driver
private shared memory. This decouples the shared memory object from its
original tee_context. This is needed when the life time of such a memory
allocation outlives the client tee_context.
This patch fixes the problem described below:
The addition of a shutdown hook by commit f25889f931 ("optee: fix tee out
of memory failure seen during kexec reboot") introduced a kernel shutdown
regression that can be triggered after running the OP-TEE xtest suites.
Once the shutdown hook is called it is not possible to communicate any more
with the supplicant process because the system is not scheduling task any
longer. Thus if the optee driver shutdown path receives a supplicant RPC
request from the OP-TEE we will deadlock the kernel's shutdown.
Fixes: f25889f931 ("optee: fix tee out of memory failure seen during kexec reboot")
Fixes: 217e0250cc ("tee: use reference counting for tee_context")
Reported-by: Lars Persson <larper@axis.com>
Cc: stable@vger.kernel.org
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
[JW: backport to 5.10-stable + update commit message]
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e2c3ef049 upstream.
Exports the two functions teedev_open() and teedev_close_context() in
order to make it easier to create a driver internal struct tee_context.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When eagerly switching PKRU in switch_fpu_finish() it checks that
current is not a kernel thread as kernel threads will never use PKRU.
It's possible that this_cpu_read_stable() on current_task
(ie. get_current()) is returning an old cached value. To resolve this
reference next_p directly rather than relying on current.
As written it's possible when switching from a kernel thread to a
userspace thread to observe a cached PF_KTHREAD flag and never restore
the PKRU. And as a result this issue only occurs when switching
from a kernel thread to a userspace thread, switching from a non kernel
thread works perfectly fine because all that is considered in that
situation are the flags from some other non kernel task and the next fpu
is passed in to switch_fpu_finish().
This behavior only exists between 5.2 and 5.13 when it was fixed by a
rewrite decoupling PKRU from xstate, in:
commit 954436989c ("x86/fpu: Remove PKRU handling from switch_fpu_finish()")
Unfortunately backporting the fix from 5.13 is probably not realistic as
it's part of a 60+ patch series which rewrites most of the PKRU handling.
Fixes: 0cecca9d03 ("x86/fpu: Eager switch PKRU state")
Signed-off-by: Brian Geffon <bgeffon@google.com>
Signed-off-by: Willis Kung <williskung@google.com>
Tested-by: Willis Kung <williskung@google.com>
Cc: <stable@vger.kernel.org> # v5.4.x
Cc: <stable@vger.kernel.org> # v5.10.x
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1a5983f56 upstream.
immediate verdict expression needs to allocate one slot in the flow offload
action array, however, immediate data expression does not need to do so.
fwd and dup expression need to allocate one slot, this is missing.
Add a new offload_action interface to report if this expression needs to
allocate one slot in the flow offload action array.
Fixes: be2861dc36 ("netfilter: nft_{fwd,dup}_netdev: add offload support")
Reported-and-tested-by: Nick Gregory <Nick.Gregory@Sophos.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d2b1a1ec9 upstream.
A broken device may give an extreme offset like 0xFFF0
and a reasonable length for a fragment. In the sanity
check as formulated now, this will create an integer
overflow, defeating the sanity check. Both offset
and offset + len need to be checked in such a manner
that no overflow can occur.
And those quantities should be unsigned.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f3c1fc53d upstream.
In current async pagefault logic, when a page is ready, KVM relies on
kvm_arch_can_dequeue_async_page_present() to determine whether to deliver
a READY event to the Guest. This function test token value of struct
kvm_vcpu_pv_apf_data, which must be reset to zero by Guest kernel when a
READY event is finished by Guest. If value is zero meaning that a READY
event is done, so the KVM can deliver another.
But the kvm_arch_setup_async_pf() may produce a valid token with zero
value, which is confused with previous mention and may lead the loss of
this READY event.
This bug may cause task blocked forever in Guest:
INFO: task stress:7532 blocked for more than 1254 seconds.
Not tainted 5.10.0 #16
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:stress state:D stack: 0 pid: 7532 ppid: 1409
flags:0x00000080
Call Trace:
__schedule+0x1e7/0x650
schedule+0x46/0xb0
kvm_async_pf_task_wait_schedule+0xad/0xe0
? exit_to_user_mode_prepare+0x60/0x70
__kvm_handle_async_pf+0x4f/0xb0
? asm_exc_page_fault+0x8/0x30
exc_page_fault+0x6f/0x110
? asm_exc_page_fault+0x8/0x30
asm_exc_page_fault+0x1e/0x30
RIP: 0033:0x402d00
RSP: 002b:00007ffd31912500 EFLAGS: 00010206
RAX: 0000000000071000 RBX: ffffffffffffffff RCX: 00000000021a32b0
RDX: 000000000007d011 RSI: 000000000007d000 RDI: 00000000021262b0
RBP: 00000000021262b0 R08: 0000000000000003 R09: 0000000000000086
R10: 00000000000000eb R11: 00007fefbdf2baa0 R12: 0000000000000000
R13: 0000000000000002 R14: 000000000007d000 R15: 0000000000001000
Signed-off-by: Liang Zhang <zhangliang5@huawei.com>
Message-Id: <20220222031239.1076682-1-zhangliang5@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a972798368 upstream.
Fix 3 bugs:
a) emulate_stw() doesn't return the error code value, so faulting
instructions are not reported and aborted.
b) Tell emulate_ldw() to handle fldw_l as floating point instruction
c) Tell emulate_ldw() to handle ldw_m as integer instruction
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd2288f4a0 upstream.
Usually the kernel provides fixup routines to emulate the fldd and fstd
floating-point instructions if they load or store 8-byte from/to a not
natuarally aligned memory location.
On a 32-bit kernel I noticed that those unaligned handlers didn't worked and
instead the application got a SEGV.
While checking the code I found two problems:
First, the OPCODE_FLDD_L and OPCODE_FSTD_L cases were ifdef'ed out by the
CONFIG_PA20 option, and as such those weren't built on a pure 32-bit kernel.
This is now fixed by moving the CONFIG_PA20 #ifdef to prevent the compilation
of OPCODE_LDD_L and OPCODE_FSTD_L only, and handling the fldd and fstd
instructions.
The second problem are two bugs in the 32-bit inline assembly code, where the
wrong registers where used. The calculation of the natural alignment used %2
(vall) instead of %3 (ior), and the first word was stored back to address %1
(valh) instead of %3 (ior).
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a58da53ffd upstream.
vhost_vsock_stop() calls vhost_dev_check_owner() to check the device
ownership. It expects current->mm to be valid.
vhost_vsock_stop() is also called by vhost_vsock_dev_release() when
the user has not done close(), so when we are in do_exit(). In this
case current->mm is invalid and we're releasing the device, so we
should clean it anyway.
Let's check the owner only when vhost_vsock_stop() is called
by an ioctl.
When invoked from release we can not fail so we don't check return
code of vhost_vsock_stop(). We need to stop vsock even if it's not
the owner.
Fixes: 433fc58e6b ("VSOCK: Introduce vhost_vsock.ko")
Cc: stable@vger.kernel.org
Reported-by: syzbot+1e3ea63db39f2b4440e0@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+3140b17cb44a7b174008@syzkaller.appspotmail.com
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea1d1ca402 upstream.
Check item size before accessing the device item to avoid out of bound
access, similar to inode_item check.
Signed-off-by: Su Yue <l@damenly.su>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05c7b7a92c upstream.
As previously discussed(https://lkml.org/lkml/2022/1/20/51),
cpuset_attach() is affected with similar cpu hotplug race,
as follow scenario:
cpuset_attach() cpu hotplug
--------------------------- ----------------------
down_write(cpuset_rwsem)
guarantee_online_cpus() // (load cpus_attach)
sched_cpu_deactivate
set_cpu_active()
// will change cpu_active_mask
set_cpus_allowed_ptr(cpus_attach)
__set_cpus_allowed_ptr_locked()
// (if the intersection of cpus_attach and
cpu_active_mask is empty, will return -EINVAL)
up_write(cpuset_rwsem)
To avoid races such as described above, protect cpuset_attach() call
with cpu_hotplug_lock.
Fixes: be367d0992 ("cgroups: let ss->can_attach and ss->attach do whole threadgroups at a time")
Cc: stable@vger.kernel.org # v2.6.32+
Reported-by: Zhao Gongyi <zhaogongyi@huawei.com>
Signed-off-by: Zhang Qiao <zhangqiao22@huawei.com>
Acked-by: Waiman Long <longman@redhat.com>
Reviewed-by: Michal Koutný <mkoutny@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28df029d53 upstream.
A kernel exception was hit when trying to dump /proc/lockdep_chains after
lockdep report "BUG: MAX_LOCKDEP_CHAIN_HLOCKS too low!":
Unable to handle kernel paging request at virtual address 00054005450e05c3
...
00054005450e05c3] address between user and kernel address ranges
...
pc : [0xffffffece769b3a8] string+0x50/0x10c
lr : [0xffffffece769ac88] vsnprintf+0x468/0x69c
...
Call trace:
string+0x50/0x10c
vsnprintf+0x468/0x69c
seq_printf+0x8c/0xd8
print_name+0x64/0xf4
lc_show+0xb8/0x128
seq_read_iter+0x3cc/0x5fc
proc_reg_read_iter+0xdc/0x1d4
The cause of the problem is the function lock_chain_get_class() will
shift lock_classes index by 1, but the index don't need to be shifted
anymore since commit 01bb6f0af9 ("locking/lockdep: Change the range
of class_idx in held_lock struct") already change the index to start
from 0.
The lock_classes[-1] located at chain_hlocks array. When printing
lock_classes[-1] after the chain_hlocks entries are modified, the
exception happened.
The output of lockdep_chains are incorrect due to this problem too.
Fixes: f611e8cf98 ("lockdep: Take read/write status in consideration when generate chainkey")
Signed-off-by: Cheng Jui Wang <cheng-jui.wang@mediatek.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Boqun Feng <boqun.feng@gmail.com>
Link: https://lore.kernel.org/r/20220210105011.21712-1-cheng-jui.wang@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 834cea3a25 upstream.
DSL and CM (Cable Modem) support 8 B max transfer size and have a custom
DT binding for that reason. This driver was checking for a wrong
"compatible" however which resulted in an incorrect setup.
Fixes: e2e5a2c618 ("i2c: brcmstb: Adding support for CM and DSL SoCs")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 02a4a69667 upstream.
There is a minor chance for a race, if a pointer to an i2c-bus subnode
is stored and then reused after releasing its reference, and it would
be sufficient to get one more reference under a loop over children
subnodes.
Fixes: e517526195 ("i2c: Add Qualcomm CCI I2C driver")
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a0d48505a1 upstream.
If i2c_add_adapter() fails to add an I2C adapter found on QCOM CCI
controller, on error path i2c_del_adapter() is still called.
Fortunately there is a sanity check in the I2C core, so the only
visible implication is a printed debug level message:
i2c-core: attempting to delete unregistered adapter [Qualcomm-CCI]
Nevertheless it would be reasonable to correct the probe error path.
Fixes: e517526195 ("i2c: Add Qualcomm CCI I2C driver")
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f8efca92ae upstream.
Do alignment logic properly and use the "ptr" local variable for
calculating the remainder of the alignment.
This became an issue because struct edac_mc_layer has a size that is not
zero modulo eight, and the next offset that was prepared for the private
data was unaligned, causing an alignment exception.
The patch in Fixes: which broke this actually wanted to "what we
actually care about is the alignment of the actual pointer that's about
to be returned." But it didn't check that alignment.
Use the correct variable "ptr" for that.
[ bp: Massage commit message. ]
Fixes: 8447c4d15e ("edac: Do alignment logic properly in edac_align_ptr()")
Signed-off-by: Eliav Farber <farbere@amazon.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220113100622.12783-2-farbere@amazon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f4c5a26f7 upstream.
When connected point to point, the driver does not know the FC4's supported
by the other end. In Fabrics, it can query the nameserver. Thus the driver
must send PRLIs for the FC4s it supports and enable support based on the
acc(ept) or rej(ect) of the respective FC4 PRLI. Currently the driver
supports SCSI and NVMe PRLIs.
Unfortunately, although the behavior is per standard, many devices have
come to expect only SCSI PRLIs. In this particular example, the NVMe PRLI
is properly RJT'd but the target decided that it must LOGO after seeing the
unexpected NVMe PRLI. The LOGO causes the sequence to restart and login is
now in an infinite failure loop.
Fix the problem by having the driver, on a pt2pt link, remember NVMe PRLI
accept or reject status across logout as long as the link stays "up". When
retrying login, if the prior NVMe PRLI was rejected, it will not be sent on
the next login.
Link: https://lore.kernel.org/r/20220212163120.15385-1-jsmart2021@gmail.com
Cc: <stable@vger.kernel.org> # v5.4+
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1b9e740a81 ]
When the KCONFIG_AUTOCONFIG is specified (e.g. export \
KCONFIG_AUTOCONFIG=output/config/auto.conf), the directory of
include/config/ will not be created, so kconfig can't create deps
files in it and auto.conf can't be generated.
Signed-off-by: Jing Leng <jleng@ambarella.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37f7860602 ]
Single page and coherent memory blocks can use different DMA masks
when the macb accesses physical memory directly. The kernel is clever
enough to allocate pages that fit into the requested address width.
When using the ARM SMMU, the DMA mask must be the same for single
pages and big coherent memory blocks. Otherwise the translation
tables turn into one big mess.
[ 74.959909] macb ff0e0000.ethernet eth0: DMA bus error: HRESP not OK
[ 74.959989] arm-smmu fd800000.smmu: Unhandled context fault: fsr=0x402, iova=0x3165687460, fsynr=0x20001, cbfrsynra=0x877, cb=1
[ 75.173939] macb ff0e0000.ethernet eth0: DMA bus error: HRESP not OK
[ 75.173955] arm-smmu fd800000.smmu: Unhandled context fault: fsr=0x402, iova=0x3165687460, fsynr=0x20001, cbfrsynra=0x877, cb=1
Since using the same DMA mask does not hurt direct 1:1 physical
memory mappings, this commit always aligns DMA and coherent masks.
Signed-off-by: Marc St-Amand <mstamand@ciena.com>
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3203ce39ac ]
The kernel parameter "tp_printk_stop_on_boot" starts with "tp_printk" which is
the same as another kernel parameter "tp_printk". If "tp_printk" setup is
called before the "tp_printk_stop_on_boot", it will override the latter
and keep it from being set.
This is similar to other kernel parameter issues, such as:
Commit 745a600cf1 ("um: console: Ignore console= option")
or init/do_mounts.c:45 (setup function of "ro" kernel param)
Fix it by checking for a "_" right after the "tp_printk" and if that
exists do not process the parameter.
Link: https://lkml.kernel.org/r/20220208195421.969326-1-jsyoo5b@gmail.com
Signed-off-by: JaeSang Yoo <jsyoo5b@gmail.com>
[ Fixed up change log and added space after if condition ]
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9c10b5b3b ]
If there are failures then we must not leave the non-NULL pointers with
the error value, otherwise `rpcrdma_ep_destroy` gets confused and tries
free them, resulting in an Oops.
Signed-off-by: Dan Aloni <dan.aloni@vastdata.com>
Acked-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8ea23d5fa ]
This device is a CF card, or possibly an SSD in CF form factor.
It supports NCQ and high speed DMA.
While it also advertises TRIM support, I/O errors are reported
when the discard mount option fstrim is used. TRIM also fails
when disabling NCQ and not just as an NCQ command.
TRIM must be disabled for this device.
Signed-off-by: Zoltán Böszörményi <zboszor@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a4c5b2a6d ]
The 'shell' built-in only returns the first 256 bytes of the command's
output. In some cases, 'shell' is used to return a path; by bumping up
the buffer size to 4096 this lets us capture up to PATH_MAX.
The specific case where I ran into this was due to commit 1e860048c5
("gcc-plugins: simplify GCC plugin-dev capability test"). After this
change, we now use `$(shell,$(CC) -print-file-name=plugin)` to return
a path; if the gcc path is particularly long, then the path ends up
truncated at the 256 byte mark, which makes the HAVE_GCC_PLUGINS
depends test always fail.
Signed-off-by: Brenda Streiff <brenda.streiff@ni.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e2aa5e650b ]
These are some trivial fixups, which were needed to build the tests with
clang and -Werror. The following issues are fixed:
- Remove various unused variables.
- In child_poll_leader_exit_test, clang isn't smart enough to realize
syscall(SYS_exit, 0) won't return, so it complains we never return
from a non-void function. Add an extra exit(0) to appease it.
- In test_pidfd_poll_leader_exit, ret may be branched on despite being
uninitialized, if we have !use_waitpid. Initialize it to zero to get
the right behavior in that case.
Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Acked-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4cbd93c3c1 ]
When running the pidfd_fdinfo_test on arm64, it fails for me. After some
digging, the reason is that the child exits due to SIGBUS, because it
overflows the 1024 byte stack we've reserved for it.
To fix the issue, increase the stack size to 8192 bytes (this number is
somewhat arbitrary, and was arrived at through experimentation -- I kept
doubling until the failure no longer occurred).
Also, let's make the issue easier to debug. wait_for_pid() returns an
ambiguous value: it may return -1 in all of these cases:
1. waitpid() itself returned -1
2. waitpid() returned success, but we found !WIFEXITED(status).
3. The child process exited, but it did so with a -1 exit code.
There's no way for the caller to tell the difference. So, at least log
which occurred, so the test runner can debug things.
While debugging this, I found that we had !WIFEXITED(), because the
child exited due to a signal. This seems like a reasonably common case,
so also print out whether or not we have WIFSIGNALED(), and the
associated WTERMSIG() (if any). This lets us see the SIGBUS I'm fixing
clearly when it occurs.
Finally, I'm suspicious of allocating the child's stack on our stack.
man clone(2) suggests that the correct way to do this is with mmap(),
and in particular by setting MAP_STACK. So, switch to doing it that way
instead.
Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Acked-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77b337196a ]
Vivek Thrivikraman reported:
An SCTP server application which is accessed continuously by client
application.
When the session disconnects the client retries to establish a connection.
After restart of SCTP server application the session is not established
because of stale conntrack entry with connection state CLOSED as below.
(removing this entry manually established new connection):
sctp 9 CLOSED src=10.141.189.233 [..] [ASSURED]
Just skip timeout update of closed entries, we don't want them to
stay around forever.
Reported-and-tested-by: Vivek Thrivikraman <vivek.thrivikraman@est.tech>
Closes: https://bugzilla.netfilter.org/show_bug.cgi?id=1579
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d4df649cb ]
The thead,c900-plic has been used in opensbi to distinguish
PLIC [1]. Although PLICs have the same behaviors in Linux,
they are different hardware with some custom initializing in
firmware(opensbi).
Qute opensbi patch commit-msg by Samuel:
The T-HEAD PLIC implementation requires setting a delegation bit
to allow access from S-mode. Now that the T-HEAD PLIC has its own
compatible string, set this bit automatically from the PLIC driver,
instead of reaching into the PLIC's MMIO space from another driver.
[1]: 78c2b19218
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Cc: Anup Patel <anup@brainfault.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Samuel Holland <samuel@sholland.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220130135634.1213301-3-guoren@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42fed57046 ]
The PHY client driver does a phy_exit() call on suspend or rmmod and
the PHY driver needs to know the difference because some clocks need
to be kept running for suspend but can be shutdown on unbind/rmmod
(or if there are no PHY clients at all).
The fix is to use a PM notifier so the driver can tell if a PHY
client is calling exit() because of a system suspend or a driver
unbind/rmmod.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211201180653.35097-2-alcooperx@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 34596ba380 ]
This was found by coccicheck:
./arch/arm/mach-omap2/display.c, 272, 1-7, ERROR missing put_device;
call of_find_device_by_node on line 258, but without a corresponding
object release within this function.
Move the put_device() call before the if judgment.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Ye Guojin <ye.guojin@zte.com.cn>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 80c469a0a0 ]
Fix following coccicheck warning:
./arch/arm/mach-omap2/omap_hwmod.c:753:1-23: WARNING: Function
for_each_matching_node should have of_node_put() before break
Early exits from for_each_matching_node should decrement the
node reference counter.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8bfee85f1 ]
AMD's event select is 3 nybbles, with the high nybble in bits 35:32 of
a PerfEvtSeln MSR. Don't drop the high nybble when setting up the
config field of a perf_event_attr structure for a call to
perf_event_create_kernel_counter().
Fixes: ca724305a2 ("KVM: x86/vPMU: Implement AMD vPMU code for KVM")
Reported-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Jim Mattson <jmattson@google.com>
Message-Id: <20220203014813.2130559-1-jmattson@google.com>
Reviewed-by: David Dunn <daviddunn@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c174f305c ]
The find_arch_event() returns a "unsigned int" value,
which is used by the pmc_reprogram_counter() to
program a PERF_TYPE_HARDWARE type perf_event.
The returned value is actually the kernel defined generic
perf_hw_id, let's rename it to pmc_perf_hw_id() with simpler
incoming parameters for better self-explanation.
Signed-off-by: Like Xu <likexu@tencent.com>
Message-Id: <20211130074221.93635-3-likexu@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 36415a7964 upstream.
The brcmnand driver contains a bug in which if a page (example 2k byte)
is read from the parallel/ONFI NAND and within that page a subpage (512
byte) has correctable errors which is followed by a subpage with
uncorrectable errors, the page read will return the wrong status of
correctable (as opposed to the actual status of uncorrectable.)
The bug is in function brcmnand_read_by_pio where there is a check for
uncorrectable bits which will be preempted if a previous status for
correctable bits is detected.
The fix is to stop checking for bad bits only if we already have a bad
bits status.
Fixes: 27c5b17cd1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Signed-off-by: david regan <dregan@mail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/trinity-478e0c09-9134-40e8-8f8c-31c371225eda-1643237024774@3c-app-mailcom-lxa02
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c23b3f965 upstream.
Interacting with a NAND chip on an IPQ6018 I found that the qcomsmem NAND
partition parser was returning -EPROBE_DEFER waiting for the main smem
driver to load.
This caused the board to reset. Playing about with the probe() function
shows that the problem lies in the core clock being switched off before the
nandc_unalloc() routine has completed.
If we look at how qcom_nandc_remove() tears down allocated resources we see
the expected order is
qcom_nandc_unalloc(nandc);
clk_disable_unprepare(nandc->aon_clk);
clk_disable_unprepare(nandc->core_clk);
dma_unmap_resource(&pdev->dev, nandc->base_dma, resource_size(res),
DMA_BIDIRECTIONAL, 0);
Tweaking probe() to both bring up and tear-down in that order removes the
reset if we end up deferring elsewhere.
Fixes: c76b78d8ec ("mtd: nand: Qualcomm NAND controller driver")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220103030316.58301-2-bryan.odonoghue@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3593030761 upstream.
Daniel Gibson reports that the n_tty code gets line termination wrong in
very specific cases:
"If you feed a line with exactly 64 chars + terminating newline, and
directly afterwards (without reading) another line into a pseudo
terminal, the the first read() on the other side will return the 64
char line *without* terminating newline, and the next read() will
return the missing terminating newline AND the complete next line (if
it fits in the buffer)"
and bisected the behavior to commit 3b830a9c34 ("tty: convert
tty_ldisc_ops 'read()' function to take a kernel pointer").
Now, digging deeper, it turns out that the behavior isn't exactly new:
what changed in commit 3b830a9c34 was that the tty line discipline
.read() function is now passed an intermediate kernel buffer rather than
the final user space buffer.
And that intermediate kernel buffer is 64 bytes in size - thus that
special case with exactly 64 bytes plus terminating newline.
The same problem did exist before, but historically the boundary was not
the 64-byte chunk, but the user-supplied buffer size, which is obviously
generally bigger (and potentially bigger than N_TTY_BUF_SIZE, which
would hide the issue entirely).
The reason is that the n_tty canon_copy_from_read_buf() code would look
ahead for the EOL character one byte further than it would actually
copy. It would then decide that it had found the terminator, and unmark
it as an EOL character - which in turn explains why the next read
wouldn't then be terminated by it.
Now, the reason it did all this in the first place is related to some
historical and pretty obscure EOF behavior, see commit ac8f3bf883
("n_tty: Fix poll() after buffer-limited eof push read") and commit
40d5e0905a ("n_tty: Fix EOF push handling").
And the reason for the EOL confusion is that we treat EOF as a special
EOL condition, with the EOL character being NUL (aka "__DISABLED_CHAR"
in the kernel sources).
So that EOF look-ahead also affects the normal EOL handling.
This patch just removes the look-ahead that causes problems, because EOL
is much more critical than the historical "EOF in the middle of a line
that coincides with the end of the buffer" handling ever was.
Now, it is possible that we should indeed re-introduce the "look at next
character to see if it's a EOF" behavior, but if so, that should be done
not at the kernel buffer chunk boundary in canon_copy_from_read_buf(),
but at a higher level, when we run out of the user buffer.
In particular, the place to do that would be at the top of
'n_tty_read()', where we check if it's a continuation of a previously
started read, and there is no more buffer space left, we could decide to
just eat the __DISABLED_CHAR at that point.
But that would be a separate patch, because I suspect nobody actually
cares, and I'd like to get a report about it before bothering.
Fixes: 3b830a9c34 ("tty: convert tty_ldisc_ops 'read()' function to take a kernel pointer")
Fixes: ac8f3bf883 ("n_tty: Fix poll() after buffer-limited eof push read")
Fixes: 40d5e0905a ("n_tty: Fix EOF push handling")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215611
Reported-and-tested-by: Daniel Gibson <metalcaedes@gmail.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d19e0183a8 upstream.
The result of the writeback, whether it is an ENOSPC or an EIO, or
anything else, does not inhibit the NFS client from reporting the
correct file timestamps.
Fixes: 79566ef018 ("NFS: Getattr doesn't require data sync semantics")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e0caaf75d4 upstream.
Commit ac795161c9 (NFSv4: Handle case where the lookup of a directory
fails) [1], part of Linux since 5.17-rc2, introduced a regression, where
a symbolic link on an NFS mount to a directory on another NFS does not
resolve(?) the first time it is accessed:
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Fixes: ac795161c9 ("NFSv4: Handle case where the lookup of a directory fails")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Tested-by: Donald Buczek <buczek@molgen.mpg.de>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e92bc4cd34 upstream.
Now that we disable wbt by set WBT_STATE_OFF_DEFAULT in
wbt_disable_default() when switch elevator to bfq. And when
we remove scsi device, wbt will be enabled by wbt_enable_default.
If it become false positive between wbt_wait() and wbt_track()
when submit write request.
The following is the scenario that triggered the problem.
T1 T2 T3
elevator_switch_mq
bfq_init_queue
wbt_disable_default <= Set
rwb->enable_state (OFF)
Submit_bio
blk_mq_make_request
rq_qos_throttle
<= rwb->enable_state (OFF)
scsi_remove_device
sd_remove
del_gendisk
blk_unregister_queue
elv_unregister_queue
wbt_enable_default
<= Set rwb->enable_state (ON)
q_qos_track
<= rwb->enable_state (ON)
^^^^^^ this request will mark WBT_TRACKED without inflight add and will
lead to drop rqw->inflight to -1 in wbt_done() which will trigger IO hung.
Fix this by move wbt_enable_default() from elv_unregister to
bfq_exit_queue(). Only re-enable wbt when bfq exit.
Fixes: 76a8040817 ("blk-wbt: make sure throttle is enabled properly")
Remove oneline stale comment, and kill one oneshot local variable.
Signed-off-by: Ming Lei <ming.lei@rehdat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/linux-block/20211214133103.551813-1-qiulaibin@huawei.com/
Signed-off-by: Laibin Qiu <qiulaibin@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe663df782 upstream.
Building tinyconfig with gcc (Debian 11.2.0-16) and assembler (Debian
2.37.90.20220207) the following build error shows up:
{standard input}: Assembler messages:
{standard input}:2088: Error: unrecognized opcode: `ptesync'
make[3]: *** [/builds/linux/scripts/Makefile.build:287: arch/powerpc/lib/sstep.o] Error 1
Add the 'ifdef CONFIG_PPC64' around the 'ptesync' in function
'emulate_update_regs()' to like it is in 'analyse_instr()'. Since it looks like
it got dropped inadvertently by commit 3cdfcbfd32 ("powerpc: Change
analyse_instr so it doesn't modify *regs").
A key detail is that analyse_instr() will never recognise lwsync or
ptesync on 32-bit (because of the existing ifdef), and as a result
emulate_update_regs() should never be called with an op specifying
either of those on 32-bit. So removing them from emulate_update_regs()
should be a nop in terms of runtime behaviour.
Fixes: 3cdfcbfd32 ("powerpc: Change analyse_instr so it doesn't modify *regs")
Cc: stable@vger.kernel.org # v4.14+
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
[mpe: Add last paragraph of change log mentioning analyse_instr() details]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220211005113.1361436-1-anders.roxell@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a845837e3 upstream.
The recently introduced coef_mutex for Realtek codec seems causing a
deadlock when the relevant code is invoked from the power-off state;
then the HD-audio core tries to power-up internally, and this kicks
off the codec runtime PM code that tries to take the same coef_mutex.
In order to avoid the deadlock, do the temporary power up/down around
the coef_mutex acquisition and release. This assures that the
power-up sequence runs before the mutex, hence no re-entrance will
happen.
Fixes: b837a9f5ab ("ALSA: hda: realtek: Fix race at concurrent COEF updates")
Reported-and-tested-by: Julian Wollrath <jwollrath@web.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220214132838.4db10fca@schienar
Link: https://lore.kernel.org/r/20220214130410.21230-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a7e793a867 upstream.
non-regular file needs to be compiled and then copied to the output
directory. Remove it from TEST_PROGS and add it to TEST_GEN_PROGS. This
removes error thrown by rsync when non-regular object isn't found:
rsync: [sender] link_stat "/linux/tools/testing/selftests/exec/non-regular" failed: No such file or directory (2)
rsync error: some files/attrs were not transferred (see previous errors) (code 23) at main.c(1333) [sender=3.2.3]
Fixes: 0f71241a8e ("selftests/exec: add file type errno tests")
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31ded1535e upstream.
This was detected by the gcc in Fedora Rawhide's gcc:
50 11.01 fedora:rawhide : FAIL gcc version 12.0.1 20220205 (Red Hat 12.0.1-0) (GCC)
inlined from 'bpf__config_obj' at util/bpf-loader.c:1242:9:
util/bpf-loader.c:1225:34: error: pointer 'map_opt' may be used after 'free' [-Werror=use-after-free]
1225 | *key_scan_pos += strlen(map_opt);
| ^~~~~~~~~~~~~~~
util/bpf-loader.c:1223:9: note: call to 'free' here
1223 | free(map_name);
| ^~~~~~~~~~~~~~
cc1: all warnings being treated as errors
So do the calculations on the pointer before freeing it.
Fixes: 04f9bf2bac ("perf bpf-loader: Add missing '*' for key_scan_pos")
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang ShaoBo <bobo.shaobowang@huawei.com>
Link: https://lore.kernel.org/lkml/Yg1VtQxKrPpS3uNA@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07dd44852b upstream.
1588 Single Step Timestamping code path uses a mutex to
enforce atomicity for two events:
- update of ptp single step register
- transmit ptp event packet
Before this patch the mutex was not initialized. This
caused unexpected crashes in the Tx function.
Fixes: c55211892f ("dpaa2-eth: support PTP Sync packet one-step timestamping")
Signed-off-by: Radu Bulie <radu-andrei.bulie@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52a9dab6d8 upstream.
GCC 12 correctly reports a potential use-after-free condition in the
xrealloc helper. Fix the warning by avoiding an implicit "free(ptr)"
when size == 0:
In file included from help.c:12:
In function 'xrealloc',
inlined from 'add_cmdname' at help.c:24:2: subcmd-util.h:56:23: error: pointer may be used after 'realloc' [-Werror=use-after-free]
56 | ret = realloc(ptr, size);
| ^~~~~~~~~~~~~~~~~~
subcmd-util.h:52:21: note: call to 'realloc' here
52 | void *ret = realloc(ptr, size);
| ^~~~~~~~~~~~~~~~~~
subcmd-util.h:58:31: error: pointer may be used after 'realloc' [-Werror=use-after-free]
58 | ret = realloc(ptr, 1);
| ^~~~~~~~~~~~~~~
subcmd-util.h:52:21: note: call to 'realloc' here
52 | void *ret = realloc(ptr, size);
| ^~~~~~~~~~~~~~~~~~
Fixes: 2f4ce5ec1d ("perf tools: Finalize subcmd independence")
Reported-by: Valdis Klētnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Kees Kook <keescook@chromium.org>
Tested-by: Valdis Klētnieks <valdis.kletnieks@vt.edu>
Tested-by: Justin M. Forbes <jforbes@fedoraproject.org>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: linux-hardening@vger.kernel.org
Cc: Valdis Klētnieks <valdis.kletnieks@vt.edu>
Link: http://lore.kernel.org/lkml/20220213182443.4037039-1-keescook@chromium.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dcd54265c8 upstream.
trace_napi_poll_hit() is reading stat->dev while another thread can write
on it from dropmon_net_event()
Use READ_ONCE()/WRITE_ONCE() here, RCU rules are properly enforced already,
we only have to take care of load/store tearing.
BUG: KCSAN: data-race in dropmon_net_event / trace_napi_poll_hit
write to 0xffff88816f3ab9c0 of 8 bytes by task 20260 on cpu 1:
dropmon_net_event+0xb8/0x2b0 net/core/drop_monitor.c:1579
notifier_call_chain kernel/notifier.c:84 [inline]
raw_notifier_call_chain+0x53/0xb0 kernel/notifier.c:392
call_netdevice_notifiers_info net/core/dev.c:1919 [inline]
call_netdevice_notifiers_extack net/core/dev.c:1931 [inline]
call_netdevice_notifiers net/core/dev.c:1945 [inline]
unregister_netdevice_many+0x867/0xfb0 net/core/dev.c:10415
ip_tunnel_delete_nets+0x24a/0x280 net/ipv4/ip_tunnel.c:1123
vti_exit_batch_net+0x2a/0x30 net/ipv4/ip_vti.c:515
ops_exit_list net/core/net_namespace.c:173 [inline]
cleanup_net+0x4dc/0x8d0 net/core/net_namespace.c:597
process_one_work+0x3f6/0x960 kernel/workqueue.c:2307
worker_thread+0x616/0xa70 kernel/workqueue.c:2454
kthread+0x1bf/0x1e0 kernel/kthread.c:377
ret_from_fork+0x1f/0x30
read to 0xffff88816f3ab9c0 of 8 bytes by interrupt on cpu 0:
trace_napi_poll_hit+0x89/0x1c0 net/core/drop_monitor.c:292
trace_napi_poll include/trace/events/napi.h:14 [inline]
__napi_poll+0x36b/0x3f0 net/core/dev.c:6366
napi_poll net/core/dev.c:6432 [inline]
net_rx_action+0x29e/0x650 net/core/dev.c:6519
__do_softirq+0x158/0x2de kernel/softirq.c:558
do_softirq+0xb1/0xf0 kernel/softirq.c:459
__local_bh_enable_ip+0x68/0x70 kernel/softirq.c:383
__raw_spin_unlock_bh include/linux/spinlock_api_smp.h:167 [inline]
_raw_spin_unlock_bh+0x33/0x40 kernel/locking/spinlock.c:210
spin_unlock_bh include/linux/spinlock.h:394 [inline]
ptr_ring_consume_bh include/linux/ptr_ring.h:367 [inline]
wg_packet_decrypt_worker+0x73c/0x780 drivers/net/wireguard/receive.c:506
process_one_work+0x3f6/0x960 kernel/workqueue.c:2307
worker_thread+0x616/0xa70 kernel/workqueue.c:2454
kthread+0x1bf/0x1e0 kernel/kthread.c:377
ret_from_fork+0x1f/0x30
value changed: 0xffff88815883e000 -> 0x0000000000000000
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 26435 Comm: kworker/0:1 Not tainted 5.17.0-rc1-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: wg-crypt-wg2 wg_packet_decrypt_worker
Fixes: 4ea7e38696 ("dropmon: add ability to detect when hardware dropsrxpackets")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6ab75cec1 upstream.
In __bond_release_one(), bond_set_carrier() is only called when bond
device has no slave. Therefore, if we remove the up slave from a master
with two slaves and keep the down slave, the master will remain up.
Fix this by moving bond_set_carrier() out of if (!bond_has_slaves(bond))
statement.
Reproducer:
$ insmod bonding.ko mode=0 miimon=100 max_bonds=2
$ ifconfig bond0 up
$ ifenslave bond0 eth0 eth1
$ ifconfig eth0 down
$ ifenslave -d bond0 eth1
$ cat /proc/net/bonding/bond0
Fixes: ff59c4563a ("[PATCH] bonding: support carrier state for master")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/1645021088-38370-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 35a79e64de upstream.
When 'ping' changes to use PING socket instead of RAW socket by:
# sysctl -w net.ipv4.ping_group_range="0 100"
There is another regression caused when matching sk_bound_dev_if
and dif, RAW socket is using inet_iif() while PING socket lookup
is using skb->dev->ifindex, the cmd below fails due to this:
# ip link add dummy0 type dummy
# ip link set dummy0 up
# ip addr add 192.168.111.1/24 dev dummy0
# ping -I dummy0 192.168.111.1 -c1
The issue was also reported on:
https://github.com/iputils/iputils/issues/104
But fixed in iputils in a wrong way by not binding to device when
destination IP is on device, and it will cause some of kselftests
to fail, as Jianlin noticed.
This patch is to use inet(6)_iif and inet(6)_sdif to get dif and
sdif for PING socket, and keep consistent with RAW socket.
Fixes: c319b4d76b ("net: ipv4: add IPPROTO_ICMP socket kind")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6bb9681a43 upstream.
The reset input to the LAN9303 chip is active low, and devicetree
gpio handles reflect this. Therefore, the gpio should be requested
with an initial state of high in order for the reset signal to be
asserted. Other uses of the gpio already use the correct polarity.
Fixes: a1292595e0 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fianelil <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220209145454.19749-1-mans@mansr.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b0dff5b3b upstream.
Ipv6 flowlabels historically require a reservation before use.
Optionally in exclusive mode (e.g., user-private).
Commit 59c820b231 ("ipv6: elide flowlabel check if no exclusive
leases exist") introduced a fastpath that avoids this check when no
exclusive leases exist in the system, and thus any flowlabel use
will be granted.
That allows skipping the control operation to reserve a flowlabel
entirely. Though with a warning if the fast path fails:
This is an optimization. Robust applications still have to revert to
requesting leases if the fast path fails due to an exclusive lease.
Still, this is subtle. Better isolate network namespaces from each
other. Flowlabels are per-netns. Also record per-netns whether
exclusive leases are in use. Then behavior does not change based on
activity in other netns.
Changes
v2
- wrap in IS_ENABLED(CONFIG_IPV6) to avoid breakage if disabled
Fixes: 59c820b231 ("ipv6: elide flowlabel check if no exclusive leases exist")
Link: https://lore.kernel.org/netdev/MWHPR2201MB1072BCCCFCE779E4094837ACD0329@MWHPR2201MB1072.namprd22.prod.outlook.com/
Reported-by: Congyu Liu <liu3101@purdue.edu>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Tested-by: Congyu Liu <liu3101@purdue.edu>
Link: https://lore.kernel.org/r/20220215160037.1976072-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e71ec1a72 upstream.
When the nft_concat_range test failed, it exit 1 in the code
specifically.
But when part of, or all of the test passed, it will failed the
[ ${passed} -eq 0 ] check and thus exit with 1, which is the same
exit value with failure result. Fix it by exit 0 when passed is not 0.
Fixes: 611973c1e0 ("selftests: netfilter: Introduce tests for sets with range concatenation")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b9208492fc upstream.
vsock_connect() expects that the socket could already be in the
TCP_ESTABLISHED state when the connecting task wakes up with a signal
pending. If this happens the socket will be in the connected table, and
it is not removed when the socket state is reset. In this situation it's
common for the process to retry connect(), and if the connection is
successful the socket will be added to the connected table a second
time, corrupting the list.
Prevent this by calling vsock_remove_connected() if a signal is received
while waiting for a connection. This is harmless if the socket is not in
the connected table, and if it is in the table then removing it will
prevent list corruption from a double add.
Note for backporting: this patch requires d5afa82c97 ("vsock: correct
removal of socket from the list"), which is in all current stable trees
except 4.9.y.
Fixes: d021c34405 ("VSOCK: Introduce VM Sockets")
Signed-off-by: Seth Forshee <sforshee@digitalocean.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/20220217141312.2297547-1-sforshee@digitalocean.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6a3193cdd5 upstream.
Merge module sections only when using Clang LTO. With ld.bfd, merging
sections does not appear to update the symbol tables for the module,
e.g. 'readelf -s' shows the value that a symbol would have had, if
sections were not merged. ld.lld does not show this problem.
The stale symbol table breaks gdb's function disassembler, and presumably
other things, e.g.
gdb -batch -ex "file arch/x86/kvm/kvm.ko" -ex "disassemble kvm_init"
reads the wrong bytes and dumps garbage.
Fixes: dd2776222a ("kbuild: lto: merge module sections")
Cc: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Tested-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210322234438.502582-1-seanjc@google.com
Cc: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 042e293e16 ]
When account() is called, and the amount of entropy dips below
random_write_wakeup_bits, we wake up the random writers, so that they
can write some more in. However, the RNDZAPENTCNT/RNDCLEARPOOL ioctl
sets the entropy count to zero -- a potential reduction just like
account() -- but does not unblock writers. This commit adds the missing
logic to that ioctl to unblock waiting writers.
Reviewed-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dcb85f85fa ]
While the stackleak plugin was already using notrace, objtool is now a
bit more picky. Update the notrace uses to noinstr. Silences the
following objtool warnings when building with:
CONFIG_DEBUG_ENTRY=y
CONFIG_STACK_VALIDATION=y
CONFIG_VMLINUX_VALIDATION=y
CONFIG_GCC_PLUGIN_STACKLEAK=y
vmlinux.o: warning: objtool: do_syscall_64()+0x9: call to stackleak_track_stack() leaves .noinstr.text section
vmlinux.o: warning: objtool: do_int80_syscall_32()+0x9: call to stackleak_track_stack() leaves .noinstr.text section
vmlinux.o: warning: objtool: exc_general_protection()+0x22: call to stackleak_track_stack() leaves .noinstr.text section
vmlinux.o: warning: objtool: fixup_bad_iret()+0x20: call to stackleak_track_stack() leaves .noinstr.text section
vmlinux.o: warning: objtool: do_machine_check()+0x27: call to stackleak_track_stack() leaves .noinstr.text section
vmlinux.o: warning: objtool: .text+0x5346e: call to stackleak_erase() leaves .noinstr.text section
vmlinux.o: warning: objtool: .entry.text+0x143: call to stackleak_erase() leaves .noinstr.text section
vmlinux.o: warning: objtool: .entry.text+0x10eb: call to stackleak_erase() leaves .noinstr.text section
vmlinux.o: warning: objtool: .entry.text+0x17f9: call to stackleak_erase() leaves .noinstr.text section
Note that the plugin's addition of calls to stackleak_track_stack() from
noinstr functions is expected to be safe, as it isn't runtime
instrumentation and is self-contained.
Cc: Alexander Popov <alex.popov@linux.com>
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 67d6212afd ]
This reverts commit 774a1221e8.
We need to finish all async code before the module init sequence is
done. In the reverted commit the PF_USED_ASYNC flag was added to mark a
thread that called async_schedule(). Then the PF_USED_ASYNC flag was
used to determine whether or not async_synchronize_full() needs to be
invoked. This works when modprobe thread is calling async_schedule(),
but it does not work if module dispatches init code to a worker thread
which then calls async_schedule().
For example, PCI driver probing is invoked from a worker thread based on
a node where device is attached:
if (cpu < nr_cpu_ids)
error = work_on_cpu(cpu, local_pci_probe, &ddi);
else
error = local_pci_probe(&ddi);
We end up in a situation where a worker thread gets the PF_USED_ASYNC
flag set instead of the modprobe thread. As a result,
async_synchronize_full() is not invoked and modprobe completes without
waiting for the async code to finish.
The issue was discovered while loading the pm80xx driver:
(scsi_mod.scan=async)
modprobe pm80xx worker
...
do_init_module()
...
pci_call_probe()
work_on_cpu(local_pci_probe)
local_pci_probe()
pm8001_pci_probe()
scsi_scan_host()
async_schedule()
worker->flags |= PF_USED_ASYNC;
...
< return from worker >
...
if (current->flags & PF_USED_ASYNC) <--- false
async_synchronize_full();
Commit 21c3c5d280 ("block: don't request module during elevator init")
fixed the deadlock issue which the reverted commit 774a1221e8
("module, async: async_synchronize_full() on module init iff async is
used") tried to fix.
Since commit 0fdff3ec6d ("async, kmod: warn on synchronous
request_module() from async workers") synchronous module loading from
async is not allowed.
Given that the original deadlock issue is fixed and it is no longer
allowed to call synchronous request_module() from async we can remove
PF_USED_ASYNC flag to make module init consistently invoke
async_synchronize_full() unless async module probe is requested.
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Reviewed-by: Changyuan Lyu <changyuanl@google.com>
Reviewed-by: Luis Chamberlain <mcgrof@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e25a8d9599 ]
This started out with me noticing that "dom0_max_vcpus=<N>" with <N>
larger than the number of physical CPUs reported through ACPI tables
would not bring up the "excess" vCPU-s. Addressing this is the primary
purpose of the change; CPU maps handling is being tidied only as far as
is necessary for the change here (with the effect of also avoiding the
setting up of too much per-CPU infrastructure, i.e. for CPUs which can
never come online).
Noticing that xen_fill_possible_map() is called way too early, whereas
xen_filter_cpu_maps() is called too late (after per-CPU areas were
already set up), and further observing that each of the functions serves
only one of Dom0 or DomU, it looked like it was better to simplify this.
Use the .get_smp_config hook instead, uniformly for Dom0 and DomU.
xen_fill_possible_map() can be dropped altogether, while
xen_filter_cpu_maps() is re-purposed but not otherwise changed.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/2dbd5f0a-9859-ca2d-085e-a02f7166c610@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6bb1722f3 ]
While nvme_rdma_submit_async_event_work is checking the ctrl and queue
state before preparing the AER command and scheduling io_work, in order
to fully prevent a race where this check is not reliable the error
recovery work must flush async_event_work before continuing to destroy
the admin queue after setting the ctrl state to RESETTING such that
there is no race .submit_async_event and the error recovery handler
itself changing the ctrl state.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff9fc7ebf5 ]
While nvme_tcp_submit_async_event_work is checking the ctrl and queue
state before preparing the AER command and scheduling io_work, in order
to fully prevent a race where this check is not reliable the error
recovery work must flush async_event_work before continuing to destroy
the admin queue after setting the ctrl state to RESETTING such that
there is no race .submit_async_event and the error recovery handler
itself changing the ctrl state.
Tested-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0fa0f99fc8 ]
Unlike .queue_rq, in .submit_async_event drivers may not check the ctrl
readiness for AER submission. This may lead to a use-after-free
condition that was observed with nvme-tcp.
The race condition may happen in the following scenario:
1. driver executes its reset_ctrl_work
2. -> nvme_stop_ctrl - flushes ctrl async_event_work
3. ctrl sends AEN which is received by the host, which in turn
schedules AEN handling
4. teardown admin queue (which releases the queue socket)
5. AEN processed, submits another AER, calling the driver to submit
6. driver attempts to send the cmd
==> use-after-free
In order to fix that, add ctrl state check to validate the ctrl
is actually able to accept the AER submission.
This addresses the above race in controller resets because the driver
during teardown should:
1. change ctrl state to RESETTING
2. flush async_event_work (as well as other async work elements)
So after 1,2, any other AER command will find the
ctrl state to be RESETTING and bail out without submitting the AER.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df7abcaa12 ]
Currently a use-after-free may occur if a sas_task is aborted by the upper
layer before we handle the I/O completion in mpi_ssp_completion() or
mpi_sata_completion().
In this case, the following are the two steps in handling those I/O
completions:
- Call complete() to inform the upper layer handler of completion of
the I/O.
- Release driver resources associated with the sas_task in
pm8001_ccb_task_free() call.
When complete() is called, the upper layer may free the sas_task. As such,
we should not touch the associated sas_task afterwards, but we do so in the
pm8001_ccb_task_free() call.
Fix by swapping the complete() and pm8001_ccb_task_free() calls ordering.
Link: https://lore.kernel.org/r/1643289172-165636-4-git-send-email-john.garry@huawei.com
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61f162aa43 ]
Currently a use-after-free may occur if a TMF sas_task is aborted before we
handle the IO completion in mpi_ssp_completion(). The abort occurs due to
timeout.
When the timeout occurs, the SAS_TASK_STATE_ABORTED flag is set and the
sas_task is freed in pm8001_exec_internal_tmf_task().
However, if the I/O completion occurs later, the I/O completion still
thinks that the sas_task is available. Fix this by clearing the ccb->task
if the TMF times out - the I/O completion handler does nothing if this
pointer is cleared.
Link: https://lore.kernel.org/r/1643289172-165636-3-git-send-email-john.garry@huawei.com
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd5532a499 ]
Strangely, dquot_quota_sync ignores the return code from the ->sync_fs
call, which means that quotacalls like Q_SYNC never see the error. This
doesn't seem right, so fix that.
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2719c7160d ]
If we fail to synchronize the filesystem while preparing to freeze the
fs, abort the freeze.
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e0f718daf ]
The previous commit 1ade48d0c2 ("ax25: NPD bug when detaching
AX25 device") introduce lock_sock() into ax25_kill_by_device to
prevent NPD bug. But the concurrency NPD or UAF bug will occur,
when lock_sock() or release_sock() dereferences the ax25_cb->sock.
The NULL pointer dereference bug can be shown as below:
ax25_kill_by_device() | ax25_release()
| ax25_destroy_socket()
| ax25_cb_del()
... | ...
| ax25->sk=NULL;
lock_sock(s->sk); //(1) |
s->ax25_dev = NULL; | ...
release_sock(s->sk); //(2) |
... |
The root cause is that the sock is set to null before dereference
site (1) or (2). Therefore, this patch extracts the ax25_cb->sock
in advance, and uses ax25_list_lock to protect it, which can synchronize
with ax25_cb_del() and ensure the value of sock is not null before
dereference sites.
The concurrency UAF bug can be shown as below:
ax25_kill_by_device() | ax25_release()
| ax25_destroy_socket()
... | ...
| sock_put(sk); //FREE
lock_sock(s->sk); //(1) |
s->ax25_dev = NULL; | ...
release_sock(s->sk); //(2) |
... |
The root cause is that the sock is released before dereference
site (1) or (2). Therefore, this patch uses sock_hold() to increase
the refcount of sock and uses ax25_list_lock to protect it, which
can synchronize with ax25_cb_del() in ax25_destroy_socket() and
ensure the sock wil not be released before dereference sites.
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dae1d8ac31 ]
Report mincore.check_file_mmap as SKIP instead of FAIL if the underlying
filesystem lacks support of O_TMPFILE or fallocate since such failures
are not really related to mincore functionality.
Cc: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 01dabed205 ]
If zram-generator package is installed and works, then we can not remove
zram module because zram swap is being used. This case needs a clean zram
environment, change this test by using hot_add/hot_remove interface. So
even zram device is being used, we still can add zram device and remove
them in cleanup.
The two interface was introduced since kernel commit 6566d1a32bf7("zram:
add dynamic device add/remove functionality") in v4.2-rc1. If kernel
supports these two interface, we use hot_add/hot_remove to slove this
problem, if not, just check whether zram is being used or built in, then
skip it on old kernel.
Signed-off-by: Yang Xu <xuyang2018.jy@fujitsu.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d18da7ec37 ]
zram01 uses `free -m` to measure zram memory usage. The results are no
sense because they are polluted by all running processes on the system.
We Should only calculate the free memory delta for the current process.
So use the third field of /sys/block/zram<id>/mm_stat to measure memory
usage instead. The file is available since kernel 4.1.
orig_data_size(first): uncompressed size of data stored in this disk.
compr_data_size(second): compressed size of data stored in this disk
mem_used_total(third): the amount of memory allocated for this disk
Also remove useless zram cleanup call in zram_fill_fs and so we don't
need to cleanup zram twice if fails.
Signed-off-by: Yang Xu <xuyang2018.jy@fujitsu.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc4eb486a5 ]
Since commit 43209ea2d1 ("zram: remove max_comp_streams internals"), zram
has switched to per-cpu streams. Even kernel still keep this interface for
some reasons, but writing to max_comp_stream doesn't take any effect. So
skip it on newer kernel ie 4.7.
The code that comparing kernel version is from xfstests testsuite ext4/053.
Signed-off-by: Yang Xu <xuyang2018.jy@fujitsu.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5ce576d45 ]
Upon error the ieee802154_xmit_complete() helper is not called. Only
ieee802154_wake_queue() is called manually. In the Tx case we then leak
the skb structure.
Free the skb structure upon error before returning when appropriate.
As the 'is_tx = 0' cannot be moved in the complete handler because of a
possible race between the delay in switching to STATE_RX_AACK_ON and a
new interrupt, we introduce an intermediate 'was_tx' boolean just for
this purpose.
There is no Fixes tag applying here, many changes have been made on this
area and the issue kind of always existed.
Suggested-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20220125121426.848337-4-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92d25637a3 ]
We have some many cases that will create child process as well, such as
pidfd_wait. Previously, we will signal/kill the parent process when it
is time out, but this signal will not be sent to its child process. In
such case, if child process doesn't terminate itself, ksefltest framework
will hang forever.
Here we group all its child processes so that kill() can signal all of
them in timeout.
Fixed change log: Shuah Khan <skhan@linuxfoundation.org>
Suggested-by: yang xu <xuyang2018.jy@cn.fujitsu.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f034cc1301 ]
The timeout setting for the rtc kselftest is currently 90 seconds. This
setting is used by the kselftest runner to stop running a test if it
takes longer than the assigned value.
However, two of the test cases inside rtc set alarms. These alarms are
set to the next beginning of the minute, so each of these test cases may
take up to, in the worst case, 60 seconds.
In order to allow for all test cases in rtc to run, even in the worst
case, when using the kselftest runner, the timeout value should be
increased to at least 120. Set it to 180, so there's some additional
slack.
Correct operation can be tested by running the following command right
after the start of a minute (low second count), and checking that all
test cases run:
./run_kselftest.sh -c rtc
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 17da2d5f93 ]
As reported:
[ 256.104522] ======================================================
[ 256.113783] WARNING: possible circular locking dependency detected
[ 256.120093] 5.16.0-rc6-yocto-standard+ #99 Not tainted
[ 256.125362] ------------------------------------------------------
[ 256.131673] intel-speed-sel/844 is trying to acquire lock:
[ 256.137290] ffffffffc036f0d0 (punit_misc_dev_lock){+.+.}-{3:3}, at: isst_if_open+0x18/0x90 [isst_if_common]
[ 256.147171]
[ 256.147171] but task is already holding lock:
[ 256.153135] ffffffff8ee7cb50 (misc_mtx){+.+.}-{3:3}, at: misc_open+0x2a/0x170
[ 256.160407]
[ 256.160407] which lock already depends on the new lock.
[ 256.160407]
[ 256.168712]
[ 256.168712] the existing dependency chain (in reverse order) is:
[ 256.176327]
[ 256.176327] -> #1 (misc_mtx){+.+.}-{3:3}:
[ 256.181946] lock_acquire+0x1e6/0x330
[ 256.186265] __mutex_lock+0x9b/0x9b0
[ 256.190497] mutex_lock_nested+0x1b/0x20
[ 256.195075] misc_register+0x32/0x1a0
[ 256.199390] isst_if_cdev_register+0x65/0x180 [isst_if_common]
[ 256.205878] isst_if_probe+0x144/0x16e [isst_if_mmio]
...
[ 256.241976]
[ 256.241976] -> #0 (punit_misc_dev_lock){+.+.}-{3:3}:
[ 256.248552] validate_chain+0xbc6/0x1750
[ 256.253131] __lock_acquire+0x88c/0xc10
[ 256.257618] lock_acquire+0x1e6/0x330
[ 256.261933] __mutex_lock+0x9b/0x9b0
[ 256.266165] mutex_lock_nested+0x1b/0x20
[ 256.270739] isst_if_open+0x18/0x90 [isst_if_common]
[ 256.276356] misc_open+0x100/0x170
[ 256.280409] chrdev_open+0xa5/0x1e0
...
The call sequence suggested that misc_device /dev file can be opened
before misc device is yet to be registered, which is done only once.
Here punit_misc_dev_lock was used as common lock, to protect the
registration by multiple ISST HW drivers, one time setup, prevent
duplicate registry of misc device and prevent load/unload when device
is open.
We can split into locks:
- One which just prevent duplicate call to misc_register() and one
time setup. Also never call again if the misc_register() failed or
required one time setup is failed. This lock is not shared with
any misc device callbacks.
- The other lock protects registry, load and unload of HW drivers.
Sequence in isst_if_cdev_register()
- Register callbacks under punit_misc_dev_open_lock
- Call isst_misc_reg() which registers misc_device on the first
registry which is under punit_misc_dev_reg_lock, which is not
shared with callbacks.
Sequence in isst_if_cdev_unregister
Just opposite of isst_if_cdev_register
Reported-and-tested-by: Liwei Song <liwei.song@windriver.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20220112022521.54669-1-srinivas.pandruvada@linux.intel.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 18a1d5e194 upstream.
It's a followup to the previous commit f15309d7ad ("parisc: Add
ioread64_hi_lo() and iowrite64_hi_lo()") which does only half of
the job. Add the rest, so we won't get a new kernel test robot
reports.
Fixes: f15309d7ad ("parisc: Add ioread64_hi_lo() and iowrite64_hi_lo()")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 80d47f5de5 upstream.
Oded Gabbay reports that enabling NUMA balancing causes corruption with
his Gaudi accelerator test load:
"All the details are in the bug, but the bottom line is that somehow,
this patch causes corruption when the numa balancing feature is
enabled AND we don't use process affinity AND we use GUP to pin pages
so our accelerator can DMA to/from system memory.
Either disabling numa balancing, using process affinity to bind to
specific numa-node or reverting this patch causes the bug to
disappear"
and Oded bisected the issue to commit 09854ba94c ("mm: do_wp_page()
simplification").
Now, the NUMA balancing shouldn't actually be changing the writability
of a page, and as such shouldn't matter for COW. But it appears it
does. Suspicious.
However, regardless of that, the condition for enabling NUMA faults in
change_pte_range() is nonsensical. It uses "page_mapcount(page)" to
decide if a COW page should be NUMA-protected or not, and that makes
absolutely no sense.
The number of mappings a page has is irrelevant: not only does GUP get a
reference to a page as in Oded's case, but the other mappings migth be
paged out and the only reference to them would be in the page count.
Since we should never try to NUMA-balance a page that we can't move
anyway due to other references, just fix the code to use 'page_count()'.
Oded confirms that that fixes his issue.
Now, this does imply that something in NUMA balancing ends up changing
page protections (other than the obvious one of making the page
inaccessible to get the NUMA faulting information). Otherwise the COW
simplification wouldn't matter - since doing the GUP on the page would
make sure it's writable.
The cause of that permission change would be good to figure out too,
since it clearly results in spurious COW events - but fixing the
nonsensical test that just happened to work before is obviously the
CorrectThing(tm) to do regardless.
Fixes: 09854ba94c ("mm: do_wp_page() simplification")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215616
Link: https://lore.kernel.org/all/CAFCwf10eNmwq2wD71xjUhqkvv5+_pJMR1nPug2RqNDcFT4H86Q@mail.gmail.com/
Reported-and-tested-by: Oded Gabbay <oded.gabbay@gmail.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Peter Xu <peterx@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54309fde1a upstream.
On reads with MMC_READ_MULTIPLE_BLOCK that fail,
the recovery handler will use MMC_READ_SINGLE_BLOCK for
each of the blocks, up to MMC_READ_SINGLE_RETRIES times each.
The logic for this is fixed to never report unsuccessful reads
as success to the block layer.
On command error with retries remaining, blk_update_request was
called with whatever value error was set last to.
In case it was last set to BLK_STS_OK (default), the read will be
reported as success, even though there was no data read from the device.
This could happen on a CRC mismatch for the response,
a card rejecting the command (e.g. again due to a CRC mismatch).
In case it was last set to BLK_STS_IOERR, the error is reported correctly,
but no retries will be attempted.
Fixes: 81196976ed ("mmc: block: Add blk-mq support")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/bc706a6ab08c4fe2834ba0c05a804672@hyperstone.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9129886b88 upstream.
With huge kernel pages, we randomly eat a SPARC in map_pages(). This
is fixed by dropping __init from the declaration.
However, map_pages references the __init routine memblock_alloc_try_nid
via memblock_alloc. Thus, it needs to be marked with __ref.
memblock_alloc is only called before the kernel text is set to readonly.
The __ref on free_initmem is no longer needed.
Comment regarding map_pages being in the init section is removed.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd4589eee9 upstream.
Remove a WARN on an "AVIC IPI invalid target" exit, the WARN is trivial
to trigger from guest as it will fail on any destination APIC ID that
doesn't exist from the guest's perspective.
Don't bother recording anything in the kernel log, the common tracepoint
for kvm_avic_incomplete_ipi() is sufficient for debugging.
This reverts commit 37ef0c4414.
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220204214205.3306634-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit efe1dc571a upstream.
Contention for the mailbox interface may occur during driver initialization
(immediately after a function reset), between mailbox commands initiated
via ioctl (bsg) and those driver requested by the driver.
After setting SLI_ACTIVE flag for a port, there is a window in which the
driver will allow an ioctl to be initiated while the adapter is
initializing and issuing mailbox commands via polling. The polling logic
then gets confused.
Correct by having thread setting SLI_ACTIVE spot an active mailbox command
and allow it complete before proceeding.
Link: https://lore.kernel.org/r/20210921143008.64212-1-jsmart2021@gmail.com
Co-developed-by: Nigel Kirkland <nkirkland2304@gmail.com>
Signed-off-by: Nigel Kirkland <nkirkland2304@gmail.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 921ca574cd upstream.
When CAN_ISOTP_SF_BROADCAST is set in the CAN_ISOTP_OPTS flags the CAN_ISOTP
socket is switched into functional addressing mode, where only single frame
(SF) protocol data units can be send on the specified CAN interface and the
given tp.tx_id after bind().
In opposite to normal and extended addressing this socket does not register a
CAN-ID for reception which would be needed for a 1-to-1 ISOTP connection with a
segmented bi-directional data transfer.
Sending SFs on this socket is therefore a TX-only 'broadcast' operation.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Thomas Wagner <thwa1@web.de>
Link: https://lore.kernel.org/r/20201206144731.4609-1-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 24d7275ce2 upstream.
The syzbot reported the below BUG:
kernel BUG at include/linux/page-flags.h:785!
invalid opcode: 0000 [#1] PREEMPT SMP KASAN
CPU: 1 PID: 4392 Comm: syz-executor560 Not tainted 5.16.0-rc6-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:PageDoubleMap include/linux/page-flags.h:785 [inline]
RIP: 0010:__page_mapcount+0x2d2/0x350 mm/util.c:744
Call Trace:
page_mapcount include/linux/mm.h:837 [inline]
smaps_account+0x470/0xb10 fs/proc/task_mmu.c:466
smaps_pte_entry fs/proc/task_mmu.c:538 [inline]
smaps_pte_range+0x611/0x1250 fs/proc/task_mmu.c:601
walk_pmd_range mm/pagewalk.c:128 [inline]
walk_pud_range mm/pagewalk.c:205 [inline]
walk_p4d_range mm/pagewalk.c:240 [inline]
walk_pgd_range mm/pagewalk.c:277 [inline]
__walk_page_range+0xe23/0x1ea0 mm/pagewalk.c:379
walk_page_vma+0x277/0x350 mm/pagewalk.c:530
smap_gather_stats.part.0+0x148/0x260 fs/proc/task_mmu.c:768
smap_gather_stats fs/proc/task_mmu.c:741 [inline]
show_smap+0xc6/0x440 fs/proc/task_mmu.c:822
seq_read_iter+0xbb0/0x1240 fs/seq_file.c:272
seq_read+0x3e0/0x5b0 fs/seq_file.c:162
vfs_read+0x1b5/0x600 fs/read_write.c:479
ksys_read+0x12d/0x250 fs/read_write.c:619
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
The reproducer was trying to read /proc/$PID/smaps when calling
MADV_FREE at the mean time. MADV_FREE may split THPs if it is called
for partial THP. It may trigger the below race:
CPU A CPU B
----- -----
smaps walk: MADV_FREE:
page_mapcount()
PageCompound()
split_huge_page()
page = compound_head(page)
PageDoubleMap(page)
When calling PageDoubleMap() this page is not a tail page of THP anymore
so the BUG is triggered.
This could be fixed by elevated refcount of the page before calling
mapcount, but that would prevent it from counting migration entries, and
it seems overkilling because the race just could happen when PMD is
split so all PTE entries of tail pages are actually migration entries,
and smaps_account() does treat migration entries as mapcount == 1 as
Kirill pointed out.
Add a new parameter for smaps_account() to tell this entry is migration
entry then skip calling page_mapcount(). Don't skip getting mapcount
for device private entries since they do track references with mapcount.
Pagemap also has the similar issue although it was not reported. Fixed
it as well.
[shy828301@gmail.com: v4]
Link: https://lkml.kernel.org/r/20220203182641.824731-1-shy828301@gmail.com
[nathan@kernel.org: avoid unused variable warning in pagemap_pmd_range()]
Link: https://lkml.kernel.org/r/20220207171049.1102239-1-nathan@kernel.org
Link: https://lkml.kernel.org/r/20220120202805.3369-1-shy828301@gmail.com
Fixes: e9b61f1985 ("thp: reintroduce split_huge_page()")
Signed-off-by: Yang Shi <shy828301@gmail.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reported-by: syzbot+1f52b3a18d5633fa7f82@syzkaller.appspotmail.com
Acked-by: David Hildenbrand <david@redhat.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Jann Horn <jannh@google.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e386dfc56f upstream.
Commit 054aa8d439 ("fget: check that the fd still exists after getting
a ref to it") fixed a race with getting a reference to a file just as it
was being closed. It was a fairly minimal patch, and I didn't think
re-checking the file pointer lookup would be a measurable overhead,
since it was all right there and cached.
But I was wrong, as pointed out by the kernel test robot.
The 'poll2' case of the will-it-scale.per_thread_ops benchmark regressed
quite noticeably. Admittedly it seems to be a very artificial test:
doing "poll()" system calls on regular files in a very tight loop in
multiple threads.
That means that basically all the time is spent just looking up file
descriptors without ever doing anything useful with them (not that doing
'poll()' on a regular file is useful to begin with). And as a result it
shows the extra "re-check fd" cost as a sore thumb.
Happily, the regression is fixable by just writing the code to loook up
the fd to be better and clearer. There's still a cost to verify the
file pointer, but now it's basically in the noise even for that
benchmark that does nothing else - and the code is more understandable
and has better comments too.
[ Side note: this patch is also a classic case of one that looks very
messy with the default greedy Myers diff - it's much more legible with
either the patience of histogram diff algorithm ]
Link: https://lore.kernel.org/lkml/20211210053743.GA36420@xsang-OptiPlex-9020/
Link: https://lore.kernel.org/lkml/20211213083154.GA20853@linux.intel.com/
Reported-by: kernel test robot <oliver.sang@intel.com>
Tested-by: Carel Si <beibei.si@intel.com>
Cc: Jann Horn <jannh@google.com>
Cc: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bfb3aa735f upstream.
An outgoing CPU is marked offline in a stop-machine handler and most
of that CPU's services stop at that point, including IRQ work queues.
However, that CPU must take another pass through the scheduler and through
a number of CPU-hotplug notifiers, many of which contain RCU readers.
In the past, these readers were not a problem because the outgoing CPU
has interrupts disabled, so that rcu_read_unlock_special() would not
be invoked, and thus RCU would never attempt to queue IRQ work on the
outgoing CPU.
This changed with the advent of the CONFIG_RCU_STRICT_GRACE_PERIOD
Kconfig option, in which rcu_read_unlock_special() is invoked upon exit
from almost all RCU read-side critical sections. Worse yet, because
interrupts are disabled, rcu_read_unlock_special() cannot immediately
report a quiescent state and will therefore attempt to defer this
reporting, for example, by queueing IRQ work. Which fails with a splat
because the CPU is already marked as being offline.
But it turns out that there is no need to report this quiescent state
because rcu_report_dead() will do this job shortly after the outgoing
CPU makes its final dive into the idle loop. This commit therefore
makes rcu_read_unlock_special() refrain from queuing IRQ work onto
outgoing CPUs.
Fixes: 44bad5b3cc ("rcu: Do full report for .need_qs for strict GPs")
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Cc: Jann Horn <jannh@google.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0764db9b49 upstream.
Alexander reported a circular lock dependency revealed by the mmap1 ltp
test:
LOCKDEP_CIRCULAR (suite: ltp, case: mtest06 (mmap1))
WARNING: possible circular locking dependency detected
5.17.0-20220113.rc0.git0.f2211f194038.300.fc35.s390x+debug #1 Not tainted
------------------------------------------------------
mmap1/202299 is trying to acquire lock:
00000001892c0188 (css_set_lock){..-.}-{2:2}, at: obj_cgroup_release+0x4a/0xe0
but task is already holding lock:
00000000ca3b3818 (&sighand->siglock){-.-.}-{2:2}, at: force_sig_info_to_task+0x38/0x180
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&sighand->siglock){-.-.}-{2:2}:
__lock_acquire+0x604/0xbd8
lock_acquire.part.0+0xe2/0x238
lock_acquire+0xb0/0x200
_raw_spin_lock_irqsave+0x6a/0xd8
__lock_task_sighand+0x90/0x190
cgroup_freeze_task+0x2e/0x90
cgroup_migrate_execute+0x11c/0x608
cgroup_update_dfl_csses+0x246/0x270
cgroup_subtree_control_write+0x238/0x518
kernfs_fop_write_iter+0x13e/0x1e0
new_sync_write+0x100/0x190
vfs_write+0x22c/0x2d8
ksys_write+0x6c/0xf8
__do_syscall+0x1da/0x208
system_call+0x82/0xb0
-> #0 (css_set_lock){..-.}-{2:2}:
check_prev_add+0xe0/0xed8
validate_chain+0x736/0xb20
__lock_acquire+0x604/0xbd8
lock_acquire.part.0+0xe2/0x238
lock_acquire+0xb0/0x200
_raw_spin_lock_irqsave+0x6a/0xd8
obj_cgroup_release+0x4a/0xe0
percpu_ref_put_many.constprop.0+0x150/0x168
drain_obj_stock+0x94/0xe8
refill_obj_stock+0x94/0x278
obj_cgroup_charge+0x164/0x1d8
kmem_cache_alloc+0xac/0x528
__sigqueue_alloc+0x150/0x308
__send_signal+0x260/0x550
send_signal+0x7e/0x348
force_sig_info_to_task+0x104/0x180
force_sig_fault+0x48/0x58
__do_pgm_check+0x120/0x1f0
pgm_check_handler+0x11e/0x180
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&sighand->siglock);
lock(css_set_lock);
lock(&sighand->siglock);
lock(css_set_lock);
*** DEADLOCK ***
2 locks held by mmap1/202299:
#0: 00000000ca3b3818 (&sighand->siglock){-.-.}-{2:2}, at: force_sig_info_to_task+0x38/0x180
#1: 00000001892ad560 (rcu_read_lock){....}-{1:2}, at: percpu_ref_put_many.constprop.0+0x0/0x168
stack backtrace:
CPU: 15 PID: 202299 Comm: mmap1 Not tainted 5.17.0-20220113.rc0.git0.f2211f194038.300.fc35.s390x+debug #1
Hardware name: IBM 3906 M04 704 (LPAR)
Call Trace:
dump_stack_lvl+0x76/0x98
check_noncircular+0x136/0x158
check_prev_add+0xe0/0xed8
validate_chain+0x736/0xb20
__lock_acquire+0x604/0xbd8
lock_acquire.part.0+0xe2/0x238
lock_acquire+0xb0/0x200
_raw_spin_lock_irqsave+0x6a/0xd8
obj_cgroup_release+0x4a/0xe0
percpu_ref_put_many.constprop.0+0x150/0x168
drain_obj_stock+0x94/0xe8
refill_obj_stock+0x94/0x278
obj_cgroup_charge+0x164/0x1d8
kmem_cache_alloc+0xac/0x528
__sigqueue_alloc+0x150/0x308
__send_signal+0x260/0x550
send_signal+0x7e/0x348
force_sig_info_to_task+0x104/0x180
force_sig_fault+0x48/0x58
__do_pgm_check+0x120/0x1f0
pgm_check_handler+0x11e/0x180
INFO: lockdep is turned off.
In this example a slab allocation from __send_signal() caused a
refilling and draining of a percpu objcg stock, resulted in a releasing
of another non-related objcg. Objcg release path requires taking the
css_set_lock, which is used to synchronize objcg lists.
This can create a circular dependency with the sighandler lock, which is
taken with the locked css_set_lock by the freezer code (to freeze a
task).
In general it seems that using css_set_lock to synchronize objcg lists
makes any slab allocations and deallocation with the locked css_set_lock
and any intervened locks risky.
To fix the problem and make the code more robust let's stop using
css_set_lock to synchronize objcg lists and use a new dedicated spinlock
instead.
Link: https://lkml.kernel.org/r/Yfm1IHmoGdyUR81T@carbon.dhcp.thefacebook.com
Fixes: bf4f059954 ("mm: memcg/slab: obj_cgroup API")
Signed-off-by: Roman Gushchin <guro@fb.com>
Reported-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Tested-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Reviewed-by: Waiman Long <longman@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Reviewed-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The VL805 has a bug in its internal FIFO space accounting that results
in bulk OUT babble if a TRB in a large multi-element TD has a data
buffer size that is larger than and not a multiple of wMaxPacketSize for
the endpoint. If the downstream USB3.0 link is congested, or latency is
increased through an intermediate hub, then the VL805 enters a suspected
FIFO overflow condition and transmits repeated, garbled data to the
endpoint.
TDs with TRBs of exact multiples of wMaxPacketSize and smaller than
wMaxPacketSize appear to be handled correctly, so split buffers at a
1024-byte length boundary and put the remainder in a separate smaller
TRB.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
commit 5f4e5ce638 upstream.
There's list corruption on cgrp_cpuctx_list. This happens on the
following path:
perf_cgroup_switch: list_for_each_entry(cgrp_cpuctx_list)
cpu_ctx_sched_in
ctx_sched_in
ctx_pinned_sched_in
merge_sched_in
perf_cgroup_event_disable: remove the event from the list
Use list_for_each_entry_safe() to allow removing an entry during
iteration.
Fixes: 058fe1c044 ("perf/core: Make cgroup switch visit only cpuctxs with cgroup events")
Signed-off-by: Song Liu <song@kernel.org>
Reviewed-by: Rik van Riel <riel@surriel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20220204004057.2961252-1-song@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 91f6d5f181 upstream.
The port node does not have a unit-address, remove it.
This fixes the warnings:
lcd-controller@30320000: 'port' is a required property
lcd-controller@30320000: 'port@0' does not match any of the regexes:
'pinctrl-[0-9]+'
Fixes: commit d0081bd02a ("arm64: dts: imx8mq: Add NWL MIPI DSI controller")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5852ed2a6a upstream.
Messages around firmware download were incorrectly tagged as being related
to discovery trace events. Thus, firmware download status ended up dumping
the trace log as well as the firmware update message. As there were a
couple of log messages in this state, the trace log was dumped multiple
times.
Resolve this by converting from trace events to SLI events.
Link: https://lore.kernel.org/r/20220207180442.72836-1-jsmart2021@gmail.com
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8375dfac4f upstream.
Commit 43a08c3bda ("can: isotp: isotp_sendmsg(): fix TX buffer concurrent
access in isotp_sendmsg()") introduced a new locking scheme that may render
the userspace application in a locking state when an error is detected.
This issue shows up under high load on simultaneously running isotp channels
with identical configuration which is against the ISO specification and
therefore breaks any reasonable PDU communication anyway.
Fixes: 43a08c3bda ("can: isotp: isotp_sendmsg(): fix TX buffer concurrent access in isotp_sendmsg()")
Link: https://lore.kernel.org/all/20220209073601.25728-1-socketcan@hartkopp.net
Cc: stable@vger.kernel.org
Cc: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1cf5f151d2 upstream.
-Wunaligned-access is a new warning in clang that is default enabled for
arm and arm64 under certain circumstances within the clang frontend (see
LLVM commit below). On v5.17-rc2, an ARCH=arm allmodconfig build shows
1284 total/70 unique instances of this warning (most of the instances
are in header files), which is quite noisy.
To keep a normal build green through CONFIG_WERROR, only show this
warning with W=1, which will allow automated build systems to catch new
instances of the warning so that the total number can be driven down to
zero eventually since catching unaligned accesses at compile time would
be generally useful.
Cc: stable@vger.kernel.org
Link: 35737df4dc
Link: https://github.com/ClangBuiltLinux/linux/issues/1569
Link: https://github.com/ClangBuiltLinux/linux/issues/1576
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0d79987a0 upstream.
When setting the fan speed, i8k_set_fan() calls i8k_get_fan_status(),
causing an unnecessary SMM call since from the two users of this
function, only i8k_ioctl_unlocked() needs to know the new fan status
while dell_smm_write() ignores the new fan status.
Since SMM calls can be very slow while also making error reporting
difficult for dell_smm_write(), remove the function call from
i8k_set_fan() and call it separately in i8k_ioctl_unlocked().
Tested on a Dell Inspiron 3505.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20211021190531.17379-6-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fa77ce201f upstream.
Programmable lab power supplies made by GW Instek, such as the
GPP-2323, have a USB port exposing a serial port to control the device.
Stringing the supplied Windows driver, references to the ch341 chip are
found. Binding the existing ch341 driver to the VID/PID of the GPP-2323
("GW Instek USB2.0-Serial" as per the USB product name) works out of the
box, communication and control is now possible.
This patch should work with any GPP series power supply due to
similarities in the product line.
Signed-off-by: Stephan Brunner <s.brunner@stephan-brunner.net>
Link: https://lore.kernel.org/r/4a47b864-0816-6f6a-efee-aa20e74bcdc6@stephan-brunner.net
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 292d2c82b1 upstream.
Under dummy_hcd, every available endpoint is *either* IN or OUT capable.
But with some real hardware, there are endpoints that support both IN and
OUT. In particular, the PLX 2380 has four available endpoints that each
support both IN and OUT.
raw-gadget currently gets confused and thinks that any endpoint that is
usable as an IN endpoint can never be used as an OUT endpoint.
Fix it by looking at the direction in the configured endpoint descriptor
instead of looking at the hardware capabilities.
With this change, I can use the PLX 2380 with raw-gadget.
Fixes: f2c2e71764 ("usb: gadget: add raw-gadget interface")
Cc: stable <stable@vger.kernel.org>
Tested-by: Andrey Konovalov <andreyknvl@gmail.com>
Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com>
Signed-off-by: Jann Horn <jannh@google.com>
Link: https://lore.kernel.org/r/20220126205214.2149936-1-jannh@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 75e5b4849b upstream.
Stall the control endpoint in case provided index exceeds array size of
MAX_CONFIG_INTERFACES or when the retrieved function pointer is null.
Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 459702eea6 upstream.
The support the external role switch a variety of situations were
addressed, but the transition from USB_ROLE_HOST to USB_ROLE_NONE
leaves the host up which can cause some error messages when
switching from host to none, to gadget, to none, and then back
to host again.
xhci-hcd ee000000.usb: Abort failed to stop command ring: -110
xhci-hcd ee000000.usb: xHCI host controller not responding, assume dead
xhci-hcd ee000000.usb: HC died; cleaning up
usb 4-1: device not accepting address 6, error -108
usb usb4-port1: couldn't allocate usb_device
After this happens it will not act as a host again.
Fix this by releasing the host mode when transitioning to USB_ROLE_NONE.
Fixes: 0604160d8c ("usb: gadget: udc: renesas_usb3: Enhance role switch support")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20220128223603.2362621-1-aford173@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 117b4e96c7 upstream.
With CPU re-ordering on write instructions, there might
be a chance that the HWO is set before the TRB is updated
with the new mapped buffer address.
And in the case where core is processing a list of TRBs
it is possible that it fetched the TRBs when the HWO is set
but before the buffer address is updated.
Prevent this by adding a memory barrier before the HWO
is updated to ensure that the core always process the
updated TRBs.
Fixes: f6bafc6a1c ("usb: dwc3: convert TRBs into bitshifts")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Udipto Goswami <quic_ugoswami@quicinc.com>
Link: https://lore.kernel.org/r/1644207958-18287-1-git-send-email-quic_ugoswami@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 57bc3d3ae8 upstream.
ax88179_rx_fixup() contains several out-of-bounds accesses that can be
triggered by a malicious (or defective) USB device, in particular:
- The metadata array (hdr_off..hdr_off+2*pkt_cnt) can be out of bounds,
causing OOB reads and (on big-endian systems) OOB endianness flips.
- A packet can overlap the metadata array, causing a later OOB
endianness flip to corrupt data used by a cloned SKB that has already
been handed off into the network stack.
- A packet SKB can be constructed whose tail is far beyond its end,
causing out-of-bounds heap data to be considered part of the SKB's
data.
I have tested that this can be used by a malicious USB device to send a
bogus ICMPv6 Echo Request and receive an ICMPv6 Echo Reply in response
that contains random kernel heap data.
It's probably also possible to get OOB writes from this on a
little-endian system somehow - maybe by triggering skb_cow() via IP
options processing -, but I haven't tested that.
Fixes: e2ca90c276 ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver")
Cc: stable@kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 269cbcf7b7 upstream.
When the gadget driver hasn't been (yet) configured, and the cable is
connected to a HOST, the SFTDISCON gets cleared unconditionally, so the
HOST tries to enumerate it.
At the host side, this can result in a stuck USB port or worse. When
getting lucky, some dmesg can be observed at the host side:
new high-speed USB device number ...
device descriptor read/64, error -110
Fix it in drd, by checking the enabled flag before calling
dwc2_hsotg_core_connect(). It will be called later, once configured,
by the normal flow:
- udc_bind_to_driver
- usb_gadget_connect
- dwc2_hsotg_pullup
- dwc2_hsotg_core_connect
Fixes: 17f934024e ("usb: dwc2: override PHY input signals with usb role switch support")
Cc: stable@kernel.org
Reviewed-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/1644423353-17859-1-git-send-email-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0689e46be upstream.
Commit effa453168 ("i2c: i801: Don't silently correct invalid transfer
size") revealed that ee1004_eeprom_read() did not properly limit how
many bytes to read at once.
In particular, i2c_smbus_read_i2c_block_data_or_emulated() takes the
length to read as an u8. If count == 256 after taking into account the
offset and page boundary, the cast to u8 overflows. And this is common
when user space tries to read the entire EEPROM at once.
To fix it, limit each read to I2C_SMBUS_BLOCK_MAX (32) bytes, already
the maximum length i2c_smbus_read_i2c_block_data_or_emulated() allows.
Fixes: effa453168 ("i2c: i801: Don't silently correct invalid transfer size")
Cc: stable@vger.kernel.org
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jonas Malaco <jonas@protocubo.io>
Link: https://lore.kernel.org/r/20220203165024.47767-1-jonas@protocubo.io
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c816b2e65b upstream.
The poll man page says POLLRDNORM is equivalent to POLLIN when used as
an event.
$ man poll
<snip>
POLLRDNORM
Equivalent to POLLIN.
However, in n_tty driver, POLLRDNORM does not return until timeout even
if there is terminal input, whereas POLLIN returns.
The following test program works until kernel-3.17, but the test stops
in poll() after commit 57087d5154 ("tty: Fix spurious poll() wakeups").
[Steps to run test program]
$ cc -o test-pollrdnorm test-pollrdnorm.c
$ ./test-pollrdnorm
foo <-- Type in something from the terminal followed by [RET].
The string should be echoed back.
------------------------< test-pollrdnorm.c >------------------------
#include <stdio.h>
#include <errno.h>
#include <poll.h>
#include <unistd.h>
void main(void)
{
int n;
unsigned char buf[8];
struct pollfd fds[1] = {{ 0, POLLRDNORM, 0 }};
n = poll(fds, 1, -1);
if (n < 0)
perror("poll");
n = read(0, buf, 8);
if (n < 0)
perror("read");
if (n > 0)
write(1, buf, n);
}
------------------------------------------------------------------------
The attached patch fixes this problem. Many calls to
wake_up_interruptible_poll() in the kernel source code already specify
"POLLIN | POLLRDNORM".
Fixes: 57087d5154 ("tty: Fix spurious poll() wakeups")
Cc: stable@vger.kernel.org
Signed-off-by: Kosuke Tatsukawa <tatsu-ab1@nec.com>
Link: https://lore.kernel.org/r/TYCPR01MB81901C0F932203D30E452B3EA5209@TYCPR01MB8190.jpnprd01.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 51a04ebf21 ]
Since struct mv88e6xxx_mdio_bus *mdio_bus is the bus->priv of something
allocated with mdiobus_alloc_size(), this means that mdiobus_free(bus)
will free the memory backing the mdio_bus as well. Therefore, the
mdio_bus->list element is freed memory, but we continue to iterate
through the list of MDIO buses using that list element.
To fix this, use the proper list iterator that handles element deletion
by keeping a copy of the list element next pointer.
Fixes: f53a2ce893 ("net: dsa: mv88e6xxx: don't use devres for mdiobus")
Reported-by: Rafael Richter <rafael.richter@gin.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220210174017.3271099-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46b699c50c ]
The driver was avoiding offload for IPIP (at least) frames due to
parsing the inner header offsets incorrectly when trying to check
lengths.
This length check works for VXLAN frames but fails on IPIP frames
because skb_transport_offset points to the inner header in IPIP
frames, which meant the subtraction of transport_header from
inner_network_header returns a negative value (-20).
With the code before this patch, everything continued to work, but GSO
was being used to segment, causing throughputs of 1.5Gb/s per thread.
After this patch, throughput is more like 10Gb/s per thread for IPIP
traffic.
Fixes: e94d447866 ("ice: Implement filter sync, NDO operations and bump version")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ccc6e0c89 ]
The netdev should be unregistered before we are disconnecting from the
MAC/PHY so that the dev_close callback is called and the PHY and the
phylink workqueues are actually stopped before we are disconnecting and
destroying the phylink instance.
Fixes: 7194792308 ("dpaa2-eth: add MAC/PHY support through phylink")
Signed-off-by: Robert-Ionut Alexa <robert-ionut.alexa@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68c2d6af1f ]
Hardware interrupts are enabled during the pci probe, however,
they are not disabled during pci removal.
Disable all hardware interrupts during pci removal to avoid any
issues.
Fixes: e753774047 ("amd-xgbe: Update PCI support to use new IRQ functions")
Suggested-by: Selwin Sebastian <Selwin.Sebastian@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7223d6877 ]
It would be easy to craft a message containing an illegal binding table
update operation. This is handled correctly by the code, but the
corresponding warning printout is not rate limited as is should be.
We fix this now.
Fixes: b97bf3fd8f ("[TIPC] Initial merge")
Signed-off-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9eeabdf17f ]
When uncloning an skb dst and its associated metadata, a new
dst+metadata is allocated and later replaces the old one in the skb.
This is helpful to have a non-shared dst+metadata attached to a specific
skb.
The issue is the uncloned dst+metadata is initialized with a refcount of
1, which is increased to 2 before attaching it to the skb. When
tun_dst_unclone returns, the dst+metadata is only referenced from a
single place (the skb) while its refcount is 2. Its refcount will never
drop to 0 (when the skb is consumed), leading to a memory leak.
Fix this by removing the call to dst_hold in tun_dst_unclone, as the
dst+metadata refcount is already 1.
Fixes: fc4099f172 ("openvswitch: Fix egress tunnel info.")
Cc: Pravin B Shelar <pshelar@ovn.org>
Reported-by: Vlad Buslov <vladbu@nvidia.com>
Tested-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cfc56f85e7 ]
When uncloning an skb dst and its associated metadata a new dst+metadata
is allocated and the tunnel information from the old metadata is copied
over there.
The issue is the tunnel metadata has references to cached dst, which are
copied along the way. When a dst+metadata refcount drops to 0 the
metadata is freed including the cached dst entries. As they are also
referenced in the initial dst+metadata, this ends up in UaFs.
In practice the above did not happen because of another issue, the
dst+metadata was never freed because its refcount never dropped to 0
(this will be fixed in a subsequent patch).
Fix this by initializing the dst cache after copying the tunnel
information from the old metadata to also unshare the dst cache.
Fixes: d71785ffc7 ("net: add dst_cache to ovs vxlan lwtunnel")
Cc: Paolo Abeni <pabeni@redhat.com>
Reported-by: Vlad Buslov <vladbu@nvidia.com>
Tested-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7db788ad62 ]
When looking for a global mac index the extra NFP_TUN_PRE_TUN_IDX_BIT
that gets set if nfp_flower_is_supported_bridge is true is not taken
into account. Consequently the path that should release the ida_index
in cleanup is never triggered, causing messages like:
nfp 0000:02:00.0: nfp: Failed to offload MAC on br-ex.
nfp 0000:02:00.0: nfp: Failed to offload MAC on br-ex.
nfp 0000:02:00.0: nfp: Failed to offload MAC on br-ex.
after NFP_MAX_MAC_INDEX number of reconfigs. Ultimately this lead to
new tunnel flows not being offloaded.
Fix this by unsetting the NFP_TUN_PRE_TUN_IDX_BIT before checking if
the port is of type OTHER.
Fixes: 2e0bc7f3cb ("nfp: flower: encode mac indexes with pre-tunnel rule check")
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220208101453.321949-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d120dfb5d ]
As explained in commits:
74b6d7d133 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3d ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The GSWIP switch is a platform device, so the initial set of constraints
that I thought would cause this (I2C or SPI buses which call ->remove on
->shutdown) do not apply. But there is one more which applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the GSWIP switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The gswip driver has the code structure in place for orderly mdiobus
removal, so just replace devm_mdiobus_alloc() with the non-devres
variant, and add manual free where necessary, to ensure that we don't
let devres free a still-registered bus.
Fixes: ac3a68d566 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 209bdb7ec6 ]
As explained in commits:
74b6d7d133 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3d ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The Felix VSC9959 switch is a PCI device, so the initial set of
constraints that I thought would cause this (I2C or SPI buses which call
->remove on ->shutdown) do not apply. But there is one more which
applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the felix switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The felix driver has the code structure in place for orderly mdiobus
removal, so just replace devm_mdiobus_alloc_size() with the non-devres
variant, and add manual free where necessary, to ensure that we don't
let devres free a still-registered bus.
Fixes: ac3a68d566 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08f1a20822 ]
As explained in commits:
74b6d7d133 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3d ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The Starfighter 2 is a platform device, so the initial set of
constraints that I thought would cause this (I2C or SPI buses which call
->remove on ->shutdown) do not apply. But there is one more which
applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the bcm_sf2 switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The bcm_sf2 driver has the code structure in place for orderly mdiobus
removal, so just replace devm_mdiobus_alloc() with the non-devres
variant, and add manual free where necessary, to ensure that we don't
let devres free a still-registered bus.
Fixes: ac3a68d566 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50facd86e9 ]
As explained in commits:
74b6d7d133 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3d ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The ar9331 is an MDIO device, so the initial set of constraints that I
thought would cause this (I2C or SPI buses which call ->remove on
->shutdown) do not apply. But there is one more which applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the ar9331 switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The ar9331 driver doesn't have a complex code structure for mdiobus
removal, so just replace of_mdiobus_register with the devres variant in
order to be all-devres and ensure that we don't free a still-registered
bus.
Fixes: ac3a68d566 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f53a2ce893 ]
As explained in commits:
74b6d7d133 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3d ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The mv88e6xxx is an MDIO device, so the initial set of constraints that
I thought would cause this (I2C or SPI buses which call ->remove on
->shutdown) do not apply. But there is one more which applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the Marvell switch driver on shutdown.
systemd-shutdown[1]: Powering off.
mv88e6085 0x0000000008b96000:00 sw_gl0: Link is Down
fsl-mc dpbp.9: Removing from iommu group 7
fsl-mc dpbp.8: Removing from iommu group 7
------------[ cut here ]------------
kernel BUG at drivers/net/phy/mdio_bus.c:677!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 1 Comm: systemd-shutdow Not tainted 5.16.5-00040-gdc05f73788e5 #15
pc : mdiobus_free+0x44/0x50
lr : devm_mdiobus_free+0x10/0x20
Call trace:
mdiobus_free+0x44/0x50
devm_mdiobus_free+0x10/0x20
devres_release_all+0xa0/0x100
__device_release_driver+0x190/0x220
device_release_driver_internal+0xac/0xb0
device_links_unbind_consumers+0xd4/0x100
__device_release_driver+0x4c/0x220
device_release_driver_internal+0xac/0xb0
device_links_unbind_consumers+0xd4/0x100
__device_release_driver+0x94/0x220
device_release_driver+0x28/0x40
bus_remove_device+0x118/0x124
device_del+0x174/0x420
fsl_mc_device_remove+0x24/0x40
__fsl_mc_device_remove+0xc/0x20
device_for_each_child+0x58/0xa0
dprc_remove+0x90/0xb0
fsl_mc_driver_remove+0x20/0x5c
__device_release_driver+0x21c/0x220
device_release_driver+0x28/0x40
bus_remove_device+0x118/0x124
device_del+0x174/0x420
fsl_mc_bus_remove+0x80/0x100
fsl_mc_bus_shutdown+0xc/0x1c
platform_shutdown+0x20/0x30
device_shutdown+0x154/0x330
kernel_power_off+0x34/0x6c
__do_sys_reboot+0x15c/0x250
__arm64_sys_reboot+0x20/0x30
invoke_syscall.constprop.0+0x4c/0xe0
do_el0_svc+0x4c/0x150
el0_svc+0x24/0xb0
el0t_64_sync_handler+0xa8/0xb0
el0t_64_sync+0x178/0x17c
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The Marvell driver already has a good structure for mdiobus removal, so
just plug in mdiobus_free and get rid of devres.
Fixes: ac3a68d566 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Reported-by: Rafael Richter <Rafael.Richter@gin.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Daniel Klauer <daniel.klauer@gin.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23de0d7b6f ]
When 803.2ad mode enables a participating port, it should update
the slave-array. I have observed that the member links are participating
and are part of the active aggregator while the traffic is egressing via
only one member link (in a case where two links are participating). Via
kprobes I discovered that slave-arr has only one link added while
the other participating link wasn't part of the slave-arr.
I couldn't see what caused that situation but the simple code-walk
through provided me hints that the enable_port wasn't always associated
with the slave-array update.
Fixes: ee63771474 ("bonding: Simplify the xmit function for modes that use xmit_hash")
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/20220207222901.1795287-1-maheshb@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc38ef9368 ]
Setting the output of a GPIO to 1 using gpiod_set_value(), followed by
reading the same GPIO using gpiod_get_value(), will currently yield an
incorrect result.
This is because the SiFive GPIO device stores the output values in reg_set,
not reg_dat.
Supply the flag BGPIOF_READ_OUTPUT_REG_SET to bgpio_init() so that the
generic driver reads the correct register.
Fixes: 96868dce64 ("gpio/sifive: Add GPIO driver for SiFive SoCs")
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
[Bartosz: added the Fixes tag]
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc0075ba7f ]
Commit 4a9af6cac0 ("ACPI: EC: Rework flushing of EC work while
suspended to idle") made acpi_ec_dispatch_gpe() check
pm_wakeup_pending(), but that is before canceling the SCI wakeup,
so pm_wakeup_pending() is always true. This causes the loop in
acpi_ec_dispatch_gpe() to always terminate after one iteration which
may not be correct.
Address this issue by canceling the SCI wakeup earlier, from
acpi_ec_dispatch_gpe() itself.
Fixes: 4a9af6cac0 ("ACPI: EC: Rework flushing of EC work while suspended to idle")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe68195daf ]
From 4.17 onwards the ixgbevf driver uses build_skb() to build an skb
around new data in the page buffer shared with the ixgbe PF.
This uses either a 2K or 3K buffer, and offsets the DMA mapping by
NET_SKB_PAD + NET_IP_ALIGN. When using a smaller buffer RXDCTL is set to
ensure the PF does not write a full 2K bytes into the buffer, which is
actually 2K minus the offset.
However on the 82599 virtual function, the RXDCTL mechanism is not
available. The driver attempts to work around this by using the SET_LPE
mailbox method to lower the maximm frame size, but the ixgbe PF driver
ignores this in order to keep the PF and all VFs in sync[0].
This means the PF will write up to the full 2K set in SRRCTL, causing it
to write NET_SKB_PAD + NET_IP_ALIGN bytes past the end of the buffer.
With 4K pages split into two buffers, this means it either writes
NET_SKB_PAD + NET_IP_ALIGN bytes past the first buffer (and into the
second), or NET_SKB_PAD + NET_IP_ALIGN bytes past the end of the DMA
mapping.
Avoid this by only enabling build_skb when using "large" buffers (3K).
These are placed in each half of an order-1 page, preventing the PF from
writing past the end of the mapping.
[0]: Technically it only ever raises the max frame size, see
ixgbe_set_vf_lpe() in ixgbe_sriov.c
Fixes: f15c5ba5b6 ("ixgbevf: add support for using order 1 pages to receive large frames")
Signed-off-by: Samuel Mendoza-Jonas <samjonas@amazon.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1ca60efc5 ]
When userspace, e.g. conntrackd, inserts an entry with a specified helper,
its possible that the helper is lost immediately after its added:
ctnetlink_create_conntrack
-> nf_ct_helper_ext_add + assign helper
-> ctnetlink_setup_nat
-> ctnetlink_parse_nat_setup
-> parse_nat_setup -> nfnetlink_parse_nat_setup
-> nf_nat_setup_info
-> nf_conntrack_alter_reply
-> __nf_ct_try_assign_helper
... and __nf_ct_try_assign_helper will zero the helper again.
Set IPS_HELPER bit to bypass auto-assign logic, its unwanted, just like
when helper is assigned via ruleset.
Dropped old 'not strictly necessary' comment, it referred to use of
rcu_assign_pointer() before it got replaced by RCU_INIT_POINTER().
NB: Fixes tag intentionally incorrect, this extends the referenced commit,
but this change won't build without IPS_HELPER introduced there.
Fixes: 6714cf5465 ("netfilter: nf_conntrack: fix explicit helper attachment and NAT")
Reported-by: Pham Thanh Tuyen <phamtyn@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46963e2e06 ]
If the copy back to userland fails for the FASTRPC_IOCTL_ALLOC_DMA_BUFF
ioctl(), we shouldn't assume that 'buf->dmabuf' is still valid. In fact,
dma_buf_fd() called fd_install() before, i.e. "consumed" one reference,
leaving us with none.
Calling dma_buf_put() will therefore put a reference we no longer own,
leading to a valid file descritor table entry for an already released
'file' object which is a straight use-after-free.
Simply avoid calling dma_buf_put() and rely on the process exit code to
do the necessary cleanup, if needed, i.e. if the file descriptor is
still valid.
Fixes: 6cffd79504 ("misc: fastrpc: Add support for dmabuf exporter")
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Mathias Krause <minipli@grsecurity.net>
Link: https://lore.kernel.org/r/20220127130218.809261-1-minipli@grsecurity.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d11896596 ]
The 2711 pixel valve can't produce odd horizontal timings, and
checks were added to vc4_hdmi_encoder_atomic_check and
vc4_hdmi_encoder_mode_valid to filter out/block selection of
such modes.
Modes with DRM_MODE_FLAG_DBLCLK double all the horizontal timing
values before programming them into the PV. The PV values,
therefore, can not be odd, and so the modes can be supported.
Amend the filtering appropriately.
Fixes: 57fb32e632 ("drm/vc4: hdmi: Block odd horizontal timings")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220127135116.298278-1-maxime@cerno.tech
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2cba05451a ]
If the parent GPIO controller is a sleeping controller (e.g. a GPIO
controller connected to I2C), getting or setting a GPIO triggers a
might_sleep() warning. This happens because the GPIO Aggregator takes
the can_sleep flag into account only for its internal locking, not for
calling into the parent GPIO controller.
Fix this by using the gpiod_[gs]et*_cansleep() APIs when calling into a
sleeping GPIO controller.
Reported-by: Mikko Salomäki <ms@datarespons.se>
Fixes: 828546e242 ("gpio: Add GPIO Aggregator")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ebe2b1add1 ]
Consider a case where ffs_func_eps_disable is called from
ffs_func_disable as part of composition switch and at the
same time ffs_epfile_release get called from userspace.
ffs_epfile_release will free up the read buffer and call
ffs_data_closed which in turn destroys ffs->epfiles and
mark it as NULL. While this was happening the driver has
already initialized the local epfile in ffs_func_eps_disable
which is now freed and waiting to acquire the spinlock. Once
spinlock is acquired the driver proceeds with the stale value
of epfile and tries to free the already freed read buffer
causing use-after-free.
Following is the illustration of the race:
CPU1 CPU2
ffs_func_eps_disable
epfiles (local copy)
ffs_epfile_release
ffs_data_closed
if (last file closed)
ffs_data_reset
ffs_data_clear
ffs_epfiles_destroy
spin_lock
dereference epfiles
Fix this races by taking epfiles local copy & assigning it under
spinlock and if epfiles(local) is null then update it in ffs->epfiles
then finally destroy it.
Extending the scope further from the race, protecting the ep related
structures, and concurrent accesses.
Fixes: a9e6f83c2d ("usb: gadget: f_fs: stop sleeping in ffs_func_eps_disable")
Co-developed-by: Udipto Goswami <quic_ugoswami@quicinc.com>
Reviewed-by: John Keeping <john@metanate.com>
Signed-off-by: Pratham Pratap <quic_ppratap@quicinc.com>
Signed-off-by: Udipto Goswami <quic_ugoswami@quicinc.com>
Link: https://lore.kernel.org/r/1643256595-10797-1-git-send-email-quic_ugoswami@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d58c5e21a ]
The correct property name is 'assigned-clock-parents', not
'assigned-clocks-parents'. Though if the platform works with the typo, one
has to wonder if the property is even needed.
Signed-off-by: Rob Herring <robh@kernel.org>
Fixes: 8b8c7d97e2 ("ARM: dts: imx7ulp: Add wdog1 node")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37291f60d0 ]
TX_PROT_BUS_WIDTH and RX_PROT_BUS_WIDTH are single registers with
separate bit fields for each lane. The code in xpsgtr_phy_init_sgmii was
not preserving the existing register value for other lanes, so enabling
the PHY in SGMII mode on one lane zeroed out the settings for all other
lanes, causing other PS-GTR peripherals such as USB3 to malfunction.
Use xpsgtr_clr_set to only manipulate the desired bits in the register.
Fixes: 4a33bea003 ("phy: zynqmp: Add PHY driver for the Xilinx ZynqMP Gigabit Transceiver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20220126001600.1592218-1-robert.hancock@calian.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3375aa7713 ]
The dt-bindings for the UART controller only allow the following values
for Meson8 SoCs:
- "amlogic,meson8b-uart", "amlogic,meson-ao-uart"
- "amlogic,meson8b-uart"
Use the correct fallback compatible string "amlogic,meson-ao-uart" for
AO UART. Drop the "amlogic,meson-uart" compatible string from the EE
domain UART controllers.
Also update the order of the clocks to match the order defined in the
yaml bindings.
Fixes: b02d6e73f5 ("ARM: dts: meson8b: use stable UART bindings with correct gate clock")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20211227180026.4068352-4-martin.blumenstingl@googlemail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57007bfb54 ]
The dt-bindings for the UART controller only allow the following values
for Meson8 SoCs:
- "amlogic,meson8-uart", "amlogic,meson-ao-uart"
- "amlogic,meson8-uart"
Use the correct fallback compatible string "amlogic,meson-ao-uart" for
AO UART. Drop the "amlogic,meson-uart" compatible string from the EE
domain UART controllers.
Also update the order of the clocks to match the order defined in the
yaml schema.
Fixes: 6ca7750205 ("ARM: dts: meson8: use stable UART bindings with correct gate clock")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20211227180026.4068352-3-martin.blumenstingl@googlemail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23885389db ]
Commit e428e250fd ("ARM: dts: Configure system timers for omap3")
caused a timer regression for beagleboard revision c where the system
clockevent stops working if omap3isp module is unloaded.
Turns out we still have beagleboard revisions a-b4 capacitor c70 quirks
applied that limit the usable timers for no good reason. This also affects
the power management as we use the system clock instead of the 32k clock
source.
Let's fix the issue by adding a new omap3-beagle-ab4.dts for the old timer
quirks. This allows us to remove the timer quirks for later beagleboard
revisions. We also need to update the related timer quirk check for the
correct compatible property.
Fixes: e428e250fd ("ARM: dts: Configure system timers for omap3")
Cc: linux-kernel@vger.kernel.org
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <robh+dt@kernel.org>
Reported-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9da1e9ab82 upstream.
Commit 7707f7227f ("drm/rockchip: Add support for afbc") switched up
the rk3399_vop_big[] register windows, but it did so incorrectly.
The biggest problem is in rk3288_win23_data[] vs.
rk3368_win23_data[] .format field:
RK3288's format: VOP_REG(RK3288_WIN2_CTRL0, 0x7, 1)
RK3368's format: VOP_REG(RK3368_WIN2_CTRL0, 0x3, 5)
Bits 5:6 (i.e., shift 5, mask 0x3) are correct for RK3399, according to
the TRM.
There are a few other small differences between the 3288 and 3368
definitions that were swapped in commit 7707f7227f. I reviewed them to
the best of my ability according to the RK3399 TRM and fixed them up.
This fixes IOMMU issues (and display errors) when testing with BG24
color formats.
Fixes: 7707f7227f ("drm/rockchip: Add support for afbc")
Cc: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Tested-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220119161104.1.I1d01436bef35165a8cdfe9308789c0badb5ff46a@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cb1f65c1e1 upstream.
After commit e3728b50cd ("ACPI: PM: s2idle: Avoid possible race
related to the EC GPE") wakeup interrupts occurring immediately after
the one discarded by acpi_s2idle_wake() may be missed. Moreover, if
the SCI triggers again immediately after the rearming in
acpi_s2idle_wake(), that wakeup may be missed too.
The problem is that pm_system_irq_wakeup() only calls pm_system_wakeup()
when pm_wakeup_irq is 0, but that's not the case any more after the
interrupt causing acpi_s2idle_wake() to run until pm_wakeup_irq is
cleared by the pm_wakeup_clear() call in s2idle_loop(). However,
there may be wakeup interrupts occurring in that time frame and if
that happens, they will be missed.
To address that issue first move the clearing of pm_wakeup_irq to
the point at which it is known that the interrupt causing
acpi_s2idle_wake() to tun will be discarded, before rearming the SCI
for wakeup. Moreover, because that only reduces the size of the
time window in which the issue may manifest itself, allow
pm_system_irq_wakeup() to register two second wakeup interrupts in
a row and, when discarding the first one, replace it with the second
one. [Of course, this assumes that only one wakeup interrupt can be
discarded in one go, but currently that is the case and I am not
aware of any plans to change that.]
Fixes: e3728b50cd ("ACPI: PM: s2idle: Avoid possible race related to the EC GPE")
Cc: 5.4+ <stable@vger.kernel.org> # 5.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da5fb9e1ad upstream.
The original version of the IORT PMCG definition had an oversight
wherein there was no way to describe the second register page for an
implementation using the recommended RELOC_CTRS feature. Although the
spec was fixed, and the final patches merged to ACPICA and Linux written
against the new version, it seems that some old firmware based on the
original revision has survived and turned up in the wild.
Add a check for the original PMCG definition, and avoid filling in the
second memory resource with nonsense if so. Otherwise it is likely that
something horrible will happen when the PMCG driver attempts to probe.
Reported-by: Michael Petlan <mpetlan@redhat.com>
Fixes: 24e5160493 ("ACPI/IORT: Add support for PMCG")
Cc: <stable@vger.kernel.org> # 5.2.x
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Link: https://lore.kernel.org/r/75628ae41c257fb73588f7bf1c4459160e04be2b.1643916258.git.robin.murphy@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63573807b2 upstream.
AER is not backed by a real request, hence we should not incorrectly
assume that when failing to send a nvme command, it is a normal request
but rather check if this is an aer and if so complete the aer (similar
to the normal completion path).
Cc: stable@vger.kernel.org
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3037b174b1 upstream.
The SocFPGA machine since commit b3ca9888f3 ("reset: socfpga: add an
early reset driver for SoCFPGA") uses reset controller, so it should
select RESET_CONTROLLER explicitly. Selecting ARCH_HAS_RESET_CONTROLLER
is not enough because it affects only default choice still allowing a
non-buildable configuration:
/usr/bin/arm-linux-gnueabi-ld: arch/arm/mach-socfpga/socfpga.o: in function `socfpga_init_irq':
arch/arm/mach-socfpga/socfpga.c:56: undefined reference to `socfpga_reset_init'
Reported-by: kernel test robot <lkp@intel.com>
Cc: <stable@vger.kernel.org>
Fixes: b3ca9888f3 ("reset: socfpga: add an early reset driver for SoCFPGA")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42c9b28e68 upstream.
Currently, SD card fails to mount due to the following pinctrl error:
[ 11.170000] imx23-pinctrl 80018000.pinctrl: pin SSP1_DETECT already requested by 80018000.pinctrl; cannot claim for 80010000.spi
[ 11.180000] imx23-pinctrl 80018000.pinctrl: pin-65 (80010000.spi) status -22
[ 11.190000] imx23-pinctrl 80018000.pinctrl: could not request pin 65 (SSP1_DETECT) from group mmc0-pins-fixup.0 on device 80018000.pinctrl
[ 11.200000] mxs-mmc 80010000.spi: Error applying setting, reverse things back
Fix it by removing the MX23_PAD_SSP1_DETECT pin from the hog group as it
is already been used by the mmc0-pins-fixup pinctrl group.
With this change the rootfs can be mounted and the imx23-evk board can
boot successfully.
Cc: <stable@vger.kernel.org>
Fixes: bc3875f1a6 ("ARM: dts: mxs: modify mx23/mx28 dts files to use pinctrl headers")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6df2a016c0 upstream.
From version 2.38, binutils default to ISA spec version 20191213. This
means that the csr read/write (csrr*/csrw*) instructions and fence.i
instruction has separated from the `I` extension, become two standalone
extensions: Zicsr and Zifencei. As the kernel uses those instruction,
this causes the following build failure:
CC arch/riscv/kernel/vdso/vgettimeofday.o
<<BUILDDIR>>/arch/riscv/include/asm/vdso/gettimeofday.h: Assembler messages:
<<BUILDDIR>>/arch/riscv/include/asm/vdso/gettimeofday.h:71: Error: unrecognized opcode `csrr a5,0xc01'
<<BUILDDIR>>/arch/riscv/include/asm/vdso/gettimeofday.h:71: Error: unrecognized opcode `csrr a5,0xc01'
<<BUILDDIR>>/arch/riscv/include/asm/vdso/gettimeofday.h:71: Error: unrecognized opcode `csrr a5,0xc01'
<<BUILDDIR>>/arch/riscv/include/asm/vdso/gettimeofday.h:71: Error: unrecognized opcode `csrr a5,0xc01'
The fix is to specify those extensions explicitely in -march. However as
older binutils version do not support this, we first need to detect
that.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Tested-by: Alexandre Ghiti <alexandre.ghiti@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b9bed78e2f ]
Set vmcs.GUEST_PENDING_DBG_EXCEPTIONS.BS, a.k.a. the pending single-step
breakpoint flag, when re-injecting a #DB with RFLAGS.TF=1, and STI or
MOVSS blocking is active. Setting the flag is necessary to make VM-Entry
consistency checks happy, as VMX has an invariant that if RFLAGS.TF is
set and STI/MOVSS blocking is true, then the previous instruction must
have been STI or MOV/POP, and therefore a single-step #DB must be pending
since the RFLAGS.TF cannot have been set by the previous instruction,
i.e. the one instruction delay after setting RFLAGS.TF must have already
expired.
Normally, the CPU sets vmcs.GUEST_PENDING_DBG_EXCEPTIONS.BS appropriately
when recording guest state as part of a VM-Exit, but #DB VM-Exits
intentionally do not treat the #DB as "guest state" as interception of
the #DB effectively makes the #DB host-owned, thus KVM needs to manually
set PENDING_DBG.BS when forwarding/re-injecting the #DB to the guest.
Note, although this bug can be triggered by guest userspace, doing so
requires IOPL=3, and guest userspace running with IOPL=3 has full access
to all I/O ports (from the guest's perspective) and can crash/reboot the
guest any number of ways. IOPL=3 is required because STI blocking kicks
in if and only if RFLAGS.IF is toggled 0=>1, and if CPL>IOPL, STI either
takes a #GP or modifies RFLAGS.VIF, not RFLAGS.IF.
MOVSS blocking can be initiated by userspace, but can be coincident with
a #DB if and only if DR7.GD=1 (General Detect enabled) and a MOV DR is
executed in the MOVSS shadow. MOV DR #GPs at CPL>0, thus MOVSS blocking
is problematic only for CPL0 (and only if the guest is crazy enough to
access a DR in a MOVSS shadow). All other sources of #DBs are either
suppressed by MOVSS blocking (single-step, code fetch, data, and I/O),
are mutually exclusive with MOVSS blocking (T-bit task switch), or are
already handled by KVM (ICEBP, a.k.a. INT1).
This bug was originally found by running tests[1] created for XSA-308[2].
Note that Xen's userspace test emits ICEBP in the MOVSS shadow, which is
presumably why the Xen bug was deemed to be an exploitable DOS from guest
userspace. KVM already handles ICEBP by skipping the ICEBP instruction
and thus clears MOVSS blocking as a side effect of its "emulation".
[1] http://xenbits.xenproject.org/docs/xtf/xsa-308_2main_8c_source.html
[2] https://xenbits.xen.org/xsa/advisory-308.html
Reported-by: David Woodhouse <dwmw2@infradead.org>
Reported-by: Alexander Graf <graf@amazon.de>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220120000624.655815-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdf85e0c5d ]
Inject a #GP instead of synthesizing triple fault to try to avoid killing
the guest if emulation of an SEV guest fails due to encountering the SMAP
erratum. The injected #GP may still be fatal to the guest, e.g. if the
userspace process is providing critical functionality, but KVM should
make every attempt to keep the guest alive.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Message-Id: <20220120010719.711476-10-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f80ae0ef08 ]
Similar to MSR_IA32_VMX_EXIT_CTLS/MSR_IA32_VMX_TRUE_EXIT_CTLS,
MSR_IA32_VMX_ENTRY_CTLS/MSR_IA32_VMX_TRUE_ENTRY_CTLS pair,
MSR_IA32_VMX_TRUE_PINBASED_CTLS needs to be filtered the same way
MSR_IA32_VMX_PINBASED_CTLS is currently filtered as guests may solely rely
on 'true' MSR data.
Note, none of the currently existing Windows/Hyper-V versions are known
to stumble upon the unfiltered MSR_IA32_VMX_TRUE_PINBASED_CTLS, the change
is aimed at making the filtering future proof.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20220112170134.1904308-2-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a601e2cf6 ]
Enlightened VMCS v1 doesn't have VMX_PREEMPTION_TIMER_VALUE field,
PIN_BASED_VMX_PREEMPTION_TIMER is also filtered out already so it makes
sense to filter out VM_EXIT_SAVE_VMX_PREEMPTION_TIMER too.
Note, none of the currently existing Windows/Hyper-V versions are known
to enable 'save VMX-preemption timer value' when eVMCS is in use, the
change is aimed at making the filtering future proof.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20220112170134.1904308-3-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e0db41e7a ]
When readl_poll_timeout() timeout, we'd better directly use its return
value.
Before this patch:
[ 2.145528] dwmac-sun8i: probe of 4500000.ethernet failed with error -14
After this patch:
[ 2.138520] dwmac-sun8i: probe of 4500000.ethernet failed with error -110
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 25e58af4be ]
The Intel P4500/P4600 SSDs do not report a subsystem NQN despite claiming
compliance to a standards version where reporting one is required.
Add the IGNORE_DEV_SUBNQN quirk to not fail the initialization of a
second such SSDs in a system.
Signed-off-by: Zheng Wu <wu.zheng@intel.com>
Signed-off-by: Ye Jinhe <jinhe.ye@intel.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 961c391217 ]
When using per-process mode and event inheritance is set to true,
forked processes will create a new perf events via inherit_event() ->
perf_event_alloc(). But these events will not have ring buffers
assigned to them. Any call to wakeup will be dropped if it's called on
an event with no ring buffer assigned because that's the object that
holds the wakeup list.
If the child event is disabled due to a call to
perf_aux_output_begin() or perf_aux_output_end(), the wakeup is
dropped leaving userspace hanging forever on the poll.
Normally the event is explicitly re-enabled by userspace after it
wakes up to read the aux data, but in this case it does not get woken
up so the event remains disabled.
This can be reproduced when using Arm SPE and 'stress' which forks once
before running the workload. By looking at the list of aux buffers read,
it's apparent that they stop after the fork:
perf record -e arm_spe// -vvv -- stress -c 1
With this patch applied they continue to be printed. This behaviour
doesn't happen when using systemwide or per-cpu mode.
Reported-by: Ruben Ayrapetyan <Ruben.Ayrapetyan@arm.com>
Signed-off-by: James Clark <james.clark@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20211206113840.130802-2-james.clark@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac55d16385 ]
Calling dwc2_hsotg_ep_disable on ep0 (in/out) will lead to the following
logs before returning -EINVAL:
dwc2 49000000.usb-otg: dwc2_hsotg_ep_disable: called for ep0
dwc2 49000000.usb-otg: dwc2_hsotg_ep_disable: called for ep0
To avoid these two logs while suspending, start disabling the endpoint
from the index 1, as done in dwc2_hsotg_udc_stop:
/* all endpoints should be shutdown */
for (ep = 1; ep < hsotg->num_of_eps; ep++) {
if (hsotg->eps_in[ep])
dwc2_hsotg_ep_disable_lock(&hsotg->eps_in[ep]->ep);
if (hsotg->eps_out[ep])
dwc2_hsotg_ep_disable_lock(&hsotg->eps_out[ep]->ep);
}
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211207130101.270314-1-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 33569ef3c7 ]
It is an unused wrapper forcing kmalloc allocation for registering
nosave regions. Also, rename __register_nosave_region() to
register_nosave_region() now that there is no need for disambiguation.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62afb379a0 ]
According to the comment in check_fw_ready() we should not check the
IOP1_READY field in register SCRATCH_PAD_1 for 8008 or 8009 controllers.
However we check this very field in process_oq() for processing the highest
index interrupt vector. The highest interrupt vector is checked as the FW
is programmed to signal fatal errors through this irq.
Change that function to not check IOP1_READY for those mentioned
controllers, but do check ILA_READY in both cases.
The reason I assume that this was not hit earlier was because we always
allocated 64 MSI(X), and just did not pass the vector index check in
process_oq(), i.e. the handler never ran for vector index 63.
Link: https://lore.kernel.org/r/1642508105-95432-1-git-send-email-john.garry@huawei.com
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 973bf8fdd1 ]
When adding a tc rule with a qdisc kind that is not supported or not
compiled into the kernel, the kernel emits the following error: "Error:
Specified qdisc not found.". Found via tdc testing when ETS qdisc was not
compiled in and it was not obvious right away what the message meant
without looking at the kernel code.
Change the error message to be more explicit and say the qdisc kind is
unknown.
Signed-off-by: Victor Nogueira <victor@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8d54baba7 ]
An fs_location attribute returns a string that can be ipv4, ipv6,
or DNS name. An ip location can have a port appended to it and if
no port is present a default port needs to be set. If rpc_pton()
fails to parse, try calling rpc_uaddr2socaddr() that can convert
an universal address.
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90e12a3191 ]
Remove the check for the zero length fs_locations reply in the
xdr decoding, and instead check for that in the migration code.
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b05bf5c63b ]
When decode_devicenotify_args() exits with no entries, we need to
ensure that the struct cb_devicenotifyargs is initialised to
{ 0, NULL } in order to avoid problems in
nfs4_callback_devicenotify().
Reported-by: <rtm@csail.mit.edu>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fbd2057e53 ]
kstrdup() returns NULL when some internal memory errors happen, it is
better to check the return value of it so to catch the memory error in
time.
Signed-off-by: Xiaoke Wang <xkernel.wang@foxmail.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c52c8376d ]
When the bitmask of the attributes doesn't include the security label,
don't bother printing it. Since the label might not be null terminated,
adjust the printing format accordingly.
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b5e7b59c34 ]
Currently the nfs_access_get_cached family of functions report a
'struct nfs_access_entry' as the result, with both .mask and .cred set.
However the .cred is never used. This is probably good and there is no
guarantee that it won't be freed before use.
Change to only report the 'mask' - as this is all that is used or needed.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6a4d333d54 upstream.
NFSv3 and NFSv4 use u64 offset values on the wire. Record these values
verbatim without the implicit type case to loff_t.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6260d9a56a upstream.
Ensure that a client cannot specify a WRITE range that falls in a
byte range outside what the kernel's internal types (such as loff_t,
which is signed) can represent. The kiocb iterators, invoked in
nfsd_vfs_write(), should properly limit write operations to within
the underlying file system's s_maxbytes.
Cc: stable@vger.kernel.org
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 468d126dab upstream.
For some long forgotten reason, the nfs_client cl_flags field is
initialised in nfs_get_client() instead of being initialised at
allocation time. This quirk was harmless until we moved the call to
nfs_create_rpc_client().
Fixes: dd99e9f98f ("NFSv4: Initialise connection to the server in nfs4_alloc_client()")
Cc: stable@vger.kernel.org # 4.8.x
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aec12836e7 upstream.
When setting up autonegotiation for 88E1118R and compatible PHYs,
a software reset of PHY is issued before setting up polarity.
This is incorrect as changes of MDI Crossover Mode bits are
disruptive to the normal operation and must be followed by a
software reset to take effect. Let's patch m88e1118_config_aneg()
to fix the issue mentioned before by invoking software reset
of the PHY just after setting up MDI-x polarity.
Fixes: 605f196efb ("phy: Add support for Marvell 88E1118 PHY")
Signed-off-by: Pavel Parkhomenko <Pavel.Parkhomenko@baikalelectronics.ru>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Cc: stable@vger.kernel.org
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe4f57bf7b upstream.
It is mandatory for a software to issue a reset upon modifying RGMII
Receive Timing Control and RGMII Transmit Timing Control bit fields of MAC
Specific Control register 2 (page 2, register 21) otherwise the changes
won't be perceived by the PHY (the same is applicable for a lot of other
registers). Not setting the RGMII delays on the platforms that imply it'
being done on the PHY side will consequently cause the traffic loss. We
discovered that the denoted soft-reset is missing in the
m88e1121_config_aneg() method for the case if the RGMII delays are
modified but the MDIx polarity isn't changed or the auto-negotiation is
left enabled, thus causing the traffic loss on our platform with Marvell
Alaska 88E1510 installed. Let's fix that by issuing the soft-reset if the
delays have been actually set in the m88e1121_config_aneg_rgmii_delays()
method.
Cc: stable@vger.kernel.org
Fixes: d6ab933647 ("net: phy: marvell: Avoid unnecessary soft reset")
Signed-off-by: Pavel Parkhomenko <Pavel.Parkhomenko@baikalelectronics.ru>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20220205203932.26899-1-Pavel.Parkhomenko@baikalelectronics.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c759040c1 upstream.
When receiving a CAN frame the current code logic does not consider
concurrently receiving processes which do not show up in real world
usage.
Ziyang Xuan writes:
The following syz problem is one of the scenarios. so->rx.len is
changed by isotp_rcv_ff() during isotp_rcv_cf(), so->rx.len equals
0 before alloc_skb() and equals 4096 after alloc_skb(). That will
trigger skb_over_panic() in skb_put().
=======================================================
CPU: 1 PID: 19 Comm: ksoftirqd/1 Not tainted 5.16.0-rc8-syzkaller #0
RIP: 0010:skb_panic+0x16c/0x16e net/core/skbuff.c:113
Call Trace:
<TASK>
skb_over_panic net/core/skbuff.c:118 [inline]
skb_put.cold+0x24/0x24 net/core/skbuff.c:1990
isotp_rcv_cf net/can/isotp.c:570 [inline]
isotp_rcv+0xa38/0x1e30 net/can/isotp.c:668
deliver net/can/af_can.c:574 [inline]
can_rcv_filter+0x445/0x8d0 net/can/af_can.c:635
can_receive+0x31d/0x580 net/can/af_can.c:665
can_rcv+0x120/0x1c0 net/can/af_can.c:696
__netif_receive_skb_one_core+0x114/0x180 net/core/dev.c:5465
__netif_receive_skb+0x24/0x1b0 net/core/dev.c:5579
Therefore we make sure the state changes and data structures stay
consistent at CAN frame reception time by adding a spin_lock in
isotp_rcv(). This fixes the issue reported by syzkaller but does not
affect real world operation.
Fixes: e057dd3fc2 ("can: add ISO 15765-2:2016 transport protocol")
Link: https://lore.kernel.org/linux-can/d7e69278-d741-c706-65e1-e87623d9a8e8@huawei.com/T/
Link: https://lore.kernel.org/all/20220208200026.13783-1-socketcan@hartkopp.net
Cc: stable@vger.kernel.org
Reported-by: syzbot+4c63f36709a642f801c5@syzkaller.appspotmail.com
Reported-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb8e52e490 upstream.
Commit c2426d2ad5 ("ima: added support for new kernel cmdline parameter
ima_template_fmt") introduced an additional check on the ima_template
variable to avoid multiple template selection.
Unfortunately, ima_template could be also set by the setup function of the
ima_hash= parameter, when it calls ima_template_desc_current(). This causes
attempts to choose a new template with ima_template= or with
ima_template_fmt=, after ima_hash=, to be ignored.
Achieve the goal of the commit mentioned with the new static variable
template_setup_done, so that template selection requests after ima_hash=
are not ignored.
Finally, call ima_init_template_list(), if not already done, to initialize
the list of templates before lookup_template_desc() is called.
Reported-by: Guo Zihua <guozihua@huawei.com>
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Cc: stable@vger.kernel.org
Fixes: c2426d2ad5 ("ima: added support for new kernel cmdline parameter ima_template_fmt")
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9aa422ad32 upstream.
The function tipc_mon_rcv() allows a node to receive and process
domain_record structs from peer nodes to track their views of the
network topology.
This patch verifies that the number of members in a received domain
record does not exceed the limit defined by MAX_MON_DOMAIN, something
that may otherwise lead to a stack overflow.
tipc_mon_rcv() is called from the function tipc_link_proto_rcv(), where
we are reading a 32 bit message data length field into a uint16. To
avert any risk of bit overflow, we add an extra sanity check for this in
that function. We cannot see that happen with the current code, but
future designers being unaware of this risk, may introduce it by
allowing delivery of very large (> 64k) sk buffers from the bearer
layer. This potential problem was identified by Eric Dumazet.
This fixes CVE-2022-0435
Reported-by: Samuel Page <samuel.page@appgate.com>
Reported-by: Eric Dumazet <edumazet@google.com>
Fixes: 35c55c9877 ("tipc: add neighbor monitoring framework")
Signed-off-by: Jon Maloy <jmaloy@redhat.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Samuel Page <samuel.page@appgate.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c6ce9c5831 upstream.
The soft dependency on cryptomgr is only needed in algapi because
if algapi isn't present then no algorithms can be loaded. This
also fixes the case where api is built-in but algapi is built as
a module as the soft dependency would otherwise get lost.
Fixes: 8ab23d547f ("crypto: api - Add softdep on cryptomgr")
Reported-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c212e1bae upstream.
Refuse SIDA memops on guests which are not protected.
For normal guests, the secure instruction data address designation,
which determines the location we access, is not under control of KVM.
Fixes: 19e1227768 (KVM: S390: protvirt: Introduce instruction data area bounce buffer)
Signed-off-by: Janis Schoetterl-Glausch <scgl@linux.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eda0cf1202 upstream.
Add a specific test for the reload issue fixed with
commit 23c54263ef ("netfilter: nft_set_pipapo: allocate pcpu scratch maps on clone").
Add to set, then flush set content + restore without other add/remove in
the transaction.
On kernels before the fix, this test case fails:
net,mac with reload [FAIL]
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2bdfd2825c upstream.
It was found that a "suspicious RCU usage" lockdep warning was issued
with the rcu_read_lock() call in update_sibling_cpumasks(). It is
because the update_cpumasks_hier() function may sleep. So we have
to release the RCU lock, call update_cpumasks_hier() and reacquire
it afterward.
Also add a percpu_rwsem_assert_held() in update_sibling_cpumasks()
instead of stating that in the comment.
Fixes: 4716909cc5 ("cpuset: Track cpusets that use parent's effective_cpus")
Signed-off-by: Waiman Long <longman@redhat.com>
Tested-by: Phil Auld <pauld@redhat.com>
Reviewed-by: Phil Auld <pauld@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 897026aaa7 upstream.
While running "./check -I 200 generic/475" it sometimes gives below
kernel BUG(). Ideally we should not call ext4_write_inline_data() if
ext4_create_inline_data() has failed.
<log snip>
[73131.453234] kernel BUG at fs/ext4/inline.c:223!
<code snip>
212 static void ext4_write_inline_data(struct inode *inode, struct ext4_iloc *iloc,
213 void *buffer, loff_t pos, unsigned int len)
214 {
<...>
223 BUG_ON(!EXT4_I(inode)->i_inline_off);
224 BUG_ON(pos + len > EXT4_I(inode)->i_inline_size);
This patch handles the error and prints out a emergency msg saying potential
data loss for the given inode (since we couldn't restore the original
inline_data due to some previous error).
[ 9571.070313] EXT4-fs (dm-0): error restoring inline_data for inode -- potential data loss! (inode 1703982, error -30)
Reported-by: Eric Whitney <enwlinux@gmail.com>
Signed-off-by: Ritesh Harjani <riteshh@linux.ibm.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/9f4cd7dfd54fa58ff27270881823d94ddf78dd07.1642416995.git.riteshh@linux.ibm.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dfd0dfb9a7 upstream.
The driver overrides error codes returned by platform_get_irq_optional()
to -EINVAL for some strange reason, so if it returns -EPROBE_DEFER, the
driver will fail the probe permanently instead of the deferred probing.
Switch to propagating the proper error codes to platform driver code
upwards.
[ bp: Massage commit message. ]
Fixes: 0d4429301c ("EDAC: Add APM X-Gene SoC EDAC driver")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220124185503.6720-3-s.shtylyov@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 279eb8575f upstream.
The driver overrides the error codes returned by platform_get_irq() to
-ENODEV for some strange reason, so if it returns -EPROBE_DEFER, the
driver will fail the probe permanently instead of the deferred probing.
Switch to propagating the proper error codes to platform driver code
upwards.
[ bp: Massage commit message. ]
Fixes: 71bcada88b ("edac: altera: Add Altera SDRAM EDAC support")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220124185503.6720-2-s.shtylyov@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d9093457b upstream.
Add a check for !buf->single before calling pt_buffer_region_size in a
place where a missing check can cause a kernel crash.
Fixes a bug introduced by commit 670638477a ("perf/x86/intel/pt:
Opportunistically use single range output mode"), which added a
support for PT single-range output mode. Since that commit if a PT
stop filter range is hit while tracing, the kernel will crash because
of a null pointer dereference in pt_handle_status due to calling
pt_buffer_region_size without a ToPA configured.
The commit which introduced single-range mode guarded almost all uses of
the ToPA buffer variables with checks of the buf->single variable, but
missed the case where tracing was stopped by the PT hardware, which
happens when execution hits a configured stop filter.
Tested that hitting a stop filter while PT recording successfully
records a trace with this patch but crashes without this patch.
Fixes: 670638477a ("perf/x86/intel/pt: Opportunistically use single range output mode")
Signed-off-by: Tristan Hume <tristan@thume.ca>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@kernel.org
Link: https://lkml.kernel.org/r/20220127220806.73664-1-tristan@thume.ca
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a3f781a9d6 upstream.
Add a config option CONFIG_FRAMEBUFFER_CONSOLE_LEGACY_ACCELERATION to
enable bitblt and fillrect hardware acceleration in the framebuffer
console. If disabled, such acceleration will not be used, even if it is
supported by the graphics hardware driver.
If you plan to use DRM as your main graphics output system, you should
disable this option since it will prevent compiling in code which isn't
used later on when DRM takes over.
For all other configurations, e.g. if none of your graphic cards support
DRM (yet), DRM isn't available for your architecture, or you can't be
sure that the graphic card in the target system will support DRM, you
most likely want to enable this option.
In the non-accelerated case (e.g. when DRM is used), the inlined
fb_scrollmode() function is hardcoded to return SCROLL_REDRAW and as such the
compiler is able to optimize much unneccesary code away.
In this v3 patch version I additionally changed the GETVYRES() and GETVXRES()
macros to take a pointer to the fbcon_display struct. This fixes the build when
console rotation is enabled and helps the compiler again to optimize out code.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v5.10+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220202135531.92183-4-deller@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87ab9f6b74 upstream.
This reverts commit 39aead8373.
Revert the first (of 2) commits which disabled scrolling acceleration in
fbcon/fbdev. It introduced a regression for fbdev-supported graphic cards
because of the performance penalty by doing screen scrolling by software
instead of using the existing graphic card 2D hardware acceleration.
Console scrolling acceleration was disabled by dropping code which
checked at runtime the driver hardware capabilities for the
BINFO_HWACCEL_COPYAREA or FBINFO_HWACCEL_FILLRECT flags and if set, it
enabled scrollmode SCROLL_MOVE which uses hardware acceleration to move
screen contents. After dropping those checks scrollmode was hard-wired
to SCROLL_REDRAW instead, which forces all graphic cards to redraw every
character at the new screen position when scrolling.
This change effectively disabled all hardware-based scrolling acceleration for
ALL drivers, because now all kind of 2D hardware acceleration (bitblt,
fillrect) in the drivers isn't used any longer.
The original commit message mentions that only 3 DRM drivers (nouveau, omapdrm
and gma500) used hardware acceleration in the past and thus code for checking
and using scrolling acceleration is obsolete.
This statement is NOT TRUE, because beside the DRM drivers there are around 35
other fbdev drivers which depend on fbdev/fbcon and still provide hardware
acceleration for fbdev/fbcon.
The original commit message also states that syzbot found lots of bugs in fbcon
and thus it's "often the solution to just delete code and remove features".
This is true, and the bugs - which actually affected all users of fbcon,
including DRM - were fixed, or code was dropped like e.g. the support for
software scrollback in vgacon (commit 973c096f6a).
So to further analyze which bugs were found by syzbot, I've looked through all
patches in drivers/video which were tagged with syzbot or syzkaller back to
year 2005. The vast majority fixed the reported issues on a higher level, e.g.
when screen is to be resized, or when font size is to be changed. The few ones
which touched driver code fixed a real driver bug, e.g. by adding a check.
But NONE of those patches touched code of either the SCROLL_MOVE or the
SCROLL_REDRAW case.
That means, there was no real reason why SCROLL_MOVE had to be ripped-out and
just SCROLL_REDRAW had to be used instead. The only reason I can imagine so far
was that SCROLL_MOVE wasn't used by DRM and as such it was assumed that it
could go away. That argument completely missed the fact that SCROLL_MOVE is
still heavily used by fbdev (non-DRM) drivers.
Some people mention that using memcpy() instead of the hardware acceleration is
pretty much the same speed. But that's not true, at least not for older graphic
cards and machines where we see speed decreases by factor 10 and more and thus
this change leads to console responsiveness way worse than before.
That's why the original commit is to be reverted. By reverting we
reintroduce hardware-based scrolling acceleration and fix the
performance regression for fbdev drivers.
There isn't any impact on DRM when reverting those patches.
Signed-off-by: Helge Deller <deller@gmx.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Sven Schnelle <svens@stackframe.org>
Cc: stable@vger.kernel.org # v5.10+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220202135531.92183-3-deller@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f3bdbc3f1 upstream.
When building with 'make -s', there is some output from resolve_btfids:
$ make -sj"$(nproc)" oldconfig prepare
MKDIR .../tools/bpf/resolve_btfids/libbpf/
MKDIR .../tools/bpf/resolve_btfids//libsubcmd
LINK resolve_btfids
Silent mode means that no information should be emitted about what is
currently being done. Use the $(silent) variable from Makefile.include
to avoid defining the msg macro so that there is no information printed.
Fixes: fbbb68de80 ("bpf: Add resolve_btfids tool to resolve BTF IDs in ELF object")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20220201212503.731732-1-nathan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b9199181a9 upstream.
Recursive make commands should always use the variable MAKE, not the
explicit command name ‘make’. This has benefits and removes the
following warning when multiple jobs are used for the build:
make[2]: warning: jobserver unavailable: using -j1. Add '+' to parent make rule.
Fixes: a8ba798bc8 ("selftests: enable O and KBUILD_OUTPUT")
Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Reviewed-by: André Almeida <andrealmeid@collabora.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 908a26e139 upstream.
pipe named FIFO special file is being created in execveat.c to perform
some tests. Makefile doesn't need to do anything with the pipe. When it
isn't found, Makefile generates the following build error:
make: *** No rule to make target
'../tools/testing/selftests/exec/pipe', needed by 'all'. Stop.
pipe is created and removed during test run-time.
Amended change log to add pipe remove info:
Shuah Khan <skhan@linuxfoundation.org>
Fixes: 61016db15b ("selftests/exec: Verify execve of non-regular files fail")
Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b293dcc473 upstream.
After commit 2fd3fb0be1d1 ("kasan, vmalloc: unpoison VM_ALLOC pages
after mapping"), non-VM_ALLOC mappings will be marked as accessible
in __get_vm_area_node() when KASAN is enabled. But now the flag for
ringbuf area is VM_ALLOC, so KASAN will complain out-of-bound access
after vmap() returns. Because the ringbuf area is created by mapping
allocated pages, so use VM_MAP instead.
After the change, info in /proc/vmallocinfo also changes from
[start]-[end] 24576 ringbuf_map_alloc+0x171/0x290 vmalloc user
to
[start]-[end] 24576 ringbuf_map_alloc+0x171/0x290 vmap user
Fixes: 457f44363a ("bpf: Implement BPF ring buffer and verifier support for it")
Reported-by: syzbot+5ad567a418794b9b5983@syzkaller.appspotmail.com
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20220202060158.6260-1-houtao1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f84a9450d upstream.
The 'tail' and 'head' are 'unsigned int' type free-running count, when
'head' is overflow, the 'int i (= tail) < u32 head' will be false:
Only '- loop 0: idx = 63' result is shown, so it needs to use 'int' type
to compare, it can handle the overflow correctly.
typedef uint32_t u32;
int main()
{
u32 tail, head;
int stail, shead;
int i, loop;
tail = 0xffffffff;
head = 0x00000000;
for (i = tail, loop = 0; i < head; i++) {
unsigned int idx = i & 63;
printf("+ loop %d: idx = %u\n", loop++, idx);
}
stail = tail;
shead = head;
for (i = stail, loop = 0; i < shead; i++) {
unsigned int idx = i & 63;
printf("- loop %d: idx = %u\n", loop++, idx);
}
return 0;
}
Fixes: 5cdad90de6 ("gve: Batch AQ commands for creating and destroying queues.")
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab451ea952 upstream.
From RFC 7530 Section 16.34.5:
o The server has not recorded an unconfirmed { v, x, c, *, * } and
has recorded a confirmed { v, x, c, *, s }. If the principals of
the record and of SETCLIENTID_CONFIRM do not match, the server
returns NFS4ERR_CLID_INUSE without removing any relevant leased
client state, and without changing recorded callback and
callback_ident values for client { x }.
The current code intends to do what the spec describes above but
it forgot to set 'old' to NULL resulting to the confirmed client
to be expired.
Fixes: 2b63482185 ("nfsd: fix clid_inuse on mount with security change")
Signed-off-by: Dai Ngo <dai.ngo@oracle.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Bruce Fields <bfields@fieldses.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e986f0e602 upstream.
ASUS Chromebook C223 with Celeron N3350 crashes sometimes during
cold booot. Inspection of the kernel log showed that it gets into
an inifite loop logging the following message:
->handle_irq(): 000000009cdb51e8, handle_bad_irq+0x0/0x251
->irq_data.chip(): 000000005ec212a7, 0xffffa043009d8e7
->action(): 00000
IRQ_NOPROBE set
unexpected IRQ trap at vector 7c
The issue happens during cold boot but only if cold boot happens
at most several dozen seconds after Chromebook is powered off. For
longer intervals between power off and power on (cold boot) the issue
does not reproduce. The unexpected interrupt is sourced from INT3452
GPIO pin which is used for SD card detect. Investigation relevealed
that when the interval between power off and power on (cold boot)
is less than several dozen seconds then values of INT3452 GPIO interrupt
enable and interrupt pending registers survive power off and power
on sequence and interrupt for SD card detect pin is enabled and pending
during probe of SD controller which causes the unexpected IRQ message.
"Intel Pentium and Celeron Processor N- and J- Series" volume 3 doc
mentions that GPIO interrupt enable and status registers default
value is 0x0.
The fix clears INT3452 GPIO interrupt enabled and interrupt pending
registers in its probe function.
Fixes: 7981c0015a ("pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support")
Signed-off-by: Łukasz Bartosik <lb@semihalf.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e12963c453 upstream.
The commit af7e3eeb84 ("pinctrl: intel: Disable input and output buffer
when switching to GPIO") hadn't taken into account an update of the IRQ
flags scenario.
When updating the IRQ flags on the preconfigured line the ->irq_set_type()
is called again. In such case the sequential Rx buffer configuration
changes may trigger a falling or rising edge interrupt that may lead,
on some platforms, to an undesired event.
This may happen because each of intel_gpio_set_gpio_mode() and
__intel_gpio_set_direction() updates the pad configuration with a different
value of the GPIORXDIS bit. Notable, that the intel_gpio_set_gpio_mode() is
called only for the pads that are configured as an input. Due to this fact,
integrate the logic of __intel_gpio_set_direction() call into the
intel_gpio_set_gpio_mode() so that the Rx buffer won't be disabled and
immediately re-enabled.
Fixes: af7e3eeb84 ("pinctrl: intel: Disable input and output buffer when switching to GPIO")
Reported-by: Kane Chen <kane.chen@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Grace Kao <grace.kao@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7a6021aaf upstream.
If the device does not exist, of_get_child_by_name() will return NULL
pointer.
And devm_snd_soc_register_component() does not check it.
Also, I have noticed that cpcap_codec_driver has not been used yet.
Therefore, it should be better to check it in order to avoid the future
dereference of the NULL pointer.
Fixes: f6cdf2d344 ("ASoC: cpcap: new codec")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20220111025048.524134-1-jiasheng@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e958b58847 upstream.
This patch is based on one in the Xilinx kernel tree, "ASoc: xlnx: Make
buffer bytes multiple of period bytes" by Devarsh Thakkar. The same
issue exists in the mainline version of the driver. The original
patch description is as follows:
"The Xilinx Audio Formatter IP has a constraint on period
bytes to be multiple of 64. This leads to driver changing
the period size to suitable frames such that period bytes
are multiple of 64.
Now since period bytes and period size are updated but not
the buffer bytes, this may make the buffer bytes unaligned
and not multiple of period bytes.
When this happens we hear popping noise as while DMA is being
done the buffer bytes are not enough to complete DMA access
for last period of frame within the application buffer boundary.
To avoid this, align buffer bytes too as multiple of 64, and
set another constraint to always enforce number of periods as
integer. Now since, there is already a rule in alsa core
to enforce Buffer size = Number of Periods * Period Size
this automatically aligns buffer bytes as multiple of period
bytes."
Fixes: 6f6c3c36f0 ("ASoC: xlnx: add pcm formatter platform driver")
Cc: Devarsh Thakkar <devarsh.thakkar@xilinx.com>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220107214711.1100162-2-robert.hancock@calian.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90a3d22ff0 upstream.
Smatch detected a divide by zero bug in check_overlay_scaling().
drivers/gpu/drm/i915/display/intel_overlay.c:976 check_overlay_scaling()
error: potential divide by zero bug '/ rec->dst_height'.
drivers/gpu/drm/i915/display/intel_overlay.c:980 check_overlay_scaling()
error: potential divide by zero bug '/ rec->dst_width'.
Prevent this by ensuring that the dst height and width are non-zero.
Fixes: 02e792fbaa ("drm/i915: implement drmmode overlay support v4")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220124122409.GA31673@kili
(cherry picked from commit cf5b64f7f1)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7af037c39b upstream.
Unlike gmac100, gmac1000, gmac4 has 27 DMA registers and they are
located at DMA_CHAN_BASE_ADDR (0x1100). In order for ethtool to dump
gmac4 DMA registers correctly, this commit checks if a net_device has
gmac4 and uses different logic to dump its DMA registers.
This fixes the following KASAN warning, which can normally be triggered
by a command similar like "ethtool -d eth0":
BUG: KASAN: vmalloc-out-of-bounds in dwmac4_dump_dma_regs+0x6d4/0xb30
Write of size 4 at addr ffffffc010177100 by task ethtool/1839
kasan_report+0x200/0x21c
__asan_report_store4_noabort+0x34/0x60
dwmac4_dump_dma_regs+0x6d4/0xb30
stmmac_ethtool_gregs+0x110/0x204
ethtool_get_regs+0x200/0x4b0
dev_ethtool+0x1dac/0x3800
dev_ioctl+0x7c0/0xb50
sock_ioctl+0x298/0x6c4
...
Fixes: fbf68229ff ("net: stmmac: unify registers dumps methods")
Signed-off-by: Camel Guo <camelg@axis.com>
Link: https://lore.kernel.org/r/20220131083841.3346801-1-camel.guo@axis.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0cfa548db upstream.
When setting Tx sci explicit, the Rx side is expected to use this
sci and not recalculate it from the packet.However, in case of Tx sci
is explicit and send_sci is off, the receiver is wrongly recalculate
the sci from the source MAC address which most likely be different
than the explicit sci.
Fix by preventing such configuration when macsec newlink is established
and return EINVAL error code on such cases.
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Lior Nahmanson <liorna@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Raed Salem <raeds@nvidia.com>
Link: https://lore.kernel.org/r/1643542672-29403-1-git-send-email-raeds@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9cef24c8b7 upstream.
Current macsec netdev notify handler handles NETDEV_UNREGISTER event by
releasing relevant SW resources only, this causes resources leak in case
of macsec HW offload, as the underlay driver was not notified to clean
it's macsec offload resources.
Fix by calling the underlay driver to clean it's relevant resources
by moving offload handling from macsec_dellink() to macsec_common_dellink()
when handling NETDEV_UNREGISTER event.
Fixes: 3cf3227a21 ("net: macsec: hardware offloading infrastructure")
Signed-off-by: Lior Nahmanson <liorna@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/1643542141-28956-1-git-send-email-raeds@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1293fccc9e upstream.
Drivers are expected to set the PHY current_channel and current_page
according to their default state. The hwsim driver is advertising being
configured on channel 13 by default but that is not reflected in its own
internal pib structure. In order to ensure that this driver consider the
current channel as being 13 internally, we at least need to set the
pib->channel field to 13.
Fixes: f25da51fdc ("ieee802154: hwsim: add replacement for fakelb")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[stefan@datenfreihafen.org: fixed assigment from page to channel]
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20220125121426.848337-2-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2cbd27267f upstream.
Apply only valid chip select value. This change fixes case where chip
select is set to initial value of '-1' during probe and PM supend and
subsequent resume can try to use the value with undefined behaviour.
Also in case where gpio based chip select, the check in
bcm_qspi_chip_select() shall prevent undefined behaviour on resume.
Fixes: fa236a7ef2 ("spi: bcm-qspi: Add Broadcom MSPI driver")
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220127185359.27322-1-kdasu.kdev@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b45a7738e upstream.
The polling loop for the register change in iommu_ga_log_enable() needs
to have a udelay() in it. Otherwise the CPU might be faster than the
IOMMU hardware and wrongly trigger the WARN_ON() further down the code
stream. Use a 10us for udelay(), has there is some hardware where
activation of the GA log can take more than a 100ms.
A future optimization should move the activation check of the GA log
to the point where it gets used for the first time. But that is a
bigger change and not suitable for a fix.
Fixes: 8bda0cfbdc ("iommu/amd: Detect and initialize guest vAPIC log")
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20220204115537.3894-1-joro@8bytes.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 36e8169ec9 upstream.
Partially revert the commit mentioned in the Fixes line to make sure that
allocation and erasing multicast struct are locked.
BUG: KASAN: use-after-free in ucma_cleanup_multicast drivers/infiniband/core/ucma.c:491 [inline]
BUG: KASAN: use-after-free in ucma_destroy_private_ctx+0x914/0xb70 drivers/infiniband/core/ucma.c:579
Read of size 8 at addr ffff88801bb74b00 by task syz-executor.1/25529
CPU: 0 PID: 25529 Comm: syz-executor.1 Not tainted 5.16.0-rc7-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_address_description.constprop.0.cold+0x8d/0x320 mm/kasan/report.c:247
__kasan_report mm/kasan/report.c:433 [inline]
kasan_report.cold+0x83/0xdf mm/kasan/report.c:450
ucma_cleanup_multicast drivers/infiniband/core/ucma.c:491 [inline]
ucma_destroy_private_ctx+0x914/0xb70 drivers/infiniband/core/ucma.c:579
ucma_destroy_id+0x1e6/0x280 drivers/infiniband/core/ucma.c:614
ucma_write+0x25c/0x350 drivers/infiniband/core/ucma.c:1732
vfs_write+0x28e/0xae0 fs/read_write.c:588
ksys_write+0x1ee/0x250 fs/read_write.c:643
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
Currently the xarray search can touch a concurrently freeing mc as the
xa_for_each() is not surrounded by any lock. Rather than hold the lock for
a full scan hold it only for the effected items, which is usually an empty
list.
Fixes: 95fe51096b ("RDMA/ucma: Remove mc_list and rely on xarray")
Link: https://lore.kernel.org/r/1cda5fabb1081e8d16e39a48d3a4f8160cea88b8.1642491047.git.leonro@nvidia.com
Reported-by: syzbot+e3f96c43d19782dd14a7@syzkaller.appspotmail.com
Suggested-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb902cb47c upstream.
This patch adds accounting flags to fs_context and legacy_fs_context
allocation sites so that kernel could correctly charge these objects.
We have written a PoC to demonstrate the effect of the missing-charging
bugs. The PoC takes around 1,200MB unaccounted memory, while it is
charged for only 362MB memory usage. We evaluate the PoC on QEMU x86_64
v5.2.90 + Linux kernel v5.10.19 + Debian buster. All the limitations
including ulimits and sysctl variables are set as default. Specifically,
the hard NOFILE limit and nr_open in sysctl are both 1,048,576.
/*------------------------- POC code ----------------------------*/
#define _GNU_SOURCE
#include <sys/types.h>
#include <sys/file.h>
#include <time.h>
#include <sys/wait.h>
#include <stdint.h>
#include <stdlib.h>
#include <unistd.h>
#include <stdio.h>
#include <signal.h>
#include <sched.h>
#include <fcntl.h>
#include <linux/mount.h>
#define errExit(msg) do { perror(msg); exit(EXIT_FAILURE); \
} while (0)
#define STACK_SIZE (8 * 1024)
#ifndef __NR_fsopen
#define __NR_fsopen 430
#endif
static inline int fsopen(const char *fs_name, unsigned int flags)
{
return syscall(__NR_fsopen, fs_name, flags);
}
static char thread_stack[512][STACK_SIZE];
int thread_fn(void* arg)
{
for (int i = 0; i< 800000; ++i) {
int fsfd = fsopen("nfs", FSOPEN_CLOEXEC);
if (fsfd == -1) {
errExit("fsopen");
}
}
while(1);
return 0;
}
int main(int argc, char *argv[]) {
int thread_pid;
for (int i = 0; i < 1; ++i) {
thread_pid = clone(thread_fn, thread_stack[i] + STACK_SIZE, \
SIGCHLD, NULL);
}
while(1);
return 0;
}
/*-------------------------- end --------------------------------*/
Link: https://lkml.kernel.org/r/1626517201-24086-1-git-send-email-nglaive@gmail.com
Signed-off-by: Yutian Yang <nglaive@gmail.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: <shenwenbo@zju.edu.cn>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit d491a2c2cf which is
commit 9de2b9286a upstream
With this patch in the tree, Chromebooks running the affected hardware
no longer boot. Bisect points to this patch, and reverting it fixes
the problem.
An analysis of the code with this patch applied shows:
ret = init_clks(pdev, clk);
if (ret)
return ERR_PTR(ret);
...
for (j = 0; j < MAX_CLKS && data->clk_id[j]; j++) {
struct clk *c = clk[data->clk_id[j]];
if (IS_ERR(c)) {
dev_err(&pdev->dev, "%s: clk unavailable\n",
data->name);
return ERR_CAST(c);
}
scpd->clk[j] = c;
}
Not all clocks in the clk_names array have to be present. Only the clocks
in the data->clk_id array are actually needed. The code already checks if
the required clocks are available and bails out if not. The assumption that
all clocks have to be present is wrong, and commit 9de2b9286a needs to be
reverted.
Fixes: 9de2b9286a ("ASoC: mediatek: Check for error clk pointer")
Cc: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Cc: Mark Brown <broonie@kernel.org>
Cc: James Liao <jamesjj.liao@mediatek.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com
Cc: Frank Wunderlich <frank-w@public-files.de>
Cc: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/lkml/20220205014755.699603-1-linux@roeck-us.net/
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c10a0f877f upstream.
When using devm_request_free_mem_region() and devm_memremap_pages() to
add ZONE_DEVICE memory, if requested free mem region's end pfn were
huge(e.g., 0x400000000), the node_end_pfn() will be also huge (see
move_pfn_range_to_zone()). Thus it creates a huge hole between
node_start_pfn() and node_end_pfn().
We found on some AMD APUs, amdkfd requested such a free mem region and
created a huge hole. In such a case, following code snippet was just
doing busy test_bit() looping on the huge hole.
for (pfn = start_pfn; pfn < end_pfn; pfn++) {
struct page *page = pfn_to_online_page(pfn);
if (!page)
continue;
...
}
So we got a soft lockup:
watchdog: BUG: soft lockup - CPU#6 stuck for 26s! [bash:1221]
CPU: 6 PID: 1221 Comm: bash Not tainted 5.15.0-custom #1
RIP: 0010:pfn_to_online_page+0x5/0xd0
Call Trace:
? kmemleak_scan+0x16a/0x440
kmemleak_write+0x306/0x3a0
? common_file_perm+0x72/0x170
full_proxy_write+0x5c/0x90
vfs_write+0xb9/0x260
ksys_write+0x67/0xe0
__x64_sys_write+0x1a/0x20
do_syscall_64+0x3b/0xc0
entry_SYSCALL_64_after_hwframe+0x44/0xae
I did some tests with the patch.
(1) amdgpu module unloaded
before the patch:
real 0m0.976s
user 0m0.000s
sys 0m0.968s
after the patch:
real 0m0.981s
user 0m0.000s
sys 0m0.973s
(2) amdgpu module loaded
before the patch:
real 0m35.365s
user 0m0.000s
sys 0m35.354s
after the patch:
real 0m1.049s
user 0m0.000s
sys 0m1.042s
Link: https://lkml.kernel.org/r/20211108140029.721144-1-lang.yu@amd.com
Signed-off-by: Lang Yu <lang.yu@amd.com>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6a51abdeb2 upstream.
Controller deletion/reset, immediately followed by or concurrent with
a reconnect, is hard failing the connect attempt resulting in a
complete loss of connectivity to the controller.
In the connect request, fabrics looks for an existing controller with
the same address components and aborts the connect if a controller
already exists and the duplicate connect option isn't set. The match
routine filters out controllers that are dead or dying, so they don't
interfere with the new connect request.
When NVME_CTRL_DELETING_NOIO was added, it missed updating the state
filters in the nvmf_ctlr_matches_baseopts() routine. Thus, when in this
new state, it's seen as a live controller and fails the connect request.
Correct by adding the DELETING_NIO state to the match checks.
Fixes: ecca390e80 ("nvme: fix deadlock in disconnect during scan_work and/or ana_work")
Cc: <stable@vger.kernel.org> # v5.7+
Signed-off-by: Uday Shankar <ushankar@purestorage.com>
Reviewed-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 30fbce3747 upstream.
The eDP link rate reported by the DP_MAX_LINK_RATE dpcd register (0xa) is
contradictory to the highest rate supported reported by
EDID (0xc = LINK_RATE_RBR2). The effects of this compounded with commit
'4a8ca46bae8a ("drm/amd/display: Default max bpc to 16 for eDP")' results
in no display modes being found and a dark panel.
For now, simply force the maximum supported link rate for the eDP attached
2018 15" Apple Retina panels.
Additionally, we must also check the firmware revision since the device ID
reported by the DPCD is identical to that of the more capable 16,1,
incorrectly quirking it. We also use said firmware check to quirk the
refreshed 15,1 models with Vega graphics as they use a slightly newer
firmware version.
Tested-by: Aun-Ali Zaidi <admin@kodeit.net>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Aun-Ali Zaidi <admin@kodeit.net>
Signed-off-by: Aditya Garg <gargaditya08@live.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b777d4d9e upstream.
Bounds checking when parsing init scripts embedded in the BIOS reject
access to the last byte. This causes driver initialization to fail on
Apple eMac's with GeForce 2 MX GPUs, leaving the system with no working
console.
This is probably only seen on OpenFirmware machines like PowerPC Macs
because the BIOS image provided by OF is only the used parts of the ROM,
not a power-of-two blocks read from PCI directly so PCs always have
empty bytes at the end that are never accessed.
Signed-off-by: Nick Lopez <github@glowingmonkey.org>
Fixes: 4d4e9907ff ("drm/nouveau/bios: guard against out-of-bounds accesses to image")
Cc: <stable@vger.kernel.org> # v4.10+
Reviewed-by: Ilia Mirkin <imirkin@alum.mit.edu>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220122081906.2633061-1-github@glowingmonkey.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 41a8601302 upstream.
Newer versions of the X570 Master come with a newer revision of the
mainboard chipset - the X570S. These boards have the same ALC1220 codec
but seem to initialize the codec with a different parameter in Coef 0x7
which causes the output audio to be very low. We therefore write a
known-good value to Coef 0x7 to fix that. As the value is the exact same
as on the other X570(non-S) boards the same quirk-function can be shared
between both generations.
This commit adds the Gigabyte X570S Aorus Master to the list of boards
using the ALC1220_FIXUP_GB_X570 quirk. This fixes both, the silent output
and the no-audio after reboot from windows problems.
This work has been tested by the folks over at the level1techs forum here:
https://forum.level1techs.com/t/has-anybody-gotten-audio-working-in-linux-on-aorus-x570-master/154072
Signed-off-by: Christian Lachner <gladiac@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220129113243.93068-3-gladiac@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 549f8ffc7b upstream.
The LED class devices that are created by HD-audio codec drivers are
registered via devm_led_classdev_register() and associated with the
HD-audio codec device. Unfortunately, it turned out that the devres
release doesn't work for this case; namely, since the codec resource
release happens before the devm call chain, it triggers a NULL
dereference or a UAF for a stale set_brightness_delay callback.
For fixing the bug, this patch changes the LED class device register
and unregister in a manual manner without devres, keeping the
instances in hda_gen_spec.
Reported-by: Alexander Sergeyev <sergeev917@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220111195229.a77wrpjclqwrx4bx@localhost.localdomain
Link: https://lore.kernel.org/r/20220126145011.16728-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f26d043313 upstream.
When an admin enables audit at early boot via the "audit=1" kernel
command line the audit queue behavior is slightly different; the
audit subsystem goes to greater lengths to avoid dropping records,
which unfortunately can result in problems when the audit daemon is
forcibly stopped for an extended period of time.
This patch makes a number of changes designed to improve the audit
queuing behavior so that leaving the audit daemon in a stopped state
for an extended period does not cause a significant impact to the
system.
- kauditd_send_queue() is now limited to looping through the
passed queue only once per call. This not only prevents the
function from looping indefinitely when records are returned
to the current queue, it also allows any recovery handling in
kauditd_thread() to take place when kauditd_send_queue()
returns.
- Transient netlink send errors seen as -EAGAIN now cause the
record to be returned to the retry queue instead of going to
the hold queue. The intention of the hold queue is to store,
perhaps for an extended period of time, the events which led
up to the audit daemon going offline. The retry queue remains
a temporary queue intended to protect against transient issues
between the kernel and the audit daemon.
- The retry queue is now limited by the audit_backlog_limit
setting, the same as the other queues. This allows admins
to bound the size of all of the audit queues on the system.
- kauditd_rehold_skb() now returns records to the end of the
hold queue to ensure ordering is preserved in the face of
recent changes to kauditd_send_queue().
Cc: stable@vger.kernel.org
Fixes: 5b52330bbf ("audit: fix auditd/kernel connection state tracking")
Fixes: f4b3ee3c85 ("audit: improve robustness of the audit queue handling")
Reported-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Tested-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Reviewed-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 186edf7e36 upstream.
On error path from cond_read_list() and duplicate_policydb_cond_list()
the cond_list_destroy() gets called a second time in caller functions,
resulting in NULL pointer deref. Fix this by resetting the
cond_list_len to 0 in cond_list_destroy(), making subsequent calls a
noop.
Also consistently reset the cond_list pointer to NULL after freeing.
Cc: stable@vger.kernel.org
Signed-off-by: Vratislav Bendel <vbendel@redhat.com>
[PM: fix line lengths in the description]
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b67985be40 upstream.
tcp_shift_skb_data() might collapse three packets into a larger one.
P_A, P_B, P_C -> P_ABC
Historically, it used a single tcp_skb_can_collapse_to(P_A) call,
because it was enough.
In commit 8571248411 ("tcp: coalesce/collapse must respect MPTCP extensions"),
this call was replaced by a call to tcp_skb_can_collapse(P_A, P_B)
But the now needed test over P_C has been missed.
This probably broke MPTCP.
Then later, commit 9b65b17db7 ("net: avoid double accounting for pure zerocopy skbs")
added an extra condition to tcp_skb_can_collapse(), but the missing call
from tcp_shift_skb_data() is also breaking TCP zerocopy, because P_A and P_C
might have different skb_zcopy_pure() status.
Fixes: 8571248411 ("tcp: coalesce/collapse must respect MPTCP extensions")
Fixes: 9b65b17db7 ("net: avoid double accounting for pure zerocopy skbs")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Mat Martineau <mathew.j.martineau@linux.intel.com>
Cc: Talal Ahmad <talalahmad@google.com>
Cc: Arjun Roy <arjunroy@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20220201184640.756716-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e42e70ad6a upstream.
When packet_setsockopt( PACKET_FANOUT_DATA ) reads po->fanout,
no lock is held, meaning that another thread can change po->fanout.
Given that po->fanout can only be set once during the socket lifetime
(it is only cleared from fanout_release()), we can use
READ_ONCE()/WRITE_ONCE() to document the race.
BUG: KCSAN: data-race in packet_setsockopt / packet_setsockopt
write to 0xffff88813ae8e300 of 8 bytes by task 14653 on cpu 0:
fanout_add net/packet/af_packet.c:1791 [inline]
packet_setsockopt+0x22fe/0x24a0 net/packet/af_packet.c:3931
__sys_setsockopt+0x209/0x2a0 net/socket.c:2180
__do_sys_setsockopt net/socket.c:2191 [inline]
__se_sys_setsockopt net/socket.c:2188 [inline]
__x64_sys_setsockopt+0x62/0x70 net/socket.c:2188
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffff88813ae8e300 of 8 bytes by task 14654 on cpu 1:
packet_setsockopt+0x691/0x24a0 net/packet/af_packet.c:3935
__sys_setsockopt+0x209/0x2a0 net/socket.c:2180
__do_sys_setsockopt net/socket.c:2191 [inline]
__se_sys_setsockopt net/socket.c:2188 [inline]
__x64_sys_setsockopt+0x62/0x70 net/socket.c:2188
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0x0000000000000000 -> 0xffff888106f8c000
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 14654 Comm: syz-executor.3 Not tainted 5.16.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 47dceb8ecd ("packet: add classic BPF fanout mode")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Link: https://lore.kernel.org/r/20220201022358.330621-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c80d401c52 upstream.
subparts_cpus should be limited as a subset of cpus_allowed, but it is
updated wrongly by using cpumask_andnot(). Use cpumask_and() instead to
fix it.
Fixes: ee8dde0cd2 ("cpuset: Add new v2 cpuset.sched.partition flag")
Signed-off-by: Tianchen Ding <dtcccc@linux.alibaba.com>
Reviewed-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee12595147 upstream.
This code calls fd_install() which gives the userspace access to the fd.
Then if copy_info_records_to_user() fails it calls put_unused_fd(fd) but
that will not release it and leads to a stale entry in the file
descriptor table.
Generally you can't trust the fd after a call to fd_install(). The fix
is to delay the fd_install() until everything else has succeeded.
Fortunately it requires CAP_SYS_ADMIN to reach this code so the security
impact is less.
Fixes: f644bc449b ("fanotify: fix copy_event_to_user() fid error clean up")
Link: https://lore.kernel.org/r/20220128195656.GA26981@kili
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Mathias Krause <minipli@grsecurity.net>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d8e5883d69 upstream.
The variable modact is not initialized before used in command
modify header allocation which can cause command to fail.
Fix by initializing modact with zeros.
Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: 8f1e0b97cc ("net/mlx5: E-Switch, Mark miss packets with new chain id mapping")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c5193a87b upstream.
Substitute del_timer() with del_timer_sync() in fw reset polling
deactivation flow, in order to prevent a race condition which occurs
when del_timer() is called and timer is deactivated while another
process is handling the timer interrupt. A situation that led to
the following call trace:
RIP: 0010:run_timer_softirq+0x137/0x420
<IRQ>
recalibrate_cpu_khz+0x10/0x10
ktime_get+0x3e/0xa0
? sched_clock_cpu+0xb/0xc0
__do_softirq+0xf5/0x2ea
irq_exit_rcu+0xc1/0xf0
sysvec_apic_timer_interrupt+0x9e/0xc0
asm_sysvec_apic_timer_interrupt+0x12/0x20
</IRQ>
Fixes: 38b9f903f2 ("net/mlx5: Handle sync reset request event")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 24f6008564 upstream.
The cgroup release_agent is called with call_usermodehelper. The function
call_usermodehelper starts the release_agent with a full set fo capabilities.
Therefore require capabilities when setting the release_agaent.
Reported-by: Tabitha Sable <tabitha.c.sable@gmail.com>
Tested-by: Tabitha Sable <tabitha.c.sable@gmail.com>
Fixes: 81a6a5cdd2 ("Task Control Groups: automatic userspace notification of idle cgroups")
Cc: stable@vger.kernel.org # v2.6.24+
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 20b0dfa86b upstream.
The original commit depended on a rework commit (724fc856c0 ("drm/vc4:
hdmi: Split the CEC disable / enable functions in two")) that
(rightfully) didn't reach stable.
However, probably because the context changed, when the patch was
applied to stable the pm_runtime_put called got moved to the end of the
vc4_hdmi_cec_adap_enable function (that would have become
vc4_hdmi_cec_disable with the rework) to vc4_hdmi_cec_init.
This means that at probe time, we now drop our reference to the clocks
and power domains and thus end up with a CPU hang when the CPU tries to
access registers.
The call to pm_runtime_resume_and_get() is also problematic since the
.adap_enable CEC hook is called both to enable and to disable the
controller. That means that we'll now call pm_runtime_resume_and_get()
at disable time as well, messing with the reference counting.
The behaviour we should have though would be to have
pm_runtime_resume_and_get() called when the CEC controller is enabled,
and pm_runtime_put when it's disabled.
We need to move things around a bit to behave that way, but it aligns
stable with upstream.
Cc: <stable@vger.kernel.org> # 5.10.x
Cc: <stable@vger.kernel.org> # 5.15.x
Cc: <stable@vger.kernel.org> # 5.16.x
Reported-by: Michael Stapelberg <michael+drm@stapelberg.ch>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7e570780e upstream.
Forcibly leave nested virtualization operation if userspace toggles SMM
state via KVM_SET_VCPU_EVENTS or KVM_SYNC_X86_EVENTS. If userspace
forces the vCPU out of SMM while it's post-VMXON and then injects an SMI,
vmx_enter_smm() will overwrite vmx->nested.smm.vmxon and end up with both
vmxon=false and smm.vmxon=false, but all other nVMX state allocated.
Don't attempt to gracefully handle the transition as (a) most transitions
are nonsencial, e.g. forcing SMM while L2 is running, (b) there isn't
sufficient information to handle all transitions, e.g. SVM wants access
to the SMRAM save state, and (c) KVM_SET_VCPU_EVENTS must precede
KVM_SET_NESTED_STATE during state restore as the latter disallows putting
the vCPU into L2 if SMM is active, and disallows tagging the vCPU as
being post-VMXON in SMM if SMM is not active.
Abuse of KVM_SET_VCPU_EVENTS manifests as a WARN and memory leak in nVMX
due to failure to free vmcs01's shadow VMCS, but the bug goes far beyond
just a memory leak, e.g. toggling SMM on while L2 is active puts the vCPU
in an architecturally impossible state.
WARNING: CPU: 0 PID: 3606 at free_loaded_vmcs arch/x86/kvm/vmx/vmx.c:2665 [inline]
WARNING: CPU: 0 PID: 3606 at free_loaded_vmcs+0x158/0x1a0 arch/x86/kvm/vmx/vmx.c:2656
Modules linked in:
CPU: 1 PID: 3606 Comm: syz-executor725 Not tainted 5.17.0-rc1-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:free_loaded_vmcs arch/x86/kvm/vmx/vmx.c:2665 [inline]
RIP: 0010:free_loaded_vmcs+0x158/0x1a0 arch/x86/kvm/vmx/vmx.c:2656
Code: <0f> 0b eb b3 e8 8f 4d 9f 00 e9 f7 fe ff ff 48 89 df e8 92 4d 9f 00
Call Trace:
<TASK>
kvm_arch_vcpu_destroy+0x72/0x2f0 arch/x86/kvm/x86.c:11123
kvm_vcpu_destroy arch/x86/kvm/../../../virt/kvm/kvm_main.c:441 [inline]
kvm_destroy_vcpus+0x11f/0x290 arch/x86/kvm/../../../virt/kvm/kvm_main.c:460
kvm_free_vcpus arch/x86/kvm/x86.c:11564 [inline]
kvm_arch_destroy_vm+0x2e8/0x470 arch/x86/kvm/x86.c:11676
kvm_destroy_vm arch/x86/kvm/../../../virt/kvm/kvm_main.c:1217 [inline]
kvm_put_kvm+0x4fa/0xb00 arch/x86/kvm/../../../virt/kvm/kvm_main.c:1250
kvm_vm_release+0x3f/0x50 arch/x86/kvm/../../../virt/kvm/kvm_main.c:1273
__fput+0x286/0x9f0 fs/file_table.c:311
task_work_run+0xdd/0x1a0 kernel/task_work.c:164
exit_task_work include/linux/task_work.h:32 [inline]
do_exit+0xb29/0x2a30 kernel/exit.c:806
do_group_exit+0xd2/0x2f0 kernel/exit.c:935
get_signal+0x4b0/0x28c0 kernel/signal.c:2862
arch_do_signal_or_restart+0x2a9/0x1c40 arch/x86/kernel/signal.c:868
handle_signal_work kernel/entry/common.c:148 [inline]
exit_to_user_mode_loop kernel/entry/common.c:172 [inline]
exit_to_user_mode_prepare+0x17d/0x290 kernel/entry/common.c:207
__syscall_exit_to_user_mode_work kernel/entry/common.c:289 [inline]
syscall_exit_to_user_mode+0x19/0x60 kernel/entry/common.c:300
do_syscall_64+0x42/0xb0 arch/x86/entry/common.c:86
entry_SYSCALL_64_after_hwframe+0x44/0xae
</TASK>
Cc: stable@vger.kernel.org
Reported-by: syzbot+8112db3ab20e70d50c31@syzkaller.appspotmail.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220125220358.2091737-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Backported-by: Tadeusz Struk <tadeusz.struk@linaro.org>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 998c0bd2b3 upstream.
We have seen cases where an endpoint RX completion interrupt arrives
while replenishing for the endpoint is underway. This causes another
instance of replenishing to begin as part of completing the receive
transaction. If this occurs it can lead to transaction corruption.
Use a new flag to ensure only one replenish instance for an endpoint
executes at a time.
Fixes: 84f9bd12d4 ("soc: qcom: ipa: IPA endpoints")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1aaa01dbf upstream.
Define a new replenish_flags bitmap to contain Boolean flags
associated with an endpoint's replenishing state. Replace the
replenish_enabled field with a flag in that bitmap. This is to
prepare for the next patch, which adds another flag.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c0e3b5ce9 upstream.
In ipa_endpoint_replenish(), if an error occurs when attempting to
replenish a receive buffer, we just quit and try again later. In
that case we increment the backlog count to reflect that the attempt
was unsuccessful. Then, if the add_one flag was true we increment
the backlog again.
This second increment is not included in the backlog local variable
though, and its value determines whether delayed work should be
scheduled. This is a bug.
Fix this by determining whether 1 or 2 should be added to the
backlog before adding it in a atomic_add_return() call.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Fixes: 84f9bd12d4 ("soc: qcom: ipa: IPA endpoints")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23584c1ed3 upstream.
The Power Fault Detected bit in the Slot Status register differs from
all other hotplug events in that it is sticky: It can only be cleared
after turning off slot power. Per PCIe r5.0, sec. 6.7.1.8:
If a power controller detects a main power fault on the hot-plug slot,
it must automatically set its internal main power fault latch [...].
The main power fault latch is cleared when software turns off power to
the hot-plug slot.
The stickiness used to cause interrupt storms and infinite loops which
were fixed in 2009 by commits 5651c48cfa ("PCI pciehp: fix power fault
interrupt storm problem") and 99f0169c17 ("PCI: pciehp: enable
software notification on empty slots").
Unfortunately in 2020 the infinite loop issue was inadvertently
reintroduced by commit 8edf5332c3 ("PCI: pciehp: Fix MSI interrupt
race"): The hardirq handler pciehp_isr() clears the PFD bit until
pciehp's power_fault_detected flag is set. That happens in the IRQ
thread pciehp_ist(), which never learns of the event because the hardirq
handler is stuck in an infinite loop. Fix by setting the
power_fault_detected flag already in the hardirq handler.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=214989
Link: https://lore.kernel.org/linux-pci/DM8PR11MB5702255A6A92F735D90A4446868B9@DM8PR11MB5702.namprd11.prod.outlook.com
Fixes: 8edf5332c3 ("PCI: pciehp: Fix MSI interrupt race")
Link: https://lore.kernel.org/r/66eaeef31d4997ceea357ad93259f290ededecfd.1637187226.git.lukas@wunner.de
Reported-by: Joseph Bao <joseph.bao@intel.com>
Tested-by: Joseph Bao <joseph.bao@intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v4.19+
Cc: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Polling at 100Hz for 1.5s consumes quite a bit of kworker time with no
obvious benefit. Reduce that polling rate to ~6Hz.
To further save CPU and power, defer the next poll if no energy is
detected.
See: https://github.com/raspberrypi/linux/issues/4780
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
CM4S has no HDMI1 output, so it is advisable to disable the controller
and its I2C interface in software. This is ordinarily done by setting
their status properties to "disabled", but the vc4-kms-v3d(-pi4)
overlay enables both HDMIs and DDCs as part of the transfer of control
from the VPU.
Knobble the CM4S dts in such a way that the overlay applies
successfully but the hdmi1 and ddc1 nodes remain disabled by changing
the compatible string to something unrecognised.
See: https://github.com/raspberrypi/linux/issues/4857
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The PCIE inbound window is rounded up to a power of 2, so the default
of 3GB rounds up to 4GB starting at 0. This prohibits the MSI vector
sitting at 0x0_fffffffc, and causes warnings from some subsystems
(eg ahci) of a 64bit address on a 32bit configuration.
Reduce the window down to 2GB to avoid this issue.
https://github.com/raspberrypi/linux/issues/4848
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Allow a user to specify the panel rotation in devicetree as 0, 90,
180, or 270 by setting a parameter.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
The second hdmi port on cm4s is disabled by default (default from
bcm2711-rpi.dtsi) and therefore it is not necessary to remove it in the
specific cm4s overlay (as done in 64328ab674)
Panel orientation is now handled by the drm_panel and
panel_bridge frameworks, so remove the custom handling.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Current usage of drm_connector_set_panel_orientation is from a panel's
get_modes call. However if the panel orientation property doesn't
exist on the connector at this point, then drm_mode_object triggers
WARNs as the connector is already registered.
Add an orientation variable to struct drm_panel and initialise it from
drm_panel_init.
panel_bridge_attach can then create the property before the connector
is registered.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The vc4-kms-kippah-7inch overlay has been replaced by the container
overlay vc4-kms-dpi-panel, using the "kippah-7inch" parameter. The
original overlay has been retained for now to avoid breaking
existing installations, but that doesn't make it any less deprecated,
so update the README accordingly.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The Geekworm MZP280 panel is a 480x640 (portrait) panel with a
capacitive touch interface and a 40 pin header meant to interface
directly with the Raspberry Pi. The screen is 2.8 inches diagonally,
and there appear to be at least 4 distinct versions all with the same
panel timings.
Timings were derived from drivers posted on the github located here:
https://github.com/tianyoujian/MZDPI/tree/master/vga
Additional details about this panel family can be found here:
https://wiki.geekworm.com/2.8_inch_Touch_Screen_for_Pi_zero
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Add the MEDIA_BUS_FMT_RGB565_1X24_CPADHI format used by the Geekworm
MZP280 panel for the Raspberry Pi.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Add support for MEDIA_BUS_FMT_RGB565_1X24_CPADHI. This format is used
by the Geekworm MZP280 panel which interfaces with the Raspberry Pi.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
commit a37d9a17f0 upstream.
Apparently, there are some applications that use IN_DELETE event as an
invalidation mechanism and expect that if they try to open a file with
the name reported with the delete event, that it should not contain the
content of the deleted file.
Commit 49246466a9 ("fsnotify: move fsnotify_nameremove() hook out of
d_delete()") moved the fsnotify delete hook before d_delete() so fsnotify
will have access to a positive dentry.
This allowed a race where opening the deleted file via cached dentry
is now possible after receiving the IN_DELETE event.
To fix the regression, create a new hook fsnotify_delete() that takes
the unlinked inode as an argument and use a helper d_delete_notify() to
pin the inode, so we can pass it to fsnotify_delete() after d_delete().
Backporting hint: this regression is from v5.3. Although patch will
apply with only trivial conflicts to v5.4 and v5.10, it won't build,
because fsnotify_delete() implementation is different in each of those
versions (see fsnotify_link()).
A follow up patch will fix the fsnotify_unlink/rmdir() calls in pseudo
filesystem that do not need to call d_delete().
Link: https://lore.kernel.org/r/20220120215305.282577-1-amir73il@gmail.com
Reported-by: Ivan Delalande <colona@arista.com>
Link: https://lore.kernel.org/linux-fsdevel/YeNyzoDM5hP5LtGW@visor/
Fixes: 49246466a9 ("fsnotify: move fsnotify_nameremove() hook out of d_delete()")
Cc: stable@vger.kernel.org # v5.3+
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10756dc5b0 upstream.
As linux/nfc.h userspace compilation was finally fixed by commits
79b69a8370 ("nfc: uapi: use kernel size_t to fix user-space builds")
and 7175f02c4e ("uapi: fix linux/nfc.h userspace compilation errors"),
there is no need to keep the compile-test exception for it in
usr/include/Makefile.
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fd20d97383 ]
When using per-vlan state, if vlan snooping and stats are disabled,
untagged or priority-tagged ingress frame will go to check pvid state.
If the port state is forwarding and the pvid state is not
learning/forwarding, untagged or priority-tagged frame will be dropped
but skb memory is not freed.
Should free skb when __allowed_ingress returns false.
Fixes: a580c76d53 ("net: bridge: vlan: add per-vlan state")
Signed-off-by: Tim Yi <tim.yi@pica8.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Link: https://lore.kernel.org/r/20220127074953.12632-1-tim.yi@pica8.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 970a5a3ea8 ]
In commit 431280eebe ("ipv4: tcp: send zero IPID for RST and
ACK sent in SYN-RECV and TIME-WAIT state") we took care of some
ctl packets sent by TCP.
It turns out we need to use a similar strategy for SYNACK packets.
By default, they carry IP_DF and IPID==0, but there are ways
to ask them to use the hashed IP ident generator and thus
be used to build off-path attacks.
(Ref: Off-Path TCP Exploits of the Mixed IPID Assignment)
One of this way is to force (before listener is started)
echo 1 >/proc/sys/net/ipv4/ip_no_pmtu_disc
Another way is using forged ICMP ICMP_FRAG_NEEDED
with a very small MTU (like 68) to force a false return from
ip_dont_fragment()
In this patch, ip_build_and_send_pkt() uses the following
heuristics.
1) Most SYNACK packets are smaller than IPV4_MIN_MTU and therefore
can use IP_DF regardless of the listener or route pmtu setting.
2) In case the SYNACK packet is bigger than IPV4_MIN_MTU,
we use prandom_u32() generator instead of the IPv4 hashed ident one.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Ray Che <xijiache@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Cc: Geoff Alexander <alexandg@cs.unm.edu>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dcb2c5c6ca ]
When dumping vlan options for a single net device we send the same
entries infinitely because user-space expects a 0 return at the end but
we keep returning skb->len and restarting the dump on retry. Fix it by
returning the value from br_vlan_dump_dev() if it completed or there was
an error. The only case that must return skb->len is when the dump was
incomplete and needs to continue (-EMSGSIZE).
Reported-by: Benjamin Poirier <bpoirier@nvidia.com>
Fixes: 8dcea18708 ("net: bridge: vlan: add rtm definitions and dump support")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36268983e9 ]
This reverts commit b75326c201.
This commit breaks Linux compatibility with USGv6 tests. The RFC this
commit was based on is actually an expired draft: no published RFC
currently allows the new behaviour it introduced.
Without full IETF endorsement, the flash renumbering scenario this
patch was supposed to enable is never going to work, as other IPv6
equipements on the same LAN will keep the 2 hours limit.
Fixes: b75326c201 ("ipv6: Honor all IPv6 PIO Valid Lifetime values")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f61353cd2 ]
Since some interrupt states may be cleared by hardware, the driver
may receive an empty interrupt. Currently, the VF driver directly
disables the vector0 interrupt in this case. As a result, the VF
is unavailable. Therefore, the vector0 interrupt should be enabled
in this case.
Fixes: b90fcc5bd9 ("net: hns3: add reset handling for VF when doing Core/Global/IMP reset")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c63003e3d9 ]
The cpsw driver didn't properly initialise the struct page_pool_params
before calling page_pool_create(), which leads to crashes after the struct
has been expanded with new parameters.
The second Fixes tag below is where the buggy code was introduced, but
because the code was moved around this patch will only apply on top of the
commit in the first Fixes tag.
Fixes: c5013ac1dd ("net: ethernet: ti: cpsw: move set of common functions in cpsw_priv")
Fixes: 9ed4050c0d ("net: ethernet: ti: cpsw: add XDP support")
Reported-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Tested-by: Colin Foster <colin.foster@in-advantage.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ff5549b1d ]
In the WIN10 version of the Synthetic Video protocol with Hyper-V,
Hyper-V reports a list of supported resolutions as part of the protocol
negotiation. The driver calculates the maximum width and height from
the list of resolutions, and uses those maximums to validate any screen
resolution specified in the video= option on the kernel boot line.
This method of validation is incorrect. For example, the list of
supported resolutions could contain 1600x1200 and 1920x1080, both of
which fit in an 8 Mbyte frame buffer. But calculating the max width
and height yields 1920 and 1200, and 1920x1200 resolution does not fit
in an 8 Mbyte frame buffer. Unfortunately, this resolution is accepted,
causing a kernel fault when the driver accesses memory outside the
frame buffer.
Instead, validate the specified screen resolution by calculating
its size, and comparing against the frame buffer size. Delete the
code for calculating the max width and height from the list of
resolutions, since these max values have no use. Also add the
frame buffer size to the info message to aid in understanding why
a resolution might be rejected.
Fixes: 67e7cdb482 ("video: hyperv: hyperv_fb: Obtain screen resolution from Hyper-V host")
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Acked-by: Helge Deller <deller@gmx.de>
Link: https://lore.kernel.org/r/1642360711-2335-1-git-send-email-mikelley@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48079e7fdd ]
ibmvnic_tasklet() continuously spins waiting for responses to all
capability requests. It does this to avoid encountering an error
during initialization of the vnic. However if there is a bug in the
VIOS and we do not receive a response to one or more queries the
tasklet ends up spinning continuously leading to hard lock ups.
If we fail to receive a message from the VIOS it is reasonable to
timeout the login attempt rather than spin indefinitely in the tasklet.
Fixes: 249168ad07 ("ibmvnic: Make CRQ interrupt tasklet wait for all capabilities crqs")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 151b6a5c06 ]
We use ->running_cap_crqs to determine when the ibmvnic_tasklet() should
send out the next protocol message type. i.e when we get back responses
to all our QUERY_CAPABILITY CRQs we send out REQUEST_CAPABILITY crqs.
Similiary, when we get responses to all the REQUEST_CAPABILITY crqs, we
send out the QUERY_IP_OFFLOAD CRQ.
We currently increment ->running_cap_crqs as we send out each CRQ and
have the ibmvnic_tasklet() send out the next message type, when this
running_cap_crqs count drops to 0.
This assumes that all the CRQs of the current type were sent out before
the count drops to 0. However it is possible that we send out say 6 CRQs,
get preempted and receive all the 6 responses before we send out the
remaining CRQs. This can result in ->running_cap_crqs count dropping to
zero before all messages of the current type were sent and we end up
sending the next protocol message too early.
Instead initialize the ->running_cap_crqs upfront so the tasklet will
only send the next protocol message after all responses are received.
Use the cap_reqs local variable to also detect any discrepancy (either
now or in future) in the number of capability requests we actually send.
Currently only send_query_cap() is affected by this behavior (of sending
next message early) since it is called from the worker thread (during
reset) and from application thread (during ->ndo_open()) and they can be
preempted. send_request_cap() is only called from the tasklet which
processes CRQ responses sequentially, is not be affected. But to
maintain the existing symmtery with send_query_capability() we update
send_request_capability() also.
Fixes: 249168ad07 ("ibmvnic: Make CRQ interrupt tasklet wait for all capabilities crqs")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27a8caa59b ]
During IP fragmentation we sanitize IP options. This means overwriting
options which should not be copied with NOPs. Only the first fragment
has the original, full options.
ip_fraglist_prepare() copies the IP header and options from previous
fragment to the next one. Commit 19c3401a91 ("net: ipv4: place control
buffer handling away from fragmentation iterators") moved sanitizing
options before ip_fraglist_prepare() which means options are sanitized
and then overwritten again with the old values.
Fixing this is not enough, however, nor did the sanitization work
prior to aforementioned commit.
ip_options_fragment() (which does the sanitization) uses ipcb->opt.optlen
for the length of the options. ipcb->opt of fragments is not populated
(it's 0), only the head skb has the state properly built. So even when
called at the right time ip_options_fragment() does nothing. This seems
to date back all the way to v2.5.44 when the fast path for pre-fragmented
skbs had been introduced. Prior to that ip_options_build() would have been
called for every fragment (in fact ever since v2.5.44 the fragmentation
handing in ip_options_build() has been dead code, I'll clean it up in
-next).
In the original patch (see Link) caixf mentions fixing the handling
for fragments other than the second one, but I'm not sure how _any_
fragment could have had their options sanitized with the code
as it stood.
Tested with python (MTU on lo lowered to 1000 to force fragmentation):
import socket
s = socket.socket(socket.AF_INET, socket.SOCK_DGRAM)
s.setsockopt(socket.IPPROTO_IP, socket.IP_OPTIONS,
bytearray([7,4,5,192, 20|0x80,4,1,0]))
s.sendto(b'1'*2000, ('127.0.0.1', 1234))
Before:
IP (tos 0x0, ttl 64, id 1053, offset 0, flags [+], proto UDP (17), length 996, options (RR [bad length 4] [bad ptr 5] 192.148.4.1,,RA value 256))
localhost.36500 > localhost.search-agent: UDP, length 2000
IP (tos 0x0, ttl 64, id 1053, offset 968, flags [+], proto UDP (17), length 996, options (RR [bad length 4] [bad ptr 5] 192.148.4.1,,RA value 256))
localhost > localhost: udp
IP (tos 0x0, ttl 64, id 1053, offset 1936, flags [none], proto UDP (17), length 100, options (RR [bad length 4] [bad ptr 5] 192.148.4.1,,RA value 256))
localhost > localhost: udp
After:
IP (tos 0x0, ttl 96, id 42549, offset 0, flags [+], proto UDP (17), length 996, options (RR [bad length 4] [bad ptr 5] 192.148.4.1,,RA value 256))
localhost.51607 > localhost.search-agent: UDP, bad length 2000 > 960
IP (tos 0x0, ttl 96, id 42549, offset 968, flags [+], proto UDP (17), length 996, options (NOP,NOP,NOP,NOP,RA value 256))
localhost > localhost: udp
IP (tos 0x0, ttl 96, id 42549, offset 1936, flags [none], proto UDP (17), length 100, options (NOP,NOP,NOP,NOP,RA value 256))
localhost > localhost: udp
RA (20 | 0x80) is now copied as expected, RR (7) is "NOPed out".
Link: https://lore.kernel.org/netdev/20220107080559.122713-1-ooppublic@163.com/
Fixes: 19c3401a91 ("net: ipv4: place control buffer handling away from fragmentation iterators")
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: caixf <ooppublic@163.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit faf482ca19 ]
The ip_options_fragment() only called when iter->offset is equal to zero,
so move it out of loop, and inline 'Copy the flags to each fragment.'
As also, remove the unused parameter in ip_frag_ipcb().
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a53fff96f3 ]
Experiments with MAX6654 show that its alert function is broken,
similar to other chips supported by the lm90 driver. Mark it accordingly.
Fixes: 229d495d81 ("hwmon: (lm90) Add max6654 support to lm90 driver")
Cc: Josh Lehan <krellan@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e9b7c3a426 ]
The kernel is aligned at SEGMENT_SIZE and this is the size populated in the PE
headers:
arch/arm64/kernel/efi-header.S: .long SEGMENT_ALIGN // SectionAlignment
EFI_KIMG_ALIGN is defined as: (SEGMENT_ALIGN > THREAD_ALIGN ? SEGMENT_ALIGN :
THREAD_ALIGN)
So it depends on THREAD_ALIGN. On newer builds this message started to appear
even though the loader is taking into account the PE header (which is stating
SEGMENT_ALIGN).
Fixes: c32ac11da3 ("efi/libstub: arm64: Double check image alignment at entry")
Signed-off-by: Mihai Carabas <mihai.carabas@oracle.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c13c05c5f ]
Improve retransmission backoff by only backing off when we retransmit data
packets rather than when we set the lost ack timer.
To this end:
(1) In rxrpc_resend(), use rxrpc_get_rto_backoff() when setting the
retransmission timer and only tell it that we are retransmitting if we
actually have things to retransmit.
Note that it's possible for the retransmission algorithm to race with
the processing of a received ACK, so we may see no packets needing
retransmission.
(2) In rxrpc_send_data_packet(), don't bump the backoff when setting the
ack_lost_at timer, as it may then get bumped twice.
With this, when looking at one particular packet, the retransmission
intervals were seen to be 1.5ms, 2ms, 3ms, 5ms, 9ms, 17ms, 33ms, 71ms,
136ms, 264ms, 544ms, 1.088s, 2.1s, 4.2s and 8.3s.
Fixes: c410bf0193 ("rxrpc: Fix the excessive initial retransmission timeout")
Suggested-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
Tested-by: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/r/164138117069.2023386.17446904856843997127.stgit@warthog.procyon.org.uk/
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8db854be2 ]
PF forwards its VF messages to AF and corresponding
replies from AF to VF. AF sets proper error code in the
replies after processing message requests. Currently PF
checks the error codes in replies and sends invalid
message to VF. This way VF lacks the information of
error code set by AF for its messages. This patch
changes that such that PF simply forwards AF replies
so that VF can handle error codes.
Fixes: d424b6c024 ("octeontx2-pf: Enable SRIOV and added VF mbox handling")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbda1b1668 ]
Commit bafbdd527d ("phylib: Add device reset GPIO support") added call
to phy_device_reset(phydev) after the put_device() call in phy_detach().
The comment before the put_device() call says that the phydev might go
away with put_device().
Fix potential use-after-free by calling phy_device_reset() before
put_device().
Fixes: bafbdd527d ("phylib: Add device reset GPIO support")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220119162748.32418-1-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d15c7e875d ]
A problem was encountered with the Bel-Fuse 1GBT-SFP05 SFP module (which
is a 1 Gbps copper module operating in SGMII mode with an internal
BCM54616S PHY device) using the Xilinx AXI Ethernet MAC core, where the
module would work properly on the initial insertion or boot of the
device, but after the device was rebooted, the link would either only
come up at 100 Mbps speeds or go up and down erratically.
I found no meaningful changes in the PHY configuration registers between
the working and non-working boots, but the status registers seemed to
have a lot of error indications set on the SERDES side of the device on
the non-working boot. I suspect the problem is that whatever happens on
the SGMII link when the device is rebooted and the FPGA logic gets
reloaded ends up putting the module's onboard PHY into a bad state.
Since commit 6e2d85ec05 ("net: phy: Stop with excessive soft reset")
the genphy_soft_reset call is not made automatically by the PHY core
unless the callback is explicitly specified in the driver structure. For
most of these Broadcom devices, there is probably a hardware reset that
gets asserted to reset the PHY during boot, however for SFP modules
(where the BCM54616S is commonly found) no such reset line exists, so if
the board keeps the SFP cage powered up across a reboot, it will end up
with no reset occurring during reboots.
Hook up the genphy_soft_reset callback for BCM54616S to ensure that a
PHY reset is performed before the device is initialized. This appears to
fix the issue with erratic operation after a reboot with this SFP
module.
Fixes: 6e2d85ec05 ("net: phy: Stop with excessive soft reset")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 98b0d89022 ]
Rick reported performance regressions in bugzilla because of cpu frequency
being lower than before:
https://bugzilla.kernel.org/show_bug.cgi?id=215045
He bisected the problem to:
commit 1c35b07e6d ("sched/fair: Ensure _sum and _avg values stay consistent")
This commit forces util_sum to be synced with the new util_avg after
removing the contribution of a task and before the next periodic sync. By
doing so util_sum is rounded to its lower bound and might lost up to
LOAD_AVG_MAX-1 of accumulated contribution which has not yet been
reflected in util_avg.
Instead of always setting util_sum to the low bound of util_avg, which can
significantly lower the utilization of root cfs_rq after propagating the
change down into the hierarchy, we revert the change of util_sum and
propagate the difference.
In addition, we also check that cfs's util_sum always stays above the
lower bound for a given util_avg as it has been observed that
sched_entity's util_sum is sometimes above cfs one.
Fixes: 1c35b07e6d ("sched/fair: Ensure _sum and _avg values stay consistent")
Reported-by: Rick Yiu <rickyiu@google.com>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Tested-by: Sachin Sant <sachinp@linux.ibm.com>
Link: https://lkml.kernel.org/r/20220111134659.24961-2-vincent.guittot@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09f5e7dc7a ]
Time readers that cannot take locks (due to NMI etc..) currently make
use of perf_event::shadow_ctx_time, which, for that event gives:
time' = now + (time - timestamp)
or, alternatively arranged:
time' = time + (now - timestamp)
IOW, the progression of time since the last time the shadow_ctx_time
was updated.
There's problems with this:
A) the shadow_ctx_time is per-event, even though the ctx_time it
reflects is obviously per context. The direct concequence of this
is that the context needs to iterate all events all the time to
keep the shadow_ctx_time in sync.
B) even with the prior point, the context itself might not be active
meaning its time should not advance to begin with.
C) shadow_ctx_time isn't consistently updated when ctx_time is
There are 3 users of this stuff, that suffer differently from this:
- calc_timer_values()
- perf_output_read()
- perf_event_update_userpage() /* A */
- perf_event_read_local() /* A,B */
In particular, perf_output_read() doesn't suffer at all, because it's
sample driven and hence only relevant when the event is actually
running.
This same was supposed to be true for perf_event_update_userpage(),
after all self-monitoring implies the context is active *HOWEVER*, as
per commit f792565326 ("perf/core: fix userpage->time_enabled of
inactive events") this goes wrong when combined with counter
overcommit, in that case those events that do not get scheduled when
the context becomes active (task events typically) miss out on the
EVENT_TIME update and ENABLED time is inflated (for a little while)
with the time the context was inactive. Once the event gets rotated
in, this gets corrected, leading to a non-monotonic timeflow.
perf_event_read_local() made things even worse, it can request time at
any point, suffering all the problems perf_event_update_userpage()
does and more. Because while perf_event_update_userpage() is limited
by the context being active, perf_event_read_local() users have no
such constraint.
Therefore, completely overhaul things and do away with
perf_event::shadow_ctx_time. Instead have regular context time updates
keep track of this offset directly and provide perf_event_time_now()
to complement perf_event_time().
perf_event_time_now() will, in adition to being context wide, also
take into account if the context is active. For inactive context, it
will not advance time.
This latter property means the cgroup perf_cgroup_info context needs
to grow addition state to track this.
Additionally, since all this is strictly per-cpu, we can use barrier()
to order context activity vs context time.
Fixes: 7d9285e82d ("perf/bpf: Extend the perf_event_read_local() interface, a.k.a. "bpf: perf event change needed for subsequent bpf helpers"")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Song Liu <song@kernel.org>
Tested-by: Namhyung Kim <namhyung@kernel.org>
Link: https://lkml.kernel.org/r/YcB06DasOBtU0b00@hirez.programming.kicks-ass.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 830af2eba4 ]
The packet isn't invalid, REPEAT means we're trying again after cleaning
out a stale connection, e.g. via tcp tracker.
This caused increases of invalid stat counter in a test case involving
frequent connection reuse, even though no packet is actually invalid.
Fixes: 56a62e2218 ("netfilter: conntrack: fix NF_REPEAT handling")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f5f766d5f ]
Johan reported the below crash with test_bpf on ppc64 e5500:
test_bpf: #296 ALU_END_FROM_LE 64: 0x0123456789abcdef -> 0x67452301 jited:1
Oops: Exception in kernel mode, sig: 4 [#1]
BE PAGE_SIZE=4K SMP NR_CPUS=24 QEMU e500
Modules linked in: test_bpf(+)
CPU: 0 PID: 76 Comm: insmod Not tainted 5.14.0-03771-g98c2059e008a-dirty #1
NIP: 8000000000061c3c LR: 80000000006dea64 CTR: 8000000000061c18
REGS: c0000000032d3420 TRAP: 0700 Not tainted (5.14.0-03771-g98c2059e008a-dirty)
MSR: 0000000080089000 <EE,ME> CR: 88002822 XER: 20000000 IRQMASK: 0
<...>
NIP [8000000000061c3c] 0x8000000000061c3c
LR [80000000006dea64] .__run_one+0x104/0x17c [test_bpf]
Call Trace:
.__run_one+0x60/0x17c [test_bpf] (unreliable)
.test_bpf_init+0x6a8/0xdc8 [test_bpf]
.do_one_initcall+0x6c/0x28c
.do_init_module+0x68/0x28c
.load_module+0x2460/0x2abc
.__do_sys_init_module+0x120/0x18c
.system_call_exception+0x110/0x1b8
system_call_common+0xf0/0x210
--- interrupt: c00 at 0x101d0acc
<...>
---[ end trace 47b2bf19090bb3d0 ]---
Illegal instruction
The illegal instruction turned out to be 'ldbrx' emitted for
BPF_FROM_[L|B]E, which was only introduced in ISA v2.06. Guard use of
the same and implement an alternative approach for older processors.
Fixes: 156d0e290e ("powerpc/ebpf/jit: Implement JIT compiler for extended BPF")
Reported-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Tested-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Acked-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/d1e51c6fdf572062cf3009a751c3406bda01b832.1641468127.git.naveen.n.rao@linux.vnet.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ff9d99bb8 ]
Renaming a file is required by POSIX to update the file ctime, so
ensure that the file data is synced to disk so that we don't clobber the
updated ctime by writing back after creating the hard link.
Fixes: f2c2c552f1 ("NFS: Move delegation recall into the NFSv4 callback for rename_setup()")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 204975036b ]
Creating a hard link is required by POSIX to update the file ctime, so
ensure that the file data is synced to disk so that we don't clobber the
updated ctime by writing back after creating the hard link.
Fixes: 9f76827287 ("NFS: Move the delegation return down into nfs4_proc_link()")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1d10f8a1f4 upstream.
After commit:7866a621043f ("dev: add per net_device packet type chains"),
we can not get packet types that are bound to a specified net device by
/proc/net/ptype, this patch fix the regression.
Run "tcpdump -i ens192 udp -nns0" Before and after apply this patch:
Before:
[root@localhost ~]# cat /proc/net/ptype
Type Device Function
0800 ip_rcv
0806 arp_rcv
86dd ipv6_rcv
After:
[root@localhost ~]# cat /proc/net/ptype
Type Device Function
ALL ens192 tpacket_rcv
0800 ip_rcv
0806 arp_rcv
86dd ipv6_rcv
v1 -> v2:
- fix the regression rather than adding new /proc API as
suggested by Stephen Hemminger.
Fixes: 7866a62104 ("dev: add per net_device packet type chains")
Signed-off-by: Jianguo Wu <wujianguo@chinatelecom.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1751fc1db3 upstream.
If the file type changes back to being a regular file on the server
between the failed OPEN and our LOOKUP, then we need to re-run the OPEN.
Fixes: 0dd2b474d0 ("nfs: implement i_op->atomic_open()")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac795161c9 upstream.
If the application sets the O_DIRECTORY flag, and tries to open a
regular file, nfs_atomic_open() will punt to doing a regular lookup.
If the server then returns a regular file, we will happily return a
file descriptor with uninitialised open state.
The fix is to return the expected ENOTDIR error in these cases.
Reported-by: Lyu Tao <tao.lyu@epfl.ch>
Fixes: 0dd2b474d0 ("nfs: implement i_op->atomic_open()")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a66c5ed539 ]
According to its datasheet, G781 supports a maximum conversion rate value
of 8 (62.5 ms). However, chips labeled G781 and G780 were found to only
support a maximum conversion rate value of 7 (125 ms). On the other side,
chips labeled G781-1 and G784 were found to support a conversion rate value
of 8. There is no known means to distinguish G780 from G781 or G784; all
chips report the same manufacturer ID and chip revision.
Setting the conversion rate register value to 8 on chips not supporting
it causes unexpected behavior since the real conversion rate is set to 0
(16 seconds) if a value of 8 is written into the conversion rate register.
Limit the conversion rate register value to 7 for all G78x chips to avoid
the problem.
Fixes: ae544f64cc ("hwmon: (lm90) Add support for GMT G781")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 23f57406b8 upstream.
ip_select_ident_segs() has been very conservative about using
the connected socket private generator only for packets with IP_DF
set, claiming it was needed for some VJ compression implementations.
As mentioned in this referenced document, this can be abused.
(Ref: Off-Path TCP Exploits of the Mixed IPID Assignment)
Before switching to pure random IPID generation and possibly hurt
some workloads, lets use the private inet socket generator.
Not only this will remove one vulnerability, this will also
improve performance of TCP flows using pmtudisc==IP_PMTUDISC_DONT
Fixes: 73f156a6e8 ("inetpeer: get rid of ip_id_count")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reported-by: Ray Che <xijiache@gmail.com>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2afc3b5a31 upstream.
When 'ping' changes to use PING socket instead of RAW socket by:
# sysctl -w net.ipv4.ping_group_range="0 100"
the selftests 'router_broadcast.sh' will fail, as such command
# ip vrf exec vrf-h1 ping -I veth0 198.51.100.255 -b
can't receive the response skb by the PING socket. It's caused by mismatch
of sk_bound_dev_if and dif in ping_rcv() when looking up the PING socket,
as dif is vrf-h1 if dif's master was set to vrf-h1.
This patch is to fix this regression by also checking the sk_bound_dev_if
against sdif so that the packets can stil be received even if the socket
is not bound to the vrf device but to the real iif.
Fixes: c319b4d76b ("net: ipv4: add IPPROTO_ICMP socket kind")
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 94746b0ba4 upstream.
Experiments with MAX6680 and MAX6681 show that the alert function of those
chips is broken, similar to other chips supported by the lm90 driver.
Mark it accordingly.
Fixes: 4667bcb8d8 ("hwmon: (lm90) Introduce chip parameter structure")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f614629f9c upstream.
Experiments with MAX6646 and MAX6648 show that the alert function of those
chips is broken, similar to other chips supported by the lm90 driver.
Mark it accordingly.
Fixes: 4667bcb8d8 ("hwmon: (lm90) Introduce chip parameter structure")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47934e06b6 upstream.
In one net namespace, after creating a packet socket without binding
it to a device, users in other net namespaces can observe the new
`packet_type` added by this packet socket by reading `/proc/net/ptype`
file. This is minor information leakage as packet socket is
namespace aware.
Add a net pointer in `packet_type` to keep the net namespace of
of corresponding packet socket. In `ptype_seq_show`, this net pointer
must be checked when it is not NULL.
Fixes: 2feb27dbe0 ("[NETNS]: Minor information leak via /proc/net/ptype file.")
Signed-off-by: Congyu Liu <liu3101@purdue.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6cee105e7f upstream.
The warning messages can be invoked from the data path for every packet
transmitted through an ip6gre netdev, leading to high CPU utilization.
Fix that by rate limiting the messages.
Fixes: 09c6bbf090 ("[IPV6]: Do mandatory IPv6 tunnel endpoint checks in realtime")
Reported-by: Maksym Yaremchuk <maksymy@nvidia.com>
Tested-by: Maksym Yaremchuk <maksymy@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3b8428b845 upstream.
Change i40e_update_vsi_stats and struct i40e_vsi to use u64 fields to match
the width of the stats counters in struct i40e_rx_queue_stats.
Update debugfs code to use the correct format specifier for u64.
Fixes: 41c445ff0f ("i40e: main driver core")
Signed-off-by: Joe Damato <jdamato@fastly.com>
Reported-by: kernel test robot <lkp@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f344c8129 upstream.
Fix for failed to init adminq: -53 while VF is resetting via MAC
address changing procedure.
Added sync module to avoid reading deadbeef value in reinit adminq
during software reset.
Without this patch it is possible to trigger VF reset procedure
during reinit adminq. This resulted in an incorrect reading of
value from the AQP registers and generated the -53 error.
Fixes: 5c3c48ac6b ("i40e: implement virtual device interface")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92947844b8 upstream.
When XDP was configured on a system with large number of CPUs
and X722 NIC there was a call trace with NULL pointer dereference.
i40e 0000:87:00.0: failed to get tracking for 256 queues for VSI 0 err -12
i40e 0000:87:00.0: setup of MAIN VSI failed
BUG: kernel NULL pointer dereference, address: 0000000000000000
RIP: 0010:i40e_xdp+0xea/0x1b0 [i40e]
Call Trace:
? i40e_reconfig_rss_queues+0x130/0x130 [i40e]
dev_xdp_install+0x61/0xe0
dev_xdp_attach+0x18a/0x4c0
dev_change_xdp_fd+0x1e6/0x220
do_setlink+0x616/0x1030
? ahci_port_stop+0x80/0x80
? ata_qc_issue+0x107/0x1e0
? lock_timer_base+0x61/0x80
? __mod_timer+0x202/0x380
rtnl_setlink+0xe5/0x170
? bpf_lsm_binder_transaction+0x10/0x10
? security_capable+0x36/0x50
rtnetlink_rcv_msg+0x121/0x350
? rtnl_calcit.isra.0+0x100/0x100
netlink_rcv_skb+0x50/0xf0
netlink_unicast+0x1d3/0x2a0
netlink_sendmsg+0x22a/0x440
sock_sendmsg+0x5e/0x60
__sys_sendto+0xf0/0x160
? __sys_getsockname+0x7e/0xc0
? _copy_from_user+0x3c/0x80
? __sys_setsockopt+0xc8/0x1a0
__x64_sys_sendto+0x20/0x30
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f83fa7a39e0
This was caused by PF queue pile fragmentation due to
flow director VSI queue being placed right after main VSI.
Because of this main VSI was not able to resize its
queue allocation for XDP resulting in no queues allocated
for main VSI when XDP was turned on.
Fix this by always allocating last queue in PF queue pile
for a flow director VSI.
Fixes: 41c445ff0f ("i40e: main driver core")
Fixes: 74608d17fe ("i40e: add support for XDP_TX action")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d701658a50 upstream.
Before this patch VF interface vanished when
maximum queue number was exceeded. Driver tried
to add next queues even if there was not enough
space. PF sent incorrect number of queues to
the VF when there were not enough of them.
Add an additional condition introduced to check
available space in 'qp_pile' before proceeding.
This condition makes it impossible to add queues
if they number is greater than the number resulting
from available space.
Also add the search for free space in PF queue
pair piles.
Without this patch VF interfaces are not seen
when available space for queues has been
exceeded and following logs appears permanently
in dmesg:
"Unable to get VF config (-32)".
"VF 62 failed opcode 3, retval: -5"
"Unable to get VF config due to PF error condition, not retrying"
Fixes: 7daa6bf329 ("i40e: driver core headers")
Fixes: 41c445ff0f ("i40e: main driver core")
Signed-off-by: Jaroslaw Gawin <jaroslawx.gawin@intel.com>
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b13bd5313 upstream.
Recently simplified i40e_rebuild causes that FW sometimes
is not ready after NVM update, the ping does not return.
Increase the delay in case of EMP reset.
Old delay of 300 ms was introduced for specific cards for 710 series.
Now it works for all the cards and delay was increased.
Fixes: 1fa51a650e ("i40e: Add delay after EMP reset for firmware to recover")
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d37823c352 upstream.
It has been reported some configuration where the kernel doesn't
boot with KASAN enabled.
This is due to wrong BAT allocation for the KASAN area:
---[ Data Block Address Translation ]---
0: 0xc0000000-0xcfffffff 0x00000000 256M Kernel rw m
1: 0xd0000000-0xdfffffff 0x10000000 256M Kernel rw m
2: 0xe0000000-0xefffffff 0x20000000 256M Kernel rw m
3: 0xf8000000-0xf9ffffff 0x2a000000 32M Kernel rw m
4: 0xfa000000-0xfdffffff 0x2c000000 64M Kernel rw m
A BAT must have both virtual and physical addresses alignment matching
the size of the BAT. This is not the case for BAT 4 above.
Fix kasan_init_region() by using block_size() function that is in
book3s32/mmu.c. To be able to reuse it here, make it non static and
change its name to bat_block_size() in order to avoid name conflict
with block_size() defined in <linux/blkdev.h>
Also reuse find_free_bat() to avoid an error message from setbat()
when no BAT is available.
And allocate memory outside of linear memory mapping to avoid
wasting that precious space.
With this change we get correct alignment for BATs and KASAN shadow
memory is allocated outside the linear memory space.
---[ Data Block Address Translation ]---
0: 0xc0000000-0xcfffffff 0x00000000 256M Kernel rw
1: 0xd0000000-0xdfffffff 0x10000000 256M Kernel rw
2: 0xe0000000-0xefffffff 0x20000000 256M Kernel rw
3: 0xf8000000-0xfbffffff 0x7c000000 64M Kernel rw
4: 0xfc000000-0xfdffffff 0x7a000000 32M Kernel rw
Fixes: 7974c47326 ("powerpc/32s: Implement dedicated kasan_init_region()")
Cc: stable@vger.kernel.org
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Tested-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/7a50ef902494d1325227d47d33dada01e52e5518.1641818726.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 37eb7ca91b upstream.
Today we have the following IBATs allocated:
---[ Instruction Block Address Translation ]---
0: 0xc0000000-0xc03fffff 0x00000000 4M Kernel x m
1: 0xc0400000-0xc05fffff 0x00400000 2M Kernel x m
2: 0xc0600000-0xc06fffff 0x00600000 1M Kernel x m
3: 0xc0700000-0xc077ffff 0x00700000 512K Kernel x m
4: 0xc0780000-0xc079ffff 0x00780000 128K Kernel x m
5: 0xc07a0000-0xc07bffff 0x007a0000 128K Kernel x m
6: -
7: -
The two 128K should be a single 256K instead.
When _etext is not aligned to 128Kbytes, the system will allocate
all necessary BATs to the lower 128Kbytes boundary, then allocate
an additional 128Kbytes BAT for the remaining block.
Instead, align the top to 128Kbytes so that the function directly
allocates a 256Kbytes last block:
---[ Instruction Block Address Translation ]---
0: 0xc0000000-0xc03fffff 0x00000000 4M Kernel x m
1: 0xc0400000-0xc05fffff 0x00400000 2M Kernel x m
2: 0xc0600000-0xc06fffff 0x00600000 1M Kernel x m
3: 0xc0700000-0xc077ffff 0x00700000 512K Kernel x m
4: 0xc0780000-0xc07bffff 0x00780000 256K Kernel x m
5: -
6: -
7: -
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/ab58b296832b0ec650e2203200e060adbcb2677d.1637930421.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f52b0aba6 upstream.
Changes to the AMD Thresholding sysfs code prevents sysfs writes from
updating the underlying registers once CPU init is completed, i.e.
"threshold_banks" is set.
Allow the registers to be updated if the thresholding interface is
already initialized or if in the init path. Use the "set_lvt_off" value
to indicate if running in the init path, since this value is only set
during init.
Fixes: a037f3ca0e ("x86/mce/amd: Make threshold bank setting hotplug robust")
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220117161328.19148-1-yazen.ghannam@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 809232619f upstream.
The membarrier command MEMBARRIER_CMD_QUERY allows querying the
available membarrier commands. When the membarrier-rseq fence commands
were added, a new MEMBARRIER_CMD_PRIVATE_EXPEDITED_RSEQ_BITMASK was
introduced with the intent to expose them with the MEMBARRIER_CMD_QUERY
command, the but it was never added to MEMBARRIER_CMD_BITMASK.
The membarrier-rseq fence commands are therefore not wired up with the
query command.
Rename MEMBARRIER_CMD_PRIVATE_EXPEDITED_RSEQ_BITMASK to
MEMBARRIER_PRIVATE_EXPEDITED_RSEQ_BITMASK (the bitmask is not a command
per-se), and change the erroneous
MEMBARRIER_CMD_REGISTER_PRIVATE_EXPEDITED_RSEQ_BITMASK (which does not
actually exist) to MEMBARRIER_CMD_REGISTER_PRIVATE_EXPEDITED_RSEQ.
Wire up MEMBARRIER_PRIVATE_EXPEDITED_RSEQ_BITMASK in
MEMBARRIER_CMD_BITMASK. Fixing this allows discovering availability of
the membarrier-rseq fence feature.
Fixes: 2a36ab717e ("rseq/membarrier: Add MEMBARRIER_CMD_PRIVATE_EXPEDITED_RSEQ")
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org> # 5.10+
Link: https://lkml.kernel.org/r/20220117203010.30129-1-mathieu.desnoyers@efficios.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90b8aa9f5b upstream.
With some chargers, vbus might momentarily raise above VSAFE5V and fall
back to 0V before tcpm gets to read port->tcpc->get_vbus. This will
will report a VBUS off event causing TCPM to transition to
SNK_UNATTACHED where it should be waiting in either SNK_ATTACH_WAIT
or SNK_DEBOUNCED state. This patch makes TCPM avoid vbus off events
while in SNK_ATTACH_WAIT or SNK_DEBOUNCED state.
Stub from the spec:
"4.5.2.2.4.2 Exiting from AttachWait.SNK State
A Sink shall transition to Unattached.SNK when the state of both
the CC1 and CC2 pins is SNK.Open for at least tPDDebounce.
A DRP shall transition to Unattached.SRC when the state of both
the CC1 and CC2 pins is SNK.Open for at least tPDDebounce."
[23.194131] CC1: 0 -> 0, CC2: 0 -> 5 [state SNK_UNATTACHED, polarity 0, connected]
[23.201777] state change SNK_UNATTACHED -> SNK_ATTACH_WAIT [rev3 NONE_AMS]
[23.209949] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS]
[23.300579] VBUS off
[23.300668] state change SNK_ATTACH_WAIT -> SNK_UNATTACHED [rev3 NONE_AMS]
[23.301014] VBUS VSAFE0V
[23.301111] Start toggling
Fixes: f0690a25a1 ("staging: typec: USB Type-C Port Manager (tcpm)")
Cc: stable@vger.kernel.org
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20220122015520.332507-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26fbe9772b upstream.
The syzbot fuzzer has identified a bug in which processes hang waiting
for usb_kill_urb() to return. It turns out the issue is not unlinking
the URB; that works just fine. Rather, the problem arises when the
wakeup notification that the URB has completed is not received.
The reason is memory-access ordering on SMP systems. In outline form,
usb_kill_urb() and __usb_hcd_giveback_urb() operating concurrently on
different CPUs perform the following actions:
CPU 0 CPU 1
---------------------------- ---------------------------------
usb_kill_urb(): __usb_hcd_giveback_urb():
... ...
atomic_inc(&urb->reject); atomic_dec(&urb->use_count);
... ...
wait_event(usb_kill_urb_queue,
atomic_read(&urb->use_count) == 0);
if (atomic_read(&urb->reject))
wake_up(&usb_kill_urb_queue);
Confining your attention to urb->reject and urb->use_count, you can
see that the overall pattern of accesses on CPU 0 is:
write urb->reject, then read urb->use_count;
whereas the overall pattern of accesses on CPU 1 is:
write urb->use_count, then read urb->reject.
This pattern is referred to in memory-model circles as SB (for "Store
Buffering"), and it is well known that without suitable enforcement of
the desired order of accesses -- in the form of memory barriers -- it
is entirely possible for one or both CPUs to execute their reads ahead
of their writes. The end result will be that sometimes CPU 0 sees the
old un-decremented value of urb->use_count while CPU 1 sees the old
un-incremented value of urb->reject. Consequently CPU 0 ends up on
the wait queue and never gets woken up, leading to the observed hang
in usb_kill_urb().
The same pattern of accesses occurs in usb_poison_urb() and the
failure pathway of usb_hcd_submit_urb().
The problem is fixed by adding suitable memory barriers. To provide
proper memory-access ordering in the SB pattern, a full barrier is
required on both CPUs. The atomic_inc() and atomic_dec() accesses
themselves don't provide any memory ordering, but since they are
present, we can use the optimized smp_mb__after_atomic() memory
barrier in the various routines to obtain the desired effect.
This patch adds the necessary memory barriers.
CC: <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+76629376e06e2c2ad626@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/Ye8K0QYee0Q0Nna2@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e3dd4a624 upstream.
Commit 7495af9308 ("ARM: multi_v7_defconfig: Enable drivers for
DragonBoard 410c") enables the CONFIG_PHY_QCOM_USB_HS for the ARM
multi_v7_defconfig. Enabling this Kconfig is causing the kernel to crash
on the Tegra20 Ventana platform in the ulpi_match() function.
The Qualcomm USB HS PHY driver that is enabled by CONFIG_PHY_QCOM_USB_HS,
registers a ulpi_driver but this driver does not provide an 'id_table',
so when ulpi_match() is called on the Tegra20 Ventana platform, it
crashes when attempting to deference the id_table pointer which is not
valid. The Qualcomm USB HS PHY driver uses device-tree for matching the
ULPI driver with the device and so fix this crash by using device-tree
for matching if the id_table is not valid.
Fixes: ef6a7bcfb0 ("usb: ulpi: Support device discovery via DT")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20220117150039.44058-1-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b67b31503 upstream.
Two people have reported (and mentioned numerous other reports on the
web) that VIA's VL817 USB-SATA bridge does not work with the uas
driver. Typical log messages are:
[ 3606.232149] sd 14:0:0:0: [sdg] tag#2 uas_zap_pending 0 uas-tag 1 inflight: CMD
[ 3606.232154] sd 14:0:0:0: [sdg] tag#2 CDB: Write(16) 8a 00 00 00 00 00 18 0c c9 80 00 00 00 80 00 00
[ 3606.306257] usb 4-4.4: reset SuperSpeed Plus Gen 2x1 USB device number 11 using xhci_hcd
[ 3606.328584] scsi host14: uas_eh_device_reset_handler success
Surprisingly, the devices do seem to work okay for some other people.
The cause of the differing behaviors is not known.
In the hope of getting the devices to work for the most users, even at
the possible cost of degraded performance for some, this patch adds an
unusual_devs entry for the VL817 to block it from binding to the uas
driver by default. Users will be able to override this entry by means
of a module parameter, if they want.
CC: <stable@vger.kernel.org>
Reported-by: DocMAX <mail@vacharakis.de>
Reported-and-tested-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/Ye8IsK2sjlEv1rqU@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8838b2af23 upstream.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.2.7.3 states that DC1 (XON) and DC3 (XOFF)
are the control characters defined in ISO/IEC 646. These shall be quoted if
seen in the data stream to avoid interpretation as flow control characters.
ISO/IEC 646 refers to the set of ISO standards described as the ISO
7-bit coded character set for information interchange. Its final version
is also known as ITU T.50.
See https://www.itu.int/rec/T-REC-T.50-199209-I/en
To abide the standard it is needed to quote DC1 and DC3 correctly if these
are seen as data bytes and not as control characters. The current
implementation already tries to enforce this but fails to catch all
defined cases. 3GPP 27.010 chapter 5.2.7.3 clearly states that the most
significant bit shall be ignored for DC1 and DC3 handling. The current
implementation handles only the case with the most significant bit set 0.
Cases in which DC1 and DC3 have the most significant bit set 1 are left
unhandled.
This patch fixes this by masking the data bytes with ISO_IEC_646_MASK (only
the 7 least significant bits set 1) before comparing them with XON
(a.k.a. DC1) and XOFF (a.k.a. DC3) when testing which byte values need
quotation via byte stuffing.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220120101857.2509-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d06b1cf282 upstream.
8250_of supports a reg-offset property which is intended to handle
cases where the device registers start at an offset inside the region
of memory allocated to the device. The Xilinx 16550 UART, for which this
support was initially added, requires this. However, the code did not
adjust the overall size of the mapped region accordingly, causing the
driver to request an area of memory past the end of the device's
allocation. For example, if the UART was allocated an address of
0xb0130000, size of 0x10000 and reg-offset of 0x1000 in the device
tree, the region of memory reserved was b0131000-b0140fff, which caused
the driver for the region starting at b0140000 to fail to probe.
Fix this by subtracting reg-offset from the mapped region size.
Fixes: b912b5e2cf ([POWERPC] Xilinx: of_serial support for Xilinx uart 16550.)
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220112194214.881844-1-robert.hancock@calian.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 38e0257e0e upstream.
The erratum 1418040 workaround enables CNTVCT_EL1 access trapping in EL0
when executing compat threads. The workaround is applied when switching
between tasks, but the need for the workaround could also change at an
exec(), when a non-compat task execs a compat binary or vice versa. Apply
the workaround in arch_setup_new_exec().
This leaves a small window of time between SET_PERSONALITY and
arch_setup_new_exec where preemption could occur and confuse the old
workaround logic that compares TIF_32BIT between prev and next. Instead, we
can just read cntkctl to make sure it's in the state that the next task
needs. I measured cntkctl read time to be about the same as a mov from a
general-purpose register on N1. Update the workaround logic to examine the
current value of cntkctl instead of the previous task's compat state.
Fixes: d49f7d7376 ("arm64: Move handling of erratum 1418040 into C code")
Cc: <stable@vger.kernel.org> # 5.9.x
Signed-off-by: D Scott Phillips <scott@os.amperecomputing.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211220234114.3926-1-scott@os.amperecomputing.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e3d26528e0 upstream.
While all userspace tried to limit commandstreams to 64K in size,
a bug in the Mesa driver lead to command streams of up to 128K
being submitted. Allow those to avoid breaking existing userspace.
Fixes: 6dfa2fab8d ("drm/etnaviv: limit submit sizes")
Cc: stable@vger.kernel.org
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 96fd2e89fb upstream.
The user recently report a perf issue in the ICX platform, when test by
perf event “uncore_imc_x/cas_count_write”,the write bandwidth is always
very small (only 0.38MB/s), it is caused by the wrong "umask" for the
"cas_count_write" event. When double-checking, find "cas_count_read"
also is wrong.
The public document for ICX uncore:
3rd Gen Intel® Xeon® Processor Scalable Family, Codename Ice Lake,Uncore
Performance Monitoring Reference Manual, Revision 1.00, May 2021
On 2.4.7, it defines Unit Masks for CAS_COUNT:
RD b00001111
WR b00110000
So corrected both "cas_count_read" and "cas_count_write" for ICX.
Old settings:
hswep_uncore_imc_events
INTEL_UNCORE_EVENT_DESC(cas_count_read, "event=0x04,umask=0x03")
INTEL_UNCORE_EVENT_DESC(cas_count_write, "event=0x04,umask=0x0c")
New settings:
snr_uncore_imc_events
INTEL_UNCORE_EVENT_DESC(cas_count_read, "event=0x04,umask=0x0f")
INTEL_UNCORE_EVENT_DESC(cas_count_write, "event=0x04,umask=0x30")
Fixes: 2b3b76b5ec ("perf/x86/intel/uncore: Add Ice Lake server uncore support")
Signed-off-by: Zhengjun Xing <zhengjun.xing@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20211223144826.841267-1-zhengjun.xing@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31c2558569 upstream.
Revert a completely broken check on an "invalid" RIP in SVM's workaround
for the DecodeAssists SMAP errata. kvm_vcpu_gfn_to_memslot() obviously
expects a gfn, i.e. operates in the guest physical address space, whereas
RIP is a virtual (not even linear) address. The "fix" worked for the
problematic KVM selftest because the test identity mapped RIP.
Fully revert the hack instead of trying to translate RIP to a GPA, as the
non-SEV case is now handled earlier, and KVM cannot access guest page
tables to translate RIP.
This reverts commit e72436bc3a.
Fixes: e72436bc3a ("KVM: SVM: avoid infinite loop on NPF from bad address")
Reported-by: Liam Merwick <liam.merwick@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Message-Id: <20220120010719.711476-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29044dae2e upstream.
Commit 49246466a9 ("fsnotify: move fsnotify_nameremove() hook out of
d_delete()") moved the fsnotify delete hook before d_delete() so fsnotify
will have access to a positive dentry.
This allowed a race where opening the deleted file via cached dentry
is now possible after receiving the IN_DELETE event.
To fix the regression in pseudo filesystems, convert d_delete() calls
to d_drop() (see commit 46c46f8df9 ("devpts_pty_kill(): don't bother
with d_delete()") and move the fsnotify hook after d_drop().
Add a missing fsnotify_unlink() hook in nfsdfs that was found during
the audit of fsnotify hooks in pseudo filesystems.
Note that the fsnotify hooks in simple_recursive_removal() follow
d_invalidate(), so they require no change.
Link: https://lore.kernel.org/r/20220120215305.282577-2-amir73il@gmail.com
Reported-by: Ivan Delalande <colona@arista.com>
Link: https://lore.kernel.org/linux-fsdevel/YeNyzoDM5hP5LtGW@visor/
Fixes: 49246466a9 ("fsnotify: move fsnotify_nameremove() hook out of d_delete()")
Cc: stable@vger.kernel.org # v5.3+
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4584a768f2 upstream.
Dan reported that he was unable to write to files that had been
asynchronously created when the client's OSD caps are restricted to a
particular namespace.
The issue is that the layout for the new inode is only partially being
filled. Ensure that we populate the pool_ns_data and pool_ns_len in the
iinfo before calling ceph_fill_inode.
Cc: stable@vger.kernel.org
URL: https://tracker.ceph.com/issues/54013
Fixes: 9a8d03ca2e ("ceph: attempt to do async create when possible")
Reported-by: Dan van der Ster <dan@vanderster.com>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c9d967b2ce upstream.
The buffer handling in pm_show_wakelocks() is tricky, and hopefully
correct. Ensure it really is correct by using sysfs_emit_at() which
handles all of the tricky string handling logic in a PAGE_SIZE buffer
for us automatically as this is a sysfs file being read from.
Reviewed-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f5390cd0b4 upstream.
Aditya reports [0] that his recent MacbookPro crashes in the firmware
when using the variable services at runtime. The culprit appears to be a
call to QueryVariableInfo(), which we did not use to call on Apple x86
machines in the past as they only upgraded from EFI v1.10 to EFI v2.40
firmware fairly recently, and QueryVariableInfo() (along with
UpdateCapsule() et al) was added in EFI v2.00.
The only runtime service introduced in EFI v2.00 that we actually use in
Linux is QueryVariableInfo(), as the capsule based ones are optional,
generally not used at runtime (all the LVFS/fwupd firmware update
infrastructure uses helper EFI programs that invoke capsule update at
boot time, not runtime), and not implemented by Apple machines in the
first place. QueryVariableInfo() is used to 'safely' set variables,
i.e., only when there is enough space. This prevents machines with buggy
firmwares from corrupting their NVRAMs when they run out of space.
Given that Apple machines have been using EFI v1.10 services only for
the longest time (the EFI v2.0 spec was released in 2006, and Linux
support for the newly introduced runtime services was added in 2011, but
the MacbookPro12,1 released in 2015 still claims to be EFI v1.10 only),
let's avoid the EFI v2.0 ones on all Apple x86 machines.
[0] https://lore.kernel.org/all/6D757C75-65B1-468B-842D-10410081A8E4@live.com/
Cc: <stable@vger.kernel.org>
Cc: Jeremy Kerr <jk@ozlabs.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Reported-by: Aditya Garg <gargaditya08@live.com>
Tested-by: Orlando Chamberlain <redecorating@protonmail.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Aditya Garg <gargaditya08@live.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215277
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7fc3b7c298 upstream.
udf_expand_file_adinicb() calls directly ->writepage to write data
expanded into a page. This however misses to setup inode for writeback
properly and so we can crash on inode->i_wb dereference when submitting
page for IO like:
BUG: kernel NULL pointer dereference, address: 0000000000000158
#PF: supervisor read access in kernel mode
...
<TASK>
__folio_start_writeback+0x2ac/0x350
__block_write_full_page+0x37d/0x490
udf_expand_file_adinicb+0x255/0x400 [udf]
udf_file_write_iter+0xbe/0x1b0 [udf]
new_sync_write+0x125/0x1c0
vfs_write+0x28e/0x400
Fix the problem by marking the page dirty and going through the standard
writeback path to write the page. Strictly speaking we would not even
have to write the page but we want to catch e.g. ENOSPC errors early.
Reported-by: butt3rflyh4ck <butterflyhuangxx@gmail.com>
CC: stable@vger.kernel.org
Fixes: 52ebea749a ("writeback: make backing_dev_info host cgroup-specific bdi_writebacks")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea8569194b upstream.
When we fail to expand inode from inline format to a normal format, we
restore inode to contain the original inline formatting but we forgot to
set i_lenAlloc back. The mismatch between i_lenAlloc and i_size was then
causing further problems such as warnings and lost data down the line.
Reported-by: butt3rflyh4ck <butterflyhuangxx@gmail.com>
CC: stable@vger.kernel.org
Fixes: 7e49b6f248 ("udf: Convert UDF to new truncate calling sequence")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c9db6679b upstream.
Suppose we have an environment with a number of non-NPIV FCP devices
(virtual HBAs / FCP devices / zfcp "adapter"s) sharing the same physical
FCP channel (HBA port) and its I_T nexus. Plus a number of storage target
ports zoned to such shared channel. Now one target port logs out of the
fabric causing an RSCN. Zfcp reacts with an ADISC ELS and subsequent port
recovery depending on the ADISC result. This happens on all such FCP
devices (in different Linux images) concurrently as they all receive a copy
of this RSCN. In the following we look at one of those FCP devices.
Requests other than FSF_QTCB_FCP_CMND can be slow until they get a
response.
Depending on which requests are affected by slow responses, there are
different recovery outcomes. Here we want to fix failed recoveries on port
or adapter level by avoiding recovery requests that can be slow.
We need the cached N_Port_ID for the remote port "link" test with ADISC.
Just before sending the ADISC, we now intentionally forget the old cached
N_Port_ID. The idea is that on receiving an RSCN for a port, we have to
assume that any cached information about this port is stale. This forces a
fresh new GID_PN [FC-GS] nameserver lookup on any subsequent recovery for
the same port. Since we typically can still communicate with the nameserver
efficiently, we now reach steady state quicker: Either the nameserver still
does not know about the port so we stop recovery, or the nameserver already
knows the port potentially with a new N_Port_ID and we can successfully and
quickly perform open port recovery. For the one case, where ADISC returns
successfully, we re-initialize port->d_id because that case does not
involve any port recovery.
This also solves a problem if the storage WWPN quickly logs into the fabric
again but with a different N_Port_ID. Such as on virtual WWPN takeover
during target NPIV failover.
[https://www.redbooks.ibm.com/abstracts/redp5477.html] In that case the
RSCN from the storage FDISC was ignored by zfcp and we could not
successfully recover the failover. On some later failback on the storage,
we could have been lucky if the virtual WWPN got the same old N_Port_ID
from the SAN switch as we still had cached. Then the related RSCN
triggered a successful port reopen recovery. However, there is no
guarantee to get the same N_Port_ID on NPIV FDISC.
Even though NPIV-enabled FCP devices are not affected by this problem, this
code change optimizes recovery time for gone remote ports as a side effect.
The timely drop of cached N_Port_IDs prevents unnecessary slow open port
attempts.
While the problem might have been in code before v2.6.32 commit
799b76d09a ("[SCSI] zfcp: Decouple gid_pn requests from erp") this fix
depends on the gid_pn_work introduced with that commit, so we mark it as
culprit to satisfy fix dependencies.
Note: Point-to-point remote port is already handled separately and gets its
N_Port_ID from the cached peer_d_id. So resetting port->d_id in general
does not affect PtP.
Link: https://lore.kernel.org/r/20220118165803.3667947-1-maier@linux.ibm.com
Fixes: 799b76d09a ("[SCSI] zfcp: Decouple gid_pn requests from erp")
Cc: <stable@vger.kernel.org> #2.6.32+
Suggested-by: Benjamin Block <bblock@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 663d34c8df upstream.
Currently if z/VM guest is allowed to retrieve hypervisor performance
data globally for all guests (privilege class B) the query is formed in a
way to include all guests but the group name is left empty. This leads to
that z/VM guests which have access control group set not being included
in the results (even local vm).
Change the query group identifier from empty to "any" to retrieve
information about all guests from any groups (or without a group set).
Cc: stable@vger.kernel.org
Fixes: 31cb4bd31a ("[S390] Hypervisor filesystem (s390_hypfs) for z/VM")
Reviewed-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f3b7e73b2c upstream.
If the size of the PLT entries generated by apply_rela() exceeds
64KiB, the first ones can no longer reach __jump_r1 with brc. Fix by
using brcl. An alternative solution is to add a __jump_r1 copy after
every 64KiB, however, the space savings are quite small and do not
justify the additional complexity.
Fixes: f19fbd5ed6 ("s390: introduce execute-trampolines for branches")
Cc: stable@vger.kernel.org
Reported-by: Andrea Righi <andrea.righi@canonical.com>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0735e639f1 upstream.
When resume from suspend, besides skipping PTP registration, it also
skipping PTP HW initialization. This could cause PTP clock not able to
operate properly when resume from suspend.
To fix this, only stmmac_ptp_register() is skipped when resume from
suspend.
Fixes: fe13192911 ("stmmac: Don't init ptp again when resume from suspend/hibernation")
Cc: <stable@vger.kernel.org> # 5.15.x
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2148927e6e upstream.
Commit ce0aa27ff3 ("sfp: add sfp-bus to bridge between network devices
and sfp cages") added code which finds SFP bus DT node even if the node
is disabled with status = "disabled". Because of this, when phylink is
created, it ends with non-null .sfp_bus member, even though the SFP
module is not probed (because the node is disabled).
We need to ignore disabled SFP bus node.
Fixes: ce0aa27ff3 ("sfp: add sfp-bus to bridge between network devices and sfp cages")
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org # 2203cbf2c8 ("net: sfp: move fwnode parsing into sfp-bus layer")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 899663be5e upstream.
Check for out-of-bound read was being performed at the end of while
num_reports loop, and would fill journal with false positives. Added
check to beginning of loop processing so that it doesn't get checked
after ptr has been advanced.
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: syphyr <syphyr@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removes all the common panel, dpi, and backlight configuration
from the individual vc4-kms-dpi-* files into vc4-kms-dpi.dtsi.
Creates a new vc4-kms-dpi-panel-overlay.dts for preconfigured
panels, with overrides to enable the different panel configurations.
Deprecates vc4-kms-dpi-at056tn53v1 as superceded by vc4-kms-dpi-panel.
vc4-kms-kippah-7inch not deprecated for now as it is likely to be
in wider use than at056tn53v1.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Both the base node and override set these parameters to 0,
so it made no difference. The base node should have been 1.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
HVS5 supports the 210101010 RGB[A|X] formats, but they were
missing from the DRM to HVS mapping list, so weren't available.
Add them in.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The default clock-stretch timeout is 35 mS, which works well for
SMBus, but there are some I2C devices which can stretch the clock even
longer. Rather than trying to prescribe a safe default for everyone,
allow the timeout to be configured.
Signed-off-by: Alex Crawford <raspberrypi/linux@code.acrawford.com>
commit a0f90c8815 upstream.
A failing usercopy of the fence_rep object will lead to a stale entry in
the file descriptor table as put_unused_fd() won't release it. This
enables userland to refer to a dangling 'file' object through that still
valid file descriptor, leading to all kinds of use-after-free
exploitation scenarios.
Fix this by deferring the call to fd_install() until after the usercopy
has succeeded.
Fixes: c906965dee ("drm/vmwgfx: Add export fence to file descriptor support")
Signed-off-by: Mathias Krause <minipli@grsecurity.net>
Signed-off-by: Zack Rusin <zackr@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68514dacf2 upstream.
A task can end up indefinitely sleeping in do_select() ->
poll_schedule_timeout() when the following race happens:
TASK1 (thread1) TASK2 TASK1 (thread2)
do_select()
setup poll_wqueues table
with 'fd'
write data to 'fd'
pollwake()
table->triggered = 1
closes 'fd' thread1 is
waiting for
poll_schedule_timeout()
- sees table->triggered
table->triggered = 0
return -EINTR
loop back in do_select()
But at this point when TASK1 loops back, the fdget() in the setup of
poll_wqueues fails. So now so we never find 'fd' is ready for reading
and sleep in poll_schedule_timeout() indefinitely.
Treat an fd that got closed as a fd on which some event happened. This
makes sure cannot block indefinitely in do_select().
Another option would be to return -EBADF in this case but that has a
potential of subtly breaking applications that excercise this behavior
and it happens to work for them. So returning fd as active seems like a
safer choice.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c8a4742c4 upstream.
When the TDP MMU is write-protection GFNs for page table protection (as
opposed to for dirty logging, or due to the HVA not being writable), it
checks if the SPTE is already write-protected and if so skips modifying
the SPTE and the TLB flush.
This behavior is incorrect because it fails to check if the SPTE
is write-protected for page table protection, i.e. fails to check
that MMU-writable is '0'. If the SPTE was write-protected for dirty
logging but not page table protection, the SPTE could locklessly be made
writable, and vCPUs could still be running with writable mappings cached
in their TLB.
Fix this by only skipping setting the SPTE if the SPTE is already
write-protected *and* MMU-writable is already clear. Technically,
checking only MMU-writable would suffice; a SPTE cannot be writable
without MMU-writable being set. But check both to be paranoid and
because it arguably yields more readable code.
Fixes: 46044f72c3 ("kvm: x86/mmu: Support write protection for nesting in tdp MMU")
Cc: stable@vger.kernel.org
Signed-off-by: David Matlack <dmatlack@google.com>
Message-Id: <20220113233020.3986005-2-dmatlack@google.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 614ddad17f upstream.
Currently, rcu_advance_cbs_nowake() checks that a grace period is in
progress, however, that grace period could end just after the check.
This commit rechecks that a grace period is still in progress while
holding the rcu_node structure's lock. The grace period cannot end while
the current CPU's rcu_node structure's ->lock is held, thus avoiding
false positives from the WARN_ON_ONCE().
As Daniel Vacek noted, it is not necessary for the rcu_node structure
to have a CPU that has not yet passed through its quiescent state.
Tested-by: Guillaume Morin <guillaume@morinfr.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 802d4d207e upstream
Commit 0a6890b9b4 ("bnx2x: Utilize FW 7.13.15.0.")
added validation for fastpath HSI versions for different
client init which was not meant for SR-IOV VF clients, which
resulted in firmware asserts when running VF clients with
different fastpath HSI version.
This patch along with the new firmware support in patch #1
fixes this behavior in order to not validate fastpath HSI
version for the VFs.
Fixes: 0a6890b9b4 ("bnx2x: Utilize FW 7.13.15.0.")
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7a49f7305 upstream
This new firmware addresses few important issues and enhancements
as mentioned below -
- Support direct invalidation of FP HSI Ver per function ID, required for
invalidating FP HSI Ver prior to each VF start, as there is no VF start
- BRB hardware block parity error detection support for the driver
- Fix the FCOE underrun flow
- Fix PSOD during FCoE BFS over the NIC ports after preboot driver
- Maintains backward compatibility
This patch incorporates this new firmware 7.13.21.0 in bnx2x driver.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7938d61591 upstream.
We need to flush TLBs before releasing backing store otherwise userspace
is able to encounter stale entries if a) it is not declaring access to
certain buffers and b) it races with the backing store release from a
such undeclared execution already executing on the GPU in parallel.
The approach taken is to mark any buffer objects which were ever bound
to the GPU and to trigger a serialized TLB flush when their backing
store is released.
Alternatively the flushing could be done on VMA unbind, at which point
we would be able to ascertain whether there is potential a parallel GPU
execution (which could race), but essentially it boils down to paying
the cost of TLB flushes potentially needlessly at VMA unbind time (when
the backing store is not known to be going away so not needed for
safety), versus potentially needlessly at backing store relase time
(since we at that point cannot tell whether there is anything executing
on the GPU which uses that object).
Thereforce simplicity of implementation has been chosen for now with
scope to benchmark and refine later as required.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reported-by: Sushma Venkatesh Reddy <sushma.venkatesh.reddy@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Dave Airlie <airlied@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09b8cd69ed upstream.
On an imx6dl-pico-pi board with a QCA9377 SDIO chip, simply trying to
connect via ssh to another machine causes:
[ 55.824159] ath10k_sdio mmc1:0001:1: failed to transmit packet, dropping: -12
[ 55.832169] ath10k_sdio mmc1:0001:1: failed to submit frame: -12
[ 55.838529] ath10k_sdio mmc1:0001:1: failed to push frame: -12
[ 55.905863] ath10k_sdio mmc1:0001:1: failed to transmit packet, dropping: -12
[ 55.913650] ath10k_sdio mmc1:0001:1: failed to submit frame: -12
[ 55.919887] ath10k_sdio mmc1:0001:1: failed to push frame: -12
, leading to an ssh connection failure.
One user inspected the size of frames on Wireshark and reported
the followig:
"I was able to narrow the issue down to the mtu. If I set the mtu for
the wlan0 device to 1486 instead of 1500, the issue does not happen.
The size of frames that I see on Wireshark is exactly 1500 after
setting it to 1486."
Clearing the HI_ACS_FLAGS_ALT_DATA_CREDIT_SIZE avoids the problem and
the ssh command works successfully after that.
Introduce a 'credit_size_workaround' field to ath10k_hw_params for
the QCA9377 SDIO, so that the HI_ACS_FLAGS_ALT_DATA_CREDIT_SIZE
is not set in this case.
Tested with QCA9377 SDIO with firmware WLAN.TF.1.1.1-00061-QCATFSWPZ-1.
Fixes: 2f918ea986 ("ath10k: enable alt data of TX path for sdio")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211124131047.713756-1-festevam@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87c01d57fa upstream.
hmm_range_fault() can be used instead of get_user_pages() for devices
which allow faulting however unlike get_user_pages() it will return an
error when used on a VM_MIXEDMAP range.
To make hmm_range_fault() more closely match get_user_pages() remove
this restriction. This requires dealing with the !ARCH_HAS_PTE_SPECIAL
case in hmm_vma_handle_pte(). Rather than replicating the logic of
vm_normal_page() call it directly and do a check for the zero pfn
similar to what get_user_pages() currently does.
Also add a test to hmm selftest to verify functionality.
Link: https://lkml.kernel.org/r/20211104012001.2555676-1-apopple@nvidia.com
Fixes: da4c3c735e ("mm/hmm/mirror: helper to snapshot CPU page table")
Signed-off-by: Alistair Popple <apopple@nvidia.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Zi Yan <ziy@nvidia.com>
Cc: Ralph Campbell <rcampbell@nvidia.com>
Cc: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 99218cbf81 upstream.
platform_get_irq() returns negative error number instead 0 on failure.
And the doc of platform_get_irq() provides a usage example:
int irq = platform_get_irq(pdev, 0);
if (irq < 0)
return irq;
Fix the check of return value to catch errors correctly.
Fixes: 1159788592 ("i825xx: Move the Intel 82586/82593/82596 based drivers")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d8adf5b92a upstream.
dtx_diff suggests to use <(...) syntax to pipe two inputs into it, but
this has never worked: The /proc/self/fds/... paths passed by the shell
will fail the `[ -f "${dtx}" ] && [ -r "${dtx}" ]` check in compile_to_dts,
but even with this check removed, the function cannot work: hexdump will
eat up the DTB magic, making the subsequent dtc call fail, as a pipe
cannot be rewound.
Simply remove this broken example, as there is already an alternative one
that works fine.
Fixes: 10eadc253d ("dtc: create tool to diff device trees")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220113081918.10387-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit baa59504c1 upstream.
Clang static analysis reports this issue
ocelot_flower.c:563:8: warning: 1st function call argument
is an uninitialized value
!is_zero_ether_addr(match.mask->dst)) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The variable match is used before it is set. So move the
block.
Fixes: 75944fda1d ("net: mscc: ocelot: offload ingress skbedit and vlan actions to VCAP IS1")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5765cee119 upstream.
Commit 7cfa9c92d0 ("net: sfp: avoid power switch on address-change
modules") unintetionally changed the semantics for high power modules
without the digital diagnostics monitoring. We repeatedly attempt to
read the power status from the non-existing 0xa2 address in a futile
hope this failure is temporary:
[ 8.856051] sfp sfp-eth3: module NTT 0000000000000000 rev 0000 sn 0000000000000000 dc 160408
[ 8.865843] mvpp2 f4000000.ethernet eth3: switched to inband/1000base-x link mode
[ 8.873469] sfp sfp-eth3: Failed to read EEPROM: -5
[ 8.983251] sfp sfp-eth3: Failed to read EEPROM: -5
[ 9.103250] sfp sfp-eth3: Failed to read EEPROM: -5
We previosuly assumed such modules were powered up in the correct mode,
continuing without further configuration as long as the required power
class was supported by the host.
Restore this behaviour, while preserving the intent of subsequent
patches to avoid the "Address Change Sequence not supported" warning
if we are not going to be accessing the DDM address.
Fixes: 7cfa9c92d0 ("net: sfp: avoid power switch on address-change modules")
Reported-by: 照山周一郎 <teruyama@springboard-inc.jp>
Tested-by: 照山周一郎 <teruyama@springboard-inc.jp>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 214b3369ab upstream.
Clang static analysis reports this problem
mtk_eth_soc.c:394:7: warning: Branch condition evaluates
to a garbage value
if (err)
^~~
err is not initialized and only conditionally set.
So intitialize err.
Fixes: 7e53837269 ("net: ethernet: mediatek: Re-add support SGMII")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9deb48b53e upstream.
The driver neglects to check the result of platform_get_irq_optional()'s
call and blithely passes the negative error codes to devm_request_irq()
(which takes *unsigned* IRQ #), causing it to fail with -EINVAL.
Stop calling devm_request_irq() with the invalid IRQ #s.
Fixes: 8562056f26 ("net: bcmgenet: request Wake-on-LAN interrupt")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb80445c43 upstream.
commit 56b765b79e ("htb: improved accuracy at high rates") broke
"overhead X", "linklayer atm" and "mpu X" attributes.
"overhead X" and "linklayer atm" have already been fixed. This restores
the "mpu X" handling, as might be used by DOCSIS or Ethernet shaping:
tc class add ... htb rate X overhead 4 mpu 64
The code being fixed is used by htb, tbf and act_police. Cake has its
own mpu handling. qdisc_calculate_pkt_len still uses the size table
containing values adjusted for mpu by user space.
iproute2 tc has always passed mpu into the kernel via a tc_ratespec
structure, but the kernel never directly acted on it, merely stored it
so that it could be read back by `tc class show`.
Rather, tc would generate length-to-time tables that included the mpu
(and linklayer) in their construction, and the kernel used those tables.
Since v3.7, the tables were no longer used. Along with "mpu", this also
broke "overhead" and "linklayer" which were fixed in 01cb71d2d4
("net_sched: restore "overhead xxx" handling", v3.10) and 8a8e3d84b1
("net_sched: restore "linklayer atm" handling", v3.11).
"overhead" was fixed by simply restoring use of tc_ratespec::overhead -
this had originally been used by the kernel but was initially omitted
from the new non-table-based calculations.
"linklayer" had been handled in the table like "mpu", but the mode was
not originally passed in tc_ratespec. The new implementation was made to
handle it by getting new versions of tc to pass the mode in an extended
tc_ratespec, and for older versions of tc the table contents were analysed
at load time to deduce linklayer.
As "mpu" has always been given to the kernel in tc_ratespec,
accompanying the mpu-based table, we can restore system functionality
with no userspace change by making the kernel act on the tc_ratespec
value.
Fixes: 56b765b79e ("htb: improved accuracy at high rates")
Signed-off-by: Kevin Bracey <kevin@bracey.fi>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: Vimalkumar <j.vimal@gmail.com>
Link: https://lore.kernel.org/r/20220112170210.1014351-1-kevin@bracey.fi
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e5bd03ae3 upstream.
In Linux bonding scenario, one packet is copied to several copies and sent
by all slave device of bond0 in mode 3(broadcast mode). The mode 3 xmit
function bond_xmit_broadcast() only ueses the last slave device's tx result
as the final result. In this case, if the last slave device is down, then
it always return NET_XMIT_DROP, even though the other slave devices xmit
success. It may cause the tx statistics error, and cause the application
(e.g. scp) consider the network is unreachable.
For example, use the following command to configure server A.
echo 3 > /sys/class/net/bond0/bonding/mode
ifconfig bond0 up
ifenslave bond0 eth0 eth1
ifconfig bond0 192.168.1.125
ifconfig eth0 up
ifconfig eth1 down
The slave device eth0 and eth1 are connected to server B(192.168.1.107).
Run the ping 192.168.1.107 -c 3 -i 0.2 command, the following information
is displayed.
PING 192.168.1.107 (192.168.1.107) 56(84) bytes of data.
64 bytes from 192.168.1.107: icmp_seq=1 ttl=64 time=0.077 ms
64 bytes from 192.168.1.107: icmp_seq=2 ttl=64 time=0.056 ms
64 bytes from 192.168.1.107: icmp_seq=3 ttl=64 time=0.051 ms
192.168.1.107 ping statistics
0 packets transmitted, 3 received
Actually, the slave device eth0 of the bond successfully sends three
ICMP packets, but the result shows that 0 packets are transmitted.
Also if we use scp command to get remote files, the command end with the
following printings.
ssh_exchange_identification: read: Connection timed out
So this patch modifies the bond_xmit_broadcast to return NET_XMIT_SUCCESS
if one slave device in the bond sends packets successfully. If all slave
devices send packets fail, the discarded packets stats is increased. The
skb is released when there is no slave device in the bond or the last slave
device is down.
Fixes: ae46f184bc ("bonding: propagate transmit status")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c41910f257 upstream.
These properties aren't documented nor implemented in the driver.
Drop them.
Fixes warnings as:
$ make dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/display/msm/gpu.yaml
...
arch/arm64/boot/dts/qcom/msm8996-mtp.dt.yaml: gpu@b00000: 'qcom,gpu-quirk-fault-detect-mask', 'qcom,gpu-quirk-two-pass-use-wfi' do not match any of the regexes: 'pinctrl-[0-9]+'
From schema: Documentation/devicetree/bindings/display/msm/gpu.yaml
...
Fixes: 69cc3114ab ("arm64: dts: Add Adreno GPU definitions")
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211030100413.28370-1-david@ixit.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9538f8270 upstream.
DEVLINK_CMD_HEALTH_REPORTER_DUMP_GET command doesn't have .doit callback
and has no use in internal_flags at all. Remove this misleading assignment.
Fixes: e44ef4e451 ("devlink: Hang reporter's dump method on a dumpit cb")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bccfb96b59 upstream.
tx_submit is supposed to push the current transaction descriptor to a
pending queue, waiting for issue_pending() to be called. issue_pending()
must start the transfer, not tx_submit(), thus remove
at_xdmac_start_xfer() from at_xdmac_tx_submit(). Clients of at_xdmac that
assume that tx_submit() starts the transfer must be updated and call
dma_async_issue_pending() if they miss to call it (one example is
atmel_serial).
As the at_xdmac_start_xfer() is now called only from
at_xdmac_advance_work() when !at_xdmac_chan_is_enabled(), the
at_xdmac_chan_is_enabled() check is no longer needed in
at_xdmac_start_xfer(), thus remove it.
Fixes: e1f7c9eee7 ("dmaengine: at_xdmac: creation of the atmel eXtended DMA Controller driver")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20211215110115.191749-2-tudor.ambarus@microchip.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a915deaa9a upstream.
Mask the ECN bits before calling ip_route_output_ports(). The tos
variable might be passed directly from an IPv4 header, so it may have
the last ECN bit set. This interferes with the route lookup process as
ip_route_output_key_hash() interpretes this bit specially (to restrict
the route scope).
Found by code inspection, compile tested only.
Fixes: 804c2f3e36 ("libcxgb,iw_cxgb4,cxgbit: add cxgb_find_route()")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7716b3185 upstream.
Mask the ECN bits before initialising ->flowi4_tos. The tunnel key may
have the last ECN bit set, which will interfere with the route lookup
process as ip_route_output_key_hash() interpretes this bit specially
(to restrict the route scope).
Found by code inspection, compile tested only.
Fixes: 962924fa2b ("ip_gre: Refactor collect metatdata mode tunnel xmit to ip_md_tunnel_xmit")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23e7b1bfed upstream.
Similar to commit 94e2238969 ("xfrm4: strip ECN bits from tos field"),
clear the ECN bits from iph->tos when setting ->flowi4_tos.
This ensures that the last bit of ->flowi4_tos is cleared, so
ip_route_output_key_hash() isn't going to restrict the scope of the
route lookup.
Use ~INET_ECN_MASK instead of IPTOS_RT_MASK, because we have no reason
to clear the high order bits.
Found by code inspection, compile tested only.
Fixes: 4da3089f2b ("[IPSEC]: Use TOS when doing tunnel lookups")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2836615aa2 upstream.
When under stress, cleanup_net() can have to dismantle
netns in big numbers. ops_exit_list() currently calls
many helpers [1] that have no schedule point, and we can
end up with soft lockups, particularly on hosts
with many cpus.
Even for moderate amount of netns processed by cleanup_net()
this patch avoids latency spikes.
[1] Some of these helpers like fib_sync_up() and fib_sync_down_dev()
are very slow because net/ipv4/fib_semantics.c uses host-wide hash tables,
and ifindex is used as the only input of two hash functions.
ifindexes tend to be the same for all netns (lo.ifindex==1 per instance)
This will be fixed in a separate patch.
Fixes: 72ad937abd ("net: Add support for batching network namespace cleanups")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 91341fa000 upstream.
Both fields can be read/written without synchronization,
add proper accessors and documentation.
Fixes: d5dd88794a ("inet: fix various use-after-free in defrags units")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b5a42d9c8 upstream.
In the function bacct_add_task the code reading task->exit_code was
introduced in commit f3cef7a994 ("[PATCH] csa: basic accounting over
taskstats"), and it is not entirely clear what the taskstats interface
is trying to return as only returning the exit_code of the first task
in a process doesn't make a lot of sense.
As best as I can figure the intent is to return task->exit_code after
a task exits. The field is returned with per task fields, so the
exit_code of the entire process is not wanted. Only the value of the
first task is returned so this is not a useful way to get the per task
ptrace stop code. The ordinary case of returning this value is
returning after a task exits, which also precludes use for getting
a ptrace value.
It is common to for the first task of a process to also be the last
task of a process so this field may have done something reasonable by
accident in testing.
Make ac_exitcode a reliable per task value by always returning it for
every exited task.
Setting ac_exitcode in a sensible mannter makes it possible to continue
to provide this value going forward.
Cc: Balbir Singh <bsingharora@gmail.com>
Fixes: f3cef7a994 ("[PATCH] csa: basic accounting over taskstats")
Link: https://lkml.kernel.org/r/20220103213312.9144-5-ebiederm@xmission.com
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1861ba626a upstream.
A recently added error path does not mark ring unused when exiting on
OOM, which will lead to BUG on the next entry in debug builds.
TODO: refactor code so we have START_USE and END_USE in the same function.
Fixes: fc6d70f40b ("virtio_ring: check desc == NULL when using indirect with packed")
Cc: "Xuan Zhuo" <xuanzhuo@linux.alibaba.com>
Cc: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 34127b3632 upstream.
With the latest stable kernel versions the rtc on the PXA based
Zaurus does not work, when booting I see the following kernel messages:
pxa-rtc pxa-rtc: failed to find rtc clock source
pxa-rtc pxa-rtc: Unable to init SA1100 RTC sub-device
pxa-rtc: probe of pxa-rtc failed with error -2
hctosys: unable to open rtc device (rtc0)
I think this is because commit f2997775b1 ("rtc: sa1100: fix possible
race condition") moved the allocation of the rtc_device struct out of
sa1100_rtc_init and into sa1100_rtc_probe. This means that pxa_rtc_probe
also needs to do allocation for the rtc_device struct, otherwise
sa1100_rtc_init will try to dereference a null pointer. This patch adds
that allocation by copying how sa1100_rtc_probe in
drivers/rtc/rtc-sa1100.c does it; after the IRQs are set up a managed
rtc_device is allocated.
I've tested this patch with `qemu-system-arm -machine akita` and with a
real Zaurus SL-C1000 applied to 4.19, 5.4, and 5.10.
Signed-off-by: Laurence de Bruxelles <lfdebrux@gmail.com>
Fixes: f2997775b1 ("rtc: sa1100: fix possible race condition")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220101154149.12026-1-lfdebrux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3fe6acd4dc upstream.
Unfortunately details of USB HID transport bled into HID core and
handling of numbered/unnumbered reports is quite a mess, with
hid_report_len() calculating the length according to USB rules,
and hid_hw_raw_request() adding report ID to the buffer for both
numbered and unnumbered reports.
Untangling it all requres a lot of changes in HID, so for now let's
handle this in the driver.
[jkosina@suse.cz: microoptimize field->report->id to report->id]
Fixes: 14c9c014ba ("HID: add vivaldi HID driver")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Stephen Boyd <swboyd@chromium.org> # CoachZ
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2d19c3fd80 upstream.
With previous changes to make the driver handle the TX ring size more
correctly, the default TX ring size of 64 appears to significantly
bottleneck TX performance to around 600 Mbps on a 1 Gbps link on ZynqMP.
Increasing this to 128 seems to bring performance up to near line rate and
shouldn't cause excess bufferbloat (this driver doesn't yet support modern
byte-based queue management).
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb193e3db8 upstream.
Network driver documentation indicates we should be avoiding returning
NETDEV_TX_BUSY from ndo_start_xmit in normal cases, since it requires
the packets to be requeued. Instead the queue should be stopped after
a packet is added to the TX ring when there may not be enough room for an
additional one. Also, when TX ring entries are completed, we should only
wake the queue if we know there is room for another full maximally
fragmented packet.
Print a warning if there is insufficient space at the start of start_xmit,
since this should no longer happen.
Combined with increasing the default TX ring size (in a subsequent
patch), this appears to recover the TX performance lost by previous changes
to actually manage the TX ring state properly.
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aba57a823d upstream.
The check for the number of available TX ring slots was off by 1 since a
slot is required for the skb header as well as each fragment. This could
result in overwriting a TX ring slot that was still in use.
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 996defd7f8 upstream.
The check for whether a TX ring slot was available was incorrect,
since a slot which had been loaded with transmit data but the device had
not started transmitting would be treated as available, potentially
causing non-transmitted slots to be overwritten. The control field in
the descriptor should be checked, rather than the status field (which may
only be updated when the device completes the entry).
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70f5817ded upstream.
The driver will not work properly if the TX ring size is set to below
MAX_SKB_FRAGS + 1 since it needs to hold at least one full maximally
fragmented packet in the TX ring. Limit setting the ring size to below
this value.
Fixes: 8b09ca823f ("net: axienet: Make RX/TX ring sizes configurable")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95978df6fa upstream.
This driver was missing some required memory barriers:
Use dma_rmb to ensure we see all updates to the descriptor after we see
that an entry has been completed.
Use wmb and rmb to avoid stale descriptor status between the TX path and
TX complete IRQ path.
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04cc2da396 upstream.
In some cases where the Xilinx Ethernet core was used in 1000Base-X or
SGMII modes, which use the internal PCS/PMA PHY, and the MGT
transceiver clock source for the PCS was not running at the time the
FPGA logic was loaded, the core would come up in a state where the
PCS could not be found on the MDIO bus. To fix this, the Ethernet core
(including the PCS) should be reset after enabling the clocks, prior to
attempting to access the PCS using of_mdio_find_device.
Fixes: 1a02556086 (net: axienet: Properly handle PCS/PMA PHY for 1000BaseX mode)
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b400c2f4f4 upstream.
When resetting the device, wait for the PhyRstCmplt bit to be set
in the interrupt status register before continuing initialization, to
ensure that the core is actually ready. When using an external PHY, this
also ensures we do not start trying to access the PHY while it is still
in reset. The PHY reset is initiated by the core reset which is
triggered just above, but remains asserted for 5ms after the core is
reset according to the documentation.
The MgtRdy bit could also be waited for, but unfortunately when using
7-series devices, the bit does not appear to work as documented (it
seems to behave as some sort of link state indication and not just an
indication the transceiver is ready) so it can't really be relied on for
this purpose.
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e5644b1ba upstream.
The previous timeout of 1ms was too short to handle some cases where the
core is reset just after the input clocks were started, which will
be introduced in an upcoming patch. Increase the timeout to 50ms. Also
simplify the reset timeout checking to use read_poll_timeout.
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56d99e81ec upstream.
A hung_task is observed when removing SMC-R devices. Suppose that
a link group has two active links(lnk_A, lnk_B) associated with two
different SMC-R devices(dev_A, dev_B). When dev_A is removed, the
link group will be removed from smc_lgr_list and added into
lgr_linkdown_list. lnk_A will be cleared and smcibdev(A)->lnk_cnt
will reach to zero. However, when dev_B is removed then, the link
group can't be found in smc_lgr_list and lnk_B won't be cleared,
making smcibdev->lnk_cnt never reaches zero, which causes a hung_task.
This patch fixes this issue by restoring the implementation of
smc_smcr_terminate_all() to what it was before commit 349d43127d
("net/smc: fix kernel panic caused by race of smc_sock"). The original
implementation also satisfies the intention that make sure QP destroy
earlier than CQ destroy because we will always wait for smcibdev->lnk_cnt
reaches zero, which guarantees QP has been destroyed.
Fixes: 349d43127d ("net/smc: fix kernel panic caused by race of smc_sock")
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 489a71964f upstream.
We don't want vendors to be enabling this part of the clk code and
shipping it to customers. Exposing the ability to change clk frequencies
and parents via debugfs is potentially damaging to the system if folks
don't know what they're doing. Emit a strong warning so that the message
is clear: don't enable this outside of development systems.
Fixes: 37215da555 ("clk: Add support for setting clk_rate via debugfs")
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20211210014237.2130300-1-sboyd@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7377e85396 upstream.
There is a potential deadlock between writeback process and a process
performing write_begin() or write_cache_pages() while trying to write
same compress file, but not compressable, as below:
[Process A] - doing checkpoint
[Process B] [Process C]
f2fs_write_cache_pages()
- lock_page() [all pages in cluster, 0-31]
- f2fs_write_multi_pages()
- f2fs_write_raw_pages()
- f2fs_write_single_data_page()
- f2fs_do_write_data_page()
- return -EAGAIN [f2fs_trylock_op() failed]
- unlock_page(page) [e.g., page 0]
- generic_perform_write()
- f2fs_write_begin()
- f2fs_prepare_compress_overwrite()
- prepare_compress_overwrite()
- lock_page() [e.g., page 0]
- lock_page() [e.g., page 1]
- lock_page(page) [e.g., page 0]
Since there is no compress process, it is no longer necessary to hold
locks on every pages in cluster within f2fs_write_raw_pages().
This patch changes f2fs_write_raw_pages() to release all locks first
and then perform write same as the non-compress file in
f2fs_write_cache_pages().
Fixes: 4c8ff7095b ("f2fs: support data compression")
Signed-off-by: Hyeong-Jun Kim <hj514.kim@samsung.com>
Signed-off-by: Sungjong Seo <sj1557.seo@samsung.com>
Signed-off-by: Youngjin Gil <youngjin.gil@samsung.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d24846a424 upstream.
kobject_init_and_add() takes reference even when it fails.
According to the doc of kobject_init_and_add()：
If this function returns an error, kobject_put() must be called to
properly clean up the memory associated with the object.
Fix memory leak by calling kobject_put().
Fixes: 73f368cf67 ("Kobject: change drivers/parisc/pdc_stable.c to use kobject_init_and_add")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f7c239c78 upstream.
As reported by sparse: In the remove path, the driver would attempt to
unmap its own priv pointer - instead of the io memory that it mapped
in probe.
Fixes: 9f35a7342c ("net/fsl: introduce Freescale 10G MDIO driver")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6198c72201 upstream.
Once an MDIO read transaction is initiated, we must read back the data
register within 16 MDC cycles after the transaction completes. Outside
of this window, reads may return corrupt data.
Therefore, disable local interrupts in the critical section, to
maximize the probability that we can satisfy this requirement.
Fixes: d55ad2967d ("powerpc/mpc85xx: Create dts components for the FSL QorIQ DPAA FMan")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d07418afea upstream.
net/ipv4/fib_semantics.c uses an hash table of 256 slots,
keyed by device ifindexes: fib_info_devhash[DEVINDEX_HASHSIZE]
Problem is that with network namespaces, devices tend
to use the same ifindex.
lo device for instance has a fixed ifindex of one,
for all network namespaces.
This means that hosts with thousands of netns spend
a lot of time looking at some hash buckets with thousands
of elements, notably at netns dismantle.
Simply add a per netns perturbation (net_hash_mix())
to spread elements more uniformely.
Also change fib_devindex_hashfn() to use more entropy.
Fixes: aa79e66eee ("net: Make ifindex generation per-net namespace")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0a6e6b3c7d upstream.
In the past, free_fib_info() was supposed to be called
under RTNL protection.
This eventually was no longer the case.
Instead of enforcing RTNL it seems we simply can
move fib_info_cnt changes to occur when fib_info_lock
is held.
v2: David Laight suggested to update fib_info_cnt
only when an entry is added/deleted to/from the hash table,
as fib_info_cnt is used to make sure hash table size
is optimal.
BUG: KCSAN: data-race in fib_create_info / free_fib_info
write to 0xffffffff86e243a0 of 4 bytes by task 26429 on cpu 0:
fib_create_info+0xe78/0x3440 net/ipv4/fib_semantics.c:1428
fib_table_insert+0x148/0x10c0 net/ipv4/fib_trie.c:1224
fib_magic+0x195/0x1e0 net/ipv4/fib_frontend.c:1087
fib_add_ifaddr+0xd0/0x2e0 net/ipv4/fib_frontend.c:1109
fib_netdev_event+0x178/0x510 net/ipv4/fib_frontend.c:1466
notifier_call_chain kernel/notifier.c:83 [inline]
raw_notifier_call_chain+0x53/0xb0 kernel/notifier.c:391
__dev_notify_flags+0x1d3/0x3b0
dev_change_flags+0xa2/0xc0 net/core/dev.c:8872
do_setlink+0x810/0x2410 net/core/rtnetlink.c:2719
rtnl_group_changelink net/core/rtnetlink.c:3242 [inline]
__rtnl_newlink net/core/rtnetlink.c:3396 [inline]
rtnl_newlink+0xb10/0x13b0 net/core/rtnetlink.c:3506
rtnetlink_rcv_msg+0x745/0x7e0 net/core/rtnetlink.c:5571
netlink_rcv_skb+0x14e/0x250 net/netlink/af_netlink.c:2496
rtnetlink_rcv+0x18/0x20 net/core/rtnetlink.c:5589
netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
netlink_unicast+0x5fc/0x6c0 net/netlink/af_netlink.c:1345
netlink_sendmsg+0x726/0x840 net/netlink/af_netlink.c:1921
sock_sendmsg_nosec net/socket.c:704 [inline]
sock_sendmsg net/socket.c:724 [inline]
____sys_sendmsg+0x39a/0x510 net/socket.c:2409
___sys_sendmsg net/socket.c:2463 [inline]
__sys_sendmsg+0x195/0x230 net/socket.c:2492
__do_sys_sendmsg net/socket.c:2501 [inline]
__se_sys_sendmsg net/socket.c:2499 [inline]
__x64_sys_sendmsg+0x42/0x50 net/socket.c:2499
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffffffff86e243a0 of 4 bytes by task 31505 on cpu 1:
free_fib_info+0x35/0x80 net/ipv4/fib_semantics.c:252
fib_info_put include/net/ip_fib.h:575 [inline]
nsim_fib4_rt_destroy drivers/net/netdevsim/fib.c:294 [inline]
nsim_fib4_rt_replace drivers/net/netdevsim/fib.c:403 [inline]
nsim_fib4_rt_insert drivers/net/netdevsim/fib.c:431 [inline]
nsim_fib4_event drivers/net/netdevsim/fib.c:461 [inline]
nsim_fib_event drivers/net/netdevsim/fib.c:881 [inline]
nsim_fib_event_work+0x15ca/0x2cf0 drivers/net/netdevsim/fib.c:1477
process_one_work+0x3fc/0x980 kernel/workqueue.c:2298
process_scheduled_works kernel/workqueue.c:2361 [inline]
worker_thread+0x7df/0xa70 kernel/workqueue.c:2447
kthread+0x2c7/0x2e0 kernel/kthread.c:327
ret_from_fork+0x1f/0x30
value changed: 0x00000d2d -> 0x00000d2e
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 31505 Comm: kworker/1:21 Not tainted 5.16.0-rc6-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: events nsim_fib_event_work
Fixes: 48bb9eb47b ("netdevsim: fib: Add dummy implementation for FIB offload")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: Ido Schimmel <idosch@mellanox.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d375d610f upstream.
This block is used in (at least) T1024 and T1040, including their
variants like T1023 etc.
Fixes: d55ad2967d ("powerpc/mpc85xx: Create dts components for the FSL QorIQ DPAA FMan")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e89257e28e upstream.
Clang warns:
arch/powerpc/platforms/cell/pervasive.c:81:2: error: unannotated fall-through between switch labels
case SRR1_WAKEEE:
^
arch/powerpc/platforms/cell/pervasive.c:81:2: note: insert 'break;' to avoid fall-through
case SRR1_WAKEEE:
^
break;
1 error generated.
Clang is more pedantic than GCC, which does not warn when failing
through to a case that is just break or return. Clang's version is more
in line with the kernel's own stance in deprecated.rst. Add athe missing
break to silence the warning.
Fixes: 6e83985b0f ("powerpc/cbe: Do not process external or decremeter interrupts from sreset")
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211207110228.698956-1-anders.roxell@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f6626b0e1 upstream.
This reverts commit 410bd754cd.
The reverted commit had added a retry mechanism to the command entry
index allocation. The previous patch ensures that there is a free
command entry index once the command work handler holds the command
semaphore. Thus the retry mechanism is not needed.
Fixes: 410bd754cd ("net/mlx5: Add retry mechanism to the command entry index allocation")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f16a491c65 upstream.
10bbffa3e8 attempted to fix the use of rotation duration as
advertising duration but it didn't change the if condition which still
uses the duration instead of the timeout.
Fixes: 10bbffa3e8 ("Bluetooth: Fix using advertising instance duration as timeout")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b0ac702f33 upstream.
Adjust the path of the ABI files for firewire.rst to prevent a
documentation build error. Prevents this problem:
Sphinx parallel build error:
docutils.utils.SystemMessage: Documentation/driver-api/firewire.rst:22: (SEVERE/4) Problems with "include" directive path:
InputError: [Errno 2] No such file or directory: '../Documentation/driver-api/ABI/stable/firewire-cdev'.
Fixes: 2f4830ef96 ("FireWire: add driver-api Introduction section")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Akira Yokosawa <akiyks@gmail.com>
Link: https://lore.kernel.org/r/20220119033905.4779-1-rdunlap@infradead.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 82ca67321f upstream.
The config RANDOMIZE_SLAB does not exist, the authors probably intended to
refer to the config RANDOMIZE_BASE, which provides kernel address-space
randomization. They probably just confused SLAB with BASE (these two
four-letter words coincidentally share three common letters), as they also
point out the config SLAB_FREELIST_RANDOM as further randomization within
the same sentence.
Fix the reference of the config for kernel address-space randomization to
the config that provides that.
Fixes: 6e88559470 ("Documentation: Add section about CPU vulnerabilities for Spectre")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20211230171940.27558-1-lukas.bulwahn@gmail.com
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a111749522 upstream.
The data node reference documentation was missing a package that must
contain the property values, instead property name and multiple values
being present in a single package. This is not aligned with the _DSD
spec.
Fix it by adding the package for the values.
Also add the missing "reg" properties to two numbered nodes.
Fixes: b10134a364 ("ACPI: property: Document hierarchical data extension references")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 20b0dfa86b upstream.
Similarly to what we encountered with the detect hook with DRM, nothing
actually prevents any of the CEC callback from being run while the HDMI
output is disabled.
However, this is an issue since any register access to the controller
when it's powered down will result in a silent hang.
Let's make sure we run the runtime_pm hooks when the CEC adapter is
opened and closed by the userspace to avoid that issue.
Fixes: 15b4511a4a ("drm/vc4: add HDMI CEC support")
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210819135931.895976-6-maxime@cerno.tech
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 549cc89cd0 upstream.
PHTW register is selected based on default bit rate from Table[1].
for the bit rates less than or equal to 250. Currently first
value of default bit rate which is greater than or equal to
the caculated mbps is selected. This selection can be further
improved by selecting the default bit rate which is nearest to
the calculated value.
[1] specs r19uh0105ej0200-r-car-3rd-generation.pdf [Table 25.12]
Fixes: 769afd212b ("media: rcar-csi2: add Renesas R-Car MIPI CSI-2 receiver driver")
Signed-off-by: Suresh Udipi <sudipi@jp.adit-jv.com>
Signed-off-by: Michael Rodin <mrodin@de.adit-jv.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d185a3466f upstream.
The help text for GOOGLE_FIRMWARE states that it should only be
enabled when building a kernel for Google's own servers. However,
many of the drivers dependent on it are also useful on Chromebooks or
on any platform using coreboot.
Update the help text to reflect this double duty.
Fixes: d384d6f43d ("firmware: google memconsole: Add coreboot support")
Reviewed-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Link: https://lore.kernel.org/r/20180618225540.GD14131@decadent.org.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d05b811b5 upstream.
The cells_name field of of_phandle_iterator might be NULL. Use the
phandle name instead. With this change instead of:
OF: /soc/pinctrl@1000000: (null) = 3 found 2
We get:
OF: /soc/pinctrl@1000000: phandle pinctrl@1000000 needs 3, found 2
Which is a more helpful messages making DT debugging easier.
In this particular example the phandle name looks like duplicate of the
same node name. But note that the first node is the parent node
(it->parent), while the second is the phandle target (it->node). They
happen to be the same in the case that triggered this improvement. See
commit 72cb4c48a4 ("arm64: dts: qcom: ipq6018: Fix gpio-ranges
property").
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/f6a68e0088a552ea9dfd4d8e3b5b586d92594738.1640881913.git.baruch@tkos.co.il
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6eeaf88fd5 upstream.
We probably want to remove the indirect block to extents migration
feature after a deprecation window, but until then, let's fix a
potential data loss problem caused by the fact that we put the
tmp_inode on the orphan list. In the unlikely case where we crash and
do a journal recovery, the data blocks belonging to the inode being
migrated are also represented in the tmp_inode on the orphan list ---
and so its data blocks will get marked unallocated, and available for
reuse.
Instead, stop putting the tmp_inode on the oprhan list. So in the
case where we crash while migrating the inode, we'll leak an inode,
which is not a disaster. It will be easily fixed the next time we run
fsck, and it's better than potentially having blocks getting claimed
by two different files, and losing data as a result.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Lukas Czerner <lczerner@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b5b5a62b9 upstream.
For now ,we use ext4_punch_hole() during fast commit replay delete range
procedure. But it will be affected by inode->i_size, which may not
correct during fast commit replay procedure. The following test will
failed.
-create & write foo (len 1000K)
-falloc FALLOC_FL_ZERO_RANGE foo (range 400K - 600K)
-create & fsync bar
-falloc FALLOC_FL_PUNCH_HOLE foo (range 300K-500K)
-fsync foo
-crash before a full commit
After the fast_commit reply procedure, the range 400K-500K will not be
removed. Because in this case, when calling ext4_punch_hole() the
inode->i_size is 0, and it just retruns with doing nothing.
Change to use ext4_ext_remove_space() instead of ext4_punch_hole()
to remove blocks of inode directly.
Signed-off-by: Xin Yin <yinxin.x@bytedance.com>
Reviewed-by: Harshad Shirwadkar <harshadshirwadkar@gmail.com>
Link: https://lore.kernel.org/r/20211223032337.5198-2-yinxin.x@bytedance.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c80fb312d upstream.
We found on older kernel (3.10) that in the scenario of insufficient
disk space, system may trigger an ABBA deadlock problem, it seems that
this problem still exists in latest kernel, try to fix it here. The
main process triggered by this problem is that task A occupies the PA
and waits for the jbd2 transaction finish, the jbd2 transaction waits
for the completion of task B's IO (plug_list), but task B waits for
the release of PA by task A to finish discard, which indirectly forms
an ABBA deadlock. The related calltrace is as follows:
Task A
vfs_write
ext4_mb_new_blocks()
ext4_mb_mark_diskspace_used() JBD2
jbd2_journal_get_write_access() -> jbd2_journal_commit_transaction()
->schedule() filemap_fdatawait()
| |
| Task B |
| do_unlinkat() |
| ext4_evict_inode() |
| jbd2_journal_begin_ordered_truncate() |
| filemap_fdatawrite_range() |
| ext4_mb_new_blocks() |
-ext4_mb_discard_group_preallocations() <-----
Here, try to cancel ext4_mb_discard_group_preallocations() internal
retry due to PA busy, and do a limited number of retries inside
ext4_mb_discard_preallocations(), which can circumvent the above
problems, but also has some advantages:
1. Since the PA is in a busy state, if other groups have free PAs,
keeping the current PA may help to reduce fragmentation.
2. Continue to traverse forward instead of waiting for the current
group PA to be released. In most scenarios, the PA discard time
can be reduced.
However, in the case of smaller free space, if only a few groups have
space, then due to multiple traversals of the group, it may increase
CPU overhead. But in contrast, I feel that the overall benefit is
better than the cost.
Signed-off-by: Chunguang Xu <brookxu@tencent.com>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/1637630277-23496-1-git-send-email-brookxu.cn@gmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 15fc69bbbb upstream.
When we hit an error when enabling quotas and setting inode flags, we do
not properly shutdown quota subsystem despite returning error from
Q_QUOTAON quotactl. This can lead to some odd situations like kernel
using quota file while it is still writeable for userspace. Make sure we
properly cleanup the quota subsystem in case of error.
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: stable@kernel.org
Link: https://lore.kernel.org/r/20211007155336.12493-2-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2f822635d upstream.
If we extended the size of a swapfile after its header was created (by the
mkswap utility) and then try to activate it, we will map the entire file
when activating the swap file, instead of limiting to the max size defined
in the swap file's header.
Currently test case generic/643 from fstests fails because we do not
respect that size limit defined in the swap file's header.
So fix this by not mapping file ranges beyond the max size defined in the
swap header.
This is the same type of bug that iomap used to have, and was fixed in
commit 36ca7943ac ("mm/swap: consider max pages in
iomap_swapfile_add_extent").
Fixes: ed46ff3d42 ("Btrfs: support swap files")
CC: stable@vger.kernel.org # 5.4+
Reviewed-and-tested-by: Josef Bacik <josef@toxicpanda.com
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 120de408e4 upstream.
Now that we clear the extent buffer uptodate if we fail to write it out
we need to check to see if our root node is uptodate before we search
down it. Otherwise we could return stale data (or potentially corrupt
data that was caught by the write verification step) and think that the
path is OK to search down.
CC: stable@vger.kernel.org # 5.4+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 232796df8c upstream.
When enabling quotas, we attempt to commit a transaction while holding the
mutex fs_info->qgroup_ioctl_lock. This can result on a deadlock with other
quota operations such as:
- qgroup creation and deletion, ioctl BTRFS_IOC_QGROUP_CREATE;
- adding and removing qgroup relations, ioctl BTRFS_IOC_QGROUP_ASSIGN.
This is because these operations join a transaction and after that they
attempt to lock the mutex fs_info->qgroup_ioctl_lock. Acquiring that mutex
after joining or starting a transaction is a pattern followed everywhere
in qgroups, so the quota enablement operation is the one at fault here,
and should not commit a transaction while holding that mutex.
Fix this by making the transaction commit while not holding the mutex.
We are safe from two concurrent tasks trying to enable quotas because
we are serialized by the rw semaphore fs_info->subvol_sem at
btrfs_ioctl_quota_ctl(), which is the only call site for enabling
quotas.
When this deadlock happens, it produces a trace like the following:
INFO: task syz-executor:25604 blocked for more than 143 seconds.
Not tainted 5.15.0-rc6 #4
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:syz-executor state:D stack:24800 pid:25604 ppid: 24873 flags:0x00004004
Call Trace:
context_switch kernel/sched/core.c:4940 [inline]
__schedule+0xcd9/0x2530 kernel/sched/core.c:6287
schedule+0xd3/0x270 kernel/sched/core.c:6366
btrfs_commit_transaction+0x994/0x2e90 fs/btrfs/transaction.c:2201
btrfs_quota_enable+0x95c/0x1790 fs/btrfs/qgroup.c:1120
btrfs_ioctl_quota_ctl fs/btrfs/ioctl.c:4229 [inline]
btrfs_ioctl+0x637e/0x7b70 fs/btrfs/ioctl.c:5010
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:874 [inline]
__se_sys_ioctl fs/ioctl.c:860 [inline]
__x64_sys_ioctl+0x193/0x200 fs/ioctl.c:860
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f86920b2c4d
RSP: 002b:00007f868f61ac58 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 00007f86921d90a0 RCX: 00007f86920b2c4d
RDX: 0000000020005e40 RSI: 00000000c0109428 RDI: 0000000000000008
RBP: 00007f869212bd80 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f86921d90a0
R13: 00007fff6d233e4f R14: 00007fff6d233ff0 R15: 00007f868f61adc0
INFO: task syz-executor:25628 blocked for more than 143 seconds.
Not tainted 5.15.0-rc6 #4
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:syz-executor state:D stack:29080 pid:25628 ppid: 24873 flags:0x00004004
Call Trace:
context_switch kernel/sched/core.c:4940 [inline]
__schedule+0xcd9/0x2530 kernel/sched/core.c:6287
schedule+0xd3/0x270 kernel/sched/core.c:6366
schedule_preempt_disabled+0xf/0x20 kernel/sched/core.c:6425
__mutex_lock_common kernel/locking/mutex.c:669 [inline]
__mutex_lock+0xc96/0x1680 kernel/locking/mutex.c:729
btrfs_remove_qgroup+0xb7/0x7d0 fs/btrfs/qgroup.c:1548
btrfs_ioctl_qgroup_create fs/btrfs/ioctl.c:4333 [inline]
btrfs_ioctl+0x683c/0x7b70 fs/btrfs/ioctl.c:5014
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:874 [inline]
__se_sys_ioctl fs/ioctl.c:860 [inline]
__x64_sys_ioctl+0x193/0x200 fs/ioctl.c:860
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
Reported-by: Hao Sun <sunhao.th@gmail.com>
Link: https://lore.kernel.org/linux-btrfs/CACkBjsZQF19bQ1C6=yetF3BvL10OSORpFUcWXTP6HErshDB4dQ@mail.gmail.com/
Fixes: 340f1aa27f ("btrfs: qgroups: Move transaction management inside btrfs_quota_enable/disable")
CC: stable@vger.kernel.org # 4.19
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bcf141b2eb upstream.
On egress side, xfrm lookup is called from __gre6_xmit() with the
fl6_gre_key field not initialized leading to policies selectors check
failure. Consequently, gre packets are sent without encryption.
On ingress side, INET6_PROTO_NOPOLICY was set, thus packets were not
checked against xfrm policies. Like for egress side, fl6_gre_key should be
correctly set, this is now done in decode_session6().
Fixes: c12b395a46 ("gre: Support GRE over IPv6")
Cc: stable@vger.kernel.org
Signed-off-by: Ghalem Boudour <ghalem.boudour@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f1050c5e1 upstream.
Older mvebu hardware provides PCIe Capability structure only in version 1.
New mvebu and aardvark hardware provides it in version 2. So do not force
version to 2 in pci_bridge_emul_init() and rather allow drivers to set
correct version. Drivers need to set version in pcie_conf.cap field without
overwriting PCI_CAP_LIST_ID register. Both drivers (mvebu and aardvark) do
not provide slot support yet, so do not set PCI_EXP_FLAGS_SLOT flag.
Link: https://lore.kernel.org/r/20211124155944.1290-6-pali@kernel.org
Fixes: 23a5fba4d9 ("PCI: Introduce PCI bridge emulated config space common logic")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 085a9f4343 upstream.
Use down_read_nested() and down_write_nested() when taking the
ctrl->reset_lock rw-sem, passing the number of PCIe hotplug controllers in
the path to the PCI root bus as lock subclass parameter.
This fixes the following false-positive lockdep report when unplugging a
Lenovo X1C8 from a Lenovo 2nd gen TB3 dock:
pcieport 0000:06:01.0: pciehp: Slot(1): Link Down
pcieport 0000:06:01.0: pciehp: Slot(1): Card not present
============================================
WARNING: possible recursive locking detected
5.16.0-rc2+ #621 Not tainted
--------------------------------------------
irq/124-pciehp/86 is trying to acquire lock:
ffff8e5ac4299ef8 (&ctrl->reset_lock){.+.+}-{3:3}, at: pciehp_check_presence+0x23/0x80
but task is already holding lock:
ffff8e5ac4298af8 (&ctrl->reset_lock){.+.+}-{3:3}, at: pciehp_ist+0xf3/0x180
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&ctrl->reset_lock);
lock(&ctrl->reset_lock);
*** DEADLOCK ***
May be due to missing lock nesting notation
3 locks held by irq/124-pciehp/86:
#0: ffff8e5ac4298af8 (&ctrl->reset_lock){.+.+}-{3:3}, at: pciehp_ist+0xf3/0x180
#1: ffffffffa3b024e8 (pci_rescan_remove_lock){+.+.}-{3:3}, at: pciehp_unconfigure_device+0x31/0x110
#2: ffff8e5ac1ee2248 (&dev->mutex){....}-{3:3}, at: device_release_driver+0x1c/0x40
stack backtrace:
CPU: 4 PID: 86 Comm: irq/124-pciehp Not tainted 5.16.0-rc2+ #621
Hardware name: LENOVO 20U90SIT19/20U90SIT19, BIOS N2WET30W (1.20 ) 08/26/2021
Call Trace:
<TASK>
dump_stack_lvl+0x59/0x73
__lock_acquire.cold+0xc5/0x2c6
lock_acquire+0xb5/0x2b0
down_read+0x3e/0x50
pciehp_check_presence+0x23/0x80
pciehp_runtime_resume+0x5c/0xa0
device_for_each_child+0x45/0x70
pcie_port_device_runtime_resume+0x20/0x30
pci_pm_runtime_resume+0xa7/0xc0
__rpm_callback+0x41/0x110
rpm_callback+0x59/0x70
rpm_resume+0x512/0x7b0
__pm_runtime_resume+0x4a/0x90
__device_release_driver+0x28/0x240
device_release_driver+0x26/0x40
pci_stop_bus_device+0x68/0x90
pci_stop_bus_device+0x2c/0x90
pci_stop_and_remove_bus_device+0xe/0x20
pciehp_unconfigure_device+0x6c/0x110
pciehp_disable_slot+0x5b/0xe0
pciehp_handle_presence_or_link_change+0xc3/0x2f0
pciehp_ist+0x179/0x180
This lockdep warning is triggered because with Thunderbolt, hotplug ports
are nested. When removing multiple devices in a daisy-chain, each hotplug
port's reset_lock may be acquired recursively. It's never the same lock, so
the lockdep splat is a false positive.
Because locks at the same hierarchy level are never acquired recursively, a
per-level lockdep class is sufficient to fix the lockdep warning.
The choice to use one lockdep subclass per pcie-hotplug controller in the
path to the root-bus was made to conserve class keys because their number
is limited and the complexity grows quadratically with number of keys
according to Documentation/locking/lockdep-design.rst.
Link: https://lore.kernel.org/linux-pci/20190402021933.GA2966@mit.edu/
Link: https://lore.kernel.org/linux-pci/de684a28-9038-8fc6-27ca-3f6f2f6400d7@redhat.com/
Link: https://lore.kernel.org/r/20211217141709.379663-1-hdegoede@redhat.com
Link: https://bugzilla.kernel.org/show_bug.cgi?id=208855
Reported-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 467ba14e16 upstream.
pmd_huge() is defined to false when HUGETLB_PAGE is not configured, but
the vmap code still installs huge PMDs. This leads to false bad PMD
errors when vunmapping because it is not seen as a huge PTE, and the bad
PMD check catches it. The end result may not be much more serious than
some bad pmd warning messages, because the pmd_none_or_clear_bad() does
what we wanted and clears the huge PTE anyway.
Fix this by checking pmd_is_leaf(), which checks for a PTE regardless of
config options. The whole huge/large/leaf stuff is a tangled mess but
that's kernel-wide and not something we can improve much in arch/powerpc
code.
pmd_page(), pud_page(), etc., called by vmalloc_to_page() on huge vmaps
can similarly trigger a false VM_BUG_ON when CONFIG_HUGETLB_PAGE=n, so
those checks are adjusted. The checks were added by commit d6eacedd1f
("powerpc/book3s: Use config independent helpers for page table walk"),
while implementing a similar fix for other page table walking functions.
Fixes: d909f9109c ("powerpc/64s/radix: Enable HAVE_ARCH_HUGE_VMAP")
Cc: stable@vger.kernel.org # v5.3+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211216103342.609192-1-npiggin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db19c6f1a2 upstream.
While working on the rewrite to the light-weight syscall and futex code, I
experimented with using a hash index based on the user physical address of
atomic variable. This exposed two problems with the lpa and lpa_user defines.
Because of the copy instruction, the pa argument needs to be an early clobber
argument. This prevents gcc from allocating the va and pa arguments to the same
register.
Secondly, the lpa instruction can cause a page fault so we need to catch
exceptions.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Fixes: 116d753308 ("parisc: Use lpa instruction to load physical addresses in driver code")
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c4c6ef2295 upstream.
Prior to commit 6c836d965b ("drm/rockchip: Use the helpers for PSR"),
"PSR exit" used non-blocking analogix_dp_send_psr_spd(). The refactor
started using the blocking variant, for a variety of reasons -- quoting
Sean Paul's potentially-faulty memory:
"""
- To avoid racing a subsequent PSR entry (if exit takes a long time)
- To avoid racing disable/modeset
- We're not displaying new content while exiting PSR anyways, so there
is minimal utility in allowing frames to be submitted
- We're lying to userspace telling them frames are on the screen when
we're just dropping them on the floor
"""
However, I'm finding that this blocking transition is causing upwards of
60+ ms of unneeded latency on PSR-exit, to the point that initial cursor
movements when leaving PSR are unbearably jumpy.
It turns out that we need to meet in the middle somewhere: Sean is right
that we were "lying to userspace" with a non-blocking PSR-exit, but the
new blocking behavior is also waiting too long:
According to the eDP specification, the sink device must support PSR
entry transitions from both state 4 (ACTIVE_RESYNC) and state 0
(INACTIVE). It also states that in ACTIVE_RESYNC, "the Sink device must
display the incoming active frames from the Source device with no
visible glitches and/or artifacts."
Thus, for our purposes, we only need to wait for ACTIVE_RESYNC before
moving on; we are ready to display video, and subsequent PSR-entry is
safe.
Tested on a Samsung Chromebook Plus (i.e., Rockchip RK3399 Gru Kevin),
where this saves about 60ms of latency, for PSR-exit that used to
take about 80ms.
Fixes: 6c836d965b ("drm/rockchip: Use the helpers for PSR")
Cc: <stable@vger.kernel.org>
Cc: Zain Wang <wzz@rock-chips.com>
Cc: Tomasz Figa <tfiga@chromium.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211103135112.v3.1.I67612ea073c3306c71b46a87be894f79707082df@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6dfa2fab8d upstream.
Currently we allow rediculous amounts of kernel memory being allocated
via the etnaviv GEM_SUBMIT ioctl, which is a pretty easy DoS vector. Put
some reasonable limits in to fix this.
The commandstream size is limited to 64KB, which was already a soft limit
on older kernels after which the kernel only took submits on a best effort
base, so there is no userspace that tries to submit commandstreams larger
than this. Even if the whole commandstream is a single incrementing address
load, the size limit also limits the number of potential relocs and
referenced buffers to slightly under 64K, so use the same limit for those
arguments. The performance monitoring infrastructure currently supports
less than 50 performance counter signals, so limiting them to 128 on a
single submit seems like a reasonably future-proof number for now. This
number can be bumped if needed without breaking the interface.
Cc: stable@vger.kernel.org
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a7f4110f7 upstream.
For each endpoint it encounters, fwnode_graph_devcon_match() checks
whether the endpoint's remote port parent device is available. If it is
not, it ignores the endpoint but does not put the reference to the remote
endpoint port parent fwnode. For available devices the fwnode handle
reference is put as expected.
Put the reference for unavailable devices now.
Fixes: 637e9e52b1 ("device connection: Find device connections also from device graphs")
Cc: 5.1+ <stable@vger.kernel.org> # 5.1+
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2c224932f upstream.
There is a race on concurrent 2KB-pgtables release paths when
both upper and lower halves of the containing parent page are
freed, one via page_table_free_rcu() + __tlb_remove_table(),
and the other via page_table_free(). The race might lead to a
corruption as result of remove of list item in page_table_free()
concurrently with __free_page() in __tlb_remove_table().
Let's assume first the lower and next the upper 2KB-pgtables are
freed from a page. Since both halves of the page are allocated
the tracking byte (bits 24-31 of the page _refcount) has value
of 0x03 initially:
CPU0 CPU1
---- ----
page_table_free_rcu() // lower half
{
// _refcount[31..24] == 0x03
...
atomic_xor_bits(&page->_refcount,
0x11U << (0 + 24));
// _refcount[31..24] <= 0x12
...
table = table | (1U << 0);
tlb_remove_table(tlb, table);
}
...
__tlb_remove_table()
{
// _refcount[31..24] == 0x12
mask = _table & 3;
// mask <= 0x01
...
page_table_free() // upper half
{
// _refcount[31..24] == 0x12
...
atomic_xor_bits(
&page->_refcount,
1U << (1 + 24));
// _refcount[31..24] <= 0x10
// mask <= 0x10
...
atomic_xor_bits(&page->_refcount,
mask << (4 + 24));
// _refcount[31..24] <= 0x00
// mask <= 0x00
...
if (mask != 0) // == false
break;
fallthrough;
...
if (mask & 3) // == false
...
else
__free_page(page); list_del(&page->lru);
^^^^^^^^^^^^^^^^^^ RACE! ^^^^^^^^^^^^^^^^^^^^^
} ...
}
The problem is page_table_free() releases the page as result of
lower nibble unset and __tlb_remove_table() observing zero too
early. With this update page_table_free() will use the similar
logic as page_table_free_rcu() + __tlb_remove_table(), and mark
the fragment as pending for removal in the upper nibble until
after the list_del().
In other words, the parent page is considered as unreferenced and
safe to release only when the lower nibble is cleared already and
unsetting a bit in upper nibble results in that nibble turned zero.
Cc: stable@vger.kernel.org
Suggested-by: Vlastimil Babka <vbabka@suse.com>
Reviewed-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3b3404df3 upstream.
Commit a6845e1e1b ("serial: core: Consider rs485 settings to drive
RTS") sought to deassert RTS when opening an rs485-enabled uart port.
That way, the transceiver does not occupy the bus until it transmits
data.
Unfortunately, the commit mixed up the logic and *asserted* RTS instead
of *deasserting* it:
The commit amended uart_port_dtr_rts(), which raises DTR and RTS when
opening an rs232 port. "Raising" actually means lowering the signal
that's coming out of the uart, because an rs232 transceiver not only
changes a signal's voltage level, it also *inverts* the signal. See
the simplified schematic in the MAX232 datasheet for an example:
https://www.ti.com/lit/ds/symlink/max232.pdf
So, to raise RTS on an rs232 port, TIOCM_RTS is *set* in port->mctrl
and that results in the signal being driven low.
In contrast to rs232, the signal level for rs485 Transmit Enable is the
identity, not the inversion: If the transceiver expects a "high" RTS
signal for Transmit Enable, the signal coming out of the uart must also
be high, so TIOCM_RTS must be *cleared* in port->mctrl.
The commit did the exact opposite, but it's easy to see why given the
confusing semantics of rs232 and rs485. Fix it.
Fixes: a6845e1e1b ("serial: core: Consider rs485 settings to drive RTS")
Cc: stable@vger.kernel.org # v4.14+
Cc: Rafael Gago Castano <rgc@hms.se>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Su Bao Cheng <baocheng.su@siemens.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/9395767847833f2f3193c49cde38501eeb3b5669.1639821059.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e388164ea3 upstream.
The acceptable maximum value of lend parameter in
filemap_write_and_wait_range() is LLONG_MAX rather than -1. And there is
also some logic depending on LLONG_MAX check in write_cache_pages(). So
let's pass LLONG_MAX to filemap_write_and_wait_range() in
fuse_writeback_range() instead.
Fixes: 59bda8ecee ("fuse: flush extending writes")
Signed-off-by: Xie Yongji <xieyongji@bytedance.com>
Cc: <stable@vger.kernel.org> # v5.15
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce2f46f353 upstream.
While working with Xen's libxenvchan library I have faced an issue with
unmap notifications sent in wrong order if both UNMAP_NOTIFY_SEND_EVENT
and UNMAP_NOTIFY_CLEAR_BYTE were requested: first we send an event channel
notification and then clear the notification byte which renders in the below
inconsistency (cli_live is the byte which was requested to be cleared on unmap):
[ 444.514243] gntdev_put_map UNMAP_NOTIFY_SEND_EVENT map->notify.event 6
libxenvchan_is_open cli_live 1
[ 444.515239] __unmap_grant_pages UNMAP_NOTIFY_CLEAR_BYTE at 14
Thus it is not possible to reliably implement the checks like
- wait for the notification (UNMAP_NOTIFY_SEND_EVENT)
- check the variable (UNMAP_NOTIFY_CLEAR_BYTE)
because it is possible that the variable gets checked before it is cleared
by the kernel.
To fix that we need to re-order the notifications, so the variable is first
gets cleared and then the event channel notification is sent.
With this fix I can see the correct order of execution:
[ 54.522611] __unmap_grant_pages UNMAP_NOTIFY_CLEAR_BYTE at 14
[ 54.537966] gntdev_put_map UNMAP_NOTIFY_SEND_EVENT map->notify.event 6
libxenvchan_is_open cli_live 0
Cc: stable@vger.kernel.org
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20211210092817.580718-1-andr2000@gmail.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84cc695897 upstream.
When using the tpm_tis-spi driver on a system missing the physical TPM,
a null pointer exception was observed.
[ 0.938677] Unable to handle kernel NULL pointer dereference at virtual address 00000004
[ 0.939020] pgd = 10c753cb
[ 0.939237] [00000004] *pgd=00000000
[ 0.939808] Internal error: Oops: 5 [#1] SMP ARM
[ 0.940157] CPU: 0 PID: 48 Comm: kworker/u4:1 Not tainted 5.15.10-dd1e40c #1
[ 0.940364] Hardware name: Generic DT based system
[ 0.940601] Workqueue: events_unbound async_run_entry_fn
[ 0.941048] PC is at tpm_tis_remove+0x28/0xb4
[ 0.941196] LR is at tpm_tis_core_init+0x170/0x6ac
This is due to an attempt in 'tpm_tis_remove' to use the drvdata, which
was not initialized in 'tpm_tis_core_init' prior to the first error.
Move the initialization of drvdata earlier so 'tpm_tis_remove' has
access to it.
Signed-off-by: Patrick Williams <patrick@stwcx.xyz>
Fixes: 79ca6f74da ("tpm: fix Atmel TPM crash caused by too frequent queries")
Cc: stable@vger.kernel.org
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit efd21e10fc upstream.
When enable the kernel debug config, there is below calltrace detected:
BUG: using smp_processor_id() in preemptible [00000000] code: cryptomgr_test/339
caller is debug_smp_processor_id+0x20/0x30
CPU: 9 PID: 339 Comm: cryptomgr_test Not tainted 5.10.63-yocto-standard #1
Hardware name: NXP Layerscape LX2160ARDB (DT)
Call trace:
dump_backtrace+0x0/0x1a0
show_stack+0x24/0x30
dump_stack+0xf0/0x13c
check_preemption_disabled+0x100/0x110
debug_smp_processor_id+0x20/0x30
dpaa2_caam_enqueue+0x10c/0x25c
......
cryptomgr_test+0x38/0x60
kthread+0x158/0x164
ret_from_fork+0x10/0x38
According to the comment in commit ac5d15b4519f("crypto: caam/qi2
- use affine DPIOs "), because preemption is no longer disabled
while trying to enqueue an FQID, it might be possible to run the
enqueue on a different CPU(due to migration, when in process context),
however this wouldn't be a functionality issue. But there will be
above calltrace when enable kernel debug config. So, replace this_cpu_ptr
with raw_cpu_ptr to avoid above call trace.
Fixes: ac5d15b451 ("crypto: caam/qi2 - use affine DPIOs")
Cc: stable@vger.kernel.org
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29009604ad upstream.
The include/linux/crypto.h struct crypto_alg field cra_driver_name description
states "Unique name of the transformation provider. " ... " this contains the
name of the chip or provider and the name of the transformation algorithm."
In case of the stm32-crc driver, field cra_driver_name is identical for all
registered transformation providers and set to the name of the driver itself,
which is incorrect. This patch fixes it by assigning a unique cra_driver_name
to each registered transformation provider.
The kernel crash is triggered when the driver calls crypto_register_shashes()
which calls crypto_register_shash(), which calls crypto_register_alg(), which
calls __crypto_register_alg(), which returns -EEXIST, which is propagated
back through this call chain. Upon -EEXIST from crypto_register_shash(), the
crypto_register_shashes() starts unregistering the providers back, and calls
crypto_unregister_shash(), which calls crypto_unregister_alg(), and this is
where the BUG() triggers due to incorrect cra_refcnt.
Fixes: b51dbe9091 ("crypto: stm32 - Support for STM32 CRC32 crypto module")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: <stable@vger.kernel.org> # 4.12+
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Fabien Dessenne <fabien.dessenne@st.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Lionel Debieve <lionel.debieve@st.com>
Cc: Nicolas Toromanoff <nicolas.toromanoff@st.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-crypto@vger.kernel.org
Acked-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2aec59be0 upstream.
This fix is basically the same as 3d6b661330 ("crypto: stm32 -
Revert broken pm_runtime_resume_and_get changes"), just for the omap
driver. If the return value isn't used, then pm_runtime_get_sync()
has to be used for ensuring that the usage count is balanced.
Fixes: 1f34cc4a8d ("crypto: omap-aes - Fix PM reference leak on omap-aes.c")
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 95339b7067 ]
A large number of the following errors is reported when compiling
with clang:
cvmx-bootinfo.h:326:3: error: adding 'int' to a string does not append to the string [-Werror,-Wstring-plus-int]
ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_NULL)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cvmx-bootinfo.h:321:20: note: expanded from macro 'ENUM_BRD_TYPE_CASE'
case x: return(#x + 16); /* Skip CVMX_BOARD_TYPE_ */
~~~^~~~
cvmx-bootinfo.h:326:3: note: use array indexing to silence this warning
cvmx-bootinfo.h:321:20: note: expanded from macro 'ENUM_BRD_TYPE_CASE'
case x: return(#x + 16); /* Skip CVMX_BOARD_TYPE_ */
^
Follow the prompts to use the address operator '&' to fix this error.
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79a7f77b9b ]
Jay Chen reported that using a kdump kernel on a GICv4.1 system
results in a RAS error being delivered when the secondary kernel
configures the ITS's view of the new VPE table.
As it turns out, that's because each RD still has a pointer to
the previous instance of the VPE table, and that particular
implementation is very upset by seeing two bits of the HW that
should point to the same table with different values.
To solve this, let's invalidate any reference that any RD has to
the VPE table when discovering the RDs. The ITS can then be
programmed as expected.
Reported-by: Jay Chen <jkchen@linux.alibaba.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Link: https://lore.kernel.org/r/20211214064716.21407-1-jkchen@linux.alibaba.com
Link: https://lore.kernel.org/r/20211216144804.1578566-1-maz@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 858779df1c ]
This was found by coccicheck:
./arch/mips/cavium-octeon/octeon-platform.c, 332, 1-7, ERROR missing
put_device; call of_find_device_by_node on line 324, but without a
corresponding object release within this function.
./arch/mips/cavium-octeon/octeon-platform.c, 395, 1-7, ERROR missing
put_device; call of_find_device_by_node on line 387, but without a
corresponding object release within this function.
./arch/mips/cavium-octeon/octeon-usb.c, 512, 3-9, ERROR missing
put_device; call of_find_device_by_node on line 515, but without a
corresponding object release within this function.
./arch/mips/cavium-octeon/octeon-usb.c, 543, 1-7, ERROR missing
put_device; call of_find_device_by_node on line 515, but without a
corresponding object release within this function.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Ye Guojin <ye.guojin@zte.com.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f05f2429ee ]
When memory allocation of iinfo or block allocation fails, already
allocated struct udf_inode_info gets freed with iput() and
udf_evict_inode() may look at inode fields which are not properly
initialized. Fix it by marking inode bad before dropping reference to it
in udf_new_inode().
Reported-by: syzbot+9ca499bb57a2b9e4c652@syzkaller.appspotmail.com
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06e629c25d ]
In panic path, fadump is triggered via a panic notifier function.
Before calling panic notifier functions, smp_send_stop() gets called,
which stops all CPUs except the panic'ing CPU. Commit 8389b37dff
("powerpc: stop_this_cpu: remove the cpu from the online map.") and
again commit bab26238bb ("powerpc: Offline CPU in stop_this_cpu()")
started marking CPUs as offline while stopping them. So, if a kernel
has either of the above commits, vmcore captured with fadump via panic
path would not process register data for all CPUs except the panic'ing
CPU. Sample output of crash-utility with such vmcore:
# crash vmlinux vmcore
...
KERNEL: vmlinux
DUMPFILE: vmcore [PARTIAL DUMP]
CPUS: 1
DATE: Wed Nov 10 09:56:34 EST 2021
UPTIME: 00:00:42
LOAD AVERAGE: 2.27, 0.69, 0.24
TASKS: 183
NODENAME: XXXXXXXXX
RELEASE: 5.15.0+
VERSION: #974 SMP Wed Nov 10 04:18:19 CST 2021
MACHINE: ppc64le (2500 Mhz)
MEMORY: 8 GB
PANIC: "Kernel panic - not syncing: sysrq triggered crash"
PID: 3394
COMMAND: "bash"
TASK: c0000000150a5f80 [THREAD_INFO: c0000000150a5f80]
CPU: 1
STATE: TASK_RUNNING (PANIC)
crash> p -x __cpu_online_mask
__cpu_online_mask = $1 = {
bits = {0x2, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0}
}
crash>
crash>
crash> p -x __cpu_active_mask
__cpu_active_mask = $2 = {
bits = {0xff, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0}
}
crash>
While this has been the case since fadump was introduced, the issue
was not identified for two probable reasons:
- In general, the bulk of the vmcores analyzed were from crash
due to exception.
- The above did change since commit 8341f2f222 ("sysrq: Use
panic() to force a crash") started using panic() instead of
deferencing NULL pointer to force a kernel crash. But then
commit de6e5d3841 ("powerpc: smp_send_stop do not offline
stopped CPUs") stopped marking CPUs as offline till kernel
commit bab26238bb ("powerpc: Offline CPU in stop_this_cpu()")
reverted that change.
To ensure post processing register data of all other CPUs happens
as intended, let panic() function take the crash friendly path (read
crash_smp_send_stop()) with the help of crash_kexec_post_notifiers
option. Also, as register data for all CPUs is captured by f/w, skip
IPI callbacks here for fadump, to avoid any complications in finding
the right backtraces.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211207103719.91117-2-hbathini@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 219572d2fc ]
Kdump can be triggered after panic_notifers since commit f06e5153f4
("kernel/panic.c: add "crash_kexec_post_notifiers" option for kdump
after panic_notifers") introduced crash_kexec_post_notifiers option.
But using this option would mean smp_send_stop(), that marks all other
CPUs as offline, gets called before kdump is triggered. As a result,
kdump routines fail to save other CPUs' registers. To fix this, kdump
friendly crash_smp_send_stop() function was introduced with kernel
commit 0ee59413c9 ("x86/panic: replace smp_send_stop() with kdump
friendly version in panic path"). Override this kdump friendly weak
function to handle crash_kexec_post_notifiers option appropriately
on powerpc.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
[Fixed signature of crash_stop_this_cpu() - reported by lkp@intel.com]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211207103719.91117-1-hbathini@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c42e95420 ]
A mis-match between reported and actual mitigation is not restricted to the
Vulnerable case. The guest might also report the mitigation as "Software
count cache flush" and the host will still mitigate with branch cache
disabled.
So, instead of skipping depending on the detected mitigation, simply skip
whenever the detected miss_percent is the expected one for a fully
mitigated system, that is, above 95%.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211207130557.40566-1-cascardo@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2c6c22fa8 ]
LLVM's integrated assembler does not support 'slti <reg>, <imm>':
<instantiation>:16:12: error: invalid operand for instruction
slti $12, (0x6300 | 0x0008)
^
arch/mips/kernel/head.S:86:2: note: while in macro instantiation
kernel_entry_setup # cpu specific setup
^
<instantiation>:16:12: error: invalid operand for instruction
slti $12, (0x6300 | 0x0008)
^
arch/mips/kernel/head.S:150:2: note: while in macro instantiation
smp_slave_setup
^
To increase compatibility with LLVM's integrated assembler, use the full
form of 'slti <reg>, <reg>, <imm>', which matches the rest of
arch/mips/. This does not result in any change for GNU as.
Link: https://github.com/ClangBuiltLinux/linux/issues/1526
Reported-by: Ryutaroh Matsumoto <ryutaroh@ict.e.titech.ac.jp>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6fadb494a6 ]
Currently ALSA sequencer core tries to process the queued events as
much as possible when they become dispatchable. If applications try
to queue too massive events to be processed at the very same timing,
the sequencer core would still try to process such all events, either
in the interrupt context or via some notifier; in either away, it
might be a cause of RCU stall or such problems.
As a potential workaround for those problems, this patch adds the
upper limit of the amount of events to be processed. The remaining
events are processed in the next batch, so they won't be lost.
For the time being, it's limited up to 1000 events per queue, which
should be high enough for any normal usages.
Reported-by: Zqiang <qiang.zhang1211@gmail.com>
Reported-by: syzbot+bb950e68b400ab4f65f8@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/20211102033222.3849-1-qiang.zhang1211@gmail.com
Link: https://lore.kernel.org/r/20211207165146.2888-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 792020907b ]
H_COPY_TOFROM_GUEST is an hcall for an upper level VM to access its nested
VMs memory. The userspace can trigger WARN_ON_ONCE(!(gfp & __GFP_NOWARN))
in __alloc_pages() by constructing a tiny VM which only does
H_COPY_TOFROM_GUEST with a too big GPR9 (number of bytes to copy).
This silences the warning by adding __GFP_NOWARN.
Spotted by syzkaller.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210901084550.1658699-1-aik@ozlabs.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 511d25d6b7 ]
The userspace can trigger "vmalloc size %lu allocation failure: exceeds
total pages" via the KVM_SET_USER_MEMORY_REGION ioctl.
This silences the warning by checking the limit before calling vzalloc()
and returns ENOMEM if failed.
This does not call underlying valloc helpers as __vmalloc_node() is only
exported when CONFIG_TEST_VMALLOC_MODULE and __vmalloc_node_range() is
not exported at all.
Spotted by syzkaller.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[mpe: Use 'size' for the variable rather than 'cb']
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210901084512.1658628-1-aik@ozlabs.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff54938dd1 ]
There are reports that 48kHz audio does not work on the WeTek Play 2
(which uses a GXBB SoC), while 44.1kHz audio works fine on the same
board. There are also reports of 48kHz audio working fine on GXL and
GXM SoCs, which are using an (almost) identical AIU (audio controller).
Experimenting has shown that MPLL0 is causing this problem. In the .dts
we have by default:
assigned-clocks = <&clkc CLKID_MPLL0>,
<&clkc CLKID_MPLL1>,
<&clkc CLKID_MPLL2>;
assigned-clock-rates = <294912000>,
<270950400>,
<393216000>;
The MPLL0 rate is divisible by 48kHz without remainder and the MPLL1
rate is divisible by 44.1kHz without remainder. Swapping these two clock
rates "fixes" 48kHz audio but breaks 44.1kHz audio.
Everything looks normal when looking at the info provided by the common
clock framework while playing 48kHz audio (via I2S with mclk-fs = 256):
mpll_prediv 1 1 0 2000000000
mpll0_div 1 1 0 294909641
mpll0 1 1 0 294909641
cts_amclk_sel 1 1 0 294909641
cts_amclk_div 1 1 0 12287902
cts_amclk 1 1 0 12287902
meson-clk-msr however shows that the actual MPLL0 clock is off by more
than 38MHz:
mp0_out 333322917 +/-10416Hz
The rate seen by meson-clk-msr is very close to what we would get when
SDM (the fractional part) was ignored:
(2000000000Hz * 16384) / ((16384 * 6) = 333.33MHz
If SDM was considered the we should get close to:
(2000000000Hz * 16384) / ((16384 * 6) + 12808) = 294.9MHz
Further experimenting shows that HHI_MPLL_CNTL7[15] does not have any
effect on the rate of MPLL0 as seen my meson-clk-msr (regardless of
whether that bit is zero or one the rate is always the same according to
meson-clk-msr). Using HHI_MPLL_CNTL[25] on the other hand as SDM_EN
results in SDM being considered for the rate output by the hardware. The
rate - as seen by meson-clk-msr - matches with what we expect when
SDM_EN is enabled (fractional part is being considered, resulting in a
294.9MHz output) or disable (fractional part being ignored, resulting in
a 333.33MHz output).
Reported-by: Christian Hewitt <christianshewitt@gmail.com>
Tested-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20211031135006.1508796-1-martin.blumenstingl@googlemail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ebe82cf92c ]
Current I2C reset procedure is broken in two ways:
1) It only generate 1 START instead of 9 STARTs and STOP.
2) It leaves the bus Busy so every I2C xfer after the first
fixup calls the reset routine again, for every xfer there after.
This fixes both errors.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit effa453168 ]
If an invalid block size is provided, reject it instead of silently
changing it to a supported value. Especially critical I see the case of
a write transfer with block length 0. In this case we have no guarantee
that the byte we would write is valid. When silently reducing a read to
32 bytes then we don't return an error and the caller may falsely
assume that we returned the full requested data.
If this change should break any (broken) caller, then I think we should
fix the caller.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5dad4ba68a ]
It is possible for all CPUs to miss the pending cpumask becoming clear,
and then nobody resetting it, which will cause the lockup detector to
stop working. It will eventually expire, but watchdog_smp_panic will
avoid doing anything if the pending mask is clear and it will never be
reset.
Order the cpumask clear vs the subsequent test to close this race.
Add an extra check for an empty pending mask when the watchdog fires and
finds its bit still clear, to try to catch any other possible races or
bugs here and keep the watchdog working. The extra test in
arch_touch_nmi_watchdog is required to prevent the new warning from
firing off.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Laurent Dufour <ldufour@linux.ibm.com>
Debugged-by: Laurent Dufour <ldufour@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211110025056.2084347-2-npiggin@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a841fd009e ]
for_each_node_by_name performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression e,e1;
local idexpression n;
@@
for_each_node_by_name(n, e1) {
... when != of_node_put(n)
when != e = n
(
return n;
|
+ of_node_put(n);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1448051604-25256-7-git-send-email-Julia.Lawall@lip6.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6e82647ff ]
for_each_compatible_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression e;
local idexpression n;
@@
@@
local idexpression n;
expression e;
@@
for_each_compatible_node(n,...) {
...
(
of_node_put(n);
|
e = n
|
+ of_node_put(n);
? break;
)
...
}
... when != n
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1448051604-25256-2-git-send-email-Julia.Lawall@lip6.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6aa86cff4 ]
Most distro kernels have this option enabled, to improve debug output.
Lockdep also selects it.
Enable this in the defconfig kernel as well, to make it more
representative of what people are using on x86.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/YdTn7gssoMVDMgMw@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e9d4b460f ]
In handle_interruption(), we call faulthandler_disabled() to check whether the
fault handler is not disabled. If the fault handler is disabled, we immediately
call do_page_fault(). It then calls faulthandler_disabled(). If disabled,
do_page_fault() attempts to fixup the exception by jumping to no_context:
no_context:
if (!user_mode(regs) && fixup_exception(regs)) {
return;
}
parisc_terminate("Bad Address (null pointer deref?)", regs, code, address);
Apart from the error messages, the two blocks of code perform the same
function.
We can avoid two calls to faulthandler_disabled() by a simple revision
to the code in handle_interruption().
Note: I didn't try to fix the formatting of this code block.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73c7733f12 ]
When crng_fast_load() is called by add_hwgenerator_randomness(), we
currently will advance to crng_init==1 once we've acquired 64 bytes, and
then throw away the rest of the buffer. Usually, that is not a problem:
When add_hwgenerator_randomness() gets called via EFI or DT during
setup_arch(), there won't be any IRQ randomness. Therefore, the 64 bytes
passed by EFI exactly matches what is needed to advance to crng_init==1.
Usually, DT seems to pass 64 bytes as well -- with one notable exception
being kexec, which hands over 128 bytes of entropy to the kexec'd kernel.
In that case, we'll advance to crng_init==1 once 64 of those bytes are
consumed by crng_fast_load(), but won't continue onward feeding in bytes
to progress to crng_init==2. This commit fixes the issue by feeding
any leftover bytes into the next phase in add_hwgenerator_randomness().
[linux@dominikbrodowski.net: rewrite commit message]
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93a770b7e1 ]
struct uart_port contains a cached copy of the Modem Control signals.
It is used to skip register writes in uart_update_mctrl() if the new
signal state equals the old signal state. It also avoids a register
read to obtain the current state of output signals.
When a uart_port is registered, uart_configure_port() changes signal
state but neglects to keep the cached copy in sync. That may cause
a subsequent register write to be incorrectly skipped. Fix it before
it trips somebody up.
This behavior has been present ever since the serial core was introduced
in 2002:
https://git.kernel.org/history/history/c/33c0d1b0c3eb
So far it was never an issue because the cached copy is initialized to 0
by kzalloc() and when uart_configure_port() is executed, at most DTR has
been set by uart_set_options() or sunsu_console_setup(). Therefore,
a stable designation seems unnecessary.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/bceeaba030b028ed810272d55d5fc6f3656ddddb.1641129752.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08a0c6dff9 ]
pl010_set_termios() briefly resets the CR register to zero.
Where does this register write come from?
The PL010 driver's IRQ handler ambauart_int() originally modified the CR
register without holding the port spinlock. ambauart_set_termios() also
modified that register. To prevent concurrent read-modify-writes by the
IRQ handler and to prevent transmission while changing baudrate,
ambauart_set_termios() had to disable interrupts. That is achieved by
writing zero to the CR register.
However in 2004 the PL010 driver was amended to acquire the port
spinlock in the IRQ handler, obviating the need to disable interrupts in
->set_termios():
https://git.kernel.org/history/history/c/157c0342e591
That rendered the CR register write obsolete. Drop it.
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/fcaff16e5b1abb4cc3da5a2879ac13f278b99ed0.1641128728.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14e2976fba ]
The RPMh regulator driver is much newer and gets more attention, which in
consequence makes it do a few things better. Update qcom_smd-regulator's
probe function to mimic what rpmh-regulator does to address a couple of
issues:
- Probe defer now works correctly, before it used to, well,
kinda just die.. This fixes reliable probing on (at least) PM8994,
because Linux apparently cannot deal with supply map dependencies yet..
- Regulator data is now matched more sanely: regulator data is matched
against each individual regulator node name and throwing an -EINVAL if
data is missing, instead of just assuming everything is fine and
iterating over all subsequent array members.
- status = "disabled" will now work for disabling individual regulators in
DT. Previously it didn't seem to do much if anything at all.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20211230023442.1123424-1-konrad.dybcio@somainline.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e4f325a0a ]
The four RGMII interface modes take care of the required RGMII delay
configuration at the PHY and should not be limited by the network MAC
driver. Sadly, gemini was only permitting RGMII mode with no delays,
which would require the required delay to be inserted via PCB tracking
or by the MAC.
However, there are designs that require the PHY to add the delay, which
is impossible without Gemini permitting the other three PHY interface
modes. Fix the driver to allow these.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Link: https://lore.kernel.org/r/E1n4mpT-002PLd-Ha@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f22725c95e ]
Corentin Labbe reports that the SSI 1328 does not work when allowing
the PHY to operate at gigabit speeds, but does work with the generic
PHY driver.
This appears to be because m88e1118_config_init() writes a fixed value
to the MSCR register, claiming that this is to enable 1G speeds.
However, this always sets bits 4 and 5, enabling RGMII transmit and
receive delays. The suspicion is that the original board this was
added for required the delays to make 1G speeds work.
Add the necessary configuration for RGMII delays for the 88E1118 to
bring this into line with the requirements for RGMII support, and thus
make the SSI 1328 work.
Corentin Labbe has tested this on gemini-ssi1328 and gemini-ns2502.
Reported-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d43e427174 ]
Locally generated packets ingress the device through its CPU port. When
the CPU port is congested and there are not enough credits in its
headroom buffer, packets can be dropped.
While this might be acceptable for data packets that traverse the
network, configuration packets exchanged between the host and the device
(EMADs) should not be subjected to this flow control.
The "sdq_lp" bit in the SDQ (Send Descriptor Queue) context allows the
host to instruct the device to treat packets sent on this queue as
"local processing" and always process them, regardless of the state of
the CPU port's headroom.
Add the definition of this bit and set it for the dedicated SDQ reserved
for the transmission of EMAD packets. This makes the "local processing"
bit in the WQE (Work Queue Element) redundant, so clear it.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04be6d337d ]
Some AP can possibly try non-standard VHT rate and mac80211 warns and drops
packets, and leads low TCP throughput.
Rate marked as a VHT rate but data is invalid: MCS: 10, NSS: 2
WARNING: CPU: 1 PID: 7817 at net/mac80211/rx.c:4856 ieee80211_rx_list+0x223/0x2f0 [mac8021
Since commit c27aa56a72 ("cfg80211: add VHT rate entries for MCS-10 and MCS-11")
has added, mac80211 adds this support as well.
After this patch, throughput is good and iw can get the bitrate:
rx bitrate: 975.1 MBit/s VHT-MCS 10 80MHz short GI VHT-NSS 2
or
rx bitrate: 1083.3 MBit/s VHT-MCS 11 80MHz short GI VHT-NSS 2
Buglink: https://bugzilla.suse.com/show_bug.cgi?id=1192891
Reported-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://lore.kernel.org/r/20220103013623.17052-1-pkshih@realtek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f05c09d6b ]
If we're looking for leafs that point to a data extent we want to record
the extent items that point at our bytenr. At this point we have the
reference and we know for a fact that this leaf should have a reference
to our bytenr. However if there's some sort of corruption we may not
find any references to our leaf, and thus could end up with eie == NULL.
Replace this BUG_ON() with an ASSERT() and then return -EUCLEAN for the
mortals.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fcba0120ed ]
We search for an extent entry with .offset = -1, which shouldn't be a
thing, but corruption happens. Add an ASSERT() for the developers,
return -EUCLEAN for mortals.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e96c1197ac ]
The EC/ACPI firmware on Lenovo ThinkPads used to report a status
of "Unknown" when the battery is between the charge start and
charge stop thresholds. On Windows, it reports "Not Charging"
so the quirk has been added to also report correctly.
Now the "status" attribute returns "Not Charging" when the
battery on ThinkPads is not physicaly charging.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11c9cc95f8 ]
== Description ==
Setting values of pm attributes through sysfs
should not be allowed in SRIOV mode.
These calls will not be processed by FW anyway,
but error handling on sysfs level should be improved.
== Changes ==
This patch prohibits performing of all set commands
in SRIOV mode on sysfs level.
It offers better error handling as calls that are
not allowed will not be propagated further.
== Test ==
Writing to any sysfs file in passthrough mode will succeed.
Writing to any sysfs file in ONEVF mode will yield error:
"calling process does not have sufficient permission to execute a command".
Signed-off-by: Marina Nikolic <Marina.Nikolic@amd.com>
Acked-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11544d77e3 ]
Some boards(like RX550) seem to have garbage in the upper
16 bits of the vram size register. Check for
this and clamp the size properly. Fixes
boards reporting bogus amounts of vram.
after add this patch,the maximum GPU VRAM size is 64GB,
otherwise only 64GB vram size will be used.
Signed-off-by: Zongmin Zhou<zhouzongmin@kylinos.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d4e0b3abb ]
ACPICA commit 3dd7e1f3996456ef81bfe14cba29860e8d42949e
According to ACPI 6.4, Section 16.2, the CPU cache flushing is
required on entering to S1, S2, and S3, but the ACPICA code
flushes the CPU cache regardless of the sleep state.
Blind cache flush on entering S5 causes problems for TDX.
Flushing happens with WBINVD that is not supported in the TDX
environment.
TDX only supports S5 and adjusting ACPICA code to conform to the
spec more strictly fixes the issue.
Link: https://github.com/acpica/acpica/commit/3dd7e1f3
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a3b8655db ]
ACPICA commit 41be6afacfdaec2dba3a5ed368736babc2a7aa5c
With the PCC Opregion in the firmware and we are hitting below kernel crash:
-->8
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000010
Workqueue: pm pm_runtime_work
pstate: 80000005 (Nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : __memcpy+0x54/0x260
lr : acpi_ex_write_data_to_field+0xb8/0x194
Call trace:
__memcpy+0x54/0x260
acpi_ex_store_object_to_node+0xa4/0x1d4
acpi_ex_store+0x44/0x164
acpi_ex_opcode_1A_1T_1R+0x25c/0x508
acpi_ds_exec_end_op+0x1b4/0x44c
acpi_ps_parse_loop+0x3a8/0x614
acpi_ps_parse_aml+0x90/0x2f4
acpi_ps_execute_method+0x11c/0x19c
acpi_ns_evaluate+0x1ec/0x2b0
acpi_evaluate_object+0x170/0x2b0
acpi_device_set_power+0x118/0x310
acpi_dev_suspend+0xd4/0x180
acpi_subsys_runtime_suspend+0x28/0x38
__rpm_callback+0x74/0x328
rpm_suspend+0x2d8/0x624
pm_runtime_work+0xa4/0xb8
process_one_work+0x194/0x25c
worker_thread+0x260/0x49c
kthread+0x14c/0x30c
ret_from_fork+0x10/0x20
Code: f9000006 f81f80a7 d65f03c0 361000c2 (b9400026)
---[ end trace 24d8a032fa77b68a ]---
The reason for the crash is that the PCC channel index passed via region.address
in acpi_ex_store_object_to_node is interpreted as the channel subtype
incorrectly.
Assuming the PCC op_region support is not used by any other type, let us
remove the subtype check as the AML has no access to the subtype information.
Once we remove it, the kernel crash disappears and correctly complains about
missing PCC Opregion handler.
ACPI Error: No handler for Region [PFRM] ((____ptrval____)) [PCC] (20210730/evregion-130)
ACPI Error: Region PCC (ID=10) has no handler (20210730/exfldio-261)
ACPI Error: Aborting method \_SB.ETH0._PS3 due to previous error (AE_NOT_EXIST) (20210730/psparse-531)
Link: https://github.com/acpica/acpica/commit/41be6afa
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24ea5f90ec ]
ACPICA commit d984f12041392fa4156b52e2f7e5c5e7bc38ad9e
If Operand[0] is a reference of the ACPI_REFCLASS_REFOF class,
acpi_ex_opcode_1A_0T_1R () calls acpi_ns_get_attached_object () to
obtain return_desc which may require additional resolution with
the help of acpi_ex_read_data_from_field (). If the latter fails,
the reference counter of the original return_desc is decremented
which is incorrect, because acpi_ns_get_attached_object () does not
increment the reference counter of the object returned by it.
This issue may lead to premature deletion of the attached object
while it is still attached and a use-after-free and crash in the
host OS. For example, this may happen when on evaluation of ref_of()
a local region field where there is no registered handler for the
given Operation Region.
Fix it by making acpi_ex_opcode_1A_0T_1R () return Status right away
after a acpi_ex_read_data_from_field () failure.
Link: https://github.com/acpica/acpica/commit/d984f120
Link: https://github.com/acpica/acpica/pull/685
Reported-by: Lenny Szubowicz <lszubowi@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1cdfe9e346 ]
ACPICA commit c11af67d8f7e3d381068ce7771322f2b5324d687
If original_count is 0 in acpi_ut_update_ref_count (),
acpi_ut_delete_internal_obj () is invoked for the target object, which is
incorrect, because that object has been deleted once already and the
memory allocated to store it may have been reclaimed and allocated
for a different purpose by the host OS. Moreover, a confusing debug
message following the "Reference Count is already zero, cannot
decrement" warning is printed in that case.
To fix this issue, make acpi_ut_update_ref_count () return after finding
that original_count is 0 and printing the above warning.
Link: https://github.com/acpica/acpica/commit/c11af67d
Link: https://github.com/acpica/acpica/pull/652
Reported-by: Mark Asselstine <mark.asselstine@windriver.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f81bdeaf81 ]
ACPICA commit bc02c76d518135531483dfc276ed28b7ee632ce1
The current ACPI_ACCESS_*_WIDTH defines do not provide a way to
test that size is small enough to not cause an overflow when
applied to a 32-bit integer.
Rather than adding more magic numbers, add ACPI_ACCESS_*_SHIFT,
ACPI_ACCESS_*_MAX, and ACPI_ACCESS_*_DEFAULT #defines and
redefine ACPI_ACCESS_*_WIDTH in terms of the new #defines.
This was inititally reported on Linux where a size of 102 in
ACPI_ACCESS_BIT_WIDTH caused an overflow error in the SPCR
initialization code.
Link: https://github.com/acpica/acpica/commit/bc02c76d
Signed-off-by: Mark Langsdorf <mlangsdo@redhat.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa39cc6757 ]
GC task can deadlock in read_cache_page() because it may attempt
to release a page that is actually allocated by another task in
jffs2_write_begin().
The reason is that in jffs2_write_begin() there is a small window
a cache page is allocated for use but not set Uptodate yet.
This ends up with a deadlock between two tasks:
1) A task (e.g. file copy)
- jffs2_write_begin() locks a cache page
- jffs2_write_end() tries to lock "alloc_sem" from
jffs2_reserve_space() <-- STUCK
2) GC task (jffs2_gcd_mtd3)
- jffs2_garbage_collect_pass() locks "alloc_sem"
- try to lock the same cache page in read_cache_page() <-- STUCK
So to avoid this deadlock, hold "alloc_sem" in jffs2_write_begin()
while reading data in a cache page.
Signed-off-by: Kyeong Yoo <kyeong.yoo@alliedtelesis.co.nz>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdd156955f ]
Some GPU heavy test programs manage to trigger the hangcheck quite often.
If there are no other GPU users in the system and the test program
exhibits a very regular structure in the commandstreams that are being
submitted, we can end up with two distinct submits managing to trigger
the hangcheck with the FE in a very similar address range. This leads
the hangcheck to believe that the GPU is stuck, while in reality the GPU
is already busy working on a different job. To avoid those spurious
GPU resets, also remember and consider the last completed fence seqno
in the hang check.
Reported-by: Joerg Albert <joerg.albert@iav.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e484b3e96 ]
Kernel generates mapping change message, XFRM_MSG_MAPPING,
when a source port chage is detected on a input state with UDP
encapsulation set. Kernel generates a message for each IPsec packet
with new source port. For a high speed flow per packet mapping change
message can be excessive, and can overload the user space listener.
Introduce rate limiting for XFRM_MSG_MAPPING message to the user space.
The rate limiting is configurable via netlink, when adding a new SA or
updating it. Use the new attribute XFRMA_MTIMER_THRESH in seconds.
v1->v2 change:
update xfrm_sa_len()
v2->v3 changes:
use u32 insted unsigned long to reduce size of struct xfrm_state
fix xfrm_ompat size Reported-by: kernel test robot <lkp@intel.com>
accept XFRM_MSG_MAPPING only when XFRMA_ENCAP is present
Co-developed-by: Thomas Egerer <thomas.egerer@secunet.com>
Signed-off-by: Thomas Egerer <thomas.egerer@secunet.com>
Signed-off-by: Antony Antony <antony.antony@secunet.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cfb4c313be ]
This set HCI_QUIRK_VALID_LE_STATES quirk which is required for the likes
of experimental LE simultaneous roles.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ce708f54c ]
Large pkt_len can lead to out-out-bound memcpy. Current
ath9k_hif_usb_rx_stream allows combining the content of two urb
inputs to one pkt. The first input can indicate the size of the
pkt. Any remaining size is saved in hif_dev->rx_remain_len.
While processing the next input, memcpy is used with rx_remain_len.
4-byte pkt_len can go up to 0xffff, while a single input is 0x4000
maximum in size (MAX_RX_BUF_SIZE). Thus, the patch adds a check for
pkt_len which must not exceed 2 * MAX_RX_BUG_SIZE.
BUG: KASAN: slab-out-of-bounds in ath9k_hif_usb_rx_cb+0x490/0xed7 [ath9k_htc]
Read of size 46393 at addr ffff888018798000 by task kworker/0:1/23
CPU: 0 PID: 23 Comm: kworker/0:1 Not tainted 5.6.0 #63
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
BIOS rel-1.10.2-0-g5f4c7b1-prebuilt.qemu-project.org 04/01/2014
Workqueue: events request_firmware_work_func
Call Trace:
<IRQ>
dump_stack+0x76/0xa0
print_address_description.constprop.0+0x16/0x200
? ath9k_hif_usb_rx_cb+0x490/0xed7 [ath9k_htc]
? ath9k_hif_usb_rx_cb+0x490/0xed7 [ath9k_htc]
__kasan_report.cold+0x37/0x7c
? ath9k_hif_usb_rx_cb+0x490/0xed7 [ath9k_htc]
kasan_report+0xe/0x20
check_memory_region+0x15a/0x1d0
memcpy+0x20/0x50
ath9k_hif_usb_rx_cb+0x490/0xed7 [ath9k_htc]
? hif_usb_mgmt_cb+0x2d9/0x2d9 [ath9k_htc]
? _raw_spin_lock_irqsave+0x7b/0xd0
? _raw_spin_trylock_bh+0x120/0x120
? __usb_unanchor_urb+0x12f/0x210
__usb_hcd_giveback_urb+0x1e4/0x380
usb_giveback_urb_bh+0x241/0x4f0
? __hrtimer_run_queues+0x316/0x740
? __usb_hcd_giveback_urb+0x380/0x380
tasklet_action_common.isra.0+0x135/0x330
__do_softirq+0x18c/0x634
irq_exit+0x114/0x140
smp_apic_timer_interrupt+0xde/0x380
apic_timer_interrupt+0xf/0x20
I found the bug using a custome USBFuzz port. It's a research work
to fuzz USB stack/drivers. I modified it to fuzz ath9k driver only,
providing hand-crafted usb descriptors to QEMU.
After fixing the value of pkt_tag to ATH_USB_RX_STREAM_MODE_TAG in QEMU
emulation, I found the KASAN report. The bug is triggerable whenever
pkt_len is above two MAX_RX_BUG_SIZE. I used the same input that crashes
to test the driver works when applying the patch.
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/YXsidrRuK6zBJicZ@10-18-43-117.dynapool.wireless.nyu.edu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0055858638 ]
When a new USB device gets plugged to nested hubs, the affected hub,
which connects to usb 2-1.4-port2, doesn't report there's any change,
hence the nested hubs go back to runtime suspend like nothing happened:
[ 281.032951] usb usb2: usb wakeup-resume
[ 281.032959] usb usb2: usb auto-resume
[ 281.032974] hub 2-0:1.0: hub_resume
[ 281.033011] usb usb2-port1: status 0263 change 0000
[ 281.033077] hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.049797] usb 2-1: usb wakeup-resume
[ 281.069800] usb 2-1: Waited 0ms for CONNECT
[ 281.069810] usb 2-1: finish resume
[ 281.070026] hub 2-1:1.0: hub_resume
[ 281.070250] usb 2-1-port4: status 0203 change 0000
[ 281.070272] usb usb2-port1: resume, status 0
[ 281.070282] hub 2-1:1.0: state 7 ports 4 chg 0010 evt 0000
[ 281.089813] usb 2-1.4: usb wakeup-resume
[ 281.109792] usb 2-1.4: Waited 0ms for CONNECT
[ 281.109801] usb 2-1.4: finish resume
[ 281.109991] hub 2-1.4:1.0: hub_resume
[ 281.110147] usb 2-1.4-port2: status 0263 change 0000
[ 281.110234] usb 2-1-port4: resume, status 0
[ 281.110239] usb 2-1-port4: status 0203, change 0000, 10.0 Gb/s
[ 281.110266] hub 2-1.4:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.110426] hub 2-1.4:1.0: hub_suspend
[ 281.110565] usb 2-1.4: usb auto-suspend, wakeup 1
[ 281.130998] hub 2-1:1.0: hub_suspend
[ 281.137788] usb 2-1: usb auto-suspend, wakeup 1
[ 281.142935] hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.177828] usb 2-1: usb wakeup-resume
[ 281.197839] usb 2-1: Waited 0ms for CONNECT
[ 281.197850] usb 2-1: finish resume
[ 281.197984] hub 2-1:1.0: hub_resume
[ 281.198203] usb 2-1-port4: status 0203 change 0000
[ 281.198228] usb usb2-port1: resume, status 0
[ 281.198237] hub 2-1:1.0: state 7 ports 4 chg 0010 evt 0000
[ 281.217835] usb 2-1.4: usb wakeup-resume
[ 281.237834] usb 2-1.4: Waited 0ms for CONNECT
[ 281.237845] usb 2-1.4: finish resume
[ 281.237990] hub 2-1.4:1.0: hub_resume
[ 281.238067] usb 2-1.4-port2: status 0263 change 0000
[ 281.238148] usb 2-1-port4: resume, status 0
[ 281.238152] usb 2-1-port4: status 0203, change 0000, 10.0 Gb/s
[ 281.238166] hub 2-1.4:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.238385] hub 2-1.4:1.0: hub_suspend
[ 281.238523] usb 2-1.4: usb auto-suspend, wakeup 1
[ 281.258076] hub 2-1:1.0: hub_suspend
[ 281.265744] usb 2-1: usb auto-suspend, wakeup 1
[ 281.285976] hub 2-0:1.0: hub_suspend
[ 281.285988] usb usb2: bus auto-suspend, wakeup 1
USB 3.2 spec, 9.2.5.4 "Changing Function Suspend State" says that "If
the link is in a non-U0 state, then the device must transition the link
to U0 prior to sending the remote wake message", but the hub only
transits the link to U0 after signaling remote wakeup.
So be more forgiving and use a 20ms delay to let the link transit to U0
for remote wakeup.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20211215120108.336597-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 521223d8b3 ]
The min and max frequency QoS requests in the cpufreq core are
initialized to whatever the current min and max frequency values are
at the init time, but if any of these values change later (for
example, cpuinfo.max_freq is updated by the driver), these initial
request values will be limiting the CPU frequency unnecessarily
unless they are changed by user space via sysfs.
To address this, initialize min_freq_req and max_freq_req to
FREQ_QOS_MIN_DEFAULT_VALUE and FREQ_QOS_MAX_DEFAULT_VALUE,
respectively, so they don't really limit anything until user
space updates them.
Reported-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1579e6119 ]
Because refcount_dec_not_one() returns true if the target refcount
becomes saturated, it is generally unsafe to use its return value as
a loop termination condition, but that is what happens when a device
link's supplier device is released during runtime PM suspend
operations and on device link removal.
To address this, introduce pm_runtime_release_supplier() to be used
in the above cases which will check the supplier device's runtime
PM usage counter in addition to the refcount_dec_not_one() return
value, so the loop can be terminated in case the rpm_active refcount
value becomes invalid, and update the code in question to use it as
appropriate.
This change is not expected to have any visible functional impact.
Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b14cbd643 ]
The Tegra186 CCPLEX cluster register region is 4 MiB is length, not 4
MiB - 1. This was likely presumed to be the "limit" rather than length.
Fix it up.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f110f5306 ]
Due to the audit control mutex necessary for serializing audit
userspace messages we haven't been able to block/penalize userspace
processes that attempt to send audit records while the system is
under audit pressure. The result is that privileged userspace
applications have a priority boost with respect to audit as they are
not bound by the same audit queue throttling as the other tasks on
the system.
This patch attempts to restore some balance to the system when under
audit pressure by blocking these privileged userspace tasks after
they have finished their audit processing, and dropped the audit
control mutex, but before they return to userspace.
Reported-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Tested-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Reviewed-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c3e5b74b9 ]
The mmc core takes a specific path to support initializing of a
non-standard SDIO card. This is triggered by looking for the card-quirk,
MMC_QUIRK_NONSTD_SDIO.
In mmc_sdio_init_card() this gets rather messy, as it causes the code to
bail out earlier, compared to the usual path. This leads to that the OCR
doesn't get saved properly in card->ocr. Fortunately, only omap_hsmmc has
been using the MMC_QUIRK_NONSTD_SDIO and is dealing with the issue, by
assigning a hardcoded value (0x80) to card->ocr from an ->init_card() ops.
To make the behaviour consistent, let's instead rely on the core to save
the OCR in card->ocr during initialization.
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Link: https://lore.kernel.org/r/e7936cff7fc24d187ef2680d3b4edb0ade58f293.1636564631.git.hns@goldelico.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3af86b0469 ]
In hexium_attach(dev, info), saa7146_vv_init() is called to allocate
a new memory for dev->vv_data. saa7146_vv_release() will be called on
failure of saa7146_register_device(). There is a dereference of
dev->vv_data in saa7146_vv_release(), which could lead to a NULL
pointer dereference on failure of saa7146_vv_init().
Fix this bug by adding a check of saa7146_vv_init().
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_VIDEO_HEXIUM_GEMINI=m show no new warnings,
and our static analyzer no longer warns about this code.
Link: https://lore.kernel.org/linux-media/20211203154030.111210-1-zhou1615@umn.edu
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8fede658e7 ]
Without this, some IR will be missing mid-stream and we might decode
something which never really occurred.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2cbad98903 ]
The WARN_ONCE() in bpf_warn_invalid_xdp_action() can be triggered by
any bugged program, and even attaching a correct program to a NIC
not supporting the given action.
The resulting splat, beyond polluting the logs, fouls automated tools:
e.g. a syzkaller reproducers using an XDP program returning an
unsupported action will never pass validation.
Replace the WARN_ONCE with a less intrusive pr_warn_once().
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/016ceec56e4817ebb2a9e35ce794d5c917df572c.1638189075.git.pabeni@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c7ce80a81 ]
And allow instrumentation inside it because it does calls to other
facilities which will not be tagged noinstr.
Fixes
vmlinux.o: warning: objtool: do_machine_check()+0xc73: call to mce_panic() leaves .noinstr.text section
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20211208111343.8130-8-bp@alien8.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5992f373c ]
Commit 32f6e5da83 ("selftests/ftrace: Add kprobe profile testcase")
added a new kprobes testcase, but has a description which does not
describe what the test case is doing and is duplicating the description
of another test case.
Therefore change the test case description, so it is unique and then
allows easily to tell which test case actually passed or failed.
Reported-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61a7904b6a ]
The gpio-aspeed driver implements an irq_chip which need to be invoked
from hardirq context. Since spin_lock() can sleep with PREEMPT_RT, it is
no longer legal to invoke it while interrupts are disabled.
This also causes lockdep to complain about:
[ 0.649797] [ BUG: Invalid wait context ]
because aspeed_gpio.lock (spin_lock_t) is taken under irq_desc.lock
(raw_spinlock_t).
Let's use of raw_spinlock_t instead of spinlock_t.
Signed-off-by: Iwona Winiarska <iwona.winiarska@intel.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f20f94f7f5 ]
The PHY settings table is supposed to be sorted by descending match
priority - in other words, earlier entries are preferred over later
entries.
The order of 1000baseKX/Full and 1000baseT/Full is such that we
prefer 1000baseKX/Full over 1000baseT/Full, but 1000baseKX/Full is
a lot rarer than 1000baseT/Full, and thus is much less likely to
be preferred.
This causes phylink problems - it means a fixed link specifying a
speed of 1G and full duplex gets an ethtool linkmode of 1000baseKX/Full
rather than 1000baseT/Full as would be expected - and since we offer
userspace a software emulation of a conventional copper PHY, we want
to offer copper modes in preference to anything else. However, we do
still want to allow the rarer modes as well.
Hence, let's reorder these two modes to prefer copper.
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/E1muvFO-00F6jY-1K@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7dac08341 ]
When updating Rx and Tx queue kobjects, the queue count should always be
updated to match the queue kobjects count. This was not done in the net
device unregistration path, fix it. Tracking all queue count updates
will allow in a following up patch to detect illegal updates.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8a91863eb ]
While running stress tests in roaming scenarios (switching ap's every 5
seconds, we discovered a issue which leads to tx hangings of exactly 5
seconds while or after scanning for new accesspoints. We found out that
this hanging is triggered by ath10k_mac_wait_tx_complete since the
empty_tx_wq was not wake when the num_tx_pending counter reaches zero.
To fix this, we simply move the wake_up call to htt_tx_dec_pending,
since this call was missed on several locations within the ath10k code.
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20210505085806.11474-1-s.gottschall@dd-wrt.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db66abeea3 ]
If userspace installs a lot of multicast groups very quickly, then
we may run out of command queue space as we send the updates in an
asynchronous fashion (due to locking concerns), and the CPU can
create them faster than the firmware can process them. This is true
even when mac80211 has a work struct that gets scheduled.
Fix this by synchronizing with the firmware after sending all those
commands - outside of the iteration we can send a synchronous echo
command that just has the effect of the CPU waiting for the prior
asynchronous commands to finish. This also will cause fewer of the
commands to be sent to the firmware overall, because the work will
only run once when rescheduled multiple times while it's running.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=213649
Suggested-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reported-by: Maximilian Ernestus <maximilian@ernestus.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211204083238.51aea5b79ea4.I88a44798efda16e9fe480fb3e94224931d311b29@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3380cac0c ]
If protocol tunnels are already up when the driver is loaded, for
instance if the boot firmware implements connection manager of its own,
runtime PM reference count of the consumer devices behind the tunnel
might have been increased already before the device link is created but
the supplier device runtime PM reference count is not. This leads to a
situation where the supplier (the Thunderbolt driver) can runtime
suspend even if it should not because the corresponding protocol tunnel
needs to be up causing the devices to be removed from the corresponding
native bus.
Prevent this from happening by making both sides of the link runtime PM
active briefly. The pm_runtime_put() for the consumer (PCIe
root/downstream port, xHCI) then allows it to runtime suspend again but
keeps the supplier runtime resumed the whole time it is runtime active.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 348df80353 ]
In hexium_attach(dev, info), saa7146_vv_init() is called to allocate
a new memory for dev->vv_data. In hexium_detach(), saa7146_vv_release()
will be called and there is a dereference of dev->vv_data in
saa7146_vv_release(), which could lead to a NULL pointer dereference
on failure of saa7146_vv_init() according to the following logic.
Both hexium_attach() and hexium_detach() are callback functions of
the variable 'extension', so there exists a possible call chain directly
from hexium_attach() to hexium_detach():
hexium_attach(dev, info) -- fail to alloc memory to dev->vv_data
| in saa7146_vv_init().
|
|
hexium_detach() -- a dereference of dev->vv_data in saa7146_vv_release()
Fix this bug by adding a check of saa7146_vv_init().
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_VIDEO_HEXIUM_ORION=m show no new warnings,
and our static analyzer no longer warns about this code.
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da6911f330 ]
This change fixes two issues with the size constraints for buffers.
- There is no width alignment constraint for RGB formats. Prior to this
change they were treated as YUV and as a result were more restricted
than needed. Add a new check to differentiate between the two.
- The minimum width and height supported is 5x2, not 2x4, this is an
artifact from the driver's soc-camera days. Fix this incorrect
assumption.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8ed7d2f61 ]
Some uvc devices appear to require the maximum allowed USB timeout
for GET_CUR/SET_CUR requests.
So lets just bump the UVC control timeout to 5 seconds which is the
same as the usb ctrl get/set defaults:
USB_CTRL_GET_TIMEOUT 5000
USB_CTRL_SET_TIMEOUT 5000
It fixes the following runtime warnings:
Failed to query (GET_CUR) UVC control 11 on unit 2: -110 (exp. 1).
Failed to query (SET_CUR) UVC control 3 on unit 2: -110 (exp. 2).
Signed-off-by: James Hilliard <james.hilliard1@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f0ce591dc9 ]
When the CMM is enabled, an offset of 25 pixels must be subtracted from
the HDS (horizontal display start) and HDE (horizontal display end)
registers. Fix the timings calculation, and take this into account in
the mode validation.
This fixes a visible horizontal offset in the image with VGA monitors.
HDMI monitors seem to be generally more tolerant to incorrect timings,
but may be affected too.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71d5049b05 ]
Move the switching code into a function so that it can be re-used and
add a global TLB flush. This makes sure that usage of memory which is
not mapped in the trampoline page-table is reliably caught.
Also move the clearing of CR4.PCIDE before the CR3 switch because the
cr4_clear_bits() function will access data not mapped into the
trampoline page-table.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20211202153226.22946-4-joro@8bytes.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57d2dbf710 ]
The GPD win and its sibling the GPD pocket (99% the same electronics in a
different case) use a PCI wifi card. But the ACPI tables on both variants
contain a bug where the SDIO MMC controller for SDIO wifi cards is enabled
despite this. This SDIO MMC controller has a PCI0.SDHB.BRC1 child-device
which _PS3 method sets a GPIO causing the PCI wifi card to turn off.
At the moment there is a pretty ugly kludge in the sdhci-acpi.c code,
just to work around the bug in the DSDT of this single design. This can
be solved cleaner/simply with a quirk overriding the _STA return of the
broken PCI0.SDHB.BRC1 PCI0.SDHB.BRC1 child with a status value of 0,
so that its power_manageable flag gets cleared, avoiding this problem.
Note that even though it is not used, the _STA method for the MMC
controller is deliberately not overridden. If the status of the MMC
controller were forced to 0 it would never get suspended, which would
cause these mini-laptops to not reach S0i3 level when suspended.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba46e42e92 ]
Not all ACPI-devices have a HID + UID, allow specifying quirks for
acpi_device_override_status() by path too.
Note this moves the path/HID+UID check to after the CPU + DMI checks
since the path lookup is somewhat costly.
This way this lookup is only done on devices where the other checks
match.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a68b346a2 ]
Currently, acpi_bus_get_status() calls acpi_device_always_present() to
allow platform quirks to override the _STA return to report that a
device is present (status = ACPI_STA_DEFAULT) independent of the _STA
return.
In some cases it might also be useful to have the opposite functionality
and have a platform quirk which marks a device as not present (status = 0)
to work around ACPI table bugs.
Change acpi_device_always_present() into a more generic
acpi_device_override_status() function to allow this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d431dfb764 ]
It turns out that there is a WMI object which controls the PWM2 device
used for the keyboard backlight and that WMI object also provides some
other useful functionality.
The upcoming lenovo-yogabook-wmi driver will offer both backlight
control and the other functionality, so there no longer is a need
to have the lpss-pwm driver binding to PWM2 for backlight control;
and this is now actually undesirable because this will cause both
the WMI code and the lpss-pwm driver to poke at the same PWM
controller.
Drop the always-present quirk for the PWM2 ACPI-device, so that the
lpss-pwm controller will no longer bind to it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a93789ae54 ]
Currently 'ar' reference is not added in skb_cb during
WMI mgmt tx. Though this is generally not used during tx completion
callbacks, on interface removal the remaining idr cleanup callback
uses the ar ptr from skb_cb from mgmt txmgmt_idr. Hence
fill them during tx call for proper usage.
Also free the skb which is missing currently in these
callbacks.
Crash_info:
[19282.489476] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[19282.489515] pgd = 91eb8000
[19282.496702] [00000000] *pgd=00000000
[19282.502524] Internal error: Oops: 5 [#1] PREEMPT SMP ARM
[19282.783728] PC is at ath11k_mac_vif_txmgmt_idr_remove+0x28/0xd8 [ath11k]
[19282.789170] LR is at idr_for_each+0xa0/0xc8
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00729-QCAHKSWPL_SILICONZ-3 v2
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1637832614-13831-1-git-send-email-quic_srirrama@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1cb3476e4 ]
rsi_get_* functions rely on an offset variable from usb
input. The size of usb input is RSI_MAX_RX_USB_PKT_SIZE(3000),
while 2-byte offset can be up to 0xFFFF. Thus a large offset
can cause out-of-bounds read.
The patch adds a bound checking condition when rcv_pkt_len is 0,
indicating it's USB. It's unclear whether this is triggerable
from other type of bus. The following check might help in that case.
offset > rcv_pkt_len - FRAME_DESC_SZ
The bug is trigerrable with conpromised/malfunctioning USB devices.
I tested the patch with the crashing input and got no more bug report.
Attached is the KASAN report from fuzzing.
BUG: KASAN: slab-out-of-bounds in rsi_read_pkt+0x42e/0x500 [rsi_91x]
Read of size 2 at addr ffff888019439fdb by task RX-Thread/227
CPU: 0 PID: 227 Comm: RX-Thread Not tainted 5.6.0 #66
Call Trace:
dump_stack+0x76/0xa0
print_address_description.constprop.0+0x16/0x200
? rsi_read_pkt+0x42e/0x500 [rsi_91x]
? rsi_read_pkt+0x42e/0x500 [rsi_91x]
__kasan_report.cold+0x37/0x7c
? rsi_read_pkt+0x42e/0x500 [rsi_91x]
kasan_report+0xe/0x20
rsi_read_pkt+0x42e/0x500 [rsi_91x]
rsi_usb_rx_thread+0x1b1/0x2fc [rsi_usb]
? rsi_probe+0x16a0/0x16a0 [rsi_usb]
? _raw_spin_lock_irqsave+0x7b/0xd0
? _raw_spin_trylock_bh+0x120/0x120
? __wake_up_common+0x10b/0x520
? rsi_probe+0x16a0/0x16a0 [rsi_usb]
kthread+0x2b5/0x3b0
? kthread_create_on_node+0xd0/0xd0
ret_from_fork+0x22/0x40
Reported-by: Brendan Dolan-Gavitt <brendandg@nyu.edu>
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YXxXS4wgu2OsmlVv@10-18-43-117.dynapool.wireless.nyu.edu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b07e3c6ebc ]
When freeing rx_cb->rx_skb, the pointer is not set to NULL,
a later rsi_rx_done_handler call will try to read the freed
address.
This bug will very likley lead to double free, although
detected early as use-after-free bug.
The bug is triggerable with a compromised/malfunctional usb
device. After applying the patch, the same input no longer
triggers the use-after-free.
Attached is the kasan report from fuzzing.
BUG: KASAN: use-after-free in rsi_rx_done_handler+0x354/0x430 [rsi_usb]
Read of size 4 at addr ffff8880188e5930 by task modprobe/231
Call Trace:
<IRQ>
dump_stack+0x76/0xa0
print_address_description.constprop.0+0x16/0x200
? rsi_rx_done_handler+0x354/0x430 [rsi_usb]
? rsi_rx_done_handler+0x354/0x430 [rsi_usb]
__kasan_report.cold+0x37/0x7c
? dma_direct_unmap_page+0x90/0x110
? rsi_rx_done_handler+0x354/0x430 [rsi_usb]
kasan_report+0xe/0x20
rsi_rx_done_handler+0x354/0x430 [rsi_usb]
__usb_hcd_giveback_urb+0x1e4/0x380
usb_giveback_urb_bh+0x241/0x4f0
? __usb_hcd_giveback_urb+0x380/0x380
? apic_timer_interrupt+0xa/0x20
tasklet_action_common.isra.0+0x135/0x330
__do_softirq+0x18c/0x634
? handle_irq_event+0xcd/0x157
? handle_edge_irq+0x1eb/0x7b0
irq_exit+0x114/0x140
do_IRQ+0x91/0x1e0
common_interrupt+0xf/0xf
</IRQ>
Reported-by: Brendan Dolan-Gavitt <brendandg@nyu.edu>
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YXxQL/vIiYcZUu/j@10-18-43-117.dynapool.wireless.nyu.edu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04d80663f6 ]
Currently, with an unknown recv_type, mwifiex_usb_recv
just return -1 without restoring the skb. Next time
mwifiex_usb_rx_complete is invoked with the same skb,
calling skb_put causes skb_over_panic.
The bug is triggerable with a compromised/malfunctioning
usb device. After applying the patch, skb_over_panic
no longer shows up with the same input.
Attached is the panic report from fuzzing.
skbuff: skb_over_panic: text:000000003bf1b5fa
len:2048 put:4 head:00000000dd6a115b data:000000000a9445d8
tail:0x844 end:0x840 dev:<NULL>
kernel BUG at net/core/skbuff.c:109!
invalid opcode: 0000 [#1] SMP KASAN NOPTI
CPU: 0 PID: 198 Comm: in:imklog Not tainted 5.6.0 #60
RIP: 0010:skb_panic+0x15f/0x161
Call Trace:
<IRQ>
? mwifiex_usb_rx_complete+0x26b/0xfcd [mwifiex_usb]
skb_put.cold+0x24/0x24
mwifiex_usb_rx_complete+0x26b/0xfcd [mwifiex_usb]
__usb_hcd_giveback_urb+0x1e4/0x380
usb_giveback_urb_bh+0x241/0x4f0
? __hrtimer_run_queues+0x316/0x740
? __usb_hcd_giveback_urb+0x380/0x380
tasklet_action_common.isra.0+0x135/0x330
__do_softirq+0x18c/0x634
irq_exit+0x114/0x140
smp_apic_timer_interrupt+0xde/0x380
apic_timer_interrupt+0xf/0x20
</IRQ>
Reported-by: Brendan Dolan-Gavitt <brendandg@nyu.edu>
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YX4CqjfRcTa6bVL+@Zekuns-MBP-16.fios-router.home
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 552d03a223 ]
The APT compares the current time stamp with a pre-set value. The
current code only considered the 4 LSB only. Yet, after reviews by
mathematicians of the user space Jitter RNG version >= 3.1.0, it was
concluded that the APT can be calculated on the 32 LSB of the time
delta. Thi change is applied to the kernel.
This fixes a bug where an AMD EPYC fails this test as its RDTSC value
contains zeros in the LSB. The most appropriate fix would have been to
apply a GCD calculation and divide the time stamp by the GCD. Yet, this
is a significant code change that will be considered for a future
update. Note, tests showed that constantly the GCD always was 32 on
these systems, i.e. the 5 LSB were always zero (thus failing the APT
since it only considered the 4 LSB for its calculation).
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1ee1c08fc ]
cl is freed on error of calling device_register, but this
object is return later, which will cause uaf issue. Fix it
by return NULL on error.
Signed-off-by: Chengfeng Ye <cyeaa@connect.ust.hk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bdfd6ab8fd ]
If the IRQ is already in use, then acpi_dev_gpio_irq_get_by() really
should not change the type underneath the current owner.
I specifically hit an issue with this an a Chuwi Hi8 Super (CWI509) Bay
Trail tablet, when the Boot OS selection in the BIOS is set to Android.
In this case _STA for a MAX17047 ACPI I2C device wrongly returns 0xf and
the _CRS resources for this device include a GpioInt pointing to a GPIO
already in use by an _AEI handler, with a different type then specified
in the _CRS for the MAX17047 device. Leading to the acpi_dev_gpio_irq_get()
call done by the i2c-core-acpi.c code changing the type breaking the
_AEI handler.
Now this clearly is a bug in the DSDT of this tablet (in Android mode),
but in general calling irq_set_irq_type() on an IRQ which already is
in use seems like a bad idea.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 028e083832 ]
The UCR4_OREN should be disabled before disabling the uart receiver in
.stop_rx() instead of in the .shutdown().
Otherwise, if we have the overrun error during the receiver disable
process, the overrun interrupt will keep trigging until we disable the
OREN interrupt in the .shutdown(), because the ORE status can only be
cleared when read the rx FIFO or reset the controller. Although the
called time between the receiver disable and OREN disable in .shutdown()
is very short, there is still the risk of endless interrupt during this
short period of time. So here change to disable OREN before the receiver
been disabled in .stop_rx().
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20211125020349.4980-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1020d3cf4 ]
On an arm64 platform with the Spectrum ASIC, after loading and executing
a new kernel via kexec, the following trace [1] is observed. This seems
to be caused by the fact that the device is not properly shutdown before
executing the new kernel.
Fix this by implementing a shutdown method which mirrors the remove
method, as recommended by the kexec maintainer [2][3].
[1]
BUG: Bad page state in process devlink pfn:22f73d
page:fffffe00089dcf40 refcount:-1 mapcount:0 mapping:0000000000000000 index:0x0
flags: 0x2ffff00000000000()
raw: 2ffff00000000000 0000000000000000 ffffffff089d0201 0000000000000000
raw: 0000000000000000 0000000000000000 ffffffffffffffff 0000000000000000
page dumped because: nonzero _refcount
Modules linked in:
CPU: 1 PID: 16346 Comm: devlink Tainted: G B 5.8.0-rc6-custom-273020-gac6b365b1bf5 #44
Hardware name: Marvell Armada 7040 TX4810M (DT)
Call trace:
dump_backtrace+0x0/0x1d0
show_stack+0x1c/0x28
dump_stack+0xbc/0x118
bad_page+0xcc/0xf8
check_free_page_bad+0x80/0x88
__free_pages_ok+0x3f8/0x418
__free_pages+0x38/0x60
kmem_freepages+0x200/0x2a8
slab_destroy+0x28/0x68
slabs_destroy+0x60/0x90
___cache_free+0x1b4/0x358
kfree+0xc0/0x1d0
skb_free_head+0x2c/0x38
skb_release_data+0x110/0x1a0
skb_release_all+0x2c/0x38
consume_skb+0x38/0x130
__dev_kfree_skb_any+0x44/0x50
mlxsw_pci_rdq_fini+0x8c/0xb0
mlxsw_pci_queue_fini.isra.0+0x28/0x58
mlxsw_pci_queue_group_fini+0x58/0x88
mlxsw_pci_aqs_fini+0x2c/0x60
mlxsw_pci_fini+0x34/0x50
mlxsw_core_bus_device_unregister+0x104/0x1d0
mlxsw_devlink_core_bus_device_reload_down+0x2c/0x48
devlink_reload+0x44/0x158
devlink_nl_cmd_reload+0x270/0x290
genl_rcv_msg+0x188/0x2f0
netlink_rcv_skb+0x5c/0x118
genl_rcv+0x3c/0x50
netlink_unicast+0x1bc/0x278
netlink_sendmsg+0x194/0x390
__sys_sendto+0xe0/0x158
__arm64_sys_sendto+0x2c/0x38
el0_svc_common.constprop.0+0x70/0x168
do_el0_svc+0x28/0x88
el0_sync_handler+0x88/0x190
el0_sync+0x140/0x180
[2]
https://www.mail-archive.com/linux-kernel@vger.kernel.org/msg1195432.html
[3]
https://patchwork.kernel.org/project/linux-scsi/patch/20170212214920.28866-1-anton@ozlabs.org/#20116693
Cc: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a689e8d1f8 ]
Clang static analysis reports this error
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:2870:7: warning:
Dereference of null pointer [clang-analyzer-core.NullDereference]
if
(top_pipe_to_program->stream_res.tg->funcs->lock_doublebuffer_enable) {
^
top_pipe_to_program being NULL is caught as an error
But then it is used to report the error.
So add a check before using it.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0100bce4f ]
Since commit 4b563a0666 ("ARM: imx: Remove imx21 support"), the config
DEBUG_IMX21_IMX27_UART is really only debug support for IMX27.
So, rename this option to DEBUG_IMX27_UART and adjust dependencies in
Kconfig and rename the definitions to IMX27 as further clean-up.
This issue was discovered with ./scripts/checkkconfigsymbols.py, which
reported that DEBUG_IMX21_IMX27_UART depends on the non-existing config
SOC_IMX21.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5fe7864d8 ]
When a keyboard without a function key is detected, instead of removing
all quirks, remove only the APPLE_HAS_FN quirk.
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c76ef96fc0 ]
Function fs endpoint file operations are synchronized via an interruptible
mutex wait. However we see threads that do ep file operations concurrently
are getting blocked for the mutex lock in __fdget_pos(). This is an
uninterruptible wait and we see hung task warnings and kernel panic
if hung_task_panic systcl is enabled if host does not send/receive
the data for long time.
The reason for threads getting blocked in __fdget_pos() is due to
the file position protection introduced by the commit 9c225f2655
("vfs: atomic f_pos accesses as per POSIX"). Since function fs
endpoint files does not have the notion of the file position, switch
to the stream mode. This will bypass the file position mutex and
threads will be blocked in interruptible state for the function fs
mutex.
It should not affects user space as we are only changing the task state
changes the task state from UNINTERRUPTIBLE to INTERRUPTIBLE while waiting
for the USB transfers to be finished. However there is a slight change to
the O_NONBLOCK behavior. Earlier threads that are using O_NONBLOCK are also
getting blocked inside fdget_pos(). Now they reach to function fs and error
code is returned. The non blocking behavior is actually honoured now.
Reviewed-by: John Keeping <john@metanate.com>
Signed-off-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Link: https://lore.kernel.org/r/1636712682-1226-1-git-send-email-quic_pkondeti@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58043dbf6d ]
The succ var tracks memory allocation erros on this function.
Fix it, in order to stop this W=1 Werror in clang:
drivers/staging/media/atomisp/pci/sh_css_params.c:2430:7: error: variable 'succ' set but not used [-Werror,-Wunused-but-set-variable]
bool succ = true;
^
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9057d6c23e ]
Currently, creating a batman-adv interface in an unprivileged LXD
container and attaching secondary interfaces to it with "ip" or "batctl"
works fine. However all batctl debug and configuration commands
fail:
root@container:~# batctl originators
Error received: Operation not permitted
root@container:~# batctl orig_interval
1000
root@container:~# batctl orig_interval 2000
root@container:~# batctl orig_interval
1000
To fix this change the generic netlink permissions from GENL_ADMIN_PERM
to GENL_UNS_ADMIN_PERM. This way a batman-adv interface is fully
maintainable as root from within a user namespace, from an unprivileged
container.
All except one batman-adv netlink setting are per interface and do not
leak information or change settings from the host system and are
therefore save to retrieve or modify as root from within an unprivileged
container.
"batctl routing_algo" / BATADV_CMD_GET_ROUTING_ALGOS is the only
exception: It provides the batman-adv kernel module wide default routing
algorithm. However it is read-only from netlink and an unprivileged
container is still not allowed to modify
/sys/module/batman_adv/parameters/routing_algo. Instead it is advised to
use the newly introduced "batctl if create routing_algo RA_NAME" /
IFLA_BATADV_ALGO_NAME to set the routing algorithm on interface
creation, which already works fine in an unprivileged container.
Cc: Tycho Andersen <tycho@tycho.pizza>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 85744f2d93 ]
Fix following coccicheck warning:
./arch/arm/mach-shmobile/regulator-quirk-rcar-gen2.c:156:1-33: Function
for_each_matching_node_and_match should have of_node_put() before break
and goto.
Early exits from for_each_matching_node_and_match() should decrement the
node reference counter.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Link: https://lore.kernel.org/r/20211018014503.7598-1-wanjiabing@vivo.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c45e343c5 ]
The atomisp driver originally used the s_parm command to
initialize the run_mode type to the driver. So, before start
setting up the streaming, s_parm should be called.
So, even having 5 "normal" video devices, one meant to be used
for each type, the run_mode was actually selected when
s_parm is called.
Without setting the run mode, applications that don't call
VIDIOC_SET_PARM with a custom atomisp parameters won't work, as
the pipeline won't be set:
atomisp-isp2 0000:00:03.0: can't create streams
atomisp-isp2 0000:00:03.0: __get_frame_info 1600x1200 (padded to 0) returned -22
However, commit 8a7c5594c0 ("media: v4l2-ioctl: clear fields in s_parm")
broke support for it, with a good reason, as drivers shoudn't be
extending the API for their own purposes.
So, as an step to allow generic apps to use this driver, put
the device's run_mode in preview after open.
After this patch, using v4l2grab starts to work on preview
mode (/dev/video2):
$ v4l2grab -f YUYV -x 1600 -y 1200 -d /dev/video2 -n 1 -u
$ feh out000.pnm
So, let's just setup the default run_mode that each video devnode
should assume, setting it at open() time.
Reported-by: Tsuchiya Yuto <kitakar@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9e9094c4e ]
The internal try_fmt logic is not meant to provide everything
that the V4L2 API should provide. Also, it doesn't decrement
the pads that are used only internally by the driver, but aren't
part of the device's output.
Fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d2271d2fb ]
There have been reports of the WFI timing out on some boards, and a
patch was proposed to just remove it. This stuff is rather fragile,
and I believe the WFI might be needed with our FW prior to GM200.
However, we probably should not be touching PMU during init on GPUs
where we depend on NVIDIA FW, outside of limited circumstances, so
this should be a somewhat safer change that achieves the desired
result.
Reported-by: Diego Viola <diego.viola@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Link: https://gitlab.freedesktop.org/drm/nouveau/-/merge_requests/10
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f2532d65a ]
The current ELD handling takes the internal connector ELD buffer and
shares it to the I2S and AHB sub-driver.
But with DRM_BRIDGE_ATTACH_NO_CONNECTOR, the connector is created
elsewhere (or not), and an eventual connector is known only
if the bridge chain up to a connector is enabled.
The current dw-hdmi code gets the current connector from
atomic_enable() so use the already stored connector pointer and
replace the buffer pointer with a callback returning the current
connector ELD buffer.
Since a connector is not always available, either pass an empty
ELD to the alsa HDMI driver or don't call snd_pcm_hw_constraint_eld()
in AHB driver.
Reported-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: fixed typo in commit log]
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211029135947.3022875-1-narmstrong@baylibre.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae80b60338 ]
Unexpected WDCMSG_TARGET_START replay can lead to null-ptr-deref
when ar->tx_cmd->odata is NULL. The patch adds a null check to
prevent such case.
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
ar5523_cmd+0x46a/0x581 [ar5523]
ar5523_probe.cold+0x1b7/0x18da [ar5523]
? ar5523_cmd_rx_cb+0x7a0/0x7a0 [ar5523]
? __pm_runtime_set_status+0x54a/0x8f0
? _raw_spin_trylock_bh+0x120/0x120
? pm_runtime_barrier+0x220/0x220
? __pm_runtime_resume+0xb1/0xf0
usb_probe_interface+0x25b/0x710
really_probe+0x209/0x5d0
driver_probe_device+0xc6/0x1b0
device_driver_attach+0xe2/0x120
I found the bug using a custome USBFuzz port. It's a research work
to fuzz USB stack/drivers. I modified it to fuzz ath9k driver only,
providing hand-crafted usb descriptors to QEMU.
After fixing the code (fourth byte in usb packet) to WDCMSG_TARGET_START,
I got the null-ptr-deref bug. I believe the bug is triggerable whenever
cmd->odata is NULL. After patching, I tested with the same input and no
longer see the KASAN report.
This was NOT tested on a real device.
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YXsmPQ3awHFLuAj2@10-18-43-117.dynapool.wireless.nyu.edu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c2e3bf68f ]
This patch fixes the following crash by receiving a invalid message:
[ 160.672220] ==================================================================
[ 160.676206] BUG: KASAN: user-memory-access in dlm_user_add_ast+0xc3/0x370
[ 160.679659] Read of size 8 at addr 00000000deadbeef by task kworker/u32:13/319
[ 160.681447]
[ 160.681824] CPU: 10 PID: 319 Comm: kworker/u32:13 Not tainted 5.14.0-rc2+ #399
[ 160.683472] Hardware name: Red Hat KVM/RHEL-AV, BIOS 1.14.0-1.module+el8.6.0+12648+6ede71a5 04/01/2014
[ 160.685574] Workqueue: dlm_recv process_recv_sockets
[ 160.686721] Call Trace:
[ 160.687310] dump_stack_lvl+0x56/0x6f
[ 160.688169] ? dlm_user_add_ast+0xc3/0x370
[ 160.689116] kasan_report.cold.14+0x116/0x11b
[ 160.690138] ? dlm_user_add_ast+0xc3/0x370
[ 160.690832] dlm_user_add_ast+0xc3/0x370
[ 160.691502] _receive_unlock_reply+0x103/0x170
[ 160.692241] _receive_message+0x11df/0x1ec0
[ 160.692926] ? rcu_read_lock_sched_held+0xa1/0xd0
[ 160.693700] ? rcu_read_lock_bh_held+0xb0/0xb0
[ 160.694427] ? lock_acquire+0x175/0x400
[ 160.695058] ? do_purge.isra.51+0x200/0x200
[ 160.695744] ? lock_acquired+0x360/0x5d0
[ 160.696400] ? lock_contended+0x6a0/0x6a0
[ 160.697055] ? lock_release+0x21d/0x5e0
[ 160.697686] ? lock_is_held_type+0xe0/0x110
[ 160.698352] ? lock_is_held_type+0xe0/0x110
[ 160.699026] ? ___might_sleep+0x1cc/0x1e0
[ 160.699698] ? dlm_wait_requestqueue+0x94/0x140
[ 160.700451] ? dlm_process_requestqueue+0x240/0x240
[ 160.701249] ? down_write_killable+0x2b0/0x2b0
[ 160.701988] ? do_raw_spin_unlock+0xa2/0x130
[ 160.702690] dlm_receive_buffer+0x1a5/0x210
[ 160.703385] dlm_process_incoming_buffer+0x726/0x9f0
[ 160.704210] receive_from_sock+0x1c0/0x3b0
[ 160.704886] ? dlm_tcp_shutdown+0x30/0x30
[ 160.705561] ? lock_acquire+0x175/0x400
[ 160.706197] ? rcu_read_lock_sched_held+0xa1/0xd0
[ 160.706941] ? rcu_read_lock_bh_held+0xb0/0xb0
[ 160.707681] process_recv_sockets+0x32/0x40
[ 160.708366] process_one_work+0x55e/0xad0
[ 160.709045] ? pwq_dec_nr_in_flight+0x110/0x110
[ 160.709820] worker_thread+0x65/0x5e0
[ 160.710423] ? process_one_work+0xad0/0xad0
[ 160.711087] kthread+0x1ed/0x220
[ 160.711628] ? set_kthread_struct+0x80/0x80
[ 160.712314] ret_from_fork+0x22/0x30
The issue is that we received a DLM message for a user lock but the
destination lock is a kernel lock. Note that the address which is trying
to derefence is 00000000deadbeef, which is in a kernel lock
lkb->lkb_astparam, this field should never be derefenced by the DLM
kernel stack. In case of a user lock lkb->lkb_astparam is lkb->lkb_ua
(memory is shared by a union field). The struct lkb_ua will be handled
by the DLM kernel stack but on a kernel lock it will contain invalid
data and ends in most likely crashing the kernel.
It can be reproduced with two cluster nodes.
node 2:
dlm_tool join test
echo "862 fooobaar 1 2 1" > /sys/kernel/debug/dlm/test_locks
echo "862 3 1" > /sys/kernel/debug/dlm/test_waiters
node 1:
dlm_tool join test
python:
foo = DLM(h_cmd=3, o_nextcmd=1, h_nodeid=1, h_lockspace=0x77222027, \
m_type=7, m_flags=0x1, m_remid=0x862, m_result=0xFFFEFFFE)
newFile = open("/sys/kernel/debug/dlm/comms/2/rawmsg", "wb")
newFile.write(bytes(foo))
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a4bb6a8e9 ]
Fault injection test report debugfs entry leak as follows:
debugfs: Directory 'hci0' with parent 'bluetooth' already present!
When register_pm_notifier() failed in hci_register_dev(), the debugfs
create by debugfs_create_dir() do not removed in the error handing path.
Add the remove debugfs code to fix it.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e9af026a3b ]
Since the LED multicolor framework support was added in commit
92a81562e6 ("leds: lp55xx: Add multicolor framework support to lp55xx")
LEDs on this platform stopped working.
Fixes: 92a81562e6 ("leds: lp55xx: Add multicolor framework support to lp55xx")
Fixes: ac219bf3c9 ("leds: lp55xx: Convert to use GPIO descriptors")
Signed-off-by: Merlijn Wajer <merlijn@wizzup.org>
Signed-off-by: Sicelo A. Mhlongo <absicsz@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c861c1be38 ]
bm1880_clk_unregister_pll & bm1880_clk_unregister_div both try to
free statically allocated variables, so remove those kfrees.
For example, if we take L703 kfree(div_hw):
- div_hw is a bm1880_div_hw_clock pointer
- in bm1880_clk_register_plls this is pointed to an element of arg1:
struct bm1880_div_hw_clock *clks
- in the probe, where bm1880_clk_register_plls is called arg1 is
bm1880_div_clks, defined on L371:
static struct bm1880_div_hw_clock bm1880_div_clks[]
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Fixes: 1ab4601da5 ("clk: Add common clock driver for BM1880 SoC")
Link: https://lore.kernel.org/r/20211223154244.1024062-1-conor.dooley@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3203863434 ]
According to RM, the clock divider range is from 1 to 8, clock
prescaling ratio may be any power of 2 from 1 to 128.
So the supported divider is not all the value between
1 and 1024, just limited value in that range.
Create table for the supported divder and add function to
check the clock divider is available by comparing with
the table.
Fixes: d0250cf4f2 ("ASoC: fsl_asrc: Add an option to select internal ratio mode")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1641380883-20709-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f03055d50 ]
The MIPS BMC63XX subarch does not provide/support clk_set_parent().
This causes build errors in a few drivers, so add a simple implementation
of that function so that callers of it will build without errors.
Fixes these build errors:
ERROR: modpost: "clk_set_parent" [sound/soc/jz4740/snd-soc-jz4740-i2s.ko] undefined!
ERROR: modpost: "clk_set_parent" [sound/soc/atmel/snd-soc-atmel-i2s.ko] undefined!
Fixes: e7300d04bd ("MIPS: BCM63xx: Add support for the Broadcom BCM63xx family of SOCs." )
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48f6e19503 ]
As per the HDA binding doc reorder {clock,reset}-names entries for
Tegra194. This also serves as a preparation for converting existing
binding doc to json-schema.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 01f68f067d ]
Currently, the STM32 LP Timer counter driver registers into both IIO and
counter subsystems, which is redundant.
Remove the IIO counter ABI and IIO registration from the STM32 LP Timer
counter driver since it's been superseded by the Counter subsystem
as discussed in [1].
Keep only the counter subsystem related part.
Move a part of the ABI documentation into a driver comment.
This also removes a duplicate ABI warning
$ scripts/get_abi.pl validate
...
/sys/bus/iio/devices/iio:deviceX/in_count0_preset is defined 2 times:
./Documentation/ABI/testing/sysfs-bus-iio-timer-stm32:100
./Documentation/ABI/testing/sysfs-bus-iio-lptimer-stm32:0
[1] https://lkml.org/lkml/2021/1/19/347
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/1611926542-2490-1-git-send-email-fabrice.gasnier@foss.st.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fcee5ce50b ]
When firmware load failed, kernel report task hung as follows:
INFO: task xrun:5191 blocked for more than 147 seconds.
Tainted: G W 5.16.0-rc5-next-20211220+ #11
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:xrun state:D stack: 0 pid: 5191 ppid: 270 flags:0x00000004
Call Trace:
__schedule+0xc12/0x4b50 kernel/sched/core.c:4986
schedule+0xd7/0x260 kernel/sched/core.c:6369 (discriminator 1)
schedule_timeout+0x7aa/0xa80 kernel/time/timer.c:1857
wait_for_completion+0x181/0x290 kernel/sched/completion.c:85
lattice_ecp3_remove+0x32/0x40 drivers/misc/lattice-ecp3-config.c:221
spi_remove+0x72/0xb0 drivers/spi/spi.c:409
lattice_ecp3_remove() wait for signals from firmware loading, but when
load failed, firmware_load() does not send this signal. This cause
device remove hung. Fix it by sending signal even if load failed.
Fixes: 781551df57 ("misc: Add Lattice ECP3 FPGA configuration via SPI")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20211228125522.3122284-1-weiyongjun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e1fcab00a ]
John Garry reported a deadlock that occurs when trying to access a
runtime-suspended SATA device. For obscure reasons, the rescan procedure
causes the link to be hard-reset, which disconnects the device.
The rescan tries to carry out a runtime resume when accessing the device.
scsi_rescan_device() holds the SCSI device lock and won't release it until
it can put commands onto the device's block queue. This can't happen until
the queue is successfully runtime-resumed or the device is unregistered.
But the runtime resume fails because the device is disconnected, and
__scsi_remove_device() can't do the unregistration because it can't get the
device lock.
The best way to resolve this deadlock appears to be to allow the block
queue to start running again even after an unsuccessful runtime resume.
The idea is that the driver or the SCSI error handler will need to be able
to use the queue to resolve the runtime resume failure.
This patch removes the err argument to blk_post_runtime_resume() and makes
the routine act as though the resume was successful always. This fixes the
deadlock.
Link: https://lore.kernel.org/r/1639999298-244569-4-git-send-email-chenxiang66@hisilicon.com
Fixes: e27829dc92 ("scsi: serialize ->rescan against ->remove")
Reported-and-tested-by: John Garry <john.garry@huawei.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7061627d7 ]
It turns out to be possible for hotplugging out a device to reach the
stage of tearing down the device's group and default domain before the
domain's flush queue has drained naturally. At this point, it is then
possible for the timeout to expire just before the del_timer() call
in free_iova_flush_queue(), such that we then proceed to free the FQ
resources while fq_flush_timeout() is still accessing them on another
CPU. Crashes due to this have been observed in the wild while removing
NVMe devices.
Close the race window by using del_timer_sync() to safely wait for any
active timeout handler to finish before we start to free things. We
already avoid any locking in free_iova_flush_queue() since the FQ is
supposed to be inactive anyway, so the potential deadlock scenario does
not apply.
Fixes: 9a005a800a ("iommu/iova: Add flush timer")
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
[ rm: rewrite commit message ]
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/0a365e5b07f14b7344677ad6a9a734966a8422ce.1639753638.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a670c82d9c ]
Commit d4a451d5fc ("arch: remove the ARCH_PHYS_ADDR_T_64BIT config
symbol") removes config ARCH_PHYS_ADDR_T_64BIT with all instances of that
config refactored appropriately. Since then, it is recommended to use the
config PHYS_ADDR_T_64BIT instead.
Commit 171543e752 ("MIPS: Disallow CPU_SUPPORTS_HUGEPAGES for XPA,EVA")
introduces the expression "!(32BIT && (ARCH_PHYS_ADDR_T_64BIT || EVA))"
for config CPU_SUPPORTS_HUGEPAGES, which unintentionally refers to the
non-existing symbol ARCH_PHYS_ADDR_T_64BIT instead of the intended
PHYS_ADDR_T_64BIT.
Fix this Kconfig reference to the intended PHYS_ADDR_T_64BIT.
This issue was identified with the script ./scripts/checkkconfigsymbols.py.
I then reported it on the mailing list and Paul confirmed the mistake in
the linked email thread.
Link: https://lore.kernel.org/lkml/H8IU3R.H5QVNRA077PT@crapouillou.net/
Suggested-by: Paul Cercueil <paul@crapouillou.net>
Fixes: 171543e752 ("MIPS: Disallow CPU_SUPPORTS_HUGEPAGES for XPA,EVA")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd4eb90b16 ]
Commit ab7c01fdc3 ("mips: Add MIPS Release 5 support") adds the two
configs CPU_MIPS32_R5 and CPU_MIPS64_R5, which depend on the corresponding
SYS_HAS_CPU_MIPS32_R5 and SYS_HAS_CPU_MIPS64_R5, respectively.
The config SYS_HAS_CPU_MIPS32_R5 was already introduced with commit
c5b367835c ("MIPS: Add support for XPA."); the config
SYS_HAS_CPU_MIPS64_R5, however, was never introduced.
Hence, ./scripts/checkkconfigsymbols.py warns:
SYS_HAS_CPU_MIPS64_R5
Referencing files: arch/mips/Kconfig, arch/mips/include/asm/cpu-type.h
Add the definition for config SYS_HAS_CPU_MIPS64_R5 under the assumption
that SYS_HAS_CPU_MIPS64_R5 follows the same pattern as the existing
SYS_HAS_CPU_MIPS32_R5 and SYS_HAS_CPU_MIPS64_R6.
Fixes: ab7c01fdc3 ("mips: Add MIPS Release 5 support")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8d61a9112 ]
The struct device variable "dev_bogus" was triggering this warning
on a PowerPC build:
drivers/of/unittest.c: In function 'of_unittest_dma_ranges_one.constprop':
[...] >> The frame size of 1424 bytes is larger than 1024 bytes
[-Wframe-larger-than=]
This variable is now dynamically allocated.
Fixes: e0d072782c ("dma-mapping: introduce DMA range map, supplanting dma_pfn_offset")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Frank Rowand <frank.rowand@sony.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211210184636.7273-2-jim2101024@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20679094a0 ]
Currently, when cma_resolve_ib_dev() searches for a matching GID it will
stop searching after encountering the first empty GID table entry. This
behavior is wrong since neither IB nor RoCE spec enforce tightly packed
GID tables.
For example, when the matching valid GID entry exists at index N, and if a
GID entry is empty at index N-1, cma_resolve_ib_dev() will fail to find
the matching valid entry.
Fix it by making cma_resolve_ib_dev() continue searching even after
encountering missing entries.
Fixes: f17df3b0de ("RDMA/cma: Add support for AF_IB to rdma_resolve_addr()")
Link: https://lore.kernel.org/r/b7346307e3bb396c43d67d924348c6c496493991.1639055490.git.leonro@nvidia.com
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 483d805191 ]
Currently, ib_find_gid() will stop searching after encountering the first
empty GID table entry. This behavior is wrong since neither IB nor RoCE
spec enforce tightly packed GID tables.
For example, when a valid GID entry exists at index N, and if a GID entry
is empty at index N-1, ib_find_gid() will fail to find the valid entry.
Fix it by making ib_find_gid() continue searching even after encountering
missing entries.
Fixes: 5eb620c81c ("IB/core: Add helpers for uncached GID and P_Key searches")
Link: https://lore.kernel.org/r/e55d331b96cecfc2cf19803d16e7109ea966882d.1639055490.git.leonro@nvidia.com
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 29bbc35e29 ]
pci_irq_vector() and pci_irq_get_affinity() use the list position to find the
MSI-X descriptor at a given index. That's correct for the normal case where
the entry number is the same as the list position.
But it's wrong for cases where MSI-X was allocated with an entries array
describing sparse entry numbers into the hardware message descriptor
table. That's inconsistent at best.
Make it always check the entry number because that's what the zero base
index really means. This change won't break existing users which use a
sparse entries array for allocation because these users retrieve the Linux
interrupt number from the entries array after allocation and none of them
uses pci_irq_vector() or pci_irq_get_affinity().
Fixes: aff171641d ("PCI: Provide sensible IRQ vector alloc/free routines")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20211206210223.929792157@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9abe2ac834 ]
Table descriptors were being installed without properly formatting the
address using paddr_to_iopte, which does not match up with the
iopte_deref in __arm_lpae_map. This is incorrect for the LPAE pte
format, as it does not handle the high bits properly.
This was found on Apple T6000 DARTs, which require a new pte format
(different shift); adding support for that to
paddr_to_iopte/iopte_to_paddr caused it to break badly, as even <48-bit
addresses would end up incorrect in that case.
Fixes: 6c89928ff7 ("iommu/io-pgtable-arm: Support 52-bit physical address")
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Hector Martin <marcan@marcan.st>
Link: https://lore.kernel.org/r/20211120031343.88034-1-marcan@marcan.st
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe6b186924 ]
If a memory copy function fails to copy the whole buffer,
a positive integar with the remaining bytes is returned.
In binder_translate_fd_array() this can result in an fd being
skipped due to the failed copy, but the loop continues
processing fds since the early return condition expects a
negative integer on error.
Fix by returning "ret > 0 ? -EINVAL : ret" to handle this case.
Fixes: bb4a2e48d5 ("binder: return errors from buffer copy functions")
Suggested-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Todd Kjos <tkjos@google.com>
Link: https://lore.kernel.org/r/20211130185152.437403-2-tkjos@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5912cc19a ]
Using MKWORD() on a byte-sized variable results in OOB read. Expand the
size of the reserved area so both MKWORD and MKBYTE continue to work
without overflow. Silences this warning on a -Warray-bounds build:
drivers/char/mwave/3780i.h:346:22: error: array subscript 'short unsigned int[0]' is partly outside array bounds of 'DSP_ISA_SLAVE_CONTROL[1]' [-Werror=array-bounds]
346 | #define MKWORD(var) (*((unsigned short *)(&var)))
| ~^~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/char/mwave/3780i.h:356:40: note: in definition of macro 'OutWordDsp'
356 | #define OutWordDsp(index,value) outw(value,usDspBaseIO+index)
| ^~~~~
drivers/char/mwave/3780i.c:373:41: note: in expansion of macro 'MKWORD'
373 | OutWordDsp(DSP_IsaSlaveControl, MKWORD(rSlaveControl));
| ^~~~~~
drivers/char/mwave/3780i.c:358:31: note: while referencing 'rSlaveControl'
358 | DSP_ISA_SLAVE_CONTROL rSlaveControl;
| ^~~~~~~~~~~~~
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20211203084206.3104326-1-keescook@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c86ff8c55b ]
Since commit db3a34e174 ("clocksource: Retry clock read if long delays
detected") and commit 2e27e793e2 ("clocksource: Reduce clocksource-skew
threshold"), it is found that tsc clocksource fallback to hpet can
sometimes happen on both Intel and AMD systems especially when they are
running stressful benchmarking workloads. Of the 23 systems tested with
a v5.14 kernel, 10 of them have switched to hpet clock source during
the test run.
The result of falling back to hpet is a drastic reduction of performance
when running benchmarks. For example, the fio performance tests can
drop up to 70% whereas the iperf3 performance can drop up to 80%.
4 hpet fallbacks happened during bootup. They were:
[ 8.749399] clocksource: timekeeping watchdog on CPU13: hpet read-back delay of 263750ns, attempt 4, marking unstable
[ 12.044610] clocksource: timekeeping watchdog on CPU19: hpet read-back delay of 186166ns, attempt 4, marking unstable
[ 17.336941] clocksource: timekeeping watchdog on CPU28: hpet read-back delay of 182291ns, attempt 4, marking unstable
[ 17.518565] clocksource: timekeeping watchdog on CPU34: hpet read-back delay of 252196ns, attempt 4, marking unstable
Other fallbacks happen when the systems were running stressful
benchmarks. For example:
[ 2685.867873] clocksource: timekeeping watchdog on CPU117: hpet read-back delay of 57269ns, attempt 4, marking unstable
[46215.471228] clocksource: timekeeping watchdog on CPU8: hpet read-back delay of 61460ns, attempt 4, marking unstable
Commit 2e27e793e2 ("clocksource: Reduce clocksource-skew threshold"),
changed the skew margin from 100us to 50us. I think this is too small
and can easily be exceeded when running some stressful workloads on a
thermally stressed system. So it is switched back to 100us.
Even a maximum skew margin of 100us may be too small in for some systems
when booting up especially if those systems are under thermal stress. To
eliminate the case that the large skew is due to the system being too
busy slowing down the reading of both the watchdog and the clocksource,
an extra consecutive read of watchdog clock is being done to check this.
The consecutive watchdog read delay is compared against
WATCHDOG_MAX_SKEW/2. If the delay exceeds the limit, we assume that
the system is just too busy. A warning will be printed to the console
and the clock skew check is skipped for this round.
Fixes: db3a34e174 ("clocksource: Retry clock read if long delays detected")
Fixes: 2e27e793e2 ("clocksource: Reduce clocksource-skew threshold")
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e27e793e2 ]
Currently, WATCHDOG_THRESHOLD is set to detect a 62.5-millisecond skew in
a 500-millisecond WATCHDOG_INTERVAL. This requires that clocks be skewed
by more than 12.5% in order to be marked unstable. Except that a clock
that is skewed by that much is probably destroying unsuspecting software
right and left. And given that there are now checks for false-positive
skews due to delays between reading the two clocks, it should be possible
to greatly decrease WATCHDOG_THRESHOLD, at least for fine-grained clocks
such as TSC.
Therefore, add a new uncertainty_margin field to the clocksource structure
that contains the maximum uncertainty in nanoseconds for the corresponding
clock. This field may be initialized manually, as it is for
clocksource_tsc_early and clocksource_jiffies, which is copied to
refined_jiffies. If the field is not initialized manually, it will be
computed at clock-registry time as the period of the clock in question
based on the scale and freq parameters to __clocksource_update_freq_scale()
function. If either of those two parameters are zero, the
tens-of-milliseconds WATCHDOG_THRESHOLD is used as a cowardly alternative
to dividing by zero. No matter how the uncertainty_margin field is
calculated, it is bounded below by twice WATCHDOG_MAX_SKEW, that is, by 100
microseconds.
Note that manually initialized uncertainty_margin fields are not adjusted,
but there is a WARN_ON_ONCE() that triggers if any such field is less than
twice WATCHDOG_MAX_SKEW. This WARN_ON_ONCE() is intended to discourage
production use of the one-nanosecond uncertainty_margin values that are
used to test the clock-skew code itself.
The actual clock-skew check uses the sum of the uncertainty_margin fields
of the two clocksource structures being compared. Integer overflow is
avoided because the largest computed value of the uncertainty_margin
fields is one billion (10^9), and double that value fits into an
unsigned int. However, if someone manually specifies (say) UINT_MAX,
they will get what they deserve.
Note that the refined_jiffies uncertainty_margin field is initialized to
TICK_NSEC, which means that skew checks involving this clocksource will
be sufficently forgiving. In a similar vein, the clocksource_tsc_early
uncertainty_margin field is initialized to 32*NSEC_PER_MSEC, which
replicates the current behavior and allows custom setting if needed
in order to address the rare skews detected for this clocksource in
current mainline.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Feng Tang <feng.tang@intel.com>
Link: https://lore.kernel.org/r/20210527190124.440372-4-paulmck@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c9ac51b85 ]
Running perf fuzzer showed below in dmesg logs:
"Can't find PMC that caused IRQ"
This means a PMU exception happened, but none of the PMC's (Performance
Monitor Counter) were found to be overflown. There are some corner cases
that clears the PMCs after PMI gets masked. In such cases, the perf
interrupt handler will not find the active PMC values that had caused
the overflow and thus leads to this message while replaying.
Case 1: PMU Interrupt happens during replay of other interrupts and
counter values gets cleared by PMU callbacks before replay:
During replay of interrupts like timer, __do_irq() and doorbell
exception, we conditionally enable interrupts via may_hard_irq_enable().
This could potentially create a window to generate a PMI. Since irq soft
mask is set to ALL_DISABLED, the PMI will get masked here. We could get
IPIs run before perf interrupt is replayed and the PMU events could
be deleted or stopped. This will change the PMU SPR values and resets
the counters. Snippet of ftrace log showing PMU callbacks invoked in
__do_irq():
<idle>-0 [051] dns. 132025441306354: __do_irq <-call_do_irq
<idle>-0 [051] dns. 132025441306430: irq_enter <-__do_irq
<idle>-0 [051] dns. 132025441306503: irq_enter_rcu <-__do_irq
<idle>-0 [051] dnH. 132025441306599: xive_get_irq <-__do_irq
<<>>
<idle>-0 [051] dnH. 132025441307770: generic_smp_call_function_single_interrupt <-smp_ipi_demux_relaxed
<idle>-0 [051] dnH. 132025441307839: flush_smp_call_function_queue <-smp_ipi_demux_relaxed
<idle>-0 [051] dnH. 132025441308057: _raw_spin_lock <-event_function
<idle>-0 [051] dnH. 132025441308206: power_pmu_disable <-perf_pmu_disable
<idle>-0 [051] dnH. 132025441308337: power_pmu_del <-event_sched_out
<idle>-0 [051] dnH. 132025441308407: power_pmu_read <-power_pmu_del
<idle>-0 [051] dnH. 132025441308477: read_pmc <-power_pmu_read
<idle>-0 [051] dnH. 132025441308590: isa207_disable_pmc <-power_pmu_del
<idle>-0 [051] dnH. 132025441308663: write_pmc <-power_pmu_del
<idle>-0 [051] dnH. 132025441308787: power_pmu_event_idx <-perf_event_update_userpage
<idle>-0 [051] dnH. 132025441308859: rcu_read_unlock_strict <-perf_event_update_userpage
<idle>-0 [051] dnH. 132025441308975: power_pmu_enable <-perf_pmu_enable
<<>>
<idle>-0 [051] dnH. 132025441311108: irq_exit <-__do_irq
<idle>-0 [051] dns. 132025441311319: performance_monitor_exception <-replay_soft_interrupts
Case 2: PMI's masked during local_* operations, example local_add(). If
the local_add() operation happens within a local_irq_save(), replay of
PMI will be during local_irq_restore(). Similar to case 1, this could
also create a window before replay where PMU events gets deleted or
stopped.
Fix it by updating the PMU callback function power_pmu_disable() to
check for pending perf interrupt. If there is an overflown PMC and
pending perf interrupt indicated in paca, clear the PMI bit in paca to
drop that sample. Clearing of PMI bit is done in power_pmu_disable()
since disable is invoked before any event gets deleted/stopped. With
this fix, if there are more than one event running in the PMU, there is
a chance that we clear the PMI bit for the event which is not getting
deleted/stopped. The other events may still remain active. Hence to make
sure we don't drop valid sample in such cases, another check is added in
power_pmu_enable. This checks if there is an overflown PMC found among
the active events and if so enable back the PMI bit. Two new helper
functions are introduced to clear/set the PMI, ie
clear_pmi_irq_pending() and set_pmi_irq_pending(). Helper function
pmi_irq_pending() is introduced to give a warning if there is pending
PMI bit in paca, but no PMC is overflown.
Also there are corner cases which result in performance monitor
interrupts being triggered during power_pmu_disable(). This happens
since PMXE bit is not cleared along with disabling of other MMCR0 bits
in the pmu_disable. Such PMI's could leave the PMU running and could
trigger PMI again which will set MMCR0 PMAO bit. This could lead to
spurious interrupts in some corner cases. Example, a timer after
power_pmu_del() which will re-enable interrupts and triggers a PMI again
since PMAO bit is still set. But fails to find valid overflow since PMC
was cleared in power_pmu_del(). Fix that by disabling PMXE along with
disabling of other MMCR0 bits in power_pmu_disable().
We can't just replay PMI any time. Hence this approach is preferred
rather than replaying PMI before resetting overflown PMC. Patch also
documents core-book3s on a race condition which can trigger these PMC
messages during idle path in PowerNV.
Fixes: f442d00480 ("powerpc/64s: Add support to mask perf interrupts and replay them")
Reported-by: Nageswara R Sastry <nasastry@in.ibm.com>
Suggested-by: Nicholas Piggin <npiggin@gmail.com>
Suggested-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Tested-by: Nageswara R Sastry <rnsastry@linux.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Make pmi_irq_pending() return bool, reflow/reword some comments]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1626846509-1350-2-git-send-email-atrajeev@linux.vnet.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91668ab7db ]
PowerISA v3.1 introduces new control bit (PMCCEXT) for restricting
access to group B PMU registers in problem state when
MMCR0 PMCC=0b00. In problem state and when MMCR0 PMCC=0b00,
setting the Monitor Mode Control Register bit 54 (MMCR0 PMCCEXT),
will restrict read permission on Group B Performance Monitor
Registers (SIER, SIAR, SDAR and MMCR1). When this bit is set to zero,
group B registers will be readable. In other platforms (like power9),
the older behaviour is retained where group B PMU SPRs are readable.
Patch adds support for MMCR0 PMCCEXT bit in power10 by enabling
this bit during boot and during the PMU event enable/disable callback
functions.
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1606409684-1589-8-git-send-email-atrajeev@linux.vnet.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 344fbab991 ]
The only thing keeping the cpu_setup() and cpu_restore() functions
used in the cputable entries for Power7, Power8, Power9 and Power10 in
assembly was cpu_restore() being called before there was a stack in
generic_secondary_smp_init(). Commit ("powerpc/64: Set up a kernel
stack for secondaries before cpu_restore()") means that it is now
possible to use C.
Rewrite the functions in C so they are a little bit easier to read.
This is not changing their functionality.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
[mpe: Tweak copyright and authorship notes]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201014072837.24539-2-jniethe5@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49bcb1506f ]
When converting the thermal-zones bindings to yaml the definition of the
contribution property changed. The intention is the same, an integer
value expressing a ratio of a sum on how much cooling is provided by the
device to the zone. But after the conversion the integer value is
limited to the range 0 to 100 and expressed as a percentage.
This is problematic for two reasons.
- This do not match how the binding is used. Out of the 18 files that
make use of the property only two (ste-dbx5x0.dtsi and
ste-hrefv60plus.dtsi) sets it at a value that satisfy the binding,
100. The remaining 16 files set the value higher and fail to validate.
- Expressing the value as a percentage instead of a ratio of the sum is
confusing as there is nothing to enforce the sum in the zone is not
greater then 100.
This patch restore the pre yaml conversion description and removes the
value limitation allowing the usage of the bindings to validate.
Fixes: 1202a442a3 ("dt-bindings: thermal: Add yaml bindings for thermal zones")
Reported-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20211109103045.1403686-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49f893253a ]
Commit f37fe2f998 ("ASoC: uniphier: add support for UniPhier AIO common
driver") adds configs SND_SOC_UNIPHIER_{LD11,PXS2}, which select the
non-existing config SND_SOC_UNIPHIER_AIO_DMA.
Hence, ./scripts/checkkconfigsymbols.py warns:
SND_SOC_UNIPHIER_AIO_DMA
Referencing files: sound/soc/uniphier/Kconfig
Probably, there is actually no further config intended to be selected
here. So, just drop selecting the non-existing config.
Fixes: f37fe2f998 ("ASoC: uniphier: add support for UniPhier AIO common driver")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20211125095158.8394-2-lukas.bulwahn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 570727e9ac ]
When attempting to use sys_pll1_80m as the parent for clko1, the
system hangs. This is due to the fact that the source select
for sys_pll1_80m was incorrectly pointing to m7_alt_pll_clk, which
doesn't yet exist.
According to Rev 3 of the TRM, The imx8mn_clko1_sels also incorrectly
references an osc_27m which does not exist, nor does an entry for
source select bits 010b. Fix both by inserting a dummy clock into
the missing space in the table and renaming the incorrectly name clock
with dummy.
Fixes: 96d6392b54 ("clk: imx: Add support for i.MX8MN clock driver")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20211117133202.775633-1-aford173@gmail.com
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 173b6e383d ]
A user reported FITRIM ioctl failing for him on ext4 on some devices
without apparent reason. After some debugging we've found out that
these devices (being LVM volumes) report rather large discard
granularity of 42MB and the filesystem had 1k blocksize and thus group
size of 8MB. Because ext4 FITRIM implementation puts discard
granularity into minlen, ext4_trim_fs() declared the trim request as
invalid. However just silently doing nothing seems to be a more
appropriate reaction to such combination of parameters since user did
not specify anything wrong.
CC: Lukas Czerner <lczerner@redhat.com>
Fixes: 5c2ed62fd4 ("ext4: Adjust minlen with discard_granularity in the FITRIM ioctl")
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20211112152202.26614-1-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d668769eb9 ]
Syzbot reported uninit value in mcs7830_bind(). The problem was in
missing validation check for bytes read via usbnet_read_cmd().
usbnet_read_cmd() internally calls usb_control_msg(), that returns
number of bytes read. Code should validate that requested number of bytes
was actually read.
So, this patch adds missing size validation check inside
mcs7830_get_reg() to prevent uninit value bugs
Reported-and-tested-by: syzbot+003c0a286b9af5412510@syzkaller.appspotmail.com
Fixes: 2a36d70834 ("USB: driver for mcs7830 (aka DeLOCK) USB ethernet adapter")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20220106225716.7425-1-paskripkin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ccdcc8ffd ]
When building ARCH=arm allmodconfig:
drivers/net/wireless/intel/iwlwifi/mvm/ftm-initiator.c: In function ‘iwl_mvm_ftm_rtt_smoothing’:
./include/asm-generic/div64.h:222:35: error: comparison of distinct pointer types lacks a cast [-Werror]
222 | (void)(((typeof((n)) *)0) == ((uint64_t *)0)); \
| ^~
drivers/net/wireless/intel/iwlwifi/mvm/ftm-initiator.c:1070:9: note: in expansion of macro ‘do_div’
1070 | do_div(rtt_avg, 100);
| ^~~~~~
do_div() has to be used with an unsigned 64-bit integer dividend but
rtt_avg is a signed 64-bit integer.
div_s64() expects a signed 64-bit integer dividend and signed 32-bit
divisor, which fits this scenario, so use that function here to fix the
warning.
Fixes: 8b0f92549f ("iwlwifi: mvm: fix 32-bit build in FTM")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20211227191757.2354329-1-nathan@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fbb3485f1f ]
We need to set TASK_INTERRUPTIBLE before calling kthread_should_stop().
Otherwise, kthread_stop() might see that the pccardd thread is still
in TASK_RUNNING state and fail to wake it up.
Additionally, we only need to set the state back to TASK_RUNNING if
kthread_should_stop() breaks the loop.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Fixes: d3046ba809 ("pcmcia: fix a boot time warning in pcmcia cs code")
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c6564c13da ]
For the possible failure of the platform_get_irq(), the returned irq
could be error number and will finally cause the failure of the
request_irq().
Consider that platform_get_irq() can now in certain cases return
-EPROBE_DEFER, and the consequences of letting request_irq()
effectively convert that into -EINVAL, even at probe time rather than
later on. So it might be better to check just now.
Fixes: b1201e44f5 ("can: xilinx CAN controller support")
Link: https://lore.kernel.org/all/20211224021324.1447494-1-jiasheng@iscas.ac.cn
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 370d988cc5 ]
In the function softing_startstop() the variable error_reporting is
assigned but not used. The code that uses this variable is commented
out. Its stated that the functionality is not finally verified.
To fix the warning:
| drivers/net/can/softing/softing_fw.c:424:9: error: variable 'error_reporting' set but not used [-Werror,-Wunused-but-set-variable]
remove the comment, activate the code, but add a "0 &&" to the if
expression and rely on the optimizer rather than the preprocessor to
remove the code.
Link: https://lore.kernel.org/all/20220109103126.1872833-1-mkl@pengutronix.de
Fixes: 03fd3cf5a1 ("can: add driver for Softing card")
Cc: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e96d52822f ]
Commit 79ca6f74da ("tpm: fix Atmel TPM crash caused by too frequent
queries") has moved some code around without updating the error handling
path.
This is now pointless to 'goto out_err' when neither 'clk_enable()' nor
'ioremap()' have been called yet.
Make a direct return instead to avoid undoing things that have not been
done.
Fixes: 79ca6f74da ("tpm: fix Atmel TPM crash caused by too frequent queries")
Signed-off-by: Christophe Jaillet <christophe.jaillet@wanadoo.fr>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ef333f5ba ]
Locality is not appropriately requested before writing the int mask.
Add the missing boilerplate.
Fixes: e6aef069b6 ("tpm_tis: convert to using locality callbacks")
Signed-off-by: Chen Jun <chenjun102@huawei.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 530792efa6 ]
Since commit cffa4b2122 ("regmap: debugfs: Fix a memory leak when
calling regmap_attach_dev"), the following debugfs error is seen
on i.MX boards:
debugfs: Directory 'dummy-iomuxc-gpr@20e0000' with parent 'regmap' already present!
In the attempt to fix the memory leak, the above commit added a NULL check
for map->debugfs_name. For the first debufs entry, map->debugfs_name is NULL
and then the new name is allocated via kasprintf().
For the second debugfs entry, map->debugfs_name() is no longer NULL, so
it will keep using the old entry name and the duplicate name error is seen.
Quoting Mark Brown:
"That means that if the device gets freed we'll end up with the old debugfs
file hanging around pointing at nothing.
...
To be more explicit this means we need a call to regmap_debugfs_exit()
which will clean up all the existing debugfs stuff before we loose
references to it."
Call regmap_debugfs_exit() prior to regmap_debugfs_init() to fix
the problem.
Tested on i.MX6Q and i.MX6SX boards.
Fixes: cffa4b2122 ("regmap: debugfs: Fix a memory leak when calling regmap_attach_dev")
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Link: https://lore.kernel.org/r/20220107163307.335404-1-festevam@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc35616e6c ]
This needs to copy an unsigned int from user space instead of a long to
avoid breaking user space with an API change.
I have updated all the integer overflow checks from ULONG to UINT as
well. This is a slight API change but I do not expect it to affect
anything in real life.
Fixes: 3087a6f36e ("netrom: fix copying in user data in nr_setsockopt")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9371937092 ]
The "opt" variable is unsigned long but we only copy 4 bytes from
the user so the lower 4 bytes are uninitialized.
I have changed the integer overflow checks from ULONG to UINT as well.
This is a slight API change but I don't expect it to break anything.
Fixes: a7b75c5a8c ("net: pass a sockptr_t into ->setsockopt")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b70d4f9b2 ]
The "opt" variable is a u32, but on some paths only the top bytes
were initialized and the others contained random stack data.
Fixes: a7b75c5a8c ("net: pass a sockptr_t into ->setsockopt")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e715cd613 ]
Avoid a race where command work handler may fail to allocate command
entry index, by holding the command semaphore down till command entry
index is being freed.
Fixes: 410bd754cd ("net/mlx5: Add retry mechanism to the command entry index allocation")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64050cdad0 ]
This reverts commit 6d6727dddc.
Although the NIC doesn't support offload of outer header CSUM, using
gso_partial_features allows offloading the tunnel's segmentation. The
driver relies on the stack CSUM calculation of the outer header. For
this, NETIF_F_GSO_UDP_TUNNEL_CSUM must be a member of the device's
features.
Fixes: 6d6727dddc ("net/mlx5e: Block offload of outer header csum for UDP tunnels")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e72a55a3c ]
Routes with nexthop objects is currently not supported by multipath offload
and any attempts to use it is blocked, however this also block adding SW
routes with nexthop.
Resolve this by returning NOTIFY_DONE instead of an error which will allow such
a route to be created in SW but not offloaded.
This fix also solve an issue which block adding such routes on different devices
due to missing check if the route FIB device is one of multipath devices.
Fixes: 6a87afc072 ("mlx5: Fail attempts to use routes with nexthop objects")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b7cfa4082 ]
Driver initiates DMA sync, hence it may skip CPU sync. Add
DMA_ATTR_SKIP_CPU_SYNC as input attribute both to dma_map_page and
dma_unmap_page to avoid redundant sync with the CPU.
When forcing the device to work with SWIOTLB, the extra sync might cause
data corruption. The driver unmaps the whole page while the hardware
used just a part of the bounce buffer. So syncing overrides the entire
page with bounce buffer that only partially contains real data.
Fixes: bc77b240b3 ("net/mlx5e: Add fragmented memory support for RX multi packet WQE")
Fixes: db05815b36 ("net/mlx5e: Add XSK zero-copy support")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa320fdbbb ]
The function performs a check on the hdev input parameters, however, it
is used before the check.
Initialize the udev variable after the sanity check to avoid a
possible NULL pointer dereference.
Fixes: 9614219e93 ("HID: uclogic: Extract tablet parameter discovery into a module")
Addresses-Coverity-ID: 1443763 ("Null pointer dereference")
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff6b548afe ]
The function performs a check on its input parameters, however, the
hdev parameter is used before the check.
Initialize the stack variables after checking the input parameters to
avoid a possible NULL pointer dereference.
Fixes: 9614219e93 ("HID: uclogic: Extract tablet parameter discovery into a module")
Addresses-Coverity-ID: 1443804 ("Null pointer dereference")
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a94131d69 ]
The function performs a check on the hdev input parameters, however, it
is used before the check.
Initialize the udev variable after the sanity check to avoid a
possible NULL pointer dereference.
Fixes: 9614219e93 ("HID: uclogic: Extract tablet parameter discovery into a module")
Addresses-Coverity-ID: 1443827 ("Null pointer dereference")
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f364c571a5 ]
The function performs a check on its input parameters, however, the
hdev parameter is used before the check.
Initialize the stack variables after checking the input parameters to
avoid a possible NULL pointer dereference.
Fixes: 9614219e93 ("HID: uclogic: Extract tablet parameter discovery into a module")
Addresses-Coverity-ID: 1443831 ("Null pointer dereference")
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6845667146 ]
The function devm_gpiod_get_index() return error pointers on error.
Thus devm_gpiod_get_index_optional() could return NULL and error pointers.
The same as devm_gpiod_get_optional() function. Using IS_ERR_OR_NULL()
check to catch error pointers.
Fixes: 77131dfe ("Bluetooth: hci_qca: Replace devm_gpiod_get() with devm_gpiod_get_optional()")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b38cd3b42f ]
For the possible failure of the platform_get_irq(), the returned irq
could be error number and will finally cause the failure of the
request_irq().
Consider that platform_get_irq() can now in certain cases return
-EPROBE_DEFER, and the consequences of letting request_irq() effectively
convert that into -EINVAL, even at probe time rather than later on.
So it might be better to check just now.
Fixes: 0395ffc1ee ("Bluetooth: hci_bcm: Add PM for BCM devices")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5a73ec96c ]
As the possible failure of the allocation, the devm_ioremap() may return
NULL pointer.
Take tgec_initialization() as an example.
If allocation fails, the params->base_addr will be NULL pointer and will
be assigned to tgec->regs in tgec_config().
Then it will cause the dereference of NULL pointer in set_mac_address(),
which is called by tgec_init().
Therefore, it should be better to add the sanity check after the calling
of the devm_ioremap().
Fixes: 3933961682 ("fsl/fman: Add FMan MAC driver")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e81948177 ]
As the possible alloc failure of devm_kcalloc(), it could return null
pointer.
Therefore, 'strings' should be checked and return NULL if alloc fails to
prevent the dereference of the NULL pointer.
Also, the caller should also deal with the return value of the
gb_generate_enum_strings() and return -ENOMEM if returns NULL.
Moreover, because the memory allocated with devm_kzalloc() will be
freed automatically when the last reference to the device is dropped,
the 'gbe' in gbaudio_tplg_create_enum_kctl() and
gbaudio_tplg_create_enum_ctl() do not need to free manually.
But the 'control' in gbaudio_tplg_create_widget() and
gbaudio_tplg_process_kcontrols() has a specially error handle to
cleanup.
So it should be better to cleanup 'control' when fails.
Fixes: e65579e335 ("greybus: audio: topology: Enable enumerated control support")
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20220104150628.1987906-1-jiasheng@iscas.ac.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43d0121231 ]
This code is holding the &ofdpa->flow_tbl_lock spinlock so it is not
allowed to sleep. That means we have to pass the OFDPA_OP_FLAG_NOWAIT
flag to ofdpa_flow_tbl_del().
Fixes: 936bd48656 ("rocker: use FIB notifications instead of switchdev calls")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4407318799 ]
It seems pretty clear ppp layer assumed user space
would always be kind to provide enough data
in their write() to a ppp device.
This patch makes sure user provides at least
2 bytes.
It adds PPP_PROTO_LEN macro that could replace
in net-next many occurrences of hard-coded 2 value.
I replaced only one occurrence to ease backports
to stable kernels.
The bug manifests in the following report:
BUG: KMSAN: uninit-value in ppp_send_frame+0x28d/0x27c0 drivers/net/ppp/ppp_generic.c:1740
ppp_send_frame+0x28d/0x27c0 drivers/net/ppp/ppp_generic.c:1740
__ppp_xmit_process+0x23e/0x4b0 drivers/net/ppp/ppp_generic.c:1640
ppp_xmit_process+0x1fe/0x480 drivers/net/ppp/ppp_generic.c:1661
ppp_write+0x5cb/0x5e0 drivers/net/ppp/ppp_generic.c:513
do_iter_write+0xb0c/0x1500 fs/read_write.c:853
vfs_writev fs/read_write.c:924 [inline]
do_writev+0x645/0xe00 fs/read_write.c:967
__do_sys_writev fs/read_write.c:1040 [inline]
__se_sys_writev fs/read_write.c:1037 [inline]
__x64_sys_writev+0xe5/0x120 fs/read_write.c:1037
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x54/0xd0 arch/x86/entry/common.c:82
entry_SYSCALL_64_after_hwframe+0x44/0xae
Uninit was created at:
slab_post_alloc_hook mm/slab.h:524 [inline]
slab_alloc_node mm/slub.c:3251 [inline]
__kmalloc_node_track_caller+0xe0c/0x1510 mm/slub.c:4974
kmalloc_reserve net/core/skbuff.c:354 [inline]
__alloc_skb+0x545/0xf90 net/core/skbuff.c:426
alloc_skb include/linux/skbuff.h:1126 [inline]
ppp_write+0x11d/0x5e0 drivers/net/ppp/ppp_generic.c:501
do_iter_write+0xb0c/0x1500 fs/read_write.c:853
vfs_writev fs/read_write.c:924 [inline]
do_writev+0x645/0xe00 fs/read_write.c:967
__do_sys_writev fs/read_write.c:1040 [inline]
__se_sys_writev fs/read_write.c:1037 [inline]
__x64_sys_writev+0xe5/0x120 fs/read_write.c:1037
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x54/0xd0 arch/x86/entry/common.c:82
entry_SYSCALL_64_after_hwframe+0x44/0xae
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linux-ppp@vger.kernel.org
Reported-by: syzbot <syzkaller@googlegroups.com>
Acked-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23c54263ef ]
This is needed in case a new transaction is made that doesn't insert any
new elements into an already existing set.
Else, after second 'nft -f ruleset.txt', lookups in such a set will fail
because ->lookup() encounters raw_cpu_ptr(m->scratch) == NULL.
For the initial rule load, insertion of elements takes care of the
allocation, but for rule reloads this isn't guaranteed: we might not
have additions to the set.
Fixes: 3c4287f620 ("nf_tables: Add set type for arbitrary concatenation of ranges")
Reported-by: etkaar <lists.netfilter.org@prvy.eu>
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e60b0d12a9 ]
If we ever get to a point again where we convert a bogus looking <ptr>_or_null
typed register containing a non-zero fixed or variable offset, then lets not
reset these bounds to zero since they are not and also don't promote the register
to a <ptr> type, but instead leave it as <ptr>_or_null. Converting to a unknown
register could be an avenue as well, but then if we run into this case it would
allow to leak a kernel pointer this way.
Fixes: f1174f77b5 ("bpf/verifier: rework value tracking")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d94a69cb2c ]
The issue takes place in one error path of clusterip_tg_check(). When
memcmp() returns nonzero, the function simply returns the error code,
forgetting to decrease the reference count of a clusterip_config
object, which is bumped earlier by clusterip_config_find_get(). This
may incur reference count leak.
Fix this issue by decrementing the refcount of the object in specific
error path.
Fixes: 06aa151ad1 ("netfilter: ipt_CLUSTERIP: check MAC address when duplicate config is set")
Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn>
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c1348bf05 ]
The return value of platform_get_resource() needs to be checked.
To avoid use of error pointer in case that there is no suitable
resource.
Fixes: d28c74c107 ("power: reset: add driver for mt6323 poweroff")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 977d2e7c63 ]
In nonstatic_find_mem_region(), pcmcia_make_resource() is assigned to
res and used in pci_bus_alloc_resource(). There a dereference of res
in pci_bus_alloc_resource(), which could lead to a NULL pointer
dereference on failure of pcmcia_make_resource().
Fix this bug by adding a check of res.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_PCCARD_NONSTATIC=y show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: 49b1153adf ("pcmcia: move all pcmcia_resource_ops providers into one module")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca0fe0d7c3 ]
In __nonstatic_find_io_region(), pcmcia_make_resource() is assigned to
res and used in pci_bus_alloc_resource(). There is a dereference of res
in pci_bus_alloc_resource(), which could lead to a NULL pointer
dereference on failure of pcmcia_make_resource().
Fix this bug by adding a check of res.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_PCCARD_NONSTATIC=y show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: 49b1153adf ("pcmcia: move all pcmcia_resource_ops providers into one module")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
[linux@dominikbrodowski.net: Fix typo in commit message]
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f85196bdd5 ]
BCM4752 and LNV4752 ACPI nodes describe a Broadcom 4752 GPS module
attached to an UART of the system.
The GPS modules talk a custom protocol which only works with a closed-
source Android gpsd daemon which knows this protocol.
The ACPI nodes also describe GPIOs to turn the GPS on/off these are
handled by the net/rfkill/rfkill-gpio.c code. This handling predates the
addition of enumeration of ACPI instantiated serdevs to the kernel and
was broken by that addition, because the ACPI scan code now no longer
instantiates platform_device-s for these nodes.
Rename the i2c_multi_instantiate_ids HID list to ignore_serial_bus_ids
and add the BCM4752 and LNV4752 HIDs, so that rfkill-gpio gets
a platform_device to bind to again; and so that a tty cdev for gpsd
gets created for these.
Fixes: e361d1f858 ("ACPI / scan: Fix enumeration for special UART devices")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de768416b2 ]
A contrived zero-length write, for example, by using write(2):
...
ret = write(fd, str, 0);
...
to the "flags" file causes:
BUG: KASAN: stack-out-of-bounds in flags_write
Write of size 1 at addr ffff888019be7ddf by task writefile/3787
CPU: 4 PID: 3787 Comm: writefile Not tainted 5.16.0-rc7+ #12
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-2 04/01/2014
due to accessing buf one char before its start.
Prevent such out-of-bounds access.
[ bp: Productize into a proper patch. Link below is the next best
thing because the original mail didn't get archived on lore. ]
Fixes: 0451d14d05 ("EDAC, mce_amd_inj: Modify flags attribute to use string arguments")
Signed-off-by: Zhang Zixun <zhang133010@icloud.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/linux-edac/YcnePfF1OOqoQwrX@zn.tnic/
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8d6d4992a ]
In the file mr75203.c we have a macro named POWER_DELAY_CYCLE_256,
the correct value should be 0x100. The register ip_tmr is expressed
in units of IP clk cycles, in accordance with the datasheet.
Typical power-up delays for Temperature Sensor are 256 cycles i.e. 0x100.
Fixes: 9d823351a3 ("hwmon: Add hardware monitoring driver for Moortec MR75203 PVT controller")
Signed-off-by: Arseny Demidov <a.demidov@yadro.com>
Link: https://lore.kernel.org/r/20211219102239.1112-1-a.demidov@yadro.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5fe392ff9d ]
When cross compiling i386_defconfig on an arm64 host with clang, there
are a few instances of '-Waddress-of-packed-member' and
'-Wgnu-variable-sized-type-not-at-end' in arch/x86/boot/compressed/,
which should both be disabled with the cc-disable-warning calls in that
directory's Makefile, which indicates that cc-disable-warning is failing
at the point of testing these flags.
The cc-disable-warning calls fail because at the point that the flags
are tested, KBUILD_CFLAGS has '-march=i386' without $(CLANG_FLAGS),
which has the '--target=' flag to tell clang what architecture it is
targeting. Without the '--target=' flag, the host architecture (arm64)
is used and i386 is not a valid value for '-march=' in that case. This
error can be seen by adding some logging to try-run:
clang-14: error: the clang compiler does not support '-march=i386'
Invoking the compiler has to succeed prior to calling cc-option or
cc-disable-warning in order to accurately test whether or not the flag
is supported; if it doesn't, the requested flag can never be added to
the compiler flags. Move $(CLANG_FLAGS) to the beginning of KBUILD_FLAGS
so that any new flags that might be added in the future can be
accurately tested.
Fixes: d5cbd80e30 ("x86/boot: Add $(CLANG_FLAGS) to compressed KBUILD_CFLAGS")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20211222163040.1961481-1-nathan@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df1e5c5149 ]
The IBS timers are not stopped properly once BT OFF is triggered.
we could see IBS commands being sent along with version command,
so stopped IBS timers while Bluetooth is off.
Fixes: 3e4be65eb8 ("Bluetooth: hci_qca: Add poweroff support during hci down for wcn3990")
Signed-off-by: Panicker Harish <quic_pharish@quicinc.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec961cf324 ]
The hardware is capable of controlling any non-contiguous sequence of
LEDs specified in the DT using qcom,enabled-strings as u32
array, and this also follows from the DT-bindings documentation. The
numbers specified in this array represent indices of the LED strings
that are to be enabled and disabled.
Its value is appropriately used to setup and enable string modules, but
completely disregarded in the set_brightness paths which only iterate
over the number of strings linearly.
Take an example where only string 2 is enabled with
qcom,enabled_strings=<2>: this string is appropriately enabled but
subsequent brightness changes would have only touched the zero'th
brightness register because num_strings is 1 here. This is simply
addressed by looking up the string for this index in the enabled_strings
array just like the other codepaths that iterate over num_strings.
Likewise enabled_strings is now also used in the autodetection path for
consistent behaviour: when a list of strings is specified in DT only
those strings will be probed for autodetection, analogous to how the
number of strings that need to be probed is already bound by
qcom,num-strings. After all autodetection uses the set_brightness
helpers to set an initial value, which could otherwise end up changing
brightness on a different set of strings.
Fixes: 775d2ffb4a ("backlight: qcom-wled: Restructure the driver for WLED3")
Fixes: 03b2b5e869 ("backlight: qcom-wled: Add support for WLED4 peripheral")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211115203459.1634079-10-marijn.suijten@somainline.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b4b49602f ]
The length of qcom,enabled-strings as property array is enough to
determine the number of strings to be enabled, without needing to set
qcom,num-strings to override the default number of strings when less
than the default (which is also the maximum) is provided in DT.
This also introduces an extra warning when qcom,num-strings is set,
denoting that it is not necessary to set both anymore. It is usually
more concise to set just qcom,num-length when a zero-based, contiguous
range of strings is needed (the majority of the cases), or to only set
qcom,enabled-strings when a specific set of indices is desired.
Fixes: 775d2ffb4a ("backlight: qcom-wled: Restructure the driver for WLED3")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211115203459.1634079-6-marijn.suijten@somainline.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ada78b26f ]
When not specifying num-strings in the DT the default is used, but +1 is
added to it which turns WLED3 into 4 and WLED4/5 into 5 strings instead
of 3 and 4 respectively, causing out-of-bounds reads and register
read/writes. This +1 exists for a deficiency in the DT parsing code,
and is simply omitted entirely - solving this oob issue - by parsing the
property separately much like qcom,enabled-strings.
This also enables more stringent checks on the maximum value when
qcom,enabled-strings is provided in the DT, by parsing num-strings after
enabled-strings to allow it to check against (and in a subsequent patch
override) the length of enabled-strings: it is invalid to set
num-strings higher than that.
The DT currently utilizes it to get around an incorrect fixed read of
four elements from that array (has been addressed in a prior patch) by
setting a lower num-strings where desired.
Fixes: 93c64f1ea1 ("leds: add Qualcomm PM8941 WLED driver")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-By: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211115203459.1634079-5-marijn.suijten@somainline.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e29e24bdab ]
of_property_read_u32_array takes the number of elements to read as last
argument. This does not always need to be 4 (sizeof(u32)) but should
instead be the size of the array in DT as read just above with
of_property_count_elems_of_size.
To not make such an error go unnoticed again the driver now bails
accordingly when of_property_read_u32_array returns an error.
Surprisingly the indentation of newlined arguments is lining up again
after prepending `rc = `.
Fixes: 775d2ffb4a ("backlight: qcom-wled: Restructure the driver for WLED3")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211115203459.1634079-3-marijn.suijten@somainline.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a1a0b0364 ]
The output of bpftool prog tracelog is currently buffered, which is
inconvenient when piping the output into other commands. A simple
tracelog | grep will typically not display anything. This patch fixes it
by enabling line buffering on stdout for the whole bpftool binary.
Fixes: 30da46b5dc ("tools: bpftool: add a command to dump the trace pipe")
Signed-off-by: Quentin Monnet <quentin@isovalent.com>
Signed-off-by: Paul Chaignon <paul@isovalent.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20211220214528.GA11706@Mem
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30d5772273 ]
If user has a set to use SOCK_STREAM the socket would default to
L2CAP_MODE_ERTM which later needs to be adjusted if the destination
address is LE which doesn't support such mode.
Fixes: 15f02b9105 ("Bluetooth: L2CAP: Add initial code for Enhanced Credit Based Mode")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 85e73968a0 ]
When creating an external event, the current time needs to
be propagated to other participants of a simulation. This
is done in the places here where we kick a virtq etc.
However, it must be done for _all_ external events, and
that includes making the initial socket connection and
later closing it. Call time_travel_propagate_time() to do
this before making or closing the socket connection.
Apparently, at least for the initial connection creation,
due to the remote side in my use cases using microseconds
(rather than nanoseconds), this wasn't a problem yet; only
started failing between 5.14-rc1 and 5.15-rc1 (didn't test
others much), or possibly depending on the configuration,
where more delays happen before the virtio devices are
initialized.
Fixes: 88ce642492 ("um: Implement time-travel=ext")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f8539e2ff ]
Many places in the kernel use 'udelay' as an identifier, and
are broken with the current "#define udelay um_udelay". Fix
this by adding an argument to the macro, and do the same to
'ndelay' as well, just in case.
Fixes: 0bc8fb4dda ("um: Implement ndelay/udelay in time-travel mode")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8fc9a77bc6 ]
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_threaded_irq()
(which takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_threaded_irq() with the
invalid IRQ #s.
Fixes: ed80a13bb4 ("mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b SoC")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20211217202717.10041-3-s.shtylyov@omp.ru
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77bed755e0 ]
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_threaded_irq()
(which takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_threaded_irq() with the
invalid IRQ #s.
Fixes: e4bf1b0970 ("mmc: host: meson-mx-sdhc: new driver for the Amlogic Meson SDHC host")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20211217202717.10041-2-s.shtylyov@omp.ru
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6248077226 ]
Add generic compatible string "ns16550a" to serial port nodes of Armada
38x.
This makes it possible to use earlycon.
Fixes: 0d3d96ab00 ("ARM: mvebu: add Device Tree description of the Armada 380/385 SoCs")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0734f8311c ]
CN9130 has a built-in CP115 which has 2 GPIO controllers, but unlike in
Armada 7k and 8k both are left disabled by the SoC DTSI.
This first of all makes no sense as they are always present due to being
SoC built-in and its an issue as boards like CN9130-CRB use the CPO GPIO2
pins for regulators and SD card support without enabling them first.
So, enable both of them like Armada 7k and 8k do.
Fixes: 6b8970bd8d ("arm64: dts: marvell: Add support for Marvell CN9130 SoC support")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit effd42600b ]
CN9130 has one CP115 built in, which like the CP110 has 2 GPIO and 2 SPI
controllers built-in.
However, unlike the Armada 7k and 8k the SoC DTSI doesn't add the required
aliases as both the Orion SPI driver and MVEBU GPIO drivers require the
aliases to be present.
So add the required aliases for GPIO and SPI controllers.
Fixes: 6b8970bd8d ("arm64: dts: marvell: Add support for Marvell CN9130 SoC support")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a92882a4d2 ]
In the decompressor's head.S we need to start with an instruction that
is some kind of NOP, but also mimics as the PE/COFF header, when the
kernel is linked as an UEFI application. The clever solution here is
"tstne r0, #0x4d000", which in the worst case just clobbers the
condition flags, and bears the magic "MZ" signature in the lowest 16 bits.
However the encoding used (0x13105a4d) is actually not valid, since bits
[15:12] are supposed to be 0 (written as "(0)" in the ARM ARM).
Violating this is UNPREDICTABLE, and *can* trigger an UNDEFINED
exception. Common Cortex cores seem to ignore those bits, but QEMU
chooses to trap, so the code goes fishing because of a missing exception
handler at this point. We are just saved by the fact that commonly (with
-kernel or when running from U-Boot) the "Z" bit is set, so the
instruction is never executed. See [0] for more details.
To make things more robust and avoid UNPREDICTABLE behaviour in the
kernel code, lets replace this with a "two-instruction NOP":
The first instruction is an exclusive OR, the effect of which the second
instruction reverts. This does not leave any trace, neither in a
register nor in the condition flags. Also it's a perfectly valid
encoding. Kudos to Peter Maydell for coming up with this gem.
[0] https://lore.kernel.org/qemu-devel/YTPIdbUCmwagL5%2FD@os.inf.tu-dresden.de/T/
Link: https://lore.kernel.org/linux-arm-kernel/20210908162617.104962-1-andre.przywara@arm.com/T/
Fixes: 81a0bc39ea ("ARM: add UEFI stub support")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reported-by: Adam Lackorzynski <adam@l4re.org>
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8dce439195 ]
xfrm interface if_id = 0 would cause xfrm policy lookup errors since
Commit 9f8550e4bd.
Now explicitly fail to create an xfrm interface when if_id = 0
With this commit:
ip link add ipsec0 type xfrm dev lo if_id 0
Error: if_id must be non zero.
v1->v2 change:
- add Fixes: tag
Fixes: 9f8550e4bd ("xfrm: fix disable_xfrm sysctl when used on xfrm interfaces")
Signed-off-by: Antony Antony <antony.antony@secunet.com>
Reviewed-by: Eyal Birger <eyal.birger@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5566174cb1 ]
Upon failure, dma_alloc_coherent() returns NULL. If that does happen,
passing some uninitialised stack contents to dma_mapping_error() - which
belongs to a different API in the first place - has precious little
chance of detecting it.
Also include the correct header, because the fragile transitive
inclusion currently providing it is going to break soon.
Fixes: 20e7dce255 ("drm/tegra: Remove memory allocation from Falcon library")
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Mikko Perttunen <mperttunen@nvidia.com>
CC: dri-devel@lists.freedesktop.org
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c02b360ca6 ]
Currently Soundcard has 1 rx device for headset and SoundWire Speaker Playback.
This setup has issues, ex if we try to play on headset the audio stream is
also sent to SoundWire Speakers and we will hear sound in both headsets and speakers.
Make a separate device for Speakers and Headset so that the streams are
different and handled properly.
Fixes: 45021d35fc ("arm64: dts: qcom: c630: Enable audio support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211209175342.20386-2-srinivas.kandagatla@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eccd251363 ]
In ath11k_mac_op_hw_scan(), the return value of kzalloc() is directly
used in memcpy(), which may lead to a NULL pointer dereference on
failure of kzalloc().
Fix this bug by adding a check of arg.extraie.ptr.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_ATH11K=m show no new warnings, and our static
analyzer no longer warns about this code.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211202155348.71315-1-zhou1615@umn.edu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d5831a40d ]
I got a null-ptr-deref report:
BUG: kernel NULL pointer dereference, address: 0000000000000060
...
RIP: 0010:v4l2_ctrl_auto_cluster+0x57/0x270
...
Call Trace:
msi001_probe+0x13b/0x24b [msi001]
spi_probe+0xeb/0x130
...
do_syscall_64+0x35/0xb0
In msi001_probe(), if the creation of control for bandwidth_auto
fails, there will be a null-ptr-deref issue when it is used in
v4l2_ctrl_auto_cluster().
Check dev->hdl.error before v4l2_ctrl_auto_cluster() to fix this bug.
Link: https://lore.kernel.org/linux-media/20211026112348.2878040-1-wanghai38@huawei.com
Fixes: 93203dd6c7 ("[media] msi001: Mirics MSi001 silicon tuner driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 589a9f0eb7 ]
dvb_usb_device_init stores parts of properties at d->props
and d->desc and uses it on dvb_usb_device_exit.
Free of properties on module probe leads to use after free.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=204597
The patch makes properties static instead of allocated on heap to prevent
memleak and use after free.
Also fixes s421_properties.devices initialization to have 2 element
instead of 6 copied from p7500_properties.
[mchehab: fix function call alignments]
Link: https://lore.kernel.org/linux-media/20190822104147.4420-1-vasilyev@ispras.ru
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Fixes: 299c7007e9 ("media: dw2102: Fix memleak on sequence of probes")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4754eab7e5 ]
Steven Maddox reported in the OpenWrt bugzilla, that his
RaidSonic IB-NAS4220-B was no longer booting with the new
OpenWrt 21.02 (uses linux 5.10's device-tree). However, it was
working with the previous OpenWrt 19.07 series (uses 4.14).
|[ 5.548038] No RedBoot partition table detected in 30000000.flash
|[ 5.618553] Searching for RedBoot partition table in 30000000.flash at offset 0x0
|[ 5.739093] No RedBoot partition table detected in 30000000.flash
|...
|[ 7.039504] Waiting for root device /dev/mtdblock3...
The provided bootlog shows that the RedBoot partition parser was
looking for the partition table "at offset 0x0". Which is strange
since the comment in the device-tree says it should be at 0xfe0000.
Further digging on the internet led to a review site that took
some useful PCB pictures of their review unit back in February 2009.
Their picture shows a Spansion S29GL128N11TFI01 flash chip.
>From Spansion's Datasheet:
"S29GL128N: One hundred twenty-eight 64 Kword (128 Kbyte) sectors"
Steven also provided a "cat /sys/class/mtd/mtd0/erasesize" from his
unit: "131072".
With the 128 KiB Sector/Erasesize in mind. This patch changes the
fis-index-block property to (0xfe0000 / 0x20000) = 0x7f.
Fixes: b5a923f8c7 ("ARM: dts: gemini: Switch to redboot partition parsing")
Reported-by: Steven Maddox <s.maddox@lantizia.me.uk>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Steven Maddox <s.maddox@lantizia.me.uk>
Link: https://lore.kernel.org/r/20211206004334.4169408-1-linus.walleij@linaro.org'
Bugzilla: https://bugs.openwrt.org/index.php?do=details&task_id=4137
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d6b661330 ]
We should not call pm_runtime_resume_and_get where the reference
count is expected to be incremented unconditionally. This patch
reverts these calls to the original unconditional get_sync call.
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: 747bf30fd9 ("crypto: stm32/cryp - Fix PM reference leak...")
Fixes: 1cb3ad7019 ("crypto: stm32/hash - Fix PM reference leak...")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b898d5cfa ]
Extra crypto manager auto test were crashing or failling due
to 2 reasons:
- block in a dead loop (dues to issues in cipher end process management)
- crash due to read/write unmapped memory (this crash was also reported
when using openssl afalg engine)
Rework interrupt management, interrupts are masked as soon as they are
no more used: if input buffer is fully consumed, "Input FIFO not full"
interrupt is masked and if output buffer is full, "Output FIFO not
empty" interrupt is masked.
And crypto request finish when input *and* outpout buffer are fully
read/write.
About the crash due to unmapped memory, using scatterwalk_copychunks()
that will map and copy each block fix the issue.
Using this api and copying full block will also fix unaligned data
access, avoid early copy of in/out buffer, and make useless the extra
alignment constraint.
Fixes: 9e054ec21e ("crypto: stm32 - Support for STM32 CRYP crypto module")
Reported-by: Marek Vasut <marex@denx.de>
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa97dc2d48 ]
This fixes the lrw autotest if lrw uses the CRYP as the AES block cipher
provider (as ecb(aes)). At end of request, CRYP should not update the IV
in case of ECB chaining mode. Indeed the ECB chaining mode never uses
the IV, but the software LRW chaining mode uses the IV field as
a counter and due to the (unexpected) update done by CRYP while the AES
block process, the counter get a wrong value when the IV overflow.
Fixes: 5f49f18d27 ("crypto: stm32/cryp - update to return iv_out")
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39e6e699c7 ]
Some auto tests failed because driver wasn't returning the expected
error with some input size/iv value/tag size.
Now:
Return 0 early for empty buffer. (We don't need to start the engine for
an empty input buffer).
Accept any valid authsize for gcm(aes).
Return -EINVAL if iv for ccm(aes) is invalid.
Return -EINVAL if buffer size is a not a multiple of algorithm block size.
Fixes: 9e054ec21e ("crypto: stm32 - Support for STM32 CRYP crypto module")
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d703c7a994 ]
Don't erase key:
If key is erased before the crypto_finalize_.*_request() call, some
pending process will run with a key={ 0 }.
Moreover if the key is reset at end of request, it breaks xts chaining
mode, as for last xts block (in case input len is not a multiple of
block) a new AES request is started without calling again set_key().
Fixes: 9e054ec21e ("crypto: stm32 - Support for STM32 CRYP crypto module")
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41c76690b0 ]
STM32 CRYP hardware doesn't manage CTR counter bigger than max U32, as
a workaround, at each block the current IV is saved, if the saved IV
lower u32 is 0xFFFFFFFF, the full IV is manually incremented, and set
in hardware.
Fixes: bbb2832620 ("crypto: stm32 - Fix sparse warnings")
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 81064c96d8 ]
This patch changes the cast in stm32_cryp_check_ctr_counter from
u32 to __be32 to match the prototype of stm32_cryp_hw_write_iv
correctly.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3abedf4646 ]
Test can fail either immediately when ASSERT() failed or at the
end if one or more EXPECT() was not met. The exact return code
is decided based on the number of successful ASSERT()s.
If test has no ASSERT()s, however, the return code will be 0,
as if the test did not fail. Start counting ASSERT()s from 1.
Fixes: 369130b631 ("selftests: Enhance kselftest_harness.h to print which assert failed")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a531b0c23c ]
Building selftests/clone3 with clang warns about enumeration not handled
in switch case:
clone3.c:54:10: warning: enumeration value 'CLONE3_ARGS_NO_TEST' not handled in switch [-Wswitch]
switch (test_mode) {
^
Add the missing switch case with a comment.
Fixes: 17a810699c ("selftests: add tests for clone3()")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61646ca83d ]
When building with automatic stack variable initialization, GCC 12
complains about variables defined outside of switch case statements.
Move the variable into the case that uses it, which silences the warning:
./arch/x86/include/asm/uaccess.h:317:23: warning: statement will never be executed [-Wswitch-unreachable]
317 | unsigned char x_u8__; \
| ^~~~~~
Fixes: 865c50e1d2 ("x86/uaccess: utilize CONFIG_CC_HAS_ASM_GOTO_OUTPUT")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20211209043456.1377875-1-keescook@chromium.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b8bb8919e ]
Quoting Jia-Ju Bai <baijiaju1990@gmail.com>:
mwifiex_dequeue_tx_packet()
spin_lock_bh(&priv->wmm.ra_list_spinlock); --> Line 1432 (Lock A)
mwifiex_send_addba()
spin_lock_bh(&priv->sta_list_spinlock); --> Line 608 (Lock B)
mwifiex_process_sta_tx_pause()
spin_lock_bh(&priv->sta_list_spinlock); --> Line 398 (Lock B)
mwifiex_update_ralist_tx_pause()
spin_lock_bh(&priv->wmm.ra_list_spinlock); --> Line 941 (Lock A)
Similar report for mwifiex_process_uap_tx_pause().
While the locking expectations in this driver are a bit unclear, the
Fixed commit only intended to protect the sta_ptr, so we can drop the
lock as soon as we're done with it.
IIUC, this deadlock cannot actually happen, because command event
processing (which calls mwifiex_process_sta_tx_pause()) is
sequentialized with TX packet processing (e.g.,
mwifiex_dequeue_tx_packet()) via the main loop (mwifiex_main_process()).
But it's good not to leave this potential issue lurking.
Fixes: f0f7c2275f ("mwifiex: minor cleanups w/ sta_list_spinlock in cfg80211.c")
Cc: Douglas Anderson <dianders@chromium.org>
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Link: https://lore.kernel.org/linux-wireless/0e495b14-efbb-e0da-37bd-af6bd677ee2c@gmail.com/
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/YaV0pllJ5p/EuUat@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 81f6d49cce ]
Expedited RCU grace periods invoke sync_rcu_exp_select_node_cpus(), which
takes two passes over the leaf rcu_node structure's CPUs. The first
pass gathers up the current CPU and CPUs that are in dynticks idle mode.
The workqueue will report a quiescent state on their behalf later.
The second pass sends IPIs to the rest of the CPUs, but excludes the
current CPU, incorrectly assuming it has been included in the first
pass's list of CPUs.
Unfortunately the current CPU may have changed between the first and
second pass, due to the fact that the various rcu_node structures'
->lock fields have been dropped, thus momentarily enabling preemption.
This means that if the second pass's CPU was not on the first pass's
list, it will be ignored completely. There will be no IPI sent to
it, and there will be no reporting of quiescent states on its behalf.
Unfortunately, the expedited grace period will nevertheless be waiting
for that CPU to report a quiescent state, but with that CPU having no
reason to believe that such a report is needed.
The result will be an expedited grace period stall.
Fix this by no longer excluding the current CPU from consideration during
the second pass.
Fixes: b9ad4d6ed1 ("rcu: Avoid self-IPI in sync_rcu_exp_select_node_cpus()")
Reviewed-by: Neeraj Upadhyay <quic_neeraju@quicinc.com>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Cc: Uladzislau Rezki <urezki@gmail.com>
Cc: Neeraj Upadhyay <quic_neeraju@quicinc.com>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Joel Fernandes <joel@joelfernandes.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b58e976b3 ]
When rt_runtime is modified from -1 to a valid control value, it may
cause the task to be throttled all the time. Operations like the following
will trigger the bug. E.g:
1. echo -1 > /proc/sys/kernel/sched_rt_runtime_us
2. Run a FIFO task named A that executes while(1)
3. echo 950000 > /proc/sys/kernel/sched_rt_runtime_us
When rt_runtime is -1, The rt period timer will not be activated when task
A enqueued. And then the task will be throttled after setting rt_runtime to
950,000. The task will always be throttled because the rt period timer is
not activated.
Fixes: d0b27fa778 ("sched: rt-group: synchonised bandwidth period")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Li Hua <hucool.lihua@huawei.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20211203033618.11895-1-hucool.lihua@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f973795a8d ]
In iwl_txq_dyn_alloc_dma, txq->tfds is freed at first time by:
iwl_txq_alloc()->goto err_free_tfds->dma_free_coherent(). But
it forgot to set txq->tfds to NULL.
Then the txq->tfds is freed again in iwl_txq_dyn_alloc_dma by:
goto error->iwl_txq_gen2_free_memory()->dma_free_coherent().
My patch sets txq->tfds to NULL after the first free to avoid the
double free.
Fixes: 0cd1ad2d7f ("iwlwifi: move all bus-independent TX functions to common code")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Link: https://lore.kernel.org/r/20210403054755.4781-1-lyl2019@mail.ustc.edu.cn
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6441ea29c ]
Commit e955f959ac ("media: si2157: Better check for running tuner in
init") completely broke the "warm" tuner detection of the si2157 driver
due to a simple endian error: The Si2157 CRYSTAL_TRIM property code is
0x0402 and needs to be transmitted LSB first. However, it was inserted
MSB first, causing the warm detection to always fail and spam the kernel
log with tuner initialization messages each time the DVB frontend
device was closed and reopened:
[ 312.215682] si2157 16-0060: found a 'Silicon Labs Si2157-A30'
[ 312.264334] si2157 16-0060: firmware version: 3.0.5
[ 342.248593] si2157 16-0060: found a 'Silicon Labs Si2157-A30'
[ 342.295743] si2157 16-0060: firmware version: 3.0.5
[ 372.328574] si2157 16-0060: found a 'Silicon Labs Si2157-A30'
[ 372.385035] si2157 16-0060: firmware version: 3.0.5
Also, the reinitializations were observed disturb _other_ tuners on
multi-tuner cards such as the Hauppauge WinTV-QuadHD, leading to missed
or errored packets when one of the other DVB frontend devices on that
card was opened.
Fix the order of the property code bytes to make the warm detection work
again, also reducing the tuner initialization message in the kernel log
to once per power-on, as well as fixing the interference with other
tuners.
Link: https://lore.kernel.org/linux-media/trinity-2a86eb9d-6264-4387-95e1-ba7b79a4050f-1638392923493@3c-app-gmx-bap03
Fixes: e955f959ac ("media: si2157: Better check for running tuner in init")
Reported-by: Robert Schlabbach <robert_s@gmx.net>
Signed-off-by: Robert Schlabbach <robert_s@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0407c49ebe ]
In mxb_attach(dev, info), saa7146_vv_init() is called to allocate a
new memory for dev->vv_data. saa7146_vv_release() will be called on
failure of mxb_probe(dev). There is a dereference of dev->vv_data
in saa7146_vv_release(), which could lead to a NULL pointer dereference
on failure of saa7146_vv_init().
Fix this bug by adding a check of saa7146_vv_init().
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_VIDEO_MXB=m show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: 03b1930efd ("V4L/DVB: saa7146: fix regression of the av7110/budget-av driver")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8dbdcc7269 ]
In dib8000_init(), the variable fe is not freed or passed out on the
failure of dib8000_identify(&state->i2c), which could lead to a memleak.
Fix this bug by adding a kfree of fe in the error path.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_DVB_DIB8000=m show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: 77e2c0f5d4 ("V4L/DVB (12900): DiB8000: added support for DiBcom ISDB-T/ISDB-Tsb demodulator DiB8000")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db52f57211 ]
Branch data available to BPF programs can be very useful to get stack traces
out of userspace application.
Commit fff7b64355 ("bpf: Add bpf_read_branch_records() helper") added BPF
support to capture branch records in x86. Enable this feature also for other
architectures as well by removing checks specific to x86.
If an architecture doesn't support branch records, bpf_read_branch_records()
still has appropriate checks and it will return an -EINVAL in that scenario.
Based on UAPI helper doc in include/uapi/linux/bpf.h, unsupported architectures
should return -ENOENT in such case. Hence, update the appropriate check to
return -ENOENT instead.
Selftest 'perf_branches' result on power9 machine which has the branch stacks
support:
- Before this patch:
[command]# ./test_progs -t perf_branches
#88/1 perf_branches/perf_branches_hw:FAIL
#88/2 perf_branches/perf_branches_no_hw:OK
#88 perf_branches:FAIL
Summary: 0/1 PASSED, 0 SKIPPED, 1 FAILED
- After this patch:
[command]# ./test_progs -t perf_branches
#88/1 perf_branches/perf_branches_hw:OK
#88/2 perf_branches/perf_branches_no_hw:OK
#88 perf_branches:OK
Summary: 1/2 PASSED, 0 SKIPPED, 0 FAILED
Selftest 'perf_branches' result on power9 machine which doesn't have branch
stack report:
- After this patch:
[command]# ./test_progs -t perf_branches
#88/1 perf_branches/perf_branches_hw:SKIP
#88/2 perf_branches/perf_branches_no_hw:OK
#88 perf_branches:OK
Summary: 1/1 PASSED, 1 SKIPPED, 0 FAILED
Fixes: fff7b64355 ("bpf: Add bpf_read_branch_records() helper")
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20211206073315.77432-1-kjain@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 014ba44e81 ]
select_idle_sibling() has a special case for tasks woken up by a per-CPU
kthread where the selected CPU is the previous one. For asymmetric CPU
capacity systems, the assumption was that the wakee couldn't have a
bigger utilization during task placement than it used to have during the
last activation. That was not considering uclamp.min which can completely
change between two task activations and as a consequence mandates the
fitness criterion asym_fits_capacity(), even for the exit path described
above.
Fixes: b4c9c9f156 ("sched/fair: Prefer prev cpu in asymmetric wakeup path")
Signed-off-by: Vincent Donnefort <vincent.donnefort@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Link: https://lkml.kernel.org/r/20211129173115.4006346-1-vincent.donnefort@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b4e74ccb5 ]
select_idle_sibling() has a special case for tasks woken up by a per-CPU
kthread, where the selected CPU is the previous one. However, the current
condition for this exit path is incomplete. A task can wake up from an
interrupt context (e.g. hrtimer), while a per-CPU kthread is running. A
such scenario would spuriously trigger the special case described above.
Also, a recent change made the idle task like a regular per-CPU kthread,
hence making that situation more likely to happen
(is_per_cpu_kthread(swapper) being true now).
Checking for task context makes sure select_idle_sibling() will not
interpret a wake up from any other context as a wake up by a per-CPU
kthread.
Fixes: 52262ee567 ("sched/fair: Allow a per-CPU kthread waking a task to stack on the same CPU, to fix XFS performance regression")
Signed-off-by: Vincent Donnefort <vincent.donnefort@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Vincent Guittot <vincent.guittot@linaro.org>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Link: https://lore.kernel.org/r/20211201143450.479472-1-vincent.donnefort@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 561ae1d46a ]
btmtksdio have to rely on MMC_PM_KEEP_POWER in pm_flags to avoid that
SDIO power is being shut off during the device is in suspend. That fixes
the SDIO command fails to access the bus after the device is resumed.
Fixes: 7f3c563c57 ("Bluetooth: btmtksdio: Add runtime PM support to SDIO based Bluetooth")
Co-developed-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb48febce7 ]
When the watchdog detects a disk change, it calls cancel_activity(),
which in turn tries to cancel the fd_timer delayed work.
In the above scenario, fd_timer_fn is set to fd_watchdog(), meaning
it is trying to cancel its own work.
This results in a hang as cancel_delayed_work_sync() is waiting for the
watchdog (itself) to return, which never happens.
This can be reproduced relatively consistently by attempting to read a
broken floppy, and ejecting it while IO is being attempted and retried.
To resolve this, this patch calls cancel_delayed_work() instead, which
cancels the work without waiting for the watchdog to return and finish.
Before this regression was introduced, the code in this section used
del_timer(), and not del_timer_sync() to delete the watchdog timer.
Link: https://lore.kernel.org/r/399e486c-6540-db27-76aa-7a271b061f76@tasossah.com
Fixes: 070ad7e793 ("floppy: convert to delayed work and single-thread wq")
Signed-off-by: Tasos Sahanidis <tasos@tasossah.com>
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1180405c7 ]
With commit 3873e2d7f6 ("drivers: PL011: refactor pl011_probe()") the
function devm_ioremap() called from pl011_setup_port() was replaced with
devm_ioremap_resource(). Since this function not only remaps but also
requests the ports io memory region it now collides with the .config_port()
callback which requests the same region at uart port registration.
Since devm_ioremap_resource() already claims the memory successfully, the
request in .config_port() fails.
Later at uart port deregistration the attempt to release the unclaimed
memory also fails. The failure results in a “Trying to free nonexistent
resource" warning.
Fix these issues by removing the callbacks that implement the redundant
memory allocation/release. Also make sure that changing the drivers io
memory base address via TIOCSSERIAL is not allowed any more.
Fixes: 3873e2d7f6 ("drivers: PL011: refactor pl011_probe()")
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Link: https://lore.kernel.org/r/20211129174238.8333-1-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3672fb6515 ]
The base address of uartlite registers could be 64 bit address which is from
device resource. When ulite_probe() calls ulite_assign(), this 64 bit
address is casted to 32-bit. The fix is to replace "u32" type with
"phys_addr_t" type for the base address in ulite_assign() argument list.
Fixes: 8fa7b61006 ("[POWERPC] Uartlite: Separate the bus binding from the driver proper")
Signed-off-by: Lizhi Hou <lizhi.hou@xilinx.com>
Link: https://lore.kernel.org/r/20211129202302.1319033-1-lizhi.hou@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab50cb9df8 ]
In radeon_driver_open_kms(), radeon_vm_bo_add() is assigned to
vm->ib_bo_va and passes and used in radeon_vm_bo_set_addr(). In
radeon_vm_bo_set_addr(), there is a dereference of vm->ib_bo_va,
which could lead to a NULL pointer dereference on failure of
radeon_vm_bo_add().
Fix this bug by adding a check of vm->ib_bo_va.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_DRM_RADEON=m show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: cc9e67e3d7 ("drm/radeon: fix VM IB handling")
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b220110e4c ]
In amdgpu_connector_lcd_native_mode(), the return value of
drm_mode_duplicate() is assigned to mode, and there is a dereference
of it in amdgpu_connector_lcd_native_mode(), which will lead to a NULL
pointer dereference on failure of drm_mode_duplicate().
Fix this bug add a check of mode.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_DRM_AMDGPU=m show no new warnings, and
our static analyzer no longer warns about this code.
Fixes: d38ceaf99e ("drm/amdgpu: add core driver (v4)")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a9af6cac0 ]
The flushing of pending work in the EC driver uses drain_workqueue()
to flush the event handling work that can requeue itself via
advance_transaction(), but this is problematic, because that
work may also be requeued from the query workqueue.
Namely, if an EC transaction is carried out during the execution of
a query handler, it involves calling advance_transaction() which
may queue up the event handling work again. This causes the kernel
to complain about attempts to add a work item to the EC event
workqueue while it is being drained and worst-case it may cause a
valid event to be skipped.
To avoid this problem, introduce two new counters, events_in_progress
and queries_in_progress, incremented when a work item is queued on
the event workqueue or the query workqueue, respectively, and
decremented at the end of the corresponding work function, and make
acpi_ec_dispatch_gpe() the workqueues in a loop until the both of
these counters are zero (or system wakeup is pending) instead of
calling acpi_ec_flush_work().
At the same time, change __acpi_ec_flush_work() to call
flush_workqueue() instead of drain_workqueue() to flush the event
workqueue.
While at it, use the observation that the work item queued in
acpi_ec_query() cannot be pending at that time, because it is used
only once, to simplify the code in there.
Additionally, clean up a comment in acpi_ec_query() and adjust white
space in acpi_ec_event_processor().
Fixes: f0ac20c3f6 ("ACPI: EC: Fix flushing of pending work")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e14da77113 ]
Various trace event fields that store cgroup IDs were declared as
ints, but cgroup_id(() returns a u64 and the structures and associated
TP_printk() calls were not updated to reflect this.
Fixes: 743210386c ("cgroup: use cgrp->kn->id as the cgroup ID")
Signed-off-by: William Kucharski <william.kucharski@oracle.com>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28b78ecffe ]
This makes 'bridge-nf-filter-pppoe-tagged' sysctl work for
bridged traffic.
Looking at the original commit it doesn't appear this ever worked:
static unsigned int br_nf_post_routing(unsigned int hook, struct sk_buff **pskb,
[..]
if (skb->protocol == htons(ETH_P_8021Q)) {
skb_pull(skb, VLAN_HLEN);
skb->network_header += VLAN_HLEN;
+ } else if (skb->protocol == htons(ETH_P_PPP_SES)) {
+ skb_pull(skb, PPPOE_SES_HLEN);
+ skb->network_header += PPPOE_SES_HLEN;
}
[..]
NF_HOOK(... POST_ROUTING, ...)
... but the adjusted offsets are never restored.
The alternative would be to rip this code out for good,
but otoh we'd have to keep this anyway for the vlan handling
(which works because vlan tag info is in the skb, not the packet
payload).
Reported-and-tested-by: Amish Chana <amish@3g.co.za>
Fixes: 516299d2f5 ("[NETFILTER]: bridge-nf: filter bridged IPv4/IPv6 encapsulated in pppoe traffic")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4cf2ddf16e ]
Starting with commit d92ed2c9d3 ("thermal: imx: Use driver's local
data to decide whether to run a measurement") this driver stared using
irq_enabled flag to make decision to power on/off the thermal
core. This triggered a regression, where after reaching critical
temperature, alarm IRQ handler set irq_enabled to false, disabled
thermal core and was not able read temperature and disable cooling
sequence.
In case the cooling device is "CPU/GPU freq", the system will run with
reduce performance until next reboot.
To solve this issue, we need to move all parts implementing hand made
runtime power management and let it handle actual runtime PM framework.
Fixes: d92ed2c9d3 ("thermal: imx: Use driver's local data to decide whether to run a measurement")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Tested-by: Petr Beneš <petr.benes@ysoft.com>
Link: https://lore.kernel.org/r/20211117103426.81813-1-o.rempel@pengutronix.de
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8cc7a1b2ac ]
A successful 'of_platform_populate()' call should be balanced by a
corresponding 'of_platform_depopulate()' call in the error handling path
of the probe, as already done in the remove function.
A successful 'venus_firmware_init()' call should be balanced by a
corresponding 'venus_firmware_deinit()' call in the error handling path
of the probe, as already done in the remove function.
Update the error handling path accordingly.
Fixes: f9799fcce4 ("media: venus: firmware: register separate platform_device for firmware loader")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4debea9be ]
The normal path of the function makes the assumption that
'pm_ops->core_power' may be NULL.
We should make the same assumption in the error handling path or a NULL
pointer dereference may occur.
Add the missing test before calling 'pm_ops->core_power'
Fixes: 9e8efdb578 ("media: venus: core: vote for video-mem path")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a76f43a490 ]
Presently we use device_link to control core power domain. But this
leads to issues because the genpd doesn't guarantee synchronous on/off
for supplier devices. Switch to manually control by pmruntime calls.
Tested-by: Fritz Koenig <frkoenig@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed2f97ad4b ]
After devm_request_threaded_irq() is called there is a chance that an
interrupt may occur before the spinlock is initialized, which will trigger
a kernel oops.
To prevent that, move the initialization of the spinlock prior to
requesting the interrupts.
Fixes: 51abcf7fdb ("media: imx-pxp: add i.MX Pixel Pipeline driver")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cee44d4fba ]
hsfreqrange should be chosen based on the calculated mbps which
is closer to the default bit rate and within the range as per
table[1]. But current calculation always selects first value which
is greater than or equal to the calculated mbps which may lead
to chosing a wrong range in some cases.
For example for 360 mbps for H3/M3N
Existing logic selects
Calculated value 360Mbps : Default 400Mbps Range [368.125 -433.125 mbps]
This hsfreqrange is out of range.
The logic is changed to get the default value which is closest to the
calculated value [1]
Calculated value 360Mbps : Default 350Mbps Range [320.625 -380.625 mpbs]
[1] specs r19uh0105ej0200-r-car-3rd-generation.pdf [Table 25.9]
Please note that According to Renesas in Table 25.9 the range for
220 default value is corrected as below
|Range (Mbps) | Default Bit rate (Mbps) |
-----------------------------------------------
| 197.125-244.125 | 220 |
-----------------------------------------------
Fixes: 769afd212b ("media: rcar-csi2: add Renesas R-Car MIPI CSI-2 receiver driver")
Signed-off-by: Suresh Udipi <sudipi@jp.adit-jv.com>
Signed-off-by: Kazuyoshi Akiyama <akiyama@nds-osk.co.jp>
Signed-off-by: Michael Rodin <mrodin@de.adit-jv.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d051cf94f ]
Flexcom IP embeds 3 other IPs: usart, i2c, spi and selects the operation
mode (usart, i2c, spi) via mode register (FLEX_MR). On i2c bus there might
be connected critical devices (like PMIC) which on suspend/resume should
be suspended/resumed at the end/beginning. i2c uses
.suspend_noirq/.resume_noirq for this kind of purposes. Align flexcom
to use .resume_noirq as it should be resumed before the embedded IPs.
Otherwise the embedded devices might behave badly.
Fixes: 7fdec11015 ("atmel_flexcom: Support resuming after a chip reset")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Tested-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211028135138.3481166-3-claudiu.beznea@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e67bd2b8c ]
The tx_submit() method of struct dma_async_tx_descriptor is entitled
to do sanity checks and return errors if encountered. It's not the
case for the DMA controller drivers that this client is using
(at_h/xdmac), because they currently don't do sanity checks and always
return a positive cookie at tx_submit() method. In case the controller
drivers will implement sanity checks and return errors, print a message
so that the client will be informed that something went wrong at
tx_submit() level.
Fixes: 08f738be88 ("serial: at91: add tx dma support")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Link: https://lore.kernel.org/r/20211125090028.786832-3-tudor.ambarus@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b689f091aa ]
CE interrupt configuration uses host ce parameters to assign/free
interrupts. Use host ce parameters to enable/disable interrupts.
This patch fixes below BUG,
BUG: KASAN: global-out-of-bounds in 0xffffffbffdfb035c at addr
ffffffbffde6eeac
Read of size 4 by task kworker/u8:2/132
Address belongs to variable ath11k_core_qmi_firmware_ready+0x1b0/0x5bc [ath11k]
OOB is due to ath11k_ahb_ce_irqs_enable() iterates ce_count(which is 12)
times and accessing 12th element in target_ce_config
(which has only 11 elements) from ath11k_ahb_ce_irq_enable().
With this change host ce configs are used to enable/disable interrupts.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00471-QCAHKSWPL_SILICONZ-1
Fixes: 967c1d1131 ("ath11k: move target ce configs to hw_params")
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1637249558-12793-1-git-send-email-akolli@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5002200b4f ]
If the remote function did not ACK the reception of a message, the
function __adf_iov_putmsg() could detect it as a collision.
This was due to the fact that the collision and the timeout checks after
the ACK loop were in the wrong order. The timeout must be checked at the
end of the loop, so fix by swapping the order of the two checks.
Fixes: 9b768e8a39 ("crypto: qat - detect PFVF collision after ACK")
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Co-developed-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e680f94bc ]
The functions adf_iov_putmsg() and __adf_iov_putmsg() are shared by both
PF and VF. Any logging or documentation should not refer to any specific
direction.
Make comments and log messages direction agnostic by replacing PF2VF
with PFVF. Also fix the wording for some related comments.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e17f49bb24 ]
The initial version of the PFVF protocol included an initial "carrier
sensing" to get ownership of the channel.
Collisions can happen anyway, the extra wait and test does not prevent
collisions, it instead slows the communication down, so remove it.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b046049e59 ]
Since the compatible string defined from ilitek,ili9341.yaml is
"st,sf-tc240t-9370-t", "ilitek,ili9341"
so, append "ilitek,ili9341" to avoid the below dtbs_check warning.
arch/arm/boot/dts/stm32f429-disco.dt.yaml: display@1: compatible:
['st,sf-tc240t-9370-t'] is too short
Fixes: a726e2f000 ("ARM: dts: stm32: enable ltdc binding with ili9341, gyro l3gd20 on stm32429-disco board")
Signed-off-by: Dillon Min <dillon.minfei@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit baaf965f94 ]
The following KASAN BUG is observed when testing the rpc-if driver on
rcar-gen3:
root@rcar-gen3:~# modprobe -r rpc-if
[ 101.930146] ==================================================================
[ 101.937408] BUG: KASAN: slab-out-of-bounds in __lock_acquire+0x518/0x25d0
[ 101.944240] Read of size 8 at addr ffff0004c5be2750 by task modprobe/664
[ 101.950959]
[ 101.952466] CPU: 2 PID: 664 Comm: modprobe Not tainted 5.14.0-rc1-00342-g1a1464d7aa31 #1
[ 101.960578] Hardware name: Renesas H3ULCB board based on r8a77951 (DT)
[ 101.967120] Call trace:
[ 101.969580] dump_backtrace+0x0/0x2c0
[ 101.973275] show_stack+0x1c/0x30
[ 101.976616] dump_stack_lvl+0x9c/0xd8
[ 101.980301] print_address_description.constprop.0+0x74/0x2b8
[ 101.986071] kasan_report+0x1f4/0x26c
[ 101.989757] __asan_load8+0x98/0xd4
[ 101.993266] __lock_acquire+0x518/0x25d0
[ 101.997215] lock_acquire.part.0+0x18c/0x360
[ 102.001506] lock_acquire+0x74/0x90
[ 102.005013] _raw_spin_lock_irq+0x98/0x130
[ 102.009131] __pm_runtime_disable+0x30/0x210
[ 102.013427] rpcif_hb_remove+0x5c/0x70 [rpc_if]
[ 102.018001] platform_remove+0x40/0x80
[ 102.021771] __device_release_driver+0x234/0x350
[ 102.026412] driver_detach+0x158/0x20c
[ 102.030179] bus_remove_driver+0xa0/0x140
[ 102.034212] driver_unregister+0x48/0x80
[ 102.038153] platform_driver_unregister+0x18/0x24
[ 102.042879] rpcif_platform_driver_exit+0x1c/0x34 [rpc_if]
[ 102.048400] __arm64_sys_delete_module+0x210/0x310
[ 102.053212] invoke_syscall+0x60/0x190
[ 102.056986] el0_svc_common+0x12c/0x144
[ 102.060844] do_el0_svc+0x88/0xac
[ 102.064181] el0_svc+0x24/0x3c
[ 102.067257] el0t_64_sync_handler+0x1a8/0x1b0
[ 102.071634] el0t_64_sync+0x198/0x19c
[ 102.075315]
[ 102.076815] Allocated by task 628:
[ 102.080781]
[ 102.082280] Last potentially related work creation:
[ 102.087524]
[ 102.089022] The buggy address belongs to the object at ffff0004c5be2000
[ 102.089022] which belongs to the cache kmalloc-2k of size 2048
[ 102.101555] The buggy address is located 1872 bytes inside of
[ 102.101555] 2048-byte region [ffff0004c5be2000, ffff0004c5be2800)
[ 102.113486] The buggy address belongs to the page:
[ 102.118409]
[ 102.119908] Memory state around the buggy address:
[ 102.124711] ffff0004c5be2600: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 102.131947] ffff0004c5be2680: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 102.139181] >ffff0004c5be2700: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 102.146412] ^
[ 102.152257] ffff0004c5be2780: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 102.159491] ffff0004c5be2800: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 102.166723] ==================================================================
The above bug is caused by use of the wrong pointer in the
rpcif_disable_rpm() call. Fix the bug by using the correct pointer.
Fixes: 5de15b610f ("mtd: hyperbus: add Renesas RPC-IF driver")
Signed-off-by: George G. Davis <davis.george@siemens.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20210716204935.25859-1-george_davis@mentor.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4cb4d3163 ]
Pointer base points to sub field of tmpl, it
is dereferenced after tmpl is freed. Fix
this by accessing base before free tmpl.
Fixes: ec8f5d8f ("crypto: qce - Qualcomm crypto engine driver")
Signed-off-by: Chengfeng Ye <cyeaa@connect.ust.hk>
Acked-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab599eb118 ]
I got a use-after-free report:
dvbdev: dvb_register_device: failed to create device dvb1.dvr0 (-12)
...
==================================================================
BUG: KASAN: use-after-free in dvb_dmxdev_release+0xce/0x2f0
...
Call Trace:
dump_stack_lvl+0x6c/0x8b
print_address_description.constprop.0+0x48/0x70
kasan_report.cold+0x82/0xdb
__asan_load4+0x6b/0x90
dvb_dmxdev_release+0xce/0x2f0
...
Allocated by task 7666:
kasan_save_stack+0x23/0x50
__kasan_kmalloc+0x83/0xa0
kmem_cache_alloc_trace+0x22e/0x470
dvb_register_device+0x12f/0x980
dvb_dmxdev_init+0x1f3/0x230
...
Freed by task 7666:
kasan_save_stack+0x23/0x50
kasan_set_track+0x20/0x30
kasan_set_free_info+0x24/0x40
__kasan_slab_free+0xf2/0x130
kfree+0xd1/0x5c0
dvb_register_device.cold+0x1ac/0x1fa
dvb_dmxdev_init+0x1f3/0x230
...
When dvb_register_device() in dvb_dmxdev_init() fails, dvb_dmxdev_init()
does not return a failure, and the memory pointed to by dvbdev or
dvr_dvbdev is invalid at this point. If they are used subsequently, it
will result in UFA or null-ptr-deref.
If dvb_register_device() in dvb_dmxdev_init() fails, fix the bug by making
dvb_dmxdev_init() return an error as well.
Link: https://lore.kernel.org/linux-media/20211015085741.1203283-1-wanghai38@huawei.com
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b9beda83e ]
This patch will surround the AF_INET6 case in sk_error_report() of dlm
with a #if IS_ENABLED(CONFIG_IPV6). The field sk->sk_v6_daddr is not
defined when CONFIG_IPV6 is disabled. If CONFIG_IPV6 is disabled, the
socket creation with AF_INET6 should already fail because a runtime
check if AF_INET6 is registered. However if there is the possibility
that AF_INET6 is set as sk_family the sk_error_report() callback will
print then an invalid family type error.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 4c3d90570b ("fs: dlm: don't call kernel_getpeername() in error_report()")
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f18397ab3a ]
Prior to this patch was teedev_close_context() calling tee_device_put()
before teedev_ctx_put() leading to teedev_ctx_release() accessing
ctx->teedev just after the reference counter was decreased on the
teedev. Fix this by calling teedev_ctx_put() before tee_device_put().
Fixes: 217e0250cc ("tee: use reference counting for tee_context")
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64bc3aa02a ]
The ath11k driver is caching the information about RSN/WPA IE in the
configured beacon template. The cached information is used during
associations to figure out whether 4-way PKT/2-way GTK peer flags need to
be set or not.
But the code never cleared the state when no such IE was found. This can
for example happen when moving from an WPA/RSN to an open setup. The
(seemingly connected) peer was then not able to communicate over the
link because the firmware assumed a different (encryption enabled) state
for the peer.
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Fixes: 01e34233c6 ("ath11k: fix wmi peer flags in peer assoc command")
Cc: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Karthikeyan Kathirvel <kathirve@codeaurora.org>
[sven@narfation.org: split into separate patches, clean up commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211115100441.33771-2-sven@narfation.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 436a4e8865 ]
DISABLE_KEY sets the key_len to 0, firmware will not delete the keys if
key_len is 0. Changing from security mode to open mode will cause mcast
to be still encrypted without vdev restart.
Set the proper key_len for DISABLE_KEY cmd to clear the keys in
firmware.
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Karthikeyan Kathirvel <kathirve@codeaurora.org>
[sven@narfation.org: split into separate patches, clean up commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211115100441.33771-1-sven@narfation.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 086c921a35 ]
Some ETSI countries have a small overlap in the wireless-regdb with an ETSI
channel (5590-5650). A good example is Australia:
country AU: DFS-ETSI
(2400 - 2483.5 @ 40), (36)
(5150 - 5250 @ 80), (23), NO-OUTDOOR, AUTO-BW
(5250 - 5350 @ 80), (20), NO-OUTDOOR, AUTO-BW, DFS
(5470 - 5600 @ 80), (27), DFS
(5650 - 5730 @ 80), (27), DFS
(5730 - 5850 @ 80), (36)
(57000 - 66000 @ 2160), (43), NO-OUTDOOR
If the firmware (or the BDF) is shipped with these rules then there is only
a 10 MHz overlap with the weather radar:
* below: 5470 - 5590
* weather radar: 5590 - 5600
* above: (none for the rule "5470 - 5600 @ 80")
There are several wrong assumption in the ath11k code:
* there is always a valid range below the weather radar
(actually: there could be no range below the weather radar range OR range
could be smaller than 20 MHz)
* intersected range in the weather radar range is valid
(actually: the range could be smaller than 20 MHz)
* range above weather radar is either empty or valid
(actually: the range could be smaller than 20 MHz)
These wrong assumption will lead in this example to a rule
(5590 - 5600 @ 20), (N/A, 27), (600000 ms), DFS, AUTO-BW
which is invalid according to is_valid_reg_rule() because the freq_diff is
only 10 MHz but the max_bandwidth is set to 20 MHz. Which results in a
rejection like:
WARNING: at backports-20210222_001-4.4.60-b157d2276/net/wireless/reg.c:3984
[...]
Call trace:
[<ffffffbffc3d2e50>] reg_get_max_bandwidth+0x300/0x3a8 [cfg80211]
[<ffffffbffc3d3d0c>] regulatory_set_wiphy_regd_sync+0x3c/0x98 [cfg80211]
[<ffffffbffc651598>] ath11k_regd_update+0x1a8/0x210 [ath11k]
[<ffffffbffc652108>] ath11k_regd_update_work+0x18/0x20 [ath11k]
[<ffffffc0000a93e0>] process_one_work+0x1f8/0x340
[<ffffffc0000a9784>] worker_thread+0x25c/0x448
[<ffffffc0000aedc8>] kthread+0xd0/0xd8
[<ffffffc000085550>] ret_from_fork+0x10/0x40
ath11k c000000.wifi: failed to perform regd update : -22
Invalid regulatory domain detected
To avoid this, the algorithm has to be changed slightly. Instead of
splitting a rule which overlaps with the weather radar range into 3 pieces
and accepting the first two parts blindly, it must actually be checked for
each piece whether it is a valid range. And only if it is valid, add it to
the output array.
When these checks are in place, the processed rules for AU would end up as
country AU: DFS-ETSI
(2400 - 2483 @ 40), (N/A, 36), (N/A)
(5150 - 5250 @ 80), (6, 23), (N/A), NO-OUTDOOR, AUTO-BW
(5250 - 5350 @ 80), (6, 20), (0 ms), NO-OUTDOOR, DFS, AUTO-BW
(5470 - 5590 @ 80), (6, 27), (0 ms), DFS, AUTO-BW
(5650 - 5730 @ 80), (6, 27), (0 ms), DFS, AUTO-BW
(5730 - 5850 @ 80), (6, 36), (N/A), AUTO-BW
and will be accepted by the wireless regulatory code.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211112153116.1214421-1-sven@narfation.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a56ef719f ]
Syzbot reported slab-out-of-bounds read in hci_le_adv_report_evt(). The
problem was in missing validaion check.
We should check if data is not malicious and we can read next data block.
If we won't check ptr validness, code can read a way beyond skb->end and
it can cause problems, of course.
Fixes: e95beb4141 ("Bluetooth: hci_le_adv_report_evt code refactoring")
Reported-and-tested-by: syzbot+e3fcb9c4f3c2a931dc40@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit feb704bd17 ]
Instead of dereference "con->sock" we can get the socket structure over
"sk->sk_socket" as well. This patch will switch to this behaviour.
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af6d1bde39 ]
If res-chg, VE_INTERRUPT_MODE_DETECT_WD irq will be raised. But
v4l2_input_status won't be updated to no-signal immediately until
aspeed_video_get_resolution() in aspeed_video_resolution_work().
During the period of time, aspeed_video_start_frame() could be called
because it doesn't know signal becomes unstable now. If it goes with
aspeed_video_init_regs() of aspeed_video_irq_res_change()
simultaneously, it will mess up hw state.
To fix this problem, v4l2_input_status is updated to no-signal
immediately for VE_INTERRUPT_MODE_DETECT_WD irq.
Fixes: d2b4387f3b ("media: platform: Add Aspeed Video Engine driver")
Signed-off-by: Jammy Huang <jammy_huang@aspeedtech.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 22be5a10d0 ]
In the em28xx_init_rev, if em28xx_audio_setup fails, this function fails
to deallocate the media_dev allocated in the em28xx_media_device_init.
Fix this by adding em28xx_unregister_media_device to free media_dev.
BTW, this patch is tested in my local syzkaller instance, and it can
prevent the memory leak from occurring again.
CC: Pavel Skripkin <paskripkin@gmail.com>
Fixes: 37ecc7b127 ("[media] em28xx: add media controller support")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Reported-by: syzkaller <syzkaller@googlegroups.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62cea52ad4 ]
aspeed_video_get_resolution() will try to do res-detect again if the
timing got in last try is invalid. But it will always time out because
VE_SEQ_CTRL_TRIG_MODE_DET is only cleared after 1st mode-detect.
To fix the problem, just clear VE_SEQ_CTRL_TRIG_MODE_DET before setting
it in aspeed_video_enable_mode_detect().
Fixes: d2b4387f3b ("media: platform: Add Aspeed Video Engine driver")
Signed-off-by: Jammy Huang <jammy_huang@aspeedtech.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fae46cb053 ]
Changeset 374d62e7aa ("media: v4l2-subdev: Verify v4l2_subdev_call() pad config argument")
added an extra verification for a pads parameter for enum mbus
format code.
Such change broke atomisp, because now the V4L2 core
refuses to enum MBUS formats if the state is empty.
So, add .which field in order to select the active formats,
in order to make it work again.
While here, improve error messages.
Fixes: 374d62e7aa ("media: v4l2-subdev: Verify v4l2_subdev_call() pad config argument")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a016c35a3 ]
Balance braces around conditional statements.
Issue detected by checkpatch.pl.
It happens in if-else statements where one of the commands
uses braces around a block of code and the other command
does not since it has just a single line of code.
Signed-off-by: Aline Santana Cordeiro <alinesantanacordeiro@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a1b272555 ]
## `if (pipe->stream->config.mode == IA_CSS_INPUT_MODE_TPG) {` case
The intel-aero atomisp has `#if defined(IS_ISP_2400_SYSTEM)` [1]. It is
to be defined in the following two places [2]:
- css/hive_isp_css_common/system_global.h
- css/css_2401_csi2p_system/system_global.h
and the former file is to be included on ISP2400 devices, too. So, it
is to be defined for both ISP2400 and ISP2401 devices.
Because the upstreamed atomisp driver now supports only ISP2400 and
ISP2401, just remove the ISP version test again. This matches the other
upstream commits like 3c0538fbad ("media: atomisp: get rid of most
checks for ISP2401 version").
While here, moved the comment for define GP_ISEL_TPG_MODE to the
appropriate place.
[1] a1b673258f/drivers/media/pci/atomisp/css/sh_css.c (L552-L558)
[2] https://github.com/intel-aero/linux-kernel/search?q=IS_ISP_2400_SYSTEM
## `isys_stream_descr->polling_mode` case
This does not exist on the intel-aero atomisp. This is because it is
based on css version irci_stable_candrpv_0415_20150521_0458.
On the other hand, the upstreamed atomisp is based on the following css
version depending on the ISP version using ifdefs:
- ISP2400: irci_stable_candrpv_0415_20150521_0458
- ISP2401: irci_master_20150911_0724
The `isys_stream_descr->polling_mode` usage was added on updating css
version to irci_master_20150701_0213 [3].
So, it is not a ISP version specific thing, but css version specific
thing. Because the upstreamed atomisp driver uses irci_master_20150911_0724
for ISP2401, re-add the ISP version check for now.
I say "for now" because ISP2401 should eventually use the same css
version with ISP2400 (i.e., irci_stable_candrpv_0415_20150521_0458)
[3] https://raw.githubusercontent.com/intel/ProductionKernelQuilts/cht-m1stable-2016_ww31/uefi/cht-m1stable/patches/cam-0439-atomisp2-css2401-and-2401_legacy-irci_master_2015070.patch
("atomisp2: css2401 and 2401_legacy-irci_master_20150701_0213")
Link to Intel's Android kernel patch.
## `coord = &me->config.internal_frame_origin_bqs_on_sctbl;` case
it was added on commit 4f744a573d ("media: atomisp: make
sh_css_sp_init_pipeline() ISP version independent") for ISP2401. Because
the upstreamed atomisp for the ISP2401 part is based on
irci_master_20150911_0724, hence the difference.
Because the upstreamed atomisp driver uses irci_master_20150911_0724
for ISP2401, revert the test back to `if (IS_ISP2401)`.
Fixes: 27333dadef ("media: atomisp: adjust some code at sh_css that could be broken")
Signed-off-by: Tsuchiya Yuto <kitakar@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d21ce8c2f7 ]
The function ia_css_mipi_is_source_port_valid() returns true if the port
is valid. So, we can't use the existing err variable as is.
To fix this issue while reusing that variable, invert the return value
when assigning it to the variable.
Fixes: 3c0538fbad ("media: atomisp: get rid of most checks for ISP2401 version")
Signed-off-by: Tsuchiya Yuto <kitakar@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f6b4fa2d2 ]
Currently, the `port >= N_CSI_PORTS || err` checks for ISP2400 are always
evaluated as true because the err variable is set to `-EINVAL` on
declaration but the variable is never used until the evaluation.
Looking at the diff of commit 3c0538fbad ("media: atomisp: get rid of
most checks for ISP2401 version"), the `port >= N_CSI_PORTS` check is
for ISP2400 and the err variable check is for ISP2401. Fix this issue
by adding ISP version test there accordingly.
Fixes: 3c0538fbad ("media: atomisp: get rid of most checks for ISP2401 version")
Signed-off-by: Tsuchiya Yuto <kitakar@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1921cd146 ]
When config.mode is IA_CSS_INPUT_MODE_BUFFERED_SENSOR, it rather needs
buffers. Fix it by inverting the return value.
Fixes: 3c0538fbad ("media: atomisp: get rid of most checks for ISP2401 version")
Signed-off-by: Tsuchiya Yuto <kitakar@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5bfbf65fcc ]
When comparing with intel-aero atomisp [1], it looks like
punit_ddr_dvfs_enable() should take `false` as an argument on mrfld_power
up case.
Code from the intel-aero kernel [1]:
int atomisp_mrfld_power_down(struct atomisp_device *isp)
{
[...]
/*WA:Enable DVFS*/
if (IS_CHT)
punit_ddr_dvfs_enable(true);
int atomisp_mrfld_power_up(struct atomisp_device *isp)
{
[...]
/*WA for PUNIT, if DVFS enabled, ISP timeout observed*/
if (IS_CHT)
punit_ddr_dvfs_enable(false);
This patch fixes the inverted argument as per the intel-aero code, as
well as its comment. While here, fix space issues for comments in
atomisp_mrfld_power().
Note that it does not seem to be possible to unify the up/down cases for
punit_ddr_dvfs_enable(), i.e., we can't do something like the following:
if (IS_CHT)
punit_ddr_dvfs_enable(!enable);
because according to the intel-aero code [1], the DVFS is disabled
before "writing 0x0 to ISPSSPM0 bit[1:0]" and the DVFS is enabled after
"writing 0x3 to ISPSSPM0 bit[1:0]".
[1] a1b673258f/drivers/media/pci/atomisp/atomisp_driver/atomisp_v4l2.c (L431-L514)
Fixes: 0f441fd70b ("media: atomisp: simplify the power down/up code")
Signed-off-by: Tsuchiya Yuto <kitakar@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce3015b721 ]
After the commit 9832e155f1 ("[media] media-device: split media
initialization and registration"), calling media_device_cleanup()
is needed it seems. However, currently it is missing for the module
unload path.
Note that for the probe failure path, it is already added in
atomisp_register_entities().
This patch adds the missing call of media_device_cleanup() in
atomisp_unregister_entities().
Fixes: a49d25364d ("staging/atomisp: Add support for the Intel IPU v2")
Signed-off-by: Tsuchiya Yuto <kitakar@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 16a2c3d540 ]
HTT_PPDU_STATS_CFG_PDEV_ID bit mask for target FW PPDU stats request message
was set as bit 8 to 15. Bit 8 is reserved for soc stats and pdev id starts from
bit 9. Hence change the bitmask as bit 9 to 15 and fill the proper pdev id in
the request message.
In commit 701e48a43e ("ath11k: add packet log support for QCA6390"), both
HTT_PPDU_STATS_CFG_PDEV_ID and pdev_mask were changed, but this pdev_mask
calculation is not valid for platforms which has multiple pdevs with 1 rxdma
per pdev, as this is writing same value(i.e. 2) for all pdevs. Hence fixed it
to consider pdev_idx as well, to make it compatible for both single and multi
pd cases.
Tested on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01092-QCAHKSWPL_SILICONZ-1
Tested on: IPQ6018 hw1.0 WLAN.HK.2.5.0.1-01067-QCAHKSWPL_SILICONZ-1
Fixes: 701e48a43e ("ath11k: add packet log support for QCA6390")
Co-developed-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Rameshkumar Sundaram <ramess@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-10-jouni@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9c5608faf ]
status.band is used in determination of status.rate -- for 5GHz on legacy
rates there is a linear shift between the BD descriptor's rate field and
the wcn36xx driver's rate table (wcn_5ghz_rates).
We have a special clause to populate status.band for hardware scan offload
frames. However, this block occurs after status.rate is already populated.
Correctly handle this dependency by moving the band block before the rate
block.
This patch addresses kernel warnings & missing scan results for 5GHz APs
that send their beacons/probe responses at the higher four legacy rates
(24-54 Mbps), when using hardware scan offload:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at net/mac80211/rx.c:4532 ieee80211_rx_napi+0x744/0x8d8
Modules linked in: wcn36xx [...]
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 4.19.107-g73909fa #1
Hardware name: Square, Inc. T2 (all variants) (DT)
Call trace:
dump_backtrace+0x0/0x148
show_stack+0x14/0x1c
dump_stack+0xb8/0xf0
__warn+0x2ac/0x2d8
warn_slowpath_null+0x44/0x54
ieee80211_rx_napi+0x744/0x8d8
ieee80211_tasklet_handler+0xa4/0xe0
tasklet_action_common+0xe0/0x118
tasklet_action+0x20/0x28
__do_softirq+0x108/0x1ec
irq_exit+0xd4/0xd8
__handle_domain_irq+0x84/0xbc
gic_handle_irq+0x4c/0xb8
el1_irq+0xe8/0x190
lpm_cpuidle_enter+0x220/0x260
cpuidle_enter_state+0x114/0x1c0
cpuidle_enter+0x34/0x48
do_idle+0x150/0x268
cpu_startup_entry+0x20/0x24
rest_init+0xd4/0xe0
start_kernel+0x398/0x430
---[ end trace ae28cb759352b403 ]---
Fixes: 8a27ca3947 ("wcn36xx: Correct band/freq reporting on RX")
Signed-off-by: Benjamin Li <benl@squareup.com>
Tested-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211104010548.1107405-2-benl@squareup.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89dcb1da61 ]
Right now we have a broken sequence where we enable DMA channel interrupts
which can be left enabled and never disabled if we hit an error path.
Worse still when we unload the driver, the DMA channel interrupt bits are
left intact. About the only saving grace here is that we do remember to
disable the wcnss interrupt when unload the driver.
Fixes: 8e84c25821 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211105122152.1580542-2-bryan.odonoghue@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 588b45c88a ]
Firmware can trigger a missed beacon indication, this is not the same as a
lost signal.
Flag to Linux the missed beacon and let the WiFi stack decide for itself if
the link is up or down by sending its own probe to determine this.
We should only be signalling the link is lost when the firmware indicates
Fixes: 8e84c25821 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027232529.657764-1-bryan.odonoghue@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f1ba8b0ee ]
An SMD capture from the downstream prima driver on WCN3680B shows the
following command sequence for connected scans:
- init_scan_req
- start_scan_req, channel 1
- end_scan_req, channel 1
- start_scan_req, channel 2
- ...
- end_scan_req, channel 3
- finish_scan_req
- init_scan_req
- start_scan_req, channel 4
- ...
- end_scan_req, channel 6
- finish_scan_req
- ...
- end_scan_req, channel 165
- finish_scan_req
Upstream currently never calls wcn36xx_smd_end_scan, and in some cases[1]
still sends finish_scan_req twice in a row or before init_scan_req. A
typical connected scan looks like this:
- init_scan_req
- start_scan_req, channel 1
- finish_scan_req
- init_scan_req
- start_scan_req, channel 2
- ...
- start_scan_req, channel 165
- finish_scan_req
- finish_scan_req
This patch cleans up scanning so that init/finish and start/end are always
paired together and correctly nested.
- init_scan_req
- start_scan_req, channel 1
- end_scan_req, channel 1
- finish_scan_req
- init_scan_req
- start_scan_req, channel 2
- end_scan_req, channel 2
- ...
- start_scan_req, channel 165
- end_scan_req, channel 165
- finish_scan_req
Note that upstream will not do batching of 3 active-probe scans before
returning to the operating channel, and this patch does not change that.
To match downstream in this aspect, adjust IEEE80211_PROBE_DELAY and/or
the 125ms max off-channel time in ieee80211_scan_state_decision.
[1]: commit d195d7aac0 ("wcn36xx: Ensure finish scan is not requested
before start scan") addressed one case of finish_scan_req being sent
without a preceding init_scan_req (the case of the operating channel
coinciding with the first scan channel); two other cases are:
1) if SW scan is started and aborted immediately, without scanning any
channels, we send a finish_scan_req without ever sending init_scan_req,
and
2) as SW scan logic always returns us to the operating channel before
calling wcn36xx_sw_scan_complete, finish_scan_req is always sent twice
at the end of a SW scan
Fixes: 8e84c25821 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware")
Signed-off-by: Benjamin Li <benl@squareup.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027170306.555535-4-benl@squareup.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ca011ef4a ]
The driver, once it found a divider, tries to round it up by increasing
the least significant bit of the fractional part by one when the
round_up argument is set and there's a remainder.
However, since it increases the divider it will actually reduce the
clock rate below what we were asking for, leading to issues with
clk_set_min_rate() that will complain that our rounded clock rate is
below the minimum of the rate.
Since the dividers are fairly precise already, let's remove that part so
that we can have clk_set_min_rate() working.
This is effectively a revert of 9c95b32ca0 ("clk: bcm2835: add a round
up ability to the clock divisor").
Fixes: 9c95b32ca0 ("clk: bcm2835: add a round up ability to the clock divisor")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Tested-by: Nicolas Saenz Julienne <nsaenz@kernel.org> # boot and basic functionality
Tested-by: Michael Stapelberg <michael@stapelberg.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210922125419.4125779-3-maxime@cerno.tech
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5517357a47 ]
The driver currently tries to pick the closest rate that is lower than
the rate being requested.
This causes an issue with clk_set_min_rate() since it actively checks
for the rounded rate to be above the minimum that was just set.
Let's change the logic a bit to pick the closest rate to the requested
rate, no matter if it's actually higher or lower.
Fixes: 6d18b8adbe ("clk: bcm2835: Support for clock parent selection")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Tested-by: Nicolas Saenz Julienne <nsaenz@kernel.org> # boot and basic functionality
Tested-by: Michael Stapelberg <michael@stapelberg.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210922125419.4125779-2-maxime@cerno.tech
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a7ca7459d ]
I got a kernel BUG report when doing fault injection test:
------------[ cut here ]------------
kernel BUG at lib/list_debug.c:45!
...
RIP: 0010:__list_del_entry_valid.cold+0x12/0x4d
...
Call Trace:
proto_unregister+0x83/0x220
cmtp_cleanup_sockets+0x37/0x40 [cmtp]
cmtp_exit+0xe/0x1f [cmtp]
do_syscall_64+0x35/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
If cmtp_init_sockets() in cmtp_init() fails, cmtp_init() still returns
success. This will cause a kernel bug when accessing uncreated ctmp
related data when the module exits.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e584cdc154 upstream.
Since commit 43c2de1002 ("drm/rockchip: dsi: move all lane config except
LCDC mux to bind()"), we perform most HW configuration in the bind()
function. This configuration may be lost on suspend/resume, so we
need to call it again. That may lead to errors like this after system
suspend/resume:
dw-mipi-dsi-rockchip ff968000.mipi: failed to write command FIFO
panel-kingdisplay-kd097d04 ff960000.mipi.0: failed write init cmds: -110
Tested on Acer Chromebook Tab 10 (RK3399 Gru-Scarlet).
Note that early mailing list versions of this driver borrowed Rockchip's
downstream/BSP solution, to do HW configuration in mode_set() (which
*is* called at the appropriate pre-enable() times), but that was
discarded along the way. I've avoided that still, because mode_set()
documentation doesn't suggest this kind of purpose as far as I can tell.
Fixes: 43c2de1002 ("drm/rockchip: dsi: move all lane config except LCDC mux to bind()")
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210928143413.v3.2.I4e9d93aadb00b1ffc7d506e3186a25492bf0b732@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 514db87192 upstream.
In commit 43c2de1002 ("drm/rockchip: dsi: move all lane config except
LCDC mux to bind()"), we moved most HW configuration to bind(), but we
didn't move the runtime PM management. Therefore, depending on initial
boot state, runtime-PM workqueue delays, and other timing factors, we
may disable our power domain in between the hardware configuration
(bind()) and when we enable the display. This can cause us to lose
hardware state and fail to configure our display. For example:
dw-mipi-dsi-rockchip ff968000.mipi: failed to write command FIFO
panel-innolux-p079zca ff960000.mipi.0: failed to write command 0
or:
dw-mipi-dsi-rockchip ff968000.mipi: failed to write command FIFO
panel-kingdisplay-kd097d04 ff960000.mipi.0: failed write init cmds: -110
We should match the runtime PM to the lifetime of the bind()/unbind()
cycle.
Tested on Acer Chrometab 10 (RK3399 Gru-Scarlet), with panel drivers
built either as modules or built-in.
Side notes: it seems one is more likely to see this problem when the
panel driver is built into the kernel. I've also seen this problem
bisect down to commits that simply changed Kconfig dependencies, because
it changed the order in which driver init functions were compiled into
the kernel, and therefore the ordering and timing of built-in device
probe.
Fixes: 43c2de1002 ("drm/rockchip: dsi: move all lane config except LCDC mux to bind()")
Link: https://lore.kernel.org/linux-rockchip/9aedfb528600ecf871885f7293ca4207c84d16c1.camel@gmail.com/
Reported-by: <aleksandr.o.makarov@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210928143413.v3.1.Ic2904d37f30013a7f3d8476203ad3733c186827e@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit acf20ed020 ]
I got a null-ptr-deref report:
[drm:drm_dev_init [drm]] *ERROR* Cannot allocate anonymous inode: -12
==================================================================
BUG: KASAN: null-ptr-deref in iput+0x3c/0x4a0
...
Call Trace:
dump_stack_lvl+0x6c/0x8b
kasan_report.cold+0x64/0xdb
__asan_load8+0x69/0x90
iput+0x3c/0x4a0
drm_dev_init_release+0x39/0xb0 [drm]
drm_managed_release+0x158/0x2d0 [drm]
drm_dev_init+0x3a7/0x4c0 [drm]
__devm_drm_dev_alloc+0x55/0xd0 [drm]
mi0283qt_probe+0x8a/0x2b5 [mi0283qt]
spi_probe+0xeb/0x130
...
entry_SYSCALL_64_after_hwframe+0x44/0xae
If drm_fs_inode_new() fails in drm_dev_init(), dev->anon_inode will point
to PTR_ERR(...) instead of NULL. This will result in null-ptr-deref when
drm_fs_inode_free(dev->anon_inode) is called.
drm_dev_init()
drm_fs_inode_new() // fail, dev->anon_inode = PTR_ERR(...)
drm_managed_release()
drm_dev_init_release()
drm_fs_inode_free() // access non-existent anon_inode
Define a temp variable and assign it to dev->anon_inode if the temp
variable is not PTR_ERR.
Fixes: 2cbf7fc671 ("drm: Use drmm_ for drm_dev_init cleanup")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211013114139.4042207-1-wanghai38@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5ff291098 ]
In order to group sockets being connected using L2CAP_MODE_EXT_FLOWCTL
the pid is used but sk_peer_pid was not being initialized as it is
currently only done for af_unix.
Fixes: b48596d1dc ("Bluetooth: L2CAP: Add get_peer_pid callback")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 62c9827cbb upstream.
Fix a data race in commit 779750d20b ("shmem: split huge pages beyond
i_size under memory pressure").
Here are call traces causing race:
Call Trace 1:
shmem_unused_huge_shrink+0x3ae/0x410
? __list_lru_walk_one.isra.5+0x33/0x160
super_cache_scan+0x17c/0x190
shrink_slab.part.55+0x1ef/0x3f0
shrink_node+0x10e/0x330
kswapd+0x380/0x740
kthread+0xfc/0x130
? mem_cgroup_shrink_node+0x170/0x170
? kthread_create_on_node+0x70/0x70
ret_from_fork+0x1f/0x30
Call Trace 2:
shmem_evict_inode+0xd8/0x190
evict+0xbe/0x1c0
do_unlinkat+0x137/0x330
do_syscall_64+0x76/0x120
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
A simple explanation:
Image there are 3 items in the local list (@list). In the first
traversal, A is not deleted from @list.
1) A->B->C
^
|
pos (leave)
In the second traversal, B is deleted from @list. Concurrently, A is
deleted from @list through shmem_evict_inode() since last reference
counter of inode is dropped by other thread. Then the @list is corrupted.
2) A->B->C
^ ^
| |
evict pos (drop)
We should make sure the inode is either on the global list or deleted from
any local list before iput().
Fixed by moving inodes back to global list before we put them.
[akpm@linux-foundation.org: coding style fixes]
Link: https://lkml.kernel.org/r/20211125064502.99983-1-ligang.bdlg@bytedance.com
Fixes: 779750d20b ("shmem: split huge pages beyond i_size under memory pressure")
Signed-off-by: Gang Li <ligang.bdlg@bytedance.com>
Reviewed-by: Muchun Song <songmuchun@bytedance.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c4dc63f003 upstream.
In kdump kernel of x86_64, page allocation failure is observed:
kworker/u2:2: page allocation failure: order:0, mode:0xcc1(GFP_KERNEL|GFP_DMA), nodemask=(null),cpuset=/,mems_allowed=0
CPU: 0 PID: 55 Comm: kworker/u2:2 Not tainted 5.16.0-rc4+ #5
Hardware name: AMD Dinar/Dinar, BIOS RDN1505B 06/05/2013
Workqueue: events_unbound async_run_entry_fn
Call Trace:
<TASK>
dump_stack_lvl+0x48/0x5e
warn_alloc.cold+0x72/0xd6
__alloc_pages_slowpath.constprop.0+0xc69/0xcd0
__alloc_pages+0x1df/0x210
new_slab+0x389/0x4d0
___slab_alloc+0x58f/0x770
__slab_alloc.constprop.0+0x4a/0x80
kmem_cache_alloc_trace+0x24b/0x2c0
sr_probe+0x1db/0x620
......
device_add+0x405/0x920
......
__scsi_add_device+0xe5/0x100
ata_scsi_scan_host+0x97/0x1d0
async_run_entry_fn+0x30/0x130
process_one_work+0x1e8/0x3c0
worker_thread+0x50/0x3b0
? rescuer_thread+0x350/0x350
kthread+0x16b/0x190
? set_kthread_struct+0x40/0x40
ret_from_fork+0x22/0x30
</TASK>
Mem-Info:
......
The above failure happened when calling kmalloc() to allocate buffer with
GFP_DMA. It requests to allocate slab page from DMA zone while no managed
pages at all in there.
sr_probe()
--> get_capabilities()
--> buffer = kmalloc(512, GFP_KERNEL | GFP_DMA);
Because in the current kernel, dma-kmalloc will be created as long as
CONFIG_ZONE_DMA is enabled. However, kdump kernel of x86_64 doesn't have
managed pages on DMA zone since commit 6f599d8423 ("x86/kdump: Always
reserve the low 1M when the crashkernel option is specified"). The
failure can be always reproduced.
For now, let's mute the warning of allocation failure if requesting pages
from DMA zone while no managed pages.
[akpm@linux-foundation.org: fix warning]
Link: https://lkml.kernel.org/r/20211223094435.248523-4-bhe@redhat.com
Fixes: 6f599d8423 ("x86/kdump: Always reserve the low 1M when the crashkernel option is specified")
Signed-off-by: Baoquan He <bhe@redhat.com>
Acked-by: John Donnelly <john.p.donnelly@oracle.com>
Reviewed-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: David Hildenbrand <david@redhat.com>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a674e48c54 upstream.
Currently three dma atomic pools are initialized as long as the relevant
kernel codes are built in. While in kdump kernel of x86_64, this is not
right when trying to create atomic_pool_dma, because there's no managed
pages in DMA zone. In the case, DMA zone only has low 1M memory
presented and locked down by memblock allocator. So no pages are added
into buddy of DMA zone. Please check commit f1d4d47c58 ("x86/setup:
Always reserve the first 1M of RAM").
Then in kdump kernel of x86_64, it always prints below failure message:
DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
swapper/0: page allocation failure: order:5, mode:0xcc1(GFP_KERNEL|GFP_DMA), nodemask=(null),cpuset=/,mems_allowed=0
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.13.0-0.rc5.20210611git929d931f2b40.42.fc35.x86_64 #1
Hardware name: Dell Inc. PowerEdge R910/0P658H, BIOS 2.12.0 06/04/2018
Call Trace:
dump_stack+0x7f/0xa1
warn_alloc.cold+0x72/0xd6
__alloc_pages_slowpath.constprop.0+0xf29/0xf50
__alloc_pages+0x24d/0x2c0
alloc_page_interleave+0x13/0xb0
atomic_pool_expand+0x118/0x210
__dma_atomic_pool_init+0x45/0x93
dma_atomic_pool_init+0xdb/0x176
do_one_initcall+0x67/0x320
kernel_init_freeable+0x290/0x2dc
kernel_init+0xa/0x111
ret_from_fork+0x22/0x30
Mem-Info:
......
DMA: failed to allocate 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocation
DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
Here, let's check if DMA zone has managed pages, then create
atomic_pool_dma if yes. Otherwise just skip it.
Link: https://lkml.kernel.org/r/20211223094435.248523-3-bhe@redhat.com
Fixes: 6f599d8423 ("x86/kdump: Always reserve the low 1M when the crashkernel option is specified")
Signed-off-by: Baoquan He <bhe@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: John Donnelly <john.p.donnelly@oracle.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: David Rientjes <rientjes@google.com>
Cc: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 62b3107073 upstream.
Patch series "Handle warning of allocation failure on DMA zone w/o
managed pages", v4.
**Problem observed:
On x86_64, when crash is triggered and entering into kdump kernel, page
allocation failure can always be seen.
---------------------------------
DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
swapper/0: page allocation failure: order:5, mode:0xcc1(GFP_KERNEL|GFP_DMA), nodemask=(null),cpuset=/,mems_allowed=0
CPU: 0 PID: 1 Comm: swapper/0
Call Trace:
dump_stack+0x7f/0xa1
warn_alloc.cold+0x72/0xd6
......
__alloc_pages+0x24d/0x2c0
......
dma_atomic_pool_init+0xdb/0x176
do_one_initcall+0x67/0x320
? rcu_read_lock_sched_held+0x3f/0x80
kernel_init_freeable+0x290/0x2dc
? rest_init+0x24f/0x24f
kernel_init+0xa/0x111
ret_from_fork+0x22/0x30
Mem-Info:
------------------------------------
***Root cause:
In the current kernel, it assumes that DMA zone must have managed pages
and try to request pages if CONFIG_ZONE_DMA is enabled. While this is not
always true. E.g in kdump kernel of x86_64, only low 1M is presented and
locked down at very early stage of boot, so that this low 1M won't be
added into buddy allocator to become managed pages of DMA zone. This
exception will always cause page allocation failure if page is requested
from DMA zone.
***Investigation:
This failure happens since below commit merged into linus's tree.
1a6a9044b9 x86/setup: Remove CONFIG_X86_RESERVE_LOW and reservelow= options
23721c8e92 x86/crash: Remove crash_reserve_low_1M()
f1d4d47c58 x86/setup: Always reserve the first 1M of RAM
7c321eb2b8 x86/kdump: Remove the backup region handling
6f599d8423 x86/kdump: Always reserve the low 1M when the crashkernel option is specified
Before them, on x86_64, the low 640K area will be reused by kdump kernel.
So in kdump kernel, the content of low 640K area is copied into a backup
region for dumping before jumping into kdump. Then except of those firmware
reserved region in [0, 640K], the left area will be added into buddy
allocator to become available managed pages of DMA zone.
However, after above commits applied, in kdump kernel of x86_64, the low
1M is reserved by memblock, but not released to buddy allocator. So any
later page allocation requested from DMA zone will fail.
At the beginning, if crashkernel is reserved, the low 1M need be locked
down because AMD SME encrypts memory making the old backup region
mechanims impossible when switching into kdump kernel.
Later, it was also observed that there are BIOSes corrupting memory
under 1M. To solve this, in commit f1d4d47c58, the entire region of
low 1M is always reserved after the real mode trampoline is allocated.
Besides, recently, Intel engineer mentioned their TDX (Trusted domain
extensions) which is under development in kernel also needs to lock down
the low 1M. So we can't simply revert above commits to fix the page allocation
failure from DMA zone as someone suggested.
***Solution:
Currently, only DMA atomic pool and dma-kmalloc will initialize and
request page allocation with GFP_DMA during bootup.
So only initializ DMA atomic pool when DMA zone has available managed
pages, otherwise just skip the initialization.
For dma-kmalloc(), for the time being, let's mute the warning of
allocation failure if requesting pages from DMA zone while no manged
pages. Meanwhile, change code to use dma_alloc_xx/dma_map_xx API to
replace kmalloc(GFP_DMA), or do not use GFP_DMA when calling kmalloc() if
not necessary. Christoph is posting patches to fix those under
drivers/scsi/. Finally, we can remove the need of dma-kmalloc() as people
suggested.
This patch (of 3):
In some places of the current kernel, it assumes that dma zone must have
managed pages if CONFIG_ZONE_DMA is enabled. While this is not always
true. E.g in kdump kernel of x86_64, only low 1M is presented and locked
down at very early stage of boot, so that there's no managed pages at all
in DMA zone. This exception will always cause page allocation failure if
page is requested from DMA zone.
Here add function has_managed_dma() and the relevant helper functions to
check if there's DMA zone with managed pages. It will be used in later
patches.
Link: https://lkml.kernel.org/r/20211223094435.248523-1-bhe@redhat.com
Link: https://lkml.kernel.org/r/20211223094435.248523-2-bhe@redhat.com
Fixes: 6f599d8423 ("x86/kdump: Always reserve the low 1M when the crashkernel option is specified")
Signed-off-by: Baoquan He <bhe@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: John Donnelly <john.p.donnelly@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Christoph Lameter <cl@linux.com>
Cc: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e445375882 upstream.
Like other SATA controller chips in the Marvell 88SE91xx series, the
Marvell 88SE9125 has the same DMA requester ID hardware bug that prevents
it from working under IOMMU. Add it to the list of devices that need the
quirk.
Without this patch, device initialization fails with DMA errors:
ata8: softreset failed (1st FIS failed)
DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Write NO_PASID] Request device [03:00.1] fault addr 0xfffc0000 [fault reason 0x02] Present bit in context entry is clear
DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Read NO_PASID] Request device [03:00.1] fault addr 0xfffc0000 [fault reason 0x02] Present bit in context entry is clear
After applying the patch, the controller can be successfully initialized:
ata8: SATA link up 1.5 Gbps (SStatus 113 SControl 330)
ata8.00: ATAPI: PIONEER BD-RW BDR-207M, 1.21, max UDMA/100
ata8.00: configured for UDMA/100
scsi 7:0:0:0: CD-ROM PIONEER BD-RW BDR-207M 1.21 PQ: 0 ANSI: 5
Link: https://lore.kernel.org/r/YahpKVR+McJVDdkD@work
Reported-by: Sam Bingner <sam@bingner.com>
Tested-by: Sam Bingner <sam@bingner.com>
Tested-by: Yifeng Li <tomli@tomli.me>
Signed-off-by: Yifeng Li <tomli@tomli.me>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d5185965c3 upstream.
Host1x DMA buffer isn't mapped properly when CONFIG_ARM_DMA_USE_IOMMU=y.
The memory management code of Host1x driver has a longstanding overhaul
overdue and it's not obvious where the problem is in this case. Hence
let's add back the old workaround which we already had sometime before.
It explicitly detaches Host1x device from the offending implicit IOMMU
domain. This fixes a completely broken Host1x DMA in case of ARM32
multiplatform kernel config.
Cc: stable@vger.kernel.org
Fixes: af1cbfb9bf ("gpu: host1x: Support DMA mapping of buffers")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a556cfe4ca upstream.
In __arm_v7s_alloc_table function:
iommu call kmem_cache_alloc to allocate page table, this function
allocate memory may fail, when kmem_cache_alloc fails to allocate
table, call virt_to_phys will be abnomal and return unexpected phys
and goto out_free, then call kmem_cache_free to release table will
trigger KE, __get_free_pages and free_pages have similar problem,
so add error handle for page table allocation failure.
Fixes: 29859aeb8a ("iommu/io-pgtable-arm-v7s: Abort allocation when table address overflows the PTE")
Signed-off-by: Yunfei Wang <yf.wang@mediatek.com>
Cc: <stable@vger.kernel.org> # 5.10.*
Acked-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20211207113315.29109-1-yf.wang@mediatek.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 713bdfa10b upstream.
The en/disable_irq() functions keep track of the 'depth': i.e. if
interrupts are disabled twice, then it needs to enable_irq() calls to
enable them again. The cec-pin framework didn't take this into accound
and could disable irqs multiple times, and it expected that a single
enable_irq() would enable them again.
Move all calls to en/disable_irq() to the kthread where it is easy
to keep track of the current irq state and ensure that multiple
en/disable_irq calls never happen.
If interrupts where disabled twice, then they would never turn on
again, leaving the CEC adapter in a dead state.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 865463fc03 (media: cec-pin: add error injection support)
Cc: <stable@vger.kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7b77ebe6d upstream.
This fixes a problem where closing the tuner would leave it in a state
where it would not tune to any channel when reopened. This problem was
discovered as part of https://github.com/hselasky/webcamd/issues/16.
Since adap->id is 0 or 1, this bit-shift overflows, which is undefined
behavior. The driver still worked in practice as the overflow would in
most environments result in 0, which rendered the line a no-op. When
running the driver as part of webcamd however, the overflow could lead
to 0xff due to optimizations by the compiler, which would, in the end,
improperly shut down the tuner.
The bug is a regression introduced in the commit referenced below. The
present patch causes identical behavior to before that commit for
adap->id equal to 0 or 1. The driver does not contain support for
dib0700 devices with more adapters, assuming such even exist.
Tests have been performed with the Xbox One Digital TV Tuner on amd64.
Not all dib0700 devices are expected to be affected by the regression;
this code path is only taken by those with incorrect endpoint numbers.
Link: https://lore.kernel.org/linux-media/1d2fc36d94ced6f67c7cc21dcc469d5e5bdd8201.1632689033.git.mchehab+huawei@kernel.org
Cc: stable@vger.kernel.org
Fixes: 7757ddda6f ("[media] DiB0700: add function to change I2C-speed")
Signed-off-by: Michael Kuron <michael.kuron@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f71d272ad4 upstream.
USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.
Use the common control-message timeout define for the five-second
timeouts.
Fixes: 38f993ad8b ("V4L/DVB (8125): This driver adds support for the Sensoray 2255 devices.")
Cc: stable@vger.kernel.org # 2.6.27
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd1798a387 upstream.
USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.
Note that the driver was multiplying some of the timeout values with HZ
twice resulting in 3000-second timeouts with HZ=1000.
Also note that two of the timeout defines are currently unused.
Fixes: 2154be651b ("[media] redrat3: new rc-core IR transceiver device driver")
Cc: stable@vger.kernel.org # 3.0
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd9d9377ed upstream.
If V4L2_CAP_READWRITE is not set, then readbuffers must be set to 0,
otherwise v4l2-compliance will complain.
A note on the Fixes tag below: this patch does not really fix that commit,
but it can be applied from that commit onwards. For older code there is no
guarantee that device_caps is set, so even though this patch would apply,
it will not work reliably.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 049e684f2d (media: v4l2-dev: fix WARN_ON(!vdev->device_caps))
Cc: <stable@vger.kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de0244ae40 upstream.
Ammar Faizi reported that our exit code handling is wrong. We truncate
it to the lowest 8 bits but the syscall itself is expected to take a
regular 32-bit signed integer, not an unsigned char. It's the kernel
that later truncates it to the lowest 8 bits. The difference is visible
in strace, where the program below used to show exit(255) instead of
exit(-1):
int main(void)
{
return -1;
}
This patch applies the fix to all archs. x86_64, i386, arm64, armv7 and
mips were all tested and confirmed to work fine now. Risc-v was not
tested but the change is trivial and exactly the same as for other archs.
Reported-by: Ammar Faizi <ammar.faizi@students.amikom.ac.id>
Cc: stable@vger.kernel.org
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ebbe0d8a44 upstream.
After re-checking in the spec and comparing stack offsets with glibc,
The last pushed argument must be 16-byte aligned (i.e. aligned before the
call) so that in the callee esp+4 is multiple of 16, so the principle is
the 32-bit equivalent to what Ammar fixed for x86_64. It's possible that
32-bit code using SSE2 or MMX could have been affected. In addition the
frame pointer ought to be zero at the deepest level.
Link: https://gitlab.com/x86-psABIs/i386-ABI/-/wikis/Intel386-psABI
Cc: Ammar Faizi <ammar.faizi@students.amikom.ac.id>
Cc: stable@vger.kernel.org
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 937ed91c71 upstream.
Before this patch, the `_start` function looks like this:
```
0000000000001170 <_start>:
1170: pop %rdi
1171: mov %rsp,%rsi
1174: lea 0x8(%rsi,%rdi,8),%rdx
1179: and $0xfffffffffffffff0,%rsp
117d: sub $0x8,%rsp
1181: call 1000 <main>
1186: movzbq %al,%rdi
118a: mov $0x3c,%rax
1191: syscall
1193: hlt
1194: data16 cs nopw 0x0(%rax,%rax,1)
119f: nop
```
Note the "and" to %rsp with $-16, it makes the %rsp be 16-byte aligned,
but then there is a "sub" with $0x8 which makes the %rsp no longer
16-byte aligned, then it calls main. That's the bug!
What actually the x86-64 System V ABI mandates is that right before the
"call", the %rsp must be 16-byte aligned, not after the "call". So the
"sub" with $0x8 here breaks the alignment. Remove it.
An example where this rule matters is when the callee needs to align
its stack at 16-byte for aligned move instruction, like `movdqa` and
`movaps`. If the callee can't align its stack properly, it will result
in segmentation fault.
x86-64 System V ABI also mandates the deepest stack frame should be
zero. Just to be safe, let's zero the %rbp on startup as the content
of %rbp may be unspecified when the program starts. Now it looks like
this:
```
0000000000001170 <_start>:
1170: pop %rdi
1171: mov %rsp,%rsi
1174: lea 0x8(%rsi,%rdi,8),%rdx
1179: xor %ebp,%ebp # zero the %rbp
117b: and $0xfffffffffffffff0,%rsp # align the %rsp
117f: call 1000 <main>
1184: movzbq %al,%rdi
1188: mov $0x3c,%rax
118f: syscall
1191: hlt
1192: data16 cs nopw 0x0(%rax,%rax,1)
119d: nopl (%rax)
```
Cc: Bedirhan KURT <windowz414@gnuweeb.org>
Cc: Louvian Lyndal <louvianlyndal@gmail.com>
Reported-by: Peter Cordes <peter@cordes.ca>
Signed-off-by: Ammar Faizi <ammar.faizi@students.amikom.ac.id>
[wt: I did this on purpose due to a misunderstanding of the spec, other
archs will thus have to be rechecked, particularly i386]
Cc: stable@vger.kernel.org
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c494ca4d3 upstream.
"Stolen memory" is memory set aside for use by an Intel integrated GPU.
The intel_graphics_quirks() early quirk reserves this memory when it is
called for a GPU that appears in the intel_early_ids[] table of integrated
GPUs.
Previously intel_graphics_quirks() was marked as QFLAG_APPLY_ONCE, so it
was called only for the first Intel GPU found. If a discrete GPU happened
to be enumerated first, intel_graphics_quirks() was called for it but not
for any integrated GPU found later. Therefore, stolen memory for such an
integrated GPU was never reserved.
For example, this problem occurs in this Alderlake-P (integrated) + DG2
(discrete) topology where the DG2 is found first, but stolen memory is
associated with the integrated GPU:
- 00:01.0 Bridge
`- 03:00.0 DG2 discrete GPU
- 00:02.0 Integrated GPU (with stolen memory)
Remove the QFLAG_APPLY_ONCE flag and call intel_graphics_quirks() for every
Intel GPU. Reserve stolen memory for the first GPU that appears in
intel_early_ids[].
[bhelgaas: commit log, add code comment, squash in
https://lore.kernel.org/r/20220118190558.2ququ4vdfjuahicm@ldmartin-desk2]
Link: https://lore.kernel.org/r/20220114002843.2083382-1-lucas.demarchi@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c9d709965 upstream.
The function nand_davinci_read_page_hwecc_oob_first() first reads the
OOB data, extracts the ECC information, programs the ECC hardware before
reading the actual data in a loop.
Right after the OOB data was read, it called nand_read_page_op() to
reset the read cursor to the beginning of the page. This caused the
first page to be read twice: in that call, and later in the loop.
Address that issue by changing the call to nand_read_page_op() to
nand_change_read_column_op(), which will only reset the read cursor.
Cc: <stable@vger.kernel.org> # v5.2
Fixes: a0ac778eb8 ("mtd: rawnand: ingenic: Add support for the JZ4740")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211016132228.40254-2-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f53d4c109a upstream.
gpmi_io clock needs to be gated off when changing the parent/dividers of
enfc_clk_root (i.MX6Q/i.MX6UL) respectively qspi2_clk_root (i.MX6SX).
Otherwise this rate change can lead to an unresponsive GPMI core which
results in DMA timeouts and failed driver probe:
[ 4.072318] gpmi-nand 112000.gpmi-nand: DMA timeout, last DMA
...
[ 4.370355] gpmi-nand 112000.gpmi-nand: Chip: 0, Error -110
...
[ 4.375988] gpmi-nand 112000.gpmi-nand: Chip: 0, Error -22
[ 4.381524] gpmi-nand 112000.gpmi-nand: Error in ECC-based read: -22
[ 4.387988] gpmi-nand 112000.gpmi-nand: Chip: 0, Error -22
[ 4.393535] gpmi-nand 112000.gpmi-nand: Chip: 0, Error -22
...
Other than stated in i.MX 6 erratum ERR007117, it should be sufficient
to gate only gpmi_io because all other bch/nand clocks are derived from
different clock roots.
The i.MX6 reference manuals state that changing clock muxers can cause
glitches but are silent about changing dividers. But tests showed that
these glitches can definitely happen on i.MX6ULL. For i.MX7D/8MM in turn,
the manual guarantees that no glitches can happen when changing
dividers.
Co-developed-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Christian Eggers <ceggers@arri.de>
Cc: stable@vger.kernel.org
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211102202022.15551-2-ceggers@arri.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dded08927c upstream.
Syzbot detected a NULL pointer dereference of nfc_llcp_sock->dev pointer
(which is a 'struct nfc_dev *') with calls to llcp_sock_sendmsg() after
a failed llcp_sock_bind(). The message being sent is a SOCK_DGRAM.
KASAN report:
BUG: KASAN: null-ptr-deref in nfc_alloc_send_skb+0x2d/0xc0
Read of size 4 at addr 00000000000005c8 by task llcp_sock_nfc_a/899
CPU: 5 PID: 899 Comm: llcp_sock_nfc_a Not tainted 5.16.0-rc6-next-20211224-00001-gc6437fbf18b0 #125
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-2 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x45/0x59
? nfc_alloc_send_skb+0x2d/0xc0
__kasan_report.cold+0x117/0x11c
? mark_lock+0x480/0x4f0
? nfc_alloc_send_skb+0x2d/0xc0
kasan_report+0x38/0x50
nfc_alloc_send_skb+0x2d/0xc0
nfc_llcp_send_ui_frame+0x18c/0x2a0
? nfc_llcp_send_i_frame+0x230/0x230
? __local_bh_enable_ip+0x86/0xe0
? llcp_sock_connect+0x470/0x470
? llcp_sock_connect+0x470/0x470
sock_sendmsg+0x8e/0xa0
____sys_sendmsg+0x253/0x3f0
...
The issue was visible only with multiple simultaneous calls to bind() and
sendmsg(), which resulted in most of the bind() calls to fail. The
bind() was failing on checking if there is available WKS/SDP/SAP
(respective bit in 'struct nfc_llcp_local' fields). When there was no
available WKS/SDP/SAP, the bind returned error but the sendmsg() to such
socket was able to trigger mentioned NULL pointer dereference of
nfc_llcp_sock->dev.
The code looks simply racy and currently it protects several paths
against race with checks for (!nfc_llcp_sock->local) which is NULL-ified
in error paths of bind(). The llcp_sock_sendmsg() did not have such
check but called function nfc_llcp_send_ui_frame() had, although not
protected with lock_sock().
Therefore the race could look like (same socket is used all the time):
CPU0 CPU1
==== ====
llcp_sock_bind()
- lock_sock()
- success
- release_sock()
- return 0
llcp_sock_sendmsg()
- lock_sock()
- release_sock()
llcp_sock_bind(), same socket
- lock_sock()
- error
- nfc_llcp_send_ui_frame()
- if (!llcp_sock->local)
- llcp_sock->local = NULL
- nfc_put_device(dev)
- dereference llcp_sock->dev
- release_sock()
- return -ERRNO
The nfc_llcp_send_ui_frame() checked llcp_sock->local outside of the
lock, which is racy and ineffective check. Instead, its caller
llcp_sock_sendmsg(), should perform the check inside lock_sock().
Reported-and-tested-by: syzbot+7f23bcddf626e0593a39@syzkaller.appspotmail.com
Fixes: b874dec21d ("NFC: Implement LLCP connection less Tx path")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77900c45ee upstream.
In fuzzed image, SSA table may indicate that a data block belongs to
invalid node, which node ID is out-of-range (0, 1, 2 or max_nid), in
order to avoid migrating inconsistent data in such corrupted image,
let's do sanity check anyway before data block migration.
Cc: stable@vger.kernel.org
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 20f3cf5f86 upstream.
If we ever see a touch report with contact count data we initialize
several variables used to read the contact count in the pre-report
phase. These variables are never reset if we process a report which
doesn't contain a contact count, however. This can cause the pre-
report function to trigger a read of arbitrary memory (e.g. NULL
if we're lucky) and potentially crash the driver.
This commit restores resetting of the variables back to default
"none" values that were used prior to the commit mentioned
below.
Link: https://github.com/linuxwacom/input-wacom/issues/276
Fixes: 003f50ab67 (HID: wacom: Update last_slot_field during pre_report phase)
CC: stable@vger.kernel.org
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df03e9bd6d upstream.
AES hardware may internally re-classify a contact that it thought was
intentional as a palm. Intentional contacts are reported as "down" with
the confidence bit set. When this re-classification occurs, however, the
state transitions to "up" with the confidence bit cleared. This kind of
transition appears to be legal according to Microsoft docs, but we do
not handle it correctly. Because the confidence bit is clear, we don't
call `wacom_wac_finger_slot` and update userspace. This causes hung
touches that confuse userspace and interfere with pen arbitration.
This commit adds a special case to ignore the confidence flag if a contact
is reported as removed. This ensures we do not leave a hung touch if one
of these re-classification events occured. Ideally we'd have some way to
also let userspace know that the touch has been re-classified as a palm
and needs to be canceled, but that's not possible right now :)
Link: https://github.com/linuxwacom/input-wacom/issues/288
Fixes: 7fb0413baa (HID: wacom: Use "Confidence" flag to prevent reporting invalid contacts)
CC: stable@vger.kernel.org
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 546e41ac99 upstream.
These two values go hand-in-hand and must be valid for the driver to
behave correctly. We are currently lazy about updating the values and
rely on the "expected" code flow to take care of making sure they're
valid at the point they're needed. The "expected" flow changed somewhat
with commit f8b6a74719 ("HID: wacom: generic: Support multiple tools
per report"), however. This led to problems with the DTH-2452 due (in
part) to *all* contacts being fully processed -- even those past the
expected contact count. Specifically, the received count gets reset to
0 once all expected fingers are processed, but not the expected count.
The rest of the contacts in the report are then *also* processed since
now the driver thinks we've only processed 0 of N expected contacts.
Later commits such as 7fb0413baa (HID: wacom: Use "Confidence" flag to
prevent reporting invalid contacts) worked around the DTH-2452 issue by
skipping the invalid contacts at the end of the report, but this is not
a complete fix. The confidence flag cannot be relied on when a contact
is removed (see the following patch), and dealing with that condition
re-introduces the DTH-2452 issue unless we also address this contact
count laziness. By resetting expected and received counts at the same
time we ensure the driver understands that there are 0 more contacts
expected in the report. Similarly, we also make sure to reset the
received count if for some reason we're out of sync in the pre-report
phase.
Link: https://github.com/linuxwacom/input-wacom/issues/288
Fixes: f8b6a74719 ("HID: wacom: generic: Support multiple tools per report")
CC: stable@vger.kernel.org
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ea5763fb7 upstream.
uhid has to run hid_add_device() from workqueue context while allowing
parallel use of the userspace API (which is protected with ->devlock).
But hid_add_device() can fail. Currently, that is handled by immediately
destroying the associated HID device, without using ->devlock - but if
there are concurrent requests from userspace, that's wrong and leads to
NULL dereferences and/or memory corruption (via use-after-free).
Fix it by leaving the HID device as-is in the worker. We can clean it up
later, either in the UHID_DESTROY command handler or in the ->release()
handler.
Cc: stable@vger.kernel.org
Fixes: 67f8ecc550 ("HID: uhid: fix timeout when probe races with IO")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Copy Intel's "Broadcast RGB" property semantics to add manual override
of the HDMI pixel range for monitors that don't abide by the content
of the AVI Infoframe.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The datasheet for this sensor documents the minimum vblanking as being
32 lines. It does fix some problems with occasional black lines at the
bottom of images (tested on Raspberry Pi).
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
THe AON_INTR2 controller manages the HDMI interrupts, combining them
into a single interrupt passed to the GIC. bcm2711.dtsi declares the
interrupt as being IRQ_TYPE_LEVEL_HIGH, but it should be
IRQ_TYPE_EDGE_RISING. Most of the time the distinction shouldn't
matter, but there is a small possibility of losing interrupts unless
it is corrected.
See: http://lists.infradead.org/pipermail/linux-arm-kernel/2022-January/710292.html
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
commit 2aac550da3 upstream.
The recent few quirk entries for Lenovo haven't been put in the right
order. Let's arrange the table again.
Fixes: ad7cc2d41b ("ALSA: hda/realtek: Quirks to enable speaker output...")
Fixes: 6dc8697622 ("ALSA: hda/realtek: Add speaker fixup for some Yoga 15ITL5 devices")
Fixes: 8f4c90427a ("ALSA: hda/realtek: Add quirk for Legion Y9000X 2020")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c193300867 upstream.
This patch addresses an issue where after rebooting from Windows into Linux
there would be no audio output.
It turns out that the Realtek Audio driver on Windows changes some coeffs
which are not being reset/reinitialized when rebooting the machine. As a
result, there is no audio output until these coeffs are being reset to
their initial state. This patch takes care of that by setting known-good
(initial) values to the coeffs.
We initially relied upon alc1220_fixup_clevo_p950() to fix some pins in the
connection list. However, it also sets coef 0x7 which does not need to be
touched. Furthermore, to prevent mixing device-specific quirks I introduced
a new alc1220_fixup_gb_x570() which is heavily based on
alc1220_fixup_clevo_p950() but does not set coeff 0x7 and fixes the coeffs
that are actually needed instead.
This new alc1220_fixup_gb_x570() is believed to also work for other boards,
like the Gigabyte X570 Aorus Extreme and the newer Gigabyte Aorus X570S
Master. However, as there is no way for me to test these I initially only
enable this new behaviour for the mainboard I have which is the Gigabyte
X570(non-S) Aorus Master.
I tested this patch on the 5.15 branch as well as on master and it is
working well for me.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=205275
Signed-off-by: Christian Lachner <gladiac@gmail.com>
Fixes: 0d45e86d22 ("ALSA: hda/realtek - Fix silent output on Gigabyte X570 Aorus Master")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220103140517.30273-2-gladiac@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9fb12fe5b9 upstream.
The fixed counter 3 is used for the Topdown metrics, which hasn't been
enabled for KVM guests. Userspace accessing to it will fail as it's not
included in get_fixed_pmc(). This breaks KVM selftests on ICX+ machines,
which have this counter.
To reproduce it on ICX+ machines, ./state_test reports:
==== Test Assertion Failure ====
lib/x86_64/processor.c:1078: r == nmsrs
pid=4564 tid=4564 - Argument list too long
1 0x000000000040b1b9: vcpu_save_state at processor.c:1077
2 0x0000000000402478: main at state_test.c:209 (discriminator 6)
3 0x00007fbe21ed5f92: ?? ??:0
4 0x000000000040264d: _start at ??:?
Unexpected result from KVM_GET_MSRS, r: 17 (failed MSR was 0x30c)
With this patch, it works well.
Signed-off-by: Wei Wang <wei.w.wang@intel.com>
Message-Id: <20211217124934.32893-1-wei.w.wang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Fixes: e2ada66ec4 ("kvm: x86: Add Intel PMU MSRs to msrs_to_save[]")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47a1db8e79 upstream.
An initialised kobject must be freed using kobject_put() to avoid
leaking associated resources (e.g. the object name).
Commit fe3c606843 ("firmware: Fix a reference count leak.") "fixed"
the leak in the first error path of the file registration helper but
left the second one unchanged. This "fix" would however result in a NULL
pointer dereference due to the release function also removing the never
added entry from the fw_cfg_entry_cache list. This has now been
addressed.
Fix the remaining kobject leak by restoring the common error path and
adding the missing kobject_put().
Fixes: 75f3e8e47f ("firmware: introduce sysfs driver for QEMU's fw_cfg device")
Cc: stable@vger.kernel.org # 4.6
Cc: Gabriel Somlo <somlo@cmu.edu>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211201132528.30025-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b144dedb9 upstream.
Syzbot reports the following WARNING:
[200~raw_local_irq_restore() called with IRQs enabled
WARNING: CPU: 1 PID: 1206 at kernel/locking/irqflag-debug.c:10
warn_bogus_irq_restore+0x1d/0x20 kernel/locking/irqflag-debug.c:10
Hardware initialization for the rtl8188cu can run for as long as 350 ms,
and the routine may be called with interrupts disabled. To avoid locking
the machine for this long, the current routine saves the interrupt flags
and enables local interrupts. The problem is that it restores the flags
at the end without disabling local interrupts first.
This patch fixes commit a53268be0c ("rtlwifi: rtl8192cu: Fix too long
disable of IRQs").
Reported-by: syzbot+cce1ee31614c171f5595@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org
Fixes: a53268be0c ("rtlwifi: rtl8192cu: Fix too long disable of IRQs")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211215171105.20623-1-Larry.Finger@lwfinger.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8aa637bf6d upstream.
Add the missing bulk-endpoint max-packet sanity check to
uvc_video_start_transfer() to avoid division by zero in
uvc_alloc_urb_buffers() in case a malicious device has broken
descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4f ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: c0efd23292 ("V4L/DVB (8145a): USB Video Class driver")
Cc: stable@vger.kernel.org # 2.6.26
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0499f419b7 upstream.
The vga16fb framebuffer driver only supports Enhanced Graphics Adapter
(EGA) and Video Graphics Array (VGA) 16 color graphic cards.
But it doesn't check if the adapter is one of those or if a VGA16 mode
is used. This means that the driver will be probed even if a VESA BIOS
Extensions (VBE) or Graphics Output Protocol (GOP) interface is used.
This issue has been present for a long time but it was only exposed by
commit d391c58271 ("drivers/firmware: move x86 Generic System
Framebuffers support") since the platform device registration to match
the {vesa,efi}fb drivers is done later as a consequence of that change.
All non-x86 architectures though treat orig_video_isVGA as a boolean so
only do the supported video mode check for x86 and not for other arches.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215001
Fixes: d391c58271 ("drivers/firmware: move x86 Generic System Framebuffers support")
Reported-by: Kris Karas <bugs-a21@moonlit-rail.com>
Cc: <stable@vger.kernel.org> # 5.15.x
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Kris Karas <bugs-a21@moonlit-rail.com>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220110095625.278836-3-javierm@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 812de04661 upstream.
With KVM_CAP_S390_USER_SIGP, there are only five Signal Processor
orders (CONDITIONAL EMERGENCY SIGNAL, EMERGENCY SIGNAL, EXTERNAL CALL,
SENSE, and SENSE RUNNING STATUS) which are intended for frequent use
and thus are processed in-kernel. The remainder are sent to userspace
with the KVM_CAP_S390_USER_SIGP capability. Of those, three orders
(RESTART, STOP, and STOP AND STORE STATUS) have the potential to
inject work back into the kernel, and thus are asynchronous.
Let's look for those pending IRQs when processing one of the in-kernel
SIGP orders, and return BUSY (CC2) if one is in process. This is in
agreement with the Principles of Operation, which states that only one
order can be "active" on a CPU at a time.
Cc: stable@vger.kernel.org
Suggested-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Eric Farman <farman@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/20211213210550.856213-2-farman@linux.ibm.com
[borntraeger@linux.ibm.com: add stable tag]
Signed-off-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff083a2d97 upstream.
Protect perf_guest_cbs with RCU to fix multiple possible errors. Luckily,
all paths that read perf_guest_cbs already require RCU protection, e.g. to
protect the callback chains, so only the direct perf_guest_cbs touchpoints
need to be modified.
Bug #1 is a simple lack of WRITE_ONCE/READ_ONCE behavior to ensure
perf_guest_cbs isn't reloaded between a !NULL check and a dereference.
Fixed via the READ_ONCE() in rcu_dereference().
Bug #2 is that on weakly-ordered architectures, updates to the callbacks
themselves are not guaranteed to be visible before the pointer is made
visible to readers. Fixed by the smp_store_release() in
rcu_assign_pointer() when the new pointer is non-NULL.
Bug #3 is that, because the callbacks are global, it's possible for
readers to run in parallel with an unregisters, and thus a module
implementing the callbacks can be unloaded while readers are in flight,
resulting in a use-after-free. Fixed by a synchronize_rcu() call when
unregistering callbacks.
Bug #1 escaped notice because it's extremely unlikely a compiler will
reload perf_guest_cbs in this sequence. perf_guest_cbs does get reloaded
for future derefs, e.g. for ->is_user_mode(), but the ->is_in_guest()
guard all but guarantees the consumer will win the race, e.g. to nullify
perf_guest_cbs, KVM has to completely exit the guest and teardown down
all VMs before KVM start its module unload / unregister sequence. This
also makes it all but impossible to encounter bug #3.
Bug #2 has not been a problem because all architectures that register
callbacks are strongly ordered and/or have a static set of callbacks.
But with help, unloading kvm_intel can trigger bug #1 e.g. wrapping
perf_guest_cbs with READ_ONCE in perf_misc_flags() while spamming
kvm_intel module load/unload leads to:
BUG: kernel NULL pointer dereference, address: 0000000000000000
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP
CPU: 6 PID: 1825 Comm: stress Not tainted 5.14.0-rc2+ #459
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
RIP: 0010:perf_misc_flags+0x1c/0x70
Call Trace:
perf_prepare_sample+0x53/0x6b0
perf_event_output_forward+0x67/0x160
__perf_event_overflow+0x52/0xf0
handle_pmi_common+0x207/0x300
intel_pmu_handle_irq+0xcf/0x410
perf_event_nmi_handler+0x28/0x50
nmi_handle+0xc7/0x260
default_do_nmi+0x6b/0x170
exc_nmi+0x103/0x130
asm_exc_nmi+0x76/0xbf
Fixes: 39447b386c ("perf: Enhance perf to allow for guest statistic collection from host")
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211111020738.2512932-2-seanjc@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40a74870b2 upstream.
'buffer_index_array' really looks like a bitmap. So it should be allocated
as such.
When kzalloc is called, a number of bytes is expected, but a number of
longs is passed instead.
In get(), if not enough memory is allocated, un-allocated memory may be
read or written.
So use bitmap_zalloc() to safely allocate the correct memory size and
avoid un-expected behavior.
While at it, change the corresponding kfree() into bitmap_free() to keep
the semantic.
Fixes: ea2c9c9f65 ("orangefs: bufmap rewrite")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6097180d8 upstream.
Prior to Linux v5.4 devtmpfs used mount_single() which treats the given
mount options as "remount" options, so it updates the configuration of
the single super_block on each mount.
Since that was changed, the mount options used for devtmpfs are ignored.
This is a regression which affect systemd - which mounts devtmpfs with
"-o mode=755,size=4m,nr_inodes=1m".
This patch restores the "remount" effect by calling reconfigure_single()
Fixes: d401727ea0 ("devtmpfs: don't mix {ramfs,shmem}_fill_super() with mount_single()")
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f634ca650f upstream.
Normally, invocations of $(HOSTCC) include $(KBUILD_HOSTLDFLAGS), which
in turn includes $(HOSTLDFLAGS), which allows users to pass in their own
flags when linking. However, the 'has_libelf' test does not, meaning
that if a user requests a specific linker via HOSTLDFLAGS=-fuse-ld=...,
it is not respected and the build might error.
For example, if a user building with clang wants to use all of the LLVM
tools without any GNU tools, they might remove all of the GNU tools from
their system or PATH then build with
$ make HOSTLDFLAGS=-fuse-ld=lld LLVM=1 LLVM_IAS=1
which says use all of the LLVM tools, the integrated assembler, and
ld.lld for linking host executables. Without this change, the build will
error because $(HOSTCC) uses its default linker, rather than the one
requested via -fuse-ld=..., which is GNU ld in clang's case in a default
configuration.
error: Cannot generate ORC metadata for CONFIG_UNWINDER_ORC=y, please
install libelf-dev, libelf-devel or elfutils-libelf-devel
make[1]: *** [Makefile:1260: prepare-objtool] Error 1
Add $(KBUILD_HOSTLDFLAGS) to the 'has_libelf' test so that the linker
choice is respected.
Link: https://github.com/ClangBuiltLinux/linux/issues/479
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Cc: Paul Barker <paul.barker@sancloud.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On a Pi3 B/B+ platform the imx219 sensor frequently generates a single corrupt
frame when the sensor first starts. This can either be a missing line, or
invalid samples within the line. This only occurrs using the Unicam kernel
driver.
Disabling trigger mode elimiates this corruption. Since trigger mode is a
legacy feature copied from the firmware driver and not expected to be needed,
remove it. Tested on the Raspberry Pi cameras and shows no ill effects.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Neither the CM4 module nor the CM4IO board have a VL805 USB3
controller. The existing "usb@0,0" node is a hangover from the
Pi 4 dts; delete it. An up-to-date firmware will automatically load
the vl805 overlay on CM4s with VL805=1 in the EEPROM config, ensuring
that the firmware is notified of any PCIe reset.
See: https://forums.raspberrypi.com/viewtopic.php?t=326088
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
commit 2e70570656 upstream.
A new warning in clang points out a place in this file where a bitwise
OR is being used with boolean types:
drivers/gpu/drm/i915/intel_pm.c:3066:12: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
changed = ilk_increase_wm_latency(dev_priv, dev_priv->wm.pri_latency, 12) |
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
This construct is intentional, as it allows every one of the calls to
ilk_increase_wm_latency() to occur (instead of short circuiting with
logical OR) while still caring about the result of each call.
To make this clearer to the compiler, use the '|=' operator to assign
the result of each ilk_increase_wm_latency() call to changed, which
keeps the meaning of the code the same but makes it obvious that every
one of these calls is expected to happen.
Link: https://github.com/ClangBuiltLinux/linux/issues/1473
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Suggested-by: Dávid Bolvanský <david.bolvansky@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211014211916.3550122-1-nathan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 502408a61f upstream.
A new warning in clang points out a place in this file where a bitwise
OR is being used with boolean expressions:
In file included from drivers/staging/wlan-ng/prism2usb.c:2:
drivers/staging/wlan-ng/hfa384x_usb.c:3787:7: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
((test_and_clear_bit(THROTTLE_RX, &hw->usb_flags) &&
~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/staging/wlan-ng/hfa384x_usb.c:3787:7: note: cast one or both operands to int to silence this warning
1 warning generated.
The comment explains that short circuiting here is undesirable, as the
calls to test_and_{clear,set}_bit() need to happen for both sides of the
expression.
Clang's suggestion would work to silence the warning but the readability
of the expression would suffer even more. To clean up the warning and
make the block more readable, use a variable for each side of the
bitwise expression.
Link: https://github.com/ClangBuiltLinux/linux/issues/1478
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20211014215703.3705371-1-nathan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7e67b8e80 upstream.
Currently, if CONFIG_RANDOM_TRUST_BOOTLOADER is enabled, multiple calls
to add_bootloader_randomness() are broken and can cause a NULL pointer
dereference, as noted by Ivan T. Ivanov. This is not only a hypothetical
problem, as qemu on arm64 may provide bootloader entropy via EFI and via
devicetree.
On the first call to add_hwgenerator_randomness(), crng_fast_load() is
executed, and if the seed is long enough, crng_init will be set to 1.
On subsequent calls to add_bootloader_randomness() and then to
add_hwgenerator_randomness(), crng_fast_load() will be skipped. Instead,
wait_event_interruptible() and then credit_entropy_bits() will be called.
If the entropy count for that second seed is large enough, that proceeds
to crng_reseed().
However, both wait_event_interruptible() and crng_reseed() depends
(at least in numa_crng_init()) on workqueues. Therefore, test whether
system_wq is already initialized, which is a sufficient indicator that
workqueue_init_early() has progressed far enough.
If we wind up hitting the !system_wq case, we later want to do what
would have been done there when wqs are up, so set a flag, and do that
work later from the rand_initialize() call.
Reported-by: Ivan T. Ivanov <iivanov@suse.de>
Fixes: 18b915ac6b ("efi/random: Treat EFI_RNG_PROTOCOL output as bootloader randomness")
Cc: stable@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
[Jason: added crng_need_done state and related logic.]
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 009ba8568b upstream.
_extract_crng() does plain loads of crng->init_time and
crng_global_init_time, which causes undefined behavior if
crng_reseed() and RNDRESEEDCRNG modify these corrently.
Use READ_ONCE() and WRITE_ONCE() to make the behavior defined.
Don't fix the race on crng->init_time by protecting it with crng->lock,
since it's not a problem for duplicate reseedings to occur. I.e., the
lockless access with READ_ONCE() is fine.
Fixes: d848e5f8e1 ("random: add new ioctl RNDRESEEDCRNG")
Fixes: e192be9d9a ("random: replace non-blocking pool with a Chacha20-based CRNG")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d73d1e320 upstream.
extract_crng() and crng_backtrack_protect() load crng_node_pool with a
plain load, which causes undefined behavior if do_numa_crng_init()
modifies it concurrently.
Fix this by using READ_ONCE(). Note: as per the previous discussion
https://lore.kernel.org/lkml/20211219025139.31085-1-ebiggers@kernel.org/T/#u,
READ_ONCE() is believed to be sufficient here, and it was requested that
it be used here instead of smp_load_acquire().
Also change do_numa_crng_init() to set crng_node_pool using
cmpxchg_release() instead of mb() + cmpxchg(), as the former is
sufficient here but is more lightweight.
Fixes: 1e7f583af6 ("random: make /dev/urandom scalable for silly userspace programs")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a8737ff06 upstream.
The received data contains the channel the received data is associated
with. If the channel number is bigger than the actual number of
channels assume broken or malicious USB device and shut it down.
This fixes the error found by clang:
| drivers/net/can/usb/gs_usb.c:386:6: error: variable 'dev' is used
| uninitialized whenever 'if' condition is true
| if (hf->channel >= GS_MAX_INTF)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
| drivers/net/can/usb/gs_usb.c:474:10: note: uninitialized use occurs here
| hf, dev->gs_hf_size, gs_usb_receive_bulk_callback,
| ^~~
Link: https://lore.kernel.org/all/20211210091158.408326-1-mkl@pengutronix.de
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c9e143084d upstream.
The runtime PM callback may be called as soon as the runtime PM facility
is enabled and activated. It means that ->suspend() may be called before
we finish probing the device in the ACPI case. Hence, NULL pointer
dereference:
intel-lpss INT34BA:00: IRQ index 0 not found
BUG: kernel NULL pointer dereference, address: 0000000000000030
...
Workqueue: pm pm_runtime_work
RIP: 0010:intel_lpss_suspend+0xb/0x40 [intel_lpss]
To fix this, first try to register the device and only after that enable
runtime PM facility.
Fixes: 4b45efe852 ("mfd: Add support for Intel Sunrisepoint LPSS devices")
Reported-by: Orlando Chamberlain <redecorating@protonmail.com>
Reported-by: Aditya Garg <gargaditya08@live.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Aditya Garg <gargaditya08@live.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211101190008.86473-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 710ad98c36 upstream.
Laurent reported that they have seen a significant amount of TCP retransmissions
at high throughput from applications residing in network namespaces talking to
the outside world via veths. The drops were seen on the qdisc layer (fq_codel,
as per systemd default) of the phys device such as ena or virtio_net due to all
traffic hitting a _single_ TX queue _despite_ multi-queue device. (Note that the
setup was _not_ using XDP on veths as the issue is generic.)
More specifically, after edbea92202 ("veth: Store queue_mapping independently
of XDP prog presence") which made it all the way back to v4.19.184+,
skb_record_rx_queue() would set skb->queue_mapping to 1 (given 1 RX and 1 TX
queue by default for veths) instead of leaving at 0.
This is eventually retained and callbacks like ena_select_queue() will also pick
single queue via netdev_core_pick_tx()'s ndo_select_queue() once all the traffic
is forwarded to that device via upper stack or other means. Similarly, for others
not implementing ndo_select_queue() if XPS is disabled, netdev_pick_tx() might
call into the skb_tx_hash() and check for prior skb_rx_queue_recorded() as well.
In general, it is a _bad_ idea for virtual devices like veth to mess around with
queue selection [by default]. Given dev->real_num_tx_queues is by default 1,
the skb->queue_mapping was left untouched, and so prior to edbea92202 the
netdev_core_pick_tx() could do its job upon __dev_queue_xmit() on the phys device.
Unbreak this and restore prior behavior by removing the skb_record_rx_queue()
from veth_xmit() altogether.
If the veth peer has an XDP program attached, then it would return the first RX
queue index in xdp_md->rx_queue_index (unless configured in non-default manner).
However, this is still better than breaking the generic case.
Fixes: edbea92202 ("veth: Store queue_mapping independently of XDP prog presence")
Fixes: 638264dc90 ("veth: Support per queue XDP ring")
Reported-by: Laurent Bernaille <laurent.bernaille@datadoghq.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Cc: Toshiaki Makita <toshiaki.makita1@gmail.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Toshiaki Makita <toshiaki.makita1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a658c929de upstream.
If cfg80211 is providing extraie's for a scanning process then ath11k will
copy that over to the firmware. The extraie.len is a 32 bit value in struct
element_info and describes the amount of bytes for the vendor information
elements.
The WMI_TLV packet is having a special WMI_TAG_ARRAY_BYTE section. This
section can have a (payload) length up to 65535 bytes because the
WMI_TLV_LEN can store up to 16 bits. The code was missing such a check and
could have created a scan request which cannot be parsed correctly by the
firmware.
But the bigger problem was the allocation of the buffer. It has to align
the TLV sections by 4 bytes. But the code was using an u8 to store the
newly calculated length of this section (with alignment). And the new
calculated length was then used to allocate the skbuff. But the actual code
to copy in the data is using the extraie.len and not the calculated
"aligned" length.
The length of extraie with IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS enabled
was 264 bytes during tests with a QCA Milan card. But it only allocated 8
bytes (264 bytes % 256) for it. As consequence, the code to memcpy the
extraie into the skb was then just overwriting data after skb->end. Things
like shinfo were therefore corrupted. This could usually be seen by a crash
in skb_zcopy_clear which tried to call a ubuf_info callback (using a bogus
address).
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-02892.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Cc: stable@vger.kernel.org
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211207142913.1734635-1-sven@narfation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d7d4c0793 upstream.
When the USB core code for getting root-hub status reports was
originally written, it was assumed that the hub driver would be its
only caller. But this isn't true now; user programs can use usbfs to
communicate with root hubs and get status reports. When they do this,
they may use a transfer_buffer that is smaller than the data returned
by the HCD, which will lead to a buffer overflow error when
usb_hcd_poll_rh_status() tries to store the status data. This was
discovered by syzbot:
BUG: KASAN: slab-out-of-bounds in memcpy include/linux/fortify-string.h:225 [inline]
BUG: KASAN: slab-out-of-bounds in usb_hcd_poll_rh_status+0x5f4/0x780 drivers/usb/core/hcd.c:776
Write of size 2 at addr ffff88801da403c0 by task syz-executor133/4062
This patch fixes the bug by reducing the amount of status data if it
won't fit in the transfer_buffer. If some data gets discarded then
the URB's completion status is set to -EOVERFLOW rather than 0, to let
the user know what happened.
Reported-and-tested-by: syzbot+3ae6a2b06f131ab9849f@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Yc+3UIQJ2STbxNua@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f663729bb upstream.
Bugzilla #213839 reports a 7-port hub that doesn't work properly when
devices are plugged into some of the ports; the kernel goes into an
unending disconnect/reinitialize loop as shown in the bug report.
This "7-port hub" comprises two four-port hubs with one plugged into
the other; the failures occur when a device is plugged into one of the
downstream hub's ports. (These hubs have other problems too. For
example, they bill themselves as USB-2.0 compliant but they only run
at full speed.)
It turns out that the failures are caused by bugs in both the kernel
and the hub. The hub's bug is that it reports a different
bmAttributes value in its configuration descriptor following a remote
wakeup (0xe0 before, 0xc0 after -- the wakeup-support bit has
changed).
The kernel's bug is inside the hub driver's resume handler. When
hub_activate() sees that one of the hub's downstream ports got a
wakeup request from a child device, it notes this fact by setting the
corresponding bit in the hub->change_bits variable. But this variable
is meant for connection changes, not wakeup events; setting it causes
the driver to believe the downstream port has been disconnected and
then connected again (in addition to having received a wakeup
request).
Because of this, the hub driver then tries to check whether the device
currently plugged into the downstream port is the same as the device
that had been attached there before. Normally this check succeeds and
wakeup handling continues with no harm done (which is why the bug
remained undetected until now). But with these dodgy hubs, the check
fails because the config descriptor has changed. This causes the hub
driver to reinitialize the child device, leading to the
disconnect/reinitialize loop described in the bug report.
The proper way to note reception of a downstream wakeup request is
to set a bit in the hub->event_bits variable instead of
hub->change_bits. That way the hub driver will realize that something
has happened to the port but will not think the port and child device
have been disconnected. This patch makes that change.
Cc: <stable@vger.kernel.org>
Tested-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YdCw7nSfWYPKWQoD@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5e6fa7a12 upstream.
Add the missing bulk-out endpoint sanity check to probe() to avoid
division by zero in bfusb_send_frame() in case a malicious device has
broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4f ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ no upstream commit given implicitly fixed through the larger refactoring
in c25b2ae136 ]
While auditing some other code, I noticed missing checks inside the pointer
arithmetic simulation, more specifically, adjust_ptr_min_max_vals(). Several
*_OR_NULL types are not rejected whereas they are _required_ to be rejected
given the expectation is that they get promoted into a 'real' pointer type
for the success case, that is, after an explicit != NULL check.
One case which stands out and is accessible from unprivileged (iff enabled
given disabled by default) is BPF ring buffer. From crafting a PoC, the NULL
check can be bypassed through an offset, and its id marking will then lead
to promotion of mem_or_null to a mem type.
bpf_ringbuf_reserve() helper can trigger this case through passing of reserved
flags, for example.
func#0 @0
0: R1=ctx(id=0,off=0,imm=0) R10=fp0
0: (7a) *(u64 *)(r10 -8) = 0
1: R1=ctx(id=0,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm
1: (18) r1 = 0x0
3: R1_w=map_ptr(id=0,off=0,ks=0,vs=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm
3: (b7) r2 = 8
4: R1_w=map_ptr(id=0,off=0,ks=0,vs=0,imm=0) R2_w=invP8 R10=fp0 fp-8_w=mmmmmmmm
4: (b7) r3 = 0
5: R1_w=map_ptr(id=0,off=0,ks=0,vs=0,imm=0) R2_w=invP8 R3_w=invP0 R10=fp0 fp-8_w=mmmmmmmm
5: (85) call bpf_ringbuf_reserve#131
6: R0_w=mem_or_null(id=2,ref_obj_id=2,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm refs=2
6: (bf) r6 = r0
7: R0_w=mem_or_null(id=2,ref_obj_id=2,off=0,imm=0) R6_w=mem_or_null(id=2,ref_obj_id=2,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm refs=2
7: (07) r0 += 1
8: R0_w=mem_or_null(id=2,ref_obj_id=2,off=1,imm=0) R6_w=mem_or_null(id=2,ref_obj_id=2,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm refs=2
8: (15) if r0 == 0x0 goto pc+4
R0_w=mem(id=0,ref_obj_id=0,off=0,imm=0) R6_w=mem(id=0,ref_obj_id=2,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm refs=2
9: R0_w=mem(id=0,ref_obj_id=0,off=0,imm=0) R6_w=mem(id=0,ref_obj_id=2,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm refs=2
9: (62) *(u32 *)(r6 +0) = 0
R0_w=mem(id=0,ref_obj_id=0,off=0,imm=0) R6_w=mem(id=0,ref_obj_id=2,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm refs=2
10: R0_w=mem(id=0,ref_obj_id=0,off=0,imm=0) R6_w=mem(id=0,ref_obj_id=2,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm refs=2
10: (bf) r1 = r6
11: R0_w=mem(id=0,ref_obj_id=0,off=0,imm=0) R1_w=mem(id=0,ref_obj_id=2,off=0,imm=0) R6_w=mem(id=0,ref_obj_id=2,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm refs=2
11: (b7) r2 = 0
12: R0_w=mem(id=0,ref_obj_id=0,off=0,imm=0) R1_w=mem(id=0,ref_obj_id=2,off=0,imm=0) R2_w=invP0 R6_w=mem(id=0,ref_obj_id=2,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm refs=2
12: (85) call bpf_ringbuf_submit#132
13: R6=invP(id=0) R10=fp0 fp-8=mmmmmmmm
13: (b7) r0 = 0
14: R0_w=invP0 R6=invP(id=0) R10=fp0 fp-8=mmmmmmmm
14: (95) exit
from 8 to 13: safe
processed 15 insns (limit 1000000) max_states_per_insn 0 total_states 1 peak_states 1 mark_read 0
OK
All three commits, that is b121b341e5 ("bpf: Add PTR_TO_BTF_ID_OR_NULL support"),
457f44363a ("bpf: Implement BPF ring buffer and verifier support for it"), and the
afbf21dce6 ("bpf: Support readonly/readwrite buffers in verifier") suffer the same
cause and their *_OR_NULL type pendants must be rejected in adjust_ptr_min_max_vals().
Make the test more robust by reusing reg_type_may_be_null() helper such that we catch
all *_OR_NULL types we have today and in future.
Note that pointer arithmetic on PTR_TO_BTF_ID, PTR_TO_RDONLY_BUF, and PTR_TO_RDWR_BUF
is generally allowed.
Fixes: b121b341e5 ("bpf: Add PTR_TO_BTF_ID_OR_NULL support")
Fixes: 457f44363a ("bpf: Implement BPF ring buffer and verifier support for it")
Fixes: afbf21dce6 ("bpf: Support readonly/readwrite buffers in verifier")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07edfece8b upstream.
At CPU-hotplug time, unbind_worker() may preempt a worker while it is
waking up. In that case the following scenario can happen:
unbind_workers() wq_worker_running()
-------------- -------------------
if (!(worker->flags & WORKER_NOT_RUNNING))
//PREEMPTED by unbind_workers
worker->flags |= WORKER_UNBOUND;
[...]
atomic_set(&pool->nr_running, 0);
//resume to worker
atomic_inc(&worker->pool->nr_running);
After unbind_worker() resets pool->nr_running, the value is expected to
remain 0 until the pool ever gets rebound in case cpu_up() is called on
the target CPU in the future. But here the race leaves pool->nr_running
with a value of 1, triggering the following warning when the worker goes
idle:
WARNING: CPU: 3 PID: 34 at kernel/workqueue.c:1823 worker_enter_idle+0x95/0xc0
Modules linked in:
CPU: 3 PID: 34 Comm: kworker/3:0 Not tainted 5.16.0-rc1+ #34
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba527-rebuilt.opensuse.org 04/01/2014
Workqueue: 0x0 (rcu_par_gp)
RIP: 0010:worker_enter_idle+0x95/0xc0
Code: 04 85 f8 ff ff ff 39 c1 7f 09 48 8b 43 50 48 85 c0 74 1b 83 e2 04 75 99 8b 43 34 39 43 30 75 91 8b 83 00 03 00 00 85 c0 74 87 <0f> 0b 5b c3 48 8b 35 70 f1 37 01 48 8d 7b 48 48 81 c6 e0 93 0
RSP: 0000:ffff9b7680277ed0 EFLAGS: 00010086
RAX: 00000000ffffffff RBX: ffff93465eae9c00 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffff9346418a0000 RDI: ffff934641057140
RBP: ffff934641057170 R08: 0000000000000001 R09: ffff9346418a0080
R10: ffff9b768027fdf0 R11: 0000000000002400 R12: ffff93465eae9c20
R13: ffff93465eae9c20 R14: ffff93465eae9c70 R15: ffff934641057140
FS: 0000000000000000(0000) GS:ffff93465eac0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 000000001cc0c000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
worker_thread+0x89/0x3d0
? process_one_work+0x400/0x400
kthread+0x162/0x190
? set_kthread_struct+0x40/0x40
ret_from_fork+0x22/0x30
</TASK>
Also due to this incorrect "nr_running == 1", further queued work may
end up not being served, because no worker is awaken at work insert time.
This raises rcutorture writer stalls for example.
Fix this with disabling preemption in the right place in
wq_worker_running().
It's worth noting that if the worker migrates and runs concurrently with
unbind_workers(), it is guaranteed to see the WORKER_UNBOUND flag update
due to set_cpus_allowed_ptr() acquiring/releasing rq->lock.
Fixes: 6d25be5782 ("sched/core, workqueues: Distangle worker accounting from rq lock")
Reviewed-by: Lai Jiangshan <jiangshanlai@gmail.com>
Tested-by: Paul E. McKenney <paulmck@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Daniel Bristot de Oliveira <bristot@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move from only supporting the default of pre-multiplied
alpha to supporting user specified blend mode using the
standardised property.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
We are using mode->crt_clock here which is filled by drm_mode_set_crtcinfo()
which is called right after .mode_valid.
Use mode->clock which is valid here.
Fixes: 624d93a4f0 ("drm/vc4: hdmi: Move clock calculation into its own function")
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Still under investigation, but the conditions under which the HVS
will accept values written to the gamma PWL are not straightforward.
Disable gamma on HVS5 again until it can be resolved to avoid
gamma being enabled with an incorrect table.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Replace the cfi directives with the UNWIND equivalents. This prevents
the .eh_frame section from being created, eliminating the warnings.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
With the automatic VL805 support being removed from the standard
CM4 dtb (since most CM4 carriers don't have a VL805), retain support
on those that do by creating a "vl805" overlay that restores the
deleted "usb@0,0" node.
The "vl805" overlay will be loaded automatically (after an upcoming
firmware update) on CM4 boards where the EEPROM config includes the
setting VL805=1.
See: https://forums.raspberrypi.com/viewtopic.php?t=326088
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
commit cf73ed894e upstream.
Since irq request is the last thing in the driver probe, it happens
later than the input device registration. This means that there is a
small time window where if the open method is called the driver will
attempt to enable not yet available irq.
Fix that by moving the irq request before the input device registration.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Fixes: 26822652c8 ("Input: add zinitix touchscreen driver")
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20220106072840.36851-2-nikita@trvn.ru
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8b5fdfc57c ]
As we build for mips, we meet following error. l1_init error with
multiple definition. Some architecture devices usually marked with
l1, l2, lxx as the start-up phase. so we change the mISDN function
names, align with Isdnl2_xxx.
mips-linux-gnu-ld: drivers/isdn/mISDN/layer1.o: in function `l1_init':
(.text+0x890): multiple definition of `l1_init'; \
arch/mips/kernel/bmips_5xxx_init.o:(.text+0xf0): first defined here
make[1]: *** [home/mips/kernel-build/linux/Makefile:1161: vmlinux] Error 1
Signed-off-by: wolfgang huang <huangjinhui@kylinos.cn>
Reported-by: k2ci <kernel-bot@kylinos.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1833c3964 ]
The "__ip6_tnl_parm" struct was left uninitialized causing an invalid
load of random data when the "__ip6_tnl_parm" struct was used elsewhere.
As an example, in the function "ip6_tnl_xmit_ctl()", it tries to access
the "collect_md" member. With "__ip6_tnl_parm" being uninitialized and
containing random data, the UBSAN detected that "collect_md" held a
non-boolean value.
The UBSAN issue is as follows:
===============================================================
UBSAN: invalid-load in net/ipv6/ip6_tunnel.c:1025:14
load of value 30 is not a valid value for type '_Bool'
CPU: 1 PID: 228 Comm: kworker/1:3 Not tainted 5.16.0-rc4+ #8
Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
Workqueue: ipv6_addrconf addrconf_dad_work
Call Trace:
<TASK>
dump_stack_lvl+0x44/0x57
ubsan_epilogue+0x5/0x40
__ubsan_handle_load_invalid_value+0x66/0x70
? __cpuhp_setup_state+0x1d3/0x210
ip6_tnl_xmit_ctl.cold.52+0x2c/0x6f [ip6_tunnel]
vti6_tnl_xmit+0x79c/0x1e96 [ip6_vti]
? lock_is_held_type+0xd9/0x130
? vti6_rcv+0x100/0x100 [ip6_vti]
? lock_is_held_type+0xd9/0x130
? rcu_read_lock_bh_held+0xc0/0xc0
? lock_acquired+0x262/0xb10
dev_hard_start_xmit+0x1e6/0x820
__dev_queue_xmit+0x2079/0x3340
? mark_lock.part.52+0xf7/0x1050
? netdev_core_pick_tx+0x290/0x290
? kvm_clock_read+0x14/0x30
? kvm_sched_clock_read+0x5/0x10
? sched_clock_cpu+0x15/0x200
? find_held_lock+0x3a/0x1c0
? lock_release+0x42f/0xc90
? lock_downgrade+0x6b0/0x6b0
? mark_held_locks+0xb7/0x120
? neigh_connected_output+0x31f/0x470
? lockdep_hardirqs_on+0x79/0x100
? neigh_connected_output+0x31f/0x470
? ip6_finish_output2+0x9b0/0x1d90
? rcu_read_lock_bh_held+0x62/0xc0
? ip6_finish_output2+0x9b0/0x1d90
ip6_finish_output2+0x9b0/0x1d90
? ip6_append_data+0x330/0x330
? ip6_mtu+0x166/0x370
? __ip6_finish_output+0x1ad/0xfb0
? nf_hook_slow+0xa6/0x170
ip6_output+0x1fb/0x710
? nf_hook.constprop.32+0x317/0x430
? ip6_finish_output+0x180/0x180
? __ip6_finish_output+0xfb0/0xfb0
? lock_is_held_type+0xd9/0x130
ndisc_send_skb+0xb33/0x1590
? __sk_mem_raise_allocated+0x11cf/0x1560
? dst_output+0x4a0/0x4a0
? ndisc_send_rs+0x432/0x610
addrconf_dad_completed+0x30c/0xbb0
? addrconf_rs_timer+0x650/0x650
? addrconf_dad_work+0x73c/0x10e0
addrconf_dad_work+0x73c/0x10e0
? addrconf_dad_completed+0xbb0/0xbb0
? rcu_read_lock_sched_held+0xaf/0xe0
? rcu_read_lock_bh_held+0xc0/0xc0
process_one_work+0x97b/0x1740
? pwq_dec_nr_in_flight+0x270/0x270
worker_thread+0x87/0xbf0
? process_one_work+0x1740/0x1740
kthread+0x3ac/0x490
? set_kthread_struct+0x100/0x100
ret_from_fork+0x22/0x30
</TASK>
===============================================================
The solution is to initialize "__ip6_tnl_parm" struct to zeros in the
"vti6_siocdevprivate()" function.
Signed-off-by: William Zhao <wizhao@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 80211be1b9 upstream.
Instead of one shot run of ADC at beginning of charging, run continuous
conversion to ensure that all charging-related values are monitored
properly (input voltage, input current, themperature etc.).
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29262e1f77 upstream.
Hytera makes a range of digital (DMR) radios. These radios can be
programmed to a allow a computer to control them over Ethernet over USB,
either using NCM or RNDIS.
This commit adds support for RNDIS for Hytera radios. I tested with a
Hytera PD785 and a Hytera MD785G. When these radios are programmed to
set up a Radio to PC Network using RNDIS, an USB interface will be added
with class 2 (Communications), subclass 2 (Abstract Modem Control) and
an interface protocol of 255 ("vendor specific" - lsusb even hints "MSFT
RNDIS?").
This patch is similar to the solution of this StackOverflow user, but
that only works for the Hytera MD785:
https://stackoverflow.com/a/53550858
To use the "Radio to PC Network" functionality of Hytera DMR radios, the
radios need to be programmed correctly in CPS (Hytera's Customer
Programming Software). "Forward to PC" should be checked in "Network"
(under "General Setting" in "Conventional") and the "USB Network
Communication Protocol" should be set to RNDIS.
Signed-off-by: Thomas Toye <thomas@toye.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 644106cdb8 upstream.
A new commit in LLVM causes an error on the use of 'long double' when
'-mno-x87' is used, which the kernel does through an alias,
'-mno-80387' (see the LLVM commit below for more details around why it
does this).
drivers/power/reset/ltc2952-poweroff.c:162:28: error: expression requires 'long double' type support, but target 'x86_64-unknown-linux-gnu' does not support it
data->wde_interval = 300L * 1E6L;
^
drivers/power/reset/ltc2952-poweroff.c:162:21: error: expression requires 'long double' type support, but target 'x86_64-unknown-linux-gnu' does not support it
data->wde_interval = 300L * 1E6L;
^
drivers/power/reset/ltc2952-poweroff.c:163:41: error: expression requires 'long double' type support, but target 'x86_64-unknown-linux-gnu' does not support it
data->trigger_delay = ktime_set(2, 500L*1E6L);
^
3 errors generated.
This happens due to the use of a 'long double' literal. The 'E6' part of
'1E6L' causes the literal to be a 'double' then the 'L' suffix promotes
it to 'long double'.
There is no visible reason for floating point values in this driver, as
the values are only assigned to integer types. Use NSEC_PER_MSEC, which
is the same integer value as '1E6L', to avoid changing functionality but
fix the error.
Fixes: 6647156c00 ("power: reset: add LTC2952 poweroff driver")
Link: https://github.com/ClangBuiltLinux/linux/issues/1497
Link: a8083d42b1
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5055dc0348 upstream.
The role of ena_calc_max_io_queue_num() is to return the number
of queues supported by the device, which means the return value
should be >=0.
The function that calls ena_calc_max_io_queue_num(), checks
the return value. If it is 0, it means the device reported
it supports 0 IO queues. This case is considered an error
and is handled by the calling function accordingly.
However the current implementation of ena_calc_max_io_queue_num()
is wrong, since when it detects the device supports 0 IO queues,
it returns -EFAULT.
In such a case the calling function doesn't detect the error,
and therefore doesn't handle it.
This commit changes ena_calc_max_io_queue_num() to return 0
in case the device reported it supports 0 queues, allowing the
calling function to properly handle the error case.
Fixes: 736ce3f414 ("net: ena: make ethtool -l show correct max number of queues")
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c255a34e02 upstream.
ena_com_tx_comp_req_id_get() checks the req_id of a received completion,
and if it is out of bounds returns -EINVAL. This is a sign that
something is wrong with the device and it needs to be reset.
The current code does not reset the device in this case, which leaves
the driver in an undefined state, where this completion is not properly
handled.
This commit adds a call to handle_invalid_req_id() in ena_clean_tx_irq()
and ena_clean_xdp_irq() which resets the device to fix the issue.
This commit also removes unnecessary request id checks from
validate_tx_req_id() and validate_xdp_req_id(). This check is unneeded
because it was already performed in ena_com_tx_comp_req_id_get(), which
is called right before these functions.
Fixes: 548c4940b9 ("net: ena: Implement XDP_TX action")
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d18a07897 upstream.
tx_queue_len can be set to ~0U, we need to be more
careful about overflows.
__fls(0) is undefined, as this report shows:
UBSAN: shift-out-of-bounds in net/sched/sch_qfq.c:1430:24
shift exponent 51770272 is too large for 32-bit type 'int'
CPU: 0 PID: 25574 Comm: syz-executor.0 Not tainted 5.16.0-rc7-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x201/0x2d8 lib/dump_stack.c:106
ubsan_epilogue lib/ubsan.c:151 [inline]
__ubsan_handle_shift_out_of_bounds+0x494/0x530 lib/ubsan.c:330
qfq_init_qdisc+0x43f/0x450 net/sched/sch_qfq.c:1430
qdisc_create+0x895/0x1430 net/sched/sch_api.c:1253
tc_modify_qdisc+0x9d9/0x1e20 net/sched/sch_api.c:1660
rtnetlink_rcv_msg+0x934/0xe60 net/core/rtnetlink.c:5571
netlink_rcv_skb+0x200/0x470 net/netlink/af_netlink.c:2496
netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
netlink_unicast+0x814/0x9f0 net/netlink/af_netlink.c:1345
netlink_sendmsg+0xaea/0xe60 net/netlink/af_netlink.c:1921
sock_sendmsg_nosec net/socket.c:704 [inline]
sock_sendmsg net/socket.c:724 [inline]
____sys_sendmsg+0x5b9/0x910 net/socket.c:2409
___sys_sendmsg net/socket.c:2463 [inline]
__sys_sendmsg+0x280/0x370 net/socket.c:2492
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
Fixes: 462dbc9101 ("pkt_sched: QFQ Plus: fair-queueing service at DRR cost")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 938f2e0b57 upstream.
The addition of routable multicast TX handling introduced a
bug/regression for packets with a link-local multicast destination:
These packets would be sent to all batman-adv nodes with a multicast
router and to all batman-adv nodes with an old version without multicast
router detection.
This even disregards the batman-adv multicast fanout setting, which can
potentially lead to an unwanted, high number of unicast transmissions or
even congestion.
Fixing this by avoiding to send link-local multicast packets to nodes in
the multicast router list.
Fixes: 11d458c1cb ("batman-adv: mcast: apply optimizations for routable packets, too")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8bda81a4d4 upstream.
lwtunnel_valid_encap_type_attr is used to validate encap attributes
within a multipath route. Add length validation checking to the type.
lwtunnel_valid_encap_type_attr is called converting attributes to
fib{6,}_config struct which means it is used before fib_get_nhs,
ip6_route_multipath_add, and ip6_route_multipath_del - other
locations that use rtnh_ok and then nla_get_u16 on RTA_ENCAP_TYPE
attribute.
Fixes: 9ed59592e3 ("lwtunnel: fix autoload of lwt modules")
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4619bcf913 upstream.
Commit referenced in the Fixes tag used nla_memcpy for RTA_GATEWAY as
does the current nla_get_in6_addr. nla_memcpy protects against accessing
memory greater than what is in the attribute, but there is no check
requiring the attribute to have an IPv6 address. Add it.
Fixes: 51ebd31815 ("ipv6: add support of equal cost multipath (ECMP)")
Signed-off-by: David Ahern <dsahern@kernel.org>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0daf5cb217 upstream.
There's another compilation fail (first here [1]) reported by kernel
test robot for W=1 clang build:
>> samples/ftrace/ftrace-direct-multi-modify.c:7:6: warning: no previous
prototype for function 'my_direct_func1' [-Wmissing-prototypes]
void my_direct_func1(unsigned long ip)
Direct functions in ftrace direct sample modules need to have prototypes
defined. They are already global in order to be visible for the inline
assembly, so there's no problem.
The kernel test robot reported just error for ftrace-direct-multi-modify,
but I got same errors also for the rest of the modules touched by this patch.
[1] 67d4f6e3bf ftrace/samples: Add missing prototype for my_direct_func
Link: https://lkml.kernel.org/r/20211219135317.212430-1-jolsa@kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Fixes: e1067a07cf ("ftrace/samples: Add module to test multi direct modify interface")
Fixes: ae0cc3b7e7 ("ftrace/samples: Add a sample module that implements modify_ftrace_direct()")
Fixes: 156473a0ff ("ftrace: Add another example of register_ftrace_direct() use case")
Fixes: b06457c83a ("ftrace: Add sample module that uses register_ftrace_direct()")
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e738451d78 upstream.
There was a wrong queues representation in sysfs during
driver's reinitialization in case of online cpus number is
less than combined queues. It was caused by stopped
NetworkManager, which is responsible for calling vsi_open
function during driver's initialization.
In specific situation (ex. 12 cpus online) there were 16 queues
in /sys/class/net/<iface>/queues. In case of modifying queues with
value higher, than number of online cpus, then it caused write
errors and other errors.
Add updating of sysfs's queues representation during driver
initialization.
Fixes: 41c445ff0f ("i40e: main driver core")
Signed-off-by: Lukasz Cieplicki <lukaszx.cieplicki@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40feded8a2 upstream.
When loading the i40e driver, it prints a message like: 'The driver for the
device detected a newer version of the NVM image v1.x than expected v1.y.
Please install the most recent version of the network driver.' This is
misleading as the driver is working as expected.
Fix that by removing the second part of message and changing it from
dev_info to dev_dbg.
Fixes: 4fb29bddb5 ("i40e: The driver now prints the API version in error message")
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68a18ad713 upstream.
Clang static analysis reports this warnings
mlme.c:5332:7: warning: Branch condition evaluates to a
garbage value
have_higher_than_11mbit)
^~~~~~~~~~~~~~~~~~~~~~~
have_higher_than_11mbit is only set to true some of the time in
ieee80211_get_rates() but is checked all of the time. So
have_higher_than_11mbit needs to be initialized to false.
Fixes: 5d6a1b069b ("mac80211: set basic rates earlier")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20211223162848.3243702-1-trix@redhat.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3087a6f36e upstream.
This code used to copy in an unsigned long worth of data before
the sockptr_t conversion, so restore that.
Fixes: a7b75c5a8c ("net: pass a sockptr_t into ->setsockopt")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b35a0f4dd5 upstream.
If dst->is_global field is not set, the GRH fields are not cleared
and the following infoleak is reported.
=====================================================
BUG: KMSAN: kernel-infoleak in instrument_copy_to_user include/linux/instrumented.h:121 [inline]
BUG: KMSAN: kernel-infoleak in _copy_to_user+0x1c9/0x270 lib/usercopy.c:33
instrument_copy_to_user include/linux/instrumented.h:121 [inline]
_copy_to_user+0x1c9/0x270 lib/usercopy.c:33
copy_to_user include/linux/uaccess.h:209 [inline]
ucma_init_qp_attr+0x8c7/0xb10 drivers/infiniband/core/ucma.c:1242
ucma_write+0x637/0x6c0 drivers/infiniband/core/ucma.c:1732
vfs_write+0x8ce/0x2030 fs/read_write.c:588
ksys_write+0x28b/0x510 fs/read_write.c:643
__do_sys_write fs/read_write.c:655 [inline]
__se_sys_write fs/read_write.c:652 [inline]
__ia32_sys_write+0xdb/0x120 fs/read_write.c:652
do_syscall_32_irqs_on arch/x86/entry/common.c:114 [inline]
__do_fast_syscall_32+0x96/0xf0 arch/x86/entry/common.c:180
do_fast_syscall_32+0x34/0x70 arch/x86/entry/common.c:205
do_SYSENTER_32+0x1b/0x20 arch/x86/entry/common.c:248
entry_SYSENTER_compat_after_hwframe+0x4d/0x5c
Local variable resp created at:
ucma_init_qp_attr+0xa4/0xb10 drivers/infiniband/core/ucma.c:1214
ucma_write+0x637/0x6c0 drivers/infiniband/core/ucma.c:1732
Bytes 40-59 of 144 are uninitialized
Memory access of size 144 starts at ffff888167523b00
Data copied to user address 0000000020000100
CPU: 1 PID: 25910 Comm: syz-executor.1 Not tainted 5.16.0-rc5-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
=====================================================
Fixes: 4ba66093bd ("IB/core: Check for global flag when using ah_attr")
Link: https://lore.kernel.org/r/0e9dd51f93410b7b2f4f5562f52befc878b71afa.1641298868.git.leonro@nvidia.com
Reported-by: syzbot+6d532fa8f9463da290bc@syzkaller.appspotmail.com
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b712941c80 upstream.
In the absence of this validation, if the user requests to
configure queues more than the enabled queues, it results in
sending the requested number of queues to the kernel stack
(due to the asynchronous nature of VF response), in which
case the stack might pick a queue to transmit that is not
enabled and result in Tx hang. Fix this bug by
limiting the total number of queues allocated for VF to
active queues of VF.
Fixes: d5b33d0244 ("i40evf: add ndo_setup_tc callback to i40evf")
Signed-off-by: Ashwin Vijayavel <ashwin.vijayavel@intel.com>
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 01cbf50877 upstream.
Hide i40e opcode information sent during response to VF in case when
untrusted VF tried to change MAC on the VF interface.
This is implemented by adding an additional parameter 'hide' to the
response sent to VF function that hides the display of error
information, but forwards the error code to VF.
Previously it was not possible to send response with some error code
to VF without displaying opcode information.
Fixes: 5c3c48ac6b ("i40e: implement virtual device interface")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Reviewed-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 754e438235 upstream.
Alexander reported a use of uninitialized value in
atusb_set_extended_addr(), that is caused by reading 0 bytes via
usb_control_msg().
Fix it by validating if the number of bytes transferred is actually
correct, since usb_control_msg() may read less bytes, than was requested
by caller.
Fail log:
BUG: KASAN: uninit-cmp in ieee802154_is_valid_extended_unicast_addr include/linux/ieee802154.h:310 [inline]
BUG: KASAN: uninit-cmp in atusb_set_extended_addr drivers/net/ieee802154/atusb.c:1000 [inline]
BUG: KASAN: uninit-cmp in atusb_probe.cold+0x29f/0x14db drivers/net/ieee802154/atusb.c:1056
Uninit value used in comparison: 311daa649a2003bd stack handle: 000000009a2003bd
ieee802154_is_valid_extended_unicast_addr include/linux/ieee802154.h:310 [inline]
atusb_set_extended_addr drivers/net/ieee802154/atusb.c:1000 [inline]
atusb_probe.cold+0x29f/0x14db drivers/net/ieee802154/atusb.c:1056
usb_probe_interface+0x314/0x7f0 drivers/usb/core/driver.c:396
Fixes: 7490b008d1 ("ieee802154: add support for atusb transceiver")
Reported-by: Alexander Potapenko <glider@google.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/20220104182806.7188-1-paskripkin@gmail.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 823e670f7e upstream.
With the new osnoise tracer, we are seeing the below splat:
Kernel attempted to read user page (c7d880000) - exploit attempt? (uid: 0)
BUG: Unable to handle kernel data access on read at 0xc7d880000
Faulting instruction address: 0xc0000000002ffa10
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Radix SMP NR_CPUS=2048 NUMA pSeries
...
NIP [c0000000002ffa10] __trace_array_vprintk.part.0+0x70/0x2f0
LR [c0000000002ff9fc] __trace_array_vprintk.part.0+0x5c/0x2f0
Call Trace:
[c0000008bdd73b80] [c0000000001c49cc] put_prev_task_fair+0x3c/0x60 (unreliable)
[c0000008bdd73be0] [c000000000301430] trace_array_printk_buf+0x70/0x90
[c0000008bdd73c00] [c0000000003178b0] trace_sched_switch_callback+0x250/0x290
[c0000008bdd73c90] [c000000000e70d60] __schedule+0x410/0x710
[c0000008bdd73d40] [c000000000e710c0] schedule+0x60/0x130
[c0000008bdd73d70] [c000000000030614] interrupt_exit_user_prepare_main+0x264/0x270
[c0000008bdd73de0] [c000000000030a70] syscall_exit_prepare+0x150/0x180
[c0000008bdd73e10] [c00000000000c174] system_call_vectored_common+0xf4/0x278
osnoise tracer on ppc64le is triggering osnoise_taint() for negative
duration in get_int_safe_duration() called from
trace_sched_switch_callback()->thread_exit().
The problem though is that the check for a valid trace_percpu_buffer is
incorrect in get_trace_buf(). The check is being done after calculating
the pointer for the current cpu, rather than on the main percpu pointer.
Fix the check to be against trace_percpu_buffer.
Link: https://lkml.kernel.org/r/a920e4272e0b0635cf20c444707cbce1b2c8973d.1640255304.git.naveen.n.rao@linux.vnet.ibm.com
Cc: stable@vger.kernel.org
Fixes: e2ace00117 ("tracing: Choose static tp_printk buffer by explicit nesting count")
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5c0042200 upstream.
As Yi Zhuang reported in bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=214299
There is potential deadlock during quota data flush as below:
Thread A: Thread B:
f2fs_dquot_acquire
down_read(&sbi->quota_sem)
f2fs_write_checkpoint
block_operations
f2fs_look_all
down_write(&sbi->cp_rwsem)
f2fs_quota_write
f2fs_write_begin
__do_map_lock
f2fs_lock_op
down_read(&sbi->cp_rwsem)
__need_flush_qutoa
down_write(&sbi->quota_sem)
This patch changes block_operations() to use trylock, if it fails,
it means there is potential quota data updater, in this condition,
let's flush quota data first and then trylock again to check dirty
status of quota data.
The side effect is: in heavy race condition (e.g. multi quota data
upaters vs quota data flusher), it may decrease the probability of
synchronizing quota data successfully in checkpoint() due to limited
retry time of quota flush.
Reported-by: Yi Zhuang <zhuangyi1@huawei.com>
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To allow for the cases where a simple panel does have a GPIO
controlled backlight. Defaults to having no backlight defined.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Use GitHubs issue form for bug reports.
- modern look
- user don't need to mess with given markdown parts while filling the issue template
Setup config.yml for general questions and problems with the Raspbian distribution packages.
The driver did allow the exposure to go up to VTS - 4 lines,
but this would produce a visible line on 1280x800, and a stall of
the sensor at 640x480.
Whilst it appears to work with a difference of 5, the datasheet states
there should be at least 25 lines difference between VTS and exposure,
so use that value.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
commit 08389d8882 upstream.
Add a kconfig knob which allows for unprivileged bpf to be disabled by default.
If set, the knob sets /proc/sys/kernel/unprivileged_bpf_disabled to value of 2.
This still allows a transition of 2 -> {0,1} through an admin. Similarly,
this also still keeps 1 -> {1} behavior intact, so that once set to permanently
disabled, it cannot be undone aside from a reboot.
We've also added extra2 with max of 2 for the procfs handler, so that an admin
still has a chance to toggle between 0 <-> 2.
Either way, as an additional alternative, applications can make use of CAP_BPF
that we added a while ago.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/74ec548079189e4e4dffaeb42b8987bb3c852eee.1620765074.git.daniel@iogearbox.net
Cc: Salvatore Bonaccorso <carnil@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e22e45fc9e upstream.
A real world panic issue was found as follow in Linux 5.4.
BUG: unable to handle page fault for address: ffffde49a863de28
PGD 7e6fe62067 P4D 7e6fe62067 PUD 7e6fe63067 PMD f51e064067 PTE 0
RIP: 0010:tw_timer_handler+0x20/0x40
Call Trace:
<IRQ>
call_timer_fn+0x2b/0x120
run_timer_softirq+0x1ef/0x450
__do_softirq+0x10d/0x2b8
irq_exit+0xc7/0xd0
smp_apic_timer_interrupt+0x68/0x120
apic_timer_interrupt+0xf/0x20
This issue was also reported since 2017 in the thread [1],
unfortunately, the issue was still can be reproduced after fixing
DCCP.
The ipv4_mib_exit_net is called before tcp_sk_exit_batch when a net
namespace is destroyed since tcp_sk_ops is registered befrore
ipv4_mib_ops, which means tcp_sk_ops is in the front of ipv4_mib_ops
in the list of pernet_list. There will be a use-after-free on
net->mib.net_statistics in tw_timer_handler after ipv4_mib_exit_net
if there are some inflight time-wait timers.
This bug is not introduced by commit f2bf415cfe ("mib: add net to
NET_ADD_STATS_BH") since the net_statistics is a global variable
instead of dynamic allocation and freeing. Actually, commit
61a7e26028 ("mib: put net statistics on struct net") introduces
the bug since it put net statistics on struct net and free it when
net namespace is destroyed.
Moving init_ipv4_mibs() to the front of tcp_init() to fix this bug
and replace pr_crit() with panic() since continuing is meaningless
when init_ipv4_mibs() fails.
[1] https://groups.google.com/g/syzkaller/c/p1tn-_Kc6l4/m/smuL_FMAAgAJ?pli=1
Fixes: 61a7e26028 ("mib: put net statistics on struct net")
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Cc: Cong Wang <cong.wang@bytedance.com>
Cc: Fam Zheng <fam.zheng@bytedance.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211228104145.9426-1-songmuchun@bytedance.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 142c779d05 upstream.
The PVSCSI implementation in the VMware hypervisor under specific
configuration ("SCSI Bus Sharing" set to "Physical") returns zero dataLen
in the completion descriptor for READ CAPACITY(16). As a result, the kernel
can not detect proper disk geometry. This can be recognized by the kernel
message:
[ 0.776588] sd 1:0:0:0: [sdb] Sector size 0 reported, assuming 512.
The PVSCSI implementation in QEMU does not set dataLen at all, keeping it
zeroed. This leads to a boot hang as was reported by Shmulik Ladkani.
It is likely that the controller returns the garbage at the end of the
buffer. Residual length should be set by the driver in that case. The SCSI
layer will erase corresponding data. See commit bdb2b8cab4 ("[SCSI] erase
invalid data returned by device") for details.
Commit e662502b3a ("scsi: vmw_pvscsi: Set correct residual data length")
introduced the issue by setting residual length unconditionally, causing
the SCSI layer to erase the useful payload beyond dataLen when this value
is returned as 0.
As a result, considering existing issues in implementations of PVSCSI
controllers, we do not want to call scsi_set_resid() when dataLen ==
0. Calling scsi_set_resid() has no effect if dataLen equals buffer length.
Link: https://lore.kernel.org/lkml/20210824120028.30d9c071@blondie/
Link: https://lore.kernel.org/r/20211220190514.55935-1-amakhalov@vmware.com
Fixes: e662502b3a ("scsi: vmw_pvscsi: Set correct residual data length")
Cc: Matt Wang <wwentao@vmware.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Vishal Bhakta <vbhakta@vmware.com>
Cc: VMware PV-Drivers <pv-drivers@vmware.com>
Cc: James E.J. Bottomley <jejb@linux.ibm.com>
Cc: linux-scsi@vger.kernel.org
Cc: stable@vger.kernel.org
Reported-and-suggested-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Alexey Makhalov <amakhalov@vmware.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cfd0d84ba2 upstream.
In 4.13, commit 74310e06be ("android: binder: Move buffer out of area shared with user space")
fixed a kernel structure visibility issue. As part of that patch,
sizeof(void *) was used as the buffer size for 0-length data payloads so
the driver could detect abusive clients sending 0-length asynchronous
transactions to a server by enforcing limits on async_free_size.
Unfortunately, on the "free" side, the accounting of async_free_space
did not add the sizeof(void *) back. The result was that up to 8-bytes of
async_free_space were leaked on every async transaction of 8-bytes or
less. These small transactions are uncommon, so this accounting issue
has gone undetected for several years.
The fix is to use "buffer_size" (the allocated buffer size) instead of
"size" (the logical buffer size) when updating the async_free_space
during the free operation. These are the same except for this
corner case of asynchronous transactions with payloads < 8 bytes.
Fixes: 74310e06be ("android: binder: Move buffer out of area shared with user space")
Signed-off-by: Todd Kjos <tkjos@google.com>
Cc: stable@vger.kernel.org # 4.14+
Link: https://lore.kernel.org/r/20211220190150.2107077-1-tkjos@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e484409258 upstream.
The Fresco Logic FL1100 controller needs the TRUST_TX_LENGTH quirk like
other Fresco controllers, but should not have the BROKEN_MSI quirks set.
BROKEN_MSI quirk causes issues in detecting usb drives connected to docks
with this FL1100 controller.
The BROKEN_MSI flag was apparently accidentally set together with the
TRUST_TX_LENGTH quirk
Original patch went to stable so this should go there as well.
Fixes: ea0f69d821 ("xhci: Enable trust tx length quirk for Fresco FL11 USB controller")
Cc: stable@vger.kernel.org
cc: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211221112825.54690-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7865173cf upstream.
Play a video on the raven (or PCO, raven2) platform, and then do the S3
test. When resume, the following error will be reported:
amdgpu 0000:02:00.0: [drm:amdgpu_ring_test_helper [amdgpu]] *ERROR* ring
vcn_dec test failed (-110)
[drm:amdgpu_device_ip_resume_phase2 [amdgpu]] *ERROR* resume of IP block
<vcn_v1_0> failed -110
amdgpu 0000:02:00.0: amdgpu: amdgpu_device_ip_resume failed (-110).
PM: dpm_run_callback(): pci_pm_resume+0x0/0x90 returns -110
[why]
When playing the video: The power state flag of the vcn block is set to
POWER_STATE_ON.
When doing suspend: There is no change to the power state flag of the
vcn block, it is still POWER_STATE_ON.
When doing resume: Need to open the power gate of the vcn block and set
the power state flag of the VCN block to POWER_STATE_ON.
But at this time, the power state flag of the vcn block is already
POWER_STATE_ON. The power status flag check in the "8f2cdef drm/amd/pm:
avoid duplicate powergate/ungate setting" patch will return the
amdgpu_dpm_set_powergating_by_smu function directly.
As a result, the gate of the power was not opened, causing the
subsequent ring test to fail.
[how]
In the suspend function of the vcn block, explicitly change the power
state flag of the vcn block to POWER_STATE_OFF.
BugLink: https://gitlab.freedesktop.org/drm/amd/-/issues/1828
Signed-off-by: chen gong <curry.gong@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7175f02c4e upstream.
Replace sa_family_t with __kernel_sa_family_t to fix the following
linux/nfc.h userspace compilation errors:
/usr/include/linux/nfc.h:266:2: error: unknown type name 'sa_family_t'
sa_family_t sa_family;
/usr/include/linux/nfc.h:274:2: error: unknown type name 'sa_family_t'
sa_family_t sa_family;
Fixes: 23b7869c0f ("NFC: add the NFC socket raw protocol")
Fixes: d646960f79 ("NFC: Initial LLCP support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 79b69a8370 upstream.
Fix user-space builds if it includes /usr/include/linux/nfc.h before
some of other headers:
/usr/include/linux/nfc.h:281:9: error: unknown type name ‘size_t’
281 | size_t service_name_len;
| ^~~~~~
Fixes: d646960f79 ("NFC: Initial LLCP support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bb436283e2 ]
Wrong user data may cause warning in i2c_transfer(), ex: zero msgs.
Userspace should not be able to trigger warnings, so this patch adds
validation checks for user data in compact ioctl to prevent reported
warnings
Reported-and-tested-by: syzbot+e417648b303855b91d8a@syzkaller.appspotmail.com
Fixes: 7d5cb45655 ("i2c compat ioctls: move to ->compat_ioctl()")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf2b09fedc ]
The reference taken by 'of_find_device_by_node()' must be released when
not needed anymore.
Add the corresponding 'put_device()' in the and error handling paths.
Fixes: 18a6c85fcc ("fsl/fman: Add FMan Port Support")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92a34ab169 ]
As we can see from the comment of the nla_put() that it could return
-EMSGSIZE if the tailroom of the skb is insufficient.
Therefore, it should be better to check the return value of the
nla_put_u32 and return the error code if error accurs.
Also, there are many other functions have the same problem, and if this
patch is correct, I will commit a new version to fix all.
Fixes: 955dc68cb9 ("net/ncsi: Add generic netlink family")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20211229032118.1706294-1-jiasheng@iscas.ac.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c1952aeaa ]
udpgso_bench_tx call setup_sockaddr() for dest address before
parsing all arguments, if we specify "-p ${dst_port}" after "-D ${dst_ip}",
then ${dst_port} will be ignored, and using default cfg_port 8000.
This will cause test case "multiple GRO socks" failed in udpgro.sh.
Setup sockaddr after parsing all arguments.
Fixes: 3a687bef14 ("selftests: udp gso benchmark")
Signed-off-by: Jianguo Wu <wujianguo@chinatelecom.cn>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/ff620d9f-5b52-06ab-5286-44b945453002@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 992d8a4e38 ]
In case of an error in mlx5e_set_features(), 'netdev->features' must be
updated with the correct state of the device to indicate which features
were updated successfully.
To do that we maintain a copy of 'netdev->features' and update it after
successful feature changes, so we can assign it to back to
'netdev->features' if needed.
However, since not all netdev features are handled by the driver (e.g.
GRO/TSO/etc), some features may not be updated correctly in case of an
error updating another feature.
For example, while requesting to disable TSO (feature which is not
handled by the driver) and enable HW-GRO, if an error occurs during
HW-GRO enable, 'oper_features' will be assigned with 'netdev->features'
and HW-GRO turned off. TSO will remain enabled in such case, which is a
bug.
To solve that, instead of using 'netdev->features' as the baseline of
'oper_features' and changing it on set feature success, use 'features'
instead and update it in case of errors.
Fixes: 75b81ce719 ("net/mlx5e: Don't override netdev features field unless in error flow")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 349d43127d ]
A crash occurs when smc_cdc_tx_handler() tries to access smc_sock
but smc_release() has already freed it.
[ 4570.695099] BUG: unable to handle page fault for address: 000000002eae9e88
[ 4570.696048] #PF: supervisor write access in kernel mode
[ 4570.696728] #PF: error_code(0x0002) - not-present page
[ 4570.697401] PGD 0 P4D 0
[ 4570.697716] Oops: 0002 [#1] PREEMPT SMP NOPTI
[ 4570.698228] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.16.0-rc4+ #111
[ 4570.699013] Hardware name: Alibaba Cloud Alibaba Cloud ECS, BIOS 8c24b4c 04/0
[ 4570.699933] RIP: 0010:_raw_spin_lock+0x1a/0x30
<...>
[ 4570.711446] Call Trace:
[ 4570.711746] <IRQ>
[ 4570.711992] smc_cdc_tx_handler+0x41/0xc0
[ 4570.712470] smc_wr_tx_tasklet_fn+0x213/0x560
[ 4570.712981] ? smc_cdc_tx_dismisser+0x10/0x10
[ 4570.713489] tasklet_action_common.isra.17+0x66/0x140
[ 4570.714083] __do_softirq+0x123/0x2f4
[ 4570.714521] irq_exit_rcu+0xc4/0xf0
[ 4570.714934] common_interrupt+0xba/0xe0
Though smc_cdc_tx_handler() checked the existence of smc connection,
smc_release() may have already dismissed and released the smc socket
before smc_cdc_tx_handler() further visits it.
smc_cdc_tx_handler() |smc_release()
if (!conn) |
|
|smc_cdc_tx_dismiss_slots()
| smc_cdc_tx_dismisser()
|
|sock_put(&smc->sk) <- last sock_put,
| smc_sock freed
bh_lock_sock(&smc->sk) (panic) |
To make sure we won't receive any CDC messages after we free the
smc_sock, add a refcount on the smc_connection for inflight CDC
message(posted to the QP but haven't received related CQE), and
don't release the smc_connection until all the inflight CDC messages
haven been done, for both success or failed ones.
Using refcount on CDC messages brings another problem: when the link
is going to be destroyed, smcr_link_clear() will reset the QP, which
then remove all the pending CQEs related to the QP in the CQ. To make
sure all the CQEs will always come back so the refcount on the
smc_connection can always reach 0, smc_ib_modify_qp_reset() was replaced
by smc_ib_modify_qp_error().
And remove the timeout in smc_wr_tx_wait_no_pending_sends() since we
need to wait for all pending WQEs done, or we may encounter use-after-
free when handling CQEs.
For IB device removal routine, we need to wait for all the QPs on that
device been destroyed before we can destroy CQs on the device, or
the refcount on smc_connection won't reach 0 and smc_sock cannot be
released.
Fixes: 5f08318f61 ("smc: connection data control (CDC)")
Reported-by: Wen Gu <guwen@linux.alibaba.com>
Signed-off-by: Dust Li <dust.li@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90cee52f2e ]
We found smc_llc_send_link_delete_all() sometimes wait
for 2s timeout when testing with RDMA link up/down.
It is possible when a smc_link is in ACTIVATING state,
the underlaying QP is still in RESET or RTR state, which
cannot send any messages out.
smc_llc_send_link_delete_all() use smc_link_usable() to
checks whether the link is usable, if the QP is still in
RESET or RTR state, but the smc_link is in ACTIVATING, this
LLC message will always fail without any CQE entering the
CQ, and we will always wait 2s before timeout.
Since we cannot send any messages through the QP before
the QP enter RTS. I add a wrapper smc_link_sendable()
which checks the state of QP along with the link state.
And replace smc_link_usable() with smc_link_sendable()
in all LLC & CDC message sending routine.
Fixes: 5f08318f61 ("smc: connection data control (CDC)")
Signed-off-by: Dust Li <dust.li@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95f7f3e7dc ]
Commit 8f3d65c166 ("net/smc: fix wait on already cleared link")
introduced link refcounting to avoid waits on already cleared links.
This patch extents and improves the refcounting to cover all
remaining possible cases for this kind of error situation.
Fixes: 15e1b99aad ("net/smc: no WR buffer wait for terminating link group")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5be60a9453 ]
Received frames have FCS truncated. There is no need
to subtract FCS length from the statistics.
Fixes: fe1a56420c ("net: lantiq: Add Lantiq / Intel VRX200 Ethernet driver")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1cd5384c88 ]
'ndev' is a managed resource allocated with devm_alloc_etherdev(), so there
is no need to call free_netdev() explicitly or there will be a double
free().
Simplify all error handling paths accordingly.
Fixes: d51b6ce441 ("net: ethernet: add ag71xx driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca506fca46 ]
The D-Link DSB-650TX (2001:4002) is unable to receive Ethernet frames
that are longer than 1518 octets, for example, Ethernet frames that
contain 802.1Q VLAN tags.
The frames are sent to the pegasus driver via USB but the driver
discards them because they have the Long_pkt field set to 1 in the
received status report. The function read_bulk_callback of the pegasus
driver treats such received "packets" (in the terminology of the
hardware) as errors but the field simply does just indicate that the
Ethernet frame (MAC destination to FCS) is longer than 1518 octets.
It seems that in the 1990s there was a distinction between
"giant" (> 1518) and "runt" (< 64) frames and the hardware includes
flags to indicate this distinction. It seems that the purpose of the
distinction "giant" frames was to not allow infinitely long frames due
to transmission errors and to allow hardware to have an upper limit of
the frame size. However, the hardware already has such limit with its
2048 octet receive buffer and, therefore, Long_pkt is merely a
convention and should not be treated as a receive error.
Actually, the hardware is even able to receive Ethernet frames with 2048
octets which exceeds the claimed limit frame size limit of the driver of
1536 octets (PEGASUS_MTU).
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Matthias-Christian Ott <ott@mirix.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d7373dabf ]
In smc_wr_tx_send_wait() the completion on index specified by
pend->idx is initialized and after smc_wr_tx_send() was called the wait
for completion starts. pend->idx is used to get the correct index for
the wait, but the pend structure could already be cleared in
smc_wr_tx_process_cqe().
Introduce pnd_idx to hold and use a local copy of the correct index.
Fixes: 09c61d24f9 ("net/smc: wait for departure of an IB message")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ec7d18d18 ]
This patch is to delay the endpoint free by calling call_rcu() to fix
another use-after-free issue in sctp_sock_dump():
BUG: KASAN: use-after-free in __lock_acquire+0x36d9/0x4c20
Call Trace:
__lock_acquire+0x36d9/0x4c20 kernel/locking/lockdep.c:3218
lock_acquire+0x1ed/0x520 kernel/locking/lockdep.c:3844
__raw_spin_lock_bh include/linux/spinlock_api_smp.h:135 [inline]
_raw_spin_lock_bh+0x31/0x40 kernel/locking/spinlock.c:168
spin_lock_bh include/linux/spinlock.h:334 [inline]
__lock_sock+0x203/0x350 net/core/sock.c:2253
lock_sock_nested+0xfe/0x120 net/core/sock.c:2774
lock_sock include/net/sock.h:1492 [inline]
sctp_sock_dump+0x122/0xb20 net/sctp/diag.c:324
sctp_for_each_transport+0x2b5/0x370 net/sctp/socket.c:5091
sctp_diag_dump+0x3ac/0x660 net/sctp/diag.c:527
__inet_diag_dump+0xa8/0x140 net/ipv4/inet_diag.c:1049
inet_diag_dump+0x9b/0x110 net/ipv4/inet_diag.c:1065
netlink_dump+0x606/0x1080 net/netlink/af_netlink.c:2244
__netlink_dump_start+0x59a/0x7c0 net/netlink/af_netlink.c:2352
netlink_dump_start include/linux/netlink.h:216 [inline]
inet_diag_handler_cmd+0x2ce/0x3f0 net/ipv4/inet_diag.c:1170
__sock_diag_cmd net/core/sock_diag.c:232 [inline]
sock_diag_rcv_msg+0x31d/0x410 net/core/sock_diag.c:263
netlink_rcv_skb+0x172/0x440 net/netlink/af_netlink.c:2477
sock_diag_rcv+0x2a/0x40 net/core/sock_diag.c:274
This issue occurs when asoc is peeled off and the old sk is freed after
getting it by asoc->base.sk and before calling lock_sock(sk).
To prevent the sk free, as a holder of the sk, ep should be alive when
calling lock_sock(). This patch uses call_rcu() and moves sock_put and
ep free into sctp_endpoint_destroy_rcu(), so that it's safe to try to
hold the ep under rcu_read_lock in sctp_transport_traverse_process().
If sctp_endpoint_hold() returns true, it means this ep is still alive
and we have held it and can continue to dump it; If it returns false,
it means this ep is dead and can be freed after rcu_read_unlock, and
we should skip it.
In sctp_sock_dump(), after locking the sk, if this ep is different from
tsp->asoc->ep, it means during this dumping, this asoc was peeled off
before calling lock_sock(), and the sk should be skipped; If this ep is
the same with tsp->asoc->ep, it means no peeloff happens on this asoc,
and due to lock_sock, no peeloff will happen either until release_sock.
Note that delaying endpoint free won't delay the port release, as the
port release happens in sctp_endpoint_destroy() before calling call_rcu().
Also, freeing endpoint by call_rcu() makes it safe to access the sk by
asoc->base.sk in sctp_assocs_seq_show() and sctp_rcv().
Thanks Jones to bring this issue up.
v1->v2:
- improve the changelog.
- add kfree(ep) into sctp_endpoint_destroy_rcu(), as Jakub noticed.
Reported-by: syzbot+9276d76e83e3bcde6c99@syzkaller.appspotmail.com
Reported-by: Lee Jones <lee.jones@linaro.org>
Fixes: d25adbeb0c ("sctp: fix an use-after-free issue in sctp_sock_dump")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5471d5226c ]
The below referenced commit correctly updated the computation of number
of segments (gso_size) by using only the gso payload size and
removing the header lengths.
With this change the regression test started failing. Update
the tests to match this new behavior.
Both IPv4 and IPv6 tests are updated, as a separate patch in this series
will update udp_v6_send_skb to match this change in udp_send_skb.
Fixes: 158390e456 ("udp: using datalen to cap max gso segments")
Signed-off-by: Coco Li <lixiaoyan@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20211223222441.2975883-2-lixiaoyan@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 736ef37fd9 ]
The max number of UDP gso segments is intended to cap to
UDP_MAX_SEGMENTS, this is checked in udp_send_skb().
skb->len contains network and transport header len here, we should use
only data len instead.
This is the ipv6 counterpart to the below referenced commit,
which missed the ipv6 change
Fixes: 158390e456 ("udp: using datalen to cap max gso segments")
Signed-off-by: Coco Li <lixiaoyan@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20211223222441.2975883-1-lixiaoyan@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19c4aba2d4 ]
There are two ICOSQs per channel: one is needed for RX, and the other
for async operations (XSK TX, kTLS offload). Currently, the recovery
flow for both is the same, and async ICOSQ is mistakenly treated like
the regular ICOSQ.
This patch prevents running the regular ICOSQ recovery on async ICOSQ.
The purpose of async ICOSQ is to handle XSK wakeup requests and post
kTLS offload RX parameters, it has nothing to do with RQ and XSKRQ UMRs,
so the regular recovery sequence is not applicable here.
Fixes: be5323c837 ("net/mlx5e: Report and recover from CQE error on ICOSQ")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 732bc2ff08 upstream.
Clang static analysis reports this warning
hooks.c:5765:6: warning: 4th function call argument is an uninitialized
value
if (selinux_xfrm_postroute_last(sksec->sid, skb, &ad, proto))
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
selinux_parse_skb() can return ok without setting proto. The later call
to selinux_xfrm_postroute_last() does an early check of proto and can
return ok if the garbage proto value matches. So initialize proto.
Cc: stable@vger.kernel.org
Fixes: eef9b41622 ("selinux: cleanup selinux_xfrm_sock_rcv_skb() and selinux_xfrm_postroute_last()")
Signed-off-by: Tom Rix <trix@redhat.com>
[PM: typo/spelling and checkpatch.pl description fixes]
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4eb1782eaa upstream.
Commit 85bf17b28f ("recordmcount.pl: look for jgnop instruction as well
as bcrl on s390") added a new alternative mnemonic for the existing brcl
instruction. This is required for the combination old gcc version (pre 9.0)
and binutils since version 2.37.
However at the same time this commit introduced a typo, replacing brcl with
bcrl. As a result no mcount locations are detected anymore with old gcc
versions (pre 9.0) and binutils before version 2.37.
Fix this by using the correct mnemonic again.
Reported-by: Miroslav Benes <mbenes@suse.cz>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: <stable@vger.kernel.org>
Fixes: 85bf17b28f ("recordmcount.pl: look for jgnop instruction as well as bcrl on s390")
Link: https://lore.kernel.org/r/alpine.LSU.2.21.2112230949520.19849@pobox.suse.cz
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d7f55471db ]
Fix modpost Section mismatch error in memblock_phys_alloc()
[...]
WARNING: modpost: vmlinux.o(.text.unlikely+0x1dcc): Section mismatch in reference
from the function memblock_phys_alloc() to the function .init.text:memblock_phys_alloc_range()
The function memblock_phys_alloc() references
the function __init memblock_phys_alloc_range().
This is often because memblock_phys_alloc lacks a __init
annotation or the annotation of memblock_phys_alloc_range is wrong.
ERROR: modpost: Section mismatches detected.
Set CONFIG_SECTION_MISMATCH_WARN_ONLY=y to allow them.
[...]
memblock_phys_alloc() is a one-line wrapper, make it __always_inline to
avoid these section mismatches.
Reported-by: k2ci <kernel-bot@kylinos.cn>
Suggested-by: Mike Rapoport <rppt@kernel.org>
Signed-off-by: Jackie Liu <liuyun01@kylinos.cn>
[rppt: slightly massaged changelog ]
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Link: https://lore.kernel.org/r/20211217020754.2874872-1-liu.yun@linux.dev
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 484730e586 ]
When a trap 7 (Instruction access rights) occurs, this means the CPU
couldn't execute an instruction due to missing execute permissions on
the memory region. In this case it seems the CPU didn't even fetched
the instruction from memory and thus did not store it in the cr19 (IIR)
register before calling the trap handler. So, the trap handler will find
some random old stale value in cr19.
This patch simply overwrites the stale IIR value with a constant magic
"bad food" value (0xbaadf00d), in the hope people don't start to try to
understand the various random IIR values in trap 7 dumps.
Noticed-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f702e11076 ]
hwight16() is much faster. While we are at it, no need to include
"perm =" part into data_race() macro, for perm is a local variable
that cannot be accessed by other threads.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04e57a2d95 ]
If tomoyo is used in a testing/fuzzing environment in learning mode,
for lots of domains the quota will be exceeded and stay exceeded
for prolonged periods of time. In such cases it's pointless (and slow)
to walk the whole acl list again and again just to rediscover that
the quota is exceeded. We already have the TOMOYO_DIF_QUOTA_WARNED flag
that notes the overflow condition. Check it early to avoid the slowdown.
[penguin-kernel]
This patch causes a user visible change that the learning mode will not be
automatically resumed after the quota is increased. To resume the learning
mode, administrator will need to explicitly clear TOMOYO_DIF_QUOTA_WARNED
flag after increasing the quota. But I think that this change is generally
preferable, for administrator likely wants to optimize the acl list for
that domain before increasing the quota, or that domain likely hits the
quota again. Therefore, don't try to care to clear TOMOYO_DIF_QUOTA_WARNED
flag automatically when the quota for that domain changed.
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9222ba68c3 ]
We've got a bug report about the non-working keyboard on ASUS ZenBook
UX425UA. It seems that the PS/2 device isn't ready immediately at
boot but takes some seconds to get ready. Until now, the only
workaround is to defer the probe, but it's available only when the
driver is a module. However, many distros, including openSUSE as in
the original report, build the PS/2 input drivers into kernel, hence
it won't work easily.
This patch adds the support for the deferred probe for i8042 stuff as
a workaround of the problem above. When the deferred probe mode is
enabled and the device couldn't be probed, it'll be repeated with the
standard deferred probe mechanism.
The deferred probe mode is enabled either via the new option
i8042.probe_defer or via the quirk table entry. As of this patch, the
quirk table contains only ASUS ZenBook UX425UA.
The deferred probe part is based on Fabio's initial work.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1190256
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Samuel Čavoj <samuel@cavoj.net>
Link: https://lore.kernel.org/r/20211117063757.11380-1-tiwai@suse.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
The drm edid parser doesn't signal RGB support on DVI monitors
with old edid versions, leading to 8-bit RGB mode being rejected
and no video on DVI monitors.
As 8-bit RGB is mandatory on HDMI and DVI monitors anyways we can
simply drop the RGB format check, aligning vc4 with other drivers.
Signed-off-by: Matthias Reichl <hias@horus.com>
When vc4_hdmi_connector_detect() was called in
connector_status_connected state it incorrectly cleared the
hdmi_monitor flag, leading to no audio on RPi3.
Fix this by clearing hdmi_monitor only when the hpd check
indicated no connection or if reading the edid failed.
Signed-off-by: Matthias Reichl <hias@horus.com>
commit 75a2f31520 upstream.
This ioctl() implicitly assumed that the socket was already bound to
a valid local socket name, i.e. Phonet object. If the socket was not
bound, two separate problems would occur:
1) We'd send an pipe enablement request with an invalid source object.
2) Later socket calls could BUG on the socket unexpectedly being
connected yet not bound to a valid object.
Reported-by: syzbot+2dc91e7fc3dea88b1e8a@syzkaller.appspotmail.com
Signed-off-by: Rémi Denis-Courmont <remi@remlab.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2f37aead1 upstream.
The previous commit 3e0588c291 ("hamradio: defer ax25 kfree after
unregister_netdev") reorder the kfree operations and unregister_netdev
operation to prevent UAF.
This commit improves the previous one by also deferring the nullify of
the ax->tty pointer. Otherwise, a NULL pointer dereference bug occurs.
Partial of the stack trace is shown below.
BUG: kernel NULL pointer dereference, address: 0000000000000538
RIP: 0010:ax_xmit+0x1f9/0x400
...
Call Trace:
dev_hard_start_xmit+0xec/0x320
sch_direct_xmit+0xea/0x240
__qdisc_run+0x166/0x5c0
__dev_queue_xmit+0x2c7/0xaf0
ax25_std_establish_data_link+0x59/0x60
ax25_connect+0x3a0/0x500
? security_socket_connect+0x2b/0x40
__sys_connect+0x96/0xc0
? __hrtimer_init+0xc0/0xc0
? common_nsleep+0x2e/0x50
? switch_fpu_return+0x139/0x1a0
__x64_sys_connect+0x11/0x20
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xa9
The crash point is shown as below
static void ax_encaps(...) {
...
set_bit(TTY_DO_WRITE_WAKEUP, &ax->tty->flags); // ax->tty = NULL!
...
}
By placing the nullify action after the unregister_netdev, the ax->tty
pointer won't be assigned as NULL net_device framework layer is well
synchronized.
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e0588c291 upstream.
There is a possible race condition (use-after-free) like below
(USE) | (FREE)
ax25_sendmsg |
ax25_queue_xmit |
dev_queue_xmit |
__dev_queue_xmit |
__dev_xmit_skb |
sch_direct_xmit | ...
xmit_one |
netdev_start_xmit | tty_ldisc_kill
__netdev_start_xmit | mkiss_close
ax_xmit | kfree
ax_encaps |
|
Even though there are two synchronization primitives before the kfree:
1. wait_for_completion(&ax->dead). This can prevent the race with
routines from mkiss_ioctl. However, it cannot stop the routine coming
from upper layer, i.e., the ax25_sendmsg.
2. netif_stop_queue(ax->dev). It seems that this line of code aims to
halt the transmit queue but it fails to stop the routine that already
being xmit.
This patch reorder the kfree after the unregister_netdev to avoid the
possible UAF as the unregister_netdev() is well synchronized and won't
return if there is a running routine.
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ade48d0c2 upstream.
The existing cleanup routine implementation is not well synchronized
with the syscall routine. When a device is detaching, below race could
occur.
static int ax25_sendmsg(...) {
...
lock_sock()
ax25 = sk_to_ax25(sk);
if (ax25->ax25_dev == NULL) // CHECK
...
ax25_queue_xmit(skb, ax25->ax25_dev->dev); // USE
...
}
static void ax25_kill_by_device(...) {
...
if (s->ax25_dev == ax25_dev) {
s->ax25_dev = NULL;
...
}
Other syscall functions like ax25_getsockopt, ax25_getname,
ax25_info_show also suffer from similar races. To fix them, this patch
introduce lock_sock() into ax25_kill_by_device in order to guarantee
that the nullify action in cleanup routine cannot proceed when another
socket request is pending.
Signed-off-by: Hanjie Wu <nagi@zju.edu.cn>
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cdc5287aca upstream.
Bit 7 of the status register indicates that the chip is busy
doing a conversion. It does not indicate an alarm status.
Stop reporting it as alarm status bit.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da7dc05684 upstream.
Tests with a real chip and a closer look into the datasheet reveals
that the local and remote critical alarm status bits are swapped for
MAX6680/MAX6681.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ff29701ff upstream.
Update the documentation for kvm-intel's emulate_invalid_guest_state to
rectify the description of KVM's default behavior, and to document that
the behavior and thus parameter only applies to L1.
Fixes: a27685c33a ("KVM: VMX: Emulate invalid guest state by default")
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211207193006.120997-4-seanjc@google.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 890d5b4090 upstream.
When listening for notifications through netlink of a new interface being
registered, sporadically, it is possible for the MAC to be read as zero.
The zero MAC address lasts a short period of time and then switches to a
valid random MAC address.
This causes problems for netd in Android, which assumes that the interface
is malfunctioning and will not use it.
In the good case we get this log:
InterfaceController::getCfg() ifName usb0
hwAddr 92:a8:f0:73:79:5b ipv4Addr 0.0.0.0 flags 0x1002
In the error case we get these logs:
InterfaceController::getCfg() ifName usb0
hwAddr 00:00:00:00:00:00 ipv4Addr 0.0.0.0 flags 0x1002
netd : interfaceGetCfg("usb0")
netd : interfaceSetCfg() -> ServiceSpecificException
(99, "[Cannot assign requested address] : ioctl() failed")
The reason for the issue is the order in which the interface is setup,
it is first registered through register_netdev() and after the MAC
address is set.
Fixed by first setting the MAC address of the net_device and after that
calling register_netdev().
Fixes: bcd4a1c40b ("usb: gadget: u_ether: construct with default values and add setters/getters")
Cc: stable@vger.kernel.org
Signed-off-by: Marian Postevca <posteuca@mutex.one>
Link: https://lore.kernel.org/r/20211204214912.17627-1-posteuca@mutex.one
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd84bfdddd upstream.
Ceph always inherits the SGID bit if it is set on the parent inode,
while the generic inode_init_owner does not do this in a few cases where
it can create a possible security problem (cf. [1]).
Update ceph to strip the SGID bit just as inode_init_owner would.
This bug was detected by the mapped mount testsuite in [3]. The
testsuite tests all core VFS functionality and semantics with and
without mapped mounts. That is to say it functions as a generic VFS
testsuite in addition to a mapped mount testsuite. While working on
mapped mount support for ceph, SIGD inheritance was the only failing
test for ceph after the port.
The same bug was detected by the mapped mount testsuite in XFS in
January 2021 (cf. [2]).
[1]: commit 0fa3ecd878 ("Fix up non-directory creation in SGID directories")
[2]: commit 01ea173e10 ("xfs: fix up non-directory creation in SGID directories")
[3]: https://git.kernel.org/fs/xfs/xfstests-dev.git
Cc: stable@vger.kernel.org
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5598b24efaf4892741c798b425d543e4bed357a1 upstream.
As Wenqing Liu reported in bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=215235
- Overview
page fault in f2fs_setxattr() when mount and operate on corrupted image
- Reproduce
tested on kernel 5.16-rc3, 5.15.X under root
1. unzip tmp7.zip
2. ./single.sh f2fs 7
Sometimes need to run the script several times
- Kernel dump
loop0: detected capacity change from 0 to 131072
F2FS-fs (loop0): Found nat_bits in checkpoint
F2FS-fs (loop0): Mounted with checkpoint version = 7548c2ee
BUG: unable to handle page fault for address: ffffe47bc7123f48
RIP: 0010:kfree+0x66/0x320
Call Trace:
__f2fs_setxattr+0x2aa/0xc00 [f2fs]
f2fs_setxattr+0xfa/0x480 [f2fs]
__f2fs_set_acl+0x19b/0x330 [f2fs]
__vfs_removexattr+0x52/0x70
__vfs_removexattr_locked+0xb1/0x140
vfs_removexattr+0x56/0x100
removexattr+0x57/0x80
path_removexattr+0xa3/0xc0
__x64_sys_removexattr+0x17/0x20
do_syscall_64+0x37/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
The root cause is in __f2fs_setxattr(), we missed to do sanity check on
last xattr entry, result in out-of-bound memory access during updating
inconsistent xattr data of target inode.
After the fix, it can detect such xattr inconsistency as below:
F2FS-fs (loop11): inode (7) has invalid last xattr entry, entry_size: 60676
F2FS-fs (loop11): inode (8) has corrupted xattr
F2FS-fs (loop11): inode (8) has corrupted xattr
F2FS-fs (loop11): inode (8) has invalid last xattr entry, entry_size: 47736
Cc: stable@vger.kernel.org
Reported-by: Wenqing Liu <wenqingliu0120@gmail.com>
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 18549bf4b2 upstream.
Pointer to the allocated pages (struct page *page) has already
progressed towards the end of allocation. It is incorrect to perform
__free_pages(page, order) using this pointer as we would free any
arbitrary pages. Fix this by stop modifying the page pointer.
Fixes: ec185dd3ab ("optee: Fix memory leak when failing to register shm pages")
Cc: stable@vger.kernel.org
Reported-by: Patrik Lantz <patrik.lantz@axis.com>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a57d83c78 upstream.
Hulk Robot reported a panic in put_page_testzero() when testing
madvise() with MADV_SOFT_OFFLINE. The BUG() is triggered when retrying
get_any_page(). This is because we keep MF_COUNT_INCREASED flag in
second try but the refcnt is not increased.
page dumped because: VM_BUG_ON_PAGE(page_ref_count(page) == 0)
------------[ cut here ]------------
kernel BUG at include/linux/mm.h:737!
invalid opcode: 0000 [#1] PREEMPT SMP
CPU: 5 PID: 2135 Comm: sshd Tainted: G B 5.16.0-rc6-dirty #373
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014
RIP: release_pages+0x53f/0x840
Call Trace:
free_pages_and_swap_cache+0x64/0x80
tlb_flush_mmu+0x6f/0x220
unmap_page_range+0xe6c/0x12c0
unmap_single_vma+0x90/0x170
unmap_vmas+0xc4/0x180
exit_mmap+0xde/0x3a0
mmput+0xa3/0x250
do_exit+0x564/0x1470
do_group_exit+0x3b/0x100
__do_sys_exit_group+0x13/0x20
__x64_sys_exit_group+0x16/0x20
do_syscall_64+0x34/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
Modules linked in:
---[ end trace e99579b570fe0649 ]---
RIP: 0010:release_pages+0x53f/0x840
Link: https://lkml.kernel.org/r/20211221074908.3910286-1-liushixin2@huawei.com
Fixes: b94e02822d ("mm,hwpoison: try to narrow window race for free pages")
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Acked-by: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8536a5ef88 upstream.
The Thumb2 version of the FP exception handling entry code treats the
register holding the CP number (R8) differently, resulting in the iWMMXT
CP number check to be incorrect.
Fix this by unifying the ARM and Thumb2 code paths, and switch the
order of the additions of the TI_USED_CP offset and the shifted CP
index.
Cc: <stable@vger.kernel.org>
Fixes: b86040a59f ("Thumb-2: Implementation of the unified start-up and exceptions code")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f89b548ca6 upstream.
The vendor driver implements special handling for multi-block
SD_IO_RW_EXTENDED (and SD_IO_RW_DIRECT) commands which have data
attached to them. It sets the MANUAL_STOP bit in the MESON_SDHC_MISC
register for these commands. In all other cases this bit is cleared.
Here we omit SD_IO_RW_DIRECT since that command never has any data
attached to it.
This fixes SDIO wifi using the brcmfmac driver which reported the
following error without this change on a Netxeon S82 board using a
Meson8 (S802) SoC:
brcmf_fw_alloc_request: using brcm/brcmfmac43362-sdio for chip
BCM43362/1
brcmf_sdiod_ramrw: membytes transfer failed
brcmf_sdio_download_code_file: error -110 on writing 219557 membytes
at 0x00000000
brcmf_sdio_download_firmware: dongle image file download failed
And with this change:
brcmf_fw_alloc_request: using brcm/brcmfmac43362-sdio for chip
BCM43362/1
brcmf_c_process_clm_blob: no clm_blob available (err=-2), device may
have limited channels available
brcmf_c_preinit_dcmds: Firmware: BCM43362/1 wl0: Apr 22 2013 14:50:00
version 5.90.195.89.6 FWID 01-b30a427d
Fixes: e4bf1b0970 ("mmc: host: meson-mx-sdhc: new driver for the Amlogic Meson SDHC host")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211219153442.463863-2-martin.blumenstingl@googlemail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a5875f14b upstream.
When replugging the device the following message shows up:
gpio gpiochip2: (dln2): detected irqchip that is shared with multiple gpiochips: please fix the driver.
This also has the effect that interrupts won't work.
The same problem would also show up if multiple devices where plugged in.
Fix this by allocating the irq_chip data structure per instance like other
drivers do.
I don't know when this problem appeared, but it is present in 5.10.
Cc: <stable@vger.kernel.org> # 5.10+
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fdba608f15 upstream.
Drop a check that guards triggering a posted interrupt on the currently
running vCPU, and more importantly guards waking the target vCPU if
triggering a posted interrupt fails because the vCPU isn't IN_GUEST_MODE.
If a vIRQ is delivered from asynchronous context, the target vCPU can be
the currently running vCPU and can also be blocking, in which case
skipping kvm_vcpu_wake_up() is effectively dropping what is supposed to
be a wake event for the vCPU.
The "do nothing" logic when "vcpu == running_vcpu" mostly works only
because the majority of calls to ->deliver_posted_interrupt(), especially
when using posted interrupts, come from synchronous KVM context. But if
a device is exposed to the guest using vfio-pci passthrough, the VFIO IRQ
and vCPU are bound to the same pCPU, and the IRQ is _not_ configured to
use posted interrupts, wake events from the device will be delivered to
KVM from IRQ context, e.g.
vfio_msihandler()
|
|-> eventfd_signal()
|
|-> ...
|
|-> irqfd_wakeup()
|
|->kvm_arch_set_irq_inatomic()
|
|-> kvm_irq_delivery_to_apic_fast()
|
|-> kvm_apic_set_irq()
This also aligns the non-nested and nested usage of triggering posted
interrupts, and will allow for additional cleanups.
Fixes: 379a3c8ee4 ("KVM: VMX: Optimize posted-interrupt delivery for timer fastpath")
Cc: stable@vger.kernel.org
Reported-by: Longpeng (Mike) <longpeng2@huawei.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20211208015236.1616697-18-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 57690554ab upstream.
Both __pkru_allows_write() and arch_set_user_pkey_access() shift
PKRU_WD_BIT (a signed constant) by up to 30 bits, hitting the
sign bit.
Use unsigned constants instead.
Clearly pkey 15 has not been used in combination with UBSAN yet.
Noticed by code inspection only. I can't actually provoke the
compiler into generating incorrect logic as far as this shift is
concerned.
[
dhansen: add stable@ tag, plus minor changelog massaging,
For anyone doing backports, these #defines were in
arch/x86/include/asm/pgtable.h before 784a46618f.
]
Fixes: 33a709b25a ("mm/gup, x86/mm/pkeys: Check VMAs and PTEs for protection keys")
Signed-off-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20211216000856.4480-1-andrew.cooper3@citrix.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dfd0743f1d upstream.
Since the tee subsystem does not keep a strong reference to its idle
shared memory buffers, it races with other threads that try to destroy a
shared memory through a close of its dma-buf fd or by unmapping the
memory.
In tee_shm_get_from_id() when a lookup in teedev->idr has been
successful, it is possible that the tee_shm is in the dma-buf teardown
path, but that path is blocked by the teedev mutex. Since we don't have
an API to tell if the tee_shm is in the dma-buf teardown path or not we
must find another way of detecting this condition.
Fix this by doing the reference counting directly on the tee_shm using a
new refcount_t refcount field. dma-buf is replaced by using
anon_inode_getfd() instead, this separates the life-cycle of the
underlying file from the tee_shm. tee_shm_put() is updated to hold the
mutex when decreasing the refcount to 0 and then remove the tee_shm from
teedev->idr before releasing the mutex. This means that the tee_shm can
never be found unless it has a refcount larger than 0.
Fixes: 967c9cca2c ("tee: generic TEE subsystem")
Cc: stable@vger.kernel.org
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Lars Persson <larper@axis.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Reported-by: Patrik Lantz <patrik.lantz@axis.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3a5a68cff upstream.
The address bits used to select the futex spinlock need to match those used in
the LWS code in syscall.S. The mask 0x3f8 only selects 7 bits. It should
select 8 bits.
This change fixes the glibc nptl/tst-cond24 and nptl/tst-cond25 tests.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Fixes: 53a42b6324 ("parisc: Switch to more fine grained lws locks")
Cc: stable@vger.kernel.org # 5.10+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f66fce0f4 upstream.
The completer in the "or,ev %r1,%r30,%r30" instruction is reversed, so we are
not clipping the LWS number when we are called from a 32-bit process (W=0).
We need to nulify the following depdi instruction when the least-significant
bit of %r30 is 1.
If the %r20 register is not clipped, a user process could perform a LWS call
that would branch to an undefined location in the kernel and potentially crash
the machine.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # 4.19+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 34f35f8f14 upstream.
During probe ssif_info->client is dereferenced in error path. However,
it is set when some of the error checking has already been done. This
causes following kernel crash if an error path is taken:
[ 30.645593][ T674] ipmi_ssif 0-000e: ipmi_ssif: Not probing, Interface already present
[ 30.657616][ T674] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000088
...
[ 30.657723][ T674] pc : __dev_printk+0x28/0xa0
[ 30.657732][ T674] lr : _dev_err+0x7c/0xa0
...
[ 30.657772][ T674] Call trace:
[ 30.657775][ T674] __dev_printk+0x28/0xa0
[ 30.657778][ T674] _dev_err+0x7c/0xa0
[ 30.657781][ T674] ssif_probe+0x548/0x900 [ipmi_ssif 62ce4b08badc1458fd896206d9ef69a3c31f3d3e]
[ 30.657791][ T674] i2c_device_probe+0x37c/0x3c0
...
Initialize ssif_info->client before any error path can be taken. Clear
i2c_client data in the error path to prevent the dangling pointer from
leaking.
Fixes: c4436c9149 ("ipmi_ssif: avoid registering duplicate ssif interface")
Cc: stable@vger.kernel.org # 5.4.x
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Message-Id: <20211208093239.4432-1-ykaukab@suse.de>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee907afb0c upstream.
The out-of-tree vendor driver uses the following approach to set the
AIU_I2S_MISC register:
1) write AIU_MEM_I2S_START_PTR and AIU_MEM_I2S_RD_PTR
2) configure AIU_I2S_MUTE_SWAP[15:0]
3) write AIU_MEM_I2S_END_PTR
4) set AIU_I2S_MISC[2] to 1 (documented as: "put I2S interface in hold
mode")
5) set AIU_I2S_MISC[4] to 1 (depending on the driver revision it always
stays at 1 while for older drivers this bit is unset in step 4)
6) set AIU_I2S_MISC[2] to 0
7) write AIU_MEM_I2S_MASKS
8) toggle AIU_MEM_I2S_CONTROL[0]
9) toggle AIU_MEM_I2S_BUF_CNTL[0]
Move setting the AIU_I2S_MISC[2] bit to aiu_fifo_i2s_hw_params() so it
resembles the flow in the vendor kernel more closely. While here also
configure AIU_I2S_MISC[4] (documented as: "force each audio data to
left or right according to the bit attached with the audio data")
similar to how the vendor driver does this. This fixes the infamous and
long-standing "machine gun noise" issue (a buffer underrun issue).
Fixes: 6ae9ca9ce9 ("ASoC: meson: aiu: add i2s and spdif support")
Reported-by: Christian Hewitt <christianshewitt@gmail.com>
Reported-by: Geraldo Nascimento <geraldogabriel@gmail.com>
Tested-by: Christian Hewitt <christianshewitt@gmail.com>
Tested-by: Geraldo Nascimento <geraldogabriel@gmail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Cc: stable@vger.kernel.org
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20211206210804.2512999-3-martin.blumenstingl@googlemail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit edca7cc4b0 upstream.
The Clevo NJ51CU comes either with the ALC293 or the ALC256 codec, but uses
the 0x8686 subproduct id in both cases. The ALC256 codec needs a different
quirk for the headset microphone working and and edditional quirk for sound
working after suspend and resume.
When waking up from s3 suspend the Coef 0x10 is set to 0x0220 instead of
0x0020 on the ALC256 codec. Setting the value manually makes the sound
work again. This patch does this automatically.
[ minor coding style fix by tiwai ]
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Fixes: b5acfe152a ("ALSA: hda/realtek: Add some Clove SSID in the ALC293(ALC1220)")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211215191646.844644-1-wse@tuxedocomputers.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2dee54b289 upstream.
Static analysis with scan-build has found an assignment to vp2 that is
never used. It seems that the check on vp->state > 0 should be actually
on vp2->state instead. Fix this.
This dates back to 2002, I found the offending commit from the git
history git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git,
commit 91e39521bbf6 ("[PATCH] ALSA patch for 2.5.4")
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211212172025.470367-1-colin.i.king@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 16ba51b5dc ]
Tests with a real chip and a closer look into the datasheet show that
MAX6654 does not support CRIT/THERM/OVERTEMP limits, so drop support
of the respective attributes for this chip.
Introduce LM90_HAVE_CRIT flag and use it to instantiate critical limit
attributes to solve the problem.
Cc: Josh Lehan <krellan@google.com>
Fixes: 229d495d81 ("hwmon: (lm90) Add max6654 support to lm90 driver")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f347e249fc ]
A flag indicating extended temperature support makes it easier
to add support for additional chips with this functionality.
Cc: David T. Wilson <david.wilson@nasa.gov>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8344f7693 ]
TMP461 is almost identical to TMP451 and was actually detected as TMP451
with the existing lm90 driver if its I2C address is 0x4c. Add support
for it to the lm90 driver. At the same time, improve the chip detection
function to at least try to distinguish between TMP451 and TMP461.
As a side effect, this fixes commit 24333ac26d ("hwmon: (tmp401) use
smb word operations instead of 2 smb byte operations"). TMP461 does not
support word operations on temperature registers, which causes bad
temperature readings with the tmp401 driver. The lm90 driver does not
perform word operations on temperature registers and thus does not have
this problem.
Support is listed as basic because TMP461 supports a sensor resolution
of 0.0625 degrees C, while the lm90 driver assumes a resolution of 0.125
degrees C. Also, the TMP461 supports negative temperatures with its
default temperature range, which is not the case for similar chips
supported by the lm90 and the tmp401 drivers. Those limitations will be
addressed with follow-up patches.
Fixes: 24333ac26d ("hwmon: (tmp401) use smb word operations instead of 2 smb byte operations")
Reported-by: David T. Wilson <david.wilson@nasa.gov>
Cc: David T. Wilson <david.wilson@nasa.gov>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fce15c45d3 ]
The detect function had a comment "Make compiler happy" when id did not
read the second configuration register. As it turns out, the code was
checking the contents of this register for manufacturer ID 0xA1 (NXP
Semiconductor/Philips), but never actually read the register. So it
wasn't surprising that the compiler complained, and it indeed had a point.
Fix the code to read the register contents for manufacturer ID 0xa1.
At the same time, the code was reading the register for manufacturer ID
0x41 (Analog Devices), but it was not using the results. In effect it was
just checking if reading the register returned an error. That doesn't
really add much if any value, so stop doing that.
Fixes: f90be42fb3 ("hwmon: (lm90) Refactor reading of config2 register")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 266423e60e ]
...and gpio-ranges
pinctrl-bcm2835 is a combined pinctrl/gpio driver. Currently the gpio
side is registered first, but this breaks gpio hogs (which are
configured during gpiochip_add_data). Part of the hog initialisation
is a call to pinctrl_gpio_request, and since the pinctrl driver hasn't
yet been registered this results in an -EPROBE_DEFER from which it can
never recover.
Change the initialisation sequence to register the pinctrl driver
first.
This also solves a similar problem with the gpio-ranges property, which
is required in order for released pins to be returned to inputs.
Fixes: 73345a18d4 ("pinctrl: bcm2835: Pass irqchip when adding gpiochip")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211206092237.4105895-2-phil@raspberrypi.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99d7fbb5ce ]
Because platform_get_irq() could fail and return error irq.
Therefore, it might be better to check it if order to avoid the use of
error irq.
Fixes: 797047f875 ("net: ks8851: Implement Parallel bus operations")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb93b3e11d ]
Because platform_get_irq() could fail and return error irq.
Therefore, it might be better to check it if order to avoid the use of
error irq.
Fixes: ae150435b5 ("smsc: Move the SMC (SMSC) drivers")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db6d6afe38 ]
I find that platform_get_irq() will not always succeed.
It will return error irq in case of the failure.
Therefore, it might be better to check it if order to avoid the use of
error irq.
Fixes: 658d439b22 ("fjes: Introduce FUJITSU Extended Socket Network Device driver")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c15b05bae ]
When 802.3ad bond mode is configured the ad_actor_system option is set to
"00:00:00:00:00:00". But when trying to set the all-zeroes MAC as actors'
system address it was failing with EINVAL.
An all-zeroes ethernet address is valid, only multicast addresses are not
valid values.
Fixes: 171a42c38c ("bonding: add netlink support for sys prio, actor sys mac, and port key")
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/20211221111345.2462-1-ffmancera@riseup.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ed1d59211 ]
virtio_net_hdr_set_proto infers skb->protocol from the virtio_net_hdr
gso_type, to avoid packets getting dropped for lack of a proto type.
Its protocol choice is a guess, especially in the case of UFO, where
the single VIRTIO_NET_HDR_GSO_UDP label covers both UFOv4 and UFOv6.
Skip this best effort if the field is already initialized. Whether
explicitly from userspace, or implicitly based on an earlier call to
dev_parse_header_protocol (which is more robust, but was introduced
after this patch).
Fixes: 9d2f67e43b ("net/packet: fix packet drop as of virtio gso")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20211220145027.2784293-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60ec7fcfe7 ]
The return value of kcalloc() needs to be checked.
To avoid dereference of null pointer in case of the failure of alloc.
Therefore, it might be better to change the return type of
qlcnic_sriov_alloc_vlans() and return -ENOMEM when alloc fails and
return 0 the others.
Also, qlcnic_sriov_set_guest_vlan_mode() and __qlcnic_pci_sriov_enable()
should deal with the return value of qlcnic_sriov_alloc_vlans().
Fixes: 154d0c810c ("qlcnic: VLAN enhancement for 84XX adapters")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39e660687a ]
Currently, the imx6q-wandboard Ethernet does not transmit any
data.
This issue has been exposed by commit f5d9aa79df ("ARM: imx6q:
remove clk-out fixup for the Atheros AR8031 and AR8035 PHYs").
Fix it by describing the qca,clk-out-frequency property as suggested
by the commit above.
Fixes: 77591e4245 ("ARM: dts: imx6qdl-wandboard: add ethernet PHY description")
Signed-off-by: Martin Haaß <vvvrrooomm@gmail.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ebb966d3bd ]
In commit 5648b5e116 ("netfilter: nfnetlink_queue: fix OOB when mac
header was cleared"), the test for non-empty MAC header introduced in
commit 2c38de4c1f ("netfilter: fix looped (broad|multi)cast's MAC
handling") has been replaced with a test for a set MAC header.
This breaks the case when the MAC header has been reset (using
skb_reset_mac_header), as is the case with looped-back multicast
packets. As a result, the packets ending up in NFQUEUE get a bogus
hwaddr interpreted from the first bytes of the IP header.
This patch adds a test for a non-empty MAC header in addition to the
test for a set MAC header. The same two tests are also implemented in
nfnetlink_log.c, where the initial code of commit 2c38de4c1f
("netfilter: fix looped (broad|multi)cast's MAC handling") has not been
touched, but where supposedly the same situation may happen.
Fixes: 5648b5e116 ("netfilter: nfnetlink_queue: fix OOB when mac header was cleared")
Signed-off-by: Ignacy Gawędzki <ignacy.gawedzki@green-communications.fr>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9c6e071913 upstream.
Now that we can check out overlapping extents in leaf block and
out-of-order index extents in index block. But the .ee_block in the
first extent of one leaf block should equal to the .ei_block in it's
parent index extent entry. This patch add a check to verify such
inconsistent between the index and leaf block.
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Link: https://lore.kernel.org/r/20210908120850.4012324-3-yi.zhang@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8dd27feced upstream.
After commit 5946d08937 ("ext4: check for overlapping extents in
ext4_valid_extent_entries()"), we can check out the overlapping extent
entry in leaf extent blocks. But the out-of-order extent entry in index
extent blocks could also trigger bad things if the filesystem is
inconsistent. So this patch add a check to figure out the out-of-order
index extents and return error.
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Theodore Ts'o <tytso@mit.edu>
Link: https://lore.kernel.org/r/20210908120850.4012324-2-yi.zhang@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f2f87d51a upstream.
In the most error path of current extents updating operations are not
roll back partial updates properly when some bad things happens(.e.g in
ext4_ext_insert_extent()). So we may get an inconsistent extents tree
if journal has been aborted due to IO error, which may probability lead
to BUGON later when we accessing these extent entries in errors=continue
mode. This patch drop extent buffer's verify flag before updatng the
contents in ext4_ext_get_access(), and reset it after updating in
__ext4_ext_dirty(). After this patch we could force to check the extent
buffer if extents tree updating was break off, make sure the extents are
consistent.
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Theodore Ts'o <tytso@mit.edu>
Link: https://lore.kernel.org/r/20210908120850.4012324-4-yi.zhang@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e6f8d1fa1 upstream.
Similar to
commit 231ad7f409 ("Makefile: infer --target from ARCH for CC=clang")
There really is no point in setting --target based on
$CROSS_COMPILE_COMPAT for clang when the integrated assembler is being
used, since
commit ef94340583 ("arm64: vdso32: drop -no-integrated-as flag").
Allows COMPAT_VDSO to be selected without setting $CROSS_COMPILE_COMPAT
when using clang and lld together.
Before:
$ ARCH=arm64 CROSS_COMPILE_COMPAT=arm-linux-gnueabi- make -j72 LLVM=1 defconfig
$ grep CONFIG_COMPAT_VDSO .config
CONFIG_COMPAT_VDSO=y
$ ARCH=arm64 make -j72 LLVM=1 defconfig
$ grep CONFIG_COMPAT_VDSO .config
$
After:
$ ARCH=arm64 CROSS_COMPILE_COMPAT=arm-linux-gnueabi- make -j72 LLVM=1 defconfig
$ grep CONFIG_COMPAT_VDSO .config
CONFIG_COMPAT_VDSO=y
$ ARCH=arm64 make -j72 LLVM=1 defconfig
$ grep CONFIG_COMPAT_VDSO .config
CONFIG_COMPAT_VDSO=y
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Suggested-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Link: https://lore.kernel.org/r/20211019223646.1146945-5-ndesaulniers@google.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a regression introduced in 131f132203
(see also https://github.com/raspberrypi/linux/issues/4791).
The tc358743 driver refused to bind to the device. The irs1125
driver is likely behaving similarly.
The new unified cam1_clk node that represents the fixed on-board
oscillator is marked as disabled by default. These overlays didn't
expect this and so the clock nodes were stuck in disabled state.
This commit just adds the required status = "okay" line. Other sensor
drivers do this too.
commit be81992f90 upstream.
In case a guest isn't consuming incoming network traffic as fast as it
is coming in, xen-netback is buffering network packages in unlimited
numbers today. This can result in host OOM situations.
Commit f48da8b14d ("xen-netback: fix unlimited guest Rx internal
queue and carrier flapping") meant to introduce a mechanism to limit
the amount of buffered data by stopping the Tx queue when reaching the
data limit, but this doesn't work for cases like UDP.
When hitting the limit don't queue further SKBs, but drop them instead.
In order to be able to tell Rx packages have been dropped increment the
rx_dropped statistics counter in this case.
It should be noted that the old solution to continue queueing SKBs had
the additional problem of an overflow of the 32-bit rx_queue_len value
would result in intermittent Tx queue enabling.
This is part of XSA-392
Fixes: f48da8b14d ("xen-netback: fix unlimited guest Rx internal queue and carrier flapping")
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6032046ec4 upstream.
Commit 1d5d485239 ("xen-netback: require fewer guest Rx slots when
not using GSO") introduced a security problem in netback, as an
interface would only be regarded to be stalled if no slot is available
in the rx queue ring page. In case the SKB at the head of the queued
requests will need more than one rx slot and only one slot is free the
stall detection logic will never trigger, as the test for that is only
looking for at least one slot to be free.
Fix that by testing for the needed number of slots instead of only one
slot being available.
In order to not have to take the rx queue lock that often, store the
number of needed slots in the queue data. As all SKB dequeue operations
happen in the rx queue kernel thread this is safe, as long as the
number of needed slots is accessed via READ/WRITE_ONCE() only and
updates are always done with the rx queue lock held.
Add a small helper for obtaining the number of free slots.
This is part of XSA-392
Fixes: 1d5d485239 ("xen-netback: require fewer guest Rx slots when not using GSO")
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe415186b4 upstream.
The Xen console driver is still vulnerable for an attack via excessive
number of events sent by the backend. Fix that by using a lateeoi event
channel.
For the normal domU initial console this requires the introduction of
bind_evtchn_to_irq_lateeoi() as there is no xenbus device available
at the time the event channel is bound to the irq.
As the decision whether an interrupt was spurious or not requires to
test for bytes having been read from the backend, move sending the
event into the if statement, as sending an event without having found
any bytes to be read is making no sense at all.
This is part of XSA-391
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b27d47950e upstream.
The Xen netfront driver is still vulnerable for an attack via excessive
number of events sent by the backend. Fix that by using lateeoi event
channels.
For being able to detect the case of no rx responses being added while
the carrier is down a new lock is needed in order to update and test
rsp_cons and the number of seen unconsumed responses atomically.
This is part of XSA-391
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0fd08a34e8 upstream.
The Xen blkfront driver is still vulnerable for an attack via excessive
number of events sent by the backend. Fix that by using lateeoi event
channels.
This is part of XSA-391
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b1da99b84 upstream.
Fix drivers/bus/ti-sysc.c:2494:13: error: variable 'error' set but not
used introduced by commit 9d88136120 ("bus: ti-sysc: Add quirk handling
for reinit on context lost").
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f5573cfe7 upstream.
Syzbot triggered the following warning in ovl_workdir_create() ->
ovl_create_real():
if (!err && WARN_ON(!newdentry->d_inode)) {
The reason is that the cgroup2 filesystem returns from mkdir without
instantiating the new dentry.
Weird filesystems such as this will be rejected by overlayfs at a later
stage during setup, but to prevent such a warning, call ovl_mkdir_real()
directly from ovl_workdir_create() and reject this case early.
Reported-and-tested-by: syzbot+75eab84fd0af9e8bf66b@syzkaller.appspotmail.com
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 44870a9e7a upstream.
Syzbot reported, that mxl111sf_ctrl_msg() uses uninitialized
mutex. The problem was in wrong mutex_init() location.
Previous mutex_init(&state->msg_lock) call was in ->init() function, but
dvb_usbv2_init() has this order of calls:
dvb_usbv2_init()
dvb_usbv2_adapter_init()
dvb_usbv2_adapter_frontend_init()
props->frontend_attach()
props->init()
Since mxl111sf_* devices call mxl111sf_ctrl_msg() in ->frontend_attach()
internally we need to initialize state->msg_lock before
frontend_attach(). To achieve it, ->probe() call added to all mxl111sf_*
devices, which will simply initiaize mutex.
Reported-and-tested-by: syzbot+5ca0bf339f13c4243001@syzkaller.appspotmail.com
Fixes: 8572211842 ("[media] mxl111sf: convert to new DVB USB")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd0687c18e upstream.
Do not sleep in poll() when the need_wakeup flag is set. When this
flag is set, the application needs to explicitly wake up the driver
with a syscall (poll, recvmsg, sendmsg, etc.) to guarantee that Rx
and/or Tx processing will be processed promptly. But the current code
in poll(), sleeps first then wakes up the driver. This means that no
driver processing will occur (baring any interrupts) until the timeout
has expired.
Fix this by checking the need_wakeup flag first and if set, wake the
driver and return to the application. Only if need_wakeup is not set
should the process sleep if there is a timeout set in the poll() call.
Fixes: 77cd0d7b3f ("xsk: add support for need_wakeup flag in AF_XDP rings")
Reported-by: Keith Wiles <keith.wiles@intel.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/bpf/20211214102607.7677-1-magnus.karlsson@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 737e65c795 upstream.
According to the i.MX6ULL Reference Manual, pad CSI_DATA07 may
have the ESAI_TX0 functionality, not ESAI_T0.
Also, NXP's i.MX Config Tools 10.0 generates dtsi with the
MX6ULL_PAD_CSI_DATA07__ESAI_TX0 naming, so fix it accordingly.
There are no devicetree users in mainline that use the old name,
so just remove the old entry.
Fixes: c201369d4a ("ARM: dts: imx6ull: add imx6ull support")
Reported-by: George Makarov <georgemakarov1@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a02dcde595 upstream.
A new warning in clang points out a few places in this driver where a
bitwise OR is being used with boolean types:
drivers/input/touchscreen.c:81:17: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
data_present = touchscreen_get_prop_u32(dev, "touchscreen-min-x",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
This use of a bitwise OR is intentional, as bitwise operations do not
short circuit, which allows all the calls to touchscreen_get_prop_u32()
to happen so that the last parameter is initialized while coalescing the
results of the calls to make a decision after they are all evaluated.
To make this clearer to the compiler, use the '|=' operator to assign
the result of each touchscreen_get_prop_u32() call to data_present,
which keeps the meaning of the code the same but makes it obvious that
every one of these calls is expected to happen.
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20211014205757.3474635-1-nathan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e8c11b6b3 upstream.
Even after commit e1d7ba8735 ("time: Always make sure wall_to_monotonic
isn't positive") it is still possible to make wall_to_monotonic positive
by running the following code:
int main(void)
{
struct timespec time;
clock_gettime(CLOCK_MONOTONIC, &time);
time.tv_nsec = 0;
clock_settime(CLOCK_REALTIME, &time);
return 0;
}
The reason is that the second parameter of timespec64_compare(), ts_delta,
may be unnormalized because the delta is calculated with an open coded
substraction which causes the comparison of tv_sec to yield the wrong
result:
wall_to_monotonic = { .tv_sec = -10, .tv_nsec = 900000000 }
ts_delta = { .tv_sec = -9, .tv_nsec = -900000000 }
That makes timespec64_compare() claim that wall_to_monotonic < ts_delta,
but actually the result should be wall_to_monotonic > ts_delta.
After normalization, the result of timespec64_compare() is correct because
the tv_sec comparison is not longer misleading:
wall_to_monotonic = { .tv_sec = -10, .tv_nsec = 900000000 }
ts_delta = { .tv_sec = -10, .tv_nsec = 100000000 }
Use timespec64_sub() to ensure that ts_delta is normalized, which fixes the
issue.
Fixes: e1d7ba8735 ("time: Always make sure wall_to_monotonic isn't positive")
Signed-off-by: Yu Liao <liaoyu15@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211213135727.1656662-1-liaoyu15@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c33ff7288 upstream.
Commit fab8a02b73 ("serial: 8250_fintek: Enable high speed mode on Fintek F81866")
introduced support to use high baudrate with Fintek SuperIO UARTs. It'll
change clocksources when the UART probed.
But when user add kernel parameter "console=ttyS0,115200 console=tty0" to make
the UART as console output, the console will output garbled text after the
following kernel message.
[ 3.681188] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
The issue is occurs in following step:
probe_setup_port() -> fintek_8250_goto_highspeed()
It change clocksource from 115200 to 921600 with wrong time, it should change
clocksource in set_termios() not in probed. The following 3 patches are
implemented change clocksource in fintek_8250_set_termios().
Commit 58178914ae ("serial: 8250_fintek: UART dynamic clocksource on Fintek F81216H")
Commit 195638b6d4 ("serial: 8250_fintek: UART dynamic clocksource on Fintek F81866")
Commit 423d9118c6 ("serial: 8250_fintek: Add F81966 Support")
Due to the high baud rate had implemented above 3 patches and the patch
Commit fab8a02b73 ("serial: 8250_fintek: Enable high speed mode on Fintek F81866")
is bugged, So this patch will remove it.
Fixes: fab8a02b73 ("serial: 8250_fintek: Enable high speed mode on Fintek F81866")
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Link: https://lore.kernel.org/r/20211215075835.2072-1-hpeter+linux_kernel@gmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit edaa26334c upstream.
The donation calculation logic assumes that the donor has non-zero
after-donation hweight, so the lowest active hweight a donating cgroup can
have is 2 so that it can donate 1 while keeping the other 1 for itself.
Earlier, we only donated from cgroups with sizable surpluses so this
condition was always true. However, with the precise donation algorithm
implemented, f1de2439ec ("blk-iocost: revamp donation amount
determination") made the donation amount calculation exact enabling even low
hweight cgroups to donate.
This means that in rare occasions, a cgroup with active hweight of 1 can
enter donation calculation triggering the following warning and then a
divide-by-zero oops.
WARNING: CPU: 4 PID: 0 at block/blk-iocost.c:1928 transfer_surpluses.cold+0x0/0x53 [884/94867]
...
RIP: 0010:transfer_surpluses.cold+0x0/0x53
Code: 92 ff 48 c7 c7 28 d1 ab b5 65 48 8b 34 25 00 ae 01 00 48 81 c6 90 06 00 00 e8 8b 3f fe ff 48 c7 c0 ea ff ff ff e9 95 ff 92 ff <0f> 0b 48 c7 c7 30 da ab b5 e8 71 3f fe ff 4c 89 e8 4d 85 ed 74 0
4
...
Call Trace:
<IRQ>
ioc_timer_fn+0x1043/0x1390
call_timer_fn+0xa1/0x2c0
__run_timers.part.0+0x1ec/0x2e0
run_timer_softirq+0x35/0x70
...
iocg: invalid donation weights in /a/b: active=1 donating=1 after=0
Fix it by excluding cgroups w/ active hweight < 2 from donating. Excluding
these extreme low hweight donations shouldn't affect work conservation in
any meaningful way.
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: f1de2439ec ("blk-iocost: revamp donation amount determination")
Cc: stable@vger.kernel.org # v5.10+
Link: https://lore.kernel.org/r/Ybfh86iSvpWKxhVM@slm.duckdns.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33fab97249 upstream.
When creating a subvolume, at create_subvol(), we allocate an anonymous
device and later call btrfs_get_new_fs_root(), which in turn just calls
btrfs_get_root_ref(). There we call btrfs_init_fs_root() which assigns
the anonymous device to the root, but if after that call there's an error,
when we jump to 'fail' label, we call btrfs_put_root(), which frees the
anonymous device and then returns an error that is propagated back to
create_subvol(). Than create_subvol() frees the anonymous device again.
When this happens, if the anonymous device was not reallocated after
the first time it was freed with btrfs_put_root(), we get a kernel
message like the following:
(...)
[13950.282466] BTRFS: error (device dm-0) in create_subvol:663: errno=-5 IO failure
[13950.283027] ida_free called for id=65 which is not allocated.
[13950.285974] BTRFS info (device dm-0): forced readonly
(...)
If the anonymous device gets reallocated by another btrfs filesystem
or any other kernel subsystem, then bad things can happen.
So fix this by setting the root's anonymous device to 0 at
btrfs_get_root_ref(), before we call btrfs_put_root(), if an error
happened.
Fixes: 2dfb1e43f5 ("btrfs: preallocate anon block device at first phase of snapshot creation")
CC: stable@vger.kernel.org # 5.10+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f35838a693 upstream.
Line 1169 (#3) allocates a memory chunk for victim_name by kmalloc(),
but when the function returns in line 1184 (#4) victim_name allocated
by line 1169 (#3) is not freed, which will lead to a memory leak.
There is a similar snippet of code in this function as allocating a memory
chunk for victim_name in line 1104 (#1) as well as releasing the memory
in line 1116 (#2).
We should kfree() victim_name when the return value of backref_in_log()
is less than zero and before the function returns in line 1184 (#4).
1057 static inline int __add_inode_ref(struct btrfs_trans_handle *trans,
1058 struct btrfs_root *root,
1059 struct btrfs_path *path,
1060 struct btrfs_root *log_root,
1061 struct btrfs_inode *dir,
1062 struct btrfs_inode *inode,
1063 u64 inode_objectid, u64 parent_objectid,
1064 u64 ref_index, char *name, int namelen,
1065 int *search_done)
1066 {
1104 victim_name = kmalloc(victim_name_len, GFP_NOFS);
// #1: kmalloc (victim_name-1)
1105 if (!victim_name)
1106 return -ENOMEM;
1112 ret = backref_in_log(log_root, &search_key,
1113 parent_objectid, victim_name,
1114 victim_name_len);
1115 if (ret < 0) {
1116 kfree(victim_name); // #2: kfree (victim_name-1)
1117 return ret;
1118 } else if (!ret) {
1169 victim_name = kmalloc(victim_name_len, GFP_NOFS);
// #3: kmalloc (victim_name-2)
1170 if (!victim_name)
1171 return -ENOMEM;
1180 ret = backref_in_log(log_root, &search_key,
1181 parent_objectid, victim_name,
1182 victim_name_len);
1183 if (ret < 0) {
1184 return ret; // #4: missing kfree (victim_name-2)
1185 } else if (!ret) {
1241 return 0;
1242 }
Fixes: d3316c8233 ("btrfs: Properly handle backref_in_log retval")
CC: stable@vger.kernel.org # 5.10+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Jianglei Nie <niejianglei2021@163.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 83b67041f3 upstream.
When generalising GPIO support and adding support for CP2102N, the GPIO
registration for some CP2105 devices accidentally broke. Specifically,
when all the pins of a port are in "modem" mode, and thus unavailable
for GPIO use, the GPIO chip would now be registered without having
initialised the number of GPIO lines. This would in turn be rejected by
gpiolib and some errors messages would be printed (but importantly probe
would still succeed).
Fix this by initialising the number of GPIO lines before registering the
GPIO chip.
Note that as for the other device types, and as when all CP2105 pins are
muxed for LED function, the GPIO chip is registered also when no pins
are available for GPIO use.
Reported-by: Maarten Brock <m.brock@vanmierlo.com>
Link: https://lore.kernel.org/r/5eb560c81d2ea1a2b4602a92d9f48a89@vanmierlo.com
Fixes: c8acfe0aad ("USB: serial: cp210x: implement GPIO support for CP2102N")
Cc: stable@vger.kernel.org # 4.19
Cc: Karoly Pados <pados@pados.hu>
Link: https://lore.kernel.org/r/20211126094348.31698-1-johan@kernel.org
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Maarten Brock <m.brock@vanmierlo.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 83dbf898a2 upstream.
Masking all unused MSI-X entries is done to ensure that a crash kernel
starts from a clean slate, which correponds to the reset state of the
device as defined in the PCI-E specificion 3.0 and later:
Vector Control for MSI-X Table Entries
--------------------------------------
"00: Mask bit: When this bit is set, the function is prohibited from
sending a message using this MSI-X Table entry.
...
This bit’s state after reset is 1 (entry is masked)."
A Marvell NVME device fails to deliver MSI interrupts after trying to
enable MSI-X interrupts due to that masking. It seems to take the MSI-X
mask bits into account even when MSI-X is disabled.
While not specification compliant, this can be cured by moving the masking
into the success path, so that the MSI-X table entries stay in device reset
state when the MSI-X setup fails.
[ tglx: Move it into the success path, add comment and amend changelog ]
Fixes: aa8092c1d1 ("PCI/MSI: Mask all unused MSI-X entries")
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-pci@vger.kernel.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211210161025.3287927-1-sr@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fac6bf87c5 upstream.
When activate_stm_id_vb_detection is enabled, ID and Vbus detection relies
on sensing comparators. This detection needs time to stabilize.
A delay was already applied in dwc2_resume() when reactivating the
detection, but it wasn't done in dwc2_probe().
This patch adds delay after enabling STM ID/VBUS detection. Then, ID state
is good when initializing gadget and host, and avoid to get a wrong
Connector ID Status Change interrupt.
Fixes: a415083a11 ("usb: dwc2: add support for STM32MP15 SoCs USB OTG HS and FS")
Cc: stable <stable@vger.kernel.org>
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211207124510.268841-1-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1aa2abb33a ]
The ability to write to MSR_IA32_PERF_CAPABILITIES from the host should
not depend on guest visible CPUID entries, even if just to allow
creating/restoring guest MSRs and CPUIDs in any sequence.
Fixes: 27461da310 ("KVM: x86/pmu: Support full width counting")
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20211216165213.338923-3-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f08adf5add ]
Szymon rightly pointed out that the previous check for the endpoint
direction in bRequestType was not looking at only the bit involved, but
rather the whole value. Normally this is ok, but for some request
types, bits other than bit 8 could be set and the check for the endpoint
length could not stall correctly.
Fix that up by only checking the single bit.
Fixes: 153a2d7e33 ("USB: gadget: detect too-big endpoint 0 requests")
Cc: Felipe Balbi <balbi@kernel.org>
Reported-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Link: https://lore.kernel.org/r/20211214184621.385828-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2fcbf81c3 ]
The libbpf CI reported occasional failure in btf_skc_cls_ingress:
test_syncookie:FAIL:Unexpected syncookie states gen_cookie:80326634 recv_cookie:0
bpf prog error at line 97
"error at line 97" means the bpf prog cannot find the listening socket
when the final ack is received. It then skipped processing
the syncookie in the final ack which then led to "recv_cookie:0".
The problem is the userspace program did not do accept() and went
ahead to close(listen_fd) before the kernel (and the bpf prog) had
a chance to process the final ack.
The fix is to add accept() call so that the userspace will wait for
the kernel to finish processing the final ack first before close()-ing
everything.
Fixes: 9a856cae22 ("bpf: selftest: Add test_btf_skc_cls_ingress")
Reported-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20211216191630.466151-1-kafai@fb.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b8e6e7824 ]
The descriptor list is a shared resource across all of the transmit queues, and
the locking mechanism used today only protects concurrency across a given
transmit queue between the transmit and reclaiming. This creates an opportunity
for the SYSTEMPORT hardware to work on corrupted descriptors if we have
multiple producers at once which is the case when using multiple transmit
queues.
This was particularly noticeable when using multiple flows/transmit queues and
it showed up in interesting ways in that UDP packets would get a correct UDP
header checksum being calculated over an incorrect packet length. Similarly TCP
packets would get an equally correct checksum computed by the hardware over an
incorrect packet length.
The SYSTEMPORT hardware maintains an internal descriptor list that it re-arranges
when the driver produces a new descriptor anytime it writes to the
WRITE_PORT_{HI,LO} registers, there is however some delay in the hardware to
re-organize its descriptors and it is possible that concurrent TX queues
eventually break this internal allocation scheme to the point where the
length/status part of the descriptor gets used for an incorrect data buffer.
The fix is to impose a global serialization for all TX queues in the short
section where we are writing to the WRITE_PORT_{HI,LO} registers which solves
the corruption even with multiple concurrent TX queues being used.
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211215202450.4086240-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c15b3123f ]
In nginx/wrk benchmark, there's a hung problem with high probability
on case likes that: (client will last several minutes to exit)
server: smc_run nginx
client: smc_run wrk -c 10000 -t 1 http://server
Client hangs with the following backtrace:
0 [ffffa7ce8Of3bbf8] __schedule at ffffffff9f9eOd5f
1 [ffffa7ce8Of3bc88] schedule at ffffffff9f9eløe6
2 [ffffa7ce8Of3bcaO] schedule_timeout at ffffffff9f9e3f3c
3 [ffffa7ce8Of3bd2O] wait_for_common at ffffffff9f9el9de
4 [ffffa7ce8Of3bd8O] __flush_work at ffffffff9fOfeOl3
5 [ffffa7ce8øf3bdfO] smc_release at ffffffffcO697d24 [smc]
6 [ffffa7ce8Of3be2O] __sock_release at ffffffff9f8O2e2d
7 [ffffa7ce8Of3be4ø] sock_close at ffffffff9f8ø2ebl
8 [ffffa7ce8øf3be48] __fput at ffffffff9f334f93
9 [ffffa7ce8Of3be78] task_work_run at ffffffff9flOlff5
10 [ffffa7ce8Of3beaO] do_exit at ffffffff9fOe5Ol2
11 [ffffa7ce8Of3bflO] do_group_exit at ffffffff9fOe592a
12 [ffffa7ce8Of3bf38] __x64_sys_exit_group at ffffffff9fOe5994
13 [ffffa7ce8Of3bf4O] do_syscall_64 at ffffffff9f9d4373
14 [ffffa7ce8Of3bfsO] entry_SYSCALL_64_after_hwframe at ffffffff9fa0007c
This issue dues to flush_work(), which is used to wait for
smc_connect_work() to finish in smc_release(). Once lots of
smc_connect_work() was pending or all executing work dangling,
smc_release() has to block until one worker comes to free, which
is equivalent to wait another smc_connnect_work() to finish.
In order to fix this, There are two changes:
1. For those idle smc_connect_work(), cancel it from the workqueue; for
executing smc_connect_work(), waiting for it to finish. For that
purpose, replace flush_work() with cancel_work_sync().
2. Since smc_connect() hold a reference for passive closing, if
smc_connect_work() has been cancelled, release the reference.
Fixes: 24ac3a08e6 ("net/smc: rebuild nonblocking connect")
Reported-by: Tony Lu <tonylu@linux.alibaba.com>
Tested-by: Dust Li <dust.li@linux.alibaba.com>
Reviewed-by: Dust Li <dust.li@linux.alibaba.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Link: https://lore.kernel.org/r/1639571361-101128-1-git-send-email-alibuda@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a03ef676a ]
When printing netdev features %pNF already takes care of the 0x prefix,
remove the explicit one.
Fixes: 6413139dfc ("skbuff: increase verbosity when dumping skb data")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 407ecd1bd7 ]
The return value of kmalloc() needs to be checked.
To avoid use in efx_nic_update_stats() in case of the failure of alloc.
Fixes: b593b6f1b4 ("sfc_ef100: statistics gathering")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 481221775d ]
Zero-initialize memory for new map's value in function nsim_bpf_map_alloc
since it may cause a potential kernel information leak issue, as follows:
1. nsim_bpf_map_alloc calls nsim_map_alloc_elem to allocate elements for
a new map.
2. nsim_map_alloc_elem uses kmalloc to allocate map's value, but doesn't
zero it.
3. A user application can use IOCTL BPF_MAP_LOOKUP_ELEM to get specific
element's information in the map.
4. The kernel function map_lookup_elem will call bpf_map_copy_value to get
the information allocated at step-2, then use copy_to_user to copy to the
user buffer.
This can only leak information for an array map.
Fixes: 395cacb5f1 ("netdevsim: bpf: support fake map offload")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Haimin Zhang <tcs.kernel@gmail.com>
Link: https://lore.kernel.org/r/20211215111530.72103-1-tcs.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf0a375055 ]
The MDIO bus speed must be initialized before talking to the PHY the first
time in order to avoid talking to it using a speed that the PHY doesn't
support.
This fixes HW initialization error -17 (IXGBE_ERR_PHY_ADDR_INVALID) on
Denverton CPUs (a.k.a. the Atom C3000 family) on ports with a 10Gb network
plugged in. On those devices, HLREG0[MDCSPD] resets to 1, which combined
with the 10Gb network results in a 24MHz MDIO speed, which is apparently
too fast for the connected PHY. PHY register reads over MDIO bus return
garbage, leading to initialization failure.
Reproduced with Linux kernel 4.19 and 5.15-rc7. Can be reproduced using
the following setup:
* Use an Atom C3000 family system with at least one X552 LAN on the SoC
* Disable PXE or other BIOS network initialization if possible
(the interface must not be initialized before Linux boots)
* Connect a live 10Gb Ethernet cable to an X550 port
* Power cycle (not reset, doesn't always work) the system and boot Linux
* Observe: ixgbe interfaces w/ 10GbE cables plugged in fail with error -17
Fixes: e84db72727 ("ixgbe: Introduce function to control MDIO speed")
Signed-off-by: Cyril Novikov <cnovikov@lynx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 271225fd57 ]
Commit a296d665ea ("ixgbe: Add ethtool support to enable 2.5 and 5.0
Gbps support") introduced suppression of the advertisement of NBASE-T
speeds by default, according to Todd Fujinaka to accommodate customers
with network switches which could not cope with advertised NBASE-T
speeds, as posted in the E1000-devel mailing list:
https://sourceforge.net/p/e1000/mailman/message/37106269/
However, the suppression was not documented at all, nor was how to
enable NBASE-T support.
Properly document the NBASE-T suppression and how to enable NBASE-T
support.
Fixes: a296d665ea ("ixgbe: Add ethtool support to enable 2.5 and 5.0 Gbps support")
Reported-by: Robert Schlabbach <robert_s@gmx.net>
Signed-off-by: Robert Schlabbach <robert_s@gmx.net>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0182d1f3fa ]
The LTR maximum value was incorrectly written using the scale from
the LTR minimum value. This would cause incorrect values to be sent,
in cases where the initial calculation lead to different min/max scales.
Fixes: 707abf0695 ("igc: Add initial LTR support")
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6d335a60d ]
In `igbvf_probe`, if register_netdev() fails, the program will go to
label err_hw_init, and then to label err_ioremap. In free_netdev() which
is just below label err_ioremap, there is `list_for_each_entry_safe` and
`netif_napi_del` which aims to delete all entries in `dev->napi_list`.
The program has added an entry `adapter->rx_ring->napi` which is added by
`netif_napi_add` in igbvf_alloc_queues(). However, adapter->rx_ring has
been freed below label err_hw_init. So this a UAF.
In terms of how to patch the problem, we can refer to igbvf_remove() and
delete the entry before `adapter->rx_ring`.
The KASAN logs are as follows:
[ 35.126075] BUG: KASAN: use-after-free in free_netdev+0x1fd/0x450
[ 35.127170] Read of size 8 at addr ffff88810126d990 by task modprobe/366
[ 35.128360]
[ 35.128643] CPU: 1 PID: 366 Comm: modprobe Not tainted 5.15.0-rc2+ #14
[ 35.129789] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014
[ 35.131749] Call Trace:
[ 35.132199] dump_stack_lvl+0x59/0x7b
[ 35.132865] print_address_description+0x7c/0x3b0
[ 35.133707] ? free_netdev+0x1fd/0x450
[ 35.134378] __kasan_report+0x160/0x1c0
[ 35.135063] ? free_netdev+0x1fd/0x450
[ 35.135738] kasan_report+0x4b/0x70
[ 35.136367] free_netdev+0x1fd/0x450
[ 35.137006] igbvf_probe+0x121d/0x1a10 [igbvf]
[ 35.137808] ? igbvf_vlan_rx_add_vid+0x100/0x100 [igbvf]
[ 35.138751] local_pci_probe+0x13c/0x1f0
[ 35.139461] pci_device_probe+0x37e/0x6c0
[ 35.165526]
[ 35.165806] Allocated by task 366:
[ 35.166414] ____kasan_kmalloc+0xc4/0xf0
[ 35.167117] foo_kmem_cache_alloc_trace+0x3c/0x50 [igbvf]
[ 35.168078] igbvf_probe+0x9c5/0x1a10 [igbvf]
[ 35.168866] local_pci_probe+0x13c/0x1f0
[ 35.169565] pci_device_probe+0x37e/0x6c0
[ 35.179713]
[ 35.179993] Freed by task 366:
[ 35.180539] kasan_set_track+0x4c/0x80
[ 35.181211] kasan_set_free_info+0x1f/0x40
[ 35.181942] ____kasan_slab_free+0x103/0x140
[ 35.182703] kfree+0xe3/0x250
[ 35.183239] igbvf_probe+0x1173/0x1a10 [igbvf]
[ 35.184040] local_pci_probe+0x13c/0x1f0
Fixes: d4e0fe01a3 (igbvf: add new driver to support 82576 virtual functions)
Reported-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Letu Ren <fantasquex@gmail.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 584af82154 ]
Move checking condition of VF MAC filter before clearing
or adding MAC filter to VF to prevent potential blackout caused
by removal of necessary and working VF's MAC filter.
Fixes: 1b8b062a99 ("igb: add VF trust infrastructure")
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a708376361 ]
A new warning in clang points out two instances where boolean
expressions are being used with a bitwise OR instead of logical OR:
drivers/soc/tegra/fuse/speedo-tegra20.c:72:9: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
reg = tegra_fuse_read_spare(i) |
^~~~~~~~~~~~~~~~~~~~~~~~~~
||
drivers/soc/tegra/fuse/speedo-tegra20.c:72:9: note: cast one or both operands to int to silence this warning
drivers/soc/tegra/fuse/speedo-tegra20.c:87:9: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
reg = tegra_fuse_read_spare(i) |
^~~~~~~~~~~~~~~~~~~~~~~~~~
||
drivers/soc/tegra/fuse/speedo-tegra20.c:87:9: note: cast one or both operands to int to silence this warning
2 warnings generated.
The motivation for the warning is that logical operations short circuit
while bitwise operations do not.
In this instance, tegra_fuse_read_spare() is not semantically returning
a boolean, it is returning a bit value. Use u32 for its return type so
that it can be used with either bitwise or boolean operators without any
warnings.
Fixes: 25cd5a3914 ("ARM: tegra: Add speedo-based process identification")
Link: https://github.com/ClangBuiltLinux/linux/issues/1488
Suggested-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6692b3b97 ]
The mptcp ULP extension relies on sk->sk_sock_kern being set correctly:
It prevents setsockopt(fd, IPPROTO_TCP, TCP_ULP, "mptcp", 6); from
working for plain tcp sockets (any userspace-exposed socket).
But in case of fallback, accept() can return a plain tcp sk.
In such case, sk is still tagged as 'kernel' and setsockopt will work.
This will crash the kernel, The subflow extension has a NULL ctx->conn
mptcp socket:
BUG: KASAN: null-ptr-deref in subflow_data_ready+0x181/0x2b0
Call Trace:
tcp_data_ready+0xf8/0x370
[..]
Fixes: cf7da0d66c ("mptcp: Create SUBFLOW socket for incoming connections")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa464957f7 ]
Memory is allocated for gpu_metrics_table in renoir_init_smc_tables(),
but not freed in int smu_v12_0_fini_smc_tables(). Free it!
Fixes: 95868b8576 ("drm/amd/powerplay: add Renoir support for gpu metrics export")
Signed-off-by: Lang Yu <lang.yu@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 166b6a46b7 ]
We need to return EOPNOTSUPP for the unsupported mpls action type when
setup the flow action.
In the original implement, we will return 0 for the unsupported mpls
action type, actually we do not setup it and the following actions
to the flow action entry.
Fixes: 9838b20a7f ("net: sched: take rtnl lock in tc_setup_flow_action()")
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71da1aec21 ]
The recent GRE selftests defined NUM_NETIFS=10. If the users copy
forwarding.config.sample to forwarding.config directly, they will get
error "Command line is not complete" when run the GRE tests, because
create_netif_veth() failed with no interface name defined.
Fix it by extending the NETIFS with p9 and p10.
Fixes: 2800f24854 ("selftests: forwarding: Test multipath hashing on inner IP pkts for GRE tunnel")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28a2686c18 ]
IPv6 allows binding a socket to a device then binding to an address
not on the device (__inet6_bind -> ipv6_chk_addr with strict flag
not set). Update the bind tests to reflect legacy behavior.
Fixes: 34d0302ab8 ("selftests: Add ipv6 address bind tests to fcnal-test")
Reported-by: Li Zhijian <lizhijian@fujitsu.com>
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f108ae445 ]
Commit referenced below added negative socket bind tests for VRF. The
socket binds should fail since the address to bind to is in a VRF yet
the socket is not bound to the VRF or a device within it. Update the
expected return code to check for 1 (bind failure) so the test passes
when the bind fails as expected. Add a 'show_hint' comment to explain
why the bind is expected to fail.
Fixes: 75b2b2b3db ("selftests: Add ipv4 address bind tests to fcnal-test")
Reported-by: Li Zhijian <lizhijian@fujitsu.com>
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e0147592b ]
Commit referenced below added configuration in the default VRF that
duplicates a VRF to check MD5 passwords are properly used and fail
when expected. That config should not be added all the time as it
can cause tests to pass that should not (by matching on default VRF
setup when it should not). Move the duplicate setup to a function
that is only called for the MD5 tests and add a cleanup function
to remove it after the MD5 tests.
Fixes: 5cad8bce26 ("fcnal-test: Add TCP MD5 tests for VRF")
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27cbf64a76 ]
Currently, the hns3_remove function firstly uninstall client instance,
and then uninstall acceletion engine device. The netdevice is freed in
client instance uninstall process, but acceletion engine device uninstall
process still use it to trace runtime information. This causes a use after
free problem.
So fixes it by check the instance register state to avoid use after free.
Fixes: d8355240cf ("net: hns3: add trace event support for PF/VF mailbox")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41967a37b8 ]
arch_kexec_apply_relocations_add currently ignores all errors returned
by arch_kexec_do_relocs. This means that every unknown relocation is
silently skipped causing unpredictable behavior while the relocated code
runs. Fix this by checking for errors and fail kexec_file_load if an
unknown relocation type is encountered.
The problem was found after gcc changed its behavior and used
R_390_PLT32DBL relocations for brasl instruction and relied on ld to
resolve the relocations in the final link in case direct calls are
possible. As the purgatory code is only linked partially (option -r)
ld didn't resolve the relocations leaving them for arch_kexec_do_relocs.
But arch_kexec_do_relocs doesn't know how to handle R_390_PLT32DBL
relocations so they were silently skipped. This ultimately caused an
endless loop in the purgatory as the brasl instructions kept branching
to itself.
Fixes: 71406883fd ("s390/kexec_file: Add kexec_file_load system call")
Reported-by: Tao Liu <ltao@redhat.com>
Signed-off-by: Philipp Rudo <prudo@redhat.com>
Link: https://lore.kernel.org/r/20211208130741.5821-3-prudo@redhat.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1db8f5fc2e ]
The VMADDR_CID_ANY flag used by a socket means that the socket isn't bound
to any specific CID. For example, a host vsock server may want to be bound
with VMADDR_CID_ANY, so that a guest vsock client can connect to the host
server with CID=VMADDR_CID_HOST (i.e. 2), and meanwhile, a host vsock
client can connect to the same local server with CID=VMADDR_CID_LOCAL
(i.e. 1).
The current implementation sets the destination socket's svm_cid to a
fixed CID value after the first client's connection, which isn't an
expected operation. For example, if the guest client first connects to the
host server, the server's svm_cid gets set to VMADDR_CID_HOST, then other
host clients won't be able to connect to the server anymore.
Reproduce steps:
1. Run the host server:
socat VSOCK-LISTEN:1234,fork -
2. Run a guest client to connect to the host server:
socat - VSOCK-CONNECT:2:1234
3. Run a host client to connect to the host server:
socat - VSOCK-CONNECT:1:1234
Without this patch, step 3. above fails to connect, and socat complains
"socat[1720] E connect(5, AF=40 cid:1 port:1234, 16): Connection
reset by peer".
With this patch, the above works well.
Fixes: c0cfa2d8a7 ("vsock: add multi-transports support")
Signed-off-by: Wei Wang <wei.w.wang@intel.com>
Link: https://lore.kernel.org/r/20211126011823.1760-1-wei.w.wang@intel.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ebd29f916 ]
At the moment, using the ARM32 multi_v7_defconfig always results in two
SoCs being exposed in sysfs. This is wrong, as far as I'm aware the
Qualcomm DragonBoard 410c does not actually make use of a i.MX SoC. :)
qcom-db410c:/sys/devices/soc0$ grep . *
family:Freescale i.MX
machine:Qualcomm Technologies, Inc. APQ 8016 SBC
revision:0.0
serial_number:0000000000000000
soc_id:Unknown
qcom-db410c:/sys/devices/soc1$ grep . *
family:Snapdragon
machine:APQ8016
...
This happens because imx_soc_device_init() registers the soc device
unconditionally, even when running on devices that do not make use of i.MX.
Arnd already reported this more than a year ago and even suggested a fix
similar to this commit, but for some reason it was never submitted.
Fix it by checking if the "__mxc_cpu_type" variable was actually
initialized by earlier platform code. On devices without i.MX it will
simply stay 0.
Cc: Peng Fan <peng.fan@nxp.com>
Fixes: d2199b3487 ("ARM: imx: use device_initcall for imx_soc_device_init")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/CAK8P3a0hxO1TmK6oOMQ70AHSWJnP_CAq57YMOutrxkSYNjFeuw@mail.gmail.com/
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54baf56eaa ]
Before commit fc0c209c14 ("clk: Allow parents to be specified without
string names") child clks couldn't find their parent until the parent
clk was added to a list in __clk_core_init(). After that commit, child
clks can reference their parent clks directly via a clk_hw pointer, or
they can lookup that clk_hw pointer via DT if the parent clk is
registered with an OF clk provider.
The common clk framework treats hw->core being non-NULL as "the clk is
registered" per the logic within clk_core_fill_parent_index():
parent = entry->hw->core;
/*
* We have a direct reference but it isn't registered yet?
* Orphan it and let clk_reparent() update the orphan status
* when the parent is registered.
*/
if (!parent)
Therefore we need to be extra careful to not set hw->core until the clk
is fully registered with the clk framework. Otherwise we can get into a
situation where a child finds a parent clk and we move the child clk off
the orphan list when the parent isn't actually registered, wrecking our
enable accounting and breaking critical clks.
Consider the following scenario:
CPU0 CPU1
---- ----
struct clk_hw clkBad;
struct clk_hw clkA;
clkA.init.parent_hws = { &clkBad };
clk_hw_register(&clkA) clk_hw_register(&clkBad)
... __clk_register()
hw->core = core
...
__clk_register()
__clk_core_init()
clk_prepare_lock()
__clk_init_parent()
clk_core_get_parent_by_index()
clk_core_fill_parent_index()
if (entry->hw) {
parent = entry->hw->core;
At this point, 'parent' points to clkBad even though clkBad hasn't been
fully registered yet. Ouch! A similar problem can happen if a clk
controller registers orphan clks that are referenced in the DT node of
another clk controller.
Let's fix all this by only setting the hw->core pointer underneath the
clk prepare lock in __clk_core_init(). This way we know that
clk_core_fill_parent_index() can't see hw->core be non-NULL until the
clk is fully registered.
Fixes: fc0c209c14 ("clk: Allow parents to be specified without string names")
Signed-off-by: Mike Tipton <quic_mdtipton@quicinc.com>
Link: https://lore.kernel.org/r/20211109043438.4639-1-quic_mdtipton@quicinc.com
[sboyd@kernel.org: Reword commit text, update comment]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee2a095d3b ]
The smatch static checker warned about an uninitialized symbol usage in
this function, in the case where ceph_mdsc_build_path returns an error.
It turns out that that case is harmless, but it just looks sketchy.
Initialize the variable at declaration time, and remove the unneeded
setting of it later.
Fixes: a33f6432b3 ("ceph: encode inodes' parent/d_name in cap reconnect message")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 973e524563 ]
opened_inodes is incremented twice when the same inode is opened twice
with O_RDONLY and O_WRONLY respectively.
To reproduce, run this python script, then check the metrics:
import os
for _ in range(10000):
fd_r = os.open('a', os.O_RDONLY)
fd_w = os.open('a', os.O_WRONLY)
os.close(fd_r)
os.close(fd_w)
Fixes: 1dd8d47081 ("ceph: metrics for opened files, pinned caps and opened inodes")
Signed-off-by: Hu Weiwen <sehuww@mail.scut.edu.cn>
Reviewed-by: Xiubo Li <xiubli@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f4b3ee3c85 upstream.
If the audit daemon were ever to get stuck in a stopped state the
kernel's kauditd_thread() could get blocked attempting to send audit
records to the userspace audit daemon. With the kernel thread
blocked it is possible that the audit queue could grow unbounded as
certain audit record generating events must be exempt from the queue
limits else the system enter a deadlock state.
This patch resolves this problem by lowering the kernel thread's
socket sending timeout from MAX_SCHEDULE_TIMEOUT to HZ/10 and tweaks
the kauditd_send_queue() function to better manage the various audit
queues when connection problems occur between the kernel and the
audit daemon. With this patch, the backlog may temporarily grow
beyond the defined limits when the audit daemon is stopped and the
system is under heavy audit pressure, but kauditd_thread() will
continue to make progress and drain the queues as it would for other
connection problems. For example, with the audit daemon put into a
stopped state and the system configured to audit every syscall it
was still possible to shutdown the system without a kernel panic,
deadlock, etc.; granted, the system was slow to shutdown but that is
to be expected given the extreme pressure of recording every syscall.
The timeout value of HZ/10 was chosen primarily through
experimentation and this developer's "gut feeling". There is likely
no one perfect value, but as this scenario is limited in scope (root
privileges would be needed to send SIGSTOP to the audit daemon), it
is likely not worth exposing this as a tunable at present. This can
always be done at a later date if it proves necessary.
Cc: stable@vger.kernel.org
Fixes: 5b52330bbf ("audit: fix auditd/kernel connection state tracking")
Reported-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Tested-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Reviewed-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 817fc978b5 upstream.
virtio_max_dma_size() returns the maximum DMA mapping size of the virtio
device by querying dma_max_mapping_size() for the device when the DMA
API is in use for the vring. Unfortunately, the device passed is
initialised by register_virtio_device() and does not inherit the DMA
configuration from its parent, resulting in SWIOTLB errors when bouncing
is enabled and the default 256K mapping limit (IO_TLB_SEGSIZE) is not
respected:
| virtio-pci 0000:00:01.0: swiotlb buffer is full (sz: 294912 bytes), total 1024 (slots), used 725 (slots)
Follow the pattern used elsewhere in the virtio_ring code when calling
into the DMA layer and pass the parent device to dma_max_mapping_size()
instead.
Cc: Marc Zyngier <maz@kernel.org>
Cc: Quentin Perret <qperret@google.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Signed-off-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20211201112018.25276-1-will@kernel.org
Acked-by: Jason Wang <jasowang@redhat.com>
Tested-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Fixes: e6d6dd6c87 ("virtio: Introduce virtio_max_dma_size()")
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e572ff80f0 upstream.
Make the bounds propagation in __reg_assign_32_into_64() slightly more
robust and readable by aligning it similarly as we did back in the
__reg_combine_64_into_32() counterpart. Meaning, only propagate or
pessimize them as a smin/smax pair.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3cf2b61eb0 upstream.
For the case where both s32_{min,max}_value bounds are positive, the
__reg_assign_32_into_64() directly propagates them to their 64 bit
counterparts, otherwise it pessimises them into [0,u32_max] universe and
tries to refine them later on by learning through the tnum as per comment
in mentioned function. However, that does not always happen, for example,
in mov32 operation we call zext_32_to_64(dst_reg) which invokes the
__reg_assign_32_into_64() as is without subsequent bounds update as
elsewhere thus no refinement based on tnum takes place.
Thus, not calling into the __update_reg_bounds() / __reg_deduce_bounds() /
__reg_bound_offset() triplet as we do, for example, in case of ALU ops via
adjust_scalar_min_max_vals(), will lead to more pessimistic bounds when
dumping the full register state:
Before fix:
0: (b4) w0 = -1
1: R0_w=invP4294967295
(id=0,imm=ffffffff,
smin_value=4294967295,smax_value=4294967295,
umin_value=4294967295,umax_value=4294967295,
var_off=(0xffffffff; 0x0),
s32_min_value=-1,s32_max_value=-1,
u32_min_value=-1,u32_max_value=-1)
1: (bc) w0 = w0
2: R0_w=invP4294967295
(id=0,imm=ffffffff,
smin_value=0,smax_value=4294967295,
umin_value=4294967295,umax_value=4294967295,
var_off=(0xffffffff; 0x0),
s32_min_value=-1,s32_max_value=-1,
u32_min_value=-1,u32_max_value=-1)
Technically, the smin_value=0 and smax_value=4294967295 bounds are not
incorrect, but given the register is still a constant, they break assumptions
about const scalars that smin_value == smax_value and umin_value == umax_value.
After fix:
0: (b4) w0 = -1
1: R0_w=invP4294967295
(id=0,imm=ffffffff,
smin_value=4294967295,smax_value=4294967295,
umin_value=4294967295,umax_value=4294967295,
var_off=(0xffffffff; 0x0),
s32_min_value=-1,s32_max_value=-1,
u32_min_value=-1,u32_max_value=-1)
1: (bc) w0 = w0
2: R0_w=invP4294967295
(id=0,imm=ffffffff,
smin_value=4294967295,smax_value=4294967295,
umin_value=4294967295,umax_value=4294967295,
var_off=(0xffffffff; 0x0),
s32_min_value=-1,s32_max_value=-1,
u32_min_value=-1,u32_max_value=-1)
Without the smin_value == smax_value and umin_value == umax_value invariant
being intact for const scalars, it is possible to leak out kernel pointers
from unprivileged user space if the latter is enabled. For example, when such
registers are involved in pointer arithmtics, then adjust_ptr_min_max_vals()
will taint the destination register into an unknown scalar, and the latter
can be exported and stored e.g. into a BPF map value.
Fixes: 3f50f132d8 ("bpf: Verifier, do explicit ALU32 bounds tracking")
Reported-by: Kuee K1r0a <liulin063@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1fe98f5690 upstream.
Sending them out on a different queue can cause a race condition where a
number of packets in the queue may be discarded by the receiver, because
the ADDBA request is sent too early.
This affects any driver with software A-MPDU setup which does not allocate
packet seqno in hardware on tx, regardless of whether iTXQ is used or not.
The only driver I've seen that explicitly deals with this issue internally
is mwl8k.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20211202124533.80388-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5f25e71e31 ]
This is not an unrecoverable situation. Users of kvm_read_guest_offset_cached
and kvm_write_guest_offset_cached must expect the read/write to fail, and
therefore it is possible to just return early with an error value.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 908fa88e42 ]
With the elevated 'KVM_CAP_MAX_VCPUS' value kvm_create_max_vcpus test
may hit RLIMIT_NOFILE limits:
# ./kvm_create_max_vcpus
KVM_CAP_MAX_VCPU_ID: 4096
KVM_CAP_MAX_VCPUS: 1024
Testing creating 1024 vCPUs, with IDs 0...1023.
/dev/kvm not available (errno: 24), skipping test
Adjust RLIMIT_NOFILE limits to make sure KVM_CAP_MAX_VCPUS fds can be
opened. Note, raising hard limit ('rlim_max') requires CAP_SYS_RESOURCE
capability which is generally not needed to run kvm selftests (but without
raising the limit the test is doomed to fail anyway).
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20211123135953.667434-1-vkuznets@redhat.com>
[Skip the test if the hard limit can be raised. - Paolo]
Reviewed-by: Sean Christopherson <seanjc@google.com>
Tested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 311a839a1a upstream.
Add documentation for the V4L2_CID_NOTIFY_GAINS control.
This control is required by sensors that need to know what colour
gains will be applied to pixels by downstream processing (such as by
an ISP), though the sensor does not apply these gains itself.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit a9c80593ff upstream.
We add a new control V4L2_CID_NOTIFY_GAINS which allows the sensor to
be notified what gains will be applied to the different colour
channels by subsequent processing (such as by an ISP), even though the
sensor will not apply any of these gains itself.
For Bayer sensors this will be an array control taking 4 values which
are the 4 gains arranged in the fixed order B, Gb, Gr and R,
irrespective of the exact Bayer order of the sensor itself. The use of
an array makes it straightforward to extend this control to non-Bayer
sensors (for example, sensors with an RGBW pattern) in future.
The units are in all cases linear with the default value indicating a
gain of exactly 1.0. For example, if the default value were reported as
128 then the value 192 would represent a gain of exactly 1.5.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This path actually occurs when audio is started during a hdmi mode set.
As the data will be written by vc4_hdmi_set_infoframes when packet RAM
is enabled again, don't treat as an error
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
In addition to the RGB444 output, the BCM2711 HDMI controller supports
the YUV444 and YUV422 output formats.
Let's add support for them in the driver, but still use RGB as the
preferred format.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Currently we take the max_bpc property as the bpc value and do not try
anything else.
However, what the other drivers seem to be doing is that they would try
with the highest bpc allowed by the max_bpc property and the hardware
capabilities, test if it results in an acceptable configuration, and if
not decrease the bpc and try again.
Let's use the same logic.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The current code only base its decision for whether the scrambler must be
enabled or not on the pixel clock of the mode, but doesn't take the bits
per color into account.
Let's leverage the new function to compute the clock rate in the
scrambler setup code.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
In the function that validates that the clock isn't too high, we've only
taken our controller limitations into account so far.
However, the sink can have a limit on the maximum TMDS clock it can deal
with too which is exposed through the EDID and the drm_display_info.
Make sure we check it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The code to compute our clock rate for a given setup will be called in
multiple places in the next patches, so let's create a separate function
for it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Our code is doing the same clock rate validation in multiple instances.
Let's create a helper to share the rate validation.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
In order to support the YUV output, we'll need the atomic state to know
what is the state of the associated property in the CSC setup callback.
Let's change the prototype of that callback to allow us to access it.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The current CSC setup code for the BCM2711 uses a sequence of register
writes to configure the CSC depending on whether we output using a full
or limited range.
However, with the upcoming introduction of the YUV output, we're going
to add new matrices to perform the conversions, so we should switch to
something a bit more flexible that takes the matrix as an argument and
programs the CSC accordingly.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
On BCM2711, the HDMI_CSC_CTL register value has been hardcoded to an
opaque value. Let's replace it with properly defined values.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
On the BCM2711, the HDMI_VEC_INTERFACE_XBAR register configuration
depends on whether we're using an RGB or YUV output. Let's move that
configuration to the CSC setup.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The CSC callbacks takes a boolean as an argument to tell whether we're
using the full range or limited range RGB.
However, with the upcoming YUV support, the logic will be a bit more
complex. In order to address this, let's make the callbacks take the
entire mode, and call our new helper to tell whether the full or limited
range RGB should be used.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
We're going to need to tell whether we want to run with a full or
limited range RGB output in multiple places in the code, so let's create
a helper that will return whether we need with full range or not.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The drm_hdmi_avi_infoframe_colorspace() function actually sets the
colorimetry and extended_colorimetry fields in the hdmi_avi_infoframe
structure with DRM_MODE_COLORIMETRY_* values.
To make things worse, the hdmi_avi_infoframe structure also has a
colorspace field used to signal whether an RGB or YUV output is being
used.
Let's remove the inconsistency and allow for the colorspace usage by
renaming the function.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The current code, when parsing the EDID Deep Color depths, that the
YUV422 cannot be used, referring to the HDMI 1.3 Specification.
This specification, in its section 6.2.4, indeed states:
For each supported Deep Color mode, RGB 4:4:4 shall be supported and
optionally YCBCR 4:4:4 may be supported.
YCBCR 4:2:2 is not permitted for any Deep Color mode.
This indeed can be interpreted like the code does, but the HDMI 1.4
specification further clarifies that statement in its section 6.2.4:
For each supported Deep Color mode, RGB 4:4:4 shall be supported and
optionally YCBCR 4:4:4 may be supported.
YCBCR 4:2:2 is also 36-bit mode but does not require the further use
of the Deep Color modes described in section 6.5.2 and 6.5.3.
This means that, even though YUV422 can be used with 12 bit per color,
it shouldn't be treated as a deep color mode.
This deviates from the interpretation of the code and comment, so let's
fix those.
Fixes: d0c94692e0 ("drm/edid: Parse and handle HDMI deep color modes.")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
[ Upstream commit a4d5613c4d ]
When unused memory map is freed the preserved part of the memory map is
extended to match pageblock boundaries because lots of core mm
functionality relies on homogeneity of the memory map within pageblock
boundaries.
Since pfn_valid() is used to check whether there is a valid memory map
entry for a PFN, make it return true also for PFNs that have memory map
entries even if there is no actual memory populated there.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Tested-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/lkml/20210630071211.21011-1-rppt@kernel.org/
Signed-off-by: Mark-PK Tsai <mark-pk.tsai@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f921f53e08 ]
When CONFIG_SPARSEMEM=y the ranges of the memory map that are freed are not
aligned to the pageblock boundaries which breaks assumptions about
homogeneity of the memory map throughout core mm code.
Make sure that the freed memory map is always aligned on pageblock
boundaries regardless of the memory model selection.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/lkml/20210630071211.21011-1-rppt@kernel.org/
[backport upstream modification in mm/memblock.c to arch/arm/mm/init.c]
Signed-off-by: Mark-PK Tsai <mark-pk.tsai@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e2a86800d5 ]
The code that frees unused memory map uses rounds start and end of the
holes that are freed to MAX_ORDER_NR_PAGES to preserve continuity of the
memory map for MAX_ORDER regions.
Lots of core memory management functionality relies on homogeneity of the
memory map within each pageblock which size may differ from MAX_ORDER in
certain configurations.
Although currently, for the architectures that use free_unused_memmap(),
pageblock_order and MAX_ORDER are equivalent, it is cleaner to have common
notation thought mm code.
Replace MAX_ORDER_NR_PAGES with pageblock_nr_pages and update the comments
to make it more clear why the alignment to pageblock boundaries is
required.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/lkml/20210630071211.21011-1-rppt@kernel.org/
[backport upstream modification in mm/memblock.c to arch/arm/mm/init.c]
Signed-off-by: Mark-PK Tsai <mark-pk.tsai@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c29d979260 upstream.
The space allowed for new attributes can be too small if existing header
information is large. That can happen, for example, if there are very
many CPUs, due to having an event ID per CPU per event being stored in the
header information.
Fix by adding the existing header.data_offset. Also increase the extra
space allowed to 8KiB and align to a 4KiB boundary for neatness.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lore.kernel.org/lkml/20211125071457.2066863-1-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
[Adrian: Backport to v5.10]
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dde91ccfa2 upstream.
There is a short period between a net device starts to be unregistered
and when it is actually gone. In that time frame ethtool operations
could still be performed, which might end up in unwanted or undefined
behaviours[1].
Do not allow ethtool operations after a net device starts its
unregistration. This patch targets the netlink part as the ioctl one
isn't affected: the reference to the net device is taken and the
operation is executed within an rtnl lock section and the net device
won't be found after unregister.
[1] For example adding Tx queues after unregister ends up in NULL
pointer exceptions and UaFs, such as:
BUG: KASAN: use-after-free in kobject_get+0x14/0x90
Read of size 1 at addr ffff88801961248c by task ethtool/755
CPU: 0 PID: 755 Comm: ethtool Not tainted 5.15.0-rc6+ #778
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-4.fc34 04/014
Call Trace:
dump_stack_lvl+0x57/0x72
print_address_description.constprop.0+0x1f/0x140
kasan_report.cold+0x7f/0x11b
kobject_get+0x14/0x90
kobject_add_internal+0x3d1/0x450
kobject_init_and_add+0xba/0xf0
netdev_queue_update_kobjects+0xcf/0x200
netif_set_real_num_tx_queues+0xb4/0x310
veth_set_channels+0x1c3/0x550
ethnl_set_channels+0x524/0x610
Fixes: 041b1c5d4a ("ethtool: helper functions for netlink interface")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/20211203101318.435618-1-atenart@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dbd3e6eaf3 upstream.
The removal function is called regardless of whether
/proc/i8k was created successfully or not, the later
causing a WARN() on module removal.
Fix that by only registering the removal function
if /proc/i8k was created successfully.
Tested on a Inspiron 3505.
Fixes: 039ae58503 ("hwmon: Allow to compile dell-smm-hwmon driver without /proc/i8k")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Acked-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20211112171440.59006-1-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c791fe1e2 upstream.
In writeback cache mode mtime/ctime updates are cached, and flushed to the
server using the ->write_inode() callback.
Closing the file will result in a dirty inode being immediately written,
but in other cases the inode can remain dirty after all references are
dropped. This result in the inode being written back from reclaim, which
can deadlock on a regular allocation while the request is being served.
The usual mechanisms (GFP_NOFS/PF_MEMALLOC*) don't work for FUSE, because
serving a request involves unrelated userspace process(es).
Instead do the same as for dirty pages: make sure the inode is written
before the last reference is gone.
- fallocate(2)/copy_file_range(2): these call file_update_time() or
file_modified(), so flush the inode before returning from the call
- unlink(2), link(2) and rename(2): these call fuse_update_ctime(), so
flush the ctime directly from this helper
Reported-by: chenguanyou <chenguanyou@xiaomi.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Cc: Ed Tsai <ed.tsai@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7dd5d437c2 upstream.
In 32-bit architecture, the result of sizeof() is a 32-bit integer so
the expression becomes the multiplication between 2 32-bit integer which
can potentially leads to integer overflow. As a result,
bpf_map_area_alloc() allocates less memory than needed.
Fix this by casting 1 operand to u64.
Fixes: 0d2c4f9640 ("bpf: Eliminate rlimit-based memory accounting for sockmap and sockhash maps")
Fixes: 99c51064fb ("devmap: Use bpf_map_area_alloc() for allocating hash buckets")
Fixes: 546ac1ffb7 ("bpf: add devmap, a map for storing net device references")
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210613143440.71975-1-minhquangbui99@gmail.com
Signed-off-by: Connor O'Brien <connoro@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d445aa402d upstream.
Commit 723de0f917 ("staging: most: remove device from interface
structure") moved registration of driver-provided struct device to
the most subsystem. This updated dim2 driver as well.
However, struct device passed to register_device() becomes refcounted,
and must not be explicitly deallocated, but must provide release method
instead. Which is incompatible with managing it via devres.
This patch makes the device structure allocated without devres, adds
device release method, and moves device destruction there.
Fixes: 723de0f917 ("staging: most: remove device from interface structure")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Link: https://lore.kernel.org/r/20211005143448.8660-2-nikita.yoush@cogentembedded.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3244867af8 upstream.
Do not bail early if there are no bits set in the sparse banks for a
non-sparse, a.k.a. "all CPUs", IPI request. Per the Hyper-V spec, it is
legal to have a variable length of '0', e.g. VP_SET's BankContents in
this case, if the request can be serviced without the extra info.
It is possible that for a given invocation of a hypercall that does
accept variable sized input headers that all the header input fits
entirely within the fixed size header. In such cases the variable sized
input header is zero-sized and the corresponding bits in the hypercall
input should be set to zero.
Bailing early results in KVM failing to send IPIs to all CPUs as expected
by the guest.
Fixes: 214ff83d44 ("KVM: x86: hyperv: implement PV IPI send hypercalls")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20211207220926.718794-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5ceaebcda9 ]
[WHY]
It seems like after a series of plug/unplugs we end up in a situation
where tiled display doesnt support Audio.
[HOW]
The issue seems to be related to when we check streams changed after an
HPD, we should be checking the audio_struct as well to see if any of its
values changed.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Mustapha Ghaddar <mustapha.ghaddar@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02fe0fbd8a ]
In a typical read transfer, start completion flag is being set after
read finishes (notice ipd bit 4 being set):
trasnfer poll=0
i2c start
rk3x-i2c fdd40000.i2c: IRQ: state 1, ipd: 10
i2c read
rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 1b
i2c stop
rk3x-i2c fdd40000.i2c: IRQ: state 4, ipd: 33
This causes I2C transfer being aborted in polled mode from a stop completion
handler:
trasnfer poll=1
i2c start
rk3x-i2c fdd40000.i2c: IRQ: state 1, ipd: 10
i2c read
rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 0
rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 1b
i2c stop
rk3x-i2c fdd40000.i2c: IRQ: state 4, ipd: 13
i2c stop
rk3x-i2c fdd40000.i2c: unexpected irq in STOP: 0x10
Clearing the START flag after read fixes the issue without any obvious
side effects.
This issue was dicovered on RK3566 when adding support for powering
off the RK817 PMIC.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Reviewed-by: John Keeping <john@metanate.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2191b1dfef ]
When link modes were initially added in commit 2c76267943
("net/mlx4_en: Use PTYS register to query ethtool settings") and
later updated for the new ethtool API in commit 3d8f7cc78d
("net: mlx4: use new ETHTOOL_G/SSETTINGS API") the only 1/10G non-baseT
link modes configured were 1000baseKX, 10000baseKX4 and 10000baseKR.
It looks like these got picked to represent other modes since nothing
better was available.
Switch to using more specific link modes added in commit 5711a98221
("net: ethtool: add support for 1000BaseX and missing 10G link modes").
Tested with MCX311A-XCAT connected via DAC.
Before:
% sudo ethtool enp3s0
Settings for enp3s0:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseKX/Full
10000baseKR/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: 1000baseKX/Full
10000baseKR/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 10000Mb/s
Duplex: Full
Auto-negotiation: off
Port: Direct Attach Copper
PHYAD: 0
Transceiver: internal
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000014 (20)
link ifdown
Link detected: yes
With this change:
% sudo ethtool enp3s0
Settings for enp3s0:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseX/Full
10000baseCR/Full
10000baseSR/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: 1000baseX/Full
10000baseCR/Full
10000baseSR/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 10000Mb/s
Duplex: Full
Auto-negotiation: off
Port: Direct Attach Copper
PHYAD: 0
Transceiver: internal
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000014 (20)
link ifdown
Link detected: yes
Tested-by: Michael Stapelberg <michael@stapelberg.ch>
Signed-off-by: Erik Ekman <erik@kryo.se>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e9679738a ]
Revert commit b4b844930f ("tty: serial: fsl_lpuart: drop earlycon entry
for i.MX8QXP"), because this breaks earlycon support on imx8qm/imx8qxp.
While it is true that for earlycon there is no difference between
i.MX8QXP and i.MX7ULP (for now at least), there are differences
regarding clocks and fixups for wakeup support. For that reason it was
deemed unacceptable to add the imx7ulp compatible to device tree in
order to get earlycon working again.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20211124073109.805088-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83bb2c1a01 ]
In order to be able to use primitives such as vcpu_mode_is_32bit(),
we need to synchronize the guest PSTATE. However, this is currently
done deep into the bowels of the world-switch code, and we do have
helpers evaluating this much earlier (__vgic_v3_perform_cpuif_access
and handle_aarch32_guest, for example).
Move the saving of the guest pstate into the early fixups, which
cures the first issue. The second one will be addressed separately.
Tested-by: Fuad Tabba <tabba@google.com>
Reviewed-by: Fuad Tabba <tabba@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
bcm2835_isp_remove is called on an initialisation failure, but at that
point the drvdata hasn't been set. This causes a crash when e.g. using
the cutdown firmware (gpu_mem=16).
Move platform_set_drvdata before the instance probing loop to avoid the
problem.
See: https://github.com/raspberrypi/linux/issues/4774
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
This reverts commit f814bfc5f4.
The commit caused media stalls with kodi and stateful
v4l2 video decode.
John is now using a different way of limiting latency
through stateful v4l2 so this is not required.
Change the maximum sample rate for the amplifier to
192KHz as given in the Infineon specification.
Signed-off-by: Joerg Schambacher <joerg@hifiberry.com>
Parameterise the overlays so that they can have an optional
cam0 parameter to switch to i2c_vc and csi0.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
CM4S follows CM1/3, so based on the documentation cameras/displays
connect to 0/1 and 28/29, not 0/1 and 44/45.
Likewise the camera regulator controls are independent as on CM1/3.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Not all implementations wire up the enable GPIO and may just tie
it to a supply rail.
Make it optional.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Fixing up shutdown GPIOs via overrides is ugly, and doesn't work
on eg CM4 where both cameras share the same shutdown GPIO.
The driver is now updated to use the regulator framework, so switch
to using that instead.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The driver supported using GPIOs to control the shutdown line,
but no regulator control.
Add regulator hooks.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Now that we have regulators and clocks defined in the base DT for
image sensors, switch the overlays to use them.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Unloading regulators through dynamic device tree doesn't work
as the regulators will unregister whilst clients are still
registered. Whilst the regulator framework does WARN when that
happens, the client putting the regulator then typically results
in a NULL dereference and badness.
Instead of creating regulators and clocks from the overlays,
create regulators and clocks for the sensors in the base DT.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The VL805 fetches up to 4 transfer TRBs at a time. TRB reads don't cross
a 64B boundary, and if a TRB is fetched and is not on a 64B boundary,
the read is sized up to the next 64B boundary.
However the VL805 implements a readahead prefetch for TRBs on a transfer
ring. This fetches the next 64B after any TRB read has happened. Near
the end of a ring segment, the prefetcher can read the first 64B of the
next page in physical memory and this is where the behaviour causes a
bug.
The controller does not tag reads with which endpoint they are for, so
if the start of the next page is a ring segment used by a victim
endpoint, and the victim endpoint is about to fetch TRBs from the start
of the segment, the victim endpoint will read from the prefetched data
and not perform a read to main memory. If the data is stale, the ring
cycle state bit may not be correct and the endpoint will silently halt.
Adjust trbs_per_seg for transfer rings allocated for this controller.
See https://github.com/raspberrypi/linux/issues/4685
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
In anticipation of adjusting the number of utilised TRBs in a ring
segment, add trbs_per_seg to struct xhci_ring and use this instead
of a compile-time define.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
commit 9b6164342e upstream.
This document was written a long time ago. Update it.
[1] Drop the version information
The range of the supported GCC versions are always changing. The
current minimal GCC version is 4.9, and commit 1e860048c5
("gcc-plugins: simplify GCC plugin-dev capability test") removed the
old code accordingly.
We do not need to mention specific version ranges like "all gcc versions
from 4.5 to 6.0" since we forget to update the documentation when we
raise the minimal compiler version.
[2] Drop the C compiler statements
Since commit 77342a02ff ("gcc-plugins: drop support for GCC <= 4.7")
the GCC plugin infrastructure only supports g++.
[3] Drop supported architectures
As of v5.11-rc4, the infrastructure supports more architectures;
arm, arm64, mips, powerpc, riscv, s390, um, and x86. (just grep
"select HAVE_GCC_PLUGINS") Again, we miss to update this document when a
new architecture is supported. Let's just say "only some architectures".
[4] Update the apt-get example
We are now discussing to bump the minimal version to GCC 5. The GCC 4.9
support will be removed sooner or later. Change the package example to
gcc-10-plugin-dev while we are here.
[5] Update the build target
Since commit ce2fd53a10 ("kbuild: descend into scripts/gcc-plugins/
via scripts/Makefile"), "make gcc-plugins" is not supported.
"make scripts" builds all the enabled plugins, including some other
tools.
[6] Update the steps for adding a new plugin
At first, all CONFIG options for GCC plugins were located in arch/Kconfig.
After commit 45332b1bdf ("gcc-plugins: split out Kconfig entries to
scripts/gcc-plugins/Kconfig"), scripts/gcc-plugins/Kconfig became the
central place to collect plugin CONFIG options. In my understanding,
this requirement no longer exists because commit 9f671e5815 ("security:
Create "kernel hardening" config area") moved some of plugin CONFIG
options to another file. Find an appropriate place to add the new CONFIG.
The sub-directory support was never used by anyone, and removed by
commit c17d6179ad ("gcc-plugins: remove unused GCC_PLUGIN_SUBDIR").
Remove the useless $(src)/ prefix.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f4c3b83b75 upstream.
With commit 1e860048c5 ("gcc-plugins: simplify GCC plugin-dev
capability test") applied, this hunk can be way simplified because
now scripts/gcc-plugins/Kconfig only checks plugin-version.h
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b560b21f71 upstream.
This commit adds BPF verifier selftests that cover all corner cases by
packet boundary checks. Specifically, 8-byte packet reads are tested at
the beginning of data and at the beginning of data_meta, using all kinds
of boundary checks (all comparison operators: <, >, <=, >=; both
permutations of operands: data + length compared to end, end compared to
data + length). For each case there are three tests:
1. Length is just enough for an 8-byte read. Length is either 7 or 8,
depending on the comparison.
2. Length is increased by 1 - should still pass the verifier. These
cases are useful, because they failed before commit 2fa7d94afc
("bpf: Fix the off-by-two error in range markings").
3. Length is decreased by 1 - should be rejected by the verifier.
Some existing tests are just renamed to avoid duplication.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20211207081521.41923-1-maximmi@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b383a42ca5 upstream.
INVALL CMD specifies that the ITS must ensure any caching associated with
the interrupt collection defined by ICID is consistent with the LPI
configuration tables held in memory for all Redistributors. SYNC is
required to ensure that INVALL is executed.
Currently, LPI configuration data may be inconsistent with that in the
memory within a short period of time after the INVALL command is executed.
Signed-off-by: Wudi Wang <wangwudi@hisilicon.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Fixes: cc2d3216f5 ("irqchip: GICv3: ITS command queue")
Link: https://lore.kernel.org/r/20211208015429.5007-1-zhangshaokun@hisilicon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0a553502e upstream.
irq-armada-370-xp driver already sets MSI_FLAG_MULTI_PCI_MSI flag into
msi_domain_info structure. But allocated interrupt numbers for Multi-MSI
needs to be properly aligned otherwise devices send MSI interrupt with
wrong number.
Fix this issue by using function bitmap_find_free_region() instead of
bitmap_find_next_zero_area() to allocate aligned interrupt numbers.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: a71b9412c9 ("irqchip/armada-370-xp: Allow allocation of multiple MSIs")
Cc: stable@vger.kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211125130057.26705-2-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6661146427 upstream.
IIO trigger handlers must call iio_trigger_notify_done() when done. This
must be done even when an error occurred. Otherwise the trigger will be
seen as busy indefinitely and the trigger handler will never be called
again.
The ad7768-1 driver neglects to call iio_trigger_notify_done() when there
is an error reading the converter data. Fix this by making sure that
iio_trigger_notify_done() is included in the error exit path.
Fixes: a5f8c7da3d ("iio: adc: Add AD7768-1 ADC basic support")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211101144055.13858-2-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92beafb76a upstream.
Both the charging and discharging currents on AXP22x are stored as
12-bit integers, in accordance with the datasheet.
It's also confirmed by vendor BSP (axp20x_adc.c:axp22_icharge_to_mA).
The scale factor of 0.5 is never mentioned in datasheet, nor in the
vendor source code. I think it was here to compensate for
erroneous addition bit in register width.
Tested on custom A40i+AXP221s board with external ammeter as
a reference.
Fixes: 0e34d5de96 ("iio: adc: add support for X-Powers AXP20X and AXP22X PMICs ADCs")
Signed-off-by: Evgeny Boger <boger@wirenboard.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20211116213746.264378-1-boger@wirenboard.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f711f28e71 upstream.
Some I/Os are connected to ADC input channels, when the corresponding bit
in PCSEL register are set on STM32H7 and STM32MP15. This is done in the
prepare routine of stm32-adc driver.
There are constraints here, as PCSEL shouldn't be set when VDDA supply
is disabled. Enabling/disabling of VDDA supply in done via stm32-adc-core
runtime PM routines (before/after ADC is enabled/disabled).
Currently, PCSEL remains set when disabling ADC. Later on, PM runtime
can disable the VDDA supply. This creates some conditions on I/Os that
can start to leak current.
So PCSEL needs to be cleared when disabling the ADC.
Fixes: 95e339b6e8 ("iio: adc: stm32: add support for STM32H7")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Reviewed-by: Olivier Moysan <olivier.moysan@foss.st.com>
Link: https://lore.kernel.org/r/1634905169-23762-1-git-send-email-fabrice.gasnier@foss.st.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67fe29583e upstream.
IIO trigger handlers must call iio_trigger_notify_done() when done. This
must be done even when an error occurred. Otherwise the trigger will be
seen as busy indefinitely and the trigger handler will never be called
again.
The itg3200 driver neglects to call iio_trigger_notify_done() when there is
an error reading the gyro data. Fix this by making sure that
iio_trigger_notify_done() is included in the error exit path.
Fixes: 9dbf091da0 ("iio: gyro: Add itg3200")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211101144055.13858-1-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45febe0d63 upstream.
IIO trigger handlers need to return one of the irqreturn_t values.
Returning an error code is not supported.
The kxsd9 interrupt handler returns an error code if reading the data
registers fails. In addition when exiting due to an error the trigger
handler does not call `iio_trigger_notify_done()`. Which when not done
keeps the triggered disabled forever.
Modify the code so that the function returns a valid irqreturn_t value as
well as calling `iio_trigger_notify_done()` on all exit paths.
Since we can't return the error code make sure to at least log it as part
of the error message.
Fixes: 0427a106a9 ("iio: accel: kxsd9: Add triggered buffer handling")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20211024171251.22896-2-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef9d67fa72 upstream.
IIO trigger handlers need to return one of the irqreturn_t values.
Returning an error code is not supported.
The ltr501 interrupt handler gets this right for most error paths, but
there is one case where it returns the error code.
In addition for this particular case the trigger handler does not call
`iio_trigger_notify_done()`. Which when not done keeps the triggered
disabled forever.
Modify the code so that the function returns a valid irqreturn_t value as
well as calling `iio_trigger_notify_done()` on all exit paths.
Fixes: 2690be9051 ("iio: Add Lite-On ltr501 ambient light / proximity sensor driver")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211024171251.22896-1-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd00822357 upstream.
The mma8452 driver directly assigns a trigger to the struct iio_dev. The
IIO core when done using this trigger will call `iio_trigger_put()` to drop
the reference count by 1.
Without the matching `iio_trigger_get()` in the driver the reference count
can reach 0 too early, the trigger gets freed while still in use and a
use-after-free occurs.
Fix this by getting a reference to the trigger before assigning it to the
IIO device.
Fixes: ae6d9ce056 ("iio: mma8452: Add support for interrupt driven triggers.")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211024092700.6844-1-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a827a49846 upstream.
In viio_trigger_alloc() device_initialize() is used to set the initial
reference count of the trigger to 1. Then another get_device() is called on
trigger. This sets the reference count to 2 before the trigger is returned.
iio_trigger_free(), which is the matching API to viio_trigger_alloc(),
calls put_device() which decreases the reference count by 1. But the second
reference count acquired in viio_trigger_alloc() is never dropped.
As a result the iio_trigger_release() function is never called and the
memory associated with the trigger is never freed.
Since there is no reason for the trigger to start its lifetime with two
reference counts just remove the extra get_device() in
viio_trigger_alloc().
Fixes: 5f9c035cae ("staging:iio:triggers. Add a reference get to the core for triggers.")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20211024092700.6844-2-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7faac1953e upstream.
Make xhci_disable_slot() synchronous, thus ensuring it, and
xhci_free_dev() calling it return after xHC controller completes
the disable slot command.
Otherwise the roothub and xHC host may runtime suspend, and clear the
command ring while the disable slot command is being processed.
This causes a command completion mismatch as the completion event can't
be mapped to the correct command.
Command ring gets out of sync and commands time out.
Driver finally assumes host is unresponsive and bails out.
usb 2-4: USB disconnect, device number 10
xhci_hcd 0000:00:0d.0: ERROR mismatched command completion event
...
xhci_hcd 0000:00:0d.0: xHCI host controller not responding, assume dead
xhci_hcd 0000:00:0d.0: HC died; cleaning up
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211210141735.1384209-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 811ae81320 upstream.
When the xHCI is quirked with XHCI_RESET_ON_RESUME, runtime resume
routine also resets the controller.
This is bad for USB drivers without reset_resume callback, because
there's no subsequent call of usb_dev_complete() ->
usb_resume_complete() to force rebinding the driver to the device. For
instance, btusb device stops working after xHCI controller is runtime
resumed, if the controlled is quirked with XHCI_RESET_ON_RESUME.
So always take XHCI_RESET_ON_RESUME into account to solve the issue.
Cc: <stable@vger.kernel.org>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211210141735.1384209-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 86ebbc11bb upstream.
Under some conditions, USB gadget devices can show allocated buffer
contents to a host. Fix this up by zero-allocating them so that any
extra data will all just be zeros.
Reported-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Tested-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 153a2d7e33 upstream.
Sometimes USB hosts can ask for buffers that are too large from endpoint
0, which should not be allowed. If this happens for OUT requests, stall
the endpoint, but for IN requests, trim the request size to the endpoint
buffer size.
Co-developed-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f6071e5e39 upstream.
Currently rp_filter tests in fib_tests.sh:fib_rp_filter_test() are
failing. ping sockets are bound to dummy1 using the "-I" option
(SO_BINDTODEVICE), but socket lookup is failing when receiving ping
replies, since the routing table thinks they belong to dummy0.
For example, suppose ping is using a SOCK_RAW socket for ICMP messages.
When receiving ping replies, in __raw_v4_lookup(), sk->sk_bound_dev_if
is 3 (dummy1), but dif (skb_rtable(skb)->rt_iif) says 2 (dummy0), so the
raw_sk_bound_dev_eq() check fails. Similar things happen in
ping_lookup() for SOCK_DGRAM sockets.
These tests used to pass due to a bug [1] in iputils, where "ping -I"
actually did not bind ICMP message sockets to device. The bug has been
fixed by iputils commit f455fee41c07 ("ping: also bind the ICMP socket
to the specific device") in 2016, which is why our rp_filter tests
started to fail. See [2] .
Fixing the tests while keeping everything in one netns turns out to be
nontrivial. Rework the tests and build the following topology:
┌─────────────────────────────┐ ┌─────────────────────────────┐
│ network namespace 1 (ns1) │ │ network namespace 2 (ns2) │
│ │ │ │
│ ┌────┐ ┌─────┐ │ │ ┌─────┐ ┌────┐ │
│ │ lo │<───>│veth1│<────────┼────┼─>│veth2│<──────────>│ lo │ │
│ └────┘ ├─────┴──────┐ │ │ ├─────┴──────┐ └────┘ │
│ │192.0.2.1/24│ │ │ │192.0.2.1/24│ │
│ └────────────┘ │ │ └────────────┘ │
└─────────────────────────────┘ └─────────────────────────────┘
Consider sending an ICMP_ECHO packet A in ns2. Both source and
destination IP addresses are 192.0.2.1, and we use strict mode rp_filter
in both ns1 and ns2:
1. A is routed to lo since its destination IP address is one of ns2's
local addresses (veth2);
2. A is redirected from lo's egress to veth2's egress using mirred;
3. A arrives at veth1's ingress in ns1;
4. A is redirected from veth1's ingress to lo's ingress, again, using
mirred;
5. In __fib_validate_source(), fib_info_nh_uses_dev() returns false,
since A was received on lo, but reverse path lookup says veth1;
6. However A is not dropped since we have relaxed this check for lo in
commit 66f8209547 ("fib: relax source validation check for loopback
packets");
Making sure A is not dropped here in this corner case is the whole point
of having this test.
7. As A reaches the ICMP layer, an ICMP_ECHOREPLY packet, B, is
generated;
8. Similarly, B is redirected from lo's egress to veth1's egress (in
ns1), then redirected once again from veth2's ingress to lo's
ingress (in ns2), using mirred.
Also test "ping 127.0.0.1" from ns2. It does not trigger the relaxed
check in __fib_validate_source(), but just to make sure the topology
works with loopback addresses.
Tested with ping from iputils 20210722-41-gf9fb573:
$ ./fib_tests.sh -t rp_filter
IPv4 rp_filter tests
TEST: rp_filter passes local packets [ OK ]
TEST: rp_filter passes loopback packets [ OK ]
[1] https://github.com/iputils/iputils/issues/55
[2] f455fee41c
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Fixes: adb701d6cf ("selftests: add a test case for rp_filter")
Reviewed-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Peilin Ye <peilin.ye@bytedance.com>
Acked-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20211201004720.6357-1-yepeilin.cs@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d17b9737c2 upstream.
The ql_wait_for_drvr_lock() fails and returns false, then this
function should return an error code instead of returning success.
The other problem is that the success path prints an error message
netdev_err(ndev, "Releasing driver lock\n"); Delete that and
re-order the code a little to make it more clear.
Fixes: 5a4faa8737 ("[PATCH] qla3xxx NIC driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211207082416.GA16110@kili
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5bd95d171 upstream.
Background:
We have a customer is running a Profinet stack on the 8MM which receives and
responds PNIO packets every 4ms and PNIO-CM packets every 40ms. However, from
time to time the received PNIO-CM package is "stock" and is only handled when
receiving a new PNIO-CM or DCERPC-Ping packet (tcpdump shows the PNIO-CM and
the DCERPC-Ping packet at the same time but the PNIO-CM HW timestamp is from
the expected 40 ms and not the 2s delay of the DCERPC-Ping).
After debugging, we noticed PNIO, PNIO-CM and DCERPC-Ping packets would
be handled by different RX queues.
The root cause should be driver ack all queues' interrupt when handle a
specific queue in fec_enet_rx_queue(). The blamed patch is introduced to
receive as much packets as possible once to avoid interrupt flooding.
But it's unreasonable to clear other queues'interrupt when handling one
queue, this patch tries to fix it.
Fixes: ed63f1dcd5 (net: fec: clear receive interrupts before processing a packet)
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Reported-by: Nicolas Diaz <nicolas.diaz@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20211206135457.15946-1-qiangqing.zhang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit badd7857f5 upstream.
There are two error paths which accidentally return success instead of
a negative error code.
Fixes: bbd2190ce9 ("Altera TSE: Add main and header file for Altera Ethernet Driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2be6d4d16a upstream.
Currently, due to the sequential use of min_t() and clamp_t() macros,
in cdc_ncm_check_tx_max(), if dwNtbOutMaxSize is not set, the logic
sets tx_max to 0. This is then used to allocate the data area of the
SKB requested later in cdc_ncm_fill_tx_frame().
This does not cause an issue presently because when memory is
allocated during initialisation phase of SKB creation, more memory
(512b) is allocated than is required for the SKB headers alone (320b),
leaving some space (512b - 320b = 192b) for CDC data (172b).
However, if more elements (for example 3 x u64 = [24b]) were added to
one of the SKB header structs, say 'struct skb_shared_info',
increasing its original size (320b [320b aligned]) to something larger
(344b [384b aligned]), then suddenly the CDC data (172b) no longer
fits in the spare SKB data area (512b - 384b = 128b).
Consequently the SKB bounds checking semantics fails and panics:
skbuff: skb_over_panic: text:ffffffff830a5b5f len:184 put:172 \
head:ffff888119227c00 data:ffff888119227c00 tail:0xb8 end:0x80 dev:<NULL>
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:110!
RIP: 0010:skb_panic+0x14f/0x160 net/core/skbuff.c:106
<snip>
Call Trace:
<IRQ>
skb_over_panic+0x2c/0x30 net/core/skbuff.c:115
skb_put+0x205/0x210 net/core/skbuff.c:1877
skb_put_zero include/linux/skbuff.h:2270 [inline]
cdc_ncm_ndp16 drivers/net/usb/cdc_ncm.c:1116 [inline]
cdc_ncm_fill_tx_frame+0x127f/0x3d50 drivers/net/usb/cdc_ncm.c:1293
cdc_ncm_tx_fixup+0x98/0xf0 drivers/net/usb/cdc_ncm.c:1514
By overriding the max value with the default CDC_NCM_NTB_MAX_SIZE_TX
when not offered through the system provided params, we ensure enough
data space is allocated to handle the CDC data, meaning no crash will
occur.
Cc: Oliver Neukum <oliver@neukum.org>
Fixes: 289507d336 ("net: cdc_ncm: use sysfs for rx/tx aggregation tuning")
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Link: https://lore.kernel.org/r/20211202143437.1411410-1-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d1d57debe upstream.
Since 66dfdff03d ("perf tools: Add Python 3 support") we don't use
the tools/build/feature/test-libpython-version.c version in any Makefile
feature check:
$ find tools/ -type f | xargs grep feature-libpython-version
$
The only place where this was used was removed in 66dfdff03d:
- ifneq ($(feature-libpython-version), 1)
- $(warning Python 3 is not yet supported; please set)
- $(warning PYTHON and/or PYTHON_CONFIG appropriately.)
- $(warning If you also have Python 2 installed, then)
- $(warning try something like:)
- $(warning $(and ,))
- $(warning $(and ,) make PYTHON=python2)
- $(warning $(and ,))
- $(warning Otherwise, disable Python support entirely:)
- $(warning $(and ,))
- $(warning $(and ,) make NO_LIBPYTHON=1)
- $(warning $(and ,))
- $(error $(and ,))
- else
- LDFLAGS += $(PYTHON_EMBED_LDFLAGS)
- EXTLIBS += $(PYTHON_EMBED_LIBADD)
- LANG_BINDINGS += $(obj-perf)python/perf.so
- $(call detected,CONFIG_LIBPYTHON)
- endif
And nowadays we either build with PYTHON=python3 or just install the
python3 devel packages and perf will build against it.
But the leftover feature-libpython-version check made the fast path
feature detection to break in all cases except when python2 devel files
were installed:
$ rpm -qa | grep python.*devel
python3-devel-3.9.7-1.fc34.x86_64
$ rm -rf /tmp/build/perf ; mkdir -p /tmp/build/perf ;
$ make -C tools/perf O=/tmp/build/perf install-bin
make: Entering directory '/var/home/acme/git/perf/tools/perf'
BUILD: Doing 'make -j32' parallel build
HOSTCC /tmp/build/perf/fixdep.o
<SNIP>
$ cat /tmp/build/perf/feature/test-all.make.output
In file included from test-all.c:18:
test-libpython-version.c:5:10: error: #error
5 | #error
| ^~~~~
$ ldd ~/bin/perf | grep python
libpython3.9.so.1.0 => /lib64/libpython3.9.so.1.0 (0x00007fda6dbcf000)
$
As python3 is the norm these days, fix this by just removing the unused
feature-libpython-version feature check, making the test-all fast path
to work with the common case.
With this:
$ rm -rf /tmp/build/perf ; mkdir -p /tmp/build/perf ;
$ make -C tools/perf O=/tmp/build/perf install-bin |& head
make: Entering directory '/var/home/acme/git/perf/tools/perf'
BUILD: Doing 'make -j32' parallel build
HOSTCC /tmp/build/perf/fixdep.o
HOSTLD /tmp/build/perf/fixdep-in.o
LINK /tmp/build/perf/fixdep
Auto-detecting system features:
... dwarf: [ on ]
... dwarf_getlocations: [ on ]
... glibc: [ on ]
$ ldd ~/bin/perf | grep python
libpython3.9.so.1.0 => /lib64/libpython3.9.so.1.0 (0x00007f58800b0000)
$ cat /tmp/build/perf/feature/test-all.make.output
$
Reviewed-by: James Clark <james.clark@arm.com>
Fixes: 66dfdff03d ("perf tools: Add Python 3 support")
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jaroslav Škarvada <jskarvad@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: https://lore.kernel.org/lkml/YaYmeeC6CS2b8OSz@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 96db48c9d7 upstream.
This binding was already documented in phy.txt, commit 252ae5330d
("Documentation: devicetree: Add PHY no lane swap binding"), but got
accidently removed during YAML conversion in commit d8704342c1
("dt-bindings: net: Add a YAML schemas for the generic PHY options").
Note: 'enet-phy-lane-no-swap' and the absence of 'enet-phy-lane-swap' are
not identical, as the former one disable this feature, while the latter
one doesn't change anything.
Fixes: d8704342c1 ("dt-bindings: net: Add a YAML schemas for the generic PHY options")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20211130082756.713919-1-alexander.stein@ew.tq-group.com
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6a631c0432 upstream.
The initial implementation of migrate_disable() for mainline was a
wrapper around preempt_disable(). RT kernels substituted this with
a real migrate disable implementation.
Later on mainline gained true migrate disable support, but the
documentation was not updated.
Update the documentation, remove the claims about migrate_disable()
mapping to preempt_disable() on non-PREEMPT_RT kernels.
Fixes: 74d862b682 ("sched: Make migrate_disable/enable() independent of RT")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20211127163200.10466-2-bigeasy@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39bd54d43b upstream.
This reverts commit 239edf686c.
239edf686c ("PCI: aardvark: Fix support for PCI_ROM_ADDRESS1 on emulated
bridge") added support for the Type 1 Expansion ROM BAR at config offset
0x38, based on the register being listed in the Marvell Armada A3720 spec.
But the spec doesn't document it at all for RC mode, and there is no ROM in
the SOC, so remove this emulation for now.
The PCI bridge which represents aardvark's PCIe Root Port has an Expansion
ROM Base Address register at offset 0x30, but its meaning is different than
PCI's Expansion ROM BAR register, although the layout is the same. (This
is why we thought it does the same thing.)
First: there is no ROM (or part of BootROM) in the A3720 SOC dedicated for
PCIe Root Port (or controller in RC mode) containing executable code that
would initialize the Root Port, suitable for execution in bootloader (this
is how Expansion ROM BAR is used on x86).
Second: in A3720 spec the register (address 0xD0070030) is not documented
at all for Root Complex mode, but similar to other BAR registers, it has an
"entangled partner" in register 0xD0075920, which does address translation
for the BAR in 0xD0070030:
- the BAR register sets the address from the view of PCIe bus
- the translation register sets the address from the view of the CPU
The other BAR registers also have this entangled partner, and they can be
used to:
- in RC mode: address-checking on the receive side of the RC (they can
define address ranges for memory accesses from remote Endpoints to the
RC)
- in Endpoint mode: allow the remote CPU to access memory on A3720
The Expansion ROM BAR has only the Endpoint part documented, but from the
similarities we think that it can also be used in RC mode in that way.
So either Expansion ROM BAR has different meaning (if the hypothesis above
is true), or we don't know it's meaning (since it is not documented for RC
mode).
Remove the register from the emulated bridge accessing functions.
[bhelgaas: summarize reason for removal (first paragraph)]
Fixes: 239edf686c ("PCI: aardvark: Fix support for PCI_ROM_ADDRESS1 on emulated bridge")
Link: https://lore.kernel.org/r/20211125160148.26029-3-kabel@kernel.org
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9472335eaa upstream.
Under certain circumstances, the timing settings calculated by
the FSMC NAND controller driver were inaccurate.
These settings led to incorrect data reads or fallback to
timing mode 0 depending on the NAND chip used.
The timing computation did not take into account the following
constraint given in SPEAr3xx reference manual:
twait >= tCEA - (tset * TCLK) + TOUTDEL + TINDEL
Enhance the timings calculation by taking into account this
additional constraint.
This change has no impact on slow timing modes such as mode 0.
Indeed, on mode 0, computed values are the same with and
without the patch.
NANDs which previously stayed in mode 0 because of fallback to
mode 0 can now work at higher speeds and NANDs which were not
working at all because of the corrupted data work at high
speeds without troubles.
Overall improvement on a Micron/MT29F1G08 (flash_speed tool):
mode0 mode3
eraseblock write speed 3220 KiB/s 4511 KiB/s
eraseblock read speed 4491 KiB/s 7529 KiB/s
Fixes: d9fb079571 ("mtd: nand: fsmc: add support for SDR timings")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211119150316.43080-5-herve.codina@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8aa55ab422 upstream.
After setting pre-set combined to 16 queues and reserving 16 queues by
tc qdisc, pre-set maximum combined queues returned to default value
after VF reset being 4 and this generated errors during removing tc.
Fixed by removing clear num_req_queues before reset VF.
Fixes: e284fc2804 (i40e: Add and delete cloud filter)
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Bindushree P <Bindushree.p@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61125b8be8 upstream.
Fix failed operation code appearing if handling messages from VF.
Implemented by waiting for VF appropriate state if request starts
handle while VF reset.
Without this patch the message handling request while VF is in
a reset state ends with error -5 (I40E_ERR_PARAM).
Fixes: 5c3c48ac6b ("i40e: implement virtual device interface")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b0969f8389 upstream.
When hns_roce_v2_destroy_qp() is called, the brief calling process of the
driver is as follows:
......
hns_roce_v2_destroy_qp
hns_roce_v2_qp_modify
hns_roce_cmd_mbox
hns_roce_qp_destroy
If hns_roce_cmd_mbox() detects that the hardware is being reset during the
execution of the hns_roce_cmd_mbox(), the driver will not be able to get
the return value from the hardware (the firmware cannot respond to the
driver's mailbox during the hardware reset phase).
The driver needs to wait for the hardware reset to complete before
continuing to execute hns_roce_qp_destroy(), otherwise it may happen that
the driver releases the resources but the hardware is still accessing. In
order to fix this problem, HNS RoCE needs to add a piece of code to wait
for the hardware reset to complete.
The original interface get_hw_reset_stat() is the instantaneous state of
the hardware reset, which cannot accurately reflect whether the hardware
reset is completed, so it needs to be replaced with the ae_dev_reset_cnt
interface.
The sign that the hardware reset is complete is that the return value of
the ae_dev_reset_cnt interface is greater than the original value
reset_cnt recorded by the driver.
Fixes: 6a04aed6af ("RDMA/hns: Fix the chip hanging caused by sending mailbox&CMQ during reset")
Link: https://lore.kernel.org/r/20211123142402.26936-1-liangwenpeng@huawei.com
Signed-off-by: Yangyang Li <liyangyang20@huawei.com>
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52414e27d6 upstream.
is_reset is used to indicate whether the hardware starts to reset. When
hns_roce_hw_v2_reset_notify_down() is called, the hardware has not yet
started to reset. If is_reset is set at this time, all mailbox operations
of resource destroy actions will be intercepted by driver. When the driver
cleans up resources, but the hardware is still accessed, the following
errors will appear:
arm-smmu-v3 arm-smmu-v3.2.auto: event 0x10 received:
arm-smmu-v3 arm-smmu-v3.2.auto: 0x0000350100000010
arm-smmu-v3 arm-smmu-v3.2.auto: 0x000002088000003f
arm-smmu-v3 arm-smmu-v3.2.auto: 0x00000000a50e0800
arm-smmu-v3 arm-smmu-v3.2.auto: 0x0000000000000000
arm-smmu-v3 arm-smmu-v3.2.auto: event 0x10 received:
arm-smmu-v3 arm-smmu-v3.2.auto: 0x0000350100000010
arm-smmu-v3 arm-smmu-v3.2.auto: 0x000002088000043e
arm-smmu-v3 arm-smmu-v3.2.auto: 0x00000000a50a0800
arm-smmu-v3 arm-smmu-v3.2.auto: 0x0000000000000000
arm-smmu-v3 arm-smmu-v3.2.auto: event 0x10 received:
arm-smmu-v3 arm-smmu-v3.2.auto: 0x0000350100000010
arm-smmu-v3 arm-smmu-v3.2.auto: 0x0000020880000436
arm-smmu-v3 arm-smmu-v3.2.auto: 0x00000000a50a0880
arm-smmu-v3 arm-smmu-v3.2.auto: 0x0000000000000000
arm-smmu-v3 arm-smmu-v3.2.auto: event 0x10 received:
arm-smmu-v3 arm-smmu-v3.2.auto: 0x0000350100000010
arm-smmu-v3 arm-smmu-v3.2.auto: 0x000002088000043a
arm-smmu-v3 arm-smmu-v3.2.auto: 0x00000000a50e0840
hns3 0000:35:00.0: INT status: CMDQ(0x0) HW errors(0x0) other(0x0)
arm-smmu-v3 arm-smmu-v3.2.auto: 0x0000000000000000
hns3 0000:35:00.0: received unknown or unhandled event of vector0
arm-smmu-v3 arm-smmu-v3.2.auto: event 0x10 received:
arm-smmu-v3 arm-smmu-v3.2.auto: 0x0000350100000010
{34}[Hardware Error]: Hardware error from APEI Generic Hardware Error Source: 7
is_reset will be set correctly in check_aedev_reset_status(), so the
setting in hns_roce_hw_v2_reset_notify_down() should be deleted.
Fixes: 726be12f5c ("RDMA/hns: Set reset flag when hw resetting")
Link: https://lore.kernel.org/r/20211123084809.37318-1-liangwenpeng@huawei.com
Signed-off-by: Yangyang Li <liyangyang20@huawei.com>
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23ba28616d upstream.
Currently each channel is added as list to dai channel list, however
there is danger of adding same channel to multiple dai channel list
which endups corrupting the other list where its already added.
This patch ensures that the channel is actually free before adding to
the dai channel list and also ensures that the channel is on the list
before deleting it.
This check was missing previously, and we did not hit this issue as
we were testing very simple usecases with sequence of amixer commands.
Fixes: a70d924575 ("ASoC: wcd934x: add capture dapm widgets")
Fixes: dd9eb19b56 ("ASoC: wcd934x: add playback dapm widgets")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20211130160507.22180-2-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4739d88ad8 upstream.
msm_routing_put_audio_mixer() can return incorrect value in various scenarios.
scenario 1:
amixer cset iface=MIXER,name='SLIMBUS_0_RX Audio Mixer MultiMedia1' 1
amixer cset iface=MIXER,name='SLIMBUS_0_RX Audio Mixer MultiMedia1' 0
return value is 0 instead of 1 eventhough value was changed
scenario 2:
amixer cset iface=MIXER,name='SLIMBUS_0_RX Audio Mixer MultiMedia1' 1
amixer cset iface=MIXER,name='SLIMBUS_0_RX Audio Mixer MultiMedia1' 1
return value is 1 instead of 0 eventhough the value was not changed
scenario 3:
amixer cset iface=MIXER,name='SLIMBUS_0_RX Audio Mixer MultiMedia1' 0
return value is 1 instead of 0 eventhough the value was not changed
Fix this by adding checks, so that change notifications are sent correctly.
Fixes: e3a33673e8 ("ASoC: qdsp6: q6routing: Add q6routing driver")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20211130163110.5628-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 444dd878e8 upstream.
The kerneldoc comment of pm_runtime_active() does not reflect the
behavior of the function, so update it accordingly.
Fixes: 403d2d116e ("PM: runtime: Add kerneldoc comments to multiple helpers")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e227b198a upstream.
Although it is unlikely that stack could transmit a non LSO
skb with length > MTU, however in some cases or environment such
occurrences actually resulted into firmware asserts due to packet
length being greater than the max supported by the device (~9700B).
This patch adds the safeguard for such odd cases to avoid firmware
asserts.
v2: Added "Fixes" tag with one of the initial driver commit
which enabled the TX traffic actually (as this was probably
day1 issue which was discovered recently by some customer
environment)
Fixes: a2ec6172d2 ("qede: Add support for link")
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Link: https://lore.kernel.org/r/20211203174413.13090-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7db0e0c819 upstream.
According to ZBC and SPC specifications, the unit of ALLOCATION LENGTH
field of REPORT ZONES command is byte. However, current scsi_debug
implementation handles it as number of zones to calculate buffer size to
report zones. When the ALLOCATION LENGTH has a large number, this results
in too large buffer size and causes memory allocation failure. Fix the
failure by handling ALLOCATION LENGTH as byte unit.
Link: https://lore.kernel.org/r/20211207010638.124280-1-shinichiro.kawasaki@wdc.com
Fixes: f0d1cf9378 ("scsi: scsi_debug: Add ZBC zone commands")
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6539262057 upstream.
Calling scsi_remove_host() before scsi_add_host() results in a crash:
BUG: kernel NULL pointer dereference, address: 0000000000000108
RIP: 0010:device_del+0x63/0x440
Call Trace:
device_unregister+0x17/0x60
scsi_remove_host+0xee/0x2a0
pm8001_pci_probe+0x6ef/0x1b90 [pm80xx]
local_pci_probe+0x3f/0x90
We cannot call scsi_remove_host() in pm8001_alloc() because scsi_add_host()
has not been called yet at that point in time.
Function call tree:
pm8001_pci_probe()
|
`- pm8001_pci_alloc()
| |
| `- pm8001_alloc()
| |
| `- scsi_remove_host()
|
`- scsi_add_host()
Link: https://lore.kernel.org/r/20211201041627.1592487-1-ipylypiv@google.com
Fixes: 05c6c029a4 ("scsi: pm80xx: Increase number of supported queues")
Reviewed-by: Vishakha Channapattan <vishakhavc@google.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 48b27b6b51 upstream.
As people have been asking to allow non-root processes to have access to
the tracefs directory, it was considered best to only allow groups to have
access to the directory, where it is easier to just set the tracefs file
system to a specific group (as other would be too dangerous), and that way
the admins could pick which processes would have access to tracefs.
Unfortunately, this broke tooling on Android that expected the other bit
to be set. For some special cases, for non-root tools to trace the system,
tracefs would be mounted and change the permissions of the top level
directory which gave access to all running tasks permission to the
tracing directory. Even though this would be dangerous to do in a
production environment, for testing environments this can be useful.
Now with the new changes to not allow other (which is still the proper
thing to do), it breaks the testing tooling. Now more code needs to be
loaded on the system to change ownership of the tracing directory.
The real solution is to have tracefs honor the gid=xxx option when
mounting. That is,
(tracing group tracing has value 1003)
mount -t tracefs -o gid=1003 tracefs /sys/kernel/tracing
should have it that all files in the tracing directory should be of the
given group.
Copy the logic from d_walk() from dcache.c and simplify it for the mount
case of tracefs if gid is set. All the files in tracefs will be walked and
their group will be set to the value passed in.
Link: https://lkml.kernel.org/r/20211207171729.2a54e1b3@gandalf.local.home
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-fsdevel@vger.kernel.org
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reported-by: Kalesh Singh <kaleshsingh@google.com>
Reported-by: Yabin Cui <yabinc@google.com>
Fixes: 49d67e4457 ("tracefs: Have tracefs directories not set OTH permission bits by default")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a50e659b2a upstream.
The registration of XDP queue information is incorrect because the
RX queue id we use is invalid. When port->id == 0 it appears to works
as expected yet it's no longer the case when port->id != 0.
The problem arised while using a recent kernel version on the
MACCHIATOBin. This board has several ports:
* eth0 and eth1 are 10Gbps interfaces ; both ports has port->id == 0;
* eth2 is a 1Gbps interface with port->id != 0.
Code from xdp-tutorial (more specifically advanced03-AF_XDP) was used
to test packet capture and injection on all these interfaces. The XDP
kernel was simplified to:
SEC("xdp_sock")
int xdp_sock_prog(struct xdp_md *ctx)
{
int index = ctx->rx_queue_index;
/* A set entry here means that the correspnding queue_id
* has an active AF_XDP socket bound to it. */
if (bpf_map_lookup_elem(&xsks_map, &index))
return bpf_redirect_map(&xsks_map, index, 0);
return XDP_PASS;
}
Starting the program using:
./af_xdp_user -d DEV
Gives the following result:
* eth0 : ok
* eth1 : ok
* eth2 : no capture, no injection
Investigating the issue shows that XDP rx queues for eth2 are wrong:
XDP expects their id to be in the range [0..3] but we found them to be
in the range [32..35].
Trying to force rx queue ids using:
./af_xdp_user -d eth2 -Q 32
fails as expected (we shall not have more than 4 queues).
When we register the XDP rx queue information (using
xdp_rxq_info_reg() in function mvpp2_rxq_init()) we tell it to use
rxq->id as the queue id. This value is computed as:
rxq->id = port->id * max_rxq_count + queue_id
where max_rxq_count depends on the device version. In the MACCHIATOBin
case, this value is 32, meaning that rx queues on eth2 are numbered
from 32 to 35 - there are four of them.
Clearly, this is not the per-port queue id that XDP is expecting:
it wants a value in the range [0..3]. It shall directly use queue_id
which is stored in rxq->logic_rxq -- so let's use that value instead.
rxq->id is left untouched ; its value is indeed valid but it should
not be used in this context.
This is consistent with the remaining part of the code in
mvpp2_rxq_init().
With this change, packet capture is working as expected on all the
MACCHIATOBin ports.
Fixes: b27db2274b ("mvpp2: use page_pool allocator")
Signed-off-by: Louis Amas <louis.amas@eho.link>
Signed-off-by: Emmanuel Deloget <emmanuel.deloget@eho.link>
Reviewed-by: Marcin Wojtas <mw@semihalf.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/r/20211207143423.916334-1-louis.amas@eho.link
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 50252e4b5e upstream.
signalfd_poll() and binder_poll() are special in that they use a
waitqueue whose lifetime is the current task, rather than the struct
file as is normally the case. This is okay for blocking polls, since a
blocking poll occurs within one task; however, non-blocking polls
require another solution. This solution is for the queue to be cleared
before it is freed, by sending a POLLFREE notification to all waiters.
Unfortunately, only eventpoll handles POLLFREE. A second type of
non-blocking poll, aio poll, was added in kernel v4.18, and it doesn't
handle POLLFREE. This allows a use-after-free to occur if a signalfd or
binder fd is polled with aio poll, and the waitqueue gets freed.
Fix this by making aio poll handle POLLFREE.
A patch by Ramji Jiyani <ramjiyani@google.com>
(https://lore.kernel.org/r/20211027011834.2497484-1-ramjiyani@google.com)
tried to do this by making aio_poll_wake() always complete the request
inline if POLLFREE is seen. However, that solution had two bugs.
First, it introduced a deadlock, as it unconditionally locked the aio
context while holding the waitqueue lock, which inverts the normal
locking order. Second, it didn't consider that POLLFREE notifications
are missed while the request has been temporarily de-queued.
The second problem was solved by my previous patch. This patch then
properly fixes the use-after-free by handling POLLFREE in a
deadlock-free way. It does this by taking advantage of the fact that
freeing of the waitqueue is RCU-delayed, similar to what eventpoll does.
Fixes: 2c14fa838c ("aio: implement IOCB_CMD_POLL")
Cc: <stable@vger.kernel.org> # v4.18+
Link: https://lore.kernel.org/r/20211209010455.42744-6-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 363bee27e2 upstream.
Currently, aio_poll_wake() will always remove the poll request from the
waitqueue. Then, if aio_poll_complete_work() sees that none of the
polled events are ready and the request isn't cancelled, it re-adds the
request to the waitqueue. (This can easily happen when polling a file
that doesn't pass an event mask when waking up its waitqueue.)
This is fundamentally broken for two reasons:
1. If a wakeup occurs between vfs_poll() and the request being
re-added to the waitqueue, it will be missed because the request
wasn't on the waitqueue at the time. Therefore, IOCB_CMD_POLL
might never complete even if the polled file is ready.
2. When the request isn't on the waitqueue, there is no way to be
notified that the waitqueue is being freed (which happens when its
lifetime is shorter than the struct file's). This is supposed to
happen via the waitqueue entries being woken up with POLLFREE.
Therefore, leave the requests on the waitqueue until they are actually
completed (or cancelled). To keep track of when aio_poll_complete_work
needs to be scheduled, use new fields in struct poll_iocb. Remove the
'done' field which is now redundant.
Note that this is consistent with how sys_poll() and eventpoll work;
their wakeup functions do *not* remove the waitqueue entries.
Fixes: 2c14fa838c ("aio: implement IOCB_CMD_POLL")
Cc: <stable@vger.kernel.org> # v4.18+
Link: https://lore.kernel.org/r/20211209010455.42744-5-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42288cb44c upstream.
Several ->poll() implementations are special in that they use a
waitqueue whose lifetime is the current task, rather than the struct
file as is normally the case. This is okay for blocking polls, since a
blocking poll occurs within one task; however, non-blocking polls
require another solution. This solution is for the queue to be cleared
before it is freed, using 'wake_up_poll(wq, EPOLLHUP | POLLFREE);'.
However, that has a bug: wake_up_poll() calls __wake_up() with
nr_exclusive=1. Therefore, if there are multiple "exclusive" waiters,
and the wakeup function for the first one returns a positive value, only
that one will be called. That's *not* what's needed for POLLFREE;
POLLFREE is special in that it really needs to wake up everyone.
Considering the three non-blocking poll systems:
- io_uring poll doesn't handle POLLFREE at all, so it is broken anyway.
- aio poll is unaffected, since it doesn't support exclusive waits.
However, that's fragile, as someone could add this feature later.
- epoll doesn't appear to be broken by this, since its wakeup function
returns 0 when it sees POLLFREE. But this is fragile.
Although there is a workaround (see epoll), it's better to define a
function which always sends POLLFREE to all waiters. Add such a
function. Also make it verify that the queue really becomes empty after
all waiters have been woken up.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211209010455.42744-2-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a66307d473 upstream.
The ASMedia 1092 has a configuration mode which will present a
dummy device; sadly the implementation falsely claims to provide
a device with 100M which doesn't actually exist.
So disable this device to avoid errors during boot.
Cc: stable@vger.kernel.org
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f58ac1adc7 upstream.
With the design of this driver, this condition is often triggered.
However, the counter that this interrupt indicates an overflow is never
read either, so overflowing is harmless.
On my system, when a CAN bus starts flapping up and down, this locks up
the whole system with lots of interrupts and printks.
Specifically, this interrupt indicates the CEL field of ECR has
overflowed. All reads of ECR mask out CEL.
Fixes: e0d1f4816f ("can: m_can: add Bosch M_CAN controller support")
Link: https://lore.kernel.org/all/20211129222628.7490-1-brian.silverman@bluerivertech.com
Cc: stable@vger.kernel.org
Signed-off-by: Brian Silverman <brian.silverman@bluerivertech.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b19926d4f3 upstream.
dma_fence_chain_find_seqno only ever returns the top fence in the
chain or an unsignalled fence. Hence if we request a seqno that
is already signalled it returns a NULL fence. Some callers are
not prepared to handle this, like the syncobj transfer functions
for example.
This behavior is "new" with timeline syncobj and it looks like
not all callers were updated. To fix this behavior make sure
that a successful drm_sync_find_fence always returns a non-NULL
fence.
v2: Move the fix to drm_syncobj_find_fence from the transfer
functions.
Fixes: ea569910cb ("drm/syncobj: add transition iotcls between binary and timeline v2")
Cc: stable@vger.kernel.org
Signed-off-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Reviewed-by: Christian König <christian.koenig@amd.com>
Acked-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211208023935.17018-1-bas@basnieuwenhuizen.nl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 548ec0805c upstream.
A delegation break could arrive as soon as we've called vfs_setlease. A
delegation break runs a callback which immediately (in
nfsd4_cb_recall_prepare) adds the delegation to del_recall_lru. If we
then exit nfs4_set_delegation without hashing the delegation, it will be
freed as soon as the callback is done with it, without ever being
removed from del_recall_lru.
Symptoms show up later as use-after-free or list corruption warnings,
usually in the laundromat thread.
I suspect aba2072f45 "nfsd: grant read delegations to clients holding
writes" made this bug easier to hit, but I looked as far back as v3.0
and it looks to me it already had the same problem. So I'm not sure
where the bug was introduced; it may have been there from the beginning.
Cc: stable@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 55df1ce0d4 upstream.
The superblock of version 1.0 doesn't get moved to the new position on a
device size change. This leads to a rdev without a superblock on a known
position, the raid can't be re-assembled.
The line was removed by mistake and is re-added by this patch.
Fixes: d9c0fa509e ("md: fix max sectors calculation for super 1.0")
Cc: stable@vger.kernel.org
Signed-off-by: Markus Hochholdinger <markus@hochholdinger.net>
Reviewed-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8289ed9f93 upstream.
I hit the BUG_ON() with generic/475 test case, and to my surprise, all
callers of btrfs_del_root_ref() are already aborting transaction, thus
there is not need for such BUG_ON(), just go to @out label and caller
will properly handle the error.
CC: stable@vger.kernel.org # 5.4+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2e3930529 upstream.
I got dmesg errors on generic/281 on our overnight fstests. Looking at
the history this happens occasionally, with errors like this
WARNING: CPU: 0 PID: 673217 at fs/btrfs/extent_io.c:6848 assert_eb_page_uptodate+0x3f/0x50
CPU: 0 PID: 673217 Comm: kworker/u4:13 Tainted: G W 5.16.0-rc2+ #469
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.13.0-2.fc32 04/01/2014
Workqueue: btrfs-cache btrfs_work_helper
RIP: 0010:assert_eb_page_uptodate+0x3f/0x50
RSP: 0018:ffffae598230bc60 EFLAGS: 00010246
RAX: 0017ffffc0002112 RBX: ffffebaec4100900 RCX: 0000000000001000
RDX: ffffebaec45733c7 RSI: ffffebaec4100900 RDI: ffff9fd98919f340
RBP: 0000000000000d56 R08: ffff9fd98e300000 R09: 0000000000000000
R10: 0001207370a91c50 R11: 0000000000000000 R12: 00000000000007b0
R13: ffff9fd98919f340 R14: 0000000001500000 R15: 0000000001cb0000
FS: 0000000000000000(0000) GS:ffff9fd9fbc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f549fcf8940 CR3: 0000000114908004 CR4: 0000000000370ef0
Call Trace:
extent_buffer_test_bit+0x3f/0x70
free_space_test_bit+0xa6/0xc0
load_free_space_tree+0x1d6/0x430
caching_thread+0x454/0x630
? rcu_read_lock_sched_held+0x12/0x60
? rcu_read_lock_sched_held+0x12/0x60
? rcu_read_lock_sched_held+0x12/0x60
? lock_release+0x1f0/0x2d0
btrfs_work_helper+0xf2/0x3e0
? lock_release+0x1f0/0x2d0
? finish_task_switch.isra.0+0xf9/0x3a0
process_one_work+0x270/0x5a0
worker_thread+0x55/0x3c0
? process_one_work+0x5a0/0x5a0
kthread+0x174/0x1a0
? set_kthread_struct+0x40/0x40
ret_from_fork+0x1f/0x30
This happens because we're trying to read from a extent buffer page that
is !PageUptodate. This happens because we will clear the page uptodate
when we have an IO error, but we don't clear the extent buffer uptodate.
If we do a read later and find this extent buffer we'll think its valid
and not return an error, and then trip over this warning.
Fix this by also clearing uptodate on the extent buffer when this
happens, so that we get an error when we do a btrfs_search_slot() and
find this block later.
CC: stable@vger.kernel.org # 5.4+
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 619764cc2e upstream.
This fixes the SND_PCI_QUIRK(...) of the TongFang PHxTxX1 barebone. This
fixes the issue of sound not working after s3 suspend.
When waking up from s3 suspend the Coef 0x10 is set to 0x0220 instead of
0x0020. Setting the value manually makes the sound work again. This patch
does this automatically.
While being on it, I also fixed the comment formatting of the quirk and
shortened variable and function names.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Fixes: dd6dd6e3c7 ("ALSA: hda/realtek: Add quirk for TongFang PHxTxX1")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211202165010.876431-1-wse@tuxedocomputers.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6409dd6bd upstream.
When control_compat.c:copy_ctl_value_to_user() is used, by
ctl_elem_read_user() & ctl_elem_write_user(), it must also copy back the
snd_ctl_elem_id value that may have been updated (filled in) by the call
to snd_ctl_elem_read/snd_ctl_elem_write().
This matches the functionality provided by snd_ctl_elem_read_user() and
snd_ctl_elem_write_user(), via snd_ctl_build_ioff().
Without this, and without making additional calls to snd_ctl_info()
which are unnecessary when using the non-compat calls, a userspace
application will not know the numid value for the element and
consequently will not be able to use the poll/read interface on the
control file to determine which elements have updates.
Signed-off-by: Alan Young <consult.awy@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211202150607.543389-1-consult.awy@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ebfaa11eb upstream.
Prior to commit 0baedd7927 ("KVM: x86: make Hyper-V PV TLB flush use
tlb_flush_guest()"), kvm_hv_flush_tlb() was using 'KVM_REQ_TLB_FLUSH |
KVM_REQUEST_NO_WAKEUP' when making a request to flush TLBs on other vCPUs
and KVM_REQ_TLB_FLUSH is/was defined as:
(0 | KVM_REQUEST_WAIT | KVM_REQUEST_NO_WAKEUP)
so KVM_REQUEST_WAIT was lost. Hyper-V TLFS, however, requires that
"This call guarantees that by the time control returns back to the
caller, the observable effects of all flushes on the specified virtual
processors have occurred." and without KVM_REQUEST_WAIT there's a small
chance that the vCPU making the TLB flush will resume running before
all IPIs get delivered to other vCPUs and a stale mapping can get read
there.
Fix the issue by adding KVM_REQUEST_WAIT flag to KVM_REQ_TLB_FLUSH_GUEST:
kvm_hv_flush_tlb() is the sole caller which uses it for
kvm_make_all_cpus_request()/kvm_make_vcpus_request_mask() where
KVM_REQUEST_WAIT makes a difference.
Cc: stable@kernel.org
Fixes: 0baedd7927 ("KVM: x86: make Hyper-V PV TLB flush use tlb_flush_guest()")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20211209102937.584397-1-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a1aa356dd upstream.
iavf_set_ringparams doesn't communicate to the user that
1. The user requested descriptor count is out of range. Instead it
just quietly sets descriptors to the "clamped" value and calls it
done. This makes it look an invalid value was successfully set as
the descriptor count when this isn't actually true.
2. The user provided descriptor count needs to be inflated for alignment
reasons.
This behavior is confusing. The ice driver has already addressed this
by rejecting invalid values for descriptor count and
messaging for alignment adjustments.
Do the same thing here by adding the error and info messages.
Fixes: fbb7ddfef2 ("i40evf: core ethtool functionality")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Michal Maloszewski <michal.maloszewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e4dcc1396 upstream.
If the PF experiences an FLR, the VF's MSI and MSI-X configuration will
be conveniently and silently removed in the process. When this happens,
reset recovery will appear to complete normally but no traffic will
pass. The netdev watchdog will helpfully notify everyone of this issue.
To prevent such public embarrassment, restore MSI configuration at every
reset. For normal resets, this will do no harm, but for VF resets
resulting from a PF FLR, this will keep the VF working.
Fixes: 5eae00c57f ("i40evf: main driver core")
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae68d93354 upstream.
When an IPv4 packet is received, the ip_rcv_core(...) sets the receiving
interface index into the IPv4 socket control block (v5.16-rc4,
net/ipv4/ip_input.c line 510):
IPCB(skb)->iif = skb->skb_iif;
If that IPv4 packet is meant to be encapsulated in an outer IPv6+SRH
header, the seg6_do_srh_encap(...) performs the required encapsulation.
In this case, the seg6_do_srh_encap function clears the IPv6 socket control
block (v5.16-rc4 net/ipv6/seg6_iptunnel.c line 163):
memset(IP6CB(skb), 0, sizeof(*IP6CB(skb)));
The memset(...) was introduced in commit ef489749aa ("ipv6: sr: clear
IP6CB(skb) on SRH ip4ip6 encapsulation") a long time ago (2019-01-29).
Since the IPv6 socket control block and the IPv4 socket control block share
the same memory area (skb->cb), the receiving interface index info is lost
(IP6CB(skb)->iif is set to zero).
As a side effect, that condition triggers a NULL pointer dereference if
commit 0857d6f8c7 ("ipv6: When forwarding count rx stats on the orig
netdev") is applied.
To fix that issue, we set the IP6CB(skb)->iif with the index of the
receiving interface once again.
Fixes: ef489749aa ("ipv6: sr: clear IP6CB(skb) on SRH ip4ip6 encapsulation")
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20211208195409.12169-1-andrea.mayer@uniroma2.it
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c56c96303e upstream.
In line 800 (#1), nfp_cpp_area_alloc() allocates and initializes a
CPP area structure. But in line 807 (#2), when the cache is allocated
failed, this CPP area structure is not freed, which will result in
memory leak.
We can fix it by freeing the CPP area when the cache is allocated
failed (#2).
792 int nfp_cpp_area_cache_add(struct nfp_cpp *cpp, size_t size)
793 {
794 struct nfp_cpp_area_cache *cache;
795 struct nfp_cpp_area *area;
800 area = nfp_cpp_area_alloc(cpp, NFP_CPP_ID(7, NFP_CPP_ACTION_RW, 0),
801 0, size);
// #1: allocates and initializes
802 if (!area)
803 return -ENOMEM;
805 cache = kzalloc(sizeof(*cache), GFP_KERNEL);
806 if (!cache)
807 return -ENOMEM; // #2: missing free
817 return 0;
818 }
Fixes: 4cb584e0ee ("nfp: add CPP access core")
Signed-off-by: Jianglei Nie <niejianglei2021@163.com>
Acked-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20211209061511.122535-1-niejianglei2021@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28dc1b86f8 upstream.
If the hardware is constantly receiving unicast or broadcast packets
during driver load, the device previously counted many GLV_RDPC (VSI
dropped packets) events during init. This causes confusing dropped
packet statistics during driver load. The dropped packets counter
incrementing does stop once the driver finishes loading.
Avoid this problem by baselining our statistics at the end of driver
open instead of the end of probe.
Fixes: cdedef59de ("ice: Configure VSIs for Tx/Rx")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2fa7d94afc upstream.
The first commit cited below attempts to fix the off-by-one error that
appeared in some comparisons with an open range. Due to this error,
arithmetically equivalent pieces of code could get different verdicts
from the verifier, for example (pseudocode):
// 1. Passes the verifier:
if (data + 8 > data_end)
return early
read *(u64 *)data, i.e. [data; data+7]
// 2. Rejected by the verifier (should still pass):
if (data + 7 >= data_end)
return early
read *(u64 *)data, i.e. [data; data+7]
The attempted fix, however, shifts the range by one in a wrong
direction, so the bug not only remains, but also such piece of code
starts failing in the verifier:
// 3. Rejected by the verifier, but the check is stricter than in #1.
if (data + 8 >= data_end)
return early
read *(u64 *)data, i.e. [data; data+7]
The change performed by that fix converted an off-by-one bug into
off-by-two. The second commit cited below added the BPF selftests
written to ensure than code chunks like #3 are rejected, however,
they should be accepted.
This commit fixes the off-by-two error by adjusting new_range in the
right direction and fixes the tests by changing the range into the
one that should actually fail.
Fixes: fb2a311a31 ("bpf: fix off by one for range markings with L{T, E} patterns")
Fixes: b37242c773 ("bpf: add test cases to bpf selftests to cover all access tests")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20211130181607.593149-1-maximmi@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f45b2974cc upstream.
The arch_prepare_bpf_dispatcher function does not have a prototype, and
yields the following warning when W=1 is enabled for the kernel build.
>> arch/x86/net/bpf_jit_comp.c:2188:5: warning: no previous \
prototype for 'arch_prepare_bpf_dispatcher' [-Wmissing-prototypes]
2188 | int arch_prepare_bpf_dispatcher(void *image, s64 *funcs, \
int num_funcs)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~
Remove the warning by adding a function declaration to include/linux/bpf.h.
Fixes: 75ccbef636 ("bpf: Introduce BPF dispatcher")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Björn Töpel <bjorn@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20211117125708.769168-1-bjorn@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d43b75fbc2 upstream.
After the below patch, the conntrack attached to skb is set to "notrack" in
the context of vrf device, for locally generated packets.
But this is true only when the default qdisc is set to the vrf device. When
changing the qdisc, notrack is not set anymore.
In fact, there is a shortcut in the vrf driver, when the default qdisc is
set, see commit dcdd43c41e ("net: vrf: performance improvements for
IPv4") for more details.
This patch ensures that the behavior is always the same, whatever the qdisc
is.
To demonstrate the difference, a new test is added in conntrack_vrf.sh.
Fixes: 8c9c296adf ("vrf: run conntrack only in context of lower/physdev for locally generated packets")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Florian Westphal <fw@strlen.de>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ff2fc0286 upstream.
Reserving memory using efi_mem_reserve() calls into the x86
efi_arch_mem_reserve() function. This function will insert a new EFI
memory descriptor into the EFI memory map representing the area of
memory to be reserved and marking it as EFI runtime memory. As part
of adding this new entry, a new EFI memory map is allocated and mapped.
The mapping is where a problem can occur. This new memory map is mapped
using early_memremap() and generally mapped encrypted, unless the new
memory for the mapping happens to come from an area of memory that is
marked as EFI_BOOT_SERVICES_DATA memory. In this case, the new memory will
be mapped unencrypted. However, during replacement of the old memory map,
efi_mem_type() is disabled, so the new memory map will now be long-term
mapped encrypted (in efi.memmap), resulting in the map containing invalid
data and causing the kernel boot to crash.
Since it is known that the area will be mapped encrypted going forward,
explicitly map the new memory map as encrypted using early_memremap_prot().
Cc: <stable@vger.kernel.org> # 4.14.x
Fixes: 8f716c9b5f ("x86/mm: Add support to access boot related data in the clear")
Link: https://lore.kernel.org/all/ebf1eb2940405438a09d51d121ec0d02c8755558.1634752931.git.thomas.lendacky@amd.com/
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
[ardb: incorporate Kconfig fix by Arnd]
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb12797ab1 upstream.
The CAN clock frequency is used when calculating the CAN bittiming
parameters. When wrong clock frequency is used, the device may end up
with wrong bittiming parameters, depending on user requested bittiming
parameters.
To avoid this, get the CAN clock frequency from the device. Various
existing Kvaser Leaf products use different CAN clocks.
Fixes: 080f40a6fa ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Link: https://lore.kernel.org/all/20211208152122.250852-2-extja@kvaser.com
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60a8b5a161 upstream.
This buffer is currently allocated in hfi1_init():
if (reinit)
ret = init_after_reset(dd);
else
ret = loadtime_init(dd);
if (ret)
goto done;
/* allocate dummy tail memory for all receive contexts */
dd->rcvhdrtail_dummy_kvaddr = dma_alloc_coherent(&dd->pcidev->dev,
sizeof(u64),
&dd->rcvhdrtail_dummy_dma,
GFP_KERNEL);
if (!dd->rcvhdrtail_dummy_kvaddr) {
dd_dev_err(dd, "cannot allocate dummy tail memory\n");
ret = -ENOMEM;
goto done;
}
The reinit triggered path will overwrite the old allocation and leak it.
Fix by moving the allocation to hfi1_alloc_devdata() and the deallocation
to hfi1_free_devdata().
Link: https://lore.kernel.org/r/20211129192008.101968.91302.stgit@awfm-01.cornelisnetworks.com
Cc: stable@vger.kernel.org
Fixes: 46b010d3ee ("staging/rdma/hfi1: Workaround to prevent corruption during packet delivery")
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7e945e228 upstream.
The sixth byte of packet data has to be looked up in the sixth group,
not in the seventh one, even if we load the bucket data into ymm6
(and not ymm5, for convenience of tracking stalls).
Without this fix, matching on a MAC address as first field of a set,
if 8-bit groups are selected (due to a small set size) would fail,
that is, the given MAC address would never match.
Reported-by: Nikita Yushchenko <nikita.yushchenko@virtuozzo.com>
Cc: <stable@vger.kernel.org> # 5.6.x
Fixes: 7400b06396 ("nft_set_pipapo: Introduce AVX2-based lookup implementation")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Tested-By: Nikita Yushchenko <nikita.yushchenko@virtuozzo.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9003fbe0f3 upstream.
Add a HID_QUIRK_NO_INIT_REPORTS quirk for the
Microsoft Surface 3 (non pro) type-cover.
Trying to init the reports seems to confuse the type-cover and
causes 2 issues:
1. Despite hid-multitouch sending the command to switch the
touchpad to multitouch mode, it keeps sending events on the
mouse emulation interface.
2. The touchpad completely stops sending events after a reboot.
Adding the HID_QUIRK_NO_INIT_REPORTS quirk fixes both issues.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67a5a68013 upstream.
Fedora Rawhide has started including gcc 11,and the g++ compiler
throws a wobbly when it hits scripts/gcc-plugins:
HOSTCXX scripts/gcc-plugins/latent_entropy_plugin.so
In file included from /usr/include/c++/11/type_traits:35,
from /usr/lib/gcc/x86_64-redhat-linux/11/plugin/include/system.h:244,
from /usr/lib/gcc/x86_64-redhat-linux/11/plugin/include/gcc-plugin.h:28,
from scripts/gcc-plugins/gcc-common.h:7,
from scripts/gcc-plugins/latent_entropy_plugin.c:78:
/usr/include/c++/11/bits/c++0x_warning.h:32:2: error: #error This file requires compiler and library support for the ISO
C++ 2011 standard. This support must be enabled with the -std=c++11 or -std=gnu++11 compiler options.
32 | #error This file requires compiler and library support \
In fact, it works just fine with c++11, which has been in gcc since 4.8,
and we now require 4.9 as a minimum.
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/82487.1609006918@turing-police
Cc: Thomas Lindroth <thomas.lindroth@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e860048c5 upstream.
Linus pointed out a third of the time in the Kconfig parse stage comes
from the single invocation of cc1plus in scripts/gcc-plugin.sh [1],
and directly testing plugin-version.h for existence cuts down the
overhead a lot. [2]
This commit takes one step further to kill the build test entirely.
The small piece of code was probably intended to test the C++ designated
initializer, which was not supported until C++20.
In fact, with -pedantic option given, both GCC and Clang emit a warning.
$ echo 'class test { public: int test; } test = { .test = 1 };' | g++ -x c++ -pedantic - -fsyntax-only
<stdin>:1:43: warning: C++ designated initializers only available with '-std=c++2a' or '-std=gnu++2a' [-Wpedantic]
$ echo 'class test { public: int test; } test = { .test = 1 };' | clang++ -x c++ -pedantic - -fsyntax-only
<stdin>:1:43: warning: designated initializers are a C++20 extension [-Wc++20-designator]
class test { public: int test; } test = { .test = 1 };
^
1 warning generated.
Otherwise, modern C++ compilers should be able to build the code, and
hopefully skipping this test should not make any practical problem.
Checking the existence of plugin-version.h is still needed to ensure
the plugin-dev package is installed. The test code is now small enough
to be embedded in scripts/gcc-plugins/Kconfig.
[1] https://lore.kernel.org/lkml/CAHk-=wjU4DCuwQ4pXshRbwDCUQB31ScaeuDo1tjoZ0_PjhLHzQ@mail.gmail.com/
[2] https://lore.kernel.org/lkml/CAHk-=whK0aQxs6Q5ijJmYF1n2ch8cVFSUzU5yUM_HOjig=+vnw@mail.gmail.com/
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20201203125700.161354-1-masahiroy@kernel.org
Cc: Thomas Lindroth <thomas.lindroth@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72ee48ee89 upstream.
Currently, the UVC function is activated when open on the corresponding
v4l2 device is called. On another open the activation of the function
fails since the deactivation counter in `usb_function_activate` equals
0. However the error is not returned to userspace since the open of the
v4l2 device is successful.
On a close the function is deactivated (since deactivation counter still
equals 0) and the video is disabled in `uvc_v4l2_release`, although the
UVC application potentially is streaming.
Move activation of UVC function to subscription on UVC_EVENT_SETUP
because there we can guarantee for a userspace application utilizing
UVC. Block subscription on UVC_EVENT_SETUP while another application
already is subscribed to it, indicated by `bool func_connected` in
`struct uvc_device`. Extend the `struct uvc_file_handle` with member
`bool is_uvc_app_handle` to tag it as the handle used by the userspace
UVC application.
With this a process is able to check capabilities of the v4l2 device
without deactivating the function for the actual UVC application.
Reviewed-By: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Thomas Haemmerle <thomas.haemmerle@wolfvision.net>
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Acked-by: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/20211003201355.24081-1-m.grzeschik@pengutronix.de
Cc: Dan Vacura <W36195@motorola.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5961060692 upstream.
When the TLS cipher suite uses CCM mode, including AES CCM and
SM4 CCM, the first byte of the B0 block is flags, and the real
IV starts from the second byte. The XOR operation of the IV and
rec_seq should be skip this byte, that is, add the iv_offset.
Fixes: f295b3ae9f ("net/tls: Add support of AES128-CCM based ciphers")
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Cc: Vakul Garg <vakul.garg@nxp.com>
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit afdb4a5b1d upstream.
In commit c8c3735997 ("parisc: Enhance detection of synchronous cr16
clocksources") I assumed that CPUs on the same physical core are syncronous.
While booting up the kernel on two different C8000 machines, one with a
dual-core PA8800 and one with a dual-core PA8900 CPU, this turned out to be
wrong. The symptom was that I saw a jump in the internal clocks printed to the
syslog and strange overall behaviour. On machines which have 4 cores (2
dual-cores) the problem isn't visible, because the current logic already marked
the cr16 clocksource unstable in this case.
This patch now marks the cr16 interval timers unstable if we have more than one
CPU in the system, and it fixes this issue.
Fixes: c8c3735997 ("parisc: Enhance detection of synchronous cr16 clocksources")
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org> # v5.15+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f85e04503f upstream.
Commit f45709df77 ("serial: 8250: Don't touch RTS modem control while
in rs485 mode") sought to prevent user space from interfering with rs485
communication by ignoring a TIOCMSET ioctl() which changes RTS polarity.
It did so in serial8250_do_set_mctrl(), which turns out to be too deep
in the call stack: When a uart_port is opened, RTS polarity is set by
the rs485-aware function uart_port_dtr_rts(). It calls down to
serial8250_do_set_mctrl() and that particular RTS polarity change should
*not* be ignored.
The user-visible result is that on 8250_omap ports which use rs485 with
inverse polarity (RTS bit in MCR register is 1 to receive, 0 to send),
a newly opened port initially sets up RTS for sending instead of
receiving. That's because omap_8250_startup() sets the cached value
up->mcr to 0 and omap_8250_restore_regs() subsequently writes it to the
MCR register. Due to the commit, serial8250_do_set_mctrl() preserves
that incorrect register value:
do_sys_openat2
do_filp_open
path_openat
vfs_open
do_dentry_open
chrdev_open
tty_open
uart_open
tty_port_open
uart_port_activate
uart_startup
uart_port_startup
serial8250_startup
omap_8250_startup # up->mcr = 0
uart_change_speed
serial8250_set_termios
omap_8250_set_termios
omap_8250_restore_regs
serial8250_out_MCR # up->mcr written
tty_port_block_til_ready
uart_dtr_rts
uart_port_dtr_rts
serial8250_set_mctrl
omap8250_set_mctrl
serial8250_do_set_mctrl # mcr[1] = 1 ignored
Fix by intercepting RTS changes from user space in uart_tiocmset()
instead.
Link: https://lore.kernel.org/linux-serial/20211027111644.1996921-1-baocheng.su@siemens.com/
Fixes: f45709df77 ("serial: 8250: Don't touch RTS modem control while in rs485 mode")
Cc: Chao Zeng <chao.zeng@siemens.com>
Cc: stable@vger.kernel.org # v5.7+
Reported-by: Su Bao Cheng <baocheng.su@siemens.com>
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Tested-by: Su Bao Cheng <baocheng.su@siemens.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/21170e622a1aaf842a50b32146008b5374b3dd1d.1637596432.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 00de977f9e upstream.
Commit 761ed4a945 ("tty: serial_core: convert uart_close to use
tty_port_close") converted serial core to use tty_port_close() but
failed to notice that the transmit buffer still needs to be freed on
final close.
Not freeing the transmit buffer means that the buffer is no longer
cleared on next open so that any ioctl() waiting for the buffer to drain
might wait indefinitely (e.g. on termios changes) or that stale data can
end up being transmitted in case tx is restarted.
Furthermore, the buffer of any port that has been opened would leak on
driver unbind.
Note that the port lock is held when clearing the buffer pointer due to
the ldisc race worked around by commit a5ba1d95e4 ("uart: fix race
between uart_put_char() and uart_shutdown()").
Also note that the tty-port shutdown() callback is not called for
console ports so it is not strictly necessary to free the buffer page
after releasing the lock (cf. d72402145a ("tty/serial: do not free
trasnmit buffer page under port lock")).
Link: https://lore.kernel.org/r/319321886d97c456203d5c6a576a5480d07c3478.1635781688.git.baruch@tkos.co.il
Fixes: 761ed4a945 ("tty: serial_core: convert uart_close to use tty_port_close")
Cc: stable@vger.kernel.org # 4.9
Cc: Rob Herring <robh@kernel.org>
Reported-by: Baruch Siach <baruch@tkos.co.il>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211108085431.12637-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b40de7469e upstream.
The current implementation uses 0 as lower limit for the baud rate
tolerance for tegra20 and tegra30 chips which causes isses on UART
initialization as soon as baud rate clock is lower than required even
when within the standard UART tolerance of +/- 4%.
This fix aligns the implementation with the initial commit description
of +/- 4% tolerance for tegra chips other than tegra186 and
tegra194.
Fixes: d781ec21ba ("serial: tegra: report clk rate errors")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Patrik John <patrik.john@u-blox.com>
Link: https://lore.kernel.org/r/sig.19614244f8.20211123132737.88341-1-patrik.john@u-blox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac442a077a upstream.
The document 'ACPI for Arm Components 1.0' defines the following
_HID mappings:
-'Prime cell UART (PL011)': ARMH0011
-'SBSA UART': ARMHB000
Use the sbsa-uart driver when a device is described with
the 'ARMHB000' _HID.
Note:
PL011 devices currently use the sbsa-uart driver instead of the
uart-pl011 driver. Indeed, PL011 devices are not bound to a clock
in ACPI. It is not possible to change their baudrate.
Cc: <stable@vger.kernel.org>
Signed-off-by: Pierre Gondois <Pierre.Gondois@arm.com>
Link: https://lore.kernel.org/r/20211109172248.19061-1-Pierre.Gondois@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7492ffc90f upstream.
The CONSOLE_POLLING mode is used for tools like k(g)db. In this kind of
setup, it is often sharing a serial device with the normal system console.
This is usually no problem because the polling helpers can consume input
values directly (when in kgdb context) and the normal Linux handlers can
only consume new input values after kgdb switched back.
This is not true anymore when RX DMA is enabled for UARTDM controllers.
Single input values can no longer be received correctly. Instead following
seems to happen:
* on 1. input, some old input is read (continuously)
* on 2. input, two old inputs are read (continuously)
* on 3. input, three old input values are read (continuously)
* on 4. input, 4 previous inputs are received
This repeats then for each group of 4 input values.
This behavior changes slightly depending on what state the controller was
when the first input was received. But this makes working with kgdb
basically impossible because control messages are always corrupted when
kgdboc tries to parse them.
RX DMA should therefore be off when CONSOLE_POLLING is enabled to avoid
these kind of problems. No such problem was noticed for TX DMA.
Fixes: 9969394501 ("tty: serial: msm: Add RX DMA support")
Cc: stable@vger.kernel.org
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Link: https://lore.kernel.org/r/20211113121050.7266-1-sven@narfation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51523ed1c2 upstream.
The trampoline_pgd only maps the 0xfffffff000000000-0xffffffffffffffff
range of kernel memory (with 4-level paging). This range contains the
kernel's text+data+bss mappings and the module mapping space but not the
direct mapping and the vmalloc area.
This is enough to get the application processors out of real-mode, but
for code that switches back to real-mode the trampoline_pgd is missing
important parts of the address space. For example, consider this code
from arch/x86/kernel/reboot.c, function machine_real_restart() for a
64-bit kernel:
#ifdef CONFIG_X86_32
load_cr3(initial_page_table);
#else
write_cr3(real_mode_header->trampoline_pgd);
/* Exiting long mode will fail if CR4.PCIDE is set. */
if (boot_cpu_has(X86_FEATURE_PCID))
cr4_clear_bits(X86_CR4_PCIDE);
#endif
/* Jump to the identity-mapped low memory code */
#ifdef CONFIG_X86_32
asm volatile("jmpl *%0" : :
"rm" (real_mode_header->machine_real_restart_asm),
"a" (type));
#else
asm volatile("ljmpl *%0" : :
"m" (real_mode_header->machine_real_restart_asm),
"D" (type));
#endif
The code switches to the trampoline_pgd, which unmaps the direct mapping
and also the kernel stack. The call to cr4_clear_bits() will find no
stack and crash the machine. The real_mode_header pointer below points
into the direct mapping, and dereferencing it also causes a crash.
The reason this does not crash always is only that kernel mappings are
global and the CR3 switch does not flush those mappings. But if theses
mappings are not in the TLB already, the above code will crash before it
can jump to the real-mode stub.
Extend the trampoline_pgd to contain all kernel mappings to prevent
these crashes and to make code which runs on this page-table more
robust.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20211202153226.22946-5-joro@8bytes.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b50db7095f upstream.
There are cases that the TSC clocksource is wrongly judged as unstable by
the clocksource watchdog mechanism which tries to validate the TSC against
HPET, PM_TIMER or jiffies. While there is hardly a general reliable way to
check the validity of a watchdog, Thomas Gleixner proposed [1]:
"I'm inclined to lift that requirement when the CPU has:
1) X86_FEATURE_CONSTANT_TSC
2) X86_FEATURE_NONSTOP_TSC
3) X86_FEATURE_NONSTOP_TSC_S3
4) X86_FEATURE_TSC_ADJUST
5) At max. 4 sockets
After two decades of horrors we're finally at a point where TSC seems
to be halfway reliable and less abused by BIOS tinkerers. TSC_ADJUST
was really key as we can now detect even small modifications reliably
and the important point is that we can cure them as well (not pretty
but better than all other options)."
As feature #3 X86_FEATURE_NONSTOP_TSC_S3 only exists on several generations
of Atom processorz, and is always coupled with X86_FEATURE_CONSTANT_TSC
and X86_FEATURE_NONSTOP_TSC, skip checking it, and also be more defensive
to use maximal 2 sockets.
The check is done inside tsc_init() before registering 'tsc-early' and
'tsc' clocksources, as there were cases that both of them had been
wrongly judged as unreliable.
For more background of tsc/watchdog, there is a good summary in [2]
[tglx} Update vs. jiffies:
On systems where the only remaining clocksource aside of TSC is jiffies
there is no way to make this work because that creates a circular
dependency. Jiffies accuracy depends on not missing a periodic timer
interrupt, which is not guaranteed. That could be detected by TSC, but as
TSC is not trusted this cannot be compensated. The consequence is a
circulus vitiosus which results in shutting down TSC and falling back to
the jiffies clocksource which is even more unreliable.
[1]. https://lore.kernel.org/lkml/87eekfk8bd.fsf@nanos.tec.linutronix.de/
[2]. https://lore.kernel.org/lkml/87a6pimt1f.ffs@nanos.tec.linutronix.de/
[ tglx: Refine comment and amend changelog ]
Fixes: 6e3cd95234 ("x86/hpet: Use another crystalball to evaluate HPET usability")
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "Paul E. McKenney" <paulmck@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211117023751.24190-2-feng.tang@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09f736aa95 upstream.
Turns out some xHC controllers require all 64 bits in the CRCR register
to be written to execute a command abort.
The lower 32 bits containing the command abort bit is written first.
In case the command ring stops before we write the upper 32 bits then
hardware may use these upper bits to set the commnd ring dequeue pointer.
Solve this by making sure the upper 32 bits contain a valid command
ring dequeue pointer.
The original patch that only wrote the first 32 to stop the ring went
to stable, so this fix should go there as well.
Fixes: ff0e50d356 ("xhci: Fix command ring pointer corruption while aborting a command")
Cc: stable@vger.kernel.org
Tested-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211126122340.1193239-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3dfac26e2e upstream.
Fix a division by zero in `vgacon_resize' with a backtrace like:
vgacon_resize
vc_do_resize
vgacon_init
do_bind_con_driver
do_unbind_con_driver
fbcon_fb_unbind
do_unregister_framebuffer
do_register_framebuffer
register_framebuffer
__drm_fb_helper_initial_config_and_unlock
drm_helper_hpd_irq_event
dw_hdmi_irq
irq_thread
kthread
caused by `c->vc_cell_height' not having been initialized. This has
only started to trigger with commit 860dafa902 ("vt: Fix character
height handling with VT_RESIZEX"), however the ultimate offender is
commit 50ec42edd9 ("[PATCH] Detaching fbcon: fix vgacon to allow
retaking of the console").
Said commit has added a call to `vc_resize' whenever `vgacon_init' is
called with the `init' argument set to 0, which did not happen before.
And the call is made before a key vgacon boot parameter retrieved in
`vgacon_startup' has been propagated in `vgacon_init' for `vc_resize' to
use to the console structure being worked on. Previously the parameter
was `c->vc_font.height' and now it is `c->vc_cell_height'.
In this particular scenario the registration of fbcon has failed and vt
resorts to vgacon. Now fbcon does have initialized `c->vc_font.height'
somehow, unlike `c->vc_cell_height', which is why this code did not
crash before, but either way the boot parameters should have been copied
to the console structure ahead of the call to `vc_resize' rather than
afterwards, so that first the call has a chance to use them and second
they do not change the console structure to something possibly different
from what was used by `vc_resize'.
Move the propagation of the vgacon boot parameters ahead of the call to
`vc_resize' then. Adjust the comment accordingly.
Fixes: 50ec42edd9 ("[PATCH] Detaching fbcon: fix vgacon to allow retaking of the console")
Cc: stable@vger.kernel.org # v2.6.18+
Reported-by: Wim Osterholt <wim@djo.tudelft.nl>
Reported-by: Pavel V. Panteleev <panteleev_p@mcst.ru>
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2110252317110.58149@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f9fee4cde upstream.
On newer debian releases the debian-provided "installkernel" script is
installed in /usr/sbin. Fix the kernel install.sh script to look for the
script in this directory as well.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org> # v3.13+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d7c29b777 upstream.
Default KBUILD_IMAGE to $(boot)/bzImage if a self-extracting
(CONFIG_PARISC_SELF_EXTRACT=y) kernel is to be built.
This fixes the bindeb-pkg make target.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c07e45553d ]
Commit
18ec54fdd6 ("x86/speculation: Prepare entry code for Spectre v1 swapgs mitigations")
added FENCE_SWAPGS_{KERNEL|USER}_ENTRY for conditional SWAPGS. In
paranoid_entry(), it uses only FENCE_SWAPGS_KERNEL_ENTRY for both
branches. This is because the fence is required for both cases since the
CR3 write is conditional even when PTI is enabled.
But
96b2371413 ("x86/entry/64: Switch CR3 before SWAPGS in paranoid entry")
changed the order of SWAPGS and the CR3 write. And it missed the needed
FENCE_SWAPGS_KERNEL_ENTRY for the user gsbase case.
Add it back by changing the branches so that FENCE_SWAPGS_KERNEL_ENTRY
can cover both branches.
[ bp: Massage, fix typos, remove obsolete comment while at it. ]
Fixes: 96b2371413 ("x86/entry/64: Switch CR3 before SWAPGS in paranoid entry")
Signed-off-by: Lai Jiangshan <laijs@linux.alibaba.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20211126101209.8613-2-jiangshanlai@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 53c9d92409 ]
SWAPGS is used only for interrupts coming from user mode or for
returning to user mode. So there is no reason to use the PARAVIRT
framework, as it can easily be replaced by an ALTERNATIVE depending
on X86_FEATURE_XENPV.
There are several instances using the PV-aware SWAPGS macro in paths
which are never executed in a Xen PV guest. Replace those with the
plain swapgs instruction. For SWAPGS_UNSAFE_STACK the same applies.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20210120135555.32594-5-jgross@suse.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 315c4f8848 ]
Commit d81ae8aac8 ("sched/uclamp: Fix initialization of struct
uclamp_rq") introduced a bug where uclamp_max of the rq is not reset to
match the woken up task's uclamp_max when the rq is idle.
The code was relying on rq->uclamp_max initialized to zero, so on first
enqueue
static inline void uclamp_rq_inc_id(struct rq *rq, struct task_struct *p,
enum uclamp_id clamp_id)
{
...
if (uc_se->value > READ_ONCE(uc_rq->value))
WRITE_ONCE(uc_rq->value, uc_se->value);
}
was actually resetting it. But since commit d81ae8aac8 changed the
default to 1024, this no longer works. And since rq->uclamp_flags is
also initialized to 0, neither above code path nor uclamp_idle_reset()
update the rq->uclamp_max on first wake up from idle.
This is only visible from first wake up(s) until the first dequeue to
idle after enabling the static key. And it only matters if the
uclamp_max of this task is < 1024 since only then its uclamp_max will be
effectively ignored.
Fix it by properly initializing rq->uclamp_flags = UCLAMP_FLAG_IDLE to
ensure uclamp_idle_reset() is called which then will update the rq
uclamp_max value as expected.
Fixes: d81ae8aac8 ("sched/uclamp: Fix initialization of struct uclamp_rq")
Signed-off-by: Qais Yousef <qais.yousef@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Valentin Schneider <Valentin.Schneider@arm.com>
Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Link: https://lkml.kernel.org/r/20211202112033.1705279-1-qais.yousef@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c8f6a2e31 ]
In the native case, PER_CPU_VAR(cpu_tss_rw + TSS_sp0) is the
trampoline stack. But XEN pv doesn't use trampoline stack, so
PER_CPU_VAR(cpu_tss_rw + TSS_sp0) is also the kernel stack.
In that case, source and destination stacks are identical, which means
that reusing swapgs_restore_regs_and_return_to_usermode() in XEN pv
would cause %rsp to move up to the top of the kernel stack and leave the
IRET frame below %rsp.
This is dangerous as it can be corrupted if #NMI / #MC hit as either of
these events occurring in the middle of the stack pushing would clobber
data on the (original) stack.
And, with XEN pv, swapgs_restore_regs_and_return_to_usermode() pushing
the IRET frame on to the original address is useless and error-prone
when there is any future attempt to modify the code.
[ bp: Massage commit message. ]
Fixes: 7f2590a110 ("x86/entry/64: Use a per-CPU trampoline stack for IDT entries")
Signed-off-by: Lai Jiangshan <laijs@linux.alibaba.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lkml.kernel.org/r/20211126101209.8613-4-jiangshanlai@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1367afaa2e ]
The commit
c758907004 ("x86/entry/64: Remove unneeded kernel CR3 switching")
removed a CR3 write in the faulting path of load_gs_index().
But the path's FENCE_SWAPGS_USER_ENTRY has no fence operation if PTI is
enabled, see spectre_v1_select_mitigation().
Rather, it depended on the serializing CR3 write of SWITCH_TO_KERNEL_CR3
and since it got removed, add a FENCE_SWAPGS_KERNEL_ENTRY call to make
sure speculation is blocked.
[ bp: Massage commit message and comment. ]
Fixes: c758907004 ("x86/entry/64: Remove unneeded kernel CR3 switching")
Signed-off-by: Lai Jiangshan <laijs@linux.alibaba.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20211126101209.8613-3-jiangshanlai@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d5379d047 ]
Properly type the operands being passed to __put_user()/__get_user().
Otherwise, these routines truncate data for dependent instructions
(e.g., INSW) and only read/write one byte.
This has been tested by sending a string with REP OUTSW to a port and
then reading it back in with REP INSW on the same port.
Previous behavior was to only send and receive the first char of the
size. For example, word operations for "abcd" would only read/write
"ac". With change, the full string is now written and read back.
Fixes: f980f9c31a (x86/sev-es: Compile early handler code into kernel image)
Signed-off-by: Michael Sterritt <sterritt@google.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Marc Orr <marcorr@google.com>
Reviewed-by: Peter Gonda <pgonda@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Link: https://lkml.kernel.org/r/20211119232757.176201-1-sterritt@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfbb307c62 ]
The error paths in the prepare_vmcs02() function are supposed to set
*entry_failure_code but this path does not. It leads to using an
uninitialized variable in the caller.
Fixes: 71f7347025 ("KVM: nVMX: Load GUEST_IA32_PERF_GLOBAL_CTRL MSR on VM-Entry")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Message-Id: <20211130125337.GB24578@kili>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb1d220da0 ]
If we run the following perf command in an AMD Milan guest:
perf stat \
-e cpu/event=0x1d0/ \
-e cpu/event=0x1c7/ \
-e cpu/umask=0x1f,event=0x18e/ \
-e cpu/umask=0x7,event=0x18e/ \
-e cpu/umask=0x18,event=0x18e/ \
./workload
dmesg will report a #GP warning from an unchecked MSR access
error on MSR_F15H_PERF_CTLx.
This is because according to APM (Revision: 4.03) Figure 13-7,
the bits [35:32] of AMD PerfEvtSeln register is a part of the
event select encoding, which extends the EVENT_SELECT field
from 8 bits to 12 bits.
Opportunistically update pmu->reserved_bits for reserved bit 19.
Reported-by: Jim Mattson <jmattson@google.com>
Fixes: ca724305a2 ("KVM: x86/vPMU: Implement AMD vPMU code for KVM")
Signed-off-by: Like Xu <likexu@tencent.com>
Message-Id: <20211118130320.95997-1-likexu@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 060a0fb721 upstream.
Remove the warn trace message - it's not a correct check here, because
the function can still be called on the device in DOWN state
Fixes: 508f2e3dce ("net: atlantic: split rx and tx per-queue stats")
Signed-off-by: Sameer Saurabh <ssaurabh@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2087ced0fc upstream.
B0 is the main and widespread device revision of atlantic2 HW. In the
current state, driver will incorrectly fetch the statistics for this
revision.
Fixes: 5cfd54d7dc ("net: atlantic: minimal A2 fw_ops")
Signed-off-by: Dmitry Bogdanov <dbezrukov@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 03fa512189 upstream.
Since Half Duplex mode has been deprecated by the firmware, driver should
not advertise Half Duplex speed in ethtool support link speed values.
Fixes: 071a02046c ("net: atlantic: A2: half duplex support")
Signed-off-by: Sameer Saurabh <ssaurabh@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 413d5e09ca upstream.
At the late production stages new dev ids were introduced. These are
now in production, so its important for the driver to recognize these.
And also fix the board caps for AQC115C adapter.
Fixes: b3f0c79cba ("net: atlantic: A2 hw_ops skeleton")
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2465c80223 upstream.
The correct way to reflect firmware version is to use bundle version.
Hence populating the same instead of MAC fw version.
Fixes: c1be0bf092 ("net: atlantic: common functions needed for basic A2 init/deinit hw_ops")
Signed-off-by: Sameer Saurabh <ssaurabh@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa685acd98 upstream.
When 2.5G is advertised, N-Base should be advertised against the T-base
caps. N5G is out of use in baseline code and driver should treat both 5G
and N5G (and also 2.5G and N2.5G) equally from user perspective.
Fixes: 5cfd54d7dc ("net: atlantic: minimal A2 fw_ops")
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa1dcb5646 upstream.
The max waiting period (of 1 ms) while reading the data from FW shared
buffer is too small for certain types of data (e.g., stats). There's a
chance that FW could be updating buffer at the same time and driver
would be unsuccessful in reading data. Firmware manual recommends to
have 1 sec timeout to fix this issue.
Fixes: 5cfd54d7dc ("net: atlantic: minimal A2 fw_ops")
Signed-off-by: Dmitry Bogdanov <dbezrukov@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4840d537c upstream.
In particular, we need to ensure all the necessary blocks are switched
to 64b mode (a5xx+) otherwise the high bits of the address of the BO to
snapshot state into will be ignored, resulting in:
*** gpu fault: ttbr0=0000000000000000 iova=0000000000012000 dir=READ type=TRANSLATION source=CP (0,0,0,0)
platform 506a000.gmu: [drm:a6xx_gmu_set_oob] *ERROR* Timeout waiting for GMU OOB set BOOT_SLUMBER: 0x0
Fixes: 4f776f4511 ("drm/msm/gpu: Convert the GPU show function to use the GPU state")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20211108180122.487859-1-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4d25abf97 upstream.
In commit 142639a52a ("drm/msm/a6xx: fix crashstate capture for
A650") we changed a6xx_get_gmu_registers() to read 3 sets of
registers. Unfortunately, we didn't change the memory allocation for
the array. That leads to a KASAN warning (this was on the chromeos-5.4
kernel, which has the problematic commit backported to it):
BUG: KASAN: slab-out-of-bounds in _a6xx_get_gmu_registers+0x144/0x430
Write of size 8 at addr ffffff80c89432b0 by task A618-worker/209
CPU: 5 PID: 209 Comm: A618-worker Tainted: G W 5.4.156-lockdep #22
Hardware name: Google Lazor Limozeen without Touchscreen (rev5 - rev8) (DT)
Call trace:
dump_backtrace+0x0/0x248
show_stack+0x20/0x2c
dump_stack+0x128/0x1ec
print_address_description+0x88/0x4a0
__kasan_report+0xfc/0x120
kasan_report+0x10/0x18
__asan_report_store8_noabort+0x1c/0x24
_a6xx_get_gmu_registers+0x144/0x430
a6xx_gpu_state_get+0x330/0x25d4
msm_gpu_crashstate_capture+0xa0/0x84c
recover_worker+0x328/0x838
kthread_worker_fn+0x32c/0x574
kthread+0x2dc/0x39c
ret_from_fork+0x10/0x18
Allocated by task 209:
__kasan_kmalloc+0xfc/0x1c4
kasan_kmalloc+0xc/0x14
kmem_cache_alloc_trace+0x1f0/0x2a0
a6xx_gpu_state_get+0x164/0x25d4
msm_gpu_crashstate_capture+0xa0/0x84c
recover_worker+0x328/0x838
kthread_worker_fn+0x32c/0x574
kthread+0x2dc/0x39c
ret_from_fork+0x10/0x18
Fixes: 142639a52a ("drm/msm/a6xx: fix crashstate capture for A650")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20211103153049.1.Idfa574ccb529d17b69db3a1852e49b580132035c@changeid
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 19f36edf14 upstream.
Correct an error where setting /proc/sys/net/rds/tcp/rds_tcp_rcvbuf would
instead modify the socket's sk_sndbuf and would leave sk_rcvbuf untouched.
Fixes: c6a58ffed5 ("RDS: TCP: Add sysctl tunables for sndbuf/rcvbuf on rds-tcp socket")
Signed-off-by: William Kucharski <william.kucharski@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 213f5f8f31 upstream.
Before commit faa041a40b ("ipv4: Create cleanup helper for fib_nh")
changes to net->ipv4.fib_num_tclassid_users were protected by RTNL.
After the change, this is no longer the case, as free_fib_info_rcu()
runs after rcu grace period, without rtnl being held.
Fixes: faa041a40b ("ipv4: Create cleanup helper for fib_nh")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Ahern <dsahern@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f4a8adbfe4 upstream.
The commit c55211892f ("dpaa2-eth: support PTP Sync packet one-step
timestamping") forgets to destroy workqueue at the end of remove
function.
Fix this by adding destroy_workqueue before fsl_mc_portal_free and
free_netdev.
Fixes: c55211892f ("dpaa2-eth: support PTP Sync packet one-step timestamping")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b83f5ac7d9 upstream.
'bitmap_fill()' fills a bitmap one 'long' at a time.
It is likely that an exact number of bits is expected.
Use 'bitmap_set()' instead in order not to set unexpected bits.
Fixes: e531f76757 ("net: mvpp2: handle cases where more CPUs are available than s/w threads")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 817b653160 upstream.
On most systems request for IRQ 0 will fail, phylib will print an error message
and fall back to polling. To fix this set the phydev->irq to PHY_POLL if no IRQ
is available.
Fixes: cc89c323a3 ("lan78xx: Use irq_domain for phy interrupt from USB Int. EP")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Sven Schuchmann <schuchmann@schleissheimer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a05431b22b upstream.
ipv6_addr_bind/ipv4_addr_bind are function names. Previously, bind test
would not be run by default due to the wrong case names
Fixes: 34d0302ab8 ("selftests: Add ipv6 address bind tests to fcnal-test")
Fixes: 75b2b2b3db ("selftests: Add ipv4 address bind tests to fcnal-test")
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit addad76431 upstream.
In mlx4_en_try_alloc_resources(), mlx4_en_copy_priv() is called and
tmp->tx_cq will be freed on the error path of mlx4_en_copy_priv().
After that mlx4_en_alloc_resources() is called and there is a dereference
of &tmp->tx_cq[t][i] in mlx4_en_alloc_resources(), which could lead to
a use after free problem on failure of mlx4_en_copy_priv().
Fix this bug by adding a check of mlx4_en_copy_priv()
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_MLX4_EN=m show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: ec25bc04ed ("net/mlx4_en: Add resilience in low memory systems")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20211130164438.190591-1-zhou1615@umn.edu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 35b6b28e69 upstream.
When branch target identifiers are in use, code reachable via an
indirect branch requires a BTI landing pad at the branch target site.
When building FTRACE_WITH_REGS atop patchable-function-entry, we miss
BTIs at the start start of the `ftrace_caller` and `ftrace_regs_caller`
trampolines, and when these are called from a module via a PLT (which
will use a `BR X16`), we will encounter a BTI failure, e.g.
| # insmod lkdtm.ko
| lkdtm: No crash points registered, enable through debugfs
| # echo function_graph > /sys/kernel/debug/tracing/current_tracer
| # cat /sys/kernel/debug/provoke-crash/DIRECT
| Unhandled 64-bit el1h sync exception on CPU0, ESR 0x34000001 -- BTI
| CPU: 0 PID: 174 Comm: cat Not tainted 5.16.0-rc2-dirty #3
| Hardware name: linux,dummy-virt (DT)
| pstate: 60400405 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=jc)
| pc : ftrace_caller+0x0/0x3c
| lr : lkdtm_debugfs_open+0xc/0x20 [lkdtm]
| sp : ffff800012e43b00
| x29: ffff800012e43b00 x28: 0000000000000000 x27: ffff800012e43c88
| x26: 0000000000000000 x25: 0000000000000000 x24: ffff0000c171f200
| x23: ffff0000c27b1e00 x22: ffff0000c2265240 x21: ffff0000c23c8c30
| x20: ffff8000090ba380 x19: 0000000000000000 x18: 0000000000000000
| x17: 0000000000000000 x16: ffff80001002bb4c x15: 0000000000000000
| x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000900ff0
| x11: ffff0000c4166310 x10: ffff800012e43b00 x9 : ffff8000104f2384
| x8 : 0000000000000001 x7 : 0000000000000000 x6 : 000000000000003f
| x5 : 0000000000000040 x4 : ffff800012e43af0 x3 : 0000000000000001
| x2 : ffff8000090b0000 x1 : ffff0000c171f200 x0 : ffff0000c23c8c30
| Kernel panic - not syncing: Unhandled exception
| CPU: 0 PID: 174 Comm: cat Not tainted 5.16.0-rc2-dirty #3
| Hardware name: linux,dummy-virt (DT)
| Call trace:
| dump_backtrace+0x0/0x1a4
| show_stack+0x24/0x30
| dump_stack_lvl+0x68/0x84
| dump_stack+0x1c/0x38
| panic+0x168/0x360
| arm64_exit_nmi.isra.0+0x0/0x80
| el1h_64_sync_handler+0x68/0xd4
| el1h_64_sync+0x78/0x7c
| ftrace_caller+0x0/0x3c
| do_dentry_open+0x134/0x3b0
| vfs_open+0x38/0x44
| path_openat+0x89c/0xe40
| do_filp_open+0x8c/0x13c
| do_sys_openat2+0xbc/0x174
| __arm64_sys_openat+0x6c/0xbc
| invoke_syscall+0x50/0x120
| el0_svc_common.constprop.0+0xdc/0x100
| do_el0_svc+0x84/0xa0
| el0_svc+0x28/0x80
| el0t_64_sync_handler+0xa8/0x130
| el0t_64_sync+0x1a0/0x1a4
| SMP: stopping secondary CPUs
| Kernel Offset: disabled
| CPU features: 0x0,00000f42,da660c5f
| Memory Limit: none
| ---[ end Kernel panic - not syncing: Unhandled exception ]---
Fix this by adding the required `BTI C`, as we only require these to be
reachable via BL for direct calls or BR X16/X17 for PLTs. For now, these
are open-coded in the function prologue, matching the style of the
`__hwasan_tag_mismatch` trampoline.
In future we may wish to consider adding a new SYM_CODE_START_*()
variant which has an implicit BTI.
When ftrace is built atop mcount, the trampolines are marked with
SYM_FUNC_START(), and so get an implicit BTI. We may need to change
these over to SYM_CODE_START() in future for RELIABLE_STACKTRACE, in
case we need to apply special care aroud the return address being
rewritten.
Fixes: 97fed779f2 ("arm64: bti: Provide Kconfig for kernel mode BTI")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20211129135709.2274019-1-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7e5b9bfa6 upstream.
On ARM v6 and later, we define CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
because the ordinary load/store instructions (ldr, ldrh, ldrb) can
tolerate any misalignment of the memory address. However, load/store
double and load/store multiple instructions (ldrd, ldm) may still only
be used on memory addresses that are 32-bit aligned, and so we have to
use the CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS macro with care, or we
may end up with a severe performance hit due to alignment traps that
require fixups by the kernel. Testing shows that this currently happens
with clang-13 but not gcc-11. In theory, any compiler version can
produce this bug or other problems, as we are dealing with undefined
behavior in C99 even on architectures that support this in hardware,
see also https://gcc.gnu.org/bugzilla/show_bug.cgi?id=100363.
Fortunately, the get_unaligned() accessors do the right thing: when
building for ARMv6 or later, the compiler will emit unaligned accesses
using the ordinary load/store instructions (but avoid the ones that
require 32-bit alignment). When building for older ARM, those accessors
will emit the appropriate sequence of ldrb/mov/orr instructions. And on
architectures that can truly tolerate any kind of misalignment, the
get_unaligned() accessors resolve to the leXX_to_cpup accessors that
operate on aligned addresses.
Since the compiler will in fact emit ldrd or ldm instructions when
building this code for ARM v6 or later, the solution is to use the
unaligned accessors unconditionally on architectures where this is
known to be fast. The _aligned version of the hash function is
however still needed to get the best performance on architectures
that cannot do any unaligned access in hardware.
This new version avoids the undefined behavior and should produce
the fastest hash on all architectures we support.
Link: https://lore.kernel.org/linux-arm-kernel/20181008211554.5355-4-ard.biesheuvel@linaro.org/
Link: https://lore.kernel.org/linux-crypto/CAK8P3a2KfmmGDbVHULWevB0hv71P2oi2ZCHEAqT=8dQfa0=cqQ@mail.gmail.com/
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Fixes: 2c956a6077 ("siphash: add cryptographically secure PRF")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d4741eacd upstream.
There are various problems related to netlink notifications for mpls route
changes in response to interfaces being deleted:
* delete interface of only nexthop
DELROUTE notification is missing RTA_OIF attribute
* delete interface of non-last nexthop
NEWROUTE notification is missing entirely
* delete interface of last nexthop
DELROUTE notification is missing nexthop
All of these problems stem from the fact that existing routes are modified
in-place before sending a notification. Restructure mpls_ifdown() to avoid
changing the route in the DELROUTE cases and to create a copy in the
NEWROUTE case.
Fixes: f8efb73c97 ("mpls: multipath route support")
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e2dabc4f7e upstream.
In qlcnic_83xx_add_rings(), the indirect function of
ahw->hw_ops->alloc_mbx_args will be called to allocate memory for
cmd.req.arg, and there is a dereference of it in qlcnic_83xx_add_rings(),
which could lead to a NULL pointer dereference on failure of the
indirect function like qlcnic_83xx_alloc_mbx_args().
Fix this bug by adding a check of alloc_mbx_args(), this patch
imitates the logic of mbx_cmd()'s failure handling.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_QLCNIC=m show no new warnings, and our
static analyzer no longer warns about this code.
Fixes: 7f9664525f ("qlcnic: 83xx memory map and HW access routine")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Link: https://lore.kernel.org/r/20211130110848.109026-1-zhou1615@umn.edu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dacb5d8875 upstream.
Steffen reported a TCP stream corruption for HTTP requests
served by the apache web-server using a cifs mount-point
and memory mapping the relevant file.
The root cause is quite similar to the one addressed by
commit 20eb4f29b6 ("net: fix sk_page_frag() recursion from
memory reclaim"). Here the nested access to the task page frag
is caused by a page fault on the (mmapped) user-space memory
buffer coming from the cifs file.
The page fault handler performs an smb transaction on a different
socket, inside the same process context. Since sk->sk_allaction
for such socket does not prevent the usage for the task_frag,
the nested allocation modify "under the hood" the page frag
in use by the outer sendmsg call, corrupting the stream.
The overall relevant stack trace looks like the following:
httpd 78268 [001] 3461630.850950: probe:tcp_sendmsg_locked:
ffffffff91461d91 tcp_sendmsg_locked+0x1
ffffffff91462b57 tcp_sendmsg+0x27
ffffffff9139814e sock_sendmsg+0x3e
ffffffffc06dfe1d smb_send_kvec+0x28
[...]
ffffffffc06cfaf8 cifs_readpages+0x213
ffffffff90e83c4b read_pages+0x6b
ffffffff90e83f31 __do_page_cache_readahead+0x1c1
ffffffff90e79e98 filemap_fault+0x788
ffffffff90eb0458 __do_fault+0x38
ffffffff90eb5280 do_fault+0x1a0
ffffffff90eb7c84 __handle_mm_fault+0x4d4
ffffffff90eb8093 handle_mm_fault+0xc3
ffffffff90c74f6d __do_page_fault+0x1ed
ffffffff90c75277 do_page_fault+0x37
ffffffff9160111e page_fault+0x1e
ffffffff9109e7b5 copyin+0x25
ffffffff9109eb40 _copy_from_iter_full+0xe0
ffffffff91462370 tcp_sendmsg_locked+0x5e0
ffffffff91462370 tcp_sendmsg_locked+0x5e0
ffffffff91462b57 tcp_sendmsg+0x27
ffffffff9139815c sock_sendmsg+0x4c
ffffffff913981f7 sock_write_iter+0x97
ffffffff90f2cc56 do_iter_readv_writev+0x156
ffffffff90f2dff0 do_iter_write+0x80
ffffffff90f2e1c3 vfs_writev+0xa3
ffffffff90f2e27c do_writev+0x5c
ffffffff90c042bb do_syscall_64+0x5b
ffffffff916000ad entry_SYSCALL_64_after_hwframe+0x65
The cifs filesystem rightfully sets sk_allocations to GFP_NOFS,
we can avoid the nesting using the sk page frag for allocation
lacking the __GFP_FS flag. Do not define an additional mm-helper
for that, as this is strictly tied to the sk page frag usage.
v1 -> v2:
- use a stricted sk_page_frag() check instead of reordering the
code (Eric)
Reported-by: Steffen Froemer <sfroemer@redhat.com>
Fixes: 5640f76858 ("net: use a per task frag allocator")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b0f38e1597 upstream.
Fix section mismatch warnings in xtsonic. The first one appears to be
bogus and after fixing the second one, the first one is gone.
WARNING: modpost: vmlinux.o(.text+0x529adc): Section mismatch in reference from the function sonic_get_stats() to the function .init.text:set_reset_devices()
The function sonic_get_stats() references
the function __init set_reset_devices().
This is often because sonic_get_stats lacks a __init
annotation or the annotation of set_reset_devices is wrong.
WARNING: modpost: vmlinux.o(.text+0x529b3b): Section mismatch in reference from the function xtsonic_probe() to the function .init.text:sonic_probe1()
The function xtsonic_probe() references
the function __init sonic_probe1().
This is often because xtsonic_probe lacks a __init
annotation or the annotation of sonic_probe1 is wrong.
Fixes: 74f2a5f0ef ("xtensa: Add support for the Sonic Ethernet device for the XT2000 board.")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Chris Zankel <chris@zankel.net>
Cc: linux-xtensa@linux-xtensa.org
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Link: https://lore.kernel.org/r/20211130063947.7529-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b12764695c upstream.
CBUS transfers have always been atomic, but after commit 63b96983a5
("i2c: core: introduce callbacks for atomic transfers") we started to see
warnings during e.g. poweroff as the atomic callback is not explicitly set.
Fix that.
Fixes the following WARNING seen during Nokia N810 power down:
[ 786.570617] reboot: Power down
[ 786.573913] ------------[ cut here ]------------
[ 786.578826] WARNING: CPU: 0 PID: 672 at drivers/i2c/i2c-core.h:40 i2c_smbus_xfer+0x100/0x110
[ 786.587799] No atomic I2C transfer handler for 'i2c-2'
Fixes: 63b96983a5 ("i2c: core: introduce callbacks for atomic transfers")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31b90a95cc upstream.
In case of receiving a NACK, the dma transfer should be stopped
to avoid feeding data into the FIFO.
Also ensure to properly return the proper error code and avoid
waiting for the end of the dma completion in case of
error happening during the transmission.
Fixes: 7ecc8cfde5 ("i2c: i2c-stm32f7: Add DMA support")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c21d02ca4 upstream.
While handling an error during transfer (ex: NACK), it could
happen that the driver has already written data into TXDR
before the transfer get stopped.
This commit add TXDR Flush after end of transfer in case of error to
avoid sending a wrong data on any other slave upon next transfer.
Fixes: aeb068c572 ("i2c: i2c-stm32f7: add driver")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e3fd72171 upstream.
Use 2-factor argument form kvcalloc() instead of kvzalloc().
Link: https://github.com/KSPP/linux/issues/162
Fixes: e7096c131e ("net: WireGuard secure network tunnel")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
[Jason: Gustavo's link above is for KSPP, but this isn't actually a
security fix, as table_size is bounded to 8192 anyway, and gcc realizes
this, so the codegen comes out to be about the same.]
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb32f4f606 upstream.
If we're being delivered packets from multiple CPUs so quickly that the
ring lock is contended for CPU tries, then it's safe to assume that the
queue is near capacity anyway, so just drop the packet rather than
spinning. This helps deal with multicore DoS that can interfere with
data path performance. It _still_ does not completely fix the issue, but
it again chips away at it.
Reported-by: Streun Fabio <fstreun@student.ethz.ch>
Fixes: e7096c131e ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 886fcee939 upstream.
Apparently the spinlock on incoming_handshake's skb_queue is highly
contended, and a torrent of handshake or cookie packets can bring the
data plane to its knees, simply by virtue of enqueueing the handshake
packets to be processed asynchronously. So, we try switching this to a
ring buffer to hopefully have less lock contention. This alleviates the
problem somewhat, though it still isn't perfect, so future patches will
have to improve this further. However, it at least doesn't completely
diminish the data plane.
Reported-by: Streun Fabio <fstreun@student.ethz.ch>
Reported-by: Joel Wanner <joel.wanner@inf.ethz.ch>
Fixes: e7096c131e ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 20ae1d6aa1 upstream.
Each peer's endpoint contains a dst_cache entry that takes a reference
to another netdev. When the containing namespace exits, we take down the
socket and prevent future sockets from being created (by setting
creating_net to NULL), which removes that potential reference on the
netns. However, it doesn't release references to the netns that a netdev
cached in dst_cache might be taking, so the netns still might fail to
exit. Since the socket is gimped anyway, we can simply clear all the
dst_caches (by way of clearing the endpoint src), which will release all
references.
However, the current dst_cache_reset function only releases those
references lazily. But it turns out that all of our usages of
wg_socket_clear_peer_endpoint_src are called from contexts that are not
exactly high-speed or bottle-necked. For example, when there's
connection difficulty, or when userspace is reconfiguring the interface.
And in particular for this patch, when the netns is exiting. So for
those cases, it makes more sense to call dst_release immediately. For
that, we add a small helper function to dst_cache.
This patch also adds a test to netns.sh from Hangbin Liu to ensure this
doesn't regress.
Tested-by: Hangbin Liu <liuhangbin@gmail.com>
Reported-by: Xiumei Mu <xmu@redhat.com>
Cc: Toke Høiland-Jørgensen <toke@redhat.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Fixes: 900575aa33 ("wireguard: device: avoid circular netns references")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 782c72af56 upstream.
We previously removed the restriction on looping to self, and then added
a test to make sure the kernel didn't blow up during a routing loop. The
kernel didn't blow up, thankfully, but on certain architectures where
skb fragmentation is easier, such as ppc64, the skbs weren't actually
being discarded after a few rounds through. But the test wasn't catching
this. So actually test explicitly for massive increases in tx to see if
we have a routing loop. Note that the actual loop problem will need to
be addressed in a different commit.
Fixes: b673e24aad ("wireguard: socket: remove errant restriction on looping to self")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae9287811b upstream.
A __rcu annotation got lost during refactoring, which caused sparse to
become enraged.
Fixes: bf7b042dc6 ("wireguard: allowedips: free empty intermediate nodes when removing single node")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 03ff1b1def upstream.
The selftests currently parse the kernel log at the end to track
potential memory leaks. With these tests now reading off the end of the
buffer, due to recent optimizations, some creation messages were lost,
making the tests think that there was a free without an alloc. Fix this
by increasing the kernel log size.
Fixes: 24b70eeeb4 ("wireguard: use synchronize_net rather than synchronize_rcu")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05b29633c7 upstream.
INVLPG operates on guest virtual address, which are represented by
vcpu->arch.walk_mmu. In nested virtualization scenarios,
kvm_mmu_invlpg() was using the wrong MMU structure; if L2's invlpg were
emulated by L0 (in practice, it hardly happen) when nested two-dimensional
paging is enabled, the call to ->tlb_flush_gva() would be skipped and
the hardware TLB entry would not be invalidated.
Signed-off-by: Lai Jiangshan <laijs@linux.alibaba.com>
Message-Id: <20211124122055.64424-5-jiangshanlai@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f80d15020 upstream.
Having a signed (1 << 31) constant for TCR_EL2_RES1 and CPTR_EL2_TCPAC
causes the upper 32-bit to be set to 1 when assigning them to a 64-bit
variable. Bit 32 in TCR_EL2 is no longer RES0 in ARMv8.7: with FEAT_LPA2
it changes the meaning of bits 49:48 and 9:8 in the stage 1 EL2 page
table entries. As a result of the sign-extension, a non-VHE kernel can
no longer boot on a model with ARMv8.7 enabled.
CPTR_EL2 still has the top 32 bits RES0 but we should preempt any future
problems
Make these top bit constants unsigned as per commit df655b75c4
("arm64: KVM: Avoid setting the upper 32 bits of VTCR_EL2 to 1").
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Chris January <Chris.January@arm.com>
Cc: <stable@vger.kernel.org>
Cc: Will Deacon <will@kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211125152014.2806582-1-catalin.marinas@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 53b7ca1a35 upstream.
Currently, checks for whether VT-d PI can be used refer to the current
status of the feature in the current vCPU; or they more or less pick
vCPU 0 in case a specific vCPU is not available.
However, these checks do not attempt to synchronize with changes to
the IRTE. In particular, there is no path that updates the IRTE when
APICv is re-activated on vCPU 0; and there is no path to wakeup a CPU
that has APICv disabled, if the wakeup occurs because of an IRTE
that points to a posted interrupt.
To fix this, always go through the VT-d PI path as long as there are
assigned devices and APICv is available on both the host and the VM side.
Since the relevant condition was copied over three times, take the hint
and factor it into a separate function.
Suggested-by: Sean Christopherson <seanjc@google.com>
Cc: stable@vger.kernel.org
Reviewed-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: David Matlack <dmatlack@google.com>
Message-Id: <20211123004311.2954158-5-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b4a5a5d56 upstream.
Flush the current VPID when handling KVM_REQ_TLB_FLUSH_GUEST instead of
always flushing vpid01. Any TLB flush that is triggered when L2 is
active is scoped to L2's VPID (if it has one), e.g. if L2 toggles CR4.PGE
and L1 doesn't intercept PGE writes, then KVM's emulation of the TLB
flush needs to be applied to L2's VPID.
Reported-by: Lai Jiangshan <jiangshanlai+lkml@gmail.com>
Fixes: 07ffaf343e ("KVM: nVMX: Sync all PGDs on nested transition with shadow paging")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211125014944.536398-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b285a5587 upstream.
Reject userspace memslots whose size exceeds the storage capacity of an
"unsigned long". KVM's uAPI takes the size as u64 to support large slots
on 64-bit hosts, but does not account for the size being truncated on
32-bit hosts in various flows. The access_ok() check on the userspace
virtual address in particular casts the size to "unsigned long" and will
check the wrong number of bytes.
KVM doesn't actually support slots whose size doesn't fit in an "unsigned
long", e.g. KVM's internal kvm_memory_slot.npages is an "unsigned long",
not a "u64", and misc arch specific code follows that behavior.
Fixes: fa3d315a4c ("KVM: Validate userspace_addr of memslot when registered")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Message-Id: <20211104002531.1176691-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 94ebc03545 upstream.
[Why]
When trying to lightup two 4k60 non-DSC displays behind a branch device
that supports DSC we can't lightup both at once due to bandwidth
limitations - each requires 48 VCPI slots but we only have 63.
[How]
The workaround already exists in the code but is guarded by a CONFIG
that cannot be set by the user and shouldn't need to be.
Check for specific branch device IDs to device whether to enable
the workaround for multiple display scenarios.
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cdef485217 upstream.
The kernel leaks memory when a `fib` rule is present in IPv6 nftables
firewall rules and a suppress_prefix rule is present in the IPv6 routing
rules (used by certain tools such as wg-quick). In such scenarios, every
incoming packet will leak an allocation in `ip6_dst_cache` slab cache.
After some hours of `bpftrace`-ing and source code reading, I tracked
down the issue to ca7a03c417 ("ipv6: do not free rt if
FIB_LOOKUP_NOREF is set on suppress rule").
The problem with that change is that the generic `args->flags` always have
`FIB_LOOKUP_NOREF` set[1][2] but the IPv6-specific flag
`RT6_LOOKUP_F_DST_NOREF` might not be, leading to `fib6_rule_suppress` not
decreasing the refcount when needed.
How to reproduce:
- Add the following nftables rule to a prerouting chain:
meta nfproto ipv6 fib saddr . mark . iif oif missing drop
This can be done with:
sudo nft create table inet test
sudo nft create chain inet test test_chain '{ type filter hook prerouting priority filter + 10; policy accept; }'
sudo nft add rule inet test test_chain meta nfproto ipv6 fib saddr . mark . iif oif missing drop
- Run:
sudo ip -6 rule add table main suppress_prefixlength 0
- Watch `sudo slabtop -o | grep ip6_dst_cache` to see memory usage increase
with every incoming ipv6 packet.
This patch exposes the protocol-specific flags to the protocol
specific `suppress` function, and check the protocol-specific `flags`
argument for RT6_LOOKUP_F_DST_NOREF instead of the generic
FIB_LOOKUP_NOREF when decreasing the refcount, like this.
[1]: ca7a03c417/net/ipv6/fib6_rules.c (L71)
[2]: ca7a03c417/net/ipv6/fib6_rules.c (L99)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215105
Fixes: ca7a03c417 ("ipv6: do not free rt if FIB_LOOKUP_NOREF is set on suppress rule")
Cc: stable@vger.kernel.org
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f48394cf1 upstream.
Trying to remove the fsl-sata module in the PPC64 GNU/Linux
leads to the following warning:
------------[ cut here ]------------
remove_proc_entry: removing non-empty directory 'irq/69',
leaking at least 'fsl-sata[ff0221000.sata]'
WARNING: CPU: 3 PID: 1048 at fs/proc/generic.c:722
.remove_proc_entry+0x20c/0x220
IRQMASK: 0
NIP [c00000000033826c] .remove_proc_entry+0x20c/0x220
LR [c000000000338268] .remove_proc_entry+0x208/0x220
Call Trace:
.remove_proc_entry+0x208/0x220 (unreliable)
.unregister_irq_proc+0x104/0x140
.free_desc+0x44/0xb0
.irq_free_descs+0x9c/0xf0
.irq_dispose_mapping+0x64/0xa0
.sata_fsl_remove+0x58/0xa0 [sata_fsl]
.platform_drv_remove+0x40/0x90
.device_release_driver_internal+0x160/0x2c0
.driver_detach+0x64/0xd0
.bus_remove_driver+0x70/0xf0
.driver_unregister+0x38/0x80
.platform_driver_unregister+0x14/0x30
.fsl_sata_driver_exit+0x18/0xa20 [sata_fsl]
---[ end trace 0ea876d4076908f5 ]---
The driver creates the mapping by calling irq_of_parse_and_map(),
so it also has to dispose the mapping. But the easy way out is to
simply use platform_get_irq() instead of irq_of_parse_map(). Also
we should adapt return value checking and propagate error values.
In this case the mapping is not managed by the device but by
the of core, so the device has not to dispose the mapping.
Fixes: faf0b2e5af ("drivers/ata: add support to Freescale 3.0Gbps SATA Controller")
Cc: stable@vger.kernel.org
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c8ad7e8cf upstream.
When the `rmmod sata_fsl.ko` command is executed in the PPC64 GNU/Linux,
a bug is reported:
==================================================================
BUG: Unable to handle kernel data access on read at 0x80000800805b502c
Oops: Kernel access of bad area, sig: 11 [#1]
NIP [c0000000000388a4] .ioread32+0x4/0x20
LR [80000000000c6034] .sata_fsl_port_stop+0x44/0xe0 [sata_fsl]
Call Trace:
.free_irq+0x1c/0x4e0 (unreliable)
.ata_host_stop+0x74/0xd0 [libata]
.release_nodes+0x330/0x3f0
.device_release_driver_internal+0x178/0x2c0
.driver_detach+0x64/0xd0
.bus_remove_driver+0x70/0xf0
.driver_unregister+0x38/0x80
.platform_driver_unregister+0x14/0x30
.fsl_sata_driver_exit+0x18/0xa20 [sata_fsl]
.__se_sys_delete_module+0x1ec/0x2d0
.system_call_exception+0xfc/0x1f0
system_call_common+0xf8/0x200
==================================================================
The triggering of the BUG is shown in the following stack:
driver_detach
device_release_driver_internal
__device_release_driver
drv->remove(dev) --> platform_drv_remove/platform_remove
drv->remove(dev) --> sata_fsl_remove
iounmap(host_priv->hcr_base); <---- unmap
kfree(host_priv); <---- free
devres_release_all
release_nodes
dr->node.release(dev, dr->data) --> ata_host_stop
ap->ops->port_stop(ap) --> sata_fsl_port_stop
ioread32(hcr_base + HCONTROL) <---- UAF
host->ops->host_stop(host)
The iounmap(host_priv->hcr_base) and kfree(host_priv) functions should
not be executed in drv->remove. These functions should be executed in
host_stop after port_stop. Therefore, we move these functions to the
new function sata_fsl_host_stop and bind the new function to host_stop.
Fixes: faf0b2e5af ("drivers/ata: add support to Freescale 3.0Gbps SATA Controller")
Cc: stable@vger.kernel.org
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 054aa8d439 upstream.
Jann Horn points out that there is another possible race wrt Unix domain
socket garbage collection, somewhat reminiscent of the one fixed in
commit cbcf01128d ("af_unix: fix garbage collect vs MSG_PEEK").
See the extended comment about the garbage collection requirements added
to unix_peek_fds() by that commit for details.
The race comes from how we can locklessly look up a file descriptor just
as it is in the process of being closed, and with the right artificial
timing (Jann added a few strategic 'mdelay(500)' calls to do that), the
Unix domain socket garbage collector could see the reference count
decrement of the close() happen before fget() took its reference to the
file and the file was attached onto a new file descriptor.
This is all (intentionally) correct on the 'struct file *' side, with
RCU lookups and lockless reference counting very much part of the
design. Getting that reference count out of order isn't a problem per
se.
But the garbage collector can get confused by seeing this situation of
having seen a file not having any remaining external references and then
seeing it being attached to an fd.
In commit cbcf01128d ("af_unix: fix garbage collect vs MSG_PEEK") the
fix was to serialize the file descriptor install with the garbage
collector by taking and releasing the unix_gc_lock.
That's not really an option here, but since this all happens when we are
in the process of looking up a file descriptor, we can instead simply
just re-check that the file hasn't been closed in the meantime, and just
re-do the lookup if we raced with a concurrent close() of the same file
descriptor.
Reported-and-tested-by: Jann Horn <jannh@google.com>
Acked-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52d04d4081 upstream.
When running without MIO support, with pci=nomio or for devices which
are not MIO-capable the zPCI subsystem generates pseudo-MMIO addresses
to allow access to PCI BARs via MMIO based Linux APIs even though the
platform uses function handles and BAR numbers.
This is done by stashing an index into our global IOMAP array which
contains the function handle in the 16 most significant bits of the
addresses returned by ioremap() always setting the most significant bit.
On the other hand the MIO addresses assigned by the platform for use,
while requiring special instructions, allow PCI access with virtually
mapped physical addresses. Now the problem is that these MIO addresses
and our own pseudo-MMIO addresses may overlap, while functionally this
would not be a problem by itself this overlap is detected by common code
as both address types are added as resources in the iomem_resource tree.
This leads to the overlapping resource claim of either the MIO capable
or non-MIO capable devices with being rejected.
Since PCI is tightly coupled to the use of the iomem_resource tree, see
for example the code for request_mem_region(), we can't reasonably get
rid of the overlap being detected by keeping our pseudo-MMIO addresses
out of the iomem_resource tree.
Instead let's move the range used by our own pseudo-MMIO addresses by
starting at (1UL << 62) and only using addresses below (1UL << 63) thus
avoiding the range currently used for MIO addresses.
Fixes: c7ff0e918a ("s390/pci: deal with devices that have no support for MIO instructions")
Cc: stable@vger.kernel.org # 5.3+
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c1b5a8466 upstream.
When I hot added a CPU, I found 'cpufreq' directory was not created
below /sys/devices/system/cpu/cpuX/.
It is because get_cpu_device() failed in add_cpu_dev_symlink().
cpufreq_add_dev() is the .add_dev callback of a CPU subsys interface.
It will be called when the CPU device registered into the system.
The call chain is as follows:
register_cpu()
->device_register()
->device_add()
->bus_probe_device()
->cpufreq_add_dev()
But only after the CPU device has been registered, we can get the
CPU device by get_cpu_device(), otherwise it will return NULL.
Since we already have the CPU device in cpufreq_add_dev(), pass
it to add_cpu_dev_symlink().
I noticed that the 'kobj' of the CPU device has been added into
the system before cpufreq_add_dev().
Fixes: 2f0ba790df ("cpufreq: Fix creation of symbolic links to policy directories")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d49eb91e8 upstream.
Currently when removing an ipmi_user the removal is deferred as a work on
the system's workqueue. Although this guarantees the free operation will
occur in non atomic context, it can race with the ipmi_msghandler module
removal (see [1]) . In case a remove_user work is scheduled for removal
and shortly after ipmi_msghandler module is removed we can end up in a
situation where the module is removed fist and when the work is executed
the system crashes with :
BUG: unable to handle page fault for address: ffffffffc05c3450
PF: supervisor instruction fetch in kernel mode
PF: error_code(0x0010) - not-present page
because the pages of the module are gone. In cleanup_ipmi() there is no
easy way to detect if there are any pending works to flush them before
removing the module. This patch creates a separate workqueue and schedules
the remove_work works on it. When removing the module the workqueue is
drained when destroyed to avoid the race.
[1] https://bugs.launchpad.net/bugs/1950666
Cc: stable@vger.kernel.org # 5.1
Fixes: 3b9a907223 (ipmi: fix sleep-in-atomic in free_user at cleanup SRCU user->release_barrier)
Signed-off-by: Ioanna Alifieraki <ioanna-maria.alifieraki@canonical.com>
Message-Id: <20211115131645.25116-1-ioanna-maria.alifieraki@canonical.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6bbfa44116 upstream.
The 'kprobe::data_size' is unsigned, thus it can not be negative. But if
user sets it enough big number (e.g. (size_t)-8), the result of 'data_size
+ sizeof(struct kretprobe_instance)' becomes smaller than sizeof(struct
kretprobe_instance) or zero. In result, the kretprobe_instance are
allocated without enough memory, and kretprobe accesses outside of
allocated memory.
To avoid this issue, introduce a max limitation of the
kretprobe::data_size. 4KB per instance should be OK.
Link: https://lkml.kernel.org/r/163836995040.432120.10322772773821182925.stgit@devnote2
Cc: stable@vger.kernel.org
Fixes: f47cd9b553 ("kprobes: kretprobe user entry-handler")
Reported-by: zhangyue <zhangyue1@kylinos.cn>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee201011c1 upstream.
IPCB/IP6CB need to be initialized when processing outbound v4 or v6 pkts
in the codepath of vrf device xmit function so that leftover garbage
doesn't cause futher code that uses the CB to incorrectly process the
pkt.
One occasion of the issue might occur when MPLS route uses the vrf
device as the outgoing device such as when the route is added using "ip
-f mpls route add <label> dev <vrf>" command.
The problems seems to exist since day one. Hence I put the day one
commits on the Fixes tags.
Fixes: 193125dbd8 ("net: Introduce VRF device driver")
Fixes: 35402e3136 ("net: Add IPv6 support to VRF device")
Cc: stable@vger.kernel.org
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20211130162637.3249-1-ssuryaextr@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7a61432dc8 ]
Possible recursive locking is detected by lockdep when SMC
falls back to TCP. The corresponding warnings are as follows:
============================================
WARNING: possible recursive locking detected
5.16.0-rc1+ #18 Tainted: G E
--------------------------------------------
wrk/1391 is trying to acquire lock:
ffff975246c8e7d8 (&ei->socket.wq.wait){..-.}-{3:3}, at: smc_switch_to_fallback+0x109/0x250 [smc]
but task is already holding lock:
ffff975246c8f918 (&ei->socket.wq.wait){..-.}-{3:3}, at: smc_switch_to_fallback+0xfe/0x250 [smc]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&ei->socket.wq.wait);
lock(&ei->socket.wq.wait);
*** DEADLOCK ***
May be due to missing lock nesting notation
2 locks held by wrk/1391:
#0: ffff975246040130 (sk_lock-AF_SMC){+.+.}-{0:0}, at: smc_connect+0x43/0x150 [smc]
#1: ffff975246c8f918 (&ei->socket.wq.wait){..-.}-{3:3}, at: smc_switch_to_fallback+0xfe/0x250 [smc]
stack backtrace:
Call Trace:
<TASK>
dump_stack_lvl+0x56/0x7b
__lock_acquire+0x951/0x11f0
lock_acquire+0x27a/0x320
? smc_switch_to_fallback+0x109/0x250 [smc]
? smc_switch_to_fallback+0xfe/0x250 [smc]
_raw_spin_lock_irq+0x3b/0x80
? smc_switch_to_fallback+0x109/0x250 [smc]
smc_switch_to_fallback+0x109/0x250 [smc]
smc_connect_fallback+0xe/0x30 [smc]
__smc_connect+0xcf/0x1090 [smc]
? mark_held_locks+0x61/0x80
? __local_bh_enable_ip+0x77/0xe0
? lockdep_hardirqs_on+0xbf/0x130
? smc_connect+0x12a/0x150 [smc]
smc_connect+0x12a/0x150 [smc]
__sys_connect+0x8a/0xc0
? syscall_enter_from_user_mode+0x20/0x70
__x64_sys_connect+0x16/0x20
do_syscall_64+0x34/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
The nested locking in smc_switch_to_fallback() is considered to
possibly cause a deadlock because smc_wait->lock and clc_wait->lock
are the same type of lock. But actually it is safe so far since
there is no other place trying to obtain smc_wait->lock when
clc_wait->lock is held. So the patch replaces spin_lock() with
spin_lock_nested() to avoid false report by lockdep.
Link: https://lkml.org/lkml/2021/11/19/962
Fixes: 2153bd1e3d ("Transfer remaining wait queue entries during fallback")
Reported-by: syzbot+e979d3597f48262cb4ee@syzkaller.appspotmail.com
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Acked-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0fa68da72c ]
The definition of macro MOTO_SROM_BUG is:
#define MOTO_SROM_BUG (lp->active == 8 && (get_unaligned_le32(
dev->dev_addr) & 0x00ffffff) == 0x3e0008)
and the if statement
if (MOTO_SROM_BUG) lp->active = 0;
using this macro indicates lp->active could be 8. If lp->active is 8 and
the second comparison of this macro is false. lp->active will remain 8 in:
lp->phy[lp->active].gep = (*p ? p : NULL); p += (2 * (*p) + 1);
lp->phy[lp->active].rst = (*p ? p : NULL); p += (2 * (*p) + 1);
lp->phy[lp->active].mc = get_unaligned_le16(p); p += 2;
lp->phy[lp->active].ana = get_unaligned_le16(p); p += 2;
lp->phy[lp->active].fdx = get_unaligned_le16(p); p += 2;
lp->phy[lp->active].ttm = get_unaligned_le16(p); p += 2;
lp->phy[lp->active].mci = *p;
However, the length of array lp->phy is 8, so array overflows can occur.
To fix these possible array overflows, we first check lp->active and then
return -EINVAL if it is greater or equal to ARRAY_SIZE(lp->phy) (i.e. 8).
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Teng Qi <starmiku1207184332@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61217be886 ]
In line 5001, if all id in the array 'lp->phy[8]' is not 0, when the
'for' end, the 'k' is 8.
At this time, the array 'lp->phy[8]' may be out of bound.
Signed-off-by: zhangyue <zhangyue1@kylinos.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f9c55c806 ]
The offset value is used in pointer math on skb->data.
Since ipv6_skip_exthdr may return -1 the pointer to uh and th
may not point to the actual udp and tcp headers and potentially
overwrite other stuff. This is why I think this should be checked.
EDIT: added {}'s, thanks Kees
Signed-off-by: Jordy Zomer <jordy@pwning.systems>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a66998e0fb ]
The if statement:
if (port >= DSAF_GE_NUM)
return;
limits the value of port less than DSAF_GE_NUM (i.e., 8).
However, if the value of port is 6 or 7, an array overflow could occur:
port_rst_off = dsaf_dev->mac_cb[port]->port_rst_off;
because the length of dsaf_dev->mac_cb is DSAF_MAX_PORT_NUM (i.e., 6).
To fix this possible array overflow, we first check port and if it is
greater than or equal to DSAF_MAX_PORT_NUM, the function returns.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Teng Qi <starmiku1207184332@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1527f69204 ]
AMD requires that the SATA controller be configured for devsleep in order
for S0i3 entry to work properly.
commit b1a9585cc3 ("ata: ahci: Enable DEVSLP by default on x86 with
SLP_S0") sets up a kernel policy to enable devsleep on Intel mobile
platforms that are using s0ix. Add the PCI ID for the SATA controller in
Green Sardine platforms to extend this policy by default for AMD based
systems using s0i3 as well.
Cc: Nehal-bakulchandra Shah <Nehal-bakulchandra.Shah@amd.com>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214091
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2cf49e00d4 ]
In SRIOV configuration, the reset may failed to bring asic back to normal but stop cpsch
already been called, the start_cpsch will not be called since there is no resume in this
case. When reset been triggered again, driver should avoid to do uninitialization again.
Signed-off-by: shaoyunl <shaoyun.liu@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0c2f8b670 ]
We can race where iscsi_session_recovery_timedout() has woken up the error
handler thread and it's now setting the devices to offline, and
session_recovery_timedout()'s call to scsi_target_unblock() is also trying
to set the device's state to transport-offline. We can then get a mix of
states.
For the case where we can't relogin we want the devices to be in
transport-offline so when we have repaired the connection
__iscsi_unblock_session() can set the state back to running.
Set the device state then call into libiscsi to wake up the error handler.
Link: https://lore.kernel.org/r/20211105221048.6541-2-michael.christie@oracle.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99b63316c3 ]
During the suspend is in process, thermal_zone_device_update bails out
thermal zone re-evaluation for any sensor trip violation without
setting next valid trip to that sensor. It assumes during resume
it will re-evaluate same thermal zone and update trip. But when it is
in suspend temperature goes down and on resume path while updating
thermal zone if temperature is less than previously violated trip,
thermal zone set trip function evaluates the same previous high and
previous low trip as new high and low trip. Since there is no change
in high/low trip, it bails out from thermal zone set trip API without
setting any trip. It leads to a case where sensor high trip or low
trip is disabled forever even though thermal zone has a valid high
or low trip.
During thermal zone device init, reset thermal zone previous high
and low trip. It resolves above mentioned scenario.
Signed-off-by: Manaf Meethalavalappu Pallikunhi <manafm@codeaurora.org>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a91cf0ffbc ]
When a disk has write caching disabled, we skip submission of a bio with
flush and sync requests before writing the superblock, since it's not
needed. However when the integrity checker is enabled, this results in
reports that there are metadata blocks referred by a superblock that
were not properly flushed. So don't skip the bio submission only when
the integrity checker is enabled for the sake of simplicity, since this
is a debug tool and not meant for use in non-debug builds.
fstests/btrfs/220 trigger a check-integrity warning like the following
when CONFIG_BTRFS_FS_CHECK_INTEGRITY=y and the disk with WCE=0.
btrfs: attempt to write superblock which references block M @5242880 (sdb2/5242880/0) which is not flushed out of disk's write cache (block flush_gen=1, dev->flush_gen=0)!
------------[ cut here ]------------
WARNING: CPU: 28 PID: 843680 at fs/btrfs/check-integrity.c:2196 btrfsic_process_written_superblock+0x22a/0x2a0 [btrfs]
CPU: 28 PID: 843680 Comm: umount Not tainted 5.15.0-0.rc5.39.el8.x86_64 #1
Hardware name: Dell Inc. Precision T7610/0NK70N, BIOS A18 09/11/2019
RIP: 0010:btrfsic_process_written_superblock+0x22a/0x2a0 [btrfs]
RSP: 0018:ffffb642afb47940 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000000000002 RCX: 0000000000000000
RDX: 00000000ffffffff RSI: ffff8b722fc97d00 RDI: ffff8b722fc97d00
RBP: ffff8b5601c00000 R08: 0000000000000000 R09: c0000000ffff7fff
R10: 0000000000000001 R11: ffffb642afb476f8 R12: ffffffffffffffff
R13: ffffb642afb47974 R14: ffff8b5499254c00 R15: 0000000000000003
FS: 00007f00a06d4080(0000) GS:ffff8b722fc80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fff5cff5ff0 CR3: 00000001c0c2a006 CR4: 00000000001706e0
Call Trace:
btrfsic_process_written_block+0x2f7/0x850 [btrfs]
__btrfsic_submit_bio.part.19+0x310/0x330 [btrfs]
? bio_associate_blkg_from_css+0xa4/0x2c0
btrfsic_submit_bio+0x18/0x30 [btrfs]
write_dev_supers+0x81/0x2a0 [btrfs]
? find_get_pages_range_tag+0x219/0x280
? pagevec_lookup_range_tag+0x24/0x30
? __filemap_fdatawait_range+0x6d/0xf0
? __raw_callee_save___native_queued_spin_unlock+0x11/0x1e
? find_first_extent_bit+0x9b/0x160 [btrfs]
? __raw_callee_save___native_queued_spin_unlock+0x11/0x1e
write_all_supers+0x1b3/0xa70 [btrfs]
? __raw_callee_save___native_queued_spin_unlock+0x11/0x1e
btrfs_commit_transaction+0x59d/0xac0 [btrfs]
close_ctree+0x11d/0x339 [btrfs]
generic_shutdown_super+0x71/0x110
kill_anon_super+0x14/0x30
btrfs_kill_super+0x12/0x20 [btrfs]
deactivate_locked_super+0x31/0x70
cleanup_mnt+0xb8/0x140
task_work_run+0x6d/0xb0
exit_to_user_mode_prepare+0x1f0/0x200
syscall_exit_to_user_mode+0x12/0x30
do_syscall_64+0x46/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f009f711dfb
RSP: 002b:00007fff5cff7928 EFLAGS: 00000246 ORIG_RAX: 00000000000000a6
RAX: 0000000000000000 RBX: 000055b68c6c9970 RCX: 00007f009f711dfb
RDX: 0000000000000001 RSI: 0000000000000000 RDI: 000055b68c6c9b50
RBP: 0000000000000000 R08: 000055b68c6ca900 R09: 00007f009f795580
R10: 0000000000000000 R11: 0000000000000246 R12: 000055b68c6c9b50
R13: 00007f00a04bf184 R14: 0000000000000000 R15: 00000000ffffffff
---[ end trace 2c4b82abcef9eec4 ]---
S-65536(sdb2/65536/1)
-->
M-1064960(sdb2/1064960/1)
Reviewed-by: Filipe Manana <fdmanana@gmail.com>
Signed-off-by: Wang Yugui <wangyugui@e16-tech.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5dbc4cb466 ]
There is a difference in how architectures treat "mem=" option. For some
that is an amount of online memory, for s390 and x86 this is the limiting
max address. Some memblock api like memblock_enforce_memory_limit()
take limit argument and explicitly treat it as the size of online memory,
and use __find_max_addr to convert it to an actual max address. Current
s390 usage:
memblock_enforce_memory_limit(memblock_end_of_DRAM());
yields different results depending on presence of memory holes (offline
memory blocks in between online memory). If there are no memory holes
limit == max_addr in memblock_enforce_memory_limit() and it does trim
online memory and reserved memory regions. With memory holes present it
actually does nothing.
Since we already use memblock_remove() explicitly to trim online memory
regions to potential limit (think mem=, kdump, addressing limits, etc.)
drop the usage of memblock_enforce_memory_limit() altogether. Trimming
reserved regions should not be required, since we now use
memblock_set_current_limit() to limit allocations and any explicit memory
reservations above the limit is an actual problem we should not hide.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39f5329218 ]
When WWAN device wake from S3 deep, under thinkpad platform,
WWAN would be disabled. This disable status could be checked
by command 'nmcli r wwan' or 'rfkill list'.
Issue analysis as below:
When host resume from S3 deep, thinkpad_acpi driver would
call hotkey_resume() function. Finnaly, it will use
wan_get_status to check the current status of WWAN device.
During this resume progress, wan_get_status would always
return off even WWAN boot up completely.
In patch V2, Hans said 'sw_state should be unchanged
after a suspend/resume. It's better to drop the
tpacpi_rfk_update_swstate call all together from the
resume path'.
And it's confimed by Lenovo that GWAN is no longer
available from WHL generation because the design does not
match with current pin control.
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Link: https://lore.kernel.org/r/20211108060648.8212-1-slark_xiao@163.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6def480181 ]
When kmemdup called failed and register_net_sysctl return NULL, should
return ENOMEM instead of ENOBUFS
Signed-off-by: liuguoqiang <liuguoqiang@uniontech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b922f62259 ]
This bug report shows up when running our research tools. The
reports is SOOB read, but it seems SOOB write is also possible
a few lines below.
In details, fw.len and sw.len are inputs coming from io. A len
over the size of self->rpc triggers SOOB. The patch fixes the
bugs by adding sanity checks.
The bugs are triggerable with compromised/malfunctioning devices.
They are potentially exploitable given they first leak up to
0xffff bytes and able to overwrite the region later.
The patch is tested with QEMU emulater.
This is NOT tested with a real device.
Attached is the log we found by fuzzing.
BUG: KASAN: slab-out-of-bounds in
hw_atl_utils_fw_upload_dwords+0x393/0x3c0 [atlantic]
Read of size 4 at addr ffff888016260b08 by task modprobe/213
CPU: 0 PID: 213 Comm: modprobe Not tainted 5.6.0 #1
Call Trace:
dump_stack+0x76/0xa0
print_address_description.constprop.0+0x16/0x200
? hw_atl_utils_fw_upload_dwords+0x393/0x3c0 [atlantic]
? hw_atl_utils_fw_upload_dwords+0x393/0x3c0 [atlantic]
__kasan_report.cold+0x37/0x7c
? aq_hw_read_reg_bit+0x60/0x70 [atlantic]
? hw_atl_utils_fw_upload_dwords+0x393/0x3c0 [atlantic]
kasan_report+0xe/0x20
hw_atl_utils_fw_upload_dwords+0x393/0x3c0 [atlantic]
hw_atl_utils_fw_rpc_call+0x95/0x130 [atlantic]
hw_atl_utils_fw_rpc_wait+0x176/0x210 [atlantic]
hw_atl_utils_mpi_create+0x229/0x2e0 [atlantic]
? hw_atl_utils_fw_rpc_wait+0x210/0x210 [atlantic]
? hw_atl_utils_initfw+0x9f/0x1c8 [atlantic]
hw_atl_utils_initfw+0x12a/0x1c8 [atlantic]
aq_nic_ndev_register+0x88/0x650 [atlantic]
? aq_nic_ndev_init+0x235/0x3c0 [atlantic]
aq_pci_probe+0x731/0x9b0 [atlantic]
? aq_pci_func_init+0xc0/0xc0 [atlantic]
local_pci_probe+0xd3/0x160
pci_device_probe+0x23f/0x3e0
Reported-by: Brendan Dolan-Gavitt <brendandg@nyu.edu>
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2153bd1e3d ]
The SMC fallback is incomplete currently. There may be some
wait queue entries remaining in smc socket->wq, which should
be removed to clcsocket->wq during the fallback.
For example, in nginx/wrk benchmark, this issue causes an
all-zeros test result:
server: nginx -g 'daemon off;'
client: smc_run wrk -c 1 -t 1 -d 5 http://11.200.15.93/index.html
Running 5s test @ http://11.200.15.93/index.html
1 threads and 1 connections
Thread Stats Avg Stdev Max ± Stdev
Latency 0.00us 0.00us 0.00us -nan%
Req/Sec 0.00 0.00 0.00 -nan%
0 requests in 5.00s, 0.00B read
Requests/sec: 0.00
Transfer/sec: 0.00B
The reason for this all-zeros result is that when wrk used SMC
to replace TCP, it added an eppoll_entry into smc socket->wq
and expected to be notified if epoll events like EPOLL_IN/
EPOLL_OUT occurred on the smc socket.
However, once a fallback occurred, wrk switches to use clcsocket.
Now it is clcsocket->wq instead of smc socket->wq which will
be woken up. The eppoll_entry remaining in smc socket->wq does
not work anymore and wrk stops the test.
This patch fixes this issue by removing remaining wait queue
entries from smc socket->wq to clcsocket->wq during the fallback.
Link: https://www.spinics.net/lists/netdev/msg779769.html
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb162bb2b4 ]
When PHY_SUN6I_MIPI_DPHY is selected, and RESET_CONTROLLER
is not selected, Kbuild gives the following warning:
WARNING: unmet direct dependencies detected for PHY_SUN6I_MIPI_DPHY
Depends on [n]: (ARCH_SUNXI [=n] || COMPILE_TEST [=y]) && HAS_IOMEM [=y] && COMMON_CLK [=y] && RESET_CONTROLLER [=n]
Selected by [y]:
- DRM_SUN6I_DSI [=y] && HAS_IOMEM [=y] && DRM_SUN4I [=y]
This is because DRM_SUN6I_DSI selects PHY_SUN6I_MIPI_DPHY
without selecting or depending on RESET_CONTROLLER, despite
PHY_SUN6I_MIPI_DPHY depending on RESET_CONTROLLER.
These unmet dependency bugs were detected by Kismet,
a static analysis tool for Kconfig. Please advise if this
is not the appropriate solution.
v2:
Fixed indentation to match the rest of the file.
Signed-off-by: Julian Braha <julianbraha@gmail.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20211109032351.43322-1-julianbraha@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3506eee81 ]
Fix the length of holes reported at the end of a file: the length is
relative to the beginning of the extent, not the seek position which is
rounded down to the filesystem block size.
This bug went unnoticed for some time, but is now caught by the
following assertion in iomap_iter_done():
WARN_ON_ONCE(iter->iomap.offset + iter->iomap.length <= iter->pos)
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49462e2be1 ]
Before this patch, evict would clear the iopen glock's gl_object after
releasing the inode glock. In the meantime, another process could reuse
the same block and thus glocks for a new inode. It would lock the inode
glock (exclusively), and then the iopen glock (shared). The shared
locking mode doesn't provide any ordering against the evict, so by the
time the iopen glock is reused, evict may not have gotten to setting
gl_object to NULL.
Fix that by releasing the iopen glock before the inode glock in
gfs2_evict_inode.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>gl_object
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9b91b6b019 upstream.
There's possibility of an ABBA deadlock in case of a splice write to an
overlayfs file and a concurrent splice write to a corresponding real file.
The call chain for splice to an overlay file:
-> do_splice [takes sb_writers on overlay file]
-> do_splice_from
-> iter_file_splice_write [takes pipe->mutex]
-> vfs_iter_write
...
-> ovl_write_iter [takes sb_writers on real file]
And the call chain for splice to a real file:
-> do_splice [takes sb_writers on real file]
-> do_splice_from
-> iter_file_splice_write [takes pipe->mutex]
Syzbot successfully bisected this to commit 82a763e61e ("ovl: simplify
file splice").
Fix by reverting the write part of the above commit and by adding missing
bits from ovl_write_iter() into ovl_splice_write().
Fixes: 82a763e61e ("ovl: simplify file splice")
Reported-and-tested-by: syzbot+579885d1a9a833336209@syzkaller.appspotmail.com
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Cc: Stan Hu <stanhu@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 82a763e61e upstream.
generic_file_splice_read() and iter_file_splice_write() will call back into
f_op->iter_read() and f_op->iter_write() respectively. These already do
the real file lookup and cred override. So the code in ovl_splice_read()
and ovl_splice_write() is redundant.
In addition the ovl_file_accessed() call in ovl_splice_write() is
incorrect, though probably harmless.
Fix by calling generic_file_splice_read() and iter_file_splice_write()
directly.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Cc: Stan Hu <stanhu@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f015d89a4 upstream.
The mechanism in use to allow the client to see the results of COPY/CLONE
is to drop those pages from the pagecache. This forces the client to read
those pages once more from the server. However, truncate_pagecache_range()
zeros out partial pages instead of dropping them. Let us instead use
invalidate_inode_pages2_range() with full-page offsets to ensure the client
properly sees the results of COPY/CLONE operations.
Cc: <stable@vger.kernel.org> # v4.7+
Fixes: 2e72448b07 ("NFS: Add COPY nfs operation")
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-12-08 09:03:17 +01:00
2442 changed files with 29293 additions and 13209 deletions
This repository contains the Linux kernel used on the Raspberry Pi. If you believe that the issue you are seeing is kernel-related, this is the right place. If not, we have other repositories for the GPU firmware at [github.com/raspberrypi/firmware](https://github.com/raspberrypi/firmware) and Raspberry Pi userland applications at [github.com/raspberrypi/userland](https://github.com/raspberrypi/userland). If you have problems with the Raspbian distribution packages, report them in the [github.com/RPi-Distro/repo](https://github.com/RPi-Distro/repo). If you simply have a question, then [the Raspberry Pi forums](https://www.raspberrypi.org/forums) are the best place to ask it.
**Describe the bug**
Add a clear and concise description of what you think the bug is.
**To reproduce**
List the steps required to reproduce the issue.
**Expected behaviour**
Add a clear and concise description of what you expected to happen.
**Actual behaviour**
Add a clear and concise description of what actually happened.
**System**
Copy and paste the results of the raspinfo command in to this section. Alternatively, copy and paste a pastebin link, or add answers to the following questions:
* Which model of Raspberry Pi? e.g. Pi3B+, PiZeroW
* Which OS and version (`cat /etc/rpi-issue`)?
* Which firmware version (`vcgencmd version`)?
* Which kernel version (`uname -a`)?
**Logs**
If applicable, add the relevant output from `dmesg` or similar.
description:Create a report to help us fix your issue
body:
- type:markdown
attributes:
value:|
**Is this the right place for my bug report?**
This repository contains the Linux kernel used on the Raspberry Pi.
If you believe that the issue you are seeing is kernel-related, this is the right place.
If not, we have other repositories for the GPU firmware at [github.com/raspberrypi/firmware](https://github.com/raspberrypi/firmware) and Raspberry Pi userland applications at [github.com/raspberrypi/userland](https://github.com/raspberrypi/userland).
If you have problems with the Raspbian distribution packages, report them in the [github.com/RPi-Distro/repo](https://github.com/RPi-Distro/repo).
If you simply have a question, then [the Raspberry Pi forums](https://www.raspberrypi.org/forums) are the best place to ask it.
- type:textarea
id:description
attributes:
label:Describe the bug
description:|
Add a clear and concise description of what you think the bug is.
validations:
required:true
- type:textarea
id:reproduce
attributes:
label:Steps to reproduce the behaviour
description:|
List the steps required to reproduce the issue.
validations:
required:true
- type:dropdown
id:model
attributes:
label:Device (s)
description:Onwhich device you are facing the bug?
multiple:true
options:
- Raspberry Pi Zero
- Raspberry Pi Zero W/WH
- Raspberry Pi Zero 2 W
- Raspberry Pi 1 Mod. A
- Raspberry Pi 1 Mod. A+
- Raspberry Pi 1 Mod. B
- Raspberry Pi 1 Mod. B+
- Raspberry Pi 2 Mod. B
- Raspberry Pi 2 Mod. B v1.2
- Raspberry Pi 3 Mod. A+
- Raspberry Pi 3 Mod. B
- Raspberry Pi 3 Mod. B+
- Raspberry Pi 4 Mod. B
- Raspberry Pi 400
- Raspberry Pi CM1
- Raspberry Pi CM3
- Raspberry Pi CM3 Lite
- Raspberry Pi CM3+
- Raspberry Pi CM3+ Lite
- Raspberry Pi CM4
- Raspberry Pi CM4 Lite
- Other
validations:
required:true
- type:textarea
id:system
attributes:
label:System
description:|
Copy and paste the results of the raspinfo command in to this section.
Alternatively, copy and paste a pastebin link, or add answers to the following questions:
* Which OS and version (`cat /etc/rpi-issue`)?
* Which firmware version (`vcgencmd version`)?
* Which kernel version (`uname -a`)?
validations:
required:true
- type:textarea
id:logs
attributes:
label:Logs
description:|
If applicable, add the relevant output from `dmesg` or similar.
about:"Please do not use GitHub for asking questions. If you simply have a question, then the Raspberry Pi forums are the best place to ask it. Thanks in advance for helping us keep the issue tracker clean!"
- name:"⛔ Problems with the Raspbian distribution packages"
url:https://github.com/RPi-Distro/repo
about:"If you have problems with the Raspbian distribution packages, please report them in the github.com/RPi-Distro/repo."
- Firmware status: Show if Indirect Branch Restricted Speculation (IBRS) is
used to protect against Spectre variant 2 attacks when calling firmware (x86 only).
@@ -468,7 +483,7 @@ Spectre variant 2
before invoking any firmware code to prevent Spectre variant 2 exploits
using the firmware.
Using kernel address space randomization (CONFIG_RANDOMIZE_SLAB=y
Using kernel address space randomization (CONFIG_RANDOMIZE_BASE=y
and CONFIG_SLAB_FREELIST_RANDOM=y in the kernel configuration) makes
attacks on the kernel generally more difficult.
@@ -584,12 +599,13 @@ kernel command line.
Specific mitigations can also be selected manually:
retpoline
replace indirect branches
retpoline,generic
google's original retpoline
retpoline,amd
AMD-specific minimal thunk
retpoline auto pick between generic,lfence
retpoline,generic Retpolines
retpoline,lfence LFENCE; indirect branch
retpoline,amd alias for retpoline,lfence
eibrs enhanced IBRS
eibrs,retpoline enhanced IBRS + Retpolines
eibrs,lfence enhanced IBRS + LFENCE
Not specifying this option is equivalent to
spectre_v2=auto.
@@ -730,7 +746,7 @@ AMD white papers:
.._spec_ref6:
[6] `Software techniques for managing speculation on AMD processors <https://developer.amd.com/wp-content/resources/90343-B_SoftwareTechniquesforManagingSpeculation_WP_7-18Update_FNL.pdf>`_.
[6] `Software techniques for managing speculation on AMD processors <https://developer.amd.com/wp-content/resources/Managing-Speculation-on-AMD-Processors.pdf>`_.
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
